A new technique for Auger analysis of surface species subject to electron-induced desorption

NASA Technical Reports Server (NTRS)

Pepper, S. V.

1973-01-01

A method is presented to observe surface species subject to electron-induced desorption by Auger electron spectroscopy. The surface to be examined is moved under the electron beam at constant velocity, establishing a time independent condition and eliminating the time response of the electron spectrometer as a limiting factor. The dependence of the Auger signal on the surface velocity, incident electron current, beam diameter, and desorption cross section are analyzed. The method is illustrated by the Auger analysis of PTFE, in which the fluorine is removed by electron induced desorption.

[Diversity of Bacillus species inhabiting on the surface and endophyte of lichens collected from Wuyi Mountain].

PubMed

Ge, Cibin; Liu, Bo; Che, Jianmei; Chen, Meichun; Liu, Guohong; Wei, Jiangchun

2015-05-04

The present work reported the isolation, identification and diversity of Bacillus species colonizing on the surface and endophyte in lichens collected from Wuyi Mountain. Nine lichen samples of Evernia, Stereocaulon, Menegazzia and other 6 genera belonging to 7 families were collected from Wuyi mountain nature reserve. The bacillus-like species colonizing on the surface and endophyte in these lichens were isolated and identified by 16S rRNA gene sequence analysis. There was no bacillus-like species isolated from Evernia, Ramalina and Lecarona. A total of 34 bacillus-like bacteria were isolated from another 6 lichen samples. These bacteria were identified as 24 species and were classified into Bacillus, Paenibacillus, Brevibacillus, Lysinibacillus and Viridiibacillus. Paenibacillus and Bacillus are the dominant genera, and accounting for 41. 2% and 35. 3% of all isolated bacteria respectively. Brevibacillus, Lysinibacillus and Viridiibacillu were first reported being isolated from lichens. There were different species and quantity of bacillus colonizing on the surface and endophyte in different lichens. The quantity of bacillus colonizing on the surface of Physcia was more than 3.85 x 10(6) cfu/g and was the largest in the isolated bacteria, while the species of bacillus colonizing on the surface and endophyte in Stereocaulon was the most abundant. Most of the isolated bacteria were colonizing on (in) one lichen genera, but Paenibacillus taichungensis, Paenibacillus odorifer, Brevibacillus agri, Lysinibacillus xylanilyticus was respectively colonizing on (in) 2-3 lichen genera and Bacillus mycoides was colonizing on (in) Menegazzia, Cladonia Physcia, and Stereocaulon. There are species and quantity diversity of bacillus colonizing on (in) lichens.

Probing the surface of γ-Al2O3 by oxygen-17 dynamic nuclear polarization enhanced solid-state NMR spectroscopy.

PubMed

Li, Wenzheng; Wang, Qiang; Xu, Jun; Aussenac, Fabien; Qi, Guodong; Zhao, Xingling; Gao, Pan; Wang, Chao; Deng, Feng

2018-06-14

γ-Al2O3 is an important catalyst and catalyst support of industrial interest. Its acid/base characteristics are correlated to the surface structure, which has always been an issue of concern. In this work, the complex (sub-)surface oxygen species on surface-selectively labelled γ-Al2O3 were probed by 17O dynamic nuclear polarization surface-enhanced NMR spectroscopy (DNP-SENS). Direct 17O MAS and indirect 1H-17O cross-polarization (CP)/MAS DNP experiments enable observation of the (sub-)surface bare oxygen species and hydroxyl groups. In particular, a two-dimensional (2D) 17O 3QMAS DNP spectrum was for the first time achieved for γ-Al2O3, in which two O(Al)4 and one O(Al)3 bare oxygen species were identified. The 17O isotropic chemical shifts (δcs) vary from 56.7 to 81.0 ppm and the quadrupolar coupling constants (CQ) range from 0.6 to 2.5 MHz for the three oxygen species. The coordinatively unsaturated O(Al)3 species is characterized by a higher field chemical shift (56.7 ppm) and the largest CQ value (2.5 MHz) among these oxygen sites. 2D 1H → 17O HETCOR DNP experiments allow us to discriminate three bridging (Aln)-μ2-OH and two terminal (Aln)-μ1-OH hydroxyl groups. The structural features of the bare oxygen species and hydroxyl groups are similar for the γ-Al2O3 samples isotopically labelled by 17O2 gas or H217O. The results presented here show that the combination of surface-selective labelling and DNP-SENS is an effective approach for characterizing oxides with complex surface species.

Reactions of aqueous aluminum species at mineral surfaces

USGS Publications Warehouse

Brown, David Wayne; Hem, John David

1975-01-01

Aqueous aluminum solutions containing 4.5 ? 10 4 molar aluminum in 0.01 molar NaC104 were partly neutralized with NaOH to give OH:A1 mole ratios from 1.40 to 2.76. Measured amounts of montmorillonite, kaolinite, volcanic ash, or feldspathic sand were added to provide an area of inert surface. Reactions that occurred during 100 days of aging were compared with those in similar solutions without added surfaces, studied in earlier work. Adsorption of monomeric species Al(H20)6+3, AlOH(H2O)5+2, and Al(OH)2(H2O 4? on the added surfaces follows a cation exchange mass law equilibrium model, and adsorption is essentially complete in 1 hour. Only minor changes in monomeric aluminum species occurred after that. Rapid adsorption of polynuclear aluminum hydroxide species also occurs and follows the pattern of the Langmuir adsorption isotherm. In the absence of surfaces, the polynuclear ions slowly increase in size and become microcrystalline gibbsite during aging. Electron micrographs showed microcrystalline gibbsite was present or surfaces after aging only 2 days. However, the analytical data suggest this material must have been adsorbed after it had already attained a near-crystalline state. Adsorbed polynuclear aluminum hydroxide species were not extensively converted to microcrystalline gibbsite during 100 days of aging.

The adsorption and thermal decomposition of PH 3 on Si(111)-(7 × 7)

NASA Astrophysics Data System (ADS)

Taylor, P. A.; Wallace, R. M.; Choyke, W. J.; Yates, J. T.

1990-11-01

The adsorption of PH 3, on Si(111)-(7 × 7) has been studied by Auger electron spectroscopy and temperature programmed desorption. PH 3 was found to exhibit two kinds of behavior on the surface. A small surface coverage of molecularly adsorbed PH 3 desorbs without any dissociative surface chemistry. For the majority of the adsorbed PH x species (3 ⩾ x ⩾ 1) dissociation occurs to form P(a) and H(a). At 120 K, PH 3 initially adsorbs as the reactive species with a sticking coefficient of S ≅ 1 up to ˜75% saturation. The reactive PH x species surface concentration saturates at (1.9 ± 0.3) × 10 14 PH x cm -2. Surface H(a), produc thermal decomposition, desorbs as H 2(g) at T > 700 K., and P(a) desorbs as P 2(g) at T > 900 K. Capping the Si-dangling bonds with atomic deuterium prevents PH 3 adsorption, indicating that the dangling bonds are the PH 3 adsorption sites. Isotopic studies involving Si-D surface species mixed with adsorbed PH x species indicate that PH 3 desorption does not occur through a recombination process. Finally, additional PH 3 may be adsorbed if the surface hydrogen produced by dissociation of PH 3 is removed. Evidence for P penetration into bulk Si(111) at 875 K is presented.

Organic cloud condensation nuclei: the effect of phase, surface tension, trace soluble species, and oxidative processing on particle activation.

NASA Astrophysics Data System (ADS)

Broekhuizen, K. E.; Thornberry, T.; Abbatt, J. P.

2003-12-01

The ability of organic aerosols to act as cloud condensation nuclei (CCN) will be discussed. A variety of laboratory experiments will be presented which address several key questions concerning organic particle activation. Does the particle phase impact activation? How does surface tension play a role and can a trace amount of a surface active species impact activation? Does a trace amount of a highly soluble species impact the activation of organic particles of moderate to low solubility? Can the activation properties of organic aerosols be enhanced through oxidative processing? To systematically address these issues, the CCN activity of various diacids such as oxalic, malonic, succinic, adipic and azelaic acid have been studied, as well as the addition of trace amounts of nonanoic acid and ammonium sulfate to examine the roles of surface active and soluble species, respectively. The first examination of the role of oxidative processing on CCN activity has involved investigating the effect of ozone oxidation on the activity of oleic acid particles.

Solutions for Reacting and Nonreacting Viscous Shock Layers with Multicomponent Diffusion and Mass Injection. Ph.D. Thesis - Virginia Polytechnic Inst. and State Univ.

NASA Technical Reports Server (NTRS)

Moss, J. N.

1971-01-01

Numerical solutions are presented for the viscous shocklayer equations where the chemistry is treated as being either frozen, equilibrium, or nonequilibrium. Also the effects of the diffusion model, surface catalyticity, and mass injection on surface transport and flow parameters are considered. The equilibrium calculations for air species using multicomponent: diffusion provide solutions previously unavailable. The viscous shock-layer equations are solved by using an implicit finite-difference scheme. The flow is treated as a mixture of inert and thermally perfect species. Also the flow is assumed to be in vibrational equilibrium. All calculations are for a 45 deg hyperboloid. The flight conditions are those for various altitudes and velocities in the earth's atmosphere. Data are presented showing the effects of the chemical models; diffusion models; surface catalyticity; and mass injection of air, water, and ablation products on heat transfer; skin friction; shock stand-off distance; wall pressure distribution; and tangential velocity, temperature, and species profiles.

Revision of the Lima clade (Miconia sect. Lima, Miconieae, Melastomataceae) of the Greater Antilles

PubMed Central

Majure, Lucas C.; Bécquer, Eldis R.; Judd, Walter S.

2016-01-01

Abstract Miconia sect. Lima is an entirely Greater Antillean clade that consists of 19 known species of shrubs and small trees, which were previously recognized under the polyphyletic genera Leandra and Ossaea. The highest species richness in the clade is represented on Cuba (10 species), followed by Hispaniola (8 species) and then Jamaica (1 species). Here we present a taxonomic revision of the clade based on the study of species in the field, herbarium specimens, as well as a DNA-based phylogeny reconstruction. The Lima clade most likely originated on Cuba and then spread to Jamaica once and Hispaniola multiple times. Species of this clade can be recognized by the well developed bulla-based hairs of the adaxial leaf surface, as well as the clavate-dendritic hairs produced along the primary, secondary and tertiary veins of the adaxial leaf surface, mostly towards the leaf base, terminal inflorescences, acute petal apices, slightly bulla-based hairs produced subapically along the petal abaxial surface, and anthers with a dorso-basal appendage and a single, dorsally oriented pore. Descriptions, synonymies, along with distribution maps and illustrations/figures, are given for each species. Miconia pagnolensis sp. nov. is newly described in this revision. PMID:27829802

The utility of polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) in surface and in situ studies: new data processing and presentation approach.

PubMed

Monyoncho, Evans A; Zamlynny, Vlad; Woo, Tom K; Baranova, Elena A

2018-05-29

Infrared spectroscopy is a powerful non-destructive technique for the identification and quantification of organic molecules widely used in scientific studies. For many years, efforts have been made to adopt this technique for the in situ monitoring of reactions. From these efforts, polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) was developed three decades ago. Unfortunately, because of the complexity of data processing and interpretation, PM-IRRAS had been avoided in lieu of the single potential alteration infrared spectroscopy (SPAIRS) and subtractively normalized interfacial Fourier transform infrared (SNIFTIR). In this work, we present a new approach for PM-IRRAS data processing and presentation, which provides more insight into in situ and surface studies besides dramatically improving the S/N. In this new approach, we recommend three complementary methods of data treatment (eqn (7), (9) and (10)) as the new protocols for presenting PM-IRRAS data. These equations are robust in visualising the surface processes at the solid-liquid and solid-gas interphases. Eqn (7) contrasts the surface adsorbed species with respect to the isotropic background with or without the influence of the applied potential. Eqn (9) highlights the surface potential-driven changes between the sample and the reference spectra. Eqn (10) focuses on the bulk-phase (solution/gas and surface species) potential-driven changes between the sample and the reference spectra, and hence it can be used to track the production of species, which desorb from the surface upon their formation. Examples of ethanol electro-oxidation reaction are provided as a test system for in situ studies and PVP deposited on glassy carbon for thin-film studies to illustrate the utility of the new PM-IRRAS data handling protocol, which is poised to improve the understanding of the chemistry and physics of surface processes.

A new species of Limnonectes (Amphibia: Anura: Dicroglossidae) from Vietnam.

PubMed

Pham, Cuong The; Le, Minh Duc; Nguyen, Tao Thien; Ziegler, Thomas; Wu, Zheng Jun; Nguyen, Truong Quang

2017-05-24

A new species of Limnonectes is described from northeastern Vietnam based on morphological and molecular differences. Morphologically, the new species is distinguishable from its congeners on the basis of a combination of the following diagnostic characters: Large size (SVL 50.1-68.9 in males, 45.5-63.0 mm in females); males with moderately enlarged head (HL/SVL 0.48), head longer than wide; vomerine teeth present; external vocal sacs absent; rostral length short (RL/SVL 0.16 in males, 0.15 in females); tympanum distinct (TD/ED 0.63 in males, 0.60 in females); dorsal surface of head, body and flanks with flattened tubercles; dorsal surface of tibia possessing small tubercles; supratympanic fold present; dorsolateral fold absent; webbing formula I0-0II0-1/3III0-1/3IV1/2-0V; in life, dorsum yellowish brown with a dark brown marking; throat and chest white with dark brown marking; ventral surface of fore and hind limbs as well as belly white. In phylogenetic analyses, the new species is placed as the sister taxon to Limnonectes fujianensis with strong statistical support in all analyses.

Mechanism of Phosphine Dissociation on the Si(001) Surface

NASA Astrophysics Data System (ADS)

Warschkow, Oliver; Schofield, Steven R.; Smith, Phil V.

2005-03-01

The continued down-scaling of electronic devices to the atomic scale increasingly requires an atomic-level understanding of the elementary processes of semiconductor doping. We present a combined experimental and theoretical investigation into the dissociation mechanism of phosphine (PH3) on the Si(001) surface. As reported by us elsewhere in this conference, a number of prominent intermediate species of PH3 dissociation observed in STM experiments have been structurally characterized as PH2+H, PH+2H and P+3H species respectively. In this poster we present detailed quantum chemical calculations of these and other short-lived intermediates as well as the transition (kinetic) barriers between them. This leads us to formulate a step-by-step mechanism for the complete dissociation of PH3 on the Si(001) surface.

Surface-slip equations for multicomponent nonequilibrium air flow

NASA Technical Reports Server (NTRS)

Gupta, R. N.; Scott, C. D.; Moss, J. N.

1985-01-01

Equations are presented for the surface-slip (or jump) values of species concentration, pressure, velocity, and temperature in the low-Reynolds number, high-altitude flight regime of a space vehicle. The equations are obtained from closed form solutions of the mass, momentum, and energy flux equations using the Chapman-Enskog velocity distribution function. This function represents a solution of the Boltzmann equation in the Navier-Stokes approximation. The analysis, obtained for nonequilibrium multicomponent air flow, includes the finite-rate surface catalytic recombination and changes in the internal energy during reflection from the surface. Expressions for the various slip quantities were obtained in a form which can be employed in flowfield computations. A consistent set of equations is provided for multicomponent, binary, and single species mixtures. Expression is also provided for the finite-rate, species-concentration boundary condition for a multicomponent mixture in absence of slip.

Surface-slip equations for multicomponent, nonequilibrium air flow

NASA Technical Reports Server (NTRS)

Gupta, Roop N.; Scott, Carl D.; Moss, James N.; Goglia, Gene

1985-01-01

Equations are presented for the surface slip (or jump) values of species concentration, pressure, velocity, and temperature in the low-Reynolds-number, high-altitude flight regime of a space vehicle. These are obtained from closed-form solutions of the mass, momentum, and energy flux equations using the Chapman-Enskog velocity distribution function. This function represents a solution of the Boltzmann equation in the Navier-Stokes approximation. The analysis, obtained for nonequilibrium multicomponent air flow, includes the finite-rate surface catalytic recombination and changes in the internal energy during reflection from the surface. Expressions for the various slip quantities have been obtained in a form which can readily be employed in flow-field computations. A consistent set of equations is provided for multicomponent, binary, and single species mixtures. Expression is also provided for the finite-rate species-concentration boundary condition for a multicomponent mixture in absence of slip.

Maximally resolved anharmonic OH vibrational spectrum of the water/ZnO(101 \\xAF 0) interface from a high-dimensional neural network potential

NASA Astrophysics Data System (ADS)

Quaranta, Vanessa; Hellström, Matti; Behler, Jörg; Kullgren, Jolla; Mitev, Pavlin D.; Hermansson, Kersti

2018-06-01

Unraveling the atomistic details of solid/liquid interfaces, e.g., by means of vibrational spectroscopy, is of vital importance in numerous applications, from electrochemistry to heterogeneous catalysis. Water-oxide interfaces represent a formidable challenge because a large variety of molecular and dissociated water species are present at the surface. Here, we present a comprehensive theoretical analysis of the anharmonic OH stretching vibrations at the water/ZnO(101 ¯ 0) interface as a prototypical case. Molecular dynamics simulations employing a reactive high-dimensional neural network potential based on density functional theory calculations have been used to sample the interfacial structures. In the second step, one-dimensional potential energy curves have been generated for a large number of configurations to solve the nuclear Schrödinger equation. We find that (i) the ZnO surface gives rise to OH frequency shifts up to a distance of about 4 Å from the surface; (ii) the spectrum contains a number of overlapping signals arising from different chemical species, with the frequencies decreasing in the order ν(adsorbed hydroxide) > ν(non-adsorbed water) > ν(surface hydroxide) > ν(adsorbed water); (iii) stretching frequencies are strongly influenced by the hydrogen bond pattern of these interfacial species. Finally, we have been able to identify substantial correlations between the stretching frequencies and hydrogen bond lengths for all species.

MESSENGER Searches for Less Abundant or Weakly Emitting Species in Mercury's Exosphere

NASA Technical Reports Server (NTRS)

Vervack, Ronald J., Jr.; McClintock, William E.; Killen, Rosemary M.; Sprague, Ann L.; Burger, Matthew H.; Merkel, Aimee W.; Sarantos, Menelaos

2011-01-01

Mercury's exosphere is composed of material that originates at the planet's surface, whether that material is native or delivered by the solar wind and micrometeoroids. Many exospheric species have been detected by remote sensing, including H and He by Mariner 10, Na, K, and Ca by ground-based observations, and H, Na, Ca, Mg, and Ca+ by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft. Other exospheric species, including Fe, AI, Si, 0, S, Mn, CI, Ti, OH, and their ions, are expected to be present on the basis of MESSENGER surface measurements and models of Mercury's surface chemistry. Here we report on searches for these species made with the Ultraviolet and Visible Spectrometer (UVVS) channel of the Mercury Atmospheric and Surface Composition Spectrometer (MASCS). No obvious signatures of the listed species have yet been observed in Mercury's exosphere by the UVVS as of this writing. It is possible that detections are elusive because the optimum regions of the exosphere have not been sampled. The Sun-avoidance constraints on MESSENGER place tight limits on instrument boresight directions, and some regions are probed infrequently. If there are strong spatial gradients in the distribution of weakly emitting species, a high-resolution sampling of specific regions may be required to detect them. Summing spectra over time will also aid in the ability to detect weaker emission. Observations to date nonetheless permit strong upper limits to be placed on the abundances of many undetected species, in some cases as functions of time and space. As those limits are lowered with time, the absence of detections can provide insight into surface composition and the potential source mechanisms of exospheric material.

Tree Resin Composition, Collection Behavior and Selective Filters Shape Chemical Profiles of Tropical Bees (Apidae: Meliponini)

PubMed Central

Leonhardt, Sara D.; Schmitt, Thomas; Blüthgen, Nico

2011-01-01

The diversity of species is striking, but can be far exceeded by the chemical diversity of compounds collected, produced or used by them. Here, we relate the specificity of plant-consumer interactions to chemical diversity applying a comparative network analysis to both levels. Chemical diversity was explored for interactions between tropical stingless bees and plant resins, which bees collect for nest construction and to deter predators and microbes. Resins also function as an environmental source for terpenes that serve as appeasement allomones and protection against predators when accumulated on the bees' body surfaces. To unravel the origin of the bees' complex chemical profiles, we investigated resin collection and the processing of resin-derived terpenes. We therefore analyzed chemical networks of tree resins, foraging networks of resin collecting bees, and their acquired chemical networks. We revealed that 113 terpenes in nests of six bee species and 83 on their body surfaces comprised a subset of the 1,117 compounds found in resins from seven tree species. Sesquiterpenes were the most variable class of terpenes. Albeit widely present in tree resins, they were only found on the body surface of some species, but entirely lacking in others. Moreover, whereas the nest profile of Tetragonula melanocephala contained sesquiterpenes, its surface profile did not. Stingless bees showed a generalized collecting behavior among resin sources, and only a hitherto undescribed species-specific “filtering” of resin-derived terpenes can explain the variation in chemical profiles of nests and body surfaces from different species. The tight relationship between bees and tree resins of a large variety of species elucidates why the bees' surfaces contain a much higher chemodiversity than other hymenopterans. PMID:21858119

Leaf micromorphology of some Phyllanthus L. species (Phyllanthaceae)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solihani, N. S., E-mail: noorsolihani@gmail.com; Noraini, T., E-mail: norainitalip@gmail.com; Azahana, A., E-mail: bell-azahana@yahoo.com

2015-09-25

Comparative leaf micromorphological study was conducted of five chosen Phyllanthus L. (Phyllanthaceae) species, namely P. acidus L., P. elegans Wall. ex Müll. Arg., P. emblica L., P. urinaria L. and P. pulcher Wall. ex Müll. Arg. The objective of this study is to identify the leaf micromorphological characteristics that can be used in species identification. The procedures involve examination under scanning electron microscope. Findings of this study have demonstrated variations in the leaf micromorphological characteristics such as in the types of waxes present on adaxial and abaxial epidermis surfaces, in the stomata and types of trichome. Common character present inmore » all species studied are the presence of a thin film layer and buttress-like waxes on epidermal leaf surfaces. Diagnostics characters found in this study are the presence of papilla in P. elegens, amphistomatic stomata in P. urinaria and flaky waxes in P. pulcher. The result of this study has shown that leaf micromorphological characters have some taxonomic significance and can be used in identification of species in the genus Phyllanthus.« less

Dielectrophoresis-based particle sensor using nanoelectrode arrays

NASA Technical Reports Server (NTRS)

Arumugam, Prabhu U. (Inventor); Li, Jun (Inventor); Cassell, Alan M. (Inventor)

2009-01-01

A method for concentrating or partly separating particles of a selected species from a liquid or fluid containing these particles and flowing in a channel, and for determining if the selected species particle is present in the liquid or fluid. A time varying electrical field E, having a root-mean-square intensity E.sup.2.sub.rms with a non-zero gradient in a direction transverse to the liquid or fluid flow direction, is produced by a nanostructure electrode array, with a very high magnitude gradient near exposed electrode tips. A dielectrophoresis force causes the selected particles to accumulate near the electrode tips, if the medium and selected particles have substantially different dielectric constants. An insulating material surrounds most of each of the nanostructure electrodes, and a region of the insulating material surface is functionalized to promote attachment of the selected species particles to the surface. An electrical property value Z(meas) is measured at the functionalized surface and is compared with a reference value Z(ref) to determine if the selected species particles are attached to the functionalized surface.

Surface Roughness of Various Diamond-Like Carbon Films

NASA Astrophysics Data System (ADS)

Liu, Dongping; Liu, Yanhong; Chen, Baoxiang

2006-11-01

Atomic force microscopy is used to estimate and compare the surface morphology of hydrogenated and hydrogen-free diamond-like carbon (DLC) films. The films were prepared by using DC magnetron sputtering of a graphite target, pulsed cathodic carbon arcs, electron cyclotron resonance (ECR), plasma source ion implantation and dielectric barrier discharge (DBD). The difference in the surface structure is presented for each method of deposition. The influences of various discharge parameters on the film surface properties are discussed based upon the experimental results. The coalescence process via the diffusion of adsorbed carbon species is responsible for the formation of hydrogen-free DLC films with rough surfaces. The films with surface roughness at an atomic level can be deposited by energetic ion impacts in a highly ionized carbon plasma. The dangling bonds created by atomic hydrogen lead to the uniform growth of hydrocarbon species at the a-C:H film surfaces of the ECR or DBD plasmas.

Surface hydrophobicity of slippery zones in the pitchers of two Nepenthes species and a hybrid

PubMed Central

Wang, Lixin; Zhou, Qiang

2016-01-01

To investigate the hydrophobicity of slippery zones, static contact angle measurement and microstructure observation of slippery surfaces from two Nepenthes species and a hybrid were conducted. Marginally different static contact angles were observed, as the smallest (133.83°) and greatest (143.63°) values were recorded for the N. alata and N. miranda respectively, and the median value (140.40°) was presented for the N. khasiana. The slippery zones under investigation exhibited rather similar surface morphologies, but different structural dimensions. These findings probably suggest that the geometrical dimensions of surface architecture exert primary effects on differences in the hydrophobicity of the slippery zone. Based on the Wenzel and Cassie-Baxter equations, models were proposed to analyze the manner in which geometrical dimensions affect the hydrophobicity of the slippery surfaces. The results of our analysis demonstrated that the different structural dimensions of lunate cells and wax platelets make the slippery zones present different real area of the rough surface and thereby generate somewhat distinguishable hydrophobicity. The results support a supplementary interpretation of surface hydrophobicity in plant leaves, and provide a theoretical foundation for developing bioinspired materials with hydrophobic properties and self-cleaning abilities. PMID:26813707

Modelling of Surfaces. Part 2: Metallic Alloy Surfaces Using the BFS Method

NASA Technical Reports Server (NTRS)

Bozzolo, Guillermo; Ferrante, John; Kobistek, Robert J.

1994-01-01

Using BFS, a new semiempirical method for alloys, we study the surface structure of fcc ordered binary alloys. We concentrate on the calculation of surface energies and surface relaxations for the L1(sub 0) and L1(sub 2) ordered structures. Different terminations of the low-index faces are studied. Also, we present results for the interlayer relaxations for planes close to the surface, revealing different relaxations for atoms of different species producing a rippled surface layer.

Integrated surface management for pipeline construction: The Mid-America Pipeline Company Four Corners Project

Treesearch

Maria L. Sonett

1999-01-01

Integrated surface management techniques for pipeline construction through arid and semi-arid rangeland ecosystems are presented in a case history of a 412-mile pipeline construction project in New Mexico. Planning, implementation and monitoring for restoration of surface hydrology, soil stabilization, soil cover, and plant species succession are discussed. Planning...

Monte Carlo kinetics simulations of ice-mantle formation on interstellar grains

NASA Astrophysics Data System (ADS)

Garrod, Robin

2015-08-01

The majority of interstellar dust-grain chemical kinetics models use rate equations, or alternative population-based simulation methods, to trace the time-dependent formation of grain-surface molecules and ice mantles. Such methods are efficient, but are incapable of considering explicitly the morphologies of the dust grains, the structure of the ices formed thereon, or the influence of local surface composition on the chemistry.A new Monte Carlo chemical kinetics model, MIMICK, is presented here, whose prototype results were published recently (Garrod 2013, ApJ, 778, 158). The model calculates the strengths and positions of the potential mimima on the surface, on the fly, according to the individual pair-wise (van der Waals) bonds between surface species, allowing the structure of the ice to build up naturally as surface diffusion and chemistry occur. The prototype model considered contributions to a surface particle's potential only from contiguous (or "bonded") neighbors; the full model considers contributions from surface constituents from short to long range. Simulations are conducted on a fully 3-D user-generated dust-grain with amorphous surface characteristics. The chemical network has also been extended from the simple water system previously published, and now includes 33 chemical species and 55 reactions. This allows the major interstellar ice components to be simulated, such as water, methane, ammonia and methanol, as well as a small selection of more complex molecules, including methyl formate (HCOOCH3).The new model results indicate that the porosity of interstellar ices are dependent on multiple variables, including gas density, the dust temperature, and the relative accretion rates of key gas-phase species. The results presented also have implications for the formation of complex organic molecules on dust-grain surfaces at very low temperatures.

A low Earth orbit molecular beam space simulation facility

NASA Technical Reports Server (NTRS)

Cross, J. B.

1984-01-01

A brief synopsis of the low Earth orbit (LEO) satellite environment is presented including neutral and ionic species. Two ground based atomic and molecular beam instruments are described which are capable of simulating the interaction of spacecraft surfaces with the LEO environment and detecting the results of these interactions. The first detects mass spectrometrically low level fluxes of reactively and nonreactively surface scattered species as a function of scattering angle and velocity while the second ultrahigh velocity (UHV) molecular beam, laser induced fluorescence apparatus is capable of measuring chemiluminescence produced by either gas phase or gas-surface interactions. A number of proposed experiments are described.

Selective Catalytic Reduction of NO by NH 3 with WO 3-TiO 2 Catalysts: Influence of Catalyst Synthesis Method

DOE PAGES

He, Yuanyuan; Ford, Michael E.; Zhu, Minghui; ...

2016-02-02

A series of supported WO 3/TiO 2 catalysts was prepared by a new synthesis procedure involving co-precipitation of an aqueous TiO(OH) 2 and (NH 4) 10W 12O 41*5H 2O slurry under controlled pH conditions. The morphological properties, molecular structures, surface acidity and surface chemistry of the supported WO 3/TiO 2 catalysts were determined with BET, in situ Raman, in situ IR and temperature-programmed surface reaction (TPSR) spectroscopy, respectively. Isotopic 18O- 16O exchange demonstrated that tungsten oxide was exclusively present as surface WO x species on the TiO 2 support with mono-oxo W=O coordination. In contrast to previous studies employing impregnationmore » synthesis that found only surface one mono-oxo O=WO 4 site on TiO 2, the co-precipitation procedure resulted in the formation of two distinct surface WO x species: mono-oxo O=WO 4 (~1010-1017 cm -1) on low defect density patches of TiO 2 and a second mono-oxo O=WO 4 (~983-986 cm -1) on high defect density patches of TiO 2. The concentration of the second WO x surface species increases as a function of solution pH. Both surface WOx sites, however, exhibited the same NO/NH 3 SCR reactivity. The co-precipitated WO 3-TiO 2 catalysts synthesized in alkaline solutions exhibited enhanced performance for the NO/NH 3 SCR reaction that is ascribed to the greater number of surface defects on the resulting TiO2 support. For the co-precipitated catalyst prepared at pH10, surface NH 4 + species on Br nsted acid sites were found to be more reactive than surface NH 3* species on Lewis acid sites for SCR of NO with NH 3.« less

Herbaceous plants as filters: immobilization of particulates along urban street corridors.

PubMed

Weber, Frauke; Kowarik, Ingo; Säumel, Ina

2014-03-01

Among air pollutants, particulate matter (PM) is considered to be the most serious threat to human health. Plants provide ecosystem services in urban areas, including reducing levels of PM by providing a surface for deposition and immobilization. While previous studies have mostly addressed woody species, we focus on herbaceous roadside vegetation and assess the role of species traits such as leaf surface roughness or hairiness for the immobilization of PM. We found that PM deposition patterns on plant surfaces reflect site-specific traffic densities and that strong differences in particulate deposition are present among species. The amount of immobilized PM differed according to particle type and size and was related to specific plant species traits. Our study suggests that herbaceous vegetation immobilizes a significant amount of the air pollutants relevant to human health and that increasing biodiversity of roadside vegetation supports air filtration and thus healthier conditions along street corridors. Copyright © 2013 Elsevier Ltd. All rights reserved.

Outgassing Measurements for Three Materials, Combined with Vacuum Ultraviolet Radiation Illumination of the Volatile Condensable Materials

NASA Technical Reports Server (NTRS)

Albyn, Keith

2005-01-01

The photolysis of three organic materials, by vacuum ultraviolet (VUV) radiation, has been quantified using 15-MHz temperature-controlled quartz microbalances (TQCM's). The rate at which molecular species, released from the individual samples, condensed on two TQCM s was measured for periods of up to 139.9-hours. The individual samples were heated in an effusion cell and the emitted molecular species collected on a pair of TQCM's which were maintained at -40 degrees Celsius. At several points during the deposition measurement, the deposition surface of one TQCM was illuminated by a 30 Watt deuterium lamp, and the loss of material from that surface was observed. V W illumination of the TQCM, concurrent with condensation, reduced the rate that material was lost from the deposition surface. These measurements present a contrasting picture of molecular deposition, in the presence of VUV, to that presented by other investigators who observed an enhanced rate of molecular deposition, when the deposition surface was illuminated by VUV.

Use of LEED, Auger emission spectroscopy and field ion microscopy in microstructural studies

NASA Technical Reports Server (NTRS)

Ferrante, J.; Buckley, D. H.; Pepper, S. V.; Brainard, W. A.

1972-01-01

Surface research tools such as LEED, Auger emission spectroscopy analysis, and field ion microscopy are discussed. Examples of their use in studying adhesion, friction, wear, and lubrication presented. These tools have provided considerable insight into the basic nature of solid surface interactions. The transfer of metals from one surface to another at the atomic level has been observed and studied with each of these devices. The field ion microscope has been used to study polymer-metal interactions and Auger analysis to study the mechanism of polymer adhesion to metals. LEED and Auger analysis have identified surface segregation of alloying elements and indicated the influence of these elements in metallic adhesion. LEED and Auger analysis have assisted in adsorption studies in determining the structural arrangement and quantity of adsorbed species present in making an understanding of the influence of these species on adhesion possible. These devices are assisting in the furtherance of understanding of the fundamental mechanism involved in the adhesion, friction, wear, and lubrication processes.

Spines vs. microspines: an overview of the sculpture exine in selected basal and derived Asteraceae with focus on Asteroideae.

PubMed

Tellería, María C

2017-11-01

This study presents a detailed examination of the echinate and microechinate sculpturing in relation to the size of pollen grains in 31 selected species of Asteraceae belonging to the subfamilies Barnadesioideae, Mutisioideae, Carduoideae and Asteroideae. The aims were to recognize sculpturing patterns, under LM and SEM, within large and small pollen of both basal and derived species and to explore the features that could have taxonomic value to apply in palynological disciplines. The detailed examination of the exine surface showed both the relevance and limits of sculptural patterns for taxonomy. Under LM, the microechinate sculpture gave little taxonomic information, whereas in the echinate sculpture, three exine types and two subtypes were recognized. Type I included microechinate exine, which is commonly present in large pollen grains of the basal lineages. Types II (subtypes IIa and IIb) and III included echinate and smaller pollen grains. In these types, spines were always regularly arranged and, were characterized by the length, shape, tip, perforations and distribution. Type IIa included more or less conical spines usually with a distended base, less than 4 µm in length, present in species of different tribes like Astereae, Eupatorieae, Helenieae, Gnaphalieae, Senecioideae and Heliantheae to a lesser extent. Type IIb includes slender spines with narrower bases, longer than 4 µm, present in species of Coreopsideae, Heliantheae, Tageteae and Eupatorieae to a lesser extent. Type III included spines with swollen base, blunt tip and perforations over their entire surface. This type was present in only one of the basal species-Carduus thoermeri-and in one species of the derived tribe Helenieae, Gaillardia megapotamica. Probably, this is due to evolutionary convergence.

Improving confidence in environmental DNA species detection.

PubMed

Jerde, Christopher L; Mahon, Andrew R

2015-05-01

Will we catch fish today? Our grandfathers' responses were usually something along the lines of, 'Probably. I've caught them here before'. One of the foundations of ecology is identifying which species are present, and where. This informs our understanding of species richness patterns, spread of invasive species, and loss of threatened and endangered species due to environmental change. However, our understanding is often lacking, particularly in aquatic environments where biodiversity remains hidden below the water's surface. The emerging field of metagenetic species surveillance is aiding our ability to rapidly determine which aquatic species are present, and where. In this issue of Molecular Ecology Resources, Ficetola et al. () provide a framework for metagenetic environmental DNA surveillance to foster the confidence of our grandfathers' fishing prowess by more rigorously evaluating the replication levels necessary to quantify detection errors and ultimately improving our confidence in aquatic species presence. © 2015 John Wiley & Sons Ltd.

Embryotoxic effects of crude oil in mallard ducks and chicks

USGS Publications Warehouse

Hoffman, David J.

1978-01-01

Recent studies in this laboratory have revealed that surface applications of microliter amounts of some crude and fuel oils that coat less than 10% of the egg surface reduce hatching considerably in different avian species. Applications of paraffin compounds that coat equal areas of the egg surface do not reduce hatching suggesting that toxicity is due to causes other than asphyxia. In the present study, 1–10 μl of South Louisiana crude oil, an API reference oil, were applied to the surface of fertile mallard (Anas platyrhynchos) and chicken (Gallus gallus) eggs. Early embryolethality was greater in mallard embryos than in chick embryos, but later embryolethality that coincided with the time of rapid outgrowth of the chorioallantoic membrane was more prevalent in chick embryos. The overall incidence of embryolethality was similar in both species. Retardation of growth as reflected by embryonic body weight, crown-rump length, beak length, and general appearance was more pronounced in chick than mallard embryos. Teratogenic defects were more frequent in chick embryos, and incomplete or abnormal ossification of the skull was the most common. External application of equivalent amounts of a mixture of paraffin compounds present in crude oil had virtually no embryotoxic effects in either species, suggesting that other components including aromatic hydrocarbons and organometallics may cause the embryotoxicity.

Electrosorption of a modified electrode in the vicinity of phase transition: A Monte Carlo study

NASA Astrophysics Data System (ADS)

Gavilán Arriazu, E. M.; Pinto, O. A.

2018-03-01

We present a Monte Carlo study for the electrosorption of an electroactive species on a modified electrode. The surface of the electrode is modified by the irreversible adsorption of a non-electroactive species which is able to block a percentage of the adsorption sites. This generates an electrode with variable connectivity sites. A second species, electroactive in this case, is adsorbed in surface vacancies and can interact repulsively with itself. In particular, we are interested in the analysis of the effect of the non-electroactive species near of critical regime, where the c(2 × 2) structure is formed. Lattice-gas models and Monte Carlo simulations in the Gran Canonical Ensemble are used. The analysis conducted is based on the study of voltammograms, order parameters, isotherms, configurational entropy per site, at several values of energies and coverage degrees of the non-electroactive species.

Biophysical Mechanistic Modelling Quantifies the Effects of Plant Traits on Fire Severity: Species, Not Surface Fuel Loads, Determine Flame Dimensions in Eucalypt Forests

PubMed Central

Bedward, Michael; Penman, Trent D.; Doherty, Michael D.; Weber, Rodney O.; Gill, A. Malcolm; Cary, Geoffrey J.

2016-01-01

The influence of plant traits on forest fire behaviour has evolutionary, ecological and management implications, but is poorly understood and frequently discounted. We use a process model to quantify that influence and provide validation in a diverse range of eucalypt forests burnt under varying conditions. Measured height of consumption was compared to heights predicted using a surface fuel fire behaviour model, then key aspects of our model were sequentially added to this with and without species-specific information. Our fully specified model had a mean absolute error 3.8 times smaller than the otherwise identical surface fuel model (p < 0.01), and correctly predicted the height of larger (≥1 m) flames 12 times more often (p < 0.001). We conclude that the primary endogenous drivers of fire severity are the species of plants present rather than the surface fuel load, and demonstrate the accuracy and versatility of the model for quantifying this. PMID:27529789

Biophysical Mechanistic Modelling Quantifies the Effects of Plant Traits on Fire Severity: Species, Not Surface Fuel Loads, Determine Flame Dimensions in Eucalypt Forests.

PubMed

Zylstra, Philip; Bradstock, Ross A; Bedward, Michael; Penman, Trent D; Doherty, Michael D; Weber, Rodney O; Gill, A Malcolm; Cary, Geoffrey J

2016-01-01

The influence of plant traits on forest fire behaviour has evolutionary, ecological and management implications, but is poorly understood and frequently discounted. We use a process model to quantify that influence and provide validation in a diverse range of eucalypt forests burnt under varying conditions. Measured height of consumption was compared to heights predicted using a surface fuel fire behaviour model, then key aspects of our model were sequentially added to this with and without species-specific information. Our fully specified model had a mean absolute error 3.8 times smaller than the otherwise identical surface fuel model (p < 0.01), and correctly predicted the height of larger (≥1 m) flames 12 times more often (p < 0.001). We conclude that the primary endogenous drivers of fire severity are the species of plants present rather than the surface fuel load, and demonstrate the accuracy and versatility of the model for quantifying this.

Fructose 1,6-Bisphosphate aldolase, a novel immunogenic surface protein on Listeria species

USDA-ARS?s Scientific Manuscript database

Listeria monocytogenes is a ubiquitous food-borne pathogen, and its presence in food or production facilities highlights the importance of surveillance. Increased understanding of the surface exposed antigens on Listeria would provide potential diagnostic and therapeutic targets. In the present work...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, R.L.; Wade, G.L.; Straw, R.A.

A descriptive study of the naturally invading and planted flora was conducted during 1984-1985 on a 14- and 21-year-old contour surface mine the 14.2 ha Log Mountain Demonstration Area (LMDA), in Bell County, Kentucky. Six habitats are designated from areas created from coal mining; the 1963 bench, 1970 bench, bench highwalls, mine outslopes, mine seeps, and coal haul-telephone microwave tower road. Twenty-four of 25 woody and herbaceous species (11 indigenous, 13 non-indigenous) have persisted from plantings by personnel of the Northeastern Forest Experiment Station, USDA Forest Service. We recommend 11 native and exotic woody and herbaceous species for planting onmore » coal surface-mined areas. An annotated list of vascular plants comprises 360 taxa (286 indigenous, 74 non-indigenous) in 224 genera from 82 families. Taxa consist of 1 Lycopodiophyta, 1 Equisetophyta, 8 Polypodiophyta, 7 Pinophyta, and 343 Magnoliophyta. The most species-rich families are the Asteraceae (64), Poaceae (39), Fabaceae (20), Cyperaceae (16), Rosaceae (13), and Lamiaceae (11). A total of 155 Bell County distribution records were documented. Three threatened Kentucky species (Gentiana decora, Liparis loeselii, Silene ovata) were present in refugial habitats created by surface mining. The high species richness has resulted from native and naturalized invading species from the environs, native and exotic planted species, and species from the remnant seed bank. Forest vegetation is a complex mosaic of natural and semi-natural plant communities on the unplanted and planted areas of LMDA.« less

The Lidnis Instrument: Atmosphere And Surface Studies

NASA Astrophysics Data System (ADS)

Leblanc, F.; Chassefiere, E.; Porteneuve, J.; Berthelier, J.-J.; Sarkissian, A.; Meftha, M.; Johnson, R. E.; Chaussidon, M.; Jambon, A.

LIDNIS is a surface instrument for rocky planetary bodies (in particular for Mercury, Mars, the Moon or asteroids) which simultaneously studies the chemical composi- tion of surface material, its gaseous environment and the nature and importance of the atmosphere/surface interaction. A multipurpose mass spectrometer (called NIS for Neutral and Ion spectrometer) placed at the surface of a planetary body would first of all give us information on the local atmosphere, its elementary and isotopic compo- sition and temporal variation. It will also give us the access to the precipitation from the interplanetary space and the products due to this precipitation. The association to NIS of a laser induced desorption (LID) system strong enough to desorb and volatilize the first few tens micro meters of the surface will allow the analysis of the different species present in this layer that is the atmospheric species (volatiles, refractories and products of the interior outgassing), the energetic implanted species along the history of this body (Solar Wind, Solar Energetic Particles and Cosmic Rays) and the inter- nal composition. In the same way as it is usually done in laboratories for the Moon samples, LIDNIS, through a progressive outgassing of the regolith or the rock at the surface, will measure these different groups of species. The purpose of this poster is to describe such an instrument and to show its capabilities with low mass and power to measure efficiently fundamental parameters for our understanding of the origin and evolution of planetary bodies in the solar system.

Effect of Acid and Alcohol Network Forces within Functionalized Multiwall Carbon Nanotubes Bundles on Adsorption of Copper (II) Species

EPA Science Inventory

Adsorption of metals on carbon nanotubes (CNTs) has important applications in sensors, membranes, and water treatment. The adsorptive capacity of multiwall CNTs for copper species in water depends on the type of functional group present on their surface. The alcohol (COOH) and ac...

Stephanospora michoacanensis (Stephanosporaceae, Agaricales), a novel sequestrate truffle from North America

Treesearch

Gonzalo Guevara-Guerrero; Ivone Baez-Alvarado; Victor M. Gomez-Reyes; Michael Castellano

2015-01-01

Stephanospora michoacanensis is presented as a new species from North America. This angiocarpic species is recognized by its yellowcream peridial surface color, and broadly ellipsoid to subglobose, spiny or crested, inamyloid spores with a distinct, complete or nearly complete corona at its base. Stephanospora michoacanensis is similar to S. caroticolor, but S....

Sequence analysis of a bitter taste receptor gene repertoires in different ruminant species

USDA-ARS?s Scientific Manuscript database

Bitter taste has been extensively studied in mammalian species and is associated with sensitivity to toxins and with food choices that avoid dangerous substances in the diet. At the molecular level, bitter compounds are sensed by bitter taste receptor proteins (T2R) present at the surface of taste r...

Surface Dielectric Barrier Discharge Jet for Skin Disinfection

NASA Astrophysics Data System (ADS)

Creyghton, Yves; Meijer, Rogier; Verweij, Paul; van der Zanden, Frank; Leenders, Paul

A consortium consisting of the research institute TNO, the medical ­university and hospital St Radboud and two industrial enterprises is working on a non-thermal plasma treatment method for hand disinfection. The group is seeking for cooperation, in particular in the field of validation methods and potential ­standardization for plasma based disinfection procedures. The present paper describes technical progress in plasma source development together with initial microbiological data. Particular properties of the sheet shaped plasma volume are the possibility of treating large irregular surfaces in a short period of time, effective plasma produced species transfer to the surface together with high controllability of the nature of plasma species by means of temperature conditioning.

Characterisation of a PdCl 2/SnCl 2 electroless plating catalyst system adsorbed on barium titanate-based electroactive ceramics

NASA Astrophysics Data System (ADS)

Meenan, B. J.; Brown, N. M. D.; Wilson, J. W.

1994-03-01

A PdCl 2/SnCl 2 metallisation catalyst system, of the type used to activate non-conducting surfaces for electroless metal deposition, has been characterised by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The substrate is a barium titanate (BaTiO 3)-based electroactive ceramic of the type used in the fabrication of multilayer ceramic capacitors (MLCC). The treatment of the substrate surface with the PdCl 2/SnCl 2 "sensitiser" solution leads to the adsorption of catalytically inactive compounds of palladium and tin. Subsequent treatment of this surface with an "accelerator" solution removes excess oxides, hydroxides and salts of tin thereby leaving the active catalyst species, Pd xSn y, on the surface. Such sites, on exposure to the appropriete electroless plating bath, are then responsible for the metal deposition. In this study, the chemical state and relative quantities of the various surface species present after each of the processing stages have been determined by XPS. The surface roughness of the substrate results in less of the tin compounds present thereon being removed on washing the catalysed surface in the accelerator solution than normally reported for such systems, thereby affecting the measured Pd: Sn ratio. SEM studies show that the accelerator solution treatment generates crystalline areas, which may be a result of coagulation of the Pd xSn y particles present, in the otherwise amorphous catalyst coating.

Computational analysis of electrokinetically driven flow mixing in microchannels with patterned blocks

NASA Astrophysics Data System (ADS)

Chang, C.-C.; Yang, R.-J.

2004-04-01

Electroosmotic flow in microchannels is restricted to low Reynolds number regimes characterized by extremely weak inertia forces and laminar flow. Consequently, the mixing of different species occurs primarily through diffusion, and hence cannot readily be achieved within a short mixing channel. The current study presents a numerical investigation of electrokinetically driven flow mixing in microchannels with various numbers of incorporated patterned rectangular blocks. Furthermore, a novel approach is introduced which patterns heterogeneous surfaces on the upper faces of these rectangular blocks in order to enhance species mixing. The simulation results confirm that the introduction of rectangular blocks within the mixing channel slightly enhances species mixing by constricting the bulk flow, hence creating a stronger diffusion effect. However, it is noted that a large number of blocks and hence a long mixing channel are required if a complete mixing of the species is to be obtained. The results also indicate that patterning heterogeneous upper surfaces on the rectangular blocks is an effective means of enhancing the species mixing. It is shown that increasing the magnitude of the heterogeneous surface zeta potential enables a reduction in the mixing channel length and an improved degree of mixing efficiency.

Platinum group metal-free electrocatalysts: Effects of synthesis on structure and performance in proton-exchange membrane fuel cell cathodes

NASA Astrophysics Data System (ADS)

Workman, Michael J.; Dzara, Michael; Ngo, Chilan; Pylypenko, Svitlana; Serov, Alexey; McKinney, Sam; Gordon, Jonathan; Atanassov, Plamen; Artyushkova, Kateryna

2017-04-01

Development of platinum group metal free catalysts for the oxygen reduction reaction (ORR) in proton exchange membrane fuel cells (PEMFCs) requires understanding of the interactions between surface chemistry and performance, both of which are strongly dependent on synthesis conditions. To elucidate these complex relationships, a set of Fe-N-C catalysts derived from the same set of precursor materials is fabricated by varying several key synthetic parameters under controlled conditions. The results of physicochemical characterization are presented and compared with the results of rotating disk electrode (RDE) analysis and fuel cell testing. We find that electrochemical performance is strongly correlated with three key properties related to catalyst composition: concentrations of 1) atomically dispersed Fe species, 2) species in which N is bound to Fe, and 3) surface oxides. Not only are these factors related to performance, these types of chemical species are shown to correlate with each other. This study provides evidence supporting the role of iron coordinated with nitrogen as an active species for the ORR, and offers synthetic pathways to increase the density of atomically dispersed iron species and surface oxides for optimum performance.

Spectators Control Selectivity in Surface Chemistry: Acrolein Partial Hydrogenation Over Pd

PubMed Central

2015-01-01

We present a mechanistic study on selective hydrogenation of acrolein over model Pd surfaces—both single crystal Pd(111) and Pd nanoparticles supported on a model oxide support. We show for the first time that selective hydrogenation of the C=O bond in acrolein to form an unsaturated alcohol is possible over Pd(111) with nearly 100% selectivity. However, this process requires a very distinct modification of the Pd(111) surface with an overlayer of oxopropyl spectator species that are formed from acrolein during the initial stages of reaction and turn the metal surface selective toward propenol formation. By applying pulsed multimolecular beam experiments and in situ infrared reflection–absorption spectroscopy, we identified the chemical nature of the spectator and the reactive surface intermediate (propenoxy species) and experimentally followed the simultaneous evolution of the reactive intermediate on the surface and formation of the product in the gas phase. PMID:26481220

Cell surface differences of Naegleria fowleri and Naegleria lovaniensis exposed with surface markers.

PubMed

González-Robles, Arturo; Castañón, Guadalupe; Cristóbal-Ramos, Ana Ruth; Hernández-Ramírez, Verónica Ivonne; Omaña-Molina, Maritza; Martínez-Palomo, Adolfo

2007-12-01

Differences in the distribution of diverse cell surface coat markers were found between Naegleria fowleri and Naegleria lovaniensis. The presence of carbohydrate-containing components in the cell coat of the two species was detected by selective staining with ruthenium red and alcian blue. Using both markers, N. fowleri presented a thicker deposit than N. lovaniensis. The existence of exposed mannose or glucose residues was revealed by discriminatory agglutination with the plant lectin Concanavalin A. These sugar residues were also visualized at the cell surface of these parasites either by transmission electron microscopy or by fluorescein-tagged Concanavalin A. Using this lectin cap formation was induced only in N. fowleri. The anionic sites on the cell surface detected by means of cationized ferritin were more apparent in N. fowleri. Biotinylation assays confirmed that even though the two amoebae species have some analogous plasma membrane proteins, there is a clear difference in their composition.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNesby, Kevin L.; Homan, Barrie E.; Benjamin, Richard A.

Here, the techniques presented in this paper allow for mapping of temperature, pressure, chemical species, and energy deposition during and following detonations of explosives, using high speed cameras as the main diagnostic tool. Additionally, this work provides measurement in the explosive near to far-field (0-500 charge diameters) of surface temperatures, peak air-shock pressures, some chemical species signatures, shock energy deposition, and air shock formation.

Impact of modified diamond-like carbon coatings on the spatial organization and disinfection of mixed-biofilms composed of Escherichia coli and Pantoea agglomerans industrial isolates.

PubMed

Gomes, L C; Deschamps, J; Briandet, R; Mergulhão, F J

2018-07-20

This work investigated the effects of diamond-like carbon (DLC) coatings on the architecture and biocide reactivity of dual-species biofilms mimicking food processing contaminants. Biofilms were grown using industrial isolates of Escherichia coli and Pantoea agglomerans on bare stainless steel (SST) and on two DLC surface coatings (a-C:H:Si:O designated by SICON® and a-C:H:Si designated by SICAN) in order to evaluate their antifouling activities. Quantification and spatial organization in single- and dual-species biofilms were examined by confocal laser scanning microscopy (CLSM) using a strain specific labelling procedure. Those assays revealed that the E. coli isolate exhibited a higher adhesion to the modified surfaces and a decreased susceptibility to disinfectant in presence of P. agglomerans than alone in axenic culture. While SICON® reduced the short-term growth of E. coli in axenic conditions, both DLC surfaces increased the E. coli colonization in presence of P. agglomerans. However, both modified surfaces triggered a significantly higher log reduction of E. coli cells within mixed-species biofilms, thus the use of SICON® and SICAN surfaces may be a good approach to facilitate the disinfection process in critical areas of food processing plants. This study presents a new illustration of the importance of interspecies interactions in surface-associated community functions, and of the need to evaluate the effectiveness of hygienic strategies with relevant multi-species consortia. Copyright © 2018 Elsevier B.V. All rights reserved.

Two new freshwater eutardigrade species from Sicily.

PubMed

Pilato, Giovanni; Sabella, Giorgio; Lisi, Oscar

2015-02-11

Two new species of freshwater Eutardigrada are described from Sicily: Isohypsibius rusticus sp. nov. and Isohypsibius zappalai sp. nov. The former species has eye spots, ornamented body surface with many, variously sized tubercles; bucco-pharyngeal apparatus of the Isohypsibius type; pharyngeal bulb with apophyses and two rod-shaped macroplacoids; microplacoid absent; claws, of the Isohypsibius type, well developed, with long and thin common basal portion; main branches of all claws without free accessory points; very thin lunules present; cuticular bars on the legs absent. Isohypsibius zappalai sp. nov. has eye spots; entire body surface with small tubercles rounded in shape, fairly uniformly sized and tending to form transverse lines; bucco-pharyngeal apparatus of the Isohypsibius type, pharyngeal bulb with apophyses and two macroplacoids; microplacoid absent; claws of the Isohypsibius type, well developed, with long common basal portion and both main and secondary branches with a wide proximal portion. Main branches of all claws with accessory points; small, flexible lunules present; cuticular bars on the legs absent.

In vitro apatite formation on nano-crystalline titania layer aligned parallel to Ti6Al4V alloy substrates with sub-millimeter gap.

PubMed

Hayakawa, Satoshi; Matsumoto, Yuko; Uetsuki, Keita; Shirosaki, Yuki; Osaka, Akiyoshi

2015-06-01

Pure titanium substrates were chemically oxidized with H2O2 and subsequent thermally oxidized at 400 °C in air to form anatase-type titania layer on their surface. The chemically and thermally oxidized titanium substrate (CHT) was aligned parallel to the counter specimen such as commercially pure titanium (cpTi), titanium alloy (Ti6Al4V) popularly used as implant materials or Al substrate with 0.3-mm gap. Then, they were soaked in Kokubo's simulated body fluid (SBF, pH 7.4, 36.5 °C) for 7 days. XRD and SEM analysis showed that the in vitro apatite-forming ability of the contact surface of the CHT specimen decreased in the order: cpTi > Ti6Al4V > Al. EDX and XPS surface analysis showed that aluminum species were present on the contact surface of the CHT specimen aligned parallel to the counter specimen such as Ti6Al4V and Al. This result indicated that Ti6Al4V or Al specimens released the aluminum species into the SBF under the spatial gap. The released aluminum species might be positively or negatively charged in the SBF and thus can interact with calcium or phosphate species as well as titania layer, causing the suppression of the primary heterogeneous nucleation and growth of apatite on the contact surface of the CHT specimen under the spatial gap. The diffusion and adsorption of aluminum species derived from the half-sized counter specimen under the spatial gap resulted in two dimensionally area-selective deposition of apatite particles on the contact surfaces of the CHT specimen.

Molecular carbon nitride ion beams for enhanced corrosion resistance of stainless steel

NASA Astrophysics Data System (ADS)

Markwitz, A.; Kennedy, J.

2017-10-01

A novel approach is presented for molecular carbon nitride beams to coat stainless surfaces steel using conventional safe feeder gases and electrically conductive sputter targets for surface engineering with ion implantation technology. GNS Science's Penning type ion sources take advantage of the breaking up of ion species in the plasma to assemble novel combinations of ion species. To test this phenomenon for carbon nitride, mixtures of gases and sputter targets were used to probe for CN+ ions for simultaneous implantation into stainless steel. Results from mass analysed ion beams show that CN+ and a variety of other ion species such as CNH+ can be produced successfully. Preliminary measurements show that the corrosion resistance of stainless steel surfaces increased sharply when implanting CN+ at 30 keV compared to reference samples, which is interesting from an application point of view in which improved corrosion resistance, surface engineering and short processing time of stainless steel is required. The results are also interesting for novel research in carbon-based mesoporous materials for energy storage applications and as electrode materials for electrochemical capacitors, because of their high surface area, electrical conductivity, chemical stability and low cost.

CHO-bearing organic compounds at the surface of 67P/Churyumov-Gerasimenko revealed by Ptolemy

NASA Astrophysics Data System (ADS)

Wright, I. P.; Sheridan, S.; Barber, S. J.; Morgan, G. H.; Andrews, D. J.; Morse, A. D.

2015-07-01

The surface and subsurface of comets preserve material from the formation of the solar system. The properties of cometary material thus provide insight into the physical and chemical conditions during their formation. We present mass spectra taken by the Ptolemy instrument 20 minutes after the initial touchdown of the Philae lander on the surface of comet 67P/Churyumov-Gerasimenko. Regular mass distributions indicate the presence of a sequence of compounds with additional -CH2- and -O- groups (mass/charge ratios 14 and 16, respectively). Similarities with the detected coma species of comet Halley suggest the presence of a radiation-induced polymer at the surface. Ptolemy measurements also indicate an apparent absence of aromatic compounds such as benzene, a lack of sulfur-bearing species, and very low concentrations of nitrogenous material.

Nitrile versus isonitrile adsorption at interstellar grains surfaces. I. Hydroxylated surfaces

NASA Astrophysics Data System (ADS)

Bertin, M.; Doronin, M.; Fillion, J.-H.; Michaut, X.; Philippe, L.; Lattelais, M.; Markovits, A.; Pauzat, F.; Ellinger, Y.; Guillemin, J.-C.

2017-02-01

Context. Almost 20% of the 200 different species detected in the interstellar and circumstellar media present a carbon atom linked to nitrogen by a triple bond. Among these 37 molecules, 30 are nitrile R-CN compounds, the remaining seven belonging to the isonitrile R-NC family. How these species behave in presence of the grain surfaces is still an open question. Aims: In this contribution we investigate whether the difference between nitrile and isonitrile functional groups may induce differences in the adsorption energies of the related isomers at the surfaces of interstellar grains of different nature and morphologies. Methods: The question was addressed by means of a concerted experimental and theoretical study of the adsorption energies of CH3CN and CH3NC on the surface water ice and silica. The experimental determination of the molecule - surface interaction energies was carried out using temperature programmed desorption (TPD) under an ultra-high vacuum (UHV) between 70 and 160 K. Theoretically, the question was addressed using first principle periodic density functional theory (DFT) to represent the organized solid support. Results: The most stable isomer (CH3CN) interacts more efficiently with the solid support than the higher energy isomer (CH3NC) for water ice and silica. Comparing with the HCN and HNC pair of isomers, the simulations show an opposite behaviour, in which isonitrile HNC are more strongly adsorbed than nitrile HCN provided that hydrogen bonds are compatible with the nature of the model surface. Conclusions: The present study confirms that the strength of the molecule surface interaction between isomers is not related to their intrinsic stability but instead to their respective ability to generate different types of hydrogen bonds. Coupling TPD to first principle simulations is a powerful method for investigating the possible role of interstellar surfaces in the release of organic species from grains, depending on the environment.

Faunal composition and organic surface encrustations at hydrothermal vents on the southern Juan De Fuca Ridge

NASA Astrophysics Data System (ADS)

Tunnicliffe, Verena; Fontaine, A. R.

1987-10-01

Examination of a small collection of macroinvertebrates from three vents of the southern Juan de Fuca vent field reveals differences between the vents with respect to species composition, species habits, and microbial and metallic deposits on their surfaces. TWo apparently new vestimentiferan species were found, and for the first time the Juan de Fuca palm worm was observed to dwell on smokers. High acidity values recorded in this system may interfere with the process of shell calcification in an archaeogastropod snail. The surfaces of vestimentifer an tubes at two vents are heavily encrusted with microbial and metallic accumulations. Scanning electron microscope, transmission electron microscope, and energy dispersive X ray microanalysis observations show that iron-based crusts on orange tubes are built from accumulations of an Fe-rich particle of distinctive size and shape. Morphological evidence is presented for the microbial origin of Fe-rich particles. Zn-rich particles found on black tubes are not of microbial origin. We suggest that iron deposition on surfaces in the vent environment is initially biocatalytic but subsequent deposits may build by simple inorganic reactions.

Spores of Mucor ramosissimus, Mucor plumbeus and Mucor circinelloides and their ability to activate human complement system in vitro.

PubMed

Granja, Luiz Fernando Zmetek; Pinto, Lysianne; Almeida, Cátia Amancio; Alviano, Daniela Sales; Da Silva, Maria Helena; Ejzemberg, Regina; Alviano, Celuta Sales

2010-03-01

Complement activation by spores of Mucor ramosissimus, Mucor plumbeus and Mucor circinelloides was studied using absorbed human serum in the presence or absence of chelators (EGTA or EDTA). We found that the spore caused full complement activation when incubated with EGTA-Mg2+ or without chelators, indicating that the alternative pathway is mainly responsible for this response. In order to compare activation profiles from each species, ELISAs for C3 and C4 fragments, mannan binding lectin (MBL), C-reactive protein (CRP) and IgG studies were carried out. All proteins were present on the species tested. Immunofluorescence tests demonstrated the presence of C3 fragments on the surface of all samples, which were confluent throughout fungal surfaces. The same profile of C3, C4, MBL, CRP and IgG deposition, observed in all species, suggests a similar activation behavior for these species.

Physical State of Ices in the Outer Solar System. Revised

NASA Technical Reports Server (NTRS)

Roush, Ted L.; DeVincenzi, Donald (Technical Monitor)

2001-01-01

Comparison of the identity and abundances of ices observed around protostars and those associated with comets clearly suggests that comets preserve the heritage of the interstellar materials that aggregated to form them. However, the ability to identify these same species on icy satellites in the outer solar system is a complex function of the composition of the original ices, their subsequent thermal histories, and their exposure to various radiation environments. Our ability to identify the ices currently present on objects in the outer solar system relies upon observational and laboratory, and theoretical efforts. To date there is ample observational evidence for crystalline water ice throughout the outer solar system. In addition, there is growing evidence that amorphous ice may be present on some bodies. More volatile ices, e.g. N2, CH4. CO, and other species, e.g. ammonia hydrate, are identified on objects lying at and beyond Uranus. Both photolysis and radiolysis play important roles in altering the original surfaces due to chemical reactions and erosion of the surface. Ultraviolet photolysis appears to dominate alteration of the upper few hundred Angstroms, although sputtering the surface can sometimes be a significantly competitative process; dominating on icy surfaces embedded in a strong planetary magnetospheric field. There is growing observational evidence that the by-products of photolysis and radiolysis, suggested on a theoretical basis, are present on icy surfaces.

Observations of Mercury's Surface-Bounded Exosphere from Orbit: Results from the Mercury Atmospheric and Surface Composition Spectrometer aboard the MESSENGER Spacecraft

NASA Astrophysics Data System (ADS)

McClintock, W. E.; Burger, M. H.; Cassidy, T. A.; Killen, R. M.; Merkel, A. W.; Sarantos, M.; Solomon, S. C.; Vervack, R. J., Jr.

2015-12-01

The Mercury Atmospheric and Surface Composition Spectrometer (MASCS), on the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft, conducted orbital observations of Mercury's dayside and nightside exosphere from 29 March 2011 to the end of the mission on 30 April 2015. Over slightly more than four Earth-years, MASCS measured emission profiles versus altitude for calcium (Ca), sodium (Na), and magnesium (Mg) at a daily cadence. These species exhibit different spatial distributions, suggesting distinct source processes. MASCS observed seasonal variations in all three species that are remarkably repeatable from one Mercury year to the next, and did so consistently during the entire 17-Mercury-year duration of the orbital phase of the mission. Whereas MASCS has characterized the seasonal variation, it has provided, at best, only weak evidence for the episodic behavior observed in ground-based studies of Na. Joint analyses of MASCS observations and surface precipitation patterns for energetic particles inferred from observations by the Energetic Particle Spectrometer (EPS) and the Fast Imaging Plasma Spectrometer (FIPS) on MESSENGER have not yielded clear correlations. This lack of correlation may be due in part to the MASCS observational geometries. MASCS has conducted a number of searches for other, weakly emitting species. Hydrogen data from the orbital phase are consistent with profiles observed during MESSENGER's flybys of Mercury. Oxygen detections have proven elusive, and the previously reported observation with a brightness of 4 R may only be an upper limit. Ongoing analysis of weak species data suggests that additional species are present.

Influence of cuticle nanostructuring on the wetting behaviour/states on cicada wings.

PubMed

Sun, Mingxia; Liang, Aiping; Watson, Gregory S; Watson, Jolanta A; Zheng, Yongmei; Ju, Jie; Jiang, Lei

2012-01-01

The nanoscale protrusions of different morphologies on wing surfaces of four cicada species were examined under an environmental scanning electron microscope (ESEM). The water contact angles (CAs) of the wing surfaces were measured along with droplet adhesion values using a high-sensitivity microelectromechanical balance system. The water CA and adhesive force measurements obtained were found to relate to the nanostructuring differences of the four species. The adhesive forces in combination with the Cassie-Baxter and Wenzel approximations were used to predict wetting states of the insect wing cuticles. The more disordered and inhomogeneous surface of the species Leptopsalta bifuscata demonstrated a Wenzel type wetting state or an intermediate state of spreading and imbibition with a CA of 81.3° and high adhesive force of 149.5 µN. Three other species (Cryptotympana atrata, Meimuna opalifer and Aola bindusara) exhibited nanostructuring of the form of conically shaped protrusions, which were spherically capped. These surfaces presented a range of high adhesional values; however, the CAs were highly hydrophobic (C. atrata and A. bindusara) and in some cases close to superhydrophobic (M. opalifer). The wetting states of A. bindusara, C. atrata and M. opalifer (based on adhesion and CAs) are most likely represented by the transitional region between the Cassie-Baxter and Wenzel approximations to varying degrees.

Time- and angle-resolved photoemission spectroscopy of hydrated electrons near a liquid water surface.

PubMed

Yamamoto, Yo-ichi; Suzuki, Yoshi-Ichi; Tomasello, Gaia; Horio, Takuya; Karashima, Shutaro; Mitríc, Roland; Suzuki, Toshinori

2014-05-09

We present time- and angle-resolved photoemission spectroscopy of trapped electrons near liquid surfaces. Photoemission from the ground state of a hydrated electron at 260 nm is found to be isotropic, while anisotropic photoemission is observed for the excited states of 1,4-diazabicyclo[2,2,2]octane and I- in aqueous solutions. Our results indicate that surface and subsurface species create hydrated electrons in the bulk side. No signature of a surface-bound electron has been observed.

General Model for Multicomponent Ablation Thermochemistry

NASA Technical Reports Server (NTRS)

Milos, Frank S.; Marschall, Jochen; Rasky, Daniel J. (Technical Monitor)

1994-01-01

A previous paper (AIAA 94-2042) presented equations and numerical procedures for modeling the thermochemical ablation and pyrolysis of thermal protection materials which contain multiple surface species. This work describes modifications and enhancements to the Multicomponent Ablation Thermochemistry (MAT) theory and code for application to the general case which includes surface area constraints, rate limited surface reactions, and non-thermochemical mass loss (failure). Detailed results and comparisons with data are presented for the Shuttle Orbiter reinforced carbon-carbon oxidation protection system which contains a mixture of sodium silicate (Na2SiO3), silica (SiO2), silicon carbide (SiC), and carbon (C).

Morphological comparison of Astropecten cingulatus and a new species of Astropecten (Paxillosida, Astropectinidae) from the Gulf of Mexico.

PubMed

Lawrence, John M; Cobb, Janessa C; Herrera, Joan C; DurÁn-gonzÁlez, Alicia; SolÍs-marÍn, Francisco Alonso

2018-04-09

Astropecten cingulatus is a conspicuous species, which displays a large superomarginal plate series on the abactinal surface. Herein we describe a new species from off the Texas coast that shows the superficial appearance of A. cingulatus, including these large superomarginal plates, but with armature differing from that of typological A. cingulatus. This species shows the actinal surface of the inferomarginal plates without the squamules present on A. cingulatus. In addition, the adambulacral plates possessed but a single central large spine surrounded by a circle of spines rather than spine rows. The abactinal paxillar region was also very narrow. Statistical analysis of these and other morphological characters showed the specimens differed significantly from those of A. cingulatus. The regression of the slope of R:SM# vs. R was significant but the intercept was not. Therefore the two species are indistinguishable at small sizes based on R:SM. Compared to known Atlantic Astropecten spp. these observed characters warrant the description of a new species, Astropecten karankawai, for the specimens from off the coasts of Texas and Mexico.

Aureobasidium melanogenum: a native of dark biofinishes on oil treated wood.

PubMed

van Nieuwenhuijzen, Elke J; Houbraken, Jos A M P; Meijer, Martin; Adan, Olaf C G; Samson, Robert A

2016-05-01

The genus Aureobasidium, which is known as a wood staining mould, has been detected on oil treated woods in the specific stain formation called biofinish. This biofinish is used to develop a new protective, self-healing and decorative biotreatment for wood. In order to understand and control biofinish formation on oil treated wood, the occurrence of different Aureobasidium species on various wood surfaces was studied. Phenotypic variability within Aureobasidium strains presented limitations of morphological identification of Aureobasidium species. PCR amplification and Sanger sequencing of ITS and RPB2 were used to identify the culturable Aureobasidium species composition in mould stained wood surfaces with and without a biofinish. The analysed isolates showed that several Aureobasidium species were present and that Aureobasidium melanogenum was predominantly detected, regardless of the presence of a biofinish and the type of substrate. A. melanogenum was detected on wood samples exposed in the Netherlands, Cameroon, South Africa, Australia and Norway. ITS-specific PCR amplification, cloning and sequencing of DNA extracted from biofinish samples confirmed results of the culturing based method: A. melanogenum is predominant within the Aureobasidium population of biofinishes on pine sapwood treated with raw linseed oil and the outdoor placement in the Netherlands.

A new species of the genus Scutiger (Anura: Megophryidae) from Medog of southeastern Tibet, China

PubMed Central

JIANG, Ke; WANG, Kai; ZOU, Da-Hu; YAN, Fang; LI, Pi-Peng; CHE, Jing

2016-01-01

A new species of Scutiger Theobald, 1868 is described from Medog, southeastern Tibet, China, based on morphological and molecular data. The new species was previously identified as Scutiger nyingchiensis, but it can be differentiated from the latter and all other congeners by the following combination of characters: (1) medium adult body size, SVL 50.5-55.6 mm in males and 53.8-57.2 mm in females; (2) maxillary teeth absent; (3) web rudimentary between toes; (4) prominent, conical-shaped tubercles on dorsal and lateral surfaces of body and limbs; (5) tubercles covered by black spines in both sexes in breeding condition; (6) a pair of pectoral glands and a pair of axillary glands present and covered by black spines in males in breeding condition, width of axillary gland less than 50% of pectoral gland; (7) nuptial spines present on dorsal surface of first and second fingers, and inner side of third finger in males in breeding condition; (8) spines absent on the abdominal region; (9) vocal sac absent. In addition, the distribution and conservation status of the new species are also discussed. PMID:26828031

Suckers and other bursal structures of Pomphorhynchus bulbocolli and Acanthocephalus dirus (Acanthocephala).

PubMed

Doyle, L R; Gleason, L N

1991-06-01

Accessory copulatory structures in the bursa of Pomphorhynchus bulbocolli include 2 suckers on the inner surface and bursal rays. A stylet was present in the penis of this species. Two suckers were present in the bursa of Acanthocephalus dirus, but bursal rays and a stylet in the penis were not observed. This is the first report of suckers present in the bursas of acanthocephalans. Copulatory cement caps and holes surrounded by a ring approximating the inner bursal diameter and not covered by a cap were present on the sides of some P. bulbocolli, indicating the possibility of hypodermic insemination in this species.

Surface degradation of uranium tetrafluoride

DOE PAGES

Tobin, J. G.; Duffin, A. M.; Yu, S. -W.; ...

2017-05-01

A detailed analysis of a single crystal of uranium tetrafluoride has been carried out. The techniques include x-ray absorption spectroscopy, as well as x-ray photoelectron spectroscopy and x-ray emission spectroscopy. Evidence will be presented for the presence of a uranyl species, possibly UO 2F 2, as a product of, or participant in the surface degradation.

The Three Sources of Gas in the Comae of Comets

NASA Technical Reports Server (NTRS)

Huebner, W. F.

1995-01-01

Surface water ice on a comet nucleus is the major source of coma gas. Dust, entrained by coma gas, fragments and vaporizes, forming a second, distributed source of coma gas constituents. Ice species more volatile than water ice below the surface of the nucleus are a third source of coma gas. Vapors from these ices, produced by heat penetrating into the nucleus, diffuse through pores outward into the coma. The second and third sources provide minor, but sometimes easily detectible, gaseous species in the coma. We present mixing ratios of observed minor coma constituents relative to water vapor as a function of heliocentric and cometocentric distances and compare these ratios with model predictions, assuming the sources of the minor species are either coma dust or volatile ices in the nucleus.

Fructose 1,6-Bisphosphate Aldolase, a Novel Immunogenic Surface Protein on Listeria Species

PubMed Central

Conceição, Fabricio Rochedo; Hust, Michael; Mendonça, Karla Sequeira; Moreira, Ângela Nunes; França, Rodrigo Correa; da Silva, Wladimir Padilha; Aleixo, José Antonio G.

2016-01-01

Listeria monocytogenes is a ubiquitous food-borne pathogen, and its presence in food or production facilities highlights the importance of surveillance. Increased understanding of the surface exposed antigens on Listeria would provide potential diagnostic and therapeutic targets. In the present work, using mass spectrometry and genetic cloning, we show that fructose-1,6-bisphosphate aldolase (FBA) class II in Listeria species is the antigen target of the previously described mAb-3F8. Western and dot blot assays confirmed that the mAb-3F8 could distinguish all tested Listeria species from close-related bacteria. Localization studies indicated that FBA is present in every fraction of Listeria cells, including supernatant and the cell wall, setting Listeria spp. as one of the few bacteria described to have this protein on their cell surface. Epitope mapping using ORFeome display and a peptide membrane revealed a 14-amino acid peptide as the potential mAb-3F8 epitope. The target epitope in FBA allowed distinguishing Listeria spp. from closely-related bacteria, and was identified as part of the active site in the dimeric enzyme. However, its function in cell surface seems not to be host cell adhesion-related. Western and dot blot assays further demonstrated that mAb-3F8 together with anti-InlA mAb-2D12 could differentiate pathogenic from non-pathogenic Listeria isolated from artificially contaminated cheese. In summary, we report FBA as a novel immunogenic surface target useful for the detection of Listeria genus. PMID:27489951

Fructose 1,6-Bisphosphate Aldolase, a Novel Immunogenic Surface Protein on Listeria Species.

PubMed

Mendonça, Marcelo; Moreira, Gustavo Marçal Schmidt Garcia; Conceição, Fabricio Rochedo; Hust, Michael; Mendonça, Karla Sequeira; Moreira, Ângela Nunes; França, Rodrigo Correa; da Silva, Wladimir Padilha; Bhunia, Arun K; Aleixo, José Antonio G

2016-01-01

Listeria monocytogenes is a ubiquitous food-borne pathogen, and its presence in food or production facilities highlights the importance of surveillance. Increased understanding of the surface exposed antigens on Listeria would provide potential diagnostic and therapeutic targets. In the present work, using mass spectrometry and genetic cloning, we show that fructose-1,6-bisphosphate aldolase (FBA) class II in Listeria species is the antigen target of the previously described mAb-3F8. Western and dot blot assays confirmed that the mAb-3F8 could distinguish all tested Listeria species from close-related bacteria. Localization studies indicated that FBA is present in every fraction of Listeria cells, including supernatant and the cell wall, setting Listeria spp. as one of the few bacteria described to have this protein on their cell surface. Epitope mapping using ORFeome display and a peptide membrane revealed a 14-amino acid peptide as the potential mAb-3F8 epitope. The target epitope in FBA allowed distinguishing Listeria spp. from closely-related bacteria, and was identified as part of the active site in the dimeric enzyme. However, its function in cell surface seems not to be host cell adhesion-related. Western and dot blot assays further demonstrated that mAb-3F8 together with anti-InlA mAb-2D12 could differentiate pathogenic from non-pathogenic Listeria isolated from artificially contaminated cheese. In summary, we report FBA as a novel immunogenic surface target useful for the detection of Listeria genus.

Coccolithophore assemblage response to Black Sea Water inflow into the North Aegean Sea (NE Mediterranean)

NASA Astrophysics Data System (ADS)

Karatsolis, B.-Th.; Triantaphyllou, M. V.; Dimiza, M. D.; Malinverno, E.; Lagaria, A.; Mara, P.; Archontikis, O.; Psarra, S.

2017-10-01

This study aims to presents the species composition of living coccolithophore communities in the NE Aegean Sea, investigating their spatial and temporal variations along a north-south transect in the area receiving the inflowing surface Black Sea Water (BSW) over the deeper Levantine Water (LW) layer. Coccolithophores in the area were relatively diverse and a total of 95 species over 3 sampling periods studied were recognized using Scanning Electron Microscope (SEM) techniques. R-mode hierarchical cluster analysis distinguished two coccolithophore Groups (I, IIa, IIb, IIc) with different ecological preferences. Emiliania huxleyi was the most abundant species of Group I, whereas Syracosphaera spp., Rhabdosphaera spp. and holococcolithophores were prevailing in the highly diversified Group II assemblages. Biometric analysis conducted on E. huxleyi coccoliths from Aegean water column and Black Sea sediment trap samples, indicated that during autumn, NE Aegean specimens in samples under BSW influence were featured by unimodal distribution concerning the coccolith relative tube width, with values similar to those provided by the Black Sea specimens. In early spring, coccoliths in the stations with increased BSW influx displayed a bimodal pattern of relative tube width with smaller values found mostly in the surface layers, while the distribution became again unimodal and dominated by larger values within the deeper LW layers. In the summer period, the typical LW holococcolithophore species (Group II) presented low cell numbers in the surface layer (<20 m), which is their usual ecological niche in the Aegean Sea, compared to greater depths, therefore marking LW mass flowing beneath the less saline BSW surface lid. In contrast to Black Sea early summer bloom conditions, E. huxleyi was almost absent in the NE Aegean during the summer sampling period.

A fully coupled 3D transport model in SPH for multi-species reaction-diffusion systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adami, Stefan; Hu, X. Y.; Adams, N. A.

2011-08-23

Abstract—In this paper we present a fully generalized transport model for multiple species in complex two and threedimensional geometries. Based on previous work [1] we have extended our interfacial reaction-diffusion model to handle arbitrary numbers of species allowing for coupled reaction models. Each species is tracked independently and we consider different physics of a species with respect to the bulk phases in contact. We use our SPH model to simulate the reaction-diffusion problem on a pore-scale level of a solid oxide fuel cell (SOFC) with special emphasize on the effect of surface diffusion.

Surface diffusion effects on growth of nanowires by chemical beam epitaxy

NASA Astrophysics Data System (ADS)

Persson, A. I.; Fröberg, L. E.; Jeppesen, S.; Björk, M. T.; Samuelson, L.

2007-02-01

Surface processes play a large role in the growth of semiconductor nanowires by chemical beam epitaxy. In particular, for III-V nanowires the surface diffusion of group-III species is important to understand in order to control the nanowire growth. In this paper, we have grown InAs-based nanowires positioned by electron beam lithography and have investigated the dependence of the diffusion of In species on temperature, group-III and -V source pressure and group-V source combinations by measuring nanowire growth rate for different nanowire spacings. We present a model which relates the nanowire growth rate to the migration length of In species. The model is fitted to the experimental data for different growth conditions, using the migration length as fitting parameter. The results show that the migration length increases with decreasing temperature and increasing group-V/group-III source pressure ratio. This will most often lead to an increase in growth rate, but deviations will occur due to incomplete decomposition and changes in sticking coefficient for group-III species. The results also show that the introduction of phosphorous precursor for growth of InAs1-xPx nanowires decreases the migration length of the In species followed by a decrease in nanowire growth rate.

Biominerals and waxes of Calamagrostis epigejos and Phragmites australis leaves from post-industrial habitats.

PubMed

Talik, Ewa; Guzik, Adam; Małkowski, Eugeniusz; Woźniak, Gabriela; Sierka, Edyta

2018-05-01

Vascular plants are able to conduct biomineralization processes and collect synthesized compounds in their internal tissues or to deposit them on their epidermal surfaces. This mechanism protects the plant from fluctuations of nutrient levels caused by different levels of supply and demand for them. The biominerals reflect both the metabolic characteristics of a vascular plant species and the environmental conditions of the plant habitat. The SEM/EDX method was used to examine the surface and cross-sections of the Calamagrostis epigejos and Phragmites australis leaves from post-industrial habitats (coal and zinc spoil heaps). The results from this study have showed the presence of mineral objects on the surfaces of leaves of both grass species. The calcium oxalate crystals, amorphous calcium carbonate spheres, and different silica forms were also found in the inner tissues. The high variety of mineral forms in the individual plants of both species was shown. The waxes observed on the leaves of the studied plants might be the initializing factor for the crystalline forms and structures that are present. For the first time, wide range of crystal forms is presented for C. epigejos. The leaf samples of P. australis from the post-industrial areas showed an increased amount of mineral forms with the presence of sulfur.

Feedbacks between geomorphology and biota controlling Earth surface processes and landforms: A review of foundation concepts and current understandings

NASA Astrophysics Data System (ADS)

Corenblit, Dov; Baas, Andreas C. W.; Bornette, Gudrun; Darrozes, José; Delmotte, Sébastien; Francis, Robert A.; Gurnell, Angela M.; Julien, Frédéric; Naiman, Robert J.; Steiger, Johannes

2011-06-01

This review article presents recent advances in the field of biogeomorphology related to the reciprocal coupling between Earth surface processes and landforms, and ecological and evolutionary processes. The aim is to present to the Earth Science community ecological and evolutionary concepts and associated recent conceptual developments for linking geomorphology and biota. The novelty of the proposed perspective is that (1) in the presence of geomorphologic-engineer species, which modify sediment and landform dynamics, natural selection operating at the scale of organisms may have consequences for the physical components of ecosystems, and particularly Earth surface processes and landforms; and (2) in return, these modifications of geomorphologic processes and landforms often feed back to the ecological characteristics of the ecosystem (structure and function) and thus to biological characteristics of engineer species and/or other species (adaptation and speciation). The main foundation concepts from ecology and evolutionary biology which have led only recently to an improved conception of landform dynamics in geomorphology are reviewed and discussed. The biogeomorphologic macroevolutionary insights proposed explicitly integrate geomorphologic niche-dimensions and processes within an ecosystem framework and reflect current theories of eco-evolutionary and ecological processes. Collectively, these lead to the definition of an integrated model describing the overall functioning of biogeomorphologic systems over ecological and evolutionary timescales.

A new technique for Auger analysis of surface species subject to electron-induced desorption.

NASA Technical Reports Server (NTRS)

Pepper, S. V.

1973-01-01

A method is presented to observe surface species subject to electron-induced desorption by Auger electron spectroscopy. The surface to be examined is moved under the electron beam at constant velocity, establishing a time-independent condition and eliminating the time response of the electron spectrometer as a limiting factor. The dependence of the Auger signal on the sample velocity, incident electron current, beam diameter, and desorption cross section is analyzed. It is shown that it is advantageous to analyze the moving sample with a high beam current, in contrast to the usual practice of using a low beam current to minimize desorption from a stationary sample. The method is illustrated by the analysis of a friction transfer film of PTFE, in which the fluorine is removed by electron-induced desorption. The method is relevant to surface studies in the field of lubrication and catalysis.

Carbon speciation and surface tension of fog

USGS Publications Warehouse

Capel, P.D.; Gunde, R.; Zurcher, F.; Giger, W.

1990-01-01

The speciation of carbon (dissolved/particulate, organic/inorganic) and surface tension of a number of radiation fogs from the urban area of Zurich, Switzerland, were measured. The carbon species were dominated by "dissolved" organic carbon (DOC; i.e., the fraction that passes through a filter), which was typically present at levels of 40-200 mg/L. Less than 10% of the DOC was identified as specific individual organic compounds. Particulate organic carbon (POC) accounted for 26-41% of the mass of the particles, but usually less than 10% of the total organic carbon mass. Inorganic carbon species were relatively minor. The surface tensions of all the measured samples were less than pure water and were correlated with their DOC concentrations. The combination of high DOC and POC and low surface tension suggests a mechanism for the concentration of hydrophobic organic contaminants in the fog droplet, which have been observed by numerous investigators. ?? 1990 American Chemical Society.

A revision of Phoreiobothrium (Tetraphyllidea: Onchobothriidae) with descriptions of five new species.

PubMed

Caira, J N; Richmond, C; Swanson, J

2005-10-01

Five new species of Phoreiobothrium (Cestoda: Tetraphyllidea) are described from carcharhiniform sharks collected from a diversity of localities throughout the world. These are Phoreiobothrium perilocrocodilus n. sp. from Negaprion acutidens, Phoreiobothrium anticaporum n. sp. from Negaprion brevirostris, Phoreiobothrium lewinense n. sp. from Sphyrna lewini, Phoreiobothrium robertsoni n. sp. from Carcharhinus brachyurus, and Phoreiobothrium blissorum n. sp. from C. plumbeus, This brings the number of described species of Phoreiobothrium to 17. The new species from the lemon sharks, P. perilocrocodilus n. sp. and P. anticaporum n. sp., both possess more bothridial subloculi than do all species from hammerhead sharks, and fewer subloculi than do all species from sharks of Carcharhinus spp. Phoreiobothrium anticaporum n. sp. is unique among Phoreiobothrium species in that its genital pore is located in the extreme anterior portion of the proglottid. Phoreiobothrium lewinense n. sp. is unique in its possession of a combination of 8-11 subloculi and basal hook prongs that lack internal channels. Phoreiobothrium robertsoni n. sp. possesses 25-29 subloculi, triangular bothridia that flare posteriorly, and hooks that extend well beyond the middle of the bothridia. Phoreiobothrium blissorum n. sp. is most similar to Phoreiobothrium lasium in that it possesses rectangular bothridia with greater than 22 subloculi and long filitriches on its scolex. However, it differs from the latter species in that rather than articulating with one another, the bases of the medial and lateral hooks are widely separated; it also possesses 5-6 (vs.) 7-8 columns of testes. Phoreiobothrium lasium and Phoreiobothrium tiburonis are redescribed. The host associations of P. lasium are reevaluated and a neotype is designated for this species. The mature proglottid of P. tiburonis is described for the first time from voucher material collected from the type host and locality. These data suggest that the proglottid information provided in the original description, which was obtained from detached gravid proglottids, may have come from a tapeworm species other than P. tiburonis. All 7 species treated here in detail were examined with scanning electron microscopy; most were found to exhibit a microthrix pattern similar to that described previously for other members of the genus, e.g., Phoreiobothrium manirei. Bladelike spinitriches were present on the strobila, cephalic peduncle, and proximal bothridial surfaces, but were lacking from the distal bothridial surfaces. These spinitriches varied in length and density among species. Filitriches were present on all of these surfaces, but varied somewhat in length among species. Phoreiobothrium lewinense n. sp. is exceptional in that spinitriches were not seen on the proximal bothridial surfaces. A key to Phoreiobothrium species is provided. This work brings the number of carcharhinid shark species known to host this onchobothriid genus to 6, and the number of sphyrnid species to 5. Like many other onchobothriid tapeworms, species of Phoreiobothrium appear to exhibit oioxenous specificity for their hosts. Given this, and the fact that a total of 9 genera and 46 species of carcharhinid and sphyrnid sharks have yet to be examined for Phoreiobothrium, the diversity of the genus globally is likely to greatly exceed that described to date.

Geophysical Evidence to Link Terrestrial Insect Diversity and Groundwater Availability in Non-Riparian Ecosystems

NASA Astrophysics Data System (ADS)

Pehringer, M.; Carr, G.; Long, H.; Parsekian, A.

2015-12-01

Wyoming, the third driest state in the United States, is home to a high level of biodiversity. In many cases, ecosystems are dependent on the vast systems of water resting just below the surface. This groundwater supports a variety of organisms that live far from surface water and its surrounding riparian zone, where more than 70% of species reside. In order to observe the correlation of groundwater presence and biodiversity in non-riparian ecosystems, a study was conducted to look specifically at terrestrial insect species linked to groundwater in Bighorn National Forest, WY. It was hypothesized that the more groundwater present, the greater the diversity of insects would be. Sample areas were randomly selected in non-riparian zones and groundwater was evaluated using a transient electromagnetic (TEM) geophysical instrument. Electrical pulses were transmitted through a 40m by 40m square of wire to measure levels of resistivity from near the surface to several hundred meters below ground. Pulses are echoed back to the surface and received by a smaller 10m by 10m square of wire, and an even smaller 1m by 1m square of wire set inside the larger transmitting wire. An insect population and species count was then conducted within the perimeter set by the outer transmitting wire. The results were not as hypothesized. More inferred groundwater below the surface resulted in a smaller diversity of species. Inversely, the areas with a smaller diversity held a larger total population of terrestrial insects.

Prevention of pink-pigmented methylotrophic bacteria (Methylohacterium mesophilicum) contamination of plant tissue cultures.

PubMed

Chanprame, S; Todd, J J; Widholm, J M

1996-12-01

Pink-pigmented facultative methylotrophic bacteria (PPFMs) have been found on the surfaces of leaves of most plants tested. We found PPFMs on the leaf surfaces of all 40 plants (38 species) tested and on soybean pods by pressing onto AMS medium with methanol as the sole carbon source. The abundance ranged from 0.5 colony forming unit (cfu) /cm(2) to 69.4 cfu/cm(2) on the leaf surfaces. PPFMs were found in homogenized leaf tissues of only 4 of the species after surface disinfestation with 1.05% sodium hypochlorite and were rarely found in cultures initiated from surface disinfested Datura innoxia leaves or inside surface disinfested soybean pods. Of 20 antibiotics tested for PPFM growth inhibition, rifampicin was the most effective and of seven others which also inhibited PPFM growth, cefotaxime should be the most useful due to the expected low plant cell toxicity. These antibiotics could be used in concert with common surface sterilization procedures to prevent the introduction or to eliminate PPFM bacteria in tissue cultures. Thus, while PPFMs are present on the surfaces of most plant tissues, surface disinfestation alone can effectively remove them so that uncontaminated tissue cultures can be initiated in most cases.

The production of oxidants in Europa's surface.

PubMed

Johnson, R E; Quickenden, T I; Cooper, P D; McKinley, A J; Freeman, C G

2003-01-01

The oxidants produced by radiolysis and photolysis in the icy surface of Europa may be necessary to sustain carbon-based biochemistry in Europa's putative subsurface ocean. Because the subduction of oxidants to the ocean presents considerable thermodynamic challenges, we examine the formation of oxygen and related species in Europa's surface ice with the goal of characterizing the chemical state of the irradiated material. Relevant spectral observations of Europa and the laboratory data on the production of oxygen and related species are first summarized. Since the laboratory data are incomplete, we examine the rate equations for formation of oxygen and its chemical precursors by radiolysis and photolysis. Measurements and simple rate equations are suggested that can be used to characterize the production of oxidants in Europa's surface material and the chemical environment produced by radiolysis. Possible precursor molecules and the role of radical trapping are examined. The possibility of oxygen reactions on grain surfaces in Europa's regolith is discussed, and the earlier estimates of the supply of O(2) to the atmosphere are increased.

The fundamental surface science of wurtzite gallium nitride

NASA Astrophysics Data System (ADS)

Bermudez, V. M.

2017-09-01

A review is presented that covers the experimental and theoretical literature relating to the preparation, electronic structure and chemical and physical properties of the surfaces of the wurtzite form of GaN. The discussion includes the adsorption of various chemical elements and of inorganic, organometallic and organic species. The focus is on work that contributes to a microscopic, atomistic understanding of GaN surfaces and interfaces, and the review concludes with an assessment of possible future directions.

Chemical evolution on Titan: comparisons to the prebiotic earth.

PubMed

Clarke, D W; Ferris, J P

1997-06-01

Models for the origin of Titan's atmosphere, the processing of the atmosphere and surface and its exobiological role are reviewed. Titan has gained widespread acceptance in the origin of life field as a model for the types of evolutionary processes that could have occurred on prebiotic Earth. Both Titan and Earth possess significant atmospheres (> or = 1 atm) composed mainly of molecular nitrogen with smaller amounts of more reactive species. Both of these atmospheres are processed primarily by solar ultraviolet light with high energy particles interactions contributing to a lesser extent. The products of these reactions condense or are dissolved in other atmospheric species (aerosols/clouds) and fall to the surface. There these products may have been further processed on Titan and the primitive Earth by impacting comets and meteorites. While the low temperatures on Titan (approximately 72-180 K) preclude the presence of permanent liquid water on the surface, it has been suggested that tectonic activity or impacts by meteors and comets could produce liquid water pools on the surface for thousands of years. Hydrolysis and oligomerization reactions in these pools might form chemicals of prebiological significance. Other direct comparisons between the conditions on present day Titan and those proposed for prebiotic Earth are also presented.

Articles including thin film monolayers and multilayers

DOEpatents

Li, DeQuan; Swanson, Basil I.

1995-01-01

Articles of manufacture including: (a) a base substrate having an oxide surface layer, and a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, (b) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, and a metal species attached to the multidentate ligand, (c) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, a metal species attached to the multidentate ligand, and a multifunctional organic ligand attached to the metal species, and (d) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, a metal species attached to the multidentate ligand, a multifunctional organic ligand attached to the metal species, and a second metal species attached to the multifunctional organic ligand, are provided, such articles useful in detecting the presence of a selected target species, as nonliear optical materials, or as scavengers for selected target species.

1-D DSMC simulation of Io's atmospheric collapse and reformation during and after eclipse

NASA Astrophysics Data System (ADS)

Moore, C. H.; Goldstein, D. B.; Varghese, P. L.; Trafton, L. M.; Stewart, B.

2009-06-01

A one-dimensional Direct Simulation Monte Carlo (DSMC) model is used to examine the effects of a non-condensable species on Io's sulfur dioxide sublimation atmosphere during eclipse and just after egress. Since the vapor pressure of SO 2 is extremely sensitive to temperature, the frost-supported dayside sublimation atmosphere had generally been expected to collapse during eclipse as the surface temperature dropped. For a pure SO 2 atmosphere, however, it was found that during the first 10 min of eclipse, essentially no change in the atmospheric properties occurs at altitudes above ˜100 km due to the finite ballistic/acoustic time. Hence immediately after ingress the auroral emission morphology above 100 km should resemble that of the immediate pre-eclipse state. Furthermore, the collapse dynamics are found to be greatly altered by the presence of even a small amount of a non-condensable species which forms a diffusion layer near the surface that prevents rapid collapse. It is found that after 10 min essentially no collapse has occurred at altitudes above ˜20 km when a nominal mole fraction of non-condensable gas is present. Collapse near the surface occurs relatively quickly until a static diffusion layer many mean free paths thick of the non-condensable gas builds up which then retards further collapse of the SO 2 atmosphere. For example, for an initial surface temperature of 110 K and 35% non-condensable mole-fraction, the ratio of the SO 2 column density to the initial column density was found to be 0.73 after 10 min, 0.50 after 30 min, and 0.18 at the end of eclipse. However, real gas species (SO, O 2) may not be perfectly non-condensable at Io's surface temperatures. If the gas species was even weakly condensable (non-zero sticking/reaction coefficient) then the effect of the diffusion layer on the dynamics was dramatically reduced. In fact, if the sticking coefficient of the non-condensable exceeds ˜0.25, the collapse dynamics are effectively the same as if there were no non-condensable present. This sensitivity results because the loss of non-condensable to the surface reduces the effective diffusion layer size, and the formation of an effective diffusion layer requires that the layer be stationary; this does not occur if the surface is a sink. Upon egress, vertical stratification of the condensable and non-condensable species occurs, with the non-condensable species being lifted (or pushed) to higher altitudes by the sublimating SO 2 after the sublimating atmosphere becomes collisional. Stratification should affect the morphology and intensity of auroral glows shortly after egress.

Stabilization of electrogenerated copper species on electrodes modified with quantum dots.

PubMed

Martín-Yerga, Daniel; Costa-García, Agustín

2017-02-15

Quantum dots (QDs) have special optical, surface, and electronic properties that make them useful for electrochemical applications. In this work, the electrochemical behavior of copper in ammonia medium is described using bare screen-printed carbon electrodes and the same modified with CdSe/ZnS QDs. At the bare electrodes, the electrogenerated Cu(i) and Cu(0) species are oxidized by dissolved oxygen in a fast coupled chemical reaction, while at the QDs-modified electrode, the re-oxidation of Cu(i) and Cu(0) species can be observed, which indicates that they are stabilized by the nanocrystals present on the electrode surface. A weak adsorption is proposed as the main cause for this stabilization. The electrodeposition on electrodes modified with QDs allows the generation of random nanostructures with copper nanoparticles, avoiding the preferential nucleation onto the most active electrode areas.

Molecular dynamics simulations of energy dissipation and non-thermal diffusion on amorphous solid water.

PubMed

Fredon, A; Cuppen, H M

2018-02-21

Molecules in space are synthesized via a large variety of gas-phase reactions, and reactions on dust-grain surfaces, where the surface acts as a catalyst. Especially, saturated, hydrogen-rich molecules are formed through surface chemistry where the interstellar grains act as a meeting place and absorbing energy. Here we present the results of thousands of molecular dynamics simulations to quantify the outcome of an energy dissipation process. Admolecules on top of an amorphous solid water surface have been given translational energy between 0.5 and 5 eV. Three different surface species are considered, CO 2 , H 2 O and CH 4 , spanning a range in binding energies, number of internal degrees of freedom and molecular weight. The results are compared against a previous study using a crystalline water ice surface. Possible outcomes of a dissipation process are adsorption - possibly after long-range diffusion-, desorption and desorption of a surface molecule. The three admolecules were found to bind at different locations on the surface, particularly in terms of height. Water preferably binds on top of the surface, whereas methane fills the nanopores on the surface. This has direct consequences for desorption, travelled distance, and kick-out probabilities. The admolecules are found to frequently travel several tens of angstroms before stabilizing on a binding site, allowing follow-up reactions en route. We present kick-out probabilities and we have been able to quantify the desorption probability which depends on the binding energy of the species, the translational excitation, and a factor that accounts for difference in binding site height. We provide expressions that can be incorporated in astrochemical models to predict grain surface formation and return into the gas phase of these products.

Influence of habitat structure and nature of substratum on limpet recruitment: Conservation implications for endangered species

NASA Astrophysics Data System (ADS)

Espinosa, Free; Rivera-Ingraham, Georgina; García-Gómez, Jose C.

2011-08-01

Habitat complexity has been recognised to exert a significant influence on the abundance and diversity of benthic invertebrates. This issue is especially important for the management of endangered species. The recruitment of limpet species was monitored monthly for one year on natural and artificial surfaces. Control plots showed the highest mean number of species and individuals settled per plot, followed by rough then smooth plots. Control plots presented the highest mean diversity values followed by rough and smooth plots. Recruits of the endangered limpet Patella ferruginea were mainly observed during the spring, from April to June. Recruitment seemed to be influenced by both the heterogeneity and nature of the substratum. P. ferruginea repopulation programmes involving the translocation of recruits on experimental plates should be conducted using similar materials to the natural substratum, such as granite or limestone, rather than plastic, avoiding surfaces with low levels of heterogeneity, and taking into account that translocation of adults is not feasible due to the high mortality observed.

Field and laboratory arsenic speciation methods and their application to natural-water analysis

USGS Publications Warehouse

Bednar, A.J.; Garbarino, J.R.; Burkhardt, M.R.; Ranville, J.F.; Wildeman, T.R.

2004-01-01

The toxic and carcinogenic properties of inorganic and organic arsenic species make their determination in natural water vitally important. Determination of individual inorganic and organic arsenic species is critical because the toxicology, mobility, and adsorptivity vary substantially. Several methods for the speciation of arsenic in groundwater, surface-water, and acid mine drainage sample matrices using field and laboratory techniques are presented. The methods provide quantitative determination of arsenite [As(III)], arsenate [As(V)], monomethylarsonate (MMA), dimethylarsinate (DMA), and roxarsone in 2-8min at detection limits of less than 1??g arsenic per liter (??g AsL-1). All the methods use anion exchange chromatography to separate the arsenic species and inductively coupled plasma-mass spectrometry as an arsenic-specific detector. Different methods were needed because some sample matrices did not have all arsenic species present or were incompatible with particular high-performance liquid chromatography (HPLC) mobile phases. The bias and variability of the methods were evaluated using total arsenic, As(III), As(V), DMA, and MMA results from more than 100 surface-water, groundwater, and acid mine drainage samples, and reference materials. Concentrations in test samples were as much as 13,000??g AsL-1 for As(III) and 3700??g AsL-1 for As(V). Methylated arsenic species were less than 100??g AsL-1 and were found only in certain surface-water samples, and roxarsone was not detected in any of the water samples tested. The distribution of inorganic arsenic species in the test samples ranged from 0% to 90% As(III). Laboratory-speciation method variability for As(III), As(V), MMA, and DMA in reagent water at 0.5??g AsL-1 was 8-13% (n=7). Field-speciation method variability for As(III) and As(V) at 1??g AsL-1 in reagent water was 3-4% (n=3). ?? 2003 Elsevier Ltd. All rights reserved.

Ab initio investigation of the surface properties of austenitic Fe-Ni-Cr alloys in aqueous environments

NASA Astrophysics Data System (ADS)

Rák, Zs.; Brenner, D. W.

2017-04-01

The surface energetics of two austenitic stainless steel alloys (Type 304 and 316) and three Ni-based alloys (Alloy 600, 690, and 800) are investigated using theoretical methods within the density functional theory. The relative stability of the low index surfaces display the same trend for all alloys; the most closely packed orientation and the most stable is the (111), followed by the (100) and the (110) surfaces. Calculations on the (111) surfaces using various surface chemical and magnetic configurations reveal that Ni has the tendency to segregate toward the surface and Cr has the tendency to segregate toward the bulk. The magnetic frustration present on the (111) surfaces plays an important role in the observed segregation tendencies of Ni and Cr. The stability of the (111) surfaces in contact with aqueous solution are evaluated as a function of temperature, pH, and concentration of aqueous species. The results indicate that the surface stability of the alloys decrease with temperature and pH, and increase slightly with concentration. Under conditions characteristic to an operating pressurized water reactor, the Ni-based alloy series appears to be of better quality than the stainless steel series with respect to corrosion resistance and release of aqueous species when in contact with aqueous solutions.

Diversity of yeasts associated with the sea surface microlayer and underlying water along the northern coast of Taiwan.

PubMed

Chang, Chin-Feng; Lee, Ching-Fu; Lin, Kao-Yung; Liu, Shiu-Mei

2016-01-01

Yeast communities inhabiting the sea surface microlayer (SSML) on the northern coast of Taiwan were examined using a cultivation method and compared with those inhabiting the underlying water (UW) at a 50-cm depth. Culturable yeasts were recovered from the SSML and UW samples collected in the morning during 4 field campaigns, and 420 strains were isolated. The 420 isolates were grouped into 43 species using a polyphasic molecular approach, including sequence analysis of the 26S rDNA D1/D2 domain and 5.8S-ITS region. From the SSML samples, 12 genera and 39 species, including 7 new species of Cryptococcus sp. (1), Candida spp. (4), and Rhodotorula spp. (2), were isolated. From the UW samples, 10 genera and 21 species, including one new species of Rhodotorula sp. (1), were isolated. Rhodotorula mucilaginosa was the most abundant species present in the yeast community in SSML (37.6%) and UW (21.6%) samples. Basidiomycetous yeasts (63.6%) and pigmented yeasts (64.5%) comprised the major yeast population. The yeast community in the SSML had a higher species number and abundance than the UW. Moreover, although the majority of yeast community species were from the SSML, individual species distribution in the SSML was unequal. Copyright © 2015 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Invited Article: Quantitative imaging of explosions with high-speed cameras

DOE PAGES

McNesby, Kevin L.; Homan, Barrie E.; Benjamin, Richard A.; ...

2016-05-31

Here, the techniques presented in this paper allow for mapping of temperature, pressure, chemical species, and energy deposition during and following detonations of explosives, using high speed cameras as the main diagnostic tool. Additionally, this work provides measurement in the explosive near to far-field (0-500 charge diameters) of surface temperatures, peak air-shock pressures, some chemical species signatures, shock energy deposition, and air shock formation.

Adhesion of Porphyromonas gingivalis and Tannerella forsythia to dentin and titanium with sandblasted and acid etched surface coated with serum and serum proteins - An in vitro study.

PubMed

Eick, Sigrun; Kindblom, Christian; Mizgalska, Danuta; Magdoń, Anna; Jurczyk, Karolina; Sculean, Anton; Stavropoulos, Andreas

2017-03-01

To evaluate the adhesion of selected bacterial strains incl. expression of important virulence factors at dentin and titanium SLA surfaces coated with layers of serum proteins. Dentin- and moderately rough SLA titanium-discs were coated overnight with human serum, or IgG, or human serum albumin (HSA). Thereafter, Porphyromonas gingivalis, Tannerella forsythia, or a six-species mixture were added for 4h and 24h. The number of adhered bacteria (colony forming units; CFU) was determined. Arg-gingipain activity of P. gingivalis and mRNA expressions of P. gingivalis and T. forsythia proteases and T. forsythia protease inhibitor were measured. Coating specimens never resulted in differences exceeding 1.1 log10 CFU, comparing to controls, irrespective the substrate. Counts of T. forsythia were statistically significantly higher at titanium than dentin, the difference was up to 3.7 log10 CFU after 24h (p=0.002). No statistically significant variation regarding adhesion of the mixed culture was detected between surfaces or among coatings. Arg-gingipain activity of P. gingivalis was associated with log10 CFU but not with the surface or the coating. Titanium negatively influenced mRNA expression of T. forsythia protease inhibitor at 24h (p=0.026 uncoated, p=0.009 with serum). The present findings indicate that: a) single bacterial species (T. forsythia) can adhere more readily to titanium SLA than to dentin, b) low expression of T. forsythia protease inhibitor may influence the virulence of the species on titanium SLA surfaces in comparison with teeth, and c) surface properties (e.g. material and/or protein layers) do not appear to significantly influence multi-species adhesion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Oxygen transport in the internal xenon plasma of a dispenser hollow cathode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Capece, Angela M., E-mail: acapece@pppl.gov; Shepherd, Joseph E.; Polk, James E.

2014-04-21

Reactive gases such as oxygen and water vapor modify the surface morphology of BaO dispenser cathodes and degrade the electron emission properties. For vacuum cathodes operating at fixed temperature, the emission current drops rapidly when oxygen adsorbs on top of the low work function surface. Previous experiments have shown that plasma cathodes are more resistant to oxygen poisoning and can operate with O{sub 2} partial pressures one to two orders of magnitude higher than vacuum cathodes before the onset of poisoning occurs. Plasma cathodes used for electric thrusters are typically operated with xenon; however, gas phase barium, oxygen, and tungstenmore » species may be found in small concentrations. The densities of these minor species are small compared with the plasma density, and thus, their presence in the discharge does not significantly alter the xenon plasma parameters. It is important, however, to consider the transport of these minor species as they may deposit on the emitter surface and affect the electron emission properties. In this work, we present the results of a material transport model used to predict oxygen fluxes to the cathode surface by solving the species conservation equations in a cathode with a 2.25 mm diameter orifice operated at a discharge current of 15 A, a Xe flow rate of 3.7 sccm, and 100 ppm of O{sub 2}. The dominant ionization process for O{sub 2} is resonant charge exchange with xenon ions. Ba is effectively recycled in the plasma; however, BaO and O{sub 2} are not. The model shows that the oxygen flux to the surface is not diffusion-limited; therefore, the high resistance to oxygen poisoning observed in plasma cathodes likely results from surface processes not considered here.« less

Monte Carlo simulation to investigate the formation of molecular hydrogen and its deuterated forms

NASA Astrophysics Data System (ADS)

Sahu, Dipen; Das, Ankan; Majumdar, Liton; Chakrabarti, Sandip K.

2015-07-01

H2 is the most abundant interstellar species, and its deuterated forms (HD and D2) are also present in high abundance. The high abundance of these molecules could be explained by considering the chemistry that occurs on interstellar dust. Because of its simplicity, the rate equation method is widely used to study the formation of grain-surface species. However, because the recombination efficiency for the formation of any surface species is highly dependent on various physical and chemical parameters, the Monte Carlo method is best suited for addressing the randomness of the processes. We perform Monte Carlo simulations to study the formation of H2, HD and D2 on interstellar ice. The adsorption energies of surface species are the key inputs for the formation of any species on interstellar dusts, but the binding energies of deuterated species have yet to be determined with certainty. A zero-point energy correction exists between hydrogenated and deuterated species, which should be considered during modeling of the chemistry on interstellar dusts. Following some previous studies, we consider various sets of adsorption energies to investigate the formation of these species under diverse physical conditions. As expected, notable differences in these two approaches (rate equation method and Monte Carlo method) are observed for the production of these simple molecules on interstellar ice. We introduce two factors, namely, Sf and β , to explain these discrepancies: Sf is a scaling factor, which can be used to correlate the discrepancies between the rate equation and Monte Carlo methods, and β indicates the formation efficiency under various conditions. Higher values of β indicate a lower production efficiency. We observed that β increases with a decrease in the rate of accretion from the gas phase to the grain phase.

Composition, structure, and chemistry of interstellar dust

NASA Technical Reports Server (NTRS)

Tielens, A. G. G. M.; Allamandola, L. J.

1987-01-01

Different dust components present in the interstellar medium (IM) such as amorphous carbon, polycyclic aromatic hydrocarbons, and those IM components which are organic refractory grains and icy grain mantles are discussed as well as their relative importance. The physical properties of grain surface chemistry are discussed with attention given to the surface structure of materials, the adsorption energy and residence time of species on a grain surface, and the sticking probability. Consideration is also given to the contribution of grains to the gas-phase composition of molecular clouds.

Nitrile versus isonitrile adsorption at interstellar grain surfaces. II. Carbonaceous aromatic surfaces

NASA Astrophysics Data System (ADS)

Bertin, M.; Doronin, M.; Michaut, X.; Philippe, L.; Markovits, A.; Fillion, J.-H.; Pauzat, F.; Ellinger, Y.; Guillemin, J.-C.

2017-12-01

Context. Almost 20% of the 200 different species detected in the interstellar and circumstellar media present a carbon atom linked to nitrogen by a triple bond. Of these 37 molecules, 30 are nitrile R-CN compounds, the remaining 7 belonging to the isonitrile R-NC family. How these species behave in their interactions with the grain surfaces is still an open question. Aims: In a previous work, we have investigated whether the difference between nitrile and isonitrile functional groups may induce differences in the adsorption energies of the related isomers at the surfaces of interstellar grains of various nature and morphologies. This study is a follow up of this work, where we focus on the adsorption on carbonaceous aromatic surfaces. Methods: The question is addressed by means of a concerted experimental and theoretical approach of the adsorption energies of CH3CN and CH3NC on the surface of graphite (with and without surface defects). The experimental determination of the molecule and surface interaction energies is carried out using temperature-programmed desorption in an ultra-high vacuum between 70 and 160 K. Theoretically, the question is addressed using first-principle periodic density functional theory to represent the organised solid support. Results: The adsorption energy of each compound is found to be very sensitive to the structural defects of the aromatic carbonaceous surface: these defects, expected to be present in a large numbers and great diversity on a realistic surface, significantly increase the average adsorption energies to more than 50% as compared to adsorption on perfect graphene planes. The most stable isomer (CH3CN) interacts more efficiently with the carbonaceous solid support than the higher energy isomer (CH3NC), however.

Double layer of platinum electrodes: Non-monotonic surface charging phenomena and negative double layer capacitance

NASA Astrophysics Data System (ADS)

Huang, Jun; Zhou, Tao; Zhang, Jianbo; Eikerling, Michael

2018-01-01

In this study, a refined double layer model of platinum electrodes accounting for chemisorbed oxygen species, oriented interfacial water molecules, and ion size effects in solution is presented. It results in a non-monotonic surface charging relation and a peculiar capacitance vs. potential curve with a maximum and possibly negative values in the potential regime of oxide-formation.

Method and apparatus for confinement of ions in the presence of a neutral gas

DOEpatents

Peurrung, Anthony J.; Barlow, Stephan E.

1999-01-01

The present invention is an apparatus and method for combining ions with a neutral gas and flowing the mixture with a radial flow component through a magnetic field so that the weakly ionized gas is confined by the neutral gas. When the weakly ionized gas is present in sufficient density, a weakly ionized non-neutral plasma is formed that may be trapped in accordance with the present invention. Applications for a weakly ionized non-neutral plasma exploit the trap's ability to store and manipulate ionic species in the presence of neutral gas. The trap may be connected to a mass spectrometer thereby permitting species identification after a fixed period of time. Delicate and/or heavy particles such as clusters may be held and studied in a "gentle" environment. In addition, the trap can provide a relatively intense, low-energy source of a particular ion species for surface implantation or molecular chemistry. Finally, a long trap may permit spectroscopy of unprecedented accuracy to be performed on ionic species.

Physical and biological mechanisms of nanosecond- and microsecond-pulsed FE-DBD plasma interaction with biological objects

NASA Astrophysics Data System (ADS)

Dobrynin, Danil

2013-09-01

Mechanisms of plasma interaction with living tissues and cells can be quite complex, owing to the complexity of both the plasma and the tissue. Thus, unification of all the mechanisms under one umbrella might not be possible. Here, analysis of interaction of floating electrode dielectric barrier discharge (FE-DBD) with living tissues and cells is presented and biological and physical mechanisms are discussed. In physical mechanisms, charged species are identified as the major contributors to the desired effect and a mechanism of this interaction is proposed. Biological mechanisms are also addressed and a hypothesis of plasma selectivity and its effects is offered. Spatially uniform nanosecond and sub-nanosecond short-pulsed dielectric barrier discharge plasmas are gaining popularity in biological and medical applications due to their increased uniformity, lower plasma temperature, lower surface power density, and higher concentration of the active species produced. In this presentation we will compare microsecond pulsed plasmas with nanosecond driven systems and their applications in biology and medicine with specific focus on wound healing and tissue regeneration. Transition from negative to positive streamer will be discussed with proposed hypothesis of uniformity mechanisms of positive streamer and the reduced dependence on morphology and surface chemistry of the second electrode (human body) being treated. Uniform plasma offers a more uniform delivery of active species to the tissue/surface being treated thus leading to better control over the biological results.

Light triggers habitat choice of eyeless subterranean but not of eyed surface amphipods.

PubMed

Fišer, Žiga; Novak, Luka; Luštrik, Roman; Fišer, Cene

2016-02-01

Boundaries of species distributions are the result of colonization-extinction processes. Survival on the boundary depends on how well individuals discriminate optimal from suboptimal habitat patches. Such behaviour is called habitat choice and was only rarely applied to macroecology, although it links species ecological niche and species distribution. Surface and subterranean aquatic species are spatially strongly segregated, even in the absence of physical barriers. We explored whether a behavioural response to light functions as a habitat choice mechanism that could explain species turnover between surface and subterranean aquatic ecosystems. In a controlled laboratory experiment, we studied the behavioural response to light of ten pairs of surface and subterranean amphipods that permanently co-occur in springs. Surface species showed a weak photophobic, photoneutral, and in one case, photophilic response, whereas all subterranean species showed a strong photophobic response. Eyeless subterranean but not eyed surface amphipods appear to orient themselves with light cues. On a local scale, this difference possibly diminishes harmful interactions between the co-occurring amphipods, whereas on a regional scale, photophobia could explain limited dispersal and a high degree of endemism observed among subterranean species.

Wettability shifts caused by CO2 aging on mineral surfaces

NASA Astrophysics Data System (ADS)

Liang, B.; Clarens, A. F.

2015-12-01

Interfacial forces at the CO2/brine/mineral ternary interface have a well-established impact on multiphase flow properties through porous media. In the context of geologic carbon sequestration, this wettability will impact capillary pressure, residual trapping, and a variety of other key parameters of interest. While the wettability of CO2 on pure mineral and real rock sample have been studied a great deal over the past few year, very little is known about how the wettability of these rocks could change over long time horizons as CO2 interacts with species in the brine and on the mineral surface. In this work we sought to explore the role that dilute inorganic and organic species that are likely to exist in connate brines might have on a suite of mineral species. High-pressure contact angle experiments were carried out on a suite of polished mineral surfaces. Both static captive bubble and advancing/receding contact angle measurements were carried out. The effect of ionic strength, and in particular the valence of the dominant ions in the brine are found to have an important impact on the wettability which cannot be explained solely based on the shifts in the interfacial tension between the CO2 and brine. More significantly, three organic species, formate, acetate, and oxalate, all three of which are representative species commonly encountered in the saline aquifers that are considered target repositories for carbon sequestration. All three organic species show impacts on wettability, with the organics generally increasing the CO2 wetting of the mineral surface. Not all pure minerals respond the same to the presence of organics, with micas showing a more pronounced influence than quartz. Sandstone and limestone samples aged with different kinds of hydrocarbons, a surrogate for oil-bearing rocks, are generally more CO2-wet, with larger contact angles in the CO2/brine system. Over multiple days, the contact angle decreases, which could be attributed to partitioning of oil films off of the surface and into the CO2 phase, which drives the wettability towards the original water-wet state. This effect could be particularly important for organic rich repositories like depleted oil and gas fields or fractured shale formations where organic species could be presented both on mineral surfaces and in the aqueous phase.

Mitigation of radiation induced surface contamination

DOEpatents

Klebanoff, Leonard E.; Stulen, Richard H.

2003-01-01

A process for mitigating or eliminating contamination and/or degradation of surfaces having common, adventitious atmospheric contaminants adsorbed thereon and exposed to radiation. A gas or a mixture of gases is introduced into the environment of a surface(s) to be protected. The choice of the gaseous species to be introduced (typically a hydrocarbon gas, water vapor, or oxygen or mixtures thereof) is dependent upon the contaminant as well as the ability of the gaseous species to bind to the surface to be protected. When the surface and associated bound species are exposed to radiation reactive species are formed that react with surface contaminants such as carbon or oxide films to form volatile products (e.g., CO, CO.sub.2) which desorb from the surface.

Distinctive bacterial communities in the rhizoplane of four tropical tree species.

PubMed

Oh, Yoon Myung; Kim, Mincheol; Lee-Cruz, Larisa; Lai-Hoe, Ang; Go, Rusea; Ainuddin, N; Rahim, Raha Abdul; Shukor, Noraini; Adams, Jonathan M

2012-11-01

It is known that the microbial community of the rhizosphere is not only influenced by factors such as root exudates, phenology, and nutrient uptake but also by the plant species. However, studies of bacterial communities associated with tropical rainforest tree root surfaces, or rhizoplane, are lacking. Here, we analyzed the bacterial community of root surfaces of four species of native trees, Agathis borneensis, Dipterocarpus kerrii, Dyera costulata, and Gnetum gnemon, and nearby bulk soils, in a rainforest arboretum in Malaysia, using 454 pyrosequencing of the 16S rRNA gene. The rhizoplane bacterial communities for each of the four tree species sampled clustered separately from one another on an ordination, suggesting that these assemblages are linked to chemical and biological characteristics of the host or possibly to the mycorrhizal fungi present. Bacterial communities of the rhizoplane had various similarities to surrounding bulk soils. Acidobacteria, Alphaproteobacteria, and Betaproteobacteria were dominant in rhizoplane communities and in bulk soils from the same depth (0-10 cm). In contrast, the relative abundance of certain bacterial lineages on the rhizoplane was different from that in bulk soils: Bacteroidetes and Betaproteobacteria, which are known as copiotrophs, were much more abundant in the rhizoplane in comparison to bulk soil. At the genus level, Burkholderia, Acidobacterium, Dyella, and Edaphobacter were more abundant in the rhizoplane. Burkholderia, which are known as both pathogens and mutualists of plants, were especially abundant on the rhizoplane of all tree species sampled. The Burkholderia species present included known mutualists of tropical crops and also known N fixers. The host-specific character of tropical tree rhizoplane bacterial communities may have implications for understanding nutrient cycling, recruitment, and structuring of tree species diversity in tropical forests. Such understanding may prove to be useful in both tropical forestry and conservation.

Infrared Spectral Studies of the Thermally-Driven Chemistry Present on Icy Satellites

NASA Technical Reports Server (NTRS)

Loeffler, Mark J.; Hudson, Reggie L.

2012-01-01

Remote sensing of Jupiters icy satellites has revealed that even though their surfaces arc composed mostly of water ice, molecules such as SO2, CO2, H2O2. O2, and O3 also are present. On Europa, a high radiation flux is believed to play a role in the formation of many of the minor species detected, and numerous laboratory studies have been devoted to explore this hypothesis. In this presentation we will discuss some of our recent research on another alteration pathway, thermally-driven chemical reactions, which are also important for understanding the chemical evolution of Europa's surface and sub-surface ices. We will focus on the infrared spectra of and reactions between H2O, SO2 and H2O2, at 80 - 130 K.

Solar Wind sputtering from the surface of Comet Churyumov-Gerasimenko

NASA Astrophysics Data System (ADS)

Wurz, Peter; Rubin, Martin; Altwegg, Kathrin; Balsiger, Hans; Gasc, Sébastien; Galli, André; Jäckel, Annette; Le Roy, Lena; Calmonte, Ursina; Tzou, Chia-Yu; Mall, Urs; Korth, Axel; Fiethe, Björn; De Keyser, Johan; Berthelier, Jean-Jacques; Rème, Henri; Gombosi, Tamas; Fuselier, Steven

2015-04-01

While the European Space Agency's Rosetta spacecraft is orbiting close to the comet 67P/Churyumov-Gerasimenko (67P/C-G) we performed continuous measurements of the chemical inventory of its coma with the the Rosetta Orbiter Spectrometer for Ion and Neutral Analysis (ROSINA) instrument suite. ROSINA consists of two mass spectrometers, the Double Focusing Mass Spectrometer (DFMS) and the Reflectron-type Time-Of-Flight (RTOF), as well as the COmet Pressure Sensor (COPS). Most of the observed species in the coma are volatile material that are released from the comet's surface by sublimation, for example H2O, CO, CO2 and many others. The number densities in the coma of these species show temporary variation compatible with the solar illumination (diurnal cycle), with seasonal variation (summer and winter hemispheres), and with compositional heterogeneity of the surface. We can trace back the measurements of the observed species to the cometary surface to create maps of their probable origin on the surface. In addition to the volatile material we detected atoms of Na, K, Si, S, and some more, which cannot or only partially be set free via sublimation. Again, we project these measurements down onto the surface of the comet. These maps for the sputtered atoms differ significantly from the maps for volatile species, like the water map, in some cases they are almost the opposite. Our present understanding is that these atoms are the result of solar wind sputtering of refractory material, i.e., of dust located on the cometary surface. Since the release of material from the surface by sputtering is almost stoichiometric we can infer the chemical composition of major elements for the areas affected by sputtering and the average mineralogy of these locations can be derived. The sputter signal will disappear with the comet getting closer to the Sun and becomes more active. Once the coma is dense enough, the solar wind will be absorbed by the gas layer above the surface and will not propagate to the surface anymore.

Sorption-desorption of antimony species onto calcined hydrotalcite: Surface structure and control of competitive anions.

PubMed

Constantino, Leonel Vinicius; Quirino, Juliana Nunes; Abrão, Taufik; Parreira, Paulo Sérgio; Urbano, Alexandre; Santos, Maria Josefa

2018-02-15

Calcined hydrotalcite can be applied to remove anionic contaminants from aqueous systems such as antimony species due to its great anion exchange capacity and high surface area. Hence, this study evaluated antimonite and antimonate sorption-desorption processes onto calcined hydrotalcite in the presence of nitrate, sulfate and phosphate. Sorption and desorption experiments of antimonite and antimonate were carried out in batch equilibrium and the post-sorption solids were analyzed by X-ray fluorescence (EDXRF). Sorption data were better fitted by dual-mode Langmuir-Freundlich model (R 2 >0.99) and desorption data by Langmuir model. High maximum sorption capacities were found for the calcined hydrotalcite, ranging from 617 to 790meqkg -1 . The competing anions strongly affected the antimony sorption. EDXRF analysis and mathematical modelling showed that sulfate and phosphate presented higher effect on antimonite and antimonate sorption, respectively. High values for sorption efficiency (SE=99%) and sorption capacity were attributed to the sorbent small particles and the large surface area. Positive hysteresis indexes and low mobilization factors (MF>3%) suggest very low desorption capacity to antimony species from LDH. These calcined hydrotalcite characteristics are desirable for sorption of antimony species from aqueous solutions. Copyright © 2017. Published by Elsevier B.V.

Systematic, Cross-Cortex Variation in Neuron Numbers in Rodents and Primates

PubMed Central

Charvet, Christine J.; Cahalane, Diarmuid J.; Finlay, Barbara L.

2015-01-01

Uniformity, local variability, and systematic variation in neuron numbers per unit of cortical surface area across species and cortical areas have been claimed to characterize the isocortex. Resolving these claims has been difficult, because species, techniques, and cortical areas vary across studies. We present a stereological assessment of neuron numbers in layers II–IV and V–VI per unit of cortical surface area across the isocortex in rodents (hamster, Mesocricetus auratus; agouti, Dasyprocta azarae; paca, Cuniculus paca) and primates (owl monkey, Aotus trivigratus; tamarin, Saguinus midas; capuchin, Cebus apella); these chosen to vary systematically in cortical size. The contributions of species, cortical areas, and techniques (stereology, “isotropic fractionator”) to neuron estimates were assessed. Neurons per unit of cortical surface area increase across the rostro-caudal (RC) axis in primates (varying by a factor of 1.64–2.13 across the rostral and caudal poles) but less in rodents (varying by a factor of 1.15–1.54). Layer II–IV neurons account for most of this variation. When integrated into the context of species variation, and this RC gradient in neuron numbers, conflicts between studies can be accounted for. The RC variation in isocortical neurons in adulthood mirrors the gradients in neurogenesis duration in development. PMID:23960207

Dielectrophoresis-Based Particle Sensor Using Nanoelectrode Arrays

NASA Technical Reports Server (NTRS)

Li, Jun; Cassell, Alan M.; Arumugam, Prabhu U.

2013-01-01

A method has been developed for concentrating, or partly separating, particles of a selected species from a liquid or gas containing these particles, and flowing in a channel. An example of this is to promote an accumulation (and thus concentration) of the selected particle (e.g., biological species such as E. coli, salmonella, anthrax, tobacco mosaic virus or herpes simplex, and non-biological materials such as nano- and microparticles, quantum dots, nanowires, nano - tubes, and other inorganic particles) adjacent to the first surface. Additionally, this method can also determine if the particle species is present in the liquid. This is accomplished by providing an insulating material in an interstitial volume between two or more adjacent nanostructure electrodes. It can also be accomplished by providing a functionalizing substance, located on a selected region of the insulating material surface, which promotes attachment of the selected species particles to the functionalized surface, and measuring a selected electrical property such as electrical impedance, conductance, or capacitance. A time-varying electrical field E, having a root-mean-square intensity of E(sup 2) rms, with a non-zero gradient in a direction transverse to the liquid or fluid flow direction, is produced by a nanostructure electrode array with a very high-magnitude gradient near exposed electrode tips. A dielectrophoretic force causes the selected particles to accumulate near the electrode tips, if the medium and selected particles have substantially different dielectric constants. An insulating material surrounds most of the nanostructure electrodes, and a region of the insulating material surface is functionalized to promote attachment of the selected particle species to the surface. An electrical property value Z(meas) is measured at the functionalized surface, and is compared with a reference value Z(ref) to determine if the selected species particles are attached to the functionalized surface. Some advantages of this innovation are that an array of nanostructure electrodes can provide an electric field intensity gradient that is one or more orders of magnitude greater than the corresponding gradient provided by a conventional microelectrode arrangement, and that, as a result of the high-magnitude field intensity gradients, a nanostructure concentrator can trap particles from high-speed microfluidic flows. This is critical for applications where the entire analysis must be performed in a few minutes

Method of adhesion between an oxide layer and a metal layer

DOEpatents

Jennison, Dwight R.; Bogicevic, Alexander; Kelber, Jeffry A.; Chambers, Scott A.

2004-09-14

A method of controlling the wetting characteristics and increasing the adhesion between a metal and an oxide layer. By introducing a negatively-charged species to the surface of an oxide layer, layer-by-layer growth of metal deposited onto the oxide surface is promoted, increasing the adhesion strength of the metal-oxide interface. The negatively-charged species can either be deposited onto the oxide surface or a compound can be deposited that dissociates on, or reacts with, the surface to form the negatively-charged species. The deposited metal adatoms can thereby bond laterally to the negatively-charged species as well as vertically to the oxide surface as well as react with the negatively charged species, be oxidized, and incorporated on or into the surface of the oxide.

Archaeological Test Excavations. Phase II Testing at the Hagerman National Fish Hatchery, Hagerman Valley, Idaho,

DTIC Science & Technology

1981-02-01

horizons, a surface horizon or hori- zons not significantly darkened by humus , and absence of deep, wide cracks . . . the Aridisols have no "available...constituents or the frequencies of the various species present, as opposed to an area like the Hagerman locale which is characterized by a complex... species along with the Agropyron, stiff sagebrush (Artemisia rigida), threetip sagebrush (Artemisia tripartita) or low sagebrush (Artemisia arbuscula

On the Surface Formation of NH3 and HNCO in Dark Molecular Clouds - Searching for Wöhler Synthesis in the Interstellar Medium

NASA Astrophysics Data System (ADS)

Fedoseev, Gleb; Lamberts, Thanja; Linnartz, Harold; Ioppolo, Sergio; Zhao, Dongfeng

Despite its potential to reveal the link between the formation of simple species and more complex molecules (e.g., amino acids), the nitrogen chemistry of the interstellar medium (ISM) is still poorly understood. Ammonia (NH _{3}) is one of the few nitrogen-bearing species that have been observed in interstellar ices toward young stellar objects (YSOs) and quiescent molecular clouds. The aim of the present work is to experimentally investigate surface formation routes of NH _{3} and HNCO through non-energetic surface reactions in interstellar ice analogues under fully controlled laboratory conditions and at astrochemically relevant cryogenic temperatures. This study focuses on the formation of NH _{3} and HNCO in CO-rich (non-polar) interstellar ices that simulate the CO freeze-out stage in interstellar dark cloud regions, well before thermal and energetic processing start to become predominant. Our work confirms the surface formation of ammonia through the sequential addition of three hydrogen/deuterium atoms to a single nitrogen atom at low temperature. The H/D fractionation of the formed ammonia is also shown. Furthermore, we show the surface formation of solid HNCO through the interaction of CO molecules with NH radicals - one of the intermediates in the formation of solid NH _{3}. Finally, we discuss the implications of HNCO in astrobiology, as a possible starting point for the formation of more complex prebiotic species.

Dispersal of alien invasive species on anthropogenic litter from European mariculture areas.

PubMed

Rech, Sabine; Salmina, Simone; Borrell Pichs, Yaisel J; García-Vazquez, Eva

2018-06-01

The importance of mariculture areas for the dispersal of alien invasive species (AIS) on artificial floating items has recently been highlighted as a priority research need. Here we present the results of surveys in two important European shellfish culture areas that release rafting AIS, the Venetian lagoon and the Portuguese Algarve region. We found eight aquaculture-related non-native, invasive species attached to anthropogenic litter items mostly related to aquaculture: Amphibalanus amphitrite, Austrominius modestus, Balanus trigonus, Hesperibalanus fallax, Hydroides elegans, Hydroides sanctaecrucis, and Magallana angulata. These species are well-adapted to rafting on artificial surfaces and have a high potential to disperse via this vector. This is the first record of the notorious nuisance species H. sanctaecrucis both in the Mediterranean and Eastern Atlantic, as well as on floating litter. We also present the first records of M. angulata, H. sanctaecrucis, Sabellaria alveolata, Mytilus edulis and Chthamalus montagui on stranded anthropogenic litter. Copyright © 2018 Elsevier Ltd. All rights reserved.

Adsorption and diffusion of atomic oxygen and sulfur at pristine and doped Ni surfaces with implications for stress corrosion cracking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexandrov, Vitaly; Sushko, Maria L.; Schreiber, Daniel K.

A density-functional-theory modeling study of atomic oxygen/sulfur adsorption and diffusion at pristine and doped Ni(111) and (110) surfaces is presented. We find that oxygen and sulfur feature comparable adsorption energies over the same surface sites, however, the surface diffusion of sulfur is characterized by an activation barrier about one half that of oxygen. Calculations with different alloying elements at Ni surfaces show that Cr strongly enhances surface binding of both species in comparison to Al. These results in combination with previous modeling studies help explain the observed differences in selective grain boundary oxidation mechanisms of Ni-Cr and Ni-Al alloys.

Synthesis of flat sticky hydrophobic carbon diamond-like films using atmospheric pressure Ar/CH4 dielectric barrier discharge

NASA Astrophysics Data System (ADS)

Rincón, R.; Hendaoui, A.; de Matos, J.; Chaker, M.

2016-06-01

An Ar/CH4 atmospheric pressure dielectric barrier discharge (AP-DBD) was used to synthesize sticky hydrophobic diamond-like carbon (DLC) films on glass surface. The film is formed with plasma treatment duration shorter than 30 s, and water contact angles larger than 90° together with contact angle hysteresis larger than 10° can be achieved. According to Fourier transform infrared spectroscopy and atomic force microscopy analysis, hydrocarbon functional groups are created on the glass substrate, producing coatings with low surface energy (˜35 mJ m-2) with no modification of the surface roughness. To infer the plasma processes leading to the formation of low energy DLC surfaces, optical emission spectroscopy was used. From the results, a direct relationship between the CH species present in the plasma and the carbon concentration in the hydrophobic layer was found, which suggests that the CH species are the precursors of DLC film growth. Additionally, the plasma gas temperature was measured to be below 350 K which highlights the suitability of using AP-DBD to treat thermo-sensitive surfaces.

Spectral identification/elimination of molecular species in spacecraft glow

NASA Technical Reports Server (NTRS)

Green, B. D.; Marinelli, W. J.; Rawlins, W. T.

1985-01-01

Computer models of molecular electronic and vibrational emission intensities were developed. Known radiative emission rates (Einstein coefficients) permit the determination of relative excited state densities from spectral intensities. These codes were applied to the published spectra of glow above shuttle surface and to the Spacelab 1 results of Torr and Torr. The theoretical high-resolution spectra were convolved with the appropriate instrumental slit functions to allow accurate comparison with data. The published spacelab spectrum is complex but N2+ Meinel emission can be clearly identified in the ram spectrum. M2 First Positive emission does not correlate well with observed features, nor does the CN Red System. Spectral overlay comparisons are presented. The spectrum of glow above shuttle surfaces, in contrast to the ISO data, is not highly structured. Diatomic molecular emission was matched to the observed spectral shape. Source excitation mechanisms such as (oxygen atom)-(surface species) reaction product chemiluminescence, surface recombination, or resonance fluorescent re-emission will be discussed for each tentative assignment. These assignments are the necessary first analytical step toward mechanism identification. Different glow mechanisms will occur above surfaces under different orbital conditions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rincón, R., E-mail: rocio.rincon@emt.inrs.ca, E-mail: chaker@emt.inrs.ca; Matos, J. de; Chaker, M., E-mail: rocio.rincon@emt.inrs.ca, E-mail: chaker@emt.inrs.ca

An Ar/CH{sub 4} atmospheric pressure dielectric barrier discharge (AP-DBD) was used to synthesize sticky hydrophobic diamond-like carbon (DLC) films on glass surface. The film is formed with plasma treatment duration shorter than 30 s, and water contact angles larger than 90° together with contact angle hysteresis larger than 10° can be achieved. According to Fourier transform infrared spectroscopy and atomic force microscopy analysis, hydrocarbon functional groups are created on the glass substrate, producing coatings with low surface energy (∼35 mJ m{sup −2}) with no modification of the surface roughness. To infer the plasma processes leading to the formation of low energymore » DLC surfaces, optical emission spectroscopy was used. From the results, a direct relationship between the CH species present in the plasma and the carbon concentration in the hydrophobic layer was found, which suggests that the CH species are the precursors of DLC film growth. Additionally, the plasma gas temperature was measured to be below 350 K which highlights the suitability of using AP-DBD to treat thermo-sensitive surfaces.« less

Soot Formation in Laminar Premixed Ethylene/Air Flames at Atmospheric Pressure. Appendix G

NASA Technical Reports Server (NTRS)

Xu, F.; Sunderland, P. B.; Faeth, G. M.; Urban, D. L. (Technical Monitor)

2001-01-01

Soot formation was studied within laminar premixed ethylene/air flames (C/O ratios of 0.78-0.98) stabilized on a flat-flame burner operating at atmospheric pressure. Measurements included soot volume fractions by both laser extinction and gravimetric methods, temperatures by multiline emission, soot structure by thermophoretic sampling and transmission electron microscopy, major gas species concentrations by sampling and gas chromatography, concentrations of condensable hydrocarbons by gravimetric sampling. and velocities by laser velocimetry. These data were used to find soot surface growth rates and primary soot particle nucleation rates along the axes of the flames. Present measurements of soot surface growth rates were correlated successfully by predictions based on typical hydrogen-abstraction/carbon-addition (HACA) mechanisms of Frenklach and co-workers and Colket and Hall. These results suavest that reduced soot surface growth rates with increasing residence time seen in the present and other similar flames were mainly caused by reduced rates of surface activation due to reduced H atom concentrations as temperatures decrease as a result of radiative heat losses. Primary soot particle nucleation rates exhibited variations with temperature and acetylene concentrations that were similar to recent observations for diffusion flames; however, nucleation rates in the premixed flames were significantly lower than in, the diffusion flames for reasons that still must be explained. Finally, predictions of yields of major gas species based on mechanisms from both Frenklach and co-workers and Leung and Lindstedt were in good agreement with present measurements and suggest that H atom concentrations (relevant to HACA mechanisms) approximate estimates based on local thermodynamic equilibrium in the present flames.

Behavioral and brain asymmetries in primates: a preliminary evaluation of two evolutionary hypotheses.

PubMed

Hopkins, William D; Misiura, Maria; Pope, Sarah M; Latash, Elitaveta M

2015-11-01

Contrary to many historical views, recent evidence suggests that species-level behavioral and brain asymmetries are evident in nonhuman species. Here, we briefly present evidence of behavioral, perceptual, cognitive, functional, and neuroanatomical asymmetries in nonhuman primates. In addition, we describe two historical accounts of the evolutionary origins of hemispheric specialization and present data from nonhuman primates that address these specific theories. Specifically, we first discuss the evidence that genes play specific roles in determining left-right differences in anatomical and functional asymmetries in primates. We next consider and present data on the hypothesis that hemispheric specialization evolved as a by-product of increasing brain size relative to the surface area of the corpus callosum in different primate species. Last, we discuss some of the challenges in the study of hemispheric specialization in primates and offer some suggestions on how to advance the field. © 2015 New York Academy of Sciences.

12 years of Pluto surface's evolution investigated with radiative transfer modeling

NASA Astrophysics Data System (ADS)

Philippe, Sylvain; Schmitt, Bernard; Grundy, William; Protopapa, Silvia; Olkin, Cathy

2015-11-01

The evolution of Pluto’s surface through time, due to surface - atmosphere interactions, remains unknown. New Horizons will provide very high spatial resolution data of its surface state but only as a snapshot. Furthermore, this evolution during the last decades is supposed to be fast due to the recent passage of Pluto through its perihelion (1989). Ground based survey data over a long period of time are thus crucial to understand the long-term evolution of the dwarf planet surface.IRTF/SpeX reflectance spectra of Pluto have been acquired during 13 years (2001-2013) between 0.8-2.4 μm (Grundy et al., 2013; Grundy et al., 2014). This set of data present the opportunity to monitor possible changes of the surface in terms of geographical distribution and segregation between different chemical species that are known to be present at the surface in an icy state (N2, CH4 and CO, Owen et al., 1993, Douté et al., 1999). These variations are recorded through changes in the infrared absorption bands of the different ices. A study based on band criteria variation (Grundy et al., 2013) showed that CH4 absorption bands are increasing through time, whereas N2 and CO absorptions bands are decreasing (Grundy et al. 2014). However, quantitative interpretation of these data needs further investigation and detailed radiative transfer modeling.We used the bidirectional reflectance model of Douté & Schmitt (1998) to fit the IRTF/SpeX spectral data. This model takes into account a possible stratification of chemical species, a phenomenon that is likely to occur on Pluto where CH4 is supposed to accumulate on a sublimating molecular mixture of N2-CH4-CO (Douté et al., 1999). Different modelings take into account pure CH4 ice, a molecular mixture of N2-CH4-CO, tholins and water ice. We modeled the grand average spectra and then allowed the parameters to vary around the average values to model individual spectra and get quantitative variations of the different species.Preliminary results of these modelings will be presented in terms of longitudinal and temporal variations. This study could provide a useful precursor for the analysis of the spatially resolved New Horizon hyper spectral data acquired by the RALPH/Leisa instrument.

Distribution of olfactory epithelium in the primate nasal cavity: are microsmia and macrosmia valid morphological concepts?

PubMed

Smith, Timothy D; Bhatnagar, Kunwar P; Tuladhar, Praphul; Burrows, Annie M

2004-11-01

The terms "microsmatic" and "macrosmatic" are used to compare species with greater versus lesser olfactory capabilities, such as carnivores compared to certain primates. These categories have been morphologically defined based on the size of olfactory bulb and surface area of olfactory epithelium in the nasal fossa. The present study examines assumptions regarding the morphological relationship of bony elements to the olfactory mucosa, the utility of olfactory epithelial surface area as a comparative measurement, and the utility of the microsmatic concept. We examined the distribution of olfactory neuroepithelium (OE) across the anteroposterior length of the nasal fossa (from the first completely enclosed cross-section of the nasal fossa to the choanae) in the microsmatic marmoset (Callithrix jacchus) compared to four species of nocturnal strepsirrhines (Otolemur crassicaudatus, O. garnetti, Microcebus murinus, and Cheirogaleus medius). Adults of all species were examined and infant C. jacchus, O. crassicaudatus, M. murinus, and C. medius were also examined. All specimens were serially sectioned in the coronal plane and prepared for light microscopic study. Distribution of OE across all the turbinals, nasal septal surfaces, and accessory spaces of the nasal chamber was recorded for each specimen. The right nasal fossae of one adult C. jacchus and one neonatal M. murinus were also three-dimensionally reconstructed using Scion Image software to reveal OE distribution. Findings showed OE to be distributed relatively more anteriorly in adult C. jacchus compared to strepsirrhines. It was also distributed more anteriorly along the nasal septal walls and recesses in neonates than adults. Our findings also showed that OE surface area was not a reliable proxy for receptor neuron numbers due to differing OE thickness among species. Such results indicate that nasal cavity morphology must be carefully reconsidered regarding traditional functional roles (olfaction versus air conditioning) assigned to various nasal cavity structures. At present, the microsmatic concept itself lacks a basis in nasal chamber morphology, since OE may have varying patterns of distribution among different primates. (c) 2004 Wiley-Liss, Inc.

STM observation of the chemical reaction of atomic hydrogen on the N-adsorbed Cu(001) surface

NASA Astrophysics Data System (ADS)

Hattori, Takuma; Yamada, Masamichi; Komori, Fumio

2017-01-01

Chemical reaction of atomic hydrogen with the N-adsorbed Cu(001) surfaces was investigated at room temperature by scanning tunnel microscopy. At the low exposure of atomic hydrogen, it reacted with the N atoms and turned to be the NH species on the surface. The reaction rate is proportional to the amount of the unreacted N atoms. By increasing the exposure of atomic hydrogen from this condition, the amount of nitrogen species on the surface decreased. This is attributed to the formation of ammonia and its desorption from the surface. The NH species on the surface turn to NH3 through the surface NH2 species by atomic hydrogen. Coexistence of the clean Cu surface enhances the rate of ammonia formation owing to atomic hydrogen migrating on the clean surface.

Effect of Pb2+ ions on ilmenite flotation and adsorption of benzohydroxamic acid as a collector

NASA Astrophysics Data System (ADS)

Xu, Longhua; Tian, Jia; Wu, Houqin; Lu, Zhongyuan; Yang, Yaohui; Sun, Wei; Hu, Yuehua

2017-12-01

The effects of Pb2+ ions on ilmenite flotation and adsorption of benzohydroxamic acid (BHA) as a collector were investigated using microflotation tests, zeta potential measurements, adsorption analysis, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The microflotation results indicate that the addition of Pb2+ significantly improves the recovery of ilmenite using BHA as a collector. A maximum recovery of 88.46% is obtained at pH 8.12 in the presence of Pb2+; a maximum recovery of 45% is obtained at the same pH using BHA alone. At pHs below 8.0, lead nitrate are mainly present in the solution as Pb2+ and PbOH+, while at pHs above 8.0, the predominant components are Pb(OH)2(s) and Pb(OH)3-. The adsorption of these lead species influences the zeta potential of ilmenite and the number of activated sites on the ilmenite surface. FTIR and XPS analyses reveal that lead species and BHA react with the metal sites on the ilmenite surface. The lead species in solution are either adsorbed onto the ilmenite surface, which increases the surface activity of ilmenite, or react with BHA in solution to form complexes of lead and BHA.

An evaluation of trees and shrubs for planting surface-mine spoils

Treesearch

William T. Plass

1975-01-01

Fifty-five tree and shrub species were evaluated on two surface-mine sites in eastern Kentucky. After 4 years' growth, comparison of survival and growth was used to identify the promising species for planting on acid surface-mine spoils. Three species of birch and three Eleagnus species survived and grew well on a range of sites. Noncommercial...

High Resolution Habitat Suitability Modelling For Restricted-Range Hawaiian Alpine Arthropod Species

NASA Astrophysics Data System (ADS)

Stephenson, N. M.

2016-12-01

Mapping potentially suitable habitat is critical for effective species conservation and management but can be challenging in areas exhibiting complex heterogeneity. An approach that combines non-intrusive spatial data collection techniques and field data can lead to a better understanding of landscapes and species distributions. Nysius wekiuicola, commonly known as the wēkiu bug, is the most studied arthropod species endemic to the Maunakea summit in Hawai`i, yet details about its geographic distribution and habitat use remain poorly understood. To predict the geographic distribution of N. wekiuicola, MaxEnt habitat suitability models were generated from a diverse set of input variables, including fifteen years of species occurrence data, high resolution digital elevation models, surface mineralogy maps derived from hyperspectral remote sensing, and climate data. Model results indicate that elevation (78.2 percent), and the presence of nanocrystalline hematite surface minerals (13.7 percent) had the highest influence, with lesser contributions from aspect, slope, and other surface mineral classes. Climatic variables were not included in the final analysis due to auto-correlation and coarse spatial resolution. Biotic factors relating to predation and competition also likely dictate wēkiu bug capture patterns and influence our results. The wēkiu bug range and habitat suitability models generated as a result of this study will be directly incorporated into management and restoration goals for the summit region and can also be adapted for other arthropod species present, leading to a more holistic understanding of metacommunity dynamics. Key words: Microhabitat, Structure from Motion, Lidar, MaxEnt, Habitat Suitability

Platinized tin oxide catalysts for CO2 lasers: Effects of pretreatment

NASA Technical Reports Server (NTRS)

Gardner, Steven D.; Hoflund, Gar B.; Schryer, David R.; Upchurch, Billy T.

1990-01-01

Platinized tin oxide surfaces used for low-temperature CO oxidation in CO2 lasers have been characterized before and after reduction in CO at 125 and 250 C using ion scattering spectroscopy (ISS) and X ray photoelectron spectroscopy (XPS). XPS indicates that the Pt is present initially as PtO2. Reduction at 125 C converts the PtO2 to Pt(OH)2 while reduction at 250 C converts the PtO2 to metallic Pt. ISS shows that the Pt in the outermost atomic layer of the catalyst is mostly covered by substrate species during the 250 C reduction. Both the ISS and XPS results are consistent with Pt/Sn alloy formation. The surface dehydration and migration of substrate species over surface Pt and Sn appear to explain why a CO pretreatment at 250 C produces inferior CO oxidation activities compared to a 125 C pretreatment.

Platinized tin oxide catalysts for CO2 lasers - Effects of pretreatment

NASA Technical Reports Server (NTRS)

Gardner, Steven D.; Hoflund, Gar B.; Schryer, David R.; Upchurch, Billy T.

1989-01-01

Platinized tin oxide surfaces used for low-temperature CO oxidation in CO2 lasers have been characterized before and after reduction in CO at 125 and 250 C using ion scattering spectroscopy (ISS) and X-ray photoelectron spectroscopy (XPS). XPS indicates that the Pt is present initially as Pto2. Reduction at 125 C converts the PtO2 to Pt(OH)2 while reduction at 250 C converts the PtO2 to metallic Pt. ISS shows that the Pt in the outermost atomic layer of the catalyst is mostly covered by substrate species during the 250 C reduction. Both the ISS and XPS results are consistent with Pt/Sn alloy formation. The surface dehydration and migration of substrate species over surface Pt and Sn appear to explain why a CO pretreatment at 250 C produces inferior CO oxidation activities compared to a 125 C pretreatment.

Atomic scale friction of molecular adsorbates during diffusion.

PubMed

Lechner, B A J; de Wijn, A S; Hedgeland, H; Jardine, A P; Hinch, B J; Allison, W; Ellis, J

2013-05-21

Experimental observations suggest that molecular adsorbates exhibit a larger friction coefficient than atomic species of comparable mass, yet the origin of this increased friction is not well understood. We present a study of the microscopic origins of friction experienced by molecular adsorbates during surface diffusion. Helium spin-echo measurements of a range of five-membered aromatic molecules, cyclopentadienyl, pyrrole, and thiophene, on a copper(111) surface are compared with molecular dynamics simulations of the respective systems. The adsorbates have different chemical interactions with the surface and differ in bonding geometry, yet the measurements show that the friction is greater than 2 ps(-1) for all these molecules. We demonstrate that the internal and external degrees of freedom of these adsorbate species are a key factor in the underlying microscopic processes and identify the rotation modes as the ones contributing most to the total measured friction coefficient.

Determination of total arsenic and arsenic species in drinking water, surface water, wastewater, and snow from Wielkopolska, Kujawy-Pomerania, and Lower Silesia provinces, Poland.

PubMed

Komorowicz, Izabela; Barałkiewicz, Danuta

2016-09-01

Arsenic is a ubiquitous element which may be found in surface water, groundwater, and drinking water. In higher concentrations, this element is considered genotoxic and carcinogenic; thus, its level must be strictly controlled. We investigated the concentration of total arsenic and arsenic species: As(III), As(V), MMA, DMA, and AsB in drinking water, surface water, wastewater, and snow collected from the provinces of Wielkopolska, Kujawy-Pomerania, and Lower Silesia (Poland). The total arsenic was analyzed by inductively coupled plasma mass spectrometry (ICP-MS), and arsenic species were analyzed with use of high-performance liquid chromatography inductively coupled plasma mass spectrometry (HPLC/ICP-MS). Obtained results revealed that maximum total arsenic concentration determined in drinking water samples was equal to 1.01 μg L(-1). The highest concentration of total arsenic in surface water, equal to 3778 μg L(-1) was determined in Trująca Stream situated in the area affected by geogenic arsenic contamination. Total arsenic concentration in wastewater samples was comparable to those determined in drinking water samples. However, significantly higher arsenic concentration, equal to 83.1 ± 5.9 μg L(-1), was found in a snow sample collected in Legnica. As(V) was present in all of the investigated samples, and in most of them, it was the sole species observed. However, in snow sample collected in Legnica, more than 97 % of the determined concentration, amounting to 81 ± 11 μg L(-1), was in the form of As(III), the most toxic arsenic species.

Study of surfaces using near infrared optical fiber spectrometry

NASA Technical Reports Server (NTRS)

Workman, G. L.; Arendale, W. A.; Hughes, C.

1995-01-01

The measurement and control of cleanliness for critical surfaces during manufacturing and in service provides a unique challenge for fulfillment of environmentally benign operations. Of particular interest has been work performed in maintaining quality in the production of bondline surfaces in propulsion systems and the identification of possible contaminants. This work requires an in-depth study of the possible sources of contamination, methodologies to identify contaminants, discrimination between contaminants and chemical species caused by environment, and the effect of particular contaminants on the bondline integrity of the critical surfaces. This presentation will provide an introduction to the use of optical fiber spectrometry in a nondestructive measurement system for process monitoring and how it can be used to help clarify issues concerning surface chemistry. Correlation of the Near Infrared (NIR) spectroscopic results with Optical Stimulated Electron Emission (OSEE) and ellipsometry will also be presented.

Red-shifting and blue-shifting OH groups on metal oxide surfaces - towards a unified picture.

PubMed

Kebede, Getachew G; Mitev, Pavlin D; Briels, Wim J; Hermansson, Kersti

2018-05-09

We analyse the OH vibrational signatures of 56 structurally unique water molecules and 34 structurally unique hydroxide ions in thin water films on MgO(001) and CaO(001), using DFT-generated anharmonic potential energy surfaces. We find that the OH stretching frequencies of intact water molecules on the surface are always downshifted with respect to the gas-phase species while the OH- groups are either upshifted or downshifted. Despite these differences, the main characteristics of the frequency shifts for all three types of surface OH groups (OHw, OsH and OHf) can be accounted for by one unified expression involving the in situ electric field from the surrounding environment, and the gas-phase molecular properties of the vibrating species (H2O or OH-). The origin behind the different red- and blueshift behaviour can be traced back to the fact that the molecular dipole moment of a gas-phase water molecule increases when an OH bond is stretched, but the opposite is true for the hydroxide ion. We propose that familiarity with the relations presented here will help surface scientists in the interpretation of vibrational OH spectra for thin water films on ionic crystal surfaces.

Saturn's satellites: Potential for organic chemistry

NASA Astrophysics Data System (ADS)

Delitsky, M. L.; Lane, A. L.; Henry-Riyad, H.; Tidwell, T. T.

2003-05-01

The surfaces of the Saturnian satellites are subjected to irradiation from solar wind ions, photons, and magnetospheric ions and electrons. This bombardment will transform the chemical nature of the surfaces. At present, only water ice has been detected on their surfaces. Further studies by the Cassini spacecraft may reveal other molecules. If CO2 ice is found there, a whole panoply of new species may be detected. As nitrogen ions in the magnetosphere are thought to be an important species bombarding the satellites, Delitsky and Lane (2002) outlined the nitrogen oxides chemistry that may result from implantation of N+ into the water ice surfaces. Sittler et al (2002) showed that N+ ions originating from Titan will be enriched in the magnetospheric ion population as they move inwards towards Saturn, making the nitrogen oxides chemistry more likely. If CO2 is present, a complicated C-H-N-O chemistry may result from deposition of the N+ into a H2O/CO2 mixed ice, including nitriles, isocyanates, polymers, and amino acids. The combination of H2O/CO2 upon irradiation may also yield a complex mixture of hydrocarbons, esters, alcohols, organic acids and ketones. Possible chemical pathways and computations of their energetics will be presented. -Ref:- 1. Delitsky and Lane, Saturn's inner satellites: Ice chemistry and magnetosphere effects, JGR (Planets), Nov 2002, 3-1;; 2. Sittler et al., Energetic nitrogen ions within the inner magnetosphere of Saturn, Fall AGU meeting, Dec 2002, abstracts, pg F858, P21B-0379

Chalcopyrite dissolution: Scanning photoelectron microscopy examination of the evolution of sulfur species with and without added iron or pyrite

NASA Astrophysics Data System (ADS)

Li, Yubiao; Qian, Gujie; Brown, Paul L.; Gerson, Andrea R.

2017-09-01

Dissolution and oxidation of sulfide minerals play key roles in both acid and metalliferous rock drainage and supergene enrichment. Surface speciation heterogeneity, critical to understanding mechanisms of mineral sulfide dissolution, has to date largely not been considered. To this end synchrotron scanning photoelectron microscopy (SPEM) was employed to examine freshly fractured and partially dissolved chalcopyrite (CuFeS2) surfaces (pH 1.0 HClO4 solution, redox potential 650 mV relative to a standard hydrogen electrode, 75 °C). S2- (bulk), S22- and Sn2- were found to be present on all samples at varying concentrations. Oxidation was observed to take place heterogeneously at the sub-micron scale. As compared to chalcopyrite partially dissolved for 5 days, extended dissolution to 10 days did not show appreciably enhanced oxidation of surface species; however surface roughness increased markedly due to the growth/overlap of oxidised sulfur species. On addition of 4 mM iron both S0 and SO42- were observed but not SO32-, indicating that the greater Fe3+ activity/concentration promotes heterogeneous sulfur oxidation. On contact of pyrite (FeS2) with chalcopyrite, significantly greater chalcopyrite surface oxidation was observed than for the other systems examined, with S0, SO32- and SO42- being identified heterogeneously across the surface. It is proposed that chalcopyrite oxidative dissolution is enhanced by increasing its cathodic area, e.g. contacting with pyrite, while increased Fe3+ activity/concentration also contributes to increased dissolution rates. The high degree of surface heterogeneity of these surface products indicates that these surfaces are not passivated by their formation. These results suggest that chalcopyrite dissolution will be accelerated when in contact with pyrite at solution redox potential intermediate between the rest potentials of chalcopyrite and pyrite (560 mV and 660 mV, respectively) and/or iron rich acidic waters with resulting enhanced formation of secondary sulfur containing species and release of copper and iron. This in turn suggests accelerated supergene formation and enhanced metalliferous drainage under these conditions.

Effects of hydration and oxygen vacancy on CO2 adsorption and activation on beta-Ga2O3(100).

PubMed

Pan, Yun-xiang; Liu, Chang-jun; Mei, Donghai; Ge, Qingfeng

2010-04-20

The effects of hydration and oxygen vacancy on CO(2) adsorption on the beta-Ga(2)O(3)(100) surface have been studied using density functional theory slab calculations. Adsorbed CO(2) is activated on the dry perfect beta-Ga(2)O(3)(100) surface, resulting in a carbonate species. This adsorption is slightly endothermic, with an adsorption energy of 0.07 eV. Water is preferably adsorbed molecularly on the dry perfect beta-Ga(2)O(3)(100) surface with an adsorption energy of -0.56 eV, producing a hydrated perfect beta-Ga(2)O(3)(100) surface. Adsorption of CO(2) on the hydrated surface as a carbonate species is also endothermic, with an adsorption energy of 0.14 eV, indicating a slightly repulsive interaction when H(2)O and CO(2) are coadsorbed. The carbonate species on the hydrated perfect surface can be protonated by the coadsorbed H(2)O to a bicarbonate species, making the CO(2) adsorption exothermic, with an adsorption energy of -0.13 eV. The effect of defects on CO(2) adsorption and activation has been examined by creating an oxygen vacancy on the dry beta-Ga(2)O(3)(100) surface. The formation of an oxygen vacancy is endothermic, by 0.34 eV, with respect to a free O(2) molecule in the gas phase. Presence of the oxygen vacancy promoted the adsorption and activation of CO(2). In the most stable CO(2) adsorption configuration on the dry defective beta-Ga(2)O(3)(100) surface with an oxygen vacancy, one of the oxygen atoms of the adsorbed CO(2) occupies the oxygen vacancy site, and the CO(2) adsorption energy is -0.31 eV. Water favors dissociative adsorption at the oxygen vacancy site on the defective surface. This process is spontaneous, with a reaction energy of -0.62 eV. These results indicate that, when water and CO(2) are present in the adsorption system simultaneously, water will compete with CO(2) for the oxygen vacancy sites and impact CO(2) adsorption and conversion negatively.

Effect of horizontal resolution on meteorology and air-quality prediction with a regional scale model

NASA Astrophysics Data System (ADS)

Varghese, Saji; Langmann, Baerbel; Ceburnis, Darius; O'Dowd, Colin D.

2011-08-01

Horizontal resolution sensitivity can significantly contribute to the uncertainty in predictions of meteorology and air-quality from a regional climate model. In the study presented here, a state-of-the-art regional scale atmospheric climate-chemistry-aerosol model REMOTE is used to understand the influence of spatial model resolutions of 1.0°, 0.5° and 0.25° on predicted meteorological and aerosol parameters for June 2003 for the European domain comprising North-east Atlantic and Western Europe. Model precipitation appears to improve with resolution while wind speed has shown best results for 0.25° resolution for most of the stations compared with ECAD data. Low root mean square error and spatial bias for surface pressure, precipitation and surface temperature show that the model is very reliable. Spatial and temporal variation in black carbon, primary organic carbon, sea-salt and sulphate concentrations and their burden are presented. In most cases, chemical species concentrations at the surface show no particular trend or improvement with increase in resolution. There has been a pronounced influence of horizontal resolution on the vertical distribution pattern of some aerosol species. Some of these effects are due to the improvement in topographical details, flow characteristics and associated vertical and horizontal dynamic processes. The different sink processes have contributed very differently to the various aerosol species in terms of deposition (wet and dry) and sedimentation which are strongly linked to the meteorological processes. Overall, considering the performance of meteorological parameters and chemical species concentrations, a horizontal model resolution of 0.5° is suggested to achieve reasonable results within the limitations of this model.

Temperature profile of graphite surface burning in a stream of oxygen

NASA Technical Reports Server (NTRS)

Kisch, D.

1978-01-01

Using methods for the objective measurement of the spectrum line reversal temperature in burning gases, the temperature profile at a graphite surface burning in a stream of oxygen was measured. From the behavior of the reversal temperature, it follows that particles in long-lived, high-energy states are present in the burning gas, and these bring about an overexcitation of the atomic species emitting the reversal line. Qualitative measurements show that a temperature maximum occurs at the expected distance of 1-2 mm from the graphite surface.

Some interesting aspects of physisorption stay-time measurements obtained using molecular-beam techniques. [on Ni surface

NASA Technical Reports Server (NTRS)

Wilmoth, R. G.; Fisher, S. S.

1974-01-01

Stay-time distributions have been obtained for Xe physisorbing on polycrystalline nickel as a function of the target temperature using a pulsed molecular-beam technique. Some interesting effects due to ion bombardment of the surface using He, Ar, and Xe ions are presented. Measured detector signal shapes are found to deviate from those predicted for first-order desorption with velocities corresponding to Maxwellian effusion at the surface temperature. Evidence is found for interaction between beam pulse adsorption and steady-state adsorption of beam species background atoms.

Theoretical modeling to study the impact of different oxidizers (etchants) on the plasma-assisted catalytic carbon nanofiber growth

NASA Astrophysics Data System (ADS)

Gupta, Ravi; Sharma, Suresh C.

2017-07-01

An analytical model based on the various surface deposition processes and plasma sheath kinetics of the plasma species (electrons, positively charged ions, radicals, and neutrals) has been developed to investigate the effects of different plasmas (different etchants) on the catalyzed plasma aided growth of carbon nanofibers (CNFs). In particular, the model accounts the poisoning of the catalyst nanoparticle, i.e., the formation of the amorphous carbon layer on the catalyst active surface due to the continuous dissociation of incoming hydrocarbon species from the plasma. It is observed that oxidizers (H2O and O2) in the typical hydrocarbon/hydrogen (C2H2 + H2) plasma act as the dominant etchants and remove the amorphous carbon layer from the catalyst surface and, thus, preserve and enhance the catalyst activity. However, the growth rate of CNFs is much higher when O2 is added as an etchant in the reactive plasma as compared to H2O. This is due to the dual role played by the oxygen, i.e., (i) removal of amorphous carbon from the catalyst active surface, (ii) removal of hydrogen radicals that interact with the carbon species generated on the catalyst surface and suppress their diffusion through the catalyst nanoparticles. The CNF grows much longer in the presence of O2, therefore, etching of CNF tip and deformation of catalyst nanoparticle is the maximum, and hence, the CNF tip diameter is least. Moreover, in the present investigation, we also found that the relative concentrations of H2O or O2 species in the reactive plasma have significant effects on the CNF growth. Our theoretical results are in good agreement with the experimental observations.

Quantitative MAS NMR characterization of the LiMn(1/2)Ni(1/2)O(2) electrode/electrolyte interphase.

PubMed

Cuisinier, M; Martin, J F; Moreau, P; Epicier, T; Kanno, R; Guyomard, D; Dupré, N

2012-04-01

The conditions in which degradation processes at the positive electrode/electrolyte interface occur are still incompletely understood and traditional surface analytical techniques struggle to characterize and depict accurately interfacial films. In the present work, information on the growth and evolution of the interphases upon storage and cycling as well as their electrochemical consequences are gathered in the case of LiNi(1/2)Mn(1/2)O(2) with commonly used LiPF(6) (1M in EC/DMC) electrolyte. The use of (7)Li, (19)F and (31)P MAS NMR, made quantitative through the implementation of empirical calibration, is combined with transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS) to probe the elements involved in surface species and to unravel the inhomogenous architecture of the interphase. At room temperature, contact with the electrolyte leads to a covering of the oxide surface first by LiF and lithiated organic species are found on the outer part of the interphase. At 55°C, not only the interphase proceeds in further covering of the surface but also thickens resulting in an increase of 240% of lithiated species and the presence of -POF(2) fluorophosphates. The composition gradient within the interphase depth is also strongly affected by the temperature. In agreement with the electrochemical performance, quantitative NMR surface analyses show that the use of LiBOB-modified electrolyte results in a Li-enriched interphase, intrinsically less resistive than the standard LiPF(6)-based interphase, comprised of a mixture of resistive LiF with non lithiated species. Copyright © 2011 Elsevier Inc. All rights reserved.

A new recipe for preparing oxidized TiO2(1 1 0) surfaces: An STM study

NASA Astrophysics Data System (ADS)

Hansen, Jonas Ø.; Matthiesen, Jesper; Lira, Estephania; Lammich, Lutz; Wendt, Stefan

2017-12-01

Using high-resolution scanning tunneling microscopy (STM), we have studied the oxidation of rutile TiO2(1 1 0)-(1 × 1) surfaces with Had species at room temperature. We followed the evolution of various stable species as function of the O2 exposure, and the nature of the ultimately dominating species in the Ti troughs is described. When O2 saturation was accomplished using a glass-capillary array doser, we found that on-top O (Oot) adatoms are the predominant surface species. In contrast, when O2 was supplied via backfilling of the chamber the predominant surface species are tentatively assigned to terminal OH groups. We argue that unintended reactions with the chamber walls have a strong influence on the formed surface species, explaining scattered results in the literature. On the basis of our STM data we propose an alternative, easy way of preparing oxidized TiO2(1 1 0) surfaces with Oot adatoms (o-TiO2). It is certain that o-TiO2(1 1 0) surfaces prepared according to this recipe do not have any residual surface O vacancies. This contradicts the situation when oxidizing reduced TiO2(1 1 0) surfaces with O vacancies, where some O vacancies persist.

Gas-phase chemistry in dense interstellar clouds including grain surface molecular depletion and desorption

NASA Technical Reports Server (NTRS)

Bergin, E. A.; Langer, W. D.; Goldsmith, P. F.

1995-01-01

We present time-dependent models of the chemical evolution of molecular clouds which include depletion of atoms and molecules onto grain surfaces and desorption, as well as gas-phase interactions. We have included three mechanisms to remove species from the grain mantles: thermal evaporation, cosmic-ray-induced heating, and photodesorption. A wide range of parameter space has been explored to examine the abundance of species present both on the grain mantles and in the gas phase as a function of both position in the cloud (visual extinction) and of evolutionary state (time). The dominant mechanism that removes molecules from the grain mantles is cosmic-ray desorption. At times greater than the depletion timescale, the abundances of some simple species agree with abundances observed in the cold dark cloud TMC-1. Even though cosmic-ray desorption preserves the gas-phase chemistry at late times, molecules do show significant depletions from the gas phase. Examination of the dependence of depletion as a function of density shows that when the density increases from 10(exp 3)/cc to 10(exp 5)/cc several species including HCO(+), HCN, and CN show gas-phase abundance reductions of over an order of magnitude. The CO: H2O ratio in the grain mantles for our standard model is on the order of 10:1, in reasonable agreement with observations of nonpolar CO ice features in rho Ophiuchus and Serpens. We have also examined the interdependence of CO depletion with the space density of molecular hydrogen and binding energy to the grain surface. We find that the observed depletion of CO in Taurus in inconsistent with CO bonding in an H2O rich mantle, in agreement with observations. We suggest that if interstellar grains consist of an outer layer of CO ice, then the binding energies for many species to the grain mantle may be lower than commonly used, and a significant portion of molecular material may be maintained in the gas phase.

Experimental Investigation of Neutral Species from Micrometeoroid Bombardment

NASA Astrophysics Data System (ADS)

Collette, A.; Sternovsky, Z.; Rocha, J. R.; Munsat, T. L.; Horanyi, M.

2014-12-01

Surface-boundary exospheres exist in a balance between source and loss processes. An important area of uncertainty, highlighted by the MESSENGER observations of Mg and Ca at Mercury, and the recently concluded LADEE observations at the Moon, is the role of micrometeoroid bombardment as a source process for liberating surface species. Unlike sputtering or photon stimulated desorption processes, the physics of micrometeoroid impacts are still poorly understood; in particular, no comprehensive model exists to predict partitioning of impact products between ejecta fragments, charged particles, and neutrals. We present initial experiments at the IMPACT dust accelerator facility (University of Colorado Boulder) aimed at directly measuring the fraction of neutral species liberated in micrometeoroid impacts. Simulated micrometeoroids (micron- and submicron-sized iron spheres) are fired at targets containing refractory elements, including fused silica (SiO2), sapphire (Al2O3), and magnesium fluoride (MgF2). Total quantities of specific impact-generated neutral species are measured using a mass spectrometer, as a function of impactor speed and mass, and compared with well-established scaling laws for charged particle production.

Design and analysis of surface plasmon resonance (SPR) sensor to check the quality of food from adulteration

NASA Astrophysics Data System (ADS)

Kumar, Manish; Raghuwanshi, Sanjeev Kumar

2018-02-01

In recent years, food safety issues caused by contamination of chemical substances or microbial species have raised a major area of concern to mankind. The conventional chromatography-based methods for detection of chemical are based on human-observation and slow for real-time monitoring. The surface plasmon resonance (SPR) sensors offers the capability of detection of very low concentrations of adulterated chemical and biological agents for real-time by monitoring. Thus, adulterant agent in food gives change in refractive index of pure food result in corresponding phase change. These changes can be detected at the output and can be related to the concentration of the chemical species present at the point.

Intracellular processing of epidermal growth factor. I. Acidification of 125I-epidermal growth factor in intracellular organelles.

PubMed

Matrisian, L M; Planck, S R; Magun, B E

1984-03-10

We previously reported that 125I-labeled epidermal growth factor is processed intracellularly to acidic macromolecules in Rat-1 fibroblasts. The present study defines the precursor-product relationship and localization of the processing steps to subcellular organelles by the use of a single isoelectric species of 125I-epidermal growth factor and Percoll gradient fractionation. The native pI 4.55 125I-epidermal growth factor was rapidly processed to a pI 4.2 species on or near the cell surface and in organelles corresponding to clathrin-coated vesicles, Golgi, and endoplasmic reticulum. This species was then processed to a pI 4.35 species in similar organelles. The pI 4.2 and 4.35 species were converted to a pI 4.0 species in dense, lysosome-like organelles. This species was ultimately degraded and exocytosed from the cell as low molecular weight products.

The Everglades Depth Estimation Network (EDEN) surface-water model, version 2

USGS Publications Warehouse

Telis, Pamela A.; Xie, Zhixiao; Liu, Zhongwei; Li, Yingru; Conrads, Paul

2015-01-01

Three applications of the EDEN-modeled water surfaces and other EDEN datasets are presented in the report to show how scientists and resource managers are using EDEN datasets to analyze biological and ecological responses to hydrologic changes in the Everglades. The biological responses of two important Everglades species, alligators and wading birds, to changes in hydrology are described. The effects of hydrology on fire dynamics in the Everglades are also discussed.

Atomic Oxygen Effects

NASA Technical Reports Server (NTRS)

Miller, Sharon K. R.

2014-01-01

Atomic oxygen, which is the most predominant species in low Earth orbit, is highly reactive and can break chemical bonds on the surface of a wide variety of materials leading to volatilization or surface oxidation which can result in failure of spacecraft materials and components. This presentation will give an overview of how atomic oxygen reacts with spacecraft materials, results of space exposure testing of a variety of materials, and examples of failures caused by atomic oxygen.

Surface modification of malachite with ethanediamine and its effect on sulfidization flotation

NASA Astrophysics Data System (ADS)

Feng, Qicheng; Zhao, Wenjuan; Wen, Shuming

2018-04-01

Ethanediamine was used to modify the mineral surface of malachite to improve its sulfidization and flotation behavior. The activation mechanism was investigated by adsorption experiments, X-ray photoelectron spectroscopy (XPS) analysis, and zeta potential measurements. Microflotation experiments showed that the flotation recovery of malachite was enhanced after the pretreatment of the mineral particles with ethanediamine prior to the addition of Na2S. Adsorption tests revealed that numerous sulfide ion species in the pulp solution were transferred onto the mineral surface through the formation of more copper sulfide species. This finding was confirmed by the results of the XPS measurements. Ethanediamine modification not only increased the contents of copper sulfide species on the malachite surface but also enhanced the reactivity of the sulfidization products. During sulfidization, Cu(II) species on the mineral surface were reduced into Cu(I) species, and the percentages of S22- and Sn2- relative to the total S increased after modification, resulting in increased surface hydrophobicity. The results of zeta potential measurements showed that the ethanediamine-modified mineral surface adsorbed with more sulfide ion species was advantageous to the attachment of xanthate species, thereby improving malachite floatability. The proposed ethanediamine modification followed by sulfidization xanthate flotation exhibits potential for industrial application.

Penicillium salamii, a new species occurring during seasoning of dry-cured meat.

PubMed

Perrone, Giancarlo; Samson, Robert A; Frisvad, Jens C; Susca, Antonia; Gunde-Cimerman, Nina; Epifani, Filomena; Houbraken, Jos

2015-01-16

Fungi have an important role in the production of dry-cured meat products, especially during the seasoning period. In general, both industrially and handmade salami are quickly colonized by a composite mycobiota during seasoning, often with a strong predominance of Penicillium species. These species are involved in the improvement of the characteristics and taste, and in the prevention of the growth of pathogenic, toxigenic or spoilage fungi. During the survey of fungal species occurring on the salami surface and in the air of the seasoning and storage areas of a salami plant (Calabria, Italy), two Penicillium species were predominantly present. One species was identified as Penicillium nalgiovense, and the other was related to, but distinct from, Penicillium olsonii. Further molecular and biochemical analyses showed that this strain has high homology with the not yet described species named "Penicillium milanense" isolated in Denmark and Slovenia on cured meats. The taxonomic position of these strains in Penicillium was investigated using calmodulin, β tubulin and ITS sequences, phenotypic characters and extrolite patterns, and resulted in the discovery of a new Penicillium species, described here as P. salamii. A literature search showed that this species occurs on (cured) meat products worldwide. In our study, P. salamii predominated the salami and capocollo surface in levels similar to the commonly known starter culture P. nalgiovense, irrespective of the room or age of seasoning. Preliminary inoculation trials with P. salamii showed that it was able to colonize salami during seasoning, indicating that this species could be used as a fungal starter for dry-cured meat. Copyright © 2014. Published by Elsevier B.V.

FTIR study of methanol decomposition on gold catalyst for fuel cells

NASA Astrophysics Data System (ADS)

Boccuzzi, F.; Chiorino, A.; Manzoli, M.

The interaction of methanol (m), methanol-water (mw) and methanol-water-oxygen (mwo) on Au/TiO 2 catalyst has been investigated by in situ infrared spectroscopy (FTIR) and quadrupole mass spectrometry (QMS) at different temperatures. The aim of the work is to elucidate the nature and the abundance of the surface intermediates formed in different experimental conditions and to understand the mechanisms of methanol decomposition, of steam reforming and of combined reforming reactions. FTIR spectra run at room temperature in the different reaction mixtures show that differently coordinated methoxy species, that is on top species adsorbed on oxygen vacancy sites, on top species on uncoordinated Ti 4+ sites and bridged species on two Ti 4+ ions, are produced in all the mixtures. Quite strong formaldehyde and formate species adsorbed on gold are produced already at 403 K only in the combined reforming reaction mixture. At 473 K, on top species on uncoordinated Ti 4+ sites and methoxy species adsorbed on oxygen vacancy sites reduce their intensity and, at the same time, some formate species adsorbed on the support are produced in the steam reforming and combined reforming mixtures. At 523 K, on both methanol and methanol-water reaction mixtures, no more definite surface species are evidenced by FTIR on the catalysts, while in the methanol-water-oxygen mixture some residual methoxy and formate species are still present. Moreover, methanol is no more detected by QMS in the gas phase. A role of oxygen adsorbed on gold particles near oxygen vacancies of the support in the oxidative dehydrogenation of methanol is proposed.

Ti, Al and N adatom adsorption and diffusion on rocksalt cubic AlN (001) and (011) surfaces: Ab initio calculations

NASA Astrophysics Data System (ADS)

Mastail, C.; David, M.; Nita, F.; Michel, A.; Abadias, G.

2017-11-01

We use ab initio calculations to determine the preferred nucleation sites and migration pathways of Ti, Al and N adatoms on cubic NaCl-structure (B1) AlN surfaces, primary inputs towards a further thin film growth modelling of the TiAlN alloy system. The potential energy landscape is mapped out for both metallic species and nitrogen adatoms for two different AlN surface orientations, (001) and (110), using density functional theory. For all species, the adsorption energies on AlN(011) surface are larger than on AlN(001) surface. Ti and Al adatom adsorption energy landscapes determined at 0 K by ab initio show similar features, with stable binding sites being located in, or near, epitaxial surface positions, with Ti showing a stronger binding compared to Al. In direct contrast, N adatoms (Nad) adsorb preferentially close to N surface atoms (Nsurf), thus forming strong N2-molecule-like bonds on both AlN(001) and (011). Similar to N2 desorption mechanisms reported for other cubic transition metal nitride surfaces, in the present work we investigate Nad/Nsurf desorption on AlN(011) using a drag calculation method. We show that this process leaves a Nsurf vacancy accompanied with a spontaneous surface reconstruction, highlighting faceting formation during growth.

Polyphasic analysis of an Azoarcus-Leptothrix-dominated bacterial biofilm developed on stainless steel surface in a gasoline-contaminated hypoxic groundwater.

PubMed

Benedek, Tibor; Táncsics, András; Szabó, István; Farkas, Milán; Szoboszlay, Sándor; Fábián, Krisztina; Maróti, Gergely; Kriszt, Balázs

2016-05-01

Pump and treat systems are widely used for hydrocarbon-contaminated groundwater remediation. Although biofouling (formation of clogging biofilms on pump surfaces) is a common problem in these systems, scarce information is available regarding the phylogenetic and functional complexity of such biofilms. Extensive information about the taxa and species as well as metabolic potential of a bacterial biofilm developed on the stainless steel surface of a pump submerged in a gasoline-contaminated hypoxic groundwater is presented. Results shed light on a complex network of interconnected hydrocarbon-degrading chemoorganotrophic and chemolitotrophic bacteria. It was found that besides the well-known hydrocarbon-degrading aerobic/facultative anaerobic biofilm-forming organisms (e.g., Azoarcus, Leptothrix, Acidovorax, Thauera, Pseudomonas, etc.), representatives of Fe(2+)-and Mn(2+)-oxidizing (Thiobacillus, Sideroxydans, Gallionella, Rhodopseudomonas, etc.) as well as of Fe(3+)- and Mn(4+)-respiring (Rhodoferax, Geobacter, Magnetospirillum, Sulfurimonas, etc.) bacteria were present in the biofilm. The predominance of β-Proteobacteria within the biofilm bacterial community in phylogenetic and functional point of view was revealed. Investigation of meta-cleavage dioxygenase and benzylsuccinate synthase (bssA) genes indicated that within the biofilm, Azoarcus, Leptothrix, Zoogloea, and Thauera species are most probably involved in intrinsic biodegradation of aromatic hydrocarbons. Polyphasic analysis of the biofilm shed light on the fact that subsurface microbial accretions might be reservoirs of novel putatively hydrocarbon-degrading bacterial species. Moreover, clogging biofilms besides their detrimental effects might supplement the efficiency of pump and treat systems.

Interface architecture determined electrocatalytic activity of Pt on vertically oriented TiO(2) nanotubes.

PubMed

Rettew, Robert E; Allam, Nageh K; Alamgir, Faisal M

2011-02-01

The surface atomic structure and chemical state of Pt is consequential in a variety of surface-intensive devices. Herein we present the direct interrelationship between the growth scheme of Pt films, the resulting atomic and electronic structure of Pt species, and the consequent activity for methanol electro-oxidation in Pt/TiO(2) nanotube hybrid electrodes. X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS) measurements were performed to relate the observed electrocatalytic activity to the oxidation state and the atomic structure of the deposited Pt species. The atomic structure as well as the oxidation state of the deposited Pt was found to depend on the pretreatment of the TiO(2) nanotube surfaces with electrodeposited Cu. Pt growth through Cu replacement increases Pt dispersion, and a separation of surface Pt atoms beyond a threshold distance from the TiO(2) substrate renders them metallic, rather than cationic. The increased dispersion and the metallic character of Pt results in strongly enhanced electrocatalytic activity toward methanol oxidation. This study points to a general phenomenon whereby the growth scheme and the substrate-to-surface-Pt distance dictates the chemical state of the surface Pt atoms, and thereby, the performance of Pt-based surface-intensive devices.

Environmental Niche Overlap between Common and Dusky Dolphins in North Patagonia, Argentina.

PubMed

Svendsen, Guillermo Martín; Romero, María Alejandra; Williams, Gabriela Noemí; Gagliardini, Domingo Antonio; Crespo, Enrique Alberto; Dans, Silvana Laura; González, Raúl Alberto

2015-01-01

Research on the ecology of sympatric dolphins has increased worldwide in recent decades. However, many dolphin associations such as that between common dolphins (Delphinus delphis) and dusky dolphins (Lagenorhynchus obscurus) are poorly understood. The present study was conducted in the San Matías Gulf (SMG) ecosystem (North Patagonia, Argentina) where a high diet overlap among both species was found. The main objective of the present work was to explore the niche overlap of common and dusky dolphins in the habitat and temporal dimensions. The specific aims were (a) to evaluate the habitat use strategies of both species through a comparison of their group attributes (social composition, size and activity), and (b) to evaluate their habitat preferences and habitat overlap through Environmental Niche modeling considering two oceanographic seasons. To accomplish these aims, we used a historic database of opportunistic and systematic records collected from 1983 to 2011. Common and dusky dolphins exhibited similar patterns of group size (from less than 10 to more than 100 individuals), activity (both species use the area to feed, nurse, and copulate), and composition (adults, juveniles, and mothers with calves were observed for both species). Also, both species were observed travelling and feeding in mixed-species groups. Specific overlap indices were higher for common dolphins than for dusky dolphins, but all indices were low, suggesting that they are mainly segregated in the habitat dimension. In the case of common dolphins, the best habitats were located in the northwest of the gulf far from the coast. In the warm season they prefer areas with temperate sea surface and in the cold season they prefer areas with relatively high variability of sea surface temperature. Meanwhile, dusky dolphins prefer areas with steep slopes close to the coast in the southwestern sector of the gulf in both seasons.

Variation and temporal patterns in the composition of the surface ichthyoplankton in the southern Bay of Biscay (W. Atlantic)

NASA Astrophysics Data System (ADS)

d'Elbée, Jean; Castège, Iker; Hémery, Georges; Lalanne, Yann; Mouchès, Claude; Pautrizel, Françoise; D'Amico, Frank

2009-05-01

From September 2000 to December 2006, surface plankton samples were collected on a monthly basis, from a station located in the southern Bay of Biscay (43°37N; 1°43W France), near the deep Capbreton canyon. In this paper, the results for the ichthyoplankton assemblage are presented. Among the 62 taxa recorded, only 35 were present in the larval stage whilst only 10 were represented by their eggs. Taxa represented by both stages (eggs+larvae; N=17) had the highest abundance. The presence in the surface plankton assemblage of species, at either or both stage, is interpreted within the context of the bathymetric distribution of species. The maxima in abundance and diversity occurred in February-March, for eggs, and May-June, for larvae. This 3-month time-lag between the stages is proposed to be related to the timing of egg spawning and larval recruitment to the pelagic environment. Mean egg abundances (82.4±29.8 eggs/10 m 2) were 10-fold higher than the larval abundances (7.1±1.8 larvae/10 m 2). Despite pronounced monthly variability, no statistically significant decrease in either egg or larvae abundance was observed during this 6-year study period. Compared with previous published studies, this study shows that the peak in ichthyoplankton diversity occurred two months earlier. In addition, the spawning period occurred over the whole year, even during autumn and winter. Using ordination techniques, the annual sequence appearance of taxa are described at the study site: Gadiforms, Ammodytidae and Pleuronectiforms were present during the winter whilst Sparidae, Blennidae, Labridae and Gobiidae, formed the summer group. Only three species, European anchovy Engraulis encrasicolus, European pilchard Sardina pilchardus and Atlantic horse mackerel Trachurus trachurus were recorded throughout the year.

Evolution at the tips: Asclepias phylogenomics and new perspectives on leaf surfaces.

PubMed

Fishbein, Mark; Straub, Shannon C K; Boutte, Julien; Hansen, Kimberly; Cronn, Richard C; Liston, Aaron

2018-03-01

Leaf surface traits, such as trichome density and wax production, mediate important ecological processes such as anti-herbivory defense and water-use efficiency. We present a phylogenetic analysis of Asclepias plastomes as a framework for analyzing the evolution of trichome density and presence of epicuticular waxes. We produced a maximum-likelihood phylogeny using plastomes of 103 species of Asclepias. We reconstructed ancestral states and used model comparisons in a likelihood framework to analyze character evolution across Asclepias. We resolved the backbone of Asclepias, placing the Sonoran Desert clade and Incarnatae clade as successive sisters to the remaining species. We present novel findings about leaf surface evolution of Asclepias-the ancestor is reconstructed as waxless and sparsely hairy, a macroevolutionary optimal trichome density is supported, and the rate of evolution of trichome density has accelerated. Increased sampling and selection of best-fitting models of evolution provide more resolved and robust estimates of phylogeny and character evolution than obtained in previous studies. Evolutionary inferences are more sensitive to character coding than model selection. © 2018 The Authors. American Journal of Botany is published by Wiley Periodicals, Inc. on behalf of the Botanical Society of America.

Volatiles and Nonvolatiles in Flourensia campestris Griseb. (Asteraceae), How Much Do Capitate Glandular Trichomes Matter?

PubMed

Piazza, Leonardo A; López, Daniela; Silva, Mariana P; López Rivilli, Marisa J; Tourn, Mónica G; Cantero, Juan J; Scopel, Ana L

2018-03-01

The distribution and ultrastructure of capitate glandular trichomes (GTs) in Flourensia species (Asteraceae) have been recently elucidated, but their metabolic activity and potential biological function remain unexplored. Selective nonvolatile metabolites from isolated GTs were strikingly similar to those found on leaf surfaces. The phytotoxic allelochemical sesquiterpene (-)-hamanasic acid A ((-)-HAA) was the major constituent (ca. 40%) in GTs. Although GTs are quaternary ammonium compounds (QACs)-accumulating species, glycine betaine was not found in GTs; it was only present in the leaf mesophyll. Two (-)-HAA accompanying surface secreted products: compounds 4-hydroxyacetophenone (piceol; 1) and 2-hydroxy-5-methoxyacetophenone (2), which were isolated and fully characterized (GC/MS, NMR), were present in the volatiles found in GTs. The essential oils of fresh leaves revealed ca. 33% monoterpenes, 26% hydrocarbon- and 30% oxygenated sesquiterpenes, most of them related to cadinene and bisabolene derivatives. Present results suggest a main role of GTs in determining the volatile and nonvolatile composition of F. campestris leaves. Based on the known activities of the compounds identified, it can be suggested that GTs in F. campestris would play key ecological functions in plant-pathogen and plant-plant interactions. In addition, the strikingly high contribution of compounds derived from cadinene and bisabolene pathways, highlights the potential of this species as a source of high-valued bioproducts. © 2018 Wiley-VHCA AG, Zurich, Switzerland.

Chemical mechanisms of photocatalytic de-soiling and de-polluting processes in indoor environments and urban surfaces

NASA Astrophysics Data System (ADS)

Sleiman, M.; Rosseler, O.; Montesinos, N.; Litter, M.; Bikiel, D.; Kirchstetter, T.; Bluhm, H.; Ahmed, M.; Salmeron, M.; Destaillats, H.

2013-12-01

Photocatalysis has been postulated as a promising approach for the de-pollution of indoor air and urban atmospheres, and for self-cleaning surfaces. Building materials and coatings containing nano-sized TiO2 photocatalytic functionalities are gaining market share, including self-cleaning building envelope materials (coatings, mortar, plaster, architectural fabrics and tiles) and indoor air purifiers. While many studies have reported good performance of photocatalysis in the removal of organic pollutants from indoor air, more information is needed to understand secondary emissions of potentially harmful byproducts from photocatalytic air cleaners. This presentation will describe analytical methods and experimental results from room-sized chamber experiments using a realistic challenge VOC mixture at low ppb levels. We will also present results from separate studies that used synchrotron-based surface spectroscopic and mass spectrometric methods to better understand the photocatalytic mechanisms that regulate the de-soiling and de-polluting activity. Two photocatalytic processes were studied: de-noxification (NOx removal) and de-soiling (removal of deposited black carbon or soot). Ambient pressure XPS was used to study surface and gas-phase species formed during adsorption of NO2 on TiO2 and subsequent UV irradiation at λ = 365 nm. The results illustrate how NOx chemistry on TiO2 surfaces can be affected by the presence of water vapor, heteroatoms present as impurities, and carbonaceous soiling. The reactivity of NOx and NO3- on surfaces leads to reduced adsorbed and gas-phase nitrogenated species. These processes need to be considered in the engineering of depolluting materials and incorporated into atmospheric models. De-soiling properties were investigated by analyzing soot oxidation on TiO2 surfaces. Model soot samples were used as surrogates of urban grime. Using laser desorption coupled with time-of-flight (TOF) mass spectrometry synchrotron ionization, we investigated the mechanisms of photocatalytic soot removal under UVA irradiation. Ancillary reflectance measurements were performed to determine the efficiency and kinetics of soot removal.

Method and apparatus for confinement of ions in the presence of a neutral gas

DOEpatents

Peurrung, A.J.; Barlow, S.E.

1999-08-03

The present invention is an apparatus and method for combining ions with a neutral gas and flowing the mixture with a radial flow component through a magnetic field so that the weakly ionized gas is confined by the neutral gas. When the weakly ionized gas is present in sufficient density, a weakly ionized non-neutral plasma is formed that may be trapped in accordance with the present invention. Applications for a weakly ionized non-neutral plasma exploit the trap`s ability to store and manipulate ionic species in the presence of neutral gas. The trap may be connected to a mass spectrometer thereby permitting species identification after a fixed period of time. Delicate and/or heavy particles such as clusters may be held and studied in a ``gentle`` environment. In addition, the trap can provide a relatively intense, low-energy source of a particular ion species for surface implantation or molecular chemistry. Finally, a long trap may permit spectroscopy of unprecedented accuracy to be performed on ionic species. 4 figs.

Reforestation species study on a reclaimed surface mine in western Maryland

Treesearch

Jay A. Engle

1980-01-01

Westvaco Forest Research established a species comparison test including eighteen species of trees in the spring of 1978 on a recently reclaimed surface mine in Garrett County, Maryland. After two growing seasons height growth of all species has not been impressive. Seven species have better than 75 percent survival with pitch pine being best. Seven other species have...

Surface interaction between cubic phase NaNbO3 nanoflowers and Ru nanoparticles for enhancing visible-light driven photosensitized photocatalysis

NASA Astrophysics Data System (ADS)

Chen, Wei; Hu, Yin; Ba, Mingwei

2018-03-01

Ru nanoparticles supported on perovskite NaNbO3 with cubic crystal structure and nanoflower-like morphology was prepared by a convenient solvothermal method combined with photo-deposition technique. Crystal structure, chemical component and surface valence states determined by XRD, XPS, TEM and SEM demonstrated the metastable cubic phase of perovskite NaNbO3, and its modified surface by Ru species. Optical and electrochemical analysis, such as UV-vis DRS, OTCS and EIS, indicated the excellent photoelectrochemical properties and the efficient electron transfer of the composites. Compared with naked and Ru-doped NaNbO3, the composite photocatalyst exhibited outstanding performance for the degradation of RhB under visible light irradiation due to the dye self-photosensitization and the surface interaction between Ru metal nanoparticles and semiconductor. In-situ reduction of surface Ru oxide species in the photocatalytic process assisted the further improvement of the photocatalytic activity and stability. Investigation of the main active species during the photocatalysis confirmed the efficient transfer of the photo-generated electrons and the positive effect of oxygen defects in NaNbO3. Finally, possible mechanism of the present visible-light driven photocatalysis was proposed in detail. This work provided an alternative strategy to enhance the visible-light photocatalytic efficiency of the catalyst with wide band gap on the basis of the synergistic effect of dye self-photosensitization, interaction between NaNbO3 and its surface Ru nanoparticles, and the "self-doping" of oxygen defects in NaNbO3.

A new species of the genus Theloderma Tschudi, 1838 (Amphibia: Anura: Rhacophoridae) from Tay Nguyen Plateau, central Vietnam.

PubMed

Poyarkov, Nikolay A; Kropachev, Ivan I; Gogoleva, Svetlana S; Orlov, Nikolai L

2018-04-20

A new species of small tree frog from a primary montane tropical forest of central Vietnam, Tay Nguyen Plateau, is described based on morphological, molecular, and acoustic evidence. The Golden Bug-Eyed Frog, Theloderma auratum sp. nov., is distinguishable from its congeners and other small rhacophorid species based on a combination of the following morphological attributes: (1) bony ridges on head absent; (2) smooth skin completely lacking calcified warts or asperities; (3) pointed elongated tapering snout; (4) vocal opening in males absent; (5) vomerine teeth absent; (6) males of small body size (SVL 21.8-26.4 mm); (7) head longer than wide; ED/SVL ratio 13%-15%; ESL/SVL ratio 16%-20%; (8) small tympanum (TD/EL ratio 50%-60%) with few tiny tubercles; (9) supratympanic fold absent; (10) ventral surfaces completely smooth; (11) webbing between fingers absent; (12) outer and inner metacarpal tubercles present, supernumerary metacarpal tubercle single, medial, oval in shape; (13) toes half-webbed: I 2-2¼ II 1½-2¾ III 2-3¼ IV 3-1½ V; (14) inner metatarsal tubercle present, oval; outer metatarsal tubercle absent; (15) iris bicolored; (16) dorsal surfaces golden-yellow with sparse golden-orange speckling or reticulations and few small dark-brown spots; (17) lateral sides of head and body with wide dark reddish-brown to black lateral stripes, clearly separated from lighter dorsal coloration by straight contrasting edge; (18) ventral surfaces of body, throat, and chest greyish-blue with indistinct brown confluent blotches; (19) upper eyelids with few (3-5) very small flat reddish superciliary tubercles; (20) limbs dorsally reddish-brown, ventrally brown with small bluish-white speckles. The new species is also distinct from all congeners in 12S rRNA to 16S rRNA mitochondrial DNA fragment sequences (uncorrected genetic distance P>8.9%). Advertisement call and tadpole morphology of the new species are described. Our molecular data showed Theloderma auratum sp. nov. to be a sister species of Th. palliatum from Langbian Plateau in southern Vietnam.

A new species of the genus Theloderma Tschudi, 1838 (Amphibia: Anura: Rhacophoridae) from Tay Nguyen Plateau, central Vietnam

PubMed Central

Poyarkov, Nikolay A.; Kropachev, Ivan I.; Gogoleva, Svetlana S.; Orlov, Nikolai L.

2018-01-01

A new species of small tree frog from a primary montane tropical forest of central Vietnam, Tay Nguyen Plateau, is described based on morphological, molecular, and acoustic evidence. The Golden Bug-Eyed Frog, Theloderma auratum sp. nov., is distinguishable from its congeners and other small rhacophorid species based on a combination of the following morphological attributes: (1) bony ridges on head absent; (2) smooth skin completely lacking calcified warts or asperities; (3) pointed elongated tapering snout; (4) vocal opening in males absent; (5) vomerine teeth absent; (6) males of small body size (SVL 21.8–26.4 mm); (7) head longer than wide; ED/SVL ratio 13%–15%; ESL/SVL ratio 16%–20%; (8) small tympanum (TD/EL ratio 50%–60%) with few tiny tubercles; (9) supratympanic fold absent; (10) ventral surfaces completely smooth; (11) webbing between fingers absent; (12) outer and inner metacarpal tubercles present, supernumerary metacarpal tubercle single, medial, oval in shape; (13) toes half-webbed: I 2–2¼ II 1½–2¾ III 2–3¼ IV 3–1½ V; (14) inner metatarsal tubercle present, oval; outer metatarsal tubercle absent; (15) iris bicolored; (16) dorsal surfaces golden-yellow with sparse golden-orange speckling or reticulations and few small dark-brown spots; (17) lateral sides of head and body with wide dark reddish-brown to black lateral stripes, clearly separated from lighter dorsal coloration by straight contrasting edge; (18) ventral surfaces of body, throat, and chest greyish-blue with indistinct brown confluent blotches; (19) upper eyelids with few (3–5) very small flat reddish superciliary tubercles; (20) limbs dorsally reddish-brown, ventrally brown with small bluish-white speckles. The new species is also distinct from all congeners in 12S rRNA to 16S rRNA mitochondrial DNA fragment sequences (uncorrected genetic distance P>8.9%). Advertisement call and tadpole morphology of the new species are described. Our molecular data showed Theloderma auratum sp. nov. to be a sister species of Th. palliatum from Langbian Plateau in southern Vietnam. PMID:29683110

The Anti-Biofouling Properties of Superhydrophobic Surfaces are Short-Lived.

PubMed

Hwang, Gi Byoung; Page, Kristopher; Patir, Adnan; Nair, Sean P; Allan, Elaine; Parkin, Ivan P

2018-06-12

Superhydrophobic surfaces are present in nature on the leaves of many plant species. Water rolls on these surfaces, and the rolling motion picks up particles including bacteria and viruses. Man-made superhydrophobic surfaces have been made in an effort to reduce biofouling. We show here that the anti-biofouling property of a superhydrophobic surface is due to an entrapped air-bubble layer that reduces contact between the bacteria and the surface. Further, we showed that prolonged immersion of superhydrophobic surfaces in water led to loss of the bubble-layer and subsequent bacterial adhesion that unexpectedly exceeded that of the control materials. This behavior was not restricted to one particular type of material but was evident on different types of superhydrophobic surfaces. This work is important in that it suggests that superhydrophobic surfaces may actually encourage bacterial adhesion during longer term exposure.

A Cell-surface Phylome for African Trypanosomes

PubMed Central

Jackson, Andrew P.; Allison, Harriet C.; Barry, J. David; Field, Mark C.; Hertz-Fowler, Christiane; Berriman, Matthew

2013-01-01

The cell surface of Trypanosoma brucei, like many protistan blood parasites, is crucial for mediating host-parasite interactions and is instrumental to the initiation, maintenance and severity of infection. Previous comparisons with the related trypanosomatid parasites T. cruzi and Leishmania major suggest that the cell-surface proteome of T. brucei is largely taxon-specific. Here we compare genes predicted to encode cell surface proteins of T. brucei with those from two related African trypanosomes, T. congolense and T. vivax. We created a cell surface phylome (CSP) by estimating phylogenies for 79 gene families with putative surface functions to understand the more recent evolution of African trypanosome surface architecture. Our findings demonstrate that the transferrin receptor genes essential for bloodstream survival in T. brucei are conserved in T. congolense but absent from T. vivax and include an expanded gene family of insect stage-specific surface glycoproteins that includes many currently uncharacterized genes. We also identify species-specific features and innovations and confirm that these include most expression site-associated genes (ESAGs) in T. brucei, which are absent from T. congolense and T. vivax. The CSP presents the first global picture of the origins and dynamics of cell surface architecture in African trypanosomes, representing the principal differences in genomic repertoire between African trypanosome species and provides a basis from which to explore the developmental and pathological differences in surface architectures. All data can be accessed at: http://www.genedb.org/Page/trypanosoma_surface_phylome. PMID:23556014

Influence of the sulfur species reactivity on biofilm conformation during pyrite colonization by Acidithiobacillus thiooxidans.

PubMed

Lara, René H; García-Meza, J Viridiana; Cruz, Roel; Valdez-Pérez, Donato; González, Ignacio

2012-08-01

Massive pyrite (FeS₂) electrodes were potentiostatically modified by means of variable oxidation pulse to induce formation of diverse surface sulfur species (S(n)²⁻, S⁰). The evolution of reactivity of the resulting surfaces considers transition from passive (e.g., Fe(1-x )S₂) to active sulfur species (e.g., Fe(1-x )S(2-y ), S⁰). Selected modified pyrite surfaces were incubated with cells of sulfur-oxidizing Acidithiobacillus thiooxidans for 24 h in a specific culture medium (pH 2). Abiotic control experiments were also performed to compare chemical and biological oxidation. After incubation, the attached cells density and their exopolysaccharides were analyzed by confocal laser scanning microscopy (CLMS) and atomic force microscopy (AFM) on bio-oxidized surfaces; additionally, S(n)²⁻/S⁰ speciation was carried out on bio-oxidized and abiotic pyrite surfaces using Raman spectroscopy. Our results indicate an important correlation between the evolution of S(n)²⁻/S⁰ surface species ratio and biofilm formation. Hence, pyrite surfaces with mainly passive-sulfur species were less colonized by A. thiooxidans as compared to surfaces with active sulfur species. These results provide knowledge that may contribute to establishing interfacial conditions that enhance or delay metal sulfide (MS) dissolution, as a function of the biofilm formed by sulfur-oxidizing bacteria.

Systematic, cross-cortex variation in neuron numbers in rodents and primates.

PubMed

Charvet, Christine J; Cahalane, Diarmuid J; Finlay, Barbara L

2015-01-01

Uniformity, local variability, and systematic variation in neuron numbers per unit of cortical surface area across species and cortical areas have been claimed to characterize the isocortex. Resolving these claims has been difficult, because species, techniques, and cortical areas vary across studies. We present a stereological assessment of neuron numbers in layers II-IV and V-VI per unit of cortical surface area across the isocortex in rodents (hamster, Mesocricetus auratus; agouti, Dasyprocta azarae; paca, Cuniculus paca) and primates (owl monkey, Aotus trivigratus; tamarin, Saguinus midas; capuchin, Cebus apella); these chosen to vary systematically in cortical size. The contributions of species, cortical areas, and techniques (stereology, "isotropic fractionator") to neuron estimates were assessed. Neurons per unit of cortical surface area increase across the rostro-caudal (RC) axis in primates (varying by a factor of 1.64-2.13 across the rostral and caudal poles) but less in rodents (varying by a factor of 1.15-1.54). Layer II-IV neurons account for most of this variation. When integrated into the context of species variation, and this RC gradient in neuron numbers, conflicts between studies can be accounted for. The RC variation in isocortical neurons in adulthood mirrors the gradients in neurogenesis duration in development. © The Author 2013. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Ozonation and H2O2/UV treatment of clofibric acid in water: a kinetic investigation.

PubMed

Andreozzi, Roberto; Caprio, Vincenzo; Marotta, Raffaele; Radovnikovic, Anita

2003-10-31

The presence of pharmaceuticals or their active metabolites in surface and ground waters has been recently reported as mainly due to an incomplete removal of these pollutants in sewage treatment plants (STP). Advanced oxidation processes may represent a suitable tool to reduce environmental release of these species by enhancing the global efficiency of reduction of pharmaceuticals in the municipal sewage plant effluents. The present work aims at assessing the kinetics of abatement from aqueous solutions of clofibric acid (a metabolite of the blood lipid regulator clofibrate) which has been found in surface, ground and drinking waters. Ozonation and hydrogen peroxide photolysis are capable of fast removal of this species in aqueous solution, with an almost complete conversion of the organic chlorine content into chloride ions for the investigated reaction conditions. A validation of assessed kinetics at clofibric acid concentrations as low as those found in STP effluents is presented for both systems.

Losses of leaf area owing to herbivory and early senescence in three tree species along a winter temperature gradient

NASA Astrophysics Data System (ADS)

González-Zurdo, P.; Escudero, A.; Nuñez, R.; Mediavilla, S.

2016-11-01

In temperate climates, evergreen leaves have to survive throughout low temperature winter periods. Freezing and chilling injuries can lead to accelerated senescence of part of the leaf surface, which contributes to a reduction of the lifespan of the photosynthetic machinery and of leaf lifetime carbon gain. Low temperatures are also associated with changes in foliar chemistry and morphology that affect consumption by herbivores. Therefore, the severity of foliar area losses caused by accelerated senescence and herbivory can change along winter temperature gradients. The aim of this study is to analyse such responses in the leaves of three evergreen species ( Quercus ilex, Q. suber and Pinus pinaster) along a climatic gradient. The leaves of all three species presented increased leaf mass per area (LMA) and higher concentrations of structural carbohydrates in cooler areas. Only the two oak species showed visible symptoms of damage caused by herbivory, this being less intense at the coldest sites. The leaves of all three species presented chlorotic and necrotic spots that increased in size with leaf age. The foliar surface affected by chlorosis and necrosis was larger at the sites with the coldest winters. Therefore, the effects of the winter cold on the lifespan of the photosynthetic machinery were contradictory: losses of leaf area due to accelerated senescence increased, but there was a decrease in losses caused by herbivory. The final consequences for carbon assimilation strongly depend on the exact timing of the appearance of the damage resulting from low temperature and grazing by herbivores.

Plasma Technology as a New Preservation Technique

NASA Astrophysics Data System (ADS)

Rincón, R.; Calzada, M. D.

The preliminary results of using the surface wave discharge at the atmospheric pressure on groups of lentils and sherry Fino wine samples are presented. In this research, the capability of active species and UV radiation from the plasma, has been assessed on preservation of food. Besides, the generation and emission of both excited molecules in a metastable state N2}(B3Π {g-> A3}Σ u{+) and the de-excitation of species NO(A2}Σ {+) producing UV radiation have been also studied.

Response of biofilms-leaves of two submerged macrophytes to high ammonium.

PubMed

Gong, Lixue; Zhang, Songhe; Chen, Deqiang; Liu, Kaihui; Lu, Jian

2018-02-01

Submerged macrophytes can provide attached surface for biofilms (known as periphyton) growth. In the present study, the alterations in biofilms formation, and chemical compositions and physiological responses were investigated on leaves of Vallisneria asiatica and Hydrilla verticillata exposed to 0.1 mg L -1 (control) or with 10 mg L -1 NH 4 + -N for 13 days. Results from physiological and biochemical indices (content of H 2 O 2 , malondialdehyde, total chlorophyll and activity of superoxide dismutase, catalase and peroxidase) showed that high ammonium caused oxidative damage to leaves of two species of plant. Multifractal analysis (based on scanning electron microscope images) showed that for the same plant, the values of width △α (△α = α max -α min ) of the f(α) and Δf (Δf = f(α min )-f(α max )) were smaller on leaves surface of two species of plant treated with 10 mg L -1 NH 4 + -N for 13 days than their controls, suggesting high ammonium treatments reduced morphological heterogeneity of leaf surface and enhanced area of the colony-like biofilms. X-ray photoelectron spectroscopy analysis showed that C, O, N and P were dominant elements on leaves surface of two species of plant and ammonium application increased the percentage of C but decreased that of O. High ammonium increased C1 (C-C or C-H) percentage but decreased C2 (C-O) and C3 (O-C-O or C=O) percentage on leaves surface of two species of plant, indicating that ammonium stress changed the surface chemical states and thus might reduce the capacity of leaves to adsorb nutrients from water column. Our results provided useful information to understand ammonium induced toxicity to submerged macrophytes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Single particle electrochemical sensors and methods of utilization

DOEpatents

Schoeniger, Joseph [Oakland, CA; Flounders, Albert W [Berkeley, CA; Hughes, Robert C [Albuquerque, NM; Ricco, Antonio J [Los Gatos, CA; Wally, Karl [Lafayette, CA; Kravitz, Stanley H [Placitas, NM; Janek, Richard P [Oakland, CA

2006-04-04

The present invention discloses an electrochemical device for detecting single particles, and methods for using such a device to achieve high sensitivity for detecting particles such as bacteria, viruses, aggregates, immuno-complexes, molecules, or ionic species. The device provides for affinity-based electrochemical detection of particles with single-particle sensitivity. The disclosed device and methods are based on microelectrodes with surface-attached, affinity ligands (e.g., antibodies, combinatorial peptides, glycolipids) that bind selectively to some target particle species. The electrodes electrolyze chemical species present in the particle-containing solution, and particle interaction with a sensor element modulates its electrolytic activity. The devices may be used individually, employed as sensors, used in arrays for a single specific type of particle or for a range of particle types, or configured into arrays of sensors having both these attributes.

Characterization of Coke on a Pt-Re/γ-Al 2O 3 Re-Forming Catalyst: Experimental and Theoretical Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bare, Simon R.; Vila, F. D.; Charochak, Meghan E.

The characterization of coke on spent catalysts is key to understanding deactivation mechanisms in hydrocarbon transformations. Here, we report the comprehensive characterization (using laser Raman spectroscopy, 13C MAS NMR, temperature-programmed oxidation, XPS, and carbon K-edge NEXAFS) of coke on a series of spent Pt-Re re-forming catalysts as a function of time on stream and position in the catalytic bed. Laser Raman spectroscopy is shown to be rather insensitive to the carbon species present, while 13C MAS NMR finds that the carbon is present primarily as aromatic carbon. The TPO data are consistent with the coke being present on the aluminamore » support and not to a large extent covering the metallic Pt-Re nanoclusters, but the data do suggest the presence of more than one type of coke present. The carbon K-edge NEXAFS data, however, clearly differentiate the types of coke species present. In the more coked samples the features ascribed to graphite become more pronounced, together with an increase in the aromaticity, as judged by the intensity of the π* peak. With increasing amounts of carbon on the catalyst there is also a concomitant decrease in the σ* C–H peak, indicating that the carbon is becoming less hydrogenated. Furthermore, by using a linear combination of C NEXAFS spectra for n-hexane, benzene, and broadened highly oriented pyrolytic graphite (HOPG), we estimate the compositional change on the coke species, verifying the aliphatic to aromatic conversion. The data indicate that a good model for the deposited coke is that of highly defected, medium-sized rafts with a short-range polycyclic aromatic structure which have a variety of points of contact with the alumina surface, in particular with the O atoms. In agreement with the NMR, there is evidence for the C–O functionality from the presence of a shoulder in the C NEXAFS spectra that is ascribed, as a result of DFT calculations, to a 1s → π* transition of the carbon atoms bound to the oxygen of a phenoxide-like species bound to the alumina surface. Finally, these data confirm earlier Soxhlet extraction studies and show that extraction process did not substantially change the character of the coke from what it was while still in contact with the catalyst surface.« less

Characterization of Coke on a Pt-Re/γ-Al 2O 3 Re-Forming Catalyst: Experimental and Theoretical Study

DOE PAGES

Bare, Simon R.; Vila, F. D.; Charochak, Meghan E.; ...

2017-01-09

The characterization of coke on spent catalysts is key to understanding deactivation mechanisms in hydrocarbon transformations. Here, we report the comprehensive characterization (using laser Raman spectroscopy, 13C MAS NMR, temperature-programmed oxidation, XPS, and carbon K-edge NEXAFS) of coke on a series of spent Pt-Re re-forming catalysts as a function of time on stream and position in the catalytic bed. Laser Raman spectroscopy is shown to be rather insensitive to the carbon species present, while 13C MAS NMR finds that the carbon is present primarily as aromatic carbon. The TPO data are consistent with the coke being present on the aluminamore » support and not to a large extent covering the metallic Pt-Re nanoclusters, but the data do suggest the presence of more than one type of coke present. The carbon K-edge NEXAFS data, however, clearly differentiate the types of coke species present. In the more coked samples the features ascribed to graphite become more pronounced, together with an increase in the aromaticity, as judged by the intensity of the π* peak. With increasing amounts of carbon on the catalyst there is also a concomitant decrease in the σ* C–H peak, indicating that the carbon is becoming less hydrogenated. Furthermore, by using a linear combination of C NEXAFS spectra for n-hexane, benzene, and broadened highly oriented pyrolytic graphite (HOPG), we estimate the compositional change on the coke species, verifying the aliphatic to aromatic conversion. The data indicate that a good model for the deposited coke is that of highly defected, medium-sized rafts with a short-range polycyclic aromatic structure which have a variety of points of contact with the alumina surface, in particular with the O atoms. In agreement with the NMR, there is evidence for the C–O functionality from the presence of a shoulder in the C NEXAFS spectra that is ascribed, as a result of DFT calculations, to a 1s → π* transition of the carbon atoms bound to the oxygen of a phenoxide-like species bound to the alumina surface. Finally, these data confirm earlier Soxhlet extraction studies and show that extraction process did not substantially change the character of the coke from what it was while still in contact with the catalyst surface.« less

Investigation of the atmospheres of Europa, Ganymede, and Callisto with PEP/JUICE

NASA Astrophysics Data System (ADS)

Wurz, Peter; Tulej, Marek; Vorburger, Audrey; Thomas, Nicolas; Barabash, Stas; Wieser, Martin; Lammer, Helmut

2013-04-01

The Particle Environment Package (PEP) suite of instruments has been proposed for the JUICE mission, which contains sensors for the comprehensive measurements of electrons, ions and neutrals. One of the instruments for neutral particles is the Neutral and Ion Mass spectrometer instrument (NIM). NIM is a time-of-flight neutral gas and thermal ion mass spectrometer and is optimised for exospheric investigations. Full mass spectra (1 - 1000 amu, m/Δm = 1100) are recorded with high cadence, typically every 100 s, and during flybys even at 1 s cadence. In a 5-s spectrum the detection threshold is 10-16 mbar (about 1 cm-3). Various physical processes are acting on the surfaces of Jupiter's icy moons (Europa, Ganymede, Callisto) to promote material from the surface into the exosphere. These are thermal desorption (sublimation), photon stimulated desorption, ion-induced sputtering, and micro-meteorite impact vaporisation (Wurz and Lammer, 2003; Wurz et al., 2010). At Europa, sputtering is the most important surface release process (Johnson et al., 2009), which releases all species present on the surface more or less stoichiometrically into the exosphere, allowing to derive the chemical composition of the surface from the exospheric measurements. However, the chemical composition of the surface is modified by the bombardment of energetic electrons and ions, and the ultraviolet radiation. For example, species like H2, O2, H2O2 or O3 begin to be produced in the top surface layer and are later released into the exosphere by various means. Also, the co-rotation plasma's electrons and to a smaller extent the UV photons cause fragmentation and ionisation of molecules at some locations in these exospheres. We calculated the expected densities for established and expected species in Jupiter's icy moons exospheres. We find that for the planned JUICE trajectories near these moons that NIM will record most known species because of NIM's high sensitivity, even in the presence of the severe radiation environment at Europa. With NIM's dynamic range of 105 one can measure even the D/H ratios during flybys. NIM offers the possibility of detection of yet undiscovered species, with the likely candidates from the non-ice materials Mg, Al, Si, and Ca, that will help understand the mineralogical composition of the surfaces of the moons. NIM's high mass resolution, range and sensitivity are critical in contributing to the habitability assessment of Europa by being able to investigate localised patchy regions of the exosphere indicative of sub-surface venting and to resolve chemical composition.

First-principles surface interaction studies of aluminum-copper and aluminum-copper-magnesium secondary phases in aluminum alloys

NASA Astrophysics Data System (ADS)

da Silva, Thiago H.; Nelson, Eric B.; Williamson, Izaak; Efaw, Corey M.; Sapper, Erik; Hurley, Michael F.; Li, Lan

2018-05-01

First-principles density functional theory-based calculations were performed to study θ-phase Al2Cu, S-phase Al2CuMg surface stability, as well as their interactions with water molecules and chloride (Cl-) ions. These secondary phases are commonly found in aluminum-based alloys and are initiation points for localized corrosion. Density functional theory (DFT)-based simulations provide insight into the origins of localized (pitting) corrosion processes of aluminum-based alloys. For both phases studied, Cl- ions cause atomic distortions on the surface layers. The nature of the distortions could be a factor to weaken the interlayer bonds in the Al2Cu and Al2CuMg secondary phases, facilitating the corrosion process. Electronic structure calculations revealed not only electron charge transfer from Cl- ions to alloy surface but also electron sharing, suggesting ionic and covalent bonding features, respectively. The S-phase Al2CuMg structure has a more active surface than the θ-phase Al2Cu. We also found a higher tendency of formation of new species, such as Al3+, Al(OH)2+, HCl, AlCl2+, Al(OH)Cl+, and Cl2 on the S-phase Al2CuMg surface. Surface chemical reactions and resultant species present contribute to establishment of local surface chemistry that influences the corrosion behavior of aluminum alloys.

Influence of the three-dimensional heterogeneous roughness on electrokinetic transport in microchannels.

PubMed

Hu, Yandong; Werner, Carsten; Li, Dongqing

2004-12-15

Surface roughness has been considered as a passive means of enhancing species mixing in electroosmotic flow through microfluidic systems. It is highly desirable to understand the synergetic effect of three-dimensional (3D) roughness and surface heterogeneity on the electrokinetic flow through microchannels. In this study, we developed a three-dimensional finite-volume-based numerical model to simulate electroosmotic transport in a slit microchannel (formed between two parallel plates) with numerous heterogeneous prismatic roughness elements arranged symmetrically and asymmetrically on the microchannel walls. We consider that all 3D prismatic rough elements have the same surface charge or zeta potential, the substrate (the microchannel wall) surface has a different zeta potential. The results showed that the rough channel's geometry and the electroosmotic mobility ratio of the roughness elements' surface to that of the substrate, epsilon(mu), have a dramatic influence on the induced-pressure field, the electroosmotic flow patterns, and the electroosmotic flow rate in the heterogeneous rough microchannels. The associated sample-species transport presents a tidal-wave-like concentration field at the intersection between four neighboring rough elements under low epsilon(mu) values and has a concentration field similar to that of the smooth channels under high epsilon(mu) values.

Culturable fungi in potting soils and compost.

PubMed

Haas, Doris; Lesch, Susanne; Buzina, Walter; Galler, Herbert; Gutschi, Anna Maria; Habib, Juliana; Pfeifer, Bettina; Luxner, Josefa; Reinthaler, Franz F

2016-11-01

In the present study the spectrum and the incidence of fungi in potting soils and compost was investigated. Since soil is one of the most important biotopes for fungi, relatively high concentrations of fungal propagules are to be expected. For detection of fungi, samples of commercial soils, compost and soils from potted plants (both surface and sub-surface) were suspended and plated onto several mycological media. The resulting colonies were evaluated qualitatively and quantitatively. The results from the different sampling series vary, but concentrations on the surface of potted plants and in commercial soils are increased tenfold compared to compost and sub-surface soils. Median values range from 9.5 × 10(4) colony forming units (CFU)/g to 5.5 × 10(5) CFU/g. The spectrum of fungi also varies in the soils. However, all sampling series show high proportion of Aspergillus and Penicillium species, including potentially pathogenic species such as Aspergillus fumigatus. Cladosporium, a genus dominant in the ambient air, was found preferably in samples which were in contact with the air. The results show that potentially pathogenic fungi are present in soils. Immunocompromised individuals should avoid handling soils or potted plants in their immediate vicinity. © The Author 2016. Published by Oxford University Press on behalf of The International Society for Human and Animal Mycology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Co-adsorption of water and oxygen on GaN: Effects of charge transfer and formation of electron depletion layer.

PubMed

Wang, Qi; Puntambekar, Ajinkya; Chakrapani, Vidhya

2017-09-14

Species from ambient atmosphere such as water and oxygen are known to affect electronic and optical properties of GaN, but the underlying mechanism is not clearly known. In this work, we show through careful measurement of electrical resistivity and photoluminescence intensity under various adsorbates that the presence of oxygen or water vapor alone is not sufficient to induce electron transfer to these species. Rather, the presence of both water and oxygen is necessary to induce electron transfer from GaN that leads to the formation of an electron depletion region on the surface. Exposure to acidic gases decreases n-type conductivity due to increased electron transfer from GaN, while basic gases increase n-type conductivity and PL intensity due to reduced charge transfer from GaN. These changes in the electrical and optical properties, as explained using a new electrochemical framework based on the phenomenon of surface transfer doping, suggest that gases interact with the semiconductor surface through electrochemical reactions occurring in an adsorbed water layer present on the surface.

Oxygen isotope ranking of late Eocene and Oligocene planktonic foraminifers: Implications for Oligocene sea-surface temperatures and global ice-volume

USGS Publications Warehouse

Poore, R.Z.; Matthews, R.K.

1984-01-01

Oxygen isotope analyses of late Eocene and Oligocene planktonic foraminifers from low and middle latitude sites in the Atlantic Basin show that different species from the same samples can yield significantly different isotopic values. The range of isotopic values observed between species is greatest at low-latitudes and declines poleward. Many planktonic foraminifers exhibit a systematic isotopic ranking with respect to each other and can therefore be grouped on the basis of their isotopic ranking. The isotopic ranking of some taxa, however, appears to vary geographically and/or through time. Isotopic and paleontologic data from DSDP Site 522 indicate that commonly used isotopic temperature scales underestimate Oligocene sea surface temperatures. We suggest these temperature scales require revision to reflect the presence of Oligocene glaciation. Comparison of isotopic and paleontologic data from Sites 522, 511 and 277 suggests cold, low-salinity surface waters were present in high southern latitudes during the early Oligocene. Lowsalinity, high latitude surface waters could be caused by Eocene/Oligocene paleogeography or by the production of warm saline bottom water. ?? 1984.

Branch length similarity entropy-based descriptors for shape representation

NASA Astrophysics Data System (ADS)

Kwon, Ohsung; Lee, Sang-Hee

2017-11-01

In previous studies, we showed that the branch length similarity (BLS) entropy profile could be successfully used for the shape recognition such as battle tanks, facial expressions, and butterflies. In the present study, we proposed new descriptors, roundness, symmetry, and surface roughness, for the recognition, which are more accurate and fast in the computation than the previous descriptors. The roundness represents how closely a shape resembles to a circle, the symmetry characterizes how much one shape is similar with another when the shape is moved in flip, and the surface roughness quantifies the degree of vertical deviations of a shape boundary. To evaluate the performance of the descriptors, we used the database of leaf images with 12 species. Each species consisted of 10 - 20 leaf images and the total number of images were 160. The evaluation showed that the new descriptors successfully discriminated the leaf species. We believe that the descriptors can be a useful tool in the field of pattern recognition.

Analysis of mercury adsorption at the gibbsite-water interface using the CD-MUSIC model.

PubMed

Park, Chang Min

2018-05-22

Mercury (Hg), one of the most toxic substances in nature, has long been released during the anthropogenic activity. A correct description of the adsorptive behavior of mercury is important to gain a better insight into its fate and transport in natural mineral surfaces, which will be a prerequisite for the development of surface complexation model for the adsorption processes. In the present study, simulation experiments on macroscopic Hg(II) sorption by gibbsite (α-Al(OH) 3 ), a representative aluminum (hydr)oxide mineral, were performed using the charge distribution and multi-site complexation (CD-MUSIC) approach with 1-pK triple plane model (TPM). For this purpose, several data sets which had already been reported in the literature were employed to analyze the effect of pH, ionic strength, and co-exisiting ions (NO 3 - and Cl - ) on the Hg(II) adsorption onto gibbsite. Sequential optimization approach was used to determine the acidity and asymmetric binding constants for electrolyte ions and the affinity constants of the surface species through the model simulation using FITEQLC (a modified code of FITEQL 4.0). The model successfully incorporated the presence of inorganic ligands at the dominant edge (100) face of gibbsite with consistent surface species, which was evidenced by molecular scale analysis. The model was verified with an independent set of Hg(II) adsorption data incorporating carbonate binding species in an open gibbsite-water system.

Nanoparticles for Control of Biofilms of Acinetobacter Species

PubMed Central

Singh, Richa; Nadhe, Shradhda; Wadhwani, Sweety; Shedbalkar, Utkarsha; Chopade, Balu Ananda

2016-01-01

Biofilms are the cause of 80% of microbial infections. Acinetobacter species have emerged as multi- and pan-drug-resistant bacteria and pose a great threat to human health. These act as nosocomial pathogens and form excellent biofilms, both on biotic and abiotic surfaces, leading to severe infections and diseases. Various methods have been developed for treatment and control of Acinetobacter biofilm including photodynamic therapy, radioimmunotherapy, prophylactic vaccines and antimicrobial peptides. Nanotechnology, in the present scenario, offers a promising alternative. Nanomaterials possess unique properties, and multiple bactericidal mechanisms render them more effective than conventional drugs. This review intends to provide an overview of Acinetobacter biofilm and the significant role of various nanoparticles as anti-biofouling agents, surface-coating materials and drug-delivery vehicles for biofilm control and treatment of Acinetobacter infections. PMID:28773507

Validation of the Applied Biosystems 7500 Fast Instrument for Detection of Listeria Species with the SureTect Listeria Species PCR Assay.

PubMed

Cloke, Jonathan; Arizanova, Julia; Crabtree, David; Simpson, Helen; Evans, Katharine; Vaahtoranta, Laura; Palomäki, Jukka-Pekka; Artimo, Paulus; Huang, Feng; Liikanen, Maria; Koskela, Suvi; Chen, Yi

2016-01-01

The Thermo Scientific™ SureTect™ Listeria species Real-Time PCR Assay was certified during 2013 by the AOAC Research Institute (RI) Performance Tested Methods(SM) program as a rapid method for the detection of Listeria species from a wide range of food matrixes and surface samples. A method modification study was conducted in 2015 to extend the matrix claims of the product to a wider range of food matrixes. This report details the method modification study undertaken to extend the use of this PCR kit to the Applied Biosystems™ 7500 Fast PCR Instrument and Applied Biosystems RapidFinder™ Express 2.0 software allowing use of the assay on a 96-well format PCR cycler in addition to the current workflow, using the 24-well Thermo Scientific PikoReal™ PCR Instrument and Thermo Scientific SureTect software. The method modification study presented in this report was assessed by the AOAC-RI as being a level 2 method modification study, necessitating a method developer study on a representative range of food matrixes covering raw ground turkey, 2% fat pasteurized milk, and bagged lettuce as well as stainless steel surface samples. All testing was conducted in comparison to the reference method detailed in International Organization for Standardization (ISO) 6579:2002. No significant difference by probability of detection statistical analysis was found between the SureTect Listeria species PCR Assay or the ISO reference method methods for any of the three food matrixes and the surface samples analyzed during the study.

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Sean W., E-mail: sean.king@intel.com; Davis, Robert F.; Carter, Richard J.

The desorption kinetics of molecular hydrogen (H{sub 2}) from silicon (001) surfaces exposed to aqueous hydrogen fluoride and remote hydrogen plasmas were examined using temperature programmed desorption. Multiple H{sub 2} desorption states were observed and attributed to surface monohydride (SiH), di/trihydride (SiH{sub 2/3}), and hydroxide (SiOH) species, subsurface hydrogen trapped at defects, and hydrogen evolved during the desorption of surface oxides. The observed surface hydride species were dependent on the surface temperature during hydrogen plasma exposure with mono, di, and trihydride species being observed after low temperature exposure (150 °C), while predominantly monohydride species were observed after higher temperature exposure (450 °C).more » The ratio of surface versus subsurface H{sub 2} desorption was also found to be dependent on the substrate temperature with 150 °C remote hydrogen plasma exposure generally leading to more H{sub 2} evolved from subsurface states and 450 °C exposure leading to more H{sub 2} desorption from surface SiH{sub x} species. Additional surface desorption states were observed, which were attributed to H{sub 2} desorption from Si (111) facets formed as a result of surface etching by the remote hydrogen plasma or aqueous hydrogen fluoride treatment. The kinetics of surface H{sub 2} desorption were found to be in excellent agreement with prior investigations of silicon surfaces exposed to thermally generated atomic hydrogen.« less

Uranium(VI) adsorption to ferrihydrite: Application of a surface complexation model

USGS Publications Warehouse

Waite, T.D.; Davis, J.A.; Payne, T.E.; Waychunas, G.A.; Xu, N.

1994-01-01

A study of U(VI) adsorption by ferrihydrite was conducted over a wide range of U(VI) concentrations, pH, and at two partial pressures of carbon dioxide. A two-site (strong- and weak-affinity sites, FesOH and FewOH, respectively) surface complexation model was able to describe the experimental data well over a wide range of conditions, with only one species formed with each site type: an inner-sphere, mononuclear, bidentate complex of the type (FeO2)UO2. The existence of such a surface species was supported by results of uranium EXAFS spectroscopy performed on two samples with U(VI) adsorption density in the upper range observed in this study (10 and 18% occupancy of total surface sites). Adsorption data in the alkaline pH range suggested the existence of a second surface species, modeled as a ternary surface complex with UO2CO30 binding to a bidentate surface site. Previous surface complexation models for U(VI) adsorption have proposed surface species that are identical to the predominant aqueous species, e.g., multinuclear hydrolysis complexes or several U(VI)-carbonate complexes. The results demonstrate that the speciation of adsorbed U(VI) may be constrained by the coordination environment at the surface, giving rise to surface speciation for U(VI) that is significantly less complex than aqueous speciation.

Peristome as a potential tool for delimiting Bryum Hedw. (Bryaceae) from India.

PubMed

Bansal, Pooja; Nath, Virendra

2018-02-26

The peristome, an interesting and important taxonomic structure used in the systematics of mosses, is for the first time studied in detail for 21 taxa of Bryum, which constitute a fraction of Indian representatives. Macro- and micro-morphological characters including color, size and length of two components of peristome, tapering pattern, median line, and papillosity at upper part under light microscope; width of exostome border, number and inner surface of ventral trabeculae, presence or absence of longitudinal/oblique septae between ventral trabeculae, pattern of exostome surface and height of endostomial basal membrane, adherence, perforations, and surface of cilia under scanning electron microscope were examined to bring out submicroscopic differences. Detail surface structure of eight taxa, viz., B. apalodictyoides, B. evanidinerve, B. pachytheca, B. pseudotriquetrum var. subrotundum, B. reflexifolium, B. thomsonii, B. tuberosum, and B. turbinatum, under LM and nine species, namely, B. apalodictyoides, B. apiculatum, B. argenteum, B. billarderi, B. dichotomum, B. evanidinerve, B. recurvulum, B. turbinatum, and B. uliginosum, under SEM is being provided for the first time. Description of peristome surface and a key based on SEM and other taxonomical features is also being provided. The data obtained from the present study suggest that the species of this genus can easily be distinguished on the basis of peristomial surface pattern.

The effect of surface pre-conditioning treatments on the local composition of Zr-based conversion coatings formed on aluminium alloys

NASA Astrophysics Data System (ADS)

Cerezo, J.; Vandendael, I.; Posner, R.; de Wit, J. H. W.; Mol, J. M. C.; Terryn, H.

2016-03-01

This study investigates the effect of different alkaline, acidic and thermal pre-conditioning treatments applied to different Al alloy surfaces. The obtained results are compared to the characteristics of Zr-based conversion coatings that were subsequently generated on top of these substrates. Focus is laid on typical elemental distributions on the sample surfaces, in particular on the amount of precipitated functional additives such as Cu species that are present in the substrate matrix as well as in the conversion bath solutions. To this aim, Field Emission Auger Electron spectra, depth profiles and surface maps with superior local resolution were acquired and compared to scanning electron microscopy images of the sample. The results show how de-alloying processes, which occur at and around intermetallic particles in the Al matrix during typical industrial alkaline or acidic cleaning procedures, provide a significant source of crystallization cores for any following coating processes. This is in particular due for Cu-species, as the resulting local Cu structures on the surface strongly affect the film formation and compositions of state-of-the-art Zr-based films. The findings are highly relevant for industrial treatments of aluminium surfaces, especially for those that undergo corrosion protection and painting process steps prior to usage.

Sulfur amino acids and alanine on pyrite (100) by X-ray photoemission spectroscopy: Surface or molecular role?

NASA Astrophysics Data System (ADS)

Sanchez-Arenillas, M.; Galvez-Martinez, S.; Mateo-Marti, E.

2017-08-01

This paper describes the first successful adsorption of the cysteine, cystine, methionine and alanine amino acids on the pyrite (100) surface under ultra-high vacuum conditions with crucial chemical adsorption parameters driving the process. We have demonstrated by X-ray photoemission spectroscopy (XPS) that the surface pretreatment annealing process on pyrite surfaces is a critical parameter driving surface reactivity. The presence of enriched monosulfide species on the pyrite (100) surface favours the amino acid NH2 chemical form, whereas a longer annealing surface pretreatment of over 3 h repairs the sulfur vacancies in the pyrite, enriching disulfide species on the pyrite surface, which promotes NH3+ adsorption due to the sulfur vacancies in the pyrite being replaced by sulfur atom dimers (S22-) on the surface. Furthermore, even if the surface chemistry (monosulfide or disulfide species enrichment) is the main factor promoting a partial conversion from NH2 to NH3+ species, the unique chemical structure of each amino acid provides a particular fingerprint in the process.

Plant interspecies competition for sunlight: a mathematical model of canopy partitioning.

PubMed

Nevai, Andrew L; Vance, Richard R

2007-07-01

We examine the influence of canopy partitioning on the outcome of competition between two plant species that interact only by mutually shading each other. This analysis is based on a Kolmogorov-type canopy partitioning model for plant species with clonal growth form and fixed vertical leaf profiles (Vance and Nevai in J. Theor. Biol., 2007, to appear). We show that canopy partitioning is necessary for the stable coexistence of the two competing plant species. We also use implicit methods to show that, under certain conditions, the species' nullclines can intersect at most once. We use nullcline endpoint analysis to show that when the nullclines do intersect, and in such a way that they cross, then the resulting equilibrium point is always stable. We also construct surfaces that divide parameter space into regions within which the various outcomes of competition occur, and then study parameter dependence in the locations of these surfaces. The analysis presented here and in a companion paper (Nevai and Vance, The role of leaf height in plant competition for sunlight: analysis of a canopy partitioning model, in review) together shows that canopy partitioning is both necessary and, under appropriate parameter values, sufficient for the stable coexistence of two hypothetical plant species whose structure and growth are described by our model.

Morphological and micromorphological characteristics of Desmodium fruits (Leguminosae: Papilionoideae).

PubMed

Freitas, Daiane M; Reis, Ademir; Bortoluzzi, Roseli L da Costa; Santos, Marisa

2014-12-01

The genus Desmodium is represented in Santa Catarina State, Brazil, by 13 species, all with lomen- taceous fruits. Shape, size and isthmus margin of loments vary, while the surface is glabrous, or covered by trichomes of different types. Morphological diversity of trichomes becomes particularly relevant to taxonomic description. The trichome types present on the surface of Desmodium fruits provide data for the identification and classification of species in the State. To assess this, three fruits of each species were collected and deposited at two herbaria, HBR and FLOR, in Santa Catarina, Brazil. Some rehydrated samples were examined using light microscopy (LM); and some sections were exposed to the following histochemical reagents: Sudan III for oils and Thionine for mucilage. The structural aspects of trichomes can be classified into uni- or multicellular and may still be simple, i.e., nonglandular or glandular. Using scanning electron microscopy (SEM), five types of trichomes were identified and analyzed among the Desmodium species studied: uncinate, uniseriate, globose multicellular, globose unicellular and subulate. Characteristics, such as loment margin and article form, glabrescent or pillous indument, trichome type, with or without papillous epidermal cells and epicuticular striations, showed relevant diagnostic value. An identification key was developed for Desmodium species from Santa Catarina State, Brazil, based on macro and micromorphological characters of the fruit.

Temporal response of a surface flashover on a velvet cathode in a relativistic diode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, J. E.; Moir, D. C.; Crawford, M. T.

2015-03-15

Surface flashover of a carbon fiber velvet cathode generates a discharge from which electrons are relativistically accelerated to γ ranging from 4.9 to 8.8 through a 17.8 cm diode. This discharge is assumed to be a hydrocarbon mixture. The principal objective of these experiments is to quantify the dynamics over the ∼100 ns pulse of the plasma discharge generated on the surface of the velvet cathode and across the anode-cathode (A-K) gap. A qualitative comparison of calculated and measured results is presented, which includes time resolved measurements with a photomultiplier tube and charge-coupled device images. In addition, initial visible spectroscopy measurements willmore » also be presented confirming the ion species are dominated by hydrogen.« less

Characterization of SeseC_01411 as a surface protective antigen of Streptococcus equi ssp. zooepidemicus.

PubMed

Xie, Honglin; Wei, Zigong; Ma, Chunquan; Li, Shun; Liu, Xiaohong; Fu, Qiang

2018-06-01

Streptococcus equi ssp. zooepidemicus (Streptococcus zooepidemicus, SEZ) is a commensal bacterium related to opportunistic infections of many species, including humans, dogs, cats, and pigs. SeseC_01411 has been proven to be immunogenic. However, its protective efficacy remained to be evaluated. In the present study, the purified recombinant SeseC_01411 could elicit a strong humoral antibody response and protect against lethal challenge with virulent SEZ in mice. Our finding confirmed that SeseC_01411 distributes on the surface of SEZ. In addition, the hyperimmune sera against SeseC_01411 could efficiently kill the bacteria in the phagocytosis test. The present study identified the immunogenic protein, SeseC_01411, as a novel surface protective antigen of SEZ. Copyright © 2018 Elsevier Ltd. All rights reserved.

Use of Raman microscopy and multivariate data analysis to observe the biomimetic growth of carbonated hydroxyapatite on bioactive glass.

PubMed

Seah, Regina K H; Garland, Marc; Loo, Joachim S C; Widjaja, Effendi

2009-02-15

In the present contribution, the biomimetic growth of carbonated hydroxyapatite (HA) on bioactive glass were investigated by Raman microscopy. Bioactive glass samples were immersed in simulated body fluid (SBF) buffered solution at pH 7.40 up to 17 days at 37 degrees C. Raman microscopy mapping was performed on the bioglass samples immersed in SBF solution for different periods of time. The collected data was then analyzed using the band-target entropy minimization technique to extract the observable pure component Raman spectral information. In this study, the pure component Raman spectra of the precursor amorphous calcium phosphate, transient octacalcium phosphate, and matured HA were all recovered. In addition, pure component Raman spectra of calcite, silica glass, and some organic impurities were also recovered. The resolved pure component spectra were fit to the normalized measured Raman data to provide the spatial distribution of these species on the sample surfaces. The current results show that Raman microscopy and multivariate data analysis provide a sensitive and accurate tool to characterize the surface morphology, as well as to give more specific information on the chemical species present and the phase transformation of phosphate species during the formation of HA on bioactive glass.

Pathways for Ethanol Dehydrogenation and Dehydration Catalyzed by Ceria (111) and (100) Surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beste, Ariana; Steven Overbury

2015-01-08

We have performed computations to better understand how surface structure affects selectivity in dehydrogenation and dehydration reactions of alcohols. Ethanol reactions on the (111) and (100) ceria surfaces were studied starting from the dominant surface species, ethoxy. We used DFT (PBE+U) to explore reaction pathways leading to ethylene and acetaldehyde and calculated estimates of rate constants employing transition state theory. To assess pathway contributions, we carried out kinetic analysis. Our results show that intermediate and transition state structures are stabilized on the (100) surface compared to the (111) surface. Formation of acetaldehyde over ethylene is kinetically and thermodynamically preferred onmore » both surfaces. Our results are consistent with temperature programmed surface reaction and steady-state experiments, where acetaldehyde was found as the main product and evidence was presented that ethylene formation at higher temperature originates from changes in adsorbate and surface structure.« less

Surface acidity scales: Experimental measurements of Brønsted acidities on anatase TiO2 and comparison with coinage metal surfaces

NASA Astrophysics Data System (ADS)

Silbaugh, Trent L.; Boaventura, Jaime S.; Barteau, Mark A.

2016-08-01

The first quantitative surface acidity scale for Brønsted acids on a solid surface is presented through the use of titration-displacement and equilibrium experiments on anatase TiO2. Surface acidities of species on TiO2 correlated with gas phase acidities, as was previously observed in qualitative studies of Brønsted acid displacement on Ag(110), Cu(110) and Au(111). A 90% compression of the surface acidity scale relative to the gas phase was observed due to compensation from the covalent component of the conjugate base - surface bond. Adsorbed conjugate bases need not be completely anionic for correlations with gas phase acidities to hold. Positive and negative substituent effects, such as substituted fluorine and hydrocarbon sidechain dispersion interactions with the surface, may modify the surface acidity scale, in agreement with previous experimental and theoretical work on Au(111).

Surface-Bound Intermediates in Low-Temperature Methanol Synthesis on Copper. Participants and Spectators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Yong; Mei, Donghai; Peden, Charles H.F.

The reactivity of surface adsorbed species present on copper catalysts during methanol synthesis at low temperatures was studied by simultaneous infrared spectroscopy (IR) and mass spectroscopy (MS) measurements during “titration” (transient surface reaction) experiments with isotopic tracing. The results show that adsorbed formate is a major bystander species present on the surface under steady-state methanol synthesis reaction conditions, but it cannot be converted to methanol by reaction with pure H 2, nor with H 2 plus added water. Formate-containing surface adlayers for these experiments were produced during steady state catalysis in (a) H 2:CO 2 (with substantial formate coverage) andmore » (b) moist H 2:CO (with no IR visible formate species). Both these reaction conditions produce methanol at steady state with relatively high rates. Adlayers containing formate were also produced by (c) formic acid adsorption. Various "titration" gases were used to probe these adlayers at modest temperatures (T = 410-450K) and 6 bar total pressure. Methanol gas (up to ~1% monolayer equivalent) was produced in "titration" from the H 2:CO 2 catalytic adlayers by H 2 plus water, but not by dry hydrogen. The decay in the formate IR features accelerated in the presence of added water vapor. The H 2:CO:H 2O catalytic adlayer produced similar methanol titration yields in H 2 plus water but showed no surface formate features in IR (less than 0.2% monolayer coverage). Finally, formate from formic acid chemisorption produced no methanol under any titration conditions. Even under (H 2:CO 2) catalytic reaction conditions, isotope tracing showed that pre-adsorbed formate from formic acid did not contribute to the methanol produced. Although non-formate intermediates exist during low temperature methanol synthesis on copper which can be converted to methanol gas by titration with pure H 2 plus water in sufficient quantities for that intermediate to be observable by IR, formate itself is only a "spectator" in this reaction and gives no observable methanol upon any titration we performed with H 2 or H 2 plus water.« less

Effects of sulfate ligand on uranyl carbonato surface species on ferrihydrite surfaces

USGS Publications Warehouse

Arai, Yuji; Fuller, C.C.

2012-01-01

Understanding uranium (U) sorption processes in permeable reactive barriers (PRB) are critical in modeling reactive transport for evaluating PRB performance at the Fry Canyon demonstration site in Utah, USA. To gain insight into the U sequestration mechanism in the amorphous ferric oxyhydroxide (AFO)-coated gravel PRB, U(VI) sorption processes on ferrihydrite surfaces were studied in 0.01 M Na2SO4 solutions to simulate the major chemical composition of U-contaminatedgroundwater (i.e., [SO42-]~13 mM L-1) at the site. Uranyl sorption was greater at pH 7.5 than that at pH 4 in both air- and 2% pCO2-equilibrated systems. While there were negligible effects of sulfate ligands on the pH-dependent U(VI) sorption (<24 h) in both systems, X-ray absorption spectroscopy (XAS) analysis showed sulfate ligand associated U(VI) surface species at the ferrihydrite–water interface. In air-equilibrated systems, binary and mono-sulfate U(VI) ternary surface species co-existed at pH 5.43. At pH 6.55–7.83, a mixture of mono-sulfate and bis-carbonato U(VI) ternary surface species became more important. At 2% pCO2, there was no contribution of sulfate ligands on the U(VI) ternary surface species. Instead, a mixture of bis-carbonato inner-sphere (38%) and tris-carbonato outer-sphere U(VI) ternary surface species (62%) was found at pH 7.62. The study suggests that the competitive ligand (bicarbonate and sulfate) coordination on U(VI) surface species might be important in evaluating the U solid-state speciation in the AFO PRB at the study site where pCO2 fluctuates between 1 and 2 pCO2%.

Effects of sulfate ligand on uranyl carbonato surface species on ferrihydrite surfaces.

PubMed

Arai, Yuji; Fuller, C C

2012-01-01

Understanding uranium (U) sorption processes in permeable reactive barriers (PRB) are critical in modeling reactive transport for evaluating PRB performance at the Fry Canyon demonstration site in Utah, USA. To gain insight into the U sequestration mechanism in the amorphous ferric oxyhydroxide (AFO)-coated gravel PRB, U(VI) sorption processes on ferrihydrite surfaces were studied in 0.01 M Na(2)SO(4) solutions to simulate the major chemical composition of U-contaminated groundwater (i.e., [SO(4)(2-)] ~13 mM L(-1)) at the site. Uranyl sorption was greater at pH 7.5 than that at pH 4 in both air- and 2% pCO(2)-equilibrated systems. While there were negligible effects of sulfate ligands on the pH-dependent U(VI) sorption (<24 h) in both systems, X-ray absorption spectroscopy (XAS) analysis showed sulfate ligand associated U(VI) surface species at the ferrihydrite-water interface. In air-equilibrated systems, binary and mono-sulfate U(VI) ternary surface species co-existed at pH 5.43. At pH 6.55-7.83, a mixture of mono-sulfate and bis-carbonato U(VI) ternary surface species became more important. At 2% pCO(2), there was no contribution of sulfate ligands on the U(VI) ternary surface species. Instead, a mixture of bis-carbonato inner-sphere (38%) and tris-carbonato outer-sphere U(VI) ternary surface species (62%) was found at pH 7.62. The study suggests that the competitive ligand (bicarbonate and sulfate) coordination on U(VI) surface species might be important in evaluating the U solid-state speciation in the AFO PRB at the study site where pCO(2) fluctuates between 1 and 2 pCO(2)%. Copyright © 2011 Elsevier Inc. All rights reserved.

3-D Topo Surface Visualization of Acid-Base Species Distributions: Corner Buttes, Corner Pits, Curving Ridge Crests, and Dilution Plains

ERIC Educational Resources Information Center

Smith, Garon C.; Hossain, Md Mainul

2017-01-01

Species TOPOS is a free software package for generating three-dimensional (3-D) topographic surfaces ("topos") for acid-base equilibrium studies. This upgrade adds 3-D species distribution topos to earlier surfaces that showed pH and buffer capacity behavior during titration and dilution procedures. It constructs topos by plotting…

Conservation of myeloid surface antigens on primate granulocytes.

PubMed

Letvin, N L; Todd, R F; Palley, L S; Schlossman, S F; Griffin, J D

1983-02-01

Monoclonal antibodies reactive with myeloid cell surface antigens were used to study evolutionary changes in granulocyte surface antigens from primate species. Certain of these granulocyte membrane antigens are conserved in phylogenetically distant species, indicating the potential functional importance of these structures. The degree of conservation of these antigens reflects the phylogenetic relationship between primate species. Furthermore, species of the same genus show similar patterns of binding to this panel of anti-human myeloid antibodies. This finding of conserved granulocyte surface antigens suggests that non-human primates may provide a model system for exploring uses of monoclonal antibodies in the treatment of human myeloid disorders.

Investigating the Interaction of Water Vapour with Aminopropyl Groups on the Surface of Mesoporous Silica Nanoparticles.

PubMed

Paul, Geo; Musso, Giorgia Elena; Bottinelli, Emanuela; Cossi, Maurizio; Marchese, Leonardo; Berlier, Gloria

2017-04-05

The interaction of water molecules with the surface of hybrid silica-based mesoporous materials is studied by 29 Si, 1 H and 13 C solid-state NMR and IR spectroscopy, with the support of ab initio calculations. The surface of aminopropyl-grafted mesoporous silica nanoparticles is studied in the dehydrated state and upon interaction with controlled doses of water vapour. Former investigations described the interactions between aminopropyl and residual SiOH groups; the present study shows the presence of hydrogen-bonded species (SiOH to NH 2 ) and weakly interacting "free" aminopropyl chains with restricted mobility, together with a small amount of protonated NH 3 + groups. The concentration of the last-named species increased upon interaction with water, and this indicates reversible and fast proton exchange from water molecules to a fraction of the amino groups. Herein, this is discussed and explained for the first time, by a combination of experimental and theoretical approaches. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chemical Evolution of a Protoplanetary Disk

NASA Astrophysics Data System (ADS)

Semenov, Dmitry A.

2011-12-01

In this paper we review recent progress in our understanding of the chemical evolution of protoplanetary disks. Current observational constraints and theoretical modeling on the chemical composition of gas and dust in these systems are presented. Strong variations of temperature, density, high-energy radiation intensities in these disks, both radially and vertically, result in a peculiar disk chemical structure, where a variety of processes are active. In hot, dilute and heavily irradiated atmosphere only the most photostable simple radicals and atoms and atomic ions exist, formed by gas-phase processes. Beneath the atmosphere a partly UV-shielded, warm molecular layer is located, where high-energy radiation drives rich ion-molecule and radical-radical chemistry, both in the gas phase and on dust surfaces. In a cold, dense, dark disk midplane many molecules are frozen out, forming thick icy mantles where surface chemistry is active and where complex polyatomic (organic) species are synthesized. Dynamical processes affect disk chemical composition by enriching it in abundances of complex species produced via slow surface processes, which will become detectable with ALMA.

Advanced nutrient removal from surface water by a consortium of attached microalgae and bacteria: A review.

PubMed

Liu, Junzhuo; Wu, Yonghong; Wu, Chenxi; Muylaert, Koenraad; Vyverman, Wim; Yu, Han-Qing; Muñoz, Raúl; Rittmann, Bruce

2017-10-01

Innovative and cost-effective technologies for advanced nutrient removal from surface water are urgently needed for improving water quality. Conventional biotechnologies, such as ecological floating beds, or constructed wetlands, are not effective in removing nutrients present at low-concentration. However, microalgae-bacteria consortium is promising for advanced nutrient removal from wastewater. Suspended algal-bacterial systems can easily wash out unless the hydraulic retention time is long, attached microalgae-bacteria consortium is more realistic. This critical review summarizes the fundamentals and status of attached microalgae-bacteria consortium for advanced nutrient removal from surface water. Key advantages are the various nutrient removal pathways, reduction of nutrients to very low concentration, and diversified photobioreactor configurations. Challenges include poor identification of functional species, poor control of the community composition, and long start-up times. Future research should focus on the selection and engineering of robust microbial species, mathematical modelling of the composition and functionality of the consortium, and novel photobioreactor configurations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Triangular Diagrams Teach Steady and Dynamic Behaviour of Catalytic Reactions.

ERIC Educational Resources Information Center

Klusacek, K.; And Others

1989-01-01

Illustrates how triangular diagrams can aid in presenting some of the rather complex transient interactions that occur among gas and surface species during heterogeneous catalytic reactions. The basic equations and numerical examples are described. Classroom use of the triangular diagram is discussed. Several diagrams and graphs are provided. (YP)

Atomic Oxygen Textured Polymers

NASA Technical Reports Server (NTRS)

Banks, Bruce A.; Rutledge, Sharon K.; Hunt, Jason D.; Drobotij, Erin; Cales, Michael R.; Cantrell, Gidget

1995-01-01

Atomic oxygen can be used to microscopically alter the surface morphology of polymeric materials in space or in ground laboratory facilities. For polymeric materials whose sole oxidation products are volatile species, directed atomic oxygen reactions produce surfaces of microscopic cones. However, isotropic atomic oxygen exposure results in polymer surfaces covered with lower aspect ratio sharp-edged craters. Isotropic atomic oxygen plasma exposure of polymers typically causes a significant decrease in water contact angle as well as altered coefficient of static friction. Such surface alterations may be of benefit for industrial and biomedical applications. The results of atomic oxygen plasma exposure of thirty-three (33) different polymers are presented, including typical morphology changes, effects on water contact angle, and coefficient of static friction.

The cold and atmospheric-pressure air surface barrier discharge plasma for large-area sterilization applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Dacheng; Department of Aeronautics, Fujian Key Laboratory for Plasma and Magnetic Resonance, School of Physics and Mechanical and Electrical Engineering, Xiamen University, Xiamen, Fujian 361005; Zhao Di

2011-04-18

This letter reports a stable air surface barrier discharge device for large-area sterilization applications at room temperature. This design may result in visually uniform plasmas with the electrode area scaled up (or down) to the required size. A comparison for the survival rates of Escherichia coli from air, N{sub 2} and O{sub 2} surface barrier discharge plasmas is presented, and the air surface plasma consisting of strong filamentary discharges can efficiently kill Escherichia coli. Optical emission measurements indicate that reactive species such as O and OH generated in the room temperature air plasmas play a significant role in the sterilizationmore » process.« less

The MiiA motif is a common marker present in polytopic surface proteins of oral and urinary tract invasive bacteria.

PubMed

Martín-Galiano, Antonio J

2017-04-01

Many surface virulence factors of bacterial pathogens show mosaicism and confounding phylogenetic origin. The Streptococcus gordonii platelet-binding GspB protein, the Streptococcus sanguinis SrpA adhesin and the Streptococcus pneumoniae DiiA protein, share an imperfect 27-residue motif. Given the disparate domain architectures of these proteins and its association to invasive disease, this motif was named MiiA from Multiarchitecture invasion-involved motif A. MiiA is predicted to adopt a beta-sheet folding, probably related to the Ig-like fold, with a symmetrical positioning of two conserved aspartic residues. A specific hidden Markov model profiling MiiA was built, which specifically detected the motif in proteins from 58 species, mainly in cell-wall proteins from Gram-positive bacteria. These proteins contained one to ten MiiA motifs, which were embedded within larger repeat units of 70-82 residues. MiiA motifs combined to other domains and elements such as coiled-coils and low-complexity regions. The species carrying MiiA-proteins included commensals from the urogenital tract and the oral cavity, which can cause opportunistic endocarditis and sepsis. Intra-protein MiiA repeats showed a complex mixture of orthologal, paralogal and inter-species relationships, suggestive of a multistep origin. Presence of these repeats in proteins involved in oligosaccharide recognition and lifestyle of species suggest a putative function for MiiA repeats in sugars binding, probably those present in receptors of epithelial and blood cells. MiiA modules appear to have been transferred horizontally between species co-habiting in the same niche to create their own MiiA-containing determinants. The present work provides a global study and a catalog of potential MiiA virulence factors that should be analyzed experimentally. Copyright © 2017 Elsevier B.V. All rights reserved.

Chemical treatment for silica-containing glass surfaces

DOEpatents

Grabbe, Alexis; Michalske, Terry Arthur; Smith, William Larry

1999-01-01

Dehydroxylated, silica-containing, glass surfaces are known to be at least partially terminated by strained siloxane rings. According to the invention, a surface of this kind is exposed to a selected silane compound or mixture of silane compounds under reaction-promoting conditions. The ensuing reaction results in opening of the strained siloxane rings, and termination of surface atoms by chemical species, such as organic or organosilicon species, having desirable properties. These species can be chosen to provide qualities such as hydrophobicity, or improved coupling to a polymeric coating.

Chemical treatment for silica-containing glass surfaces

DOEpatents

Grabbe, Alexis; Michalske, Terry Arthur; Smith, William Larry

1998-01-01

Dehydroxylated, silica-containing, glass surfaces are known to be at least partially terminated by strained siloxane rings. According to the invention, a surface of this kind is exposed to a selected silane compound or mixture of silane compounds under reaction-promoting conditions. The ensuing reaction results in opening of the strained siloxane rings, and termination of surface atoms by chemical species, such as organic or organosilicon species, having desirable properties. These species can be chosen to provide qualities such as hydrophobicity, or improved coupling to a polymeric coating.

Chemical treatment for silica-containing glass surfaces

DOEpatents

Grabbe, Alexis; Michalske, Terry Arthur; Smith, William Larry

1999-01-01

Dehydroxylated, silica-containing, glass surfaces are known to be at least partially terminated by strained siloxane rings. According to the invention, a surface of this kind is exposed to a selected silane compound or mixture of silane compounds under reaction-promoting conditons. The ensuing reaction results in opening of the strained siloxane rings, and termination of surface atoms by chemical species, such as organic or organosilicon species, having desirable properties. These species can be chosen to provide qualities such as hydrophobicity, or improved coupling to a polymeric coating.

Aqueous reactive species induced by a PCB surface micro-discharge air plasma device: a quantitative study

NASA Astrophysics Data System (ADS)

Chen, Chen; Li, Fanying; Chen, Hai-Lan; Kong, Michael G.

2017-11-01

This paper presents a quantitative investigation on aqueous reactive species induced by air plasma generated from a printed circuit board surface micro-discharge (SMD) device. Under the conditions amenable for proliferation of mammalian cells, concentrations of ten types of reactive oxygen and nitrogen species (RONS) in phosphate buffering solution (PBS) are measured by chemical fluorescent assays and electron spin resonance spectroscopy (ESR). Results show that concentrations of several detected RNS (NO2- , NO3- , peroxynitrites, and NO2\\centerdot ) are higher than those of ROS (H2O2, O2\\centerdot - , and 1O2) in the air plasma treated solution. Concentrations of NO3- can reach 150 times of H2O2 with 60 s plasma treatment. For short-lived species, the air plasma generates more copious peroxynitrite than other RONS including NO2\\centerdot , O2\\centerdot - , 1O2, and N{{O}\\centerdot } in PBS. In addition, the existence of reaction between H2O2 and NO2- /HNO2 to produce peroxynitrite is verified by the chemical scavenger experiments. The reaction relations between detected RONS are also discussed.

Differences in surfactant lipids collected from pleural and pulmonary lining fluids.

PubMed

Mills, Paul C; Chen, Yi; Hills, Yvette C; Hills, Brian A

2005-11-01

The type and relative importance of saturated and unsaturated phospholipid components of surfactant within the epithelial lining fluid (ELF) of the inner and outer surfaces of the lung is not known. Seven healthy dogs were anesthetized and a bronchoalveolar lavage (BAL) was performed, immediately followed by a pleural lavage (PL). Lipid was extracted from lavage fluid and then analyzed for saturated, primarily dipalmitoylphosphatidylcholine (DPPC), and unsaturated phosphatidylcholine (PC) species using high-performance liquid chromatography (HPLC) with combined fluorescence and ultraviolet detection. Dilution of ELF in lavage fluids was corrected for using the urea method. DPPC (494.7 +/- 213.9 microg/mL) was the predominant PC present in ELF collected from the alveolar surface. In contrast, significantly higher (p = 0.028) proportions of unsaturated PC species were measured in PL fluid (approximately 105 microg/mL), particularly stearoyl-linoleoyl-phosphatidylcholine (SLPC), which could not be measured in fluid collected from the alveoli, compared to DPPC (2.6 +/- 2.0 microg/mL). This study indicates that unsaturated PC species seem to be more important than saturated species, particularly DPPC, in the pleural cavity, which has implications for surfactant replenishment following pleural disease or thoracic surgery.

A new species of Brevianthus (Brevianthaceae, Marchantiophyta) from New Caledonia with unusual underleaf production.

PubMed

Renner, Matt A M; Engel, John J; Patzak, Simon D F; Heinrichs, Jochen

2015-01-01

Brevianthus is a distinctive genus of leafy liverwort in its succubously inserted, entire leaves, lack of underleaves, restriction of sexual organs to lateral-intercalary branches, scattered rhizoids and dense leaf-surface ornamentation. The sole species, Brevianthusflavus, is divided into two subspecies, one in Tasmania the other in New Zealand. A second species, Brevianthushypocanthidium, is described as new and is the first record of the genus for New Caledonia. Among its distinguishing characters are its shallowly bilobed leaves, and triangular underleaves present on small to medium-sized shoot sectors, the lack of a hyaline leaf margin, and the crenulate leaf margin formed by heavily thickened external cell walls. The most unusual features of the new species are the presence of underleaves between lateral leaf insertion lines that reach the ventral stem mid-line, and the absence of underleaves from larger shoots. To explain these features we propose a competitive model of shoot formation wherein the ventral merophyte progressively loses vigor as its relative stature decreases, and its derivative cells become discontinuous and isolated along the ventral stem surface, with intervening areas occupied by derivatives of the more vigorous lateral merophytes.

Biochemical evolution. I. Polymerization on internal, organophilic silica surfaces of dealuminated zeolites and feldspars

PubMed Central

Smith, Joseph V.

1998-01-01

Catalysis at mineral surfaces might generate replicating biopolymers from simple chemicals supplied by meteorites, volcanic gases, and photochemical gas reactions. Many ideas are implausible in detail because the proposed mineral surfaces strongly prefer water and other ionic species to organic ones. The molecular sieve silicalite (Union Carbide; = Al-free Mobil ZSM-5 zeolite) has a three-dimensional, 10-ring channel system whose electrically neutral Si-O surface strongly adsorbs organic species over water. Three -O-Si tetrahedral bonds lie in the surface, and the fourth Si-O points inwards. In contrast, the outward Si-OH of simple quartz and feldspar crystals generates their ionic organophobicity. The ZSM-5-type zeolite mutinaite occurs in Antarctica with boggsite and tschernichite (Al-analog of Mobil Beta). Archean mutinaite might have become de-aluminated toward silicalite during hot/cold/wet/dry cycles. Catalytic activity of silicalite increases linearly with Al-OH substitution for Si, and Al atoms tend to avoid each other. Adjacent organophilic and catalytic Al-OH regions in nanometer channels might have scavenged organic species for catalytic assembly into specific polymers protected from prompt photochemical destruction. Polymer migration along weathered silicic surfaces of micrometer-wide channels of feldspars might have led to assembly of replicating catalytic biomolecules and perhaps primitive cellular organisms. Silica-rich volcanic glasses should have been abundant on the early Earth, ready for crystallization into zeolites and feldspars, as in present continental basins. Abundant chert from weakly metamorphosed Archaean rocks might retain microscopic clues to the proposed mineral adsorbent/catalysts. Other framework silicas are possible, including ones with laevo/dextro one-dimensional channels. Organic molecules, transition-metal ions, and P occur inside modern feldspars. PMID:9520372

Biochemical evolution. I. Polymerization On internal, organophilic silica surfaces of dealuminated zeolites and feldspars.

PubMed

Smith, J V

1998-03-31

Catalysis at mineral surfaces might generate replicating biopolymers from simple chemicals supplied by meteorites, volcanic gases, and photochemical gas reactions. Many ideas are implausible in detail because the proposed mineral surfaces strongly prefer water and other ionic species to organic ones. The molecular sieve silicalite (Union Carbide; = Al-free Mobil ZSM-5 zeolite) has a three-dimensional, 10-ring channel system whose electrically neutral Si-O surface strongly adsorbs organic species over water. Three -O-Si tetrahedral bonds lie in the surface, and the fourth Si-O points inwards. In contrast, the outward Si-OH of simple quartz and feldspar crystals generates their ionic organophobicity. The ZSM-5-type zeolite mutinaite occurs in Antarctica with boggsite and tschernichite (Al-analog of Mobil Beta). Archean mutinaite might have become de-aluminated toward silicalite during hot/cold/wet/dry cycles. Catalytic activity of silicalite increases linearly with Al-OH substitution for Si, and Al atoms tend to avoid each other. Adjacent organophilic and catalytic Al-OH regions in nanometer channels might have scavenged organic species for catalytic assembly into specific polymers protected from prompt photochemical destruction. Polymer migration along weathered silicic surfaces of micrometer-wide channels of feldspars might have led to assembly of replicating catalytic biomolecules and perhaps primitive cellular organisms. Silica-rich volcanic glasses should have been abundant on the early Earth, ready for crystallization into zeolites and feldspars, as in present continental basins. Abundant chert from weakly metamorphosed Archaean rocks might retain microscopic clues to the proposed mineral adsorbent/catalysts. Other framework silicas are possible, including ones with laevo/dextro one-dimensional channels. Organic molecules, transition-metal ions, and P occur inside modern feldspars.

Surveillance of bacterial contamination in small animal veterinary hospitals with special focus on antimicrobial resistance and virulence traits of enterococci.

PubMed

KuKanich, Kate S; Ghosh, Anuradha; Skarbek, Jennifer V; Lothamer, Kale M; Zurek, Ludek

2012-02-15

To determine the prevalence of bacterial contamination on 4 surfaces of 4 types of standard equipment in small animal veterinary hospitals. Surveillance study. 10 small animal veterinary hospitals. Each hospital was visited 3 times at 4-month intervals; at each visit, a cage door, stethoscope, rectal thermometer, and mouth gag were swabbed. Swab samples were each plated onto media for culture of enterococci and organisms in the family Enterobacteriaceae. Enterococci were identified via a species-specific PCR assay and sodA gene sequencing; species of Enterobacteriaceae were identified with a biochemical test kit. Antimicrobial susceptibility was assessed via the disk diffusion method. Enterococci were screened for virulence traits and genotyped to assess clonality. Among the 10 hospitals, enterococci were isolated from cage doors in 7, from stethoscopes in 7, from thermometers in 6, and from mouth gags in 1; contamination with species of Enterobacteriaceae was rare. Enterococci were mainly represented by Enterococcus faecium (35.4%), Enterococcus faecalis (33.2%), and Enterococcus hirae (28.3%). Antimicrobial resistance was common in E. faecium, whereas virulence traits were present in 99% of E. faecalis isolates but not in E. faecium isolates. Clonal multidrug-resistant E. faecium was isolated from several surfaces at 1 hospital over multiple visits, whereas sporadic nonclonal contamination was detected in other hospitals. Contamination of surfaces in small animal veterinary hospitals with multidrug-resistant enterococci is a potential concern for pets and humans contacting these surfaces. Implementing precautions to minimize enterococcal contamination on these surfaces is recommended.

Trabecular architecture in the sciuromorph femoral head: allometry and functional adaptation.

PubMed

Mielke, Maja; Wölfer, Jan; Arnold, Patrick; van Heteren, Anneke H; Amson, Eli; Nyakatura, John A

2018-01-01

Sciuromorpha (squirrels and close relatives) are diverse in terms of body size and locomotor behavior. Individual species are specialized to perform climbing, gliding or digging behavior, the latter being the result of multiple independent evolutionary acquisitions. Each lifestyle involves characteristic loading patterns acting on the bones of sciuromorphs. Trabecular bone, as part of the bone inner structure, adapts to such loading patterns. This network of thin bony struts is subject to bone modeling, and therefore reflects habitual loading throughout lifetime. The present study investigates the effect of body size and lifestyle on trabecular structure in Sciuromorpha. Based upon high-resolution computed tomography scans, the femoral head 3D inner microstructure of 69 sciuromorph species was analyzed. Species were assigned to one of the following lifestyle categories: arboreal, aerial, fossorial and semifossorial. A cubic volume of interest was selected in the center of each femoral head and analyzed by extraction of various parameters that characterize trabecular architecture (degree of anisotropy, bone volume fraction, connectivity density, trabecular thickness, trabecular separation, bone surface density and main trabecular orientation). Our analysis included evaluation of the allometric signals and lifestyle-related adaptation in the trabecular parameters. We show that bone surface density, bone volume fraction, and connectivity density are subject to positive allometry, and degree of anisotropy, trabecular thickness, and trabecular separation to negative allometry. The parameters connectivity density, bone surface density, trabecular thickness, and trabecular separation show functional signals which are related to locomotor behavior. Aerial species are distinguished from fossorial ones by a higher trabecular thickness, lower connectivity density and lower bone surface density. Arboreal species are distinguished from semifossorial ones by a higher trabecular separation. This study on sciuromorph trabeculae supplements the few non-primate studies on lifestyle-related functional adaptation of trabecular bone. We show that the architecture of the femoral head trabeculae in Sciuromorpha correlates with body mass and locomotor habits. Our findings provide a new basis for experimental research focused on functional significance of bone inner microstructure.

Surface area effects on the reduction of U VI in the presence of synthetic montmorillonite

DOE PAGES

Boyanov, Maxim I.; Latta, Drew E.; Scherer, Michelle M.; ...

2016-12-14

Here, the redox transformations that affect the environmental mobility of metal or radionuclide contaminants typically take place in the presence of mineral or biological surfaces. Adsorption can alter the speciation and free energy of a dissolved ion and can thus change the occurrence, rate, or products of redox reactions relative to those expected in homogenous solution. Here, we investigated the effect of SYn-1, a redox-inactive synthetic montomorillonite clay mineral, on the reduction of U VI by dihydroanthraquinone-2,6 disulfonate (AH 2QDS, the reduced form of the soluble electron shuttle AQDS). We varied the surface:U ratio in a circumneutral bicarbonate solution andmore » measured the valence and atomic coordination of U in the solids using X-ray absorption spectroscopy (XANES and EXAFS). The spectra show that U IV was the predominant product both in the presence or absence of the clay mineral, indicating that adsorption of U VI to clay mineral surface sites does not affect its ability to be reduced by AH 2QDS. In the absence of the clay mineral and at low-to-intermediate surface:U ratios the predominant UIV product was nanoparticulate uraninite, UO 2. At the highest surface:U ratio tested (100 g/L clay mineral and 50 μM U) we observe a decrease in the proportion of uraninite down to 50%, with the remaining U IV present as adsorbed, non-uraninite species. These results are similar to previous findings with magnetite and rutile, where adsorbed U IV were the predominant species below a specific surface coverage and U in excess of this coverage was precipitated as uraninite. The threshold coverage determined here for the SYn-1 clay mineral is 10-100 × lower than that determined for magnetite and rutile, suggesting that clay mineral surfaces may be less important than metal oxides for stabilizing non-uraninite U IV species in natural sediments.« less

Surface area effects on the reduction of U VI in the presence of synthetic montmorillonite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyanov, Maxim I.; Latta, Drew E.; Scherer, Michelle M.

Here, the redox transformations that affect the environmental mobility of metal or radionuclide contaminants typically take place in the presence of mineral or biological surfaces. Adsorption can alter the speciation and free energy of a dissolved ion and can thus change the occurrence, rate, or products of redox reactions relative to those expected in homogenous solution. Here, we investigated the effect of SYn-1, a redox-inactive synthetic montomorillonite clay mineral, on the reduction of U VI by dihydroanthraquinone-2,6 disulfonate (AH 2QDS, the reduced form of the soluble electron shuttle AQDS). We varied the surface:U ratio in a circumneutral bicarbonate solution andmore » measured the valence and atomic coordination of U in the solids using X-ray absorption spectroscopy (XANES and EXAFS). The spectra show that U IV was the predominant product both in the presence or absence of the clay mineral, indicating that adsorption of U VI to clay mineral surface sites does not affect its ability to be reduced by AH 2QDS. In the absence of the clay mineral and at low-to-intermediate surface:U ratios the predominant UIV product was nanoparticulate uraninite, UO 2. At the highest surface:U ratio tested (100 g/L clay mineral and 50 μM U) we observe a decrease in the proportion of uraninite down to 50%, with the remaining U IV present as adsorbed, non-uraninite species. These results are similar to previous findings with magnetite and rutile, where adsorbed U IV were the predominant species below a specific surface coverage and U in excess of this coverage was precipitated as uraninite. The threshold coverage determined here for the SYn-1 clay mineral is 10-100 × lower than that determined for magnetite and rutile, suggesting that clay mineral surfaces may be less important than metal oxides for stabilizing non-uraninite U IV species in natural sediments.« less

Antimony leaching and chemical species analyses in an industrial solid waste: Surface and bulk speciation using ToF-SIMS and XANES.

PubMed

Kappen, P; Ferrando-Miguel, G; Reichman, S M; Innes, L; Welter, E; Pigram, P J

2017-05-05

The surface chemistry and bulk chemical speciation of solid industrial wastes containing 8wt-% antimony (Sb) were investigated using synchrotron X-ray Absorption Near Edge Structure (XANES) and Time-of-Flight Ion Secondary Mass Spectrometry (ToF-SIMS). Leaching experiments were conducted in order to better understand the behavior of Sb in waste streams and to inform regulatory management of antimony-containing wastes. The experiments also demonstrate how a combination of XANES and ToF-SIMS adds value to the field of waste investigations. Leaching treatments (acid and base) were performed at a synchrotron over 24h time periods. Surface analyses of the wastes before leaching showed the presence of Sb associated with S and O. Bulk analyses revealed Sb to be present, primarily, as trivalent sulfide species. Both acid and base leaching did not change the antimony speciation on the solid. Leaching transferred about 1% of the total Sb into solution where Sb was found to be present as Sb(V). XANES data showed similarities between leachate and FeSbO 4 . During base leaching, the Sb content in solution gradually increased over time, and potential desorption mechanisms are discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Collisional quenching of atoms and molecules on spacecraft thermal protection surfaces

NASA Technical Reports Server (NTRS)

Marinelli, W. J.; Green, B. D.

1988-01-01

Preliminary results of a research program to determine energy partitioning in spacecraft thermal protection materials due to atom recombination at the gas-surface interface are presented. The primary focus of the research is to understand the catalytic processes which determine heat loading on Shuttle, Aeroassisted OTV, and NASP thermal protection surfaces in nonequilibrium flight regimes. Highly sensitive laser diagnostics based on laser-induced fluorescence and resonantly-enhanced multiphoton ionization spectroscopy are used to detect atoms and metastable molecules. At low temperatures, a discharge flow reactor is employed to measure deactivation/recombination coefficients for O-atoms, N-atoms, and O2. Detection methods are presented for measuring O-atoms, O2 and N2, and results for deactivation of O2 and O-atoms on reaction-cured glass and Ni surfaces. Both atom recombination and metastable product formation are examined. Radio-frequency discharges are used to produce highly dissociated beams of atomic species at energies characteristic of the surface temperature. Auger electron spectroscopy is employed as a diagnostic of surface composition in order to accurately define and control measurement conditions.

Multi-species coral Sr/Ca-based sea-surface temperature reconstruction using Orbicella faveolata and Siderastrea siderea from the Florida Straits

USGS Publications Warehouse

Flannery, Jennifer A.; Richey, Julie N.; Thirumalai, Kaustubh; Poore, Richard Z.; DeLong, Kristine L.

2017-01-01

We present new, monthly-resolved Sr/Ca-based sea-surface temperature (SST) records from two species of massive coral, Orbicella faveolata and Siderastrea siderea, from the Dry Tortugas National Park, FL, USA (DTNP). We combine these new records with published data from three additional S. siderea coral colonies to generate a 278-year long multi-species stacked Sr/Ca-SST record from DTNP. The composite record of mean annual Sr/Ca-SST at DTNP shows pronounced decadal-scale variability with a range of 1 to 2°C. Notable cool intervals in the Sr/Ca-derived SST lasting about a decade centered at ~1845, ~1935, and ~1965 are associated with reduced summer Sr/Ca-SST (monthly maxima < 29°C), and imply a reduction in the spatial extent of the Atlantic Warm Pool (AWP). There is significant coherence between the composite DTNP Sr/Ca-SST record and the Atlantic Multidecadal Oscillation (AMO) index, with the AMO lagging Sr/Ca-SST at DTNP by 9 years. Low frequency variability in the Gulf Stream surface transport, which originates near DTNP, may provide a link for the lagged relationship between multidecadal variability at DTNP and the AMO.

Caesium isothermal migration behaviour in sintered titanium nitride: New data and comparison with previous results on iodine and xenon

NASA Astrophysics Data System (ADS)

Gavarini, S.; Bès, R.; Peaucelle, C.; Martin, P.; Esnouf, C.; Toulhoat, N.; Cardinal, S.; Moncoffre, N.; Malchère, A.; Garnier, V.; Millard-Pinard, N.; Guipponi, C.

2009-06-01

Titanium nitride has been proposed as a fission product barrier in fuel structures for gas cooled fast reactor (GFR) systems. The thermal migration of Cs was studied by implanting 800 keV 133Cs ++ ions into sintered samples of TiN at an ion fluence of 5 × 10 15 cm -2. Thermal treatments at temperatures ranging from 1500 to 1650 °C were performed under a secondary vacuum. Concentration profiles were determined by 2.5 MeV 4He + elastic backscattering. The results reveal that the global mobility of caesium in the host matrix is low compared to xenon and iodine implanted in the same conditions. Nevertheless, the evolution of caesium depth profile during thermal treatment presents similarities with that of xenon. Both species are homogeneously transported towards the surface and the transport rate increases with the temperature. In comparison, iodine exhibits singular migration behaviour. Several assumptions are proposed to explain the better retention of caesium in comparison with both other species. The potential role played by the oxidation is underlined since even a slight modification of the surface stoichiometry may modify species mobility. More generally, the apparition of square-like shapes on the surface of the samples after implantations and thermal treatments is discussed.

Transport properties associated with carbon-phenolic ablators

NASA Technical Reports Server (NTRS)

Biolsi, L.

1982-01-01

Entry vehicle heat shields designed for entry into the atmosphere of the outer planets are usually made of carbonaceous material such as carbon-phenolic ablator. Ablative injection of this material is an important mechanism for reducing the heat at the surface of the entry vehicle. Conductive transport properties in the shock layer are important for some entry conditions. The kinetic theory of gases has been used to calculate the transport properties for 17 gaseous species obtained from the ablation of carbon-phenolic heat shields. Results are presented for the pure species and for the gas mixture.

Method for in-situ cleaning of carbon contaminated surfaces

DOEpatents

Klebanoff, Leonard E.; Grunow, Philip; Graham, Jr., Samuel

2006-12-12

Activated gaseous species generated adjacent a carbon contaminated surface affords in-situ cleaning. A device for removing carbon contamination from a surface of the substrate includes (a) a housing defining a vacuum chamber in which the substrate is located; (b) a source of gaseous species; and (c) a source of electrons that are emitted to activate the gaseous species into activated gaseous species. The source of electrons preferably includes (i) a filament made of a material that generates thermionic electron emissions; (ii) a source of energy that is connected to the filament; and (iii) an electrode to which the emitted electrons are attracted. The device is particularly suited for photolithography systems with optic surfaces, e.g., mirrors, that are otherwise inaccessible unless the system is dismantled. A method of removing carbon contaminants from a substrate surface that is housed within a vacuum chamber is also disclosed. The method employs activated gaseous species that react with the carbon contaminants to form carbon containing gaseous byproducts.

GEOSURF: a computer program for modeling adsorption on mineral surfaces from aqueous solution

NASA Astrophysics Data System (ADS)

Sahai, Nita; Sverjensky, Dimitri A.

1998-11-01

A new program, GEOSURF, has been developed for calculating aqueous and surface speciation consistent with the triple-layer model of surface complexation. GEOSURF is an extension of the original programs MINEQL, MICROQL and HYDRAQL. We present, here, the basic algorithm of GEOSURF along with a description of the new features implemented. GEOSURF is linked to internally consistent data bases for surface species (SURFK.DAT) and for aqueous species (AQSOL.DAT). SURFK.DAT contains properties of minerals such as site densities, and equilibrium constants for adsorption of aqueous protons and electrolyte ions on a variety of oxides and hydroxides. The Helgeson, Kirkham and Flowers version of the extended Debye-Huckel Equation for 1:1 electrolytes is implemented for calculating aqueous activity coefficients. This permits the calculation of speciation at ionic strengths greater than 0.5 M. The activity of water is computed explicitly from the osmotic coefficient of the solution, and the total amount of electrolyte cation (or anion) is adjusted to satisfy the electroneutrality condition. Finally, the use of standard symbols for chemical species rather than species identification numbers is included to facilitate use of the program. One of the main limitations of GEOSURF is that aqueous and surface speciation can only be calculated at fixed pH and at fixed concentration of total adsorbate. Thus, the program cannot perform reaction-path calculations: it cannot determine whether or not a solution is over- or under-saturated with respect to one or more solid phases. To check the proper running of GEOSURF, we have compared results generated by GEOSURF with those from two other programs, HYDRAQL and EQ3. The Davies equation and the "bdot" equation, respectively, are used in the latter two programs for calculating aqueous activity coefficients. An example of the model fit to experimental data for rutile in 0.001 M-2.0 M NaNO 3 is included.

Role of Sulfhydryl Sites on Bacterial Cell Walls in the Biosorption, Mobility and Bioavailability of Mercury and Uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myneni, Satish C.; Mishra, Bhoopesh; Fein, Jeremy

2009-04-01

The goal of this exploratory study is to provide a quantitative and mechanistic understanding of the impact of bacterial sulfhydryl groups on the bacterial uptake, speciation, methylation and bioavailability of Hg and redox changes of uranium. The relative concentration and reactivity of different functional groups present on bacterial surfaces will be determined, enabling quantitative predictions of the role of biosorption of Hg under the physicochemical conditions found at contaminated DOE sites.The hypotheses we propose to test in this investigation are as follows- 1) Sulfhydryl groups on bacterial cell surfaces modify Hg speciation and solubility, and play an important role, specificallymore » in the sub-micromolar concentration ranges of metals in the natural and contaminated systems. 2) Sulfhydryl binding of Hg on bacterial surfaces significantly influences Hg transport into the cell and the methylation rates by the bacteria. 3) Sulfhydryls on cell membranes can interact with hexavalent uranium and convert to insoluble tetravalent species. 4) Bacterial sulfhydryl surface groups are inducible by the presence of metals during cell growth. Our studies focused on the first hypothesis, and we examined the nature of sulfhydryl sites on three representative bacterial species: Bacillus subtilis, a common gram-positive aerobic soil species; Shewanella oneidensis, a facultative gram-negative surface water species; and Geobacter sulfurreducens, an anaerobic iron-reducing gram-negative species that is capable of Hg methylation; and at a range of Hg concentration (and Hg:bacterial concentration ratio) in which these sites become important. A summary of our findings is as follows- Hg adsorbs more extensively to bacteria than other metals. Hg adsorption also varies strongly with pH and chloride concentration, with maximum adsorption occurring under circumneutral pH conditions for both Cl-bearing and Cl-free systems. Under these conditions, all bacterial species tested exhibit almost complete removal of Hg from the experimental solutions at relatively low bacterial concentrations. Synchrotron based X-ray spectroscopic studies of these samples indicate that the structure and the coordination environment of Hg surface complexes on bacterial cell walls change dramatically- with sulfhydryls as the dominant Hg-binding groups in the micromolar and submicromolar range, and carboxyls and phosphoryls dominating at high micromolar concentrations. Hg interactions change from a trigonal or T-shaped HgS{sub 3} complex to HgS or HgS{sub 2} type complexes as the Hg concentration increases in the submicromolar range. Although all bacterial species studied exhibited the same types of coordination environments for Hg, the relative concentrations of the complexes change as a function of Hg concentration.« less

Phylogenetic ecology of leaf surface traits in the milkweeds (Asclepias spp.): chemistry, ecophysiology, and insect behavior.

PubMed

Agrawal, Anurag A; Fishbein, Mark; Jetter, Reinhard; Salminen, Juha-Pekka; Goldstein, Jessica B; Freitag, Amy E; Sparks, Jed P

2009-08-01

The leaf surface is the contact point between plants and the environment and plays a crucial role in mediating biotic and abiotic interactions. Here, we took a phylogenetic approach to investigate the function, trade-offs, and evolution of leaf surface traits in the milkweeds (Asclepias). Across 47 species, we found trichome densities of up to 3000 trichomes cm(-2) and epicuticular wax crystals (glaucousness) on 10 species. Glaucous species had a characteristic wax composition dominated by very-long-chain aldehydes. The ancestor of the milkweeds was probably a glaucous species, from which there have been several independent origins of glabrous and pubescent types. Trichomes and wax crystals showed negatively correlated evolution, with both surface types showing an affinity for arid habitats. Pubescent and glaucous milkweeds had a higher maximum photosynthetic rate and lower stomatal density than glabrous species. Pubescent and glaucous leaf surfaces impeded settling behavior of monarch caterpillars and aphids compared with glabrous species, although surface types did not show consistent differentiation in secondary chemistry. We hypothesize that pubescence and glaucousness have evolved as alternative mechanisms with similar functions. The glaucous type, however, appears to be ancestral, lost repeatedly, and never regained; we propose that trichomes are a more evolutionarily titratable strategy.

Fingerprints of endogenous process on Europa through linear spectral modeling of ground-based observations (ESO/VLT/SINFONI)

NASA Astrophysics Data System (ADS)

Ligier, Nicolas; Carter, John; Poulet, François; Langevin, Yves; Dumas, Christophe; Gourgeot, Florian

2016-04-01

Jupiter's moon Europa harbors a very young surface dated, based on cratering rates, to 10-50 M.y (Zahnle et al. 1998, Pappalardo et al. 1999). This young age implies rapid surface recycling and reprocessing, partially engendered by a global salty subsurface liquid ocean that could result in tectonic activity (Schmidt et al. 2011, Kattenhorn et al. 2014) and active plumes (Roth et al. 2014). The surface of Europa should contain important clues about the composition of this sub-surface briny ocean and about the potential presence of material of exobiological interest in it, thus reinforcing Europa as a major target of interest for upcoming space missions such as the ESA L-class mission JUICE. To perform the investigation of the composition of the surface of Europa, a global mapping campaign of the satellite was performed between October 2011 and January 2012 with the integral field spectrograph SINFONI on the Very Large Telescope (VLT) in Chile. The high spectral binning of this instrument (0.5 nm) is suitable to detect any narrow mineral signature in the wavelength range 1.45-2.45 μm. The spatially resolved spectra we obtained over five epochs nearly cover the entire surface of Europa with a pixel scale of 12.5 by 25 m.a.s (~35 by 70 km on Europa's surface), thus permitting a global scale study. Until recently, a large majority of studies only proposed sulfate salts along with sulfuric acid hydrate and water-ice to be present on Europa's surface. However, recent works based on Europa's surface coloration in the visible wavelength range and NIR spectral analysis support the hypothesis of the predominance of chlorine salts instead of sulfate salts (Hand & Carlson 2015, Fischer et al. 2015). Our linear spectral modeling supports this new hypothesis insofar as the use of Mg-bearing chlorines improved the fits whatever the region. As expected, the distribution of sulfuric acid hydrate is correlated to the Iogenic sulfur ion implantation flux distribution (Hendrix et al. 2011, Dalton et al. 2013). However, the distribution of chlorine species is inconsistent with this process and together with abundance maps of different sizes of crystalline water-ice grain exhibits clear spatial inhomogeneities in their distribution, hence suggesting an endogenous origin for these species. Abundance maps will be presented and the question of the distribution and the formation of these species will be addressed.

Light and electron microscopic observations on the organization of skin and associated glands of two caecilian amphibians from Western Ghats of India.

PubMed

Damodaran, Arun; Reston Saroja, Beyo; Kotharambath, Ramachandran; Mohammad Abdulkader, Akbarsha; Oommen, Oommen V; Lekha, Divya

2018-03-01

We adopted light and electron microscopy to understand the structure of the skin of two species of caecilians, Ichthyophis tricolor and Uraeotyphlus cf. oxyurus, from Western Ghats of Kerala, India. The surface of the skin of these caecilians contains an irregular pattern of microridges. Oval, round and polymorphic glandular openings are randomly distributed all over the skin surface. Most of the openings are funnel shaped. The epithelial cells along the rim of the opening descend into the tunnel of the duct. A few glandular openings protrude slightly above the epithelium of the duct. The skin is formed of epidermis and dermis. Small flat disk-like dermal scales, composed of a basal plate of several layers of unmineralized collagen fibers topped with a discontinuous layer of mineralized globular squamulae, are lodged in pouches in the transverse ridges of the skin. Each pouch contains 1-4 scales, which might differ in size. The scales are almost similar between species, yet the difference can be useful in distinguishing between the two species. Flask cells and Merkel cells are present in the epidermis. Two types of glands, mucous and granular, are present in the dermis. The mucous glands are densely packed with mucous vesicles. Darkly stained mucous producing cells are located around the periphery of the gland. Secretory mucous vesicles differ in their organization and distribution. The granular glands are located perpendicular to the skin surface. The granule producing cells of the gland are located near the periphery. There are differently stained spherical secretory granules of various sizes in the cytoplasm. Thus, the use of different microscopic techniques contributed fascinatingly to the first ever understanding of organization of the skin of two selected caecilian species from Western Ghats, revealing certain features to differ between them. Copyright © 2018 Elsevier Ltd. All rights reserved.

Method for chemical surface modification of fumed silica particles

DOEpatents

Grabbe, Alexis; Michalske, Terry Arthur; Smith, William Larry

1999-01-01

Dehydroxylated, silica-containing, glass surfaces are known to be at least partially terminated by strained siloxane rings. According to the invention, a surface of this kind is exposed to a selected silane compound or mixture of silane compounds under reaction-promoting conditions. The ensuing reaction results in opening of the strained siloxane rings, and termination of surface atoms by chemical species, such as organic or organosilicon species, having desirable properties. These species can be chosen to provide qualities such as hydrophobicity, or improved coupling to a polymeric coating.

The Post-Glacial Species Velocity of Picea glauca following the Last Glacial Maximum in Alaska.

NASA Astrophysics Data System (ADS)

Morrison, B. D.; Napier, J.; Kelly, R.; Li, B.; Heath, K.; Hug, B.; Hu, F.; Greenberg, J. A.

2015-12-01

Anthropogenic climate change is leading to dramatic fluctuations to Earth's biodiversity that has not been observed since past interglacial periods. There is rising concern that Earth's warming climate will have significant impacts to current species ranges and the ability of a species to persist in a rapidly changing environment. The paleorecord provides information on past species distributions in relation to climate change, which can illuminate the patterns of potential future distributions of species. Particularly in areas where there are multiple potential limiting factors on a species' range, e.g. temperature, radiation, and evaporative demand, the spatial patterns of species migrations may be particularly complex. In this study, we assessed the change in the distributions of white spruce (Picea glauca) from the Last Glacial Maxima (LGM) to present-day for the entire state of Alaska. To accomplish this, we created species distribution models (SDMs) calibrated from modern vegetation data and high-resolution, downscaled climate surfaces at 60m. These SDMs were applied to downscaled modern and paleoclimate surfaces to produce estimated ranges of white spruce during the LGM and today. From this, we assessed the "species velocity", the rate at which white spruce would need to migrate to keep pace with climate change, with the goal of determining whether the expansion from the LGM to today originated from microclimate refugia. Higher species velocities indicate locations where climate changed drastically and white spruce would have needed to migrate rapidly to persist and avoid local extinction. Conversely, lower species velocities indicated locations where the local climate was changing less rapidly or was within the center of the range of white spruce, and indicated locations where white spruce distributions were unlikely to have changed significantly. Our results indicate the importance of topographic complexity in buffering the effects of climate change, particularly near the edges of the species' range.

Toxicity of chromated copper arsenate (CCA)-treated wood to non-target marine fouling communities in Langstone Harbour, Portsmouth, UK.

PubMed

Brown, C J; Eaton, R A

2001-04-01

The effect of the anti-marine-borer timber preservative chromated copper arsenate (CCA) (a pressure impregnated solution of copper, chromium and arsenic compounds) on non-target marine fouling animals was investigated during a subtidal exposure trial. Panels of Scots pine treated to target retentions of 12, 24 and 48 kg CCA per m-3 of wood, plus untreated controls were submerged at a coastal site on the south coast of the UK for 6, 12 and 18 months. After each exposure period the fouling communities that formed on the surface of panels were assessed both qualitatively and quantitatively. Community structure was similar on panels treated to the three CCA loadings, but was significantly different from community structure on untreated panels. The total number of species (species richness) was similar on all panels, although the number of individual organisms attached to the surface of panels was significantly higher on CCA-treated panels than on untreated panels. k-dominance curves revealed that the difference in numbers of individuals between CCA-treated and untreated panels was caused by higher numbers of the dominant species (Elminius modestus, Hydroides ezoensis, and Electra pilosa) on CCA-treated panels. Other species were present in similar numbers on panels of all treatments. Results indicate that there are no detrimental toxic effects to epibiota caused by the presence of CCA preservative within the matrix of the wood at any of the treatment levels. Differences in community structure between CCA-treated and untreated panels may be due to enhanced larval settlement on CCA-treated timber by some species as a result of modifications to the surface properties of the timber by the CCA preservative.

Herschel Observations of Extraordinary Sources: Analysi sof the HIFI 1.2 THz Wide Spectral Survey toward Orion KL II. Chemical Implications

NASA Astrophysics Data System (ADS)

Crockett, N. R.; Bergin, E. A.; Neill, J. L.; Favre, C.; Blake, G. A.; Herbst, E.; Anderson, D. E.; Hassel, G. E.

2015-06-01

We present chemical implications arising from spectral models fit to the Herschel/HIFI spectral survey toward the Orion Kleinmann-Low nebula (Orion KL). We focus our discussion on the eight complex organics detected within the HIFI survey utilizing a novel technique to identify those molecules emitting in the hottest gas. In particular, we find the complex nitrogen bearing species CH3CN, C2H3CN, C2H5CN, and NH2CHO systematically trace hotter gas than the oxygen bearing organics CH3OH, C2H5OH, CH3OCH3, and CH3OCHO, which do not contain nitrogen. If these complex species form predominantly on grain surfaces, this may indicate N-bearing organics are more difficult to remove from grain surfaces than O-bearing species. Another possibility is that hot (Tkin ∼ 300 K) gas phase chemistry naturally produces higher complex cyanide abundances while suppressing the formation of O-bearing complex organics. We compare our derived rotation temperatures and molecular abundances to chemical models, which include gas-phase and grain surface pathways. Abundances for a majority of the detected complex organics can be reproduced over timescales ≳105 years, with several species being underpredicted by less than 3σ. Derived rotation temperatures for most organics, furthermore, agree reasonably well with the predicted temperatures at peak abundance. We also find that sulfur bearing molecules that also contain oxygen (i.e., SO, SO2, and OCS) tend to probe the hottest gas toward Orion KL, indicating the formation pathways for these species are most efficient at high temperatures. Herschel is an ESA space observatory with science instruments provided by European-led Principal Investigator consortia and with important participation from NASA.

Quartz Crystal Microbalance Operation and In Situ Calibration

NASA Technical Reports Server (NTRS)

Albyn, K. C.

2004-01-01

Quartz crystal microbalances (QCMs) are commonly used to measure the rate of deposition of molecular species on a surface. The measurement is often used to select materials with a low outgassing rate for applications where the material has a line of sight to a contamination-sensitive surface. A quantitative, in situ calibration of the balance, or balances, using a pure material for which the enthalpy of sublimation is known, is described in this Technical Memorandum. Supporting calculations for surface dwell times of deposited materials and the effusion cell Clausing factor are presented along with examples of multiple QCM measurements of outgassing from a common source.

Detection of surface impurity phases in high T.sub.C superconductors using thermally stimulated luminescence

DOEpatents

Cooke, D. Wayne; Jahan, Muhammad S.

1989-01-01

Detection of surface impurity phases in high-temperature superconducting materials. Thermally stimulated luminescence has been found to occur in insulating impurity phases which commonly exist in high-temperature superconducting materials. The present invention is sensitive to impurity phases occurring at a level of less than 1% with a probe depth of about 1 .mu.m which is the region of interest for many superconductivity applications. Spectroscopic and spatial resolution of the emitted light from a sample permits identification and location of the impurity species. Absence of luminescence, and thus of insulating phases, can be correlated with low values of rf surface resistance.

Surface charge dynamics and OH and H number density distributions in near-surface nanosecond pulse discharges at a liquid / vapor interface

NASA Astrophysics Data System (ADS)

Winters, Caroline; Petrishchev, Vitaly; Yin, Zhiyao; Lempert, Walter R.; Adamovich, Igor V.

2015-10-01

The present work provides insight into surface charge dynamics and kinetics of radical species reactions in nanosecond pulse discharges sustained at a liquid-vapor interface, above a distilled water surface. The near-surface plasma is sustained using two different discharge configurations, a surface ionization wave discharge between two exposed metal electrodes and a double dielectric barrier discharge. At low discharge pulse repetition rates (~100 Hz), residual surface charge deposition after the discharge pulse is a minor effect. At high pulse repetition rates (~10 kHz), significant negative surface charge accumulation over multiple discharge pulses is detected, both during alternating polarity and negative polarity pulse trains. Laser induced fluorescence (LIF) and two-photon absorption LIF (TALIF) line imaging are used for in situ measurements of spatial distributions of absolute OH and H atom number densities in near-surface, repetitive nanosecond pulse discharge plasmas. Both in a surface ionization wave discharge and in a double dielectric barrier discharge, peak measured H atom number density, [H] is much higher compared to peak OH number density, due to more rapid OH decay in the afterglow between the discharge pulses. Higher OH number density was measured near the regions with higher plasma emission intensity. Both OH and especially H atoms diffuse out of the surface ionization wave plasma volume, up to several mm from the liquid surface. Kinetic modeling calculations using a quasi-zero-dimensional H2O vapor / Ar plasma model are in qualitative agreement with the experimental data. The results demonstrate the experimental capability of in situ radical species number density distribution measurements in liquid-vapor interface plasmas, in a simple canonical geometry that lends itself to the validation of kinetic models.

Differentially-expressed opsin genes identified in Sinocyclocheilus cavefish endemic to China

PubMed Central

Meng, Fanwei; Zhao, Yahui; Postlethwait, John H.; Zhang, Chunguang

2013-01-01

Eye degeneration is a common troglomorphic character of cave-dwelling organisms. Comparing the morphology and molecular biology of cave species and their close surface relatives is a powerful tool for studying regressive eye evolution and other adaptive phenotypes. We compared two co-occurring and closely-related species of the fish genus Sinocyclocheilus, which is endemic to China and includes both surface- and cave-dwelling species. Sinocyclocheilus tileihornes, a cave species, had smaller eyes than Sinocyclocheilus angustiporus, a surface species. Histological and immunohistochemical analyses revealed that the cavefish had shorter cones and more disorderly rods than did the surface-dwelling species. Using quantitative PCR and in situ hybridization, we found that rhodopsin and a long-wavelength sensitive opsin had significantly lower expression levels in the cavefish. Furthermore, one of two short-wavelength-sensitive opsins was expressed at significantly higher levels in the cavefish. Changes in the expression of opsin genes may have played a role in the degeneration of cavefish eyes PMID:24363664

Ligand-modified metal clusters for gas separation and purification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okrut, Alexander; Ouyang, Xiaoying; Runnebaum, Ron

2017-02-21

Provided is an organic ligand-bound metal surface that selects one gaseous species over another. The species can be closely sized molecular species having less than 1 Angstrom difference in kinetic diameter. In one embodiment, the species comprise carbon monoxide and ethylene. Such organic ligand-bound metal surfaces can be successfully used in gas phase separations or purifications, sensing, and in catalysis.

Viewing Mercury's Surface-bound Exosphere from Orbit: Eighteen Months of Observations by the Mercury Atmospheric and Surface Composition Spectrometer aboard the MESSENGER Spacecraft

NASA Astrophysics Data System (ADS)

McClintock, W. E.; Benna, M.; Burger, M. H.; Cassidy, T.; Killen, R. M.; Merkel, A. W.; Sarantos, M.; Solomon, S. C.; Sprague, A. L.; Vervack, R. J.

2012-12-01

Prior to the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) mission, Mercury's surface-bounded exosphere was known to contain H and He, observed by Mariner 10, as well as Na, K, and Ca, observed from the ground. The exosphere is the interface between the planet's surface and the surrounding space environment. Its composition and structure are controlled by interactions among the surface, magnetosphere, solar wind, sunlight, and impacting meteoroids. When species are liberated from the surface with sufficient energy, they can be accelerated by solar radiation pressure to form an anti-sunward tail. During three flybys en route to orbit, the Ultraviolet and Visible Spectrometer (UVVS) channel of the Mercury Atmospheric and Surface Composition Spectrometer (MASCS) aboard MESSENGER discovered Mg in the tail and detected Ca+ in a narrow region centered ~ 2.5 Mercury radii anti-sunward of the planet's terminator. UVVS began routine orbital observations of both the dayside and nightside exosphere on March 29, 2011. It regularly measures altitude profiles for all previously detected neutral species with the exception of He and K. The former has no emission features within the UVVS wavelength range (115-600 nm), and the latter has only one relatively weak feature there. A single component of Ca is usually observed at lower altitudes (~2000 km) and exhibits the strong equatorial, dawn enhancement observed during the flybys. Mg distributions exhibit two components. The more energetic component has been detected at high altitudes, up to 4000 km above the surface on both the dayside and nightside, and shows a dawn enhancement similar to Ca. Dayside distributions of Na exhibit two components with e-folding heights comparable to profiles above the poles obtained during the third flyby. Concentrations of all three species exhibit seasonal variability. The best studied of these is Na, for which maximum dayside density occurs at a Mercury true anomaly angle of 180°. UVVS also observes H. It is less well studied than Ca, Mg, and Na because signal from the exospheric H is often contaminated by emission from interplanetary hydrogen and sunlight reflected from the surface. O has also been detected near the subsolar point, but its emission is too weak for routine study. UVVS observations also include wavelength scans for neutral species that are known or are predicted to be present in the surface materials (e.g., Si, Al, S, Mn, Fe, and OH), but emissions from these species are not sufficiently bright for detection with current operational scenarios. The UVVS team uses a variety of techniques to relate exosphere composition and structure to source processes, including tomographic inversion and Monte Carlo modeling. Correlations of Mercury's neutral exosphere composition and structure with direct measurements of the space environment from MESSENGER's Magnetometer (MAG) and Energetic Particle and Plasma Spectrometer (EPPS) provide further insight into source processes.

Proteomic analysis of a model fish species exposed to individual pesticides and a binary mixture--Presentation

EPA Science Inventory

Pesticides are nearly ubiquitous in surface waters of the United States, where they often are found as mixtures. The molecular mechanisms underlying the toxic effects of sub-lethal exposure to pesticides as both individual and mixtures are unclear. The current work aims to ident...

Community ecology of fungal pathogens on Bromus tectorum [Chapter 7

Treesearch

Susan E. Meyer; Julie Beckstead; JanaLynn Pearce

2016-01-01

Bromus tectorum L. (cheatgrass or downy brome) presents a rich resource for soil microorganisms because of its abundant production of biomass, seeds, and surface litter. Many of these organisms are opportunistic saprophytes, but several fungal species regularly found in B. tectorum stands function as facultative or obligate pathogens. These organisms interact...

Chemical desorption and diffusive dust chemistry

NASA Astrophysics Data System (ADS)

Dulieu, Francois; Pirronello, Valerio; Minissale, Marco; Congiu, Emanuele; Baouche, Saoud; Chaabouni, Henda; Moudens, Audrey; Accolla, Mario; Cazaux, Stephanie; Manicò, Giulio

In molecular clouds, gaseous species can accrete efficiently on the cold surfaces of dust grains. As for radical-radical reactions, the surface of the grains acts as a third body, and changes dramatically the efficiency of the reactions (i.e., H2 formation), or lowers considerably the barrier to formation (i.e., H2O synthesis) in comparison with gas phase reaction processes. These properties make dust grains efficient catalytic templates. However, the chemical role of dust grains depends on the diffusive properties of the reactive partners. Over the last years, we have developed experimental tools and methods to explore the chemistry occurring on cold (6-50K) surfaces. We have obtained some hints about the diffusivity of H on amorphous ice, and studied in detail the diffusion of O atoms. The latter species appears to have a hopping rate in the range 0.01-100 hops/sec. The diffusion rate of O atoms is dependent on the surface morphology and on the surface temperature. The diffusion law is compatible with a diffusion dominated by quantum tunnelling rather than classical thermal hopping. Using H, O, N atoms and, indirectly, OH and HCO radicals, we have begun to explore many chemical reactive networks. In this presentation, I will focus on the formation of H2O and CO2, and will propose many possible formation routes to obtain these chemical traps. The molecules formed on surfaces have a certain probability of desorbing upon their formation. This non-thermal desorption mechanism, or chemical desorption, has been proposed to explain why some molecules can be detected in the gas phase of those region where they were believed to be part of the icy mantles covering dust grains. We have shown that this process can be very efficient, but is very sensitive to the substrate and the surroundings of the reaction site, is dependent on the kind of molecule formed and its chemical pathway. In my presentation I will present how the surface coverage and the type of reaction can play a major role in the chemical desorption process. I will discuss of possible key parameters that rule this process.

A Dusty Coma Model of Comet Hyakutake

NASA Astrophysics Data System (ADS)

Boice, D. C.; Benkhoff, J.

1996-09-01

We present a multifluid, hydrodynamic model for the gas, dust, and plasma flow in a cometary coma appropriate for Comet Hyakutake. The model accounts for three sources of gas release: sublimation from surface ices, transport of gas from subsurface regions through the surface, and release of gas from dust in the coma. The simulations are based on a spherically symmetric neutral coma model with detailed photo and gas-phase chemistry and dust entrainment by the gas. The model includes a separate energy balance for the electrons, separate flow of the neutral gas, fast neutral atomic and molecular hydrogen, and dust entrainment with fragmentation. The simulations allow a study of how certain features of a cometary coma, e.g., spatial distributions of gas-phase species and dust of various sizes, change with heliocentric distance. Special attention is given to observations of hydrocarbon and sulphur species. In comparison with observations, the model can be used to characterize the environment surrounding Hyakutake and aid in assimilating a variety of diverse observations of this bright comet. A complete description of the model and more extensive results with comparisons to observations where possible will be presented.

Microsporidian species known to infect humans are present in aquatic birds: implications for transmission via water?

PubMed

Slodkowicz-Kowalska, Anna; Graczyk, Thaddeus K; Tamang, Leena; Jedrzejewski, Szymon; Nowosad, Andrzej; Zduniak, Piotr; Solarczyk, Piotr; Girouard, Autumn S; Majewska, Anna C

2006-07-01

Human microsporidiosis, a serious disease of immunocompetent and immunosuppressed people, can be due to zoonotic and environmental transmission of microsporidian spores. A survey utilizing conventional and molecular techniques for examining feces from 570 free-ranging, captive, and livestock birds demonstrated that 21 animals shed microsporidian spores of species known to infect humans, including Encephalitozoon hellem (20 birds; 3.5%) and Encephalitozoon intestinalis (1 bird; 0.2%). Of 11 avian species that shed E. hellem and E. intestinalis, 8 were aquatic birds (i.e., common waterfowl). The prevalence of microsporidian infections in waterfowl (8.6%) was significantly higher than the prevalence of microsporidian infections in other birds (1.1%) (P < 0.03); waterfowl fecal droppings contained significantly more spores (mean, 3.6 x 10(5) spores/g) than nonaquatic bird droppings contained (mean, 4.4 x 10(4) spores/g) (P < 0.003); and the presence of microsporidian spores of species known to infect humans in fecal samples was statistically associated with the aquatic status of the avian host (P < 0.001). We demonstrated that a single visit of a waterfowl flock can introduce into the surface water approximately 9.1 x 10(8) microsporidian spores of species known to infect humans. Our findings demonstrate that waterborne microsporidian spores of species that infect people can originate from common waterfowl, which usually occur in large numbers and have unlimited access to surface waters, including waters used for production of drinking water.

Marine genomics: News and views.

PubMed

Ribeiro, Ângela M; Foote, Andrew D; Kupczok, Anne; Frazão, Bárbara; Limborg, Morten T; Piñeiro, Rosalía; Abalde, Samuel; Rocha, Sara; da Fonseca, Rute R

2017-02-01

Marine ecosystems occupy 71% of the surface of our planet, yet we know little about their diversity. Although the inventory of species is continually increasing, as registered by the Census of Marine Life program, only about 10% of the estimated two million marine species are known. This lag between observed and estimated diversity is in part due to the elusiveness of most aquatic species and the technical difficulties of exploring extreme environments, as for instance the abyssal plains and polar waters. In the last decade, the rapid development of affordable and flexible high-throughput sequencing approaches have been helping to improve our knowledge of marine biodiversity, from the rich microbial biota that forms the base of the tree of life to a wealth of plant and animal species. In this review, we present an overview of the applications of genomics to the study of marine life, from evolutionary biology of non-model organisms to species of commercial relevance for fishing, aquaculture and biomedicine. Instead of providing an exhaustive list of available genomic data, we rather set to present contextualized examples that best represent the current status of the field of marine genomics. Copyright © 2016 Elsevier B.V. All rights reserved.

Physical Constraints on the Ices present on Triton's Surface

NASA Astrophysics Data System (ADS)

Merlin, Frederic; Lellouch, Emmanuel; Quirico, Eric; Schmitt, Bernard

2017-10-01

Triton is the largest distant satellite of the solar system and was probably captured from the Transneptunian population by Neptune. It is mainly covered by N2 , CO, CO2 , CH4 and H2O in solid state and, except for H2O and CO2 , these species are also present in gas phase (with a thin N2 rich atmosphere, with CH4 and CO traces, see Lellouch et al., 2011, for instance). Sublimation and recondensation of the volatile species could lead to geographical and temporal variation, and could participate to the formation of complex chemical compounds formed from photochemistry occurring in the atmosphere (Krasnopolsky and Cruikshank, 1999) or from irradiation of N2 :CH4 :CO layers (Moore and Hudson, 2003).We present new analyses based on observations that have been performed in the near Infrared at the VLT-ESO with SINFONI from 2010 to 2013 at a spectral resolution ranging from 1500 to 4000, in order to give new constraints on the chemical and physical properties of the surface. Several models based on the Hapke theory (Hapke, 1993) have also been tested in order to constrain the abundance, the grain size and the state of the major ices (N2 , CH4 , CO, CO2 , H2O) as well as an attempt to identify other species. For this purpose, we use new optical constants of CO2 performed at 35 and 54K.We confirm the presence of deep N2 layers in which CO and CH4 are diluted. Our models highly support the presence of pure CH4 ice that can explain the enhancement of the CH4/N2 gas ratio in the atmosphere over what would be expected from ideal mixing. Our results also suggest significant smaller particles of CO2 and H2O than that reported in Quirico et al. (1999). H2O is expected to be present in its crystalline phase and CO2 spectral bands are compatible with a highly crystalline structure. Our models also suggest that CO2 is probably spread over a large area of the Triton surface. Our analyses do not support the presence of higher order hydrocarbons, such as those reported by Merlin (2015) on the surface of Pluto.

Potential impacts of projected climate change on vegetation-management strategies in Hawai‘i Volcanoes National Park

USGS Publications Warehouse

Camp, Richard J.; Berkowitz, S. Paul; Brink, Kevin W.; Jacobi, James D.; Loh, Rhonda; Price, Jonathan; Fortini, Lucas B.

2018-06-05

Climate change is expected to alter the seasonal and annual patterns of rainfall and temperature in the Hawaiian Islands. Land managers and other responsible agencies will need to know how plant-species habitats will change over the next century in order to manage these resources effectively. This issue is a major concern for resource managers at Hawai‘i Volcanoes National Park (HAVO), where currently managed Special Ecological Areas (SEAs) for important plant species and communities may no longer provide suitable habitats in the future as the climate changes. Expanding invasive-species distributions also may pose a threat to areas where native plants currently predominate.The objective of this project was to combine recent climate-modeling efforts for the state of Hawai‘i with existing models of plant-species distribution in order to forecast suitable habitat ranges under future climate conditions derived from the Coupled Model Intercomparison Project, phase 3 (CMIP3) global circulation model that was dynamically downscaled for the Hawaiian Islands by using the Hawai‘i Regional Climate Model (HRCM). The HRCM uses the A1B emission scenario (a median future climate projection) from the Special Report on Emissions Scenarios (SRES). On the basis of this model, maps showing projected plant-species ranges were generated for four years as snapshots in time (2000, 2040, 2070, 2090) and for three different trajectories of climate change (gradual, linear, rapid) between the present and future.We mapped probabilistic surfaces of suitable habitat for 39 plant species (both native and alien [nonnative]) identified as being of interest to HAVO resource managers. We displayed these surfaces in terms of change relative to present conditions, whether the range of a given plant species was expected to contract, expand, or remain the same in the future. Within HAVO, approximately two-thirds (18 of 29) of the modeled native plant species were projected to contract in range, whereas one-third (11 of 29) were projected to increase. Most of the HAVO SEAs were projected to lose most of the native plant species modeled. Within HAVO, all alien plant species except Lantana camara were projected to contract in range within the park; this trend was observed in most SEAs, including those at low, middle, and high elevations. Congruence was good in the “current” (2000) distribution of plant-species richness and SEA configurations; however, the congruence between species-richness hotspots and SEAs diminished by the projected “end-of-century” (2090) distribution. Over time, the projected species-richness hotspots increasingly occurred outside of the currently configured SEA boundaries.

A travel in the Echeveria genus wettability's world

NASA Astrophysics Data System (ADS)

Godeau, Guilhem; Laugier, Jean-Pierre; Orange, François; Godeau, René-Paul; Guittard, Frédéric; Darmanin, Thierry

2017-07-01

Nature is a constant source of inspiration for researchers and engineers. In this work, we study the wettability of various species from the genus Echeveria. All species studied present very strong hydrophobic properties with various water adhesions. Echeveria 'Perle von Nürnberg' has properties very close to superhydrophobicity with low water adhesion (sliding angle α = 15° and contact angle hysteresis H = 9°) while Echeveria pallida and Echeveria runyonii are completely sticky (parahydrophobic) and water droplets do not move even if the surface is inclined to 90°. This work shows that most of the differences in the hydrophobic properties depend on the amount of wax crystallization. However, Echeveria pulvinata shows special wettability results. Their leaves possess long hairs. When a water droplet is placed on the surface, the water droplet is completely sticky. When the size of the droplets becomes critical, the water droplets spread across the leaf surface displaying superhydrophilic properties. More investigations reveal that the hairs are highly hydrophobic and rough due to the presence of wax crystals while the bottom of the surface is smooth and hydrophilic. Such materials are excellent candidates for water harvesting systems and oil/water separation membranes.

Apparatus for in situ cleaning of carbon contaminated surfaces

DOEpatents

Klebanoff, Leonard E.; Grunow, Philip; Graham, Jr., Samuel

2004-08-10

Activated gaseous species generated adjacent a carbon contaminated surface affords in-situ cleaning. A device for removing carbon contamination from a surface of the substrate includes (a) a housing defining a vacuum chamber in which the substrate is located; (b) a source of gaseous species; and (c) a source of electrons that are emitted to activate the gaseous species into activated gaseous species. The source of electrons preferably includes (i) a filament made of a material that generates thermionic electron emissions; (ii) a source of energy that is connected to the filament; and (iii) an electrode to which the emitted electrons are attracted. The device is particularly suited for photolithography systems with optic surfaces, e.g., mirrors, that are otherwise inaccessible unless the system is dismantled.

Environmental Niche Overlap between Common and Dusky Dolphins in North Patagonia, Argentina

PubMed Central

Svendsen, Guillermo Martín; Romero, María Alejandra; Williams, Gabriela Noemí; Gagliardini, Domingo Antonio; Crespo, Enrique Alberto; Dans, Silvana Laura; González, Raúl Alberto

2015-01-01

Research on the ecology of sympatric dolphins has increased worldwide in recent decades. However, many dolphin associations such as that between common dolphins (Delphinus delphis) and dusky dolphins (Lagenorhynchus obscurus) are poorly understood. The present study was conducted in the San Matías Gulf (SMG) ecosystem (North Patagonia, Argentina) where a high diet overlap among both species was found. The main objective of the present work was to explore the niche overlap of common and dusky dolphins in the habitat and temporal dimensions. The specific aims were (a) to evaluate the habitat use strategies of both species through a comparison of their group attributes (social composition, size and activity), and (b) to evaluate their habitat preferences and habitat overlap through Environmental Niche modeling considering two oceanographic seasons. To accomplish these aims, we used a historic database of opportunistic and systematic records collected from 1983 to 2011. Common and dusky dolphins exhibited similar patterns of group size (from less than 10 to more than 100 individuals), activity (both species use the area to feed, nurse, and copulate), and composition (adults, juveniles, and mothers with calves were observed for both species). Also, both species were observed travelling and feeding in mixed-species groups. Specific overlap indices were higher for common dolphins than for dusky dolphins, but all indices were low, suggesting that they are mainly segregated in the habitat dimension. In the case of common dolphins, the best habitats were located in the northwest of the gulf far from the coast. In the warm season they prefer areas with temperate sea surface and in the cold season they prefer areas with relatively high variability of sea surface temperature. Meanwhile, dusky dolphins prefer areas with steep slopes close to the coast in the southwestern sector of the gulf in both seasons. PMID:26091542

From well-defined Pt(II) surface species to the controlled growth of silica supported Pt nanoparticles.

PubMed

Laurent, Pierre; Veyre, Laurent; Thieuleux, Chloé; Donet, Sébastien; Copéret, Christophe

2013-01-07

Silica-supported Pt nanoparticles were prepared from well-defined surface platinum(II) surface species, obtained by grafting of well-defined Pt(II) molecular precursors with specific ligands (Cl, Me, N(SiMe(3))(2), OSi(OtBu)(3)) onto silica partially dehydroxylated at 200 and 700 °C yielding well-defined platinum(II) surface species. This approach allowed for testing the effect of Pt density and ligands on nanoparticle size. Higher grafting densities are achieved on silica partially dehydroxylated at 200 °C due to its initially higher surface silanol density. Surface species have been synthesized from symmetrical and dissymmetrical complexes, namely (COD)Pt(Me)(2), (COD)Pt(OSi(OtBu)(3))(2), (COD)Pt(Me)(OSi(OtBu)(3)), (COD)Pt(Me)(N(SiMe(3))(2)), (COD)Pt(Cl)(N(SiMe(3))(2)) and (COD)Pt(N(SiMe(3))(2))(OSi(OtBu)(3)) yielding mono-grafted complexes of general formula (COD)Pt(R)(OSi≡) according to elemental analyses, diffuse reflectance infrared fourier transform (DRIFT) and carbon-13 solid-state nuclear magnetic resonance (NMR) spectroscopies. While the dimethyl-complex shows low reactivity towards grafting, bis-siloxy and dissymmetric complexes demonstrate better reactivity yielding platinum loadings up to 7.4 wt%. Upon grafting amido complexes, the surface passivation yielding Me(3)SiOSi≡ surface species is demonstrated. Nanoparticles have been synthesized from these well-defined surface species by reduction under H(2) at 300 °C, under static or flow conditions. This process yields nanoparticles with sizes ranging from 2 to 3.3 nm and narrow size dispersion from 0.5 to 1.2 nm. Interestingly, the chloride complex yields large nanoparticles from 5 to 40 nm demonstrating the strong influence of chloride over the nanoparticles growth.

Diffusion of anthracene derivatives on Cu(111) studied by STM and DFT

NASA Astrophysics Data System (ADS)

Wyrick, Jonathan; Bartels, Ludwig; Einstein, Theodore

2014-03-01

Substituted anthracenes have drawn attention due to their ability to diffuse uniaxially on a Cu(111) surface. We compare anthracene to three of its derivatives whose 9,10 hydrogens are replaced by elements of the chalcogen group that act as linkers binding the molecules to a Cu(111) substrate. DFT calculations shed light on STM imaging and diffusion studies on the three substituted species. We present an analysis of the DFT results in which energetic contributions to the diffusion barriers are partitioned among the Kohn-Sham orbitals, allowing us to make assignments as to how each orbital affects diffusion for each species and draw comparisons between them. Present address: Center for Nanoscale Science and Technology, NIST, Gaithersburg, MD.

Modification of porous silicon rugate filters through thiol-yne photochemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soeriyadi, Alexander H., E-mail: alexander.soeriyadi@unsw.edu.au; Zhu, Ying, E-mail: alexander.soeriyadi@unsw.edu.au; Gooding, J. Justin, E-mail: justin.gooding@unsw.edu.au

2014-02-24

Porous silicon (PSi) has a considerable potential as biosensor platform. In particular, the ability to modify the surface chemistry of porous silicon is of interest. Here we present a generic method to modify the surface of porous silicon through thiol-yne photochemistry initiated by a radical initiator. Firstly, a freshly etched porous silicon substrate is modified through thermal hydrosilylation with 1,8-nonadiyne to passivate the surface and introduce alkyne functionalities. The alkyne functional surface could then be further reacted with thiol species in the presence of a radical initiator and UV light. Functionalization of the PSi rugate filter is followed with opticalmore » reflectivity measurements as well as high resolution X-ray photoelectron spectroscopy (XPS)« less

Surface Passivation of CdZnTe Detector by Hydrogen Peroxide Solution Etching

NASA Technical Reports Server (NTRS)

Hayes, M.; Chen, H.; Chattopadhyay, K.; Burger, A.; James, R. B.

1998-01-01

The spectral resolution of room temperature nuclear radiation detectors such as CdZnTe is usually limited by the presence of conducting surface species that increase the surface leakage current. Studies have shown that the leakage current can be reduced by proper surface preparation. In this study, we try to optimize the performance of CdZnTe detector by etching the detector with hydrogen peroxide solution as function of concentration and etching time. The passivation effect that hydrogen peroxide introduces have been investigated by current-voltage (I-V) measurement on both parallel strips and metal-semiconductor-metal configurations. The improvements on the spectral response of Fe-55 and 241Am due to hydrogen peroxide treatment are presented and discussed.

Effect of plasma ion bombardment on the reflectance of Io's trailing and leading hemispheres

NASA Technical Reports Server (NTRS)

Sack, N. J.; Baragiola, R. A.; Johnson, R. E.

1993-01-01

The possible effect of a net difference in the ion bombardment flux to the surface of Io on the ratio of the reflectance spectra is investigated. Io's vapor-deposited surface layers are simulated by a laboratory-produced film of vapor-deposited SO2 with a small admixture (about 3 percent) of H2S and (about 0.1 percent) H2O. It is shown that the reflectance ratio in the UV/visible of the surface bombarded by keV ions to the unbombarded surface is surprisingly similar to the observed ratio of Io's trailing to leading hemispherical reflectance. The changes produced are either structural or involve products of species originally present in the sample.

Genetic differences in the serum proteome of horses, donkeys and mules are detectable by protein profiling.

PubMed

Henze, Andrea; Aumer, Franziska; Grabner, Arthur; Raila, Jens; Schweigert, Florian J

2011-10-01

Although horses and donkeys belong to the same genus, their genetic characteristics probably result in specific proteomes and post-translational modifications (PTM) of proteins. Since PTM can alter protein properties, specific PTM may contribute to species-specific characteristics. Therefore, the aim of the present study was to analyse differences in serum protein profiles of horses and donkeys as well as mules, which combine the genetic backgrounds of both species. Additionally, changes in PTM of the protein transthyretin (TTR) were analysed. Serum protein profiles of each species (five animals per species) were determined using strong anion exchanger ProteinChips® (Bio-Rad, Munich, Germany) in combination with surface-enhanced laser desorption ionisation-time of flight MS. The PTM of TTR were analysed subsequently by immunoprecipitation in combination with matrix-assisted laser desorption ionisation-time of flight MS. Protein profiling revealed species-specific differences in the proteome, with some protein peaks present in all three species as well as protein peaks that were unique for donkeys and mules, horses and mules or for horses alone. The molecular weight of TTR of horses and donkeys differed by 30 Da, and both species revealed several modified forms of TTR besides the native form. The mass spectra of mules represented a merging of TTR spectra of horses and donkeys. In summary, the present study indicated that there are substantial differences in the proteome of horses and donkeys. Additionally, the results probably indicate that the proteome of mules reveal a higher similarity to donkeys than to horses.

Evolution of the surface species of the V 2O 5-WO 3 catalysts

NASA Astrophysics Data System (ADS)

Najbar, M.; Brocławik, E.; Góra, A.; Camra, J.; Białas, A.; Wesełucha-Birczyńska, A.

2000-07-01

Vanadia-related species formed as a result of vanadium segregation at the surface of V-W oxide bronze crystallites were investigated. The structures of these species and their transformations induced by oxygen removal and oxygen adsorption were monitored using photoelectron spectroscopy and the FT Raman technique. Assignments of the MeO vibrational bands, based on the results of DFT calculations for model clusters, have been proposed. Two kinds of surface species are dominant depending on the tungsten content: V 4+-O-W 6+ at low tungsten content and V 5+-O-W 5+ at higher tungsten concentration.

Inland diatoms from the McMurdo Dry Valleys and James Ross Island, Antarctica

USGS Publications Warehouse

Esposito, R.M.M.; Spaulding, S.A.; McKnight, Diane M.; Van De Vijver, B.; Kopalova, K.; Lubinski, D.; Hall, B.; Whittaker, T.

2008-01-01

Diatom taxa present in the inland streams and lakes of the McMurdo Dry Valleys and James Ross Island, Antarctica, are presented in this paper. A total of nine taxa are illustrated, with descriptions of four new species (Luticola austroatlantica sp. nov., Luticola dolia sp. nov., Luticola laeta sp. nov., Muelleria supra sp. nov.). In the perennially ice-covered lakes of the McMurdo Dry Valleys, diatoms are confined to benthic mats within the photic zone. In streams, diatoms are attached to benthic surfaces and within the microbial mat matrix. One species, L. austroatlantica, is found on James Ross Island, of the southern Atlantic archipelago, and the McMurdo Dry Valleys. The McMurdo Dry Valley populations are at the lower range of the size spectrum for the species. Streams flow for 6-10 weeks during the austral summer, when temperatures and solar radiation allow glacial ice to melt. The diatom flora of the region is characterized by species assemblages favored under harsh conditions, with naviculoid taxa as the dominant group and several major diatom groups conspicuously absent. ?? 2008 NRC.

Ichthyobodo salmonis sp. n. (Ichthyobodonidae, Kinetoplastida), an euryhaline ectoparasite infecting Atlantic salmon (Salmo salar L.)

PubMed Central

ISAKSEN, TROND E.; KARLSBAKK, EGIL; WATANABE, KUNINORI; NYLUND, ARE

2011-01-01

SUMMARY Phylogenetic analyses of SSU rDNA sequences have previously revealed the existence of 2 Ichthyobodo species able to infect Atlantic salmon (Salmo salar L.). Ichthyobodo necator sensu stricto (s.s.) is assumed to be a freshwater parasite, while a genetically distinct but undescribed species, Ichthyobodo sp. II sensu Todal et al. (2004) have been detected on Atlantic salmon in both fresh- and seawater. In the present study a morphological description of Ichthyobodo sp. II from the gills of salmon reared in fresh-, brackish- and seawater is presented, using both light- and electron microscopy. Comparative morphometry show that Ichthyobodo sp. II from both freshwater and seawater displays a different cell shape, and is significantly smaller than I. necator s.s. Also, ultrastructural characteristics distinguish these two species, notably differences in the attachment region and the presence of spine-like surface projections in Ichthyobodo sp. II. Based on both unique SSU rDNA sequences and morphological characteristics, we conclude that Ichthyobodo sp. II. represents a novel species for which we propose the name Ichthyobodo salmonis sp. n. PMID:21756424

Landscape-scale evaluation of asymmetric interactions between Brown Trout and Brook Trout using two-species occupancy models

USGS Publications Warehouse

Wagner, Tyler; Jefferson T. Deweber,; Jason Detar,; John A. Sweka,

2013-01-01

Predicting the distribution of native stream fishes is fundamental to the management and conservation of many species. Modeling species distributions often consists of quantifying relationships between species occurrence and abundance data at known locations with environmental data at those locations. However, it is well documented that native stream fish distributions can be altered as a result of asymmetric interactions between dominant exotic and subordinate native species. For example, the naturalized exotic Brown Trout Salmo trutta has been identified as a threat to native Brook Trout Salvelinus fontinalis in the eastern United States. To evaluate large-scale patterns of co-occurrence and to quantify the potential effects of Brown Trout presence on Brook Trout occupancy, we used data from 624 stream sites to fit two-species occupancy models. These models assumed that asymmetric interactions occurred between the two species. In addition, we examined natural and anthropogenic landscape characteristics we hypothesized would be important predictors of occurrence of both species. Estimated occupancy for Brook Trout, from a co-occurrence model with no landscape covariates, at sites with Brown Trout present was substantially lower than sites where Brown Trout were absent. We also observed opposing patterns for Brook and Brown Trout occurrence in relation to percentage forest, impervious surface, and agriculture within the network catchment. Our results are consistent with other studies and suggest that alterations to the landscape, and specifically the transition from a forested catchment to one that contains impervious surface or agriculture, reduces the occurrence probability of wild Brook Trout. Our results, however, also suggest that the presence of Brown Trout results in lower occurrence probability of Brook Trout over a range of anthropogenic landscape characteristics, compared with streams where Brown Trout were absent.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dong; Xu, Pinghong; Guan, Erjia

Supported rhodium acetate dimers were prepared by the reaction of Rh2(OAc)4 (OAc is acetate) with highly dehydroxylated MgO powder and characterized by extended X-ray absorption fine structure and infrared (IR) spectra, which show that the supported species were well represented as Rh2(OAc)3, with each Rh atom on average bonded to one oxygen atom of the MgO surface. Aberration-corrected scanning transmission electron microscopy gave images of Rh atoms in pairs on the MgO. The supported rhodium dimers were probed with a pulse of CO, and the IR spectra indicate a Rh(II) species with weakly bonded carbonyl ligands; the sharpness of themore » νCO band indicates highly uniform surface species. Further treatment in CO led to breakup of the rhodium dimers into mononuclear species; such fragmentation took place in other treatment gases as well, with the degree of fragmentation decreasing in the order CO > C2H4 > helium. The fragmentation is inferred on the basis of IR spectra to have proceeded through intermediate Rh2 species without acetate ligands. In contrast, rhodium dimers were reduced and not fragmented in the presence of H2 at 353 K, but at higher temperatures the rhodium aggregated to give larger clusters. The supported species catalyzed ethylene hydrogenation at 298 K and 1 bar at a H2 to ethylene molar ratio of 4; after 27 h of catalysis in a once-through flow reactor, acetate ligands were removed from the dimers, and some of them fragmented, as shown by IR spectroscopy. The intermediate dirhodium species without acetate ligands are two or three orders of magnitude more active as catalysts than the supported mononuclear rhodium species or those present predominantly as Rh2(OAc)3, respectively.« less

Structure and function of complex I in animals and plants - a comparative view.

PubMed

Senkler, Jennifer; Senkler, Michael; Braun, Hans-Peter

2017-09-01

The mitochondrial NADH dehydrogenase complex (complex I) has a molecular mass of about 1000 kDa and includes 40-50 subunits in animals, fungi and plants. It is composed of a membrane arm and a peripheral arm and has a conserved L-like shape in all species investigated. However, in plants and possibly some protists it has a second peripheral domain which is attached to the membrane arm on its matrix exposed side at a central position. The extra domain includes proteins resembling prokaryotic gamma-type carbonic anhydrases. We here present a detailed comparison of complex I from mammals and flowering plants. Forty homologous subunits are present in complex I of both groups of species. In addition, five subunits are present in mammalian complex I, which are absent in plants, and eight to nine subunits are present in plant complex I which do not occur in mammals. Based on the atomic structure of mammalian complex I and biochemical insights into complex I architecture from plants we mapped the species-specific subunits. Interestingly, four of the five animal-specific and five of the eight to nine plant-specific subunits are localized at the inner surface of the membrane arm of complex I in close proximity. We propose that the inner surface of the membrane arm represents a workbench for attaching proteins to complex I, which are not directly related to respiratory electron transport, like nucleoside kinases, acyl-carrier proteins or carbonic anhydrases. We speculate that further enzyme activities might be bound to this micro-location in other groups of organisms. © 2017 Scandinavian Plant Physiology Society.

A new species of antipatharian coral (Cnidaria: Anthozoa: Antipatharia: Schizopathidae) from the Pacific coast of Costa Rica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Opresko, Dennis M; Breedy, Odalisca

A new species of black coral, Aphanipathes colombiana (Cnidaria:Antipatharia) from the Caribbean coast of Colombia is described. The species forms small flabellate colonies with anisomorphic polypar spines. It is morphologically similar to the western Atlantic species A. thyoides (Pourtales) but its hypostomal polypar spines are not reduced in size. The new species also resembles the Indo-Pacific species A. reticulata van Pesch but it has smooth-surfaced polypar spines, whereas in A. reticulata these spines have small tubercles on their surface

The influence of the carbonate species on LiNi0.8Co0.15Al0.05O2 surfaces for all-solid-state lithium ion battery performance

NASA Astrophysics Data System (ADS)

Visbal, Heidy; Fujiki, Satoshi; Aihara, Yuichi; Watanabe, Taku; Park, Youngsin; Doo, Seokgwang

2014-12-01

The influence of selected carbonate species on LiNi0.8Co0.15Al0.05O2 (NCA) surface for all-solid-state lithium-ion battery (ASSB) with a sulfide based solid electrolyte was studied for its electrochemical properties, structural stabilities, and surface characteristics. The rated discharge performance improved with the reduction of the carbonate concentration on the NCA surface due to the decrease of the interface resistance. The species and coordination of the adsorbed carbonates on the NCA surface were analyzed by diffuse reflectance Fourier transformed infrared (DRIFT) spectroscopy. The coordination of the adsorbed carbonate anion was determined based on the degree of splitting of the ν3(CO) stretching vibrations. It is found that the surface carbonate species exists in an unidentate coordination on the surface. They react with the sulfide electrolyte to form an irreversible passivation layer. This layer obstructs the charge transfer process at the cathode/electrolyte interface, and results in the rise of the interface resistance and drop of the rated discharge capability.

Preparing near-surface heavy oil for extraction using microbial degradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busche, Frederick D.; Rollins, John B.; Noyes, Harold J.

In one embodiment, the invention provides a system including at least one computing device for enhancing the recovery of heavy oil in an underground, near-surface crude oil extraction environment by performing a method comprising sampling and identifying microbial species (bacteria and/or fungi) that reside in the underground, near-surface crude oil extraction environment; collecting rock and fluid property data from the underground, near-surface crude oil extraction environment; collecting nutrient data from the underground, near-surface crude oil extraction environment; identifying a preferred microbial species from the underground, near-surface crude oil extraction environment that can transform the heavy oil into a lighter oil;more » identifying a nutrient from the underground, near-surface crude oil extraction environment that promotes a proliferation of the preferred microbial species; and introducing the nutrient into the underground, near-surface crude oil extraction environment.« less

Characterization of initial events in bacterial surface colonization by two Pseudomonas species using image analysis.

PubMed

Mueller, R F; Characklis, W G; Jones, W L; Sears, J T

1992-05-01

The processes leading to bacterial colonization on solid-water interfaces are adsorption, desorption, growth, and erosion. These processes have been measured individually in situ in a flowing system in real time using image analysis. Four different substrata (copper, silicon, 316 stainless-steel and glass) and 2 different bacterial species (Pseudomonas aeruginosa and Pseudomonas fluorescens) were used in the experiments. The flow was laminar (Re = 1.4) and the shear stress was kept constant during all experiments at 0.75 N m(-2). The surface roughness varied among the substrata from 0.002 microm (for silicon) to 0.015 microm (for copper). Surface free energies varied from 25.1 dynes cm(-1) for silicon to 31.2 dynes cm(-1) for copper. Cell curface hydrophobicity, reported as hydrocarbon partitioning values, ranged from 0.67 for Ps. fluorescens to 0.97 for Ps. aeruginosa.The adsorption rate coefficient varied by as much as a factor of 10 among the combinations of bacterial strain and substratum material, and was positively correlated with surface free energy, the surface roughness of the substratum, and the hydrophobicity of the cells. The probability of desorption decreased with increasing surface free energy and surface roughness of the substratum. Cell growth was inhibited on copper, but replication of cells overlying an initial cell layer was observed with increased exposure time to the cell-containing bulk water. A mathematical model describing cell accumulation on a substratum is presented.

Kernel Density Surface Modelling as a Means to Identify Significant Concentrations of Vulnerable Marine Ecosystem Indicators

PubMed Central

Kenchington, Ellen; Murillo, Francisco Javier; Lirette, Camille; Sacau, Mar; Koen-Alonso, Mariano; Kenny, Andrew; Ollerhead, Neil; Wareham, Vonda; Beazley, Lindsay

2014-01-01

The United Nations General Assembly Resolution 61/105, concerning sustainable fisheries in the marine ecosystem, calls for the protection of vulnerable marine ecosystems (VME) from destructive fishing practices. Subsequently, the Food and Agriculture Organization (FAO) produced guidelines for identification of VME indicator species/taxa to assist in the implementation of the resolution, but recommended the development of case-specific operational definitions for their application. We applied kernel density estimation (KDE) to research vessel trawl survey data from inside the fishing footprint of the Northwest Atlantic Fisheries Organization (NAFO) Regulatory Area in the high seas of the northwest Atlantic to create biomass density surfaces for four VME indicator taxa: large-sized sponges, sea pens, small and large gorgonian corals. These VME indicator taxa were identified previously by NAFO using the fragility, life history characteristics and structural complexity criteria presented by FAO, along with an evaluation of their recovery trajectories. KDE, a non-parametric neighbour-based smoothing function, has been used previously in ecology to identify hotspots, that is, areas of relatively high biomass/abundance. We present a novel approach of examining relative changes in area under polygons created from encircling successive biomass categories on the KDE surface to identify “significant concentrations” of biomass, which we equate to VMEs. This allows identification of the VMEs from the broader distribution of the species in the study area. We provide independent assessments of the VMEs so identified using underwater images, benthic sampling with other gear types (dredges, cores), and/or published species distribution models of probability of occurrence, as available. For each VME indicator taxon we provide a brief review of their ecological function which will be important in future assessments of significant adverse impact on these habitats here and elsewhere. PMID:25289667

Kernel density surface modelling as a means to identify significant concentrations of vulnerable marine ecosystem indicators.

PubMed

Kenchington, Ellen; Murillo, Francisco Javier; Lirette, Camille; Sacau, Mar; Koen-Alonso, Mariano; Kenny, Andrew; Ollerhead, Neil; Wareham, Vonda; Beazley, Lindsay

2014-01-01

The United Nations General Assembly Resolution 61/105, concerning sustainable fisheries in the marine ecosystem, calls for the protection of vulnerable marine ecosystems (VME) from destructive fishing practices. Subsequently, the Food and Agriculture Organization (FAO) produced guidelines for identification of VME indicator species/taxa to assist in the implementation of the resolution, but recommended the development of case-specific operational definitions for their application. We applied kernel density estimation (KDE) to research vessel trawl survey data from inside the fishing footprint of the Northwest Atlantic Fisheries Organization (NAFO) Regulatory Area in the high seas of the northwest Atlantic to create biomass density surfaces for four VME indicator taxa: large-sized sponges, sea pens, small and large gorgonian corals. These VME indicator taxa were identified previously by NAFO using the fragility, life history characteristics and structural complexity criteria presented by FAO, along with an evaluation of their recovery trajectories. KDE, a non-parametric neighbour-based smoothing function, has been used previously in ecology to identify hotspots, that is, areas of relatively high biomass/abundance. We present a novel approach of examining relative changes in area under polygons created from encircling successive biomass categories on the KDE surface to identify "significant concentrations" of biomass, which we equate to VMEs. This allows identification of the VMEs from the broader distribution of the species in the study area. We provide independent assessments of the VMEs so identified using underwater images, benthic sampling with other gear types (dredges, cores), and/or published species distribution models of probability of occurrence, as available. For each VME indicator taxon we provide a brief review of their ecological function which will be important in future assessments of significant adverse impact on these habitats here and elsewhere.

Using supramolecular binding motifs to provide precise control over the ratio and distribution of species in multiple component films grafted on surfaces: demonstration using electrochemical assembly from aryl diazonium salts.

PubMed

Gui, Alicia L; Yau, Hon Man; Thomas, Donald S; Chockalingam, Muthukumar; Harper, Jason B; Gooding, J Justin

2013-04-16

Supramolecular interactions between two surface modification species are explored to control the ratio and distribution of these species on the resultant surface. A binary mixture of aryl diazonium salts bearing oppositely charged para-substituents (either -SO3(-) or -N(+)(Me)3), which also reduce at different potentials, has been examined on glassy carbon surfaces using cyclic voltammetry and X-ray photoelectron spectroscopy (XPS). Striking features were observed: (1) the two aryl diazonium salts in the mixed solution undergo reductive adsorption at the same potential which is distinctively less negative than the potential required for the reduction of either of the two aryl diazonium salts alone; (2) the surface ratio of the two phenyl derivatives is consistently 1:1 regardless of the ratio of the two aryl diazonium salts in the modification solutions. Homogeneous distribution of the two oppositely charged phenyl species on the modified surface has also been suggested by XPS survey spectra. Diffusion coefficient measurements by DOSY NMR and DFT based computation have indicated the association of the two aryl diazonium species in the solution, which has led to changes in the molecular orbital energies of the two species. This study highlights the potential of using intermolecular interactions to control the assembly of multicomponent thin layers.

Effect of antifreeze protein on heterogeneous ice nucleation based on a two-dimensional random-field Ising model

NASA Astrophysics Data System (ADS)

Dong, Zhen; Wang, Jianjun; Zhou, Xin

2017-05-01

Antifreeze proteins (AFPs) are the key biomolecules that protect many species from suffering the extreme conditions. Their unique properties of antifreezing provide the potential of a wide range of applications. Inspired by the present experimental approaches of creating an antifreeze surface by coating AFPs, here we present a two-dimensional random-field lattice Ising model to study the effect of AFPs on heterogeneous ice nucleation. The model shows that both the size and the free-energy effect of individual AFPs and their surface coverage dominate the antifreeze capacity of an AFP-coated surface. The simulation results are consistent with the recent experiments qualitatively, revealing the origin of the surprisingly low antifreeze capacity of an AFP-coated surface when the coverage is not particularly high as shown in experiment. These results will hopefully deepen our understanding of the antifreeze effects and thus be potentially useful for designing novel antifreeze coating materials based on biomolecules.

Manipulation of the fertility of marsupials for conservation of endangered species and control of over-abundant populations.

PubMed

Mate, K E; Molinia, F C; Rodger, J C

1998-10-01

Marsupials present a dichotomy in population management; the numbers of many Australian marsupial species have declined due to loss of habitat, competition from introduced herbivores and predation by introduced carnivores, but other species have become locally overabundant in Australia or are introduced pests in New Zealand. The manipulation of reproduction offers the means to increase or decrease productivity; however, considerable fundamental research is required before reproductive technologies can be applied to marsupials. Marsupials differ from eutherian mammals in several aspects of their reproduction including sex differentiation, gamete function and endocrinology, as well as in the relative lengths of gestation and lactation. Although these differences present unique problems in the application of reproductive technologies to marsupials, they also present unique opportunities for marsupial-specific fertility control. This paper summarises the assisted breeding technologies currently being applied to marsupials including superovulation, artificial insemination, in vitro fertilization and gene banking; unique marsupial targets for contraceptive intervention including gamete production, sperm capacitation, gamete surface antigens and embryonic development; and some options for the delivery of contraceptive vaccines to marsupial populations.

Surface area-volume ratios in insects.

PubMed

Kühsel, Sara; Brückner, Adrian; Schmelzle, Sebastian; Heethoff, Michael; Blüthgen, Nico

2017-10-01

Body mass, volume and surface area are important for many aspects of the physiology and performance of species. Whereas body mass scaling received a lot of attention in the literature, surface areas of animals have not been measured explicitly in this context. We quantified surface area-volume (SA/V) ratios for the first time using 3D surface models based on a structured light scanning method for 126 species of pollinating insects from 4 orders (Diptera, Hymenoptera, Lepidoptera, and Coleoptera). Water loss of 67 species was measured gravimetrically at very dry conditions for 2 h at 15 and 30 °C to demonstrate the applicability of the new 3D surface measurements and relevance for predicting the performance of insects. Quantified SA/V ratios significantly explained the variation in water loss across species, both directly or after accounting for isometric scaling (residuals of the SA/V ∼ mass 2/3 relationship). Small insects with a proportionally larger surface area had the highest water loss rates. Surface scans of insects to quantify allometric SA/V ratios thus provide a promising method to predict physiological responses, improving the potential of body mass isometry alone that assume geometric similarity. © 2016 Institute of Zoology, Chinese Academy of Sciences.

Enhancing anaerobic digestion of complex organic waste with carbon-based conductive materials.

PubMed

Dang, Yan; Holmes, Dawn E; Zhao, Zhiqiang; Woodard, Trevor L; Zhang, Yaobin; Sun, Dezhi; Wang, Li-Ying; Nevin, Kelly P; Lovley, Derek R

2016-11-01

The aim of this work was to study the methanogenic metabolism of dog food, a food waste surrogate, in laboratory-scale reactors with different carbon-based conductive materials. Carbon cloth, carbon felt, and granular activated carbon all permitted higher organic loading rates and promoted faster recovery of soured reactors than the control reactors. Microbial community analysis revealed that specific and substantial enrichments of Sporanaerobacter and Methanosarcina were present on the carbon cloth surface. These results, and the known ability of Sporanaerobacter species to transfer electrons to elemental sulfur, suggest that Sporanaerobacter species can participate in direct interspecies electron transfer with Methanosarcina species when carbon cloth is available as an electron transfer mediator. Copyright © 2016 Elsevier Ltd. All rights reserved.

Vertical patterns of ichthyoplankton at the interface between a temperate estuary and adjacent coastal waters: Seasonal relation to diel and tidal cycles

NASA Astrophysics Data System (ADS)

Primo, Ana Lígia; Azeiteiro, Ulisses M.; Marques, Sónia C.; Ré, Pedro; Pardal, Miguel A.

2012-07-01

Vertical distribution and migration pattern of ichthyoplankton assemblage in the Mondego estuary were investigated in relation to diel and tidal cycle. Summer and winter communities were sampled, at surface and bottom, over a diel cycle during spring and neap tides at a fixed station at the mouth of the estuary. Summer presented higher larvae density mainly of Pomatoschistus spp., Gobius niger and Parablennius pilicornis. Main species in winter assemblages were Pomatoschistus spp. and Sardina pilchardus. There were no differences between depth stratums across diel or tide cycle. Nevertheless, main species larval densities showed significant periodic variation associated with tide (M2) and diel (K1) cycles presenting generally, higher density at night and around low tide. Conversely, vertical patterns observed could not be related with diel or tidal cycle. Tough, main species presented some extent of vertical migration. Vertical patterns observed appear to be related to seasonal stratification and river flow, increasing amplitude during periods of less stratification and lower water currents. Present study provides a better understanding of ichthyoplankton vertical movement patterns and of small scale dynamics at the interface of two coastal European systems.

Pollenkitt wetting mechanism enables species-specific tunable pollen adhesion.

PubMed

Lin, Haisheng; Gomez, Ismael; Meredith, J Carson

2013-03-05

Plant pollens are microscopic particles exhibiting a remarkable breadth of complex solid surface features. In addition, many pollen grains are coated with a viscous liquid, "pollenkitt", thought to play important roles in pollen dispersion and adhesion. However, there exist no quantitative studies of the effects of solid surface features or pollenkitt on adhesion of pollen grains, and it remains unclear what role these features play in pollen adhesion and transport. We report AFM adhesion measurements of five pollen species with a series of test surfaces in which each pollen has a unique solid surface morphology and pollenkitt volume. The results indicate that the combination of surface morphology (size and shape of echinate or reticulate features) with the pollenkitt volume provides pollens with a remarkably tunable adhesion to surfaces. With pollenkitt removed, pollen grains had relatively low adhesion strengths that were independent of surface chemistry and scalable with the tip radius of the pollen's ornamentation features, according to the Hamaker model. With the pollenkitt intact, adhesion was up to 3-6 times higher than the dry grains and exhibited strong substrate dependence. The adhesion enhancing effect of pollenkitt was driven by the formation of pollenkitt capillary bridges and was surprisingly species-dependent, with echinate insect-pollinated species (dandelion and sunflower) showing significantly stronger adhesion and higher substrate dependence than wind-pollinated species (ragweed, poplar, and olive). The combination of high pollenkitt volume and large convex, spiny surface features in echinate entomophilous varieties appears to enhance the spreading area of the liquid pollenkitt relative to varieties of pollen with less pollenkitt volume and less pronounced surface features. Measurements of pollenkitt surface energy indicate that the adhesive strength of capillary bridges is primarily dependent on nonpolar van der Waals interactions, with some contribution from the Lewis basic component of surface energy.

In situ spectroscopic evidence for neptunium(V)-carbonate inner-sphere and outer-sphere ternary surface complexes on hematite surfaces.

PubMed

Arai, Yuji; Moran, P B; Honeyman, B D; Davis, J A

2007-06-01

Np(V) surface speciation on hematite surfaces at pH 7-9 under pC2 = 10(-3.45) atm was investigated using X-ray absorption spectroscopy (XAS). In situ XAS analyses suggest that bis-carbonato inner-sphere and tris-carbonato outer-sphere ternary surface species coexist at the hematite-water interface at pH 7-8.8, and the fraction of outer-sphere species gradually increases from 27 to 54% with increasing pH from 7 to 8.8. The results suggest that the heretofore unknown Np(V)-carbonato ternary surface species may be important in predicting the fate and transport of Np(V) in the subsurface environment down gradient of high-level nuclear waste respositories.

Analysis of Titan's neutral upper atmosphere from Cassini Ion Neutral Mass Spectrometer measurements in the Closed Source Neutral mode

NASA Astrophysics Data System (ADS)

Cui, Jun

In this thesis I present an in-depth study of the distribution of various neutral species in Titan's upper atmosphere, at altitudes between 950 and 1,500 km for abundant species (N 2 , CH 4 as well as their isotopes) and between 950 and 1,200 km for most minor species. However, the study of the H 2 distribution on Titan is extended to an altitude as high as 6,000 km in the exosphere. The analysis is based on a large sample of Cassini/INMS (Ion Neutral Mass Spectrometer) measurements in the CSN (Closed Source Neutral) mode, obtained during 15 close flybys of Titan. The densities of abundant species including N 2 , CH 4 and H 2 are determined directly from their main channels. However, to untangle the overlapping cracking patterns of minor species, the technique of Singular Value Decomposition (SVD) is used to determine simultaneously the densities of various hydrocarbons, nitriles and oxygen compounds. All minor species except for 40 Ar present density enhancements measured during the outbound legs. This can be interpreted as a result of wall effects, which could be either adsorption/desorption or heterogeneous surface chemistry on the chamber walls. In the thesis, I use a simple model to describe the observed time behavior of minor species. Results on their atmospheric abundances are provided both in terms of direct inbound measurements assuming ram pressure enhancement and values corrected for wall adsorption/desorption. Among all minor species of photochemical interest, the INMS data provide direct observational evidences for C 2 H 2 , C 2 H 4 , C 2 H 6 , CH 3 C 2 H, C 4 H 2 , C 6 H 6 , HC 3 N and C 2 N 2 in Titan's upper atmosphere. Upper limits are put for other minor species. The globally averaged distribution of N 2 , CH 4 and H 2 are each modeled with the diffusion approximation. The N 2 profile suggests an average thermospheric temperature of 154 K. The CH 4 and H 2 distribution constrains their fluxes to be 3.0 × 10 9 cm -2 s -1 and 1.3 × 10 10 cm -2 s -1 , referred to Titan's surface. The H 2 escape flux is about a factor of ~3 higher than the Jeans value, which is interpreted as enhanced thermal escape driven primarily by an upward conductive heat flux. Such a conclusion is based on kinetic model calculations in the 13-moment approximation that require energy continuity at the upper boundary. On the other hand, a proper interpretation of the observed CH 4 escape has to rely on the detailed nonthermal processes, which are still unknown at the present time. The INMS observations of the nitrogen isotope ratio implies 14 N/ 15 N=131.6 near Titan's surface. The profile of carbon isotope ratio combining INMS and GCMS results implies that both CH 4 and its isotope escape from Titan's exobase with roughly the same drift velocity, in contrast to the Jeans case which requires that CH 4 escapes with a much larger velocity due to its smaller mass. The INMS data also suggest horizontal/diurnal variations of temperature and neutral gas distribution in Titan's thermosphere. The equatorial regions, the ramside, as well as the nightside hemisphere of Titan appear to be warmer and present some evidences for the depletion of light species such as CH 4 . Meridional variations of most heavy species are also observed, with a trend of depletion toward the north pole. Though some of the above variations might be interpreted by either the solar-driven models or plasma-driven models, a physical scenario that reconciles all the observed horizontal/diurnal variations in a consistent way is still missing, With a careful evaluation of the effect of restricted sampling, some of the features shown in the INMS data are more likely to be observational biases.

CURVATURE-DRIVEN MOLECULAR FLOW ON MEMBRANE SURFACE*

PubMed Central

MIKUCKI, MICHAEL; ZHOU, Y. C.

2017-01-01

This work presents a mathematical model for the localization of multiple species of diffusion molecules on membrane surfaces. Morphological change of bilayer membrane in vivo is generally modulated by proteins. Most of these modulations are associated with the localization of related proteins in the crowded lipid environments. We start with the energetic description of the distributions of molecules on curved membrane surface, and define the spontaneous curvature of bilayer membrane as a function of the molecule concentrations on membrane surfaces. A drift-diffusion equation governs the gradient flow of the surface molecule concentrations. We recast the energetic formulation and the related governing equations by using an Eulerian phase field description to define membrane morphology. Computational simulations with the proposed mathematical model and related numerical techniques predict (i) the molecular localization on static membrane surfaces at locations with preferred mean curvatures, and (ii) the generation of preferred mean curvature which in turn drives the molecular localization. PMID:29056778

On predicting contamination levels of HALOE optics aboard UARS using direct simulation Monte Carlo

NASA Technical Reports Server (NTRS)

Woronowicz, Michael S.; Rault, Didier F. G.

1993-01-01

A three-dimensional version of the direct simulation Monte Carlo method is adapted to assess the contamination environment surrounding a highly detailed model of the Upper Atmosphere Research Satellite. Emphasis is placed on simulating a realistic, worst-case set of flowfield and surface conditions and geometric orientations in order to estimate an upper limit for the cumulative level of volatile organic molecular deposits at the aperture of the Halogen Occultation Experiment. Problems resolving species outgassing and vent flux rates that varied over many orders of magnitude were handled using species weighting factors. Results relating to contaminant cloud structure, cloud composition, and statistics of simulated molecules impinging on the target surface are presented, along with data related to code performance. Using procedures developed in standard contamination analyses, the cumulative level of volatile organic deposits on HALOE's aperture over the instrument's 35-month nominal data collection period is estimated to be about 2700A.

Identification of the psaA Gene, Coding for Pneumococcal Surface Adhesin A, in Viridans Group Streptococci other than Streptococcus pneumoniae

PubMed Central

Jado, Isabel; Fenoll, Asunción; Casal, Julio; Pérez, Amalia

2001-01-01

The gene encoding the pneumococcal surface adhesin A (PsaA) protein has been identified in three different viridans group streptococcal species. Comparative studies of the psaA gene identified in different pneumococcal isolates by sequencing PCR products showed a high degree of conservation among these strains. PsaA is encoded by an open reading frame of 930 bp. The analysis of this fragment in Streptococcus mitis, Streptococcus oralis, and Streptococcus anginosus strains revealed a sequence identity of 95, 94, and 90%, respectively, to the corresponding open reading frame of the previously reported Streptococcus pneumoniae serotype 6B strain. Our results confirm that psaA is present and detectable in heterologous bacterial species. The possible implications of these results for the suitability and potential use of PsaA in the identification and diagnosis of pneumococcal diseases are discussed. PMID:11527799

Investigation of the rates of surface and bulk ROS-generating reactions using indigo dye as an indicator

NASA Astrophysics Data System (ADS)

Anderson, Carly; Clark, Douglas; Graves, David

2014-10-01

We present evidence for the existence of two distinct processes that contribute to the generation of reactive oxygen and nitrogen species (RONS) in liquids exposed to cold atmospheric plasma (CAP) in air. At the plasma-liquid interface, there exists a fast surface reaction zone where RONS from the gas phase interact with species in the liquid. RONS can also be produced by ``slow'' chemical reactions in the bulk liquid, even long after plasma exposure. To separate the effects of these processes, we used indigo dye as an indicator of ROS production; specifically generation of hydroxyl radical. The rate of indigo decolorization while in direct contact with CAP is compared with the expected rate of hydroxyl radical generation at the liquid surface. When added to aqueous solutions after CAP exposure, indigo dye reacts on a time scale consistent with the production of peroxynitrous acid, ONOOH, which is known to decompose to hydroxyl radical below a pH of 6.8. In this study, the CAP used was a air corona discharge plasma run in a positive streamer mode.

Calculations of neoclassical impurity transport in stellarators

NASA Astrophysics Data System (ADS)

Mollén, Albert; Smith, Håkan M.; Langenberg, Andreas; Turkin, Yuriy; Beidler, Craig D.; Helander, Per; Landreman, Matt; Newton, Sarah L.; García-Regaña, José M.; Nunami, Masanori

2017-10-01

The new stellarator Wendelstein 7-X has finished the first operational campaign and is restarting operation in the summer 2017. To demonstrate that the stellarator concept is a viable candidate for a fusion reactor and to allow for long pulse lengths of 30 min, i.e. ``quasi-stationary'' operation, it will be important to avoid central impurity accumulation typically governed by the radial neoclassical transport. The SFINCS code has been developed to calculate neoclassical quantities such as the radial collisional transport and the ambipolar radial electric field in 3D magnetic configurations. SFINCS is a cutting-edge numerical tool which combines several important features: the ability to model an arbitrary number of kinetic plasma species, the full linearized Fokker-Planck collision operator for all species, and the ability to calculate and account for the variation of the electrostatic potential on flux surfaces. In the present work we use SFINCS to study neoclassical impurity transport in stellarators. We explore how flux-surface potential variations affect the radial particle transport, and how the radial electric field is modified by non-trace impurities and flux-surface potential variations.

Aquifers survey in the context of source rocks exploitation: from baseline acquisition to long term monitoring

NASA Astrophysics Data System (ADS)

Garcia, Bruno; Rouchon, Virgile; Deflandre, Jean-Pierre

2017-04-01

Producing hydrocarbons from source rocks (like shales: a mix of clays, silts, carbonate and sandstone minerals containing matured organic matter, i.e. kerogen oil and gas, but also non-hydrocarbon various species of chemical elements including sometimes radioactive elements) requires to create permeability within the rock matrix by at least hydraulically fracturing the source rock. It corresponds to the production of hydrocarbon fuels that have not been naturally expelled from the pressurized matured source rock and that remain trapped in the porosity or/and kerogen porosity of the impermeable matrix. Azimuth and extent of developed fractures can be respectively determined and mapped by monitoring the associated induced microseismicity. This allows to have an idea of where and how far injected fluids penetrated the rock formation. In a geological context, aquifers are always present in the vicinity -or on fluid migration paths- of such shale formations: deep aquifers (near the shale formation) up to sub-surface and potable (surface) aquifers. Our purpose will be to track any unsuitable invasion or migration of chemicals specifies coming from matured shales of production fluids including both drilling and fracturing ones into aquifers. Our objective is to early detect and alarm of any anomaly to avoid any important environmental issue. The approach consists in deploying a specific sampling tool within a well to recover formation fluids and to run a panoply of appropriate laboratory tests to state on fluid characteristics. Of course for deep aquifers, such a characterization process may consider aquifer properties prior producing shale oil and gas, as they may contain naturally some chemical species present in the source rocks. One can also consider that a baseline acquisition could be justified in case of possible previous invasion of non-natural fluids in the formation under survey (due to any anthropogenic action at surface or in the underground). The paper aims at presenting the protocol and routine test we propose to make our early detection approach efficient for production of shale hydrocarbon fluids, in considering the source-rock reservoir itself, the aquifers, and also the chemical species present in the fluids that are used for hydraulic fracturing operations.

Molecular dynamics simulation of sodium aluminosilicate glass structures and glass surface-water reactions using the reactive force field (ReaxFF)

NASA Astrophysics Data System (ADS)

Dongol, R.; Wang, L.; Cormack, A. N.; Sundaram, S. K.

2018-05-01

Reactive potentials are increasingly used to study the properties of glasses and glass water reactions in a reactive molecular dynamics (MD) framework. In this study, we have simulated a ternary sodium aluminosilicate glass and investigated the initial stages of the glass surface-water reactions at 300 K using reactive force field (ReaxFF). On comparison of the simulated glass structures generated using ReaxFF and classical Buckingham potentials, our results show that the atomic density profiles calculated for the surface glass structures indicate a bond-angle distribution dependency. The atomic density profiles also show higher concentrations of non-bridging oxygens (NBOs) and sodium ions at the glass surface. Additionally, we present our results of formation of silanol species and the diffusion of water molecules at the glass surface using ReaxFF.

Interactions of N,N'-dimethylaminoethanol with steel surfaces in alkaline and chlorine containing solutions

NASA Astrophysics Data System (ADS)

Welle, A.; Liao, J. D.; Kaiser, K.; Grunze, M.; Mäder, U.; Blank, N.

1997-10-01

Formulations based on dilute aqueous solutions of N,N'-dimethylethanolamine (DMEA) are used to protect reinforcement steel bars ('rebar') in concrete from corrosion. In a previous paper we discussed the usefulness of X-ray photoelectron spectroscopy (XPS) to detect DMEA adsorbed from solution and the application of secondary neutral mass spectrometry (SNMS) to study migration of DMEA through a cement matrix. In this report we present XPS data of DMEA adsorbed on steel surfaces from alkaline and chlorine containing solutions of variable concentration range and discuss models for the interaction of DMEA with the oxidized steel surface and the mechanism of corrosion inhibition of DMEA. DMEA is strongly bonded to the steel surface and displaces ionic species from the substrate/solution interface hence protecting the ironoxide surface from ionic attack.

Real-time observation of the dehydrogenation processes of methanol on clean Ru(001) and Ru(001)-p(2×2) O surfaces by a temperature-programmed electron-stimulated desorption ion angular distribution/time-of-flight system

NASA Astrophysics Data System (ADS)

Sasaki, Takehiko; Itai, Yuichiro; Iwasawa, Yasuhiro

1999-12-01

Decomposition processes of methanol on clean and oxygen-precovered Ru(001) surfaces have been visualized in real time with a temperature-programmed (TP) electron-stimulated desorption ion angular distribution (ESDIAD)/time-of-flight (TOF) system. The mass of desorbed ions during temperature-programmed surface processes was identified by TOF measurements. In the case of methanol (CH 3OD) adsorption on Ru(001)-p(2×2)-O, a halo pattern of H + from the methyl group of methoxy species was observed at 100-200 K, followed by a broad pattern from the methyl group at 230-250 K and by a near-center pattern from O + ions originating from adsorbed CO above 300 K. The halo pattern is attributed to a perpendicular conformation of the CO bond axis of the methoxy species, leading to off-normal CH bond scission. On the other hand, methanol adsorbed on clean Ru(001) did not give any halo pattern but a broad pattern was observed along the surface normal, indicating that the conformation of the methoxy species is not ordered on the clean surface. Comparison between the ESDIAD images of the oxygen-precovered surface and the clean surface suggests that the precovered oxygen adatoms induce ordering of the methoxy species. Real-time ESDIAD measurements revealed that the oxygen atoms at the Ru(001)-p(2×2)-O surface have a positive effect on selective dehydrogenation of the methoxy species to CO+H 2 and a blocking effect on CO bond breaking of the methoxy species.

Numerical investigation of the spatiotemporal distribution of chemical species in an atmospheric surface barrier-discharge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasan, M. I.; Walsh, J. L., E-mail: jlwalsh@liverpool.ac.uk

Using a one dimensional time dependent convection-reaction-diffusion model, the temporal and spatial distributions of species propagating downstream of an atmospheric pressure air surface barrier discharge was studied. It was found that the distribution of negatively charged species is more spatially spread compared to positive ions species, which is attributed to the diffusion of electrons that cool down and attach to background gas molecules, creating different negative ions downstream of the discharge region. Given the widespread use of such discharges in applications involving the remote microbial decontamination of surfaces and liquids, the transport of plasma generated reactive species away from themore » discharge region was studied by implementing mechanical convection through the discharge region. It was shown that increased convection causes the spatial distribution of species density to become uniform. It was also found that many species have a lower density close to the surface of the discharge as convection prevents their accumulation. While for some species, such as NO{sub 2}, convection causes a general increase in the density due to a reduced residence time close to the discharge region, where it is rapidly lost through reactions with OH. The impact of the applied power was also investigated, and it was found that the densities of most species, whether charged or neutral, are directly proportional to the applied power.« less

Results of 30-year-old plantations on surface mines in the Central States

Treesearch

W. Clark Ashby; Clay A. Kolar; Nelson F. Rogers

1980-01-01

Twenty-eight tree species have grown successfully on surface-mined lands in the Central States. Variability in species performance can be related to geographic area, type of rooting medium, and associated species. Many planted stands have been vigorously invaded by volunteer trees, as well as by other plants and animals.

Microbial Community Analysis of Naturally Durable Wood in an Above Ground Field Test

Treesearch

G.T. Kirker; S.V. Diehl; P.K. Lebow

2014-01-01

This paper presents preliminary results of an above ground field test wherein eight naturally durable wood species were exposed concurrently at two sites in North America. Surface samples were taken at regular intervals from non-durable controls and compared to their more durable counterparts. Terminal Restriction Fragment Length Polymorphism was performed to...

Study of SRM Critical Surfaces Using Near Infrared Optical Fiber Spectrometry

NASA Technical Reports Server (NTRS)

Workman, G. L.; Hughes, C.; Arendale, W. A.

1997-01-01

The measurement and control of cleanliness for critical surfaces during manufacturing and in service operations provides a unique challenge in the current thrust for environmentally benign processes. Of particular interest has been work performed in maintaining quality in the production of bondline surfaces in propulsion systems and the identification of possible contaminants which are detrimental to the integrity of the bondline. This work requires an in-depth study of the possible sources of contamination, methodologies to identify contaminants, discrimination between contaminants and chemical species caused by environment, and the effect of particular contaminants on the bondline integrity of the critical surfaces. This paper will provide an introduction to the use of Near Infrared (NIR) optical fiber spectrometry in a nondestructive measurement system for process monitoring and how it can be used to help clarify issues concerning surface chemistry. In a previous conference, experimental results for quantitative measurement of silicone and Conoco HD2 greases, and tape residues on solid rocket motor surfaces were presented. This paper will present data for metal hydroxides and discuss the use of the integrating sphere to minimize the effects of physical properties of the surfaces (such as surface roughness) on the results obtained from the chemometric methods used for quantitative analysis.

Ecological impacts of wheat seeding after a Sierra Nevada wildfire

USGS Publications Warehouse

Keeley, Jon E.

2004-01-01

The Highway Fire burned 1680 ha of mixed ponderosa pine–oak–chaparral in the newly created Giant Sequoia National Monument and the adjacent Sequoia National Forest of Fresno County, California in August 2001. The USDA Forest Service Burned Area Emergency Rehabilitation (BAER) program recommended that portions of the burned forest be seeded with a non-persistent variety of wheat at a density of 157 kg ha–1 (140 lb/ac). The present study compared the vascular plant diversity and cover in seeded and unseeded parts of this burn to evaluate the ecological impact of seeding an alien grass. In the first post-fire growing season, the natural regeneration of unseeded control sites averaged ~55% ground surface covered. Wheat seeding enhanced the ground cover, averaging 95% ground surface cover. Wheat was the dominant species on the seeded sites, comprising 67% of the total cover. Dominance–diversity curves were markedly affected by the seeding and indicated a disruption in the natural ecological structure of these communities. On seeded sites, wheat dominated and all other species were poorly represented whereas, on unseeded control sites, there was a more equitable distribution of species. Correlated with the wheat cover was a significant decrease in species richness at all scales examined. Total species richness was reduced from 152 species across all unseeded sites to 104 species on all seeded sites. Average species richness, at scales from 1 to 1000 m2, was 30–40% lower on seeded sites. Species most strongly inhibited were post-fire endemics whose lifecycle is restricted to immediate post-fire environments. Seeded sites had fewer alien species than unseeded sites; however, this may not have any lasting effect since other studies show the primary alien threat is not in the first post-fire year. Seeding was also associated with an order of magnitude drop in Pinus ponderosa seedling recruitment and, coupled with the massive thatch still remaining on the site, it is likely that recruitment will be inhibited in subsequent years.

How sedge meadow soils, microtopography, and vegetation respond to sedimentation

USGS Publications Warehouse

Werner, K.J.; Zedler, Joy B.

2002-01-01

The expansion of urban and agricultural activities in watersheds of the Midwestern USA facilitates the conversion of species-rich sedge meadows to stands of Phalaris arundinacea and Typha spp. We document the role of sediment accumulation in this process based on field surveys of three sedge meadows dominated by Carex stricta, their adjacent Phalaris or Typha stands, and transitions from Carex to these invasive species. The complex microtopography of Carex tussocks facilitates the occurrence of other native species. Tussock surface area and species richness were positively correlated in two marshes (r2 = 0.57 and 0.41); on average, a 33-cm-tall tussock supported 7.6 species. Phalaris also grew in tussock form in wetter areas but did not support native species. We found an average of 10.5 Carex tussocks per 10-m transect, but only 3.5 Phalaris tussocks. Microtopographic relief, determined with a high-precision GPS, measured 11% greater in Carex meadows than Phalaris stands. Inflowing sediments reduced microtopographic variation and surface area for native species. We calculated a loss of one species per 1000 cm2 of lost tussock surface area, and loss of 1.2 species for every 10-cm addition of sediment over the sedge meadow surface. Alluvium overlying the sedge meadow soil had a smaller proportion of organic matter content and higher dry bulk density than the buried histic materials. We conclude that sedimentation contributes to the loss of native species in remnant wetlands. ?? 2002, The Society of Wetland Scientists.

Conjugate Analysis of Two-Dimensional Ablation and Pyrolysis in Rocket Nozzles

NASA Astrophysics Data System (ADS)

Cross, Peter G.

The development of a methodology and computational framework for performing conjugate analyses of transient, two-dimensional ablation of pyrolyzing materials in rocket nozzle applications is presented. This new engineering methodology comprehensively incorporates fluid-thermal-chemical processes relevant to nozzles and other high temperature components, making it possible, for the first time, to rigorously capture the strong interactions and interdependencies that exist between the reacting flowfield and the ablating material. By basing thermal protection system engineering more firmly on first principles, improved analysis accuracy can be achieved. The computational framework developed in this work couples a multi-species, reacting flow solver to a two-dimensional material response solver. New capabilities are added to the flow solver in order to be able to model unique aspects of the flow through solid rocket nozzles. The material response solver is also enhanced with new features that enable full modeling of pyrolyzing, anisotropic materials with a true two-dimensional treatment of the porous flow of the pyrolysis gases. Verification and validation studies demonstrating correct implementation of these new models in the flow and material response solvers are also presented. Five different treatments of the surface energy balance at the ablating wall, with increasing levels of fidelity, are investigated. The Integrated Equilibrium Surface Chemistry (IESC) treatment computes the surface energy balance and recession rate directly from the diffusive fluxes at the ablating wall, without making transport coefficient or unity Lewis number assumptions, or requiring pre-computed surface thermochemistry tables. This method provides the highest level of fidelity, and can inherently account for the effects that recession, wall temperature, blowing, and the presence of ablation product species in the boundary layer have on the flowfield and ablation response. Multiple decoupled and conjugate ablation analysis studies for the HIPPO nozzle test case are presented. Results from decoupled simulations show sensitivity to the wall temperature profile used within the flow solver, indicating the need for conjugate analyses. Conjugate simulations show that the thermal response of the nozzle is relatively insensitive to the choice of the surface energy balance treatment. However, the surface energy balance treatment is found to strongly affect the surface recession predictions. Out of all the methods considered, the IESC treatment produces surface recession predictions with the best agreement to experimental data. These results show that the increased fidelity provided by the proposed conjugate ablation modeling methodology produces improved analysis accuracy, as desired.

A DFT Investigation of the Mechanism of Propene Ammoxidation over α-Bismuth Molybdate

DOE PAGES

Licht, Rachel B.; Bell, Alexis T.

2016-11-17

We investigated the mechanisms and energetics for the propene oxidation and ammoxidation occurring on the (010) surface of Bi 2 Mo 3 O 12 using density functional theory (DFT). An energetically feasible sequence of elementary steps for propene oxidation to acrolein, propene ammoxidation to acrylonitrile, and acrolein ammoxidation to acrylonitrile is proposed. Consistent with experimental findings, the rate-limiting step for both propene oxidation and ammoxidation is the initial hydrogen abstraction from the methyl group of propene, which is calculated to have an apparent activation energy of 27.3 kcal/mol. The allyl species produced in this reaction is stabilized as an allylmore » alkoxide, which can then undergo hydrogen abstraction to form acrolein or react with ammonia adsorbed on under-coordinated surface Bi 3+ cations to form allylamine. Dehydrogenation of allylamine is shown to produce acrylonitrile, whereas reaction with additional adsorbed ammonia leads to the formation of acetonitrile and hydrogen cyanide. The dehydrogenation of allyalkoxide species is found to have a significantly higher activation barrier than reaction with adsorbed ammonia, consistent with the observation that very little acrolein is produced when ammonia is present. Finally, we found that rapid reoxidation of the catalyst surface to release wate the driving force for all reactions involving the cleavage of C-H or N-H bonds, because practically all of these steps are endothermic. (Chemical Equation Presented).« less

On-Surface Synthesis and Reactivity of Functional Organic and Metal-Organic Adsorbates at Metal Surfaces by Vibrational Spectroscopy

NASA Astrophysics Data System (ADS)

Williams, Christopher Glen

Surface self-assembly is a promising way to introduce functionality to a surface through design at the molecular level. These self-assembled species allow for new on-surface type reactions to be observed and studied. The experiments described in this thesis demonstrate that the molecules used in self-assembly can potentially lead to interesting synthesis pathways and can be used to explore previously under-researched reaction pathways and surface molecular architecture activity or stability. Alkanes are an unreactive species typically used for driving molecular assembly in surface structures. However, with molecular design, alkanes are capable of reacting on surfaces not typically associated with alkane reactivity. Utilizing high-resolution electron energy loss spectroscopy (HREELS) and octaethylporphyrin, we could observe that dehydrogenation is possible on Cu(100) and Ag(111) surfaces at 500 and 610 K respectively. HREELS revealed that after the dehydrogenation, the molecule undergoes an intramolecular C-C bond formation leading to a tetrabenzo-porphyrin structure. Controls with deposited tetrabenzo-porphyrin were performed to verify the structure. This work provides the first example of dehydrocyclization on Cu(100) and Ag(111) to be analyzed by vibrational spectroscopy. Alkyl species in the 1,3,5-tris-(3,5-diethylphenyl)benzene molecule also undergo a dehydrogenation on Cu(100) and Au(111) at 450 and 500 K. The design of this molecule does not let the intramolecular dehydrocyclization reaction take place, but instead the dehydrogenation leads to intermolecular C-C bond formation between molecular species as noted by the formation of extended structure across the surface. Controls with triphenyl-benzene were done to help characterize the peaks in the spectra and observe varying reactivity when the ethyl groups are absent. The fabrication of uniform single-site metal centers at surfaces is important for higher selectivity in next-generation heterogeneous catalysts. We accomplished this by metal coordination to redox non-innocent dipyridyl-tetrazine ligands. We utilize HREELS to observe a surface confined redox process of dipyridyl-tetrazine with V, Fe, Ag, and Pt. With the formation of the V-dipyridyl-tetrazine species, we are able to see that oxygen exposures to the surface results in a more selective vanadyl species formation as opposed to the multiple binding conformations observed with metallic vanadium nanoparticles. This thesis also reveals that the metal substrate used does not play a passive role with the metal-organic complex. Instead, we are the first to characterize a replacement of the coordinating metal species with atoms from the Ag(111) substrate. This replacement results in the redox reaction between the coordinating metal species and the substrate metal.

Influence of Marangoni flows on the dynamics of isothermal A + B → C reaction fronts.

PubMed

Tiani, R; Rongy, L

2016-09-28

The nonlinear dynamics of A + B → C fronts is analyzed both numerically and theoretically in the presence of Marangoni flows, i.e., convective motions driven by surface tension gradients. We consider horizontal aqueous solutions where the three species A, B, and C can affect the surface tension of the solution, thereby driving Marangoni flows. The resulting dynamics is studied by numerically integrating the incompressible Navier-Stokes equations coupled to reaction-diffusion-convection (RDC) equations for the three chemical species. We show that the dynamics of the front cannot be predicted solely on the basis of the one-dimensional reaction-diffusion profiles as is the case for buoyancy-driven convection around such fronts. We relate this observation to the structure of Marangoni flows which lead to more complex and exotic dynamics. We find in particular the surprising possibility of a reversal of the front propagation direction in time for some sets of Marangoni numbers, quantifying the influence of each chemical species concentration on the solution surface tension. We explain this reversal analytically and propose a new classification of the convective effects on A + B → C reaction fronts as a function of the Marangoni numbers. The influence of the layer thickness on the RDC dynamics is also presented. Those results emphasize the importance of flow symmetry properties when studying convective front dynamics in a given geometry.

Characterization of the surfaces of platinum/tin oxide based catalysts by Fourier Transform Infrared Spectroscopy (FTIR)

NASA Technical Reports Server (NTRS)

Keiser, Joseph T.; Upchurch, Billy T.

1990-01-01

A Pt/SnO2 catalyst has been developed at NASA Langley that is effective for the oxidation of CO at room temperature (1). A mechanism has been proposed to explain the effectiveness of this catalyst (2), but most of the species involved in this mechanism have not been observed under actual catalytic conditions. A number of these species are potentially detectable by Fourier Transform Infrared Spectroscopy (FTIR), e.g., HOSnO sub x, HO sub y PtO sub z, Pt-CO, and SnHCO3. Therefore a preliminary investigation was conducted to determine what might be learned about this particular catalyst by transmission FTIR. The main advantage of FTIR for this work is that the catalyst can be examined under conditions similar to the actual catalytic conditions. This can be of critical importance since some surface species may exist only when the reaction gases are present. Another advantage of the infrared approach is that since vibrations are probed, subtle chemical details may be obtained. The main disadvantage of this approach is that FTIR is not nearly as sensitive as the Ultra High Vacuum (UHV) surface analytical techniques such as Auger, Electron Spectroscopy for Chemical Analysis (ESCA), Electron Energy Loss Spectroscopy (EELS), etc. Another problem is that the assignment of the observed infrared bands may be difficult.

Sanitary quality, occurrence and identification of Staphylococcus sp. in food services.

PubMed

de Mello, Jozi Fagundes; da Rocha, Laura Braga; Lopes, Ester Souza; Frazzon, Jeverson; da Costa, Marisa

2014-01-01

Sanitary conditions are essential for the production of meals and control of the presence of pathogensis important to guarantee the health of customers. The aim of this study was to evaluate the sanitary quality of food services by checking the presence of thermotolerant coliforms, Staphylococcus sp. and evaluate the toxigenic potential from the latter. The analysis was performed on water, surfaces, equipment, ready-to-eat foods, hands and nasal cavity of handlers in seven food services. The water used in food services proved to be suitable for the production of meals. Most food, equipment and surfaces showed poor sanitary conditions due to the presence of thermotolerant coliforms (60.6%). Twenty-six Staphylococcus species were identified from the 121 Staphylococcus isolates tested. Staphylococci coagulase-negative species were predominant in the foods, equipment and surfaces. In food handlers and foods, the predominant species was Staphylococcus epidermidis. Twelve different genotypes were found after PCR for the classical enterotoxin genes. The seb gene (19.8%) was the most prevalent among all Staphylococcus sp. Both coagulase-positive and coagulase-negative Staphylococci showed some of the genes of the enterotoxins tested. We conclude that there are hygienic and sanitary deficiencies in the food services analyzed. Although coagulase-positive Staphylococci have not been present in foods there is a wide dispersion of enterotoxigenic coagulase-negative Staphylococci in the environment and in the foods analyzed, indicating a risk to consumer health.

Evolution of anthropogenic emissions at the global and regional scale during the past three decades

NASA Astrophysics Data System (ADS)

Granier, C.; Bessagnet, B. B.; Bond, T. C.; D'Angiola, A.; Denier van der Gon, H.; Frost, G. J.; Heil, A.; Kaiser, J.; Kinne, S. A.; Klimont, Z.; Kloster, S.; Lamarque, J.; Liousse, C.; Masui, T.; Meleux, F.; Mieville, A.; Ohara, T.; Raut, J.; Riahi, K.; Schultz, M. G.; Smith, S.; Thomson, A. M.; van Aardenne, J.; van der Werf, G.; van Vuuren, D.

2010-12-01

The knowledge of the distributions of surface emissions of gases and aerosols is essential for an accurate modeling and analysis of the distribution and evolution of the concentration of gaseous and particulate chemical species. The quantification of surface fluxes by source of origin is furthermore central to the assessment of effects and the development of control measures. Over the past few years, different ranges of emission fluxes have been proposed by several studies, which have provided emissions at different spatial and temporal scales. We have compared the emissions of several chemical compounds, i.e. carbon monoxide, nitrogen oxides, sulfur dioxide and black carbon, as provided by global and regional emissions inventories in different regions of the world for the past thirty years. The presentation will focus on the United States, Europe and China. Significant differences between the datasets providing emissions in these regions have been identified, reaching for example 60% and 35% for anthropogenic emissions of carbon monoxide and nitrogen oxides in both regions, respectively. We will assess the current uncertainties on surface emissions and their recent trends. This analysis is often hindered because of differences in base years and in species considered in the different datasets. Current work aiming at compiling comparable metrics for such species for the analysis of regional and global emission datasets will be discussed.

Sanitary quality, occurrence and identification of Staphylococcus sp. in food services

PubMed Central

de Mello, Jozi Fagundes; da Rocha, Laura Braga; Lopes, Ester Souza; Frazzon, Jeverson; da Costa, Marisa

2014-01-01

Sanitary conditions are essential for the production of meals and control of the presence of pathogensis important to guarantee the health of customers. The aim of this study was to evaluate the sanitary quality of food services by checking the presence of thermotolerant coliforms, Staphylococcus sp. and evaluate the toxigenic potential from the latter. The analysis was performed on water, surfaces, equipment, ready-to-eat foods, hands and nasal cavity of handlers in seven food services. The water used in food services proved to be suitable for the production of meals. Most food, equipment and surfaces showed poor sanitary conditions due to the presence of thermotolerant coliforms (60.6%). Twenty-six Staphylococcus species were identified from the 121 Staphylococcus isolates tested. Staphylococci coagulase-negative species were predominant in the foods, equipment and surfaces. In food handlers and foods, the predominant species was Staphylococcus epidermidis. Twelve different genotypes were found after PCR for the classical enterotoxin genes. The seb gene (19.8%) was the most prevalent among all Staphylococcus sp. Both coagulase-positive and coagulase-negative Staphylococci showed some of the genes of the enterotoxins tested. We conclude that there are hygienic and sanitary deficiencies in the food services analyzed. Although coagulase-positive Staphylococci have not been present in foods there is a wide dispersion of enterotoxigenic coagulase-negative Staphylococci in the environment and in the foods analyzed, indicating a risk to consumer health. PMID:25477940

Studies on the surface modification of TiN coatings using MEVVA ion implantation with selected metallic species

NASA Astrophysics Data System (ADS)

Ward, L. P.; Purushotham, K. P.; Manory, R. R.

2016-02-01

Improvement in the performance of TiN coatings can be achieved using surface modification techniques such as ion implantation. In the present study, physical vapor deposited (PVD) TiN coatings were implanted with Cr, Zr, Nb, Mo and W using the metal evaporation vacuum arc (MEVVA) technique at a constant nominal dose of 4 × 1016 ions cm-2 for all species. The samples were characterized before and after implantation, using Rutherford backscattering (RBS), glancing incident angle X-ray diffraction (GIXRD), atomic force microscopy (AFM) and optical microscopy. Friction and wear studies were performed under dry sliding conditions using a pin-on-disc CSEM Tribometer at 1 N load and 450 m sliding distance. A reduction in the grain size and surface roughness was observed after implantation with all five species. Little variation was observed in the residual stress values for all implanted TiN coatings, except for W implanted TiN which showed a pronounced increase in compressive residual stress. Mo-implanted samples showed a lower coefficient of friction and higher resistance to breakdown during the initial stages of testing than as-received samples. Significant reduction in wear rate was observed after implanting with Zr and Mo ions compared with unimplanted TiN. The presence of the Ti2N phase was observed with Cr implantation.

Measurements of Polyatomic Molecule Formation on an Icy Grain Analog Using Fast Atoms

NASA Technical Reports Server (NTRS)

Chutjian, A.; Madsunkov, S.; Shortt, B. J.; MacAskill, J. A.; Darrach, M. R.

2006-01-01

Carbon dioxide has been produced from the impact of a monoenergetic O(P-3) beam upon a surface cooled to 4.8 K and covered with a CO ice. Using temperature-programmed desorption and mass spectrometer detection, we have detected increasing amounts of CO2 formation with O(P-3) energies of 2, 5, 10, and 14 eV. This is the first measurement of polyatomic molecule formation on a surface with superthermal atoms. The goal of this work is to detect other polyatomic species, such as CH3OH, which can be formed under conditions that simulate the grain temperature, surface coverage, and superthermal atoms present in shock-heated circumstellar and interstellar regions.

Surface enhanced Raman scattering on Tardigrada--towards monitoring and imaging molecular structures in live cryptobiotic organisms.

PubMed

Kneipp, Harald; Møbjerg, Nadja; Jørgensen, Aslak; Bohr, Henrik G; Hélix-Nielsen, Claus; Kneipp, Janina; Kneipp, Katrin

2013-10-01

Tardigrades are microscopic metazoans which are able to survive extreme physical and chemical conditions by entering a stress tolerant state called cryptobiosis. At present, the molecular mechanisms behind cryptobiosis are still poorly understood. We show that surface enhanced Raman scattering supported by plasmonic gold nanoparticles can measure molecular constituents and their local distribution in live tardigrades. Surface enhanced Raman signatures allow to differentiate between two species and indicate molecular structural differences between tardigrades in water and in a dry state. This opens new avenues for exploring cryptobiosis by studying molecular changes in live cryptobiotic organisms. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

SJL-1, a C-type lectin, acts as a surface defense molecule in Japanese sea cucumber, Apostichopus japonicus.

PubMed

Ono, Keisuke; Suzuki, Takuya Alan; Toyoshima, Youichi; Suzuki, Tomoya; Tsutsui, Shigeyuki; Odaka, Tomoyuki; Miyadai, Toshiaki; Nakamura, Osamu

2018-05-01

The surface defense molecules of aquatic invertebrates against infectious microorganisms have remained largely unexplored. In the present study, hemagglutinins were isolated from an extract of body surface layer of Japanese sea cucumber, Apostichopus japonicus, by affinity chromatography with fixed rabbit erythrocyte membranes. The N-terminal sequence of a 15-kDa agglutinin was almost identical with that of SJL-1, a C-type lectin formerly identified in this species. Because cDNA sequence and tissue distribution of SJL-1 have not been reported, we performed cDNA sequencing, gene expression analysis, and western blotting and immunohistochemical evaluation with anti-recombinant SJL-1 (rSJL-1) antibodies. The hemagglutinin gene was transcribed mainly in the integument, tentacles, and respiratory tree. Western blotting revealed that SJL-I is present in a body surface rinse, indicating that SJL-1 is secreted onto the body surface. SJL-1-positive cells scattered beneath the outermost layer of the integument were detected by immunohistochemistry. Furthermore, rSJL-1 agglutinated Gram-positive and Gram-negative bacteria, and yeast. These results indicate that SJL-1 acts as a surface defense molecule in A. japonicus. Copyright © 2018 Elsevier Ltd. All rights reserved.

Measuring the role of seagrasses in regulating sediment surface elevation

USGS Publications Warehouse

Potouroglou, Maria; Bull, James C.; Krauss, Ken W.; Kennedy, Hilary A.; Fusi, Marco; Daffonchio, Daniele; Mangora, Mwita M.; Githaiga, Michael N.; Diele, Karen; Huxham, Mark

2017-01-01

Seagrass meadows provide numerous ecosystem services and their rapid global loss may reduce human welfare as well as ecological integrity. In common with the other ‘blue carbon’ habitats (mangroves and tidal marshes) seagrasses are thought to provide coastal defence and encourage sediment stabilisation and surface elevation. A sophisticated understanding of sediment elevation dynamics in mangroves and tidal marshes has been gained by monitoring a wide range of different sites, located in varying hydrogeomorphological conditions over long periods. In contrast, similar evidence for seagrasses is sparse; the present study is a contribution towards filling this gap. Surface elevation change pins were deployed in four locations, Scotland, Kenya, Tanzania and Saudi Arabia, in both seagrass and unvegetated control plots in the low intertidal and shallow subtidal zone. The presence of seagrass had a highly significant, positive impact on surface elevation at all sites. Combined data from the current work and the literature show an average difference of 31 mm per year in elevation rates between vegetated and unvegetated areas, which emphasizes the important contribution of seagrass in facilitating sediment surface elevation and reducing erosion. This paper presents the first multi-site study for sediment surface elevation in seagrasses in different settings and species.

Measuring the role of seagrasses in regulating sediment surface elevation.

PubMed

Potouroglou, Maria; Bull, James C; Krauss, Ken W; Kennedy, Hilary A; Fusi, Marco; Daffonchio, Daniele; Mangora, Mwita M; Githaiga, Michael N; Diele, Karen; Huxham, Mark

2017-09-20

Seagrass meadows provide numerous ecosystem services and their rapid global loss may reduce human welfare as well as ecological integrity. In common with the other 'blue carbon' habitats (mangroves and tidal marshes) seagrasses are thought to provide coastal defence and encourage sediment stabilisation and surface elevation. A sophisticated understanding of sediment elevation dynamics in mangroves and tidal marshes has been gained by monitoring a wide range of different sites, located in varying hydrogeomorphological conditions over long periods. In contrast, similar evidence for seagrasses is sparse; the present study is a contribution towards filling this gap. Surface elevation change pins were deployed in four locations, Scotland, Kenya, Tanzania and Saudi Arabia, in both seagrass and unvegetated control plots in the low intertidal and shallow subtidal zone. The presence of seagrass had a highly significant, positive impact on surface elevation at all sites. Combined data from the current work and the literature show an average difference of 31 mm per year in elevation rates between vegetated and unvegetated areas, which emphasizes the important contribution of seagrass in facilitating sediment surface elevation and reducing erosion. This paper presents the first multi-site study for sediment surface elevation in seagrasses in different settings and species.

Ce, Ti modified MCM-48 mesoporous photocatalysts: Effect of the synthesis route on support and metal ion properties

NASA Astrophysics Data System (ADS)

Mureseanu, Mihaela; Filip, Mihaela; Somacescu, Simona; Baran, Adriana; Carja, Gabriela; Parvulescu, Viorica

2018-06-01

New Ti-MCM-48 and CeTi-MCM-48 photocatalysts were obtained by impregnation of the MCM-48 silica support synthesized by a hydrothermal process with aqueous solution of Ti and Ce precursors. The immobilization of metal cations presented a low effect on the porosity, morphology and structure of MCM-48 mesoporous silica support as was evidenced by N2 adsorption-desorption, X-ray diffraction, SEM and TEM electron microscopy. EDAX analysis and X-ray photoelectron microscopy (XPS) indicated that titanium cations were present on the mesoporous silica surface only as Ti4+ species and the effect of ceria on titanium speciation was different, compared to the CeTi-MCM-48 sample, previously obtained by direct synthesis. The photocatalytic properties of mono- and bimetallic catalysts were evaluated in degradation of phenol from water and correlated with the active metallic species concentration, distribution, speciation and their interaction with the support or each other. An advanced oxidation mechanism for phenol degradation by radical species was proposed.

Tailored zeolites for the removal of metal oxyanions: overcoming intrinsic limitations of zeolites.

PubMed

Figueiredo, Hugo; Quintelas, Cristina

2014-06-15

This review aims to present a global view of the efforts conducted to convert zeolites into efficient supports for the removal of heavy metal oxyanions. Despite lacking affinity for these species, due to inherent charge repulsion between zeolite framework and anionic species, zeolites have still received considerable attention from the scientific community, since their versatility allowed tailoring them to answer specific requirements. Different processes for the removal and recovery of toxic metals based on zeolites have been presented. These processes resort to modification of the zeolite surface to allow direct adsorption of oxyanions, or by combination with reducing agents for oxyanions that allow ion-exchange with the converted species by the zeolite itself. In order to testify zeolite versatility, as well as covering the wide array of physicochemical constraints that oxyanions offer, chromium and arsenic oxyanions were selected as model compounds for a review of treatment/remediation strategies, based on zeolite modification. Copyright © 2014 Elsevier B.V. All rights reserved.

Morphological diversity and function of the stigma in Ficus species (Moraceae)

NASA Astrophysics Data System (ADS)

Teixeira, Simone Pádua; Costa, Marina F. B.; Basso-Alves, João Paulo; Kjellberg, Finn; Pereira, Rodrigo A. S.

2018-07-01

The stigma plays several roles such as pollen hydration and selection, and pollen tube nutrition. In the Ficus-fig wasp mutualism, stigmata have an additional, almost unknown, function by representing a physical interface for both plant and wasp reproduction. We used light and electron microscopy to compare the detailed morphology of the stigmata of nine Ficus species of different sections and with different pollination modes and sexual expressions. Figs were collected at the stage when the stigmata were receptive for pollination. Stigmata in actively pollinated monoecious species have well developed papillae concentrated on the adaxial surface exposed towards the fig cavity. Conversely, the passively pollinated monoecious species have the whole surface of the stigmata covered by somewhat smaller papillae. In both actively and passively pollinated monoecious species these features are consistent, irrespective of style length. In all actively pollinated gynodioecious species, the stigmata of pistillate flowers were tubular or infundibuliform whereas in almost all actively pollinated monoecious species (except F. racemosa) the stigmata were filiform, with one branch or two asymmetric branches. In gynodioecious species the short-styled flowers in "male" figs show a limited receptive surface with small papillae, while the stigmata of long-styled flowers in "female" figs are covered by papillae that extend down the sides of the style, increasing the stigmatic surface. In actively pollinated species, stigmata are cohesive, forming a common surface for pollen tube germination (= synstigma). The synstigma arrangement was quite variable: lax, cohesive or very cohesive, with entanglement by stigmatic papillae and stylar trichomes. Entanglement by stylar trichomes is common in gynodioecious species. The synstigma arrangement did not correlate with phylogeny or breeding system. This study is the first to report a very loose synstigma in actively pollinated monoecious Ficus species. Our analyses revealed that, in Ficus, the synstigma is functionally analogous to an extra-gynoecial compitum. Comparative studies will be required to test further hypotheses about the evolutionary determinants of such variation.

Air-snow interaction of nitrogen species in the polar regions

NASA Astrophysics Data System (ADS)

Cutting Thakur, Roseline; Thamban, Meloth

2017-04-01

The previous studies in the polar regions have frequently compared ion concentration of nitrogen species in snow and aerosol, neglecting to discuss the fact that snow could also scavenge chemical compounds in the gas phase. Further, Peroxyacetyl nitrate (PAN(g)) which is a reactive nitrogen oxide and constitutes ˜90% of the total NOy in the higher altitudes has very scarce measurements in Antarctica and higher altitude areas. The present study reports the interaction of gaseous PAN(g) and HNO3(g)species with NO3- in aerosols and surface snow, in different meteorological conditions at both Antarctic and Arctic regions. Trace gases were sampled through the denuder tubes followed by a Teflon filter to collect the aerosol species and analyzed through the Ion Chromatography technique. Simultaneous snow measurements were also carried out near the air sampling site, close to the Polar Indian research stations. Samples were collected over a period of 15 days in January-February, 2014 in Larsemann Hills, East Antarctica, and 9 days during April, 2012 in Ny- Ålesund, Arctic. Obervations suggest that during high temperature, high radiation and high humidity conditions HNO3(g) concentration decrease with a simultaneous increase in aerosol NO3- [NO3- (A)] in both the regions. It implies that HNO3(g) converts to NO3-(A) probably through the reaction with sea-salt aerosols leading to the formation NO3- in aerosols. Further, the NO3- aerosol-snow interaction is also strong in these conditions. Such associations suggested that, dry deposition of nitrate aerosol could be a source of snow nitrate [NO3- (S)]. Further, a decrease of PAN(g)concentration with a simultaneous increase in NO3-(A) suggested that PAN(g) undergoes photolytic conversion to form NO2(g) and HNO3(g), which may further hydrolyze to form NO3-(A) due to high humidity conditions. However, this mechanism was not dominant during low temperature and low radiation conditions in both the regions, rather a direct gaseous exchange was found to influence the NO3-(S) concentration. Since, HNO3(g) is a highly water soluble and strong acid with a strong affinity to ice, the increasing humidity facilitates the adsorption of HNO3(g)on the snow surface, thereby, increasing the NO3-(S). In such conditions, PAN(g) concentration also decreased with a simultaneous increase in NO3- (S) indicating that direct PAN(g) adsorption on surface snow could be an additional source of NO3-(S). HNO3(g) being a more sticky gas than any other gaseous nitrogen species was scavenged more than PAN(g) on the snow surface. The precipitation events in the Antarctic and Arctic regions increases the concentration of NO3-(S) nearly 2-10 fold, with a simultaneous decrease of NO3-(A) and gaseous HNO3(g) and PAN(g) concentration. This strongly suggests that during precipitation events gaseous as well as particulate scavenging of nitrogen species could be significant. This study suggests that apart from the dry deposition of aerosol species on the snow surface and the outward fluxes of gaseous species from the snow surface, the direct gaseous adsorption of trace gases on the snow surface also needs to be critically evaluated, before computing the nitrogen budget in the polar regions.

Real-time plasma control in a dual-frequency, confined plasma etcher

NASA Astrophysics Data System (ADS)

Milosavljević, V.; Ellingboe, A. R.; Gaman, C.; Ringwood, J. V.

2008-04-01

The physics issues of developing model-based control of plasma etching are presented. A novel methodology for incorporating real-time model-based control of plasma processing systems is developed. The methodology is developed for control of two dependent variables (ion flux and chemical densities) by two independent controls (27 MHz power and O2 flow). A phenomenological physics model of the nonlinear coupling between the independent controls and the dependent variables of the plasma is presented. By using a design of experiment, the functional dependencies of the response surface are determined. In conjunction with the physical model, the dependencies are used to deconvolve the sensor signals onto the control inputs, allowing compensation of the interaction between control paths. The compensated sensor signals and compensated set-points are then used as inputs to proportional-integral-derivative controllers to adjust radio frequency power and oxygen flow to yield the desired ion flux and chemical density. To illustrate the methodology, model-based real-time control is realized in a commercial semiconductor dielectric etch chamber. The two radio frequency symmetric diode operates with typical commercial fluorocarbon feed-gas mixtures (Ar/O2/C4F8). Key parameters for dielectric etching are known to include ion flux to the surface and surface flux of oxygen containing species. Control is demonstrated using diagnostics of electrode-surface ion current, and chemical densities of O, O2, and CO measured by optical emission spectrometry and/or mass spectrometry. Using our model-based real-time control, the set-point tracking accuracy to changes in chemical species density and ion flux is enhanced.

Functional & phylogenetic diversity of copepod communities

NASA Astrophysics Data System (ADS)

Benedetti, F.; Ayata, S. D.; Blanco-Bercial, L.; Cornils, A.; Guilhaumon, F.

2016-02-01

The diversity of natural communities is classically estimated through species identification (taxonomic diversity) but can also be estimated from the ecological functions performed by the species (functional diversity), or from the phylogenetic relationships among them (phylogenetic diversity). Estimating functional diversity requires the definition of specific functional traits, i.e., phenotypic characteristics that impact fitness and are relevant to ecosystem functioning. Estimating phylogenetic diversity requires the description of phylogenetic relationships, for instance by using molecular tools. In the present study, we focused on the functional and phylogenetic diversity of copepod surface communities in the Mediterranean Sea. First, we implemented a specific trait database for the most commonly-sampled and abundant copepod species of the Mediterranean Sea. Our database includes 191 species, described by seven traits encompassing diverse ecological functions: minimal and maximal body length, trophic group, feeding type, spawning strategy, diel vertical migration and vertical habitat. Clustering analysis in the functional trait space revealed that Mediterranean copepods can be gathered into groups that have different ecological roles. Second, we reconstructed a phylogenetic tree using the available sequences of 18S rRNA. Our tree included 154 of the analyzed Mediterranean copepod species. We used these two datasets to describe the functional and phylogenetic diversity of copepod surface communities in the Mediterranean Sea. The replacement component (turn-over) and the species richness difference component (nestedness) of the beta diversity indices were identified. Finally, by comparing various and complementary aspects of plankton diversity (taxonomic, functional, and phylogenetic diversity) we were able to gain a better understanding of the relationships among the zooplankton community, biodiversity, ecosystem function, and environmental forcing.

Cyanobacteria breakthrough: Effects of Limnothrix redekei contamination in an artificial bank filtration on a regional water supply.

PubMed

Rose, Adam K; Fabbro, Larelle; Kinnear, Susan

2018-06-01

Mitigation of cyanobacterial or "blue-green algal" blooms is a challenging task for water managers across Australia. In the present study, a regional drinking water source (located in Central Queensland) was studied to identify the potential risks posed by cyanobacteria. Data were collected from the drinking water source (a lagoon) as well as the drinking water supply infrastructure, at monthly intervals between September 2012 and December 2014. In March 2013 there was an extreme rainfall event where floodwaters infiltrated the water supply without passing through bank filtration. The floodwaters also compromised the bank filtration via erosion. The pump well and bank filtration system were subsequently upgraded/maintained in May 2013. Results showed that following the extreme event and infrastructure upgrade, two distinct Limnothrix redekei blooms microscopically identified, were detected in the drinking water supply chain. Further investigations indicated that the species was also present in the pump well infrastructure, a dark environment, growing on the surface of the newly installed pump well cement pipe. After observing the occurrence and habitat niche of this species during the present study, a suggestion was made to minimise cyanobacterial contamination and proliferation within the water supply chain infrastructure. The preliminary proposal is to use clean sand on the sub-surface layer of the bank filtration, complemented with biologically active sand as a surface cap. Furthermore, the culturing techniques reported in this study can potentially be used to optimize assessment for Limnothrix redekei populations surrounding water extraction points. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of replacing a hydroxyl group with a methyl group on arsenic (V) species adsorption on goethite (alpha-FeOOH).

PubMed

Zhang, J S; Stanforth, R S; Pehkonen, S O

2007-02-01

Arsenate and methylated arsenicals, such as dimethylarsinate (DMA) and monomethylarsonate (MMA), are being found with increasing frequency in natural water systems. The mobility and bioavailability of these arsenic species in the environment are strongly influenced by their interactions with mineral surface, especially iron and aluminum oxides. Goethite (alpha-FeOOH), one of the most abundant ferric (hydr)oxides in natural systems, has a high retention capacity for arsenic species. Unfortunately, the sorption mechanism for the species is not completely understood, which limits our ability to model their behavior in natural systems. The purpose of this study is to investigate the effect of replacing a hydroxyl group with a methyl group on the adsorption behaviors of arsenic (V) species using adsorption edges, the influence of the background electrolyte on arsenic adsorption, and their effect on the zeta potential of goethite. The affinity of the three species to the goethite surface decreases in the order of AsO4=MMA>DMA. The uptake of DMA and MMA is independent of the concentration of background electrolyte, indicating that both species form inner-sphere complexes on the goethite surface and the most charge of adsorbed DMA and MMA locates at the surface plane. Arsenate uptake increases with increasing concentrations of background electrolyte at pH above 4, possibly due to that the charge of adsorbed arsenate is distributed between the surface plane and another electrostatic plane. DMA and lower concentrations of MMA have small effect on the zeta potential, whereas the zeta potential of goethite decreases in the presence of arsenate. The small effect on zeta potential of DMA or MMA adsorption suggests that the sorption sites for the anions is not important in controlling the surface charge. This observation is inconsistent with most adsorption models that postulate a singly coordinated hydroxyls contributing to both the adsorption and the surface charge, but supports the thesis that the charge on the goethite surface comes primarily from protonation of the triply bound oxygen atoms on the surface.

High field electron paramagnetic resonance spectroscopy under ultrahigh vacuum conditions—A multipurpose machine to study paramagnetic species on well defined single crystal surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rocker, J.; Cornu, D.; Kieseritzky, E.

2014-08-01

A new ultrahigh vacuum (UHV) electron paramagnetic resonance (EPR) spectrometer operating at 94 GHz to investigate paramagnetic centers on single crystal surfaces is described. It is particularly designed to study paramagnetic centers on well-defined model catalysts using epitaxial thin oxide films grown on metal single crystals. The EPR setup is based on a commercial Bruker E600 spectrometer, which is adapted to ultrahigh vacuum conditions using a home made Fabry Perot resonator. The key idea of the resonator is to use the planar metal single crystal required to grow the single crystalline oxide films as one of the mirrors of themore » resonator. EPR spectroscopy is solely sensitive to paramagnetic species, which are typically minority species in such a system. Hence, additional experimental characterization tools are required to allow for a comprehensive investigation of the surface. The apparatus includes a preparation chamber hosting equipment, which is required to prepare supported model catalysts. In addition, surface characterization tools such as low energy electron diffraction (LEED)/Auger spectroscopy, temperature programmed desorption (TPD), and infrared reflection absorption spectroscopy (IRAS) are available to characterize the surfaces. A second chamber used to perform EPR spectroscopy at 94 GHz has a room temperature scanning tunneling microscope attached to it, which allows for real space structural characterization. The heart of the UHV adaptation of the EPR experiment is the sealing of the Fabry-Perot resonator against atmosphere. To this end it is possible to use a thin sapphire window glued to the backside of the coupling orifice of the Fabry Perot resonator. With the help of a variety of stabilization measures reducing vibrations as well as thermal drift it is possible to accumulate data for a time span, which is for low temperature measurements only limited by the amount of liquid helium. Test measurements show that the system can detect paramagnetic species with a density of approximately 5 × 10{sup 11} spins/cm{sup 2}, which is comparable to the limit obtained for the presently available UHV-EPR spectrometer operating at 10 GHz (X-band). Investigation of electron trapped centers in MgO(001) films shows that the increased resolution offered by the experiments at W-band allows to identify new paramagnetic species, that cannot be differentiated with the currently available methodology.« less

Repurposing doxycycline for synucleinopathies: remodelling of α-synuclein oligomers towards non-toxic parallel beta-sheet structured species

PubMed Central

González-Lizárraga, Florencia; Socías, Sergio B.; Ávila, César L.; Torres-Bugeau, Clarisa M.; Barbosa, Leandro R. S.; Binolfi, Andres; Sepúlveda-Díaz, Julia E.; Del-Bel, Elaine; Fernandez, Claudio O.; Papy-Garcia, Dulce; Itri, Rosangela; Raisman-Vozari, Rita; Chehín, Rosana N.

2017-01-01

Synucleinophaties are progressive neurodegenerative disorders with no cure to date. An attractive strategy to tackle this problem is repurposing already tested safe drugs against novel targets. In this way, doxycycline prevents neurodegeneration in Parkinson models by modulating neuroinflammation. However, anti-inflammatory therapy per se is insufficient to account for neuroprotection. Herein we characterise novel targets of doxycycline describing the structural background supporting its effectiveness as a neuroprotector at subantibiotic doses. Our results show that doxycycline reshapes α-synuclein oligomers into off-pathway, high-molecular-weight species that do not evolve into fibrils. Off-pathway species present less hydrophobic surface than on-pathway oligomers and display different β-sheet structural arrangement. These structural changes affect the α-synuclein ability to destabilize biological membranes, cell viability, and formation of additional toxic species. Altogether, these mechanisms could act synergically giving novel targets for repurposing this drug. PMID:28155912

Yeast diversity isolated from grape musts during spontaneous fermentation from a Brazilian winery.

PubMed

Bezerra-Bussoli, Carolina; Baffi, Milla Alves; Gomes, Eleni; Da-Silva, Roberto

2013-09-01

Saccharomyces and non-Saccharomyces yeast species from a winery located in Brazil were identified by ribosomal gene-sequencing analysis. A total of 130 yeast strains were isolated from grape surfaces and musts during alcoholic fermentation from Isabel, Bordeaux, and Cabernet Sauvignon varieties. Samples were submitted to PCR-RFLP analysis and genomic sequencing. Thirteen species were identified: Candida quercitrusa, Candida stellata, Cryptococcus flavescens, Cryptococcus laurentii, Hanseniaspora uvarum, Issatchenkia occidentalis, Issatchenkia orientalis, Issatchenkia terricola, Pichia kluyveri, Pichia guilliermondii, Pichia sp., Saccharomyces cerevisiae, and Sporidiobolus pararoseus. A sequential substitution of species during the different stages of fermentation, with a dominance of non-Saccharomyces yeasts at the beginning, and a successive replacement of species by S. cerevisiae strains at the final steps were observed. This is the first report about the yeast distribution present throughout the alcoholic fermentation in a Brazilian winery, providing supportive information for future studies on their contribution to wine quality.

Dubinectes infirmus, a new species of deep-water Munnopsidae (Crustacea, Isopoda, Asellota) from the Argentine Basin, South Atlantic Ocean

PubMed Central

Malyutina, Marina; Brandt, Angelika

2011-01-01

Abstract Dubinectes infirmus sp. n., Munnopsidae, is described from the Argentine Basin, southwest Atlantic, at depths between 4586–4607 m. The new species is distinguished by a narrow rim of the pleotelson posterior margin which is not raising over its dorsal surface; article 3 of the antennula is subequal in length to article 2; distomedial lobes of male pleopod 1 are of same size as distolateral lobes; stylet of male pleopod 2 is subequal in length to protopod; uropod exopod is more than a half of endopod length. Some generic characters which are weakly pronounced in the new species or have different state are defined more precisely in the revised diagnosis of Dubinectes. The modified diagnosis of the genus, a key to the species of Dubinectes as well as the distribution of the genus are presented. PMID:22207784

Canopies to Continents: What spatial scales are needed to represent landcover distributions in earth system models?

NASA Astrophysics Data System (ADS)

Guenther, A. B.; Duhl, T.

2011-12-01

Increasing computational resources have enabled a steady improvement in the spatial resolution used for earth system models. Land surface models and landcover distributions have kept ahead by providing higher spatial resolution than typically used in these models. Satellite observations have played a major role in providing high resolution landcover distributions over large regions or the entire earth surface but ground observations are needed to calibrate these data and provide accurate inputs for models. As our ability to resolve individual landscape components improves, it is important to consider what scale is sufficient for providing inputs to earth system models. The required spatial scale is dependent on the processes being represented and the scientific questions being addressed. This presentation will describe the development a contiguous U.S. landcover database using high resolution imagery (1 to 1000 meters) and surface observations of species composition and other landcover characteristics. The database includes plant functional types and species composition and is suitable for driving land surface models (CLM and MEGAN) that predict land surface exchange of carbon, water, energy and biogenic reactive gases (e.g., isoprene, sesquiterpenes, and NO). We investigate the sensitivity of model results to landcover distributions with spatial scales ranging over six orders of magnitude (1 meter to 1000000 meters). The implications for predictions of regional climate and air quality will be discussed along with recommendations for regional and global earth system modeling.

Surface speciation and interactions between adsorbed chloride and water on cerium dioxide

NASA Astrophysics Data System (ADS)

Sutherland-Harper, Sophie; Taylor, Robin; Hobbs, Jeff; Pimblott, Simon; Pattrick, Richard; Sarsfield, Mark; Denecke, Melissa; Livens, Francis; Kaltsoyannis, Nikolas; Arey, Bruce; Kovarik, Libor; Engelhard, Mark; Waters, John; Pearce, Carolyn

2018-06-01

Ceria particles with different specific surface areas (SSA) were contaminated with chloride and water, then heat treated at 500 and 900 °C to investigate sorption behaviour of these species on metal oxides. Results from x-ray photoelectron spectroscopy and infrared spectroscopy showed chloride and water adsorption onto particles increased with surface area and that these species were mostly removed on heat treatment (from 6.3 to 0.8 at% Cl- on high SSA and from 1.4 to 0.4 at% on low SSA particles). X-ray diffraction revealed that chloride was not incorporated into the bulk ceria structure, but crystal size increased upon contamination. Ce LIII-edge x-ray absorption spectroscopy confirmed that chloride was not present in the first co-ordination sphere around Ce(IV) ions, so was not bonded to Ce as chloride in the bulk structure. Sintering of contaminated high SSA particles occurred with heat treatment at 900 °C, and they resembled low SSA particles synthesised at this temperature. Physical chloride-particle interactions were investigated using electron microscopy and energy dispersive x-ray analysis, showing that chloride was homogeneously distributed on ceria and that reduction of porosity did not trap surface-sorbed chloride inside the particles as surface area was reduced during sintering. This has implications for stabilisation of chloride-contaminated PuO2 for long term storage.

Geochemical modeling of mercury speciation in surface water and implications on mercury cycling in the everglades wetland.

PubMed

Jiang, Ping; Liu, Guangliang; Cui, Wenbin; Cai, Yong

2018-06-01

The geochemical model PHREEQC, abbreviated from PH (pH), RE (redox), EQ (equilibrium), and C (program written in C), was employed on the datasets generated by the USEPA Everglades Regional Environmental Monitoring and Assessment Program (R-EMAP) to determine the speciation distribution of inorganic mercury (iHg) in Everglades water and to explore the implications of iHg speciation on mercury cycling. The results suggest that sulfide and DOM were the key factors that regulate inorganic Hg speciation in the Everglades. When sulfide was present at measurable concentrations (>0.02 mg/L), Hg-S complexes dominated iHg species, occurring in the forms of HgS 2 2- , HgHS 2 - , and Hg(HS) 2 that were affected by a variety of environmental factors. When sulfide was assumed nonexistent, Hg-DOM complexes occurred as the predominant Hg species, accounting for almost 100% of iHg species. However, when sulfide was presumably present at a very low, environmentally relevant concentration (3.2 × 10 -7  mg/L), both Hg-DOM and Hg-S complexes were present as the major iHg species. These Hg-S species and Hg-DOM complex could be related to methylmercury (MeHg) in environmental matrices such floc, periphyton, and soil, and the correlations are dependent upon different circumstances (e.g., sulfide concentrations). The implications of the distribution of iHg species on MeHg production and fate in the Everglades were discussed. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of atmospheric oxidative plasma treatments on polypropylenic fibers surface: Characterization and reaction mechanisms

NASA Astrophysics Data System (ADS)

Nisticò, Roberto; Magnacca, Giuliana; Faga, Maria Giulia; Gautier, Giovanna; D'Angelo, Domenico; Ciancio, Emanuele; Lamberti, Roberta; Martorana, Selanna

2013-08-01

Atmospheric pressure plasma-dielectric barrier discharge (APP-DBD, open chamber configuration) was used to functionalize polypropylene (PP) fibers surface in order to generate oxidized-reactive groups such as hydroperoxides, alcohols and carbonyl species (i.e. ketones and others). Such a species increased the surface polarity, without causing material degradation. Three different types of plasma mixture (He, He/O2, He/O2/H2O) under three different values of applied power (750, 1050, 1400 W) were investigated. The formed plasma species (O2+, O single atom and OH radical) and their distribution were monitored via optical emission spectrometry (OES) measurements, and the plasma effects on PP surface species formation were followed by X-ray photoemission spectroscopy (XPS). Results allowed to better understand the reaction pathways between plasma phase and PP fibers. In fact, two reaction mechanisms were proposed, the first one concerning the plasma phase reactions and the second one involving material surface modifications.

Reactions of Atmospheric Species with Clean and H, C, and O Implanted Species

DTIC Science & Technology

1989-07-27

energy shifts of the XFS core level spectra. Atomic concentration measurements were used to estimate the surface compositions. These results are...of the target surface, desorption of adsorbate atoms by hyperthermal physical/chemical interaction, and accumulation of a high surface concentration ...8217chemrical interactiosn, and accumulation of a high surface concentration of the pruijettile spCies. Vi1 film depsistion t-hcse studies investigate the

Stages of polymer transformation during remote plasma oxidation (RPO) at atmospheric pressure

NASA Astrophysics Data System (ADS)

Luan, P.; Oehrlein, G. S.

2018-04-01

The interaction of cold temperature plasma sources with materials can be separated into two types: ‘direct’ and ‘remote’ treatments. Compared to the ‘direct’ treatment which involves energetic charged species along with short-lived, strongly oxidative neutral species, ‘remote’ treatment by the long-lived weakly oxidative species is less invasive and better for producing uniformly treated surfaces. In this paper, we examine the prototypical case of remote plasma oxidation (RPO) of polymer materials by employing a surface micro-discharge (in a N2/O2 mixture environment) treatment on polystyrene. Using material characterization techniques including real-time ellipsometry, x-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy, the time evolution of polymer film thickness, refractive index, surface, and bulk chemical composition were evaluated. These measurements revealed three consecutive stages of polymer transformation, i.e. surface adsorption and oxidation, bulk film permeation and thickness expansion followed by the material removal as a result of RPO. By correlating the observed film thickness changes with simultaneously obtained chemical information, we found that the three stages were due to the three effects of weakly oxidative species on polymers: (1) surface oxidation and nitrate (R-ONO2) chemisorption, (2) bulk oxidation, and (3) etching. Our results demonstrate that surface adsorption and oxidation, bulk oxidation, and etching can all happen during one continuous plasma treatment. We show that surface nitrate is only adsorbed on the top few nanometers of the polymer surface. The polymer film expansion also provided evidence for the diffusion and reaction of long-lived plasma species in the polymer bulk. Besides, we found that the remote plasma etched surface was relatively rich in O-C=O (ester or carboxylic acid). These findings clarify the roles of long-lived weakly oxidative plasma species on polymers and advance the understanding of plasma-polymer interactions on a molecular scale.

Iron plaque formation and morphoanatomy of roots from species of restinga subjected to excess iron.

PubMed

Siqueira-Silva, Advanio Inácio; da Silva, Luzimar Campos; Azevedo, Aristéa Alves; Oliva, Marco Antonio

2012-04-01

The restingas, a sandy coastal plain ecosystem of Brazil, have received an additional amount of iron due to the activity of mining industries. The present study aims to characterize morphoanatomically and histochemically the iron plaque formation on roots of Ipomoea pes-caprae L. and Canavalia rosea DC, cultivated in hydroponic solution with and without excess iron. The iron plaque formation as well as changes in the external morphology of the lateral roots of both species were observed after the subjection to excess iron. Changes in the nutrient uptake, and in the organization and form of the pericycle and cortex cells were observed for both species. Scanning electron microscopy showed evident iron plaques on the whole surface of the root. The iron was histolocalized in all root tissues of both species. The species of restinga studied here formed iron plaque in their roots when exposed to excess of this element, which may compromise their development in environments polluted by particulated iron. Copyright © 2011 Elsevier Inc. All rights reserved.

Update on the taxonomy and the clinical and laboratory characteristics of pigmented anaerobic gram-negative rods.

PubMed

Jousimies-Somer, H R

1995-06-01

Pigmented anaerobic gram-negative rods are currently categorized as 17 species distributed in three genera: Prevotella, Porphyromonas, and Bacteroides. These organisms are often encountered in clinical specimens but are also found as part of the indigenous flora on various mucosal surfaces. Several studies are presently assessing the association of individual species with health and disease. For example, Porphyromonas gingivalis and Porphyromonas endodontalis are key putative pathogens in adult periodontitis and root canal infections, respectively. Porphyromonas asaccharolytica is prevalent in extraoral infections. The Porphyromonas species of animal origin have been isolated from infected bite wounds in humans. Isolates closely resembling Bacteroides levii have been recovered from various types of human infections. According to preliminary reports, Prevotella intermedia tends to be associated more often with periodontal disease than with a healthy oral cavity. In the laboratory, enzyme profiling facilitates the identification of these pigmented rods. Beta-Lactamase production is more common among prevotella species (30%-50%) than among Porphyromonas species (< 10%).

Morphological and molecular identification of two new Ganoderma species on Casuarina equisetifolia from China.

PubMed

Xing, Jia-Hui; Sun, Yi-Fei; Han, Yu-Li; Cui, Bao-Kai; Dai, Yu-Cheng

2018-01-01

Ganoderma is a cosmopolitan white rot fungal genus, famous for its medicinal properties. In the present study, two new Ganoderma species were collected from south-eastern China and described on the basis of morphological characters and phylogenetic analyses of sequences of the internal transcribed spacer (ITS) region, the translation elongation factor 1-α gene (EF1-α) and the second subunit of RNA polymerase II (RPB2). Specimens of both species were found on living trees of Casuarina equisetifolia . Ganoderma angustisporum sp. nov. is characterised by its sessile basidiomata and almond-shaped, slightly truncate, narrow basidiospores (9-11.3 × 4-5.2 µm). Ganoderma casuarinicola sp. nov. is characterised by its strongly laccate reddish-brown pileal surface, luminous yellow to yellowish-brown cutis and ellipsoid, truncate basidiospores (9-10.2 × 5-6 µm). The two new species are compared with their related taxa. Phylogenetic analyses confirmed that G. angustisporum and G. casuarinicola are distinct species within Ganoderma .

Point defects at the ice (0001) surface

PubMed Central

Watkins, Matthew; VandeVondele, Joost; Slater, Ben

2010-01-01

Using density functional theory we investigate whether intrinsic defects in ice surface segregate. We predict that hydronium, hydroxide, and the Bjerrum L- and D-defects are all more stable at the surface. However, the energetic cost to create a D-defect at the surface and migrate it into the bulk crystal is smaller than its bulk formation energy. Absolute and relative segregation energies are sensitive to the surface structure of ice, especially the spatial distribution of protons associated with dangling hydrogen bonds. It is found that the basal plane surface of hexagonal ice increases the bulk concentration of Bjerrum defects, strongly favoring D-defects over L-defects. Dangling protons associated with undercoordinated water molecules are preferentially injected into the crystal bulk as Bjerrum D-defects, leading to a surface dipole that attracts hydronium ions. Aside from the disparity in segregation energies for the Bjerrum defects, we find the interactions between defect species to be very finely balanced; surface segregation energies for hydronium and hydroxide species and trapping energies of these ionic species with Bjerrum defects are equal within the accuracy of our calculations. The mobility of the ionic hydronium and hydroxide species is greatly reduced at the surface in comparison to the bulk due to surface sites with high trapping affinities. We suggest that, in pure ice samples, the surface of ice will have an acidic character due to the presence of hydronium ions. This may be important in understanding the reactivity of ice particulates in the upper atmosphere and at the boundary layer. PMID:20615938

Foundations of Wind Turbines as Stepping Stones for Non-Indigenous Species in the Southern North Sea

NASA Astrophysics Data System (ADS)

De Mesel, I.; Degraer, S.; Kerckhof, F.; Schön, I.; Martens, K.

2016-02-01

Since 2008, offshore wind farms have been constructed in the shallow waters (<50m) of the Southern North Sea. At present, hundreds of turbines are operational and many more are planned. A new habitat for benthos has been created, with vertical hard structures in the offshore environment, extending from the sandy seabed to the sea surface. Monitoring in Belgian waters focussed on the succession of the fouling community in the sub- and intertidal zone, with special attention to non-indigenous species (NIS). A Metridium senile-Jassa herdmani dominated community developed in the subtidal, and only few NIS were present (3 out of a total of 90 species observed). Their presence was however most striking in the intertidal zone, where we identified 17 obligate intertidal species with about half of them being non-indigenous. This study confirmed the hypothesis that the introduced hard substrata within offshore wind farms play an important role in the establishment and the expansion of the population of both indigenous and non-indigenous species. Foundations of wind turbines strengthen the strategic position of NIS in the southern North Sea. An ongoing study on the population genetics of a fouling species (Patella vulgata) will, in combination with dispersal modelling, elucidate the dispersal pattern and connectivity with neighbouring areas, and the role of the foundations as stepping stones.

Quantification of Methylated Selenium, Sulfur, and Arsenic in the Environment

PubMed Central

Vriens, Bas; Ammann, Adrian A.; Hagendorfer, Harald; Lenz, Markus; Berg, Michael; Winkel, Lenny H. E.

2014-01-01

Biomethylation and volatilization of trace elements may contribute to their redistribution in the environment. However, quantification of volatile, methylated species in the environment is complicated by a lack of straightforward and field-deployable air sampling methods that preserve element speciation. This paper presents a robust and versatile gas trapping method for the simultaneous preconcentration of volatile selenium (Se), sulfur (S), and arsenic (As) species. Using HPLC-HR-ICP-MS and ESI-MS/MS analyses, we demonstrate that volatile Se and S species efficiently transform into specific non-volatile compounds during trapping, which enables the deduction of the original gaseous speciation. With minor adaptations, the presented HPLC-HR-ICP-MS method also allows for the quantification of 13 non-volatile methylated species and oxyanions of Se, S, and As in natural waters. Application of these methods in a peatland indicated that, at the selected sites, fluxes varied between 190–210 ng Se·m−2·d−1, 90–270 ng As·m−2·d−1, and 4–14 µg S·m−2·d−1, and contained at least 70% methylated Se and S species. In the surface water, methylated species were particularly abundant for As (>50% of total As). Our results indicate that methylation plays a significant role in the biogeochemical cycles of these elements. PMID:25047128

Characterisation of the gill mucosal bacterial communities of four butterflyfish species: a reservoir of bacterial diversity in coral reef ecosystems.

PubMed

Reverter, Miriam; Sasal, Pierre; Tapissier-Bontemps, N; Lecchini, D; Suzuki, M

2017-06-01

While recent studies have suggested that fish mucus microbiota play an important role in homeostasis and prevention of infections, very few studies have investigated the bacterial communities of gill mucus. We characterised the gill mucus bacterial communities of four butterflyfish species and although the bacterial diversity of gill mucus varied significantly between species, Shannon diversities were high (H = 3.7-5.7) in all species. Microbiota composition differed between butterflyfishes, with Chaetodon lunulatus and C. ornatissimus having the most similar bacterial communities, which differed significantly from C. vagabundus and C. reticulatus. The core bacterial community of all species consisted of mainly Proteobacteria followed by Actinobacteria and Firmicutes. Chaetodonlunulatus and C. ornatissimus bacterial communities were mostly dominated by Gammaproteobacteria with Vibrio as the most abundant genus. Chaetodonvagabundus and C. reticulatus presented similar abundances of Gammaproteobacteria and Alphaproteobacteria, which were well represented by Acinetobacter and Paracoccus, respectively. In conclusion, our results indicate that different fish species present specific bacterial assemblages. Finally, as mucus layers are nutrient hotspots for heterotrophic bacteria living in oligotrophic environments, such as coral reef waters, the high bacterial diversity found in butterflyfish gill mucus might indicate external fish mucus surfaces act as a reservoir of coral reef bacterial diversity. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Complex chemical composition of colored surface films formed from reactions of propanal in sulfuric acid at upper troposphere/lower stratosphere aerosol acidities.

PubMed

Van Wyngarden, A L; Pérez-Montaño, S; Bui, J V H; Li, E S W; Nelson, T E; Ha, K T; Leong, L; Iraci, L T

Particles in the upper troposphere and lower stratosphere (UT/LS) consist mostly of concentrated sulfuric acid (40-80 wt %) in water. However, airborne measurements have shown that these particles also contain a significant fraction of organic compounds of unknown chemical composition. Acid-catalyzed reactions of carbonyl species are believed to be responsible for significant transfer of gas phase organic species into tropospheric aerosols and are potentially more important at the high acidities characteristic of UT/LS particles. In this study, experiments combining sulfuric acid (H 2 SO 4 ) with propanal and with mixtures of propanal with glyoxal and/or methylglyoxal at acidities typical of UT/LS aerosols produced highly colored surface films (and solutions) that may have implications for aerosol properties. In order to identify the chemical processes responsible for the formation of the surface films, attenuated total reflectance-Fourier transform infrared (ATR-FTIR) and 1 H nuclear magnetic resonance (NMR) spectroscopies were used to analyze the chemical composition of the films. Films formed from propanal were a complex mixture of aldol condensation products, acetals and propanal itself. The major aldol condensation products were the dimer (2-methyl-2-pentenal) and 1,3,5-trimethylbenzene that was formed by cyclization of the linear aldol condensation trimer. Additionally, the strong visible absorption of the films indicates that higher-order aldol condensation products must also be present as minor species. The major acetal species were 2,4,6-triethyl-1,3,5-trioxane and longer-chain linear polyacetals which are likely to separate from the aqueous phase. Films formed on mixtures of propanal with glyoxal and/or methylglyoxal also showed evidence of products of cross-reactions. Since cross-reactions would be more likely than self-reactions under atmospheric conditions, similar reactions of aldehydes like propanal with common aerosol organic species like glyoxal and methylglyoxal have the potential to produce significant organic aerosol mass and therefore could potentially impact chemical, optical and/or cloud-forming properties of aerosols, especially if the products partition to the aerosol surface.

Complex chemical composition of colored surface films formed from reactions of propanal in sulfuric acid at upper troposphere/lower stratosphere aerosol acidities

PubMed Central

Van Wyngarden, A. L.; Pérez-Montaño, S.; Bui, J. V. H.; Li, E. S. W.; Nelson, T. E.; Ha, K. T.; Leong, L.; Iraci, L. T.

2016-01-01

Particles in the upper troposphere and lower stratosphere (UT/LS) consist mostly of concentrated sulfuric acid (40–80 wt %) in water. However, airborne measurements have shown that these particles also contain a significant fraction of organic compounds of unknown chemical composition. Acid-catalyzed reactions of carbonyl species are believed to be responsible for significant transfer of gas phase organic species into tropospheric aerosols and are potentially more important at the high acidities characteristic of UT/LS particles. In this study, experiments combining sulfuric acid (H2SO4) with propanal and with mixtures of propanal with glyoxal and/or methylglyoxal at acidities typical of UT/LS aerosols produced highly colored surface films (and solutions) that may have implications for aerosol properties. In order to identify the chemical processes responsible for the formation of the surface films, attenuated total reflectance–Fourier transform infrared (ATR-FTIR) and 1H nuclear magnetic resonance (NMR) spectroscopies were used to analyze the chemical composition of the films. Films formed from propanal were a complex mixture of aldol condensation products, acetals and propanal itself. The major aldol condensation products were the dimer (2-methyl-2-pentenal) and 1,3,5-trimethylbenzene that was formed by cyclization of the linear aldol condensation trimer. Additionally, the strong visible absorption of the films indicates that higher-order aldol condensation products must also be present as minor species. The major acetal species were 2,4,6-triethyl-1,3,5-trioxane and longer-chain linear polyacetals which are likely to separate from the aqueous phase. Films formed on mixtures of propanal with glyoxal and/or methylglyoxal also showed evidence of products of cross-reactions. Since cross-reactions would be more likely than self-reactions under atmospheric conditions, similar reactions of aldehydes like propanal with common aerosol organic species like glyoxal and methylglyoxal have the potential to produce significant organic aerosol mass and therefore could potentially impact chemical, optical and/or cloud-forming properties of aerosols, especially if the products partition to the aerosol surface. PMID:27212937

Description of a new leech species of Helobdella (Clitellata: Glossiphoniidae) from Mexico with a review of Mexican congeners and a taxonomic key.

PubMed

Salas-Montiel, Ricardo; Phillips, Anna J; De Leon, Gerardo Perez-Ponce; Oceguera-Figueroa, Alejandro

2014-12-19

To date, six species of the leech genus Helobdella have been recorded from Mexico: Helobdella atli, Helobdella elongata, Helobdella octatestisaca, Helobdella socimulcensis, Helobdella virginiae and Helobdella temiscoensis n. sp. This new species is characterized by a lanceolate body, the presence of a nuchal scute, uniform brown pigment on both dorsal and ventral surfaces, the absence of papillae, well-separated eyespots, six pairs of testisacs and five pairs of crop caeca, the last of which forms posterior caeca. In addition, we provide new geographic records for Helobdella species from Mexico resulting from our own collections, vouchers deposited at the Colección Nacional de Helmintos from the Instituto de Biología, UNAM, Mexico and vouchers at the Invertebrate Zoology Collection of the Smithsonian's National Museum of Natural History (USNM) Washington D.C., USA. We present a comprehensive review of Mexican Helobdella species, including the new species, with notes on the characteristic morphology and geographic distribution of each species with 91 new records from 20 states. In addition, we provide a taxonomic key for the identification of the Mexican species.

Effect of a long-term fire retardant (Fire Trol 934) on the germination of nine Mediterranean-type shrub species.

PubMed

Cruz, Alberto; Serrano, Marián; Navarro, Esther; Luna, Belén; Moreno, José M

2005-12-01

Fire Trol 934 is a long-term fire retardant commonly used in fire prevention and extinction. Our objective was to determine the effect of this chemical on seed germination of nine plant species from Mediterranean-type shrublands, where these chemicals are potentially used. Seeds were exposed to five different Fire Trol concentrations, (0 (control) to 10%, on a log scale) and monitored in a germination chamber for nine weeks. Seeds from four Cistus species were subjected to an additional heat treatment that simulated thermal scarification caused by fire. Retardant exposure caused a significant decrease in total germination in all species, and exposure to the highest Fire Trol concentration (10%) resulted in complete inhibition of germination. However, the sensitivity to Fire Trol varied across species and this differential species sensitivity may potentially lead to different impacts in the soil seed banks depending on whether sites are burned or unburned. Exposure to Fire Trol 934 may affect recruitment of shrubland species particularly during dry autumns, due to limited leaching of these chemicals from the soil surface. Consequently, its use should be avoided in sites where particularly sensitive plant species are present. Copyright (c) 2005 Wiley Periodicals, Inc.

A new species of Leptolalax (Anura: Megophryidae) from the highest mountain in Indochina.

PubMed

Rowley, Jodi J L; Dau, Vinh Quang; Nguyen, Tao Thien

2013-11-21

We describe a new species of Leptolalax from northern Vietnam. Leptolalax botsfordi sp. nov. is distinguished from its congeners by a combination of (1) supra-axillary and ventrolateral glands present; (2) dark brownish red ventral surface with white speckling; (3) medium body size for the genus (29.1-32.6 mm in 7 adult males, 30.0-31.8 mm in 2 females); (4) black markings on the flanks absent; (5) toes with rudimentary webbing and weak lateral fringing; (6) large pectoral glands (1.1-1.9 mm; 4-6% SVL) and femoral glands (2.4-4.3 mm; 7-14% SVL); and (7) an advertisement call with a dominant frequency of 2.6-3.2 kHz (at 14.0º C). At present, the new species is known only from upper montane forest between 2,795-2,815 m elevation on Mount Fansipan, Hoang Lien National Park. To our knowledge, Leptolalax botsfordi sp. nov. occurs at higher elevations than any other species in the genus. If L. botsfordi sp. nov. is truly restricted to a narrow, high-elevation band, it is likely to be particularly vulnerable to the effects of climate change. The new species also faces the immediate threat of habitat degradation and pollution due to tourist activity.

The factors controlling species density in herbaceous plant communities: An assessment

USGS Publications Warehouse

Grace, J.B.

1999-01-01

This paper evaluates both the ideas and empirical evidence pertaining to the control of species density in herbaceous plant communities. While most theoretical discussions of species density have emphasized the importance of habitat productivity and disturbance regimes, many other factors (e.g. species pools, plant litter accumulation, plant morphology) have been proposed to be important. A review of literature presenting observations on the density of species in small plots (in the vicinity of a few square meters or less), as well as experimental studies, suggests several generalizations: (1) Available data are consistent with an underlying unimodal relationship between species density and total community biomass. While variance in species density is often poorly explained by predictor variables, there is strong evidence that high levels of community biomass are antagonistic to high species density. (2) Community biomass is just one of several factors affecting variations in species density. Multivariate analyses typically explain more than twice as much variance in species density as can be explained by community biomass alone. (3) Disturbance has important and sometimes complex effects on species density. In general, the evidence is consistent with the intermediate disturbance hypothesis but exceptions exist and effects can be complex. (4) Gradients in the species pool can have important influences on patterns of species density. Evidence is mounting that a considerable amount of the observed variability in species density within a landscape or region may result from environmental effects on the species pool. (5) Several additional factors deserve greater consideration, including time lags, species composition, plant morphology, plant density and soil microbial effects. Based on the available evidence, a conceptual model of the primary factors controlling species density is presented here. This model suggests that species density is controlled by the effects of disturbance, total community biomass, colonization, the species pool and spatial heterogeneity. The structure of the model leads to two main expectations: (1) while community biomass is important, multivariate approaches will be required to understand patterns of variation in species density, and (2) species density will be more highly correlated with light penetration to the soil surface, than with above-ground biomass, and even less well correlated with plant growth rates (productivity) or habitat fertility. At present, data are insufficient to evaluate the relative importance of the processes controlling species density. Much more work is needed if we are to adequately predict the effects of environmental changes on plant communities and species diversity.

Classification of CITES-listed and other neotropical Meliaceae wood images using convolutional neural networks.

PubMed

Ravindran, Prabu; Costa, Adriana; Soares, Richard; Wiedenhoeft, Alex C

2018-01-01

The current state-of-the-art for field wood identification to combat illegal logging relies on experienced practitioners using hand lenses, specialized identification keys, atlases of woods, and field manuals. Accumulation of this expertise is time-consuming and access to training is relatively rare compared to the international demand for field wood identification. A reliable, consistent and cost effective field screening method is necessary for effective global scale enforcement of international treaties such as the Convention on the International Trade in Endagered Species (CITES) or national laws (e.g. the US Lacey Act) governing timber trade and imports. We present highly effective computer vision classification models, based on deep convolutional neural networks, trained via transfer learning, to identify the woods of 10 neotropical species in the family Meliaceae, including CITES-listed Swietenia macrophylla , Swietenia mahagoni , Cedrela fissilis , and Cedrela odorata . We build and evaluate models to classify the 10 woods at the species and genus levels, with image-level model accuracy ranging from 87.4 to 97.5%, with the strongest performance by the genus-level model. Misclassified images are attributed to classes consistent with traditional wood anatomical results, and our species-level accuracy greatly exceeds the resolution of traditional wood identification. The end-to-end trained image classifiers that we present discriminate the woods based on digital images of the transverse surface of solid wood blocks, which are surfaces and images that can be prepared and captured in the field. Hence this work represents a strong proof-of-concept for using computer vision and convolutional neural networks to develop practical models for field screening timber and wood products to combat illegal logging.

Elk Hills Endangered Species Program: environmental assessment of the blunt-nosed leopard lizard, Crotaphytus silus. Phase 2, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mullen, R.K.

1981-02-01

This report represents an extension of previous findings concerning the status of the endangered species, Crotaphytus silus (blunt-nosed leopard lizard) on the Naval Petroleum Reserve Number 1 (NPR-1), Elk Hills, California. Previous findings in 1979 were limited to superficial observations of the occurrence and distribution of C. silus on NPR-1. The present report details findings from more extensive field work conducted from late May to early August 1980, and complements the 1979 work. The ultimate purpose of the investigations reported here is to provide sufficient bases for making informed decisions concerning the relationships of present and possible future oil-related activitiesmore » at Elk Hills to the status of C. silus. There have been no particularly unique life history indicators of environmental impact on C. silus mediated through activities on NPR-1. Observations may be made, however, on the seasonal correlates of such activities: (1) individual C. silus may be buried or fatally exposed to the environment by construction activities occurring during the species' hibernation; (2) during periods when adult C. silus is active on the surface, construction activities may displace individuals that may not then be able to successfully occupy a new range, although it is to be noted in this regard that the home range of the species can be rather plastic; (3) construction activities bury or expose nest chambers of C. silus. This would unfavorably affect an average of three potential hatchlings with each burial or exposure; and (4) construction occurring when only (or predominantly) hatchlings are active on the surface may affect animals less able to avoid these activities than adults. In addition, hibernating adults will be affected, as previously noted.« less

Theme and variations: amphibious air-breathing intertidal fishes.

PubMed

Martin, K L

2014-03-01

Over 70 species of intertidal fishes from 12 families breathe air while emerging from water. Amphibious intertidal fishes generally have no specialized air-breathing organ but rely on vascularized mucosae and cutaneous surfaces in air to exchange both oxygen and carbon dioxide. They differ from air-breathing freshwater fishes in morphology, physiology, ecology and behaviour. Air breathing and terrestrial activity are present to varying degrees in intertidal fish species, correlated with the tidal height of their habitat. The gradient of amphibious lifestyle includes passive remainers that stay in the intertidal zone as tides ebb, active emergers that deliberately leave water in response to poor aquatic conditions and highly mobile amphibious skipper fishes that may spend more time out of water than in it. Normal terrestrial activity is usually aerobic and metabolic rates in air and water are similar. Anaerobic metabolism may be employed during forced exercise or when exposed to aquatic hypoxia. Adaptations for amphibious life include reductions in gill surface area, increased reliance on the skin for respiration and ion exchange, high affinity of haemoglobin for oxygen and adjustments to ventilation and metabolism while in air. Intertidal fishes remain close to water and do not travel far terrestrially, and are unlikely to migrate or colonize new habitats at present, although in the past this may have happened. Many fish species spawn in the intertidal zone, including some that do not breathe air, as eggs and embryos that develop in the intertidal zone benefit from tidal air emergence. With air breathing, amphibious intertidal fishes survive in a variable habitat with minimal adjustments to existing structures. Closely related species in different microhabitats provide unique opportunities for comparative studies. © 2013 The Fisheries Society of the British Isles.

Leaf structural traits of tropical woody species resistant to cement dust.

PubMed

Siqueira-Silva, Advanio Inácio; Pereira, Eduardo Gusmão; Modolo, Luzia Valentina; Paiva, Elder Antonio Sousa

2016-08-01

Cement industries located nearby limestone outcrops in Brazil have contributed to the coating of cement dust over native plant species. However, little is known about the extent of the response of tropical woody plants to such environmental pollutant particularly during the first stages of plant development and establishment. This work focused on the investigation of possible alterations in leaf structural and ultrastructural traits of 5-month-old Guazuma ulmifolia Lam. (Malvaceae), 6-month-old Myracrodruon urundeuva Allemão (Anacardiaceae), and 9-month-old Trichilia hirta L. (Meliaceae) challenged superficially with cement dust during new leaf development. Leaf surface of plants, the soil or both (leaf plus soil), were treated (or not) for 60 days, under controlled conditions, with cement dust at 2.5 or 5.0 mg cm(-2). After exposure, no significant structural changes were observed in plant leaves. Also, no plant death was recorded by the end of the experiment. There was also some evidence of localized leaf necrosis in G. ulmifolia and T. hirta, leaf curling in M. urundeuva and T. hirta, and bulges formation on epidermal surface of T. hirta, after cement dust contact with plant shoots. All species studied exhibited stomata obliteration while T. hirta, in particular, presented early leaf abscission, changes in cellular relief, and organization and content of midrib cells. No significant ultrastructural alterations were detected under the experimental conditions studied. Indeed, mesophyll cells presented plastids with intact membrane systems. The high plant survival rates, together with mild morphoanatomic traits alterations in leaves, indicate that G. ulmifolia is more resistant to cement dust pollutant, followed by M. urundeuva and T. hirta. Thus, the three plant species are promising for being used to revegetate areas impacted by cement industries activities.

Revision of Gangesia (Cestoda: Proteocephalidea) in the Indomalayan Region: Morphology, Molecules and Surface Ultrastructure

PubMed Central

Ash, Anirban; Scholz, Tomáš; de Chambrier, Alain; Brabec, Jan; Oros, Mikuláš; Kar, Pradip Kumar; Chavan, Shivaji Prabhakar; Mariaux, Jean

2012-01-01

Tapeworms of Gangesia Woodland, 1924 (Cestoda: Proteocephalidea) parasitic in freshwater fishes in the Indomalayan Region were critically reviewed. Evaluation of type specimens and newly collected materials from Bangladesh, Cambodia and India, as well as critical examination of extensive literature have shown that only the following four species, instead of 48 nominal species of Gangesia and Silurotaenia Nybelin, 1942 reported from this region (36 new synonymies proposed), are valid: Gangesia bengalensis (Southwell, 1913), type-species of the genus and most common parasite of Wallago attu (Siluridae), G. macrones Woodland, 1924 typical of Sperata seenghala (Bagridae), both species characterized by the possession of two circles of hooks on the rostellum-like organ and several rows of hooklets on the anterior margins of suckers; G. agraensis Verma, 1928 from W. attu (typical host), which has the scolex with only one circle of hooks and 1–3 incomplete rows of tiny hooklets on the suckers; and G. vachai (Gupta and Parmar, 1988) n. comb. from several catfishes, which possesses 4–6 circles of hooks and 5–11 rows of hooklets on the anterior half of suckers. Scolex morphology, including surface ultrastructure (microtriches), of all but one species (G. vachai) is described for the first time using scanning electron microscopy. A phylogenetic analysis based on the partial sequences encoding the large nuclear ribosomal subunit RNA gene has shown that three Indomalayan species, namely G. bengalensis, G. macrones and G. vachai, form a monophyletic group within Gangesia, whereas G. agraensis tends to form a clade with the Palaearctic species of the genus. A table with differential characters of all species from the Indomalayan Region is also provided together with a key to identification of genera of the subfamily Gangesiinae. The present study demonstrates that species of Silurotaenia do not occur in the Indomalayan region. PMID:23056306

Early interactions between leukocytes and three different potentially bioactive titanium surface modifications.

PubMed

Arvidsson, Anna; Malmberg, Per; Kjellin, Per; Currie, Fredrik; Arvidsson, Martin; Franke Stenport, Victoria

2011-05-01

The aim of the present study was to compare the early interactions between leukocytes and three different surface modifications, suggested as bioactive. Blasted titanium discs were modified by alkali and heat treatment, sodium fluoride treatment, or hydroxyapatite coating. A number of these discs were also immersed in simulated body fluid (SBF) for a week, a treatment which yielded high levels of calcium and phosphate on each surface type. The specimens were exposed for human venous blood for 32 minutes and the respiratory burst response was measured in terms of reactive oxygen species with a luminometer, and coverage of viable cells with a fluorescence microscope after staining steps. The topography, morphology, and chemistry of the surfaces were evaluated with optical interferometry and scanning electron microscopy/energy dispersive X-ray analysis (SEM/EDX). A high respiratory burst response was found for HA coated titanium in comparison with the other surface groups (p < 0.0005). The SBF immersion resulted in an increased respiratory burst response (p < 0.0005) and removed statistically significant differences between the surface groups. Thus, the results in the present study indicate that different titanium surface modifications influence the early inflammatory response differently, and that calcium phosphate compounds increase the inflammatory response. Copyright © 2011 Wiley Periodicals, Inc.

Symposium on surface coal mining and reclamation in the Northern Great Plains. Research on shrub establishment in reclamation of surface-mined lands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eddleman, L.E.

1980-01-01

Shrubs are an important component of plant communities in southeastern Montana. Re-establishment of the majority of native shrubs by seed on surface coal mine lands has not been generally successful. Field plantings at the Rosebud Mine of 25 shrub and half-shrub species were initiated in 1978 using seed from native populations. Three species Atriplex canescens, Atriplex nuttallii and Ceratoids lanata establish numerous seedlings in both wet and dry years. No emergence was obtained from 12 species.

Comparative studies of biological activity of cadmium-based quantum dots with different surface modifications

NASA Astrophysics Data System (ADS)

Kalinowska, D.; Grabowska-Jadach, I.; Drozd, M.; Pietrzak, M.

2018-05-01

This paper presents a modification of the surface of CdS/ZnS and CdSe x S1-x /ZnS quantum dots (QDs) with 3-mercaptopropionic and 6-mercaptohexanoic acid. The obtained QDs were characterized using TEM, DLS, UV-Vis, and fluorescence spectroscopy. Flow cytometry was applied to evaluate the cytotoxicity of QDs and examine the type of death caused by the tested nanoparticles. In addition, the generation of reactive oxygen species after incubation of the tested cells with CdSe x S1-x /ZnS-MPA and CdSe x S1-x /ZnS-MHA QDs was evaluated. The study was conducted on three cell lines: adherent (A549 and MRC-5) and suspension ones (K562). The conducted research demonstrated that the tested nanoparticles exhibit concentration-dependent toxicity. It was observed that the surface modification influences the toxicity level of the examined QDs, and modification of their surface with the use of the ligand of longer carbon chain (MHA) reduces the toxicity in comparison with QDs-MPA. It was also found that all tested QDs caused the death of cells in the course of necrosis. Based on obtained results, it was concluded that the cytotoxicity of QDs is to a large extent related to reactive oxygen species (ROS) generation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nahum, T.; Dodiuk, H.; Dotan, A.

Superhydrophobic surfaces with contact angle (CA) >150 and sliding angle (SA) <10 have been aroused curiosity over the years due to their various applications. Superhydrophobicity can be obtained tailoring the chemistry and the roughness of the surface, mimicking the Lotus flower. Most superhydrophobic surfaces based on secondary bonding lose their roughness in harsh conditions and are unsuitable for practical applications. Photoreactive SiO{sub 2} nanoparticles (NPs) based on benzophenone (BP) can be a very effective tool for formation of reactive species that function as a molecular bridge by covalent bonding between the NP and any polymer matrix with C-C and C-Hmore » bonds. The present work focused on thermoset radiation curing urethane acrylate. Upon UV irradiation reactive excited nπ* triplet benzophenone species are formed and react through hydrogen abstraction to form ketyl radicals which interact with a radicals from the UV irradiated polymer matrix to yield covalent bonding. Roughness was achieved by dipping the substrate in SiO{sub 2}@BPs NPs dispersion followed by irradiation. Fluoroalkylsilane was used to obtain hydrophobic top layer. AFM nano manipulation was used to verify the immobilization of NPs. Evaluation of durability was made using air flow at 300 km/hr. Preliminary results indicate the formation of super hydrophobic surfaces (CA>150 and SA<10) with improved stability.« less

Body mass modulates huddling dynamics and body temperature profiles in rabbit pups.

PubMed

Bautista, Amando; Zepeda, José Alfredo; Reyes-Meza, Verónica; Féron, Christophe; Rödel, Heiko G; Hudson, Robyn

2017-10-01

Altricial mammals typically lack the physiological capacity to thermoregulate independently during the early postnatal period, and in litter-bearing species the young benefit strongly from huddling together with their litter siblings. Such litter huddles are highly dynamic systems, often characterized by competition for energetically favorable, central positions. In the present study, carried out in domestic rabbits Oryctolagus cuniculus, we asked whether individual differences in body mass affect changes in body temperature during changes in the position within the huddle. We predicted that pups with relatively lower body mass should be more affected by such changes arising from huddle dynamics in comparison to heavier ones. Changes in pups' maximum body surface temperature (determined by infrared thermography) were significantly affected by changes in the number of their neighbors in the litter huddle, and indeed these temperature changes largely depended on the pups' body mass relative to their litter siblings. Lighter pups showed significant increases in their maximum body surface temperature when their number of huddling partners increased by one or two siblings whereas pups with intermediate or heavier body mass did not show such significant increases in maximum body temperature when experiencing such changes. A similar pattern was found with respect to average body surface temperature. This strong link between changes in the number of huddling partners and body surface temperature in lighter pups might, on the one hand, arise from a higher vulnerability of such pups due to their less favorable body surface area-to-volume ratio. On the other hand, as lighter pups generally had fewer neighbors than heavier ones and thus typically a comparatively smaller body surface in contact with siblings, they potentially had more to gain from increasing their number of neighbors. The present findings might help to understand how individual differences in body mass within a litter lead to the emergence of individual differences in sibling interactions during early postnatal life in different species of altricial and litter-bearing mammals. Copyright © 2017 Elsevier Inc. All rights reserved.

Method of making maximally dispersed heterogeneous catalysts

DOEpatents

Jennison, Dwight R [Albuquerque, NM

2005-11-15

A method of making a catalyst with monolayer or sub-monolayer metal by controlling the wetting characteristics on the support surface and increasing the adhesion between the catalytic metal and an oxide layer. There are two methods that have been demonstrated by experiment and supported by theory. In the first method, which is useful for noble metals as well as others, a negatively-charged species is introduced to the surface of a support in sub-ML coverage. The layer-by-layer growth of metal deposited onto the oxide surface is promoted because the adhesion strength of the metal-oxide interface is increased. This method can also be used to achieve nanoislands of metal upon sub-ML deposition. The negatively-charged species can either be deposited onto the oxide surface or a compound can be deposited that dissociates on, or reacts with, the surface to form the negatively-charged species. The deposited metal adatoms can thereby bond laterally to the negatively-charged species as well as vertically to the oxide surface. Thus the negatively-charged species serve as anchors for the metal. In the second method, a chemical reaction that occurs when most metals are deposited on a fully hydroxylated oxide surface is used to create cationic metal species that bind strongly both to the substrate and to metallic metal atoms. These are incorporated into the top layer of the substrate and bind strongly both to the substrate and to metallic metal atoms. In this case, these oxidized metal atoms serve as the anchors. Here, as in the previous method, nanoislands of catalytic metal can be achieved to increase catalytic activity, or monolayers or bilayers of reactive metal can also be made.

A transmission and scanning electron microscopic study of the saccule in five species of catfishes.

PubMed

Jenkins, D B

1979-01-01

The sacculi of five species of catfishes were studied by transmission and scanning electron microscopy. In four species, the sagitta exhibited a multifluted anterior part and a tapered posterior part; in Corydoras aeneus, however, the fluted part was absent, and a vertical component extended dorsally to terminate near the opening of the transverse canal. In all species, the otoliths had a laminar structure. An otolithic membrane was present, and hair cell bundles projected into cavities on the macular surface of the membrane. Attachments of the otolithic membrane to the neuroepithelium included short extensions of the membrane to the tallest components of the hair cell bundles of the peripheral cells and more delicate connections to the kinocilium and taller stereocilia of central cells; in addition, attachments to the microvilli of supporting cells were present. In both hair cells and supporting cells single microtubules and bundles of microtubules were present; the bundles had an orderly arrangement and were associated with cytoplasmic densities surrounding the desmosomes. The hair cells were innervated by both afferent and efferent nerve endings. Studies of the polarization of the hair cells in all species (except C. aeneus) showed that there was a single longitudinal axis that divided dorsally polarized cells from those oriented ventrally. In Doras spinosissimus and Bunocephalus bicolor, an additional line of polarization was evident in a small area in the anterior part of the macula; therefore, in these forms there was a double bipolar orientation.

Isolation, screening, and characterization of surface-active agent-producing, oil-degrading marine bacteria of Mumbai Harbor.

PubMed

Mohanram, Rajamani; Jagtap, Chandrakant; Kumar, Pradeep

2016-04-15

Diverse marine bacterial species predominantly found in oil-polluted seawater produce diverse surface-active agents. Surface-active agents produced by bacteria are classified into two groups based on their molecular weights, namely biosurfactants and bioemulsifiers. In this study, surface-active agent-producing, oil-degrading marine bacteria were isolated using a modified Bushnell-Haas medium with high-speed diesel as a carbon source from three oil-polluted sites of Mumbai Harbor. Surface-active agent-producing bacterial strains were screened using nine widely used methods. The nineteen bacterial strains showed positive results for more than four surface-active agent screening methods; further, these strains were characterized using biochemical and nucleic acid sequencing methods. Based on the results, the organisms belonged to the genera Acinetobacter, Alcanivorax, Bacillus, Comamonas, Chryseomicrobium, Halomonas, Marinobacter, Nesterenkonia, Pseudomonas, and Serratia. The present study confirmed the prevalence of surface-active agent-producing bacteria in the oil-polluted waters of Mumbai Harbor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study of reticulated vitreous carbon surface treated by plasma immersion ion implantation for electrodes production

NASA Astrophysics Data System (ADS)

Silva, L. L. G.; Conceição, D. A. S.; Oishi, S. S.; Toth, A.; Ueda, M.

2012-03-01

RVC samples were treated by nitrogen plasma immersion ion implantation (N-PIII) for electrodes production. High-voltage pulses with amplitudes of -3.0 kV or -10.0 kV were applied to the RVC samples while the treatment time was 10, 20 and 30 min. The samples were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and electrochemical measurements. The SEM images present an apparent enhancement of the surface roughness after the treatment probably due to the surface sputtering during the PIII process. This observation is in agreement with the specific electrochemical surface area (SESA) of RVC electrodes. An increase was observed of the SESA values for the PIII-treated samples compared to the untreated specimen. Some oxygen and nitrogen containing groups were introduced on the RVC surface after the PIII treatment. Both plasma-induced process: the surface roughening and the introduction of the polar species on the RVC surface are beneficial for the RVC electrodes application.

Atomic and molecular adsorption on Fe(110)

DOE PAGES

Xu, Lang; Kirvassilis, Demetrios; Bai, Yunhai; ...

2017-09-12

Iron is the principal catalyst for the ammonia synthesis process and the Fischer–Tropsch process, as well as many other heterogeneously catalyzed reactions. It is thus of fundamental importance to understand the interactions between the iron surface and various reaction intermediates. Here in this paper, we present a systematic study of atomic and molecular adsorption behavior over Fe(110) using periodic, self-consistent density functional theory (DFT-GGA) calculations. The preferred binding sites, binding energies, and the corresponding surface deformation energies of five atomic species (H, C, N, O, and S), six molecular species (NH 3, CH 4, N 2, CO, HCN, and NO),more » and eleven molecular fragments (CH, CH 2, CH 3, NH, NH 2, OH, CN, COH, HCO, NOH, and HNO) were determined on the Fe(110) surface at a coverage of 0.25 monolayer. The binding strengths calculated using the PW91 functional decreased in the following order: C> CH > N > O > S > NH > COH > CN > CH2 > NOH > OH > HNO > HCO > NH2 > H > NO > HCN > CH 3 > CO > N 2 > NH 3. No stable binding structures were observed for CH 4. The estimated diffusion barriers and pathways, as well as the adsorbate-surface and intramolecular vibrational modes of all the adsorbates at their preferred binding sites, were identified. Using the calculated adsorption energetics, we constructed the potential energy surfaces for a few surface reactions including the decomposition of methane, ammonia, dinitrogen, carbon monoxide, and nitric oxide. These potential energy surfaces provide valuable insight into the ability of Fe(110) to catalyze common elementary steps.« less

The Effect of Varying Atmospheric Pressure upon Habitability and Biosignatures of Earth-like Planets.

PubMed

Keles, Engin; Grenfell, John Lee; Godolt, Mareike; Stracke, Barbara; Rauer, Heike

2018-02-01

Understanding the possible climatic conditions on rocky extrasolar planets, and thereby their potential habitability, is one of the major subjects of exoplanet research. Determining how the climate, as well as potential atmospheric biosignatures, changes under different conditions is a key aspect when studying Earth-like exoplanets. One important property is the atmospheric mass, hence pressure and its influence on the climatic conditions. Therefore, the aim of the present study is to understand the influence of atmospheric mass on climate, hence habitability, and the spectral appearance of planets with Earth-like, that is, N 2 -O 2 dominated, atmospheres orbiting the Sun at 1 AU. This work utilizes a 1D coupled, cloud-free, climate-photochemical atmospheric column model; varies atmospheric surface pressure from 0.5 to 30 bar; and investigates temperature and key species profiles, as well as emission and brightness temperature spectra in a range between 2 and 20 μm. Increasing the surface pressure up to 4 bar leads to an increase in the surface temperature due to increased greenhouse warming. Above this point, Rayleigh scattering dominates, and the surface temperature decreases, reaching surface temperatures below 273 K (approximately at ∼34 bar surface pressure). For ozone, nitrous oxide, water, methane, and carbon dioxide, the spectral response either increases with surface temperature or pressure depending on the species. Masking effects occur, for example, for the bands of the biosignatures ozone and nitrous oxide by carbon dioxide, which could be visible in low carbon dioxide atmospheres. Key Words: Planetary habitability and biosignatures-Atmospheres-Radiative transfer. Astrobiology 18, 116-132.

Investigation of wood combustion in the high-enthalpy oxidizer flow

NASA Astrophysics Data System (ADS)

Reshetnikov, S. M.; Zyryanov, I. A.; Budin, A. G.; Pozolotin, A. P.

2017-01-01

The experimental data of wood combustion in the high-enthalpy oxidizer flowresearch is presented. Combustion laws of two wood species (pine and birch) in a hybrid rocket engine (HRE) are obtained. Heat flows from the flame to the condensed phase surface are defined. The prospects of the wood use in the HRE (based on thrust characteristics) are shown.

Lighting up micromotors with quantum dots for smart chemical sensing.

PubMed

Jurado-Sánchez, B; Escarpa, A; Wang, J

2015-09-25

A new "on-the-fly" chemical optical detection strategy based on the incorporation of fluorescence CdTe quantum dots (QDs) on the surface of self-propelled tubular micromotors is presented. The motion-accelerated binding of trace Hg to the QDs selectively quenches the fluorescence emission and leads to an effective discrimination between different mercury species and other co-existing ions.

Uneven-aged management for longleaf pine: freedom to choose

Treesearch

David Dyson

2012-01-01

Longleaf pine once was present on 90 million acres of the southern landscape, ranging from coastal Virginia to east Texas and from central Florida to the mountains of Alabama. On nearly two-thirds of that area, longleaf pine grew in nearly pure (single-species) stands maintained by frequent, low-intensity surface fires of both natural and human origin. The remaining...

Towards a Quantum Dynamical Study of the H_2O+H_2O Inelastic Collision: Representation of the Potential and Preliminary Results

NASA Astrophysics Data System (ADS)

Ndengue, Steve Alexandre; Dawes, Richard

2017-06-01

Water, an essential ingredient of life, is prevalent in space and various media. H_2O in the gas phase is the major polyatomic species in the interstellar medium (ISM) and a primary target of current studies of collisional dynamics. In recent years a number of theoretical and experimental studies have been devoted to H_2O-X (with X=He, H_2, D_2, Ar, ?) elastic and inelastic collisions in an effort to understand rotational distributions of H_2O in molecular clouds. Although those studies treated several abundant species, no quantum mechanical calculation has been reported to date for a nonlinear polyatomic collider. We present in this talk the preliminary steps toward this goal, using the H_2O molecule itself as our collider, the very accurate MB-Pol surface to describe the intermolecular interaction and the MultiConfiguration Time Dependent (MCTDH) algorithm to study the dynamics. One main challenge in this effort is the need to express the Potential Energy Surface (PES) in a sum-of-products form optimal for MCTDH calculations. We will describe how this was done and present preliminary results of state-to-state probabilities.

A new Xenacanthiformes shark (Chondrichthyes, Elasmobranchii) from the Late Paleozoic Rio do Rasto Formation (Paraná Basin), Southern Brazil.

PubMed

Pauliv, Victor E; Dias, Eliseu V; Sedor, Fernando A; Ribeiro, Ana Maria

2014-03-01

The Brazilian records on Xenacanthiformes include teeth and cephalic spines from the Parnaíba, Amazonas and Paraná basins. This work describes a new species of Xenacanthidae, collected in an outcrop of Serrinha Member of Rio do Rasto Formation (Wordian to Wuchiapingian), Paraná Basin, municipality of Jacarezinho, State of Paraná. The teeth of the new species are two or three-cuspidated and the aboral surface show a smooth concavity and one rounded basal tubercle. The coronal surface presents one semi-spherical and subcircular coronal button, and also two lateral main cusps and one central (when present) with less than one fifth of the size of the lateral cusps in the labial portion. The lateral cusps are asymmetric or symmetric, rounded in transversal section, lanceolate in longitudinal section, devoid of lateral carinae and lateral serrations, and with few smooth cristae of enameloid. In optical microscope the teeth show a trabecular dentine (osteodentine) base, while the cusps are composed by orthodentine, and the pulp cavities are non-obliterated by trabecular dentine. The fossil assemblage in the same stratigraphical level and in the whole Rio do Rasto Formation indicates another freshwater record for xenacanthid sharks.

Co-immobilization of Palm and DNase I for the development of an effective anti-infective coating for catheter surfaces.

PubMed

Alves, Diana; Magalhães, Andreia; Grzywacz, Daria; Neubauer, Damian; Kamysz, Wojciech; Pereira, Maria Olívia

2016-10-15

Biomaterial-associated infections, in particular, catheter-associated infections (CAI) are a major problem in clinical practice due to their ability to resist antimicrobial treatment and the host immune system. This study aimed to co-immobilize the antimicrobial lipopeptide Palm and the enzyme DNase I to introduce both antimicrobial and anti-adhesive functionalities to polydimethylsiloxane (PDMS) material, using dopamine chemistry. Surface characterization confirmed the immobilization of both compounds and no leaching of Palm from the surfaces for up to 5days. Co-immobilization of both agents resulted in a bifunctional coating with excellent surface antimicrobial and anti-biofilm properties against both Staphylococcus aureus and Pseudomonas aeruginosa. The modified surfaces demonstrated superior biocompatibility. To better discriminate co-adhesion of both species on modified surfaces, PNA FISH (Fluorescence in situ hybridization using peptide nucleic acid probes) was employed, and results showed that P. aeruginosa was the dominant organism, with S. aureus adhering afterwards on P. aeruginosa agglomerates. Furthermore, Palm immobilization exhibited no propensity to develop bacterial resistance, as opposite to the immobilization of an antibiotic. The overall results highlighted that co-immobilization of Palm and DNase I holds great potential to be applied in the development of catheters. Catheter-associated infections (CAI) are the most common hospital-acquired infections worldwide. Several coating strategies have been proposed to fight these infections but most of them present some important limitations, including the emergence of resistant bacteria and toxicity concerns. The present work describes a two-step polydopamine-based surface modification strategy to successfully co-immobilize an antimicrobial peptide (Palm) and an enzyme targeting an important component of biofilm matrix (DNase I). This immobilization approach imparted polydimethylsiloxane surfaces with both anti-adhesive and antimicrobial properties against the adhesion of relevant bacteria as single and dual-species, with excellent stability and biocompatible and anti-biofilm properties, holding, therefore, great potential in the development of catheters able to prevent CAI. Copyright © 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Electron microscopic identification of the intestinal protozoan flagellates of the xylophagous cockroach Parasphaeria boleiriana from Brazil.

PubMed

Brugerolle, G; Silva-Neto, I D; Pellens, R; Grandcolas, P

2003-06-01

Flagellate protozoa of the hindgut of the xylophagous blattid Parasphaeria boleiriana were examined by light and electron microscopy. This species harbours two oxymonad species of the genera Monocercomonoides and Polymastix, the latter bearing Fusiformis bacteria on its surface. A diplomonad was present and has features of the genus Hexamita rather than Spironucleus. In addition, two trichomonads of the genera Monocercomonas and Tetratrichomastix were identified. A precise comparison with species of blattids and other insects was difficult because most of these flagellates have been described only by light microscopy after cell staining and there are few electron microscope studies and no molecular studies. None of the flagellates contained wood fragments in their food vacuoles and so evidently do not participate in the digestion of wood or cellulose.

Water surface locomotion in tropical canopy ants.

PubMed

Yanoviak, S P; Frederick, D N

2014-06-15

Upon falling onto the water surface, most terrestrial arthropods helplessly struggle and are quickly eaten by aquatic predators. Exceptions to this outcome mostly occur among riparian taxa that escape by walking or swimming at the water surface. Here we document sustained, directional, neustonic locomotion (i.e. surface swimming) in tropical arboreal ants. We dropped 35 species of ants into natural and artificial aquatic settings in Peru and Panama to assess their swimming ability. Ten species showed directed surface swimming at speeds >3 body lengths s(-1), with some swimming at absolute speeds >10 cm s(-1). Ten other species exhibited partial swimming ability characterized by relatively slow but directed movement. The remaining species showed no locomotory control at the surface. The phylogenetic distribution of swimming among ant genera indicates parallel evolution and a trend toward negative association with directed aerial descent behavior. Experiments with workers of Odontomachus bauri showed that they escape from the water by directing their swimming toward dark emergent objects (i.e. skototaxis). Analyses of high-speed video images indicate that Pachycondyla spp. and O. bauri use a modified alternating tripod gait when swimming; they generate thrust at the water surface via synchronized treading and rowing motions of the contralateral fore and mid legs, respectively, while the hind legs provide roll stability. These results expand the list of facultatively neustonic terrestrial taxa to include various species of tropical arboreal ants. © 2014. Published by The Company of Biologists Ltd.

Copepod communities from surface and ground waters in the everglades, south Florida

USGS Publications Warehouse

Bruno, M.C.; Cunningham, K.J.; Perry, S.A.

2003-01-01

We studied species composition and individual abundance of copepods in the surficial aquifer northeast of Everglades National Park. We identified the spatial distribution of subsurface habitats by assessing the depth of the high porosity layers in the limestone along a canal system, and we used copepods to assess the exchange between surface water and ground water along canal banks, at levels in the wells where high porosity connections to the canals exist. Surface- and ground-water taxa were defined, and species composition was related to areal position, sampling depth, and time. Subsurface copepod communities were dominated by surface copepods that disperse into the aquifer following the groundwater seepage along canal L-31N. The similarities in species composition between wells along canal reaches, suggest that copepods mainly enter ground water horizontally along canals via active and passive dispersal. Thus, the copepod populations indicate continuous connections between surface- and ground waters. The most abundant species were Orthocyclops modestus, Arctodiaptomus floridanus, Mesocyclops edax, and Thermocyclops parvus, all known in literature from surface habitats; however, these species have been collected in ground water in ENP. Only two stygophiles were collected: Diacylcops nearcticus and Diacyclops crassicaudis brachycercus. Restoration of the Everglades ecosystem requires a mosaic of data to reveal a complete picture of this complex system. The use of copepods as indicators of seepage could be a tool in helping to assess the direction and the duration of surface and ground water exchange.

Effect of breathing-hole size on the electrochemical species in a free-breathing cathode of a DMFC

NASA Astrophysics Data System (ADS)

Hwang, J. J.; Wu, S. D.; Lai, L. K.; Chen, C. K.; Lai, D. Y.

A three-dimensional numerical model is developed to study the electrochemical species characteristics in a free-breathing cathode of a direct methanol fuel cell (DMFC). A perforated current collector is attached to the porous cathode that breathes the fresh air through an array of orifices. The radius of the orifice is varied to examine its effect on the electrochemical performance. Gas flow in the porous cathode is governed by the Darcy equation with constant porosity and permeability. The multi-species diffusive transports in the porous cathode are described using the Stefan-Maxwell equation. Electrochemical reaction on the surfaces of the porous matrices is depicted via the Butler-Volmer equation. The charge transports in the porous matrices are dealt with by Ohm's law. The coupled equations are solved by a finite-element-based CFD technique. Detailed distributions of electrochemical species characteristics such as flow velocities, species mass fractions, species fluxes, and current densities are presented. The optimal breathing-hole radius is derived from the current drawn out of the porous cathode under a fixed overpotential.

Common but different: The expanding realm of Cladosporium

PubMed Central

Bensch, K.; Groenewald, J.Z.; Braun, U.; Dijksterhuis, J.; de Jesús Yáñez-Morales, M.; Crous, P.W.

2015-01-01

The genus Cladosporium (Cladosporiaceae, Dothideomycetes), which represents one of the largest genera of dematiaceous hyphomycetes, has been intensively investigated during the past decade. In the process, three major species complexes (C. cladosporioides, C. herbarum and C. sphaerospermum) were resolved based on morphology and DNA phylogeny, and a monographic revision of the genus (s. lat.) published reflecting the current taxonomic status quo. In the present study a further 19 new species are described based on phylogenetic characters (nuclear ribosomal RNA gene operon, including the internal transcribed spacer regions ITS1 and ITS2, as well as partial actin and translation elongation factor 1-α gene sequences) and morphological differences. For a selection of the species with ornamented conidia, scanning electron microscopic photos were prepared to illustrate the different types of surface ornamentation. Surprisingly, during this study Cladosporium ramotenellum was found to be a quite common saprobic species, being widely distributed and occurring on various substrates. Therefore, an emended species description is provided. Furthermore, the host range and distribution data for several previously described species are also expanded. PMID:26955200

Evaluation of Surface Cleaning of Si(211) for Molecular-Beam Epitaxy Deposition of Infrared Detectors

NASA Astrophysics Data System (ADS)

Jaime-Vasquez, M.; Jacobs, R. N.; Benson, J. D.; Stoltz, A. J.; Almeida, L. A.; Bubulac, L. O.; Chen, Y.; Brill, G.

2010-07-01

We report an assessment of the reproducibility of the HF cleaning process and As passivation prior to the nucleation of ZnTe on the Si(211) surface using temperature desorption spectroscopy, ion scattering spectroscopy, and electron spectroscopy. Observations suggest full H coverage of the Si(211) surface with mostly monohydride and small amounts of dihydride states, and that F is uniformly distributed across the top layer as a physisorbed species. Variations in major contaminants are observed across the Si surface and at the CdTe-ZnTe/Si interface. Defects act as getters for impurities present on the Si surface, and some are buried under the CdTe/ZnTe heterostructure. Overall, the data show evidence of localized concentration of major impurities around defects, supporting the hypothesis of a physical model explaining the electrical activation of defects in long-wave infrared (LWIR) HgCdTe/CdTe/Si devices.

Evaluation of Different Disinfactants on Dimensional Accuracy and Surface Quality of Type IV Gypsum Casts Retrieved from Elastomeric Impression Materials.

PubMed

Pal, P K; Kamble, Suresh S; Chaurasia, Ranjitkumar Rampratap; Chaurasia, Vishwajit Rampratap; Tiwari, Samarth; Bansal, Deepak

2014-06-01

The present study was done to evaluate the dimensional stability and surface quality of Type IV gypsum casts retrieved from disinfected elastomeric impression materials. In an in vitro study contaminated impression material with known bacterial species was disinfected with disinfectants followed by culturing the swab sample to assess reduction in level of bacterial colony. Changes in surface detail reproduction of impression were assessed fallowing disinfection. All the three disinfectants used in the study produced a 100% reduction in colony forming units of the test organisms. All the three disinfectants produced complete disinfection, and didn't cause any deterioration in surface detail reproduction. How to cite the article: Pal PK, Kamble SS, Chaurasia RR, Chaurasia VR, Tiwari S, Bansal D. Evaluation of dimensional stability and surface quality of type IV gypsum casts retrieved from disinfected elastomeric impression materials. J Int Oral Health 2014;6(3):77-81.

Electromagnetic studies of redox systems for energy storage

NASA Technical Reports Server (NTRS)

Wu, C. D.; Scherson, D.; Yeager, E.

1981-01-01

Both chromium and iron couples were studied on various electrode surfaces in acidic perchlorate solution by using rotating ring-disk techniques. It was found that chloride which forms inner sphere coordination complexes with the redox species enhances the electrode kinetics dramatically. The effects of lead underpotential deposition and surface alloy formation on the kinetics of the chromium couple on gold were studied using both linear sweep voltammetry and potential step techniques. The lad underpotential deposition was found to slow down the kinetics of the reduction of the Cr species on gold surfaces although increase the hydrogen overvoltage. The effect on the chromium kinetics can be explained in terms of principally a double layer effect. The underpotential deposition lead species with its positive charge results in a decrease in the concentration of the Cr species at the electrode surface. Similar phenomena were also observed with bismuth underpotential deposition on gold for the iron couple.

The influence of precipitation kinetics on trace element partitioning between solid and liquid solutions: A coupled fluid dynamics/thermodynamics framework to predict distribution coefficients

NASA Astrophysics Data System (ADS)

Kavner, A.

2017-12-01

In a multicomponent multiphase geochemical system undergoing a chemical reaction such as precipitation and/or dissolution, the partitioning of species between phases is determined by a combination of thermodynamic properties and transport processes. The interpretation of the observed distribution of trace elements requires models integrating coupled chemistry and mechanical transport. Here, a framework is presented that predicts the kinetic effects on the distribution of species between two reacting phases. Based on a perturbation theory combining Navier-Stokes fluid flow and chemical reactivity, the framework predicts rate-dependent partition coefficients in a variety of different systems. We present the theoretical framework, with applications to two systems: 1. species- and isotope-dependent Soret diffusion of species in a multicomponent silicate melt subjected to a temperature gradient, and 2. Elemental partitioning and isotope fractionation during precipitation of a multicomponent solid from a multicomponent liquid phase. Predictions will be compared with results from experimental studies. The approach has applications for understanding chemical exchange in at boundary layers such as the Earth's surface magmatic systems and at the core/mantle boundary.

A new species of Odorrana (Amphibia: Anura: Ranidae) from Vietnam.

PubMed

Pham, Cuong The; Nguyen, Truong Quang; Le, Minh Duc; Bonkowski, Michael; Ziegler, Thomas

2016-02-26

A new species of Odorrana is described from the karst forests in northeastern Vietnam based on morphological differences and molecular divergence. Morphologically, the new species is distinguishable from its congeners on the basis of a combination of the following diagnostic characters: (1) size large (SVL 85.9-91.6 mm in males, 108.7-110.1 mm in females); (2) head longer than wide; (3) vomerine teeth present; (4) external vocal sacs absent; (5) snout short (SL/SVL 0.16-0.17); (6) tympanum large (TD/ED 0.70 in males, 0.68 in females); (7) dorsal surface of head and anterior part of body smooth, posterior part of body and flanks with small tubercles; (8) supratympanic fold present; (9) dorsolateral fold absent; (10) webbing formula I0-0II0-0III0-1/2IV1/2-0V; (11) in life, dorsum green with dark brown spots; (12) flanks greyish brown with dark brown spots; (13) throat and chest grey, underside of limbs with large dark brown spots, edged in white, forming a network. In the phylogenetic analyses, the new species is unambiguously nested within the O. andersonii group, and placed as the sister taxon to O. wuchuanensis.

Evolution and diversity of the complement system of poikilothermic vertebrates.

PubMed

Sunyer, J O; Lambris, J D

1998-12-01

In mammals the complement system plays an important role in innate and acquired host defense mechanisms against infection and in various immunoregulatory processes. The complement system is an ancient defense mechanism that is already present in the invertebrate deuterostomes. In these species as well as in agnathans (the most primitive vertebrate species), both the alternative and lectin pathway of complement activation are already present, and the complement system appears to be involved mainly in opsonization of foreign material. With the emergence of immunoglobulins in cartilaginous fish, the classical and lytic pathways first appear. The rest of the poikilothermic species, from teleosts to reptilians, appear to contain a well-developed complement system resembling that of homeothermic vertebrates. However, important differences remain. Unlike homeotherms, several species of poikilotherms have recently been shown to possess multiple forms of complement components (C3 and factor B) that are structurally and functionally more diverse than those of higher vertebrates. It is noteworthy that the multiple forms of C3 that have been characterized in several teleost fish are able to bind with varying efficiencies to various complement-activating surfaces. We hypothesize that this diversity has allowed these animals to expand their innate capacity for immune recognition.

The Biofilm Community-Rebels with a Cause.

PubMed

Aruni, A Wilson; Dou, Yuetan; Mishra, Arunima; Fletcher, Hansel M

2015-03-01

Oral Biofilms are one of the most complex and diverse ecosystem developed by successive colonization of more than 600 bacterial taxa. Development starts with the attachment of early colonizers such as Actinomyces species and oral streptococci on the acquired pellicle and tooth enamel. These bacteria not only adhere to tooth surface but also interact with each other and lay foundation for attachment of bridging colonizer such as Fusobacterium nucleatum followed by late colonizers including the red complex species: Porphyromonas gingivalis, Tannerella forsythia and Treponema denticola -the founders of periodontal disease. As the biofilm progresses from supragingival sites to subgingival sites, the environment changes from aerobic to anaerobic thus favoring the growth of mainly Gram-negative obligate anaerobes while restricting the growth of the early Gram-positive facultative aerobes. Microbes present at supragingival level are mainly related to gingivitis and root-caries whereas subgingival species advance the destruction of teeth supporting tissues and thus causing periodontitis. This review summarizes our present understanding and recent developments on the characteristic features of supra- and subgingival biofilms, interaction between different genera and species of bacteria constituting these biofilms and draws our attention to the role of some of the recently discovered members of the oral community.

The Biofilm Community-Rebels with a Cause

PubMed Central

Aruni, A. Wilson; Dou, Yuetan; Mishra, Arunima; Fletcher, Hansel M.

2015-01-01

Oral Biofilms are one of the most complex and diverse ecosystem developed by successive colonization of more than 600 bacterial taxa. Development starts with the attachment of early colonizers such as Actinomyces species and oral streptococci on the acquired pellicle and tooth enamel. These bacteria not only adhere to tooth surface but also interact with each other and lay foundation for attachment of bridging colonizer such as Fusobacterium nucleatum followed by late colonizers including the red complex species: Porphyromonas gingivalis, Tannerella forsythia and Treponema denticola-the founders of periodontal disease. As the biofilm progresses from supragingival sites to subgingival sites, the environment changes from aerobic to anaerobic thus favoring the growth of mainly Gram-negative obligate anaerobes while restricting the growth of the early Gram-positive facultative aerobes. Microbes present at supragingival level are mainly related to gingivitis and root-caries whereas subgingival species advance the destruction of teeth supporting tissues and thus causing periodontitis. This review summarizes our present understanding and recent developments on the characteristic features of supra- and subgingival biofilms, interaction between different genera and species of bacteria constituting these biofilms and draws our attention to the role of some of the recently discovered members of the oral community. PMID:26120510

Optical properties of chitin: surface-enhanced Raman scattering substrates based on antireflection structures on cicada wings

NASA Astrophysics Data System (ADS)

Stoddart, P. R.; Cadusch, P. J.; Boyce, T. M.; Erasmus, R. M.; Comins, J. D.

2006-02-01

The transparent wings of some cicada species present ordered arrays of papillary structures with a spacing of approximately 200 nm. These structures serve an antireflection function, with optical transmission peaking at a value of approximately 98% and rising above 90% over a broad band from 450 to 2500 nm. The dimensions of the papillae are comparable to the roughness scale of surface-enhanced Raman scattering (SERS) substrates. SERS measurements performed on silver- and gold-coated wings display enhancement factors of approximately 106 with no apparent background contribution from the wing.

Unorthodox theoretical methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nedd, Sean

2012-01-01

The use of the ReaxFF force field to correlate with NMR mobilities of amine catalytic substituents on a mesoporous silica nanosphere surface is considered. The interfacing of the ReaxFF force field within the Surface Integrated Molecular Orbital/Molecular Mechanics (SIMOMM) method, in order to replicate earlier SIMOMM published data and to compare with the ReaxFF data, is discussed. The development of a new correlation consistent Composite Approach (ccCA) is presented, which incorporates the completely renormalized coupled cluster method with singles, doubles and non-iterative triples corrections towards the determination of heats of formations and reaction pathways which contain biradical species.

Principal component analysis of bacteria using surface-enhanced Raman spectroscopy

NASA Astrophysics Data System (ADS)

Guicheteau, Jason; Christesen, Steven D.

2006-05-01

Surface-enhanced Raman scattering (SERS) provides rapid fingerprinting of biomaterial in a non-destructive manner. The problem of tissue fluorescence, which can overwhelm a normal Raman signal from biological samples, is largely overcome by treatment of biomaterials with colloidal silver. This work presents a study into the applicability of qualitative SER spectroscopy with principal component analysis (PCA) for the discrimination of four biological threat simulants; Bacillus globigii, Pantoea agglomerans, Brucella noetomae, and Yersinia rohdei. We also demonstrate differentiation of gram-negative and gram-positive species and as well as spores and vegetative cells of Bacillus globigii.

A breakdown surface model for thermal backscattering from the exhaust plume of a space-based HF laser

NASA Astrophysics Data System (ADS)

Falcovitz, J.

1986-06-01

The purpose of this report is to present a breakdown surface model for evaluating thermal backscattering flow from the supersonic exhaust plume of a gaseous mixture of H, HF, H2, DF and He. Fluxes of these species are considered separately. The model is carefully analyzed and is shown to overestimate the flux. Actual flux levels of the heavy corrosive molecules (HD, DF) have been found to be exceedingly low. It is concluded that the contribution of thermal backscattering to contaminating flux of HF and DF can be neglected.

Atomic and molecular adsorption on Au(111)

DOE PAGES

Santiago-Rodriguez, Yohaselly; Herron, Jeffrey A.; Curet-Arana, Maria C.; ...

2014-05-02

Periodic self-consistent density functional theory (DFT-GGA) calculations were used to study the adsorption of several atomic species, molecular species and molecular fragments on the Au(111) surface with a coverage of 1/4 monolayer (ML). Binding geometries, binding energies, and diffusion barriers were calculated for 27 species. Furthermore, we calculated the surface deformation energy associated with the binding events. The binding strength for all the analyzed species can be ordered as follows: NH 3 < NO < CO < CH 3 < HCO < NH 2 < COOH < OH < HCOO < CNH 2 < H < N < NH

In situ supported MnOx-CeOx on carbon nanotubes for the low-temperature selective catalytic reduction of NO with NH3

NASA Astrophysics Data System (ADS)

Zhang, Dengsong; Zhang, Lei; Shi, Liyi; Fang, Cheng; Li, Hongrui; Gao, Ruihua; Huang, Lei; Zhang, Jianping

2013-01-01

The MnOx and CeOx were in situ supported on carbon nanotubes (CNTs) by a poly(sodium 4-styrenesulfonate) assisted reflux route for the low-temperature selective catalytic reduction (SCR) of NO with NH3. X-Ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), X-ray photoelectron spectroscopy (XPS), H2 temperature-programmed reduction (H2-TPR) and NH3 temperature-programmed desorption (NH3-TPD) have been used to elucidate the structure and surface properties of the obtained catalysts. It was found that the in situ prepared catalyst exhibited the highest activity and the most extensive operating-temperature window, compared to the catalysts prepared by impregnation or mechanically mixed methods. The XRD and TEM results indicated that the manganese oxide and cerium oxide species had a good dispersion on the CNT surface. The XPS results demonstrated that the higher atomic concentration of Mn existed on the surface of CNTs and the more chemisorbed oxygen species exist. The H2-TPR results suggested that there was a strong interaction between the manganese oxide and cerium oxide on the surface of CNTs. The NH3-TPD results demonstrated that the catalysts presented a larger acid amount and stronger acid strength. In addition, the obtained catalysts exhibited much higher SO2-tolerance and improved the water-resistance as compared to that prepared by impregnation or mechanically mixed methods.The MnOx and CeOx were in situ supported on carbon nanotubes (CNTs) by a poly(sodium 4-styrenesulfonate) assisted reflux route for the low-temperature selective catalytic reduction (SCR) of NO with NH3. X-Ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), X-ray photoelectron spectroscopy (XPS), H2 temperature-programmed reduction (H2-TPR) and NH3 temperature-programmed desorption (NH3-TPD) have been used to elucidate the structure and surface properties of the obtained catalysts. It was found that the in situ prepared catalyst exhibited the highest activity and the most extensive operating-temperature window, compared to the catalysts prepared by impregnation or mechanically mixed methods. The XRD and TEM results indicated that the manganese oxide and cerium oxide species had a good dispersion on the CNT surface. The XPS results demonstrated that the higher atomic concentration of Mn existed on the surface of CNTs and the more chemisorbed oxygen species exist. The H2-TPR results suggested that there was a strong interaction between the manganese oxide and cerium oxide on the surface of CNTs. The NH3-TPD results demonstrated that the catalysts presented a larger acid amount and stronger acid strength. In addition, the obtained catalysts exhibited much higher SO2-tolerance and improved the water-resistance as compared to that prepared by impregnation or mechanically mixed methods. Electronic supplementary information (ESI) available: SEM images and EDS analysis, TEM images, and XPS spectrum of samples. See DOI: 10.1039/c2nr33006g

Functional Divergence of FimX in PilZ Binding and Type IV Pilus Regulation

PubMed Central

Qi, Yaning; Xu, Linghui; Dong, Xueming; Yau, Yin Hoe; Ho, Chun Loong; Koh, Siew Lee; Shochat, Susana Geifman; Chou, Shan-Ho; Tang, Kai

2012-01-01

Type IV pili (T4P) are polar surface structures that play important roles in bacterial motility, biofilm formation, and pathogenicity. The protein FimX and its orthologs are known to mediate T4P formation in the human pathogen Pseudomonas aeruginosa and some other bacterial species. It was reported recently that FimXXAC2398 from Xanthomonas axonopodis pv. citri interacts with PilZXAC1133 directly through the nonenzymatic EAL domain of FimXXAC2398. Here we present experimental data to reveal that the strong interaction between FimXXAC2398 and PilZXAC1133 is not conserved in P. aeruginosa and likely other Pseudomonas species. In vitro and in vivo binding experiments showed that the interaction between FimX and PilZ in P. aeruginosa is below the measurable limit. Surface plasmon resonance assays further confirmed that the interaction between the P. aeruginosa proteins is at least more than 3 orders of magnitude weaker than that between the X. axonopodis pv. citri pair. The N-terminal lobe region of FimXXAC2398 was identified as the binding surface for PilZXAC1133 by amide hydrogen-deuterium exchange and site-directed mutagenesis studies. Lack of several key residues in the N-terminal lobe region of the EAL domain of FimX is likely to account for the greatly reduced binding affinity between FimX and PilZ in P. aeruginosa. All together, the results suggest that the interaction between PilZ and FimX in Xanthomonas species is not conserved in P. aeruginosa due to the evolutionary divergence among the FimX orthologs. The precise roles of FimX and PilZ in bacterial motility and T4P biogenesis are likely to vary among bacterial species. PMID:22942245

Iron Hydroxide Minerals Drive Organic and Phosphorus Chemistry in Subsurface Redox / pH Gradients

NASA Astrophysics Data System (ADS)

Flores, E.; Barge, L. M.; VanderVelde, D.; Baum, M.

2017-12-01

Iron minerals, particularly iron oxides and oxyhydroxides, are prevalent on Mars and may exist in mixed valence or even reduced states beneath the oxidized surface. Iron (II,III) hydroxides, including green rust, are reactive and potentially catalytic minerals that can absorb and concentrate charged species, while also driving chemical reactions. These minerals are highly redox-sensitive and the presence of organics and/or phosphorus species could affect their mineralogy and/or stability. Conversely, the minerals might be able to drive chemical processes such as amino acid formation, phosphorus oxyanion reactions, or could simply selectively preserve organic species via surface adsorption. In an open aqueous sediment column, soluble products of mineral-driven reactions could also diffuse to sites of different chemical conditions to react even further. We synthesized Fe-hydroxide minerals under various conditions relevant to early Earth and ancient Mars (>3.0 Gyr), anoxically and in the presence of salts likely to have been present in surface or ground waters. Using these minerals we conducted experiments to test whether iron hydroxides could promote amino acid formation, and how the reaction is affected by subsurface gradients of redox, pH, and temperature. We also tested the adsorption of organic and phosphorus species onto Fe-hydroxide minerals at different conditions within the gradients. The suite of organic or phosphorus signatures that may be found in a particular mineral system is a combination of what is synthesized there, what is preferentially concentrated / retained there, and what is preserved against degradation. Further work is needed to determine how these processes could have proceeded on Mars and what mineral-organic signatures, abiotic or otherwise, would be produced from such processes.

A new paradigm for constraining PM2.5 speciation by combining multiangular and polarimetric remote sensing with chemical transport model information

NASA Astrophysics Data System (ADS)

Kalashnikova, O.; Xu, F.; Ge, C.; Wang, J.; Garay, M. J.; Diner, D. J.

2014-12-01

Exposure to ambient particulate matter (PM) has been consistently linked to cardiovascular and respiratory health effects. Although PM is currently monitored by a network of surface stations, these are too sparsely distributed to provide the level of spatial detail needed to link different aerosol species to given health effects, and expansion to denser coverage is impractical and cost prohibitive. We present a methodology for combining Chemical Transport Model (CTM) aerosol type information and multiangular spectropolarimetric data to establish the signature of specific aerosol types in top-of-atmosphere measurements, and relate it to speciated surface PM2.5 loadings. In particular, we employ the WRF-Chem model run at the University of Nebraska, and remote sensing data from the Airborne Multiangle SpectroPolarimetric Imager (AirMSPI) to explore the feasibility of this approach. We demonstrate that the CTM does well in predicting the types of aerosols present at a given location and time, however large uncertainties currently exist in CTM estimates of the concentration of the various aerosol species (e.g., black carbon, sulfate, dust, etc.) leading to large uncertainties to model-derived speciated PM 2.5. In order to constrain CTM aerosol surface concentrations we use AirMSPI UV-VIS-NIR observations of intensity, and blue, red, and NIR observations of the Q and U Stokes parameters. We select specific scenes observed by AirMSPI and use WRF-Chem to generate an initial distribution of aerosol composition. The relevant optical properties for each aerosol species are used to calculate aerosol light scattering information. This is then used in a vector (polarized) 1-D radiative transfer model to determine at-instrument Stokes parameters for the specific AirMSPI viewing geometries. As a first step, a match is sought between the CTM-predicted radiances and the AirMSPI observations. Then, the total aerosol optical depth and fractions of various aerosol species are modified via optimization to produce a better match to the observations, and converted to PM2.5 speciated loadings using CTM aerosol vertical profiles. Finally, the results are compared to available ground-based and in situ data to validate this approach.

Morphometric characterisation of wing feathers of the barn owl Tyto alba pratincola and the pigeon Columba livia

PubMed Central

Bachmann, Thomas; Klän, Stephan; Baumgartner, Werner; Klaas, Michael; Schröder, Wolfgang; Wagner, Hermann

2007-01-01

Background Owls are known for their silent flight. Even though there is some information available on the mechanisms that lead to a reduction of noise emission, neither the morphological basis, nor the biological mechanisms of the owl's silent flight are known. Therefore, we have initiated a systematic analysis of wing morphology in both a specialist, the barn owl, and a generalist, the pigeon. This report presents a comparison between the feathers of the barn owl and the pigeon and emphasise the specific characteristics of the owl's feathers on macroscopic and microscopic level. An understanding of the features and mechanisms underlying this silent flight might eventually be employed for aerodynamic purposes and lead to a new wing design in modern aircrafts. Results A variety of different feathers (six remiges and six coverts), taken from several specimen in either species, were investigated. Quantitative analysis of digital images and scanning electron microscopy were used for a morphometric characterisation. Although both species have comparable body weights, barn owl feathers were in general larger than pigeon feathers. For both species, the depth and the area of the outer vanes of the remiges were typically smaller than those of the inner vanes. This difference was more pronounced in the barn owl than in the pigeon. Owl feathers also had lesser radiates, longer pennula, and were more translucent than pigeon feathers. The two species achieved smooth edges and regular surfaces of the vanes by different construction principles: while the angles of attachment to the rachis and the length of the barbs was nearly constant for the barn owl, these parameters varied in the pigeon. We also present a quantitative description of several characteristic features of barn owl feathers, e.g., the serrations at the leading edge of the wing, the fringes at the edges of each feather, and the velvet-like dorsal surface. Conclusion The quantitative description of the feathers and the specific structures of owl feathers can be used as a model for the construction of a biomimetic airplane wing or, in general, as a source for noise-reducing applications on any surfaces subjected to flow fields. PMID:18031576

Tutorial on Atomic Oxygen Effects and Contamination

NASA Technical Reports Server (NTRS)

Miller, Sharon K.

2017-01-01

Atomic oxygen is the most predominant specie in low Earth orbit (LEO) and is contained in the upper atmosphere of many other planetary bodies. Formed by photo-dissociation of molecular oxygen, it is highly reactive and energetic enough to break chemical bonds on the surface of many materials and react with them to form either stable or volatile oxides. The extent of the damage for spacecraft depends a lot on how much atomic oxygen arrives at the surface, the energy of the atoms, and the reactivity of the material that is exposed to it. Oxide formation can result in shrinkage, cracking, or erosion which can also result in changes in optical, thermal, or mechanical properties of the materials exposed. The extent of the reaction can be affected by mechanical loading, temperature, and other environmental components such as ultraviolet radiation or charged particles. Atomic oxygen generally causes a surface reaction, but it can scatter under coatings and into crevices causing oxidation much farther into a spacecraft surface or structure than would be expected. Contamination can also affect system performance. Contamination is generally caused by arrival of volatile species that condense on spacecraft surfaces. The volatiles are typically a result of outgassing of materials that are on the spacecraft. Once the volatiles are condensed on a surface, they can then be fixed on the surface by ultraviolet radiation andor atomic oxygen reaction to form stable surface contaminants that can change optical and thermal properties of materials in power systems, thermal systems, and sensors. This tutorial discusses atomic oxygen erosion and contaminate formation, and the effect they have on typical spacecraft materials. Scattering of atomic oxygen, some effects of combined environments and examples of effects of atomic oxygen and contamination on spacecraft systems and components will also be presented.

Surface modification of Cu metal particles by the chemical reaction between the surface oxide layer and a halogen surfactant

NASA Astrophysics Data System (ADS)

Yokoyama, Shun; Takahashi, Hideyuki; Itoh, Takashi; Motomiya, Kenichi; Tohji, Kazuyuki

2014-01-01

Surface oxides on small (2-5 μm) copper metal particles can be removed by chemical reaction with tris(2,3-dibromopropyl) isocyanurate (TIC) in diethylene glycol mono-n-hexyl ether (DGHE) solution under mild conditions where metal particles are not damaged. Surface oxides convert to copper bromide species and subsequently dissolve into the solvent. It was found that resultant surface species are resistant to re-oxidation due to remaining surface bromides. This finding opens up a possibility to create microclines based on cheap copper nanoparticles.

Diversity and Significance of Mold Species in Norwegian Drinking Water▿

PubMed Central

Hageskal, Gunhild; Knutsen, Ann Kristin; Gaustad, Peter; de Hoog, G. Sybren; Skaar, Ida

2006-01-01

In order to determine the occurrence, distribution, and significance of mold species in groundwater- and surface water-derived drinking water in Norway, molds isolated from 273 water samples were identified. Samples of raw water, treated water, and water from private homes and hospital installations were analyzed by incubation of 100-ml membrane-filtered samples on dichloran-18% glycerol agar. The total count (number of CFU per 100 ml) of fungal species and the species diversity within each sample were determined. The identification of mold species was based on morphological and molecular methods. In total, 94 mold species belonging to 30 genera were identified. The mycobiota was dominated by species of Penicillium, Trichoderma, and Aspergillus, with some of them occurring throughout the drinking water system. Several of the same species as isolated from water may have the potential to cause allergic reactions or disease in humans. Other species are common contaminants of food and beverages, and some may cause unwanted changes in the taste or smell of water. The present results indicate that the mycobiota of water should be considered when the microbiological safety and quality of drinking water are assessed. In fact, molds in drinking water should possibly be included in the Norwegian water supply and drinking water regulations. PMID:17028226

A new species of Allobates (Anura: Aromobatidae) from the Tapajós River basin, Pará State, Brazil.

PubMed

Lima, Albertina P; Simões, Pedro Ivo; Kaefer, Igor Luis

2014-12-02

We describe a new species of Allobates from the south of eastern Amazonia, Brazil. This species inhabits fluvial springs and the banks of small streams in terra-firme forests along the Tapajós River basin. Average snout-to-vent length is 17.78 mm (range 16.09-19.59 mm) among males and 19.50 mm (range 17.97-20.84 mm) among females. Surface of dorsum is marked by a distinct dark color pattern, with three convex areas, triangle and diamond-shaped. The species has a diffuse pale dorsolateral line (absent in some specimens), while the oblique lateral bar is defined. Dark-brown transversal stripes are present on femoral and tibial dorsal surfaces, which align with each other in live specimens when at rest. Tadpoles have short papillae on anterior (8-10 papillae on each side) and posterior labium (>30 papillae). Posterior labium is projected to the front, hiding posterior tooth rows. Eggs are deposited in nests on rolled or cranked dead leaves on the forest floor. Egg membranes and jelly-nests are transparent. Advertisement calls are mainly characterized by the continuous emission of single notes that might shift sporadically to note-pairs, emitted during short periods. Notes are split by regular silent intervals, with peak frequency ranging between 4273-4867 Hz. 

Fungal contamination assessment in Portuguese elderly care centers.

PubMed

Viegas, C; Almeida-Silva, M; Gomes, A Quintal; Wolterbeek, H T; Almeida, S M

2014-01-01

Individuals spend 80-90% of their day indoors and elderly subjects are likely to spend even a greater amount of time indoors. Thus, indoor air pollutants such as bioaerosols may exert a significant impact on this age group. The aim of this study was to characterize fungal contamination within Portuguese elderly care centers. Fungi were measured using conventional as well as molecular methods in bedrooms, living rooms, canteens, storage areas, and outdoors. Bioaerosols were evaluated before and after the microenvironments' occupancy in order to understand the role played by occupancy in fungal contamination. Fungal load results varied from 32 colony-forming units CFU m(-3) in bedrooms to 228 CFU m(-3) in storage areas. Penicillium sp. was the most frequently isolated (38.1%), followed by Aspergillus sp. (16.3%) and Chrysonilia sp. (4.2%). With respect to Aspergillus genus, three different fungal species in indoor air were detected, with A. candidus (62.5%) the most prevalent. On surfaces, 40 different fungal species were isolated and the most frequent was Penicillium sp. (22.2%), followed by Aspergillus sp. (17.3%). Real-time polymerase chain reaction did not detect the presence of A. fumigatus complex. Species from Penicillium and Aspergillus genera were the most abundant in air and surfaces. The species A. fumigatus was present in 12.5% of all indoor microenvironments assessed. The living room was the indoor microenvironment with lowest fungal concentration and the storage area was highest.

Trichoderma species form endophytic associations within Theobroma cacao trichomes.

PubMed

Bailey, Bryan A; Strem, Mary D; Wood, Delilah

2009-12-01

Trichoderma species are usually considered soil organisms that colonize plant roots, sometimes forming a symbiotic relationship. Recent studies demonstrate that Trichoderma species are also capable of colonizing the above ground tissues of Theobroma cacao (cacao) in what has been characterized as an endophytic relationship. Trichoderma species can be re-isolated from surface sterilized cacao stem tissue, including the bark and xylem, the apical meristem, and to a lesser degree from leaves. SEM analysis of cacao stems colonized by strains of four Trichoderma species (Trichoderma ovalisporum-DIS 70a, Trichoderma hamatum-DIS 219b, Trichoderma koningiopsis-DIS 172ai, or Trichoderma harzianum-DIS 219f) showed a preference for surface colonization of glandular trichomes versus non-glandular trichomes. The Trichoderma strains colonized the glandular trichome tips and formed swellings resembling appresoria. Hyphae were observed emerging from the glandular trichomes on surface sterilized stems from cacao seedlings that had been inoculated with each of the four Trichoderma strains. Fungal hyphae were observed under the microscope emerging from the trichomes as soon as 6h after their isolation from surface sterilized cacao seedling stems. Hyphae were also observed, in some cases, emerging from stalk cells opposite the trichome head. Repeated single trichome/hyphae isolations verified that the emerging hyphae were the Trichoderma strains with which the cacao seedlings had been inoculated. Strains of four Trichoderma species were able to enter glandular trichomes during the colonization of cacao stems where they survived surface sterilization and could be re-isolated. The penetration of cacao trichomes may provide the entry point for Trichoderma species into the cacao stem allowing systemic colonization of this tissue.

Use of Novel Surfaces to Reduce Bioadhesion on Infrastructure

DTIC Science & Technology

2010-06-01

Research and Development Center Model species selection • Terrestrial gastropod  Danger to crops  Intermediate host to pathogens  Nocturnal...TBT  Non-target species, legacy contamination  Laborious • Bio-inspiration: leverage biological surfaces that have adapted unique properties... Adapted over 1000s of years • Hypothesis: microstructured pattern tessellations, hydrophobicity, surface properties or hybridizations will reduce

Numerical study of the influence of surface reaction probabilities on reactive species in an rf atmospheric pressure plasma containing humidity

NASA Astrophysics Data System (ADS)

Schröter, Sandra; Gibson, Andrew R.; Kushner, Mark J.; Gans, Timo; O'Connell, Deborah

2018-01-01

The quantification and control of reactive species (RS) in atmospheric pressure plasmas (APPs) is of great interest for their technological applications, in particular in biomedicine. Of key importance in simulating the densities of these species are fundamental data on their production and destruction. In particular, data concerning particle-surface reaction probabilities in APPs are scarce, with most of these probabilities measured in low-pressure systems. In this work, the role of surface reaction probabilities, γ, of reactive neutral species (H, O and OH) on neutral particle densities in a He-H2O radio-frequency micro APP jet (COST-μ APPJ) are investigated using a global model. It is found that the choice of γ, particularly for low-mass species having large diffusivities, such as H, can change computed species densities significantly. The importance of γ even at elevated pressures offers potential for tailoring the RS composition of atmospheric pressure microplasmas by choosing different wall materials or plasma geometries.

A new species of Aspidoras Ihering (Siluriformes: Callichthyidae: Corydoradinae) from the Rio Xingu Basin, Pará, Brazil.

PubMed

Leão, Manuela D V; Britto, Marcelo R; Wosiacki, Wolmar B

2015-07-21

A new species of Aspidoras is described from an unnamed stream in the Rio Xingu Basin, Castelo de Sonhos municipality, Pará State, representing the northernmost record of the genus along the edge of the Brazilian Shield in the Amazon Basin. Aspidoras marianae is easily distinguished from all congeners in having minute odontode-bearing platelets scattered over the surface of the snout region, minute platelets between the parieto-supraoccipital process and the nuchal plate, and other shared features related to color pattern, morphometrics, meristics and morphological data. Comments about exclusive and shared features are presented.

Measurements of reflectance spectra of ion-bombarded ice and application to surfaces in the outer solar system

NASA Technical Reports Server (NTRS)

O'Shaughnessy, D. J.; Boring, J. W.; Johnson, R. E.

1988-01-01

The first results of laboratory measurements of the wavelength dependence of the alternation of the visible reflectance of H2O ice irradiated by keV ions are presented. When the implanted species is chemically neutral, absorption is slightly enhanced below 0.55 micron. For an incident species containing sulfur, a strong absorption feature is produced at 0.4 micron, probably corresponding to S3. This occurs at too large a wavelength to account for the absorption feature observed at Europa by Voyager and therefore casts doubt on the recent interpretation of the reflectance data of Europa.

Spore-Forming Bacteria that Resist Sterilization

NASA Technical Reports Server (NTRS)

LaDuc, Myron; Venkateswaran, Kasthuri

2003-01-01

A report presents a phenotypic and genotypic characterization of a bacterial species that has been found to be of the genus Bacillus and has been tentatively named B. odysseensis because it was isolated from surfaces of the Mars Odyssey spacecraft as part of continuing research on techniques for sterilizing spacecraft to prevent contamination of remote planets by terrestrial species. B. odysseensis is a Gram-positive, facultatively anaerobic, rod-shaped bacterium that forms round spores. The exosporium has been conjectured to play a role in the elevated resistance to sterilization. Research on the exosporium is proposed as a path toward improved means of sterilization, medical treatment, and prevention of biofouling.

Velocity of climate change algorithms for guiding conservation and management.

PubMed

Hamann, Andreas; Roberts, David R; Barber, Quinn E; Carroll, Carlos; Nielsen, Scott E

2015-02-01

The velocity of climate change is an elegant analytical concept that can be used to evaluate the exposure of organisms to climate change. In essence, one divides the rate of climate change by the rate of spatial climate variability to obtain a speed at which species must migrate over the surface of the earth to maintain constant climate conditions. However, to apply the algorithm for conservation and management purposes, additional information is needed to improve realism at local scales. For example, destination information is needed to ensure that vectors describing speed and direction of required migration do not point toward a climatic cul-de-sac by pointing beyond mountain tops. Here, we present an analytical approach that conforms to standard velocity algorithms if climate equivalents are nearby. Otherwise, the algorithm extends the search for climate refugia, which can be expanded to search for multivariate climate matches. With source and destination information available, forward and backward velocities can be calculated allowing useful inferences about conservation of species (present-to-future velocities) and management of species populations (future-to-present velocities). © 2014 The Authors. Global Change Biology Published by John Wiley & Sons Ltd.

Isotope separation by photochromatography

DOEpatents

Suslick, Kenneth S.

1977-01-01

An isotope separation method which comprises physically adsorbing an isotopically mixed molecular species on an adsorptive surface and irradiating the adsorbed molecules with radiation of a predetermined wavelength which will selectively excite a desired isotopic species. Sufficient energy is transferred to the excited molecules to desorb them from the surface and thereby separate them from the unexcited undesired isotopic species. The method is particularly applicable to the separation of hydrogen isotopes.

Engineering nanoscale surface features to sustain microparticle rolling in flow.

PubMed

Kalasin, Surachate; Santore, Maria M

2015-05-26

Nanoscopic features of channel walls are often engineered to facilitate microfluidic transport, for instance when surface charge enables electro-osmosis or when grooves drive mixing. The dynamic or rolling adhesion of flowing microparticles on a channel wall holds potential to accomplish particle sorting or to selectively transfer reactive species or signals between the wall and flowing particles. Inspired by cell rolling under the direction of adhesion molecules called selectins, we present an engineered platform in which the rolling of flowing microparticles is sustained through the incorporation of entirely synthetic, discrete, nanoscale, attractive features into the nonadhesive (electrostatically repulsive) surface of a flow channel. Focusing on one example or type of nanoscale feature and probing the impact of broad systematic variations in surface feature loading and processing parameters, this study demonstrates how relatively flat, weakly adhesive nanoscale features, positioned with average spacings on the order of tens of nanometers, can produce sustained microparticle rolling. We further demonstrate how the rolling velocity and travel distance depend on flow and surface design. We identify classes of related surfaces that fail to support rolling and present a state space that identifies combinations of surface and processing variables corresponding to transitions between rolling, free particle motion, and arrest. Finally we identify combinations of parameters (surface length scales, particle size, flow rates) where particles can be manipulated with size-selectivity.

Hairy and Slippery Polyoxazoline-Based Copolymers on Model and Cartilage Surfaces.

PubMed

Morgese, Giulia; Ramakrishna, Shivaprakash N; Simic, Rok; Zenobi-Wong, Marcy; Benetti, Edmondo M

2018-02-12

Comb-like polymers presenting a hydroxybenzaldehyde (HBA)-functionalized poly(glutamic acid) (PGA) backbone and poly(2-methyl-2-oxazoline) (PMOXA) side chains chemisorb on aminolized substrates, including cartilage surfaces, forming layers that reduce protein contamination and provide lubrication. The structure, physicochemical, biopassive, and tribological properties of PGA-PMOXA-HBA films are finely determined by the copolymer architecture, its reactivity toward the surface, i.e. PMOXA side-chain crowding and HBA density, and by the copolymer solution concentration during assembly. Highly reactive species with low PMOXA content form inhomogeneous layers due to the limited possibility of surface rearrangements by strongly anchored copolymers, just partially protecting the functionalized surface from protein contamination and providing a relatively weak lubrication on cartilage. Biopassivity and lubrication can be improved by increasing copolymer concentration during assembly, leading to a progressive saturation of surface defects across the films. In a different way, less reactive copolymers presenting high PMOXA side-chain densities form uniform, biopassive, and lubricious films, both on model aminolized silicon oxide surfaces, as well as on cartilage substrates. When assembled at low concentrations these copolymers adopt a "lying down" conformation, i.e. adhering via their backbones onto the substrates, while at high concentrations they undergo a conformational transition, assuming a more densely packed, "standing up" structure, where they stretch perpendicularly from the substrate. This specific arrangement reduces protein contamination and improves lubrication both on model as well as on cartilage surfaces.

Surface analysis of space telescope material specimens

NASA Technical Reports Server (NTRS)

Fromhold, A. T.; Daneshvar, K.

1985-01-01

Qualitative and quantitative data on Space Telescope materials which were exposed to low Earth orbital atomic oxygen in a controlled experiment during the 41-G (STS-17) mission were obtained utilizing the experimental techniques of Rutherford backscattering (RBS), particle induced X-ray emission (PIXE), and ellipsometry (ELL). The techniques employed were chosen with a view towards appropriateness for the sample in question, after consultation with NASA scientific personnel who provided the material specimens. A group of eight samples and their controls selected by NASA scientists were measured before and after flight. Information reported herein include specimen surface characterization by ellipsometry techniques, a determination of the thickness of the evaporated metal specimens by RBS, and a determination of trace impurity species present on and within the surface by PIXE.

Temporal response of a surface flashover on a velvet cathode in a relativistic diode

DOE PAGES

Coleman, J. E.; Moir, D. C.; Crawford, M. T.; ...

2015-03-11

Surface flashover of a carbon fiber velvet cathode generates a discharge from which electrons are relativistically accelerated to γ ranging from 4.9 to 8.8 through a 17.8 cm diode. This discharge is assumed to be a hydrocarbon mixture. Our objective is to quantify the dynamics over the ~100 ns pulse of the plasma discharge generated on the surface of the velvet cathode and across the anode-cathode (A-K) gap. We present a qualitative comparison of calculated and measured results, which includes time resolved measurements with a photomultiplier tube and charge-coupled device images. Additionally, initial visible spectroscopy measurements will also be presentedmore » confirming the ion species are dominated by hydrogen.« less

Listeria monocytogenes-carrying consortia in food industry. Composition, subtyping and numerical characterisation of mono-species biofilm dynamics on stainless steel.

PubMed

Rodríguez-López, Pedro; Saá-Ibusquiza, Paula; Mosquera-Fernández, Maruxa; López-Cabo, Marta

2015-08-03

In order to find out how real Listeria monocytogenes-carrying biofilms are in industrial settings, a total of 270 environmental samples belonging to work surfaces from fish (n = 123), meat (n = 75) and dairy industries (n = 72) were analysed in order to detect L. monocytogenes. 12 samples were positive for L. monocytogenes and a total of 18 different species were identified as accompanying microbiota in fish and meat industry. No L. monocytogenes was found in samples from dairy industry. Molecular characterisation combining results of AscI and ApaI macrorestriction PFGE assays yielded 7 different subtypes of L. monocytogenes sharing in 71.43% of cases the same serogroup (1/2a-3a). Results from dynamic numerical characterisation between L. monocytogenes monospecies biofilms on stainless steel (SS) using MATLAB-based tool BIOFILMDIVER demonstrated that except in isolate A1, in which a significant increase in the percentage of covered area (CA), average diffusion distance (ADD) and maximum diffusion distance (MDD) was observed after 120 h of culture, no significant differences were observed in the dynamics of the rest of the L. monocytogenes isolates. Quantitative dual-species biofilm association experiments performed on SS indicated that L. monocytogenes cell counts presented lower values in mixed-species cultures with certain species at 24 and 48 h compared with mono-species culture. However, they remained unaltered after 72 h except when co-cultured with Serratia fonticola which presented differences in all sampling times and was also the dominant species within the dual-species biofilm. When considering frequency of appearance of accompanying species, an ecological distribution was demonstrated as Escherichia coli appeared to be the most abundant in fish industry and Carnobacterium spp. in meat industry. Copyright © 2015 Elsevier B.V. All rights reserved.

Microwave plasma induced surface modification of diamond-like carbon films

NASA Astrophysics Data System (ADS)

Rao Polaki, Shyamala; Kumar, Niranjan; Gopala Krishna, Nanda; Madapu, Kishore; Kamruddin, Mohamed; Dash, Sitaram; Tyagi, Ashok Kumar

2017-12-01

Tailoring the surface of diamond-like carbon (DLC) film is technically relevant for altering the physical and chemical properties, desirable for useful applications. A physically smooth and sp3 dominated DLC film with tetrahedral coordination was prepared by plasma-enhanced chemical vapor deposition technique. The surface of the DLC film was exposed to hydrogen, oxygen and nitrogen plasma for physical and chemical modifications. The surface modification was based on the concept of adsorption-desorption of plasma species and surface entities of films. Energetic chemical species of microwave plasma are adsorbed, leading to desorbtion of the surface carbon atoms due to energy and momentum exchange. The interaction of such reactive species with DLC films enhanced the roughness, surface defects and dangling bonds of carbon atoms. Adsorbed hydrogen, oxygen and nitrogen formed a covalent network while saturating the dangling carbon bonds around the tetrahedral sp3 valency. The modified surface chemical affinity depends upon the charge carriers and electron covalency of the adsorbed atoms. The contact angle of chemically reconstructed surface increases when a water droplet interacts either through hydrogen or van dear Waals bonding. These weak interactions influenced the wetting property of the DLC surface to a great extent.

Steric Effect and Evolution of Surface Species in the Hydrodeoxygenation of Bio-Oil Model Compounds over Pt/HBEA

DOE PAGES

Foo, Guo Shiou; Rogers, Allyson K.; Yung, Matthew M.; ...

2016-01-11

The hydrodeoxygenation of various bio-oil model compounds (anisole, m-cresol and guaiacol) over Pt/HBEA and the evolution of surface species is investigated. Depending on the functional group, different surface species are formed when the compounds are adsorbed in the presence of Lewis acid sites. For anisole, the methoxy group is decomposed to form phenate species. The methyl and methoxy group remains intact on m-cresol and guaiacol to form cresolate and methoxy phenate species, respectively. The position of these functional groups have a strong influence in the degree of hydrodeoxygenation due to steric hindrance. Based on operando transmission FTIR spectroscopy, a timelinemore » for the formation of polynuclear aromatics and catalyst deactivation is constructed, which is also dependent on the substituents. The slow deactivation rate and low carbon content on Pt/HBEA is discussed.« less

Clay mineralogy of surface sediments as a tool for deciphering river contributions to the Cariaco Basin (Venezuela)

NASA Astrophysics Data System (ADS)

Bout-Roumazeilles, V.; Riboulleau, A.; du Châtelet, E. Armynot; Lorenzoni, L.; Tribovillard, N.; Murray, R. W.; Müller-Karger, F.; Astor, Y. M.

2013-02-01

The mineralogical composition of 95 surface sediment samples from the Cariaco Basin continental shelf and Orinoco delta was investigated in order to constrain the clay-mineral main provenance and distribution within the Cariaco Basin. The spatial variability of the data set was studied using a geo-statistical approach that allows drawing representative clay-mineral distribution maps. These maps are used to identify present-day dominant sources for each clay-mineral species in agreement with the geological characteristics of the main river watersheds emptying into the basin. This approach allows (1) identifying the most distinctive clay-mineral species/ratios that determine particle provenance, (2) evaluating the respective contribution of local rivers, and (3) confirming the minimal present-day influence of the Orinoco plume on the Cariaco Basin sedimentation. The Tuy, Unare, and Neveri Rivers are the main sources of clay particles to the Cariaco Basin sedimentation. At present, the Tuy River is the main contributor of illite to the western part of the southern Cariaco Basin continental shelf. The Unare River plume, carrying smectite and kaolinite, has a wide westward propagation, whereas the Neveri River contribution is less extended, providing kaolinite and illite toward the eastern Cariaco Basin. The Manzanares, Araya, Tortuga, and Margarita areas are secondary sources of local influence. These insights shed light on the origin of present-day terrigenous sediments of the Cariaco Basin and help to propose alternative explanations for the temporal variability of clay mineralogy observed in previously published studies.

Identification of endangered or threatened Costa Rican tree species by wood anatomy and fluorescence activity.

PubMed

Moya, Róger; Wiemann, Michael C; Olivares, Carlos

2013-09-01

A total of 45 native Costa Rican tree species are threatened or in danger of extinction, but the Convention on International Trade Endangered Species (CITES) includes only eight of these in its Appendices. However, the identification of other species based on their wood anatomy is limited. The present study objective was to describe and to compare wood anatomy and fluorescence activity in some endangered or threatened species of Costa Rica. A total of 45 (22 endangered and 23 threatened with extinction) wood samples of these species, from the xylaria of the Instituto Tecnológico de Costa Rica and the Forest Products Laboratory in Madison, Wisconsin, were examined. Surface fluorescence was positive in eight species, water extract fluorescence was positive in six species and ethanol extract fluorescence was positive in 24 species. Almost all species were diffuse porous except for occasional (Cedrela odorata, C. fissilis, Cordia gerascanthus) or regular (C. salvadorensis and C. tonduzii) semi-ring porosity. A dendritic vessel arrangement was found in Sideroxylon capari, and pores were solitary in Guaiacum sanctum and Vantanea barbourii. Vessel element length was shortest in Guaiacum sanctum and longest in Humiriastrum guianensis, Minquartia guianensis and Vantanea barbourii. Finally, anatomical information and fluorescence activity were utilized to construct an identification key of species, in which fluorescence is a feature used in identification.

Stictonectes abellani sp. n. (Coleoptera: Dytiscidae: Hydroporinae) from the Iberian Peninsula, with notes on the phylogeny, ecology and distribution of the Iberian species of the genus.

PubMed

Millán, Andrés; Picazo, Félix; Fery, Hans; Moreno, José Luis; Sánchez-Fernández, David

2013-12-09

Stictonectes abellani sp. n. is described from the Iberian Peninsula. On average, the new species is larger and the colouration of the upper surface darker than in most other species of the genus. Seemingly the species has been confounded with others in the past, particularly S. optatus (Seidlitz, 1887). Males can be separated from externally similar species by studying the shape of the parameres. Additionally, the anterior margin of the clypeus is provided with a distinct rim in both sexes, which is absent or only weakly present in other species. The habitus and the male genitalia of the new species are illustrated, and compared with those of S. optatus. External morphological differences from other members of the genus are discussed. According to studies of the molecular phylogeny, based on fragments of four mitochondrial genes, S. abellani sp. n. is clearly separated from previously described species of Stictonectes Brinck, 1943, apparently being relatively basal within the genus. The new species is rather widely distributed in the south-western part of the Iberian Peninsula, inhabiting pools in small temporary siliceous streams. We provide distributional maps for all eight Iberian Stictonectes and estimate the potential distributional areas of the new species and the other two endemic Iberian species S. occidentalis Fresneda & Fery, 1990 and S. rebeccae Bilton, 2011, based on environmental niche modelling. 

A new species of Diapus Chapuis from South-West China and North Thailand (Coleoptera: Curculionidae: Platypodinae).

PubMed

Knížek, M; Beaver, R A; Liu, L-Y

2015-12-16

The genus Diapus Chapuis was erected (Chapuis 1865) for four species of pinhole borer (Curculionidae: Platypodinae) from the Oriental region and New Guinea. It was distinguished from other platypodine genera primarily by the widely separated procoxae (Chapuis 1865). Hopkins (1914) designated Diapus quadrispinatus Chapuis, 1865 as the type species of the genus. The genus is currently placed in the platypodine tribe Tesserocerini, subtribe Diapodina (Alonso-Zarazaga & Lyal 2009). Only two genera are included in the Diapodina, Diapus and Genyocerus Motschulsky (Alonso-Zarazaga & Lyal 2009, Jordal 2015). Diapus is distinguished from Genyocerus by the following characters (Wood 1993, Beaver & Liu 2007): 1. In Diapus, the scutellum is narrower and more sunken, not flush with the elytral surface posteriorly as it is in Genyocerus. 2. The mycangial pores of Diapus are sometimes fused to form a transverse or crescentic bar on each side of the midline of the pronotum. This does not occur in Genyocerus. 3. The antennal club of Diapus sometimes has a median testaceous strip lacking sensillae on the anterior face. This strip is never present in Genyocerus. 4. The males of Diapus never possess a membranous extension of the apical margin of the fourth abdominal ventrite, present in some species of Genyocerus. 5. The females of Diapus often bear deciduous mandibular appendages, which are never present in Genyocerus (Beaver & Liu 2007).

Temperature estimation from molecular nitrogen UV spectra in atmospheric pressure plasmas

NASA Astrophysics Data System (ADS)

Pepper, Keenan; Kim, Yongho; Kim, Jihun

2008-11-01

Atmospheric pressure plasmas have many potential applications to fuel processing, surface treatment, and manipulation of chemical reactions. These plasmas are often non-thermal, which means different species are not in equilibrium and have different effective temperatures. This is critical for many applications because it allows high concentrations of reactive species to be produced without using a prohibitive amount of power. In the present work, numerical software was developed to estimate the vibrational and rotational temperatures (Tvib and Trot) of N2 molecules from their ultraviolet emission spectra. The electron temperature Te can also be estimated by comparing the N2 spectrum to that of the N2^+ molecular ion. This technique is applied to several plasma sources including audio frequency, RF, and microwave devices. The results are presented and their implications for practical applications are discussed.

Towards Mechanistic Understanding of Mercury Availability and Toxicity to Aquatic Primary Producers.

PubMed

Dranguet, Perrine; Flück, Rebecca; Regier, Nicole; Cosio, Claudia; Le Faucheur, Séverine; Slaveykova, Vera I

2014-11-01

The present article reviews current knowledge and recent progress on the bioavailability and toxicity of mercury to aquatic primary producers. Mercury is a ubiquitous toxic trace element of global concern. At the base of the food web, primary producers are central for mercury incorporation into the food web. Here, the emphasis is on key, but still poorly understood, processes governing the interactions between mercury species and phytoplankton, and macrophytes, two representatives of primary producers. Mass transfer to biota surface, adsorption to cell wall, internalization and release from cells, as well as underlying toxicity mechanisms of both inorganic mercury and methylmercury are discussed critically. In addition, the intracellular distribution and transformation processes, their importance for mercury toxicity, species-sensitivity differences and trophic transfer are presented. The mini-review is illustrated with examples of our own research.

Microflora analysis of a child with severe combined immune deficiency

NASA Technical Reports Server (NTRS)

Taylor, G. R.; Kropp, K. D.; Molina, T. C.

1978-01-01

The paper presents a microflora analysis of a 5-year-old male child with severe combined immune deficiency who was delivered by Caesarean section and continuously maintained in an isolator. Despite precautions, it was found that the child had come in contact with at least 54 different microbial contaminants. While his skin autoflora was similar to that of a reference group of healthy male adults in numbers of different species and the number of viable cells present per square centimeter of surface area, the subject's autoflora differed from the reference group in that significantly fewer anaerobic species were recovered from the patient's mouth and feces. It is suggested that the child's remaining disease free shows that the reported bacteria are noninvasive or that the unaffected components of the child's immune defense mechanisms are important.

Physical Alteration of Martian Dust Grains, Its Influence on Detection of Clays and Identification of Aqueous Processes on Mars

NASA Technical Reports Server (NTRS)

Bishop, Janice L.; Drief, Ahmed; Dyar, Darby

2003-01-01

Clays, if present on Mars, have been illusive. Determining whether or not clay minerals and other aqueous alteration species are present on Mars provides key information about the extent and duration of aqueous processes on Mars. The purpose of this study is to characterize in detail changes in the mineral grains resulting from grinding and to assess the influence of physical processes on clay minerals on the surface of Mars. Physical alteration through grinding was shown to greatly affect the structure and a number of properties of antigorite and kaolinite. This project builds on an initial study and includes a combination of SEM, HRTEM, reflectance and M ssbauer spectroscopies. Grain size was found to decrease, as expected, with grinding. In addition, nanophase carbonate, Si-OH and iron oxide species were formed.

Effects of Hydration and Oxygen Vacancy on CO2 Adsorption and Activation on β-Ga2O3(100)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Yunxiang; Liu, Chang-jun; Mei, Donghai

The effects of hydration and oxygen vacancy on CO2 adsorption on the β-Ga2O3(100) surface have been studied using density functional theory slab calculations. Adsorbed CO2 is activated on the dry perfect β-Ga2O3(100) surface, resulting in a carbonate species. This adsorption is slightly endothermic, with an adsorption energy of 0.07 eV. Water is preferably adsorbed molecularly on the dry perfect β-Ga2O3(100) surface with an adsorption energy of -0.56 eV, producing a hydrated perfect β-Ga2O3(100) surface. Adsorption of CO2 on the hydrated surface as a carbonate species is also endothermic, with an adsorption energy of 0.14 eV, indicating a slight repulsive interactionmore » when H2O and CO2 are coadsorbed. The carbonate species on the hydrated perfect surface can be protonated by the co-adsorbed H2O to a bicarbonate species, making the overall process exothermic with an adsorption energy of -0.13 eV. The effect of defects on CO2 adsorption and activation has been examined by creating an oxygen vacancy on the dry β-Ga2O3(100) surface. The formation of an oxygen vacancy is endothermic, by 0.34 eV, with respect to a free O2 molecule in the gas phase. Presence of the oxygen vacancy promoted the adsorption and activation of CO2. In the most stable CO2 adsorption configuration on the dry defective β-Ga2O3(100) surface with an oxygen vacancy, one of the oxygen atoms of the adsorbed CO2 occupies the oxygen vacancy site and the CO2 adsorption energy is -0.31 eV. Water favors dissociative adsorption at the oxygen vacancy site on the defective surface. This process is instantaneous with an adsorption energy of -0.62 eV. These results indicate that, when water and CO2 are both present in the adsorption system simultaneously, the water molecule will compete with CO2 for the oxygen vacancy sites and impact CO2 adsorption and conversion negatively. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy. A portion of the computing time was granted by the scientific user projects using the Molecular Science Computing Facility in the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL). The EMSL is a DOE national scientific user facility located at PNNL, and supported by the DOE’s Office of Science, Biological and Environmental Research.« less

Morphofunctional structure of the lingual papillae in three species of South American Camelids: Alpaca, guanaco, and llama.

PubMed

Erdoğan, Serkan; Villar Arias, Silvia; Pérez, William

2016-02-01

The aim of this study was to compare the anatomical and functional characteristics of the lingual papilla among the Camelidae. For this purpose, tongues of alpaca, guanaco, and llama were used. Numerous long and thin filiform papillae were located in the median groove and none were detected on the rest of the dorsal surface of the lingual apex in alpaca. Secondary papillae originated from the base of some filiform papillae on the ventral surface of alpaca tongue. The bases of some filiform papillae of the lateral surface of the lingual apex were inserted into conspicuous grooves in guanaco and tips of filiform papillae on the dorsal surface of the lingual body were ended by bifurcated apex. On the dorsal surface of the lingual apex of llama, there were no filiform papillae but there were numerous filiform papillae on both the lateral margins of the ventral surface of the lingual apex. Fungiform papillae were distributed randomly on dorsal lingual surface and ventral margins of the tongues of all camelid species. Lenticular papillae were located on the lingual torus and varied in size and topographical distribution for each species. Circumvallate papillae had irregular surfaces in llama and alpaca, and smooth surface in guanaco. In conclusion, llama and alpaca tongues were more similar to each other, and tongues of all camelid species displayed more similarities to those of Bactrian and dromedary camels in comparison with other herbivores and ruminants. © 2015 Wiley Periodicals, Inc.

Influence of LaFeO 3 Surface Termination on Water Reactivity

DOE PAGES

Stoerzinger, Kelsey A.; Comes, Ryan; Spurgeon, Steven R.; ...

2017-02-16

The polarity of oxide surfaces can dramatically impact their surface reactivity, in particular, with polar molecules such as water. The surface species that result from this interaction change the oxide electronic structure and chemical reactivity in applications such as photoelectrochemistry but are challenging to probe experimentally. Here, we report a detailed study of the surface chemistry and electronic structure of the perovskite LaFeO 3 in humid conditions using ambient-pressure X-ray photoelectron spectroscopy. In comparing the two possible terminations of the polar (001)-oriented surface, we find that the LaO-terminated surface is more reactive toward water, forming hydroxyl species and adsorbing molecularmore » water at lower relative humidity than its FeO 2-terminated counterpart. But, the FeO 2-terminated surface forms more hydroxyl species during water adsorption at higher humidity, suggesting that adsorbate–adsorbate interactions may impact reactivity. These results demonstrate how the termination of a complex oxide can dramatically impact its reactivity, providing insight that can aid in the design of catalyst materials.« less

Influence of LaFeO 3 Surface Termination on Water Reactivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoerzinger, Kelsey A.; Comes, Ryan; Spurgeon, Steven R.

The polarity of oxide surfaces can dramatically impact their surface reactivity, in particular, with polar molecules such as water. The surface species that result from this interaction change the oxide electronic structure and chemical reactivity in applications such as photoelectrochemistry but are challenging to probe experimentally. Here, we report a detailed study of the surface chemistry and electronic structure of the perovskite LaFeO 3 in humid conditions using ambient-pressure X-ray photoelectron spectroscopy. In comparing the two possible terminations of the polar (001)-oriented surface, we find that the LaO-terminated surface is more reactive toward water, forming hydroxyl species and adsorbing molecularmore » water at lower relative humidity than its FeO 2-terminated counterpart. But, the FeO 2-terminated surface forms more hydroxyl species during water adsorption at higher humidity, suggesting that adsorbate–adsorbate interactions may impact reactivity. These results demonstrate how the termination of a complex oxide can dramatically impact its reactivity, providing insight that can aid in the design of catalyst materials.« less

Aquatic adaptations in the nose of carnivorans: evidence from the turbinates

PubMed Central

Van Valkenburgh, Blaire; Curtis, Abigail; Samuels, Joshua X; Bird, Deborah; Fulkerson, Brian; Meachen-Samuels, Julie; Slater, Graham J

2011-01-01

Inside the mammalian nose lies a labyrinth of bony plates covered in epithelium collectively known as turbinates. Respiratory turbinates lie anteriorly and aid in heat and water conservation, while more posterior olfactory turbinates function in olfaction. Previous observations on a few carnivorans revealed that aquatic species have relatively large, complex respiratory turbinates and greatly reduced olfactory turbinates compared with terrestrial species. Body heat is lost more quickly in water than air and increased respiratory surface area likely evolved to minimize heat loss. At the same time, olfactory surface area probably diminished due to a decreased reliance on olfaction when foraging under water. To explore how widespread these adaptations are, we documented scaling of respiratory and olfactory turbinate surface area with body size in a variety of terrestrial, freshwater, and marine carnivorans, including pinnipeds, mustelids, ursids, and procyonids. Surface areas were estimated from high-resolution CT scans of dry skulls, a novel approach that enabled a greater sampling of taxa than is practical with fresh heads. Total turbinate, respiratory, and olfactory surface areas correlate well with body size (r2 ≥ 0.7), and are relatively smaller in larger species. Relative to body mass or skull length, aquatic species have significantly less olfactory surface area than terrestrial species. Furthermore, the ratio of olfactory to respiratory surface area is associated with habitat. Using phylogenetic comparative methods, we found strong support for convergence on 1 : 3 proportions in aquatic taxa and near the inverse in terrestrial taxa, indicating that aquatic mustelids and pinnipeds independently acquired similar proportions of olfactory to respiratory turbinates. Constraints on turbinate surface area in the nasal chamber may result in a trade-off between respiratory and olfactory function in aquatic mammals. PMID:21198587

Distributional pattern of planktonic foraminifers and pteropods in surface waters and top core sediments of the Red Sea, and adjacent areas controlled by the monsoonal regime and other ecological factors

NASA Astrophysics Data System (ADS)

Auras-Schudnagies, Anabelle; Kroon, Dick; Ganssen, Gerald; Hemleben, Christoph; Van Hinte, Jan E.

1989-10-01

Living planktonic foraminiferal and pteropod distribution patterns in the western Arabian Sea, Gulf of Aden and Red Sea, collected during two summer cruises (1984, 1985), reflect the hydrographical system that is mainly controlled by a combination of monsoonal winds and evaporation rates. Spinose species constitute the majority of the planktonic foraminiferal assemblages in the Red Sea during both monsoonal seasons. The non-spinose species Globorotalia menardii, Neogloboquadrina dutertrei and Pulleniatina obliquiloculata, which are always abundant in the Arabian Sea, are present only during winter inflow. The intensity and duration of these inflowing surface currents control their distribution pattern. Stable oxygen isotope ratios show that G. menardii survives but ceases to grow north of Bab el Mandeb, while N. dutertrei continues to grow. Trends in the foraminiferal distribution in surface waters compare well with those of the sea floor, as far as larger specimens (>250 μm) are concerned, but differ for the small ones. Surface distribution patterns of small-sized specimens and juvenile/neanic stages of large-sized fully grown species do not correspond to those in the core top samples. The distribution pattern of living pteropods in the Red Sea is closely related to distinct water masses and corresponds to the distribution in top core sediments. Pteropods are absent in the sediments of the Gulf of Aden and the western Arabian Sea due to dissolution. Peak abundances of various pteropods and foraminifers indicate the presence of local upwelling processes in the Bab el Mandeb area. Determining these dynamics allows for the reconstruction of ancient oceanic environments and climatic interactions in the area.

Soot Surface Oxidation in Laminar Hydrocarbon/Air Diffusion Flames at Atmospheric Pressure. Appendix I

NASA Technical Reports Server (NTRS)

Xu, F.; El-Leathy, A. M.; Kim, C. H.; Faeth, G. M.; Yuan, Z.-G. (Technical Monitor); Urban, D. L. (Technical Monitor); Yuan, Z.-G. (Technical Monitor)

2003-01-01

Soot surface oxidation was studied experimentally in laminar hydrocarbon/air diffusion flames at atmospheric pressure. Measurements were carried out along the axes of round fuel jets burning in coflowing dry air considering acetylene-nitrogen, ethylene, propyiene-nitrogen, propane and acetylene-benzene-nitrogen in the fuel stream. Measurements were limited to the initial stages of soot oxidation (carbon consumption less than 70%) where soot oxidation occurs at the surface of primary soot particles. The following properties were measured as a function of distance above the burner exit: soot concentrations by deconvoluted laser extinction, soot temperatures by deconvoluted multiline emission, soot structure by thermophoretic sampling and analysis using Transmission Electron Microscopy (TEM), concentrations of major stable gas species (N2, H2O, H2, O2, CO, CO2, CH4, C2H2, C2H6, C3H6, C3H8, and C6H6) by sampling and gas chromatography, concentrations of some radical species (H, OH, O) by deconvoluted Li/LiOH atomic absorption and flow velocities by laser velocimetry. For present test conditions, it was found that soot surface oxidation rates were not affected by fuel type, that direct rates of soot surface oxidation by O2 estimated from Nagle and Strickland-Constable (1962) were small compared to observed soot surface oxidation rates because soot surface oxidation was completed near the flame sheet where O2 concentrations were less than 3% by volume, and that soot surface oxidation rates were described by the OH soot surface oxidation mechanism with a collision efficiency of 0.14 and an uncertainty (95% confidence) of +/- 0.04 when allowing for direct soot surface oxidation by O2, which is in reasonably good agreement with earlier observations of soot surface oxidation rates in both premixed and diffusion flames at atmospheric pressure.

GEOMETRIC, VOLUMETRIC, COLOUR AND FRICTIONAL PROPERTIES OF SELECTED SALVIA SPECIES OF TURKEY.

PubMed

Bayram, Mustafa; Altuntas, Ebubekir; Yilar, Melih

2017-01-01

Salvia seeds are promite to dietary and healthy oils because they contain essential fatty acids. Salvia seeds frequently produce mucilage on soaking, and this mucilage is used for the treatment of eye diseases in eastern countries. Salvia species studied for medicine, food and cosmetics, have the potential to be used in the various fields. In the present study, selected engineering (geometrical, volumetrical, colour and frictional) properties of 6 Salvia species seeds were determined and compared. This study was performed on selected engineering properties of seeds of 6 Salvia species ( Salvia viridis L., Salvia aethiopis L., Salvia cryptantha Montbert & Aucher ex Benthan., Salvia tomentosa Mill ., Salvia sclarea L., Salvia virgata Jacq.,) cultivated in Turkey. Plants were collected during the vegetation in 2012-2013 (May-Agust). The seeds were cleaned from foreign matter, dirt and broken seeds manually. The average length, width and thickness were found in the range of 2.61 to 3.53 mm, 1.59 to 2.92 mm and 1.14 to 2.52 mm, respectively. Salvia viridis L. specie had the lowest geometric mean diameter and surface area, whereas Salvia cryptantha L. had the least values among these 6 Salvia species for these properties. The bulk density, true density and the porosity were between 296.83 and 702.80 kg m -3 , 285.69 and 718.08 kg m -3 , 10.27 and 44.05%, respectively. The volume of unit seed and sphericity ranged between 2.56 and 13.64 mm 3 , 62.90 and 90.40%, respectively. The coefficient of friction of salvia species were largely influenced by the friction surfaces studied, and highest values were found for polywood in the Salvia crytantha L.. In the study, the static friction coefficient and the angle of repose of salvia species changed from 0.477 to 0.955, and from 14.09 to 23.57°, respectively. Determination of geometric, volumetric, colour and frictional properties of Salvia spp. seeds may increase their economic value.

Intraparticle reduction of arsenite (As(III)) by nanoscale zerovalent iron (nZVI) investigated with In Situ X-ray absorption spectroscopy.

PubMed

Yan, Weile; Vasic, Relja; Frenkel, Anatoly I; Koel, Bruce E

2012-07-03

While a high efficiency of contaminant removal by nanoscale zerovalent iron (nZVI) has often been reported for several contaminants of great concern, including aqueous arsenic species, the transformations and translocation of contaminants at and within the nanoparticles are not clearly understood. By analysis using in situ time-dependent X-ray absorption spectroscopy (XAS) of the arsenic core level for nZVI in anoxic As(III) solutions, we have observed that As(III) species underwent two stages of transformation upon adsorption at the nZVI surface. The first stage corresponds to breaking of As-O bonds at the particle surface, and the second stage involves further reduction and diffusion of arsenic across the thin oxide layer enclosing the nanoparticles, which results in arsenic forming an intermetallic phase with the Fe(0) core. Extended X-ray absorption fine-structure (EXAFS) data from experiments conducted at different iron/arsenic ratios indicate that the reduced arsenic species tend to be enriched at the surface of the Fe(0) core region and had limited mobility into the interior of the metal core within the experimental time frame (up to 22 h). Therefore, there was an accumulation of partially reduced arsenic at the Fe(0)/oxide interface when a relatively large arsenic content was present in the solid phase. These results illuminate the role of intraparticle diffusion and reduction in affecting the chemical state and spatial distribution of arsenic in nZVI materials.

A Ploidy-Sensitive Mechanism Regulates Aperture Formation on the Arabidopsis Pollen Surface and Guides Localization of the Aperture Factor INP1

PubMed Central

Reeder, Sarah H.; Lee, Byung Ha; Fox, Ronald; Dobritsa, Anna A.

2016-01-01

Pollen presents a powerful model for studying mechanisms of precise formation and deposition of extracellular structures. Deposition of the pollen wall exine leads to the generation of species-specific patterns on pollen surface. In most species, exine does not develop uniformly across the pollen surface, resulting in the formation of apertures–openings in the exine that are species-specific in number, morphology and location. A long time ago, it was proposed that number and positions of apertures might be determined by the geometry of tetrads of microspores–the precursors of pollen grains arising via meiotic cytokinesis, and by the number of last-contact points between sister microspores. We have tested this model by characterizing Arabidopsis mutants with ectopic apertures and/or abnormal geometry of meiotic products. Here we demonstrate that contact points per se do not act as aperture number determinants and that a correct geometric conformation of a tetrad is neither necessary nor sufficient to generate a correct number of apertures. A mechanism sensitive to pollen ploidy, however, is very important for aperture number and positions and for guiding the aperture factor INP1 to future aperture sites. In the mutants with ectopic apertures, the number and positions of INP1 localization sites change depending on ploidy or ploidy-related cell size and not on INP1 levels, suggesting that sites for aperture formation are specified before INP1 is brought to them. PMID:27177036

Surface composition of Europa based on VLT observations

NASA Astrophysics Data System (ADS)

Ligier, N.; Poulet, F.; Carter, J.

2016-12-01

Jupiter's moon Europa may harbor a global salty ocean under an 80-170 km thick outer layer consisting of an icy crust (Anderson et al. 1998). Meanwhile, the 10-50 My old surface, dated by cratering rates (Pappalardo et al. 1999) implies rapid surface recycling and reprocessing that could result in tectonic activity (Kattenhorn et al. 2014) and plumes (Roth et al. 2014). The surface could thus exhibit fingerprints of chemical species, as minerals characteristics of an ocean-mantle interaction and/or organics of exobiological interest, directly originating from the subglacial ocean. In order to re-investigate the composition of Europa's surface, a global mapping campaign of the satellite was performed with the near-infrared integral field spectrograph SINFONI on the Very Large Telescope (VLT) in Chile. The high spectral binning of this instrument (0.5 nm) and large signal noise ratio in comparison to previous observations are adequate to detect sharp absorptions in the wavelength range 1.45-2.45 μm. In addition, the spatially resolved spectra we obtained over five epochs nearly cover the entire surface of Europa with a pixel scale of 12.5 by 25 m.a.s ( 35 by 70 km on Europa's surface), thus permitting a global scale study. Several icy and non-icy compounds were detected and mapped at <100 km resolution. They are unevenly distributed on the moon's surface. Amorphous and crystalline water ice are both present and, in spite of a particularly strong amorphization process likely engendered by the Io plasma torus, the crystalline form is found to be approximately twice as abundant as the amorphous ice based on the analysis of the 1.65 μm band. If the surface is dominated by small and mid-sized water ice grains (25-200 μm), crystalline water-ice grains exhibit spatial inhomogeneities in their distribution. The sulfuric acid hydrate distribution exhibits the typical "bullseye" feature on the trailing hemisphere. The presence of Mg-bearing chlorinated salts (chloride, chlorate, and perchlorate) is supported by linear spectral modeling of the data, while the presence of sulfate salts is challenged. The distribution of some of these species is inconsistent with exogenic processes mainly impacting the trailing orbital hemisphere. These species may be traces of endogenous processes occurring on Europa.

Modeling Cl2/O2/Ar inductively coupled plasmas used for silicon etching: effects of SiO2 chamber wall coating

NASA Astrophysics Data System (ADS)

Tinck, S.; Boullart, W.; Bogaerts, A.

2011-08-01

In this paper, simulations are performed to gain a better insight into the properties of a Cl2/Ar plasma, with and without O2, during plasma etching of Si. Both plasma and surface properties are calculated in a self-consistent manner. Special attention is paid to the behavior of etch products coming from the wafer or the walls, and how the chamber walls can affect the plasma and the resulting etch process. Two modeling cases are considered. In the first case, the reactor walls are defined as clean (Al2O3), whereas in the second case a SiO2 coating is introduced on the reactor walls before the etching process, so that oxygen will be sputtered from the walls and introduced into the plasma. For this reason, a detailed reaction set is presented for a Cl2/O2/Ar plasma containing etched species, as well as an extensive reaction set for surface processes, including physical and chemical sputtering, chemical etching and deposition processes. Density and flux profiles of various species are presented for a better understanding of the bulk plasma during the etching process. Detailed information is also given on the composition of the surfaces at various locations of the reactor, on the etch products in the plasma and on the surface loss probabilities of the plasma species at the walls, with different compositions. It is found that in the clean chamber, walls are mostly chlorinated (Al2Cl3), with a thin layer of etch products residing on the wall. In the coated chamber, an oxy-chloride layer is grown on the walls for a few nanometers during the etching process. The Cl atom wall loss probability is found to decrease significantly in the coated chamber, hence increasing the etch rate. SiCl2, SiCl4 and SiCl3 are found to be the main etch products in the plasma, with the fraction of SiCl2 being always slightly higher. The simulation results compare well with experimental data available from the literature.

Exploring the Role of Habitat on the Wettability of Cicada Wings.

PubMed

Oh, Junho; Dana, Catherine E; Hong, Sungmin; Román, Jessica K; Jo, Kyoo Dong; Hong, Je Won; Nguyen, Jonah; Cropek, Donald M; Alleyne, Marianne; Miljkovic, Nenad

2017-08-16

Evolutionary pressure has pushed many extant species to develop micro/nanostructures that can significantly affect wettability and enable functionalities such as droplet jumping, self-cleaning, antifogging, antimicrobial, and antireflectivity. In particular, significant effort is underway to understand the insect wing surface structure to establish rational design tools for the development of novel engineered materials. Most studies, however, have focused on superhydrophobic wings obtained from a single insect species, in particular, the Psaltoda claripennis cicada. Here, we investigate the relationship between the spatially dependent wing wettability, topology, and droplet jumping behavior of multiple cicada species and their habitat, lifecycle, and interspecies relatedness. We focus on cicada wings of four different species: Neotibicen pruinosus, N. tibicen, Megatibicen dorsatus, and Magicicada septendecim and take a comparative approach. Using spatially resolved microgoniometry, scanning electron microscopy, atomic force microscopy, and high speed optical microscopy, we show that within cicada species, the wettability of wings is spatially homogeneous across wing cells. All four species were shown to have truncated conical pillars with widely varying length scales ranging from 50 to 400 nm in height. Comparison of the wettability revealed three cicada species with wings that are superhydrophobic (>150°) with low contact angle hysteresis (<5°), resulting in stable droplet jumping behavior. The fourth, more distantly related species (Ma. septendecim) showed only moderate hydrophobic behavior, eliminating some of the beneficial surface functional aspects for this cicada. Correlation between cicada habitat and wing wettability yielded little connection as wetter, swampy environments do not necessarily equate to higher measured wing hydrophobicity. The results, however, do point to species relatedness and reproductive strategy as a closer proxy for predicting wettability and surface structure and resultant enhanced wing surface functionality. This work not only elucidates the differences between inter- and intraspecies cicada wing topology, wettability, and water shedding behavior but also enables the development of rational design tools for the manufacture of artificial surfaces for energy and water applications.

Decreasing Abundance, Increasing Diversity and Changing Structure of the Wild Bee Community (Hymenoptera: Anthophila) along an Urbanization Gradient

PubMed Central

Fortel, Laura; Henry, Mickaël; Guilbaud, Laurent; Guirao, Anne Laure; Kuhlmann, Michael; Mouret, Hugues; Rollin, Orianne; Vaissière, Bernard E.

2014-01-01

Background Wild bees are important pollinators that have declined in diversity and abundance during the last decades. Habitat destruction and fragmentation associated with urbanization are reported as part of the main causes of this decline. Urbanization involves dramatic changes of the landscape, increasing the proportion of impervious surface while decreasing that of green areas. Few studies have investigated the effects of urbanization on bee communities. We assessed changes in the abundance, species richness, and composition of wild bee community along an urbanization gradient. Methodology/Principal Findings Over two years and on a monthly basis, bees were sampled with colored pan traps and insect nets at 24 sites located along an urbanization gradient. Landscape structure within three different radii was measured at each study site. We captured 291 wild bee species. The abundance of wild bees was negatively correlated with the proportion of impervious surface, while species richness reached a maximum at an intermediate (50%) proportion of impervious surface. The structure of the community changed along the urbanization gradient with more parasitic species in sites with an intermediate proportion of impervious surface. There were also greater numbers of cavity-nesting species and long-tongued species in sites with intermediate or higher proportion of impervious surface. However, urbanization had no effect on the occurrence of species depending on their social behavior or body size. Conclusions/Significance We found nearly a third of the wild bee fauna known from France in our study sites. Indeed, urban areas supported a diverse bee community, but sites with an intermediate level of urbanization were the most speciose ones, including greater proportion of parasitic species. The presence of a diverse array of bee species even in the most urbanized area makes these pollinators worthy of being a flagship group to raise the awareness of urban citizens about biodiversity. PMID:25118722

Decreasing abundance, increasing diversity and changing structure of the wild bee community (Hymenoptera: Anthophila) along an urbanization gradient.

PubMed

Fortel, Laura; Henry, Mickaël; Guilbaud, Laurent; Guirao, Anne Laure; Kuhlmann, Michael; Mouret, Hugues; Rollin, Orianne; Vaissière, Bernard E

2014-01-01

Wild bees are important pollinators that have declined in diversity and abundance during the last decades. Habitat destruction and fragmentation associated with urbanization are reported as part of the main causes of this decline. Urbanization involves dramatic changes of the landscape, increasing the proportion of impervious surface while decreasing that of green areas. Few studies have investigated the effects of urbanization on bee communities. We assessed changes in the abundance, species richness, and composition of wild bee community along an urbanization gradient. Over two years and on a monthly basis, bees were sampled with colored pan traps and insect nets at 24 sites located along an urbanization gradient. Landscape structure within three different radii was measured at each study site. We captured 291 wild bee species. The abundance of wild bees was negatively correlated with the proportion of impervious surface, while species richness reached a maximum at an intermediate (50%) proportion of impervious surface. The structure of the community changed along the urbanization gradient with more parasitic species in sites with an intermediate proportion of impervious surface. There were also greater numbers of cavity-nesting species and long-tongued species in sites with intermediate or higher proportion of impervious surface. However, urbanization had no effect on the occurrence of species depending on their social behavior or body size. We found nearly a third of the wild bee fauna known from France in our study sites. Indeed, urban areas supported a diverse bee community, but sites with an intermediate level of urbanization were the most speciose ones, including greater proportion of parasitic species. The presence of a diverse array of bee species even in the most urbanized area makes these pollinators worthy of being a flagship group to raise the awareness of urban citizens about biodiversity.

Background levels of some major, trace, and rare earth elements in indigenous plant species growing in Norway and the influence of soil acidification, soil parent material, and seasonal variation on these levels.

PubMed

Gjengedal, Elin; Martinsen, Thomas; Steinnes, Eiliv

2015-06-01

Baseline levels of 43 elements, including major, trace, and rare earth elements (REEs) in several native plant species growing in boreal and alpine areas, are presented. Focus is placed on species metal levels at different soil conditions, temporal variations in plant tissue metal concentrations, and interspecies variation in metal concentrations. Vegetation samples were collected at Sogndal, a pristine site in western Norway, and at Risdalsheia, an acidified site in southernmost Norway. Metal concentrations in the different species sampled in western Norway are compared with relevant literature data from Norway, Finland, and northwest Russia, assumed to represent natural conditions. Except for aluminium (Al) and macronutrients, the levels of metals were generally lower in western Norway than in southern Norway and may be considered close to natural background levels. In southern Norway, the levels of cadmium (Cd) and lead (Pb) in particular appear to be affected by air pollution, either by direct atmospheric supply or through soil acidification. Levels of some elements show considerable variability between as well as within plant species. Calcium (Ca), magnesium (Mg), and potassium (K) are higher in most species at Sogndal compared to Risdalsheia, despite increased extractable concentrations in surface soil in the south, probably attributed to different buffer mechanisms in surface soil. Antagonism on plant uptake is suggested between Ca, Mg, and K on one hand and Al on the other. Tolerance among calcifuges to acid conditions and a particular ability to detoxify or avoid uptake of Al ions are noticeable for Vaccinium vitis-idaea.

Integrated optical sensors for 2D spatial chemical mapping (Conference Presentation)

NASA Astrophysics Data System (ADS)

Flores, Raquel; Janeiro, Ricardo; Viegas, Jaime

2017-02-01

Sensors based on optical waveguides for chemical sensing have attracted increasing interest over the last two decades, fueled by potential applications in commercial lab-on-a-chip devices for medical and food safety industries. Even though the early studies were oriented for single-point detection, progress in device size reduction and device yield afforded by photonics foundries have opened the opportunity for distributed dynamic chemical sensing at the microscale. This will allow researchers to follow the dynamics of chemical species in field of microbiology, and microchemistry, with a complementary method to current technologies based on microfluorescence and hyperspectral imaging. The study of the chemical dynamics at the surface of photoelectrodes in water splitting cells are a good candidate to benefit from such optochemical sensing devices that includes a photonic integrated circuit (PIC) with multiple sensors for real-time detection and spatial mapping of chemical species. In this project, we present experimental results on a prototype integrated optical system for chemical mapping based on the interaction of cascaded resonant optical devices, spatially covered with chemically sensitive polymers and plasmon-enhanced nanostructured metal/metal-oxide claddings offering chemical selectivity in a pixelated surface. In order to achieve a compact footprint, the prototype is based in a silicon photonics platform. A discussion on the relative merits of a photonic platform based on large bandgap metal oxides and nitrides which have higher chemical resistance than silicon is also presented.

Biogeochemical cycling in the ocean. Part 1: Introduction to the effects of upwelling along the west coast of North America

NASA Technical Reports Server (NTRS)

Howe, John T.

1986-01-01

Coastal upwelling is examined as it relates to the cycling of chemical species in coastal waters along the west coast of North America. The temporal and spatial features of upwelling phenomena in the Eastern boundary regions of the North Pacific Ocean are presented and discussed in terms of upwelling episodes. Climate conditions affecting upwelling include: thermal effects, wind-induced shear stress which moves surface layers, and the curl of the wind stress vector which is thought to affect the extent and nature of upwelling and the formation of offshore convergent downwelling fronts. These effects and the interaction of sunlight and upwelled nutrients which result in a biological bloom in surface waters is modeled analytically. The roles of biological and chemical species, including the effects of predation, are discussed in that context, and relevant remote sensing and in situ observations are presented. Climatological, oceanographic, biological, physical, chemical events, and processes that pertain to biogeochemical cycling are presented and described by a set of partial differential equations. Simple preliminary results are obtained and are compared with data. Thus a fairly general framework has been laid where the many facets of biogeochemical cycling in coastal upwelled waters can be examined in their relationship to one another, and to the whole, to whatever level of detail or approximation is warranted or desired.

Real-time mapping of salt glands on the leaf surface of Cynodon dactylon L. using scanning electrochemical microscopy.

PubMed

Parthasarathy, Meera; Pemaiah, Brindha; Natesan, Ravichandran; Padmavathy, Saralla R; Pachiappan, Jayaraman

2015-02-01

Salt glands are specialized organelles present in the leaf tissues of halophytes, which impart salt-tolerance capability to the plant species. These glands are usually identified only by their morphology using conventional staining procedures coupled with optical microscopy. In this work, we have employed scanning electrochemical microscopy to identify the salt glands not only by their morphology but also by their salt excretion behavior. Bermuda grass (Cynodon dactylon L.) species was chosen for the study as they are known to be salt-tolerant and contain salt glands on leaf surfaces. Scanning electrochemical microscopy performed in sodium chloride medium in the presence and absence of potassium ferrocyanide as redox mediator, reveals the identity of salt glands. More insight into the ion expulsion behavior of these glands was obtained by mapping lateral and vertical variations in ion concentrations using surface impedance measurements which indicated five times higher resistance over the salt glands compared to the surrounding tissues and bulk solution. The protocol could be used to understand the developmental processes in plants grown in different soil/water conditions in order to improve salt tolerance of food crops by genetic engineering and hence improve their agricultural productivity.

Spin-driven structural effects in alkali doped (4)He clusters from quantum calculations.

PubMed

Bovino, S; Coccia, E; Bodo, E; Lopez-Durán, D; Gianturco, F A

2009-06-14

In this paper, we carry out variational Monte Carlo and diffusion Monte Carlo (DMC) calculations for Li(2)((1)Sigma(g) (+))((4)He)(N) and Li(2)((3)Sigma(u) (+))((4)He)(N) with N up to 30 and discuss in detail the results of our computations. After a comparison between our DMC energies with the "exact" discrete variable representation values for the species with one (4)He, in order to test the quality of our computations at 0 K, we analyze the structural features of the whole range of doped clusters. We find that both species reside on the droplet surface, but that their orientation is spin driven, i.e., the singlet molecule is perpendicular and the triplet one is parallel to the droplet's surface. We have also computed quantum vibrational relaxation rates for both dimers in collision with a single (4)He and we find them to differ by orders of magnitude at the estimated surface temperature. Our results therefore confirm the findings from a great number of experimental data present in the current literature and provide one of the first attempts at giving an accurate, fully quantum picture for the nanoscopic properties of alkali dimers in (4)He clusters.

Adsorption of Cr(III) on ozonised activated carbon. Importance of Cpi-cation interactions.

PubMed

Rivera-Utrilla, J; Sánchez-Polo, M

2003-08-01

The adsorption of Cr(III) in aqueous solution was investigated on a series of ozonised activated carbons, analysing the effect of oxygenated surface groups on the adsorption process. A study was carried out to determine the adsorption isotherms and the influence of the pH on the adsorption of this metal. The adsorption capacity and affinity of the adsorbent for Cr(III) increased with the increase in oxygenated acid groups on the surface of the activated carbon. These findings imply that electrostatic-type interactions predominate in the adsorption process, although the adsorption of Cr(III) on the original (basic) carbon indicates that other forces also participate in the adsorption process. Thus, the ionic exchange of protons in the -Cpi-H3O(+) interaction for Cr(III) accounts for the adsorption of cationic species in basic carbons with positive charge density. Study of the influence of pH on the adsorption of Cr(III) showed that, in each system, the maximum adsorption occurred when the charge of the carbon surface was opposite that of the species of Cr(III) present at the pH of the experiment. These results confirmed that electrostatic interactions predominate in the adsorption process.

Discrete bivariate population balance modelling of heteroaggregation processes.

PubMed

Rollié, Sascha; Briesen, Heiko; Sundmacher, Kai

2009-08-15

Heteroaggregation in binary particle mixtures was simulated with a discrete population balance model in terms of two internal coordinates describing the particle properties. The considered particle species are of different size and zeta-potential. Property space is reduced with a semi-heuristic approach to enable an efficient solution. Aggregation rates are based on deterministic models for Brownian motion and stability, under consideration of DLVO interaction potentials. A charge-balance kernel is presented, relating the electrostatic surface potential to the property space by a simple charge balance. Parameter sensitivity with respect to the fractal dimension, aggregate size, hydrodynamic correction, ionic strength and absolute particle concentration was assessed. Results were compared to simulations with the literature kernel based on geometric coverage effects for clusters with heterogeneous surface properties. In both cases electrostatic phenomena, which dominate the aggregation process, show identical trends: impeded cluster-cluster aggregation at low particle mixing ratio (1:1), restabilisation at high mixing ratios (100:1) and formation of complex clusters for intermediate ratios (10:1). The particle mixing ratio controls the surface coverage extent of the larger particle species. Simulation results are compared to experimental flow cytometric data and show very satisfactory agreement.

A Particle-In-Cell Gun Code for Surface-Converter H- Ion Source Modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chacon-Golcher, Edwin; Bowers, Kevin J.

2007-08-10

We present the current status of a particle-in-cell with Monte Carlo collisions (PIC-MCC) gun code under development at Los Alamos for the study of surface-converter H- ion sources. The program preserves a first-principles approach to a significant extent and simulates the production processes without ad hoc models within the plasma region. Some of its features include: solution of arbitrary electrostatic and magnetostatic fields in an axisymmetric (r,z) geometry to describe the self-consistent time evolution of a plasma; simulation of a multi-species (e-,H+,H{sub 2}{sup +},H{sub 3}{sup +},H-) plasma discharge from a neutral hydrogen gas and filament-originated seed electrons; full 2-dimensional (r,z)more » 3-velocity (vr,vz,v{phi}) dynamics for all species with exact conservation of the canonical angular momentum p{phi}; detailed collision physics between charged particles and neutrals and the ability to represent multiple smooth (not stair-stepped) electrodes of arbitrary shape and voltage whose surfaces may be secondary-particle emitters (H- and e-). The status of this development is discussed in terms of its physics content and current implementation details.« less

Study of sulfur bonding on gallium arsenide (100) surfaces using supercritical fluid extraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cabauy, P.; Darici, Y.; Furton, K.G.

1995-12-01

In the last decades Gallium Arsenide (GaAs) has been considered the semiconductor that will replace silicon because of its direct band gap and high electron mobility. Problems with GaAs Fermi level pinning has halted its widespread use in the electronics industry. The formation of oxides on GaAs results in a high density of surface states that effectively pin the surface Fermi level at the midgap. Studies on sulfur passivation have eliminated oxidation and virtually unpinned the Fermi level on the GaAs surface. This has given rise to interest in sulfur-GaAs bonds. In this presentation, we will discuss the types ofmore » sulfur bonds extracted from a sulfur passivated GaAs (100) using Supercritical Fluid (CO2) Extraction (SFE). SFE can be a valuable tool in the study of chemical speciations on semiconductor surfaces. The variables evaluated to effectively study the sulfur species from the GaAs surface include passivation techniques, supercritical fluid temperatures, densities, and extraction times.« less

Strong catalytic activity of iron nanoparticles on the surfaces of reduced olivine

NASA Astrophysics Data System (ADS)

Tucker, William C.; Quadery, Abrar H.; Schulte, Alfons; Blair, Richard G.; Kaden, William E.; Schelling, Patrick K.; Britt, Daniel T.

2018-01-01

It is demonstrated that olivine powders heated to subsolidus temperatures in reducing conditions can develop significant concentrations of 10-50 nm diameter Fe nanoparticles on grain surfaces and that these display strong catalytic activity not observed in powders without Fe nanoparticles. Reduced surfaces were exposed to NH3, CO, and H2, volatiles that may be present on the surfaces of comet and volatile-rich asteroids. In the case of NH3 exposure, rapid decomposition was observed. When exposed to a mixture of CO and H2, significant coking of the mineral surfaces occurred. Analysis of the mineral grains after reaction indicated primarily the presence of graphene or graphitic carbon. The results demonstrate that strong chemical activity can be expected at powders that contain nanophase Fe particles. This suggests space-weathered mineral surfaces may play an important role in the synthesis and processing of organic species. This processing may be part of the weathering processes of volatile-rich but atmosphereless solar-system bodies.

Surface chemistry of carbon dioxide revisited

NASA Astrophysics Data System (ADS)

Taifan, William; Boily, Jean-François; Baltrusaitis, Jonas

2016-12-01

This review discusses modern developments in CO2 surface chemistry by focusing on the work published since the original review by H.J. Freund and M.W. Roberts two decades ago (Surface Science Reports 25 (1996) 225-273). It includes relevant fundamentals pertaining to the topics covered in that earlier review, such as conventional metal and metal oxide surfaces and CO2 interactions thereon. While UHV spectroscopy has routinely been applied for CO2 gas-solid interface analysis, the present work goes further by describing surface-CO2 interactions under elevated CO2 pressure on non-oxide surfaces, such as zeolites, sulfides, carbides and nitrides. Furthermore, it describes additional salient in situ techniques relevant to the resolution of the interfacial chemistry of CO2, notably infrared spectroscopy and state-of-the-art theoretical methods, currently used in the resolution of solid and soluble carbonate species in liquid-water vapor, liquid-solid and liquid-liquid interfaces. These techniques are directly relevant to fundamental, natural and technological settings, such as heterogeneous and environmental catalysis and CO2 sequestration.

Influence of nanoscale topology on bactericidal efficiency of black silicon surfaces

NASA Astrophysics Data System (ADS)

Linklater, Denver P.; Khuong Duy Nguyen, Huu; Bhadra, Chris M.; Juodkazis, Saulius; Ivanova, Elena P.

2017-06-01

The nanostructuring of materials to create bactericidal and antibiofouling surfaces presents an exciting alternative to common methods of preventing bacterial adhesion. The fabrication of synthetic bactericidal surfaces has been inspired by the anti-wetting and anti-biofouling properties of insect wings, and other topologies found in nature. Black silicon is one such synthetic surfaces which has established bactericidal properties. In this study we show that time-dependent plasma etching of silicon wafers using 15, 30, and 45 min etching intervals, is able to produce different surface geometries with linearly increasing heights of approximately 280, 430, and 610 nm, respectively. After incubation on these surfaces with Gram-positive Staphylococcus aureus and Gram-negative Pseudomonas aeruginosa bacterial cells it was established that smaller, more densely packed pillars exhibited the greatest bactericidal activity with 85% and 89% inactivation of bacterial cells, respectively. The decrease in the pillar heights, pillar cap diameter and inter-pillar spacing corresponded to a subsequent decrease in the number of attached cells for both bacterial species.

Spatiotemporal Analysis of Cryptosporidium Species/Genotypes and Relationships with Other Zoonotic Pathogens in Surface Water from Mixed-Use Watersheds

PubMed Central

Wilkes, Graham; Ruecker, Norma J.; Neumann, Norman F.; Gannon, Victor P. J.; Jokinen, Cassandra; Sunohara, Mark; Topp, Edward; Pintar, Katarina D. M.; Edge, Thomas A.

2013-01-01

Nearly 690 raw surface water samples were collected during a 6-year period from multiple watersheds in the South Nation River basin, Ontario, Canada. Cryptosporidium oocysts in water samples were enumerated, sequenced, and genotyped by detailed phylogenetic analysis. The resulting species and genotypes were assigned to broad, known host and human infection risk classes. Wildlife/unknown, livestock, avian, and human host classes occurred in 21, 13, 3, and <1% of sampled surface waters, respectively. Cryptosporidium andersoni was the most commonly detected livestock species, while muskrat I and II genotypes were the most dominant wildlife genotypes. The presence of Giardia spp., Salmonella spp., Campylobacter spp., and Escherichia coli O157:H7 was evaluated in all water samples. The greatest significant odds ratios (odds of pathogen presence when host class is present/odds of pathogen presence when host class is absent) for Giardia spp., Campylobacter spp., and Salmonella spp. in water were associated, respectively, with livestock (odds ratio of 3.1), avian (4.3), and livestock (9.3) host classes. Classification and regression tree analyses (CART) were used to group generalized host and human infection risk classes on the basis of a broad range of environmental and land use variables while tracking cooccurrence of zoonotic pathogens in these groupings. The occurrence of livestock-associated Cryptosporidium was most strongly related to agricultural water pollution in the fall (conditions also associated with elevated odds ratios of other zoonotic pathogens occurring in water in relation to all sampling conditions), whereas wildlife/unknown sources of Cryptosporidium were geospatially associated with smaller watercourses where urban/rural development was relatively lower. Conditions that support wildlife may not necessarily increase overall human infection risks associated with Cryptosporidium since most Cryptosporidium genotypes classed as wildlife in this study (e.g., muskrat I and II genotype) do not pose significant infection risks to humans. Consequently, from a human health perspective, land use practices in agricultural watersheds that create opportunities for wildlife to flourish should not be rejected solely on the basis of their potential to increase relative proportions of wildlife fecal contamination in surface water. The present study suggests that mitigating livestock fecal pollution in surface water in this region would likely reduce human infection risks associated with Cryptosporidium and other zoonotic pathogens. PMID:23124241

Warming off southwestern Japan linked to distributional shifts of subtidal canopy-forming seaweeds.

PubMed

Tanaka, Kouki; Taino, Seiya; Haraguchi, Hiroko; Prendergast, Gabrielle; Hiraoka, Masanori

2012-11-01

To assess distributional shifts of species in response to recent warming, historical distribution records are the most requisite information. The surface seawater temperature (SST) of Kochi Prefecture, southwestern Japan on the western North Pacific, has significantly risen, being warmed by the Kuroshio Current. Past distributional records of subtidal canopy-forming seaweeds (Laminariales and Fucales) exist at about 10-year intervals from the 1970s, along with detailed SST datasets at several sites along Kochi's >700 km coastline. In order to provide a clear picture of distributional shifts of coastal marine organisms in response to warming SST, we observed the present distribution of seaweeds and analyzed the SST datasets to estimate spatiotemporal SST trends in this coastal region. We present a large increase of 0.3°C/decade in the annual mean SST of this area over the past 40 years. Furthermore, a comparison of the previous and present distributions clearly showed the contraction of temperate species' distributional ranges and expansion of tropical species' distributional ranges in the seaweeds. Although the main temperate kelp Ecklonia (Laminariales) had expanded their distribution during periods of cooler SST, they subsequently declined as the SST warmed. Notably, the warmest SST of the 1997-98 El Niño Southern Oscillation event was the most likely cause of a widespread destruction of the kelp populations; no recovery was found even in the present survey at the formerly habitable sites where warm SSTs have been maintained. Temperate Sargassum spp. (Fucales) that dominated widely in the 1970s also declined in accordance with recent warming SSTs. In contrast, the tropical species, S. ilicifolium, has gradually expanded its distribution to become the most conspicuously dominant among the present observations. Thermal gradients, mainly driven by the warming Kuroshio Current, are presented as an explanation for the successive changes in both temperate and tropical species' distributions.

Evolutionary History and Conservation Status of Cave Crayfishes Along the Cumberland Plateau

NASA Astrophysics Data System (ADS)

Buhay, J. E.; Crandall, K. A.

2005-05-01

Obligate cave-dwelling crayfish species are found only in southeastern United States, Mexico, and Cuba. Most species are considered to be endangered because of surface pollution threats to groundwater and small geographic distributions. There are currently three subterranean species of the genus Orconectes found along the Cumberland Plateau, a worldwide hotspot of cave biodiversity. The objectives of my dissertation research are to: 1) delineate species' boundaries using molecular genetic data in a phylogenetic framework, 2) examine evolutionary history of each species using Nested Clade Analysis, and 3) assess conservation status of each species using measures of effective population size and genetic diversity. This research project has uncovered a new species of cave crayfish along the border of Tennessee and Kentucky, an area previously thought to have "intergrades" between two subspecies of O. australis. It appears that Cambarus gentryi, a surface-dwelling burrowing species, is the closest living ancestor to the cave Orconectes assemblage on the Plateau. The origin appears to be Eastern Kentucky, with range expansions occuring southward down the Plateau. Although controversial, these cave species exhibit high levels of genetic diversity, especially in comparison to surface-dwellers. Conservation efforts should focus on protecting `high-traffic' areas to maintain gene flow and prevent isolation.

Modeling the surface tension of complex, reactive organic-inorganic mixtures

NASA Astrophysics Data System (ADS)

Schwier, A. N.; Viglione, G. A.; Li, Z.; McNeill, V. F.

2013-01-01

Atmospheric aerosols can contain thousands of organic compounds which impact aerosol surface tension, affecting aerosol properties such as cloud condensation nuclei (CCN) ability. We present new experimental data for the surface tension of complex, reactive organic-inorganic aqueous mixtures mimicking tropospheric aerosols. Each solution contained 2-6 organic compounds, including methylglyoxal, glyoxal, formaldehyde, acetaldehyde, oxalic acid, succinic acid, leucine, alanine, glycine, and serine, with and without ammonium sulfate. We test two surface tension models and find that most reactive, complex, aqueous organic mixtures which do not contain salt are well-described by a weighted Szyszkowski-Langmuir (S-L) model which was first presented by Henning et al. (2005). Two approaches for modeling the effects of salt were tested: (1) the Tuckermann approach (an extension of the Henning model with an additional explicit salt term), and (2) a new implicit method proposed here which employs experimental surface tension data obtained for each organic species in the presence of salt used with the Henning model. We recommend the use of method (2) for surface tension modeling because the Henning model (using data obtained from organic-inorganic systems) and Tuckermann approach provide similar modeling fits and goodness of fit (χ2) values, yet the Henning model is a simpler and more physical approach to modeling the effects of salt, requiring less empirically determined parameters.

[Spatial pattern of land surface dead combustible fuel load in Huzhong forest area in Great Xing'an Mountains].

PubMed

Liu, Zhi-Hua; Chang, Yu; Chen, Hong-Wei; Zhou, Rui; Jing, Guo-Zhi; Zhang, Hong-Xin; Zhang, Chang-Meng

2008-03-01

By using geo-statistics and based on time-lag classification standard, a comparative study was made on the land surface dead combustible fuels in Huzhong forest area in Great Xing'an Mountains. The results indicated that the first level land surface dead combustible fuel, i. e., 1 h time-lag dead fuel, presented stronger spatial auto-correlation, with an average of 762.35 g x m(-2) and contributing to 55.54% of the total load. Its determining factors were species composition and stand age. The second and third levels land surface dead combustible fuel, i. e., 10 h and 100 h time-lag dead fuels, had a sum of 610.26 g x m(-2), and presented weaker spatial auto-correlation than 1 h time-lag dead fuel. Their determining factor was the disturbance history of forest stand. The complexity and heterogeneity of the factors determining the quality and quantity of forest land surface dead combustible fuels were the main reasons for the relatively inaccurate interpolation. However, the utilization of field survey data coupled with geo-statistics could easily and accurately interpolate the spatial pattern of forest land surface dead combustible fuel loads, and indirectly provide a practical basis for forest management.

Two new species of Kalophrynus Tschudi, 1838 (Anura: Microhylidae) from the Annamite mountains in southern Vietnam.

PubMed

Vassilieva, Anna B; Galoyan, Eduard A; Gogoleva, Svetlana S; Poyarkov, Nikolay A

2014-05-20

We describe two new mountain-dwelling microhylid species of the genus Kalophrynus from the southern part of the Annamite Mountains in Vietnam. The two new species differ from all known congeners in morphological characters and mtDNA; phylogenetically, they form a sister clade to the large-bodied K. interlineatus (1009 bp, 16S rRNA gene, mtDNA). Both species share the following characteristics: snout pointed in dorsal and lateral views, slightly sloping in profile; tympanum distinct, smaller than eye in diameter; toe webbing moderate; outer metatarsal tubercle present; light dorsolateral line absent. Kalophrynus cryptophonus sp. nov. from Loc Bao, Lam Dong Province is a small-sized species distinguishing from its congeners by a combination of: SVL 27.9-30.4 mm in males, 23.4 mm in female; canthus rostralis indistinct; males with large sharp conical spines on the skin covering mandible margins and finely asperous nuptial pads on the dorsal surface of fingers I-III; dark ocelli in the inguinal region usually present, small, without a light border; anterior palatal dermal ridge short, restricted to medial part of palate. Kalophrynus honbaensis sp. nov. from Hon Ba, Khanh Hoa Province is a medium-sized Kalophrynus, distinguishing from its congeners by a combination of: SVL 26.7-36.8 mm in males; canthus rostralis distinct; males without distinguishable spines on the mandible margins nor the nuptial pads; dark ocelli in the inguinal region present, large, without a distinct light border, anterior palatal dermal ridge developed, parallel to posterior one. Kalophrynus cryptophonus sp. nov. reproduces in hollow bamboo stems; we describe larval morphology and bioacoustics of this species in relation to phytotelm breeding. A review of the distribution of the genus Kalophrynus in Indochina is provided.

Quantification of air plasma chemistry for surface disinfection

NASA Astrophysics Data System (ADS)

Pavlovich, Matthew J.; Clark, Douglas S.; Graves, David B.

2014-12-01

Atmospheric-pressure air plasmas, created by a variety of discharges, are promising sources of reactive species for the emerging field of plasma biotechnology because of their convenience and ability to operate at ambient conditions. One biological application of ambient-air plasma is microbial disinfection, and the ability of air plasmas to decontaminate both solid surfaces and liquid volumes has been thoroughly established in the literature. However, the mechanism of disinfection and which reactive species most strongly correlate with antimicrobial effects are still not well understood. We describe quantitative gas-phase measurements of plasma chemistry via infrared spectroscopy in confined volumes, focusing on air plasma generated via surface micro-discharge (SMD). Previously, it has been shown that gaseous chemistry is highly sensitive to operating conditions, and the measurements we describe here extend those findings. We quantify the gaseous concentrations of ozone (O3) and nitrogen oxides (NO and NO2, or NOx) throughout the established ‘regimes’ for SMD air plasma chemistry: the low-power, ozone-dominated mode; the high-power, nitrogen oxides-dominated mode; and the intermediate, unstable transition region. The results presented here are in good agreement with previously published experimental studies of aqueous chemistry and parameterized models of gaseous chemistry. The principal finding of the present study is the correlation of bacterial inactivation on dry surfaces with gaseous chemistry across these time and power regimes. Bacterial decontamination is most effective in ‘NOx mode’ and less effective in ‘ozone mode’, with the weakest antibacterial effects in the transition region. Our results underscore the dynamic nature of air plasma chemistry and the importance of careful chemical characterization of plasma devices intended for biological applications.

Planktonic Foraminifera Study at Site ODP 999A (Caribbean Sea): Insights into Oceanic Exchange and Paleocirculation During the last 450 Kyrs.

NASA Astrophysics Data System (ADS)

Vautravers, M. J.; Spero, H. J.; Schmidt, M. W.

2004-12-01

A recent micro-palaeontological study of a core from the South Atlantic (Peeters et al., Nature. 430, 661, 2004) stresses the importance of the Agulhas leakage intensity as a key control on North Atlantic Thermohaline operation. Planktonic foraminifera counts were conducted on the Colombian Basin core ODP 999A (12° N, 74° W, 2878 m); results are presented on a SPECMAP-based age model (Schmidt et al., in prep 2004). At present both climate and surface circulation are driven by the motion of the Intertropical Convergence Zone (ITCZ), which governs dry/wet seasons and upwelling intensity. Caribbean surface water originates from both the south Atlantic, which re-circulates Indian Ocean water, and the north Atlantic subtropical gyre. Similarly the deep-water is a mixture of AAIW and UNADW, originating in the southern and northern hemispheres respectively. A CaCO3 preservation index, which is deduced from planktonic fragments and pteropod remains, is used to trace changes in the intermediate water mixture. This study confirms that the sediments are better preserved during glacial times. Furthermore, it shows that the sediments of MIS11 are intensely dissolved, suggesting a maximal contribution of AAIW. Over the last 450 kyr, we observe a decreasing contribution of the AAIW during both interglacial and glacial times. In addition, the Holocene appears unusual, with a low AAIW to UNADW ratio in comparison to previous warm intervals. An examination of the percentages of the surface Indo-Pacific species G. menardii seems to confirm part this result, identifying MIS11 as a time of maximal Indian-Atlantic exchange via the Agulhas 3valve2. It also confirms that during MIS2, 3 and 4, Caribbean surface waters were unusually unfavourable for this species and/or that the Agulhas connection was absent. The % of G. Hexagona, another Indo-Pacific species, which lives in deeper thermocline waters, peaks during MIS11, MIS9e, MIS7c and MIS5e but is absent during the Holocene and MIS7e. This observation suggests a slightly different scenario for the intermediate water flowing through the 3valve2. This confirms the peculiarity of the Holocene as was found on the basis of benthic \\delta13C measurements in the North Atlantic (Raymo et al., Paleoceanography. 19, PA2008, 2004). Finally, on the basis of the species mentioned above in the Caribbean Sea we cannot find evidence of enhanced exchange between the Indian and the Atlantic at the end of the past five glacial as found in the Agulhas area. This disagreement and the factors controlling the late reappearance of these species in the Caribbean Sea need further investigation.

Harnessing the self-harvesting capability of benthic cyanobacteria for use in benthic photobioreactors

PubMed Central

2011-01-01

Benthic species of algae and cyanobacteria (i.e., those that grow on surfaces), may provide potential advantages over planktonic species for some commercial-scale biotechnological applications. A multitude of different designs of photobioreactor (PBR) are available for growing planktonic species but to date there has been little research on PBR for benthic algae or cyanobacteria. One notable advantage of some benthic cyanobacterial species is that during their growth cycle they become positively buoyant, detach from the growth surface and form floating mats. This 'self-harvesting' capability could be advantageous in commercial PBRs as it would greatly reduce dewatering costs. In this study we compared the growth rates and efficiency of 'self-harvesting' among three species of benthic cyanobacteria; Phormidium autumnale; Phormidium murrayi and Planktothrix sp.. Phormidium autumnale produced the greatest biomass and formed cohesive mats once detached. Using this strain and an optimised MLA media, a variety of geometries of benthic PBRs (bPBRs) were trialed. The geometry and composition of growth surface had a marked effect on cyanobacterial growth. The highest biomass was achieved in a bPBR comprising of a vertical polyethylene bag with loops of silicone tubing to provide additional growth surfaces. The productivity achieved in this bPBR was a similar order of magnitude as planktonic species, with the additional advantage that towards the end of the exponential phase the bulk of the biomass detached forming a dense mat at the surface of the medium. PMID:21906375

Dynamics of phase separation of binary fluids

NASA Technical Reports Server (NTRS)

Ma, Wen-Jong; Maritan, Amos; Banavar, Jayanth R.; Koplik, Joel

1992-01-01

The results of molecular-dynamics studies of surface-tension-dominated spinodal decomposition of initially well-mixed binary fluids in the absence and presence of gravity are presented. The growth exponent for the domain size and the decay exponent of the potential energy of interaction between the two species with time are found to be 0.6 +/- 0.1, inconsistent with scaling arguments based on dimensional analysis.

Mars Oxidant and Radical Detector

NASA Technical Reports Server (NTRS)

Yen, A. S.; Kim, S. S.

2003-01-01

The Mars Oxidant and Radical Detector is an instrument designed to characterize the reactive nature of the martian surface environment. Using Electron Paramagnetic Resonance (EPR) techniques, this instrument can detect, identify, and quantify radical species in soil samples, including those inferred to be present by the Viking experiments. This instrument is currently funded by the Mars Instrument Development Program and is compatible with the Mars Science Laboratory mission.

Microwave plasma assisted supersonic gas jet deposition of thin film materials

DOEpatents

Schmitt, III, Jerome J.; Halpern, Bret L.

1993-01-01

An apparatus for fabricating thin film materials utilizing high speed gas dynamics relies on supersonic free jets of carrier gas to transport depositing vapor species generated in a microwave discharge to the surface of a prepared substrate where the vapor deposits to form a thin film. The present invention generates high rates of deposition and thin films of unforeseen high quality at low temperatures.

Chronic TiO2 nanoparticle exposure to a benthic organism, Hyalella azteca: Impact of solar UV radiation and material surface coatings on toxicity

EPA Science Inventory

The present study examined the chronic toxicity of TiO2 nanoparticles (nano-TiO2) to a representative benthic species, Hyalella azteca, using an industry standard, P25, and a coated nano-TiO2 used in commercial products. There is limited information on the chronic effects of nano...

Molar crown and root size relationship in anthropoid primates.

PubMed

Kupczik, Kornelius; Olejniczak, Anthony J; Skinner, Matthew M; Hublin, Jean-Jacques

2009-01-01

Mandibular corpus form is thought to reflect masticatory function and the size of the dentition, but there is no universal association between crown dimensions and corpus size across anthropoids. Previous research was based on the assumption that crown size is an appropriate proxy for overall tooth size, but this hypothesis remains largely untested. This study assesses the relationship between the volume and surface area of molar crowns and roots by examining two main hypotheses: (1) crown size correlates significantly with root size, and (2) the proportion of root-to-crown surface area is related to dietary proclivity. Permanent M2s (n=58) representing 19 anthropoid species were CT scanned and the volume and surface area of the crown and root were measured. Interspecific correlation and regression analyses reveal significant isometric relationships between crown and root volume and a positive allometric relationship between root and crown surface area (i.e. as crown surface area increases, root surface area becomes disproportionately greater). Intraspecifically, crown and root surface area correlate significantly in some species where such analyses were possible. In general, hard object feeders exhibit relatively larger root surface area per unit crown surface area compared to soft and tough object feeders. The results also show that despite differences in food specialization closely related species have similar root-to-crown surface area proportions, thus indicating a strong phylogenetic influence. Since it is possible that, at least in some species, crown and root size vary independently, future studies should elucidate the relationship between tooth root size and mandible form. Copyright (c) 2009 S. Karger AG, Basel.

Isotope separation by photochromatography

DOEpatents

Suslick, K.S.

1975-10-03

A photochromatographic method for isotope separation is described. An isotopically mixed molecular species is adsorbed on an adsorptive surface, and the adsorbed molecules are irradiated with radiation of a predetermined wavelength which will selectively excite desired isotopic species. Sufficient energy is transferred to the excited molecules to desorb them from the surface and thus separate them from the undesired isotopic species. The method is particularly applicable to the separation of hydrogen isotopes. (BLM)

Molecular Simulations of the Diffusion of Uranyl Carbonate Species in Nanosized Mineral Fractures

NASA Astrophysics Data System (ADS)

Kerisit, S.; Liu, C.

2010-12-01

Uranium is a major groundwater contaminant at uranium processing and mining sites as a result of intentional and accidental discharges of uranium-containing waste products into subsurface environments. Recent characterization has shown that uranium preferentially associates with intragrain and intra-aggregate domains in some of the uranium-contaminated sediments collected from the US Department of Energy Hanford Site [1, 2]. In these sediments, uranium existed as precipitated and/or adsorbed phases in grain micropores with nano- to microscale sizes. Desorption and diffusion characterization studies and continuum-scale modeling indicated that ion diffusion in the microfractures is a major mechanism that led to preferential uranium concentration in the microfracture regions and will control the future mobility of uranium in the subsurface sediments [1, 3-4]. However, the diffusion properties of uranyl species in the intragrain regions, especially at the solid-liquid interface, are still poorly understood. Therefore, a general aim of this work is to provide atomic-level insights into the contribution of microscopic surface effects to the slow diffusion process of uranyl species in porous media with nano- to microsized fractures. In this presentation, we will first present molecular dynamics (MD) simulations of feldspar-water interfaces to investigate their interfacial structure and dynamics and establish a theoretical framework for subsequent simulations of water and ion diffusion at these interfaces [5]. We will then report on MD simulations carried out to probe the effects of confinement and of the presence of the mineral surface on the diffusion of water and electrolyte ions in nanosized feldspar fractures [6]. Several properties of the mineral-water interface were varied, such as the fracture width, the ionic strength of the contacting solution, and the surface charge. Our calculations reveal a 2.0-2.5 nm interfacial region within which the diffusion properties of water and that of the electrolyte ions differ significantly from those in bulk aqueous solutions. We will then present MD simulations of the diffusion of a series of alkaline-earth uranyl carbonate species in aqueous solutions [7]. The MD simulations show that the alkaline-earth uranyl carbonate complexes have distinct water exchange dynamics, which could lead to different reactivities. Finally, we will present recent results on the diffusion and adsorption of uranyl carbonate species in intragrain micropores, modeled with the feldspar-water interfaces mentioned in the above, to help interpret the diffusion behavior of uranium in contaminated sediments. [1] Liu C. et al. Geochim. Cosmochim. Acta 68 4519 (2004) [2] McKinley J. P. et al. Geochim. Cosmochim. Acta 70 1873 (2006) [3] Liu C. et al. Water Resour. Res. 42 W12420 (2006) [4] Ilton E. S. et al. Environ. Sci. Technol. 42 1565 (2009) [5] Kerisit S. et al. Geochim. Cosmochim. Acta 72 1481 (2008) [6] Kerisit S. and Liu C. Environ. Sci. Technol. 43 777 (2009) [7] Kerisit S. and Liu C. Geochim. Cosmochim. Acta 74 4937 (2010)

Evolution of Active Sites in Pt-Based Nanoalloy Catalysts for the Oxidation of Carbonaceous Species by Combined in Situ Infrared Spectroscopy and Total X-ray Scattering.

PubMed

Petkov, Valeri; Maswadeh, Yazan; Lu, Aolin; Shan, Shiyao; Kareem, Haval; Zhao, Yinguang; Luo, Jin; Zhong, Chuan-Jian; Beyer, Kevin; Chapman, Karena

2018-04-04

We present results from combined in situ infrared spectroscopy and total X-ray scattering studies on the evolution of catalytically active sites in exemplary binary and ternary Pt-based nanoalloys during a sequence of CO oxidation-reactivation-CO oxidation reactions. We find that when within a particular compositional range, the fresh nanoalloys may exhibit high catalytic activity for low-temperature CO oxidation. Using surface-specific atomic pair distribution functions (PDFs) extracted from the in situ total X-ray scattering data, we find that, regardless of their chemical composition and initial catalytic activity, the fresh nanoalloys suffer a significant surface structural disorder during CO oxidation. Upon reactivation in oxygen atmosphere, the surface of used nanoalloy catalysts both partially oxidizes and orders. Remarkably, it largely retains its structural state when the nanoalloys are reused as CO oxidation catalysts. The seemingly inverse structural changes of studied nanoalloy catalysts occurring under CO oxidation and reactivation conditions affect the active sites on their surface significantly. In particular, through different mechanisms, both appear to reduce the CO binding strength to the nanoalloy's surface and thus increase the catalytic stability of the nanoalloys. The findings provide clues for further optimization of nanoalloy catalysts for the oxidation of carbonaceous species through optimizing their composition, activation, and reactivation. Besides, the findings demonstrate the usefulness of combined in situ infrared spectroscopy and total X-ray scattering coupled to surface-specific atomic PDF analysis to the ongoing effort to produce advanced catalysts for environmentally and technologically important applications.

Lactate signalling regulates fungal β-glucan masking and immune evasion

PubMed Central

Ballou, Elizabeth R.; Avelar, Gabriela M.; Childers, Delma S.; Mackie, Joanna; Bain, Judith M.; Wagener, Jeanette; Kastora, Stavroula L.; Panea, Mirela D.; Hardison, Sarah E.; Walker, Louise A.; Erwig, Lars P.; Munro, Carol A.; Gow, Neil A.R.; Brown, Gordon D.; MacCallum, Donna M.; Brown, Alistair J.P.

2017-01-01

Summary Paragraph As they proliferate, fungi expose antigens at their cell surface that are potent stimulators of the innate immune response, and yet the commensal fungus Candida albicans is able to colonize immuno-competent individuals. We show that C. albicans may evade immune detection by presenting a moving immunological target. We report that the exposure of β-glucan, a key Pathogen Associated Molecular Pattern (PAMP) located at the cell surface of C. albicans and other pathogenic Candida species, is modulated in response to changes in carbon source. Exposure to lactate induces β-glucan masking in C. albicans via a signaling pathway that has recruited an evolutionarily conserved receptor (Gpr1) and transcriptional factor (Crz1) from other well-characterized pathways. In response to lactate, these regulators control the expression of cell wall related genes that contribute to β-glucan masking. This represents the first description of active PAMP masking by a Candida species, a process that reduces the visibility of the fungus to the immune system. PMID:27941860

The oral bacterial microbiome of occlusal surfaces in children and its association with diet and caries.

PubMed

Ribeiro, Apoena Aguiar; Azcarate-Peril, Maria Andrea; Cadenas, Maria Belen; Butz, Natasha; Paster, Bruce J; Chen, Tsute; Bair, Eric; Arnold, Roland R

2017-01-01

Dental caries is the most prevalent disease in humans globally. Efforts to control it have been invigorated by an increasing knowledge of the oral microbiome composition. This study aimed to evaluate the bacterial diversity in occlusal biofilms and its relationship with clinical surface diagnosis and dietary habits. Anamneses were recorded from thirteen 12-year-old children. Biofilm samples collected from occlusal surfaces of 46 permanent second molars were analyzed by 16S rRNA amplicon sequencing combined with the BLASTN-based search algorithm for species identification. The overall mean decayed, missing and filled surfaces modified index [DMFSm Index, including active white spot lesions (AWSL)] value was 8.77±7.47. Biofilm communities were highly polymicrobial collectively, representing 10 bacterial phyla, 25 classes, 29 orders, 58 families, 107 genera, 723 species. Streptococcus sp_Oral_Taxon_065, Corynebacterium matruchotii, Actinomyces viscosus, Actinomyces sp_Oral_Taxon_175, Actinomyces sp_Oral_Taxon_178, Actinomyces sp_Oral_Taxon_877, Prevotella nigrescens, Dialister micraerophilus, Eubacterium_XI G 1 infirmum were more abundant among surfaces with AWSL, and Streptococcus gordonii, Streptococcus sp._Oral_Taxon_058, Enterobacter sp._str._638 Streptococcus australis, Yersinia mollaretii, Enterobacter cloacae, Streptococcus sp._Oral_Taxon_71, Streptococcus sp._Oral_Taxon_F11, Centipeda sp._Oral_Taxon_D18 were more abundant among sound surfaces. Streptococcus mutans was detected on all surfaces in all patients, while Streptococcus sobrinus was detected only in three patients (mean relative abundances 7.1% and 0.6%, respectively). Neither species differentiated healthy from diseased sites. Diets of nine of the subjects were scored as high in fermentable carbohydrates (≧2X/day between meals). A direct association between relative abundances of bacteria and carbohydrate consumption was observed among 18 species. High consumption of fermentable carbohydrates and sound surfaces were associated with a reduction in bacterial diversity. PCoA plots displayed differences in bacterial community profiles between sound and diseased surfaces. Our study showed that, in addition to mutans streptococci, other species may be associated with the initiation of dental caries on occlusal surfaces, and that biofilm diversity of tooth surfaces is influenced by carbohydrate consumption and a surface's health status.

A new genus of mellitid sand dollar (Echinoidea: Mellitidae) from the eastern Pacific coast of the Americas.

PubMed

Coppard, Simon E

2016-05-13

Lanthonia gen. nov. Coppard 2016 is a genus of clypeasteroid sand dollar whose members inhabit shallow, sandy waters from Mexico (including the Gulf of California) to Colombia in the tropical and subtropical eastern Pacific. Lanthonia includes Lanthonia longifissa (Michelin, 1858) and Lanthonia grantii (Mortensen, 1948), with L. longifissa hereby designated as the type species. Both L. longifissa and L. grantii were previously placed in the genus Mellita (L. Agassiz, 1841). However, levels of genetic divergence between a lineage containing L. longifissa and L. grantii and a lineage containing all other species of Mellita, including the type species M. quinquiesperforata (Leske, 1778), indicate genus level differentiation. The systematic interpretation of this group also supports the designation of this new genus as it allows the tree topology to be recovered from the nomenclature and clarifies the historical biogeography of these clades. This has resulted in members of both lineages today being sympatric in the eastern Pacific. Members of Lanthonia are morphologically differentiated from the type species of Mellita and all Pacific Mellita in having very narrow ambulacral regions between the food grooves and the ambulacral lunules on the oral surface, these being very broad in both M. quinquiesperforata and M. notabilis. The dentation of the bidentate pedicellariae also differentiate these genera, with small peripheral teeth present along the edge of the blade in species of Lanthonia and one to three enlarged intersecting teeth present distally in all species of Mellita.

Surface Complexation Modeling of Calcite Zeta Potential Measurement in Mixed Brines for Carbonate Wettability Characterization

NASA Astrophysics Data System (ADS)

Song, J.; Zeng, Y.; Biswal, S. L.; Hirasaki, G. J.

2017-12-01

We presents zeta potential measurements and surface complexation modeling (SCM) of synthetic calcite in various conditions. The systematic zeta potential measurement and the proposed SCM provide insight into the role of four potential determining cations (Mg2+, SO42- , Ca2+ and CO32-) and CO2 partial pressure in calcite surface charge formation and facilitate the revealing of calcite wettability alteration induced by brines with designed ionic composition ("smart water"). Brines with varying potential determining ions (PDI) concentration in two different CO2 partial pressure (PCO2) are investigated in experiments. Then, a double layer SCM is developed to model the zeta potential measurements. Moreover, we propose a definition for contribution of charged surface species and quantitatively analyze the variation of charged species contribution when changing brine composition. After showing our model can accurately predict calcite zeta potential in brines containing mixed PDIs, we apply it to predict zeta potential in ultra-low and pressurized CO2 environments for potential applications in carbonate enhanced oil recovery including miscible CO2 flooding and CO2 sequestration in carbonate reservoirs. Model prediction reveals that pure calcite surface will be positively charged in all investigated brines in pressurized CO2 environment (>1atm). Moreover, the sensitivity of calcite zeta potential to CO2 partial pressure in the various brine is found to be in the sequence of Na2CO3 > Na2SO4 > NaCl > MgCl2 > CaCl2 (Ionic strength=0.1M).

Determination of hydrogen abundance in selected lunar soils

NASA Technical Reports Server (NTRS)

Bustin, Roberta

1987-01-01

Hydrogen was implanted in lunar soil through solar wind activity. In order to determine the feasibility of utilizing this solar wind hydrogen, it is necessary to know not only hydrogen abundances in bulk soils from a variety of locations but also the distribution of hydrogen within a given soil. Hydrogen distribution in bulk soils, grain size separates, mineral types, and core samples was investigated. Hydrogen was found in all samples studied. The amount varied considerably, depending on soil maturity, mineral types present, grain size distribution, and depth. Hydrogen implantation is definitely a surface phenomenon. However, as constructional particles are formed, previously exposed surfaces become embedded within particles, causing an enrichment of hydrogen in these species. In view of possibly extracting the hydrogen for use on the lunar surface, it is encouraging to know that hydrogen is present to a considerable depth and not only in the upper few millimeters. Based on these preliminary studies, extraction of solar wind hydrogen from lunar soil appears feasible, particulary if some kind of grain size separation is possible.

Analytical solutions of the planar cyclic voltammetry process for two soluble species with equal diffusivities and fast electron transfer using the method of eigenfunction expansions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samin, Adib; Lahti, Erik; Zhang, Jinsuo, E-mail: zhang.3558@osu.edu

Cyclic voltammetry is a powerful tool that is used for characterizing electrochemical processes. Models of cyclic voltammetry take into account the mass transport of species and the kinetics at the electrode surface. Analytical solutions of these models are not well-known due to the complexity of the boundary conditions. In this study we present closed form analytical solutions of the planar voltammetry model for two soluble species with fast electron transfer and equal diffusivities using the eigenfunction expansion method. Our solution methodology does not incorporate Laplace transforms and yields good agreement with the numerical solution. This solution method can be extendedmore » to cases that are more general and may be useful for benchmarking purposes.« less

Trace gas exchanges and transports over the Amazonian rain forest

NASA Technical Reports Server (NTRS)

Garstang, Michael; Greco, Steve; Scala, John; Harriss, Robert; Browell, Edward; Sachse, Glenn; Simpson, Joanne; Tao, Wei-Kuo; Torres, Arnold

1986-01-01

Early results are presented from a program to model deep convective transport of chemical species by means of in situ data collection and numerical models. Data were acquired during the NASA GTE Amazon Boundary Layer Experiment in July-August 1985. Airborne instrumentation, including a UV-DIAL system, collected data on the O3, CO, NO, temperature and water vapor profiles from the surface to 400 mb altitude, while GOES imagery tracked convective clouds over the study area. A two-dimensional cloud model with small amplitude random temperature fluctuations at low levels, which simulated thermals, was used to describe the movements of the chemical species sensed in the convective atmosphere. The data was useful for evaluating the accuracy of the cloud model, which in turn was effective in describing the circulation of the chemical species.

Effect of Plant Species and Environmental Conditions on Ice Nucleation Activity of Pseudomonas syringae on Leaves.

PubMed

O'brien, R D; Lindow, S E

1988-09-01

Selected plant species and environmental conditions were investigated for their influences on expression of ice nucleation activity by 15 Pseudomonas syringae strains grown on plants in constant-temperature growth chamber studies. Ice nucleation frequencies (INFs), the fraction of cells that expressed ice nucleation at -5 or -9 degrees C, of individual strains varied greatly, both on plants and in culture. This suggests that the probability of frost injury, which is proportional to the number of ice nuclei on leaf surfaces, is strongly determined by the particular bacterial strains that are present on a leaf surface. The INFs of strains were generally higher when they were grown on plants than when they were grown in culture. In addition, INFs in culture did not correlate closely with INFs on plants, suggesting that frost injury prediction should be based on INF measurements of cells grown on plants rather than in culture. The relative INFs of individual strains varied with plant host and environment. However, none of seven plant species tested optimized the INFs of all 15 strains. Similarly, incubation for 48 h at near 100% relative humidity with short photoperiods did not always decrease the INF when compared with a 72 h, 40% relative humidity, long-photoperiod incubation. Pathogenic strains on susceptible hosts were not associated with higher or lower INFs relative to their INFs on nonsusceptible plant species. The ice nucleation activity of individual bacterial strains on plants therefore appears to be controlled by complex and interacting factors such as strain genotype, environment, and host plant species.

Isolation and Identification of the Indigenous Yeast Population during Spontaneous Fermentation of Isabella (Vitis labrusca L.) Grape Must.

PubMed

Raymond Eder, María L; Reynoso, Cristina; Lauret, Santiago C; Rosa, Alberto L

2017-01-01

Grape must harbors a complex community of yeast species responsible for spontaneous alcoholic fermentation. Although there are detailed studies on the microbiota of Vitis vinifera L. grapes, less is known about the diversity and behavior of yeast communities present on fermenting grape must from other species of Vitis . In this work, we used a culture-dependent method to study the identity and dynamics of the indigenous yeast population present during the spontaneous fermentation of Isabella ( Vitis labrusca L.) grape must. Alcoholic fermentation was conducted using standard enological practices, and the associated non- Saccharomyces and S. cerevisiae yeast community was analyzed using selective growth media and 5.8-ITS DNA sequencing. Candida californica, Candida hellenica, Starmerella bacillaris (synonym Candida zemplinina ), Hanseniaspora uvarum , and Hanseniaspora vineae were the main non- Saccharomyces species identified on Isabella fermenting must. Issatchenkia hanoiensis , a yeast species rarely found on Vitis vinifera L. grapes, was also recognized on Isabella grape must. Candida azymoides, Candida californica and Pichia cecembensis , identified in this work on Isabella fermenting must, have not previously been found on Vitis vinifera L. grape must. Interestingly, C. azymoides, I. hanoiensis and P. cecembensis have recently been isolated from the surface of Vitis labrusca L. grapes from vineyards in the Azores archipelago, suggesting that specific Vitis -yeast species associations are formed independently of geographic origin. We suggest that C. azymoides, C. californica , and P. cecembensis are yeast species preferentially associated with Vitis labrusca L. grapes. Specific biological interactions between grapevines and yeast species may underlie the assembly of differential Vitis -microbial communities.

Isolation and Identification of the Indigenous Yeast Population during Spontaneous Fermentation of Isabella (Vitis labrusca L.) Grape Must

PubMed Central

Raymond Eder, María L.; Reynoso, Cristina; Lauret, Santiago C.; Rosa, Alberto L.

2017-01-01

Grape must harbors a complex community of yeast species responsible for spontaneous alcoholic fermentation. Although there are detailed studies on the microbiota of Vitis vinifera L. grapes, less is known about the diversity and behavior of yeast communities present on fermenting grape must from other species of Vitis. In this work, we used a culture-dependent method to study the identity and dynamics of the indigenous yeast population present during the spontaneous fermentation of Isabella (Vitis labrusca L.) grape must. Alcoholic fermentation was conducted using standard enological practices, and the associated non-Saccharomyces and S. cerevisiae yeast community was analyzed using selective growth media and 5.8-ITS DNA sequencing. Candida californica, Candida hellenica, Starmerella bacillaris (synonym Candida zemplinina), Hanseniaspora uvarum, and Hanseniaspora vineae were the main non-Saccharomyces species identified on Isabella fermenting must. Issatchenkia hanoiensis, a yeast species rarely found on Vitis vinifera L. grapes, was also recognized on Isabella grape must. Candida azymoides, Candida californica and Pichia cecembensis, identified in this work on Isabella fermenting must, have not previously been found on Vitis vinifera L. grape must. Interestingly, C. azymoides, I. hanoiensis and P. cecembensis have recently been isolated from the surface of Vitis labrusca L. grapes from vineyards in the Azores archipelago, suggesting that specific Vitis-yeast species associations are formed independently of geographic origin. We suggest that C. azymoides, C. californica, and P. cecembensis are yeast species preferentially associated with Vitis labrusca L. grapes. Specific biological interactions between grapevines and yeast species may underlie the assembly of differential Vitis-microbial communities. PMID:28424672

Differential in surface elevation change across mangrove forests in the intertidal zone

NASA Astrophysics Data System (ADS)

Fu, Haifeng; Wang, Wenqing; Ma, Wei; Wang, Mao

2018-07-01

A better understanding of surface elevation changes in different mangrove forests would improve our predictions of sea-level rise impacts, not only upon mangrove species distributions in the intertidal zone, but also on the functioning of these wetlands. Here, a two-year (2015-2017) dataset derived from 18 RSET-MH (rod surface elevation table-marker horizon) stations at Dongzhaigang Bay, Hainan, China, was analyzed to investigate how surface elevation changes differed across mangrove species zones. The current SET data indicated a rather high rate (9.6 mm y-1, on average) of surface elevation gain that was mostly consistent with that (8.1 mm y-1, on average) inferred from either the 137Cs or 210Pb dating of sediment cores. In addition, these surface elevation changes were sensitive to elevation in the intertidal zone and differed significantly between the two study sites (Sanjiang and Houpai). Mangrove species inhabiting the lower intertidal zone tended to experience greater surface elevation change at Sanjiang, which agrees with the general view that sedimentation and elevation gains are driven by elevation in the intertidal zone (i.e., greater when positioned lower in the intertidal profile). However, at Houpai, both surface elevation change and surface accretion showed the opposite trend (i.e., greater when positioned higher in the intertidal profile). This study's results indicate that the pattern of surface elevation changes across the intertidal profile maybe inconsistent due to intricate biophysical controls. Therefore, instead of using a constant rate, models should presume a topography that evolves at differing rates of surface elevation change in different species zones across the intertidal profile when predicting the impacts of sea-level rise on mangrove distributions.

Interpretation of Titan's atmospheric composition measured by Cassini-Huygens

NASA Astrophysics Data System (ADS)

Tobie, G.; Gautier, D.; Hersant, F.; Lunine, J. I.

2008-09-01

ABSTRACT The GCMS instrument aboard the Huygens probe has measured the composition of Titan's atmosphere [1] and detected for the first time 36Ar and 40Ar, but no Xe and Kr. Assuming that planetesimals which formed the satellite originated from the cold solar nebula around 10 AU, we predict, on the basis of our interpretation of the CNS enrichments in Saturn [2], that they must have contained silicates, H2O ice, CO2, CH4, H2S, NH3 and some amount of noble gases. Using the evolution model of Tobie et al. [3], we have determined the fate of the different volatile species present in Titan's interior and in the atmosphere from the accretion to present time. At the end of accretion, most of the region outward of this proto-corewas warmliquid water (T > 300K), in which gas compound has very low solubility, and so potentially very large amounts of volatiles, notably methane, ended up in the primitive atmosphere and on the surface. During that early epoch, the composition of the hot-proto atmosphere should have reflected the composition of the planetesimals. The atmosphere at that time was probablymainly composed of H2O, NH3, CO2, CH4, H2S, which strongly contrasts with the nitrogen dominating atmosphere we have on Titan today. Early escape, photolysis, impact-driven chemistry and progressive condensation to the surface of the different species initially present in the primitive atmosphere gradually change the composition of the atmosphere, so that most of the primordial gas compound disappeared fromthe atmosphere. After that catastrophic early epoch, only the inner undifferentiated portion of Titans interior was able to hold primordial volatiles. These volatile species were released fromthe deep interior when internal differentiation occured, roughly 0.5 Gyr after accretion. Depending on their ability to interact with water molecules, each species follow a different evolutionnary pathway. For pressure conditions occurringwithin Titan, we show thatmost of the volatile species combinewith watermolecules to form clathrate hydrate structure. However, the temperature at which clathration can occur depends on the properties of each molecule. Among the different species potentially present in Titan's interior, Xe and H2S are the most stable species in the clahrate phase (Figure 1), and they are the two first species to be enclathrated when the satellite cools down. Our calculations reveal that clathrates of a mixture of Xe and H2S should be sequestered at the bottom of the H2O-NH3 subsurface ocean owing to their high stability and their high density compared to that of liquid water. The preferential sequestration of xenon in Titan's interior would explain why its abundance remains below the detection limit of the Huygens GCMS [1]. On the contrary, the least stable species in the clathrate phase are argon and carbon monoxide. Therefore even if they were present in small amounts at the time of accretion, they are easily released from the interior. Furthermore, we show that only clathrates containing a significant fraction of methane have a density lower than ammonia-water mixtures. As a consequence, methane-rich clathrates released during the core overturn accumulate at the surface of the water ocean, and form a thermally insulating layer [3]. Owing to the low thermal conductivity of clathrate hydrate, the efficiency of heat transport through the icy crust is reduced, leading to an increase of the subsurface ocean temperature up to the dissociation point of methane clathrate. This lead to outgassing of methane, which occurs in three main epochs [3]. Argon and carbon monoxide, dissolved in the water ocean and contained in small amounts in the methane-rich clathrates, should also participate to this massive release of methane. A significant fraction of carbon dioxide should also be released during the outgassing episode, but it rapidly condenses onto the surface owing to the very cold surface temperature. A small amount of krypton might also be released, but as its primordial abundance is small, it remains below the detection limit of the GCMS. The detection of the 40K decay daughter 40Ar is a strong indicator of past and recent internal activities, thus confirming the scenario proposed here. While most of the detected 40Ar comes from the silicate phase, which contains a significant fraction of potassium, we show that only a small fraction of the detected 36Ar can originate from the silicate phase. This strongly suggests that most of the primordial 36Ar has been brought by the ice phase, and that a fraction of argon, even if it is small, has been incorporated at low temperature in the planetesimals that built Titan in the form of clathrate hydrate. This favors the scenario where today's methane mainly originate from the solar nebula, was stored in the interior and later released; and thus was not chemically produced H2O and CO2 in the satellite interior. In situ measurements to be done by a future mission on Titan [4] will permit to test the different ideas present here. In particular, a precise determination of D/H and O16/O18 ratios in H2O, CO2 and CO will provide pertinent tests on the origin of different volatile species. IR spectroscopy and direct sampling of the surface materials will allow to determine the amount of carbon dioxide present in the crust. Detection of 38Ar, Kr and possibly Xe, and estimation of isotopic ratios will also give key informations on the origin and evolution of Titan's atmosphere and interior, in particular on the trapping mechanismes of volatile in Saturn's environnement and on the differentiation processes of Titan's interior. References [1] Niemann, H. B., and 17 colleagues 2005. Nature 438, 779-784. [2] Hersant, F., Gautier, D., Tobie, G., Lunine, J. I. 2008. Planet Space Sci., in press. [3] Tobie, G., Lunine, J. I., Sotin, C. 2006. Nature, 440, 61-64. [4] Coustenis A. and the TANDEM consortium, 2008. Experimental Astron., in press.

Nanoscale Structure at Mineral-Fluid Interfaces

NASA Astrophysics Data System (ADS)

Sturchio, N. C.; Sturchio, N. C.; Fenter, P.; Cheng, L.; Park, C.; Zhang, Z.; Zhang, Z.; Nagy, K. L.; Schlegel, M. L.

2001-12-01

The nature of nanoparticles and their role in the natural environment is currently a subject of renewed interest. The high surface area (and surface area-to-volume ratio) of nanoparticles exerts a widespread influence on geochemical reactions and transport processes. A thorough understanding of the nanoscale world remains largely hypothetical, however, because of the challenges associated with characterizing nanoscale structures and processes. Recent insights gained from high-resolution synchrotron x-ray reflectivity measurements at the solid-fluid interfaces of macroscopic (i.e., mm-scale) mineral particles may provide relevant guidelines for expected nanoparticle surface structures. For example, at calcite-water and barite-water interfaces, undercoordinated surface cations bond with water species of variable protonation, and modest relaxations (to several hundredths of a nanometer) affect the outermost unit cells [1,2]. Undercoordinated tetrahedral ions at aluminosilicate surfaces also bond with water species, whereas interstitial or interlayer alkali or alkaline earth ions at the surface may readily exchange with hydronium or other ions; modest relaxations also affect the outermost unit cells [3,4]. Modulation of liquid water structure out to about one nanometer has been observed at the (001) cleavage surface of muscovite in deionized water, and may be present at other mineral-fluid interfaces [4]. Dissolution mechanisms at the orthoclase-water interface have been clarified by combining x-ray reflectivity and scanning force microscopy measurements [5]. Further progress in understanding nanoscale structures and processes at macroscopic mineral-water interfaces is likely to benefit nanoparticle studies. [1] Fenter et al. (2000) Geochim. Cosmochim. Acta 64, 1221-1228. [2] Fenter et al. (2001) J. Phys. Chem. B 105(34), 8112-8119. [3] Fenter et al. (2000) Geochim. Cosmochim. Acta 64, 3663-3673. [4] Cheng et al. (2001) Phys. Rev. Lett., (in press). [5] Teng et al. (2001) Geochim. Cosmochim. Acta 65, (in press).

Isolation frequency of Candida present on the surfaces of mobile phones and handsx.

PubMed

Kordecka, Anna; Krajewska-Kułak, Elżbieta; Łukaszuk, Cecylia; Kraszyńska, Bogumiła; Kułak, Wojciech

2016-06-01

It is known that mobile phones may play a role in microorganism transmission. The aim of this study was to analyze the relationship between the number of Candida genera/species isolated from samples collected from the surfaces of mobile phones and the hands of the staff as well as the preferred health-related behavior. The mycological evaluation included 175 mobile telephones and the hands of staff members at the University Hospital in Białystok, Poland. We used the Count-Tact(TM) applicator, with CandiSelect (Bio-Rad). Self-administered questionnaire was used to gather data on mobile phones disinfection practices. Assessment of the preferred health-related behavior was based on The Multidemensional Health Locus of Control Scale (MHLC). Out of 175 mobile phones, 131 (74.9 %) were colonized. Candida glabrata, C. albicans and C.krusei were isolated more frequently from the hand as well as phone surface. The mean number of Candida colonies was higher in samples collected from hand surfaces than mobile phone surfaces. No significant correlation was found between the preferred health-related behavior and the frequency of washing hands, the way of using a mobile phone, the number of colonies or the isolation frequency for the fungi collected from the surface of the phones and hands of their owners. Only 19.4 % of the participants cleaned the surface of their phones. The prevalence of mobile phone contamination by Candida is high in the University Hospital in Białystok, Poland. Candida albicans, C. glabrata, and C. krusei were the dominant species in the samples collected from mobile phones and hands. These results pose the need to develop guidelines for mobile phone disinfection.

Surface Structure and Wetting Characteristics of Collembola Cuticles

PubMed Central

Gundersen, Håkon; Leinaas, Hans Petter; Thaulow, Christian

2014-01-01

The cuticles of the arthropods Collembola (springtails) are known to be superhydrophobic, displaying such properties as water-repellence and plastron formation; overhanging surface structures have been suggested as the source of these properties. Superhydrophobicity is closely related to surface structuring and other surfaces with overhanging structures have been shown to possess robust superhydrophobic properties. In effort to correlate the wetting performance and surface structuring of the cuticles, from both a technical and evolutionary point of view, we investigated a selection of Collembola species including species from several families and covering habitats ranging from aquatic to very dry. The observed contact angles of wetting was in general larger than those predicted by the conventional models. Not all the studied Collembola were found to have superhydrophobic properties, indicating that superhydrophobicity is common, but not a universal trait in Collembola. Overhanging structures were found in some, but not all Collembola species with superhydrophobic cuticles; which leads to the conclusion that there is no direct link between overhanging surface structures and superhydrophobicity in Collembola. PMID:24498281

Surface layer formation of LiCoO2 thin film electrodes in non-aqueous electrolyte containing lithium bis(oxalate)borate

NASA Astrophysics Data System (ADS)

Matsui, Masaki; Dokko, Kaoru; Akita, Yasuhiro; Munakata, Hirokazu; Kanamura, Kiyoshi

2012-07-01

Surface layer formation processes on a LiCoO2 thin film electrode in a non-aqueous electrolyte containing lithium bis(oxalate)borate (LiBOB) were investigated using in situ FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS). The in situ FTIR spectra of the electrolyte solution containing LiBOB showed that the adsorption of BOB anions on the electrode surface occurred during the charge process of the LiCoO2 thin film electrode above 4.0 V. XPS analysis for the LiCoO2 thin film electrode charged in an electrolyte containing LiBOB suggested that the adsorbed BOB anions on the electrode surface prevent the continuous decomposition of hexafluorophosphate (PF6) anions resulting in the formation of a very thin surface layer containing organic species, while the LiCoO2 charged in a LiPF6 solution had a relatively thick surface layer containing organic species and inorganic species.

Stand, species, and individual traits impact transpiration in historically disturbed forests.

NASA Astrophysics Data System (ADS)

Blakely, B.; Rocha, A. V.; McLachlan, J. S.

2017-12-01

Historic logging disturbances have changed the structure and species composition of most Northern temperate forests. These changes impact the process of transpiration - which in turn impacts canopy surface temperature - but the links among structure, composition, and transpiration remain unclear. For this reason, ecosystem models typically use simplified structure and composition to simulate the impact of disturbances on forest transpiration. However, such simplifications ignore real variability among stands, species, and individual trees that may strongly influence transpiration across spatial and temporal scales. To capture this variability, we monitored transpiration in 48 individual trees of multiple species in both undisturbed (400+ yr) and historically logged (80 - 120 yr) forests. Using modern and historic forest surveys, we upscaled our observations to stand and regional scales to identify the key changes impacting transpiration. We extended these inferences by establishing a relationship between transpiration and measured surface temperature, linking disturbance-induced changes in structure and composition to local and regional climate. Despite greater potential evapotranspiration and basal area, undisturbed forest transpired less than disturbed (logged) forest. Transpiration was a strong predictor of surface temperature, and the canopy surface was warmer in undisturbed forest. Transpiration differences among disturbed and undisturbed forests resulted from (1) lesser transpiration and dampened seasonality in evergreen species (2) greater transpiration in younger individuals within a species, and (3) strong transpiration by large individuals. When transpiration was scaled to the stand or regional level in a simplified manner (e.g. a single transpiration rate for all deciduous individuals), the resulting estimates differed markedly from the original. Stand- species- and individual-level traits are therefore essential for understanding how transpiration and surface temperature respond to disturbance. Without consideration of such traits, current ecosystem models may struggle to capture the true impact of logging disturbances on forest transpiration.

Aureobasidium thailandensis, a new species isolated from leaves and wooden surfaces in Thailand

USDA-ARS?s Scientific Manuscript database

Aureobasidium thailandense is described from material collected on leaves and wooden surfaces in Thailand. Phylogenetically it is distinct from other species of Aureobasidium. Phenotypically it is distinguished by its cardinal temperatures, salt tolerance, and production of reddish brown hyphal pigm...

Ground level air convection produces frost damage patterns in turfgrass

NASA Astrophysics Data System (ADS)

Ackerson, Bruce J.; Beier, Richard A.; Martin, Dennis L.

2015-11-01

Frost injury patterns are commonly observed on the warm-season turfgrass species bermudagrass ( Cynodon species Rich.), zoysiagrass ( Zoysia species Willd.), and buffalograss [ Bouteloua dactyloides (Nutt.) J.T. Columbus] in cool-temperate and subtropical zones. Qualitative observations of these injury patterns are presented and discussed. A model for the formation of such patterns based on thermal instability and convection of air is presented. The characteristic length scale of the observed frost pattern injury requires a temperature profile that decreases with height from the soil to the turfgrass canopy surface followed by an increase in temperature with height above the turfgrass canopy. This is justified by extending the earth temperature theory to include a turf layer with atmosphere above it. Then the theory for a thermally unstable layer beneath a stable region by Ogura and Kondo is adapted to a turf layer to include different parameter values for pure air, as well as for turf, which is treated as a porous medium. The earlier porous medium model of Thompson and Daniels proposed to explain frost injury patterns is modified to give reasonable agreement with observed patterns.

Ground level air convection produces frost damage patterns in turfgrass.

PubMed

Ackerson, Bruce J; Beier, Richard A; Martin, Dennis L

2015-11-01

Frost injury patterns are commonly observed on the warm-season turfgrass species bermudagrass (Cynodon species Rich.), zoysiagrass (Zoysia species Willd.), and buffalograss [Bouteloua dactyloides (Nutt.) J.T. Columbus] in cool-temperate and subtropical zones. Qualitative observations of these injury patterns are presented and discussed. A model for the formation of such patterns based on thermal instability and convection of air is presented. The characteristic length scale of the observed frost pattern injury requires a temperature profile that decreases with height from the soil to the turfgrass canopy surface followed by an increase in temperature with height above the turfgrass canopy. This is justified by extending the earth temperature theory to include a turf layer with atmosphere above it. Then the theory for a thermally unstable layer beneath a stable region by Ogura and Kondo is adapted to a turf layer to include different parameter values for pure air, as well as for turf, which is treated as a porous medium. The earlier porous medium model of Thompson and Daniels proposed to explain frost injury patterns is modified to give reasonable agreement with observed patterns.

Distribution of isopod parasites in commercially important marine fishes of the Miri coast, East Malaysia.

PubMed

Anand Kumar, A; Rameshkumar, G; Ravichandran, S; Nagarajan, R; Prabakaran, K; Ramesh, M

2017-03-01

Isopods occur very commonly as parasites in food fishes. Parasitic isopods are typically marine and usually inhabit the warmer seas. They are blood-feeding; several species settle in the buccal cavity of fish, others live in the gill chamber or on the body surface including the fins. Isopods can cause morbidity and mortality in captive fish populations. The infestation usually pressure atrophy often accompanies the presence of larger parasites. The present study was aimed at collecting information on the neglected group of isopod parasites of the marine fishes from the Miri coastal environment, East Malaysia. A very little information available regarding the distribution of isopod parasites of Malaysian coastal environment. In the present study, nine isopod parasites were  oberved from ten marine fish species. The maximum number of parasites were observed in the months of June and October, 2013. Maximum prevalence was observed in October (50 %) and the minimum was observed in June (7.14 %). The parasitic infestation may lead to an economic loss in commercial fish species.

ION IRRADIATION OF ETHANE AND WATER MIXTURE ICE AT 15 K: IMPLICATIONS FOR THE SOLAR SYSTEM AND THE ISM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barros, A. L. F. de; Silveira, E. F da; Fulvio, D.

2016-06-20

Solid water has been observed on the surface of many different astronomical objects and is the dominant ice present in the universe, from the solar system (detected on the surface of some asteroids, planets and their satellites, trans-Neptunian objects [TNOs], comets, etc.) to dense cold interstellar clouds (where interstellar dust grains are covered with water-rich ices). Ethane has been detected across the solar system, from the atmosphere of the giant planets and the surface of Saturn’s satellite Titan to various comets and TNOs. To date, there were no experiments focused on icy mixtures of C{sub 2}H{sub 6} and H{sub 2}Omore » exposed to ion irradiation simulating cosmic rays, a case study for many astronomical environments in which C{sub 2}H{sub 6} has been detected. In this work, the radiolysis of a C{sub 2}H{sub 6}:H{sub 2}O (2:3) ice mixture bombarded by a 40 MeV{sup 58}Ni{sup 11+} ion beam is studied. The chemical evolution of the molecular species existing in the sample is monitored by a Fourier transform infrared spectrometer. The analysis of ethane, water, and molecular products in solid phase was performed. Induced chemical reactions in C{sub 2}H{sub 6}:H{sub 2}O ice produce 13 daughter molecular species. Their formation and dissociation cross sections are determined. Furthermore, atomic carbon, oxygen, and hydrogen budgets are determined and used to verify the stoichiometry of the most abundantly formed molecular species. The results are discussed in the view of solar system and interstellar medium chemistry. The study presented here should be regarded as a first step in laboratory works dedicated to simulate the effect of cosmic radiation on multicomponent mixtures involving C{sub 2}H{sub 6} and H{sub 2}O.« less

Kinetics and Chemistry of Ionization Wave Discharges Propagating Over Dielectric Surfaces

NASA Astrophysics Data System (ADS)

Petrishchev, Vitaly

Experimental studies of near-surface ionization wave electric discharges generated by high peak voltage (20-30 kV), nanosecond duration pulses (full width at half-maximum 50-100 ns) of positive and negative polarity and propagating over dielectric surfaces have been performed. A novel way to sustain diffuse, reproducible, ns pulse surface plasmas at a liquid-vapor interface is demonstrated at buffer gas pressures ranging from 10 to 200 Torr. Generation of surface ionization waves well reproduced shot-to-shot and sustaining diffuse near-surface plasmas is one of the principal advantages of the use of ns pulse discharge waveforms. This makes possible characterization of these plasmas in repetitively pulsed experiments. Numerous applications of these plasmas include low-temperature plasma assisted combustion, plasma fuel reforming, plasma flow control, plasma materials processing, agriculture, biology, and medicine. The objectives of the present work are (i) to demonstrate that surface ionization wave discharge plasmas sustained at a liquid-vapor interface can be used as an experimental platform for studies of near-surface plasma chemical reaction kinetics, at the conditions when the interface acts as a high-yield source of radical species, and (ii) to obtain quantitative insight into dynamics, kinetics and chemistry of surface ionization wave discharges and provide experimental data for validation of kinetic models, to assess their predictive capability. Generation of the initial radical pool may trigger a number of plasma chemical processes leading to formation of a variety of stable product species, depending on the initial composition of the liquid and the buffer gas flow. One of the products formed and detected during surface plasma / liquid water interaction is hydroxyl radical, which is closely relevant to applications of plasmas for biology and medicine. The present work includes detailed studies of surface ionization wave discharges sustained in different buffer gases over solid and liquid dielectric surfaces, such as quartz, distilled water, saline solution, and alcohols, over a wide range of pressures. Specific experiments include: measurements of ionization wave speed; plasma emission imaging using a ns gate camera; detection of surface discharge plasma chemistry products using Fourier transform infrared absorption spectroscopy; surface charge dynamics on short (ns) and long (hundreds of mus) time scales; time-resolved electron density and electron temperature measurements in a ns pulse surface discharge in helium by Thomson scattering; spatially-resolved absolute OH and H atom concentration measurements in ns pulse discharges over distilled water by single-photon and two-photon Laser Induced Fluorescence; and schlieren imaging of perturbations generated by a ns pulse dielectric barrier discharge in a surface plasma actuator in quiescent atmospheric pressure air.

Fe-Impregnated Mineral Colloids for Peroxide Activation: Effects of Mineral Substrate and Fe Precursor.

PubMed

Li, Yue; Machala, Libor; Yan, Weile

2016-02-02

Heterogeneous iron species at the mineral/water interface are important catalysts for the generation of reactive oxygen species at circumneutral pH. One significant pathway leading to the formation of such species arises from deposition of dissolved iron onto mineral colloids due to changes in redox conditions. This study investigates the catalytic properties of Fe impregnated on silica, alumina, and titania nanoparticles (as prototypical mineral colloids). Fe impregnation was carried out by immersing the mineral nanoparticles in dilute Fe(II) or Fe(III) solutions at pH 6 and 3, respectively, in an aerobic environment. The uptake of iron per unit surface area follows the order of nTiO2 > nAl2O3 > nSiO2 for both types of Fe precursors. Impregnation of mineral particles in Fe(II) solutions results in predominantly Fe(III) species due to efficient surface-mediated oxidation. The catalytic activity of the impregnated solids to produce hydroxyl radical (·OH) from H2O2 decomposition was evaluated using benzoic acid as a probe compound under dark conditions. Invariably, the rates of benzoic acid oxidation with different Fe-laden particles increase with the surface density of Fe until a critical density above which the catalytic activity approaches a plateau, suggesting active Fe species are formed predominantly at low surface loadings. The critical surface density of Fe varies with the mineral substrate as well as the aqueous Fe precursor. Fe impregnated on TiO2 exhibits markedly higher activity than its Al2O3 and SiO2 counterparts. The speciation of interfacial Fe is analyzed with diffuse reflectance UV-vis analysis and interpretation of the data in the context of benzoic oxidation rates suggests that the surface activity of the solids for ·OH generation correlates strongly with the isolated (i.e., mononuclear) Fe species. Therefore, iron dispersed on mineral colloids is a significant form of reactive iron surfaces in the aquatic environment.

Key seabird areas in southern New England identified using a community occupancy model

USGS Publications Warehouse

O'Connell, Allan F.; Flanders, Nicholas P.; Gardner, Beth; Winiarski, Kristopher J.; Paton, Peter W. C.; Allison, Taber

2015-01-01

Seabirds are of conservation concern, and as new potential risks to seabirds are arising, the need to provide unbiased estimates of species’ distributions is growing. We applied community occupancy models to detection/non-detection data collected from repeated aerial strip-transect surveys conducted in 2 large study plots off southern New England, USA; one off the coast of Rhode Island and the other in Nantucket Sound. A total of 17 seabird species were observed at least once in each study plot. We found that detection varied by survey date and effort for most species and the average detection probability across species was less than 0.4. We estimated the influence of water depth, sea surface temperature, and sea surface chl a concentration on species-specific occupancy. Diving species showed large differences between the 2 study plots in their predicted winter distributions, which were largely explained by water depth acting as a stronger predictor of occupancy in Rhode Island than in Nantucket Sound. Conversely, similarities between the 2 study plots in predicted winter distributions of surface-feeding species were explained by sea surface temperature or chlorophyll a concentration acting as predictors of these species’ occupancy in both study plots. We predicted the number of species at each site using the observed data in order to detect ‘hot-spots’ of seabird diversity and use in the 2 study plots. These results provide new information on detection of species, areas of use, and relationships with environmental variables that will be valuable for biologists and planners interested in seabird conservation in the region.

Extractable Bacterial Surface Proteins in Probiotic–Host Interaction

PubMed Central

do Carmo, Fillipe L. R.; Rabah, Houem; De Oliveira Carvalho, Rodrigo D.; Gaucher, Floriane; Cordeiro, Barbara F.; da Silva, Sara H.; Le Loir, Yves; Azevedo, Vasco; Jan, Gwénaël

2018-01-01

Some Gram-positive bacteria, including probiotic ones, are covered with an external proteinaceous layer called a surface-layer. Described as a paracrystalline layer and formed by the self-assembly of a surface-layer-protein (Slp), this optional structure is peculiar. The surface layer per se is conserved and encountered in many prokaryotes. However, the sequence of the corresponding Slp protein is highly variable among bacterial species, or even among strains of the same species. Other proteins, including surface layer associated proteins (SLAPs), and other non-covalently surface-bound proteins may also be extracted with this surface structure. They can be involved a various functions. In probiotic Gram-positives, they were shown by different authors and experimental approaches to play a role in key interactions with the host. Depending on the species, and sometime on the strain, they can be involved in stress tolerance, in survival within the host digestive tract, in adhesion to host cells or mucus, or in the modulation of intestinal inflammation. Future trends include the valorization of their properties in the formation of nanoparticles, coating and encapsulation, and in the development of new vaccines. PMID:29670603

A basin-hopping Monte Carlo investigation of the structural and energetic properties of 55- and 561-atom bimetallic nanoclusters: the examples of the ZrCu, ZrAl, and CuAl systems.

PubMed

De Souza, Douglas G; Cezar, Henrique M; Rondina, Gustavo G; de Oliveira, Marcelo F; Da Silva, Juarez L F

2016-05-05

We report a basin-hopping Monte Carlo investigation within the embedded-atom method of the structural and energetic properties of bimetallic ZrCu, ZrAl, and CuAl nanoclusters with 55 and 561 atoms. We found that unary Zr55, Zr561, Cu55, Cu561, Al55, and Al561 systems adopt the well known compact icosahedron (ICO) structure. The excess energy is negative for all systems and compositions, which indicates an energetic preference for the mixing of both chemical species. The ICO structure is preserved if a few atoms of the host system are replaced by different species, however, the composition limit in which the ICO structure is preserved depends on both the host and new chemical species. Using several structural analyses, three classes of structures, namely ideal ICO, nearly ICO, and distorted ICO structures, were identified. As the amounts of both chemical species change towards a more balanced composition, configurations far from the ICO structure arise and the dominant structures are nearly spherical, which indicates a strong minimization of the surface energy by decreasing the number of atoms with lower coordination on the surface. The average bond lengths follow Vegard's law almost exactly for ZrCu and ZrAl, however, this is not the case for CuAl. Furthermore, the radial distribution allowed us to identify the presence of an onion-like behavior in the surface of the 561-atom CuAl nanocluster with the Al atoms located in the outermost surface shell, which can be explained by the lower surface energies of the Al surfaces compared with the Cu surfaces. In ZrCu and ZrAl the radial distribution indicates a nearly homogeneous distribution for the chemical species, however, with a slightly higher concentration of Al atoms on the ZrAl surface, which can also be explained by the lower surface energy.