Laser-assisted electrochemical micromachining of mould cavity on the stainless steel surface

NASA Astrophysics Data System (ADS)

Li, Xiaohai; Wang, Shuming; Wang, Dong; Tong, Han

2018-02-01

In order to fabricate the micro mould cavities with complex structures on 304 stainless steel, laser-assisted electrochemical micromachining (EMM) based on surface modification by fiber laser masking was studied,and a new device of laser-assisted EMM was developed. Laser marking on the surface of 304 stainless steel can first be realized by fiber laser heating scanning. Through analysis of X ray diffraction analysis (XRD), metal oxide layer with predefined pattern can be formed by laser marking, and phase transformation can also occur on the 304 stainless steel surface, which produce the laser masking layer with corrosion resistance. The stainless steel surface with laser masking layer is subsequently etched by EMM, the laser masking layer severs as the temporary protective layer without relying on lithography mask, the fabrication of formed electrodes is also avoided, so micro pattern cavities can fast be fabricated. The impacts on machining accuracy during EMM with laser masking were discussed to optimize machining parameters, such as machining voltage, electrolyte concentration, duty cycle of pulse power supply and electrode gap size, the typical mould cavities 23μm deep were fabricated under the optimized parameters.

Impact of cloud timing on surface temperature and related hydroclimatic dynamics

NASA Astrophysics Data System (ADS)

Porporato, A. M.; Yin, J.

2015-12-01

Cloud feedbacks have long been identified as one of the largest source of uncertainty in climate change predictions. Differences in the spatial distribution of clouds and the related impact on surface temperature and climate dynamics have been recently emphasized in quasi-equilibrium General Circulation Models (GCM). However, much less attention has been paid to the temporal variation of cloud presence and thickness. Clouds in fact shade the solar radiation during the daytime, but also acts as greenhouse gas to reduce the emission of longwave radiation to the outer space anytime of the day. Thus it is logical to expect that even small differences in timing and thickness of clouds could result in very different predictions in GCMs. In this study, these two effects of cloud dynamics are analyzed by tracking the cloud impacts on longwave and shortwave radiation in a minimalist transient thermal balance model of the land surface. The marked changes in surface temperature due to alterations in the timing of onset of clouds demonstrate that capturing temporal variation of cloud at sub-daily scale should be a priority in cloud parameterization schemes in GCMs.

SPH for impact force and ricochet behavior of water-entry bodies

NASA Astrophysics Data System (ADS)

Omidvar, Pourya; Farghadani, Omid; Nikeghbali, Pooyan

The numerical modeling of fluid interaction with a bouncing body has many applications in scientific and engineering application. In this paper, the problem of water impact of a body on free-surface is investigated, where the fixed ghost boundary condition is added to the open source code SPHysics2D1 to rectify the oscillations in pressure distributions with the repulsive boundary condition. First, after introducing the methodology of SPH and the option of boundary conditions, the still water problem is simulated using two types of boundary conditions. It is shown that the fixed ghost boundary condition gives a better result for a hydrostatics pressure. Then, the dam-break problem, which is a bench mark test case in SPH, is simulated and compared with available data. In order to show the behavior of the hydrostatics forces on bodies, a fix/floating cylinder is placed on free surface looking carefully at the force and heaving profile. Finally, the impact of a body on free-surface is successfully simulated for different impact angles and velocities.

Cut marks on bone surfaces: influences on variation in the form of traces of ancient behaviour

PubMed Central

Braun, David R.; Pante, Michael; Archer, William

2016-01-01

Although we know that our lineage has been producing sharp-edged tools for over 2.6 Myr, our knowledge of what they were doing with these tools is far less complete. Studies of these sharp-edged stone tools show that they were most probably used as cutting implements. However, the only substantial evidence of this is the presence of cut marks on the bones of animals found in association with stone tools in ancient deposits. Numerous studies have aimed to quantify the frequency and placement of these marks. At present there is little consensus on the meaning of these marks and how the frequency relates to specific behaviours in the past. Here we investigate the possibility that mechanical properties associated with edges of stone tools as well as the properties of bones themselves may contribute to the overall morphology of these marks and ultimately their placement in the archaeological record. Standardized tests of rock mechanics (Young's modulus and Vickers hardness) indicate that the hardness of tool edges significantly affects cut-mark morphology. In addition, we show that indentation hardness of bones also impacts the overall morphology of cut marks. Our results show that rock type and bone portions influence the shape and prevalence of cut marks on animal bones. PMID:27274806

Muzzle imprint mark: a patterned injury which may be constituted of intradermal blood extravasations.

PubMed

Pircher, R; Bielefeld, L; Geisenberger, D; Große Perdekamp, M; Pollak, S; Thierauf-Emberger, A

2014-11-01

The muzzle imprint mark in contact shots is usually regarded as a patterned pressure abrasion depicting the barrel end as well as adjacent constructional components of the weapon. Due to parching after exposure to air, the affected skin assumes a brown color, especially along the contours of the impacting structures. Apart from this well-known type of epidermal damage, the imprint mark may also be formed by intradermal hemorrhages. In some cases, these intracutaneous bleedings manifest themselves as circular, curved or straight reddish lines mirroring the surface relief of the weapon's muzzle end. To estimate the frequency of skin hematomas in muzzle imprints, 35 consecutive contact shots to the head (temple, forehead, submental and occipital region) were evaluated. In 3 cases, the muzzle imprint mark exclusively consisted of intracutaneous bruises surrounding the bullet entrance hole. In 14 cases, the muzzle imprint was composed of both excoriations and intradermal hematomas. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Observations of Lunar Swirls by the Diviner Lunar Radiometer Experiment

NASA Technical Reports Server (NTRS)

Glotch, T. D.; Greenhagen, B. T.; Lucey, P. G.; Bandfield, J. L.; Hayne, Paul O.; Allen, Carlton C.; Elphic, Richard C.; Paige, D. A.

2012-01-01

The presence of anomalous, high albedo markings on the lunar surface has been known since the Apollo era. These features, collectively known as lunar swirls, occur on both the mare and highlands. Some swirls are associated with the antipodes of major impact basins, while all are associated with magnetic field anomalies of varying strength. Three mechanisms have been proposed for the formation of the swirls: (1) solar wind standoff due to the presence of magnetic fields, (2) micrometeoroid or comet swarms impacting and disturbing the lunar surface, revealing unweathered regolith, and (3) transport and deposition of fine-grained feldspathic material. Diviner s unique capabilities to determine silicate composition and degree of space weathering of the lunar surface, in addition to its capabilities to determine thermophysical properties from night-time temperature measurements, make it an ideal instrument to examine the swirls and help differentiate among the three proposed formation mechanisms.

Scanning-electron-microscope study of normal-impingement erosion of ductile metals

NASA Technical Reports Server (NTRS)

Brainard, W. A.; Salik, J.

1980-01-01

Scanning electron microscopy was used to characterize the erosion of annealed copper and aluminum surfaces produced by both single- and multiple-particle impacts. Macroscopic 3.2 mm diameter steel balls and microscopic, brittle erodant particles were projected by a gas gun system so as to impact at normal incidence at speeds up to 140 m/sec. During the impacts by the brittle erodant particles, at lower speeds the erosion behavior was similar to that observed for the larger steel balls. At higher velocities, particle fragmentation and the subsequent cutting by the radial wash of debris created a marked change in the erosion mechanism.

Impact of Urban Growth on Surface Climate: A Case Study in Oran, Algeria

NASA Technical Reports Server (NTRS)

Bounoua, Lahouari; Safia, Abdelmounaine; Masek, Jeffrey; Peters-Lidars, Christaq; Imhoff, Marc L.

2008-01-01

We develop a land use map discriminating urban surfaces from other cover types over a semiarid region in North Africa and use it in a land surface model to assess the impact of urbanized land on surface energy, water and carbon balances. Unlike in temperate climates where urbanization creates a marked heat island effect, this effect is not strongly marked in semiarid regions. During summer, the urban class results in an additional warming of 1.45 C during daytime and 0.81 C at night compared to that simulated for needleleaf trees under similar climate conditions. Seasonal temperatures show urban areas warmer than their surrounding during summer and slightly cooler in winter. The hydrological cycle is practically "shut down" during summer and characterized by relatively large amount of runoff in winter. We estimate the annual amount of carbon uptake to 1.94 million metric tons with only 11.9% assimilated during the rainy season. However, if urbanization expands to reach 50% of the total area excluding forests, the annual total carbon uptake will decline by 35% and the July mean temperature would increase only 0.10 C, compared to current situation. In contrast, if urbanization expands to 50% of the total land excluding forests and croplands but all short vegetation is replaced by native broadleaf deciduous trees, the annual carbon uptake would increase 39% and the July mean temperature would decrease by 0.9 C, compared to current configuration. These results provide guidelines for urban planners and land use managers and indicate possibilities for mitigating the urban heat.

Water-Surface Elevations, Discharge, and Water-Quality Data for Selected Sites in the Warm Springs Area near Moapa, Nevada

USGS Publications Warehouse

Beck, David A.; Ryan, Roslyn; Veley, Ronald J.; Harper, Donald P.; Tanko, Daron J.

2006-01-01

The U.S. Geological Survey, in cooperation with Southern Nevada Water Authority and the Nevada Division of Water Resources, operates and maintains a surface-water monitoring network of 6 continuous-record stream-flow gaging stations and 11 partial-record stations in the Warm Springs area near Moapa, Nevada. Permanent land-surface bench marks were installed within the Warm Springs area by the Las Vegas Valley Water District, the Southern Nevada Water Authority, and the U.S. Geological Survey to determine water-surface elevations at all network monitoring sites. Vertical datum elevation and horizontal coordinates were established for all bench marks through a series of Differential Global Positioning System surveys. Optical theodolite surveys were made to transfer Differential Global Positioning System vertical datums to reference marks installed at each monitoring site. The surveys were completed in June 2004 and water-surface elevations were measured on August 17, 2004. Water-surface elevations ranged from 1,810.33 feet above North American Vertical Datum of 1988 at a stream-gaging station in the Pederson Springs area to 1,706.31 feet at a station on the Muddy River near Moapa. Discharge and water-quality data were compiled for the Warm Springs area and include data provided by the U.S. Geological Survey, Nevada Division of Water Resources, U.S. Fish and Wildlife Service, Moapa Valley Water District, Desert Research Institute, and Converse Consultants. Historical and current hydrologic data-collection networks primarily are related to changes in land- and water-use activities in the Warm Springs area. These changes include declines in ranching and agricultural use, the exportation of water to other areas of Moapa Valley, and the creation of a national wildlife refuge. Water-surface elevations, discharge, and water-quality data compiled for the Warm Springs area will help identify (1) effects of changing vegetation within the former agricultural lands, (2) effects of restoration activities in the wildlife refuge, and (3) potential impacts of ground-water withdrawals.

Impact wear behavior of human tooth enamel under simulated chewing conditions.

PubMed

Zheng, Jing; Zeng, Yangyang; Wen, Jian; Zheng, Liang; Zhou, Zhongrong

2016-09-01

Previous studies mostly focused on the sliding wear behavior of human teeth, and little effort has been made so far to study the impact wear of human teeth. The objective of this study was to investigate the impact wear process and mechanism of human tooth enamel and the influence of water content within enamel. In this paper, the impact wear behaviors of fresh and dried human tooth enamel against SiC ceramic have been investigated using a specially designed impact test machine. Tests lasting up to 5×10(3), 5×10(4), 2.5×10(5), 5.5×10(5), 8×10(5) and 1×10(6) cycles were conducted, respectively. Results showed that for the fresh enamel, the surface damage was dominated by plastic deformation at the early stage of impact wear. Iridescent rings appeared around the impact mark as a result of the accumulation and spread of plastic deformation. As the impact wear progressed, delamination occurred on the surface of enamel, and thus the iridescent rings gradually disappeared. Wear loss increased rapidly with the increase of impact cycles. When a wear particle layer was formed on the enamel surface, the wear rate decreased. It was found that the surface hardness of enamel increased with the impact cycles, and no cracks appeared on the cross section of wear scar. Compared with the fresh enamel, the fracture toughness of dried enamel decreased, and thus there were microcracks appearing on the cross section of wear scar. More obvious delamination occurred on the worn surface of dried enamel, and no iridescent rings were observed. The wear loss of dried enamel was higher than that of fresh enamel. In summary, the impact wear behavior of sound human tooth enamel was metal-like to some degree, and no subsurface cracking occurred. The water content within enamel could increase its fracture toughness and protect the surface from impact wear. The wear mechanism of human tooth enamel is determined by its microstructure. Copyright © 2016 Elsevier Ltd. All rights reserved.

Recovering obliterated engraved marks on aluminium surfaces by etching technique.

PubMed

Baharum, Mohd Izhar Mohd; Kuppuswamy, R; Rahman, Azari Abd

2008-05-20

A study has been made of the characteristics of restoration of obliterated engraved marks on aluminium surfaces by etching technique. By etching different reagents on 0.61mm thick sheets of aluminium (99wt%) on which some engraved marks had been erased to different depths it was found that the reagent 60% hydrochloric acid and 40% sodium hydroxide on alternate swabbing on the surfaces was found to be the most sensitive one for these metal surfaces. This reagent was able to restore marks in the above plates erased down to 0.04mm below the bottom of the engraving. The marks also presented excellent contrast with the background. This reagent was further experimented with similar aluminium surfaces, but of relatively greater thickness of 1.5mm. It was noticed that the recovery depth increased slightly to 0.06mm; this suggested the dependence of recovery depth on the thickness of the sheet metal. Further, the depth of restoration decreased in cases where the original number was erased and over which a new number was engraved; the latter results are similar to those of steel surfaces reported earlier [M.A.M. Zaili, R. Kuppuswamy, H. Harun, Restoration of engraved marks on steel surfaces by etching technique, Forensic Sci. Int. 171 (2007) 27-32].

Stand, species, and individual traits impact transpiration in historically disturbed forests.

NASA Astrophysics Data System (ADS)

Blakely, B.; Rocha, A. V.; McLachlan, J. S.

2017-12-01

Historic logging disturbances have changed the structure and species composition of most Northern temperate forests. These changes impact the process of transpiration - which in turn impacts canopy surface temperature - but the links among structure, composition, and transpiration remain unclear. For this reason, ecosystem models typically use simplified structure and composition to simulate the impact of disturbances on forest transpiration. However, such simplifications ignore real variability among stands, species, and individual trees that may strongly influence transpiration across spatial and temporal scales. To capture this variability, we monitored transpiration in 48 individual trees of multiple species in both undisturbed (400+ yr) and historically logged (80 - 120 yr) forests. Using modern and historic forest surveys, we upscaled our observations to stand and regional scales to identify the key changes impacting transpiration. We extended these inferences by establishing a relationship between transpiration and measured surface temperature, linking disturbance-induced changes in structure and composition to local and regional climate. Despite greater potential evapotranspiration and basal area, undisturbed forest transpired less than disturbed (logged) forest. Transpiration was a strong predictor of surface temperature, and the canopy surface was warmer in undisturbed forest. Transpiration differences among disturbed and undisturbed forests resulted from (1) lesser transpiration and dampened seasonality in evergreen species (2) greater transpiration in younger individuals within a species, and (3) strong transpiration by large individuals. When transpiration was scaled to the stand or regional level in a simplified manner (e.g. a single transpiration rate for all deciduous individuals), the resulting estimates differed markedly from the original. Stand- species- and individual-level traits are therefore essential for understanding how transpiration and surface temperature respond to disturbance. Without consideration of such traits, current ecosystem models may struggle to capture the true impact of logging disturbances on forest transpiration.

The use of dental putty in the assessment of hard surfaces within paved urban areas that may leave defined or patterned marks on bodies.

PubMed

Johnson, Oliver Ross; Lyall, Matt; Johnson, Christopher Paul

2015-04-01

The identification of a patterned skin or scalp mark at autopsy can provide key forensic evidence in identifying an injury that may have been left by an assailant's footwear. It is also important to consider whether such a mark could alternatively have been left by the deceased coming into forceful contact with a hard surface at the scene of an incident, for example by falling. This study was designed to demonstrate how variable surfaces are within paved urban areas, including those which might leave marks resembling footwear patterns, and to evaluate whether dental putty impression lifting is a practical and effective adjunct to photography in assessing patterned surfaces. Eighteen 'scenes' of approximately 50 m² were assessed for different hard surfaces by photography and by the production of dental putty impression lifts. The number of hard surfaces varied between 4 and 12 per scene, with 90% (122/135) of all hard surfaces deemed likely to leave distinct marking on skin with forceful contact and 46% (62/135) a defined/regular mark potentially similar to a footwear injury (mean = 3.4 per scene). Dental putty proved to be an excellent tool in characterising hard surfaces, producing firm but slightly flexible lifts that can be used in combination with a commercially available inkless footwear impression kit to generate transparencies that help facilitate detailed comparison work. Whenever a potential footwear mark is identified at autopsy, a systematic examination of all hard surfaces at the scene is mandatory, and this process will be significantly strengthened by the use of dental putty. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Forensic firearm identification of semiautomatic handguns using laser formed microstamping elements

NASA Astrophysics Data System (ADS)

Lizotte, Todd E.; Ohar, Orest

2008-08-01

For well over one hundred years the science of Firearm and Tool Mark Identification has relied on the theory that unintentional random tooling marks generated during the manufacture of a firearm onto its interior surfaces are unique to each individual firearm.[1][2] Forensic Firearm and Tool Mark Examiners have had to rely on the analysis of these randomly formed unintentional striations, or scratches and dings, transferred onto ammunition components from firearms used to commit crimes, as a way of developing clues and evidence. Such transfers take place during the cycle of fire and ejection of the cartridge from the firearm during the commission of a crime. The typical striations on the cartridge casings are caused by tooling marks that are randomly formed during the machining of interior surfaces of the manufactured firearm and by other firearm components that come in contact with the cycling ammunition. Components like the firing pin, extractor and ejector, impact the surfaces of the cartridges as they are fed, fired and ejected from the firearm. When found at a crime scene, these striae constitute ballistic evidence when effectively analyzed by a Forensic Firearm and Tool Mark Examiner. Examiners categorize these striations looking for matches to be made between the components that created the marks and the recovered firearm. Reality is that nearly 50% of firearms used in violent crimes are not recovered at a crime scene, requiring the analysis to be processed and logged into evidence files or imaged into reference image databases for future comparison whenever a firearm might be recovered. This paper will present a unique law enforcement technology, embedded into firearms for tracking the sources of illegally trafficked firearms, called Microstamping. Microstamping is a laser based micromachining process that forms microscopic "intentional structures and marks" on components within a firearm. Thus when the firearm is fired, these microstamp structures transfer an identifying tracking code onto the expended cartridge ejected from the firearm. Microstamped structures are laser micromachined alpha numeric and encoded geometric tracking numbers, linked to the serial number of the firearm. Ballistic testing data will be presented covering microstamp transfer quality, transfer rates and survivability/durability. Further information will provide an overview on how microstamping information can be utilized by law enforcement to combat illegal firearm trafficking.

ARC-1979-A79-7093

NASA Image and Video Library

1979-07-09

Range : 225,000 kilometers (140,625 miles) This image of the Jovian moon Europa was taken by Voyager 2 along the evening terminator, which best shows the surface topography of complex narrow ridges, seen as curved bright streaks, 5 to 10 kilometers wide, and typically 100 kilometers in length. The area shown is about 600 by 800 kilometers, and the smallest features visible are about 4 kilometers in size. Also visable are dark bands, more diffused in character, 20 to 40 kilometers wide and hundreds to thousands of kilometers in length. A few features are suggestive of impact craters but are rare, indication that the surface thought to be dominantly ice is still active, perhaps warmed by tidal heating like Io. The larger icy satellites, Callisto and Ganymede, are evidently colder with much more rigid crusts and ancient impact craters. The complex intersection of dark markings and bright ridges suggest that the surface has been fractured and material from beneath has welled up to fill the cracks.

Oxygen Plasma Modification of Poss-Coated Kapton(Registered TradeMark) HN Films

NASA Technical Reports Server (NTRS)

Wohl, C. J.; Belcher, M. A.; Ghose, S.; Connell, J. W.

2008-01-01

The surface energy of a material depends on both surface composition and topographic features. In an effort to modify the surface topography of Kapton(Registered TradeMark) HN film, organic solutions of a polyhedral oligomeric silsesquioxane, octakis(dimethylsilyloxy)silsesquioxane (POSS), were spray-coated onto the Kapton(Registered TradeMark) HN surface. Prior to POSS application, the Kapton(Registered TradeMark) HN film was activated by exposure to radio frequency (RF)-generated oxygen plasma. After POSS deposition and solvent evaporation, the films were exposed to various durations of RF-generated oxygen plasma to create a topographically rich surface. The modified films were characterized using optical microscopy, attenuated total reflection infrared (ATR-IR) spectroscopy, and high-resolution scanning electron microscopy (HRSEM). The physical properties of the modified films will be presented.

Pavement marking demonstration projects : state of Alaska and state of Tennessee.

DOT National Transportation Integrated Search

2013-11-01

This project evaluates the safety impacts, environmental impacts, and cost effectiveness of different pavement marking : systems as well as the effect of State bidding and procurement processes on the quality of pavement marking material : employed i...

Impact Crater in Coastal Patagonia

NASA Technical Reports Server (NTRS)

D'Antoni, Hector L; Lasta, Carlos A.; Condon, Estelle (Technical Monitor)

2000-01-01

Impact craters are geological structures attributed to the impact of a meteoroid on the Earth's (or other planet's) surface (Koeberl and Sharpton. 1999). The inner planets of the solar system as well as other bodies such as our moon show extensive meteoroid impacts (Gallant 1964, French 1998). Because of its size and gravity, we may assume that the Earth has been heavily bombarded but weathering and erosion have erased or masked most of these features. In the 1920's, a meteor crater (Mark 1987) was identified in Arizona and to this first finding the identification of a large number of impact structures on Earth followed (Hodge 1994). Shock metamorphic effects are associated with meteorite impact craters. Due to extremely high pressures, shatter cones are produced as well as planar features in quartz and feldspar grains, diaplectic glass and high-pressure mineral phases such as stishovite (French 1998).

Surface Textural Analysis of Quartz Grains from Modern Point Bar Deposits in Lower Reaches of the Yellow River

NASA Astrophysics Data System (ADS)

Cheng, Yong; Liu, Cong; Lu, Ping; Zhang, Yu; Nie, Qi; Wen, Yiming

2018-01-01

The surfaces of quartz grains contain characteristic textures formed during the process of transport, due to their stable physical and chemical properties. The surface textures include the information about source area, transporting force, sedimentary environment and evolution history of sediment. Surface textures of quartz grains from modern point bar deposits in the lower reaches of the Yellow River are observed and studied by scanning electron microscopy (SEM). Results indicate that there are 22 kinds of surface textures. The overall surface morphology of quartz grains shows short transporting time and distance and weak abrasive action of the river water. The combined surface textures caused by mechanical action indicate that quartz grains are transporting in a high-energy hydrodynamic condition and suffer a strong mechanical impact and abrasion. The common solution pits prove that the chemical property of transportation medium is very active and quartz grains receive an obvious chemical action. The combination of these surface textures can be an identification mark of fluvial environment, and that is: quartz grains are main subangular outline, whose roundness is higher with the farther motion distance; Surface fluctuation degree of quartz grains is relatively high, and gives priority to high and medium relief; V-shaped percussion marks are very abundant caused by mechanical action; The conchoidal of different sizes and steps are common-developed with paragenesis relationship; Solution pits are common-developed as well. The study makes up for the blank of surface textures analysis of quartz grains from modern fluvial deposits in China. It provides new ideas and evidence for studies of the sedimentary process and environmental significance, although the deep meanings of these micro textures remain to be further researched.

Characterization of Titanium Oxide Layers Formation Produced by Nanosecond Laser Coloration

NASA Astrophysics Data System (ADS)

Brihmat-Hamadi, F.; Amara, E. H.; Kellou, H.

2017-06-01

Laser marking technique is used to produce colors on titanium while scanning a metallic sample under normal atmospheric conditions. To proceed with different operating conditions related to the laser beam, the parameters of a Q-switched diode-pumped Nd:YAG ( λ = 532 nm) laser, with a pulse duration of τ = 5 ns, are varied. The effect on the resulting mark quality is the aim of the present study which is developed to determine the influence of the operating parameters ( i.e., pulse frequency, beam scanning speed, and pumping intensity) and furthermore their combination, such as the accumulated fluences and the overlapping rate of laser impacts. From the obtained experimental results, it is noted that the accumulated fluences and the scanning speed are the most influential operating parameters during laser marking, since they have a strong effect on the surface roughness and reflectance, and the occurrence of many oxide phases such as TiO, Ti2O3, TiO2 ( γ- phase, anatase, and rutile).

The air bubble entrapped under a drop impacting on a solid surface

NASA Astrophysics Data System (ADS)

Thoroddsen, S. T.; Etoh, T. G.; Takehara, K.; Ootsuka, N.; Hatsuki, Y.

2005-12-01

We present experimental observations of the disk of air caught under a drop impacting onto a solid surface. By imaging the impact through an acrylic plate with an ultra-high-speed video camera, we can follow the evolution of the air disk as it contracts into a bubble under the centre of the drop. The initial size and contraction speed of the disk were measured for a range of impact Weber and Reynolds numbers. The size of the initial disk is related to the bottom curvature of the drop at the initial contact, as measured in free-fall. The initial contact often leaves behind a ring of micro-bubbles, marking its location. The air disk contracts at a speed comparable to the corresponding air disks caught under a drop impacting onto a liquid surface. This speed also seems independent of the wettability of the liquid, which only affects the azimuthal shape of the contact line. For some impact conditions, the dynamics of the contraction leaves a small droplet at the centre of the bubble. This arises from a capillary wave propagating from the edges of the contracting disk towards the centre. As the wave converges its amplitude grows until it touches the solid substrate, thereby pinching off the micro-droplet at the plate, in the centre of the bubble. The effect of increasing liquid viscosity is to slow down the contraction speed and to produce a more irregular contact line leaving more micro-bubbles along the initial ring.

Basic Research of Intrinsic Tamper Indication Markings Defined by Pulsed Laser Irradiation (Quad Chart).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moody, Neville R.

Objective: We will research how short (ns) and ultrashort (fs) laser pulses interact with the surfaces of various materials to create complex color layers and morphological patterns. Method: We are investigating the site-specific, formation of microcolor features. Also, research includes a fundamental study of the physics underlying periodic ripple formation during femtosecond laser irradiation. Status of effort: Laser induced color markings were demonstrated on an increased number of materials (including metal thin films) and investigated for optical properties and microstructure. Technology that allows for marking curved surfaces (and large areas) has been implemented. We have used electro-magnetic solvers to modelmore » light-solid interactions leading to periodic surface ripple patterns. This includes identifying the roles of surface plasmon polaritons. Goals/Milestones: Research corrosion resistance of oxide color markings (salt spray, fog, polarization tests); Through modeling, investigate effects of multi-source scattering and interference on ripple patterns; Investigate microspectrophotometry for mapping color; and Investigate new methods for laser color marking curved surfaces and large areas.« less

46 CFR 108.661 - Unit markings: Draft marks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Unit markings: Draft marks. 108.661 Section 108.661... AND EQUIPMENT Equipment Markings and Instructions § 108.661 Unit markings: Draft marks. (a) Each unit must have draft marks for each foot of immersion— (1) If the unit is a surface unit, on both the port...

46 CFR 108.661 - Unit markings: Draft marks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Unit markings: Draft marks. 108.661 Section 108.661... AND EQUIPMENT Equipment Markings and Instructions § 108.661 Unit markings: Draft marks. (a) Each unit must have draft marks for each foot of immersion— (1) If the unit is a surface unit, on both the port...

46 CFR 108.661 - Unit markings: Draft marks.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Unit markings: Draft marks. 108.661 Section 108.661... AND EQUIPMENT Equipment Markings and Instructions § 108.661 Unit markings: Draft marks. (a) Each unit must have draft marks for each foot of immersion— (1) If the unit is a surface unit, on both the port...

46 CFR 108.661 - Unit markings: Draft marks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Unit markings: Draft marks. 108.661 Section 108.661... AND EQUIPMENT Equipment Markings and Instructions § 108.661 Unit markings: Draft marks. (a) Each unit must have draft marks for each foot of immersion— (1) If the unit is a surface unit, on both the port...

46 CFR 108.661 - Unit markings: Draft marks.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Unit markings: Draft marks. 108.661 Section 108.661... AND EQUIPMENT Equipment Markings and Instructions § 108.661 Unit markings: Draft marks. (a) Each unit must have draft marks for each foot of immersion— (1) If the unit is a surface unit, on both the port...

Marked surface inversions and wind shear: A safety risk for departing aircraft

NASA Technical Reports Server (NTRS)

Korhonen, O.

1983-01-01

Marked surface inversions occur most frequently in dry continental climates, where low atmospheric humidity allows heat transfer by long wave thermal radiation. In the northern latitudes, surface inversions reach their maximum intensity during the winter, when the incoming Sun's radiation is negligible and radiative cooling is dominant during the long nights. During winter, air mass boundaries are sharp, which causes formation of marked surface inversions. The existence of these inversions and sharp boundaries increase the risk of wind shear. The information should refer to marked inversions exceeding a temperature difference of 10 deg C up to 1000 feet. The need to determine the temperature range over which he information is operationally needed and the magnitude of the inversion required before a notification to pilots prior to departure is warranted are outlined.

Surface laser marking optimization using an experimental design approach

NASA Astrophysics Data System (ADS)

Brihmat-Hamadi, F.; Amara, E. H.; Lavisse, L.; Jouvard, J. M.; Cicala, E.; Kellou, H.

2017-04-01

Laser surface marking is performed on a titanium substrate using a pulsed frequency doubled Nd:YAG laser ( λ= 532 nm, τ pulse=5 ns) to process the substrate surface under normal atmospheric conditions. The aim of the work is to investigate, following experimental and statistical approaches, the correlation between the process parameters and the response variables (output), using a Design of Experiment method (DOE): Taguchi methodology and a response surface methodology (RSM). A design is first created using MINTAB program, and then the laser marking process is performed according to the planned design. The response variables; surface roughness and surface reflectance were measured for each sample, and incorporated into the design matrix. The results are then analyzed and the RSM model is developed and verified for predicting the process output for the given set of process parameters values. The analysis shows that the laser beam scanning speed is the most influential operating factor followed by the laser pumping intensity during marking, while the other factors show complex influences on the objective functions.

Localization of burn mark under an abnormal topography on MOSFET chip surface using liquid crystal and emission microscopy tools.

PubMed

Lau, C K; Sim, K S; Tso, C P

2011-01-01

This article focuses on the localization of burn mark in MOSFET and the scanning electron microscope (SEM) inspection on the defect location. When a suspect abnormal topography is shown on the die surface, further methods to pin-point the defect location is necessary. Fault localization analysis becomes important because an abnormal spot on the chip surface may and may not have a defect underneath it. The chip surface topography can change due to the catastrophic damage occurred at layers under the chip surface, but it could also be due to inconsistency during metal deposition in the wafer fabrication process. Two localization techniques, liquid crystal thermography and emission microscopy, were performed to confirm that the abnormal topography spot is the actual defect location. The tiny burn mark was surfaced by performing a surface decoration at the defect location using hot hydrochloric acid. SEM imaging, which has the high magnification and three-dimensional capabilities, was used to capture the images of the burn mark. Copyright © 2011 Wiley Periodicals, Inc.

Venera 13 and venera 14: sedimentary rocks on venus?

PubMed

Florensky, C P; Basilevsky, A T; Kryuchkov, V P; Kusmin, R O; Nikolaeva, O V; Pronin, A A; Chernaya, I M; Tyuflin, Y S; Selivanov, A S; Naraeva, M K; Ronca, L B

1983-07-01

Venera 13 and Venera 14 transmitted almost complete panoramic views of their landing sites. Analyses of the photographs show the presence of rock formations undergoing geomorphic degradation. The formations display ripple marks, thin layering, differential erosion, and curvilinear fracturings. Some of them are interpreted as lithified clastic sediments. The lithification could have taken place at depth or at the surface, resulting in a type of duricrust. The origin of the sediments is unknown but could be aeolian, volcanic, or related to impacts or to turbidity currents.

Marking Extended Essays on Screen: Exploring the Link between Marking Processes and Comprehension

ERIC Educational Resources Information Center

Johnson, Martin; Hopkin, Rebecca; Shiell, Hannah

2012-01-01

Technological developments are impacting upon UK assessment practices in many ways. For qualification awarding bodies, a key example of such impact is the ongoing shift towards examiners marking digitally scanned copies of examination scripts on screen rather than the original paper documents. This digitisation process has obvious benefits,…

Investigation of Meniscus Region Behavior and Oscillation Mark Formation in Steel Continuous Casting Using a Transient Thermo-Fluid Model

NASA Astrophysics Data System (ADS)

Blaes, Carly

In the continuous casting of steel, many complex phenomena in the meniscus region of the mold are responsible for the formation of oscillation marks. Oscillation marks are depressions found around the perimeter of continuously cast steel slabs, which if too large can lead to cracking in steel slabs. Therefore, knowledge on how to minimize the size of oscillation marks is very valuable. A computational model was created of the meniscus region, which includes transient multiphase fluid flow of slag and steel, with low-Reynolds turbulence, heat transfer in the mold, slag, and steel, steel shell solidification, mold oscillation, and temperature-dependent properties. This model was first validated using previous experimental and plant data. The model was then used to study the impact of varying casting parameters, including oscillation frequency, stroke, modification ratio, casting speed, molten steel level fluctuations, and temperature-dependent slag properties and surface tension on the oscillation mark shape, and other aspects of thermal-flow behavior during each oscillation cycle, including heat flux profile, slag consumption and mold friction. The first half of oscillation marks were formed during negative strip time as the slag rim pushed molten steel away from the mold wall and that the second half of oscillation marks were formed during positive strip time as the molten steel is drawn near the mold wall due to the upstroke of the mold. Oscillation mark depth was found to decrease with increasing frequency, modification ratio, casting speed, and slag viscosity, while oscillation mark depth was found to increase with increasing stroke. Oscillation mark width was only found to increase due to increases in pitch, which can be contributed to decreasing frequency or increasing casting speed. While many observations were made in this study, in general, oscillation mark depth and total slag consumption increase with increasing negative strip time, while the average heat flux and average mold friction decrease with increasing negative strip time.

Front lighted optical tooling method and apparatus

DOEpatents

Stone, William J.

1985-06-18

An optical tooling method and apparatus uses a front lighted shadowgraphic technique to enhance visual contrast of reflected light. The apparatus includes an optical assembly including a fiducial mark, such as cross hairs, reflecting polarized light with a first polarization, a polarizing element backing the fiducial mark and a reflective surface backing the polarizing element for reflecting polarized light bypassing the fiducial mark and traveling through the polarizing element. The light reflected by the reflecting surface is directed through a second pass of the polarizing element toward the frontal direction with a polarization differing from the polarization of the light reflected by the fiducial mark. When used as a tooling target, the optical assembly may be mounted directly to a reference surface or may be secured in a mounting, such as a magnetic mounting. The optical assembly may also be mounted in a plane defining structure and used as a spherometer in conjunction with an optical depth measuring instrument. A method of measuring a radius of curvature of an unknown surface includes positioning the spherometer on a surface between the surface and a depth measuring optical instrument. As the spherometer is frontally illuminated, the distance from the depth measuring instrument to the fiducial mark and the underlying surface are alternately measured and the difference in these measurements is used as the sagittal height to calculate a radius of curvature.

Photographer : JPL Range : 225,000 kilometers (140,625 miles) This image of the Jovian moon Europa

NASA Technical Reports Server (NTRS)

1979-01-01

Photographer : JPL Range : 225,000 kilometers (140,625 miles) This image of the Jovian moon Europa was taken by Voyager 2 along the evening terminator, which best shows the surface topography of complex narrow ridges, seen as curved bright streaks, 5 to 10 kilometers wide, and typically 100 kilometers in length. The area shown is about 600 by 800 kilometers, and the smallest features visible are about 4 kilometers in size. Also visable are dark bands, more diffused in character, 20 to 40 kilometers wide and hundreds to thousands of kilometers in length. A few features are suggestive of impact craters but are rare, indication that the surface thought to be dominantly ice is still active, perhaps warmed by tidal heating like Io. The larger icy satellites, Callisto and Ganymede, are evidently colder with much more rigid crusts and ancient impact craters. The complex intersection of dark markings and bright ridges suggest that the surface has been fractured and material from beneath has welled up to fill the cracks.

ARC-1979-A79-7097

NASA Image and Video Library

1979-07-08

Range : 85,000 kilometers (53,000 miles) This photo of Jupiter's satellite Ganymede shows ancient cratered terrain. A variety of impact craters of different ages are shown. The brightest craters are the youngest. The ejecta blankets fade with age. The center shows a bright patch that represents the rebounding of the floor of the crater. The dirty ice has lost all topography except for faint circular patterns. Also shown are the 'Callisto type' curved troughs and ridges that mark an ancient enormous impact basin. The basin itself has been destroyed by later geologic processes. Only the ring features are preserved on the ancient surface. Near the bottom of the picture, these curved features are trumcated by the younger grooved terrain.

Evaluating pavement markings on portland cement concrete (PCC) and various asphalt surfaces : results of year 1 data collection.

DOT National Transportation Integrated Search

2013-12-01

The Illinois Department of Transportation (IDOT) uses a variety of different pavement marking : systems and has experienced a wide range of pavement marking performance. In an effort to : maximize marking performance and to optimize marking selection...

Enhanced magneto-optical imaging of internal stresses in the removed surface layer

NASA Astrophysics Data System (ADS)

Agalidi, Yuriy; Kozhukhar, Pavlo; Levyi, Sergii; Turbin, Dmitriy

2015-10-01

The paper describes a software method of reconstructing the state of the removed surface layer by visualising internal stresses in the underlying layers of the sample. Such a problem typically needs to be solved as part of forensic investigation that aims to reveal original marking of a sample with removed surface layer. For example, one may be interested in serial numbers of weapons or vehicles that had the surface layer of metal removed from the number plate. Experimental results of studying gradient internal stress fields in ferromagnetic sample using the NDI method of magneto-optical imaging (MOI) are presented. Numerical modelling results of internal stresses enclosed in the surface marking region are analysed and compared to the experimental results of magneto-optical imaging (MOI). MOI correction algorithm intended for reconstructing internal stress fields in the removed surface layer by extracting stresses retained by the underlying layers is described. Limiting ratios between parameters of a marking font are defined for the considered correction algorithm. Enhanced recognition properties for hidden stresses left by marking symbols are experimentally verified and confirmed.

Swift heavy ion irradiation of CaF2 - from grooves to hillocks in a single ion track

NASA Astrophysics Data System (ADS)

Gruber, Elisabeth; Salou, Pierre; Bergen, Lorenz; El Kharrazi, Mourad; Lattouf, Elie; Grygiel, Clara; Wang, Yuyu; Benyagoub, Abdenacer; Levavasseur, Delphine; Rangama, Jimmy; Lebius, Henning; Ban-d'Etat, Brigitte; Schleberger, Marika; Aumayr, Friedrich

2016-10-01

A novel form of ion-tracks, namely nanogrooves and hillocks, are observed on CaF2 after irradiation with xenon and lead ions of about 100 MeV kinetic energy. The irradiation is performed under grazing incidence (0.3°-3°) which forces the track to a region in close vicinity to the surface. Atomic force microscopy imaging of the impact sites with high spatial resolution reveals that the surface track consists in fact of three distinct parts: each swift heavy ion impacting on the CaF2 surface first opens a several 100 nm long groove bordered by a series of nanohillocks on both sides. The end of the groove is marked by a huge single hillock and the further penetration of the swift projectile into deeper layers of the target is accompanied by a single protrusion of several 100 nm in length slowly fading until the track vanishes. By comparing experimental data for various impact angles with results of a simulation, based on a three-dimensional version of the two-temperature-model (TTM), we are able to link the crater and hillock formation to sublimation and melting processes of CaF2 due to the local energy deposition by swift heavy ions.

Thermal effects of laser marking on microstructure and corrosion properties of stainless steel.

PubMed

Švantner, M; Kučera, M; Smazalová, E; Houdková, Š; Čerstvý, R

2016-12-01

Laser marking is an advanced technique used for modification of surface optical properties. This paper presents research on the influence of laser marking on the corrosion properties of stainless steel. Processes during the laser beam-surface interaction cause structure and color changes and can also be responsible for reduction of corrosion resistance of the surface. Corrosion tests, roughness, microscopic, energy dispersive x-ray, grazing incidence x-ray diffraction, and ferrite content analyses were carried out. It was found that increasing heat input is the most crucial parameter regarding the degradation of corrosion resistance of stainless steel. Other relevant parameters include the pulse length and pulse frequency. The authors found a correlation between laser processing parameters, grazing incidence x-ray measurement, ferrite content, and corrosion resistance of the affected surface. Possibilities and limitations of laser marking of stainless steel in the context of the reduction of its corrosion resistance are discussed.

Removal of single point diamond-turning marks by abrasive jet polishing.

PubMed

Li, Z Z; Wang, J M; Peng, X Q; Ho, L T; Yin, Z Q; Li, S Y; Cheung, C F

2011-06-01

Single point diamond turning (SPDT) is highly controllable and versatile in producing axially symmetric forms, non-axially-symmetric forms, microstructured surfaces, and free forms. However, the fine SPDT marks left in the surface limit its performance, and they are difficult to reduce or eliminate. It is unpractical for traditional methods to remove the fine marks without destroying their forms, especially for the aspheres and free forms. This paper introduces abrasive jet polishing (AJP) for the posttreatment of diamond-turned surfaces to remove the periodic microstructures. Samples of diamond-turned electroless nickel plated plano mirror were used in the experiments. One sample with an original surface roughness of more than 400 nm decreased to 4 nm after two iterations abrasive jet polishing; the surface roughness of another sample went from 3.7 nm to 1.4 nm after polishing. The periodic signatures on both of the samples were removed entirely after polishing. Contrastive experimental research was carried out on electroless nickel mirror with magnetorheological finishing, computer controlled optical surfacing, and AJP. The experimental results indicate that AJP is more appropriate in removing the periodic SPDT marks. Also, a figure maintaining experiment was carried out with the AJP process; the uniform polishing process shows that the AJP process can remove the periodic turning marks without destroying the original form.

The surface structure of silver-coated gold nanocrystals and its influence on shape control

DOE PAGES

Padmos, J. Daniel; Personick, Michelle L.; Tang, Qing; ...

2015-07-08

Understanding the surface structure of metal nanocrystals with specific facet indices is important due to its impact on controlling nanocrystal shape and functionality. However, this is particularly challenging for halide-adsorbed nanocrystals due to the difficulty in analysing interactions between metals and light halides (for example, chloride). Here we uncover the surface structures of chloride-adsorbed, silver-coated gold nanocrystals with {111}, {110}, {310} and {720} indexed facets by X-ray absorption spectroscopy and density functional theory modelling. The silver–chloride, silver–silver and silver–gold bonding structures are markedly different between the nanocrystal surfaces, and are sensitive to their formation mechanism and facet type. A uniquemore » approach of combining the density functional theory and experimental/simulated X-ray spectroscopy further verifies the surface structure models and identifies the previously indistinguishable valence state of silver atoms on the nanocrystal surfaces. Overall, this work elucidates the thus-far unknown chloride–metal nanocrystal surface structures and sheds light onto the halide-induced growth mechanism of anisotropic nanocrystals.« less

The Impact of Moisture Intrusions from Lower Latitudes on Arctic Net Surface Radiative Fluxes and Sea Ice Growth in Fall and Winter

NASA Astrophysics Data System (ADS)

Hegyi, B. M.; Taylor, P. C.

2017-12-01

The fall and winter seasons mark an important period in the evolution of Arctic sea ice, where energy is transferred away from the surface to facilitate the cooling of the surface and the growth of Arctic sea ice extent and thickness. Climatologically, these seasons are characterized by distinct periods of increased and reduced surface cooling and sea ice growth. Periods of reduced sea ice growth and surface cooling are associated with cloudy conditions and the transport of warm and moist air from lower latitudes, termed moisture intrusions. In the research presented, we explore the regional and Arctic-wide impact of moisture intrusions on the surface net radiative fluxes and sea ice growth for each fall and winter season from 2000/01-2015/16, utilizing MERRA2 reanalysis data, PIOMAS sea ice thickness data, and daily CERES radiative flux data. Consistent with previous studies, we find that positive anomalies in downwelling longwave surface flux are associated with increased temperature and water vapor content in the atmospheric column contained within the moisture intrusions. Interestingly, there are periods of increased downwelling LW flux anomalies that persist for one week or longer (i.e. longer than synoptic timescales) that are associated with persistent poleward flux of warm, moist air from lower latitudes. These persistent anomalies significantly reduce the regional growth of Arctic sea ice, and may in part explain the interannual variability of fall and winter Arctic sea ice growth.

Albedo feedbacks to future climate via climate change impacts on dryland biocrusts.

PubMed

Rutherford, William A; Painter, Thomas H; Ferrenberg, Scott; Belnap, Jayne; Okin, Gregory S; Flagg, Cody; Reed, Sasha C

2017-03-10

Drylands represent the planet's largest terrestrial biome and evidence suggests these landscapes have large potential for creating feedbacks to future climate. Recent studies also indicate that dryland ecosystems are responding markedly to climate change. Biological soil crusts (biocrusts) ‒ soil surface communities of lichens, mosses, and/or cyanobacteria ‒ comprise up to 70% of dryland cover and help govern fundamental ecosystem functions, including soil stabilization and carbon uptake. Drylands are expected to experience significant changes in temperature and precipitation regimes, and such alterations may impact biocrust communities by promoting rapid mortality of foundational species. In turn, biocrust community shifts affect land surface cover and roughness-changes that can dramatically alter albedo. We tested this hypothesis in a full-factorial warming (+4 °C above ambient) and altered precipitation (increased frequency of 1.2 mm monsoon-type watering events) experiment on the Colorado Plateau, USA. We quantified changes in shortwave albedo via multi-angle, solar-reflectance measurements. Warming and watering treatments each led to large increases in albedo (>30%). This increase was driven by biophysical factors related to treatment effects on cyanobacteria cover and soil surface roughness following treatment-induced moss and lichen mortality. A rise in dryland surface albedo may represent a previously unidentified feedback to future climate.

Albedo feedbacks to future climate via climate change impacts on dryland biocrusts

NASA Astrophysics Data System (ADS)

Rutherford, William A.; Painter, Thomas H.; Ferrenberg, Scott; Belnap, Jayne; Okin, Gregory S.; Flagg, Cody; Reed, Sasha C.

2017-03-01

Drylands represent the planet’s largest terrestrial biome and evidence suggests these landscapes have large potential for creating feedbacks to future climate. Recent studies also indicate that dryland ecosystems are responding markedly to climate change. Biological soil crusts (biocrusts) ‒ soil surface communities of lichens, mosses, and/or cyanobacteria ‒ comprise up to 70% of dryland cover and help govern fundamental ecosystem functions, including soil stabilization and carbon uptake. Drylands are expected to experience significant changes in temperature and precipitation regimes, and such alterations may impact biocrust communities by promoting rapid mortality of foundational species. In turn, biocrust community shifts affect land surface cover and roughness—changes that can dramatically alter albedo. We tested this hypothesis in a full-factorial warming (+4 °C above ambient) and altered precipitation (increased frequency of 1.2 mm monsoon-type watering events) experiment on the Colorado Plateau, USA. We quantified changes in shortwave albedo via multi-angle, solar-reflectance measurements. Warming and watering treatments each led to large increases in albedo (>30%). This increase was driven by biophysical factors related to treatment effects on cyanobacteria cover and soil surface roughness following treatment-induced moss and lichen mortality. A rise in dryland surface albedo may represent a previously unidentified feedback to future climate.

Albedo feedbacks to future climate via climate change impacts on dryland biocrusts

USGS Publications Warehouse

Rutherford, William A.; Painter, Thomas H.; Ferrenberg, Scott; Belnap, Jayne; Okin, Gregory S.; Flagg, Cody B.; Reed, Sasha C.

2017-01-01

Drylands represent the planet’s largest terrestrial biome and evidence suggests these landscapes have large potential for creating feedbacks to future climate. Recent studies also indicate that dryland ecosystems are responding markedly to climate change. Biological soil crusts (biocrusts) ‒ soil surface communities of lichens, mosses, and/or cyanobacteria ‒ comprise up to 70% of dryland cover and help govern fundamental ecosystem functions, including soil stabilization and carbon uptake. Drylands are expected to experience significant changes in temperature and precipitation regimes, and such alterations may impact biocrust communities by promoting rapid mortality of foundational species. In turn, biocrust community shifts affect land surface cover and roughness—changes that can dramatically alter albedo. We tested this hypothesis in a full-factorial warming (+4 °C above ambient) and altered precipitation (increased frequency of 1.2 mm monsoon-type watering events) experiment on the Colorado Plateau, USA. We quantified changes in shortwave albedo via multi-angle, solar-reflectance measurements. Warming and watering treatments each led to large increases in albedo (>30%). This increase was driven by biophysical factors related to treatment effects on cyanobacteria cover and soil surface roughness following treatment-induced moss and lichen mortality. A rise in dryland surface albedo may represent a previously unidentified feedback to future climate.

Residual contamination and corrosion on electrochemically marked uranium

NASA Astrophysics Data System (ADS)

Seals, R. D.; Bullock, J. S.; Cristy, S. S.; Bennett, R. K.

Residual contamination and potential corrosion problems on uranium parts electrochemically marked with PHB-1 and PHB-1E electroetchants have been investigated using ion microprobe mass analysis (IMMA), scanning electron microscopy (SEM), and light microscopy (LM). The effectiveness of various solvent-cleaning sequences and the influence of the use of an abrasive cleaner were evaluated. The corrosion depths and chlorine distributions resulting from the electroetching process were determined. To meet the objective, the surfaces of uranium coupons, which had been processed according to production procedures for parts, i.e., machining, cleaning, marking, inspecting and coating with Shell Vitrea-29® oil, were studied. The greater surface wetting capability of the PHB-1E electroetchant solution relative to PHB-1 resulted in less localized corrosion at the point of attack which provided a more legible mark. Components of the electroetchants (aluminum, potassium and chromium) were found in the marked areas of both types of electroetched samples. Chromium, resulting from the corrosion inhibitor in the electroetchants, was found in the etched areas as well as on the coupon away from the electroetched areas. Depth profile data indicated that the major etching action (marking thickness) of the electroetchants penetrated to a depth of approximately 200 nm. Trace amounts of chlorine were present primarily within the first 65 nm of the marked surface. Comparison of the solvent rinsing sequences revealed that the most effective cleaning process included a degreaser, such as perchloroethylene, followed by a polar solvent, such as alcohol. Evaluation of the use of an abrasive cleaner on the electroetched areas indicates that this process removed residual contaminants, increased mark legibility and did not introduce significant residuals from the abrading material or cause significant surface damage.

Effects of wind on the dynamics of the central jet during drop impact onto a deep-water surface

NASA Astrophysics Data System (ADS)

Liu, Xinan; Wang, An; Wang, Shuang; Dai, Dejun

2018-05-01

The cavity and central jet generated by the impact of a single water drop on a deep-water surface in a wind field are experimentally studied. Different experiments are performed by varying the impacting drop diameter and wind speed. The contour profile histories of the cavity (also called crater) and central jet (also called stalk) are measured in detail with a backlit cinematic shadowgraph technique. The results show that shortly after the drop hits the water surface an asymmetrical cavity appears along the wind direction, with a train of capillary waves on the cavity wall. This is followed by the formation of an inclined central jet at the location of the drop impact. It is found that the wind has little effect on the penetration depth of the cavity at the early stage of the cavity expansion, but markedly changes the capillary waves during the retraction of the cavity. The capillary waves in turn shift the position of the central jet formation leeward. The dynamics of the central jet are dominated by two mechanisms: (i) the oblique drop impact produced by the wind and (ii) the wind drag force directly acting on the jet. The maximum height of the central jet, called the stalk height, is drastically affected by the wind, and the nondimensional stalk height H /D decreases with increasing θ Re-1 , where D is the drop diameter, θ is the impingement angle of drop impact, and Re=ρaUwD /μa is the Reynolds number with air density ρa, wind speed Uw, and air viscosity μa.

Pavement marking performance analysis

DOT National Transportation Integrated Search

2009-06-30

This research evaluated pavement marking performance and developed useful degradation models for thermoplastic : and paint pavement markings which can help North Carolina meet the pending FHWA minimum retroreflectivity : requirements. The impacts of ...

A Probe for Measuring Spacecraft Surface Potentials Using a Direct-Gate Field Effect Transistor.

DTIC Science & Technology

1983-09-30

SURFACE POTENTIALS USING A DIRECT-GATE FIELD EFFECT TRANSISTOR Mark N. Horenstein Anton Havretic Trustees of Boston University 881 Commonwealth Avenue...1933 Transistor 6. PERFORMING ORG. REPORT NUMBER 7. AUTHOR(s) S. CONTRACT OR GRANT NUMBER(&) ’_5 Mark N. Horenstein Anton Mavretic F19628-82-K-00 34...at AFGL. These tests can be considered the bench mark tests for device performance, with all elements of the monitoring system optimized to eliminate

Differential actions of proteinases and neuraminidase on mammalian erythrocyte surface and its impact on erythrocyte agglutination by concanavalin A.

PubMed

Sharma, Savita; Gokhale, Sadashiv M

2012-12-01

Action of proteinases viz. trypsin and chymotrypsin, and neuraminidase on intact erythrocyte membrane proteins and glycophorins (sialoglycoproteins) exposed to cell surface and its impact on lectin (concanavalin A)-mediated agglutination were studied in Homo sapiens (human), Capra aegagrus hircus (goat) and Bubalus bubalis (buffalo). Membrane proteins and glycophorins analysis by SDS-PAGE as visualized by coomassie brilliant blue and periodic acid-schiff stains, respectively, and agglutination behaviour revealed marked differences: 1) there were prominent dissimilarities in the number and molecular weights of glycophorins in human, goat and buffalo erythrocyte membranes; 2) proteinase action(s) on human and buffalo erythrocyte surface membrane proteins and glycophorins showed similarity but was found different in goat; 3) significant differences in erythrocyte agglutinability with concanavalin A can be attributed to differences in membrane composition and alterations in the surface proteins after enzyme treatment; 4) a direct correlation was found between degradation of glycophorins and concanavalin A agglutinability; 5) action of neuraminidase specifically indicated the negative role of cell surface sialic acids in determining concanavalin A agglutinability of goat and buffalo erythrocytes, similar to human. Present studies clearly indicate that there are some basic differences in human, goat and buffalo erythrocyte membrane proteins, especially with respect to glycophorins, which determine the concanavalin A-mediated agglutination in enzyme treated erythrocytes.

Cloud Feedback Key to Marine Heatwave off Baja California

NASA Astrophysics Data System (ADS)

Myers, Timothy A.; Mechoso, Carlos R.; Cesana, Gregory V.; DeFlorio, Michael J.; Waliser, Duane E.

2018-05-01

Between 2013 and 2015, the northeast Pacific Ocean experienced the warmest surface temperature anomalies in the modern observational record. This "marine heatwave" marked a shift of Pacific decadal variability to its warm phase and was linked to significant impacts on marine species as well as exceptionally arid conditions in western North America. Here we show that the subtropical signature of this warming, off Baja California, was associated with a record deficit in the spatial coverage of co-located marine boundary layer clouds. This deficit coincided with a large increase in downwelling solar radiation that dominated the anomalous energy budget of the upper ocean, resulting in record-breaking warm sea surface temperature anomalies. Our observation-based analysis suggests that a positive cloud-surface temperature feedback was key to the extreme intensity of the heatwave. The results demonstrate the extent to which boundary layer clouds can contribute to regional variations in climate.

Recognition of Terrestrial Impact Craters with COSMO-SkyMed

NASA Astrophysics Data System (ADS)

Virelli, M.; Staffieri, S.; Battagliere, M. L.; Komatsu, G.; Di Martino, M.; Flamini, E.; Coletta, A.

2016-08-01

All bodies having a solid surface, without distinction, show, with greater or lesser evidence, the marks left by the geological processes they undergone during their evolution. There is a geomorphological feature that is evident in all the images obtained by the probes sent to explore our planetary system: impact craters.Craters formed by the impact of small cosmic bodies have dimensions ranging from some meters to hundreds of kilometers. However, for example on the Lunar regolith particles, have been observed also sub- millimeter craters caused by dust impacts. The kinetic energy of the impactor, which velocity is in general of the order of tens km/s, is released in fractions of a second, generally in a explosive way, generating complex phenomena that transform not only the morphology of the surface involved by the impact, but also the mineralogy and crystallography of the impacted material. Even our planet is not immune to these impacts. At present, more than 180 geological structures recognized as of impact origin are known on Earth.In this article, we aim to show how these impact structures on Earth's surface are observed from space. To do this, we used the images obtained by the COSMO-SkyMed satellite constellation.Starting from 2013, ASI proposed, in collaboration with the Astrophysical Observatory of Turin and University D'Annunzio of Chieti, the realization of an Encyclopedic Atlas of Terrestrial Impact Craters using COSMO-SkyMed data that will become the first atlas of all recognized terrestrial impact craters based on images acquired by a X band radar. To observe these impact craters all radar sensor modes have been used, according to the size of the analyzed crater.The project includes research of any new features that could be classified as impact craters and, for the sites whereby it is considered necessary, the implementation of a geological survey on site to validate the observations.In this paper an overview of the Atlas of Terrestrial Impact Craters using COSMO-SkyMed data, currently under review for publication, is provided.

Front lighted optical tooling method and apparatus

DOEpatents

Stone, W.J.

1983-06-30

An optical tooling method and apparatus uses a front lighted shadowgraphic technique to enhance visual contrast of reflected light. The apparatus includes an optical assembly including a fiducial mark, such as cross hairs, reflecting polarized light with a first polarization, a polarizing element backing the fiducial mark and a reflective surface backing the polarizing element for reflecting polarized light bypassing the fiducial mark and traveling through the polarizing element. The light reflected by the reflecting surface is directed through a second pass of the polarizing element toward the frontal direction with a polarization differing from the polarization of the light reflected by the fiducial mark. When used as a tooling target, the optical assembly may be mounted directly to a reference surface or may be secured in a mounting, such as a magnetic mounting. The optical assembly may also be mounted in a plane defining structure and used as a spherometer in conjunction with an optical depth measuring instrument.

The analysis of tire rubber traces collected after braking incidents using Pyrolysis-GasChromatography/Mass Spectrometry.

PubMed

Sarkissian, Garry

2007-09-01

Automobile tire marks can routinely be found at the scenes of crime, particularly hit-and-run accidents and are left on road surfaces because of sudden braking or the wheels spinning. The tire marks are left due to the friction between the tire rubber and the solid road surface, and do not always demonstrate the tire tread pattern. However, the tire mark will contain traces of the tire. In this study, Pyrolysis Gas Chromatography/Mass Spectrometry was used to analyze 12 tires from different manufacturer's and their traces collected after braking incidents. Tire marks were left on a conglomerate road surface with sudden braking. The samples were pyrolysed without removal of contaminant in a micro-furnace type pyrolyser. Quantitative and qualitative analysis were performed on all the samples. All 12 samples were distinguished from each other. Each of the tire traces were identified as coming from there original source.

[Comparison of bite marks and teeth features using 2D and 3D methods].

PubMed

Lorkiewicz-Muszyńska, Dorota; Glapiński, Mariusz; Zaba, Czesław; Łabecka, Marzena

2011-01-01

The nature of bite marks is complex. They are found at the scene of crime on different materials and surfaces - not only on human body and corpse, but also on food products and material objects. Human bites on skin are sometimes difficult to interpret and to analyze because of the specific character of skin--elastic and distortable--and because different areas of human body have different surfaces and curvatures. A bite mark left at the scene of crime can be a highly helpful way to lead investigators to criminals. The study was performed to establish: 1) whether bite marks exhibit variations in the accuracy of impressions on different materials, 2) whether it is possible to use the 3D method in the process of identifying an individual based on the comparison of bite marks revealed at the scene, and 3D scans of dental casts, 3) whether application of the 3D method allows for elimination of secondary photographic distortion of bite marks. The authors carried out experiments on simulated cases. Five volunteers bit various materials with different surfaces. Experimental bite marks were collected with emphasis on differentiations of materials. Subsequently, dental impressions were taken from five volunteers in order to prepare five sets of dental casts (the maxilla and mandible. The biting edges of teeth were impressed in wax to create an imprint. The samples of dental casts, corresponding wax bite impressions and bite marks from different materials were scanned with 2D and 3D scanners and photographs were taken. All of these were examined in detail and then compared using different methods (2D and 3D). 1) Bite marks exhibit variations in accuracy of impression on different materials. The most legible reproduction of bite marks was seen on cheese. 2) In comparison of bite marks, the 3D method and 3D scans of dental casts are highly accurate. 3) The 3D method helps to eliminate secondary photographic distortion of bite marks.

A survey of some metallographic etching reagents for restoration of obliterated engraved marks on aluminium-silicon alloy surfaces.

PubMed

Uli, Norjaidi; Kuppuswamy, R; Amran, Mohd Firdaus Che

2011-05-20

A brief survey to assess the sensitivity and efficacy of some common etching reagents for revealing obliterated engraved marks on Al-Si alloy surfaces is presented. Experimental observations have recommended use of alternate swabbing of 10% NaOH and 10% HNO(3) on the obliterated surfaces for obtaining the desired results. The NaOH etchant responsible for bringing back the original marks resulted in the deposition of some dark coating that has masked the recovered marks. The coating had been well removed by dissolving it in HNO(3) containing 10-20% acid. However, the above etching procedure was not effective on aluminium (99% purity) and Al-Zn-Mg-Cu alloy surfaces. Also the two reagents (i) immersion in 10% aq. phosphoric acid and (ii) alternate swabbing of 60% HCl and 40% NaOH suggested earlier for high strength Al-Zn-Mg-Cu alloys [23] were quite ineffective on Al-Si alloys. Thus different aluminium alloys needed different etching treatments for successfully restoring the obliterated marks. Al-Si alloys used in casting find wide applications especially in the manufacture of engine blocks of motor vehicles. Hence, the results presented in this paper are of much relevance in serial number restoration problems involving this alloy. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

16 CFR 1512.15 - Requirements for seat.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) above the top of the seat surface at the point where the seat surface is intersected by the seat post axis. This requirement does not apply to recumbent bicycles. (b) Seat post. The seat post shall contain... adjustment); the mark shall not affect the structural integrity of the seat post. This mark shall be located...

16 CFR § 1512.15 - Requirements for seat.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) above the top of the seat surface at the point where the seat surface is intersected by the seat post axis. This requirement does not apply to recumbent bicycles. (b) Seat post. The seat post shall contain... adjustment); the mark shall not affect the structural integrity of the seat post. This mark shall be located...

16 CFR 1512.15 - Requirements for seat.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) above the top of the seat surface at the point where the seat surface is intersected by the seat post axis. This requirement does not apply to recumbent bicycles. (b) Seat post. The seat post shall contain... adjustment); the mark shall not affect the structural integrity of the seat post. This mark shall be located...

The mark of vegetation change on Earth's surface energy balance: data-driven diagnostics and model validation

NASA Astrophysics Data System (ADS)

Cescatti, A.; Duveiller, G.; Hooker, J.

2017-12-01

Changing vegetation cover not only affects the atmospheric concentration of greenhouse gases but also alters the radiative and non-radiative properties of the surface. The result of competing biophysical processes on Earth's surface energy balance varies spatially and seasonally, and can lead to warming or cooling depending on the specific vegetation change and on the background climate. To date these effects are not accounted for in land-based climate policies because of the complexity of the phenomena, contrasting model predictions and the lack of global data-driven assessments. To overcome the limitations of available observation-based diagnostics and of the on-going model inter-comparison, here we present a new benchmarking dataset derived from satellite remote sensing. This global dataset provides the potential changes induced by multiple vegetation transitions on the single terms of the surface energy balance. We used this dataset for two major goals: 1) Quantify the impact of actual vegetation changes that occurred during the decade 2000-2010, showing the overwhelming role of tropical deforestation in warming the surface by reducing evapotranspiration despite the concurrent brightening of the Earth. 2) Benchmark a series of ESMs against data-driven metrics of the land cover change impacts on the various terms of the surface energy budget and on the surface temperature. We anticipate that the dataset could be also used to evaluate future scenarios of land cover change and to develop the monitoring, reporting and verification guidelines required for the implementation of mitigation plans that account for biophysical land processes.

Identification marking by means of laser peening

DOEpatents

Hackel, Lloyd A.; Dane, C. Brent; Harris, Fritz

2002-01-01

The invention is a method and apparatus for marking components by inducing a shock wave on the surface that results in an indented (strained) layer and a residual compressive stress in the surface layer. One embodiment of the laser peenmarking system rapidly imprints, with single laser pulses, a complete identification code or three-dimensional pattern and leaves the surface in a state of deep residual compressive stress. A state of compressive stress in parts made of metal or other materials is highly desirable to make them resistant to fatigue failure and stress corrosion cracking. This process employs a laser peening system and beam spatial modulation hardware or imaging technology that can be setup to impress full three dimensional patterns into metal surfaces at the pulse rate of the laser, a rate that is at least an order of magnitude faster than competing marking technologies.

Lunar Dust on Heat Rejection System Surfaces: Problems and Prospects

NASA Technical Reports Server (NTRS)

Gaier, James R.; Jaworske, Donald A.

2007-01-01

Heat rejection from power systems will be necessary for human and robotic activity on the lunar surface. Functional operation of such heat rejection systems is at risk of degradation as a consequence of dust accumulation. The Apollo astronauts encountered marked degradation of performance in heat rejection systems for the lunar roving vehicle, science packages, and other components. Although ground testing of dust mitigation concepts in support of the Apollo mission identified mitigation tools, the brush concept adopted by the Apollo astronauts proved essentially ineffective. A better understanding of the issues associated with the impact of lunar dust on the functional performance of heat rejection systems and its removal is needed as planning gets underway for human and robotic missions to the Moon. Renewed emphasis must also be placed on ground testing of pristine and dust-covered heat rejection system surfaces to quantify degradation and address mitigation concepts. This paper presents a review of the degradation in performance of heat rejection systems encountered on the lunar surface to-date, and will discuss current activities underway to evaluate the durability of candidate heat rejection system surfaces and current dust mitigation concepts.

The effect of the arbitrary level assignment of satellite cloud motion wind vectors on wind analyses in the pre-thunderstorm environment

NASA Technical Reports Server (NTRS)

Peslen, C. A.; Koch, S. E.; Uccellini, L. W.

1985-01-01

The impact of satellite-derived cloud motion vectors on SESAME rawinsonde wind fields was studied in two separate cases. The effect of wind and moisture gradients on the arbitrary assignment of the satellite data is assessed to coordinate surfaces in a severe storm environment marked by strong vertical wind shear. Objective analyses of SESAME rawinsonde winds and combined winds are produced and differences between these two analyzed fields are used to make an assessment of coordinate level choice. It is shown that the standard method of arbitrarily assigning wind vectors to a low level coordinate surface yields systematic differences between the rawinsonde and combined wind analyses. Arbitrary assignment of cloud motions to the 0.9 sigma surface produces smaller differences than assignment to the 825 mb pressure surface. Systematic differences occur near moisture discontinuities and in regions of horizontal and vertical wind shears. The differences between the combined and SESAME wind fields are made smallest by vertically interpolating cloud motions to either a pressure or sigma surface.

Restoration of engraved marks on steel surfaces by etching technique.

PubMed

Zaili, Mohd Azlan Mohd; Kuppuswamy, R; Harun, Hafizah

2007-08-24

It is known that restoration of erased engraved identification marks on the engine and the chassis of a car or on a firearm has low success rate. Unlike stamping, engraving on a metal surface leaves no pronounced, permanent subsurface deformation in the crystalline structure, also called dislocation that can be revealed by suitable methods. Hence, the current research work investigated whether metallographic reagents used in the restoration of stamp (compression) marks could be applied to recover engraved marks on steel surfaces and also to establish the sensitivity and effectiveness of some of these reagents for the restoration of the marks. Experiments were conducted by mechanically engraving alphanumeric characters on several steel plates using a computer controlled engraving machine called Gravograph. The markings were later erased from the above steel plates by removing the metal in stages of 0.01 mm through 0.04 mm below the bottom of the engraving. Several plates were thus prepared wherein each one had been abraded to a specific depth. Then eight metallographic reagents were tested on each one of the above erased plates using a swabbing technique. The results had shown that while most of the reagents were able to restore marks up to certain levels of erasure, the reagent 5 g copper sulphate, 60 ml water, 30 ml concentrated ammonium hydroxide and 60 ml concentrated hydrochloric acid restored marks erased to a depth of 0.04 mm below the engraving depth, thus presenting itself the most sensitive reagent. Quite significantly, the above reagent was also able to decipher successfully the original engraved marks that had been erased and engraved with a new number, or obliterated by centre punching. The results of this research work should benefit the forensic practitioners engaged in the serial number recovery on vehicles, firearms and other objects.

Use of LS-DYNA(Registered TradeMark) to Assess the Energy Absorption Performance of a Shell-Based Kevlar(TradeMark)/Epoxy Composite Honeycomb

NASA Technical Reports Server (NTRS)

Polanco, Michael

2010-01-01

The forward and vertical impact stability of a composite honeycomb Deployable Energy Absorber (DEA) was evaluated during a full-scale crash test of an MD-500 helicopter at NASA Langley?s Landing and Impact Research Facility. The lower skin of the helicopter was retrofitted with DEA components to protect the airframe subfloor upon impact and to mitigate loads transmitted to Anthropomorphic Test Device (ATD) occupants. To facilitate the design of the DEA for this test, an analytical study was conducted using LS-DYNA(Registered TradeMark) to evaluate the performance of a shell-based DEA incorporating different angular cell orientations as well as simultaneous vertical and forward impact conditions. By conducting this study, guidance was provided in obtaining an optimum design for the DEA that would dissipate the kinetic energy of the airframe while maintaining forward and vertical impact stability.

16 CFR 1512.15 - Requirements for seat.

Code of Federal Regulations, 2011 CFR

2011-01-01

....) above the top of the seat surface at the point where the seat surface is intersected by the seat post axis. (b) Seat post. The seat post shall contain a permanent mark or ring that clearly indicates the... integrity of the seat post. This mark shall be located no less than two seat-post diameters from the lowest...

16 CFR 1512.15 - Requirements for seat.

Code of Federal Regulations, 2010 CFR

2010-01-01

....) above the top of the seat surface at the point where the seat surface is intersected by the seat post axis. (b) Seat post. The seat post shall contain a permanent mark or ring that clearly indicates the... integrity of the seat post. This mark shall be located no less than two seat-post diameters from the lowest...

Tracking illicit small arms trafficking: implementation of Intentional Firearm Microstamping (IFM) to small arms and light weapons imports and exports

NASA Astrophysics Data System (ADS)

Lizotte, Todd E.; Ohar, Orest P.

2009-09-01

The illicit trafficking in small arms is an international problem with grave consequences to those who live in less developed nations. To stop any form of trafficking it is important to ensure the ability to track weapons to their sources, there must be a common international system for the marking and tracing of weapons. Under current international law, states may adopt various different weapons marking systems, complicating the identification of the country-of-origin of a weapon [1]. However, these marking technologies are only good for those firearms that are recovered or captured. By instituting Intentional Firearm Microstamping (IFM) a technology that provides a link to a serial or production build number, by embossing the IFM code on to the cartridge that is fired and ejected at the scene. IFM will provide critical forensic intelligence in regions of conflict by helping to identify patterns, trafficking routes and ultimately shut down illicit arms sources and markets that fuel the violence associated with regional genocide, terrorism and/or insurgency groups within warzones. Intentional Firearm Microstamping (IFM) technology will provide a rapid and accurate cartridge-to-firearm identification process, enabling law enforcement both national and international to quickly pursue international arms dealers and other illicit firearm markets. Intentional Firearm Microstamping (IFM) is a patented technology and trace solution where intentional tooling marks are formed or micromachined onto firearms interior surfaces that come into contact or impact the surfaces of cartridge casings. The IFM tooling marks can take the form of alphanumeric codes or encoded geometric codes, such as a barcode. As the firearm is discharged the intentional tooling marks transfer a code to the cartridge casing before it is ejected out of the firearm. When recovered at the scene of an incident, the intentional firearm microstamped cartridge can indentify a specific firearm, without the need to recover that firearm. This paper will explain the key attributes of Intentional Firearm Microstamping technology; including its implementation and application benefits such as developing border security controls and law enforcement capacity world wide to combat illicit trafficking of firearms to terrorists, gangs and/or fueling regional conflicts. The data generated by IFM will be discussed and its application to spatial and temporal mapping of trafficking patterns and other criminal patterns.

Direct evidence for impact winter following the Cretaceous-Paleogene bolide impact

NASA Astrophysics Data System (ADS)

Vellekoop, J.; Sluijs, A.; Smit, J.; Schouten, S.; Sinninghe Damsté, J. S.; Brinkhuis, H.

2012-12-01

The Cretaceous/Paleogene (K/Pg) boundary, ~65.5 Ma, marks a mass-extinction event related the impact of a large asteroid on the Yucatan peninsula, Mexico. Model scenarios predict that the explosive injection of dust and sulfate aerosols into the stratosphere blocked incoming solar radiation, resulting in a cooling pulse of months to several decades, a so-called 'impact winter', but thus far, proxy records lack sufficient resolution to evaluate this hypothesis. We report on a major, short-lived drop in sea surface temperatures (SSTs) recorded in an unusually well preserved and stratigraphically expanded K/Pg boundary site in Texas, USA, based on TEX86 paleothermometry. Critically, the cooling directly post-dates impact-related tsunami deposits, and coincides with the deposition of extraterrestrial iridium representing aerosol fall out, restricting the age of the cooling to the first months to decades after impact. We interpret this cooling to reflect the first direct evidence for the "impact winter" at the K/Pg boundary. The combination of darkness and cooling must have been a key contributory element in the extinctions of many biological clades, including the dinosaurs, flying reptiles and marine reptiles.

Mapping and Visualization of Storm-Surge Dynamics for Hurricane Katrina and Hurricane Rita

USGS Publications Warehouse

Gesch, Dean B.

2009-01-01

The damages caused by the storm surges from Hurricane Katrina and Hurricane Rita were significant and occurred over broad areas. Storm-surge maps are among the most useful geospatial datasets for hurricane recovery, impact assessments, and mitigation planning for future storms. Surveyed high-water marks were used to generate a maximum storm-surge surface for Hurricane Katrina extending from eastern Louisiana to Mobile Bay, Alabama. The interpolated surface was intersected with high-resolution lidar elevation data covering the study area to produce a highly detailed digital storm-surge inundation map. The storm-surge dataset and related data are available for display and query in a Web-based viewer application. A unique water-level dataset from a network of portable pressure sensors deployed in the days just prior to Hurricane Rita's landfall captured the hurricane's storm surge. The recorded sensor data provided water-level measurements with a very high temporal resolution at surveyed point locations. The resulting dataset was used to generate a time series of storm-surge surfaces that documents the surge dynamics in a new, spatially explicit way. The temporal information contained in the multiple storm-surge surfaces can be visualized in a number of ways to portray how the surge interacted with and was affected by land surface features. Spatially explicit storm-surge products can be useful for a variety of hurricane impact assessments, especially studies of wetland and land changes where knowledge of the extent and magnitude of storm-surge flooding is critical.

Characteristics of diving in radio-marked Xantus's Murrelets

USGS Publications Warehouse

Hamilton, C.D.; Golightly, R.T.; Takekawa, John Y.

2005-01-01

We monitored diving activity of radio-marked Xantus's Murrelets Synthliboramphus hypoleucus near Anacapa Island, California, during the breeding season. Thirteen radio-marked murrelets were remotely monitored from Anacapa Island with a handheld antenna and radio receiver for 29 hours in three sample periods in April and May 2003. Mean dive durations in the sample periods were 18 s ?? 2 s, 28 s ?? 2 s, and 24 s ?? 4 s, suggesting that dives were less than 21 m from the surface. Dive duration and subsequent time on the surface differed between the sample periods. Dive duration and subsequent time on the surface were not correlated in observations stratified by individual bird or by sample period. Further, dive duration and subsequent time on the surface were not correlated within foraging bouts. Dive characteristics measured near Anacapa Island suggested that Xantus's Murrelets have the ability to capture prey found at varying depths, but will feed on prey that is most available near the surface of the water.

The impact of summer rainfall on the temperature gradient along the United States-Mexico border

NASA Technical Reports Server (NTRS)

Balling, Robert C., Jr.

1989-01-01

The international border running through the Sonoran Desert in southern Arizona and northern Sonora is marked by a sharp discontinuity in albedo and grass cover. The observed differences in surface properties are a result of long-term, severe overgrazing of the Mexican lands. Recently, investigators have shown the Mexican side of the border to have higher surface and air temperatures when compared to adjacent areas in the United State. The differences in temperatures appear to be more associated with differential evapotranspiration rates than with albedo changes along the border. In this study, the impact of summer rainfall on the observed seasonal and daily gradient in maximum temperature is examined. On a seasonal time scale, the temperature gradient increases with higher moisture levels, probably due to a vegetative response on the United States' side of the border; at the daily level, the gradient in maximum temperature decreases after a rain event as evaporation rates equalize between the countries. The results suggest that temperature differences between vegetated and overgrazed landscapes in arid areas are highly dependent upon the amount of moisture available for evapotranspiration.

A reappraisal of adult thoracic surface anatomy.

PubMed

Mirjalili, S Ali; Hale, Samuel J M; Buckenham, Tim; Wilson, Ben; Stringer, Mark D

2012-10-01

Accurate surface anatomy is essential for safe clinical practice. Numerous inconsistencies in clinically important surface markings exist between and within anatomical reference texts. The aim of this study was to investigate key thoracic surface anatomical landmarks in vivo using computed tomographic (CT) imaging. High-resolution thoracic CT scans from 153 supine adults (mean age 63, range 19-89 years; 53% female) taken at end tidal inspiration were analyzed by dual consensus reporting to determine the surface anatomy of the sternal angle, central veins, heart, lungs, and diaphragm. Patients with kyphosis/scoliosis, distorting space-occupying lesions, or visceromegaly were excluded. The position of the cardiac apex, formation of the brachiocephalic veins, and vertebral levels of the sternal angle, xiphisternal joint, and aortic hiatus were consistent with commonly accepted surface markings although there was a wide range of normal variation. In contrast, common surface markings were markedly inaccurate for the following: the position of the tracheal bifurcation, aortic arch, and azygos vein termination (below the plane of the sternal angle at T5-T6 vertebral level in most individuals); the superior vena cava/right atrial junction (most often behind the fourth costal cartilage); the lower border of the lung (adjacent to T12 vertebra posteriorly); and the level at which the inferior vena cava and esophagus traverse the diaphragm (T11 in most). Surface anatomy must be reappraised using modern imaging in vivo if it is to be evidence based and fit for purpose. The effects of gender, age, posture, respiration, build, and ethnicity also deserve greater emphasis. Copyright © 2012 Wiley Periodicals, Inc.

Surface films and metallurgy related to lubrication and wear. Ph.D. Thesis - Tokyo Inst. of Technology

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1981-01-01

The nature of the tribological surface is identified and characterized with respect to adhesion, friction, wear, and lubricating properties. Surface analysis is used to identify the role of environmental constituents on tribological behavior. The effect of solid to solid interactions for metals in contact with metals, ceramics, semiconductors, carbons, and polymers is discussed. The data presented indicate that the tribological surface is markedly different than an ideal solid surface. The environment is shown to affect strongly the behavior of two solids in contact. Results also show that small amounts of alloying elements in base metals can alter markedly adhesion, friction, and wear by segregating to the solid surface.

The debate over the Cretaceous-Tertiary boundary

NASA Technical Reports Server (NTRS)

Alvarez, W.; Asaro, F.; Alvarez, L. W.; Michel, H. V.

1988-01-01

Large-body impact on the Earth is a rare but indisputable geologic process. The impact rate is approximately known from objects discovered in Earth-crossing orbits and from the statistics of craters on the Earth's surface. Tektite and microtektite strewn fields constitute unmistakable ejecta deposits that can be due only to large-body impacts. The Cretaceous-Tertiary (K-T) boundary coincides with an unusually severe biological trauma, and this stratigraphic horizon is marked on a worldwide basis by anomalous concentrations of noble metals in chondritic proportions, mineral spherules with relict quench-crystallization textures, and mineral and rock grains showing shock deformation. These features are precisely compatible with an impact origin. Although only impact explains all the types of K-T boundary evidence, the story may not be as simple as once thought. The original hypothesis envisioned one large impact, triggering one great extinction. Newer evidence hints at various complications. Different challenges are faced by the occupants of each apex of a three-cornered argument over the K-T event. Proponents of a non-impact explanation must show that the evidence fits their preferred model better than it fits the impact scenario. Proponents of the single impact-single extinction view must explain away the complications. Proponents of a more complex impact crisis must develop a reasonable scenario which honors the new evidence.

The Impact on Stakeholder Confidence of Increased Transparency in the Examination Assessment Process

ERIC Educational Resources Information Center

Bamber, Matthew

2015-01-01

A group of postgraduate accounting and finance students were asked to participate in a three-phase exercise: sit an unseen past examination question; mark a fully anonymised previous student solution (exemplar); and then mark their own work. The marking process was facilitated by explaining and discussing the marking guide, assessment systems and…

Identifying persistent and characteristic features in firearm tool marks on cartridge cases

NASA Astrophysics Data System (ADS)

Ott, Daniel; Soons, Johannes; Thompson, Robert; Song, John

2017-12-01

Recent concerns about subjectivity in forensic firearm identification have motivated the development of algorithms to compare firearm tool marks that are imparted on ammunition and to generate quantitative measures of similarity. In this paper, we describe an algorithm that identifies impressed tool marks on a cartridge case that are both consistent between firings and contribute strongly to a surface similarity metric. The result is a representation of the tool mark topography that emphasizes both significant and persistent features across firings. This characteristic surface map is useful for understanding the variability and persistence of the tool marks created by a firearm and can provide improved discrimination between the comparison scores of samples fired from the same firearm and the scores of samples fired from different firearms. The algorithm also provides a convenient method for visualizing areas of similarity that may be useful in providing quantitative support for visual comparisons by trained examiners.

Safety impact of engineering treatments on undivided rural roads.

PubMed

Pérez, I

2006-01-01

This article presents an evaluation of the safety impacts of four engineering treatments implemented in the Autonomous Community of Madrid (Spain): highway upgrading; updating and improvement of traffic signing; repainting of pavement markings and pavement resurfacings. This evaluation was carried out using the Empirical Bayes method with a comparison group. The functioning of a methodology to test the significance of the safety impact is described. The results show that highway upgrading has a positive and significant safety impact, while the updating and improvement of traffic signing, the repainting of road markings and pavement resurfacings do not exhibit a significant impact on safety.

The effect of vegetation and soil texture on the nature of organics in runoff from a catchment supplying water for domestic consumption.

PubMed

Awad, John; van Leeuwen, John; Abate, Dawit; Pichler, Markus; Bestland, Erick; Chittleborough, David J; Fleming, Nigel; Cohen, Jonathan; Liffner, Joel; Drikas, Mary

2015-10-01

The influence of vegetation and soil texture on the concentration and character of dissolved organic matter (DOM) present in runoff from the surface and sub-surface of zero order catchments of the Myponga Reservoir-catchment (South Australia) was investigated to determine the impacts of catchment characteristics and land management practices on the quality of waters used for domestic supply. Catchments selected have distinct vegetative cover (grass, native vegetation or pine) and contrasting texture of the surface soil horizon (sand or clay loam/clay). Water samples were collected from three slope positions (upper, middle, and lower) at soil depths of ~30 cm and ~60 cm in addition to overland flows. Filtered (0.45 μm) water samples were analyzed for dissolved organic carbon (DOC) and UV-visible absorbance and by F-EEM and HPSEC with UV and fluorescence detection to characterize the DOM. Surface and sub-surface runoff from catchments with clay soils and native vegetation or grass had lower DOC concentrations and lower relative abundances of aromatic, humic-like and high molecular weight organics than runoff from sandy soils with these vegetative types. Sub-surface flows from two catchments with Pinus radiata had similar DOC concentrations and DOM character, regardless of marked variation in surface soil texture. Runoff from catchments under native vegetation and grass on clay soils resulted in lower DOC concentrations and hence would be expected to have lower coagulant demand in conventional treatment for potable water supply than runoff from corresponding sandy soil catchments. However, organics in runoff from clay catchments would be more difficult to remove by coagulation. Surface waters from the native vegetation and grass catchments were generally found to have higher relative abundance of organic compounds amenable to removal by coagulation compared with sub-surface waters. Biophysical and land management practices combine to have a marked influence on the quality of source water used for domestic supply. Copyright © 2015 Elsevier B.V. All rights reserved.

How Tiny Collisions Shape Mercury

NASA Astrophysics Data System (ADS)

Kohler, Susanna

2017-07-01

If space rocks are unpleasant to encounter, space dust isnt much better. Mercurys cratered surface tells of billions of years of meteoroid impacts but its thin atmosphere is what reveals its collisional history with smaller impactors. Now new research is providing a better understanding of what were seeing.Micrometeoroids Ho!The inner solar system is bombarded by micrometeoroids, tiny particles of dust (on the scale of a tenth of a millimeter) emitted by asteroids and comets as they make their closest approach to the Sun. This dust doesnt penetrateEarths layers of atmosphere, but the innermost planet of our solar system, Mercury, doesnt have this convenient cushioning.Just as Mercury is affected by the impacts of large meteoroids, its also shaped by the many smaller-scale impacts it experiences. These tiny collisions are thought to vaporize atoms and molecules from the planets surface, which quickly dissociate. This process adds metals to Mercurys exosphere, the planets extremely tenuous atmosphere.Modeling PopulationsDistribution of the directions from which meteoroids originate before impacting Mercurys surface, as averaged over its entire orbit. Local time of 12 hr corresponds to the Sun-facing side. A significant asymmetry is seen between the dawn (6 hrs) and dusk (18 hrs) rates. [Pokorn et al. 2017]The metal distribution in the exosphere provides a way for us to measure the effect of micrometeoroid impacts on Mercury but this only works if we have accurate models of the process. A team of scientists led by Petr Pokorn (The Catholic University of America and NASA Goddard SFC) has now worked to improve our picture of micrometeoroid impact vaporization on Mercury.Pokorn and collaborators argue that two meteoroid populations Jupiter-family comets (short-period) and Halley-type comets (long-period) contribute the dust for the majority of micrometeoroid impacts on Mercury. The authors model the dynamics and evolution of these two populations, reproducing the distribution of directions from which micrometeoroids strike Mercury during its yearly orbit.Schematic of Mercury in its orbit around the Sun. The dawn side leads the orbital motion, while the dusk side trails it.Geometry of an OrbitMercurys orbit is unique in our solar system: it circles the Sun twice for every three rotations on its own axis so if you were on Mercury, youd see a single day pass over the span of two years. As with all prograde planets, the edge leading the Mercurys orbit marks the dawn terminator, while the edge trailing the planets orbital motion marks the dusk terminator.Pokorn and collaborators find a significant asymmetry in the impact vaporization that occurs on Mercurys dawn side versus its dusk side. This is due to impact geometry (since the dusk side is shielded from impacts in the direction of motion) and seasonal variation of the dust/meteoroid environment around the planet. The authors show that the source of impact vaporization shifts toward the nightside as Mercury approaches aphelion, and toward the dayside when the planet approaches the Sun.Importance of Long-Period CometsSeasonal variations of the relative vaporization rate from the authors model (black line) compared to measurements of Mercurys exospheric abundance of Ca. The contribution of long-period comets is shown by the blue line. [Pokorn et al. 2017]The dawn/dusk asymmetry and the seasonal variations predicted by the model are all nicely consistent NASAs MESSENGER spacecraft observations of the metal distribution in Mercurys exosphere.What makes Pokorn and collaborators model work so well? Their inclusion of the long-period, Halley-type comets is key: the high impact velocity of the micrometeoroids produced by this family play a significant role in shaping the impact vaporization rate of Mercurys surface.This work successfully demonstrates that we can use measurements of Mercurys exosphere as a unique tool to constrain the dust population in the inner solar system.CitationPetr Pokorn et al 2017 ApJL 842 L17. doi:10.3847/2041-8213/aa775d

Interaction of cold radiofrequency plasma with seeds of beans (Phaseolus vulgaris)

PubMed Central

Bormashenko, Edward; Shapira, Yekaterina; Grynyov, Roman; Whyman, Gene; Bormashenko, Yelena; Drori, Elyashiv

2015-01-01

The impact of cold radiofrequency air plasma on the wetting properties and water imbibition of beans (Phaseolus vulgaris) was studied. The influence of plasma on wetting of a cotyledon and seed coat (testa) was elucidated. It was established that cold plasma treatment leads to hydrophilization of the cotyledon and tissues constituting the testa when they are separately exposed to plasma. By contrast, when the entire bean is exposed to plasma treatment, only the external surface of the bean is hydrophilized by the cold plasma. Water imbibition by plasma-treated beans was studied. Plasma treatment markedly accelerates the water absorption. The crucial role of a micropyle in the process of water imbibition was established. It was established that the final percentage of germination was almost the same in the cases of plasma-treated, untreated, and vacuum-pumped samples. However, the speed of germination was markedly higher for the plasma-treated samples. The influence of the vacuum pumping involved in the cold plasma treatment on the germination was also clarified. PMID:25948708

[Interface bond and compatibility between Mark II machining ceramic and vita VM9 veneering porcelain].

PubMed

Liu, Tian-Shuang; Li, Zhen-Chun; Chen, Xiao-Dong

2009-04-01

To investigate the interface bond and thermal compatibility between Mark II machining ceramic and Vita VM9 veneering porcelain. A bar shaped specimen (30 mm x 15 mm x 1 mm in size) of Mark II block was prepared, with 0.5 mm-deep notch (vertical to the long axis of specimen) at the middle of the bottom surface. The upper surface was veneered with 0.3 mm VM9 dentin base porcelain. Then the specimen was fractured from the notching site and the fracture surface was examined under scanning electron microscope (SEM) and electron microprobe analyzer (EMPA) with electron beam of 1 microm in diameter. Another ten specimens (30 mm x 15 mm x 1.5 mm in size) were fabricated and the temperature of thermal shock resistance were tested. SEM observation showed tight bond between these two materials and EMPA results showed penetration of Al element from Mark II block into veneering porcelain and Ca element from veneering porcelain into Mark II block occurred after sintering baking. The average temperature of thermal shock resistance for specimens in this study was (194.0+/-10.3) degrees C. Cracks were mainly distributed in veneering porcelain. Chemical bond exists between the Mark II machining ceramic and Vita VM9 veneering porcelain, and there is good thermal compatibility between them.

Forensic surface metrology: tool mark evidence.

PubMed

Gambino, Carol; McLaughlin, Patrick; Kuo, Loretta; Kammerman, Frani; Shenkin, Peter; Diaczuk, Peter; Petraco, Nicholas; Hamby, James; Petraco, Nicholas D K

2011-01-01

Over the last several decades, forensic examiners of impression evidence have come under scrutiny in the courtroom due to analysis methods that rely heavily on subjective morphological comparisons. Currently, there is no universally accepted system that generates numerical data to independently corroborate visual comparisons. Our research attempts to develop such a system for tool mark evidence, proposing a methodology that objectively evaluates the association of striated tool marks with the tools that generated them. In our study, 58 primer shear marks on 9 mm cartridge cases, fired from four Glock model 19 pistols, were collected using high-resolution white light confocal microscopy. The resulting three-dimensional surface topographies were filtered to extract all "waviness surfaces"-the essential "line" information that firearm and tool mark examiners view under a microscope. Extracted waviness profiles were processed with principal component analysis (PCA) for dimension reduction. Support vector machines (SVM) were used to make the profile-gun associations, and conformal prediction theory (CPT) for establishing confidence levels. At the 95% confidence level, CPT coupled with PCA-SVM yielded an empirical error rate of 3.5%. Complementary, bootstrap-based computations for estimated error rates were 0%, indicating that the error rate for the algorithmic procedure is likely to remain low on larger data sets. Finally, suggestions are made for practical courtroom application of CPT for assigning levels of confidence to SVM identifications of tool marks recorded with confocal microscopy. Copyright © 2011 Wiley Periodicals, Inc.

Initial Testing of the Mark-0 X-Band RF Gun at SLAC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vlieks, Arnold; Adolphsen, C.; Dolgashev, V.

A new X-band RF gun (Mark-0) has been assembled, tuned and was tested in the ASTA facility at SLAC. This gun has been improved from an earlier gun used in Compton-scattering experiments at SLAC by the introduction of a racetrack dual-input coupler to reduce quadrupole fields. Waveguide-to-coupler irises were also redesigned to reduce surface magnetic fields and therefore peak pulse surface heating. Tests of this photocathode gun will allow us to gain early operational experience for beam tests of a new gun with further improvements (Mark-1) being prepared for SLAC's X-Band Test Area (XTA) program and the LLNL MEGa-ray program.more » Results of current testing up to {approx} 200 MV/m peak surface Electric fields are presented.« less

Investigation of the impact of snow removal activities on pavement markings in Virginia.

DOT National Transportation Integrated Search

1995-01-01

Snow removal activities resulted in substantial damage to pavement markings in Virginia over the last 2 years. Typically, the estimates of the extent of pavement marking damage are based on the observations of the staff of the Virginia Department of ...

Recognition in context: Implications for trade mark law.

PubMed

Humphreys, Michael S; McFarlane, Kimberley A; Burt, Jennifer S; Kelly, Sarah J; Weatherall, Kimberlee G; Burrell, Robert G

2017-10-01

Context effects in recognition have played a major role in evaluating theories of recognition. Understanding how context impacts recognition is also important for making sound trade mark law. Consumers attempting to discriminate between the brand they are looking for and a look-alike product often have to differentiate products which share a great deal of common context: positioning on the supermarket shelf, the type of store, aspects of the packaging, or brand claims. Trade mark and related laws aim to protect brands and reduce consumer confusion, but courts assessing allegations of trade mark infringement often lack careful empirical evidence concerning the impact of brand and context similarity, and, in the absence of such evidence, make assumptions about how consumers respond to brands that downplay the importance of context and focus on the similarity of registered marks. The experiments reported in this paper aimed to test certain common assumptions in trade mark law, providing evidence that shared context can cause mistakes even where brand similarity is low.

The Mekong at climatic crossroads: Lessons from the geological past.

PubMed

Penny, Dan

2008-05-01

The wetlands of the lower Mekong River Basin are ecologically and socioeconomically significant, but they are threatened by predicted climatic change. The likely response of wetland ecosystems to altered flooding regimes and surface-water chemistry is unknown in detail and difficult to model. One way of exploring the impact of climate change on wetland ecosystems is to utilize proxy environmental data that reveal patterns of change over geological time. In recent years, the coverage and resolution of proxy climatic data have improved markedly in the region. Recent evidence of the South China Sea transgression into southern and central Cambodia and paleobotanical evidence from the Tonle Sap ("Great Lake") and elsewhere allow us to explore how periods of higher-than-present sea level and increased monsoon rainfall in the past have impacted the wetland ecology of the lower Mekong River Basin.

Active thermography and post-processing image enhancement for recovering of abraded and paint-covered alphanumeric identification marks

NASA Astrophysics Data System (ADS)

Montanini, R.; Quattrocchi, A.; Piccolo, S. A.

2016-09-01

Alphanumeric marking is a common technique employed in industrial applications for identification of products. However, the realised mark can undergo deterioration, either by extensive use or voluntary deletion (e.g. removal of identification numbers of weapons or vehicles). For recovery of the lost data many destructive or non-destructive techniques have been endeavoured so far, which however present several restrictions. In this paper, active infrared thermography has been exploited for the first time in order to assess its effectiveness in restoring paint covered and abraded labels made by means of different manufacturing processes (laser, dot peen, impact, cold press and scribe). Optical excitation of the target surface has been achieved using pulse (PT), lock-in (LT) and step heating (SHT) thermography. Raw infrared images were analysed with a dedicated image processing software originally developed in Matlab™, exploiting several methods, which include thermographic signal reconstruction (TSR), guided filtering (GF), block guided filtering (BGF) and logarithmic transformation (LN). Proper image processing of the raw infrared images resulted in superior contrast and enhanced readability. In particular, for deeply abraded marks, good outcomes have been obtained by application of logarithmic transformation to raw PT images and block guided filtering to raw phase LT images. With PT and LT it was relatively easy to recover labels covered by paint, with the latter one providing better thermal contrast for all the examined targets. Step heating thermography never led to adequate label identification instead.

33 CFR 118.160 - Vertical clearance gauges.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the foot marks, read from top to bottom. Each gauge must be installed on the end of the right... directly on the bridge channel pier or pier protection structure if the surface is suitable and has... be marked by black numerals and foot marks on a white background. Paint, if used, must be of good...

33 CFR 118.160 - Vertical clearance gauges.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of the foot marks, read from top to bottom. Each gauge must be installed on the end of the right... directly on the bridge channel pier or pier protection structure if the surface is suitable and has... be marked by black numerals and foot marks on a white background. Paint, if used, must be of good...

9 CFR 310.6 - Carcasses and parts passed for cooking; marking.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Carcasses and parts passed for cooking... INSPECTION AND CERTIFICATION POST-MORTEM INSPECTION § 310.6 Carcasses and parts passed for cooking; marking. Carcasses and parts passed for cooking shall be marked conspicuously on the surface tissues thereof by a...

Urbanization Impacts on River Landscapes in a Global Context

NASA Astrophysics Data System (ADS)

Chin, A.

2005-12-01

A half century ago, Strahler (1956) and Leopold (1956) pointed attention to the reality of human impacts on river systems, outlining erosion and aggradation as system responses when steady state is disturbed by human activity, and linking river channel adjustments to changes in sediment yield owing to land use alterations. Significant advances have been made along these lines in the years since, with intensified research efforts producing a voluminous literature documenting a range of human impacts on fluvial geomorphology. This paper summarizes the progress made on understanding the impacts of urban development on river landscapes, with emphasis on the distribution of such impacts in a global context. Drawing from a database developed from published literature representing a range of world areas, the analysis quantifies the magnitude and direction of urban-induced change in a comparative context, evaluates how impacts vary with locale and scale, and assesses the persistence of such impacts across locales and scales. Results indicate high variability both in magnitude and persistence of impacts. The spatial distribution of research investigations has also been markedly uneven, with input to theory development having come from a limited number of sites. Substantial areas across the earth surface remain blind spots in this context; future investigations might serve the science best if they are conducted in some of these locations.

Fabrics coated with lubricated nanostructures display robust omniphobicity

DOE PAGES

Shillingford, Cicely; MacCallum, Noah; Wong, Tak -Sing; ...

2013-12-11

The development of a stain-resistant and pressure-stable textile is desirable for consumer and industrial applications alike, yet it remains a challenge that current technologies have been unable to fully address. Traditional superhydrophobic surfaces, inspired by the lotus plant, are characterized by two main components: hydrophobic chemical functionalization and surface roughness. While this approach produces water-resistant surfaces, these materials have critical weaknesses that hinder their practical utility, in particular as robust stain-free fabrics. For example, traditional superhydrophobic surfaces fail (i.e., become stained) when exposed to low-surface-tension liquids, under pressure when impacted by a high-velocity stream of water (e.g., rain), and whenmore » exposed to physical forces such as abrasion and twisting. We have recently introduced slippery lubricant-infused porous surfaces (SLIPS), a self-healing, pressure-tolerant and omniphobic surface, to address these issues. However we present the rational design and optimization of nanostructured lubricant-infused fabrics and demonstrate markedly improved performance over traditional superhydrophobic textile treatments: SLIPS-functionalized cotton and polyester fabrics exhibit decreased contact angle hysteresis and sliding angles, omni-repellent properties against various fluids including polar and nonpolar liquids, pressure tolerance and mechanical robustness, all of which are not readily achievable with the state-of-the-art superhydrophobic coatings.« less

Fabrics coated with lubricated nanostructures display robust omniphobicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shillingford, C; MacCallum, N; Wong, TS

2013-12-11

The development of a stain-resistant and pressure-stable textile is desirable for consumer and industrial applications alike, yet it remains a challenge that current technologies have been unable to fully address. Traditional superhydrophobic surfaces, inspired by the lotus plant, are characterized by two main components: hydrophobic chemical functionalization and surface roughness. While this approach produces water-resistant surfaces, these materials have critical weaknesses that hinder their practical utility, in particular as robust stain-free fabrics. For example, traditional superhydrophobic surfaces fail (i.e., become stained) when exposed to low-surface-tension liquids, under pressure when impacted by a high-velocity stream of water (e. g., rain), andmore » when exposed to physical forces such as abrasion and twisting. We have recently introduced slippery lubricant-infused porous surfaces (SLIPS), a self-healing, pressure-tolerant and omniphobic surface, to address these issues. Herein we present the rational design and optimization of nanostructured lubricant-infused fabrics and demonstrate markedly improved performance over traditional superhydrophobic textile treatments: SLIPS-functionalized cotton and polyester fabrics exhibit decreased contact angle hysteresis and sliding angles, omni-repellent properties against various fluids including polar and nonpolar liquids, pressure tolerance and mechanical robustness, all of which are not readily achievable with the state-of-the-art superhydrophobic coatings.« less

Fabrics coated with lubricated nanostructures display robust omniphobicity.

PubMed

Shillingford, Cicely; MacCallum, Noah; Wong, Tak-Sing; Kim, Philseok; Aizenberg, Joanna

2014-01-10

The development of a stain-resistant and pressure-stable textile is desirable for consumer and industrial applications alike, yet it remains a challenge that current technologies have been unable to fully address. Traditional superhydrophobic surfaces, inspired by the lotus plant, are characterized by two main components: hydrophobic chemical functionalization and surface roughness. While this approach produces water-resistant surfaces, these materials have critical weaknesses that hinder their practical utility, in particular as robust stain-free fabrics. For example, traditional superhydrophobic surfaces fail (i.e., become stained) when exposed to low-surface-tension liquids, under pressure when impacted by a high-velocity stream of water (e.g., rain), and when exposed to physical forces such as abrasion and twisting. We have recently introduced slippery lubricant-infused porous surfaces (SLIPS), a self-healing, pressure-tolerant and omniphobic surface, to address these issues. Herein we present the rational design and optimization of nanostructured lubricant-infused fabrics and demonstrate markedly improved performance over traditional superhydrophobic textile treatments: SLIPS-functionalized cotton and polyester fabrics exhibit decreased contact angle hysteresis and sliding angles, omni-repellent properties against various fluids including polar and nonpolar liquids, pressure tolerance and mechanical robustness, all of which are not readily achievable with the state-of-the-art superhydrophobic coatings.

Fabrics coated with lubricated nanostructures display robust omniphobicity

NASA Astrophysics Data System (ADS)

Shillingford, Cicely; MacCallum, Noah; Wong, Tak-Sing; Kim, Philseok; Aizenberg, Joanna

2014-01-01

The development of a stain-resistant and pressure-stable textile is desirable for consumer and industrial applications alike, yet it remains a challenge that current technologies have been unable to fully address. Traditional superhydrophobic surfaces, inspired by the lotus plant, are characterized by two main components: hydrophobic chemical functionalization and surface roughness. While this approach produces water-resistant surfaces, these materials have critical weaknesses that hinder their practical utility, in particular as robust stain-free fabrics. For example, traditional superhydrophobic surfaces fail (i.e., become stained) when exposed to low-surface-tension liquids, under pressure when impacted by a high-velocity stream of water (e.g., rain), and when exposed to physical forces such as abrasion and twisting. We have recently introduced slippery lubricant-infused porous surfaces (SLIPS), a self-healing, pressure-tolerant and omniphobic surface, to address these issues. Herein we present the rational design and optimization of nanostructured lubricant-infused fabrics and demonstrate markedly improved performance over traditional superhydrophobic textile treatments: SLIPS-functionalized cotton and polyester fabrics exhibit decreased contact angle hysteresis and sliding angles, omni-repellent properties against various fluids including polar and nonpolar liquids, pressure tolerance and mechanical robustness, all of which are not readily achievable with the state-of-the-art superhydrophobic coatings.

The slip resistance of common footwear materials measured with two slipmeters.

PubMed

Chang, W R; Matz, S

2001-12-01

The slip resistance of 16 commonly used footwear materials was measured with the Brungraber Mark II and the English XL on 3 floor surfaces under surface conditions of dry, wet, oily and oily wet. Three samples were used for each material combination and surface condition. The results of a one way ANOVA analysis indicated that the differences among different samples were statistically significant for a large number of material combinations and surface conditions. The results indicated that the ranking of materials based on their slip resistance values depends highly on the slipmeters, floor surfaces and surface conditions. For contaminated surfaces including wet, oily and oily wet surfaces, the slip resistance obtained with the English XL was usually higher than that measured with the Brungraber Mark II. The correlation coefficients between the slip resistance obtained with these two slipmeters calculated for different surface conditions indicated a strong correlation with statistical significance.

Acute myeloid leukemia stem cell markers in prognosis and targeted therapy: potential impact of BMI-1, TIM-3 and CLL-1.

PubMed

Darwish, Noureldien H E; Sudha, Thangirala; Godugu, Kavitha; Elbaz, Osama; Abdelghaffar, Hasan A; Hassan, Emad E A; Mousa, Shaker A

2016-09-06

Acute myeloid leukemia (AML) patients show high relapse rates and some develop conventional chemotherapy resistance. Leukemia Stem Cells (LSCs) are the main player for AML relapses and drug resistance. LSCs might rely on the B-cell-specific Moloney murine leukemia virus integration site-1 (BMI-1) in promoting cellular proliferation and survival. Growth of LSCs in microenvironments that are deprived of nutrients leads to up-regulation of the signaling pathways during the progression of the disease, which may illustrate the sensitivity of LSCs to inhibitors of those signaling pathways as compared to normal cells. We analyzed the expression of LSC markers (CD34, CLL-1, TIM-3 and BMI-1) using quantitative RT-PCR in bone marrow samples of 40 AML patients of different FAB types (M1, M2, M3, M4, M5, and M7). We also studied the expression of these markers in 2 AML cell lines (Kasumi-1 and KG-1a) using flow cytometry and quantitative RT-PCR. The overexpression of TIM-3, CLL-1, and BMI-1 was markedly correlated with poor prognosis in these patients. Our in vitro findings demonstrate that targeting BMI-1, which markedly increased in the leukemic cells, was associated with marked decrease in leukemic burden. This study also presents results for blocking LSCs' surface markers CD44, CLL-1, and TIM-3. These markers may play an important role in elimination of AML. Our study indicates a correlation between the expression of markers TIM-3, CLL-1, and especially of BMI-1 and the aggressiveness of AML and thus the potential impact of prognosis and therapies that target LSCs on improving the cure rates.

Examining the Tension between Academic Standards and Inclusion for Disabled Students: The Impact on Marking of Individual Academics' Frameworks for Assessment

ERIC Educational Resources Information Center

Ashworth, Mary; Bloxham, Sue; Pearce, Leonie

2010-01-01

This article draws on developing theory regarding assessment and marking to explore the impact of staff values regarding widening participation on grading decisions. It reports on an innovative creative arts module delivered for students with complex disabilities. Data collection included observation of teaching, interviews with staff, students…

A Brief Study on Toxic Combustion Products of the Polymers Used in High-Pressure Oxygen Systems

NASA Technical Reports Server (NTRS)

Hshieh, Fu-Yu; Beeson, Harold D.

2005-01-01

One likely cause of polymer ignition in a high-pressure oxygen system is the adiabatic-compression heating of polymers caused by pneumatic impact. Oxidative pyrolysis or combustion of polymers in a high-pressure oxygen system could generate toxic gases. This paper investigates the feasibility of using the NASA pneumatic-impact system to conduct adiabatic-compression combustion tests and determines the toxic combustion products produced from the burning of five selected polymers. Five polymers commonly used in high-pressure oxygen systems, Zytel(Registered TradeMark) 42 (Nylon 6/6), Buna N (nitrile rubber), Witon(Registered TradeMark) A (copolymer of vinylidene fluoride and hexafluoropropylene), Neoflon(Registered TradeMark) (polychlorotrifluoroethylene), and Teflon(Registered TradeMark) (polytetrafluoroethylene), were tested in the NASA pneumatic-impact test system at 17.2-MPa oxygen pressure. The polymers were ignited and burned; combustion products were collected in a stainless-steel sample bottle and analyzed using various methods. The results show that the NASA pneumatic-impact system is an appropriate test system to conduct adiabatic-compression combustion tests and to collect combustion products for further chemical analysis. The composition of the combustion product gas generated from burning the five selected polymers are presented and discussed.

EFFECTS OF FEATHER CRYSTALS IN THE MACROSTRUCTURE ON EARING BEHAVIOR AND ELOXAL STRUCTURE OF SHEETS OF PURE ALUMINUM (in German)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zieger, H.

1961-10-01

The as-cast structure of d.c.-cast aluminum ingots sometimes shows feather-like crystals. The influence of this type of crystals on the earing behavior and on the surface markings after anodizing was investigated on Al 99.5- sheets of 2 mm thickness. Feather-like crystals gave rise to more irregular and higher earings in all cases. Hot and afterwards cold rolled sheets showed markings on the anodized surface, which were intensified by feather-like crystals in the ingot. Extruding prior to hot rolling suppressed these markings completely, but did not affect the earing behavior. (auth)

Methods and computer executable instructions for marking a downhole elongate line and detecting same

DOEpatents

Watkins, Arthur D.

2003-05-13

Methods and computer executable instructions are provided for making an elongate line (22) with a plurality of marks (30) and detecting those marks (30) to determine a distance of the elongate line (22) in a downhole or a physical integrity thereof. In a preferred embodiment, each mark comprises a plurality of particles (44) having a substantially permanent magnetizing capability adhered to an exterior surface of the elongate line (22) at preselected intervals with an epoxy paint. The particles (44) are arranged at each interval as a plurality of bands (40). Thereafter, the particles are oriented into a magnetic signature for that interval by magnetizing the particles to create a magnetic field substantially normal to the exterior surface. This facilitates detection by a Hall effect probe. The magnetic signatures are stored in a computing configuration and, once a mark is detected, a correlation is made to a unique position on the elongate line by comparison with the stored magnetic signatures. Preferred particles include samarium-cobalt and neodymium-iron-boride.

Objective analysis of toolmarks in forensics

NASA Astrophysics Data System (ADS)

Grieve, Taylor N.

Since the 1993 court case of Daubert v. Merrell Dow Pharmaceuticals, Inc. the subjective nature of toolmark comparison has been questioned by attorneys and law enforcement agencies alike. This has led to an increased drive to establish objective comparison techniques with known error rates, much like those that DNA analysis is able to provide. This push has created research in which the 3-D surface profile of two different marks are characterized and the marks' cross-sections are run through a comparative statistical algorithm to acquire a value that is intended to indicate the likelihood of a match between the marks. The aforementioned algorithm has been developed and extensively tested through comparison of evenly striated marks made by screwdrivers. However, this algorithm has yet to be applied to quasi-striated marks such as those made by the shear edge of slip-joint pliers. The results of this algorithm's application to the surface of copper wire will be presented. Objective mark comparison also extends to comparison of toolmarks made by firearms. In an effort to create objective comparisons, microstamping of firing pins and breech faces has been introduced. This process involves placing unique alphanumeric identifiers surrounded by a radial code on the surface of firing pins, which transfer to the cartridge's primer upon firing. Three different guns equipped with microstamped firing pins were used to fire 3000 cartridges. These cartridges are evaluated based on the clarity of their alphanumeric transfers and the clarity of the radial code surrounding the alphanumerics.

9 CFR 310.6 - Carcasses and parts passed for cooking; marking.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Carcasses and parts passed for cooking; marking. 310.6 Section 310.6 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF.... Carcasses and parts passed for cooking shall be marked conspicuously on the surface tissues thereof by a...

9 CFR 310.6 - Carcasses and parts passed for cooking; marking.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Carcasses and parts passed for cooking; marking. 310.6 Section 310.6 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF.... Carcasses and parts passed for cooking shall be marked conspicuously on the surface tissues thereof by a...

9 CFR 310.6 - Carcasses and parts passed for cooking; marking.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Carcasses and parts passed for cooking; marking. 310.6 Section 310.6 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF.... Carcasses and parts passed for cooking shall be marked conspicuously on the surface tissues thereof by a...

9 CFR 310.6 - Carcasses and parts passed for cooking; marking.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Carcasses and parts passed for cooking; marking. 310.6 Section 310.6 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF.... Carcasses and parts passed for cooking shall be marked conspicuously on the surface tissues thereof by a...

Impact of board-marker accuracy on lumber yield

Treesearch

Urs Buehlmann; R. Edward Thomas

2003-01-01

The production of wooden furniture parts, mouldings, and flooring requires the removal of unacceptable character marks (also called "defects") such as holes, rot, knots, etc., from boards. The majority of the wood processing industry manually identifies such unusable areas and marks them with fluorescent crayons. Automated saws scan these marks and computers...

Tropical cyclone rainfall area controlled by relative sea surface temperature

PubMed Central

Lin, Yanluan; Zhao, Ming; Zhang, Minghua

2015-01-01

Tropical cyclone rainfall rates have been projected to increase in a warmer climate. The area coverage of tropical cyclones influences their impact on human lives, yet little is known about how tropical cyclone rainfall area will change in the future. Here, using satellite data and global atmospheric model simulations, we show that tropical cyclone rainfall area is controlled primarily by its environmental sea surface temperature (SST) relative to the tropical mean SST (that is, the relative SST), while rainfall rate increases with increasing absolute SST. Our result is consistent with previous numerical simulations that indicated tight relationships between tropical cyclone size and mid-tropospheric relative humidity. Global statistics of tropical cyclone rainfall area are not expected to change markedly under a warmer climate provided that SST change is relatively uniform, implying that increases in total rainfall will be confined to similar size domains with higher rainfall rates. PMID:25761457

[Inventory of regional surface nutrient balance and policy recommendations in China].

PubMed

Chen, Min-Peng; Chen, Ji-Ning

2007-06-01

By applying OECD surface soil nitrogen balance methodology, the framework, methodology and database for nutrient balance budget in China are established to evaluate the impact of nutrient balance on agricultural production and water environment. Results show that nitrogen and phosphorus surplus in China are 640 x 10(4) t and 98 x 10(4) t respectively, and nitrogen and phosphorus surplus intensity in China are 16.56 kg/hm2 and 2.53 kg/hm2 respectively. Because of striking spatial difference of nutrient balance across the country, China is seeing a dual-challenge of nutrient surplus management as well as nutrient deficit management. Chemical fertilizer and livestock manure are best targets to perform nutrient surplus management due to their marked contributions to nutrient input. However, it is not cost-effective to implement a uniform management for all regions since nutrient input structures of them vary considerably.

Role of tool marks inside spherical mitigation pit fabricated by micro-milling on repairing quality of damaged KH2PO4 crystal

PubMed Central

Chen, Ming-Jun; Cheng, Jian; Yuan, Xiao-Dong; Liao, Wei; Wang, Hai-Jun; Wang, Jing-He; Xiao, Yong; Li, Ming-Quan

2015-01-01

Repairing initial slight damage site into stable structures by engineering techniques is the leading strategy to mitigate the damage growth on large-size components used in laser-driven fusion facilities. For KH2PO4 crystals, serving as frequency converter and optoelectronic switch-Pockels cell, micro-milling has been proven the most promising method to fabricate these stable structures. However, tool marks inside repairing pit would be unavoidably introduced due to the wearing of milling cutter in actual repairing process. Here we quantitatively investigate the effect of tool marks on repairing quality of damaged crystal components by simulating its induced light intensification and testing the laser-induced damage threshold. We found that due to the formation of focusing hot spots and interference ripples, the light intensity is strongly enhanced with the presence of tool marks, especially for those on rear surfaces. Besides, the negative effect of tool marks is mark density dependent and multiple tool marks would aggravate the light intensification. Laser damage tests verified the role of tool marks as weak points, reducing the repairing quality. This work offers new criterion to comprehensively evaluate the quality of repaired optical surfaces to alleviate the bottleneck issue of low laser damage threshold for optical components in laser-driven fusion facilities. PMID:26399624

Evaluation of two methods for monitoring surface cleanliness-ATP bioluminescence and traditional hygiene swabbing.

PubMed

Davidson, C A; Griffith, C J; Peters, A C; Fielding, L M

1999-01-01

The minimum bacterial detection limits and operator reproducibility of the Biotrace Clean-Tracetrade mark Rapid Cleanliness Test and traditional hygiene swabbing were determined. Areas (100 cm2) of food grade stainless steel were separately inoculated with known levels of Staphylococcus aureus (NCTC 6571) and Escherichia coli (ATCC 25922). Surfaces were sampled either immediately after inoculation while still wet, or after 60 min when completely dry. For both organisms the minimum detection limit of the ATP Clean-Tracetrade mark Rapid Cleanliness Test was 10(4) cfu/100 cm2 (p < 0.05) and was the same for wet and dry surfaces. Both organism type and surface status (i.e. wet or dry) influenced the minimum detection limits of hygiene swabbing, which ranged from 10(2) cfu/100 cm2 to >10(7) cfu/100 cm2. Hygiene swabbing percentage recovery rates for both organisms were less than 0.1% for dried surfaces but ranged from 0.33% to 8.8% for wet surfaces. When assessed by six technically qualified operators, the Biotrace Clean-Tracetrade mark Rapid Cleanliness Test gave superior reproducibility for both clean and inoculated surfaces, giving mean coefficients of variation of 24% and 32%, respectively. Hygiene swabbing of inoculated surfaces gave a mean CV of 130%. The results are discussed in the context of hygiene monitoring within the food industry. Copyright 1999 John Wiley & Sons, Ltd.

Research notes : methods for traffic stripe removal.

DOT National Transportation Integrated Search

2001-11-01

Pavement marking removal due to changed traffic configurations is a continual construction and maintenance problem. Often the removal alters the texture and/or color of the pavement surface. The removed markings become visible under different lightin...

Development of a mobile toolmark characterization/comparison system [Development of a mobile, automated toolmark characterization/comparison system

DOE PAGES

Chumbley, Scott; Zhang, Song; Morris, Max; ...

2016-11-16

Since the development of the striagraph, various attempts have been made to enhance forensic investigation through the use of measuring and imaging equipment. This study describes the development of a prototype system employing an easy-to-use software interface designed to provide forensic examiners with the ability to measure topography of a toolmarked surface and then conduct various comparisons using a statistical algorithm. Acquisition of the data is carried out using a portable 3D optical profilometer, and comparison of the resulting data files is made using software named “MANTIS” (Mark and Tool Inspection Suite). The system has been tested on laboratory-produced markingsmore » that include fully striated marks (e.g., screwdriver markings), quasistriated markings produced by shear-cut pliers, impression marks left by chisels, rifling marks on bullets, and cut marks produced by knives. Using the system, an examiner has the potential to (i) visually compare two toolmarked surfaces in a manner similar to a comparison microscope and (ii) use the quantitative information embedded within the acquired data to obtain an objective statistical comparison of the data files. Finally, this study shows that, based on the results from laboratory samples, the system has great potential for aiding examiners in conducting comparisons of toolmarks.« less

Development of a mobile toolmark characterization/comparison system [Development of a mobile, automated toolmark characterization/comparison system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chumbley, Scott; Zhang, Song; Morris, Max

Since the development of the striagraph, various attempts have been made to enhance forensic investigation through the use of measuring and imaging equipment. This study describes the development of a prototype system employing an easy-to-use software interface designed to provide forensic examiners with the ability to measure topography of a toolmarked surface and then conduct various comparisons using a statistical algorithm. Acquisition of the data is carried out using a portable 3D optical profilometer, and comparison of the resulting data files is made using software named “MANTIS” (Mark and Tool Inspection Suite). The system has been tested on laboratory-produced markingsmore » that include fully striated marks (e.g., screwdriver markings), quasistriated markings produced by shear-cut pliers, impression marks left by chisels, rifling marks on bullets, and cut marks produced by knives. Using the system, an examiner has the potential to (i) visually compare two toolmarked surfaces in a manner similar to a comparison microscope and (ii) use the quantitative information embedded within the acquired data to obtain an objective statistical comparison of the data files. Finally, this study shows that, based on the results from laboratory samples, the system has great potential for aiding examiners in conducting comparisons of toolmarks.« less

Paint Pavement Marking Performance Prediction Model That Includes the Impacts of Snow Removal Operations

DTIC Science & Technology

2011-03-01

Hypothesized that snow plows wear down mountain road pavement markings. 2007 Craig et al. -Edge lines degrade slower than center/skip lines 2007...retroreflectivity to create the models. They discovered that paint pavement markings last 80% longer on Portland Cement Concrete than Asphalt Concrete at low AADT...retroreflectivity, while yellow markings lost 21%. Lu and Barter attributed the sizable degradation to snow removal, sand application, and studded

Measurement of surface tension and viscosity by open capillary techniques

DOEpatents

Rye,Robert R. , Yost,Frederick G.

1998-01-01

An open-channel capillary is provided, having preferably a v-shaped groove in a flat wettable surface. The groove has timing marks and a source marker in which the specimen to be tested is deposited. The time of passage between the timing marks is recorded, and the ratio of surface tension .gamma. to viscosity .mu. is determined from the equation given below: ##EQU1## where h.sub.0 is the groove depth, .alpha. is the groove angle, .theta. is the liquid/solid contact angle, and t is the flow time. It has been shown by the

49 CFR 172.304 - Marking requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... be durable, in English and printed on or affixed to the surface of a package or on a label, tag, or... labels or attachments; and (4) Must be located away from any other marking (such as advertising) that...

Validation of tool mark analysis of cut costal cartilage.

PubMed

Love, Jennifer C; Derrick, Sharon M; Wiersema, Jason M; Peters, Charles

2012-03-01

This study was designed to establish the potential error rate associated with the generally accepted method of tool mark analysis of cut marks in costal cartilage. Three knives with different blade types were used to make experimental cut marks in costal cartilage of pigs. Each cut surface was cast, and each cast was examined by three analysts working independently. The presence of striations, regularity of striations, and presence of a primary and secondary striation pattern were recorded for each cast. The distance between each striation was measured. The results showed that striations were not consistently impressed on the cut surface by the blade's cutting edge. Also, blade type classification by the presence or absence of striations led to a 65% misclassification rate. Use of the classification tree and cross-validation methods and inclusion of the mean interstriation distance decreased the error rate to c. 50%. © 2011 American Academy of Forensic Sciences.

Social Impacts of the Marking Scheme in Public Housing in Hong Kong

ERIC Educational Resources Information Center

Yau, Yung

2012-01-01

To improve environmental hygiene in public housing estates in Hong Kong, the Housing Department launched the Marking Scheme for Tenancy Enforcement in Public Housing Estates in 2003. The marking scheme operates as a penalty-point system where sitting tenants will be expelled from their public housing units if they receive penalty points up to a…

Analysis of the convergence rules of full-range PSD surface error of magnetorheological figuring KDP crystal.

PubMed

Chen, Shaoshan; He, Deyu; Wu, Yi; Chen, Huangfei; Zhang, Zaijing; Chen, Yunlei

2016-10-01

A new non-aqueous and abrasive-free magnetorheological finishing (MRF) method is adopted for processing potassium dihydrogen phosphate (KDP) crystal due to its low hardness, high brittleness, temperature sensitivity, and water solubility. This paper researches the convergence rules of the surface error of an initial single-point diamond turning (SPDT)-finished KDP crystal after MRF polishing. Currently, the SPDT process contains spiral cutting and fly cutting. The main difference of these two processes lies in the morphology of intermediate-frequency turning marks on the surface, which affects the convergence rules. The turning marks after spiral cutting are a series of concentric circles, while the turning marks after fly cutting are a series of parallel big arcs. Polishing results indicate that MRF polishing can only improve the low-frequency errors (L>10  mm) of a spiral-cutting KDP crystal. MRF polishing can improve the full-range surface errors (L>0.01  mm) of a fly-cutting KDP crystal if the polishing process is not done more than two times for single surface. We can conclude a fly-cutting KDP crystal will meet better optical performance after MRF figuring than a spiral-cutting KDP crystal with similar initial surface performance.

On the sensitivity of some common metallographic reagents to restoring obliterated marks on medium carbon (0.31% C) steel surfaces.

PubMed

Yin, Siaw Hui; Kuppuswamy, R

2009-01-10

Chemical etching, which is the most sensitive method to recover obliterated serial numbers on metal surfaces, has been practised quite successfully in forensic science laboratories all over the world. A large number of etchants suitable for particular metal surfaces based on empirical studies is available in the literature. This article reviews the sensitivity and efficacy of some popular etchants for recovering obliterated marks on medium carbon steel (0.31% C with ferrite-pearlite microstructure) used in automobile parts. The experiments involved engraving these carbon steel plates with some alphanumeric characters using a computer controlled machine "Gravograph" and erasing them to several depths below the bottom of their engraving depth. Seven metallographic reagents of which most of them were copper containing compounds were chosen for etching. The erased plates were etched with every one of these etchants using swabbing method. The results have revealed that Fry's reagent comprising cupric chloride 90 g, hydrochloric acid 120 mL and water 100mL provided the necessary contrast and was concluded to be the most sensitive. The same reagent was recommended by earlier workers for revealing strain lines in steel surfaces. Earlier, another reagent containing 5 g copper sulphate, 60 mL water, 30 mL (conc.) ammonium hydroxide, and 60 mL (conc.) hydrochloric acid was proved to be more sensitive to restore erased marks on low carbon steel (0.1% C with ferrite-pearlite structure) [M.A.M. Zaili, R. Kuppuswamy, H. Harun, Restoration of engraved marks on steel surfaces by etching technique, Forensic Sci. Int. 171 (2007) 27-32]. Thus the sensitivity of the etching reagent on steel surfaces appeared to be dependent on the content of carbon in the steel.

Detection of nitro-organic and peroxide explosives in latent fingermarks by DART- and SALDI-TOF-mass spectrometry.

PubMed

Rowell, Frederick; Seviour, John; Lim, Angelina Yimei; Elumbaring-Salazar, Cheryl Grace; Loke, Jason; Ma, Jan

2012-09-10

The ability of two mass spectrometric methods, surface-assisted laser desorption/ionization-time of flight-mass spectrometry (SALDI-TOF-MS) and direct analysis in real time (DART-MS), to detect the presence of seven common explosives (six nitro-organic- and one peroxide-type) in spiked latent fingermarks has been examined. It was found that each explosive could be detected with nanogram sensitivity for marks resulting from direct finger contact with a glass probe by DART-MS or onto stainless steel target plates using SALDI-TOF-MS for marks pre-dusted with one type of commercial black magnetic powder. These explosives also could be detected in latent marks lifted from six common surfaces (paper, plastic bag, metal drinks can, wood laminate, adhesive tape and white ceramic tile) whereas no explosive could be detected in equivalent pre-dusted marks on the surface of a commercial lifting tape by the DART-MS method due to high background interference from the tape material. The presence of TNT and Tetryl could be detected in pre-dusted latent fingermarks on a commercial lifting tape for up to 29 days sealed and stored under ambient conditions. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Simulating forensic casework scenarios in experimental studies: The generation of footwear marks in blood.

PubMed

McElhone, Rachel L; Meakin, Georgina E; French, James C; Alexander, Tracy; Morgan, Ruth M

2016-07-01

A study was designed to investigate the effects of external variables, including blood type, flooring surface, footwear tread depth and blood dryness, on the appearance of blood-based footwear marks, with particular reference to simulating a specific casework scenario. Results showed that footwear marks left in human blood tended to be of greater quality than those in equine blood, highlighting a potential issue in applying data generated with equine blood to human bloodstains in casework. Footwear tread effects were also dependent on blood type, but the type of flooring surface did not affect the appearance of the mark. Under some conditions, as the blood dried, the amount of detail retained from footwear contact decreased. These results provide the beginnings of an empirical evidence base to allow a more accurate interpretation of blood-based footwear marks in forensic casework. When applied to a disputed bloodstain in a specific case, these results also demonstrate the importance of such experiments in narrowing the range of explanations possible in the interpretation of forensic evidence. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Instruments for Reading Direct-Marked Data-Matrix Symbols

NASA Technical Reports Server (NTRS)

Schramm, Harry F.; Corder, Eric L.

2006-01-01

Improved optoelectronic instruments (specially configured digital cameras) for reading direct-marked data-matrix symbols on the surfaces of optically reflective objects (including specularly reflective ones) are undergoing development. Data-matrix symbols are two-dimensional binary patterns that are used, like common bar codes, for automated identification of objects. The first data-matrix symbols were checkerboard-like patterns of black-and-white rectangles, typically existing in the forms of paint, ink, or detachable labels. The major advantage of direct marking (the marks are more durable than are painted or printed symbols or detachable labels) is offset by a major disadvantage (the marks generated by some marking methods do not provide sufficient contrast to be readable by optoelectronic instruments designed to read black-and-white data-matrix symbols). Heretofore, elaborate lighting, lensing, and software schemes have been tried in efforts to solve the contrast problem in direct-mark matrix- symbol readers. In comparison with prior readers based on those schemes, the readers now undergoing development are expected to be more effective while costing less. All of the prior direct-mark matrix-symbol readers are designed to be aimed perpendicularly to marked target surfaces, and they tolerate very little angular offset. However, the reader now undergoing development not only tolerates angular offset but depends on angular offset as a means of obtaining the needed contrast, as described below. The prototype reader (see Figure 1) includes an electronic camera in the form of a charge-coupled-device (CCD) image detector equipped with a telecentric lens. It also includes a source of collimated visible light and a source of collimated infrared light for illuminating a target. The visible and infrared illumination complement each other: the visible illumination is more useful for aiming the reader toward a target, while the infrared illumination is more useful for reading symbols on highly reflective surfaces. By use of beam splitters, the visible and infrared collimated lights are introduced along the optical path of the telecentric lens, so that the target is illuminated and viewed from the same direction.

Effects of irradiation distance on supply of reactive oxygen species to the bottom of a Petri dish filled with liquid by an atmospheric O{sub 2}/He plasma jet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawasaki, Toshiyuki, E-mail: kawasaki@nbu.ac.jp; Kusumegi, Shota; Kudo, Akihiro

The impact of irradiation distances on plasma jet-induced specific effects on the supply of reactive oxygen species (ROS) to the bottom of a Petri dish filled with liquid was investigated using a KI-starch gel reagent that can be employed as a ROS indicator even in water. O{sub 3} exposure experiments without plasma irradiation were also performed to elucidate the specific effects of the plasma jet. Relative concentrations of ROS transported to the bottom were evaluated using absorbance measurements. The results indicated that ROS supply to the bottom is markedly enhanced by the plasma jet irradiation at shorter irradiation distances, whereasmore » similar results could not be obtained for the O{sub 3} exposure. In these cases, the liquid mixing in the depth direction was also enhanced by the plasma jet irradiation only, and the supply of reactive atomic oxygen to the liquid surface was markedly increased as well.« less

Effects of Core-Shell Rubber (CSR) Nanoparticles on the Cryogenic Fracture Toughness of CSR Modified Epoxy

NASA Technical Reports Server (NTRS)

Wang, Jun; Magee, Daniel; Schneider, Judy; Cannon, Seth

2009-01-01

This study investigated the effects of core-shell rubber (CSR) nanoparticles on the mechanical properties and fracture toughness of an epoxy resin at ambient and liquid nitrogen (LN2) temperatures. Varying amounts of Kane Ace(Registered TradeMark) MX130 and Kane Ace(Registered TradeMark) MX960 toughening agent were added to a commercially available EPON 862/Epikure W epoxy resin. Elastic modulus was calculated using quasi-static tensile data. Fracture toughness was evaluated by the resulting breaking energy measured in Charpy impact tests conducted on an instrumented drop tower. The size and distribution of the CSR nanoparticles were characterized using Transmission Electron Microscopy (TEM) and Small Angle X-ray Scattering (SAXS). Scanning Electron Microscopy (SEM) was used to study the fracture surface morphology. The addition of the CSR nanoparticles increased the breaking energy with negligible change in elastic modulus and ultimate tensile stress (UTS). At ambient temperature the breaking energy increased with increasing additions of the CSR nanoparticles up to 13.8wt%, while at LN2 temperatures, it reached a plateau at much lower CSR concentration.

Impact of air pollution on floral morphology of Cassia siamea Lamk.

PubMed

Chauhan, S V S; Chaurasia, Bharati; Rana, Anita

2004-07-01

Cassia siamea plants growing at two different sites (polluted and non-polluted) on two important roads of Agra city exhibited significant differences in their flowering phenology and floral morphology. The flowering in plants growing at polluted site is delayed and there was a marked reduction in flowering density, flowering period, size of floral parts, pollen fertility, fruit and seed-set. SEM observations revealed the presence of well developed glandular structures and reduction in the number and size of large stomata on the anther surface at polluted site. These changes were found to be closely associated with the extent of air pollution caused mainly by significant in the number of automobiles.

Colliding worlds: A journey in time and space through the solar system (Farinella Prize Lecture)

NASA Astrophysics Data System (ADS)

Marchi, S.

2017-09-01

The evolution of the interiors, surfaces, and atmospheres of solid bodies in the solar system is affected by interplanetary collisions. From Mercury to the outskirts of the solar system, collisions with leftover planetesimals -asteroids, comets and their debris- provide a primary evolutionary process. Impact craters mark this evolution and provide a diagnostic tool, which coupled with modeling and, when possible, sample analysis, allow us to unravel the ancient history of the solar system. In this prize talk, I will present a few selected cutting-edge research topics at the frontier between modeling and space exploration that without any doubt would have deeply interested the curious mind of Paolo Farinella.

The Interrelations of Features of Questions, Mark Schemes and Examinee Responses and Their Impact upon Marker Agreement

ERIC Educational Resources Information Center

Black, Beth; Suto, Irenka; Bramley, Tom

2011-01-01

In this paper we develop an evidence-based framework for considering many of the factors affecting marker agreement in GCSEs and A levels. A logical analysis of the demands of the marking task suggests a core grouping comprising: (i) question features; (ii) mark scheme features; and (iii) examinee response features. The framework synthesises…

Automatic Extraction of Road Markings from Mobile Laser Scanning Data

NASA Astrophysics Data System (ADS)

Ma, H.; Pei, Z.; Wei, Z.; Zhong, R.

2017-09-01

Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS) and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS) system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

Development of an Impervious-Surface Database for the Little Blackwater River Watershed, Dorchester County, Maryland

USGS Publications Warehouse

Milheim, Lesley E.; Jones, John W.; Barlow, Roger A.

2007-01-01

Many agricultural and forested areas in proximity to National Wildlife Refuges (NWR) are under increasing economic pressure for commercial or residential development. The upper portion of the Little Blackwater River watershed - a 27 square mile area within largely low-lying Dorchester County, Maryland, on the eastern shore of the Chesapeake Bay - is important to the U.S. Fish and Wildlife Service (USFWS) because it flows toward the Blackwater National Wildlife Refuge (BNWR), and developmental impacts of areas upstream from the BNWR are unknown. One of the primary concerns for the Refuge is how storm-water runoff may affect living resources downstream. The Egypt Road project (fig. 1), for which approximately 600 residential units have been approved, has the potential to markedly change the land use and land cover on the west bank of the Little Blackwater River. In an effort to limit anticipated impacts, the Maryland Department of Natural Resources (Maryland DNR) recently decided to purchase some of the lands previously slated for development. Local topography, a high water table (typically 1 foot or less below the land surface), and hydric soils present a challenge for the best management of storm-water flow from developed surfaces. A spatial data coordination group was formed by the Dorchester County Soil and Conservation District to collect data to aid decisionmakers in watershed management and on the possible impacts of development on this watershed. Determination of streamflow combined with land cover and impervious-surface baselines will allow linking of hydrologic and geologic factors that influence the land surface. This baseline information will help planners, refuge managers, and developers discuss issues and formulate best management practices to mitigate development impacts on the refuge. In consultation with the Eastern Region Geospatial Information Office, the dataset selected to be that baseline land cover source was the June-July 2005 National Agricultural Imagery Program (NAIP) 1-meter resolution orthoimagery of Maryland. This publicly available, statewide dataset provided imagery corresponding to the closest in time to the installation of a U.S. Geological Survey (USGS) Water Resources Discipline gaging station on the Little Blackwater River. It also captures land cover status just before major residential development occurs. This document describes the process used to create a database of impervious surfaces for the Little Blackwater watershed.

The Cretaceous-Tertiary (K/T) impact: One or more source craters?

NASA Technical Reports Server (NTRS)

Koeberl, Christian

1992-01-01

The Cretaceous-Tertiary (K/T) boundary is marked by signs of a worldwide catastrophe, marking the demise of more than 50 percent of all living species. Ever since Alvarez et al. found an enrichment of IR and other siderophile elements in rocks marking the K/T boundary and interpreted it as the mark of a giant asteroid (or comet) impact, scientists have tried to understand the complexities of the K/T boundary event. The impact theory received a critical boost by the discovery of shocked minerals that have so far been found only in association with impact craters. One of the problems of the K/T impact theory was, and still is, the lack of an adequate large crater that is close to the maximum abundance of shocked grains in K/T boundary sections, which was found to occur in sections in Northern America. The recent discovery of impact glasses from a K/T section in Haiti has been crucial in establishing a connection with documented impact processes. The location of the impact-glass findings and the continental nature of detritus found in all K/T sections supports at least one impact site near the North American continent. The Manson Impact Structure is the largest recognized in the United States, 35 km in diameter, and has a radiometric age indistinguishable from that of the Cretaceous-Tertiary (K/T) boundary. Although the Manson structure may be too small, it may be considered at least one element of the events that led to the catastrophic loss of life and extinction of many species at that time. A second candidate for the K/T boundary crater is the Chicxulub structure, which was first suggested to be an impact crater more than a decade ago. Only recently, geophysical studies and petrological (as well as limited chemical) analyses have indicated that this buried structure may in fact be of impact origin. At present we can conclude that the Manson crater is the only confirmed crater of K/T age, but Chicxulub is becoming a strong contender; however, detailed geochemical, geochronological, and isotopic data are necessary to provide definitive evidence.

The Cretaceous-Tertiary (K/T) impact: One or more source craters?

NASA Astrophysics Data System (ADS)

Koeberl, Christian

The Cretaceous-Tertiary (K/T) boundary is marked by signs of a worldwide catastrophe, marking the demise of more than 50 percent of all living species. Ever since Alvarez et al. found an enrichment of IR and other siderophile elements in rocks marking the K/T boundary and interpreted it as the mark of a giant asteroid (or comet) impact, scientists have tried to understand the complexities of the K/T boundary event. The impact theory received a critical boost by the discovery of shocked minerals that have so far been found only in association with impact craters. One of the problems of the K/T impact theory was, and still is, the lack of an adequate large crater that is close to the maximum abundance of shocked grains in K/T boundary sections, which was found to occur in sections in Northern America. The recent discovery of impact glasses from a K/T section in Haiti has been crucial in establishing a connection with documented impact processes. The location of the impact-glass findings and the continental nature of detritus found in all K/T sections supports at least one impact site near the North American continent. The Manson Impact Structure is the largest recognized in the United States, 35 km in diameter, and has a radiometric age indistinguishable from that of the Cretaceous-Tertiary (K/T) boundary. Although the Manson structure may be too small, it may be considered at least one element of the events that led to the catastrophic loss of life and extinction of many species at that time. A second candidate for the K/T boundary crater is the Chicxulub structure, which was first suggested to be an impact crater more than a decade ago. Only recently, geophysical studies and petrological (as well as limited chemical) analyses have indicated that this buried structure may in fact be of impact origin. At present we can conclude that the Manson crater is the only confirmed crater of K/T age, but Chicxulub is becoming a strong contender; however, detailed geochemical, geochronological, and isotopic data are necessary to provide definitive evidence.

GABAB receptor cell surface export is controlled by an endoplasmic reticulum gatekeeper

PubMed Central

Doly, Stéphane; Shirvani, Hamasseh; Gäta, Gabriel; Meye, Frank; Emerit, Michel-Boris; Enslen, Hervé; Achour, Lamia; Pardo-Lopez, Liliana; Kwon, Yang Seung; Armand, Vincent; Gardette, Robert; Giros, Bruno; Gassmann, Martin; Bettler, Bernhard; Mameli, Manuel; Darmon, Michèle; Marullo, Stefano

2016-01-01

Summary Endoplasmic reticulum (ER) release and cell surface export of many G protein-coupled receptors (GPCRs), are tightly regulated. For GABAB receptors of GABA, the major mammalian inhibitory neurotransmitter, the ligand-binding GB1 subunit is maintained in the ER by unknown mechanisms in the absence of hetero-dimerization with the GB2 subunit. We report that GB1 retention is regulated by a specific gatekeeper, PRAF2. This ER resident transmembrane protein binds to GB1, preventing its progression in the biosynthetic pathway. GB1 release occurs upon competitive displacement from PRAF2 by GB2. PRAF2 concentration, relative to that of GB1 and GB2, tightly controls cell surface receptor density and controls GABAB function in neurons. Experimental perturbation of PRAF2 levels in vivo caused marked hyperactivity disorders in mice. These data reveal an unanticipated major impact of specific ER gate-keepers on GPCR function and identify PRAF2 as a new molecular target with therapeutic potential for psychiatric and neurological diseases involving GABAB function. PMID:26033241

Green Power Partner Mark Use and Display Guidelines

EPA Pesticide Factsheets

The U.S. EPA's Green Power Partnership is a voluntary program designed to reduce the environmental impact of electricity generation by promoting renewable energy. This page contains the guidelines for use of the Green Power Partnership mark.

Topography measurements and applications in ballistics and tool mark identifications*

PubMed Central

Vorburger, T V; Song, J; Petraco, N

2016-01-01

The application of surface topography measurement methods to the field of firearm and toolmark analysis is fairly new. The field has been boosted by the development of a number of competing optical methods, which has improved the speed and accuracy of surface topography acquisitions. We describe here some of these measurement methods as well as several analytical methods for assessing similarities and differences among pairs of surfaces. We also provide a few examples of research results to identify cartridge cases originating from the same firearm or tool marks produced by the same tool. Physical standards and issues of traceability are also discussed. PMID:27182440

Impact of anthropogenic aerosols from global, East Asian, and non-East Asian sources on East Asian summer monsoon system

NASA Astrophysics Data System (ADS)

Wang, Qiuyan; Wang, Zhili; Zhang, Hua

2017-01-01

The impact of the total effects due to anthropogenic aerosols from global, East Asian, and non-East Asian sources on East Asian summer monsoon (EASM) system is studied using an aerosol-climate online model BCC_AGCM2.0.1_CUACE/Aero. The results show that the summer mean net all-sky shortwave fluxes averaged over East Asian monsoon region (EAMR) at the top of the atmosphere (TOA) and surface reduce by 4.8 and 5.0 W m- 2, respectively, due to the increases of global aerosol emissions in 2000 relative to 1850. Changes in radiations and their resulting changes in heat and water transport and cloud fraction contribute together to the surface cooling over EAMR in summer. The increases in global anthropogenic aerosols lead to a decrease of 2.1 K in summer mean surface temperature and an increase of 0.4 hPa in summer mean surface pressure averaged over EAMR, respectively. It is shown that the changes in surface temperature and pressure are significantly larger over land than ocean, thus decreasing the contrast of land-sea surface temperature and pressure. This results in the marked anomalies of north and northeast winds over eastern and southern China and the surrounding oceans in summer, thereby weakening the EASM. The summer mean precipitation averaged over the EAMR reduces by 12%. The changes in non-East Asian aerosol emissions play a more important role in inducing the changes of local temperature and pressure, and thus significantly exacerbate the weakness of the EASM circulation due to local aerosol changes. The weakening of circulation due to both is comparable, and even the effect of non-local aerosols is larger in individual regions. The changes of local and non-local aerosols contribute comparably to the reductions in precipitation over oceans, whereas cause opposite changes over eastern China. Our results highlight the importance of aerosol changes outside East Asia in the impact of the changes of anthropogenic aerosols on EASM.

Human cytomegalovirus alters localization of MHC class II and dendrite morphology in mature Langerhans cells.

PubMed

Lee, Andrew W; Hertel, Laura; Louie, Ryan K; Burster, Timo; Lacaille, Vashti; Pashine, Achal; Abate, Davide A; Mocarski, Edward S; Mellins, Elizabeth D

2006-09-15

Hemopoietic stem cell-derived mature Langerhans-type dendritic cells (LC) are susceptible to productive infection by human CMV (HCMV). To investigate the impact of infection on this cell type, we examined HLA-DR biosynthesis and trafficking in mature LC cultures exposed to HCMV. We found decreased surface HLA-DR levels in viral Ag-positive as well as in Ag-negative mature LC. Inhibition of HLA-DR was independent of expression of unique short US2-US11 region gene products by HCMV. Indeed, exposure to UV-inactivated virus, but not to conditioned medium from infected cells, was sufficient to reduce HLA-DR on mature LC, implicating particle binding/penetration in this effect. Reduced surface levels reflected an altered distribution of HLA-DR because total cellular HLA-DR was not diminished. Accumulation of HLA-DR was not explained by altered cathepsin S activity. Mature, peptide-loaded HLA-DR molecules were retained within cells, as assessed by the proportion of SDS-stable HLA-DR dimers. A block in egress was implicated, as endocytosis of surface HLA-DR was not increased. Immunofluorescence microscopy corroborated the intracellular retention of HLA-DR and revealed markedly fewer HLA-DR-positive dendritic projections in infected mature LC. Unexpectedly, light microscopic analyses showed a dramatic loss of the dendrites themselves and immunofluorescence revealed that cytoskeletal elements crucial for the formation and maintenance of dendrites are disrupted in viral Ag-positive cells. Consistent with these dendrite effects, HCMV-infected mature LC exhibit markedly reduced chemotaxis in response to lymphoid chemokines. Thus, HCMV impedes MHC class II molecule trafficking, dendritic projections, and migration of mature LC. These changes likely contribute to the reduced activation of CD4+ T cells by HCMV-infected mature LC.

Protective Performance of Plate-Cell Rubber Tiles against Childhood Head Injury on Playground Surfaces — A Finite Element Analysis

NASA Astrophysics Data System (ADS)

Chang, Li-Tung; Huang, Tsai-Jeon

Rubber tiles are commonly used in playgrounds as protective surfacing to reduce the incidence of head injuries in children caused by falling from equipment. This study developed a rubber tile model consisting of a surface layer of solid and a base layer of plate-cell and used it to investigate head injury protective performance. An explicit finite element method based on the experimental data was used to simulate head impact on the rubber tile. The peak acceleration and head injury criterion (HIC) were employed to assess the shock-absorbing capability of the tile. The results showed that compared to the peak acceleration, use of the HIC index provided a more conservative assessment of the shock absorption ability, and ultimately the protection against head injuries. This study supports the feasibility of using rubber tile with plate-cell construction to improve shock-absorbing capability. The plate-cell structure provided an excellent cushioning effect via a lower axial shear stiffness of the surface layer and lower transverse shearing stiffness of the core. The core's dimensions were an important parameter in determining the shearing stiffness. The analysis suggested that the cushioning effect would significantly reduce the peak force on the head from a fall and delay the occurrence of the peak value during impact, resulting in a marked reduction in the peak acceleration and HIC values of the head. Two plate-cell constructions with honeycomb and box-like cores were proposed and validated in this study. The better protective ability of the honeycomb core was attributed to its lower transverse shearing stiffness.

Item Unique Identification Capability Expansion: Established Process Analysis, Cost Benefit Analysis, and Optimal Marking Procedures

DTIC Science & Technology

2014-12-01

chemical etching EDM electrical discharge machine EID enterprise identifier EOSS Engineering Operational Sequencing System F Fahrenheit...Center in Corona , California, released a DoN IUID Marking Guide, which made recommendations on how to mark legacy items. It provides technical...uploaded into the IUID registry managed by the Naval Surface Warfare Center (NSWC) in Corona , California. There is no set amount of information

16 CFR 1505.7 - Maximum acceptable surface temperatures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (as described—in § 1505.6 (g)(2)) Thermal inertia type 1 Temperatures °C. °F. A 1 50 122 A 2 55 131 A... 60 140 D marked 2 75 167 D marked 3 100 212 D marked 4 125 257 E (2) (3) (3) 1 Thermal inertia types... inertia of a material can be obtained by multiplying the thermal conductivity (cal./cm./sec./degrees C...

16 CFR 1505.7 - Maximum acceptable surface temperatures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (as described—in § 1505.6 (g)(2)) Thermal inertia type 1 Temperatures °C. °F. A 1 50 122 A 2 55 131 A... 60 140 D marked 2 75 167 D marked 3 100 212 D marked 4 125 257 E (2) (3) (3) 1 Thermal inertia types... inertia of a material can be obtained by multiplying the thermal conductivity (cal./cm./sec./degrees C...

16 CFR 1505.7 - Maximum acceptable surface temperatures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (as described—in § 1505.6 (g)(2)) Thermal inertia type 1 Temperatures °C. °F. A 1 50 122 A 2 55 131 A... 60 140 D marked 2 75 167 D marked 3 100 212 D marked 4 125 257 E (2) (3) (3) 1 Thermal inertia types... inertia of a material can be obtained by multiplying the thermal conductivity (cal./cm./sec./degrees C...

16 CFR 1505.7 - Maximum acceptable surface temperatures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (as described—in § 1505.6 (g)(2)) Thermal inertia type 1 Temperatures °C. °F. A 1 50 122 A 2 55 131 A... 60 140 D marked 2 75 167 D marked 3 100 212 D marked 4 125 257 E (2) (3) (3) 1 Thermal inertia types... inertia of a material can be obtained by multiplying the thermal conductivity (cal./cm./sec./degrees C...

Virtual Tool Mark Generation for Efficient Striation Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ekstrand, Laura; Zhang, Song; Grieve, Taylor

2014-02-16

This study introduces a tool mark analysis approach based upon 3D scans of screwdriver tip and marked plate surfaces at the micrometer scale from an optical microscope. An open-source 3D graphics software package is utilized to simulate the marking process as the projection of the tip's geometry in the direction of tool travel. The edge of this projection becomes a virtual tool mark that is compared to cross-sections of the marked plate geometry using the statistical likelihood algorithm introduced by Chumbley et al. In a study with both sides of six screwdriver tips and 34 corresponding marks, the method distinguishedmore » known matches from known nonmatches with zero false-positive matches and two false-negative matches. For matches, it could predict the correct marking angle within ±5–10°. Individual comparisons could be made in seconds on a desktop computer, suggesting that the method could save time for examiners.« less

Flight set 360L007 (STS-33R) field joint protection system, thermal protection system, and systems tunnel components, volume 7

NASA Technical Reports Server (NTRS)

1990-01-01

The performance of the thermal protection system, field joint protection system, and systems tunnel components of flight set 360L007 is presented as evaluated by postflight hardware inspection. The condition of both motors was similar to previous flights. Four aft edge strikes were noted on the ground environment instrumentation thermal protection system. The hits all left a clean substrate, indicating that the damage was caused by nozzle severance debris and/or water impact. No National Space Transportation System debris criteria for missing thermal protection system were violated. Two problem reports were written against the field joint protection system. The first concerned two cracks in the K5NA closeout over the trunnion/vent valve location on the left-hand aft field joint. A similar condition was observed on Flight 5 (360H005). The second problem report referred to a number of small surface cracks between two impact marks on the left-hand forward field joint. Neither area exhibited loose material or any abnormal heat effects, and they have no impact on flight safety.

Global geologic map of Ganymede

USGS Publications Warehouse

Collins, Geoffrey C.; Patterson, G. Wesley; Head, James W.; Pappalardo, Robert T.; Prockter, Louise M.; Lucchitta, Baerbel K.; Kay, Johnathan P.

2014-01-01

Ganymede is the largest satellite of Jupiter, and its icy surface has been formed through a variety of impact cratering, tectonic, and possibly cryovolcanic processes. The history of Ganymede can be divided into three distinct phases: an early phase dominated by impact cratering and mixing of non-ice materials in the icy crust, a phase in the middle of its history marked by great tectonic upheaval, and a late quiescent phase characterized by a gradual drop in heat flow and further impact cratering. Images of Ganymede suitable for geologic mapping were collected during the flybys of Voyager 1 and Voyager 2 (1979), as well as during the Galileo Mission in orbit around Jupiter (1995–2003). This map represents a synthesis of our understanding of Ganymede geology after the conclusion of the Galileo Mission. We summarize the properties of the imaging dataset used to construct the map, previously published maps of Ganymede, our own mapping rationale, and the geologic history of Ganymede. Additional details on these topics, along with detailed descriptions of the type localities for the material units, may be found in the companion paper to this map (Patterson and others, 2010).

Identifying Severe Weather Impacts and Damage with Google Earth Engine

NASA Astrophysics Data System (ADS)

Molthan, A.; Burks, J. E.; Bell, J. R.

2015-12-01

Hazards associated with severe convective storms can lead to rapid changes in land surface vegetation. Depending upon the type of vegetation that has been impacted, their impacts can be relatively short lived, such as damage to seasonal crops that are eventually removed by harvest, or longer-lived, such as damage to a stand of trees or expanse of forest that require several years to recover. Since many remote sensing imagers provide their highest spatial resolution bands in the red and near-infrared to support monitoring of vegetation, these impacts can be readily identified as short-term and marked decreases in common vegetation indices such as NDVI, along with increases in land surface temperature that are observed at a reduced spatial resolution. The ability to identify an area of vegetation change is improved by understanding the conditions that are normal for a given time of year and location, along with a typical range of variability in a given parameter. This analysis requires a period of record well beyond the availability of near real-time data. These activities would typically require an analyst to download large volumes of data from sensors such as NASA's MODIS (aboard Terra and Aqua) or higher resolution imagers from the Landsat series of satellites. Google's Earth Engine offers a "big data" solution to these challenges, by providing a streamlined API and option to process the period of record of NASA MODIS and Landsat products through relatively simple Javascript coding. This presentation will highlight efforts to date in using Earth Engine holdings to produce vegetation and land surface temperature anomalies that are associated with damage to agricultural and other vegetation caused by severe thunderstorms across the Central and Southeastern United States. Earth Engine applications will show how large data holdings can be used to map severe weather damage, ascertain longer-term impacts, and share best practices learned and challenges with applying Earth Engine holdings to the analysis of severe weather damage. Other applications are also demonstrated, such as use of Earth Engine to prepare pre-event composites that can be used to subjectively identify other severe weather impacts. Future extension to flooding and wildfires is also proposed.

Objective analysis of toolmarks in forensics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grieve, Taylor N.

2013-01-01

Since the 1993 court case of Daubert v. Merrell Dow Pharmaceuticals, Inc. the subjective nature of toolmark comparison has been questioned by attorneys and law enforcement agencies alike. This has led to an increased drive to establish objective comparison techniques with known error rates, much like those that DNA analysis is able to provide. This push has created research in which the 3-D surface profile of two different marks are characterized and the marks’ cross-sections are run through a comparative statistical algorithm to acquire a value that is intended to indicate the likelihood of a match between the marks. Themore » aforementioned algorithm has been developed and extensively tested through comparison of evenly striated marks made by screwdrivers. However, this algorithm has yet to be applied to quasi-striated marks such as those made by the shear edge of slip-joint pliers. The results of this algorithm’s application to the surface of copper wire will be presented. Objective mark comparison also extends to comparison of toolmarks made by firearms. In an effort to create objective comparisons, microstamping of firing pins and breech faces has been introduced. This process involves placing unique alphanumeric identifiers surrounded by a radial code on the surface of firing pins, which transfer to the cartridge’s primer upon firing. Three different guns equipped with microstamped firing pins were used to fire 3000 cartridges. These cartridges are evaluated based on the clarity of their alphanumeric transfers and the clarity of the radial code surrounding the alphanumerics.« less

Group in-course assessment promotes cooperative learning and increases performance.

PubMed

Pratten, Margaret K; Merrick, Deborah; Burr, Steven A

2014-01-01

The authors describe and evaluate a method to motivate medical students to maximize the effectiveness of dissection opportunities by using In-Course-Assessments (ICAs) to encourage teamwork. A student's final mark was derived by combining the group dissection mark, group mark for questions, and their individual question mark. An analysis of the impact of the ICA was performed by comparing end of module practical summative marks in student cohorts who had, or had not, participated in the ICAs. Summative marks were compared by two-way ANOVA followed by Dunnets test, or by repeated measures ANOVA, as appropriate. A cohort of medical students was selected that had experienced both practical classes without (year one) and with the new ICA structure (year two). Comparison of summative year one and year two marks illustrated an increased improvement in year two performance in this cohort. A significant increase was also noted when comparing this cohort with five preceding year two cohorts who had not experienced the ICAs (P <0.0001). To ensure that variation in the practical summative examination was not impacting on the data, a comparison was made between three cohorts who had performed the same summative examination. Results show that students who had undertook weekly ICAs showed significantly improved summative marks, compared with those who did not (P <0.0001). This approach to ICA promotes engagement with learning resources in an active, team-based, cooperative learning environment. © 2013 American Association of Anatomists.

The Effect of Language Learning Strategies on Proficiency, Attitudes and School Achievement.

PubMed

Habók, Anita; Magyar, Andrea

2017-01-01

This study examines language learning strategy (LLS) use in connexion with foreign language attitude, proficiency and general school achievement among lower secondary students in Years 5 and 8 ( n = 868) in Hungary. An adapted version of the Strategies Inventory for Language Learning questionnaire was used for data collection. The results showed that Hungarian students mainly engage in metacognitive strategies in both years. Differences between more and less proficient language learners' strategy use have also been found. With regard to the effect of LLS on foreign language attitude, the foreign language mark and school achievement, path analysis indicated a good fit in both years. The metacognitive, social and memory strategies primarily influenced foreign language attitudes and marks in Year 5. The metacognitive strategies had a slight impact on school achievement as well as on foreign language marks. We demonstrated the dominant effect of metacognitive strategies and the low effect of memory strategies in Year 8. In addition, metacognitive strategies also influenced foreign language marks. The effect of foreign language marks on school achievement was also remarkable. There was a strong impact on the children's attitudes through these variables.

Concealed wire tracing apparatus

DOEpatents

Kronberg, J.W.

1994-05-31

An apparatus and method that combines a signal generator and a passive signal receiver to detect and record the path of partially or completely concealed electrical wiring without disturbing the concealing surface is disclosed. The signal generator applies a series of electrical pulses to the selected wiring of interest. The applied pulses create a magnetic field about the wiring that can be detected by a coil contained within the signal receiver. An audible output connected to the receiver and driven by the coil reflects the receivers position with respect to the wiring. The receivers audible signal is strongest when the receiver is directly above the wiring and the long axis of the receivers coil is parallel to the wiring. A marking means is mounted on the receiver to mark the location of the wiring as the receiver is directed over the wiring's concealing surface. Numerous marks made on various locations of the concealing surface will trace the path of the wiring of interest. 4 figs.

Impact Theory of Mass Extinctions and the Invertebrate Fossil Record

NASA Astrophysics Data System (ADS)

Alvarez, Walter; Kauffman, Erle G.; Surlyk, Finn; Alvarez, Luis W.; Asaro, Frank; Michel, Helen V.

1984-03-01

There is much evidence that the Cretaceous-Tertiary boundary was marked by a massive meteorite impact. Theoretical consideration of the consequences of such an impact predicts sharp extinctions in many groups of animals precisely at the boundary. Paleontological data clearly show gradual declines in diversity over the last 1 to 10 million years in various invertebrate groups. Reexamination of data from careful studies of the best sections shows that, in addition to undergoing the decline, four groups (ammonites, cheilostomate bryozoans, brachiopods, and bivalves) were affected by sudden truncations precisely at the iridium anomaly that marks the boundary. The paleontological record thus bears witness to terminal-Cretaceous extinctions on two time scales: a slow decline unrelated to the impact and a sharp truncation synchronous with and probably caused by the impact.

Predicting Glucose Sensor Behavior in Blood Using Transport Modeling: Relative Impacts of Protein Biofouling and Cellular Metabolic Effects

PubMed Central

Novak, Matthew T.; Yuan, Fan; Reichert, William M.

2013-01-01

Background Tissue response to indwelling glucose sensors remains a confounding barrier to clinical application. While the effects of fully formed capsular tissue on sensor response have been studied, little has been done to understand how tissue interactions occurring before capsule formation hinder sensor performance. Upon insertion in subcutaneous tissue, the sensor is initially exposed to blood, blood borne constituents, and interstitial fluid. Using human whole blood as a simple ex vivo experimental system, the effects of protein accumulation at the sensor surface (biofouling effects) and cellular consumption of glucose in both the biofouling layer and in the bulk (metabolic effects) on sensor response were assessed. Methods Medtronic MiniMed SofSensor glucose sensors were incubated in whole blood, plasma-diluted whole blood, and cell-free platelet-poor plasma (PPP) to analyze the impact of different blood constituents on sensor function. Experimental conditions were then simulated using MATLAB to predict the relative impacts of biofouling and metabolic effects on the observed sensor responses. Results Protein biofouling in PPP in both the experiments and the simulations was found to have no interfering effect upon sensor response. Experimental results obtained with whole and dilute blood showed that the sensor response was markedly affected by blood borne glucose-consuming cells accumulated in the biofouling layer and in the surrounding bulk. Conclusions The physical barrier to glucose transport presented by protein biofouling does not hinder glucose movement to the sensor surface, and the consumption of glucose by inflammatory cells, and not erythrocytes, proximal to the sensor surface has a substantial effect on sensor response and may be the main culprit for anomalous sensor behavior immediately following implantation. PMID:24351181

2011 spring drought in France : Evaluation of the SURFEX land surface model.

NASA Astrophysics Data System (ADS)

Lafont, S.; Barbu, A.; Szczypta, C.; Carrer, D.; Delire, C.; Calvet, J.-C.

2012-04-01

The spring of the year 2011 has been exceptionally dry in Western Europe. Over France, May 2011 has been one of the driest over the last 50 years. This event had a marked impact on vegetation development leading to very low value of the Leaf Area Index (LAI) during the growing season . In contrast, July 2011 has been in general wet and cold allowing a new vegetation development. This extreme event, followed by higher than normal rainfall is an excellent case-study to evaluate the capacity of a land surface model to simulate the drought impact on vegetation, and vegetation recovery after a drought. In this study, we used the SURFEX land surface model, in its ISBA-CC (CC stands for Carbon Cycle) configuration. The ISBA-CC version simulates the vegetation carbon cycle, interactive LAI and the carbon accumulation in wood and in the soil organic matter. This model is used by the GEOLAND2 Land Carbon Core Information Service. We performed 20-years simulations of SURFEX at high resolution (8 km) with atmospheric forcing from the SAFRAN dataset, an operational product over France. The vegetation map is provided by the ECOCLIMAP2 database. Following previous work that have confirmed a good simulation of the LAI inter-annual variability, this study investigates the ability of the model of reproducing the observed anomalies of LAI in 2011, in terms of timing and spatial patterns. We compare the simulated LAI with long time series (10 yr) of LAI derived from Earth Observation product within GEOLAND2 BIOPAR project. We quantify the anomalies of energy, water and carbon fluxes. We investigate the robustness of these results and the impact of modifying several important sub-modules of the model: soil texture, photosynthesis, and rainfall interception.

Probing the nanoscale with high-speed interferometry of an impacting drop

NASA Astrophysics Data System (ADS)

Thoroddsen, S. T.; Li, E. Q.; Vakarelski, I. U.; Langley, K.

2017-02-01

The simple phenomenon of a water drop falling onto a glass plate may seem like a trivial fluid mechanics problem. However, detailed imaging has shown that this process is highly complex and a small air-bubble is always entrapped under the drop when it makes contact with the solid. This bubble can interfere with the uniformity of spray coatings and degrade inkjet fabrication of displays etc. We will describe how we use high-speed interferometry at 5 million frames per second to understand the details of this process. As the impacting drop approaches the solid, the dynamics are characterized by a balance between the lubrication pressure in the thin air layer and the inertia of the bot-tom of the drop. This deforms the drop, forming a dimple at its bottom and making the drop touch the surface along a ring, thereby entrapping the air-layer, which is typically 1-3 μm thick. This air-layer can be highly compressed and the deceleration of the bottom of the drop can be as large as 300,000 g. We describe how the thickness evolution of the lubricating air-layer is extracted from following the interference fringes between frames. Two-color interferometry is also used to extract absolute layer thicknesses. Finally, we identify the effects of nanometric surface roughness on the first contact of the drop with the substrate. Here we need to resolve the 100 nm thickness changes occurring during 200 ns intervals, requiring these state of the art high-speed cameras. Surprisingly, we see a ring of micro-bubbles marking the first contact of the drop with the glass, only for microscope slides, which have a typical roughness of 20 nm, while such rings are absent for drop impacts onto molecularly smooth mica surfaces.

Abundance, stock origin, and length of marked and unmarked juvenile Chinook salmon in the surface waters of greater Puget Sound

USGS Publications Warehouse

Rice, C.A.; Greene, C.M.; Moran, P.; Teel, D.J.; Kuligowski, D.R.; Reisenbichler, R.R.; Beamer, E.M.; Karr, J.R.; Fresh, K.L.

2011-01-01

This study focuses on the use by juvenile Chinook salmon Oncorhynchus tshawytscha of the rarely studied neritic environment (surface waters overlaying the sublittoral zone) in greater Puget Sound. Juvenile Chinook salmon inhabit the sound from their late estuarine residence and early marine transition to their first year at sea. We measured the density, origin, and size of marked (known hatchery) and unmarked (majority naturally spawned) juveniles by means of monthly surface trawls at six river mouth estuaries in Puget Sound and the areas in between. Juvenile Chinook salmon were present in all months sampled (April-November). Unmarked fish in the northern portion of the study area showed broader seasonal distributions of density than did either marked fish in all areas or unmarked fish in the central and southern portions of the sound. Despite these temporal differences, the densities of marked fish appeared to drive most of the total density estimates across space and time. Genetic analysis and coded wire tag data provided us with documented individuals from at least 16 source populations and indicated that movement patterns and apparent residence time were, in part, a function of natal location and time passed since the release of these fish from hatcheries. Unmarked fish tended to be smaller than marked fish and had broader length frequency distributions. The lengths of unmarked fish were negatively related to the density of both marked and unmarked Chinook salmon, but those of marked fish were not. These results indicate more extensive use of estuarine environments by wild than by hatchery juvenile Chinook salmon as well as differential use (e.g., rearing and migration) of various geographic regions of greater Puget Sound by juvenile Chinook salmon in general. In addition, the results for hatchery-generated timing, density, and length differences have implications for the biological interactions between hatchery and wild fish throughout Puget Sound. ?? American Fisheries Society 2011.

Comparing population size estimators for plethodontid salamanders

USGS Publications Warehouse

Bailey, L.L.; Simons, T.R.; Pollock, K.H.

2004-01-01

Despite concern over amphibian declines, few studies estimate absolute abundances because of logistic and economic constraints and previously poor estimator performance. Two estimation approaches recommended for amphibian studies are mark-recapture and depletion (or removal) sampling. We compared abundance estimation via various mark-recapture and depletion methods, using data from a three-year study of terrestrial salamanders in Great Smoky Mountains National Park. Our results indicate that short-term closed-population, robust design, and depletion methods estimate surface population of salamanders (i.e., those near the surface and available for capture during a given sampling occasion). In longer duration studies, temporary emigration violates assumptions of both open- and closed-population mark-recapture estimation models. However, if the temporary emigration is completely random, these models should yield unbiased estimates of the total population (superpopulation) of salamanders in the sampled area. We recommend using Pollock's robust design in mark-recapture studies because of its flexibility to incorporate variation in capture probabilities and to estimate temporary emigration probabilities.

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

23 CFR 924.11 - Implementation.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., where applicable, for highway construction projects, 23 CFR part 172 for engineering and design services..., pavement markings, or installation of traffic signs, traffic lights, guardrails, impact attenuators... may amount up to 100 percent for projects for signing, pavement markings, active warning devices, and...

Additive manufactured serialization

DOEpatents

Bobbitt, III, John T.

2017-04-18

Methods for forming an identifying mark in a structure are described. The method is used in conjunction with an additive manufacturing method and includes the alteration of a process parameter during the manufacturing process. The method can form in a unique identifying mark within or on the surface of a structure that is virtually impossible to be replicated. Methods can provide a high level of confidence that the identifying mark will remain unaltered on the formed structure.

16 CFR § 1505.7 - Maximum acceptable surface temperatures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (as described—in § 1505.6 (g)(2)) Thermal inertia type 1 Temperatures °C. °F. A 1 50 122 A 2 55 131 A... 60 140 D marked 2 75 167 D marked 3 100 212 D marked 4 125 257 E (2)   (3)   (3) 1 Thermal inertia... inertia of a material can be obtained by multiplying the thermal conductivity (cal./cm./sec./degrees C...

An 8.5 m long ammonite drag mark from the Upper Jurassic Solnhofen Lithographic Limestones, Germany

PubMed Central

Falkingham, Peter L.; Schweigert, Günter; Jiménez, Alejandro P.

2017-01-01

Trackways and tracemakers preserved together in the fossil record are rare. However, the co-occurrence of a drag mark, together with the dead animal that produced it, is exceptional. Here, we describe an 8.5 m long ammonite drag mark complete with the preserved ammonite shell (Subplanites rueppellianus) at its end. Previously recorded examples preserve ammonites with drag marks of < 1 m. The specimen was recovered from a quarry near Solnhofen, southern Germany. The drag mark consists of continuous parallel ridges and furrows produced by the ribs of the ammonite shell as it drifted just above the sediment surface, and does not reflect behaviour of the living animal. PMID:28489915

Pre-polishing on a CNC platform with bound abrasive contour tools

NASA Astrophysics Data System (ADS)

Schoeffer, Adrienne E.

2003-05-01

Deterministic micorgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-51.tm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an OptiproTM CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Prepolishing on a CNC platform with bound abrasive contour tools

NASA Astrophysics Data System (ADS)

Schoeffler, Adrienne E.; Gregg, Leslie L.; Schoen, John M.; Fess, Edward M.; Hakiel, Michael; Jacobs, Stephen D.

2003-05-01

Deterministic microgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-5μm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an Optipro CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

Flood Map for the Winooski River in Waterbury, Vermont, 2014

USGS Publications Warehouse

Olson, Scott A.

2015-01-01

High-water marks from Tropical Storm Irene were available for seven locations along the study reach. The highwater marks were used to estimate water-surface profiles and discharges resulting from Tropical Storm Irene throughout the study reach. From a comparison of the estimated water-surface profile for Tropical Storm Irene with the water-surface profiles for the 1- and 0.2-percent annual exceedance probability (AEP) floods, it was determined that the high-water elevations resulting from Tropical Storm Irene exceeded the estimated 1-percent AEP flood throughout the Winooski River study reach but did not exceed the estimated 0.2-percent AEP flood at any location within the study reach.

The Impact of Pro-Government Militias on State and Human Security: A Comparative Analysis of the Afghan Local Police and the Janjaweed

DTIC Science & Technology

2018-03-01

GOVERNMENT MILITIAS ON STATE AND HUMAN SECURITY: A COMPARATIVE ANALYSIS OF THE AFGHAN LOCAL POLICE AND THE JANJAWEED by Mark D. Phelps March...MILITIAS ON STATE AND HUMAN SECURITY: A COMPARATIVE ANALYSIS OF THE AFGHAN LOCAL POLICE AND THE JANJAWEED 5. FUNDING NUMBERS 6. AUTHOR(S) Mark D...human security. This thesis examines the relationship and impact of pro-government militias on state and human security by conducting a comparative

Surface expression of the Chicxulub crater

PubMed

Pope, K O; Ocampo, A C; Kinsland, G L; Smith, R

1996-06-01

Analyses of geomorphic, soil, and topographic data from the northern Yucatan Peninsula, Mexico, confirm that the buried Chicxulub impact crater has a distinct surface expression and that carbonate sedimentation throughout the Cenozoic has been influenced by the crater. Late Tertiary sedimentation was mostly restricted to the region within the buried crater, and a semicircular moat existed until at least Pliocene time. The topographic expression of the crater is a series of features concentric with the crater. The most prominent is an approximately 83-km-radius trough or moat containing sinkholes (the Cenote ring). Early Tertiary surfaces rise abruptly outside the moat and form a stepped topography with an outer trough and ridge crest at radii of approximately 103 and approximately 129 km, respectively. Two discontinuous troughs lie within the moat at radii of approximately 41 and approximately 62 km. The low ridge between the inner troughs corresponds to the buried peak ring. The moat corresponds to the outer edge of the crater floor demarcated by a major ring fault. The outer trough and the approximately 62-km-radius inner trough also mark buried ring faults. The ridge crest corresponds to the topographic rim of the crater as modified by postimpact processes. These interpretations support previous findings that the principal impact basin has a diameter of approximately 180 km, but concentric, low-relief slumping extends well beyond this diameter and the eroded crater rim may extend to a diameter of approximately 260 km.

Tracking illegal small arms traffic across U.S. borders through the implementation of firearm microstamping to small arms and small arms exports

NASA Astrophysics Data System (ADS)

Lizotte, Todd E.; Ohar, Orest P.

2009-05-01

At a border security conference in August 2008, Michael Sullivan, acting director of Bureau of Alcohol, Tobacco, Firearms and Explosives stated that, "Nearly all illegal firearms (90% to 95%) seized in Mexico come from the United States"[1]. When firearms are recovered at a crime scene, the firearms can be traced providing specific details on illegal firearm dealers or straw purchasers within the United States. Criminals or narco terrorist groups target US dealers to source firearms for drug cartels in Mexico and South America. Joint law enforcement programs between the US and Mexico law enforcement have been effective, however, in most cases the firearms that are seized are only a small fraction of the firearms trafficked across the United States border. A technology called Microstamping, when applied to newly manufactured firearms will provide further opportunities for tracing illegal firearms for law enforcement in the United States and across the globe. Microstamping is a patented technology and trace solution where intentional tooling marks are formed or micromachined onto firearms interior surfaces that come into contact or impact the surfaces of cartridge casings. The intentional tooling marks can take the form of alphanumeric codes or encoded geometric codes, such as a barcode. As the firearm is discharged the intentional tooling marks transfer a code to the cartridge casing before it is ejected out of the firearm. When recovered at the scene of an incident, the Microstamped cartridge can indentify a specific firearm, without the need to recover that firearm. Microstamping provides critical intelligence for use in border security operations and cross border violent drug related crime investigations. This paper will explain the key attributes of microstamping technology; including its potential benefits in border security operations and how data gathered from the technique can be used in geospatial information systems to identify illicit firearm sources, trafficking routes, as well as spatial and temporal mapping of narco-terrorist movements on either side of the border.

Laser micro-etching of metal prostheses for personal identification

PubMed Central

Ganapathy, Dhanraj; Sivaswamy, Vinay; Sekhar, Prathap

2017-01-01

Denture marking techniques play a vital role in establishing personal identification in suitable clinical and forensic situations. The denture marking techniques are categorized broadly into additive and ablative methods. Additive methods involve embedding or impregnation of markers for establishing personal identity. Ablative methods involve partial removal of the denture surface thereby providing a marking for identification. Engraving and etching methods are the commonly used ablative methods. Ablative methods can be of contact and noncontact subtypes. Laser micro-etching is a precise noncontact ablative denture marking technique that could be used for prostheses-guided personal identification. PMID:28584473

Laser micro-etching of metal prostheses for personal identification.

PubMed

Ganapathy, Dhanraj; Sivaswamy, Vinay; Sekhar, Prathap

2017-01-01

Denture marking techniques play a vital role in establishing personal identification in suitable clinical and forensic situations. The denture marking techniques are categorized broadly into additive and ablative methods. Additive methods involve embedding or impregnation of markers for establishing personal identity. Ablative methods involve partial removal of the denture surface thereby providing a marking for identification. Engraving and etching methods are the commonly used ablative methods. Ablative methods can be of contact and noncontact subtypes. Laser micro-etching is a precise noncontact ablative denture marking technique that could be used for prostheses-guided personal identification.

Mars exploration rover geologic traverse by the spirit rover in the plains of Gusev crater, Mars

USGS Publications Warehouse

Crumpler, L.S.; Squyres, S. W.; Arvidson, R. E.; Bell, J.F.; Blaney, D.; Cabrol, N.A.; Christensen, P.R.; DesMarais, D.J.; Farmer, J.D.; Fergason, R.; Golombek, M.P.; Grant, F.D.; Grant, J. A.; Greeley, R.; Hahn, B.; Herkenhoff, K. E.; Hurowitz, J.A.; Knudson, A.T.; Landis, G.A.; Li, R.; Maki, J.; McSween, H.Y.; Ming, D. W.; Moersch, J.E.; Payne, M.C.; Rice, J.W.; Richter, L.; Ruff, S.W.; Sims, M.; Thompson, S.D.; Tosca, N.; Wang, A.; Whelley, P.; Wright, S.P.; Wyatt, M.B.

2005-01-01

The Spirit rover completed a 2.5 km traverse across gently sloping plains on the floor of Gusev crater from its location on the outer rim of Bonneville crater to the lower slopes of the Columbia Hills, Mars. Using the Athena suite of instruments in a transect approach, a systematic series of overlapping panoramic mosaics, remote sensing observations, surface analyses, and trenching operations documented the lateral variations in landforms, geologic materials, and chemistry of the surface throughout the traverse, demonstrating the ability to apply the techniques of field geology by remote rover operations. Textures and shapes of rocks within the plains are consistent with derivation from impact excavation and mixing of the upper few meters of basaltic lavas. The contact between surrounding plains and crater ejecta is generally abrupt and marked by increases in clast abundance and decimeter-scale steps in relief. Basaltic materials of the plains overlie less indurated and more altered rock types at a time-stratigraphic contact between the plains and Columbia Hills that occurs over a distance of one to two meters. This implies that regional geologic contacts are well preserved and that Earth-like field geologic mapping will be possible on Mars despite eons of overturn by small impacts. ?? 2005 Geological Society of America.

A review of the clinical implications of anti-infective biomaterials and infection-resistant surfaces.

PubMed

Campoccia, Davide; Montanaro, Lucio; Arciola, Carla Renata

2013-11-01

Infection is currently regarded as the most severe and devastating complication associated to the use of biomaterials. The important social, clinical and economic impacts of implant-related infections are promoting the efforts to obviate these severe diseases. In this context, the development of anti-infective biomaterials and of infection-resistant surfaces is being regarded as the main strategy to prevent the establishment of implant colonisation and biofilm formation by bacteria. In this review, the attention is focused on the biomaterial-associated infections, from which the need for anti-infective biomaterials originates. Biomaterial-associated infections differ markedly for epidemiology, aetiology and severity, depending mainly on the anatomic site, on the time of biomaterial application, and on the depth of the tissues harbouring the prosthesis. Here, the diversity and complexity of the different scenarios where medical devices are currently utilised are explored, providing an overview of the emblematic applicative fields and of the requirements for anti-infective biomaterials. © 2013 Elsevier Ltd. All rights reserved.

Wildfires and animal extinctions at the Cretaceous/Tertiary boundary

NASA Astrophysics Data System (ADS)

Adair, Robert K.

2010-06-01

Persuasive models of the ejection of material at high velocities from the Chicxulub asteroid impact marking the Cretaceous/Tertiary boundary have led to the conclusion that upon return, that material, heated in passage through the upper atmosphere, generated a high level of infrared energy density over the Earth's surface. That radiant energy has been considered to be a direct source of universal wildfires, which were presumed to be a major cause of plant and animal species extinctions. The extinction of many animal species, especially the dinosaurs, has also been attributed to the immediate lethal effects of the radiation. I find that the absorption of the radiation by the atmosphere, by cloud formations, and by ejecta drifting in the lower atmosphere reduced the radiation at the surface to a level that cannot be expected to have generated universal fires. Although the reduced radiation will have likely caused severe injuries to many animals, such insults alone seem unlikely to have generated the overall species extinctions that have been deduced.

Morphological Deficits of Children with SLI: Evaluation of Number Marking and Agreement.

ERIC Educational Resources Information Center

Rice, Mabel L.; Oetting, Janna B.

1993-01-01

Grammatical deficits (e.g., missing feature, surface account, and missing agreement) reported for children with specific language impairment (SLI) were evaluated in spontaneous language transcripts from 108 preschool children. Results indicated that children with SLI do control number marking but find number agreement across clausal boundaries…

DebriSat Pre Preshot Laboratory Analyses

DTIC Science & Technology

2015-03-27

plate on up range side. MLI Down range Up range SBU Marking Witness Plates: Post Test (protected) 17 Surfaces of samples under Whipple plates are...s SBU Marking Witness Plates Post Test : Whipple Plates 59 Bottom Middle Top Up range is to the right – note sharp band of deposits on up range side...Marking Hold down plates: Post test 63 Up range Note larger deposit fragments on the down range plate. Similar larger deposits were observed on

Formation of bulk refractive index structures

DOEpatents

Potter, Jr., Barrett George; Potter, Kelly Simmons; Wheeler, David R.; Jamison, Gregory M.

2003-07-15

A method of making a stacked three-dimensional refractive index structure in photosensitive materials using photo-patterning where first determined is the wavelength at which a photosensitive material film exhibits a change in refractive index upon exposure to optical radiation, a portion of the surfaces of the photosensitive material film is optically irradiated, the film is marked to produce a registry mark. Multiple films are produced and aligned using the registry marks to form a stacked three-dimensional refractive index structure.

Laser-Marking Mechanism of Thermoplastic Polyurethane/Bi2O3 Composites.

PubMed

Zhong, Wei; Cao, Zheng; Qiu, Pengfei; Wu, Dun; Liu, Chunlin; Li, Huili; Zhu, He

2015-11-04

Using bismuth oxide (Bi2O3) as a laser-marking additive and thermoplastic polyurethane (TPU) as the matrix, TPU/Bi2O3 composite materials were prepared by melt blending in a torque rheometer. The sheet samples prepared from the TPU/Bi2O3 composites were treated in air by scanning with a neodymium-doped yttrium aluminum garnet (Nd: YAG) pulsed laser beam at a wavelength of 1064 nm. Compared with the pure TPU sample, the laser-marked composite samples exhibited differences in marking contrast as the Bi2O3 content increased from 0.1% to 1.0% based on stereomicroscope analysis. Scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, thermogravimetry analysis, and X-ray diffraction were used to characterize the laser-marked surface material of the composite samples. Furthermore, a mechanism for the laser-effected darkening of the TPU/Bi2O3 composites was proposed. The results herein indicated that the addition of the Bi2O3 laser-sensitive additive to TPU resulted in laser darkening of the TPU/Bi2O3 composites. The marking contrast and visual appearance of the surface of the TPU/Bi2O3 composites after laser irradiation was due to a synergistic effect consisting of carbonization via TPU pyrolysis and reduction of Bi2O3 to black bismuth metal.

Measuring the Impact of Rising CO2 and CH4 on the Surface Energy Balance

NASA Astrophysics Data System (ADS)

Feldman, D.; Collins, W.; Biraud, S.; Turner, D. D.; Mlawer, E. J.; Gero, P. J.; Xie, S.; Shippert, T.; Torn, M. S.

2015-12-01

We use observations at the North Slope of Alaska (NSA) and Southern Great Plains (SGP) ARM sites to improve understanding both of the distribution of CO2 and CH4and their influence on the surface energy balance. We use aircraft and ground-based in situ data to characterize the temporal distribution of these greenhouse gases, and spectroscopic observations to derive their collocated surface radiative forcing. The spectroscopically-measured surface radiative forcing from rising CO2 is 0.2 W/m2/decade at both sites, with a seasonal cycle of 0.2 W/m2. This finding is largely consistent with theoretical predictions, providing robust evidence of radiative perturbations to the Earth's surface energy budget due to anthropogenic influences. The contribution from CH4 to the surface energy balance is more spatially and temporally heterogeneous. The ground-based measurements of CH4 at NSA and SGP indicate rising atmospheric concentrations except for a hiatus from 1995-2005, while more recent aircraft profiles indicate that concentrations in the boundary layer and free troposphere are correlated at NSA and decorrelated at SGP. The probability density functions of boundary layer concentrations of CH4 at NSA show little skew, but at SGP show positive skewness, which increased with the introduction of nearby fossil-fuel extraction. The correlated increases in atmospheric measurements of C2H6 and CH4that only occur at SGP are consistent with an anthropogenic influence there. Time-series of spectroscopically-measured CH4 surface radiative forcing at SGP and NSA also indicate positive trends of 0.1 W/m2/decade associated with the end of the hiatus, marked seasonal cycles, and little skew at NSA and a positive skew at SGP. The combination of in situ and spectroscopic measurements at these sites enables the quantification of surface radiative forcing from anthropogenic CH4. Implications are discussed for how advanced spectroscopic remote sensing measurements of CH4 can be used to quantify the impact of fossil fuel extraction on surface energy budget.

A comparison of multi-metal deposition processes utilising gold nanoparticles and an evaluation of their application to 'low yield' surfaces for finger mark development.

PubMed

Fairley, C; Bleay, S M; Sears, V G; NicDaeid, N

2012-04-10

This paper reports a comparison of the effectiveness and practicality of using different multi-metal deposition processes for finger mark development. The work investigates whether modifications can be made to improve the performance of the existing process published by Schnetz. Secondly, we compare the ability of different multi-metal deposition processes to develop finger marks on a range of surfaces with that of other currently used development processes. All published multi-metal deposition processes utilise an initial stage of colloidal gold deposition followed by enhancement of the marks with using a physical developer. All possible combinations of colloidal gold and physical developer stages were tested. The method proposed by Schnetz was shown to be the most effective process, however a modification which reduced the pH of the enhancement solution was revealed to provide the best combination of effectiveness and practicality. In trials comparing the modified formulation with vacuum metal deposition, superglue and powder suspensions on surfaces which typically give low finger mark yields (cling film, plasticised vinyl, leather and masking tape), the modified method produced significantly better results over existing processes for cling film and plasticised vinyl. The modified formulation was found to be ineffective on both masking tape and leather. It is recommended that further tests be carried out on the modified multi-metal deposition formulation to establish whether it could be introduced for operational work on cling film material in particular. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

A comparative study on the effects of barite, ilmenite and bentonite on four suspension feeding bivalves.

PubMed

Strachan, Maia F; Kingston, Paul F

2012-10-01

The impact of drilling mud components on the filtration activity and survival of bivalve molluscs was investigated by exposing them to suspensions of 'standard' barite, finely milled barite, ilmenite and bentonite in sea water. Introduction of the components stimulated filtration activity in all four bivalves. In addition, the introduction of standard barite and ilmenite both had lethal effects, with none of the bivalves surviving the full duration of the experiments. In-vivo observations of the gill surfaces provided direct evidence of physical damage caused by the administration of barite and ilmenite. A marked difference between filtration activity and survival of animals dosed with 'standard' barite and 'fine' barite suggests that the observed effects were primarily caused by physical interference with gill function. The results also suggest that the use of fine barite in offshore drilling may provide a more favourable environmental impact profile than the use of ilmenite. Copyright © 2012. Published by Elsevier Ltd.

UAV-based mapping, back analysis and trajectory modeling of a coseismic rockfall in Lefkada island, Greece

NASA Astrophysics Data System (ADS)

Saroglou, Charalampos; Asteriou, Pavlos; Zekkos, Dimitrios; Tsiambaos, George; Clark, Marin; Manousakis, John

2018-01-01

We present field evidence and a kinematic study of a rock block mobilized in the Ponti area by a Mw = 6.5 earthquake near the island of Lefkada on 17 November 2015. A detailed survey was conducted using an unmanned aerial vehicle (UAV) with an ultrahigh definition (UHD) camera, which produced a high-resolution orthophoto and a digital terrain model (DTM). The sequence of impact marks from the rock trajectory on the ground surface was identified from the orthophoto and field verified. Earthquake characteristics were used to estimate the acceleration of the rock slope and the initial condition of the detached block. Using the impact points from the measured rockfall trajectory, an analytical reconstruction of the trajectory was undertaken, which led to insights on the coefficients of restitution (CORs). The measured trajectory was compared with modeled rockfall trajectories using recommended parameters. However, the actual trajectory could not be accurately predicted, revealing limitations of existing rockfall analysis software used in engineering practice.

Layered/Pancake-like Ejecta on Ceres: Inferring the Composition and Mechanical Properties of the Cerean Surface through Modeling of Ejecta Emplacement

NASA Astrophysics Data System (ADS)

Hughson, K.; Russell, C. T.; Schmidt, B. E.; Chilton, H.; Scully, J. E. C.; Sizemore, H. G.; Byrne, S.; Platz, T.; Raymond, C. A.

2017-12-01

During the Survey, High Altitude Mapping Orbit, and Low Altitude Mapping Orbit phases of the primary mission Dawn's Framing Camera observed a multitude of globally distributed lobate deposits. These flows were broadly interpreted as either similar to ice-cored/ice-cemented flows (Type 1 flows) on Earth and Mars, long run-out terrestrial or martian landslides (Type 2 flows), or highly mobile fluidized ejecta-like deposits (Type 3 flows) (Buczckowski et al., 2016; Schmidt et al., 2017). The Type 3 flows are morphologically similar to layered/pancake ejecta found on Mars and Ganymede where they are thought to be caused by impacts into ground ice rich substrates (Mouginis-Mark, 1979; Boyce et al., 2010). We assess the effects of target material strength, sliding friction, and vapor entrainment on the production of these features by comparing the ejecta mobility (EM: the ratio of the radius of the ejecta blanket to the radius of the parent crater) values for all Type 3 cerean flows to a ballistic/kinematic sliding model similar to the one developed by Weiss et al. (2014) to model EM for impacts into a variety of ground ice rich substrates of differing volatile content on Mars. Initial results suggest that, in order for these features to form, the cerean surface requires a large coefficient of sliding friction (>0.1), and that significant amounts of water be vaporized during impact. However, the model does not tightly constrain the strength of the target material (best-fit values range from granite-like to unconsolidated-sand-like). These results are consistent with a largely dry, rough, and thin surface layer underlain by material rich in pore-filling ground ice, even at low latitudes. Additionally, before the Fall Meeting we will attempt to constrain the thickness of the ice-poor surface layer. This will be done through a combined analysis of model results and morphometric parameters of individual Type 3 flows. Future implementation of this model will further incorporate compositional and geophysical knowledge attained from Dawn in order to better constrain the strength of the cerean surface.

Enamel-based mark performance for marking Chinese mystery snail Bellamya chinensis

USGS Publications Warehouse

Wong, Alec; Allen, Craig R.; Hart, Noelle M.; Haak, Danielle M.; Pope, Kevin L.; Smeenk, Nicholas A.; Stephen, Bruce J.; Uden, Daniel R.

2013-01-01

The exoskeleton of gastropods provides a convenient surface for carrying marks, and i the interest of improving future marking methods our laboratory assessed the performance of an enamel paint. The endurance of the paint was also compared to other marking methods assessed in the past. We marked the shells of 30 adult Chinese mystery snails Bellamya chinensis and held them in an aquarium for 181 days. We observed no complete degradation of any enamel-paint mark during the 181 days. The enamel-paint mark was superior to a nai;-polish mark, which lasted a median of 100 days. Enamel-paint marks also have a lower rate of loss (0.00 month-1 181 days) than plastic bee tags (0.01 month-1, 57 days), gouache paint (0.07 month-1, 18.5 days), or car body paint from studies found in scientific literature. Legibility of enamel-paint marks had a median lifetime of 102 days. The use of enamel paint on the shells of gastropods is a viable option for studies lasting up to 6 months. Furthermore, visits to capture-mark-recapture site 1 year after application of enamel-paint marks on B. chinesnis shells produced several individuals on which the enamel paint was still visible, although further testing is required to clarify durability over longer periods.

The Effect of Language Learning Strategies on Proficiency, Attitudes and School Achievement

PubMed Central

Habók, Anita; Magyar, Andrea

2018-01-01

This study examines language learning strategy (LLS) use in connexion with foreign language attitude, proficiency and general school achievement among lower secondary students in Years 5 and 8 (n = 868) in Hungary. An adapted version of the Strategies Inventory for Language Learning questionnaire was used for data collection. The results showed that Hungarian students mainly engage in metacognitive strategies in both years. Differences between more and less proficient language learners’ strategy use have also been found. With regard to the effect of LLS on foreign language attitude, the foreign language mark and school achievement, path analysis indicated a good fit in both years. The metacognitive, social and memory strategies primarily influenced foreign language attitudes and marks in Year 5. The metacognitive strategies had a slight impact on school achievement as well as on foreign language marks. We demonstrated the dominant effect of metacognitive strategies and the low effect of memory strategies in Year 8. In addition, metacognitive strategies also influenced foreign language marks. The effect of foreign language marks on school achievement was also remarkable. There was a strong impact on the children’s attitudes through these variables. PMID:29379461

Multi Response Optimization of Laser Micro Marking Process:A Grey- Fuzzy Approach

NASA Astrophysics Data System (ADS)

Shivakoti, I.; Das, P. P.; Kibria, G.; Pradhan, B. B.; Mustafa, Z.; Ghadai, R. K.

2017-07-01

The selection of optimal parametric combination for efficient machining has always become a challenging issue for the manufacturing researcher. The optimal parametric combination always provides a better machining which improves the productivity, product quality and subsequently reduces the production cost and time. The paper presents the hybrid approach of Grey relational analysis and Fuzzy logic to obtain the optimal parametric combination for better laser beam micro marking on the Gallium Nitride (GaN) work material. The response surface methodology has been implemented for design of experiment considering three parameters with their five levels. The parameter such as current, frequency and scanning speed has been considered and the mark width, mark depth and mark intensity has been considered as the process response.

Multitemporal satellite data analyses for archaeological mark detection: preliminary results in Italy and Argentina

NASA Astrophysics Data System (ADS)

Lasaponara, Rosa; Masini, Nicola

2014-05-01

The current availability of very high resolution satellite data provides an excellent tool to detect and monitor archaeological marks, namely spectral and spatial anomalies linked to the presence of buried archaeological remains from a landscape view down to local scale (single site) investigations. Since the end of the nineteenth century, aerial photography has been the remote sensing tool most widely used in archaeology for surveying both surface and sub-surface archaeological remains. Aerial photography was a real "revolution" in archaeology being an excellent tool for investigations addressed at detecting underground archaeological structures through the reconnaissance of the so-called "archaeological marks" generally grouped and named as "soil","crop marks" "snow marks", and also recently "weed marks" (Lasaponara and Masini). Such marks are generally visible only from an aerial view (see detail in Lasaponara and Masini 2009, Ciminale et al. 2009, Masini and Lasaponara 2006 Lasaponara et al 2011) . In particular, soil marks are changes in soil colour or texture due to the presence of surface and shallow remains. Crop marks are changes in crop texture linked to as differences in height or colour of crops which are under stress due to lack of water or deficiencies in other nutrients caused by the presence of masonry structures in the subsoil. Crop marks can also be formed above damp and nutritious soil of buried pits and ditches. Such marks are generally visible only from an aerial view, especially during the spring season. In the context of the Project "Remote sensing technologies applied to the management of natural and cultural heritage in sites located in Italy and Argentina: from risk monitoring to mitigatin startegies P@an_sat", funded by the Italian Ministry of Foreign Affair, we tested the capability of multitemporal data, from active and passive satellite sensors, in the detection of "archaeological marks". The areas of interested were selected from within Basilicata and Puglia Region, southern Patagonia and Payunia-Campo Volcanicos Liancanelo e PayunMatru respectively, in Italy and Argentina. We focused our attention on diverse surfaces and soil types in different periods of the year in order to assess the capabilities of both optical and radar data to detect archaeological marks in different ecosystems and seasons. We investigated not only crop culture during the "favourable vegetative period" to enhance the presence of subsurface remains but also the "spectral response" of spontaneous, sparse herbaceous covers during periods considered and expected to be less favourable (as for example summer and winter) for this type of investigation. The main interesting results were the capability of radar (cosmoskymed) and multispectral optical data satellite data (Pleiades, Quickbird, Geoeye) to highlight the presence of structures below the surface even (i) in during period of years generally considered not "suitable for crop mark investigations" and even (ii) in areas only covered by sparse, spontaneous herbaceous plants in several test sites investigate din both Argentine and Italian areas of interest. Preliminary results conducted in both Italian and Argentina sites pointed out that Earth Observation (EO) technology can be successfully used for extracting useful information on traces the past human activities still fossilized in the modern landscape in different ecosystems and seasons. Moreover the multitemporal analyses of satellite data can fruitfully applied to: (i) improve knowledge, (ii) support monitoring of natural and cultural site, (iii) assess natural and man-made risks including emerging threats to the heritage sites. References Lasaponara R, N Masini 2009 Full-waveform Airborne Laser Scanning for the detection of medieval archaeological microtopographic relief Journal of Cultural Heritage 10, e78-e82 Ciminale M, D Gallo, R Lasaponara, N Masini 2009 A multiscale approach for reconstructing archaeological landscapes: applications in Northern Apulia (Italy) Archaeological Prospection 16 (3), 143-153 Masini N, R Lasaponara 2006 Satellite-based recognition of landscape archaeological features related to ancient human transformation Journal of Geophysics and Engineering 3 (3), 230 Lasaponara R, N Masini, E Rizzo, G Orefici 2011 New discoveries in the Piramide Naranjada in Cahuachi (Peru) using satellite, Ground Probing Radar and magnetic investigations Journal of Archaeological Science 38 (9), 2031-2039

Road marking features extraction using the VIAPIX® system

NASA Astrophysics Data System (ADS)

Kaddah, W.; Ouerhani, Y.; Alfalou, A.; Desthieux, M.; Brosseau, C.; Gutierrez, C.

2016-07-01

Precise extraction of road marking features is a critical task for autonomous urban driving, augmented driver assistance, and robotics technologies. In this study, we consider an autonomous system allowing us lane detection for marked urban roads and analysis of their features. The task is to relate the georeferencing of road markings from images obtained using the VIAPIX® system. Based on inverse perspective mapping and color segmentation to detect all white objects existing on this road, the present algorithm enables us to examine these images automatically and rapidly and also to get information on road marks, their surface conditions, and their georeferencing. This algorithm allows detecting all road markings and identifying some of them by making use of a phase-only correlation filter (POF). We illustrate this algorithm and its robustness by applying it to a variety of relevant scenarios.

Squiggles in Hellas Planitia

NASA Image and Video Library

2017-10-25

At around 2,200 kilometers in diameter, Hellas Planitia is the largest visible impact basin in the Solar System, and hosts the lowest elevations on Mars' surface as well as a variety of landscapes. This image from NASA's Mars Reconnaisance Orbiter (MRO) covers a small central portion of the basin and shows a dune field with lots of dust devil trails. In the middle, we see what appears to be long and straight "scratch marks" running down the southeast (bottom-right) facing dune slopes. If we look closer, we can see these scratch marks actually squiggle back and forth on their way down the dune. These scratch marks are linear gullies. Just like on Earth, high-latitude regions on Mars are covered with frost in the winter. However, the winter frost on Mars is made of carbon dioxide ice (dry ice) instead of water ice. We believe linear gullies are the result of this dry ice breaking apart into blocks, which then slide or roll down warmer sandy slopes, sublimating and carving as they go. The linear gullies exhibit exceptional sinuosity (the squiggle pattern) and we believe this to be the result of repeated movement of dry ice blocks in the same path, possibly in combination with different hardness or flow resistance of the sand within the dune slopes. Determining the specific process that causes the formation and evolution of sinuosity in linear gullies is a question scientists are still trying to answer. What do you think causes the squiggles? https://photojournal.jpl.nasa.gov/catalog/PIA22052

Effect of hydrofluoric acid surface treatments on micro-shear bond strength of CAD/CAM ceramics

PubMed Central

Mokhtarpour, Faraneh; Alaghehmand, Homayoon; Khafri, Soraya

2017-01-01

Introduction Dental ceramics are appreciated as highly esthetic restorative materials that can simulate the appearance of natural dentition better than other materials. The aim of this study was to evaluate the effect of hydrofluoric acid concentration and etching time on micro-shear bond strength (μSBS) to IPS e.max CAD and Vita Mark II of a dual cured resin cement (Panavia F2.0). Methods This study was an experimental in vitro study, performed in the dental material research center of Babol University of Medical Sciences in 2016. Two hydrofluoric acid concentrations (5% and 10%) and three different etching times (20, 60 and 120 seconds) were used to etch the specimens respectively. A silane coupling agent (Clearfil porcelain activator) and priming and bonding agent (Clearfil SE bond) were used on the etched surfaces in accordance to the manufacturer’s instructions of use. Then resin cement was applied on the prepared ceramic surfaces and light cured. μSBS between resin cement and the porcelains were measured with a universal testing machine. Mode of failure was observed with 40× magnification by means of a Stereo microscope. Data were analyzed with ANOVA and independent-samples t-test and Chi-square tests. Results In both e.max and Vita Mark II groups, μSBS were not significantly different when different etching times (one-way ANOVA) and HF acid concentrations (Independent-samples t-test) were used (p>0.05), but the highest μSBS was shown in e.max specimens etched 60 s with 5% HF and Vita Mark II specimens etched 20 s with 10% HF. μSBS of e.max was significantly higher than Vita Mark II (p=0.00). Conclusion Best surface treatment for e.max and Vita Mark II ceramics is 20 s etch using 5 % hydrofluoric acid. PMID:29238488

Interaction between shallow groundwater, saline surface water and contaminant discharge at a seasonally and tidally forced estuarine boundary

NASA Astrophysics Data System (ADS)

Westbrook, S. J.; Rayner, J. L.; Davis, G. B.; Clement, T. P.; Bjerg, P. L.; Fisher, S. J.

2005-02-01

This paper presents findings from a 2-year field investigation of a dissolved hydrocarbon groundwater plume flowing towards a tidally and seasonally forced estuarine river system in Perth, Western Australia. Samples collected from transects of multiport wells along the riverbank and into the river, enabled mapping of the fine scale (0.5 m) vertical definition of the hydrocarbon plume and its longitudinal extent. Spear probing beneath the river sediments and water table, and transient monitoring of multiport wells (electrical conductivity) was also carried out to define the zone of mixing between river water and groundwater (the hyporheic zone) and its variability. The results showed that groundwater seepage into the estuarine surface sediments occurred in a zone less than 10 m from the high tide mark, and that this distance and the hyporheic transition zone were influenced by tidal fluctuations and infiltration of river water into the sediments. The dissolved BTEXN (benzene, toluene, ethylbenzene, the xylene isomers and naphthalene) distributions indicated the behaviour of the hydrocarbon plume at the groundwater/surface water transition zone to be strongly influenced by edge-focussed discharge. Monitoring programs and risk assessment studies at similar contaminated sites should therefore focus efforts within the intertidal zone where contaminants are likely to impact the surface water and shallow sediment environments.

Changes in urban-related precipitation in the summer over three city clusters in China

NASA Astrophysics Data System (ADS)

Zhao, Deming; Wu, Jian

2017-09-01

The impacts of urban surface expansion on the summer precipitations over three city clusters [Beijing-Tianjin-Hebei (BTH), the Yangtze River Delta (YRD), and the Pearl River Delta (PRD)] in eastern China under different monsoonal circulation backgrounds were explored using the nested fifth-generation Penn State/NCAR Mesoscale Model version 3.7 (MM5 V3.7), including the urban-related thermal and dynamical parameters. Ten-year integrations were performed using satellite image data from 2000 and 2010 to represent the urban surface distributions and expansions in China. Changes in the precipitation revealed obvious subregional characteristics, which could be explained by the influences of the vertical wind velocity and moisture flux. With urban-related warming, vertical wind motion generally intensified over urban surface-expanded areas. Meanwhile, the increase in impervious surface areas induced rapid rainwater runoff into drains, and the Bowen ratio increased over urban areas, which further contributed to changes in the local moisture fluxes in these regions. The intensities of the changes in precipitation were inconsistent over the three city clusters, although the changes in vertical motion and local evaporation were similar, which indicates that the changes in precipitation cannot be solely explained by the changes in the local evaporation-related moisture flux. The changes in precipitation were also influenced by the changes in the East Asian summer monsoon (EASM) circulation and the corresponding moisture flux, which are expressed in marked subregional characteristics. Therefore, the influence of urban-related precipitation over the three city clusters in China, for which changes in moisture flux from both the impacted local evaporation and EASM circulation should be considered, varied based on the precipitation changes of only a single city.

McLaughlin and Mars. [volcanic-aeolian hypotheses for Martian surface features

NASA Technical Reports Server (NTRS)

Veverka, J.; Sagan, C.

1974-01-01

McLaughlin formulated a novel explanation for the Martian albedo markings and their variations. This explanation, the volcanic-aeolian hypothesis, is one of the very few prespacecraft views of planet-wide phenomena on Mars which have stood the test of time. The distribution of albedo markings is considered along with secular changes on Mars and seasonal changes in region Syrtis Major. Mariner 9 has demonstrated that aeolian transport is the dominant factor in determining the distribution of albedo markings on Mars.

40 CFR 761.302 - Proportion of the total surface area to sample.

Code of Federal Regulations, 2011 CFR

2011-07-01

... surface into approximately 1 meter square portions and mark the portions so that they are clearly... surfaces contaminated by a single source of PCBs with a uniform concentration, assign each 1 meter square surface a unique sequential number. (i) For three or fewer 1 meter square areas, sample all of the areas...

40 CFR 761.302 - Proportion of the total surface area to sample.

Code of Federal Regulations, 2014 CFR

2014-07-01

... surface into approximately 1 meter square portions and mark the portions so that they are clearly... surfaces contaminated by a single source of PCBs with a uniform concentration, assign each 1 meter square surface a unique sequential number. (i) For three or fewer 1 meter square areas, sample all of the areas...

40 CFR 761.302 - Proportion of the total surface area to sample.

Code of Federal Regulations, 2010 CFR

2010-07-01

... surface into approximately 1 meter square portions and mark the portions so that they are clearly... surfaces contaminated by a single source of PCBs with a uniform concentration, assign each 1 meter square surface a unique sequential number. (i) For three or fewer 1 meter square areas, sample all of the areas...

40 CFR 761.302 - Proportion of the total surface area to sample.

Code of Federal Regulations, 2012 CFR

2012-07-01

... surface into approximately 1 meter square portions and mark the portions so that they are clearly... surfaces contaminated by a single source of PCBs with a uniform concentration, assign each 1 meter square surface a unique sequential number. (i) For three or fewer 1 meter square areas, sample all of the areas...

40 CFR 761.302 - Proportion of the total surface area to sample.

Code of Federal Regulations, 2013 CFR

2013-07-01

... surface into approximately 1 meter square portions and mark the portions so that they are clearly... surfaces contaminated by a single source of PCBs with a uniform concentration, assign each 1 meter square surface a unique sequential number. (i) For three or fewer 1 meter square areas, sample all of the areas...

Laser marking as a result of applying reverse engineering

NASA Astrophysics Data System (ADS)

Mihalache, Andrei; Nagîţ, Gheorghe; Rîpanu, Marius Ionuţ; Slǎtineanu, Laurenţiu; Dodun, Oana; Coteaţǎ, Margareta

2018-05-01

The elaboration of a modern manufacturing technology needs a certain quantum of information concerning the part to be obtained. When it is necessary to elaborate the technology for an existing object, such an information could be ensured by using the principles specific to the reverse engineering. Essentially, in the case of this method, the analysis of the surfaces and of other characteristics of the part must offer enough information for the elaboration of the part manufacturing technology. On the other hand, it is known that the laser marking is a processing method able to ensure the transfer of various inscriptions or drawings on a part. Sometimes, the laser marking could be based on the analysis of an existing object, whose image could be used to generate the same object or an improved object. There are many groups of factors able to affect the results of applying the laser marking process. A theoretical analysis was proposed to show that the heights of triangles obtained by means of a CNC marking equipment depend on the width of the line generated by the laser spot on the workpiece surface. An experimental research was thought and materialized to highlight the influence exerted by the line with and the angle of lines intersections on the accuracy of the marking process. By mathematical processing of the experimental results, empirical mathematical models were determined. The power type model and the graphical representation elaborated on the base of this model offered an image concerning the influences exerted by the considered input factors on the marking process accuracy.

Electromagnetic Navigation Bronchoscopy for Identifying Lung Nodules for Thoracoscopic Resection.

PubMed

Marino, Katy A; Sullivan, Jennifer L; Weksler, Benny

2016-08-01

Pulmonary nodules smaller than 1 cm can be difficult to identify during minimally invasive resection, necessitating conversion to thoracotomy. We hypothesized that localizing nodules with electromagnetic navigation bronchoscopy and marking them with methylene blue would allow minimally invasive resection and reduce conversion to thoracotomy. We retrospectively identified all patients who underwent electromagnetic navigation bronchoscopy followed by minimally invasive resection of a pulmonary nodule from 2011 to 2014. Lung nodules smaller than 10 mm and nodules smaller than 20 mm that were also located more than 10 mm from the pleural surface were localized and marked with methylene blue. Immediately after marking, all patients underwent resection. Seventy patients underwent electromagnetic navigation bronchoscopy marking followed by minimally invasive resection. The majority of patients (68/70, 97%) had one nodule localized; 2 patients (2/70, 3%) had two nodules localized. The median nodule size was 8 mm (range, 4-17 mm; interquartile range, 5 mm). The median distance from the pleural surface was 6 mm (range, 1-19 mm; interquartile range, 6 mm). There were no conversions to thoracotomy. Nodule marking was successful in 70 of 72 attempts (97.2%); two nodules were identified by palpation. The nodules were most commonly metastases from other sites (31/70, 44.3%). There were no adverse events related to electromagnetic navigation bronchoscopy-guided marking or wedge resection, and minimal adverse events after resections that were more extensive. Localizing and marking small pulmonary nodules using electromagnetic navigation bronchoscopy is safe and effective for nodule identification before minimally invasive resection. Copyright © 2016 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Noah-MP-Crop: Enhancing cropland representation in the community land surface modeling system

NASA Astrophysics Data System (ADS)

Liu, X.; Chen, F.; Barlage, M. J.; Zhou, G.; Niyogi, D.

2015-12-01

Croplands are important in land-atmosphere interactions and in modifying local and regional weather and climate. Despite their importance, croplands are poorly represented in the current version of the coupled Weather Research and Forecasting (WRF)/ Noah land-surface modeling system, resulting in significant surface temperature and humidity biases across agriculture- dominated regions of the United States. This study aims to improve the WRF weather forecasting and regional climate simulations during the crop growing season by enhancing the representation of cropland in the Noah-MP land model. We introduced dynamic crop growth parameterization into Noah-MP and evaluated the enhanced model (Noah-MP-Crop) at both the field and regional scales with multiple crop biomass datasets, surface fluxes and soil moisture/temperature observations. We also integrated a detailed cropland cover map into WRF, enabling the model to simulate corn and soybean field across the U.S. Great Plains. Results show marked improvement in the Noah-MP-Crop performance in simulating leaf area index (LAI), crop biomass, soil temperature, and surface fluxes. Enhanced cropland representation is not only crucial for improving weather forecasting but can also help assess potential impacts of weather variability on regional hydrometeorology and crop yields. In addition to its applications to WRF, Noah-MP-Crop can be applied in high-spatial-resolution regional crop yield modeling and drought assessments

Optimization of Nd: YAG Laser Marking of Alumina Ceramic Using RSM And ANN

NASA Astrophysics Data System (ADS)

Peter, Josephine; Doloi, B.; Bhattacharyya, B.

2011-01-01

The present research papers deals with the artificial neural network (ANN) and the response surface methodology (RSM) based mathematical modeling and also an optimization analysis on marking characteristics on alumina ceramic. The experiments have been planned and carried out based on Design of Experiment (DOE). It also analyses the influence of the major laser marking process parameters and the optimal combination of laser marking process parametric setting has been obtained. The output of the RSM optimal data is validated through experimentation and ANN predictive model. A good agreement is observed between the results based on ANN predictive model and actual experimental observations.

On the Syntax/Semantics of Korean Nominal Particles

ERIC Educational Resources Information Center

Chung, Han-Byul

2016-01-01

In this dissertation, I investigate the structural positions of "i/ka"-marked DPs and "un/nun"-marked DPs in the light of Kratzer (1988; 1995) and Diesing (1990; 1992). In Korean, unlike German (and English in part), vP-external subjects and vP-internal subjects are not distinguishable at the surface. However, by adopting…

10 CFR 32.15 - Same: Quality assurance, prohibition of transfer, and labeling.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... (2) For ionization chamber smoke detectors, label or mark each detector and its point-of-sale package so that: (i) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (A) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (B) The...

10 CFR 32.15 - Same: Quality assurance, prohibition of transfer, and labeling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... can be identified. (2) For ionization chamber smoke detectors, label or mark each detector and its point-of-sale package so that: (i) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (A) The following statement: “CONTAINS...

10 CFR 32.15 - Same: Quality assurance, prohibition of transfer, and labeling.

Code of Federal Regulations, 2012 CFR

2012-01-01

... can be identified. (2) For ionization chamber smoke detectors, label or mark each detector and its point-of-sale package so that: (i) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (A) The following statement: “CONTAINS...

10 CFR 32.15 - Same: Quality assurance, prohibition of transfer, and labeling.

Code of Federal Regulations, 2011 CFR

2011-01-01

... can be identified. (2) For ionization chamber smoke detectors, label or mark each detector and its point-of-sale package so that: (i) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (A) The following statement: “CONTAINS...

10 CFR 32.15 - Same: Quality assurance, prohibition of transfer, and labeling.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... (2) For ionization chamber smoke detectors, label or mark each detector and its point-of-sale package so that: (i) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (A) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (B) The...

Impacts of Small-Scale Industrialized Swine Farming on Local Soil, Water and Crop Qualities in a Hilly Red Soil Region of Subtropical China

PubMed Central

Zhang, Di; Wang, Xingxiang; Zhou, Zhigao

2017-01-01

Industrialized small-scale pig farming has been rapidly developed in developing regions such as China and Southeast Asia, but the environmental problems accompanying pig farming have not been fully recognized. This study investigated 168 small-scale pig farms and 29 example pig farms in Yujiang County of China to examine current and potential impacts of pig wastes on soil, water and crop qualities in the hilly red soil region, China. The results indicated that the small-scale pig farms produced considerable annual yields of wastes, with medians of 216, 333 and 773 ton yr−1 per pig farm for manure, urine and washing wastewater, respectively, which has had significant impact on surface water quality. Taking NH4+-N, total nitrogen (TN) or total phosphorus (TP) as a criterion to judge water quality, the proportions of Class III and below Class III waters in the local surface waters were 66.2%, 78.7% and 72.5%. The well water (shallow groundwater) quality near these pig farms met the water quality standards by a wide margin. The annual output of pollutants from pig farms was the most important factor correlated with the nutrients and heavy metals in soils, and the relationship can be described by a linear equation. The impact on croplands was marked by the excessive accumulation of available phosphorus and heavy metals such as Cu and Zn. For crop safety, the over-limit ratio of Zn in vegetable samples reached 60%, other heavy metals in vegetable and rice samples tested met the food safety standard at present. PMID:29211053

Impacts of Small-Scale Industrialized Swine Farming on Local Soil, Water and Crop Qualities in a Hilly Red Soil Region of Subtropical China.

PubMed

Zhang, Di; Wang, Xingxiang; Zhou, Zhigao

2017-12-06

Industrialized small-scale pig farming has been rapidly developed in developing regions such as China and Southeast Asia, but the environmental problems accompanying pig farming have not been fully recognized. This study investigated 168 small-scale pig farms and 29 example pig farms in Yujiang County of China to examine current and potential impacts of pig wastes on soil, water and crop qualities in the hilly red soil region, China. The results indicated that the small-scale pig farms produced considerable annual yields of wastes, with medians of 216, 333 and 773 ton yr -1 per pig farm for manure, urine and washing wastewater, respectively, which has had significant impact on surface water quality. Taking NH₄⁺-N, total nitrogen (TN) or total phosphorus (TP) as a criterion to judge water quality, the proportions of Class III and below Class III waters in the local surface waters were 66.2%, 78.7% and 72.5%. The well water (shallow groundwater) quality near these pig farms met the water quality standards by a wide margin. The annual output of pollutants from pig farms was the most important factor correlated with the nutrients and heavy metals in soils, and the relationship can be described by a linear equation. The impact on croplands was marked by the excessive accumulation of available phosphorus and heavy metals such as Cu and Zn. For crop safety, the over-limit ratio of Zn in vegetable samples reached 60%, other heavy metals in vegetable and rice samples tested met the food safety standard at present.

The Four Marks of Holistic Kinesiology

ERIC Educational Resources Information Center

Twietmeyer, Gregg

2012-01-01

What, to borrow a theological phrase, are the marks of a truly holistic kinesiology department? "In Kinesis and the Nature of the Human Person" (2010), I examined the theoretical impact of Aristotle's definition of "kinesis" and Polanyi's theory of "tacit knowledge" on kinesiology. The intention here, however, is practical rather than theoretical.…

Soil nutrient concentration and distribution at riverbanks undergoing different land management practices: Implications for riverbank management

NASA Astrophysics Data System (ADS)

Xue, X. H.; Chang, S.; Yuan, L. Y.

2017-08-01

Riverbanks are important boundaries for the nutrient cycling between lands and freshwaters. This research aimed to explore effects of different land management methods on the soil nutrient concentration and distribution at riverbanks. Soils from the reed-covered riverbanks of middle Yangtze River were studied, including the soils respectively undergoing systematic agriculture (gathering young tender shoots, reaping reed straws, and burning residual straws), fires and no disturbances. Results showed that the agricultural activities sharply decreased the contents of soil organic matter (SOM), N, P and K in subsurface soils but less decreased the surface SOM, N and K contents, whereas phosphorus were evidently decreased at both surface and subsurface layers. In contrast, the single application of fires caused a marked increase of SOM, N, P and K contents in both surface and subsurface soils but had little impacts on soil nutrient distributions. Soils under all the three conditions showed a relative increase of soil nutrients at riverbank foot. This comparative study indicated that the different or even contrary effects of riverbank management practices on soil nutrient statuses should be carefully taken into account when assessing the ecological effects of management practices.

Groundwater potential prediction by using geoelectricity method a case study in Simpang Lima and around it

NASA Astrophysics Data System (ADS)

Rahmawati, D. R.; Supriyadi; Aryani, N. P.; Naufal, M. A.

2018-03-01

Water is an important natural resource, which is available both on surface as well as in recharge zone of weathered layer and in various other suitable water reservoir formations/structures below the surface. The study was conducted in Semarang City, Indonesian. Simpang Lima area were chosen since they have geology record of thick alluvium. The condition of Simpang Lima and around it which currently has developed into the main business area in Semarang City. This is marked by the presence like hotels, super market, that is more than one. This condition certainly requires a supply of water for various purposes that support economic efforts in the region. During this time the water needs are met by drilling wells and used as much as possible without taking into account the impact of water utilization. This study aims to determine the zones that have the potential existence of groundwater. The method used is Geoelectric method with Shlumberger configuration in 7 distributed spatial point. The results showed that there is a potential groundwater in eastern Pekunden, Erlanga, behind The Hotel Horizon, and Simpang Lima. Groundwater is found successively at an average depth of 15 meters under earth’s surface.

GIFAD for He/KCl(001). Structure in the pattern for 〈 110 〉 incidence as a measure of the projectile-cation interaction

NASA Astrophysics Data System (ADS)

Bocan, G. A.; Gravielle, M. S.

2018-04-01

In this article we address grazing incidence fast atom diffraction (GIFAD) for the He/KCl(001) system, for which a systematic experimental study was recently reported [E. Meyer, Ph.D dissertation, Humboldt-Universität, Berlin, Germany, 2015]. Our theoretical model is built from a projectile-surface interaction obtained from Density Functional Theory (DFT) calculations and the Surface Initial-Value Representation (SIVR), which is a semi-quantum approach to describe the scattering process. For incidence along the 〈 100 〉 and 〈 110 〉 directions, we present and discuss the main features of our interaction potential, the dependence of the rainbow angle with the impact energy normal to the surface, and the simulated GIFAD patterns, which reproduce the main aspects of the reported experimental charts. The features of the diffraction charts for He/KCl(001) are related to the averaged equipotential curves of the system and a comparison is established with the case of He/LiF(001). The marked differences observed for 〈 110 〉 incidence are explained as due to the much larger size of the K+ ion relative to that of Li+.

Occlusion issues in early Renaissance art

PubMed Central

Gillam, Barbara

2011-01-01

Early Renaissance painters innovatively attempted to depict realistic three-dimensional scenes. A major problem was to produce the impression of overlap for surfaces that occlude one another in the scene but are adjoined in the picture plane. Much has been written about perspective in art but little about occlusion. Here I examine some of the strategies for depicting occlusion used by early Renaissance painters in relation to ecological considerations and perceptual research. Perceived surface overlap is often achieved by implementing the principle that an occluding surface occludes anything behind it, so that occlusion perception is enhanced by a lack of relationship of occluding contour to occluded contours. Some well-known figure-ground principles are also commonly used to stratify adjoined figures. Global factors that assist this stratification include the placement of figures on a ground plane, a high viewpoint, and figure grouping. Artists of this period seem to have differed on whether to occlude faces and heads, often carefully avoiding doing so. Halos were either eliminated selectively or placed oddly to avoid such occlusions. Finally, I argue that the marked intransitivity in occlusion by architecture in the paintings of Duccio can be related to the issue of perceptual versus cognitive influences on the visual impact of paintings. PMID:23145262

The Hurwitz Enumeration Problem of Branched Covers and Hodge Integrals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Yun S.

We use algebraic methods to compute the simple Hurwitz numbers for arbitrary source and target Riemann surfaces. For an elliptic curve target, we reproduce the results previously obtained by string theorists. Motivated by the Gromov-Witten potentials, we find a general generating function for the simple Hurwitz numbers in terms of the representation theory of the symmetric group S{sub n}. We also find a generating function for Hodge integrals on the moduli space {bar M}{sub g,2} of Riemann surfaces with two marked points, similar to that found by Faber and Pandharipande for the case of one marked point.

Detail view of the leading and top edge of the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of the leading and top edge of the vertical stabilizer of the Orbiter Discovery showing the thermal protection system components with the white Advanced Flexible Reusable Surface Insulation (AFRSI) blanket and the black High-temperature Reusable Surface Insulation (HRSI) tiles along the outer edges. The marks seen on the HRSI tiles are injection point marks and holes for the application of waterproofing material. This view was taken from a service platform in the Orbiter Processing Facility at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Taphonomy of fossils from the hominin-bearing deposits at Dikika, Ethiopia.

PubMed

Thompson, Jessica C; McPherron, Shannon P; Bobe, René; Reed, Denné; Barr, W Andrew; Wynn, Jonathan G; Marean, Curtis W; Geraads, Denis; Alemseged, Zeresenay

2015-09-01

Two fossil specimens from the DIK-55 locality in the Hadar Formation at Dikika, Ethiopia, are contemporaneous with the earliest documented stone tools, and they collectively bear twelve marks interpreted to be characteristic of stone tool butchery damage. An alternative interpretation of the marks has been that they were caused by trampling animals and do not provide evidence of stone tool use or large ungulate exploitation by Australopithecus-grade hominins. Thus, resolving which agents created marks on fossils in deposits from Dikika is an essential step in understanding the ecological and taphonomic contexts of the hominin-bearing deposits in this region and establishing their relevance for investigations of the earliest stone tool use. This paper presents results of microscopic scrutiny of all non-hominin fossils collected from the Hadar Formation at Dikika, including additional fossils from DIK-55, and describes in detail seven assemblages from sieved surface sediment samples. The study is the first taphonomic description of Pliocene fossil assemblages from open-air deposits in Africa that were collected without using only methods that emphasize the selective retention of taxonomically-informative specimens. The sieved assemblages show distinctive differences in faunal representation and taphonomic modifications that suggest they sample a range of depositional environments in the Pliocene Hadar Lake Basin, and have implications for how landscape-based taphonomy can be used to infer past microhabitats. The surface modification data show that no marks on any other fossils resemble in size or shape those on the two specimens from DIK-55 that were interpreted to bear stone tool inflicted damage. A large sample of marks from the sieved collections has characteristics that match modern trampling damage, but these marks are significantly smaller than those on the DIK-55 specimens and have different suites of characteristics. Most are not visible without magnification. The data show that the DIK-55 marks are outliers amongst bone surface damage in the Dikika area, and that trampling is not the most parsimonious interpretation of their origin. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhancement of image contrast by fluorescence in microtechnology

NASA Astrophysics Data System (ADS)

Berndt, Michael; Tutsch, Rainer

2005-06-01

New developments in production technology increasingly focus on hybrid microsystems. Especially for systems with movable components, the process step of assembly is mandatory. In general, the accuracy of positioning of the parts has to be better than 1 μm. This makes specialized and automated production equipment necessary, which can lead to a conflict with the aim of flexibility of the range of products. Design for manufacturing is a well known remedy. Assembly aids are common practice today. These features of the workpieces bear no functionality for the end product but considerably ease certain process steps. By standardization of assembly aids generalized production equipment free from product-specific features could be developed. In our contribution, we demonstrate the photogrammetric determination of the positions of workpieces without reference to their exterior shape, using circular fiducial marks of 150 μm in diameter. The surface properties of the workpieces, however, still have an influence on image formation. As an example, the marks may be hidden by local specular reflections. A solution to this problem is to add an exclusive optical property to the fiducial marks to get an image with high contrast against the surface of the workpiece. In biology and medicine samples are stained with fluorescing dyes to enhance the contrast in optical microscopy. In fluorochromes, light of a characteristic wavelength is emitted after the absorption of light with a shorter wavelength. In our experiments we added a fluorochrome to a common photoresist and coated the surface of the workpiece with a thin layer thereof. Using photolithography as a patterning technique we generated fiducial marks with structures down to 25 μm. These marks can be identified by their characteristic emission wavelength under short-wavelength illumination. Only the fiducial marks remain visible in the images and processing these images is straightforward. The generation of fluorescing patterns by photolithography opens new possibilities for testing and process control in many fields of microtechnology.

Swash mark and grain flow

USGS Publications Warehouse

Sallenger,, Asbury H.

1981-01-01

Swash marks composed entirely of coarse sand are commonly found on coarse-sand beaches. These swash marks are 10 to 30 centimeters in width and a few millimeters to one centimeter in height. Previous observations, mostly on finer-sand beaches, indicate swash marks are seldom over a few millimeters in height and are commonly composed of material readily floated by surface tension (e.g., mica flakes and shell fragments). Swash marks composed of coarse sand have both fining seaward and fining with depth trends in grain size. Apparently, the leading margin of a wave upwash drives a highly concentrated flow of grains in which both grain size and grain velocity decrease with depth. Therefore, large grains are transported at greater velocities than are smaller grains. Thus, at the maximum advance of an upwash, a swash mark is deposited which has the observed fining seaward and fining with depth trends in grain size.

Structural coloration of metallic surfaces with micro/nano-structures induced by elliptical vibration texturing

NASA Astrophysics Data System (ADS)

Yang, Yang; Pan, Yayue; Guo, Ping

2017-04-01

Creating orderly periodic micro/nano-structures on metallic surfaces, or structural coloration, for control of surface apparent color and optical reflectivity has been an exciting research topic over the years. The direct applications of structural coloration include color marking, display devices, and invisibility cloak. This paper presents an efficient method to colorize metallic surfaces with periodic micro/nano-gratings using elliptical vibration texturing. When the tool vibration is coupled with a constant cutting velocity, controlled periodic ripples can be generated due to the overlapping tool trajectory. These periodic ripples with a wavelength near visible spectrum can act as micro-gratings to introduce iridescent colors. The proposed technique also provides a flexible method for color marking of metallic surfaces with arbitrary patterns and images by precise control of the spacing distance and orientation of induced micro/nano-ripples. Theoretical analysis and experimental results are given to demonstrate structural coloration of metals by a direct mechanical machining technique.

Design of a 3-dimensional visual illusion speed reduction marking scheme.

PubMed

Liang, Guohua; Qian, Guomin; Wang, Ye; Yi, Zige; Ru, Xiaolei; Ye, Wei

2017-03-01

To determine which graphic and color combination for a 3-dimensional visual illusion speed reduction marking scheme presents the best visual stimulus, five parameters were designed. According to the Balanced Incomplete Blocks-Law of Comparative Judgment, three schemes, which produce strong stereoscopic impressions, were screened from the 25 initial design schemes of different combinations of graphics and colors. Three-dimensional experimental simulation scenes of the three screened schemes were created to evaluate four different effects according to a semantic analysis. The following conclusions were drawn: schemes with a red color are more effective than those without; the combination of red, yellow and blue produces the best visual stimulus; a larger area from the top surface and the front surface should be colored red; and a triangular prism should be painted as the graphic of the marking according to the stereoscopic impression and the coordination of graphics with the road.

Thermal Instability of Fats Relative to Surface Wettability of Yellow Birchwood (Betula lutea)

Treesearch

Richard W. Hemingway

1969-01-01

The surface wettability and fats of yellow birchwood were examined in an attempt to illustrate how heat-induced changes in wood fats might be related to changes in surface wettability. A marked reduction of surface wettability accompanied heating of yellow birchwood. The degree of water repellency imparted to the wood was highly dependent upon heating temperature and...

Shallow and deep fresh impact craters in Hesperia Planum, Mars

NASA Technical Reports Server (NTRS)

Mouginis-Mark, Peter J.; Hayashi, Joan N.

1993-01-01

The depths of 109 impact craters about 2-16 km in diameter, located on the ridged plains materials of Hesperia Planum, Mars, have been measured from their shadow lengths using digital Viking Orbiter images (orbit numbers 417S-419S) and the PICS computer software. On the basis of their pristine morphology (very fresh lobate ejecta blankets, well preserved rim crests, and lack of superposed impact craters), 57 of these craters have been selected for detailed analysis of their spatial distribution and geometry. We find that south of 30 deg S, craters less than 6.0 km in diameter are markedly shallower than similar-sized craters equatorward of this latitude. No comparable relationship is observed for morphologically fresh craters greater than 6.0 km diameter. We also find that two populations exist for older craters less than 6.0 km diameter. When craters that lack ejecta blankets are grouped on the basis of depth/diameter ratio, the deeper craters also typically lie equatorward of 30 S. We interpret the spatial variation in crater depth/diameter ratios as most likely due to a poleward increase in volatiles within the top 400 m of the surface at the times these craters were formed.

Heterogeneous nano-Fe/Ca/CaO catalytic ozonation for selective surface hydrophilization of plastics containing brominated and chlorinated flame retardants (B/CFRs): separation from automobile shredder residue by froth flotation.

PubMed

Mallampati, Srinivasa Reddy; Lee, Byoung Ho; Mitoma, Yoshiharu; Simion, Cristian

2017-02-01

One method of weakening the inherently hydrophobic surface of plastics relevant to flotation separation is heterogeneous nano-Fe/Ca/CaO catalytic ozonation. Nano-Fe/Ca/CaO-catalyzed ozonation for 15 min efficiently decreases the surface hydrophobicity of brominated and chlorinated flame retardant (B/CFR)-containing plastics (such as acrylonitrile-butadienestyrene (ABS), high-impact polystyrene (HIPS), and polyvinyl chloride (PVC)) in automobile shredder residue (ASR) to such an extent that their flotation ability is entirely depressed. Such a hydrophilization treatment also stimulates the ABS, HIPS, and PVC surface roughness, wetting of the surface, and the thermodynamic equilibrium conditions at the surface and ultimately changes surface polarity. SEM-EDS, AFM, and XPS analyses of the PVC and ABS surfaces demonstrated a marked decrease in [Cl/Br] and a significant increase in the number of hydrophilic groups, such as C-O, C=O, and (C=O)-O. Under froth flotation conditions at 50 rpm, about 99.5 % of ABS and 99.5 % of HIPS in ASR samples settled out, resulting in a purity of 98 and 98.5 % for ABS and HIPS in ASR samples, respectively. Furthermore, at 150 rpm, we also obtained 100 % PVC separation in the settled fraction, with 98 % purity in ASR. Total recovery of non-B/CFR-containing plastics reached nearly 100 % in the floating fraction. The amount of nano-Fe/Ca/CaO reagent employed during ozonation is very small, and additional removal of surface contaminants from the recycled ASR plastic surfaces by ozonation makes the developed process simpler, greener, and more effective.

Graffiti for science: Qualitative detection of erosional patterns through bedrock erosion painting

NASA Astrophysics Data System (ADS)

Beer, Alexander R.; Kirchner, James W.; Turowski, Jens M.

2016-04-01

Bedrock erosion is a crucial constraint on stream channel incision, and hence whole landscape evolution, in steep mountainous terrain and tectonically active regions. Several interacting processes lead to bedrock erosion in stream channels, with hydraulic shear detachment, plucking, and abrasion due to sediment impacts generally being the most efficient. Bedrock topography, together with the sediment tools and cover effects, regulate the rate and spatial pattern of in situ surface change. Measurements of natural bedrock erosion rates are valuable for understanding the underlying process physics, as well as for modelling landscape evolution and designing engineered structures. However, quantifying spatially distributed bedrock erosion rates in natural settings is challenging and few such measurements exist. We studied spatial bedrock erosion in a 30m-long bedrock gorge in the Gornera, a glacial meltwater stream above Zermatt. This stream is flushed episodically with sediment-laden streamflow due to hydropower operations upstream, with negligible discharge in the gorge in between these flushing events. We coated several bedrock surface patches with environmentally safe, and water-insoluble outdoor paint to document the spatial pattern of surface abrasion, or to be more precise, to document its driving forces. During four consecutive years, the change of the painted areas was recorded repeatedly with photographs before the painting was renewed. These photographs visually documented the spatial patterns of vertical erosion (channel incision), of lateral erosion (channel widening) and of downstream-directed erosion (channel clearance). The observed qualitative patterns were verified through comparison to quantitative change detection analyses based on annual high-resolution terrestrial laser scanning surveys of the bedrock surfaces. Comparison of repeated photographs indicated a temporal cover effect and a general height limit of the tools effect above the streambed during flushing events. Further, the photographs clearly show the erosional development of a UFCS (upstream-facing convex surface) feature with an upstream-facing surface full of impact marks, a sharp crest-line, and an adjacent downstream-facing surface preserved from sediment impacts. This pilot study documents that bedrock erosion painting provides an easy, cost-efficient and clear qualitative method for detecting the spatial distribution of bedrock erosion and inferring its controlling factors. Our results show that the susceptibility of a painted surface to abrasion is controlled by its position in the channel and its spatial orientation relative to the sediment-laden flow. Erosion painting is a scientifically useful form of graffiti that could be widely applied in both natural and laboratory settings, providing insight into patterns and processes of erosion.

Webs on surfaces, rings of invariants, and clusters.

PubMed

Fomin, Sergey; Pylyavskyy, Pavlo

2014-07-08

We construct and study cluster algebra structures in rings of invariants of the special linear group action on collections of 3D vectors, covectors, and matrices. The construction uses Kuperberg's calculus of webs on marked surfaces with boundary.

Dynamic properties of a dirt and a synthetic equine racetrack surface measured by a track-testing device.

PubMed

Setterbo, J J; Fyhrie, P B; Hubbard, M; Upadhyaya, S K; Stover, S M

2013-01-01

Racetrack surface is a risk factor for Thoroughbred racehorse injury and death that can be engineered and managed. To investigate the relationship between surface and injury, the mechanical behaviour of dirt and synthetic track surfaces must be quantified. To compare dynamic properties of a dirt and a synthetic surface in situ using a track-testing device designed to simulate equine hoof impact; and to determine the effects of impact velocity, impact angle and repeated impact on dynamic surface behaviour. A track-testing device measured force and displacement during impact into a dirt and a synthetic surface at 3 impact velocities (1.91, 2.30, 2.63 m/s), 2 impact angles (0°, 20° from vertical), and 2 consecutive impacts (initial, repeat). Surfaces were measured at 3 locations/day for 3 days. The effects of surface type, impact velocity, impact angle and impact number on dynamic surface properties were assessed using analysis of variance. Synthetic surface maximum forces, load rates and stiffnesses were 37-67% of dirt surface values. Surfaces were less stiff with lower impact velocities, angled impacts and initial impacts. The magnitude of differences between dirt and synthetic surfaces increased for repeat impacts and higher impact velocities. The synthetic surface was generally softer than the dirt surface. Greatly increased hardness for repeat impacts corroborates the importance of maintenance. Results at different impact velocities suggest that surface differences will persist at higher impact velocities. For both surfaces it is clearly important to prevent horse exposure to precompacted surfaces, particularly during high-speed training when the surface has already been trampled. These data should be useful in coordinating racetrack surface management with racehorse training to prevent injuries. © 2012 EVJ Ltd.

Evidence for young volcanism on Mercury from the third MESSENGER flyby.

PubMed

Prockter, Louise M; Ernst, Carolyn M; Denevi, Brett W; Chapman, Clark R; Head, James W; Fassett, Caleb I; Merline, William J; Solomon, Sean C; Watters, Thomas R; Strom, Robert G; Cremonese, Gabriele; Marchi, Simone; Massironi, Matteo

2010-08-06

During its first two flybys of Mercury, the MESSENGER spacecraft acquired images confirming that pervasive volcanism occurred early in the planet's history. MESSENGER's third Mercury flyby revealed a 290-kilometer-diameter peak-ring impact basin, among the youngest basins yet seen, having an inner floor filled with spectrally distinct smooth plains. These plains are sparsely cratered, postdate the formation of the basin, apparently formed from material that once flowed across the surface, and are therefore interpreted to be volcanic in origin. An irregular depression surrounded by a halo of bright deposits northeast of the basin marks a candidate explosive volcanic vent larger than any previously identified on Mercury. Volcanism on the planet thus spanned a considerable duration, perhaps extending well into the second half of solar system history.

Western Edge of Mars Marth Crater, a Movie Location

NASA Image and Video Library

2015-10-05

In the best-selling novel "The Martian" and the movie based on it, stranded astronaut Mark Watney's adventures take him to the rim of Mawrth Crater. This image from the High Resolution Imaging Science Experiment (HiRISE) camera on NASA's Mars Reconnaissance Orbiter shows the nature of this terrain. The crater rim is not very distinct, and from the Martian surface it would be quite difficult to tell that you are even on the rim of a crater. The terrain is hummocky and rolling, punctuated by smaller impact craters and wind-blown drifts of sand or dust. This view is one image product from HiRISE observation ESP_042252_1930, taken Aug. 1, 2015, at 12.6 degrees north latitude, 355.7 degrees east longitude. http://photojournal.jpl.nasa.gov/catalog/PIA19915

Narp Deletion Blocks Extinction of Morphine Place Preference Conditioning

PubMed Central

Crombag, Hans S; Dickson, Mercy; Dinenna, Megan; Johnson, Alexander W; Perin, Mark S; Holland, Peter C; Baraban, Jay M; Reti, Irving M

2008-01-01

As drug abuse can be viewed as a maladaptive form of neuronal plasticity, attention has focused on defining the synaptic plasticity mechanisms that mediate the long-term effects of these drugs. As Narp is secreted at synaptic sites and binds to the extracellular surface of AMPA receptors, it has been implicated in mediating enduring forms of synaptic plasticity. Accordingly, to assess its potential role in the long-lasting behavioral effects of drugs of abuse, we have investigated the impact of Narp deletion on sustained behavioral responses elicited by repeated morphine administration. Narp knockout mice display normal locomotor sensitization and conditioned place preference, but are markedly resistant to extinction of place preference. Thus, these findings indicate that Narp plays a selective role in extinction, possibly by its effects on AMPA receptor trafficking. PMID:18536700

Optimization of Nd: YAG Laser Marking of Alumina Ceramic Using RSM And ANN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peter, Josephine; Doloi, B.; Bhattacharyya, B.

The present research papers deals with the artificial neural network (ANN) and the response surface methodology (RSM) based mathematical modeling and also an optimization analysis on marking characteristics on alumina ceramic. The experiments have been planned and carried out based on Design of Experiment (DOE). It also analyses the influence of the major laser marking process parameters and the optimal combination of laser marking process parametric setting has been obtained. The output of the RSM optimal data is validated through experimentation and ANN predictive model. A good agreement is observed between the results based on ANN predictive model and actualmore » experimental observations.« less

Interannual Variability of Regional Hadley Circulation Intensity Over Western Pacific During Boreal Winter and Its Climatic Impact Over Asia-Australia Region

NASA Astrophysics Data System (ADS)

Huang, Ruping; Chen, Shangfeng; Chen, Wen; Hu, Peng

2018-01-01

This study investigates interannual variability of boreal winter regional Hadley circulation over western Pacific (WPHC) and its climatic impacts. A WPHC intensity index (WPHCI) is defined as the vertical shear of the divergent meridional winds. It shows that WPHCI correlates well with the El Niño-Southern Oscillation (ENSO). To investigate roles of the ENSO-unrelated part of WPHCI (WPHCIres), variables that are linearly related to the Niño-3 index have been removed. It reveals that meridional sea surface temperature gradient over the western Pacific plays an essential role in modulating the WPHCIres. The climatic impacts of WPHCIres are further investigated. Below-normal (above-normal) precipitation appears over south China (North Australia) when WPHCIres is stronger. This is due to the marked convergence (divergence) anomalies at the upper troposphere, divergence (convergence) at the lower troposphere, and the accompanied downward (upward) motion over south China (North Australia), which suppresses (enhances) precipitation there. In addition, a pronounced increase in surface air temperature (SAT) appears over south and central China when WPHCIres is stronger. A temperature diagnostic analysis suggests that the increase in SAT tendency over central China is primarily due to the warm zonal temperature advection and subsidence-induced adiabatic heating. In addition, the increase in SAT tendency over south China is primarily contributed by the warm meridional temperature advection. Further analysis shows that the correlation of WPHCIres with the East Asian winter monsoon (EAWM) is weak. Thus, this study may provide additional sources besides EAWM and ENSO to improve understanding of the Asia-Australia climate variability.

Alignment of the measurement scale mark during immersion hydrometer calibration using an image processing system.

PubMed

Peña-Perez, Luis Manuel; Pedraza-Ortega, Jesus Carlos; Ramos-Arreguin, Juan Manuel; Arriaga, Saul Tovar; Fernandez, Marco Antonio Aceves; Becerra, Luis Omar; Hurtado, Efren Gorrostieta; Vargas-Soto, Jose Emilio

2013-10-24

The present work presents an improved method to align the measurement scale mark in an immersion hydrometer calibration system of CENAM, the National Metrology Institute (NMI) of Mexico, The proposed method uses a vision system to align the scale mark of the hydrometer to the surface of the liquid where it is immersed by implementing image processing algorithms. This approach reduces the variability in the apparent mass determination during the hydrostatic weighing in the calibration process, therefore decreasing the relative uncertainty of calibration.

Alignment of the Measurement Scale Mark during Immersion Hydrometer Calibration Using an Image Processing System

PubMed Central

Peña-Perez, Luis Manuel; Pedraza-Ortega, Jesus Carlos; Ramos-Arreguin, Juan Manuel; Arriaga, Saul Tovar; Fernandez, Marco Antonio Aceves; Becerra, Luis Omar; Hurtado, Efren Gorrostieta; Vargas-Soto, Jose Emilio

2013-01-01

The present work presents an improved method to align the measurement scale mark in an immersion hydrometer calibration system of CENAM, the National Metrology Institute (NMI) of Mexico, The proposed method uses a vision system to align the scale mark of the hydrometer to the surface of the liquid where it is immersed by implementing image processing algorithms. This approach reduces the variability in the apparent mass determination during the hydrostatic weighing in the calibration process, therefore decreasing the relative uncertainty of calibration. PMID:24284770

An Experimental Technique for Developing Intermediate Strain Rates in Ductile Metals

DTIC Science & Technology

2008-03-01

Smooth the surface of the specimen in the area of the gauge application to provide a surface finish which pro- motes optimum bonding by the adhe- sive...surface of any contamina- tion caused by previous operations such as marking or abrading Conditioner and Cotton Tipped Applicators 5. Neutralizing...Neutralize the surface so the pH of the surface is returned to 7 eliminating any remaining acidity on the specimen surface Neutralizer and Cotton Tipped

Comparative performance of three sampling techniques to detect airborne Salmonella species in poultry farms.

PubMed

Adell, Elisa; Moset, Verónica; Zhao, Yang; Jiménez-Belenguer, Ana; Cerisuelo, Alba; Cambra-López, María

2014-01-01

Sampling techniques to detect airborne Salmonella species (spp.) in two pilot scale broiler houses were compared. Broilers were inoculated at seven days of age with a marked strain of Salmonella enteritidis. The rearing cycle lasted 42 days during the summer. Airborne Salmonella spp. were sampled weekly using impaction, gravitational settling, and impingement techniques. Additionally, Salmonella spp. were sampled on feeders, drinkers, walls, and in the litter. Environmental conditions (temperature, relative humidity, and airborne particulate matter (PM) concentration) were monitored during the rearing cycle. The presence of Salmonella spp. was determined by culture-dependent and molecular methods. No cultivable Salmonella spp. were recovered from the poultry houses' surfaces, the litter, or the air before inoculation. After inoculation, cultivable Salmonella spp. were recovered from the surfaces and in the litter. Airborne cultivable Salmonella spp. Were detected using impaction and gravitational settling one or two weeks after the detection of Salmonella spp. in the litter. No cultivable Salmonella spp. were recovered using impingement based on culture-dependent techniques. At low airborne concentrations, the use of impingement for the quantification or detection of cultivable airborne Salmonella spp. is not recommended. In these cases, a combination of culture-dependent and culture-independent methods is recommended. These data are valuable to improve current measures to control the transmission of pathogens in livestock environments and for optimising the sampling and detection of airborne Salmonella spp. in practical conditions.

AUTOMATIC AIR BURST DIRECTION FINDER

DOEpatents

Allard, G.A.

1952-01-31

This patent application describes an atomic explosion direction indicator comprising a geometric heat-scorchable indicating surface symmetrical about an axis, elevation and azimuth markings on the heat scorchable surface, and an indicating rod at the axis of said surface arranged to cast a shadow hereon, whereby heat from an atomic explosion will scorch a pattern on said surface indicative of the azimuth and elevation of said explosion.

Marked augmentation of PLGA nanoparticle-induced metabolically beneficial impact of γ-oryzanol on fuel dyshomeostasis in genetically obese-diabetic ob/ob mice.

PubMed

Kozuka, Chisayo; Shimizu-Okabe, Chigusa; Takayama, Chitoshi; Nakano, Kaku; Morinaga, Hidetaka; Kinjo, Ayano; Fukuda, Kotaro; Kamei, Asuka; Yasuoka, Akihito; Kondo, Takashi; Abe, Keiko; Egashira, Kensuke; Masuzaki, Hiroaki

2017-11-01

Our previous works demonstrated that brown rice-specific bioactive substance, γ-oryzanol acts as a chaperone, attenuates exaggerated endoplasmic reticulum (ER) stress in brain hypothalamus and pancreatic islets, thereby ameliorating metabolic derangement in high fat diet (HFD)-induced obese diabetic mice. However, extremely low absorption efficiency from intestine of γ-oryzanol is a tough obstacle for the clinical application. Therefore, in this study, to overcome extremely low bioavailability of γ-oryzanol with super-high lipophilicity, we encapsulated γ-oryzanol in polymer poly (DL-lactide-co-glycolide) (PLGA) nanoparticles (Nano-Orz), and evaluated its metabolically beneficial impact in genetically obese-diabetic ob/ob mice, the best-known severest diabetic model in mice. To our surprise, Nano-Orz markedly ameliorated fuel metabolism with an unexpected magnitude (∼1000-fold lower dose) compared with regular γ-oryzanol. Furthermore, such a conspicuous impact was achievable by its administration once every 2 weeks. Besides the excellent impact on dysfunction of hypothalamus and pancreatic islets, Nano-Orz markedly decreased ER stress and inflammation in liver and adipose tissue. Collectively, nanotechnology-based developments of functional foods oriented toward γ-oryzanol shed light on the novel approach for the treatment of a variety of metabolic diseases in humans.

Invisible ink mark detection in the visible spectrum using absorption difference.

PubMed

Lee, Joong; Kong, Seong G; Kang, Tae-Yi; Kim, Byounghyun; Jeon, Oc-Yeub

2014-03-01

One of popular techniques in gambling fraud involves the use of invisible ink marks printed on the back surface of playing cards. Such covert patterns are transparent in the visible spectrum and therefore invisible to unaided human eyes. Invisible patterns can be made visible with ultraviolet (UV) illumination or a CCD camera installed with an infrared (IR) filter depending on the type of ink materials used. Cheating gamers often wear contact lenses or eyeglasses made of IR or UV filters to recognize the secret marks on the playing cards. This paper presents an image processing technique to reveal invisible ink patterns in the visible spectrum without the aid of special equipment such as UV lighting or IR filters. A printed invisible ink pattern leaves a thin coating on the surface with different refractive index for different wavelengths of light, which results in color dispersion or absorption difference. The proposed method finds the differences of color components caused by absorption difference to detect invisible ink patterns on the surface. Experiment results show that the proposed scheme is effective for both UV-active and IR-active invisible ink materials. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Does Surface Topography Play a Role in Taper Damage in Head-neck Modular Junctions?

PubMed

Pourzal, Robin; Hall, Deborah J; Ha, Nguyen Q; Urban, Robert M; Levine, Brett R; Jacobs, Joshua J; Lundberg, Hannah J

2016-10-01

There are increasing reports of total hip arthroplasty failure subsequent to modular taper junction corrosion. The surfaces of tapers are machined to have circumferential machining marks, resulting in a surface topography of alternating peaks and valleys on the scale of micrometers. It is unclear if the geometry of this machined surface topography influences the degree of fretting and corrosion damage present on modular taper junctions or if there are differences between modular taper junction material couples. (1) What are the differences in damage score and surface topography between CoCr/CoCr and CoCr/Ti modular junctions? (2) How are initial surface topography, flexural rigidity, taper angle mismatch, and time in situ related to visual taper damage scores for CoCr/CoCr couples? (3) How are initial surface topography, flexural rigidity, taper angle mismatch, and time in situ related to visual taper damage scores for CoCr/Ti couples? Damage on stem and head tapers was evaluated with a modified Goldberg score. Differences in damage scores were determined between a group of 140 CoCr/CoCr couples and 129 CoCr/Ti couples using a chi-square test. For a subgroup of 70 retrievals, selected at random, we measured five variables, including initial stem taper machining mark height and spacing, initial head taper roughness, flexural rigidity, and taper angle mismatch. All retrievals were obtained at revision surgeries. None were retrieved as a result of metal-on-metal failures or were recalled implants. Components were chosen so there was a comparable number of each material couple and damage score. Machining marks around the circumference of the tapers were measured using white light interferometry to characterize the initial stem taper surface topography in terms of the height of and spacing between machining mark peaks as well as initial head taper roughness. The taper angle mismatch was assessed with a coordinate measuring machine. Flexural rigidity was determined based on measurements of gross taper dimensions and material properties. Differences of median or mean values of all variables between material couples were determined (Wilcoxon rank-sum tests and t-tests). The effect of all five variables along with time in situ on stem and head taper damage scores was tested with a multiple regression model. With 70 retrievals, a statistical power of 0.8 could be achieved for the model. Damage scores were different between CoCr/CoCr and CoCr/Ti modular taper junction material couples. CoCr/CoCr stem tapers were less likely to be mildly damaged (11%, p = 0.006) but more likely to be severely damaged (4%, p = 0.02) than CoCr/Ti stem tapers (28% and 1%, respectively). CoCr/CoCr couples were less likely to have moderately worn head tapers (7% versus 17%, p = 0.003). Stem taper machining mark height and spacing and head taper roughness were 11 (SD 3), 185 (SD 46), and 0.57 (SD 0.5) for CoCr/CoCr couples and 10 (SD 3), 170 (SD 56), and 0.64 (SD 0.4) for CoCr/Ti couples, respectively. There was no difference (p = 0.09, p = 0.1, p = 0.16, respectively) for either factor between material couples. Larger stem taper machining mark heights (p = 0.001) were associated with lower stem taper damage scores, and time in situ (p = 0.006) was associated with higher stem taper damage scores for CoCr/CoCr material couples. Stem taper machining marks that had higher peaks resulted in slower damage progression over time. For CoCr/Ti material couples, head taper roughness was associated with higher stem (p = 0.001) and head taper (p = 0.003) damage scores, and stem taper machining mark height, but not time in situ, was associated with lower stem taper damage scores (p = 0.007). Stem taper surface topography was related to damage scores on retrieved head-neck modular junctions; however, it affected CoCr/CoCr and CoCr/Ti couples differently. A taper topography of circumferential machining marks with higher peaks appears to enable slower damage progression and, subsequently, a reduction of the reported release of corrosion products. This may be of interest to implant designers and manufacturers in an effort to reduce the effects of metal release from modular femoral components.

Spatial dynamics of the invasive defoliator amber-marked birch leafminer across the Anchorage landscape

Treesearch

J.E. Lundquist; R.M. Reich; M. Tuffly

2012-01-01

The amber-marked birch leafminer has caused severe infestations of birch species in Anchorage, AK, since 2002. Its spatial distribution has been monitored since 2006 and summarized using interpolated surfaces based on simple kriging. In this study, we developed methods of assessing and describing spatial distribution of the leafminer as they vary from year to year, and...

10 CFR 32.29 - Conditions of licenses issued under § 32.26: Quality control, labeling, and reports of transfer.

Code of Federal Regulations, 2014 CFR

2014-01-01

... standards approved by the Commission; (b) Label or mark each detector and its point-of-sale package so that: (1) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (i) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (ii) The name...

10 CFR 32.29 - Conditions of licenses issued under § 32.26: Quality control, labeling, and reports of transfer.

Code of Federal Regulations, 2010 CFR

2010-01-01

... standards approved by the Commission; (b) Label or mark each detector and its point-of-sale package so that: (1) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (i) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (ii) The name...

10 CFR 32.29 - Conditions of licenses issued under § 32.26: Quality control, labeling, and reports of transfer.

Code of Federal Regulations, 2011 CFR

2011-01-01

... standards approved by the Commission; (b) Label or mark each detector and its point-of-sale package so that: (1) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (i) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (ii) The name...

10 CFR 32.29 - Conditions of licenses issued under § 32.26: Quality control, labeling, and reports of transfer.

Code of Federal Regulations, 2013 CFR

2013-01-01

... standards approved by the Commission; (b) Label or mark each detector and its point-of-sale package so that: (1) Each detector has a durable, legible, readily visible label or marking on the external surface of the detector containing: (i) The following statement: “CONTAINS RADIOACTIVE MATERIAL”; (ii) The name...

Development of Auxiliaries in Young Children Learning African American English.

PubMed

Newkirk-Turner, Brandi L; Oetting, Janna B; Stockman, Ida J

2016-07-01

We examined language samples of young children learning African American English (AAE) to determine if and when their use of auxiliaries shows dialect-universal and dialect-specific effects. The data were longitudinal language samples obtained from two children, ages 18 to 36 months, and three children, ages 33 to 51 months. Dialect-universal analyses examined age of first form and early uses of BE, DO, and modal auxiliaries. Dialect-specific analyses focused on rates of overt marking by auxiliary type and syntactic construction and for BE by surface form and succeeding element. Initial production of auxiliaries occurred between 19 and 24 months. The children's forms were initially restricted and produced in syntactically simple constructions. Over time, they were expanded in ways that showed their rates of marking to vary by auxiliary type, their rates of BE and DO marking to vary by syntactic construction, and their rates of BE marking to vary by surface form and succeeding element. Development of auxiliaries by young children learning AAE shows both dialect-universal and dialect-specific effects. The findings are presented within a development chart to guide clinicians in the assessment of children learning AAE and in the treatment of AAE-speaking children with language impairment.

The global impact distribution of Near-Earth objects

NASA Astrophysics Data System (ADS)

Rumpf, Clemens; Lewis, Hugh G.; Atkinson, Peter M.

2016-02-01

Asteroids that could collide with the Earth are listed on the publicly available Near-Earth object (NEO) hazard web sites maintained by the National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA). The impact probability distribution of 69 potentially threatening NEOs from these lists that produce 261 dynamically distinct impact instances, or Virtual Impactors (VIs), were calculated using the Asteroid Risk Mitigation and Optimization Research (ARMOR) tool in conjunction with OrbFit. ARMOR projected the impact probability of each VI onto the surface of the Earth as a spatial probability distribution. The projection considers orbit solution accuracy and the global impact probability. The method of ARMOR is introduced and the tool is validated against two asteroid-Earth collision cases with objects 2008 TC3 and 2014 AA. In the analysis, the natural distribution of impact corridors is contrasted against the impact probability distribution to evaluate the distributions' conformity with the uniform impact distribution assumption. The distribution of impact corridors is based on the NEO population and orbital mechanics. The analysis shows that the distribution of impact corridors matches the common assumption of uniform impact distribution and the result extends the evidence base for the uniform assumption from qualitative analysis of historic impact events into the future in a quantitative way. This finding is confirmed in a parallel analysis of impact points belonging to a synthetic population of 10,006 VIs. Taking into account the impact probabilities introduced significant variation into the results and the impact probability distribution, consequently, deviates markedly from uniformity. The concept of impact probabilities is a product of the asteroid observation and orbit determination technique and, thus, represents a man-made component that is largely disconnected from natural processes. It is important to consider impact probabilities because such information represents the best estimate of where an impact might occur.

Asteroid Apophis: Evaluating the impact hazards of such bodies

NASA Astrophysics Data System (ADS)

Shuvalov, V. V.; Svettsov, V. V.; Artem'eva, N. A.; Trubetskaya, I. A.; Popova, O. P.; Glazachev, D. O.

2017-01-01

Soon after the discovery of asteroid 99942 Apophis, it was classified as a potentially hazardous object with a high probability of an impact on the Earth in 2029. Although subsequent observations have substantially reduced the probability of a collision, it has not been ruled out; moreover, similar-sized asteroids in orbits intersecting the Earth's orbit may well be discovered in the near future. We conduct a numerical simulation of an atmospheric passage and an impact on the Earth's surface of a stony cosmic body with a diameter of 300 m and kinetic energy of about 1000 Mt, which roughly corresponds to the parameters of the asteroid Apophis, at atmospheric entry angles of 90° (vertical stroke), 45°, and 30°. The simulation is performed by solving three-dimensional equations of hydrodynamics and radiative transfer equations in the approximations of radiative heat conduction and volume emission. The following hazards are considered: an air shock wave, ejecta from the crater, thermal radiation, and ionospheric disturbances. Our calculations of the overpressure and wind speed on the Earth's surface show that the zone of destruction of the weakest structures can be as large as 700-1000 km in diameter; a decrease in the flight path angle to the surface leads to a marked increase in the area affected by the shock wave. The ionospheric disturbances are global in nature and continue for hours: at distances of several thousand kilometers at altitudes of more than 100 km, air density disturbances are tens of percent and the vertical and horizontal velocity components reach hundreds of meters per second. The impact of radiation on objects on the Earth's surface is estimated by solving the equation of radiative transfer along rays passing through a luminous area. In clear weather, the size of the zone where thermal heating may ignite wood can be as large as 200 km, and the zone of individual fire outbreaks associated with the ignition of flammable materials can be twice as large. In the 100-km central area, which is characterized by very strong thermal damage, there is ignition of structures, roofs, clothes, etc. The human hazardous area increases with the decrease in the trajectory angle, and people may experience thermal effects at distances of up to 250-400 km from the crater.

Development of a Land Use Database for the Little Blackwater Watershed, Dorchester County, Maryland

USGS Publications Warehouse

Milheim, Lesley E.; Jones, John W.; Barlow, Roger A.

2007-01-01

Many agricultural and forested areas in proximity to National Wildlife Refuges (NWR) are under increasing economic pressure to develop lands for commercial or residential development. The upper portion of the Little Blackwater River watershed - a 27 square mile area within largely low-lying Dorchester County, Maryland, on the eastern shore of the Chesapeake Bay - is important to the U.S. Fish and Wildlife Service (USFWS) because it flows toward the Blackwater National Wildlife Refuge (BNWR), and developmental impacts of areas upstream from the BNWR are unknown. One of the primary concerns for the refuge is how storm-water runoff may affect living resources downstream. The Egypt Road project (fig. 1), for which approximately 600 residential units have been approved, has the potential to markedly change the land use and land cover on the west bank of the Little Blackwater River. In an effort to limit anticipated impacts, the Maryland Department of Natural Resources (Maryland DNR) recently decided to purchase some of the lands previously slated for development. Local topography, a high water table (typically 1 foot or less below the land surface), and hydric soils present a challenge for the best management of storm-water flow from developed surfaces. A spatial data coordination group was formed by the Dorchester County Soil and Conservation District to collect data to aid decisionmakers in watershed management and on the possible impacts of development on this watershed. Determination of streamflow combined with land cover and impervious-surface baselines will allow linking of hydrologic and geologic factors that influence the land surface. This baseline information will help planners, refuge managers, and developers discuss issues and formulate best management practices to mitigate development impacts on the refuge. In consultation with the Eastern Region Geospatial Information Office, the dataset selected to be that baseline land cover source was the June-July 2005 National Agricultural Imagery Program (NAIP) 1-meter resolution orthoimagery of Maryland. This publicly available, statewide dataset provided imagery corresponding to the closest in time to the installation of a U.S. Geological Survey (USGS) Water Resources Discipline gaging station on the Little Blackwater River. It also captures land cover status just before major residential development occurs. This document describes the process used to create a land use database for the Little Blackwater watershed.

Hydraulic "fracking": are surface water impacts an ecological concern?

PubMed

Burton, G Allen; Basu, Niladri; Ellis, Brian R; Kapo, Katherine E; Entrekin, Sally; Nadelhoffer, Knute

2014-08-01

Use of high-volume hydraulic fracturing (HVHF) in unconventional reservoirs to recover previously inaccessible oil and natural gas is rapidly expanding in North America and elsewhere. Although hydraulic fracturing has been practiced for decades, the advent of more technologically advanced horizontal drilling coupled with improved slickwater chemical formulations has allowed extensive natural gas and oil deposits to be recovered from shale formations. Millions of liters of local groundwaters are utilized to generate extensive fracture networks within these low-permeability reservoirs, allowing extraction of the trapped hydrocarbons. Although the technology is relatively standardized, the geographies and related policies and regulations guiding these operations vary markedly. Some ecosystems are more at risk from these operations than others because of either their sensitivities or the manner in which the HVHF operations are conducted. Generally, the closer geographical proximity of the susceptible ecosystem to a drilling site or a location of related industrial processes, the higher the risk of that ecosystem being impacted by the operation. The associated construction of roads, power grids, pipelines, well pads, and water-extraction systems along with increased truck traffic are common to virtually all HVHF operations. These operations may result in increased erosion and sedimentation, increased risk to aquatic ecosystems from chemical spills or runoff, habitat fragmentation, loss of stream riparian zones, altered biogeochemical cycling, and reduction of available surface and hyporheic water volumes because of withdrawal-induced lowering of local groundwater levels. The potential risks to surface waters from HVHF operations are similar in many ways to those resulting from agriculture, silviculture, mining, and urban development. Indeed, groundwater extraction associated with agriculture is perhaps a larger concern in the long term in some regions. Understanding the ecological impacts of these anthropogenic activities provides useful information for evaluations of potential HVHF hazards. Geographic information system-based modeling combined with strategic site monitoring has provided insights into the relative importance of these and other ecoregion and land-use factors in discerning potential HVHF impacts. Recent findings suggest that proper siting and operational controls along with strategic monitoring can reduce the potential for risks to aquatic ecosystems. Nevertheless, inadequate data exist to predict ecological risk at this time. The authors suggest considering the plausibility of surface water hazards associated with the various HVHF operations in terms of the ecological context and in the context of relevant anthropogenic activities. © 2014 SETAC.

Bite mark documentation and analysis: the forensic 3D/CAD supported photogrammetry approach.

PubMed

Thali, M J; Braun, M; Markwalder, Th H; Brueschweiler, W; Zollinger, U; Malik, Naseem J; Yen, K; Dirnhofer, R

2003-08-12

Bite mark identification is based on the individuality of a dentition, which is used to match a bite mark to a suspected perpetrator. This matching is based on a tooth-by-tooth and arch-to-arch comparison utilising parameters of size, shape and alignment. The most common method used to analyse bite mark are carried out in 2D space. That means that the 3D information is preserved only two dimensionally with distortions. This paper presents a new 3D documentation, analysis and visualisation approach based on forensic 3D/CAD supported photogrammetry (FPHG) and the use of a 3D surface scanner. Our photogrammetric approach and the used visualisation method is, to the best to our knowledge, the first 3D approach for bite mark analysis in an actual case. The documentation has no distortion artifacts as can be found with standard photography. All the data are documented with a metric 3D measurement, orientation and subsequent analysis in 3D space. Beside the metrical analysis between bite mark and cast, it is possible using our method to utilise the topographical 3D feature of each individual tooth. This means that the 3D features of the biting surfaces and edges of each teeth are respected which is--as shown in our case--very important especially in the front teeth which have the first contact to the skin. Based upon the 3D detailed representation of the cast with the 3D topographic characteristics of the teeth, the interaction with the 3D documented skin can be visualised and analysed on the computer screen.

Factors influencing survival and mark retention in postmetamorphic boreal chorus frogs

USGS Publications Warehouse

Swanson, Jennifer E; Bailey, Larissa L.; Muths, Erin L.; Funk, W. Chris

2013-01-01

The ability to track individual animals is crucial in many field studies and often requires applying marks to captured individuals. Toe clipping has historically been a standard marking method for wild amphibian populations, but more recent marking methods include visual implant elastomer and photo identification. Unfortunately, few studies have investigated the influence and effectiveness of marking methods for recently metamorphosed individuals and as a result little is known about this life-history phase for most amphibians. Our focus was to explore survival probabilities, mark retention, and mark migration in postmetamorphic Boreal Chorus Frogs (Psuedacris maculata) in a laboratory setting. One hundred forty-seven individuals were assigned randomly to two treatment groups or a control group. Frogs in the first treatment group were marked with visual implant elastomer, while frogs in the second treatment group were toe clipped. Growth and mortality were recorded for one year and resulting data were analyzed using known-fate models in Program MARK. Model selection results suggested that survival probabilities of frogs varied with time and showed some variation among marking treatments. We found that frogs with multiple toes clipped on the same foot had lower survival probabilities than individuals in other treatments, but individuals can be marked by clipping a single toe on two different feet without any mark loss or negative survival effects. Individuals treated with visual implant elastomer had a mark migration rate of 4% and mark loss rate of 6%, and also showed very little negative survival impacts relative to control individuals.

Hypervelocity impacts into ice-topped layered targets: Investigating the effects of ice crust thickness and subsurface density on crater morphology

NASA Astrophysics Data System (ADS)

Harriss, Kathryn H.; Burchell, Mark J.

2017-07-01

Many bodies in the outer solar system are theorized to have an ice shell with a different subsurface material below, be it chondritic, regolith, or a subsurface ocean. This layering can have a significant influence on the morphology of impact craters. Accordingly, we have undertaken laboratory hypervelocity impact experiments on a range of multilayered targets, with interiors of water, sand, and basalt. Impact experiments were undertaken using impact speeds in the range of 0.8-5.3 km s-1, a 1.5 mm Al ball bearing projectile, and an impact incidence of 45°. The surface ice crust had a thickness between 5 and 50 mm, i.e., some 3-30 times the projectile diameter. The thickness of the ice crust as well as the nature of the subsurface layer (liquid, well consolidated, etc.) have a marked effect on the morphology of the resulting impact crater, with thicker ice producing a larger crater diameter (at a given impact velocity), and the crater diameter scaling with impact speed to the power 0.72 for semi-infinite ice, but with 0.37 for thin ice. The density of the subsurface material changes the structure of the crater, with flat crater floors if there is a dense, well-consolidated subsurface layer (basalt) or steep, narrow craters if there is a less cohesive subsurface (sand). The associated faulting in the ice surface is also dependent on ice thickness and the substrate material. We find that the ice layer (in impacts at 5 km s-1) is effectively semi-infinite if its thickness is more than 15.5 times the projectile diameter. Below this, the crater diameter is reduced by 4% for each reduction in ice layer thickness equal to the impactor diameter. Crater depth is also affected. In the ice thickness region, 7-15.5 times the projectile diameter, the crater shape in the ice is modified even when the subsurface layer is not penetrated. For ice thicknesses, <7 times the projectile diameter, the ice layer is breached, but the nature of the resulting crater depends heavily on the subsurface material. If the subsurface is noncohesive (loose) material, a crater forms in it. If it is dense, well-consolidated basalt, no crater forms in the exposed subsurface layer.

Simulating the Reiner Gamma Lunar Swirl: Solar Wind Standoff Works!

NASA Astrophysics Data System (ADS)

Deca, Jan; Divin, Andrey; Lue, Charles; Ahmadi, Tara; Horányi, Mihály

2017-04-01

Discovered by early astronomers during the Renaissance, the Reiner Gamma formation is a prominent lunar surface feature. Observations have shown that the tadpole-shaped albedo marking, or swirl, is co-located with one of the strongest crustal magnetic anomalies on the Moon. The region therefore presents an ideal test case to constrain the kinetic solar wind interaction with lunar magnetic anomalies and its possible consequences for lunar swirl formation. All known swirls have been associated with magnetic anomalies, but the opposite does not hold. The evolutionary scenario of the lunar albedo markings has been under debate since the Apollo era. By coupling fully kinetic simulations with a surface vector mapping model based on Kaguya and Lunar Prospector magnetic field measurements, we show that solar wind standoff is the dominant process to have formed the lunar swirls. It is an ion-electron kinetic interaction mechanism that locally prevents weathering by solar wind ions and the subsequent formation of nanophase iron. The correlation between the surface weathering process and the surface reflectance is optimal when evaluating the proton energy flux, rather than the proton density or number flux. This is an important result to characterise the primary process for surface darkening. In addition, the simulated proton reflection rate is for the first time directly compared with in-orbit flux measurements from the SARA:SWIM ion sensor onboard the Chandrayaan-1 spacecraft. The agreement is found excellent. Understanding the relation between the lunar surface albedo features and the co-located magnetic anomaly is essential for our interpretation of the Moon's geological history, space weathering, and to evaluate future lunar exploration opportunities. This work was supported in part by NASA's Solar System Exploration Research Virtual Institute (SSERVI): Institute for Modeling Plasmas, Atmosphere, and Cosmic Dust (IMPACT). The work by C.L. was supported by NASA grant NNX15AP89G. Resources were provided by the NASA High-End Computing (HEC) Program through the NASA Advanced Supercomputing (NAS) Division at Ames Research Center. Part of this work was inspired by discussions within International Team 336: "Plasma Surface Interactions with Airless Bodies in Space and the Laboratory" at the International Space Science Institute, Bern, Switzerland. The LRO-WAC data are publicly available from the NASA PDS Imaging Node. The Wind/MFI and Wind/SWE data used in this study are available via the NASA National Space Science Data Center, Space Physics Data Facility, and the MIT Space Plasma Group. The Chandrayaan-1/SARA data are available via the Indian Space Science Data Center.

Automatic Extraction of Road Markings from Mobile Laser-Point Cloud Using Intensity Data

NASA Astrophysics Data System (ADS)

Yao, L.; Chen, Q.; Qin, C.; Wu, H.; Zhang, S.

2018-04-01

With the development of intelligent transportation, road's high precision information data has been widely applied in many fields. This paper proposes a concise and practical way to extract road marking information from point cloud data collected by mobile mapping system (MMS). The method contains three steps. Firstly, road surface is segmented through edge detection from scan lines. Then the intensity image is generated by inverse distance weighted (IDW) interpolation and the road marking is extracted by using adaptive threshold segmentation based on integral image without intensity calibration. Moreover, the noise is reduced by removing a small number of plaque pixels from binary image. Finally, point cloud mapped from binary image is clustered into marking objects according to Euclidean distance, and using a series of algorithms including template matching and feature attribute filtering for the classification of linear markings, arrow markings and guidelines. Through processing the point cloud data collected by RIEGL VUX-1 in case area, the results show that the F-score of marking extraction is 0.83, and the average classification rate is 0.9.

The impact of faceplate surface characteristics on detection of pulmonary nodules

NASA Astrophysics Data System (ADS)

Toomey, R. J.; Ryan, J. T.; McEntee, M. F.; McNulty, J.; Evanoff, M. G.; Cuffe, F.; Yoneda, T.; Stowe, J.; Brennan, P. C.

2009-02-01

Introduction In order to prevent specular reflections, many monitor faceplates have features such as tiny dimples on their surface to diffuse ambient light incident on the monitor, however, this "anti-glare" surface may also diffuse the image itself. The purpose of the study was to determine whether the surface characteristics of monitor faceplates influence the detection of pulmonary nodules under low and high ambient lighting conditions. Methods and Materials Separate observer performance studies were conducted at each of two light levels (<1 lux and >250 lux). Twelve examining radiologists with the American Board of Radiology participated in the darker condition and eleven in the brighter condition. All observers read on both smooth "glare" and dimpled "anti-glare" faceplates in a single lighting condition. A counterbalanced methodology was utilized to minimise memory effects. In each reading, observers were presented with thirty chest images in random order, of which half contained a single simulated pulmonary nodule. They were asked to give their confidence that each image did or did not contain a nodule and to mark the suspicious location. ROC analysis was applied to resultant data. Results No statistically significant differences were seen in the trapezoidal area under the ROC curve (AUC), sensitivity, specificity or average time per case at either light level for chest specialists or radiologists from other specialities. Conclusion The characteristics of the faceplate surfaces do not appear to affect detection of pulmonary nodules. Further work into other image types is being conducted.

Validation of photo-identification as a mark-recapture method in the spotted eagle ray Aetobatus narinari.

PubMed

González-Ramos, M S; Santos-Moreno, A; Rosas-Alquicira, E F; Fuentes-Mascorro, G

2017-03-01

The spotted eagle ray Aetobatus narinari is characterized by pigmentation patterns that are retained for up to 3·5 years. These pigmentations can be used to identify individuals through photo-identification. Only one study has validated this technique, but no study has estimated the percentage of correct identification of the rays using this technique. In order to carry out demographic research, a reliable photographic identification technique is needed. To achieve this validation for A. narinari, a double-mark system was established over 11 months and photographs of the dorsal surface of 191 rays were taken. Three body parts with distinctive natural patterns were analysed (dorsal surface of the cephalic region, dorsal surface of the pectoral fins and dorsal surface of the pelvic fins) in order to determine the body part that could be used to give the highest percentage of correct identification. The dorsal surface of the pectoral fins of A. narinari provides the most accurate photo-identification to distinguish individuals (88·2%). © 2016 The Fisheries Society of the British Isles.

Ultrafast lasers for precise and corrosion free marking on chirurgical steels

NASA Astrophysics Data System (ADS)

Neugebauer, Christoph; Aalderink, Dennis; Maurer, Erich; Faisst, Birgit; Budnicki, Aleksander

2017-02-01

The unique properties of ultrashort laser pulses and the decrease of invest pave the way to numerous novel applications. Even in the very price sensitive field of laser marking, ultrashort laser can compete due to a new cost structure and remarkable properties of the marking results. In this study we concentrated on industrial marking of medical equipment by using IR ultrashort lasers and compared the results with common marking laser systems. We demonstrate the benefits of ultrashort lasers marking on chirurgical devices, observing the influence of pulse energy, pulse duration, scanning velocity in respect to the visibility, corrosion resistance and long term durability under clinical conditions. Nowadays many parts and products are marked for the purpose of identification and traceability. One kind of laser marking is the well known annealing of stainless steel by nanosecond marking lasers. When annealing occurs a colored oxide layer grows due to the local heating of the material surface. Compared to the raw material, the annealed marking shows increased corrosion sensitivity. Regarding the traceability, the poor durability of the ns marking resulting in contrast reduction and the corrosion susceptibility are a huge problem. Therefore three different laser sources with ns-psfs pulse duration were observed. The focus rests on the realization of parameter studies (various lasers) and their effect on the corrosion and passivation behavior. Furthermore analysis of the oxide layers by use of EDX and XRD were performed to obtain further information on the composition and structure of the markings.

Distinctive colonization of Bacillus sp. bacteria and the influence of the bacterial biofilm on electrochemical behaviors of aluminum coatings.

PubMed

Abdoli, Leila; Suo, Xinkun; Li, Hua

2016-09-01

Formation of biofilm is usually essential for the development of biofouling and crucially impacts the corrosion of marine structures. Here we report the attachment behaviors of Bacillus sp. bacteria and subsequent formation of bacterial biofilm on stainless steel and thermal sprayed aluminum coatings in artificial seawater. The colonized bacteria accelerate the corrosion of the steel plates, and markedly enhance the anti-corrosion performances of the Al coatings in early growth stage of the bacterial biofilm. After 7days incubation, the biofilm formed on the steel is heterogeneous while exhibits homogeneous feature on the Al coating. Atomic force microscopy examination discloses inception of formation of local pitting on steel plates associated with significantly roughened surface. Electrochemical testing suggests that the impact of the bacterial biofilm on the corrosion behaviors of marine structures is not decided by the biofilm alone, it is instead attributed to synergistic influence by both the biofilm and physicochemical characteristics of the substratum materials. Copyright © 2016 Elsevier B.V. All rights reserved.

Playing with inclined circular hydraulic jumps

NASA Astrophysics Data System (ADS)

Lebon, Luc; Saget, Beryl; Durand, Marc; Limat, Laurent; Couder, Yves; Receveur, Mathieu

2008-11-01

We have investigated the structure of the circular hydraulic jump, when the jet impacts an inclined plate. At low plate slope, quasi-circular shapes, evolving towards elliptic shapes are observed. At moderate inclinations, the upper and lower jumps become markedly different, and the lower jump is even rejected to infinity when a critical inclination is reached. Above this critical inclination, the jump is coupled to an outer dewetting contact line to give a specific object (expanding impact sheet feeding a curved rim in which the liquid is flowing tangentially). In this regime, both the position and curvature of the upper jump follows unusual scalings with the flow rate that completely differ from those observed on horizontal plates. Finally we have looked to metastable drops trapped in the circular jump at very small inclinations. As reported in a previous APS, the lowest position in the jump can become unstable and the drops oscillate around the jump perimeter. We show that this behavior requires very specific conditions of surface tension and viscosity and propose simple interpretations for the instability mechanism.

Everlasting Dark Printing on Alumina by Laser

NASA Astrophysics Data System (ADS)

Penide, J.; Quintero, F.; Arias-González, F.; Fernández, A.; del Val, J.; Comesaña, R.; Riveiro, A.; Lusquiños, F.; Pou, J.

Marks or prints are needed in almost every material, mainly for decorative or identification purposes. Despite alumina is widely employed in many different industries, the need of printing directly on its surface is still a complex problem. In this sense, lasers have largely demonstrated their high capacities to mark almost every material including ceramics, but performing dark permanent marks on alumina is still an open challenge. In this work we present the results of a comprehensive experimental analysis on the process of marking alumina by laser. Four different laser sources were used in this study: a fiber laser (1075 nm) and three diode pumped Nd:YVO4 lasers emitting at near-infrared (1064 nm), visible (532 nm) and ultraviolet (355 nm) wavelengths, respectively. The results obtained with the four lasers were compared and physical processes involved were explained in detail. Colorimetric analyses allowed to identify the optimal parameters and conditions to produce everlasting and high contrast marks on alumina.

Multipurpose Scribing and Drawing Tool

NASA Technical Reports Server (NTRS)

Ellis, J. M.

1986-01-01

Two-part tool reconfigured for variety of jobs. Tool performs several functions useful in layout. Lines, curves, and angles made visible as either bright scribe marks or as dark pencil (or ink) marks. Multipurpose tool speeds up laying out of patterns on sheet metal, wood, plastic, or paper. Tool is carried in pocket, then quickly assembled for service as height gauge, pair of dividers, protractor, surface gauge, or square.

A Primer on Vibrational Ball Bearing Feature Generation for Prognostics and Diagnostics Algorithms

DTIC Science & Technology

2015-03-01

Atlas -Marks (Cone-Shaped Kernel) ........................................................36 8.7.7 Hilbert-Huang Transform...bearing surface and eventually progress to the surface where the material will separate. Also known as pitting, spalling, or flaking. • Wear ...normal degradation caused by dirt and foreign particles causing abrasion of the contact surfaces over time resulting in alterations in the raceway and

Lenticular card: a new method for denture identification.

PubMed

Colvenkar, Shreya S

2010-01-01

The need for denture marking is important for forensic and social reasons in case patients need to be identified individually. Majority of the surface marking and inclusion techniques are expensive, time consuming, and do not permit the incorporation of large amounts of information. In this article, the method to include a lenticular identification card stood out from the currently available denture marking methods in various ways. The lenticular card stores the patient's information has two or more images that can be viewed by changing the angle of view. The maxillary denture was processed according to the manufacturer's instructions. The lenticular identification card was incorporated in the external posterior buccal surface of the maxillary denture using salt and pepper technique. For testing of durability, denture with the identifier was placed in water for up to 4 months. The proposed method is simple, cheap, and can store a large amount of information, thus allowing quick identification of the denture wearer. The labels showed no sign of fading or deterioration.

Flood recovery maps for the White River in Bethel, Stockbridge, and Rochester, Vermont, and the Tweed River in Stockbridge and Pittsfield, Vermont, 2014

USGS Publications Warehouse

Olson, Scott A.

2015-01-01

Eighteen high-water marks from Tropical Storm Irene were available along the studied reaches. The discharges in the Tropical Storm Irene HEC–RAS model were adjusted so that the resulting water-surface elevations matched the high-water mark elevations along the study reaches. This allowed for an estimation of the water-surface profile throughout the study area resulting from Tropical Storm Irene. From a comparison of the estimated water-surface profile of Tropical Storm Irene to the water-surface profiles of the 1- and 0.2-percent AEP floods, it was determined that the high-water elevations resulting from Tropical Storm Irene exceeded the estimated 1-percent AEP flood throughout the White River and Tweed River study reaches and exceeded the estimated 0.2-percent AEP flood in 16.7 of the 28.6 study reach miles. The simulated water-surface profiles were then combined with a geographic information system digital elevation model derived from light detection and ranging (lidar) data having a 18.2-centimeter vertical accuracy at the 95-percent confidence level and 1-meter horizontal resolution to delineate the area flooded for each water-surface profile.

Impact of anatomical parameters on optical coherence tomography retinal nerve fiber layer thickness abnormality patterns

NASA Astrophysics Data System (ADS)

Baniasadi, Neda; Wang, Mengyu; Wang, Hui; Jin, Qingying; Mahd, Mufeed; Elze, Tobias

2017-02-01

Purpose: To evaluate the effects of four anatomical parameters (angle between superior and inferior temporal retinal arteries [inter-artery angle, IAA], optic disc [OD] rotation, retinal curvature, and central retinal vessel trunk entry point location [CRVTL]) on retinal nerve fiber layer thickness (RNFLT) abnormality marks by OCT machines. Methods: Cirrus OCT circumpapillary RNFLT measurements and Humphrey visual fields (HVF 24-2) of 421 patients from a large glaucoma clinic were included. Ellipses were fitted to the OD borders. Ellipse rotation relative to the vertical axis defined OD rotation. CRVTL was manually marked on the horizontal axis of the ellipse on the OCT fundus image. IAA was calculated between manually marked retinal artery locations at the 1.73mm radius around OD. Retinal curvature was determined by the inner limiting membrane on the horizontal B-scan closest to the OD center. For each location on the circumpapillary scanning area, logistic regression was used to determine if each of the four parameters had a significant impact on RNFLT abnormality marks independent of disease severity. The results are presented on spatial maps of the entire scanning area. Results: Variations in IAA significantly influenced abnormality marks on 38.8% of the total scanning area, followed by CRVTL (19.2%) and retinal curvature (18.7%). The effect of OD rotation was negligible (<1%). Conclusions: A natural variation in IAA, retinal curvature, and CRVTL can affect OCT abnormality ratings, which may bias clinical diagnosis. Our spatial maps may help OCT manufacturers to introduce location specific norms to ensure that abnormality marks indicate ocular disease instead of variations in eye anatomy.

Improved representations of coupled soil–canopy processes in the CABLE land surface model (Subversion revision 3432)

DOE PAGES

Haverd, Vanessa; Cuntz, Matthias; Nieradzik, Lars P.; ...

2016-09-07

CABLE is a global land surface model, which has been used extensively in offline and coupled simulations. While CABLE performs well in comparison with other land surface models, results are impacted by decoupling of transpiration and photosynthesis fluxes under drying soil conditions, often leading to implausibly high water use efficiencies. Here, we present a solution to this problem, ensuring that modelled transpiration is always consistent with modelled photosynthesis, while introducing a parsimonious single-parameter drought response function which is coupled to root water uptake. We further improve CABLE's simulation of coupled soil–canopy processes by introducing an alternative hydrology model with amore » physically accurate representation of coupled energy and water fluxes at the soil–air interface, including a more realistic formulation of transfer under atmospherically stable conditions within the canopy and in the presence of leaf litter. The effects of these model developments are assessed using data from 18 stations from the global eddy covariance FLUXNET database, selected to span a large climatic range. Here, marked improvements are demonstrated, with root mean squared errors for monthly latent heat fluxes and water use efficiencies being reduced by 40 %. Results highlight the important roles of deep soil moisture in mediating drought response and litter in dampening soil evaporation.« less

A Possible Cause for Recent Decadal Atlantic Meridional Overturning Circulation Decline

NASA Astrophysics Data System (ADS)

Latif, Mojib; Park, Taewook; Park, Wonsun

2017-04-01

The Atlantic Meridional Overturning Circulation (AMOC) is a major oceanic current system with widespread climate impacts. AMOC influences have been discussed among others with regard to Atlantic hurricane activity, regional sea level variability, and surface air temperature and precipitation changes on land areas adjacent to the North Atlantic Ocean. Most climate models project significant AMOC slowing during the 21st century, if atmospheric greenhouse gas concentrations continue to rise unabatedly. Recently, a marked decadal decline in AMOC strength has been observed, which was followed by strongly reduced oceanic poleward heat transport and record low sea surface temperature in parts of the North Atlantic. Here, we provide evidence from observations, re-analyses and climate models that the AMOC decline was due to the combined action of the North Atlantic Oscillation and East Atlantic Pattern, the two leading modes of North Atlantic atmospheric surface pressure variability, which prior to the decline both transitioned into their negative phases. This change in atmospheric circulation diminished oceanic heat loss over the Labrador Sea and forced ocean circulation changes lowering upper ocean salinity transport into that region. As a consequence, Labrador Sea deep convection weakened, which eventually slowed the AMOC. This study suggests a new mechanism for decadal AMOC variability, which is important to multiyear climate predictability and climate change detection in the North Atlantic sector.

Improved representations of coupled soil–canopy processes in the CABLE land surface model (Subversion revision 3432)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haverd, Vanessa; Cuntz, Matthias; Nieradzik, Lars P.

CABLE is a global land surface model, which has been used extensively in offline and coupled simulations. While CABLE performs well in comparison with other land surface models, results are impacted by decoupling of transpiration and photosynthesis fluxes under drying soil conditions, often leading to implausibly high water use efficiencies. Here, we present a solution to this problem, ensuring that modelled transpiration is always consistent with modelled photosynthesis, while introducing a parsimonious single-parameter drought response function which is coupled to root water uptake. We further improve CABLE's simulation of coupled soil–canopy processes by introducing an alternative hydrology model with amore » physically accurate representation of coupled energy and water fluxes at the soil–air interface, including a more realistic formulation of transfer under atmospherically stable conditions within the canopy and in the presence of leaf litter. The effects of these model developments are assessed using data from 18 stations from the global eddy covariance FLUXNET database, selected to span a large climatic range. Here, marked improvements are demonstrated, with root mean squared errors for monthly latent heat fluxes and water use efficiencies being reduced by 40 %. Results highlight the important roles of deep soil moisture in mediating drought response and litter in dampening soil evaporation.« less

Improved representations of coupled soil-canopy processes in the CABLE land surface model (Subversion revision 3432)

NASA Astrophysics Data System (ADS)

Haverd, Vanessa; Cuntz, Matthias; Nieradzik, Lars P.; Harman, Ian N.

2016-09-01

CABLE is a global land surface model, which has been used extensively in offline and coupled simulations. While CABLE performs well in comparison with other land surface models, results are impacted by decoupling of transpiration and photosynthesis fluxes under drying soil conditions, often leading to implausibly high water use efficiencies. Here, we present a solution to this problem, ensuring that modelled transpiration is always consistent with modelled photosynthesis, while introducing a parsimonious single-parameter drought response function which is coupled to root water uptake. We further improve CABLE's simulation of coupled soil-canopy processes by introducing an alternative hydrology model with a physically accurate representation of coupled energy and water fluxes at the soil-air interface, including a more realistic formulation of transfer under atmospherically stable conditions within the canopy and in the presence of leaf litter. The effects of these model developments are assessed using data from 18 stations from the global eddy covariance FLUXNET database, selected to span a large climatic range. Marked improvements are demonstrated, with root mean squared errors for monthly latent heat fluxes and water use efficiencies being reduced by 40 %. Results highlight the important roles of deep soil moisture in mediating drought response and litter in dampening soil evaporation.

The Influence of Green Surface Modification of Oil Palm Mesocarp Fiber by Superheated Steam on the Mechanical Properties and Dimensional Stability of Oil Palm Mesocarp Fiber/Poly(butylene succinate) Biocomposite

PubMed Central

Then, Yoon Yee; Ibrahim, Nor Azowa; Zainuddin, Norhazlin; Ariffin, Hidayah; Yunus, Wan Md Zin Wan; Chieng, Buong Woei

2014-01-01

In this paper, superheated steam (SHS) was used as cost effective and green processing technique to modify oil palm mesocarp fiber (OPMF) for biocomposite applications. The purpose of this modification was to promote the adhesion between fiber and thermoplastic. The modification was carried out in a SHS oven at various temperature (200–230 °C) and time (30–120 min) under normal atmospheric pressure. The biocomposites from SHS-treated OPMFs and poly(butylene succinate) (PBS) at a weight ratio of 70:30 were prepared by melt blending technique. The mechanical properties and dimensional stability of the biocomposites were evaluated. This study showed that the SHS treatment increased the roughness of the fiber surface due to the removal of surface impurities and hemicellulose. The tensile, flexural and impact properties, as well as dimensional stability of the biocomposites were markedly enhanced by the presence of SHS-treated OPMF. Scanning electron microscopy analysis showed improvement of interfacial adhesion between PBS and SHS-treated OPMF. This work demonstrated that SHS could be used as an eco-friendly and sustainable processing method for modification of OPMF in biocomposite fabrication. PMID:25177865

Monitoring the colonization of sugarcane and rice plants by the endophytic diazotrophic bacterium Gluconacetobacter diazotrophicus marked with gfp and gusA reporter genes.

PubMed

Rouws, L F M; Meneses, C H S G; Guedes, H V; Vidal, M S; Baldani, J I; Schwab, S

2010-09-01

To evaluate the colonization process of sugarcane plantlets and hydroponically grown rice seedlings by Gluconacetobacter diazotrophicus strain PAL5 marked with the gusA and gfp reporter genes. Sugarcane plantlets inoculated in vitro with PAL5 carrying the gfp::gusA plasmid pHRGFPGUS did not present green fluorescence, but beta-glucuronidase (GUS)-stained bacteria could be observed inside sugarcane roots. To complement this existing inoculation methodology for micropropagated sugarcane with a more rapid colonization assay, we employed hydroponically grown gnotobiotic rice seedlings to study PAL5-plant interaction. PAL5 could be isolated from the root surface (10(8) CFU g(-1)) and from surface-disinfected root and stem tissues (10(4) CFU g(-1)) of inoculated plants, suggesting that PAL5 colonized the internal plant tissues. Light microscopy confirmed the presence of bacteria inside the root tissue. After inoculation of rice plantlets with PAL5 marked with the gfp plasmid pHRGFPTC, bright green fluorescent bacteria could be seen colonizing the rice root surface, mainly at the sites of lateral root emergence, at root caps and on root hairs. The plasmids pHRGFPGUS and pHRGFPTC are valid tools to mark PAL5 and monitor the colonization of micropropagated sugarcane and hydroponic rice seedlings. These tools are of use to: (i) study PAL5 mutants affected in bacteria-plant interactions, (ii) monitor plant colonization in real time and (iii) distinguish PAL5 from other bacteria during the study of mixed inoculants.

IL-17A promotes protective IgA responses and expression of other potential effectors against the lumen-dwelling enteric parasite Giardia.

PubMed

Dann, Sara M; Manthey, Carolin F; Le, Christine; Miyamoto, Yukiko; Gima, Lauren; Abrahim, Andrew; Cao, Anthony T; Hanson, Elaine M; Kolls, Jay K; Raz, Eyal; Cong, Yingzi; Eckmann, Lars

2015-09-01

Giardia lamblia is a leading protozoan cause of diarrheal disease worldwide. It colonizes the lumen and epithelial surface of the small intestine, but does not invade the mucosa. Acute infection causes only minimal mucosal inflammation. Effective immune defenses exist, yet their identity and mechanisms remain incompletely understood. Interleukin (IL)-17A has emerged as an important cytokine involved in inflammation and antimicrobial defense against bacterial pathogens at mucosal surfaces. In this study, we demonstrate that IL-17A has a crucial function in host defense against Giardia infection. Using murine infection models with G. muris and G. lamblia, we observed marked and selective induction of intestinal IL-17A with peak expression after 2 weeks. Th17 cells in the lamina propria and innate immune cells in the epithelial compartment of the small intestine were responsible for the IL-17A response. Experiments in gene-targeted mice revealed that the cytokine, and its cognate receptor IL-17RA, were required for eradication of the parasite. The actions of the cytokine were mediated by hematopoietic cells, and were required for the transport of IgA into the intestinal lumen, since IL-17A deficiency led to marked reduction of fecal IgA levels, as well as for increased intestinal expression of several other potential effectors, including β-defensin 1 and resistin-like molecule β. In contrast, intestinal hypermotility, another major antigiardial defense mechanism, was not impacted by IL-17A loss. Taken together, these findings demonstrate that IL-17A and IL-17 receptor signaling are essential for intestinal defense against the important lumen-dwelling intestinal parasite Giardia. Copyright © 2015 Elsevier Inc. All rights reserved.

Fission Surface Power Technology Demonstration Unit

NASA Image and Video Library

2016-11-09

NASA Glenn Technician Mark Springowski works on a 10-kilowatt Stirling Power Conversion Unit, which is part of the Fission Surface Power Technology Demonstration Unit. This is a system level demonstration of a surface power system, which could potentially be used to support manned missions to the moon or Mars. A flight system would use 180 kilowatt nuclear fission reactor and four Stirling PCU’s to produce 40 kW of electricity for manned surface missions.

A closer look at water-related geologic activity on Mars

USGS Publications Warehouse

McEwen, A.S.; Hansen, C.J.; Delamere, W.A.; Eliason, E.M.; Herkenhoff, K. E.; Keszthelyi, L.; Gulick, V.C.; Kirk, R.L.; Mellon, M.T.; Grant, J. A.; Thomas, N.; Weitz, C.M.; Squyres, S. W.; Bridges, N.T.; Murchie, S.L.; Seelos, F.; Seelos, K.; Okubo, C.H.; Milazzo, M.P.; Tornabene, L.L.; Jaeger, W.L.; Byrne, S.; Russell, P.S.; Griffes, J.L.; Martinez-Alonso, S.; Davatzes, A.; Chuang, F.C.; Thomson, B.J.; Fishbaugh, K.E.; Dundas, C.M.; Kolb, K.J.; Banks, M.E.; Wray, J.J.

2007-01-01

Water has supposedly marked the surface of Mars and produced characteristic landforms. To understand the history of water on Mars, we take a close look at key locations with the High-Resolution Imaging Science Experiment on board the Mars Reconnaissance Orbiter, reaching fine spatial scales of 25 to 32 centimeters per pixel. Boulders ranging up to ???2 meters in diameter are ubiquitous in the middle to high latitudes, which include deposits previously interpreted as fine-grained ocean sediments or dusty snow. Bright gully deposits identify six locations with very recent activity, but these lie on steep (20?? to 35??) slopes where dry mass wasting could occur. Thus, we cannot confirm the reality of ancient oceans or water in active gullies but do see evidence of fluvial modification of geologically recent mid-latitude gullies and equatorial impact craters.

Microscopic analysis and simulation of check-mark stain on the galvanized steel strip

NASA Astrophysics Data System (ADS)

So, Hongyun; Yoon, Hyun Gi; Chung, Myung Kyoon

2010-11-01

When galvanized steel strip is produced through a continuous hot-dip galvanizing process, the thickness of adhered zinc film is controlled by plane impinging air gas jet referred to as "air-knife system". In such a gas-jet wiping process, stain of check-mark or sag line shape frequently appears. The check-mark defect is caused by non-uniform zinc coating and the oblique patterns such as "W", "V" or "X" on the coated surface. The present paper presents a cause and analysis of the check-mark formation and a numerical simulation of sag lines by using the numerical data produced by Large Eddy Simulation (LES) of the three-dimensional compressible turbulent flow field around the air-knife system. It was found that there is alternating plane-wise vortices near the impinging stagnation region and such alternating vortices move almost periodically to the right and to the left sides on the stagnation line due to the jet flow instability. Meanwhile, in order to simulate the check-mark formation, a novel perturbation model has been developed to predict the variation of coating thickness along the transverse direction. Finally, the three-dimensional zinc coating surface was obtained by the present perturbation model. It was found that the sag line formation is determined by the combination of the instantaneous coating thickness distribution along the transverse direction near the stagnation line and the feed speed of the steel strip.

Controlled nanostructrures formation by ultra fast laser pulses for color marking.

PubMed

Dusser, B; Sagan, Z; Soder, H; Faure, N; Colombier, J P; Jourlin, M; Audouard, E

2010-02-01

Precise nanostructuration of surface and the subsequent upgrades in material properties is a strong outcome of ultra fast laser irradiations. Material characteristics can be designed on mesoscopic scales, carrying new optical properties. We demonstrate in this work, the possibility of achieving material modifications using ultra short pulses, via polarization dependent structures generation, that can generate specific color patterns. These oriented nanostructures created on the metal surface, called ripples, are typically smaller than the laser wavelength and in the range of visible spectrum. In this way, a complex colorization process of the material, involving imprinting, calibration and reading, has been performed to associate a priori defined colors. This new method based on the control of the laser-driven nanostructure orientation allows cumulating high quantity of information in a minimal surface, proposing new applications for laser marking and new types of identifying codes.

Salinization owing to evaporation from bare-soil surfaces and its influences on the evaporation

NASA Astrophysics Data System (ADS)

Shimojimaa, Eiichi; Yoshioka, Ryuma; Tamagawa, Ichiro

1996-04-01

To investigate the relationship between evaporation and salinization, the surfaces of three columns of uniform porous materials, desert dune sand, silica sand and glass beads, respectively, were exposed to a temperature-, humidity- and/or wind-speed-controlled ambient atmosphere. For the dune sand, chemicals such as Na +, Ca 2+, Cl - and SO 42-, dissolved mainly from CaSO 4, Na 2SO 4, CaCO 3 and NaC1 in the sand particles, caused marked salinization near the top surface. Slow dissolution of Na 2SO 4 and CaSO 4 influenced the development of concentration profiles for SO 42- and Na + markedly for months after the beginning of the experiment, while the profile of Cl - was not affected directly, because dissolution of NaCl was rapid. Concentration profiles of Cl - for the glass beads and for the silica sand columns filled with a high concentration of NaCI solution of (10 4 mg1 -1 for Cl -), were analysed similarly. Experimental results suggested that the vapour flux in a dry soil became larger because of the increase in the gradient of the vapour density caused by greater chemical enrichment near the top surface compared with that at the evaporation surface. The vapour flux also became smaller as the gradient of the vapour density decreased, owing to the markedly enriched evaporation surface. In the experiment with glass beads, filled with the NaCl solution, solute crystallization (4-10 mm thick) was observed. For the dune sand, only when a turbulent airflow was applied did a crust (a few millimetres in thickness) form entirely on the top surface. Such deposition led to a reduction in the flux of water vapour as the permeable cross-sectional area decreased. The resistance to transfer increased three to ten times for the glass beads but only by 30% for the dune sand. The lower increase for the dune sand may be due to penetration of the applied airflow into cracks in the crust.

Assessment of surface relief and short cracks under cyclic creep in a type 316LN austenitic stainless steel

NASA Astrophysics Data System (ADS)

Sarkar, Aritra; Nagesha, A.; Parameswaran, P.; Sandhya, R.; Laha, K.

2015-12-01

Formation of surface relief and short cracks under cyclic creep (stress-controlled fatigue) in type 316LN stainless steel was studied at temperatures ranging from ambient to 923 K using scanning electron microscopy technique. The surface topography and crack distribution behaviour under cyclic creep were found to be strong functions of testing temperature due to the difference in strain accumulation. At 823 K, surface relief mainly consisted of fine slip markings due to negligible accumulation of strain as a consequence of dynamic strain ageing (DSA) which led to an increase in the cyclic life. Persistent slip markings (PSM) with distinct extrusions containing minute cracks were seen to prevail in the temperature range 873-923 K, indicating a higher slip activity causing higher strain accumulation in the absence of DSA. Besides, a large number of secondary cracks (both transgranular and intergranular) which were partially accentuated by severe oxidation, were observed. Extensive cavitation-induced grain boundary cracking took place at 923 K, which coalesced with PSM-induced transgranular cracks resulting in failure dominated by creep that in turn led to a drastic reduction in cyclic life. Investigations on the influence of stress rate were also carried out which underlined the presence of DSA at 823 K. At 923 K, lowering the stress rate caused further strengthening of the contribution from creep damage marked by a shift in the damage mechanism from cyclic slip to diffusion.

Global climate change driven by soot at the K-Pg boundary as the cause of the mass extinction

NASA Astrophysics Data System (ADS)

Kaiho, Kunio; Oshima, Naga; Adachi, Kouji; Adachi, Yukimasa; Mizukami, Takuya; Fujibayashi, Megumu; Saito, Ryosuke

2016-07-01

The mass extinction of life 66 million years ago at the Cretaceous/Paleogene boundary, marked by the extinctions of dinosaurs and shallow marine organisms, is important because it led to the macroevolution of mammals and appearance of humans. The current hypothesis for the extinction is that an asteroid impact in present-day Mexico formed condensed aerosols in the stratosphere, which caused the cessation of photosynthesis and global near-freezing conditions. Here, we show that the stratospheric aerosols did not induce darkness that resulted in milder cooling than previously thought. We propose a new hypothesis that latitude-dependent climate changes caused by massive stratospheric soot explain the known mortality and survival on land and in oceans at the Cretaceous/Paleogene boundary. The stratospheric soot was ejected from the oil-rich area by the asteroid impact and was spread globally. The soot aerosols caused sufficiently colder climates at mid-high latitudes and drought with milder cooling at low latitudes on land, in addition to causing limited cessation of photosynthesis in global oceans within a few months to two years after the impact, followed by surface-water cooling in global oceans in a few years. The rapid climate change induced terrestrial extinctions followed by marine extinctions over several years.

Global climate change driven by soot at the K-Pg boundary as the cause of the mass extinction

PubMed Central

Kaiho, Kunio; Oshima, Naga; Adachi, Kouji; Adachi, Yukimasa; Mizukami, Takuya; Fujibayashi, Megumu; Saito, Ryosuke

2016-01-01

The mass extinction of life 66 million years ago at the Cretaceous/Paleogene boundary, marked by the extinctions of dinosaurs and shallow marine organisms, is important because it led to the macroevolution of mammals and appearance of humans. The current hypothesis for the extinction is that an asteroid impact in present-day Mexico formed condensed aerosols in the stratosphere, which caused the cessation of photosynthesis and global near-freezing conditions. Here, we show that the stratospheric aerosols did not induce darkness that resulted in milder cooling than previously thought. We propose a new hypothesis that latitude-dependent climate changes caused by massive stratospheric soot explain the known mortality and survival on land and in oceans at the Cretaceous/Paleogene boundary. The stratospheric soot was ejected from the oil-rich area by the asteroid impact and was spread globally. The soot aerosols caused sufficiently colder climates at mid–high latitudes and drought with milder cooling at low latitudes on land, in addition to causing limited cessation of photosynthesis in global oceans within a few months to two years after the impact, followed by surface-water cooling in global oceans in a few years. The rapid climate change induced terrestrial extinctions followed by marine extinctions over several years. PMID:27414998

Developmental Effects of Ocean Acidification Conditions and Elevated Temperature on Homarus Americanus Larvae

NASA Astrophysics Data System (ADS)

Mcveigh, H.; Waller, J. D.

2016-02-01

The Gulf of Maine is experiencing a rapid warming in sea surface temperature and a marked decrease in pH. This study aimed to quantify the impact of elevated temperature and acidification on the larval development of the iconic American lobster (Homarus americanus). Experimental conditions were reflective of current and IPCC predicted levels of temperature and pCO2 to be reached by the end of the century. Larvae were measured for growth (carapace length), development time, and survivorship over the larval duration. Treatments of elevated temperatures experienced decreased development time across the larval stages of H. americanus. Consequently mortality increased at a significantly higher rate under elevated temperature. An increase in larval mortality may decrease recruitment to the commercial fishery, thus impacting the most valuable single species in the state of Maine. Furthermore, experimental pCO2 treatments yielded a significantly decreased development time between larval stages II and III, yet did not have a significant impact on carapace length or mortality. This study indicates that warmer temperatures may have a greater influence than decreased pH on larval development and survival. Determining how this species may respond to changing climactic conditions will better inform the sustainability efforts of such a critical marine fishery.

Global climate change driven by soot at the K-Pg boundary as the cause of the mass extinction.

PubMed

Kaiho, Kunio; Oshima, Naga; Adachi, Kouji; Adachi, Yukimasa; Mizukami, Takuya; Fujibayashi, Megumu; Saito, Ryosuke

2016-07-14

The mass extinction of life 66 million years ago at the Cretaceous/Paleogene boundary, marked by the extinctions of dinosaurs and shallow marine organisms, is important because it led to the macroevolution of mammals and appearance of humans. The current hypothesis for the extinction is that an asteroid impact in present-day Mexico formed condensed aerosols in the stratosphere, which caused the cessation of photosynthesis and global near-freezing conditions. Here, we show that the stratospheric aerosols did not induce darkness that resulted in milder cooling than previously thought. We propose a new hypothesis that latitude-dependent climate changes caused by massive stratospheric soot explain the known mortality and survival on land and in oceans at the Cretaceous/Paleogene boundary. The stratospheric soot was ejected from the oil-rich area by the asteroid impact and was spread globally. The soot aerosols caused sufficiently colder climates at mid-high latitudes and drought with milder cooling at low latitudes on land, in addition to causing limited cessation of photosynthesis in global oceans within a few months to two years after the impact, followed by surface-water cooling in global oceans in a few years. The rapid climate change induced terrestrial extinctions followed by marine extinctions over several years.

Contraction and Expansion of the Upper Zambezi Wetlands in Response to Precipitation Regime Changes and Impacts on Carbon, Energy and Water Fluxes

NASA Astrophysics Data System (ADS)

Lowman, L.; Barros, A. P.

2017-12-01

The Upper Zambezi River Basin (UZRB) serves as the headwater catchment of the fourth-largest river in Africa, provides essential freshwater resources to arid and semi-arid regions within its boundaries, and recharges the Northern Kalahari Aquifer. Shallow and clayey soils give way to seasonal waterlogging, especially along drainage lines, favoring the establishment of wetlands. Woodland savanna, grasslands and miombo dominate the UZRB's diverse ecosystem, marking a complex transition zone between the Congo tropical rainforest and the Kalahari Desert that reflects spatial rainfall gradients. Satellite imagery shows that permanent wetlands are located in low-lying convergence zones in the northeast and northwest corners of UZRB where surface-groundwater interactions are most vigorous. However, orographic precipitation gradients cannot fully explain interannual changes in wetland area and vegetation density. We hypothesize that changes in vegetation density result from nonlinear interactions and feedbacks among precipitation, canopy biophysical properties, soil moisture and groundwater processes modulated by topography and regional hydrogeology. This work aims to understand how changes in vegetation density, particularly in and around permanent and intermittent wetlands, impact carbon, energy and water fluxes. Using the MODIS Nadir BRDF-Adjusted Reflectance product, a seasonally-varying wetland class is derived that reflects inter-annual precipitation and groundwater variability. The Duke Coupled Hydrology Model with Prognostic Vegetation is adapted to include C4 photosynthesis for the UZRB grasslands and used to simulate changes in canopy density and impacts on gross primary productivity, evapotranspiration, and soil moisture at high spatial and temporal resolution. Initial results using the column-wise model provide a baseline for understanding surface fluxes before incorporating groundwater and subsurface flows crucial to investigating the implicit nonlinearities of the region.

Chemical enhancement of footwear impressions in blood deposited on fabric--evaluating the use of alginate casting materials followed by chemical enhancement.

PubMed

Farrugia, Kevin J; NicDaéid, Niamh; Savage, Kathleen A; Bandey, Helen

2010-12-01

Most footwear marks made in blood on a surface such as fabric tend to be enhanced in situ rather than physically recovered using a lifting technique prior to enhancement. This work reports on the use of an alginate material to recover the impressed footwear marks made in blood and deposited on a range of fabric types and colours. The lifted marks were then enhanced using acid black 1 and leuco crystal violet with excellent results. This presents a new method for the lifting and recovery of blood impressions in situ from crime scene followed by subsequent mark enhancement of the lifted impression. Copyright © 2010 Forensic Science Society. Published by Elsevier Ireland Ltd.. All rights reserved.

Trail Marking by Caterpillars of the Silverspot Butterfly Dione Juno Huascuma

PubMed Central

Pescador-Rubio, Alfonso; Stanford-Camargo, Sergio G.; Páez-Gerardo, Luis E; Ramírez-Reyes, Alberto J.; Ibarra-Jiménez, René A.; Fitzgerald, Terrence D.

2011-01-01

A pheromone is implicated in the trail marking behavior of caterpillars of the nymphalid silverspot butterfly, Dione juno huascuma (Reakirt) (Lepidoptera: Heliconiinae) that feed gregariously on Passiflora (Malpighiales: Passifloraceae) vines in Mexico. Although they mark pathways leading from one feeding site to another with silk, this study shows that the silk was neither adequate nor necessary to elicit trail following behavior. Caterpillars marked trails with a long-lived pheromone that was deposited when they brushed the ventral surfaces of the tips of their abdomens along branch pathways. The caterpillars distinguished between pathways deposited by different numbers of siblings and between trails of different ages. Caterpillars also preferentially followed the trails of conspecifics over those of another nymphalid, Nymphalis antiopa L., the mourning cloak butterfly. PMID:21861659

TES Observations of Chryse and Acidalia Planitiae: Multiple Working Hypotheses for Distributions of Surface Compositions

NASA Technical Reports Server (NTRS)

Wyatt, M. B.; Bandfield, J. L.; McSween, H. Y., Jr.; Christensen, P. R.; Moersch, J.

2002-01-01

A gradation of surface units represents either (1) an influx of basaltic sediment from southern highlands, deposited on andesitic volcanics, or (2) incompletely weathered basalt marking the geographic extent of submarine alteration of basaltic crust. Additional information is contained in the original extended abstract.

Surface preparation of pavements prior to application of pavement markings

NASA Astrophysics Data System (ADS)

Dale, J. M.

1980-01-01

A brush assembly was designed, fabricated and installed on a Texas Department of Highways and Public Transportation striping truck and run over a variety of roads. It was found that brushing did not significantly extend the service life of the traffic marking paint. There was not sufficient improvement to consider mounting brush assemblies ahead of the spray guns on striping trucks for use on a daily basis.

MENC in International Perspective: In Its First One Hundred Years, MENC Has Had an Impact on Music Education Not Only in the United States, but Globally

ERIC Educational Resources Information Center

McCarthy, Marie

2007-01-01

The year 2007 marks the centennial celebration of MENC: The National Association for Music Education. Anniversaries mark important milestones in the development of a professional association. They provide an occasion for remembering past achievements and envisioning future directions. MENC, which was initially known as Music Supervisors National…

Splashing Droplets

NASA Technical Reports Server (NTRS)

VanderWal, Randall L.; Kizito, John Patrick; Berger, Gordon M.; Iwan, J.; Alexander, D.; Tryggvason, Gretar

2002-01-01

Current data on droplet breakup is scarce for the sizes and velocities typical of practical applications such as in spray combustion processes and coating processes. While much more representative of practical applications, the small spatial scales and rapid time-scales prevent detailed measurement of the internal fluid dynamics and liquid property gradients produced by impinging upon surfaces. Realized through the extended spatial and temporal scales afforded by a microgravity environment, an improved understanding of drop breakup dynamics is sought to understand and ultimately control the impingement dynamics of droplets upon surfaces in practical situations. The primary objective of this research will be to mark the onset of different 'splashing modes' and to determine their temperature, pressure and angle dependence for impinging droplets representative of practical fluids. In addition, we are modeling the evolution of droplets that do not initially splash but rather undergo a 'fingering' evolution observed on the spreading fluid front and the transformation of these fingers into splashed products. An example of our experimental data is presented below. These images are of Isopar V impacting a mirror-polished surface. They were acquired using a high-speed camera at 1000 frames per second. They show the spreading of a single droplet after impact and ensuing finger instabilities. Normal gravity experimental data such as this will guide low gravity measurements in the 2.2 second drop tower and KC-135 aircraft as available. Presently we are in the process of comparing the experimental data of droplet shape evolution to numerical models, which can also capture the internal fluid dynamics and liquid property gradients such as produced by impingement upon a heated surface. To-date isothermal numerical data has been modeled using direct numerical simulations of representative splashing droplets. The data obtained so far indicates that the present model describes well the droplet wall interactions to a point in time just before splash. Additional information is included in the original extended abstract.

Role of the Atlantic Multidecadal Variability on extreme climate conditions over North America

NASA Astrophysics Data System (ADS)

Ruprich-Robert, Yohan; Delworth, Thomas; Msadek, Rym; Castruccio, Frederic; Yeager, Stephen; Danabasoglu, Gokhan

2017-04-01

The Atlantic Multidecadal Variability (AMV) is associated with marked modulations of climate anomalies observed over many areas of the globe like droughts, decline in sea ice or changes in the atmospheric circulation. However, the shortness of the historical observations compared to the AMV period ( 60-80yr) makes it difficult to show that the AMV is a direct driver of these variations. To isolate the AMV climate response, we use a suite of global coupled models from GFDL and NCAR, in which the North Atlantic sea surface temperatures are restored to the observed AMV pattern, while the other ocean basins are left fully coupled. In order to explore and robustly isolate the AMV impacts on extreme events, we use large ensemble simulations (between 30 and 100 members depending on the model) that are integrated for 10 years. We investigate the importance of model resolution by analyzing GFDL models that vary in their atmospheric resolution and we assess the robustness of the results by comparing them to similar experiments performed with the NCAR coupled model. Further, we investigate the influence of model surface temperature biases on the simulated AMV teleconnections using a flux-adjusted experiment based on a model configuration that corrects for momentum, enthalpy and freshwater fluxes. We focus in this presentation on the impact of the AMV on the occurrence of the North American heat waves. We find that the AMV modulates by about 30% the occurrence of heat waves over North Mexico and the South-West of USA, with more heat waves during a warm phase of the AMV. The main reason for such an increase is that, during a warm AMV phase, the anomalously warm sea surface temperature leads to an increase of the atmospheric convection over the tropical Atlantic, as well as to a an anomalous downward motion over North America. This atmospheric response to AMV inhibits the precipitation over there and drives a deficit of soil moisture. In the summer, the latent heat of evaporation usually cools the surface precluding strong surface temperature warming. But the lack of soil moisture allows less evaporation, which leads to positive surface temperature anomalies and an increase of the occurrence of heat waves. By comparing the results from all the model configurations, we highlight the importance of the representation of the soil moisture by the model on the modulation of heat waves by the AMV. We also stress the influence of model's mean state biases on the simulated AMV impacts.

Integrating Instrumental Data Provides the Full Science in 3D

NASA Astrophysics Data System (ADS)

Turrin, M.; Boghosian, A.; Bell, R. E.; Frearson, N.

2017-12-01

Looking at data sparks questions, discussion and insights. By integrating multiple data sets we deepen our understanding of how cryosphere processes operate. Field collected data provide measurements from multiple instruments supporting rapid insights. Icepod provides a platform focused on the integration of multiple instruments. Over the last three seasons, the ROSETTA-Ice project has deployed Icepod to comprehensively map the Ross Ice Shelf, Antarctica. This integrative data collection along with new methods of data visualization allows us to answer questions about ice shelf structure and evolution that arise during data processing and review. While data are vetted and archived in the field to confirm instruments are operating, upon return to the lab data are again reviewed for accuracy before full analysis. Recent review of shallow ice radar data from the Beardmore Glacier, an outlet glacier into the Ross Ice Shelf, presented an abrupt discontinuity in the ice surface. This sharp 8m surface elevation drop was originally interpreted as a processing error. Data were reexamined, integrating the simultaneously collected shallow and deep ice radar with lidar data. All the data sources showed the surface discontinuity, confirming the abrupt 8m drop in surface elevation. Examining high resolution WorldView satellite imagery revealed a persistent source for these elevation drops. The satellite imagery showed that this tear in the ice surface was only one piece of a larger pattern of "chatter marks" in ice that flows at a rate of 300 m/yr. The markings are buried over a distance of 30 km or after 100 years of travel down Beardmore Glacier towards the front of the Ross Ice Shelf. Using Icepod's lidar and cameras we map this chatter mark feature in 3D to reveal its full structure. We use digital elevation models from WorldView to map the other along flow chatter marks. In order to investigate the relationship between these surface features and basal crevasses, the deep ice radar enables a 3D model of the base of the ice shelf. Both the high resolution imagery and radar echograms along with a VR experience of our 3D models, allows viewers to fully explore the dataset and gain insight into the processes producing these features.

Effect of artificial toothbrushing and water storage on the surface roughness and micromechanical properties of tooth-colored CAD-CAM materials.

PubMed

Flury, Simon; Diebold, Elisabeth; Peutzfeldt, Anne; Lussi, Adrian

2017-06-01

Because of the different composition of resin-ceramic computer-aided design and computer-aided manufacturing (CAD-CAM) materials, their polishability and their micromechanical properties vary. Moreover, depending on the composition of the materials, their surface roughness and micromechanical properties are likely to change with time. The purpose of this in vitro study was to investigate the effect of artificial toothbrushing and water storage on the surface roughness (Ra and Rz) and the micromechanical properties, surface hardness (Vickers [VHN]) and indentation modulus (E IT ), of 5 different tooth-colored CAD-CAM materials when polished with 2 different polishing systems. Specimens (n=40 per material) were cut from a composite resin (Paradigm MZ100; 3M ESPE), a feldspathic ceramic (Vitablocs Mark II; Vita Zahnfabrik), a resin nanoceramic (Lava Ultimate; 3M ESPE), a hybrid dental ceramic (Vita Enamic; Vita Zahnfabrik), and a nanocomposite resin (Ambarino High-Class; Creamed). All specimens were roughened in a standardized manner and polished either with Sof-Lex XT discs or the Vita Polishing Set Clinical. Surface roughness, VHN, and E IT were measured after polishing and after storage for 6 months (tap water, 37°C) with periodic, artificial toothbrushing. The surface roughness, VHN, and E IT results were analyzed with a nonparametric ANOVA followed by Kruskal-Wallis and exact Wilcoxon rank sum tests (α=.05). Irrespective of polishing system and of artificial toothbrushing and storage, Lava Ultimate generally showed the lowest surface roughness and Vitablocs Mark II the highest. As regards micromechanical properties, the following ranking of the CAD-CAM materials was found (from highest VHN/E IT to lowest VHN/E IT ): Vitablocs Mark II > Vita Enamic > Paradigm MZ100 > Lava Ultimate > Ambarino High-Class. Irrespective of material and of artificial toothbrushing and storage, polishing with Sof-Lex XT discs resulted in lower surface roughness than the Vita Polishing Set Clinical (P≤.016). However, the polishing system generally had no influence on the micromechanical properties (P>.05). The effect of artificial toothbrushing and storage on surface roughness depended on the material and the polishing system: Ambarino High-Class was most sensitive to storage, Lava Ultimate and Vita Enamic were least sensitive. Artificial toothbrushing and storage generally resulted in a decrease in VHN and E IT for Paradigm MZ100, Lava Ultimate, and Ambarino High-Class but not for Vita Enamic and Vitablocs Mark II. Tooth-colored CAD-CAM materials with lower VHN and E IT generally showed better polishability. However, these materials were more prone to degradation by artificial toothbrushing and water storage than materials with higher VHN and E IT . Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Droplet impact on soft viscoelastic surfaces.

PubMed

Chen, Longquan; Bonaccurso, Elmar; Deng, Peigang; Zhang, Haibo

2016-12-01

In this work, we experimentally investigate the impact of water droplets onto soft viscoelastic surfaces with a wide range of impact velocities. Several impact phenomena, which depend on the dynamic interaction between the droplets and viscoelastic surfaces, have been identified and analyzed. At low We, complete rebound is observed when the impact velocity is between a lower and an upper threshold, beyond which droplets are deposited on the surface after impact. At intermediate We, entrapment of an air bubble inside the impinging droplets is found on soft surfaces, while a bubble entrapment on the surface is observed on rigid surfaces. At high We, partial rebound is only identified on the most rigid surface at We≳92. Rebounding droplets behave similarly to elastic drops rebounding on superhydrophobic surfaces and the impact process is independent of surface viscoelasticity. Further, surface viscoelasticity does not influence drop spreading after impact-as the surfaces behave like rigid surfaces-but it does affect drop recoiling. Also, the postimpact drop oscillation on soft viscoelastic surfaces is influenced by dynamic wettability of these surfaces. Comparing sessile drop oscillation with a damped harmonic oscillator allows us to conclude that surface viscoelasticity affects the damping coefficient and liquid surface tension sets the spring constant of the system.

[Cleaning and disinfection of surfaces in hospitals: Data on structure, process and result in the Frankfurt/Main Metropolitan Area].

PubMed

Hausemann, A; Hofmann, H; Otto, U; Heudorf, Ursel

2015-06-01

In addition to hand hygiene and reprocessing of medical products, cleaning and disinfection of surfaces is also an important issue in the prevention of germ transmission and by implication infections. Therefore, in 2014, the quality of the structure, process and result of surface preparation of all hospitals in Frankfurt am Main, Germany, was monitored. All 17 hospitals transferred information on the quality of structure. Process quality was obtained through direct observation during cleaning and disinfection of rooms and their plumbing units. Result quality was gained using the fluorescent method, i.e. marking surfaces with a fluorescent liquid and testing if this mark has been sufficiently removed by cleaning. Structure quality: in all hospitals the employees were trained regularly. In 12 of them, the foremen had the required qualifications, in 6 hospitals unclarity as to the intersection of the cleaning and care services remained. In 14 hospitals only visible contamination was cleaned on the weekends, whereas complete cleaning was reported to take place in 12 hospitals on Saturdays and in 2 hospitals on Sundays. The contractually stipulated cleaning (observations specified in brackets) averaged 178 m(2)/h (148 m(2)/h) per patient room and 69 m(2)/h (33 m(2)/h) for bathrooms. Process quality: during process monitoring, various hand contact surfaces were prepared insufficiently. Result quality: 63 % of fluorescent markings were appropriately removed. The need for improvement is given especially in the area of the qualification of the foremen and a in a clear definition of the intersection between cleaning and care services, as well as in the regulations for weekends and public holidays.

Applicability of Unmanned Aerial Vehicles in Research on Aeolian Processes

NASA Astrophysics Data System (ADS)

Algimantas, Česnulevičius; Artūras, Bautrėnas; Linas, Bevainis; Donatas, Ovodas; Kęstutis, Papšys

2018-02-01

Surface dynamics and instabilities are characteristic of aeolian formation. The method of surface comparison is regarded as the most appropriate one for evaluation of the intensity of aeolian processes and the amount of transported sand. The data for surface comparison can be collected by topographic survey measurements and using unmanned aerial vehicles. Time cost for relief microform fixation and measurement executing topographic survey are very high. The method of unmanned aircraft aerial photographs fixation also encounters difficulties because there are no stable clear objects and contours that enable to link aerial photographs, to determine the boundaries of captured territory and to ensure the accuracy of surface measurements. Creation of stationary anchor points is irrational due to intense sand accumulation and deflation in different climate seasons. In September 2015 and in April 2016 the combined methodology was applied for evaluation of intensity of aeolian processes in the Curonian Spit. Temporary signs (marks) were installed on the surface, coordinates of the marks were fixed using GPS and then flight of unmanned aircraft was conducted. The fixed coordinates of marks ensure the accuracy of measuring aerial imagery and the ability to calculate the possible corrections. This method was used to track and measure very small (micro-rank) relief forms (5-10 cm height and 10-20 cm length). Using this method morphometric indicators of micro-terraces caused by sand dunes pressure to gytia layer were measured in a non-contact way. An additional advantage of the method is the ability to accurately link the repeated measurements. The comparison of 3D terrain models showed sand deflation and accumulation areas and quantitative changes in the terrain very clearly.

Impact craters at falling of large asteroids in Ukraine

NASA Astrophysics Data System (ADS)

Vidmachenko, A. P.

2016-05-01

Catastrophes of different scale that are associated with the fall of celestial bodies to the Earth - occurred repeatedly in its history. But direct evidence of such catastrophes has been discovered recently. Thus, in the late 1970s studies of terrestrial rocks showed that in layers of the earth's crust that corresponded to the period of 65 million years before the present, marked by the mass extinction of some species of living creatures, and the beginning of the rapid development of others. It was then - a large body crashed to Earth in the Gulf of Mexico in Central America. The consequence of this is the Chicxulub crater with a diameter of ~170 km on Yucatan Peninsula. Modern Earth's surface retains many traces of collisions with large cosmic bodies. To indicate the craters with a diameter of more than 2 km using the name "astrobleme". Today, it found more than 230. The largest astroblems sizes exceeding 200 km. Ukraine also has some own astroblems. In Ukraine, been found nine large impact craters. Ukrainian crystalline shield, because of its stability for a long time (more than 1.5 billion years), has the highest density of large astroblems on the Earth's surface. The largest of the Ukrainian astroblems is Manevytska. It has a diameter of 45 km. There are also Ilyinetskyi (7 km), Boltysh (25 km), Obolon' (20 km), Ternivka (12-15 km), Bilylivskyi (6 km), Rotmystrivka (3 km) craters. Zelenohayska astrobleme founded near the village Zelenyi Gay in Kirovograd region and consists of two craters: larger with diameter 2.5-3.5 km and smaller - with diameter of 800 m. The presence of graphite, which was the basis for the research of the impact diamond in astroblems of this region. As a result, the diamonds have been found in rocks of Ilyinetskyi crater; later it have been found in rocks in the Bilylivska, Obolon' and other impact structures. The most detailed was studied the geological structure and the presence of diamonds in Bilylivska astrobleme

Protein Corona Formation on Colloidal Polymeric Nanoparticles and Polymeric Nanogels: Impact on Cellular Uptake, Toxicity, Immunogenicity, and Drug Release Properties.

PubMed

Obst, Katja; Yealland, Guy; Balzus, Benjamin; Miceli, Enrico; Dimde, Mathias; Weise, Christoph; Eravci, Murat; Bodmeier, Roland; Haag, Rainer; Calderón, Marcelo; Charbaji, Nada; Hedtrich, Sarah

2017-06-12

The adsorption of biomolecules to the surface of nanoparticles (NPs) following administration into biological environments is widely recognized. In particular, the "protein corona" is well understood in terms of formation kinetics and impact upon the biological interactions of NPs. Its presence is an essential consideration in the design of therapeutic NPs. In the present study, the protein coronas of six polymeric nanoparticles of prospective therapeutic use were investigated. These included three colloidal NPs-soft core-multishell (CMS) NPs, plus solid cationic Eudragit RS (EGRS), and anionic ethyl cellulose (EC) nanoparticles-and three nanogels (NGs)-thermoresponsive dendritic-polyglycerol (dPG) nanogels (NGs) and two amino-functionalized dPG-NGs. Following incubation with human plasma, protein coronas were characterized and their biological interactions compared with pristine NPs. All NPs demonstrated protein adsorption and increased hydrodynamic diameters, although the solid EGRS and EC NPs bound notably more protein than the other tested particles. Shifts toward moderately negative surface charges were also observed for all corona bearing NPs, despite varied zeta potentials in their pristine states. While the uptake and cellular adhesion of the colloidal NPs in primary human keratinocytes and human umbilical vein endothelial cells were significantly decreased when bearing the protein corona, no obvious impact was seen in the NGs. By contrast, corona bearing NGs induced marked increases in cytokine release from primary human macrophages not seen with corona bearing colloidal NPs. Despite this, no apparent enhancement to in vitro toxicity was noted. Finally, drug release from EGRS and EC NPs was assessed, where a decrease was seen in the EGRS NPs alone. Together these results provide a direct comparison of the physical and biological impact the protein corona has on NPs of widely varied character and in particular highlights a distinction between the corona's effects on NGs and colloidal NPs.

A systematical analysis of in vivo contact forces on virtual catheter tip/tissue surface contact during cardiac mapping and intervention.

PubMed

Okumura, Yasuo; Johnson, Susan B; Bunch, T Jared; Henz, Benhur D; O'Brien, Christine J; Packer, Douglas L

2008-06-01

While catheter tip/tissue contact has been shown to be an important determinant of ablative lesions in in vitro studies, the impact of contact on the outcomes of mapping and ablation in the intact heart has not been evaluated. Twelve dogs underwent atrial ablation guided by the Senesitrade mark robotic catheter remote control system. After intracardiac ultrasound (ICE) validation of contact force measured by an in-line mechanical sensor, the relationship between contact force and individual lesion formation was established during irrigated-tipped ablation (flow 17 mL/sec) at 15 watts for 30 seconds. Minimal contact by ICE correlated with force of 4.7 +/- 5.8 grams, consistent contact 9.9 +/- 8.6 grams and tissue tenting produced 25.0 +/- 14.0 grams. Conversely, catheter tip/tissue contact by ICE was predicted by contact force. A contact force of 10-20 and > or =20 grams generated full-thickness, larger volume ablative lesions than that created with <10 grams (98 +/- 69 and 89 +/- 70 mm(3) vs 40 +/- 42 mm(3), P < 0.05). Moderate (10 grams) and marked contact (15-20 grams) application produced 1.5 X greater electroanatomic map volumes that were seen with minimal contact (5 grams) (26 +/- 3 cm(3) vs 33 +/- 6, 39 +/- 3 cm(3), P < 0.05). The electroanatomic map/CT merge process was also more distorted when mapping was generated at moderate to marked contact force. This study shows that mapping and ablation using a robotic sheath guidance system are critically dependent on generated force. These findings suggest that ablative lesion size is optimized by the application of 10-20 grams of contact force, although mapping requires lower-force application to avoid image distortions.

The Selective Impact of Skinner's "Verbal Behavior" on Empirical Research: A Reply to Schlinger (2008)

ERIC Educational Resources Information Center

Dymond, Simon; Alonso-Alvarez, Benigno

2010-01-01

In a recent article, Schlinger (2008) marked the 50th anniversary of the publication of Skinner's "Verbal Behavior" (1957) by considering its impact on the field of behaviorism and research on verbal behavior. In the present article, we comment on Schlinger's conclusions regarding the impact of the book and highlight the extensions and…

77 FR 35471 - National Environmental Policy Act Implementation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-13

... designed to promote transportation safety, security, accessibility, communication or operational efficiency... surface treatments or pavement markings, small passenger shelters, railroad warning devices, train control...

Automatic extraction of road features in urban environments using dense ALS data

NASA Astrophysics Data System (ADS)

Soilán, Mario; Truong-Hong, Linh; Riveiro, Belén; Laefer, Debra

2018-02-01

This paper describes a methodology that automatically extracts semantic information from urban ALS data for urban parameterization and road network definition. First, building façades are segmented from the ground surface by combining knowledge-based information with both voxel and raster data. Next, heuristic rules and unsupervised learning are applied to the ground surface data to distinguish sidewalk and pavement points as a means for curb detection. Then radiometric information was employed for road marking extraction. Using high-density ALS data from Dublin, Ireland, this fully automatic workflow was able to generate a F-score close to 95% for pavement and sidewalk identification with a resolution of 20 cm and better than 80% for road marking detection.

Practical Guide for Flame Bending of Pipe

DTIC Science & Technology

1991-08-01

cleaned. This surface inspection should be in the form of either a dye penetrant or magnetic particle inspection depending on the base material type...fairly accurate and marked on the pipe with a permanent marks-a-lot black ink pen, chalk, soapstone , or other marker which endures flame temperatures...orifice tip. The area to be heated was Magnetic Particle (MT) Inspected any heating and after the final heat. The MT inspectionssatisfactory. prior to Were

Directional motion of impacting drops on dual-textured surfaces.

PubMed

Vaikuntanathan, V; Sivakumar, D

2012-09-01

In this work, we analyze the directional movement of impacting liquid drops on dual-textured solid surfaces comprising two different surface morphologies: a textured surface and a smooth surface. The dynamics of liquid drops impacting onto the junction line between the two parts of the dual-textured surfaces is studied experimentally for varying drop impact velocity. The dual-textured surfaces used here featured a variation in their textures' geometrical parameters as well as their surface chemistry. Two types of liquid drop differing in their surface tension were used. The impact process develops a net horizontal drop velocity towards the higher-wettability surface portion and results in a bulk movement of the impacting drop liquid. The final distance moved by the impacting drop from the junction line decreases with increasing impacting drop Weber number We. A fully theoretical model, employing a balance of forces acting at the drop contact line as well as energy conservation, is formulated to determine the variation, with We, of net horizontal drop velocity and subsequent movement of the impacting drop on the dual-textured surfaces.

Progressing quality control in environmental impact assessment beyond legislative compliance: An evaluation of the IEMA EIA Quality Mark certification scheme

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bond, Alan, E-mail: alan.bond@uea.ac.uk; Research Unit for Environmental Sciences and Management, North-West University; Fischer, Thomas B, E-mail: fischer@liverpool.ac.uk

The effectiveness of Environmental Impact Assessment (EIA) systems is contingent on a number of control mechanisms: procedural; judicial; evaluative; public and government agency; professional; and development aid agency. If we assume that procedural and judicial controls are guaranteed in developed EIA systems, then progressing effectiveness towards an acceptable level depends on improving the performance of other control mechanisms over time. These other control mechanisms are either absent, or are typically centrally controlled, requiring public finances; this we argue is an unpopular model in times of greater Government austerity. Here we evaluate a market-based mechanism for improving the performance of evaluativemore » and professional control mechanisms, the UK Institute of Environmental Management and Assessments' EIA Quality Mark. We do this by defining dimensions of effectiveness for the purposes of our evaluation, and by identifying international examples of the approaches taken to delivering the other control measures to validate the approach taken in the EIA Quality Mark. We then evaluate the EIA Quality Mark, when used in combination with legal procedures and an active judiciary, against the effectiveness dimensions and use time-series analysis of registrant data to examine its ability to progress practice. We conclude that the EIA Quality Mark has merit as a model for a market-based mechanism, and may prove a more financially palatable approach for delivering effective EIA in mature systems in countries that lack centralised agency oversight. It may, therefore, be of particular interest to some Member States of the European Union for ensuring forthcoming certification requirements stemming from recent amendments to the EIA Directive. - Highlights: • Quality control mechanisms in EIA are identified. • Effectiveness of EIA is conceptualised for evaluation purposes. • The UK IEMA EIA Quality Mark is introduced as a market-based mechanism. • The EIA Quality Mark is found to progress quality in many, but not all, areas.« less

78 FR 16198 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-14

... determine if wires touch the upper surface of the center upper auxiliary fuel tank, and marking the location, as necessary; inspecting all wire bundles above the center upper auxiliary fuel tank for splices and... requires inspecting to determine if wires touch the upper surface of the center upper auxiliary fuel tank...

Biofilm adaptation to iron availability in the presence of biotite and consequences for chemical weathering

USDA-ARS?s Scientific Manuscript database

Bacteria in nature often live within biofilms, exopolymeric matrices that provide a favorable environment that can differ markedly from their surroundings. Biofilms have been found growing on mineral surfaces and are expected to play a role in weathering those surfaces, but this role is not well und...

ESCA study of oxidation and hot corrosion of nickel-base superalloys. [Electron Spectroscopy for Chemical Analysis

NASA Technical Reports Server (NTRS)

Smith, S. R.; Carter, W. J., III; Mateescu, G. D.; Kohl, F. J.; Fryburg, G. C.; Stearns, C. A.

1980-01-01

A study of the high-temperature oxidation and Na2SO4-induced hot corrosion of nickel-base superalloys has been accomplished by using ESCA to determine the surface composition of the oxidized or corroded samples. Oxidation was carried out at 900 or 1000 C in slowly flowing O2 for samples of B-1900, NASA-TRW VIA, 713C, and IN-738. Hot corrosion of B-1900 was induced by applying a coating of Na2SO4 to preoxidized samples, then heating to 900 C in slowly flowing O2. For oxidized samples, the predominant type of scale formed by each superalloy showed a marked surface enrichment of Ti. For corroded samples, the transfer of significant amounts of material from the oxide layer to the surface of the salt layer was observed before the onset of rapidly accelerating weight gain. Marked changes in surface composition coincided with the beginning of accelerating corrosion, the most striking of which were a tenfold decrease in the sulfur to sodium ratio and an increase in the Cr(VI) to Cr(III) ratio.

Measurement of Interfacial Profiles of Wavy Film Flow on Inclined Wall

NASA Astrophysics Data System (ADS)

Rosli, N.; Amagai, K.

2016-02-01

Falling liquid films on inclined wall present in many industrial processes such as in food processing, seawater desalination and electronic devices manufacturing industries. In order to ensure an optimal efficiency of the operation in these industries, a fundamental study on the interfacial flow profiles of the liquid film is of great importance. However, it is generally difficult to experimentally predict the interfacial profiles of liquid film flow on inclined wall due to the instable wavy flow that usually formed on the liquid film surface. In this paper, the liquid film surface velocity was measured by using a non-intrusive technique called as photochromic dye marking method. This technique utilizes the color change of liquid containing the photochromic dye when exposed to the UV light source. The movement of liquid film surface marked by the UV light was analyzed together with the wave passing over the liquid. As a result, the liquid film surface was found to slightly shrink its gradual movement when approached by the wave before gradually move again after the intersection with the wave.

Restoration of obliterated engraved marks on steel surfaces by chemical etching reagent.

PubMed

Song, Qingfang

2015-05-01

Chemical etching technique is widely used for restoration of obliterated engraved marks on steel surface in the field of public security. The consumed thickness of steel surface during restoration process is considered as a major criterion for evaluating the efficiency of the chemical etching reagent. The thinner the consumed thickness, the higher the restoration efficiency. According to chemical principles, maintaining the continuous oxidative capabilities of etching reagents and increasing the kinetic rate difference of the reaction between the engraved and non-engraved area with the chemical etching reagent can effectively reduce the consumed steel thickness. The study employed steel surface from the engine case of motorcycle and the car frame of automobile. The chemical etching reagents are composed of nitric acid as the oxidizer, hydrofluoric acid as the coordination agent and mixed with glacial acetic acid or acetone as the solvents. Based on the performance evaluation of three different etching reagents, the one composed of HNO3, HF and acetone gave the best result. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Larval Settlement: The Role of Surface Topography for Sessile Coral Reef Invertebrates

PubMed Central

Whalan, Steve; Abdul Wahab, Muhammad A.; Sprungala, Susanne; Poole, Andrew J.; de Nys, Rocky

2015-01-01

For sessile marine invertebrates with complex life cycles, habitat choice is directed by the larval phase. Defining which habitat-linked cues are implicated in sessile invertebrate larval settlement has largely concentrated on chemical cues which are thought to signal optimal habitat. There has been less effort establishing physical settlement cues, including the role of surface microtopography. This laboratory based study tested whether surface microtopography alone (without chemical cues) plays an important contributing role in the settlement of larvae of coral reef sessile invertebrates. We measured settlement to tiles, engineered with surface microtopography (holes) that closely matched the sizes (width) of larvae of a range of corals and sponges, in addition to surfaces with holes that were markedly larger than larvae. Larvae from two species of scleractinian corals (Acropora millepora and Ctenactis crassa) and three species of coral reef sponges (Luffariella variabilis, Carteriospongia foliascens and Ircinia sp.,) were used in experiments. L. variabilis, A. millepora and C. crassa showed markedly higher settlement to surface microtopography that closely matched their larval width. C. foliascens and Ircinia sp., showed no specificity to surface microtopography, settling just as often to microtopography as to flat surfaces. The findings of this study question the sole reliance on chemical based larval settlement cues, previously established for some coral and sponge species, and demonstrate that specific physical cues (surface complexity) can also play an important role in larval settlement of coral reef sessile invertebrates. PMID:25671562

Larval settlement: the role of surface topography for sessile coral reef invertebrates.

PubMed

Whalan, Steve; Wahab, Muhammad A Abdul; Sprungala, Susanne; Poole, Andrew J; de Nys, Rocky

2015-01-01

For sessile marine invertebrates with complex life cycles, habitat choice is directed by the larval phase. Defining which habitat-linked cues are implicated in sessile invertebrate larval settlement has largely concentrated on chemical cues which are thought to signal optimal habitat. There has been less effort establishing physical settlement cues, including the role of surface microtopography. This laboratory based study tested whether surface microtopography alone (without chemical cues) plays an important contributing role in the settlement of larvae of coral reef sessile invertebrates. We measured settlement to tiles, engineered with surface microtopography (holes) that closely matched the sizes (width) of larvae of a range of corals and sponges, in addition to surfaces with holes that were markedly larger than larvae. Larvae from two species of scleractinian corals (Acropora millepora and Ctenactis crassa) and three species of coral reef sponges (Luffariella variabilis, Carteriospongia foliascens and Ircinia sp.,) were used in experiments. L. variabilis, A. millepora and C. crassa showed markedly higher settlement to surface microtopography that closely matched their larval width. C. foliascens and Ircinia sp., showed no specificity to surface microtopography, settling just as often to microtopography as to flat surfaces. The findings of this study question the sole reliance on chemical based larval settlement cues, previously established for some coral and sponge species, and demonstrate that specific physical cues (surface complexity) can also play an important role in larval settlement of coral reef sessile invertebrates.

Dynamics of confined reactive water in smectite clay-zeolite composites.

PubMed

Pitman, Michael C; van Duin, Adri C T

2012-02-15

The dynamics of water confined to mesoporous regions in minerals such as swelling clays and zeolites is fundamental to a wide range of resource management issues impacting many processes on a global scale, including radioactive waste containment, desalination, and enhanced oil recovery. Large-scale atomic models of freely diffusing multilayer smectite particles at low hydration confined in a silicalite cage are used to investigate water dynamics in the composite environment with the ReaxFF reactive force field over a temperature range of 300-647 K. The reactive capability of the force field enabled a range of relevant surface chemistry to emerge, including acid/base equilibria in the interlayer calcium hydrates and silanol formation on the edges of the clay and inner surface of the zeolite housing. After annealing, the resulting clay models exhibit both mono- and bilayer hydration structures. Clay surface hydration redistributed markedly and yielded to silicalite water loading. We find that the absolute rates and temperature dependence of water dynamics compare well to neutron scattering data and pulse field gradient measures from relevant samples of Ca-montmorillonite and silicalite, respectively. Within an atomistic, reactive context, our results distinguish water dynamics in the interlayer Ca(OH)(2)·nH(2)O environment from water flowing over the clay surface, and from water diffusing within silicalite. We find that the diffusion of water when complexed to Ca hydrates is considerably slower than freely diffusing water over the clay surface, and the reduced mobility is well described by a difference in the Arrhenius pre-exponential factor rather than a change in activation energy.

Catalytic ozonation of paracetamol using commercial and Pt-supported nanocomposites of Al2O3: The impact of ultrasound.

PubMed

Ziylan-Yavaş, Asu; Ince, Nilsun H

2018-01-01

The study is the assessment of commercial γ-Al 2 O 3 and its sonolytically modified nanocomposite in catalytic ozonation of paracetamol (PCT), which is an emerging water contaminant and a highly reactive compound with ozone. The results showed that commercial alumina was ineffective regardless of the solution pH, due to the low affinity of the catalyst surface for PCT and the high reactivity of the solute with molecular ozone. The modified catalyst, which was synthesized by decoration of the original surface with nanoparticles of platinum provided considerable improvement in the performance of the catalyst, particularly in mineralization of the target compound. The presence of OH scavenging agents in solution markedly retarded the rate of PCT oxidation and organic carbon decay, to signal the importance of radical-mediated reaction mechanisms on the degradation of the compound. Finally, the attempt to accelerate the reactions by running them in the presence of ultrasound was found inadequate for the early oxidation, but highly adequate for the longer mineralization process. The failure was attributed to the diffusion of a large fraction of ozone into the gaseous cavity bubbles (reduced probability of direct reactions) and the extreme conditions of cavitation collapse that partially damaged the catalyst surface. The success (in mineralization) was explained by the shift of the reaction site from the bulk solution (poor adsorption on catalyst surfaces) to the solid surface and the gaseous cavity bubbles (via enhanced hydrophobicity), both being considerably more active reaction media. Copyright © 2017 Elsevier B.V. All rights reserved.

Material Gradients in Oxygen System Components Improve Safety

NASA Technical Reports Server (NTRS)

Forsyth, Bradley S.

2011-01-01

Oxygen system components fabricated by Laser Engineered Net Shaping (TradeMark) (LENS(TradeMark)) could result in improved safety and performance. LENS(TradeMark) is a near-net shape manufacturing process fusing powdered materials injected into a laser beam. Parts can be fabricated with a variety of elemental metals, alloys, and nonmetallic materials without the use of a mold. The LENS(TradeMark) process allows the injected materials to be varied throughout a single workpiece. Hence, surfaces exposed to oxygen could be constructed of an oxygen-compatible material while the remainder of the part could be one chosen for strength or reduced weight. Unlike conventional coating applications, a compositional gradient would exist between the two materials, so no abrupt material boundary exists. Without an interface between dissimilar materials, there is less tendency for chipping or cracking associated with thermal-expansion mismatches.

Alternate concepts study extension. Volume 2: Part 4: Avionics

NASA Technical Reports Server (NTRS)

1971-01-01

A recommended baseline system is presented along with alternate avionics systems, Mark 2 avionics, booster avionics, and a cost summary. Analyses and discussions are included on the Mark 1 orbiter avionics subsystems, electrical ground support equipment, and the computer programs. Results indicate a need to define all subsystems of the baseline system, an installation study to determine the impact on the crew station, and a study on access for maintenance.

Protecting the turf: The effect of territorial marking on others' creativity.

PubMed

Brown, Graham; Baer, Markus

2015-11-01

Territorial marking allows people to communicate that a territory has been claimed. Across 2 studies, we examine the impact of territorial marking of one's ideas on others' invited creativity when asked to provide feedback. Integrating research on territoriality and self-construal, we examine the effect of control-oriented marking on invited creativity (Study 1), and the extent to which an independent versus interdependent self-construal moderates this effect (Study 2). Results of Study 1 demonstrate that the use of control-oriented marking to communicate a territorial claim over one's ideas inhibits invited creativity, and this effect is mediated by intrinsic motivation. Also consistent with our hypotheses, the results of Study 2 show that self-construal moderates the effect of control-oriented marking on others' intrinsic motivation and creativity. Marking diminishes invited creativity among people with an independent self-construal but serves to enhance the creativity of those with an interdependent self-construal. Consistent with Study 1, intrinsic motivation mediates this moderated effect. Our results highlight the important but heretofore understudied role of territoriality in affecting others' creativity as well as the role of independent versus interdependent self-construal in shaping this effect. (c) 2015 APA, all rights reserved).

Solar Wind Sputtering of Lunar Surface Materials: Role and Some Possible Implications of Potential Sputtering

NASA Technical Reports Server (NTRS)

Barghouty, A. F.; Adams, J. H., Jr.; Meyer, F.; Reinhold, c.

2010-01-01

Solar-wind induced sputtering of the lunar surface includes, in principle, both kinetic and potential sputtering. The role of the latter mechanism, however, in many focused studies has not been properly ascertained due partly to lack of data but can also be attributed to the assertion that the contribution of solar-wind heavy ions to the total sputtering is quite low due to their low number density compared to solar-wind protons. Limited laboratory measurements show marked enhancements in the sputter yields of slow-moving, highly-charged ions impacting oxides. Lunar surface sputtering yields are important as they affect, e.g., estimates of the compositional changes in the lunar surface, its erosion rate, as well as its contribution to the exosphere as well as estimates of hydrogen and water contents. Since the typical range of solar-wind ions at 1 keV/amu is comparable to the thickness of the amorphous rim found on lunar soil grains, i.e. few 10s nm, lunar simulant samples JSC-1A AGGL are specifically enhanced to have such rims in addition to the other known characteristics of the actual lunar soil particles. However, most, if not all laboratory studies of potential sputtering were carried out in single crystal targets, quite different from the rim s amorphous structure. The effect of this structural difference on the extent of potential sputtering has not, to our knowledge, been investigated to date.

Distributed collaborative response surface method for mechanical dynamic assembly reliability design

NASA Astrophysics Data System (ADS)

Bai, Guangchen; Fei, Chengwei

2013-11-01

Because of the randomness of many impact factors influencing the dynamic assembly relationship of complex machinery, the reliability analysis of dynamic assembly relationship needs to be accomplished considering the randomness from a probabilistic perspective. To improve the accuracy and efficiency of dynamic assembly relationship reliability analysis, the mechanical dynamic assembly reliability(MDAR) theory and a distributed collaborative response surface method(DCRSM) are proposed. The mathematic model of DCRSM is established based on the quadratic response surface function, and verified by the assembly relationship reliability analysis of aeroengine high pressure turbine(HPT) blade-tip radial running clearance(BTRRC). Through the comparison of the DCRSM, traditional response surface method(RSM) and Monte Carlo Method(MCM), the results show that the DCRSM is not able to accomplish the computational task which is impossible for the other methods when the number of simulation is more than 100 000 times, but also the computational precision for the DCRSM is basically consistent with the MCM and improved by 0.40˜4.63% to the RSM, furthermore, the computational efficiency of DCRSM is up to about 188 times of the MCM and 55 times of the RSM under 10000 times simulations. The DCRSM is demonstrated to be a feasible and effective approach for markedly improving the computational efficiency and accuracy of MDAR analysis. Thus, the proposed research provides the promising theory and method for the MDAR design and optimization, and opens a novel research direction of probabilistic analysis for developing the high-performance and high-reliability of aeroengine.

Noninvasive computed tomography-guided marking technique for peripheral pulmonary nodules

PubMed Central

Matsuura, Yosuke; Nakao, Masayuki; Ichinose, Junji; Nakagawa, Ken; Okumura, Sakae

2016-01-01

Background Identification of the exact location of small peripheral pulmonary nodules during thoracoscopic wedge resection (TWR) is crucial. We describe a new method of computed tomography (CT)-guided marking without puncturing the visceral pleura (VP) for minimally palpable pulmonary nodules. Methods Preoperative CT scans were performed 1 day before TWR with the patient in the lateral decubitus position. Under CT guidance, we marked the skin over the pulmonary nodule. During TS, an indwelling catheter was inserted perpendicular to the marked skin surface and put a mark with gentian violet (Pyoktanin blue®, Wako Pure Chemical Industries, Osaka, Japan) onto the VP. We palpated the nodules near the mark(s) and performed TWR. Results Between October 2012 and April 2016, we performed CT-guided marking in 54 patients (24 males and 30 females, median age 65 years). Cases included 39 primary lung cancers, 10 metastatic lung tumors, and 5 benign tumors. The mean diameter of the nodules was 10 mm (range, 3–26 mm), and the mean distance of the nodule from the VP was 4 mm (range, 0–17 mm). The mean time of intraoperative marking was 3.5 min (range, 1–4.5 min). The mean distance from the nodule to the marking point was 7.0 mm (range, 0–30 mm). We were able to identify the location of the nodule using this procedure in 53 patients (98%). Hematoma of the chest wall after marking was observed in one patient. There were no other complications. Conclusions This marking technique is a simple, economic, and effective procedure to locate small peripheral pulmonary nodules during TWR. PMID:28066668

Handheld lasers allow efficient detection of fluorescent marked organisms in the field.

PubMed

Rice, Kevin B; Fleischer, Shelby J; De Moraes, Consuelo M; Mescher, Mark C; Tooker, John F; Gish, Moshe

2015-01-01

Marking organisms with fluorescent dyes and powders is a common technique used in ecological field studies that monitor movement of organisms to examine life history traits, behaviors, and population dynamics. External fluorescent marking is relatively inexpensive and can be readily employed to quickly mark large numbers of individuals; however, the ability to detect marked organisms in the field at night has been hampered by the limited detection distances provided by portable fluorescent ultraviolet lamps. In recent years, significant advances in LED lamp and laser technology have led to development of powerful, low-cost ultraviolet light sources. In this study, we evaluate the potential of these new technologies to improve detection of fluorescent-marked organisms in the field and to create new possibilities for tracking marked organisms in visually challenging environments such as tree canopies and aquatic habitats. Using handheld lasers, we document a method that provides a fivefold increase in detection distance over previously available technologies. This method allows easy scouting of tree canopies (from the ground), as well as shallow aquatic systems. This novel detection method for fluorescent-marked organisms thus promises to significantly enhance the use of fluorescent marking as a non-destructive technique for tracking organisms in natural environments, facilitating field studies that aim to document otherwise inaccessible aspects of the movement, behavior, and population dynamics of study organisms, including species with significant economic impacts or relevance for ecology and human health.

Splashing Threshold of Oblique Droplet Impacts on Surfaces of Various Wettability.

PubMed

Aboud, Damon G K; Kietzig, Anne-Marie

2015-09-15

Oblique drop impacts were performed at high speeds (up to 27 m/s, We > 9000) with millimetric water droplets, and a linear model was applied to define the oblique splashing threshold. Six different sample surfaces were tested: two substrate materials of different inherent surface wettability (PTFE and aluminum), each prepared with three different surface finishes (smooth, rough, and textured to support superhydrophobicity). Our choice of surfaces has allowed us to make several novel comparisons. Considering the inherent surface wettability, we discovered that PTFE, as the more hydrophobic surface, exhibits lower splashing thresholds than the hydrophilic surface of aluminum of comparable roughness. Furthermore, comparing oblique impacts on smooth and textured surfaces, we found that asymmetrical spreading and splashing behaviors occurred under a wide range of experimental conditions on our smooth surfaces; however, impacts occurring on textured surfaces were much more symmetrical, and one-sided splashing occurred only under very specific conditions. We attribute this difference to the air-trapping nature of textured superhydrophobic surfaces, which lowers the drag between the spreading lamella and the surface. The reduced drag affects oblique drop impacts by diminishing the effect of the tangential component of the impact velocity, causing the impact behavior to be governed almost exclusively by the normal velocity. Finally, by comparing oblique impacts on superhydrophobic surfaces at different impact angles, we discovered that although the pinning transition between rebounding and partial rebounding is governed primarily by the normal impact velocity, there is also a weak dependence on the tangential velocity. As a result, pinning is inhibited in oblique impacts. This led to the observation of a new behavior in highly oblique impacts on our superhydrophobic surfaces, which we named the stretched rebound, where the droplet is extended into an elongated pancake shape and rebounds while still outstretched, without exhibiting a recession phase.

Bay breeze climatology at two sites along the Chesapeake bay from 1986-2010: Implications for surface ozone.

PubMed

Stauffer, Ryan M; Thompson, Anne M

Hourly surface meteorological measurements were coupled with surface ozone (O 3 ) mixing ratio measurements at Hampton, Virginia and Baltimore, Maryland, two sites along the Chesapeake Bay in the Mid-Atlantic United States, to examine the behavior of surface O 3 during bay breeze events and quantify the impact of the bay breeze on local O 3 pollution. Analyses were performed for the months of May through September for the years 1986 to 2010. The years were split into three groups to account for increasingly stringent environmental regulations that reduced regional emissions of nitrogen oxides (NO x ): 1986-1994, 1995-2002, and 2003-2010. Each day in the 25-year record was marked either as a bay breeze day, a non-bay breeze day, or a rainy/cloudy day based on the meteorological data. Mean eight hour (8-h) averaged surface O 3 values during bay breeze events were 3 to 5 parts per billion by volume (ppbv) higher at Hampton and Baltimore than on non-bay breeze days in all year periods. Anomalies from mean surface O 3 were highest in the afternoon at both sites during bay breeze days in the 2003-2010 study period. In conjunction with an overall lowering of baseline O 3 after the 1995-2002 period, the percentage of total exceedances of the Environmental Protection Agency (EPA) 75 ppbv 8-h O 3 standard that occurred on bay breeze days increased at Hampton for 2003-2010, while remaining steady at Baltimore. These results suggest that bay breeze circulations are becoming more important to causing exceedance events at particular sites in the region, and support the hypothesis of Martins et al. (2012) that highly localized meteorology increasingly drives air quality events at Hampton.

Scattering effects of machined optical surfaces

NASA Astrophysics Data System (ADS)

Thompson, Anita Kotha

1998-09-01

Optical fabrication is one of the most labor-intensive industries in existence. Lensmakers use pitch to affix glass blanks to metal chucks that hold the glass as they grind it with tools that have not changed much in fifty years. Recent demands placed on traditional optical fabrication processes in terms of surface accuracy, smoothnesses, and cost effectiveness has resulted in the exploitation of precision machining technology to develop a new generation of computer numerically controlled (CNC) optical fabrication equipment. This new kind of precision machining process is called deterministic microgrinding. The most conspicuous feature of optical surfaces manufactured by the precision machining processes (such as single-point diamond turning or deterministic microgrinding) is the presence of residual cutting tool marks. These residual tool marks exhibit a highly structured topography of periodic azimuthal or radial deterministic marks in addition to random microroughness. These distinct topographic features give rise to surface scattering effects that can significantly degrade optical performance. In this dissertation project we investigate the scattering behavior of machined optical surfaces and their imaging characteristics. In particular, we will characterize the residual optical fabrication errors and relate the resulting scattering behavior to the tool and machine parameters in order to evaluate and improve the deterministic microgrinding process. Other desired information derived from the investigation of scattering behavior is the optical fabrication tolerances necessary to satisfy specific image quality requirements. Optical fabrication tolerances are a major cost driver for any precision optical manufacturing technology. The derivation and control of the optical fabrication tolerances necessary for different applications and operating wavelength regimes will play a unique and central role in establishing deterministic microgrinding as a preferred and a cost-effective optical fabrication process. Other well understood optical fabrication processes will also be reviewed and a performance comparison with the conventional grinding and polishing technique will be made to determine any inherent advantages in the optical quality of surfaces produced by other techniques.

The Impact of HECS Debt on Australian Students' Tertiary Academic Performance

ERIC Educational Resources Information Center

Birch, Elisa R.; Miller, Paul W.

2006-01-01

The Australian literature suggests that students' academic success in tertiary education is principally influenced by their university entrance score. Personal, secondary school and university characteristics have more minor impacts on tertiary outcomes. Little research has been undertaken into the relationship between students' marks and the…

The detailed analysis of the changes of murine dendritic cells (DCs) induced by thymic peptide

PubMed Central

Hu, Xiaofang; Zheng, Wei; Wang, Lu; Wan, Nan; Wang, Bing; Li, Weiwei; Hua, Hui; Hu, Xu; Shan, Fengping

2012-01-01

The aim of present research is to analyze the detailed changes of dendritic cells (DCs) induced by pidotimod(PTD). These impacts on DCs of both bone marrow derived DCs and established DC2.4 cell line were assessed with use of conventional scanning electron microscopy (SEM), flow cytometry (FCM), transmission electron microscopy (TEM), cytochemistry assay FITC-dextran, bio-assay and enzyme linked immunosorbent assay (ELISA). We demonstrated the ability of PTD to induce DC phynotypic and functional maturation as evidenced by higher expression of key surface molecules such as MHC II, CD80 and CD86. The functional tests proved the downregulation of ACP inside the DCs, occurred when phagocytosis of DCs decreased, with simultaneously antigen presentation increased toward maturation. Finally, PTD also stimulated production of more cytokine IL-12 and less TNF-α. Therefore it is concluded that PTD can markedly exert positive induction to murine DCs. PMID:22863756

Entering the Anthropocene

NASA Astrophysics Data System (ADS)

Vince, Gaia

2016-04-01

There is growing evidence that we are now entering a new geological age defined by human influence on the planet, the Anthropocene. Millions of years from now, a stripe in the accumulated layers of rock on Earth's surface will reveal our human fingerprint just as we can see evidence of dinosaurs in rocks of the Jurassic, or the explosion of life that marks the Cambrian. There is now no part of the planet untouched by human influence. The realisation that we wield such planetary power requires a quite extraordinary shift in perception, fundamentally toppling the scientific, cultural and religious philosophies that define our place in the world. This session explores these issues and examines our new relationship with nature now that we so strongly influence the biosphere. And this session will look at what the impacts of our planetary changes mean for us, and how we might deal with the consequences of the Anthropocene we have created.

Mimas Against the Rings

NASA Image and Video Library

2005-08-05

During its close flyby of Saturn's moon Mimas on Aug. 2, 2005, Cassini caught a glimpse of Mimas against the broad expanse of Saturn's rings. The Keeler Gap in the outer A ring, in which Cassini spied a never-before-seen small moon (see PIA06237), is at the upper right. The ancient, almost asteroid-like surface of Mimas is evident in its crater-upon-crater appearance. Even the material which has slumped down into the bottom of some of its craters bears the marks of later impacts. This image was taken through the clear filter of the Cassini spacecraft narrow-angle camera at a distance of 68,000 kilometers (42,500 miles) from Mimas and very near closest approach. The smallest features seen on the moon are about 400 meters wide (440 yards); the Sun-Mimas-Cassini angle is 44 degrees. http://photojournal.jpl.nasa.gov/catalog/PIA06412

Crumpled Heat Shield

NASA Technical Reports Server (NTRS)

2008-01-01

The Phoenix Mars Lander's Surface Stereo Imager took this image of the spacecraft's crumpled heat shield on Sept. 16, 2008, the 111th Martian day of the mission.

The 2-1/2 meter (about 8-1/2 feet) heat shield landed southeast of Phoenix, about halfway between the spacecraft and its backshell/parachute. The backshell/parachute touched ground 300 meters (1,000 ft) to the south of the lander.

The dark area to the right of the heat shield is the 'bounce mark' it made on impact with the Red Planet. This image is the highest-resolution image that will likely be taken by the lander, and is part of the 1,500-image 'Happily Ever After' panorama.

The Phoenix mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is led by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

The influence of wind farm development on the hydrochemistry and ecology of an upland stream.

PubMed

Millidine, K J; Malcolm, I A; McCartney, A; Laughton, R; Gibbins, C N; Fryer, R J

2015-08-01

Despite perceptions of pristine condition, upland environments are increasingly subject to a range of anthropogenic pressures including air pollution, climate change, land-use change and evolving land management strategies. Although they have received little attention to date, the large-scale development of upland wind farms also has the potential to disturb vegetation and soils, alter hydrology and water quality and, thus, impact freshwater ecosystems. This paper presents the findings of a 5-year study of the impacts of wind farm construction on the freshwater environment. Data on water quality, invertebrate and fish populations were collected for 2 years before construction and for the following 3 years covering the construction period and the initial period of the farm's operation. In contrast to previous studies, the impacts of the wind farm development were assessed for a suite of potentially affected hydrochemical variables using a before-after-control-impact (BACI) analysis that allowed separation of construction effects from spatial and temporal variability in hydroclimatological conditions, thereby providing an improved, more robust evidence base. There was a small but significant negative effect of construction on pH, alkalinity (Alk) and acid neutralising capacity (ANC) in the upper part of the treatment catchment, which was where the wind farm was situated. The effects were more marked under higher flow conditions. It is hypothesised that this reflects changes in hydrological processes with increased near-surface runoff or organic acid mobilisation. There was no indication that either invertebrate community structure or fish densities were impacted by construction and the resulting effects on water quality.

Mark 3 VLBI system: Tropospheric calibration subsystems

NASA Technical Reports Server (NTRS)

Resch, G. M.

1980-01-01

Tropospheric delay calibrations are implemented in the Mark 3 system with two subsystems. Estimates of the dry component of tropospheric delay are provided by accurate barometric data from a subsystem of surface meteorological sensors (SMS). An estimate of the wet component of tropospheric delay is provided by a water vapor radiometer (WVR). Both subsystems interface directly to the ASCII Transceiver bus of the Mark 3 system and are operated by the control computer. Seven WVR's under construction are designed to operate in proximity to a radio telescope and can be commanded to point along the line-of-sight to a radio source. They should provide a delay estimate that is accurate to the + or - 2 cm level.

Infrared technique for decoding of invisible laser markings

NASA Astrophysics Data System (ADS)

Haferkamp, Heinz; Jaeschke, Peter; Stein, Johannes; Goede, Martin

2002-03-01

Counterfeiting and product piracy continues to be an important issue not only for the Western industry, but also for the society in general. Due to the drastic increase in product imitation and the request for plagiarism protection as well as for reducing thefts there is a high interest in new protection methods providing new security features. The method presented here consists of security markings which are included below paint layers. These markings are invisible for the human eye due to the non-transparency of the upper layers in the visible spectral range. However, the markings can be detected by an infrared technique taking advantage on the partial transparency of the upper paint layers in the IR-region. Metal sheets are marked using laser radiation. The beam of a Nd:YAG-laser provides a modification of the surface structure, resulting in dark markings due to the annealing effect. After coating of the laser-marked material, the markings are invisible for the bare eye. In order to read out the invisible information below the coating, an infrared reflection technique is used. The samples are illuminated with halogen lamps or infrared radiators. Many coating materials (i. e. paints) show a certain transparency in the mid-infrared region, especially between 3 - 5 micrometers . The reflected radiation is detected using an IR-camera with a sensitivity range from 3.4 - 5 micrometers . Due to the different reflection properties between the markings and their surrounding, the information can be detected.

Ion-induced crystal damage during plasma-assisted MBE growth of GaN layers

NASA Astrophysics Data System (ADS)

Kirchner, V.; Heinke, H.; Birkle, U.; Einfeldt, S.; Hommel, D.; Selke, H.; Ryder, P. L.

1998-12-01

Gallium nitride layers were grown by plasma-assisted molecular-beam epitaxy on (0001)-oriented sapphire substrates using an electron cyclotron resonance (ECR) and a radio frequency (rf) plasma source. An applied substrate bias was varied from -200 to +250 V, resulting in a change of the density and energy of nitrogen ions impinging the growth surface. The layers were investigated by high-resolution x-ray diffractometry and high-resolution transmission electron microscopy (HRTEM). Applying a negative bias during growth has a marked detrimental effect on the crystal perfection of the layers grown with an ECR plasma source. This is indicated by a change in shape and width of (0002) and (202¯5) reciprocal lattice points as monitored by triple axis x-ray measurements. In HRTEM images, isolated basal plane stacking faults were found, which probably result from precipitation of interstitial atoms. The crystal damage in layers grown with a highly negative substrate bias is comparable to that observed for ion implantation processes at orders of magnitude larger ion energies. This is attributed to the impact of ions on the growing surface. None of the described phenomena was observed for the samples grown with the rf plasma source.

A Preliminary Anthropometry Standard for Australian Army Equipment Evaluation

DTIC Science & Technology

2014-08-01

UNCLASSIFIED Authors Mark Edwards Land Division Mark Edwards holds an undergraduate degree in Industrial Design , a Masters in Ergonomics ...equipment. Given that a built system is not a requirement of the processes described, this standard can also be used early in the design process to de...risk the design process. It must be noted that the data provided in this report are representative of the 2012 ADF Army population. The impacts

Safety of community drinking-water and outbreaks of waterborne enteric disease: Israel, 1976-97.

PubMed Central

Tulchinsky, T. H.; Burla, E.; Clayman, M.; Sadik, C.; Brown, A.; Goldberger, S.

2000-01-01

Waterborne disease remains a major public health problem in many countries. We report findings on nearly three decades of waterborne disease in Israel and the part these diseases play in the total national burden of enteric disease. During the 1970s and 1980s, Israel's community water supplies were frequently of poor quality according to the microbiological standards at that time, and the country experienced many outbreaks of waterborne enteric disease. New regulations raised water quality standards and made chlorination of community water supplies mandatory, as well as imposing more stringent guidelines on maintaining water sources and distribution systems for both surface water and groundwater. This was followed by improved compliance and water quality, and a marked decline in the number of outbreaks of waterborne disease; no outbreaks were detected between 1992 and 1997. The incidence of waterborne salmonellosis, shigellosis, and typhoid declined markedly as proportions of the total burden of these diseases, but peaked during the time in which there were frequent outbreaks of waterborne disease (1980-85). Long-term trends in the total incidence of reported infectious enteric diseases from all sources, including typhoid, shigellosis, and viral hepatitis (all types) declined, while the total incidence of salmonellosis increased. Mandatory chlorination has had an important impact on improving water quality, in reducing outbreaks of waterborne disease in Israel, and reducing the total burden of enteric disease in the country. PMID:11196499

The Role of Interface Shape on the Impact Characteristics and Cranial Fracture Patterns Using the Immature Porcine Head Model,.

PubMed

Vaughan, Patrick E; Vogelsberg, Caitlin C M; Vollner, Jennifer M; Fenton, Todd W; Haut, Roger C

2016-09-01

The forensic literature suggests that when adolescents fall onto edged and pointed surfaces, depressed fractures can occur at low energy levels. This study documents impact biomechanics and fracture characteristics of infant porcine skulls dropped onto flat, curved, edged, and focal surfaces. Results showed that the energy needed for fracture initiation was nearly four times higher against a flat surface than against the other surfaces. While characteristic measures of fracture such as number and length of fractures did not vary with impact surface shape, the fracture patterns did depend on impact surface shape. While experimental impacts against the flat surface produced linear fractures initiating at sutural boundaries peripheral to the point of impact (POI), more focal impacts produced depressed fractures initiating at the POI. The study supported case-based forensic literature suggesting cranial fracture patterns depend on impact surface shape and that fracture initiation energy is lower for more focal impacts. © 2016 American Academy of Forensic Sciences.

Evolution of genetic polymorphisms of Plasmodium falciparum merozoite surface protein (PfMSP) in Thailand.

PubMed

Kuesap, Jiraporn; Chaijaroenkul, Wanna; Ketprathum, Kanchanok; Tattiyapong, Puntanat; Na-Bangchang, Kesara

2014-02-01

Plasmodium falciparum malaria is a major public health problem in Thailand due to the emergence of multidrug resistance. The understanding of genetic diversity of malaria parasites is essential for developing effective drugs and vaccines. The genetic diversity of the merozoite surface protein-1 (PfMSP-1) and merozoite surface protein-2 (PfMSP-2) genes was investigated in a total of 145 P. falciparum isolates collected from Mae Sot District, Tak Province, Thailand during 3 different periods (1997-1999, 2005-2007, and 2009-2010). Analysis of genetic polymorphisms was performed to track the evolution of genetic change of P. falciparum using PCR. Both individual genes and their combination patterns showed marked genetic diversity during the 3 study periods. The results strongly support that P. falciparum isolates in Thailand are markedly diverse and patterns changed with time. These 2 polymorphic genes could be used as molecular markers to detect multiple clone infections and differentiate recrudescence from reinfection in P. falciparum isolates in Thailand.

10 CFR 61.52 - Land disposal facility operation and disposal site closure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... meters below the top surface of the cover or must be disposed of with intruder barriers that are designed... mapped by means of a land survey. Near-surface disposal units must be marked in such a way that the boundaries of each unit can be easily defined. Three permanent survey marker control points, referenced to...

10 CFR 61.52 - Land disposal facility operation and disposal site closure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... meters below the top surface of the cover or must be disposed of with intruder barriers that are designed... mapped by means of a land survey. Near-surface disposal units must be marked in such a way that the boundaries of each unit can be easily defined. Three permanent survey marker control points, referenced to...

10 CFR 61.52 - Land disposal facility operation and disposal site closure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... meters below the top surface of the cover or must be disposed of with intruder barriers that are designed... mapped by means of a land survey. Near-surface disposal units must be marked in such a way that the boundaries of each unit can be easily defined. Three permanent survey marker control points, referenced to...

10 CFR 61.52 - Land disposal facility operation and disposal site closure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... meters below the top surface of the cover or must be disposed of with intruder barriers that are designed... mapped by means of a land survey. Near-surface disposal units must be marked in such a way that the boundaries of each unit can be easily defined. Three permanent survey marker control points, referenced to...

10 CFR 61.52 - Land disposal facility operation and disposal site closure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... meters below the top surface of the cover or must be disposed of with intruder barriers that are designed... mapped by means of a land survey. Near-surface disposal units must be marked in such a way that the boundaries of each unit can be easily defined. Three permanent survey marker control points, referenced to...

Cannibalism versus funerary defleshing and disarticulation after a period of decay: comparisons of bone modifications from four prehistoric sites.

PubMed

Bello, Silvia M; Wallduck, Rosalind; Dimitrijević, Vesna; Živaljević, Ivana; Stringer, Chris B

2016-12-01

Humanly induced modifications on human and non-human bones from four archaeological sites of known funerary rituals (one interpreted as cannibalism and three interpreted as funerary defleshing and disarticulation after a period of decay) were analyzed to ascertain whether macromorphological and micromorphological characteristics of cut marks can be used to distinguish cannibalistic from secondary burial practices. Four collections were analyzed: the Magdalenian assemblage from Gough's Cave (UK) and the Mesolithic-Neolithic bone samples from Lepenski Vir, Padina and Vlasac (Serbia). A total of 647 cut marks (345 on human and 302 on non-human remains) were imaged and measured using an optical surface measurement system, the Alicona InfiniteFocus, housed at the Natural History Museum (London, UK). The frequency of cut marks at Gough's Cave exceeds 65%, while it is below 1% in the Serbian sites, and no human tooth marks and only one case of percussion damage have been observed on the three Serbian collections. The distribution of cut marks on human bones is comparable in the four assemblages. Cannibalized human remains, however, present a uniform cut mark distribution, which can be associated with disarticulation of persistent and labile articulations, and the scalping and filleting of muscles. For secondary burials where modification occurred after a period of decay, disarticulation marks are less common and the disarticulation of labile joints is rare. The micromorphometric analyses of cut marks on human and non-human remains suggest that cut marks produced when cleaning partially decayed bodies are significantly different from cut marks produced during butchery of fresh bodies. A distinction between cannibalism and secondary treatment of human bodies can be made based on frequency, distribution and micromorphometric characteristics of cut marks. © 2016 Wiley Periodicals, Inc.

Evidence for deposition of 10 million tonnes of impact spherules across four continents 12,800 y ago

USGS Publications Warehouse

Wittke, James H.; Weaver, James C.; Bunch, Ted E.; Kennett, James P.; Kennett, Douglas J.; Moore, Andrew M.T.; Hillman, Gordon C.; Tankersly, Kenneth B.; Goodyear, Albert C.; Moore, Christopher R.; Daniel, I. Randolph; Ray, Jack H.; Lopinot, Neal H.; Ferraro, David; Israde-Alcántara, Isabel; Bischoff, James L.; DeCarli, Paul S.; Hermes, Robert E.; Kloosterman, Johan B.; Revay, Zsolt; Howard, George A.; Kimbel, David R.; Kletetschka, Gunther; Nabelek, Ladislav; Lipo, Carl P.; Sakai, Sachiko; West, Allen; Firestone, Richard B.

2013-01-01

Airbursts/impacts by a fragmented comet or asteroid have been proposed at the Younger Dryas onset (12.80 ± 0.15 ka) based on identification of an assemblage of impact-related proxies, including microspherules, nanodiamonds, and iridium. Distributed across four continents at the Younger Dryas boundary (YDB), spherule peaks have been independently confirmed in eight studies, but unconfirmed in two others, resulting in continued dispute about their occurrence, distribution, and origin. To further address this dispute and better identify YDB spherules, we present results from one of the largest spherule investigations ever undertaken regarding spherule geochemistry, morphologies, origins, and processes of formation. We investigated 18 sites across North America, Europe, and the Middle East, performing nearly 700 analyses on spherules using energy dispersive X-ray spectroscopy for geochemical analyses and scanning electron microscopy for surface microstructural characterization. Twelve locations rank among the world’s premier end-Pleistocene archaeological sites, where the YDB marks a hiatus in human occupation or major changes in site use. Our results are consistent with melting of sediments to temperatures >2,200 °C by the thermal radiation and air shocks produced by passage of an extraterrestrial object through the atmosphere; they are inconsistent with volcanic, cosmic, anthropogenic, lightning, or authigenic sources. We also produced spherules from wood in the laboratory at >1,730 °C, indicating that impact-related incineration of biomass may have contributed to spherule production. At 12.8 ka, an estimated 10 million tonnes of spherules were distributed across ∼50 million square kilometers, similar to well-known impact strewnfields and consistent with a major cosmic impact event.

Evidence for deposition of 10 million tonnes of impact spherules across four continents 12,800 y ago

PubMed Central

Wittke, James H.; Weaver, James C.; Bunch, Ted E.; Kennett, James P.; Kennett, Douglas J.; Moore, Andrew M. T.; Hillman, Gordon C.; Tankersley, Kenneth B.; Goodyear, Albert C.; Moore, Christopher R.; Daniel, I. Randolph; Ray, Jack H.; Lopinot, Neal H.; Ferraro, David; Israde-Alcántara, Isabel; Bischoff, James L.; DeCarli, Paul S.; Hermes, Robert E.; Kloosterman, Johan B.; Revay, Zsolt; Howard, George A.; Kimbel, David R.; Kletetschka, Gunther; Nabelek, Ladislav; Lipo, Carl P.; Sakai, Sachiko; West, Allen; Firestone, Richard B.

2013-01-01

Airbursts/impacts by a fragmented comet or asteroid have been proposed at the Younger Dryas onset (12.80 ± 0.15 ka) based on identification of an assemblage of impact-related proxies, including microspherules, nanodiamonds, and iridium. Distributed across four continents at the Younger Dryas boundary (YDB), spherule peaks have been independently confirmed in eight studies, but unconfirmed in two others, resulting in continued dispute about their occurrence, distribution, and origin. To further address this dispute and better identify YDB spherules, we present results from one of the largest spherule investigations ever undertaken regarding spherule geochemistry, morphologies, origins, and processes of formation. We investigated 18 sites across North America, Europe, and the Middle East, performing nearly 700 analyses on spherules using energy dispersive X-ray spectroscopy for geochemical analyses and scanning electron microscopy for surface microstructural characterization. Twelve locations rank among the world’s premier end-Pleistocene archaeological sites, where the YDB marks a hiatus in human occupation or major changes in site use. Our results are consistent with melting of sediments to temperatures >2,200 °C by the thermal radiation and air shocks produced by passage of an extraterrestrial object through the atmosphere; they are inconsistent with volcanic, cosmic, anthropogenic, lightning, or authigenic sources. We also produced spherules from wood in the laboratory at >1,730 °C, indicating that impact-related incineration of biomass may have contributed to spherule production. At 12.8 ka, an estimated 10 million tonnes of spherules were distributed across ∼50 million square kilometers, similar to well-known impact strewnfields and consistent with a major cosmic impact event. PMID:23690611

Spongy Surface

NASA Image and Video Library

2015-06-02

NASA Cassini imaging scientists processed this view of Saturn moon Hyperion, taken during a close flyby on May 31, 2015. This flyby marks the mission final close approach to Saturn largest irregularly shaped moon.

Sampling Artifacts from Conductive Silicone Tubing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Timko, Michael T.; Yu, Zhenhong; Kroll, Jesse

2009-05-15

We report evidence that carbon impregnated conductive silicone tubing used in aerosol sampling systems can introduce two types of experimental artifacts: 1) silicon tubing dynamically absorbs carbon dioxide gas, requiring greater than 5 minutes to reach equilibrium and 2) silicone tubing emits organic contaminants containing siloxane that adsorb onto particles traveling through it and onto downstream quartz fiber filters. The consequence can be substantial for engine exhaust measurements as both artifacts directly impact calculations of particulate mass-based emission indices. The emission of contaminants from the silicone tubing can result in overestimation of organic particle mass concentrations based on real-time aerosolmore » mass spectrometry and the off-line thermal analysis of quartz filters. The adsorption of siloxane contaminants can affect the surface properties of aerosol particles; we observed a marked reduction in the water-affinity of soot particles passed through conductive silicone tubing. These combined observations suggest that the silicone tubing artifacts may have wide consequence for the aerosol community and should, therefore, be used with caution. Gentle heating, physical and chemical properties of the particle carriers, exposure to solvents, and tubing age may influence siloxane uptake. The amount of contamination is expected to increase as the tubing surface area increases and as the particle surface area increases. The effect is observed at ambient temperature and enhanced by mild heating (<100 oC). Further evaluation is warranted.« less

Expansion analyses of strategic petroleum reserve in Bayou Choctaw : revised locations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehgartner, Brian L.; Park, Byoung Yoon

2010-11-01

This report summarizes a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by changing the locations of two caverns. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure, and well integrity are quantified.more » Two scenarios were used for the duration and timing of workover conditions where wellhead pressures are temporarily reduced to atmospheric pressure. The three expansion caverns are predicted to be structurally stable against tensile failure for both scenarios. Dilatant failure is not expected within the vicinity of the expansion caverns. Damage to surface structures is not predicted and there is not a marked increase in surface strains due to the presence of the three expansion caverns. The wells into the caverns should not undergo yield. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.« less

Flooding impacts on responses of a riparian consumer to cross-ecosystem subsidies.

PubMed

Greenwood, Michelle J; McIntosh, Angus R

2008-06-01

Landscape-driven processes impact the magnitude and direction of cross-ecosystem resource subsidies, but they may also control consumers' numerical and functional responses by altering habitat availability. We investigated effects of the interaction between habitat availability and subsidy level on populations of a riparian fishing spider, Dolomedes aquaticus, using a flood disturbance gradient in the Waimakariri River catchment, New Zealand. D. aquaticus predominantly eat aquatic prey as they hunt from the water surface. However, D. aquaticus biomass peaked at rivers with intermediate flood disturbance, rather than at less flood-prone rivers where the biomass of aquatic insect prey was markedly higher. Flooding positively influenced spider habitat quality, and an experimental manipulation at stable rivers indicated that unembedded cobbles, preferred D. aquaticus habitat, were a limiting factor, preventing response to the increased prey resource at stable sites. Potential terrestrial prey abundance was low, did not vary across the disturbance gradient, and is likely to have been a much smaller component of the fishing spiders' diet than aquatic insect prey. Thus landscape-driven factors not only controlled the magnitude of resource subsidies, but also influenced the ability of consumers to respond to them by altering the physical nature of the ecosystem boundary.

Factors defining value and direction of thermal pressure between the mine shafts and impact of the general mine natural draught on ventilation process of underground mining companies

NASA Astrophysics Data System (ADS)

Nikolaev, A. V.; Alymenko, N. I.; Kamenskikh, A. A.; Alymenko, D. N.; Nikolaev, V. A.; Petrov, A. I.

2017-10-01

The article specifies measuring data of air parameters and its volume flow in the shafts and on the surface, collected in BKPRU-2 (Berezniki potash plant and mine 2) («Uralkali» PJSC) in normal operation mode, after shutdown of the main mine fan (GVU) and within several hours. As a result of the test it has been established that thermal pressure between the mine shafts is active continuously regardless of the GVU operation mode or other draught sources. Also it has been discovered that depth of the mine shafts has no impact on thermal pressure value. By the same difference of shaft elevation marks and parameters of outer air between the shafts, by their different depth, thermal pressure of the same value will be active. Value of the general mine natural draught defined as an algebraic sum of thermal pressure values between the shafts depends only on the difference of temperature and pressure of outer air and air in the shaft bottoms on condition of shutdown of the air handling system (unit-heaters, air conditioning systems).

Behaviour of the Pleistocene marsupial lion deduced from claw marks in a southwestern Australian cave.

PubMed

Arman, Samuel D; Prideaux, Gavin J

2016-02-15

The marsupial lion, Thylacoleo carnifex, was the largest-ever marsupial carnivore, and is one of the most iconic extinct Australian vertebrates. With a highly-specialised dentition, powerful forelimbs and a robust build, its overall morphology is not approached by any other mammal. However, despite >150 years of attention, fundamental aspects of its biology remain unresolved. Here we analyse an assemblage of claw marks preserved on surfaces in a cave and deduce that they were generated by marsupial lions. The distribution and skewed size range of claw marks within the cave elucidate two key aspects of marsupial lion biology: they were excellent climbers and reared young in caves. Scrutiny of >10,000 co-located Pleistocene bones reveals few if any marsupial lion tooth marks, which dovetails with the morphology-based interpretation of the species as a flesh specialist.

The effects of padded surfaces on the risk for cervical spine injury.

PubMed

Nightingale, R W; Richardson, W J; Myers, B S

1997-10-15

This is an in vitro study comparing cervical spine injuries produced in rigid head impacts and in padded head impacts. To test the hypothesis that deformable impact surfaces pose a greater risk for cervical spine injury than rigid surfaces using a cadaver-based model that includes the effects of the head and torso masses. It is widely assumed that energy-absorbing devices that protect the head from injury also reduce the risk for neck injury. However, this has not been demonstrated in any experimental or epidemiologic study. On the contrary, some studies have shown that padded surfaces have no effect on neck injury risk, and others have suggested that they can increase risk. Experiments were performed on 18 cadaveric cervical spines to test 6 combinations of impact angle and impact surface padding. The impact surface was oriented at -15 degrees (posterior impact), 0 degree (vertex impact), or +15 degrees (anterior impact). The impact surface was either a 3-mm sheet of lubricated Teflon or 5 cm of polyurethane foam. Impacts onto padded surfaces produced significantly larger neck impulses (P = 0.00023) and a significantly greater frequency of cervical spine injuries than rigid impacts (P = 0.0375). The impact angle was also correlated with injury risk (P < 0.00001). These experiments suggest that highly deformable, padded contact surfaces should be used carefully in environments where there is the risk for cervical spine injury. The results also suggest that the orientation of the head, neck, and torso relative to the impact surface is of equal if not greater importance in neck injury risk.

The martian surface.

PubMed

Opik, E J

1966-07-15

With the scarcity of factual data and the difficulty of applying crucial tests, many of the properties of the Martian surface remain a mystery; the planet may become a source of great surprises in the future. In the following, the conclusions are enumerated more or less in the order of their reliability, the more certain ones first, conjectures or ambiguous interpretations coming last. Even if they prove to be wrong, they may serve as a stimulus for further investigation. Impact craters on Mars, from collisions with nearby asteroids and other stray bodies, were predicted 16 years ago (5-7) and are now verified by the Mariner IV pictures. The kink in the frequency curve of Martian crater diameters indicates that those larger than 20 kilometers could have survived aeolian erosion since the "beginning." They indicate an erosion rate 30 times slower than that in terrestrial deserts and 70 times faster than micrometeorite erosion on the moon. The observed number, per unit area, of Martian craters larger than 20 kilometers exceeds 4 times that calculated from the statistical theory of interplanetary collisions with the present population of stray bodies and for a time interval of 4500 million years, even when allowance is made for the depletion of the Martian group of asteroids, which were more numerous in the past. This, and the low eroded rims of the Martian craters suggest that many of the craters have survived almost since the formation of the crust. Therefore, Mars could not have possessed a dense atmosphere for any length of time. If there was abundant water for the first 100 million years or so, before it escaped it could have occurred only in the solid state as ice and snow, with but traces of vapor in the atmosphere, on account of the low temperature caused by the high reflectivity of clouds and snow. For Martian life there is thus the dilemma: with water, it is too cold; without, too dry. The crater density on Mars, though twice that in lunar maria, is much smaller than the "saturation density" of lunar highlands. Many primeval craters, those from the last impacts which formed the planet, must have become erased, either by late impacts of preferentially surviving large asteroids or by a primeval atmosphere which rapidly escaped. The tenuous Martian atmosphere may have originated entirely from outgassing of surface rocks by asteroidal impacts, which also could have produced some molten lava. The role of genuine volcanism on Mars must have been insignificant, if any. The large amplitude in temperature indicates that the Martian upper soil, equally in the bright and the dark areas, is of a porous unconsolidated structure, with a thermal conductivity as low as that of atmospheric air. Limb darkening at full phase in green, yellow, and red light indicates absorption by atmospheric haze, aerosols, and dust. The loss of contrast in the blue and violet is caused by stronger absorptivity of the haze, which is almost as dark as soot, and not by a true decrease in contrast of the surface markings. Photometric measurementsin the blue reveal a residual contrast of 5 to 7 percent between the markings in 1958, invisible to the eye at a time when there was no "blue clearing." The surface brightness of the maria was surprisingly uniform in 1958 (late summer in the southern hemisphere), while the continentes showed considerable variation. In view of the spotty microstructure of the Martian surface as revealed by Mariner IV, and the lack of a sharp border between a mare and a continens, it seems that all the difference consists in the relative number of small dark and bright areas in the surface mosaic. If there is vegetation on Mars, it should be concentrated in the darkarea elements, measuring 10 to 100 kilometers. Vegetation is the best hypothesis to account for seasonal changes in the maria and for the persistence of these formations despite dust storms of global extent. Survival of vegetation in the extreme dryness of the Martian climate could depend on the low night-time temperature and deposition of hoarfrost, which could melt into droplets after sunrise, before evaporating. If not vegetation, it must be something thing specifically Martian; no other hypothesis hitherto proposed is able to account for the facts. However, the infrared bands which at one time were thought to be associated with the presence of organic matter, belong to heavy water in the terrestrial atmosphere. The conversion of a former bright area into a dark one in 1954, over some 1 million square kilometers, is the largest recorded change of this kind. Even on the vegetation hypothesis, it eludes satisfactory explanation. Relatively bright areas observed in the blue and violet in polar regions and elsewhere on the limb can be explained by a greater transparency of the atmosphere,its dust content being decreased by a downward (anticyclonic) current. The surface, of a greater reflecting power than the atmospheric smoke, then becomes visible. The sudden explosion-like occurrence of yellow or gray clouds, reducing atmospheric transparency and surface contrast, could be due to impacts of asteroids; in such a case, however, the number of unobservable small asteroids, down to 30 to 40 meters in diameter, should greatly exceed the number extrapolated from the larger members of the group. A "meteoritic" increment in numbers, instead of the asteroidal one, would be required. special observations with large Schmidt telescopes could settle this crucial question. The Martian "oases," centers of "canal" systems, could be impact creters. The canals may be real formations, without sharp borders and 100 to 200 kilometers wide, due to a systematic alignment. of the dark surface elements. They may indicate cracks in the planet's crust, radiating from the point of impact.

Measuring the Impact of High Quality Instant Feedback on Learning

ERIC Educational Resources Information Center

Nutbrown, Stephen; Higgins, Colin; Beesley, Su

2016-01-01

This paper examines the impact of a novel assessment technique that has been used to improve the feedback given to second year Computer Science students at the University of Nottingham. Criteria for effective, high quality feedback are discussed. An automated marking system (The Marker's Apprentice--TMA) produces instant feedback in synergy with…

Comparison between fingerprints of the epidermis and dermis: Perspectives in the identifying of corpses.

PubMed

Mizokami, Leila Lopes; Silva, Lara Rosana Vieira; Kückelhaus, Selma Aparecida Souza

2015-07-01

In forensic science, the putrefaction, maceration, mummification or burning make it difficult to collect the fingerprints of the epidermis for identification purposes. In such cases, the comparison between fingerprints collected from the dermal surface and the ante mortem pattern of the epidermal surface archived in databases must be performed. Therefore, considering that the identification of corpses is done by comparison of fingerprints on different surfaces, this study aimed to compare the epidermal and the dermal fingerprints to determine the discrepancies between the minutiae of both surfaces. The study was conducted with excised fingers of 19 fresh adult corpses. Once selected, excised and photographed, the fingers were subjected to maceration with 0.5% acetic acid solution for the removal of the epidermal glove and for registering the dermal fingerprint. Then, an area of 1cm(2) in the epidermal and dermal photographies was selected and the minutiae of each were separately marked by an expert in identification. The comparison between minutiae of the epidermal and dermal surfaces showed that: (1) both surfaces maintained the patterns and characteristics of fingerprints (arch, whorl or loop) and the characteristics related to the systems and the disposal of the lines, meaning the formation or not of deltas; (2) the total number of marked minutiae did not differ between both surfaces for the group of individuals (paired t test, p=0.48); (3) the percentage of coincidences and divergences (minutiae present on only one surface) between minutiae were 63.0±20.0% and 37.0±20.0%, respectively; (4) identification was possible for 16 fingers/individuals, but not for 3 of them; (5) the increase in the number of marked minutiae does not affect the percentage of coincidences. Our results demonstrate the feasibility of the dermal surface for identification purposes due to the high percentage of matching minutiae, but considering the discrepancies and the inconclusive identification of 3 fingers/individuals, our study points to the use of more fingers per individual, as well as the possibility of further studies to improve on the techniques for increasing the identification of corpses, or even to deploy new technologies to ensure their rapid and safe identification. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

SCAMPI Lead Appraiser (Service Mark) Body of Knowledge (SLA BOK)

DTIC Science & Technology

2007-10-01

CMP 6.4.2, Understanding business goals and concerns as they impact process judgments • CMP 6.5.4, Recommending next steps for process improvement...Applying practice characterization and rating rules CMP 6.4.2 Understanding business goals and concerns as they impact process judgments Associated...judgments CMP 6.4.2* Understanding business goals and concerns as they impact process judgments CMP 6.4.3 Conducting preliminary findings

An investigation into the impact of question structure on the performance of first year physics undergraduate students at the University of Cambridge

NASA Astrophysics Data System (ADS)

Gibson, Valerie; Jardine-Wright, Lisa; Bateman, Elizabeth

2015-07-01

We describe a study of the impact of exam question structure on the performance of first year Natural Sciences physics undergraduates from the University of Cambridge. The results show conclusively that a student’s performance improves when questions are scaffolded compared with university style questions. In a group of 77 female students we observe that the average exam mark increases by 13.4% for scaffolded questions, which corresponds to a 4.9 standard deviation effect. The equivalent observation for 236 male students is 9% (5.5 standard deviations). We also observe a correlation between exam performance and A2-level marks for UK students, and that students who receive their school education overseas, in a mixed gender environment, or at an independent school are more likely to receive a first class mark in the exam. These results suggest a mis-match between the problem-solving skills and assessment procedures between school and first year university and will provide key input into the future teaching and assessment of first year undergraduate physics students.

Simulating the Response of a Composite Honeycomb Energy Absorber. Part 2; Full-Scale Impact Testing

NASA Technical Reports Server (NTRS)

Fasanella, Edwin L.; Annett, Martin S.; Jackson, Karen E.; Polanco, Michael A.

2012-01-01

NASA has sponsored research to evaluate an externally deployable composite honeycomb designed to attenuate loads in the event of a helicopter crash. The concept, designated the Deployable Energy Absorber (DEA), is an expandable Kevlar(Registered TradeMark) honeycomb. The DEA has a flexible hinge that allows the honeycomb to be stowed collapsed until needed during an emergency. Evaluation of the DEA began with material characterization of the Kevlar(Registered TradeMark)-129 fabric/epoxy, and ended with a full-scale crash test of a retrofitted MD-500 helicopter. During each evaluation phase, finite element models of the test articles were developed and simulations were performed using the dynamic finite element code, LS-DYNA(Registered TradeMark). The paper will focus on simulations of two full-scale impact tests involving the DEA, a mass-simulator and a full-scale crash of an instrumented MD-500 helicopter. Isotropic (MAT24) and composite (MAT58) material models, which were assigned to DEA shell elements, were compared. Based on simulations results, the MAT58 model showed better agreement with test.

The Impact of Salinity on the Seasonal and Interannual Variability of the Upper Ocean Structure and Air/Sea Interaction in the South Eastern Tropical Indian Ocean

NASA Astrophysics Data System (ADS)

Soares, S. M.; Richards, K. J.; Annamalai, H.; Natarov, A.

2016-02-01

The Seychelles-Chagos thermocline ridge (SCRT) in the south-eastern tropical Indian Ocean is believed to play an important role on air/sea interactions at monsoonal and intraseasonal timescales. Large gains in predictability of monsoon and intraseasonal variability may result from studying the mechanisms of ocean feedback to the atmosphere in the SCRT region. ARGO data from 2005-2014 show a marked salinity and temperature annual cycle, where mixed layer waters are freshest and warmest around February-March and saltiest and coldest around July-August in the eastern side of the SCRT. An analysis of the mixed-layer salt budget using a mix of observational gridded products and a coupled model shows that: i) surface freshwater fluxes do not play a significant role on the SCRT salinity annual cycle, ii) the freshening during austral Spring is primarily driven by zonal advection of the large pool of less saline waters off the coast of southeast Asia and bay of Bengal, while meridional advection accounts for a large fraction of the salting during Fall. The largest interannual anomalies in the ARGO salinity record occur in the aftermath of the negative Indian Ocean Dipole events of 2005 and 2010, when February mixed layer freshening was much reduced. The appearance of the fresher waters were evident in the DYNAMO/CINDY data collected in the area during Spring 2011 following the passage of a downwelling Rossby wave. Lagrangian parcel tracking indicates a variety of sources for these fresher waters, but generally agrees with the ARGO results above. The fresh surface layer had a significant impact on the measured turbulence and mixing and may have impacted the development of Madden-Julien Oscillation events observed during DYNAMO/CINDY. Given these findings, we examine in detail the suite of DYNAMO observations, combining them with numerical modeling experiments to determine the role of eddy fluxes and vertical processes on the formation of these freshwater layers, as well as their influence on the surface heat budget and possible feedbacks on air-sea interactions.

Spherule Beds 3.47-3.24 Billion Years Old in the Barberton Greenstone Belt, South Africa: A Record of Large Meteorite Impacts and Their Influence on Early Crustal and Biological Evolution

NASA Technical Reports Server (NTRS)

Lowe, Donald R.; Byerly, Gary R.; Kyte, Frank T.; Shukolyukov, Alexander; Asaro, Frank; Krull, Alexander

2003-01-01

Four layers, S1-S4, containing sand-sized spherical particles formed as a result of large meteorite impacts, occur in 3.47-3.24 Ga rocks of the Barberton Greenstone Belt, South Africa. Ir levels in S3 and S4 locally equal or exceed chondritic values but in other sections are at or only slightly above background. Most spherules are inferred to have formed by condensation of impact-produced rock vapor clouds, although some may represent ballistically ejected liquid droplets. Extreme Ir abundances and heterogeneity may reflect element fractionation during spherule formation, hydraulic fractionation during deposition, and/or diagenetic and metasomatic processes. Deposition of S1, S2, and S3 was widely influenced by waves and/or currents interpreted to represent impact-generated tsunamis, and S1 and S2 show multiple graded layers indicating the passage of two or more wave trains. These tsunamis may have promoted mixing within a globally stratified ocean, enriching surface waters in nutrients for biological communities. S2 and S3 mark the transition from the 300-million-year-long Onverwacht stage of predominantly basaltic and komatiitic volcanism to the late orogenic stage of greenstone belt evolution, suggesting that regional and possibly global tectonic reorganization resulted from these large impacts. These beds provide the oldest known direct record of terrestrial impacts and an opportunity to explore their influence on early life, crust, ocean, and atmosphere. The apparent presence of impact clusters at 3.26-3.24 Ga and approx. 2.65-2.5 Ga suggests either spikes in impact rates during the Archean or that the entire Archean was characterized by terrestrial impact rates above those currently estimated from the lunar cratering record.

Spherule beds 3.47-3.24 billion years old in the Barberton Greenstone Belt, South Africa: a record of large meteorite impacts and their influence on early crustal and biological evolution.

PubMed

Lowe, Donald R; Byerly, Gary R; Kyte, Frank T; Shukolyukov, Alexander; Asaro, Frank; Krull, Alexandra

2003-01-01

Four layers, S1-S4, containing sand-sized spherical particles formed as a result of large meteorite impacts, occur in 3.47-3.24 Ga rocks of the Barberton Greenstone Belt, South Africa. Ir levels in S3 and S4 locally equal or exceed chondritic values but in other sections are at or only slightly above background. Most spherules are inferred to have formed by condensation of impact-produced rock vapor clouds, although some may represent ballistically ejected liquid droplets. Extreme Ir abundances and heterogeneity may reflect element fractionation during spherule formation, hydraulic fractionation during deposition, and/or diagenetic and metasomatic processes. Deposition of S1, S2, and S3 was widely influenced by waves and/or currents interpreted to represent impact-generated tsunamis, and S1 and S2 show multiple graded layers indicating the passage of two or more wave trains. These tsunamis may have promoted mixing within a globally stratified ocean, enriching surface waters in nutrients for biological communities. S2 and S3 mark the transition from the 300-million-year-long Onverwacht stage of predominantly basaltic and komatiitic volcanism to the late orogenic stage of greenstone belt evolution, suggesting that regional and possibly global tectonic reorganization resulted from these large impacts. These beds provide the oldest known direct record of terrestrial impacts and an opportunity to explore their influence on early life, crust, ocean, and atmosphere. The apparent presence of impact clusters at 3.26-3.24 Ga and approximately 2.65-2.5 Ga suggests either spikes in impact rates during the Archean or that the entire Archean was characterized by terrestrial impact rates above those currently estimated from the lunar cratering record.

Tribological properties of surfaces

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1978-01-01

The real area of contact between two solid surfaces is only a small portion of the apparent area. Deformation of these areas can result in solid state contact through surface films. For clean solid to solid contact strong adhesive bonding occurs across the interface. Under these conditions many properties of the solid such as the metallurgical and chemical nature of metals can influence adhesion, friction, and wear behavior. The presence of gases, liquids, and solid films on the surface of solids alter markedly tribological characteristics. These surface films can also considerably change the mechanical effects of solid state contact on bulk material behavior.

Handheld Lasers Allow Efficient Detection of Fluorescent Marked Organisms in the Field

PubMed Central

Fleischer, Shelby J.; De Moraes, Consuelo M.; Mescher, Mark C.; Tooker, John F.

2015-01-01

Marking organisms with fluorescent dyes and powders is a common technique used in ecological field studies that monitor movement of organisms to examine life history traits, behaviors, and population dynamics. External fluorescent marking is relatively inexpensive and can be readily employed to quickly mark large numbers of individuals; however, the ability to detect marked organisms in the field at night has been hampered by the limited detection distances provided by portable fluorescent ultraviolet lamps. In recent years, significant advances in LED lamp and laser technology have led to development of powerful, low-cost ultraviolet light sources. In this study, we evaluate the potential of these new technologies to improve detection of fluorescent-marked organisms in the field and to create new possibilities for tracking marked organisms in visually challenging environments such as tree canopies and aquatic habitats. Using handheld lasers, we document a method that provides a fivefold increase in detection distance over previously available technologies. This method allows easy scouting of tree canopies (from the ground), as well as shallow aquatic systems. This novel detection method for fluorescent-marked organisms thus promises to significantly enhance the use of fluorescent marking as a non-destructive technique for tracking organisms in natural environments, facilitating field studies that aim to document otherwise inaccessible aspects of the movement, behavior, and population dynamics of study organisms, including species with significant economic impacts or relevance for ecology and human health. PMID:26035303

Glacier mass balance and its potential impacts in the Altai Mountains over the period 1990-2011

NASA Astrophysics Data System (ADS)

Zhang, Yong; Enomoto, Hiroyuki; Ohata, Tetsuo; Kitabata, Hideyuki; Kadota, Tsutomu; Hirabayashi, Yukiko

2017-10-01

The Altai Mountains contain 1281 glaciers covering an area of 1191 km2. These glaciers have undergone significant changes in glacial length and area over the past decade. However, mass changes of these glaciers and their impacts remain poorly understood. Here we present surface mass balances of all glaciers in the region for the period 1990-2011, using a glacier mass-balance model forced by the outputs of a regional climate model. Our results indicate that the mean specific mass balance for the whole region is about -0.69 m w.e. yr-1 over the entire period, and about 81.3% of these glaciers experience negative net mass balance. We detect an accelerated wastage of these glaciers in recent years, and marked differences in mass change and its sensitivity to climate change for different regions and size classes. In particular, higher mass loss and temperature sensitivity are observed for glaciers smaller than 0.5 km2. In addition to temperature rise, a decrease in precipitation in the western part of the region and an increase in precipitation in the eastern part likely contribute to significant sub-region differences in mass loss. With significant glacier wastage, the contribution of all glaciers to regional water resources and sea-level change becomes larger than before, but may not be a potential threat to human populations through impacts on water availability.

Assessing the impact of a nurse-delivered home dried blood spot service on uptake of testing for household contacts of hepatitis B-infected pregnant women across two London trusts.

PubMed

Keel, P; Edwards, G; Flood, J; Nixon, G; Beebeejaun, K; Shute, J; Poh, J; Millar, A; Ijaz, S; Parry, J; Mandal, S; Ramsay, M; Amirthalingam, G

2016-07-01

Despite national guidance recommending testing and vaccination of household contacts of hepatitis B-infected pregnant women, provision and uptake of this is sub-optimal. The aim of this study was to evaluate the use of in-home dried blood spot (DBS) testing to increase testing and vaccination of household contacts of hepatitis B-infected pregnant women as an alternative approach to conventional primary-care follow-up. The study was conducted across two London maternity trusts (North Middlesex and Newham). All hepatitis B surface antigen-positive pregnant women identified through these trusts were eligible for inclusion. The intervention of in-home DBS testing for household contacts was introduced at North Middlesex Trust from November 2010 to December 2011. Data on testing and vaccination uptake from GP records across the two trusts were compared between baseline (2009) and intervention (2010-2011) periods. In-home DBS service increased testing uptake for all ages (P < 0·001) with the biggest impact seen in partners, where testing increased from 30·3% during the baseline period to 96·6% during the intervention period in North Middlesex Trust. Although impact on vaccine uptake was less marked, improvements were observed for adults. The provision of nurse-led home-based DBS may be useful in areas of high prevalence.

Cross-Grain Knife Planing Improves Surface Quality and Utilization of Aspen

Treesearch

Harold A. Stewart

1971-01-01

Aspen at 6 percent moisture content was planed parallel to the grain and across the grain on a cabinet planer with a 25? rake angle, 1/16- and 1/32-inch depth of cut, and 20 knife marks per inch. Aspen was also cross-grain knife planed with a 45? rake angle, 1/32-, 1/16-, and 1/8-inch depths of cut, and 20, 10, 5, and 2.5 knife marks per inch. Cross-grain knife...

An Investigation of the Hot Corrosion Protectivity Behavior of Platinum Modified Aluminide Coatings on Nickel-Based Superalloys

DTIC Science & Technology

1987-03-01

is unlimited. WCRT LAIISIPIcaiIo IP THIS P431 IEPORT DOCUMENTATION PAGE* is REIPOT SECURilY CLASSIFICATION 1b RISTRtC7IVI MARKINGS la FURITY... grow until it forms a continuous surface layer. At this point, there is a parabolic decrease in the rate of oxidation and the surface stabilizes. If...surface as PtA1 2 and Pt 2 A13. Consequently, the platinum concentration gradient that develops is highest at the surface, but, rapidly diminishes as the

Multiplexing clonality: combining RGB marking and genetic barcoding

PubMed Central

Cornils, Kerstin; Thielecke, Lars; Hüser, Svenja; Forgber, Michael; Thomaschewski, Michael; Kleist, Nadja; Hussein, Kais; Riecken, Kristoffer; Volz, Tassilo; Gerdes, Sebastian; Glauche, Ingmar; Dahl, Andreas; Dandri, Maura; Roeder, Ingo; Fehse, Boris

2014-01-01

RGB marking and DNA barcoding are two cutting-edge technologies in the field of clonal cell marking. To combine the virtues of both approaches, we equipped LeGO vectors encoding red, green or blue fluorescent proteins with complex DNA barcodes carrying color-specific signatures. For these vectors, we generated highly complex plasmid libraries that were used for the production of barcoded lentiviral vector particles. In proof-of-principle experiments, we used barcoded vectors for RGB marking of cell lines and primary murine hepatocytes. We applied single-cell polymerase chain reaction to decipher barcode signatures of individual RGB-marked cells expressing defined color hues. This enabled us to prove clonal identity of cells with one and the same RGB color. Also, we made use of barcoded vectors to investigate clonal development of leukemia induced by ectopic oncogene expression in murine hematopoietic cells. In conclusion, by combining RGB marking and DNA barcoding, we have established a novel technique for the unambiguous genetic marking of individual cells in the context of normal regeneration as well as malignant outgrowth. Moreover, the introduction of color-specific signatures in barcodes will facilitate studies on the impact of different variables (e.g. vector type, transgenes, culture conditions) in the context of competitive repopulation studies. PMID:24476916

Pleural Dye Marking Using Radial Endobronchial Ultrasound and Virtual Bronchoscopy before Sublobar Pulmonary Resection for Small Peripheral Nodules.

PubMed

Lachkar, Samy; Baste, Jean-Marc; Thiberville, Luc; Peillon, Christophe; Rinieri, Philippe; Piton, Nicolas; Guisier, Florian; Salaun, Mathieu

2018-01-01

Minimally invasive surgery of pulmonary nodules allows suboptimal palpation of the lung compared to open thoracotomy. The objective of this study was to assess endoscopic pleural dye marking using radial endobronchial ultrasound (r-EBUS) and virtual bronchoscopy to localize small peripheral lung nodules immediately before minimally invasive resection. The endoscopic procedure was performed without fluoroscopy, under general anesthesia in the operating room immediately before minimally invasive surgery. Then, 1 mL of methylene blue (0.5%) was instilled into the guide sheath, wedged in the subpleural space. Wedge resection or segmentectomy were guided by visualization of the dye on the pleural surface. Contribution of dye marking to the surgical procedure was rated by the surgeon. Twenty-five nodules, including 6 ground glass opacities, were resected in 22 patients by video-assisted thoracoscopic wedge resection (n = 11) or robotic-assisted thoracoscopic surgery (10 segmentectomies and 1 wedge resection). The median greatest diameter of nodules was 8 mm. No conversion to open thoracotomy was needed. The endoscopic procedure added an average 10 min to surgical resection. The dye was visible on the pleural surface in 24 cases. Histological diagnosis and free margin resection were obtained in all cases. Median skin-to-skin operating time was 90 min for robotic segmentectomy and 40 min for video-assisted wedge resection. The same operative precision was considered impossible by the surgeon without dye marking in 21 cases. Dye marking using r-EBUS and virtual bronchoscopy can be easily and safely performed to localize small pulmonary nodules immediately before minimally invasive resection. © 2018 S. Karger AG, Basel.

Electromagnetic navigational bronchoscopy with dye marking for identification of small peripheral lung nodules during minimally invasive surgical resection

PubMed Central

Muñoz-Largacha, Juan A.; Ebright, Michael I.; Litle, Virginia R.

2017-01-01

Background Identification of small peripheral lung nodules during minimally invasive resection can be challenging. Electromagnetic navigational bronchoscopy (ENB) with injection of dye to identify nodules can be performed by the surgeon immediately prior to resection. We evaluated the effectiveness of ENB with dye marking to aid minimally invasive resection. Methods Patients with peripheral pulmonary nodules underwent ENB before planned thoracoscopic or robotic-assisted thoracoscopic resection. Methylene blue was injected directly into the lesion for pleural-based lesions or peripherally for lesions deep to the pleural surface. Surgical resection was then immediately performed. Technical success was defined as identification of the dye marking within/close to the lesion with pathological confirmation after minimally invasive surgical resection. Results Seventeen patients (19 nodules) underwent ENB with dye marking followed by minimally invasive resection. Median lesion size was 9 mm (4–32 mm) and the median distance from the pleura was 9.5 mm (1–40 mm). Overall success rate was 79% (15/19). In two cases the dye was not visualized and in the remaining two there was extravasation of dye into the pleural space. There were trends favoring technical success for nodules that were larger or closer to the pleural surface. Five patients required adhesiolysis to visualize the target lesion and all were successful. There were no significant adverse events and a definitive diagnosis was ultimately accomplished in all patients. Conclusions ENB with dye marking is useful for guiding minimally invasive resection of small peripheral lung nodules. ENB can be undertaken immediately before performing resection in the operating room. This improves workflow and avoids the need for a separate localization procedure. PMID:28449489

An anatomical study comparing two surgical approaches for isolated talonavicular arthrodesis.

PubMed

Higgs, Zoe; Jamal, Bilal; Fogg, Quentin A; Kumar, C Senthil

2014-10-01

Two operative approaches are commonly used for isolated talonavicular arthrodesis: the medial and the dorsal approach. It is recognized that access to the lateral aspect of the talonavicular joint can be limited when using the medial approach, and it is our experience that using the dorsal approach addresses this issue. We performed an anatomical study using cadaver specimens, to compare the amount of articular surface that can be accessed by each operative approach. Medial and dorsal approaches to the talonavicular joint were performed on each of 11 cadaveric specimens (10 fresh frozen, 1 embalmed). Distraction of the joint was performed as used intraoperatively and the accessible area of articular surfaces was marked for each of the 2 approaches using a previously reported technique. Disarticulation was performed and the marked surface area was quantified using an immersion digital microscribe, allowing a 3-dimensional virtual model of the articular surfaces to be assessed. The median percentage of total accessible talonavicular articular surface area for the medial and dorsal approaches was 71% and 92%, respectively (Wilcoxon signed-rank test, P < .001). This study provides quantifiable measurements of the articular surface accessible by the medial and dorsal approaches to the talonavicular joint. These data support for the use of the dorsal approach for talonavicular arthrodesis, particularly in cases where access to the lateral half of the joint is necessary. © The Author(s) 2014.

Where's the Beaverhead beef?. [meteorite impact structure

NASA Technical Reports Server (NTRS)

Hargraves, R. B.

1992-01-01

Only rare quartz grains with single-set planar (1013) deformation features (PDF's) are present in breccia dikes found in association with uniformly oriented shatter cones that occur over an area 8 x 25 km. This suggests that the Beaverhead shocked rocks come from only the outer part of the central uplift of what must have been a large (greater than 100 km diameter) complex impact structure. An impact event of this magnitude on continental crust (thought to have occurred in late Precambrian or ealy Paleozoic time) could be expected to punctuate local geologic history. Furthermore, although it may now be covered, its scar should remain despite all the considerable subsequent erosion/deposition and tectonism since the impact. The following are three large-scale singularities or anomalies that may reflect the event and mark its source. (1) The Lemhi Arch is a major structural uplift that occurred in late Proterozoic-early Paleozoic time in East Central Idaho and caused the erosion of at least 4 km of sedimentary cover. This may be directly related to the impact. (2) Of the many thrust sheets comprising the Cordilleran belt, the Cabin plate that carries the shocked rocks is unique in that it alone intersected the crystalline basement. It also now marks the apex of the Southwest Montana Recess in the Sevier front. The basement uplift remaining from the impact may have constituted a mechanical obstacle to the advancing thrust sheets in Cretaceous time, causing the recess. (3) What could be interpreted as a roughly circular aeromagnetic anomaly approx. 70 km in diameter can be discerned in the state aeromagnetic map centered about 20 km southeast of Challis, Idaho, in the Lost River range. It is in approximately the right place, and ignoring the possibility that the anomalies have diverse causes and the circular pattern is coincidental, it may mark what remains of the buried central uplift structure.

Engineering Evaluation of International Low Impact Docking System Latch Hooks

NASA Technical Reports Server (NTRS)

Martinez, J.; Patin, R.; Figert, J.

2013-01-01

The international Low Impact Docking System (iLIDS) provides a structural arrangement that allows for visiting vehicles to dock with the International Space Station (ISS) (Fig 1). The iLIDS docking units are mechanically joined together by a series of active and passive latch hooks. In order to preserve docking capability at the existing Russian docking interfaces, the iLIDS latch hooks are required to conform to the existing Russian design. The latch hooks are classified as being fail-safe. Since the latch hooks are fail-safe, the hooks are not fracture critical and a fatigue based service life assessment will satisfy the structural integrity requirements. Constant amplitude fatigue testing to failure on four sets of active/passive iLIDS latch hooks was performed at load magnitudes of 10, 11, and 12 kips. Failure analysis of the hook fatigue failures identified multi-site fatigue initiation that was effectively centered about the hook mid-plane (consistent with the 3D model results). The fatigue crack initiation distribution implies that the fatigue damage accumulation effectively results in a very low aspect ratio surface crack (which can be simulated as thru-thickness crack). Fatigue damage progression resulted in numerous close proximity fatigue crack initiation sites. It was not possible to determine if fatigue crack coalescence occurs during cyclic loading or as result of the fast fracture response. The presence of multiple fatigue crack initiation sites on different planes will result in the formation of ratchet marks as the cracks coalesce. Once the stable fatigue crack becomes unstable and the fast fracture advances across the remaining ligament and the plane stress condition at a free-surface will result in failure along a 45 deg. shear plane (slant fracture) and the resulting inclined edge is called a shear lip. The hook thickness on the plane of fatigue crack initiation is 0.787". The distance between the shear lips on this plane was on the order of 0.48" and it was effectively centered about the mid-plane of the section. The numerous ratchet marks between the shear lips on the fracture initiation plane are indicative of multiple fatigue initiation sites within this region. The distribution of the fatigue damage about the centerline of the hook is consistent with the analytical results that demonstrate peak stress/strain response at the mid-plane that decreases in the direction of the hook outer surfaces. Scanning electron microscope images of the failed sections detected fatigue crack striations in close proximity to the free surface of the hook radius. These findings were documented at three locations on the fracture surface : 1) adjacent to the left shear lip, 2) adjacent to the right shear lip, and 3) near the centerline of the section. The features of the titanium fracture surface did not allow for a determination of a critical crack size via identification of the region where the fatigue crack propagation became unstable. The fracture based service life projections where benchmarked with strain-life analyses. The strainrange response in the hook radius was defined via the correlated finite element models and the modified method of universal slopes was incorporated to define the strain-life equation for the titanium alloy. The strain-life assessment confirmed that the fracture based projections were reasonable for the loading range of interest. Based upon the analysis and component level fatigue test data a preliminary service life capability for the iLIDS active and passive hooks of 2 lifetimes is projected (includes a scatter factor of 4).

The hydrological modeling in terms of determining the potential European beaver effect

NASA Astrophysics Data System (ADS)

Szostak, Marta; Jagodzińska, Jadwiga

2017-06-01

The objective of the paper was the hydrological analysis, in terms of categorizing main watercourses (based on coupled catchments) and marking areas covered by potential impact of the occurrence and activities of the European beaver Castor fiber. At the analysed area - the Forest District Głogów Małopolski there is a population of about 200 beavers in that Forest District. Damage inflicted by beavers was detected on 33.0 ha of the Forest District, while in the area of 13.9 ha the damage was small (below 10%). The monitoring of the beavers' behaviour and the analysis of their influence on hydrology of the area became an important element of using geoinformationtools in the management of forest areas. ArcHydro ArcGIS Esri module was applied, as an integrated set of tools for hydrographical analysis and modelling. Further steps of the procedure are hydrologic analyses such as: marking river networks on the DTM, filling holes, making maps of the flow direction, making the map of the accumulation flow, defining and segmentation of streams, marking elementary basins, marking coupled basins, making dams in the places, where beavers occur and localization of the area with a visible impact of damming. The result of the study includes maps prepared for the Forest District: the map of main rivers and their basins, categories of watercourses and compartments particularly threatened by beaver's foraging.

Analysis of energy flow during playground surface impacts.

PubMed

Davidson, Peter L; Wilson, Suzanne J; Chalmers, David J; Wilson, Barry D; Eager, David; McIntosh, Andrew S

2013-10-01

The amount of energy dissipated away from or returned to a child falling onto a surface will influence fracture risk but is not considered in current standards for playground impact-attenuating surfaces. A two-mass rheological computer simulation was used to model energy flow within the wrist and surface during hand impact with playground surfaces, and the potential of this approach to provide insights into such impacts and predict injury risk examined. Acceleration data collected on-site from typical playground surfaces and previously obtained data from children performing an exercise involving freefalling with a fully extended arm provided input. The model identified differences in energy flow properties between playground surfaces and two potentially harmful surface characteristics: more energy was absorbed by (work done on) the wrist during both impact and rebound on rubber surfaces than on bark, and rubber surfaces started to rebound (return energy to the wrist) while the upper limb was still moving downward. Energy flow analysis thus provides information on playground surface characteristics and the impact process, and has the potential to identify fracture risks, inform the development of safer impact-attenuating surfaces, and contribute to development of new energy-based arm fracture injury criteria and tests for use in conjunction with current methods.

Demographics, clinical disease characteristics, and quality of life in a large cohort of psoriasis patients with and without psoriatic arthritis

PubMed Central

Truong, B; Rich-Garg, N; Ehst, BD; Deodhar, AA; Ku, JH; Vakil-Gilani, K; Danve, A; Blauvelt, A

2015-01-01

Innovation What is already known about the topic: psoriasis (PsO) is a common skin disease with major impact on quality of life (QoL). Patient-reported data on QoL from large number of PsO patients with and without psoriatic arthritis (PsA) are limited. What this study adds: In a large cohort referred to a university psoriasis center, patients with PsO and concomitant PsA (~30% in this group) had greater degrees of skin and nail involvement and experienced greater negative impacts on QoL. Despite large numbers of patients with moderate-to-severe disease, use of systemic therapy by community practitioners was uncommon. Background PsO and PsA are common diseases that have marked adverse impacts on QoL. The disease features and patient-reported QoL data comparing PsO and PsA patients are limited. Objective To identify and compare demographics, clinical disease characteristics, and QoL scores in a large cohort of PsO patients with and without PsA. Methods All PsO patients seen in a psoriasis specialty clinic, named the Center of Excellence for Psoriasis and Psoriatic Arthritis, were enrolled in an observational cohort. Demographic, QoL, and clinical data were collected from patient-reported questionnaires and from physical examinations performed by Center of Excellence for Psoriasis and Psoriatic Arthritis dermatologists and a rheumatologists. Cross sectional descriptive data were collected and comparisons between patients with PsO alone and those with concomitant PsA are presented. Results A total of 568 patients were enrolled in the database. Mean age of PsO onset was 28 years and mean disease duration was 18 years. Those with family history had an earlier onset of PsO by ~7 years. Mean body surface area involvement with PsO was 14%. Mean body mass index was 30.7. Prevalence of PsA was 29.8%. PsA patients had a higher mean body surface area compared to patients with PsO alone (16.7% vs 13.4%, P<0.05), higher prevalence of psoriatic nail changes (54.4% vs 36%, P<0.0002), and worse QoL scores as assessed by the Short Form-12 (67 vs 52, P<0.00001), Psoriasis Quality of Life-12 questionnaire (62 vs 71, P<0.01), and Routine Assessment of Patient Index Data 3 (2.3 vs 4.7, P<0.01). Strikingly, 49% of patients with PsO had never received any systemic therapy. Conclusion These data highlight that PsO has marked negative impacts on QoL, while those patients with concomitant PsA are affected to a much greater degree. Despite large numbers of patients presenting with moderate-to-severe disease, use of systemic therapy for both PsO and PsA was uncommon. PMID:26622188

A reappraisal of adult thoracic and abdominal surface anatomy in Iranians in vivo using computed tomography.

PubMed

Pak, Neda; Patel, Shilpan G; Hashemi Taheri, Amir P; Hashemi, Fariba; Eftekhari Vaghefi, Raana; Naybandi Atashi, Sara; Mirjalili, S Ali

2016-03-01

Surface anatomy is a core component of human anatomy in clinical practice. It allows clinicians to assess patients accurately and quickly; however, recent studies have revealed variability among individuals and ethnicities. The aim of this study is to investigate possible variations in adult thoracic and abdominal surface anatomy landmarks in an Iranian population. This study used 100 thoracoabdominal CT scans (mean age: 47 ± 17 years, age range: 20-77 years, 47% females), noted the most common locations of clinically relevant surface markings, and analyzed correlations between these variables and age or gender. While many common surface markings in Iranians were consistent with the evidence-based literature, there were some differences. In relation to the corresponding segments of the vertebral column, the superior vena cava formation and the lower border of the pleura adjacent to the vertebral column and right kidney tended to be at higher levels in adult Iranians than a Caucasian population. There were also discrepancies between the Iranian population and commonly-referenced medical textbooks and recent evidence-based literature concerning the vertebral levels of the diaphragmatic openings of the esophagus, aorta, and inferior vena cava. This study emphasizes the need to consider evidence-based reappraisals of surface anatomy to guide clinical practice. Much of our current knowledge of surface anatomy is based on older studies of cadavers rather than living people, and does not take ethnic and individual variations into consideration. © 2015 Wiley Periodicals, Inc.

Surface magnetism in a chiral d -wave superconductor with hexagonal symmetry

NASA Astrophysics Data System (ADS)

Goryo, Jun; Imai, Yoshiki; Rui, W. B.; Sigrist, Manfred; Schnyder, Andreas P.

2017-10-01

Surface properties are examined in a chiral d -wave superconductor with hexagonal symmetry, whose one-body Hamiltonian possesses intrinsic spin-orbit coupling identical to the one characterizing the topological nature of the Kane-Mele honeycomb insulator. In the normal state, spin-orbit coupling gives rise to spontaneous surface spin currents, whereas in the superconducting state, besides the spin currents, there exist also charge surface currents, due to chiral pairing symmetry. Interestingly, the combination of these two currents results in a surface spin polarization, whose spatial dependence is markedly different on the zigzag and armchair surfaces. We discuss various potential candidate materials, such as SrPtAs, which may exhibit these surface properties.

Versatile infrared refractive-index sensor based on surface plasmon resonance in graphene sheet

NASA Astrophysics Data System (ADS)

Bai, Yukun; Wang, Biao; Ma, Xiurong

2018-03-01

A reflection-type refractive-index sensor based on the surface plasmon resonance of graphene in the mid-infrared to terahertz regime is proposed. With a simple configuration, the sensor demonstrates high flexibilities for the gas and liquid samples sensing and achieves markedly improved figures of merit of 53.64 and 36.5 RIU - 1, respectively.

Impact of the springtime Himalayan-Tibetan Plateau on the onset on the Indian summer monsoon in coupled forecasts

NASA Astrophysics Data System (ADS)

Orsolini, Yvan; Senan, Retish; Weisheimer, Antje; Vitart, Frederic; Balsamo, Gianpaolo; Doblas-Reyes, Francisco; Stockdale, Timothy; Dutra, Emanuel

2016-04-01

The springtime snowpack over the Himalayan-Tibetan Plateau (HTP) region has long been suggested to be an influential factor on the onset of the Indian summer monsoon. In the frame of the SPECS project, we have assessed the impact of realistic snow initialization in springtime over HTP on the onset of the Indian summer monsoon. We examine a suite of coupled ocean-atmosphere 4-month ensemble reforecasts made at the European Centre for Medium-Range Weather Forecasts (ECMWF), using the Seasonal Forecasting System 4. The reforecasts were initialized on 1 April every year for the period 1981-2010. In these seasonal reforecasts, the snow is initialized "realistically" with ERA-Interim/Land Reanalysis. In addition, we carried out an additional set of forecasts, identical in all aspects except that initial conditions for snow-related land surface variables over the HTP region are randomized. We show that high snow depth over HTP influences the meridional tropospheric temperature gradient reversal that marks the monsoon onset. Composite difference based on a normalized HTP snow index reveal that, in high snow years, (i) the onset is delayed by about 8 days, and (ii) negative precipitation anomalies and warm surface conditions prevail over India. We show that about half of this delay can be attributed to the realistic initialization of snow over the HTP region. We further demonstrate that high April snow depths over HTP are not uniquely influenced by either the El Nino-Southern Oscillation, the Indian Ocean Dipole or the North Atlantic Oscillation.

CO2 Jets and Wind Patterns on Mars

NASA Astrophysics Data System (ADS)

Hatcher, Chase; Aye, K.-Michael; Portyankina, Ganna

2017-10-01

In Martian winters, the poles get covered by a layer of transparent CO2 ice. In spring, sunlight causes substrate under the ice to heat up which sublimates CO2 under the ice. The accumulating gas eventually causes the ice above it to rupture and the CO2 and substrate mixture spews out like a geyser and settles back down on the surface. The shape, size, and alignment of the deposits on the surface as viewed by the HiRISE camera are related to physical processes like sublimation, weather, and wind on Mars. The jet deposits are identified by citizen scientists on a website called Planet Four. Users are shown sections of HiRISE images and asked to mark different surface features with different tools. The markings are averaged, filtered, and sorted to ensure that the data accurately represents the images. By analyzing trends in the change of different characteristics of these surface features over time, we conclude that different regions on Mars have different sublimation processes and different wind patterns. We also conclude that wind and weather patterns generally repeat from year to year, and that sediment deposits affect local weather as well.

A novel semi-quantitative method for measuring tissue bleeding.

PubMed

Vukcevic, G; Volarevic, V; Raicevic, S; Tanaskovic, I; Milicic, B; Vulovic, T; Arsenijevic, S

2014-03-01

In this study, we describe a new semi-quantitative method for measuring the extent of bleeding in pathohistological tissue samples. To test our novel method, we recruited 120 female patients in their first trimester of pregnancy and divided them into three groups of 40. Group I was the control group, in which no dilation was applied. Group II was an experimental group, in which dilation was performed using classical mechanical dilators. Group III was also an experimental group, in which dilation was performed using a hydraulic dilator. Tissue samples were taken from the patients' cervical canals using a Novak's probe via energetic single-step curettage prior to any dilation in Group I and after dilation in Groups II and III. After the tissue samples were prepared, light microscopy was used to obtain microphotographs at 100x magnification. The surfaces affected by bleeding were measured in the microphotographs using the Autodesk AutoCAD 2009 program and its "polylines" function. The lines were used to mark the area around the entire sample (marked A) and to create "polyline" areas around each bleeding area on the sample (marked B). The percentage of the total area affected by bleeding was calculated using the formula: N = Bt x 100 / At where N is the percentage (%) of the tissue sample surface affected by bleeding, At (A total) is the sum of the surfaces of all of the tissue samples and Bt (B total) is the sum of all the surfaces affected by bleeding in all of the tissue samples. This novel semi-quantitative method utilizes the Autodesk AutoCAD 2009 program, which is simple to use and widely available, thereby offering a new, objective and precise approach to estimate the extent of bleeding in tissue samples.

Effect of limbal marking prior to laser ablation on the magnitude of cyclotorsional error.

PubMed

Chen, Xiangjun; Stojanovic, Aleksandar; Stojanovic, Filip; Eidet, Jon Roger; Raeder, Sten; Øritsland, Haakon; Utheim, Tor Paaske

2012-05-01

To evaluate the residual registration error after limbal-marking-based manual adjustment in cyclotorsional tracker-controlled laser refractive surgery. Two hundred eyes undergoing custom surface ablation with the iVIS Suite (iVIS Technologies) were divided into limbal marked (marked) and non-limbal marked (unmarked) groups. Iris registration information was acquired preoperatively from all eyes. Preoperatively, the horizontal axis was recorded in the marked group for use in manual cyclotorsional alignment prior to surgical iris registration. During iris registration, the preoperative iris information was compared to the eye-tracker captured image. The magnitudes of the registration error angle and cyclotorsional movement during the subsequent laser ablation were recorded and analyzed. Mean magnitude of registration error angle (absolute value) was 1.82°±1.31° (range: 0.00° to 5.50°) and 2.90°±2.40° (range: 0.00° to 13.50°) for the marked and unmarked groups, respectively (P<.001). Mean magnitude of cyclotorsional movement during the laser ablation (absolute value) was 1.15°±1.34° (range: 0.00° to 7.00°) and 0.68°±0.97° (range: 0.00° to 6.00°) for the marked and unmarked groups, respectively (P=.005). Forty-six percent and 60% of eyes had registration error >2°, whereas 22% and 20% of eyes had cyclotorsional movement during ablation >2° in the marked and unmarked groups, respectively. Limbal-marking-based manual alignment prior to laser ablation significantly reduced cyclotorsional registration error. However, residual registration misalignment and cyclotorsional movements remained during ablation. Copyright 2012, SLACK Incorporated.

Visualization of permanent marks in progressive addition lenses by digital in-line holography

NASA Astrophysics Data System (ADS)

Perucho, Beatriz; Micó, Vicente

2013-04-01

A critical issue in the production of ophthalmic lenses is to guarantee the correct centering and alignment throughout the manufacturing and mounting processes. Aimed to that, progressive addition lenses (PALs) incorporate permanent marks at standardized locations at the lens. Those marks are engraved upon the surface and provide the model identification and addition power of the PAL, as well as to serve as locator marks to re-ink the removable marks again if necessary. Although the permanent marks should be visible by simple visual inspection, those marks are often faint and weak on new lenses providing low contrast, obscured by scratches on older lenses, and partially occluded and difficult to recognize on tinted or anti-reflection coated lenses. In this contribution, we present an extremely simple visualization system for permanent marks in PALs based on digital in-line holography. Light emitted by a superluminescent diode (SLD) is used to illuminate the PAL which is placed just before a digital (CCD) sensor. Thus, the CCD records an in-line hologram incoming from the diffracted wavefront provided by the PAL. As a result, it is possible to recover an in-focus image of the PAL inspected region by means of classical holographic tools applied in the digital domain. This numerical process involves digital recording of the in-line hologram, numerical back propagation to the PAL plane, and some digital processing to reduce noise and present a high quality final image. Preliminary experimental results are provided showing the applicability of the proposed method.

Detection of Road Markings Recorded in In-Vehicle Camera Images by Using Position-Dependent Classifiers

NASA Astrophysics Data System (ADS)

Noda, Masafumi; Takahashi, Tomokazu; Deguchi, Daisuke; Ide, Ichiro; Murase, Hiroshi; Kojima, Yoshiko; Naito, Takashi

In this study, we propose a method for detecting road markings recorded in an image captured by an in-vehicle camera by using a position-dependent classifier. Road markings are symbols painted on the road surface that help in preventing traffic accidents and in ensuring traffic smooth. Therefore, driver support systems for detecting road markings, such as a system that provides warning in the case when traffic signs are overlooked, and supporting the stopping of a vehicle are required. It is difficult to detect road markings because their appearance changes with the actual traffic conditions, e. g. the shape and resolution change. The variation in these appearances depend on the positional relation between the vehicle and the road markings, and on the vehicle posture. Although these variations are quite large in an entire image, they are relatively small in a local area of the image. Therefore, we try to improve the detection performance by taking into account the local variations in these appearances. We propose a method in which a position-dependent classifier is used to detect road markings recorded in images captured by an in-vehicle camera. Further, to train the classifier efficiently, we propose a generative learning method that takes into consideration the positional relation between the vehicle and road markings, and also the vehicle posture. Experimental results showed that the detection performance when the proposed method was used was better than when a method involving a single classifier was used.

Effects of drought on birds and riparian vegetation in the Colorado River Delta, Mexico

USGS Publications Warehouse

Hinojosa-Huerta, Osvel; Nagler, Pamela L.; Carrillo-Guererro, Yamilett K.; Glenn, Edward P.

2013-01-01

The riparian corridor in the delta of the Colorado River in Mexico supports internationally important bird habitat. The vegetation is maintained by surface flows from the U.S. and Mexico and by a high, non-saline aquifer into which the dominant phreatophytic shrubs and trees are rooted. We studied the effects of a regional drought on riparian vegetation and avian abundance and diversity from 2002 to 2007, during which time surface flows were markedly reduced compared to the period from 1995 to 2002. Reduced surface flows led to a reduction in native tree cover but an increase in shrub cover, mostly due to an increase in Tamarix spp., an introduced halophytic shrub, and a reduction in Populus fremontii and Salix gooddingii trees. However, overall vegetation cover was unchanged at about 70%. Overall bird density and diversity were also unchanged, but riparian-obligate species tended to decrease in abundance, and generalist species increased. Although reduction in surface flows reduced habitat value and negatively impacted riparian-obligate bird species, portions of the riparian zone exhibited resilience. Surface flows are required to reduce soil salt levels and germinate new cohorts of native trees, but the main source of water supporting this ecosystem is the aquifer, derived from underflows from irrigated fields in the U.S. and Mexico. The long-term prospects for delta riparian habitats are uncertain due to expected reduced flows of river water from climate change, and land use practices that will reduce underflows to the riparian aquifer and increase salinity levels. Active restoration programs would be needed if these habitats are to be preserved for the future.

Tropospheric ozonesonde profiles at long-term U.S. monitoring sites: 2. Links between Trinidad Head, CA, profile clusters and inland surface ozone measurements

PubMed Central

Stauffer, Ryan M.; Thompson, Anne M.; Oltmans, Samuel J.; Johnson, Bryan J.

2018-01-01

Much attention has been focused on the transport of ozone (O3) to the Western U.S., particularly given the latest revision of the National Ambient Air Quality Standard (NAAQS) to 70 parts per billion by volume (ppbv) of O3. This makes defining a “background” O3 amount essential so that the effects of stratosphere-to-troposphere exchange and pollution transport to this region can be quantified. To evaluate free-tropospheric and surface O3 in the Western U.S., we use self-organizing maps to cluster 18 years of ozonesonde profiles (940 samples) from Trinidad Head, CA. Two of nine O3 mixing ratio profile clusters exhibit thin laminae of high O3 above Trinidad Head. A third, consisting of background (~20 – 40 ppbv) O3, occurs in ~10% of profiles. The high O3 layers are located between 1 and 4 km amsl, and reside above a subsidence inversion associated with a northern location of the semi-permanent Pacific subtropical high. Several ancillary data sets are examined to identify the high O3 sources (reanalyses, trajectories, remotely-sensed carbon monoxide), but distinguishing chemical and stratospheric influences of the elevated O3 is difficult. There is marked and long-lasting impact of the elevated tropospheric O3 on high-altitude surface O3 monitors at Lassen Volcanic and Yosemite National Parks, and Truckee, CA. Days corresponding to the high O3 clusters exhibit hourly surface O3 anomalies of +5 – 10 ppbv compared to a climatology; the anomalies can last up to four days. The profile and surface O3 links demonstrate the importance of regular ozonesonde profiling at Trinidad Head. PMID:29619290

Tropospheric Ozonesonde Profiles at Long-Term U.S. Monitoring Sites: 2. Links Between Trinidad Head, CA, Profile Clusters and Inland Surface Ozone Measurements

NASA Technical Reports Server (NTRS)

Stauffer, Ryan M.; Thompson, Anne M.; Oltmans, Samuel J.; Johnson, Bryan J.

2017-01-01

Much attention has been focused on the transport of ozone (O3) to the Western U.S., particularly given the latest revision of the National Ambient Air Quality Standard (NAAQS) to 70 parts per billion by volume (ppbv) of O3. This makes defining a 'background' O3 amount essential so that the effects of stratosphere-to-troposphere exchange and pollution transport to this region can be quantified. To evaluate free-tropospheric and surface O3 in the Western U.S., we use self-organizing maps to cluster 18 years of ozonesonde profiles (940 samples) from Trinidad Head, CA. Two of nine O3 mixing ratio profile clusters exhibit thin laminae of high O3 above Trinidad Head. A third, consisting of background (approximately 20 - 40 ppbv) O3, occurs in approximately 10 of profiles. The high O3 layers are located between 1 and 4 km amsl, and reside above a subsidence inversion associated with a northern location of the semi-permanent Pacific subtropical high. Several ancillary data sets are examined to identify the high O3 sources (reanalyses, trajectories, remotely-sensed carbon monoxide), but distinguishing chemical and stratospheric influences of the elevated O3 is difficult. There is marked and long-lasting impact of the elevated tropospheric O3 on high-altitude surface O3 monitors at Lassen Volcanic and Yosemite National Parks, and Truckee, CA. Days corresponding to the high O3 clusters exhibit hourly surface O3 anomalies of +5 - 10 ppbv compared to a climatology; the anomalies can last up to four days. The profile and surface O3 links demonstrate the importance of regular ozonesonde profiling at Trinidad Head.

Tropospheric ozonesonde profiles at long-term U.S. monitoring sites: 2. Links between Trinidad Head, CA, profile clusters and inland surface ozone measurements.

PubMed

Stauffer, Ryan M; Thompson, Anne M; Oltmans, Samuel J; Johnson, Bryan J

2017-01-27

Much attention has been focused on the transport of ozone (O 3 ) to the Western U.S., particularly given the latest revision of the National Ambient Air Quality Standard (NAAQS) to 70 parts per billion by volume (ppbv) of O 3 . This makes defining a "background" O 3 amount essential so that the effects of stratosphere-to-troposphere exchange and pollution transport to this region can be quantified. To evaluate free-tropospheric and surface O 3 in the Western U.S., we use self-organizing maps to cluster 18 years of ozonesonde profiles (940 samples) from Trinidad Head, CA. Two of nine O 3 mixing ratio profile clusters exhibit thin laminae of high O 3 above Trinidad Head. A third, consisting of background (~20 - 40 ppbv) O 3 , occurs in ~10% of profiles. The high O 3 layers are located between 1 and 4 km amsl, and reside above a subsidence inversion associated with a northern location of the semi-permanent Pacific subtropical high. Several ancillary data sets are examined to identify the high O 3 sources (reanalyses, trajectories, remotely-sensed carbon monoxide), but distinguishing chemical and stratospheric influences of the elevated O 3 is difficult. There is marked and long-lasting impact of the elevated tropospheric O 3 on high-altitude surface O 3 monitors at Lassen Volcanic and Yosemite National Parks, and Truckee, CA. Days corresponding to the high O 3 clusters exhibit hourly surface O 3 anomalies of +5 - 10 ppbv compared to a climatology; the anomalies can last up to four days. The profile and surface O 3 links demonstrate the importance of regular ozonesonde profiling at Trinidad Head.

Dissecting Stages of Human Kidney Development and Tumorigenesis with Surface Markers Affords Simple Prospective Purification of Nephron Stem Cells.

PubMed

Pode-Shakked, Naomi; Pleniceanu, Oren; Gershon, Rotem; Shukrun, Rachel; Kanter, Itamar; Bucris, Efrat; Pode-Shakked, Ben; Tam, Gal; Tam, Hadar; Caspi, Revital; Pri-Chen, Sara; Vax, Einav; Katz, Guy; Omer, Dorit; Harari-Steinberg, Orit; Kalisky, Tomer; Dekel, Benjamin

2016-03-29

When assembling a nephron during development a multipotent stem cell pool becomes restricted as differentiation ensues. A faulty differentiation arrest in this process leads to transformation and initiation of a Wilms' tumor. Mapping these transitions with respective surface markers affords accessibility to specific cell subpopulations. NCAM1 and CD133 have been previously suggested to mark human renal progenitor populations. Herein, using cell sorting, RNA sequencing, in vitro studies with serum-free media and in vivo xenotransplantation we demonstrate a sequential map that links human kidney development and tumorigenesis; In nephrogenesis, NCAM1(+)CD133(-) marks SIX2(+) multipotent renal stem cells transiting to NCAM1(+)CD133(+) differentiating segment-specific SIX2(-) epithelial progenitors and NCAM1(-)CD133(+) differentiated nephron cells. In tumorigenesis, NCAM1(+)CD133(-) marks SIX2(+) blastema that includes the ALDH1(+) WT cancer stem/initiating cells, while NCAM1(+)CD133(+) and NCAM1(-)CD133(+) specifying early and late epithelial differentiation, are severely restricted in tumor initiation capacity and tumor self-renewal. Thus, negative selection for CD133 is required for defining NCAM1(+) nephron stem cells in normal and malignant nephrogenesis.

Radiochemical analyses of surface water from U.S. Geological Survey hydrologic bench-mark stations

USGS Publications Warehouse

Janzer, V.J.; Saindon, L.G.

1972-01-01

The U.S. Geological Survey's program for collecting and analyzing surface-water samples for radiochemical constituents at hydrologic bench-mark stations is described. Analytical methods used during the study are described briefly and data obtained from 55 of the network stations in the United States during the period from 1967 to 1971 are given in tabular form.Concentration values are reported for dissolved uranium, radium, gross alpha and gross beta radioactivity. Values are also given for suspended gross alpha radioactivity in terms of natural uranium. Suspended gross beta radioactivity is expressed both as the equilibrium mixture of strontium-90/yttrium-90 and as cesium-137.Other physical parameters reported which describe the samples include the concentrations of dissolved and suspended solids, the water temperature and stream discharge at the time of the sample collection.

Atomic Force Microscope (AFM) measurements and analysis on Sagem 05R0025 secondary substrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soufli, R; Baker, S L; Robinson, J C

2006-02-22

The summary of Atomic Force Microscope (AFM) on Sagem 05R0025 secondary substrate: (1) 2 x 2 {micro}m{sup 2} and 10 x 10 {micro}m{sup 2} AFM measurements and analysis on Sagem 05R0025 secondary substrate at LLNL indicate rather uniform and extremely isotropic finish across the surface, with high-spatial frequency roughness {sigma} in the range 5.1-5.5 {angstrom} rms; (2) the marked absence of pronounced long-range polishing marks in any direction, combined with increased roughness in the very high spatial frequencies, are consistent with ion-beam polishing treatment on the surface. These observations are consistent with all earlier mirrors they measured from the samemore » vendor; and (3) all data were obtained with a Digital Instruments Dimension 5000{trademark} atomic force microscope.« less

The development of vector based 2.5D print methods for a painting machine

NASA Astrophysics Data System (ADS)

Parraman, Carinna

2013-02-01

Through recent trends in the application of digitally printed decorative finishes to products, CAD, 3D additive layer manufacturing and research in material perception, [1, 2] there is a growing interest in the accurate rendering of materials and tangible displays. Although current advances in colour management and inkjet printing has meant that users can take for granted high-quality colour and resolution in their printed images, digital methods for transferring a photographic coloured image from screen to paper is constrained by pixel count, file size, colorimetric conversion between colour spaces and the gamut limits of input and output devices. This paper considers new approaches to applying alternative colour palettes by using a vector-based approach through the application of paint mixtures, towards what could be described as a 2.5D printing method. The objective is to not apply an image to a textured surface, but where texture and colour are integral to the mark, that like a brush, delineates the contours in the image. The paper describes the difference between the way inks and paints are mixed and applied. When transcribing the fluid appearance of a brush stroke, there is a difference between a halftone printed mark and a painted mark. The issue of surface quality is significant to subjective qualities when studying the appearance of ink or paint on paper. The paper provides examples of a range of vector marks that are then transcribed into brush stokes by the painting machine.

Solid Surface Combustion Experiment

NASA Image and Video Library

1994-09-12

STS064-10-011 (12 Sept. 1994) --- The Solid Surface Combustion Experiment (SSCE), designed to supply information on flame spread over solid fuel surfaces in the reduced-gravity environment of space, is pictured during flight day four operations. The middeck experiment measured the rate of spreading, the solid-phase temperature, and the gas-phase temperature of flames spreading over rectangular fuel beds. STS-64 marked the seventh trip into space for the Lewis Research Center experiment. Photo credit: NASA or National Aeronautics and Space Administration

Density functional analysis of fluorite-structured (Ce, Zr)O 2/CeO 2 interfaces [Density functional analysis of fluorite-structured (Ce, Zr)O 2/CeO 2 interfaces: Implications for catalysis and energy applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weck, Philippe F.; Juan, Pierre -Alexandre; Dingreville, Remi

The structures and properties of Ce 1–xZr xO 2 (x = 0–1) solid solutions, selected Ce 1–xZr xO 2 surfaces, and Ce 1–xZr xO 2/CeO 2 interfaces were computed within the framework of density functional theory corrected for strong electron correlation (DFT+ U). The calculated Debye temperature increases steadily with Zr content in (Ce, Zr)O 2 phases, indicating a significant rise in microhardness from CeO 2 to ZrO 2, without appreciable loss in ductility as the interfacial stoichiometry changes. Surface energy calculations for the low-index CeO 2(111) and (110) surfaces show limited sensitivity to strong 4f-electron correlation. The fracture energymore » of Ce 1–xZr xO 2(111)/CeO 2(111) increases markedly with Zr content, with a significant decrease in energy for thicker Ce 1–xZr xO 2 films. These findings suggest the crucial role of Zr acting as a binder at the Ce 1–xZr xO 2/CeO 2 interfaces, due to the more covalent character of Zr–O bonds compared to Ce–O. Finally, the impact of surface relaxation upon interface cracking was assessed and found to reach a maximum for Ce 0.25Zr 0.75O 2/CeO 2 interfaces.« less

Mercury: Photomosaic of the Shakespeare Quadrangle (Northern Half) H-3

NASA Technical Reports Server (NTRS)

1974-01-01

This computer generated photomosaic from Mariner 10 is of the northern half of Mercury's Shakespeare Quadrangle, named for the ancient Shakespeare crater located on the lower edge to the left of center. This portion of the quadrangle covers the geographic region from 45 to 70 degrees north latitude and from 90 to 180 degrees longitude. The photomosaic was produced using computer techniques and software developed in the Image Processing Laboratory of NASA's Jet Propulsion Laboratory. The pictures have been high-pass filtered and contrast enhanced to accentuate surface detail, and geometrically transformed into a Lambert conformal projection.

The illuminated surface observed by Mariner 10 as it first approached Mercury is dominated by craters and basins. In marked contrast to this view, the surface photographed after the flyby exhibited features totally different, including large basins and extensive relatively smooth areas with few craters. The most striking feature in this region of the planet is a huge circular basin, 1300 kilometers in diameter, that was undoubtedly produced from a tremendous impact comparable to the event that formed the Imbrium basin on the Moon. This prominent Mercurian structure in the Shakespeare and Tolstoj quadrangles (lower left corner of this image), named Caloris Planitia, is filled with material forming a smooth surface or plain that appears similar in many respects to the lunar maria.

The above material was taken from the following publication... Davies, M. E., S. E. Dwornik, D. E. Gault, and R. G. Strom, Atlas of Mercury, NASA SP-423 (1978).

The Mariner 10 mission was managed by the Jet Propulsion Laboratory for NASA's Office of Space Science.

Density functional analysis of fluorite-structured (Ce, Zr)O 2/CeO 2 interfaces [Density functional analysis of fluorite-structured (Ce, Zr)O 2/CeO 2 interfaces: Implications for catalysis and energy applications

DOE PAGES

Weck, Philippe F.; Juan, Pierre -Alexandre; Dingreville, Remi; ...

2017-06-21

The structures and properties of Ce 1–xZr xO 2 (x = 0–1) solid solutions, selected Ce 1–xZr xO 2 surfaces, and Ce 1–xZr xO 2/CeO 2 interfaces were computed within the framework of density functional theory corrected for strong electron correlation (DFT+ U). The calculated Debye temperature increases steadily with Zr content in (Ce, Zr)O 2 phases, indicating a significant rise in microhardness from CeO 2 to ZrO 2, without appreciable loss in ductility as the interfacial stoichiometry changes. Surface energy calculations for the low-index CeO 2(111) and (110) surfaces show limited sensitivity to strong 4f-electron correlation. The fracture energymore » of Ce 1–xZr xO 2(111)/CeO 2(111) increases markedly with Zr content, with a significant decrease in energy for thicker Ce 1–xZr xO 2 films. These findings suggest the crucial role of Zr acting as a binder at the Ce 1–xZr xO 2/CeO 2 interfaces, due to the more covalent character of Zr–O bonds compared to Ce–O. Finally, the impact of surface relaxation upon interface cracking was assessed and found to reach a maximum for Ce 0.25Zr 0.75O 2/CeO 2 interfaces.« less

Geologic map of the Artemis Chasma quadrangle (V-48), Venus

USGS Publications Warehouse

Bannister, Roger A.; Hansen, Vicki L.

2010-01-01

Artemis, named for the Greek goddess of the hunt, represents an approximately 2,600 km diameter circular feature on Venus, and it may represent the largest circular structure in our solar system. Artemis, which lies between the rugged highlands of Aphrodite Terra to the north and relatively smooth lowlands to the south, includes an interior topographic high surrounded by the 2,100-km-diameter, 25- to 200-km-wide, 1- to 2-km-deep circular trough, called Artemis Chasma, and an outer rise that grades outward into the surrounding lowland. Although several other chasmata exist in the area and globally, other chasmata have generally linear trends that lack the distinctive circular pattern of Artemis Chasma. The enigmatic nature of Artemis has perplexed researchers since Artemis Chasma was first identified in Pioneer Venus data. Although Venus' surface abounds with circular to quasi-circular features at a variety of scales, including from smallest to largest diameter features: small shield edifices (>1 km), large volcanic edifices (100-1,000 km), impact craters (1-270 km), coronae (60-1,010 km), volcanic rises and crustal plateaus (~1,500-2,500 km), Artemis defies classification into any of these groups. Artemis dwarfs Venus' largest impact crater, Mead (~280 km diameter); Artemis also lacks the basin topography, multiple ring structures, and central peak expected for large impact basins. Topographically, Artemis resembles some Venusian coronae; however Artemis is an order of magnitude larger than the average corona (200 km) and about twice the size of Heng-O Corona (which is 1,010 km in diameter), the largest of Venusian coronae. In map view Artemis' size and shape resemble volcanic rises and crustal plateaus; however, both of these classes of features differ topographically from Artemis. Volcanic rises and crustal plateaus form broad domical regions, and steep-sided regions with flat tops, respectively; furthermore, neither rises nor plateaus include circular troughs. So although it seems clear what Artemis is not, there is little consensus about what Artemis is, much less how Artemis formed. Debate during the past decade has resulted in the proposal of at least four hypotheses for Artemis' formation. The first (herein referred to as H1) is that Artemis Chasma represents a zone of northwest-directed convergence and subduction. The second hypothesis (herein referred to as H2) is that Artemis consists of a composite structure with a part of its interior region marking the exposure of deformed ductile deep-crustal rocks analogous to a terrestrial metamorphic core complex. The third (herein referred to as H3) is that Artemis reflects the surface expression of an ancient (>3.5 Ga) huge bolide impact event on cold strong lithosphere. The fourth hypothesis (herein referred to as H4) is that Artemis marks the surface expression of a deep mantle plume. Each of these hypotheses holds different implications for Venus geodynamics and evolution processes, and for terrestrial planet processes in general. Viability of H1 would provide support that terrestrial-like plate-tectonic processes once occurred on Earth's sister planet. The feasibility of H2 would require high values of crustal extension and therefore imply that significant horizontal displacements occurred on Venus-displacement that may or may not be related to terrestrial-like plate-tectonic processes. The possibility of H3 would suggest that Venus' surface is extremely old, and that Venus has experienced very little dynamic activity for the last 3.5 billion years or more; this would further imply that Venus is essentially tectonically dead, and has been for most of its history. This view contrasts strongly with studies that highlight a rich history of Venus including activity at least as young as 750 million years ago, and quite likely up to the present. If H4 has credibility, then Artemis could provide clues to cooling mechanisms of Earth's sister planet. Each of these hypotheses

Influence of the axial rotation angle on tool mark striations.

PubMed

Garcia, Derrel Louis; Pieterman, René; Baiker, Martin

2017-10-01

A tool's axial rotation influences the geometric properties of a tool mark. The larger the axial rotation angle, the larger the compression of structural details like striations. This complicates comparing tool marks at different axial rotations. Using chisels, tool marks were made from 0° to 75° axial rotation and compared using an automated approach Baiker et al. [10]. In addition, a 3D topographic surface of a chisel was obtained to generate virtual tool marks and to test whether the axial rotation angle of a mark could be predicted. After examination of the tool mark and chisel data-sets it was observed that marks lose information with increasing rotation due to the change in relative distance between geometrical details on the tool and the disappearance of smaller details. The similarity and repeatability were high for comparisons between marks with no difference in axial rotation, but decreasing with increased rotation angle from 0° to 75°. With an increasing difference in the rotation angles, the tool marks had to be corrected to account for the different compression factors between them. For compression up to 7.5%, this was obtained automatically by the tool mark alignment method. For larger compression, manually re-sizing the marks to the uncompressed widths at 0° rotation before the alignment was found suitable for successfully comparing even large differences in axial rotation. The similarity and repeatability were decreasing however, with increasing degree of re-sizing. The quality was assessed by determining the similarity at different detail levels within a tool mark. With an axial rotation up to 75°, tool marks were found to reliably represent structural details down to 100μm. The similarity of structural details below 100μm was dependent on the angle, with the highest similarity at small rotation angles and the lowest similarity at large rotation angles. Filtering to remove the details below 100μm lead to consistently higher similarity between tool marks at all angles and allowed for a comparison of marks up to 75° axial rotation. Finally, generated virtual tool mark profiles with an axial rotation were compared to experimental tool marks. The similarity between virtual and experimental tool marks remained high up to 60° rotation after which it decreased due to the loss in quality in both marks. Predicting the rotation angle is possible under certain conditions up to 45° rotation with an accuracy of 2.667±0.577° rotation. Copyright © 2017 Elsevier B.V. All rights reserved.

Anaglyph, Yucatan Peninsula, Mexico

NASA Technical Reports Server (NTRS)

2003-01-01

This anaglyph (stereoscopic view) of Mexico's Yucatan Peninsula was generated entirely from Shuttle Radar Topography Mission (SRTM) data, and shows a subtle but distinctive indication of the Chicxulub impact crater. Most scientists now agree that this impact was the cause of the Cretatious-Tertiary extinction, the event 65 million years ago that marked the demise of the dinosaurs as well as the majority of life then on Earth. The crater's rim is marked by a shallow semicircular depression arcing about an offshore center point in the upper left of the picture. (The arcing depression is just above the blue line, when viewed with the naked eye.) This depression, or trough, only about 3 to 5 meters (10 - 15 feet) deep and about 5 kilometers (3 miles) wide, was likely caused by collapse of limestone caverns preferentially above the crater rim, resulting in an arcing chain of sinkholes. The limestone that covers most of the Yucatan Peninsula post-dates the impact crater. However, the crater pattern apparently controls the subsidence pattern just enough to show through.

This anaglyph was created by deriving a shaded relief image from the SRTM data, draping it back over the SRTM elevation model, and then generating two differing perspectives, one for each eye. Illumination is from the north (top). When viewed through special glasses, the anaglyph is a vertically exaggerated view of the Earth's surface in its full three dimensions. Anaglyph glasses cover the left eye with a red filter and cover the right eye with a blue filter. The total relief (range of elevations) across this entire image is less than 300 meters (1000 feet).

Elevation data used in this image were acquired by the Shuttle Radar Topography Mission (SRTM) aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C.

Size: 465 by 334 kilometers (288 by 207 miles) Location: 20 degrees North latitude, 89 degrees West longitude Orientation: North toward the top Image Data: Shaded SRTM elevation model Original Data Resolution: SRTM 1 arcsecond (about 30 meters or 98 feet) Date Acquired: February 2000

Rough SERS substrate based on gold coated porous silicon layer prepared on the silicon backside surface

NASA Astrophysics Data System (ADS)

Dridi, H.; Haji, L.; Moadhen, A.

2017-04-01

We report in this paper a novel method to elaborate rough Surface Enhanced Raman Scattering (SERS) substrate. A single layer of porous silicon was formed on the silicon backside surface. Morphological characteristics of the porous silicon layer before and after gold deposition were influenced by the rough character (gold size). The reflectance measurements showed a dependence of the gold nano-grains size on the surface nature, through the Localized Surface Plasmon (LSP) band properties. SERS signal of Rhodamine 6G used as a model analyte, adsorbed on the rough porous silicon layer revealed a marked enhancement of its vibrational modes intensities.

Surface modifications of the Sima de los Huesos fossil humans.

PubMed

Andrews, P; Fernandez Jalvo, Y

1997-01-01

The sample of fossil human bones from the Sima de los Huesos, Atapuerca, has been analysed to trace parts of its taphonomic history. The work reported here is restricted to analysis of the skeletal elements preserved and their surface modifications. Preliminary plans of specimen distribution published 6 years ago indicate that the skeletal elements are dispersed within the cave, but more recent data are not yet available. Most of the fossils are broken, with some breakage when the bone was fresh and some when already partly mineralized, both types showing some rounding. There are few longitudinal breaks on shafts of long bones and so very few bone splinters. All skeletal elements are preserved but in unequal proportions, with elements like femora, humeri and mandibles and teeth with greater structural density being best represented. There is no evidence of weathering or of human damage such as cut marks on any of the human assemblage, but trampling damage is present on most bones. Carnivore damage is also common, with some present on more than half the sample, but it is mostly superficial, either on the surfaces of shafts and articular ends or on the edges of spiral breaks. The sizes and distribution of the carnivore pits indicate extensive canid activity, and this is interpreted as scavenging of the bones in place in the cave. Indications of tooth marks from a larger carnivore indicate the activity possibly of a large felid: the marks are too large to be produced by small canids, with the larger marks concentrated on spiral breaks on the more robust bones, and there is no evidence of bone crushing and splintering in the manner of hyaenas. The nature of the SH human assemblage is also consistent with accumulation by humans, the evidence for this being the lack of other animals, especially the lack of herbivorous animals, associated with the humans, and the high number of individuals preserved.

Global impacts of conversions from natural to agricultural ecosystems on water resources: Quantity versus quality

NASA Astrophysics Data System (ADS)

Scanlon, Bridget R.; Jolly, Ian; Sophocleous, Marios; Zhang, Lu

2007-03-01

Past land use changes have greatly impacted global water resources, with often opposing effects on water quantity and quality. Increases in rain-fed cropland (460%) and pastureland (560%) during the past 300 years from forest and grasslands decreased evapotranspiration and increased recharge (two orders of magnitude) and streamflow (one order of magnitude). However, increased water quantity degraded water quality by mobilization of salts, salinization caused by shallow water tables, and fertilizer leaching into underlying aquifers that discharge to streams. Since the 1950s, irrigated agriculture has expanded globally by 174%, accounting for ˜90% of global freshwater consumption. Irrigation based on surface water reduced streamflow and raised water tables resulting in waterlogging in many areas (China, India, and United States). Marked increases in groundwater-fed irrigation in the last few decades in these areas has lowered water tables (≤1 m/yr) and reduced streamflow. Degradation of water quality in irrigated areas has resulted from processes similar to those in rain-fed agriculture: salt mobilization, salinization in waterlogged areas, and fertilizer leaching. Strategies for remediating water resource problems related to agriculture often have opposing effects on water quantity and quality. Long time lags (decades to centuries) between land use changes and system response (e.g., recharge, streamflow, and water quality), particularly in semiarid regions, mean that the full impact of land use changes has not been realized in many areas and remediation to reverse impacts will also take a long time. Future land use changes should consider potential impacts on water resources, particularly trade-offs between water, salt, and nutrient balances, to develop sustainable water resources to meet human and ecosystem needs.

The Argyre Region as a Prime Target for in situ Astrobiological Exploration of Mars.

PubMed

Fairén, Alberto G; Dohm, James M; Rodríguez, J Alexis P; Uceda, Esther R; Kargel, Jeffrey; Soare, Richard; Cleaves, H James; Oehler, Dorothy; Schulze-Makuch, Dirk; Essefi, Elhoucine; Banks, Maria E; Komatsu, Goro; Fink, Wolfgang; Robbins, Stuart; Yan, Jianguo; Miyamoto, Hideaki; Maruyama, Shigenori; Baker, Victor R

2016-02-01

At the time before ∼3.5 Ga that life originated and began to spread on Earth, Mars was a wetter and more geologically dynamic planet than it is today. The Argyre basin, in the southern cratered highlands of Mars, formed from a giant impact at ∼3.93 Ga, which generated an enormous basin approximately 1800 km in diameter. The early post-impact environment of the Argyre basin possibly contained many of the ingredients that are thought to be necessary for life: abundant and long-lived liquid water, biogenic elements, and energy sources, all of which would have supported a regional environment favorable for the origin and the persistence of life. We discuss the astrobiological significance of some landscape features and terrain types in the Argyre region that are promising and accessible sites for astrobiological exploration. These include (i) deposits related to the hydrothermal activity associated with the Argyre impact event, subsequent impacts, and those associated with the migration of heated water along Argyre-induced basement structures; (ii) constructs along the floor of the basin that could mark venting of volatiles, possibly related to the development of mud volcanoes; (iii) features interpreted as ice-cored mounds (open-system pingos), whose origin and development could be the result of deeply seated groundwater upwelling to the surface; (iv) sedimentary deposits related to the formation of glaciers along the basin's margins, such as evidenced by the ridges interpreted to be eskers on the basin floor; (v) sedimentary deposits related to the formation of lakes in both the primary Argyre basin and other smaller impact-derived basins along the margin, including those in the highly degraded rim materials; and (vi) crater-wall gullies, whose morphology points to a structural origin and discharge of (wet) flows.

Global impacts of conversions from natural to agricultural ecosystems on water resources: Quantity versus quality

USGS Publications Warehouse

Scanlon, Bridget R.; Jolly, Ian; Sophocleous, Marios; Zhang, Lu

2007-01-01

Past land use changes have greatly impacted global water resources, with often opposing effects on water quantity and quality. Increases in rain‐fed cropland (460%) and pastureland (560%) during the past 300 years from forest and grasslands decreased evapotranspiration and increased recharge (two orders of magnitude) and streamflow (one order of magnitude). However, increased water quantity degraded water quality by mobilization of salts, salinization caused by shallow water tables, and fertilizer leaching into underlying aquifers that discharge to streams. Since the 1950s, irrigated agriculture has expanded globally by 174%, accounting for ∼90% of global freshwater consumption. Irrigation based on surface water reduced streamflow and raised water tables resulting in waterlogging in many areas (China, India, and United States). Marked increases in groundwater‐fed irrigation in the last few decades in these areas has lowered water tables (≤1 m/yr) and reduced streamflow. Degradation of water quality in irrigated areas has resulted from processes similar to those in rain‐fed agriculture: salt mobilization, salinization in waterlogged areas, and fertilizer leaching. Strategies for remediating water resource problems related to agriculture often have opposing effects on water quantity and quality. Long time lags (decades to centuries) between land use changes and system response (e.g., recharge, streamflow, and water quality), particularly in semiarid regions, mean that the full impact of land use changes has not been realized in many areas and remediation to reverse impacts will also take a long time. Future land use changes should consider potential impacts on water resources, particularly trade‐offs between water, salt, and nutrient balances, to develop sustainable water resources to meet human and ecosystem needs.

Effect of Various Material Properties on the Adhesive Stage of Fretting

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1974-01-01

Various properties of metals and alloys were studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films were found to influence adhesion. High atomic density, low surface energy grain orientations exhibited lower adhesion than other orientations. Knowledge of interfacial surface binding energies assists in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents accomplishes both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

77 FR 58539 - Environmental Impacts Statements; Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-21

..., Fort Bend, Wharton, and Jackson Counties, TX, Comment Period Ends: 11/05/2012, Contact: Mark J..., Implementing Multiple Resource Management Activities, Black Hills National Forest, Custer, Fall River, Lawrence...

Test Track Facilities

DTIC Science & Technology

1979-12-01

the surface, together with the effect of flying flintstones results in severe wear to the tyres , brake pipes and all other fittings found underneath a...The building also contains the following test facilities. A 15 m square flat floor used for vehicle measurement accuracy checks, tyre deflections, and... tyres . The course is regularly maintained but dependant on weather, the surface condition may display marked differences. Alpine Course This is a

Infinite Coordination Polymer Nano- and Micro-Particles

DTIC Science & Technology

2015-06-12

Mirkin, Tobin J. Marks, Joseph T. Hupp. SiO2 Aerogel-templated, Porous TiO2 Photoanodes for Enhanced Performances in Dye-Sensitized Solar Cells ...nano-scale ICPs and their selective surface functionalization, we examined if indeed these ICP-DNA hybrid structures could enter cells and...surface functionalization. In particular, we aimed to utilize this fundamental understanding for the realization of nano-scale ICP-biomolecule hybrids

SUSTAINED HYPERLIPEMIA INDUCED IN RABBITS BY MEANS OF INTRAVENOUSLY INJECTED SURFACE-ACTIVE AGENTS

PubMed Central

Kellner, Aaron; Correll, James W.; Ladd, Anthony T.

1951-01-01

The intravenous injection of the surface-active agents Tween 80 and Triton A20 into rabbits fed a normal diet resulted in marked and sustained elevations of the cholesterol, phospholipid, and total lipid content of their blood. The increase in phospholipid in general paralleled that of the blood cholesterol. The implications of the findings are briefly discussed. PMID:14824409

Mass Wasting

NASA Image and Video Library

2011-12-06

Mass Wasting is the term given to the process of change on a surface due to gravity things moving downhill due to the force of gravity. Dark streaks mark the slopes of craters and hills in this region of Amazonis Planitia.

Projected Changes in Mean and Interannual Variability of Surface Water over Continental China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leng, Guoyong; Tang, Qiuhong; Huang, Maoyi

Five General Circulation Model (GCM) climate projections under the RCP8.5 emission scenario were used to drive the Variable Infiltration Capacity (VIC) hydrologic model to investigate the impacts of climate change on hydrologic cycle over continental China in the 21st century. The bias-corrected climatic variables were generated for the Fifth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC AR5) by the Inter-Sectoral Impact Model Intercomparison Project (ISI-MIP). Results showed much larger fractional changes of annual mean Evaportranspiration (ET) per unit warming than the corresponding fractional changes of Precipitation (P) per unit warming across the country especially for South China,more » which led to notable decrease of surface water variability (P-E). Specifically, negative trends for annual mean runoff up to -0.33%/decade and soil moisture trends varying between -0.02 to -0.13%/decade were found for most river basins across China. Coincidentally, interannual variability for both runoff and soil moisture exhibited significant positive trends for almost all river basins across China, implying an increase in extremes relative to the mean conditions. Noticeably, the largest positive trends for runoff variability and soil moisture variability, which were up to 38 0.41%/decade and 0.90%/decade, both occurred in Southwest China. In addition to the regional contrast, intra-seasonal variation was also large for the runoff mean and runoff variability changes, but small for the soil moisture mean and variability changes. Our results suggest that future climate change could further exacerbate existing water-related risks (e.g. floods and droughts) across China as indicated by the marked decrease of surface water amounts combined with steady increase of interannual variability throughout the 21st century. This study highlights the regional contrast and intra-seasonal variations for the projected hydrologic changes and could provide muti-scale guidance for assessing effective adaptation strategies for the country on a river basin, regional, or as whole.« less

Impact of nitrate-enhanced leachate recirculation on gaseous releases from a landfill bioreactor cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tallec, G.; Bureau, C.; Peu, P.

2009-07-15

This study evaluates the impact of nitrate injection on a full scale landfill bioreactor through the monitoring of gaseous releases and particularly N{sub 2}O emissions. During several weeks, we monitored gas concentrations in the landfill gas collection system as well as surface gas releases with a series of seven static chambers. These devices were directly connected to a gas chromatograph coupled to a flame ionisation detector and an electron capture detector (GC-FID/ECD) placed directly on the field. Measurements were performed before, during and after recirculation of raw leachate and nitrate-enhanced leachate. Raw leachate recirculation did not have a significant effectmore » on the biogas concentrations (CO{sub 2}, CH{sub 4} and N{sub 2}O) in the gas extraction network. However, nitrate-enhanced leachate recirculation induced a marked increase of the N{sub 2}O concentrations in the gas collected from the recirculation trench (100-fold increase from 0.2 ppm to 23 ppm). In the common gas collection system however, this N{sub 2}O increase was no more detectable because of dilution by gas coming from other cells or ambient air intrusion. Surface releases through the temporary cover were characterized by a large spatial and temporal variability. One automated chamber gave limited standard errors over each experimental period for N{sub 2}O releases: 8.1 {+-} 0.16 mg m{sup -2} d{sup -1} (n = 384), 4.2 {+-} 0.14 mg m{sup -2} d{sup -1} (n = 132) and 1.9 {+-} 0.10 mg m{sup -2} d{sup -1} (n = 49), during, after raw leachate and nitrate-enhanced leachate recirculation, respectively. No clear correlation between N{sub 2}O gaseous surface releases and recirculation events were evidenced. Estimated N{sub 2}O fluxes remained in the lower range of what is reported in the literature for landfill covers, even after nitrate injection.« less

Analytical methods for chemical and sensory characterization of scent-markings in large wild mammals: a review.

PubMed

Soso, Simone B; Koziel, Jacek A; Johnson, Anna; Lee, Young Jin; Fairbanks, W Sue

2014-03-05

In conjoining the disciplines of "ethology" and "chemistry" the field of "Ethochemistry" has been instituted. Ethochemistry is an effective tool in conservation efforts of endangered species and the understanding of behavioral patterns across all species. Chemical constituents of scent-markings have an important, yet poorly understood function in territoriality, reproduction, dominance, and impact on evolutionary biology, especially in large mammals. Particular attention has recently been focused on scent-marking analysis of great cats (Kalahari leopards (Panthera pardus), puma (Puma concolor) snow leopard (Panthera uncia), African lions (Panthera leo), cheetahs (Acinonyx jubatus), and tigers (Panthera tigris)) for the purpose of conservation. Sensory analyses of scent-markings could address knowledge gaps in ethochemistry. The objective of this review is to summarize the current state-of-the art of both the chemical and sensory analyses of scent-markings in wild mammals. Specific focus is placed on sampling and sample preparation, chemical analysis, sensory analysis, and simultaneous chemical and sensory analyses. Constituents of exocrine and endocrine secretions have been most commonly studied with chromatography-based analytical separations. Odor analysis of scent-markings provides an insight into the animal's sensory perception. A limited number of articles have been published in the area of sensory characterization of scent marks. Simultaneous chemical and sensory analyses with chromatography-olfactometry hyphenation could potentially aid conservation efforts by linking perceived odor, compounds responsible for odor, and resulting behavior.

Dissimilar Kinetic Behavior of Electrically Manipulated Single- and Double-Stranded DNA Tethered to a Gold Surface

PubMed Central

Rant, Ulrich; Arinaga, Kenji; Tornow, Marc; Kim, Yong Woon; Netz, Roland R.; Fujita, Shozo; Yokoyama, Naoki; Abstreiter, Gerhard

2006-01-01

We report on the electrical manipulation of single- and double-stranded oligodeoxynucleotides that are end tethered to gold surfaces in electrolyte solution. The response to alternating repulsive and attractive electric surface fields is studied by time-resolved fluorescence measurements, revealing markedly distinct dynamics for the flexible single-stranded and stiff double-stranded DNA, respectively. Hydrodynamic simulations rationalize this finding and disclose two different kinetic mechanisms: stiff polymers undergo rotation around the anchoring pivot point; flexible polymers, on the other hand, are pulled onto the attracting surface segment by segment. PMID:16473909

Dissimilar kinetic behavior of electrically manipulated single- and double-stranded DNA tethered to a gold surface.

PubMed

Rant, Ulrich; Arinaga, Kenji; Tornow, Marc; Kim, Yong Woon; Netz, Roland R; Fujita, Shozo; Yokoyama, Naoki; Abstreiter, Gerhard

2006-05-15

We report on the electrical manipulation of single- and double-stranded oligodeoxynucleotides that are end tethered to gold surfaces in electrolyte solution. The response to alternating repulsive and attractive electric surface fields is studied by time-resolved fluorescence measurements, revealing markedly distinct dynamics for the flexible single-stranded and stiff double-stranded DNA, respectively. Hydrodynamic simulations rationalize this finding and disclose two different kinetic mechanisms: stiff polymers undergo rotation around the anchoring pivot point; flexible polymers, on the other hand, are pulled onto the attracting surface segment by segment.

Unraveling the Nature of Active Sites in Ethanol Electro-oxidation by Site-Specific Marking of a Pt Catalyst with Isotope-Labeled 13CO.

PubMed

Farias, Manuel J S; Cheuquepán, William; Tanaka, Auro A; Feliu, Juan M

2018-03-15

This works deals with the identification of preferential site-specific activation at a model Pt surface during a multiproduct reaction. The (110)-type steps of a Pt(332) surface were selectively marked by attaching isotope-labeled 13 CO molecules to them, and ethanol oxidation was probed by in situ Foureir transfrom infrared spectroscopy in order to precisely determine the specific sites at which CO 2 , acetic acid, and acetaldehyde were preferentially formed. The (110) steps were active for splitting the C-C bond, but unexpectedly, we provide evidence that the pathway of CO 2 formation was preferentially activated at (111) terraces, rather than at (110) steps. Acetaldehyde was formed at (111) terraces at potentials comparable to those for CO 2 formation also at (111) terraces, while the acetic acid formation pathway became active only when the (110) steps were released by the oxidation of adsorbed 13 CO, at potentials higher than for the formation of CO 2 at (111) terraces of the stepped surface.

Thermomechanical modeling of the Colorado Plateau-Basin and range transition zone

NASA Technical Reports Server (NTRS)

Londe, M. D.

1985-01-01

The Colorado Plateau (CP) basin and range (B & R) boundary is marked by a transition zone on the order of 75 to 150 km in width. As one moves westward across this transition from the CP interior to the B & R there is a variation in the surface topography, surface heat flow, Bouguer gravity, seismicity, and crustal structure. This transition extends eastward into the western CP from the Wastach-Hurricane fault line and is largely coincident with the high plateaus of Utah and the Wasatch Mountains. It has been suggested that this transition zone marks a thermal and tectonic encroachment of the CP by the B & R. A simple two dimensional numerical model of the thermal regime for the transition zone was constructed to test the hypothesis that the observed geophysical signatures across the transition are due to lateral heat conduction from steady state uniform extension within the B & R lithosphere. Surface heat flow, uplift due to flexure from thermal buoyant loading, and regional Bouguer gravity are computed for various extension rates, crustal structures, and compensation depths.

Copper vapour laser ID labelling on metal dentures and restorations.

PubMed

Ling, B C; Nambiar, P; Low, K S; Lee, C K

2003-06-01

Denture marking is accepted as a means of identifying dentures and persons in geriatric institutions, or post-mortem during war, crimes, civil unrest, natural and mass disasters. Labelling on the acrylic resin component of the denture can easily be damaged or destroyed by fire but on cobalt-chromium components it would be more resistant. A copper vapour laser (CVL) can be used to label the cobalt-chromium components of dentures and metal restorations easily, and legibly, and miniaturised for the incorporation of more personal particulars necessary for the identification of the deceased person. The CVL beam is focussed by its optics and delivered to the material surface by the two-axis scanner mounted with mirrors. A personal computer controls the movement of the scanner and the firing of the CVL. The high peak power of the pulsed CVL is focussed to very high energy density producing plasma ablation of the alloy surface. Very fine markings of a few microns width can be produced enabling the storage of detailed information of the deceased person on a metal surface for the purpose of rapid identification.

Fractography of poly(methyl methacrylates).

PubMed

Kusy, R P; Turner, D T

1975-07-01

For convenience in clinical manipulation, it is the practice to fabricate PMMA protheses from mixtures of powder and monomer. When the monomer is subsequently polymerized an unusual 2-phase polymeric material results in which grains of PMMA are dispersed in a matrix of the same polymer. The mechanical properties of the 2-phase materials are inferior in certain respects relative to 1-phase polymers. The purpose of the present work is to evaluate the failure of 2-phase materials by microscopical examination of their fracture surfaces. A granular microstructure was clearly distinguishable and a distinction made between materials which fail exclusively by transgranular fracture and others which additionally exhibit intergranular fracture. In order to interpret markings observed on the fracture surfaces of the complex 2-phase systems a study was made of the influence of molecular weight on the fractography of 1-phase PMMA. Molecular weight was reduced by degradation of samples by exposure to gamma-rays. The spacing of periodic rib markings on fracture surfaces was found to decrease with molecular weight and this relationship used to provide an estimate of the molecular weight of polymer in the matrix of 2-phase materials.

Evaluation of enamel by scanning electron microscopy green LED associated to hydrogen peroxide 35% for dental bleaching

NASA Astrophysics Data System (ADS)

Monteiro, Juliana S. C.; de Oliveira, Susana C. P. S.; Zanin, Fátima A. A.; Santos, Gustavo M. P.; Sampaio, Fernando J. P.; Gomes Júnior, Rafael Araújo; Gesteira, Maria F. M.; Vannier-Santos, Marcos A.; Pinheiro, Antônio Luiz B.

2014-02-01

Dental bleaching is a frequently requested procedure in clinical dental practice. The literature is contradictory regarding the effects of bleaching agents on both morphology and demineralization of enamel after bleaching. The aim of this study was to analyze by SEM the effect of 35% neutral hydrogen peroxide cured by green LED. Buccal surfaces of 15 pre-molars were sectioned and marked with a central groove to allow experimental and control groups on the same specimen. For SEM, 75 electron micrographs were evaluated by tree observers at 43X, 220X and 1000X. Quantitative analysis for the determination of the surface elemental composition of the samples through X-ray microanalysis by SEM was also performed. The protocol tested neither showed significant changes in mineral composition of the samples nor to dental enamel structure when compared to controls. SEM analysis allowed inferring that there were marked morphological differences between the enamel samples highlighting the need for the use of the same tooth in comparative morphological studies. The tested protocol did not cause morphological damage the enamel surface when compared to their respective controls.

The Role of Disturbance in Arctic Ecosystem Response to a Changing Climate

NASA Astrophysics Data System (ADS)

Hinzman, L. D.

2014-12-01

Wildfires in the tundra regions and the boreal forest project an immediate effect upon the surface energy and water budget by drastically altering the surface albedo, roughness, infiltration rates, and moisture absorption capacity in organic soils. Although fires create a sudden and drastic change to the landcover, it is only the beginning of a long process of recovery and perhaps a shift to a different successional pathway. In permafrost regions, these effects become part of a process of long-term (20-50 years) cumulative impacts. Burn severity may largely determine immediate impacts and long-term disturbance trajectories. As transpiration decreases or ceases, soil moisture increases markedly, remaining quite wet throughout the year. Because the insulating quality of the organic layer is removed during fires, permafrost begins to thaw near the surface and warm to greater depths. Within a few years, it may thaw to the point where it can no longer completely refreeze every winter, creating a permanently thawed layer in the soil called a talik. After formation of a talik, soils can drain internally throughout the year. At this point, soils may become quite dry, as the total precipitation received annually in the Arctic is quite low. The local ecological community must continuously adapt to the changing soil thermal and moisture regimes. The wet soils found over shallow permafrost favor black spruce forests. After a fire creates a deeper permafrost table (thicker active layer) the invading tree species tend to be birch or alder. The hydrologic and thermal regime of the soil is the primary factor controlling these vegetation trajectories and the subsequent changes in surface mass and energy fluxes. The complexities of a changing climate accentuate these processes of change and complicate predictions of the resulting vegetation trajectories. Understanding these shifts in vegetative communities and quantifying the consequences of thawing permafrost can only be accomplished through complementary analyses of field research data and numerical simulations. The permafrost dramatically controls other landscape features and its dynamic response to thermal influences yield consequent effects on the surficial ecology, water and energy balances and regional climate.

Impacts of road construction and removal on the hydrologic and geochemical function of a fen peatland

NASA Astrophysics Data System (ADS)

Wells, C. M.; Petrone, R. M.; Sutherland, G.; Price, J. S.

2015-12-01

Linear disturbances such as roads cover vast swaths of northeastern Alberta, the majority of which are wetlands with shallow and local hydrologic connections. Thus, the effects of road construction on wetland hydrological pathways can have significant implications on water movement within the region, and by extension the productivity of vegetation communities and carbon sequestration. However, little is known about the effect that roads have on wetland hydrology. In 2013, a gravel road built within a fen peatland was reclaimed to evaluate hydrologic impacts post removal. Prior to removal, ground and surface water flow was obstructed leading to surface ponding, and vegetation mortality was observed on the up-gradient (wet) side of the road. Rebounding of the peat column was observed throughout the fen immediately following road removal in 2013 (maximum of 12 cm, mean of 2 cm), with modest but slightly smaller expansion in 2014. For both years, peat rebound was greatest in areas where the road was removed. Peat physical properties contrasted sharply between the reclaimed road (RR) peat and the adjacent, unimpacted peatland (UP). Surface bulk densities (pb, 0-10 cm) ranged from 0.1-0.25 g cm-3 along the RR compared to 0.02-0.07 g cm-3 for the UP and on average, pb for all depths were lower at the RR compared to the UP. Similar spatial patterns were observed for peat porosity. Correspondingly low horizontal saturated hydraulic conductivities (Kh) were observed along the RR compared to the UP, averaging 5.7x10-4 m s-1 and 1.7x10-3 m s-1, respectively. The local flow system across the RR and thus subsurface flow was impeded by almost half (0.4 m d-1) compared to flow observed within the UP (0.8 m d-1), leading to ponding on the upgradient side. A marked change in hydrophysical properties and ground and surface water flow patterns post road removal has implications for plant reestablishment and restoration and will form the basis of further study.

Impact of agricultural management on pluvial flash floods - Case study of an extreme event observed in Austria in 2016

NASA Astrophysics Data System (ADS)

Lumassegger, Simon; Achleitner, Stefan; Kohl, Bernhard

2017-04-01

Central Europe was affected by extreme flash floods in summer 2016 triggered by short, high-intensity storm cells. Besides fluvial runoff, local pluvial floods appear to increase recently. In frame of the research project SAFFER-CC (sensitivity assessment of critical condition for local flash floods - evaluating the recurrence under climate change) surface runoff and pluvial flooding is assessed using a coupled hydrological/2D hydrodynamic model for the severely affected municipality of Schwertberg, Upper Austria. In this small catchment several flooding events occurred in the last years, where the most severe event occurred during summer 2016. Several areas could only be reached after the flood wave subsided with observed flood marks up to one meter. The modeled catchment is intensively cultivated with maize, sugar beets, winter wheat and soy on the hillside and hence highly vulnerable to water erosion. The average inclination is relatively steep with 15 % leading to high flow velocities of surface runoff associated with large amounts of transported sediments. To assess the influence of land use and soil conservation on flash floods, field experiments with a portable irrigation spray installation were carried out at different locations. The test plots were subjected to rainfall with constant intensity of 100 mm/h for one hour. Consecutively a super intense, one hour lasting, rainfall hydrograph was applied after 30 minutes at the same plots, ranging from 50 mm/h to 200 mm/h. Surface runoff was collected and measured in a tank and water samples were taken to determine the suspended material load. Large differences of runoff coefficients were determined depending on the agricultural management. The largest discharge was measured in a maize field, where surface runoff occurred immediately after start of irrigation. The determined runoff coefficients ranged from 0.22 for soy up to 0.65 for maize for the same soil type and inclination. The conclusion that runoff is heavily influenced by land use matches well with the observed flow patterns during the storm event in summer 2016. The results clearly indicate the ability to reduce pluvial flash flood impacts by changing agricultural management practices.

The examination and identification of bite marks in foods using 3D scanning and 3D comparison methods.

PubMed

Naether, Silvio; Buck, Ursula; Campana, Lorenzo; Breitbeck, Robert; Thali, Michael

2012-01-01

Bite mark analysis offers the opportunity to identify the biter based on the individual characteristics of the dentitions. Normally, the main focus is on analysing bite mark injuries on human bodies, but also, bite marks in food may play an important role in the forensic investigation of a crime. This study presents a comparison of simulated bite marks in different kinds of food with the dentitions of the presumed biter. Bite marks were produced by six adults in slices of buttered bread, apples, different kinds of Swiss chocolate and Swiss cheese. The time-lapse influence of the bite mark in food, under room temperature conditions, was also examined. For the documentation of the bite marks and the dentitions of the biters, 3D optical surface scanning technology was used. The comparison was performed using two different software packages: the ATOS modelling and analysing software and the 3D studio max animation software. The ATOS software enables an automatic computation of the deviation between the two meshes. In the present study, the bite marks and the dentitions were compared, as well as the meshes of each bite mark which were recorded in the different stages of time lapse. In the 3D studio max software, the act of biting was animated to compare the dentitions with the bite mark. The examined food recorded the individual characteristics of the dentitions very well. In all cases, the biter could be identified, and the dentitions of the other presumed biters could be excluded. The influence of the time lapse on the food depends on the kind of food and is shown on the diagrams. However, the identification of the biter could still be performed after a period of time, based on the recorded individual characteristics of the dentitions.

Medical Entomology Studies - XII. A Revision of the Aedes Scutellaris Group of Tonga (Diptera: Culicidae) (Contributions of the American Entomological Institute. Volume 17, Number 3, 1980)

DTIC Science & Technology

1980-01-01

Aedes Meigen serve as the primary vectors of subperiodic Wuchereria bancrofti ( Cobbold ) on many islands of the South Pacific. A thorough study to...hindfemur with basal 0.12 or less white (Fig. 16). upolensis Marks Lateral prescutal white line present, or at least with some narrow white scales on...or at most 0.07 white (Fig. 16). , . . . . . . . . . . . . . . polynesiensis Marks Dorsal surface of hindfemur with basal area 0.10 or more white

Lily Pad Spectra

NASA Technical Reports Server (NTRS)

2004-01-01

The color image on the lower left from the panoramic camera on the Mars Exploration Rover Opportunity shows the 'Lily Pad' bounce-mark area at Meridiani Planum, Mars. This image was acquired on the 3rd sol, or martian day, of Opportunity's mission (Jan.26, 2004). The upper left image is a monochrome (single filter) image from the rover's panoramic camera, showing regions from which spectra were extracted from the 'Lily Pad' area. As noted by the line graph on the right, the green spectra is from the undisturbed surface and the red spectra is from the airbag bounce mark.

Method and Apparatus for Reading Two Dimensional Identification Symbols Using Radar Techniques

NASA Technical Reports Server (NTRS)

Schramm, Harry F., Jr. (Inventor); Roxby, Donald L. (Inventor)

2003-01-01

A method and apparatus are provided for sensing two-dimensional identification marks provided on a substrate or embedded within a substrate below a surface of the substrate. Micropower impulse radar is used to transmit a high risetime, short duration pulse to a focussed radar target area of the substrate having the two dimensional identification marks. The method further includes the steps of listening for radar echoes returned from the identification marks during a short listening period window occurring a predetermined time after transmission of the radar pulse. If radar echoes are detected, an image processing step is carried out. If no radar echoes are detected, the method further includes sequentially transmitting further high risetime, short duration pulses, and listening for radar echoes from each of said further pulses after different elapsed times for each of the further pulses until radar echoes are detected. When radar echoes are detected, data based on the detected echoes is processed to produce an image of the identification marks.

Recognition of foreign oviposition-marking pheromone in a multi-trophic context

NASA Astrophysics Data System (ADS)

Stelinski, L. L.; Rodriguez-Saona, C.; Meyer, W. L.

2009-05-01

Both phytophagous and parasitic insects deposit oviposition-marking pheromones (OMPs) following oviposition that function to inform conspecifics of a previously utilized host of reduced suitability. The blueberry maggot fly, Rhagoletis mendax Curran (Diptera: Tephritidae), deposits eggs individually into blueberries and then marks the fruit surface with an OMP which reduces acceptance of fruit for oviposition by conspecifics. Diachasma alloeum (Muesebeck) (Hymenoptera: Braconidae) is a parasitic wasp attacking larval R. mendax which also deposits an OMP, signaling conspecifics of a wasp-occupied host. Behavioral studies were conducted testing the hypothesis that the OMP of the parasitic wasp modifies the oviposition behavior of its host fly. In this study, we show that the OMP of D. alloeum is recognized by R. mendax, and female flies will reject wasp-marked fruit for oviposition. Thus, we present a rare demonstration of pheromonal recognition between animals occupying different taxonomic orders and trophic levels. This chemical eavesdropping may enhance the ability of the fly to avoid fruit unsuitable for larval development.

Quantification of microscopic surface features of single point diamond turned optics with subsequent chemical polishing

NASA Astrophysics Data System (ADS)

Cardenas, Nelson; Kyrish, Matthew; Taylor, Daniel; Fraelich, Margaret; Lechuga, Oscar; Claytor, Richard; Claytor, Nelson

2015-03-01

Electro-Chemical Polishing is routinely used in the anodizing industry to achieve specular surface finishes of various metals products prior to anodizing. Electro-Chemical polishing functions by leveling the microscopic peaks and valleys of the substrate, thereby increasing specularity and reducing light scattering. The rate of attack is dependent of the physical characteristics (height, depth, and width) of the microscopic structures that constitute the surface finish. To prepare the sample, mechanical polishing such as buffing or grinding is typically required before etching. This type of mechanical polishing produces random microscopic structures at varying depths and widths, thus the electropolishing parameters are determined in an ad hoc basis. Alternatively, single point diamond turning offers excellent repeatability and highly specific control of substrate polishing parameters. While polishing, the diamond tool leaves behind an associated tool mark, which is related to the diamond tool geometry and machining parameters. Machine parameters such as tool cutting depth, speed and step over can be changed in situ, thus providing control of the spatial frequency of the microscopic structures characteristic of the surface topography of the substrate. By combining single point diamond turning with subsequent electro-chemical etching, ultra smooth polishing of both rotationally symmetric and free form mirrors and molds is possible. Additionally, machining parameters can be set to optimize post polishing for increased surface quality and reduced processing times. In this work, we present a study of substrate surface finish based on diamond turning tool mark spatial frequency with subsequent electro-chemical polishing.

Rotary Valve FY 2016 Highlights

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitsos, P.

The fiscal year started with the Rotary Valve (RV) being reassembled after having crashed in June of 2015. The crash occurred when the RV inner surface contacted the housing. The cause of the crash was never confirmed. No particles were found in the 2.5 thousandths of an inch gap and the filters the helium gas passed through were all clean. There were marks on the bearings that looked like electrostatic discharge as shown below in Figure 1. These marks hadn’t been seen before and there were similar discharge marks on some of the ball bearings. Examples of this were foundmore » in a literature search of bearing failures. This leads to a possible cause due to this arcing affecting the rotational accuracy of the bearings driving the RV into the housing.« less

Trends in Parent- and Teacher-Rated Emotional, Conduct and ADHD Problems and Their Impact in Prepubertal Children in Great Britain: 1999-2008

ERIC Educational Resources Information Center

Sellers, Ruth; Maughan, Barbara; Pickles, Andrew; Thapar, Anita; Collishaw, Stephan

2015-01-01

Background: Evidence from Western countries indicates marked increases in diagnosis and treatment of childhood psychiatric disorders in recent years. These could reflect changes in prevalence of mental health problems, changes in their impact or increased clinical recognition and help-seeking. Epidemiological cross-cohort comparisons are required…

Asking New Questions and Seeking New Answers: The Reality of Aphasia Practice in South Africa

ERIC Educational Resources Information Center

Penn, Claire

2014-01-01

Emerging policy in South Africa has had a marked impact on delivery of service by speech-language pathologists, particularly in the field of aphasia. This article describes major policy influences in the areas of language use, health, education, disability, and the elderly, which have had an impact on service delivery. Aphasia assessment and…

Assessing socioeconomic impacts of climate change on U.S. forests, wood-product markets, and forest recreation

Treesearch

Lloyd C. Irland; Darius Adams; Ralph Alig; Carter J. Betz; Chi-Chung Chen; Mark Hutchins; Bruce A. McCarl; Ken Skog; Brent L. Sohngen

2001-01-01

In this paper we discuss the problems of projecting social and economic changes affecting forests and review recent efforts to assess the wood-market impacts of possible climate changes. To illustrate the range of conditions encountered in projecting socioeconomic change linked to forests, we consider two markedly different uses: forest products markets and forest...

AlGaN/GaN heterostructures with an AlGaN layer grown directly on reactive-ion-etched GaN showing a high electron mobility (>1300 cm2 V-1 s-1)

NASA Astrophysics Data System (ADS)

Yamamoto, Akio; Makino, Shinya; Kanatani, Keito; Kuzuhara, Masaaki

2018-04-01

In this study, the metal-organic-vapor-phase-epitaxial growth behavior and electrical properties of AlGaN/GaN structures prepared by the growth of an AlGaN layer on a reactive-ion-etched (RIE) GaN surface without regrown GaN layers were investigated. The annealing of RIE-GaN surfaces in NH3 + H2 atmosphere, employed immediately before AlGaN growth, was a key process in obtaining a clean GaN surface for AlGaN growth, that is, in obtaining an electron mobility as high as 1350 cm2 V-1 s-1 in a fabricated AlGaN/RIE-GaN structure. High-electron-mobility transistors (HEMTs) were successfully fabricated with AlGaN/RIE-GaN wafers. With decreasing density of dotlike defects observed on the surfaces of AlGaN/RIE-GaN wafers, both two-dimensional electron gas properties of AlGaN/RIE-GaN structures and DC characteristics of HEMTs were markedly improved. Since dotlike defect density was markedly dependent on RIE lot, rather than on growth lot, surface contaminations of GaN during RIE were believed to be responsible for the formation of dotlike defects and, therefore, for the inferior electrical properties.

Hierarchy of sedimentary discontinuity surfaces and condensed beds from the middle Paleozoic of eastern North America: Implications for cratonic sequence stratigraphy

USGS Publications Warehouse

McLaughlin, P.I.; Brett, Carlton E.; Wilson, M.A.

2008-01-01

Sedimentological analyses of middle Paleozoic epeiric sea successions in North America suggest a hierarchy of discontinuity surfaces and condensed beds of increasing complexity. Simple firmgrounds and hardgrounds, which are comparatively ephemeral features, form the base of the hierarchy. Composite hardgrounds, reworked concretions, authigenic mineral crusts and monomictic intraformational conglomerates indicate more complex histories. Polymictic intraformational conglomerates, ironstones and phosphorites form the most complex discontinuity surfaces and condensed beds. Complexity of discontinuities is closely linked to depositional environments duration of sediment starvation and degree of reworking which in turn show a relationship to stratigraphic cyclicity. A model of cratonic sequence stratigraphy is generated by combining data on the complexity and lateral distribution of discontinuities in the context of facies successions. Lowstand, early transgressive and late transgressive systems tracts are representative of sea-level rise. Early and late transgressive systems tracts are separated by the maximum starvation surface (typically a polymictic intraformational conglomerate or condensed phosphorite), deposited during the peak rate of sea-level rise. Conversely the maximum flooding surface, representing the highest stand of sea level, is marked by little to no break in sedimentation. The highstand and falling stage systems tracts are deposited during relative sea-level fall. They are separated by the forced-regression surface, a thin discontinuity surface or condensed bed developed during the most rapid rate of sea-level fall. The lowest stand of sea level is marked by the sequence boundary. In subaerially exposed areas it is occasionally modified as a rockground or composite hardground.

Design Review Improvement Recommendations

DTIC Science & Technology

2015-06-18

Anne Ramsey, Harris Corporation Ronald H. Mandel, Lockheed Martin Mark King, Micropac Industries Melanie Berg, NASA Cindy Kohlmiller, Northrop...Donna Potter , SSL ii Executive Summary The aerospace industry continues to experience design escapes that significantly impact program

Data shopping in an open marketplace: Introducing the Ontogrator web application for marking up data using ontologies and browsing using facets.

PubMed

Morrison, Norman; Hancock, David; Hirschman, Lynette; Dawyndt, Peter; Verslyppe, Bert; Kyrpides, Nikos; Kottmann, Renzo; Yilmaz, Pelin; Glöckner, Frank Oliver; Grethe, Jeff; Booth, Tim; Sterk, Peter; Nenadic, Goran; Field, Dawn

2011-04-29

In the future, we hope to see an open and thriving data market in which users can find and select data from a wide range of data providers. In such an open access market, data are products that must be packaged accordingly. Increasingly, eCommerce sellers present heterogeneous product lines to buyers using faceted browsing. Using this approach we have developed the Ontogrator platform, which allows for rapid retrieval of data in a way that would be familiar to any online shopper. Using Knowledge Organization Systems (KOS), especially ontologies, Ontogrator uses text mining to mark up data and faceted browsing to help users navigate, query and retrieve data. Ontogrator offers the potential to impact scientific research in two major ways: 1) by significantly improving the retrieval of relevant information; and 2) by significantly reducing the time required to compose standard database queries and assemble information for further research. Here we present a pilot implementation developed in collaboration with the Genomic Standards Consortium (GSC) that includes content from the StrainInfo, GOLD, CAMERA, Silva and Pubmed databases. This implementation demonstrates the power of ontogration and highlights that the usefulness of this approach is fully dependent on both the quality of data and the KOS (ontologies) used. Ideally, the use and further expansion of this collaborative system will help to surface issues associated with the underlying quality of annotation and could lead to a systematic means for accessing integrated data resources.

Data shopping in an open marketplace: Introducing the Ontogrator web application for marking up data using ontologies and browsing using facets

PubMed Central

Morrison, Norman; Hancock, David; Hirschman, Lynette; Dawyndt, Peter; Verslyppe, Bert; Kyrpides, Nikos; Kottmann, Renzo; Yilmaz, Pelin; Glöckner, Frank Oliver; Grethe, Jeff; Booth, Tim; Sterk, Peter; Nenadic, Goran; Field, Dawn

2011-01-01

In the future, we hope to see an open and thriving data market in which users can find and select data from a wide range of data providers. In such an open access market, data are products that must be packaged accordingly. Increasingly, eCommerce sellers present heterogeneous product lines to buyers using faceted browsing. Using this approach we have developed the Ontogrator platform, which allows for rapid retrieval of data in a way that would be familiar to any online shopper. Using Knowledge Organization Systems (KOS), especially ontologies, Ontogrator uses text mining to mark up data and faceted browsing to help users navigate, query and retrieve data. Ontogrator offers the potential to impact scientific research in two major ways: 1) by significantly improving the retrieval of relevant information; and 2) by significantly reducing the time required to compose standard database queries and assemble information for further research. Here we present a pilot implementation developed in collaboration with the Genomic Standards Consortium (GSC) that includes content from the StrainInfo, GOLD, CAMERA, Silva and Pubmed databases. This implementation demonstrates the power of ontogration and highlights that the usefulness of this approach is fully dependent on both the quality of data and the KOS (ontologies) used. Ideally, the use and further expansion of this collaborative system will help to surface issues associated with the underlying quality of annotation and could lead to a systematic means for accessing integrated data resources. PMID:21677865

Experimental use of temporary traffic delineators : final report.

DOT National Transportation Integrated Search

1988-12-01

During construction, there is a safety need to provide highly visible channelizing delineation for temporary protection and direction of traffic. "Super Duck" Surface Mounted Delineator (SDR-328, Rounded) by Carsonite is marked to meet the safety nee...

A Descriptive Study Assessing Quality of Life for Adults With a Permanent Ostomy and the Influence of Preoperative Stoma Site Marking.

PubMed

Maydick, Diane

2016-05-01

Diseases or anomalies of the genitourinary or gastrointestinal tract often require removal of organs and creation of an artificial opening (stoma) to allow for elimination of urine or stool. Preoperative stoma site marking can affect quality of life (QoL). A descriptive study was conducted to assess the relationship between QoL and preoperative stoma site marking in adults with a permanent ostomy. Using convenience sampling methods, 230 eligible participants attending a United Ostomy Association of America conference were invited to complete a survey of demographics regarding age, gender, time since surgeries, and ostomy type and the City of Hope National Medical Center Quality of Life Ostomy Questionnaire. The latter contains 2 sections of 30 and 43 items each that address life impact and quality of life, respectively. The researcher explained the study and provided a study packet to volunteers who were interested in participating. Volunteers were to complete the surveys over a 4-day period while at the conference; the investigator collected all study materials. Inclusion criteria stipulated study participants must be English writing/reading persons at least 18 years of age with a colostomy, ileostomy, or urostomy. All descriptive statistics (means, standard deviation, frequency, and percents) used to describe demographic and surgical history and quantitative data (logistic regression, cross-tabulation, Pearson product moment correlations, and analysis of covariance) used to determine relationships among factors were entered and analyzed using a computer software program. Of the 140 participants who met inclusion criteria and provided data, the majority (85, 60.7%) had their stoma site marked by a wound, ostomy, continence (WOC) nurse. WOC nurse marking was more likely in recent years, and WOC nurse marking was 1.03 times more likely for each year since stoma surgery (M = 13.44, SD = 13.48). Mean QoL was 7.56 (SD = 1.59, range 3.84-10.00) and was positively correlated with age (r [137] = 0.27, P = 0.001), years since first surgery (r (138) = 0.25, P = 0.003), and years since most recent surgery (r [137] =0.28, P = 0.001). The total number of surgeries was unrelated to QoL. More than 75% of the participants received preoperative marking, with a significant difference in QoL for persons marked by a surgeon (M = 7.71, SE = 0.16) or a WOC nurse (M = 8.82, SE = 0.37) versus another professional (M = 4.83, SE = 1.05) (F [3.118] = 3.44, P = 0.19). The increasing prevalence of preoperative stoma site marking by a WOC nurse over time serves as a benchmark for this centerpiece of WOC nursing practice. The findings confirm the need for stoma site marking and validate the impact of stoma site marking by the WOC nurse.

Active control of residual tool marks for freeform optics functionalization by novel biaxial servo assisted fly cutting.

PubMed

Zhu, Zhiwei; To, Suet; Zhang, Shaojian

2015-09-01

The inherent residual tool marks (RTM) with particular patterns highly affect optical functions of the generated freeform optics in fast tool servo or slow tool servo (FTS/STS) diamond turning. In the present study, a novel biaxial servo assisted fly cutting (BSFC) method is developed for flexible control of the RTM to be a functional micro/nanotexture in freeform optics generation, which is generally hard to achieve in FTS/STS diamond turning. In the BSFC system, biaxial servo motions along the z-axis and side-feeding directions are mainly adopted for primary surface generation and RTM control, respectively. Active control of the RTM from the two aspects, namely, undesired effect elimination or effective functionalization, are experimentally demonstrated by fabricating a typical F-theta freeform surface with scattering homogenization and two functional microstructures with imposition of secondary phase gratings integrating both reflective and diffractive functions.

Thermoplastic microchannel fabrication using carbon dioxide laser ablation.

PubMed

Wang, Shau-Chun; Lee, Chia-Yu; Chen, Hsiao-Ping

2006-04-14

We report the procedures of machining microchannels on Vivak co-polyester thermoplastic substrates using a simple industrial CO(2) laser marker. To avoid overheating the substrates, we develop low-power marking techniques in nearly anaerobic environment. These procedures are able to machine microchannels at various aspect ratios. Either straight or serpent channel can be easily marked. Like the wire-embossed channel walls, the ablated channel surfaces become charged after alkaline hydrolysis treatment. Stable electroosmotic flow in the charged conduit is observed to be of the same order of magnitude as that in fused silica capillary. Typical dynamic coating protocols to alter the conduit surface properties are transferable to the ablated channels. The effects of buffer acidity on electroosmotic mobility in both bare and coated channels are similar to those in fused silica capillaries. Using video microscopy we also demonstrate that this device is useful in distinguishing the electrophoretic mobility of bare and latex particles from that of functionalized ones.

Visual detection of gas shows from coal core and cuttings using liquid leak detector

USGS Publications Warehouse

Barker, C.E.

2006-01-01

Portions of core or cutting samples that have active gas shows can be identified by applying a liquid leak detector to the core surface. Although these gas shows can be caused by manmade changes to the coals' internal structure and surface of the core during the coring process, in many cases, the marked gas shows overlie changes in maceral composition, subtle fractures or coal, coal structure and so forth that seemingly are places where natural primary permeability is higher and gas shows would be favored. Given the limited time available for core description before a core is closed in a canister, using the liquid leak detector method to mark gas shows enhances core description by providing a photographic record of places of apparently increased gas flow likely related to enhanced coal permeability that cannot be easily detected otherwise.

Detail view of the vertical stabilizer of the Orbiter Discovery ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of the vertical stabilizer of the Orbiter Discovery looking at the two-piece rudder which is used to control the yaw position of orbiter on approach and landing in earth's atmosphere and upon landing the two-piece rudder splays open to both sides of the stabilizer to act as an air brake to help slow the craft to a stop. Note the thermal protection system components with the white Advanced Flexible Reusable Surface Insulation Blanket and the black High-temperature Reusable Surface Insulation tiles along the outer edges (HRSI tiles). The marks seen on the HRSI tiles are injection point marks and holes for the application of waterproofing material. This view was taken from a service platform in the Orbiter Processing Facility at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Detail view of the vertical stabilizer of the Orbiter Discovery ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view of the vertical stabilizer of the Orbiter Discovery Discovery showing the thermal protection system components with the white Advanced Flexible Reusable Surface Insulation (AFSI) Blanket and the black High-temperature Reusable Surface Insulation (HRSI) tiles along the outer edges . The marks seen on the HRSI tiles are injection point marks and holes for the application of waterproofing material. This view also a good detailed view of the two-piece rudder which is used to control the yaw position of orbiter on approach and landing in earth's atmosphere and upon landing the two-piece rudder splays open to both sides of the stabilizer to act as an air brake to help slow the craft to a stop. This view was taken from a service platform in the Orbiter Processing Facility at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

Asteroid impact vs. Deccan eruptions: The origin of low magnetic susceptibility beds below the Cretaceous-Paleogene boundary revisited

NASA Astrophysics Data System (ADS)

Abrajevitch, Alexandra; Font, Eric; Florindo, Fabio; Roberts, Andrew P.

2015-11-01

The respective roles of an asteroid impact and Deccan Traps eruptions in biotic changes at the Cretaceous-Paleogene (K-Pg) boundary are still debated. In many shallow marine sediments from around the world, the K-Pg boundary is marked by a distinct clay layer that is often underlain by a several decimeter-thick low susceptibility zone. A previous study of the Gubbio section, Italy (Lowrie et al., 1990), attributed low magnetization intensity in this interval to post-depositional dissolution of ferrimagnetic minerals. Dissolution was thought to be a consequence of downward infiltration of reducing waters that resulted from rapid accumulation of organic matter produced by mass extinctions after the K-Pg event. We compare the magnetic properties of sediments from the Gubbio section with those of the Bidart section in southern France. The two sections are similar in their carbonate lithology and the presence of a boundary clay and low susceptibility zone. When compared to background Cretaceous sediments, the low susceptibility zone in both sections is marked by an absence of biogenic magnetite, a decrease in total ferrimagnetic mineral content, and a preferential loss of magnetite with respect to hematite - features that are consistent with reductive dissolution. However, unlike the Gubbio section, where the low susceptibility zone starts immediately below the boundary clay, the low susceptibility zone and the clay layer at Bidart are separated by a ∼4-cm carbonate interval that contains abundant biogenic magnetite. Such separation casts doubt on a causal link between the impact and sediment bleaching. More likely, the low susceptibility layer marks a different environmental event that preceded the impact. An episode of increased atmospheric and oceanic acidity associated with Deccan Traps volcanism that occurred well before the K-Pg impact is argued here to account for the distinct magnetic properties of the low susceptibility intervals.

Where's the Beaverhead beef?

NASA Astrophysics Data System (ADS)

Hargraves, R. B.

Only rare quartz grains with single-set planar (1013) deformation features (PDF's) are present in breccia dikes found in association with uniformly oriented shatter cones that occur over an area 8 x 25 km. This suggests that the Beaverhead shocked rocks come from only the outer part of the central uplift of what must have been a large (greater than 100 km diameter) complex impact structure. An impact event of this magnitude on continental crust (thought to have occurred in late Precambrian or ealy Paleozoic time) could be expected to punctuate local geologic history. Furthermore, although it may now be covered, its scar should remain despite all the considerable subsequent erosion/deposition and tectonism since the impact. The following are three large-scale singularities or anomalies that may reflect the event and mark its source. (1) The Lemhi Arch is a major structural uplift that occurred in late Proterozoic-early Paleozoic time in East Central Idaho and caused the erosion of at least 4 km of sedimentary cover. This may be directly related to the impact. (2) Of the many thrust sheets comprising the Cordilleran belt, the Cabin plate that carries the shocked rocks is unique in that it alone intersected the crystalline basement. It also now marks the apex of the Southwest Montana Recess in the Sevier front. The basement uplift remaining from the impact may have constituted a mechanical obstacle to the advancing thrust sheets in Cretaceous time, causing the recess. (3) What could be interpreted as a roughly circular aeromagnetic anomaly approx. 70 km in diameter can be discerned in the state aeromagnetic map centered about 20 km southeast of Challis, Idaho, in the Lost River range. It is in approximately the right place, and ignoring the possibility that the anomalies have diverse causes and the circular pattern is coincidental, it may mark what remains of the buried central uplift structure.

Adsorption of surfactant protein D from human respiratory secretions by carbon nanotubes and polystyrene nanoparticles depends on nanomaterial surface modification and size

PubMed Central

Marchetti, Magda; Shaffer, Milo S. P.; Zambianchi, Martina; Chen, Shu; Superti, Fabiana; Schwander, Stephan; Gow, Andrew; Zhang, Junfeng (Jim); Chung, Kian Fan; Ryan, Mary P.; Porter, Alexandra E.; Tetley, Teresa D.

2015-01-01

The alveolar respiratory unit constitutes one of the main targets of inhaled nanoparticles; the effect of engineered nanomaterials (NMs) on human health is largely unknown. Surfactant protein D (SP-D) is synthesized by alveolar type II epithelial cells and released into respiratory secretions; its main function is in immune defence, notably against inhaled microbes. SP-D also plays an important role in modulating an appropriate inflammatory response in the lung, and reduced SP-D is associated with a number of inflammatory lung diseases. Adsorption of SP-D to inhaled NMs may facilitate their removal via macrophage phagocytosis. This study addresses the hypothesis that the chemistry, size and surface modification of engineered NMs will impact on their interaction with, and adsorption of, SP-D. To this purpose, we have examined the interactions between SP-D in human lung lavage and two NMs, carbon nanotubes and polystyrene nanoparticles, with different surface functionalization. We have demonstrated that particle size, functionalization and concentration affect the adsorption of SP-D from human lung lavage. Functionalization with negatively charged groups enhanced the amount of SP-D binding. While SP-D binding would be expected to enhance macrophage phagocytosis, these results suggest that the degree of binding is markedly affected by the physicochemistry of the NM and that deposition of high levels of some nanoparticles within the alveolar unit might deplete SP-D levels and affect alveolar immune defence mechanisms. PMID:25533095

Role of Multicellular Aggregates in Biofilm Formation

PubMed Central

Kragh, Kasper N.; Hutchison, Jaime B.; Melaugh, Gavin; Rodesney, Chris; Roberts, Aled E. L.; Irie, Yasuhiko; Jensen, Peter Ø.; Diggle, Stephen P.; Allen, Rosalind J.

2016-01-01

ABSTRACT In traditional models of in vitro biofilm development, individual bacterial cells seed a surface, multiply, and mature into multicellular, three-dimensional structures. Much research has been devoted to elucidating the mechanisms governing the initial attachment of single cells to surfaces. However, in natural environments and during infection, bacterial cells tend to clump as multicellular aggregates, and biofilms can also slough off aggregates as a part of the dispersal process. This makes it likely that biofilms are often seeded by aggregates and single cells, yet how these aggregates impact biofilm initiation and development is not known. Here we use a combination of experimental and computational approaches to determine the relative fitness of single cells and preformed aggregates during early development of Pseudomonas aeruginosa biofilms. We find that the relative fitness of aggregates depends markedly on the density of surrounding single cells, i.e., the level of competition for growth resources. When competition between aggregates and single cells is low, an aggregate has a growth disadvantage because the aggregate interior has poor access to growth resources. However, if competition is high, aggregates exhibit higher fitness, because extending vertically above the surface gives cells at the top of aggregates better access to growth resources. Other advantages of seeding by aggregates, such as earlier switching to a biofilm-like phenotype and enhanced resilience toward antibiotics and immune response, may add to this ecological benefit. Our findings suggest that current models of biofilm formation should be reconsidered to incorporate the role of aggregates in biofilm initiation. PMID:27006463

Modulations of aerosol impacts on cloud microphysics induced by the warm Kuroshio Current under the East Asian winter monsoon

NASA Astrophysics Data System (ADS)

Koike, M.; Asano, N.; Nakamura, H.; Sakai, S.; Nagao, T. M.; Nakajima, T. Y.

2016-10-01

In our previous aircraft observations, the possible influence of high sea surface temperature (SST) along the Kuroshio Current on aerosol-cloud interactions over the western North Pacific was revealed. The cloud droplet number concentration (Nc) was found to increase with decreasing near-surface static stability (NSS), which was evaluated locally as the difference between the SST and surface air temperature (SAT). To explore the spatial and temporal extent to which this warm SST influence can be operative, the present study analyzed Nc values estimated from Moderate Resolution Imaging Spectroradiometer (MODIS) satellite measurements. The comparison of the local Nc values between the high and low SST - SAT days revealed a marked increase in Nc (up to a factor of 1.8) along the Kuroshio Current in the southern East China Sea, where particularly high SST - SAT values (up to 8 K) were observed in winter under monsoonal cold air outflows from the Asian Continent. This cold airflow destabilizes the atmospheric boundary layer, which leads to enhanced updraft velocities within the well-developed mixed layer and thus greater Nc. The monsoonal northwesterlies also bring a large amount of anthropogenic aerosols from the Asian continent that increase Nc in the first place. These results suggest that the same modulations of cloud microphysics can occur over other warm western boundary currents, including the Gulf Stream, under polluted cool continental airflows. Possibilities of influencing the cloud liquid water path are also discussed.

Parametric study of the physical properties of hydrate-bearing sand, silt, and clay sediments: 1. Electromagnetic properties

USGS Publications Warehouse

Lee, J.Y.; Santamarina, J.C.; Ruppel, C.

2010-01-01

The marked decrease in bulk electrical conductivity of sediments in the presence of gas hydrates has been used to interpret borehole electrical resistivity logs and, to a lesser extent, the results of controlled source electromagnetic surveys to constrain the spatial distribution and predicted concentration of gas hydrate in natural settings. Until now, an exhaustive laboratory data set that could be used to assess the impact of gas hydrate on the electromagnetic properties of different soils (sand, silt, and clay) at different effective stress and with different saturations of hydrate has been lacking. The laboratory results reported here are obtained using a standard geotechnical cell and the hydrate-formed tetrahydrofuran (THF), a liquid that is fully miscible in water and able to produce closely controlled saturations of hydrate from dissolved phase. Both permittivity and electrical conductivity are good indicators of the volume fraction of free water in the sediment, which is in turn dependent on hydrate saturation. Permittivity in the microwave frequency range is particularly predictive of free water content since it is barely affected by ionic concentration, pore structure, and surface conduction. Electrical conductivity (or resistivity) is less reliable for constraining water content or hydrate saturation: In addition to fluid-filled porosity, other factors, such as the ionic concentration of the pore fluid and possibly other conduction effects (e.g., surface conduction in high specific surface soils having low conductivity pore fluid), also influence electrical conductivity.

Spatial distribution of heavy metals in the surface soil of source-control stormwater infiltration devices - Inter-site comparison.

PubMed

Tedoldi, Damien; Chebbo, Ghassan; Pierlot, Daniel; Branchu, Philippe; Kovacs, Yves; Gromaire, Marie-Christine

2017-02-01

Stormwater runoff infiltration brings about some concerns regarding its potential impact on both soil and groundwater quality; besides, the fate of contaminants in source-control devices somewhat suffers from a lack of documentation. The present study was dedicated to assessing the spatial distribution of three heavy metals (copper, lead, zinc) in the surface soil of ten small-scale infiltration facilities, along with several physical parameters (soil moisture, volatile matter, variable thickness of the upper horizon). High-resolution samplings and in-situ measurements were undertaken, followed by X-ray fluorescence analyses and spatial interpolation. Highest metal accumulation was found in a relatively narrow area near the water inflow zone, from which concentrations markedly decreased with increasing distance. Maximum enrichment ratios amounted to >20 in the most contaminated sites. Heavy metal patterns give a time-integrated vision of the non-uniform infiltration fluxes, sedimentation processes and surface flow pathways within the devices. This element indicates that the lateral extent of contamination is mainly controlled by hydraulics. The evidenced spatial structure of soil concentrations restricts the area where remediation measures would be necessary in these systems, and suggests possible optimization of their hydraulic functioning towards an easier maintenance. Heterogeneous upper boundary conditions should be taken into account when studying the fate of micropollutants in infiltration facilities with either mathematical modeling or soil coring field surveys. Copyright © 2016 Elsevier B.V. All rights reserved.

Late Holocene Regression of the Northern Peruvian Coast Near Rio Chicama

NASA Astrophysics Data System (ADS)

Ramirez, M. T.; Goodbred, S. L.; Dillehay, T. D.; Quivira, M. P.

2008-12-01

Many Peruvian archaeological sites lie at the interface between an arid coastal desert, a rich marine ecosystem, and some of the tallest mountains in the Western Hemisphere, providing several unique environments within a small geographic area. While the region has supported civilizations since at least 6000BP, it has also been subject to a complex history of environmental impacts evident in the stratigraphy of the surrounding coastal environment. Most notable in the stratigraphy are El Nino flood events, providing the majority of sediment input to the coast, and tsunami events that are occasionally marked in the stratigraphic record. Such evidence for a paleotsunami appears to exist within a sequence of regressive Holocene shoreline deposits. This possible event is characterized by a planar erosional surface, dipping shallowly seaward, truncating the entire sequence of Holocene shorelines. The surface also consists of a lag of gravel that has been subsequently weathered by subaerial exposure to salt and sun. In addition there appears to be residual evidence of a similar, earlier event, most of which has been eroded from the record by the younger event. This entire sequence of shoreface deposits is situated approximately 2m above present mean sea level, and is suspected to be younger than 3000 years (pending radiocarbon dates), suggesting a rapid, recent Holocene regression in this region.

Follicle Depletion Provides a Permissive Environment for Ovarian Carcinogenesis

PubMed Central

Wang, Ying; Cai, Kathy Qi; Smith, Elizabeth R.; Yeasky, Toni M.; Moore, Robert; Ganjei-Azar, Parvin; Klein-Szanto, Andres J.; Godwin, Andrew K.; Hamilton, Thomas C.

2016-01-01

We modeled the etiology of postmenopausal biology on ovarian cancer risk using germ cell-deficient white-spotting variant (Wv) mice, incorporating oncogenic mutations. Ovarian cancer incidence is highest in peri- and postmenopausal women, and epidemiological studies have established the impact of reproductive factors on ovarian cancer risk. Menopause as a result of ovarian follicle depletion is thought to contribute to higher cancer risk. As a consequence of follicle depletion, female Wv mice develop ovarian tubular adenomas, a benign epithelial tumor corresponding to surface epithelial invaginations and papillomatosis frequently found in postmenopausal human ovaries. Lineage tracing using MISR2-Cre indicated that the tubular adenomas that developed in Wv mice were largely derived from the MISR2 lineage, which marked only a fraction of ovarian surface and oviduct epithelial cells in wild-type tissues. Deletion of p27, either heterozygous or homozygous, was able to convert the benign tubular adenomas into more proliferative tumors. Restricted deletion of p53 in Wv/Wv mice by either intrabursal injection of adenoviral Cre or inclusion of the MISR2-Cre transgene also resulted in augmented tumor growth. This finding suggests that follicle depletion provides a permissive ovarian environment for oncogenic transformation of epithelial cells, presenting a mechanism for the increased ovarian cancer risk in postmenopausal women. PMID:27354067

Snow Cover and Vegetation-Induced Decrease in Global Albedo From 2002 to 2016

NASA Astrophysics Data System (ADS)

Li, Qiuping; Ma, Mingguo; Wu, Xiaodan; Yang, Hong

2018-01-01

Land surface albedo is an essential parameter in regional and global climate models, and it is markedly influenced by land cover change. Variations in the albedo can affect the surface radiation budget and further impact the global climate. In this study, the interannual variation of albedo from 2002 to 2016 was estimated on the global scale using Moderate Resolution Imaging Spectroradiometer (MODIS) datasets. The presence and causes of the albedo changes for each specific region were also explored. From 2002 to 2016, the MODIS-based albedo decreased globally, snow cover declined by 0.970 (percent per pixel), while the seasonally integrated normalized difference vegetation index increased by 0.175. Some obvious increases in the albedo were detected in Central Asia, northeastern China, parts of the boreal forest in Canada, and the temperate steppe in North America. In contrast, noticeable decreases in the albedo were found in the Siberian tundra, Europe, southeastern Australia, and northeastern regions of North America. In the Northern Hemisphere, the greening trend at high latitudes made more contribution to the decline in the albedo. However, the dramatic fluctuation of snow-cover at midlatitudes predominated in the change of albedo. Our analysis can help to understand the roles that vegetation and snow cover play in the variation of albedo on global and regional scales.

Using measures of reproductive performance in estimating ecological risk to amphibians at J-Field, APG, Maryland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, M.S.; Whaley, J.E.; McCain, W.C.

1995-12-31

Current methods used for evaluating ecological risk to vertebrate receptors have come under increasing criticisms in that they neglect factors influencing population sustainability (i.e., predator avoidance and mate recognition behavior, reproductive performance, indirect effects, etc.). Further, recent declines in the densities of species of amphibians, combined with the fact that they are most exposed to soil, sediment, and surface water contaminants indicate that amphibians are conservative indicators of environmental stress. The authors marked 20 craters at J-Field, Edgewood Area, Aberdeen Proving Ground, Maryland, which were created from either high explosives, impact, or were excavated to receive surface water runoff frommore » hazardous waste sites. Each of these sites were chosen a priori and were habitats likely to be used by amphibians. Contaminants of concern were explosives, organochlorines (PCBs, chlordane, DDE), and some metals (As, Hg, Pb, Ba, Cd, Cr). The authors compared relative abundance and reproductive performance (defined by pooled egg mass weight) to measures of contaminant concentrations. Subsequent qualitative assessments of embryo development were also made. The authors contend that these methods are valuable in that they reduce uncertainty (including effects of selection), and provide a novel, yet feasible alternative to current ecological assessment methods.« less

In silico analysis of decomposed reflectances of C3 and C4 plants aiming at the effective assessment of crop needs

NASA Astrophysics Data System (ADS)

Baranoski, Gladimir V. G.; Van Leeuwen, Spencer; Chen, Tenn F.

2017-04-01

By separating the surface and subsurface components of foliar hyperspectral signatures using polarization optics, it is possible to enhance the remote discrimination of different plant species and optimize the assessment of different factors associated with their health status. These initiatives, in turn, can lead to higher crop yield and lower environmental impact. It is important to consider, however, that the main varieties of crops, represented by C3 (e.g., soy) and C4 (e.g., maize) plants, have markedly distinct morphological characteristics. Accordingly, the influence of these characteristics on their interactions with impinging light may affect the selection of optimal probe wavelengths for specific applications making use of combined hyperspectral and polarization measurements. In this paper, we compare the sensitivity of the total (including surface and subsurface components) and subsurface reflectance responses of C3 and C4 plants to different spectral and geometrical light incidence conditions. This investigation is supported by measured biophysical data and predictive light transport simulations. The results of our comparisons indicate that the total and subsurface reflectance responses of C3 and C4 plants depict well-defined patterns of sensitivity for varying illumination conditions. We believe that these patterns should be considered in the design of high-fidelity crop discrimination and monitoring procedures.

Land Fire impacts assessment on the Rice Watershed, California. 2007

NASA Astrophysics Data System (ADS)

Zahraei, A.; Imam, B.; Sorooshian, S.

2009-12-01

Burn impacts assessment is a key factor for the post-fire disaster management. For example, assessing wildfire impacts on vegetation is an important component of improving the prediction of hydrologic and ecologic impacts of wildfires within the affected watershed. Many studies have analyzed satellite derived indices of vegetation vigor as indicator of burning effects. This poster reports a study in which Landsat (TM) data was used to compute three indices, NDVI, MASAVI and NBR, which are commonly used in assessing wildfire impacts. The study focused on the Rice watershed southern California, which was affected by a major wildfire in the 2007 fire season. A series of before and after Landsat images were used to evaluate these indices evaluated before and after the wildfire. Comparison between the three indices reveals that the affects of the fire were not very prominently present in the Satellite observation due to the length of time separating the fire from the next available Lansat scene. Such separation may include a period of vegetation recovery. However, when compared with the scenes from the previous year, but for the same season, post fire vegetation show marked differences from pre-fire conditions. The ability of NDVI, MSAVI and NBR to monitor post-fire impacts on vegetation is further evaluated by comparing precipitation patterns in 2006 and 2007, which may shed more light on whether the marked difference in these indices are due to dry/wet differences or to the impacts of fire. NDVI shows more reliability and better representation of both long-term and short-term impacts of wild-fire.

Failure Analysis to Identify Thermal Runaway of Bypass Diodes in Fielded Modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Chuanxiao, Uchida, Yasunori; Johnston, Steve; Hacke, Peter

We studied a bypass diode recuperated from fielded modules in a rooftop installation to determine the failure mechanism. The field-failed diode showed similar characteristics to thermal runaway, specifically X-ray tomography evidence of migrated metal. We also observed burn marks on the silicon surface like those lab-stressed for thermal runaway. Reaction products are more soluble than silicon and the surface is oxygen rich.

Increasing amounts of chemical weed control increase growth of white ash, white oak, and black walnut saplings in a tall fescue sod

Treesearch

Jonathan D. Carlisle; Wayne A. Geyer; J. W. Van Sambeek

2003-01-01

Effective weed control in young deciduous plantations is often prescribed to enhance survivability and growth (Bey and others 1975). Chemical weed control often employs broadcast, strip, and spot applications that markedly affect the ground surface area treated. Our study investigates the effect of four levels of treated surface area of a tank mix of glyphosate and...

Electrochemical Micromachining with Fiber Laser Masking for 304 Stainless Steel

NASA Astrophysics Data System (ADS)

Li, Xiaohai; Wang, Shuming; Wang, Dong; Tong, Han

2017-10-01

In order to fabricate micro structure, the combined machining of electrochemical micro machining (EMM) and laser masking for 304 stainless steel was studied. A device of composite machining of EMM with laser masking was developed, and the experiments of EMM with laser masking were carried out. First, by marking pattern with fiber laser on the surface of 304 stainless steel, the special masking layer can be formed. Through X ray photoelectron spectroscopy (XPS), the corrosion resistance of laser masking layer was analyzed. It is proved by XPS that the iron oxide and chromium oxide on the surface of stainless steel generates due to air oxidation when laser scanning heats. Second, the localization and precision of EMM are improved, since the marking patterns forming on the surface of stainless steel by laser masking play a protective role in the process of subsequent EMM when the appropriate parameters of EMM are selected. At last, the shape and the roughness of the machined samples were measured by SEM and optical profilometer and analyzed. The results show that the rapid fabrication of micro structures on the 304 stainless steel surface can be achieved by EMM with fiber laser masking, which has a good prospect in the field of micro machining.

Laser material micro-working (LMμW): some new surface processes

NASA Astrophysics Data System (ADS)

Daurelio, G.; D'Alonzo, M.

2007-05-01

On the last recent years many new Laser Surface Processes have been studied and tested in the field of the L.M. μW. - Laser Material Micro Working. Still today many of these "young" processes are to study and more and more searches are dedicated to they. These are the Marking, Texturing, Fine Texturing, Filling, Polishing, Micro Shot-Penning, Silking and Colouring. This experimental work reports the results obtained in the field of the Laser Surface Fine Texturing on AISI 304 and 430 Stainless Steels by using a Marking System, that is a Nd:YAG Laser, VECTORMARK type by TRUMPH ( D ). So some new laser surface finishes, called by Authors, - Effetto tessuto, con trama e ordito (Woven effect, with weft and warp) - Effetto pelle scamosciata ( Effect shammy leather ) - Effetto pelle uncinata ( Effect hooked skin ) - Effetto pelle unghiata ( Effect skin looking like scratch ) - Effetto pelle damascata ( Effect damask skin ) - Effetto speculare , ottonato ( Specular effect, looking like brass ) Effetto speculare, bronzato ( specular effect looking like bronze ) - Effetto speculare, argenteo ( specular, looking like silver effect ) - Effetto speculare, ramato ( Specular effect, looking like copper ), Effetto Speculare, dorato ( Specular effect, looking like gold ) - Effetto speculare , dorato, a raggiera ( Specular effect, looking like gold, to aureole) , were carried out. The work is still in progress.

Scanning electron microscopic and X-ray micro analysis on tooth enamel exposed to alkaline agents.

PubMed

Taubee, Fabian; Steiniger, Frank; Nietzsche, Sandor; Norén, Jörgen G

2010-01-01

The background of this study comprises two clinical cases, where patients exposed to aerosols of an alkaline and surface active cleaning agent developed loss of enamel substance on their teeth, further resulting in loss of teeth and partially destroyed soft tissues. The alkaline cleaning agent consisted of potassium hydroxide and various surfactants. The purpose of this study was to investigate possible changes in morphology and composition in human teeth enamel exposed to alkaline solutions, by means of X-ray micro analysis (XRMA), FTIR-spectroscopic analyses and scanning electron microscopy (SEM). Extracted premolars, exposed to potassium hydroxide solutions and alkaline cleaning solution,were analyzed by means of XRMA and SEM. Enamel powder, exposed to cleaning solution, was analyzed by means of FTIR. The SEM analysis revealed an increased porosity of the enamel surface and partially loss of enamel substance after exposure to alkaline solutions. The XRMA analyses revealed a decrease in carbon concentration while phosphorous and calcium showed no marked changes. The FTIR analyses showed no significant changes in peak heights or peak positions for phosphate, carbonate or hydroxide. It was concluded that human teeth enamel exposed to alkaline solutions showed loss of organic substance, marked pores in enamel surface and loss of substance in the enamel surface.

Foreign body impaction in the esophagus: are there underlying motor disorders?

PubMed

Mazzadi, S; Salis, G B; García, A; Iannicillo, H; Fucile, V; Chiocca, J C

2017-11-01

Compared with the control group, the impacted subjects presented marked reduction in amplitude and duration of esophageal contraction in the proximal esophagus. These motor disorders could be responsible for the foreign body impaction in the esophagus. However, we believe this patient group should be further studied by 24-hour esophageal manometry to reach a more accurate diagnosis by studying each patient's entire circadian cycle. © 1998 International Society for Diseases of the Esophagus/Harcourt Brace & Co. Ltd

Effect of SiC particle impact nano-texturing on tribological performance of 304L stainless steel

NASA Astrophysics Data System (ADS)

Lorenzo-Martin, C.; Ajayi, O. O.

2014-10-01

Topographical features on sliding contact surfaces are known to have a significant impact on friction and wear. Indeed, various forms of surface texturing are being used to improve and/or control the tribological performance of sliding surfaces. In this paper, the effect of random surface texturing produced by a mechanical impact process is studied for friction and wear behavior of 304L stainless steel (SS) under dry and marginal oil lubrication. The surface processing was applied to 304L SS flat specimens and tested under reciprocating ball-on-flat sliding contact, with a 440C stainless steel ball. Under dry contact, the impact textured surface exhibited two order of magnitude lower wear than the isotropically ground surface of the same material. After 1500 s of sliding and wearing through of the processed surface layer following occurring of scuffing, the impact textured surface underwent a transition in wear and friction behavior. Under marginal oil lubrication, however, no such transition occurred, and the wear for the impact textured surface was consistently two orders of magnitude lower than that for the ground material. Mechanisms for the tribological performance enhancement are proposed.

Geochemical and petrographic studies of melt-rich breccias from the Chicxulub crater

NASA Astrophysics Data System (ADS)

Vera-Sanchez, P.; Urrutia-Fucugauchi, J.; Morton-Bermea, O.; Soler-Arechalde, A.; Reyes-Salas, M.; Lozano-Santamaria, R.; Linares-Lopez, C.; Rebolledo-Vieyra, M.

2003-04-01

The proposal by Alvarez et al. (1980) for an extraterrestrial bolide impact marking the Cretaceous/Tertiary boundary was based on the anomalous Ir content in Italian and Danish K/T clay layers. The clay layer with a worldwide distribution and enriched in platinum group elements, shocked quartz and other impact-generated features has come to be interpreted as the global ejecta layer produced by a large impact that formed the Chicxulub crater. The ~200 km diameter crater is located in the carbonate platform of northwestern Yucatan peninsula, Mexico. The crater is covered by a thick sequence of Tertiary sediments, with no surface exposures. The National University of Mexico conducted a drilling program with continuous core recovery, in which three boreholes (UNAM wells 5, 6 and 7) sampled the impact breccia sequences. Deeper drilling inside the carter has been carried out as part of the ICDP program with drilling of the Yaxcopoil-1 borehole, which also cored a section of the impact breccias. The Yaxcopoil-1 borehole has been completed as part of the Chicxulub Scientific Drilling Project. In this work, we report on the geochemical and petrographic studies of selected samples from the impact breccia sequence recovered in the Yaxcopoil-1 borehole inside the Chicxulub crater. One of the major questions emerging after the interpretation of Chicxulub as the K/T boundary impact site and its link to the global ejecta layer has been the nature of the impacting body. Studies have addressed this question from distinct fields, including investigation of the ejecta deposits near and far from the crater, from the crater itself, from impact records on the Moon and other bodies, searching for surviving fragments in K/T boundary sections, etc. The search for material with a possible small component associated to the impactor could open unique research opportunities to further understand the impact event. The melt breccia samples examined exhibit different textures and chemical composition, suggesting a complex composition. Rare earth element plots for the various fragments are on the other hand similar. We report the initial results of the petrographic, microprobe, ICP-MS, X-ray fluorescence and X-ray diffraction studies.

ARC-1979-AC79-7095

NASA Image and Video Library

1979-07-11

Range : 312, 000 kilometers (195,000 miles) This photo of Ganymede (Ice Giant) was taken from Voyager 2 and shows features down to about 5 to 6 kilometers across. Different types of terrain common on Ganymede's surface are visible. The boundary of the largest region of dark ancient terrain on Ganymede can be seen to the east (right), revealing some of the light linear features which may be all that remains of a large ancient impact structure similar to the large ring structure on Callisto. The broad light regions running through the image are the typical grooved structures seen within another example of what might be evidence of large scale lateral motion in Ganymede's crust. The band of grooved terrain (about 100 kilometers wide) in this region appears to be offset by 50 kilometers or more on the left hand edge by a linear feature perpendicular to it. A feature similar to this one was previously discovered by Voyager 1. These are the first clear examples of strike-slip style faulting on any planet other than Earth. Many examples of craters of all ages can be seen in this image, ranging from fresh, bright ray craters to large, subdued circular markings thought to be the 'scars' of large ancient impacts that have been flatteded by glacier-like flows.

An Impact Evaluation of a Federal Mine Safety Training Regulation on Injury Rates Among US Stone, Sand, and Gravel Mine Workers: An Interrupted Time-Series Analysis

PubMed Central

Windsor, Richard

2010-01-01

Objectives. We evaluated the impact of a safety training regulation, implemented by the US Department of Labor's Mine Safety and Health Administration (MSHA) in 1999, on injury rates at stone, sand, and gravel mining operations. Methods. We applied a time-series design and analyses with quarterly counts of nonfatal injuries and employment hours from 7998 surface aggregate mines from 1995 through 2006. Covariates included standard industrial classification codes, ownership, and injury severity. Results. Overall crude rates of injuries declined over the 12-year period. Reductions in incident rates for medical treatment only, restricted duty, and lost-time injuries were consistent with temporal trends and provided no evidence of an intervention effect attributable to the MSHA regulation. Rates of permanently disabling injuries (PDIs) declined markedly. Regression analyses documented a statistically significant reduction in the risk rate in the postintervention time period (risk rate = 0.591; 95% confidence interval = 0.529, 0.661). Conclusions. Although a causal relationship between the regulatory intervention and the decline in the rate of PDIs is plausible, inconsistency in the results with the other injury-severity categories preclude attributing the observed outcome to the MSHA regulation. Further analyses of these data are needed. PMID:20466960

An impact evaluation of a federal mine safety training regulation on injury rates among US stone, sand, and gravel mine workers: an interrupted time-series analysis.

PubMed

Monforton, Celeste; Windsor, Richard

2010-07-01

We evaluated the impact of a safety training regulation, implemented by the US Department of Labor's Mine Safety and Health Administration (MSHA) in 1999, on injury rates at stone, sand, and gravel mining operations. We applied a time-series design and analyses with quarterly counts of nonfatal injuries and employment hours from 7998 surface aggregate mines from 1995 through 2006. Covariates included standard industrial classification codes, ownership, and injury severity. Overall crude rates of injuries declined over the 12-year period. Reductions in incident rates for medical treatment only, restricted duty, and lost-time injuries were consistent with temporal trends and provided no evidence of an intervention effect attributable to the MSHA regulation. Rates of permanently disabling injuries (PDIs) declined markedly. Regression analyses documented a statistically significant reduction in the risk rate in the postintervention time period (risk rate = 0.591; 95% confidence interval = 0.529, 0.661). Although a causal relationship between the regulatory intervention and the decline in the rate of PDIs is plausible, inconsistency in the results with the other injury-severity categories preclude attributing the observed outcome to the MSHA regulation. Further analyses of these data are needed.

Strangelove ocean at era boundaries, terrestrial or extraterrestrial cause

NASA Astrophysics Data System (ADS)

Hsue, Kenneth J.

Negative perturbations in carbon-isotope value of calcite in pelagic sediments were found at times of biotic crisis, marking horizons which are, or were proposed as era boundaries: Cretaceous/Tertiary (K/T), Permian/Triassic (P/T), and Precambrian/Cambrian (PreC/C). The anomaly was also found at several other mass-extinction horizons, such as terminal Ordovician, Frasnian-Famenian, etc. Studies of K/T boundary indicate that only the planktic fraction of the sediments has the negative isotope anomaly, whereas the benthic fraction has the same value across the boundary. This geochemical signal is thus considered a record of strangelove ocean, or an ocean where isotope fractionation of dissolved carbonate ions in surface waters (by biotic function of planktic organisms) has been significantly reduced because of the drastic reduction of the biomass in the oceans. The reduction of marine biomass at each of the era boundaries was related to chemical pollution of the oceans as a consequence of a catastrophic event; a pH decrease of 0.5 could inhibit the fertility of planktons. Studies of earthquakes, volcanic eruptions, and meteorite-impact occurrences have indicated a linearly inverse log/log relationship between the magnitude and frequency of events. The frequency of era boundaries in geologic history supports the postulate that the rare events causing those biotic crises were large bolide-impacts.

Strangelove ocean at era boundaries, terrestrial or extraterrestrial cause

NASA Technical Reports Server (NTRS)

Hsue, Kenneth J.

1988-01-01

Negative perturbations in carbon-isotope value of calcite in pelagic sediments were found at times of biotic crisis, marking horizons which are, or were proposed as era boundaries: Cretaceous/Tertiary (K/T), Permian/Triassic (P/T), and Precambrian/Cambrian (PreC/C). The anomaly was also found at several other mass-extinction horizons, such as terminal Ordovician, Frasnian-Famenian, etc. Studies of K/T boundary indicate that only the planktic fraction of the sediments has the negative isotope anomaly, whereas the benthic fraction has the same value across the boundary. This geochemical signal is thus considered a record of strangelove ocean, or an ocean where isotope fractionation of dissolved carbonate ions in surface waters (by biotic function of planktic organisms) has been significantly reduced because of the drastic reduction of the biomass in the oceans. The reduction of marine biomass at each of the era boundaries was related to chemical pollution of the oceans as a consequence of a catastrophic event; a pH decrease of 0.5 could inhibit the fertility of planktons. Studies of earthquakes, volcanic eruptions, and meteorite-impact occurrences have indicated a linearly inverse log/log relationship between the magnitude and frequency of events. The frequency of era boundaries in geologic history supports the postulate that the rare events causing those biotic crises were large bolide-impacts.

Biological control of surface temperature in the Arabian Sea

NASA Technical Reports Server (NTRS)

Sathyendranath, Shubha; Gouveia, Albert D.; Shetye, Satish R.; Ravindran, P.; Platt, Trevor

1991-01-01

In the Arabian Sea, the southwest monsoon promotes seasonal upwelling of deep water, which supplies nutrients to the surface layer and leads to a marked increase in phytoplankton growth. Remotely sensed data on ocean color are used here to show that the resulting distribution of phytoplankton exerts a controlling influence on the seasonal evolution of sea surface temperature. This results in a corresponding modification of ocean-atmosphere heat exchange on regional and seasonal scales. It is shown that this biological mechanism may provide an important regulating influence on ocean-atmosphere interactions.

Mars - Hellas Planitia gravity analysis

NASA Technical Reports Server (NTRS)

Sjogren, W. L.; Wimberley, R. N.

1981-01-01

Doppler radio tracking data from Viking Orbiter 1 has provided new detailed observations of gravity variations over Hellas Planitia. Line-of-sight Bouguer gravity definitely indicates that isostatic adjustment has occurred. Two theoretical models were tested to obtain fits to the gravity data. Results for a surface deficit model, and a model with a surface deficit and a mass excess at depth are displayed. The mass-at-depth model produced very marked improvement in the data fit as compared to the surface deficit model. The optimum depth for the mass excess is 130 km.