The Design, Prototyping, and Formative Evaluation of an Assistive Robotic Table (ART) for Stroke Patients.

PubMed

Threatt, Anthony L; Merino, Jessica; Brooks, Johnell O; Healy, Stan; Truesdail, Constance; Manganelli, Joseph; Walker, Ian; Green, Keith Evan

2017-04-01

This article presents the results of an exploratory study in which 14 healthcare subject matter experts (H-SMEs) in addition to four research and design subject matter experts (RD-SMEs) at a regional rehabilitation hospital engaged in a series of complementary, participatory activities in order to design an assistive robotic table (ART). As designers, human factor experts, and healthcare professionals continue to work to integrate assistive human-robot technologies in healthcare, it is imperative to understand how the technology affects patient care from clinicians' perspectives. Fourteen clinical H-SMEs rated a subset of conceptual ART design ideas; participated in the iterative design process of ART; and evaluated a final cardboard prototype, the rehabilitation hospital's current over-the-bed table (OBT), an ART built with true materials, and two therapy surface prototypes. Four RD-SMEs conducted a heuristic evaluation on the ART built with true materials. Data were analyzed by frequency and content analysis. The results include a design and prototype for the next generation ART and a pneumatically controlled therapy surface, a broadened list of specifications for the future design and implementation of assistive robotic furniture, and final observations. When compared to the rehabilitation hospital's current OBT, the developed ART in this study was successful. Designing novel features is dependent upon ensuring patient safety. The inclusion of clinicians in the participatory iterative design and evaluation process and the use of personas provided a broadened list of specifications for the successful implementation of assistive robotic furniture.

Special ISO Class 6 Cleanroom for the Lunar Reconnaissance Orbiter (LRO) Project

NASA Technical Reports Server (NTRS)

Matthews, Richard A.; Matthews, Scott A.

2008-01-01

The parameters and restrictions for a horizontal flow ISO Class 6 Clean room to support the assembly of the new LRO (Lunar Reconnaissance Orbiter) were unusual. The project time line was critical. A novel Clean room design was developed and built within the time restraints. This paper describes the design criteria, timing, successful performance, and future benefits of this unique Clean room project.

Enterprise Architecture Planning in developing A planning Information System: a Case Study of Semarang State University

NASA Astrophysics Data System (ADS)

Budiman, Kholiq; Prahasto, Toni; Kusumawardhani, Amie

2018-02-01

This research has applied an integrated design and development of planning information system, which is been designed using Enterprise Architecture Planning. Frequent discrepancy between planning and realization of the budget that has been made, resulted in ineffective planning, is one of the reason for doing this research. The design using EAP aims to keep development aligned and in line with the strategic direction of the organization. In the practice, EAP is carried out in several stages of the planning initiation, identification and definition of business functions, proceeded with architectural design and EA implementation plan that has been built. In addition to the design of the Enterprise Architecture, this research carried out the implementation, and was tested by several methods of black box and white box. Black box testing method is used to test the fundamental aspects of the software, tested by two kinds of testing, first is using User Acceptance Testing and the second is using software functionality testing. White box testing method is used to test the effectiveness of the code in the software, tested using unit testing. Tests conducted using white box and black box on the integrated planning information system, is declared successful. Success in the software testing can not be ascertained if the software built has not shown any distinction from prior circumstance to the development of this integrated planning information system. For ensuring the success of this system implementation, the authors test consistency between the planning of data and the realization of prior-use of the information system, until after-use information system. This consistency test is done by reducing the time data of the planning and realization time. From the tabulated data, the planning information system that has been built reduces the difference between the planning time and the realization time, in which indicates that the planning information system can motivate the planner unit in realizing the budget that has been designed. It also proves that the value chain of the information planning system has brought implications for budget realization.

Teachers' Learning in an Innovative School

ERIC Educational Resources Information Center

Bissaker, Kerry; Heath, Jayne

2005-01-01

The successful establishment of a purpose-built innovative school designed to support new ways of teaching and learning in the senior secondary years, particularly in the area of science and mathematics, required a comprehensive and research-based professional development policy and program. Planning professional learning opportunities for the…

SCARLET I: Mechanization solutions for deployable concentrator optics integrated with rigid array technology

NASA Technical Reports Server (NTRS)

Wachholz, James J.; Murphy, David M.

1996-01-01

The SCARLET I (Solar Concentrator Army with Refractive Linear Element Technology) solar array wing was designed and built to demonstrate, in flight, the feasibility of integrating deployable concentrator optics within the design envelope of typical rigid array technology. Innovative mechanism designs were used throughout the array, and a full series of qualification tests were successfully performed in anticipation of a flight on the Multiple Experiment Transporter to Earth Orbit and Return (METEOR) spacecraft. Even though the Conestoga launch vehicle was unable to place the spacecraft in orbit, the program effort was successful in achieving the milestones of analytical and design development functional validation, and flight qualification, thus leading to a future flight evaluation for the SCARLET technology.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. UAH students designed and built the rocket and AM students designed the payload. In this picture, AM students prepare their payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity, prior to launch.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. UAH students designed and built the rocket and AM students designed the payload. In this picture, AM students prepare their payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity, prior to launch.

Reusable launch vehicle development research

NASA Technical Reports Server (NTRS)

1995-01-01

NASA has generated a program approach for a SSTO reusable launch vehicle technology (RLV) development which includes a follow-on to the Ballistic Missile Defense Organization's (BMDO) successful DC-X program, the DC-XA (Advanced). Also, a separate sub-scale flight demonstrator, designated the X-33, will be built and flight tested along with numerous ground based technologies programs. For this to be a successful effort, a balance between technical, schedule, and budgetary risks must be attained. The adoption of BMDO's 'fast track' management practices will be a key element in the eventual success of NASA's effort.

High-Frequency Learning.

ERIC Educational Resources Information Center

Hollenbeck, Michelle D.

1997-01-01

For the past five years, Andover, Kansas middle-schoolers in an amateur radio club and class have sent and received Morse code messages, assembled and soldered circuit boards, designed and built antenna systems, and used computer programs to analyze radio communications problems. A successful bond issue financed a ham shack enabling students to…

Field/Work, Site, and Other Matters: Exploring Design Practice across Disciplines

ERIC Educational Resources Information Center

Pirrie, Anne; Brown, James Benedict

2011-01-01

This article explores educational research and theory in the area of the built environment by reflecting on the challenges of interdisciplinary enquiry and the prerequisites for successful interdisciplinary practice. The genesis of a particular example of interdisciplinary collaboration is explored, and the authors come to the deceptively simple…

FEASIBILITY STUDY TO DEMONSTRATE APPLICABILITY OF TUNABLE INFRARED LASER EMISSION SPECTROSCOPY TECHNOLOGY TO MEASURE AIR POLLUTION

EPA Science Inventory

This project involves the real-time measurement of air quality using open-path IR spectroscopy. A prototype open-path tunable laser absorption spectroscopy instrument was designed, built, and successfully operated for several hundred hours between October and December 2000. The...

Microgravity

NASA Image and Video Library

2003-01-22

The Jet Propulsion Laboratory has designed and built an electronic nose system -- ENose -- to take on the duty of staying alert for smells that could indicate hazardous conditions in a closed spacecraft environment. Its sensors are tailored so they conduct electricity differently when an air stream carries a particular chemical across them. JPL has designed and built a 3-pound flight version (shown with palm-size control and data computer). The active parts are 32 sensors, each with a different mix of polymers saturated with carbon. When certain chemicals latch onto a sensor, they change how the sensor conducts electricity. This signal tells how much of a compound is in the air. The electronic nose flown aboard STS-95 in 1998 was capable of successfully detecting 10 toxic compounds.

Learning through Plastic Filament Extrusion

ERIC Educational Resources Information Center

Orr, Taylor; Flowers, Jim

2015-01-01

3D printing is becoming ever more popular in both the manufacturing world as well as in technology and engineering education classrooms all over the United States. 3D printing is an additive manufacturing process in which successive layers of material are built up to produce three-dimensional objects from computer-aided design (CAD) files, making…

Washington: Symbol and City. An Educator's Guide to the Exhibit.

ERIC Educational Resources Information Center

Toby Levine Communications, Inc., Bethesda, MD.

Designed to make a visit to Washington, D.C. a successful learning experience for students by helping them understand the evolution of the city into what it is today, this teacher's guide presents themes and activities to accommodate many teaching and learning styles. Three sections of activities explore how the built environment symbolizes…

On the Measurement and Visualization of Analysis Activity: A Study of Successful Strategies for Web-Based Information Analysis

ERIC Educational Resources Information Center

Zelik, Daniel J.

2012-01-01

Cognitive Systems Engineering (CSE) has a history built, in part, on leveraging representational design to improve system performance. Traditionally, however, CSE has focused on visual representation of "monitored" processes--active, ongoing, and interconnected activities occurring in a system of interest and monitored by human…

SCARLET I: Mechanization solutions for deployable concentrator optics integrated with rigid array technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wachholz, J.J.; Murphy, D.M.

1996-05-01

The SCARLET I (Solar Concentrator Army with Refractive Linear Element Technology) solar array wing was designed and built to demonstrate, in flight, the feasibility of integrating deployable concentrator optics within the design envelope of typical rigid array technology. Innovative mechanism designs were used throughout the array, and a full series of qualification tests were successfully performed in anticipation of a flight on the Multiple Experiment Transporter to Earth Orbit and Return (METEOR) spacecraft. Even though the Conestoga launch vehicle was unable to place the spacecraft in orbit, the program effort was successful in achieving the milestones of analytical and designmore » development functional validation, and flight qualification, thus leading to a future flight evaluation for the SCARLET technology.« less

Development of High-Power Hall Thruster Power Processing Units at NASA GRC

NASA Technical Reports Server (NTRS)

Pinero, Luis R.; Bozak, Karin E.; Santiago, Walter; Scheidegger, Robert J.; Birchenough, Arthur G.

2015-01-01

NASA GRC successfully designed, built and tested four different power processor concepts for high power Hall thrusters. Each design satisfies unique goals including the evaluation of a novel silicon carbide semiconductor technology, validation of innovative circuits to overcome the problems with high input voltage converter design, development of a direct-drive unit to demonstrate potential benefits, or simply identification of lessonslearned from the development of a PPU using a conventional design approach. Any of these designs could be developed further to satisfy NASA's needs for high power electric propulsion in the near future.

Light-weight extension tubes for compressed-air garden sprayers

Treesearch

Thomas W. McConkey; Charles E. Swett

1967-01-01

To hand-spray taller trees safely and efficiently, 8-, 12-, and 16-foot extension tubes for compressed-air garden sprayers were designed and built. These light-weight tubes have been used successfully for spraying white pine leaders for weevil control on the Massabesic Experimental Forest in Maine. Bill of materials and assembly instructions are included.

Life - Past, Present and Future. Environmental Education Curriculum. Revised.

ERIC Educational Resources Information Center

Topeka Public Schools, KS.

This unit attempts to interrelate the traditional biological science studies such as food webs, population changes and ecological succession to form a coherent picture of our world today, the factors that created it and the forces that continue to change it. Designed for use in the secondary schools, it is built around nine films and has seven…

Spacelab: An International Success Story.

ERIC Educational Resources Information Center

Lord, Douglas R.

The Spacelab program was a unique endeavor. For the first time in the history of the United States space effort, the design and development of a major element of a manned space vehicle was entrusted to a foreign agency and to a group of countries which had never before built such a system. This book tells of this cooperative effort between the…

Unique features of a new nickel-hydrogen 2-cell CPV

NASA Technical Reports Server (NTRS)

Wheeler, James R.

1995-01-01

Two-cell nickel-hydrogen common pressure vessel (CPV) units with some unusual design features have been successfully built and tested. The features of interest are half-normal platinum loading for the negative electrodes, the use of rabbit-ear terminals for a CPV unit, and the incorporation of a wall wick. The units have a nominal capacity of 20 Ah and are 3.5 inches in diameter. Electric performance data are provided. The data support the growing viability of the two-cell CPV design concept.

Pathways to policy: Lessons learned in multisectoral collaboration for physical activity and built environment policy development from the Coalitions Linking Action and Science for Prevention (CLASP) initiative.

PubMed

Politis, Christopher E; Mowat, David L; Keen, Deb

2017-06-16

The Canadian Partnership Against Cancer funded 12 large-scale knowledge to action cancer and chronic disease prevention projects between 2009 and 2016 through the Coalitions Linking Action and Science for Prevention (CLASP) initiative. Two projects, Healthy Canada by Design (HCBD) and Children's Mobility, Health and Happiness (CMHH), developed policies to address physical activity and the built environment through a multisectoral approach. A qualitative analysis involving a review of 183 knowledge products and 8 key informant interviews was conducted to understand what policy changes occurred, and the underlying critical success factors, through these projects. Both projects worked at the local level to change physical activity and built environment policy in 203 sites, including municipalities and schools. Both projects brought multisectoral expertise (e.g., public health, land use planning, transportation engineering, education, etc.) together to inform the development of local healthy public policy in the areas of land use, transportation and school travel planning. Through the qualitative analysis of the knowledge products and key informant interviews, 163 policies were attributed to HCBD and CMHH work. Fourteen "pathways to policy" were identified as critical success factors facilitating and accelerating the development and implementation of physical activity and built environment policy. Of the 14 pathways to policy, 8 had a focus on multisectoral collaboration. The lessons learned from the CLASP experience could support enhanced multisectoral collaborations to accelerate the development and implementation of physical activity and built environment policy in new jurisdictions across Canada and internationally.

Dr. Igor Sikorsky Visits the Lewis Flight Propulsion Laboratory

NASA Image and Video Library

1951-06-21

Dr. Igor Sikorsky, fourth from the left, visits the National Advisory Committee for Aeronautics (NACA) Lewis Flight Propulsion Laboratory in Cleveland, Ohio. The legendary Russian-born aviation pioneer visited NACA Lewis several times during the 1940s and 1950s. In 1946 Sikorsky arrived at Lewis for the 1946 National Air Races, which included demonstrations by five of his helicopters. NACA flight mechanic Joseph Sikosky personally escorted Sikorsky during the visit. Sikorsky frequently addressed local professional organizations, such as the American Society of Mechanical Engineers, during his visits. Sikorsky built and flew the first multi-engine aircraft as a youth in Russia. In his mid-20s Sikorsky designed and oversaw the manufacturing of 75 four-engine bombers. During the Bolshevik Revolution he fled to New York City where he worked jobs outside of aviation. In 1923 Sikorsky obtained funding to build a twin-engine water aircraft. This aircraft was the first US twin-engine flying machine and a world-wide success. In 1939 Sikorsky designed the first successful US helicopter. He then put all of his efforts into helicopters, and built some of the most successful helicopters in use today. Sikorsky passed away in 1972. From left to right: unknown; John Collins, Chief of the Engine Performance and Materials Division; Abe Silverstein, Chief of Research; Sikorsky; lab Director Ray Sharp; and Executive Officer Robert Sessions.

The Role of Participatory Design in Mobile Application Development

NASA Astrophysics Data System (ADS)

Hamzah, Almed

2018-03-01

Mobile devices are used by people worldwide. It becomes a common equipment to complete a day-to-day activity. Inside the devices, there are numerous mobile applications that have been built for various needs. Some of these are quite successful while the other are not. The development of successful mobile application faces several challenges. In this research, we want to explore the use of participatory design method in mobile application development. Particularly, the aim of the study is to answer the question whether participatory design method has a place in the realm of mobile application development. We established two sessions of workshop to accommodate the participant to take part in the development process of mobile application. The result shows that participatory design method can determine how the user will deal with the limitations of mobile devices. It helps user to create a particular form of interaction that meets mobile devices characteristics.

Achieving built-environment and active living goals through Music City Moves.

PubMed

Omishakin, Adetokunbo A; Carlat, Jennifer L; Hornsby, Shannon; Buck, Tracy

2009-12-01

Nashville, Tennessee, formed Music City Moves (MCM), an interdisciplinary, countywide partnership to implement its vision for the community: a metropolitan region where routine physical activity is a fundamental part of daily life for all residents. Music City Moves' main focus was the pursuit of changes in community planning policies to help shape Nashville's built environment and facilitate walking and bicycling. To complement this focus, MCM developed a suite of health programs to support physical activity in high-risk populations and a countywide promotional campaign designed to increase awareness and get people active through event participation. Nashville made considerable strides in improving policies and regulations related to building and site design to improve the built environment for pedestrians and cyclists, including passage of (1) specific plan zoning; (2) revised subdivision regulations that introduced a "walkable subdivision" option for developers; and (3) a community-character manual that will guide future land-use planning. Programs and promotions have increased awareness and participation, and the Tour de Nash bike/walk event showcases yearly changes in the built environment. Political leadership has been critical to MCM's success. Leadership of the partnership by the planning department facilitated regulatory changes in planning policies. Music City Moves has accelerated Nashville's movement to improve the built environment and encourage active living. The beneficial impact of policy changes will continue to be manifested in coming years; however, ongoing political support and education of stakeholders in the planning process will be necessary to ensure that planning policies are fully implemented.

Russian Rocket Engine Test

NASA Technical Reports Server (NTRS)

1998-01-01

NASA engineers successfully tested a Russian-built rocket engine on November 4, 1998 at the Marshall Space Flight Center (MSFC) Advanced Engine Test Facility, which had been used for testing the Saturn V F-1 engines and Space Shuttle Main engines. The MSFC was under a Space Act Agreement with Lockheed Martin Astronautics of Denver to provide a series of test firings of the Atlas III propulsion system configured with the Russian-designed RD-180 engine. The tests were designed to measure the performance of the Atlas III propulsion system, which included avionics and propellant tanks and lines, and how these components interacted with the RD-180 engine. The RD-180 is powered by kerosene and liquid oxygen, the same fuel mix used in Saturn rockets. The RD-180, the most powerful rocket engine tested at the MSFC since Saturn rocket tests in the 1960s, generated 860,000 pounds of thrust. The test was the first test ever anywhere outside Russia of a Russian designed and built engine.

A Daytime Aspect Camera for Balloon Altitudes

NASA Technical Reports Server (NTRS)

Dietz, Kurt L.; Ramsey, Brian D.; Alexander, Cheryl D.; Apple, Jeff A.; Ghosh, Kajal K.; Swift, Wesley R.; Six, N. Frank (Technical Monitor)

2001-01-01

We have designed, built, and flight-tested a new star camera for daytime guiding of pointed balloon-borne experiments at altitudes around 40km. The camera and lens are commercially available, off-the-shelf components, but require a custom-built baffle to reduce stray light, especially near the sunlit limb of the balloon. This new camera, which operates in the 600-1000 nm region of the spectrum, successfully provided daytime aspect information of approximately 10 arcsecond resolution for two distinct star fields near the galactic plane. The detected scattered-light backgrounds show good agreement with the Air Force MODTRAN models, but the daytime stellar magnitude limit was lower than expected due to dispersion of red light by the lens. Replacing the commercial lens with a custom-built lens should allow the system to track stars in any arbitrary area of the sky during the daytime.

Rotman lens for mm-wavelengths

NASA Astrophysics Data System (ADS)

Hall, Leonard T.; Hansen, Hedley J.; Abbott, Derek

2002-11-01

The 77 GHz band has been reserved for intelligent cruise control in luxury cars and some public transport services in America and the United Kingdom. The Rotman lens offers a cheap and compact means to extend the single beam systems generally used, to fully functional beam staring arrangements. Rotman lenses have been built for microwave frequencies with limited success. The flexibility of microstrip transmission lines and the advent of fast accurate simulation packages allow practical Rotman lenses to be designed at mm-wavelengths. This paper discusses the limitations of the conventional design approach and predicts the performance of a new Rotman lens designed at 77 GHz.

Design of a flow perfusion bioreactor system for bone tissue-engineering applications.

PubMed

Bancroft, Gregory N; Sikavitsas, Vassilios I; Mikos, Antonios G

2003-06-01

Several different bioreactors have been investigated for tissue-engineering applications. Among these bioreactors are the spinner flask and the rotating wall vessel reactor. In addition, a new type of culture system has been developed and investigated, the flow perfusion culture bioreactor. Flow perfusion culture offers several advantages, notably the ability to mitigate both external and internal diffusional limitations as well as to apply mechanical stress to the cultured cells. For such investigation, a flow perfusion culture system was designed and built. This design is the outgrowth of important design requirements and incorporates features crucial to successful experimentation with such a system.

High Power Silicon Carbide (SiC) Power Processing Unit Development

NASA Technical Reports Server (NTRS)

Scheidegger, Robert J.; Santiago, Walter; Bozak, Karin E.; Pinero, Luis R.; Birchenough, Arthur G.

2015-01-01

NASA GRC successfully designed, built and tested a technology-push power processing unit for electric propulsion applications that utilizes high voltage silicon carbide (SiC) technology. The development specifically addresses the need for high power electronics to enable electric propulsion systems in the 100s of kilowatts. This unit demonstrated how high voltage combined with superior semiconductor components resulted in exceptional converter performance.

Hybrid magnet program at the Francis Bitter National Magnet Laboratory MIT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leupold, M.J.; Weggel, R.J.

1992-01-01

Resistive water-cooled magnets can generate field according to how much power is available. The authors have developed the hybrid concept for generating fields beyond a power limit, up to 45 T. Along the way the authors have progressed through five successively more adventurous designs. This paper chronicles the evolution of hybrid magnets built at the Francis Bitter National Magnet Laboratory.

Planting Trees in Designed and Built Community Landscapes - Checklists for Success

Treesearch

Mary K. Reynolds; H. Sharon Ossenbruggen

Trees create green spaces in communities. The right trees in the right places benefit you, your home, and your community now and in the future. It is essential to select living trees to create a sense of place within communities. This publication helps citizens create community green spaces. It encourages both experts and amateurs to plant and grow trees correctly, and...

Titan/Centaur D-1TTC-5 Helios B flight data report

NASA Technical Reports Server (NTRS)

Adams, K. A.

1976-01-01

The fourth operational flight of the newest NASA unmanned launch vehicle is reported. The spacecraft was the Helios B, the second of two solar probes designed and built by the Federal Republic of Germany. The primary mission objective, to place the Helios spacecraft on a heliocentric orbit in the ecliptic plane with a perihelion distance of 0.29 AU, was successfully accomplished. After successful injection of the Helios spacecraft, a series of experiments were performed with the Centaur stage to demonstrate its operational capabilities. All objectives of the extended mission phase were successfully met. This report presents the analysis of the launch vehicle flight data for the primary mission phase of the TC-5 flight.

Quality by design for herbal drugs: a feedforward control strategy and an approach to define the acceptable ranges of critical quality attributes.

PubMed

Yan, Binjun; Li, Yao; Guo, Zhengtai; Qu, Haibin

2014-01-01

The concept of quality by design (QbD) has been widely accepted and applied in the pharmaceutical manufacturing industry. There are still two key issues to be addressed in the implementation of QbD for herbal drugs. The first issue is the quality variation of herbal raw materials and the second issue is the difficulty in defining the acceptable ranges of critical quality attributes (CQAs). To propose a feedforward control strategy and a method for defining the acceptable ranges of CQAs for the two issues. In the case study of the ethanol precipitation process of Danshen (Radix Salvia miltiorrhiza) injection, regression models linking input material attributes and process parameters to CQAs were built first and an optimisation model for calculating the best process parameters according to the input materials was established. Then, the feasible material space was defined and the acceptable ranges of CQAs for the previous process were determined. In the case study, satisfactory regression models were built with cross-validated regression coefficients (Q(2) ) all above 91 %. The feedforward control strategy was applied successfully to compensate the quality variation of the input materials, which was able to control the CQAs in the 90-110 % ranges of the desired values. In addition, the feasible material space for the ethanol precipitation process was built successfully, which showed the acceptable ranges of the CQAs for the concentration process. The proposed methodology can help to promote the implementation of QbD for herbal drugs. Copyright © 2013 John Wiley & Sons, Ltd.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, a student from AM and his mentor install their payload into the launch vehicle which was built by the team of UAH students. The scientific payload, developed and built by the team of AM students, measured the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, a student from AM and his mentor install their payload into the launch vehicle which was built by the team of UAH students. The scientific payload, developed and built by the team of AM students, measured the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Aircraft Accident Investigation at ARL: The First 50 Years

DTIC Science & Technology

1993-03-01

monoplane with vee strut bracing. Designed by De Havillands as the DH . 80A, it proved highly successful; two hundred and sixty were built in the UK...3 4. THE PUSS MOTH ACCIDENTS ............................................................ 5 5. THE DH .86 ACCIDENTS...Melbourne and just as the royal procession was turning from St Kilda Road into the grounds of Government House, two DH .9 aircraft of the RAAF flypast collided

Fiber pulling apparatus modification

NASA Technical Reports Server (NTRS)

Smith, Guy A.; Workman, Gary L.

1992-01-01

A reduced gravity fiber pulling apparatus (FPA) was constructed in order to study the effects of gravity on glass fiber formation. The apparatus was specifically designed and built for use on NASA's KC-135 aircraft. Four flights have been completed to date during which E-glass fiber was successfully produced in simulated zero, high, and lunar gravity environments. In addition simulated lunar soil samples were tested for their fiber producing properties using the FPA.

Optimally designed gold nanorattles with strong built-in hotspots and weak polarization dependence

NASA Astrophysics Data System (ADS)

Zhang, Xuemin; Wang, Tieqiang; Li, Yunong; Fu, Yu; Guo, Lei

2017-12-01

Localized electromagnetic fields generated by interparticle plasmon coupling suffer greatly from nonreproducibility because they are extremely sensitive to the nanoparticle aggregation status and the incident polarization. Here, we synthesize gold nanorattles that exhibit inherent aggregation-insensitive hotspots due to the intraparticle core-shell plasmon coupling, and investigate the structural effect on the intraparticle coupling strength and its polarization dependence. Through optimizing the structural parameters, we successfully synthesize gold nanorattles with strong built-in hotspots and weak polarization dependence. These aggregation-insensitive and weakly polarization-dependent hotspots make the Raman enhancement from nanorattle aggregates show an unusual weak dependence on the particle aggregation status, which therefore affords the opportunity to fabricate uniform and reproducible surface enhanced Raman scattering substrates.

The deaf and the classroom design: a contribution of the built environmental ergonomics for the accessibility.

PubMed

Martins, Laura Bezerra; Gaudiot, Denise Mariasimões Freire

2012-01-01

In any concept of school design, classroom occupies the central place. Dimensions, lighting, the equipment needed, ventilation are old questions already answered, even in form of laws and standards adopted. However, the best use of available materials and physical conditions of comfort is not sufficient for a classroom design guaranteed success. The classroom should provide deaf students elements to facilitate the learning process, eliminating as much as possible the obstacles created by lack of hearing and allowing them to have the same access to learning as a listener student. As users of a school building, teachers, students, parents and staff are the best evaluators of the physical environment of schools. The environmental comfort is a largest ally of pedagogy. The learning comes from the perception and the concentration of students in the classroom. The purpose of this study is to detect the role of direct perception (physical) and indirect (intangible) elements that informs and have symbolic value, and propose layouts for accessible classrooms to deaf students. The ergonomics of the built environment evaluation methods could use the participatory design method tools as basis to assessing how users perceive and use the school environment.

Mission Management Computer Software for RLV-TD

NASA Astrophysics Data System (ADS)

Manju, C. R.; Joy, Josna Susan; Vidya, L.; Sheenarani, I.; Sruthy, C. N.; Viswanathan, P. C.; Dinesh, Sudin; Jayalekshmy, L.; Karuturi, Kesavabrahmaji; Sheema, E.; Syamala, S.; Unnikrishnan, S. Manju; Ali, S. Akbar; Paramasivam, R.; Sheela, D. S.; Shukkoor, A. Abdul; Lalithambika, V. R.; Mookiah, T.

2017-12-01

The Mission Management Computer (MMC) software is responsible for the autonomous navigation, sequencing, guidance and control of the Re-usable Launch Vehicle (RLV), through lift-off, ascent, coasting, re-entry, controlled descent and splashdown. A hard real-time system has been designed for handling the mission requirements in an integrated manner and for meeting the stringent timing constraints. Redundancy management and fault-tolerance techniques are also built into the system, in order to achieve a successful mission even in presence of component failures. This paper describes the functions and features of the components of the MMC software which has accomplished the successful RLV-Technology Demonstrator mission.

Self-Reconfigurable Robots

DOE Office of Scientific and Technical Information (OSTI.GOV)

HENSINGER, DAVID M.; JOHNSTON, GABRIEL A.; HINMAN-SWEENEY, ELAINE M.

2002-10-01

A distributed reconfigurable micro-robotic system is a collection of unlimited numbers of distributed small, homogeneous robots designed to autonomously organize and reorganize in order to achieve mission-specified geometric shapes and functions. This project investigated the design, control, and planning issues for self-configuring and self-organizing robots. In the 2D space a system consisting of two robots was prototyped and successfully displayed automatic docking/undocking to operate dependently or independently. Additional modules were constructed to display the usefulness of a self-configuring system in various situations. In 3D a self-reconfiguring robot system of 4 identical modules was built. Each module connects to its neighborsmore » using rotating actuators. An individual component can move in three dimensions on its neighbors. We have also built a self-reconfiguring robot system consisting of 9-module Crystalline Robot. Each module in this robot is actuated by expansion/contraction. The system is fully distributed, has local communication (to neighbors) capabilities and it has global sensing capabilities.« less

Measuring the food and built environments in urban centres: reliability and validity of the EURO-PREVOB Community Questionnaire.

PubMed

Pomerleau, J; Knai, C; Foster, C; Rutter, H; Darmon, N; Derflerova Brazdova, Z; Hadziomeragic, A F; Pekcan, G; Pudule, I; Robertson, A; Brunner, E; Suhrcke, M; Gabrijelcic Blenkus, M; Lhotska, L; Maiani, G; Mistura, L; Lobstein, T; Martin, B W; Elinder, L S; Logstrup, S; Racioppi, F; McKee, M

2013-03-01

The authors designed an instrument to measure objectively aspects of the built and food environments in urban areas, the EURO-PREVOB Community Questionnaire, within the EU-funded project 'Tackling the social and economic determinants of nutrition and physical activity for the prevention of obesity across Europe' (EURO-PREVOB). This paper describes its development, reliability, validity, feasibility and relevance to public health and obesity research. The Community Questionnaire is designed to measure key aspects of the food and built environments in urban areas of varying levels of affluence or deprivation, within different countries. The questionnaire assesses (1) the food environment and (2) the built environment. Pilot tests of the EURO-PREVOB Community Questionnaire were conducted in five to 10 purposively sampled urban areas of different socio-economic status in each of Ankara, Brno, Marseille, Riga, and Sarajevo. Inter-rater reliability was compared between two pairs of fieldworkers in each city centre using three methods: inter-observer agreement (IOA), kappa statistics, and intraclass correlation coefficients (ICCs). Data were collected successfully in all five cities. Overall reliability of the EURO-PREVOB Community Questionnaire was excellent (inter-observer agreement (IOA) > 0.87; intraclass correlation coefficients (ICC)s > 0.91 and kappa statistics > 0.7. However, assessment of certain aspects of the quality of the built environment yielded slightly lower IOA coefficients than the quantitative aspects. The EURO-PREVOB Community Questionnaire was found to be a reliable and practical observational tool for measuring differences in community-level data on environmental factors that can impact on dietary intake and physical activity. The next step is to evaluate its predictive power by collecting behavioural and anthropometric data relevant to obesity and its determinants. Copyright © 2013 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Design component method for sensitivity analysis of built-up structures

NASA Technical Reports Server (NTRS)

Choi, Kyung K.; Seong, Hwai G.

1986-01-01

A 'design component method' that provides a unified and systematic organization of design sensitivity analysis for built-up structures is developed and implemented. Both conventional design variables, such as thickness and cross-sectional area, and shape design variables of components of built-up structures are considered. It is shown that design of components of built-up structures can be characterized and system design sensitivity expressions obtained by simply adding contributions from each component. The method leads to a systematic organization of computations for design sensitivity analysis that is similar to the way in which computations are organized within a finite element code.

Quasi-perfect FIFO: Synchronous or asynchronous with application in controller design for the UNICON laser memory. [digital memory and buffer storage

NASA Technical Reports Server (NTRS)

Lim, R. S.

1974-01-01

The first-in-first-out memory buffer (FIFO), is an elastic digital memory whose main application is in data buffering between devices operating at different rates. Data written into the top is moved autonomously down toward the bottom of the FIFO to the lowest unoccupied location, and data read from the bottom of the FIFO will cause data from the top to move autonomously down toward the bottom. The FIFO is available in MOS LSI asynchronous form with data rate in the 1 MHz region. The FIFO described yields a simple high-speed iterative implementation, either synchronous of asynchronous. Because of this simple iterative structure, the FIFO is expandable in both number of words and bits per word, and it is attractive from the viewpoint of integrated-circuit production. For the synchronous FIFO, a model was built and successfully used in the controller for the UNICON laser memory. For the asynchronous FIFO, a model was built and also successfully used in a high-performance magnetic tape controller.

Thermal effects in the Input Optics of the Enhanced Laser Interferometer Gravitational-Wave Observatory interferometers.

PubMed

Dooley, Katherine L; Arain, Muzammil A; Feldbaum, David; Frolov, Valery V; Heintze, Matthew; Hoak, Daniel; Khazanov, Efim A; Lucianetti, Antonio; Martin, Rodica M; Mueller, Guido; Palashov, Oleg; Quetschke, Volker; Reitze, David H; Savage, R L; Tanner, D B; Williams, Luke F; Wu, Wan

2012-03-01

We present the design and performance of the LIGO Input Optics subsystem as implemented for the sixth science run of the LIGO interferometers. The Initial LIGO Input Optics experienced thermal side effects when operating with 7 W input power. We designed, built, and implemented improved versions of the Input Optics for Enhanced LIGO, an incremental upgrade to the Initial LIGO interferometers, designed to run with 30 W input power. At four times the power of Initial LIGO, the Enhanced LIGO Input Optics demonstrated improved performance including better optical isolation, less thermal drift, minimal thermal lensing, and higher optical efficiency. The success of the Input Optics design fosters confidence for its ability to perform well in Advanced LIGO.

A 100 J-level nanosecond DPSSL for high energy density experiments

NASA Astrophysics Data System (ADS)

Butcher, Thomas; Mason, Paul; Banerjee, Saumyabrata; Ertel, Klaus; Phillips, P. Jonathan; Smith, Jodie; De Vido, Mariastefania; Chekhlov, Oleg; Divoky, Martin; Pilat, Jan; Priebe, Gerd; Toncian, Toma; Shaikh, Waseem; Hooker, Chris; Lucianetti, Antonio; Hernandez-Gomez, Cristina; Mocek, Tomas; Edwards, Chris; Collier, John

2017-05-01

We present an overview of the cryo-amplifier concept and design utilized in the DiPOLE100 laser system built for use at the HiLASE Center, which has been successfully tested operating at an average power of 1kW. Following this we describe the alterations made to the design in the second generation system being constructed for high energy density (HED) experiments in the HED beamline at the European XFEL. These changes are predominantly geometric in nature, however also include improved mount design and improved control over the temporal shape of the output pulse. Finally, we comment on future plans for development of the DiPOLE laser amplifier architecture.

Design and Testing of a Transcutaneous RF Recharging System for a Fetal Micropacemaker.

PubMed

Vest, Adriana N; Zhou, Li; Huang, Xuechen; Norekyan, Viktoria; Bar-Cohen, Yaniv; Chmait, Ramen H; Loeb, Gerald Eli

2017-04-01

We have developed a rechargeable fetal micropacemaker in order to treat severe fetal bradycardia with comorbid hydrops fetalis. The necessarily small form factor of the device, small patient population, and fetal anatomy put unique constraints on the design of the recharging system. To overcome these constraints, a custom high power field generator was built and the recharging process was controlled by utilizing pacing rate as a measure of battery state, a feature of the relaxation oscillator used to generate stimuli. The design and in vitro and in vivo verification of the recharging system is presented here, showing successful generation of recharging current in a fetal lamb model.

Design and Testing of a Transcutaneous RF Recharging System for a Fetal Micropacemaker

PubMed Central

Vest, Adriana N.; Zhou, Li; Huang, Xuechen; Norekyan, Viktoria; Bar-Cohen, Yaniv; Chmait, Ramen H.; Loeb, Gerald Eli

2017-01-01

We have developed a rechargeable fetal micropacemaker in order to treat severe fetal bradycardia with comorbid hydrops fetalis. The necessarily small form factor of the device, small patient population, and fetal anatomy put unique constraints on the design of the recharging system. To overcome these constraints, a custom high power field generator was built and the recharging process was controlled by utilizing pacing rate as a measure of battery state, a feature of the relaxation oscillator used to generate stimuli. The design and in vitro and in vivo verification of the recharging system is presented here, showing successful generation of recharging current in a fetal lamb model. PMID:28212097

Low-Cost Approach to the Design and Fabrication of a LOX/RP-1 Injector

NASA Technical Reports Server (NTRS)

Shadoan, Michael D.; Sparks, Dave L.; Turner, James E. (Technical Monitor)

2000-01-01

NASA Marshall Space Flight Center (MSFC) has designed, built, and is currently testing Fastrac, a liquid oxygen (LOX)/RP-1 fueled 60K-lb thrust class rocket engine. One facet of Fastrac, which makes it unique is that it is the first large-scale engine designed and developed in accordance with the Agency's mandated "faster, better, cheaper" (FBC) program policy. The engine was developed under the auspices of MSFC's Low Cost Boost Technology office. Development work for the main injector actually began in 1993 in subscale form. In 1996, work began on the full-scale unit approximately 1 year prior to initiation of the engine development program. In order to achieve the value goals established by the FBC policy, a review of traditional design practices was necessary. This internal reevaluation would ultimately challenge more conventional methods of material selection. design process, and fabrication techniques. The effort was highly successful. This "new way" of thinking has resulted in an innovative injector design, one with reduced complexity and significantly lower cost. Application of lessons learned during this effort to new or existing designs can have a similar effect on costs and future program successes.

Childcare outdoor renovation as a built environment health promotion strategy: evaluating the preventing obesity by design intervention.

PubMed

Cosco, Nilda G; Moore, Robin C; Smith, William R

2014-01-01

To evaluate the effectiveness of Preventing Obesity by Design (POD), a childcare center outdoor renovation intervention. Pre-post intervention evaluation. North Carolina licensed childcare centers (N = 27). Preschool children. Outdoor renovation, teacher training. Behavior mapping, Preschool Outdoor Environment Measurement Scale (POEMS), center director interview. Descriptive statistics, ordinary least squares and logistic regressions calculated to assess levels of association between environmental change, children's physical activity (PA), social behaviors, and environmental quality. Qualitative interview data analyzed to help understand intervention impact. Behavior mapping showed that site layout attributes, such as the form (i.e., "single loop" and "double loop") of pathways (functioning as circulation routes and wheeled toy settings), are associated with higher levels of PA. Teacher interaction was associated with decreased children's PA. Absence of teacher or lack of child/child interaction was associated with increased PA. POEMS assessment of environmental quality was higher after renovation. POEMS domains (Physical Space and Teacher/Caregiver Roles) were positively associated with PA. After renovation, 68% of center directors reported positive changes in children's behavior and 40% mentioned edible plant installations as greatest success. Built environment renovation of childcare center outdoors, including looped pathways installation, coupled with teacher training, may support increased PA. Renovation, including food gardens, may be a key to success for preschool health promotion and support change in childcare policy.

United Space Alliance, LLC Windchill As-Built Highlights

NASA Technical Reports Server (NTRS)

Richmond, Dena M.

2011-01-01

Work Order execution data from Solumina As Worked BOM (As-Built) in Solumina (Slide 2) sent to Windchill Windchill receives As Worked BOM data and 'marries' the Solumina execution data to the Part Instance/Product Structure/As-Design (Slide 3 As-Design and Slide 4 &5 As-Built) Manage the As-Built to As-Design delta's via the interface and Part Instance Attributes (Slide 6) including Work Order data and any CMcomments Produce an As-Built to As-Design report that also includes all Part Instance Attribute data (no screenshot as this is still in development) Utilize Windchill and Solumina 'Out of the Box' functionality

Predictors of Study Success from a Teacher's Perspective of the Quality of the Built Environment

ERIC Educational Resources Information Center

Kok, Herman; Mobach, Mark; Omta, Onno

2015-01-01

The article aims to find predictors of study success from a teacher's perspective that relate to the built environment. The research is based on a national online survey among 1752 teachers at 18 Dutch Universities of Applied Sciences. Multivariate data analyses were used to test the hypothesis that the quality of spatial and functional aspects at…

FSW of Aluminum Tailor Welded Blanks across Machine Platforms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanski, Yuri; Upadhyay, Piyush; Carlson, Blair

2015-02-16

Development and characterization of friction stir welded aluminum tailor welded blanks was successfully carried out on three separate machine platforms. Each was a commercially available, gantry style, multi-axis machine designed specifically for friction stir welding. Weld parameters were developed to support high volume production of dissimilar thickness aluminum tailor welded blanks at speeds of 3 m/min and greater. Parameters originally developed on an ultra-high stiffness servo driven machine where first transferred to a high stiffness servo-hydraulic friction stir welding machine, and subsequently transferred to a purpose built machine designed to accommodate thin sheet aluminum welding. The inherent beam stiffness, bearingmore » compliance, and control system for each machine were distinctly unique, which posed specific challenges in transferring welding parameters across machine platforms. This work documents the challenges imposed by successfully transferring weld parameters from machine to machine, produced from different manufacturers and with unique control systems and interfaces.« less

Formation of Carbon Nanotubes in a Microgravity Environment

NASA Technical Reports Server (NTRS)

Alford, J. M.; Mason, G. R.; Feikema, D. A.

2001-01-01

Even though nanotube science has become one of the worlds most rapidly advancing areas of research, very little is known about the processes involved in nanotube synthesis. To study the formation of carbon nanotubes in an environment unhindered by the buoyancy induced flows generated by the high temperatures necessary to vaporize carbon and grow nanotubes, we have designed a miniature carbon arc apparatus that can produce carbon nanotubes under microgravity conditions. During the first phase of this project, we designed, built, and successfully tested the mini carbon arc in both 1g and 2.2 sec drop tower microgravity conditions. We have demonstrated that microgravity can eliminate the strong convective flows from the carbon arc and we have successfully produced single-walled carbon nanotubes in microgravity. We believe that microgravity processing will allow us to better understand the nanotube formation process and eventually allow us to grow nanotubes that are superior to ground-based production.

Electro-optic product design for manufacture: where next?

NASA Astrophysics Data System (ADS)

Barr, John R. M.; MacDonald, M.; Jeffery, G.; Troughton, M.

2016-10-01

Manufacturing of electro-optic products for military environments poses a large number of apparently intractable and mutually contradictory problems. The ability to successfully engage in this area presents an intellectual challenge of a high order. The Advanced Targeting Sector of Leonardo's Airborne and Space Systems Division, based in Edinburgh, has developed a successful range of electro-optic products and transitioned these into a volume, and high value, manufacturing environment. As products cycle through the design process, there has been strong feedback from users, suppliers, and most importantly from our manufacturing organization, that has driven evolution of our design practices. It is fair to say that recent pointer trackers and lasers bear little resemblance to those designed and built 10 years ago. Looking ahead, this process will only continue. There are interesting technologies that will drive improvements in manufacturability, reliability and usability of electro-optic products. Examples might include freeform optics, additive manufacture of metal components, and laser welding of optics to metals, to name but a few. These have uses across our product portfolio and, when sufficiently matured, will have a major impact on the product quality and reliability

Teaching Creative Thinking through Architectural Design

ERIC Educational Resources Information Center

Jeon, Kijeong; Cotner, Teresa L.

2010-01-01

Art and art education are open to broader definitions in the twenty-first century. It is time that teachers seriously think about including built environment design in K-12 art education. The term "built environment" includes interior design, architecture, landscape architecture, and urban planning. Due to increased exposure to built environment…

The Brothers Were Wright - An Abridged History of Wind Tunnel Testing at Ames Research Center

NASA Technical Reports Server (NTRS)

Buchholz, Steve

2017-01-01

The Wright Brothers used wind tunnel data to refine their design for the first successful airplane back in 1903. Today, wind tunnels are still in use all over the world gathering data to improve the design of cars, trucks, airplanes, missiles and spacecraft. Ames Research Center is home to many wind tunnels, including the Unitary Plan Wind Tunnel complex. Built in the early 1950s, it is one of the premiere transonic and supersonic testing facilities in the country. Every manned spacecraft has been tested in the wind tunnels at Ames. This is a testing history from past to present.

Effects of environmental design on patient outcome: a systematic review.

PubMed

Laursen, Jannie; Danielsen, Anne; Rosenberg, Jacob

2014-01-01

The aim of this systematic review was to assess how inpatients were affected by the built environment design during their hospitalization. Over the last decade, the healthcare system has become increasingly aware of how focus on healthcare environment might affect patient satisfaction. The focus on environmental design has become a field with great potential because of its possible impact on cost control while improving quality of care. A systematic literature search was conducted to identify current and past studies about evidence-based healthcare design. The following databases were searched: Medline/PubMed, Cinahl, and Embase. Inclusion criteria were randomized clinical trials (RCTs) investigating the effect of built environment design interventions such as music, natural murals, and plants in relation to patients' health outcome. Built environment design aspects such as audio environment and visual environment had a positive influence on patients' health outcomes. Specifically the studies indicated a decrease in patients' anxiety, pain, and stress levels when exposed to certain built environment design interventions. The built environment, especially specific audio and visual aspects, seems to play an important role in patients' outcomes, making hospitals a better healing environment for patients. Built environment, evidence-based design, healing environments, hospitals, literature review.

Genesis of a flexible turning center

NASA Astrophysics Data System (ADS)

Sanclemente, Paul; French, Robert D.

GE - Aircraft Engines has designed, built, and is operating a flexible turning center for jet engine hardware. Although the plant is in the forefront of manufacturing technology development, it was intended from the start to be a production facility. So while there was much to learn from being involved in all phases of the project, meeting production schedules was, and is, key to its success. This paper reviews the early history of the project and ends with a view of its recent production status.

Compensatory stream and wetland mitigation in North Carolina: an evaluation of regulatory success.

PubMed

Hill, Tammy; Kulz, Eric; Munoz, Breda; Dorney, John R

2013-05-01

Data from a probability sample were used to estimate wetland and stream mitigation success from 2007 to 2009 across North Carolina (NC). "Success" was defined as whether the mitigation site met regulatory requirements in place at the time of construction. Analytical results were weighted by both component counts and mitigation size. Overall mitigation success (including preservation) was estimated at 74 % (SE = 3 %) for wetlands and 75 % (SE = 4 %) for streams in NC. Compared to the results of previous studies, wetland mitigation success rates had increased since the mid-1990s. Differences between mitigation providers (mitigation banks, NC Ecosystem Enhancement Program's design-bid-build and full-delivery programs, NC Department of Transportation and private permittee-responsible mitigation) were generally not significant although permittee-responsible mitigation yielded higher success rates in certain circumstances. Both wetland and stream preservation showed high rates of success and the stream enhancement success rate was significantly higher than that of stream restoration. Additional statistically significant differences when mitigation size was considered included: (1) the Piedmont yielded a lower stream mitigation success rate than other areas of the state, and (2) recently constructed wetland mitigation projects demonstrated a lower success rate than those built prior to 2002. Opportunities for improvement exist in the areas of regulatory record-keeping, understanding the relationship between post-construction establishment and long-term ecological trajectories of stream and wetland restoration projects, incorporation of numeric ecological metrics into mitigation monitoring and success criteria, and adaptation of stream mitigation designs to achieve greater success in the Piedmont.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from three Huntsville area high schools: Randolph, Sparkman, and Johnson High Schools, counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides them with hands-on, practical aerospace experience. In this picture, three Sparkman High School students pose with their rocket.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from three Huntsville area high schools: Randolph, Sparkman and Johnson High Schools, counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides them with hands-on, practical aerospace experience. In this picture, two Johnson High School students pose with their rocket.

Around Marshall

NASA Image and Video Library

2002-04-27

Filled with anticipation, students from three Huntsville area high schools: Randolph, Sparkman, and Johnson High Schools, counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides them with hands-on, practical aerospace experience. In this picture, three Sparkman High School students pose with their rocket.

Around Marshall

NASA Image and Video Library

2002-04-27

Filled with anticipation, students from three Huntsville area high schools: Randolph, Sparkman and Johnson High Schools, counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides them with hands-on, practical aerospace experience. In this picture, two Johnson High School students pose with their rocket.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the combined efforts of students from UAH and AM sent this rocket soaring into flight. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) Program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the university students prepare their rocket for flight on the launch pad. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the University students prepare their rocket for launch. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the University students prepare their rocket for launch. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-23

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the combined efforts of students from UAH and AM sent this rocket soaring into flight. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Around Marshall

NASA Image and Video Library

2002-05-22

Filled with anticipation, students from two local universities, the University of Alabama in Huntsville (UAH), and Alabama Agricultural Mechanical University (AM), counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) Program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides the students with hands-on, practical aerospace experience. In this picture, the university students prepare their rocket for flight on the launch pad. Students at UAH built the rocket and AM students developed its scientific payload, an experiment that measures the amount of hydrogen produced during electroplating with nickel in a brief period of micrgravity.

Design and implementation of dynamic hybrid Honeypot network

NASA Astrophysics Data System (ADS)

Qiao, Peili; Hu, Shan-Shan; Zhai, Ji-Qiang

2013-05-01

The method of constructing a dynamic and self-adaptive virtual network is suggested to puzzle adversaries, delay and divert attacks, exhaust attacker resources and collect attacking information. The concepts of Honeypot and Honeyd, which is the frame of virtual Honeypot are introduced. The techniques of network scanning including active fingerprint recognition are analyzed. Dynamic virtual network system is designed and implemented. A virtual network similar to real network topology is built according to the collected messages from real environments in this system. By doing this, the system can perplex the attackers when Hackers attack and can further analyze and research the attacks. The tests to this system prove that this design can successfully simulate real network environment and can be used in network security analysis.

The Magnetospheric Multiscale Magnetometers

NASA Technical Reports Server (NTRS)

Russell, C. T.; Anderson, B. J.; Baumjohann, W.; Bromund, K. R.; Dearborn, D.; Fischer, D.; Le, G.; Leinweber, H. K.; Leneman, D.; Magnes, W.;

DREAMS and IMAGE: A Model and Computer Implementation for Concurrent, Life-Cycle Design of Complex Systems

NASA Technical Reports Server (NTRS)

Hale, Mark A.; Craig, James I.; Mistree, Farrokh; Schrage, Daniel P.

1995-01-01

Computing architectures are being assembled that extend concurrent engineering practices by providing more efficient execution and collaboration on distributed, heterogeneous computing networks. Built on the successes of initial architectures, requirements for a next-generation design computing infrastructure can be developed. These requirements concentrate on those needed by a designer in decision-making processes from product conception to recycling and can be categorized in two areas: design process and design information management. A designer both designs and executes design processes throughout design time to achieve better product and process capabilities while expanding fewer resources. In order to accomplish this, information, or more appropriately design knowledge, needs to be adequately managed during product and process decomposition as well as recomposition. A foundation has been laid that captures these requirements in a design architecture called DREAMS (Developing Robust Engineering Analysis Models and Specifications). In addition, a computing infrastructure, called IMAGE (Intelligent Multidisciplinary Aircraft Generation Environment), is being developed that satisfies design requirements defined in DREAMS and incorporates enabling computational technologies.

Dizeez: An Online Game for Human Gene-Disease Annotation

PubMed Central

Loguercio, Salvatore; Good, Benjamin M.; Su, Andrew I.

2013-01-01

Structured gene annotations are a foundation upon which many bioinformatics and statistical analyses are built. However the structured annotations available in public databases are a sparse representation of biological knowledge as a whole. The rate of biomedical data generation is such that centralized biocuration efforts struggle to keep up. New models for gene annotation need to be explored that expand the pace at which we are able to structure biomedical knowledge. Recently, online games have emerged as an effective way to recruit, engage and organize large numbers of volunteers to help address difficult biological challenges. For example, games have been successfully developed for protein folding (Foldit), multiple sequence alignment (Phylo) and RNA structure design (EteRNA). Here we present Dizeez, a simple online game built with the purpose of structuring knowledge of gene-disease associations. Preliminary results from game play online and at scientific conferences suggest that Dizeez is producing valid gene-disease annotations not yet present in any public database. These early results provide a basic proof of principle that online games can be successfully applied to the challenge of gene annotation. Dizeez is available at http://genegames.org. PMID:23951102

Design of a tracked ultrasound calibration phantom made of LEGO bricks

NASA Astrophysics Data System (ADS)

Walsh, Ryan; Soehl, Marie; Rankin, Adam; Lasso, Andras; Fichtinger, Gabor

2014-03-01

PURPOSE: Spatial calibration of tracked ultrasound systems is commonly performed using precisely fabricated phantoms. Machining or 3D printing has relatively high cost and not easily available. Moreover, the possibilities for modifying the phantoms are very limited. Our goal was to find a method to construct a calibration phantom from affordable, widely available components, which can be built in short time, can be easily modified, and provides comparable accuracy to the existing solutions. METHODS: We designed an N-wire calibration phantom made of LEGO® bricks. To affirm the phantom's reproducibility and build time, ten builds were done by first-time users. The phantoms were used for a tracked ultrasound calibration by an experienced user. The success of each user's build was determined by the lowest root mean square (RMS) wire reprojection error of three calibrations. The accuracy and variance of calibrations were evaluated for the calibrations produced for various tracked ultrasound probes. The proposed model was compared to two of the currently available phantom models for both electromagnetic and optical tracking. RESULTS: The phantom was successfully built by all ten first-time users in an average time of 18.8 minutes. It cost approximately $10 CAD for the required LEGO® bricks and averaged a 0.69mm of error in the calibration reproducibility for ultrasound calibrations. It is one third the cost of similar 3D printed phantoms and takes much less time to build. The proposed phantom's image reprojections were 0.13mm more erroneous than those of the highest performing current phantom model The average standard deviation of multiple 3D image reprojections differed by 0.05mm between the phantoms CONCLUSION: It was found that the phantom could be built in less time, was one third the cost, compared to similar 3D printed models. The proposed phantom was found to be capable of producing equivalent calibrations to 3D printed phantoms.

Commuting Mode Choice in a High-Density City: Do Land-Use Density and Diversity Matter in Hong Kong?

PubMed Central

Sun, Guibo; Sarkar, Chinmoy; Xiao, Yang

2018-01-01

Hong Kong is a densely populated and transit-oriented Chinese city, which provides an ideal urban environment with which to study the various successful facets of land use policy as a model for potential replication to curb increasing car use in other Chinese cities. We examine the commuting mode choice of 203,900 households living in 4768 street blocks in Hong Kong from 2011 census. A street block is the smallest planning unit, made up of one or more housing estates with a homogenous built environment and socioeconomic status. The built environment is measured using the five Ds framework, an international dimensioning framework for classifying and measuring attributes of the built environment for physical activity and travel behaviors. Generalized, multi-level mixed models were applied to detect the associations between travel choice and built environment characteristics, while adjusting for socioeconomic status. Design and destination accessibility had greater effects on the choices to walk and take public transport than on the choice to drive. Density and diversity had only marginal effects on mode choice. Unexpectedly, distance to the urban center had the opposite effect on automobile use to that found in Western studies. Hong Kong residents living close to the urban center were more likely to drive for commuting trips. The contrasting findings between our study and Western studies suggest that the associations between a high-density built environment and travel choice vary with urban context. PMID:29734721

Ultimately Reliable Pyrotechnic Systems

NASA Technical Reports Server (NTRS)

Scott, John H.; Hinkel, Todd

2015-01-01

This paper presents the methods by which NASA has designed, built, tested, and certified pyrotechnic devices for high reliability operation in extreme environments and illustrates the potential applications in the oil and gas industry. NASA's extremely successful application of pyrotechnics is built upon documented procedures and test methods that have been maintained and developed since the Apollo Program. Standards are managed and rigorously enforced for performance margins, redundancy, lot sampling, and personnel safety. The pyrotechnics utilized in spacecraft include such devices as small initiators and detonators with the power of a shotgun shell, detonating cord systems for explosive energy transfer across many feet, precision linear shaped charges for breaking structural membranes, and booster charges to actuate valves and pistons. NASA's pyrotechnics program is one of the more successful in the history of Human Spaceflight. No pyrotechnic device developed in accordance with NASA's Human Spaceflight standards has ever failed in flight use. NASA's pyrotechnic initiators work reliably in temperatures as low as -420 F. Each of the 135 Space Shuttle flights fired 102 of these initiators, some setting off multiple pyrotechnic devices, with never a failure. The recent landing on Mars of the Opportunity rover fired 174 of NASA's pyrotechnic initiators to complete the famous '7 minutes of terror.' Even after traveling through extreme radiation and thermal environments on the way to Mars, every one of them worked. These initiators have fired on the surface of Titan. NASA's design controls, procedures, and processes produce the most reliable pyrotechnics in the world. Application of pyrotechnics designed and procured in this manner could enable the energy industry's emergency equipment, such as shutoff valves and deep-sea blowout preventers, to be left in place for years in extreme environments and still be relied upon to function when needed, thus greatly enhancing safety and operational availability.

Hydroxyapatite implants with designed internal architecture.

PubMed

Chu, T M; Halloran, J W; Hollister, S J; Feinberg, S E

2001-06-01

Porous hydroxyapatite (HA) has been used as a bone graft material in the clinics for decades. Traditionally, the pores in these HAs are either obtained from the coralline exoskeletal patterns or from the embedded organic particles in the starting HA powder. Both processes offer very limited control on the pore structure. A new method for manufacturing porous HA with designed pore channels has been developed. This method is essentially a lost-mold technique with negative molds made with Stereolithography and a highly loaded curable HA suspension as the ceramic carrier. Implants with designed channels and connection patterns were first generated from a Computer-Aided-Design (CAD) software and Computer Tomography (CT) data. The negative images of the designs were used to build the molds on a stereolithography apparatus with epoxy resins. A 40 vol% HA suspension in propoxylated neopentyl glycol diacrylate (PNPGDA) and iso-bornyl acrylate (IBA) was formulated. HA suspension was cast into the epoxy molds and cured into solid at 85 degrees C. The molds and acrylate binders were removed by pyrolysis, followed by HA green body sintering. With this method, implants with six different channel designs were built successfully and the designed channels were reproduced in the sintered HA implants. The channels created in the sintered HA implants were between 366 microm and 968 microm in diameter with standard deviations of 50 microm or less. The porosity created by the channels were between 26% and 52%. The results show that HA implants with designed connection pattern and well controlled channel size can be built with the technique developed in this study. Copyright 2001 Kluwer Academic Publishers

Students Participate in Rocket Launch Project

NASA Technical Reports Server (NTRS)

2002-01-01

Filled with anticipation, students from three Huntsville area high schools: Randolph, Sparkman, and Johnson High Schools, counted down to launch the rockets they designed and built at the Army test site on Redstone Arsenal in Huntsville, Alabama. The projected two-mile high launch culminated more than a year's work and demonstrated the student team's ability to meet the challenge set by the Marshall Space Flight Center's (MSFC) Student Launch Initiative (SLI) program to apply science and math to experience, judgment, and common sense, and proved to NASA officials that they have successfully built reusable launch vehicles (RLVs), another challenge set by NASA's SLI program. MSFC's SLI program is an educational effort that aims to motivate students to pursue careers in science, math, and engineering. It provides hands-on, practical aerospace experience. In this picture, Randolph High School students are assembling their rocket in preparation for launch.

A synthetic mammalian electro-genetic transcription circuit.

PubMed

Weber, Wilfried; Luzi, Stefan; Karlsson, Maria; Sanchez-Bustamante, Carlota Diaz; Frey, Urs; Hierlemann, Andreas; Fussenegger, Martin

2009-03-01

Electric signal processing has evolved to manage rapid information transfer in neuronal networks and muscular contraction in multicellular organisms and controls the most sophisticated man-built devices. Using a synthetic biology approach to assemble electronic parts with genetic control units engineered into mammalian cells, we designed an electric power-adjustable transcription control circuit able to integrate the intensity of a direct current over time, to translate the amplitude or frequency of an alternating current into an adjustable genetic readout or to modulate the beating frequency of primary heart cells. Successful miniaturization of the electro-genetic devices may pave the way for the design of novel hybrid electro-genetic implants assembled from electronic and genetic parts.

High Output Maximum Efficiency Resonator (HOMER) Laser for NASA's Global Ecosystem Dynamics Investigation (GEDI) Lidar Mission

NASA Technical Reports Server (NTRS)

Stysley, Paul; Coyle, Barry; Clarke, Greg; Poulios, Demetrios; Kay, Richard

2015-01-01

The Global Ecosystems Dynamics Investigation (GEDI) is a planned mission sending a LIDAR instrument to the International Space Station that will employ three NASA laser transmitters. This instrument will produce parallel tracks on the Earth's surface that will provide global 3D vegetation canopy measurements. To meet the mission goals a total of 5 High Output Maximum Efficiency Resonator lasers will to be built (1 ETU + 3 Flight + 1 spare) in-house at NASA-GSFC. This presentation will summarize the HOMER design, the testing the design has completed in the past, and the plans to successfully build the units needed for the GEDI mission.

Final prototype of magnetically suspended flywheel energy storage system

NASA Technical Reports Server (NTRS)

Anand, D. K.; Kirk, J. A.; Zmood, R. B.; Pang, D.; Lashley, C.

1991-01-01

A prototype of a 500 Wh magnetically suspended flywheel energy storage system was designed, built, and tested. The authors present the work done and include the following: (1) a final design of the magnetic bearing, control system, and motor/generator, (2) construction of a prototype system consisting of the magnetic bearing stack, flywheel, motor, container, and display module, and (3) experimental results for the magnetic bearings, motor, and the entire system. The successful completion of the prototype system has achieved: (1) manufacture of tight tolerance bearings, (2) stability and spin above the first critical frequency, (3) use of inside sensors to eliminate runout problems, and (4) integration of the motor and magnetic bearings.

A synthetic mammalian electro-genetic transcription circuit

PubMed Central

Weber, Wilfried; Luzi, Stefan; Karlsson, Maria; Sanchez-Bustamante, Carlota Diaz; Frey, Urs; Hierlemann, Andreas; Fussenegger, Martin

2009-01-01

Electric signal processing has evolved to manage rapid information transfer in neuronal networks and muscular contraction in multicellular organisms and controls the most sophisticated man-built devices. Using a synthetic biology approach to assemble electronic parts with genetic control units engineered into mammalian cells, we designed an electric power-adjustable transcription control circuit able to integrate the intensity of a direct current over time, to translate the amplitude or frequency of an alternating current into an adjustable genetic readout or to modulate the beating frequency of primary heart cells. Successful miniaturization of the electro-genetic devices may pave the way for the design of novel hybrid electro-genetic implants assembled from electronic and genetic parts. PMID:19190091

Final prototype of magnetically suspended flywheel energy storage system

NASA Astrophysics Data System (ADS)

Anand, D. K.; Kirk, J. A.; Zmood, R. B.; Pang, D.; Lashley, C.

A prototype of a 500 Wh magnetically suspended flywheel energy storage system was designed, built, and tested. The authors present the work done and include the following: (1) a final design of the magnetic bearing, control system, and motor/generator, (2) construction of a prototype system consisting of the magnetic bearing stack, flywheel, motor, container, and display module, and (3) experimental results for the magnetic bearings, motor, and the entire system. The successful completion of the prototype system has achieved: (1) manufacture of tight tolerance bearings, (2) stability and spin above the first critical frequency, (3) use of inside sensors to eliminate runout problems, and (4) integration of the motor and magnetic bearings.

Developing Built Environment Programs in Local Health Departments: Lessons Learned From a Nationwide Mentoring Program

PubMed Central

Rube, Kate; Veatch, Maggie; Huang, Katy; Lent, Megan; Goldstein, Gail P.; Lee, Karen K.

2014-01-01

Local health departments (LHDs) have a key role to play in developing built environment policies and programs to encourage physical activity and combat obesity and related chronic diseases. However, information to guide LHDs’ effective engagement in this arena is lacking. During 2011–2012, the New York City Department of Health and Mental Hygiene (DOHMH) facilitated a built environment peer mentoring program for 14 LHDs nationwide. Program objectives included supporting LHDs in their efforts to achieve built environment goals, offering examples from DOHMH’s built environment work to guide LHDs, and building a healthy built environment learning network. We share lessons learned that can guide LHDs in developing successful healthy built environment agendas. PMID:24625166

Test and On-Orbit Experiences of FalconSAT-3

NASA Astrophysics Data System (ADS)

Saylor, W. W.; France, M. E. B.

2008-08-01

The fundamental objectives of the capstone design project in the Department of Astronautics at the United States Air Force Academy (USAFA) are for cadets to learn important engineering lessons by executing a real space mission on a Department of Defense-funded satellite project. FalconSAT-3 is a 50 kg, gravity gradient-stabilized designed and built by cadets and launched March 2007 on the first ESPA (Enhanced extended launch vehicle Satellite Payload Adapter) mission. FalconSAT-3 was one of six satellites integrated onto the launch vehicle and the nature of the mission made it that the satellite was subject to the full formality of testing requirements. Two successive gravity gradient booms failed either design requirements or environmental testing; design requirements grew dramatically during the design phase; ambiguous thermal vacuum test results led to uncertainty at launch; and after launch it was not possible to contact the satellite for several weeks.

The world's nuclear future - built on material success

NASA Astrophysics Data System (ADS)

Ion, Sue

2010-07-01

In our energy hungry world of the twenty-first century, the future of electricity generation must meet the twin challenges of security of supply and reduced carbon emissions. The expectations for nuclear power programmes to play a part in delivering success on both counts, grows ever higher. The nuclear industry is poised on a renaissance likely to dwarf the heady days of the 1960s and early 1970s. Global supply chain and project management challenges abound, now just as then. The science and engineering of materials will be key to the successful deployment and operation of a new generation of reactor systems and their associated fuel cycles. Understanding and predicting materials performance will be key to achieving life extension of existing assets and underpinning waste disposal options, as well as giving confidence to the designers, their financial backers and governments across the globe, that the next generation of reactors will deliver their full potential.

Testing of the 3M Company Composite Conductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, John P; Rizy, D Tom; Kisner, Roger A

2010-10-01

The 3M Company has developed a high-temperature low-sag conductor referred to as Aluminum-Conductor Composite-Reinforced or ACCR. The conductor uses an aluminum metal matrix material to replace the steel in conventional conductors. The objective of this work is to accelerate the commercial acceptance by electric utilities of this new conductor design by testing four representative conductor classes in controlled conditions. A unique facility called the Powerline Conductor Accelerated Testing (PCAT) Facility was built at ORNL for testing overhead conductors. The PCAT has been uniquely designed for testing overhead bare transmission line conductors at high currents and temperatures after they have beenmore » installed and tensioned to the manufacturer's specifications. The ability to operate a transmission line conductor in this manner does not exist elsewhere in the United States. Four classes of ACCR cable designed by the 3M Company have been successfully test at ORNL small, medium, large and small/compact. Based on these and other manufacturer tests, the 3M Company has successfully introduced the ACCR into the commercial market and has completed over twenty installations for utility companies.« less

Nanosail-D: The Small Satellite That Could!

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.; Casas, Joseph P.; Agasid, Elwood F.; Adams, Charles L.; Laue, Greg; Kitts, Christopher; O'Brien, Sue

2011-01-01

Three years from its initial design review, NanoSail-D successfully deployed its sail on January 20th, 2011. It became the first solar sail vehicle to orbit the earth and the second sail ever unfurled in space. The NanoSail-D mission had two main objectives: eject a nanosatellite from a microsatellite; deploy its sail from a highly compacted volume and low mass system to validate large structure deployment and potential de-orbit technologies. These objectives were successfully achieved and the de-orbit analysis is in process. This paper presents an overview of the NanoSail-D project and insights into how potential setbacks were overcome. Many lessons have been learned during these past three years and are discussed in light of the phenomenal success and interest that this small satellite has generated. NanoSail-D was jointly designed and built by NASA's Marshall Space Flight Center and NASA's Ames Research Center. ManTech/NeXolve Corporation also provided key sail design support. The NanoSail-D experiment is managed by Marshall and jointly sponsored by the Army Space and Missile Defense Command, the Von Braun Center for Science and Innovation and Dynetics Inc. Ground operations support was provided by Santa Clara University, with radio beacon packets received from amateur operators around the world.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorr, Kent A.; Ostrom, Michael J.; Freeman-Pollard, Jhivaun R.

CH2M Hill Plateau Remediation Company (CHPRC) designed, constructed, commissioned, and began operation of the largest groundwater pump and treatment facility in the U.S. Department of Energy’s (DOE) nationwide complex. This one-of-a-kind groundwater pump and treatment facility, located at the Hanford Nuclear Reservation Site (Hanford Site) in Washington State, was built to an accelerated schedule with American Recovery and Reinvestment Act (ARRA) funds. There were many contractual, technical, configuration management, quality, safety, and Leadership in Energy and Environmental Design (LEED) challenges associated with the design, procurement, construction, and commissioning of this $95 million, 52,000 ft groundwater pump and treatment facility tomore » meet DOE’s mission objective of treating contaminated groundwater at the Hanford Site with a new facility by June 28, 2012. The project team’s successful integration of the project’s core values and green energy technology throughout design, procurement, construction, and start-up of this complex, first-of-its-kind Bio Process facility resulted in successful achievement of DOE’s mission objective, as well as attainment of LEED GOLD certification, which makes this Bio Process facility the first non-administrative building in the DOE Office of Environmental Management complex to earn such an award.« less

Expanded explorations into the optimization of an energy function for protein design

PubMed Central

Huang, Yao-ming; Bystroff, Christopher

2014-01-01

Nature possesses a secret formula for the energy as a function of the structure of a protein. In protein design, approximations are made to both the structural representation of the molecule and to the form of the energy equation, such that the existence of a general energy function for proteins is by no means guaranteed. Here we present new insights towards the application of machine learning to the problem of finding a general energy function for protein design. Machine learning requires the definition of an objective function, which carries with it the implied definition of success in protein design. We explored four functions, consisting of two functional forms, each with two criteria for success. Optimization was carried out by a Monte Carlo search through the space of all variable parameters. Cross-validation of the optimized energy function against a test set gave significantly different results depending on the choice of objective function, pointing to relative correctness of the built-in assumptions. Novel energy cross-terms correct for the observed non-additivity of energy terms and an imbalance in the distribution of predicted amino acids. This paper expands on the work presented at ACM-BCB, Orlando FL , October 2012. PMID:24384706

ISS External Contamination Environment for Space Science Utilization

NASA Technical Reports Server (NTRS)

Soares, Carlos; Mikatarian, Ron; Steagall, Courtney; Huang, Alvin; Koontz, Steven; Worthy, Erica

2014-01-01

(1) The International Space Station is the largest and most complex on-orbit platform for space science utilization in low Earth orbit, (2) Multiple sites for external payloads, with exposure to the associated natural and induced environments, are available to support a variety of space science utilization objectives, (3) Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle, and (4)The ISS has been designed, built and integrated with strict contamination requirements to provide low levels of induced contamination on external payload assets.

Experimental Study of a Hot Structure for a Reentry Vehicle

NASA Technical Reports Server (NTRS)

Pride, Richard A.; Royster, Dick M.; Helms, Bobbie F.

1960-01-01

A large structural model of a reentry vehicle has been built incorporating design concepts applicable to a radiation-cooled vehicle. Thermal-stress alleviating features of the model are discussed. Environmental tests on the model include approximately 100 cycles of loading at room temperature and 33 cycles of combined loading and-heating up to temperatures of 1,6000 F. Measured temperatures are shown for typical parts of the model. Comparisons are made between experimental and calculated deflections and strains. The structure successfully survived the heating and loading environments.

Construction and calibration of a low cost and fully automated vibrating sample magnetometer

NASA Astrophysics Data System (ADS)

El-Alaily, T. M.; El-Nimr, M. K.; Saafan, S. A.; Kamel, M. M.; Meaz, T. M.; Assar, S. T.

2015-07-01

A low cost vibrating sample magnetometer (VSM) has been constructed by using an electromagnet and an audio loud speaker; where both are controlled by a data acquisition device. The constructed VSM records the magnetic hysteresis loop up to 8.3 KG at room temperature. The apparatus has been calibrated and tested by using magnetic hysteresis data of some ferrite samples measured by two scientifically calibrated magnetometers; model (Lake Shore 7410) and model (LDJ Electronics Inc. Troy, MI). Our VSM lab-built new design proved success and reliability.

External Contamination Environment at ISS Included: Selected Results from Payloads Contamination Mapping Delivery 3 Package

NASA Technical Reports Server (NTRS)

Olsen, Randy; Huang, Alvin; Steagall, Courtney; Kohl, Nathaniel; Koontz, Steve; Worthy, Erica

2017-01-01

The International Space Station is the largest and most complex on-orbit platform for space science utilization in low Earth orbit. Multiple sites for external payloads, with exposure to the associated natural and induced environments, are available to support a variety of space science utilization objectives. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. The ISS has been designed, built and integrated with strict contamination requirements to provide low levels of induced contamination on external payload assets.

Built spaces and features associated with user satisfaction in maternity waiting homes in Malawi.

PubMed

McIntosh, Nathalie; Gruits, Patricia; Oppel, Eva; Shao, Amie

2018-07-01

To assess satisfaction with maternity waiting home built spaces and features in women who are at risk for underutilizing maternity waiting homes (i.e. residential facilities that temporarily house near-term pregnant mothers close to healthcare facilities that provide obstetrical care). Specifically we wanted to answer the questions: (1) Are built spaces and features associated with maternity waiting home user satisfaction? (2) Can built spaces and features designed to improve hygiene, comfort, privacy and function improve maternity waiting home user satisfaction? And (3) Which built spaces and features are most important for maternity waiting home user satisfaction? A cross-sectional study comparing satisfaction with standard and non-standard maternity waiting home designs. Between December 2016 and February 2017 we surveyed expectant mothers at two maternity waiting homes that differed in their design of built spaces and features. We used bivariate analyses to assess if built spaces and features were associated with satisfaction. We compared ratings of built spaces and features between the two maternity waiting homes using chi-squares and t-tests to assess if design features to improve hygiene, comfort, privacy and function were associated with higher satisfaction. We used exploratory robust regression analysis to examine the relationship between built spaces and features and maternity waiting home satisfaction. Two maternity waiting homes in Malawi, one that incorporated non-standardized design features to improve hygiene, comfort, privacy, and function (Kasungu maternity waiting home) and the other that had a standard maternity waiting home design (Dowa maternity waiting home). 322 expectant mothers at risk for underutilizing maternity waiting homes (i.e. first-time mothers and those with no pregnancy risk factors) who had stayed at the Kasungu or Dowa maternity waiting homes. There were significant differences in ratings of built spaces and features between the two differently designed maternity waiting homes, with the non-standard design having higher ratings for: adequacy of toilets, and ratings of heating/cooling, air and water quality, sanitation, toilets/showers and kitchen facilities, building maintenance, sleep area, private storage space, comfort level, outdoor spaces and overall satisfaction (p = <.0001 for all). The final regression model showed that built spaces and features that are most important for maternity waiting home user satisfaction are toilets/showers, guardian spaces, safety, building maintenance, sleep area and private storage space (R 2  = 0.28). The design of maternity waiting home built spaces and features is associated with user satisfaction in women at risk for underutilizing maternity waiting homes, especially related to toilets/showers, guardian spaces, safety, building maintenance, sleep area and private storage space. Improving maternity waiting home built spaces and features may offer a promising area for improving maternity waiting home satisfaction and reducing barriers to maternity waiting home use. Copyright © 2018 Elsevier Ltd. All rights reserved.

Habitat for Humanity: La Grange, Georgia, 2003 Jimmy Carter Work Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2005-06-01

The Troup-Chambers Habitat for Humanity built a Habitat house to ENERGY STAR standards in LaGrange, Georgia, in 2003. The project was so successfully that all Troup-Chambers houses will now be built to ENERGY STAR standards.

Advanced Stirling receiver development program, phase 1

NASA Technical Reports Server (NTRS)

Lurio, Charles A.

1990-01-01

Critical technology experiments were designed and developed to evaluate the Stirling cavity heat pipe receiver for a space solar power system. Theoretical criteria were applied to the design of a module for containing energy storage phase change material while avoiding thermal ratcheting. Zero-g drop tower tests, without phase change, were conducted to affirm that the bubble location required to avoid ratcheting could be achieved without the use of container materials that are wetted by the phase change material. A full scale module was fabricated, but not tested. A fabrication method was successfully developed for the sodium evaporator dome, with a sintered screen wick, to be used as the focal point for the receiver. Crushing of the screen during hydroforming was substantially reduced over the results of other researchers by using wax impregnation. Superheating of the sodium in the wick under average flux conditions is expected to be under 10K. A 2000K furnace which will simulate solar flux conditions for testing the evaporator dome was successfully built and tested.

Concepts, requirements, and design approaches for building successful planning and scheduling systems

NASA Technical Reports Server (NTRS)

Hornstein, Rhoda Shaller; Willoughby, John K.

1991-01-01

Traditional practice of systems engineering management assumes requirements can be precisely determined and unambiguously defined prior to system design and implementation; practice further assumes requirements are held static during implementation. Human-computer decision support systems for service planning and scheduling applications do not conform well to these assumptions. Adaptation to the traditional practice of systems engineering management are required. Basic technology exists to support these adaptations. Additional innovations must be encouraged and nutured. Continued partnership between the programmatic and technical perspective assures proper balance of the impossible with the possible. Past problems have the following origins: not recognizing the unusual and perverse nature of the requirements for planning and scheduling; not recognizing the best starting point assumptions for the design; not understanding the type of system that being built; and not understanding the design consequences of the operations concept selected.

Design of a Thermal Precipitator for the Characterization of Smoke Particles from Common Spacecraft Materials

NASA Technical Reports Server (NTRS)

Meyer, Marit Elisabeth

2015-01-01

A thermal precipitator (TP) was designed to collect smoke aerosol particles for microscopic analysis in fire characterization research. Information on particle morphology, size and agglomerate structure obtained from these tests supplements additional aerosol data collected. Modeling of the thermal precipitator throughout the design process was performed with the COMSOL Multiphysics finite element software package, including the Eulerian flow field and thermal gradients in the fluid. The COMSOL Particle Tracing Module was subsequently used to determine particle deposition. Modeling provided optimized design parameters such as geometry, flow rate and temperatures. The thermal precipitator was built and testing verified the performance of the first iteration of the device. The thermal precipitator was successfully operated and provided quality particle samples for microscopic analysis, which furthered the body of knowledge on smoke particulates. This information is a key element of smoke characterization and will be useful for future spacecraft fire detection research.

Engineering a Functional Small RNA Negative Autoregulation Network with Model-Guided Design.

PubMed

Hu, Chelsea Y; Takahashi, Melissa K; Zhang, Yan; Lucks, Julius B

2018-05-22

RNA regulators are powerful components of the synthetic biology toolbox. Here, we expand the repertoire of synthetic gene networks built from these regulators by constructing a transcriptional negative autoregulation (NAR) network out of small RNAs (sRNAs). NAR network motifs are core motifs of natural genetic networks, and are known for reducing network response time and steady state signal. Here we use cell-free transcription-translation (TX-TL) reactions and a computational model to design and prototype sRNA NAR constructs. Using parameter sensitivity analysis, we design a simple set of experiments that allow us to accurately predict NAR function in TX-TL. We transfer successful network designs into Escherichia coli and show that our sRNA transcriptional network reduces both network response time and steady-state gene expression. This work broadens our ability to construct increasingly sophisticated RNA genetic networks with predictable function.

Fully chip-embedded automation of a multi-step lab-on-a-chip process using a modularized timer circuit.

PubMed

Kang, Junsu; Lee, Donghyeon; Heo, Young Jin; Chung, Wan Kyun

2017-11-07

For highly-integrated microfluidic systems, an actuation system is necessary to control the flow; however, the bulk of actuation devices including pumps or valves has impeded the broad application of integrated microfluidic systems. Here, we suggest a microfluidic process control method based on built-in microfluidic circuits. The circuit is composed of a fluidic timer circuit and a pneumatic logic circuit. The fluidic timer circuit is a serial connection of modularized timer units, which sequentially pass high pressure to the pneumatic logic circuit. The pneumatic logic circuit is a NOR gate array designed to control the liquid-controlling process. By using the timer circuit as a built-in signal generator, multi-step processes could be done totally inside the microchip without any external controller. The timer circuit uses only two valves per unit, and the number of process steps can be extended without limitation by adding timer units. As a demonstration, an automation chip has been designed for a six-step droplet treatment, which entails 1) loading, 2) separation, 3) reagent injection, 4) incubation, 5) clearing and 6) unloading. Each process was successfully performed for a pre-defined step-time without any external control device.

The DARPA compact superconducting x-ray lithography source features. [Defense Advanced Research Projects Agency (DARPA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heese, R.; Kalsi, S.; Leung, E.

1991-01-01

Under DARPA sponsorship, a compact Superconducting X-ray Lithography Source (SXLS) is being designed and built by the Brookhaven National Laboratory (BNL) with industry participation from Grumman Corporation and General Dynamics. This source is optimized for lithography work for sub-micron high density computer chips, and is about the size of a billiard table (1.5 m {times} 4.0 m). The machine has a racetrack configuration with two 180{degree} bending magnets being designed and built by General Dynamics under a subcontract with Grumman Corporation. The machine will have 18 photon ports which would deliver light peaked at a wave length of 10 Angstroms.more » Grumman is commercializing the SXLS device and plans to book orders for delivery of industrialized SXLS (ISXLS) versions in 1995. This paper will describe the major features of this device. The commercial machine will be equipped with a fully automated user-friendly control systems, major features of which are already working on a compact warm dipole ring at BNL. This ring has normal dipole magnets with dimensions identical to the SXLS device, and has been successfully commissioned. 4 figs., 1 tab.« less

Separator development and testing of nickel-hydrogen cells

NASA Technical Reports Server (NTRS)

Gonzalez-Sanabria, O. D.; Manzo, M. A.

1984-01-01

The components, design, and operating characteristics of Ni-H2 cells batteries were improved. A separator development program was designed to develop a separator that is resistant to penetration by oxygen and loose active material from then nickel electrode, while retraining the required chemical and thermal stability, reservoir capability, and high ionic conductivity. The performance of the separators in terms of cell operating voltage was to at least match that of state-of-the-art separators while eliminating the separator problems. The separators were submitted to initial screening tests and those which successfully completed the tests were built into Ni-H2 cells for short term testing. The separators with the best performance are tested for long term performance and life.

The Scenario-Based Engineering Process (SEP): a user-centered approach for the development of health care systems.

PubMed

Harbison, K; Kelly, J; Burnell, L; Silva, J

1995-01-01

The Scenario-based Engineering Process (SEP) is a user-focused methodology for large and complex system design. This process supports new application development from requirements analysis with domain models to component selection, design and modification, implementation, integration, and archival placement. It is built upon object-oriented methodologies, domain modeling strategies, and scenario-based techniques to provide an analysis process for mapping application requirements to available components. We are using SEP in the health care applications that we are developing. The process has already achieved success in the manufacturing and military domains and is being adopted by many organizations. SEP should prove viable in any domain containing scenarios that can be decomposed into tasks.

Performance of conduction cooled splittable superconducting magnet package for linear accelerators

DOE PAGES

Kashikhin, Vladimire S.; Andreev, N.; Cheban, S.; ...

2016-02-19

New Linear Superconducting Accelerators need a superconducting magnet package installed inside SCRF Cryomodules to focus and steer electron or proton beams. A superconducting magnet package was designed and built as a collaborative effort of FNAL and KEK. The magnet package includes one quadrupole, and two dipole windings. It has a splittable in the vertical plane configuration, and features for conduction cooling. The magnet was successfully tested at room temperature, in a liquid He bath, and in a conduction cooling experiment. The paper describes the design and test results including: magnet cooling, training, and magnetic measurements by rotational coils. Furthermore, themore » effects of superconductor and iron yoke magnetization, hysteresis, and fringe fields are discussed.« less

Affordable Hybrid Heat Pump Clothes Dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

TeGrotenhuis, Ward E.; Butterfield, Andrew; Caldwell, Dustin D.

This project was successful in demonstrating the feasibility of a step change in residential clothes dryer energy efficiency by demonstrating heat pump technology capable of 50% energy savings over conventional standard-size electric dryers with comparable drying times. A prototype system was designed from off-the-shelf components that can meet the project’s efficiency goals and are affordable. An experimental prototype system was built based on the design that reached 50% energy savings. Improvements have been identified that will reduce drying times of over 60 minutes to reach the goal of 40 minutes. Nevertheless, the prototype represents a step change in efficiency overmore » heat pump dryers recently introduced to the U.S. market, with 30% improvement in energy efficiency at comparable drying times.« less

A new surface-potential-based compact model for the MoS2 field effect transistors in active matrix display applications

NASA Astrophysics Data System (ADS)

Cao, Jingchen; Peng, Songang; Liu, Wei; Wu, Quantan; Li, Ling; Geng, Di; Yang, Guanhua; Ji, Zhouyu; Lu, Nianduan; Liu, Ming

2018-02-01

We present a continuous surface-potential-based compact model for molybdenum disulfide (MoS2) field effect transistors based on the multiple trapping release theory and the variable-range hopping theory. We also built contact resistance and velocity saturation models based on the analytical surface potential. This model is verified with experimental data and is able to accurately predict the temperature dependent behavior of the MoS2 field effect transistor. Our compact model is coded in Verilog-A, which can be implemented in a computer-aided design environment. Finally, we carried out an active matrix display simulation, which suggested that the proposed model can be successfully applied to circuit design.

Space Station Freedom coupling tasks: An evaluation of their space operational compatibility

NASA Technical Reports Server (NTRS)

Sampaio, Carlos E.; Bierschwale, John M.; Fleming, Terence F.; Stuart, Mark A.

1991-01-01

The development of the Space Station Freedom tasks that are compatible with both telerobotic as well as extravehicular activity is a necessary redundancy in order to insure successful day to day operation. One task to be routinely performed aboard Freedom will be the changeout of various quick disconnect fluid connectors. In an attempt to resolve these potentially contradictory issues of compatibility, mock-ups of couplings suitable to both extravehicular as well as telerobotic activity were designed and built. An evaluation performed at the Remote Operator Interaction Laboratory at NASA's Johnson Space Center is discussed, which assessed the prototype couplings as well as three standard coupling designs. Data collected during manual and telerobotic manipulation of the couplings indicated that the custom coupling was in fact shown to be faster to operate and generally preferred over the standard coupling designs.

Design and Early In-flight Performance of the Tropical Rainfall Measuring Mission (TRMM) Power Subsystem

NASA Technical Reports Server (NTRS)

Moran, Vickie Eakin; Flatley, Thomas P.; Shue, John; Gaddy, Edward M.; Manzer, Dominic; Hicks, Edward

1998-01-01

Maryland built the spacecraft in-house with four U.S. instruments and one Japanese instrument, the first space flown Precipitation Radar (PR). The TRMM Observatory was successfully launched from Tanegashima Space Center in Japan on an H-2 Expendable Launch Vehicle on November 27, 1997. This paper presents an overview of the TRMM Power System including its design, testing, and in flight performance for the first 70 days. Finally, key lessons learned are presented. The TRMM power system consists of an 18.1 square meter deployed solar array fabricated by TRW with Tecstar GaAs/Ge cells, two (2) Hughes 50 Ampere-Hour (Ah) Super NiCd' batteries, each with 22 Eagle-Picher cells, and three (3) electronics boxes designed to provide power regulation, battery charge control, and command and telemetry interface.

Leadership success within disaster restoration projects.

PubMed

Rapp, Randy R; Baroudi, Bassam

2014-01-01

Successful project managers draw their performance from essential leadership traits, as guided by their core values.Within disaster recovery, contractors who mitigate, repair, and reconstruct the built environment are often faced with challenges exceeding the norm. The effective leader is commonly expected to consider stakeholder motivations within distressing situations as well as other external and environmental factors when seeking to lead the project team to successful outcomes. This research is most concerned with leadership within the context of disaster restoration of the built environment. Its stimulus comes from the Restoration Industry Association (RIA)'s efforts to highlight leadership traits and core values for its Certified Restorer Body of Knowledge but would be of value to others associated with disaster recovery operations. Among organizations whose membership includes thousands of practitioners who restore and reconstruct the built environment after disasters, the RIA is the only one yet to formally and substantially research which core values and leader traits are deemed critical for the success of efforts to manage the means and methods applied on recovery job sites. Forty-six seasoned disaster restoration industry project professionals voluntarily responded to a survey questionnaire that sought their opinions about the traits and core values that they consider most important for successful disaster restoration project leadership. The most important leader traits were effective communication, professional competence, and leadership by example. The most important restoration industry values were integrity, compassion, and trustworthiness. The recognized imperative of compassion was unexpected in light of stereotypes often associated with construction-related contractors. This and other findings permit disaster response and recovery stakeholders to better understand qualities they should wish to see in leaders of contractor organizations, which they hire to restore and reconstruct the built environment after catastrophic events.

Integration and use of Microgravity Research Facility: Lessons learned by the crystals by vapor transport experiment and Space Experiments Facility programs

NASA Technical Reports Server (NTRS)

Heizer, Barbara L.

1992-01-01

The Crystals by Vapor Transport Experiment (CVTE) and Space Experiments Facility (SEF) are materials processing facilities designed and built for use on the Space Shuttle mid deck. The CVTE was built as a commercial facility owned by the Boeing Company. The SEF was built under contract to the UAH Center for Commercial Development of Space (CCDS). Both facilities include up to three furnaces capable of reaching 850 C minimum, stand-alone electronics and software, and independent cooling control. In addition, the CVTE includes a dedicated stowage locker for cameras, a laptop computer, and other ancillary equipment. Both systems are designed to fly in a Middeck Accommodations Rack (MAR), though the SEF is currently being integrated into a Spacehab rack. The CVTE hardware includes two transparent furnaces capable of achieving temperatures in the 850 to 870 C range. The transparent feature allows scientists/astronauts to directly observe and affect crystal growth both on the ground and in space. Cameras mounted to the rack provide photodocumentation of the crystal growth. The basic design of the furnace allows for modification to accommodate techniques other than vapor crystal growth. Early in the CVTE program, the decision was made to assign a principal scientist to develop the experiment plan, affect the hardware/software design, run the ground and flight research effort, and interface with the scientific community. The principal scientist is responsible to the program manager and is a critical member of the engineering development team. As a result of this decision, the hardware/experiment requirements were established in such a way as to balance the engineering and science demands on the equipment. Program schedules for hardware development, experiment definition and material selection, flight operations development and crew training, both ground support and astronauts, were all planned and carried out with the understanding that the success of the program science was as important as the hardware functionality. How the CVTE payload was designed and what it is capable of, the philosophy of including the scientists in design and operations decisions, and the lessons learned during the integration process are descussed.

Probabilistic Risk Assessment (PRA): A Practical and Cost Effective Approach

NASA Technical Reports Server (NTRS)

Lee, Lydia L.; Ingegneri, Antonino J.; Djam, Melody

2006-01-01

The Lunar Reconnaissance Orbiter (LRO) is the first mission of the Robotic Lunar Exploration Program (RLEP), a space exploration venture to the Moon, Mars and beyond. The LRO mission includes spacecraft developed by NASA Goddard Space Flight Center (GSFC) and seven instruments built by GSFC, Russia, and contractors across the nation. LRO is defined as a measurement mission, not a science mission. It emphasizes the overall objectives of obtaining data to facilitate returning mankind safely to the Moon in preparation for an eventual manned mission to Mars. As the first mission in response to the President's commitment of the journey of exploring the solar system and beyond: returning to the Moon in the next decade, then venturing further into the solar system, ultimately sending humans to Mars and beyond, LRO has high-visibility to the public but limited resources and a tight schedule. This paper demonstrates how NASA's Lunar Reconnaissance Orbiter Mission project office incorporated reliability analyses in assessing risks and performing design tradeoffs to ensure mission success. Risk assessment is performed using NASA Procedural Requirements (NPR) 8705.5 - Probabilistic Risk Assessment (PRA) Procedures for NASA Programs and Projects to formulate probabilistic risk assessment (PRA). As required, a limited scope PRA is being performed for the LRO project. The PRA is used to optimize the mission design within mandated budget, manpower, and schedule constraints. The technique that LRO project office uses to perform PRA relies on the application of a component failure database to quantify the potential mission success risks. To ensure mission success in an efficient manner, low cost and tight schedule, the traditional reliability analyses, such as reliability predictions, Failure Modes and Effects Analysis (FMEA), and Fault Tree Analysis (FTA), are used to perform PRA for the large system of LRO with more than 14,000 piece parts and over 120 purchased or contractor built components.

Isaac Newton and Student College Completion

ERIC Educational Resources Information Center

Tinto, Vincent

2013-01-01

Success in college is built upon classroom success, but success in the classroom does not in itself ensure college completion. Completion arises from success in a sequence of classes one after another over time. It does so most frequently when students are presented with coherent course pathways to degree completion, are able to gain degree credit…

Get Active Orlando: changing the built environment to increase physical activity.

PubMed

McCreedy, Malisa; Leslie, Jill G

2009-12-01

Active Living by Design's Get Active Orlando partnership (GAO) focused on downtown Orlando's Community Redevelopment Area, including the Parramore Heritage District, home to many low-income and ethnically diverse residents, including many seniors. The area had undergone substantial development, and GAO aimed to incorporate active living considerations into the city's changing landscape. Get Active Orlando conducted a baseline survey of all streets, sidewalks, and bicycle lanes in the project area and identified a sequence of plans and policies in which to incorporate changes identified in the assessment. To create more immediate opportunities for active living, the partnership initiated a senior walking program, a bicycle refurbishment and giveaway program, and community bicycle-riding events, and led a social-marketing campaign that emphasized simple lifestyle changes. Get Active Orlando influenced adoption of public policies supporting active living in Orlando, including the Downtown Transportation Plan, Streetscape Guidelines, Design Standards Review Checklist, and growth management policies. Establishment of the Mayor's Advisory Council on Active Living is testament to the heightened significance of active living in Orlando. Initial assessment data served as a strong platform for policy change. Creating connections across disciplines including land-use planning, transportation, public health, and economic development allowed GAO to secure substantial policy change to influence design of the built environment. Engaging community members, including youth, as leaders was an important factor in program success. The physical environment in Orlando's Community Redevelopment Area is beginning to change as a reflection of a new policy framework designed to support active living.

Esthetics built to last: treatment of functional anomalies may need to precede esthetic corrections.

PubMed

Bassett, Joyce L

2014-02-01

In this case of a 33 year-old male patient seeking a more esthetically pleasing smile, comprehensive restorative treatment planning included recognition of the patient's incisor position and morphology, dentofacial requirements, and appropriate vertical dimension. The accepted treatment plan consisted of orthodontic correction of the patient's anterior constriction, followed by placement of eight maxillary veneers and composite augmentation on the mandibular incisors and canines. Keys to achieving a successful outcome included knowledge of smile design, material selection, and preparation techniques. The case demonstrates how functional problems oftentimes must be addressed before esthetic correction can be made.

Magnetic Leviation System Design and Implementation for Wind Tunnel Application

NASA Technical Reports Server (NTRS)

Lin, Chin E.; Sheu, Yih-Ran; Jou, Hui-Long

1996-01-01

This paper presents recent work in magnetic suspension wind tunnel development in National Cheng Kung University. In this phase of research, a control-based study is emphasized to implement a robust control system into the experimental system under study. A ten-coil 10 cm x 10 cm magnetic suspension wind tunnel is built using a set of quadrant detectors for six degree of freedom control. To achieve the attitude control of suspended model with different attitudes, a spacial electromagnetic field simulation using OPERA 3D is studied. A successful test for six degree of freedom control is demonstrated in this paper.

SMAP Verification and Validation Project - Final Report

NASA Technical Reports Server (NTRS)

Murry, Michael

2012-01-01

In 2007, the National Research Council (NRC) released the Decadal Survey of Earth science. In the future decade, the survey identified 15 new space missions of significant scientific and application value for the National Aeronautics and Space Administration (NASA) to undertake. One of these missions was the Soil Moisture Active Passive (SMAP) mission that NASA assigned to the Jet Propulsion Laboratory (JPL) in 2008. The goal of SMAP1 is to provide global, high resolution mapping of soil moisture and its freeze/thaw states. The SMAP project recently passed its Critical Design Review and is proceeding with its fabrication and testing phase.Verification and Validation (V&V) is widely recognized as a critical component in system engineering and is vital to the success of any space mission. V&V is a process that is used to check that a system meets its design requirements and specifications in order to fulfill its intended purpose. Verification often refers to the question "Have we built the system right?" whereas Validation asks "Have we built the right system?" Currently the SMAP V&V team is verifying design requirements through inspection, demonstration, analysis, or testing. An example of the SMAP V&V process is the verification of the antenna pointing accuracy with mathematical models since it is not possible to provide the appropriate micro-gravity environment for testing the antenna on Earth before launch.

Small Satellites for Secondary Students

NASA Astrophysics Data System (ADS)

Zack, Kevin; Cominsky, Lynn

2012-11-01

Small Satellites for Secondary Students is a program funded by a three-year grant from NASA to bridge the gap in STEM education for secondary-school students. This is accomplished by creating the educational resources that are needed to support the development of a small scientific payload in alignment with scientific and technological education standards. The prototype payloads are flexible multi-experiment platforms designed to accommodate a wide range of student abilities with minimal resource requirements. The heart of each payload is an Arduino microcontroller which communicates with components that provide sensor data, Global Positioning System information, and which offer on-board data storage. The payload is built with off-the-shelf components and a pre-etched, custom-designed connector board. The platform also supports real-time telemetry updates through the use of Wi-Fi. To date, the prototype payloads have been tested on both high-powered rockets reaching over 3km and weather balloons tethered at 300m. Multiple successful rocket test runs reaching 1km have been conducted in partnership with amateur rocket clubs including the Association of Experimental Rocketry of the Pacific. From these flights, we are continuing to improve the payload design in order to increase the likelihood of student success.

The built environment moderates effects of family-based childhood obesity treatment over 2 years.

PubMed

Epstein, Leonard H; Raja, Samina; Daniel, Tinuke Oluyomi; Paluch, Rocco A; Wilfley, Denise E; Saelens, Brian E; Roemmich, James N

2012-10-01

Research suggests the neighborhood built environment is related to child physical activity and eating. The purpose of this study was to determine if characteristics of the neighborhood environment moderate the relationship between obesity treatment and weight loss, and if outcomes of particular treatments are moderated by built environment characteristics. The relationship between the built environment and standardized BMI (zBMI) changes for 191 8-12-year-old children who participated in one of four randomized, controlled trials of pediatric weight management was assessed using mixed models analysis of covariance. At 2-year follow-up, greater parkland, fewer convenience stores, and fewer supermarkets were associated with greater zBMI reduction across all interventions. No treatments interacted with characteristics of the built environment. Activity- and eating-related built neighborhood characteristics are associated with child success in behavioral obesity treatments. Efficacy may be improved by individualizing treatments based on built environment characteristics.

The Human Powered Submarine Team of Virginia Tech Propulsion System Design Final Report

NASA Technical Reports Server (NTRS)

An, Eric; Bennett, Matt; Callis, Ron; Chen, Chester; Lee, John; Milan-Williams, Kristy

1999-01-01

The Human Powered Submarine Team has been in existence at Virginia Tech since its conception in 1993. Since then, it has served as a way for engineering students from many different disciplines to implement design conception and realization. The first submarine built was Phantom 1, a two-man submarine made of fiberglass. After construction was complete, Phantom 1 was ready for racing, but, unfortunately, suffered fatal problems come race time. The submarine team slowed down a bit after experiencing racing problems, but was revived in 1995 when design efforts for a new two-man submarine, the Phantom 2 commence. The propulsion system consisted of a chain and gear drive system using an ultra-light helicopter tail rotor for a propeller. Although the team learned valuable lessons as a result of Phantom 1's problems, Phantom 2 still experiences problems at races. After various parts of Phantom 2 are redesigned, it is once again ready for racing and proves that the redesign was well worth the time and effort. In 1997, Phantom 2 not only finishes its first race, held in San Diego, California, but comes in third. This success sparks yet another revival of the submarine team and design for the team's current project, the Phantom 3, a one-man submarine, is started. In 1998, the plug for Phantom 3 is built and the hull is constructed. With so many past problems from which to learn, Phantom 3 promises to be the fastest and best-designed submarine the team has developed thus far. The current speed world-record is 7 knots.

Advanced life support control/monitor instrumentation concepts for flight application

NASA Technical Reports Server (NTRS)

Heppner, D. B.; Dahlhausen, M. J.; Fell, R. B.

1986-01-01

Development of regenerative Environmental Control/Life Support Systems requires instrumentation characteristics which evolve with successive development phases. As the development phase moves toward flight hardware, the system availability becomes an important design aspect which requires high reliability and maintainability. This program was directed toward instrumentation designs which incorporate features compatible with anticipated flight requirements. The first task consisted of the design, fabrication and test of a Performance Diagnostic Unit. In interfacing with a subsystem's instrumentation, the Performance Diagnostic Unit is capable of determining faulty operation and components within a subsystem, perform on-line diagnostics of what maintenance is needed and accept historical status on subsystem performance as such information is retained in the memory of a subsystem's computerized controller. The second focus was development and demonstration of analog signal conditioning concepts which reduce the weight, power, volume, cost and maintenance and improve the reliability of this key assembly of advanced life support instrumentation. The approach was to develop a generic set of signal conditioning elements or cards which can be configured to fit various subsystems. Four generic sensor signal conditioning cards were identified as being required to handle more than 90 percent of the sensors encountered in life support systems. Under company funding, these were detail designed, built and successfully tested.

Designing and Testing a Blended Wing Body with Boundary Layer Ingestion Nacelles

NASA Technical Reports Server (NTRS)

Carter, Melissa B.; Campbell, Richard L.; Pendergraft, Odis C.; Underwood, Pamela J.; Friedman, Douglas M.; Serrano, Leonel

2006-01-01

A knowledge-based aerodynamic design method coupled with an unstructured grid Navier-Stokes flow solver was used to improve the propulsion/airframe integration for a Blended Wing Body with boundary-layer ingestion nacelles. A new zonal design capability was used that significantly reduced the time required to achieve a successful design for each nacelle and the elevon between them. A wind tunnel model was built with interchangeable parts reflecting the baseline and redesigned configurations and tested in the National Transonic Facility (NTF). Most of the testing was done at the cruise design conditions (Mach number = 0.85, Reynolds number = 75 million). In general, the predicted improvements in forces and moments as well as the changes in wing pressures between the baseline and redesign were confirmed by the wind tunnel results. The effectiveness of elevons between the nacelles was also predicted surprisingly well considering the crudeness in the modeling of the control surfaces in the flow code.

Launch Control Network Engineer

NASA Technical Reports Server (NTRS)

Medeiros, Samantha

2017-01-01

The Spaceport Command and Control System (SCCS) is being built at the Kennedy Space Center in order to successfully launch NASA’s revolutionary vehicle that allows humans to explore further into space than ever before. During my internship, I worked with the Network, Firewall, and Hardware teams that are all contributing to the huge SCCS network project effort. I learned the SCCS network design and the several concepts that are running in the background. I also updated and designed documentation for physical networks that are part of SCCS. This includes being able to assist and build physical installations as well as configurations. I worked with the network design for vehicle telemetry interfaces to the Launch Control System (LCS); this allows the interface to interact with other systems at other NASA locations. This network design includes the Space Launch System (SLS), Interim Cryogenic Propulsion Stage (ICPS), and the Orion Multipurpose Crew Vehicle (MPCV). I worked on the network design and implementation in the Customer Avionics Interface Development and Analysis (CAIDA) lab.

Design principles for nickel hydrogen cells and batteries

NASA Technical Reports Server (NTRS)

Thaller, L. H.

1985-01-01

Nickel hydrogen cells, and more recently, bipolar batteries have been built by a variety of organizations. The design principles that have been used by the technology group at the Lewis Research Center draw upon their extensive background in separator technology, alkaline fuel cell technology, and several alkaline cell technology areas. These design principles have been incorporated into both the more contemporary individual pressure vessel (IPV) designs that were pioneered by other groups, as well as the more recent bipolar battery designs using active cooling that are being developed at LeRC and their contractors. These principles are rather straightforward applications of capillary force formalisms, coupled with the slowly developing data base resulting from careful post test analyses. The objective of this overall effort is directed towards the low Earth orbit (LEO) application where the cycle life requirements are much more severe than the geosynchronous orbit (GEO) application. Nickel hydrogen cells have already been successfully flown in an increasing number of GEO missions.

Design and Verification of a Distributed Communication Protocol

NASA Technical Reports Server (NTRS)

Munoz, Cesar A.; Goodloe, Alwyn E.

2009-01-01

The safety of remotely operated vehicles depends on the correctness of the distributed protocol that facilitates the communication between the vehicle and the operator. A failure in this communication can result in catastrophic loss of the vehicle. To complicate matters, the communication system may be required to satisfy several, possibly conflicting, requirements. The design of protocols is typically an informal process based on successive iterations of a prototype implementation. Yet distributed protocols are notoriously difficult to get correct using such informal techniques. We present a formal specification of the design of a distributed protocol intended for use in a remotely operated vehicle, which is built from the composition of several simpler protocols. We demonstrate proof strategies that allow us to prove properties of each component protocol individually while ensuring that the property is preserved in the composition forming the entire system. Given that designs are likely to evolve as additional requirements emerge, we show how we have automated most of the repetitive proof steps to enable verification of rapidly changing designs.

IS Success Model in E-Learning Context Based on Students' Perceptions

ERIC Educational Resources Information Center

Freeze, Ronald D.; Alshare, Khaled A.; Lane, Peggy L.; Wen, H. Joseph

2010-01-01

This study utilized the Information Systems Success (ISS) model in examining e-learning systems success. The study was built on the premise that system quality (SQ) and information quality (IQ) influence system use and user satisfaction, which in turn impact system success. A structural equation model (SEM), using LISREL, was used to test the…

Supplantation versus Generative Models: Implications for Designers of Instructional Text.

ERIC Educational Resources Information Center

Smith, Patricia L.

Two instructional design alternatives are described and discussed: (1) the supplantation model of Ausburn and Ausburn (1978), where learning strategies are built into the instructional materials; and (2) a generative design model, where strategies are "built" into the learner. These contrasting models are proposed as representing the…

Design in the Classroom: Exploring the Built Environment.

ERIC Educational Resources Information Center

Maine Arts Commission, Augusta.

Design and the built environment are subjects of concern to Maine communities. State mandated town planning, new school construction, and the Department of Transportation plans to rebuild roads and bridges elicit public discussion. The study of design encourages elementary students to enter this public forum as informed citizens. The study of…

Early-Stage Software Design for Usability

ERIC Educational Resources Information Center

Golden, Elspeth

2010-01-01

In spite of the goodwill and best efforts of software engineers and usability professionals, systems continue to be built and released with glaring usability flaws that are costly and difficult to fix after the system has been built. Although user interface (UI) designers, be they usability or design experts, communicate usability requirements to…

Integrating International Engineering Organizations For Successful ISS Operations

NASA Technical Reports Server (NTRS)

Blome, Elizabeth; Duggan, Matt; Patten, L.; Pieterek, Hhtrud

2006-01-01

The International Space Station (ISS) is a multinational orbiting space laboratory that is built in cooperation with 16 nations. The design and sustaining engineering expertise is spread worldwide. As the number of Partners with orbiting elements on the ISS grows, the challenge NASA is facing as the ISS integrator is to ensure that engineering expertise and data are accessible in a timely fashion to ensure ongoing operations and mission success. Integrating international engineering teams requires definition and agreement on common processes and responsibilities, joint training and the emergence of a unique engineering team culture. ISS engineers face daunting logistical and political challenges regarding data sharing requirements. To assure systematic information sharing and anomaly resolution of integrated anomalies, the ISS Partners are developing multi-lateral engineering interface procedures. Data sharing and individual responsibility are key aspects of this plan. This paper describes several examples of successful multilateral anomaly resolution. These successes were used to form the framework of the Partner to Partner engineering interface procedures, and this paper describes those currently documented multilateral engineering processes. Furthermore, it addresses the challenges experienced to date, and the forward work expected in establishing a successful working relationship with Partners as their hardware is launched.

Energy-Performance-Based Design-Build Process: Strategies for Procuring High-Performance Buildings on Typical Construction Budgets: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheib, J.; Pless, S.; Torcellini, P.

NREL experienced a significant increase in employees and facilities on our 327-acre main campus in Golden, Colorado over the past five years. To support this growth, researchers developed and demonstrated a new building acquisition method that successfully integrates energy efficiency requirements into the design-build requests for proposals and contracts. We piloted this energy performance based design-build process with our first new construction project in 2008. We have since replicated and evolved the process for large office buildings, a smart grid research laboratory, a supercomputer, a parking structure, and a cafeteria. Each project incorporated aggressive efficiency strategies using contractual energy usemore » requirements in the design-build contracts, all on typical construction budgets. We have found that when energy efficiency is a core project requirement as defined at the beginning of a project, innovative design-build teams can integrate the most cost effective and high performance efficiency strategies on typical construction budgets. When the design-build contract includes measurable energy requirements and is set up to incentivize design-build teams to focus on achieving high performance in actual operations, owners can now expect their facilities to perform. As NREL completed the new construction in 2013, we have documented our best practices in training materials and a how-to guide so that other owners and owner's representatives can replicate our successes and learn from our experiences in attaining market viable, world-class energy performance in the built environment.« less

RED or READ: the built environment is colored

NASA Astrophysics Data System (ADS)

Smith, Dianne

2002-06-01

How important is color in the design of our built environment? Prototypes and massing models for designs are often presented in white or monochromatic combinations, irrespective of the materials incorporated and the colors that may be applied in the final constructed building, interior or object. Therefore, it is of interest to identify the way color is positioned by designers in how they go about the business of making environments. The built environment is understood by the designers and design researchers generally in one of four fields - as object, as product, as communicator, or as social domain. In addition, Franz identified four conceptions of designing held by designers - the experiential conception, the structural conception, the production conception and the retail conception. Fashion and style are often associated with color in a local context and may simply be applied to the physical environment because it is in fashion, rather than because of what it communicates more broadly. It is assumed that the integration of color in the built environment is influenced by these understandings. In order to address color's position in the design process and the importance of color in relation to space, form, and the experience of place, a selection of Queensland architects and interior designers were surveyed. The study is not conclusive, however, it does identify differences and commonalities between the participants that are of interest in light of the above issues. Explorations into environmental meaning, in addition to color theory and decorative applications, are hypothesized to be important sources of information for designers involved in the coloration of the built environment.

Lessons Learned from the 200 West Pump and Treatment Facility Construction Project at the US DOE Hanford Site - A Leadership for Energy and Environmental Design (LEED) Gold-Certified Facility - 13113

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorr, Kent A.; Freeman-Pollard, Jhivaun R.; Ostrom, Michael J.

CH2M Hill Plateau Remediation Company (CHPRC) designed, constructed, commissioned, and began operation of the largest groundwater pump and treatment facility in the U.S. Department of Energy's (DOE) nationwide complex. This one-of-a-kind groundwater pump and treatment facility, located at the Hanford Nuclear Reservation Site (Hanford Site) in Washington State, was built to an accelerated schedule with American Recovery and Reinvestment Act (ARRA) funds. There were many contractual, technical, configuration management, quality, safety, and Leadership in Energy and Environmental Design (LEED) challenges associated with the design, procurement, construction, and commissioning of this $95 million, 52,000 ft groundwater pump and treatment facility tomore » meet DOE's mission objective of treating contaminated groundwater at the Hanford Site with a new facility by June 28, 2012. The project team's successful integration of the project's core values and green energy technology throughout design, procurement, construction, and start-up of this complex, first-of-its-kind Bio Process facility resulted in successful achievement of DOE's mission objective, as well as attainment of LEED GOLD certification (Figure 1), which makes this Bio Process facility the first non-administrative building in the DOE Office of Environmental Management complex to earn such an award. (authors)« less

Thermal Design of the Instrument for the Transiting Exoplanet Survey Satellite

NASA Technical Reports Server (NTRS)

Allen, Gregory D.

2016-01-01

TESS observatory is a two year NASA Explorer mission which will use a set of four cameras to discover exoplanets. It will be placed in a high-earth orbit with a period of 13.7 days and will be unaffected by temperature disturbances caused by environmental heating from the Earth. The cameras use their stray-light baffles to passively cool the cameras and in turn the CCD's in order to maintain operational temperatures. The design has been well thought out and analyzed to maximize temperature stability. The analysis shows that the design keeps the cameras and their components within their temperature ranges which will help make it a successful mission. It will also meet its survival requirement of sustaining exposure to a five hour eclipse. Official validation and verification planning is underway and will be performed as the system is built up. It is slated for launch in 2017.

A unified design space of synthetic stripe-forming networks

PubMed Central

Schaerli, Yolanda; Munteanu, Andreea; Gili, Magüi; Cotterell, James; Sharpe, James; Isalan, Mark

2014-01-01

Synthetic biology is a promising tool to study the function and properties of gene regulatory networks. Gene circuits with predefined behaviours have been successfully built and modelled, but largely on a case-by-case basis. Here we go beyond individual networks and explore both computationally and synthetically the design space of possible dynamical mechanisms for 3-node stripe-forming networks. First, we computationally test every possible 3-node network for stripe formation in a morphogen gradient. We discover four different dynamical mechanisms to form a stripe and identify the minimal network of each group. Next, with the help of newly established engineering criteria we build these four networks synthetically and show that they indeed operate with four fundamentally distinct mechanisms. Finally, this close match between theory and experiment allows us to infer and subsequently build a 2-node network that represents the archetype of the explored design space. PMID:25247316

Mechanical design and fabrication of the VHF-gun, the Berkeley normal-conducting continuous-wave high-brightness electron source

NASA Astrophysics Data System (ADS)

Wells, R. P.; Ghiorso, W.; Staples, J.; Huang, T. M.; Sannibale, F.; Kramasz, T. D.

2016-02-01

A high repetition rate, MHz-class, high-brightness electron source is a key element in future high-repetition-rate x-ray free electron laser-based light sources. The VHF-gun, a novel low frequency radio-frequency gun, is the Lawrence Berkeley National Laboratory (LBNL) response to that need. The gun design is based on a normal conducting, single cell cavity resonating at 186 MHz in the VHF band and capable of continuous wave operation while still delivering the high accelerating fields at the cathode required for the high brightness performance. The VHF-gun was fabricated and successfully commissioned in the framework of the Advanced Photo-injector EXperiment, an injector built at LBNL to demonstrate the capability of the gun to deliver the required beam quality. The basis for the selection of the VHF-gun technology, novel design features, and fabrication techniques are described.

Mechanical design and fabrication of the VHF-gun, the Berkeley normal-conducting continuous-wave high-brightness electron source.

PubMed

Wells, R P; Ghiorso, W; Staples, J; Huang, T M; Sannibale, F; Kramasz, T D

2016-02-01

A high repetition rate, MHz-class, high-brightness electron source is a key element in future high-repetition-rate x-ray free electron laser-based light sources. The VHF-gun, a novel low frequency radio-frequency gun, is the Lawrence Berkeley National Laboratory (LBNL) response to that need. The gun design is based on a normal conducting, single cell cavity resonating at 186 MHz in the VHF band and capable of continuous wave operation while still delivering the high accelerating fields at the cathode required for the high brightness performance. The VHF-gun was fabricated and successfully commissioned in the framework of the Advanced Photo-injector EXperiment, an injector built at LBNL to demonstrate the capability of the gun to deliver the required beam quality. The basis for the selection of the VHF-gun technology, novel design features, and fabrication techniques are described.

Compact field color schlieren system for use in microgravity materials processing

NASA Technical Reports Server (NTRS)

Poteet, W. M.; Owen, R. B.

1986-01-01

A compact color schlieren system designed for field measurement of materials processing parameters has been built and tested in a microgravity environment. Improvements in the color filter design and a compact optical arrangement allowed the system described here to retain the traditional advantages of schlieren, such as simplicity, sensitivity, and ease of data interpretation. Testing was accomplished by successfully flying the instrument on a series of parabolic trajectories on the NASA KC-135 microgravity simulation aircraft. A variety of samples of interest in materials processing were examined. Although the present system was designed for aircraft use, the technique is well suited to space flight experimentation. A major goal of this effort was to accommodate the main optical system within a volume approximately equal to that of a Space Shuttle middeck locker. Future plans include the development of an automated space-qualified facility for use on the Shuttle and Space Station.

Passive isolation/damping system for the Hubble space telescope reaction wheels

NASA Technical Reports Server (NTRS)

Hasha, Martin D.

1987-01-01

NASA's Hubble Space Telescope contain large, diffraction limited optics with extraordinary resolution and performance for surpassing existing observatories. The need to reduce structural borne vibration and resultant optical jitter from critical Pointing Control System components, Reaction Wheels, prompted the feasibility investigation and eventual development of a passive isolation system. Alternative design concepts considered were required to meet a host of stringent specifications and pass rigid tests to be successfully verified and integrated into the already built flight vehicle. The final design employs multiple arrays of fluid damped springs that attenuate over a wide spectrum, while confining newly introduced resonances to benign regions of vehicle dynamic response. Overall jitter improvement of roughly a factor of 2 to 3 is attained with this system. The basis, evolution, and performance of the isolation system, specifically discussing design concepts considered, optimization studies, development lessons learned, innovative features, and analytical and ground test verified results are presented.

Research and Design on a Product Data Definition System of Semiconductor Packaging Industry

NASA Astrophysics Data System (ADS)

Shi, Jinfei; Ma, Qingyao; Zhou, Yifan; Chen, Ruwen

2017-12-01

This paper develops a product data definition (PDD) system for a semiconductor packaging and testing company with independent intellectual property rights. The new PDD system can solve the problems such as, the effective control of production plans, the timely feedback of production processes, and the efficient schedule of resources. Firstly, this paper introduces the general requirements of the PDD system and depicts the operation flow and the data flow of the PDD system. Secondly, the overall design scheme of the PDD system is put forward. After that, the physical data model is developed using the Power Designer15.0 tool, and the database system is built. Finally, the function realization and running effects of the PDD system are analysed. The successful operation of the PDD system can realize the information flow among various production departments of the enterprise to meet the standard of the enterprise manufacturing integration and improve the efficiency of production management.

eTRIKS platform: Conception and operation of a highly scalable cloud-based platform for translational research and applications development.

PubMed

Bussery, Justin; Denis, Leslie-Alexandre; Guillon, Benjamin; Liu, Pengfeï; Marchetti, Gino; Rahal, Ghita

2018-04-01

We describe the genesis, design and evolution of a computing platform designed and built to improve the success rate of biomedical translational research. The eTRIKS project platform was developed with the aim of building a platform that can securely host heterogeneous types of data and provide an optimal environment to run tranSMART analytical applications. Many types of data can now be hosted, including multi-OMICS data, preclinical laboratory data and clinical information, including longitudinal data sets. During the last two years, the platform has matured into a robust translational research knowledge management system that is able to host other data mining applications and support the development of new analytical tools. Copyright © 2018 Elsevier Ltd. All rights reserved.

Study of a non-equilibrium plasma pinch with application for microwave generation

NASA Astrophysics Data System (ADS)

Al Agry, Ahmad Farouk

The Non-Equilibrium Plasma Pinch (NEPP), also known as the Dense Plasma Focus (DPF) is well known as a source of energetic ions, relativistic electrons and neutrons as well as electromagnetic radiation extending from the infrared to X-ray. In this dissertation, the operation of a 15 kJ, Mather type, NEPP machine is studied in detail. A large number of experiments are carried out to tune the machine parameters for best performance using helium and hydrogen as filling gases. The NEPP machine is modified to be able to extract the copious number of electrons generated at the pinch. A hollow anode with small hole at the flat end, and a mock magnetron without biasing magnetic field are built. The electrons generated at the pinch are very difficult to capture, therefore a novel device is built to capture and transport the electrons from the pinch to the magnetron. The novel cup-rod-needle device successfully serves the purpose to capture and transport electrons to monitor the pinch current. Further, the device has the potential to field emit charges from its needle end acting as a pulsed electron source for other devices such as the magnetron. Diagnostics tools are designed, modeled, built, calibrated, and implemented in the machine to measure the pinch dynamics. A novel, UNLV patented electromagnetic dot sensors are successfully calibrated, and implemented in the machine. A new calibration technique is developed and test stands designed and built to measure the dot's ability to track the impetus signal over its dynamic range starting and ending in the noise region. The patented EM-dot sensor shows superior performance over traditional electromagnetic sensors, such as Rogowski coils. On the other hand, the cup-rod structure, when grounded on the rod side, serves as a diagnostic tool to monitor the pinch current by sampling the actual current, a quantity that has been always very challenging to measure without perturbing the pinch. To the best of our knowledge, this method of measuring the pinch current is unique and has never been done before. Agreement with other models is shown. The operation of the NEPP machine with the hole in the center of the anode and the magnetron connected including the cup-rod structure is examined against the NEPP machine signature with solid anode. Both cases showed excellent agreement. This suggests that the existence of the hole and the diagnostic tool inside the anode have negligible effects on the pinch.

The Neutron Star Interior Composition Explorer (NICER): Design and Development

NASA Technical Reports Server (NTRS)

Gendreau, Keith C.; Arzoumanian, Zaven; Adkins, Phillip W.; Albert, Cheryl L.; Anders, John F.; Aylward, Andrew T.; Baker, Charles L.; Balsamo, Erin R.; Bamford, William A.; Benegalrao, Suyog S.;

High altitude ballooning as a platform for student research experiences in science and engineering

NASA Astrophysics Data System (ADS)

Armstrong, John; Larson, Shane; Hiscock, Bill

2008-10-01

Humans have dreamed of sailing high above Earth's atmosphere and making the voyage into outer space. At the start of the 21st Century, our students can send their own research experiments from the surface of Earth to the fringes of outer space, borne aloft by high altitude balloons. Colloquially known as near-space platforms, these balloon systems are designed, constructed and own by the students themselves. They are inexpensive to construct, are built with common electronic and hardware components that are easily purchased from commercial vendors, and can be launched and recovered in a single day. The systems are reusable and can be own many times, allowing students to many new experiments during their student lifetime, or to a single experiment many times to acquire extended scientific data sets. We will focus the presentation on Weber State University's High Altitude Reconnaissance Balloon for Outreach and Research (HARBOR) that is based on the successful Montana State BOREALIS ballooning program. We will outline successful strategies for engaging undergraduate students in research and design using such programs.

The Neutron star Interior Composition Explorer (NICER): design and development

NASA Astrophysics Data System (ADS)

Gendreau, Keith C.; Arzoumanian, Zaven; Adkins, Phillip W.; Albert, Cheryl L.; Anders, John F.; Aylward, Andrew T.; Baker, Charles L.; Balsamo, Erin R.; Bamford, William A.; Benegalrao, Suyog S.; Berry, Daniel L.; Bhalwani, Shiraz; Black, J. Kevin; Blaurock, Carl; Bronke, Ginger M.; Brown, Gary L.; Budinoff, Jason G.; Cantwell, Jeffrey D.; Cazeau, Thoniel; Chen, Philip T.; Clement, Thomas G.; Colangelo, Andrew T.; Coleman, Jerry S.; Coopersmith, Jonathan D.; Dehaven, William E.; Doty, John P.; Egan, Mark D.; Enoto, Teruaki; Fan, Terry W.; Ferro, Deneen M.; Foster, Richard; Galassi, Nicholas M.; Gallo, Luis D.; Green, Chris M.; Grosh, Dave; Ha, Kong Q.; Hasouneh, Monther A.; Heefner, Kristofer B.; Hestnes, Phyllis; Hoge, Lisa J.; Jacobs, Tawanda M.; Jørgensen, John L.; Kaiser, Michael A.; Kellogg, James W.; Kenyon, Steven J.; Koenecke, Richard G.; Kozon, Robert P.; LaMarr, Beverly; Lambertson, Mike D.; Larson, Anne M.; Lentine, Steven; Lewis, Jesse H.; Lilly, Michael G.; Liu, Kuochia Alice; Malonis, Andrew; Manthripragada, Sridhar S.; Markwardt, Craig B.; Matonak, Bryan D.; Mcginnis, Isaac E.; Miller, Roger L.; Mitchell, Alissa L.; Mitchell, Jason W.; Mohammed, Jelila S.; Monroe, Charles A.; Montt de Garcia, Kristina M.; Mulé, Peter D.; Nagao, Louis T.; Ngo, Son N.; Norris, Eric D.; Norwood, Dwight A.; Novotka, Joseph; Okajima, Takashi; Olsen, Lawrence G.; Onyeachu, Chimaobi O.; Orosco, Henry Y.; Peterson, Jacqualine R.; Pevear, Kristina N.; Pham, Karen K.; Pollard, Sue E.; Pope, John S.; Powers, Daniel F.; Powers, Charles E.; Price, Samuel R.; Prigozhin, Gregory Y.; Ramirez, Julian B.; Reid, Winston J.; Remillard, Ronald A.; Rogstad, Eric M.; Rosecrans, Glenn P.; Rowe, John N.; Sager, Jennifer A.; Sanders, Claude A.; Savadkin, Bruce; Saylor, Maxine R.; Schaeffer, Alexander F.; Schweiss, Nancy S.; Semper, Sean R.; Serlemitsos, Peter J.; Shackelford, Larry V.; Soong, Yang; Struebel, Jonathan; Vezie, Michael L.; Villasenor, Joel S.; Winternitz, Luke B.; Wofford, George I.; Wright, Michael R.; Yang, Mike Y.; Yu, Wayne H.

2016-07-01

During 2014 and 2015, NASA's Neutron star Interior Composition Explorer (NICER) mission proceeded success- fully through Phase C, Design and Development. An X-ray (0.2-12 keV) astrophysics payload destined for the International Space Station, NICER is manifested for launch in early 2017 on the Commercial Resupply Services SpaceX-11 flight. Its scientific objectives are to investigate the internal structure, dynamics, and energetics of neutron stars, the densest objects in the universe. During Phase C, flight components including optics, detectors, the optical bench, pointing actuators, electronics, and others were subjected to environmental testing and integrated to form the flight payload. A custom-built facility was used to co-align and integrate the X-ray "con- centrator" optics and silicon-drift detectors. Ground calibration provided robust performance measures of the optical (at NASA's Goddard Space Flight Center) and detector (at the Massachusetts Institute of Technology) subsystems, while comprehensive functional tests prior to payload-level environmental testing met all instrument performance requirements. We describe here the implementation of NICER's major subsystems, summarize their performance and calibration, and outline the component-level testing that was successfully applied.

Fastrac Nozzle Design, Performance and Development

NASA Technical Reports Server (NTRS)

Peters, Warren; Rogers, Pat; Lawrence, Tim; Davis, Darrell; DAgostino, Mark; Brown, Andy

2000-01-01

With the goal of lowering the cost of payload to orbit, NASA/MSFC (Marshall Space Flight Center) researched ways to decrease the complexity and cost of an engine system and its components for a small two-stage booster vehicle. The composite nozzle for this Fastrac Engine was designed, built and tested by MSFC with fabrication support and engineering from Thiokol-SEHO (Science and Engineering Huntsville Operation). The Fastrac nozzle uses materials, fabrication processes and design features that are inexpensive, simple and easily manufactured. As the low cost nozzle (and injector) design matured through the subscale tests and into full scale hot fire testing, X-34 chose the Fastrac engine for the propulsion plant for the X-34. Modifications were made to nozzle design in order to meet the new flight requirements. The nozzle design has evolved through subscale testing and manufacturing demonstrations to full CFD (Computational Fluid Dynamics), thermal, thermomechanical and dynamic analysis and the required component and engine system tests to validate the design. The Fastrac nozzle is now in final development hot fire testing and has successfully accumulated 66 hot fire tests and 1804 seconds on 18 different nozzles.

An Analysis of the Advantages and Disadvantages of the Air Force Standard Control Panel

DTIC Science & Technology

1989-09-01

comparativ - process. The built-up system required approximately 100 hours to design , install and calibrate. The reader is reminded that the built-up...Summary......................................... 9 Outline of Research Design .................... 9 Ii. Literature Review...133 Question 3 .......................... 133 Area 3: Design Phase ................... 134 Question 4 .......................... 134 Area 4

A Design Model: The Autism Spectrum Disorder Classroom Design Kit

ERIC Educational Resources Information Center

McAllister, Keith; Maguire, Barry

2012-01-01

Architects and designers have a responsibility to provide an inclusive built environment. However, for those with a diagnosis of autism spectrum disorder (ASD), the built environment can be a frightening and confusing place, difficult to negotiate and tolerate. The challenge of integrating more fully into society is denied by an alienating built…

National Built Environment Health Impact Assessment Model ...

EPA Pesticide Factsheets

Behavioral (activity, diet, social interaction) and exposure (air pollution, traffic injury, and noise) related health impacts of land use and transportation investment decisions are becoming better understood and quantified. Research has shown relationships between density, mix, street connectivity, access to parks, shops, transit, presence of sidewalks and bikeways, and healthy food with physical activity, obesity, cardiovascular disease, type II diabetes, and some mental health outcomes. This session demonstrates successful integration of health impact assessment into multiple scenario planning tool platforms. Detailed evidence on chronic disease and related costs associated with contrasting land use and transportation investments are built into a general-purpose module that can be accessed by multiple platforms. Funders, researchers, and end users of the tool will present a detailed description of the key elements of the approach, how it has been applied, and how will evolve. A critical focus will be placed on equity and social justice inherent within the assessment of health disparities that will be featured in the session. Health impacts of community design have significant cost benefit implications. Recent research is now extending relationships between community design features and chronic disease to health care costs. This session will demonstrate the recent application of this evidence on health impacts to the newly adopted Los Angeles Regional Transpo

Role of Educational Strategies for Human Resources in Green Infrastructure Operation and Maintenance

NASA Astrophysics Data System (ADS)

Ebrahimi, G.; Thurm, B.; Öberg, G.

2014-12-01

Rainwater harvesting and water reuse are receiving increasing attention as they hold the potential to effectively improve water conservation efforts. While many technical solutions have been developed, alternative water systems in built environments face significant challenges in the implementation and operational phases. The aim of this study is to examine obstacles to the implementation of alternative water systems in practice and identify criteria of feasible and sustainable solutions that allow bypassing of the identified obstacles. Interviews were conducted with planners, system designers and operators to find out which factors that central actors believe influence successful implementation of such systems. The results were analyzed in light of the literature. The actual performance of the water harvesting and reuse systems in four recently built green buildings in the Province of British Columbia, Canada was analyzed in light of the predicted outcome, according to the criteria identified in the interviews. It was found that the major obstacle to success is that the practical challenges involved in the implementation of alternative systems are underestimated. This, for example, leads to that education strategies for operational staff are not developed, and the staff is left floundering. This study highlights the importance of recognizing the need for strategic and directed educational programs for the human resources who are involved in operating and maintaining rainwater harvesting and water reuse systems.

Achieving cooperative success

Treesearch

Kimberly Zeuli

2006-01-01

Success of a cooperative depends on the foundation built during its organization. Successful businesses are not started overnight. Careful and deliberate planning must be started long before the co-op opens its doors. This chapter begins with an outline of six fundamental steps that should be followed when organizing any cooperative. From initial concept to the start...

Factors impeding flexible inpatient unit design.

PubMed

Pati, Debajyoti; Evans, Jennie; Harvey, Thomas E; Bazuin, Doug

2012-01-01

To identify and examine factors extraneous to the design decision-making process that could impede the optimization of flexibility on inpatient units. A 2006 empirical study to identify domains of design decisions that affect flexibility on inpatient units found some indication in the context of the acuity-adaptable operational model that factors extraneous to the design process could have negatively influenced the successful implementation of the model. This raised questions regarding extraneous factors that might influence the successful optimization of flexibility. An exploratory, qualitative method was adopted to examine the question. Stakeholders from five recently built acute care inpatient units participated in the study, which involved three types of data collection: (1) verbal protocol data from a gaming session; (2) in-depth semi-structured interviews; and (3) shadowing frontline personnel. Data collection was conducted between June 2009 and November 2010. The study revealed at least nine factors extraneous to the design process that have the potential to hinder the optimization of flexibility in four domains: (1) systemic; (2) cultural; (3) human; and (4) financial. Flexibility is critical to hospital operations in the new healthcare climate, where cost reduction constitutes a vital target. From this perspective, flexibility and efficiency strategies can be influenced by (1) return on investment, (2) communication, (3) culture change, and (4) problem definition. Extraneous factors identified in this study could also affect flexibility in other care settings; therefore, these findings may be viewed from the overall context of hospital design.

Uncertainty quantification-based robust aerodynamic optimization of laminar flow nacelle

NASA Astrophysics Data System (ADS)

Xiong, Neng; Tao, Yang; Liu, Zhiyong; Lin, Jun

2018-05-01

The aerodynamic performance of laminar flow nacelle is highly sensitive to uncertain working conditions, especially the surface roughness. An efficient robust aerodynamic optimization method on the basis of non-deterministic computational fluid dynamic (CFD) simulation and Efficient Global Optimization (EGO)algorithm was employed. A non-intrusive polynomial chaos method is used in conjunction with an existing well-verified CFD module to quantify the uncertainty propagation in the flow field. This paper investigates the roughness modeling behavior with the γ-Ret shear stress transport model including modeling flow transition and surface roughness effects. The roughness effects are modeled to simulate sand grain roughness. A Class-Shape Transformation-based parametrical description of the nacelle contour as part of an automatic design evaluation process is presented. A Design-of-Experiments (DoE) was performed and surrogate model by Kriging method was built. The new design nacelle process demonstrates that significant improvements of both mean and variance of the efficiency are achieved and the proposed method can be applied to laminar flow nacelle design successfully.

Design of Backpack to Aid Elderly for the Mazu Touring Procession in Taiwan

NASA Astrophysics Data System (ADS)

Chao, F. L.; Huang, Y. C.; Su, J. Y.; Sun, C. L.; Chen, C. C.

2017-09-01

The Dajia Mazu Touring Procession is a 9-day long religious event held annually. However, for the elderly participants, it is a big burden especially in regards to physical strength. The goal of designing backpack is to reduce the physiological stress of elderly during the procession. Firstly, physical parameters were measured to explore the dimension parameters by testing. The height of the chair is different from that of the kneeling pad; a smooth curve was chosen to coordinate the two as the main outline of the backpack. Secondly, material selections based on following limits were considered: (1) acceptable weight and size, (2) intermediate price and (3) a design that is fitting to the Dajia event. The material and structural strength were evaluated for wood, bamboo, stainless steel. Two design concept were proposed, wood is selected for construction and testing by users. The texture of the backpack is Rush grass, it was built successfully to cover the backpack’s external surface to meet local culture features.

Testing Hypothesized Psychosocial Mediators: Lessons Learned in the MassBUILT Study

ERIC Educational Resources Information Center

Okechukwu, Cassandra A.; Krieger, Nancy; Sorensen, Glorian; Li, Yi; Barbeau, Elizabeth M.

2011-01-01

Only a few of the interventions that target blue-collar workers have conducted formal analysis to evaluate the specific attributes of their intervention that are associated with success or failure. This study examined the role of dual hazard and decisional balance in the MassBUILT smoking cessation intervention. The authors conducted sets of…

Lost in the Labyrinthine Library: A Multi-Method Case Study Investigating Public Library User Wayfinding Behavior

ERIC Educational Resources Information Center

Mandel, Lauren Heather

2012-01-01

Wayfinding is the method by which humans orient and navigate in space, and particularly in built environments such as cities and complex buildings, including public libraries. In order to wayfind successfully in the built environment, humans need information provided by wayfinding systems and tools, for instance architectural cues, signs, and…

Pathfinding the Flight Advanced Stirling Convertor Design with the ASC-E3

NASA Technical Reports Server (NTRS)

Wong, Wayne A.; Wilson, Kyle; Smith, Eddie; Collins, Josh

2012-01-01

The Advanced Stirling Convertor (ASC) was initially developed by Sunpower, Inc. under contract to NASA Glenn Research Center (GRC) as a technology development project. The ASC technology fulfills NASA's need for high efficiency power convertors for future Radioisotope Power Systems (RPS). Early successful technology demonstrations between 2003 to 2005 eventually led to the expansion of the project including the decision in 2006 to use the ASC technology on the Advanced Stirling Radioisotope Generator (ASRG). Sunpower has delivered 22 ASC convertors of progressively mature designs to date to GRC. Currently, Sunpower with support from GRC, Lockheed Martin Space System Company (LMSSC), and the Department of Energy (DOE) is developing the flight ASC-F in parallel with the ASC-E3 pathfinders. Sunpower will deliver four pairs of ASC-E3 convertors to GRC which will be used for extended operation reliability assessment, independent validation and verification testing, system interaction tests, and to support LMSSC controller verification. The ASC-E3 and -F convertors are being built to the same design and processing documentation and the same product specification. The initial two pairs of ASC-E3 are built before the flight units and will validate design and processing changes prior to implementation on the ASC-F flight convertors. This paper provides a summary on development of the ASC technology and the status of the ASC-E3 build and how they serve the vital pathfinder role ahead of the flight build for ASRG. The ASRG is part of two of the three candidate missions being considered for selection for the Discovery 12 mission.

Compact Optical Correlators

NASA Astrophysics Data System (ADS)

Gregory, Don A.; Kirsch, James C.

1989-02-01

In the past 15 years, a dozen or so designs have been proposed for compact optical correlators. Of these, maybe one-third of them have actually been built and only a few of those tested. This paper will give an overview of some of the systems that have been built as well as mention some promising early and current designs that have not been built. The term compact, as used in the title of this paper, will be applied very loosely; to mean smaller than a laboratory size optical table. To date, only one correlator has been built and tested that actually can be called miniature. This softball size correlator was built by the Perkin-Elmer Corporation for the U. S. Army Missile Command at Redstone Arsenal, Alabama. More will be said about this correlator in following sections.

Experimental feasibility study of the application of magnetic suspension techniques to large-scale aerodynamic test facilities

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1974-01-01

Based on the premises that (1) magnetic suspension techniques can play a useful role in large-scale aerodynamic testing and (2) superconductor technology offers the only practical hope for building large-scale magnetic suspensions, an all-superconductor three-component magnetic suspension and balance facility was built as a prototype and was tested successfully. Quantitative extrapolations of design and performance characteristics of this prototype system to larger systems compatible with existing and planned high Reynolds number facilities have been made and show that this experimental technique should be particularly attractive when used in conjunction with large cryogenic wind tunnels.

Development of an adsorption compressor for use in cryogenic refrigeration

NASA Technical Reports Server (NTRS)

Schember, Helen R.

1989-01-01

A new compressor with no moving parts has been developed which is able to supply a source of high-pressure gas to a Joule-Thompson based cryogenic refrigerator. The compressor relies on a newly implemented combination of high-surface-area Saran carbon (sorbent) and krypton gas (working fluid). In addition, an integral gas-gap heat switch is used to provide improved overall efficiency. A prototype compressor has been designed, built, and tested as a part of the Jet Propulsion Laboratory effort in sorption refrigeration. Performance data from the prototype unit described here demonstrate successful compressor performance and good agreement with theoretical predictions.

Dynamic testing system for hybrid magneto-optical recording

NASA Astrophysics Data System (ADS)

Chen, Lu; Xu, Wendong; Fan, Yongtao; Zhu, Qing

2008-12-01

Hybrid Magneto-Optical Recording is a potential data storage technology in the future informational society. To construct a research platform for hybrid recording, a dynamic testing system is designed and built in this paper, in which 406.7nm blue laser is used for recording and 655nm red laser for focus servo. With high modularization, the computer serves as the control core for the laser external modulation, focus servo, and sample plate spinning. Each module and its function are discussed in detail in the paper. Experimental results are also given to verify the stable and smooth performance of the system, in which the key obstacle, vibration noise, is successfully surmounted.

Development of closed loop roll control for magnetic balance systems

NASA Technical Reports Server (NTRS)

Covert, E. E.; Haldeman, C. W.; Ramohalli, G.; Way, P.

1982-01-01

This research was undertaken with the goal of demonstrating closed loop control of the roll degree of freedom on the NASA prototype magnetic suspension and balance system at the MIT Aerophysics Laboratory, thus, showing feasibility for a roll control system for any large magnetic balance system which might be built in the future. During the research under this grant, study was directed toward the several areas of torque generation, position sensing, model construction and control system design. These effects were then integrated to produce successful closed loop operation of the analogue roll control system. This experience indicated the desirability of microprocessor control for the angular degrees of freedom.

Beam acceleration through proton radio frequency quadrupole accelerator in BARC

NASA Astrophysics Data System (ADS)

Bhagwat, P. V.; Krishnagopal, S.; Mathew, J. V.; Singh, S. K.; Jain, P.; Rao, S. V. L. S.; Pande, M.; Kumar, R.; Roychowdhury, P.; Kelwani, H.; Rama Rao, B. V.; Gupta, S. K.; Agarwal, A.; Kukreti, B. M.; Singh, P.

2016-05-01

A 3 MeV proton Radio Frequency Quadrupole (RFQ) accelerator has been designed at the Bhabha Atomic Research Centre, Mumbai, India, for the Low Energy High Intensity Proton Accelerator (LEHIPA) programme. The 352 MHz RFQ is built in 4 segments and in the first phase two segments of the LEHIPA RFQ were commissioned, accelerating a 50 keV, 1 mA pulsed proton beam from the ion source, to an energy of 1.24 MeV. The successful operation of the RFQ gave confidence in the physics understanding and technology development that have been achieved, and indicate that the road forward can now be traversed rather more quickly.

Acceptance and introduction of disruptive technologies - simple steps to build a fully functional pulmonary valved stent.

PubMed

Huber, Christoph H; Marty, Bettina; von Segesser, Ludwig K

2007-08-01

Valved stents are new land for cardiac surgeons even though they are being used more frequently by interventional disciplines. This paper presents simple steps to build a patient-specific pulmonary valved stent and its delivery device. The design concept was tested by random participants at a med-tech meeting. The valved stent is constructed by linking an endoprosthetic graft with a valved-jugular-vein. The delivery device is made from a modified 5-ml syringe. Of 72 participants, 66 (92%) built and 60 participants implanted the device successfully into the targeted pulmonary position via a trans-infundibular access.

Computational modeling and experimental studies on NO{sub x} reduction under pulverized coal combustion conditions. Seventh quarterly technical progress report, July 1, 1996--September 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumpaty, S.K.; Subramanian, K.; Nokku, V.P.

1996-12-31

During this quarter (July-August 1996), the experiments for nitric oxide reburning with a combination of methane and ammonia were conducted successfully. This marked the completion of gaseous phase experiments. Preparations are underway for the reburning studies with coal. A coal feeder was designed to suit our reactor facility which is being built by MK Fabrication. The coal feeder should be operational in the coming quarter. Presented here are the experimental results of NO reburning with methane/ammonia. The results are consistent with the computational work submitted in previous reports.

A Radio-Frequency-over-Fiber link for large-array radio astronomy applications

NASA Astrophysics Data System (ADS)

Mena, J.; Bandura, K.; Cliche, J.-F.; Dobbs, M.; Gilbert, A.; Tang, Q. Y.

2013-10-01

A prototype 425-850 MHz Radio-Frequency-over-Fiber (RFoF) link for the Canadian Hydrogen Intensity Mapping Experiment (CHIME) is presented. The design is based on a directly modulated Fabry-Perot (FP) laser, operating at ambient temperature, and a single-mode fiber. The dynamic performance, gain stability, and phase stability of the RFoF link are characterized. Tests on a two-element interferometer built at the Dominion Radio Astrophysical Observatory for CHIME prototyping demonstrate that RFoF can be successfully used as a cost-effective solution for analog signal transport on the CHIME telescope and other large-array radio astronomy applications.

Operating experience of the southwire high-temperature superconducting cable project

NASA Astrophysics Data System (ADS)

Hughey, R. L.; Lindsay, D.

2002-01-01

Southwire Company of Carrollton, Georgia in cooperation with Oak Ridge National Laboratory has designed, built, installed and is operating the world's first field installation of a High Temperature Superconducting (HTS) cable system. The cables supply power to three Southwire manufacturing facilities and part of the corporate headquarters building in Carrollton, GA. The system consists of three 30-m single phase cables rated at 12.4 kV, 1250 Amps, liquid nitrogen cooling system, and the computer-based control system. The cables are built using BSCCO-2223 powder-in-tube HTS tapes and a proprietary cryogenic dielectric material called Cryoflex™. The cables are fully shielded with a second layer of HTS tapes to eliminate any external magnetic fields. The Southwire HTS cables were first energized on january 6, 2000. Since that time they have logged over 8,500 hours of operation while supplying 100% of the required customer load. To date, the cables have worked without failure and operations are continuing. The cable design has passed requisite testing for this class of conventional cables including 10× over current to 12,500 Amps and BIL testing to 110 kV. Southwire has also successfully designed and tested a cable splice. System heat loads and AC Losses have been measured and compared to calculated values. On June 1, 2001 on-site monitoring was ceased and the system was changed to unattended operation to further prove the reliability of the HTS cable system. .

Measurement of vortex flow fields

NASA Technical Reports Server (NTRS)

Mcdevitt, T. Kevin; Ambur, Todd A.; Orngard, Gary M.; Owen, F. Kevin

1992-01-01

A 3-D laser fluorescence anemometer (LFA) was designed, built, and demonstrated for use in the Langley 16 x 24 inch Water Tunnel. Innovative optical design flexibility combined with compact and portable data acquisition and control systems were incorporated into the instrument. This will allow its use by NASA in other test facilities. A versatile fiber optic system facilities normal and off-axis laser beam alignment, removes mirror losses and improves laser safety. This added optical flexibility will also enable simple adaptation for use in the adjacent jet facility. New proprietary concepts in transmitting color separation, light collection, and novel prism separation of the scattered light was also designed and built into the system. Off-axis beam traverse and alignment complexity led to the requirement for a specialized, programmable transverse controller, and the inclusion of an additional traverse for the off-axis arm. To meet this challenge, an 'in-house' prototype unit was designed and built and traverse control software developed specifically for the water tunnel traverse applications. A specialized data acquisition interface was also required. This was designed and built for the LFA system.

Freight Advanced Traveler Information System (FRATIS) – Dallas-Fort Worth : as-built system architecture and design.

DOT National Transportation Integrated Search

2015-03-01

This document describes the As-Built System Architecture and Design for the FRATIS Dallas-Fort Worth DFW prototype system. The FRATIS prototype in DFW consisted of the following components: optimization algorithm, terminal wait time, route specific n...

On the Cutting Edge Professional Development Program - An effective model built from years of experience

NASA Astrophysics Data System (ADS)

Bruckner, M. Z.; Macdonald, H.; Beane, R. J.; Manduca, C. A.; Mcconnell, D. A.; Mogk, D. W.; Tewksbury, B. J.; Wiese, K.; Wysession, M. E.; Iverson, E. A. R.; Fox, S.

2015-12-01

The On the Cutting Edge (CE) program offers a successful model for designing and convening professional development events. Information about the model is now available on the CE website. The program model has evolved from more than 12 years of experience, building with input from strong leaders and participants. CE offers face-to-face, virtual, and hybrid events, and features a rich website that supports these professional development events as well as a growing community with a shared interest in effective geoscience teaching. Data from national surveys, participant feedback, and self-report data indicate the program's success in improving undergraduate geoscience education. Successes are also demonstrated in classroom observations using RTOP, indicating a significant difference in teaching style among participants and non-participants. A suite of web pages, with a planning timeline, provides guidance to those interested in designing and convening face-to-face or virtual events based on the CE model. The pages suggest ways to develop robust event goals and evaluation tools, how to choose strong leaders and recruit diverse participants, advice for designing effective event programs that utilize participant expertise, websites, and web tools, and suggestions for effectively disseminating event results and producing useful products. The CE model has been successfully transferred to projects that vary in scale and discipline. Best practices from the CE model include (1) thinking of the workshop as shared enterprise among conveners and participants; (2) incorporating conveners and participants who bring diverse viewpoints and approaches; (3) promoting structured discussions that utilize participants' expertise; (4) emphasizing practical strategies to effect change; and (5) using the website as a platform to prepare for the workshop, share ideas, and problem-solve challenges. Learn more about how to utilize this model for your project at:serc.carleton.edu/NAGTWorkshops/workshops/convene

Fabrication and test of a space power boiler feed electromagnetic pump. Part 2: Test facility and performance test

NASA Technical Reports Server (NTRS)

Powell, A. H.; Amos, J. C.; Ehde, C. L.; Gahan, J. W.

1972-01-01

A three-phase helical induction electromagnetic pump, designed for the boiler-feed pump of a potassium Rankine-cycle space power system, was built and tested. The pump was tested over a range of potassium temperatures from 900 to 1400 F, flow rates from 0.75 to 4.85 lb/sec, developed pressures up to 340 psi, net positive suction heads (NPSH) from 1 to 22 psi, and NaK coolant temperatures from 800 to 950 F. The maximum efficiency at the pump design point of 3.25 lb/sec flow rate, 240 psi developed pressure, 1000 F potassium inlet temperature, and 800 F NaK coolant temperature was 16.3 percent. The tests also showed successful operation of the pump at an NPSH as low as 1.5 psi without cavitating.

A novel drill design for photoacoustic guided surgeries

NASA Astrophysics Data System (ADS)

Shubert, Joshua; Lediju Bell, Muyinatu A.

2018-02-01

Fluoroscopy is currently the standard approach for image guidance of surgical drilling procedures. In addition to the harmful radiation dose to the patient and surgeon, fluoroscopy fails to visualize critical structures such as blood vessels and nerves within the drill path. Photoacoustic imaging is a well-suited imaging method to visualize these structures and it does not require harmful ionizing radiation. However, there is currently no clinical system available to deliver light to occluded drill bit tips. To address this challenge, a prototype drill was designed, built, and tested using an internal light delivery system that allows laser energy to be transferred from a stationary laser source to the tip of a spinning drill bit. Photoacoustic images were successfully obtained with the drill bit submerged in water and with the drill tip inserted into a thoracic vertebra from a human cadaver.

Characterization of a low concentrator photovoltaics module

NASA Astrophysics Data System (ADS)

Butler, B. A.; van Dyk, E. E.; Vorster, F. J.; Okullo, W.; Munji, M. K.; Booysen, P.

2012-05-01

Low concentration photovoltaic (LCPV) systems have the potential to reduce the cost per kWh of electricity compared to conventional flat-plate photovoltaics (PV) by up to 50%. The cost-savings are realised by replacing expensive PV cells with relatively cheaper optical components to concentrate incident solar irradiance onto a receiver and by tracking the sun along either 1 axis or 2 axes. A LCPV module consists of three interrelated subsystems, viz., the optical, electrical and the thermal subsystems, which must be considered for optimal module design and performance. Successful integration of these subsystems requires the balancing of cost, performance and reliability. In this study LCPV experimental prototype modules were designed, built and evaluated with respect to optimisation of the three subsystems and overall performance. This paper reports on the optical and electrical evaluation of a prototype LCPV module.

ASPIRE - Airborne Spectro-Polarization InfraRed Experiment

NASA Astrophysics Data System (ADS)

DeLuca, E.; Cheimets, P.; Golub, L.; Madsen, C. A.; Marquez, V.; Bryans, P.; Judge, P. G.; Lussier, L.; McIntosh, S. W.; Tomczyk, S.

2017-12-01

Direct measurements of coronal magnetic fields are critical for taking the next step in active region and solar wind modeling and for building the next generation of physics-based space-weather models. We are proposing a new airborne instrument to make these key observations. Building on the successful Airborne InfraRed Spectrograph (AIR-Spec) experiment for the 2017 eclipse, we will design and build a spectro-polarimeter to measure coronal magnetic field during the 2019 South Pacific eclipse. The new instrument will use the AIR-Spec optical bench and the proven pointing, tracking, and stabilization optics. A new cryogenic spectro-polarimeter will be built focusing on the strongest emission lines observed during the eclipse. The AIR-Spec IR camera, slit jaw camera and data acquisition system will all be reused. The poster will outline the optical design and the science goals for ASPIRE.

An Adverse Drug Event and Medication Error Reporting System for Ambulatory Care (MEADERS)

PubMed Central

Zafar, Atif; Hickner, John; Pace, Wilson; Tierney, William

2008-01-01

The Institute of Medicine (IOM) has identified the mitigation of Adverse Drug Events (ADEs) and Medication Errors (MEs) as top national priorities. Currently available reporting tools are fraught with inefficiencies that prevent widespread adoption into busy primary care practices. Using expert panel input we designed and built a new reporting tool that could be used in these settings with a variety of information technology capabilities. We pilot tested the system in four Practice Based Research Networks (PBRNs) comprising 24 practices. Over 10 weeks we recorded 507 reports, of which 370 were MEs and 137 were ADEs. Clinicians found the system easy to use, with the average time to generating a report under 4 minutes. By using streamlined interface design techniques we were successfully able to improve reporting rates of ADEs and MEs in these practices. PMID:18999053

HIDRA-MAT: A Material Analysis Tool for Fusion Devices

NASA Astrophysics Data System (ADS)

Andruczyk, Daniel; Rizkallah, Rabel; Bedoya, Felipe; Kapat, Aveek; Schamis, Hanna; Allain, Jean Paul

2017-10-01

The former WEGA stellarator which is now operating as HIDRA at the University of Illinois will be almost exclusively used to study the intimate relationship between the plasma interacting with surfaces of different materials. A Material Analysis Tool (HIDRA-MAT) is being designed and will be built based on the successful Material Analysis and Particle Probe (MAPP) which is currently used on NSTX-U at PPPL. This will be an in-situ material diagnostic probe, meaning that all analysis can be done without breaking vacuum. This allows surface changes to be studied in real-time. HIDRA-MAT will consist of several in-situ diagnostics including Langmuir probes (LP), Thermal Desorption Spectroscopy (TDS), X-ray Photo Spectroscopy (XPS) and Ion Scattering Spectroscopy (ISS). This presentation will outline the HIDRA-MAT diagnostic and initial design, as well as its integration into the HIDRA system.

The Built Environment and Its Relationship to the Public’s Health: The Legal Framework

PubMed Central

Perdue, Wendy Collins; Stone, Lesley A.; Gostin, Lawrence O.

2003-01-01

The built environment significantly affects the public’s health. This was most obvious when infectious disease was the primary public health threat during the industrial revolution; unsanitary conditions and overcrowded urban areas facilitated the spread of infection. However, even today in the age of chronic diseases there remains an important connection between population health and the built environment. Physical spaces can expose people to toxins or pollutants and influence lifestyles that contribute to diabetes, coronary vascular disease, and asthma. Public health advocates can help shape the design of cities and suburbs in ways that improve public health, but to do so effectively they need to understand the legal framework. This article reviews the connection between public health and the built environment and then describes the legal pathways for improving the design of our built environment. PMID:12948949

Comparing the appropriate geographic region for assessing built environmental correlates with walking trips using different metrics and model approaches

PubMed Central

Tribby, Calvin P.; Miller, Harvey J.; Brown, Barbara B.; Smith, Ken R.; Werner, Carol M.

2017-01-01

There is growing international evidence that supportive built environments encourage active travel such as walking. An unsettled question is the role of geographic regions for analyzing the relationship between the built environment and active travel. This paper examines the geographic region question by assessing walking trip models that use two different regions: walking activity spaces and self-defined neighborhoods. We also use two types of built environment metrics, perceived and audit data, and two types of study design, cross-sectional and longitudinal, to assess these regions. We find that the built environment associations with walking are dependent on the type of metric and the type of model. Audit measures summarized within walking activity spaces better explain walking trips compared to audit measures within self-defined neighborhoods. Perceived measures summarized within self-defined neighborhoods have mixed results. Finally, results differ based on study design. This suggests that results may not be comparable among different regions, metrics and designs; researchers need to consider carefully these choices when assessing active travel correlates. PMID:28237743

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). As-Designed Parts List: Electrical, Electronic, and Electromechanical (EEE) As-Built Parts List for the AMSU-A Instruments

NASA Technical Reports Server (NTRS)

2000-01-01

This is the As-Designed Parts List, Electrical, Electronic, and Electromechanical (EEE) As-Built Parts Lists For The AMSU-A Instruments, for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A).

46 CFR 153.483 - Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1, 1986...

Code of Federal Regulations, 2010 CFR

2010-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.483 Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1...

46 CFR 153.480 - Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986: Categories...

Code of Federal Regulations, 2012 CFR

2012-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.480 Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986...

46 CFR 153.480 - Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986: Categories...

Code of Federal Regulations, 2013 CFR

2013-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.480 Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986...

46 CFR 153.480 - Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986: Categories...

Code of Federal Regulations, 2014 CFR

2014-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.480 Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986...

46 CFR 153.483 - Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1, 1986...

Code of Federal Regulations, 2014 CFR

2014-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.483 Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1...

46 CFR 153.480 - Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986: Categories...

Code of Federal Regulations, 2010 CFR

2010-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.480 Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986...

46 CFR 153.480 - Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986: Categories...

Code of Federal Regulations, 2011 CFR

2011-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.480 Stripping quantity for Category B and C NLS tanks on ships built after June 30, 1986...

46 CFR 153.483 - Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1, 1986...

Code of Federal Regulations, 2011 CFR

2011-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.483 Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1...

46 CFR 153.483 - Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1, 1986...

Code of Federal Regulations, 2012 CFR

2012-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.483 Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1...

46 CFR 153.483 - Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1, 1986...

Code of Federal Regulations, 2013 CFR

2013-10-01

..., LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and Equipment Design and Equipment for Pollution Control § 153.483 Restricted voyage waiver for Category B and C NLS tanks on ships built before July 1...

Bi-Axial Solar Array Drive Mechanism: Design, Build and Environmental Testing

NASA Technical Reports Server (NTRS)

Scheidegger, Noemy; Ferris, Mark; Phillips, Nigel

2014-01-01

The development of the Bi-Axial Solar Array Drive Mechanism (BSADM) presented in this paper is a demonstration of SSTL's unique space manufacturing approach that enables performing rapid development cycles for cost-effective products that meet ever-challenging mission requirements: The BSADM is designed to orient a solar array wing towards the sun, using its first rotation axis to track the sun, and its second rotation axis to compensate for the satellite orbit and attitude changes needed for a successful payload operation. The tight development schedule, with manufacture of 7 Flight Models within 1.5 year after kick-off, is offset by the risk-reduction of using qualified key component-families from other proven SSTL mechanisms. This allowed focusing the BSADM design activities on the mechanism features that are unique to the BSADM, and having an Engineering Qualification Model (EQM) built 8 months after kick-off. The EQM is currently undergoing a full environmental qualification test campaign. This paper presents the BSADM design approach that enabled meeting such a challenging schedule, its design particularities, and the ongoing verification activities.

Design and Testing of a Blended Wing Body With Boundary Layer Ingestion Nacelles at High Reynolds Numbers

NASA Technical Reports Server (NTRS)

Campbell, Richard L.; Carter, Melissa B.; Pendergraft, Odis C., Jr.; Friedman, Douglas M.; Serrano, Leonel

2005-01-01

A knowledge-based aerodynamic design method coupled with an unstructured grid Navier-Stokes flow solver was used to improve the propulsion/airframe integration for a Blended Wing Body with boundary-layer ingestion nacelles. A new zonal design capability was used that significantly reduced the time required to achieve a successful design for each nacelle and the elevon between them. A wind tunnel model was built with interchangeable parts reflecting the baseline and redesigned configurations and tested in the National Transonic Facility (NTF). Most of the testing was done at the cruise design conditions (Mach number = 0.85, Reynolds number = 75 million). In general, the predicted improvements in forces and moments as well as the changes in wing pressures between the baseline and redesign were confirmed by the wind tunnel results. The effectiveness of elevons between the nacelles was also predicted surprisingly well considering the crudeness in the modeling of the control surfaces in the flow code. A novel flow visualization technique involving pressure sensitive paint in the cryogenic nitrogen environment used in high-Reynolds number testing in the NTF was also investigated.

The process of aging: A case study approach implementing an ergonomics evaluation of the built environment for the elderly in Brazil.

PubMed

Paiva, Marie; Ferrer, Nicole; Villarouco, Vilma

2015-01-01

The phenomenon of aging is increasing worldwide. Various problems accompany it since aging makes the elderly undergo a decline in their natural functions. As such, senility can present itself as a barrier for everyday activities. This article presents a research that deals with the study of collective residences for the elderly. It seeks to identify configurations of these homes by seeking shortcomings and/or successful solutions. The Ergonomic Methodology for the Built Environment was applied. The method of the approach is qualitative and consists of multi-case study. Through the methodological approach, conflicts in the environment created by missing or inadequate elements were identified. Also, the opinions and suggestions from the elderly were analyzed, which shows their perception of the environment in use. The situations detected in this study indicate the occurrence of problems, exacerbated by the multiple deficiencies found in the user population of the environments analyzed. Thus it highlights the importance of there being future studies that are better targeted on designing environments for the elderly.

Controlling Tensegrity Robots Through Evolution

NASA Technical Reports Server (NTRS)

Iscen, Atil; Agogino, Adrian; SunSpiral, Vytas; Tumer, Kagan

2013-01-01

Tensegrity structures (built from interconnected rods and cables) have the potential to offer a revolutionary new robotic design that is light-weight, energy-efficient, robust to failures, capable of unique modes of locomotion, impact tolerant, and compliant (reducing damage between the robot and its environment). Unfortunately robots built from tensegrity structures are difficult to control with traditional methods due to their oscillatory nature, nonlinear coupling between components and overall complexity. Fortunately this formidable control challenge can be overcome through the use of evolutionary algorithms. In this paper we show that evolutionary algorithms can be used to efficiently control a ball-shaped tensegrity robot. Experimental results performed with a variety of evolutionary algorithms in a detailed soft-body physics simulator show that a centralized evolutionary algorithm performs 400 percent better than a hand-coded solution, while the multi-agent evolution performs 800 percent better. In addition, evolution is able to discover diverse control solutions (both crawling and rolling) that are robust against structural failures and can be adapted to a wide range of energy and actuation constraints. These successful controls will form the basis for building high-performance tensegrity robots in the near future.

In search of causality: a systematic review of the relationship between the built environment and physical activity among adults

PubMed Central

2011-01-01

Background Empirical evidence suggests that an association between the built environment and physical activity exists. This evidence is mostly derived from cross-sectional studies that do not account for other causal explanations such as neighborhood self-selection. Experimental and quasi-experimental designs can be used to isolate the effect of the built environment on physical activity, but in their absence, statistical techniques that adjust for neighborhood self-selection can be used with cross-sectional data. Previous reviews examining the built environment-physical activity relationship have not differentiated among findings based on study design. To deal with self-selection, we synthesized evidence regarding the relationship between objective measures of the built environment and physical activity by including in our review: 1) cross-sectional studies that adjust for neighborhood self-selection and 2) quasi-experiments. Method In September 2010, we searched for English-language studies on built environments and physical activity from all available years in health, leisure, transportation, social sciences, and geographical databases. Twenty cross-sectional and 13 quasi-experimental studies published between 1996 and 2010 were included in the review. Results Most associations between the built environment and physical activity were in the expected direction or null. Land use mix, connectivity and population density and overall neighborhood design were however, important determinants of physical activity. The built environment was more likely to be associated with transportation walking compared with other types of physical activity including recreational walking. Three studies found an attenuation in associations between built environment characteristics and physical activity after accounting for neighborhood self-selection. Conclusion More quasi-experiments that examine a broader range of environmental attributes in relation to context-specific physical activity and that measure changes in the built environment, neighborhood preferences and their effect on physical activity are needed. PMID:22077952

SuperB Progress Report for Accelerator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biagini, M.E.; Boni, R.; Boscolo, M.

2012-02-14

This report details the progress made in by the SuperB Project in the area of the Collider since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008. With this document we propose a new electron positron colliding beam accelerator to be built in Italy to study flavor physics in the B-meson system at an energy of 10 GeV in the center-of-mass. This facility is called a high luminosity B-factory with a project name 'SuperB'. This project builds on a long history of successful e+e- colliders built around themore » world, as illustrated in Figure 1.1. The key advances in the design of this accelerator come from recent successes at the DAFNE collider at INFN in Frascati, Italy, at PEP-II at SLAC in California, USA, and at KEKB at KEK in Tsukuba Japan, and from new concepts in beam manipulation at the interaction region (IP) called 'crab waist'. This new collider comprises of two colliding beam rings, one at 4.2 GeV and one at 6.7 GeV, a common interaction region, a new injection system at full beam energies, and one of the two beams longitudinally polarized at the IP. Most of the new accelerator techniques needed for this collider have been achieved at other recently completed accelerators including the new PETRA-3 light source at DESY in Hamburg (Germany) and the upgraded DAFNE collider at the INFN laboratory at Frascati (Italy), or during design studies of CLIC or the International Linear Collider (ILC). The project is to be designed and constructed by a worldwide collaboration of accelerator and engineering staff along with ties to industry. To save significant construction costs, many components from the PEP-II collider at SLAC will be recycled and used in this new accelerator. The interaction region will be designed in collaboration with the particle physics detector to guarantee successful mutual use. The accelerator collaboration will consist of several groups at present universities and national laboratories. In Italy these may include INFN Frascati and the University of Pisa, in the United States SLAC, LBNL, BNL and several universities, in France IN2P3, LAPP, and Grenoble, in Russia BINP, in Poland Krakow University, and in the UK the Cockcroft Institute. The construction time for this collider is a total of about four years. The new tunnel can be bored in about a year. The new accelerator components can be built and installed in about 4 years. The shipping of components from PEP-II at SLAC to Italy will take about a year. A new linac and damping ring complex for the injector for the rings can be built in about three years. The commissioning of this new accelerator will take about a year including the new electron and positron sources, new linac, new damping ring, new beam transport lines, two new collider rings and the Interaction Region. The new particle physics detector can be commissioned simultaneously with the accelerator. Once beam collisions start for particle physics, the luminosity will increase with time, likely reaching full design specifications after about two to three years of operation. After construction, the operation of the collider will be the responsibility of the Italian INFN governmental agency. The intent is to run this accelerator about ten months each year with about one month for accelerator turn-on and nine months for colliding beams. The collider will need to operate for about 10 years to provide the required 50 ab{sup -1} requested by the detector collaboration. Both beams as anticipated in this collider will have properties that are excellent for use as sources for synchrotron radiation (SR). The expected photon properties are comparable to those of PETRA-3 or NSLS-II. The beam lines and user facilities needed to carry out this SR program are being investigated.« less

Development of Reliable Life Support Systems

NASA Technical Reports Server (NTRS)

Carter, Layne

2017-01-01

The life support systems on the International Space Station (ISS) are the culmination of an extensive effort encompassing development, design, and test to provide the highest possible confidence in their operation on ISS. Many years of development testing are initially performed to identify the optimum technology and the optimum operational approach. The success of this development program depends on the accuracy of the system interfaces. The critical interfaces include the specific operational environment, the composition of the waste stream to be processed and the quality of the product. Once the development program is complete, a detailed system schematic is built based on the specific design requirements, followed by component procurement, assembly, and acceptance testing. A successful acceptance test again depends on accurately simulating the anticipated environment on ISS. The ISS Water Recovery System (WRS) provides an excellent example of where this process worked, as well as lessons learned that can be applied to the success of future missions. More importantly, ISS has provided a test bed to identify these design issues. Mechanical design issues have included an unreliable harmonic drive train in the Urine Processor's fluids pump, and seals in the Water Processor's Catalytic Reactor with insufficient life at the operational temperature. Systems issues have included elevated calcium in crew urine (due to microgravity effect) that resulted in precipitation at the desired water recovery rate, and the presence of an organosilicon compound (dimethylsilanediol) in the condensate that is not well removed by the water treatment process. Modifications to the WRS to address these issues are either complete (and now being evaluated on ISS) or are currently in work to insure the WRS has the required reliability before embarking on a mission to Mars.

CCG Programs with Clinical Data will Build on the Success of TCGA

Cancer.gov

Though TCGA will wrap up in 2016 with a concluding symposium, cancer genomics projects built upon the success of TCGA will continue to play a major part in the NCI’s mission to better understand and treat cancer in the years to come.

School Libraries and Innovation

ERIC Educational Resources Information Center

McGrath, Kevin G.

2015-01-01

School library programs have measured success by improved test scores. But how do next-generation school libraries demonstrate success as they strive to be centers of innovation and creativity? These libraries offer solutions for school leaders who struggle to restructure existing systems built around traditional silos of learning (subjects and…

Towards Requirements in Systems Engineering for Aerospace IVHM Design

NASA Technical Reports Server (NTRS)

Saxena, Abhinav; Roychoudhury, Indranil; Lin, Wei; Goebel, Kai

2013-01-01

Health management (HM) technologies have been employed for safety critical system for decades, but a coherent systematic process to integrate HM into the system design is not yet clear. Consequently, in most cases, health management resorts to be an after-thought or 'band-aid' solution. Moreover, limited guidance exists for carrying out systems engineering (SE) on the subject of writing requirements for designs with integrated vehicle health management (IVHM). It is well accepted that requirements are key to developing a successful IVHM system right from the concept stage to development, verification, utilization, and support. However, writing requirements for systems with IVHM capability have unique challenges that require the designers to look beyond their own domains and consider the constraints and specifications of other interlinked systems. In this paper we look at various stages in the SE process and identify activities specific to IVHM design and development. More importantly, several relevant questions are posed that system engineers must address at various design and development stages. Addressing these questions should provide some guidance to systems engineers towards writing IVHM related requirements to ensure that appropriate IVHM functions are built into the system design.

Built Environment Education in Art Education.

ERIC Educational Resources Information Center

Guilfoil, Joanne K., Ed.; Sandler, Alan R., Ed.

This anthology brings the study of the built environment, its design, social and cultural functions, and the criticism thereof into focus. Following a preface and introduction, 22 essays are organized in three parts. Part 1 includes: (1) "Landscape Art and the Role of the Natural Environment in Built Environment Education" (Heather…

Announcement: Community Preventive Services Task Force Recommendation for Built Environment Interventions to Increase Physical Activity.

PubMed

2017-05-05

The Community Preventive Services Task Force recently posted new information on its website: "Physical Activity: Built Environment Approaches Combining Transportation System Interventions with Land Use and Environmental Design." This information is available at https://www.thecommunityguide.org/findings/physical-activity-built-environment-approaches.

Cryogenic filter wheel design for an infrared instrument

NASA Astrophysics Data System (ADS)

Azcue, Joaquín.; Villanueva, Carlos; Sánchez, Antonio; Polo, Cristina; Reina, Manuel; Carretero, Angel; Torres, Josefina; Ramos, Gonzalo; Gonzalez, Luis M.; Sabau, Maria D.; Najarro, Francisco; Pintado, Jesús M.

2014-09-01

In the last two decades, Spain has built up a strong IR community which has successfully contributed to space instruments, reaching Co-PI level in the SPICA mission (Space Infrared Telescope for Cosmology and Astrophysics). Under the SPICA mission, INTA, focused on the SAFARI instrument requirements but highly adaptable to other missions has designed a cryogenic low dissipation filter wheel with six positions, taking as starting point the past experience of the team with the OSIRIS instrument (ROSETTA mission) filter wheels and adapting the design to work at cryogenic temperatures. One of the main goals of the mechanism is to use as much as possible commercial components and test them at cryogenic temperature. This paper is focused on the design of the filter wheel, including the material selection for each of the main components of the mechanism, the design of elastic mount for the filter assembly, a positioner device designed to provide positional accuracy and repeatability to the filter, allowing the locking of the position without dissipation. In order to know the position of the wheel on every moment a position sensor based on a Hall sensor was developed. A series of cryogenic tests have been performed in order to validate the material configuration selected, the ball bearing lubrication and the selection of the motor. A stepper motor characterization campaign was performed including heat dissipation measurements. The result is a six position filter wheel highly adaptable to different configurations and motors using commercial components. The mechanism was successfully tested at INTA facilities at 20K at breadboard level.

Development of proton computed tomography detectors for applications in hadron therapy

NASA Astrophysics Data System (ADS)

Bashkirov, Vladimir A.; Johnson, Robert P.; Sadrozinski, Hartmut F.-W.; Schulte, Reinhard W.

2016-02-01

Radiation therapy with protons and heavier ions is an attractive form of cancer treatment that could enhance local control and survival of cancers that are currently difficult to cure and lead to less side effects due to sparing of normal tissues. However, particle therapy faces a significant technical challenge because one cannot accurately predict the particle range in the patient using data provided by existing imaging technologies. Proton computed tomography (pCT) is an emerging imaging modality capable of improving the accuracy of range prediction. In this paper, we describe the successive pCT scanners designed and built by our group with the goal to support particle therapy treatment planning and image guidance by reconstructing an accurate 3D map of the stopping power relative to water in patient tissues. The pCT scanners we have built to date consist of silicon telescopes, which track the proton before and after the object to be reconstructed, and an energy or range detector, which measures the residual energy and/or range of the protons used to evaluate the water equivalent path length (WEPL) of each proton in the object. An overview of a decade-long evolution of the conceptual design of pCT scanners and their calibration is given. Results of scanner performance tests are presented, which demonstrate that the latest pCT scanner approaches readiness for clinical applications in hadron therapy.

Design, Fabrication and Testing of an Axisymmetric, Annular, Subsonic Diffuser and Associated Instrumentation Systems

DTIC Science & Technology

1981-12-01

this investigation are threefold. First, an annular diffuser is to be designed and built to model the annulardiffuser arranged between the compressor ...on these calculations. The final design of the diffuser model (Figs 7, 8, 12 1and 9) was 20 in in diameter at the inlet. The axial annular sections...traversing mechanism was designed and built (Fig 18). It was constructed so that all peripheral data stations at one axial point could be used either

SeaWiFS Postlaunch Technical Report Series. Volume 1; The SeaWiFS Transfer Radiometer (SXR)

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); Johnson, B. Carol; Cromer, Christopher L.

1998-01-01

The SeaWiFS Transfer Radiometer (SXR) was built for the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project as part of an Interagency Agreement with the National Aeronautics and Space Administration (NASA). The SXR is a multichannel radiometer designed to verify and compare measurements of spectral radiance at six discrete wavelengths in the visible and near infrared for various calibration sources in the SeaWiFS Project. In addition, the SXR is used to compare these sources to standards of spectral radiance maintained at the National Institute of Standards and Technology (NIST). The SXR was designed, built, and thoroughly characterized in the Optical Technology Division at NIST. A unique optical design provides six independent optical paths, each equipped with a temperature stabilized interference filter and silicon photodiode. A separate beam path through the input lens is used to visually align the SXR. The entrance windows for each channel overlap at the source, with each channel sampling a unique solid angle within the field of view of the SXR; this allows for simultaneous sampling of all channels. The combined standard relative uncertainty of spectral radiance measurements with the SXR is estimated to be between 0.6% and 1.3%. This report describes the design and construction of the SXR in detail, and gives the results of the optical characterization and calibrations done at NIST. The SXR has been used for several intercomparisons which include several SeaWiFS Intercalibration Round-Robin Experiments (SIRREXs); those done at the Marine Optical Buoy (MOBY) laboratories in Honolulu, Hawaii; at the NEC Corporation in Yokohama, Japan; and Orbital Sciences Corporation (OSC) in Germantown, Maryland. Thorough optical characterization and calibration of the SXR was essential to the successful application of the radiometer for these measurements.

Study of Internal Channel Surface Roughnesses Manufactured by Selective Laser Melting in Aluminum and Titanium Alloys

NASA Astrophysics Data System (ADS)

Pakkanen, Jukka; Calignano, Flaviana; Trevisan, Francesco; Lorusso, Massimo; Ambrosio, Elisa Paola; Manfredi, Diego; Fino, Paolo

2016-08-01

Interest in additive manufacturing (AM) has gained considerable impetus over the past decade. One of the driving factors for AM success is the ability to create unique designs with intrinsic characteristics as, e.g., internal channels used for hydraulic components, cooling channels, and heat exchangers. However, a couple of the main problems in internal channels manufactured by AM technologies are the high surface roughness obtained and the distortion of the channel shape. There is still much to understand in these design aspects. In this study, a cylindrical geometry for internal channels to be built with different angles with respect to the building plane in AlSi10Mg and Ti6Al4V alloys by selective laser melting was considered. The internal surfaces of the channels produced in both materials were analyzed by means of a surface roughness tester and by optical and electron microscopy to evaluate the effects of the material and design choices.

Design and fabrication of prototype 6×6 cm 2 microchannel plate photodetector with bialkali photocathode for fast timing applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Junqi; Byrum, Karen; Demarteau, Marcel

Planar microchannel plate-based photodetector with bialkali photocathode is capable of fast and accurate time and position resolutions. A new 6 cm x 6 cm photodetector production facility was designed and built at Argonne National Laboratory. Small form-factor MCP-based photodetectors completely constructed of glass were designed and prototypes were successfully fabricated. Knudsen effusion cells were incorporated in the photocathode growth chamber to achieve uniform and high quantum efficiency hotocathodes. The thin film uniformity distribution was simulated and measured for an antimony film deposition, showing uniformity of better than 10%. Several prototype devices with bialkali photocathodes have been fabricated with the describedmore » system and their characteristics were evaluated in the large signal (multi-PE) limit. A typical prototype device exhibits time-of-flight resolution of ~ 27 psec and differential time resolution of ~ 9 psec, corresponding to spatial resolution of ~ 0.65 mm.« less

A mobile phone user interface for image-based dietary assessment

NASA Astrophysics Data System (ADS)

Ahmad, Ziad; Khanna, Nitin; Kerr, Deborah A.; Boushey, Carol J.; Delp, Edward J.

2014-02-01

Many chronic diseases, including obesity and cancer, are related to diet. Such diseases may be prevented and/or successfully treated by accurately monitoring and assessing food and beverage intakes. Existing dietary assessment methods such as the 24-hour dietary recall and the food frequency questionnaire, are burdensome and not generally accurate. In this paper, we present a user interface for a mobile telephone food record that relies on taking images, using the built-in camera, as the primary method of recording. We describe the design and implementation of this user interface while stressing the solutions we devised to meet the requirements imposed by the image analysis process, yet keeping the user interface easy to use.

Fabrication and assembly of a superconducting undulator for the advanced photon source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasse, Quentin; Fuerst, J. D.; Ivanyushenkov, Y.

2014-01-29

A prototype superconducting undulator magnet (SCU0) has been built at the Advanced Photon Source (APS) of Argonne National Laboratory (ANL) and has successfully completed both cryogenic performance and magnetic measurement test programs. The SCU0 closed loop, zero-boil-off cryogenic system incorporates high temperature superconducting (HTS) current leads, cryocoolers, a LHe reservoir supplying dual magnetic cores, and an integrated cooled beam chamber. This system presented numerous challenges in the design, fabrication, and assembly of the device. Aspects of this R and D relating to both the cryogenic and overall assembly of the device are presented here. The SCU0 magnet has been installedmore » in the APS storage ring.« less

Authentic teaching and learning through synthetic biology

PubMed Central

Kuldell, Natalie

2007-01-01

Synthetic biology is an emerging engineering discipline that, if successful, will allow well-characterized biological components to be predictably and reliably built into robust organisms that achieve specific functions. Fledgling efforts to design and implement a synthetic biology curriculum for undergraduate students have shown that the co-development of this emerging discipline and its future practitioners does not undermine learning. Rather it can serve as the lynchpin of a synthetic biology curriculum. Here I describe educational goals uniquely served by synthetic biology teaching, detail ongoing curricula development efforts at MIT, and specify particular aspects of the emerging field that must develop rapidly in order to best train the next generation of synthetic biologists. PMID:18271945

A photoelectric amplifier as a dye detector

USGS Publications Warehouse

Ebel, Wesley J.

1962-01-01

A dye detector, based on a modified photoelectric amplifier, has been planned, built, and tested. It was designed to record automatically the time of arrival of fluorescein dye at predetermined points in a stream system. Laboratory tests and stream trials proved the instrument to be efficient. Small changes in color can be detected in turbid or clear water. The unit has been used successfully for timing intervals of more than 17 hours; significant savings of time and manpower have resulted. Replacement of the clock, included in the original device, with a recording milliammeter increases the efficiency of the unit by contin,!ously recording changes in turbidity. The addition of this component would increase the cost from $75 to approximately $105.

Photographic film image enhancement

NASA Technical Reports Server (NTRS)

Horner, J. L.

1975-01-01

A series of experiments were undertaken to assess the feasibility of defogging color film by the techniques of optical spatial filtering. A coherent optical processor was built using red, blue, and green laser light input and specially designed Fourier transformation lenses. An array of spatial filters was fabricated on black and white emulsion slides using the coherent optical processor. The technique was first applied to laboratory white light fogged film, and the results were successful. However, when the same technique was applied to some original Apollo X radiation fogged color negatives, the results showed no similar restoration. Examples of each experiment are presented and possible reasons for the lack of restoration in the Apollo films are discussed.

P80 SRM low torque flex-seal development - thermal and chemical modeling of molding process

NASA Astrophysics Data System (ADS)

Descamps, C.; Gautronneau, E.; Rousseau, G.; Daurat, M.

2009-09-01

The development of the flex-seal component of the P80 nozzle gave the opportunity to set up new design and manufacturing process methods. Due to the short development lead time required by VEGA program, the usual manufacturing iterative tests work flow, which is usually time consuming, had to be enhanced in order to use a more predictive approach. A newly refined rubber vulcanization description was built up and identified on laboratory samples. This chemical model was implemented in a thermal analysis code. The complete model successfully supports the manufacturing processes. These activities were conducted with the support of ESA/CNES Research & Technologies and DGA (General Delegation for Armament).

A Mobile Phone User Interface for Image-Based Dietary Assessment

PubMed Central

Ahmad, Ziad; Khanna, Nitin; Kerr, Deborah A.; Boushey, Carol J.; Delp, Edward J.

2016-01-01

Many chronic diseases, including obesity and cancer, are related to diet. Such diseases may be prevented and/or successfully treated by accurately monitoring and assessing food and beverage intakes. Existing dietary assessment methods such as the 24-hour dietary recall and the food frequency questionnaire, are burdensome and not generally accurate. In this paper, we present a user interface for a mobile telephone food record that relies on taking images, using the built-in camera, as the primary method of recording. We describe the design and implementation of this user interface while stressing the solutions we devised to meet the requirements imposed by the image analysis process, yet keeping the user interface easy to use. PMID:28572696

A Mobile Phone User Interface for Image-Based Dietary Assessment.

PubMed

Ahmad, Ziad; Khanna, Nitin; Kerr, Deborah A; Boushey, Carol J; Delp, Edward J

2014-02-02

Many chronic diseases, including obesity and cancer, are related to diet. Such diseases may be prevented and/or successfully treated by accurately monitoring and assessing food and beverage intakes. Existing dietary assessment methods such as the 24-hour dietary recall and the food frequency questionnaire, are burdensome and not generally accurate. In this paper, we present a user interface for a mobile telephone food record that relies on taking images, using the built-in camera, as the primary method of recording. We describe the design and implementation of this user interface while stressing the solutions we devised to meet the requirements imposed by the image analysis process, yet keeping the user interface easy to use.

A description of the ABCD organizational structure and communication framework.

PubMed

Auchter, Allison M; Hernandez Mejia, Margie; Heyser, Charles J; Shilling, Paul D; Jernigan, Terry L; Brown, Sandra A; Tapert, Susan F; Dowling, Gayathri J

2018-04-16

The Adolescent Brain Cognitive Development (ABCD) study is designed to be the largest study of brain development and child health in the United States, performing comprehensive assessments of 11,500 children repeatedly for 10 years. An endeavor of this magnitude requires an organized framework of governance and communication that promotes collaborative decision-making and dissemination of information. The ABCD consortium structure, built upon the Matrix Management approach of organizational theory, facilitates the integration of input from all institutions, numerous internal workgroups and committees, federal partners, and external advisory groups to make use of a broad range of expertise to ensure the study's success. Copyright © 2018 Elsevier Ltd. All rights reserved.

Shape design sensitivity analysis using domain information

NASA Technical Reports Server (NTRS)

Seong, Hwal-Gyeong; Choi, Kyung K.

1985-01-01

A numerical method for obtaining accurate shape design sensitivity information for built-up structures is developed and demonstrated through analysis of examples. The basic character of the finite element method, which gives more accurate domain information than boundary information, is utilized for shape design sensitivity improvement. A domain approach for shape design sensitivity analysis of built-up structures is derived using the material derivative idea of structural mechanics and the adjoint variable method of design sensitivity analysis. Velocity elements and B-spline curves are introduced to alleviate difficulties in generating domain velocity fields. The regularity requirements of the design velocity field are studied.

Increasing Success Rates in Developmental Math: The Complementary Role of Individual and Institutional Characteristics

ERIC Educational Resources Information Center

Fong, Kristen E.; Melguizo, Tatiana; Prather, George

2015-01-01

This study tracks students' progression through developmental math sequences and defines progression as both attempting and passing each level of the sequence. A model of successful progression in developmental education was built utilizing individual-, institutional-, and developmental math-level factors. Employing step-wise logistic regression…

Success Is in the Details: Publishing To Validate Elementary Authors.

ERIC Educational Resources Information Center

Chihak, Judy

1999-01-01

Describes Panther Paw Press, a school-based publishing program that is built on the efforts of teachers, parents, students, and a succession of supportive school principals. Discusses the details that make this publishing program work framed in the six goals articulated in the Panther Paw Press Handbook. (SR)

The Atacama Large Millimeter/Submillimeter Array (ALMA) - A Successful Three-Way International Partnership Without a Majority Stakeholder

NASA Astrophysics Data System (ADS)

Vanden Bout, Paul A.

2013-04-01

The Atacama Millimeter/Submillimeter Array (ALMA) is the largest ground-based astronomical facility built to date. It's size and challenging site required an international effort. This talk presents the partnership structure, management challenges, current status, and examples of early scientific successes.

Self, Society, and the "New Gerontology"

ERIC Educational Resources Information Center

Holstein, Martha B.; Minkler, Meredith

2003-01-01

The "new gerontology," built on the concept of successful aging, sets forth the preconditions for and the end product of the process of aging successfully. Focused on health and active participation in life, it vests largely within individuals the power to achieve this normatively desirable state. While acknowledging the contributions of the…

Community Literacy at Work with STRIDE (Success Through Reading Improvement and DEvelopment): Overview of a Successful Community Literacy Program.

ERIC Educational Resources Information Center

Macy, Rita

STRIDE (Success Through Reading Improvement and DEvelopment) is a literacy program developed in 1986 by Crowder College, located in the rural Ozarks of southwestern Missouri. Serving all age groups with trained literacy tutors ranging in age from 11 to over 60, STRIDE has been built on five main activities: (1) develop a philosophy that is…

Using Modern Design Tools for Digital Avionics Development

NASA Technical Reports Server (NTRS)

Hyde, David W.; Lakin, David R., II; Asquith, Thomas E.

2000-01-01

Using Modem Design Tools for Digital Avionics Development Shrinking development time and increased complexity of new avionics forces the designer to use modem tools and methods during hardware development. Engineers at the Marshall Space Flight Center have successfully upgraded their design flow and used it to develop a Mongoose V based radiation tolerant processor board for the International Space Station's Water Recovery System. The design flow, based on hardware description languages, simulation, synthesis, hardware models, and full functional software model libraries, allowed designers to fully simulate the processor board from reset, through initialization before any boards were built. The fidelity of a digital simulation is limited to the accuracy of the models used and how realistically the designer drives the circuit's inputs during simulation. By using the actual silicon during simulation, device modeling errors are reduced. Numerous design flaws were discovered early in the design phase when they could be easily fixed. The use of hardware models and actual MIPS software loaded into full functional memory models also provided checkout of the software development environment. This paper will describe the design flow used to develop the processor board and give examples of errors that were found using the tools. An overview of the processor board firmware will also be covered.

46 CFR 108.515 - Requirements for units built before October 1, 1996.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Requirements for units built before October 1, 1996. 108.515 Section 108.515 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.515 Requirements for units built...

46 CFR 108.515 - Requirements for units built before October 1, 1996.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Requirements for units built before October 1, 1996. 108.515 Section 108.515 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.515 Requirements for units built...

46 CFR 108.515 - Requirements for units built before October 1, 1996.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Requirements for units built before October 1, 1996. 108.515 Section 108.515 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.515 Requirements for units built...

46 CFR 108.515 - Requirements for units built before October 1, 1996.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Requirements for units built before October 1, 1996. 108.515 Section 108.515 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.515 Requirements for units built...

ORION: A Supersynchronous Transfer Orbit mission

NASA Astrophysics Data System (ADS)

Walters, I. M.; Baker, J. F.; Shurmer, I. M.

1995-05-01

ORION F1 was launched on 29th November 1994 on an Atlas IIA launch vehicle. It was designed, built and delivered in-orbit by Matra Marconi Space Systems Plc and was handed over to ORION Satellite Corporation on 20th January 1995 at its on-station longitude of 37.5 deg W. The mission differed significantly from that of any other geostationary communications satellite in that the Transfer Orbit apogee altitude of 123,507 km was over three times geosynchronous (GEO) altitude and one third of the way to the moon. The SuperSynchronous Transfer Orbit (SSTO) mission is significantly different from the standard Geostationary Transfer Orbit (GTO)mission in a number of ways. This paper discusses the essential features of the mission design through its evolution since 1987 and the details of the highly successful mission itself including a detailed account of the attitude determination achieved using the Galileo Earth and Sun Sensor (ESS).

Development and fabrication of patient-specific knee implant using additive manufacturing techniques

NASA Astrophysics Data System (ADS)

Zammit, Robert; Rochman, Arif

2017-10-01

Total knee replacement is the most effective treatment to relief pain and restore normal function in a diseased knee joint. The aim of this research was to develop a patient-specific knee implant which can be fabricated using additive manufacturing techniques and has reduced wear rates using a highly wear resistant materials. The proposed design was chosen based on implant requirements, such as reduction in wear rates as well as strong fixation. The patient-specific knee implant improves on conventional knee implants by modifying the articulating surfaces and bone-implant interfaces. Moreover, tribological tests of different polymeric wear couples were carried out to determine the optimal materials to use for the articulating surfaces. Finite element analysis was utilized to evaluate the stresses sustained by the proposed design. Finally, the patient-specific knee implant was successfully built using additive manufacturing techniques.

ORION: A Supersynchronous Transfer Orbit mission

NASA Technical Reports Server (NTRS)

Walters, I. M.; Baker, J. F.; Shurmer, I. M.

1995-01-01

ORION F1 was launched on 29th November 1994 on an Atlas IIA launch vehicle. It was designed, built and delivered in-orbit by Matra Marconi Space Systems Plc and was handed over to ORION Satellite Corporation on 20th January 1995 at its on-station longitude of 37.5 deg W. The mission differed significantly from that of any other geostationary communications satellite in that the Transfer Orbit apogee altitude of 123,507 km was over three times geosynchronous (GEO) altitude and one third of the way to the moon. The SuperSynchronous Transfer Orbit (SSTO) mission is significantly different from the standard Geostationary Transfer Orbit (GTO)mission in a number of ways. This paper discusses the essential features of the mission design through its evolution since 1987 and the details of the highly successful mission itself including a detailed account of the attitude determination achieved using the Galileo Earth and Sun Sensor (ESS).

Database Are Not Toasters: A Framework for Comparing Data Warehouse Appliances

NASA Astrophysics Data System (ADS)

Trajman, Omer; Crolotte, Alain; Steinhoff, David; Nambiar, Raghunath Othayoth; Poess, Meikel

The success of Business Intelligence (BI) applications depends on two factors, the ability to analyze data ever more quickly and the ability to handle ever increasing volumes of data. Data Warehouse (DW) and Data Mart (DM) installations that support BI applications have historically been built using traditional architectures either designed from the ground up or based on customized reference system designs. The advent of Data Warehouse Appliances (DA) brings packaged software and hardware solutions that address performance and scalability requirements for certain market segments. The differences between DAs and custom installations make direct comparisons between them impractical and suggest the need for a targeted DA benchmark. In this paper we review data warehouse appliances by surveying thirteen products offered today. We assess the common characteristics among them and propose a classification for DA offerings. We hope our results will help define a useful benchmark for DAs.

Testing of Twin Linear Aerospike XRS-2200 Engine

NASA Technical Reports Server (NTRS)

2001-01-01

The test of twin Linear Aerospike XRS-2200 engines, originally built for the X-33 program, was performed on August 6, 2001 at NASA's Sternis Space Center, Mississippi. The engines were fired for the planned 90 seconds and reached a planned maximum power of 85 percent. NASA's Second Generation Reusable Launch Vehicle Program , also known as the Space Launch Initiative (SLI), is making advances in propulsion technology with this third and final successful engine hot fire, designed to test electro-mechanical actuators. Information learned from this hot fire test series about new electro-mechanical actuator technology, which controls the flow of propellants in rocket engines, could provide key advancements for the propulsion systems for future spacecraft. The Second Generation Reusable Launch Vehicle Program, led by NASA's Marshall Space Flight Center in Huntsville, Alabama, is a technology development program designed to increase safety and reliability while reducing costs for space travel. The X-33 program was cancelled in March 2001.

KSC-2010-4698

NASA Image and Video Library

2010-09-20

CAPE CANAVERAL, Fla. - Workers of Superior Solar LLC in Longwood, Fla., begin to install more than 300 solar panels on the roof of the Propellants North Administrative and Maintenance Facility at NASA's Kennedy Space Center in Florida. Each panel, built in Sharp Corp.'s Memphis, Tenn., plant, will produce 235 watts of clean energy. The green facility in Kennedy's Launch Complex 39 area will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to a single-story shop to store cryogenic fuel transfer equipment. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) Platinum certification. If successful, it will be the first NASA facility to achieve this highest of LEED ratings after it is completed. The facility was designed for NASA by Jones Edmunds and Associates. H. W. Davis Construction is the construction contractor. Photo credit: NASA/Jim Grossmann

KSC-2010-4700

NASA Image and Video Library

2010-09-20

CAPE CANAVERAL, Fla. - Workers of Superior Solar LLC in Longwood, Fla., begin to install more than 300 solar panels on the roof of the Propellants North Administrative and Maintenance Facility at NASA's Kennedy Space Center in Florida. Each panel, built in Sharp Corp.'s Memphis, Tenn., plant, will produce 235 watts of clean energy. The green facility in Kennedy's Launch Complex 39 area will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to a single-story shop to store cryogenic fuel transfer equipment. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) Platinum certification. If successful, it will be the first NASA facility to achieve this highest of LEED ratings after it is completed. The facility was designed for NASA by Jones Edmunds and Associates. H. W. Davis Construction is the construction contractor. Photo credit: NASA/Jim Grossmann

KSC-2010-4699

NASA Image and Video Library

2010-09-20

CAPE CANAVERAL, Fla. - Workers of Superior Solar LLC in Longwood, Fla., prepare to install more than 300 solar panels on the roof of the Propellants North Administrative and Maintenance Facility at NASA's Kennedy Space Center in Florida. Each panel, built in Sharp Corp.'s Memphis, Tenn., plant, will produce 235 watts of clean energy. The green facility in Kennedy's Launch Complex 39 area will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to a single-story shop to store cryogenic fuel transfer equipment. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) Platinum certification. If successful, it will be the first NASA facility to achieve this highest of LEED ratings after it is completed. The facility was designed for NASA by Jones Edmunds and Associates. H. W. Davis Construction is the construction contractor. Photo credit: NASA/Jim Grossmann

KSC-2010-4697

NASA Image and Video Library

2010-09-20

CAPE CANAVERAL, Fla. - Workers of Superior Solar LLC in Longwood, Fla., begin to install more than 300 solar panels on the roof of the Propellants North Administrative and Maintenance Facility at NASA's Kennedy Space Center in Florida. Each panel, built in Sharp Corp.'s Memphis, Tenn., plant, will produce 235 watts of clean energy. The green facility in Kennedy's Launch Complex 39 area will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to a single-story shop to store cryogenic fuel transfer equipment. The facility is striving to qualify for the U.S. Green Building Council’s Leadership in Energy and Environmental Design (LEED) Platinum certification. If successful, it will be the first NASA facility to achieve this highest of LEED ratings after it is completed. The facility was designed for NASA by Jones Edmunds and Associates. H. W. Davis Construction is the construction contractor. Photo credit: NASA/Jim Grossmann

Research Technology

NASA Image and Video Library

2001-08-06

The test of twin Linear Aerospike XRS-2200 engines, originally built for the X-33 program, was performed on August 6, 2001 at NASA's Sternis Space Center, Mississippi. The engines were fired for the planned 90 seconds and reached a planned maximum power of 85 percent. NASA's Second Generation Reusable Launch Vehicle Program , also known as the Space Launch Initiative (SLI), is making advances in propulsion technology with this third and final successful engine hot fire, designed to test electro-mechanical actuators. Information learned from this hot fire test series about new electro-mechanical actuator technology, which controls the flow of propellants in rocket engines, could provide key advancements for the propulsion systems for future spacecraft. The Second Generation Reusable Launch Vehicle Program, led by NASA's Marshall Space Flight Center in Huntsville, Alabama, is a technology development program designed to increase safety and reliability while reducing costs for space travel. The X-33 program was cancelled in March 2001.

Russian Rocket Engine Test

NASA Technical Reports Server (NTRS)

1998-01-01

NASA engineers successfully tested a Russian-built rocket engine on November 4, 1998 at the Marshall Space Flight Center (MSFC) Advanced Engine Test Facility, which had been used for testing the Saturn V F-1 engines and Space Shuttle Main engines. The MSFC was under a Space Act Agreement with Lockheed Martin Astronautics of Denver to provide a series of test firings of the Atlas III propulsion system configured with the Russian-designed RD-180 engine. The tests were designed to measure the performance of the Atlas III propulsion system, which included avionics and propellant tanks and lines, and how these components interacted with the RD-180 engine. The RD-180 is powered by kerosene and liquid oxygen, the same fuel mix used in Saturn rockets. The RD-180, the most powerful rocket engine tested at the MSFC since Saturn rocket tests in the 1960s, generated 860,000 pounds of thrust.

Around Marshall

NASA Image and Video Library

1998-11-04

NASA engineers successfully tested a Russian-built rocket engine on November 4, 1998 at the Marshall Space Flight Center (MSFC) Advanced Engine Test Facility, which had been used for testing the Saturn V F-1 engines and Space Shuttle Main engines. The MSFC was under a Space Act Agreement with Lockheed Martin Astronautics of Denver to provide a series of test firings of the Atlas III propulsion system configured with the Russian-designed RD-180 engine. The tests were designed to measure the performance of the Atlas III propulsion system, which included avionics and propellant tanks and lines, and how these components interacted with the RD-180 engine. The RD-180 is powered by kerosene and liquid oxygen, the same fuel mix used in Saturn rockets. The RD-180, the most powerful rocket engine tested at the MSFC since Saturn rocket tests in the 1960s, generated 860,000 pounds of thrust.

Halbach array motor/generators: A novel generalized electric machine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merritt, B.T.; Post, R.F.; Dreifuerst, G.R.

1995-02-01

For many years Klaus Halbach has been investigating novel designs for permanent magnet arrays, using advanced analytical approaches and employing a keen insight into such systems. One of his motivations for this research was to find more efficient means for the utilization of permanent magnets for use in particle accelerators and in the control of particle beams. As a result of his pioneering work, high power free-electron laser systems, such as the ones built at the Lawrence Livermore Laboratory, became feasible, and his arrays have been incorporated into other particle-focusing systems of various types. This paper reports another, quite different,more » application of Klaus` work, in the design of high power, high efficiency, electric generators and motors. When tested, these motor/generator systems display some rather remarkable properties. Their success derives from the special properties which these arrays, which the authors choose to call {open_quotes}Halbach arrays,{close_quotes} possess.« less

Monitoring space shuttle air quality using the Jet Propulsion Laboratory electronic nose

NASA Technical Reports Server (NTRS)

Ryan, Margaret Amy; Zhou, Hanying; Buehler, Martin G.; Manatt, Kenneth S.; Mowrey, Victoria S.; Jackson, Shannon P.; Kisor, Adam K.; Shevade, Abhijit V.; Homer, Margie L.

2004-01-01

A miniature electronic nose (ENose) has been designed and built at the Jet Propulsion Laboratory (JPL), Pasadena, CA, and was designed to detect, identify, and quantify ten common contaminants and relative humidity changes. The sensing array includes 32 sensing films made from polymer carbon-black composites. Event identification and quantification were done using the Levenberg-Marquart nonlinear least squares method. After successful ground training, this ENose was used in a demonstration experiment aboard STS-95 (October-November, 1998), in which the ENose was operated continuously for six days and recorded the sensors' response to the air in the mid-deck. Air samples were collected daily and analyzed independently after the flight. Changes in shuttle-cabin humidity were detected and quantified by the JPL ENose; neither the ENose nor the air samples detected any of the contaminants on the target list. The device is microgravity insensitive.

Bubble dynamics, two-phase flow, and boiling heat transfer in a microgravity environment

NASA Technical Reports Server (NTRS)

Chung, Jacob N.

1994-01-01

The two-phase bubbly flow and boiling heat transfer in microgravity represents a substantial challenge to scientists and engineers and yet there is an urgent need to seek fundamental understanding in this area for future spacecraft design and space missions. At Washington State University, we have successfully designed, built and tested a 2.1 second drop tower with an innovation airbag deceleration system. Microgravity boiling experiments performed in our 0.6 second Drop Tower produced data flow visualizations that agree with published results and also provide some new understanding concerning flow boiling and microgravity bubble behavior. On the analytical and numerical work, the edge effects of finite divergent electrode plates on the forces experienced by bubbles were investigated. Boiling in a concentric cylinder microgravity and an electric field was numerically predicted. We also completed a feasibility study for microgravity boiling in an acoustic field.

Designing with Care. A Guide to Adaptation of the Built Environment for Disabled Persons.

ERIC Educational Resources Information Center

Hanson, Lisa; And Others

Developed as part of the International Year of Disabled Persons, the guide is intended to help planners, architects, and designers to accommodate the built environment of developing regions for disabled persons. Guidelines focus on public building in urban or village settings and emphasize simple solutions to common problems. Following an…

Design and evaluation of potentiometric principles for bladder volume monitoring: a preliminary study.

PubMed

Chen, Shih-Ching; Hsieh, Tsung-Hsun; Fan, Wen-Jia; Lai, Chien-Hung; Chen, Chun-Lung; Wei, Wei-Feng; Peng, Chih-Wei

2015-06-01

Recent advances in microelectronics and wireless transmission technology have led to the development of various implantable sensors for real-time monitoring of bladder conditions. Although various sensing approaches for monitoring bladder conditions were reported, most such sensors have remained at the laboratory stage due to the existence of vital drawbacks. In the present study, we explored a new concept for monitoring the bladder capacity on the basis of potentiometric principles. A prototype of a potentiometer module was designed and fabricated and integrated with a commercial wireless transmission module and power unit. A series of in vitro pig bladder experiments was conducted to determine the best design parameters for implementing the prototype potentiometric device and to prove its feasibility. We successfully implemented the potentiometric module in a pig bladder model in vitro, and the error of the accuracy of bladder volume detection was <±3%. Although the proposed potentiometric device was built using a commercial wireless module, the design principles and animal experience gathered from this research can serve as a basis for developing new implantable bladder sensors in the future.

Design and implementation of an improved chilled water glycol system for NICI array electronics thermal enclosure

NASA Astrophysics Data System (ADS)

Gausachs, Gaston

2008-07-01

The Near Infrared Chronographic Imager (NICI) being commissioned at Gemini was upgraded with a more powerful Chilled Water Glycol System to address early overheating problems. The previous system was replaced with a completely new design favoring improved airflow and increased heat transfer capabilities. The research leading to this upgrade showed a significant lack of cooling power of the original design. The solution was a combination of commercial heat exchanger and fans and a custom built enclosure. As a prime infrared telescope facility, Gemini is very much interested in maintaining the least amount of heat dissipated to the ambient air. The results obtained through the implementation of this solution will be helpful in understanding the state of other existing electronics enclosures as well as those for new instruments to come. With the advent of electronic intensive AO systems, future electronics enclosures must take full advantage of improved cooling. This paper describes the design and implementation phases of the project. The results under maximum operating capacity proved to be within the expected theoretical values and were deemed successful.

Design of optimal impulse transfers from the Sun-Earth libration point to asteroid

NASA Astrophysics Data System (ADS)

Wang, Yamin; Qiao, Dong; Cui, Pingyuan

2015-07-01

The lunar probe, Chang'E-2, is the first one to successfully achieve both the transfer to Sun-Earth libration point orbit and the flyby of near-Earth asteroid Toutatis. This paper, taking the Chang'E-2's asteroid flyby mission as an example, provides a method to design low-energy transfers from the libration point orbit to an asteroid. The method includes the analysis of transfer families and the design of optimal impulse transfers. Firstly, the one-impulse transfers are constructed by correcting the initial guesses, which are obtained by perturbing in the direction of unstable eigenvector. Secondly, the optimality of one-impulse transfers is analyzed and the optimal impulse transfers are built by using the primer vector theory. After optimization, the transfer families, including the slow and the fast transfers, are refined to be continuous and lower-cost transfers. The method proposed in this paper can be also used for designing transfers from an arbitrary Sun-Earth libration point orbit to a near-Earth asteroid in the Sun-Earth-Moon system.

Full-Scale Wind-Tunnel Investigation of Wing-Cooling Ducts Effects of Propeller Slipstream, Special Report

NASA Technical Reports Server (NTRS)

Nickle, F. R.; Freeman, Arthur B.

1939-01-01

The safety of remotely operated vehicles depends on the correctness of the distributed protocol that facilitates the communication between the vehicle and the operator. A failure in this communication can result in catastrophic loss of the vehicle. To complicate matters, the communication system may be required to satisfy several, possibly conflicting, requirements. The design of protocols is typically an informal process based on successive iterations of a prototype implementation. Yet distributed protocols are notoriously difficult to get correct using such informal techniques. We present a formal specification of the design of a distributed protocol intended for use in a remotely operated vehicle, which is built from the composition of several simpler protocols. We demonstrate proof strategies that allow us to prove properties of each component protocol individually while ensuring that the property is preserved in the composition forming the entire system. Given that designs are likely to evolve as additional requirements emerge, we show how we have automated most of the repetitive proof steps to enable verification of rapidly changing designs.

Using Symmetry to Design Self-Assembling Protein Cages and Nanomaterials on the Mid-Nanometer Scale

NASA Astrophysics Data System (ADS)

Yeates, Todd

Self-assembling molecular structures having diverse cellular functions are widespread in nature. Some of the largest and most sophisticated types are built from many copies of the same or similar protein molecules arranged following principles of symmetry. A long-standing engineering goal has been to design novel protein molecules to self-assemble into geometrically specific structures similar to the extraordinary structures that have evolved in Nature. Practical routes to this goal have been developed by using ideas in symmetry to articulate the minimum design requirements for achieving various types of symmetric architectures, including cages, extended two-dimensional layers, and three-dimensional crystalline materials. The key requirement is that two distinct self-associating interfaces, each conferring one element of rotational symmetry, have to be engineered into the protein molecule (or molecules), following particular geometric specifications. The main principle is that combining two separate symmetry elements into a single molecular entity produces a molecule that necessarily assembles into an architecture dictated by a symmetry group that is the product of the two simpler contributing symmetries. Recent experiments have demonstrated success using a variety of symmetry-based strategies. Strategic variations are emerging that differ from each other with respect to biophysical features such as flexibility vs rigidity in the assembled structures, and with respect to design aspects such as whether the protein interfaces are inherited from natural oligomeric proteins or are designed de novo by advanced computational methods. The success of these strategies has been proven by determining crystal structures of several giant, self-assembling protein cages and clusters (10-25 nm in diameter), created by design. The ability to create sophisticated supramolecular structures from designed protein subunits opens the way to broad applications in synthetic biology and nanotechnology.

Built-in electric field thickness design for betavoltaic batteries

NASA Astrophysics Data System (ADS)

Haiyang, Chen; Darang, Li; Jianhua, Yin; Shengguo, Cai

2011-09-01

Isotope source energy deposition along the thickness direction of a semiconductor is calculated, based upon which an ideal short current is evaluated for betavoltaic batteries. Electron-hole pair recombination and drifting length in a PN junction built-in electric field are extracted by comparing the measured short currents with the ideal short currents. A built-in electric field thickness design principle is proposed for betavoltaic batteries: after measuring the energy deposition depth and the carrier drift length, the shorter one should then be chosen as the built-in electric field thickness. If the energy deposition depth is much larger than the carrier drift length, a multi-junction is preferred in betavoltaic batteries and the number of the junctions should be the value of the deposition depth divided by the drift length.

Transformers: Shape-Changing Space Systems Built with Robotic Textiles

NASA Technical Reports Server (NTRS)

Stoica, Adrian

2013-01-01

Prior approaches to transformer-like robots had only very limited success. They suffer from lack of reliability, ability to integrate large surfaces, and very modest change in overall shape. Robots can now be built from two-dimensional (2D) layers of robotic fabric. These transformers, a new kind of robotic space system, are dramatically different from current systems in at least two ways. First, the entire transformer is built from a single, thin sheet; a flexible layer of a robotic fabric (ro-fabric); or robotic textile (ro-textile). Second, the ro-textile layer is foldable to small volume and self-unfolding to adapt shape and function to mission phases.

The Influence of Weather Variation, Urban Design and Built Environment on Objectively Measured Sedentary Behaviour in Children.

PubMed

Katapally, Tarun Reddy; Rainham, Daniel; Muhajarine, Nazeem

2016-01-01

With emerging evidence indicating that independent of physical activity, sedentary behaviour (SB) can be detrimental to health, researchers are increasingly aiming to understand the influence of multiple contexts such as urban design and built environment on SB. However, weather variation, a factor that continuously interacts with all other environmental variables, has been consistently underexplored. This study investigated the influence of diverse environmental exposures (including weather variation, urban design and built environment) on SB in children. This cross-sectional observational study is part of an active living research initiative set in the Canadian prairie city of Saskatoon. Saskatoon's neighbourhoods were classified based on urban street design into grid-pattern, fractured grid-pattern and curvilinear types of neighbourhoods. Diverse environmental exposures were measured including, neighbourhood built environment, and neighbourhood and household socioeconomic environment. Actical accelerometers were deployed between April and June 2010 (spring-summer) to derive SB of 331 10-14 year old children in 25 one week cycles. Each cycle of accelerometry was conducted on a different cohort of children within the total sample. Accelerometer data were matched with localized weather patterns derived from Environment Canada weather data. Multilevel modeling using Hierarchical Linear and Non-linear Modeling software was conducted by factoring in weather variation to depict the influence of diverse environmental exposures on SB. Both weather variation and urban design played a significant role in SB. After factoring in weather variation, it was observed that children living in grid-pattern neighbourhoods closer to the city centre (with higher diversity of destinations) were less likely to be sedentary. This study demonstrates a methodology that could be replicated to integrate geography-specific weather patterns with existing cross-sectional accelerometry data to understand the influence of urban design and built environment on SB in children.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stanislavskii, L.Ya.

Large turbogenerators with built-up rotor designs operating in U.S.S.R. power plants were studied to obtain data on reliability, failures, and performance characteristics for normal and abnormal operating conditions. Data for 23 turbogenerators manufactured by domestic and foreign firms were analyzed. The studies showed that the reliability factor of the joints of built-up rotors should be equal to approximately 6 to provide a monolithic built-up rotor. At lower built-up rotor joint reliability factors, weakening of the joints occurred during their operation, leading to extreme generator vibration, damage to the insulating sockets at the joint, burning of the joints and sometimes breakagemore » of the screws holding the joints. When it is necessary to restore the monolithic nature of the joints of a rotor its design should permit replacement of the tightening devices (tie rods, screws). If this is not possible the built-up rotor becomes unsuitable for operation. During abnormal conditions there are maximum temperatures in the joint of a built-up rotor about 50 percent greater than in the end part of the rotor. Thus special structural measures are necessary to improve the electrical contact in the joints of the built-up parts of the rotors of large turbogenerators. In all cases where they are not dictated by construction requirements (supercooled turbogenerators), the use of built-up rotors is unfavorable. (LCL)« less

First on-sun test of NaK pool-boiler solar receiver

NASA Astrophysics Data System (ADS)

Moreno, J. B.; Andraka, C. E.; Moss, T. A.; Cordeiro, P. G.; Dudley, V. E.; Rawlinson, K. S.

During 1989-1990, a refluxing liquid-metal pool-boiler solar receiver designed for dish/Stirling application at 75 kW(sub t) throughput was successfully demonstrated at Sandia National Laboratories. Significant features of this receiver included (1) boiling sodium as the heat transfer medium, and (2) electric-discharge-machined (EDM) cavities as artificial nucleation sites to stabilize boiling. Following this first demonstration, a second-generation pool-boiler receiver that brings the concept closer to commercialization has been designed, constructed, and successfully tested. For long life, the new receiver is built from Haynes Alloy 230. For increased safety factors against film boiling and flooding, the absorber area and vapor-flow passages have been enlarged. To eliminate the need for trace heating, sodium has been replaced by the sodium-potassium alloy NaK-78. To reduce manufacturing costs, the receiver has a powdered-metal coating instead of EDM cavities for stabilization of boiling. To control incipient-boiling superheats, especially during hot restarts, it contains a small amount of xenon. In this paper, we present the receiver design and report the results of on-sun tests using a nominal 75 kW(sub t) test-bed concentrator to characterize boiling stability, hot-restart behavior, and thermal efficiency at temperatures up to 750 C. We also report briefly on late results from an advanced-concepts pool-boiler receiver.

Remote liquid target loading system for LANL two-stage gas gun

NASA Astrophysics Data System (ADS)

Gibson, L. L.; Bartram, B.; Dattelbaum, D. M.; Sheffield, S. A.; Stahl, D. B.

2009-06-01

A Remote Liquid Loading System (RLLS) was designed to load high hazard liquid materials into targets for gas-gun driven impact experiments. These high hazard liquids tend to react with confining materials in a short period of time, degrading target assemblies and potentially building up pressure through the evolution of gas in the reactions. Therefore, the ability to load a gas gun target in place immediately prior to firing the gun, provides the most stable and reliable target fielding approach. We present the design and evaluation of a RLLS built for the LANL two-stage gas gun. Targets for the gun are made of PMMA and assembled to form a liquid containment cell with a volume of approximately 25 cc. The compatibility of materials was a major consideration in the design of the system, particularly for its use with highly concentrated hydrogen peroxide. Teflon and 304-stainless steel were the two most compatible materials with the materials to be tested. Teflon valves and tubing, as well as stainless steel tubing, were used to handle the liquid, along with a stainless steel reservoir. Preliminary testing was done to ensure proper flow rate and safety. The system has been used to successfully load 97.5 percent hydrogen peroxide into a target cell just prior to a successful multiple magnetic gauge experiment. TV cameras on the target verified the bubble-free filling operation.

Simultaneous PET/MR imaging with a radio frequency-penetrable PET insert

PubMed Central

Grant, Alexander M.; Lee, Brian J.; Chang, Chen-Ming; Levin, Craig S.

2017-01-01

Purpose A brain sized radio-frequency (RF)-penetrable PET insert has been designed for simultaneous operation with MRI systems. This system takes advantage of electro-optical coupling and battery power to electrically float the PET insert relative to the MRI ground, permitting RF signals to be transmitted through small gaps between the modules that form the PET ring. This design facilitates the use of the built-in body coil for RF transmission, and thus could be inserted into any existing MR site wishing to achieve simultaneous PET/MR imaging. The PET detectors employ non-magnetic silicon photomultipliers in conjunction with a compressed sensing signal multiplexing scheme, and optical fibers to transmit analog PET detector signals out of the MRI room for decoding, processing, and image reconstruction. Methods The PET insert was first constructed and tested in a laboratory benchtop setting, where tomographic images of a custom resolution phantom were successfully acquired. The PET insert was then placed within a 3T body MRI system, and tomographic resolution/contrast phantom images were acquired both with only the B0 field present, and under continuous pulsing from different MR imaging sequences. Results The resulting PET images have comparable contrast-to-noise ratios (CNR) under all MR pulsing conditions: the maximum percent CNR relative difference for each rod type among all four PET images acquired in the MRI system has a mean of 14.0±7.7%. MR images were successfully acquired through the RF-penetrable PET shielding using only the built-in MR body coil, suggesting that simultaneous imaging is possible without significant mutual interference. Conclusions These results show promise for this technology as an alternative to costly integrated PET/MR scanners; a PET insert that is compatible with any existing clinical MRI system could greatly increase the availability, accessibility, and dissemination of PET/MR. PMID:28102949

A Climate of Excellence: Paving the Way for Student Success at Miami-Dade South's Library.

ERIC Educational Resources Information Center

Watters, Robert D.

1986-01-01

Describes Miami-Dade Community College and its librarians. Examines ways South Campus has built, stretched, and promoted the use of library resources. Discusses several student success-oriented strategies; e.g., self-guided cassette tours, "Time Savers" study guides, self-instructional library skills programs, audiovisual productions,…

Design of an automated cart and mount for a hyperspectral imaging system to be used in produce fields

NASA Astrophysics Data System (ADS)

Lefcourt, Alan M.; Kistler, Ross; Gadsden, S. Andrew

2016-05-01

The goal of this project was to construct a cart and a mounting system that would allow a hyperspectral laser-induced fluorescence imaging system (HLIFIS) to be used to detect fecal material in produce fields. Fecal contaminated produce is a recognized food safety risk. Previous research demonstrated the HLIFIS could detect fecal contamination in a laboratory setting. A cart was designed and built, and then tested to demonstrate that the cart was capable of moving at constant speeds or at precise intervals. A mounting system was designed and built to facilitate the critical alignment of the camera's imaging and the laser's illumination fields, and to allow the HLIFIS to be used in both field and laboratory settings without changing alignments. A hardened mount for the Powell lens that is used to produce the appropriate illumination profile was also designed, built, and tested.

Potential clinical impact of advanced imaging and computer-aided diagnosis in chest radiology: importance of radiologist's role and successful observer study.

PubMed

Li, Feng

2015-07-01

This review paper is based on our research experience in the past 30 years. The importance of radiologists' role is discussed in the development or evaluation of new medical images and of computer-aided detection (CAD) schemes in chest radiology. The four main topics include (1) introducing what diseases can be included in a research database for different imaging techniques or CAD systems and what imaging database can be built by radiologists, (2) understanding how radiologists' subjective judgment can be combined with technical objective features to improve CAD performance, (3) sharing our experience in the design of successful observer performance studies, and (4) finally, discussing whether the new images and CAD systems can improve radiologists' diagnostic ability in chest radiology. In conclusion, advanced imaging techniques and detection/classification of CAD systems have a potential clinical impact on improvement of radiologists' diagnostic ability, for both the detection and the differential diagnosis of various lung diseases, in chest radiology.

Purpose-built PDC bit successfully drills 7-in liner equipment and formation: An integrated solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Puennel, J.G.A.; Huppertz, A.; Huizing, J.

1996-12-31

Historically, drilling out the 7-in, liner equipment has been a time consuming operation with a limited success ratio. The success of the operation is highly dependent on the type of drill bit employed. Tungsten carbide mills and mill tooth rock bits required from 7.5 to 11.5 hours respectively to drill the pack-off bushings, landing collar, shoe track and shoe. Rates of penetration dropped dramatically when drilling the float equipment. While conventional PDC bits have drilled the liner equipment successfully (averaging 9.7 hours), severe bit damage invariably prevented them from continuing to drill the formation at cost-effective penetration rates. This papermore » describes the integrated development and application of an IADC M433 Class PDC bit, which was designed specifically to drill out the 7-in. liner equipment and continue drilling the formation at satisfactory penetration rates. The development was the result of a joint investigation There the operator and bit/liner manufacturers shared their expertise in solving a drilling problem, The heavy-set bit was developed following drill-off tests conducted to investigate the drillability of the 7-in. liner equipment. Key features of the new bit and its application onshore The Netherlands will be presented and analyzed.« less

Influence of core design, production technique, and material selection on fracture behavior of yttria-stabilized tetragonal zirconia polycrystal fixed dental prostheses produced using different multilayer techniques: split-file, over-pressing, and manually built-up veneers.

PubMed

Mahmood, Deyar Jallal Hadi; Linderoth, Ewa H; Wennerberg, Ann; Vult Von Steyern, Per

2016-01-01

To investigate and compare the fracture strength and fracture mode in eleven groups of currently, the most commonly used multilayer three-unit all-ceramic yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) fixed dental prostheses (FDPs) with respect to the choice of core material, veneering material area, manufacturing technique, design of connectors, and radii of curvature of FDP cores. A total of 110 three-unit Y-TZP FDP cores with one intermediate pontic were made. The FDP cores in groups 1-7 were made with a split-file design, veneered with manually built-up porcelain, computer-aided design-on veneers, and over-pressed veneers. Groups 8-11 consisted of FDPs with a state-of-the-art design, veneered with manually built-up porcelain. All the FDP cores were subjected to simulated aging and finally loaded to fracture. There was a significant difference (P<0.05) between the core designs, but not between the different types of Y-TZP materials. The split-file designs with VITABLOCS(®) (1,806±165 N) and e.max(®) ZirPress (1,854±115 N) and the state-of-the-art design with VITA VM(®) 9 (1,849±150 N) demonstrated the highest mean fracture values. The shape of a split-file designed all-ceramic reconstruction calls for a different dimension protocol, compared to traditionally shaped ones, as the split-file design leads to sharp approximal indentations acting as fractural impressions, thus decreasing the overall strength. The design of a framework is a crucial factor for the load bearing capacity of an all-ceramic FDP. The state-of-the-art design is preferable since the split-file designed cores call for a cross-sectional connector area at least 42% larger, to have the same load bearing capacity as the state-of-the-art designed cores. All veneering materials and techniques tested in the study, split-file, over-press, built-up porcelains, and glass-ceramics are, with a great safety margin, sufficient for clinical use both anteriorly and posteriorly. Analysis of the fracture pattern shows differences between the milled veneers and over-pressed or built-up veneers, where the milled ones show numerically more veneer cracks and the other groups only show complete connector fractures.

Maximum Power Point Tracking Control of Hydrokinetic Turbine and Low-speed High-Thrust Permanent Magnet Generator Design

DTIC Science & Technology

2012-01-01

Schematic of the generator and power converters built in PLECS ............. 26 Figure 3.12. Block diagram of the MPPT control built in Matlab/Simulink...validated by simulation results done in Matlab/Simulink R2010a and PLECS . Figure 3.9 shows the block diagram of the hydrokinetic system built in Matlab...rectifier, boost converter and battery model built in PLECS . The battery bank on the load side is simulated by a constant dc voltage source. 25

The X-38 Spacecraft Fault-Tolerant Avionics System

NASA Technical Reports Server (NTRS)

Kouba,Coy; Buscher, Deborah; Busa, Joseph

2003-01-01

In 1995 NASA began an experimental program to develop a reusable crew return vehicle (CRV) for the International Space Station. The purpose of the CRV was threefold: (i) to bring home an injured or ill crewmember; (ii) to bring home the entire crew if the Shuttle fleet was grounded; and (iii) to evacuate the crew in the case of an imminent Station threat (i.e., fire, decompression, etc). Built at the Johnson Space Center, were two approach and landing prototypes and one spacecraft demonstrator (called V201). A series of increasingly complex ground subsystem tests were completed, and eight successful high-altitude drop tests were achieved to prove the design concept. In this program, an unprecedented amount of commercial-off-the-shelf technology was utilized in this first crewed spacecraft NASA has built since the Shuttle program. Unfortunately, in 2002 the program was canceled due to changing Agency priorities. The vehicle was 80% complete and the program was shut down in such a manner as to preserve design, development, test and engineering data. This paper describes the X-38 V201 fault-tolerant avionics system. Based on Draper Laboratory's Byzantine-resilient fault-tolerant parallel processing system and their "network element" hardware, each flight computer exchanges information on a strict timescale to process input data, compare results, and issue voted vehicle output commands. Major accomplishments achieved in this development include: (i) a space qualified two-fault tolerant design using mostly COTS (hardware and operating system); (ii) a single event upset tolerant network element board, (iii) on-the-fly recovery of a failed processor; (iv) use of synched cache; (v) realignment of memory to bring back a failed channel; (vi) flight code automatically generated from the master measurement list; and (vii) built in-house by a team of civil servants and support contractors. This paper will present an overview of the avionics system and the hardware implementation, as well as the system software and vehicle command & telemetry functions. Potential improvements and lessons learned on this program are also discussed.

Multilevel modelling of built environment characteristics related to neighbourhood walking activity in older adults

PubMed Central

Li, F.; Fisher, K; Brownson, R.; Bosworth, M.

2005-01-01

Objective: To examine the relation between built environment factors (representing several dimensions of urban form of neighbourhoods) and walking activity at both the neighbourhood level and the resident level, in an older adult sample. Design, setting, participants: A cross sectional, multilevel design with neighbourhoods as the primary sampling unit and senior residents as the secondary unit. Five hundred and seventy seven residents (mean age = 74 years, SD = 6.3 years) participated in the survey, which was conducted among 56 city defined neighbourhoods in Portland, Oregon, USA. Neighbourhood level variables were constructed using geographical information systems. Resident level variables consisted of a mix of self reports and geocoded data on the built environment. Main outcome measure: Self reported neighbourhood walking. Main results: A positive relation was found between built environment factors (density of places of employment, household density, green and open spaces for recreation, number of street intersections) and walking activity at the neighbourhood level. At the resident level, perceptions of safety for walking and number of nearby recreational facilities were positively related to high levels of walking activity. A significant interaction was observed between number of street intersections and perceptions of safety from traffic. Conclusions: Certain neighbourhood built environment characteristics related to urban form were positively associated with walking activity in the neighbourhoods of senior residents. Public health promotion of walking activity/urban mobility and the design of interventions need to consider the contribution of neighbourhood level built environment influences. PMID:15965138

Design of a New Built-in UHF Multi-Frequency Antenna Sensor for Partial Discharge Detection in High-Voltage Switchgears.

PubMed

Zhang, Xiaoxing; Cheng, Zheng; Gui, Yingang

2016-07-26

In this study a new built-in ultrahigh frequency (UHF) antenna sensor was designed and applied in a high-voltage switchgear for partial discharge (PD) detection. The casing of the switchgear was initially used as the ground plane of the antenna sensor, which integrated the sensor into the high-voltage switchgear. The Koch snowflake patch was adopted as the radiation patch of the antenna to overcome the disadvantages of common microstrip antennas, and the feed position and the dielectric layer thickness were simulated in detail. Simulation results show that the antenna sensor possessed four resonant points with good impedance matching from 300 MHz to 1000 MHz, and it also presented good multi-frequency performance in the entire working frequency band. PD detection experiments were conducted in the high-voltage switchgear, and the fabricated antenna sensor was effectively built into the high-voltage switchgear. In order to reflect the advantages of the built-in antenna sensor, another external UHF antenna sensor was used as a comparison to simultaneously detect PD. Experimental results demonstrated that the built-in antenna sensor possessed high detection sensitivity and strong anti-interference capacity, which ensured the practicability of the design. In addition, it had more high-voltage switchgear PD detection advantages than the external sensor.

Design of a New Built-in UHF Multi-Frequency Antenna Sensor for Partial Discharge Detection in High-Voltage Switchgears

PubMed Central

Zhang, Xiaoxing; Cheng, Zheng; Gui, Yingang

2016-01-01

In this study a new built-in ultrahigh frequency (UHF) antenna sensor was designed and applied in a high-voltage switchgear for partial discharge (PD) detection. The casing of the switchgear was initially used as the ground plane of the antenna sensor, which integrated the sensor into the high-voltage switchgear. The Koch snowflake patch was adopted as the radiation patch of the antenna to overcome the disadvantages of common microstrip antennas, and the feed position and the dielectric layer thickness were simulated in detail. Simulation results show that the antenna sensor possessed four resonant points with good impedance matching from 300 MHz to 1000 MHz, and it also presented good multi-frequency performance in the entire working frequency band. PD detection experiments were conducted in the high-voltage switchgear, and the fabricated antenna sensor was effectively built into the high-voltage switchgear. In order to reflect the advantages of the built-in antenna sensor, another external UHF antenna sensor was used as a comparison to simultaneously detect PD. Experimental results demonstrated that the built-in antenna sensor possessed high detection sensitivity and strong anti-interference capacity, which ensured the practicability of the design. In addition, it had more high-voltage switchgear PD detection advantages than the external sensor. PMID:27472331

Computer-Automated Evolution of Spacecraft X-Band Antennas

NASA Technical Reports Server (NTRS)

Lohn, Jason D.; Homby, Gregory S.; Linden, Derek S.

2010-01-01

A document discusses the use of computer- aided evolution in arriving at a design for X-band communication antennas for NASA s three Space Technology 5 (ST5) satellites, which were launched on March 22, 2006. Two evolutionary algorithms, incorporating different representations of the antenna design and different fitness functions, were used to automatically design and optimize an X-band antenna design. A set of antenna designs satisfying initial ST5 mission requirements was evolved by use these algorithms. The two best antennas - one from each evolutionary algorithm - were built. During flight-qualification testing of these antennas, the mission requirements were changed. After minimal changes in the evolutionary algorithms - mostly in the fitness functions - new antenna designs satisfying the changed mission requirements were evolved and within one month of this change, two new antennas were designed and prototypes of the antennas were built and tested. One of these newly evolved antennas was approved for deployment on the ST5 mission, and flight-qualified versions of this design were built and installed on the spacecraft. At the time of writing the document, these antennas were the first computer-evolved hardware in outer space.

Semiconductor laser joint study program with Rome Laboratory

NASA Astrophysics Data System (ADS)

Schaff, William J.; Okeefe, Sean S.; Eastman, Lester F.

1994-09-01

A program to jointly study vertical-cavity surface emitting lasers (VCSEL) for high speed vertical optical interconnects (VOI) has been conducted under an ES&E between Rome Laboratory and Cornell University. Lasers were designed, grown, and fabricated at Cornell University. A VCSEL measurement laboratory has been designed, built, and utilized at Rome Laboratory. High quality VCSEL material was grown and characterized by fabricating conventional lateral cavity lasers that emitted at the design wavelength of 1.04 microns. The VCSEL's emit at 1.06 microns. Threshold currents of 16 mA at 4.8 volts were obtained for 30 microns diameter devices. Output powers of 5 mW were measured. This is 500 times higher power than from the light emitting diodes employed previously for vertical optical interconnects. A new form of compositional grading using a cosinusoidal function has been developed and is very successful for reducing diode series resistance for high speed interconnection applications. A flip-chip diamond package compatible with high speed operation of 16 VCSEL elements has been designed and characterized. A flip-chip device binding effort at Rome Laboratory was also designed and initiated. This report presents details of the one-year effort, including process recipes and results.

A Mastery Rubric: guiding curriculum design, admissions and development of course objectives.

PubMed

Tractenberg, Rochelle E; Umans, Jason G; McCarter, Robert J

This article describes a 'Mastery Rubric' (MR) used to design both the curriculum and the assessments in a new two-year certificate programme intended to train physicians in clinical research skills. The MR for clinical research skills is built around a set of core research skills: critical review of literature; articulation of research objective; development of research design; development of analysis plan; implementation of the study; implementation of the analysis plan and presentation of results. Four distinct levels of performance are described for each skill: beginning, novice, competent and proficient. This rubric outlines and provides a path to mastery of the clinical research skills the certificate programme was designed and funded to target. Using the rubric to design the curriculum ensures that courses will provide instruction in key domains, promotes assessment that demonstrates development in the target skills and knowledge, and encourages reflection and cognitive self-monitoring in the students. It is a flexible, criterion-referenced definition of 'success' for students as well as the programme itself. The criteria are characterised in terms of the skills, habits of mind and organisational principles that can foster excellence in clinical research, but the approach can be generalised.

Design of an ion thruster movable grid thrust vectoring system

NASA Astrophysics Data System (ADS)

Kural, Aleksander; Leveque, Nicolas; Welch, Chris; Wolanski, Piotr

2004-08-01

Several reasons justify the development of an ion propulsion system thrust vectoring system. Spacecraft launched to date have used ion thrusters mounted on gimbals to control the thrust vector within a range of about ±5°. Such devices have large mass and dimensions, hence the need exists for a more compact system, preferably mounted within the thruster itself. Since the 1970s several thrust vectoring systems have been developed, with the translatable accelerator grid electrode being considered the most promising. Laboratory models of this system have already been built and successfully tested, but there is still room for improvement in their mechanical design. This work aims to investigate possibilities of refining the design of such movable grid thrust vectoring systems. Two grid suspension designs and three types of actuators were evaluated. The actuators examined were a micro electromechanical system, a NanoMuscle shape memory alloy actuator and a piezoelectric driver. Criteria used for choosing the best system included mechanical simplicity (use of the fewest mechanical parts), accuracy, power consumption and behaviour in space conditions. Designs of systems using these actuators are proposed. In addition, a mission to Mercury using the system with piezoelectric drivers has been modelled and its performance presented.

A Laboratory Experiment to Measure the Built-In Potential of a P-N Junction by a Photosaturation Method

ERIC Educational Resources Information Center

Ikram, I. Mohamed; Rabinal, M. K.; Mulimani, B. G.

2009-01-01

Here, we propose a simple method for measuring the built-in potential and its temperature dependence of a photodiode by a photosaturation technique. The experimental design facilitates both current-voltage and null voltage measurements as a function of white light intensity. This method gives the built-in potential directly; as a result its…

Human Behavior and Environmental Sustainability: promoting a pro-environmental behavior by harnessing the social, psychological and physical influences of the built environment

NASA Astrophysics Data System (ADS)

Abusafieh, Shaden; Razem, Maiss

2017-11-01

Recently, technological advancements in the sustainable design field have allowed us to reduce the ecological impact of the built environment, to reduce consumption of non-renewable resources, to create healthy environments and in some cases may even rehabilitate the ecosystem. Nevertheless, several studies have been carried out showing that sustainable technology does not automatically lead to environmentally friendly behaviors in its users. Various environmental problems threaten environmental sustainability and many of these problems are rooted in human behavior. Unfortunately, there is a lack in studies which take into consideration the human behavior influences within a sustainable built environment. We believe that the built environment should be used to support human goals and requirements, but at the same time we should consider it as a context in which human values and behaviors are cultivated. This research aimed to help in promoting environmental sustainability by using architectural design in changing relevant human behavior toward an environmentally friendly behavior. In order to achieve this, the research adopted Environment-centered Approach to gain more acute perspective into the relationship between the physical environment and human behavior, focusing on social, psychological and physical influences of the built environment. It appears that environmental psychology's merits have high potential in changing behavior within the built environment. The research provides a systematic approach for selecting, assessing, evaluating the behaviors to be changed and the factors that determine them. Furthermore, this approach helps in choosing the best interventions that could be applied in built environment to encourage such a sustainable behavior. This study tried to construct an agenda for further researches to find particular architectural design elements and strategies that we can harness to develop a pro-environment human behavior.

Design and implementation of smart sensor nodes for wireless disaster monitoring systems

NASA Astrophysics Data System (ADS)

Chen, Yih-Fan; Wu, Wen-Jong; Chen, Chun-Kuang; Wen, Chih-Min; Jin, Ming-Hui; Gau, Chung-Yun; Chang, Chih-Chie; Lee, Chih-Kung

2004-07-01

A newly developed smart sensor node that can monitor the safety of temporary structures such as scaffolds at construction sites is detailed in this paper. The design methodology and its trade-offs, as well as its influence on the optimization of sensor networks, is examined. The potential impact on civil engineering construction sites, environmental and natural disaster pre-warning issues, etc., all of which are foundations of smart sensor nodes and corresponding smart sensor networks, is also presented. To minimize the power requirements in order to achieve a true wireless system both in terms of signal and power, a sensor node was designed by adopting an 8051-based micro-controller, an ISM band RF transceiver, and an auto-balanced strain gage signal conditioner. With the built-in RF transceiver, all measurement data can be transmitted to a local control center for data integrity, security, central monitoring, and full-scale analysis. As a battery is the only well-established power source and there is a strong desire to eliminate the need to install bulky power lines, this system designed includes a battery-powered core with optimal power efficiency. To further extend the service life of the built-in power source, a power control algorithm has been embedded in the microcontroller of each sensor node. The entire system has been verified by experimental tests on full-scale scaffold monitoring. The results show that this system provides a practical method to monitor the structure safety in real time and possesses the potential of reducing maintenance costs significantly. The design of the sensor node, central control station, and the integration of several kinds of wireless communication protocol, all of which are successfully integrated to demonstrate the capabilities of this newly developed system, are detailed. Potential impact to the network topology is briefly examined as well.

Germany's Option for a Moon Satellite

NASA Astrophysics Data System (ADS)

Quantius, Dominik

The German non-profit amateur satellite organisation AMSAT-Deutschland successfully de-signed, built and launched four HEO satellites in the last three decades. Now they are going to build a satellite to leave the Earth orbit based on their flight-proven P3-D satellite design. Due to energetic constraints the most suitable launch date for the planned P5-A satellite to Mars will be in 2018. To efficiently use the relatively long time gap until launch a possible prior Moon mission came into mind. In co-operation with the DLR-Institute of Space Systems in Bremen, Germany, two studies on systems level for a first P5 satellite towards Moon and a following one towards Mars have been performed. By using the DLR's Concurrent Engineering Facility (CEF) two consistent satellite concepts were designed including mission analysis, configuration, propulsion, subsystem dimensioning, payload selection, budgeting and cost. The present paper gives an insight in the accomplished design process and the results of the performed study towards Moon. The developed Moon orbiter is designed to carry the following four main instruments besides flexible communication abilities: • slewable HDTV camera combined with a high gain antenna that allows receiving lunar television using a commercially available satellite TV dish on Earth • sensor imaging infrared spectrometer for mineralogy of lunar silicates and lunar surface temperature measurements • camera for detection and monitoring of impact flashes in visible light (VIS) on lunar night side caused by meteoroid impact events • camera technology test for interplanetary navigation and planetary approach navigation. This study presents a non-industrial satellite concept that could be launched as piggyback load on Ariane 5 into GTO. Due to the fact, that the satellite would be built by the private sector, the mission costs would remain low. Otherwise the scientific and public output would be high using that satellite bus for the instruments contributed by DLR.

Fluid-Structure Interaction in a Fluid-Filled Composite Structure Subjected to Low Velocity Impact

DTIC Science & Technology

2016-06-01

for creating an E-glass composite cubic structure and a pendulum was designed and built to provide a repeatable low velocity impact. The behavior of...structure and a pendulum was designed and built to provide a repeatable low velocity impact. The behavior of the composite structure was studied at various...SET-UP .......................................................31  1.  Impact Pendulum

CESIC: a new technology for lightweight and cost effective space instrument structures and mirrors

NASA Astrophysics Data System (ADS)

Devilliers, Christophe; Kroedel, Matthias R.

2005-08-01

For some years Alcatel Space has been interested in the development of a new material to produce lightweight, stiff, stable and cost effective structures and mirrors for space instrument. Cesic from ECM has been selected for its intrinsic properties (high specific modulus, high conductivity, quite low thermal expansion coefficient and high fracture toughness for a ceramic material), added to ample manufacturing capabilities. Under ESA responsibility, a flight representative optical bench of Cesic has been designed, manufactured and tested. The optical bench has been submitted with success to intensive vibration tests up to 80 g on shaker without problem and was tested down to 30 K showing very high stability. Cesic is also envisaged for large and lightweight space telescope mirrors. Coatings on the Cesic substrate have been developed and qualified for the most stringent optical needs. To prove the lightweight capability, a large Cesic mirror D=950 mm with an area mass of less than 25 kg/m2 has been designed, sized again launch loads and WFE performance, and then manufactured. Cesic is also envisaged for large future focal plane holding a large number of detectors assuring high stability thanks to its high thermal conductivity. A full size Cesic focal plane has been already successfully built and tested. Based on these successful results, Alcatel Space is now in position to propose for space projects this technology mastered in common with ECM both for mirrors and structures with new innovative concepts thanks to the manufacturing capabilities of this technology.

Universal Payload Information Management

NASA Technical Reports Server (NTRS)

Elmore, Ralph B.

2003-01-01

As the overall manager and integrator of International Space Station (ISS) science payloads, the Payload Operations Integration Center (POIC) at Marshall Space Flight Center has a critical need to provide an information management system for exchange and control of ISS payload files as well as to coordinate ISS payload related operational changes. The POIC's information management system has a fundamental requirement to provide secure operational access not only to users physically located at the POIC, but also to remote experimenters and International Partners physically located in different parts of the world. The Payload Information Management System (PIMS) is a ground-based electronic document configuration management and collaborative workflow system that was built to service the POIC's information management needs. This paper discusses the application components that comprise the PIMS system, the challenges that influenced its design and architecture, and the selected technologies it employs. This paper will also touch on the advantages of the architecture, details of the user interface, and lessons learned along the way to a successful deployment. With PIMS, a sophisticated software solution has been built that is not only universally accessible for POIC customer s information management needs, but also universally adaptable in implementation and application as a generalized information management system.

Study on soil-pile-structure-TMD interaction system by shaking table model test

NASA Astrophysics Data System (ADS)

Lou, Menglin; Wang, Wenjian

2004-06-01

The success of the tuned mass damper (TMD) in reducing wind-induced structural vibrations has been well established. However, from most of the recent numerical studies, it appears that for a structure situated on very soft soil, soil-structure interaction (SSI) could render a damper on the structure totally ineffective. In order to experimentally verify the SSI effect on the seismic performance of TMD, a series of shaking table model tests have been conducted and the results are presented in this paper. It has been shown that the TMD is not as effective in controlling the seismic responses of structures built on soft soil sites due to the SSI effect. Some test results also show that a TMD device might have a negative impact if the SSI effect is neglected and the structure is built on a soft soil site. For structures constructed on a soil foundation, this research verifies that the SSI effect must be carefully understood before a TMD control system is designed to determine if the control is necessary and if the SSI effect must be considered when choosing the optimal parameters of the TMD device.

Gamma Ray Large Area Space Telescope (GLAST) Balloon Flight Engineering Model: Overview

NASA Technical Reports Server (NTRS)

Thompson, D. J.; Godfrey, G.; Williams, S. M.; Grove, J. E.; Mizuno, T.; Sadrozinski, H. F.-W.; Kamae, T.; Ampe, J.; Briber, Stuart; Dann, James;

Long term monitoring of the optical background in the Capo Passero deep-sea site with the NEMO tower prototype

NASA Astrophysics Data System (ADS)

Adrián-Martínez, S.; Aiello, S.; Ameli, F.; Anghinolfi, M.; Ardid, M.; Barbarino, G.; Barbarito, E.; Barbato, F. C. T.; Beverini, N.; Biagi, S.; Biagioni, A.; Bouhadef, B.; Bozza, C.; Cacopardo, G.; Calamai, M.; Calì, C.; Calvo, D.; Capone, A.; Caruso, F.; Ceres, A.; Chiarusi, T.; Circella, M.; Cocimano, R.; Coniglione, R.; Costa, M.; Cuttone, G.; D'Amato, C.; D'Amico, A.; De Bonis, G.; De Luca, V.; Deniskina, N.; De Rosa, G.; di Capua, F.; Distefano, C.; Enzenhöfer, A.; Fermani, P.; Ferrara, G.; Flaminio, V.; Fusco, L. A.; Garufi, F.; Giordano, V.; Gmerk, A.; Grasso, R.; Grella, G.; Hugon, C.; Imbesi, M.; Kulikovskiy, V.; Lahmann, R.; Larosa, G.; Lattuada, D.; Leismüller, K. P.; Leonora, E.; Litrico, P.; Llorens Alvarez, C. D.; Lonardo, A.; Longhitano, F.; Lo Presti, D.; Maccioni, E.; Margiotta, A.; Marinelli, A.; Martini, A.; Masullo, R.; Migliozzi, P.; Migneco, E.; Miraglia, A.; Mollo, C. M.; Mongelli, M.; Morganti, M.; Musico, P.; Musumeci, M.; Nicolau, C. A.; Orlando, A.; Orzelli, A.; Papaleo, R.; Pellegrino, C.; Pellegriti, M. G.; Perrina, C.; Piattelli, P.; Pugliatti, C.; Pulvirenti, S.; Raffaelli, F.; Randazzo, N.; Real, D.; Riccobene, G.; Rovelli, A.; Saldaña, M.; Sanguineti, M.; Sapienza, P.; Sciacca, V.; Sgura, I.; Simeone, F.; Sipala, V.; Speziale, F.; Spitaleri, A.; Spurio, M.; Stellacci, S. M.; Taiuti, M.; Terreni, G.; Trasatti, L.; Trovato, A.; Ventura, C.; Vicini, P.; Viola, S.; Vivolo, D.

2016-02-01

The NEMO Phase-2 tower is the first detector which was operated underwater for more than 1 year at the "record" depth of 3500 m. It was designed and built within the framework of the NEMO (NEutrino Mediterranean Observatory) project. The 380 m high tower was successfully installed in March 2013 80 km offshore Capo Passero (Italy). This is the first prototype operated on the site where the Italian node of the KM3NeT neutrino telescope will be built. The installation and operation of the NEMO Phase-2 tower has proven the functionality of the infrastructure and the operability at 3500 m depth. A more than 1 year long monitoring of the deep water characteristics of the site has been also provided. In this paper the infrastructure and the tower structure and instrumentation are described. The results of long term optical background measurements are presented. The rates show stable and low baseline values, compatible with the contribution of ^{40}K light emission, with a small percentage of light bursts due to bioluminescence. All these features confirm the stability and good optical properties of the site.

A cognitive perspective on technology enhanced learning in medical training: great opportunities, pitfalls and challenges.

PubMed

Dror, Itiel; Schmidt, Pascal; O'connor, Lanty

2011-01-01

As new technology becomes available and is used for educational purposes, educators often take existing training and simply transcribe it into the new technological medium. However, when technology drives e-learning rather than the learner and the learning, and when it uses designs and approaches that were not originally built for e-learning, then often technology does not enhance the learning (it may even be detrimental to it). The success of e-learning depends on it being 'brain friendly', on engaging the learners from an understanding of how the cognitive system works. This enables educators to optimize learning by achieving correct mental representations that will be remembered and applied in practice. Such technology enhanced learning (TEL) involves developing and using novel approaches grounded in cognitive neuroscience; for example, gaming and simulations that distort realism rather than emphasizing visual fidelity and realism, making videos interactive, training for 'error recovery' rather than for 'error reduction', and a whole range of practical ways that result in effective TEL. These are a result of e-learning that is built to fit and support the cognitive system, and therefore optimize the learning.

Gifford-McMahon refrigerator with split cold head

NASA Technical Reports Server (NTRS)

Forth, H. J.; Heisig, R.; Klein, H. H.

1983-01-01

Leybold-Heraeus Co. have developed, built and successfully tested a Gifford-McMahon cryocooler with splitted cold head for cooling a cryopump. The refrigerating part of the cold head and the gas flow control device have been separated (splitted cold head) and the distance between them is bridged by only two thin lines for carrying the working gas. Due to this separation the size of the refrigerating part is virtually defined only by the size of the displacers whilst the gas flow control device can be of any desired design. It has been shown that dimensioning of the connecting lines and the corresponding losses became less critical with increasing size of the expander, but additional cooling in proportion to the refrigerating capacity is required.

Solar powered rotorcraft: a multidisciplinary engineering challenge for undergraduate students

NASA Astrophysics Data System (ADS)

Danner, Aaron J.; Henz, Martin; Teo, Brian Shohei

2017-08-01

Controlled, fully solar-powered flight in a rotorcraft is a difficult engineering challenge. Over the past five years, multidiciplinary teams of undergraduate engineering students at the National University of Singapore have built and test-flown a succession of increasingly impressive and larger, more efficient aircraft. While many other multidisciplinary or purely photonics projects are available to students in our programme, this particular project attracts an unusual level of excitement and devotion among students working on it. Why is that the case, and what, in general, makes a good final year undergraduate design project? These questions will be explored. Additionally, videos of solar helicopter test flights and spectacular crashes will be shown in the presentation for which the proceedings below have been prepared.

Final Report for the Advanced Camera for Surveys (ACS)

NASA Technical Reports Server (NTRS)

2004-01-01

ACS was launched aboard the Space Shuttle Columbia just before dawn on March 1, 2002. At the time of liftoff, the Hubble Space Telescope (HST) was reflecting the early morning sun as it moved across the sky. After successfully docking with HST, several components were replaced. One of the components was the Advanced Camera for Surveys built by Ball Aerospace & Technologies Corp. (BATC) in Boulder, Colorado. Over the life of the HST contract at BATC, hundreds of employees had the pleasure of working on the concept, design, fabrication, assembly, and test of ACS. Those employees thank NASA - Goddard Space Flight Center and the science team at Johns Hopkins University (JHU) for the opportunity to participate in building a great science instrument for HST.

An investigation of turbulence structure in a low-Reynolds-number incompressible turbulent boundary

NASA Technical Reports Server (NTRS)

White, B. R.; Strataridakis, C. J.

1987-01-01

An existing high turbulence intensity level (5%) atmospheric boundary-layer wind tunnel has been successfully converted to a relatively low level turbulence (0.3%) wind tunnel through extensive modification, testing, and calibration. A splitter plate was designed, built, and installed into the wind-tunnel facility to create thick, mature, two-dimensional turbulent boundary layer flow at zero pressure gradient. Single and cross hot-wire measurements show turbulent boundary layer characteristics of good quality with unusually large physical size, i.e., viscous sublayer of the order of 1 mm high. These confirm the potential ability of the tunnel to be utilized for future high-quality near-wall turbulent boundary layer measurements. It compares very favorably with many low turbulence research tunnels.

Benchmarking transportation logistics practices for effective system planning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thrower, A.W.; Dravo, A.N.; Keister, M.

2007-07-01

This paper presents preliminary findings of an Office of Civilian Radioactive Waste Management (OCRWM) benchmarking project to identify best practices for logistics enterprises. The results will help OCRWM's Office of Logistics Management (OLM) design and implement a system to move spent nuclear fuel (SNF) and high-level radioactive waste (HLW) to the Yucca Mountain repository for disposal when that facility is licensed and built. This report suggests topics for additional study. The project team looked at three Federal radioactive material logistics operations that are widely viewed to be successful: (1) the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico; (2)more » the Naval Nuclear Propulsion Program (NNPP); and (3) domestic and foreign research reactor (FRR) SNF acceptance programs. (authors)« less

Lunar Regolith Excavation Competition

NASA Technical Reports Server (NTRS)

Liles, Cassandra

2009-01-01

The Lunar Regolith Excavation Competition is a new competition that needs graphics, logos, rules, as well as an arena. Although this is the first year of the competition, the competition is modeled after an existing competition, the Centennial Lunar Excavator Challenge. This competition however is aimed at college students. This makes the challenge identifying key aspects of the original competition and modeling them to fit into an easier task, and creating exciting advertisement that helps encourage participation. By using a youth focus group, young insight, as well as guiding advice from experts in the field, hopefully an arena can be designed and built, rules can be molded and created to fit, and alluring graphics can be printed to bring about a successful first year of the Lunar Regolith Excavation Competition.

Organo-metallic elements for associative information processing

NASA Astrophysics Data System (ADS)

Potember, Richard S.; Poehler, Theodore O.

1989-01-01

In the three years of the program we have: (1) built and tested a 4 bit element matrix device for possible use in high density content-addressable memories systems; (2) established a test and evaluation laboratory to examine optical materials for nonlinear effects, saturable absorption, harmonic generation and photochromism; (3) successfully designed, constructed and operated a codeposition processing system that enables organic materials to be deposited on a variety of substrates to produce optical grade coatings and films. This system is also compatible with other traditional microelectronic techniques; (4) used the sol-gel process with colloidal AgTCNQ to fabricate high speed photochromic switches; (5) develop and applied for patent coverage to make VO2 optical switching materials via the sol-gel processing using vanadium (IV) alkoxide compounds.

High-frequency characterization and modeling of single metallic nanowires

NASA Astrophysics Data System (ADS)

Hsu, Chuan-Lun; Ardila, Gustavo; Benech, Philippe

2013-07-01

The transmission line characteristics of an individual aluminum metallic nanowire up to 100 GHz are presented in this paper. We have built a reliable framework for characterizing such nanowires using a specially designed coplanar waveguide platform. We systematically estimate the pad parasitics, contact impedance and transmission line parameters based on an equivalent circuit model and cascade-based de-embedding theory. This is the first time that such external parasitic elements have been successfully removed from a nanoscale transmission line. The extracted frequency-dependent electrical responses show good signal levels and a high degree of reproducibility. Contribution to the Topical Issue “International Semiconductor Conference Dresden-Grenoble - ISCDG 2012”, Edited by Gérard Ghibaudo, Francis Balestra and Simon Deleonibus.

Technical and commerical challenges in high Tc SQUIDs and their industrial applications

NASA Technical Reports Server (NTRS)

Lu, D. F.

1995-01-01

A SQUID is the most sensitive device for measuring changes in magnetic flux. Since its discovery in the sixties, scientists have made consistent efforts to apply SQUID's to various applications. Instruments that are the most sensitive in their respective categories have been built, such as SQUID DC susceptometer that is now manufactured by Quantum Design, pico-voltmeter which could measure 10(exp -14) volts, and gravitational wave detectors. One of the most successful applications of SQUID's is in magnetoencephalography, a non-invasive technique for investigating neuronal activity in the living human brain. This technique employs a multi-channel SQUID magnetometer that maps the weak magnetic field generated by small current when information is processed in brain, and its performance is marvelous.

Design and Operation of a 4kW Linear Motor Driven Pulse Tube Cryocooler

NASA Astrophysics Data System (ADS)

Zia, J. H.

2004-06-01

A 4 kW electrical input Linear Motor driven pulse tube cryocooler has successfully been designed, built and tested. The optimum operation frequency is 60 Hz with a design refrigeration of >200 W at 80 K. The design exercise involved modeling and optimization in DeltaE software. Load matching between the cold head and linear motor was achieved by careful sizing of the transfer tube. The cryocooler makes use of a dual orifice inertance network and a single compliance tank for phase optimization and streaming suppression in the pulse tube. The in-line cold head design is modular in structure for convenient change-out and re-assembly of various components. The Regenerator consists of layers of two different grades of wire-mesh. The Linear motor is a clearance seal, dual opposed piston design from CFIC Inc. Initial results have demonstrated the refrigeration target of 200 W by liquefying Nitrogen from an ambient temperature and pressure. Overall Carnot efficiencies of 13% have been achieved and efforts to further improve efficiencies are underway. Linear motor efficiencies up to 84% have been observed. Experimental results have shown satisfactory compliance with model predictions, although the effects of streaming were not part of the model. Refrigeration loss due to streaming was minimal at the design operating conditions of 80 K.

Race to the Top. Ohio Report. Year 2: School Year 2011-2012. [State-Specific Summary Report

ERIC Educational Resources Information Center

US Department of Education, 2013

2013-01-01

This State-specific summary report serves as an assessment of Ohio's Year 2 Race to the Top implementation, highlighting successes and accomplishments, identifying challenges, and providing lessons learned from implementation from approximately September 2011 through September 2012. During Year 2, Ohio built on its Year 1 successes. In its…

How the built environment affects physical activity: views from urban planning.

PubMed

Handy, Susan L; Boarnet, Marlon G; Ewing, Reid; Killingsworth, Richard E

2002-08-01

The link between the built environment and human behavior has long been of interest to the field of urban planning, but direct assessments of the links between the built environment and physical activity as it influences personal health are still rare in the field. Yet the concepts, theories, and methods used by urban planners provide a foundation for an emerging body of research on the relationship between the built environment and physical activity. Recent research efforts in urban planning have focused on the idea that land use and design policies can be used to increase transit use as well as walking and bicycling. The development of appropriate measures for the built environment and for travel behavior is an essential element of this research. The link between the built environment and travel behavior is then made using theoretical frameworks borrowed from economics, and in particular, the concept of travel as a derived demand. The available evidence lends itself to the argument that a combination of urban design, land use patterns, and transportation systems that promotes walking and bicycling will help create active, healthier, and more livable communities. To provide more conclusive evidence, however, researchers must address the following issues: An alternative to the derived-demand framework must be developed for walking, measures of the built environment must be refined, and more-complete data on walking must be developed. In addition, detailed data on the built environment must be spatially matched to detailed data on travel behavior.

The Dark Side:Stigma in purpose-built senior environments

PubMed Central

Hrybyk, G; Rubinstein, RL; Eckert, K; Frankowski, AC; Keimig, L; Nemec, M; Peeples, A; Roth, E; Doyle, PJ

2014-01-01

This paper focuses on stigma in collective living environments for older adults, specifically multi-level campuses. We contrast two design profiles, a purpose-built campus which opened in 1997, and an older setting that grew by accretion over decades. Purpose-built housing is used as originally intended, designed, and constructed; housing built by accretion has been modified over time to meet changing needs and uses. The separation by care levels in both sites is reflected in their cultures as residents and staff relate to physical levels of care through a vocabulary of fear and stigma. Residents of the independent living building on the purpose-built campus refer to the assisted living building, accessed only through a second floor link, as “the other side” or “the dark side.” In this setting we observe stigma assigned to a place in the built environment. By contrast, in the older setting built by accretion over the last century, levels of care feature a less-structured clustering of independent living and assisted living, and common areas were shared by residents from multiple care levels. We have observed less stigma associated with levels of care in this older building. Grounding our analysis in data drawn from ongoing ethnographic research, we focus on the built environment as it relates to stigma in the social environment. The paper concludes with a discussion of the importance and pervasiveness of stigma in senior environments. PMID:25214701

Optimization of Second Fault Detection Thresholds to Maximize Mission POS

NASA Technical Reports Server (NTRS)

Anzalone, Evan

2018-01-01

In order to support manned spaceflight safety requirements, the Space Launch System (SLS) has defined program-level requirements for key systems to ensure successful operation under single fault conditions. To accommodate this with regards to Navigation, the SLS utilizes an internally redundant Inertial Navigation System (INS) with built-in capability to detect, isolate, and recover from first failure conditions and still maintain adherence to performance requirements. The unit utilizes multiple hardware- and software-level techniques to enable detection, isolation, and recovery from these events in terms of its built-in Fault Detection, Isolation, and Recovery (FDIR) algorithms. Successful operation is defined in terms of sufficient navigation accuracy at insertion while operating under worst case single sensor outages (gyroscope and accelerometer faults at launch). In addition to first fault detection and recovery, the SLS program has also levied requirements relating to the capability of the INS to detect a second fault, tracking any unacceptable uncertainty in knowledge of the vehicle's state. This detection functionality is required in order to feed abort analysis and ensure crew safety. Increases in navigation state error and sensor faults can drive the vehicle outside of its operational as-designed environments and outside of its performance envelope causing loss of mission, or worse, loss of crew. The criteria for operation under second faults allows for a larger set of achievable missions in terms of potential fault conditions, due to the INS operating at the edge of its capability. As this performance is defined and controlled at the vehicle level, it allows for the use of system level margins to increase probability of mission success on the operational edges of the design space. Due to the implications of the vehicle response to abort conditions (such as a potentially failed INS), it is important to consider a wide range of failure scenarios in terms of both magnitude and time. As such, the Navigation team is taking advantage of the INS's capability to schedule and change fault detection thresholds in flight. These values are optimized along a nominal trajectory in order to maximize probability of mission success, and reducing the probability of false positives (defined as when the INS would report a second fault condition resulting in loss of mission, but the vehicle would still meet insertion requirements within system-level margins). This paper will describe an optimization approach using Genetic Algorithms to tune the threshold parameters to maximize vehicle resilience to second fault events as a function of potential fault magnitude and time of fault over an ascent mission profile. The analysis approach, and performance assessment of the results will be presented to demonstrate the applicability of this process to second fault detection to maximize mission probability of success.

Design and Demonstration of a Miniature Lidar System for Rover Applications

NASA Technical Reports Server (NTRS)

Robinson, Benjamin

2010-01-01

A basic small and portable lidar system for rover applications has been designed. It uses a 20 Hz Nd:YAG pulsed laser, a 4-inch diameter telescope receiver, a custom-built power distribution unit (PDU), and a custom-built 532 nm photomultiplier tube (PMT) to measure the lidar signal. The receiving optics have been designed, but not constructed yet. LabVIEW and MATLAB programs have also been written to control the system, acquire data, and analyze data. The proposed system design, along with some measurements, is described. Future work to be completed is also discussed.

Tank Monitoring and Document control System (TMACS) As Built Software Design Document

DOE Office of Scientific and Technical Information (OSTI.GOV)

GLASSCOCK, J.A.

This document describes the software design for the Tank Monitor and Control System (TMACS). This document captures the existing as-built design of TMACS as of November 1999. It will be used as a reference document to the system maintainers who will be maintaining and modifying the TMACS functions as necessary. The heart of the TMACS system is the ''point-processing'' functionality where a sample value is received from the field sensors and the value is analyzed, logged, or alarmed as required. This Software Design Document focuses on the point-processing functions.

Single-molecule fluorescence study of the inhibition of the oncogenic functionality of STAT3

NASA Astrophysics Data System (ADS)

Liu, Baoxu; Badali, Daniel; Fletcher, Steven; Avadisian, Miriam; Gunning, Patrick; Gradinaru, Claudiu

2009-06-01

Signal-Transducer-and-Activator-of-Transcription 3 (STAT3) protein plays an important role in the onset of cancers such as leukemia and lymphoma. In this study, we aim to test the effectiveness of a novel peptide drug designed to tether STAT3 to the phospholipid bilayer of the cell membrane and thus inhibit unwanted transcription. As a first step, STAT3 proteins were successfully labelled with tetramethylrhodamine (TMR), a fluorescent dye with suitable photostability for single molecule studies. The effectiveness of labelling was determined using fluorescence correlation spectroscopy in a custom built confocal microscope, from which diffusion times and hydrodynamic radii of individual proteins were determined. A newly developed fluorescein derivative label (F-NAc) has been designed to be incorporated into the structure of the peptide drug so that peptide-STAT3 interactions can be examined. This dye is spectrally characterized and is found to be well suited for its application to this project, as well as other single-molecule studies. The membrane localization via high-affinity cholesterol-bound small-molecule binding agents can be demonstrated by encapsulating TMR-labeled STAT3 and inhibitors within a vesicle model cell system. To this end, unilaminar lipid vesicles were examined for size and encapsulation ability. Preliminary results of the efficiency and stability of the STAT3 anchoring in lipid membranes obtained via quantitative confocal imaging and single-molecule spectroscopy using a custom-built multiparameter fluorescence microscope are reported here.

IPv6 and IPsec Tests of a Space-Based Asset, the Cisco Router in Low Earth Orbit (CLEO)

NASA Technical Reports Server (NTRS)

Ivancic, William; Stewart, David; Wood, Lloyd; Jackson, Chris; Northam, James; Wilhelm, James

2008-01-01

This report documents the design of network infrastructure to support testing and demonstrating network-centric operations and command and control of space-based assets, using IPv6 and IPsec. These tests were performed using the Cisco router in Low Earth Orbit (CLEO), an experimental payload onboard the United Kingdom--Disaster Monitoring Constellation (UK-DMC) satellite built and operated by Surrey Satellite Technology Ltd (SSTL). On Thursday, 29 March 2007, NASA Glenn Research Center, Cisco Systems and SSTL performed the first configuration and demonstration of IPsec and IPv6 onboard a satellite in low Earth orbit. IPv6 is the next generation of the Internet Protocol (IP), designed to improve on the popular IPv4 that built the Internet, while IPsec is the protocol used to secure communication across IP networks. This demonstration was made possible in part by NASA s Earth Science Technology Office (ESTO) and shows that new commercial technologies such as mobile networking, IPv6 and IPsec can be used for commercial, military and government space applications. This has direct application to NASA s Vision for Space Exploration. The success of CLEO has paved the way for new spacebased Internet technologies, such as the planned Internet Routing In Space (IRIS) payload at geostationary orbit, which will be a U.S. Department of Defense Joint Capability Technology Demonstration. This is a sanitized report for public distribution. All real addressing has been changed to psueco addressing.

Design and implementation of a physical activity intervention to enhance children's use of the built environment (the CUBE study).

PubMed

Oreskovic, Nicolas M; Goodman, Elizabeth; Park, Elyse R; Robinson, Alyssa I; Winickoff, Jonathan P

2015-01-01

Adequate physical activity promotes physical and mental health and decreases obesity risk. However, most adolescents do not attain recommended physical activity levels and effective interventions are lacking. Physical activity trials rarely incorporate built environment use patterns. This paper describes the design and rationale of the Children's Use of the Built Environment (CUBE) Study, an office-based intervention designed to teach youth how to use their surrounding built environment to increase physical activity. CUBE is a 6-month intervention trial among 60 overweight and obese 10-16 year old adolescents from a community health center in Massachusetts. The study began in the winter of 2013. Patients are sequentially assigned to either the intervention or control group. Baseline physical activity by accelerometry and location by GPS, along with measured height, weight, and blood pressure are collected. Control subjects receive standard of care lifestyle counseling. Intervention subjects receive tailored recommendations on how to increase their physical activity based on their accelerometer and GPS data. Data collections are repeated at end-of-treatment, and again 3 months later. The findings from this study should help guide future efforts to design interventions aimed at increasing adolescent physical activity as well as to inform design professionals and government officials charged with creating outdoor spaces where adolescents spend time. Copyright © 2014 Elsevier Inc. All rights reserved.

Video Teleconferencing in the Compounding Laboratory Component of a Dual-Campus Doctor of Pharmacy Program

PubMed Central

Shrewsbury, Robert P.

2011-01-01

Objectives. To design, implement, and assess the effectiveness of using a live video teleconferencing system to connect the main campus and a satellite campus during laboratory compounding exercises in a doctor of pharmacy (PharmD) program. Design. A new laboratory facility with identical equipment and supplies to the main campus was built at the satellite campus and teleconferencing equipment was set up. Students on both campuses prepared 20 compounded formulations over a 5-course pharmaceutical care laboratory sequence. Live video teleconferencing was used for students to ask questions and for the lead faculty instructor to observe the students’ technique. Faculty and staff members and teaching assistants facilitated the laboratory sessions on both campuses. Assessment. The performance of students on assayed products at the main campus was compared with that of students at the satellite campus to ensure program integrity with the compounding laboratory component. The use of video teleconferencing for teaching compounding was successful and no difference in overall student pass rates was seen. The few observed differences in student performance between the 2 campuses were believed to be a result of variations in instructor communication with distant students. Conclusion. Video teleconferencing can be used successfully to deliver curriculum in laboratory compounding to pharmacy students. PMID:22171109

1. General view of west elevation of Chapel, built 192830 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. General view of west elevation of Chapel, built 1928-30 according to designs by ABMC Consulting Architect Paul P. Cret. - Flanders Field American Cemetery & Memorial, Chapel, Wortegemseweg 117, Waregem, West Flanders (Belgium), BEL

A fuel cell balance of plant test facility

NASA Astrophysics Data System (ADS)

Dicks, A. L.; Martin, P. A.

Much attention is focused in the fuel cell community on the development of reliable stack technology, but to successfully exploit fuel cells, they must form part of integrated power generation systems. No universal test facilities exist to evaluate SOFC stacks and comparatively little research has been undertaken concerning the issues of the rest of the system, or balance of plant (BOP). BG, in collaboration with Eniricerche, has therefore recently designed and built a test facility to evaluate different configurations of the BOP equipment for a 1-5 kWe solid oxide fuel cell (SOFC) stack. Within this BOP project, integrated, dynamic models have been developed. These have shown that three characteristic response times exist when the stack load is changed and that three independent control loops are required to manage the almost instantaneous change in power output from an SOFC stack, maintain the fuel utilisation and control the stack temperature. Control strategies and plant simplifications, arising from the dynamic modelling, have also been implemented in the BOP test facility. An SOFC simulator was designed and integrated into the control system of the test rig to behave as a real SOFC stack, allowing the development of control strategies without the need for a real stack. A novel combustor has been specifically designed, built and demonstrated to be capable of burning the low calorific anode exhaust gas from an SOFC using the oxygen depleted cathode stream. High temperature, low cost, shell and tube heat exchangers have been shown to be suitable for SOFC systems. Sealing of high temperature anode recirculation fans has, however, been shown to be a major issue and identified as a key area for further investigation.

UNH Project SMART 2017: Space Science for High School Students

NASA Astrophysics Data System (ADS)

Smith, C. W.; Broad, L.; Goelzer, S.; Levergood, R.; Lugaz, N.; Moebius, E.

2017-12-01

Every summer for the past 26 years the University of New Hampshire (UNH) has run a month-long, residential outreach program for high school students considering careers in mathematics, science, or engineering. Space science is one of the modules. Students work directly with UNH faculty performing original work with real spacecraft data and hardware and present the results of that effort at the end of the program. This year the student research projects used data from the Messenger, STEREO, and Triana missions. In addition, the students build and fly a high-altitude balloon payload with instruments of their own construction. Students learn circuit design and construction, microcontroller programming, and core atmospheric and space science along with fundamental concepts in space physics and engineering. Our payload design has evolved significantly since the first flight of a simple rectangular box and now involves a stable descent vehicle that does not require a parachute. Our flight hardware includes an on-board flight control computer, in-flight autonomous control and data acquisition of multiple student-built instruments, and real-time camera images sent to ground. This year we developed, built and flew a successful line cutter based on GPS location information that prevents our payload from falling into the ocean while also separating the payload from the balloon remains for a cleaner descent. We will describe that new line cutter design and implementation along with the shielded Geiger counters that we flew as part of our cosmic ray air shower experiment. This is a program that can be used as a model for other schools to follow and that high schools can initiate. More information can be found at .

The first object oriented monitor for intravenous anesthesia.

PubMed

Cantraine, F R; Coussaert, E J

2000-01-01

To describe the design and implementation of "INFUSION TOOLBOX," a software tool to control and monitor multiple intravenous drug infusions simultaneously using pharmacokinetic and pharmacodynamic principles. INFUSION TOOLBOX has been designed to present a graphical interface. Object Oriented design was used and the software was implemented using Smalltalk, to run on a PC. Basic tools are available to manage patient, drugs, pumps and reports. These tools are the PatientPanel, the DrugPanel, the PumpPanel and the HistoryPanel. The screen is built dynamically. The panels may be collapsed or closed to avoid a crowded display. We also built control panels such as the Target ControlPanel which calculates the best infusion sequence to bring the drug concentration in the plasma compartment to a preset value. Before drug delivery, the user enters the patient's data, selects a drug, enters its dilution factor and chooses a pharmacokinetic model. The calculated plasma concentration is continually displayed and updated. The anesthetist may ask for the history of the delivery to obtain a graphic report or to add events to the logbook. A panel targeting the effect is used when a pharmacodynamic model is known. Data files for drugs, pumps and surgery are upgradable. By creating a resizeable ControlPanel we enable the anesthetist to display the information he wishes, when he wishes it. The available panels are diverse enough to meet the anesthetist needs; they may be adapted to the drug used, pumps used and surgery. It is the anesthetist who builds dynamically its different control screens. By adopting an evolutionary solution model we have achieved considerable success in building our drug delivery monitor. In addition we have gained valuable insight into the anesthesia information domain that will allow us to further enhance and expand the system.

Phoenix Lidar Operation Animation

NASA Image and Video Library

2008-05-29

This image from NASA Phoenix Mars Lander of the Canadian-built meteorological station lidar, which was successfully activated on Sol 2 by first opening its dust cover, then emitting rapid pulses of light.

Surrogate Poster Artist Concept

NASA Image and Video Library

2015-03-11

This artist's concept shows Surrogate, a robot that could one day assist in disasters or hazardous situations such as a dangerous chemical laboratory. Surrogate was designed and built at the Jet Propulsion Laboratory in Pasadena, California. Its components came from RoboSimian, another JPL-built robot designed for disaster relief and mitigation (see PIA19313). Surrogate rolls on a track rather than moving on its limbs. http://photojournal.jpl.nasa.gov/catalog/PIA19314

Design of an air ejector for boundary-layer bleed of an acoustically treated turbofan engine inlet during ground testing

NASA Technical Reports Server (NTRS)

Stakolich, E. G.

1978-01-01

An air ejector was designed and built to remove the boundary-layer air from the inlet a turbofan engine during an acoustic ground test program. This report describes; (1) how the ejector was sized; (2) how the ejector performed; and (3) the performance of a scale model ejector built and tested to verify the design. With proper acoustic insulation, the ejector was effective in reducing boundary layer thickness in the inlet of the turbofan engine while obtaining the desired acoustic test conditions.

Successful rehabilitation program rests on service utilization.

PubMed

Lane, L

1993-07-01

An effective rehabilitation strategy is built upon three fundamentals: translating resident needs into delivered services, managing occupancy and marketing programs, and utilizing existing reimbursement mechanisms to ensure profitability of the venture.

Software for Secondary-School Learning About Robotics

NASA Technical Reports Server (NTRS)

Shelton, Robert O.; Smith, Stephanie L.; Truong, Dat; Hodgson, Terry R.

2005-01-01

The ROVer Ranch is an interactive computer program designed to help secondary-school students learn about space-program robotics and related basic scientific concepts by involving the students in simplified design and programming tasks that exercise skills in mathematics and science. The tasks involve building simulated robots and then observing how they behave. The program furnishes (1) programming tools that a student can use to assemble and program a simulated robot and (2) a virtual three-dimensional mission simulator for testing the robot. First, the ROVer Ranch presents fundamental information about robotics, mission goals, and facts about the mission environment. On the basis of this information, and using the aforementioned tools, the student assembles a robot by selecting parts from such subsystems as propulsion, navigation, and scientific tools, the student builds a simulated robot to accomplish its mission. Once the robot is built, it is programmed and then placed in a three-dimensional simulated environment. Success or failure in the simulation depends on the planning and design of the robot. Data and results of the mission are available in a summary log once the mission is concluded.

Flight Test of the F/A-18 Active Aeroelastic Wing Airplane

NASA Technical Reports Server (NTRS)

Clarke, Robert; Allen, Michael J.; Dibley, Ryan P.; Gera, Joseph; Hodgkinson, John

2005-01-01

Successful flight-testing of the Active Aeroelastic Wing airplane was completed in March 2005. This program, which started in 1996, was a joint activity sponsored by NASA, Air Force Research Laboratory, and industry contractors. The test program contained two flight test phases conducted in early 2003 and early 2005. During the first phase of flight test, aerodynamic models and load models of the wing control surfaces and wing structure were developed. Design teams built new research control laws for the Active Aeroelastic Wing airplane using these flight-validated models; and throughout the final phase of flight test, these new control laws were demonstrated. The control laws were designed to optimize strategies for moving the wing control surfaces to maximize roll rates in the transonic and supersonic flight regimes. Control surface hinge moments and wing loads were constrained to remain within hydraulic and load limits. This paper describes briefly the flight control system architecture as well as the design approach used by Active Aeroelastic Wing project engineers to develop flight control system gains. Additionally, this paper presents flight test techniques and comparison between flight test results and predictions.

The Astro-H Soft X-Ray Mirror

NASA Technical Reports Server (NTRS)

Robinson, David; Okajima, Takashi; Serlemitsos, Peter; Soong, Yang

2012-01-01

The Astro-H is led by the Japanese Space Agency (JAXA) in collaboration with many other institutions including the NASA Goddard Space Flight Center. Goddard's contributions include two soft X-ray telescopes (SXTs). The telescopes have an effective area of 562 square cm at 1 keV and 425 square cm at 6 keV with an image quality requirement of 1.7 arc-minutes half power diameter (HPD). The engineering model has demonstrated 1.1 arc-minutes HPD error. The design of the SXT is based on the successful Suzaku mission mirrors with some enhancements to improve the image quality. Two major enhancements are bonding the X-ray mirror foils to alignment bars instead of allowing the mirrors to float, and fabricating alignment bars with grooves within 5 microns of accuracy. An engineering model SXT was recently built and subjected to several tests including vibration, thermal, and X-ray performance in a beamline. Several lessons were learned during this testing that will be incorporated in the flight design. Test results and optical performance are discussed, along with a description of the design of the SXT.

Designing and Evaluating Interventions to Halt the Transmission of Tuberculosis.

PubMed

Dowdy, David W; Grant, Alison D; Dheda, Keertan; Nardell, Edward; Fielding, Katherine; Moore, David A J

2017-11-03

To reduce the incidence of tuberculosis, it is insufficient to simply understand the dynamics of tuberculosis transmission. Rather, we must design and rigorously evaluate interventions to halt transmission, prioritizing those interventions most likely to achieve population-level impact. Synergy in reducing tuberculosis transmission may be attainable by combining interventions that shrink the reservoir of latent Mycobacterium tuberculosis infection (preventive therapy), shorten the time between disease onset and treatment initiation (case finding and diagnosis), and prevent transmission in key settings, such as the built environment (infection control). In evaluating efficacy and estimating population-level impact, cluster-randomized trials and mechanistic models play particularly prominent roles. Historical and contemporary evidence suggests that effective public health interventions can halt tuberculosis transmission, but an evidence-based approach based on knowledge of local epidemiology is necessary for success. We provide a roadmap for designing, evaluating, and modeling interventions to interrupt the process of transmission that fuels a diverse array of tuberculosis epidemics worldwide. © The Author 2017. Published by Oxford University Press for the Infectious Diseases Society of America.

Triboelectric Nanogenerator as a Self-Powered Communication Unit for Processing and Transmitting Information.

PubMed

Yu, Aifang; Chen, Xiangyu; Wang, Rui; Liu, Jingyu; Luo, Jianjun; Chen, Libo; Zhang, Yang; Wu, Wei; Liu, Caihong; Yuan, Hongtao; Peng, Mingzeng; Hu, Weiguo; Zhai, Junyi; Wang, Zhong Lin

2016-04-26

In this paper, we demonstrate an application of a triboelectric nanogenerator (TENG) as a self-powered communication unit. An elaborately designed TENG is used to translate a series of environmental triggering signals into binary digital signals and drives an electronic-optical device to transmit binary digital data in real-time without an external power supply. The elaborately designed TENG is built in a membrane structure that can effectively drive the electronic-optical device in a bandwidth from 1.30 to 1.65 kHz. Two typical communication modes (amplitude-shift keying and frequency-shift keying) are realized through the resonant response of TENG to different frequencies, and two digital signals, i.e., "1001" and "0110", are successfully transmitted and received through this system, respectively. Hence, in this study, a simple but efficient method for directly transmitting ambient vibration to the receiver as a digital signal is established using an elaborately designed TENG and an optical communication technique. This type of the communication system, as well as the implementation method presented, exhibits great potential for applications in the smart city, smart home, password authentication, and so on.

The Influence of Weather Variation, Urban Design and Built Environment on Objectively Measured Sedentary Behaviour in Children

PubMed Central

Katapally, Tarun Reddy; Rainham, Daniel; Muhajarine, Nazeem

2016-01-01

With emerging evidence indicating that independent of physical activity, sedentary behaviour (SB) can be detrimental to health, researchers are increasingly aiming to understand the influence of multiple contexts such as urban design and built environment on SB. However, weather variation, a factor that continuously interacts with all other environmental variables, has been consistently underexplored. This study investigated the influence of diverse environmental exposures (including weather variation, urban design and built environment) on SB in children. This cross-sectional observational study is part of an active living research initiative set in the Canadian prairie city of Saskatoon. Saskatoon's neighbourhoods were classified based on urban street design into grid-pattern, fractured grid-pattern and curvilinear types of neighbourhoods. Diverse environmental exposures were measured including, neighbourhood built environment, and neighbourhood and household socioeconomic environment. Actical accelerometers were deployed between April and June 2010 (spring-summer) to derive SB of 331 10–14 year old children in 25 one week cycles. Each cycle of accelerometry was conducted on a different cohort of children within the total sample. Accelerometer data were matched with localized weather patterns derived from Environment Canada weather data. Multilevel modeling using Hierarchical Linear and Non-linear Modeling software was conducted by factoring in weather variation to depict the influence of diverse environmental exposures on SB. Both weather variation and urban design played a significant role in SB. After factoring in weather variation, it was observed that children living in grid-pattern neighbourhoods closer to the city centre (with higher diversity of destinations) were less likely to be sedentary. This study demonstrates a methodology that could be replicated to integrate geography-specific weather patterns with existing cross-sectional accelerometry data to understand the influence of urban design and built environment on SB in children. PMID:29546188

Design Methodology of a Dual-Halbach Array Linear Actuator with Thermal-Electromagnetic Coupling

PubMed Central

Eckert, Paulo Roberto; Flores Filho, Aly Ferreira; Perondi, Eduardo; Ferri, Jeferson; Goltz, Evandro

2016-01-01

This paper proposes a design methodology for linear actuators, considering thermal and electromagnetic coupling with geometrical and temperature constraints, that maximizes force density and minimizes force ripple. The method allows defining an actuator for given specifications in a step-by-step way so that requirements are met and the temperature within the device is maintained under or equal to its maximum allowed for continuous operation. According to the proposed method, the electromagnetic and thermal models are built with quasi-static parametric finite element models. The methodology was successfully applied to the design of a linear cylindrical actuator with a dual quasi-Halbach array of permanent magnets and a moving-coil. The actuator can produce an axial force of 120 N and a stroke of 80 mm. The paper also presents a comparative analysis between results obtained considering only an electromagnetic model and the thermal-electromagnetic coupled model. This comparison shows that the final designs for both cases differ significantly, especially regarding its active volume and its electrical and magnetic loading. Although in this paper the methodology was employed to design a specific actuator, its structure can be used to design a wide range of linear devices if the parametric models are adjusted for each particular actuator. PMID:26978370

Bioarchitecture - a new vision of energy sustainable cities

NASA Astrophysics Data System (ADS)

Krzemińska, Alicja; Zaręba, Anna; Dzikowska, Anna

2017-11-01

Transformation of the natural environment will press the humanity to search for the new look at the problems of architecture and urban design. Nowadays passive houses construction is a standard and green roofs are incorporated in the design of contemporary cities. That's why city cluster will be successively transformed into sustainable bionic systems, which allows to protect the nature and stop further degradation and exploitation of public green space. The good examples of contemporary trend of designing in harmony with nature are energy sustainable underground buildings of Malcolm Wells, who in 60s designed his first energy sufficient construction. The underground cities and rock houses were built from the early beginning of architecture, with significant examples of cities: Sanmenxia in China in Henan Province, Matmata (Tunisia), Cappadocia (Turkey), Uplisciche (Georgia) or Brlhovce (Slovakia) etc. The underground buildings and cities, blending in with the background of topography, have a positive influence on the landscape and are energy sustainable. Climate responsive design materials create effective insulation, which allows to maintain the stable temperature inside the buildings. Bioarchitecture improves the microclimate in the neighborhood through increasing oxygen concentration in atmosphere and limiting of CO2 emission. Bioarchitecture represents new direction in changing the design priorities towards being closer with nature and it's needs.

Design Methodology of a Dual-Halbach Array Linear Actuator with Thermal-Electromagnetic Coupling.

PubMed

Eckert, Paulo Roberto; Flores Filho, Aly Ferreira; Perondi, Eduardo; Ferri, Jeferson; Goltz, Evandro

2016-03-11

This paper proposes a design methodology for linear actuators, considering thermal and electromagnetic coupling with geometrical and temperature constraints, that maximizes force density and minimizes force ripple. The method allows defining an actuator for given specifications in a step-by-step way so that requirements are met and the temperature within the device is maintained under or equal to its maximum allowed for continuous operation. According to the proposed method, the electromagnetic and thermal models are built with quasi-static parametric finite element models. The methodology was successfully applied to the design of a linear cylindrical actuator with a dual quasi-Halbach array of permanent magnets and a moving-coil. The actuator can produce an axial force of 120 N and a stroke of 80 mm. The paper also presents a comparative analysis between results obtained considering only an electromagnetic model and the thermal-electromagnetic coupled model. This comparison shows that the final designs for both cases differ significantly, especially regarding its active volume and its electrical and magnetic loading. Although in this paper the methodology was employed to design a specific actuator, its structure can be used to design a wide range of linear devices if the parametric models are adjusted for each particular actuator.

The Space-Age Legacy of Telescope Designer George A. Carroll

NASA Astrophysics Data System (ADS)

Briggs, John W.

2013-01-01

Remembered particularly as a founding member of Stony Ridge Observatory near Mount Wilson, George A. Carroll (1902-1987) was legendary in the Southern California telescope making community. In Texas at the age of sixteen, Carroll built and flew his own aircraft, becoming one of the youngest aviators in the country. He eventually became an employee of Lockheed's "Skunk Works" in Burbank. His earliest known commercial telescopes were high-end amateur instruments built by R. R. Cook. As described in a brochure describing his later telescope work, he had "experience in so many branches of technology that it is unbelievable." By the time Carroll's designs were built by Thomas Tool & Die in Sun Valley, his telescopes were well known in the solar community and in use at National Solar Observatory, Caltech, and at many other domestic and international research institutions. Among the most remarkable were large solar spars for Lockheed Solar Observatory in California and Ottawa River Solar Observatory in Canada. His instrumentation also equipped educational facilities including observatories at UCLA, Westmont College, Pasadena City College, Bevard Community College, and many others. A Carroll telescope boasting a particularly distinguished educational history was a small astrograph built in 1953 for Professor George Moyen of Hollywood and subsequently used for the long-running Summer Science Program in Ojai, California. Later solar instruments built by Carson Instruments were closely derivative of Carroll designs.

Toward more robust projections of forest landscape dynamics under novel environmental conditions: embedding PnET within LANDIS-II

Treesearch

A. De Bruijn; E.J. Gustafson; B.R. Sturtevant; J.R. Foster; B.R. Miranda; N.I. Lichti; D.F. Jacobs

2014-01-01

Ecological models built on phenomenological relationships and behavior of the past may not be robustunder novel conditions of the future because global changes are producing environmental conditions that forests have not experienced historically. We developed a new succession extension for the LANDIS-II forest landscape model, PnET-Succession, to simulate forest growth...

Ultra Small Aperture Terminal: System Design and Test Results

NASA Technical Reports Server (NTRS)

Sohn, Philip Y.; Reinhart, Richard C.

1996-01-01

The Ultra Small Aperture Terminal (USAT) has been developed to test and demonstrate remote and broadcast satcom applications via the Advanced Communications Technology Satellite (ACTS). The design of these ground stations emphasize small size, low power consumption, portable and rugged terminals. Each ground station includes several custom design parts such as 35 cm diameter antenna, 1/4 Watt transmitter with built-in upconverter, and 4.0 dB Noise Figure (NF) receiver with built-in downconverter. In addition, state-of-the-art commercial parts such as highly stable ovenized crystal oscillators and dielectric resonator oscillators are used in the ground station design. Presented in this paper are system level design description, performance, and sample applications.

Beam director design report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Younger, F.C.

1986-08-01

A design and fabrication effort for a beam director is documented. The conceptual design provides for the beam to pass first through a bending and focusing system (or ''achromat''), through a second achromat, through an air-to-vacuum interface (the ''beam window''), and finally through the vernier steering system. Following an initial concept study for a beam director, a prototype permanent magnet 30/sup 0/ beam-bending achromat and prototype vernier steering magnet were designed and built. In volume II, copies are included of the funding instruments, requests for quotations, purchase orders, a complete set of as-built drawings, magnetic measurement reports, the concept designmore » report, and the final report on the design and fabrication project. (LEW)« less

WE-D-BRE-01: A Sr-90 Irradiation Device for the Study of Cutaneous Radiation Injury

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorand, JE; Bourland, JD; Burnett, LR

2014-06-15

Purpose: To determine dosimetric character for a custom-built Sr-90 beta irradiator designed for the study of Cutaneous Radiation Injury (CRI) in a porcine animal model. In the event of a radiological accident or terrorist event, Sr-90, a fission by-product, will likely be produced. CRI is a main concern due to the low energy and superficial penetration in tissue of beta particles from Sr-90. Seven 100 mCi plaque Sr-90 radiation sources within a custom-built irradiation device create a 40 mm diameter region of radiation-induced skin injury as part of a larger project to study the efficacy of a topical keratin-based productmore » in CRI healing. Methods: A custom-built mobile irradiation device was designed and implemented for in vivo irradiations. Gafchromic™ EBT3 radiochromic film and a PTW Markus chamber type 23343 were utilized for dosimetric characterization of the beta fluence at the surface produced by this device. Films were used to assess 2-dimensional dose distribution and percent depth dose characteristics of the radiation field. Ion chamber measurements provided dose rate data within the field. Results: The radiation field produced by the irradiation device is homogeneous with high uniformity (∼5%) and symmetry (∼3%) with a steep dose fall-off with depth from the surface. Dose rates were determined to be 3.8 Gy/min and 3.3 Gy/min for film and ion chamber measurements, respectively. A dose rate of 3.4 Gy/min was used to calculate irradiation times for in vivo irradiations. Conclusion: The custom-built irradiation device enables the use of seven Sr-90 beta sources in an array to deliver a 40 mm diameter area of homogeneous skin dose with a dose rate that is useful for research purposes and clinically relevant for the induction of CRI. Doses of 36 and 42 Gy successfully produce Grade III CRI and are used in the study of the efficacy of KeraStat™. This project has been funded in whole or in part with Federal funds from the Biomedical Advanced Research and Development Authority, Office of the Assistant Secretary for Preparedness and Response, Office of the Secretary, Department of Health and Human Services, under Contract No. HHSO100201200007C.« less

Community mobility in the context of universal design: inter-professional collaboration and education.

PubMed

Hitch, Danielle; Larkin, Helen; Watchorn, Valerie; Ang, Susan

2012-10-01

The design of built environments is a critical factor in facilitating participation for all community members. This study aimed to explore key stakeholders' views on the role and collaboration of occupational therapists and architects in relation to universal design and the built environment. This study is currently the only research to focus on the needs and practices of both occupational therapy and architecture in universal design. The results have implications for both clinical practice and professional education, and highlight an area of developing interest in occupational therapy. Focus groups and semi-structured telephone interviews were conducted with key stakeholders involved in the design of built environments. Data from these interviews were analysed qualitatively, using codes of interpreted meaning which were then organised into themes. Three main themes emerged in relation to inter-professional collaboration around universal design: 'form vs. function', 'the earlier the better' and 'universal design as a specialist area'. Although there are areas of synergy between occupational therapy and architecture in universal design, each profession has its own strengths and skills to bring to the design process. Given the multidisciplinary nature of ensuring designs support participation in occupations and roles, both professions could benefit from opportunities to meaningfully collaborate during professional education and in the workplace. © 2011 The Authors. Australian Occupational Therapy Journal © 2011 Occupational Therapy Australia.

First incremental buy for Increment 2 of the Space Transportation System (STS)

NASA Technical Reports Server (NTRS)

1989-01-01

Thiokol manufactured and delivered 9 flight motors to KSC on schedule. All test flights were successful. All spent SRMs were recovered. Design, development, manufacture, and delivery of required transportation, handling, and checkout equipment to MSFC and to KSC were completed on schedule. All items of data required by DPD 400 were prepared and delivered as directed. In the system requirements and analysis area, the point of departure from Buy 1 to the operational phase was developed in significant detail with a complete set of transition documentation available. The documentation prepared during the Buy 1 program was maintained and updated where required. The following flight support activities should be continued through other production programs: as-built materials usage tracking on all flight hardware; mass properties reporting for all flight hardware until sample size is large enough to verify that the weight limit requirements were met; ballistic predictions and postflight performance assessments for all production flights; and recovered SRM hardware inspection and anomaly identification. In the safety, reliability, and quality assurance area, activities accomplished were assurance oriented in nature and specifically formulated to prevent problems and hardware failures. The flight program to date has adequately demonstrated the success of this assurance approach. The attention focused on details of design, analysis, manufacture, and inspection to assure the production of high-quality hardware has resulted in the absence of flight failures. The few anomalies which did occur were evaluated, design or manufacturing changes incorporated, and corrective actions taken to preclude recurrence.

CATE: A Case Study of an Interdisciplinary Student-Led Microgravity Experiment

NASA Astrophysics Data System (ADS)

Colwell, J. E.; Dove, A.; Lane, S. S.; Tiller, C.; Whitaker, A.; Lai, K.; Hoover, B.; Benjamin, S.

2015-12-01

The Collisional Accretion Experiment (CATE) was designed, built, and flown on NASA's C-9 parabolic flight airplane in less than a year by an interdisciplinary team of 6 undergraduate students under the supervision of two faculty. CATE was selected in the initial NASA Undergraduate Student Instrument Project (USIP) solicitation in the Fall of 2013, and the experiment flight campaign was in July 2014. The experiment studied collisions between different particle populations at low velocities (sub-m/s) in a vacuum and microgravity to gain insight into processes in the protoplanetary disk and planetary ring systems. Faculty provided the experiment concept and key experiment design parameters, and the student team developed the detailed hardware design for all components, manufactured and tested hardware, operated the experiment in flight, and analyzed data post-flight. Students also developed and led an active social media campaign and education and public outreach campaign to engage local high school students in the project. The ability to follow an experiment through from conception to flight was a key benefit for undergraduate students whose available time for projects such as this is frequently limited to their junior and senior years. Key factors for success of the program included having an existing laboratory infrastructure and experience in developing flight payloads and an intrinsically simple experiment concept. Students were highly motivated, in part, by their sense of technical and scientific ownership of the project, and this engagement was key to the project's success.

The Lunar Crater Observation and Sensing Satellite (LCROSS) Payload Development and Performance in Flight

NASA Astrophysics Data System (ADS)

Ennico, Kimberly; Shirley, Mark; Colaprete, Anthony; Osetinsky, Leonid

2012-05-01

The primary objective of the Lunar Crater Observation and Sensing Satellite (LCROSS) was to confirm the presence or absence of water ice in a permanently shadowed region (PSR) at a lunar pole. LCROSS was classified as a NASA Class D mission. Its payload, the subject of this article, was designed, built, tested and operated to support a condensed schedule, risk tolerant mission approach, a new paradigm for NASA science missions. All nine science instruments, most of them ruggedized commercial-off-the-shelf (COTS), successfully collected data during all in-flight calibration campaigns, and most importantly, during the final descent to the lunar surface on October 9, 2009, after 112 days in space. LCROSS demonstrated that COTS instruments and designs with simple interfaces, can provide high-quality science at low-cost and in short development time frames. Building upfront into the payload design, flexibility, redundancy where possible even with the science measurement approach, and large margins, played important roles for this new type of payload. The environmental and calibration approach adopted by the LCROSS team, compared to existing standard programs, is discussed. The description, capabilities, calibration and in-flight performance of each instrument are summarized. Finally, this paper goes into depth about specific areas where the instruments worked differently than expected and how the flexibility of the payload team, the knowledge of instrument priority and science trades, and proactive margin maintenance, led to a successful science measurement by the LCROSS payload's instrument complement.

Exterior view, westsouthwest, of Jeudevine Memorial Library. Built 18961897 and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Exterior view, west-southwest, of Jeudevine Memorial Library. Built 1896-1897 and designed by local architect Lambert Packard, the library is an excellent example of Richardsonian Romanesque architecture. - Jeudevine Memorial Library, 93 North Main Street, Hardwick, Caledonia County, VT

Acoustic Resonance Spectroscopy (ARS) Munition Classification System enhancements. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vela, O.A.; Huggard, J.C.

Acoustic Resonance Spectroscopy (ARS) is a non-destructive evaluation technology developed at the Los Alamos National Laboratory (LANL). This technology has resulted in three generations of instrumentation, funded by the Defense Special Weapons Agency (DSWA), specifically designed for field identification of chemical weapon (CW) munitions. Each generation of ARS instrumentation was developed with a specific user in mind. The ARS1OO was built for use by the U.N. Inspection Teams going into Iraq immediately after the Persian Gulf War. The ARS200 was built for use in the US-Russia Bilateral Chemical Weapons Treaty (the primary users for this system are the US Onsitemore » Inspection Agency (OSIA) and their Russian counterparts). The ARS300 was built with the requirements of the Organization for the Prohibition of Chemical Weapons (OPCW) in mind. Each successive system is an improved version of the previous system based on learning the weaknesses of each and, coincidentally, on the fact that more time was available to do a requirements analysis and the necessary engineering development. The ARS300 is at a level of development that warrants transferring the technology to a commercial vendor. Since LANL will supply the computer software to the selected vendor, it is possible for LANL to continue to improve the decision algorithms, add features where necessary, and adjust the user interface before the final transfer occurs. This paper describes the current system, ARS system enhancements, and software enhancements. Appendices contain the Operations Manual (software Version 3.01), and two earlier reports on enhancements.« less

Voices of successful science teachers in an urban diverse single gender girls' school

NASA Astrophysics Data System (ADS)

Malhan, Jyoti

This research study was conducted as a qualitative case study of four successful science teachers of female students in a diverse, title 1, urban, public girls' school. The study was designed to hear the 'muted' voices of successful science teachers concerning their beliefs and practices when they effectively provide learning opportunities for female students of color in their classrooms. Ethic of Care, equity pedagogy and culturally responsive pedagogy, created the theoretical framework for interpretation of the powerful narratives and storytelling that influenced this group of successful teachers. Data were collected by conducting in-depth, semi-structured interviews. Constant comparative method and narrative analysis were used to code and categorize the data. Analysis was conducted after each interview to discover emergent themes. Teachers conducted member checks throughout the process. The findings from the study yielded the following: (1) teachers had a passion for science and incorporated ongoing scientific developments and real-life examples and applications in their teaching, (2) teachers adopted a caring, concerned, and student-centered approach to teaching, (3) teachers acknowledged certain benefits to a single-sex girls education which included fewer distractions, increased confidence and comfort level of students, (5) teachers built relationships with students that encouraged students to engage with rigorous course content and meet higher expectations for performance. Themes that emerged included: care, culturally responsive pedagogy and culturally relevant curriculum.

Using the Science Process Skills to Investigate Animals and Animal Habitats

NASA Astrophysics Data System (ADS)

Braithwaite, Saisha

This study explored how a STEM (science, technology, engineering, and math) engineer design challenge allowed students to analyze the characteristics of animals and animal habitats. This study was conducted in a kindergarten class within an urban school district. The class has 25 students while the study focuses on six students. The group consists of three boys and three girls. In this study, the students used the science process skills to observe, classify, infer, and make predictions about animals and habitats. In the engineer design, students created an established habitat and built their own animal that can survive in that habitat. The study analyzed how students used process skills to engage with the habitats and animals. The students successfully used the science process skills in this study. The results showed that students gained more content knowledge when they used multiple process skills within a lesson. The study shows that developing lessons using the science process skills improves students' ability to demonstrate their knowledge of animals and their habitats.

Space Operation of the MOLA Laser

NASA Technical Reports Server (NTRS)

Afzal, Robert S.

2000-01-01

Interest in lasers for space applications such as active remote sensing in Earth orbit, planetary science, and inter-satellite laser communications is growing. These instruments typically use diode-pumped solid state lasers for the laser transmitter. The mission specifications and constraints of space qualification, place strict requirements on the design and operation of the laser. Although a laser can be built in the laboratory to meet performance specifications relatively routinely, tile mission constraints demand unique options and compromises in the materials used, and design to ensure the success of the mission. Presently, the best laser architecture for a light weight, rugged, high peak power and efficient transmitter is a diode laser pumped ND:YAG laser. Diode lasers can often obviate the need for water cooling, reduce the size and weight of the laser, increase the electrical to optical efficiency, system reliability, and lifetime. This paper describes the in-space operation and performance of the Mars Orbiter Laser Altimeter (MOLA) laser transmitter, representing the current state-of-the-art in space-based solid- state lasers.

Development of a 0.014-inch magnetic resonance imaging guidewire.

PubMed

Qiu, Bensheng; Karmarkar, Parag; Brushett, Chris; Gao, Fabao; Kon, Ryan; Kar, Sourav; Atalar, Ergin; Yang, Xiaoming

2005-04-01

The purpose of this study was to develop a standard 0.014-inch intravascular magnetic resonance imaging guidewire (MRIG), a coaxial cable with an extension of the inner conductor, specifically designed for use in the small vessels. After a theoretical analysis, the 0.014-inch MRIG was built by plating/cladding highly electrically conductive materials, silver or gold, over the inside and outside of the coaxial conductors. The conductors were made of superelastic, nonmagnetic, biocompatible materials, Nitinol or MP35N. Then, in comparison with a previously designed 0.032-inch MRIG, the performance of the new 0.014-inch MRIG in vitro and in vivo was successfully evaluated. This study represents the initial work to confirm the critical role of highly conductive and superelastic materials in building such small-size MRIGs, which are expected to generate high-resolution MR imaging of vessel walls/plaques and guide endovascular interventional procedures in the small vessels, such as the coronary arteries. Copyright 2005 Wiley-Liss, Inc.

Electromagnetic analysis of a superconducting transformer for high current characterization of cable in conduit conductors in background magnetic field

NASA Astrophysics Data System (ADS)

Wu, Xiangyang; Tan, Yunfei; Fang, Zhen; Jiang, Donghui; Chen, Zhiyou; Chen, Wenge; Kuang, Guangli

2017-10-01

A large cable-in-conduit-conductor (CICC) test facility has been designed and fabricated at the High Magnetic Field Laboratory of the Chinese Academy of Sciences (CHMFL) in order to meet the test requirement of the conductors which are applied to the future fusion reactor. The critical component of the test facility is an 80 kA superconducting transformer which consists of a multi-turn primary coil and a minor-turn secondary coil. As the current source of the conductor samples, the electromagnetic performance of the superconducting transformer determines the stability and safety of the test facility. In this paper, the key factors and parameters, which have much impact on the performance of the transformer, are analyzed in detail. The conceptual design and optimizing principles of the transformer are discussed. An Electromagnetic-Circuit coupled model built in ANSYS Multiphysics is successfully used to investigate the electromagnetic characterization of the transformer under the dynamic operation condition.

Shock tunnel studies of scramjet phenomena 1994

NASA Technical Reports Server (NTRS)

1995-01-01

A new expansion tube facility has been built, and is in the process of being commissioned. It has a bore of 90 mm, and has been designed for peak rupture pressures of 100 Mpa. It is configured with multiple sections and diaphragm location stations to give optimized performance over a range of sub and superorbital conditions. It has a compound piston arrangement for a two stage compression, designed to maximize the length of shock expansion tube which can be driven within a fixed total facility length. Experiments have been successfully performed with a dummy first stage piston, and a rubber energy absorbing brake. The results agree well with a one-dimensional stress wave model of the piston impacting on the rubber, and codes for piston motion. Strain of the rubber is restricted to approximately 20 percent at which level no damage is to be expected in the buffer material, and none has been observed, indicating that the mechanism will be fully reuseable.

Organism support for life sciences spacelab experiments

NASA Technical Reports Server (NTRS)

Drake, G. L.; Heppner, D. B.

1976-01-01

This paper presents an overview of the U.S. life sciences laboratory concepts envisioned for the Shuttle/Spacelab era. The basic development approach is to provide a general laboratory facility supplemented by specific experiment hardware as required. The laboratory concepts range from small carry-on laboratories to fully dedicated laboratories in the Spacelab pressurized module. The laboratories will encompass a broad spectrum of research in biology and biomedicine requiring a variety of research organisms. The environmental control and life support of these organisms is a very important aspect of the success of the space research missions. Engineering prototype organism habitats have been designed and fabricated to be compatible with the Spacelab environment and the experiment requirements. These first-generation habitat designs and their subsystems have supported plants, cells/tissues, invertebrates, and small vertebrates in limited evaluation tests. Special handling and transport equipment required for the ground movement of the experiment organisms at the launch/landing site have been built and tested using these initial habitat prototypes.

Measuring the impact of an API-first mentality with ScienceBase after 4.5 years

NASA Astrophysics Data System (ADS)

Bristol, S.; Tekell, S.

2016-12-01

ScienceBase is a research infrastructure developed and operated by the U.S. Geological Survey with users and uses across a number of other agency and organization partners. Over four years ago, we released an Application Programming Interface (API) as the foundation of the system and took on the mindset that our progress would be measured by the uptake of the API by others beyond ourselves in developing interesting applications. We now measure success more by someone finding ScienceBase, organizing their data and information, developing an innovative API-driven application and then serendipitous discovery through a science meeting. Because of the way we built the RESTful API, we can characterize what parts of the system are employed. Analysis of usage data helps us take the supposition out of what works and guides design and funding decisions. This analytics-based process facilitates regular adjustments to our thinking and allows us to test design decisions as hypotheses rather than untestable aspirations.

From Asteroids to Space Debris

NASA Astrophysics Data System (ADS)

Benkhaldoun, Zouhair; Moon, Hong-Kyu; Daassou, Ahmed; Park, Jang-Hyun; Lazrek, Mohamed

2016-01-01

Since 2011, Oukaimeden Observatory (OUCA) has become one of the active NEO search facilities in the word. Its discovery statistics shows that the MOSS (Morocco Oukaimeden Sky Survey) project received credits for more than 2,145 new designations, including 3 NEOs and 4 comets. Its excellent astro-climactic characteristics are partly behind the success. The average number of observable nights is around 280 nights per year, while median seeing is 0.8-0.9 arcsec. We completed construction of a new telescope at the site in March 2015. It is Optical Wide-field Patrol (OWL) facility designed and built by Korea Space Science Institute (KASI). The primary objective of this facility is to monitor national space assets of Korea; either wide-field imaging- or fast data acquisition- capabilities enable the 0.5m telescope to conduct observation programs to catalog and follow-up various transient events in the night sky. We present the seeing condition, the OWL system and preliminary results obtained at OWL@Oukaimeden during the past several months.

Future development of the PLATO Observatory for Antarctic science

NASA Astrophysics Data System (ADS)

Ashley, Michael C. B.; Bonner, Colin S.; Everett, Jon R.; Lawrence, Jon S.; Luong-Van, Daniel; McDaid, Scott; McLaren, Campbell; Storey, John W. V.

2010-07-01

PLATO is a self-contained robotic observatory built into two 10-foot shipping containers. It has been successfully deployed at Dome A on the Antarctic plateau since January 2008, and has accumulated over 730 days of uptime at the time of writing. PLATO provides 0.5{1kW of continuous electrical power for a year from diesel engines running on Jet-A1, supplemented during the summertime with solar panels. One of the 10-foot shipping containers houses the power system and fuel, the other provides a warm environment for instruments. Two Iridium satellite modems allow 45 MB/day of data to be transferred across the internet. Future enhancements to PLATO, currently in development, include a more modular design, using lithium iron-phosphate batteries, higher power output, and a light-weight low-power version for eld deployment from a Twin Otter aircraft. Technologies used in PLATO include a CAN (Controller Area Network) bus, high-reliability PC/104 com- puters, ultracapacitors for starting the engines, and fault-tolerant redundant design.

Renkioi: a forgotten Crimean War hospital and its significance.

PubMed

Silver, C P

2004-12-01

Renkioi Civil Hospital was built late in the Crimean War (1854-6) in Turkey on the Dardanelles. Designed by Isambard Kingdom Brunel, its prefabricated structure was a brilliant engineering innovation. As a civil hospital for military patients, it was staffed by experienced civilian doctors, thereby relieving the shortage of military doctors. Renkioi is remembered as an astonishing early prefabricated structure. However the war was soon to end and it was never used to near capacity. Thus, its other successful features are largely forgotten. It demonstrated the advantages of a doctors, rather than a military officer, being in complete command of a hospital and this was later accepted by the army. Renkioi also showed how infection could be reduced by able staff in a well administered, properly designed hospital with good sanitation. After the war, Dr. Edmund Parkes, its Medical Superintendent, became the first Professor of Hygiene at the new Army Medical School, ensuring that "the prevention of disease and the promotion of health" became the first function of the Army Medical Services.

Built-In Diagnostics (BID) Of Equipment/Systems

NASA Technical Reports Server (NTRS)

Granieri, Michael N.; Giordano, John P.; Nolan, Mary E.

1995-01-01

Diagnostician(TM)-on-Chip (DOC) technology identifies faults and commands systems reconfiguration. Smart microcontrollers operating in conjunction with other system-control circuits, command self-correcting system/equipment actions in real time. DOC microcontroller generates commands for associated built-in test equipment to stimulate unit of equipment diagnosed, collects and processes response data obtained by built-in test equipment, and performs diagnostic reasoning on response data, using diagnostic knowledge base derived from design data.

Conserving genomic variability in large mammals: Effect of population fluctuations and variance in male reproductive success on variability in Yellowstone bison

Treesearch

Andres Perez-Figueroa; Rick L. Wallen; Tiago Antao; Jason A. Coombs; Michael K. Schwartz; P. J. White; Gordon Luikart

2012-01-01

Loss of genetic variation through genetic drift can reduce population viability. However, relatively little is known about loss of variation caused by the combination of fluctuating population size and variance in reproductive success in age structured populations. We built an individual-based computer simulation model to examine how actual culling and hunting...

International Space Station External Contamination Environment for Space Science Utilization

NASA Technical Reports Server (NTRS)

Soares, Carlos E.; Mikatarian, Ronald R.; Steagall, Courtney A.; Huang, Alvin Y.; Koontz, Steven; Worthy, Erica

2014-01-01

The International Space Station (ISS) is the largest and most complex on-orbit platform for space science utilization in low Earth orbit. Multiple sites for external payloads, with exposure to the associated natural and induced environments, are available to support a variety of space science utilization objectives. Contamination is one of the induced environments that can impact performance, mission success and science utilization on the vehicle. The ISS has been designed, built and integrated with strict contamination requirements to provide low levels of induced contamination on external payload assets. This paper addresses the ISS induced contamination environment at attached payload sites, both at the requirements level as well as measurements made on returned hardware, and contamination forecasting maps being generated to support external payload topology studies and science utilization.

Design considerations and practical results with long duration systems for manned world flights

NASA Astrophysics Data System (ADS)

Nott, Julian

2004-01-01

This paper describes development of three balloon types by the author, all proposed for piloted flights around the world. The first was a superpressure pumpkin used to cross Australia. However, the balloon took up an incorrect shape when inflated. Because of this and other problems, the pumpkin was abandoned and the author built a combined helium-hot air balloon. This in turn was abandoned because it was cumbersome and costly. The author then developed an entirely new system, carrying cryogenic liquid helium to create lift in flight. Two very successful 24-h flights were made. In addition several inventions were developed for crew safety. Perhaps the most important is an entirely new way to protect pilots against sudden cabin pressure loss, with potentially broad use.

Osiris-Rex and Hayabusa2 Sample Cleanroom Design and Construction Planning at NASA-JSC

NASA Technical Reports Server (NTRS)

Righter, Kevin; Pace, Lisa F.; Messenger, Keiko

2018-01-01

Final Paper and not the abstract is attached. The OSIRIS-REx asteroid sample return mission launched to asteroid Bennu September 8, 2016. The spacecraft will arrive at Bennu in late 2019, orbit and map the asteroid, and perform a touch and go (TAG) sampling maneuver in July 2020. After confirma-tion of successful sample stowage, the spacecraft will return to Earth, and the sample return capsule (SRC) will land in Utah in September 2023. Samples will be recovered from Utah and then transported and stored in a new sample cleanroom at NASA Johnson Space Center in Houston. All curation-specific ex-amination and documentation activities related to Ben-nu samples will be conducted in the dedicated OSIRIS-REx sample cleanroom to be built at NASA-JSC.

The Role of Education in Agricultural Projects for Food Security and Poverty Reduction in Kenya

NASA Astrophysics Data System (ADS)

Walingo, Mary Khakoni

2006-05-01

Agricultural development projects have been promoted in many places as a feature of poverty-reduction strategies. Such projects have often been implemented without a strong in-built education component, and hence have had little success. Agricultural projects seek to improve food security by diversifying a household's resource base and facilitating the social and economic empowerment of women. The present study presents a survey designed to assess the relationship between education level and ability to benefit from dairy-development projects in Kenya. Results reveal higher occupation and employment levels among beneficiary than non-beneficiary households. On the other hand, beneficiaries of poverty-reduction schemes require specialized training. Apart from project-specific training, the level of general education alone cannot predict the attainment of project objectives.

Curation, Spacecraft Recovery and Preliminary Examination for the Stardust Mission: A Perspective from the Curatorial Facility

NASA Technical Reports Server (NTRS)

Zolensky, Michael; Nakamura-Messenger, Keiko; Fletcher, Lisa; See, Thomas

2008-01-01

We briefly describe some of the challenges to the Stardust mission, curation and sample preliminary analysis, from the perspective of the Curation Office at the Johnson Space Center. Our goal is to inform persons planning future sample returns, so that they may learn from both our successes and challenges (and avoid some of our mistakes). The Curation office played a role in the mission from its inception, most critically assisting in the design and implementation of the spacecraft contamination control plan, and in planning and documenting the recovery of the spacecraft reentry capsule in Utah. A unique class 100 cleanroom was built to maintain the returned comet and interstellar samples in clean comfort, and to permit dissection and allocation of samples for analysis.

Effects of Solar Array Shadowing on the Power Capability of the Interim Control Module

NASA Technical Reports Server (NTRS)

Fincannon, James; Hojnicki, Jeffrey S.; Garner, James Christopher

1999-01-01

The Interim Control Module (ICM) is being built by the US Naval Research Laboratory (NRL) for NASA as a propulsion module for the International Space Station (ISS). Originally developed as a spinning spacecraft used to move payloads to their final orbit, for ISS, the ICM will be in a fixed orientation and location for long periods resulting in substantial solar panel shadowing. This paper describes the methods used to determine the incident energy incident energy on the ICM solar panels and the power capability of the electric power system (EPS). Applying this methodology has resulted in analyses and assessments used to identify ICM early design changes/options, placement and orientations that enable successful operation of the EPS under a wide variety of anticipated conditions.

The Hinode(Solar-B)Mission: An Overview

NASA Technical Reports Server (NTRS)

Kosugi, T.; Matsuzaki, K.; Sakao, T.; Shimizu, T.; Sone, Y.; Tachikawa, S.; Minesugi, K.; Ohnishi, A.; Yamada, T.; Tsuneta, S.;

Toward Scalable Ion Traps for Quantum Information Processing

DTIC Science & Technology

2010-01-01

3/033031 Abstract. In this paper, we report the design, fabrication and preliminary testing of a 150 zone ion trap array built in a ‘ surface ...gates [4–6]. We report here on the design, fabrication and preliminary testing of a large array built in a ‘ surface -electrode’ geometry [7, 8] and...report the first transport of atomic ions through a surface -electrode trap junction. Transport of ions through a junction has been demonstrated previously

New design incinerator being built

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-09-01

A $14 million garbage-burning facility is being built by Reedy Creek Utilities Co. in cooperation with DOE at Lake Buena Vista, Fla., on the edge of Walt Disney World. The nation's first large-volume slagging pyrolysis incinerator will burn municipal waste in a more beneficial way and supply 15% of the amusement park's energy demands. By studying the new incinerators slag-producing capabilities, engineers hope to design similar facilities for isolating low-level nuclear wastes in inert, rocklike slag.

Optimal design of vertebrate and insect sarcomeres.

PubMed

Otten, E

1987-01-01

This paper offers a model for the normalized length-tension relation of a muscle fiber based upon sarcomere design. Comparison with measurements published by Gordon et al. ('66) shows an accurate fit as long as the inhomogeneity of sarcomere length in a single muscle fiber is taken into account. Sequential change of filament length and the length of the cross-bridge-free zone leads the model to suggest that most vertebrate sarcomeres tested match the condition of optimal construction for the output of mechanical energy over a full sarcomere contraction movement. Joint optimization of all three morphometric parameters suggests that a slightly better (0.3%) design is theoretically possible. However, this theoretical sarcomere, optimally designed for the conversion of energy, has a low normalized contraction velocity; it provides a poorer match to the combined functional demands of high energy output and high contraction velocity than the real sarcomeres of vertebrates. The sarcomeres in fish myotomes appear to be built suboptimally for isometric contraction, but built optimally for that shortening velocity generating maximum power. During swimming, these muscles do indeed contract concentrically only. The sarcomeres of insect asynchronous flight muscles contract only slightly. They are not built optimally for maximum output of energy across the full range of contraction encountered in vertebrate sarcomeres, but are built almost optimally for the contraction range that they do in fact employ.

Analysis of Latest Experience in Design of Industrial Buildings Reconstruction by Constructing Additional Interfloor Overlaps

NASA Astrophysics Data System (ADS)

Peshnina, I.; Sinitsina, O.

2017-11-01

The study relevance is determined by the increasing interest in reconstruction of city historical centers and located in the area of industrial buildings the functional profile of which needs to be changed. The problem of obtaining extra usable spaces in the historical centers of cities is solved by raising the number of storeys in the buildings which can be achieved by the construction of additional built-in inter-floor overlaps. The article is dedicated to the analysis of the recent years’ experience in reconstruction design involving this method in our country and abroad, in the Netherlands, in particular. The article presents the results of the analysis of the experience in reconstruction of the objects by constructing additional inter-floor overlaps and aims to define the optimum construction solution for built-in inter-floor overlapping and to develop non-existing solutions for wide application of this method in the reconstruction of a building with non-unified and unmodulated parameters. It was determined as expedient to apply a monolith reinforced concrete slab with the use of steel profiled flooring as a formwork and reinforcement and steel beams designed as “Built-in Beams” for the construction of built-in inter-floor overlaps in reconstruction. The article will be useful for specialists doing research in the sphere of reconstruction of the buildings and for the practical activity of design engineers.

Progress on the Design of a Perpendicularly Biased 2nd Harmonic Cavity for the Fermilab Booster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madrak, R. L.; Dey, J. E.; Duel, K. L.

2016-10-01

perpendicularly biased 2nd harmonic cavity is being designed and built for the Fermilab Booster. Its purpose is to flatten the bucket at injection and thus change the longitudinal beam distribution to decrease space charge effects. It can also help at extraction. The cavity frequency range is 76 – 106 MHz. The power amplifier will be built using the Y567B tetrode, which is also used for the fundamental mode cavities in the Fermilab Booster. We discuss recent progress on the cavity, the biasing solenoid design and plans for testing the tuner's garnet material

Successes and Techniques Associated with Teaching the Chemistry of Radioactive Wastes.

ERIC Educational Resources Information Center

Williams, Donald H.

1995-01-01

Describes a chemistry course that is built around the topic of radioactive waste and encompasses a large number of chemistry concepts including redox, equilibrium, kinetics, nuclear energy, and the periodic chart. (JRH)

Climate Discovery Online Courses for Educators from NCAR

NASA Astrophysics Data System (ADS)

Henderson, S.; Ward, D. L.; Meymaris, K. K.; Johnson, R. M.; Gardiner, L.; Russell, R.

2008-12-01

The National Center for Atmospheric Research (NCAR) has responded to the pressing need for professional development in climate and global change sciences by creating the Climate Discovery online course series. This series was designed with the secondary geoscience educator in mind. The online courses are based on current and credible climate change science. Interactive learning techniques are built into the online course designs with assignments that encourage active participation. A key element of the online courses is the creation of a virtual community of geoscience educators who exchange ideas related to classroom implementation, student assessment, and lessons plans. Geoscience educators from around the country have participated in the online courses. The ongoing interest from geoscience educators strongly suggests that the NCAR Climate Discovery online courses are a timely and needed professional development opportunity. The intent of NCAR Climate Discovery is to positively impact teachers' professional development scientifically authentic information, (2) experiencing guided practice in conducting activities and using ancillary resources in workshop venues, (3) gaining access to standards-aligned lesson plans, kits that promote hands-on learning, and scientific content that are easily implemented in their classrooms, and (4) becoming a part of a community of educators with whom they may continue to discuss the challenges of pedagogy and content comprehension in teaching climate change in the Earth system context. Three courses make up the Climate Discovery series: Introduction to Climate Change; Earth System Science - A Climate Change Perspective; and Understanding Climate Change Today. Each course, instructed by science education specialists, combines geoscience content, information about current climate research, hands-on activities, and group discussion. The online courses use the web-based Moodle courseware system (open- source software similar to Blackboard and webCT), utilizing its features to promote dialogue as well as provide rich online content and media. A key element of the online courses is the development and support of an online learning community, an essential component in successful online courses. Interactive learning techniques are built into the course designs with assignments that encourage active participation. Educators (both formal and informal) use the courses as a venue to exchange ideas and teaching resources. A unique feature of the courses is the emphasis on hands-on activities, a hallmark of our professional development efforts. This presentation will focus on the lessons learned in the development of the three online courses and our successful recruitment and retention efforts.

Aquarius' Object-Oriented, Plug and Play Component-Based Flight Software

NASA Technical Reports Server (NTRS)

Murray, Alexander; Shahabuddin, Mohammad

2013-01-01

The Aquarius mission involves a combined radiometer and radar instrument in low-Earth orbit, providing monthly global maps of Sea Surface Salinity. Operating successfully in orbit since June, 2011, the spacecraft bus was furnished by the Argentine space agency, Comision Nacional de Actividades Espaciales (CONAE). The instrument, built jointly by NASA's Caltech/JPL and Goddard Space Flight Center, has been successfully producing expectation-exceeding data since it was powered on in August of 2011. In addition to the radiometer and scatterometer, the instrument contains an command & data-handling subsystem with a computer and flight software (FSW) that is responsible for managing the instrument, its operation, and its data. Aquarius' FSW is conceived and architected as a Component-based system, in which the running software consists of a set of Components, each playing a distinctive role in the subsystem, instantiated and connected together at runtime. Component architectures feature a well-defined set of interfaces between the Components, visible and analyzable at the architectural level (see [1]). As we will describe, this kind of an architecture offers significant advantages over more traditional FSW architectures, which often feature a monolithic runtime structure. Component-based software is enabled by Object-Oriented (OO) techniques and languages, the use of which again is not typical in space mission FSW. We will argue in this paper that the use of OO design methods and tools (especially the Unified Modeling Language), as well as the judicious usage of C++, are very well suited to FSW applications, and we will present Aquarius FSW, describing our methods, processes, and design, as a successful case in point.

Sozzy: a hormone-driven autonomous vacuum cleaner

NASA Astrophysics Data System (ADS)

Yamamoto, Masaki

1994-02-01

Domestic robots are promising examples of the application of robotics to personal life. There have been many approaches in this field, but no successful results exist. The problem is that domestic environments are more difficult for robots than other environments, such as factory floors or office floors. Consequently, conventional approaches using a model of human intelligence to design robots have not been successful. In this paper, we report on a prototyped domestic vacuum-cleaning robot that is designed to be able to handle complex environments. The control software is composed of two layers, both of which are generally inspired by behaviors of living creatures. The first layer corresponds to a dynamically reconfigurable system of behaviors implemented in the subsumption architecture. The ability of the robot to support alternate configurations of its behaviors provides the robot with increased robustness. We have conveniently labeled particular configurations as specific `emotions' according to the interpretation of observers of the robot's behavior. The second layer simulates the hormone system. The hormone system is modeled using state variables, increased or decreased by stimuli from the environment. The hormone condition selects the robot's most suitable emotion, according to the changing environments. The robot hardware is built of off-the-shelf parts, such as an embedded CPU, inexpensive home-appliance sensors, and small motors. These parts keep the total building cost to a minimum. The robot also has a vacuum cleaning function to demonstrate its capability to perform useful tasks. We tested the robot in our laboratory, and successfully videotaped its robust behaviors. We also confirmed the hormone system to enhance the robot's plasticity and lifelike quality.

Frontend Receiver Electronics for High Frequency Monolithic CMUT-on-CMOS Imaging Arrays

PubMed Central

Gurun, Gokce; Hasler, Paul; Degertekin, F. Levent

2012-01-01

This paper describes the design of CMOS receiver electronics for monolithic integration with capacitive micromachined ultrasonic transducer (CMUT) arrays for high-frequency intravascular ultrasound imaging. A custom 8-inch wafer is fabricated in a 0.35 μm two-poly, four-metal CMOS process and then CMUT arrays are built on top of the application specific integrated circuits (ASICs) on the wafer. We discuss advantages of the single-chip CMUT-on-CMOS approach in terms of receive sensitivity and SNR. Low-noise and high-gain design of a transimpedance amplifier (TIA) optimized for a forward-looking volumetric-imaging CMUT array element is discussed as a challenging design example. Amplifier gain, bandwidth, dynamic range and power consumption trade-offs are discussed in detail. With minimized parasitics provided by the CMUT-on-CMOS approach, the optimized TIA design achieves a 90 fA/√Hz input referred current noise, which is less than the thermal-mechanical noise of the CMUT element. We show successful system operation with a pulse-echo measurement. Transducer noise-dominated detection in immersion is also demonstrated through output noise spectrum measurement of the integrated system at different CMUT bias voltages. A noise figure of 1.8 dB is obtained in the designed CMUT bandwidth of 10 MHz to 20 MHz. PMID:21859585

Front-end receiver electronics for high-frequency monolithic CMUT-on-CMOS imaging arrays.

PubMed

Gurun, Gokce; Hasler, Paul; Degertekin, F

2011-08-01

This paper describes the design of CMOS receiver electronics for monolithic integration with capacitive micromachined ultrasonic transducer (CMUT) arrays for highfrequency intravascular ultrasound imaging. A custom 8-inch (20-cm) wafer is fabricated in a 0.35-μm two-poly, four-metal CMOS process and then CMUT arrays are built on top of the application specific integrated circuits (ASICs) on the wafer. We discuss advantages of the single-chip CMUT-on-CMOS approach in terms of receive sensitivity and SNR. Low-noise and high-gain design of a transimpedance amplifier (TIA) optimized for a forward-looking volumetric-imaging CMUT array element is discussed as a challenging design example. Amplifier gain, bandwidth, dynamic range, and power consumption trade-offs are discussed in detail. With minimized parasitics provided by the CMUT-on-CMOS approach, the optimized TIA design achieves a 90 fA/√Hz input-referred current noise, which is less than the thermal-mechanical noise of the CMUT element. We show successful system operation with a pulseecho measurement. Transducer-noise-dominated detection in immersion is also demonstrated through output noise spectrum measurement of the integrated system at different CMUT bias voltages. A noise figure of 1.8 dB is obtained in the designed CMUT bandwidth of 10 to 20 MHz.

Sharp and the Jules Verne Launcher

NASA Astrophysics Data System (ADS)

Hunter, John; Cartland, Harry

1996-03-01

Lawrence Livermore National Laboratory (LLNL) has built the worlds largest hydrogen gas gun called SHARP, (Super High Altitude Research Project). Originally designed to launch 5 kg to a 450 km altitude, SHARP is configured horizontally at Site 300 in Tracy, California. SHARP is successfully delivering 5 kg scramjets at Mach 9 in aerophysics tests. Some of the results of the scramjet tests are enlightening and are presented insofar as they are relevant to future launches into space. Using a light gas gun to launch payloads into orbit has been analyzed. We look at LEO (Low Earth Orbit), GEO (Geosynchronous Earth Orbit), and LO (Lunar Orbit). We present a conceptual design for a large light gas gun called the Jules Verne Launcher (JVL). The JVL can deliver 3.3 metric tons to a 500 km low earth orbit. We anticipate one launch per day. We present the history of light gas guns, the SHARP design and performance, and the JVL design. Another section is devoted to the vehicle environment and resultant design. Lastly, we present a cost analysis. Our results indicated that the JVL will be able to deliver 1000 metric tons of payload to LEO yearly. The cost will be 5% of the best US rocket delivery cost. This technology will enable the next phase of man's exploration of space.

US-75 ICM system as-built design : Dallas Integrated Corridor Management (ICM) demonstration project.

DOT National Transportation Integrated Search

2015-05-01

This As-Built document for the US-75 Integrated Corridor Management (ICM) Program has been developed as part of the US Department of Transportation Integrated Corridor Management Initiative. The basic premise behind the ICM initiative is that indepen...

Design high water clearances for highway pavements : [executive summary].

DOT National Transportation Integrated Search

2008-01-01

The majority of state roads in Florida are built using asphalt concrete surfaces. They are constructed in layers. The bottom layer consists of the native soil. The top layer is the surface course, or pavement. It is built upon one or more intermediat...

Exposure to natural environments, and photographs of natural environments, promotes more positive body image.

PubMed

Swami, Viren; Barron, David; Furnham, Adrian

2018-03-01

Five studies were conducted to understand the impact of nature exposure on body image. In three studies using different designs and outcome measures, British university students were exposed to photographs of natural or built environments. Results indicated that exposure to images of natural, but not built, environments resulted in improved state body image. In Study 4, British community participants went on a walk in a natural or built environment, with results indicating that the walk in a natural environment resulted in significantly higher state body appreciation, whereas the walk in a built environment resulted in significantly lower scores. In Study 5, British participants were recruited as they were entering a designed green space on their own volition. Results indicated that spending time in the green space led to improved state body appreciation. These results indicate that exposure to isomorphic or in-situ natural environments has positive effects on state body image. Copyright © 2017 Elsevier Ltd. All rights reserved.

Planning and conducting a multi-institutional project on fatigue.

PubMed

Nail, L M; Barsevick, A M; Meek, P M; Beck, S L; Jones, L S; Walker, B L; Whitmer, K R; Schwartz, A L; Stephen, S; King, M E

1998-09-01

To describe the process used in proposal development and study implementation for a complex multisite project on cancer treatment-related fatigue (CRF), identify strategies used to manage the project, and provide recommendations for teams planning multisite research. Information derived from project team meeting records, correspondence, proposals, and personal recollection. The project was built on preexisting relationships among the three site investigators who then built a team including faculty, research coordinators, staff nurses, and students. Study sites had a range of organizational models, and the proposal was designed to capitalize on the organizational and resource strengths of each setting. Three team members drawn from outside oncology nursing provided expertise in measurement and experience with fatigue in other populations. Planning meetings were critical to the success of the project. Conference calls, fax technology, and electronic mail were used for communication. Flexibility was important in managing crises and shifting responsibility for specific components of the work. The team documented and evaluated the process used for multisite research, completed a major instrumentation study, and developed a cognitive-behavioral intervention for CRF. Accomplishments during the one-year planning grant exceeded initial expectations. The process of conducting multisite research is complex, especially when the starting point is a planning grant with specific research protocols to be developed and implemented over one year. Explicit planning for decision-making processes to be used throughout the project, acknowledging the differences among the study settings and planning the protocols to capitalize upon those differences, and recruiting a strong research team that included a member with planning grant and team-building expertise were essential elements for success. Specific recommendations for others planning multisite research are related to team-building, team membership, communication, behavioral norms, role flexibility, resources, feedback, problem management, and shared recognition.

Built environment affecting visitors' walking choice in commercial areas? - A study with GPS experiments

NASA Astrophysics Data System (ADS)

Hahm, Y.; Yoon, H.

2016-12-01

Retail location is one of the most critical factors explaining the success of store operations. Store owners prefer to choose locations with high visibility and convenient transportation, which might be likely reasons for higher pedestrian volume, hence larger chance to capture impulse shoppers, resulting in more profits. While researches have focused on discerning relationship between pedestrian route choice and physical environments via indirect measures such as survey questionnaire and interviews, recent technologies such as Global Positioning System (GPS) enables collecting direct and precise waking route data. In this study, we investigate the physical environments in which pedestrians prefer to be in commercial district, and further analyze if such locations encompass stores with higher store revenues. The primary method is GPS experiment and travel diary for over hundred visitors of the study site, Hongik University commercial areas in Seoul, South Korea, and statistical analysis, Structural Equation Model (SEM). With SEM, we could assess endogenous latent variables indicating built environments, such as Density, Diversity, Destination Accessibility, Design, and Retail Attraction, and exogenous latent variable, the pedestrian walking choice, based on the observation of pedestrian volume and walking speed. Observed variables include the number of stores, building uses, kind of retail, and pedestrian volume, and walking speed. This research will shed light on planning commercial districts, emphasizing the role of pedestrian walking in the success of retail business, and providing a clue on how to encourage pedestrian visitation by improving physical environment. This work is supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Science, ICT & Future Planning (No. 2015R1C1A2A01055615)

A quality by design approach to optimization of emulsions for electrospinning using factorial and D-optimal designs.

PubMed

Badawi, Mariam A; El-Khordagui, Labiba K

2014-07-16

Emulsion electrospinning is a multifactorial process used to generate nanofibers loaded with hydrophilic drugs or macromolecules for diverse biomedical applications. Emulsion electrospinnability is greatly impacted by the emulsion pharmaceutical attributes. The aim of this study was to apply a quality by design (QbD) approach based on design of experiments as a risk-based proactive approach to achieve predictable critical quality attributes (CQAs) in w/o emulsions for electrospinning. Polycaprolactone (PCL)-thickened w/o emulsions containing doxycycline HCl were formulated using a Span 60/sodium lauryl sulfate (SLS) emulsifier blend. The identified emulsion CQAs (stability, viscosity and conductivity) were linked with electrospinnability using a 3(3) factorial design to optimize emulsion composition for phase stability and a D-optimal design to optimize stable emulsions for viscosity and conductivity after shifting the design space. The three independent variables, emulsifier blend composition, organic:aqueous phase ratio and polymer concentration, had a significant effect (p<0.05) on emulsion CQAs, the emulsifier blend composition exerting prominent main and interaction effects. Scanning electron microscopy (SEM) of emulsion-electrospun NFs and desirability functions allowed modeling of emulsion CQAs to predict electrospinnable formulations. A QbD approach successfully built quality in electrospinnable emulsions, allowing development of hydrophilic drug-loaded nanofibers with desired morphological characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

Computer-automated evolution of an X-band antenna for NASA's Space Technology 5 mission.

PubMed

Hornby, Gregory S; Lohn, Jason D; Linden, Derek S

2011-01-01

Whereas the current practice of designing antennas by hand is severely limited because it is both time and labor intensive and requires a significant amount of domain knowledge, evolutionary algorithms can be used to search the design space and automatically find novel antenna designs that are more effective than would otherwise be developed. Here we present our work in using evolutionary algorithms to automatically design an X-band antenna for NASA's Space Technology 5 (ST5) spacecraft. Two evolutionary algorithms were used: the first uses a vector of real-valued parameters and the second uses a tree-structured generative representation for constructing the antenna. The highest-performance antennas from both algorithms were fabricated and tested and both outperformed a hand-designed antenna produced by the antenna contractor for the mission. Subsequent changes to the spacecraft orbit resulted in a change in requirements for the spacecraft antenna. By adjusting our fitness function we were able to rapidly evolve a new set of antennas for this mission in less than a month. One of these new antenna designs was built, tested, and approved for deployment on the three ST5 spacecraft, which were successfully launched into space on March 22, 2006. This evolved antenna design is the first computer-evolved antenna to be deployed for any application and is the first computer-evolved hardware in space.

New drilling rigs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tubb, M.

1981-02-01

Friede and Goldman Ltd. of New Orleans, Louisiana has a successful drilling rig, the L-780 jack-up series. The triangular-shaped drilling vessel measures 180 x 176 ft. and is equipped with three 352 ft legs including spud cans. It is designed to work in up to 250 ft waters and drill to 20,000 ft depths. The unit is scheduled to begin initial drilling operations in the Gulf of Mexico for Arco. Design features are included for the unit. Davie Shipbuilding Ltd. has entered the Mexican offshore market with the signing of a $40,000,000 Canadian contract for a jack-up to work inmore » 300 ft water depths. Baker Marine Corporation has contracted with the People's Republic of China for construction of two self-elevating jack-ups. The units will be built for Magnum Marine, headquartered in Houston. Details for the two rigs are given. Santa Fe International Corporation has ordered a new jack-up rig to work initially in the Gulf of Suez. The newly ordered unit, Rig 136, will be the company's fourth offshore drilling rig now being built in the Far East. Temple Drilling Company has signed a construction contract with Bethlehem Steel for a jack-up to work in 200 ft water depths. Penrod Drilling Company has ordered two additional cantilever type jack-ups for Hitachi Shipbuilding and Engineering Co. Ltd. of Japan. Two semi-submersibles, capable of working in up to 2000 ft water depths, have been ordered by two Liberian companies. Details for these rigs are included. (DP)« less

Extraction of business relationships in supply networks using statistical learning theory.

PubMed

Zuo, Yi; Kajikawa, Yuya; Mori, Junichiro

2016-06-01

Supply chain management represents one of the most important scientific streams of operations research. The supply of energy, materials, products, and services involves millions of transactions conducted among national and local business enterprises. To deliver efficient and effective support for supply chain design and management, structural analyses and predictive models of customer-supplier relationships are expected to clarify current enterprise business conditions and to help enterprises identify innovative business partners for future success. This article presents the outcomes of a recent structural investigation concerning a supply network in the central area of Japan. We investigated the effectiveness of statistical learning theory to express the individual differences of a supply chain of enterprises within a certain business community using social network analysis. In the experiments, we employ support vector machine to train a customer-supplier relationship model on one of the main communities extracted from a supply network in the central area of Japan. The prediction results reveal an F-value of approximately 70% when the model is built by using network-based features, and an F-value of approximately 77% when the model is built by using attribute-based features. When we build the model based on both, F-values are improved to approximately 82%. The results of this research can help to dispel the implicit design space concerning customer-supplier relationships, which can be explored and refined from detailed topological information provided by network structures rather than from traditional and attribute-related enterprise profiles. We also investigate and discuss differences in the predictive accuracy of the model for different sizes of enterprises and types of business communities.

Twinkle - a mission to unravel the story of planets in our galaxy

NASA Astrophysics Data System (ADS)

Tessenyi, Marcell

2016-07-01

The study of exoplanets has been incredibly successful over the past 20 years: nearly 2000 planets have been discovered, and along these discoveries fundamental parameters such as mass, radius and semi-major axis have been obtained. In the past decade, pioneering results have been obtained using transit spectroscopy with Hubble, Spitzer and ground-based facilities, which have enabled the detection of a few of the most abundant chemical species, the presence of clouds, and also permitted the study of the planetary thermal structure. Twinkle is a small, dedicated satellite designed to measure the atmospheric composition of exoplanets. Twinkle is a cost-effective spacecraft being built on a short timescale and is planned for a launch by 2019. The satellite uses an existing platform designed by Surrey Satellite Technology Ltd, and instrumentation built by a consortium of UK institutes. Twinkle will analyse >100 exoplanets in our galaxy and a few objects in our solar system. Its infrared spectrograph will enable observations of a wide range of planet types including super-Earths and hot-Jupiters. Some of the target planets are orbiting stars similar to our Sun and some are orbiting cooler red-dwarfs. For the largest planets orbiting bright stars, Twinkle will even be able to produce maps of clouds and temperature. The Twinkle instrument will be composed of a visible-IR spectrograph (between 0.5 and 5mum) with resolving power Rsim300, and will orbit Earth on a sun-synchronous polar orbit. More information on Twinkle can be found on our website: www.twinkle-spacemission.co.uk

Flexible detection optics for light scattering

NASA Astrophysics Data System (ADS)

Taratuta, Victor G.; Hurd, Alan J.; Meyer, Robert B.

1984-05-01

We have designed and built a compact, modular apparatus for the collection, viewing, and detection of scattered light for less than 1200, based on a commercially available optical bench. The novelty of our instrument is that it has the flexibility of modular design while allowing the user to see exactly what is happening: both the real image of the sample and the spatial coherence of the scattered light can be examined. There is built-in control over polarization, filtering, magnification, and other parameters.

Reducing the Cost of System Administration of a Disk Storage System Built from Commodity Components

DTIC Science & Technology

2000-05-01

quickly by using checkpointing and roll-forward logs. Microsoft Tiger is a video server built from commodity PCs which they call “cubs” [ BBD +96, BFD97...20 cents per megabyte using street prices of components. 3.2.2 Redundancy In designing the TD prototype, we have taken care to ensure it does not have... Td /GridPix/, 1999. [ATP99] Satoshi Asami, Nisha Talagala, and David Patterson. Designing a self-maintaining storage system. In Proceedings of the

Validation Data for Mechanical System Algorithms Used in Building Energy Analysis Programs.

DTIC Science & Technology

1982-02-01

15 Zone Design 15 Built-Up Air Handler 15 Ventilation Requirements 16 The DES 16 Duct Design 17 Air -Delivery System 17 VAV Operation 17 Constant Volume...observed to operate well at reduced air flows, even at low flow in the so- called surge region. Recommendations 1. The HVAC system and component...With Inlet Guide Vanes Operating Within a Built-Up Air Handler 31 Test 2 -- Boiler Operation, Capacity, Efficiency, and Stand-By Losses 32 Test 3

Automated iodine monitor system. [for aqueous solutions

NASA Technical Reports Server (NTRS)

1973-01-01

The feasibility of a direct spectrophotometric measurement of iodine in water was established. An iodine colorimeter, was built to demonstrate the practicality of this technique. The specificity of this method was verified when applied to an on-line system where a reference solution cannot be used, and a preliminary design is presented for an automated iodine measuring and controlling system meeting the desired specifications. An Automated iodine monitor/controller system based on this preliminary design was built, tested, and delivered to the Johnson Space Center.

Development and Verification of a Novel Robot-Integrated Fringe Projection 3D Scanning System for Large-Scale Metrology.

PubMed

Du, Hui; Chen, Xiaobo; Xi, Juntong; Yu, Chengyi; Zhao, Bao

2017-12-12

Large-scale surfaces are prevalent in advanced manufacturing industries, and 3D profilometry of these surfaces plays a pivotal role for quality control. This paper proposes a novel and flexible large-scale 3D scanning system assembled by combining a robot, a binocular structured light scanner and a laser tracker. The measurement principle and system construction of the integrated system are introduced. A mathematical model is established for the global data fusion. Subsequently, a robust method is introduced for the establishment of the end coordinate system. As for hand-eye calibration, the calibration ball is observed by the scanner and the laser tracker simultaneously. With this data, the hand-eye relationship is solved, and then an algorithm is built to get the transformation matrix between the end coordinate system and the world coordinate system. A validation experiment is designed to verify the proposed algorithms. Firstly, a hand-eye calibration experiment is implemented and the computation of the transformation matrix is done. Then a car body rear is measured 22 times in order to verify the global data fusion algorithm. The 3D shape of the rear is reconstructed successfully. To evaluate the precision of the proposed method, a metric tool is built and the results are presented.

Software Development for the Hobby-Eberly Telescope's Segment Alignment Maintenance System using LABView

NASA Technical Reports Server (NTRS)

Hall, Drew P.; Ly, William; Howard, Richard T.; Weir, John; Rakoczy, John; Roe, Fred (Technical Monitor)

2002-01-01

The software development for an upgrade to the Hobby-Eberly Telescope (HET) was done in LABView. In order to improve the performance of the HET at the McDonald Observatory, a closed-loop system had to be implemented to keep the mirror segments aligned during periods of observation. The control system, called the Segment Alignment Maintenance System (SAMs), utilized inductive sensors to measure the relative motions of the mirror segments. Software was developed in LABView to tie the sensors, operator interface, and mirror-control motors together. Developing the software in LABView allowed the system to be flexible, understandable, and able to be modified by the end users. Since LABView is built using block diagrams, the software naturally followed the designed control system's block and flow diagrams, and individual software blocks could be easily verified. LABView's many built-in display routines allowed easy visualization of diagnostic and health-monitoring data during testing. Also, since LABView is a multi-platform software package, different programmers could develop the code remotely on various types of machines. LABView s ease of use facilitated rapid prototyping and field testing. There were some unanticipated difficulties in the software development, but the use of LABView as the software "language" for the development of SAMs contributed to the overall success of the project.

Multiple Deltas Built Out Over Time

NASA Image and Video Library

2014-12-08

This diagram depicts a vertical cross section through geological layers deposited by rivers, deltas and lakes. Deposits from a series of successive deltas build out increasingly high in elevation as they migrate toward the center of the basin.

Public spaces and urban sustainability in the tropical built environment

NASA Astrophysics Data System (ADS)

Yusof, Y. M.; Kozlowski, M.

2018-01-01

Sustainability is an overarching sense of responsibility towards the future. On a city-wide level, urban sustainability incorporates a wide body of changes especially as they relate to the built environment, all of which intended at creating a livable place. This paper discusses existing public spaces in view of their achievement against a set of criteria for the built environment. The paper introduces performance design criteria for the tropical built environment. The key findings indicate that long-term strategies, guidance and directions for the city and region can achieve development which corresponds to local climate, synergies and provide a higher proportion of public spaces that offer something for everyone.

Ultra-Efficient and Power Dense Electric Motors for U. S. Industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Melfi, Michael J.; Schiferl, Richard F.; Umans, Stephen D.

2013-03-12

The primary purpose of this project was to combine the ease-of-installation and ease-of-use attributes of industrial induction motors with the low-loss and small size and weight advantages of PM motors to create an ultra-efficient, high power density industrial motor that can be started across-the-line or operated from a standard, Volts/Hertz drive without the need for a rotor position feedback device. PM motor products that are currently available are largely variable speed motors that require a special adjustable speed drive with rotor position feedback. The reduced size and weight helps to offset the magnet cost in order make these motors commerciallymore » viable. The scope of this project covers horsepower ratings from 20 ? 500. Prototypes were built and tested at ratings ranging from 30 to 250 HP. Since fans, pumps and compressors make up a large portion of industrial motor applications, the motor characteristics are tailored to those applications. Also, since there is extensive use of adjustable frequency inverters in these applications, there is the opportunity to design for an optimal pole number and operate at other than 60 Hz frequency when inverters are utilized. Designs with four and eight pole configurations were prototyped as part of this work. Four pole motors are the most commonly used configuration in induction motors today. The results of the prototype design, fabrication, and testing were quite successful. The 50 HP rating met all of the design goals including efficiency and power density. Tested values of motor losses at 50 HP were 30% lower than energy efficient induction motors and the motor weight is 35% lower than the energy efficient induction motor of the same rating. Further, when tested at the 30 HP rating that is normally built in this 286T frame size, the efficiency far exceeds the project design goals with 30 HP efficiency levels indicating a 55% reduction in loss compared to energy efficient motors with a motor weight that is a few percentage points lower than the energy efficient motor. This 30 HP rating full load efficiency corresponds to a 46% reduction in loss compared to a 30 HP NEMA Premium? efficient motor. The cost goals were to provide a two year or shorter efficiency-based payback of a price premium associated with the magnet cost in these motors. That goal is based on 24/7 operation with a cost of electricity of 10 cents per kW-hr. Similarly, the 250 HP prototype efficiency testing was quite successful. In this case, the efficiency was maximized with a slightly less aggressive reduction in active material. The measured full load efficiency of 97.6% represents in excess of a 50% loss reduction compared to the equivalent NEMA Premium Efficiency induction motor. The active material weight reduction was a respectable 14.5% figure. This larger rating demonstrated both the scalability of this technology and also the ability to flexibly trade off power density and efficiency. In terms of starting performance, the 30 ? 50 HP prototypes were very extensively tested. The demonstrated capability included the ability to successfully start a load with an inertia of 25 times the motor?s own inertia while accelerating against a load torque following a fan profile at the motor?s full nameplate power rating. This capability will provide very wide applicability of this motor technology. The 250 HP prototype was also tested for starting characteristics, though without a coupled inertia and load torque. As a result it was not definitively proven that the same 25 times the motor?s own inertia could be started and synchronized successfully at 250 HP. Finite element modeling implies that this load could be successfully started, but it has not yet been confirmed by a test.« less

The EBIT Calorimeter Spectrometer: a new, permanent user facility at the LLNL EBIT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Porter, F S; Beiersdorfer, P; Brown, G V

The EBIT Calorimeter Spectrometer (ECS) is currently being completed and will be installed at the EBIT facility at the Lawrence Livermore National Laboratory in October 2007. The ECS will replace the smaller XRS/EBIT microcalorimeter spectrometer that has been in almost continuous operation since 2000. The XRS/EBIT was based on a spare laboratory cryostat and an engineering model detector system from the Suzaku/XRS observatory program. The new ECS spectrometer was built to be a low maintenance, high performance implanted silicon microcalorimeter spectrometer with 4 eV resolution at 6 keV, 32 detector channels, 10 {micro}s event timing, and capable of uninterrupted acquisitionmore » sessions of over 60 hours at 50 mK. The XRS/EBIT program has been very successful, producing many results on topics such as laboratory astrophysics, atomic physics, nuclear physics, and calibration of the spectrometers for the National Ignition Facility. The ECS spectrometer will continue this work into the future with improved spectral resolution, integration times, and ease-of-use. We designed the ECS instrument with TES detectors in mind by using the same highly successful magnetic shielding as our laboratory TES cryostats. This design will lead to a future TES instrument at the LLNL EBIT. Here we discuss the legacy of the XRS/EBIT program, the performance of the new ECS spectrometer, and plans for a future TES instrument.« less

Mechanic watches a General Electric I-40 Engine Fire

NASA Image and Video Library

1948-01-21

A mechanic watches the firing of a General Electric I-40 turbojet at the National Advisory Committee for Aeronautics (NACA) Lewis Flight Propulsion Laboratory. The military selected General Electric’s West Lynn facility in 1941 to secretly replicate the centrifugal turbojet engine designed by British engineer Frank Whittle. General Electric’s first attempt, the I-A, was fraught with problems. The design was improved somewhat with the subsequent I-16 engine. It was not until the engine's next reincarnation as the I-40 in 1943 that General Electric’s efforts paid off. The 4000-pound thrust I-40 was incorporated into the Lockheed Shooting Star airframe and successfully flown in June 1944. The Shooting Star became the US’s first successful jet aircraft and the first US aircraft to reach 500 miles per hour. NACA Lewis studied all of General Electric’s centrifugal turbojet models during the 1940s. In 1945 the entire Shooting Star aircraft was investigated in the Altitude Wind Tunnel. Engine compressor performance and augmentation by water injection; comparison of different fuel blends in a single combustor; and air-cooled rotors were studied. The mechanic in this photograph watches the firing of a full-scale I-40 in the Jet Propulsion Static Laboratory. The facility was quickly built in 1943 specifically in order to test the early General Electric turbojets. The I-A was secretly analyzed in the facility during the fall of 1943.

System Software Framework for System of Systems Avionics

NASA Technical Reports Server (NTRS)

Ferguson, Roscoe C.; Peterson, Benjamin L; Thompson, Hiram C.

2005-01-01

Project Constellation implements NASA's vision for space exploration to expand human presence in our solar system. The engineering focus of this project is developing a system of systems architecture. This architecture allows for the incremental development of the overall program. Systems can be built and connected in a "Lego style" manner to generate configurations supporting various mission objectives. The development of the avionics or control systems of such a massive project will result in concurrent engineering. Also, each system will have software and the need to communicate with other (possibly heterogeneous) systems. Fortunately, this design problem has already been solved during the creation and evolution of systems such as the Internet and the Department of Defense's successful effort to standardize distributed simulation (now IEEE 1516). The solution relies on the use of a standard layered software framework and a communication protocol. A standard framework and communication protocol is suggested for the development and maintenance of Project Constellation systems. The ARINC 653 standard is a great start for such a common software framework. This paper proposes a common system software framework that uses the Real Time Publish/Subscribe protocol for framework-to-framework communication to extend ARINC 653. It is highly recommended that such a framework be established before development. This is important for the success of concurrent engineering. The framework provides an infrastructure for general system services and is designed for flexibility to support a spiral development effort.

A Disadvantaged Advantage in Walkability: Findings from Socioeconomic and Geographic Analysis of National Built Environment Data in the United States.

EPA Science Inventory

Urban form-the structure of the built environment-can influence physical activity, yet little is known about how walkable design differs according to neighborhood sociodemographic composition. We studied how walkable urban form varies by neighborhood sociodemographic composition,...

Environmental Stewardship through Service Learning

ERIC Educational Resources Information Center

Kaye, Cathryn Berger

2011-01-01

New school buildings often grab headlines that highlight their green features and LEED (Leadership in Energy and Environmental Design) certification, yet nearly 90% of schools in the United States were built before 1985, with the largest portion built from 1950-69 to accommodate the baby boom generation (National Clearinghouse for Educational…

An Interdisciplinary Microprocessor Project.

ERIC Educational Resources Information Center

Wilcox, Alan D.; And Others

1985-01-01

Describes an unusual project in which third-year computer science students designed and built a four-bit multiplier circuit and then combines it with software to complete a full 16-bit multiplication. The multiplier was built using TTL components, interfaced with a Z-80 microprocessor system, and programed in assembly language. (JN)

Transitioning to High Performance Homes: Successes and Lessons Learned From Seven Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widder, Sarah H.; Kora, Angela R.; Baechler, Michael C.

2013-03-01

As homebuyers are becoming increasingly concerned about rising energy costs and the impact of fossil fuels as a major source of greenhouse gases, the returning new home market is beginning to demand energy-efficient and comfortable high-performance homes. In response to this, some innovative builders are gaining market share because they are able to market their homes’ comfort, better indoor air quality, and aesthetics, in addition to energy efficiency. The success and marketability of these high-performance homes is creating a builder demand for house plans and information about how to design, build, and sell their own low-energy homes. To help makemore » these and other builders more successful in the transition to high-performance construction techniques, Pacific Northwest National Laboratory (PNNL) partnered with seven interested builders in the hot humid and mixed humid climates to provide technical and design assistance through two building science firms, Florida Home Energy and Resources Organization (FL HERO) and Calcs-Plus, and a designer that offers a line of stock plans designed specifically for energy efficiency, called Energy Smart Home Plans (ESHP). This report summarizes the findings of research on cost-effective high-performance whole-house solutions, focusing on real-world implementation and challenges and identifying effective solutions. The ensuing sections provide project background, profile each of the builders who participated in the program, and describe their houses’ construction characteristics, key challenges the builders encountered during the construction and transaction process); and present primary lessons learned to be applied to future projects. As a result of this technical assistance, 17 homes have been built featuring climate-appropriate efficient envelopes, ducts in conditioned space, and correctly sized and controlled heating, ventilation, and air-conditioning systems. In addition, most builders intend to integrate high-performance features into most or all their homes in the future. As these seven builders have demonstrated, affordable, high-performance homes are possible, but require attention to detail and flexibility in design to accommodate specific regional geographic or market-driven constraints that can increase cost. With better information regarding how energy-efficiency trade-offs or design choices affect overall home performance, builders can make informed decisions regarding home design and construction to minimize cost without sacrificing performance and energy savings.« less

Municipal Officials' Participation in Built Environment Policy Development in the United States.

PubMed

Lemon, Stephenie C; Goins, Karin Valentine; Schneider, Kristin L; Brownson, Ross C; Valko, Cheryl A; Evenson, Kelly R; Eyler, Amy A; Heinrich, Katie M; Litt, Jill; Lyn, Rodney; Reed, Hannah L; Tompkins, Nancy O'Hara; Maddock, Jay

2015-01-01

This study examined municipal officials' participation in built environment policy initiatives focused on land use design, transportation, and parks and recreation. Web-based cross-sectional survey. Eighty-three municipalities with 50,000 or more residents in eight states. Four hundred fifty-three elected and appointed municipal officials. Outcomes included self-reported participation in land use design, transportation, and parks and recreation policy to increase physical activity. Independent variables included respondent position; perceptions of importance, barriers, and beliefs regarding physical activity and community design and layout; and physical activity partnership participation. Multivariable logistic regression models. Compared to other positions, public health officials had lower participation in land use design (78.3% vs. 29.0%), transportation (78.1% vs. 42.1%), and parks and recreation (67.1% vs. 26.3%) policy. Perceived limited staff was negatively associated with participation in each policy initiative. Perceptions of the extent to which physical activity was considered in community design and physical activity partnership participation were positively associated with participation in each. Perceived lack of collaboration was associated with less land use design and transportation policy participation, and awareness that community design affects physical activity was associated with more participation. Perceived lack of political will was associated with less parks and recreation policy participation. Public health officials are underrepresented in built environment policy initiatives. Improving collaborations may improve municipal officials' policy participation.

Properties of large nearly perfect crystals at very low temperatures

NASA Technical Reports Server (NTRS)

Davis, W.; Krack, K. R.; Richard, J. P.; Weber, J.

1983-01-01

A liquid helium cryostat of a size and construction unavailable commercially, was built for use in measuring the Q of several materials at milli-Kelvin temperatures. The design and testing of the cryostat is described as well as the design of the experiment vacuum chamber and adaptor for the dilution refrigerator insert. Theory, design, and testing are also discussed for the magnetic coils built to levitate the materials so as to isolate them and increase the measured Q. A four point suspension with capacitor end plates as the transducer was used to obtain preliminary Q measurements of 6061 aluminum alloy and single crystal silicon. Results are tabulated.

Analysis and Design of Phase Change Thermal Control for Light Emitting Diode (LED) Spacesuit Helmet Lights

NASA Technical Reports Server (NTRS)

Bue, Grant C.; Nguyen, Hiep X.; Keller, John R.

2010-01-01

LED Helmet Extravehicular Activity Helmet Interchangeable Portable (LEHIP) lights for the Extravehicular Mobility Unit (EMU) have been built and tested and are currently being used on the International Space Station. A design is presented of the passive thermal control system consisting of a chamber filled with aluminum foam and wax. A thermal math model of LEHIP was built and correlated by test to show that the thermal design maintains electronic components within hot and cold limits for a 7 hour spacewalk in the most extreme EVA average environments, and do not pose a hazard to the crew or to components of the EMU.

Elastic and inelastic scattering of positrons in gases and solids

NASA Technical Reports Server (NTRS)

Mcgowan, J. W.

1972-01-01

Three apparatuses were designed and built: The first, which is now operative, was designed to study the details of positron thermalization in solids and the subsequent emission of the low energy positrons from moderating foils; The second apparatus now under test is a positron bottle similar in design to an electron trap. It was built to store positrons at a fixed energy and to look at the number of stored positrons (storage time) as a function of a scattering gas in the vacuum chamber. The third apparatus is a crossed beam apparatus where positron-, alkali scattering will be studied. Much of the apparatus is now under test with electrons.

Design of a multi-spectral imager built using the compressive sensing single-pixel camera architecture

NASA Astrophysics Data System (ADS)

McMackin, Lenore; Herman, Matthew A.; Weston, Tyler

2016-02-01

We present the design of a multi-spectral imager built using the architecture of the single-pixel camera. The architecture is enabled by the novel sampling theory of compressive sensing implemented optically using the Texas Instruments DLP™ micro-mirror array. The array not only implements spatial modulation necessary for compressive imaging but also provides unique diffractive spectral features that result in a multi-spectral, high-spatial resolution imager design. The new camera design provides multi-spectral imagery in a wavelength range that extends from the visible to the shortwave infrared without reduction in spatial resolution. In addition to the compressive imaging spectrometer design, we present a diffractive model of the architecture that allows us to predict a variety of detailed functional spatial and spectral design features. We present modeling results, architectural design and experimental results that prove the concept.

Implementing AIM-based monitoring for natural resource management

USDA-ARS?s Scientific Manuscript database

Successful monitoring programs are built on clearly-defined objectives, thorough planning, and organized implementation. However, natural resource management decisions need to be made at many different organizational levels and scales – from local to national. Developing separate monitoring programs...

Solar Concentrator Advanced Development Program

NASA Technical Reports Server (NTRS)

Knasel, Don; Ehresman, Derik

1989-01-01

The Solar Concentrator Advanced Development Project has successfully designed, fabricated, and tested a full scale prototypical solar dynamic concentrator for space station applications. A Truss Hexagonal Panel reflector was selected as a viable solar concentrator concept to be used for space station applications. This concentrator utilizes a modular design approach and is flexible in attainable flux profiles and assembly techniques. The detailed design of the concentrator, which included structural, thermal and optical analysis, identified the feasibility of the design and specific technologies that were required to fabricate it. The needed surface accuracy of the reflectors surface was found to be very tight, within 5 mrad RMS slope error, and results in very close tolerances for fabrication. To meet the design requirements, a modular structure composed of hexagonal panels was used. The panels, made up of graphite epoxy box beams provided the strength, stiffness and dimensional stability needed. All initial project requirements were met or exceeded by hardware demonstration. Initial testing of structural repeatability of a seven panel portion of the concentrator was followed by assembly and testing of the full nineteen panel structure. The testing, which consisted of theodolite and optical measurements over an assembly-disassembly-reassembly cycle, demonstrated that the concentrator maintained the as-built contour and optical characteristics. The facet development effort within the project, which included developing the vapor deposited reflective facet, produced a viable design with demonstrated optical characteristics that are within the project goals.

Mentoring Undergraduate Students through the Space Shuttle Hitchhiker GoldHELOX Project

NASA Astrophysics Data System (ADS)

Moody, J. Ward; Barnes, Jonathan; Roming, Peter; Durfee, Dallin; Campbell, Branton; Turley, Steve; Eastman, Paul

2015-01-01

In the late 1980s a team of four BYU undergraduate students designed a space-based telescope to image the sun in soft x-rays from 171-181 Angstroms to gain information on microflares and their relation to the corona-chromosphere transition region. The telescope used a near-normal incidence multi-layered mirror imaging onto film through a micro-channel plate. The system was capable of 1.0 sec time resolution and 2.5 arcsec spatial resolution. Aided by a NASA grant in 1991, a system was built and successfully tested in 1998 at Marshall Space Flight Center. Originally designed to be deployed from a Get-Away-Special (GAS) canister in the bay of a space shuttle, the good results of this test elevated GoldHelox to greater-priority Hitchhiker status. Even so technical and procedural difficulties delayed a launch until after 2003. Unfortunately after the Columbia re-entry break-up in February 2003, the Hitchhiker program was cancelled and the GoldHelox project ended.Well over 200 undergraduate students worked on GoldHelox. Many of these have since earned advanced degrees in a variety of technical fields. Several have gone on to work in the space industry, becoming NASA scientists and engineers with one becoming a PI on the Swift satellite. The broad range of talent on the team has included students majoring in physics, astronomy, mechanical engineering, electrical engineering, manufacturing engineering, design engineering, business and even English majors who have written technical and public relations documents. We report on lessons learned and the pitfalls and successes of this unique mentoring experience.

Advancements in Magnetic Resonance–Guided Robotic Interventions in the Prostate

PubMed Central

Macura, Katarzyna J.; Stoianovici, Dan

2011-01-01

Magnetic resonance imaging (MRI) provides more detailed anatomical images of the prostate compared with the transrectal ultrasound imaging. Therefore, for the purpose of intervention in the prostate gland, diagnostic or therapeutic, MRI guidance offers a possibility of more precise targeting that may be crucial to the success of prostate interventions. However, access within the scanner is limited for manual instrument handling and the MR environment is most demanding among all imaging equipment with respect to the instrumentation used. A solution to this problem is the use of MR-compatible robots purposely designed to operate in the space and environmental restrictions inside the MR scanner allowing real-time interventions. Building an MRI-compatible robot is a very challenging engineering task because, in addition to the material restrictions that MRI instruments have, the robot requires actuators and sensors that limit the type of energies that can be used. Several important design problems have to be overcome before a successful MR-compatible robot application can be built. A number of MR-compatible robots, ranging from a simple manipulator to a fully automated system, have been developed, proposing ingenious solutions to the design challenge. Several systems have been already tested clinically for prostate biopsy and brachytherapy. As technology matures, precise image guidance for prostate interventions performed or assisted by specialized MR-compatible robotic devices may provide a uniquely accurate solution for guiding the intervention directly based on MR findings and feedback. Such an instrument would become a valuable clinical tool for biopsies directly targeting imaged tumor foci and delivering tumor-centered focal therapy. PMID:19512852

Design of an everting balloon to deploy a microendoscope to the fallopian tubes

NASA Astrophysics Data System (ADS)

Keenan, Molly; Howard, Caitlin; Tate, Tyler; McGuiness, Ian; Sauer-Budge, Alexis; Black, John; Utzinger, Urs; Barton, Jennifer K.

2016-02-01

The 5-year survival rate for ovarian cancer is only 45% largely due to lack of effective screening methods. Current methods include palpation, transvaginal ultrasound, and the CA-125 blood test. Finding disease reliably and at an early stage increase survival to 92%. We have designed and built a 0.7 mm endoscope for the early detection of ovarian cancer. Inserted transvaginally through the working channel of a hysteroscope, the falloposcope creates a minimally invasive procedure for the screening of high risk women. To improve the ease-of-use and safety of falloposcope deployment, we are working to create an everting balloon. Currently, the falloposcope would require a skilled user to operate due to the challenging anatomy of the fallopian tubes - a small opening from the uterus (< 1 mm), tortuous path, and delicate lumenal features. A balloon delivery system would gently open the fallopian tube and guide the falloposcope down the center of lumen. We show balloon design and discuss integration with the falloposcope prototype. We test possible mechanical damage to the tissue due to scraping, puncture, or overstretching. Successful introduction of the everting balloon to simplify falloposcope delivery could expand screening beyond specialized centers to smaller clinical locations.

Particle Morphology and Elemental Composition of Smoke Generated by Overheating Common Spacecraft Materials

NASA Technical Reports Server (NTRS)

Meyer, Marit E.

2015-01-01

Fire safety in the indoor spacecraft environment is concerned with a unique set of fuels which are designed to not combust. Unlike terrestrial flaming fires, which often can consume an abundance of wood, paper and cloth, spacecraft fires are expected to be generated from overheating electronics consisting of flame resistant materials. Therefore, NASA prioritizes fire characterization research for these fuels undergoing oxidative pyrolysis in order to improve spacecraft fire detector design. A thermal precipitator designed and built for spacecraft fire safety test campaigns at the NASA White Sands Test Facility (WSTF) successfully collected an abundance of smoke particles from oxidative pyrolysis. A thorough microscopic characterization has been performed for ten types of smoke from common spacecraft materials or mixed materials heated at multiple temperatures using the following techniques: SEM, TEM, high resolution TEM, high resolution STEM and EDS. Resulting smoke particle morphologies and elemental compositions have been observed which are consistent with known thermal decomposition mechanisms in the literature and chemical make-up of the spacecraft fuels. Some conclusions about particle formation mechanisms are explored based on images of the microstructure of Teflon smoke particles and tar ball-like particles from Nomex fabric smoke.

Day one sustainability

NASA Astrophysics Data System (ADS)

Orr, John; Ibell, Timothy; Evernden, Mark; Darby, Antony

2015-05-01

Emissions reductions targets for the UK set out in the Climate Change Act for the period to 2050 will only be achieved with significant changes to the built environment, which is currently estimated to account for 50% of the UK's carbon emissions. The socio-technological nature of Civil Engineering means that this field is uniquely placed to lead the UK through such adaptations. This paper discusses the importance of interdisciplinary teaching to produce multi-faceted team approaches to sustainable design solutions. Methods for measuring success in education are often not fit for purpose, producing good students but poor engineers. Real-world failures to apply sustainable design present a serious, difficult to detect, and ultimately economically negative situation. Techniques to replace summative examinations are presented and discussed, with the aim of enhancing core technical skills alongside those required for sustainable design. Finally, the role of our future engineers in policy-making is discussed. In addition to carbon, the provision of water and food will heavily influence the work of civil engineers in the coming decades. Leadership from civil engineers with the technical knowledge and social awareness to tackle these issues will be required. This provides both opportunities and challenges for engineering education in the UK.

Morpheus Vertical Test Bed Flight Testing

NASA Technical Reports Server (NTRS)

Hart, Jeremy; Devolites, Jennifer

2014-01-01

NASA's Morpheus Project has developed and tested a prototype planetary lander capable of vertical takeoff and landing, that is designed to serve as a testbed for advanced spacecraft technologies. The lander vehicle, propelled by a LOX/Methane engine and sized to carry a 500kg payload to the lunar surface, provides a platform for bringing technologies from the laboratory into an integrated flight system at relatively low cost. Morpheus onboard software is autonomous from ignition all the way through landing, and is designed to be capable of executing a variety of flight trajectories, with onboard fault checks and automatic contingency responses. The Morpheus 1.5A vehicle performed 26 integrated vehicle test flights including hot-fire tests, tethered tests, and two attempted freeflights between April 2011 and August 2012. The final flight of Morpheus 1.5A resulted in a loss of the vehicle. In September 2012, development began on the Morpheus 1.5B vehicle, which subsequently followed a similar test campaign culminating in free-flights at a simulated planetary landscape built at Kennedy Space Center's Shuttle Landing Facility. This paper describes the integrated test campaign, including successes and setbacks, and how the system design for handling faults and failures evolved over the course of the project.

Design of a New Superconducting Magnet System for High Strength Minimum-B Fields for ECRIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, D. Z.; Benitez, J. Y.; Hodgkinson, A.

A novel Mixed Axial and Radial field System (MARS) seeks to enhance the B fields inside the plasma chamber within the limits of a given conductor, thereby making it possible to raise the operating fields for Electron Cyclotron Resonance Ion Sources (ECRISs). The MARS concept consists of a hexagonally shaped closed-loop coil and a set of auxiliary solenoids. The application of MARS will be combined with a hexagonal plasma chamber to maximize the use of the radial fields at the chamber inner surfaces. Calculations using Opera's TOSCA-3D solver have shown that MARS can potentially generate up to 50% higher fieldsmore » and use of only about one half of the same superconducting wire, as compared with existing magnet designs in ECRISs. A MARS magnet system built with Nb 3 Sn coils could generate a high strength minimum-B field of maxima of ≥ 10 T on axis and ~6 T radially in an ECRIS plasma chamber. Following successful development, the MARS magnet system will be the best magnet scheme for the next generation of ECRISs. This paper will present the MARS concept, magnet design, prototyping a copper closed-loop coil, and discussions.« less

Design of a New Superconducting Magnet System for High Strength Minimum-B Fields for ECRIS

DOE PAGES

Xie, D. Z.; Benitez, J. Y.; Hodgkinson, A.; ...

2016-06-01

A novel Mixed Axial and Radial field System (MARS) seeks to enhance the B fields inside the plasma chamber within the limits of a given conductor, thereby making it possible to raise the operating fields for Electron Cyclotron Resonance Ion Sources (ECRISs). The MARS concept consists of a hexagonally shaped closed-loop coil and a set of auxiliary solenoids. The application of MARS will be combined with a hexagonal plasma chamber to maximize the use of the radial fields at the chamber inner surfaces. Calculations using Opera's TOSCA-3D solver have shown that MARS can potentially generate up to 50% higher fieldsmore » and use of only about one half of the same superconducting wire, as compared with existing magnet designs in ECRISs. A MARS magnet system built with Nb 3 Sn coils could generate a high strength minimum-B field of maxima of ≥ 10 T on axis and ~6 T radially in an ECRIS plasma chamber. Following successful development, the MARS magnet system will be the best magnet scheme for the next generation of ECRISs. This paper will present the MARS concept, magnet design, prototyping a copper closed-loop coil, and discussions.« less

Design and qualification of the interferometer for the GOSAT-2 spectrometer

NASA Astrophysics Data System (ADS)

Montembault, Yan; Moreau, Louis; Roux, Michel; Buijs, Henry; Soucy, Marc-André

2016-10-01

GOSAT-2 is the successor of the Greenhouse gases Observing SATellite (GOSAT, "IBUKI") launched in 2009 by Japan Aerospace Exploration Agency (JAXA). GOSAT-2 will continue and enhance space borne measurements of greenhouse gases started by GOSAT and monitor the impacts of climate change and human activities on the carbon cycle. It will also contribute to climate science and climate change related policies. The GOSAT-2 spacecraft will carry two earth observation instruments: FTS-2, the second generation of the TANSO-FTS and CAI-2, a Cloud and Aerosol Imager. Mitsubishi Electric Corporation is the prime contractor of GOSAT-2. Harris is the subcontractor of the spectrometer. ABB, who successfully designed, manufactured, and delivered the interferometer for the TANSO-FTS instrument for GOSAT, is currently delivering the modulator for the FTS-2 instrument to Mitsubishi Electric Corporation. Built on the TANSO-FTS heritage, FTS-2 is a thermal and near infrared sensor for carbon observation based on a Fourier transform spectrometer featuring larger optical throughput than TANSO-FTS. This paper presents an overview of the design of the FTS-2 interferometer as well as key qualification and performance verification activities conducted on the interferometer flight model.

The positive effects of the FIRST high school robotics program

NASA Astrophysics Data System (ADS)

McIntyre, Nancy

The essence of the FIRST Robotics Program comes from the explanation of the acronym, which means For Inspiration and Recognition in Science and Technology. Their vision is to inspire young people, their schools, and communities, an appreciation of science and technology and an understanding that mastering these can enrich the lives of all. Last year I began our school's association with this program. I secured funding from NASA/JPL, attended a workshop and kickoff event, encouraged a team of students, parents, community members, and engineers to come together to design and construct a working, competitive robot in a six week time span. This year I expanded our participation to our 6th grade students. They competed in the FIRST Lego League. As part of my 9th grade science curriculum my students designed and built Panda II in class. The after-school team will submit a 30 second animation, an autocad design, and a team website for competition as well. Our AP art students have been charged with painting our travel crate. I couldn't have been successful without the help and support of a very dedicated JPL engineer who volunteers his time to come to our school to teach our team the technical components.

Noise and autism spectrum disorder in children: An exploratory survey.

PubMed

Kanakri, Shireen M; Shepley, Mardelle; Varni, James W; Tassinary, Louis G

2017-04-01

With more students being educated in schools for Autism Spectrum Disorder (ASD) than ever before, architects and interior designers need to consider the environmental features that may be modified to enhance the academic and social success of autistic students in school. This study explored existing empirical research on the impact of noise on children with ASD and provides recommendations regarding design features that can contribute to noise reduction. A survey, which addressed the impact of architectural design elements on autism-related behavior, was developed for teachers of children with ASD and distributed to three schools. Most teachers found noise control to be an important issue for students with autism and many observed children using ear defenders. In terms of managing issues related to noise, most teachers agreed that thick or soundproof walls and carpet in the classroom were the most important issues for children with ASD. Suggested future research should address architectural considerations for building an acoustically friendly environment for children with autism, identifying patterns of problematic behaviors in response to acoustical features of the built environment of the classroom setting, and ways to manage maladaptive behaviors in acoustically unfriendly environments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Toward a research and action agenda on urban planning/design and health equity in cities in low and middle-income countries.

PubMed

Smit, Warren; Hancock, Trevor; Kumaresen, Jacob; Santos-Burgoa, Carlos; Sánchez-Kobashi Meneses, Raúl; Friel, Sharon

2011-10-01

The importance of reestablishing the link between urban planning and public health has been recognized in recent decades; this paper focuses on the relationship between urban planning/design and health equity, especially in cities in low and middle-income countries (LMICs). The physical urban environment can be shaped through various planning and design processes including urban planning, urban design, landscape architecture, infrastructure design, architecture, and transport planning. The resultant urban environment has important impacts on the health of the people who live and work there. Urban planning and design processes can also affect health equity through shaping the extent to which the physical urban environments of different parts of cities facilitate the availability of adequate housing and basic infrastructure, equitable access to the other benefits of urban life, a safe living environment, a healthy natural environment, food security and healthy nutrition, and an urban environment conducive to outdoor physical activity. A new research and action agenda for the urban environment and health equity in LMICs should consist of four main components. We need to better understand intra-urban health inequities in LMICs; we need to better understand how changes in the built environment in LMICs affect health equity; we need to explore ways of successfully planning, designing, and implementing improved health/health equity; and we need to develop evidence-based recommendations for healthy urban planning/design in LMICs.

A stress sensor based on Galvanic Skin Response (GSR) controlled by ZigBee.

PubMed

Villarejo, María Viqueira; Zapirain, Begoña García; Zorrilla, Amaia Méndez

2012-01-01

Sometimes, one needs to control different emotional situations which can lead the person suffering them to dangerous situations, in both the medium and short term. There are studies which indicate that stress increases the risk of cardiac problems. In this study we have designed and built a stress sensor based on Galvanic Skin Response (GSR), and controlled by ZigBee. In order to check the device's performance, we have used 16 adults (eight women and eight men) who completed different tests requiring a certain degree of effort, such as mathematical operations or breathing deeply. On completion, we appreciated that GSR is able to detect the different states of each user with a success rate of 76.56%. In the future, we plan to create an algorithm which is able to differentiate between each state.

CSUNSat-1 CubeSat – ELaNa XVII

NASA Image and Video Library

2017-04-04

The primary mission of CSUNSat1 is to space test an innovative low temperature capable energy storage system developed by the Jet Propulsion Laboratory, raising its TRL level to 7 from 4 to 5. The success of this energy storage system will enable future missions, especially those in deep space to do more science while requiring less energy, mass and volume. This CubeSat was designed, built, programmed, and tested by a team of over 70 engineering and computer science students at CSUN.  The primary source of funding for CSUNSat1 comes from NASA’s Smallest Technology Partnership program. Launched by NASA’s CubeSat Launch Initiative on the NET April 18, 2017 ELaNa XVII mission on the seventh Orbital-ATK Cygnus Commercial Resupply Services (OA-7) to the International Space Station and deployed on tbd.

Low-Mass Inflation Systems for Inflatable Structures

NASA Technical Reports Server (NTRS)

Thunnissen, Daniel P.; Webster, Mark S.; Engelbrecht, Carl S.

1995-01-01

The use of inflatable space structures has often been proposed for aerospace and planetary applications. Communication, power generation, and very-long-baseline interferometry are just three potential applications of inflatable technology. The success of inflatable structures depends on the development of an applications of inflatable technology. This paper describes two design studies performed to develop a low mass inflation system. The first study takes advantage of existing onboard propulsion gases to reduce the overall system mass. The second study assumes that there is no onboard propulsion system. Both studies employ advanced components developed for the Pluto fast flyby spacecraft to further reduce mass. The study examined four different types of systems: hydrazine, nitrogen and water, nitrogen, and xenon. This study shows that all of these systems can be built for a small space structure with masses lower than 0.5 kilograms.

SULI Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clevenger, E.

2018-02-02

This project looks at alternative water sources, specifically in the field of desalination and selective ion removal through capacitive deionization (CDI). It project aims to both scale up the desalination capabilities of CDI cells as well as determine the selectivity of CDI for particular ions. My task is to design and build cells that have reproducible performance and characterize the materials for building these cells. The scientific methods I’ve learned through my work in CDI and the data mining and analysis tools I’ve become familiar with through CAES will be important catalysts in my future success in a graduate program.more » The purpose of this presentation is to give a standard of practice for my current method of building of capacitive deionization cells. Parts 1 and 2 will be discussed in which the electrodes are prepared, and the cell is built.« less

Promoting Healthy Workplaces by Building Cultures of Health and Applying Strategic Communications.

PubMed

Kent, Karen; Goetzel, Ron Z; Roemer, Enid C; Prasad, Aishwarya; Freundlich, Naomi

2016-02-01

The aim of the study was to identify key success elements of employer-sponsored health promotion (wellness) programs. We conducted an updated literature review, held discussions with subject matter experts, and visited nine companies with exemplary programs to examine current best and promising practices in workplace health promotion programs. Best practices include establishing a culture of health and using strategic communications. Key elements that contribute to a culture of health are leadership commitment, social and physical environmental support, and employee involvement. Strategic communications are designed to educate, motivate, market offerings, and build trust. They are tailored and targeted, multichanneled, bidirectional, with optimum timing, frequency, and placement. Increased efforts are needed to disseminate lessons learned from employers who have built cultures of health and excellent communications strategies and apply these insights more broadly in workplace settings.

CVD Fiber Coatings for Al2O3/NiAl Composites

NASA Technical Reports Server (NTRS)

Boss, Daniel E.

1995-01-01

While sapphire-fiber-reinforced nickel aluminide (Al2O3/NiAl) composites are an attractive candidate for high-temperature structures, the significant difference in the coefficient of thermal expansion between the NiAl matrix and the sapphire fiber creates substantial residual stresses in the composite. This study seeks to produce two fiber-coating systems with the potential to reduce the residual stresses in the sapphire/NiAl composite system. Chemical vapor deposition (CVD) was used to produce both the compensating and compliant-fiber coatings for use in sapphire/NiAl composites. A special reactor was designed and built to produce the FGM and to handle the toxic nickel precursors. This process was successfully used to produce 500-foot lengths of fiber with coating thicknesses of approximately 3 microns, 5 microns, and 10 microns.

Online polarimetry of the Nuclotron internal deuteron and proton beams

NASA Astrophysics Data System (ADS)

Isupov, A. Yu

2017-12-01

The spin studies at Nuclotron require fast and precise determination of the deuteron and proton beam polarization. For these purposes new powerful VME-based data acquisition (DAQ) system has been designed for the Deuteron Spin Structure setup placed at the Nuclotron Internal Target Station. The DAQ system is built using the netgraph-based data acquisition and processing framework ngdp. The software dealing with VME hardware is a set of netgraph nodes in form of the loadable kernel modules, so works in the operating system kernel context. The specific for current implementation nodes and user context utilities are described. The online events representation by ROOT classes allows us to generalize code for histograms filling and polarization calculations. The DAQ system was successfully used during 53rd and 54th Nuclotron runs, and their suitability for online polarimetry is demonstrated.

Potentiometric chip-based multipumping flow system for the simultaneous determination of fluoride, chloride, pH, and redox potential in water samples.

PubMed

Chango, Gabriela; Palacio, Edwin; Cerdà, Víctor

2018-08-15

A simple potentiometric chip-based multipumping flow system (MPFS) has been developed for the simultaneous determination of fluoride, chloride, pH, and redox potential in water samples. The proposed system was developed by using a poly(methyl methacrylate) chip microfluidic-conductor using the advantages of flow techniques with potentiometric detection. For this purpose, an automatic system has been designed and built by optimizing the variables involved in the process, such as: pH, ionic strength, stirring and sample volume. This system was applied successfully to water samples getting a versatile system with an analysis frequency of 12 samples per hour. Good correlation between chloride and fluoride concentration measured with ISE and ionic chromatography technique suggests satisfactory reliability of the system. Copyright © 2018 Elsevier B.V. All rights reserved.

Experimental setup for the study of resonant inelastic X-ray scattering of organometallic complexes in gas phase

NASA Astrophysics Data System (ADS)

Ismail, I.; Guillemin, R.; Marchenko, T.; Travnikova, O.; Ablett, J. M.; Rueff, J.-P.; Piancastelli, M.-N.; Simon, M.; Journel, L.

2018-06-01

A new setup has been designed and built to study organometallic complexes in gas phase at the third-generation Synchrotron radiation sources. This setup consists of a new homemade computer-controlled gas cell that allows us to sublimate solid samples by accurately controlling the temperature. This cell has been developed to be a part of the high-resolution X-ray emission spectrometer permanently installed at the GALAXIES beamline of the French National Synchrotron Facility SOLEIL. To illustrate the capabilities of the setup, the cell has been successfully used to record high-resolution Kα emission spectra of gas-phase ferrocene F e (C5H5) 2 and to characterize their dependence with the excitation energy. This will allow to extend resonant X-ray emission to different organometallic molecules.

Solid freeform fabrication of biomaterials

NASA Astrophysics Data System (ADS)

Chu, Tien-Min Gabriel

1999-12-01

The biological performance of porous Hydroxyapatite (HA) is closely related to the pore architecture in the implants. The study on the effect of architecture to the biological performance of porous HA requires new manufacturing methods that can fabricate implants with controlled pores channels. In this thesis, four highly loaded HA and alumina suspensions were formulated and three different processes involving Solid Freeform Fabrication (SFF) were developed. An aqueous HA suspension in acrylamides was first formulated and the UV-curing properties were evaluated. With a medical grade HA powder, two non-aqueous HA suspensions were formulated: a 40 vol.% HA suspension in Hexanediol Diacrylate (HDDA) and a 40 vol.% HA suspension in 1:1 mix of Propoxylated Neopentyl Glycol Diacrylate (PNPGDA) and Isobomyl Acrylate (EBA). A 50 vol.% Alumina suspension in PNPGDA/IBA was also formulated. The effect of dispersant to the viscosity of the suspensions was characterized. In the Stereolithography (SL) method, the curing parameters of HA/HDDA and HA/PNPGDA/IBA were determined. Prototype HA implants with 1,700 mum internal channels were built directly on an SL Apparatus (SLA). The designed internal channel patterns were preserved after sintering. In the Ink-jet printing method, the high temperature flow behaviors of the suspensions were characterized. The effects of solids loading to the viscosity of the suspensions were modeled with Krieger-Dougherty equation. Leveling theory developed in paint industry was employed to analyze the self-leveling capability of the suspensions. In the indirect SL method, the thermal curing behavior of HA and alumina suspensions were characterized. The total cure time was measured and the curing kinetics was modeled. Negative molds for the implants were designed and built on SLA with epoxy resin. HA/PNPGDA/IBA was cast into the mold and cured in an oven. The binders and the epoxy mold were pyrolyzed and the green bodies sintered. Internal channels with sizes in the range of 420 to 968 gm with standard deviation less than 50 mum were successfully built. The formulation and characterization techniques developed in this thesis were useful for evaluating the suspensions for SFF process. The manufacturing process developed in this thesis have provided new methods for controlling the channel size in porous HA implants.

Enhancing the Front-End Phase of Design Methodology

ERIC Educational Resources Information Center

Elias, Erasto

2006-01-01

Design methodology (DM) is defined by the procedural path, expressed in design models, and techniques or methods used to untangle the various activities within a design model. Design education in universities is mainly based on descriptive design models. Much knowledge and organization have been built into DM to facilitate design teaching.…

Little Red School House, New York City.

ERIC Educational Resources Information Center

Pearson, Clifford A.

2001-01-01

Discusses how architects successfully added a new 10,000 square-foot building, complete with glass-fronted library and skylit art room, to two existing structures built at different times and with different floor heights. Photos and a floorplan are included. (GR)

Built Environment Education Program Manual for Teachers and Architects.

ERIC Educational Resources Information Center

American Inst. of Architects, Sacramento, CA. California Council.

This teacher's handbook is designed to educate the city builders of tomorrow about the importance of responsible urban development. The activities stress the relationship between the built and natural environment. The goals of the project emphasize: (1) sensitivity to the importance of working in greater harmony with the total environment; (2)…

A telepresence robot system realized by embedded object concept

NASA Astrophysics Data System (ADS)

Vallius, Tero; Röning, Juha

2006-10-01

This paper presents the Embedded Object Concept (EOC) and a telepresence robot system which is a test case for the EOC. The EOC utilizes common object-oriented methods used in software by applying them to combined Lego-like software-hardware entities. These entities represent objects in object-oriented design methods, and they are the building blocks of embedded systems. The goal of the EOC is to make the designing embedded systems faster and easier. This concept enables people without comprehensive knowledge in electronics design to create new embedded systems, and for experts it shortens the design time of new embedded systems. We present the current status of a telepresence robot created with second-generation Atomi-objects, which is the name for our implementation of the embedded objects. The telepresence robot is a relatively complex test case for the EOC. The robot has been constructed using incremental device development, which is made possible by the architecture of the EOC. The robot contains video and audio exchange capability and a controlling system for driving with two wheels. The robot is built in two versions, the first consisting of a PC device and Atomi-objects, and the second consisting of only Atomi-objects. The robot is currently incomplete, but most of it has been successfully tested.

Optimization of critical quality attributes in continuous twin-screw wet granulation via design space validated with pilot scale experimental data.

PubMed

Liu, Huolong; Galbraith, S C; Ricart, Brendon; Stanton, Courtney; Smith-Goettler, Brandye; Verdi, Luke; O'Connor, Thomas; Lee, Sau; Yoon, Seongkyu

2017-06-15

In this study, the influence of key process variables (screw speed, throughput and liquid to solid (L/S) ratio) of a continuous twin screw wet granulation (TSWG) was investigated using a central composite face-centered (CCF) experimental design method. Regression models were developed to predict the process responses (motor torque, granule residence time), granule properties (size distribution, volume average diameter, yield, relative width, flowability) and tablet properties (tensile strength). The effects of the three key process variables were analyzed via contour and interaction plots. The experimental results have demonstrated that all the process responses, granule properties and tablet properties are influenced by changing the screw speed, throughput and L/S ratio. The TSWG process was optimized to produce granules with specific volume average diameter of 150μm and the yield of 95% based on the developed regression models. A design space (DS) was built based on volume average granule diameter between 90 and 200μm and the granule yield larger than 75% with a failure probability analysis using Monte Carlo simulations. Validation experiments successfully validated the robustness and accuracy of the DS generated using the CCF experimental design in optimizing a continuous TSWG process. Copyright © 2017 Elsevier B.V. All rights reserved.

A study on the flow characteristics of a direct drive turbine for energy conversion generation by experiment and CFD

NASA Astrophysics Data System (ADS)

Cho, Y. J.; Zullah, M. A.; Faizal, M.; Choi, Y. D.; Lee, Y. H.

2012-11-01

A variety of technologies has been proposed to capture the energy from waves. Some of the more promising designs are undergoing demonstration testing at commercial scales. Due to the complexity of most offshore wave energy devices and their motion response in different sea states, physical tank tests are common practice for WEC design. Full scale tests are also necessary, but are expensive and only considered once the design has been optimized. Computational Fluid Dynamics (CFD) is now recognized as an important complement to traditional physical testing techniques in offshore engineering. Once properly calibrated and validated to the problem, CFD offers a high density of test data and results in a reasonable timescale to assist with design changes and improvements to the device. The purpose of this study is to investigate the performance of a newly developed direct drive hydro turbine (DDT), which will be built in a caisson for extraction of wave energy. Experiments and CFD analysis are conducted to clarify the turbine performance and internal flow characteristics. The results show that commercial CFD code can be applied successfully to the simulation of the wave motion in the water tank. The performance of the turbine for wave energy converter is studied continuously for a ongoing project.

Research on Skin Cancer–Related Behaviors and Outcomes in the NIH Grant Portfolio, 2000-2014

PubMed Central

Dwyer, Laura A.; Tesauro, Gina; Taber, Jennifer M.; Norton, Wynne E.; Hartman, Anne M.; Geller, Alan C.

2017-01-01

Importance The Surgeon General’s Call to Action to Prevent Skin Cancer broadly identified research gaps, but specific objectives are needed to further behavioral intervention research. Objective To review National Institute of Health (NIH) grants targeting skin cancer–related behaviors and relevant outcomes. Design, Setting, and Participants A portfolio analysis of the title, abstract, specific aims, and research plans of identified grant applications from 2000 to 2014 targeting skin cancer–related behaviors or testing behavioral intervention effects on cancer-relevant outcomes along the cancer continuum. Main Outcomes and Measures Funding trends were compared along the cancer control continuum, with respect to investigator demographics and use of theory, technology, policy, and changes to environmental surroundings (built environment). Results A total of 112 submitted applications met inclusion criteria; of these, 40 (35.7%) were funded, and 31 of the 40 were interventions. Comparing the 40 funded grants with the 72 unfunded grants, the overall success rates did not differ significantly between male (33.3%) and female (37.3%) investigators, nor did the frequency of R01 awards (36.7% and 28.1%, respectively). Among intervention awards, most (24 of 31) addressed prevention. Fewer awards targeted detection alone or in conjunction with prevention (3) or cancer survivorship (4), and no grant addressed emotional sequelae or adherence behavior related to diagnosis or treatment. Fewer than half of funded grants aimed for clinically related targets (eg, sunburn reduction). Use of theory and technology occurred in more than 75% of grants. However, the full capability of proposed technology was infrequently used, and rarely did constructs of the proposed behavior change theory clearly and comprehensively drive the intervention approach. Policy or environmental manipulation was present in all dissemination grants but was rarely used elsewhere, and 19.4% included policy implementation and 25.8% proposed changes in built environment. Conclusions and Relevance Grant success rate in skin cancer–related behavioral science compares favorably to the overall NIH grant success rate (approximately 18%), and the success rate of male and female investigators was not statistically different. However, gaps exist in behavioral research addressing all points of the skin cancer control continuum, measuring interventions that hit clinically related targets, and leveraging technology, theory, and environmental manipulation to optimize intervention approach. PMID:28329179

High speed systems for time-resolved experiments with synchrotron radiation

NASA Astrophysics Data System (ADS)

Koziol, Anna; Maj, Piotr

2018-02-01

The UFXC32k is a single photon counting hybrid pixel detector with 75 μm pixel pitch. It was designed to cope with high X-ray intensities and therefore it is a very good candiate for synchrotron applications. In order to use this detector in an application, a dedicated setup must be designed and built allowing proper operation of the detector within the experiment. The paper presents two setups built for the purpose of Pump-Probe-Probe experiments at the Synchrotron SOLEIL and XPCS experiments at the APS.

Final Technical Report for Automated Manufacturing of Innovative CPV/PV Modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okawa, David

Cogenra’s Dense Cell Interconnect system was designed to use traditional front-contact cells and string them together into high efficiency and high reliability “supercells”. This novel stringer allows one to take advantage of the ~100 GW/year of existing cell production capacity and create a solar product for the customer that will produce more power and last longer than traditional PV products. The goal for this program was for Cogenra Solar to design and develop a first-of-kind automated solar manufacturing line that produces strings of overlapping cells or “supercells” based on Cogenra’s Dense Cell Interconnect (DCI) technology for their Low Concentration Photovoltaicmore » (LCPV) systems. This will enable the commercialization of DCI technology to improve the efficiency, reliability and economics for their Low Concentration Photovoltaic systems. In this program, Cogenra Solar very successfully designed, developed, built, installed, and started up the ground-breaking manufacturing tools required to assemble supercells. Cogenra then successfully demonstrated operation of the integrated line at high yield and throughput far exceeding expectations. The development of a supercell production line represents a critical step toward a high volume and low cost Low Concentration Photovoltaic Module with Dense Cell Interconnect technology and has enabled the evaluation of the technology for reliability and yield. Unfortunately, performance and cost headwinds on Low Concentration Photovoltaics systems including lack of diffuse capture (10-15% hit) and more expensive tracker requirements resulted in a move away from LCPV technology. Fortunately, the versatility of Dense Cell Interconnect technology allows for application to flat plate module technology as well and Cogenra has worked with the DOE to utilize the learning from this grant to commercialize DCI technology for the solar market through the on-going grant: Catalyzing PV Manufacturing in the US With Cogenra Solar’s Next-Generation Dense Cell Interconnect PV Module Manufacturing Technology. This program is now very successfully building off of this work and commercializing the technology to enable increased solar adoption.« less

SU-E-I-24: Design and Fabrication of a Multi-Functional Neck and Thyroid Phantom for Medical Dosimetry and Calibration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mehdizadeh, S; Sina, S; Karimipourfard, M

Purpose: The purpose of this study is the design and fabrication of a multipurpose anthropomorphic neck and thyroid phantom for use in medical applications (i.e. quality control of images in nuclear medicine, and dosimetry). Methods: The designed neck phantom is composed of seven elliptic cylindrical slices with semi-major axis of 14 and semi-minor axis of 12.5 cm, each having the thickness of 2cm. Thyroid gland, bony part of the neck, and the wind pipe were also built inside the neck phantom. Results: The phantom contains some removable plugs,inside and at its surface to accommodate the TLD chips with different shapesmore » and dimensions, (i.e. rod, cylindrical and cubical TLD chips)for the purpose of medical dosimetry (i.e. in radiology, radiotherapy, and nuclear medicine). For the purpose of quality control of images in nuclear medicine, the removable thyroid gland was built to accommodate the radioactive iodine. The female and male thyroid glands were built in two sizes separately. Conclusion: The designed phantom is a multi-functional phantom which is applicable for dosimetry in diagnostic radiology, radiotherapy, and quality control of images in nuclear medicine.« less

Evidence and speculation: reimagining approaches to architecture and research within the paediatric hospital.

PubMed

McLaughlan, Rebecca; Pert, Alan

2017-11-25

As the dominant research paradigm within the construction of contemporary healthcare facilities, evidence-based design (EBD) will increasingly impact our expectations of what hospital architecture should be. Research methods within EBD focus on prototyping incremental advances and evaluating what has already been built. Yet medical care is a rapidly evolving system; changes to technology, workforce composition, patient demographics and funding models can create rapid and unpredictable changes to medical practice and modes of care. This dynamism has the potential to curtail or negate the usefulness of current best practice approaches. To imagine new directions for the role of the hospital in society, or innovative ways in which the built environment might support well-being, requires a model that can project beyond existing constraints. Speculative design employs a design-based research methodology to imagine alternative futures and uses the artefacts created through this process to enable broader critical reflection on existing practices. This paper examines the contribution of speculative design within the context of the paediatric hospital as a means of facilitating critical reflection regarding the design of new healthcare facilities. While EBD is largely limited by what has already been built, speculative design offers a complementary research method to meet this limitation. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Evaluation of the NASA Arc Jet Capabilities to Support Mission Requirements

NASA Technical Reports Server (NTRS)

Calomino, Anthony; Bruce, Walt; Gage, Peter; Horn, Dennis; Mastaler, Mike; Rigali, Don; Robey, Judee; Voss, Linda; Wahlberg, Jerry; Williams, Calvin

2010-01-01

NASA accomplishes its strategic goals through human and robotic exploration missions. Many of these missions require launching and landing or returning spacecraft with human or return samples through Earth's and other planetary atmospheres. Spacecraft entering an atmosphere are subjected to extreme aerothermal loads. Protecting against these extreme loads is a critical element of spacecraft design. The safety and success of the planned mission is a prime concern for the Agency, and risk mitigation requires the knowledgeable use of thermal protection systems to successfully withstand the high-energy states imposed on the vehicle. Arc jets provide ground-based testing for development and flight validation of re-entry vehicle thermal protection materials and are a critical capability and core competency of NASA. The Agency's primary hypersonic thermal testing capability resides at the Ames Research Center and the Johnson Space Center and was developed and built in the 1960s and 1970s. This capability was critical to the success of Apollo, Shuttle, Pioneer, Galileo, Mars Pathfinder, and Orion. But the capability and the infrastructure are beyond their design lives. The complexes urgently need strategic attention and investment to meet the future needs of the Agency. The Office of Chief Engineer (OCE) chartered the Arc Jet Evaluation Working Group (AJEWG), a team of experienced individuals from across the Nation, to capture perspectives and requirements from the arc jet user community and from the community that operates and maintains this capability and capacity. This report offers the AJEWG's findings and conclusions that are intended to inform the discussion surrounding potential strategic technical and investment strategies. The AJEWG was directed to employ a 30-year Agency-level view so that near-term issues did not cloud the findings and conclusions and did not dominate or limit any of the strategic options.

Promoting Learning of Instructional Design via Overlay Design Tools

ERIC Educational Resources Information Center

Carle, Andrew Jacob

2012-01-01

I begin by introducing Virtual Design Apprenticeship (VDA), a learning model--built on a solid foundation of education principles and theories--that promotes learning of design skills via overlay design tools. In VDA, when an individual needs to learn a new design skill or paradigm she is provided accessible, concrete examples that have been…

SPRE 1 free-piston Stirling engine testing at NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Cairelli, James E.

1987-01-01

As part of the NASA funded portion of the SP-100 Advanced Technology Program the Space Power Research Engine (SPRE 1) was designed and built to serve as a research tool for evaluation and development of advanced Stirling engine concepts. The SPRE 1 is designed to produce 12.5 kW electrical power when operated with helium at 15 MPa and with an absolute temperature ratio of two. The engine is now under test in a new test facility which was designed and built at NASA Lewis specifically to test the SPRE 1. The SPRE 1, the NASA test facility, the initial SPRE 1 test results, and future SPRE 1 test plans are described.

Vision-The Strategic Leader Imperative

DTIC Science & Technology

1998-05-07

Habits of Highly Effective People . New York: Simon and Schuster, 1989. Estes, Howell M., III. United States Space Command: Vision For 2020...James C. and Jerry I. Porras. Built to Last: Successful Habits of Visionary Companies. New York: Harper Business, 1994. Covey, Stephen R. The 7

Pine Island Bay movie

Atmospheric Science Data Center

2014-08-01

... between successive frames is not uniform. The flow of the glacier, widening of the rift, and subsequent break-off of the iceberg are ... a gap in image acquisition during Antarctic winter, when the glacier was in continuous darkness. MISR was built and is managed by NASA's ...

Built-up Land Expansion in Urban China

NASA Astrophysics Data System (ADS)

Chen, Yi; Chen, Zhigang; Huang, Xianjin

2017-04-01

Since the implementation of the reform and opening-up, rapid expansion of built-up land has caused a rapid reduction of arable land. The Ministry of Land and Resources of the People' s Republic of China has strengthened the management of built-up land through the basic arable land protection and the quota allocation of built-up land to control the urban sprawl. In addition, the general land use planning and the annual land use plan have been used to further ensure the effectiveness of land use management and control. However, the trend of built-up land expansion has not been effectively restrained. The built-up land expansion increased from 31.92 × 106 hm2 in 2005 to 38.89 × 106 hm2 in 2012. The rapid expansion of built-up land has been the major feature of land use changes in China and has led to built-up land vacancy and inefficient land use. This paper used a Data Envelopment Analysis (DEA) model to analyze the changes in built-up land efficiency in 336 cities in China from 2005 to 2012 during the implementation of National General Land Use Plan (2006-2020) (NGLUP). The results showed that the built-up land input-output efficiency of most cities declined, and more than half of the cities had excessive inputs of built-up land. Even in the most developed region of China, the built-up land efficiency was relatively low. The paper argues that the NGLUP failed to control the expansion of built-up land and to promote intensive land use. The allocation of built-up land designated by the Plan was not reasonable, and economic development has greatly relied on land inputs, which need to be improved. The paper finally suggests that the built-up land indices should be appropriately directed toward economically underdeveloped regions in central and western China, and the establishment of a withdrawal mechanism for inefficient land would better promote the efficient allocation of built-up land.

Design Elements and Feasibility of an Organized Multiplayer Mobile Active Videogame for Primary School-Aged Children.

PubMed

McKenzie, Sophie; Bangay, Shaun; Barnett, Lisa M; Ridgers, Nicola D; Salmon, Jo

2014-12-01

This article describes the design, development, and implementation feasibility of a purpose-built mobile active videogame (M-AVG) named "Pirate Adventure," which was designed for primary school-aged children to engage in physical activity (PA) and fundamental movement skills (FMS), such as hopping, sidestepping, jumping, or running, in an afterschool setting. The design of "Pirate Adventure" was the result of a collaboration between games designers and health researchers. "Pirate Adventure" was designed and developed using Android(®) (Google, Mountain View, CA) phone sensors to respond to player actions within a playground environment. Using an interactive game framework, players solve clues and complete PA and FMS challenges via sensing the physical world through marked-out key game locations. Fourteen primary school-aged children participated in the feasibility evaluation, which took place in four afternoon sessions. The game was evaluated using Android phone telemetry data and a post-gameplay survey for children on their opinions and enjoyment of the game. The "Pirate Adventure" game design facilitated an enjoyable treasure hunt game (average of 11 minutes of activity per game) with narrative elements supporting children's engagement with movement activities. The majority of children (n=9/13) reported that they would like to play the game again. Combining real world and virtual world content through "Pirate Adventure" was moderately successful, with multiple gameplay sessions occurring. Further implementation feasibility testing, under more controlled conditions, needs to be conducted to assert the benefits of using a M-AVG for children's PA and FMS.

Demonstration of Metabolic Heat Regenerated Temperature Swing Adsorption Technology

NASA Technical Reports Server (NTRS)

Paul, Heather; Iacomini, Christine; Powers, Aaron; Dunham, Jonah; Straub-Lopez, Katie; Anerson, Grant; MacCallum, Taber

2007-01-01

Patent-pending Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is currently being investigated for removal and rejection of CO2 and heat from a Portable Life Support System (PLSS) to a Martian environment. The metabolically-produced CO2 present in the vent loop gas is collected using a CO2 selective adsorbent that has been cooled via a heat exchanger to near CO2 sublimation temperatures (approx.195K) with liquid CO2 obtained from Martian resources. Once the adsorbent is fully loaded, fresh warm, moist vent loop (approx.300K) is used to heat the adsorbent via another heat exchanger. The adsorbent will then reject the collected CO2 to the Martian ambient. Two beds are used to achieve continuous CO2 removal by cycling between the cold and warm conditions for adsorbent loading and regeneration, respectively. Small experiments have already been completed to show that an adsorbent can be cycled between these PLSS operating conditions to provide adequate conditions for CO2 removal from a simulated vent loop. One of the remaining technical challenges is extracting enough heat from the vent loop to warm the adsorbent in an appreciable time frame to meet the required adsorb/desorb cycle. The other key technical aspect of the technology is employing liquid CO2 to achieve the appropriate cooling. A technology demonstrator has been designed, built and tested to investigate the feasibility of 1) warming the adsorbent using the moist vent loop, 2) cooling the adsorbent using liquid CO2, and 3) using these two methods in conjunction to successfully remove CO2 from a vent loop and reject it to Mars ambient. Both analytical and numerical methods were used to perform design calculations and trades. The demonstrator was built and tested. The design analysis and testing results are presented along with recommendations for future development required to increase the maturity of the technology.

TRMM Solar Array

NASA Technical Reports Server (NTRS)

1996-01-01

Basic requirement of 978.59 watts per Panel output @ 58.9 volts B.O.L. was met on an average basis per agreement with NASA. Lower grade Cells were used on the shadowed Panel (Boom shadow) to maximize available power to the Spacecraft. The average output @ 58.9 volts was 991 watts. The outputs of the four t4) Panels ranged from 960 to 1,022 watts. The Panels successfully passed environmental testing at TRW to the contract specification and subsequent testing at NASA which involved output measurements at elevated temperatures. As this type of Array had never previously been built by TRW (aluminum Substrate with 4 cm x 4.4 cm GaAs Cells), the TRMM Program was a development effort combined with a Qual and Flight production effort. The most significant technical problem was Cell cracking during Qual thermal cycling. The cracking problem was determined to be generic within our Solar Array factory in the application of GaAs Cells to our designs. As a result, a TRW funded manufacturing process verification panel (known as the Manufacturing Verification Panel) was built to demonstrate our ability to properly apply GaAs Cells. The original Qual Panel comprised three (3) design variations with respect to Coverglass-to-Cell and Cell-to-Substrate adhesives. The intent was to qualify multiple designs in case one or more failed. When two of the three combinations failed due to excessive Cell breakage during thermal cycling, NASA was reluctant to allow Flight production based on the one remaining good Qual Panel Quadrant. This issue was pivotal for continuing the contract. Facts and recommendations are as follows: (1) The cause of the excessive cracking was never determined. and (2) The areas where the excessive cracking occurred utilized DC93-500 glassing adhesive which was NASA approved, and had been widely used by TRW on a multitude of projects.

Parameters affecting of Akkuyu's safety assessment for severe core damages

NASA Astrophysics Data System (ADS)

Kavun, Yusuf; Karasulu, Muzaffer

2015-07-01

We have looked at all past core meltdowns (Three Mile Island, Chernobyl and Fukushima incidents) and postulated the fourth one might be taking place in the future most probably in a newly built reactors anywhere of the earth in any type of NPP. The probability of this observation is high considering the nature of the machine and human interaction. Operation experience is a very significant parameter as well as the safety culture of the host nation. The concerns is not just a lack of experience with industry with the new comers, but also the infrastructure and established institutions who will be dealing with the Emergencies. Lack of trained and educated Emergency Response Organizations (ERO) is a major concern. The culture on simple fire drills even makes the difference when a severe condition occurs in the industry. The study assumes the fourth event will be taking place at the Akkuyu NGS and works backwards as required by the "what went wrong " scenarios and comes up with interesting results. The differences studied in depth to determine the impact to the severe accidents. The all four design have now core catchers. We have looked at the operator errors'like in TMI); Operator errors combined with design deficiencies(like in Chernobyl) and natural disasters( like in Fukushima) and found operator errors to be more probable event on the Akkuyu's postulated next incident. With respect to experiences of the operators we do not have any data except for long and successful operating history of the Soviet design reactors up until the Chernobyl incident. Since the Akkuyu will be built, own and operated by the Russians we have found no alarming concerns at the moment. At the moment, there is no body be able to operate those units in Turkey. Turkey is planning to build the required manpower during the transition period. The resolution of the observed parameters lies to work and educate, train of the host nation and exercise together.

SPRITE: A TPS Test Bed for Ground and Flight

NASA Technical Reports Server (NTRS)

Prabhu, Dinesh K.; Agrawal, Parul; Peterson, Keith; Swanson, Gregory; Skokova, Kristina; Mangini, Nancy; Empey, Daniel M.; Gorbunov, Sergey; Venkatapathy, Ethiraj

2012-01-01

Engineers in the Entry Systems and Technology Division at NASA Ames Research Center developed a fully instrumented, small atmospheric entry probe called SPRITE (Small Probe Reentry Investigation for TPS Engineering). SPRITE, conceived as a flight test bed for thermal protection materials, was tested at full scale in an arc-jet facility so that the aerothermal environments the probe experiences over portions of its flight trajectory and in the arc-jet are similar. This ground-to-flight traceability enhances the ability of mission designers to evaluate margins needed in the design of thermal protection systems (TPS) of larger scale atmospheric entry vehicles. SPRITE is a 14-inch diameter, 45 deg. sphere-cone with a conical aftbody and designed for testing in the NASA Ames Aerodynamic Heating Facility (AHF). The probe is a two-part aluminum shell with PICA (phenolic impregnated carbon ablator) bonded on the forebody and LI-2200 (Shuttle tile material) bonded to the aftbody. Plugs with embedded thermocouples, similar to those installed in the heat shield of the Mars Science Laboratory (MSL), and a number of distributed sensors are integrated into the design. The data from these sensors are fed to an innovative, custom-designed data acquisition system also integrated with the test article. Two identical SPRITE models were built and successfully tested in late 2010-early 2011, and the concept is currently being modified to enable testing of conformable and/or flexible materials.

Configuration of electro-optic fire source detection system

NASA Astrophysics Data System (ADS)

Fabian, Ram Z.; Steiner, Zeev; Hofman, Nir

2007-04-01

The recent fighting activities in various parts of the world have highlighted the need for accurate fire source detection on one hand and fast "sensor to shooter cycle" capabilities on the other. Both needs can be met by the SPOTLITE system which dramatically enhances the capability to rapidly engage hostile fire source with a minimum of casualties to friendly force and to innocent bystanders. Modular system design enable to meet each customer specific requirements and enable excellent future growth and upgrade potential. The design and built of a fire source detection system is governed by sets of requirements issued by the operators. This can be translated into the following design criteria: I) Long range, fast and accurate fire source detection capability. II) Different threat detection and classification capability. III) Threat investigation capability. IV) Fire source data distribution capability (Location, direction, video image, voice). V) Men portability. ) In order to meet these design criteria, an optimized concept was presented and exercised for the SPOTLITE system. Three major modular components were defined: I) Electro Optical Unit -Including FLIR camera, CCD camera, Laser Range Finder and Marker II) Electronic Unit -including system computer and electronic. III) Controller Station Unit - Including the HMI of the system. This article discusses the system's components definition and optimization processes, and also show how SPOTLITE designers successfully managed to introduce excellent solutions for other system parameters.

Designing for Change: Minimizing the Impact of Changing Requirements in the Later Stages of a Spaceflight Software Project

NASA Technical Reports Server (NTRS)

Allen, B. Danette

1998-01-01

In the traditional 'waterfall' model of the software project life cycle, the Requirements Phase ends and flows into the Design Phase, which ends and flows into the Development Phase. Unfortunately, the process rarely, if ever, works so smoothly in practice. Instead, software developers often receive new requirements, or modifications to the original requirements, well after the earlier project phases have been completed. In particular, projects with shorter than ideal schedules are highly susceptible to frequent requirements changes, as the software requirements analysis phase is often forced to begin before the overall system requirements and top-level design are complete. This results in later modifications to the software requirements, even though the software design and development phases may be complete. Requirements changes received in the later stages of a software project inevitably lead to modification of existing developed software. Presented here is a series of software design techniques that can greatly reduce the impact of last-minute requirements changes. These techniques were successfully used to add built-in flexibility to two complex software systems in which the requirements were expected to (and did) change frequently. These large, real-time systems were developed at NASA Langley Research Center (LaRC) to test and control the Lidar In-Space Technology Experiment (LITE) instrument which flew aboard the space shuttle Discovery as the primary payload on the STS-64 mission.

Dynamic Response Analysis of an Icosahedron Shaped Lighter Than Air Vehicle

DTIC Science & Technology

2015-03-26

Montgolfier brothers successfully achieved flight using a hot - air balloon . While this was not the first time a LTAV had been imagined, it was the...first time one had been successfully built and flown [3]. Hot - air balloons are able to stay afloat in the atmosphere by displacing a volume of air ...These possibilities have already been exploited by LTAVs using a lifting gas (hydrogen, helium, hot air ), but those vehicles require storage for the gas

A Simple Rate Law Experiment Using a Custom-Built Isothermal Heat Conduction Calorimeter

ERIC Educational Resources Information Center

Wadso, Lars; Li, Xi.

2008-01-01

Most processes (whether physical, chemical, or biological) produce or consume heat: measuring thermal power (the heat production rate) is therefore a typical method of studying processes. Here we describe the design of a simple isothermal heat conduction calorimeter built for use in teaching; we also provide an example of its use in simultaneously…

Learning Biology through Innovative Curricula: A Comparison of Game- and Nongame-Based Approaches

ERIC Educational Resources Information Center

Sadler, Troy D.; Romine, William L.; Menon, Deepika; Ferdig, Richard E.; Annetta, Leonard

2015-01-01

This study explored student learning in the context of innovative biotechnology curricula and the effects of gaming as a central element of the learning experience. The quasi-experimentally designed study compared learning outcomes between two curricular approaches: One built around a computer-based game, and the other built around a narrative…

Development, modeling, simulation, and testing of a novel propane-fueled Brayton-Gluhareff cycle acoustically-pressurized ramjet engine

NASA Astrophysics Data System (ADS)

Bramlette, Richard B.

In the 1950s, Eugene Gluhareff built the first working "pressure jet" engine, a variation on the classical ramjet engine with a pressurized inlet system relying on sonic tuning which allowed operation at subsonic speeds. The engine was an unqualified success. Unfortunately, after decades of sales and research, Gluhareff passed away leaving behind no significant published studies of the engine or detailed analysis of its operation. The design was at serious risk of being lost to history. This dissertation is intended to address that risk by studying a novel subscale modification of Gluhareff's original design operating on the same principles. Included is a background of related engine and how the pressure jet is distinct. The preliminary sizing of a pressure jet using closed-form expressions is then discussed followed by a review of propane oxidation modeling, how it integrates into the Computational Fluid Dynamics (CFD) solver, and the modeling of the pressure jet engine cycle with CFD. The simulation was matched to experimental data recorded on a purpose-built test stand recording chamber pressure, exhaust speed (via a Pitot/static system), temperatures, and thrust force. The engine CFD simulation produced a wide range of qualitative results that matched the experimental data well and suggested strong recirculation flows through the engine confirming suspicions about how the engine operates. Engine operating frequency between CFD and experiment also showed good agreement and appeared to be driven by the "Kadenacy Effect." The research effort lastly opens the door for further study of the engine cycle, the use of pressurized intakes to produce static thrust in a ramjet engine, the Gluhareff pressure jet's original geometry, and a wide array of potential applications. A roadmap of further study and applications is detailed including a modeling and testing of larger engines.

Mechanical Properties of Unreinforced Brick Masonry, Section1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mosalam, K; Glascoe, L; Bernier, J

2009-10-02

Before the advent of concrete and steel, masonry helped build civilizations. From Egypt in Africa, Rome in Europe, Maya in the America to China in Asia, masonry was exploited to construct the most significant, magnificent and long lasting structures on the Earth. Looking at the Egyptian pyramids, Mayan temples, Roman coliseum and Chinese Great Wall, one cannot stop wondering about the significance and popularity that masonry has had through out history. Lourenco et al (1989) summed up the reasons for the popularity of masonry in the following, 'The most important characteristic of masonry construction is its simplicity. Laying pieces ofmore » stone or bricks on top of each other, either with or without cohesion via mortar, is a simple, though adequate, technique that has been successful ever since remote ages. Other important characteristics are the aesthetics, solidity, durability, low maintenance, versatility, sound absorption and fire protection' Despite these advantages, masonry is no longer preferred structural material in many parts of the developed world, especially in seismically active parts of the world. Partly, masonry and especially unreinforced masonry (URM) has mechanical properties such as strength and ductility inferior to those of reinforced concrete and steel. Moreover, masonry structures were traditionally built based on rules of thumb acquired over many years of practice and/or empirical data from testing. Accordingly, we do not have a rigorous and uniform method of analysis and design for masonry. Nevertheless, the world still possesses numerous historic and ordinary masonry structures, which require maintenance and strengthening to combat the assault of time and nature. Hence, it is important to study fundamental properties of masonry so that new masonry structures can be effectively designed and built, and the cost for servicing old structures and for building new ones will be less expensive.« less

Students' construction of a simple steam distillation apparatus and development of creative thinking skills: A project-based learning

NASA Astrophysics Data System (ADS)

Diawati, Chansyanah; Liliasari, Setiabudi, Agus; Buchari

2017-05-01

This project-based learning combined the chemistry of separation process using steam distillation with engineering design process in an undergraduate chemistry course. Students built upon their knowledge of phase changes, immiscible mixture, and the relationship between vapor pressure and boiling point to complete a project of modifications steam distillation apparatus. The research method is a qualitative case study, which aims to describe how (1) the creative thinking skills of students emerged during six weeks of theproject, (2) students built steam distillation apparatus characteristics as the project product and (3) students response to the project-based learning model. The results showed that the students had successfully constructed a steam distillation apparatus using plastic kettle as steam generator and distillation flask. A Plastic tubewas used to drain water vapor from steam generator to distillation flask and to drain steam containing essential oil to the condenser. A biscuit tin filled with ice was used as a condenser. The time required until resulting distillate was fifteen minutes. The production of essential was conductive qualitatively by a very strong smell typical of essential oil and two phases of distillate. Throughout the project, students formulated the relevant and varied problem, formulated the goals, proposed the ideas of the apparatus and materials, draw apparatus design, constructed apparatus, tested apparatus, evaluated, and reported the project. Student response was generally positive. They were pleased, interested, more understanding the concepts and work apparatus principles, also implemented new ideas. These results indicate that project-based learning can develop students' creative thinking skills. Based on these results, it is necessary to conduct research and implemented project-based learning to other concepts.

Developing a Webcam-Based Data Logger to Analyze Cosmic Rays in a Cloud Chamber

NASA Astrophysics Data System (ADS)

Nealon, Kelly; Bellis, Matt

2015-04-01

Muons from secondary cosmic rays provide students with an opportunity to interact with a natural phenomenon that relies both on special relativity and fairly sophisticated particle physics knowledge. In many physics departments, undergraduate students set up a pair of scintillators in coincidence to measure the rate of these muons and in some cases, measure their angular dependence, but this requires specialized and potentially expensive equipment. We have spent the past year formalizing a design of a cloud chamber that relies not on dry ice, but Peltier thermoelectric coolers, that can be built for about one hundred dollars worth of equipment. With this design we can see the tracks left by cosmic rays, however to turn it into a useful undergraduate physics lab requires some sort of data logger. This poster details our efforts to use an off-the-shelf webcam to trigger on the change in image when a cosmic ray track appears in the chamber. We use this to estimate the rate and angular dependence and compare our results to other measurements. The successes and limitations of this approach will be discussed.

A policy model to initiate environmental negotiations: Three hydropower workshops

USGS Publications Warehouse

Lamb, Berton Lee; Taylor, Jonathan G.; Burkardt, Nina; Ponds, Phadrea D.

1998-01-01

How do I get started in natural resource negotiations? Natural resource managers often face difficult negotiations when they implement laws and policies regulating such resources as water, wildlife, wetlands, endangered species, and recreation. As a result of these negotiations, managers must establish rules, grant permits, or create management plans. The Legal‐Institutional Analysis Model (LIAM) was designed to assist managers in systematically analyzing the parties in natural resource negotiations and using that analysis to prepare for bargaining. The LIAM relies on the theory that organizations consistently employ behavioral roles. The model uses those roles to predict likely negotiation behavior. One practical use of the LIAM is when all parties to a negotiation conduct a workshop as a way to open the bargaining on a note of trust and mutual understanding. The process and results of three LIAM workshops designed to guide hydroelectric power licensing negotiations are presented. Our experience with these workshops led us to conclude that the LIAM can be an effective tool to begin a negotiation and that trust built through the workshops can help create a successful result.

Wavefront measurement of plastic lenses for mobile-phone applications

NASA Astrophysics Data System (ADS)

Huang, Li-Ting; Cheng, Yuan-Chieh; Wang, Chung-Yen; Wang, Pei-Jen

2016-08-01

In camera lenses for mobile-phone applications, all lens elements have been designed with aspheric surfaces because of the requirements in minimal total track length of the lenses. Due to the diffraction-limited optics design with precision assembly procedures, element inspection and lens performance measurement have become cumbersome in the production of mobile-phone cameras. Recently, wavefront measurements based on Shack-Hartmann sensors have been successfully implemented on injection-molded plastic lens with aspheric surfaces. However, the applications of wavefront measurement on small-sized plastic lenses have yet to be studied both theoretically and experimentally. In this paper, both an in-house-built and a commercial wavefront measurement system configured on two optics structures have been investigated with measurement of wavefront aberrations on two lens elements from a mobile-phone camera. First, the wet-cell method has been employed for verifications of aberrations due to residual birefringence in an injection-molded lens. Then, two lens elements of a mobile-phone camera with large positive and negative power have been measured with aberrations expressed in Zernike polynomial to illustrate the effectiveness in wavefront measurement for troubleshooting defects in optical performance.

A 3D cell culture system: separation distance between INS-1 cell and endothelial cell monolayers co-cultured in fibrin influences INS-1 cells insulin secretion.

PubMed

Sabra, Georges; Vermette, Patrick

2013-02-01

The aim of this study was to develop an in vitro cell culture system allowing studying the effect of separation distance between monolayers of rat insulinoma cells (INS-1) and human umbilical vein endothelial cells (HUVEC) co-cultured in fibrin over INS-1 cell insulin secretion. For this purpose, a three-dimensional (3D) cell culture chamber was designed, built using micro-fabrication techniques and validated. The co-culture was successfully carried out and the effect on INS-1 cell insulin secretion was investigated. After 48 and 72 h, INS-1 cells co-cultured with HUVEC separated by a distance of 100 µm revealed enhanced insulin secretion compared to INS-1 cells cultured alone or co-cultured with HUVEC monolayers separated by a distance of 200 µm. These results illustrate the importance of the separation distance between two cell niches for cell culture design and the possibility to further enhance the endocrine function of beta cells when this factor is considered. Copyright © 2012 Wiley Periodicals, Inc.

Design for validation: An approach to systems validation

NASA Technical Reports Server (NTRS)

Carter, William C.; Dunham, Janet R.; Laprie, Jean-Claude; Williams, Thomas; Howden, William; Smith, Brian; Lewis, Carl M. (Editor)

1989-01-01

Every complex system built is validated in some manner. Computer validation begins with review of the system design. As systems became too complicated for one person to review, validation began to rely on the application of adhoc methods by many individuals. As the cost of the changes mounted and the expense of failure increased, more organized procedures became essential. Attempts at devising and carrying out those procedures showed that validation is indeed a difficult technical problem. The successful transformation of the validation process into a systematic series of formally sound, integrated steps is necessary if the liability inherent in the future digita-system-based avionic and space systems is to be minimized. A suggested framework and timetable for the transformtion are presented. Basic working definitions of two pivotal ideas (validation and system life-cyle) are provided and show how the two concepts interact. Many examples are given of past and present validation activities by NASA and others. A conceptual framework is presented for the validation process. Finally, important areas are listed for ongoing development of the validation process at NASA Langley Research Center.

Optimizing DNA assembly based on statistical language modelling.

PubMed

Fang, Gang; Zhang, Shemin; Dong, Yafei

2017-12-15

By successively assembling genetic parts such as BioBrick according to grammatical models, complex genetic constructs composed of dozens of functional blocks can be built. However, usually every category of genetic parts includes a few or many parts. With increasing quantity of genetic parts, the process of assembling more than a few sets of these parts can be expensive, time consuming and error prone. At the last step of assembling it is somewhat difficult to decide which part should be selected. Based on statistical language model, which is a probability distribution P(s) over strings S that attempts to reflect how frequently a string S occurs as a sentence, the most commonly used parts will be selected. Then, a dynamic programming algorithm was designed to figure out the solution of maximum probability. The algorithm optimizes the results of a genetic design based on a grammatical model and finds an optimal solution. In this way, redundant operations can be reduced and the time and cost required for conducting biological experiments can be minimized. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Nucleic Acid Nanostructures: Bottom-Up Control of Geometry on the Nanoscale

PubMed Central

Seeman, Nadrian C.; Lukeman, Philip S.

2012-01-01

DNA may seem an unlikely molecule from which to build nanostructures, but this is not correct. The specificity of interaction that enables DNA to function so successfully as genetic material also enables its use as a smart molecule for construction on the nanoscale. The key to using DNA for this purpose is the design of stable branched molecules, which expand its ability to interact specifically with other nucleic acid molecules. The same interactions used by genetic engineers can be used to make cohesive interactions with other DNA molecules that lead to a variety of new species. Branched DNA molecules are easy to design, and the can assume a variety of structural motifs. These can be used for purposes both of specific construction, such as polyhedra, and for the assembly of topological targets. A variety of two-dimensional periodic arrays with specific patterns have been made. DNA nanomechanical devices have been built with a series of different triggers, small molecules, nucleic acid molecules and proteins. Recently, progress has been made in self-replication of DNA nano-constructs, and in the scaffolding of other species into DNA arrangements. PMID:25152542

WIYN tip-tilt module performance

NASA Astrophysics Data System (ADS)

Claver, Charles F.; Corson, Charles; Gomez, R. Richard, Jr.; Daly, Philip N.; Dryden, David M.; Abareshi, Behzod

2003-02-01

The WIYN Tip-Tilt Module (WTTM) is an addition to the existing Instrument Adapter System (IAS) providing a high performance optical-NIR image stabilized port on the WIYN 3.5m telescope. The WTTM optical system uses a 3-mirror off-axis design along with a high bandwidth tilt mirror. The WTTM is a reimaging system with 15% magnification producing a 4x4 arcminute field of view and near diffraction limited imagery from 400-2000nm. The optics are diamond turned in electroless Nickel over an Aluminum substrate. The WTTM opto-mechanical assembly was designed and built using the principals of the "build-to-print" technique, where the entire system is fabricated and assembled to tolerance with no adjustments. A unique high performance error sensor, using an internal mirrorlette array that feeds 4 fiber coupled avalanche photodiode photon counters, provides the tilt signal. The system runs under the Real-Time Linux operating system providing a maximum closed loop rate of 3khz. In this paper we report on the successful lab testing, verification of the "build-to-print" technique and on telescope performance of the WTTM.

A simple and accessible synthetic lectin for glucose recognition and sensing

NASA Astrophysics Data System (ADS)

Ke, Chenfeng; Destecroix, Harry; Crump, Matthew P.; Davis, Anthony P.

2012-09-01

Binding carbohydrates from water is a difficult task, even for the natural carbohydrate-binding proteins known as lectins. The design of synthetic lectin mimics is correspondingly challenging, especially if good selectivities are required. In previous work we showed that success is possible, but only for complex polycyclic architectures that require lengthy and low-yielding syntheses; for example, one glucose-selective system was made in 21 steps and only 0.1% overall yield. Here we report the discovery of a simple monocyclic host that matches the earlier designs, but is far more accessible as it is prepared in just five steps and 23% overall yield. The new synthetic lectin binds glucose with excellent selectivity versus other common monosaccharides (for example, ∼50:1 versus galactose) and sufficient affinity for glucose sensing at the concentrations found in blood. It also features a built-in signalling system in the form of strong and guest-dependent fluorescence emission. The effectiveness and simplicity of this molecule suggests the potential for development into a new methodology for practical glucose monitoring.

Active-matrix OLED using 150°C a-Si TFT backplane built on flexible plastic substrate

NASA Astrophysics Data System (ADS)

Sarma, Kalluri R.; Chanley, Charles; Dodd, Sonia R.; Roush, Jared; Schmidt, John; Srdanov, Gordana; Stevenson, Matthew; Wessel, Ralf; Innocenzo, Jeffrey; Yu, Gang; O'Regan, Marie B.; MacDonald, W. A.; Eveson, R.; Long, Ke; Gleskova, Helena; Wagner, Sigurd; Sturm, James C.

2003-09-01

Flexible displays fabricated using plastic substrates have a potential for being very thin, light weight, highly rugged with greatly minimized propensity for breakage, roll-to-roll manufacturing and lower cost. The emerging OLED display media offers the advantage of being a solid state and rugged structure for flexible displays in addition to the many potential advantages of an AM OLED over the currently dominant AM LCD. The current high level of interest in flexible displays is facilitating the development of the required enabling technologies which include development of plastic substrates, low temperature active matrix device and backplane fabrication, and display packaging. In the following we will first discuss our development efforts in the PEN based plastic substrates, active matrix backplane technology, low temperature (150°C) a-Si TFT devices and an AM OLED test chip used for evaluating various candidate designs. We will then describe the design, fabrication and successful evaluation and demonstration of a 64x64 pixel AM OLED test display using a-Si TFT backplane fabricated at 150°C on the flexible plastic substrate.

In-service and pre-service teacher education in IBSE: The ESTABLISH approach

NASA Astrophysics Data System (ADS)

Ješková, Zuzana; Kireš, Marián; McLoughlin, Eilish; Finlayson, Odilla; Ottander, Christina; Ekborg, Margareta

2016-05-01

One of the main goals of the ESTABLISH 7fp project (available on line at http://www.establish-fp7.eu/) was the development and implementation of the professional development teacher education programmes (TEP) to support teachers in adopting inquiry-based strategies in their teaching. Within the project there was a model for in-service and pre-service teacher training in IBSE designed and implemented across 12 participating countries. The programme is based on 4 core elements and 4 additional elements that are built around the IBSE teaching units developed within the project. As accepted by ESTABLISH partners, all teacher training programmes include the minimum of the four elements, i.e. introduction to IBSE, industrial content knowledge, teacher as implementer and teacher as developer of IBSE teaching materials. There are also four additional elements designed in detail, i.e. ICT for IBSE, argumentation in the classroom, research and design projects for students, assessment of IBSE. These can be added to the programme optionally with regard to the level of teachers' IBSE skills and current situation in education and teachers' professional development within the country. This ESTABLISH model of TEP was followed in participating countries in order to change teachers' attitudes from traditional ways of teaching towards adopting inquiry strategies and their successful implementation in the classroom. Within the face-to-face workshops teachers experienced and developed their inquiry based teaching strategies using specifically developed materials. In addition, the e-platform has been developed to provide on-line support. This platform provides educators and teachers with all the necessary materials for the training and IBSE teaching units and other teaching materials for teachers' ongoing help. The teacher training programme was successfully implemented in Slovakia. There were two runs of teacher training workshops on IBSE already carried out. Moreover, the additional element ICT in IBSE was developed more deeply designing a separate teacher training course for it. The contribution discusses in more details the success and problems of implementation in the context of Slovak educational environment.

Miniature Free-Flying Magnetometer Utilizing System-On-A-Chip Technology

NASA Technical Reports Server (NTRS)

Eyre, F. B.; Blaes, B. R.

2001-01-01

Four Free-Flying Magnetometers (FFMs), developed at the Jet Propulsion Laboratory (JPL) for the Enstrophy mission, were successfully deployed from the payload of a sounding rocket launched from Poker Flats, Alaska on February 11, 1999. The FFMs functioned successfully by synchronously measuring the vector magnetic field at 4 points separate from the payload and at relative distances up to 3 km, and communicated their data, in bursts, to the ground. This is the first time synchronized in-situ multipoint measurements of the Earth's magnetic field utilizing miniature spin-stabilized "sensorcraft" have been performed. The data they provided have enabled, for the first time, the direct measure of field-aligned current density and are enabling new science by determining the fine-scale structure of the currents in the Earth's ionosphere involved in the production of aurora. These proof-of-concept "hockey puck" (80 mm diameter, 38 mm height, 250 gram mass) FFMs were built using off-the-shelf commercial, industrial, and military grade surface-mount electronic components. Radiation-hard electronics was not required for the Enstrophy mission's short sub-orbital flight. The successful design, implementation, and flight demonstration of this 1st generation FFM design has provided a solid base for further development of a 2nd generation FFM design for planetary science applications. A reliable ultra-miniature radiation-hard 2nd-generation FFM utilizing System-On-A-Chip (SOAC) technologies is proposed. This design would be targeted for long-term planetary missions to investigate magnetospheric field configurations in regions having small-scale structure and to separate spatial and temporal variations. A fleet of short-lived (expendable) FFMs would be deployed into a targeted region to gather multiprobe vector magnetic field data. The FFMs would be ejected from a parent spacecraft at a speed of a few m/sec and would cover spatial volumes of order tens of kilometers for times of order one hour. The parent spacecraft would carry a sufficient number of FFMs for multiple deployments. Additional information is contained in the original extended abstract.

49 CFR 41.117 - Buildings built with Federal assistance.

Code of Federal Regulations, 2011 CFR

2011-10-01

... architect's authenticated verifications of seismic design codes, standards, and practices used in the design... financial assistance, after July 14, 1993 must be designed and constructed in accord with seismic standards... of compliance with the seismic design and construction requirements of this part is required prior to...

New asphalt mix design system for Oklahoma department of transportation : final report.

DOT National Transportation Integrated Search

2013-03-01

Oklahoma Department of Transportation (ODOT) has been using the Superpave mix design software for several years. The original Superpave mix design software was built around Fox Database and did not meet ODOT requirements. The software currently being...

A GIS based model for active transportation in the built environment

NASA Astrophysics Data System (ADS)

Addison, Veronica Marie Medina

Obesity and physical inactivity have been major risk factors associated with morbidity and mortality in the United States. Recently, obesity and physical inactivity have been on the rise. Determining connections between this trend and the environment could lead to a built environment that is conducive to healthy, active people. In my previous research, I have studied the built environment and its connection to health. For my dissertation, I build on this fundamental work by incorporating energy, specifically by studying the built environment and its connection to energy expenditures. This research models the built environment and combines this with human energy expenditure information in order to provide a planning tool that allows an individual to actively address health issues, particularly obesity. This research focuses on the design and development of an internet based model that enables individuals to understand their own energy expenditures in relation to their environment. The model will work to find the energy consumed by an individual in their navigation through campus. This is accomplished by using Geographic Information Systems (GIS) to model the campus and using it as the basis for calculating energy expended through active transportation. Using GIS to create the model allows for the incorporation of built environment factors such as elevation and energy expenditures in relation to physical exertion rate. This research will contribute to the long-term solution to the obesity epidemic by creating healthy communities through smart growth and sustainable design. This research provides users with a tool to use in their current environment for their personal and community well being.

Integrated learning of mathematics, science and technology concepts through LEGO/Logo projects

NASA Astrophysics Data System (ADS)

Wu, Lina

This dissertation examined integrated learning in the domains of mathematics, science and technology based on Piaget's constructivism, Papert's constructionism, and project-based approach to education. Ten fifth grade students were involved in a two-month long after school program where they designed and built their own computer-controlled LEGO/Logo projects that required the use of gears, ratios and motion concepts. The design of this study centered on three notions of integrated learning: (1) integration in terms of what educational materials/settings provide, (2) integration in terms of students' use of those materials, and (3) integration in the psychological sense. In terms of the first notion, the results generally showed that the LEGO/Logo environment supported the integrated learning of math, science and technology concepts. Regarding the second notion, the students all completed impressive projects of their own design. They successfully combined gears, motors, and LEGO parts together to create motion and writing control commands to manipulate the motion. But contrary to my initial expectations, their successful designs did not require numerical reasoning about ratios in designing effective gear systems. When they did reason about gear relationships, they worked with "qualitative" ratios, e.g., "a larger driver gear with a smaller driven gear increases the speed." In terms of the third notion of integrated learning, there was evidence in all four case study students of the psychological processes involved in linking mathematical, scientific, and/or technological concepts together to achieve new conceptual units. The students not only made connections between ideas and experiences, but also recognized decisive patterns and relationships in their project work. The students with stronger overall project performances showed more evidence of synthesis than the students with relatively weaker performances did. The findings support the conclusion that all three notions of the integrated learning are important for understanding what the students learned from their project work. By considering these notions together, and by deliberating about their interrelations, we take a step towards understanding the integrated learning.

Theo Jansen Project in Engineering Design Course and a Design Example

ERIC Educational Resources Information Center

Liu, Yucheng; Artigue, Aaron; Sommers, Jeremy; Chambers, Terence

2011-01-01

Objectives of a project-oriented mechanical engineering course, Engineering Design, were achieved through a design project, where students designed, built and demonstrated an extreme version of a basic Theo Jansen device. Through this project, junior students in the University of Louisiana fully developed the capability of applying mathematic and…

Inclusive Design: Developing Students' Knowledge and Attitude through Empathic Modelling

ERIC Educational Resources Information Center

Altay, Burçak; Demirkan, Halime

2014-01-01

To enhance the function and quality of built environments, designers should consider all possible users in their design projects. Therefore, it is essential to incorporate inclusive design in the education of the design student. This study focuses on the educational objectives of and related learning activities in a course where inclusive design…

Building Bridges to Diversity in Graduate Physics & Astronomy: The Fisk-Vanderbilt Masters-to-PhD Bridge Program

NASA Astrophysics Data System (ADS)

Stassun, Keivan G.

2006-12-01

We describe the Fisk-Vanderbilt Masters-to-PhD Bridge program as a successful model for effective partnerships with minority-serving institutions toward significantly broadening the participation of underrepresented groups in the physical sciences. The program couples targeted recruitment with active retention strategies, and is built upon a clearly defined structure that is flexible enough to address individual student needs while maintaining clearly communicated baseline standards for student performance. A key precept of the program’s philosophy is to eliminate passivity in student mentoring; students are deliberately groomed to successfully transition into the PhD program through active involvement in research experiences with future PhD advisers, coursework that demonstrates competency in core PhD subject areas, and frequent interactions with joint mentoring committees. This approach allows student progress and performance to be monitored and evaluated in a more holistic manner than usually afforded by limited metrics such as standardized tests. Since its inception in 2004, the program has attracted a total of 18 underrepresented students, with a retention rate of 90%. Recent research indicates that minority students are nearly twice as likely as non-minority students to seek a Masters degree en route to the PhD. In essence, the Bridge program described here builds upon this increasingly important pathway, with a dedicated mentoring process designed to ensure that the Masters-to-PhD transition is a successful one.

Designing for emotion (among other things)

PubMed Central

Gaver, William

2009-01-01

Using computational approaches to emotion in design appears problematic for a range of technical, cultural and aesthetic reasons. After introducing some of the reasons as to why I am sceptical of such approaches, I describe a prototype we built that tried to address some of these problems, using sensor-based inferencing to comment upon domestic ‘well-being’ in ways that encouraged users to take authority over the emotional judgements offered by the system. Unfortunately, over two iterations we concluded that the prototype we built was a failure. I discuss the possible reasons for this and conclude that many of the problems we found are relevant more generally for designs based on computational approaches to emotion. As an alternative, I advocate a broader view of interaction design in which open-ended designs serve as resources for individual appropriation, and suggest that emotional experiences become one of several outcomes of engaging with them. PMID:19884154

Managing Communication within Virtual Intercultural Teams.

ERIC Educational Resources Information Center

Grosse, Christine Uber

2002-01-01

Suggests that business students need to be prepared to manage the communication of intercultural teams. Discusses strategies for success such as: developing a network of good relationships built on trust and understanding; showing respect for other cultures and languages; and understanding how diversity strengthens the team. (SG)

Feel the Fear: Learning Graphic Design in Affective Places and Online Spaces

ERIC Educational Resources Information Center

Nottingham, Anitra

2017-01-01

This article explores the idea of pedagogic affect in both onsite and online graphic design learning spaces, and speculates on the role that this affect plays in the formation of the design student. I argue that embodied design knowledge is built by interactions with design professionals, activities that mimic the daily work of designers, and…

Design, Manufacture and Test of Cryotank Components

NASA Technical Reports Server (NTRS)

McCarville, Douglas A.; Guzman, Juan C.; Dillon. Alexandra K.; Jackson, Justin R.; Birkland, Jordan O.

2017-01-01

On the composite cryotank technology development (CCTD) project, the Boeing Company built two cryotanks as a means of advancing technology and manufacturing readiness levels (TRL and MRL) and lowering the risk of fabricating full-scale fuel containment vessels.1 CCTD focused on upper stage extended duration applications where long term storage of propellants is required. The project involved the design, analysis, fabrication, and test of manufacturing demonstration units (MDU), a 2.4 m (precursor) and a 5.5 m composite cryotank. Key design features included one-piece wall construction to minimize overall weight (eliminating the need for a bellyband joint), 3-dimensionally (3D) reinforced y-joint material to alleviate stress concentrations at the tank to skirt interface and a purge-able ?uted core skirt to carry high axial launch loads. The tanks were made with OoA curing pre-impregnated (prepreg) carbon/epoxy (C/E) slit-tape tow (STT) that contained thin micro-crack resistant plies in the tank wall center to impede permeation. The tanks were fabricated at Boeing's Seattle-based Advanced Development Center (ADC) using RAFP and multipiece break-down tooling. The tooling was designed and built by Janicki Industries (JI) at Sedro Woolley, Washington. Tank assemblage consisted of co-bonded dome covers, one-piece ?uted core skirts and mechanical fastened cover/sump. Ultrasonic inspection was performed after every cure or bond and a structural health monitoring system (SHMS) was installed to identify potential impact damage events (in-process and/or during transportation). The tanks were low temperature tested at NASA's George C. Marshall Space Flight Center (MSFC) in Huntsville, Alabama. The testing, which consisted of a sequence of ?ll/drain pressure and thermal cycles using LH2, was successfully concluded in 2012 on the 2.4 m tank and in 2014 on the 5.5 m tank. Structural, thermal, and permeation performance data was obtained. 2 Critical design features and manufacturing advancements, which helped to validate 25% weight and 30% cost reduction projections, were matured. These advancements will help to guide future composite tank integration activities on next generation long duration aircraft and space launch vehicles. Because CCTD addressed innovative design features, heavy lift size scale-up, multipiece captured tooling, new generation automated material placement (AMP) equipment and OoA materials, this chapter should be of interest to educators, students and manufacturers of composite hardware and ?ight vehicles.

External built residential environment characteristics that affect mental health of adults.

PubMed

Ochodo, Charles; Ndetei, D M; Moturi, W N; Otieno, J O

2014-10-01

External built residential environment characteristics include aspects of building design such as types of walls, doors and windows, green spaces, density of houses per unit area, and waste disposal facilities. Neighborhoods that are characterized by poor quality external built environment can contribute to psychosocial stress and increase the likelihood of mental health disorders. This study investigated the relationship between characteristics of external built residential environment and mental health disorders in selected residences of Nakuru Municipality, Kenya. External built residential environment characteristics were investigated for 544 residents living in different residential areas that were categorized by their socioeconomic status. Medically validated interview schedules were used to determine mental health of residents in the respective neighborhoods. The relationship between characteristics of the external built residential environment and mental health of residents was determined by multivariable logistic regression analyses and chi-square tests. The results show that walling materials used on buildings, density of dwelling units, state of street lighting, types of doors, states of roofs, and states of windows are some built external residential environment characteristics that affect mental health of adult males and females. Urban residential areas that are characterized by poor quality external built environment substantially expose the population to daily stressors and inconveniences that increase the likelihood of developing mental health disorders.

Fiber Optic Control System Integration program: for optical flight control system development

NASA Astrophysics Data System (ADS)

Weaver, Thomas L.; Seal, Daniel W.

1994-10-01

Hardware and software were developed for optical feedback links in the flight control system of an F/A-18 aircraft. Developments included passive optical sensors and optoelectronics to operate the sensors. Sensors with different methods of operation were obtained from different manufacturers and integrated with common optoelectronics. The sensors were the following: Air Data Temperature; Air Data Pressure; and Leading Edge Flap, Nose Wheel Steering, Trailing Edge Flap, Pitch Stick, Rudder, Rudder Pedal, Stabilator, and Engine Power Lever Control Position. The sensors were built for a variety of aircraft locations and harsh environments. The sensors and optoelectronics were as similar as practical to a production system. The integrated system was installed by NASA for flight testing. Wavelength Division Multiplexing proved successful as a system design philosophy. Some sensors appeared to be better choices for aircraft applications than others, with digital sensors generally being better than analog sensors, and rotary sensors generally being better than linear sensors. The most successful sensor approaches were selected for use in a follow-on program in which the sensors will not just be flown on the aircraft and their performance recorded; but, the optical sensors will be used in closing flight control loops.

Migration of the digital interactive breast-imaging teaching file

NASA Astrophysics Data System (ADS)

Cao, Fei; Sickles, Edward A.; Huang, H. K.; Zhou, Xiaoqiang

1998-06-01

The digital breast imaging teaching file developed during the last two years in our laboratory has been used successfully at UCSF (University of California, San Francisco) as a routine teaching tool for training radiology residents and fellows in mammography. Building on this success, we have ported the teaching file from an old Pixar imaging/Sun SPARC 470 display system to our newly designed telemammography display workstation (Ultra SPARC 2 platform with two DOME Md5/SBX display boards). The old Pixar/Sun 470 system, although adequate for fast and high-resolution image display, is 4- year-old technology, expensive to maintain and difficult to upgrade. The new display workstation is more cost-effective and is also compatible with the digital image format from a full-field direct digital mammography system. The digital teaching file is built on a sophisticated computer-aided instruction (CAI) model, which simulates the management sequences used in imaging interpretation and work-up. Each user can be prompted to respond by making his/her own observations, assessments, and work-up decisions as well as the marking of image abnormalities. This effectively replaces the traditional 'show-and-tell' teaching file experience with an interactive, response-driven type of instruction.

49 CFR 229.209 - Alternative locomotive crashworthiness designs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... locomotive crashworthiness design, in detail; (3) The intended type of service for locomotives built under the proposed design; and (4) Appropriate data and analysis showing how the design either satisfies the requirements of § 229.205 for the type of locomotive or provides at least an equivalent level of safety. Types...

24 CFR 3282.361 - Design Approval Primary Inspection Agency (DAPIA).

Code of Federal Regulations, 2010 CFR

2010-04-01

... manufactured home designs submitted to it by the manufacturer and for assuring that they conform to the....362 who deal with the design, quality assurance manual, or manufactured homes built to them, and by... submit floor plans and specific information for each manufactured home design or variation which the...

An Integrated Strategy for an Apparel Design Curriculum

ERIC Educational Resources Information Center

Bye, Elizabeth; Labat, Karen L.

2005-01-01

The core of apparel design education is the studio experience. This article discusses an Integrated Apparel Design Curriculum model built on a foundation of creative and technical experimentation and learning which contributes to developing abstract thinking skills. Various learning styles are supported as students work through the design process…

Helping Education Students Understand Learning through Designing

ERIC Educational Resources Information Center

Ronen-Fuhrmann, Tamar; Kali, Yael; Hoadley, Christopher

2008-01-01

This article describes a course in which graduate students in education learn practical and theoretical aspects of educational design by creating technologies for learning. The course was built around three themes: "Analyzing technologies," in which students study state-of- the-art technologies and interview their designers; "design studio," in…

Friction Stir Additive Manufacturing: Route to High Structural Performance

NASA Astrophysics Data System (ADS)

Palanivel, S.; Sidhar, H.; Mishra, R. S.

2015-03-01

Aerospace and automotive industries provide the next big opportunities for additive manufacturing. Currently, the additive industry is confronted with four major challenges that have been identified in this article. These challenges need to be addressed for the additive technologies to march into new frontiers and create additional markets. Specific potential success in the transportation sectors is dependent on the ability to manufacture complicated structures with high performance. Most of the techniques used for metal-based additive manufacturing are fusion based because of their ability to fulfill the computer-aided design to component vision. Although these techniques aid in fabrication of complex shapes, achieving high structural performance is a key problem due to the liquid-solid phase transformation. In this article, friction stir additive manufacturing (FSAM) is shown as a potential solid-state process for attaining high-performance lightweight alloys for simpler geometrical applications. To illustrate FSAM as a high-performance route, manufactured builds of Mg-4Y-3Nd and AA5083 are shown as examples. In the Mg-based alloy, an average hardness of 120 HV was achieved in the built structure and was significantly higher than that of the base material (97 HV). Similarly for the Al-based alloy, compared with the base hardness of 88 HV, the average built hardness was 104 HV. A potential application of FSAM is illustrated by taking an example of a simple stiffener assembly.

Proton conduction in metal-organic frameworks and related modularly built porous solids.

PubMed

Yoon, Minyoung; Suh, Kyungwon; Natarajan, Srinivasan; Kim, Kimoon

2013-03-04

Proton-conducting materials are an important component of fuel cells. Development of new types of proton-conducting materials is one of the most important issues in fuel-cell technology. Herein, we present newly developed proton-conducting materials, modularly built porous solids, including coordination polymers (CPs) or metal-organic frameworks (MOFs). The designable and tunable nature of the porous materials allows for fast development in this research field. Design and synthesis of the new types of proton-conducting materials and their unique proton-conduction properties are discussed. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of green infrastructure designs using the Automated Geospatial Watershed Assessment Tool

USDA-ARS?s Scientific Manuscript database

In arid and semi-arid regions, green infrastructure (GI) designs can address several issues facing urban environments, including augmenting water supply, mitigating flooding, decreasing pollutant loads, and promoting greenness in the built environment. An optimum design captures stormwater, addressi...