DOE Zero Energy Ready Home Case Study: Thrive Home Builders, Lowry Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacific Northwest National Laboratory

Thrive Home Builders built this 4,119-ft2 home at the Lowry development in Denver, Colorado, to the high-performance criteria of the U.S. Department of Energy’s Zero Energy Ready Home Program. Despite the dense positioning of the homes, mono-plane roof designs afforded plenty of space for the 8.68 kW of photovoltaic panels. With the PV, the home achieves a Home Energy Rating System (HERS) score of 4 and the home owners should enjoy energy bills of about $-11 a year. Without the PV, the home would score a HERS 38 (far lower than the HERS 80 to 100 of typical new homes).

New Whole-House Solutions Case Study: John Wesley Miller, Tucson, Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder worked with the National Association of Home Builders Research Center to build two net-zero energy homes with foam-sheathed masonry walls, low-E windows 2.9 ACH50 air sealing, transfer grilles, ducts in insulated attic, PV, and solar water heating.

Best Practices Case Study: Pulte Homes and Communities of Del Webb, Las Vegas Division

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2009-10-01

Case study of Pulte Homes Las Vegas Division, who certified nearly 1,200 homes to the DOE Builders Challenge between 2008 and 2012. All of the homes by Las Vegas’ biggest builder achieved HERS scores of lower than 70, and many floor plans got down to the mid 50s, with ducts located in sealed attics insulated along the roof line, advanced framing, and extra attention to air sealing.

TrustBuilder2: A Reconfigurable Framework for Trust Negotiation

NASA Astrophysics Data System (ADS)

Lee, Adam J.; Winslett, Marianne; Perano, Kenneth J.

To date, research in trust negotiation has focused mainly on the theoretical aspects of the trust negotiation process, and the development of proof of concept implementations. These theoretical works and proofs of concept have been quite successful from a research perspective, and thus researchers must now begin to address the systems constraints that act as barriers to the deployment of these systems. To this end, we present TrustBuilder2, a fully-configurable and extensible framework for prototyping and evaluating trust negotiation systems. TrustBuilder2 leverages a plug-in based architecture, extensible data type hierarchy, and flexible communication protocol to provide a framework within which numerous trust negotiation protocols and system configurations can be quantitatively analyzed. In this paper, we discuss the design and implementation of TrustBuilder2, study its performance, examine the costs associated with flexible authorization systems, and leverage this knowledge to identify potential topics for future research, as well as a novel method for attacking trust negotiation systems.

E-Classical Fairy Tales: Multimedia Builder as a Tool

ERIC Educational Resources Information Center

Eteokleous, Nikleia; Ktoridou, Despo; Tsolakidis, Symeon

2011-01-01

The study examines pre-service teachers' experiences in delivering a traditional-classical fairy tale using the Multimedia Builder software, in other words an e-fairy tale. A case study approach was employed, collecting qualitative data through classroom observations and focus groups. The results focus on pre-service teachers' reactions, opinions,…

JOB BUILDER remote batch processing subsystem

NASA Technical Reports Server (NTRS)

Orlov, I. G.; Orlova, T. L.

1980-01-01

The functions of the JOB BUILDER remote batch processing subsystem are described. Instructions are given for using it as a component of a display system developed by personnel of the System Programming Laboratory, Institute of Space Research, USSR Academy of Sciences.

CHARMM-GUI 10 Years for Biomolecular Modeling and Simulation

PubMed Central

Jo, Sunhwan; Cheng, Xi; Lee, Jumin; Kim, Seonghoon; Park, Sang-Jun; Patel, Dhilon S.; Beaven, Andrew H.; Lee, Kyu Il; Rui, Huan; Roux, Benoît; MacKerell, Alexander D.; Klauda, Jeffrey B.; Qi, Yifei

2017-01-01

CHARMM-GUI, http://www.charmm-gui.org, is a web-based graphical user interface that prepares complex biomolecular systems for molecular simulations. CHARMM-GUI creates input files for a number of programs including CHARMM, NAMD, GROMACS, AMBER, GENESIS, LAMMPS, Desmond, OpenMM, and CHARMM/OpenMM. Since its original development in 2006, CHARMM-GUI has been widely adopted for various purposes and now contains a number of different modules designed to set up a broad range of simulations: (1) PDB Reader & Manipulator, Glycan Reader, and Ligand Reader & Modeler for reading and modifying molecules; (2) Quick MD Simulator, Membrane Builder, Nanodisc Builder, HMMM Builder, Monolayer Builder, Micelle Builder, and Hex Phase Builder for building all-atom simulation systems in various environments; (3) PACE CG Builder and Martini Maker for building coarse-grained simulation systems; (4) DEER Facilitator and MDFF/xMDFF Utilizer for experimentally guided simulations; (5) Implicit Solvent Modeler, PBEQ-Solver, and GCMC/BD Ion Simulator for implicit solvent related calculations; (6) Ligand Binder for ligand solvation and binding free energy simulations; and (7) Drude Prepper for preparation of simulations with the CHARMM Drude polarizable force field. Recently, new modules have been integrated into CHARMM-GUI, such as Glycolipid Modeler for generation of various glycolipid structures, and LPS Modeler for generation of lipopolysaccharide structures from various Gram-negative bacteria. These new features together with existing modules are expected to facilitate advanced molecular modeling and simulation thereby leading to an improved understanding of the molecular details of the structure and dynamics of complex biomolecular systems. Here, we briefly review these capabilities and discuss potential future directions in the CHARMM-GUI development project. PMID:27862047

CHARMM-GUI 10 years for biomolecular modeling and simulation.

PubMed

Jo, Sunhwan; Cheng, Xi; Lee, Jumin; Kim, Seonghoon; Park, Sang-Jun; Patel, Dhilon S; Beaven, Andrew H; Lee, Kyu Il; Rui, Huan; Park, Soohyung; Lee, Hui Sun; Roux, Benoît; MacKerell, Alexander D; Klauda, Jeffrey B; Qi, Yifei; Im, Wonpil

2017-06-05

CHARMM-GUI, http://www.charmm-gui.org, is a web-based graphical user interface that prepares complex biomolecular systems for molecular simulations. CHARMM-GUI creates input files for a number of programs including CHARMM, NAMD, GROMACS, AMBER, GENESIS, LAMMPS, Desmond, OpenMM, and CHARMM/OpenMM. Since its original development in 2006, CHARMM-GUI has been widely adopted for various purposes and now contains a number of different modules designed to set up a broad range of simulations: (1) PDB Reader & Manipulator, Glycan Reader, and Ligand Reader & Modeler for reading and modifying molecules; (2) Quick MD Simulator, Membrane Builder, Nanodisc Builder, HMMM Builder, Monolayer Builder, Micelle Builder, and Hex Phase Builder for building all-atom simulation systems in various environments; (3) PACE CG Builder and Martini Maker for building coarse-grained simulation systems; (4) DEER Facilitator and MDFF/xMDFF Utilizer for experimentally guided simulations; (5) Implicit Solvent Modeler, PBEQ-Solver, and GCMC/BD Ion Simulator for implicit solvent related calculations; (6) Ligand Binder for ligand solvation and binding free energy simulations; and (7) Drude Prepper for preparation of simulations with the CHARMM Drude polarizable force field. Recently, new modules have been integrated into CHARMM-GUI, such as Glycolipid Modeler for generation of various glycolipid structures, and LPS Modeler for generation of lipopolysaccharide structures from various Gram-negative bacteria. These new features together with existing modules are expected to facilitate advanced molecular modeling and simulation thereby leading to an improved understanding of the structure and dynamics of complex biomolecular systems. Here, we briefly review these capabilities and discuss potential future directions in the CHARMM-GUI development project. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Industrial wastes from the boat-building sector in the Marche Region (Italy): a parametric and chemical-physical characterization.

PubMed

Carchesio, M; Tatàno, F; Tosi, G; Trivellone, C H

2013-01-01

Using the renowned leisure boat-building sector in the Marche Region (Italy) as a case-study, this paper addresses the characterization of (1) the industrial waste generation from the building of composite material-based boats and (2) some chemical-physical properties of representative types of boat-building residues (plastic foam, hardened resin, fibre-reinforced composite residues, and sanding dust). A parametric evaluation based on the number of employees gave a representative unit generation rate per employee (UGRpE) of 1.47 tons(waste) employee(-1) year(-1) for the entire Marche regional boatbuilding district, whereas evaluations carried out separately for three case-study companies provided values of 1.56, 3.07, and 1.12 tons(waste) employee(-1) year(-1) as representative for a mass-produced motor boat builder (case-study company '1'), a customized sailing boat builder (case-study company '2'), and a mould and structural component builder (case-study company '3'), respectively. The original proposal and evaluation of two additional generation rates based on physical characteristics intrinsic to the manufactured product, i.e. the unit generation rate per boat area (UGRpA) and per boat weight (UGRpW), confirmed the higher waste generation for the sailing boat builder(representative UGRpA and UGRpW values of 0.35 tons(waste) m(-2)(boat) year(-1) and 2. 71 tons(waste) tons(-1)(boat) year(-1), respectively) compared with the motor boat builder (representative UGRpA and UGRpW values of 0.06 tons(waste) m(-2)(boat) year(-1) and 0.49 tons(waste) tons(-1)(boat) year(-1), respectively). The chemical-physical property characterization of the selected residues revealed the following aspects: a general condition of low moisture contents; significant ash contents in the glass- and carbon-fibre composite residues and the correlated sanding dust; and relatively high energy content values in the overall range 14,144-32,479 kJ kg(-1), expressed as the lower heating value.

Performance Verification of Production-Scalable Energy-Efficient Solutions: Winchester/Camberley Homes Mixed-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, D.; Wiehagen, J.

2014-07-01

Winchester/Camberley Homes collaborated with the Building America team Partnership for Home Innovation to develop a new set of high performance home designs that could be applicable on a production scale. The new home designs are to be constructed in the mixed humid climate zone and could eventually apply to all of the builder's home designs to meet or exceed future energy codes or performance-based programs. However, the builder recognized that the combination of new wall framing designs and materials, higher levels of insulation in the wall cavity, and more detailed air sealing to achieve lower infiltration rates changes the moisturemore » characteristics of the wall system. In order to ensure long term durability and repeatable successful implementation with few call-backs, the project team demonstrated through measured data that the wall system functions as a dynamic system, responding to changing interior and outdoor environmental conditions within recognized limits of the materials that make up the wall system. A similar investigation was made with respect to the complete redesign of the HVAC systems to significantly improve efficiency while maintaining indoor comfort. Recognizing the need to demonstrate the benefits of these efficiency features, the builder offered a new house model to serve as a test case to develop framing designs, evaluate material selections and installation requirements, changes to work scopes and contractor learning curves, as well as to compare theoretical performance characteristics with measured results.« less

Building America

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brad Oberg

2010-12-31

Builders generally use a 'spec and purchase' business management system (BMS) when implementing energy efficiency. A BMS is the overall operational and organizational systems and strategies that a builder uses to set up and run its company. This type of BMS treats building performance as a simple technology swap (e.g. a tank water heater to a tankless water heater) and typically compartmentalizes energy efficiency within one or two groups in the organization (e.g. purchasing and construction). While certain tools, such as details, checklists, and scopes of work, can assist builders in managing the quality of the construction of higher performancemore » homes, they do nothing to address the underlying operational strategies and issues related to change management that builders face when they make high performance homes a core part of their mission. To achieve the systems integration necessary for attaining 40% + levels of energy efficiency, while capturing the cost tradeoffs, builders must use a 'systems approach' BMS, rather than a 'spec and purchase' BMS. The following attributes are inherent in a systems approach BMS; they are also generally seen in quality management systems (QMS), such as the National Housing Quality Certification program: Cultural and corporate alignment, Clear intent for quality and performance, Increased collaboration across internal and external teams, Better communication practices and systems, Disciplined approach to quality control, Measurement and verification of performance, Continuous feedback and improvement, and Whole house integrated design and specification.« less

Building America Case Study: Standard- Versus High-Velocity Air Distribution in High-Performance Townhomes, Denver, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

IBACOS investigated the performance of a small-diameter high velocity heat pump system compared to a conventional system in a new construction triplex townhouse. A ductless heat pump system also was installed for comparison, but the homebuyer backed out because of aesthetic concerns about that system. In total, two buildings, having identical solar orientation and comprised of six townhomes, were monitored for comfort and energy performance. Results show that the small-diameter system provides more uniform temperatures from floor to floor in the three-story townhome. No clear energy consumption benefit was observed from either system. The builder is continuing to explore themore » small-diameter system as its new standard system to provide better comfort and indoor air quality. The homebuilder also explored the possibility of shifting its townhome product to meet the U.S. Department of Energy Challenge Home National Program Requirements. Ultimately, the builder decided that adoption of these practices would be too disruptive midstream in the construction cycle. However, the townhomes met the ENERGY STAR Version 3.0 program requirements.« less

Children's E-Book Technology: Devices, Books, and Book Builder

ERIC Educational Resources Information Center

Shiratuddin, Norshuhada; Landoni, Monica

2003-01-01

This article describes a study of children's electronic books (e-books) technology. In particular, the focus is on devices used to access children's e-books, current available e-books and an e-book builder specifically for children. Three small case studies were conducted: two to evaluate how children accept the devices and one to test the ease of…

DOE Zero Energy Ready Home Case Study: Cobblestone Homes — 2014 Model Home, Midland, MI

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

This builder's first DOE Zero Energy Ready Home won a Custom Builder award in the 2014 Housing Innovation Awards, scored HERS 49 without PV or HERS 44 with 1.4 kW of PV, and served as a prototype and energy efficiency demonstration model while performance testing was conducted.

Cost and time study for constructing raised wood floor systems in the Gulf Coast Region of the United States

Treesearch

Marie Del Bianco; David B. McKeever; Lance Barta

2012-01-01

This report is the result of a co-operative effort between the USDA Forest Service, Forest Products Laboratory (FPL) Advanced Housing Research Center, the National Assocation of Home Builders (NAHB) Research Center, and builder members of the Metropolitan Mobile and Baldwin County Home Builders Associations. The study was undertaken to further knowledge that will...

Muscular development and lean body weight in body builders and weight lifters.

PubMed

Katch, V L; Katch, F I; Moffatt, R; Gittleson, M

1980-01-01

The extent of extreme muscular development in 39 males identified as body builders (N = 18), power weight lifters (N = 13), and Olympic weight lifters (N = 8) were studied. Body composition and anthropometric data, including calculations of pre-excess muscle body weight (scale weight minus excess muscle) were obtained. The lean body weight and percent fats of the subjects were: body builders = 74.6 kg, 9.3%; power weight lifters = 73.3 kg, 9.1%; and Olympic weight lifters = 68.2 kg, 10.8%. No group differences were present in frame size, percent fat, lean body weight, skinfolds, and diameter measurements. The only group differences were for the shoulders, chest, biceps relaxed and flexed, and forearm girths. In each case the body builders were larger. Calculations of excess muscle by the Behnke method revealed that the body builders had 15.6 kg excess muscle, power weight lifters 14.8 kg, and Olympic weight lifters 13.1 kg. Somatographic comparisons revealed only slight differences between the groups, while differences with reference man were substantial.

DOE Zero Energy Ready Home Case Study: Alliance Green Builders, Casa Aguila

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacific Northwest National Laboratory

Alliance Green Builders built this 3,129-ft2 home in the hills above Ramona, California, to the high-performance criteria of the DOE Zero Energy Ready Home (ZERH) program. The home should perform far better than net zero thanks to a super-efficient building shell, a wind turbine, three suntracking solar photovoltaic arrays, and solar thermal water heating.

Performance Verification of Production-Scalable Energy-Efficient Solutions: Winchester/Camberley Homes Mixed-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, D.; Wiehagen, J.

2014-07-01

Winchester/Camberley Homes with the Building America program and its NAHB Research Center Industry Partnership collaborated to develop a new set of high performance home designs that could be applicable on a production scale. The new home designs are to be constructed in the mixed humid climate zone four and could eventually apply to all of the builder's home designs to meet or exceed future energy codes or performance-based programs. However, the builder recognized that the combination of new wall framing designs and materials, higher levels of insulation in the wall cavity, and more detailed air sealing to achieve lower infiltrationmore » rates changes the moisture characteristics of the wall system. In order to ensure long term durability and repeatable successful implementation with few call-backs, this report demonstrates through measured data that the wall system functions as a dynamic system, responding to changing interior and outdoor environmental conditions within recognized limits of the materials that make up the wall system. A similar investigation was made with respect to the complete redesign of the heating, cooling, air distribution, and ventilation systems intended to optimize the equipment size and configuration to significantly improve efficiency while maintaining indoor comfort. Recognizing the need to demonstrate the benefits of these efficiency features, the builder offered a new house model to serve as a test case to develop framing designs, evaluate material selections and installation requirements, changes to work scopes and contractor learning curves, as well as to compare theoretical performance characteristics with measured results.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The home that won a Production Builder award in the 2014 Housing Innovation Awards serves as a model for this builder, showcasing high-tech features including an electric car charging station; a compressed natural gas (CNG) car fueling station; a greywater recycling system that filters shower, sink, and clothes washer water for yard irrigation; smart appliances; and an electronic energy management system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder certified its first DOE Zero Energy Ready Home and won a Production Builder honor in the 2014 Housing Innovation Awards. It is the first home in the world to use a tri-generation system to supply electricity, heating, and cooling on site.

Building America Case Study: Construction Guidelines for High R-Value Walls without Exterior Rigid Insulation, Cold Climate Region

DOE Office of Scientific and Technical Information (OSTI.GOV)

High-R wall assemblies (R-40 and above) are gaining popularity in the market due to programs like the DOE's Zero Energy Ready Home program, Passive House (PH), Net Zero Energy Home (NZEH) challenges in several states, and highly incentivized retrofit programs. In response to this demand, several builders have successfully used 'double wall' systems to more practically achieve higher R-values in thicker, framed walls. To builders of conventional stick-framed homes, often one of the most appealing features of double wall systems is that there are very few new exterior details. Exterior sheathing, structural bracing, house wrap or building paper, window andmore » door flashing, and siding attachment are usually identical to good details in conventional framed wall systems. The information presented in this guide is intended to reduce the risk of failure in these types of assemblies, increase durability, and result in a reduction of material brought to landfills due to failures and resulting decay. While this document focuses on double wall framing techniques, the majority of the information on how to properly construct and finish high R-value assemblies is applicable to all wall assemblies that do not have foam insulation installed on the exterior of the structural sheathing. The techniques presented have been shown through field studies to reduce the likelihood of mold growth and moisture related damage and are intended for builders, framing contractors, architects, and consultants involved in designing and building super insulated homes.« less

Intelligent Support System of Steel Technical Preparation in an Arc Furnace: Functional Scheme of Interactive Builder of the Multi Objective Optimization Problem

NASA Astrophysics Data System (ADS)

Logunova, O. S.; Sibileva, N. S.

2017-12-01

The purpose of the study is to increase the efficiency of the steelmaking process in large capacity arc furnace on the basis of implementation a new decision-making system about the composition of charge materials. The authors proposed an interactive builder for the formation of the optimization problem, taking into account the requirements of the customer, normative documents and stocks of charge materials in the warehouse. To implement the interactive builder, the sets of deterministic and stochastic model components are developed, as well as a list of preferences of criteria and constraints.

nmsBuilder: Freeware to create subject-specific musculoskeletal models for OpenSim.

PubMed

Valente, Giordano; Crimi, Gianluigi; Vanella, Nicola; Schileo, Enrico; Taddei, Fulvia

2017-12-01

Musculoskeletal modeling and simulations of movement have been increasingly used in orthopedic and neurological scenarios, with increased attention to subject-specific applications. In general, musculoskeletal modeling applications have been facilitated by the development of dedicated software tools; however, subject-specific studies have been limited also by time-consuming modeling workflows and high skilled expertise required. In addition, no reference tools exist to standardize the process of musculoskeletal model creation and make it more efficient. Here we present a freely available software application, nmsBuilder 2.0, to create musculoskeletal models in the file format of OpenSim, a widely-used open-source platform for musculoskeletal modeling and simulation. nmsBuilder 2.0 is the result of a major refactoring of a previous implementation that moved a first step toward an efficient workflow for subject-specific model creation. nmsBuilder includes a graphical user interface that provides access to all functionalities, based on a framework for computer-aided medicine written in C++. The operations implemented can be used in a workflow to create OpenSim musculoskeletal models from 3D surfaces. A first step includes data processing to create supporting objects necessary to create models, e.g. surfaces, anatomical landmarks, reference systems; and a second step includes the creation of OpenSim objects, e.g. bodies, joints, muscles, and the corresponding model. We present a case study using nmsBuilder 2.0: the creation of an MRI-based musculoskeletal model of the lower limb. The model included four rigid bodies, five degrees of freedom and 43 musculotendon actuators, and was created from 3D surfaces of the segmented images of a healthy subject through the modeling workflow implemented in the software application. We have presented nmsBuilder 2.0 for the creation of musculoskeletal OpenSim models from image-based data, and made it freely available via nmsbuilder.org. This application provides an efficient workflow for model creation and helps standardize the process. We hope this would help promote personalized applications in musculoskeletal biomechanics, including larger sample size studies, and might also represent a basis for future developments for specific applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Technology Solutions Case Study: High-Performance Ducts in Hot-Dry Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Hoeschele, A. German, E. Weitzel, R. Chitwood

2015-08-01

Ducts in conditioned space (DCS) represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. Various strategies exist for incorporating ducts within the conditioned thermal envelope. To support this activity, in 2013 the Pacific Gas & Electric Company initiated a project with Davis Energy Group (lead for the Building America team, Alliance for Residential Building Innovation) to solicit builder involvement in California to participate in field demonstrations of various DCS strategies. Builders were given incentives and design support in exchange for providing site access for construction observation, diagnostic testing, andmore » builder survey feedback. Information from the project was designed to feed into California's 2016 Title 24 process, but also to serve as an initial mechanism to engage builders in more high performance construction strategies. This Building America project complemented information collected in the California project with BEopt simulations of DCS performance in hot/dry climate regions.« less

Chemical Inventory Management at NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Kraft, Shirley S.; Homan, Joseph R.; Bajorek, Michael J.; Dominguez, Manuel B.; Smith, Vanessa L.

1997-01-01

The Chemical Management System (CMS) is a client/server application developed with Power Builder and Sybase for the Lewis Research Center (LeRC). Power Builder is a client-server application development tool, Sybase is a Relational Database Management System. The entire LeRC community can access the CMS from any desktop environment. The multiple functions and benefits of the CMS are addressed.

Unintended adverse consequences of a clinical decision support system: two cases.

PubMed

Stone, Erin G

2018-05-01

Many institutions have implemented clinical decision support systems (CDSSs). While CDSS research papers have focused on benefits of these systems, there is a smaller body of literature showing that CDSSs may also produce unintended adverse consequences (UACs). Detailed here are 2 cases of UACs resulting from a CDSS. Both of these cases were related to external systems that fed data into the CDSS. In the first case, lack of knowledge of data categorization in an external pharmacy system produced a UAC; in the second case, the change of a clinical laboratory instrument produced the UAC. CDSSs rely on data from many external systems. These systems are dynamic and may have changes in hardware, software, vendors, or processes. Such changes can affect the accuracy of CDSSs. These cases point to the need for the CDSS team to be familiar with these external systems. This team (manager and alert builders) should include members in specific clinical specialties with deep knowledge of these external systems.

Pork Barrel or Squirrel Cage? The Case of Space Standards for Laboratory Animals

ERIC Educational Resources Information Center

Wellman, Jane

2004-01-01

This article brings attention to decision-making in the world of state financing for higher education. It reflects on the origin of this field and the system builders in the 1960s and 1970s, who needed to figure out rational ways to both justify funding requests to the state and distribute resources among institutions. The article highlights one…

The design and implementation of signal decomposition system of CL multi-wavelet transform based on DSP builder

NASA Astrophysics Data System (ADS)

Huang, Yan; Wang, Zhihui

2015-12-01

With the development of FPGA, DSP Builder is widely applied to design system-level algorithms. The algorithm of CL multi-wavelet is more advanced and effective than scalar wavelets in processing signal decomposition. Thus, a system of CL multi-wavelet based on DSP Builder is designed for the first time in this paper. The system mainly contains three parts: a pre-filtering subsystem, a one-level decomposition subsystem and a two-level decomposition subsystem. It can be converted into hardware language VHDL by the Signal Complier block that can be used in Quartus II. After analyzing the energy indicator, it shows that this system outperforms Daubenchies wavelet in signal decomposition. Furthermore, it has proved to be suitable for the implementation of signal fusion based on SoPC hardware, and it will become a solid foundation in this new field.

New Whole-House Solutions Case Study: Low-Cost Evaluation of Energy Savings at the Community Scale - Fresno, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-10-01

In this project, IBACOS partnered with builder Wathen-Castanos Hybrid Homes to develop a simple and low-cost methodology by which community-scale energy savings can be evaluated based on results at the occupied test house level.Research focused on the builder and trade implementation of a whole-house systems integrated measures package and the actual utility usage in the houses at the community scale of production. Five occupants participated in this community-scale research by providing utility bills and information on occupancy and miscellaneous gas and electric appliance use for their houses. IBACOS used these utility data and background information to analyze the actual energymore » performance of the houses. Verification with measured data is an important component in predictive energy modeling. The actual utility bill readings were compared to projected energy consumption using BEopt with actual weather and thermostat set points for normalization.« less

DOE Zero Energy Ready Home Case Study: Palo Duro Homes, Albuquerque, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

Palo Duro uses advanced framing techniques like 2x6 24-inch on-center framing, open headers above windows on non-load-bearing walls, 2-stud corners, ladder blocking where walls intersect, and single top and bottom plates. These techniques reduce the amount of lumber in the wall, allowing more room for insulation and reducing costs and installation time. The builder garnered a 2013 Housing Innovation Award in the production builder category.

Building America Case Study: Zero Energy Ready Home and the Challenge of Hot Water on Demand, Denver, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

"This report outlines the steps a developer can use when looking to create and implement higher performance standards such as the U.S. Department of Energy (DOE) Zero Energy Ready Home (ZERH) standards in a community. The report also describes the specific examples of how this process was followed by a developer, Forest City, in the Stapleton community in Denver, Colorado. IBACOS described the steps used to begin to bring the DOE ZERH standard to the Forest City Stapleton community based on 15 years of community-scale development work done by IBACOS. As a result of this prior IBACOS work, the teammore » gained an understanding of the various components that a master developer needs to consider and created strategies for incorporating those components in the initial phases of development to achieve higher performance buildings in the community. An automated scoring system can be used to perform an internal audit that provides a detailed and consistent evaluation of how several homes under construction or builders' floor plans compare with the requirements of the DOE Zero Energy Ready Home program. This audit can be performed multiple times at specific milestones during construction to allow the builder to make changes as needed throughout construction for the project to meet Zero Energy Ready Home standards. This scoring system also can be used to analyze a builder's current construction practices and design.« less

A Builder`s Guide to Super Good Cents Contruction and Sales.

DOE Office of Scientific and Technical Information (OSTI.GOV)

OSU Extension Energy Program; United States. Bonneville Power Administration.

This Builder`s guide describes the Super Good Cents {reg_sign} program and the benefits available to participating builders. It explains the program standards and the typical building techniques used by Super Good Cents builders. Finally, the guide tells how you can participate and answers many of the questions asked by builders about the Super Good Cents program.

Heating, Ventilation, and Air Conditioning Design Strategy for a Hot-Humid Production Builder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerrigan, P.

2014-03-01

BSC worked directly with the David Weekley Homes - Houston division to redesign three floor plans in order to locate the HVAC system in conditioned space. The purpose of this project is to develop a cost effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses. This is in preparation for the upcoming code changes in 2015. The builder wishes to develop an upgrade package that will allow for a seamless transition to the new code mandate. The followingmore » research questions were addressed by this research project: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost? BSC and the builder developed a duct design strategy that employs a system of dropped ceilings and attic coffers for moving the ductwork from the vented attic to conditioned space. The furnace has been moved to either a mechanical closet in the conditioned living space or a coffered space in the attic.« less

HVAC Design Strategy for a Hot-Humid Production Builder, Houston, Texas (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

BSC worked directly with the David Weekley Homes - Houston division to redesign three floor plans in order to locate the HVAC system in conditioned space. The purpose of this project is to develop a cost effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses. This is in preparation for the upcoming code changes in 2015. The builder wishes to develop an upgrade package that will allow for a seamless transition to the new code mandate. The followingmore » research questions were addressed by this research project: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost? BSC and the builder developed a duct design strategy that employs a system of dropped ceilings and attic coffers for moving the ductwork from the vented attic to conditioned space. The furnace has been moved to either a mechanical closet in the conditioned living space or a coffered space in the attic.« less

DOE Zero Energy Ready Home Case Study: BPC Green Builders — Trolle Residence, Danbury, CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

The builder of this 1,650-ft2 cabin won a Custom Home honor in the 2014 Housing Innovations Awards. The home meets Passive House Standards with 5.5-in. of foil-faced polysiocyanurate foam boards lining the outside walls, R-55 of rigid EPS foam under the slab, R-86 of blown cellulose in the attic, triple-pane windows, and a single ductless heat pump to heat and cool the entire home.

DOE Zero Energy Ready Home Case Study: Green Extreme Homes & Carl Franklin Homes — First DOE Zero Energy Ready Home Retrofit, Garland, TX

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder was honored with an Affordable Builder award in the 2014 Housing Innovation Awards, for the first retrofit home certified to the DOE Zero Energy Ready home requirements.The 60-year-old, three-bedroom ranch home is expected to save its homeowner more than $1,000 a year in utility bills compared to a home built to the current 2009 International Energy Conservation Code.

DOE Zero Energy Ready Home Case Study: John Hubert Associates — EXIT-0 House, North Cape May, NJ

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This house is the first DOE Zero Energy Ready Home for this builder and won a Custom Builder award in the 2014 Housing Innovation Awards. The 1,871-ft2 home features advanced-framed above-grade walls with R-21 fiberglass batt plus an R-3.6-insulated coated OSB sheathing, R-18 rigid-foam-insulated crawlspace walls, solar water heating, a high-efficiency heat pump, an HRV, and mostly LED lighting.

Business Solutions Case Study: Marketing Zero Energy Homes: Tommy Williams Homes, Gainesville, Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Building America research has shown that high-performance homes can potentially give builders an edge in the marketplace and can boost sales, but it doesn't happen automatically. It requires a tailored, easy-to-understand marketing campaign, and sometimes a little flair. This case study highlights the successful marketing approach of Tommy Williams Homes, which devotes resources to advertising, targeted social media outlets and blogs, realtor education seminars, and groundbreaking and open house celebrations. As a result, in one community, 2013 property sales records show that TWH outsells the only other builder in the development at a higher price, with fewer days on themore » market.« less

Fast data acquisition with the CDF event builder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinervo, P.K.; Ragan, K.J.; Booth, A.W.

1989-02-01

The CDF (Collider Detector at Fermilab) Event Builder is an intelligent Fastbus device that performs parallel read out of a set of Fastbus slaves on multiple cable segments, formats the data, and writes the reformatted data to a Fastbus slave module. The authors review the properties of this device, and summarize its performance in the CDF data acquisition system.

Advanced Decentralized Water/Energy Network Design for Sustainable Infrastructure presentation at the 2012 National Association of Home Builders (NAHB) International Builders'Show

EPA Science Inventory

A university/industry panel will report on the progress and findings of a fivesteve-year project funded by the US Environmental Protection Agency. The project's end product will be a Web-based, 3D computer-simulated residential environment with a decision support system to assist...

Appliance energy efficiency in new home construction

NASA Astrophysics Data System (ADS)

1980-11-01

A survey of 224 builders was conducted to which 160 builders responded. Each respondent completed between one and seven separate questionnaires. Each of the seven questionnaires were designed to collect information about one type of equipment or major appliance. These are: heat pump; heating system; air conditioner; domestic water heater; dishwasher; range; and refrigerator. Analyses of the resulting 406 questionnaires indicated that builders were primarily responsible for brand selection. These choices were made primarily without regard for the secondary efficiency of the product. A similar apparent lack of consideration of energy efficiency during brand and model selection was found among home buyers and specialized subcontractors.

[Insulin as an anabolic: hypoglycemia in the bodybuilding world].

PubMed

Konrad, C; Schüpfer, G; Wietlisbach, M; Gerber, H

1998-07-01

Excessive body building may be dangerous. To promote athletic performance and to improve physical appearance many of the body builders abuse anabolic-androgenic steroids and other drugs. The abuse of insulin as an anabolic medication in this athletic community was followed by a case of severe hypoglycaemia in a body builder. A 30-year old male presented with cerebral symptoms of hypoglycaemia. Directly before an international competition he tried to stimulate muscle growth by using the hypoglycaemic stimulus to the growth hormone. To achieve this he injected 70 IE of a short-acting insulin subcutaneously, resulting in severe hypoglycaemia. After the initial administration of intravenous glucose by the paramedics, he lost consciousness and showed signs of convulsions. After orotracheal intubation by an emergency physician, despite of ongoing infusion of glucose the blood glucose concentration remained low as measured in the out-of-hospital setting. Finally administration of additional glucose and glucagon in the intensive care unit was able to stabilize the metabolic system. In any case of severe hypoglycaemia, repetitive measurements of blood glucose even in the prehospital setting should be performed to detect the hypoglycaemia especially if athletes are concerned.

AgBufferBuilder: A geographic information system (GIS) tool for precision design and performance assessment of filter strips

Treesearch

M. G. Dosskey; S. Neelakantan; T. G. Mueller; T. Kellerman; M. J. Helmers; E. Rienzi

2015-01-01

Spatially nonuniform runoif reduces the water qua1iry perfortnance of constant- width filter strips. A geographic inlormation system (Gls)-based tool was developed and tested that ernploys terrain analysis to account lor spatially nonuniform runoffand produce more ellbctive filter strip designs.The computer program,AgBufTerBuilder, runs with ATcGIS versions 10.0 and 10...

Transitioning to High Performance Homes: Successes and Lessons Learned From Seven Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widder, Sarah H.; Kora, Angela R.; Baechler, Michael C.

2013-03-01

As homebuyers are becoming increasingly concerned about rising energy costs and the impact of fossil fuels as a major source of greenhouse gases, the returning new home market is beginning to demand energy-efficient and comfortable high-performance homes. In response to this, some innovative builders are gaining market share because they are able to market their homes’ comfort, better indoor air quality, and aesthetics, in addition to energy efficiency. The success and marketability of these high-performance homes is creating a builder demand for house plans and information about how to design, build, and sell their own low-energy homes. To help makemore » these and other builders more successful in the transition to high-performance construction techniques, Pacific Northwest National Laboratory (PNNL) partnered with seven interested builders in the hot humid and mixed humid climates to provide technical and design assistance through two building science firms, Florida Home Energy and Resources Organization (FL HERO) and Calcs-Plus, and a designer that offers a line of stock plans designed specifically for energy efficiency, called Energy Smart Home Plans (ESHP). This report summarizes the findings of research on cost-effective high-performance whole-house solutions, focusing on real-world implementation and challenges and identifying effective solutions. The ensuing sections provide project background, profile each of the builders who participated in the program, and describe their houses’ construction characteristics, key challenges the builders encountered during the construction and transaction process); and present primary lessons learned to be applied to future projects. As a result of this technical assistance, 17 homes have been built featuring climate-appropriate efficient envelopes, ducts in conditioned space, and correctly sized and controlled heating, ventilation, and air-conditioning systems. In addition, most builders intend to integrate high-performance features into most or all their homes in the future. As these seven builders have demonstrated, affordable, high-performance homes are possible, but require attention to detail and flexibility in design to accommodate specific regional geographic or market-driven constraints that can increase cost. With better information regarding how energy-efficiency trade-offs or design choices affect overall home performance, builders can make informed decisions regarding home design and construction to minimize cost without sacrificing performance and energy savings.« less

Achieving Challenge Home in Affordable Housing in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beal, D.; McIlvaine, J.; Winter, B.

2014-08-01

The Building America Partnership for Improved Residential Construction (BA-PIRC), one of the Building America research team leads, has partnered with two builders as they work through the Challenge Home certification process in one test home each. The builder partners participating in this cost-shared research are Southeast Volusia County Habitat for Humanity near Daytona, Florida and Manatee County Habitat for Humanity near Tampa, Florida. Both are affiliates of Habitat for Humanity International, a non-profit affordable housing organization. This research serves to identify viable technical pathways to meeting the CH criteria for other builders in the region. A further objective of thismore » research is to identify gaps and barriers in the marketplace related to product availability, labor force capability, code issues, cost effectiveness, and business case issues that hinder or prevent broader adoption on a production scale.« less

Achieving Challenge Home in Affordable Housing in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beal, D.; McIlvaine, J.; Winter, B.

2014-08-01

The Building America Partnership for Improved Residential Construction (BA-PIRC), one of the Building America research team leads, has partnered with two builders as they work through the Challenge Home certification process (now Zero Energy Ready Home) in one test home each. The builder partners participating in this cost-shared research are Southeast Volusia County Habitat for Humanity near Daytona, Florida and Manatee County Habitat for Humanity near Tampa, Florida. Both are affiliates of Habitat for Humanity International, a non-profit affordable housing organization. This research serves to identify viable technical pathways to meeting the CH criteria for other builders in the region.more » A further objective of this research is to identify gaps and barriers in the marketplace related to product availability, labor force capability, code issues, cost effectiveness, and business case issues that hinder or prevent broader adoption on a production scale.« less

e-Stars Template Builder

NASA Technical Reports Server (NTRS)

Cox, Brian

2003-01-01

e-Stars Template Builder is a computer program that implements a concept of enabling users to rapidly gain access to information on projects of NASA's Jet Propulsion Laboratory. The information about a given project is not stored in a data base, but rather, in a network that follows the project as it develops. e-Stars Template Builder resides on a server computer, using Practical Extraction and Reporting Language (PERL) scripts to create what are called "e-STARS node templates," which are software constructs that allow for project-specific configurations. The software resides on the server and does not require specific software on the user machine except for an Internet browser. A user's computer need not be equipped with special software (other than an Internet-browser program). e-Stars Template Builder is compatible with Windows, Macintosh, and UNIX operating systems. A user invokes e-Stars Template Builder from a browser window. Operations that can be performed by the user include the creation of child processes and the addition of links and descriptions of documentation to existing pages or nodes. By means of this addition of "child processes" of nodes, a network that reflects the development of a project is generated.

Building America Best Practices Series Volume 11. Builders Challenge Guide to 40% Whole-House Energy Savings in the Marine Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2010-09-01

This best practices guide is the eleventh in a series of guides for builders produced by the U.S. Department of Energy’s Building America Program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the marine climate (portions of Washington, Oregon, and California) can achieve homes that have whole house energy savings of 40% over the Building America benchmark (a home built to mid-1990s buildingmore » practices roughly equivalent to the 1993 Model Energy Code) with no added overall costs for consumers. These best practices are based on the results of research and demonstration projects conducted by Building America’s research teams. The guide includes information for managers, designers, marketers, site supervisors, and subcontractors, as well as case studies of builders who are successfully building homes that cut energy use by 40% in the marine climate. This document is available on the web at www.buildingamerica.gov. This report was originally cleared 06-29-2010. This version is Rev 1 cleared in Nov 2010. The only change is the reference to the Energy Star Windows critieria shown on pg 8.25 was updated to match the criteria - Version 5.0, 04/07/2009, effective 01/04/2010.« less

Space Fabrication Demonstration System

NASA Technical Reports Server (NTRS)

1978-01-01

The completion of assembly of the beam builder and its first automatic production of truss is discussed. A four bay, hand assembled, roll formed members truss was built and tested to ultimate load. Detail design of the fabrication facility (beam builder) was completed and designs for subsystem debugging are discussed. Many one bay truss specimens were produced to demonstrate subsystem operation and to detect problem areas.

A Builder's Guide to Super Good Cents Contruction and Sales.

DOE Office of Scientific and Technical Information (OSTI.GOV)

OSU Extension Energy Program; United States. Bonneville Power Administration.

This Builder's guide describes the Super Good Cents {reg sign} program and the benefits available to participating builders. It explains the program standards and the typical building techniques used by Super Good Cents builders. Finally, the guide tells how you can participate and answers many of the questions asked by builders about the Super Good Cents program.

Builders Challenge High Performance Builder Spotlight - Martha Rose Construction, Inc., Seattle, Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2008-01-01

Building America/Builders Challenge fact sheet on Martha Rose Construction, an energy-efficient home builder in marine climate using the German Passiv Haus design, improved insulation, and solar photovoltaics.

New Whole-House Solutions Case Study: A Production Builder's Passive House - Denver, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Brookfield Home’s first project is in a community called Midtown in Denver, Colorado, in which the builder took on the challenge of increased energy efficiency by creating a Passive House (PH)-certified model home. Brookfield worked with the U.S. Department of Energy’s Building America research team IBACOS to create the home, evaluate advanced building technologies, and use the home as a marketing tool for potential homebuyers. Brookfield also worked with KGA studio architects to create a new floor plan that would be constructed to the PH standard as an upgrade option.

DOE Zero Energy Ready Home Case Study: Transformations, Inc., Custom House, Devens, Massachusetts

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

This single-family home features a superinsulated shell with 12-inch double walls filled with open cell spray foam, as well as R-5 triple-pane windows. The 18.33 kW photovoltaic system can produce all the electricity the home can use in a year with enough left over to power an electric car for 30,000 miles.These features helped the builder to win a 2013 Housing Innovation Award in the custom home category.

76 FR 2145 - Masco Builder Cabinet Group Including On-Site Leased Workers From Reserves Network, Jackson, OH...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-12

...,287B; TA-W-71,287C] Masco Builder Cabinet Group Including On-Site Leased Workers From Reserves Network, Jackson, OH; Masco Builder Cabinet Group, Waverly, OH; Masco Builder Cabinet Group, Seal Township, OH; Masco Builder Cabinet Group, Seaman, OH; Amended Certification Regarding Eligibility To Apply for Worker...

Building America Case Study: Low-Cost Evaluation of Energy Savings at the Community Scale, Fresno, California (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-10-01

A new construction pilot community was constructed by builder-partner Wathen-Castanos Hybrid Homes (WCHH) based on a single occupied test house that was designed to achieve greater than 30% energy savings with respect to the House Simulation Protocols (Hendron, Robert; Engebrecht, Cheryn (2010). Building America House Simulation Protocols. Golden, CO: National Renewable Energy Laboratory.). Builders face several key problems when implementing a whole-house systems integrated measures package (SIMP) from a single test house into multiple houses. Although a technical solution already may have been evaluated and validated in an individual test house, the potential exists for constructability failures at the communitymore » scale. This report addresses factors of implementation and scalability at the community scale and proposes methodologies by which community-scale energy evaluations can be performed based on results at the occupied test house level. Research focused on the builder and trade implementation of a SIMP and the actual utility usage in the houses at the community scale of production. Five occupants participated in this community-scale research by providing utility bills and information on occupancy and miscellaneous gas and electric appliance use for their houses. IBACOS used these utility data and background information to analyze the actual energy performance of the houses. Verification with measured data is an important component in predictive energy modeling. The actual utility bill readings were compared to projected energy consumption using BEopt with actual weather and thermostat set points for normalization.« less

Builders Challenge High Performance Builder Spotlight: Yavapai College, Chino Valley, Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2009-12-22

Building America Builders Challenge fact sheet on Yavapai College of Chino Valley, Arizona. These college students built a Building America Builders Challenge house that achieved the remarkably low HERS score of -3 and achieved a tight building envelope.

CHARMM-GUI Membrane Builder toward realistic biological membrane simulations.

PubMed

Wu, Emilia L; Cheng, Xi; Jo, Sunhwan; Rui, Huan; Song, Kevin C; Dávila-Contreras, Eder M; Qi, Yifei; Lee, Jumin; Monje-Galvan, Viviana; Venable, Richard M; Klauda, Jeffery B; Im, Wonpil

2014-10-15

CHARMM-GUI Membrane Builder, http://www.charmm-gui.org/input/membrane, is a web-based user interface designed to interactively build all-atom protein/membrane or membrane-only systems for molecular dynamics simulations through an automated optimized process. In this work, we describe the new features and major improvements in Membrane Builder that allow users to robustly build realistic biological membrane systems, including (1) addition of new lipid types, such as phosphoinositides, cardiolipin (CL), sphingolipids, bacterial lipids, and ergosterol, yielding more than 180 lipid types, (2) enhanced building procedure for lipid packing around protein, (3) reliable algorithm to detect lipid tail penetration to ring structures and protein surface, (4) distance-based algorithm for faster initial ion displacement, (5) CHARMM inputs for P21 image transformation, and (6) NAMD equilibration and production inputs. The robustness of these new features is illustrated by building and simulating a membrane model of the polar and septal regions of E. coli membrane, which contains five lipid types: CL lipids with two types of acyl chains and phosphatidylethanolamine lipids with three types of acyl chains. It is our hope that CHARMM-GUI Membrane Builder becomes a useful tool for simulation studies to better understand the structure and dynamics of proteins and lipids in realistic biological membrane environments. Copyright © 2014 Wiley Periodicals, Inc.

Object Toolkit Version 4.3 User’s Manual

DTIC Science & Technology

2016-12-31

unlimited. (OPS-17-12855 dtd 19 Jan 2017) 13. SUPPLEMENTARY NOTES 14. ABSTRACT Object Toolkit is a finite - element model builder specifically designed for...INTRODUCTION 1 What Is Object Toolkit? Object Toolkit is a finite - element model builder specifically designed for creating representations of spacecraft...Nascap-2k and EPIC, the user is not required to purchase or learn expensive finite element generators to create system models. Second, Object Toolkit

Mini-Split Heat Pump Evaluation and Zero Energy Ready Home Support

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herk, Anastasia

IBACOS worked with builder Imagine Homes to evaluate the performance of an occupied new construction test house following construction of the house in the hot, humid climate of San Antonio, Texas. The project measures the effectiveness of a space conditioning strategy using a multihead mini-split heat pump (MSHP) system in a reduced-load home to achieve acceptable comfort levels (temperature and humidity) and energy performance. IBACOS collected long-term data and analyzed the energy consumption and comfort conditions of the occupied house after one year of operation. Although measured results indicate that the test system provides comfort both inside and outside themore » ASHRAE Standard 55-2010 range, the occupants of the house claimed both adequate comfort and appreciation of the ease of use and flexibility of the installed MSHP system. IBACOS also assisted the builder to evaluate design and specification changes necessary to comply with Zero Energy Ready Home, but the builder chose to not move forward with it because of concerns about the 'solar ready' requirements of the program.« less

DOE ZERH Case Study: Sunroc Builders, Bates Avenue, Lakeland, FL

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2015-09-01

Case study of a DOE 2015 Housing Innovation Award winning affordable home in the hot-humid climate that got HERS 57 without PV, with 6.5” SIP walls and 8.25” SIP roof; uninsulated slab foundation; fresh air intake; SEER 16 ducted air source heat pump.

Best Practices Case Study: Imagine Homes - Stillwater Ranch, San Antonio, TX

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2011-04-01

This case study describes Imagine Homes, who met Builders Challenge criteria on more than 200 homes in San Antonio with rigid foam exterior sheathing, ducts and air handler in conditioned space in a spray-foam insulated attic, and high-efficiency HVAC, windows, and appliances.

Practices and Processes of Leading High Performance Home Builders in the Upper Midwest

DOE Office of Scientific and Technical Information (OSTI.GOV)

Von Thoma, E.; Ojczyk, C.

2012-12-01

The NorthernSTAR Building America Partnership team proposed this study to gain insight into the business, sales, and construction processes of successful high performance builders. The knowledge gained by understanding the high performance strategies used by individual builders, as well as the process each followed to move from traditional builder to high performance builder, will be beneficial in proposing more in-depth research to yield specific action items to assist the industry at large transform to high performance new home construction. This investigation identified the best practices of three successful high performance builders in the upper Midwest. In-depth field analysis of themore » performance levels of their homes, their business models, and their strategies for market acceptance were explored. All three builders commonly seek ENERGY STAR certification on their homes and implement strategies that would allow them to meet the requirements for the Building America Builders Challenge program. Their desire for continuous improvement, willingness to seek outside assistance, and ambition to be leaders in their field are common themes. Problem solving to overcome challenges was accepted as part of doing business. It was concluded that crossing the gap from code-based building to high performance based building was a natural evolution for these leading builders.« less

Evaluation of the U.S. Department of Energy Challenge Home Program Certification of Production Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerrigan, P.; Loomis, H.

2014-09-01

The purpose of this project was to evaluate integrated packages of advanced measures in individual test homes to assess their performance with respect to Building America Program goals, specifically compliance with the DOE Challenge Home Program. BSC consulted on the construction of five test houses by three Cold Climate production builders in three separate US cities. BSC worked with the builders to develop a design package tailored to the cost-related impacts for each builder. Therefore, the resulting design packages do vary from builder to builder. BSC provided support through this research project on the design, construction and performance testing ofmore » the five test homes. Overall, the builders have concluded that the energy related upgrades (either through the prescriptive or performance path) represent reasonable upgrades. The builders commented that while not every improvement in specification was cost effective (as in a reasonable payback period), many were improvements that could improve the marketability of the homes and serve to attract more energy efficiency discerning prospective homeowners. However, the builders did express reservations on the associated checklists and added certifications. An increase in administrative time was observed with all builders. The checklists and certifications also inherently increase cost due to: 1. Adding services to the scope of work for various trades, such as HERS Rater, HVAC contractor; 2. Increased material costs related to the checklists, especially the EPA Indoor airPLUS and EPA WaterSense(R) Efficient Hot Water Distribution requirement.« less

38 CFR 36.4526 - Issuance of fund reservation commitments.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for the making of loans to eligible veterans for the purchase or construction of such dwellings. Such... case in which it determines that the experience or technical qualifications of the builder in respect...

Builder 1 & C: Naval Training Command Rate Training Manual. Revised 1973.

ERIC Educational Resources Information Center

Naval Training Command, Pensacola, FL.

The training manual is designed to help Navy personnel meet the occupational qualifications for advancement to Builder First Class and Chief Builder. The introductory chapter provides information to aid personnel in their preparation for advancement and outlines the scope of the Builder rating and the types of billets to which he can be assigned.…

Space Construction Automated Fabrication Experiment Definition Study (SCAFEDS), part 3. Volume 2: Study results

NASA Technical Reports Server (NTRS)

1979-01-01

The detailed results of all part 3 study tasks are presented. Selected analysis was performed on the beam builder conceptual design. The functions of the beam builder and a ground test beam builder were defined. Jig and fixture concepts were developed and the developmental plans of the beam builder were expounded.

Transforming the U.S. Immigration System After 9/11: The Impact of Organizational Change and Collaboration in the Context of Homeland Security

DTIC Science & Technology

2008-12-01

disqualifying criminal conviction from an application to become a Lawful Permanent Resident of the U.S.10 10...developing Collaborative Capacity Builders (CCBs) is another method to sustain and continue to build an effective USCIS and ICE network into the 21st...Weber and Anne M. Khademian, “Wicked Problems, Knowledge Challenges, and Collaborative Capacity Builders in Network Settings,” Public Administration

Radon

MedlinePlus

... My Home? Radon Guide for Tenants Builders and Contractors Radon-Resistant Construction Basics and Techniques EPA's Directory of Builders Resources for Builders and Contractors Radon Action Plans The National Radon Action Plan ( ...

Continuation of research into language concepts for the mission support environment

NASA Technical Reports Server (NTRS)

1991-01-01

A concept for a more intuitive and graphically based Computation (Comp) Builder was developed. The Graphical Comp Builder Prototype was developed, which is an X Window based graphical tool that allows the user to build Comps using graphical symbols. Investigation was conducted to determine the availability and suitability of the Ada programming language for the development of future control center type software. The Space Station Freedom Project identified Ada as the desirable programming language for the development of Space Station Control Center software systems.

PiVoT GPS Receiver

NASA Technical Reports Server (NTRS)

Wennersten, Miriam; Banes, Vince; Boegner, Greg; Clagnett, Charles; Dougherty, Lamar; Edwards, Bernard; Roman, Joe; Bauer, Frank H. (Technical Monitor)

2001-01-01

NASA Goddard Space Flight Center has built an open architecture, 24 channel spaceflight Global Positioning System (GPS) receiver. The compact PCI PiVoT GPS receiver card is based on the Mitel/GEC Plessey Builder 2 board. PiVoT uses two Plessey 2021 correlators to allow tracking of up to 24 separate GPS SV's on unique channels. Its four front ends can support four independent antennas, making it a useful card for hosting GPS attitude determination algorithms. It has been built using space quality, radiation tolerant parts. The PiVoT card works at a lower signal to noise ratio than the original Builder 2 board. It also hosts an improved clock oscillator. The PiVoT software is based on the original Piessey Builder 2 software ported to the Linux operating system. The software is posix compliant and can be easily converted to other posix operating systems. The software is open source to anyone with a licensing agreement with Plessey. Additional tasks can be added to the software to support GPS science experiments or attitude determination algorithms. The next generation PiVoT receiver will be a single radiation hardened compact PCI card containing the microprocessor and the GPS receiver optimized for use above the GPS constellation.

Building America Top Innovations 2012: Reduced Call-Backs with High-Performance Production Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-01-01

This Building America Top Innovations profile describes ways Building America teams have helped builders cut call-backs. Harvard University study found builders who worked with Building America had a 50% drop in call-backs. One builder reported a 50-fold reduction in the incidence of pipe freezing, a 50% reduction in drywall cracking, and a 60% decline in call-backs.

Solving a real-world problem using an evolving heuristically driven schedule builder.

PubMed

Hart, E; Ross, P; Nelson, J

1998-01-01

This work addresses the real-life scheduling problem of a Scottish company that must produce daily schedules for the catching and transportation of large numbers of live chickens. The problem is complex and highly constrained. We show that it can be successfully solved by division into two subproblems and solving each using a separate genetic algorithm (GA). We address the problem of whether this produces locally optimal solutions and how to overcome this. We extend the traditional approach of evolving a "permutation + schedule builder" by concentrating on evolving the schedule builder itself. This results in a unique schedule builder being built for each daily scheduling problem, each individually tailored to deal with the particular features of that problem. This results in a robust, fast, and flexible system that can cope with most of the circumstances imaginable at the factory. We also compare the performance of a GA approach to several other evolutionary methods and show that population-based methods are superior to both hill-climbing and simulated annealing in the quality of solutions produced. Population-based methods also have the distinct advantage of producing multiple, equally fit solutions, which is of particular importance when considering the practical aspects of the problem.

New Whole-House Case Study: William Ryan Homes, Tampa, Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The builder worked with Consortium for Advanced Residential Buildings to design HERS-65 homes with energy-efficient heat pumps and programmable thermostats with humidity controls, foam-filled concrete block walls, draining house wrap, and airsealed kneewalls.

New Whole-House Solutions Case Study: Tindall Homes, Columbus, New Jersey

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The builder worked with IBACOS to build 20 HERS-58 homes with R-49 mixed attic insulation, poly-iso foam in advanced framed walls, precast concrete basement walls with rigid foam, tight airsealing, and HRV

System Diagnostic Builder - A rule generation tool for expert systems that do intelligent data evaluation. [applied to Shuttle Mission Simulator

NASA Technical Reports Server (NTRS)

Nieten, Joseph; Burke, Roger

1993-01-01

Consideration is given to the System Diagnostic Builder (SDB), an automated knowledge acquisition tool using state-of-the-art AI technologies. The SDB employs an inductive machine learning technique to generate rules from data sets that are classified by a subject matter expert. Thus, data are captured from the subject system, classified, and used to drive the rule generation process. These rule bases are used to represent the observable behavior of the subject system, and to represent knowledge about this system. The knowledge bases captured from the Shuttle Mission Simulator can be used as black box simulations by the Intelligent Computer Aided Training devices. The SDB can also be used to construct knowledge bases for the process control industry, such as chemical production or oil and gas production.

Moisture Performance of High-R Wall Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, Nay B.; Kochkin, Vladimir

High-performance homes offer improved comfort, lower utility bills, and assured durability. The next generation of building enclosures is a key step toward achieving high-performance goals through decreasing energy load demand and enabling advanced space-conditioning systems. Yet the adoption of high-R enclosures and particularly high-R walls has been a slow-growing trend because mainstream builders are hesitant to make the transition. In a survey of builders on this topic, one of the challenges identifi ed is an industry-wide concern about the long-term moisture performance of energy-effi cient walls. This study takes a step toward addressing this concern through direct monitoring of themore » moisture performance of high-R walls in occupied homes in several climate zones. In addition, the robustness of the design and modeling tools for selecting high-R wall solutions is evaluated using the monitored data from the field. The information and knowledge gained through this research will provide an objective basis for decision-making so that builders can implement advanced designs with confidence.« less

Adding run history to CLIPS

NASA Technical Reports Server (NTRS)

Tuttle, Sharon M.; Eick, Christoph F.

1991-01-01

To debug a C Language Integrated Production System (CLIPS) program, certain 'historical' information about a run is needed. It would be convenient for system builders to have the capability to request such information. We will discuss how historical Rete networks can be used for answering questions that help a system builder detect the cause of an error in a CLIPS program. Moreover, the cost of maintaining a historical Rete network is compared with that for a classical Rete network. We will demonstrate that the cost for assertions is only slightly higher for a historical Rete network. The cost for handling retraction could be significantly higher; however, we will show that by using special data structures that rely on hashing, it is also possible to implement retractions efficiently.

Heating, Ventilation, and Air Conditioning Design Strategy for a Hot-Humid Production Builder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerrigan, P.

2014-03-01

Building Science Corporation (BSC) worked directly with the David Weekley Homes - Houston division to develop a cost-effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses in preparation for the upcoming code changes in 2015. This research project addressed the following questions: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences?more » 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost?« less

New Whole-House Solutions Case Study: Pulte Homes, Las Vegas, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

The builder teamed with Building Science Corporation to design HERS-54 homes with high-efficiency HVAC with ducts in conditioned space, jump ducts, and a fresh air intake; advanced framed walls; low-e windows; and PV roof tiles.

Building America Case Study: Duct in Conditioned Space in a Dropped Ceiling or Fur-down, Gainesville, Florida (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-09-01

Forced air distribution systems (duct systems) typically are installed out of sight for aesthetic reasons, most often in unconditioned areas such as an attic or crawlspace. Any leakage of air to or from the duct system (duct leakage) in unconditioned space not only loses energy, but impacts home and equipment durability and indoor air quality. An obvious solution to this problem is to bring the duct system into the interior of the house, either by sealing the area where the ducts are installed (sealed attic or crawlspace) or by building an interior cavity or chase above the ceiling plane (raisedmore » ceiling or fur-up chase) or below the ceiling plane (dropped ceiling or fur-down) for the duct system. This case study examines one Building America builder partner's implementation of an inexpensive, quick and effective method of building a fur-down or dropped ceiling chase.« less

Evaluation of the U.S. Department of Energy Challenge Home Program Certification of Production Builders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerrigan, P.; Loomis, H.

2014-09-01

The purpose of this project was to evaluate integrated packages of advanced measures in individual test homes to assess their performance with respect to Building America program goals, specifically compliance with the DOE Challenge Home Program. BSC consulted on the construction of five test houses by three cold climate production builders in three U.S. cities and worked with the builders to develop a design package tailored to the cost-related impacts for each builder. Also, BSC provided support through performance testing of the five test homes. Overall, the builders have concluded that the energy related upgrades (either through the prescriptive ormore » performance path) represent reasonable upgrades. The builders commented that while not every improvement in specification was cost effective (as in a reasonable payback period), many were improvements that could improve the marketability of the homes and serve to attract more energy efficiency discerning prospective homeowners. However, the builders did express reservations on the associated checklists and added certifications. An increase in administrative time was observed with all builders. The checklists and certifications also inherently increase cost due to: adding services to the scope of work for various trades, such as HERS Rater, HVAC contractor; and increased material costs related to the checklists, especially the EPA Indoor airPLUS and EPA WaterSense® Efficient Hot Water Distribution requirement.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder built fourteen homes in the Gordon Estates subdivision that achieved Challenge Home certification with HERS 38–58 on an affordable budget for homeowners. Every Mandalay home in the development also met the National Green Building Standard gold level. The Gordon Estates subdivision is also serving as a showcase of energy efficiency, and Mandalay is hosting education workshops for realtors, state and local officials, other builders, students, potential homeowners, and the public. The builder won a 2013 Housing Innovation Award in the affordable builder category.

Knowledge transfer to builders in post-disaster housing reconstruction in West-Sumatra of Indonesia

NASA Astrophysics Data System (ADS)

Hidayat, Benny; Afif, Zal

2017-11-01

Housing is the most affected sector by disasters as can be observed after the 2009 earthquake in West Sumatra province in Indonesia. As in Indonesian construction industry, the housing post-disaster reconstruction is influenced by knowledge and skills of builders or laborers, or locally known as `tukang'. After the earthquake there were trainings to transfer knowledge about earthquake-safe house structure for the builders in the post-disaster reconstruction. This study examined the effectiveness of the training in term of understanding of the builders and application of the new knowledge. Ten semi-structured interviews with the builders were conducted in this study. The results indicate that the builders with prior housing construction experience can absorb and understand the new knowledge about earthquake-safe house structure. Combination of lecturing and practice sessions also help the builders to understand the knowledge. However, findings of this research also suggest there is a problem in implementation of the new knowledge. Utilization of earthquake-safe house structure may leads to a rise in house cost. As a result, some house owners prefer to save money than to adopt the new knowledge.

Performance of the CMS Event Builder

NASA Astrophysics Data System (ADS)

Andre, J.-M.; Behrens, U.; Branson, J.; Brummer, P.; Chaze, O.; Cittolin, S.; Contescu, C.; Craigs, B. G.; Darlea, G.-L.; Deldicque, C.; Demiragli, Z.; Dobson, M.; Doualot, N.; Erhan, S.; Fulcher, J. F.; Gigi, D.; Gładki, M.; Glege, F.; Gomez-Ceballos, G.; Hegeman, J.; Holzner, A.; Janulis, M.; Jimenez-Estupiñán, R.; Masetti, L.; Meijers, F.; Meschi, E.; Mommsen, R. K.; Morovic, S.; O'Dell, V.; Orsini, L.; Paus, C.; Petrova, P.; Pieri, M.; Racz, A.; Reis, T.; Sakulin, H.; Schwick, C.; Simelevicius, D.; Zejdl, P.

2017-10-01

The data acquisition system (DAQ) of the CMS experiment at the CERN Large Hadron Collider assembles events at a rate of 100 kHz, transporting event data at an aggregate throughput of {\\mathscr{O}}(100 {{GB}}/{{s}}) to the high-level trigger farm. The DAQ architecture is based on state-of-the-art network technologies for the event building. For the data concentration, 10/40 Gbit/s Ethernet technologies are used together with a reduced TCP/IP protocol implemented in FPGA for a reliable transport between custom electronics and commercial computing hardware. A 56 Gbit/s Infiniband FDR Clos network has been chosen for the event builder. This paper presents the implementation and performance of the event-building system.

DOE Zero Energy Ready Home Case Study: Caldwell and Johnson — Church Community and Housing Corporation, Charlestown, RI

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

This DOE Zero Energy Ready Home garnered an Affordable Builder award in the 2014 Housing Innovation Awards, for its highly insulated construction, minisplit heat pump and water heater, and triple pane windows.

Builders Challenge High Performance Builder Spotlight: Artistic Homes, Albuquerque, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2009-12-22

Building America Builders Challenge fact sheet on Artistic Homes of Albuquerque, New Mexico. Standard features of their homes include advanced framed 2x6 24-inch on center walls, R-21 blown insulation in the walls, and high-efficiency windows.

Green Builder Coalition |

Science.gov Websites

- Learn More Here - Join the Green Builder® Coalition today! - The Coalition supports the SAVE Act Assistance Advocacy Member Benefits Join Contact © 2016 Green Builder Coalition - Newsletter Signup - info @greenbuildercoalition.org - This site is green - Website by Triple Smart Follow Us

Class in construction: London building workers, dirty work and physical cultures.

PubMed

Thiel, Darren

2007-06-01

Descriptions of manual employment tend to ignore its diversity and overstate the homogenizing effects of technology and industrialization. Based on ethnographic research on a London construction site, building work was found to be shaped by the forms of a pre-industrial work pattern characterized by task autonomy and freedom from managerial control. The builders' identities were largely free from personal identification as working class, and collective identification was fractured by trade status, and ethnic and gender divisions. Yet the shadow of a class-based discursive symbolism, which centered partly on the division of minds/bodies, mental/manual, and clean/dirty work, framed their accounts, identities and cultures. The builders displayed what is frequently termed working-class culture, and it was highly masculine. This physical and bodily-centered culture shielded them from the possible stigmatization of class and provided them with a source of localized capital. 'Physical capital' in conjunction with social capital (the builders' networks of friends and family) had largely guided their position in the stratification system, and values associated with these forms of capital were paramount to their public cultures. This cultural emphasis offered a continuing functionality in the builders' lives, not having broken free from tradition or becoming an object of reflexive choice.

Wildlife Scenario Builder and User's Guide (Version 1.0, Beta Test)

EPA Science Inventory

The Wildlife Scenario Builder (WSB) was developed to improve the quality of wildlif...

78 FR 42122 - Bridge Builder Trust and Olive Street Investment Advisers, LLC; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-15

... SECURITIES AND EXCHANGE COMMISSION [Investment Company Act Release No. 30592; 812-14118] Bridge...: Bridge Builder Trust (the ``Trust'') and Olive Street Investment Advisers (the ``Adviser'') (collectively... the requested order as a Fund is the Bridge Builder Bond Fund. For purposes of the requested order...

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder took home the Grand Winner prize in the Custom Builder category in the 2014 Housing Innovation Awards for its high performance building science approach. The builder used insulated concrete form blocks to create the insulated crawlspace foundation for its first DOE Zero Energy Ready Home, the first net zero energy new home certified in the state of California.

New Whole-House Solutions Case Study: Shaw Construction, Aspen, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This builder worked with Building Science Corporation to design affordable HERS-54 townhouses with central solar radiator space heating, PV, R-28 closed-cell spray foam under slab and R-26 in advanced framed walls, and rigid polyiso on inside of basement walls

46 CFR 388.4 - Criteria for grant of a waiver.

Code of Federal Regulations, 2010 CFR

2010-10-01

... unduly adversely affect— (i) United States vessel builders; or (ii) The coastwise trade business of any person who employs vessels built in the United States in that business. (2) The determination of “unduly... builders: Whether a potentially affected U.S. vessel builder has a history of construction of similar...

Energy Conservation for the Home Builder: A Course for Residential Builders. Course Outline and Instructional Materials.

ERIC Educational Resources Information Center

Koenigshofer, Daniel R.

Background information, handouts and related instructional materials comprise this manual for conducting a course on energy conservation for home builders. Information presented in the five- and ten-hour course is intended to help residential contractors make appropriate and cost-effective decisions in constructing energy-efficient dwellings.…

DOE Zero Energy Ready Home Case Study, Weiss Building & Development, LLC., System Home, River Forest, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The Passive House Challenge Home located in River Forest, Illinois, is a 5-bedroom, 4.5-bath, 3,600 ft2 two-story home (plus basement) that costs about $237 less per month to operate than a similar sized home built to the 2009 IECC. For a home with no solar photovoltaic panels installed, it scored an amazingly low 27 on the Home Energy Rating System (HERS) score.An ENERGY STAR-rated dishwasher, clothes washer, and refrigerator; an induction cooktop, condensing clothes dryer, and LED lighting are among the energy-saving devices inside the home. All plumbing fixtures comply with EPA WaterSense criteria. The home was awarded a 2013more » Housing Innovation Award in the "systems builder" category.« less

76 FR 19466 - Masco Builder Cabinet Group Including On-Site Leased Workers From Reserves Network, Reliable...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... Builder Cabinet Group Including On-Site Leased Workers From Reserves Network, Reliable Staffing, and Third Dimension Waverly, OH; Masco Builder Cabinet Group Including On-Site Leased Workers From Reserves Network... Group including on-site leased workers from Reserves Network, Jackson, Ohio. The workers produce...

Distributed On-line Monitoring System Based on Modem and Public Phone Net

NASA Astrophysics Data System (ADS)

Chen, Dandan; Zhang, Qiushi; Li, Guiru

In order to solve the monitoring problem of urban sewage disposal, a distributed on-line monitoring system is proposed. By introducing dial-up communication technology based on Modem, the serial communication program can rationally solve the information transmission problem between master station and slave station. The realization of serial communication program is based on the MSComm control of C++ Builder 6.0.The software includes real-time data operation part and history data handling part, which using Microsoft SQL Server 2000 for database, and C++ Builder6.0 for user interface. The monitoring center displays a user interface with alarm information of over-standard data and real-time curve. Practical application shows that the system has successfully accomplished the real-time data acquisition from data gather station, and stored them in the terminal database.

ABodyBuilder: Automated antibody structure prediction with data–driven accuracy estimation

PubMed Central

Leem, Jinwoo; Dunbar, James; Georges, Guy; Shi, Jiye; Deane, Charlotte M.

2016-01-01

ABSTRACT Computational modeling of antibody structures plays a critical role in therapeutic antibody design. Several antibody modeling pipelines exist, but no freely available methods currently model nanobodies, provide estimates of expected model accuracy, or highlight potential issues with the antibody's experimental development. Here, we describe our automated antibody modeling pipeline, ABodyBuilder, designed to overcome these issues. The algorithm itself follows the standard 4 steps of template selection, orientation prediction, complementarity-determining region (CDR) loop modeling, and side chain prediction. ABodyBuilder then annotates the ‘confidence’ of the model as a probability that a component of the antibody (e.g., CDRL3 loop) will be modeled within a root–mean square deviation threshold. It also flags structural motifs on the model that are known to cause issues during in vitro development. ABodyBuilder was tested on 4 separate datasets, including the 11 antibodies from the Antibody Modeling Assessment–II competition. ABodyBuilder builds models that are of similar quality to other methodologies, with sub–Angstrom predictions for the ‘canonical’ CDR loops. Its ability to model nanobodies, and rapidly generate models (∼30 seconds per model) widens its potential usage. ABodyBuilder can also help users in decision–making for the development of novel antibodies because it provides model confidence and potential sequence liabilities. ABodyBuilder is freely available at http://opig.stats.ox.ac.uk/webapps/abodybuilder. PMID:27392298

New Whole-House Solutions Case Study: Hydronic Heating Coil Versus Propane Furnace, Rehoboth Beach, Delaware

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-01-01

In this project involving two homes, the IBACOS team evaluated the performance of the two space conditioning systems and the modeled efficiency of the two tankless domestic hot water systems relative to actual occupant use. Each house was built by Insight Homes and is 1,715-ft2 with a single story, three bedrooms, two bathrooms, and the heating, ventilation, and air conditioning systems and ductwork located in conditioned crawlspaces. The standard house, which the builder offers as its standard production house, uses an air source heat pump (ASHP) with supplemental propane furnace heating. The Building America test house uses the same ASHPmore » unit with supplemental heat provided by the DHW heater (a combined DHW and hydronic heating system, where the hydronic heating element is in the air handler).« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

L. Arena

High-R wall assemblies (R-40 and above) are gaining popularity in the market due to programs like the DOE's Zero Energy Ready Home program, Passive House (PH), Net Zero Energy Home (NZEH) challenges in several states, and highly incentivized retrofit programs. In response to this demand, several builders have successfully used 'double wall' systems to more practically achieve higher R-values in thicker, framed walls. To builders of conventional stick-framed homes, often one of the most appealing features of double wall systems is that there are very few new exterior details. Exterior sheathing, structural bracing, house wrap or building paper, window andmore » door flashing, and siding attachment are usually identical to good details in conventional framed wall systems. The information presented in this guide is intended to reduce the risk of failure in these types of assemblies, increase durability, and result in a reduction of material brought to landfills due to failures and resulting decay. While this document focuses on double wall framing techniques, the majority of the information on how to properly construct and finish high R-value assemblies is applicable to all wall assemblies that do not have foam insulation installed on the exterior of the structural sheathing. The techniques presented have been shown through field studies to reduce the likelihood of mold growth and moisture related damage and are intended for builders, framing contractors, architects, and consultants involved in designing and building super insulated homes.« less

76 FR 13226 - Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-10

... BUILDER CABINET GROUP INCLUDING ON-SITE LEASED WORKERS FROM RESERVES NETWORK AND RELIABLE STAFFING WAVERLY, OHIO. TA-W-71,287B MASCO BUILDER CABINET GROUP INCLUDING ON-SITE LEASED WORKERS FROM RESERVES NETWORK... Builder Cabinet Group, including on-site leased workers from Reserves Network and Reliable Staffing...

77 FR 49003 - Notice of Proposed Information Collection for Public Comment: Request for Acceptance of Changes...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-15

... changes may affect the value shown on the DUD commitment. HUD requires the builder to use form HUD-92577... changes may affect the value shown on the DUD commitment. HUD requires the builder to use form HUD -92577... specifications for proposed construction properties as required by homebuyers or determined by the builder use...

Orion Active Thermal Control System Dynamic Modeling Using Simulink/MATLAB

NASA Technical Reports Server (NTRS)

Wang, Xiao-Yen J.; Yuko, James

2010-01-01

This paper presents dynamic modeling of the crew exploration vehicle (Orion) active thermal control system (ATCS) using Simulink (Simulink, developed by The MathWorks). The model includes major components in ATCS, such as heat exchangers and radiator panels. The mathematical models of the heat exchanger and radiator are described first. Four different orbits were used to validate the radiator model. The current model results were compared with an independent Thermal Desktop (TD) (Thermal Desktop, PC/CAD-based thermal model builder, developed in Cullimore & Ring (C&R) Technologies) model results and showed good agreement for all orbits. In addition, the Orion ATCS performance was presented for three orbits and the current model results were compared with three sets of solutions- FloCAD (FloCAD, PC/CAD-based thermal/fluid model builder, developed in C&R Technologies) model results, SINDA/FLUINT (SINDA/FLUINT, a generalized thermal/fluid network-style solver ) model results, and independent Simulink model results. For each case, the fluid temperatures at every component on both the crew module and service module sides were plotted and compared. The overall agreement is reasonable for all orbits, with similar behavior and trends for the system. Some discrepancies exist because the control algorithm might vary from model to model. Finally, the ATCS performance for a 45-hr nominal mission timeline was simulated to demonstrate the capability of the model. The results show that the ATCS performs as expected and approximately 2.3 lb water was consumed in the sublimator within the 45 hr timeline before Orion docked at the International Space Station.

46 CFR 308.409 - Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 8 2011-10-01 2011-10-01 false Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283. 308.409 Section 308.409 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.409 Standard form...

46 CFR 308.409 - Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 8 2013-10-01 2013-10-01 false Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283. 308.409 Section 308.409 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.409 Standard form...

46 CFR 308.409 - Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283. 308.409 Section 308.409 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.409 Standard form...

46 CFR 308.409 - Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 8 2012-10-01 2012-10-01 false Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283. 308.409 Section 308.409 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.409 Standard form...

46 CFR 308.409 - Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 8 2014-10-01 2014-10-01 false Standard form of War Risk Builder's Risk Insurance Policy, Form MA-283. 308.409 Section 308.409 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.409 Standard form...

PiVoT GPS Receiver

NASA Technical Reports Server (NTRS)

Wennersten, Miriam Dvorak; Banes, Anthony Vince; Boegner, Gregory J.; Dougherty, Lamar; Edwards, Bernard L.; Roman, Joseph; Bauer, Frank H. (Technical Monitor)

2001-01-01

NASA Goddard Space Flight Center has built an open architecture, 24 channel space flight GPS receiver. The CompactPCI PiVoT GPS receiver card is based on the Mitel/GEC Plessey Builder-2 board. PiVoT uses two Plessey 2021 correlators to allow tracking of up to 24 separate GPS SV's on unique channels. Its four front ends can support four independent antennas, making it a useful card for hosting GPS attitude determination algorithms. It has been built using space quality, radiation tolerant parts. The PiVoT card will track a weaker signal than the original Builder 2 board. It also hosts an improved clock oscillator. The PiVoT software is based on the original Plessey Builder 2 software ported to the Linux operating system. The software is POSIX complaint and can easily be converted to other POSIX operating systems. The software is open source to anyone with a licensing agreement with Plessey. Additional tasks can be added to the software to support GPS science experiments or attitude determination algorithms. The next generation PiVoT receiver will be a single radiation hardened CompactPCI card containing the microprocessor and the GPS receiver optimized for use above the GPS constellation. PiVoT was flown successfully on a balloon in July, 2001, for its first non-simulated flight.

A New Event Builder for CMS Run II

NASA Astrophysics Data System (ADS)

Albertsson, K.; Andre, J.-M.; Andronidis, A.; Behrens, U.; Branson, J.; Chaze, O.; Cittolin, S.; Darlea, G.-L.; Deldicque, C.; Dobson, M.; Dupont, A.; Erhan, S.; Gigi, D.; Glege, F.; Gomez-Ceballos, G.; Hegeman, J.; Holzner, A.; Jimenez-Estupiñán, R.; Masetti, L.; Meijers, F.; Meschi, E.; Mommsen, R. K.; Morovic, S.; Nunez-Barranco-Fernandez, C.; O'Dell, V.; Orsini, L.; Paus, C.; Petrucci, A.; Pieri, M.; Racz, A.; Roberts, P.; Sakulin, H.; Schwick, C.; Stieger, B.; Sumorok, K.; Veverka, J.; Zaza, S.; Zejdl, P.

2015-12-01

The data acquisition system (DAQ) of the CMS experiment at the CERN Large Hadron Collider (LHC) assembles events at a rate of 100 kHz, transporting event data at an aggregate throughput of 100GB/s to the high-level trigger (HLT) farm. The DAQ system has been redesigned during the LHC shutdown in 2013/14. The new DAQ architecture is based on state-of-the-art network technologies for the event building. For the data concentration, 10/40 Gbps Ethernet technologies are used together with a reduced TCP/IP protocol implemented in FPGA for a reliable transport between custom electronics and commercial computing hardware. A 56 Gbps Infiniband FDR CLOS network has been chosen for the event builder. This paper discusses the software design, protocols, and optimizations for exploiting the hardware capabilities. We present performance measurements from small-scale prototypes and from the full-scale production system.

A new event builder for CMS Run II

DOE PAGES

Albertsson, K.; Andre, J-M; Andronidis, A.; ...

2015-12-23

The data acquisition system (DAQ) of the CMS experiment at the CERN Large Hadron Collider (LHC) assembles events at a rate of 100 kHz, transporting event data at an aggregate throughput of 100 GB/s to the high-level trigger (HLT) farm. The DAQ system has been redesigned during the LHC shutdown in 2013/14. The new DAQ architecture is based on state-of-the-art network technologies for the event building. For the data concentration, 10/40 Gbps Ethernet technologies are used together with a reduced TCP/IP protocol implemented in FPGA for a reliable transport between custom electronics and commercial computing hardware. A 56 Gbps Innibandmore » FDR CLOS network has been chosen for the event builder. This paper discusses the software design, protocols, and optimizations for exploiting the hardware capabilities. In conclusion, ee present performance measurements from small-scale prototypes and from the full-scale production system.« less

Transforming Junior Leader Development: Developing the Next Generation of Pentathletes

DTIC Science & Technology

2007-12-14

22 and include the strategic leader competency of world-class warrior. Army Leaders serve as a role 69 model, team builder , warrior, influencer... builder ; 4. Upholds the highest standards of duty, honor, integrity, and character. Leadership and learning are indispensable to each other...national goals; c. Innovative thinkers, self-aware, culturally astute, diplomatically aware, and cohesive team builders ; d. Torchbearers of the highest

Business Solutions Case Study: Marketing Zero Energy Homes: LifeStyle Homes, Melbourne, Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Building America research has shown that high-performance homes can potentially give builders an edge in the marketplace and can boost sales. But it doesn't happen automatically. It requires a tailored, easy to understand marketing campaign and sometimes a little flair. This case study highlights LifeStyle Homes’ successful marketing approach for their SunSmart home package, which has helped to boost sales for the company. SunSmart marketing includes a modified logo, weekly blog, social media, traditional advertising, website, and sales staff training. Marketing focuses on quality, durability, healthy indoor air, and energy efficiency with an emphasis on the surety of third-party verificationmore » and the scientific approach to developing the SunSmart package. With the introduction of SunSmart, LifeStyle began an early recovery, nearly doubling sales in 2010; SunSmart sales now exceed 300 homes, including more than 20 zero energy homes. Completed homes in 2014 far outpaced the national (19%) and southern census region (27%) recovery rates for the same period. As technology improves and evolves, this builder will continue to collaborate with Building America.« less

Online Systems for Oversize and Overweight Freight Permitting and Motor Carrier Credentialing : Transportation Research Synthesis.

DOT National Transportation Integrated Search

2017-09-01

MnDOT uses two online systems implemented in the 1990s to issue and manage permits for oversize/overweight (OS/OW) freight and motor carrier credentials: - RouteBuilder, an OS/OW permitting system with a routing component. - Motor Carrier Information...

Comparative Cooling Season Performance of Air Distribution Systems in Multistory Townhomes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poerschke, Andrew; Beach, Rob; Beggs, Timothy

2016-08-01

IBACOS investigated the performance of a small-diameter high velocity heat pump system compared to a conventional system in a new construction triplex townhouse. A ductless heat pump system also was installed for comparison, but the homebuyer backed out because of aesthetic concerns about that system. In total, two buildings, having identical solar orientation and comprised of six townhomes, were monitored for comfort and energy performance. Results show that the small-diameter system provides more uniform temperatures from floor to floor in the three-story townhome. No clear energy consumption benefit was observed from either system. The builder is continuing to explore themore » small-diameter system as its new standard system to provide better comfort and indoor air quality. The homebuilder also explored the possibility of shifting its townhome product to meet the U.S. Department of Energy Challenge Home National Program Requirements. Ultimately, the builder decided that adoption of these practices would be too disruptive midstream in the construction cycle. However, the townhomes met the ENERGY STAR Version 3.0 program requirements.« less

78 FR 44895 - Energy Conservation Program for Consumer Products: First Co. Petition for Reconsideration

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-25

... lead times. Architects, engineers and builders often select HVAC systems for such projects up to 9-12... through the Compliance, Certification Management System (``CCMS'') as part of annual certification... System (``CCMS'') as part of annual certification reporting requirements; and (ii) publish the...

10 CFR 435.304 - The COSTSAFR Program.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) operates on a micro-computer system that uses the MS DOS operating system and is equipped with an 8087 co... (Version 3.0) also prints out a point system that identifies a wide array of different energy conservation... goal and the point system in the design and procurement procedures so that designers and builders can...

10 CFR 435.304 - The COSTSAFR Program.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) operates on a micro-computer system that uses the MS DOS operating system and is equipped with an 8087 co... (Version 3.0) also prints out a point system that identifies a wide array of different energy conservation... goal and the point system in the design and procurement procedures so that designers and builders can...

10 CFR 435.304 - The COSTSAFR Program.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) operates on a micro-computer system that uses the MS DOS operating system and is equipped with an 8087 co... (Version 3.0) also prints out a point system that identifies a wide array of different energy conservation... goal and the point system in the design and procurement procedures so that designers and builders can...

10 CFR 435.304 - The COSTSAFR Program.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) operates on a micro-computer system that uses the MS DOS operating system and is equipped with an 8087 co... (Version 3.0) also prints out a point system that identifies a wide array of different energy conservation... goal and the point system in the design and procurement procedures so that designers and builders can...

10 CFR 435.304 - The COSTSAFR Program.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) operates on a micro-computer system that uses the MS DOS operating system and is equipped with an 8087 co... (Version 3.0) also prints out a point system that identifies a wide array of different energy conservation... goal and the point system in the design and procurement procedures so that designers and builders can...

An empirical analysis of an innovative application for an underutilized resource: small-diameter roundwood in recreational buildings

Treesearch

Randall Cantrell

2004-01-01

Builders were surveyed to explore perceptions regarding small-diameter roundwood (SDR). The study empirically tests a model of builders’ attitudes and opinions about using SDR as a building material in recreational buildings. Findings suggest that, of the 130 builders surveyed, most are likely to use SDR in recreational buildings when it meets the following criteria: 1...

Treating Violence in the School through Traditional Martial Arts

ERIC Educational Resources Information Center

Kim, Israel

2004-01-01

In a comprehensive survey of the literature title "Coping With Violence in the School System," Benbenisti, Astor, and Marachi (2003) map out the programs being deployed throughout the school system today. Those programs listed are "peace builders," "second step," "Richmond's youth against violence,"…

Construction Guidelines for High R-Value Walls without Exterior Rigid Insulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arena, Lois B.

High-R wall assemblies (R-40 and above) are gaining popularity in the market due to programs like the DOE's Zero Energy Ready Home program, Passive House (PH), Net Zero Energy Home (NZEH) challenges in several states, and highly incentivized retrofit programs. In response to this demand, several builders have successfully used 'double wall' systems to more practically achieve higher R-values in thicker, framed walls. To builders of conventional stick-framed homes, often one of the most appealing features of double wall systems is that there are very few new exterior details. Exterior sheathing, structural bracing, house wrap or building paper, window andmore » door flashing, and siding attachment are usually identical to good details in conventional framed wall systems. The information presented in this guide is intended to reduce the risk of failure in these types of assemblies, increase durability, and result in a reduction of material brought to landfills due to failures and resulting decay. While this document focuses on double wall framing techniques, the majority of the information on how to properly construct and finish high R-value assemblies is applicable to all wall assemblies that do not have foam insulation installed on the exterior of the structural sheathing. The techniques presented have been shown through field studies to reduce the likelihood of mold growth and moisture related damage and are intended for builders, framing contractors, architects, and consultants involved in designing and building super insulated homes.« less

Arntz Builders, Inc. Information Sheet

EPA Pesticide Factsheets

Arntz Builders, Inc. (the Company) is located in Novato, California. The settlement involves renovation activities conducted at property constructed prior to 1978, located in San Francisco, California.

Rodan Builders, Inc. Information Sheet

EPA Pesticide Factsheets

Rodan Builders, Inc. (the Company) is located in Burlingame, California. The settlement involves renovation activities conducted at property constructed prior to 1978, located in San Francisco, California.

Steel Band Repertoire: The Case for Original Music

ERIC Educational Resources Information Center

Tanner, Chris

2010-01-01

In the past few decades, the steel band art form has experienced consistent growth and development in several key respects. For example, in the United States, the sheer number of steel band programs has steadily increased, and it appears that this trend will continue in the future. Additionally, pan builders and tuners have made great strides in…

Social Issues and Problem-Based Learning in Sociology: Opportunities and Challenges in the Undergraduate Classroom

ERIC Educational Resources Information Center

Eglitis, Daina S.; Buntman, Fran L.; Alexander, Dameon V.

2016-01-01

This article discusses the use of problem-based learning (PBL) in the undergraduate sociology classroom. PBL shifts students from the role of passive listeners and learners to active knowledge builders and communicators through the use of concise and engaging social problem cases. PBL creates opportunities for building substantive area knowledge,…

DOE Zero Energy Ready Home Case Study: Caldwell and Johnson, Exeter, Rhode Island

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This house, constructed by Caldwell and Johnson, should save its owners $600 per year over the 2009 IECC with the help of efficiency measures such as walls with OSB sheathing and R-13 open cell spray foam insulation. The home garnered a 2013 Housing Innovation Award in the custom builder category.

Muscles, Morals and Mind: Craft Apprenticeship and the Formation of Person

ERIC Educational Resources Information Center

Marchand, Trevor H. J.

2008-01-01

The paper considers apprenticeship as a model of education that both teaches technical skills and provides the grounding for personal formation. The research presented is based on long-term anthropological fieldwork with minaret builders in Yemen, mud masons in Mali and fine-woodwork trainees in London. These case studies of on-site learning and…

The Consortium of Advanced Residential Buildings (CARB) - A Building America Energy Efficient Housing Partnership

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robb Aldrich; Lois Arena; Dianne Griffiths

2010-12-31

This final report summarizes the work conducted by the Consortium of Advanced Residential Buildings (CARB) (http://www.carb-swa.com/), one of the 'Building America Energy Efficient Housing Partnership' Industry Teams, for the period January 1, 2008 to December 31, 2010. The Building America Program (BAP) is part of the Department of Energy (DOE), Energy Efficiency and Renewable Energy, Building Technologies Program (BTP). The long term goal of the BAP is to develop cost effective, production ready systems in five major climate zones that will result in zero energy homes (ZEH) that produce as much energy as they use on an annual basis bymore » 2020. CARB is led by Steven Winter Associates, Inc. with Davis Energy Group, Inc. (DEG), MaGrann Associates, and Johnson Research, LLC as team members. In partnership with our numerous builders and industry partners, work was performed in three primary areas - advanced systems research, prototype home development, and technical support for communities of high performance homes. Our advanced systems research work focuses on developing a better understanding of the installed performance of advanced technology systems when integrated in a whole-house scenario. Technology systems researched included: - High-R Wall Assemblies - Non-Ducted Air-Source Heat Pumps - Low-Load HVAC Systems - Solar Thermal Water Heating - Ventilation Systems - Cold-Climate Ground and Air Source Heat Pumps - Hot/Dry Climate Air-to-Water Heat Pump - Condensing Boilers - Evaporative condensers - Water Heating CARB continued to support several prototype home projects in the design and specification phase. These projects are located in all five program climate regions and most are targeting greater than 50% source energy savings over the Building America Benchmark home. CARB provided technical support and developed builder project case studies to be included in near-term Joule Milestone reports for the following community scale projects: - SBER Overlook at Clipper Mill (mixed, humid climate) - William Ryan Homes - Tampa (hot, humid climate).« less

Charter Schools as Nation Builders: Democracy Prep and Civic Education. Policy Brief 4

ERIC Educational Resources Information Center

Lautzenheiser, Daniel; Kelly, Andrew P.

2013-01-01

This policy brief is the first in a series of in-depth case studies exploring how top-performing charter schools have incorporated civic learning in their school curriculum and school culture. This paper introduces Democracy Prep, a network of seven public charter schools with a civic mission at its core. Democracy Prep's founder and…

USS Cal Builders, Inc. Information Sheet

EPA Pesticide Factsheets

USS Cal Builders, Inc. (the Company) is located in Stanton, California. The settlement involves renovation activities conducted at property constructed prior to 1978, located in San Francisco, California.

[Character accentuations as a criterion for psychological risks in the professional activity of the builders of main gas pipelines in the conditions of arctic].

PubMed

Korneeva, Ia A; Simonova, N N

2015-01-01

The article is devoted to the study of character accentuations as a criterion for psychological risks in the professional activity of builders of main gas pipelines in the conditions of Arctic. to study the severity of character accentuations in rotation-employed builders of main gas pipelines, stipulated by their professional activities, as well as personal resources to overcome these destructions. The study involved 70 rotation-employed builders of trunk pipelines, working in the Tyumen Region (duration of the shift-in--52 days), aged from 23 to 59 (mean age 34,9 ± 8.1) years, with the experience of work from 0.5 years to 14 years (the average length of 4.42 ± 3.1). Methods of the study: questionnaires, psychological testing, participant observation. One-Sample t-test of Student, multiple regression analysis, incremental analysis. In the work there were revealed differences of expression of character accentuations in builders of trunk pipelines with experience in work on rotation less and more than five years. There was determined that builders of the main gas pipelines, working on the rotation in Arctic, with more pronounced accentuation ofthe character use mainly psychological defenses of compensation, substitution and denial, and have an average level of expression of flexibility as the regulatory process.

Scientific customer needs - NASA user

NASA Technical Reports Server (NTRS)

Black, David C.

1987-01-01

Some requirements for scientific users of the Space Station are considered. The use of testbeds to evaluate design concepts for information systems, and for interfacing between designers and builders of systems is examined. The need for an information system that provides an effective interaction between ground-based users and their space-based equipment is discussed.

Aviation Careers Series: Flight Attendants

DOT National Transportation Integrated Search

1996-01-29

Over the past 40 years, the American freight movement system became the envy of the world. Transportation builders, the motor carrier industry, and government regulators have all worked to keep goods moving safely and efficiently. Today freight movem...

Community-Wide Zero Energy Ready Home Standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herk, A.; Beggs, T.

This report outlines the steps a developer can use when looking to create and implement higher performance standards such as the U.S. Department of Energy (DOE) Zero Energy Ready Home (ZERH) standards in a community. The report also describes the specific examples of how this process was followed by a developer, Forest City, in the Stapleton community in Denver, Colorado. IBACOS described the steps used to begin to bring the DOE ZERH standard to the Forest City Stapleton community based on 15 years of community-scale development work done by IBACOS. As a result of this prior IBACOS work, the teammore » gained an understanding of the various components that a master developer needs to consider and created strategies for incorporating those components in the initial phases of development to achieve higher performance buildings in the community. An automated scoring system can be used to perform an internal audit that provides a detailed and consistent evaluation of how several homes under construction or builders' floor plans compare with the requirements of the DOE Zero Energy Ready Home program. This audit can be performed multiple times at specific milestones during construction to allow the builder to make changes as needed throughout construction for the project to meet Zero Energy Ready Home standards. This scoring system also can be used to analyze a builder's current construction practices and design.« less

An Application Programming Interface for Synthetic Snowflake Particle Structure and Scattering Data

NASA Technical Reports Server (NTRS)

Lammers, Matthew; Kuo, Kwo-Sen

2017-01-01

The work by Kuo and colleagues on growing synthetic snowflakes and calculating their single-scattering properties has demonstrated great potential to improve the retrievals of snowfall. To grant colleagues flexible and targeted access to their large collection of sizes and shapes at fifteen (15) microwave frequencies, we have developed a web-based Application Programming Interface (API) integrated with NASA Goddard's Precipitation Processing System (PPS) Group. It is our hope that the API will enable convenient programmatic utilization of the database. To help users better understand the API's capabilities, we have developed an interactive web interface called the OpenSSP API Query Builder, which implements an intuitive system of mechanisms for selecting shapes, sizes, and frequencies to generate queries, with which the API can then extract and return data from the database. The Query Builder also allows for the specification of normalized particle size distributions by setting pertinent parameters, with which the API can also return mean geometric and scattering properties for each size bin. Additionally, the Query Builder interface enables downloading of raw scattering and particle structure data packages. This presentation will describe some of the challenges and successes associated with developing such an API. Examples of its usage will be shown both through downloading output and pulling it into a spreadsheet, as well as querying the API programmatically and working with the output in code.

Building America Case Study: Measure Guideline: Guidance on Taped Insulating Sheathing Drainage Planes (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This guide provides information and recommendations to the following groups: Insulation contractors, General contractors, Builders, Home remodelers, Mechanical contractors, and Homeowners as a guide to the work that needs to be done. The order of work completed during home construction and retrofit improvements is important. Health and safety issues must be addressed first and are more important than durability issues. And durability issues are more important than saving energy. Not all techniques can apply to all houses. Special conditions will require special action. Some builders or homeowners will wish to do more than the important but basic retrofit strategies outlinedmore » by this guide. The following are best practice and product recommendations from the interviewed contractors and home builders who collectively have a vast amount of experience. Three significant items were discussed with the group which are required to make taped insulating sheathing a simple, long term, and durable drainage plane: 4. Horizontal joints should be limited or eliminated wherever possible 5. Where a horizontal joint exists use superior materials 6. Frequent installation inspection and regular trade training are required to maintain proper installation Section 5 of this measure guideline contains the detailed construction procedure for the three recommended methods to effectively seal the joints in exterior insulating sheathing to create a simple, long term, and durable drainage plane.« less

24 CFR 234.1 - Cross-reference.

Code of Federal Regulations, 2011 CFR

2011-04-01

... new construction. 203.14Builders' warranty. 203.18aSolar energy system. 203.18cOne-time or up-front.... 1709) apply to mortgages on individually owned units insured under section 234 of the National Housing...

24 CFR 234.1 - Cross-reference.

Code of Federal Regulations, 2010 CFR

2010-04-01

... new construction. 203.14Builders' warranty. 203.18aSolar energy system. 203.18cOne-time or up-front.... 1709) apply to mortgages on individually owned units insured under section 234 of the National Housing...

24 CFR 257.102 - Cross-reference.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; 203.14 Builder's warranty; 203.16 Certificate and contract regarding use of dwelling for transient or hotel purposes; 203.17(d) Maturity; 203.18 Maximum mortgage amounts; 203.18a Solar-energy system; 203...

24 CFR 257.102 - Cross-reference.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; 203.14 Builder's warranty; 203.16 Certificate and contract regarding use of dwelling for transient or hotel purposes; 203.17(d) Maturity; 203.18 Maximum mortgage amounts; 203.18a Solar-energy system; 203...

24 CFR 257.102 - Cross-reference.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; 203.14 Builder's warranty; 203.16 Certificate and contract regarding use of dwelling for transient or hotel purposes; 203.17(d) Maturity; 203.18 Maximum mortgage amounts; 203.18a Solar-energy system; 203...

24 CFR 257.102 - Cross-reference.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; 203.14 Builder's warranty; 203.16 Certificate and contract regarding use of dwelling for transient or hotel purposes; 203.17(d) Maturity; 203.18 Maximum mortgage amounts; 203.18a Solar-energy system; 203...

24 CFR 257.102 - Cross-reference.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; 203.14 Builder's warranty; 203.16 Certificate and contract regarding use of dwelling for transient or hotel purposes; 203.17(d) Maturity; 203.18 Maximum mortgage amounts; 203.18a Solar-energy system; 203...

Bioconstructor Guild Analysis to Assess Maldivian Reefs Following Ocean Warming and Coral Bleaching

NASA Astrophysics Data System (ADS)

Bianchi, C. N.; Morri, C.; Montefalcone, M.

2016-02-01

Extreme climatic anomalies related to global warming have triggered coral bleaching events across most tropical regions. The hot wave of 1998 El Niño caused mass coral mortality throughout the Indian Ocean. The Maldives has been among the most affected countries, with 60-100% coral mortality reported. Hard coral cover, which dropped to less than 10% after the bleaching, returned to pre-bleaching values of around 50% only by 2014. Between 1997 and 2015, we evaluated the change in cover on Maldivian reef flats of different bioconstructor guilds: i) primary builders are those organisms that build the reef framework and therefore assure reef aggradation; ii) secondary builders provide calcareous material to fill in the frame; iii) binders are encrusters that consolidate the reef edifice; iv) bafflers are soft-bodied algae and colonial invertebrates that, although not actively participating in the bioconstruction, help retaining sediment; v) abiotic attributes (rock, rubble, sand) evidently do not give any contribution to the bioconstruction. A bioconstruction potential index (BCP) was devised using the following formula: BCP = Σin (siCi%) × 100-1where, n is the number of bioconstructor guilds (5, in this case), si is an importance score assigned to the ith guild, and Ci% is the cover of the ith guild. In this study, the value of si has been established at 3 for the primary builders, 2 for the secondary builders, 1 for the binders, 0 for the bafflers, and -1 for the abiotic attributes. Therefore, BCP ranges theoretically from 3, in the unrealistic case of 100% cover by primary constructors, to -1, when only abiotic attributes are present and no bioconstruction is possible, the reef thus being prone to erosion and drowning. When applied to the Maldives data, BCP provided clear threshold values to evaluate constructional capacity. Negative values characterised Maldivian reefs between 1999 and 2003-3007. Values between 0 and 1 depict reefs capable of constratal growth only, and were found 2004-2008 and 2010-2013. Values of BCP greater than 1 are indicative of superstratal growth, and were found in 1997-1998 and again after 2012-2014. Further applications of BCP to other reefs in different regions of the tropical ocean are needed to test how universal this index might be.

Space fabrication demonstration system

NASA Technical Reports Server (NTRS)

1978-01-01

The lower right aluminum beam cap roll forming mill was delivered and installed in the beam builder. The beam was brought to full operational status and beams of one to six bay lengths were produced to demonstrate full system capability. Although the cap flange waviness problem persists, work is progressing within cost and schedule.

Network Systems Technician.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Center on Education and Training for Employment.

This publication contains 17 subjects appropriate for use in a competency list for the occupation of network systems technician, 1 of 12 occupations within the business/computer technologies cluster. Each unit consists of a number of competencies; a list of competency builders is provided for each competency. Titles of the 17 units are as follows:…

RESIDENTIAL VENTILATION STUDY

EPA Science Inventory

This project evaluated the effectiveness, first costs and operational costs of various types of residential ventilation systems in three different climates in the U.S. The Agency, through its Energy Star Program, recommends that builders construct homes that are energy efficient ...

Measure Guideline: Implementing a Plenum Truss for a Compact Air Distribution System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burdick, A.

2013-10-01

This Measure Guideline presents the steps to implement a compact duct system inside an attic bulkhead (plenum truss) of a one-story, slab-on-grade (SOG) home. In a compact duct design, ductwork runs are reduced in length to yield a smaller and more compact duct system. Less energy will be lost through ductwork if the ducts are contained within the thermal enclosure of the house. These measures are intended for the production builder working to meet the 2012 International Energy Conservation Code (IECC) requirements and keep the ductwork within the thermal enclosure of the house. This measure of bringing the heating, ventilationmore » and air conditioning (HVAC) equipment and ductwork within the thermal enclosure of the house is appropriate for the builder wishing to avoid cathedralizing the insulation in the attic space (i.e., locating it at the underside of the roof deck rather than along the attic floor) or adding dropped soffits.« less

Measure Guideline: Implementing a Plenum Truss for a Compact Air Distribution System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burdick, A.

2013-10-01

This Measure Guideline presents the steps to implement a compact duct system inside an attic bulkhead (plenum truss) of a one-story, slab-on-grade home. In a compact duct design, ductwork runs are reduced in length to yield a smaller and more compact duct system. Less energy will be lost through ductwork if the ducts are contained within the thermal enclosure of the house. These measures are intended for the production builder working to meet the 2012 International Energy Conservation Code (IECC) requirements and keep the ductwork within the thermal enclosure of the house. This measure of bringing the heating, ventilation andmore » air conditioning (HVAC) equipment and ductwork within the thermal enclosure of the house is appropriate for the builder wishing to avoid cathedralizing the insulation in the attic space (i.e., locating it at the underside of the roof deck rather than along the attic floor) or adding dropped soffits.« less

The Real Time Display Builder (RTDB)

NASA Technical Reports Server (NTRS)

Kindred, Erick D.; Bailey, Samuel A., Jr.

1989-01-01

The Real Time Display Builder (RTDB) is a prototype interactive graphics tool that builds logic-driven displays. These displays reflect current system status, implement fault detection algorithms in real time, and incorporate the operational knowledge of experienced flight controllers. RTDB utilizes an object-oriented approach that integrates the display symbols with the underlying operational logic. This approach allows the user to specify the screen layout and the driving logic as the display is being built. RTDB is being developed under UNIX in C utilizing the MASSCOMP graphics environment with appropriate functional separation to ease portability to other graphics environments. RTDB grew from the need to develop customized real-time data-driven Space Shuttle systems displays. One display, using initial functionality of the tool, was operational during the orbit phase of STS-26 Discovery. RTDB is being used to produce subsequent displays for the Real Time Data System project currently under development within the Mission Operations Directorate at NASA/JSC. The features of the tool, its current state of development, and its applications are discussed.

Intentional, Inadvertent, or Inevitable? James Burrill Angell and Secularization at the University of Michigan.

ERIC Educational Resources Information Center

Bouman, Jeffrey Paul

The history of James Burrill Angell as the president of the University of Michigan presents a case study of the role of 19th century liberal Protestant university builders in the eventual marginalization of religion from the mainstream of U.S. higher education. Angell's tenure, which began in 1871, encompassed the period in which the modern…

AppBuilder for DSSTools; an application development environment for developing decision support systems in Prolog

Treesearch

Geneho Kim; Donald Nute; H. Michael Rauscher; David L. Loftis

2000-01-01

A programming environment for developing complex decision support systems (DSSs) should support rapid prototyping and modular design, feature a flexible knowledge representation scheme and sound inference mechanisms, provide project management, and be domain independent. We have previously developed DSSTools (Decision Support System Tools), a reusable, domain-...

DOE ZERH Case Study: Mantell-Hecathorn Builders, Shenandoah Circle, Durango, CO

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2015-09-01

Case study of a DOE 2015 Housing Innovation Award winning custom home in the cold climate that got a HERS 50 without PV, or HERS 21 with PV, with 2x6 24” on center walls with R-13 ccsf plus 3.5” blown fiberglass, plus R-10 rigid exterior; R-22 ICF basement walls; vented attic with spray foam over top plates, R-65 blown fiberglass; 96 AFUE furnace, triple-pane windows, 80% LED.

DOE ZERH Case Study: New Town Builders, Town Homes at Perrin's Row, Wheat Ridge, CO

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2015-09-01

Case study of a DOE 2015 Housing Innovation Award winning multifamily project with 26 units in the cold climate that got a HERS 54 without PV, or HERS 28 with PV, with 2x6 24” on center walls with R-23 blown fiberglass; slab foundation with R-10 rigid at slab edge; plus R-10 rigid exterior; R-22 ICF basement walls; vented attic with R-50 blown fiberglass; 92 AFUE furnace, 13 SEER AC.

Between the Under-Labourer and the Master-Builder: Observations on Bunge's Method

ERIC Educational Resources Information Center

Agassi, Joseph

2012-01-01

Mario Bunge has repeatedly discussed contributions to philosophy and to science that are worthless at best and dangerous at worst, especially cases of pseudo-science. He clearly gives his reason in his latest essay on this matter: "The fact that science can be faked to the point of deceiving science lovers suggests the need for a rigorous sifting…

Building America Industrialized Housing Partnership (BAIHP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

McIlvaine, Janet; Chandra, Subrato; Barkaszi, Stephen

This final report summarizes the work conducted by the Building America Industrialized Housing Partnership (www.baihp.org) for the period 9/1/99-6/30/06. BAIHP is led by the Florida Solar Energy Center of the University of Central Florida and focuses on factory built housing. In partnership with over 50 factory and site builders, work was performed in two main areas--research and technical assistance. In the research area--through site visits in over 75 problem homes, we discovered the prime causes of moisture problems in some manufactured homes and our industry partners adopted our solutions to nearly eliminate this vexing problem. Through testing conducted in overmore » two dozen housing factories of six factory builders we documented the value of leak free duct design and construction which was embraced by our industry partners and implemented in all the thousands of homes they built. Through laboratory test facilities and measurements in real homes we documented the merits of 'cool roof' technologies and developed an innovative night sky radiative cooling concept currently being tested. We patented an energy efficient condenser fan design, documented energy efficient home retrofit strategies after hurricane damage, developed improved specifications for federal procurement for future temporary housing, compared the Building America benchmark to HERS Index and IECC 2006, developed a toolkit for improving the accuracy and speed of benchmark calculations, monitored the field performance of over a dozen prototype homes and initiated research on the effectiveness of occupancy feedback in reducing household energy use. In the technical assistance area we provided systems engineering analysis, conducted training, testing and commissioning that have resulted in over 128,000 factory built and over 5,000 site built homes which are saving their owners over $17,000,000 annually in energy bills. These include homes built by Palm Harbor Homes, Fleetwood, Southern Energy Homes, Cavalier and the manufacturers participating in the Northwest Energy Efficient Manufactured Home program. We worked with over two dozen Habitat for Humanity affiliates and helped them build over 700 Energy Star or near Energy Star homes. We have provided technical assistance to several show homes constructed for the International builders show in Orlando, FL and assisted with other prototype homes in cold climates that save 40% over the benchmark reference. In the Gainesville Fl area we have several builders that are consistently producing 15 to 30 homes per month in several subdivisions that meet the 30% benchmark savings goal. We have contributed to the 2006 DOE Joule goals by providing two community case studies meeting the 30% benchmark goal in marine climates.« less

Automated 3D Damaged Cavity Model Builder for Lower Surface Acreage Tile on Orbiter

NASA Technical Reports Server (NTRS)

Belknap, Shannon; Zhang, Michael

2013-01-01

The 3D Automated Thermal Tool for Damaged Acreage Tile Math Model builder was developed to perform quickly and accurately 3D thermal analyses on damaged lower surface acreage tiles and structures beneath the damaged locations on a Space Shuttle Orbiter. The 3D model builder created both TRASYS geometric math models (GMMs) and SINDA thermal math models (TMMs) to simulate an idealized damaged cavity in the damaged tile(s). The GMMs are processed in TRASYS to generate radiation conductors between the surfaces in the cavity. The radiation conductors are inserted into the TMMs, which are processed in SINDA to generate temperature histories for all of the nodes on each layer of the TMM. The invention allows a thermal analyst to create quickly and accurately a 3D model of a damaged lower surface tile on the orbiter. The 3D model builder can generate a GMM and the correspond ing TMM in one or two minutes, with the damaged cavity included in the tile material. A separate program creates a configuration file, which would take a couple of minutes to edit. This configuration file is read by the model builder program to determine the location of the damage, the correct tile type, tile thickness, structure thickness, and SIP thickness of the damage, so that the model builder program can build an accurate model at the specified location. Once the models are built, they are processed by the TRASYS and SINDA.

Kotai Antibody Builder: automated high-resolution structural modeling of antibodies.

PubMed

Yamashita, Kazuo; Ikeda, Kazuyoshi; Amada, Karlou; Liang, Shide; Tsuchiya, Yuko; Nakamura, Haruki; Shirai, Hiroki; Standley, Daron M

2014-11-15

Kotai Antibody Builder is a Web service for tertiary structural modeling of antibody variable regions. It consists of three main steps: hybrid template selection by sequence alignment and canonical rules, 3D rendering of alignments and CDR-H3 loop modeling. For the last step, in addition to rule-based heuristics used to build the initial model, a refinement option is available that uses fragment assembly followed by knowledge-based scoring. Using targets from the Second Antibody Modeling Assessment, we demonstrate that Kotai Antibody Builder generates models with an overall accuracy equal to that of the best-performing semi-automated predictors using expert knowledge. Kotai Antibody Builder is available at http://kotaiab.org standley@ifrec.osaka-u.ac.jp. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

James Williamson d/b/a Golden Triangle Builders Information Sheet

EPA Pesticide Factsheets

James Williamson d/b/a Golden Triangle Builders (the Company) is located in Pittsburgh, Pennsylvania. The settlement involves renovation activities conducted at property constructed prior to 1978, located in Pittsburgh, Pennsylvania.

The Misuse of Anabolic-Androgenic Steroids among Iranian Recreational Male Body-Builders and Their Related Psycho-Socio-Demographic factors

PubMed Central

ANGOORANI, Hooman; HALABCHI, Farzin

2015-01-01

Background: The high prevalence and potential side effects of anabolic-androgenic steroids (AAS) misuse by athletes has made it a major public health concern. Epidemiological studies on the abuse of such drugs are mandatory for developing effective preventive drug control programs in sports community. This study aimed to investigate the prevalence of AAS abuse and their association with some psycho-socio-demographic factors in Iranian male recreational body-builders. Methods: Between March and October 2011; 906 recreational male body-builders from 103 randomly selected bodybuilding clubs in Tehran, Iran were participated in this study. Some psycho-socio- demographic factors including age, job, average family income, family size, sport experience (months), weekly duration of the sporting activity (h), purpose of participation in sporting activity, mental health as well as body image (via General Health Questionnaire and Multidimensional Body-Self Relations Questionnaire, respectively), and history of AAS use were obtained by interviews using questionnaires. Results: Participants were all recreational male body-builders [mean age (SD): 25.7 (7.1), ranging 14–56 yr]. Self-report of AAS abuse was registered in 150 body-builders (16.6%). Among different psycho-socio-demographic factors, only family income and sport experience were inversely associated with AAS abuse. Conclusion: Lifetime prevalence of AAS abuse is relatively high among recreational body-builders based on their self-report. Some psycho-socio-demographic factors including family income and sport experience may influence the prevalence of AAS abuse. PMID:26811817

The Misuse of Anabolic-Androgenic Steroids among Iranian Recreational Male Body-Builders and Their Related Psycho-Socio-Demographic factors.

PubMed

Angoorani, Hooman; Halabchi, Farzin

2015-12-01

The high prevalence and potential side effects of anabolic-androgenic steroids (AAS) misuse by athletes has made it a major public health concern. Epidemiological studies on the abuse of such drugs are mandatory for developing effective preventive drug control programs in sports community. This study aimed to investigate the prevalence of AAS abuse and their association with some psycho-socio-demographic factors in Iranian male recreational body-builders. Between March and October 2011; 906 recreational male body-builders from 103 randomly selected bodybuilding clubs in Tehran, Iran were participated in this study. Some psycho-socio- demographic factors including age, job, average family income, family size, sport experience (months), weekly duration of the sporting activity (h), purpose of participation in sporting activity, mental health as well as body image (via General Health Questionnaire and Multidimensional Body-Self Relations Questionnaire, respectively), and history of AAS use were obtained by interviews using questionnaires. Participants were all recreational male body-builders [mean age (SD): 25.7 (7.1), ranging 14-56 yr]. Self-report of AAS abuse was registered in 150 body-builders (16.6%). Among different psycho-socio-demographic factors, only family income and sport experience were inversely associated with AAS abuse. Lifetime prevalence of AAS abuse is relatively high among recreational body-builders based on their self-report. Some psycho-socio-demographic factors including family income and sport experience may influence the prevalence of AAS abuse.

Lost in translation? A multilingual Query Builder improves the quality of PubMed queries: a randomised controlled trial.

PubMed

Schuers, Matthieu; Joulakian, Mher; Kerdelhué, Gaetan; Segas, Léa; Grosjean, Julien; Darmoni, Stéfan J; Griffon, Nicolas

2017-07-03

MEDLINE is the most widely used medical bibliographic database in the world. Most of its citations are in English and this can be an obstacle for some researchers to access the information the database contains. We created a multilingual query builder to facilitate access to the PubMed subset using a language other than English. The aim of our study was to assess the impact of this multilingual query builder on the quality of PubMed queries for non-native English speaking physicians and medical researchers. A randomised controlled study was conducted among French speaking general practice residents. We designed a multi-lingual query builder to facilitate information retrieval, based on available MeSH translations and providing users with both an interface and a controlled vocabulary in their own language. Participating residents were randomly allocated either the French or the English version of the query builder. They were asked to translate 12 short medical questions into MeSH queries. The main outcome was the quality of the query. Two librarians blind to the arm independently evaluated each query, using a modified published classification that differentiated eight types of errors. Twenty residents used the French version of the query builder and 22 used the English version. 492 queries were analysed. There were significantly more perfect queries in the French group vs. the English group (respectively 37.9% vs. 17.9%; p < 0.01). It took significantly more time for the members of the English group than the members of the French group to build each query, respectively 194 sec vs. 128 sec; p < 0.01. This multi-lingual query builder is an effective tool to improve the quality of PubMed queries in particular for researchers whose first language is not English.

Advanced GIS Exercise: Performing Error Analysis in ArcGIS ModelBuilder

ERIC Educational Resources Information Center

Hall, Steven T.; Post, Christopher J.

2009-01-01

Knowledge of Geographic Information Systems is quickly becoming an integral part of the natural resource professionals' skill set. With the growing need of professionals with these skills, we created an advanced geographic information systems (GIS) exercise for students at Clemson University to introduce them to the concept of error analysis,…

15. Detail view of Boston Bridge Works builders plate, north ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. Detail view of Boston Bridge Works builders plate, north portal brace, looking southwest - India Point Railroad Bridge, Spanning Seekonk River between Providence & East Providence, Providence, Providence County, RI

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

?Ducts in conditioned space (DCS) represent a high priority measure for moving the next generation of new homes to the Zero Net Energy performance level. Various strategies exist for incorporating ducts within the conditioned thermal envelope. To support this activity, in 2013 the Pacific Gas & Electric Company initiated a project with Davis Energy Group (lead for the Building America team, Alliance for Residential Building Innovation) to solicit builder involvement in California to participate in field demonstrations of various DCS strategies. Builders were given incentives and design support in exchange for providing site access for construction observation, diagnostic testing, andmore » builder survey feedback. Information from the project was designed to feed into California's 2016 Title 24 process, but also to serve as an initial mechanism to engage builders in more high performance construction strategies. This Building America project complemented information collected in the California project with BEopt simulations of DCS performance in hot/dry climate regions.« less

Building America Best Practices Series Volume 12: Builders Challenge Guide to 40% Whole-House Energy Savings in the Cold and Very Cold Climates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-02-01

This best practices guide is the twelfth in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the cold and very cold climates can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. Themore » best practices described in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and thos erequirements are highlighted in the text. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

DOE Zero Energy Ready Home Case Study: Palo Duro Homes — Palo Duro Homes, Albuquerque, NM

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-09-01

This builder was honored for Most DOE Zero Energy Ready Homes Built in the 2014 Housing Innovation Awards. By July 2014, Palo Duro had completed 152 homes since the program began in 2013 (under the original program title DOE Challenge Home), all of them certified to the stringent efficiency requirements of DOE’s Zero Energy Ready Home program.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springer, David; German, Alea

Building cost-effective, high-performance homes that provide superior comfort, health, and durability is the goal of the U.S. Department of Energy’s (DOE’s) Zero Energy Ready Home (ZERH) program. Building America research and other innovative programs throughout the country have addressed many of the technical challenges of building to the ZERH standard. The cost-effectiveness of measure packages that result in 30% source energy savings compared to a code-compliant home have been demonstrated. However, additional challenges remain, particularly with respect to convincing production builders of the strong business case for ZERH. The Alliance for Residential Building Innovation (ARBI) team believes that the keysmore » to successfully engaging builders and developers in the California market are to help them leverage development agreement requirements, code compliance requirements, incentives, and competitive market advantages of ZERH certification, and navigate through this process. A primary objective of this project was to gain a highly visible foothold for residential buildings that are built to the DOE ZERH specification that can be used to encourage participation by other California builders. This report briefly describes two single-family homes that were ZERH certified and focuses on the experience of working with developer Mutual Housing on a 62-unit multifamily community at the Spring Lake subdivision in Woodland, California. The Spring Lake project is expected to be the first ZERH-certified multifamily project in the country. This report discusses the challenges encountered, lessons learned, and how obstacles were overcome.« less

Polycyclic aromatic hydrocarbon exposure and burden of outdoor workers in Budapest.

PubMed

Szaniszló, J; Ungváry, G

2001-03-09

Polycyclic aromatic hydrocarbons exposure (PAHs: (benz[a]anthracene, benzo[a]pyrene, dibenz[a,h]anthracene, benzo[b]fluoranthene, benzo[k]fluoranthene, indeno[1,2,3-cd]-pyrene, fluoranthene, chrysene, pyrene) of policemen on street duty in downtown Budapest and workers repairing the road (asphalting) at a traffic junction and their excretion of PAH metabolites (1-hydroxypyrene, 3-hydroxybenz[a]anthracene, and 3-hydroxybenzo[a]pyrene) were determined. As controls, health-care workers were investigated. In addition PAH pollution of the air of a factory processing asphalt was also measured. The measurements were performed on air samples gained using personal samplers and from urine of end-shift samples using a high-performance liquid chromatography method. It was found that PAH pollution of the most crowded and busy center of Budapest was similar to that of several other cities in the world. PAH exposure of road builders was actually not higher than that of policemen; the slight difference resulted from diverging life-styles. PAH metabolite excretion of smoking health-care workers, road builders, or policemen significantly exceeded that of the nonsmokers. The PAH metabolite values of the three groups engaged in various activities did not show any difference. It was concluded that cancer-related risk due to PAH compounds in the case of policemen on street duty and road builders (asphalting) does not exceed significantly that of workers not exposed occupationally to PAHs in the ambient air, but that smoking is a decisive factor.

Evolving paradigm of illnesses presented to medical Intensive Care Unit in body builders: Cases from tertiary care center.

PubMed

Garg, Sunil Kumar

2015-04-01

Bodybuilding is the use of progressive resistance exercise to control and develop one's musculature. With the rise in number of persons adopting this activity, there is evolving paradigm of illnesses presented to intensive care in this population subset. Strict adherence to details of bodybuilding and avoidance of unsupervised medications are essential to prevent untoward effects.

Evolving paradigm of illnesses presented to medical Intensive Care Unit in body builders: Cases from tertiary care center

PubMed Central

Garg, Sunil Kumar

2015-01-01

Bodybuilding is the use of progressive resistance exercise to control and develop one's musculature. With the rise in number of persons adopting this activity, there is evolving paradigm of illnesses presented to intensive care in this population subset. Strict adherence to details of bodybuilding and avoidance of unsupervised medications are essential to prevent untoward effects. PMID:25878431

Ecocity mapping using GIS: introducing a planning method for assessing and improving neighborhood vitality.

PubMed

Smith, Richard; Miller, Kirstin

2013-01-01

Assessing neighborhood vitality is important to understanding how to improve quality of life and health outcomes. The ecocity model recognizes that cities are part of natural systems and favors walkable neighborhoods. This article introduces ecocity mapping, an innovative planning method, to the public health literature on community engagement by describing a pilot project with a new affordable housing development in Oakland, California between 2007 and 2009. Although ecocity mapping began as a paper technology, advances in geographic information systems (GIS) moved it forward. This article describes how Ecocity Builders used GIS to conduct ecocity mapping to (1) assess vitality of neighborhoods and urban centers to prioritize community health intervention pilot sites and (2) create scenario maps for use in community health planning. From fall 2007 to summer 2008, Ecocity Builders assessed neighborhood vitality using walking distance from parks, schools, rapid transit stops, grocery stores, and retail outlets. In 2008, ecocity maps were shared with residents to create a neighborhood health and sustainability plan. In 2009, Ecocity Builders developed scenario maps to show how changes to the built environment would improve air quality by reducing greenhouse gas emissions from vehicles, while increasing access to basic services and natural amenities. Community organizing with GIS was more useful than GIS alone for final site selection. GIS was useful in mapping scenarios after residents shared local neighborhood knowledge and ideas for change. Residents were interested in long-term environmental planning, provided they could meet immediate needs.

Solar Heating and Cooling of Residential Buildings: Sizing, Installation and Operation of Systems.

ERIC Educational Resources Information Center

Colorado State Univ., Ft. Collins. Solar Energy Applications Lab.

This training course and a companion course titled "Design of Systems for Solar Heating and Cooling of Residential Buildings," are designed to train home designers and builders in the fundamentals of solar hydronic and air systems for space heating and cooling and domestic hot water heating for residential buildings. Each course, organized in 22…

Graphical user interfaces for symbol-oriented database visualization and interaction

NASA Astrophysics Data System (ADS)

Brinkschulte, Uwe; Siormanolakis, Marios; Vogelsang, Holger

1997-04-01

In this approach, two basic services designed for the engineering of computer based systems are combined: a symbol-oriented man-machine-service and a high speed database-service. The man-machine service is used to build graphical user interfaces (GUIs) for the database service; these interfaces are stored using the database service. The idea is to create a GUI-builder and a GUI-manager for the database service based upon the man-machine service using the concept of symbols. With user-definable and predefined symbols, database contents can be visualized and manipulated in a very flexible and intuitive way. Using the GUI-builder and GUI-manager, a user can build and operate its own graphical user interface for a given database according to its needs without writing a single line of code.

System diagnostic builder: a rule-generation tool for expert systems that do intelligent data evaluation

NASA Astrophysics Data System (ADS)

Nieten, Joseph L.; Burke, Roger

1993-03-01

The system diagnostic builder (SDB) is an automated knowledge acquisition tool using state- of-the-art artificial intelligence (AI) technologies. The SDB uses an inductive machine learning technique to generate rules from data sets that are classified by a subject matter expert (SME). Thus, data is captured from the subject system, classified by an expert, and used to drive the rule generation process. These rule-bases are used to represent the observable behavior of the subject system, and to represent knowledge about this system. The rule-bases can be used in any knowledge based system which monitors or controls a physical system or simulation. The SDB has demonstrated the utility of using inductive machine learning technology to generate reliable knowledge bases. In fact, we have discovered that the knowledge captured by the SDB can be used in any number of applications. For example, the knowledge bases captured from the SMS can be used as black box simulations by intelligent computer aided training devices. We can also use the SDB to construct knowledge bases for the process control industry, such as chemical production, or oil and gas production. These knowledge bases can be used in automated advisory systems to ensure safety, productivity, and consistency.

Space fabrication demonstration system. [beam builder and induction fastening

NASA Technical Reports Server (NTRS)

1980-01-01

The development effort on the composite beam cap fabricator was completed within cost and close to abbreviated goals. The design and analysis of flight weight primary and secondary beam builder structures proceeded satisfactorily but remains curtailed until further funding is made available to complete the work. The induction fastening effort remains within cost and schedule constraints. Tests of the LARC prototype induction welder is continuing in an instrumented test stand comprised of a Dumore drill press (air over oil feed for variable applied loads) and a dynamometer to measure actual welding loads. Continued testing shows that the interface screening must be well impregnated with resin to ensure proper flow when bonding graphite-acrylic lap shear samples. Specimens prepared from 0.030 inch thick graphite-polyethersulfone are also available for future induction fastening evaluation.

49 CFR 179.220-25 - Stamping.

Code of Federal Regulations, 2010 CFR

2010-10-01

...: Material ASTM A240-316L. Shell thickness Shell 0.167 in. Head thickness Head 0.150 in. Tank builders initials ABC. Date of original test 00-0000. Outer shell: Material ASTM A285-C. Tank builders initials WYZ...

6. BUILDER'S PLATE ON WEST TRUSS: 'MOSELEY IRON BUILDING WORKS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. BUILDER'S PLATE ON WEST TRUSS: 'MOSELEY IRON BUILDING WORKS, BOSTON 1888, PATENTED 1881 TO T.W.E. MOSELEY' - Upper Pacific Mills Bridge, Moved to Merrimack College, North Andover, MA, Lawrence, Essex County, MA

18. Castiron bridge plate citing builder, date, and names of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. Cast-iron bridge plate citing builder, date, and names of bridge committee members. Jack Boucher, photographer, 1977 - Neshanic Station Lenticular Truss Bridge, State Route 567, spanning South Branch of Raritan River, Neshanic Station, Somerset County, NJ

Building America Residential System Research Results: Achieving 30% Whole House Energy Savings Level in Mixed-Humid Climates; January 2006 - December 2006

DOE Office of Scientific and Technical Information (OSTI.GOV)

Building America Industrialized Housing Partnership; Building Industry Research Alliance; Building Science Consortium

2006-12-01

The Building America program conducts the system research required to reduce risks associated with the design and construction of homes that use an average of 30% to 90% less total energy for all residential energy uses than the Building America Research Benchmark, including research on homes that will use zero net energy on annual basis. To measure the program's progress, annual research milestones have been established for five major climate regions in the United States. The system research activities required to reach each milestone take from 3 to 5 years to complete and include research in individual test houses, studiesmore » in pre-production prototypes, and research studies with lead builders that provide early examples that the specified energy savings level can be successfully achieved on a production basis. This report summarizes research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Mixed-Humid Climate Region on a cost-neutral basis.« less

Polyol and Amino Acid-Based Biosurfactants, Builders, and Hydrogels

USDA-ARS?s Scientific Manuscript database

This chapter reviews different detergent materials which have been synthesized from natural agricultural commodities. Background information, which gives reasons why the use of biobased materials may be advantageous, is presented. Detergent builders from L-aspartic acid, citric acid and D-sorbitol...

Installing an Integrated System and a Fourth-Generation Language.

ERIC Educational Resources Information Center

Ridenour, David; Ferguson, Linda

1987-01-01

In the spring of 1986 Indiana State University converted to the Series Z software of Information Associates, an IBM mainframe, and Information Builders' FOCUS fourth-generation language. The beginning of the planning stage to product selection, training, and implementation is described. (Author/MLW)

Building Community through Mentoring Adult Learners

ERIC Educational Resources Information Center

Plante, Jarrad; Truitt, Joshua

2016-01-01

The Volunteer UCF Community Connectors and Community Builders Program provides a connection between students and their community. The goal is to develop meaningful service opportunities for UCF students that contribute measurable results and systemic change through capacity building among adult learners. The ongoing, sustainable service experience…

Radiometric Measurement Comparisons Using Transfer Radiometers in Support of the Calibration of NASA's Earth Observing System (EOS) Sensors

NASA Technical Reports Server (NTRS)

Butler, James J.; Johnson, B. Carol; Brown, Steven W.; Yoon, Howard W.; Barnes, Robert A.; Markham, Brian L.; Biggar, Stuart F.; Zalewski, Edward F.; Spyak, Paul R.; Cooper, John W.;

Building America Residential System Research Results: Achieving 30% Whole House Energy Savings Level in Mixed-Humid Climates; January 2006 - December 2006

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R.; Hendron, R.; Eastment, M.

2006-12-01

This report summarizes research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Mixed-Humid Climate Region on a cost-neutral basis.

Conditioning of sewage sludge by Fenton's reagent combined with skeleton builders.

PubMed

Liu, Huan; Yang, Jiakuan; Shi, Yafei; Li, Ye; He, Shu; Yang, Changzhu; Yao, Hong

2012-06-01

Physical conditioners, often known as skeleton builders, are commonly used to improve the dewaterability of sewage sludge. This study evaluated a novel joint usage of Fenton's reagent and skeleton builders, referred to as the F-S inorganic composite conditioner, focusing on their efficacies and the optimization of the major operational parameters. The results demonstrate that the F-S composite conditioner for conditioning sewage sludge is a viable alternative to conventional organic polymers, especially when ordinary Portland cement (OPC) and lime are used as the skeleton builders. Experimental investigations confirmed that Fenton reaction required sufficient time (80 min in this study) to degrade organics in the sludge. The optimal condition of this process was at pH=5, Fe(2+)=40 mg g(-1) (dry solids), H(2)O(2)=32 mg g(-1), OPC=300 mg g(-1) and lime=400 mg g(-1), in which the specific resistance to filtration reduction efficiency of 95% was achieved. Copyright © 2012 Elsevier Ltd. All rights reserved.

49 CFR 230.47 - Boiler number.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Steam Gauges § 230.47 Boiler number. (a) Generally. The builder's number of the boiler, if known, shall be stamped on the steam dome or manhole flange. If the builder's number cannot be obtained, an...

Building v/s Exploring Models: Comparing Learning of Evolutionary Processes through Agent-based Modeling

NASA Astrophysics Data System (ADS)

Wagh, Aditi

Two strands of work motivate the three studies in this dissertation. Evolutionary change can be viewed as a computational complex system in which a small set of rules operating at the individual level result in different population level outcomes under different conditions. Extensive research has documented students' difficulties with learning about evolutionary change (Rosengren et al., 2012), particularly in terms of levels slippage (Wilensky & Resnick, 1999). Second, though building and using computational models is becoming increasingly common in K-12 science education, we know little about how these two modalities compare. This dissertation adopts agent-based modeling as a representational system to compare these modalities in the conceptual context of micro-evolutionary processes. Drawing on interviews, Study 1 examines middle-school students' productive ways of reasoning about micro-evolutionary processes to find that the specific framing of traits plays a key role in whether slippage explanations are cued. Study 2, which was conducted in 2 schools with about 150 students, forms the crux of the dissertation. It compares learning processes and outcomes when students build their own models or explore a pre-built model. Analysis of Camtasia videos of student pairs reveals that builders' and explorers' ways of accessing rules, and sense-making of observed trends are of a different character. Builders notice rules through available blocks-based primitives, often bypassing their enactment while explorers attend to rules primarily through the enactment. Moreover, builders' sense-making of observed trends is more rule-driven while explorers' is more enactment-driven. Pre and posttests reveal that builders manifest a greater facility with accessing rules, providing explanations manifesting targeted assembly. Explorers use rules to construct explanations manifesting non-targeted assembly. Interviews reveal varying degrees of shifts away from slippage in both modalities, with students who built models not incorporating slippage explanations in responses. Study 3 compares these modalities with a control using traditional activities. Pre and posttests reveal that the two modalities manifested greater facility with accessing and assembling rules than the control. The dissertation offers implications for the design of learning environments for evolutionary change, design of the two modalities based on their strengths and weaknesses, and teacher training for the same.

High Performance Builder Spotlight: Treasure Homes Inc.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2011-01-01

Treasure Homes, Inc., achieved a HERS rating of 46 without PV on its prototype “Gem” home, located on the shores of Lake Michigan in northern Indiana, thanks in part to training received from a Building America partner, the National Association of Home Builders Research Center.

BRIDGE BUILDER WILLIAM FLINN’S “CAMP & BRIDGE BUILDING OUTFIT”. INTERIOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

BRIDGE BUILDER WILLIAM FLINN’S “CAMP & BRIDGE BUILDING OUTFIT”. INTERIOR VIEW SHOWING LABORERS AT MEAL TIME. - Clear Fork of Brazos River Suspension Bridge, Spanning Clear Fork of Brazos River at County Route 179, Albany, Shackelford County, TX

DETAIL OF CORNERSTONE, WHICH STATES "J.J. DANIELS, BUILDER 1861." NOTE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF CORNERSTONE, WHICH STATES "J.J. DANIELS, BUILDER 1861." NOTE ALSO IRON STRAP AT EAST CORNER OF ABUTMENT. - Jackson Covered Bridge, Spanning Sugar Creek, CR 775N (Changed from Spanning Sugar Creek), Bloomingdale, Parke County, IN

Building Green the Right Way

ERIC Educational Resources Information Center

Lewis, C. Deana

2009-01-01

As the workforce development arm of the National Association of Home Builders (NAHB), and cluster leader for the Architecture and Construction career cluster, Home Builders Institute (HBI) has a vested interest in keeping America's elementary, middle and high school students excited and knowledgeable about what's new in residential construction.…

NREL: News - 15 Home Builders Earn Energyvalue Awards

Science.gov Websites

builders who voluntarily integrate energy and resource efficiency into the design, construction and successful approaches to resource-efficient construction. The 2002 EVHA winners are: Tierra Concrete Homes , Sioux City, IA Artistic Homes, Albuquerque, NM Chuck Miller Construction, Hidden Springs ID Enviro

Annual Performance Evaluation of a Pair of Energy Efficient Houses (WC3 and WC4) in Oak Ridge, TN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; Christian, Jeffrey E; Gehl, Anthony C

2012-04-01

Beginning in 2008, two pairs of energy-saver houses were built at Wolf Creek in Oak Ridge, TN. These houses were designed to maximize energy efficiency using new ultra-high-efficiency components emerging from ORNL s Cooperative Research and Development Agreement (CRADA) partners and others. The first two houses contained 3713 square feet of conditioned area and were designated as WC1 and WC2; the second pair consisted of 2721 square feet conditioned area with crawlspace foundation and they re called WC3 and WC4. This report is focused on the annual energy performance of WC3 and WC4, and how they compare against a previouslymore » benchmarked maximum energy efficient house of a similar footprint. WC3 and WC4 are both about 55-60% more efficient than traditional new construction. Each house showcases a different envelope system: WC3 is built with advanced framing featured cellulose insulation partially mixed with phase change materials (PCM); and WC4 house has cladding composed of an exterior insulation and finish system (EIFS). The previously benchmarked house was one of three built at the Campbell Creek subdivision in Knoxville, TN. This house (CC3) was designed as a transformation of a builder house (CC1) with the most advanced energy-efficiency features, including solar electricity and hot water, which market conditions are likely to permit within the 2012 2015 period. The builder house itself was representative of a standard, IECC 2006 code-certified, all-electric house built by the builder to sell around 2005 2008.« less

The XSD-Builder Specification Language—Toward a Semantic View of XML Schema Definition

NASA Astrophysics Data System (ADS)

Fong, Joseph; Cheung, San Kuen

In the present database market, XML database model is a main structure for the forthcoming database system in the Internet environment. As a conceptual schema of XML database, XML Model has its limitation on presenting its data semantics. System analyst has no toolset for modeling and analyzing XML system. We apply XML Tree Model (shown in Figure 2) as a conceptual schema of XML database to model and analyze the structure of an XML database. It is important not only for visualizing, specifying, and documenting structural models, but also for constructing executable systems. The tree model represents inter-relationship among elements inside different logical schema such as XML Schema Definition (XSD), DTD, Schematron, XDR, SOX, and DSD (shown in Figure 1, an explanation of the terms in the figure are shown in Table 1). The XSD-Builder consists of XML Tree Model, source language, translator, and XSD. The source language is called XSD-Source which is mainly for providing an environment with concept of user friendliness while writing an XSD. The source language will consequently be translated by XSD-Translator. Output of XSD-Translator is an XSD which is our target and is called as an object language.

Database interfaces on NASA's heterogeneous distributed database system

NASA Technical Reports Server (NTRS)

Huang, Shou-Hsuan Stephen

1989-01-01

The syntax and semantics of all commands used in the template are described. Template builders should consult this document for proper commands in the template. Previous documents (Semiannual reports) described other aspects of this project. Appendix 1 contains all substituting commands used in the system. Appendix 2 includes all repeating commands. Appendix 3 is a collection of DEFINE templates from eight different DBMS's.

Army Communicator. Volume 36, Number 4, Winter 2011

DTIC Science & Technology

2011-01-01

Association for Home Builders . Prior to becoming the command sergeant major of the Army Communications- Electronics Life Cycle Management...development of future senior civilian IT leaders. He headed the Army’s functional civilian personnel system for IT for his entire senior...pride in Functional Area 53 – Information Systems Management, I have to respectfully disagree with his characterization of Functional Area 57

Analysis of Navy Flight Scheduling Methods Using FlyAwake

DTIC Science & Technology

2009-09-01

28 Figure 4. FlyAwake Schedule Builder Screenshot..........................................................28...Figure 5. FlyAwake Work Schedule Builder Screenshot................................................29 Figure 6. FlyAwake Graphical Output Screenshot... disqualifies crewmembers from participating in the following day’s flight operations. These rules are subject to operational requirements and deviation

The Functional Measurement Experiment Builder suite: two Java-based programs to generate and run functional measurement experiments.

PubMed

Mairesse, Olivier; Hofmans, Joeri; Theuns, Peter

2008-05-01

We propose a free, easy-to-use computer program that does not requires prior knowledge of computer programming to generate and run experiments using textual or pictorial stimuli. Although the FM Experiment Builder suite was initially programmed for building and conducting FM experiments, it can also be applied for non-FM experiments that necessitate randomized, single, or multifactorial designs. The program is highly configurable, allowing multilingual use and a wide range of different response formats. The outputs of the experiments are Microsoft Excel compatible .xls files that allow easy copy-paste of the results into Weiss's FM CalSTAT program (2006) or any other statistical package. Its Java-based structure is compatible with both Windows and Macintosh operating systems, and its compactness (< 1 MB) makes it easily distributable over the Internet.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers remove the protective cover from NASA’s MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers remove the protective cover from NASA’s MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

SDMProjectBuilder: SWAT Setup for Nutrient Fate and Transport

EPA Science Inventory

This tutorial reviews some of the screens, icons, and basic functions of the SDMProjectBuilder (SDMPB) and explains how one uses SDMPB output to populate the Soil and Water Assessment Tool (SWAT) input files for nutrient fate and transport modeling in the Salt River Basin. It dem...

49 CFR 230.47 - Boiler number.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Boiler number. 230.47 Section 230.47... Steam Gauges § 230.47 Boiler number. (a) Generally. The builder's number of the boiler, if known, shall be stamped on the steam dome or manhole flange. If the builder's number cannot be obtained, an...

49 CFR 230.47 - Boiler number.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Boiler number. 230.47 Section 230.47... Steam Gauges § 230.47 Boiler number. (a) Generally. The builder's number of the boiler, if known, shall be stamped on the steam dome or manhole flange. If the builder's number cannot be obtained, an...

49 CFR 230.47 - Boiler number.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Boiler number. 230.47 Section 230.47... Steam Gauges § 230.47 Boiler number. (a) Generally. The builder's number of the boiler, if known, shall be stamped on the steam dome or manhole flange. If the builder's number cannot be obtained, an...

49 CFR 230.47 - Boiler number.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Boiler number. 230.47 Section 230.47... Steam Gauges § 230.47 Boiler number. (a) Generally. The builder's number of the boiler, if known, shall be stamped on the steam dome or manhole flange. If the builder's number cannot be obtained, an...

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, NASA’s MESSENGER spacecraft is secure after transfer to the work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, NASA’s MESSENGER spacecraft is secure after transfer to the work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, NASA’s MESSENGER spacecraft is lifted off the pallet for transfer to a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, NASA’s MESSENGER spacecraft is lifted off the pallet for transfer to a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, workers check the placement of NASA’s MESSENGER spacecraft on a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, workers check the placement of NASA’s MESSENGER spacecraft on a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, NASA’s MESSENGER spacecraft is revealed. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, NASA’s MESSENGER spacecraft is revealed. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers move NASA’s MESSENGER spacecraft into a high bay clean room. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers move NASA’s MESSENGER spacecraft into a high bay clean room. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, an overhead crane moves NASA’s MESSENGER spacecraft toward a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, an overhead crane moves NASA’s MESSENGER spacecraft toward a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, an overhead crane lowers NASA’s MESSENGER spacecraft onto a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities, an overhead crane lowers NASA’s MESSENGER spacecraft onto a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Antiterrorism Measures For Historic Properties

DTIC Science & Technology

2006-09-01

steel jacket on an existing concrete column (Morley Builders 1997...of the material. Figure 17. Seismic application of a steel jacket on an existing concrete column (Morley Builders 1997). Columns — Reinforced...from a previously unreinforced structure, so future irreversibility of the technique need not disqualify it from consideration by project teams. ERDC

Counselors as Esteem Builders.

ERIC Educational Resources Information Center

Santa Rita, Emilio, Jr.

This paper contains an instrument for evaluating college counselors as esteem-builders, using Borba's Analysis of Self-Esteem. The instrument is divided into five components, each of which should be fostered in a student by the counselor: (1) Security, a feeling of strong assuredness; (2) Selfhood, a feeling of individuality; (3) Affiliation, a…

ED-WAVE tool design approach: Case of a textile wastewater treatment plant in Blantyre, Malawi

NASA Astrophysics Data System (ADS)

Chipofya, V.; Kraslawski, A.; Avramenko, Y.

The ED-WAVE tool is a PC based package for imparting training on wastewater treatment technologies. The system consists of four modules viz. Reference Library, Process Builder, Case Study Manager, and Treatment Adviser. The principles of case-based design and case-based reasoning as applied in the ED-WAVE tool are utilised in this paper to evaluate the design approach of the wastewater treatment plant at Mapeto David Whitehead & Sons (MDW&S) textile and garments factory, Blantyre, Malawi. The case being compared with MDW&S in the ED-WAVE tool is Textile Case 4 in Sri Lanka (2003). Equalisation, coagulation and rotating biological contactors is the sequencing of treatment units at Textile Case 4 in Sri Lanka. Screening, oxidation ditches and sedimentation is the sequencing of treatment units at MDW&S textile and garments factory. The study suggests that aerobic biological treatment is necessary in the treatment of wastewater from a textile and garments factory. MDW&S incorporates a sedimentation process which is necessary for the removal of settleable matter before the effluent is discharged to the municipal wastewater treatment plant. The study confirmed the practical use of the ED-WAVE tool in the design of wastewater treatment systems, where after encountering a new situation; already collected decision scenarios (cases) are invoked and modified in order to arrive at a particular design alternative. What is necessary, however, is to appropriately modify the case arrived at through the Case Study Manager in order to come up with a design appropriate to the local situation taking into account technical, socio-economic and environmental aspects.

Simulation Modeling of Advanced Pilot Training: The Effects of a New Aircraft Family of Systems

DTIC Science & Technology

2014-03-01

baseline requirements disqualifies itself from further consideration. The next phase of competition involves adjusting the total proposed price by...submodels, the previous submodel provided the framework for the following submodel. This copy-and-paste process forced the model builder to inspect each

Housing Modifications for Persons Who Are Blind or Visually Impaired.

ERIC Educational Resources Information Center

Cocke, Elizabeth A.

1992-01-01

This paper outlines housing modification issues for both the housing consumer with visual impairments and the builder/remodeler, with emphasis on single-family housing. Suggested modifications are listed for the exterior, entrance, elevator, doors, floors, lighting and the electrical system, windows, room layout and shape, kitchen, and stairs and…

Technology Solutions Case Study: Capillary Break Beneath a Slab: Polyethylene Sheeting over Aggregate, Southwestern Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-07-01

In this project, Building America team IBACOS worked with a builder of single- and multifamily homes in southwestern Pennsylvania (climate zone 5) to understand its methods of successfully using polyethylene sheeting over aggregate as a capillary break beneath the slab in new construction. This builder’s homes vary in terms of whether they have crawlspaces or basements. However, in both cases, the strategy protects the home from water intrusion via capillary action (e.g., water wicking into cracks and spaces in the slab), thereby helping to preserve the durability of the home.

CNC Turning Technician. A Competency-Based Instructional System.

ERIC Educational Resources Information Center

Sloan, Kelly; Hilley, Robert

This competency-based curriculum guide for instructing students in using computer numerically controlled (CNC) turning machines is one of a series of instructional guides for the machinist field developed in Oklahoma. Although developed jointly with Baxter Technologies Corporation and oriented toward the Baxter Vo-Tec 2000 Future Builder CNC…

Operationalizing Special Operations Aviation in Indonesia

DTIC Science & Technology

2006-12-15

special operations forces Builder: Lockheed Power Plant: Four Allison T56 -A-15 turboprop engines Thrust: 4,910 shaft horsepower each engine...Builder: Lockheed Power Plant: Four Allison T56 -A-15 turboprop engines Thrust: 4,910 shaft horsepower each engine Length: 98 feet, 9 inches (30.09

Best Practices Case Study: David Weekley Homes - Eagle Springs and Waterhaven, Houston, TX

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2011-04-01

Case study describing David Weekley Homes, Houston Division, has qualified more than 1,240 homes for the DOE Builders Challenge. Advanced framed 2x6 walls with open headers and two-stud corners allow more room for R-20 damp sprayed cellulose wall cavity insulation that is covered with R-5 rigid XPS foam. A radiant barrier cuts heat gain in the R-38 insulated vented attics. Draft stopping at fireplace and duct chases and behind tubs, gluing sheetrock to framing, and extensive caulking make for air-tight homes at 3.0 ACH50.

Space Construction Automated Fabrication Experiment Definition Study. (SCAFEDS), part 3. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

A range of tasks focused on a baseline system concept is discussed. A beam builder concept developed to produce a triangular beam is discussed. Beam elements used laminated graphite and glass composite strip material with external surface coatings are described.

Industry Talks the Talk and Walks the Walk

ERIC Educational Resources Information Center

Lewis, C. Deanna

2008-01-01

Home Builders Institute (HBI), the workforce development arm of the National Association of Home Builders (NAHB), is dedicated to the advancement and enrichment of education and training programs serving the needs of the building industry. For more than 30 years, HBI has trained skilled workers in residential construction, promoted the industry as…

The Columbia-Willamette Skill Builders Consortium. Final Performance Report.

ERIC Educational Resources Information Center

Portland Community Coll., OR.

The Columbia-Willamette Skill Builders Consortium was formed in early 1988 in response to a growing awareness of the need for improved workplace literacy training and coordinated service delivery in Northwest Oregon. In June 1990, the consortium received a National Workplace Literacy Program grant to develop and demonstrate such training. The…

Captivate MenuBuilder: Creating an Online Tutorial for Teaching Software

ERIC Educational Resources Information Center

Yelinek, Kathryn; Tarnowski, Lynn; Hannon, Patricia; Oliver, Susan

2008-01-01

In this article, the authors, students in an instructional technology graduate course, describe a process to create an online tutorial for teaching software. They created the tutorial for a cyber school's use. Five tutorial modules were linked together through one menu screen using the MenuBuilder feature in the Adobe Captivate program. The…

13 CFR 120.391 - What is the Builders Loan Program?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What is the Builders Loan Program? 120.391 Section 120.391 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...)(9) of the Act, SBA may make or guarantee loans to finance small general contractors to construct or...

13 CFR 120.391 - What is the Builders Loan Program?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false What is the Builders Loan Program? 120.391 Section 120.391 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...)(9) of the Act, SBA may make or guarantee loans to finance small general contractors to construct or...

13 CFR 120.391 - What is the Builders Loan Program?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 13 Business Credit and Assistance 1 2012-01-01 2012-01-01 false What is the Builders Loan Program? 120.391 Section 120.391 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...)(9) of the Act, SBA may make or guarantee loans to finance small general contractors to construct or...

13 CFR 120.391 - What is the Builders Loan Program?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false What is the Builders Loan Program? 120.391 Section 120.391 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...)(9) of the Act, SBA may make or guarantee loans to finance small general contractors to construct or...

13 CFR 120.391 - What is the Builders Loan Program?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false What is the Builders Loan Program? 120.391 Section 120.391 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...)(9) of the Act, SBA may make or guarantee loans to finance small general contractors to construct or...

Carbonate Production by Benthic Communities on Shallow Coralgal Reefs of Abrolhos Bank, Brazil.

PubMed

Reis, Vanessa Moura Dos; Karez, Cláudia Santiago; Mariath, Rodrigo; de Moraes, Fernando Coreixas; de Carvalho, Rodrigo Tomazetto; Brasileiro, Poliana Silva; Bahia, Ricardo da Gama; Lotufo, Tito Monteiro da Cruz; Ramalho, Laís Vieira; de Moura, Rodrigo Leão; Francini-Filho, Ronaldo Bastos; Pereira-Filho, Guilherme Henrique; Thompson, Fabiano Lopes; Bastos, Alex Cardoso; Salgado, Leonardo Tavares; Amado-Filho, Gilberto Menezes

2016-01-01

The abundance of reef builders, non-builders and the calcium carbonate produced by communities established in Calcification Accretion Units (CAUs) were determined in three Abrolhos Bank shallow reefs during the period from 2012 to 2014. In addition, the seawater temperature, the irradiance, and the amount and composition of the sediments were determined. The inner and outer reef arcs were compared. CAUs located on the inner reef shelf were under the influence of terrigenous sediments. On the outer reefs, the sediments were composed primarily of marine biogenic carbonates. The mean carbonate production in shallow reefs of Abrolhos was 579 ± 98 g m-2 y-1. The builder community was dominated by crustose coralline algae, while the non-builder community was dominated by turf. A marine heat wave was detected during the summer of 2013-2014, and the number of consecutive days with a temperature above or below the summer mean was positively correlated with the turf cover increase. The mean carbonate production of the shallow reefs of Abrolhos Bank was greater than the estimated carbonate production measured for artificial structures on several other shallow reefs of the world. The calcimass was higher than the non-calcareous mass, suggesting that the Abrolhos reefs are still in a positive carbonate production balance. Given that marine heat waves produce an increase of turf cover on the shallow reefs of the Abrolhos, a decrease in the cover represented by reef builders and shifting carbonate production are expected in the near future.

Carbonate Production by Benthic Communities on Shallow Coralgal Reefs of Abrolhos Bank, Brazil

PubMed Central

dos Reis, Vanessa Moura; Karez, Cláudia Santiago; Mariath, Rodrigo; de Moraes, Fernando Coreixas; de Carvalho, Rodrigo Tomazetto; Brasileiro, Poliana Silva; Bahia, Ricardo da Gama; Lotufo, Tito Monteiro da Cruz; Ramalho, Laís Vieira; de Moura, Rodrigo Leão; Francini-Filho, Ronaldo Bastos; Pereira-Filho, Guilherme Henrique; Thompson, Fabiano Lopes; Bastos, Alex Cardoso; Salgado, Leonardo Tavares; Amado-Filho, Gilberto Menezes

2016-01-01

The abundance of reef builders, non-builders and the calcium carbonate produced by communities established in Calcification Accretion Units (CAUs) were determined in three Abrolhos Bank shallow reefs during the period from 2012 to 2014. In addition, the seawater temperature, the irradiance, and the amount and composition of the sediments were determined. The inner and outer reef arcs were compared. CAUs located on the inner reef shelf were under the influence of terrigenous sediments. On the outer reefs, the sediments were composed primarily of marine biogenic carbonates. The mean carbonate production in shallow reefs of Abrolhos was 579 ± 98 g m-2 y-1. The builder community was dominated by crustose coralline algae, while the non-builder community was dominated by turf. A marine heat wave was detected during the summer of 2013–2014, and the number of consecutive days with a temperature above or below the summer mean was positively correlated with the turf cover increase. The mean carbonate production of the shallow reefs of Abrolhos Bank was greater than the estimated carbonate production measured for artificial structures on several other shallow reefs of the world. The calcimass was higher than the non-calcareous mass, suggesting that the Abrolhos reefs are still in a positive carbonate production balance. Given that marine heat waves produce an increase of turf cover on the shallow reefs of the Abrolhos, a decrease in the cover represented by reef builders and shifting carbonate production are expected in the near future. PMID:27119151

Space fabrication demonstration system, technical volume

NASA Technical Reports Server (NTRS)

1979-01-01

The automatic beam builder ABB was developed, fabricated, and demonstrated within the established contract cost and schedule constraints. The ABB demonstrated the feasibility of: producing lightweight beams automatically within the required rate of 1 to 5 ft of completed beam per minute and producing structurally sound beams with axial design load of 5538 N based on the Grumman photovoltaic satellite solar power system design reference structure.

46 CFR 69.105 - Application for measurement services.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place and year built. (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for...

46 CFR 69.105 - Application for measurement services.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place and year built. (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for...

46 CFR 69.105 - Application for measurement services.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place and year built. (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for...

46 CFR 69.105 - Application for measurement services.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place and year built. (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for...

46 CFR 69.105 - Application for measurement services.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Type of vessel. (b) Vessel's name and official number (if assigned). (c) Builder's name and the vessel hull number assigned by the builder. (d) Place and year built. (e) Date keel was laid. (f) Overall length, breadth, and depth of vessel. (g) Lines plan. (h) Booklet of offsets. (i) Capacity plans for...

Space Fabrication Demonstration System

NASA Technical Reports Server (NTRS)

1977-01-01

Progress on fabrication facility (beam builder) support structure control, clamp/weld block, and welding and truss cut off is discussed. The brace attachment design was changed and the design of the weld mechanism was modified which achieved the following system benefits: (1) simplified weld electrode life; (2) reduced weld power requirements; and (3) simplified brace attachment mechanisms. Static and fatigue characteristics of spot welded 2024T3 aluminum joints are evaluated.

13 CFR 120.392 - Who may apply?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 13 Business Credit and Assistance 1 2012-01-01 2012-01-01 false Who may apply? 120.392 Section 120.392 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.392 Who may apply? A construction contractor or home-builder with a past...

13 CFR 120.392 - Who may apply?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false Who may apply? 120.392 Section 120.392 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.392 Who may apply? A construction contractor or home-builder with a past...

13 CFR 120.392 - Who may apply?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false Who may apply? 120.392 Section 120.392 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.392 Who may apply? A construction contractor or home-builder with a past...

13 CFR 120.392 - Who may apply?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Who may apply? 120.392 Section 120.392 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Special Purpose Loans Builders Loan Program § 120.392 Who may apply? A construction contractor or home-builder with a past...

A PCIe Gen3 based readout for the LHCb upgrade

NASA Astrophysics Data System (ADS)

Bellato, M.; Collazuol, G.; D'Antone, I.; Durante, P.; Galli, D.; Jost, B.; Lax, I.; Liu, G.; Marconi, U.; Neufeld, N.; Schwemmer, R.; Vagnoni, V.

2014-06-01

The architecture of the data acquisition system foreseen for the LHCb upgrade, to be installed by 2018, is devised to readout events trigger-less, synchronously with the LHC bunch crossing rate at 40 MHz. Within this approach the readout boards act as a bridge between the front-end electronics and the High Level Trigger (HLT) computing farm. The baseline design for the LHCb readout is an ATCA board requiring dedicated crates. A local area standard network protocol is implemented in the on-board FPGAs to read out the data. The alternative solution proposed here consists in building the readout boards as PCIe peripherals of the event-builder servers. The main architectural advantage is that protocol and link-technology of the event-builder can be left open until very late, to profit from the most cost-effective industry technology available at the time of the LHC LS2.

Validation of Radiometric Standards for the Laboratory Calibration of Reflected-Solar Earth Observing Satellite Instruments

NASA Technical Reports Server (NTRS)

Butler, James J.; Johnson, B. Carol; Rice, Joseph P.; Brown, Steven W.; Barnes, Robert A.

2007-01-01

Historically, the traceability of the laboratory calibration of Earth-observing satellite instruments to a primary radiometric reference scale (SI units) is the responsibility of each instrument builder. For the NASA Earth Observing System (EOS), a program has been developed using laboratory transfer radiometers, each with its own traceability to the primary radiance scale of a national metrology laboratory, to independently validate the radiances assigned to the laboratory sources of the instrument builders. The EOS Project Science Office also developed a validation program for the measurement of onboard diffuse reflecting plaques, which are also used as radiometric standards for Earth-observing satellite instruments. Summarized results of these validation campaigns, with an emphasis on the current state-of-the-art uncertainties in laboratory radiometric standards, will be presented. Future mission uncertainty requirements, and possible enhancements to the EOS validation program to ensure that those uncertainties can be met, will be presented.

77 FR 47861 - Notice of Submission of Proposed Information Collection to OMB Hispanic-Serving Institutions...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-10

... construction properties as required by homebuyers or determined by the builder use the information collection. The lender reviews the changes and amends the approved exhibits. These changes ma affect the value shown on the DUD commitment. HUD requires the builder to use form HUD-92577 to request changes for...

Modeling Code Is Helping Cleveland Develop New Products

NASA Technical Reports Server (NTRS)

1998-01-01

Master Builders, Inc., is a 350-person company in Cleveland, Ohio, that develops and markets specialty chemicals for the construction industry. Developing new products involves creating many potential samples and running numerous tests to characterize the samples' performance. Company engineers enlisted NASA's help to replace cumbersome physical testing with computer modeling of the samples' behavior. Since the NASA Lewis Research Center's Structures Division develops mathematical models and associated computation tools to analyze the deformation and failure of composite materials, its researchers began a two-phase effort to modify Lewis' Integrated Composite Analyzer (ICAN) software for Master Builders' use. Phase I has been completed, and Master Builders is pleased with the results. The company is now working to begin implementation of Phase II.

Quantitative Microbial Risk Assessment Tutorial - SDMProjectBuilder: Import Local Data Files to Identify and Modify Contamination Sources and Input ParametersUpdated 2017

EPA Science Inventory

Twelve example local data support files are automatically downloaded when the SDMProjectBuilder is installed on a computer. They allow the user to modify values to parameters that impact the release, migration, fate, and transport of microbes within a watershed, and control delin...

Quantitative Microbial Risk Assessment Tutorial – SDMProjectBuilder: Import Local Data Files to Identify and Modify Contamination Sources and Input Parameters

EPA Science Inventory

Twelve example local data support files are automatically downloaded when the SDMProjectBuilder is installed on a computer. They allow the user to modify values to parameters that impact the release, migration, fate, and transport of microbes within a watershed, and control delin...

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

By working with builder partners on test homes, researchers from the U.S. Department of Energy’s Building America program can vet whole-house building strategies and avoid potential unintended consequences of implementing untested solution packages on a production scale. To support this research, Building America team Consortium for Advanced Residential Buildings (CARB) partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, Connecticut. The philosophy and science behind the 2,700 ft2 “Performance House” was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adaptable to the needs of homeowners. The technologies and strategies usedmore » in the “Performance House” were best practices rather than cutting edge, with a focus on simplicity in construction, maintenance, and operation. Achieving 30% source energy savings compared with a home built to the 2009 International Energy Conservation Code in the cold climate zone requires that nearly all components and systems be optimized. Careful planning and design are critical. The end result was a DOE Challenge Home that achieved a Home Energy Rating System (HERS) Index Score of 20 (43 without photovoltaics [PV]).« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

By working with builder partners on test homes, researchers from the U.S. Department of Energy's Building America program can vet whole-house building strategies and avoid potential unintended consequences of implementing untested solution packages on a production scale. To support this research, Building America team Consortium for Advanced Residential Buildings (CARB) partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, Connecticut. The philosophy and science behind the 2,700 ft2 "Performance House" was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adaptable to the needs of homeowners. The technologies and strategies usedmore » in the "Performance House" were best practices rather than cutting edge, with a focus on simplicity in construction, maintenance, and operation. Achieving 30% source energy savings compared with a home built to the 2009 International Energy Conservation Code in the cold climate zone requires that nearly all components and systems be optimized. Careful planning and design are critical. The end result was a DOE Challenge Home that achieved a Home Energy Rating System (HERS) Index Score of 20 (43 without photovoltaics [PV]).« less

The Electronic Lumberyard and Builders' Rights: Technology, Copyrights, Patents, and Academe.

ERIC Educational Resources Information Center

Fisher, Francis Dummer

1989-01-01

The legal system of copyright may have worked in the era of print, but with electronic technology, society needs less encumbered and cheaper access to expressed ideas. Economic success will go to those nations that best succeed in promoting creativity without inhibiting the incorporation of expressed ideas into other products. (MLW)

Market segmentation and analysis of Japan's residential post and beam construction market.

Treesearch

Joseph A. Roos; Ivan L. Eastin; Hisaaki Matsuguma

2005-01-01

A mail survey of Japanese post and beam builders was conducted to measure their level of ethnocentrism, market orientation, risk aversion, and price consciousness. The data were analyzed utilizing factor and cluster analysis. The results showed that Japanese post and beam builders can be divided into three distinct market segments: open to import...

The Power of Professional Capital: With an Investment in Collaboration, Teachers Become Nation Builders

ERIC Educational Resources Information Center

Hargreaves, Andrew; Fullan, Michael

2013-01-01

This article explores the powerful idea of capital and articulates its importance for professional work, professional capacity, and professional effectiveness. Systems that invest in professional capital recognize that education spending is an investment in developing human capital from early childhood to adulthood, leading to rewards of economic…

Using Sustainable Development as a Competitive Strategy

NASA Astrophysics Data System (ADS)

Spearman, Pat

Sustainable development reduces construction waste by 43%, generating 50% cost savings. Residential construction executives lacking adequate knowledge regarding the benefits of sustainable development practices are at a competitive disadvantage. Drawing from the diffusion of innovation theory, the purpose of this qualitative case study was to explore knowledge acquisition within the bounds of sustainable residential construction. The purposive sample size of 11 executive decision makers fulfilled the sample size requirements and enabled the extraction of meaningful data. Participants were members of the National Home Builders Association and had experience of a minimum of 5 years in residential construction. The research question addressed how to improve knowledge acquisition relating to the cost benefits of building green homes and increase the adoption rate of sustainable development among residential builders. Data were collected via semistructured telephone interviews, field observation, and document analysis. Transcribed data were validated via respondent validation, coded into 5 initial categories aligned to the focus of the research, then reduced to 3 interlocking themes of environment, competitive advantage, and marketing. Recommendations include developing comprehensive public policies, horizontal and vertical communications networks, and green banks to capitalize sustainable development programs to improve the diffusion of green innovation as a competitive advantage strategy. Business leaders could benefit from this data by integrating sustainable development practices into their business processes. Sustainable development reduces operational costs, increases competitive advantage for builders, and reduces greenhouse gas emissions. Implications for social change increase energy independence through conservation and developing a legislative policy template for comprehensive energy strategies. A comprehensive energy strategy promotes economic development, technological gains in all business sectors within the energy industry, and reduces energy costs for consumers.

The BELLE DAQ system

NASA Astrophysics Data System (ADS)

Suzuki, Soh Yamagata; Yamauchi, Masanori; Nakao, Mikihiko; Itoh, Ryosuke; Fujii, Hirofumi

2000-10-01

We built a data acquisition system for the BELLE experiment. The system was designed to cope with the average trigger rate up to 500 Hz at the typical event size of 30 kB. This system has five components: (1) the readout sequence controller, (2) the FASTBUS-TDC readout systems using charge-to-time conversion, (3) the barrel shifter event builder, (4) the parallel online computing farm, and (5) the data transfer system to the mass storage. This system has been in operation for physics data taking since June 1999 without serious problems.

Catalog of components for electric and hybrid vehicle propulsion systems

NASA Technical Reports Server (NTRS)

Eissler, H. C.

1981-01-01

This catalog of commercially available electric and hybrid vehicle propulsion system components is intended for designers and builders of these vehicles and contains 50 categories of components. These categories include those components used between the battery terminals and the output axle hub, as well as some auxiliary equipment. An index of the components and a listing of the suppliers and their addresses and phone numbers are included.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers get ready to remove the protective cover from NASA’s MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers get ready to remove the protective cover from NASA’s MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare NASA’s MESSENGER spacecraft for transfer to a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare NASA’s MESSENGER spacecraft for transfer to a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers begin moving NASA’s MESSENGER spacecraft into the building MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - is being taken into a high bay clean room where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers begin moving NASA’s MESSENGER spacecraft into the building MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - is being taken into a high bay clean room where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, a lift begins lowering NASA’s MESSENGER spacecraft onto the ground. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, a lift begins lowering NASA’s MESSENGER spacecraft onto the ground. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers check the moveable pallet holding NASA’s MESSENGER spacecraft. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, workers check the moveable pallet holding NASA’s MESSENGER spacecraft. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Compact Buried Ducts in a Hot-Humid Climate House

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, D.

2016-01-01

A system of compact, buried ducts provides a high-performance and cost-effective solution for delivering conditioned air throughout the building. This report outlines research activities that are expected to facilitate adoption of compact buried duct systems by builders. The results of this research would be scalable to many new house designs in most climates and markets, leading to wider industry acceptance and building code and energy program approval.

Citizens Utilities Company's successful residential new construction market transformation program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caulfield, T.O.; Shepherd, M.A.

1998-07-01

Citizens Utilities Company, Arizona Electric Division (CUC/AED) fielded a Residential New Construction Program (RNC) in the forth quarter of 1994 that had been designed from conception as a market transformation program. The CUC RNC Program encouraged builders to adopt energy efficient building practices for new homes by supplying builders estimates of energy savings, supplying inspections services to assist builders in applying energy efficient building practices while verifying compliance, and posting and promoting the home as energy efficient during the sales period. Measures generally required to qualify for the program were R-38 ceiling insulation, R-21 wall insulation, polysealing of all infiltrationmore » gaps during construction, well sealed air-conditioning ducts, and an air conditioner Seasonal Energy Efficiency Rating (SEER) of 11.0 or greater. In less than two years the program achieved over 17% market penetration without offering rebates to builders. This paper reviews the design of the program, including a discussion of the features felt to be primarily responsible for its success. It reviews the levels of penetration achieved, free-ridership, spillover, and market barriers encountered. Finally it proposes improvements to the program designed to carry it the next step toward a self-sustaining market transformation program.« less

75 FR 14487 - Requested Administrative Waiver of the Coastwise Trade Laws

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-25

... for the vessel CLOUD NINE. SUMMARY: As authorized by 46 U.S.C. 12121, the Secretary of Transportation... . Interested parties may comment on the effect this action may have on U.S. vessel builders or businesses in... have an unduly adverse effect on a U.S.-vessel builder or a business that uses U.S.-flag vessels in...

ScholarshipBuilder Program, Second Annual Report 1989-1990. Report No. 10, Vol. 25.

ERIC Educational Resources Information Center

Ruffin, Minnie R.; And Others

The ScholarshipBuilder Program, an adopt-a-class program, began in November 1988 to encourage selected first-grade students to stay in school until graduation in the year 2000. Scholarships will be provided by Merrill Lynch, Incorporated, for students who go on to college, and a one-time stipend will be provided to students who enter the military…

75 FR 34528 - Requested Administrative Waiver of the Coastwise Trade Laws

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-17

... comment on the effect this action may have on U.S. vessel builders or businesses in the U.S. that use U.S... effect on a U.S.-vessel builder or a business that uses U.S.-flag vessels in that business, a waiver will... vessel ERIC K is: Intended Commercial Use of Vessel: ``Charter and teaching trawler skills.'' Geographic...

Coronary calcification in body builders using anabolic steroids.

PubMed

Santora, Lawrence J; Marin, Jairo; Vangrow, Jack; Minegar, Craig; Robinson, Mary; Mora, Janet; Friede, Gerald

2006-01-01

The authors measured coronary artery calcification as a means of examining the impact of anabolic steroids on the development of atherosclerotic disease in body builders using anabolic steroids over an extended period of time. Fourteen male professional body builders with no history of cardiovascular disease were evaluated for coronary artery calcium, serum lipids, left ventricular function, and exercise-induced myocardial ischemia. Seven subjects had coronary artery calcium, with a much higher than expected mean score of 98. Six of the 7 calcium scores were >90th percentile. Mean total cholesterol was 192 mg/dL, while mean high-density lipoprotein was 23 mg/dL and the mean ratio of total cholesterol to high-density lipoprotein was 8.3. Left ventricular ejection fraction ranged between 49% and 68%, with a mean of 59%. No subject had evidence of myocardial ischemia. This small group of professional body builders with a long history of steroid abuse had high levels of coronary artery calcium for age. The authors conclude that in this small pilot study there is an association between early coronary artery calcium and long-term steroid abuse. Large-scale studies are warranted to further explore this association.

Safe, Seen, and Celebrated with AHA! Peace Builders: Putting Youth in Charge of Change

ERIC Educational Resources Information Center

Freed, Jennifer; Lowenstein, Melissa

2017-01-01

Since 2013, AHA! (Attitude. Harmony. Achievement) has trained over 300 AHA! Peace Builder youth at six area schools in Santa Barbara, California. These young people have conducted outreach to more than 5,000 additional peers, family members, and community members via Connection Circles, which they led during class, between classes, at AHA! Peace…

77 FR 42258 - Notice of Funding Availability (NOFA) of Applications for Section 514 Farm Labor Housing Loans...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-18

... Home Builders (NAHB) ICC 700-2008 National Green Building Standard TM: http://www.nahb.org . --Bronze...://www1.eere.energy.gov/builders/challenge/ and Participation in local green/energy efficient building..., Green Communities, LEED for Homes or NAHB's National Green Building Standard (ICC-700) 2008, receive at...

Builder 3 & 2. Naval Education and Training Command Rate Training Manual and Nonresident Career Course. Revised.

ERIC Educational Resources Information Center

Countryman, Gene L.

This Rate Training Manual (Textbook) and Nonresident Career Course form a correspondence, self-study package to provide information related to tasks assigned to Builders Third and Second Class. Focus is on constructing, maintaining, and repairing wooden, concrete, and masonry structures, concrete pavement, and waterfront and underwater structures;…

Landscape Builder: software for the creation of initial landscapes for LANDIS from FIA data

Treesearch

William Dijak

2013-01-01

I developed Landscape Builder to create spatially explicit landscapes as starting conditions for LANDIS Pro 7.0 and LANDIS II landscape forest simulation models from classified satellite imagery and Forest Inventory and Analysis (FIA) data collected over multiple years. LANDIS Pro and LANDIS II models project future landscapes by simulating tree growth, tree species...

Report on New Methods for Representing and Interacting with Qualitative Geographic Information, Stage 2: Task Group 3: Social-focused Use Case

DTIC Science & Technology

2014-06-30

lesson learned through exploring current data with the ForceNet tool is that the tool (as implemented thus far) is able to give analysts a big ...including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and...Twitter data and on the development and implementation of tools to support this task; these include a Group Builder, a Force-directed Graph tool, and a

CPO Leadership: Unique and Innovative Leadership Characteristics of Senior Enlisted that Sustain Naval Operations

DTIC Science & Technology

2010-03-01

11 2. History of the Chief Petty Officer Rank and Development of Rank Structure...13 3. Development of Compensation System (Pay Grade)......................21 4. Establishment...Builders Who Train and Develop the Ranks of Today for the Future of the Navy ........48 5. Mastering the Realm of Expertise Will Lead to Credibility

Energy Evaluation of a New Construction Pilot Community: Fresno, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burdick, A.; Poerschke, A.; Rapport, A.

2014-06-01

A new construction pilot community was constructed by builder-partner Wathen-Castanos Hybrid Homes (WCHH) based on a single occupied test house that was designed to achieve greater than 30% energy savings with respect to the House Simulation Protocols (Hendron, Robert; Engebrecht, Cheryn (2010). Building America House Simulation Protocols. Golden, CO: National Renewable Energy Laboratory). Builders face several key problems when implementing a whole-house systems integrated measures package (SIMP) from a single test house into multiple houses. Although a technical solution already may have been evaluated and validated in an individual test house, the potential exists for constructability failures at the communitymore » scale. This report addresses factors of implementation and scalability at the community scale and proposes methodologies by which community-scale energy evaluations can be performed based on results at the occupied test house level. Research focused on the builder and trade implementation of a SIMP and the actual utility usage in the houses at the community scale of production. Five occupants participated in this community-scale research by providing utility bills and information on occupancy and miscellaneous gas and electric appliance use for their houses. IBACOS used these utility data and background information to analyze the actual energy performance of the houses. Verification with measured data is an important component in predictive energy modeling. The actual utility bill readings were compared to projected energy consumption using BEopt with actual weather and thermostat set points for normalization.« less

Information Operations & Security

DTIC Science & Technology

2012-03-05

Fred B. Schneider, Cornell The Promise of Security Metrics • Users: Purchasing decisions – Which system is the better value? • Builders ...Engineering University of Maryland, College Park DISTRIBUTION A: Approved for public release; distribution is unlimited. Digital Multimedia Anti...fingerprints for multimedia content: • Determine the time and place of recordings • Detect tampering in the multimedia content; bind video and

Design and Evaluation of Energy Efficient Modular Classroom Structures.

ERIC Educational Resources Information Center

Brown, G. Z.; And Others

This paper describes a study that developed innovations that would enable modular builders to improve the energy performance of their classrooms without increasing their first cost. The Modern Building Systems' classroom building conforms to the stringent Oregon and Washington energy codes, and, at $18 per square foot, it is at the low end of the…

The GlycanBuilder: a fast, intuitive and flexible software tool for building and displaying glycan structures.

PubMed

Ceroni, Alessio; Dell, Anne; Haslam, Stuart M

2007-08-07

Carbohydrates play a critical role in human diseases and their potential utility as biomarkers for pathological conditions is a major driver for characterization of the glycome. However, the additional complexity of glycans compared to proteins and nucleic acids has slowed the advancement of glycomics in comparison to genomics and proteomics. The branched nature of carbohydrates, the great diversity of their constituents and the numerous alternative symbolic notations, make the input and display of glycans not as straightforward as for example the amino-acid sequence of a protein. Every glycoinformatic tool providing a user interface would benefit from a fast, intuitive, appealing mechanism for input and output of glycan structures in a computer readable format. A software tool for building and displaying glycan structures using a chosen symbolic notation is described here. The "GlycanBuilder" uses an automatic rendering algorithm to draw the saccharide symbols and to place them on the drawing board. The information about the symbolic notation is derived from a configurable graphical model as a set of rules governing the aspect and placement of residues and linkages. The algorithm is able to represent a structure using only few traversals of the tree and is inherently fast. The tool uses an XML format for import and export of encoded structures. The rendering algorithm described here is able to produce high-quality representations of glycan structures in a chosen symbolic notation. The automated rendering process enables the "GlycanBuilder" to be used both as a user-independent component for displaying glycans and as an easy-to-use drawing tool. The "GlycanBuilder" can be integrated in web pages as a Java applet for the visual editing of glycans. The same component is available as a web service to render an encoded structure into a graphical format. Finally, the "GlycanBuilder" can be integrated into other applications to create intuitive and appealing user interfaces: an example is the "GlycoWorkbench", a software tool for assisted annotation of glycan mass spectra. The "GlycanBuilder" represent a flexible, reliable and efficient solution to the problem of input and output of glycan structures in any glycomic tool or database.

Wood preservatives : choosing the right one

Treesearch

Matt Humphries; Stan Lebow; David Moses

2009-01-01

If you are having trouble choosing the right wood preservative system for your application, you are not alone. Dozens of products are available, some older types have gone out of use, others may be completely inappropriate for your application. As designers, specifiers and builders, you need to understand key information to be able to navigate through all of these...

Systems definition study for shuttle demonstration flights of large space structures. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

The development of large space structure technology is discussed, with emphasis on space fabricated structures which are automatically manufactured in space from sheet-strip materials and assembled on-orbit. Definition of a flight demonstration involving an Automated Beam Builder and the building and assembling of large structures is presented.

1986 Year End Report for Road Following at Carnegie-Mellon

DTIC Science & Technology

1987-05-01

how to make them work efficiently. We designed a hierarchical structure and a monitor module which manages all parts of the hierarchy (see figure 1...database, called the Local Map, is managed by a program known as the Local Map Builder (LMB). Each module stores and retrieves information in the...knowledge-intensive modules, and a database manager that synchronizes the modules-is characteristic of a traditional blackboard system. Such a system is

International Behavior Analysis: The Operationalization Task

DTIC Science & Technology

1976-02-15

IJiC. L This report eoBStlttttoa tha first technical report of year t^.-o of the Intcrr.ational Behavior Analysis (IM) Project, vhich is designed ...builders continued to generate "grond designs ," but none of them attempted to specify variable areas in a comprehensive fashion. Ac a result, specific...1970; Meckstroth, 1975). The distinction between "most similar systems" and "most different systems" designs presents the fundamental choice that a

5. DETAIL OF BUILDER'S PLATE, WHICH READS '1898, THE SANITARY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. DETAIL OF BUILDER'S PLATE, WHICH READS '1898, THE SANITARY DISTRICT OF CHICAGO, BOARD OF TRUSTEES, WILLIAM BOLDENWECK, JOSEPH C. BRADEN, ZINA R. CARTER, BERNARD A. ECKART, ALEXANDER J. JONES, THOMAS KELLY, JAMES P. MALLETTE, THOMAS SMYTHE, FRANK WINTER; ISHAM RANDOLPH, CHIEF ENGINEER.' - Santa Fe Railroad, Sanitary & Ship Canal Bridge, Spanning Sanitary & Ship Canal east of Harlem Avenue, Chicago, Cook County, IL

Building America Best Practices Series Volume 15: 40% Whole-House Energy Savings in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-09-01

This best practices guide is the 15th in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the hot-humid climate can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. The best practices describedmore » in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and those requirements are highlighted in the text. Requirements of the 2012 IECC and 2012 IRC are also noted in text and tables throughout the guide. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

Building America Best Practices Series Volume 16: 40% Whole-House Energy Savings in the Mixed-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.

2011-09-01

This best practices guide is the 16th in a series of guides for builders produced by PNNL for the U.S. Department of Energy’s Building America program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the mixed-humid climate can build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers. The best practices describedmore » in this document are based on the results of research and demonstration projects conducted by Building America’s research teams. Building America brings together the nation’s leading building scientists with over 300 production builders to develop, test, and apply innovative, energy-efficient construction practices. Building America builders have found they can build homes that meet these aggressive energy-efficiency goals at no net increased costs to the homeowners. Currently, Building America homes achieve energy savings of 40% greater than the Building America benchmark home (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code). The recommendations in this document meet or exceed the requirements of the 2009 IECC and 2009 IRC and those requirements are highlighted in the text. Requirements of the 2012 IECC and 2012 IRC are also noted in text and tables throughout the guide. This document will be distributed via the DOE Building America website: www.buildingamerica.gov.« less

WebDB Component Builder - Lessons Learned

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macedo, C.

2000-02-15

Oracle WebDB is the easiest way to produce web enabled lightweight and enterprise-centric applications. This concept from Oracle has tantalized our taste for simplistic web development by using a purely web based tool that lives nowhere else but in the database. The use of online wizards, templates, and query builders, which produces PL/SQL behind the curtains, can be used straight ''out of the box'' by both novice and seasoned developers. The topic of this presentation will introduce lessons learned by developing and deploying applications built using the WebDB Component Builder in conjunction with custom PL/SQL code to empower a hybridmore » application. There are two kinds of WebDB components: those that display data to end users via reporting, and those that let end users update data in the database via entry forms. The presentation will also discuss various methods within the Component Builder to enhance the applications pushed to the desktop. The demonstrated example is an application entitled HOME (Helping Other's More Effectively) that was built to manage a yearly United Way Campaign effort. Our task was to build an end to end application which could manage approximately 900 non-profit agencies, an average of 4,100 individual contributions, and $1.2 million dollars. Using WebDB, the shell of the application was put together in a matter of a few weeks. However, we did encounter some hurdles that WebDB, in it's stage of infancy (v2.0), could not solve for us directly. Together with custom PL/SQL, WebDB's Component Builder became a powerful tool that enabled us to produce a very flexible hybrid application.« less

Construction Guidelines for High R-Value Walls without Exterior Rigid Insulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arena, Lois B.

High R-value wall assemblies (R-40 and above) are gaining popularity in the market due to programs such as the U.S. Department of Energy Zero Energy Ready Home program, Passive House, Net Zero Energy Home challenges in several states, and highly incentivized retrofit programs. In response to this demand, several builders have successfully used double-wall systems to achieve higher R-values in thicker, framed walls. To builders of conventional stick-framed homes, often one of the most appealing features of double-wall systems is that there are very few new exterior details. Exterior sheathings, structural bracings, house wraps or building paper, window and doormore » flashings, and siding attachments are usually identical to good details in conventional framed-wall systems. However, although the details in double-wall systems are very similar to those in conventional stick framing, there is sometimes less room for error. Several studies have confirmed colder temperatures of exterior sheathing in high R-value wall assemblies that do not have exterior rigid foam insulation. These colder temperatures can lead to increased chances for condensation from air exfiltration, and they have the potential to result in moisture-related problems (Straube and Smegal 2009, Arena 2014, Ueno 2015). The information presented in this guide is intended to reduce the risk of failure in these types of assemblies, increase durability, and reduce material brought to landfills due to failures and resulting decay. Although this document focuses on double-wall framing techniques, the majority of the information about how to properly construct and finish high R-value assemblies is applicable to all wall assemblies that do not have foam insulation installed on the exterior of the structural sheathing. The techniques presented have been shown through field studies to reduce the likelihood of mold growth and moisture-related damage and are intended for builders, framing contractors, architects, and consultants involved in designing and building super-insulated homes. The information is applicable to both new construction and gut-rehabilitation projects in Climate Zones 5 and higher.« less

The Banana Genome Hub

PubMed Central

Droc, Gaëtan; Larivière, Delphine; Guignon, Valentin; Yahiaoui, Nabila; This, Dominique; Garsmeur, Olivier; Dereeper, Alexis; Hamelin, Chantal; Argout, Xavier; Dufayard, Jean-François; Lengelle, Juliette; Baurens, Franc-Christophe; Cenci, Alberto; Pitollat, Bertrand; D’Hont, Angélique; Ruiz, Manuel; Rouard, Mathieu; Bocs, Stéphanie

2013-01-01

Banana is one of the world’s favorite fruits and one of the most important crops for developing countries. The banana reference genome sequence (Musa acuminata) was recently released. Given the taxonomic position of Musa, the completed genomic sequence has particular comparative value to provide fresh insights about the evolution of the monocotyledons. The study of the banana genome has been enhanced by a number of tools and resources that allows harnessing its sequence. First, we set up essential tools such as a Community Annotation System, phylogenomics resources and metabolic pathways. Then, to support post-genomic efforts, we improved banana existing systems (e.g. web front end, query builder), we integrated available Musa data into generic systems (e.g. markers and genetic maps, synteny blocks), we have made interoperable with the banana hub, other existing systems containing Musa data (e.g. transcriptomics, rice reference genome, workflow manager) and finally, we generated new results from sequence analyses (e.g. SNP and polymorphism analysis). Several uses cases illustrate how the Banana Genome Hub can be used to study gene families. Overall, with this collaborative effort, we discuss the importance of the interoperability toward data integration between existing information systems. Database URL: http://banana-genome.cirad.fr/ PMID:23707967

VQone MATLAB toolbox: A graphical experiment builder for image and video quality evaluations: VQone MATLAB toolbox.

PubMed

Nuutinen, Mikko; Virtanen, Toni; Rummukainen, Olli; Häkkinen, Jukka

2016-03-01

This article presents VQone, a graphical experiment builder, written as a MATLAB toolbox, developed for image and video quality ratings. VQone contains the main elements needed for the subjective image and video quality rating process. This includes building and conducting experiments and data analysis. All functions can be controlled through graphical user interfaces. The experiment builder includes many standardized image and video quality rating methods. Moreover, it enables the creation of new methods or modified versions from standard methods. VQone is distributed free of charge under the terms of the GNU general public license and allows code modifications to be made so that the program's functions can be adjusted according to a user's requirements. VQone is available for download from the project page (http://www.helsinki.fi/psychology/groups/visualcognition/).

Building America Case Study: Performance and Costs of Ductless Heat Pumps in Marine Climate High-Performance Homes: Habitat for Humanity -- The Woods, Tacoma, Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

The Woods is a Habitat for Humanity (HFH) community of ENERGY STAR Homes (c) Northwest (ESHNW)-certified homes located in the marine climate of Tacoma/Pierce County, Washington. This research report builds on an earlier preliminary draft 2014 BA report, and includes significant billing analysis and cost effectiveness research from a collaborative, ongoing Ductless Heat Pump (DHP) research effort for Tacoma Public Utilities (TPU) and Bonneville Power Administration (BPA). This report focuses on the results of field testing, modeling, and monitoring of ductless mini-split heat pump hybrid heating systems in seven homes built and first occupied at various times between September 2013more » and October 2014. The report also provides WSU documentation of high-performance home observations, lessons learned, and stakeholder recommendations for builders of affordable high-performance housing such as HFH.« less

Comfort in High-Performance Homes in a Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poerschke, A.; Beach, R.

2016-01-22

"9IBACOS monitored 37 homes during the late summer and early fall of 2014 in a hot and humid climate to better understand indoor comfort conditions. These homes were constructed in the last several years by four home builders that offered a comfort and performance guarantee for the homes. The homes were located in one of four cities: Tampa, Florida; Orlando, Florida; Houston, Texas; and San Antonio, Texas. Temperature and humidity data were collected from the thermostat and each room of the house using small, battery-powered data loggers. To understand system runtime and its impact on comfort, supply air temperature alsomore » was measured on a 1-minute interval. Overall, the group of homes only exceeded a room-to-room temperature difference of 6 degrees F for 5% of the time. For 80% of the time, the rooms in each house were within 4 degrees F of each other. Additionally, the impact of system runtime on comfort is discussed. Finally, measurements made at the thermostat were used to better understand the occupant operation of each cooling system's thermostat setpoint. Builders were questioned on their perceived impact of offering a comfort and performance guarantee. Their feedback, which generally indicates a positive perception, has been summarized in the report.« less

In search of a representative sample of residential building work.

PubMed

Lobb, Brenda; Woods, Gregory R

2012-09-01

Most research investigating injuries in construction work is limited by reliance on work samples unrepresentative of the multiple, variable-cycle tasks involved, resulting in incomplete characterisation of ergonomic exposures. In this case study, a participatory approach was used including hierarchical task analysis and site observations of a typical team of house builders in New Zealand, over several working days, to obtain a representative work sample. The builders' work consisted of 14 goal-defined jobs using varying subsets of 15 task types, each taking from less than 1 s to more than 1 h and performed in a variety of postures. Task type and duration varied within and between participants and days, although all participants spent at least 25% of the time moving from place to place, mostly carrying materials, and more than half the time either reaching up or bending down to work. This research has provided a description of residential building work based on a work sample more nearly representative than those previously published and has demonstrated a simple, low-cost but robust field observation method that can provide a valid basis for further study of hazard exposures. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Systematic analysis of video data from different human-robot interaction studies: a categorization of social signals during error situations.

PubMed

Giuliani, Manuel; Mirnig, Nicole; Stollnberger, Gerald; Stadler, Susanne; Buchner, Roland; Tscheligi, Manfred

2015-01-01

Human-robot interactions are often affected by error situations that are caused by either the robot or the human. Therefore, robots would profit from the ability to recognize when error situations occur. We investigated the verbal and non-verbal social signals that humans show when error situations occur in human-robot interaction experiments. For that, we analyzed 201 videos of five human-robot interaction user studies with varying tasks from four independent projects. The analysis shows that there are two types of error situations: social norm violations and technical failures. Social norm violations are situations in which the robot does not adhere to the underlying social script of the interaction. Technical failures are caused by technical shortcomings of the robot. The results of the video analysis show that the study participants use many head movements and very few gestures, but they often smile, when in an error situation with the robot. Another result is that the participants sometimes stop moving at the beginning of error situations. We also found that the participants talked more in the case of social norm violations and less during technical failures. Finally, the participants use fewer non-verbal social signals (for example smiling, nodding, and head shaking), when they are interacting with the robot alone and no experimenter or other human is present. The results suggest that participants do not see the robot as a social interaction partner with comparable communication skills. Our findings have implications for builders and evaluators of human-robot interaction systems. The builders need to consider including modules for recognition and classification of head movements to the robot input channels. The evaluators need to make sure that the presence of an experimenter does not skew the results of their user studies.

Systematic analysis of video data from different human–robot interaction studies: a categorization of social signals during error situations

PubMed Central

Giuliani, Manuel; Mirnig, Nicole; Stollnberger, Gerald; Stadler, Susanne; Buchner, Roland; Tscheligi, Manfred

2015-01-01

Human–robot interactions are often affected by error situations that are caused by either the robot or the human. Therefore, robots would profit from the ability to recognize when error situations occur. We investigated the verbal and non-verbal social signals that humans show when error situations occur in human–robot interaction experiments. For that, we analyzed 201 videos of five human–robot interaction user studies with varying tasks from four independent projects. The analysis shows that there are two types of error situations: social norm violations and technical failures. Social norm violations are situations in which the robot does not adhere to the underlying social script of the interaction. Technical failures are caused by technical shortcomings of the robot. The results of the video analysis show that the study participants use many head movements and very few gestures, but they often smile, when in an error situation with the robot. Another result is that the participants sometimes stop moving at the beginning of error situations. We also found that the participants talked more in the case of social norm violations and less during technical failures. Finally, the participants use fewer non-verbal social signals (for example smiling, nodding, and head shaking), when they are interacting with the robot alone and no experimenter or other human is present. The results suggest that participants do not see the robot as a social interaction partner with comparable communication skills. Our findings have implications for builders and evaluators of human–robot interaction systems. The builders need to consider including modules for recognition and classification of head movements to the robot input channels. The evaluators need to make sure that the presence of an experimenter does not skew the results of their user studies. PMID:26217266

XAL Application Framework and Bricks GUI Builder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pelaia II, Tom

2007-01-01

The XAL [1] Application Framework is a framework for rapidly developing document based Java applications with a common look and feel along with many built-in user interface behaviors. The Bricks GUI builder consists of a modern application and framework for rapidly building user interfaces in support of true Model-View-Controller (MVC) compliant Java applications. Bricks and the XAL Application Framework allow developers to rapidly create quality applications.

76 FR 75949 - Requested Administrative Waiver of the Coastwise Trade Laws: Vessel NAGA; Invitation for Public...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

... multi-day charters for up to 6 passengers with particular emphasis on bird watching, natural history and... may have on U.S. vessel builders or businesses in the U.S. that use U.S.-flag vessels. If MARAD... of the waiver will have an unduly adverse effect on a U.S.-vessel builder or a business that uses U.S...

Validation of bioelectrical impedance analysis to hydrostatic weighing in male body builders.

PubMed

Volpe, Stella Lucia; Melanson, Edward L; Kline, Gregory

2010-03-01

The purpose of this study was to compare bioelectrical impedance analysis (BIA) to hydrostatic weighing (HW) in male weight lifters and body builders. Twenty-two male body builders and weight lifters, 23 +/- 3 years of age (mean +/- SD), were studied to determine the efficacy of BIA to HW in this population. Subjects were measured on two separate occasions, 6 weeks apart, for test-retest reliability purposes. Participants recorded 3-day dietary intakes and average work-out times and regimens between the two testing periods. Subjects were, on average, 75 +/- 8 kg of body weight and 175 +/- 7 cm tall. Validation results were as follows: constant error for HW-BIA = 0.128 +/- 3.7%, r for HW versus BIA = -0.294. Standard error of the estimate for BIA = 2.32% and the total error for BIA = 3.6%. Percent body fat was 7.8 +/- 1% from BIA and 8.5 +/- 2% from HW (P > 0.05). Subjects consumed 3,217 +/- 1,027 kcals; 1,848 +/- 768 kcals from carbohydrates; 604 +/- 300 kcals from protein; and 783 +/- 369 kcals from fat. Although work-outs differed among one another, within subject training did not vary. These results suggest that measurement of percent body fat in male body builders and weight trainers is equally as accurate using BIA or HW.

Assessing Security Cooperation: Improving Methods to Maximize Effects

DTIC Science & Technology

2013-03-01

Carl Builder notes, “Institutional and personal interest are not intrinsically bad; but they may be made so if they are always cloaked in altruism and...cooperation professional may be able to lay the groundwork for validating or disqualifying actions based on both countable metrics and anecdotal...Pre-decisional Working Draft), (Washington DC: Multi-Agency, July 31, 2012), 37. 6 Carl H. Builder , The Masks of War: American Military Styles in

Car Builder: Design, Construct and Test Your Own Cars. School Version with Lesson Plans. [CD-ROM].

ERIC Educational Resources Information Center

Highsmith, Joni Bitman

Car Builder is a scientific CD-ROM-based simulation program that lets students design, construct, modify, test, and compare their own cars. Students can design sedans, four-wheel-drive vehicles, vans, sport cars, and hot rods. They may select for aerodynamics, power, and racing ability, or economic and fuel efficiency. It is a program that teaches…

Gambling with the Universe

NASA Astrophysics Data System (ADS)

D'Alto, Nick

2002-07-01

The history and construction of working models of the solar system, called orreries, are described in this article. Fascinated by orreries, the founding fathers of America were men of science who often made references to the orbits of the planets when describing their view of the new world. American, David Rittenhouse, who helped draft the first constitution for the state of Pennsylvania, was a builder of orreries.

Space Fabrication Demonstration System

NASA Technical Reports Server (NTRS)

1977-01-01

Progress in the development of a beam builder to be deployed by space shuttle for assembly of large structures in space is reported. The thermal coating for the structural truss was selected and the detail truss design and analysis completed. Data acquired during verification of the design of the basic 'building block' truss are included as well as design layouts for various fabrication facility subsystems.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare to attach an overhead crane to NASA’s MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare to attach an overhead crane to NASA’s MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers attach an overhead crane to NASA’s MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers attach an overhead crane to NASA’s MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Supplement consumption in body builder athletes

PubMed Central

Karimian, Jahangir; Esfahani, Parivash Shekarchizadeh

2011-01-01

BACKGROUND: Widespread use of supplements is observed among world athletes in different fields. The aim of this study was to estimate the prevalence and determinants of using supplements among body builder athletes. METHODS: This cross-sectional study was conducted on 250 men and 250 women from 30 different bodybuilding clubs. Participants were asked to complete a self-administered standardized anonymous check-list. RESULTS: Forty nine percent of the respondents declared supplement use. Men were more likely to take supplements than women (86.8% vs. 11.2%, p = 0.001). Reasons for using supplements were reported to be for health (45%), enhancing the immune system (40%) and improving athletic performance (25%). Most athletes (72%) had access to a nutritionist but underused this resource. Coaches (65%) had the greatest influence on supplementation practices followed by nutritionists (30%) and doctors (25%) after them. CONCLUSIONS: The prevalence of supplement use among bodybuilders was high. Sex, health-related issues and sport experts were determinant factors of supplement use. PMID:22973330

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, NASA’s MESSENGER spacecraft from NASA’s Goddard Space Flight Center in Greenbelt, Md., is offloaded. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, NASA’s MESSENGER spacecraft from NASA’s Goddard Space Flight Center in Greenbelt, Md., is offloaded. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, a lift helps offload NASA’s MESSENGER spacecraft shipped from NASA’s Goddard Space Flight Center in Greenbelt, Md. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - At the Astrotech Space Operations processing facilities near KSC, a lift helps offload NASA’s MESSENGER spacecraft shipped from NASA’s Goddard Space Flight Center in Greenbelt, Md. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Benchmarking expert system tools

NASA Technical Reports Server (NTRS)

Riley, Gary

1988-01-01

As part of its evaluation of new technologies, the Artificial Intelligence Section of the Mission Planning and Analysis Div. at NASA-Johnson has made timing tests of several expert system building tools. Among the production systems tested were Automated Reasoning Tool, several versions of OPS5, and CLIPS (C Language Integrated Production System), an expert system builder developed by the AI section. Also included in the test were a Zetalisp version of the benchmark along with four versions of the benchmark written in Knowledge Engineering Environment, an object oriented, frame based expert system tool. The benchmarks used for testing are studied.

Closeup view of leeds and northrup strip chart recorders used ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Close-up view of leeds and northrup strip chart recorders used to indicate power usage on certain portions of the system. Note model board builders plaque which reads Kellogg Switchboard and Supply Company- Chicago, USA at left center of photograph. - Thirtieth Street Station, Load Dispatch Center, Thirtieth & Market Streets, Railroad Station, Amtrak (formerly Pennsylvania Railroad Station), Philadelphia, Philadelphia County, PA

40% Whole-House Energy Savings in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

This guide book is a resource to help builders design and construct highly energy-efficient homes, while addressing building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the hot-humid climate can build homes that achieve whole house energy savings of 40% over the Building America benchmark (the 1993 Model Energy Code) with no added overall costs for consumers.

40% Whole-House Energy Savings in the Mixed-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, T. L.; Hefty, M. G.

2011-09-01

This guide book is a resource to help builders design and construct highly energy-efficient homes, while addressing building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the mixed-humid climate can build homes that achieve whole house energy savings of 40% over the Building America benchmark (the 1993 Model Energy Code) with no added overall costs for consumers.

Energy Value Housing Award Guide: How to Build and Profit with Energy Efficiency in New Home Construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sikora, J. L.

2001-06-01

As concern over the environment grows, builders have the potential to fulfill a market niche by building homes that use fewer resources and have lower environmental impact than conventional construction. Builders can increase their marketability and customer satisfaction and, at the same time, reduce the environmental impact of their homes. However, it takes dedication to build environmentally sound homes along with a solid marketing approach to ensure that customers recognize the added value of energy and resource efficiency. This guide is intended for builders seeking suggestions on how to improve energy and resource efficiency in their new homes. It ismore » a compilation of ideas and concepts for designing, building, and marketing energy- and resource-efficient homes based on the experience of recipients of the national Energy Value Housing Award (EVHA).« less

Adaptive Long-Term Monitoring at Environmental Restoration Sites (ER-0629)

DTIC Science & Technology

2009-05-01

Figures Figure 2-1 General Flowchart of Software Application Figure 2-2 Overview of the Genetic Algorithm Approach Figure 2-3 Example of a...and Model Builder) are highlighted on Figure 2-1, which is a general flowchart illustrating the application of the software. The software is applied...monitoring event (e.g., contaminant mass based on interpolation) that modeling is provided by Model Builder. 4 Figure 2-1. General Flowchart of Software

The Air Land Sea Bulletin. Issue No. 2008-2, May 2008

DTIC Science & Technology

2008-05-01

during the meeting. We saw this as a key event because in Iraq the act of breaking bread together is a significant rapport builder and the first...meaning for both parties and were incredible rapport builders —more than that, they created brothers in arms. BUILDING RELATIONSHIPS Once you...possible. Primary disqualifiers for selection as an advisor are medical profiles/issues, lack of security clearances or inability to gain a clearance

OpenSesame: an open-source, graphical experiment builder for the social sciences.

PubMed

Mathôt, Sebastiaan; Schreij, Daniel; Theeuwes, Jan

2012-06-01

In the present article, we introduce OpenSesame, a graphical experiment builder for the social sciences. OpenSesame is free, open-source, and cross-platform. It features a comprehensive and intuitive graphical user interface and supports Python scripting for complex tasks. Additional functionality, such as support for eyetrackers, input devices, and video playback, is available through plug-ins. OpenSesame can be used in combination with existing software for creating experiments.

DOE ZERH Case Study: BPC Green Builders, Taft School, Watertown, CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Case study of a DOE 2015 Housing Innovation Award winning custom home in the cold climate that got a HERS 33 without PV or HERS -14 with PV, with 8.5” double 2x4 walls with 8.5” (R-32) blown cellulose plus R-6 rigid foam, basement with 3” ccsf on interior plus 2x4 stud walls with R-13 blown cellulose, with R-20 around slab, R-38 under slab; a vented attic with R-100 blown cellulose; a central heat pump; HRV; heat pump water heater; 100% LED; and Passive House Institute U.S.+, LEED platinum, and Living Building Challenge certifications.

Preparation of Entangled Polymer Melts of Various Architecture for Coarse-Grained Models

DTIC Science & Technology

2011-09-01

Simulator ( LAMMPS ). This report presents a theory overview and a manual how to use the method. 15. SUBJECT TERMS Ammunition, coarse-grained model...polymer builder, LAMMPS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 26 19a. NAME OF RESPONSIBLE PERSON...scale Atomic/Molecular Massively Parallel Simulator ( LAMMPS ). Gel is an in house written C program of coarse- grained polymer builder, and LAMMPS is

Ocean acidification causes bleaching and productivity loss in coral reef builders.

PubMed

Anthony, K R N; Kline, D I; Diaz-Pulido, G; Dove, S; Hoegh-Guldberg, O

2008-11-11

Ocean acidification represents a key threat to coral reefs by reducing the calcification rate of framework builders. In addition, acidification is likely to affect the relationship between corals and their symbiotic dinoflagellates and the productivity of this association. However, little is known about how acidification impacts on the physiology of reef builders and how acidification interacts with warming. Here, we report on an 8-week study that compared bleaching, productivity, and calcification responses of crustose coralline algae (CCA) and branching (Acropora) and massive (Porites) coral species in response to acidification and warming. Using a 30-tank experimental system, we manipulated CO(2) levels to simulate doubling and three- to fourfold increases [Intergovernmental Panel on Climate Change (IPCC) projection categories IV and VI] relative to present-day levels under cool and warm scenarios. Results indicated that high CO(2) is a bleaching agent for corals and CCA under high irradiance, acting synergistically with warming to lower thermal bleaching thresholds. We propose that CO(2) induces bleaching via its impact on photoprotective mechanisms of the photosystems. Overall, acidification impacted more strongly on bleaching and productivity than on calcification. Interestingly, the intermediate, warm CO(2) scenario led to a 30% increase in productivity in Acropora, whereas high CO(2) lead to zero productivity in both corals. CCA were most sensitive to acidification, with high CO(2) leading to negative productivity and high rates of net dissolution. Our findings suggest that sensitive reef-building species such as CCA may be pushed beyond their thresholds for growth and survival within the next few decades whereas corals will show delayed and mixed responses.

DOE Zero Energy Ready Home Case Study: Manatee County Habitat for Humanity, Ellenton, Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

In this 18-home community, all homes are LEED Platinum and meet ENERGY STAR for Homes Version 3 requirements, HERS 23–53. Half way through the project, Habitat for Humanity heard about the DOE Challenge Home program and signed on, committing to build the next home, a three-bedroom, two-bath, 1,143 ft2 duplex, to Challenge Home criteria. The home is the first DOE Challenge Home in Manatee County, and was awarded a 2013 Housing Innovation Award in the affordable builder category.

DOE Zero Energy Ready Home Case Study: Transformations, Inc., Production House, Devens, Massachusetts

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

A collaboration with Building America team Building Science Corporation helped this builder win a 2013 Housing Innovation Award in 2013—a 2,508-ft2 home built on speculation in the Devens, MA, subdivision. For the above-grade walls, the super-insulated building shell starts with 12 inch thick double walls composed of two 2x4 16-inch on-center walls spaced 5 inches apart. The space between the walls is filled with low-density (open-cell) spray foam for an insulation value of R-45.

KSC-04pd0600

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers secure NASA’s MESSENGER spacecraft on a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0601

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers secure NASA’s MESSENGER spacecraft on a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0602

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers secure NASA’s MESSENGER spacecraft on a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

Advanced Extended Plate and Beam Wall System in a Cold-Climate House

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallay, Dave; Wiehagen, Joseph; Kochkin, Vladimir

This report presents the design and evaluation of an innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders.

Space Construction Automated Fabrication Experiment Definition Study (SCAFEDS). Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1978-01-01

The techniques, processes, and equipment required for automatic fabrication and assembly of structural elements in space using the space shuttle as a launch vehicle and construction base were investigated. Additional construction/systems/operational techniques, processes, and equipment which can be developed/demonstrated in the same program to provide further risk reduction benefits to future large space systems were included. Results in the areas of structure/materials, fabrication systems (beam builder, assembly jig, and avionics/controls), mission integration, and programmatics are summarized. Conclusions and recommendations are given.

A new version of a computer program for dynamical calculations of RHEED intensity oscillations

NASA Astrophysics Data System (ADS)

Daniluk, Andrzej; Skrobas, Kazimierz

2006-01-01

We present a new version of the RHEED program which contains a graphical user interface enabling the use of the program in the graphical environment. The presented program also contains a graphical component which enables displaying program data at run-time through an easy-to-use graphical interface. New version program summaryTitle of program: RHEEDGr Catalogue identifier: ADWV Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADWV Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Catalogue identifier of previous version: ADUY Authors of the original program: A. Daniluk Does the new version supersede the original program: no Computer for which the new version is designed and others on which it has been tested: Pentium-based PC Operating systems or monitors under which the new version has been tested: Windows 9x, XP, NT Programming language used: Borland C++ Builder Memory required to execute with typical data: more than 1 MB Number of bits in a word: 64 bits Number of processors used: 1 Number of lines in distributed program, including test data, etc.: 5797 Number of bytes in distributed program, including test data, etc.: 588 121 Distribution format: tar.gz Nature of physical problem: Reflection high-energy electron diffraction (RHEED) is a very useful technique for studying growth and surface analysis of thin epitaxial structures prepared by the molecular beam epitaxy (MBE). The RHEED technique can reveal, almost instantaneously, changes either in the coverage of the sample surface by adsorbates or in the surface structure of a thin film. Method of solution: RHEED intensities are calculated within the framework of the general matrix formulation of Peng and Whelan [1] under the one-beam condition. Reasons for the new version: Responding to the user feedback we designed a graphical package that enables displaying program data at run-time through an easy-to-use graphical interface. Summary of revisions:In the present form the code is an object-oriented extension of previous version [2]. Fig. 1 shows the static structure of classes and their possible relationships (i.e. inheritance, association, aggregation and dependency) in the code. The code has been modified and optimized to compile under the C++ Builder integrated development environment (IDE). A graphical user interface (GUI) for the program has been created. The application is a standard multiple document interface (MDI) project from Builder's object repository. The MDI application spawns child window that reside within the client window; the main form contains child object. We have added an original graphical component [3] which has been tested successfully in the C++ Builder programming environment under Microsoft Windows platform. Fig. 2 shows internal structure of the component. This diagram is a graphic presentation of the static view which shows a collection of declarative model elements, such as classes, types, and their relationships. Each of the model elements shown in Fig. 2 is manifested by one header file Graph2D.h, and one code file Graph2D.cpp. Fig. 3 sets the stage by showing the package which supplies the C++ Builder elements used in the component. Installation instructions of the TGraph2D.bpk package can be found in the new distribution. The program has been constructed according to the systems development live cycle (SDLC) methodology [4]. Typical running time: The typical running time is machine and user-parameters dependent. Unusual features of the program: The program is distributed in the form of a main project RHEEDGr.bpr with associated files, and should be compiled using Borland C++ Builder compilers version 5 or later.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Puttagunta, S.; Grab, J.; Williamson, J.

Working with builder partners on test homes allows for vetting of whole-house building strategies to eliminate any potential unintended consequences prior to implementing these solution packages on a production scale. To support this research, CARB partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, CT. The philosophy and science behind the 2,700 ft2 "Performance House" was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adapt with the homeowners. The technologies and strategies used in the "Performance House" were not cutting-edge, but simply "best practices practiced". The focus was on simplicitymore » in construction, maintenance, and operation. When seeking a 30% source energy savings targets over a comparable 2009 IECC code-built home in the cold climate zone, nearly all components of a home must be optimized. Careful planning and design are critical. To help builders and architects seeking to match the performance of this home, a step-by-step guide through the building shell components of DOE's Challenge Home are provided in a pictorial story book. The end result was a DOE Challenge Home that achieved a HERS Index Score of 20 (43 without PV, the minimum target was 55 for compliance). This home was also awarded the 2012 HOBI for Best Green Energy Efficient Home from the Home Builders & Remodelers Association of Connecticut.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Puttagunta, S.; Grab, J.; Williamson, J.

Working with builder partners on a test homes allows for vetting of whole-house building strategies to eliminate any potential unintended consequences prior to implementing these solution packages on a production scale. To support this research, CARB partnered with Preferred Builders Inc. on a high-performance test home in Old Greenwich, CT. The philosophy and science behind the 2,700 ft2 'Performance House' was based on the premise that homes should be safe, healthy, comfortable, durable, efficient, and adapt with the homeowners. The technologies and strategies used in the 'Performance House' were not cutting-edge, but simply 'best practices practiced'. The focus was onmore » simplicity in construction, maintenance, and operation. When seeking a 30% source energy savings targets over a comparable 2009 IECC code-built home in the cold climate zone, nearly all components of a home must be optimized. Careful planning and design are critical. To help builders and architects seeking to match the performance of this home, a step-by-step guide through the building shell components of DOE's Challenge Home are provided in a pictorial story book. The end result was a DOE Challenge Home that achieved a HERS Index Score of 20 (43 without PV, the minimum target was 55 for compliance). This home was also awarded the 2012 HOBI for Best Green Energy Efficient Home from the Home Builders & Remodelers Association of Connecticut.« less

Design Principles for E-Government Architectures

NASA Astrophysics Data System (ADS)

Sandoz, Alain

The paper introduces a holistic approach for architecting systems which must sustain the entire e-government activity of a public authority. Four principles directly impact the architecture: Legality, Responsibility, Transparency, and Symmetry leading to coherent representations of the architecture for the client, the designer and the builder. The approach enables to deploy multipartite, distributed public services, including legal delegation of roles and outsourcing of non mandatory tasks through PPP.

Effect of cladding systems on moisture performance of wood-framed walls in a mixed-humid climate

Treesearch

S. Craig Drumheller; Charles G. Carll

2010-01-01

A 22-month field investigation of nine different north-and south-oriented wood-framed wall assemblies was conducted to determine the moisture performance of various wall construction types, most of which incorporated absorptive cladding. The study was conducted on the campus of the National Association of Home Builders (NAHB) Research Center, in Upper Marlboro, MD, 20...

Partial automation of database processing of simulation outputs from L-systems models of plant morphogenesis.

PubMed

Chen, Yi- Ping Phoebe; Hanan, Jim

2002-01-01

Models of plant architecture allow us to explore how genotype environment interactions effect the development of plant phenotypes. Such models generate masses of data organised in complex hierarchies. This paper presents a generic system for creating and automatically populating a relational database from data generated by the widely used L-system approach to modelling plant morphogenesis. Techniques from compiler technology are applied to generate attributes (new fields) in the database, to simplify query development for the recursively-structured branching relationship. Use of biological terminology in an interactive query builder contributes towards making the system biologist-friendly.

Multi-family update to the passive solar construction handbook

NASA Astrophysics Data System (ADS)

Howard, B. D.; Callahan, K. D.

1983-11-01

Builders and developers will accept passive solar construction and designs for integration with their existing practice if accurate and detailed plans of actual, proven passive solar subsystems and assemblies are made available to them. A Passive Solar Construction Handbook was developed. It focuses primarily upon single family homes. The multifamily update of the Handbook, is described and examples of the valuable builder information are shown. It represents a new breakthrough in DOE sponsored projects, performing a Technology Transfer on a most useful level.

Development of a beam builder for automatic fabrication of large composite space structures

NASA Technical Reports Server (NTRS)

Bodle, J. G.

1979-01-01

The composite material beam builder which will produce triangular beams from pre-consolidated graphite/glass/thermoplastic composite material through automated mechanical processes is presented, side member storage, feed and positioning, ultrasonic welding, and beam cutoff are formed. Each process lends itself to modular subsystem development. Initial development is concentrated on the key processes for roll forming and ultrasonic welding composite thermoplastic materials. The construction and test of an experimental roll forming machine and ultrasonic welding process control techniques are described.

KENNEDY SPACE CENTER, FLA. - Doors are open on the air-conditioned transportation van that carried NASA’s MESSENGER spacecraft from NASA’s Goddard Space Flight Center in Greenbelt, Md., to the Astrotech Space Operations processing facilities near KSC. After offloading, MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - Doors are open on the air-conditioned transportation van that carried NASA’s MESSENGER spacecraft from NASA’s Goddard Space Flight Center in Greenbelt, Md., to the Astrotech Space Operations processing facilities near KSC. After offloading, MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Advanced Energy Efficient Roof System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jane Davidson

2008-09-30

Energy consumption in buildings represents 40 percent of primary U.S. energy consumption, split almost equally between residential (22%) and commercial (18%) buildings.1 Space heating (31%) and cooling (12%) account for approximately 9 quadrillion Btu. Improvements in the building envelope can have a significant impact on reducing energy consumption. Thermal losses (or gains) from the roof make up 14 percent of the building component energy load. Infiltration through the building envelope, including the roof, accounts for an additional 28 percent of the heating loads and 16 percent of the cooling loads. These figures provide a strong incentive to develop and implementmore » more energy efficient roof systems. The roof is perhaps the most challenging component of the building envelope to change for many reasons. The engineered roof truss, which has been around since 1956, is relatively low cost and is the industry standard. The roof has multiple functions. A typical wood frame home lasts a long time. Building codes vary across the country. Customer and trade acceptance of new building products and materials may impede market penetration. The energy savings of a new roof system must be balanced with other requirements such as first and life-cycle costs, durability, appearance, and ease of construction. Conventional residential roof construction utilizes closely spaced roof trusses supporting a layer of sheathing and roofing materials. Gypsum board is typically attached to the lower chord of the trusses forming the finished ceiling for the occupied space. Often in warmer climates, the HVAC system and ducts are placed in the unconditioned and otherwise unusable attic. High temperature differentials and leaky ducts result in thermal losses. Penetrations through the ceilings are notoriously difficult to seal and lead to moisture and air infiltration. These issues all contribute to greater energy use and have led builders to consider construction of a conditioned attic. The options considered to date are not ideal. One approach is to insulate between the trusses at the roof plane. The construction process is time consuming and costs more than conventional attic construction. Moreover, the problems of air infiltration and thermal bridges across the insulation remain. Another approach is to use structurally insulated panels (SIPs), but conventional SIPs are unlikely to be the ultimate solution because an additional underlying support structure is required except for short spans. In addition, wood spline and metal locking joints can result in thermal bridges and gaps in the foam. This study undertook a more innovative approach to roof construction. The goal was to design and evaluate a modular energy efficient panelized roof system with the following attributes: (1) a conditioned and clear attic space for HVAC equipment and additional finished area in the attic; (2) manufactured panels that provide structure, insulation, and accommodate a variety of roofing materials; (3) panels that require support only at the ends; (4) optimal energy performance by minimizing thermal bridging and air infiltration; (5) minimal risk of moisture problems; (6) minimum 50-year life; (7) applicable to a range of house styles, climates and conditions; (8) easy erection in the field; (9) the option to incorporate factory-installed solar systems into the panel; and (10) lowest possible cost. A nationwide market study shows there is a defined market opportunity for such a panelized roof system with production and semi-custom builders in the United States. Senior personnel at top builders expressed interest in the performance attributes and indicate long-term opportunity exists if the system can deliver a clear value proposition. Specifically, builders are interested in (1) reducing construction cycle time (cost) and (2) offering increased energy efficiency to the homebuyer. Additional living space under the roof panels is another low-cost asset identified as part of the study. The market potential is enhanced through construction activity levels in target markets. Southern markets, from Florida to Texas account for 50 percent of the total new construction angled-roof volume. California contributes an additional 13 percent share of market volume. These states account for 28 to 30 million squares (2.8 to 3 billion square feet) of new construction angled roof opportunity. The major risk to implementation is the uncertainty of incorporating new design and construction elements into the construction process. By coordinating efforts to enhance the drivers for adoption and minimize the barriers, the panelized roof system stands to capitalize on a growing market demand for energy efficient building alternatives and create a compelling case for market adoption.« less

Time-related patient data retrieval for the case studies from the pharmacogenomics research network

PubMed Central

Zhu, Qian; Tao, Cui; Ding, Ying; Chute, Christopher G.

2012-01-01

There are lots of question-based data elements from the pharmacogenomics research network (PGRN) studies. Many data elements contain temporal information. To semantically represent these elements so that they can be machine processiable is a challenging problem for the following reasons: (1) the designers of these studies usually do not have the knowledge of any computer modeling and query languages, so that the original data elements usually are represented in spreadsheets in human languages; and (2) the time aspects in these data elements can be too complex to be represented faithfully in a machine-understandable way. In this paper, we introduce our efforts on representing these data elements using semantic web technologies. We have developed an ontology, CNTRO, for representing clinical events and their temporal relations in the web ontology language (OWL). Here we use CNTRO to represent the time aspects in the data elements. We have evaluated 720 time-related data elements from PGRN studies. We adapted and extended the knowledge representation requirements for EliXR-TIME to categorize our data elements. A CNTRO-based SPARQL query builder has been developed to customize users’ own SPARQL queries for each knowledge representation requirement. The SPARQL query builder has been evaluated with a simulated EHR triple store to ensure its functionalities. PMID:23076712

Time-related patient data retrieval for the case studies from the pharmacogenomics research network.

PubMed

Zhu, Qian; Tao, Cui; Ding, Ying; Chute, Christopher G

2012-11-01

There are lots of question-based data elements from the pharmacogenomics research network (PGRN) studies. Many data elements contain temporal information. To semantically represent these elements so that they can be machine processiable is a challenging problem for the following reasons: (1) the designers of these studies usually do not have the knowledge of any computer modeling and query languages, so that the original data elements usually are represented in spreadsheets in human languages; and (2) the time aspects in these data elements can be too complex to be represented faithfully in a machine-understandable way. In this paper, we introduce our efforts on representing these data elements using semantic web technologies. We have developed an ontology, CNTRO, for representing clinical events and their temporal relations in the web ontology language (OWL). Here we use CNTRO to represent the time aspects in the data elements. We have evaluated 720 time-related data elements from PGRN studies. We adapted and extended the knowledge representation requirements for EliXR-TIME to categorize our data elements. A CNTRO-based SPARQL query builder has been developed to customize users' own SPARQL queries for each knowledge representation requirement. The SPARQL query builder has been evaluated with a simulated EHR triple store to ensure its functionalities.

U.S. Department of Energy Zero Energy Ready Home Implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rothgeb, Stacey K; Schirber, T.; Mosiman, G.

The intention of this project is to assist home builders in the upper Midwest in achieving DOE Zero Energy Ready Home program certification, and to document the process and outcomes involved in meeting this rigorous standard. NorthernSTAR, in conjunction with our program partner Building Knowledge, Inc., provided technical support to the builders during the design and construction process. At the time of this publication, four qualifying homes have been completed and an additional three are currently under construction to be completed later this year. Three additional homes were excluded from certification due to the HVAC contractor not completing their requiredmore » credentialing until after completion of the homes, though the energy performance would have otherwise qualified the homes for program certification. Both Amaris Homes and Cobblestone Homes note that participation in the ZERH program provides them with competitive advantage in the market place at reasonable construction costs that also result in extremely satisfied clients who are willing to recommend the builders to friends and family.« less

Free amino acids in spider hemolymph.

PubMed

Tillinghast, Edward K; Townley, Mark A

2008-11-01

We examined the free amino acid composition of hemolymph from representatives of five spider families with an interest in knowing if the amino acid profile in the hemolymph of orb-web-building spiders reflects the high demands for small organic compounds in the sticky droplets of their webs. In nearly all analyses, on both orb and non-orb builders, glutamine was the most abundant free amino acid. Glycine, taurine, proline, histidine, and alanine also tended to be well-represented in orb and non-orb builders. While indications of taxon-specific differences in amino acid composition were observed, it was not apparent that two presumptive precursors (glutamine, taurine) of orb web sticky droplet compounds were uniquely enriched in araneids (orb builders). However, total amino acid concentrations were invariably highest in the araneids and especially so in overwintering juveniles, even as several of the essential amino acids declined during this winter diapause. Comparing the data from this study with those from earlier studies revealed a number of discrepancies. The possible origins of these differences are discussed.

Approaches to 30 Percent Energy Savings at the Community Scale in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas-Rees, S.; Beal, D.; Martin, E.

2013-03-01

BA-PIRC has worked with several community-scale builders within the hot humid climate zone to improve performance of production, or community scale, housing. Tommy Williams Homes (Gainesville, FL), Lifestyle Homes (Melbourne, FL), and Habitat for Humanity (various locations, FL) have all been continuous partners of the Building America program and are the subjects of this report to document achievement of the Building America goal of 30% whole house energy savings packages adopted at the community scale. Key aspects of this research include determining how to evolve existing energy efficiency packages to produce replicable target savings, identifying what builders' technical assistance needsmore » are for implementation and working with them to create sustainable quality assurance mechanisms, and documenting the commercial viability through neutral cost analysis and market acceptance. This report documents certain barriers builders overcame and the approaches they implemented in order to accomplish Building America (BA) Program goals that have not already been documented in previous reports.« less

Space Fabrication Demonstration System

NASA Technical Reports Server (NTRS)

1978-01-01

Progress in the mechanical/structural assembly of the beam builder is reported. The following structures were investigated: cross brace magazine/dispenser subsystem; and rolling mill supply reel, guide, and drive. The fabrication facility design and a detail design of all major subsystem components are discussed. The number of spot welds per structural joint were reduced which enables the doubling of length of truss which can be produced within known electrode life limits.

Social learning in nest-building birds: a role for familiarity.

PubMed

Guillette, Lauren M; Scott, Alice C Y; Healy, Susan D

2016-03-30

It is becoming apparent that birds learn from their own experiences of nest building. What is not clear is whether birds can learn from watching conspecifics build. As social learning allows an animal to gain information without engaging in costly trial-and-error learning, first-time builders should exploit the successful habits of experienced builders. We presented first-time nest-building male zebra finches with either a familiar or an unfamiliar conspecific male building with material of a colour the observer did not like. When given the opportunity to build, males that had watched a familiar male build switched their material preference to that used by the familiar male. Males that observed unfamiliar birds did not. Thus, first-time nest builders use social information and copy the nest material choices when demonstrators are familiar but not when they are strangers. The relationships between individuals therefore influence how nest-building expertise is socially transmitted in zebra finches. © 2016 The Author(s).

Social learning in nest-building birds: a role for familiarity

PubMed Central

Guillette, Lauren M.; Scott, Alice C. Y.; Healy, Susan D.

2016-01-01

It is becoming apparent that birds learn from their own experiences of nest building. What is not clear is whether birds can learn from watching conspecifics build. As social learning allows an animal to gain information without engaging in costly trial-and-error learning, first-time builders should exploit the successful habits of experienced builders. We presented first-time nest-building male zebra finches with either a familiar or an unfamiliar conspecific male building with material of a colour the observer did not like. When given the opportunity to build, males that had watched a familiar male build switched their material preference to that used by the familiar male. Males that observed unfamiliar birds did not. Thus, first-time nest builders use social information and copy the nest material choices when demonstrators are familiar but not when they are strangers. The relationships between individuals therefore influence how nest-building expertise is socially transmitted in zebra finches. PMID:27009230

Performance and Costs of Ductless Heat Pumps in Marine-Climate High-Performance Homes -- Habitat for Humanity The Woods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lubliner, Michael; Howard, Luke; Hales, David

The Woods is a Habitat for Humanity (HFH) community of ENERGY STAR Homes Northwest (ESHNW)-certified homes located in the marine climate of Tacoma/Pierce County, Washington. This research report builds on an earlier preliminary draft 2014 BA report, and includes significant billing analysis and cost effectiveness research from a collaborative, ongoing Ductless Heat Pump (DHP)research effort for Tacoma Public Utilities (TPU) and Bonneville Power Administration (BPA). This report focuses on the results of field testing, modeling, and monitoring of ductless mini-split heat pump hybrid heating systems in seven homes built and first occupied at various times between September 2013 and Octobermore » 2014. The report also provides WSU documentation of high-performance home observations, lessons learned, and stakeholder recommendations for builders of affordable high-performance housing such as HFH. Tacoma Public Utilities (TPU) and Bonneville Power Administration (BPA). This report focuses on the results of field testing, modeling, and monitoring of ductless mini-split heat pump hybrid heating systems in seven homes built and first occupied at various times between September 2013 and October 2014. The report also provides WSU documentation of high-performance home observations, lessons learned, and stakeholder recommendations for builders of affordable high-performance housing such as HFH.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aldrich, Robb; Butterfield, Karla

With funding from the Building America Program, part of the U.S. Department of Energy Building Technologies Office, the Consortium for Advanced Residential Buildings (CARB) worked with BrightBuilt Home (BBH) to evaluate and optimize building systems. CARB’s work focused on a home built by Black Bros. Builders in Lincolnville, Maine (International Energy Conservation Code Climate Zone 6). As with most BBH projects to date, modular boxes were built by Keiser Homes in Oxford, Maine.

Achievers, Confidence-Builders, Advocates, Relationship-Developers and System-Changers: What "Making a Difference" Means to Those Who Work with Children with Special Educational Needs -- A Typology of Rewards

ERIC Educational Resources Information Center

Mackenzie, Suzanne

2013-01-01

Previous research on the rewards found that teachers gain satisfaction in a sense of vocation, "making a difference", and the emotional rewards of "care" and "love", especially in whole-class teaching. The meaning of "making a difference" often remains unexplored however, and this article is an attempt to…

BioPartsBuilder: a synthetic biology tool for combinatorial assembly of biological parts.

PubMed

Yang, Kun; Stracquadanio, Giovanni; Luo, Jingchuan; Boeke, Jef D; Bader, Joel S

2016-03-15

Combinatorial assembly of DNA elements is an efficient method for building large-scale synthetic pathways from standardized, reusable components. These methods are particularly useful because they enable assembly of multiple DNA fragments in one reaction, at the cost of requiring that each fragment satisfies design constraints. We developed BioPartsBuilder as a biologist-friendly web tool to design biological parts that are compatible with DNA combinatorial assembly methods, such as Golden Gate and related methods. It retrieves biological sequences, enforces compliance with assembly design standards and provides a fabrication plan for each fragment. BioPartsBuilder is accessible at http://public.biopartsbuilder.org and an Amazon Web Services image is available from the AWS Market Place (AMI ID: ami-508acf38). Source code is released under the MIT license, and available for download at https://github.com/baderzone/biopartsbuilder joel.bader@jhu.edu Supplementary data are available at Bioinformatics online. © The Author 2015. Published by Oxford University Press.

The art of thermal mass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, B.

1999-10-01

From cave dwellers to pueblo builders, early people of the southwest used the earth to moderated the extremes of their climate. Now, at the turn of the 21st century, a Colorado builder combines ancient knowledge with high technology to create modern homes that stay naturally warm in the winter and cool in the summer. With passive solar design, incorporating lots concrete mass, Judy Niemeyer builds custom homes that hardly even need thermostats. Before clients Ralph and Sharon Dickman stumbled into Niemeyer, owner of Tierra Concrete Homes in Pueblo, Colorado, thermal mass was not in their vocabulary. Now, when temperatures reachmore » 100 F (38 C) in July and their neighbors are running up their electric bills, the Dickmans are saving for vacation. With the thermal mass integrated into their new home, they don't need a cooling system. And in winter, their gas-fired log fireplace is about all they need to supplement the sun. ``We love the natural lighting, the open feeling and the great view out the huge windows,'' says Sharon. And they stay comfortable year-round with very low energy bills.« less

Ocean acidification causes bleaching and productivity loss in coral reef builders

PubMed Central

Anthony, K. R. N.; Kline, D. I.; Diaz-Pulido, G.; Dove, S.; Hoegh-Guldberg, O.

2008-01-01

Ocean acidification represents a key threat to coral reefs by reducing the calcification rate of framework builders. In addition, acidification is likely to affect the relationship between corals and their symbiotic dinoflagellates and the productivity of this association. However, little is known about how acidification impacts on the physiology of reef builders and how acidification interacts with warming. Here, we report on an 8-week study that compared bleaching, productivity, and calcification responses of crustose coralline algae (CCA) and branching (Acropora) and massive (Porites) coral species in response to acidification and warming. Using a 30-tank experimental system, we manipulated CO2 levels to simulate doubling and three- to fourfold increases [Intergovernmental Panel on Climate Change (IPCC) projection categories IV and VI] relative to present-day levels under cool and warm scenarios. Results indicated that high CO2 is a bleaching agent for corals and CCA under high irradiance, acting synergistically with warming to lower thermal bleaching thresholds. We propose that CO2 induces bleaching via its impact on photoprotective mechanisms of the photosystems. Overall, acidification impacted more strongly on bleaching and productivity than on calcification. Interestingly, the intermediate, warm CO2 scenario led to a 30% increase in productivity in Acropora, whereas high CO2 lead to zero productivity in both corals. CCA were most sensitive to acidification, with high CO2 leading to negative productivity and high rates of net dissolution. Our findings suggest that sensitive reef-building species such as CCA may be pushed beyond their thresholds for growth and survival within the next few decades whereas corals will show delayed and mixed responses. PMID:18988740

Measure Guideline. Transitioning From Three-Coat Stucco to One-Coat Stucco With EPS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Davis, G.; Rapport, A.

2012-04-01

This measure guideline has been developed to help builders transition from using a traditional three-coat stucco wall-cladding system to a one-coat stucco wall-cladding system with expanded polystyrene (EPS) insulated sheathing. The one-coat system maintains the look of a traditional stucco system but uses only a base layer and a finish coat over EPS insulation that achieves higher levels of energy efficiency. Potential risks associated with the installation of a one-coat stucco system are addressed in terms of design, installation, and warranty concerns such as cracking and delamination, along with mitigation strategies to reduce these risks.

KSC-04pd0603

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, the attachment of NASA’s MESSENGER spacecraft to a test stand is complete. The spacecraft is now ready for employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, to begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0599

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers verify the correct placement of NASA’s MESSENGER spacecraft on a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0598

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers check for the correct alignment of NASA’s MESSENGER spacecraft as it is lowered onto a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0597

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers prepare for contact of NASA’s MESSENGER spacecraft with a test stand. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0594

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers prepare to move NASA’s MESSENGER spacecraft onto a test stand using an overhead crane. There, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0595

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers lower NASA’s MESSENGER spacecraft onto a test stand using an overhead crane. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

KSC-04pd0596

NASA Image and Video Library

2004-03-22

KENNEDY SPACE CENTER, FLA. -- At the Astrotech Space Operations processing facilities, workers monitor NASA’s MESSENGER spacecraft as it is lowered onto a test stand by an overhead crane. Once in place, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will begin final processing for launch, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be launched aboard a Boeing Delta II rocket no earlier than July 30 on a six-year mission to study the planet Mercury.

Technology Solutions Case Study: Initial and Long-Term MOvement of Cladding Installed Over Exterior Rigid Insulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Changes in the International Energy Conservation Code (IECC) from 2009 to 2012 have resulted in the use of exterior rigid insulation becoming part of the prescriptive code requirements. With more jurisdictions adopting the 2012 IECC, builders will be required to incorporate exterior insulation in the construction of their exterior wall assemblies. For thick layers of exterior insulation (levels greater than 1.5 inches), the use of wood of furring strips attached through the insulation back to the structure has been used by many contractors and designers as a means to provide a convenient cladding attachment location. However, there has been resistancemore » to its widespread implementation due to a lack of research and understanding of the mechanisms involved and potential creep effects of the assembly under the sustained dead load of a cladding. This research conducted by Building Science Corporation evaluated the system mechanics and long-term performance of this technique.« less

Space fabrication: Graphite composite truss welding and cap forming subsystems

NASA Technical Reports Server (NTRS)

Jenkins, L. M.; Browning, D. L.

1980-01-01

An automated beam builder for the fabrication of space structures is described. The beam builder forms a triangular truss 1.3 meters on a side. Flat strips of preconsolidated graphite fiber fabric in a polysulfone matrix are coiled in a storage canister. Heaters raise the material to forming temperature then the structural cap section is formed by a series of rollers. After cooling, cross members and diagonal tension cords are ultrasonically welded in place to complete the truss. The stability of fabricated structures and composite materials is also examined.

Digital Topographic Support System (DTSS).

DTIC Science & Technology

1987-07-29

effects applications software, a word processing package and a Special Purpose Product Builder ( SPPB ) in terms common to his Job. Through the MI, the...communicating with the TA in terms he understands, the applications software, the SPPB and the GIS form the underlying tools which perform the computations and...displayed on the monitors or plotted on paper or Mylar. The SPPB will guide the TA enabling him to design products which are not included in the applications

Residential Photovoltaic Energy Systems in California: The Effect on Home Sales Prices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoen, Ben; Wiser, Ryan; Thayer, Mark

2012-04-15

Relatively little research exists estimating the marginal impacts of photovoltaic (PV) energy systems on home sale prices. Using a large dataset of California homes that sold from 2000 through mid-2009, we find strong evidence, despite a variety of robustness checks, that existing homes with PV systems sold for a premium over comparable homes without PV systems, implying a near full return on investment. Premiums for new homes are found to be considerably lower than those for existing homes, implying, potentially, a tradeoff between price and sales velocity. The results have significant implications for homeowners, builders, appraisers, lenders, and policymakers.

Data acquisition system for the Belle experiment

NASA Astrophysics Data System (ADS)

Nakao, M.; Yamauchi, M.; Suzuki, S. Y.; Itoh, R.; Fujii, H.

2000-04-01

We built a data acquisition system for the Belle experiment at the KEK B-factory. The system is designed to record the signals from the detectors at 500 Hz trigger rate with a less than 10% dead time fraction. A typical event size is 30 kbyte, which corresponds to a data transfer rate of 15 Mbyte/s. Main components are two kinds of detector readout systems, an event builder, an online computer farm and a data storage system. The system has been reliably in operation at the design performance for a half year. We have completed cosmic-ray data taking for 2.5 months and have started physics data taking on Jun. 1, 1999.

Sub-Saharan Africa Report.

DTIC Science & Technology

1987-04-14

Peter Stacey; BUSINESS DAY, 18 Mar 87) 110 PRC Makes Trade Gesture (Frank Jeans; THE STAR, 18 Mar 87) Ill Briefs Number of Unemployed Indians...Up 112 Rise in Exports From Richards Bay 112 PGA Borehole Strikes Bird Reef 112 Builders Fund Gets Boost 112 Lisbon Trade Mission Arrives 113...opportunity to create their own social conditions for themselves. It is for the same reason that we criticise the system of international trade . It is not

Performance and Costs of Ductless Heat Pumps in Marine-Climate High-Performance Homes -- Habitat for Humanity The Woods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael Lubliner; Howard, Luke; Hales, David

2016-02-23

This final Building America Partnership report focuses on the results of field testing, modeling, and monitoring of ductless mini-split heat pump hybrid heating systems in seven homes built and first occupied at various times between September 2013 and October 2014. The report also provides WSU documentation of high-performance home observations, lessons learned, and stakeholder recommendations for builders of affordable high-performance housing.

KENNEDY SPACE CENTER, FLA. - Shipped in an air-conditioned transportation van from NASA’s Goddard Space Flight Center in Greenbelt, Md., NASA’s MESSENGER spacecraft, the first Mercury orbiter, arrives at the Astrotech Space Operations processing facilities near KSC. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be offloaded and taken into a high bay clean room. After the spacecraft is removed from its shipping container, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

NASA Image and Video Library

2004-03-10

KENNEDY SPACE CENTER, FLA. - Shipped in an air-conditioned transportation van from NASA’s Goddard Space Flight Center in Greenbelt, Md., NASA’s MESSENGER spacecraft, the first Mercury orbiter, arrives at the Astrotech Space Operations processing facilities near KSC. MESSENGER - short for MErcury Surface, Space ENvironment, GEochemistry and Ranging - will be offloaded and taken into a high bay clean room. After the spacecraft is removed from its shipping container, employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

New Whole-House Solutions Case Study: Zero Energy Ready Home Multifamily Project: Mutual Housing at Spring Lake

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. Springer and A. German

2015-09-01

Building cost effective, high performance homes that provide superior comfort, health, and durability is the goal of the Department of Energy's (DOE's) Zero Energy Ready Homes (ZERH) program. This case study describes the development of a 62-unit multifamily community constructed by nonprofit developer Mutual Housing at the Spring Lake subdivision in Woodland, California. The Spring Lake project is expected to be the first ZERH-certified multifamily project nationwide. Building America team Alliance for Residential Building Innovation worked with Mutual Housing throughout the project. An objective of this project was to gain a highly visible foothold for residential buildings built to themore » DOE ZERH specification that can be used to encourage participation by other California builders.« less

Business Metrics for High-Performance Homes: A Colorado Springs Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beach, R.; Jones, A.

The building industry needs to understand how energy ratings can impact homebuilders. Of interest is how energy efficiency may or may not have a positive impact on homebuilders’ business success. Focusing on Colorado Springs, Colorado, as a case study, the U.S. Department of Energy’s Building America research team IBACOS suggests a win–win between a builder’s investment in energy efficiency and that builder’s ability to sell homes. Although this research did not ultimately determine why a correlation may exist, a builder’s investment in voluntary energy-efficiency programs correlated with that builder’s ability to survive the Great Recession of 2007 to 2009. Thismore » report explores the relationship between energy-efficiency ratings and the market performance of several builders in Colorado Springs.« less

System diagnostic builder

NASA Technical Reports Server (NTRS)

Nieten, Joseph L.; Burke, Roger

1992-01-01

The System Diagnostic Builder (SDB) is an automated software verification and validation tool using state-of-the-art Artificial Intelligence (AI) technologies. The SDB is used extensively by project BURKE at NASA-JSC as one component of a software re-engineering toolkit. The SDB is applicable to any government or commercial organization which performs verification and validation tasks. The SDB has an X-window interface, which allows the user to 'train' a set of rules for use in a rule-based evaluator. The interface has a window that allows the user to plot up to five data parameters (attributes) at a time. Using these plots and a mouse, the user can identify and classify a particular behavior of the subject software. Once the user has identified the general behavior patterns of the software, he can train a set of rules to represent his knowledge of that behavior. The training process builds rules and fuzzy sets to use in the evaluator. The fuzzy sets classify those data points not clearly identified as a particular classification. Once an initial set of rules is trained, each additional data set given to the SDB will be used by a machine learning mechanism to refine the rules and fuzzy sets. This is a passive process and, therefore, it does not require any additional operator time. The evaluation component of the SDB can be used to validate a single software system using some number of different data sets, such as a simulator. Moreover, it can be used to validate software systems which have been re-engineered from one language and design methodology to a totally new implementation.

Intervertebral discitis caused by nontypeable Haemophilus influenzae in an adult: Case report.

PubMed

Boulton, R; Swayamprakasam, A; Raza, M

2012-01-01

Haemophilus influenzae is a common cause of bacterial meningitis in children and can cause upper respiratory tract infections in adults, but has yet to be reported solely involving intervertebral discitis. A 67-year-old builder presenting with fever, myalgia and back pain is found to have intervertebral discitis (confirmed on MRI) caused by H. influenzae (identified on blood cultures). A nontypeable form of H. influenzae has not been reported causing discitis. We describe a case in a relatively fit individual who was treated successfully with antimicrobial treatment. A preceding upper respiratory tract infection is the presumed source of infection, predisposed by long-term low-dose steroid therapy. H. influenzae is a rare, but treatable cause of discitis. Copyright © 2012 Surgical Associates Ltd. Published by Elsevier Ltd. All rights reserved.

Re-evaluating the health of coral reef communities: baselines and evidence for human impacts across the central Pacific.

PubMed

Smith, Jennifer E; Brainard, Rusty; Carter, Amanda; Grillo, Saray; Edwards, Clinton; Harris, Jill; Lewis, Levi; Obura, David; Rohwer, Forest; Sala, Enric; Vroom, Peter S; Sandin, Stuart

2016-01-13

Numerous studies have documented declines in the abundance of reef-building corals over the last several decades and in some but not all cases, phase shifts to dominance by macroalgae have occurred. These assessments, however, often ignore the remainder of the benthos and thus provide limited information on the present-day structure and function of coral reef communities. Here, using an unprecedentedly large dataset collected within the last 10 years across 56 islands spanning five archipelagos in the central Pacific, we examine how benthic reef communities differ in the presence and absence of human populations. Using islands as replicates, we examine whether benthic community structure is associated with human habitation within and among archipelagos and across latitude. While there was no evidence for coral to macroalgal phase shifts across our dataset we did find that the majority of reefs on inhabited islands were dominated by fleshy non-reef-building organisms (turf algae, fleshy macroalgae and non-calcifying invertebrates). By contrast, benthic communities from uninhabited islands were more variable but in general supported more calcifiers and active reef builders (stony corals and crustose coralline algae). Our results suggest that cumulative human impacts across the central Pacific may be causing a reduction in the abundance of reef builders resulting in island scale phase shifts to dominance by fleshy organisms. © 2016 The Author(s).

A distributed analysis and visualization system for model and observational data

NASA Technical Reports Server (NTRS)

Wilhelmson, Robert B.

1994-01-01

Software was developed with NASA support to aid in the analysis and display of the massive amounts of data generated from satellites, observational field programs, and from model simulations. This software was developed in the context of the PATHFINDER (Probing ATmospHeric Flows in an Interactive and Distributed EnviRonment) Project. The overall aim of this project is to create a flexible, modular, and distributed environment for data handling, modeling simulations, data analysis, and visualization of atmospheric and fluid flows. Software completed with NASA support includes GEMPAK analysis, data handling, and display modules for which collaborators at NASA had primary responsibility, and prototype software modules for three-dimensional interactive and distributed control and display as well as data handling, for which NSCA was responsible. Overall process control was handled through a scientific and visualization application builder from Silicon Graphics known as the Iris Explorer. In addition, the GEMPAK related work (GEMVIS) was also ported to the Advanced Visualization System (AVS) application builder. Many modules were developed to enhance those already available in Iris Explorer including HDF file support, improved visualization and display, simple lattice math, and the handling of metadata through development of a new grid datatype. Complete source and runtime binaries along with on-line documentation is available via the World Wide Web at: http://redrock.ncsa.uiuc.edu/ PATHFINDER/pathre12/top/top.html.

KSC-04PD-0431

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers remove the protective cover from NASAs MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0432

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers remove the protective cover from NASAs MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0442

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. At the Astrotech Space Operations processing facilities, workers check the placement of NASAs MESSENGER spacecraft on a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0443

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. At the Astrotech Space Operations processing facilities, workers check the placement of NASAs MESSENGER spacecraft on a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0429

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. At the Astrotech Space Operations processing facilities near KSC, workers move NASAs MESSENGER spacecraft into a high bay clean room. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

CICADA, CCD and Instrument Control Software

NASA Astrophysics Data System (ADS)

Young, Peter J.; Brooks, Mick; Meatheringham, Stephen J.; Roberts, William H.

Computerised Instrument Control and Data Acquisition (CICADA) is a software system for control of telescope instruments in a distributed computing environment. It is designed using object-oriented techniques and built with standard computing tools such as RPC, SysV IPC, Posix threads, Tcl, and GUI builders. The system is readily extensible to new instruments and currently supports the Astromed 3200 CCD controller and MSSSO's new tip-tilt system. Work is currently underway to provide support for the SDSU CCD controller and MSSSO's Double Beam Spectrograph. A core set of processes handle common communication and control tasks, while specific instruments are ``bolted'' on using C++ inheritance techniques.

How Architecture-Driven Modernization Is Changing the Game in Information System Modernization

DTIC Science & Technology

2010-04-01

Health Administration MUMPS  to Java 300K 4 mo. State of OR Employee Retirement System COBOL to C# .Net 250K 4 mo. Civilian State of WA Off. of Super of...Jovial, Mumps , A MagnaX, Natural, B PVL, P owerBuilder, A SQL, Vax Basic, s V B 6, + Others E revolution, inc. C, Target System "To Be" C#, C...successfully completed in 4 months • Created a new JANUSTM MUMPS parser TM , Implementation • Final “To-Be” Documentation • JANUS rules engine

Consular Reports on Industrial Education in Germany: I. The System of Industrial Schooling; II. Schools for Builders; III. Preparatory Courses for Master Craftsmen; IV. "Meisterkurse" at Frankfort on the Main; V. The Trade Institute at Cologne; VI. Schools for Fruit-Growing. Bulletin, 1913, No. 54. Whole Number 565

ERIC Educational Resources Information Center

United States Bureau of Education, Department of the Interior, 1913

1913-01-01

The people of the United States are greatly interested in the German systems of industrial and trade education. There is a large demand for information in regard to the general policies of German cities and States in regard to such education, and also for information in regard to schools for special trades. To meet this demand, this bulletin…

Highly scalable and robust rule learner: performance evaluation and comparison.

PubMed

Kurgan, Lukasz A; Cios, Krzysztof J; Dick, Scott

2006-02-01

Business intelligence and bioinformatics applications increasingly require the mining of datasets consisting of millions of data points, or crafting real-time enterprise-level decision support systems for large corporations and drug companies. In all cases, there needs to be an underlying data mining system, and this mining system must be highly scalable. To this end, we describe a new rule learner called DataSqueezer. The learner belongs to the family of inductive supervised rule extraction algorithms. DataSqueezer is a simple, greedy, rule builder that generates a set of production rules from labeled input data. In spite of its relative simplicity, DataSqueezer is a very effective learner. The rules generated by the algorithm are compact, comprehensible, and have accuracy comparable to rules generated by other state-of-the-art rule extraction algorithms. The main advantages of DataSqueezer are very high efficiency, and missing data resistance. DataSqueezer exhibits log-linear asymptotic complexity with the number of training examples, and it is faster than other state-of-the-art rule learners. The learner is also robust to large quantities of missing data, as verified by extensive experimental comparison with the other learners. DataSqueezer is thus well suited to modern data mining and business intelligence tasks, which commonly involve huge datasets with a large fraction of missing data.

Measure Guideline: Transitioning from Three-Coat Stucco to One-Coat Stucco with EPS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Davis, G.; Rapport, A.

2012-04-01

This Measure Guideline has been developed to help builders transition from using a traditional three-coat stucco wall-cladding system to a one-coat stucco wall-cladding system with expanded polystyrene (EPS) insulated sheathing. The three-coat system uses a base layer, a fill layer, and a finish layer. The one-coat system maintains the look of a traditional stucco system but uses only a base layer and a finish coat over EPS insulation that achieves higher levels of energy efficiency. Potential risks associated with the installation of a one-coat stucco system are addressed in terms of design, installation, and warranty concerns such as cracking andmore » delamination, along with mitigation strategies to reduce these risks.« less

A framework for incorporating DTI Atlas Builder registration into Tract-Based Spatial Statistics and a simulated comparison to standard TBSS.

PubMed

Leming, Matthew; Steiner, Rachel; Styner, Martin

2016-02-27

Tract-based spatial statistics (TBSS) 6 is a software pipeline widely employed in comparative analysis of the white matter integrity from diffusion tensor imaging (DTI) datasets. In this study, we seek to evaluate the relationship between different methods of atlas registration for use with TBSS and different measurements of DTI (fractional anisotropy, FA, axial diffusivity, AD, radial diffusivity, RD, and medial diffusivity, MD). To do so, we have developed a novel tool that builds on existing diffusion atlas building software, integrating it into an adapted version of TBSS called DAB-TBSS (DTI Atlas Builder-Tract-Based Spatial Statistics) by using the advanced registration offered in DTI Atlas Builder 7 . To compare the effectiveness of these two versions of TBSS, we also propose a framework for simulating population differences for diffusion tensor imaging data, providing a more substantive means of empirically comparing DTI group analysis programs such as TBSS. In this study, we used 33 diffusion tensor imaging datasets and simulated group-wise changes in this data by increasing, in three different simulations, the principal eigenvalue (directly altering AD), the second and third eigenvalues (RD), and all three eigenvalues (MD) in the genu, the right uncinate fasciculus, and the left IFO. Additionally, we assessed the benefits of comparing the tensors directly using a functional analysis of diffusion tensor tract statistics (FADTTS 10 ). Our results indicate comparable levels of FA-based detection between DAB-TBSS and TBSS, with standard TBSS registration reporting a higher rate of false positives in other measurements of DTI. Within the simulated changes investigated here, this study suggests that the use of DTI Atlas Builder's registration enhances TBSS group-based studies.

Accessing the public MIMIC-II intensive care relational database for clinical research.

PubMed

Scott, Daniel J; Lee, Joon; Silva, Ikaro; Park, Shinhyuk; Moody, George B; Celi, Leo A; Mark, Roger G

2013-01-10

The Multiparameter Intelligent Monitoring in Intensive Care II (MIMIC-II) database is a free, public resource for intensive care research. The database was officially released in 2006, and has attracted a growing number of researchers in academia and industry. We present the two major software tools that facilitate accessing the relational database: the web-based QueryBuilder and a downloadable virtual machine (VM) image. QueryBuilder and the MIMIC-II VM have been developed successfully and are freely available to MIMIC-II users. Simple example SQL queries and the resulting data are presented. Clinical studies pertaining to acute kidney injury and prediction of fluid requirements in the intensive care unit are shown as typical examples of research performed with MIMIC-II. In addition, MIMIC-II has also provided data for annual PhysioNet/Computing in Cardiology Challenges, including the 2012 Challenge "Predicting mortality of ICU Patients". QueryBuilder is a web-based tool that provides easy access to MIMIC-II. For more computationally intensive queries, one can locally install a complete copy of MIMIC-II in a VM. Both publicly available tools provide the MIMIC-II research community with convenient querying interfaces and complement the value of the MIMIC-II relational database.

Big data analytics in immunology: a knowledge-based approach.

PubMed

Zhang, Guang Lan; Sun, Jing; Chitkushev, Lou; Brusic, Vladimir

2014-01-01

With the vast amount of immunological data available, immunology research is entering the big data era. These data vary in granularity, quality, and complexity and are stored in various formats, including publications, technical reports, and databases. The challenge is to make the transition from data to actionable knowledge and wisdom and bridge the knowledge gap and application gap. We report a knowledge-based approach based on a framework called KB-builder that facilitates data mining by enabling fast development and deployment of web-accessible immunological data knowledge warehouses. Immunological knowledge discovery relies heavily on both the availability of accurate, up-to-date, and well-organized data and the proper analytics tools. We propose the use of knowledge-based approaches by developing knowledgebases combining well-annotated data with specialized analytical tools and integrating them into analytical workflow. A set of well-defined workflow types with rich summarization and visualization capacity facilitates the transformation from data to critical information and knowledge. By using KB-builder, we enabled streamlining of normally time-consuming processes of database development. The knowledgebases built using KB-builder will speed up rational vaccine design by providing accurate and well-annotated data coupled with tailored computational analysis tools and workflow.

Changing imperatives of architecture affecting dimension stone use in world commerce

USGS Publications Warehouse

Mcdonald, W.H.; Darr, D.D.

1996-01-01

The use of stone in building construction predates written history. From the time that stone was first used, builders have constructed stone buildings predominately from local or regional materials. However, since World War II, the stone business has become increasingly global. For example, French limestone is now sold to builders in the United States, and American granite is shipped to Japan. The internationalization of architectural and construction firms has encouraged this trend. Differences among nations in trade practices, environmental demands and the level of knowledge of dimension-stone characteristics make international trading in stone a risky and potentially disastrous business for unwary participants.

[Bodybuilding: hypokalemia and hypophosphatemia].

PubMed

Britschgi, F; Zünd, G

1991-08-17

In preparing for competitive body building, body builders--in addition to continuous and hard muscle training--engage in stringent dietetic manipulations: the first few months of hypercaloric nutrition, rich in proteins, are devoted to the build-up of muscle mass. A second phase of reduced caloric intake is designed reduce subcutaneous fat, while, during the last week of preparations, extreme carbohydrate intake aims at loading muscles with glycogen. Simultaneously, sodium and water restriction results in extracellular and therefore subcutaneous volume deficit and better "definition" of muscle contours and structure. In the course of these dietetic manipulations a young body builder develops hypokalemia, hypophosphatemia, rhabdomyolysis and flaccid tetraparesis. The disturbances are pathophysiologically predictable.

Development of a platform-independent receiver control system for SISIFOS

NASA Astrophysics Data System (ADS)

Lemke, Roland; Olberg, Michael

1998-05-01

Up to now receiver control software was a time consuming development usually written by receiver engineers who had mainly the hardware in mind. We are presenting a low-cost and very flexible system which uses a minimal interface to the real hardware, and which makes it easy to adapt to new receivers. Our system uses Tcl/Tk as a graphical user interface (GUI), SpecTcl as a GUI builder, Pgplot as plotting software, a simple query language (SQL) database for information storage and retrieval, Ethernet socket to socket communication and SCPI as a command control language. The complete system is in principal platform independent but for cost saving reasons we are using it actually on a PC486 running Linux 2.0.30, which is a copylefted Unix. The only hardware dependent part are the digital input/output boards, analog to digital and digital to analog convertors. In the case of the Linux PC we are using a device driver development kit to integrate the boards fully into the kernel of the operating system, which indeed makes them look like an ordinary device. The advantage of this system is firstly the low price and secondly the clear separation between the different software components which are available for many operating systems. If it is not possible, due to CPU performance limitations, to run all the software in a single machine,the SQL-database or the graphical user interface could be installed on separate computers.

The Gene Set Builder: collation, curation, and distribution of sets of genes

PubMed Central

Yusuf, Dimas; Lim, Jonathan S; Wasserman, Wyeth W

2005-01-01

Background In bioinformatics and genomics, there are many applications designed to investigate the common properties for a set of genes. Often, these multi-gene analysis tools attempt to reveal sequential, functional, and expressional ties. However, while tremendous effort has been invested in developing tools that can analyze a set of genes, minimal effort has been invested in developing tools that can help researchers compile, store, and annotate gene sets in the first place. As a result, the process of making or accessing a set often involves tedious and time consuming steps such as finding identifiers for each individual gene. These steps are often repeated extensively to shift from one identifier type to another; or to recreate a published set. In this paper, we present a simple online tool which – with the help of the gene catalogs Ensembl and GeneLynx – can help researchers build and annotate sets of genes quickly and easily. Description The Gene Set Builder is a database-driven, web-based tool designed to help researchers compile, store, export, and share sets of genes. This application supports the 17 eukaryotic genomes found in version 32 of the Ensembl database, which includes species from yeast to human. User-created information such as sets and customized annotations are stored to facilitate easy access. Gene sets stored in the system can be "exported" in a variety of output formats – as lists of identifiers, in tables, or as sequences. In addition, gene sets can be "shared" with specific users to facilitate collaborations or fully released to provide access to published results. The application also features a Perl API (Application Programming Interface) for direct connectivity to custom analysis tools. A downloadable Quick Reference guide and an online tutorial are available to help new users learn its functionalities. Conclusion The Gene Set Builder is an Ensembl-facilitated online tool designed to help researchers compile and manage sets of genes in a user-friendly environment. The application can be accessed via . PMID:16371163

Response of general practitioners to computer-generated critiques of hypertension therapy.

PubMed

van der Lei, J; van der Does, E; Man in 't Veld, A J; Musen, M A; van Bemmel, J H

1993-04-01

We recently have shown that a computer system, known as HyperCritic, can successfully audit general practitioners' treatment of hypertension by analyzing computer-based patient records. HyperCritic reviews the electronic medical records and offers unsolicited advice. To determine which unsolicited advice might be perceived as inappropriate, builders of programs such as HyperCritic need insight into providers' responses to computer-generated critique of their patient care. Twenty medical charts, describing in total 243 visits of patients with hypertension, were audited by 8 human reviewers and by the critiquing-system HyperCritic. A panel of 14 general practitioners subsequently judged the relevance of those critiques on a five-point scale ranging from relevant critique to erroneous or harmful critique. The panel judged reviewers' comments to be either relevant or somewhat relevant in 61 to 68% of cases, and either erroneous or possibly erroneous in 15 to 18%; the panel judged HyperCritic's comments to be either relevant or somewhat relevant in 65% of cases, and either erroneous or possibly erroneous in 16%. Comparison of individual members of the panel showed large differences; for example, the portion of HyperCritic's comments judged relevant ranged from 0 to 82%. We conclude that, from the perspective of general practitioners, critiques generated by the critiquing system HyperCritic are perceived equally beneficial as critiques generated by human reviewers. Different general practitioners, however, judge the critiques differently. Before auditing systems based on computer-based patient records that are acceptable to practitioners can be introduced, additional studies are needed to evaluate the reasons a physician may have for judging critiques to be irrelevant, and to evaluate the effect of critiques on physician behavior.

KSC-04PD-0430

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers get ready to remove the protective cover from NASAs MESSENGER spacecraft. Employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0428

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. At the Astrotech Space Operations processing facilities near KSC, workers begin moving NASAs MESSENGER spacecraft into the building MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging is being taken into a high bay clean room where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0427

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. At the Astrotech Space Operations processing facilities near KSC, workers check the moveable pallet holding NASAs MESSENGER spacecraft. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be taken into a high bay clean room and employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0436

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare NASAs MESSENGER spacecraft for transfer to a work stand. There employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Integrated G and C Implementation within IDOS: A Simulink Based Reusable Launch Vehicle Simulation

NASA Technical Reports Server (NTRS)

Fisher, Joseph E.; Bevacqua, Tim; Lawrence, Douglas A.; Zhu, J. Jim; Mahoney, Michael

2003-01-01

The implementation of multiple Integrated Guidance and Control (IG&C) algorithms per flight phase within a vehicle simulation poses a daunting task to coordinate algorithm interactions with the other G&C components and with vehicle subsystems. Currently being developed by Universal Space Lines LLC (USL) under contract from NASA, the Integrated Development and Operations System (IDOS) contains a high fidelity Simulink vehicle simulation, which provides a means to test cutting edge G&C technologies. Combining the modularity of this vehicle simulation and Simulink s built-in primitive blocks provide a quick way to implement algorithms. To add discrete-event functionality to the unfinished IDOS simulation, Vehicle Event Manager (VEM) and Integrated Vehicle Health Monitoring (IVHM) subsystems were created to provide discrete-event and pseudo-health monitoring processing capabilities. Matlab's Stateflow is used to create the IVHM and Event Manager subsystems and to implement a supervisory logic controller referred to as the Auto-commander as part of the IG&C to coordinate the control system adaptation and reconfiguration and to select the control and guidance algorithms for a given flight phase. Manual creation of the Stateflow charts for all of these subsystems is a tedious and time-consuming process. The Stateflow Auto-builder was developed as a Matlab based software tool for the automatic generation of a Stateflow chart from information contained in a database. This paper describes the IG&C, VEM and IVHM implementations in IDOS. In addition, this paper describes the Stateflow Auto-builder.

Applications of Dynamic Deployment of Services in Industrial Automation

NASA Astrophysics Data System (ADS)

Candido, Gonçalo; Barata, José; Jammes, François; Colombo, Armando W.

Service-oriented Architecture (SOA) is becoming a de facto paradigm for business and enterprise integration. SOA is expanding into several domains of application envisioning a unified solution suitable across all different layers of an enterprise infrastructure. The application of SOA based on open web standards can significantly enhance the interoperability and openness of those devices. By embedding a dynamical deployment service even into small field de- vices, it would be either possible to allow machine builders to place built- in services and still allow the integrator to deploy on-the-run the services that best fit his current application. This approach allows the developer to keep his own preferred development language, but still deliver a SOA- compliant application. A dynamic deployment service is envisaged as a fundamental framework to support more complex applications, reducing deployment delays, while increasing overall system agility. As use-case scenario, a dynamic deployment service was implemented over DPWS and WS-Management specifications allowing designing and programming an automation application using IEC61131 languages, and deploying these components as web services into devices.

Building energy analysis of Electrical Engineering Building from DesignBuilder tool: calibration and simulations

NASA Astrophysics Data System (ADS)

Cárdenas, J.; Osma, G.; Caicedo, C.; Torres, A.; Sánchez, S.; Ordóñez, G.

2016-07-01

This research shows the energy analysis of the Electrical Engineering Building, located on campus of the Industrial University of Santander in Bucaramanga - Colombia. This building is a green pilot for analysing energy saving strategies such as solar pipes, green roof, daylighting, and automation, among others. Energy analysis was performed by means of DesignBuilder software from virtual model of the building. Several variables were analysed such as air temperature, relative humidity, air velocity, daylighting, and energy consumption. According to two criteria, thermal load and energy consumption, critical areas were defined. The calibration and validation process of the virtual model was done obtaining error below 5% in comparison with measured values. The simulations show that the average indoor temperature in the critical areas of the building was 27°C, whilst relative humidity reached values near to 70% per year. The most critical discomfort conditions were found in the area of the greatest concentration of people, which has an average annual temperature of 30°C. Solar pipes can increase 33% daylight levels into the areas located on the upper floors of the building. In the case of the green roofs, the simulated results show that these reduces of nearly 31% of the internal heat gains through the roof, as well as a decrease in energy consumption related to air conditioning of 5% for some areas on the fourth and fifth floor. The estimated energy consumption of the building was 69 283 kWh per year.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andre, J.M.; et al.

The data acquisition system (DAQ) of the CMS experiment at the CERN Large Hadron Collider assembles events at a rate of 100 kHz, transporting event data at an aggregate throughput of to the high-level trigger farm. The DAQ architecture is based on state-of-the-art network technologies for the event building. For the data concentration, 10/40 Gbit/s Ethernet technologies are used together with a reduced TCP/IP protocol implemented in FPGA for a reliable transport between custom electronics and commercial computing hardware. A 56 Gbit/s Infiniband FDR Clos network has been chosen for the event builder. This paper presents the implementation and performancemore » of the event-building system.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Building cost effective, high performance homes that provide superior comfort, health, and durability is the goal of the Department of Energy's (DOE's) Zero Energy Ready Homes (ZERH) program. Through Building America research and other innovative programs throughout the country, many of the technical challenges to building to the ZERH standard have been addressed. This case study describes the development of a 62-unit multifamily community constructed by nonprofit developer Mutual Housing at the Spring Lake subdivision in Woodland, CA. The Spring Lake project is expected to be the first ZERH-certified multifamily project nationwide. Building America team Alliance for Residential Building Innovationmore » worked with Mutual Housing throughout the project. The case study discusses challenges encountered, lessons learned, and how obstacles were overcome. An objective of this project was to gain a highly visible foothold for residential buildings built to the DOE ZERH specification that can be used to encourage participation by other California builders.« less

Sharing Health Big Data for Research - A Design by Use Cases: The INSHARE Platform Approach.

PubMed

Bouzillé, Guillaume; Westerlynck, Richard; Defossez, Gautier; Bouslimi, Dalel; Bayat, Sahar; Riou, Christine; Busnel, Yann; Le Guillou, Clara; Cauvin, Jean-Michel; Jacquelinet, Christian; Pladys, Patrick; Oger, Emmanuel; Stindel, Eric; Ingrand, Pierre; Coatrieux, Gouenou; Cuggia, Marc

2017-01-01

Sharing and exploiting Health Big Data (HBD) allow tackling challenges: data protection/governance taking into account legal, ethical, and deontological aspects enables trust, transparent and win-win relationship between researchers, citizens, and data providers. Lack of interoperability: compartmentalized and syntactically/semantica heterogeneous data. INSHARE project using experimental proof of concept explores how recent technologies overcome such issues. Using 6 data providers, platform is designed via 3 steps to: (1) analyze use cases, needs, and requirements; (2) define data sharing governance, secure access to platform; and (3) define platform specifications. Three use cases - from 5 studies and 11 data sources - were analyzed for platform design. Governance derived from SCANNER model was adapted to data sharing. Platform architecture integrates: data repository and hosting, semantic integration services, data processing, aggregate computing, data quality and integrity monitoring, Id linking, multisource query builder, visualization and data export services, data governance, study management service and security including data watermarking.

LEGO products have become more complex

PubMed Central

2018-01-01

The LEGO Group has become the largest toy company in the world and they can look back to a proud history of more than 50 years of producing bricks and other toys. Starting with a simple set of basic bricks their range of toys appeared to have increased in complexity over the years. We processed the inventories of most sets from 1955–2015 and our analysis showed that LEGO sets have become bigger, more colorful and more specialized. The vocabulary of bricks has increased significantly resulting in sets sharing fewer bricks. The increased complexity of LEGO sets and bricks enables skilled builders to design ever more amazing models but it may also overwhelm less skilled or younger builders. PMID:29293655

LEGO products have become more complex.

PubMed

Bartneck, Christoph; Moltchanova, Elena

2018-01-01

The LEGO Group has become the largest toy company in the world and they can look back to a proud history of more than 50 years of producing bricks and other toys. Starting with a simple set of basic bricks their range of toys appeared to have increased in complexity over the years. We processed the inventories of most sets from 1955-2015 and our analysis showed that LEGO sets have become bigger, more colorful and more specialized. The vocabulary of bricks has increased significantly resulting in sets sharing fewer bricks. The increased complexity of LEGO sets and bricks enables skilled builders to design ever more amazing models but it may also overwhelm less skilled or younger builders.

TRUSTBUILDER2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Adam J.; Perano, Kenneth J.

In trust negotiation, resource providers specify access control policies in terms of the attributes that should be possessed by authorized users, rather than the identities of these users. Users can prove ownership of certain attributes through the use of digital credentials issued by trusted entities. For example, the Department of Motor Vehicles might issue vehicle owners X.509 driver's licenses that can be used to demonstrate proof of their current age, address, or ability to drive. These types of digital credentials may also be protected by user-specified policies controlling their release to remote parties; for example, Alice might only be willingmore » to show her VISA card credential to members of the Better Business Bureau. In this way, a request to access a given resource can result in a bilateral and iterative exchange of policies and credentials that represents a negotiation between the participating parties. To date, research interest in trust negotiation has been primarily theoretical and any implementations have been largely proofs of concept; experimenting with these prototypes is often not a straightforward task. TrustBuilder2 is a flexible framework for supporting research in the area trust negotiation protocols, designed to allow researchers to quickly prototype and experiment with various approaches to trust negotiation. In TrustBuilder2, the primary components of a trust negotiation system are represented using abstract interfaces.« less

Constructing a Database from Multiple 2D Images for Camera Pose Estimation and Robot Localization

NASA Technical Reports Server (NTRS)

Wolf, Michael; Ansar, Adnan I.; Brennan, Shane; Clouse, Daniel S.; Padgett, Curtis W.

2012-01-01

The LMDB (Landmark Database) Builder software identifies persistent image features (landmarks) in a scene viewed multiple times and precisely estimates the landmarks 3D world positions. The software receives as input multiple 2D images of approximately the same scene, along with an initial guess of the camera poses for each image, and a table of features matched pair-wise in each frame. LMDB Builder aggregates landmarks across an arbitrarily large collection of frames with matched features. Range data from stereo vision processing can also be passed to improve the initial guess of the 3D point estimates. The LMDB Builder aggregates feature lists across all frames, manages the process to promote selected features to landmarks, and iteratively calculates the 3D landmark positions using the current camera pose estimations (via an optimal ray projection method), and then improves the camera pose estimates using the 3D landmark positions. Finally, it extracts image patches for each landmark from auto-selected key frames and constructs the landmark database. The landmark database can then be used to estimate future camera poses (and therefore localize a robotic vehicle that may be carrying the cameras) by matching current imagery to landmark database image patches and using the known 3D landmark positions to estimate the current pose.

Accessing the public MIMIC-II intensive care relational database for clinical research

PubMed Central

2013-01-01

Background The Multiparameter Intelligent Monitoring in Intensive Care II (MIMIC-II) database is a free, public resource for intensive care research. The database was officially released in 2006, and has attracted a growing number of researchers in academia and industry. We present the two major software tools that facilitate accessing the relational database: the web-based QueryBuilder and a downloadable virtual machine (VM) image. Results QueryBuilder and the MIMIC-II VM have been developed successfully and are freely available to MIMIC-II users. Simple example SQL queries and the resulting data are presented. Clinical studies pertaining to acute kidney injury and prediction of fluid requirements in the intensive care unit are shown as typical examples of research performed with MIMIC-II. In addition, MIMIC-II has also provided data for annual PhysioNet/Computing in Cardiology Challenges, including the 2012 Challenge “Predicting mortality of ICU Patients”. Conclusions QueryBuilder is a web-based tool that provides easy access to MIMIC-II. For more computationally intensive queries, one can locally install a complete copy of MIMIC-II in a VM. Both publicly available tools provide the MIMIC-II research community with convenient querying interfaces and complement the value of the MIMIC-II relational database. PMID:23302652

Approaches to 30% Energy Savings at the Community Scale in the Hot-Humid Climate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas-Rees, S.; Beal, D.; Martin, E.

2013-03-01

BA-PIRC has worked with several community-scale builders within the hot humid climate zone to improve performance of production, or community scale, housing. Tommy Williams Homes (Gainesville, FL), Lifestyle Homes (Melbourne, FL), and Habitat for Humanity (various locations, FL) have all been continuous partners of the BA Program and are the subjects of this report to document achievement of the Building America goal of 30% whole house energy savings packages adopted at the community scale. The scope of this report is to demonstrate achievement of these goals though the documentation of production-scale homes built cost-effectively at the community scale, and modeledmore » to reduce whole-house energy use by 30% in the Hot Humid climate region. Key aspects of this research include determining how to evolve existing energy efficiency packages to produce replicable target savings, identifying what builders' technical assistance needs are for implementation and working with them to create sustainable quality assurance mechanisms, and documenting the commercial viability through neutral cost analysis and market acceptance. This report documents certain barriers builders overcame and the approaches they implemented in order to accomplish Building America (BA) Program goals that have not already been documented in previous reports.« less

Effects of supported electronic text and explicit instruction on science comprehension by students with autism spectrum disorder

NASA Astrophysics Data System (ADS)

Knight, Victoria Floyd

Supported electronic text (eText), or text that has been altered to increase access and provide support to learners, may promote comprehension of science content for students with disabilities. According to CAST, Book Builder(TM) uses supported eText to promote reading for meaning for all students. Although little research has been conducted in the area of supported eText for students with autism spectrum disorders (ASD), technology (e.g., computer assisted instruction) has been used for over 35 years to instruct students with ASD in academic areas. The purpose of this study was to evaluate the effects of a supported eText and explicit instruction on the science vocabulary and comprehension of four middle school students with ASD. Researchers used a multiple probe across participants design to evaluate the Book Builder (TM) program on measures of vocabulary, literal comprehension, and application questions. Results indicated a functional relation between the Book Builder(TM) and explicit instruction (i.e., model-lead-test, examples and non-examples, and referral to the definition) and the number of correct responses on the probe. In addition, students were able to generalize concepts to untrained exemplars. Finally, teachers and students validate the program as practical and useful.

Lipoprotein profile, diet and body composition in athletes practicing mixed an anaerobic activities.

PubMed

Giada, F; Zuliani, G; Baldo-Enzi, G; Palmieri, E; Volpato, S; Vitale, E; Magnanini, P; Colozzi, A; Vecchiet, L; Fellin, R

1996-09-01

To compare lipoprotein profile, body composition and diet in a sample of athletes practicing mixed and anaerobic sports activities, and in a group of sedentary controls. Cross selectional study. Twenty professional soccer players (mixed trained), twenty body builders (anaerobic trained) and twenty sedentary subjects, all males and matched for age were studied. No significant differences in total serum cholesterol, triglycerides, HDL-C, LDL-C, apolipoprotein A-I, A-II, B, C-II, C-III, and E levels were found when the three groups were compared. Bioelectrical impendance analysis disclosed significantly lower body fat percentages in both groups of athletes, and increased fat free mass only in body builders. Daily calorie intake was higher, and alcohol intake was lower in the athletes, compared with controls. Body builders had lower carbohydrate, and higher protein and cholesterol intakes, while soccer players had a lower polyunsaturated to saturated fat ratio. None of the apolipoproteins examined was correlated with any body composition of diet parameters. No correlations between lipid parameters and anthropometric or dietary variables were found by multivariate analysis when the subjects were considered as a whole. Our data suggest that in healthy lean normolipemic males, the lipoprotein profile is not modified by mixed or anaerobic sport activities and the respective modifications in body composition and diet.

Continuation of research in software for space operations support

NASA Technical Reports Server (NTRS)

Collier, Mark D.

1989-01-01

Software technologies relevant to workstation executives are discussed. Evaluations of problems, potential or otherwise, seen with IBM's Workstation Executive (WEX) 2.5 preliminary design and applicable portions of the 2.5 critical design are presented. Diverse graphics requirements of the Johnson Space Center's Mission Control Center Upgrade (MCCU) are also discussed. The key is to use tools that are portable, compatible with the X window system, and best suited to the requirements of the associated application. This will include a User Interface Language (UIL), an interactive display builder, and a graphic plotting/modeling system. Work sheets are provided for POSIX 1003.4 real-time extensions and the requirements for the Center's automated information systems security plan, referred to as POSIX 1003.6, are discussed.

KSC-04PD-0435

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers attach an overhead crane to NASAs MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

KSC-04PD-0434

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. In the high bay clean room at the Astrotech Space Operations processing facilities near KSC, workers prepare to attach an overhead crane to NASAs MESSENGER spacecraft. The spacecraft will be moved to a work stand where employees of the Johns Hopkins University Applied Physics Laboratory, builders of the spacecraft, will perform an initial state-of-health check. Then processing for launch can begin, including checkout of the power systems, communications systems and control systems. The thermal blankets will also be attached for flight. MESSENGER short for MErcury Surface, Space ENvironment, GEochemistry and Ranging will be launched May 11 on a six-year mission aboard a Boeing Delta II rocket. Liftoff is targeted for 2:26 a.m. EDT on Tuesday, May 11.

Enriching the Web Processing Service

NASA Astrophysics Data System (ADS)

Wosniok, Christoph; Bensmann, Felix; Wössner, Roman; Kohlus, Jörn; Roosmann, Rainer; Heidmann, Carsten; Lehfeldt, Rainer

2014-05-01

The OGC Web Processing Service (WPS) provides a standard for implementing geospatial processes in service-oriented networks. In its current version 1.0.0 it allocates the operations GetCapabilities, DescribeProcess and Execute, which can be used to offer custom processes based on single or multiple sub-processes. A large range of ready to use fine granular, fundamental geospatial processes have been developed by the GIS-community in the past. However, modern use cases or whole workflow processes demand specifications of lifecycle management and service orchestration. Orchestrating smaller sub-processes is a task towards interoperability; a comprehensive documentation by using appropriate metadata is also required. Though different approaches were tested in the past, developing complex WPS applications still requires programming skills, knowledge about software libraries in use and a lot of effort for integration. Our toolset RichWPS aims at providing a better overall experience by setting up two major components. The RichWPS ModelBuilder enables the graphics-aided design of workflow processes based on existing local and distributed processes and geospatial services. Once tested by the RichWPS Server, a composition can be deployed for production use on the RichWPS Server. The ModelBuilder obtains necessary processes and services from a directory service, the RichWPS semantic proxy. It manages the lifecycle and is able to visualize results and debugging-information. One aim will be to generate reproducible results; the workflow should be documented by metadata that can be integrated in Spatial Data Infrastructures. The RichWPS Server provides a set of interfaces to the ModelBuilder for, among others, testing composed workflow sequences, estimating their performance and to publish them as common processes. Therefore the server is oriented towards the upcoming WPS 2.0 standard and its ability to transactionally deploy and undeploy processes making use of a WPS-T interface. In order to deal with the results of these processing workflows, a server side extension enables the RichWPS Server and its clients to use WPS presentation directives (WPS-PD), a content related enhancement for the standardized WPS schema. We identified essential requirements of the components of our toolset by applying two use cases. The first enables the simplified comparison of modeled and measured data, a common task in hydro-engineering to validate the accuracy of a model. An implementation of the workflow includes reading, harmonizing and comparing two datasets in NetCDF-format. 2D Water level data from the German Bight can be chosen, presented and evaluated in a web client with interactive plots. The second use case is motivated by the Marine Strategy Directive (MSD) of the EU, which demands monitoring, action plans and at least an evaluation of the ecological situation in marine environment. Information technics adapted to those of INSPIRE should be used. One of the parameters monitored and evaluated for MSD is the expansion and quality of seagrass fields. With the view towards other evaluation parameters we decompose the complex process of evaluation of seagrass in reusable process steps and implement those packages as configurable WPS.

Comparative Cooling Season Performance of Air Distribution Systems in Multistory Townhomes

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. Poerschke; Beach, R.; Beggs, T.

2016-08-26

IBACOS investigated the performance of a small-diameter high velocity heat pump system compared to a conventional system in a new construction triplex townhouse. A ductless heat pump system also was installed for comparison, but the homebuyer backed out because of aesthetic concerns about that system. In total, two buildings, having identical solar orientation and comprised of six townhomes, were monitored for comfort and energy performance. Results show that the small-diameter system provides more uniform temperatures from floor to floor in the three-story townhome. No clear energy consumption benefit was observed from either system. The builder is continuing to explore themore » small-diameter system as its new standard system to provide better comfort and indoor air quality. The homebuilder also explored the possibility of shifting its townhome product to meet the U.S. Department of Energy Challenge Home National Program Requirements.« less

Prototype of smart office system using based security system

NASA Astrophysics Data System (ADS)

Prasetyo, T. F.; Zaliluddin, D.; Iqbal, M.

2018-05-01

Creating a new technology in the modern era gives a positive impact on business and industry. Internet of Things (IoT) as a new communication technology is very useful in realizing smart systems such as: smart home, smart office, smart parking and smart city. This study presents a prototype of the smart office system which was designed as a security system based on IoT. Smart office system development method used waterfall model. IoT-based smart office system used platform (project builder) cayenne so that. The data can be accessed and controlled through internet network from long distance. Smart office system used arduino mega 2560 microcontroller as a controller component. In this study, Smart office system is able to detect threats of dangerous objects made from metals, earthquakes, fires, intruders or theft and perform security monitoring outside the building by using raspberry pi cameras on autonomous robots in real time to the security guard.

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The builder worked with Building Science Corporation to design ten HERS 53 homes with ICF foundations, foam-sheathed above-grade walls, and high-efficiency furnaces with fresh air intake and jump ducts.

Real-time immune-inspired optimum state-of-charge trajectory estimation using upcoming route information preview and neural networks for plug-in hybrid electric vehicles fuel economy

NASA Astrophysics Data System (ADS)

Mozaffari, Ahmad; Vajedi, Mahyar; Azad, Nasser L.

2015-06-01

The main proposition of the current investigation is to develop a computational intelligence-based framework which can be used for the real-time estimation of optimum battery state-of-charge (SOC) trajectory in plug-in hybrid electric vehicles (PHEVs). The estimated SOC trajectory can be then employed for an intelligent power management to significantly improve the fuel economy of the vehicle. The devised intelligent SOC trajectory builder takes advantage of the upcoming route information preview to achieve the lowest possible total cost of electricity and fossil fuel. To reduce the complexity of real-time optimization, the authors propose an immune system-based clustering approach which allows categorizing the route information into a predefined number of segments. The intelligent real-time optimizer is also inspired on the basis of interactions in biological immune systems, and is called artificial immune algorithm (AIA). The objective function of the optimizer is derived from a computationally efficient artificial neural network (ANN) which is trained by a database obtained from a high-fidelity model of the vehicle built in the Autonomie software. The simulation results demonstrate that the integration of immune inspired clustering tool, AIA and ANN, will result in a powerful framework which can generate a near global optimum SOC trajectory for the baseline vehicle, that is, the Toyota Prius PHEV. The outcomes of the current investigation prove that by taking advantage of intelligent approaches, it is possible to design a computationally efficient and powerful SOC trajectory builder for the intelligent power management of PHEVs.

Building America Industrialized Housing Partnership (BAIHP II)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abernethy, Bob; Chandra, Subrato; Baden, Steven

2010-11-30

This report summarizes the work conducted by the Building America Industrialized Housing Partnership (BAIHP - www.baihp.org) during the final budget period (BP5) of our contract, January 1, 2010 to November 30, 2010. Highlights from the four previous budget periods are included for context. BAIHP is led by the Florida Solar Energy Center (FSEC) of the University of Central Florida. With over 50 Industry Partners including factory and site builders, work in BP5 was performed in six tasks areas: Building America System Research Management, Documentation and Technical Support; System Performance Evaluations; Prototype House Evaluations; Initial Community Scale Evaluations; Project Closeout, Finalmore » Review of BA Communities; and Other Research Activities.« less

Structural Dynamics of Carbon Dots in Water and N, N-Dimethylformamide Probed by All-Atom Molecular Dynamics Simulations.

PubMed

Paloncýová, Markéta; Langer, Michal; Otyepka, Michal

2018-04-10

Carbon dots (CDs), one of the youngest members of the carbon nanostructure family, are now widely experimentally studied for their tunable fluorescence properties, bleaching resistance, and biocompatibility. Their interaction with biomolecular systems has also been explored experimentally. However, many atomistic details still remain unresolved. Molecular dynamics (MD) simulations enabling atomistic and femtosecond resolutions simultaneously are a well-established tool of computational chemistry which can provide useful insights into investigated systems. Here we present a full procedure for performing MD simulations of CDs. We developed a builder for generating CDs of a desired size and with various oxygen-containing surface functional groups. Further, we analyzed the behavior of various CDs differing in size, surface functional groups, and degrees of functionalization by MD simulations. These simulations showed that surface functionalized CDs are stable in a water environment through the formation of an extensive hydrogen bonding network. We also analyzed the internal dynamics of individual layers of CDs and evaluated the role of surface functional groups on CD stability. We observed that carboxyl groups interconnected the neighboring layers and decreased the rate of internal rotations. Further, we monitored changes in the CD shape caused by an excess of charged carboxyl groups or carbonyl groups. In addition to simulations in water, we analyzed the behavior of CDs in the organic solvent DMF, which decreased the stability of pure CDs but increased the level of interlayer hydrogen bonding. We believe that the developed protocol, builder, and parameters will facilitate future studies addressing various aspects of structural features of CDs and nanocomposites containing CDs.

Meteore 63 commercial seaplane

NASA Technical Reports Server (NTRS)

1927-01-01

Societe Provencale de Constructions Aeronautiques, builder of the "Meteore 63" has constructed a three engine (biplane) seaplane which has met conditions for a seaworthy certificate of the first class.

Atomdroid: a computational chemistry tool for mobile platforms.

PubMed

Feldt, Jonas; Mata, Ricardo A; Dieterich, Johannes M

2012-04-23

We present the implementation of a new molecular mechanics program designed for use in mobile platforms, the first specifically built for these devices. The software is designed to run on Android operating systems and is compatible with several modern tablet-PCs and smartphones available in the market. It includes molecular viewer/builder capabilities with integrated routines for geometry optimizations and Monte Carlo simulations. These functionalities allow it to work as a stand-alone tool. We discuss some particular development aspects, as well as the overall feasibility of using computational chemistry software packages in mobile platforms. Benchmark calculations show that through efficient implementation techniques even hand-held devices can be used to simulate midsized systems using force fields.

DOE Zero Energy Ready Home Case Study: Amaris Custom Homes, St. Paul, Minnesota

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

For this project, Amaris worked with U.S. Department of Energy (DOE) team, NorthernSTAR Building America Partnership, to develop the first Zero Energy Ready Home (ZERH) in Minnesota's cold climate using reasonable, cost-effective, and replicable construction materials and practices. The result is a passive solar, super-efficient 3542-ft2 walkout ranch-style home with all the creature comforts. Along with meeting ZERH standards, Amaris also achieved certifications for Leadership in Energy & Environmental Design for Homes v4, MN Green Path Emerald, and a Builders Association of the Twin Cities Reggie Award of Excellence. The home achieves a HERS score of 41 without photovoltaics; withmore » PV, the home achieves a HERS score of 5.« less

Research on crude oil storage and transportation based on optimization algorithm

NASA Astrophysics Data System (ADS)

Yuan, Xuhua

2018-04-01

At present, the optimization theory and method have been widely used in the optimization scheduling and optimal operation scheme of complex production systems. Based on C++Builder 6 program development platform, the theoretical research results are implemented by computer. The simulation and intelligent decision system of crude oil storage and transportation inventory scheduling are designed. The system includes modules of project management, data management, graphics processing, simulation of oil depot operation scheme. It can realize the optimization of the scheduling scheme of crude oil storage and transportation system. A multi-point temperature measuring system for monitoring the temperature field of floating roof oil storage tank is developed. The results show that by optimizing operating parameters such as tank operating mode and temperature, the total transportation scheduling costs of the storage and transportation system can be reduced by 9.1%. Therefore, this method can realize safe and stable operation of crude oil storage and transportation system.

Building America Case Study: Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings, Upstate New York (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2014-11-01

While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient by itself. In addition, the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-risemore » multifamily dwellings. While this air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of CARB's multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in 3 multifamily buildings.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herk, A.; Poerschke, A.; Beach, R.

In 2012-2013, IBACOS worked with a builder, Brookfield Homes in Denver, Colorado, to design and construct a Passive House certified model home. IBACOS used several modeling programs and calculation methods to complete the final design package along with Brookfield's architect KGA Studio. This design package included upgrades to the thermal enclosure, basement insulation, windows, and heating, ventilation, and air conditioning. Short-term performance testing in the Passive House was done during construction and after construction. Testing with a blower door indicated that whole-building air leakage to the outside was 324 CFM and 0.60 ACH50. The other two test homes had littlemore » short-term testing done post-construction by the local energy rater. IBACOS then monitored the energy consumption and whole-house comfort conditions of that occupied Passive House after one year of operation and compared the monitoring results to those for two other occupied test houses in the same area with similar square footage but slightly different floor plans. IBACOS also assisted the builder, Brookfield Homes, in researching design scenarios for Zero Energy Ready Home and ENERGY STAR acceptance levels. IBACOS also assisted Brookfield in conceptualizing product for Denver's Brighton Heights area. Brookfield was considering building to Zero Energy Ready Home standards in that location. IBACOS provided strategies that Brookfield may draw from in the event the builder chooses to pursue a Zero Energy Ready Home plan for that market.« less

Serenbe Nest Cottages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Kim, E.

2012-12-01

As part of the NAHB Research Center Industry Partnership, Southface partnered with Martin Dodson Builders and the Serenbe community on the construction of a new test home in the suburbs of Atlanta, GA, in the mixed humid climate zone. The most recent subdivision within the Serenbe community, the Nest, will contain 15 small footprint cottage-style homes, and Southface has selected Lot Nine, as the test home for this study. This Nest subdivision serves as a project showcase for both the builder partner and the Serenbe community as a whole. The planning and design incorporated into the Nest cottages will bemore » implemented in each home within the subdivision. These homes addresses Building America savings targets and serve as a basis of design for other homes Martin Dodson plans to build within the Serenbe community.« less

Serenbe Nest Cottages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, T.; Curtis, O.; Kim, E.

2012-12-01

As part of the NAHB Research Center Industry Partnership, Southface partnered with Martin Dodson Builders and the Serenbe community on the construction of a new test home in the suburbs of Atlanta, GA in the mixed humid climate zone. The most recent subdivision within the Serenbe community, the Nest, will contain 15 small footprint cottage style homes, and Southface has selected Lot Nine, as the test home for this study. This Nest subdivision serves as a project showcase for both the builder partner and the Serenbe community as a whole. The planning and design incorporated into the Nest cottages willmore » be implemented in each home within the subdivision. These homes addresses Building America Savings targets and serve as a basis of design for other homes Martin Dodson plans to build within the Serenbe community.« less

Applications of a morphological scene change detection (MSCD) for visual leak and failure identification in process and chemical engineering

NASA Astrophysics Data System (ADS)

Tickle, Andrew J.; Harvey, Paul K.; Smith, Jeremy S.

2010-10-01

Morphological Scene Change Detection (MSCD) is a process typically tasked at detecting relevant changes in a guarded environment for security applications. This can be implemented on a Field Programmable Gate Array (FPGA) by a combination of binary differences based around exclusive-OR (XOR) gates, mathematical morphology and a crucial threshold setting. The additional ability to set up the system in virtually any location due to the FPGA makes it ideal for insertion into an autonomous mobile robot for patrol duties. However, security is not the only potential of this robust algorithm. This paper details how such a system can be used for the detection of leaks in piping for use in the process and chemical industries and could be deployed as stated in the above manner. The test substance in this work was water, which was pumped either as a liquid or as low pressure steam through a simple pipe configuration with holes at set points to simulate the leaks. These holes were situated randomly at either the center of a pipe (in order to simulate an impact to it) or at a joint or corner (to simulate a failed weld). Imagery of the resultant leaks, which were visualised as drips or the accumulation of steam, which where analysed using MATLAB to determine their pixel volume in order to calibrate the trigger for the MSCD. The triggering mechanism is adaptive to make it possible in theory for the type of leak to be determined by the number of pixels in the threshold of the image and a numerical output signal to state which of the leak situations is being observed. The system was designed using the DSP Builder package from Altera so that its graphical nature is easily comprehensible to the non-embedded system designer. Furthermore, all the data from the DSP Builder simulation underwent verification against MATLAB comparisons using the image processing toolbox in order to validate the results.

Are coral reefs victims of their own past success?

PubMed

Renema, Willem; Pandolfi, John M; Kiessling, Wolfgang; Bosellini, Francesca R; Klaus, James S; Korpanty, Chelsea; Rosen, Brian R; Santodomingo, Nadiezhda; Wallace, Carden C; Webster, Jody M; Johnson, Kenneth G

2016-04-01

As one of the most prolific and widespread reef builders, the staghorn coral Acropora holds a disproportionately large role in how coral reefs will respond to accelerating anthropogenic change. We show that although Acropora has a diverse history extended over the past 50 million years, it was not a dominant reef builder until the onset of high-amplitude glacioeustatic sea-level fluctuations 1.8 million years ago. High growth rates and propagation by fragmentation have favored staghorn corals since this time. In contrast, staghorn corals are among the most vulnerable corals to anthropogenic stressors, with marked global loss of abundance worldwide. The continued decline in staghorn coral abundance and the mounting challenges from both local stress and climate change will limit the coral reefs' ability to provide ecosystem services.

Are coral reefs victims of their own past success?

PubMed Central

Renema, Willem; Pandolfi, John M.; Kiessling, Wolfgang; Bosellini, Francesca R.; Klaus, James S.; Korpanty, Chelsea; Rosen, Brian R.; Santodomingo, Nadiezhda; Wallace, Carden C.; Webster, Jody M.; Johnson, Kenneth G.

2016-01-01

As one of the most prolific and widespread reef builders, the staghorn coral Acropora holds a disproportionately large role in how coral reefs will respond to accelerating anthropogenic change. We show that although Acropora has a diverse history extended over the past 50 million years, it was not a dominant reef builder until the onset of high-amplitude glacioeustatic sea-level fluctuations 1.8 million years ago. High growth rates and propagation by fragmentation have favored staghorn corals since this time. In contrast, staghorn corals are among the most vulnerable corals to anthropogenic stressors, with marked global loss of abundance worldwide. The continued decline in staghorn coral abundance and the mounting challenges from both local stress and climate change will limit the coral reefs’ ability to provide ecosystem services. PMID:27152330

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The first Challenge Home built in New England features cool-roof shingles, HERS 20–42, and walls densely packed with blown fiberglass. This house won a 2013 Housing Innovation Award in the custom builder category.

Mars Rover Concept Vehicle

NASA Image and Video Library

2017-06-05

The scientifically-themed Mars rover concept vehicle operates on an electric motor, powered by solar panels and a 700-volt battery. The rover separates in the middle with the front area designed for scouting and equipped with a radio and navigation provided by the Global Positioning System. The back section serves as a full laboratory which can disconnect for autonomous research. The "Summer of Mars" promotion is designed to provide guests with a better understanding of NASA's studies of the Red Planet. The builders of the rover, Parker Brothers Concepts of Port Canaveral, Florida, incorporated input into its design from NASA subject matter experts.

Systems definition study for shuttle demonstration flights of large space structures, Volume 2: Technical Report

NASA Technical Reports Server (NTRS)

1979-01-01

The development of large space structure (LSS) technology is discussed, with emphasis on space fabricated structures which are automatically manufactured in space from sheet-strip materials and assembled on-orbit. It is concluded that an LSS flight demonstration using an Automated Beam Builder and the orbiter as a construction base, could be performed in the 1983-1984 time period. The estimated cost is $24 million exclusive of shuttle launch costs. During the mission, a simple space platform could be constructed in-orbit to accommodate user requirements associated with earth viewing and materials exposure experiments needs.

The Infinite in the Finite

NASA Astrophysics Data System (ADS)

Macintosh Wilson, Alistair

1996-01-01

A conversation between Euclid and the ghost of Socrates. . . the paths of the moon and the sun charted by the stone-builders of ancient Europe. . .the Greek ideal of the golden mean by which they measured beauty. . . Combining historical fact with a retelling of ancient myths and legends, this lively and engaging book describes the historical, religious and geographical background that gave rise to mathematics in ancient Egypt, Babylon, China, Greece, India, and the Arab world. Each chapter contains a case study where mathematics is applied to the problems of the era, including the area of triangles and volume of the Egyptian pyramids; the Babylonian sexagesimal number system and our present measure of space and time which grew out of it; the use of the abacus and remainder theory in China; the invention of trigonometry by Arab mathematicians; and the solution of quadratic equations by completing the square developed in India. These insightful commentaries will give mathematicians and general historians a better understanding of why and how mathematics arose from the problems of everyday life, while the author's easy, accessible writing style will open fascinating chapters in the history of mathematics to a wide audience of general readers.

Synergic effects of thermal mass and natural ventilation on the thermal behaviour of traditional massive buildings

NASA Astrophysics Data System (ADS)

Gagliano, A.; Nocera, F.; Patania, F.; Moschella, A.; Detommaso, M.; Evola, G.

2016-05-01

The energy policies about energy efficiency in buildings currently focus on new buildings and on existing buildings in case of energy retrofit. However, historic and heritage buildings, that are the trademark of numerous European cities, should also deserve attention; nevertheless, their energy efficiency is nowadays not deeply investigated. In this context, this study evaluates the thermal performance of a traditional massive building situated in a Mediterranean city. Dynamic numerical simulations were carried out on a yearly basis through the software DesignBuilder, both in free-running conditions and in the presence of an air-conditioning (AC) system. The results highlight that the massive envelope of traditional residential buildings helps in maintaining small fluctuations of the indoor temperature, thus limiting the need for AC in the mid-season and in summer. This feature is highly emphasised by exploiting natural ventilation at night, which allows reducing the building energy demand for cooling by about 30%.The research also indicates that, for Mediterranean climate, the increase in thermal insulation does not always induce positive effects on the thermal performance in summer, and that it might even produce an increase in the heat loads due to the transmission through the envelope.

Building America Case Study: Advanced Extended Plate and Beam Wall System in a Cold-Climate House, Mount Joy, Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

This report presents the design and evaluation of a innovative wall system. This highly insulated (high-R) light-frame wall system for use above grade in residential buildings is referred to as Extended Plate & Beam (EP&B). The EP&B design is the first of its kind to be featured in a new construction test house (NCTH) for the DOE Building America program. The EP&B wall design integrates standard building methods and common building products to construct a high-R wall that minimizes transition risks and costs to builders. The EP&B design combines optimized framing with integrated rigid foam sheathing to increase the wallmore » system's R-value and reduce thermal bridging. The foam sheathing is installed between the wall studs and structural wood sheathing. The exterior wood sheathing is attached directly to a framing extension formed by extended top and bottom plates. The exterior wood sheathing can dry to the exterior and provides bracing, a clear drainage plane and flashing surface for window and door openings, and a nailing surface for siding attachment. With support of the DOE Building America program, Home Innovation Research Labs partnered with Lancaster County Career and Technology Center (LCCTC) to build a NCTH in Lancaster, PA to demonstrate the EP&B wall design in a cold climate (IECC climate zone 5A). The results of the study confirmed the benefits of the systems and the viability of its integration into the house construction process.« less

PDS4 Bundle Creation Governance Using BPMN

NASA Astrophysics Data System (ADS)

Radulescu, C.; Levoe, S. R.; Algermissen, S. S.; Rye, E. D.; Hardman, S. H.

2015-06-01

The AMMOS-PDS Pipeline Service (APPS) provides a Bundle Builder tool, which governs the process of creating, and ultimately generates, PDS4 bundles incrementally, as science products are being generated.

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

Quadrant moved ducts and high efficiency furnace inside conditioned space on nearly all 300 customizable house plans. The builder uses dry, true factory-assembled walls, extensive air sealing, and just in time delivery for pre-sold homes.

Application of real-time database to LAMOST control system

NASA Astrophysics Data System (ADS)

Xu, Lingzhe; Xu, Xinqi

2004-09-01

The QNX based real time database is one of main features for Large sky Area Multi-Object fiber Spectroscopic Telescope's (LAMOST) control system, which serves as a storage and platform for data flow, recording and updating timely various status of moving components in the telescope structure as well as environmental parameters around it. The database joins harmonically in the administration of the Telescope Control System (TCS). The paper presents methodology and technique tips in designing the EMPRESS database GUI software package, such as the dynamic creation of control widgets, dynamic query and share memory. The seamless connection between EMPRESS and the graphical development tool of QNX"s Photon Application Builder (PhAB) has been realized, and so have the Windows look and feel yet under Unix-like operating system. In particular, the real time feature of the database is analyzed that satisfies the needs of the control system.

Lakeland Habitat for Humanity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbride, Theresa L.

2009-03-30

This is a case study of the Lakeland, FLorida, Habitat for Humanity affiliate, which has partnered with DOE's Building America program to homes that achieve energy savings of 30% or more over the Building America baseline home (a home built to the 1993 Model Energy Code). The article includes a description of the energy-efficiency features used. The Lakeland affiliate built several of its homes with ducts in conditioned space, which minimizes heat losses and gains. They also used high-efficiency SEER 14 air conditioners; radiant barriers in the roof to keep attics cooler; above-code high-performance dual-pane vinyl-framed low-emissivity windows; a passivemore » fresh air duct to the air handler; and duct blaster and blower door testing of every home to ensure the home's air tightness. This case study was also prepared as a flier titled "High Performance Builder Spotlight: Lakeland Habitat for Humanity, Lakeland, Florida,: which was cleared as PNNL-SA-59068 and distributed at the International Builders’ Show Feb 13-16, 2008, in Orlando, Florida.« less

Technology Solutions Case Study: Guidance on Taped Insulating Sheathing Drainage Planes

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

The energy efficiency-based financial benefits of adding exterior insulation are well accepted by the building industry, and using exterior insulation as the drainage plane is the next logical step. This case study focuses on the field implementation of taped board insulation as the drainage plane in both new and retrofit residential applications, and provides information and recommendations for insulation contractors, general contractors, builders, remodelers, mechanical contractors, and homeowners. The order of work completed during home construction and retrofit improvements is important. Health and safety issues must be addressed first and are more important than durability issues, and durability issues aremore » more important than saving energy. Three significant items are required to make taped insulating sheathing a simple, long term, and durable drainage plane: first, horizontal joints should be limited or eliminated wherever possible; where a horizontal joint exists, use superior materials; and, frequent installation inspection and regular trade training are required to maintain proper installation.« less

Androgen-induced cerebral venous sinus thrombosis in a young body builder: case report

PubMed Central

Sahraian, Mohammad Ali; Mottamedi, Mahmood; Azimi, Amir Reza; Moghimi, Babak

2004-01-01

Background Cerebral venous sinus thrombosis is an infrequent disease with a variety of causes. Pregnancy, puerperium, contraceptive pills and intracranial infections are the most common causes. The patient may present with headache, focal neurological deficits and seizures. The clinical outcome is highly variable and treatment with heparin is advised. Case presentation The patient is a 22 year old male who presented with headache, repeated vomiting and papilledema. He was a bodybuilder doing exercise since 5 years ago, who had used nandrolone decaonoate 25 milligrams intramuscularly during the previous 5 months. Brain MRI and MRV showed superior sagital and transverse sinus thrombosis and extensive investigations did not reveal any known cause. Conclusions We suggested that androgen was the predisposing factor in our patient. Androgens may increase coagulation factors or platelet activity and cause arterial or venous thrombosis. As athletes may hide using androgens it should be considered as a predisposing factor for thrombotic events in such patients. PMID:15579201

Informatics in radiology: An open-source and open-access cancer biomedical informatics grid annotation and image markup template builder.

PubMed

Mongkolwat, Pattanasak; Channin, David S; Kleper, Vladimir; Rubin, Daniel L

2012-01-01

In a routine clinical environment or clinical trial, a case report form or structured reporting template can be used to quickly generate uniform and consistent reports. Annotation and image markup (AIM), a project supported by the National Cancer Institute's cancer biomedical informatics grid, can be used to collect information for a case report form or structured reporting template. AIM is designed to store, in a single information source, (a) the description of pixel data with use of markups or graphical drawings placed on the image, (b) calculation results (which may or may not be directly related to the markups), and (c) supplemental information. To facilitate the creation of AIM annotations with data entry templates, an AIM template schema and an open-source template creation application were developed to assist clinicians, image researchers, and designers of clinical trials to quickly create a set of data collection items, thereby ultimately making image information more readily accessible.

Informatics in Radiology: An Open-Source and Open-Access Cancer Biomedical Informatics Grid Annotation and Image Markup Template Builder

PubMed Central

Channin, David S.; Rubin, Vladimir Kleper Daniel L.

2012-01-01

In a routine clinical environment or clinical trial, a case report form or structured reporting template can be used to quickly generate uniform and consistent reports. Annotation and Image Markup (AIM), a project supported by the National Cancer Institute’s cancer Biomedical Informatics Grid, can be used to collect information for a case report form or structured reporting template. AIM is designed to store, in a single information source, (a) the description of pixel data with use of markups or graphical drawings placed on the image, (b) calculation results (which may or may not be directly related to the markups), and (c) supplemental information. To facilitate the creation of AIM annotations with data entry templates, an AIM template schema and an open-source template creation application were developed to assist clinicians, image researchers, and designers of clinical trials to quickly create a set of data collection items, thereby ultimately making image information more readily accessible. © RSNA, 2012 PMID:22556315

Airtightness the simple(CS) way

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrews, S.

Builders who might buck against such time consuming air sealing methods as polyethylene wrap and the airtight drywall approach (ADA) may respond better to current strategies. One such method, called SimpleCS, has proven especially effective. SimpleCS, pronounced simplex, stands for simple caulk and seal. A modification of the ADA, SimpleCS is an air-sealing management tool, a simplified systems approach to building tight homes. The system address the crucial question of when and by whom various air sealing steps should be done. It avoids the problems that often occur when later contractors cut open polyethylene wrap to drill holes in themore » drywall. The author describes how SimpleCS works, and the cost and training involved.« less

Scalable cluster administration - Chiba City I approach and lessons learned.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Navarro, J. P.; Evard, R.; Nurmi, D.

2002-07-01

Systems administrators of large clusters often need to perform the same administrative activity hundreds or thousands of times. Often such activities are time-consuming, especially the tasks of installing and maintaining software. By combining network services such as DHCP, TFTP, FTP, HTTP, and NFS with remote hardware control, cluster administrators can automate all administrative tasks. Scalable cluster administration addresses the following challenge: What systems design techniques can cluster builders use to automate cluster administration on very large clusters? We describe the approach used in the Mathematics and Computer Science Division of Argonne National Laboratory on Chiba City I, a 314-node Linuxmore » cluster; and we analyze the scalability, flexibility, and reliability benefits and limitations from that approach.« less

GUIs in the MIDAS environment

NASA Technical Reports Server (NTRS)

Ballester, P.

1992-01-01

MIDAS (Munich Image Data Analysis System) is the image processing system developed at ESO for astronomical data reduction. MIDAS is used for off-line data reduction at ESO and many astronomical institutes all over Europe. In addition to a set of general commands, enabling to process and analyze images, catalogs, graphics and tables, MIDAS includes specialized packages dedicated to astronomical applications or to specific ESO instruments. Several graphical interfaces are available in the MIDAS environment: XHelp provides an interactive help facility, and XLong and XEchelle enable data reduction of long-slip and echelle spectra. GUI builders facilitate the development of interfaces. All ESO interfaces comply to the ESO User Interfaces Common Conventions which secures an identical look and feel for telescope operations, data analysis, and archives.

Involvement of Individuals in the Development of Technical Solutions and Rules of Management for Building Renovation Projects: A Case Study of Latvia

NASA Astrophysics Data System (ADS)

Pukite, I.; Grekis, A.; Geipele, I.; Zeltins, N.

2017-08-01

In March 2016, the Latvian government approved a new support program for increasing energy efficiency in residential apartment buildings. For the support of renovation of apartment buildings in the period from 2016 to 2023, 166 470 588 EUR will be available. Different persons, such as energy auditors, designers, architects, project managers and builders, will be involved in the process of planning, development and implementation of building renovation. At the development stage of the building renovation project, special attention should be devoted to the first stage - energy audit and technical project development. The problem arises due to the fact that each of these individuals, during the development of technical building documentation, does not work as a completely unified system. The implementation of construction project planning and organisational management system is one of the most important factors to guarantee that the quality of building renovation project is ensured in accordance with the laws and regulatory standards. The paper studies mutual cooperation, professionalism and the role of information feedback of personnel involved in the planning stage of building renovation, which is an essential prerequisite for the renovation process in order to achieve high quality of work and reduce the energy performance indicator. The present research includes the analysis of different technical solutions and their impact on energy efficiency. Mutual harmonisation of technical specifications is also investigated.

Between the Under-Labourer and the Master-Builder: Observations on Bunge's Method

NASA Astrophysics Data System (ADS)

Agassi, Joseph

2012-10-01

Mario Bunge has repeatedly discussed contributions to philosophy and to science that are worthless at best and dangerous at worst, especially cases of pseudo-science. He clearly gives his reason in his latest essay on this matter: "The fact that science can be faked to the point of deceiving science lovers suggests the need for a rigorous sifting device". Moreover, this sifting has its rewards, as "sometimes intellectual gold comes mixed with muck". Furthermore, the sifting device is a demarcation of science, which answers interesting questions: what is valuable in science and what makes it tick? The question is under dispute. So before coming to it we should admit a few preliminary ideas that are more difficult to contest than ideas that purport to demarcate science.

The Birth of Lepton Colliders in Italy and the United States

NASA Astrophysics Data System (ADS)

Paris, Elizabeth

2003-04-01

In 1960 the highest center-of-mass energies in particle physics were being achieved via proton synchrotrons utilizing stationary targets. However, efforts were already underway to challenge this hegemony. In addition to Soviet work in Novosibirsk, groups at Stanford University in California and at the Frascati National Laboratories near Rome each had begun original investigation towards one particular type of challenger: colliding beam storage rings. For the group in California, the accomplishment involved creating the potential for feasible experiments. The energetic advantages of the colliding beam configuration had long been accepted - together with its impossibility for realization. The builders of the Princeton-Stanford machine feel that creating usable beams and a reasonable reaction rate is what stood between this concept and its glorious future. For the European builders of AdA, however, the beauty emerges from recognizing the enormous potential inherent in electron-positron annihilations. At least as important for the rise of electron-positron colliders, though, is the role of both of these projects as cultural firsts -- as places where particular sets of physicists got their feet wet associating with beams and beam problems and with the many individuals who were addressing beam problems. The Princeton-Stanford Collider provided experience which its builders would use to move on, functioning as both a technological and political platform for creating what would eventually become SPEAR. For the Roman group, the pursuit of AdA encouraged investigation which applied equally well to their next machine, Adone.

14 CFR 65.101 - Eligibility requirements: General.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Administrator and is specifically designed to qualify the applicant for the job on which the applicant is to be...) This section does not apply to the issuance of a repairman certificate (experimental aircraft builder...

14 CFR 65.101 - Eligibility requirements: General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Administrator and is specifically designed to qualify the applicant for the job on which the applicant is to be...) This section does not apply to the issuance of a repairman certificate (experimental aircraft builder...

14 CFR 65.101 - Eligibility requirements: General.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Administrator and is specifically designed to qualify the applicant for the job on which the applicant is to be...) This section does not apply to the issuance of a repairman certificate (experimental aircraft builder...

Production-Built Homes: The Cost Advantages of Smart Growth

EPA Pesticide Factsheets

This study identifies the components and techniques of home building in traditional versus conventional developments, and attempts to help production builders better understand the cost differences between the two types of developments.

Accessorizing Building Science – A Web Platform to Support Multiple Market Transformation Programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madison, Michael C.; Antonopoulos, Chrissi A.; Dowson, Scott T.

As demand for improved energy efficiency in homes increases, builders need information on the latest findings in building science, rapidly ramping-up energy codes, and technical requirements for labeling programs. The Building America Solution Center is a Department of Energy (DOE) website containing hundreds of expert guides designed to help residential builders install efficiency measures in new and existing homes. Builders can package measures with other media for customized content. Website content provides technical support to market transformation programs such as ENERGY STAR and has been cloned and adapted to provide content for the Better Buildings Residential Program. The Solution Centermore » uses the Drupal open source content management platform to combine a variety of media in an interactive manner to make information easily accessible. Developers designed a unique taxonomy to organize and manage content. That taxonomy was translated into web-based modules that allow users to rapidly traverse structured content with related topics, and media. We will present information on the current design of the Solution Center and the underlying technology used to manage the content. The paper will explore development of features, such as “Field Kits” that allow users to bundle and save content for quick access, along with the ability to export PDF versions of content. Finally, we will discuss development of an Android based mobile application, and a visualization tool for interacting with Building Science Publications that allows the user to dynamically search the entire Building America Library.« less

Landscape Water Budget Tool

EPA Pesticide Factsheets

WaterSense created the Water Budget Tool as one option to help builders, landscape professionals, and irrigation professionals certified by a WaterSense labeled program meet the criteria specified in the WaterSense New Home Specification.

Water Budget Quick Start Guide

EPA Pesticide Factsheets

WaterSense created the Water Budget Tool as one option to help builders, landscape professionals, and irrigation professionals certified by a WaterSense labeled program meet the criteria specified in the WaterSense New Home Specification.

Bridge inspector's manual for movable bridges.

DOT National Transportation Integrated Search

1977-01-01

Importance of Inspection-Movable bridges are built to the rigid specifications : of such groups as the American Association of State Highway and : Transportation Officials (AASHTO), the American Road Builders Association : (ARBA) and Underwriters Lab...

24 CFR 203.12 - Mortgage insurance on proposed or new construction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... conditions (i.e., rock formations, unstable soils or slopes, high ground water levels, inadequate surface... of the improvements. The Builder's Certification must be provided to the appraiser for reference...

24 CFR 203.12 - Mortgage insurance on proposed or new construction.

Code of Federal Regulations, 2010 CFR

2010-04-01

... conditions (i.e., rock formations, unstable soils or slopes, high ground water levels, inadequate surface... of the improvements. The Builder's Certification must be provided to the appraiser for reference...

24 CFR 242.41 - Certification of cost requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... shall enter into an agreement in form and content satisfactory to HUD for the purpose of precluding any... disclose its relationship with the builder, including any collateral agreement, and shall agree: (a) To...

24 CFR 242.41 - Certification of cost requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... shall enter into an agreement in form and content satisfactory to HUD for the purpose of precluding any... disclose its relationship with the builder, including any collateral agreement, and shall agree: (a) To...

24 CFR 242.41 - Certification of cost requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... shall enter into an agreement in form and content satisfactory to HUD for the purpose of precluding any... disclose its relationship with the builder, including any collateral agreement, and shall agree: (a) To...

24 CFR 242.41 - Certification of cost requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... shall enter into an agreement in form and content satisfactory to HUD for the purpose of precluding any... disclose its relationship with the builder, including any collateral agreement, and shall agree: (a) To...

24 CFR 242.41 - Certification of cost requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... shall enter into an agreement in form and content satisfactory to HUD for the purpose of precluding any... disclose its relationship with the builder, including any collateral agreement, and shall agree: (a) To...

Public Notice 2017-25: Accurate Builders & Developers

EPA Pesticide Factsheets

EPA is providing notice of a proposed administrative penalty assessment for alleged violations of the Clean Water Act (Act). EPA is also providing notice of opportunity to comment on the proposed penalty assessment.

Energy research: accelerator builders eager to aid fusion work.

PubMed

Metz, W D

1976-10-15

Useful fusion energy may be generated by means of heavy ion accelerator driven implosions if the contraints dictated by the physics and economics of thermonuclear targets and reactors can be satisfied.

Advantages of Brahms for Specifying and Implementing a Multiagent Human-Robotic Exploration System

NASA Technical Reports Server (NTRS)

Clancey, William J.; Sierhuis, Maarten; Kaskiris, Charis; vanHoof, Ron

2003-01-01

We have developed a model-based, distributed architecture that integrates diverse components in a system designed for lunar and planetary surface operations: an astronaut's space suit, cameras, all-terrain vehicles, robotic assistant, crew in a local habitat, and mission support team. Software processes ('agents') implemented in the Brahms language, run on multiple, mobile platforms. These mobile agents interpret and transform available data to help people and robotic systems coordinate their actions to make operations more safe and efficient. The Brahms-based mobile agent architecture (MAA) uses a novel combination of agent types so the software agents may understand and facilitate communications between people and between system components. A state-of-the-art spoken dialogue interface is integrated with Brahms models, supporting a speech-driven field observation record and rover command system. An important aspect of the methodology involves first simulating the entire system in Brahms, then configuring the agents into a runtime system Thus, Brahms provides a language, engine, and system builder's toolkit for specifying and implementing multiagent systems.

Measure Guideline. Transitioning to a Tankless Water Heater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brozyna, K.; Rapport, A.

2012-09-01

This measure guideline provides information to help residential builders and retrofitters with the design, specification, selection, implementation, installation, and maintenance issues of transitioning from tank-type water heaters to tankless water heaters.

SRTM Stereo Pair with Landsat Overlay: Los Angeles to San Joaquin Valley, California

NASA Image and Video Library

2000-09-21

California topography poses challenges for road builders. Northwest of Los Angeles, deformation of Earth crust along the Pacific-North American crustal plate boundary has made transportation difficult.

Technical Solutions to Common Indoor Air Quality Issues in Schools

EPA Pesticide Factsheets

Indoor Air Quality (IAQ) Design Tools for Schools provides voluntary guidance for school personnel, architects, engineers, builders and contractors, parents, and the community on key school construction and renovation issues.

New Whole-House Solutions Case Study: Challenges of Achieving 2012 IECC Air Sealing Requirements in Multifamily Dwellings, Upstate New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2014-11-01

While previous versions of the International Energy Conservation Code (IECC) have included provisions to improve the air tightness of dwellings, for the first time, the 2012 IECC mandates compliance verification through blower door testing. Simply completing the Air Barrier and Insulation Installation checklist through visual inspection is no longer sufficient; the 2012 IECC mandates a significantly stricter air sealing requirement. In Climate Zones 3 through 8, air leakage may not exceed 3 ACH50, which is a significant reduction from the 2009 IECC requirement of 7 ACH50. This requirement is for all residential buildings, which includes low-rise multifamily dwellings. While thismore » air leakage rate requirement is an important component to achieving an efficient building thermal envelope, currently, the code language doesn't explicitly address differences between single family and multifamily applications. In addition, the 2012 IECC does not provide an option to sample dwellings for larger multifamily buildings, so compliance would have to be verified on every unit. With compliance with the 2012 IECC air leakage requirements on the horizon, several of Building America team Consortium for Advanced Residential Building's (CARB) multifamily builder partners are evaluating how best to comply with this requirement. Builders are not sure whether it is more practical or beneficial to simply pay for guarded testing or to revise their air sealing strategies to improve compartmentalization to comply with code requirements based on unguarded blower door testing. This report summarizes CARB's research that was conducted to assess the feasibility of meeting the 2012 IECC air leakage requirements in three multifamily buildings.« less

Question Builder: Be Prepared for Your Next Medical Appointment

MedlinePlus

... Scientific Peer Review Award Process Post-Award Grant Management AHRQ Grantee Profiles Getting Recognition for Your AHRQ-Funded Study Contracts Project Research Online Database (PROD) Searchable database of AHRQ ...

A data distribution strategy for the 1990s (files are not enough)

NASA Technical Reports Server (NTRS)

Tankenson, Mike; Wright, Steven

1993-01-01

Virtually all of the data distribution strategies being contemplated for the EOSDIS era revolve around the use of files. Most, if not all, mass storage technologies are based around the file model. However, files may be the wrong primary abstraction for supporting scientific users in the 1990s and beyond. Other abstractions more closely matching the respective scientific discipline of the end user may be more appropriate. JPL has built a unique multimission data distribution system based on a strategy of telemetry stream emulation to match the responsibilities of spacecraft team and ground data system operators supporting our nations suite of planetary probes. The current system, operational since 1989 and the launch of the Magellan spacecraft, is supporting over 200 users at 15 remote sites. This stream-oriented data distribution model can provide important lessons learned to builders of future data systems.

Tunneling : the State of the Industry

DOT National Transportation Integrated Search

1976-05-01

Tunneling is examined as an industry. The demand for its services, the makeup of the industry, some history and its problems and prospects, are analyzed. Industry participants are listed: owners, engineer firms, tunnel builders and specialized suppli...

Local Efforts to Reduce Radon Risks - Highlights and Lessons Learned

EPA Pesticide Factsheets

In these stories, you will read about people who educated their families, neighbors, colleagues,and communities, and challenged local builders, governments, code enforcement officials, and others to protect the public from indoor radon.

38 CFR 36.4347 - Lender Appraisal Processing Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

...., to the appraisal report must be made in a contrasting color, be clearly legible, and signed and dated... with a real estate firm builder, land developer or escrow agent as a subsidiary division, investment or...

America's foremost early astronomer. [David Rittenhouse

NASA Technical Reports Server (NTRS)

Rubincam, David Parry; Rubincam, Milton, II

1995-01-01

The life of 18th century astronomer, craftsman, and partriot David Rittenhouse is detailed. As a craftsman, he distinguished himself as one of the foremost builders of clocks. He also built magnetic compasses and surveying instruments. The finest examples of his craftsmanship are considered two orreries, mechanical solar systems. In terms of astronomical observations, his best-known contribution was his observation of the transit of Venus in 1769. Rittenhouse constructed the first diffraction grating. Working as Treasurer of Pennsylvania throughout the Revolution, he became the first director of the Mint in 1792. Astronomical observations in later life included charting the position of Uranus after its discovery.

17. DETAIL OF SOUTH PORTAL, SHOWING "TREE OF LIFE" RAILING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. DETAIL OF SOUTH PORTAL, SHOWING "TREE OF LIFE" RAILING DETAIL AS WELL AS BUILDER'S PLATE. - Falls Bridge, Spanning Schuylkill River, connecting East & West River Drives, Philadelphia, Philadelphia County, PA

Sustainable Management of Construction and Demolition Materials

EPA Pesticide Factsheets

This web page discusses how to sustainably manage construction and demolition materials, Information covers, what they are, and how builders, construction crews, demolition teams,and deign practitioners can divert C&D from landfills.