Small Stirling dynamic isotope power system for robotic space missions

NASA Technical Reports Server (NTRS)

Bents, D. J.

1992-01-01

The design of a multihundred-watt Dynamic Isotope Power System (DIPS), based on the U.S. Department of Energy (DOE) General Purpose Heat Source (GPHS) and small (multihundred-watt) free-piston Stirling engine (FPSE), is being pursued as a potential lower cost alternative to radioisotope thermoelectric generators (RTG's). The design is targeted at the power needs of future unmanned deep space and planetary surface exploration missions ranging from scientific probes to Space Exploration Initiative precursor missions. Power level for these missions is less than a kilowatt. The incentive for any dynamic system is that it can save fuel and reduce costs and radiological hazard. Unlike DIPS based on turbomachinery conversion (e.g. Brayton), this small Stirling DIPS can be advantageously scaled to multihundred-watt unit size while preserving size and mass competitiveness with RTG's. Stirling conversion extends the competitive range for dynamic systems down to a few hundred watts--a power level not previously considered for dynamic systems. The challenge for Stirling conversion will be to demonstrate reliability and life similar to RTG experience. Since the competitive potential of FPSE as an isotope converter was first identified, work has focused on feasibility of directly integrating GPHS with the Stirling heater head. Thermal modeling of various radiatively coupled heat source/heater head geometries has been performed using data furnished by the developers of FPSE and GPHS. The analysis indicates that, for the 1050 K heater head configurations considered, GPHS fuel clad temperatures remain within acceptable operating limits. Based on these results, preliminary characterizations of multihundred-watt units have been established.

CNT coated thread micro-electro-mechanical system for finger proprioception sensing

NASA Astrophysics Data System (ADS)

Shafi, A. A.; Wicaksono, D. H. B.

2017-04-01

In this paper, we aim to fabricate cotton thread based sensor for proprioceptive application. Cotton threads are utilized as the structural component of flexible sensors. The thread is coated with multi-walled carbon nanotube (MWCNT) dispersion by using facile conventional dipping-drying method. The electrical characterization of the coated thread found that the resistance per meter of the coated thread decreased with increasing the number of dipping. The CNT coated thread sensor works based on piezoresistive theory in which the resistance of the coated thread changes when force is applied. This thread sensor is sewed on glove at the index finger between middle and proximal phalanx parts and the resistance change is measured upon grasping mechanism. The thread based microelectromechanical system (MEMS) enables the flexible sensor to easily fit perfectly on the finger joint and gives reliable response as proprioceptive sensing.

Interphalangeal Osteoarthritis Radiographic Simplified (iOARS) score: a radiographic method to detect osteoarthritis of the interphalangeal finger joints based on its histopathological alterations.

PubMed

Sunk, Ilse-Gerlinde; Amoyo-Minar, Love; Stamm, Tanja; Haider, Stefanie; Niederreiter, Birgit; Supp, Gabriela; Soleiman, Afschin; Kainberger, Franz; Smolen, Josef S; Bobacz, Klaus

2014-11-01

To develop a radiographic score for assessment of hand osteoarthritis (OA) that is based on histopathological alterations of the distal (DIP) and proximal (PIP) interphalangeal joints. DIP and PIP joints were obtained from corpses (n=40). Plain radiographies of these joints were taken. Joint samples were prepared for histological analysis; cartilage damage was graded according to the Mankin scoring system. A 2×2 Fisher's exact test was applied to define those radiographic features most likely to be associated with histological alterations. Receiver operating characteristic curves were analysed to determine radiographic thresholds. Intraclass correlation coefficients (ICC) estimated intra- and inter-reader variability. Spearman's correlation was applied to examine the relationship between our score and histopathological changes. Differences between groups were determined by a Student's t test. The Interphalangeal Osteoarthritis Radiographic Simplified (iOARS) score is presented. The score is based on histopathological changes of DIP and PIP joints and follows a simple dichotomy whether OA is present or not. The iOARS score relies on three equally ranked radiographic features (osteophytes, joint space narrowing and subchondral sclerosis). For both DIP and PIP joints, the presence of one x-ray features reflects interphalangeal OA. Sensitivity and specificity for DIP joints were 92.3% and 90.9%, respectively, and 75% and 100% for PIP joints. All readers were able to reproduce their own readings in DIP and PIP joints after 4 weeks. The overall agreement between the three readers was good; ICCs ranged from 0.945 to 0.586. Additionally, outcomes of the iOARS score in a hand OA cohort revealed a higher prevalence of interphalangeal joint OA compared with the Kellgren and Lawrence score. The iOARS score is uniquely based on histopathological alterations of the interphalangeal joints in order to reliably determine OA of the DIP and PIP joints radiographically. Its high specificity and sensitivity together with the dichotomous approach renders the iOARS score reliable, fast to perform and easy to apply. This tool may not only be valuable in daily clinical practice but also in clinical and epidemiological trials. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The infection and impact of Azorhizobium caulinodans ORS571 on wheat (Triticum aestivum L.).

PubMed

Liu, Huawei; Wang, Xiaojing; Qi, Huaiting; Wang, Qian; Chen, Yongchao; Li, Qiang; Zhang, Yuying; Qiu, Li; Fontana, Julia Elise; Zhang, Baohong; Wang, Weiling; Xie, Yingge

2017-01-01

Based on our previous study, cereal crop wheat (Triticum aestivum L.) could be infected by rhizobia Azorhizobium caulinodans ORS571, and form para-nodules with the induction of 2.4-dichlorophenoxyacetic acid, a common plant growth regulator. To enhance this infection and the potential agricultural application, we compared six different infection methods (Direct seed dip; Seed germination dip; Pruned-root dip; Foliar spray; Circum-soil dip; Seed dip and circum-soil dip) for achieving the high efficient infection of A. caulinodans into wheat plants by employing a green fluorescent protein (gfp)-labeled Azorhizobium caulinodans strain ORS571. With proper methods, copious rhizobia could enter the interior and promote the growth of wheat to the hilt. Circum-soil dip was proved to be the most efficient method, seed germination dip and pruned-root dip is the last recommended to infect wheat, seed germination dip and seed dip and circum-soil dip showed better effects on plant growth, pruned-root dip did not show too much effect on plant growth. This study laid the foundation for understanding the interaction between rhizobia and cereal crops and the growth-promoting function of rhizobia.

A Web application for the management of clinical workflow in image-guided and adaptive proton therapy for prostate cancer treatments.

PubMed

Yeung, Daniel; Boes, Peter; Ho, Meng Wei; Li, Zuofeng

2015-05-08

Image-guided radiotherapy (IGRT), based on radiopaque markers placed in the prostate gland, was used for proton therapy of prostate patients. Orthogonal X-rays and the IBA Digital Image Positioning System (DIPS) were used for setup correction prior to treatment and were repeated after treatment delivery. Following a rationale for margin estimates similar to that of van Herk,(1) the daily post-treatment DIPS data were analyzed to determine if an adaptive radiotherapy plan was necessary. A Web application using ASP.NET MVC5, Entity Framework, and an SQL database was designed to automate this process. The designed features included state-of-the-art Web technologies, a domain model closely matching the workflow, a database-supporting concurrency and data mining, access to the DIPS database, secured user access and roles management, and graphing and analysis tools. The Model-View-Controller (MVC) paradigm allowed clean domain logic, unit testing, and extensibility. Client-side technologies, such as jQuery, jQuery Plug-ins, and Ajax, were adopted to achieve a rich user environment and fast response. Data models included patients, staff, treatment fields and records, correction vectors, DIPS images, and association logics. Data entry, analysis, workflow logics, and notifications were implemented. The system effectively modeled the clinical workflow and IGRT process.

System for analysis of explosives

DOEpatents

Haas, Jeffrey S [San Ramon, CA

2010-06-29

A system for analysis of explosives. Samples are spotted on a thin layer chromatography plate. Multi-component explosives standards are spotted on the thin layer chromatography plate. The thin layer chromatography plate is dipped in a solvent mixture and chromatography is allowed to proceed. The thin layer chromatography plate is dipped in reagent 1. The thin layer chromatography plate is heated. The thin layer chromatography plate is dipped in reagent 2.

3D Model of the San Emidio Geothermal Area

DOE Data Explorer

James E. Faulds

2013-12-31

The San Emidio geothermal system is characterized by a left-step in a west-dipping normal fault system that bounds the western side of the Lake Range. The 3D geologic model consists of 5 geologic units and 55 faults. Overlying Jurrassic-Triassic metasedimentary basement is a ~500 m-1000 m thick section of the Miocene lower Pyramid sequence, pre- syn-extensional Quaternary sedimentary rocks and post-extensional Quaternary rocks. 15-30º eastward dip of the stratigraphy is controlled by the predominant west-dipping fault set. Both geothermal production and injection are concentrated north of the step over in an area of closely spaced west dipping normal faults.

Directly imaging steeply-dipping fault zones in geothermal fields with multicomponent seismic data

DOE PAGES

Chen, Ting; Huang, Lianjie

2015-07-30

For characterizing geothermal systems, it is important to have clear images of steeply-dipping fault zones because they may confine the boundaries of geothermal reservoirs and influence hydrothermal flow. Elastic reverse-time migration (ERTM) is the most promising tool for subsurface imaging with multicomponent seismic data. However, conventional ERTM usually generates significant artifacts caused by the cross correlation of undesired wavefields and the polarity reversal of shear waves. In addition, it is difficult for conventional ERTM to directly image steeply-dipping fault zones. We develop a new ERTM imaging method in this paper to reduce these artifacts and directly image steeply-dipping fault zones.more » In our new ERTM method, forward-propagated source wavefields and backward-propagated receiver wavefields are decomposed into compressional (P) and shear (S) components. Furthermore, each component of these wavefields is separated into left- and right-going, or downgoing and upgoing waves. The cross correlation imaging condition is applied to the separated wavefields along opposite propagation directions. For converted waves (P-to-S or S-to-P), the polarity correction is applied to the separated wavefields based on the analysis of Poynting vectors. Numerical imaging examples of synthetic seismic data demonstrate that our new ERTM method produces high-resolution images of steeply-dipping fault zones.« less

Using the charge-stabilization technique in the double ionization potential equation-of-motion calculations with dianion references.

PubMed

Kuś, Tomasz; Krylov, Anna I

2011-08-28

The charge-stabilization method is applied to double ionization potential equation-of-motion (EOM-DIP) calculations to stabilize unstable dianion reference functions. The auto-ionizing character of the dianionic reference states spoils the numeric performance of EOM-DIP limiting applications of this method. We demonstrate that reliable excitation energies can be computed by EOM-DIP using a stabilized resonance wave function instead of the lowest energy solution corresponding to the neutral + free electron(s) state of the system. The details of charge-stabilization procedure are discussed and illustrated by examples. The choice of optimal stabilizing Coulomb potential, which is strong enough to stabilize the dianion reference, yet, minimally perturbs the target states of the neutral, is the crux of the approach. Two algorithms of choosing optimal parameters of the stabilization potential are presented. One is based on the orbital energies, and another--on the basis set dependence of the total Hartree-Fock energy of the reference. Our benchmark calculations of the singlet-triplet energy gaps in several diradicals show a remarkable improvement of the EOM-DIP accuracy in problematic cases. Overall, the excitation energies in diradicals computed using the stabilized EOM-DIP are within 0.2 eV from the reference EOM spin-flip values. © 2011 American Institute of Physics

Nonhazardous Chemical Treatments and Smart Monitoring and Control System for Heating and Cooling Systems

DTIC Science & Technology

2007-06-01

box with the dip slides provides application instructions and illustrates acceptable bacteria levels. Both dip slide and Biotrace ATP Luminometer...Control Good Control Poor Control Biotrace ATP Planktonic 100 to 300 RLU 300 to 1000 RLU >1000 RLU Dip Tube Anaerobic Bacteria 0 organism/mL ɝ...completed monthly to record biocide levels and bacteria tests. Another biocide test method, the Biotrace ATP Luminometer, measures planktonic

75 FR 68394 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-05

... Woven and Knit impregnated with Flat Dipped Rubber/Plastic Gloves. SUMMARY: The U. S. Small Business... Flat Dipped Rubber/Plastic Gloves, under North American Industry Classification System (NAICS) code... Rule for Woven and Knit impregnated with Flat Dipped Rubber/Plastic Gloves under PSC 9999...

Tunnel Design by Rock Mass Classifications

DTIC Science & Technology

1990-01-01

exhibited a slaking-like action when submerged . This is attributed to stress re- lief by coring. Bedding strikes roughly north-south and generally dips...dure ic diagrammatically depicted in Figure D5. This system, knorn as the Modified Basic RMR system or MBR in short, is based on experience gained in an

Multiple-Satellite Observation of Magnetic Dip Event During the Substorm on 10 October 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

He, Zhaoguo; Chen, Lunjin; Zhu, Hui

Here, we present a multiple-satellite observation of the magnetic dip event during the substorm on 10 October 2013. The observation illustrates the temporal and spatial evolution of the magnetic dip and gives a compelling evidence that ring current ions induce the magnetic dip by enhanced plasma beta. The dip moves with the energetic ions in a comparable drift velocity and affects the dynamics of relativistic electrons in the radiation belt. In addition, the magnetic dip provides a favorable condition for the electromagnetic ion cyclotron (EMIC) wave generation based on the linear theory analysis. The calculated proton diffusion coefficients show thatmore » the observed EMIC wave can lead to the pitch angle scattering losses of the ring current ions, which in turn partially relax the magnetic dip in the observations. This study enriches our understanding of magnetic dip evolution and demonstrates the important role of the magnetic dip for the coupling of radiation belt and ring current.« less

Multiple-Satellite Observation of Magnetic Dip Event During the Substorm on 10 October 2013

NASA Astrophysics Data System (ADS)

He, Zhaoguo; Chen, Lunjin; Zhu, Hui; Xia, Zhiyang; Reeves, G. D.; Xiong, Ying; Xie, Lun; Cao, Yong

2017-09-01

We present a multiple-satellite observation of the magnetic dip event during the substorm on 10 October 2013. The observation illustrates the temporal and spatial evolution of the magnetic dip and gives a compelling evidence that ring current ions induce the magnetic dip by enhanced plasma beta. The dip moves with the energetic ions in a comparable drift velocity and affects the dynamics of relativistic electrons in the radiation belt. In addition, the magnetic dip provides a favorable condition for the electromagnetic ion cyclotron (EMIC) wave generation based on the linear theory analysis. The calculated proton diffusion coefficients show that the observed EMIC wave can lead to the pitch angle scattering losses of the ring current ions, which in turn partially relax the magnetic dip in the observations. This study enriches our understanding of magnetic dip evolution and demonstrates the important role of the magnetic dip for the coupling of radiation belt and ring current.

Multiple-Satellite Observation of Magnetic Dip Event During the Substorm on 10 October 2013

DOE PAGES

He, Zhaoguo; Chen, Lunjin; Zhu, Hui; ...

2017-09-05

Here, we present a multiple-satellite observation of the magnetic dip event during the substorm on 10 October 2013. The observation illustrates the temporal and spatial evolution of the magnetic dip and gives a compelling evidence that ring current ions induce the magnetic dip by enhanced plasma beta. The dip moves with the energetic ions in a comparable drift velocity and affects the dynamics of relativistic electrons in the radiation belt. In addition, the magnetic dip provides a favorable condition for the electromagnetic ion cyclotron (EMIC) wave generation based on the linear theory analysis. The calculated proton diffusion coefficients show thatmore » the observed EMIC wave can lead to the pitch angle scattering losses of the ring current ions, which in turn partially relax the magnetic dip in the observations. This study enriches our understanding of magnetic dip evolution and demonstrates the important role of the magnetic dip for the coupling of radiation belt and ring current.« less

Peak-dip-hump lineshape from holographic superconductivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, J.-W.; Kao, Y.-J.; Wen, W.-Y.

2010-07-15

We study the fermionic spectral function in a holographic superconductor model. At zero temperature, there is no horizon and hence the entropy of the system is zero after the backreaction of the condensate is taken into account. We find the system exhibits the famous peak-dip-hump lineshape with a sharp low-energy peak followed by a dip and then a hump at higher energies. This feature is widely observed in the spectrum of several high-T{sub c} superconductors.

Tunable high-channel-count bandstop graphene plasmonic filters based on plasmon induced transparency

NASA Astrophysics Data System (ADS)

Zhang, Zhengren; Long, Yang; Ma, Pengyu; Li, Hongqiang

2017-11-01

A high-channel-count bandstop graphene plasmonic filter based on ultracompact plasmonic structure is proposed in this paper. It consists of graphene waveguide side-coupled with a series of graphene filtering units. The study shows that the waveguide-resonator system performs a multiple plasmon induced transparency (PIT) phenomenon. By carefully adjusting the Fermi level of the filtering units, any two adjacent transmitted dips which belong to different PIT units can produce coherent coupling superposition enhancement. This property prevents the attenuation of the high-frequency transmission dips of multiple PIT and leads to an excellent bandstop filter with multiple channels. Specifically, the bandwidth and modulation depth of the filters can be flexibly adjusted by tuning the Fermi energy of the graphene waveguide. This ultracompact plasmonic structure contributes to the achievement of frequency division multiplexing systems for optical computing and communications in highly integrated optical circuits.

A Web application for the management of clinical workflow in image‐guided and adaptive proton therapy for prostate cancer treatments

PubMed Central

Boes, Peter; Ho, Meng Wei; Li, Zuofeng

2015-01-01

Image‐guided radiotherapy (IGRT), based on radiopaque markers placed in the prostate gland, was used for proton therapy of prostate patients. Orthogonal X‐rays and the IBA Digital Image Positioning System (DIPS) were used for setup correction prior to treatment and were repeated after treatment delivery. Following a rationale for margin estimates similar to that of van Herk,(1) the daily post‐treatment DIPS data were analyzed to determine if an adaptive radiotherapy plan was necessary. A Web application using ASP.NET MVC5, Entity Framework, and an SQL database was designed to automate this process. The designed features included state‐of‐the‐art Web technologies, a domain model closely matching the workflow, a database‐supporting concurrency and data mining, access to the DIPS database, secured user access and roles management, and graphing and analysis tools. The Model‐View‐Controller (MVC) paradigm allowed clean domain logic, unit testing, and extensibility. Client‐side technologies, such as jQuery, jQuery Plug‐ins, and Ajax, were adopted to achieve a rich user environment and fast response. Data models included patients, staff, treatment fields and records, correction vectors, DIPS images, and association logics. Data entry, analysis, workflow logics, and notifications were implemented. The system effectively modeled the clinical workflow and IGRT process. PACS number: 87 PMID:26103504

Laramide structure of the central Sangre de Cristo Mountains and adjacent Raton Basin, southern Colorado

USGS Publications Warehouse

Lindsey, D.A.

1998-01-01

Laramide structure of the central Sangre de Cristo Mountains (Culebra Range) is interpreted as a system of west-dipping, basement-involved thrusts and reverse faults. The Culebra thrust is the dominant structure in the central part of the range; it dips 30 -55?? west and brings Precambrian metamorphic base-ment rocks over unmetamorphosed Paleozoic rocks. East of the Culebra thrust, thrusts and reverse faults break the basement and overlying cover rocks into north-trending fault blocks; these boundary faults probably dip 40-60?? westward. The orientation of fault slickensides indicates oblique (northeast) slip on the Culebra thrust and dip-slip (ranging from eastward to northward) movement on adjacent faults. In sedimentary cover rocks, east-vergent anticlines overlie and merge with thrusts and reverse faults; these anticlines are interpreted as fault-propagation folds. Minor east-dipping thrusts and reverse faults (backthrusts) occur in both the hanging walls and footwalls of thrusts. The easternmost faults and folds of the Culebra Range form a continuous structural boundary between the Laramide Sangre de Cristo highland and the Raton Basin. Boundary structures consist of west-dipping frontal thrusts flanked on the basinward side by poorly exposed, east-dipping backthrusts. The backthrusts are interpreted to overlie structural wedges that have been emplaced above blind thrusts in the basin margin. West-dipping frontal thrusts and blind thrusts are interpreted to involve basement, but backthrusts are rooted in basin-margin cover rocks. At shallow structural levels where erosion has not exposed a frontal thrust, the structural boundary of the basin is represented by an anticline or monocline. Based on both regional and local stratigraphic evidence, Laramide deformation in the Culebra Range and accompanying synorogenic sedimentation in the western Raton Basin probably took place from latest Cretaceous through early Eocene time. The earliest evidence of uplift and erosion of a highland is the appearance of abundant feldspar in the Late Cretaceous Vermejo Formation. Above the Vermejo, unconformities overlain by conglomerate indicate continued thrusting and erosion of highlands from late Cretaceous (Raton) through Eocene (Cuchara) time. Eocene alluvial-fan conglomerates in the Cuchara Formation may represent erosion of the Culebra thrust block. Deposition in the Raton Basin probably shifted north from New Mexico to southern Colorado from Paleocene to Eocene time as movement on individual thrusts depressed adjacent segments of the basin.

A Bayesian deconvolution strategy for immunoprecipitation-based DNA methylome analysis

PubMed Central

Down, Thomas A.; Rakyan, Vardhman K.; Turner, Daniel J.; Flicek, Paul; Li, Heng; Kulesha, Eugene; Gräf, Stefan; Johnson, Nathan; Herrero, Javier; Tomazou, Eleni M.; Thorne, Natalie P.; Bäckdahl, Liselotte; Herberth, Marlis; Howe, Kevin L.; Jackson, David K.; Miretti, Marcos M.; Marioni, John C.; Birney, Ewan; Hubbard, Tim J. P.; Durbin, Richard; Tavaré, Simon; Beck, Stephan

2009-01-01

DNA methylation is an indispensible epigenetic modification of mammalian genomes. Consequently there is great interest in strategies for genome-wide/whole-genome DNA methylation analysis, and immunoprecipitation-based methods have proven to be a powerful option. Such methods are rapidly shifting the bottleneck from data generation to data analysis, necessitating the development of better analytical tools. Until now, a major analytical difficulty associated with immunoprecipitation-based DNA methylation profiling has been the inability to estimate absolute methylation levels. Here we report the development of a novel cross-platform algorithm – Bayesian Tool for Methylation Analysis (Batman) – for analyzing Methylated DNA Immunoprecipitation (MeDIP) profiles generated using arrays (MeDIP-chip) or next-generation sequencing (MeDIP-seq). The latter is an approach we have developed to elucidate the first high-resolution whole-genome DNA methylation profile (DNA methylome) of any mammalian genome. MeDIP-seq/MeDIP-chip combined with Batman represent robust, quantitative, and cost-effective functional genomic strategies for elucidating the function of DNA methylation. PMID:18612301

Structural controls of the Tuscarora geothermal field, Elko County, Nevada

NASA Astrophysics Data System (ADS)

Dering, G.; Faulds, J. E.

2012-12-01

Tuscarora is an amagmatic geothermal system located ~90 km northwest of Elko, Nevada, in the northern part of the Basin and Range province ~15 km southeast of the Snake River Plain. Detailed geologic mapping, structural analysis, and well data have been integrated to identify the structural controls of the Tuscarora geothermal system. The structural framework of the geothermal field is defined by NNW- to NNE-striking normal faults that are approximately orthogonal to the present extension direction. Boiling springs, fumaroles, and siliceous sinter emanate from a single NNE-striking, west-dipping normal fault. Normal faults west of these hydrothermal features mostly dip steeply east, whereas normal faults east of the springs primarily dip west. Thus, the springs, fumaroles, and sinter straddle a zone of interaction between fault sets that dip toward each other, classified as a strike-parallel anticlinal accommodation zone. Faults within the geothermal area are mostly discontinuous along strike with offsets of tens to hundreds of meters, whereas the adjacent range-bounding fault systems of the Bull Run and Independence Mountains accommodate several kilometers of displacement. The geothermal field lies within a broad step over between the southward terminating west-dipping Bull Run fault zone and the northward terminating west-dipping Independence Mountains fault zone. Neither of these major fault zones is known to host high temperature geothermal systems. The accommodation zone lies within the broad step over and contains both east-dipping antithetic and west-dipping synthetic faults. Accommodation zones are relatively common structural components of extended terranes that transfer strain between oppositely dipping fault sets via a network of subsidiary normal faults. This study has identified the hinge zone of an anticlinal accommodation zone as the site most conducive to fluid up-flow. The recognition of this specific portion of an accommodation zone as a favorable structural setting for geothermal activity may be a useful exploration tool for development of drilling targets in extensional terranes, as well as for developing geologic models of known geothermal fields. This type of information may ultimately help to reduce the risks of targeting successful geothermal wells in such settings.

Iodide Residues in Milk Vary between Iodine-Based Teat Disinfectants.

PubMed

French, Elizabeth A; Mukai, Motoko; Zurakowski, Michael; Rauch, Bradley; Gioia, Gloria; Hillebrandt, Joseph R; Henderson, Mark; Schukken, Ynte H; Hemling, Thomas C

2016-07-01

Majority of iodine found in dairy milk comes from the diet and teat disinfection products used during milking process. The objective of this study was to evaluate the effects of 4 iodine-based teat dips on milk iodide concentrations varying in iodine level (0.25% vs. 0.5%, w/w), normal low viscosity dip versus barrier dip, and application method (dip vs. spray) to ensure safe iodine levels in dairy milk when these products are used. The iodine exposure study was performed during a 2-wk period. The trial farm was purged of all iodine-based disinfection products for 21 d during a prestudy "washout period," which resulted in baseline milk iodide range of 145 to 182 ppb. During the experiment, iodine-based teat dips were used as post-milking teat disinfectants and compared to a non-iodine control disinfectant. Milk iodide residue levels for each treatment was evaluated from composited group samples. Introduction of different iodine-based teat disinfectants increased iodide residue content in milk relative to the control by between 8 and 29 μg/L when averaged across the full trial period. However, residues levels for any treatment remained well below the consumable limit of 500 μg/L. The 0.5% iodine disinfectant increased milk iodide levels by 20 μg/L more compared to the 0.25% iodine. Compared to dip-cup application, spray application significantly increased milk iodide residue by 21 μg/L and utilized approximately 23% more teat dip. This carefully controlled study demonstrated an increase in milk iodide concentrations from iodine disinfectants, but increases were small and within acceptable limits. © 2016 Institute of Food Technologists®

Conductance dips and spin precession in a nonuniform waveguide with spin–orbit coupling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malyshev, A. I., E-mail: malyshev@phys.unn.ru; Kozulin, A. S.

An infinite waveguide with a nonuniformity, a segment of finite length with spin–orbit coupling, is considered in the case when the Rashba and Dresselhaus parameters are identical. Analytical expressions have been derived in the single-mode approximation for the conductance of the system for an arbitrary initial spin state. Based on numerical calculations with several size quantization modes, we have detected and described the conductance dips arising when the waves are localized in the nonuniformity due to the formation of an effective potential well in it. We show that allowance for the evanescent modes under carrier spin precession in an effectivemore » magnetic field does not lead to a change in the direction of the average spin vector at the output of the system.« less

Fabrication of Graphene on Kevlar Supercapacitor Electrodes

DTIC Science & Technology

2011-05-01

fabricated with graphene to investigate its applicability for energy storage devices, as this carbon- based material has a large surface area and...Distribution List 14 iv List of Figures Figure 1. Dip-and-dry technique applied to Kevlar- based electrodes...2  Figure 2. Three-electrode system used for the CV measurements. The (1) working electrode was the Kevlar- based electrode; (2) the counter

29 CFR 1910.124 - General requirements for dipping and coating operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... below 25% of its LFL. (2) When a liquid in a dip tank creates an exposure hazard covered by a standard... may use a tank cover or material that floats on the surface of the liquid in a dip tank to replace or... must: (1) Inspect the hoods and ductwork of the ventilation system for corrosion or damage: (i) At...

State reference design and saturated control of doubly-fed induction generators under voltage dips

NASA Astrophysics Data System (ADS)

Tilli, Andrea; Conficoni, Christian; Hashemi, Ahmad

2017-04-01

In this paper, the stator/rotor currents control problem of doubly-fed induction generator under faulty line voltage is carried out. Common grid faults cause a steep decline in the line voltage profile, commonly denoted as voltage dip. This point is critical for such kind of machines, having their stator windings directly connected to the grid. In this respect, solid methodological nonlinear control theory arguments are exploited and applied to design a novel controller, whose main goal is to improve the system behaviour during voltage dips, endowing it with low voltage ride through capability, a fundamental feature required by modern Grid Codes. The proposed solution exploits both feedforward and feedback actions. The feedforward part relies on suitable reference trajectories for the system internal dynamics, which are designed to prevent large oscillations in the rotor currents and command voltages, excited by line perturbations. The feedback part uses state measurements and is designed according to Linear Matrix Inequalities (LMI) based saturated control techniques to further reduce oscillations, while explicitly accounting for the system constraints. Numerical simulations verify the benefits of the internal dynamics trajectory planning, and the saturated state feedback action, in crucially improving the Doubly-Fed Induction Machine response under severe grid faults.

Milk caseins as useful vehicle for delivery of dipyridamole drug.

PubMed

Dezhampanah, Hamid; Esmaili, Masoomeh; Hasani, Leila

2018-05-01

The interaction of bovine milk α- and β-caseins as an efficient drug carrier system with Dipyridamole (DIP) was investigated using spectroscopy and molecular docking studies at different temperatures (20-37 °C). FTIR, CD, and fluorescence spectroscopy methods demonstrated that α- and β-caseins interact with DIP molecule mainly via hydrophobic and hydrophilic interactions and change in secondary structure of α- and β-caseins. DIP showed a higher quenching efficiency and binding constant of α-casein than β-casein. There was only one binding site for DIP and it was located on the surface of the protein molecule. The thermodynamic parameters of calculation showed that the binding process occurs spontaneously and demonstrated that α- and β-caseins provide very good binding and entrapment to DIP via hydrogen bonds, Van der Waals forces, and hydrophobic interactions. Fluorescence resonance energy transfer, synchronous fluorescence spectroscopy, and docking study showed that DIP binds to the Trp residues of α- and β-casein molecules with short distances. Docking study showed that DIP molecule made several hydrogen bonds and van der Waals interactions with α- and β-caseins. The study of cell culture and micellar solubility of DIP demonstrated α- and β-caseins relatively the same helping in delivery of DIP. Milk α- and β-caseins are considered as a useful vehicle for the solublization and stabilization of DIP in aqueous solution at natural pH.

Pseudomonas aeruginosa mastitis in two goats associated with an essential oil-based teat dip.

PubMed

Kelly, E Jane; Wilson, David J

2016-11-01

Pseudomonas aeruginosa is an opportunistic pathogen that has been associated with mastitis in dairy animals, including goats. Often, the environmental sources of the bacteria are water-related (such as hoses and muddy pastures). Mastitis attributable to P. aeruginosa was identified in 2 goats in a small herd. Efforts were made to identify environmental sources of the pathogen. Multiple samples from the goats' environment were cultured, including water from the trough, bedding, the hose used to wash udders, and the teat dip and teat dip containers. The bacterium was isolated from the teat dip and the teat dip container. The teat dip consisted of water, liquid soap, and several drops of essential oils (including tea tree, lavender, and peppermint). This case illustrates a potential problem that may arise as a result of the use of unconventional ingredients in teat dips. The use of alternative products by goat producers is likely to increase in the future. © 2016 The Author(s).

Voltage dips at the terminals of wind power installations

NASA Astrophysics Data System (ADS)

Bollen, Math H. J.; Olguin, Gabriel; Martins, Marcia

2005-07-01

This article gives an overview of the kind of voltage dips that can be expected at the terminals of a wind power installation. The overview is based on the study of those dips at the terminals of industrial installations and provides a guideline for the testing of wind power installations against voltage dips. For voltage dips due to faults, a classification into different types is presented. Five types appear at the terminals of sensitive equipment and thus have to be included when testing the wind power installation against disturbances coming from the grid. A distinction is made between installations connected at transmission level and those connected at distribution level. For the latter the phase angle jump has to be considered. Dips due to other causes (motor, transformer and capacitor switching) are briefly discussed as well as the voltage recovery after a dip. Finally some thoughts are presented on the way in which voltage tolerance requirements should be part of the design process for wind power installations. Copyright

Age and gender differences in conviction and crash occurrence subsequent to being directed to Iowa's driver improvement program.

PubMed

Zhang, Wei; Gkritza, Konstantina; Keren, Nir; Nambisan, Shashi

2011-10-01

This paper investigates potential gender and age differences in conviction and crash occurrence subsequent to being directed to attend Iowa's Driver Improvement Program (DIP). Binary logit models were developed to investigate the factors that influence conviction occurrence after DIP by gender and age. Because of the low crash occurrence subsequent to DIP, association rules were applied to investigate the factors that influence crash occurrence subsequent to DIP, in lieu of econometric models. There were statistical significant differences by driver gender, age, and conviction history in the likelihood of subsequent convictions. However, this paper found no association between DIP outcome, crash history, and crash occurrence. Evaluating the differences in conviction and crash occurrence subsequent to DIP between female and male drivers, and among different age groups can lead to improvements of the effectiveness of DIPs and help to identify low-cost intervention measures, customized based on drivers' gender and age, for improving driving behaviors. Copyright © 2011 National Safety Council and Elsevier Ltd. All rights reserved.

3D Model of the McGinness Hills Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

The McGinness Hills geothermal system lies in a ~8.5 km wide, north-northeast trending accommodation zone defined by east-dipping normal faults bounding the Toiyabe Range to the west and west-dipping normal faults bounding the Simpson Park Mountains to the east. Within this broad accommodation zone lies a fault step-over defined by north-northeast striking, west-dipping normal faults which step to the left at roughly the latitude of the McGinness Hills geothermal system. The McGinness Hills 3D model consists of 9 geologic units and 41 faults. The basal geologic units are metasediments of the Ordovician Valmy and Vininni Formations (undifferentiated in the model) which are intruded by Jurassic granitic rocks. Unconformably overlying is a ~100s m-thick section of Tertiary andesitic lava flows and four Oligocene-to-Miocene ash-flow tuffs: The Rattlesnake Canyon Tuff, tuff of Sutcliffe, the Cambell Creek Tuff and the Nine Hill tuff. Overlying are sequences of pre-to-syn-extensional Quaternary alluvium and post-extensional Quaternary alluvium. 10-15º eastward dip of the Tertiary stratigraphy is controlled by the predominant west-dipping fault set. Geothermal production comes from two west dipping normal faults in the northern limb of the step over. Injection is into west dipping faults in the southern limb of the step over. Production and injection sites are in hydrologic communication, but at a deep level, as the northwest striking fault that links the southern and northern limbs of the step-over has no permeability.

Seismicity and structure of Nazca Plate subduction zone in southern Peru

NASA Astrophysics Data System (ADS)

Lim, H.; Kim, Y.; Clayton, R. W.

2015-12-01

We image the Nazca plate subduction zone system by detecting and (re)locating intra-slab earthquakes in southern Peru. Dense seismic arrays (PeruSE, 2013) were deployed along four lines to target geophysical characterization of the subduction system in the transition zone between flat and normal dipping segments of the Nazca plate (2-15°S). The arc volcanism is absent near the flat slab segment, and currently, the correlation between the location of the active volcanic front and corresponding slab depth is neither clear nor consistent between previously published models from seismicity. We detect 620 local earthquakes from August 2008 to February 2013 by manually picking 6559 and 4145 arrival times for P- and S-phases, respectively. We observe that the S-phase data is helpful to reduce the trade-off between origin time and depth of deeper earthquakes (>100 km). Earthquake locations are relocated to constrain the Nazca slab-mantle interface in the slab-dip transition zone using 7322 measurements of differential times of nearby earthquake pairs by waveform cross-correlation. We also employ the double-difference tomography (Zhang and Thurber, 2003) to further improve earthquake source locations and the spatial resolution of the velocity structure simultaneously. The relocated hypocenters clearly delineate the dipping Wadati-Benioff zone in the slab-dip transition zone between the shallow- (25°) to-flat dipping slab segment in the north and the normal (40°) dipping segment in the south. The intermediate-depth seismicity in the flat slab region stops at a depth of ~100 km and a horizontal distance of ~400 km from the trench. We find a significant slab-dip difference (up to 10°) between our relocated seismicity and previously published slab models along the profile region sampling the normal-dip slab at depth (>100 km).

The state of the art of the development of SMES for bridging instantaneous voltage dips in Japan

NASA Astrophysics Data System (ADS)

Nagaya, Shigeo; Hirano, Naoki; Katagiri, Toshio; Tamada, Tsutomu; Shikimachi, Koji; Iwatani, Yu; Saito, Fusao; Ishii, Yusuke

2012-12-01

Development of apparatuses for protecting industrial facilities such as semiconductor plants or information industries from instantaneous voltage dips, which requires very large output power, has been expected. A Superconducting magnetic energy storage system (SMES), one of such apparatus, consists of superconducting magnets that must withstand high voltage during operation and require high reliability. We have already development of SMES using conventional superconducting coils and done the field test of the SMES for bridging instantaneous voltage dips. After field test, the commercial SMES for instantaneous voltage dips is working there. Since field test has started, we have confirmed nearly 40 operations, and all have succeeded. In 2011, three commercial SMES units for bridging instantaneous voltage dips are operating in Japan.

Updating the orbital ephemeris of the dipping source XB 1254-690 and the distance to the source

NASA Astrophysics Data System (ADS)

Gambino, Angelo F.; Iaria, Rosario; Di Salvo, Tiziana; Matranga, Marco; Burderi, Luciano; Pintore, Fabio; Riggio, Alessandro; Sanna, Andrea

2017-09-01

XB 1254-690 is a dipping low mass X-ray binary system hosting a neutron star and showing type I X-ray bursts. We aim at obtaining a more accurate orbital ephemeris and at constraining the orbital period derivative of the system for the first time. In addition, we want to better constrain the distance to the source in order to locate the system in a well defined evolutive scenario. We apply, for the first time, an orbital timing technique to XB 1254-690, using the arrival times of the dips present in the light curves that have been collected during 26 yr of X-ray pointed observations acquired from different space missions. We estimate the dip arrival times using a statistical method that weights the count-rate inside the dip with respect to the level of persistent emission outside the dip. We fit the obtained delays as a function of the orbital cycles both with a linear and a quadratic function. We infer the orbital ephemeris of XB 1254-690, improving the accuracy of the orbital period with respect to previous estimates. We infer a mass of M 2 = 0.42 ± 0.04 M ʘ for the donor star, in agreement with estimations already present in literature, assuming that the star is in thermal equilibrium while it transfers part of its mass via the inner Lagrangian point, and assuming a neutron star mass of 1.4 M ʘ. Using these assumptions, we also constrain the distance to the source, finding a value of 7.6 ± 0.8 kpc. Finally, we discuss the evolution of the system, suggesting that it is compatible with a conservative mass transfer driven by magnetic braking.

Dense protective coatings, methods for their preparation and coated articles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tulyani, Sonia; Bhatia, Tania; Smeggil, John G.

A method for depositing a protective coating on a complex shaped substrate includes the steps of: (1) dipping a complex shaped substrate into a slurry to form a base coat thereon, the slurry comprising an aqueous solution, at least one refractory metal oxide, and at least one transient fluid additive present in an amount of about 0.1 percent to 10 percent by weight of the slurry; (2) curing the dipped substrate; (3) dipping the substrate into a precursor solution to form a top barrier coat thereon; and (4) heat treating the dipped, cured substrate to form a protective coating.

'Where's the flux' star: Where's the excess?

NASA Astrophysics Data System (ADS)

Meng, Huan; Boyajian, Tabetha; Kennedy, Grant; Lisse, Carey; Marengo, Massimo; Wright, Jason; Wyatt, Mark

2018-05-01

KIC 8462852 provides, in real time, the rare chance to observe cataclysmic events happening in a mature extrasolar planetary system. The Kepler light curve of the star sees two major dips 750 days apart with depths of 20%, as well as a number of smaller dips ( 1%) at apparently random time. A series of new, shallow (2-4% in flux) dips has been observed since May 2017 and as late as March 2018. In addition to the days-long dips, the star has also been found to have long-term variations over years, and possibly centuries. Conclusions from existing observations suggest that the dips and long-term variations are likely caused by transits of dust clumps in front of the star. We have observed KIC 8462852 with Spitzer/IRAC since cycle 12. We propose to continue the monitoring in cycle 14 to track the long-term variations of the stellar flux, measure the optical properties of the transit dust, and look for possible transient excess if new dips happen close in time to our observations.

3D Model of the Neal Hot Springs Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

The Neal Hot Springs geothermal system lies in a left-step in a north-striking, west-dipping normal fault system, consisting of the Neal Fault to the south and the Sugarloaf Butte Fault to the north (Edwards, 2013). The Neal Hot Springs 3D geologic model consists of 104 faults and 13 stratigraphic units. The stratigraphy is sub-horizontal to dipping <10 degrees and there is no predominant dip-direction. Geothermal production is exclusively from the Neal Fault south of, and within the step-over, while geothermal injection is into both the Neal Fault to the south of the step-over and faults within the step-over.

Deformation Analyses and Lithologic Characterization in Overpressured Basins Based on Logging While Drilling and Wireline Results from the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Iturrino, G. J.; Pirmez, C.; Moore, J. C.; Reichow, M. K.; Dugan, B. E.; Sawyer, D. E.; Flemings, P. B.; Shipboard Scientific Party, I.

2005-12-01

IODP Expedition 308 drilled transects along the Brazos-Trinity IV and Ursa Basins in the western and eastern Gulf of Mexico, respectively, for examining how sedimentation, overpressure, fluid flow, and deformation are coupled in passive margin settings. A total of eight holes were logged using either logging while drilling (LWD) or wireline techniques to evaluate the controls on slope stability, understand the timing of sedimentation and slumping, establish the petrophysical properties of shallow sediments, and provide a better understanding of turbidite systems. Overall, the log responses vary for the different lithostratigraphic units and associated regional seismic reflectors. The data acquired also make bed-to-bed correlation between sites possible, which is valuable for the study of sandy turbidites and studies of regional deformation. The thick sedimentary successions drilled at these basins show records of the evolution of channel-levee systems composed of low relief channels that were incapable of confining the turbidity currents causing an overspill of sand and silt. In addition, mass transport deposits at shallow depths, and transitions between interbedded silt, sand, and mud units are common features identified in many of the downhole logging data. In the Ursa Basin sediments, resistivity-at-the-bit images show significant deformation of the overlying hemipelagic drape and distal turbidites that were drilled in these areas. Numerous dipping beds throughout these intervals with dips ranging from 5 to 55 degrees confirm core observations. Steeply deformed beds, with dips as high as 65 degrees, and folded and faulted beds suggest down slope remobilization as mass-transport deposits. Resistivity images also show evidence of these mass-transport deposits where steep dips and folds suggest the presence of overturned beds within a series of cyclic intervals that we interpret as a succession of sand-silt-mud lamina. Preliminary structural analyses suggest that many of the deformation features trend in an E-W direction with the majority dipping to the north.

Power Systems for Future Missions: Appendices A-L

NASA Technical Reports Server (NTRS)

Gill, S. P.; Frye, P. E.; Littman, Franklin D.; Meisl, C. J.

1994-01-01

Selection of power system technology for space applications is typically based on mass, readiness of a particular technology to meet specific mission requirements, and life cycle costs (LCC). The LCC is typically used as a discriminator between competing technologies for a single mission application. All other future applications for a given technology are usually ignored. As a result, development cost of a technology becomes a dominant factor in the LCC comparison. Therefore, it is common for technologies such as DIPS and LMR-CBC to be potentially applicable to a wide range of missions and still lose out in the initial LCC comparison due to high development costs. This collection of appendices (A through L) contains the following power systems technology plans: CBC DIPS Technology Roadmap; PEM PFC Technology Roadmap; NAS Battery Technology Roadmap; PV/RFC Power System Technology Roadmap; PV/NAS Battery Technology Roadmap; Thermionic Reactor Power System Technology Roadmap; SP-100 Power System Technology Roadmap; Dynamic SP-100 Power System Technology Roadmap; Near-Term Solar Dynamic Power System Technology Roadmap; Advanced Solar Dynamic Power System Technology Roadmap; Advanced Stirling Cycle Dynamic Isotope Power System Technology Roadmap; and the ESPPRS (Evolutionary Space Power and Propulsion Requirements System) User's Guide.

Evaluation of spatial variability of soil arsenic adjacent to a disused cattle-dip site, using model-based geostatistics.

PubMed

Niazi, Nabeel K; Bishop, Thomas F A; Singh, Balwant

2011-12-15

This study investigated the spatial variability of total and phosphate-extractable arsenic (As) concentrations in soil adjacent to a cattle-dip site, employing a linear mixed model-based geostatistical approach. The soil samples in the study area (n = 102 in 8.1 m(2)) were taken at the nodes of a 0.30 × 0.35 m grid. The results showed that total As concentration (0-0.2 m depth) and phosphate-extractable As concentration (at depths of 0-0.2, 0.2-0.4, and 0.4-0.6 m) in soil adjacent to the dip varied greatly. Both total and phosphate-extractable soil As concentrations significantly (p = 0.004-0.048) increased toward the cattle-dip. Using the linear mixed model, we suggest that 5 samples are sufficient to assess a dip site for soil (As) contamination (95% confidence interval of ±475.9 mg kg(-1)), but 15 samples (95% confidence interval of ±212.3 mg kg(-1)) is desirable baseline when the ultimate goal is to evaluate the effects of phytoremediation. Such guidelines on sampling requirements are crucial for the assessment of As contamination levels at other cattle-dip sites, and to determine the effect of phytoremediation on soil As.

Tribology and Tool Wear of Hot Dip Galvanized Zinc Magnesium Alloys on Cold Rolled Steel Sheets

NASA Astrophysics Data System (ADS)

Raab, A. E.; Berger, E.; Freudenthaler, J.; Leomann, F.; Walch, C.

2011-05-01

Recently zinc based coatings on cold rolled steel with improved functionality in terms of forming and/or corrosion behaviour have been intensively investigated in the steel industry1,2,3. One of the most promising products are zinc magnesium alloys produced in hot dip galvanizing process. These coatings were already introduced in construction industry a few years ago1. With some modifications the improved properties of the coating are also interesting for automotive industry. In the present work the tribological potential of hot dip galvanized zinc magnesium coatings (HDG/ZM) produced at an industrial line under regular production, was studied in terms of sliding properties, adhesive and abrasive tool wear. First a short introduction into surface morphology of HDG/ZM will be given. For the tribological characterization of the material, which is the main topic of the contribution, different tests were performed on hot dip galvanised zinc magnesium material and results were compared with classic hot dip galvanized zinc coating (HDG/Z). The investigations are mainly based on the strip draw test which allows the determination of the friction coefficient directly by using a constant contact pressure. Deep drawing property was tested by forming model cups. The abrasive tool wear was tested using a standard test for material used in automotive industry. The adhesive tool wear was investigated by characterizing the coating material transferred to the tool in the strip draw test. All performed tests show an improved drawability of HDG/ZM compared to classical HDG/Z reference material. However the most promising difference between HDG/ZM and HDG/Z is that galling was found to be less for HDG/ZM than for HDG/Z. Therefore HDG/ZM is an interesting system not only with respect to corrosion protection but also in terms of tribology and provides clear advantages in formability.

Tribology and Tool Wear of Hot Dip Galvanized Zinc Magnesium Alloys on Cold Rolled Steel Sheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raab, A. E.; Berger, E.; Freudenthaler, J.

Recently zinc based coatings on cold rolled steel with improved functionality in terms of forming and/or corrosion behaviour have been intensively investigated in the steel industry. One of the most promising products are zinc magnesium alloys produced in hot dip galvanizing process. These coatings were already introduced in construction industry a few years ago. With some modifications the improved properties of the coating are also interesting for automotive industry. In the present work the tribological potential of hot dip galvanized zinc magnesium coatings (HDG/ZM) produced at an industrial line under regular production, was studied in terms of sliding properties, adhesivemore » and abrasive tool wear.First a short introduction into surface morphology of HDG/ZM will be given. For the tribological characterization of the material, which is the main topic of the contribution, different tests were performed on hot dip galvanised zinc magnesium material and results were compared with classic hot dip galvanized zinc coating (HDG/Z). The investigations are mainly based on the strip draw test which allows the determination of the friction coefficient directly by using a constant contact pressure. Deep drawing property was tested by forming model cups. The abrasive tool wear was tested using a standard test for material used in automotive industry. The adhesive tool wear was investigated by characterizing the coating material transferred to the tool in the strip draw test.All performed tests show an improved drawability of HDG/ZM compared to classical HDG/Z reference material. However the most promising difference between HDG/ZM and HDG/Z is that galling was found to be less for HDG/ZM than for HDG/Z. Therefore HDG/ZM is an interesting system not only with respect to corrosion protection but also in terms of tribology and provides clear advantages in formability.« less

Recent photometric monitoring of KIC 8462852, the detection of a potential repeat of the Kepler day 1540 dip and a plausible model

NASA Astrophysics Data System (ADS)

Bourne, R.; Gary, B. L.; Plakhov, A.

2018-04-01

This paper presents V- and g΄-band observations of the F2V star KIC 8462852, which exhibited enigmatic fade patterns in Kepler mission data. We introduce a transit simulation model for interpretation of these fades, and use it to interpret a 2017 August dip as a repeat of the Kepler day 1540 dip (D1540). We suggest the 2017 August and D1540 dips may be caused by a brown dwarf and an associated ring system in a 1601-d elliptical orbit. Transiting icy moons of the proposed brown dwarf, sublimating near periapsis like comets, could provide an explanation for the significant dips observed by Kepler, as well as the recent 2017 May to October dips and the long-term variation in flux detected by Simon et al. Whereas the presence of such a ring structure is attractive for its ability to explain short-term fade events, we do not address how such a ring system can be created and maintained. This speculation predicted a brightening of ˜1 per cent that occurred during October 2017. In addition, this scenario predicts that a set of dimming events, similar to those in 2013 (Kepler) and in 2017 (reported here), can be expected to repeat during 2021 October to 2022 January and a repeat of D1540 should occur on 2021 December 27.

DISCO Interacting Protein 2 regulates axonal bifurcation and guidance of Drosophila mushroom body neurons.

PubMed

Nitta, Yohei; Yamazaki, Daisuke; Sugie, Atsushi; Hiroi, Makoto; Tabata, Tetsuya

2017-01-15

Axonal branching is one of the key processes within the enormous complexity of the nervous system to enable a single neuron to send information to multiple targets. However, the molecular mechanisms that control branch formation are poorly understood. In particular, previous studies have rarely addressed the mechanisms underlying axonal bifurcation, in which axons form new branches via splitting of the growth cone. We demonstrate that DISCO Interacting Protein 2 (DIP2) is required for precise axonal bifurcation in Drosophila mushroom body (MB) neurons by suppressing ectopic bifurcation and regulating the guidance of sister axons. We also found that DIP2 localize to the plasma membrane. Domain function analysis revealed that the AMP-synthetase domains of DIP2 are essential for its function, which may involve exerting a catalytic activity that modifies fatty acids. Genetic analysis and subsequent biochemical analysis suggested that DIP2 is involved in the fatty acid metabolization of acyl-CoA. Taken together, our results reveal a function of DIP2 in the developing nervous system and provide a potential functional relationship between fatty acid metabolism and axon morphogenesis. Copyright © 2016 Elsevier Inc. All rights reserved.

Comparison of dynamic isotope power systems for distributed planet surface applications

NASA Technical Reports Server (NTRS)

Bents, David J.; Mckissock, Barbara I.; Hanlon, James C.; Schmitz, Paul C.; Rodriguez, Carlos D.; Withrow, Colleen A.

1991-01-01

Dynamic isotope power system (DIPS) alternatives were investigated and characterized for the surface mission elements associated with a lunar base and subsequent manned Mars expedition. System designs based on two convertor types were studied. These systems were characterized parametrically and compared over the steady-state electrical output power range 0.2 to 20 kWe. Three methods of thermally integrating the heat source and the Stirling heater head were considered, depending on unit size. Figures of merit were derived from the characterizations and compared over the parametric range. Design impacts of mission environmental factors are discussed and quantitatively assessed.

The SCEC 3D Community Fault Model (CFM-v5): An updated and expanded fault set of oblique crustal deformation and complex fault interaction for southern California

NASA Astrophysics Data System (ADS)

Nicholson, C.; Plesch, A.; Sorlien, C. C.; Shaw, J. H.; Hauksson, E.

2014-12-01

Southern California represents an ideal natural laboratory to investigate oblique deformation in 3D owing to its comprehensive datasets, complex tectonic history, evolving components of oblique slip, and continued crustal rotations about horizontal and vertical axes. As the SCEC Community Fault Model (CFM) aims to accurately reflect this 3D deformation, we present the results of an extensive update to the model by using primarily detailed fault trace, seismic reflection, relocated hypocenter and focal mechanism nodal plane data to generate improved, more realistic digital 3D fault surfaces. The results document a wide variety of oblique strain accommodation, including various aspects of strain partitioning and fault-related folding, sets of both high-angle and low-angle faults that mutually interact, significant non-planar, multi-stranded faults with variable dip along strike and with depth, and active mid-crustal detachments. In places, closely-spaced fault strands or fault systems can remain surprisingly subparallel to seismogenic depths, while in other areas, major strike-slip to oblique-slip faults can merge, such as the S-dipping Arroyo Parida-Mission Ridge and Santa Ynez faults with the N-dipping North Channel-Pitas Point-Red Mountain fault system, or diverge with depth. Examples of the latter include the steep-to-west-dipping Laguna Salada-Indiviso faults with the steep-to-east-dipping Sierra Cucapah faults, and the steep southern San Andreas fault with the adjacent NE-dipping Mecca Hills-Hidden Springs fault system. In addition, overprinting by steep predominantly strike-slip faulting can segment which parts of intersecting inherited low-angle faults are reactivated, or result in mutual cross-cutting relationships. The updated CFM 3D fault surfaces thus help characterize a more complex pattern of fault interactions at depth between various fault sets and linked fault systems, and a more complex fault geometry than typically inferred or expected from projecting near-surface data down-dip, or modeled from surface strain and potential field data alone.

Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

NASA Astrophysics Data System (ADS)

Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

Detection of sedimentary structural elements using formation micro imager technique, a case study from South Mansoura-1 well, Nile Delta, Egypt

NASA Astrophysics Data System (ADS)

Abd El-Wahed, Ahmed G.; Anan, Tarek I.

2016-12-01

A detailed structure and sedimentology interpretation was performed for the South Mansoura-1 well. The Formation Micro Imager (FMI) is recorded and interpreted over the interval 9100-8009 ft. This interval belongs to Sidi Salem and Qawasim Formations. Based on azimuth trend of manually picked dips (bed boundaries), the interval can be divided into 4 structural dip zones (Zone 1 (9100-8800 ft), variable azimuth direction with the major trends mainly to SW&NE; Zone 2 (8800-8570 ft), bedding dip azimuth is mainly to the NW; Zone 3 (8570-8250 ft), bedding dip azimuth is mainly to the NE; and Zone 4 (8250-8009 ft), bedding dip azimuth is mainly to the NW). Lamination identified over the interval shows a dominant dip azimuth trend toward North North-West direction. The interbedded shale units are highly laminated and show little evidence of bioturbation. Sand exhibits abundant cross bedding showing a dominant dip azimuth trends toward NNE and NE and more locally to the E. Sixteen truncations identified over the interval show variable azimuth trend with the major trend mainly to the North North-West.

Electrochemical pesticide detection with AutoDip--a portable platform for automation of crude sample analyses.

PubMed

Drechsel, Lisa; Schulz, Martin; von Stetten, Felix; Moldovan, Carmen; Zengerle, Roland; Paust, Nils

2015-02-07

Lab-on-a-chip devices hold promise for automation of complex workflows from sample to answer with minimal consumption of reagents in portable devices. However, complex, inhomogeneous samples as they occur in environmental or food analysis may block microchannels and thus often cause malfunction of the system. Here we present the novel AutoDip platform which is based on the movement of a solid phase through the reagents and sample instead of transporting a sequence of reagents through a fixed solid phase. A ball-pen mechanism operated by an external actuator automates unit operations such as incubation and washing by consecutively dipping the solid phase into the corresponding liquids. The platform is applied to electrochemical detection of organophosphorus pesticides in real food samples using an acetylcholinesterase (AChE) biosensor. Minimal sample preparation and an integrated reagent pre-storage module hold promise for easy handling of the assay. Detection of the pesticide chlorpyrifos-oxon (CPO) spiked into apple samples at concentrations of 10(-7) M has been demonstrated. This concentration is below the maximum residue level for chlorpyrifos in apples defined by the European Commission.

Origin of Dips in 4U1915-05

NASA Technical Reports Server (NTRS)

Grindlay, Jonathan E.

2003-01-01

This grant supported our participation in a proposal submitted by Didier Barret to conduct a study of the dipping LMXB 4U1915-05. In this Final Report, we summarize the Scientific Objectives of this investigation and the results achieved. Data analysis is still in progress and publication of results will be forthcoming.Our objectives in this work have been to study: 1. Spectra of dips in 4 Ul916-05: This low mass x-ray binary (LMXB) is a 50min binary system and the first to show x-ray dip behaviour. Our XMM observation was proposed to study the x-ray spectra of the dips to better constrain their physical properties. Of primary interest is the variation of the absorbing column density as a function of flux in the dip. We wish to isolate the absorption from Compton scattering components in the dip spectra, and to use the large throughput of XMM to better constrain short timescale variations of the spectrum in the dips. 2. Period of the dips and long-term ephemeris: We also seek to improve upon the long- term ephemeris of the dips by combining these more recent XMM data with earlier RXTE data to update the ephemeris for dips and the determination of the dip period to further test whether the dip period represents the true binary period of this LMXB. We shall extend the ephemeris published by Chou, Grindlay and Bloser 2001, ApJ, 549, 1135) to test the assertion of Retter, Chou et a1 2002, MNRAS, 330, 37 that the dips are indeed the binary period and not a precession period. 1 3 Results Achieved The observations for this program were delayed, presumably for reasons related to the general difficulty of scheduling XMM targets in this region moderately close to the Cygnus region. 4'171916-05 was finally observed (2lksec) on April 24, 2002, but the data have not been delivered. A second observation was conducted on September 9, 2002 (18ksec) and the data are still being analyzed. 4 Papers Presented and Published A paper is in preparation for Astronomy and Astrophysics in which the full results of this investigation will be reported. 1. Barret, D. et a1 2003, Astron. and Astophys.,in press. 2

Microplate-based platform for combined chromatin and DNA methylation immunoprecipitation assays

PubMed Central

2011-01-01

Background The processes that compose expression of a given gene are far more complex than previously thought presenting unprecedented conceptual and mechanistic challenges that require development of new tools. Chromatin structure, which is regulated by DNA methylation and histone modification, is at the center of gene regulation. Immunoprecipitations of chromatin (ChIP) and methylated DNA (MeDIP) represent a major achievement in this area that allow researchers to probe chromatin modifications as well as specific protein-DNA interactions in vivo and to estimate the density of proteins at specific sites genome-wide. Although a critical component of chromatin structure, DNA methylation has often been studied independently of other chromatin events and transcription. Results To allow simultaneous measurements of DNA methylation with other genomic processes, we developed and validated a simple and easy-to-use high throughput microplate-based platform for analysis of DNA methylation. Compared to the traditional beads-based MeDIP the microplate MeDIP was more sensitive and had lower non-specific binding. We integrated the MeDIP method with a microplate ChIP assay which allows measurements of both DNA methylation and histone marks at the same time, Matrix ChIP-MeDIP platform. We illustrated several applications of this platform to relate DNA methylation, with chromatin and transcription events at selected genes in cultured cells, human cancer and in a model of diabetic kidney disease. Conclusion The high throughput capacity of Matrix ChIP-MeDIP to profile tens and potentially hundreds of different genomic events at the same time as DNA methylation represents a powerful platform to explore complex genomic mechanism at selected genes in cultured cells and in whole tissues. In this regard, Matrix ChIP-MeDIP should be useful to complement genome-wide studies where the rich chromatin and transcription database resources provide fruitful foundation to pursue mechanistic, functional and diagnostic information at genes of interest in health and disease. PMID:22098709

Diversification of CYCLOIDEA expression in the evolution of bilateral flower symmetry in Caprifoliaceae and Lonicera (Dipsacales)

PubMed Central

Howarth, Dianella G.; Martins, Tiago; Chimney, Edward; Donoghue, Michael J.

2011-01-01

Background and Aims The expression of floral symmetry genes is examined in the CYCLOIDEA lineage following duplication, and these are linked to changes in flower morphology. The study focuses on Dipsacales, comparing DipsCYC2 gene expression in Viburnum (radially symmetrical Adoxaceae) to members of early-diverging lineages of the bilaterally symmetrical Caprifoliaceae (Diervilla and Lonicera). Methods Floral tissue from six species, which included dorsal, lateral and ventral regions of the corolla, was dissected. RNA was extracted from these tissues and each copy of DipsCYC2 was amplified with reverse transcriptase PCR. Key Results Members of DipsCYC2 were expressed across the corolla in the radially symmetrical Viburnum plicatum. A shift to bilaterally symmetrical flowers at the base of the Caprifoliaceae was accompanied by a duplication of the DipsCYC2 gene, resulting in DipsCYC2A and DipsCYC2B, and by loss of expression of both of these copies in the ventral petal. In Lonicera (Caprifolieae), there is a shift from flowers with two dorsally and three ventrally oriented corolla lobes to a clear differentiation of dorsal, lateral and ventral lobes. This shift entailed a decoupling of expression of DipsCYC2A and DipsCYC2B; DipsCYC2B continues to be expressed in the dorsal and lateral lobes, while DipsCYC2A expression is restricted to just the two dorsal lobes. A reversion to more radially symmetrical flowers within Lonicera was accompanied by a re-expansion of expression of both DipsCYC2A and DipsCYC2B. Conclusions The transition to bilateral symmetry in Caprifoliaceae involved: (a) duplication of an ancestral DipsCYC2 gene; (b) the loss of expression of both of these copies in the ventral petal; and (c) changes in the zone of expression, with one copy continuing to be expressed across the dorsal and lateral petals, and the other copy becoming restricted in expression to the dorsal corolla lobes. PMID:21478175

Approach to fitting parameters and clustering for characterising measured voltage dips based on two-dimensional polarisation ellipses

DOE Office of Scientific and Technical Information (OSTI.GOV)

García-Sánchez, Tania; Gómez-Lázaro, Emilio; Muljadi, E.

An alternative approach to characterise real voltage dips is proposed and evaluated in this study. The proposed methodology is based on voltage-space vector solutions, identifying parameters for ellipses trajectories by using the least-squares algorithm applied on a sliding window along the disturbance. The most likely patterns are then estimated through a clustering process based on the k-means algorithm. The objective is to offer an efficient and easily implemented alternative to characterise faults and visualise the most likely instantaneous phase-voltage evolution during events through their corresponding voltage-space vector trajectories. This novel solution minimises the data to be stored but maintains extensivemore » information about the dips including starting and ending transients. The proposed methodology has been applied satisfactorily to real voltage dips obtained from intensive field-measurement campaigns carried out in a Spanish wind power plant up to a time period of several years. A comparison to traditional minimum root mean square-voltage and time-duration classifications is also included in this study.« less

Dip and anisotropy effects on flow using a vertically skewed model grid.

PubMed

Hoaglund, John R; Pollard, David

2003-01-01

Darcy flow equations relating vertical and bedding-parallel flow to vertical and bedding-parallel gradient components are derived for a skewed Cartesian grid in a vertical plane, correcting for structural dip given the principal hydraulic conductivities in bedding-parallel and bedding-orthogonal directions. Incorrect-minus-correct flow error results are presented for ranges of structural dip (0 < or = theta < or = 90) and gradient directions (0 < or = phi < or = 360). The equations can be coded into ground water models (e.g., MODFLOW) that can use a skewed Cartesian coordinate system to simulate flow in structural terrain with deformed bedding planes. Models modified with these equations will require input arrays of strike and dip, and a solver that can handle off-diagonal hydraulic conductivity terms.

Longitudinal variability of complexities associated with equatorial electrojet

NASA Astrophysics Data System (ADS)

Rabiu, A. B.; Ogunjo, S. T.; Fuwape, I. A.

2017-12-01

Equatorial electrojet indices obtained from ground based magnetometers at 6 representative stations across the magnetic equatorial belt for the year 2009 (mean annual sunspot number Rz = 3.1) were treated to nonlinear time series analysis technique to ascertain the longitudinal dependence of the chaos/complexities associated with the phenomena. The selected stations were along the magnetic equator in the South American (Huancayo, dip latitude -1.80°), African (Ilorin, dip latitude -1.82°; Addis Ababa, dip latitude - 0.18°), and Philippine (Langkawi, dip latitude -2.32°; Davao, dip latitude -1.02°; Yap, dip latitude -1.49°) sectors. The non-linear quantifiers engaged in this work include: Recurrence rate, determinism, diagonal line length, entropy, laminarity, Tsallis entropy, Lyapunov exponent and correlation dimension. Ordinarily the EEJ was found to undergo variability from one longitudinal representative station to another, with the strongest EEJ of about 192.5 nT at the South American axis at Huancayo. The degree of complexity in the EEJ was found to vary qualitatively from one sector to another. Probable physical mechanisms responsible for longitudinal variability of EEJ strength and its complexities were highlighted.

A new target ligand Ser-Glu for PEPT1-overexpressing cancer imaging.

PubMed

Dai, Tongcheng; Li, Na; Zhang, Lingzhi; Zhang, Yuanxing; Liu, Qin

2016-01-01

Nanoparticles functionalized with active target ligands have been widely used for tumor-specific diagnosis and therapy. The target ligands include antibodies, peptides, proteins, small molecules, and nucleic acid aptamers. Here, we utilize dipeptide Ser-Glu (DIP) as a new ligand to functionalize polymer-based fluorescent nanoparticles (NPs) for pancreatic cancer target imaging. We demonstrate that in the first step, Ser-Glu-conjugated NPs (NPs-DIP) efficiently bind to AsPC-1 and in the following NPs-DIP are internalized into AsPC-1 in vitro. The peptide transporter 1 inhibition experiment reveals that the targeting effects mainly depend on the specific binding of DIP to peptide transporter 1, which is remarkably upregulated in pancreatic cancer cells compared with varied normal cells. Furthermore, NPs-DIP specifically accumulate in the site of pancreatic tumor xenograft and are further internalized into the tumor cells in vivo after intravenous administration, indicating that DIP successfully enhanced nanoparticles internalization efficacy into tumor cells in vivo. This work establishes Ser-Glu to be a new tumor-targeting ligand and provides a promising tool for future tumor diagnostic or therapeutic applications.

Development of flow-through and dip-stick immunoassays for screening of sulfonamide residues.

PubMed

Zhang, Hongyan; Zhang, Yan; Wang, Shuo

2008-08-20

Two formats of membrane-based competitive enzyme immunoassays (flow-through and dip-stick) have been developed for the screening of sulfonamide residues in pig muscle and milk. Membrane was coated with anti-sulfonamide antibody and a sulfonamide hapten D2-horseradish peroxidase (HRP) conjugant was used as the labeled antigen for competitive assay of sulfonamides. Visual detection limits of the flow-through or dip-stick assay were 1-5 microg L(-1) or 1-10 microg L(-1) in buffer for seven sulfonamides, respectively. Assay validation was performed using samples spiked with single sulfonamide, spiked samples were tested using the developed strip assays and results were compared with those obtained by a validated high-performance liquid chromatograph (HPLC) method. Results showed that the two strip assays were correlated well with HPLC, respectively. With assay times of 5 min (flow-through) and 15 min (dip-stick), these rapid tests could offer simple, rapid and cost-effective on-site screening tools to detect sulfonamides in pig muscle (flow-through or dip-stick) or milk (only dip-stick).

3D Model of the Tuscarora Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

The Tuscarora geothermal system sits within a ~15 km wide left-step in a major west-dipping range-bounding normal fault system. The step over is defined by the Independence Mountains fault zone and the Bull Runs Mountains fault zone which overlap along strike. Strain is transferred between these major fault segments via and array of northerly striking normal faults with offsets of 10s to 100s of meters and strike lengths of less than 5 km. These faults within the step over are one to two orders of magnitude smaller than the range-bounding fault zones between which they reside. Faults within the broad step define an anticlinal accommodation zone wherein east-dipping faults mainly occupy western half of the accommodation zone and west-dipping faults lie in the eastern half of the accommodation zone. The 3D model of Tuscarora encompasses 70 small-offset normal faults that define the accommodation zone and a portion of the Independence Mountains fault zone, which dips beneath the geothermal field. The geothermal system resides in the axial part of the accommodation, straddling the two fault dip domains. The Tuscarora 3D geologic model consists of 10 stratigraphic units. Unconsolidated Quaternary alluvium has eroded down into bedrock units, the youngest and stratigraphically highest bedrock units are middle Miocene rhyolite and dacite flows regionally correlated with the Jarbidge Rhyolite and modeled with uniform cumulative thickness of ~350 m. Underlying these lava flows are Eocene volcanic rocks of the Big Cottonwood Canyon caldera. These units are modeled as intracaldera deposits, including domes, flows, and thick ash deposits that change in thickness and locally pinch out. The Paleozoic basement of consists metasedimenary and metavolcanic rocks, dominated by argillite, siltstone, limestone, quartzite, and metabasalt of the Schoonover and Snow Canyon Formations. Paleozoic formations are lumped in a single basement unit in the model. Fault blocks in the eastern portion of the model are tilted 5-30 degrees toward the Independence Mountains fault zone. Fault blocks in the western portion of the model are tilted toward steeply east-dipping normal faults. These opposing fault block dips define a shallow extensional anticline. Geothermal production is from 4 closely-spaced wells, that exploit a west-dipping, NNE-striking fault zone near the axial part of the accommodation zone.

Angular shaping of fluorescence from synthetic opal-based photonic crystal.

PubMed

Boiko, Vitalii; Dovbeshko, Galyna; Dolgov, Leonid; Kiisk, Valter; Sildos, Ilmo; Loot, Ardi; Gorelik, Vladimir

2015-01-01

Spectral, angular, and temporal distributions of fluorescence as well as specular reflection were investigated for silica-based artificial opals. Periodic arrangement of nanosized silica globules in the opal causes a specific dip in the defect-related fluorescence spectra and a peak in the reflectance spectrum. The spectral position of the dip coincides with the photonic stop band. The latter is dependent on the size of silica globules and the angle of observation. The spectral shape and intensity of defect-related fluorescence can be controlled by variation of detection angle. Fluorescence intensity increases up to two times at the edges of the spectral dip. Partial photobleaching of fluorescence was observed. Photonic origin of the observed effects is discussed.

Altered Circadian Timing System-Mediated Non-Dipping Pattern of Blood Pressure and Associated Cardiovascular Disorders in Metabolic and Kidney Diseases

PubMed Central

Nishiyama, Akira

2018-01-01

The morning surge in blood pressure (BP) coincides with increased cardiovascular (CV) events. This strongly suggests that an altered circadian rhythm of BP plays a crucial role in the development of CV disease (CVD). A disrupted circadian rhythm of BP, such as the non-dipping type of hypertension (i.e., absence of nocturnal BP decline), is frequently observed in metabolic disorders and chronic kidney disease (CKD). The circadian timing system, controlled by the central clock in the suprachiasmatic nucleus of the hypothalamus and/or by peripheral clocks in the heart, vasculature, and kidneys, modulates the 24 h oscillation of BP. However, little information is available regarding the molecular and cellular mechanisms of an altered circadian timing system-mediated disrupted dipping pattern of BP in metabolic disorders and CKD that can lead to the development of CV events. A more thorough understanding of this pathogenesis could provide novel therapeutic strategies for the management of CVD. This short review will address our and others’ recent findings on the molecular mechanisms that may affect the dipping pattern of BP in metabolic dysfunction and kidney disease and its association with CV disorders. PMID:29385702

Analysis and elimination method of the effects of cables on LVRT testing for offshore wind turbines

NASA Astrophysics Data System (ADS)

Jiang, Zimin; Liu, Xiaohao; Li, Changgang; Liu, Yutian

2018-02-01

The current state, characteristics and necessity of the low voltage ride through (LVRT) on-site testing for grid-connected offshore wind turbines are introduced firstly. Then the effects of submarine cables on the LVRT testing are analysed based on the equivalent circuit of the testing system. A scheme for eliminating the effects of cables on the proposed LVRT testing method is presented. The specified voltage dips are guaranteed to be in compliance with the testing standards by adjusting the ratio between the current limiting impedance and short circuit impedance according to the steady voltage relationship derived from the equivalent circuit. Finally, simulation results demonstrate that the voltage dips at the high voltage side of wind turbine transformer satisfy the requirements of testing standards.

Multiple detuned-resonator induced transparencies in MIM plasmonic waveguide

NASA Astrophysics Data System (ADS)

Liu, Li; Xia, Sheng-Xuan; Luo, Xin; Zhai, Xiang; Yu, Ya-Bin; Wang, Ling-Ling

2018-07-01

We propose a simple plasmonic waveguide system based on two-detuned resonators, which demonstrates multiple detuned-resonator induced transparencies at visible and near-infrared region. The performance of electromagnetic responses can be agile manipulated by tuning the asymmetry degree of the structure and the width of the split gap. Three transmission dips exist with the symmetrical design while three peaks emerge between the dip-position of the transmission spectra with two detuned resonators. The physical mechanism behind the plasmon-induced transparency (PIT) resonance is revealed as being attributed to the constructive interference between the confined modes in the detuned resonators. The former tend to the role of two coupled radiative oscillators. The work may open up avenues for the control of light in highly integrated optical circuits.

Multi-Temporal Analysis of Landsat Imagery for Bathymetry.

DTIC Science & Technology

1983-05-01

this data set, typical results obtained when these data were used to implement proposed procedures, an interpretation of these analyses, and based...warping, etc.) have been carried out * as described in section 3.4 and the DIPS operator manuals . For each date * the best available parameter...1982. 5. Digital Image Processing System User’s Manual DBA Systems, Inc., Under Contract DMA800-78-C-0101, 8 November 1979. 6. Naylor, L.D. Status of

Continentward-dipping detachment fault system and asymmetric rift structure of the Baiyun Sag, northern South China Sea

NASA Astrophysics Data System (ADS)

Zhou, Zhichao; Mei, Lianfu; Liu, Jun; Zheng, Jinyun; Chen, Liang; Hao, Shihao

2018-02-01

The rift architecture and deep crustal structure of the distal margin at the mid-northern margin of the South China Sea have been previously investigated by using deep seismic reflection profiles. However, one fundamental recurring problem in the debate is the extensional fault system and rift structure of the hyperextended rift basins (Baiyun Sag and Liwan Sag) within the distal margin because of the limited amount of seismic data. Based on new 3D seismic survey data and 2D seismic reflection profiles, we observe an array of fault blocks in the Baiyun Sag, which were tilted towards the ocean by extensional faulting. The extensional faults consistently dip towards the continent. Beneath the tilted fault blocks and extensional faults, a low-angle, high-amplitude and continuous reflection has been interpreted as the master detachment surface that controls the extension process. During rifting, the continentward-dipping normal faults evolved in a sequence from south to north, generating the asymmetric rift structure of the Baiyun Sag. The Baiyun Sag is separated from the oceanic domain by a series of structural highs that were uplifted by magmatic activity in response to the continental breakup at 33 Ma and a ridge jump to the south at 26-24 Ma. Therefore, we propose that magmatism played a significant role in the continental extension and final breakup in the South China Sea.

Polymer-Based Nanofibers Impregnated with Drug Infused Plant Virus Particles as a Responsive Fabric for Therapeutic Delivery

NASA Astrophysics Data System (ADS)

Honarbakhsh, Sara

A biodegradable and controlled drug delivery system has been developed herein composed of electrospun polymeric nanofibers impregnated with cargo loaded Red clover necrotic mosaic virus (RCNMV)---a robust plant virus---as the drug carrier nanoparticle. In this system, controlled drug release is achieved by altering the porosity of the biodegradable matrix as well as controlling the position and distribution of the cargo loaded nanocarriers in the matrix. Solution electrospinning as well as dipping method are used to create and to impregnate the matrix (the fibers of which possess uniformly distributed nano-size surface pores) with cargo loaded nanocarriers. Prior to the impregnation stage of cargo loaded nanocarriers into the matrix, compatibility of a group of candidate cargos (Ampicillin, Novanthrone, Doxorubicin and Ethidium Bromide) and RCNMV functionality with potential electrospinning solvents were investigated and a solvent with the least degradative effect was selected. In order to achieve both sustained and immediate drug release profiles, cargo loaded nanocarriers were embedded into the matrix---through co-spinning process---as well as on the surface of matrix fibers---through dipping method. SEM, TEM and Fluorescent Light Microscopy images of the medicated structures suggested that the nanocarriers were incorporated into/on the matrix. In vitro release assays were also carried out the results of which confirmed having obtained sustained release in the co-spun medicated structures where as dipped samples showed an immediate release profile.

Wavelength-Scanning SPR Imaging Sensors Based on an Acousto-Optic Tunable Filter and a White Light Laser

PubMed Central

Zeng, Youjun; Wang, Lei; Wu, Shu-Yuen; He, Jianan; Qu, Junle; Li, Xuejin; Ho, Ho-Pui; Gu, Dayong; Gao, Bruce Zhi; Shao, Yonghong

2017-01-01

A fast surface plasmon resonance (SPR) imaging biosensor system based on wavelength interrogation using an acousto-optic tunable filter (AOTF) and a white light laser is presented. The system combines the merits of a wide-dynamic detection range and high sensitivity offered by the spectral approach with multiplexed high-throughput data collection and a two-dimensional (2D) biosensor array. The key feature is the use of AOTF to realize wavelength scan from a white laser source and thus to achieve fast tracking of the SPR dip movement caused by target molecules binding to the sensor surface. Experimental results show that the system is capable of completing a SPR dip measurement within 0.35 s. To the best of our knowledge, this is the fastest time ever reported in the literature for imaging spectral interrogation. Based on a spectral window with a width of approximately 100 nm, a dynamic detection range and resolution of 4.63 × 10−2 refractive index unit (RIU) and 1.27 × 10−6 RIU achieved in a 2D-array sensor is reported here. The spectral SPR imaging sensor scheme has the capability of performing fast high-throughput detection of biomolecular interactions from 2D sensor arrays. The design has no mechanical moving parts, thus making the scheme completely solid-state. PMID:28067766

Structure of the inositol-1-phosphate cytidylyltransferase from Thermotoga maritima.

PubMed

Kurnasov, Oleg V; Luk, Hung-Jie Daniel; Roberts, Mary F; Stec, Boguslaw

2013-09-01

The unique steps in the synthesis of an unusual osmolyte in hyperthermophiles, di-myo-inositol-1,1'-phosphate (DIP), involve the production of CDP-inositol and its condensation with an inositol-1-phosphate molecule to form phosphorylated DIP. While many organisms fuse both activities into a single enzyme, the two are separate in Thermotoga maritima. The crystal structure of the T. maritima inositol-1-phosphate cytidylyltransferase, which as a soluble protein may transiently associate with its membrane-embedded partner phospho-DIP synthase (P-DIPS), has now been obtained. The structure shows a conserved motif of sugar nucleotide transferases (COG1213) with a structurally reinforced C-terminal Cys bonded to the core of the protein. A bound arsenosugar identifies the location of the active site for inositol 1-phosphate. Based on homologous structures from several species and the identification of the crucial conserved aspartate residue, a catalytic mechanism for this enzyme is proposed as well as a mode for its association with P-DIPS. This structure imposes constraints on the mode of association, communication and temperature activation of two separate enzymes in T. maritima. For the first time, a working model for the membrane-bound P-DIPS unit has been constructed. This sheds light on the functioning of the phosphatidylserine and phosphatidylinositol synthases involved in many physiological processes that are homologous to P-DIPS. This work provides fresh insights into the synthesis of the unusual thermoprotective compound DIP in hyperthermophiles.

Development of a Model System for Tick-Borne Flavivirus Persistence in HEK 293T Cells

PubMed Central

Mlera, Luwanika; Offerdahl, Danielle K.; Martens, Craig; Porcella, Stephen F.; Melik, Wessam

2015-01-01

ABSTRACT We devised a model system to study persistent infection by the tick-borne flavivirus Langat virus (LGTV) in 293T cells. Infection with a molecularly cloned LGTV strain produced an acute lytic crisis that left few surviving cells. The culture was repopulated by cells that were ~90% positive for LGTV E protein, thus initiating a persistent infection that was maintained for at least 35 weeks without additional lytic crises. Staining of cells for viral proteins and ultrastructural analysis revealed only minor differences from the acute phase of infection. Infectious LGTV decreased markedly over the study period, but the number of viral genomes remained relatively constant, suggesting the development of defective interfering particles (DIPs). Viral genome changes were investigated by RNA deep sequencing. At the initiation of persistent infection, levels of DIPs were below the limit of detection at a coverage depth of 11,288-fold, implying that DIPs are not required for initiation of persistence. However, after 15 passages, DIPs constituted approximately 34% of the total LGTV population (coverage of 1,293-fold). Furthermore, at this point, one specific DIP population predominated in which nucleotides 1058 to 2881 had been deleted. This defective genome specified an intact polyprotein that coded for a truncated fusion protein containing 28 N-terminal residues of E and 134 C-terminal residues of NS1. Such a fusion protein has not previously been described, and a possible function in persistent infection is uncertain. DIPs are not required for the initiation of persistent LGTV infection but may play a role in the maintenance of viral persistence. PMID:26045539

KIC 8462852 optical dipping event

NASA Astrophysics Data System (ADS)

Waagen, Elizabeth O.

2017-05-01

T. Boyajian (Louisiana State University) et al. reported in ATel #10405 that an optical dip is underway in KIC 8462852 (Boyajian's Star, Tabby's Star) beginning on 2017 May 18 UT. Tentative signs of small dips had been seen beginning April 24, and enhanced monitoring had begun at once at Fairborn Observatory (Tennessee State University). Photometry and spectroscopy from there on May 18 and 19 UT showed a dip underway. Cousins V photometry showed a drop of 0.02 magnitude, the largest dip (and the first clear one) seen in more than a year of monitoring. AAVSO observer Bruce Gary (GBL, Hereford, AZ) carried out V photometry which showed a fading from 11.906 V ± 0.004 to 11.9244 V ± 0.0033 between UT 2017 May 14 and May 19, a drop of 1.7%. Swift/UVOT observations obtained May 18 15:19 did not show a statistically significant drop in v, but Gary's photometry is given more weight. r'-band observations from Las Cumbres Observatory obtained 2017 May 17 to May 19 showed a 2% dip. Spectra by I. Steele (Liverpool JMU) et al. taken on 2017 May 20 with the 2.0 meter Liverpool Telescope, La Palma, showed no differences in the source compared to a reference spectrum taken 2016 July 4 when the system was not undergoing a dip (ATel #10406).Dips typically last for a few days, and larger dips can last over a week. It is not clear that this dip is over. Precision time-series V photometry is urgently requested from AAVSO observers, although all photometry is welcome. Finder charts with sequence may be created using the AAVSO Variable Star Plotter (https://www.aavso.org/vsp). See full Alert Notice for more details. KIC 8462852 was the subject of AAVSO Alert Notices 532 and 542. See also Boyajian et al. 2016, also available as a preprint (http://arxiv.org/abs/1509.03622). General information about KIC 8462852 may be found at http://www.wherestheflux.com/.

Simulation of dissolved nutrient export from the Dongjiang river basin with a grid-based NEWS model

NASA Astrophysics Data System (ADS)

Rong, Qiangqiang; Su, Meirong; Yang, Zhifeng; Cai, Yanpeng; Yue, Wencong; Dang, Zhi

2018-06-01

In this research, a grid-based NEWS model was proposed through coupling the geographic information system (GIS) with the Global NEWS model framework. The model was then applied to the Dongjiang River basin to simulate the dissolved nutrient export from this area. The model results showed that the total amounts of the dissolved nitrogen and phosphorus exported from the Dongjiang River basin were approximately 27154.87 and 1389.33 t, respectively. 90 % of the two loads were inorganic forms (i.e. dissolved inorganic nitrogen and phosphorus, DIN and DIP). Also, the nutrient export loads did not evenly distributed in the basin. The main stream watershed of the Dongjiang River basin has the largest DIN and DIP export loads, while the largest dissolved organic nitrogen and phosphorus (DON and DOP) loads were observed in the middle and upper stream watersheds of the basin, respectively. As for the nutrient exported from each subbasin, different sources had different influences on the output of each nutrient form. For the DIN load in each subbasin, fertilization application, atmospheric deposition and biological fixation were the three main contributors, while eluviation was the most important source for DON. In terms of DIP load, fertilizer application and breeding wastewater were the main contributors, while eluviation and fertilizer application were the two main sources for DOP.

Small Stirling dynamic isotope power system for multihundred-watt robotic missions

NASA Technical Reports Server (NTRS)

Bents, David J.

1991-01-01

Free Piston Stirling Engine (FPSE) and linear alternator (LA) technology is combined with radioisotope heat sources to produce a compact dynamic isotope power system (DIPS) suitable for multihundred watt space application which appears competitive with advance radioisotope thermoelectric generators (RTGs). The small Stirling DIPS is scalable to multihundred watt power levels or lower. The FPSE/LA is a high efficiency convertor in sizes ranging from tens of kilowatts down to only a few watts. At multihundred watt unit size, the FPSE can be directly integrated with the General Purpose Heat Source (GPHS) via radiative coupling; the resulting dynamic isotope power system has a size and weight that compares favorably with the advanced modular (Mod) RTG, but requires less than a third the amount of isotope fuel. Thus the FPSE extends the high efficiency advantage of dynamic systems into a power range never previously considered competitive for DIPS. This results in lower fuel cost and reduced radiological hazard per delivered electrical watt.

Small Stirling dynamic isotope power system for multihundred-watt robotic missions

NASA Technical Reports Server (NTRS)

Bents, David J.

1991-01-01

Free piston Stirling Engine (FPSE) and linear alternator (LA) technology is combined with radioisotope heat sources to produce a compact dynamic isotope power system (DIPS) suitable for multihundred watt space application which appears competitive with advanced radioisotope thermoelectric generators (RTGs). The small Stirling DIPS is scalable to multihundred watt power levels or lower. The FPSE/LA is a high efficiency convertor in sizes ranging from tens of kilowatts down to only a few watts. At multihundred watt unit size, the FPSE can be directly integrated with the General Purpose Heat Source (GPHS) via radiative coupling; the resulting dynamic isotope power system has a size and weight that compares favorably with the advanced modular (Mod) RTG, but requires less than a third the amount of isotope fuel. Thus the FPSE extends the high efficiency advantage of dynamic systems into a power range never previously considered competitive for DIPS. This results in lower fuel cost and reduced radiological hazard per delivered electrical watt.

New SW Pacific tectonic model: Cyclical intraoceanic magmatic arc construction and near-coeval emplacement along the Australia-Pacific margin in the Cenozoic

NASA Astrophysics Data System (ADS)

Whattam, Scott A.; Malpas, John; Ali, Jason R.; Smith, Ian E. M.

2008-03-01

Various reconstructions of the SW Pacific for the Late Cretaceous and Cenozoic suggest that northeast dipping subduction began in the South Loyalty Basin (SLB) at 55-50 Ma and that subsequent closure of the SLB resulted in the diachronous emplacement of Cretaceous-Paleocene ophiolitic nappes onto the Norfolk Ridge in New Caledonia at 40-34 Ma and in Northland, New Zealand, around 24-21 Ma. A fundamental problem with these models is that they do not account for the fact that NE dipping subduction had already been established offshore Papua New Guinea by at least 65-60 Ma which resulted in the emplacement of the Papuan Ultramafic Belt (PUB) ophiolite at 59-58 Ma. A second issue is that the reconstructions are based largely upon unfounded assumptions as to the age and nature of the basement beneath the Loyalty arc and Three Kings Ridge. Finally, reconstructions of the Northland region are based upon the erroneous assumption that the age of the majority of the igneous component comprising the Northland allochthon is Late Cretaceous-Paleocene, when in fact it is Oligocene. A new model is presented whereby the PUB, New Caledonia, and Northland ophiolites formed and were emplaced in a cyclical fashion above an extensive NE dipping Cenozoic intraoceanic arc system which diachronously propagated (N-S) along the entire eastern margin of the Australian Plate. These "infant arc" ophiolites represent fragments of suprasubduction zone lithosphere (SSZL) generated in the earliest stages of magmatic arc formation that were emplaced shortly after (<20 m.y.) as a result of forearc-Australian Plate collision. Subduction inception was the result of subsidence of older MORB-like lithosphere generated within an extensive "back arc basin" to the east of the Norfolk Ridge during the earliest stages of SLB formation above a southwest dipping Pacific Plate. During emplacement of each ophiolite, a crustal fragment of the older lithosphere was scraped off the NE dipping slab and subsequently back-thrust beneath each ophiolite during its emplacement.

Comparison of piracetam measured with HPLC-DAD, HPLC-ESI-MS, DIP-APCI-MS, and a newly developed and optimized DIP-ESI-MS.

PubMed

Lenzen, Claudia; Winterfeld, Gottfried A; Schmitz, Oliver J

2016-06-01

The direct inlet probe-electrospray ionization (DIP-ESI) presented here was based on the direct inlet probe-atmospheric pressure chemical ionization (DIP-APCI) developed by our group. It was coupled to an ion trap mass spectrometer (MS) for the detection of more polar compounds such as degradation products from pharmaceuticals. First, the position of the ESI tip, the gas and solvent flow rates, as well as the gas temperature were optimized with the help of the statistic program Minitab® 17 and a caffeine standard. The ability to perform quantitative analyses was also tested by using different concentrations of caffeine and camphor. Calibration curves with a quadratic calibration regression of R (2) = 0.9997 and 0.9998 for caffeine and camphor, respectively, were obtained. The limit of detection of 2.5 and 1.7 ng per injection for caffeine and camphor were determined, respectively. Furthermore, a solution of piracetam was used to compare established analytical methods for this drug and its impurities such as HPLC-diode array detector (DAD) and HPLC-ESI-MS with the DIP-APCI and the developed DIP-ESI. With HPLC-DAD and 10 μg piracetam on column, no impurity could be detected. With HPLC-ESI-MS, two impurities (A and B) were identified with only 4.6 μg piracetam on column, while with DIP-ESI, an amount of 1.6 μg piracetam was sufficient. In the case of the DIP-ESI measurements, all detected impurities could be identified by MS/MS studies. Graphical Abstract Scheme of the DIP-ESI principle.

The Brain as a Distributed Intelligent Processing System: An EEG Study

PubMed Central

da Rocha, Armando Freitas; Rocha, Fábio Theoto; Massad, Eduardo

2011-01-01

Background Various neuroimaging studies, both structural and functional, have provided support for the proposal that a distributed brain network is likely to be the neural basis of intelligence. The theory of Distributed Intelligent Processing Systems (DIPS), first developed in the field of Artificial Intelligence, was proposed to adequately model distributed neural intelligent processing. In addition, the neural efficiency hypothesis suggests that individuals with higher intelligence display more focused cortical activation during cognitive performance, resulting in lower total brain activation when compared with individuals who have lower intelligence. This may be understood as a property of the DIPS. Methodology and Principal Findings In our study, a new EEG brain mapping technique, based on the neural efficiency hypothesis and the notion of the brain as a Distributed Intelligence Processing System, was used to investigate the correlations between IQ evaluated with WAIS (Whechsler Adult Intelligence Scale) and WISC (Wechsler Intelligence Scale for Children), and the brain activity associated with visual and verbal processing, in order to test the validity of a distributed neural basis for intelligence. Conclusion The present results support these claims and the neural efficiency hypothesis. PMID:21423657

High resolution t-LiDAR scanning of an active bedrock fault scarp for palaeostress analysis

NASA Astrophysics Data System (ADS)

Reicherter, Klaus; Wiatr, Thomas; Papanikolaou, Ioannis; Fernández-Steeger, Tomas

2013-04-01

Palaeostress analysis of an active bedrock normal fault scarp based on kinematic indicators is carried applying terrestrial laser scanning (t-LiDAR or TLS). For this purpose three key elements are necessary for a defined region on the fault plane: (i) the orientation of the fault plane, (ii) the orientation of the slickenside lineation or other kinematic indicators and (iii) the sense of motion of the hanging wall. We present a workflow to obtain palaeostress data from point cloud data using terrestrial laser scanning. The entire case-study was performed on a continuous limestone bedrock normal fault scarp on the island of Crete, Greece, at four different locations along the WNW-ESE striking Spili fault. At each location we collected data with a mobile terrestrial light detection and ranging system and validated the calculated three-dimensional palaeostress results by comparison with the conventional palaeostress method with compass at three of the locations. Numerous kinematics indicators for normal faulting were discovered on the fault plane surface using t-LiDAR data and traditional methods, like Riedel shears, extensional break-outs, polished corrugations and many more. However, the kinematic indicators are more or less unidirectional and almost pure dip-slip. No oblique reactivations have been observed. But, towards the tips of the fault, inclination of the striation tends to point towards the centre of the fault. When comparing all reconstructed palaeostress data obtained from t-LiDAR to that obtained through manual compass measurements, the degree of fault plane orientation divergence is around ±005/03 for dip direction and dip. The degree of slickenside lineation variation is around ±003/03 for dip direction and dip. Therefore, the percentage threshold error of the individual vector angle at the different investigation site is lower than 3 % for the dip direction and dip for planes, and lower than 6 % for strike. The maximum mean variation of the complete calculated palaeostress tensors is ±005/03. So, technically t-LiDAR measurements are in the error range of conventional compass measurements. The advantages is that remote palaeostress analysis is possible. Further steps in our research will be studying reactivated faults planes with multiple kinematic indicators or striations with t-LiDAR.

Dip-Coating Process Engineering and Performance Optimization for Three-State Electrochromic Devices

NASA Astrophysics Data System (ADS)

Wu, Lu; Yang, Dejiang; Fei, Lixun; Huang, Yue; Wu, Fang; Sun, Yiling; Shi, Jiayuan; Xiang, Yong

2017-06-01

Titanium dioxide (TiO2) nanoparticles were modified onto fluorine-doped tin oxide (FTO) via dip-coating technique with different nanoparticle sizes, lifting speeds, precursor concentrations, and dipping numbers. Electrodeposition-based electrochromic device with reversible three-state optical transformation (transparent, mirror, and black) was fabricated subsequently by sandwiching a suitable amount of gel electrolyte between modified FTO electrode and flat FTO electrode. Correlation between dip-coating process engineering, morphological features of TiO2 thin films, i.e., thickness and roughness, as well as performance of electrochromic devices, i.e., optical contrast, switching time, and cycling stability, were investigated. The modified device exhibits high optical contrast of 57%, the short coloration/bleaching switching time of 6 and 20 s, and excellent cycling stability after 1500 cycles of only 27% decrement rate by adjusting dip-coating processes engineering. The results in this study will provide valuable guidance for rational design of the electrochromic device with satisfactory performance.

Characteristics, stratigraphic architecture, and time framework of multi-order mixed siliciclastic and carbonate depositional sequences, outcropping Cisco Group (Late Pennsylvanian and Early Permian), Eastern Shelf, north-central Texas, USA

NASA Astrophysics Data System (ADS)

Yang, Wan; Kominz, Michelle A.

2003-01-01

The Cisco Group on the Eastern Shelf of the Midland Basin is composed of fluvial, deltaic, shelf, shelf-margin, and slope-to-basin carbonate and siliciclastic rocks. Sedimentologic and stratigraphic analyses of 181 meter-to-decimeter-scale depositional sequences exposed in the up-dip shelf indicated that the siliciclastic and carbonate parasequences in the transgressive systems tracts (TST) are thin and upward deepening, whereas those in highstand systems tracts (HST) are thick and upward shallowing. The sequences can be subdivided into five types on the basis of principal lithofacies, and exhibit variable magnitude of facies shift corresponding to variable extents of marine transgression and regression on the shelf. The sequence stacking patterns and their regional persistence suggest a three-level sequence hierarchy controlled by eustasy, whereas local and regional changes in lithology, thickness, and sequence type, magnitude, and absence were controlled by interplay of eustasy, differential shelf subsidence, depositional topography, and pattern of siliciclastic supply. The outcropping Cisco Group is highly incomplete with an estimated 6-11% stratigraphic completeness. The average duration of deposition of the major (third-order) sequences is estimated as 67-102 ka on the up-dip shelf and increases down dip, while the average duration of the major sequence boundaries (SB) is estimated as 831-1066 ka and decreases down dip. The nondepositional and erosional hiatus on the up-dip shelf was represented by lowstand deltaic systems in the basin and slope.

Voltage Sag due to Pollution Induced Flashover Across Ceramic Insulator Strings

NASA Astrophysics Data System (ADS)

Reddy B, Subba; Goswami, Arup Kumar

2017-11-01

Voltage sag or voltage dips are significant to industrial reliability. There is a necessity to characterize the feeder level power quality (PQ) and the PQ performance among various utility companies. Contamination/pollution induced flashover is the ultimate consequence of the creeping discharges across the insulator strings which induce voltage sag. These have a severe threat on the safe and reliable operation of power systems. In the present work an attempt has been made to experimentally investigate the occurrence of voltage sag/dips during pollution induced flashovers. Results show significant dip/sag in the voltage magnitude during the flashover process.

A Comparison of Optical versus Hardware Fourier Transforms.

DTIC Science & Technology

1983-10-31

AD- R136 223 A COMPRISON’OF OPTICAL ERSUS HARDWARE FOURIER i/i.TRANSFORMS(U) VIRGINIA POLYTECHNIC INST AND STATE UNIV BLACKSBURG DEPT OF PHYSICS S P...transform and its inverse filtered Fourier transform obtained with the Digital Image Processing (DIP) hardware system located at the School of Aerospace...transparencies, and provided to us by Dr. Ralph G. Allen, Director of the Laser Effects Branch (Division of Radiation Sciences). The DIP system consisted of: an

Nature of the high-binding-energy dip in the low-temperature photoemission spectra of Bi2Sr2CaCu2O8+δ

NASA Astrophysics Data System (ADS)

Dessau, D. S.; Shen, Z.-X.; Wells, B. O.; King, D. M.; Spicer, W. E.; Arko, A. J.; Lombardo, L. W.; Mitzi, D. B.; Kapitulnik, A.

1992-03-01

At the transition to superconductivity, an anomalous high-binding-energy (~=-90 meV) dip appears in the low-temperature photoemission spectra taken along the Γ-M¯ high-symmetry direction of Bi2Sr2CaCu2O8+δ. This paper details experiments which further characterize the energy and k-space dependence of this dip structure. The dip occurs over a wide portion of the Γ-M¯ zone diagonal (110), yet shows minimal energy dispersion. In the spectra taken along the Γ-X zone edge (100), the dip is very weak or not present. We show that these results imply that the dip is not an artifact dependent on the experiment or special features of the band structure and therefore is an intrinsic feature of the superconducting state of Bi2Sr2CaCu2O8+δ. The behavior of the normal-state bands along Γ-M¯ in relation to the local-density-approximation prediction of a Bi-O-based electron ``pocket'' is also discussed, with our data explained most naturally if the Bi-O band remains above the Fermi level for all k.

Folding associated with extensional faulting: Sheep Range detachment, southern Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guth, P.L.

1985-01-01

The Sheep Range detachment is a major Miocene extensional fault system of the Great Basin. Its major faults have a scoop shape, with straight, N-S traces extending 15-30 km and then abruptly turning to strike E-W. Tertiary deformation involved simultaneous normal faulting, sedimentation, landsliding, and strike-slip faulting. Folds occur in two settings: landslide blocks and drag along major faults. Folds occur in landslide blocks and beneath them. Most folds within landslide blocks are tight anticlines, with limbs dipping 40-60 degrees. Brecciation of the folds and landslide blocks suggests brittle deformation. Near Quijinump Canyon in the Sheep Range, at least threemore » landslide blocks (up to 500 by 1500 m) slid into a small Tertiary basin. Tertiary limestone beneath the Paleozoic blocks was isoclinally folded. Westward dips reveal drag folds along major normal faults, as regional dips are consistently to the east. The Chowderhead anticline is the largest drag fold, along an extensional fault that offsets Ordovician units 8 km. East-dipping Ordovician and Silurian rocks in the Desert Range form the hanging wall. East-dipping Cambrian and Ordovician units in the East Desert Range form the foot wall and east limb of the anticline. Caught along the fault plane, the anticline's west-dipping west limb contains mostly Cambrian units.« less

Optical polarimetry of KIC 8462852 in 2017 May-August

NASA Astrophysics Data System (ADS)

Steele, I. A.; Copperwheat, C. M.; Jermak, H. E.; Kennedy, G. M.; Lamb, G. P.

2018-01-01

We present optical polarimetry in the period of 2017 May-August of the enigmatic `dipping' star KIC 8462852. During that period, three ˜1 per cent photometric dips were reported by other observers. We measured the average absolute polarization of the source, and find no excess or unusual polarization compared to a nearby comparison star. We place tight upper limits on any change in the degree of polarization of the source between epochs in-dip and out-of-dip of <0.1 per cent (8500 Å) and <0.2 per cent (7050 Å and 5300 Å). How our limits are interpreted depends on the specific model being considered. If the whole stellar disc were covered by material with an optical depth of ˜0.01, then the fractional polarization introduced by this material must be less than 10-20 per cent. While our non-detection does not constrain the comet scenario, it predicts that even modest amounts of dust that have properties similar to Solar system comets may be detectable. We note that the sensitivity of our method scales with the depth of the dip. Should a future ˜20 per cent photometric dip be observed (as was previously detected by Kepler), our method would constrain any induced polarization associated with any occulting material to 0.5-1.0 per cent.

Gender-Based Differential Item Performance in Mathematics Achievement Items.

ERIC Educational Resources Information Center

Doolittle, Allen E.; Cleary, T. Anne

1987-01-01

Eight randomly equivalent samples of high school seniors were each given a unique form of the ACT Assessment Mathematics Usage Test (ACTM). Signed measures of differential item performance (DIP) were obtained for each item in the eight ACTM forms. DIP estimates were analyzed and a significant item category effect was found. (Author/LMO)

Mahalanobis Distance-Based Classifiers are Able to Recognize EEG Patterns by Using Few EEG Electrodes

DTIC Science & Technology

2001-10-25

Mouriño 3 , Angela Cattini 4 , Serenella Salinari 4 , Maria Grazia Marciani 2,5 and Febo Cincotti 5 1 Dip. Fisiologia umana e Farmacologia...Performing Organization Name(s) and Address(es) Dip. Fisiologia umana e Farmacologia, Università "La Sapienza", Rome, ITALY Performing Organization

Long-term efficacy of wood dip-treated with multicomponent biocides

Treesearch

Carol A. Clausen; Vina W. Yang

2005-01-01

Biocides designed for prevention of indoor mold growth on wood-based materials need to provide long-term protection under conditions of high humidity. Specimens of kiln-dried southern pine and unseasoned southern pine, aspen, and Douglas-fir were dip-treated with borate-dimethylcocoamine (DMCA) supplemented with voriconazole, thiabendazole, or thujaplicin and evaluated...

Polysaccharide based edible coating on sapota fruit

NASA Astrophysics Data System (ADS)

Menezes, Joslin; Athmaselvi, K. A.

2016-10-01

Sapota fruits are highly perishable and have short shelf life at the ambient conditions. The edible coatings have been used on different agricultural products in order to extend their post harvest life. In the present study, the polysaccharide based edible coating made up of sodium alginate and pectin (2%) was studied on the shelf life of sapota fruits. The coating of the fruits is done by dipping method with two dipping time (2 and 4 min). The both control and coated sapota fruits were stored at refrigerated temperature (4±1°C). The physico-chemical analysis including acidity, total soluble solids, ascorbic acid, pH, weight loss, colour and firmness were measured on 1, 8, 15, 23 and 30th day of storage. There was significant difference (p≤0.05) in these physico-chemical parameters between control and coated sapota fruits with 2 and 4 min dipping time. The sensory analysis of control and coated sapota fruits showed that, the polysaccharide coating with 2 minutes dipping time was effective in maintaining the organoleptic properties of the fruits.

Optical fiber tip interferometer gas pressure sensor based on anti-resonant reflecting guidance mechanism

NASA Astrophysics Data System (ADS)

Yang, Y. B.; Wang, D. N.; Xu, Ben; Wang, Z. K.

2018-05-01

We propose and demonstrate a gas pressure sensor based on an anti-resonant reflecting guidance (ARRG) mechanism in quartz capillary tube with an open cavity. The device is simple in fabrication by only fusion splicing a segment of capillary tube with single mode fiber. It has compact size, robust structure, convenient mode of operation, and high sensitivity of 4.278 nm/MPa. Moreover, as two Faby-Perot cavities exist in the device, which create the interference spectrum with several distinct resonance dips, a simultaneous gas pressure and temperature detection can be readily achieved by tracing two dip wavelengths. The error in the measurement due to the choice of different resonant dips can be effectively reduced by using the Fourier band pass filtering method.

Reexamination of the subsurface fault structure in the vicinity of the 1989 moment-magnitude-6.9 Loma Prieta earthquake, central California, using steep-reflection, earthquake, and magnetic data

USGS Publications Warehouse

Zhang, Edward; Fuis, Gary S.; Catchings, Rufus D.; Scheirer, Daniel S.; Goldman, Mark; Bauer, Klaus

2018-06-13

We reexamine the geometry of the causative fault structure of the 1989 moment-magnitude-6.9 Loma Prieta earthquake in central California, using seismic-reflection, earthquake-hypocenter, and magnetic data. Our study is prompted by recent interpretations of a two-part dip of the San Andreas Fault (SAF) accompanied by a flower-like structure in the Coachella Valley, in southern California. Initially, the prevailing interpretation of fault geometry in the vicinity of the Loma Prieta earthquake was that the mainshock did not rupture the SAF, but rather a secondary fault within the SAF system, because network locations of aftershocks defined neither a vertical plane nor a fault plane that projected to the surface trace of the SAF. Subsequent waveform cross-correlation and double-difference relocations of Loma Prieta aftershocks appear to have clarified the fault geometry somewhat, with steeply dipping faults in the upper crust possibly connecting to the more moderately southwest-dipping mainshock rupture in the middle crust. Examination of steep-reflection data, extracted from a 1991 seismic-refraction profile through the Loma Prieta area, reveals three robust fault-like features that agree approximately in geometry with the clusters of upper-crustal relocated aftershocks. The subsurface geometry of the San Andreas, Sargent, and Berrocal Faults can be mapped using these features and the aftershock clusters. The San Andreas and Sargent Faults appear to dip northeastward in the uppermost crust and change dip continuously toward the southwest with depth. Previous models of gravity and magnetic data on profiles through the aftershock region also define a steeply dipping SAF, with an initial northeastward dip in the uppermost crust that changes with depth. At a depth 6 to 9 km, upper-crustal faults appear to project into the moderately southwest-dipping, planar mainshock rupture. The change to a planar dipping rupture at 6–9 km is similar to fault geometry seen in the Coachella Valley.

Influence of dipping cycles on physical, optical, and electrical properties of Cu 2 NiSnS 4 : Direct solution dip coating for photovoltaic applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mokurala, Krishnaiah; Mallick, Sudhanshu; Bhargava, Parag

Direct solution coating technique has emerged as a promising economically viable process for earth abundant chalcogenide absorber materials for photovoltaic applications. Here, direct ethanol based dip coating of earth abundant Cu2NiSnS4 (CNTS) films on soda lime glass (SLG), molybdenum coated glass (Mo), and fluorine doped tin oxide coated glass (FTO) substrates is investigated. The structural and morphological properties of pre-annealed and sulfurized CNTS films coated on SLG, FTO, and Mo substrates are reported. The influence of dipping cycles on composition and optoelectronic properties of pre-annealed and sulfurized CNTS films deposited on SLG substrate is presented. Energy dispersive spectroscopy (EDS) andmore » X-ray fluorescence (XRF) analysis reveal how changes in thickness and elemental composition affect morphology and optoelectronic properties. The obtained absorption coefficient, optical bandgap, resistivity and mobility of pre - annealed and sulfurized films are found to be 104 cm-1, 1.5 eV, 0.48 Ocm, 3.4 cm2/Vs and 104 cm-1, 1.29 eV, 0.14 Ocm, 11.0 cm2/Vs, respectively. These properties are well suited for photovoltaic applications and lead to the conclusion that the direct ethanol based dip coating can be an alternative economically viable process for the fabrication of earth abundant CNTS absorber layers for thin film solar cells.« less

A CLIPS based personal computer hardware diagnostic system

NASA Technical Reports Server (NTRS)

Whitson, George M.

1991-01-01

Often the person designated to repair personal computers has little or no knowledge of how to repair a computer. Described here is a simple expert system to aid these inexperienced repair people. The first component of the system leads the repair person through a number of simple system checks such as making sure that all cables are tight and that the dip switches are set correctly. The second component of the system assists the repair person in evaluating error codes generated by the computer. The final component of the system applies a large knowledge base to attempt to identify the component of the personal computer that is malfunctioning. We have implemented and tested our design with a full system to diagnose problems for an IBM compatible system based on the 8088 chip. In our tests, the inexperienced repair people found the system very useful in diagnosing hardware problems.

Dipping fossil fabrics of continental mantle lithosphere as tectonic heritage of oceanic paleosubductions

NASA Astrophysics Data System (ADS)

Babuska, Vladislav; Plomerova, Jaroslava; Vecsey, Ludek; Munzarova, Helena

2016-04-01

Subduction and orogenesis require a strong mantle layer (Burov, Tectonophys. 2010) and our findings confirm the leading role of the mantle lithosphere. We have examined seismic anisotropy of Archean, Proterozoic and Phanerozoic provinces of Europe by means of shear-wave splitting and P-wave travel-time deviations of teleseismic waves observed at dense arrays of seismic stations (e.g., Vecsey et al., Tectonophys. 2007). Lateral variations of seismic-velocity anisotropy delimit domains of the mantle lithosphere, each of them having its own consistent fabric. The domains, modeled in 3D by olivine aggregates with dipping lineation a, or foliation (a,c), represent microplates or their fragments that preserved their pre-assembly fossil fabrics. Evaluating seismic anisotropy in 3D, as well as mapping boundaries of the domains helps to decipher processes of the lithosphere formation. Systematically dipping mantle fabrics and other seismological findings seem to support a model of continental lithosphere built from systems of paleosubductions of plates of ancient oceanic lithosphere (Babuska and Plomerova, AGU Geoph. Monograph 1989), or from stacking of the plates (Helmstaedt and Schulze, Geol. Soc. Spec. Publ. 1989). Seismic anisotropy in the oceanic mantle lithosphere, explained mainly by the olivine A- or D-type fabric (Karato et al., Annu. Rev. Earth Planet. Sci. 2008), was discovered a half century ago (Hess, Nature 1964). Field observations and laboratory experiments indicate the oceanic olivine fabric might be preserved in the subducting lithosphere to a depth of at least 200-300 km. We thus interpret the dipping anisotropic fabrics in domains of the European mantle lithosphere as systems of "frozen" paleosubductions (Babuska and Plomerova, PEPI 2006) and the lithosphere base as a boundary between the fossil anisotropy in the lithospheric mantle and an underlying seismic anisotropy related to present-day flow in the asthenosphere (Plomerova and Babuska, Lithos 2010).

Evaluation of the diving reflex in response to nonterminal submersion of White Pekin ducks in water-based foam.

PubMed

Caputo, M P; Alphin, R L; Pritchett, E; Hougentogler, D P; Johnson, A L; Benson, E R; Patil, C

2013-02-01

The mass depopulation of production birds remains an effective means of controlling fast-moving, highly infectious diseases such as avian influenza and virulent Newcastle disease. Water-based fire-fighting foam is a conditionally approved method of depopulating floor-reared gallinaceous poultry such as chickens and turkeys; however, ducks have physiological mechanisms that may make them more resistant to this method of depopulation. The following experiment was designed to assess the physiological responses of White Pekin ducks to nonterminal submersion in water-based foam compared with water. The hypothesis of this experiment was that submersion of ducks in water or water-based foam would trigger the diving reflex and lead to bradycardia. All treatments led to pronounced bradycardia. Heart rate was not significantly different between treatments during the final 30 s of the 60-s treatment period. Heart rate dropped significantly faster for the water dip and foam dip treatments and rose significantly faster than the foam pour treatment after the termination of the 60-s treatment period. Duration of bradycardia approached significance for the foam pour treatment, leading to a longer duration of bradycardia compared with the water pour, water dip, and foam dip treatments. The results of this experiment demonstrated that apnea and bradycardia as a result of the diving reflex can occur as a result of submersion in foam, which may have an impact on the time it takes White Pekin ducks to reach unconsciousness and death during water-based foam depopulation.

From the Cover: Potentiation of Drug-Induced Phospholipidosis In Vitro through PEGlyated Graphene Oxide as the Nanocarrier.

PubMed

Yang, Liecheng; Zhong, Xiaoyan; Li, Qian; Zhang, Xihui; Wang, Yangyun; Yang, Kai; Zhang, Leshuai W

2017-03-01

Cationic amphiphilic drugs (CADs) are small molecules that can induce phospholipidosis (PLD), causing the intracellular accumulation of phospholipid in the lamellar bodies. Nanotechnology based drug delivery systems have been used widely, while it is unknown if drug-induced PLD (DIP) can be potentiated through drug retention by indigestible nanocarriers. Due to the high drug loading capacity of graphene, we investigated if PEGylated graphene oxide (PEG-GO) loaded with CAD could potentiate DIP. Tamoxifen induced the accumulation of NBD-PE, a fluorescence labeled phospholipid in human hepatoma HepG2 cells, while PEG-GO loaded with tamoxifen (PEG-GO/tamoxifen) further potentiated PLD. PEG-GO/tamoxifen induced more gene expression of PLD marker than tamoxifen alone. PEG-GO enhanced DIP was also observed for other CAD, indicating that nanocarrier potentiated DIP could be universal. More lamellar bodies were observed in PEG-GO/tamoxifen treated cells than tamoxifen alone by transmission electron microscopy. When compared with tamoxifen alone, PEG-GO/tamoxifen showed a delayed but potent PLD. In addition, the retarded PLD recovery by PEG-GO/tamoxifen indicated that the reversibility of DIP was interfered. Confocal microscopy revealed the increased number of lysosomes, greater expression of lysosomal associated membrane protein 2 (LAMP2) (a PLD marker), and an increase in the co-localization between lysosome/LAMP2 and NBD-PE by PEG-GO/tamoxifen rather than tamoxifen alone. Finally, we found that PEG-GO or/and tamoxifen-induced PLD seemed to have no correlation with autophagy. This research suggests pharmaceutical companies and regulatory agencies that if nanoparticles are used as the vectors for drug delivery, the adverse drug effects may be further potentiated probably through the long-term accumulation of nanocarriers. © The Author 2016. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Impact of the slab dip change onto the deformation partitioning in the northern Lesser Antilles oblique subduction zone (Antigua-Virgin Islands)

NASA Astrophysics Data System (ADS)

Laurencin, Muriel; Marcaillou, Boris; Klingelhoefer, Frauke; Graindorge, David; Lebrun, Jean-Frédéric; Laigle, Mireille; Lallemand, Serge

2017-04-01

Marine geophysical cruises Antithesis (2013-2016) investigate the impact of the variations in interplate geometry onto margin tectonic deformation along the strongly oblique Lesser Antilles subduction zone. A striking features of this margin is the drastic increase in earthquake number from the quiet Barbuda-St Martin segment to the Virgin Islands platform. Wide-angle seismic data highlight a northward shallowing of the downgoing plate: in a 150 km distance from the deformation front, the slab dipping angle in the convergence direction decreases from 12° offshore of Antigua Island to 7° offshore of Virgin Islands. North-South wide-angle seismic line substantiates a drastic slab-dip change that likely causes this northward shallowing. This dip change is located beneath the southern tip of the Virgin Islands platform where the Anegada Passage entails the upper plate. Based on deep seismic lines and bathymetric data, the Anegada Passage is a 450 km long W-E trending set of pull-apart basins and strike-slip faults that extends from the Lesser Antilles accretionary prism to Puerto Rico. The newly observed sedimentary architecture within pull-apart Sombrero and Malliwana basins indicates a polyphased tectonic history. A past prominent NW-SE extensive to transtensive phase, possibly related to the Bahamas Bank collision, opened the Anegada Passage as previously published. Transpressive tectonic evidences indicate that these structures have been recently reactivated in an en-echelon sinistral strike-slip system. The interpreted strain ellipsoid is consistent with deformation partitioning. We propose that the slab northward shallowing increases the interplate coupling and the seismic activity beneath the Virgin Islands platform comparatively to the quiet Barbuda-St Martin segment. It is noteworthy that the major tectonic partitioning structure in the Lesser Antilles forearc is located above the slab dip change where the interplate seismic coupling increases.

Understanding Differential Item Performance as a Consequence of Gender Differences in Academic Background.

ERIC Educational Resources Information Center

Doolittle, Allen E.

Differential item performance (DIP) is discussed as a concept that does not necessarily imply item bias or unfairness to subgroups of examinees. With curriculum-based achievement tests, DIP is presented as a valid reflection of group differences in requisite skills and instruction. Using data from a national testing of the ACT Assessment, this…

Magnetic fabric study of rock deformation during alpine tectonic evolution on a cross section through the Eastern Alps (Austria)

NASA Astrophysics Data System (ADS)

Gruber, K.; Scholger, R.; Pueyo, E. L.

2010-05-01

Measurements of anisotropy of magnetic susceptibility (AMS) were carried out on samples from more than seventy sites collected in the Eastern Alps. The sites were taken alongside a North-South transect (about 15°30` East Longitude) from Scheibbs in the North to Kapfenberg in the South, comprising most of the Northern Calcareous Alps (NCA) nappes, Helvetic and Penninic Flysh units as well as the greywacke zone. Samples were taken in detail mostly in Mesozoic rocks of the NCA, from North to South: Bajuvaric (Frankenfels, Lunz, Sulzbach and Reisalpen nappes), Tirolic (Ötscher, Göller, Rotwald-Gindelstein nappes) and Juvavic (Mürzalpen nappe) system. Two to six sites per thrust sheet or nappe were analysed for a structural investigation of the relationship between magnetic fabric and tectonic strain. Standard paleomagnetic drill cores were taken. All measurements were performed in the Petrophysics and Paleomagnetic laboratories of the University of Leoben using AGICO MFK1-Kappabridge susceptibility system and a 2-G cryogenic magnetometer. Statistical evaluation of the AMS data was perfomed using the software package AGICO ANISOFT 4.2. (Chadima et al., 2009). Throughout the Eastern Alps transect distinct changes of the magnetic fabric are observed. Primary sedimentary fabrics and very low susceptibility values are dominant in most cases in the northernmost and southernmost part of the transect. Some inverse fabrics were found in few sites of the nappes and the percentage increases towards the south which might be related to tectonic events. Contrastingly, isotropic fabrics dominate in the middle part. The Helvetic and Penninic Flysh units yield in general weak oblate fabrics. A few sites show a tendency to inverse fabrics which indicate the presence of a certain amount of strain within this unit. The oblate fabrics of the Helvetic and Flysh units show either shallow NE dipping or slightly steeper SW dipping k1-axis orientation. Within the inverse fabrics, even steeper NE or SW dipping k1-axis are present. In a previous paleomagnetic study of the same samples (Pueyo et al., 2002) both, primary and secondary remanent magnetization vectors were observed. No significant rotations were detected in the Flysh units. All samples from the Bajuvaric system show dominantly very low susceptibility values and isotropic fabrics and were therefore excluded from further investigations. Bajuvaric nappes hardly show any significant rotations based on paleomagnetic data (Pueyo et al., 2002). The nappes of the Tirolic and Juvavic systems have very low susceptibility values but they increase slightly towards the south. The shape of the anisotropy ellipsoid remains oblate (group A) in most cases and the degree of anisotropy is very weak. Also more prolate fabrics (group B) are present. Group A and B show a trend to shallow N or S dipping k1-axis in the North. Further in the south the k1-axis of group A tend to dip steeply NE. Shallow NE or SW dipping and slightly steeper NE or SW dipping oriented prolate susceptibility ellipsoids are dominant in group B. Tirolic and Juvavic units display clockwise rotation ranging between 30 and more than 100° (Pueyo et al., 2002), which was assigned to block rotation. Shallow E dipping and NNW dipping oblate susceptibility ellipsoids are dominant in the Basement. A general increase of the degree of rotation (Pueyo et al., 2002) as well as better defined susceptibility ellipsoids with mainly oblate fabrics towards the south can be observed. Six Tertiary deviatoric paleostress tensor groups are described by Peresson & Decker (1997). The new AMS data will be presented and correlated to the young tectonic history of the Eastern Alps. The study was funded by the Austrian Academy of Sciences (ÖAW) in the frame of the Geophysics of the Earths Crust Programme. Peresson, H. and Decker, K., 1997. The Tertiary dynamics of the northern Eastern Alps (Austria): Changing palaeostresses in a collisional plate boundary, Tectonophysics, 272, 125 - 157. Pueyo, E.L., Schneider, M., Mauritsch, H.J., Scholger, R., Lein, R., 2002. A paleomagnetic cross section through the Eastern Northern Calcareous Alps: preliminary data in the Mariazell meridian. Pangeo poster.

The role of parents, friends and teachers in adolescents' cigarette smoking and tombak dipping in Sudan.

PubMed

El-Amin, Salma El-Tayeb; Nwaru, Bright I; Ginawi, Ibrahim; Pisani, Paola; Hakama, Matti

2011-03-01

To assess the influence of smoking and tombak (local smokeless tobacco) dipping by parents, teachers and friends on cigarette smoking and tombak dipping by school-going Sudanese adolescents. This was a school-based cross-sectional survey was conducted in 2005-2006. Logistic regression was used for the analysis. A total of 4277 Sudanese school-going adolescents (aged 11-17 years) from 23 schools who completed an anonymous self-administered questionnaire on the use of tobacco products. Main outcome measures were self-reported tobacco use during the previous month defined current tobacco use. Ever smoking, tombak dipping and other tobacco products were also considered as outcomes. After adjusting for sex, age and school grade, adolescents' smoking habits were strongly associated with the habit in their parents and friends and, more weakly, with tombak dipping by teachers. When adjusted for each other, the association with smoking in friends was unaffected and remained significant (prevalence OR (POR) of having ever smoked was 1.94, 95% CI 1.64 to 2.29; OR of being current smoker was 3.77, 95% CI 2.80 to 5.07). Tobacco smoking in friends was positively associated with adolescents ever tombak dipping (POR 1.81, 95% CI 1.41 to 2.33) and current dipping (OR 3.33, 95% CI 2.20 to 5.05). The association with parental habits was reduced but still significantly elevated. Tombak dipping by teachers was only associated with adolescents ever tobacco smoking. Tobacco use by parents, teachers and friends was associated with adolescents' tobacco habits. The influence of friends was the strongest. In developing programmes against adolescents' tobacco habits, there is need to target the influence of these 'significant others'. Sudan needs to develop and implement comprehensive anti-smoking and anti-tombak dipping legislation to reduce the growing prevalence of such habits.

Systematic vertical and lateral changes in quality and time resolution of the macrofossil record: insights from Holocene transgressive deposits, Po coastal plain, Italy

NASA Astrophysics Data System (ADS)

Azzarone, Michele; Scarponi, Daniele; Kusnerik, Kristopher; Amorosi, Alessandro; Bohacs, Kevin M.; Drexler, Tina M.; Kowalewski, Michał

2017-04-01

In siliciclastic marine settings, skeletal concentrations are a characteristic feature of transgressive intervals that provide insights into paleobiology and sequence stratigraphy. To investigate taphonomic signatures of transgressive intervals, we analyzed three cores from a Holocene depositional profile of the Po coastal plain, in northern Italy. Coupled multivariate taphonomic and bathymetric trends delineate spatial and temporal gradients in sediment starvation/bypassing, suggesting that quality and resolution of the fossil record vary predictably along the studied depositional profile. Moreover, joint consideration of taphonomic, bathymetric, and fossil density trends across the study area reveals distinctive signatures that are useful in characterizing facies associations and recognizing surfaces and intervals of sequence stratigraphic significance. Within the southern Po plain succession, taphonomic degradation of macroskeletal remains increases from proximal—nearshore to distal—offshore locations. This trend is discernible for both biologically-driven (bioerosion) and chemically/physically-driven (e.g., dissolution, abrasion) shell alterations. Compared to the up-dip (most proximal) core, the down-dip core is distinguished by shell-rich lithosomes affected by ecological condensation (co-occurrence of environmentally non-overlapping taxa) and by higher taphonomic alteration. The onshore-offshore taphonomic trend likely reflects variation in sediment-supply along the depositional profile of the Holocene Northern Adriatic shelf, with surface/near-surface residence-time of macroskeletal remains increasing down dip due to lower accumulation rates. These results indicate that, during transgressive phases, changes in sea-level (base level) are likely to produce down-dip taphonomic gradients across shelves, where the quality and resolution of the fossil record both deteriorate distally. The amino acid radiometrically calibrated dates on bivalves and the chronostratigraphic framework for this profile suggest that the high levels of taphonomic degradation observed distally developed over millennial time scales ( 8ky). The patterns documented here may be characteristic of siliciclastic-dominated depositional systems that experience high-frequency, base-level fluctuations.

The regional structural setting of the 2008 Wells earthquake and Town Creek Flat Basin: implications for the Wells earthquake fault and adjacent structures

USGS Publications Warehouse

Henry, Christopher S.; Colgan, Joseph P.

2011-01-01

The 2008 Wells earthquake occurred on a northeast-striking, southeast-dipping fault that is clearly delineated by the aftershock swarm to a depth of 10-12 km below sea level. However, Cenozoic rocks and structures around Wells primarily record east-west extension along north- to north-northeast-striking, west-dipping normal faults that formed during the middle Miocene. These faults are responsible for the strong eastward tilt of most basins and ranges in the area, including the Town Creek Flat basin (the location of the earthquake) and the adjacent Snake Mountains and western Windermere Hills. These older west-dipping faults are locally overprinted by a younger generation of east-dipping, high-angle normal faults that formed as early as the late Miocene and have remained active into the Quaternary. The most prominent of these east-dipping faults is the set of en-échelon, north-striking faults that bounds the east sides of the Ruby Mountains, East Humboldt Range, and Clover Hill (about 5 km southwest of Wells). The northeastern-most of these faults, the Clover Hill fault, projects northward along strike toward the Snake Mountains and the approximately located surface projection of the Wells earthquake fault as defined by aftershock locations. The Clover Hill fault also projects toward a previously unrecognized, east-facing Quaternary fault scarp and line of springs that appear to mark a significant east-dipping normal fault along the western edge of Town Creek Flat. Both western and eastern projections may be northern continuations of the Clover Hill fault. The Wells earthquake occurred along this east-dipping fault system. Two possible alternatives to rupture of a northern continuation of the Clover Hill fault are that the earthquake fault (1) is antithetic to an active west-dipping fault or (2) reactivated a Mesozoic thrust fault that dips east as a result of tilting by the west-dipping faults along the west side of the Snake Mountains. Both alternatives are precluded by the depths of the earthquake and aftershocks, about 8 km and as deep as 12 km, respectively. These depths are below where an antithetic fault would intersect any main fault, and a tilted, formerly shallow and sub-horizontal thrust fault would not extend to depths of more than about 5–6 km. The east-dipping, high-angle, earthquake fault cuts older west-dipping faults rather than reactivating them, highlighting a change in the structural style of Basin and Range extension in this region from closely-spaced, west-dipping faults that rotated significantly during slip and accommodated large-magnitude extension, to widely-spaced, high-angle faults that accommodate much less total strain over a long time span.

Isotopic Evidence for the Source and Fate of Phosphorus in Everglades Wetland Ecosystems

NASA Technical Reports Server (NTRS)

Li, Xin; Wang, Yang; Stern, Jennifer; Gu, Binhe

2011-01-01

Phosphorus has historically been a limiting nutrient in the Florida Everglades. Increased P loading to the Everglades over the past several decades has led to significant changes in water quality and plant communities. Stormwater runoff that drains agricultural lands and enters the Water Conservation Areas (WCAs) are known to contain elevated levels of P, but the exact source of this P has not been fully determined. Here the results of an O isotope study of dissolved inorganic phosphate (DIP) in both polluted and relatively pristine (or reference) areas of the Everglades are reported. The data reveal spatial and temporal variations in the delta 18O signature of DIP, reflecting the source and the degree of cycling of P. The delta 18O values of DIP collected from the Everglades National Park were close or equal to the predicted delta 18O values of DIP formed in situ in equilibrium with ambient water, indicating that P is quickly cycled in the water column in oligotrophic ecosystems with very low P concentrations. However, most DIP samples collected from areas impacted by agricultural runoff yielded delta 18O values that deviated from the predicted equilibrium DIP delta 18O values based on the delta 18O of water and water temperature, suggesting that biological cycling of P was not rapid enough to remove the fertilizer ?18O signature in the DIP pool from areas receiving high P loading. The delta 18O signature of DIP in impacted areas reflects a mixing of fertilizer P and biologically cycled P, where the relative proportions of biologically cycled vs. fertilizer DIP are controlled by both biological (microbial activities and plant uptake) and hydrologic factors (loading rate and residence time). Using a two-end-member (i.e., fertilizer P and biologically cycled P) mixing model, fertilizers were estimated to contribute about 15 100% of the DIP pool in the highly impacted areas of the northern Everglades, whereas the DIP pool in the reference (i.e., relatively pristine) wetlands in the Everglades National Park was dominated by biologically cycled P. The study shows that O isotopic measurements of dissolved PO(exp 3-, sub 4) can be a useful tool for tracing the fertilizer P inputs to freshwater ecosystems.

Age related prevalence of hand osteoarthritis diagnosed by photography (HOASCORE).

PubMed

Jonsson, Helgi

2017-12-02

Hand photography has been used in a number of studies to determine the presence and severity of hand osteoarthritis (HOA). The aim of this study was to present age and gender specific prevalences of HOA diagnosed by this method. Six thousand three hundred forty three photographs (from 3676 females and 2667 males aged 40-96) were scored for hand osteoarthritis by a 0-3 grade (0 = no evidence of OA, 1 = possible OA, 2 = definite OA and 3 = severe OA) for each of the three main sites, distal interphalangeal joints (DIP), proximal interphalangeal joints (PIP) and thumb base (CMC1). An aggregate score of 0-9 was thus obtained (HOASCORE) to reflect the severity of HOA in each case. DIP joints were most commonly affected, followed by the thumb base and the PIP joints. Having definite DIP joint OA starts at a younger age compared with the other two sites, and there is a marked female preponderance in the age groups from 55 to 69, but after 70 the gender differences are less marked and the prevalence is fairly stable. PIP joint prevalence also indicates a female preponderance from 60 to 79. Thumb base OA has a more marked female preponderance and a rising prevalence thoughout life. The prevalence of individuals with no evidence of photographic OA (HOASCORE = 0) drops from 88% to 57% between the age categories 40-49 and 50-54 and decreased to 33% in the 70-74 age group with a slower decline after that age. DIP and PIP prevalence were strongly associated with each other with an OR of 16.6(12.8-21.5),p < 0.001 of having definite OA at the other site. This was less marked for the thumb base with an OR of 2.2(1.8-2.7, p < 0.001), and 2.7(2.0-3.5, p < 0.001) of having definite DIP or PIP HOA respectively. The prevalence of hand OA in DIP, PIP and thumb base joints obtained by the photographic HOASCORE method is higher in women and increases after the age of fifty. These results are in line with those obtained by clinical examination and radiography. The advantage of the method lies in easy applicability and low cost.

Fault and joint geometry at Raft River Geothermal Area, Idaho

NASA Astrophysics Data System (ADS)

Guth, L. R.; Bruhn, R. L.; Beck, S. L.

1981-07-01

Raft River geothermal reservoir is formed by fractures in sedimentary strata of the Miocene and Pliocene salt lake formation. The fracturing is most intense at the base of the salt lake formation, along a decollement that dips eastward at less than 50 on top of metamorphosed precambrian and lower paleozoic rocks. Core taken from less than 200 m above the decollement contains two sets of normal faults. The major set of faults dips between 500 and 700. These faults occur as conjugate pairs that are bisected by vertical extension fractures. The second set of faults dips 100 to 200 and may parallel part of the basal decollement or reflect the presence of listric normal faults in the upper plate. Surface joints form two suborthogonal sets that dip vertically. East-northeast-striking joints are most frequent on the limbs of the Jim Sage anticline, a large fold that is associated with the geothermal field.

Holographic enhanced remote sensing system

NASA Technical Reports Server (NTRS)

Iavecchia, Helene P.; Gaynor, Edwin S.; Huff, Lloyd; Rhodes, William T.; Rothenheber, Edward H.

1990-01-01

The Holographic Enhanced Remote Sensing System (HERSS) consists of three primary subsystems: (1) an Image Acquisition System (IAS); (2) a Digital Image Processing System (DIPS); and (3) a Holographic Generation System (HGS) which multiply exposes a thermoplastic recording medium with sequential 2-D depth slices that are displayed on a Spatial Light Modulator (SLM). Full-parallax holograms were successfully generated by superimposing SLM images onto the thermoplastic and photopolymer. An improved HGS configuration utilizes the phase conjugate recording configuration, the 3-SLM-stacking technique, and the photopolymer. The holographic volume size is currently limited to the physical size of the SLM. A larger-format SLM is necessary to meet the desired 6 inch holographic volume. A photopolymer with an increased photospeed is required to ultimately meet a display update rate of less than 30 seconds. It is projected that the latter two technology developments will occur in the near future. While the IAS and DIPS subsystems were unable to meet NASA goals, an alternative technology is now available to perform the IAS/DIPS functions. Specifically, a laser range scanner can be utilized to build the HGS numerical database of the objects at the remote work site.

Initiation of a Low-Angle Normal Fault Active Across the Upper Brittle-Plastic Transition, Chemehuevi Mountains, CA

NASA Astrophysics Data System (ADS)

LaForge, J.; John, B. E.; Grimes, C. B.; Stunitz, H.; Heilbronner, R.

2016-12-01

The Chemehuevi detachment fault system, part of the regionally developed Colorado River extensional corridor, hosts exceptional exposures of a denuded fault system related to Miocene extension. Here, we characterize the early history of extension associated with a small slip (1-2 km) low-angle normal fault, the Mohave Wash fault (MWF), initially active across the brittle-plastic transition. Strain localized in three principal ways across the 23-km down-dip exposure (T <150° to >400°C): a brittle fault zone, localized, disseminated quartz mylonites, and syntectonic dikes hosting mylonitic fabrics. Brittle deformation in these crystalline rocks was concentrated into a 10-62-m thick brittle fault zone hosting localized, unmineralized to chlorite-epidote-quartz mineralized zones of cataclasite series fault rocks ≤3 m thick and rare pseudotachylite. Mylonitic deformation played an increased role in deformation down dip (NE), with mylonites increasing in quantity and average thickness. At shallow structural levels, footwall mylonites are absent; at 9-18 km down dip, cm-scale quartz mylonites are common; ≥18 km down dip, meter-scale syntectonic intermediate-felsic dikes are mylonitic, are attenuated into parallelism with the MWF, and host well-developed L-S fabric; 23 km down dip, the footwall hosts meter-thick zones of disseminated mylonitic quartz of varying intensities. These mylonites host microstructures that record progressively higher deformation temperature down dip, with dislocation-creep in quartz indicative of T of 280-400°C to ≥500°C, and diffusion creep with grain boundary sliding in dikes suggestive of even higher T deformation. Dike emplacement in the system is syntectonic with MWF slip; mafic-intermediate composition dikes intruded damage zone fractures and cataclasites, and were in turn fractured; Pb/U zircon ages of intermediate-felsic dikes range from ca. 1.5 ± 1 Ma to 3.8 ± 1 Ma after the onset of regional extension, but predate rapid slip. Cross cutting relations and absolute dating suggest the early history of the MWF evolved in two distinct phases: 1) seismogenic rupture with contemporaneous localized footwall mylonitization, followed by 2) additional cataclasis, episodic localized and magmatism, mylonitization and fluid-flow.

Visible tunable lighting system based on polymer composites embedding ZnO and metallic clusters: from colloids to thin films.

PubMed

Truong, Thai Giang; Dierre, Benjamin; Grasset, Fabien; Saito, Noriko; Saito, Norio; Nguyen, Thi Kim Ngan; Takahashi, Kohsei; Uchikoshi, Tetsuo; Amela-Cortes, Marian; Molard, Yann; Cordier, Stéphane; Ohashi, Naoki

2016-01-01

The development of phosphor devices free of heavy metal or rare earth elements is an important issue for environmental reasons and energy efficiency. Different mixtures of ZnO nanocrystals with Cs 2 Mo 6 I 8 (OOC 2 F 5 ) 6 cluster compound (CMIF) dispersed into polyvinylpyrrolidone matrix have been prepared by very simple and low cost solution chemistry. The resulting solutions have been used to fabricate highly transparent and luminescent films by dip coating free of heavy metal or rare earth elements. The luminescence properties of solution and dip-coated films were investigated. The luminescence of such a system is strongly dependent on the ratios between ZnO and CMIF amounts, the excitation wavelength and the nature of the system. By varying these two parameters (ratio and wavelength), a large variety of colors, from blue to red as well as white, can be achieved. In addition, differences in the luminescence properties have been observed between solutions and thin films as well as changes of CMIF emission band maximum wavelength. This may suggest some possible interactions between the different luminophore centers, such as energy transfer or ligands exchange on the Mo 6 clusters.

Visible tunable lighting system based on polymer composites embedding ZnO and metallic clusters: from colloids to thin films

PubMed Central

Truong, Thai Giang; Dierre, Benjamin; Grasset, Fabien; Saito, Noriko; Saito, Norio; Nguyen, Thi Kim Ngan; Takahashi, Kohsei; Uchikoshi, Tetsuo; Amela-Cortes, Marian; Molard, Yann; Cordier, Stéphane; Ohashi, Naoki

2016-01-01

Abstract The development of phosphor devices free of heavy metal or rare earth elements is an important issue for environmental reasons and energy efficiency. Different mixtures of ZnO nanocrystals with Cs2Mo6I8(OOC2F5)6 cluster compound (CMIF) dispersed into polyvinylpyrrolidone matrix have been prepared by very simple and low cost solution chemistry. The resulting solutions have been used to fabricate highly transparent and luminescent films by dip coating free of heavy metal or rare earth elements. The luminescence properties of solution and dip-coated films were investigated. The luminescence of such a system is strongly dependent on the ratios between ZnO and CMIF amounts, the excitation wavelength and the nature of the system. By varying these two parameters (ratio and wavelength), a large variety of colors, from blue to red as well as white, can be achieved. In addition, differences in the luminescence properties have been observed between solutions and thin films as well as changes of CMIF emission band maximum wavelength. This may suggest some possible interactions between the different luminophore centers, such as energy transfer or ligands exchange on the Mo6 clusters. PMID:27877895

Visible tunable lighting system based on polymer composites embedding ZnO and metallic clusters: from colloids to thin films

NASA Astrophysics Data System (ADS)

Truong, Thai Giang; Dierre, Benjamin; Grasset, Fabien; Saito, Noriko; Saito, Norio; Nguyen, Thi Kim Ngan; Takahashi, Kohsei; Uchikoshi, Tetsuo; Amela-Cortes, Marian; Molard, Yann; Cordier, Stéphane; Ohashi, Naoki

2016-01-01

The development of phosphor devices free of heavy metal or rare earth elements is an important issue for environmental reasons and energy efficiency. Different mixtures of ZnO nanocrystals with Cs2Mo6I8(OOC2F5)6 cluster compound (CMIF) dispersed into polyvinylpyrrolidone matrix have been prepared by very simple and low cost solution chemistry. The resulting solutions have been used to fabricate highly transparent and luminescent films by dip coating free of heavy metal or rare earth elements. The luminescence properties of solution and dip-coated films were investigated. The luminescence of such a system is strongly dependent on the ratios between ZnO and CMIF amounts, the excitation wavelength and the nature of the system. By varying these two parameters (ratio and wavelength), a large variety of colors, from blue to red as well as white, can be achieved. In addition, differences in the luminescence properties have been observed between solutions and thin films as well as changes of CMIF emission band maximum wavelength. This may suggest some possible interactions between the different luminophore centers, such as energy transfer or ligands exchange on the Mo6 clusters.

Dissolved nutrient balance and net ecosystem metabolism in a Mediterranean-climate coastal lagoon: San Diego Bay

NASA Astrophysics Data System (ADS)

Delgadillo-Hinojosa, F.; Zirino, A.; Holm-Hansen, O.; Hernández-Ayón, J. M.; Boyd, T. J.; Chadwick, B.; Rivera-Duarte, I.

2008-02-01

The temporal and spatial variability of dissolved inorganic phosphate (DIP), nitrogen (DIN), carbon (DIC) and dissolved organic carbon (DOC) were studied in order to determine the net ecosystem metabolism (NEM) of San Diego Bay (SDB), a Mediterranean-climate lagoon. A series of four sampling campaigns were carried out during the rainy (January 2000) and the dry (August 2000 and May and September 2001) seasons. During the dry season, temperature, salinity and DIP, DIC and DOC concentrations increased from oceanic values in the outer bay to higher values at the innermost end of the bay. DIP, DIC and DOC concentrations showed a clear offset from conservative mixing implying production of these dissolved materials inside the bay. During the rainy season, DIP and DOC increased to the head, whereas salinity decreased toward the mouth due to land runoff and river discharges. The distributions of DIP and DOC also showed a deviation from conservative mixing in this season, implying a net addition of these dissolved materials during estuarine mixing within the bay. Mass balance calculations showed that SDB consistently exported DIP (2.8-9.8 × 10 3 mol P d -1), DIC (263-352 × 10 3 mol C d -1) and DOC (198-1233 × 10 3 mol C d -1), whereas DIN (5.5-18.2 × 10 3 mol N d -1) was exported in all samplings except in May 2001 when it was imported (8.6 × 10 3 mol N d -1). The DIP, DIC and DOC export rates along with the strong relationship between DIP, DIC or DOC and salinity suggest that intense tidal mixing plays an important role in controlling their distributions and that SDB is a source of nutrients and DOC to the Southern California Bight. Furthermore, NEM ranged from -8.1 ± 1.8 mmol C m -2 d -1 in September to -13.5 ± 5.8 mmol C m -2 d -1 in January, highlighting the heterotrophic character of SDB. In order to explain the net heterotrophy of this system, we postulate that phytoplankton-derived particulate organic matter, stimulated by upwelling processes in the adjacent coastal waters, is transported into the bay, retained and then remineralized within the system. Our results were compared with those reported for the heterotrophic hypersaline coastal lagoons located in the semi-arid coast of California-Baja California, and with those autotrophic hypersaline systems found in the semi-arid areas of Australia. We point out that the balance between autotrophy and heterotrophy in inverse estuaries is dependent on net external inputs of either inorganic nutrients or organic matter as it has been indicated for positive estuaries.

75 FR 17162 - Dipping and Coating Operations (Dip Tanks) Standard; Extension of the Office of Management and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

...] Dipping and Coating Operations (Dip Tanks) Standard; Extension of the Office of Management and Budget's... Standard on Dipping and Coating Operations (Dip Tanks) (29 CFR 1910.126(g)(4)). DATES: Comments must be... of efforts in obtaining information (29 U.S.C. 657). The Standard on Dipping and Coating Operations...

Personality traits and circadian blood pressure patterns: A seven year prospective study

PubMed Central

Terracciano, Antonio; Strait, James; Scuteri, Angelo; Meirelles, Osorio; Sutin, Angelina R.; Tarasov, Kirill; Ding, Jun; Marongiu, Michele; Orru, Marco; Pilia, Maria Grazia; Cucca, Francesco; Lakatta, Edward; Schlessinger, David

2014-01-01

Objective A nighttime dip in blood pressure is associated with decreased risk of cardiovascular morbidity and mortality. We examined whether personality traits predict nighttime dipping blood pressure. Methods A community-based sample of 2,848 adults from Sardinia (Italy) completed the Revised NEO Personality Inventory and 7.34-years later (SD=0.87) were examined with 24-hour ambulatory blood pressure monitoring. The primary analyses examined the associations of personality traits with continuous and categorical measures of mean arterial, systolic and diastolic blood pressure nighttime dipping. Results Agreeableness and conscientiousness were associated with more nocturnal blood pressure dipping (β = .05, p=.025 and β = .07, p<.001, respectively) and lower systolic blood pressure at night (β = -.045, p=.018 and β = -.032; p=.072, respectively). Non-dippers were particularly more impulsive (p=.009), less trusting (p=.004), and less self-disciplined (p=.001), but there was no significant association between nocturnal dipping blood pressure and trait anxiety (p=.78) or depression (p=.59). The associations were stronger when comparing extreme dippers (nighttime drop ≥ 20%) to reverse dippers (nighttime increase in blood pressure). Indeed, scoring 1 SD higher on conscientiousness was associated with about 40% reduced risk of reverse dipping (OR = 1.43, CI = 1.08-1.91). Conclusions We found evidence that reduced nighttime blood pressure dipping is associated with antagonism and impulsivity related traits but not with measures of emotional vulnerability. The strongest associations were found with conscientiousness, a trait that may have broad impact on cardiovascular health. PMID:24608035

Continentward-Dipping Normal Faults, Boudinage and Ductile Shear at Rifted Passive Margins

NASA Astrophysics Data System (ADS)

Clerc, C. N.; Ringenbach, J. C.; Jolivet, L.; Ballard, J. F.

2017-12-01

Deep structures resulting from the rifting of the continental crust are now well imaged by seismic profiles. We present a series of recent industrial profiles that allow the identification of various rift-related geological processes such as crustal boudinage, ductile shear of the base of the crust and low-angle detachment faulting. Along both magma-rich and magma-poor rifted margins, we observe clear indications of ductile deformation of the deep continental crust. Large-scale shallow dipping shear zones are identified with a top-to-the-continent sense of shear. This sense of shear is consistent with the activity of the Continentward-Dipping Normal Faults (CDNF) that accommodate the extension in the upper crust. This pattern is responsible for an oceanward migration of the deformation and of the associated syn-tectonic deposits (sediments and/or volcanics). We discuss the origin of the Continentward-Dipping Normal Faults (CDNF) and investigate their implications and the effect of sediment thermal blanketing on crustal rheology. In some cases, low-angle shear zones define an anastomosed pattern that delineates boudin-like structures that seem to control the position and dip of upper crustal normal faults. We present some of the most striking examples from several locations (Uruguay, West Africa, South China Sea…), and discuss their rifting histories that differ from the classical models of oceanward-dipping normal faults.

A comparison of radioisotope Brayton and Stirling system for lunar surface mobile power

NASA Astrophysics Data System (ADS)

Harty, Richard B.

1991-01-01

A study was performed by the Rocketdyne Division of Rockwell 2.5-kWe modular dynamic isotope power system (DIPS) using a Stirling power conversion system. The results of this study were compared with similar results performed under the DIPS program using a Brayton power conversion system. The study indicated that the Stirling power module has 20% lower mass and 40% lower radiator area than the Brayton module. However, the study also revealed that because the Stirling power module requires a complex heat pipe arrangment to transport heat from the isotope to the Stirling heater head and a pumped NaK heat rejection loop, the Stirling module is much more difficult to integrate with the isotope heat source and heat rejection system.

Hydrogeologic setting, ground-water flow, and ground-water quality at the Lake Wheeler Road research station, 2001-03 : North Carolina Piedmont and Mountains Resource Evaluation Program

USGS Publications Warehouse

Chapman, Melinda J.; Bolich, Richard E.; Huffman, Brad A.

2005-01-01

Results of a 2-year field study of the regolith-fractured bedrock ground-water system at the Lake Wheeler Road research station in Wake County, North Carolina, indicate both disconnection and interaction among components of the ground-water system. The three components of the ground-water system include (1) shallow, porous regolith; (2) a transition zone, including partially weathered rock, having both secondary (fractures) and primary porosity; and (3) deeper, fractured bedrock that has little, if any, primary porosity and is dominated by secondary fractures. The research station includes 15 wells (including a well transect from topographic high to low settings) completed in the three major components of the ground-water-flow system and a surface-water gaging station on an unnamed tributary. The Lake Wheeler Road research station is considered representative of a felsic gneiss hydrogeologic unit having steeply dipping foliation and a relatively thick overlying regolith. Bedrock foliation generally strikes N. 10? E. to N. 30? E. and N. 20? W. to N. 40? W. to a depth of about 400 feet and dips between 70? and 80? SE. and NE., respectively. From 400 to 600 feet, the foliation generally strikes N. 70? E. to N. 80? E., dipping 70? to 80? SE. Depth to bedrock locally ranges from about 67 to 77 feet below land surface. Fractures in the bedrock generally occur in two primary sets: low dip angle, stress relief fractures that cross cut foliation, and steeply dipping fractures parallel to foliation. Findings of this study generally support the conceptual models of ground-water flow from high to low topographic settings developed for the Piedmont and Blue Ridge Provinces in previous investigations, but are considered a refinement of the generalized conceptual model based on a detailed local-scale investigation. Ground water flows toward a surface-water boundary, and hydraulic gradients generally are downward in recharge areas and upward in discharge areas; however, local variations in vertical gradients are apparent. Water-quality sampling and monitoring efforts were conducted to characterize the interaction of components of the ground-water system. Elevated nitrate concentrations as high as 22 milligrams per liter were detected in shallow ground water from the regolith at the study site. These elevated nitrate concentrations likely are related to land use, which includes agricultural practices that involve animal feeding operations and crop fertilization. Continuous ground-water-quality data indicate seasonal fluctuations in field water-quality properties, differences with respect to depth, and fluctuations during recharge events. Water-quality properties recorded in the regolith well following rainfall indicate the upwelling of deeper ground water in the discharge area, likely from ground water in the transition-zone fractures. Additionally, interaction with a surface-water boundary appears likely in the ground-water discharge area, as water levels in all three ground-water zones, including the deep bedrock, mimic the surface-water rise during rainfall.

Structural control on the CO2 release west of Mt. Epomeo resurgent block (Ischia, Italy)

NASA Astrophysics Data System (ADS)

de Vita, S.; Marotta, E.; Ventura, G.; Chiodini, G.

2003-04-01

Volcanism at Ischia started more than 150 ka B.P. and continued until the last eruption occurred in 1302 A.D. Ischia is dominated by the caldera forming eruption of Mt. Epomeo Green Tuff (55 ka), which was followed by block resurgence inside the caldera from 33 ka B.P. Resurgence influenced the volcanic activity determining the conditions for magma ascent mainly along the eastern edge of the resurgent block. The resurgent area has a poligonal shape resulting from reactivation of regional faults and by activation of faults related to volcanotectonism. The western sector is bordered by inward dipping, high angle strike-slip/reverse faults testifying a compressional stress regime in this area. These features are cut by late outward dipping normal faults due to gravitational stress. The activity of the volcanic system is testified by seismicity and thermal manifestations. Fumarolic activity concentrates along the faults that borders westward the Mt. Epomeo resurgent block, where the Green Tuff overlies fractured lavas. The structural data show that, outside the most active degassing zone, fractures show a NNW-SSE strike and dip toward Mt. Epomeo. These fractures delimit the northern sector of Mt. Epomeo and show strike and dip consistent with the inward dipping reverse faults. Inside the degassing area fractures show a NW-SE strike and dip outward Mt. Epomeo. These gravity-related faults cut the lavas where the hydrothermal circulation is active. The dip direction of the NW-SE striking fractures within the degassing zone is not consistent with that of the strike-slip/reverse faults (i.e. towards NE) but agrees well with that of the gravity-induced faults (dip direction towards SW). Inside the degassing zone, NW-SE striking faults with lengths not exceeding the hydrothermalized extension occur. This arrangement indicate that the syn-resurgence faults act as permeability barriers, whereas the youngest faults act as the main fluid pathway.

High-sensitivity optical sensing of axial strain based on microfiber with microarched transition region

NASA Astrophysics Data System (ADS)

Xia, Liang; Xing, Zengshan; Yu, Jianhui; Lu, Huihui; Guan, Heyuan; Zhong, Yongchun; Chen, Zhe

2017-11-01

We demonstrated strain sensing of a microfiber with a microarched transition region, which was fabricated by flame heated tapering. Due to multimode interference of different propagation modes of microfiber, two main transmission dips were observed at 1215.0 and 1469.8 nm. Enhanced by the microarched transition region, the depth of the dip was up to 19 dB at 1215.0 nm. The position of the dip red-shifted while the axial strain changed from 0 to 1166.2 μɛ. The axial strain sensitivity was up to 56.6 pm/μɛ, which was one order of magnitude higher than that of the traditional optical strain sensor based on microfiber or fiber Bragg grating. The linear correlation coefficient was 98.21%. This kind of microfiber with a microarched transition region can be widely used in various physical, chemical, and biological sensing and detection fields.

Exclusion of overlapping symptoms in DSM-5 mixed features specifier: heuristic diagnostic and treatment implications.

PubMed

Malhi, Gin S; Byrow, Yulisha; Outhred, Tim; Fritz, Kristina

2017-04-01

This article focuses on the controversial decision to exclude the overlapping symptoms of distractibility, irritability, and psychomotor agitation (DIP) with the introduction of the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5) mixed features specifier. In order to understand the placement of mixed states within the current classification system, we first review the evolution of mixed states. Then, using Kraepelin's original classification of mixed states, we compare and contrast his conceptualization with modern day definitions. The DSM-5 workgroup excluded DIP symptoms, arguing that they lack the ability to differentiate between manic and depressive states; however, accumulating evidence suggests that DIP symptoms may be core features of mixed states. We suggest a return to a Kraepelinian approach to classification-with mood, ideation, and activity as key axes-and reintegration of DIP symptoms as features that are expressed across presentations. An inclusive definition of mixed states is urgently needed to resolve confusion in clinical practice and to redirect future research efforts.

A 1,574-Day Periodicity of Transits Orbiting KIC 8462852

NASA Astrophysics Data System (ADS)

Sacco, G.; Ngo, L. D.; Modolo, J.

2018-06-01

Observations of the main sequence F3V star KIC 8462852 (also known as Boyajianís star) revealed extreme aperiodic dips in flux up to 20% during the four years of the Kepler mission. Smaller dips (< 3%) were also observed with ground-based telescopes between May 2017 and May 2018. We investigated possible correlation between recent dips and the major dips in the last 100 days of the Kepler mission. We compared Kepler light curve data, 2017 data from two observatories (TFN, OGG) which are part of the Las Cumbres Observatory (LCO) network, as well as archival data from the Harvard College Observatory (HCO), Sonneberg Observatory, and Sternberg Observatory, and determined that observations appear consistent with a 1,574-day (4.31-year) periodicity of a transit (or group of transits) orbiting Boyajianís star within the habitable zone. Comparison with future observations is required to validate this hypothesis. Furthermore, it is unknown if transits that have produced other major dips as observed during the Kepler mission (e.g. D792) share the same orbital period. Nevertheless, the proposed periodicity is a step forward in guiding future observation efforts.

Genetic fine-mapping of DIPLOSPOROUS in Taraxacum (dandelion; Asteraceae) indicates a duplicated DIP-gene

PubMed Central

2010-01-01

Background DIPLOSPOROUS (DIP) is the locus for diplospory in Taraxacum, associated to unreduced female gamete formation in apomicts. Apomicts reproduce clonally through seeds, including apomeiosis, parthenogenesis, and autonomous or pseudogamous endosperm formation. In Taraxacum, diplospory results in first division restitution (FDR) nuclei, and inherits as a dominant, monogenic trait, independent from the other apomixis elements. A preliminary genetic linkage map indicated that the DIP-locus lacks suppression of recombination, which is unique among all other map-based cloning efforts of apomeiosis to date. FDR as well as apomixis as a whole are of interest in plant breeding, allowing for polyploidization and fixation of hybrid vigor, respectively. No dominant FDR or apomixis genes have yet been isolated. Here, we zoom-in to the DIP-locus by largely extending our initial mapping population, and by analyzing (local) suppression of recombination and allele sequence divergence (ASD). Results We identified 24 recombinants between two most closely linked molecular markers to DIP in an F1-population of 2227 plants that segregates for diplospory and lacks parthenogenesis. Both markers segregated c. 1:1 in the entire population, indicating a 1:1 segregation rate of diplospory. Fine-mapping showed three amplified fragment length polymorphisms (AFLPs) closest to DIP at 0.2 cM at one flank and a single AFLP at 0.4 cM at the other flank. Our data lacked strong evidence for ASD at marker regions close to DIP. An unexpected bias towards diplosporous plants among the recombinants (20 out of 24) was found. One third of these diplosporous recombinants showed incomplete penetrance of 50-85% diplospory. Conclusions Our data give interesting new insights into the structure of the diplospory locus in Taraxacum. We postulate a locus with a minimum of two DIP-genes and possibly including one or two enhancers or cis-regulatory elements on the basis of the bias towards diplosporous recombinants and incomplete penetrance of diplospory in some of them. We define the DIP-locus to 0.6 cM, which is estimated to cover ~200-300 Kb, with the closest marker at 0.2 cM. Our results confirm the minor role of suppression of recombination and ASD around DIP, making it an excellent candidate to isolate via a chromosome-walking approach. PMID:20659311

Genetic fine-mapping of DIPLOSPOROUS in Taraxacum (dandelion; Asteraceae) indicates a duplicated DIP-gene.

PubMed

Vijverberg, Kitty; Milanovic-Ivanovic, Slavica; Bakx-Schotman, Tanja; van Dijk, Peter J

2010-07-26

DIPLOSPOROUS (DIP) is the locus for diplospory in Taraxacum, associated to unreduced female gamete formation in apomicts. Apomicts reproduce clonally through seeds, including apomeiosis, parthenogenesis, and autonomous or pseudogamous endosperm formation. In Taraxacum, diplospory results in first division restitution (FDR) nuclei, and inherits as a dominant, monogenic trait, independent from the other apomixis elements. A preliminary genetic linkage map indicated that the DIP-locus lacks suppression of recombination, which is unique among all other map-based cloning efforts of apomeiosis to date. FDR as well as apomixis as a whole are of interest in plant breeding, allowing for polyploidization and fixation of hybrid vigor, respectively. No dominant FDR or apomixis genes have yet been isolated. Here, we zoom-in to the DIP-locus by largely extending our initial mapping population, and by analyzing (local) suppression of recombination and allele sequence divergence (ASD). We identified 24 recombinants between two most closely linked molecular markers to DIP in an F1-population of 2227 plants that segregates for diplospory and lacks parthenogenesis. Both markers segregated c. 1:1 in the entire population, indicating a 1:1 segregation rate of diplospory. Fine-mapping showed three amplified fragment length polymorphisms (AFLPs) closest to DIP at 0.2 cM at one flank and a single AFLP at 0.4 cM at the other flank. Our data lacked strong evidence for ASD at marker regions close to DIP. An unexpected bias towards diplosporous plants among the recombinants (20 out of 24) was found. One third of these diplosporous recombinants showed incomplete penetrance of 50-85% diplospory. Our data give interesting new insights into the structure of the diplospory locus in Taraxacum. We postulate a locus with a minimum of two DIP-genes and possibly including one or two enhancers or cis-regulatory elements on the basis of the bias towards diplosporous recombinants and incomplete penetrance of diplospory in some of them. We define the DIP-locus to 0.6 cM, which is estimated to cover approximately 200-300 Kb, with the closest marker at 0.2 cM. Our results confirm the minor role of suppression of recombination and ASD around DIP, making it an excellent candidate to isolate via a chromosome-walking approach.

78 FR 21159 - Additional Requirements for Special Dipping and Coating Operations (Dip Tanks); Extension of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-09

...] Additional Requirements for Special Dipping and Coating Operations (Dip Tanks); Extension of the Office of Management and Budget's Approval of the Information Collection (Paperwork) Requirement AGENCY: Occupational... requirement specified in its Standard on Dipping and Coating Operations (Dip Tanks) (29 CFR 1910.126(g)(4...

Slip and Dilation Tendency Analysis of the Tuscarora Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

Critically stressed fault segments have a relatively high likelihood of acting as fluid flow conduits (Sibson, 1994). As such, the tendency of a fault segment to slip (slip tendency; Ts; Morris et al., 1996) or to dilate (dilation tendency; Td; Ferrill et al., 1999) provides an indication of which faults or fault segments within a geothermal system are critically stressed and therefore likely to transmit geothermal fluids. The slip tendency of a surface is defined by the ratio of shear stress to normal stress on that surface: Ts = τ / σn (Morris et al., 1996). Dilation tendency is defined by the stress acting normal to a given surface: Td = (σ1-σn) / (σ1-σ3) (Ferrill et al., 1999). Slip and dilation were calculated using 3DStress (Southwest Research Institute). Slip and dilation tendency are both unitless ratios of the resolved stresses applied to the fault plane by ambient stress conditions. Values range from a maximum of 1, a fault plane ideally oriented to slip or dilate under ambient stress conditions to zero, a fault plane with no potential to slip or dilate. Slip and dilation tendency values were calculated for each fault in the focus study areas at, McGinness Hills, Neal Hot Springs, Patua, Salt Wells, San Emidio, and Tuscarora on fault traces. As dip is not well constrained or unknown for many faults mapped in within these we made these calculations using the dip for each fault that would yield the maximum slip tendency or dilation tendency. As such, these results should be viewed as maximum tendency of each fault to slip or dilate. The resulting along-fault and fault-to-fault variation in slip or dilation potential is a proxy for along fault and fault-to-fault variation in fluid flow conduit potential. Stress Magnitudes and directions Stress field variation within each focus area was approximated based on regional published data and the world stress database (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2010; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012; Moeck et al., 2010; Moos and Ronne, 2010 and Reinecker et al., 2005) as well as local stress information if applicable. For faults within these focus systems we applied either a normal faulting stress regime where the vertical stress (sv) is larger than the maximum horizontal stress (shmax) which is larger than the minimum horizontal stress (sv>shmax>shmin) or strike-slip faulting stress regime where the maximum horizontal stress (shmax) is larger than the vertical stress (sv) which is larger than the minimum horizontal stress (shmax >sv>shmin) depending on the general tectonic province of the system. Based on visual inspection of the limited stress magnitude data in the Great Basin we used magnitudes such that shmin/shmax = .527 and shmin/sv= .46, which are consistent with complete and partial stress field determinations from Desert Peak, Coso, the Fallon area and Dixie valley (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2011; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012). Slip and dilation tendency for the Tuscarora geothermal field was calculated based on the faults mapped Tuscarora area (Dering, 2013). The Tuscarora area lies in the Basin and Range Province, as such we applied a normal faulting stress regime to the Tuscarora area faults, with a minimum horizontal stress direction oriented 115, based on inspection of local and regional stress determinations, as explained above. Under these stress conditions north-northeast striking, steeply dipping fault segments have the highest dilation tendency, while north-northeast striking 60° dipping fault segments have the highest tendency to slip. Tuscarora is defined by a left-step in a major north- to-north northeast striking, west-dipping range-bounding normal fault system. Faults within the broad step define an anticlinal accommodation zone...

Improving health service delivery for women with diabetes in pregnancy in remote Australia: survey of care in the Northern Territory Diabetes in Pregnancy Partnership.

PubMed

Edwards, Laura; Connors, Christine; Whitbread, Cherie; Brown, Alex; Oats, Jeremy; Maple-Brown, Louise

2014-12-01

In the Northern Territory (NT), 38% of 3500 births each year are to Indigenous women, 80% of whom live in regional and remote areas. Compared with the general Australian population, rates of pre-existing type 2 diabetes in pregnancy are 10-fold higher and rates of gestational diabetes are 1.5-fold higher among Indigenous women. Current practices in screening for diabetes in pregnancy in remote Australia are not known. To assess current health service delivery for NT women with diabetes in pregnancy (DIP) by surveying healthcare professionals' views and practices in DIP screening and management. A cross-sectional survey of NT healthcare professionals providing clinical care for women with DIP was conducted based on pre-identified themes of communication, care-coordination, education, orientation and guidelines, logistics and access, and information technology. Of the 116 responders to the survey, 78% were primary healthcare professionals, 32% midwives and 25% general practitioners. High staff turnover was evident: of Central Australian professionals, only 33% (urban) and 18% (regional/remote) had been in their current position over 5 years. DIP screening was conducted at first antenatal visit by 66% and at 24-28-week gestation by 81%. Only 50% of respondents agreed that most women at their health service received appropriate care for DIP, and 41% of primary care practitioners were neutral or not confident in their skills to manage DIP. It is promising that many healthcare professionals report following new guidelines in conducting early pregnancy screening for DIP in high risk women. Several challenges were identified in healthcare delivery to a high risk population in remote Australia. © 2014 The Royal Australian and New Zealand College of Obstetricians and Gynaecologists.

Influence of fracture anisotropy on ground water ages and chemistry, Valley and Ridge province, Pennsylvania

USGS Publications Warehouse

Burton, W.C.; Plummer, Niel; Busenberg, E.; Lindsey, B.D.; Gburek, W.J.

2002-01-01

Model ground water ages based on chlorofluorocarbons (CFCs) and tritium/helium-3 (3H/3He) data were obtained from two arrays of nested piezometers located on the north limb of an anticline in fractured sedimentary rocks in the Valley and Ridge geologic province of Pennsylvania. The fracture geometry of the gently east plunging fold is very regular and consists predominately of south dipping to subhorizontal to north dipping bedding-plane parting and east striking, steeply dipping axial-plane spaced cleavage. In the area of the piezometer arrays, which trend north-south on the north limb of the fold, north dipping bedding-plane parting is a more dominant fracture set than is steeply south dipping axial-plane cleavage. The dating of ground water from the piezometer arrays reveals that ground water traveling along paths parallel to the dip direction of bedding-plane parting has younger 3H/3He and CFC model ages, or a greater component of young water, than does ground water traveling along paths opposite to the dip direction. In predominantly unmixed samples there is a strong positive correlation between age of the young fraction of water and dissolved sodium concentration. The travel times inferred from the model ages are significantly longer than those previously calculated by a ground water flow model, which assumed isotropically fractured layers parallel to topography. A revised model factors in the directional anisotropy to produce longer travel times. Ground water travel times in the watershed therefore appear to be more influenced by anisotropic fracture geometry than previously realized. This could have significant implications for ground water models in other areas underlain by similarly tilted or folded sedimentary rock, such as elsewhere in the Valley and Ridge or the early Mesozoic basins.

"Dip-and-read" paper-based analytical devices using distance-based detection with color screening.

PubMed

Yamada, Kentaro; Citterio, Daniel; Henry, Charles S

2018-05-15

An improved paper-based analytical device (PAD) using color screening to enhance device performance is described. Current detection methods for PADs relying on the distance-based signalling motif can be slow due to the assay time being limited by capillary flow rates that wick fluid through the detection zone. For traditional distance-based detection motifs, analysis can take up to 45 min for a channel length of 5 cm. By using a color screening method, quantification with a distance-based PAD can be achieved in minutes through a "dip-and-read" approach. A colorimetric indicator line deposited onto a paper substrate using inkjet-printing undergoes a concentration-dependent colorimetric response for a given analyte. This color intensity-based response has been converted to a distance-based signal by overlaying a color filter with a continuous color intensity gradient matching the color of the developed indicator line. As a proof-of-concept, Ni quantification in welding fume was performed as a model assay. The results of multiple independent user testing gave mean absolute percentage error and average relative standard deviations of 10.5% and 11.2% respectively, which were an improvement over analysis based on simple visual color comparison with a read guide (12.2%, 14.9%). In addition to the analytical performance comparison, an interference study and a shelf life investigation were performed to further demonstrate practical utility. The developed system demonstrates an alternative detection approach for distance-based PADs enabling fast (∼10 min), quantitative, and straightforward assays.

Mapping three-dimensional geological features from remotely-sensed images and digital elevation models

NASA Astrophysics Data System (ADS)

Morris, Kevin Peter

Accurate mapping of geological structures is important in numerous applications, ranging from mineral exploration through to hydrogeological modelling. Remotely sensed data can provide synoptic views of study areas enabling mapping of geological units within the area. Structural information may be derived from such data using standard manual photo-geologic interpretation techniques, although these are often inaccurate and incomplete. The aim of this thesis is, therefore, to compile a suite of automated and interactive computer-based analysis routines, designed to help a the user map geological structure. These are examined and integrated in the context of an expert system. The data used in this study include Digital Elevation Model (DEM) and Airborne Thematic Mapper images, both with a spatial resolution of 5m, for a 5 x 5 km area surrounding Llyn Cow lyd, Snowdonia, North Wales. The geology of this area comprises folded and faulted Ordo vician sediments intruded throughout by dolerite sills, providing a stringent test for the automated and semi-automated procedures. The DEM is used to highlight geomorphological features which may represent surface expressions of the sub-surface geology. The DEM is created from digitized contours, for which kriging is found to provide the best interpolation routine, based on a number of quantitative measures. Lambertian shading and the creation of slope and change of slope datasets are shown to provide the most successful enhancement of DEMs, in terms of highlighting a range of key geomorphological features. The digital image data are used to identify rock outcrops as well as lithologically controlled features in the land cover. To this end, a series of standard spectral enhancements of the images is examined. In this respect, the least correlated 3 band composite and a principal component composite are shown to give the best visual discrimination of geological and vegetation cover types. Automatic edge detection (followed by line thinning and extraction) and manual interpretation techniques are used to identify a set of 'geological primitives' (linear or arc features representing lithological boundaries) within these data. Inclusion of the DEM data provides the three-dimensional co-ordinates of these primitives enabling a least-squares fit to be employed to calculate dip and strike values, based, initially, on the assumption of a simple, linearly dipping structural model. A very large number of scene 'primitives' is identified using these procedures, only some of which have geological significance. Knowledge-based rules are therefore used to identify the relevant. For example, rules are developed to identify lake edges, forest boundaries, forest tracks, rock-vegetation boundaries, and areas of geomorphological interest. Confidence in the geological significance of some of the geological primitives is increased where they are found independently in both the DEM and remotely sensed data. The dip and strike values derived in this way are compared to information taken from the published geological map for this area, as well as measurements taken in the field. Many results are shown to correspond closely to those taken from the map and in the field, with an error of < 1°. These data and rules are incorporated into an expert system which, initially, produces a simple model of the geological structure. The system also provides a graphical user interface for manual control and interpretation, where necessary. Although the system currently only allows a relatively simple structural model (linearly dipping with faulting), in the future it will be possible to extend the system to model more complex features, such as anticlines, synclines, thrusts, nappes, and igneous intrusions.

The generation of post noon F3 layers over the dip equatorial location of Thiruvananthapuram- A new perspective

NASA Astrophysics Data System (ADS)

Mridula, N.; Pant, Tarun Kumar

2018-05-01

In the present paper, occurrence of post noon F3 layers over Thiruvananthapuram (8.5°N; 77°E; dip latitude ∼ 1.5 °N), a dip equatorial station in India have been investigated. F3 layers that occur beyond 13 IST and as observed using ground based ionosonde, for the years 2004-2008 have been studied. Our analysis shows that post noon F3 layers occur mostly on CEJ days around 16 IST to 18 IST. It is found that the time of the ionospheric E-region electric field reversal as inferred from collocated ground based magnetometer observations plays a crucial role in the generation of post noon F3 layers. In fact an early reversal of electric field emerged to be the necessary condition for the formation of post noon F3 layers. A time delay of three to 4 h is observed between the electric field reversal and the formation of F3 layer. It is proposed that this early reversal causes enhanced ionization over dip equatorial region, providing an additional ion drag to the flow of thermospheric zonal wind. This leads to accumulation of more ionization and neutrals culminating in the generation of post noon F3 layers as in the case of pre noon F3 layers. These results reveal that the generation of post noon F3 layers over the dip equatorial region is a natural consequence of the variability associated with the spatio-temporal evolution of EIA and prevailing thermospheric and ionospheric dynamics, and adds a new perspective to the present understanding.

A precisely targeted application strategy of dipping young cucumber fruit in fungicide to control cucumber gray mold.

PubMed

He, Leiming; Cui, Kaidi; Song, Yufei; Zhang, Zhengqun; Li, Beixing; Mu, Wei; Liu, Feng

2018-04-27

Gray mold is a ubiquitous destructive plant disease worldwide. To avoid the shortcomings of conventional spraying systems for controlling this disease, such as high selection pressure on Botrytis cinerea for resistance and fungicide waste resulting from spray drift, a precisely targeted application strategy of dipping young cucumber fruit in a mixture of fungicide and forchlorfenuron (plant growth regulator, PGR) during the bloom period to control cucumber gray mold was developed in the current study. Without leaving above-limit residues in cucumber fruits, dipping in fludioxonil at 30 mg liter -1 provided a greater efficacy (85.4%) against cucumber gray mold than did spraying at 100 mg liter -1 (76.4%). Importantly, fludioxonil mixed with forchlorfenuron from 25 to 35 mg liter -1 increased the yield of cucumbers by 26.2%-36.7% compared to dipping fruit only in forchlorfenuron. The increased yield may be a benefit of controlling gray mold. Dipping fruit in fungicides and PGRs seems to be a potential precisely targeted application strategy to not only control cucumber gray mold effectively but also, through the action of PGRs, to increase the cucumber yield. This novel application method is believed to have a bright prospect in cucumber production in Chinese solar greenhouses. This article is protected by copyright. All rights reserved.

Some examples of deep structure of the Archean from geophysics

NASA Technical Reports Server (NTRS)

Smithson, S. B.; Johnson, R. A.; Pierson, W. R.

1986-01-01

The development of Archean crust remains as one of the significant problems in earth science, and a major unknown concerning Archean terrains is the nature of the deep crust. The character of crust beneath granulite terrains is especially fascinating because granulites are generally interpreted to represent a deep crustal section. Magnetic data from this area can be best modeled with a magnetized wedge of older Archean rocks (granulitic gneisses) underlying the younger Archean greenstone terrain. The dip of the boundary based on magnetic modeling is the same as the dip of the postulated thrust-fault reflection. Thus several lines of evidence indicate that the younger Archean greenstone belt terrain is thrust above the ancient Minnesota Valley gneiss terrain, presumably as the greenstone belt was accreted to the gneiss terrain, so that the dipping reflection represents a suture zone. Seismic data from underneath the granulite-facies Minnesota gneiss terrain shows abundant reflections between 3 and 6 s, or about 9 to 20 km. These are arcuate or dipping multicyclic events indicative of layering.

Future practice of graduates of the New Zealand Diploma of Obstetrics and Gynaecology or Certificate in Women's Health.

PubMed

Miller, Dawn; Roberts, Helen; Wilson, Don

2008-09-22

To determine: why Diploma of Obstetrics (DipObs), Diploma of Obstetrics and Medical Gynaecology (DipOMG), or Certificate in Women's Health graduates enrolled; course usefulness; and subsequent practice. 588 University of Otago DipObs, DipOMG, and Certificate in Women's Health graduates (1992-2006) plus Auckland University graduates (1996-2006) were identified. All were doctors. Questionnaires were sent to the 477 with New Zealand medical registration and responses analysed. 334 of the 477 graduates returned completed questionnaires--70% response rate. 73% had worked as GPs, 10% at family planning clinics, 6% at sexual health clinics; and 13% specialised in OandG. 80% enrolled to further knowledge in women's health, 20% in children's health, and 43% to practise GP obstetrics. Most respondents who enrolled in the 1990s intended to practise GP obstetrics but by 2000 most did not. Of 137 New Zealand-based GP respondents who enrolled to practise GP obstetrics, only 5 (3.6%) currently practise intrapartum obstetric care. Twenty-three GPs still practise shared maternity care. Of 220 primary care practitioners, 90% provide early antenatal care. 93% described the course as useful-extremely useful. The DipObs, Dip OMG and Certificate in Women's Health have continued to provide useful postgraduate training in women's health during a changing time in New Zealand pregnancy care. While many graduates of the 1990s enrolled to practise GP obstetrics, most recent graduates did not, and few GPs still practise intrapartum obstetrics.

Co-sensitization of ZnO by CdS quantum dots in natural dye-sensitized solar cells with polymeric electrolytes to improve the cell stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Junhom, W.; Magaraphan, R.

2015-05-22

The CdS quantum dots (QDs) were deposited on ZnO layer by chemical bath deposition method to absorb light in the shorter wavelength region and used as photoanode in the dye sensitized solar cell (DSSCs) with natural dye extracted from Noni leaves. Microstructures of CdS-ZnO from various dipping time were characterized by XRD, FE-SEM and EDX. The results showed that the CdS is hexagonal structure and the amount of CdS increases when the dipping time increases. The maximal conversion efficiency of 0.292% was achieved by the DSSCs based on CdS QDs-sensitized ZnO film obtained from 9 min-dipping time. Furthermore, the stability ofmore » DSSCs was improved by using polymeric electrolyte. Poly (acrylic acid) (PAA) and Polyacrylamide (PAM) were introduced to CdS QDs-sensitized ZnO film from 9 min-dipping time. Each polymeric electrolyte was prepared by swelling from 0.1-2.0 %w in H2O. The maximal conversion efficiency of 0.207% was achieved for DSSCs based on CdS QDs-sensitized ZnO film with PAM 1.0% and the conversion efficiency was decreased 25% when it was left for1 hr.« less

Co-sensitization of ZnO by CdS quantum dots in natural dye-sensitized solar cells with polymeric electrolytes to improve the cell stability

NASA Astrophysics Data System (ADS)

Junhom, W.; Magaraphan, R.

2015-05-01

The CdS quantum dots (QDs) were deposited on ZnO layer by chemical bath deposition method to absorb light in the shorter wavelength region and used as photoanode in the dye sensitized solar cell (DSSCs) with natural dye extracted from Noni leaves. Microstructures of CdS-ZnO from various dipping time were characterized by XRD, FE-SEM and EDX. The results showed that the CdS is hexagonal structure and the amount of CdS increases when the dipping time increases. The maximal conversion efficiency of 0.292% was achieved by the DSSCs based on CdS QDs-sensitized ZnO film obtained from 9 min-dipping time. Furthermore, the stability of DSSCs was improved by using polymeric electrolyte. Poly (acrylic acid) (PAA) and Polyacrylamide (PAM) were introduced to CdS QDs-sensitized ZnO film from 9 min-dipping time. Each polymeric electrolyte was prepared by swelling from 0.1-2.0 %w in H2O. The maximal conversion efficiency of 0.207% was achieved for DSSCs based on CdS QDs-sensitized ZnO film with PAM 1.0% and the conversion efficiency was decreased 25% when it was left for1 hr.

3D model of fault and fissures structure of the Kovdor Baddeleyite-Apatite-Magnetite Deposit (NE of the Fennoscandian Shield)

NASA Astrophysics Data System (ADS)

Zhirov, Dmitry; Klimov, Sergey

2015-04-01

The Kovdor baddeleyite-apatite-magnetite deposit (KBAMD) is represented by a large vertical ore body and is located in the southwestern part of the Kovdor ultramafic-alkaline central-type intrusion. The intrusion represents a concentrically zoned complex of rocks with an oval shape in plan, and straight zoning, which complies with the injection and displacement of each of further magma phases from the center towards the periphery. The operation of the deposit in open pits started in 1962, and nowadays, it has produced over 500,000,000 tons of ore. This is one of the largest open pits in the Kola region, which is ca. 2 km long, 1.8 km wide, and over 400 m deep. Regular structural studies has been carried out since late 1970. A unique massif of spatial data has been accumulated so far to include over 25,000 measurements of fissures and faults from the surface, ca. 20,000 measurements of fissures in the oriented drill core (over 18 km) etc. Using this data base the 3D model of fault and fissures structure was designed. The analysis of one has resulted in the identification of a series of laws and features, which are necessary to be taken into account when designing a deep open pit and mining is carried out. These are mainly aspects concerning the origin, kinematics, mechanics and ratio of spatial extension of various fault systems, variation of their parameters at deep horizons, features of a modern stress field in the country rocks, etc. The 3D model has allowed to divide the whole fracture / fissure systems of the massif rocks into 2 large groups: prototectonic system of joints, including cracks of 'liquid magmatic (carbonatite stage) contraction genesis', and newly formed faults due to the superimposed tectonic stages. With regard to the deposit scale, these are characterized as intraformational and transformational, respectively. Each group shows a set (an assemblage) of fault systems with unique features and signs, as well as regular interconnections. The prototectonic assemblage of fissures includes the following main systems: 2-3 subsystems Rd of radial with angle of dip within 65-90° (median at 78°), two subsystems S of a circular subvertical (tangential, crossing Rd) with angle of dip within 60-90° (74°), and two diagonal-conic ones: a centriclinal C dipping towards the center of the intrusion at angles of 25-55° (43°), and a periclinal P dipping from the center of the intrusion at angles of 5-35° (18°). The system of subhorizontal joints L (angle of dip within 0-12°) at deep horizons is insignificantly manifested. All the prototectonic systems are regularly interrelated, and vary asymuthal features according to the law of axial symmetry (when moving around the vertical axis of symmetry passed through the geometric center of the carbonatite intrusion). The superimposed tectonics of post-ore stages forms a few large faults and systems of rupture discontinuities. A few (up to 3) variously oriented displacements are documented in the field on kinematic features (slide furrows, oriented cleavages). They were used for reconstruction of stresses and tectonic evolution. The superimposed tectonic faulting has heterogeneous (local) distribution in the rocks of the deposit, and slight predictability of main parameters. This study was supported by the Russian Scientific Fund (project nos. 14-17-00751).

Influence of the coating process on the tribological conditions during cold forging with a MoS2 based lubricant

NASA Astrophysics Data System (ADS)

Lorenz, Robby; Hagenah, Hinnerk; Merklein, Marion

2018-05-01

Cold forging processes such as forward rod extrusion can be used to produce high quality components like connection rods, shafts and gears. The main advantages of these extruded components are sufficient surface quality, work hardening, compressive residual stresses and fatigue strength. Since one technical disadvantage of extruded components lies in the achievable tolerance classes, the improvement of these should be of crucial importance. For instance, the attainable workpiece accuracy and component quality can be influenced by adapting the tribological system in such a way that the resulting friction is specifically controlled in order to improve component forming. Lubricant modification is one practical way of adapting the tribological system to the requirements of the forming process. An industrial established and highly efficient lubricant system is the application of a zinc-phosphate conversion layer with a molybdenum disulfide-based lubricant. While offering many advantages, its tribological conditions seem to depend strongly on the layer weight and the application strategy. These parameters and the respective interdependencies have not been sufficiently investigated yet. In order to examine this, the tribological conditions depending on the layer weight are analyzed in greater detail using the Ring-Compression-Test (RCT). This tribometer provides a comparative representation of the forming conditions during cold forging. Furthermore, a potential dependency between the tribological conditions and two different coating techniques is analyzed. The latter are represented by the industrial standards dipping and dip-drumming.

Dip-slope and Dip-slope Failures in Taiwan - a Review

NASA Astrophysics Data System (ADS)

Lee, C.

2011-12-01

Taiwan is famous for dip-slope and dip-slope slides. Dip-slopes exist at many places in the fold-and-thrust belt of Taiwan. Under active cutting of stream channels and man-made excavations, a dip-slope may become unstable and susceptible for mass sliding. Daylight of a bedding parallel clay seam is the most dangerous type for dip-slope sliding. Buckling or shear-off features may also happen at toe of a long dip-slope. Besides, a dip-slope is also dangerous for shallow debris slides, if the slope angle is between 25 to 45 degrees and the debris (colluvium or slope wash) is thick (>1m). These unstable slopes may slide during a triggering event, earthquake or typhoon storm; or even slide without a triggering event, like the 2010 Tapu case. Initial buckling feature had been found in the dip-slope of the Feitsui arch dam abutment after detailed explorations. Shear-off feature have also been found in dip-slope located in right bank of the Nahua reservoir after field investigation and drilling. The Chiufengerhshan slide may also be shear-off type. On the other hand, the Tapu, the Tsaoling slides and others are of direct slide type. The Neihoo Bishan slide is a shallow debris slide on dip-slope. All these cases demonstrate the four different types of dip-slope slide. The hazard of a dip-slope should be investigated to cover these possible types of failure. The existence of bedding parallel clay seams is critical for the stability of a dip-slope, either for direct slide or buckling or shear-off type of failure, and is a hot point during investigation. Because, the stability of a dip-slope is changing with time, therefore, detailed explorations to including weathering and erosion rates are also very necessary to ensure the long-term stability of a dip-slope.

Initiation and Along-Axis Segmentation of Seaward-Dipping Volcanic Sequences Captured in Afar

NASA Astrophysics Data System (ADS)

Ebinger, C.; Wolfenden, E.; Yirgu, G.; Keir, D.

2003-12-01

The Afar triple junction zone provides a unique opportunity to examine the early development of magmatic margins, as respective limbs of the triple junction capture different stages of the breakup process. Initial rifting in the southernmost Red Sea occurred concurrent with, or soon after flood basaltic magmatism at ~31 Ma in the Ethiopia-Yemen plume province, whereas the northern part of the Main Ethiopian rift initiated after 12 Ma. Both rift systems initiated with the development of high-angle border fault systems bounding broad basins, but 8-10 My after rifting we see riftward migration of strain from the western border fault to narrow zones of increasingly more basaltic magmatism. These localised zones of faulting and volcanism (magmatic segments) show a segmentation independent of the border fault segmentation. The much older, more evolved magmatic segments in the southern Red Sea, where not onlapped by Pliocene-Recent sedimentary strata, dip steeply riftward and define a regional eastward flexure into transitional oceanic crust, as indicated by gravity models constrained by seismic refraction and receiver function data. The southern Red Sea magmatic segments have been abandoned in Pliocene-Recent triple junction reorganisations, whereas the process of seaward-dipping volcanic sequence emplacement is ongoing in the seismically and volcanically active Main Ethiopian rift. Field, remote sensing, gravity, and seismicity data from the Main Ethiopian and southern Red Sea rifts indicate that seaward-dipping volcanic sequences initiate in moderately stretched continental crust above a narrow zone of dike-intrusion. Our comparison of active and ancient magmatic segments show that they are the precursors to seaward-dipping volcanic sequences analogous to those seen on passive continental margins, and provides insights into the initiation of along-axis segmentation of seafloor-spreading centers.

Corrosion of Nickel-Based Alloys in Ultra-High Temperature Heat Transfer Fluid

NASA Astrophysics Data System (ADS)

Wang, Tao; Reddy, Ramana G.

2017-03-01

MgCl2-KCl binary system has been proposed to be used as high temperature reactor coolant. Due to its relatively low melting point, good heat capacity and excellent thermal stability, this system can also be used in high operation temperature concentrating solar power generation system as heat transfer fluid (HTF). The corrosion behaviors of nickel based alloys in MgCl2-KCl molten salt system at 1,000 °C were determined based on long-term isothermal dipping test. After 500 h exposure tests under strictly maintained high purity argon gas atmosphere, the weight loss and corrosion rate analysis were conducted. Among all the tested samples, Ni-201 demonstrated the lowest corrosion rate due to the excellent resistance of Ni to high temperature element dissolution. Detailed surface topography and corrosion mechanisms were also determined by using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS).

Significant structural reinterpretation of the giant October Field, Gulf of Suez, Egypt using SCAT, isogon based sections and 3D seismic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sercombe, W.J.; Smith, G.W.; Morse, J.D.

1996-01-01

The October field, a sub-salt giant in the extensional Gulf of Suez (Egypt) has been structurally reinterpreted for new reserve opportunities. Quantitative SCAT analyses of the wellbore dip data have been integrated with 3D seismic by using dip isogons to construct local structural sections. SCAT dip analysis was critical to the reinterpretation because SCAT revealed important structural information that previously was unresolvable using conventional tadpole plots. In gross aspect, the October Field is a homocline that trends NW-SE, dips to the NE, and is closed on the SW (updip) by the major Clysmic Normal Fault. SCAT accurately calculated the overallmore » trend of the field, but also identified important structural anomalies near the Clysmic fault and in the northwest and southeast plunge ends. In the northwest plunge end, SCAT has identified new, south dipping blocks that are transitional to the structurally-higher North October field. The southeast plunge end has been reinterpreted with correct azimuthal trends and new fault-block prospects. These new SCAT results have successfully improved the 3D seismic interpretation by providing a foundation of accurate in-situ structural control in an area of poor-to-fair seismic quality below the Miocene salt package.« less

Significant structural reinterpretation of the giant October Field, Gulf of Suez, Egypt using SCAT, isogon based sections and 3D seismic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sercombe, W.J.; Smith, G.W.; Morse, J.D.

1996-12-31

The October field, a sub-salt giant in the extensional Gulf of Suez (Egypt) has been structurally reinterpreted for new reserve opportunities. Quantitative SCAT analyses of the wellbore dip data have been integrated with 3D seismic by using dip isogons to construct local structural sections. SCAT dip analysis was critical to the reinterpretation because SCAT revealed important structural information that previously was unresolvable using conventional tadpole plots. In gross aspect, the October Field is a homocline that trends NW-SE, dips to the NE, and is closed on the SW (updip) by the major Clysmic Normal Fault. SCAT accurately calculated the overallmore » trend of the field, but also identified important structural anomalies near the Clysmic fault and in the northwest and southeast plunge ends. In the northwest plunge end, SCAT has identified new, south dipping blocks that are transitional to the structurally-higher North October field. The southeast plunge end has been reinterpreted with correct azimuthal trends and new fault-block prospects. These new SCAT results have successfully improved the 3D seismic interpretation by providing a foundation of accurate in-situ structural control in an area of poor-to-fair seismic quality below the Miocene salt package.« less

Sentinel-1 observation of the 2017 Sangsefid earthquake, northeastern Iran: Rupture of a blind reserve-slip fault near the Eastern Kopeh Dagh

NASA Astrophysics Data System (ADS)

Xu, Guangyu; Xu, Caijun; Wen, Yangmao

2018-04-01

New satellites are now revealing InSAR-based surface deformation within a week after natural hazard events. Quick hazard responses will be more publically accessible and provide information to responding agencies. Here we used Sentinel-1 interferometric synthetic aperture radar (InSAR) data to investigate coseismic deformation associated with the 2017 Sangsefid earthquake, which occurred in the southeast margin of the Kopeh Dagh fault system. The ascending and descending interferograms indicate thrust-dominated slip, with the maximum line-of-sight displacement of 10.5 and 13.7 cm, respectively. The detailed slip-distribution of the 2017 Sangsefid Mw6.1 earthquake inferred from geodetic data is presented here for the first time. Although the InSAR interferograms themselves do not uniquely constrain what the primary slip surface is, we infer that the source fault dips to southwest by analyzing the 2.5 D displacement field decomposed from the InSAR observations. The determined uniform slip fault model shows that the dip angle of the seimogenic fault is approximately 40°, with a strike of 120° except for a narrower fault width than that predicted by the empirical scaling law. We suggest that geometric complexities near the Kopeh Dagh fault system obstruct the rupture propagation, resulting in high slip occurred within a small area and much higher stress drop than global estimates. The InSAR-determined moment is 1.71 × 1018 Nm with a shear modulus of 3.32 × 1010 N/m2, equivalent to Mw 6.12, which is consistent with seismological results. The finite fault model (the west-dipping fault plane) reveals that the peak slip of 0.90 m occurred at a depth of 6.3 km, with substantial slip at a depth of 4-10 km and a near-uniform slip of 0.1 m at a depth of 0-2.5 km. We suggest that the Sangsefid earthquake occurred on an unknown blind reverse fault dipping southwest, which can also be recognised through observing the long-term surface effects due to the existence of the blind fault.

Influence of AlN(0001) Surface Reconstructions on the Wettability of an Al/AlN System: A First-Principle Study.

PubMed

Cao, Junhua; Liu, Yang; Ning, Xiao-Shan

2018-05-11

A successful application of a hot dip coating process that coats aluminum (Al) on aluminum nitride (AlN) ceramics, revealed that Al had a perfect wettability to the ceramics under specific circumstances, which was different from previous reports. In order to elucidate the mechanism that controlled the supernormal wetting phenomenon during the dip coating, a first-principle calculation of an Al(111)/AlN(0001) interface, based on the density functional theory (DFT), was employed. The wettability of the Al melt on the AlN(0001) surface, as well as the effect that the surface reconstruction of AlN and the oxygen adsorption had on Al for the adhesion and the wettability of the Al/AlN system, were studied. The results revealed that a LCM (laterally contracted monolayer) reconstruction could improve the adhesion and wettability of the system. Oxygen adsorption on the free surface of Al decreased the contact angle, because the adsorption reduced of the surface tension of Al. A prefect wetting was obtained only after some of the oxygen atoms adsorbed on the free surface of Al. The supernormal wetting phenomenon came from the surface reconstruction of the AlN and the adsorption of oxygen atoms on the Al melt surface.

Discovery of Rapidly Moving Partial X-Ray Absorbers Within Cassiopeiae

NASA Technical Reports Server (NTRS)

Hamaguchi, K.; Oskinova, L.; Russell, C. M. P.; Petre, R.; Enoto, T.; Morihana, K.; Ishida, M.

2016-01-01

Gamma Cassiopeiae is an enigmatic Be star with unusually strong hard X-ray emission. The Suzaku observatory detected six rapid X-ray spectral hardening events called "softness dips" in a approx.100 ks observation in 2011. All the softness dip events show symmetric softness-ratio variations, and some of them have flat bottoms apparently due to saturation. The softness dip spectra are best described by either approx.40% or approx.70% partial covering absorption to kT approx.12 keV plasma emission by matter with a neutral hydrogen column density of approx.(2-8) ×10(exp 21)/sq cm, while the spectrum outside these dips is almost free of absorption. This result suggests the presence of two distinct X-ray-emitting spots in the gamma Cas system, perhaps on a white dwarf (WD) companion with dipole mass accretion. The partial covering absorbers may be blobs in the Be stellar wind, the Be disk, or rotating around the WD companion. Weak correlations of the softness ratios to the hard X-ray flux suggest the presence of stable plasmas at kT approx 0.9 and 5 keV, which may originate from the Be or WD winds. The formation of a Be star and WD binary system requires mass transfer between two stars; gamma Cas may have experienced such activity in the past.

The influence of normal fault geometry on porous sandstone deformation: Insights from mechanical models into conditions leading to Coulomb failure and shear-enhanced compaction

NASA Astrophysics Data System (ADS)

Allison, K.; Reinen, L. A.

2011-12-01

Slip on non-planar faults produces stress perturbations in the surrounding host rock that can yield secondary faults at a scale too small to be resolved on seismic surveys. Porosity changes during failure may affect the ability of the rock to transmit fluids through dilatant cracking or, in porous rocks, shear-enhanced compaction (i.e., cataclastic flow). Modeling the mechanical behavior of the host rock in response to slip on non-planar faults can yield insights into the role of fault geometry on regions of enhanced or inhibited fluid flow. To evaluate the effect of normal fault geometry on deformation in porous sandstones, we model the system as a linear elastic, homogeneous, whole or half space using the boundary-element modeling program Poly3D. We consider conditions leading to secondary deformation using the maximum Coulomb shear stress (MCSS) as an index of brittle deformation and proximity to an elliptical yield envelope (Y), determined experimentally for porous sandstone (Baud et al., JGR, 2006), for cataclastic flow. We model rectangular faults consisting of two segments: an upper leg with a constant dip of 60° and a lower leg with dips ranging 15-85°. We explore far-field stress models of constant and gradient uniaxial strain. We investigate the potential damage in the host rock in two ways: [1] the size of the damage zone, and [2] regions of enhanced deformation indicated by elevated MCSS or Y. Preliminary results indicate that, along a vertical transect passing through the fault kink, [1] the size of the damage zone increases in the footwall with increasing lower leg dip and remains constant in the hanging wall. [2] In the footwall, the amount of deformation does not change as a function of lower leg dip in constant stress models; in gradient stress models, both MCSS and Y increase with dip. In the hanging wall, Y decreases with increasing lower leg dip for both constant and gradient stress models. In contrast, MCSS increases: as lower leg dip increases for constant stress models, and as the difference between lower leg dip and 60° increases for gradient stress models. These preliminary results indicate that the dip of the lower fault segment significantly affects the amount and style of deformation in the host rock.

On the use of imaginary faults in palaeostress analysis

NASA Astrophysics Data System (ADS)

Shan, Yehua; Liang, Xinquan

2017-11-01

The imaginary fault refers to the counterpart of a certain given fault that has a similar expression about the Wallace-Bott hypothesis. It is included to further reduce the feasible fields for the principal stress directions using the right dihedra method. The given fault and its imaginary fault have a similar dip-slip sense under the extensional or compressional regime but, as proved in this paper, a different dip-slip sense under the strike-slip regime. Their relation in dip-slip sense does no change with the rotation of the coordinate system, thus making possible the general use in the reduction of the imaginary faults under any tectonic regime. A procedure for this use is proposed and applied to a real example to demonstrate the feasibility of this method.

Discriminating the tectonic and non-tectonic contributions in the ionospheric signature of the 2011, Mw7.1, dip-slip Van earthquake, Eastern Turkey

NASA Astrophysics Data System (ADS)

Rolland, Lucie M.; Vergnolle, Mathilde; Nocquet, Jean-Mathieu; Sladen, Anthony; Dessa, Jean-Xavier; Tavakoli, Farokh; Nankali, Hamid Reza; Cappa, FréDéRic

2013-06-01

It has previously been suggested that ionospheric perturbations triggered by large dip-slip earthquakes might offer additional source parameter information compared to the information gathered from land observations. Based on 3D modeling of GPS- and GLONASS-derived total electron content signals recorded during the 2011 Van earthquake (thrust, intra-plate event, Mw = 7.1, Turkey), we confirm that coseismic ionospheric signals do contain important information about the earthquake source, namely its slip mode. Moreover, we show that part of the ionospheric signal (initial polarity and amplitude distribution) is not related to the earthquake source, but is instead controlled by the geomagnetic field and the geometry of the Global Navigation Satellite System satellites constellation. Ignoring these non-tectonic effects would lead to an incorrect description of the earthquake source. Thus, our work emphasizes the added caution that should be used when analyzing ionospheric signals for earthquake source studies.

Discriminating the tectonic and non-tectonic contributions in the ionospheric signature of the 2011, Mw 7.1, dip-slip Van earthquake, Eastern Turkey (Invited)

NASA Astrophysics Data System (ADS)

Rolland, L. M.; Vergnolle, M.; Nocquet, J.; Sladen, A.; Dessa, J.; Tavakoli, F.; Nankali, H.; Cappa, F.

2013-12-01

It has previously been suggested that ionospheric perturbations triggered by large dip-slip earthquakes might offer additional source parameter information compared to the information gathered from land observations. Based on 3D modeling of GPS- and GLONASS-derived total electron content signals recorded during the 2011 Van earthquake (thrust, intra-plate event, Mw = 7.1, Turkey), we confirm that coseismic ionospheric signals do contain important information about the earthquake source, namely its slip mode. Moreover, we show that part of the ionospheric signal (initial polarity and amplitude distribution) is not related to the earthquake source, but is instead controlled by the geomagnetic field and the geometry of the Global Navigation Satellite System satellites constellation. Ignoring these non-tectonic effects would lead to an incorrect description of the earthquake source. Thus, our work emphasizes the added caution that should be used when analyzing ionospheric signals for earthquake source studies.

Where and why do large shallow intraslab earthquakes occur?

NASA Astrophysics Data System (ADS)

Seno, Tetsuzo; Yoshida, Masaki

2004-03-01

We try to find how often, and in what regions large earthquakes ( M≥7.0) occur within the shallow portion (20-60 km depth) of a subducting slab. Searching for events in published individual studies and the Harvard University centroid moment tensor catalogue, we find twenty such events in E. Hokkaido, Kyushu-SW, Japan, S. Mariana, Manila, Sumatra, Vanuatu, N. Chile, C. Peru, El Salvador, Mexico, N. Cascadia and Alaska. Slab stresses revealed from the mechanism solutions of these large intraslab events and nearby smaller events are almost always down-dip tensional. Except for E. Hokkaido, Manila, and Sumatra, the upper plate shows horizontal stress gradient in the arc-perpendicular direction. We infer that shear tractions are operating at the base of the upper plate in this direction to produce the observed gradient and compression in the outer fore-arc, balancing the down-dip tensional stress of the slab. This tectonic situation in the subduction zone might be realized as part of the convection system with some conditions, as shown by previous numerical simulations.

A Viscoelastic earthquake simulator with application to the San Francisco Bay region

USGS Publications Warehouse

Pollitz, Fred F.

2009-01-01

Earthquake simulation on synthetic fault networks carries great potential for characterizing the statistical patterns of earthquake occurrence. I present an earthquake simulator based on elastic dislocation theory. It accounts for the effects of interseismic tectonic loading, static stress steps at the time of earthquakes, and postearthquake stress readjustment through viscoelastic relaxation of the lower crust and mantle. Earthquake rupture initiation and termination are determined with a Coulomb failure stress criterion and the static cascade model. The simulator is applied to interacting multifault systems: one, a synthetic two-fault network, and the other, a fault network representative of the San Francisco Bay region. The faults are discretized both along strike and along dip and can accommodate both strike slip and dip slip. Stress and seismicity functions are evaluated over 30,000 yr trial time periods, resulting in a detailed statistical characterization of the fault systems. Seismicity functions such as the coefficient of variation and a- and b-values exhibit systematic patterns with respect to simple model parameters. This suggests that reliable estimation of the controlling parameters of an earthquake simulator is a prerequisite to the interpretation of its output in terms of seismic hazard.

Chandra X-ray Spectroscopy of the Focused Wind In the Cygnus X-1 System I. The Non-Dip Spectrum in the Low/Hard State

NASA Technical Reports Server (NTRS)

Hanke, Manfred; Wilms, Jorn; Nowak, Michael A.; Pottschmidt, Katja; Schultz, Norbert S.; Lee, Julia C.

2008-01-01

We present analyses of a 50 ks observation of the supergiant X-ray binary system CygnusX-1/HDE226868 taken with the Chandra High Energy Transmission Grating Spectrometer (HETGS). CygX-1 was in its spectrally hard state and the observation was performed during superior conjunction of the black hole, allowing for the spectroscopic analysis of the accreted stellar wind along the line of sight. A significant part of the observation covers X-ray dips as commonly observed for CygX-1 at this orbital phase, however, here we only analyze the high count rate non-dip spectrum. The full 0.5-10 keV continuum can be described by a single model consisting of a disk, a narrow and a relativistically broadened Fe K line, and a power law component, which is consistent with simultaneous RXTE broad band data. We detect absorption edges from overabundant neutral O, Ne and Fe, and absorption line series from highly ionized ions and infer column densities and Doppler shifts. With emission lines of He-like Mg XI, we detect two plasma components with velocities and densities consistent with the base of the spherical wind and a focused wind. A simple simulation of the photoionization zone suggests that large parts of the spherical wind outside of the focused stream are completely ionized, which is consistent with the low velocities (<200 km/s) observed in the absorption lines, as the position of absorbers in a spherical wind at low projected velocity is well constrained. Our observations provide input for models that couple the wind activity of HDE 226868 to the properties of the accretion flow onto the black hole.

Geometry of slab, intraslab stress field and its tectonic implication in the Nankai trough, Japan

NASA Astrophysics Data System (ADS)

Xu, J.; Kono, Y.

2002-07-01

The characteristics of geometry of slabs and the intraslab stress field in the Nankai subduction zone, Japan, were analyzed based on highly accurate hypocentral data and focal mechanism solutions. The results suggest that the shallow seismic zone of the Philippine Sea slab subducts with dip angels between 10 and 22 degrees beneath Shikoku and the Kii peninsula, and between 11 and 40 degrees beneath Kyushu. Two types of seismogenic stress field exist within the slab. The stress field of down-dip compression type can be seen in the slab beneath Shikoku and the Kii peninsula, where the horizontal component of regional compression stress is NNW. On the other hand the stress field of down-dip extension type within the slab is dominant in the region from western Shikoku to Kyushu, where the direction of horizontal compressive stress is near WWN. The existence of the two types of stress field is related to the differences of slab geometry and slab age of the subduciton zone. These properties imply that slab beneath Kyushu (40 Ma) probably is older than that beneath Shikoku and the Kii peninsula (11-20 Ma). The young slab of the oceanic Philippine Sea plate subducts with a shallow angle beneath the Eurasian plate in Shikoku and the Kii peninsula. The subduction has encountered strong resistance there, resulting in a down-dip compression stress field. The down-dip extension stress field may be related to the older slab of the Philippine Sea plate which subducts beneath Kyushu with a steeper dip angle.

Eigenvector of gravity gradient tensor for estimating fault dips considering fault type

NASA Astrophysics Data System (ADS)

Kusumoto, Shigekazu

2017-12-01

The dips of boundaries in faults and caldera walls play an important role in understanding their formation mechanisms. The fault dip is a particularly important parameter in numerical simulations for hazard map creation as the fault dip affects estimations of the area of disaster occurrence. In this study, I introduce a technique for estimating the fault dip using the eigenvector of the observed or calculated gravity gradient tensor on a profile and investigating its properties through numerical simulations. From numerical simulations, it was found that the maximum eigenvector of the tensor points to the high-density causative body, and the dip of the maximum eigenvector closely follows the dip of the normal fault. It was also found that the minimum eigenvector of the tensor points to the low-density causative body and that the dip of the minimum eigenvector closely follows the dip of the reverse fault. It was shown that the eigenvector of the gravity gradient tensor for estimating fault dips is determined by fault type. As an application of this technique, I estimated the dip of the Kurehayama Fault located in Toyama, Japan, and obtained a result that corresponded to conventional fault dip estimations by geology and geomorphology. Because the gravity gradient tensor is required for this analysis, I present a technique that estimates the gravity gradient tensor from the gravity anomaly on a profile.

Numerical method for high accuracy index of refraction estimation for spectro-angular surface plasmon resonance systems.

PubMed

Alleyne, Colin J; Kirk, Andrew G; Chien, Wei-Yin; Charette, Paul G

2008-11-24

An eigenvector analysis based algorithm is presented for estimating refractive index changes from 2-D reflectance/dispersion images obtained with spectro-angular surface plasmon resonance systems. High resolution over a large dynamic range can be achieved simultaneously. The method performs well in simulations with noisy data maintaining an error of less than 10(-8) refractive index units with up to six bits of noise on 16 bit quantized image data. Experimental measurements show that the method results in a much higher signal to noise ratio than the standard 1-D weighted centroid dip finding algorithm.

Thermal Stress and Heat Transfer Coefficient for Ceramics Stalk Having Protuberance Dipping into Molten Metal

NASA Astrophysics Data System (ADS)

Noda, Nao-Aki; Hendra; Li, Wenbin; Takase, Yasushi; Ogura, Hiroki; Higashi, Yusuke

Low pressure die casting is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The low pressure die casting process plays an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. In the low pressure die casting process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal, by means of a pressurized gas, to rise into a ceramic tube having protuberance, which connects the die to the furnace. The ceramics tube, called stalk, has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk having protuberance is dipped into the molten aluminum. It is important to reduce the risk of fracture that may happen due to the thermal stresses. In this paper, thermo-fluid analysis is performed to calculate surface heat transfer coefficient. The finite element method is applied to calculate the thermal stresses when the stalk having protuberance is dipped into the crucible with varying dipping speeds. It is found that the stalk with or without protuberance should be dipped into the crucible slowly to reduce the thermal stress.

Development of advanced Czochralski growth process to produce low cost 150 kg silicon ingots from a single crucible for technology readiness. [crystal growth

NASA Technical Reports Server (NTRS)

Lane, R. L.

1981-01-01

Six growth runs used the Kayex-Hameo Automatic Games Logic (AGILE) computer based system for growth from larger melts in the Mod CG2000. The implementation of the melt pyrometer sensor allowed for dip temperature monitoring and usage by the operator/AGILE system. Use of AGILE during recharge operations was successfully evaluated. The tendency of crystals to lose cylindrical shape (spiraling) continued to be a problem. The hygrometer was added to the Furnace Gas Analysis System and used on several growth runs. The gas chromatograph, including the integrator, was also used for more accurate carbon monoxide concentration measurements. Efforts continued for completing the automation of the total Gas Analysis System. An economic analysis, based on revised achievable straight growth rate, is presented.

Expert systems for automated correlation and interpretation of wireline logs

USGS Publications Warehouse

Olea, R.A.

1994-01-01

CORRELATOR is an interactive computer program for lithostratigraphic correlation of wireline logs able to store correlations in a data base with a consistency, accuracy, speed, and resolution that are difficult to obtain manually. The automatic determination of correlations is based on the maximization of a weighted correlation coefficient using two wireline logs per well. CORRELATOR has an expert system to scan and flag incongruous correlations in the data base. The user has the option to accept or disregard the advice offered by the system. The expert system represents knowledge through production rules. The inference system is goal-driven and uses backward chaining to scan through the rules. Work in progress is used to illustrate the potential that a second expert system with a similar architecture for interpreting dip diagrams could have to identify episodes-as those of interest in sequence stratigraphy and fault detection- and annotate them in the stratigraphic column. Several examples illustrate the presentation. ?? 1994 International Association for Mathematical Geology.

An Analysis of the Naval Postgraduate School’s Commissioned Officers’ and Faculty Club Accounting System

DTIC Science & Technology

1988-06-01

cheese, vinaigarette) VEGETABLES Buttered Carrots Peas w/Mushrooms Green Beans Almondine Mixed Vegetables Corn w/Pimentos *Broccoli w/ Hollandaise Sauce ...PRAWNS W/COCKTAIL SAUCE $14.75 GRILLED HALIBUT STEAK 11.25 (lemon hollandaise sauce ) HERB BAKED ICELANDIC COD 8.90 (bechemel sauce ) SHRIMP CURRY ON A BED...Meatballs Fruit Boat Vegetable Tray w/Dip 3.10 Chicken Nuggets w/ Sauce Dip Cheeseboard w/Crackers Deviled Eggs 2. Chicken (or) Seafood Carolines

Simulating the responses of a low-trophic ecosystem in the East China Sea to decadal changes in nutrient load from the Changjiang (Yangtze) River

NASA Astrophysics Data System (ADS)

Wang, Yucheng; Guo, Xinyu; Zhao, Liang

2018-01-01

Using a three-dimensional coupled biophysical model, we simulated the responses of a lowtrophic ecosystem in the East China Sea (ECS) to long-term changes in nutrient load from the Changjiang (Yangtze) River over the period of 1960-2005. Two major factors affected changes in nutrient load: changes in river discharge and the concentration of nutrients in the river water. Increasing or decreasing Changjiang discharge induced different responses in the concentrations of nutrients, phytoplankton, and detritus in the ECS. Changes in dissolved inorganic nitrogen (DIN), silicate (SIL), phytoplankton, and detritus could be identified over a large area of the ECS shelf, but changes in dissolved inorganic phosphate (DIP) were limited to a small area close to the river mouth. The high DIN:DIP and SIL:DIP ratios in the river water were likely associated with the different responses in DIN, DIP, and SIL. As DIP is a candidate limiting nutrient, perturbations in DIP resulting from changes in the Changjiang discharge are quickly consumed through primary production. It is interesting that an increase in the Changjiang discharge did not always lead to an increase in phytoplankton levels in the ECS. Phytoplankton decreases could be found in some areas close to the river mouth. A likely cause of the reduction in phytoplankton was a change in the hydrodynamic field associated with the river plume, although the present model is not suitable for examining the possibility in detail. Increases in DIN and DIP concentrations in the river water primarily led to increases in DIN, DIP, phytoplankton, and detritus levels in the ECS, whereas decreases in the SIL concentration in river water led to lower SIL concentrations in the ECS, indicating that SIL is not a limiting nutrient for photosynthesis, based on our model results from 1960 to 2005. In both of the above-mentioned cases, the sediment accumulation rate of detritus exhibited a large spatial variation near the river mouth, suggesting that core sample data should be carefully interpreted.

Benchmark Computation and Finite Element Performance Evaluation for a Rhombic Plate Bending Problem

DTIC Science & Technology

1987-09-01

Physical Science and Technology University of Maryland, College Park, MD 20742, USA and Dip. Matematica - Universita di Pavia - 27100 Pavia - ITALY DTIC...University of Maryland, College Park,, MD 20742, USA , and Dip. Matematica - Universita di Pavia - 27100 Pavia - ITALY SFor Oe" -- 4- I , CA& 11 --l...drawn when based on the state of the art of both theoretical and experience field. The reliability has to be understood not only with respect to a

Statistical study of ductility-dip cracking induced plastic deformation in polycrystalline laser 3D printed Ni-based superalloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qian, Dan; Xue, Jiawei; Zhang, Anfeng

Ductility-dip cracking in Ni-based superalloy, resulting from heat treatment, is known to cause disastrous failure, but its mechanism is still not completely clear. A statistical study of the cracking behavior as a function of crystal orientation in a laser 3D-printed DL125L Ni-based superalloy polycrystal is investigated here using the synchrotron X-ray microdiffraction. The dislocation slip system in each of the forty crystal grains adjacent to the 300 μm long crack has been analyzed through Laue diffraction peak shapes. In all these grains, edge-type geometrically necessary dislocations (GNDs) dominate, and their dislocation line directions are almost parallel to the crack plane.more » Based on Schmid's law, the equivalent uniaxial tensile force direction is revealed normal to the trace of the crack. A qualitative mechanism is thus proposed. Thermal tensile stress perpendicular to the laser scanning direction is elevated due to a significant temperature gradient, and thus locations in the materials where the thermal stress exceeds the yield stress undergo plastic deformation mediated by GND activations. As the dislocations slip inside the crystal grains and pile up at the grain boundaries, local strain/stress keeps increasing, until the materials in these regions fail to sustain further deformation, leading to voids formation and cracks propagation.« less

Statistical study of ductility-dip cracking induced plastic deformation in polycrystalline laser 3D printed Ni-based superalloy

DOE PAGES

Qian, Dan; Xue, Jiawei; Zhang, Anfeng; ...

2017-06-06

Ductility-dip cracking in Ni-based superalloy, resulting from heat treatment, is known to cause disastrous failure, but its mechanism is still not completely clear. A statistical study of the cracking behavior as a function of crystal orientation in a laser 3D-printed DL125L Ni-based superalloy polycrystal is investigated here using the synchrotron X-ray microdiffraction. The dislocation slip system in each of the forty crystal grains adjacent to the 300 μm long crack has been analyzed through Laue diffraction peak shapes. In all these grains, edge-type geometrically necessary dislocations (GNDs) dominate, and their dislocation line directions are almost parallel to the crack plane.more » Based on Schmid's law, the equivalent uniaxial tensile force direction is revealed normal to the trace of the crack. A qualitative mechanism is thus proposed. Thermal tensile stress perpendicular to the laser scanning direction is elevated due to a significant temperature gradient, and thus locations in the materials where the thermal stress exceeds the yield stress undergo plastic deformation mediated by GND activations. As the dislocations slip inside the crystal grains and pile up at the grain boundaries, local strain/stress keeps increasing, until the materials in these regions fail to sustain further deformation, leading to voids formation and cracks propagation.« less

High-performance magnetic field sensor based on superconducting quantum interference filters

NASA Astrophysics Data System (ADS)

Caputo, P.; Oppenländer, J.; Häussler, Ch.; Tomes, J.; Friesch, A.; Träuble, T.; Schopohl, N.

2004-08-01

We have developed an absolute magnetic field sensor using a superconducting quantum interference filter (SQIF) made of high-Tc grain-boundary Josephson junctions. The device shows the typical magnetic-field-dependent voltage response V(B ), which is a sharp deltalike dip in the vicinity of zero-magnetic field. When the SQIF is cooled with magnetic shield, and then the shield is removed, the presence of the ambient magnetic field induces a shift of the dip position from B0≈0 to a value B ≈B1, which is about the average value of the Earth's magnetic field, at our latitude. When the SQIF is cooled in the ambient field without shielding, the dip is first found at B ≈B1, and the further shielding of the SQIF results in a shift of the dip towards B0≈0. The low hysteresis observed in the sequence of experiments (less than 5% of B1) makes SQIFs suitable for high precision measurements of the absolute magnetic field. The experimental results are discussed in view of potential applications of high-Tc SQIFs in magnetometry.

Slip and Dilation Tendency Anlysis of McGinness Hills Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

Slip and Dilation Tendency in focus areas Critically stressed fault segments have a relatively high likelihood of acting as fluid flow conduits (Sibson, 1994). As such, the tendency of a fault segment to slip (slip tendency; Ts; Morris et al., 1996) or to dilate (dilation tendency; Td; Ferrill et al., 1999) provides an indication of which faults or fault segments within a geothermal system are critically stressed and therefore likely to transmit geothermal fluids. The slip tendency of a surface is defined by the ratio of shear stress to normal stress on that surface: Ts = τ / σn (Morris et al., 1996). Dilation tendency is defined by the stress acting normal to a given surface: Td = (σ1-σn) / (σ1-σ3) (Ferrill et al., 1999). Slip and dilation were calculated using 3DStress (Southwest Research Institute). Slip and dilation tendency are both unitless ratios of the resolved stresses applied to the fault plane by ambient stress conditions. Values range from a maximum of 1, a fault plane ideally oriented to slip or dilate under ambient stress conditions to zero, a fault plane with no potential to slip or dilate. Slip and dilation tendency values were calculated for each fault in the focus study areas at, McGinness Hills, Neal Hot Springs, Patua, Salt Wells, San Emidio, and Tuscarora on fault traces. As dip is not well constrained or unknown for many faults mapped in within these we made these calculations using the dip for each fault that would yield the maximum slip tendency or dilation tendency. As such, these results should be viewed as maximum tendency of each fault to slip or dilate. The resulting along-fault and fault-to-fault variation in slip or dilation potential is a proxy for along fault and fault-to-fault variation in fluid flow conduit potential. Stress Magnitudes and directions Stress field variation within each focus area was approximated based on regional published data and the world stress database (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2010; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012; Moeck et al., 2010; Moos and Ronne, 2010 and Reinecker et al., 2005) as well as local stress information if applicable. For faults within these focus systems we applied either a normal faulting stress regime where the vertical stress (sv) is larger than the maximum horizontal stress (shmax) which is larger than the minimum horizontal stress (sv>shmax>shmin) or strike-slip faulting stress regime where the maximum horizontal stress (shmax) is larger than the vertical stress (sv) which is larger than the minimum horizontal stress (shmax >sv>shmin) depending on the general tectonic province of the system. Based on visual inspection of the limited stress magnitude data in the Great Basin we used magnitudes such that shmin/shmax = .527 and shmin/sv= .46, which are consistent with complete and partial stress field determinations from Desert Peak, Coso, the Fallon area and Dixie valley (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2011; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012). Slip and dilation tendency for the McGinness Hills geothermal field was calculated based on the faults mapped McGinness Hills area (Siler 2012, unpublished). The McGinness Hills area lies in the Basin and Range Province, as such we applied a normal faulting stress regime to the McGinness area faults, with a minimum horizontal stress direction oriented 115, based on inspection of local and regional stress determinations, as explained above. Under these stress conditions north-northeast striking, steeply dipping fault segments have the highest dilation tendency, while north-northeast striking 60° dipping fault segments have the highest tendency to slip. The McGinness Hills geothermal system is characterized by a left-step in a north-northeast striking west-dipping fault system wit...

Distribution, origin and implications of seismic stress release in shallow and intermediate-depth subduction systems

NASA Astrophysics Data System (ADS)

Chen, Po-Fei

A characterization of focal mechanisms is developed for shallow and intermediate-depth earthquakes in the context of the local geometry of subduction systems. Its application to the Ryukyu-Taiwan-Luzon system is used to refine the spatial distribution of characteristic groups of earthquakes in the framework of local tectonic processes, such as flipping of the polarity of subduction and the nascent processes of arc-continent collision. The Harvard catalogue of Centroid Moment Tensor solutions is expanded to include intermediate-depth earthquakes from the WWSSN-HGLP era (1962--1975). Seventy-six new solutions are obtained, with the resulting dataset estimated to be complete for M0 ≥ 1026 dyn-cm. While source mechanisms from our new dataset are generally similar to those previously compiled in the Harvard catalogue, seismic moment release rates are found to be significantly smaller for the WWSSN era. The intermediate-depth seismicity of South America is compiled from the Harvard catalogue, using projection along local slab coordinates, to determine along-strike variations in the distribution of earthquakes and in the geometry of their stress release. Slab geometry is investigated in relation to slab stresses and the presence or absence of arc volcanism. Steeper-dipping slabs are found to exhibit consistent down-dip extension, a higher rate of seismic moment release and surface volcanism. Visualization using slab coordinate projections is extended systematically to a global survey of the geometry of stress release in intermediate-depth earthquakes. Various proposed models for all subduction zones are appraised, as contributors to stress regimes, based on global data compilations. Down-dip stresses, where prominent, are found to be consistent with the thermo-mechanical and petrological force models. Slab-normal conjugate stresses generally support the concept of earthquake reactivation of fossil faults. Patterns of lateral stresses support the predictions of the so-called "punctured-ping-pong-ball" model.

A rapid inoculation technique for assessing pathogenicity of Fusarium oxysporum f. sp. niveum and F. o. melonis on Cucurbits

USGS Publications Warehouse

Freeman, S.; Rodriguez, R.J.

1993-01-01

A continuous-dip inoculation technique for rapid assessment of pathogenicity of Fusarium oxysporum f. sp. niveum and F. o. melonis was developed. The method, adapted from a similar procedure for determining pathogenicity of Colletotrichum magna (causal agent of anthracnose of cucurbits), involves constant exposure of seedlings and cuttings (seedlings with root systems excised) of watermelon and muskmelon to conidial suspensions contained in small scintillation vials. Disease development in intact seedlings corresponded well to disease responses observed with the standard root-dip inoculation/pot assay. The continuous-dip inoculation technique resulted in rapid disease development, with 50% of watermelon cuttings dying after 4–6 days of exposure to F. o. niveum. A mortality of 30% also was observed in watermelon cuttings exposed to conidia of F. o. melonis, as opposed to only a 0–2.5% mortality in seedlings with intact roots. Disease response was similar with muskmelon seedlings and cuttings continuously dip-inoculated with F. o. melonis isolates. However, no disease symptoms were observed in muskmelon seedlings or cuttings inoculated with F. o. niveum. Four nonpathogenic isolates of F. oxysporum did not cause disease symptoms in either watermelon or muskmelon cuttings and seedlings when assayed by this technique. The proposed method enables a rapid screening of pathogenicity and requires less time, labor, and greenhouse space than the standard root-dip inoculation/pot assay. The reliability of the continuous-dip inoculation technique is limited, however, to exposure of intact seedlings at a concentration of 1 × 106conidia per milliliter; the method is not accurate at this range for excised seedlings.

9 CFR 72.13 - Permitted dips and procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Administrator, APHIS. Before a dip will be specifically approved as a permitted dip for the eradication of ticks... effectually eradicate ticks without injury to the animals dipped. (d) Tissue residues; restriction on...

Dip-in Indicators for Visual Differentiation of Fuel Mixtures Based on Wettability of Fluoroalkylchlorosilane-Coated Inverse Opal Films.

PubMed

Sedighi, Abootaleb; Qiu, Shuang; Wong, Michael C K; Li, Paul C H

2015-12-30

We have developed the dip-in indicator based on the inverse opal film (IOF) for visual differentiation of organic liquid mixtures, such as oil/gasoline or ethanol/gasoline fuel mixtures. The IOF consists of a three-dimensional porous structure with a highly ordered periodic arrangement of nanopores. The specularly reflected light at the interface of the nanopores and silica walls contributes to the structural color of the IOF film. This color disappears when the nanopores are infiltrated by a liquid with a similar refractive index to silica. The disappearance of the structural color provides a means to differentiate various liquid fuel mixtures based on their wettability of the nanopores in the IOF-based indicators. For differentiation of various liquid mixtures, we tune the wettability threshold of the indicator in such a way that it is wetted (color disappears) by one liquid but is not wetted by the other (color remains). Although colorimetric differentiation of liquids based on IOF wettability has been reported, differentiation of highly similar liquid mixtures require complicated readout approaches. It is known that the IOF wettability is controlled by multiple surface properties (e.g., oleophobicity) and structural properties (e.g., neck angle and film thickness) of the nanostructure. Therefore, we aim to exploit the combined tuning of these properties for differentiation of fuel mixtures with close compositions. In this study, we have demonstrated that, for the first time, the IOF-based dip-in indicator is able to detect a slight difference in the fuel mixture composition (i.e., 0.4% of oil content). Moreover, the color/no-color differentiation platform is simple, powerful, and easy-to-read. This platform makes the dip-in indicator a promising tool for authentication and determination of fuel composition at the point-of-purchase or point-of-use.

Analysis of Slug Test Response in a Fracture of a Large Dipping Angle

NASA Astrophysics Data System (ADS)

Chen, C.

2013-12-01

A number of cross-borehole slug tests were conducted in a Cenozoic folded sandstone formation, where a fracture has a dipping angle as large as 47°. As all the slug test models available in literature assume the formation to be horizontal, a slug test model taking into account the dipping angle effect is developed herein. Due to the presence of the dipping angle, there is a uniform regional groundwater flow, and the flow field generated by the test is not raidally symmetrical with respect to the test well. When the fracture hydraulic conductivity is relatively low, a larger dipping angle causes larger wellbore flow rates, leading to a faster recovery of the non-oscillatory test response. When the fracture hydraulic conductivity is relatively high, a larger dipping angle causes smaller wellbore heads, resulting in an increase of amplitude of the oscillatory test response; yet little influence on the frequency of oscillation. In general, neglecting the dipping angle may lead to an overestimate of hydraulic conductivity and an underestimate of the storage coefficient. The dipping angle effect is more pronounced for a larger storage coefficient, being less sensitive to transmissivity. An empirical relationship is developed for the minimum dipping angle, smaller than which the dipping angle effect can be safely neglected, as a function of the dimensionless storage coefficient. This empirical relationship helps evaluate whether or not the dipping angle needs to be considered in data analysis. The slug test data in the fracture of a 47°dipping angle is analyzed using the current model, and it is found that neglecting the dip angle can result in a 30% overestimate of transmissivity and a 61% underestimate of the storage coefficient.

Dipping San Andreas and Hayward faults revealed beneath San Francisco Bay, California

USGS Publications Warehouse

Parsons, T.; Hart, P.E.

1999-01-01

The San Francisco Bay area is crossed by several right-lateral strike-slip faults of the San Andreas fault zone. Fault-plane reflections reveal that two of these faults, the San Andreas and Hayward, dip toward each other below seismogenic depths at 60?? and 70??, respectively, and persist to the base of the crust. Previously, a horizontal detachment linking the two faults in the lower crust beneath San Francisco Bay was proposed. The only near-vertical-incidence reflection data available prior to the most recent experiment in 1997 were recorded parallel to the major fault structures. When the new reflection data recorded orthogonal to the faults are compared with the older data, the highest, amplitude reflections show clear variations in moveout with recording azimuth. In addition, reflection times consistently increase with distance from the faults. If the reflectors were horizontal, reflection moveout would be independent of azimuth, and reflection times would be independent of distance from the faults. The best-fit solution from three-dimensional traveltime modeling is a pair of high-angle dipping surfaces. The close correspondence of these dipping structures with the San Andreas and Hayward faults leads us to conclude that they are the faults beneath seismogenic depths. If the faults retain their observed dips, they would converge into a single zone in the upper mantle -45 km beneath the surface, although we can only observe them in the crust.

Involvement of glutamatergic N-methyl-d-aspartate receptors in the expression of increased head-dipping behaviors in the hole-board tests of olfactory bulbectomized mice.

PubMed

Hirose, Noritaka; Saitoh, Akiyoshi; Kamei, Junzo

2016-10-01

Olfactory bulbectomized (OB) mice produce agitated anxiety-like behaviors in the hole-board test, which was expressed by an increase in head-dipping counts and a decrease in head-dipping latencies. However, the associated mechanisms remain unclear. In the present study, MK-801 (10, 100μg/kg), a selective N-methyl-d-aspartate (NMDA) receptor antagonist, significantly and dose-dependently suppressed the increased head-dipping behaviors in OB mice, without affecting sham mice. Similar results were obtained with another selective NMDA receptor antagonist D-AP5 treatment in OB mice. On the other hand, muscimol, a selective aminobutyric acid type A (GABAA) receptor agonist produced no effects on these hyperemotional behaviors in OB mice at a dose (100μg/kg) that produced anxiolytic-like effects in sham mice. Interestingly, glutamine contents and glutamine/glutamate ratios were significantly increased in the amygdala and frontal cortex of OB mice compared to sham mice. Based on these results, we concluded that the glutamatergic NMDA receptors are involved in the expression of increased head-dipping behaviors in the hole-board tests of OB mice. Accordingly, the changes in glutamatergic transmission in frontal cortex and amygdala may play important roles in the expression of these abnormal behaviors in OB mice. Copyright © 2016. Published by Elsevier B.V.

A comparison of radioisotope Brayton and Stirling systems for lunar surface mobile power

NASA Astrophysics Data System (ADS)

Harty, Richard B.

A study was performed by the Rocketdyne Division of Rockwell International on a 2.5-kWe modular dynamic isotope power system (DIPS) using a Stirling power conversion system. The results of this study were compared with similar results performed under the DIPS program using a Brayton power conversion system. The application considered was for lunar mobile power sources in the power range of 2.5 kWe to 15 kWe. The study indicated that the Stirling power module has 20 percent lower mass and 40 percent lower radiator area than the Brayton module. However, the study also revealed that because the Stirling power module requires a complex heat pipe arrangement to transport heat from the isotope to the Stirling heater head and a pumped NaK heat rejection loop, the Stirling module is much more difficult to integrate with the isotope heat source and heat rejection system.

The Origin of X-ray Emission from the Enigmatic Be Star γ Cassiopeiae

NASA Astrophysics Data System (ADS)

Hamaguchi, K.; Oskinova, L.; Russell, C. M. P.; Petre, R.; Enoto, T.; Morihana, K.; Ishida, M.

2017-11-01

Gamma Cassiopeiae is an enigmatic Be star with unusually hard, strong X-ray emission compared with normal main-sequence B stars. The origin has been debated for decades between two theories: mass accretion onto a hidden compact companion and a magnetic dynamo driven by the star-Be disk differential rotation. There has been no decisive signature found that supports either theory, such as a pulse in X-ray emission or the presence of large-scale magnetic field. In a ~100 ksec duration observation of the star with the Suzaku X-ray observatory in 2011, we detected six rapid X-ray spectral hardening events called ``softness dips''. All the softness dip events show symmetric softness ratio variations, and some of them have flat bottoms apparently due to saturation. The softness dip spectra are best described by either ~40% or ~70% partial covering absorption to kT ~12 keV plasma emission by matter with a neutral hydrogen column density of ~2 - 8 × 1021cm-2, while the spectrum outside of these dips is almost free of absorption. This result suggests that two distinct X-ray emitting spots in the γ Cas system, perhaps on a white dwarf companion with dipole mass accretion, are occulted by blobs in the Be stellar wind, the Be disk, or rotating around the white dwarf companion. The formation of a Be star and white dwarf binary system requires mass transfer between two stars; γ Cas may have experienced such activity in the past.

Resource targets for advanced underground coal extraction systems

NASA Technical Reports Server (NTRS)

Hoag, J. H.; Whipple, D. W.; Habib-Agahi, H.; Lavin, M. L.

1982-01-01

Resource targets appropriate for federal sponsorship of research and development of advanced underground coal mining systems are identified. A comprehensive examination of conventional and unconventional coals with particular attention to exceptionally thin and thick seams, steeply dipping beds, and multiple seam geometry was made. The results indicate that the resource of primary importance is flat lying bituminous coal of moderate thickness, under moderate cover, and located within the lower 48 states. Resources of secondary importance are the flat lying multiple seams and thin seams (especially those in Appalachia). Steeply dipping coals, abandoned pillars, and exceptionally thick western coals may be important in some regions of subregions, but the limited tonnage available places them in a position of tertiary importance.

Evaluation of Water Residence Time, Submarine Groundwater Discharge, and Maximum New Production Supported by Groundwater Borne Nutrients in a Coastal Upwelling Shelf System

NASA Astrophysics Data System (ADS)

Luo, Xin; Jiao, Jiu Jimmy; Liu, Yi; Zhang, Xiaolang; Liang, Wenzhao; Tang, Danling

2018-01-01

The biogeochemical processes in the continental shelf systems are usually extensively influenced by coastal upwelling and submarine groundwater discharge (SGD). Using eastern Hainan upwelling shelf system as an example, this study fully investigates SGD and coastal upwelling and their effects on the coastal nutrient loadings to the mixing layer of eastern Hainan shelf. Based on the spatial distributions of 223Ra and 228Ra, water residence time is estimated to be 16.9 ± 8.9 days. Based on the mass balance models of 226Ra and 228Ra, the total SGD of the eastern Hainan shelf is estimated to be 0.8 × 108 and 1.4 × 108 m3 d-1, respectively. The groundwater borne dissolved inorganic nitrogen (DIN) and dissolved inorganic phosphate (DIP) are estimated to be up to 1121.8 and 20.4 μM m2 d-1. The coastal upwelling delivers 2741.8 μM m2 d-1 DIN and 217.7 μM m2 d-1 DIP into the mixing layer, which are predominant in all the exogenous nutrient inputs. The groundwater borne DIN will support a maximum new production of 7.5 mM C m2 d-1, about up to 24.0% of the total new production in the study area. SGD-derived nutrient could be significant as a missing DIN to support the new production in the mixing layer of eastern Hainan shelf. The findings contribute to a better understanding of biogeochemical processes under the influences of SGD and coastal upwelling in the study area and other similar coastal upwelling systems.

Morphology-dependent resonances of a microsphere-optical fiber system

NASA Astrophysics Data System (ADS)

Griffel, Giora; Arnold, Stephen; Taskent, Dogan; Serpengüzel, Ali; Connolly, John; Morris, Nancy

1996-05-01

Morphology-dependent resonances of microspheres sitting upon an index-matched single-mode fiber half-coupler are excited by a tunable 753-nm distributed-feedback laser. Resonance peaks in the scattering spectra and associated dips in the transmission spectra for the TE and TM modes are observed. We present a new model that describes this interaction in terms of the fiber-sphere coupling coefficient and the microsphere's intrinsic quality factor Q0 . This model enables us to obtain expressions for the finesse and the Q factor of the composite particle-fiber system, the resonance width, and the depth of the dips measured in the transmission spectra. Our model shows that index matching improves the coupling efficiency by more than a factor of 2 compared with that of a non-index-matched system.

Morphology-dependent resonances of a microsphere-optical fiber system.

PubMed

Griffel, G; Arnold, S; Taskent, D; Serpengüzel, A; Connolly, J; Morris, N

1996-05-15

Morphology-dependent resonances of microspheres sitting upon an index-matched single-mode fiber half-coupler are excited by a tunable 753-nm distributed-feedback laser. Resonance peaks in the scattering spectra and associated dips in the transmission spectra for the TE and TM modes are observed. We present a new model that describes this interaction in terms of the fiber-sphere coupling coefficient and the microsphere's intrinsic quality factor Q(0). This model enables us to obtain expressions for the finesse and the Q factor of the composite particle-fiber system, the resonance width, and the depth of the dips measured in the transmission spectra. Our model shows that index matching improves the coupling efficiency by more than a factor of 2 compared with that of a non-index-matched system.

Thermodynamic Study of the Nickel Addition in Zinc Hot-Dip Galvanizing Baths

NASA Astrophysics Data System (ADS)

Pistofidis, N.; Vourlias, G.

2010-01-01

A usual practice during zinc hot-dip galvanizing is the addition of nickel in the liquid zinc which is used to inhibit the Sandelin effect. Its action is due to the fact that the ζ (zeta) phase of the Fe-Zn system is replaced by the Τ (tau) phase of the Fe-Zn-Ni system. In the present work an attempt is made to explain the formation of the Τ phase with thermodynamics. For this reason the Gibbs free energy changes for Τ and ζ phases were calculated. The excess free energy for the system was calculated with the Redlich-Kister polyonyme. From this calculation it was deduced that the Gibbs energy change for the tau phase is negative. As a result its formation is spontaneous.

Collaboration processes and perceived effectiveness of integrated care projects in primary care: a longitudinal mixed-methods study.

PubMed

Valentijn, Pim P; Ruwaard, Dirk; Vrijhoef, Hubertus J M; de Bont, Antoinette; Arends, Rosa Y; Bruijnzeels, Marc A

2015-10-09

Collaborative partnerships are considered an essential strategy for integrating local disjointed health and social services. Currently, little evidence is available on how integrated care arrangements between professionals and organisations are achieved through the evolution of collaboration processes over time. The first aim was to develop a typology of integrated care projects (ICPs) based on the final degree of integration as perceived by multiple stakeholders. The second aim was to study how types of integration differ in changes of collaboration processes over time and final perceived effectiveness. A longitudinal mixed-methods study design based on two data sources (surveys and interviews) was used to identify the perceived degree of integration and patterns in collaboration among 42 ICPs in primary care in The Netherlands. We used cluster analysis to identify distinct subgroups of ICPs based on the final perceived degree of integration from a professional, organisational and system perspective. With the use of ANOVAs, the subgroups were contrasted based on: 1) changes in collaboration processes over time (shared ambition, interests and mutual gains, relationship dynamics, organisational dynamics and process management) and 2) final perceived effectiveness (i.e. rated success) at the professional, organisational and system levels. The ICPs were classified into three subgroups with: 'United Integration Perspectives (UIP)', 'Disunited Integration Perspectives (DIP)' and 'Professional-oriented Integration Perspectives (PIP)'. ICPs within the UIP subgroup made the strongest increase in trust-based (mutual gains and relationship dynamics) as well as control-based (organisational dynamics and process management) collaboration processes and had the highest overall effectiveness rates. On the other hand, ICPs with the DIP subgroup decreased on collaboration processes and had the lowest overall effectiveness rates. ICPs within the PIP subgroup increased in control-based collaboration processes (organisational dynamics and process management) and had the highest effectiveness rates at the professional level. The differences across the three subgroups in terms of the development of collaboration processes and the final perceived effectiveness provide evidence that united stakeholders' perspectives are achieved through a constructive collaboration process over time. Disunited perspectives at the professional, organisation and system levels can be aligned by both trust-based and control-based collaboration processes.

A novel 2,6-diisopropylphenyl-docosahexaenoamide conjugate induces apoptosis in T cell acute lymphoblastic leukemia cell lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Altenburg, Jeffrey D.; Harvey, Kevin A.; McCray, Sharon

2011-07-29

Highlights: {yields} 2,6-Diisopropylphenyl-docosahexaenoamide conjugates (DIP-DHA) inhibits the proliferation of T-cell leukemic cell lines. {yields} DIP-DHA resulted in increased activation of caspase-3, and caspase-7. {yields} DIP-DHA significantly downregulated CXCR4 surface expression. -- Abstract: We have previously characterized the effects of 2,6-diisopropylphenyl-docosahexaenoamide (DIP-DHA) conjugates and their analogs on the proliferation and progression of breast cancer cell lines. For this study, we investigated the effects of the DIP-DHA conjugate on 2 representative T cell acute lymphoblastic leukemia (T-ALL) cell lines: CEM and Jurkat. Treatment of both cell lines with DIP-DHA resulted in significantly greater inhibition of proliferation and induction of apoptosis than thatmore » of parent compounds, 2,6-diisopropylphenol (DIP) or docosahexaenoate (DHA). Treatment of the cells with DIP-DHA resulted in increased activation of caspase-3, and caspase-7. Furthermore, induction of apoptosis in both cell lines was reversed in the presence of a caspase family inhibitor. Treatment with DIP-DHA reduced mitochondrial membrane potential. These observations suggest that the effects are driven by intrinsic apoptotic pathways. DIP-DHA treatment also downregulated surface CXCR4 expression, an important chemokine receptor involved in cancer metastasis that is highly expressed in both CEM and Jurkat cells. In conclusion, our data suggest that the DIP-DHA conjugate exhibits significantly more potent effects on CEM and Jurkat cells than that of DIP or DHA alone. These conjugates have potential use for treatment of patients with T cell acute lymphoblastic leukemia.« less

Two-colour dip spectroscopy of jet-cooled molecules

NASA Astrophysics Data System (ADS)

Ito, Mitsuo

In optical-optical double resonance spectroscopy, the resonance transition from an intermediate state to a final state can be detected by a dip of the signal (fluorescence or ion) associated with the intermediate state. This method probing the signal of the intermediate state may be called `two-colour dip spectroscopy'. Various kinds of two-colour dip spectroscopy such as two-colour fluorescence/ion dip spectroscopy, two-colour ionization dip spectroscopy employing stimulated emission, population labelling spectroscopy and mass-selected ion dip spectroscopy with dissociation were briefly described, paying special attention to their characteristics in excitation, detection and application. They were extensively and successfully applied to jet-cooled large molecules and provided us with new useful information on the energy and dynamics of excited molecules.

Semi-automatic mapping of geological Structures using UAV-based photogrammetric data: An image analysis approach

NASA Astrophysics Data System (ADS)

Vasuki, Yathunanthan; Holden, Eun-Jung; Kovesi, Peter; Micklethwaite, Steven

2014-08-01

Recent advances in data acquisition technologies, such as Unmanned Aerial Vehicles (UAVs), have led to a growing interest in capturing high-resolution rock surface images. However, due to the large volumes of data that can be captured in a short flight, efficient analysis of this data brings new challenges, especially the time it takes to digitise maps and extract orientation data. We outline a semi-automated method that allows efficient mapping of geological faults using photogrammetric data of rock surfaces, which was generated from aerial photographs collected by a UAV. Our method harnesses advanced automated image analysis techniques and human data interaction to rapidly map structures and then calculate their dip and dip directions. Geological structures (faults, joints and fractures) are first detected from the primary photographic dataset and the equivalent three dimensional (3D) structures are then identified within a 3D surface model generated by structure from motion (SfM). From this information the location, dip and dip direction of the geological structures are calculated. A structure map generated by our semi-automated method obtained a recall rate of 79.8% when compared against a fault map produced using expert manual digitising and interpretation methods. The semi-automated structure map was produced in 10 min whereas the manual method took approximately 7 h. In addition, the dip and dip direction calculation, using our automated method, shows a mean±standard error of 1.9°±2.2° and 4.4°±2.6° respectively with field measurements. This shows the potential of using our semi-automated method for accurate and efficient mapping of geological structures, particularly from remote, inaccessible or hazardous sites.

[Output characteristics of rainfall runoff phosphorus pollution from a typical small watershed in Yimeng mountainous area].

PubMed

Yu, Xing-xiu; Li, Zhen-wei; Liu, Qian-jin; Jing, Guang-hua

2012-08-01

Relationships between phosphorus pollutant concentrations and precipitation-runoff were analyzed by monitoring pollutant losses at outlets of the Menglianggu watershed in 2010. A typical small watershed was selected to examine the runoff and quality parameters such as total phosphorus (TP), particle phosphorus (PP), dissolve phosphorus (DP) and dissolve inorganic phosphorus (DIP) in rainfall-runoff of 10 rainfall events. Precipitation was above 2 mm for all the 10 rainfall events. The results showed that the peak of phosphorus concentrations occurred before the peak of water flows, whereas change processes of the phosphorus fluxes were consistent with that of the water flows and the phosphorus flux also have a strong linear relationship with the water flows. The minimums of the phosphorus concentrations in every 10 natural rainfall events have small differences with each other, but the maximum and EMCs of the phosphorus concentrations have significant differences with each rainfall event. This was mainly influenced by the precipitation, maximum rainfall intensity and mean rainfall intensity (EMCs) and was less influenced by rainfall duration. DP and TP were mainly composed of DIP and PP, respectively. There were no significant correlations between DIP/DP dynamic changes and rainfall characteristics, whereas significant correlations between PP/TP dynamic changes and maximum rainfall intensity were detected. The production of DIP, DP, AND TP were mainly influenced by the direct runoff (DR) and base flow (BF). The EMCs of DIP, DP, TP and the variations of DIP/DP were all found to have significant polynomial relationships with DR/TR., but the dynamic changes of PP/ TP and the EMCS of PP were less influenced by the DR/TR.

Terahertz wave techniques using a metal mesh for evaluating the components of the stratum corneum.

PubMed

Mizukoshi, Koji; Yonekura, Kazuki; Ogura, Hidehiro; Guan, Yu; Kawase, Kodo

2013-02-01

Terahertz waves are located in the region of the spectrum between milliwaves and infrared. We analyzed the feasibility of terahertz spectroscopy to inspect the compositional variations of the stratum corneum (SC). We used a terahertz time-domain spectroscopy system with the metal mesh technique. To investigate whether terahertz can inspect compositional variation of SC, we measured the terahertz frequency spectra of the SC sheet that was treated with chloroform-methanol, lipid mixture, a denaturation agent, and heating with hot air. The chloroform-methanol treatment of the SC shifted the dip position, which represents a convex downward shape of the spectra, to a higher frequency. This dip shift was reversed to an untreated position by the dose-dependent application of a lipid mixture. The heating treatment of the SC shifted the dip position to a higher frequency. The same dip shift was also induced by the application of a denaturation agent to the SC. The technique using terahertz waves with a metal mesh is effective because of its simplicity and its high degree of accuracy in detecting the amount of lipid and the protein conformation state. © 2012 John Wiley & Sons A/S.

Constraints on the long-period moment-dip tradeoff for the Tohoku earthquake

USGS Publications Warehouse

Tsai, Victor C.; Hayes, Gavin P.; Duputel, Zacharie

2011-01-01

Since the work of Kanamori and Given (1981), it has been recognized that shallow, pure dip-slip earthquakes excite long-period surface waves such that it is difficult to independently constrain the moment (M0) and the dip (δ) of the source mechanism, with only the product M0 sin(2δ) being well constrained. Because of this, it is often assumed that the primary discrepancies between the moments of shallow, thrust earthquakes are due to this moment-dip tradeoff. In this work, we quantify how severe this moment-dip tradeoff is depending on the depth of the earthquake, the station distribution, the closeness of the mechanism to pure dip-slip, and the quality of the data. We find that both long-period Rayleigh and Love wave modes have moment-dip resolving power even for shallow events, especially when stations are close to certain azimuths with respect to mechanism strike and when source depth is well determined. We apply these results to USGS W phase inversions of the recent M9.0 Tohoku, Japan earthquake and estimate the likely uncertainties in dip and moment associated with the moment- dip tradeoff. After discussing some of the important sources of moment and dip error, we suggest two methods for potentially improving this uncertainty.

Constraints on the long-period moment-dip tradeoff for the Tohoku earthquake

USGS Publications Warehouse

Tsai, V.C.; Hayes, G.P.; Duputel, Z.

2011-01-01

Since the work of Kanamori and Given (1981), it has been recognized that shallow, pure dip-slip earthquakes excite long-period surface waves such that it is difficult to independently constrain the moment (M0) and the dip (??) of the source mechanism, with only the product M0 sin(2??) being well constrained. Because of this, it is often assumed that the primary discrepancies between the moments of shallow, thrust earthquakes are due to this moment-dip tradeoff. In this work, we quantify how severe this moment-dip tradeoff is depending on the depth of the earthquake, the station distribution, the closeness of the mechanism to pure dip-slip, and the quality of the data. We find that both long-period Rayleigh and Love wave modes have moment-dip resolving power even for shallow events, especially when stations are close to certain azimuths with respect to mechanism strike and when source depth is well determined. We apply these results to USGS W phase inversions of the recent M9.0 Tohoku, Japan earthquake and estimate the likely uncertainties in dip and moment associated with the moment-dip tradeoff. After discussing some of the important sources of moment and dip error, we suggest two methods for potentially improving this uncertainty. Copyright 2011 by the American Geophysical Union.

Cardiovascular Autonomic Dysfunction in Patients with Drug-Induced Parkinsonism

PubMed Central

Ryu, Dong-Woo; Oh, Ju-Hee; Lee, Yang-Hyun; Park, Sung-Jin; Jeon, Kipyung; Lee, Jong-Yun; Ho, Seong Hee; So, Jungmin; Im, Jin Hee; Lee, Kwang-Soo

2017-01-01

Background and Purpose Recent studies have shown that several nonmotor symptoms differ between Parkinson's disease (PD) and drug-induced parkinsonism (DIP). However, there have been no reports on cardiovascular autonomic function in DIP, and so this study investigated whether cardiovascular autonomic function differs between PD and DIP patients. Methods This study consecutively enrolled 20 DIP patients, 99 drug-naïve PD patients, and 25 age-matched healthy controls who underwent head-up tilt-table testing and 24-h ambulatory blood pressure monitoring. Results Orthostatic hypotension was more frequent in patients with PD or DIP than in healthy controls. In DIP, orthostatic hypotension was associated with the underlying psychiatric diseases and neuroleptics use, whereas prokinetics were not related to orthostatic hypotension. The supine blood pressure, nighttime blood pressure, and nocturnal blood pressure dipping did not differ significantly between the DIP and control groups. Supine hypertension and nocturnal hypertension were more frequent in PD patients than in controls. Conclusions The included DIP patients frequently exhibited orthostatic hypotension that was associated with the underlying diseases as well as the nature of and exposure time to the offending drugs. Clinicians should individualize the manifestations of DIP according to underlying diseases as well as the action mechanism of and exposure time to each offending drug. PMID:27730767

Resonant Raman spectra of diindenoperylene thin films

NASA Astrophysics Data System (ADS)

Scholz, R.; Gisslén, L.; Schuster, B.-E.; Casu, M. B.; Chassé, T.; Heinemeyer, U.; Schreiber, F.

2011-01-01

Resonant and preresonant Raman spectra obtained on diindenoperylene (DIP) thin films are interpreted with calculations of the deformation of a relaxed excited molecule with density functional theory (DFT). The comparison of excited state geometries based on time-dependent DFT or on a constrained DFT scheme with observed absorption spectra of dissolved DIP reveals that the deformation pattern deduced from constrained DFT is more reliable. Most observed Raman peaks can be assigned to calculated A_g-symmetric breathing modes of DIP or their combinations. As the position of one of the laser lines used falls into a highly structured absorption band, we have carefully analyzed the Raman excitation profile arising from the frequency dependence of the dielectric tensor. This procedure gives Raman cross sections in good agreement with the observed relative intensities, both in the fully resonant and in the preresonant case.

Resonant Raman spectra of diindenoperylene thin films.

PubMed

Scholz, R; Gisslén, L; Schuster, B-E; Casu, M B; Chassé, T; Heinemeyer, U; Schreiber, F

2011-01-07

Resonant and preresonant Raman spectra obtained on diindenoperylene (DIP) thin films are interpreted with calculations of the deformation of a relaxed excited molecule with density functional theory (DFT). The comparison of excited state geometries based on time-dependent DFT or on a constrained DFT scheme with observed absorption spectra of dissolved DIP reveals that the deformation pattern deduced from constrained DFT is more reliable. Most observed Raman peaks can be assigned to calculated A(g)-symmetric breathing modes of DIP or their combinations. As the position of one of the laser lines used falls into a highly structured absorption band, we have carefully analyzed the Raman excitation profile arising from the frequency dependence of the dielectric tensor. This procedure gives Raman cross sections in good agreement with the observed relative intensities, both in the fully resonant and in the preresonant case.

Synthesis and Crystal Structure of Dibromido{2-[(4-tert-butylmethylphenyl) iminomethyl]pyridine-κ2 N, N'}Zinc

NASA Astrophysics Data System (ADS)

Khalaj, M.; Ghazanfarpour-Darjani, M.; Seftejani, F. B.; Lalegani, A.

2017-12-01

The title compound [Zn( dip)Br2] was synthesized using the Schiff base bidentate ligand (E)-4- tert-butyl- N-(pyridine-2-ylmethylene)benzeneamine ( dip) and zinc(II) bromide salts. It has been characterized by elemental analysis, X-ray diffraction, and optical spectroscopy. The X-ray diffraction analysis demonstrates that in this structure, the zinc(II) ion is located on an inversion center and exhibits a ZnN2Br2 tetrahedral geometry. In this structure the dip ligand is coordinated with zinc(II) ion in a cyclic-bidentate fashion forming a five-membered metallocyclic ring. The compound crystallizes in the monoclinic sp. gr. P21/ m with a = 9.2700(13) Å, b = 7.6128(11) Å, c = 12.3880(17) Å, and β = 97.021(3)°.

Hunting for shallow slow-slip events at Cascadia

NASA Astrophysics Data System (ADS)

Tan, Y. J.; Bletery, Q.; Fan, W.; Janiszewski, H. A.; Lynch, E.; McCormack, K. A.; Phillips, N. J.; Rousset, B.; Seyler, C.; French, M. E.; Gaherty, J. B.; Regalla, C.

2017-12-01

The discovery of slow earthquakes at subduction zones is one of the major breakthroughs of Earth science in the last two decades. Slow earthquakes involve a wide spectrum of fault slip behaviors and seismic radiation patterns, such as tremor, low-frequency earthquakes, and slow-slip events. The last of these are particularly interesting due to their large moment releases accompanied by minimal ground shaking. Slow-slip events have been reported at various subduction zones ; most of these slow-slip events are located down-dip of the megathrust seismogenic zone, while a few up-dip cases have recently been observed at Nankai and New Zealand. Up-dip slow-slip events illuminate the structure of faulting environments and rupture mechanisms of tsunami earthquakes. Their possible presence and location at a particular subduction zone can help assess earthquake and tsunami hazard for that region. However, their typical location distant from the coast requires the development of techniques using offshore instrumentation. Here, we investigate the absolute pressure gauges (APG) of the Cascadia Initiative, a four year amphibious seismic experiment, to search for possible shallow up-dip slow-slip events in the Cascadia subduction zone. These instruments are collocated with ocean bottom seismometers (OBS) and located close to buoys and onshore GPS stations, offering the opportunity to investigate the utility of multiple datasets. Ultimately, we aim to develop a protocol to analyze APG data for offshore shallow slow-slip event detections and quantify uncertainties, with direct applications to understanding the up-dip subduction interface system in Cascadia.

NAViGaTing the Micronome – Using Multiple MicroRNA Prediction Databases to Identify Signalling Pathway-Associated MicroRNAs

PubMed Central

Shirdel, Elize A.; Xie, Wing; Mak, Tak W.; Jurisica, Igor

2011-01-01

Background MicroRNAs are a class of small RNAs known to regulate gene expression at the transcript level, the protein level, or both. Since microRNA binding is sequence-based but possibly structure-specific, work in this area has resulted in multiple databases storing predicted microRNA:target relationships computed using diverse algorithms. We integrate prediction databases, compare predictions to in vitro data, and use cross-database predictions to model the microRNA:transcript interactome – referred to as the micronome – to study microRNA involvement in well-known signalling pathways as well as associations with disease. We make this data freely available with a flexible user interface as our microRNA Data Integration Portal — mirDIP (http://ophid.utoronto.ca/mirDIP). Results mirDIP integrates prediction databases to elucidate accurate microRNA:target relationships. Using NAViGaTOR to produce interaction networks implicating microRNAs in literature-based, KEGG-based and Reactome-based pathways, we find these signalling pathway networks have significantly more microRNA involvement compared to chance (p<0.05), suggesting microRNAs co-target many genes in a given pathway. Further examination of the micronome shows two distinct classes of microRNAs; universe microRNAs, which are involved in many signalling pathways; and intra-pathway microRNAs, which target multiple genes within one signalling pathway. We find universe microRNAs to have more targets (p<0.0001), to be more studied (p<0.0002), and to have higher degree in the KEGG cancer pathway (p<0.0001), compared to intra-pathway microRNAs. Conclusions Our pathway-based analysis of mirDIP data suggests microRNAs are involved in intra-pathway signalling. We identify two distinct classes of microRNAs, suggesting a hierarchical organization of microRNAs co-targeting genes both within and between pathways, and implying differential involvement of universe and intra-pathway microRNAs at the disease level. PMID:21364759

Observing interactions between DNA bases using ion dip spectroscopy.

NASA Astrophysics Data System (ADS)

Vries Mattanjah, De

2002-03-01

We investigate biomolecular building blocks and their clusters with each other and with water on a single molecular level. The motivation is the need to distinguish between intrinsic molecular properties and those that result from the biological environment. This is achieved by a combination of laser desorption and jet cooling, applied to aromatic amino acids, small peptides containing those, purine bases and nucleosides. This approach is coupled with a number of gas phase laser spectroscopic techniques. We will present results for DNA bases guanine, adenine, cytosine, and their derivatives, for which we obtained tautomer selected vibronic spectra. Capitalizing on these results we use these bases as chromophores to study interactions in single base pairs, obtained by formation of clusters of laser desorbed bases in a supersonic beam. For analysis we employ both UV/UV and IR/UV ion-dip spectroscopy, the results of which we compare with ab initio calculations.

29 CFR 1910.124 - General requirements for dipping and coating operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... or exceeds 25% of its LFL. (2) You must ensure that any exhaust air re-circulated from a dipping or... employee enters a dip tank? When an employee enters a dip tank, you must meet the entry requirements of...

The effects of rotational flow, viscosity, thickness, and shape on transonic flutter dip phenomena

NASA Technical Reports Server (NTRS)

Reddy, T. S. R.; Srivastava, Rakesh; Kaza, Krishna Rao V.

1988-01-01

The transonic flutter dip phenomena on thin airfoils, which are employed for propfan blades, is investigated using an integrated Euler/Navier-Stokes code and a two degrees of freedom typical section structural model. As a part of the code validation, the flutter characteristics of the NACA 64A010 airfoil are also investigated. In addition, the effects of artificial dissipation models, rotational flow, initial conditions, mean angle of attack, viscosity, airfoil thickness and shape on flutter are investigated. The results obtained with a Euler code for the NACA 64A010 airfoil are in reasonable agreement with published results obtained by using transonic small disturbance and Euler codes. The two artificial dissipation models, one based on the local pressure gradient scaled by a common factor and the other based on the local pressure gradient scaled by a spectral radius, predicted the same flutter speeds except in the recovery region for the case studied. The effects of rotational flow, initial conditions, mean angle of attack, and viscosity for the Reynold's number studied seem to be negligible or small on the minima of the flutter dip.

Dealloyed Intra-Nanogap Particles with Highly Robust, Quantifiable Surface-Enhanced Raman Scattering Signals for Biosensing and Bioimaging Applications

PubMed Central

2018-01-01

Uniformly controlling a large number of metal nanostructures with a plasmonically enhanced signal to generate quantitative optical signals and the widespread use of these structures for surface-enhanced Raman scattering (SERS)-based biosensing and bioimaging applications are of paramount importance but are extremely challenging. Here, we report a highly controllable, facile selective-interdiffusive dealloying chemistry for synthesizing the dealloyed intra-nanogap particles (DIPs) with a ∼2 nm intragap in a high yield (∼95%) without the need for an interlayer. The SERS signals from DIPs are highly quantitative and polarization-independent with polarized laser sources. Remarkably, all the analyzed particles displayed the SERS enhancement factors (EFs) of ≥1.1 × 108 with a very narrow distribution of EFs. Finally, we show that DIPs can be used as ultrasensitive SERS-based DNA detection probes for detecting 10 aM to 1 pM target concentrations and highly robust, quantitative real-time cell imaging probes for long-term imaging with low laser power and short exposure time. PMID:29532028

Exposure to sheep dip and the incidence of acute symptoms in a group of Welsh sheep farmers.

PubMed Central

Rees, H

1996-01-01

OBJECTIVES: To measure the exposure of a group of farmers to organophosphate pesticide in sheep dip, and to record the incidence of symptoms after exposure. DESIGN: A prospective study of the autumn 1992 dipping period. Working methods were assessed by questionnaire. Absorption of organophosphate pesticide was estimated before, immediately after, and six weeks after dipping by measuring plasma cholinesterase, erythrocyte cholinesterase, and dialkylphosphate urinary metabolites of organophosphates. Symptoms were recorded by questionnaire at the same time as biological monitoring. Possible confounding factors were identified by medical examination of the subjects. SETTING: Three community council electoral wards in Powys, typical of hill sheep farming areas in Wales. SUBJECTS: All (38) men engaged in sheep dipping living in the three community council electoral wards. RESULTS: 23 sheep farmers and one dipping contractor completed the study--a response rate of 63%. A sample of seven men who refused to enter the full study had similar working practices to the 24 subjects. Subjects reported inadequate handling precautions, and significant skin contamination with dip. Two men reported under diluting dip concentrate for use. Both had significant depression of erythrocyte cholinesterase after dipping. This indicated some absorption of organophosphate pesticide--but this did not reach levels usually associated with toxicity. It was not clear whether the symptoms of these two mens were caused by organophosphate exposure. Measurement of dialkylphosphate urinary metabolites in a single specimen of urine voided shortly after the end of dipping could not be correlated with individual exposure. CONCLUSIONS: Sheep dipping is strenuous and dirty work and sheep farmers find it difficult to wear personal protective equipment and avoid skin contamination with dip. In this limited study, farmers did not seem to have significant organophosphate toxicity, despite using inadequate handling precautions. PMID:8664964

The Origin of High-angle Dip-slip Earthquakes at Geothermal Fields in California

NASA Astrophysics Data System (ADS)

Barbour, A. J.; Schoenball, M.; Martínez-Garzón, P.; Kwiatek, G.

2016-12-01

We examine the source mechanisms of earthquakes occurring in three California geothermal fields: The Geysers, Salton Sea, and Coso. We find source mechanisms ranging from strike slip faulting, consistent with the tectonic settings, to dip slip with unusually steep dip angles which are inconsistent with local structures. For example, we identify a fault zone in the Salton Sea Geothermal Field imaged using precisely-relocated hypocenters with a dip angle of 60° yet double-couple focal mechanisms indicate higher-angle dip-slip on ≥75° dipping planes. We observe considerable temporal variability in the distribution of source mechanisms. For example, at the Salton Sea we find that the number of high angle dip-slip events increased after 1989, when net-extraction rates were highest. There is a concurrent decline in strike-slip and strike-slip-normal faulting, the mechanisms expected from regional tectonics. These unusual focal mechanisms and their spatio-temporal patterns are enigmatic in terms of our understanding of faulting in geothermal regions. While near-vertical fault planes are expected to slip in a strike-slip sense, and dip slip is expected to occur on moderately dipping faults, we observe dip slip on near-vertical fault planes. However, for plausible stress states and accounting for geothermal production, the resolved fault planes should be stable. We systematically analyze the source mechanisms of these earthquakes using full moment tensor inversion to understand the constraints imposed by assuming a double-couple source. Applied to The Geysers field, we find a significant reduction in the number of high-angle dip-slip mechanisms using the full moment tensor. The remaining mechanisms displaying high-angle dip-slip could be consistent with faults accommodating subsidence and compaction associated with volumetric strain changes in the geothermal reservoir.

Review of subduction and its association with geothermal system in Sumatera-Java

NASA Astrophysics Data System (ADS)

Ladiba, A. F.; Putriyana, L.; Sibarani, B. br.; Soekarno, H.

2017-12-01

Java and Sumatera have the largest geothermal resources in Indonesia, in which mostly are spatially associated with volcanoes of subduction zones. However, those volcanoes are not distributed in a regular pattern due to the difference of subduction position. Subduction position in java is relatively more perpendicular to the trench than in Sumatera. In addition, Java has a concentration of large productive geothermal field with vapour dominated system in the western part of Java, which may be caused by the various subduction dip along the island. In order to understand the relationship between the subduction process and geothermal system in the subduction zone volcanoes, we examined several kinematic parameters of subduction that potentially relevant to the formation of geothermal system in overriding plate such as slab dip, subduction rate, and direction of subduction. Data and information regarding tectonic setting of Sumatera and Java and productive geothermal field in Sumatera and Java have been collected and evaluated. In conclusion, there are three condition that caused the geothermal fluid to be more likely being in vapour phase, which are: the subduction is in an orthogonal position, the slab dip is high, and rate of subduction is high. Although there are plenty researches of subduction zone volcanoes, only a few of them present information about its formation and implication to the geothermal system. The result of this study may be used as reference in exploration of geothermal field in mutual geologic environment.

Experimental Modeling of Dynamic Shallow Dip-Slip Faulting

NASA Astrophysics Data System (ADS)

Uenishi, K.

2010-12-01

In our earlier study (AGU 2005, SSJ 2005, JPGU 2006), using a finite difference technique, we have conducted some numerical simulations related to the source dynamics of shallow dip-slip earthquakes, and suggested the possibility of the existence of corner waves, i.e., shear waves that carry concentrated kinematic energy and generate extremely strong particle motions on the hanging wall of a nonvertical fault. In the numerical models, a dip-slip fault is located in a two-dimensional, monolithic linear elastic half space, and the fault plane dips either vertically or 45 degrees. We have investigated the seismic wave field radiated by crack-like rupture of this straight fault. If the fault rupture, initiated at depth, arrests just below or reaches the free surface, four Rayleigh-type pulses are generated: two propagating along the free surface into the opposite directions to the far field, the other two moving back along the ruptured fault surface (interface) downwards into depth. These downward interface pulses may largely control the stopping phase of the dynamic rupture, and in the case the fault plane is inclined, on the hanging wall the interface pulse and the outward-moving Rayleigh surface pulse interact with each other and the corner wave is induced. On the footwall, the ground motion is dominated simply by the weaker Rayleigh pulse propagating along the free surface because of much smaller interaction between this Rayleigh and the interface pulse. The generation of the downward interface pulses and corner wave may play a crucial role in understanding the effects of the geometrical asymmetry on the strong motion induced by shallow dip-slip faulting, but it has not been well recognized so far, partly because those waves are not expected for a fault that is located and ruptures only at depth. However, the seismological recordings of the 1999 Chi-Chi, Taiwan, the 2004 Niigata-ken Chuetsu, Japan, earthquakes as well as a more recent one in Iwate-Miyagi Inland, Japan in 2008, for example, seem to support the need for careful mechanical consideration. In this contribution, utilizing two-dimensional dynamic photoelasticity in conjunction with high speed digital cinematography, we try to perform "fully controlled" laboratory experiments of dip-slip faulting and observe the propagation of interface pulses and corner waves mentioned above. A birefringent material containing a (model) dip-slip fault plane is prepared, and rupture is initiated in that material using an Nd:YAG laser system, and the evolution of time-dependent isochromatic fringe patterns (contours of maximum in-plane shear stress) associated with the dynamic process of shallow dip-slip faulting is recorded. Use of Nd:YAG laser pulses, instead of ignition of explosives, for rupture initiation may enhance the safety of laboratory fracture experiments and enable us to evaluate the energy entering the material (and hence the energy balance in the system) more precisely, possibly in a more controlled way.

The emergence of asymmetric normal fault systems under symmetric boundary conditions

NASA Astrophysics Data System (ADS)

Schöpfer, Martin P. J.; Childs, Conrad; Manzocchi, Tom; Walsh, John J.; Nicol, Andrew; Grasemann, Bernhard

2017-11-01

Many normal fault systems and, on a smaller scale, fracture boudinage often exhibit asymmetry with one fault dip direction dominating. It is a common belief that the formation of domino and shear band boudinage with a monoclinic symmetry requires a component of layer parallel shearing. Moreover, domains of parallel faults are frequently used to infer the presence of a décollement. Using Distinct Element Method (DEM) modelling we show, that asymmetric fault systems can emerge under symmetric boundary conditions. A statistical analysis of DEM models suggests that the fault dip directions and system polarities can be explained using a random process if the strength contrast between the brittle layer and the surrounding material is high. The models indicate that domino and shear band boudinage are unreliable shear-sense indicators. Moreover, the presence of a décollement should not be inferred on the basis of a domain of parallel faults alone.

Detection of fractional solitons in quantum spin Hall systems

NASA Astrophysics Data System (ADS)

Fleckenstein, C.; Traverso Ziani, N.; Trauzettel, B.

2018-03-01

We propose two experimental setups that allow for the implementation and the detection of fractional solitons of the Goldstone-Wilczek type. The first setup is based on two magnetic barriers at the edge of a quantum spin Hall system for generating the fractional soliton. If then a quantum point contact is created with the other edge, the linear conductance shows evidence of the fractional soliton. The second setup consists of a single magnetic barrier covering both edges and implementing a long quantum point contact. In this case, the fractional soliton can unambiguously be detected as a dip in the conductance without the need to control the magnetization of the barrier.

3D beam shape estimation based on distributed coaxial cable interferometric sensor

NASA Astrophysics Data System (ADS)

Cheng, Baokai; Zhu, Wenge; Liu, Jie; Yuan, Lei; Xiao, Hai

2017-03-01

We present a coaxial cable interferometer based distributed sensing system for 3D beam shape estimation. By making a series of reflectors on a coaxial cable, multiple Fabry-Perot cavities are created on it. Two cables are mounted on the beam at proper locations, and a vector network analyzer (VNA) is connected to them to obtain the complex reflection signal, which is used to calculate the strain distribution of the beam in horizontal and vertical planes. With 6 GHz swept bandwidth on the VNA, the spatial resolution for distributed strain measurement is 0.1 m, and the sensitivity is 3.768 MHz mɛ -1 at the interferogram dip near 3.3 GHz. Using displacement-strain transformation, the shape of the beam is reconstructed. With only two modified cables and a VNA, this system is easy to implement and manage. Comparing to optical fiber based sensor systems, the coaxial cable sensors have the advantage of large strain and robustness, making this system suitable for structure health monitoring applications.

Comparison of ambulatory blood pressure monitoring and office blood pressure measurements in obese children and adolescents.

PubMed

Renda, Rahime

2018-04-01

Obesity in adults has been related to hypertension and abnormal nocturnal dipping of blood pressure, which are associated with poor cardiovascular and renal outcomes. Here, we aimed to resolve the relationship between the degree of obesity, the severity of hypertension and dipping status on ambulatory blood pressure in obese children. A total 72 patients with primary obesity aged 7 to 18 years (mean: 13.48 ± 3.25) were selected. Patients were divided into three groups based on body mass index (BMİ) Z-score. Diagnosis and staging of ambulatory hypertension based on 24-h blood pressure measurements, obtained from ambulatory blood pressure monitoring. Based on our ambulatory blood pressure data, 35 patients (48.6%) had hypertension, 7 (20%) had ambulatory prehypertension, 21 (60%) had hypertension, and 7 patients (20%) had severe ambulatory hypertension. There was a significant relationship between severity of hypertension and the degree of obesity (p < 0.05). Thirty-one patients (88.6%) had isolated nighttime hypertension, and 53 patients (73.6%) were non-dippers. All systolic blood pressure results and loads were similar between groups. Diastolic and mean arterial blood pressure levels during the night, diastolic blood pressure loads, and heart rate during the day were significantly higher in Group 3 (p < 0.05). Nocturnal non-dipping was not associated with severity of obesity. Obesity was associated with severity of hypertension, higher diastolic blood pressure at night, mean arterial pressure at night, diastolic blood pressure loads and heart rate at day. Increase in BMI Z-score does not a significant impact on daytime blood pressure and nocturnal dipping status.

9 CFR 72.25 - Dipping methods.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either immersion in a...

CSI 2264: Characterizing Young Stars in NGC 2264 With Short-Duration Periodic Flux Dips in Their Light Curves

NASA Astrophysics Data System (ADS)

Stauffer, John; Cody, Ann Marie; McGinnis, Pauline; Rebull, Luisa; Hillenbrand, Lynne A.; Turner, Neal J.; Carpenter, John; Plavchan, Peter; Carey, Sean; Terebey, Susan; Morales-Calderón, María; Alencar, Silvia H. P.; Bouvier, Jerome; Venuti, Laura; Hartmann, Lee; Calvet, Nuria; Micela, Giusi; Flaccomio, Ettore; Song, Inseok; Gutermuth, Rob; Barrado, David; Vrba, Frederick J.; Covey, Kevin; Padgett, Debbie; Herbst, William; Gillen, Edward; Lyra, Wladimir; Medeiros Guimaraes, Marcelo; Bouy, Herve; Favata, Fabio

2015-04-01

We identify nine young stellar objects (YSOs) in the NGC 2264 star-forming region with optical CoRoT light curves exhibiting short-duration, shallow periodic flux dips. All of these stars have infrared excesses that are consistent with their having inner disk walls near the Keplerian co-rotation radius. The repeating photometric dips have FWHMs generally less than 1 day, depths almost always less than 15%, and periods (3 < P < 11 days) consistent with dust near the Keplerian co-rotation period. The flux dips vary considerably in their depth from epoch to epoch, but usually persist for several weeks and, in two cases, were present in data collected in successive years. For several of these stars, we also measure the photospheric rotation period and find that the rotation and dip periods are the same, as predicted by standard “disk-locking” models. We attribute these flux dips to clumps of material in or near the inner disk wall, passing through our line of sight to the stellar photosphere. In some cases, these dips are also present in simultaneous Spitzer IRAC light curves at 3.6 and 4.5 microns. We characterize the properties of these dips, and compare the stars with light curves exhibiting this behavior to other classes of YSOs in NGC 2264. A number of physical mechanisms could locally increase the dust scale height near the inner disk wall, and we discuss several of those mechanisms; the most plausible mechanisms are either a disk warp due to interaction with the stellar magnetic field or dust entrained in funnel-flow accretion columns arising near the inner disk wall. Based on data from the Spitzer and CoRoT missions, as well as the Canada France Hawaii Telescope (CFHT) MegaCam CCD, and the European Southern Observatory Very Large Telescope, Paranal Chile, under program 088.C-0239. The CoRoT space mission was developed and is operated by the French space agency CNES, with participation of ESA’s RSSD and Science Programmes, Austria, Belgium, Brazil, Germany, and Spain. MegaCam is a joint project of CFHT and CEA/DAPNIA, which is operated by the National Research Council (NRC) of Canada, the Institute National des Sciences de l’Univers of the Centre National de la Recherche Scientifique of France, and the University of Hawaii.

Preparation and biocompatibility evaluation of polypropylene mesh coated with electrospinning membrane for pelvic defects repair.

PubMed

Lu, Yao; Fu, Shaoju; Zhou, Shuanglin; Chen, Ge; Zhu, Chaoting; Li, Nannan; Ma, Ying

2018-05-01

Composite mesh with different materials composition could compensate for the drawbacks brought by single component mesh. Coating a membrane layer on the surface of macroporous mesh is a common method for preparing composite medical mesh. Electrospinning and dipping methods were introduced to form the two kinds of membrane-coated PP meshes (electro-mesh and dip-mesh); several properties were measured based on subcutaneous implantation model in rat. The results revealed that continuous tissue ingrowth could be observed for electro-mesh only with evidences of strength increase (electro-mesh: 0 week - 13.1 ± 0.88 N, 2 week - 16.87 ± 1.39 N, 4 week - 22.04 ± 2.05 N) and thickness increase (electro-mesh: 0 week - 0.437 ± 0.023 mm, 2 week - 0.488 ± 0.025 mm, 4 week - 0.576 ± 0.028 mm). However, no tissues were observed for dip-mesh in the first 2 weeks, both on macroscopic level and microscopic level, proved by strength data (dip-mesh: 0 week - 13.36 ± 1.06 N, 2 week - 13.4 ± 1.33 N, 4 week - 18.61 ± 1.89 N) and thickness data (dip-mesh: 0 week - 0.439 ± 0.018 mm, 2 week - 0.439 ± 0.019 mm, 4 week - 0.502 ± 0.032 mm). Electro-mesh had larger surface area decrease (10.74 ± 1.22%) than that of dip-mesh (2.78 ± 0.52%). The adhesion level of electro-mesh (medium adhesion) was also higher than that of dip-mesh (mild adhesion). Even if showing differences in several properties, both meshes were similar under histological observation, with the ability to support fresh tissues ingrowth. Considering operation environment, electro-mesh seems more suitable than dip-mesh with a rapid tissue growing, medium adhesion rate for repairing pelvic floor defects. Copyright © 2018 Elsevier Ltd. All rights reserved.

Role of the DIP Molecules in DCC Signaling

DTIC Science & Technology

2001-03-01

DIP13 interacts with AKT , a key molecule for cell survival. Our results suggest that the DCC apoptotic signal is mediated by DIP13 that interferes with... AKT cell survival pathway, resulting in cell death. Finally, we have cloned DIP13 beta, suggesting that DIP13 represents a family of molecules with at...interacts with DCC through its PTB domain (Fig. 4). Interestingly, Mitsuuchi et al. (1999) identified a gene dubbed APPL that interacts with AKT , a key

Endocytosis of the Aspartic Acid/Glutamic Acid Transporter Dip5 Is Triggered by Substrate-Dependent Recruitment of the Rsp5 Ubiquitin Ligase via the Arrestin-Like Protein Aly2 ▿

PubMed Central

Hatakeyama, Riko; Kamiya, Masao; Takahara, Terunao; Maeda, Tatsuya

2010-01-01

Endocytosis of nutrient transporters is stimulated under various conditions, such as elevated nutrient availability. In Saccharomyces cerevisiae, endocytosis is triggered by ubiquitination of transporters catalyzed by the E3 ubiquitin ligase Rsp5. However, how the ubiquitination is accelerated under certain conditions remains obscure. Here we demonstrate that closely related proteins Aly2/Art3 and Aly1/Art6, which are poorly characterized members of the arrestin-like protein family, mediate endocytosis of the aspartic acid/glutamic acid transporter Dip5. In aly2Δ cells, Dip5 is stabilized at the plasma membrane and is not endocytosed efficiently. Efficient ubiquitination of Dip5 is dependent on Aly2. aly1Δ cells also show deficiency in Dip5 endocytosis, although less remarkably than aly2Δ cells. Aly2 physically interacts in vivo with Rsp5 at its PY motif and also with Dip5, thus serving as an adaptor linking Rsp5 with Dip5 to achieve Dip5 ubiquitination. Importantly, the interaction between Aly2 and Dip5 is accelerated in response to elevated aspartic acid availability. This result indicates that the regulation of Dip5 endocytosis is accomplished by dynamic recruitment of Rsp5 via Aly2. PMID:20956561

Odour identification test and its relation to cardiac 123I‐metaiodobenzylguanidine in patients with drug induced parkinsonism

PubMed Central

Lee, Phil Hyu; Yeo, Seung Hyeon; Yong, Seok Woo; Kim, Yun Joong

2007-01-01

We investigated olfactory function and its relation to cardiac 123I‐metaiodobenzylguanidine (MIBG) uptake in 15 patients with drug induced parkinsonism (DIP). The mean Cross Cultural Smell Identification (CCSI) score was significantly greater in patients with DIP than in those with Parkinson's disease (PD: 6.9 (1.6) vs 4.4 (2.2); p<0.001); however, the mean CCSI score in patients with DIP was not significantly different from controls. One patient with DIP, whose CCSI score was significantly reduced, also exhibited decreased cardiac MIBG uptake. DIP patients with CCSI scores within the normal range had normal cardiac MIBG uptake. Our study suggests that an olfactory function test may be a useful tool for detecting DIP unrelated to PD and for identifying patients with DIP who have subclinical PD. PMID:17557797

Gum arabic based composite edible coating on green chillies

NASA Astrophysics Data System (ADS)

Valiathan, Sreejit; Athmaselvi, K. A.

2018-04-01

Green chillies were coated with a composite edible coating composed of gum arabic (5%), glycerol (1%), thyme oil (0.5%) and tween 80 (0.05%) to preserve the freshness and quality of green chillies and thus reduce the cost of preservation. In the present work, the chillies were coated with the composite edible coating using the dipping method with three dipping times (1, 3 and 5 min). The physicochemical parameters of the coated and control chillies stored at room temperature (28±2ºC) were evaluated at regular intervals of storage. There was a significant difference (p≤0.05) in the physicochemical properties between the control chillies and coated chillies with 1, 3 and 5 min dipping times. The coated green chillies showed significantly (p≤0.05) lower weight loss, phenolic acid production, capsaicin production and significantly (p≤0.05) higher retention of ascorbic acid, total chlorophyll content, colour, firmness and better organoleptic properties. The composite edible coating of gum arabic and thyme oil with 3 min dipping was effective in preserving the desirable physico-chemical and organoleptic properties of the green chillies up to 12 days, compared to the uncoated chillies that had a shelf life of 6 days at room temperature.

Risk assessment and decontamination of Quinalphos under different culinary processes in/on cabbage.

PubMed

Aktar, Md Wasim; Sengupta, Dwaipayan; Purkait, Swarnali; Chowdhury, Ashim

2010-04-01

Quinalphos 20 AF was applied at the rate of 500 and 1,000 g a.i. ha(-1) in cabbage for two consecutive seasons and the samples harvested at intervals of 0 (3 h after application), 2, 4, 6, 8, and 10 days interval after application. The calculated half-life values were 1.27-1.38 days and 1.12-1.24 days for cabbage heads and cropped soil, respectively. The calculated safe waiting period based on field dissipation study was 5.28-6.7 days, which indicated its persistence nature. Thus, to reduce the safe waiting period, efforts were made to decontaminate the Quinalphos residue from cabbage head by various household preparations (viz. washing, cooking, washing plus cooking, salt water dipping, dipping in boiled salt water, dipping in detergent solution, and dipping in boiled detergent solution). Statistical analysis of the data using Duncan's multiple range test revealed that various household processing substantially reduced the residue of Quinalphos in cabbage heads in the range of 27.72-75.01% irrespective of any dose and seasons, but none were able to satisfactorily bring down the residue below the tolerance level of 0.05 mg kg(-1).

Mechanism and Characteristics of Humidity Sensing with Polyvinyl Alcohol-Coated Fiber Surface Plasmon Resonance Sensor.

PubMed

Shao, Yu; Wang, Ying; Cao, Shaoqing; Huang, Yijian; Zhang, Longfei; Zhang, Feng; Liao, Changrui; Wang, Yiping

2018-06-25

A surface plasmon resonance (SPR) sensor based on a side-polished single mode fiber coated with polyvinyl alcohol (PVA) is demonstrated for relative humidity (RH) sensing. The SPR sensor exhibits a resonant dip in the transmission spectrum in ambient air after PVA film coating, and the resonant wavelength shifts to longer wavelengths as the thickness of the PVA film increases. When RH changes, the resonant dip of the sensor with different film-thicknesses exhibits interesting characteristics for optical spectrum evolution. For sensors with initial wavelengths between 550 nm and 750 nm, the resonant dip shifts to longer wavelengths with increasing RH. The averaged sensitivity increases firstly and then drops, and shows a maximal sensitivity of 1.01 nm/RH%. Once the initial wavelength of the SPR sensor exceeds 850 nm, an inflection point of the resonant wavelength shift can be observed with RH increasing, and the resonant dip shifts to shorter wavelengths for RH values exceeding this point, and sensitivity as high as −4.97 nm/RH% can be obtained in the experiment. The sensor is expected to have potential applications in highly sensitive and cost effective humidity sensing.

Evaluation of dip and spray coating techniques in corrosion inhibition of AA2024 alloy using a silicon/zirconium sol-gel film as coating

NASA Astrophysics Data System (ADS)

Garcia, R. B. R.; Silva, F. S.; Kawachi, E. Y.

2017-02-01

For corrosion protection of aluminum alloy AA2024 -T3 a silicon/zirconium films were obtained via sol-gel process, prepared from tetraethoxysilane and zirconium acetate, in acid medium with a 5 wt% of nonionic surfactant in order to replace the pre-treatment based on chromium conversion coatings. A homogeneous film was obtained and deposited, at low viscosity condition of the sol (˜10cP), by dip and spray coating techniques. The films morphology was evaluated by Scanning Electron Microscopy (SEM), and to know more about the used deposition methodology, the deposited mass and the film thickness were measured. The corrosion protection efficiency of deposited films was evaluated by potentiodynamic polarization. The film deposition by both dip and spray coatings were effective for the deposition of a homogeneous film layer, and the results showed the thickness is directly related with the deposited mass, and the film deposited by spray technique presented the lower value. Potentiodynamic polarization indicated that the film deposited by spray coating apparently has a better inert ceramic film due the polarization resistance increased around 57% against 27 and 14% of dip coating samples (4 and 1 layer, respectively).

Dip Spectroscopy of the Low Mass X-Ray Binary XB 1254-690

NASA Technical Reports Server (NTRS)

Smale, Alan P.; Church, M. J.; BalucinskaChurch, M.; White, Nicholas E. (Technical Monitor)

2002-01-01

We observed the low mass X-ray binary XB 1254-690 with the Rossi X-ray Timing Explorer in 2001 May and December. During the first observation strong dipping on the 3.9-hr orbital period and a high degree of variability were observed, along with "shoulders" approx. 15% deep during extended intervals on each side of the main dips. The first observation also included pronounced flaring activity. The non-dip spectrum obtained using the PCA instrument was well-described by a two-component model consisting of a blackbody with kT = 1.30 +/- 0.10 keV plus a cut-off power law representation of Comptonized emission with power law photon index 1.10 +/- 0.46 and a cut-off energy of 5.9(sup +3.0, sub -1.4) keV. The intensity decrease in the shoulders of dipping is energy-independent, consistent with electron scattering in the outer ionized regions of the absorber. In deep dipping the depth of dipping reached 100%, in the energy band below 5 keV, indicating that all emitting regions were covered by absorber. Intensity-selected dip spectra were well-fit by a model in which the point-like blackbody is rapidly covered, while the extended Comptonized emission is progressively overlapped by the absorber, with the, covering fraction rising to 95% in the deepest portion of the dip. The intensity of this component in the dip spectra could be modeled by a combination of electron scattering and photoelectric absorption. Dipping did not occur during the 2001 December observation, but remarkably, both bursting and flaring were observed contemporaneously.

Hydrogeology and simulation of ground-water flow at the Gettysburg Elevator Plant Superfund Site, Adams County, Pennsylvania

USGS Publications Warehouse

Low, Dennis J.; Goode, Daniel J.; Risser, Dennis W.

2000-01-01

Ground water in Triassic-age sedimentary fractured-rock aquifers in the area of Gettysburg, Pa., is used as drinking water and for industrial and commercial supply. In 1983, ground water at the Gettysburg Elevator Plant was found by the Pennsylvania Department of Environmental Resources to be contaminated with trichloroethene, 1,1,1-trichloroethane, and other synthetic organic compounds. As part of the U.S. Environmental Protection Agency?s Comprehensive Environmental Response, Compensation, and Liability Act, 1980 process, a Remedial Investigation was completed in July 1991, a method of site remediation was issued in the Record of Decision dated June 1992, and a Final Design Report was completed in May 1997. In cooperation with the U.S. Environmental Protection Agency in the hydrogeologic assessment of the site remediation, the U.S. Geological Survey began a study in 1997 to determine the effects of the onsite and offsite extraction wells on ground-water flow and contaminant migration from the Gettysburg Elevator Plant. This determination is based on hydrologic and geophysical data collected from 1991 to 1998 and on results of numerical model simulations of the local ground-water flow-system. The Gettysburg Elevator Site is underlain by red, green, gray, and black shales of the Heidlersburg Member of the Gettysburg Formation. Correlation of natural-gamma logs indicates the sedimentary rock strike about N. 23 degrees E. and dip about 23 degrees NW. Depth to bedrock onsite commonly is about 6 feet but offsite may be as deep as 40 feet. The ground-water system consists of two zones?a thin, shallow zone composed of soil, clay, and highly weathered bedrock and a thicker, nonweathered or fractured bedrock zone. The shallow zone overlies the bedrock zone and truncates the dipping beds parallel to land surface. Diabase dikes are barriers to ground-water flow in the bedrock zone. The ground-water system is generally confined or semi-confined, even at shallow depths. Depth to water can range from flowing at land surface to more than 71 feet below land surface. Potentiometric maps based on measured water levels at the Gettysburg Elevator Plant indicate ground water flows from west to east, towards Rock Creek. Multiple-well aquifer tests indicate the system is heterogeneous and flow is primarily in dipping beds that contain discrete secondary openings separated by less permeable beds. Water levels in wells open to the pumped bed, as projected along the dipping stratigraphy, are drawn down more than water levels in wells not open to the pumped bed. Ground-water flow was simulated for steady-state conditions prior to pumping and long-term average pumping conditions. The three-dimensional numerical flow model (MODFLOW) was calibrated by use of a parameter estimation program (MODFLOWP). Steady-state conditions were assumed for the calibration period of 1996. An effective areal recharge rate of 7 inches was used in model calibration. The calibrated flow model was used to evaluate the effectiveness of the current onsite and offsite extraction well system. The simulation results generally indicate that the extraction system effectively captures much of the ground-water recharge at the Gettysburg Elevator Plant and, hence, contaminated ground-water migrating from the site. Some of the extraction wells pump at low rates and have very small contributing areas. Results indicate some areal recharge onsite will move to offsite extraction wells.

9 CFR 73.10 - Permitted dips; substances allowed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... follows: (1) Lime-sulphur dip, other than proprietary brands thereof, made in the proportion of 12 pounds of unslaked lime (or 16 pounds of commercial hydrated lime, not airslaked lime) and 24 pounds of... of lime-sulphur dip. (2) Dips made from specifically permitted proprietary brand emulsions of...

9 CFR 72.25 - Dipping methods.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... CATTLE § 72.25 Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either...

9 CFR 72.25 - Dipping methods.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... CATTLE § 72.25 Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either...

9 CFR 72.25 - Dipping methods.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... CATTLE § 72.25 Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either...

9 CFR 72.25 - Dipping methods.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Dipping methods. 72.25 Section 72.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... CATTLE § 72.25 Dipping methods. Dipping is accomplished by thoroughly wetting the entire skin by either...

S4. ASYMMETRIC DRUG-INDUCED PARKINSONISM IS RELATED TO PSYCHOPATHOLOGY

PubMed Central

Pieters, Lydia; Bakker, P Roberto; Van Harten, Peter N

2018-01-01

Abstract Background Drug-Induced Parkinsonism (DIP) is the most common movement disorder induced by antipsychotics. The prevalence of DIP in chronic psychiatric populations ranges between 17 and 72% (1–3). Although, DIP is mostly symmetric, asymmetric DIP is reported in 18 to 54% of the patients. (4). There are no studies to the clinical relevance of asymmetric DIP. We investigated the prevalence of motor asymmetry in DIP and its relationship to the severity of psychopathology in a prospective study. Methods In a cohort study of 207 long-stay psychiatric inpatients the prevalence of DIP was assessed at least two times (mean follow-up 1.1 year) in each patient (5). DIP was assessed with the Unified Parkinson Disease Rating Scale (UPDRS) and the prevalence of persistent DIP was 56.2%. Patients with at least one time parkinsonism in the upper/lower limb(s) were included for analyses. Asymmetry of parkinsonism was calculated with the symmetry index (Figure 1). A cut-off value of ≥ 0,20 was used for the definition of asymmetric DIP. Multilevel mixed models were built to explore the relationship between asymmetry in DIP and the severity of psychopathology, measured on the Clinical Global Impression-Schizophrenia scale severity index (CGI-SCH SI). Results In a cohort study of 207 long-stay psychiatric inpatients the prevalence of DIP was assessed at least two times (mean follow-up 1.1 year) in each patient (5). DIP was assessed with the Unified Parkinson Disease Rating Scale (UPDRS) and the prevalence of persistent DIP was 56.2%. Patients with at least one time parkinsonism in the upper/lower limb(s) were included for analyses. Asymmetry of parkinsonism was calculated with the symmetry index (Figure 1). A cut-off value of ≥ 0,20 was used for the definition of asymmetric DIP. Multilevel mixed models were built to explore the relationship between asymmetry in DIP and the severity of psychopathology, measured on the Clinical Global Impression-Schizophrenia scale severity index (CGI-SCH SI). Discussion DIP is asymmetric in 1 of 5 patients. Therefore, the clinical rule that Parkinson’s disease always starts asymmetrically and such may be helpful to differentiate between Parkinson’s disease and DIP is not valid. Asymmetric presentation of DIP is of clinical relevance as it is related to the severity of psychopathology. Asymmetric DIP may alert the clinician of more severe psychopathology. Replication is indicated to examine the robustness of the relationship. References 1. Modestin J, Wehrli MV, Stephan PL, Agarwalla P. Evolution of neuroleptic-induced extrapyramidal syndromes under long-term neuroleptic treatment. Schizophr Res. 2008; 100(1–3): 97–107. 2. Janno S, Holi M, Tuisku K, Wahlbeck K. Prevalence of Neuroleptic-Induced Movement Disorders in Chronic Schizophrenia Inpatients. Am J Psychiatry. 2004; 161(1): 160–163. 3. Harten PN Van, Matroos GE, Hoek HW. The prevalence of tardive dystonia, tardive dyskinesia, parkinsonism and akathisia. The Curaçao Extrapyramidal Syndromes Study I. Schizophr Res. 1996; 19(2): 195–203. 4. Shin H, Chung J. Drug-Induced Parkinsonism. J Clin Neurol. 2012; 8: 15–21. 5. Bakker PR, de Groot IW, van Os J, van Harten PN. Long-Stay Psychiatric Patients: A Prospective Study Revealing Persistent Antipsychotic-Induced Movement Disorder. PLoS One. 2011; 6(10): 1–6.

Synthesis and characterization of thick PZT films via sol-gel dip coating method

NASA Astrophysics Data System (ADS)

Shakeri, Amid; Abdizadeh, Hossein; Golobostanfard, Mohammad Reza

2014-09-01

Thick films of lead zirconate titanate (PZT) offer possibilities for micro-electro-mechanical systems such as high frequency ultrasonic transducers. In this paper, crack-free thick films of PZT have been prepared up to 45 μm thickness via modified sol-gel dip coating method. In this procedure, acetic acid-alcoholic based sol is used by applying diethanolamine (DEA) and deionized water as additives. The effects of DEA and water on the crystal structure and surface morphology of the films are investigated. The mechanisms of acetic acid and DEA complexations are introduced by using FTIR spectrometer which illustrates suitable substitution of complexing agents with alkoxide groups. DEA/(Ti + Zr) = 0.5 or water/(Ti + Zr) = 0.5 are determined as the optimum molar ratio of additives, which lead to the formation of almost pure perovskite phase with the tetragonal lattice parameters of ct = 4.16 Ǻ and at = 4.02 Ǻ and a distortion of 2%. Values of remanent polarization and dielectric constant of 7.8 μC cm-2 and 1630 were obtained for 45 μm thick films, respectively.

Homogeneous PCBM layers fabricated by horizontal-dip coating for efficient bilayer heterojunction organic photovoltaic cells.

PubMed

Huh, Yoon Ho; Bae, In-Gon; Jeon, Hong Goo; Park, Byoungchoo

2016-10-31

We herein report a homogeneous [6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) layer, produced by a solution process of horizontal-dipping (H-dipping) to improve the photovoltaic (PV) effects of bilayer heterojunction organic photovoltaic cells (OPVs) based on a bi-stacked poly(3-hexylthiophene) (P3HT) electron donor layer and a PCBM electron acceptor layer (P3HT/PCBM). It was shown that a homogeneous and uniform coating of PCBM layers in the P3HT/PCBM bilayer OPVs resulted in reliable and reproducible device performance. We recorded a power conversion efficiency (PCE) of 2.89%, which is higher than that (2.00%) of bilayer OPVs with a spin-coated PCBM layer. Moreover, introducing surfactant additives of poly(oxyethylene tridecyl ether) (PTE) into the homogeneous P3HT/PCBM PV layers resulted in the bilayer OPVs showing a PCE value of 3.95%, which is comparable to those of conventional bulk-heterojunction (BHJ) OPVs (3.57-4.13%) fabricated by conventional spin-coating. This improved device performance may be attributed to the selective collection of charge carriers at the interfaces among the active layers and electrodes due to the PTE additives as well as the homogeneous formation of the functional PCBM layer on the P3HT layer. Furthermore, H-dip-coated PCBM layers were deposited onto aligned P3HT layers by a rubbing technique, and the rubbed bilayer OPV exhibited improved in-plane anisotropic PV effects with PCE anisotropy as high as 1.81, which is also higher than that (1.54) of conventional rubbed BHJ OPVs. Our results suggest that the use of the H-dip-coating process in the fabrication of PCBM layers with the PTE interface-engineering additive could be of considerable interest to those seeking to improve PCBM-based opto-electrical organic thin-film devices.

Characteristics of the Roof Behaviors and Mine Pressure Manifestations During the Mining of Steep Coal Seam

NASA Astrophysics Data System (ADS)

Hong-Sheng, Tu; Shi-Hao, Tu; Cun, Zhang; Lei, Zhang; Xiao-Gang, Zhang

2017-12-01

A steep seam similar simulation system was developed based on the geological conditions of a steep coal seam in the Xintie Coal Mine. Basing on similar simulation, together with theoretical analysis and field measurement, an in-depth study was conducted to characterize the fracture and stability of the roof of steep working face and calculate the width of the region backfilled with gangue in the goaf. The results showed that, as mining progressed, the immediate roof of the steep face fell upon the goaf and backfilled its lower part due to gravity. As a result, the roof in the lower part had higher stability than the roof in the upper part of the working face. The deformation and fracture of main roof mainly occurred in the upper part of the working face; the fractured main roof then formed a "voussoir beam" structure in the strata's dip direction, which was subjected to the slip- and deformation-induced instability. The stability analysis indicated that, when the dip angle increased, the rock masses had greater capacity to withstand slip-induced instability but smaller capacity to withstand deformation-induced instability. Finally, the field measurement of the forces exerted on the hydraulic supports proved the characteristics of the roof's behaviors during the mining of a steep seam.

Numerical analysis of the effects induced by normal faults and dip angles on rock bursts

NASA Astrophysics Data System (ADS)

Jiang, Lishuai; Wang, Pu; Zhang, Peipeng; Zheng, Pengqiang; Xu, Bin

2017-10-01

The study of mining effects under the influences of a normal fault and its dip angle is significant for the prediction and prevention of rock bursts. Based on the geological conditions of panel 2301N in a coalmine, the evolution laws of the strata behaviors of the working face affected by a fault and the instability of the fault induced by mining operations with the working face of the footwall and hanging wall advancing towards a normal fault are studied using UDEC numerical simulation. The mechanism that induces rock burst is revealed, and the influence characteristics of the fault dip angle are analyzed. The results of the numerical simulation are verified by conducting a case study regarding the microseismic events. The results of this study serve as a reference for the prediction of rock bursts and their classification into hazardous areas under similar conditions.

Process for Making Ceramic Mold

NASA Technical Reports Server (NTRS)

Buck, Gregory M. (Inventor); Vasquez, Peter (Inventor)

2001-01-01

An improved process for slip casting molds that can be more economically automated and that also exhibits greater dimensional stability is disclosed. The process involves subjecting an investment pattern, preferably made from wax, to successive cycles of wet-dipping in a slurry of colloidal, silica-based binder and dry powder-coating, or stuccoing with plaster of Paris or calcium sulfate mixtures to produce a multi-layer shell over the pattern. The invention as claimed entails applying a primary and a secondary coating to the investment pattern. At least two wet-dipping on in a primary slurry and dry-stuccoing cycles provide the primary coating, and an additional two wet-dippings and dry-stuccoing cycles provide the secondary, or back-up, coating. The primary and secondary coatings produce a multi-layered shell pattern. The multi-layered shell pattern is placed in a furnace first to cure and harden, and then to vaporize the investment pattern, leaving a detailed, high precision shell mold.

The Tranisiting Dust of Boyajian's Star

NASA Astrophysics Data System (ADS)

Bodman, Eva; Ellis, Tyler G.; Boyajian, Tabetha S.; Wright, Jason

2018-06-01

From May to October of 2017, Boyajian's Star displayed four days-long dips in observed flux, which are referred to as “Elsie,” “Celeste,” “Skara Brae,” and “Angkor” (Boyajian et al. 2018). This Elsie family dip event was monitored with the Las Cumbres Observatory in three bands, B, r', and i'. Looking at each dip individually, we analyze the multi-band photometry for wavelength dependency in dip depth to constrain properties of the transiting material. We find that all of the dips show non-grey extinction and are consistent with optically thin dust. Interpreting the dips as transiting dust clouds, we constrain the properties of the dust grains and find that the average grain radius is <1 micron, assuming silicate composition. This wavelength dependency and grain size is inconsistent with observed properties of the long-term “secular” dimming (Meng et al. 2017), suggesting that the dust causing the dips is from a separate population.

The role of thin, mechanical discontinuities on the propagation of reverse faults: insights from analogue models

NASA Astrophysics Data System (ADS)

Bonanno, Emanuele; Bonini, Lorenzo; Basili, Roberto; Toscani, Giovanni; Seno, Silvio

2016-04-01

Fault-related folding kinematic models are widely used to explain accommodation of crustal shortening. These models, however, include simplifications, such as the assumption of constant growth rate of faults. This value sometimes is not constant in isotropic materials, and even more variable if one considers naturally anisotropic geological systems. , This means that these simplifications could lead to incorrect interpretations of the reality. In this study, we use analogue models to evaluate how thin, mechanical discontinuities, such as beddings or thin weak layers, influence the propagation of reverse faults and related folds. The experiments are performed with two different settings to simulate initially-blind master faults dipping at 30° and 45°. The 30° dip represents one of the Andersonian conjugate fault, and 45° dip is very frequent in positive reactivation of normal faults. The experimental apparatus consists of a clay layer placed above two plates: one plate, the footwall, is fixed; the other one, the hanging wall, is mobile. Motor-controlled sliding of the hanging wall plate along an inclined plane reproduces the reverse fault movement. We run thirty-six experiments: eighteen with dip of 30° and eighteen with dip of 45°. For each dip-angle setting, we initially run isotropic experiments that serve as a reference. Then, we run the other experiments with one or two discontinuities (horizontal precuts performed into the clay layer). We monitored the experiments collecting side photographs every 1.0 mm of displacement of the master fault. These images have been analyzed through PIVlab software, a tool based on the Digital Image Correlation method. With the "displacement field analysis" (one of the PIVlab tools) we evaluated, the variation of the trishear zone shape and how the master-fault tip and newly-formed faults propagate into the clay medium. With the "strain distribution analysis", we observed the amount of the on-fault and off-fault deformation with respect to the faulting pattern and evolution. Secondly, using MOVE software, we extracted the positions of fault tips and folds every 5 mm of displacement on the master fault. Analyzing these positions in all of the experiments, we found that the growth rate of the faults and the related fold shape vary depending on the number of discontinuities in the clay medium. Other results can be summarized as follows: 1) the fault growth rate is not constant, but varies especially while the new faults interacts with precuts; 2) the new faults tend to crosscut the discontinuities when the angle between them is approximately 90°; 3) the trishear zone change its shape during the experiments especially when the main fault interacts with the discontinuities.

Environmental and ice volume changes based on seismic stratigraphy in Sabrina Coast, East Antarctica: Preliminary results from NBP1402

NASA Astrophysics Data System (ADS)

Gulick, S. P. S.; Fernandez-Vasquez, R. A.; Frederick, B.; Saustrup, S., Sr.; Domack, E. W.; Lavoie, C.; Shevenell, A.; Blankenship, D. D.; Leventer, A.

2014-12-01

In 2014, the R/V Nathaniel B. Palmer (NBP1402) sailed to a virtually unexplored continental shelf along the Sabrina Coast, East Antarctica. The shelf contains the sedimentary record of environmental and ice volume changes within the Aurora Subglacial Basin (ASB), which is presently occupied by ~7 m sea level-rise equivalent of ice. We acquired 750 km of high-resolution seismic data proximal to the Reynolds Trough and Moscow University Ice Shelf glacial systems west of the Dalton Ice Tongue using dual 45/45 cu. in. G.I. guns and a 24 ch. streamer with 3.125 m groups providing a vertical resolution of ~3 m simultaneously with CHIRP data. These are the first images of this margin acquired and show a remarkable set of sequence stratigraphic transitions. Crystalline basement is at the seafloor landward and buried seaward with a transition to smoother reflection interface. Reflective sedimentary strata overlie the basement, dip seaward, and are capped by a landward-dipping regional angular unconformity. Above this are a series of transparent seismic facies that, along with the middle to outer shelf seafloor, dip landward towards a shelf-oblique glacial trough. The older, seaward-dipping strata include a deeper series of units that display at least three stratal architectures interpreted to be shelf deltas implying a pre-glacial, fluvial environment within the drainage basin. Above these sequences, the seismic facies transition to surfaces exhibiting significant erosion, small u-shaped valleys, and channel fill sequences, all of which are reminiscent of temperate glacial features. We interpret these sequences as including sub-ice tunnel valleys and grounding zone wedges with interspersed non-glacial to pro-glacial deposits. Increasing glaciogenic facies upsection suggests a gradual fluvial to glacial transition and increasing glacial extent with time. The subsequent transition to ice sheets is marked by erosion to basement landward and the angular unconformity seaward. The unconformity is overlain by glacial diamict, representing an incomplete record of cold-based glaciations after the ASB became ice-filled. Correlations with cores collected above and below the unconformity and deltaic unit should allow us to determine the ages of these transitions from fluvial to polythermal to ice sheets in East Antarctica.

Theoretical study of surface plasmon resonance sensors based on 2D bimetallic alloy grating

NASA Astrophysics Data System (ADS)

Dhibi, Abdelhak; Khemiri, Mehdi; Oumezzine, Mohamed

2016-11-01

A surface plasmon resonance (SPR) sensor based on 2D alloy grating with a high performance is proposed. The grating consists of homogeneous alloys of formula MxAg1-x, where M is gold, copper, platinum and palladium. Compared to the SPR sensors based a pure metal, the sensor based on angular interrogation with silver exhibits a sharper (i.e. larger depth-to-width ratio) reflectivity dip, which provides a big detection accuracy, whereas the sensor based on gold exhibits the broadest dips and the highest sensitivity. The detection accuracy of SPR sensor based a metal alloy is enhanced by the increase of silver composition. In addition, the composition of silver which is around 0.8 improves the sensitivity and the quality of SPR sensor of pure metal. Numerical simulations based on rigorous coupled wave analysis (RCWA) show that the sensor based on a metal alloy not only has a high sensitivity and a high detection accuracy, but also exhibits a good linearity and a good quality.

[Study on pipe material's influence on chlorine dioxide drinking water disinfection].

PubMed

He, Tao; Yue, Yinling; Ling, Bo; Zhang, Lan

2010-09-01

To study the pipe material's influence on chlorine dioxide drinking water disinfection. 0.8 mg/L chlorine dioxide solution was injected into 5 kinds of pipes respectively, PPR, PVC-U, Steel with Zinc coating, copper and PE pipes. Dipped free from light for 48 hours and the concentrations of chlorine dioxide, chlorite and chlorate were tested from samples taken from each kind of pipe at 1, 2, 3, 4, 5, 6, 12, 24 and 48 hours respectively. Chlorine dioxides decay rates in the water dipping the pipes increase as the dipping time increases and the decay of chlorine dioxide mainly occurs within 6 hours after the dipping. But for different pipe, the influence of decay differs. The consumption of chlorine dioxide of the metal pipes is more than that of the plastic pipes. And with 2 hours after the dipping experiment begins, the concentrations of the chlorite of the copper pipe and of the steel with zinc coating pipe increase quickly and reach the maximum concentration. But then the chlorite concentration decreases greatly. After dipped 24 hours, the chlorite in the water in the pipe can not be detected. For other plastic piples, all the chlorite concentrations in the dipping water increase as the dipping time increase. Compared with the start of the dipping experiment, the chlorate concentration in the dipping water of each pipe has no obvious change. The material of the water transportation pipe does have influence on chlorine dioxide drinking water disinfection.

The addition of a plain or herb-flavored reduced-fat dip is associated with improved preschoolers' intake of vegetables.

PubMed

Savage, Jennifer S; Peterson, Julie; Marini, Michele; Bordi, Peter L; Birch, Leann L

2013-08-01

This quasiexperimental study used a within-subjects experimental design to determine whether adding herbs and/or spices to a reduced-fat dip increased children's willingness to taste, liking of, and consumption of vegetables. Participants were preschool children aged 3 to 5 years who attended a child-care center in Central Pennsylvania in late 2008 and early 2009. First, children's familiarity with and liking of six raw vegetables and five dips (reduced-fat plain, herb, garlic, pizza, and ranch) were assessed. In Experiment 1 (n=34), children tasted a vegetable they liked, one they disliked, and one they refused, with a reduced-fat plain dip and their favorite reduced-fat herb-flavored dip. In Experiment 2 (n=26 or n=27), they rated their liking of celery and yellow squash, with and without their favorite reduced-fat herb dip (pizza or ranch), and their intake of those vegetable snacks was measured. In Experiment 1, the herb-flavored dip was preferred over the plain dip (P<0.01), and children were three times more likely to reject the vegetable alone, compared with eating the vegetable paired with an herb dip (P<0.001). In Experiment 2, children ate significantly more of a previously rejected or disliked vegetable (celery and squash) when offered with a preferred reduced-fat herb dip than when the vegetable was served alone (P<0.05). These findings suggest that offering vegetables with reduced-fat dips containing familiar herb and spice flavors can increase tasting and thereby promote liking, acceptance, and consumption of vegetables, including vegetables previously rejected or disliked. Copyright © 2013 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Return Stroke Current Reflections in Rocket-Triggered Lightning

NASA Astrophysics Data System (ADS)

Caicedo, J.; Uman, M. A.; Jordan, D.; Biagi, C. J.; Hare, B.

2015-12-01

In the six years from 2009 to 2014, there have been eight triggered flashes at the ICLRT, from a total of 125, in which a total of ten return stroke channel-base currents exhibited a dip 3.0 to 16.6 μs after the initial current peak. Close range electric field measurements show a related dip following the initial electric field peak, and electric field derivative measurements show an associated bipolar pulse, confirming that this phenomenon is not an instrumentation effect in the current measurement. For six of the eight flashes, high-speed video frames show what appears to be suspended sections of unexploded triggering wire at heights of about 150 to 300 m that are illuminated when the upward current wave reaches them. The suspended wire can act as an impedance discontinuity, perhaps as it explodes, and cause a downward reflection of some portion of the upward-propagating current wave. This reflected wave travels down the channel and causes the dip in the measured channel-base current when it reaches ground and reflects upward. The modified transmission line model with exponential decay (MTLE) is used to model the close electric field and electric field derivatives of the postulated initial and reflected current waves, starting with the measured channel base current, and the results are compared favorably with measurements made at distances ranging from 92 to 444 m. From the measured time between current impulse initiation and the time the current reflection reaches the channel base and the current dip initiates, along with the reflection height from the video records, we find the average return stroke current speed for each of the ten strokes to be from 0.28 to 1.9×108 ms-1, with an error of ±0.01×108 ms-1 due to a ±0.1 μs uncertainty in the measurement. This represents the first direct measurement of return stroke current speed, all previous return stroke speed measurements being derived from the luminosity of the process.

Global morphology of ionospheric F-layer scintillations using FS3/COSMIC GPS radio occultation data

NASA Astrophysics Data System (ADS)

Tsai, Lung-Chih; Su, Shin-Yi

2016-07-01

The FormoSat-3/ Constellation Observing System for Meteorology, Ionosphere and Climate (FS3/COSMIC) has been proven a successful mission on profiling and modeling of ionospheric electron density by the radio occultation (RO) technique. In this study we report FS3/COSMIC limb-viewing observations of the GPS L-band scintillation since mid 2006 and propose to study F-layer irregularity morphology. Generally the FS3/COSMIC has performed >1000 ionospheric RO observations per day. Most of these observations can provide limb-viewing profiles of S4 scintillation index at dual L-band frequencies. There are a few percentage of FS3/COSMIC RO observations having >0.08 S4 values on average. However, seven identified areas at Central Pacific Area (-20∘~ 20∘dip latitude, 160∘E~130∘W), South American Area (-20∘~ 20∘dip latitude, 100∘W~30∘W), African Area (-20∘~ 20∘dip latitude, 30∘W~50∘E), European Area (30∘~55∘N, 0∘~55∘E), Japan See Area (35∘~55∘N, 120∘~150∘E), Arctic Area (> 65∘dip latitude), and Antarctic Area (< -65∘dip latitude) have been designated to have much higher percentage of strong L-band RO scintillation. During these years in most of the last sunspot cycle from mid 2006 to end 2014 the climatology of scintillations, namely, its variations with each identified area, season, local time, magnetic activity and solar activity have been documented.

FROM X-RAY DIPS TO ECLIPSE: WITNESSING DISK REFORMATION IN THE RECURRENT NOVA U Sco

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ness, J.-U.; Talavera, A.; Gonzalez-Riestra, R.

2012-01-20

The tenth recorded outburst of the recurrent eclipsing nova U Sco was observed simultaneously in X-ray, UV, and optical by XMM-Newton on days 22.9 and 34.9 after the outburst. Two full passages of the companion in front of the nova ejecta were observed, as was the reformation of the accretion disk. On day 22.9, we observed smooth eclipses in UV and optical but deep dips in the X-ray light curve that disappeared by day 34.9, yielding clean eclipses in all bands. X-ray dips can be caused by clumpy absorbing material that intersects the line of sight while moving along highlymore » elliptical trajectories. Cold material from the companion could explain the absence of dips in UV and optical light. The disappearance of X-ray dips before day 34.9 implies significant progress in the formation of the disk. The X-ray spectra contain photospheric continuum emission plus strong emission lines, but no clear absorption lines. Both continuum and emission lines in the X-ray spectra indicate a temperature increase from day 22.9 to day 34.9. We find clear evidence in the spectra and light curves for Thompson scattering of the photospheric emission from the white dwarf. Photospheric absorption lines can be smeared out during scattering in a plasma of fast electrons. We also find spectral signatures of resonant line scattering that lead to the observation of the strong emission lines. Their dominance could be a general phenomenon in high-inclination systems such as Cal 87.« less

Antinociceptive effect of systemically administered dipyrone (metamizol), magnesium chloride or both in a murine model of cancer.

PubMed

Brito, B E; Vazquez, E; Taylor, P; Alvarado, Y; Vanegas, H; Millan, A; Tortorici, V

2017-03-01

Opioid effectiveness to treat cancer pain is often compromised by the development of tolerance and the occurrence of undesirable side effects, particularly during long-term treatment. Hence, the search for more efficient analgesics remains a necessity. The main goal of this study was to relieve neuropathic symptoms associated with tumour growth by administering the non-opioid analgesic dipyrone (DIP) alone or in combination with magnesium chloride (MgCl 2 ), an adjuvant that blocks the NMDA receptor channel. Mice were inoculated with a melanoma cell line (B16-BL6) in the left thigh and two protocols were used to evaluate the effect of DIP (270 mg/kg), MgCl 2 (200 mg/kg), or the combination DIP-MgCl 2 . In the therapeutic protocol the drugs, alone or combined, were administered once tumour had promoted increased nociception. In the preventive protocol, drugs were administered prior to the appearance of the primary tumour. Tumour growth was assessed with a caliper and nociception was determined using behavioural tests. DIP promoted antinociception only at the beginning of both protocols due to the development of tolerance. The combination DIP-MgCl 2 improved the antinociceptive effect, avoiding tolerance and reducing tumour growth in the preventive treatment, more efficiently than each compound alone. These results suggest that DIP-MgCl 2 may represent a safe, affordable and accessible option to reduce tumour growth and to treat cancer pain avoiding the risk of tolerance, without the typical complications of opioids agents, particularly when long-term treatment is required. This study shows a non-opioid analgesic combined with an adjuvant as a therapeutic option to treat cancer pain. The avoidance of antinociceptive tolerance when repeated administration is required, as well as tumor growth reduction, are additional advantages to be considered. © 2016 European Pain Federation - EFIC®.

Implementing a C++ Version of the Joint Seismic-Geodetic Algorithm for Finite-Fault Detection and Slip Inversion for Earthquake Early Warning

NASA Astrophysics Data System (ADS)

Smith, D. E.; Felizardo, C.; Minson, S. E.; Boese, M.; Langbein, J. O.; Guillemot, C.; Murray, J. R.

2015-12-01

The earthquake early warning (EEW) systems in California and elsewhere can greatly benefit from algorithms that generate estimates of finite-fault parameters. These estimates could significantly improve real-time shaking calculations and yield important information for immediate disaster response. Minson et al. (2015) determined that combining FinDer's seismic-based algorithm (Böse et al., 2012) with BEFORES' geodetic-based algorithm (Minson et al., 2014) yields a more robust and informative joint solution than using either algorithm alone. FinDer examines the distribution of peak ground accelerations from seismic stations and determines the best finite-fault extent and strike from template matching. BEFORES employs a Bayesian framework to search for the best slip inversion over all possible fault geometries in terms of strike and dip. Using FinDer and BEFORES together generates estimates of finite-fault extent, strike, dip, preferred slip, and magnitude. To yield the quickest, most flexible, and open-source version of the joint algorithm, we translated BEFORES and FinDer from Matlab into C++. We are now developing a C++ Application Protocol Interface for these two algorithms to be connected to the seismic and geodetic data flowing from the EEW system. The interface that is being developed will also enable communication between the two algorithms to generate the joint solution of finite-fault parameters. Once this interface is developed and implemented, the next step will be to run test seismic and geodetic data through the system via the Earthworm module, Tank Player. This will allow us to examine algorithm performance on simulated data and past real events.

Nuclear reactor sealing system

DOEpatents

McEdwards, James A.

1983-01-01

A liquid metal-cooled nuclear reactor sealing system. The nuclear reactor includes a vessel sealed at its upper end by a closure head. The closure head comprises at least two components, one of which is rotatable; and the two components define an annulus therebetween. The sealing system includes at least a first and second inflatable seal disposed in series in an upper portion of the annulus. The system further includes a dip seal extending into a body of insulation located adjacent a bottom portion of the closure head. The dip seal comprises a trough formed by a lower portion of one of the components, and a seal blade pendently supported from the other component and extending downwardly into the trough. A body of liquid metal is contained in the trough which submerges a portion of the seal blade. The seal blade is provided with at least one aperture located above the body of liquid metal for providing fluid communication between the annulus intermediate the dip seal and the inflatable seals, and a body of cover gas located inside the vessel. There also is provided means for introducing a purge gas into the annulus intermediate the inflatable seals and the seal blade. The purge gas is introduced in an amount sufficient to substantially reduce diffusion of radioactive cover gas or sodium vapor up to the inflatable seals. The purge gas mixes with the cover gas in the reactor vessel where it can be withdrawn from the vessel for treatment and recycle to the vessel.

Effects of postharvest salicylic acid dipping on Alternaria rot and disease resistance of jujube fruit during storage.

PubMed

Cao, Jiankang; Yan, Jiaqi; Zhao, Yumei; Jiang, Weibo

2013-10-01

Considerable postharvest losses caused by Alternaria alternata often occur in Chinese jujube fruit, and synthetic fungicides have been widely used to protect the fruit from Alternaria rot. However, the potential harmfulness of fungicide residues to human health and the environment cannot be ignored. This study was conducted to develop an alternative approach for controlling postharvest disease by inducing fruit resistance with salicylic acid (SA) dipping. Disease incidence and lesion area in the jujube fruit inoculated with A. alternata were significantly inhibited by 2 and 2.5 mmol L(-1) SA dipping. Naturally infected decay rate and index in jujubes were also significantly reduced by SA dipping during long-term storage at 0°C. SA enhanced activities of the main defense-related enzymes including phenylalanine ammonia-lyase, peroxidase, chitinase and β-1,3-glucanase in the fruit during storage. SA strongly decreased catalase activity but increased superoxide dismutase activity and ascorbic acid content in jujubes. The beneficial effects of SA on fruit protection may be due to its ability to activate several highly coordinated defence-related systems in jujubes, instead of its fungicidal activity. The findings indicated that application of SA would offer an alternative approach that helps to control postharvest disease and maintain storage quality in fruits. © 2013 Society of Chemical Industry.

Ball-and-socket tectonic rotation during the 2013 Mw 7.7 Balochistan earthquake

NASA Astrophysics Data System (ADS)

Barnhart, W. D.; Hayes, G. P.; Briggs, R. W.; Gold, R. D.; Bilham, R.

2014-10-01

The September 2013 Mw 7.7 Balochistan earthquake ruptured a ∼200-km-long segment of the curved Hoshab fault in southern Pakistan with 10 ± 0.2 m of peak sinistral and ∼ 1.7 ± 0.8 m of dip slip. This rupture is unusual because the fault dips 60 ± 15° towards the focus of a small circle centered in northwest Pakistan, and, despite a 30° increase in obliquity along strike, the ratios of strike and dip slip remain relatively uniform. Surface displacements and geodetic and teleseismic source inversions quantify a bilateral rupture that propagated rapidly at shallow depths from a transtensional jog near the northern end of the rupture. Static friction prior to rupture was unusually weak (μ < 0.05), and friction may have approached zero during dynamic rupture. Here we show that the inward-dipping Hoshab fault defines the northern rim of a structural unit in southeast Makran that rotates - akin to a 2-D ball-and-socket joint - counter-clockwise in response to India's penetration into the Eurasian plate. This rotation accounts for complexity in the Chaman fault system and, in principle, reduces seismic potential near Karachi; nonetheless, these findings highlight deficiencies in strong ground motion equations and tectonic models that invoke Anderson-Byerlee faulting predictions.

Ball-and-socket tectonic rotation during the 2013 Mw7.7 Balochistan earthquake

USGS Publications Warehouse

Barnhart, William D.; Hayes, Gavin P.; Briggs, Richard W.; Gold, Ryan D.; Bilham, R.

2014-01-01

The September 2013 Mw7.7 Balochistan earthquake ruptured a ∼200-km-long segment of the curved Hoshab fault in southern Pakistan with 10±0.2 m of peak sinistral and ∼1.7±0.8 m of dip slip. This rupture is unusual because the fault dips 60±15° towards the focus of a small circle centered in northwest Pakistan, and, despite a 30° increase in obliquity along strike, the ratios of strike and dip slip remain relatively uniform. Surface displacements and geodetic and teleseismic source inversions quantify a bilateral rupture that propagated rapidly at shallow depths from a transtensional jog near the northern end of the rupture. Static friction prior to rupture was unusually weak (μ<0.05), and friction may have approached zero during dynamic rupture. Here we show that the inward-dipping Hoshab fault defines the northern rim of a structural unit in southeast Makran that rotates – akin to a 2-D ball-and-socket joint – counter-clockwise in response to India's penetration into the Eurasian plate. This rotation accounts for complexity in the Chaman fault system and, in principle, reduces seismic potential near Karachi; nonetheless, these findings highlight deficiencies in strong ground motion equations and tectonic models that invoke Anderson–Byerlee faulting predictions.

Prevalence of bimaxillary protrusion in a Nigerian population.

PubMed

Isiekwe, M

1990-01-01

Literally, bimaxillary protrusion means the protrusion of the two maxillae. This concept masks the real orthodontic problem of dual incisor proclination (DIP). In an attempt to clarify the identification of DIP a study has been made of biological norms for incisor proclination. In the Nigerian population, DIP is defined as occurring when the intercisal angle is of or less than 108 degrees. On this basis the prevalence of DIP was recorded as 20 per cent. Approximatively three-quarters of persons with DIP had a skeletal 1 antero-posterior jaw relationship.

Molecular detection with terahertz waves based on absorption-induced transparency metamaterials

NASA Astrophysics Data System (ADS)

G. Rodrigo, Sergio; Martín-Moreno, L.

2016-10-01

A system for the detection of spectral signatures of chemical compounds at the Terahertz regime is presented. The system consists on a holey metal film whereby the presence of a given substance provokes the appearance of spectral features in transmission and reflection induced by the molecular specimen. These induced effects can be regarded as an extraordinary optical transmission phenomenon called absorption-induced transparency (AIT). The phenomenon consist precisely in the appearance of peaks in transmission and dips in reflection after sputtering of a chemical compound onto an initially opaque holey metal film. The spectral signatures due to AIT occur unexpectedly close to the absorption energies of the molecules. The presence of a target, a chemical compound, would be thus revealed as a strong drop in reflectivity measurements. We theoretically predict the AIT based system would serve to detect amounts of hydrocyanic acid (HCN) at low rate concentrations.

Functional requirements for an intelligent RPC. [remote power controller for spaceborne electrical distribution system

NASA Technical Reports Server (NTRS)

Aucoin, B. M.; Heller, R. P.

1990-01-01

An intelligent remote power controller (RPC) based on microcomputer technology can implement advanced functions for the accurate and secure detection of all types of faults on a spaceborne electrical distribution system. The intelligent RPC will implement conventional protection functions such as overcurrent, under-voltage, and ground fault protection. Advanced functions for the detection of soft faults, which cannot presently be detected, can also be implemented. Adaptive overcurrent protection changes overcurrent settings based on connected load. Incipient and high-impedance fault detection provides early detection of arcing conditions to prevent fires, and to clear and reconfigure circuits before soft faults progress to a hard-fault condition. Power electronics techniques can be used to implement fault current limiting to prevent voltage dips during hard faults. It is concluded that these techniques will enhance the overall safety and reliability of the distribution system.

Effectiveness of Dexamethasone Iontophoresis for Temporomandibular Joint Involvement in Juvenile Idiopathic Arthritis

PubMed Central

Mina, Rina; Melson, Paula; Powell, Stephanie; Rao, Marepalli; Hinze, Claas; Passo, Murray; Graham, T. Brent; Brunner, Hermine I.

2011-01-01

Objective Temporomandibular joint (TMJ) involvement is common in Juvenile Idiopathic Arthritis (JIA). Dexamethasone iontophoresis (DIP) uses low-grade electric currents for transdermal dexamethasone delivery into deeper anatomic structures. The purpose of this study was to assess the safety and effectiveness of DIP for the treatment of TMJ involvement in JIA, and to delineate variables that are associated with improvement after DIP. Methods Medical records of all JIA patients who underwent DIP for TMJ involvement at a larger tertiary pediatric rheumatology center from 1997 to 2011 were reviewed. DIP was performed using a standard protocol. The effectiveness of DIP was assessed by comparing the maximal inter-incisor opening (MIOTMJ) and the maximal lateral excursion (MLETMJ) before and after treatment. Results Twenty-eight patients (ages 2– 21 years) who received an average of eight DIP treatment sessions per involved TMJ were included in the analysis. Statistically significant improvement in the median MIOTMJ (p< 0.0001) was observed in 68%. The median MLETMJ (p= 0.03) improved in 69%, and resolution of TMJ pain occurred in 73% of the patients who had TMJ pain at baseline. Side effects of DIP were transient site erythema (86%), skin blister (4%), and metallic taste (4%). Improvement in TMJ range of motion from DIP is associated with lower MIOTMJ, lower MLETMJ, and absence of TMJ crepitus at baseline. Conclusion In this pilot study DIP appeared to be an effective and safe initial treatment of TMJ involvement in JIA, especially among patients with decreased TMJ measurements. Prospective controlled studies are needed. PMID:22034112

A seismic coherency method using spectral amplitudes

NASA Astrophysics Data System (ADS)

Sui, Jing-Kun; Zheng, Xiao-Dong; Li, Yan-Dong

2015-09-01

Seismic coherence is used to detect discontinuities in underground media. However, strata with steeply dipping structures often produce false low coherence estimates and thus incorrect discontinuity characterization results. It is important to eliminate or reduce the effect of dipping on coherence estimates. To solve this problem, time-domain dip scanning is typically used to improve estimation of coherence in areas with steeply dipping structures. However, the accuracy of the time-domain estimation of dip is limited by the sampling interval. In contrast, the spectrum amplitude is not affected by the time delays in adjacent seismic traces caused by dipping structures. We propose a coherency algorithm that uses the spectral amplitudes of seismic traces within a predefined analysis window to construct the covariance matrix. The coherency estimates with the proposed algorithm is defined as the ratio between the dominant eigenvalue and the sum of all eigenvalues of the constructed covariance matrix. Thus, we eliminate the effect of dipping structures on coherency estimates. In addition, because different frequency bands of spectral amplitudes are used to estimate coherency, the proposed algorithm has multiscale features. Low frequencies are effective for characterizing large-scale faults, whereas high frequencies are better in characterizing small-scale faults. Application to synthetic and real seismic data show that the proposed algorithm can eliminate the effect of dip and produce better coherence estimates than conventional coherency algorithms in areas with steeply dipping structures.

Heavier Group 13 Metal(I) Heterocycles Stabilized by Sterically Demanding Diiminophosphinates: A Structurally Characterized Monomer-Dimer Pair For Gallium.

PubMed

Hawley, Andrew L; Ohlin, C André; Fohlmeister, Lea; Stasch, Andreas

2017-01-05

We have synthesized and characterized the monomeric diiminophosphinate-stabilized Group 13 metal(I) complexes [ Dip LE:], Dip L=Ph 2 P(NDip) 2 , Dip=2,6-iPr 2 C 6 H 3 ; E=Ga (1), In (2) and Tl (3). In addition, we structurally characterized the dimeric complex [( Dip LGa) 2 ], 1 2 . Similar synthetic attempts using Mes L=Ph 2 P(NMes) 2 , Mes=2,4,6-Me 3 C 6 H 2 afforded product mixtures from which the mixed oxidation state species [( Mes L) 3 Ga 4 I 3 ] 4 was isolated. [ Dip LGa:] 1 is converted with dry air to the gallium(III) oxide species [( Dip LGaO) 2 ] 5. Density Functional Theory studies on [ Dip LE:] and [( Dip LE) 2 ], E=Al-Tl, shed light on the bonding in these compounds and show that the newly formed E-E bonding interactions can be described as weak single σ-bond with no significant π-bonding contribution for E=Al, Ga. A large contribution to the dimer binding enthalpies results from London dispersion forces. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bioavailability and ecotoxicity of arsenic species in solution culture and soil system: implications to remediation.

PubMed

Bolan, Nanthi; Mahimairaja, Santiago; Kunhikrishnan, Anitha; Seshadri, Balaji; Thangarajan, Ramya

2015-06-01

In this work, bioavailability and ecotoxicity of arsenite (As(III)) and arsenate (As(V)) species were compared between solution culture and soil system. Firstly, the adsorption of As(III) and As(V) was compared using a number of non-allophanic and allophanic soils. Secondly, the bioavailability and ecotoxicity were examined using germination, phytoavailability, earthworm, and soil microbial activity tests. Both As-spiked soils and As-contaminated sheep dip soils were used to test bioavailability and ecotoxicity. The sheep dip soil which contained predominantly As(V) species was subject to flooding to reduce As(V) to As(III) and then used along with the control treatment soil to compare the bioavailability between As species. Adsorption of As(V) was much higher than that of As(III), and the difference in adsorption between these two species was more pronounced in the allophanic than non-allophanic soils. In the solution culture, there was no significant difference in bioavailability and ecotoxicity, as measured by germination and phytoavailability tests, between these two As species. Whereas in the As-spiked soils, the bioavailability and ecotoxicity were higher for As(III) than As(V), and the difference was more pronounced in the allophanic than non-allophanic soils. Bioavailability of As increased with the flooding of the sheep dip soils which may be attributed to the reduction of As(V) to As(III) species. The results in this study have demonstrated that while in solution, the bioavailability and ecotoxicity do not vary between As(III) and As(V), in soils, the latter species is less bioavailable than the former species because As(V) is more strongly retained than As(III). Since the bioavailability and ecotoxicity of As depend on the nature of As species present in the environment, risk-based remediation approach should aim at controlling the dynamics of As transformation.

Simultaneous measurement of refractive index and temperature based on all-dielectric metasurface.

PubMed

Hu, Jie; Lang, Tingting; Shi, Guo-Hua

2017-06-26

In this paper, a novel kind of sensors for simultaneous measurement of refractive index and temperature based on all-dielectric metasurfaces is proposed. The metasurfaces are constructed by an array of silicon nanoblocks on top of the bulk fused silica substrate. We used three-dimensional full wave electromagnetic field simulation by finite integral method to accurately calculate the transmission spectrum of the metasurfaces. Two transmission dips corresponding to the electric and magnetic resonances are observed. Both dips shift as the ambient refractive index or the temperature changes. Simulation results show that the sensing sensitivities of two dips to the refractive index are 243.44 nm/RIU and 159.43 nm/RIU, respectively, while the sensitivities to the temperature are 50.47 pm/°C and 75.20 pm/°C, respectively. After introducing four holes into each silicon nanoblock, the electromagnetic field overlap in the surrounding medium can be further promoted, and the sensitivities to the refractive index increase to 306.71 nm/RIU and 204.27 nm/RIU, respectively. Our proposed sensors have advantages of polarization insensitive, small size, and low loss, which offer them high potential applications in physical, biological and chemical sensing fields.

A fiber-optic interferometer based on non-adiabatic fiber taper and long-period fiber grating for simultaneous measurement of magnetic field and temperature

NASA Astrophysics Data System (ADS)

Kang, Shouxin; Zhang, Hao; Liu, Bo; Lin, Wei; Zhang, Ning; Miao, Yinping

2016-01-01

A dual-parameter sensor based on a fiber-optic interferometer consisting of a non-adiabatic fiber taper and a long-period fiber grating (LPFG) integrated with magnetic nanoparticle fluids has been proposed and experimentally demonstrated. Due to the Mach-Zehnder interference induced by the concatenation of the fiber taper and long-period grating, an interferometric spectrum could be acquired within the transmission resonance spectral envelope of the LPFG. Thanks to different magnetic field and temperature sensitivities of difference interference dips, simultaneous measurement of the magnetic field intensity and environmental temperature could be achieved. Moreover, due to the variation in coupling coefficients of the fiber taper and the LPFG in response to the change of the applied magnetic field intensity, some of the interference dips would exhibit opposite magnetic-field-intensity-dependent transmission loss variation behavior. Magnetic field intensity and temperature sensitivities of 0.017 31 dB Oe-1 and 0.0315 dB K-1, and -0.024 55 dB Oe-1 and -0.056 28 dB K-1 were experimentally acquired for the experimentally monitored interference dips.

Attenuation of pressure dips underneath piles of spherocylinders.

PubMed

Zhao, Haiyang; An, Xizhong; Gou, Dazhao; Zhao, Bo; Yang, Runyu

2018-05-30

The discrete element method (DEM) was used to simulate the piling of rod-like (elongated sphero-cylindrical) particles, mainly focusing on the effect of particle shape on the structural and force properties of the piles. In this work, rod-like particles of different aspect ratios were discharged on a flat surface to form wedge-shaped piles. The surface properties of the piles were characterized in terms of angle of repose and stress at the bottom of the piles. The results showed that the rise of the angle of repose became slower with the increase of particle aspect ratio. The pressure dip underneath the piles reached the maximum when the particle aspect ratio was around 1.6, beyond which the pressure dip phenomenon became attenuated. Both the pressure dip and the shear stress dip were quantitatively examined. The structure and forces inside the piles were further analyzed to understand the change in pressure dip, indicating that "bridging" or "arching" structures within the piles were the cause of the pressure dip.

Socioeconomic Status, Nocturnal Blood Pressure Dipping, and Psychosocial Factors: A Cross-Sectional Investigation in Mexican-American Women

PubMed Central

Gallo, Linda C.; Roesch, Scott C.; Mills, Paul J.; Barrett-Connor, Elizabeth; Talavera, Greg A.; Elder, John P.; Matthews, Karen A.

2013-01-01

Background Despite established links between reduced nocturnal blood pressure (BP) dipping and cardiovascular disease, BP dipping research in Hispanics is limited. Purpose This study investigated socioeconomic status (SES) as a predictor of BP dipping and the contributions of psychosocial factors to this relationship. Analyses were conducted for the overall sample and separately for higher and lower acculturated women. Methods Mexican-American women (N=291; 40–65 years) reported demographics and completed psychosocial assessments and 36-h ambulatory BP monitoring. Results Lower SES related to reduced BP dipping in the overall sample and in more US-acculturated women (r’s=.17–.30, p’s<.05), but not in less-acculturated women (r’s=.07, p’s>.10). An indirect effect model from SES to BP dipping via psychosocial resources/risk fits well across samples. Conclusions In Mexican-American women, the nature of SES gradients in BP dipping and the roles of psychosocial resources/risk differ by acculturation level. PMID:22777880

Investigation on the Cracking Character of Jointed Rock Mass Beneath TBM Disc Cutter

NASA Astrophysics Data System (ADS)

Yang, Haiqing; Liu, Junfeng; Liu, Bolong

2018-04-01

With the purpose to investigate the influence of joint dip angle and spacing on the TBM rock-breaking efficacy and cracking behaviour, experiments that include miniature cutter head tests are carried out on sandstone rock material. In the experiment, prefabricated joints of different forms are made in rock samples. Then theoretical analysis is conducted to improve the calculating models of the fractured work and crack length of rock in the TBM process. The experimental results indicate that lower rupture angles appear for specimens with joint dip angles between 45° and 60°. Meanwhile, rock-breaking efficacy for rock mass with joint dip angles in this interval is also higher. Besides, the fracture patterns are transformed from compressive shear mode to tensile shear mode as the joint spacing decreases. As a result, failure in a greater extent is resulted for specimens with smaller joint spacings. The results above suggest that joint dip angle between 45° and 60° and joint spacing of 1 cm are the optimal rock-breaking conditions for the tested specimens. Combining the present experimental data and taking the joint dip angle and spacing into consideration, the calculating model for rock fractured work that proposed by previous scholars is improved. Finally, theoretical solution of rock median and side crack length is also derived based on the analytical method of elastoplastic invasion fracture for indenter. The result of the analytical solution is also in good agreement with the actual measured experimental result. The present study may provide some primary knowledge about the rock cracking character and breaking efficacy under different engineering conditions.

Multistory duplexes with forward dipping roofs, north central Brooks Range, Alaska

USGS Publications Warehouse

Wallace, W.K.; Moore, Thomas E.; Plafker, G.

1997-01-01

The Endicott Mountains allochthon has been thrust far northward over the North Slope parautochthon in the northern Brooks Range. Progressively younger units are exposed northward within the allochthon. To the south, the incompetent Hunt Fork Shale has thickened internally by asymmetric folds and thrust faults. Northward, the competent Kanayut Conglomerate forms a duplex between a floor thrust in Hunt Fork and a roof thrust in the Kayak Shale. To the north, the competent Lisburne Group forms a duplex between a floor thrust in Kayak and a roof thrust in the Siksikpuk Formation. Both duplexes formed from north vergent detachment folds whose steep limbs were later truncated by south dipping thrust faults that only locally breach immediately overlying roof thrusts. Within the parautochthon, the Kayak, Lisburne, and Siksikpuk-equivalent Echooka Formation form a duplex identical to that in the allochthon. This duplex is succeeded abruptly northward by detachment folds in Lisburne. These folds are parasitic to an anticlinorium interpreted to reflect a fault-bend folded horse in North Slope "basement," with a roof thrust in Kayak and a floor thrust at depth. These structures constitute two northward tapered, internally deformed wedges that are juxtaposed at the base of the allochthon. Within each wedge, competent units have been shortened independently between detachments, located mainly in incompetent units. The basal detachment of each wedge cuts upsection forward (northward) to define a wedge geometry within which units dip regionally forward. These dips reflect forward decrease in internal structural thickening by forward vergent folds and hindward dipping thrust faults. Copyright 1997 by the American Geophysical Union.

T-DNA transfer and T-DNA integration efficiencies upon Arabidopsis thaliana root explant cocultivation and floral dip transformation.

PubMed

Ghedira, Rim; De Buck, Sylvie; Van Ex, Frédéric; Angenon, Geert; Depicker, Ann

2013-12-01

T-DNA transfer and integration frequencies during Agrobacterium-mediated root explant cocultivation and floral dip transformations of Arabidopsis thaliana were analyzed with and without selection for transformation-competent cells. Based on the presence or absence of CRE recombinase activity without or with the CRE T-DNA being integrated, transient expression versus stable transformation was differentiated. During root explant cocultivation, continuous light enhanced the number of plant cells competent for interaction with Agrobacterium and thus the number of transient gene expression events. However, in transformation competent plant cells, continuous light did not further enhance cotransfer or cointegration frequencies. Upon selection for root transformants expressing a first T-DNA, 43-69 % of these transformants showed cotransfer of another non-selected T-DNA in two different light regimes. However, integration of the non-selected cotransferred T-DNA occurred only in 19-46 % of these transformants, indicating that T-DNA integration in regenerating root cells limits the transformation frequencies. After floral dip transformation, transient T-DNA expression without integration could not be detected, while stable T-DNA transformation occurred in 0.5-1.3 % of the T1 seedlings. Upon selection for floral dip transformants with a first T-DNA, 8-34 % of the transformants showed cotransfer of the other non-selected T-DNA and in 93-100 % of them, the T-DNA was also integrated. Therefore, a productive interaction between the agrobacteria and the female gametophyte, rather than the T-DNA integration process, restricts the floral dip transformation frequencies.

Laryngeal dynamics of pedagogical taan gestures in Indian classical singing.

PubMed

Radhakrishnan, Nandhakumar; Scherer, Ronald C; Bandyopadhyay, Santanu

2011-05-01

Vocal modulations characterize many styles of singing. Vibrato, trill, and trillo are some of the ornaments that Western classical singers use. Likewise, taan is one of the basic frequency modulations demonstrated by Hindustani Indian classical singers. The objective of this descriptive study was to discover the F₀ contour of taan; establish selected acoustic, aerodynamic, and glottographic characteristics of the taan gesture; and explore the pedagogical taan utterances demonstrated by a well-known singer and teacher. Exploratory. Fundamental frequency, alternating current (AC) glottal flow, and electroglottographic width measures were obtained for taan productions by the classical Indian singer and teacher who demonstrated taan rate variations based on his pedagogical approach. The structure of the taan gesture was found to be an F₀ lowering and rising (the "taan dip") followed by a relatively flat portion (the "taan superior surface"). Rate of the F₀ structure of the taan gestures ranged from approximately 1.65 to 3.41Hz, and the F₀ extent ranged from 1.87 to 2.21semitone (ST). As the rate of the taan gesture increased, the superior surface shortened, whereas the taan dip stayed relatively constant (ranging from 170 to 230 ms). AC flow was greater for the lowest frequencies of the dip and faster rates. The pedagogical taan gesture has a specific structure of an F₀ dip followed by a relatively flat F₀ portion that shortens as taan rate increases. The F₀ dip and extent are relatively robust across rate. The taan productions are voluntarily controlled, in contrast to vibrato productions. Copyright © 2011 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Permethrin-Treated Clothing as Protection against the Dengue Vector, Aedes aegypti: Extent and Duration of Protection

PubMed Central

DeRaedt Banks, Sarah; Orsborne, James; Gezan, Salvador A.; Kaur, Harparkash; Wilder-Smith, Annelies; Lindsey, Steve W.; Logan, James G.

2015-01-01

Introduction Dengue transmission by the mosquito vector, Aedes aegypti, occurs indoors and outdoors during the day. Personal protection of individuals, particularly when outside, is challenging. Here we assess the efficacy and durability of different types of insecticide-treated clothing on laboratory-reared Ae. aegypti. Methods Standardised World Health Organisation Pesticide Evaluation Scheme (WHOPES) cone tests and arm-in-cage assays were used to assess knockdown (KD) and mortality of Ae. aegypti tested against factory-treated fabric, home-dipped fabric and microencapsulated fabric. Based on the testing of these three different treatment types, the most protective was selected for further analysis using arm-in cage assays with the effect of washing, ultra-violet light, and ironing investigated using high pressure liquid chromatography. Results Efficacy varied between the microencapsulated and factory dipped fabrics in cone testing. Factory-dipped clothing showed the greatest effect on KD (3 min 38.1%; 1 hour 96.5%) and mortality (97.1%) with no significant difference between this and the factory dipped school uniforms. Factory-dipped clothing was therefore selected for further testing. Factory dipped clothing provided 59% (95% CI = 49.2%– 66.9%) reduction in landing and a 100% reduction in biting in arm-in-cage tests. Washing duration and technique had a significant effect, with insecticidal longevity shown to be greater with machine washing (LW50 = 33.4) compared to simulated hand washing (LW50 = 17.6). Ironing significantly reduced permethrin content after 1 week of simulated use, with a 96.7% decrease after 3 months although UV exposure did not reduce permethrin content within clothing significantly after 3 months simulated use. Conclusion Permethrin-treated clothing may be a promising intervention in reducing dengue transmission. However, our findings also suggest that clothing may provide only short-term protection due to the effect of washing and ironing, highlighting the need for improved fabric treatment techniques. PMID:26440967

Permethrin-Treated Clothing as Protection against the Dengue Vector, Aedes aegypti: Extent and Duration of Protection.

PubMed

DeRaedt Banks, Sarah; Orsborne, James; Gezan, Salvador A; Kaur, Harparkash; Wilder-Smith, Annelies; Lindsey, Steve W; Logan, James G

2015-01-01

Dengue transmission by the mosquito vector, Aedes aegypti, occurs indoors and outdoors during the day. Personal protection of individuals, particularly when outside, is challenging. Here we assess the efficacy and durability of different types of insecticide-treated clothing on laboratory-reared Ae. aegypti. Standardised World Health Organisation Pesticide Evaluation Scheme (WHOPES) cone tests and arm-in-cage assays were used to assess knockdown (KD) and mortality of Ae. aegypti tested against factory-treated fabric, home-dipped fabric and microencapsulated fabric. Based on the testing of these three different treatment types, the most protective was selected for further analysis using arm-in cage assays with the effect of washing, ultra-violet light, and ironing investigated using high pressure liquid chromatography. Efficacy varied between the microencapsulated and factory dipped fabrics in cone testing. Factory-dipped clothing showed the greatest effect on KD (3 min 38.1%; 1 hour 96.5%) and mortality (97.1%) with no significant difference between this and the factory dipped school uniforms. Factory-dipped clothing was therefore selected for further testing. Factory dipped clothing provided 59% (95% CI = 49.2%- 66.9%) reduction in landing and a 100% reduction in biting in arm-in-cage tests. Washing duration and technique had a significant effect, with insecticidal longevity shown to be greater with machine washing (LW50 = 33.4) compared to simulated hand washing (LW50 = 17.6). Ironing significantly reduced permethrin content after 1 week of simulated use, with a 96.7% decrease after 3 months although UV exposure did not reduce permethrin content within clothing significantly after 3 months simulated use. Permethrin-treated clothing may be a promising intervention in reducing dengue transmission. However, our findings also suggest that clothing may provide only short-term protection due to the effect of washing and ironing, highlighting the need for improved fabric treatment techniques.

Measurement of Local Partial Pressure of Oxygen in the Brain Tissue under Normoxia and Epilepsy with Phosphorescence Lifetime Microscopy.

PubMed

Zhang, Cong; Bélanger, Samuel; Pouliot, Philippe; Lesage, Frédéric

2015-01-01

In this work a method for measuring brain oxygen partial pressure with confocal phosphorescence lifetime microscopy system is reported. When used in conjunction with a dendritic phosphorescent probe, Oxyphor G4, this system enabled minimally invasive measurements of oxygen partial pressure (pO2) in cerebral tissue with high spatial and temporal resolution during 4-AP induced epileptic seizures. Investigating epileptic events, we characterized the spatio-temporal distribution of the "initial dip" in pO2 near the probe injection site and along nearby arterioles. Our results reveal a correlation between the percent change in the pO2 signal during the "initial dip" and the duration of seizure-like activity, which can help localize the epileptic focus and predict the length of seizure.

Ginga observations of the dipping low-mass X-ray binaries XB 1916-053 and EXO 1748-676

NASA Technical Reports Server (NTRS)

Smale, Alan P.; Mukai, Koji; Williams, O. R.; Jones, Mark H.; Corbet, Robin H. D.

1992-01-01

Ginga observations of XB 1916-053 and EXO 0748-676, low-mass X-ray binaries with pronounced dips of variable depth and duration in their X-ray light curves, are reported. Periodicity studies of XB-1916-053 show results consistent with those from previous Ginga observations, specifically, that the derived X-ray period is shorter than the optical period by about 1 percent. This problem is discussed, and a more refined model for the system is described. Three bursts were detected during the observation of XB 1916-053, the second of which occurred during a dip. Spectral analysis suggests that the second burst caused an almost instantaneous ionization of the absorbing medium in the line of sight. This material then returned to its equilibrium state on the same time scale as the burst decay. Loose limits are placed upon the possible clumpiness of the material responsible for the accretion disk structure in XB 1916-053 and EXO 0748-676.

Linking Precursor Alterations to Nanoscale Structure and Optical Transparency in Polymer Assisted Fast-Rate Dip-Coating of Vanadium Oxide Thin Films

PubMed Central

Glynn, Colm; Creedon, Donal; Geaney, Hugh; Armstrong, Eileen; Collins, Timothy; Morris, Michael A.; Dwyer, Colm O’

2015-01-01

Solution processed metal oxide thin films are important for modern optoelectronic devices ranging from thin film transistors to photovoltaics and for functional optical coatings. Solution processed techniques such as dip-coating, allow thin films to be rapidly deposited over a large range of surfaces including curved, flexible or plastic substrates without extensive processing of comparative vapour or physical deposition methods. To increase the effectiveness and versatility of dip-coated thin films, alterations to commonly used precursors can be made that facilitate controlled thin film deposition. The effects of polymer assisted deposition and changes in solvent-alkoxide dilution on the morphology, structure, optoelectronic properties and crystallinity of vanadium pentoxide thin films was studied using a dip-coating method using a substrate withdrawal speed within the fast-rate draining regime. The formation of sub-100 nm thin films could be achieved rapidly from dilute alkoxide based precursor solutions with high optical transmission in the visible, linked to the phase and film structure. The effects of the polymer addition was shown to change the crystallized vanadium pentoxide thin films from a granular surface structure to a polycrystalline structure composed of a high density of smaller in-plane grains, resulting in a uniform surface morphology with lower thickness and roughness. PMID:26123117

Development of combination tapered fiber-optic biosensor dip probe for quantitative estimation of interleukin-6 in serum samples

NASA Astrophysics Data System (ADS)

Wang, Chun Wei; Manne, Upender; Reddy, Vishnu B.; Oelschlager, Denise K.; Katkoori, Venkat R.; Grizzle, William E.; Kapoor, Rakesh

2010-11-01

A combination tapered fiber-optic biosensor (CTFOB) dip probe for rapid and cost-effective quantification of proteins in serum samples has been developed. This device relies on diode laser excitation and a charged-coupled device spectrometer and functions on a technique of sandwich immunoassay. As a proof of principle, this technique was applied in a quantitative estimation of interleukin IL-6. The probes detected IL-6 at picomolar levels in serum samples obtained from a patient with lupus, an autoimmune disease, and a patient with lymphoma. The estimated concentration of IL-6 in the lupus sample was 5.9 +/- 0.6 pM, and in the lymphoma sample, it was below the detection limit. These concentrations were verified by a procedure involving bead-based xMAP technology. A similar trend in the concentrations was observed. The specificity of the CTFOB dip probes was assessed by analysis with receiver operating characteristics. This analysis suggests that the dip probes can detect 5-pM or higher concentration of IL-6 in these samples with specificities of 100%. The results provide information for guiding further studies in the utilization of these probes to quantify other analytes in body fluids with high specificity and sensitivity.

Thermochronologic constraints on the Miocene slip history of the South Tibetan detachment system in the Everest region, central Himalaya

NASA Astrophysics Data System (ADS)

Schultz, M.; Hodges, K. V.; Van Soest, M. C.; Wartho, J. A.

2014-12-01

North-dipping, low-angle normal faults of the South Tibetan detachment system (STDS) can be traced for a distance of more than 2000 km along strike and represent an important tectonic characteristic of the Miocene Himalayan-Tibetan orogenic system. Nowhere is the STDS better exposed than the N-S-trending Rongbuk Valley in southern Tibet, where it can be traced down dip from the summit of Everest for a distance of over 30 km before disappearing beneath the valley floor. This places a minimum constraint on Miocene displacement on the feature in this area, but some research groups have suggested ~200 km of displacement based on the difference in metamorphic pressures across the STDS and the very low (< 15˚) primary dip of the structure. We are exploring this issue further using developing (U-Th)/He and 40Ar/39Ar datasets from deformed footwall sillimanite gneisses and leucogranites. Data obtained thus far indicate relatively rapid cooling of the footwall after the intrusion of deformed leucogranites at ca. 16.7 Ma to muscovite 40Ar/39Ar closure temperatures (ca. 15.5-14.2 Ma) and zircon (U-Th)/He closure temperatures (ca. 14.5-11 Ma). We attribute this cooling to tectonic denudation related to ca. 16 Ma STDS slip. Although the (U-Th)/He systematics of apatites from these rocks is complex, our current interpretation of available data places cooling through the ca. 75˚C closure isotherm at ca. 8-9 Ma, which would suggest a significant reduction in cooling rate that is observed in our inverse model runs of the 1D program, HeFTy. Ongoing analyses of footwall samples from ~8 km to the north of our Rongbuk sample localities in the Ra Chu river valley will greatly strengthen our datasets. With the Ra Chu analyses, our datasets will constrain the cooling history of the footwall for more than 20 km perpendicular to the strike of the detachment. Our presentation will also incorporate results from the program Pecube that will contribute to our calculation of the slip rate by specifying the appropriate exhumation rate.

[Multi-centre clinical assessment of the Russian language version of the Diagnostic Interview for Psychoses].

PubMed

Smirnova, D A; Petrova, N N; Pavlichenko, A V; Martynikhin, I A; Dorofeikova, M V; Eremkin, V I; Izmailova, O V; Osadshiy, Yu Yu; Romanov, D V; Ubeikon, D A; Fedotov, I A; Sheifer, M S; Shustov, A D; Yashikhina, A A; Clark, M; Badcock, J; Watterreus, A; Morgan, V; Jablensky, A

2018-01-01

The Diagnostic Interview for Psychoses (DIP) was developed to enhance the quality of diagnostic assessment of psychotic disorders. The aim of the study was the adaptation of the Russian language version and evaluation of its validity and reliability. Ninety-eight patients with psychotic disorders (89 video recordings) were assessed by 12 interviewers using the Russian version of DIP at 7 clinical sites (in 6 cities of the Russian Federation). DIP ratings on 32 cases of a randomized case sample were made by 9 interviewers and the inter-rater reliability was compared with the researchers' DIP ratings. Overall pairwise agreement and Cohen's kappa were calculated. Diagnostic validity was evaluated on the basis of comparing the researchers' ratings using the Russian version of DIP with the 'gold standard' ratings of the same 62 clinical cases from the Western Australia Family Study Schizophrenia (WAFSS). The mean duration of the interview was 47±21 minutes. The Kappa statistic demonstrated a significant or almost perfect level of agreement on the majority of DIP items (84.54%) and a significant agreement for the ICD-10 diagnoses generated by the DIP computer diagnostic algorithm (κ=0.68; 95% CI 0.53,0.93). The level of agreement on the researchers' diagnoses was considerably lower (κ=0.31; 95% CI 0.06,0.56). The agreement on affective and positive psychotic symptoms was significantly higher than agreement on negative symptoms (F(2,44)=20.72, p<0.001, η2=0.485). The diagnostic validity of the Russian language version of DIP was confirmed by 73% (45/62) of the Russian DIP diagnoses matching the original WAFSS diagnoses. Among the mismatched diagnoses were 80 cases with a diagnosis of F20 Schizophrenia in the medical documentation compared to the researchers' F20 diagnoses in only 68 patients and in 62 of the DIP computerized diagnostic outputs. The reported level of subjective difficulties experienced when using the DIP was low to moderate. The results of the study confirm the validity and reliability of the Russian version of the DIP for evaluating psychotic disorders. DIP can be recommended for use in education and training, clinical practice and research as an important diagnostic resource.

Web platform using digital image processing and geographic information system tools: a Brazilian case study on dengue.

PubMed

Brasil, Lourdes M; Gomes, Marília M F; Miosso, Cristiano J; da Silva, Marlete M; Amvame-Nze, Georges D

2015-07-16

Dengue fever is endemic in Asia, the Americas, the East of the Mediterranean and the Western Pacific. According to the World Health Organization, it is one of the diseases of greatest impact on health, affecting millions of people each year worldwide. A fast detection of increases in populations of the transmitting vector, the Aedes aegypti mosquito, is essential to avoid dengue outbreaks. Unfortunately, in several countries, such as Brazil, the current methods for detecting populations changes and disseminating this information are too slow to allow efficient allocation of resources to fight outbreaks. To reduce the delay in providing the information regarding A. aegypti population changes, we propose, develop, and evaluate a system for counting the eggs found in special traps and to provide the collected data using a web structure with geographical location resources. One of the most useful tools for the detection and surveillance of arthropods is the ovitrap, a special trap built to collect the mosquito eggs. This allows for an egg counting process, which is still usually performed manually, in countries such as Brazil. We implement and evaluate a novel system for automatically counting the eggs found in the ovitraps' cardboards. The system we propose is based on digital image processing (DIP) techniques, as well as a Web based Semi-Automatic Counting System (SCSA-WEB). All data collected are geographically referenced in a geographic information system (GIS) and made available on a Web platform. The work was developed in Gama's administrative region, in Brasília/Brazil, with the aid of the Environmental Surveillance Directory (DIVAL-Gama) and Brasília's Board of Health (SSDF), in partnership with the University of Brasília (UnB). The system was built based on a field survey carried out during three months and provided by health professionals. These professionals provided 84 cardboards from 84 ovitraps, sized 15 × 5 cm. In developing the system, we conducted the following steps: i. Obtain images from the eggs on an ovitrap's cardboards, with a microscope. ii. Apply a proposed image-processing-based semi-automatic counting system. The system we developed uses the Java programming language and the Java Server Faces technology. This is a framework suite for web applications development. This approach will allow a simple migration to any Operating System platform and future applications on mobile devices. iii. Collect and store all data into a Database (DB) and then georeference them in a GIS. The Database Management System used to develop the DB is based on PostgreSQL. The GIS will assist in the visualization and spatial analysis of digital maps, allowing the location of Dengue outbreaks in the region of study. This will also facilitate the planning, analysis, and evaluation of temporal and spatial epidemiology, as required by the Brazilian Health Care Control Center. iv. Deploy the SCSA-WEB, DB and GIS on a single Web platform. The statistical results obtained by DIP were satisfactory when compared with the SCSA-WEB's semi-automated eggs count. The results also indicate that the time spent in manual counting has being considerably reduced when using our fully automated DIP algorithm and semi-automated SCSA-WEB. The developed georeferencing Web platform proves to be of great support for future visualization with statistical and trace analysis of the disease. The analyses suggest the efficiency of our algorithm for automatic eggs counting, in terms of expediting the work of the laboratory technician, reducing considerably its time and error counting rates. We believe that this kind of integrated platform and tools can simplify the decision making process of the Brazilian Health Care Control Center.

29 CFR 1910.125 - Additional requirements for dipping and coating operations that use flammable or combustible...

Code of Federal Regulations, 2010 CFR

2010-07-01

... overflow piping is at least 3 inches (7.6 cm) in diameter and has sufficient capacity to prevent the dip... liquid to the tank is electrically bonded to the dip tank and positively grounded to prevent static... must prohibit smoking in a vapor area and must post a readily visible “No Smoking” sign near each dip...

Blink rate is associated with drug-induced parkinsonism in patients with severe mental illness, but does not meet requirements to serve as a clinical test: the Curacao extrapyramidal syndromes study XIII.

PubMed

Mentzel, Charlotte L; Bakker, P Roberto; van Os, Jim; Drukker, Marjan; Matroos, Glenn E; Tijssen, Marina A J; van Harten, Peter N

2017-08-25

Drug-induced parkinsonism (DIP) has a high prevalence and is associated with poorer quality of life. To find a practical clinical tool to assess DIP in patients with severe mental illness (SMI), the association between blink rate and drug-induced parkinsonism (DIP) was assessed. In a cohort of 204 SMI patients receiving care from the only mental health service of the previous Dutch Antilles, blink rate per minute during conversation was assessed by an additional trained movement disorder specialist. DIP was rated on the Unified Parkinson's Disease Rating Scale (UPDRS) in 878 assessments over a period of 18 years. Diagnostic values of blink rate were calculated. DIP prevalence was 36%, average blink rate was 14 (standard deviation (SD) 11) for patients with DIP, and 19 (SD 14) for patients without. There was a significant association between blink rate and DIP (p < 0.001). With a blink rate cut-off of 20 blinks per minute, sensitivity was 77% and specificity was 38%. A 10% percentile cut-off model resulted in an area under the ROC curve of 0.61. A logistic prediction model between dichotomous DIP and continuous blink rate per minute an area under the ROC curve of 0.70. There is a significant association between blink rate and DIP as diagnosed on the UPDRS. However, blink rate sensitivity and specificity with regard to DIP are too low to replace clinical rating scales in routine psychiatric practice. The study was started over 20 years ago in 1992, at the time registering a trial was not common practice, therefore the study was never registered.

Thermal buoyancy on Venus - Underthrusting vs subduction

NASA Technical Reports Server (NTRS)

Burt, Jeffrey D.; Head, James W.

1992-01-01

The thermal and buoyancy consequences of the subduction endmember are modeled in an attempt to evaluate the conditions distinguishing underthrusting and subduction. Thermal changes in slabs subducting into the Venusian mantle with a range of initial geotherms are used to predict density changes and, thus, slab buoyancy. Based on a model for subduction-induced mantle flow, it is then argued that the angle of the slab dip helps differentiate between underthrusting and subduction. Mantle flow applies torques to the slab which, in combination with torques due to slab buoyancy, act to change the angle of slab dip.

The Development of Performance-Based Auditory Aviation Classification Standards in the U.S. Navy,

DTIC Science & Technology

1987-12-01

Gerontology, Vol. 24(2), pp. 189-192, 1969. 10. Palva, A. and Jokinen, K., ’The Role of the Binaural Test in Filtered Speech Audiometry." Acta Oto...BEAD BEAT BEAN REEL HEEL EEL PAVE PALE PAY WIG RIG FIG GALE MALE TALE PAGE PANE PACE PIG BIG DIG PALE SALE BALE DID DIN DIP SAP SAG SAD SIN WIN...SEEN SEED SEEK CAME GAME SAME NEAT BEAT SEAT SEEM SEETHE SEEP PAD PASS PATH PARK MARK HARK SIP RIP TIP PACK PAN PAT DARK LARK BARK LIP HIP DIP LED

Redox non-innocent bis(2,6-diimine-pyridine) ligand-iron complexes as anolytes for flow battery applications.

PubMed

Duarte, Gabriel M; Braun, Jason D; Giesbrecht, Patrick K; Herbert, David E

2017-12-21

Diiminepyridines are a well-known class of "non-innocent" ligands that confer additional redox activity to coordination complexes beyond metal-centred oxidation/reduction. Here, we demonstrate that metal coordination complexes (MCCs) of diiminepyridine (DIP) ligands with iron are suitable anolytes for redox-flow battery applications, with enhanced capacitance and stability compared with bipyridine analogs, and access to storage of up to 1.6 electron equivalents. Substitution of the ligand is shown to be a key factor in the cycling stability and performance of MCCs based on DIP ligands, opening the door to further optimization.

Design of a pressurized lunar rover

NASA Technical Reports Server (NTRS)

Bhardwaj, Manoj; Bulsara, Vatsal; Kokan, David; Shariff, Shaun; Svarverud, Eric; Wirz, Richard

1992-01-01

A pressurized lunar rover is necessary for future long-term habitation of the moon. The rover must be able to safely perform many tasks, ranging from transportation and reconnaissance to exploration and rescue missions. Numerous designs were considered in an effort to maintain a low overall mass and good mobility characteristics. The configuration adopted consists of two cylindrical pressure hulls passively connected by a pressurized flexible passageway. The vehicle has an overall length of 11 meters and a total mass of seven metric tons. The rover is driven by eight independently powered two meter diameter wheels. The dual-cylinder concept allows a combination of articulated frame and double Ackermann steering for executing turns. In an emergency, the individual drive motors allow the option of skid steering as well. Two wheels are connected to either side of each cylinder through a pinned bar which allows constant ground contact. Together, these systems allow the rover to easily meet its mobility requirements. A dynamic isotope power system (DIPS), in conjunction with a closed Brayton cycle, supplied the rover with a continuous supply of 8.5 kW. The occupants are all protected from the DIPS system's radiation by a shield of tantalum. The large amount of heat produced by the DIPS and other rover systems is rejected by thermal radiators. The thermal radiators and solar collectors are located on the top of the rear cylinder. The solar collectors are used to recharge batteries for peak power periods. The rover's shell is made of graphite-epoxy coated with multi-layer insulation (MLI). The graphite-epoxy provides strength while the thermally resistant MLI gives protection from the lunar environment. An elastomer separates the two materials to compensate for the thermal mismatch. The communications system allows for communication with the lunar base with an option for direct communication with earth via a lunar satellite link. The various links are combined into one signal broadcast in the S-band at 2.3 GHz. The rover is fitted with a parabolic reflector disk for S-band transmission, and an omnidirectional antenna for local extravehicular activity (EVA) communication. The rover's guidance, navigation, and control subsystem consists of an inertial guidance system, an orbiting lunar satellite, and an obstacle avoidance system. In addition, the rover is equipped with a number of external fixtures including two telerobotic arms, lights, cameras, EVA storage, manlocks, a docking fixture, solar panels, thermal radiators, and a scientific airlock. In conclusion, this rover meets all of the design requirements and clearly surpasses them in the areas of mobility and maneuverability.

Social support and nocturnal blood pressure dipping: a systematic review.

PubMed

Fortmann, Addie L; Gallo, Linda C

2013-03-01

Attenuated nocturnal blood pressure (BP) dipping is a better predictor of cardiovascular disease (CVD) morbidity and mortality than resting BP measurements. Studies have reported associations between social support, variously defined, and BP dipping. A systematic review of the literature was conducted to investigate associations of functional and structural social support with nocturnal BP dipping assessed over a minimum of 24 hours. A total of 297 articles were identified. Of these, 11 met criteria for inclusion; all studies were cross-sectional in design and included adult participants only (mean age = 19 to 72 years). Evidence was most consistent for an association between functional support and BP dipping, such that 5 of 7 studies reported statistically (or marginally) significant positive associations with BP dipping. Statistically significant functional support-BP dipping associations were moderate (standardized effect size (d) = 0.41) to large (d = 2.01) in magnitude. Studies examining structural support were fewer and relatively less consistent; however, preliminary evidence was observed for associations of marital status and social contact frequency with BP dipping. Statistically significant structural support findings were medium (d = 0.53) to large (d = 1.13) in magnitude. Overall, findings suggest a link between higher levels of functional support and greater nocturnal BP dipping; preliminary evidence was also observed for the protective effects of marriage and social contact frequency. Nonetheless, the relatively small number of studies conducted to date and the heterogeneity of findings across meaningful subgroups suggest that additional research is needed to substantiate these conclusions.

Multileaf collimator tongue-and-groove effect on depth and off-axis doses: A comparison of treatment planning data with measurements and Monte Carlo calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Hee Jung; Department of Biomedical Engineering, Seoul National University, Seoul; Department of Radiation Oncology, Soonchunhyang University Hospital, Seoul

2015-01-01

To investigate how accurately treatment planning systems (TPSs) account for the tongue-and-groove (TG) effect, Monte Carlo (MC) simulations and radiochromic film (RCF) measurements were performed for comparison with TPS results. Two commercial TPSs computed the TG effect for Varian Millennium 120 multileaf collimator (MLC). The TG effect on off-axis dose profile at 3 depths of solid water was estimated as the maximum depth and the full width at half maximum (FWHM) of the dose dip at an interleaf position. When compared with the off-axis dose of open field, the maximum depth of the dose dip for MC and RCF rangedmore » from 10.1% to 20.6%; the maximum depth of the dose dip gradually decreased by up to 8.7% with increasing depths of 1.5 to 10 cm and also by up to 4.1% with increasing off-axis distances of 0 to 13 cm. However, TPS results showed at most a 2.7% decrease for the same depth range and a negligible variation for the same off-axis distances. The FWHM of the dose dip was approximately 0.19 cm for MC and 0.17 cm for RCF, but 0.30 cm for Eclipse TPS and 0.45 cm for Pinnacle TPS. Accordingly, the integrated value of TG dose dip for TPS was larger than that for MC and RCF and almost invariant along the depths and off-axis distances. We concluded that the TG dependence on depth and off-axis doses shown in the MC and RCF results could not be appropriately modeled by the TPS versions in this study.« less

Contraintes sismiques sur les structures crustales de l'Abitibi et de l'Opatica

NASA Astrophysics Data System (ADS)

Bellefleur, Gilles

The objectives of the work presented in this thesis are two-fold. The first consists in determining the tri-dimensional orientation of reflective structures from seismic reflection data acquired along 2D crooked profiles, while the second, based on these orientations, consists in defining geometric constraints on the tectonic scenarios proposed for the Abitibi and Opatica subprovinces. To provide precise estimates of reflector orientations, we use three distinct approaches, which, however, require acquisition profiles that call locally provide 3D informations. In the first, we use crossdip analysis and interpretation of the seismic sections improved by applying the crossdip corrections to determine the orientations of the reflectors. In the second, the strikes and dips of reflectors are estimated in the crooked parts of seismic reflection profiles by estimating a measure of coherency along the traveltime trajectories defined by a particular azimuth, dip and depth, and a medium velocity. Finally, we also use the dip of reflections observed on intersecting profiles to establish the 3D orientation of reflective structures. In general, reflectors observed in the Abitibi greenstone belt and Opatica belt have strikes parallel to the deformation structures mapped at surface, suggesting that the reflectors are related to the tectonic processes which affected independently or simultaneously the two subprovinces. Most of the reflectors recovered in the Opatica belt strike ENE-WSW and dip shallowly to the north and to the south. Their attitudes coincide with the orientations of deformation fabrics associated with a N-S shortening event, which affected the belt between 2700 and 2680 Ma. Mantle reflections, previously interpreted as a relict suture of an Archean subduction zone, dip to the north at around 30°--45° and are also associated with this N-S event. Reflectors with NNE strikes and shallow dips toward the east are correlated with surface evidence for early west vergent thrusting in the Opatica crust. Mid-crustal reflectors in the Abitibi define two areas with distinctive geometry: reflectors beneath the southern Abitibi belt are oppositely-dipping, and convergent at depth, providing a V-shape aspect to the greenstone rocks, other reflectors beneath the northern Abitibi belt are, in general, similarly oriented, dipping at an average of 30° toward the north. These north-dipping reflectors are partly disrupted by a low-reflectivity zone located north of the Casa-Berardi tectonic zone at mid-crustal levels. The low reflectivity zone is attributed to rocks of the Opatica belt, located underneath the northern Abitibi greenstone belt during a late stage of the accretion of the two subprovinces. The geometry of the reflectors recovered in the Abitibi and Opatica is consistent with the different tectonic histories proposed for the two subprovinces, until common deformation during a N-S shortening event. Attitudes recovered in the northern Abitibi belt and Opatica are consistent with tectonic scenarios involving underthrusting of Abitibi middle and lower-crustal terranes beneath the Opatica belt, while the oppositely dipping reflectors recovered in the middle crust beneath the southern Abitibi belt could be representative of a rifted volcanic arc environment.

DIP1 modulates stem cell homeostasis in Drosophila through regulation of sisR-1.

PubMed

Wong, Jing Ting; Akhbar, Farzanah; Ng, Amanda Yunn Ee; Tay, Mandy Li-Ian; Loi, Gladys Jing En; Pek, Jun Wei

2017-10-02

Stable intronic sequence RNAs (sisRNAs) are by-products of splicing and regulate gene expression. How sisRNAs are regulated is unclear. Here we report that a double-stranded RNA binding protein, Disco-interacting protein 1 (DIP1) regulates sisRNAs in Drosophila. DIP1 negatively regulates the abundance of sisR-1 and INE-1 sisRNAs. Fine-tuning of sisR-1 by DIP1 is important to maintain female germline stem cell homeostasis by modulating germline stem cell differentiation and niche adhesion. Drosophila DIP1 localizes to a nuclear body (satellite body) and associates with the fourth chromosome, which contains a very high density of INE-1 transposable element sequences that are processed into sisRNAs. DIP1 presumably acts outside the satellite bodies to regulate sisR-1, which is not on the fourth chromosome. Thus, our study identifies DIP1 as a sisRNA regulatory protein that controls germline stem cell self-renewal in Drosophila.Stable intronic sequence RNAs (sisRNAs) are by-products of splicing from introns with roles in embryonic development in Drosophila. Here, the authors show that the RNA binding protein DIP1 regulates sisRNAs in Drosophila, which is necessary for germline stem cell homeostasis.

A set of 14 DIP-SNP markers to detect unbalanced DNA mixtures.

PubMed

Liu, Zhizhen; Liu, Jinding; Wang, Jiaqi; Chen, Deqing; Liu, Zidong; Shi, Jie; Li, Zeqin; Li, Wenyan; Zhang, Gengqian; Du, Bing

2018-03-04

Unbalanced DNA mixture is still a difficult problem for forensic practice. DIP-STRs are useful markers for detection of minor DNA but they are not widespread in the human genome and having long amplicons. In this study, we proposed a novel type of genetic marker, termed DIP-SNP. DIP-SNP refers to the combination of INDEL and SNP in less than 300bp length of human genome. The multiplex PCR and SNaPshot assay were established for 14 DIP-SNP markers in a Chinese Han population from Shanxi, China. This novel compound marker allows detection of the minor DNA contributor with sensitivity from 1:50 to 1:1000 in a DNA mixture of any gender with 1 ng-10 ng DNA template. Most of the DIP-SNP markers had a relatively high probability of informative alleles with an average I value of 0.33. In all, we proposed DIP-SNP as a novel kind of genetic marker for detection of minor contributor from unbalanced DNA mixture and established the detection method by associating the multiplex PCR and SNaPshot assay. DIP-SNP polymorphisms are promising markers for forensic or clinical mixture examination because they are shorter, widespread and higher sensitive. Copyright © 2018 Elsevier Inc. All rights reserved.

Research on high-temperature sensing characteristics based on modular interference of single-mode multimode single-mode fiber

NASA Astrophysics Data System (ADS)

Peng, Zhaozhuang; Wang, Li; Yan, Huanhuan

2016-11-01

Application of high temperature fiber sensing system is very extensive. It can be mainly used in high temperature test aerospace, such as, materials, chemicals, and energy. In recent years, various on-line optical fiber interferometric sensors based on modular interference of single-mode-multimode-single-mode(SMS) fiber have been largely explored in high temperature fiber sensor. In this paper we use the special fiber of a polyimide coating, its sensor head is composed of a section of multimode fiber spliced in the middle of Single-mode fiber. When the light is launched into the multimode fiber(MMF) through the lead-in single-mode fiber(SMF), the core mode and cladding modes are excited and propagate in the MMF respectively. Then, at the MMF-SMF spliced point, the excited cladding modes coupled back into the core of lead-out SMF interfere with SMF core mode. And the wavelength of the interference dip would shift differently with the variation of the temperature. By this mean, we can achieve the measurement of temperature. The experimental results also show that the fiber sensor based on SMS structure has a highly temperature sensitivity. From 30° to 300°, with the temperature increasing, the interference dip slightly shifts toward longer wavelength and the temperature sensitivity coefficient is 0.0115nm/°. With high sensitivity, simple structure, immunity to electromagnetic interferences and a good linearity of the experimental results, the structure has an excellent application prospect in engineering field.

Towards semi-automatic rock mass discontinuity orientation and set analysis from 3D point clouds

NASA Astrophysics Data System (ADS)

Guo, Jiateng; Liu, Shanjun; Zhang, Peina; Wu, Lixin; Zhou, Wenhui; Yu, Yinan

2017-06-01

Obtaining accurate information on rock mass discontinuities for deformation analysis and the evaluation of rock mass stability is important. Obtaining measurements for high and steep zones with the traditional compass method is difficult. Photogrammetry, three-dimensional (3D) laser scanning and other remote sensing methods have gradually become mainstream methods. In this study, a method that is based on a 3D point cloud is proposed to semi-automatically extract rock mass structural plane information. The original data are pre-treated prior to segmentation by removing outlier points. The next step is to segment the point cloud into different point subsets. Various parameters, such as the normal, dip/direction and dip, can be calculated for each point subset after obtaining the equation of the best fit plane for the relevant point subset. A cluster analysis (a point subset that satisfies some conditions and thus forms a cluster) is performed based on the normal vectors by introducing the firefly algorithm (FA) and the fuzzy c-means (FCM) algorithm. Finally, clusters that belong to the same discontinuity sets are merged and coloured for visualization purposes. A prototype system is developed based on this method to extract the points of the rock discontinuity from a 3D point cloud. A comparison with existing software shows that this method is feasible. This method can provide a reference for rock mechanics, 3D geological modelling and other related fields.

Nutrient budgets and trophic state in a hypersaline coastal lagoon: Lagoa de Araruama, Brazil

NASA Astrophysics Data System (ADS)

Souza, Marcelo F. L.; Kjerfve, Björn; Knoppers, Bastiaan; Landim de Souza, Weber F.; Damasceno, Raimundo N.

2003-08-01

Lagoa de Araruama in the state of Rio de Janeiro, Brazil, is a hypersaline lagoon with salinity varying spatially from 45 to 56. We collected water samples during monthly cruises throughout the lagoon, and along the streams feeding the system, from April 1991 to March 1992. Nutrients and other water quality parameters exhibited great spatial and temporal variations. Mass balance calculations indicate large amounts of anthropogenic nutrient inputs. The data indicate that the lagoon currently is oligotrophic but is in a state of transition to become a mesotrophic system. Molar dissolved inorganic nitrogen:dissolved inorganic phosphorus (DIN/DIP) varied between 2.2:1 and 659:1 with a volume-weighted average of 22:1. The high DIN/DIP ratio contrasts with that found in nearby lagoons, suggesting that phytoplankton primary production is limited by phosphorus in Lagoa de Araruama. The major loss of DIP is apparently driven by biological assimilation and diagenic reactions in the sediments. Calculations indicate that the lagoon is slightly net autotrophic at +0.9 mol C m -2 yr -1. This suggests that the biomass of the primary producers is restricted by phosphorus availability. Phosphorus retention in the sediment and the hypersaline state of the lagoon prevent changes in autotrophic communities and the formation of eutrophic conditions.

Enhanced High Performance Power Compensation Methodology by IPFC Using PIGBT-IDVR

PubMed Central

Arumugom, Subramanian; Rajaram, Marimuthu

2015-01-01

Currently, power systems are involuntarily controlled without high speed control and are frequently initiated, therefore resulting in a slow process when compared with static electronic devices. Among various power interruptions in power supply systems, voltage dips play a central role in causing disruption. The dynamic voltage restorer (DVR) is a process based on voltage control that compensates for line transients in the distributed system. To overcome these issues and to achieve a higher speed, a new methodology called the Parallel IGBT-Based Interline Dynamic Voltage Restorer (PIGBT-IDVR) method has been proposed, which mainly spotlights the dynamic processing of energy reloads in common dc-linked energy storage with less adaptive transition. The interline power flow controller (IPFC) scheme has been employed to manage the power transmission between the lines and the restorer method for controlling the reactive power in the individual lines. By employing the proposed methodology, the failure of a distributed system has been avoided and provides better performance than the existing methodologies. PMID:26613101

First observations of large-scale wave structure and equatorial spread F using CERTO radio beacon on the C/NOFS satellite

NASA Astrophysics Data System (ADS)

Thampi, S.; Yamamoto, M.; Tsunoda, R. T.; Otsuka, Y.; Tsugawa, T.; Uemoto, J.; Ishii, M.

2009-12-01

Equatorial spread F (ESF) is a generic name, which refers to the presence of a wide spectrum of field-aligned irregularities in the equatorial nighttime F-region that can extend over nearly seven orders of magnitude. Recently, a large-scale wave structure (LSWS) in the F-layer electron density is identified as a reliable precursor to ESF. The LSWS can be identified as a quasi-periodic modulation in the altitude of isoelectron density contours in the bottomside F-region, superimposed on a mean slope that increases in altitude from west to east. First observations of large-scale wave structure (LSWS) and the subsequent development of equatorial spread F (ESF), using total electron content (TEC) derived from the ground based reception of Coherent Electromagnetic Radio Tomography (CETRO) radio beacon signals on board the C/NOFS (Communications/Navigation Outage Forecasting System) satellite will be presented. For this study the TEC observations from Bac Lieu, Vietnam (9.2°N, 105.6°E geographic, 1.7°N magnetic dip latitude), Phukhet (7.8°N, 98.38°E, 0.4°S dip lat) and Kototabang, Indonesia (0.20°S, 100.32°E, 10.36°S dip lat) are analyzed along with ionosonde observations from Bac Lieu, Chumphon (10.7°N, 99.4°E, 3.3° dip lat) and 30.8 MHz VHF radar observations from Kototabang. It should also be mentioned here that LSWS is not easily detectable with overhead measurements using a sensor at a fixed location, at least not during its early growth phase, mainly because initially it grows in amplitude without significant zonal drift. The results indicate (1) LSWS appears to play a more important role in the development of ESF than the post-sunset rise (PSSR) of the F-layer, and (2) LSWS can appear well before E-region sunset. Other findings, that LSWS does not have significant zonal drift in the initial stages of growth, and can have zonal wavelengths of several hundred kilometers, corroborate earlier reports.

ON THE GEOMETRIC NATURE OF LOW-FREQUENCY QUASI-PERIODIC OSCILLATIONS IN NEUTRON-STAR LOW-MASS X-RAY BINARIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Homan, Jeroen; Remillard, Ronald A.; Fridriksson, Joel K., E-mail: jeroen@space.mit.edu

2015-10-10

We report on a detailed analysis of the so-called ∼1 Hz quasi-periodic oscillation (QPO) in the eclipsing and dipping neutron-star low-mass X-ray binary EXO 0748–676. This type of QPO has previously been shown to have a geometric origin. Our study focuses on the evolution of the QPO as the source moves through the color–color diagram in which it traces out an atoll-source-like track. The QPO frequency increases from ∼0.4 Hz in the hard state to ∼25 Hz as the source approaches the soft state. Combining power spectra based on QPO frequency reveals additional features that strongly resemble those seen inmore » non-dipping/eclipsing atoll sources. We show that the low-frequency QPOs in atoll sources and the ∼1 Hz QPO in EXO 0748–676 follow similar relations with respect to the noise components in their power spectra. We conclude that the frequencies of both types of QPOs are likely set by (the same) precession of a misaligned inner accretion disk. For high-inclination systems like EXO 0748–676 this results in modulations of the neutron-star emission due to obscuration or scattering, while for lower-inclination systems the modulations likely arise from relativistic Doppler-boosting and light-bending effects.« less

Controlling surface-segregation of a polymer to display carboxy groups on an outermost surface using perfluoroacyl groups.

PubMed

Nishimori, Keisuke; Kitahata, Shigeru; Nishino, Takashi; Maruyama, Tatsuo

2018-05-10

Controlling the surface properties of solid polymers is important for practical applications. We here succeeded in controlling the surface segregation of polymers to display carboxy groups on an outermost surface, which allowed the covalent immobilization of functional molecules via the carboxy groups on a substrate surface. Random methacrylate-based copolymers containing carboxy groups, in which carboxy groups were protected with perfluoroacyl (Rf) groups, were dip-coated on acrylic substrate surfaces. X-ray photoelectron spectroscopy and contact-angle measurements revealed that the Rf groups were segregated to the outermost surface of the dip-coated substrates. The Rf groups were removed by hydrolysis of the Rf esters in the copolymers, resulting in the display of carboxy groups on the surface. The quantification of carboxy groups on a surface revealed that the carboxy groups were reactive to a water-soluble solute in aqueous solution. The surface segregation was affected by the molecular structure of the copolymer used for dip-coating.

Enhancement of anticorrosion property of 304 stainless steel using silane coatings

NASA Astrophysics Data System (ADS)

Akhtar, Sultan; Matin, Asif; Madhan Kumar, A.; Ibrahim, Ahmed; Laoui, Tahar

2018-05-01

In the present work, silane coatings based on glycidoxypropyltrimethoxysilane/methyltrimethoxysilane (GPTMS/MTMS) and silica nanoparticles were prepared by a sol-gel method. A simple dip-coating method was applied for film deposition and the effect of immersion time and number of immersion cycles on corrosion behavior of 304 stainless steel (SS) was investigated. Scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS) was used to study the surface morphology and elemental composition of the modified surfaces. The corrosion behavior of the coated and uncoated SS substrates was studied by potentiodynamic polarization and electrochemical impedance spectroscopy in 0.6 M sodium chloride solution. Our results showed that the presence of coatings improved the anti-corrosion property of SS substrates. The coating with a dipping time of 10 min and 3 dipping cycles exhibited the best protection efficiency compared to other coatings and the uncoated substrate. SEM/EDS findings and contact angle measurements supported the conclusions drawn from the corrosion study.

Simultaneous strain and temperature sensor based on polarization maintaining fiber and multimode fiber

NASA Astrophysics Data System (ADS)

Xing, Rui; Dong, Changbin; Wang, Zixiao; Wu, Yue; Yang, Yuguang; Jian, Shuisheng

2018-06-01

A novel, simultaneous strain and temperature sensor utilizing polarization maintaining fiber (PMF) and multimode fiber (MMF) is proposed and experimentally demonstrated in this paper. The sensing head of this sensor can be obtained by splicing PMF and MMF in the structure of PMF-MMF-PMF. The extinction ratio of the transmission spectrum can be over 30 dB. The strain sensitivities of sensor by two spectrum dips can be 1.01 pm/με and 1.27 pm/με in the range from 0 to 2000 με. Meanwhile, the temperature sensitivities of 49 pm/°C and 41 pm/°C can be achieved by two spectrum dips in the range from 30 °C to 70 °C. The sensitivity difference between the two spectrum dips can be used to realize dual parameters fiber sensing. This sensor exhibits the advantages of simple fabrication, compact structure and multi-purpose measuring. It may have the great potential in fields of robot arms and artificial limbs.

Continuous coating of silicon-on-ceramic

NASA Technical Reports Server (NTRS)

Heaps, J. D.; Schuldt, S. B.; Grung, B. L.; Zook, J. D.; Butter, C. D.

1980-01-01

Growth of sheet silicon on low-cost substrates has been demonstrated by the silicon coating with inverted meniscus (SCIM) technique. A mullite-based ceramic substrate is coated with carbon and then passed over a trough of molten silicon with a raised meniscus. Solidification occurs at the trailing edge of the downstream meniscus, producing a silicon-on-ceramic (SOC) layer. Meniscus shape and stability are controlled by varying the level of molten silicon in a reservoir connected to the trough. The thermal conditions for growth and the crystallographic texture of the SOC layers are similar to those produced by dip-coating, the original technique of meniscus-controlled growth. The thermal conditions for growth have been analyzed in some detail. The analysis correctly predicts the velocity-thickness relationship and the liquid-solid interface shape for dip-coating, and appears to be equally applicable to SCIM-coating. Solar cells made from dip-coated SOC material have demonstrated efficiencies of 10% on 4-sq cm cells and 9.9% on 10-sq cm cells.

KIC 8462852: Potential Repeat of the Kepler Day 1540 Dip in 2017 August

NASA Astrophysics Data System (ADS)

Bourne, Rafik; Gary, Bruce

2017-12-01

We report 33 V-band observations by the Hereford Arizona Observatory (HAO) of the enigmatic star KIC 8462852 during the two week period 3-17 August 2017. We find a striking resemblance of these observations to the Kepler day 1540 dip with HAO observations tracking the Kepler light curve (adjusted for egress symmetry). A possible explanation of this potential repeat transit is a brown dwarf and extensive ring system in a 1601-day eccentric orbit. We suggest this object may be detectable through radial velocity observations in October and November 2017, with an amplitude of ~ 1-2 kms-1.

Synthesis of boron nitride coatings on quartz fibers: Thickness control and mechanism research

NASA Astrophysics Data System (ADS)

Zheng, Yu; Wang, Shubin

2011-10-01

Boron nitride (BN) coatings were successfully synthesized on quartz fibers by dip-coating in boric acid and urea solutions at 700 °C. The SEM micrographs indicated that the quartz fibers were fully covered by coatings with smooth surface. The XRD, FT-IR, XPS spectra and HR-TEM results showed that the composition of the coatings which combined closely with the quartz fibers was polycrystalline h-BN. By changing the dip circles, the coating thickness was well controlled. The thicknesses of samples dipped less than six circles increased linearly with dipping-circles; and the increment of coating thickness would slow down when the fibers were dipped 10 circles. After being dipped for 10 circles, the thickness was about 300 nm. The coating thickness was also established by calculation and the calculated results were consistent with the results measured by micrograph.

Blood Pressure Dipping and Urban Stressors in Young Adult African Americans.

PubMed

Mellman, Thomas A; Brown, Tyish S Hall; Kobayashi, Ihori; Abu-Bader, Soleman H; Lavela, Joseph; Altaee, Duaa; McLaughlin, Latesha; Randall, Otelio S

2015-08-01

Blunted nocturnal blood pressure (BP) dipping is an early marker of cardiovascular risk that is prevalent among African Americans. We evaluated relationships of BP dipping to neighborhood and posttraumatic stress and sleep in urban residing young adult African Americans. One hundred thirty-six black, predominately African American, men and women with a mean age of 22.9 years (SD = 4.6) filled out surveys and were interviewed and had two, 24-h ambulatory BP recordings. Thirty-eight percent had BP dipping ratios < .10. Wake after sleep onset (WASO), neighborhood disorder and neighborhood poverty rates but not posttraumatic stress symptoms, and other sleep measures correlated significantly with dipping ratios. Models with the neighborhood measures that also included WASO increased the explained variance. Studies elucidating mechanisms underlying effects of neighborhoods on BP dipping and the role of disrupted sleep, and how they can be mitigated are important directions for future research.

Blood Pressure Dipping and Urban Stressors in Young Adult African Americans

PubMed Central

Mellman, Thomas A.; Hall Brown, Tyish S.; Kobayashi, Ihori; Abu-Bader, Soleman H.; Lavela, Joseph; Altaee, Duaa; McLaughlin, Latesha; Randall, Otelio S.

2015-01-01

Background Blunted nocturnal blood pressure (BP) dipping is an early marker of cardiovascular risk that is prevalent among African Americans. Purpose We evaluated relationships of BP dipping to neighborhood and posttraumatic stress and sleep in urban residing young adult African Americans. Methods One hundred thirty six Black, predominately African American, men and women with a mean age of 22.9 (SD = 4.6) filled out surveys, were interviewed and had two, 24-hour ambulatory BP recordings. Results Thirty eight percent had BP dipping ratios < .10. Wake after sleep onset (WASO), neighborhood disorder and neighborhood poverty rates but not posttraumatic stress symptoms, and other sleep measures, correlated significantly with dipping ratios. Models with the neighborhood measures that also included WASO increased the explained variance. Conclusions Studies elucidating mechanisms underlying effects of neighborhoods on BP dipping and the role of disrupted sleep, and how they can be mitigated are important directions for future research. PMID:25623895

Effect of dipeptidyl peptidase-4 inhibition on circadian blood pressure during the development of salt-dependent hypertension in rats

PubMed Central

Sufiun, Abu; Rafiq, Kazi; Fujisawa, Yoshihide; Rahman, Asadur; Mori, Hirohito; Nakano, Daisuke; Kobori, Hiroyuki; Ohmori, Koji; Masaki, Tsutomu; Kohno, Masakazu; Nishiyama, Akira

2015-01-01

A growing body of evidence has indicated that dipeptidyl peptidase-4 (DPP-4) inhibitors have antihypertensive effects. Here, we aim to examine the effect of vildagliptin, a DPP-4-specific inhibitor, on blood pressure and its circadian-dipping pattern during the development of salt-dependent hypertension in Dahl salt-sensitive (DSS) rats. DSS rats were treated with a high-salt diet (8% NaCl) plus vehicle or vildagliptin (3 or 10 mg kg−1 twice daily by oral gavage) for 7 days. Blood pressure was measured by the telemetry system. High-salt diet for 7 days significantly increased the mean arterial pressure (MAP), systolic blood pressure (SBP) and were also associated with an extreme dipping pattern of blood pressure in DSS rats. Treatment with vildagliptin dose-dependently decreased plasma DPP-4 activity, increased plasma glucagon-like peptide 1 (GLP-1) levels and attenuated the development of salt-induced hypertension. Furthermore, vildagliptin significantly increased urine sodium excretion and normalized the dipping pattern of blood pressure. In contrast, intracerebroventricular infusion of vildagliptin (50, 500 or 2500 μg) did not alter MAP and heart rate in DSS rats. These data suggest that salt-dependent hypertension initially develops with an extreme blood pressure dipping pattern. The DPP-4 inhibitor, vildagliptin, may elicit beneficial antihypertensive effects, including the improvement of abnormal circadian blood pressure pattern, by enhancing urinary sodium excretion. PMID:25588850

Geologic map of the Leadville North 7.5’ quadrangle, Eagle and Lake Counties, Colorado

USGS Publications Warehouse

Ruleman, Chester A.; Brandt, Theodore R.; Caffee, Marc W.; Goehring, Brent M.

2018-04-24

The Leadville North 7.5’ quadrangle lies at the northern end of the Upper Arkansas Valley, where the Continental Divide at Tennessee Pass creates a low drainage divide between the Colorado and Arkansas River watersheds. In the eastern half of the quadrangle, the Paleozoic sedimentary section dips generally 20–30 degrees east. At Tennessee Pass and Missouri Hill, the core of the Sawatch anticlinorium is mapped as displaying a tight hanging-wall syncline and foot-wall anticline within the basement-cored structure. High-angle, west-dipping, Neogene normal faults cut the eastern margin of the broad, Sawatch anticlinorium. Minor displacements along high-angle, east- and west-dipping Laramide reverse faults occurred in the core of the north-plunging anticlinorium along the western and eastern flanks of Missouri Hill. Within the western half of the quadrangle, Meso- and Paleoproterozoic metamorphic and igneous rocks are uplifted along the generally east-dipping, high-angle Sawatch fault system and are overlain by at least three generations of glacial deposits in the western part of the quadrangle. 10Be and 26Al cosmogenic nuclide ages of the youngest glacial deposits indicate a last glacial maximum age of about 21–22 kilo-annum and complete deglaciation by about 14 kilo-annum, supported by chronologic studies in adjacent drainages. No late Pleistocene tectonic activity is apparent within the quadrangle.

Recent deformation along the offshore Malibu Coast, Dume, and related faults west of Point Dume, southern California

USGS Publications Warehouse

Fisher, M.A.; Langenheim, V.E.; Sorlien, C.C.; Dartnell, P.; Sliter, R.W.; Cochrane, G.R.; Wong, F.L.

2005-01-01

Offshore faults west of Point Dume, southern California, are part of an important regional fault system that extends for about 206 km, from near the city of Los Angeles westward along the south flank of the Santa Monica Mountains and through the northern Channel Islands. This boundary fault system separates the western Transverse Ranges, on the north, from the California Continental Borderland, on the south. Previous research showed that the fault system includes many active fault strands; consequently, the entire system is considered a serious potential earthquake hazard to nearby Los Angeles. We present an integrated analysis of multichannel seismic- and high-resolution seismic-reflection data and multibeam-bathymetric information to focus on the central part of the fault system that lies west of Point Dume. We show that some of the main offshore faults have cumulative displacements of 3-5 km, and many faults are currently active because they deform the seafloor or very shallow sediment layers. The main offshore fault is the Dume fault, a large north-dipping reverse fault. In the eastern part of the study area, this fault offsets the seafloor, showing Holocene displacement. Onshore, the Malibu Coast fault dips steeply north, is active, and shows left-oblique slip. The probable offshore extension of this fault is a large fault that dips steeply in its upper part but flattens at depth. High-resolution seismic data show that this fault deforms shallow sediment making up the Hueneme fan complex, indicating Holocene activity. A structure near Sycamore knoll strikes transversely to the main faults and could be important to the analysis of the regional earthquake hazard because the structure might form a boundary between earthquake-rupture segments.

Measurement of Local Partial Pressure of Oxygen in the Brain Tissue under Normoxia and Epilepsy with Phosphorescence Lifetime Microscopy

PubMed Central

Zhang, Cong; Bélanger, Samuel; Pouliot, Philippe; Lesage, Frédéric

2015-01-01

In this work a method for measuring brain oxygen partial pressure with confocal phosphorescence lifetime microscopy system is reported. When used in conjunction with a dendritic phosphorescent probe, Oxyphor G4, this system enabled minimally invasive measurements of oxygen partial pressure (pO2) in cerebral tissue with high spatial and temporal resolution during 4-AP induced epileptic seizures. Investigating epileptic events, we characterized the spatio-temporal distribution of the "initial dip" in pO2 near the probe injection site and along nearby arterioles. Our results reveal a correlation between the percent change in the pO2 signal during the "initial dip" and the duration of seizure-like activity, which can help localize the epileptic focus and predict the length of seizure. PMID:26305777

Imaging the complexity of an active normal fault system: The 1997 Colfiorito (central Italy) case study

USGS Publications Warehouse

Chiaraluce, L.; Ellsworth, W.L.; Chiarabba, C.; Cocco, M.

2003-01-01

Six moderate magnitude earthquakes (5 < Mw < 6) ruptured normal fault segments of the southern sector of the North Apennine belt (central Italy) in the 1997 Colfiorito earthquake sequence. We study the progressive activation of adjacent and nearby parallel faults of this complex normal fault system using ???1650 earthquake locations obtained by applying a double-difference location method, using travel time picks and waveform cross-correlation measurements. The lateral extent of the fault segments range from 5 to 10 km and make up a broad, ???45 km long, NW trending fault system. The geometry of each segment is quite simple and consists of planar faults gently dipping toward SW with an average dip of 40??-45??. The fault planes are not listric but maintain a constant dip through the entire seismogenic volume, down to 8 km depth. We observe the activation of faults on the hanging wall and the absence of seismicity in the footwall of the structure. The observed fault segmentation appears to be due to the lateral heterogeneity of the upper crust: preexisting thrusts inherited from Neogene's compressional tectonic intersect the active normal faults and control their maximum length. The stress tensor obtained by inverting the six main shock focal mechanisms of the sequence is in agreement with the tectonic stress active in the inner chain of the Apennine, revealing a clear NE trending extension direction. Aftershock focal mechanisms show a consistent extensional kinematics, 70% of which are mechanically consistent with the main shock stress field.

Phosphate oxygen isotope ratios as a tracer for sources and cycling of phosphate in North San Francisco Bay, California

USGS Publications Warehouse

McLaughlin, K.; Kendall, C.; Silva, S.R.; Young, M.; Paytan, A.

2006-01-01

A seasonal analysis assesing variations in the oxygen isotopic composition of dissolved inorganic phosphate (DIP) was conducted in the San Francisco Bay estuarine system, California. Isotopic fractionation of oxygen in DIP (exchange of oxygen between phosphate and environmental water) at surface water temperatures occurs only as a result of enzyme-mediated, biological reactions. Accordingly, if phospate demand is low relative to input and phosphate is not heavily cycled in the ecosystem, the oxygen isotopic composition of DIP (?? 18Op) will reflect the isotopic composition of the source of phosphate to the system. Such is the case for the North San Francisco Bay, an anthropogenically impacted estuary with high surface water phosphate concentrations. Variability in the ?? 18Op in the bay is primarily controlled by mixing of water masses with different ??18Op signatures. The ??18Op values range from 11.4??? at the Sacramento River to 20.1??? at the Golden Gate. Deviations from the two-component mixing model for the North Bay reflect additional, local sources of phosphate to the estuary that vary seasonally. Most notably, deviations from the mixing model occur at the confluence of a major river into the bay during periods of high river discharge and near wastewater treatment outlets. These data suggest that ??18Op can be an effective tool for identifying P point sources and understanding phosphate dynamics in estuarine systems. Copyright 2006 by the American Geophysical Union.

Influence of non-dipping pattern of blood pressure in gestational hypertension on maternal cardiac function, hemodynamics and intrauterine growth restriction.

PubMed

Ilic, A; Ilic, D J; Tadic, S; Stefanovic, M; Stojsic-Milosavljevic, A; Pavlovic, K; Redzek, A; Velicki, L

2017-10-01

An association between gestational hypertension (GH) and changes of maternal cardiac function was previously reported. The study assessed the effect of non-dipping pattern of blood pressure (BP) in GH on haemodynamic function and intrauterine growth restriction (IUGR). This study included 126 women (91 with GH and 35 normotensive controls). Based on the BP values measured by ambulatory blood pressure monitoring (ABPM), all hypertensive women were classified in dipper (46 women) or in non-dipper group (45 women). All participants underwent echocardiography and ABPM during the third trimester. Participants with GH and non-dipping pattern had significantly lower velocity of longitudinal systolic function (s') (p<0.0005), and cardiac output index (COi) compared to dippers (p<0.0005) and controls (p=0.002). Diastolic velocities at the mitral valve annulus were also lower in non-dippers e's (non-dippers vs dippers p=0.023; non-dippers vs controls p<0.0005) and e'l (non-dippers vs dippers p=0.048; non-dippers vs controls p<0.0005). There were significant differences in the index of the left ventricle filling pressure E/e' and myocardial mass index between women with GH and controls, but with no significant difference among dippers and non-dippers. Total vascular resistance was increased in non-dipping group compared to normotensives and dippers (p<0.0005). Multivariate regression analysis revealed that the peak night-time diastolic BP, left ventricular mass index and CO index were identified as independent predictors of IUGR. Changes in maternal hemodynamics, as well as IUGR, are strongly related to the non-dipping pattern of BP. Copyright © 2017 International Society for the Study of Hypertension in Pregnancy. Published by Elsevier B.V. All rights reserved.

Detection of integrated papillomavirus sequences by ligation-mediated PCR (DIPS-PCR) and molecular characterization in cervical cancer cells.

PubMed

Luft, F; Klaes, R; Nees, M; Dürst, M; Heilmann, V; Melsheimer, P; von Knebel Doeberitz, M

2001-04-01

Human papillomavirus (HPV) genomes usually persist as episomal molecules in HPV associated preneoplastic lesions whereas they are frequently integrated into the host cell genome in HPV-related cancers cells. This suggests that malignant conversion of HPV-infected epithelia is linked to recombination of cellular and viral sequences. Due to technical limitations, precise sequence information on viral-cellular junctions were obtained only for few cell lines and primary lesions. In order to facilitate the molecular analysis of genomic HPV integration, we established a ligation-mediated PCR assay for the detection of integrated papillomavirus sequences (DIPS-PCR). DIPS-PCR was initially used to amplify genomic viral-cellular junctions from HPV-associated cervical cancer cell lines (C4-I, C4-II, SW756, and HeLa) and HPV-immortalized keratinocyte lines (HPKIA, HPKII). In addition to junctions already reported in public data bases, various new fusion fragments were identified. Subsequently, 22 different viral-cellular junctions were amplified from 17 cervical carcinomas and 1 vulval intraepithelial neoplasia (VIN III). Sequence analysis of each junction revealed that the viral E1 open reading frame (ORF) was fused to cellular sequences in 20 of 22 (91%) cases. Chromosomal integration loci mapped to chromosomes 1 (2n), 2 (3n), 7 (2n), 8 (3n), 10 (1n), 14 (5n), 16 (1n), 17 (2n), and mitochondrial DNA (1n), suggesting random distribution of chromosomal integration sites. Precise sequence information obtained by DIPS-PCR was further used to monitor the monoclonal origin of 4 cervical cancers, 1 case of recurrent premalignant lesions and 1 lymph node metastasis. Therefore, DIPS-PCR might allow efficient therapy control and prediction of relapse in patients with HPV-associated anogenital cancers. Copyright 2001 Wiley-Liss, Inc.

Sol-gel dip coating of yttria-stabilized tetragonal zirconia dental ceramic by aluminosilicate nanocomposite as a novel technique to improve the bonding of veneering porcelain.

PubMed

Madani, Azamsadat; Nakhaei, Mohammadreza; Karami, Parisa; Rajabzadeh, Ghadir; Salehi, Sahar; Bagheri, Hossein

2016-01-01

The aim of this in vitro study was to evaluate the effect of silica and aluminosilicate nanocomposite coating of zirconia-based dental ceramic by a sol-gel dip-coating technique on the bond strength of veneering porcelain to the yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in vitro. Thirty Y-TZP blocks (10 mm ×10 mm ×3 mm) were prepared and were assigned to four experimental groups (n=10/group): C, without any further surface treatment as the control group; S, sandblasted using 110 μm alumina powder; Si, silica sol dip coating + calcination; and Si/Al, aluminosilicate sol dip coating + calcination. After preparing Y-TZP samples, a 3 mm thick layer of the recommended porcelain was fired on the coated Y-TZP surface. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analysis were used to characterize the coating and the nature of the bonding between the coating and zirconia. To examine the zirconia-porcelain bond strength, a microtensile bond strength (μTBS) approach was chosen. FT-IR study showed the formation of silica and aluminosilicate materials. XRD pattern showed the formation of new phases consisting of Si, Al, and Zr in coated samples. SEM showed the formation of a uniform coating on Y-TZP samples. Maximum μTBS values were obtained in aluminosilicate samples, which were significantly increased compared to control and sandblasted groups (P=0.013 and P<0.001, respectively). This study showed that aluminosilicate sol-gel dip coating can be considered as a convenient, less expensive reliable method for improving the bond strength between dental Y-TZP ceramics and veneering porcelain.

Sol–gel dip coating of yttria-stabilized tetragonal zirconia dental ceramic by aluminosilicate nanocomposite as a novel technique to improve the bonding of veneering porcelain

PubMed Central

Madani, Azamsadat; Nakhaei, Mohammadreza; Karami, Parisa; Rajabzadeh, Ghadir; Salehi, Sahar; Bagheri, Hossein

2016-01-01

The aim of this in vitro study was to evaluate the effect of silica and aluminosilicate nanocomposite coating of zirconia-based dental ceramic by a sol–gel dip-coating technique on the bond strength of veneering porcelain to the yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in vitro. Thirty Y-TZP blocks (10 mm ×10 mm ×3 mm) were prepared and were assigned to four experimental groups (n=10/group): C, without any further surface treatment as the control group; S, sandblasted using 110 μm alumina powder; Si, silica sol dip coating + calcination; and Si/Al, aluminosilicate sol dip coating + calcination. After preparing Y-TZP samples, a 3 mm thick layer of the recommended porcelain was fired on the coated Y-TZP surface. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analysis were used to characterize the coating and the nature of the bonding between the coating and zirconia. To examine the zirconia–porcelain bond strength, a microtensile bond strength (μTBS) approach was chosen. FT-IR study showed the formation of silica and aluminosilicate materials. XRD pattern showed the formation of new phases consisting of Si, Al, and Zr in coated samples. SEM showed the formation of a uniform coating on Y-TZP samples. Maximum μTBS values were obtained in aluminosilicate samples, which were significantly increased compared to control and sandblasted groups (P=0.013 and P<0.001, respectively). This study showed that aluminosilicate sol–gel dip coating can be considered as a convenient, less expensive reliable method for improving the bond strength between dental Y-TZP ceramics and veneering porcelain. PMID:27478376

Probable Mid-Miocene Caldera in the Modoc Plateau, Northeast California

NASA Astrophysics Data System (ADS)

Bowens, T. E.; Grose, T. L.

2001-12-01

Regional geologic mapping within the Modoc Plateau has resulted in the discovery of a large volcanotectonic anomaly some 21-km in diameter approximately 50-km WSW of the city of Alturas in Modoc County, California. Centrally located within this anomaly lies a structural depression some 11-km in diameter which, based on structural, lithologic, and geophysical characteristics, is believed to represent a deeply eroded mid-Miocene caldera. The region extending outward some 5-km from the proposed caldera displays a sharp, localized structural deflection from a NNW to a WNW structural grain. Lying inboard of this deflection, a series of regionally discordant E-W to NE trending, generally down to the north, normal faults were discovered which are believed to represent rim faults to an ancient caldera. Bedding within the hanging wall of these discordant structures displays highly contorted and regionally anomalous dips. By stereographic removal of the regional northeast dip overprinting the area, the anomalous dips were found to display a radial, steeply inward dipping pattern in close proximity to the proposed rim structures while dips located further inboard are generally flat-lying. Lithologies within the proposed caldera are regionally anomalous and include abundant tuffaceous and flow dominated breccias, closed basin organic sedimentary facies, and an anomalous concentration of volcanic centers of both mafic and felsic compositions. One of these intrusives was age dated at 12.9 Ma indicating the anomaly formed during mid-Miocene time. The location of the proposed caldera is associated with a +20 mgal gravity high, which stands in contrast to a lesser high of +10 mgal associated with the Medicine Lake Caldera some 50-km to the northwest. This combination of structural, lithologic, and geophysical evidence leads to the interpretation of a caldera at this location, herein termed the Stone Coal Valley Caldera.

Differential Growth Responses of Marine Phytoplankton to Herbicide Glyphosate

PubMed Central

Wang, Cong; Lin, Xin; Li, Ling; Lin, Senjie

2016-01-01

Glyphosate is a globally popular herbicide to kill weeds and its wide applications may lead to accumulation in coastal oceans as a source of phosphorus (P) nutrient or growth inhibitor of phytoplankton. We studied the physiological effects of glyphosate on fourteen species representing five major coastal phytoplankton phyla (haptophyta, bacillariophyta, dinoflagellata, raphidophyta, and chlorophyta). Based on growth responses to different concentrations of glyphosate under contrasting dissolved inorganic phosphorus (DIP) conditions, we found that phytoplankton species could be classified into five groups. Group I (Emiliania huxleyi, Skeletonema costatum, Phaeodactylum tricornutum) could utilize glyphosate as sole P-source to support growth in axenic culture, but in the presence of DIP, they were inhibited by both 36-μM and 360-μM glyphosate. Group II (Karenia mikimotoi, Prorocentrum minimum, Dunaliella tertiolecta, Symbiodinium sp., Heterosigma akashiwo and Alexandrium catenella) could not utilize glyphosate as sole P-source to support growth, and in the presence of DIP growth was not affected by 36-μM but inhibited by 360-μM glyphosate. Glyphosate consistently enhanced growth of Group III (Isochrysis galbana) and inhibited Group IV (Thalassiosira weissflogii, Thalassiosira pseudonana and Chattonella marina) regardless of DIP condition. Group V (Amphidinium carterae) exhibited no measurable response to glyphosate regardless of DIP condition. This grouping is not congruent with the phylogenetic relationships of the phytoplankton species suggesting functional differentiation driven by environmental pressure. We conclude that glyphosate could be used as P-source by some species while is toxic to some other species and yet has no effects on others. The observed differential effects suggest that the continued use of glyphosate and increasing concentration of this herbicide in the coastal waters will likely exert significant impact on coastal marine phytoplankton community structure. PMID:26985828

Geometry of Thrust Faults Beneath Amenthes Rupes, Mars

NASA Technical Reports Server (NTRS)

Vidal, A.; Mueller, K. M.; Golombek, M. P.

2005-01-01

Amenthes Rupes is a 380 km-long lobate fault scarp located in the eastern hemisphere of Mars near the dichotomy boundary. The scarp is marked by about 1 km of vertical separation across a northeast dipping thrust fault (top to the SW) and offsets heavily-cratered terrain of Late Noachian age, the visible portion of which was in place by 3.92 Ga and the buried portion in place between 4.08 and 4.27 Ga. The timing of scarp formation is difficult to closely constrain. Previous geologic mapping shows that near the northern end of Amenthes Rupes, Hesperian age basalts terminate at the scarp, suggesting that fault slip predated the emplacement of these flows at 3.69 to 3.9 Ga. Maxwell and McGill also suggest the faulting ceased before the final emplacement of the Late Hesperian lavas on Isidis Planitia. The trend of the faults at Amenthes, like many thrust faults at the dichotomy boundary, parallels the boundary itself. Schultz and Watters used a dislocation modeling program to match surface topography and vertical offset of the scarp at Amenthes Rupes, varying the dip and depth of faulting, assuming a slip of 1.5 km on the fault. They modeled faulting below Amenthes Rupes as having a dip of between 25 and 30 degrees and a depth of 25 to 35 km, based on the best match to topography. Assuming a 25 degree dip and surface measurements of vertical offset of between 0.3 and 1.2 km, Watters later estimated the maximum displacement on the Amenthes Rupes fault to be 2.90 km. However, these studies did not determine the geometry of the thrust using quantitative constraints that included shortening estimates. Amenthes Rupes deforms large preexisting impact craters. We use these craters to constrain shortening across the scarp and combine this with vertical separation to infer fault geometry. Fault dip was also estimated using measurements of scarp morphology. Measurements were based on 460 m (1/128 per pixel) digital elevation data from the Mars Orbiter Laser Altimeter (MOLA), an instrument on the Mars Global Surveyor (MGS) satellite.

Building beef cow nutritional programs with the 1996 NRC beef cattle requirements model.

PubMed

Lardy, G P; Adams, D C; Klopfenstein, T J; Patterson, H H

2004-01-01

Designing a sound cow-calf nutritional program requires knowledge of nutrient requirements, diet quality, and intake. Effectively using the NRC (1996) beef cattle requirements model (1996NRC) also requires knowledge of dietary degradable intake protein (DIP) and microbial efficiency. Objectives of this paper are to 1) describe a framework in which 1996NRC-applicable data can be generated, 2) describe seasonal changes in nutrients on native range, 3) use the 1996NRC to predict nutrient balance for cattle grazing these forages, and 4) make recommendations for using the 1996NRC for forage-fed cattle. Extrusa samples were collected over 2 yr on native upland range and subirrigated meadow in the Nebraska Sandhills. Samples were analyzed for CP, in vitro OM digestibility (IVOMD), and DIP. Regression equations to predict nutrients were developed from these data. The 1996NRC was used to predict nutrient balances based on the dietary nutrient analyses. Recommendations for model users were also developed. On subirrigated meadow, CP and IVOMD increased rapidly during March and April. On native range, CP and IVOMD increased from April through June but decreased rapidly from August through September. Degradable intake protein (DM basis) followed trends similar to CP for both native range and subirrigated meadow. Predicted nutrient balances for spring- and summer-calving cows agreed with reported values in the literature, provided that IVOMD values were converted to DE before use in the model (1.07 x IVOMD - 8.13). When the IVOMD-to-DE conversion was not used, the model gave unrealistically high NE(m) balances. To effectively use the 1996NRC to estimate protein requirements, users should focus on three key estimates: DIP, microbial efficiency, and TDN intake. Consequently, efforts should be focused on adequately describing seasonal changes in forage nutrient content. In order to increase use of the 1996NRC, research is needed in the following areas: 1) cost-effective and accurate commercial laboratory procedures to estimate DIP, 2) reliable estimates or indicators of microbial efficiency for various forage types and qualities, 3) improved estimates of dietary TDN for forage-based diets, 4) validation work to improve estimates of DIP and MP requirements, and 5) incorporation of nitrogen recycling estimates.

The breeding behavior of Glyphoglossus molossus and the tadpoles of Glyphoglossus molossus and Calluella guttulata (Microhylidae).

PubMed

Altig, Ronald; Rowley, Jodi J L

2014-06-04

The breeding behavior of Glyphoglossus molossus is described from still and video images taken in Cambodia. These large, burrowing frogs follow the general theme of microhylids that deposit aquatic eggs: explosive breeding in ephemeral water and performing multiple amplectic dips to oviposit surface films of pigmented eggs. A portion of a clutch is released with each dip, a dip lasts for about 6 s, 200-300 eggs are released per dip, and about 5 s pass between dips. The ova have a dark black animal pole and yellow vegetal pole. Expanded datasets on the morphology of the tadpoles of Glyphoglossus from Vietnam and Calluella from Myanmar are presented. 

The Association of Pediatric Obesity With Nocturnal Non-Dipping on 24-Hour Ambulatory Blood Pressure Monitoring.

PubMed

Macumber, Ian R; Weiss, Noel S; Halbach, Susan M; Hanevold, Coral D; Flynn, Joseph T

2016-05-01

Obesity has been linked with abnormal nocturnal dipping of blood pressure (BP) in adults, which in turn is associated with poor cardiovascular outcomes. There are few data regarding abnormal dipping status in the obese pediatric population. The goal of this study was to further describe the relationship between obesity and non-dipping status on ambulatory blood pressure monitor (ABPM) in children. We conducted a cross-sectional study using a database of patients aged 5-21 years who had undergone 24-hour ABPM at Seattle Children's Hospital from January 2008 through May 2014. Subjects were grouped by body mass index (BMI) into lean (BMI 15th-85th percentile) and obese (BMI >95th percentile) groups. Compared to lean subjects (n = 161), obese subjects (n = 247) had a prevalence ratio (PR) for non-dipping of 2.15, adjusted for race (95% confidence interval (CI) = 1.25-3.42). Increasing severity of obesity was not further associated with nocturnal non-dipping. Nocturnal non-dipping was not associated with left ventricular hypertrophy (PR = 1.01, 95% CI = 0.71-1.44). These results suggest that in children, just as in adults, obesity is related to a relatively decreased dipping in nocturnal BP. © American Journal of Hypertension, Ltd 2015. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Tremor pattern differentiates drug-induced resting tremor from Parkinson disease.

PubMed

Nisticò, R; Fratto, A; Vescio, B; Arabia, G; Sciacca, G; Morelli, M; Labate, A; Salsone, M; Novellino, F; Nicoletti, A; Petralia, A; Gambardella, A; Zappia, M; Quattrone, A

2016-04-01

DAT-SPECT, is a well-established procedure for distinguishing drug-induced parkinsonism from Parkinson's disease (PD). We investigated the usefulness of blink reflex recovery cycle (BRrc) and of electromyographic parameters of resting tremor for the differentiation of patients with drug-induced parkinsonism with resting tremor (rDIP) from those with resting tremor due to PD. This was a cross-sectional study. In 16 patients with rDIP and 18 patients with PD we analysed electrophysiological parameters (amplitude, duration, burst and pattern) of resting tremor. BRrc at interstimulus intervals (ISI) of 100, 150, 200, 300, 400, 500 and 750 msec was also analysed in patients with rDIP, patients with PD and healthy controls. All patients and controls underwent DAT-SPECT. Rest tremor amplitude was higher in PD patients than in rDIP patients (p < 0.001), while frequency and burst duration were higher in rDIP than in PD (p < 0.001, p < 0.003, respectively). Resting tremor showed a synchronous pattern in all patients with rDIP, whereas it had an alternating pattern in all PD patients (p < 0.001). DAT-SPECT was normal in rDIP patients while it was markedly abnormal in patients with PD. In the absence of DAT-SPECT, the pattern of resting tremor can be considered a useful investigation for differentiating rDIP from PD. Copyright © 2016. Published by Elsevier Ltd.

Development of advanced Czochralski growth process to produce low cost 150 kg silicon ingots from a single crucible for technology readiness

NASA Technical Reports Server (NTRS)

1981-01-01

The process development continued, with a total of nine crystal growth runs. One of these was a 150 kg run of 5 crystals of approximately 30 kg each. Several machine and process problems were corrected and the 150 kg run was as successful as previous long runs on CG2000 RC's. The accelerated recharge and growth will be attempted when the development program resumes at full capacity in FY '82. The automation controls (Automatic Grower Light Computer System) were integrated to the seed dip temperature, shoulder, and diameter sensors on the CG2000 RC development grower. Test growths included four crystals, which were grown by the computer/sensor system from seed dip through tail off. This system will be integrated on the Mod CG2000 grower during the next quarter. The analytical task included the completion and preliminary testing of the gas chromatograph portion of the Furnace Atmosphere Analysis System. The system can detect CO concentrations and will be expanded to oxygen and water analysis in FY '82.

Preparation, characterization, and biological properties of organic-inorganic nanocomposite coatings on titanium substrates prepared by sol-gel.

PubMed

Catauro, Michelina; Bollino, Flavia; Papale, Ferdinando

2014-02-01

When surface-reactive (bioactive) coatings are applied to medical implants by means of the sol-gel dip-coating technique, the biological proprieties of the surface of the implant can be locally modified to match the properties of the surrounding tissues to provide a firm fixation of the implant. The aim of this study has been to synthesize, via sol-gel, organoinorganic nanoporous materials and to dip-coat a substrate to use in dental applications. Different systems have been prepared consisting of an inorganic zirconium-based matrix, in which a biodegradable polymer, the poly-ε-caprolactone was incorporated in different percentages. The materials synthesized by the sol-gel process, before gelation, when they were still in sol phase, have been used to coat a titanium grade 4 (Ti-4) substrate to change its surface biological properties. Thin films have been obtained by means of the dip-coating technique. A microstructural analysis of the obtained coatings was performed using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy. The biological proprieties have been investigated by means of tests in vitro. The bone-bonding capability of the nanocomposite films has been evaluated by examining the appearance of apatite on their surface when plunged in a simulated body fluid (SBF) with ion concentrations nearly equal to those of human blood plasma. The examination of apatite formation on the nanocomposites, after immersion in SBF, has been carried out by SEM equipped with energy-dispersive X-ray spectroscopy. To evaluate cells-materials interaction, human osteosarcoma cell line (Saos-2) has been seeded on specimens and cell vitality evaluated by WST-8 assay. © 2013 Wiley Periodicals, Inc.

Assessment of Late Quaternary strain partitioning in the Afar Triple Junction: Dobe and Hanle grabens, Ethiopia and Djibouti

NASA Astrophysics Data System (ADS)

Polun, S. G.; Stockman, M. B.; Hickcox, K.; Horrell, D.; Tesfaye, S.; Gomez, F. G.

2015-12-01

As the only subaerial exposure of a ridge - ridge - ridge triple junction, the Afar region of Ethiopia and Djibouti offers a rare opportunity to assess strain partitioning within this type of triple junction. Here, the plate boundaries do not link discretely, but rather the East African rift meets the Red Sea and Gulf of Aden rifts in a zone of diffuse normal faulting characterized by a lack of magmatic activity, referred to as the central Afar. An initial assessment of Late Quaternary strain partitioning is based on faulted landforms in the Dobe - Hanle graben system in Ethiopia and Djibouti. These two extensional basins are connected by an imbricated accommodation zone. Several fault scarps occur within terraces formed during the last highstand of Lake Dobe, around 5 ka - they provide a means of calibrating a numerical model of fault scarp degradation. Additional timing constraints will be provided by pending exposure ages. The spreading rates of both grabens are equivalent, however in Dobe graben, extension is partitioned 2:1 between northern, south dipping faults and the southern, north dipping fault. Extension in Hanle graben is primarily focused on the north dipping Hanle fault. On the north margin of Dobe graben, the boundary fault bifurcates, where the basin-bordering fault displays a significantly higher modeled uplift rate than the more distal fault, suggesting a basinward propagation of faulting. On the southern Dobe fault, surveyed fault scarps have ages ranging from 30 - 5 ka with uplift rates of 0.71, 0.47, and 0.68 mm/yr, suggesting no secular variation in slip rates from the late Plestocene through the Holocene. These rates are converted into horizontal stretching estimates, which are compared with regional strain estimated from velocities of relatively sparse GPS data.

A striking mobility improvement of C60 OFET by inserting diindenoperylene layer between C60 and SiO2 gate insulator

NASA Astrophysics Data System (ADS)

Yang, Jin-peng; Yonezawa, Keiichiro; Hinderhofer, Alexander; Bussolotti, Fabio; Kera, Satoshi; Ueno, Nobuo

2014-09-01

Gap states in organic semiconductors play a crucial role in determining Energy-Level Alignment and in many cases they act as charge trapping centers to result in serious lowering of charge mobility. Thus origin of gap states has gained increasing attention in order to realize higher mobility organic devises [1-4]. Bussolotti et al. have demonstrated recently that gap states in a pentacene thin film increase even by exposing the film to inert gas and confirmed that the gas exposure mediates structural defects in the film thus gap states [4]. The results have also indicated that preparation of highly-ordered organic thin film is necessary to improve the device performance, namely to decrease trapping states. To improve the ordering of molecule in the film, deposition of a template molecular underlayer is one of the simplest methods to increase the domain size of overlayer film and its crystallinity, and thus we expect improvement of the charge mobility [5]. Hinderhofer et al. reported recently that diindenoperylene (DIP; Figure 1a) could be used as a template layer to grow highly ordered and oriented C60 film with its (111) plane parallel to the SiO2 substrate [6]. Considering the hole mobility of DIP single crystal, which is quite low (~0.005 cm2 V-1S-1 at room temperature [7]), it is expected for the DIP template C60 thin film system that lower drain current would be achieved to improve the on/off ratios based on n type C60 transistor and its electron mobility (especially on the negative Vgs region, compared to PEN modified C60 transistors [8]).

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sprinklers; or (ii) An automatic fire-extinguishing system conforming to the requirements of subpart L of... the alarm set point, you must equip the tank with a circulating cooling system. (5) If the tank has a bottom drain, the bottom drain may be combined with the oil-circulating system. (6) You must not use air...

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... sprinklers; or (ii) An automatic fire-extinguishing system conforming to the requirements of subpart L of... the alarm set point, you must equip the tank with a circulating cooling system. (5) If the tank has a bottom drain, the bottom drain may be combined with the oil-circulating system. (6) You must not use air...

A miniaturised image based fluorescence detection system for point-of-care-testing of cocaine abuse

NASA Astrophysics Data System (ADS)

Walczak, Rafał; Krüger, Jan; Moynihan, Shane

2015-08-01

In this paper, we describe a miniaturised image-based fluorescence detection system and demonstrate its viability as a highly sensitive tool for point-of-care-analysis of drugs of abuse in human sweat with a focus on monitor individuals for drugs of abuse. Investigations of miniaturised and low power optoelectronic configurations and methodologies for real-time image analysis were successfully carried out. The miniaturised fluorescence detection system was validated against a reference detection system under controlled laboratory conditions by analysing spiked sweat samples in dip stick and then strip with sample pad. As a result of the validation studies, a 1 ng mL-1 limit of detection of cocaine in sweat and full agreement of test results with the reference detection system can be reported. Results of the investigations open the way towards a detection system that integrates a hand-held fluorescence reader and a wearable skinpatch, and which can collect and in situ analyse sweat for the presence of cocaine at any point for up to tenths hours.

Nocturnal blood pressure non-dipping is not associated with increased left ventricular mass index in hypertensive children without end-stage renal failure.

PubMed

Seeman, Tomáš; Hradský, Ondřej; Gilík, Jiří

2016-08-01

The aim of our study was to investigate whether nocturnal blood pressure (BP) dip is associated with increased left ventricular mass index and hypertrophy in children with hypertension (HT). We retrospectively reviewed data from all children with confirmed ambulatory HT in our center and performed ambulatory blood pressure monitoring (ABPM) and echocardiography at the same time. Left ventricular hypertrophy (LVH) was defined as left ventricular mass index (LVMI) ≥95th centile. Non-dipping phenomenon was defined as nocturnal BP dip <10 %. A total of 114 ABPM studies were included, the median age of children was 15.3 years (3.8-18.9), 80 children had renoparenchymal HT without end-stage renal failure, 34 had primary HT, and 27 studies were done on untreated children and 87 on treated children. Non-dipping phenomenon was present in 63 (55 %) studies (non-dippers). The LVMI adjusted for age was not significantly different between non-dippers and dippers (0.87 ± 0.03 vs. 0.81 ± 0.02, p = 0.13). Left ventricular hypertrophy was not significantly higher in non-dippers than in dippers (20 vs. 9 %, p = 0.12). Hypertensive children without end-stage renal failure with non-dipping phenomenon do not have increased prevalence of LVH or higher LVMI adjusted for age than hypertensive children with preserved nocturnal BP dip. • Adult and pediatric hypertensive patients with end-stage renal failure have often nocturnal blood pressure non-dipping phenomenon. • Non-dipping phenomenon is in patients with end-stage renal failure associated with increased prevalence of left ventricular hypertrophy. What is New: • Pediatric hypertensive patients without end-stage renal failure with blood pressure non-dipping phenomenon do not have increased prevalence of left ventricular hypertrophy.

ASCA Observation of the Dipping X-Ray Source X1916-053

NASA Technical Reports Server (NTRS)

Ko, Yuan-Kuen; Makai, Koji; Smale, Alan P.; White, Nick E.

1997-01-01

We present the results of timing and spectral studies of the dipping X-ray source X1916-053, observed by ASCA during its Performance Verification phase. The detected dipping activity is consistent with previous observations, with a period of 3008s and an intermittent secondary dip observed roughly 0.4 out of phase with the primary dip. The energy spectra of different intensity states are fitted with a power law with partial covering fraction absorption and interstellar absorption. The increase in the hardness ratio during the primary and secondary dips, and the increase in the covering fraction and column density with decreasing X-ray intensity, all imply that the dipping is caused by the photo-absorbing materials which have been suggested to be where the accreted flow hits the outer edge of the disk materials. The spectra at all intensity levels show no apparent evidence for Fe or Ne emission lines. This may be due to the low metal abundance in the accretion flow. Alternatively, the X-ray luminosity of the central source may be too weak to excite emission lines, which are assumed to be produced by X-ray photoionization of the disk materials.

Morphology evaluation of ZrO2 dip coating on mild steel and its corrosion performance in NaOH solution

NASA Astrophysics Data System (ADS)

Anwar, M. A.; Kurniawan, T.; Asmara, Y. P.; Harun, W. S. W.; Oumar, A. N.; Nandyanto, A. B. D.

2017-10-01

In this work, the morphology of ZrO2 thin film from dip coating process on mild steel has been investigated. Mild steel was dip-coated on solution made of zirconium butoxide as a precursor, ethanol as solvent, acetylacetone as chelating agent and water for hydrolysis. Number of dipping was adjusted at 3, 5 and 7 times. The dipped sample then annealed at 350°C for two hours by adjusting the heating rate at 1°C/min respectively. The optical microscope showed that micro-cracks were observed on the surface of the coating with its concentration reduced as dipping sequence increased. The XRD result showed that annealing process can produce polycrystalline tetragonal-ZrO2. Meanwhile, SEM image showed that the thicknesses of the ZrO2 coatings were in between 400-600 nm. The corrosion resistance of uncoated and coated substrates was studied by polarization test through potentio-dynamic polarization curve at 1mV/s immersed in with 3.5% NaCl. The coating efficiency was improved as the number of layer dip coated increased, which showed improvement in corrosion protection.

Iterative dip-steering median filter

NASA Astrophysics Data System (ADS)

Huo, Shoudong; Zhu, Weihong; Shi, Taikun

2017-09-01

Seismic data are always contaminated with high noise components, which present processing challenges especially for signal preservation and its true amplitude response. This paper deals with an extension of the conventional median filter, which is widely used in random noise attenuation. It is known that the standard median filter works well with laterally aligned coherent events but cannot handle steep events, especially events with conflicting dips. In this paper, an iterative dip-steering median filter is proposed for the attenuation of random noise in the presence of multiple dips. The filter first identifies the dominant dips inside an optimized processing window by a Fourier-radial transform in the frequency-wavenumber domain. The optimum size of the processing window depends on the intensity of random noise that needs to be attenuated and the amount of signal to be preserved. It then applies median filter along the dominant dip and retains the signals. Iterations are adopted to process the residual signals along the remaining dominant dips in a descending sequence, until all signals have been retained. The method is tested by both synthetic and field data gathers and also compared with the commonly used f-k least squares de-noising and f-x deconvolution.

Aftershocks of the western Argentina (Caucete) earthquake of 23 November 1977: some tectonic implications

USGS Publications Warehouse

Langer, C.J.; Bollinger, G.A.

1988-01-01

An aftershock survey, using a network of eight portable and two permanent seismographs, was conducted for the western Argentina (Caucete) earthquake (MS 7.3) of November 23, 1977. Monitoring began December 6, almost 2 weeks after the main shock and continued for 11 days. The data set includes 185 aftershock hypocenters that range in the depth from near surface to more than 30 km. The spatial distribution of those events occupied a volume of about 100 km long ??50 km wide ??30 km thick. The volumnar nature of the aftershock distribution is interpreted to be a result of a bimodal distribution of foci that define east- and west-dipping planar zones. Efforts to select which of those zones was associated with the causal faulting include special attention to the determination of the mainshock focal depth and dislocation theory modeling of the coseismic surface deformation in the epicentral region. Our focal depth (25-35 km) and modeling studies lead us to prefer an east-dipping plane as causal. A previous interpretation by other investigators used a shallower focal depth (17 km) and similar modeling calculations in choosing a west-dipping plane. Our selection of the east-dipping plane is physically more appealing because it places fault initiation at the base of the crustal seismogenic layer (rather than in the middle of that layer) which requires fault propagation to be updip (rather than downdip). ?? 1988.

Experimental and numerical study of hydraulic fracture geometry in shale formations with complex geologic conditions

NASA Astrophysics Data System (ADS)

Ma, Xinfang; Zhou, Tong; Zou, Yushi

2017-05-01

Strike-slip fault geostress and dipping laminated structures in Lujiaping shale formation typically result in difficultly predicting hydraulic fracture (HF) geometries. In this study, a novel 3D fracture propagation model based on discrete element method (DEM) is established. A series of simulations is performed to illustrate the influence of vertical stress difference (△σv = σv-σh), fluid viscosity, and injection rate, on HF growth geometry in the dipping layered formation. Results reveal that the fracturing fluid can easily infiltrate the dipping bedding plane (BP) interfaces with low net pressure for △σv = 1 MPa. HF height growth is also restricted. With increased △σv, fracture propagation in the vertical direction is enhanced, and a fracture network is formed by VF and partially opened dipping BPs. However, it is likely to create simple VF for △σv = 20 MPa. Appropriately increasing fracturing fluid viscosity and injection rate is conductive to weakening the containment effect of BPs on HF growth by increasing the fluid net pressure. However, no indication is found on whether a higher fracturing fluid viscosity is better. Higher viscosity can reduce the activation of BPs, so a stimulated reservoir volume is not necessarily increased. All these results can serve as theoretical guidance for the optimization of fracturing treatments in Lujiaping shale formation.

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers

PubMed Central

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-01-01

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work. PMID:28772954

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers.

PubMed

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-05-29

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

X-RAY SPECTROSCOPY OF THE HIGH-MASS X-RAY BINARY PULSAR CENTAURUS X-3 OVER ITS BINARY ORBIT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naik, Sachindra; Ali, Zulfikar; Paul, Biswajit, E-mail: snaik@prl.res.in

2011-08-20

We present a comprehensive spectral analysis of the high-mass X-ray binary (HMXB) pulsar Centaurus X-3 with the Suzaku observatory covering nearly one orbital period. The light curve shows the presence of extended dips which are rarely seen in HMXBs. These dips are seen up to as high as {approx}40 keV. The pulsar spectra during the eclipse, out-of-eclipse, and dips are found to be well described by a partial covering power-law model with high-energy cutoff and three Gaussian functions for 6.4 keV, 6.7 keV, and 6.97 keV iron emission lines. The dips in the light curve can be explained by themore » presence of an additional absorption component with high column density and covering fraction, the values of which are not significant during the rest of the orbital phases. The iron line parameters during the dips and eclipse are significantly different compared to those during the rest of the observation. During the dips, the iron line intensities are found to be lesser by a factor of 2-3 with a significant increase in the line equivalent widths. However, the continuum flux at the corresponding orbital phase is estimated to be lesser by more than an order of magnitude. Similarities in the changes in the iron line flux and equivalent widths during the dips and eclipse segments suggest that the dipping activity in Cen X-3 is caused by an obscuration of the neutron star by dense matter, probably structures in the outer region of the accretion disk, as in the case of dipping low-mass X-ray binaries.« less

Relationships of vascular function with measures of ambulatory blood pressure variation.

PubMed

Hodgson, Jonathan M; Woodman, Richard J; Croft, Kevin D; Ward, Natalie C; Bondonno, Catherine P; Puddey, Ian B; Lukoshkova, Elena V; Head, Geoffrey A

2014-03-01

Characteristics of short-term blood pressure (BP) variation may influence cardiovascular disease risk via effects on vascular function. In a cross-sectional study of a group of treated hypertensive and untreated largely normotensive subjects we investigated the relationships of measures of short-term BP variation with brachial artery vasodilator function. A total of 163 treated hypertensive (n = 91) and untreated largely normotensive (n = 72) men and women were recruited from the general population. Measures of systolic and diastolic BP variation were calculated from 24 h ambulatory BP assessments and included: (i) rate of measurement-to-measurement BP variation (SBP-var and DBP-var); and (ii) day-to-night BP dip (SBP-dip and DBP dip). Endothelium-dependent vasodilation was assessed as flow-mediated dilation (FMD) and endothelium-independent vasodilation was assessed in response to glyceryl trinitrate (GTN). Relationships were explored using univariate and multivariate linear regression. The relationships of brachial artery vasodilator function with BP variation were not significantly different between treated hypertensive and untreated subjects, therefore these groups were combined for analysis. In univariate analysis, higher SBP-var (P < 0.001) and lower DBP-dip (P = 0.004) were associated with lower FMD; and higher SBP-var (P = 0.002) and lower SBP-dip (P = 0.003) and DBP-dip (P = 0.001) were associated with lower GTN-mediated dilation. In multivariate analysis, lower SBP-dip (P = 0.007) and DBP-dip (P = 0.03) were independently associated with lower GTN response. Our results indicate that a lower day-to-night BP dip is independently associated with impaired smooth muscle cell function. Although rate of BP variation was associated with measures of endothelial and smooth muscle cell function, relationships were attenuated after accounting for age and BP. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Integrated stationary Ornstein-Uhlenbeck process, and double integral processes

NASA Astrophysics Data System (ADS)

Abundo, Mario; Pirozzi, Enrica

2018-03-01

We find a representation of the integral of the stationary Ornstein-Uhlenbeck (ISOU) process in terms of Brownian motion Bt; moreover, we show that, under certain conditions on the functions f and g , the double integral process (DIP) D(t) = ∫βt g(s) (∫αs f(u) dBu) ds can be thought as the integral of a suitable Gauss-Markov process. Some theoretical and application details are given, among them we provide a simulation formula based on that representation by which sample paths, probability densities and first passage times of the ISOU process are obtained; the first-passage times of the DIP are also studied.

First-order and subsidiary faults controlling the time-space evolution of the Central Italy 2016 seismic sequence - a multi-source data detailed 3D reconstruction

NASA Astrophysics Data System (ADS)

Lavecchia, Giusy; de nardis, Rita; Ferrarini, Federica; Cirillo, Daniele; Brozzetti, Francesco

2017-04-01

The Central Italy 2016 seismic sequence, with its three major events (24 August, Mw 6.0/6.2; 26 October Mw5.9/6.0; 30 October Mw6.5/6.6), activated a well-known active west-dipping extensional fault alignment of central Italy (Vettore-Gorzano faults, VEGO). Soon after the first event, based on geological, interferometric and at that moment available seismological data, a preliminary 3D fault model of VEGO was built. Such a model is here updated and improved at the light of a large amount of relocated earthquake data (time interval 24 August to 30 November 2016, 0.1≤ML ≤6.5, Chiaraluce at al., submitted to SRL) plus additional geological information. The 3D modeling was done using the software package MOVE from the Midland Valley. All the available data were taken into consideration (surface traces, fault-slip data, primary co-seismic surface fractures, geological maps and cross-sections, hypocentral locations and focal mechanisms of both background seismicity and seismic sequences). The VEGO geometric configuration did not substantially changed with respect to the previous model, but some additional structures involved in the sequence were reconstructed. In particular, four additional faults are well evident: a NE-dipping normal fault (dip-angle 50˚ ) antithetic to Vettore Fault, located at depths between 1 and 5 km; a WNW dipping plane (dip-angle 30˚ ) located at depth between 1 and 4 km within the Vettore footwall volume; this structure represents a splay of the late Miocene Sibillini thrust, which is evidently cross-cut and dislocated by the Vettore normal fault; a SW-dipping normal fault representing an unknown northward prosecution of the VEGO alignment, where since 26 October a relevant seismic activity was released; an unknown east-dipping low-angle detachment, where VEGO detaches at a depth of about 10-11 km. An uninterrupted microseismic activity has illuminated such a detachment not only during the overall sequence, but also in the previous months. At the light of the reconstructed geometric pattern integrated with the evidences of primary co-seismic fractures, it results evident that the Central Italy seismic sequence represents a "classic", although complex, intra-Apennine normal-faulting event, reactivating a long-term quiescent seismogenic alignment (e.g. VEGO). The reactivated and inverted compressional structures are confined at shallow depth within the Vettore footwall, and in no way control the major events of the sequence. Conversely, an important regional role is played by the east-dipping detachment. It represents the missing geometric link between the Altotiberina LANF of northern Umbria and the recently discovered LANF of Latium-Abruzzi.

Contribution of concentrator photovoltaic installations to grid stability and power quality

NASA Astrophysics Data System (ADS)

del Toro García, Xavier; Roncero-Sánchez, Pedro; Torres, Alfonso Parreño; Vázquez, Javier

2012-10-01

Large-scale integration of Photovoltaic (PV) generation systems, including Concentrator Photovoltaic (CPV) technologies, will require the contribution and support of these technologies to the management and stability of the grid. New regulations and grid codes for PV installations in countries such as Spain have recently included dynamic voltage control support during faults. The PV installation must stay connected to the grid during voltage dips and inject reactive power in order to enhance the stability of the system. The existing PV inverter technologies based on the Voltage-Source Converter (VSC) are in general well suited to provide advanced grid-support characteristics. Nevertheless, new advanced control schemes and monitoring techniques will be necessary to meet the most demanding requirements.

Continental growth by successive accretion of oceanic lithosphere: Evidence from tilted seismic anisotropy

NASA Astrophysics Data System (ADS)

Babuska, V.; Plomerova, J.; Karato, S. I.

2012-04-01

Although many studies indicate that subduction-related accretion, subduction-driven magmatism and tectonic stacking are major crustal-growth mechanisms, how the mantle lithosphere forms remains enigmatic. Cook (AGU Geod. Series 1986) published a model of continental 'shingling' based on seismic reflection data indicating dipping structures in the deep crust of accreted terranes. Helmstaedt and Gurney (J. Geoch. Explor. 1995) and Hart et al. (Geology 1997) suggest that the Archean continental lithosphere consists of alternating layers of basalt and peridotite derived from subducted and obducted Archean oceanic lithosphere. Peridotite xenoliths from the Mojavian mantle lithosphere (Luffi et al., JGR 2009), as well as xenoliths of eclogites underlying the Sierra Nevada batholith in California (Horodynskij et al., EPSL 2007), are representative for oceanic slab fragments successively attached to the continent. Recent seismological findings also seem to support a model of continental lithosphere built from systems of paleosubductions of plates of ancient oceanic lithosphere (Babuska and Plomerova, AGU Geoph. Monograph 1989), or by stacking of the plates (Helmstaedt and Schulze, Geol. Soc. Aust. Spec. Publ. 1989). Seismic anisotropy in the oceanic mantle lithosphere, explained mainly by the olivine A- (or D-) type fabric (Karato et al., Annu. Rev. Earth Planet. Sci. 2008), was discovered almost a half century ago (Hess, Nature 1964). Though it is difficult to determine seismic anisotropy within an active subducting slab (e.g., Healy et al., EPSL 2009; Eberhart-Phillips and Reyners, JGR 2009), field observations and laboratory experiments indicate the oceanic olivine fabric might be preserved there to a depth of at least 200-300 km. Dipping anisotropic fabrics in domains of the European mantle lithosphere were interpreted as systems of 'frozen' paleosubductions (Babuska and Plomerova, PEPI 2006), and the lithosphere base as a boundary between a fossil anisotropy in the lithospheric mantle and an underlying seismic anisotropy related to present-day flow in the asthenosphere (Plomerova and Babuska, Lithos 2010). Deep dipping reflectors in the Slave Craton were modelled as tops of a fossil oceanic lithosphere (Bostock, Lithos 1999). Using S-wave receiver functions, Miller and Eaton (GRL 2010) also interpreted mid-lithosphere discontinuities beneath British Columbia as remnant oceanic slabs. Strong radial anisotropy from global surface-wave data (Babuska et al., PAGEOPH 1998; Khan et al., JGR 2011), as well as differences between body-wave tomography images from SH and SV waves (Eken et al., Tectonophys. 2010), both showing strong anisotropy only down to ~200 km, are in agreement with the models of inclined olivine fabrics found in Phanerozoic and Precambrian mantle lithosphere (Plomerova et al., Solid Earth 2011). Models of assemblages of microplates with their own inclined fossil fabrics do not support a lithosphere growth by simple cooling processes, which should result in horizontal fabrics. The models with dipping fabrics also contribute to mapping boundaries of individual blocks building the continental lithosphere.

Restoration of the di-myo-inositol-phosphate pathway in the piezo-hyperthermophilic archaeon Thermococcus barophilus.

PubMed

Cario, Anaïs; Mizgier, Alex; Thiel, Axel; Jebbar, Mohamed; Oger, Phil M

2015-11-01

Most Thermococcales accumulate di-myo-inositol-phosphate (DIP) as an organic solute as a response to heat stress. We have studied the accumulation of this osmolyte in the high-hydrostatic pressure adapted hyperthermophile Thermococcus barophilus. We found no accumulation of DIP under any of the stress conditions tested, although this archaeon harbors the 3 DIP synthesis genes. Lack of synthesis is due to the lack of expression of TERMP_01135 coding for the second step of DIP synthesis. In contrast to other species, the T. barophilus synthesis operon is interrupted by a four gene locus, in reverse orientation. Restoring an operon like structure at the DIP locus restored DIP synthesis, but did not have an impact on growth characteristics, suggesting that other mechanisms have evolved in this organism to cope with heat stress. Copyright © 2015 Elsevier B.V. and Société Française de Biochimie et Biologie Moléculaire (SFBBM). All rights reserved.

Seismological constraints on the down-dip shape of normal faults

NASA Astrophysics Data System (ADS)

Reynolds, Kirsty; Copley, Alex

2018-04-01

We present a seismological technique for determining the down-dip shape of seismogenic normal faults. Synthetic models of non-planar source geometries reveal the important signals in teleseismic P and SH waveforms that are diagnostic of down-dip curvature. In particular, along-strike SH waveforms are the most sensitive to variations in source geometry, and have significantly more complex and larger-amplitude waveforms for curved source geometries than planar ones. We present the results of our forward-modelling technique for 13 earthquakes. Most continental normal-faulting earthquakes that rupture through the full seismogenic layer are planar and have dips of 30°-60°. There is evidence for faults with a listric shape from some of the earthquakes occurring in two regions; Tibet and East Africa. These ruptures occurred on antithetic faults, or minor faults within the hanging walls of the rifts affected, which may suggest a reason for the down-dip curvature. For these earthquakes, the change in dip across the seismogenic part of the fault plane is ≤30°.

Reflection coefficient of qP, qS and SH at a plane boundary between viscoelastic TTI media

NASA Astrophysics Data System (ADS)

Wang, Hongwei; Peng, Suping

2016-01-01

This paper introduces a calculation method for the effective elastic stiffness tensor matrix of the viscous-elastic TTI medium based on the Chapman theory. We then obtain the phase velocity formula and seismic wave polarization formula of the viscous-elastic TTI medium, by solving the Christoffel equation; solve the phase angle of reflection and transmission wave through the numerical method in accordance with the wave slowness ellipsoid; on the basis of this assumption, and assuming that qP, qS and SH waves occurred simultaneously at the viscous-elastic anisotropic interface, establish the sixth-order Zoeppritz equation in accordance with the boundary conditions; establish the models for the upper and lower media which are viscous-elastic HTI, TTI, etc., on the basis of the sixth-order Zoeppritz equation; and study the impact of fracture dip angle, azimuth angle and frequency on the reflection coefficient. From this we obtain the following conclusions: the reflection coefficient can identify the fracture strike and dip when any information pertaining to the media is unknown; dispersion phenomenon is obvious on the axial plane of symmetry and weakened in the plane vertical to the axial plane of symmetry; the vertical-incidence longitudinal wave can stimulate the qS wave when the dip angle is not 0° or 90° under the condition of coincidence between the symmetry planes of the upper and lower media; when the symmetry planes of the upper and lower media do not coincide and the dip angle is not 0° or 90°, then the vertical-incidence qP will stimulate the qS and SH waves at the same time; the dip angle can cause the reflection coefficient curve to have a more obvious dispersion phenomenon, while the included angle between the symmetry planes of the upper and lower media will weaken the dispersion except SH; and the intercept of reflection coefficient is affected by the fracture dip and included angle between the symmetry planes of the upper and lower media.

Nanoscale surface analysis on second generation advanced high strength steel after hot dip galvanizing.

PubMed

Arndt, M; Duchoslav, J; Preis, K; Samek, L; Stifter, D

2013-09-01

Second generation advanced high strength steel is one promising material of choice for modern automotive structural parts because of its outstanding maximal elongation and tensile strength. Nonetheless there is still a lack of corrosion protection for this material due to the fact that cost efficient hot dip galvanizing cannot be applied. The reason for the insufficient coatability with zinc is found in the segregation of manganese to the surface during annealing and the formation of manganese oxides prior coating. This work analyses the structure and chemical composition of the surface oxides on so called nano-TWIP (twinning induced plasticity) steel on the nanoscopic scale after hot dip galvanizing in a simulator with employed analytical methods comprising scanning Auger electron spectroscopy (SAES), energy dispersive X-ray spectroscopy (EDX), and focused ion beam (FIB) for cross section preparation. By the combination of these methods, it was possible to obtain detailed chemical images serving a better understanding which processes exactly occur on the surface of this novel kind of steel and how to promote in the future for this material system galvanic protection.

Adsorption detection for polylysine biomolecules based on high-Q silica capillary whispering gallery mode microresonator

NASA Astrophysics Data System (ADS)

Wu, Jixuan; Liu, Bo; Zhang, Hao; Song, Binbin

2017-11-01

A silica-capillary-based whispering gallery mode (WGM) microresonator has been proposed and experimentally demonstrated for the real-time monitoring of the polylysine adsorption process. The spectral characteristics of the WGM resonance dips with high quality factor and good wavelength selectivity have been investigated to evaluate the dynamic process for the binding of polylysine with a capillary surface. The WGM transmission spectrum shows a regular shift with increments of observation time, which could be exploited for the analysis of the polylysine adsorption process. The proposed WGM microresonator system possesses desirable qualities such as high sensitivity, fast response, label-free method, high detection resolution and compactness, which could find promising applications in histology and related bioengineering areas.

Accurate Orientation Estimation Using AHRS under Conditions of Magnetic Distortion

PubMed Central

Yadav, Nagesh; Bleakley, Chris

2014-01-01

Low cost, compact attitude heading reference systems (AHRS) are now being used to track human body movements in indoor environments by estimation of the 3D orientation of body segments. In many of these systems, heading estimation is achieved by monitoring the strength of the Earth's magnetic field. However, the Earth's magnetic field can be locally distorted due to the proximity of ferrous and/or magnetic objects. Herein, we propose a novel method for accurate 3D orientation estimation using an AHRS, comprised of an accelerometer, gyroscope and magnetometer, under conditions of magnetic field distortion. The system performs online detection and compensation for magnetic disturbances, due to, for example, the presence of ferrous objects. The magnetic distortions are detected by exploiting variations in magnetic dip angle, relative to the gravity vector, and in magnetic strength. We investigate and show the advantages of using both magnetic strength and magnetic dip angle for detecting the presence of magnetic distortions. The correction method is based on a particle filter, which performs the correction using an adaptive cost function and by adapting the variance during particle resampling, so as to place more emphasis on the results of dead reckoning of the gyroscope measurements and less on the magnetometer readings. The proposed method was tested in an indoor environment in the presence of various magnetic distortions and under various accelerations (up to 3 g). In the experiments, the proposed algorithm achieves <2° static peak-to-peak error and <5° dynamic peak-to-peak error, significantly outperforming previous methods. PMID:25347584

More Unusual Light Curves from Kepler

NASA Astrophysics Data System (ADS)

Kohler, Susanna

2017-03-01

Twenty-three new objects have been added to the growing collection of stars observed to have unusual dips in their light curves. A recent study examines these stars and the potential causes of their strange behavior.An Influx of DataThe primary Kepler mission provided light curves for over 100,000 stars, and its continuation K2 is observing another 20,000 stars every three months. As we enter an era where these enormous photometric data sets become commonplace Gaia will obtain photometry for millions of stars, and LSST billions its crucial that we understand the different categories of variability observed in these stars.The authors find three different types of light curves among their 23 unusual stars. Scallop-shell curves (top) show many undulations; persistent flux-dip class curves (middle) have discrete triangularly shaped flux dips; transient, narrow dip class curves (bottom) have only one dip that is variable in depth. The authors speculate a common cause for the scallop-shell and persistent flux-dip stars, and a different cause for the transient flux-dip stars. [Stauffer et al. 2017]After filtering out the stars with planets, those in binary systems, those with circumstellar disks, and those with starspots, a number of oddities remain: a menagerie of stars with periodic variability that cant be accounted for in these categories. Some of these stars are now famous (for instance, Boyajians star); some are lesser known. But by continuing to build up this sample of stars with unusual light curves, we have a better chance of understanding the sources of variability.Building the MenagerieTo this end, a team of scientists led by John Stauffer (Spitzer Science Center at Caltech) has recently hunted for more additions to this sample in the K2 data set. In particular, they searched through the light curves from stars in the Oph and Upper Scorpius star-forming region a data set that makes up the largest collection of high-quality light curves for low-mass, pre-main-sequence stars ever obtained.In these light curves, Stauffer and collaborators found a set of 23 very low-mass, mid-to-late-type M dwarfs with unusual variability in their light curves. The variability is consistent with the stars rotation period where measured which suggests that whatever causes the dips in the light curve, its orbiting at the same rate as the star spins.Causes of Variability?These plots show how the properties of these 23 stars compare to those of the rest of the stars in their cluster (click for a closer look!). For all but the rotation rate, they are typical. But the stars with scallop-shaped light curves have among the shortest periods in Upper Sco, with somenear the theoretical break-up for stars of their age. [Stauffer et al. 2017]The authors categorize the 23 stars into two main groups.The first group consists of 19 stars with short periods; more than half of them rotate within a factor of two of their predicted breakup period! Many of these show sudden changes in their light-curve morphology, often after a stellar flare. The authors propose that the variability in these light curves might be caused by warm coronal gas clouds that are organized into a structured toroidal shape around the star.The second group consists of the remaining four stars, which have slightly longer periods. The light curves show a single short-duration flux dip with highly variable depth and shape superposed on normal, spotted-star light curves. The authors best guess for these four stars is that there are clouds of dusty debris circling the star, possibly orbiting a close-in planet or resulting from a recent collisional event.Stauffer and collaborators are currently developing more detailed models for these stars based on the possible variability scenarios. The next step, they state, is to determine if the gas in these structures have properties necessary to generate the light-curve features we see.CitationJohn Stauffer et al 2017 AJ 153 152. doi:10.3847/1538-3881/aa5eb9

Quantitative geometric description of fracture systems in an andesite lava flow using terrestrial laser scanner data

NASA Astrophysics Data System (ADS)

Massiot, Cécile; Nicol, Andrew; Townend, John; McNamara, David D.; Garcia-Sellés, David; Conway, Chris E.; Archibald, Garth

2017-07-01

Permeability hosted in andesitic lava flows is dominantly controlled by fracture systems, with geometries that are often poorly constrained. This paper explores the fracture system geometry of an andesitic lava flow formed during its emplacement and cooling over gentle paleo-topography, on the active Ruapehu volcano, New Zealand. The fracture system comprises column-forming and platy fractures within the blocky interior of the lava flow, bounded by autobreccias partially observed at the base and top of the outcrop. We use a terrestrial laser scanner (TLS) dataset to extract column-forming fractures directly from the point-cloud shape over an outcrop area of ∼3090 m2. Fracture processing is validated using manual scanlines and high-resolution panoramic photographs. Column-forming fractures are either steeply or gently dipping with no preferred strike orientation. Geometric analysis of fractures derived from the TLS, in combination with virtual scanlines and trace maps, reveals that: (1) steeply dipping column-forming fracture lengths follow a scale-dependent exponential or log-normal distribution rather than a scale-independent power-law; (2) fracture intensities (combining density and size) vary throughout the blocky zone but have similar mean values up and along the lava flow; and (3) the areal fracture intensity is higher in the autobreccia than in the blocky zone. The inter-connected fracture network has a connected porosity of ∼0.5 % that promote fluid flow vertically and laterally within the blocky zone, and is partially connected to the autobreccias. Autobreccias may act either as lateral permeability connections or barriers in reservoirs, depending on burial and alteration history. A discrete fracture network model generated from these geometrical parameters yields a highly connected fracture network, consistent with outcrop observations.

Images for the base of the Pacific lithospheric plate beneath Wellington, New Zealand, from 500 kg dynamite shots recorded on a 100 km-long, 1000 seismometer array

NASA Astrophysics Data System (ADS)

Stern, T. A.; Henrys, S. A.; Sato, H.; Okaya, D. A.

2012-12-01

Seismic P and S-wave reflections are recorded from a west-dipping horizon at depth of 105 km beneath Wellington, New Zealand. From the depth and dip of this horizon we interpret this horizon to be the bottom of the subducting Pacific plate. In May 2011 the Seismic Array on Hikurangi margin Experiment (SAHKE) recorded reflections on a ~100 km-long high-resolution seismic line across the lower North Island of New Zealand. The main goal of this experiment was to provide a detailed image of the west dipping subducted Pacific plate beneath the Wellington city region. The seismic line had ~1000 seismographs spaced between 50-100 m apart and the 500 kg shots were in 50 m-deep, drill holes. An exceptionally high-resolution image for the top of the subducting Pacific Plate at a depth of 20-25 km beneath the Wellington region is seen. In addition, on most of the shots are a pair of 10-14 Hz reflections between 27 and 29 s two-way-travel-time (twtt) at zero offset. The quality of this reflection pair varies from shot to shot. When converted to depth and ray-traced the best solution for these deep events is a west-dipping ( ~ 15 degrees) horizon at a depth of about 105 km. This is consistent with the dip of the upper surface of the plate beneath Wellington, and therefore we argue that the deep (~105 km) reflector is the base of the Pacific plate. On two of the shots another pair 5-8 Hz reflections can also be seen between 47 and 52 s, and the move-out of these events is consistent with them being S-wave reflections from the same 105 km deep, west-dipping, boundary for a Vp/Vs ~ 1.74. Both the P-and S-wave reflections occur in pairs of twtt-thickness of 2 and 5 s, respectively and appear to define a ~ 6-8 km thick channel at the base of the plate if the Vp/Vs ratio~ 5/2 or 2.5. Such a high value of Vp/Vs is consistent with the channel containing fluids or partial melt of an unknown percent. Although we can't rule out the double reflections in both P and S as being multiples, this seems unlikely as multiples are not seen any where else in the shot gathers. Thus the lithosphere-asthenosphere boundary (LAB), at least in this setting, appears to be a sharp boundary, less than 10 km thick. As the top of the subduction zone is 20-25 km deep beneath our profile, the total thickness of the plate beneath Wellington is about 80 km. This is consistent with the thickness of old oceanic plates measured elsewhere with passive seismic methods.

Design and properties of a cryogenic dip-stick scanning tunneling microscope with capacitive coarse approach control.

PubMed

Schlegel, R; Hänke, T; Baumann, D; Kaiser, M; Nag, P K; Voigtländer, R; Lindackers, D; Büchner, B; Hess, C

2014-01-01

We present the design, setup, and operation of a new dip-stick scanning tunneling microscope. Its special design allows measurements in the temperature range from 4.7 K up to room temperature, where cryogenic vacuum conditions are maintained during the measurement. The system fits into every (4)He vessel with a bore of 50 mm, e.g., a transport dewar or a magnet bath cryostat. The microscope is equipped with a cleaving mechanism for cleaving single crystals in the whole temperature range and under cryogenic vacuum conditions. For the tip approach, a capacitive automated coarse approach is implemented. We present test measurements on the charge density wave system 2H-NbSe2 and the superconductor LiFeAs which demonstrate scanning tunneling microscopy and spectroscopy data acquisition with high stability, high spatial resolution at variable temperatures and in high magnetic fields.

75 FR 52789 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-27

... for Woven and Knit impregnated with Flat Dipped Rubber/Plastic Gloves. SUMMARY: The U.S. Small... for woven and knit impregnated with flat dipped rubber/plastic gloves, under the North American... Dipped Rubber/Plastic Gloves manufacturers. If granted, the waiver would allow otherwise qualified small...

Gently dipping normal faults identified with Space Shuttle radar topography data in central Sulawesi, Indonesia, and some implications for fault mechanics

USGS Publications Warehouse

Spencer, J.E.

2011-01-01

Space-shuttle radar topography data from central Sulawesi, Indonesia, reveal two corrugated, domal landforms, covering hundreds to thousands of square kilometers, that are bounded to the north by an abrupt transition to typical hilly to mountainous topography. These domal landforms are readily interpreted as metamorphic core complexes, an interpretation consistent with a single previous field study, and the abrupt northward transition in topographic style is interpreted as marking the trace of two extensional detachment faults that are active or were recently active. Fault dip, as determined by the slope of exhumed fault footwalls, ranges from 4?? to 18??. Application of critical-taper theory to fault dip and hanging-wall surface slope, and to similar data from several other active or recently active core complexes, suggests a theoretical limit of three degrees for detachment-fault dip. This result appears to conflict with the dearth of seismological evidence for slip on faults dipping less than ~. 30??. The convex-upward form of the gently dipping fault footwalls, however, allows for greater fault dip at depths of earthquake initiation and dominant energy release. Thus, there may be no conflict between seismological and mapping studies for this class of faults. ?? 2011 Elsevier B.V.

Possible Strain Partitioning Between the Kumano Forearc Basin and the Slope of the Nankai Trough Accretionary Prism

NASA Astrophysics Data System (ADS)

Martin, K. M.; Gulick, S. P.; Bangs, N. L.; Ashi, J.; Moore, G. F.; Nakamura, Y.; Tobin, H. J.

2008-12-01

A 12 km wide, 56 km long, three-dimensional (3-D) seismic volume acquired over the Nankai Trough offshore the Kii Peninsula, Japan images the Nankai accretionary prism, forearc basin and the subducting Philippine Sea Plate. We have analyzed an unusual, trench-parallel ~1200 m deep depression (a "notch") along the seaward edge of the Kumano forearc basin, just landward of the shallowest branch of the previously- mapped splay-fault system. The shape of this feature varies along strike, from a single, steep-walled, ~3.5 km wide notch in the northeast, to a broader, ~6 km wide zone with several shallower linear bathymetric lows in the southwest. We have mapped the area below the notch and found both vertical faults and faults which dip toward the central axis of the depression. Some dipping faults appear to have normal offset, consistent with the formation of a bathymetric low. Some of these dipping faults may join the central vertical fault(s) at depth, creating apparent flower structures. Offset on the vertical faults is more difficult to determine, but the dip and along-strike geometry of these faults makes predominantly normal or thrust motion unlikely. We conclude, therefore, that the notch feature is the bathymetric expression of a transtensional fault system. Possible causes for such a system in the forearc include variations in splay fault geometry and strain partitioning. By considering only the along-strike variability of the mapped splay fault, we were unable to explain a transform feature at the scale of the notch. Strike-slip faulting at the seaward edge of forearc basins is also observed in Sumatra and is there attributed to strain partitioning due to oblique convergence. The wedge and décollment strength variations which control the location of the forearc basins may therefore play a role in the position where the along-strike component of deformation is localized. While the obliquity of convergence in the Nankai trough is comparatively small (13-30 degrees), we believe it is still significant enough to account for the formation of the observed notch.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Townsend, M., Prothro, L. B., Obi, C.

A test bed for a series of chemical explosives tests known as Source Physics Experiments (SPE) was constructed in granitic rock of the Climax stock, in northern Yucca Flat at the Nevada National Security Site in 2010-2011. These tests are sponsored by the U.S. Department of Energy, National Nuclear Security Administration's National Center for Nuclear Security. The test series is designed to study the generation and propagation of seismic waves, and will provide data that will improve the predictive capability of calculational models for detecting and characterizing underground explosions. Abundant geologic data are available for the area, primarily as amore » result of studies performed in conjunction with the three underground nuclear tests conducted in the Climax granite in the 1960s and a few later studies of various types. The SPE test bed was constructed at an elevation of approximately 1,524 meters (m), and consists of a 91.4-centimeter (cm) diameter source hole at its center, surrounded by two rings of three 20.3-cm diameter instrument holes. The inner ring of holes is positioned 10 m away from the source hole, and the outer ring of holes is positioned 20 m from the source hole. An initial 160-m deep core hole was drilled at the location of the source hole that provided information on the geology of the site and rock samples for later laboratory testing. A suite of geophysical logs was run in the core hole and all six instruments holes to obtain matrix and fracture properties. Detailed information on the character and density of fractures encountered was obtained from the borehole image logs run in the holes. A total of 2,488 fractures were identified in the seven boreholes, and these were ranked into six categories (0 through 5) on the basis of their degree of openness and continuity. The analysis presented here considered only the higher-ranked fractures (ranks 2 through 5), of which there were 1,215 (approximately 49 percent of all fractures identified from borehole image logs). The fractures were grouped into sets based on their orientation. The most ubiquitous fracture set (50 percent of all higher-ranked fractures) is a group of low-angle fractures (dips 0 to 30 degrees). Fractures with dips of 60 to 90 degrees account for 38 percent of high-ranked fractures, and the remaining 12 percent are fractures with moderate dips (30 to 60 degrees). The higher-angle fractures are further subdivided into three sets based on their dip direction: fractures of Set 1 dip to the north-northeast, fractures of Set 2 dip to the south-southwest, and Set 3 consists of high-angle fractures that dip to the southeast and strike northeast. The low-angle fractures (Set 4) dip eastward. Fracture frequency does not appear to change substantially with depth. True fracture spacing averages 0.9 to 1.2 m for high-angle Sets 1, 2, and 3, and 0.6 m for Set 4. Two significant faults were observed in the core, centered at the depths of 25.3 and 32.3 m. The upper of these two faults dips 80 degrees to the north-northeast and, thus, is related to the Set-1 fractures. The lower fault dips 79 degrees to the south-southwest and is related to SPE Set-2 fractures. Neither fault has an identifiable surface trace. Groundwater was encountered in all holes drilled on the SPE test bed, and the fluid level averaged about 15.2 to 18.3 m below ground surface. An informal study of variations in the fluid level in the holes conducted during various phases of construction of the test bed concluded that groundwater flow through the fractured granitic rocks is not uniform, and appears to be controlled by variations in the orientation and degree of interconnectedness of the fractures. It may also be possible that an aplite dike or quartz vein may be present in the test bed, which could act as a barrier to groundwater flow and, thus, could account for anisotropy seen in the groundwater recovery measurements.« less

Applying the miniaturization technologies for biosensor design.

PubMed

Derkus, Burak

2016-05-15

Microengineering technologies give us some opportunities in developing high-tech sensing systems that operate with low volumes of samples, integrates one or more laboratory functions on a single substrate, and enables automation. These millimetric sized devices can be produced for only a few dollars, which makes them promising candidates for mass-production. Besides electron beam lithography, stencil lithography, nano-imprint lithography or dip pen lithography, basic photolithography is the technique which is extensively used for the design of microengineered sensing systems. This technique has some advantages such as easy-to-manufacture, do not require expensive instrumentation, and allow creation of lower micron-sized patterns. In this review, it has been focused on three different type of microengineered sensing devices which are developed using micro/nano-patterning techniques, microfluidic technology, and microelectromechanics system based technology. Copyright © 2016 Elsevier B.V. All rights reserved.

Health Plans and Drug Companies Dip Their Toes Into Value-Based Pricing: The Pressure Is on P&T Committees to Monitor Utilization.

PubMed

Barlas, Stephen

2016-01-01

The agreement between Harvard Pilgrim and Amgen on a "pay for performance" deal involving evolocumab could encourage other manufacturers, health plans, and policy-makers to press for value-based pricing as drug costs continue to escalate.

DipTest: A litmus test for E. coli detection in water.

PubMed

Gunda, Naga Siva Kumar; Dasgupta, Saumyadeb; Mitra, Sushanta K

2017-01-01

We have developed a new litmus paper test (DipTest) for detecting Escherichia coli (E. coli) in water samples by performing enzymatic reactions directly on the porous paper substrate. The paper strip consists of a long narrow piece of cellulose blotting paper coated with chemoattractant (at bottom edge), wax hydrophobic barrier (at the top edge), and custom formulated chemical reagents (at reaction zone immediately below the wax hydrophobic barrier). When the paper strip is dipped in water, E. coli in the water sample is attracted toward the paper strip due to a chemotaxic mechanism followed by the ascent along the paper strip toward the reaction zone due to a capillary wicking mechanism, and finally the capillary motion is arrested at the top edge of the paper strip by the hydrophobic barrier. The E. coli concentrated at the reaction zone of the paper strip will react with custom formulated chemical reagents to produce a pinkish-red color. Such a color change on the paper strip when dipped into water samples indicates the presence of E. coli contamination in potable water. The performance of the DipTest device has been checked with different known concentrations of E. coli contaminated water samples using different dip and wait times. The DipTest device has also been tested with different interfering bacteria and chemical contaminants. It has been observed that the different interfering contaminants do not have any impact on the DipTest, and it can become a potential solution for screening water samples for E. coli contamination at the point of source.

DipTest: A litmus test for E. coli detection in water

PubMed Central

Gunda, Naga Siva Kumar; Dasgupta, Saumyadeb

2017-01-01

We have developed a new litmus paper test (DipTest) for detecting Escherichia coli (E. coli) in water samples by performing enzymatic reactions directly on the porous paper substrate. The paper strip consists of a long narrow piece of cellulose blotting paper coated with chemoattractant (at bottom edge), wax hydrophobic barrier (at the top edge), and custom formulated chemical reagents (at reaction zone immediately below the wax hydrophobic barrier). When the paper strip is dipped in water, E. coli in the water sample is attracted toward the paper strip due to a chemotaxic mechanism followed by the ascent along the paper strip toward the reaction zone due to a capillary wicking mechanism, and finally the capillary motion is arrested at the top edge of the paper strip by the hydrophobic barrier. The E. coli concentrated at the reaction zone of the paper strip will react with custom formulated chemical reagents to produce a pinkish-red color. Such a color change on the paper strip when dipped into water samples indicates the presence of E. coli contamination in potable water. The performance of the DipTest device has been checked with different known concentrations of E. coli contaminated water samples using different dip and wait times. The DipTest device has also been tested with different interfering bacteria and chemical contaminants. It has been observed that the different interfering contaminants do not have any impact on the DipTest, and it can become a potential solution for screening water samples for E. coli contamination at the point of source. PMID:28877199

Thin-skinned tectonics of upper Ojai Valley and Sulfur Mountain vicinity, Ventura basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huftile, G.J.

1988-03-01

The Upper Ojai Valley is a tectonic depression between opposing reverse faults. The active, north-dipping San Cayetano fault forms its northern border and has 5.8 km of dip-slip displacement at the Silverthread oil field and 2.6 km of displacement west of Sisar Creek. The fault dies out farther west in Ojai Valley. The southern border is formed by the late Quaternary Sisar-Big-Canyon-Lion fault set, which dips south and merges into a decollement within the south-dipping, ductile Rincon Formation. Folds with north-dipping fold axes, including the Lion Mountain anticline and Reeves syncline, are probably Pliocene. During the late Quaternary, the Sulfurmore » Mountain anticlinorium began forming as a fault-propagation fold, followed closely by the ramping of the south-dipping faults to the surface. One, the Lion fault, cuts the Pleistocene Saugus Formation. To the east, the San Cayetano fault overrides and folds the south-dipping faults. Cross-section balancing shows that the Miocene and younger rocks above the decollement are shortened 6.1 km more than the more competent rocks below. A solution to this bed-length problem is that the decollement becomes a ramp and merges at depth with the steeply south-dipping Oak Ridge fault. This implies that the Sisar, Big Canyon, and Lion faults are frontal thrusts to the Oak Ridge fault. Oil is produced primarily from Mohnian sands and shales north of the Big Canyon fault and from fractured Mohnian shale beneath the Sisar fault.« less

Floral-Dip Transformation of Flax (Linum usitatissimum) to Generate Transgenic Progenies with a High Transformation Rate

PubMed Central

Bastaki, Nasmah K.; Cullis, Christopher A.

2014-01-01

Agrobacterium-mediated plant transformation via floral-dip is a widely used technique in the field of plant transformation and has been reported to be successful for many plant species. However, flax (Linum usitatissimum) transformation by floral-dip has not been reported. The goal of this protocol is to establish that Agrobacterium and the floral-dip method can be used to generate transgenic flax. We show that this technique is simple, inexpensive, efficient, and more importantly, gives a higher transformation rate than the current available methods of flax transformation. In summary, inflorescences of flax were dipped in a solution of Agrobacterium carrying a binary vector plasmid (T-DNA fragment plus the Linum Insertion Sequence, LIS-1) for 1 - 2 min. The plants were laid flat on their side for 24 hr. Then, plants were maintained under normal growth conditions until the next treatment. The process of dipping was repeated 2 - 3 times, with approximately 10 - 14 day intervals between dipping. The T1 seeds were collected and germinated on soil. After approximately two weeks, treated progenies were tested by direct PCR; 2 - 3 leaves were used per plant plus the appropriate T-DNA primers. Positive transformants were selected and grown to maturity. The transformation rate was unexpectedly high, with 50 - 60% of the seeds from treated plants being positive transformants. This is a higher transformation rate than those reported for Arabidopsis thaliana and other plant species, using floral-dip transformation. It is also the highest, which has been reported so far, for flax transformation using other methods for transformation. PMID:25549243

Floral-dip transformation of flax (Linum usitatissimum) to generate transgenic progenies with a high transformation rate.

PubMed

Bastaki, Nasmah K; Cullis, Christopher A

2014-12-19

Agrobacterium-mediated plant transformation via floral-dip is a widely used technique in the field of plant transformation and has been reported to be successful for many plant species. However, flax (Linum usitatissimum) transformation by floral-dip has not been reported. The goal of this protocol is to establish that Agrobacterium and the floral-dip method can be used to generate transgenic flax. We show that this technique is simple, inexpensive, efficient, and more importantly, gives a higher transformation rate than the current available methods of flax transformation. In summary, inflorescences of flax were dipped in a solution of Agrobacterium carrying a binary vector plasmid (T-DNA fragment plus the Linum Insertion Sequence, LIS-1) for 1 - 2 min. The plants were laid flat on their side for 24 hr. Then, plants were maintained under normal growth conditions until the next treatment. The process of dipping was repeated 2 - 3 times, with approximately 10 - 14 day intervals between dipping. The T1 seeds were collected and germinated on soil. After approximately two weeks, treated progenies were tested by direct PCR; 2 - 3 leaves were used per plant plus the appropriate T-DNA primers. Positive transformants were selected and grown to maturity. The transformation rate was unexpectedly high, with 50 - 60% of the seeds from treated plants being positive transformants. This is a higher transformation rate than those reported for Arabidopsis thaliana and other plant species, using floral-dip transformation. It is also the highest, which has been reported so far, for flax transformation using other methods for transformation.

Aligned silver nanowire-based transparent electrodes for engineering polarisation-selective optoelectronics.

PubMed

Park, Byoungchoo; Bae, In-Gon; Huh, Yoon Ho

2016-01-18

We herein report on a remarkably simple, fast, and economic way of fabricating homogeneous and well oriented silver nanowires (AgNWs) that exhibit strong in-plane electrical and optical anisotropies. Using a small quantity of AgNW suspension, the horizontal-dip (H-dip) coating method was applied, in which highly oriented AgNWs were deposited unidirectionally along the direction of coating over centimetre-scale lengths very rapidly. In applying the H-dip-coating method, we adjusted the shear strain rate of the capillary flow in the Landau-Levich meniscus of the AgNW suspension, which induced a high degree of uniaxial orientational ordering (0.37-0.43) of the AgNWs, comparable with the ordering seen in archetypal nematic liquid crystal (LC) materials. These AgNWs could be used to fabricate not only transparent electrodes, but also LC-alignment electrodes for LC devices and/or polarising electrodes for organic photovoltaic devices, having the potential to revolutionise the architectures of a number of polarisation-selective opto-electronic devices for use in printed/organic electronics.

Slip in the 2015 Mw 7.9 Gorkha and Mw 7.3 Kodari, Nepal, earthquakes revealed by seismic and geodetic data: Delayed slip in the Gorkha and slip deficit between the two earthquakes

NASA Astrophysics Data System (ADS)

Zhang, G.; Hetland, E.; Shan, X.

2017-12-01

We investigate the rupture process of the April 25, 2015 Gorkha, Nepal Mw7.9 earthquake, and its biggest aftershock on May 12, 2015, based on joint inversion of teleseismic body waves, InSAR and GPS measurements. The Gorkha earthquake propagated unilaterally to the southeast along the MFT, with coseismic slip separating into patches up-dip and down-dip of the hypocenter. Slip in the up-dip patch initially surrounded a region on the fault that did not slip. About 15 seconds after being surrounded, this region of no slip then slipped, filling in the slip deficit. The delayed slip accounts for about 20% of the moment release in the Gorkha earthquake. The inferred coseismic slip in the Kodari earthquake is localized to one patch, extending to the south and southeast from the hypocenter, and 20-30 km to the northeast of the main slip patch in the Ghorka earthquake. The maximum coseismic slip in both the Gorkha and Kodari earthquakes is about 4.5 meters.

Solar Filament Longitudinal Oscillations along a Magnetic Field Tube with Two Dips

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou Yu-Hao; Zhang Li-Yue; Ouyang, Y.

Large-amplitude longitudinal oscillations of solar filaments have been observed and explored for more than ten years. Previous studies are mainly based on the one-dimensional rigid flux tube model with a single magnetic dip. However, it has been noted that there might be two magnetic dips, and hence two threads, along one magnetic field line. Following previous work, we intend to investigate the kinematics of the filament longitudinal oscillations when two threads are magnetically connected, which is done by solving one-dimensional radiative hydrodynamic equations with the numerical code MPI-AMRVAC. Two different types of perturbations are considered, and the difference from previousmore » works resulting from the interaction of the two filament threads is investigated. We find that even with the inclusion of the thread–thread interaction, the oscillation period is modified weakly, by at most 20% compared to the traditional pendulum model with one thread. However, the damping timescale is significantly affected by the thread–thread interaction. Hence, we should take it into account when applying the consistent seismology to the filaments where two threads are magnetically connected.« less

Protein Sub-Nuclear Localization Based on Effective Fusion Representations and Dimension Reduction Algorithm LDA.

PubMed

Wang, Shunfang; Liu, Shuhui

2015-12-19

An effective representation of a protein sequence plays a crucial role in protein sub-nuclear localization. The existing representations, such as dipeptide composition (DipC), pseudo-amino acid composition (PseAAC) and position specific scoring matrix (PSSM), are insufficient to represent protein sequence due to their single perspectives. Thus, this paper proposes two fusion feature representations of DipPSSM and PseAAPSSM to integrate PSSM with DipC and PseAAC, respectively. When constructing each fusion representation, we introduce the balance factors to value the importance of its components. The optimal values of the balance factors are sought by genetic algorithm. Due to the high dimensionality of the proposed representations, linear discriminant analysis (LDA) is used to find its important low dimensional structure, which is essential for classification and location prediction. The numerical experiments on two public datasets with KNN classifier and cross-validation tests showed that in terms of the common indexes of sensitivity, specificity, accuracy and MCC, the proposed fusing representations outperform the traditional representations in protein sub-nuclear localization, and the representation treated by LDA outperforms the untreated one.

Geoelectric Characterization of Thermal Water Aquifers Using 2.5D Inversion of VES Measurements

NASA Astrophysics Data System (ADS)

Gyulai, Á.; Szűcs, P.; Turai, E.; Baracza, M. K.; Fejes, Z.

2017-03-01

This paper presents a short theoretical summary of the series expansion-based 2.5D combined geoelectric weighted inversion (CGWI) method and highlights the advantageous way with which the number of unknowns can be decreased due to the simultaneous characteristic of this inversion. 2.5D CGWI is an approximate inversion method for the determination of 3D structures, which uses the joint 2D forward modeling of dip and strike direction data. In the inversion procedure, the Steiner's most frequent value method is applied to the automatic separation of dip and strike direction data and outliers. The workflow of inversion and its practical application are presented in the study. For conventional vertical electrical sounding (VES) measurements, this method can determine the parameters of complex structures more accurately than the single inversion method. Field data show that the 2.5D CGWI which was developed can determine the optimal location for drilling an exploratory thermal water prospecting well. The novelty of this research is that the measured VES data in dip and strike direction are jointly inverted by the 2.5D CGWI method.

Scalable, "Dip-and-Dry" Fabrication of a Wide-Angle Plasmonic Selective Absorber for High-Efficiency Solar-Thermal Energy Conversion.

PubMed

Mandal, Jyotirmoy; Wang, Derek; Overvig, Adam C; Shi, Norman N; Paley, Daniel; Zangiabadi, Amirali; Cheng, Qian; Barmak, Katayun; Yu, Nanfang; Yang, Yuan

2017-11-01

A galvanic-displacement-reaction-based, room-temperature "dip-and-dry" technique is demonstrated for fabricating selectively solar-absorbing plasmonic-nanoparticle-coated foils (PNFs). The technique, which allows for facile tuning of the PNFs' spectral reflectance to suit different radiative and thermal environments, yields PNFs which exhibit excellent, wide-angle solar absorptance (0.96 at 15°, to 0.97 at 35°, to 0.79 at 80°), and low hemispherical thermal emittance (0.10) without the aid of antireflection coatings. The thermal emittance is on par with those of notable selective solar absorbers (SSAs) in the literature, while the wide-angle solar absorptance surpasses those of previously reported SSAs with comparable optical selectivities. In addition, the PNFs show promising mechanical and thermal stabilities at temperatures of up to 200 °C. Along with the performance of the PNFs, the simplicity, inexpensiveness, and environmental friendliness of the "dip-and-dry" technique makes it an appealing alternative to current methods for fabricating selective solar absorbers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Protein Sub-Nuclear Localization Based on Effective Fusion Representations and Dimension Reduction Algorithm LDA

PubMed Central

Wang, Shunfang; Liu, Shuhui

2015-01-01

An effective representation of a protein sequence plays a crucial role in protein sub-nuclear localization. The existing representations, such as dipeptide composition (DipC), pseudo-amino acid composition (PseAAC) and position specific scoring matrix (PSSM), are insufficient to represent protein sequence due to their single perspectives. Thus, this paper proposes two fusion feature representations of DipPSSM and PseAAPSSM to integrate PSSM with DipC and PseAAC, respectively. When constructing each fusion representation, we introduce the balance factors to value the importance of its components. The optimal values of the balance factors are sought by genetic algorithm. Due to the high dimensionality of the proposed representations, linear discriminant analysis (LDA) is used to find its important low dimensional structure, which is essential for classification and location prediction. The numerical experiments on two public datasets with KNN classifier and cross-validation tests showed that in terms of the common indexes of sensitivity, specificity, accuracy and MCC, the proposed fusing representations outperform the traditional representations in protein sub-nuclear localization, and the representation treated by LDA outperforms the untreated one. PMID:26703574

Evaluation of zinc coating procedures : final report.

DOT National Transportation Integrated Search

1978-01-01

This research project was conducted in order to compare the existing procedure of zinc coating by hot-dip galvanizing with the other zinc coating systems of painting and electroplating. : Hardware coated by these processes was exposed to varied labor...

Azole-based antimycotic agents inhibit mold on unseasoned pine

Treesearch

Carol. A. Clausen; Vina W. Yang

2005-01-01

Inhibiting the growth of mold fungi on cellulose-based building materials may be achievable through the use of azole-based antimycotics. Azoles were variably effective against mold fungi that are frequently found on wood and wood products. Unseasoned southern yellow pine specimens that were dip-treated with varying concentrations of eight azoles were evaluated for...

Kinematic development of the Tibetan Plateau's northern margin: A traverse across the Qilian Shan-Nan Shan thrust belt

NASA Astrophysics Data System (ADS)

Zuza, A. V.; Levy, D. A.; Wang, Z.; Xiong, X.; Chen, X.

2017-12-01

The active Cenozoic Qilian Shan-Nan Shan thrust belt defines the northern margin of the Tibetan Plateau. The kinematic development of this thrust belt has implications models of plateau growth and Himalayan-Tibetan orogen strain accommodation. We present new field observations and analytical data from a traverse across the 350-km-wide doubly vergent Qilian Shan, which is bound by the south-dipping North Qilian thrust system in the north and the north-dipping range-bounding Qinghai Nanshan-Dulan Shan thrust system in the south. These faults, and several other major thrusts within the thrust-belt interior, disrupt relatively thick Oligocene-Miocene basin deposits. Of note, many of the thrust faults across the width of the Qilian Shan have Quaternary fault scarps, indicating that active deformation is distributed and not only concentrated along the northern frontal faults. By integrating our detailed structural traverse with new geophysical observations and thermochronology data across the northern plateau margin, we construct a kinematic model for the development of the Tibetan Plateau's northern margin. Deformation initiated in the Eocene-Oligocene along the north-dipping Qinghai Nanshan-Dulan Shan and south-dipping Tuolai Nan Shan thrusts, the latter of which then defined the northern boundary of the Tibetan Plateau. This early deformation was focused along preexisting early Paleozoic structures. A 200-km-wide basin formed between these ranges, and from the Miocene to present, new thrust- and strike-slip-fault-bounded ranges developed, including the north-directed North Qilian and the south-directed Tuolai Nan thrusts. Thus, our observations do not support northward propagating thrust-belt expansion. Instead, we envision that the initial thrust-belt development generated a wide Oligocene-Miocene north-plateau basin that was subsequently disintegrated by later Miocene to present thrusting and strike-slip faulting. Ultimately, the Qilian Shan-Nan Shan thrust belt differs from a typical orogenic thrust wedge, and active deformation is distributed across the range.

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

NASA Technical Reports Server (NTRS)

Heaps, J. D.; Maciolek, R. B.; Zook, J. D.; Harrison, W. B.; Scott, M. W.; Hendrickson, G.; Wolner, H. A.; Nelson, L. D.; Schuller, T. L.; Peterson, A. A.

1976-01-01

The technical and economic feasibility of producing solar cell quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large grain polycrystalline silicon was investigated. The dip-coating methods studied were directed toward a minimum cost process with the ultimate objective of producing solar cells with a conversion efficiency of 10% or greater. The technique shows excellent promise for low cost, labor-saving, scale-up potentialities and would provide an end product of sheet silicon with a rigid and strong supportive backing. An experimental dip-coating facility was designed and constructed, several substrates were successfully dip-coated with areas as large as 25 sq cm and thicknesses of 12 micron to 250 micron. There appears to be no serious limitation on the area of a substrate that could be coated. Of the various substrate materials dip-coated, mullite appears to best satisfy the requirement of the program. An inexpensive process was developed for producing mullite in the desired geometry.

Dia-Interacting Protein (DIP) Imposes Migratory Plasticity in mDia2-Dependent Tumor Cells in Three-Dimensional Matrices

PubMed Central

Wyse, Meghan M.; Lei, Jun; Nestor-Kalinoski, Andrea L.; Eisenmann, Kathryn M.

2012-01-01

Tumor cells rely upon membrane pliancy to escape primary lesions and invade secondary metastatic sites. This process relies upon localized assembly and disassembly cycles of F-actin that support and underlie the plasma membrane. Dynamic actin generates both spear-like and bleb structures respectively characterizing mesenchymal and amoeboid motility programs utilized by metastatic cells in three-dimensional matrices. The molecular mechanism and physiological trigger(s) driving membrane plasticity are poorly understood. mDia formins are F-actin assembly factors directing membrane pliancy in motile cells. mDia2 is functionally coupled with its binding partner DIP, regulating cortical actin and inducing membrane blebbing in amoeboid cells. Here we show that mDia2 and DIP co-tether to nascent blebs and this linkage is required for bleb formation. DIP controls mesenchymal/amoeboid cell interconvertability, while CXCL12 induces assembly of mDia2:DIP complexes to bleb cortices in 3D matrices. These results demonstrate how DIP-directed mDia2-dependent F-actin dynamics regulate morphological plasticity in motile cancer cells. PMID:23024796

Internal tectonic structure of the Central American Wadati-Benioff zone based on analysis of aftershock sequences

NASA Astrophysics Data System (ADS)

Å PičáK, Aleš; Hanuš, VáClav; VaněK, JiřÃ.­; BěHounková, Marie

2007-09-01

Relocated Engdahl et al. (1998) global seismological data for 10 aftershock sequences were used to analyze the internal tectonic structure of the Central American subduction zone; the main shocks of several of these were the most destructive and often referenced earthquakes in the region (e.g., the 1970 Chiapas, 1983 Osa, 1992 Nicaragua, 1999 Quepos, 2001 El Salvador earthquakes). The spatial analysis of aftershock foci distribution was performed in a rotated Cartesian coordinate system (x, y, z) related to the Wadati-Benioff zone, and not in a standard coordinate system (ϕ, λ, h are latitude, longitude, focal depth, respectively). Available fault plane solutions were also transformed into the plane approximating the Wadati-Benioff zone. The spatial distribution of earthquakes in each aftershock sequence was modeled as either a plane fit using a least squares approximation or a volume fit with a minimum thickness rectangular box. The analysis points to a quasi-planar distribution of earthquake foci in all aftershock sequences, manifesting the appurtenance of aftershocks to fracture zones. Geometrical parameters of fracture zones (strike, dip, and dimensions) hosting individual sequences were calculated and compared with the seafloor morphology of the Cocos Plate. The smooth character of the seafloor correlates with the aftershock fracture zones oriented parallel to the trench and commonly subparallel to the subducting slab, whereas subduction of the Cocos Ridge and seamounts around the Quepos Plateau coincides with steeply dipping fracture zones. Transformed focal mechanisms are almost exclusively (>90%) of normal character.

Internal tectonic structure of the Central American Wadati-Benioff zone based on analysis of aftershock sequences

NASA Astrophysics Data System (ADS)

Špičák, Aleš; Hanuš, Václav; Vaněk, Jiří; Běhounková, Marie

2007-09-01

Relocated Engdahl et al. (1998) global seismological data for 10 aftershock sequences were used to analyze the internal tectonic structure of the Central American subduction zone; the main shocks of several of these were the most destructive and often referenced earthquakes in the region (e.g., the 1970 Chiapas, 1983 Osa, 1992 Nicaragua, 1999 Quepos, 2001 El Salvador earthquakes). The spatial analysis of aftershock foci distribution was performed in a rotated Cartesian coordinate system (x, y, z) related to the Wadati-Benioff zone, and not in a standard coordinate system ($\\varphi$, λ, h are latitude, longitude, focal depth, respectively). Available fault plane solutions were also transformed into the plane approximating the Wadati-Benioff zone. The spatial distribution of earthquakes in each aftershock sequence was modeled as either a plane fit using a least squares approximation or a volume fit with a minimum thickness rectangular box. The analysis points to a quasi-planar distribution of earthquake foci in all aftershock sequences, manifesting the appurtenance of aftershocks to fracture zones. Geometrical parameters of fracture zones (strike, dip, and dimensions) hosting individual sequences were calculated and compared with the seafloor morphology of the Cocos Plate. The smooth character of the seafloor correlates with the aftershock fracture zones oriented parallel to the trench and commonly subparallel to the subducting slab, whereas subduction of the Cocos Ridge and seamounts around the Quepos Plateau coincides with steeply dipping fracture zones. Transformed focal mechanisms are almost exclusively (>90%) of normal character.

Optical properties of titanium di-oxide thin films prepared by dip coating method

NASA Astrophysics Data System (ADS)

Biswas, Sayari; Rahman, Kazi Hasibur; Kar, Asit Kumar

2018-05-01

Titanium dioxide (TiO2) thin films were prepared by sol-gel dip coating method on ITO coated glass substrate. The sol was synthesized by hydrothermal method at 90°C. The sol was then used to make TiO2 films by dip coating. After dip coating the rest of the sol was dried at 100°C to make TiO2 powder. Thin films were made by varying the number of dipping cycles and were annealed at 500°C. XRD study was carried out for powder samples that confirms the formation of anatase phase. Transmission spectra of thin films show sharp rise in the violet-ultraviolet transition region and a maximum transmittance of ˜60%. Band gap of the prepared films varies from 3.15 eV to 3.22 eV.

Cloning and function analysis of a drought-inducible gene associated with resistance to Curvularia leaf spot in maize.

PubMed

Zhu, Jiewei; Huang, Xiuli; Liu, Tong; Gao, Shigang; Chen, Jie

2012-08-01

ZmDIP was cloned and its function against Curvularia lunata was analyzed, according to a previous finding on a drought-inducible protein in resistant maize identified through MALDI-TOF-MS/MS. The ZmDIP expression varied in roots, leaf sheaths, and young, as well as old, leaves of different maize inbred lines. The ZmDIP transcript level changed in leaves over the course of time after inoculation with C. lunata. A prokaryotic expression analysis demonstrated that the gene can regulate the salt stress tolerance of Escherichia coli. The ZmDIP transient expression in the maize leaf showed that the gene was also linked to leaf resistance against the C. lunata infection. ZmDIP-mediated ROS and ABA signaling pathways were inferred to be closely associated with maize leaf resistance to the pathogen infection.

Autoradiographic detection of diphtheria toxin resistant mutants in human diploid fibroblasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, R.S.; Singh, B.

1985-01-01

An autoradiographic procedure for the detection of diphtheria toxin (DT) resistant (Dip/sub R/) mutants in human diploid fibroblast (HDF) cells has been developed. The assay is based on the observation that when HDFs from confluent cultures are seeded in medium containing 0.01 flocculating units/ml or higher concentration of DT, protein synthesis in sensitive cells is severely inhibited by 4-6 hr. If at this or later time, a radiolabeled protein precursor (eg, /sup 3/H-leucine) is added to the culture, it is almost exclusively incorporated into the resistant cells, which are then readily identified by autoradiography. These studies provide strong evidence thatmore » the labeled cells identified by autoradiography are bona fide Dip/sub R/ mutants. The detection of Dip/sub R/ cells by autoradiography is apparently not affected by the presence of the sensitive cells in the mixtures. The spontaneous frequency of Dip/sub R/ cells in HDFs has been found to be in the range of 1-5 x 10/sup -6/, and this increases in a dose dependent manner upon treatment with the mutagen ethyl methanesulfonate. These results indicate that the autoradiographic assay could be used for quantitative mutagenesis. Since the autoradiographic assay does not depend on cell division, it may prove useful in estimating the incidence of pre-existing mutations in cell populations that either do not divide or have very limited growth potential (eg, lymphocytes, muscle cells, neurons, senescent fibroblasts, etc.).« less

Dipping-interface mapping using mode-separated Rayleigh waves

USGS Publications Warehouse

Luo, Y.; Xia, J.; Xu, Y.; Zeng, C.; Miller, R.D.; Liu, Q.

2009-01-01

Multichannel analysis of surface waves (MASW) method is a non-invasive geophysical technique that uses the dispersive characteristic of Rayleigh waves to estimate a vertical shear (S)-wave velocity profile. A pseudo-2D S-wave velocity section is constructed by aligning 1D S-wave velocity profiles at the midpoint of each receiver spread that are contoured using a spatial interpolation scheme. The horizontal resolution of the section is therefore most influenced by the receiver spread length and the source interval. Based on the assumption that a dipping-layer model can be regarded as stepped flat layers, high-resolution linear Radon transform (LRT) has been proposed to image Rayleigh-wave dispersive energy and separate modes of Rayleigh waves from a multichannel record. With the mode-separation technique, therefore, a dispersion curve that possesses satisfactory accuracy can be calculated using a pair of consecutive traces within a mode-separated shot gather. In this study, using synthetic models containing a dipping layer with a slope of 5, 10, 15, 20, or 30 degrees and a real-world example, we assess the ability of using high-resolution LRT to image and separate fundamental-mode Rayleigh waves from raw surface-wave data and accuracy of dispersion curves generated by a pair of consecutive traces within a mode-separated shot gather. Results of synthetic and real-world examples demonstrate that a dipping interface with a slope smaller than 15 degrees can be successfully mapped by separated fundamental waves using high-resolution LRT. ?? Birkh??user Verlag, Basel 2009.

KIC 8462852 Brightness Pattern Repeating Every 1600 days

NASA Astrophysics Data System (ADS)

Gary, Bruce; Bourne, Rafik

2017-12-01

Observations of KIC 8462852 (aka Boyajian's Star) reveal a yearlong fade pattern that is remarkably similar to the fade pattern derived from Kepler mission observations. The ground-based observations reported here can be described as a gradual fade that ended in late 2016 with the beginning of a yearlong U-shaped fade of 1.1 percent. Near the end of this U-shaped fade a series of very brief dips occurred. The Kepler data exhibit a similar pattern 1600 days earlier, except with an abrupt end of observations before the U-shape recovery. Observations lasting many years are needed, especially during our predicted repeat of the U-shape and short dip pattern in 2021.

Improvement of the titanium implant biological properties by coating with poly (ε-caprolactone)-based hybrid nanocomposites synthesized via sol-gel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Catauro, Michelina; Bollino, Flavia; Papale, Ferdinando

When bioactive coatings are applied to medical implants by means of sol-gel dip coating technique, the biological proprieties of the implant surface can be modified to match the properties of the surrounding tissues. In this study organo-inorganic nanocomposites materials were synthesized via sol-gel. They consisted of an inorganic zirconium-based and silica-based matrix, in which a biodegradable polymer (the poly-ε-caprolactone, PCL) was incorporated in different weight percentages. The synthesized materials, in sol phase, were used to dip-coat a substrate of commercially pure titanium grade 4 (CP Ti gr. 4) in order to improve its biological properties. A microstructural analysis of themore » obtained films was carried out by scanning electron microscopy (SEM) and attenuated total reflectance (ATR) Fourier transform infrared spectroscopy (FT-IR). Biological proprieties of the coated substrates were investigated by means of in vitro tests.« less

Glucose biosensors with enzyme entrapped in polymer coating.

PubMed

Yang, S; Atanasov, P; Wilkins, E

1995-01-01

The pursuit of reliable biosensors for measuring glucose levels has been ongoing for decades. Their importance lies partly in the development of the implantable artificial pancrease, which can be used to deliver insulin to diabetics without the need to test glucose levels externally, with automatic delivery based on physiologic demand. Glucose sensors can also be used in short-term monitoring of glucose levels in hospitals and clinical laboratories. Three types of glucose biosensors were studied. All were based on a two-electrode system: an insulated platinum wire as a hydrogen peroxide electrode, and a silver wire twisted around the platinum wire as both a reference and a counter electrode. Each was coated with the enzyme glucose oxidase entrapped in a polymer matrix of cellulose acetate (CA) or poly 2-hydroxyethyl methacrylate (HEMA), then dip-coated by an additional polymer coating of polyvinylchloride (PVC), polyurethane (PU), or HEMA. The experiments were designed mainly to study the effectiveness of polymer coatings as diffusion-limiting membranes. The effect of each coating on the linear response to glucose concentration was examined. It was shown that additional (multiple) coatings can increase the linearity of the sensor response. The best results were obtained when the sensor was PVC-dip-coated three times. This preparation had a linear response up to 600 mg/DL glucose concentration. The sensors coated with PU and HEMA have linearity up to 280 and 240 mg/DL glucose concentrations, respectively. It was also shown that the coatings reduce interference from certain body chemicals.

DISCO interacting protein 2 determines direction of axon projection under the regulation of c-Jun N-terminal kinase in the Drosophila mushroom body

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nitta, Yohei; Brain Research Institute, Niigata University; Sugie, Atsushi

Precisely controlled axon guidance for complex neuronal wiring is essential for appropriate neuronal function. c-Jun N-terminal kinase (JNK) was found to play a role in axon guidance recently as well as in cell proliferation, protection and apoptosis. In spite of many genetic and molecular studies on these biological processes regulated by JNK, how JNK regulates axon guidance accurately has not been fully explained thus far. To address this question, we use the Drosophila mushroom body (MB) as a model since the α/β axons project in two distinct directions. Here we show that DISCO interacting protein 2 (DIP2) is required formore » the accurate direction of axonal guidance. DIP2 expression is under the regulation of Basket (Bsk), the Drosophila homologue of JNK. We additionally found that the Bsk/DIP2 pathway is independent from the AP-1 transcriptional factor complex pathway, which is directly activated by Bsk. In conclusion, our findings revealed DIP2 as a novel effector downstream of Bsk modulating the direction of axon projection. - Highlights: • DIP2 is required for accurate direction of axon guidance in Drosophila mushroom body. • DIP2 is a downstream of JNK in the axon guidance of Drosophila mushroom body neuron. • JNK/DIP2 pathway is independent from JNK/AP-1 transcriptional factor complex pathway.« less

The First Post-Kepler Brightness Dips of KIC 8462852

NASA Astrophysics Data System (ADS)

Boyajian, Tabetha. S.; Alonso, Roi; Ammerman, Alex; Armstrong, David; Asensio Ramos, A.; Barkaoui, K.; Beatty, Thomas G.; Benkhaldoun, Z.; Benni, Paul; Bentley, Rory O.; Berdyugin, Andrei; Berdyugina, Svetlana; Bergeron, Serge; Bieryla, Allyson; Blain, Michaela G.; Capetillo Blanco, Alicia; Bodman, Eva H. L.; Boucher, Anne; Bradley, Mark; Brincat, Stephen M.; Brink, Thomas G.; Briol, John; Brown, David J. A.; Budaj, J.; Burdanov, A.; Cale, B.; Aznar Carbo, Miguel; Castillo García, R.; Clark, Wendy J.; Clayton, Geoffrey C.; Clem, James L.; Coker, Phillip H.; Cook, Evan M.; Copperwheat, Chris M.; Curtis, J. L.; Cutri, R. M.; Cseh, B.; Cynamon, C. H.; Daniels, Alex J.; Davenport, James R. A.; Deeg, Hans J.; De Lorenzo, Roberto; de Jaeger, Thomas; Desrosiers, Jean-Bruno; Dolan, John; Dowhos, D. J.; Dubois, Franky; Durkee, R.; Dvorak, Shawn; Easley, Lynn; Edwards, N.; Ellis, Tyler G.; Erdelyi, Emery; Ertel, Steve; Farfán, Rafael. G.; Farihi, J.; Filippenko, Alexei V.; Foxell, Emma; Gandolfi, Davide; Garcia, Faustino; Giddens, F.; Gillon, M.; González-Carballo, Juan-Luis; González-Fernández, C.; González Hernández, J. I.; Graham, Keith A.; Greene, Kenton A.; Gregorio, J.; Hallakoun, Na’ama; Hanyecz, Ottó; Harp, G. R.; Henry, Gregory W.; Herrero, E.; Hildbold, Caleb F.; Hinzel, D.; Holgado, G.; Ignácz, Bernadett; Ilyin, Ilya; Ivanov, Valentin D.; Jehin, E.; Jermak, Helen E.; Johnston, Steve; Kafka, S.; Kalup, Csilla; Kardasis, Emmanuel; Kaspi, Shai; Kennedy, Grant M.; Kiefer, F.; Kielty, C. L.; Kessler, Dennis; Kiiskinen, H.; Killestein, T. L.; King, Ronald A.; Kollar, V.; Korhonen, H.; Kotnik, C.; Könyves-Tóth, Réka; Kriskovics, Levente; Krumm, Nathan; Krushinsky, Vadim; Kundra, E.; Lachapelle, Francois-Rene; LaCourse, D.; Lake, P.; Lam, Kristine; Lamb, Gavin P.; Lane, Dave; Lau, Marie Wingyee; Lewin, Pablo; Lintott, Chris; Lisse, Carey; Logie, Ludwig; Longeard, Nicolas; Lopez Villanueva, M.; Whit Ludington, E.; Mainzer, A.; Malo, Lison; Maloney, Chris; Mann, A.; Mantero, A.; Marengo, Massimo; Marchant, Jon; Martínez González, M. J.; Masiero, Joseph R.; Mauerhan, Jon C.; McCormac, James; McNeely, Aaron; Meng, Huan Y. A.; Miller, Mike; Molnar, Lawrence A.; Morales, J. C.; Morris, Brett M.; Muterspaugh, Matthew W.; Nespral, David; Nugent, C. R.; Nugent, Katherine M.; Odasso, A.; O’Keeffe, Derek; Oksanen, A.; O’Meara, John M.; Ordasi, András; Osborn, Hugh; Ott, John J.; Parks, J. R.; Rodriguez Perez, Diego; Petriew, Vance; Pickard, R.; Pál, András; Plavchan, P.; Pollacco, Don; Pozo Nuñez, F.; Pozuelos, F. J.; Rau, Steve; Redfield, Seth; Relles, Howard; Ribas, Ignasi; Richards, Jon; Saario, Joonas L. O.; Safron, Emily J.; Sallai, J. Martin; Sárneczky, Krisztián; Schaefer, Bradley E.; Schumer, Clea F.; Schwartzendruber, Madison; Siegel, Michael H.; Siemion, Andrew P. V.; Simmons, Brooke D.; Simon, Joshua D.; Simón-Díaz, S.; Sitko, Michael L.; Socas-Navarro, Hector; Sódor, Á.; Starkey, Donn; Steele, Iain A.; Stone, Geoff; Strassmeier, Klaus G.; Street, R. A.; Sullivan, Tricia; Suomela, J.; Swift, J. J.; Szabó, Gyula M.; Szabó, Róbert; Szakáts, Róbert; Szalai, Tamás; Tanner, Angelle M.; Toledo-Padrón, B.; Tordai, Tamás; Triaud, Amaury H. M. J.; Turner, Jake D.; Ulowetz, Joseph H.; Urbanik, Marian; Vanaverbeke, Siegfried; Vanderburg, Andrew; Vida, Krisztián; Vietje, Brad P.; Vinkó, József; von Braun, K.; Waagen, Elizabeth O.; Walsh, Dan; Watson, Christopher A.; Weir, R. C.; Wenzel, Klaus; Westendorp Plaza, C.; Williamson, Michael W.; Wright, Jason T.; Wyatt, M. C.; Zheng, WeiKang; Zsidi, Gabriella

2018-01-01

We present a photometric detection of the first brightness dips of the unique variable star KIC 8462852 since the end of the Kepler space mission in 2013 May. Our regular photometric surveillance started in 2015 October, and a sequence of dipping began in 2017 May continuing on through the end of 2017, when the star was no longer visible from Earth. We distinguish four main 1%–2.5% dips, named “Elsie,” “Celeste,” “Skara Brae,” and “Angkor,” which persist on timescales from several days to weeks. Our main results so far are as follows: (i) there are no apparent changes of the stellar spectrum or polarization during the dips and (ii) the multiband photometry of the dips shows differential reddening favoring non-gray extinction. Therefore, our data are inconsistent with dip models that invoke optically thick material, but rather they are in-line with predictions for an occulter consisting primarily of ordinary dust, where much of the material must be optically thin with a size scale ≪1 μm, and may also be consistent with models invoking variations intrinsic to the stellar photosphere. Notably, our data do not place constraints on the color of the longer-term “secular” dimming, which may be caused by independent processes, or probe different regimes of a single process.

Seismicity and structure of Nazca Plate subduction zone in southern Peru

NASA Astrophysics Data System (ADS)

Lim, H.; Kim, Y.; Clayton, R. W.; Thurber, C. H.

2016-12-01

We define subducting plate geometries in the Nazca subduction zone by (re)locating intra-slab earthquakes in southern Peru (2-18°S) and taking previously published converted phase analysis results, to clarify the slab geometry and inferred relationships to the seismicity. We also provide both P- and S-wave velocities of the subducting Nazca Plate and mantle wedge portions close to the slab using double-difference tomography (Zhang and Thurber, 2003) to understand upper plate volcanism and subduction process. A total of 492 regional earthquakes from August 2008 to February 2013 recorded from the dense seismic array (PeruSE, 2013) are selected for the relocation and tomography. The relocated seismicity shows a smooth contortion in the slab-dip transition zone for 400 km between the shallow (25°)-to-flat dipping interface in the north and 40°-dipping interface in the south. We find a significant slab-dip difference (up to 10°) between our results and previously published slab models along the profile region sampling the normal-dip slab at depth (>100 km). Robust features in both P- and S-wave tomography inversions are dipping low-velocity slabs down to 100 km transitioning to higher-velocities at 100-140 km in both flat slab and dipping slab regions. Differences in the velocities of the mantle wedge between the two regions may indicate different hydration states in the wedge.

Fiber Bragg Grating Based System for Temperature Measurements

NASA Astrophysics Data System (ADS)

Tahir, Bashir Ahmed; Ali, Jalil; Abdul Rahman, Rosly

In this study, a fiber Bragg grating sensor for temperature measurement is proposed and experimentally demonstrated. In particular, we point out that the method is well-suited for monitoring temperature because they are able to withstand a high temperature environment, where standard thermocouple methods fail. The interrogation technologies of the sensor systems are all simple, low cost and effective as well. In the sensor system, fiber grating was dipped into a water beaker that was placed on a hotplate to control the temperature of water. The temperature was raised in equal increments. The sensing principle is based on tracking of Bragg wavelength shifts caused by the temperature change. So the temperature is measured based on the wavelength-shifts of the FBG induced by the heating water. The fiber grating is high temperature stable excimer-laser-induced grating and has a linear function of wavelength-temperature in the range of 0-285°C. A dynamic range of 0-285°C and a sensitivity of 0.0131 nm/°C almost equal to that of general FBG have been obtained by this sensor system. Furthermore, the correlation of theoretical analysis and experimental results show the capability and feasibility of the purposed technique.

Geomorphology and Kinematics of the Nobi-Ise Active Fault Zone, Central Japan: Implications for the kinematic growth of tectonic landforms within an active thrust belt

NASA Astrophysics Data System (ADS)

Ishiyama, T.; Mueller, K. J.; Togo, M.; Takemura, K.; Okada, A.

2002-12-01

We present structural models constrained by tectonic geomorphology, surface geologic mapping and high-resolution seismic reflection profiles to define the kinematic evolution and geometry of active fault-related folds along the Nobi-Ise active fault zone (NAFZ). The NAFZ is an active intraplate fault system in central Japan, and consists of a 110-km-long array of active, east-verging reverse faults. We focus on the northern half of the NAFZ, where we use the kinematic evolution of active fault-related folds to constrain rates of slip on underlying blind thrusts and the rate of contraction across the belt since early Quaternary time. Fluvial terraces folded across the east-dipping forelimb, and west-dipping backlimb of the frontal Kuwana anticline suggest that it grows above a stacked sequence of thin-skinned wedge thrusts. Numerous secondary, bedding-parallel thrusts also deform the terraces and are interpreted to form by flexural slip folding that acts to consume slip on the primary blind thrusts across synclinal axial surfaces. Late Holocene fold scarps formed in the floodplain of the Ibi River east of Kuwana anticline coincide with the projected surface trace of the east-vergent wedge thrust tip and indicate the structure has accommodated coseismic (?) kink-band migration of a fault-bend fold during a historic blind thrust earthquake in 1586. A topographic cross-section based on a detailed photogrammetric map suggests 111 m of uplift of ca. 50-80 ka fluvial terraces deposited across the forelimb. For a 35° thrust, this yields the minimum slip rate of 2.7-4.8 mm/yr on the deepest wedge thrust beneath Kuwana anticline. Kinematic analysis for the much larger thrust defined to the west (the Fumotomura fault) suggests that folding of fluvial terraces occurred by trishear fault-propagation folding above a more steeply-dipping (54°), basement-involved blind thrust that propagated upward from the base of the seismogenic crust (about 12 km). Pleistocene growth strata defined by tephra (ca. 1.6 Ma) suggest the Fumotomura fault slips at a rate of 0.7-0.9 mm/yr.

Implications of seismic reflection and potential field geophysical data on the structural framework of the Yucca Mountain-Crater Flat region, Nevada

USGS Publications Warehouse

Brocher, T.M.; Hunter, W.C.; Langenheim, V.E.

1998-01-01

Seismic reflection and gravity profiles collected across Yucca Mountain, Nevada, together with geologic data, provide evidence against proposed active detachment faults at shallow depth along the pre-Tertiary-Tertiary contact beneath this potential repository for high-level nuclear waste. The new geophysical data show that the inferred pre-Tertiary-Tertiary contact is offset by moderate- to high-angle faults beneath Crater Flat and Yucca Mountain, and thus this shallow surface cannot represent an active detachment surface. Deeper, low-angle detachment surface(s) within Proterozoic-Paleozoic bedrock cannot be ruled out by our geophysical data, but are inconsistent with other geologic and geophysical observations in this vicinity. Beneath Crater Flat, the base of the seismogenic crust at 12 km depth is close to the top of the reflective (ductile) lower crust at 14 to 15 km depth, where brittle fault motions in the upper crust may be converted to pure shear in the ductile lower crust. Thus, our preferred interpretation of these geophysical data is that moderate- to high-angle faults extend to 12-15-km depth beneath Yucca Mountain and Crater Flat, with only modest changes in dip. The reflection lines reveal that the Amargosa Desert rift zone is an asymmetric half-graben having a maximum depth of about 4 km and a width of about 25 km. The east-dipping Bare Mountain fault that bounds this graben to the west can be traced by seismic reflection data to a depth of at least 3.5 km and possibly as deep as 6 km, with a constant dip of 64????5??. Within Crater Flat, east-dipping high-angle normal faults offset the pre-Tertiary-Tertiary contact as well as a reflector within the Miocene tuff sequence, tilting both to the west. The diffuse eastern boundary of the Amargosa Desert rift zone is formed by a broad series of high-angle down-to-the-west normal faults extending eastward across Yucca Mountain. Along our profile the transition from east- to west-dipping faults occurs at or just west of the Solitario Canyon fault, which bounds the western side of Yucca Mountain. The interaction at depth of these east- and west-dipping faults, having up to hundreds of meters offset, is not imaged by the seismic reflection profile. Understanding potential seismic hazards at Yucca Mountain requires knowledge of the subsurface geometry of the faults near Yucca Mountain, since earthquakes generally nucleate and release the greatest amount of their seismic energy at depth. The geophysical data indicate that many fault planes near the potential nuclear waste facility dip toward Yucca Mountain, including the Bare Mountain range-front fault and several west-dipping faults east of Yucca Mountain. Thus, earthquake ruptures along these faults would lie closer to Yucca Mountain than is often estimated from their surface locations and could therefore be more damaging.

Metallurgical investigation into ductility dip cracking in nickel based alloys

NASA Astrophysics Data System (ADS)

Noecker, Fredrick F., II

A690 is a Ni-Cr-Fe alloy with excellent resistance to general corrosion, localized corrosion and stress corrosion cracking. However, the companion filler metal for A690, EN52, has been shown by several researchers to be susceptible to ductility dip cracking (DDC), which limits its widespread use in joining applications. The Gleeble hot ductility test was used to evaluate the DDC susceptibility of A600 and A690, along with their filler metals, EN82H and EN52, throughout the heating and cooling portions of a simulated weld reheat thermal cycle. Both macroscopic mechanical measures and microscopic measures of DDC were quantified and compared. Water quenching was conducted at select temperatures for subsequent microstructural characterization. Microstructural and microchemical characterization was carried out using scanning electron microscopy, transmission electron microscopy and analytical electron microscopy (AEM) techniques. The greatest resistance to DDC was observed in A600 and A690 during heating, where no DDC cracks formed even when the samples were fractured. Both A690 and EN52 were found to form an intermediate on-cooling dip in ductility and UTS, which corresponded to an increase in ductility dip crack length. The hot ductility and cracking resistance of EN82H remained high throughout the entire thermal cycle. DDC susceptibility in both EN52 and EN82H decreased when the thermal cycle was modified to promote coarsening/precipitation of intergranular carbides prior to straining. AEM analysis did not reveal any sulfur or phosphorous intergranular segregation in EN52 at 1600°F on-heating, on-cooling or after a 60 second hold. The ductility dip cracks were preferentially oriented at a 45° to the tensile axis and were of a wedge type appearance, both of which are characteristic of grain boundary sliding (GBS). Samples with microstructures that consisted of coarsened carbides and/or serrated grain boundaries, which are expected to decrease GBS, were found to be resistant to DDC. Based on the results of this work grain boundary sliding contributes to DDC, while sulfur and phosphorous embrittlement do not play a role in DDC of EN52 at the concentrations investigated. The dynamic precipitation of partially coherent intergranular M23C6 carbides at intermediate temperatures may exacerbate DDC in A690 and EN52, but requires further investigation.

The Dip. H.E. Coombe Lodge Report, Study Confererence 74/43.

ERIC Educational Resources Information Center

Further Education Staff Coll., Blagdon (England).

Papers presented on the Dip. H.E., a two-year course in higher education recently developed in Britain include: the future of higher education (W. Taylor); the colleges of education perspective on the Dip. H.E. (N. Payne); the colleges of further education perspective (W. Bosley); the polytechnics perspective (A. Sandbach); validating the diploma…

9 CFR 72.15 - Owners assume responsibility; must execute agreement prior to dipping or treatment waiving all...

Code of Federal Regulations, 2010 CFR

2010-01-01

... CATTLE § 72.15 Owners assume responsibility; must execute agreement prior to dipping or treatment waiving all claims against United States. When the cattle are to be dipped under APHIS supervision the owner of the cattle, offered for shipment, or his agent duly authorized thereto, shall first execute and...

9 CFR 73.2 - Interstate shipment for immediate slaughter from quarantined or nonquarantined areas; conditions...

Code of Federal Regulations, 2014 CFR

2014-01-01

... INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS SCABIES IN CATTLE § 73.2..., were affected with scabies but have been dipped once in a permitted dip (other than a toxaphene dip... herd not visibly affected. Cattle of the free area not visibly diseased with scabies, but which may be...

9 CFR 73.2 - Interstate shipment for immediate slaughter from quarantined or nonquarantined areas; conditions...

Code of Federal Regulations, 2011 CFR

2011-01-01

... INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS SCABIES IN CATTLE § 73.2..., were affected with scabies but have been dipped once in a permitted dip (other than a toxaphene dip... herd not visibly affected. Cattle of the free area not visibly diseased with scabies, but which may be...

9 CFR 73.2 - Interstate shipment for immediate slaughter from quarantined or nonquarantined areas; conditions...

Code of Federal Regulations, 2013 CFR

2013-01-01

... INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS SCABIES IN CATTLE § 73.2..., were affected with scabies but have been dipped once in a permitted dip (other than a toxaphene dip... herd not visibly affected. Cattle of the free area not visibly diseased with scabies, but which may be...

9 CFR 73.2 - Interstate shipment for immediate slaughter from quarantined or nonquarantined areas; conditions...

Code of Federal Regulations, 2012 CFR

2012-01-01

... INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS SCABIES IN CATTLE § 73.2..., were affected with scabies but have been dipped once in a permitted dip (other than a toxaphene dip... herd not visibly affected. Cattle of the free area not visibly diseased with scabies, but which may be...

21 CFR 529.1044b - Gentamicin solution for dipping eggs.

Code of Federal Regulations, 2014 CFR

2014-04-01

....600(c) of this chapter. (c) Conditions of use in turkeys—(1) Amount. The drug is added to clean water...) Indications for use. As an aid in the reduction or elimination of the following microorganisms from turkey...) Limitations. For use in the dipping treatment of turkey-hatching eggs only. Eggs which have been dipped in the...

10 Fun Facts About U.S. Pacific Command | DoDLive

Science.gov Websites

, Singapore, Malaysia, Japan, Australia, Peru, Chile, Mexico and Canada. The PACOM area is home to more than DipNote - U.S. Dept. of State Military Health System Navy Blog Navy Medicine Live Purview: Space &

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operations from fire, you must have in place: (i) Automatic sprinklers; or (ii) An automatic fire... the alarm set point, you must equip the tank with a circulating cooling system. (5) If the tank has a bottom drain, the bottom drain may be combined with the oil-circulating system. (6) You must not use air...

29 CFR 1910.126 - Additional requirements for special dipping and coating operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operations from fire, you must have in place: (i) Automatic sprinklers; or (ii) An automatic fire... the alarm set point, you must equip the tank with a circulating cooling system. (5) If the tank has a bottom drain, the bottom drain may be combined with the oil-circulating system. (6) You must not use air...

A Seismic Source Model for Central Europe and Italy

NASA Astrophysics Data System (ADS)

Nyst, M.; Williams, C.; Onur, T.

2006-12-01

We present a seismic source model for Central Europe (Belgium, Germany, Switzerland, and Austria) and Italy, as part of an overall seismic risk and loss modeling project for this region. A separate presentation at this conference discusses the probabilistic seismic hazard and risk assessment (Williams et al., 2006). Where available we adopt regional consensus models and adjusts these to fit our format, otherwise we develop our own model. Our seismic source model covers the whole region under consideration and consists of the following components: 1. A subduction zone environment in Calabria, SE Italy, with interface events between the Eurasian and African plates and intraslab events within the subducting slab. The subduction zone interface is parameterized as a set of dipping area sources that follow the geometry of the surface of the subducting plate, whereas intraslab events are modeled as plane sources at depth; 2. The main normal faults in the upper crust along the Apennines mountain range, in Calabria and Central Italy. Dipping faults and (sub-) vertical faults are parameterized as dipping plane and line sources, respectively; 3. The Upper and Lower Rhine Graben regime that runs from northern Italy into eastern Belgium, parameterized as a combination of dipping plane and line sources, and finally 4. Background seismicity, parameterized as area sources. The fault model is based on slip rates using characteristic recurrence. The modeling of background and subduction zone seismicity is based on a compilation of several national and regional historic seismic catalogs using a Gutenberg-Richter recurrence model. Merging the catalogs encompasses the deletion of double, fake and very old events and the application of a declustering algorithm (Reasenberg, 2000). The resulting catalog contains a little over 6000 events, has an average b-value of -0.9, is complete for moment magnitudes 4.5 and larger, and is used to compute a gridded a-value model (smoothed historical seismicity) for the region. The logic tree weighs various completeness intervals and minimum magnitudes. Using a weighted scheme of European and global ground motion models together with a detailed site classification map for Europe based on Eurocode 8, we generate hazard maps for recurrence periods of 200, 475, 1000 and 2500 yrs.

CSI 2264: Characterizing Young Stars in NGC 2264 With Short-Duration Periodic Flux Dips in Their Light Curves

NASA Technical Reports Server (NTRS)

Stauffer, John; Cody, Ann Marie; McGinnis, Pauline; Rebull, Luisa; Hillenbrand, Lynne A.; Turner, Neal J.; Carpenter, John; Plavchan, Peter; Carey, Sean; Terebey, Susan;

Acid-triggered core cross-linked nanomicelles for targeted drug delivery and magnetic resonance imaging in liver cancer cells

PubMed Central

Li, Xian; Li, Hao; Yi, Wei; Chen, Jianyu; Liang, Biling

2013-01-01

Purpose To research the acid-triggered core cross-linked folate-poly(ethylene glycol)-b-poly[N-(N′,N′-diisopropylaminoethyl) glutamine] (folated-PEG-P[GA-DIP]) amphiphilic block copolymer for targeted drug delivery and magnetic resonance imaging (MRI) in liver cancer cells. Methods As an appropriate receptor of protons, the N,N-diisopropyl tertiary amine group (DIP) was chosen to conjugate with the side carboxyl groups of poly(ethylene glycol)-b-poly (L-glutamic acid) to obtain PEG-P(GA-DIP) amphiphilic block copolymers. By ultrasonic emulsification, PEG-P(GA-DIP) could be self-assembled to form nanosized micelles loading doxorubicin (DOX) and superparamagnetic iron oxide nanoparticles (SPIONs) in aqueous solution. When PEG-P(GA-DIP) nanomicelles were combined with folic acid, the targeted effect of folated-PEG-P(GA-DIP) nanomicelles was evident in the fluorescence and MRI results. Results To further increase the loading efficiency and the cell-uptake of encapsulated drugs (DOX and SPIONs), DIP (pKa≈6.3) groups were linked with ~50% of the side carboxyl groups of poly(L-glutamic acid) (PGA), to generate the core cross-linking under neutral or weakly acidic conditions. Under the acidic condition (eg, endosome/lysosome), the carboxyl groups were neutralized to facilitate disassembly of the P(GA-DIP) blocks’ cross-linking, for duly accelerating the encapsulated drug release. Combined with the tumor-targeting effect of folic acid, specific drug delivery to the liver cancer cells and MRI diagnosis of these cells were greatly enhanced. Conclusion Acid-triggered and folate-decorated nanomicelles encapsulating SPIONs and DOX, facilitate the targeted MRI diagnosis and therapeutic effects in tumors. PMID:23976852

The effects of local anaesthetic solution in the navicular bursa of horses with lameness caused by distal interphalangeal joint pain.

PubMed

Schumacher, John; Schumacher, Jim; Gillette, R; DeGraves, F; Schramme, M; Smith, R; Perkins, J; Coker, M

2003-07-01

Analgesia of the palmar digital (PD) nerves has been demonstrated to cause analgesia of the distal interphalangeal (DIP) joint as well as the sole. Because the PD nerves lie in close proximity to the navicular bursa, we suspected that that analgesia of the navicular bursa would anaesthetise the PD nerves, which would result in analgesia of the DIP joint. To determine the response of horses with pain in the DIP joint to instillation of local anaesthetic solution into the navicular bursa. Lameness was induced in 6 horses by creating painful synovitis in the DIP joint of one forefoot by administering endotoxin into the joint. Horses were videorecorded while trotting, before and after induction of lameness, at three 10 min intervals after instilling 3.5 ml local anaesthetic solution into the navicular bursa and, finally, after instilling 6 ml solution into the DIP joint. Lameness scores were assigned by grading the videorecorded gaits subjectively. At the 10 and -20 min observations, median lameness scores were not significantly different from those before administration of local anaesthetic solution into the navicular bursa (P > or = 0.05), although lameness scores of 3 of 6 horses improved during this period, and the 20 min observation scores tended toward significance (P = 0.07). At the 30 min observation, and after analgesia of the DIP joint, median lameness scores were significantly improved (P < or = 0.05). These results indicate that pain arising from the DIP joint can probably be excluded as a cause of lameness, when lameness is attenuated within 10 mins by analgesia of the navicular bursa. Pain arising from the DIP joint cannot be excluded as a cause of lameness when lameness is attenuated after 20 mins after analgesia of the navicular bursa.

The interhemispheric and F region dynamo currents revisited with the Swarm constellation

NASA Astrophysics Data System (ADS)

Lühr, Hermann; Kervalishvili, Guram; Michaelis, Ingo; Rauberg, Jan; Ritter, Patricia; Park, Jaeheung; Merayo, Jose M. G.; Brauer, Peter

2015-05-01

Based on magnetic field data sampled by the Swarm satellite constellation it is possible for the first time to determine uniquely F region currents at low latitudes. Initial results are presented from the first 200 days of formation flight (17 April to 5 November 2014). Detailed results have been obtained for interhemispheric field-aligned currents connecting the solar quiet day magnetic variation (Sq) current systems in the two hemispheres. We obtain prominent currents from the Southern (winter) Hemisphere to the Northern around noon. Weaker currents in opposite direction are observed during morning and evening hours. Furthermore, we could confirm the existence of vertical currents above the dip equator, downward around noon and upward around sunset. For both current systems we present and discuss longitudinal variations.

Assessing the Role of Dissolved Organic Phosphate on Rates of Microbial Phosphorus Cycling

NASA Astrophysics Data System (ADS)

Gonzalez, A. C.; Popendorf, K. J.; Duhamel, S.

2016-02-01

Phosphorus (P) is an element crucial to life, and it is limiting in many parts of the ocean. In oligotrophic environments, the dissolved P pool is cycled rapidly through the activity of microbes, with turnover times of several hours or less. The overarching aim of this study was to assess the flux of P from picoplankton to the dissolved pool and the role this plays in fueling rapid P cycling. To determine if specific microbial groups are responsible for significant return of P to the dissolved pool during cell lifetime, we compared the rate of cellular P turnover (cell-Pτ, the rate of cellular P uptake divided by cellular P content) to the rate of cellular biomass turnover (cellτ). High rates of P return to the dissolved pool during cell lifetime (high cell-Pτ/cellτ) indicate significant P regeneration, fueling more rapid turnover of the dissolved P pool. We hypothesized that cell-Pτ/cellτ varies widely across picoplankton groups. One factor influencing this variation may be each microbial group's relative uptake of dissolved organic phosphorus (DOP) versus dissolved inorganic phosphorus (DIP). As extracellular hydrolysis is necessary for P incorporation from DOP, this process may return more P to the dissolved pool than DIP incorporation. This leads to the question: does a picoplankton's relative uptake of DOP (versus DIP) affect the rate at which it returns phosphorus to the dissolved pool? To address this question, we compared the rate of cellular P turnover based on uptake of DOP and uptake DIP using cultured representatives of three environmentally significant picoplankton groups: Prochlorococcus, Synechococcus, and heterotrophic bacteria. These different picoplankton groups are known to take up different ratios of DOP to DIP, and may in turn make significantly different contributions to the regeneration and cycling phosphorus. These findings have implications towards our understanding of the timeframes of biogeochemical cycling of phosphorus in the ocean.

The July 12, 1993, Hokkaido-Nansei-Oki, Japan, earthquake: Coseismic slip pattern from strong-motion and teleseismic recordings

USGS Publications Warehouse

Mendoza, C.; Fukuyama, E.

1996-01-01

We employ a finite fault inversion scheme to infer the distribution of coseismic slip for the July 12, 1993, Hokkaido-Nansei-Oki earthquake using strong ground motions recorded by the Japan Meteorological Agency within 400 km of the epicenter and vertical P waveforms recorded by the Global Digital Seismograph Network at teleseismic distances. The assumed fault geometry is based on the location of the aftershock zone and comprises two fault segments with different orientations: a northern segment striking at N20??E with a 30?? dip to the west and a southern segment with a N20??W strike. For the southern segment we use both westerly and easterly dip directions to test thrust orientations previously proposed for this portion of the fault. The variance reduction is greater using a shallow west dipping segment, suggesting that the direction of dip did not change as the rupture propagated south from the hypocenter. This indicates that the earthquake resulted from the shallow underthrusting of Hokkaido beneath the Sea of Japan. Static vertical movements predicted by the corresponding distribution of fault slip are consistent with the general pattern of surface deformation observed following the earthquake. Fault rupture in the northern segment accounts for about 60% of the total P wave seismic moment of 3.4 ?? 1020 N m and includes a large circular slip zone (4-m peak) near the earthquake hypocenter at depths between 10 and 25 km. Slip in the southern segment is also predominantly shallower than 25 km, but the maximum coseismic displacements (2.0-2.5 m) are observed at a depth of about 5 km. This significant shallow slip in the southern portion of the rupture zone may have been responsible for the large tsunami that devastated the small offshore island of Okushiri. Localized shallow faulting near the island, however, may require a steep westerly dip to reconcile the measured values of ground subsidence.

An epidemic of East Coast fever on a dairy farm in eastern Tanzania.

PubMed

Msami, H M

2001-04-13

During the period August-September 1995, an epidemic of East Coast fever occurred at a dairy farm in Morogoro region of eastern Tanzania. Due to an intensive dipping scheme since 1970, a very unstable endemic status had been established in the animals. A breakdown in the dipping scheme caused a major disease outbreak; the dip wash was not changed for 18 months prior to the outbreak and dipping continued in a dip wash of unknown strength. There was also a delay in detecting the disease at an early stage. In total, 180 out of 432 (42%) of the cattle at the farm died--resulting in a loss of Tshs. 26,330,000 (US$ 42,879). The attack risk was nearly 77%. The outbreak points to the importance of adopting integrated strategies for the control of ticks and tick-borne diseases.

Ion blocking dip shape analysis around a LaAlO3/SrTiO3 interface

NASA Astrophysics Data System (ADS)

Jalabert, D.; Zaid, H.; Berger, M. H.; Fongkaew, I.; Lambrecht, W. R. L.; Sehirlioglu, A.

2018-05-01

We present an analysis of the widths of the blocking dips obtained in MEIS ion blocking experiments of two LaAlO3/SrTiO3 heterostructures differing in their LaAlO3 layer thicknesses. In the LaAlO3 layers, the observed blocking dips are larger than expected. This enlargement is the result of the superposition of individual dips at slightly different angular positions revealing a local disorder in the atomic alignment, i.e., layer buckling. By contrast, in the SrTiO3 substrate, just below the interface, the obtained blocking dips are thinner than expected. This thinning indicates that the blocking atoms stand at a larger distance from the scattering center than expected. This is attributed to an accumulation of Sr vacancies at the layer/substrate interface which induces lattice distortions shifting the atoms off the scattering plane.

Nanoscale Spectroscopic Imaging of Organic Semiconductor Films by Plasmon-Polariton Coupling

NASA Astrophysics Data System (ADS)

Zhang, D.; Heinemeyer, U.; Stanciu, C.; Sackrow, M.; Braun, K.; Hennemann, L. E.; Wang, X.; Scholz, R.; Schreiber, F.; Meixner, A. J.

2010-02-01

Tip-enhanced near-field optical images and correlated topographic images of an organic semiconductor film (diindenoperylene, DIP) on Si have been recorded with high optical contrast and high spatial resolution (17 nm) using a parabolic mirror with a high numerical aperture for tip illumination and signal collection. The DIP molecular domain boundaries being one to four molecular layers (1.5-6 nm) high are resolved topographically by a shear-force scanning tip and optically by simultaneously recording the 6×105 times enhanced photoluminescence (PL). The excitation is 4×104 times enhanced and the intrinsically weak PL-yield of the DIP-film is 15-fold enhanced by the tip. The Raman spectra indicate an upright orientation of the DIP molecules. The enhanced PL contrast results from the local film morphology via stronger coupling between the tip plasmon and the exciton-polariton in the DIP film.

Crust-mantle boundaries in the Taiwan - Luzon arc-continent collision system determined from local earthquake tomography and layered Vp models

NASA Astrophysics Data System (ADS)

Ustaszewski, K. M.; Wu, Y.; Suppe, J.; Huang, H.; Carena, S.; Chang, C.

2011-12-01

We performed 3D mapping of crust-mantle boundaries in the Taiwan-Luzon arc-continent collision zone using a local earthquake tomographic model, providing better insight into the mode of subduction polarity reversal. The mapped crust-mantle discontinuities include three tectonically distinct Mohos. Furthermore, a crust-mantle boundary marks the eastern limit of the Eurasian lower crust against the mantle of the Philippine Sea plate. It dips steeply to the east underneath eastern and southern Taiwan and steepens progressively towards north until it becomes vertical at 23.7°N. From there it continues northward in a slightly overturned orientation, where the limit of the tomographic model at the northern tip of the island prevents further mapping. In order to map several Moho discontinuities, we contoured a surface of constant Vp = 7.5 km s-1 constrained from local earthquake tomography and confined to regions with a minimum of 500 rays per tomography cell. Additional constraints for the Moho were derived from layered (1D) Vp models using P-wave arrivals of local earthquakes recorded at 52 seismic stations, employing a genetic algorithm. The Moho of the Eurasian and the Philippine Sea plates are topologically disconnected across the plate boundary. Beneath southern Taiwan, the Eurasian Moho dips to the E at 50-60°, following the orientation of the plate boundary and continuous with the Benioff zone. Towards north, the Eurasian Moho twists to become subvertical, again together with the plate boundary. At the same time, it steps westward into a more external position underneath the thrust belt, giving way to the north-dipping Philippine Sea plate. The Philippine Sea plate Moho shallows towards the surface along the Longitudinal Valley suture. It forms a synform-like crustal root with an axis parallel to the trend of geological units at surface and it is interpreted as the base of the magmatic Luzon arc. Towards the north, the crustal root deepens from 30 km to about 70 km underneath the Ryukyu trench. In northeasternmost Taiwan, a subhorizontal Moho lies at about 30-35 km depth and is topologically disconnected from the main eastward subducting Eurasian Moho. It lies above the north-dipping Philippine Sea slab and is interpreted to be a newly formed Moho established by delamination of the Eurasian mantle lithosphere and lowermost crust.

Inkjet Deposition of Layer by Layer Assembled Films

PubMed Central

Andres, Christine M.; Kotov, Nicholas A.

2010-01-01

Layer-by-layer assembly (LBL) can create advanced composites with exceptional properties unavailable by other means, but the laborious deposition process and multiple dipping cycles hamper their utilization in microtechnologies and electronics. Multiple rinse steps provide both structural control and thermodynamic stability to LBL multilayers but they significantly limit their practical applications and contribute significantly to the processing time and waste. Here we demonstrate that by employing inkjet technology one can deliver the necessary quantities of LBL components required for film build-up without excess, eliminating the need for repetitive rinsing steps. This feature differentiates this approach from all other recognized LBL modalities. Using a model system of negatively charged gold nanoparticles and positively charged poly(diallyldimethylammonium) chloride, the material stability, nanoscale control over thickness and particle coverage offered by the inkjet LBL technique are shown to be equal or better than the multilayers made with traditional dipping cycles. The opportunity for fast deposition of complex metallic patterns using a simple inkjet printer was also shown. The additive nature of LBL deposition based on the formation of insoluble nanoparticle-polyelectrolyte complexes of various compositions provides an excellent opportunity for versatile, multi-component, and non-contact patterning for the simple production of stratified patterns that are much needed in advanced devices. PMID:20863114

Producing armyworm (spodoptera sp.) Bioinsecticide based on cysteine protease of red ginger (zingiber officinale var. Rubrum)

NASA Astrophysics Data System (ADS)

Afnan, N. T.; Nur, D. F.; Utami, T. S.; Sahlan, M.; Wijanarko, A.; Hermansyah, H.

2018-03-01

Armyworm (Spodoptera sp.) is highly polyphagous defoliator on various horticulture and grain plants. Various chemical insecticides have been created to control it. There is a need to create an eco-friendly and specific insecticide which only affect armyworm’s nervous system. This research investigates cysteine-protease’s enzyme activity of red ginger (Zingiber officinale var. Rubrum) which is called zingibain. Its catalytic site matches with residue site in armyworm’s body so it can be used as bioinsecticide raw material which meets the criterias above. Fresh red ginger rhizomes were washed and extracted. The juice was then deposited in low temperature and centrifuged to get rid of its starch content. It was filtrated to remove large contaminants and poured into Potassium Phospate buffer. The liquid was then centrifuged again for 30 minutes before collecting the supernatant. Fresh leaves were then dipped into crude ginger protease extract and fed to fourth instar-armyworms. Leaves dipped into non-diluted extract were barely eaten by armyworm while the 50% and 25% dilution was half eaten and most eaten. The crude red ginger extract was not strong enough to kill them although the research showed its enzymatic activity reaches up to 169 PU. It still needs improvement to be produced as commercial bioinsecticide.

Depth of Small Scale Landslide in Slate Area : Case of 2009 Typhoon Morakot in Ai-Liao River, South Taiwan

NASA Astrophysics Data System (ADS)

Chen, T. C.; Yen, H. Y.; Zhou, F. L.

2015-12-01

This study focuses on the depth and magnitude of the small scale landslide in slate area in Ai-Liao-Shi catchment, South Taiwan. Landslide inventory of 2009 Typhoon Morakot, 5×5 m DEM, and aero photo have been interpreted by GIS software to assess the slope type and the scale of landslide events. The research database includes 276 landslides which orthographic projection areas are smaller than 1 ha. The slopes were also classified into dip, orthoclinical-dip, escarpment, and orthoclinical- escarpment 4 types of slope based on the slope aspect to the bedding orientation. The sliding plane, or so call the failure plane, was identified by aero photo, field reconnaissance and verification, and DEM before and after the typhoon event. Colluvium material deposited on the slip plane was removed based on the scarp and foot position, mass movement pattern, weak plane orientation, and the micro topography of a landslide to achieve the reasonable sliding plane. The maximum depth of sliding surface is explored through the slope type and sliding plane in total of 276 landslide cases. Results demonstrate that the average maximum depth, Dam, of dip slope is 4.6 m, Dam of orthoclinical-dip, escarpment, and orthoclinical-escarpment slopes are 5.8, 6.0, and 6.3 m respectively. In general, Dam is creasing with the average slope of landslide, the relationship of both factor is achieved in the study. Meanwhile, the orthographic projection area of landslide is increasing with the slope angle till the angle up to 40 degree then decreasing. The depth also varies with landslide magnitude. Finally, the relation of the depth normal to slope surface and the depth in gravity direction of landslides in four types slope are proposed, the R square values are 0.862 to 0.891 showing a good correlation between two types of depth.

The 1999 Hector Mine Earthquake, Southern California: Vector Near-Field Displacements from ERS InSAR

NASA Technical Reports Server (NTRS)

Sandwell, David T.; Sichoix, Lydie; Smith, Bridget

2002-01-01

Two components of fault slip are uniquely determined from two line-of-sight (LOS) radar interferograms by assuming that the fault-normal component of displacement is zero. We use this approach with ascending and descending interferograms from the ERS satellites to estimate surface slip along the Hector Mine earthquake rupture. The LOS displacement is determined by visually counting fringes to within 1 km of the outboard ruptures. These LOS estimates and uncertainties are then transformed into strike- and dip-slip estimates and uncertainties; the transformation is singular for a N-S oriented fault and optimal for an E-W oriented fault. In contrast to our previous strike-slip estimates, which were based only on a descending interferogram, we now find good agreement with the geological measurements, except at the ends of the rupture. The ascending interferogram reveals significant west-sidedown dip-slip (approximately 1.0 m) which reduces the strike-slip estimates by 1 to 2 m, especially along the northern half of the rupture. A spike in the strike-slip displacement of 6 m is observed in central part of the rupture. This large offset is confirmed by subpixel cross correlation of features in the before and after amplitude images. In addition to strike slip and dip slip, we identify uplift and subsidence along the fault, related to the restraining and releasing bends in the fault trace, respectively. Our main conclusion is that at least two look directions are required for accurate estimates of surface slip even along a pure strike-slip fault. Models and results based only on a single look direction could have major errors. Our new estimates of strike slip and dip slip along the rupture provide a boundary condition for dislocation modeling. A simple model, which has uniform slip to a depth of 12 km, shows good agreement with the observed ascending and descending interferograms.

Study on conditional probability of surface rupture: effect of fault dip and width of seismogenic layer

NASA Astrophysics Data System (ADS)

Inoue, N.

2017-12-01

The conditional probability of surface ruptures is affected by various factors, such as shallow material properties, process of earthquakes, ground motions and so on. Toda (2013) pointed out difference of the conditional probability of strike and reverse fault by considering the fault dip and width of seismogenic layer. This study evaluated conditional probability of surface rupture based on following procedures. Fault geometry was determined from the randomly generated magnitude based on The Headquarters for Earthquake Research Promotion (2017) method. If the defined fault plane was not saturated in the assumed width of the seismogenic layer, the fault plane depth was randomly provided within the seismogenic layer. The logistic analysis was performed to two data sets: surface displacement calculated by dislocation methods (Wang et al., 2003) from the defined source fault, the depth of top of the defined source fault. The estimated conditional probability from surface displacement indicated higher probability of reverse faults than that of strike faults, and this result coincides to previous similar studies (i.e. Kagawa et al., 2004; Kataoka and Kusakabe, 2005). On the contrary, the probability estimated from the depth of the source fault indicated higher probability of thrust faults than that of strike and reverse faults, and this trend is similar to the conditional probability of PFDHA results (Youngs et al., 2003; Moss and Ross, 2011). The probability of combined simulated results of thrust and reverse also shows low probability. The worldwide compiled reverse fault data include low fault dip angle earthquake. On the other hand, in the case of Japanese reverse fault, there is possibility that the conditional probability of reverse faults with less low dip angle earthquake shows low probability and indicates similar probability of strike fault (i.e. Takao et al., 2013). In the future, numerical simulation by considering failure condition of surface by the source fault would be performed in order to examine the amount of the displacement and conditional probability quantitatively.

Tertiary structural evolution of the Gangdese thrust system southeastern Tibet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin, An; Harrison, M.; Ryerson, F.J.

1994-09-10

Structural and thermochronological investigations of southern Tibet (Xizang) suggest that intracontinental thrusting has been the dominant cause for formation of thickened crust in the southernmost Tibetan plateau since late Oligocene. Two thrust systems are documented in this study: the north dipping Gangdese system (GTS) and the younger south dipping Renbu-Zedong system (RZT). West of Lhasa, the Gangdese thrust juxtaposes the Late Cretaceous forearc basin deposits of the Lhasa Block (the Xigaze Group) over the Tethyan sedimentary rocks of the Indian plate, whereas east of Lhasa, the fault juxtaposes the Late Cretaceous-Eocene, Andean-type arc (the Gangdese batholith) over Tethyan sedimentary rocks.more » Near Zedong, 150 km southeast of Lhasa, the Gangdese thrust is marked by a >200-m-thick mylonitic shear zone that consists of deformed granite and metasedimentary rocks. A major south dipping backthrust in the hanging wall of the Gangdese thrust puts the Xigaze Group over Tertiary conglomerates and the Gangdese plutonics north of Xigaze and west of Lhasa. A lower age bound for the Gangdese thrust of 18.3{+-}0.5 Ma is given by crosscutting relationships. The timing of slip on the Gangdese thrust is estimate to be 27-23 Ma from {sup 40}Ar/{sup 39}Ar thermochronology, and a displacement of at least 46{+-}9 km is indicated near Zedong. The age of the Gangdese thrust (GT) is consistent with an upper age limit of {approximately}24 Ma for the initiation of movement on the Main Central thrust. In places, the younger Renbu-Zedong fault is thrust over the trace of the GT, obscuring its exposure. The RZT appears to have been active at circa 18 Ma but had ceased movement by 8{+-}1 Ma. The suture between India and Asia has been complexely modified by development of the GTS, RZT, and, locally, strike-slip and normal fault systems. 64 refs., 14 figs., 2 tabs.« less

29 CFR 1910.123 - Dipping and coating operations: Coverage and definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... tank containing a liquid other than water. It applies when you use the liquid in the tank or its vapor... combustion, independent of any other source of heat. Dip tank means a container holding a liquid other than... dip tank or it may be suspended in a vapor coming from the tank. Flammable liquid means any liquid...

[Prevention of intramammary infections in dairy cows by the use of a premilking teat dip method with a foaming iodophor dip agent].

PubMed

Falkenberg, U; Tenhagen, B A; Baumgärtner, B; Heuwieser, W

2002-10-01

In this study we investigated the efficacy of premilking teat dipping with a foaming iodophor teat dip in a negative controlled field study. Incidence of new intramammary infections (IMI), incidence of clinical mastitis, influence on somatic cell count (SCC) and the characteristics of udder tissue and teats were used as parameters to evaluate clinical efficacy. Predipping was compared with a negative control using a split-udder experimental design. Right teats were predipped with a foaming disinfectant containing 0.27% iodine while left teats served as controls. The latter were conventionally cleaned with damp cloth towels and dried manually with disposable paper towels ("best cleaning practice"). All teats were dipped after milking with the same dip. There were no differences between treated and control quarters with respect to incidence of new IMI during the study period (treated quarters: 6.6% vs. untreated: 6.95%), incidence of clinical mastitis (30 cases in the treatment group vs. 39 cases in the control group) and geometric mean of SCC of quarter milk samples. Spectrum of detected pathogens was also comparable. Condition of udder tissue and teat ducts did not differ between treated and control quarters.

Modeling Slab-Slab Interactions: Dynamics of Outward Dipping Double-Sided Subduction Systems

NASA Astrophysics Data System (ADS)

Király, Ágnes; Holt, Adam F.; Funiciello, Francesca; Faccenna, Claudio; Capitanio, Fabio A.

2018-03-01

Slab-slab interaction is a characteristic feature of tectonically complex areas. Outward dipping double-sided subduction is one of these complex cases, which has several examples on Earth, most notably the Molucca Sea and Adriatic Sea. This study focuses on developing a framework for linking plate kinematics and slab interactions in an outward dipping subduction geometry. We used analog and numerical models to better understand the underlying subduction dynamics. Compared to a single subduction model, double-sided subduction exhibits more time-dependent and vigorous toroidal flow cells that are elongated (i.e., not circular). Because both the Molucca and Adriatic Sea exhibit an asymmetric subduction configuration, we also examine the role that asymmetry plays in the dynamics of outward dipping double-sided subduction. We introduce asymmetry in two ways; with variable initial depths for the two slabs ("geometric" asymmetry), and with variable buoyancy within the subducting plate ("mechanical" asymmetry). Relative to the symmetric case, we probe how asymmetry affects the overall slab kinematics, whether asymmetric behavior intensifies or equilibrates as subduction proceeds. While initial geometric asymmetry disappears once the slabs are anchored to the 660 km discontinuity, the mechanical asymmetry can cause more permanent differences between the two subduction zones. In the most extreme case, the partly continental slab stops subducting due to the unequal slab pull force. The results show that the slab-slab interaction is most effective when the two trenches are closer than 10-8 cm in the laboratory, which is 600-480 km when scaled to the Earth.

Low Charge States of Si and S: from Cygnus X-1 to the Lab and Back

NASA Astrophysics Data System (ADS)

Hell, Natalie; Miškovičova, I.; Hanke, M.; Brown, G. V.; Wilms, J.; Clementson, J.; Beiersdorfer, P.; Liedahl, D. A.; Pottschmidt, K.; Porter, F.; Kilbourne, C.; Kelley, R. L.; Nowak, M.; Schulz, N. S.

2013-04-01

The X-ray light curves of the high mass X-ray binary (HMXB) Cygnus X-1 are shaped by strong, relatively short, absorption dips. While spectra extracted from the dip free phases are dominated by absorption lines of the Rydberg series of H- and He-like ions, 1s-2p transitions of lower ionized Si and S appear in the dip spectra. This shift in charge balance suggests that we probe “clumps” of cold material embedded in the companion's stellar wind as they cross our line of sight. Determining the bulk motion of these clumps by measuring the Doppler shifts of these lines as a function of dipping strength and ionization state can confirm this theory. Unfortunately, the predicted uncertainty for theoretical calculations - if available at all - is of the order of the expected shifts in the system. To overcome this lack of reliable reference wavelengths, we measured the Kα spectra of H- through F-like Si and S with the EBIT Calorimeter Spectrometer (ECS) and the Lawrence Livermore National Laboratory electron beam ion trap EBIT-I. We then directly apply these new line centers to calculate the Doppler shifts of the lines observed in Cygnus X-1. With this approach, we find shifts consistent with constant velocity of the absorber throughout all ionization states and, hence, provide evidence for an onion-like ion structure of the clumps. Funded by BMWi under DLR grant 50OR1207. Work at LLNL was performed under the auspices of DOE under contract DE-AC52-07NA27344 and supported by NASA grants.

Adaptive finite element modelling of three-dimensional magnetotelluric fields in general anisotropic media

NASA Astrophysics Data System (ADS)

Liu, Ying; Xu, Zhenhuan; Li, Yuguo

2018-04-01

We present a goal-oriented adaptive finite element (FE) modelling algorithm for 3-D magnetotelluric fields in generally anisotropic conductivity media. The model consists of a background layered structure, containing anisotropic blocks. Each block and layer might be anisotropic by assigning to them 3 × 3 conductivity tensors. The second-order partial differential equations are solved using the adaptive finite element method (FEM). The computational domain is subdivided into unstructured tetrahedral elements, which allow for complex geometries including bathymetry and dipping interfaces. The grid refinement process is guided by a global posteriori error estimator and is performed iteratively. The system of linear FE equations for electric field E is solved with a direct solver MUMPS. Then the magnetic field H can be found, in which the required derivatives are computed numerically using cubic spline interpolation. The 3-D FE algorithm has been validated by comparisons with both the 3-D finite-difference solution and 2-D FE results. Two model types are used to demonstrate the effects of anisotropy upon 3-D magnetotelluric responses: horizontal and dipping anisotropy. Finally, a 3D sea hill model is modelled to study the effect of oblique interfaces and the dipping anisotropy.

Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

NASA Astrophysics Data System (ADS)

Keong, C. C.; Zin, W. M. Wan; Ibrahim, P.; Ibrahim, S.

2010-05-01

Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

Regenerated cellulose capsules for controlled drug delivery: Part III. Developing a fabrication method and evaluating extemporaneous utility for controlled-release.

PubMed

Bhatt, Bhavik; Kumar, Vijay

2016-08-25

In this article, we describe a method to utilize cellulose dissolved in dimethyl sulfoxide and paraformaldehyde solvent system to fabricate two-piece regenerated cellulose hard shell capsules for their potential use as an oral controlled drug delivery a priori vehicle. A systematic evaluation of solution rheology as well as resulting capsule mechanical, visual and thermal analysis was performed to develop a suitable method to repeatedly fabricate RC hard shell capsule halves. Because of the viscoelastic nature of the cellulose solution, a combination of dip-coating and casting method, herein referred to as dip-casting method, was developed. The dip-casting method was formalized by utilizing two-stage 2(2) full factorial design approach in order to determine a suitable approach to fabricate capsules with minimal variability. Thermal annealing is responsible for imparting shape rigidity of the capsules. Proof-of-concept analysis for the utility of these capsules in controlled drug delivery was performed by evaluating the release of KCl from them as well as from commercially available USP equivalent formulations. Release of KCl from cellulose capsules was comparable to extended release capsule formulation. Copyright © 2016 Elsevier B.V. All rights reserved.

Compartmentalization of the Coso East Flank geothermal field imaged by 3-D full-tensor MT inversion

USGS Publications Warehouse

Lindsey, Nathaniel J.; Kaven, Joern; Davatzes, Nicholas C.; Newman, Gregory A.

2017-01-01

Previous magnetotelluric (MT) studies of the high-temperature Coso geothermal system in California identified a subvertical feature of low resistivity (2–5 Ohm m) and appreciable lateral extent (>1 km) in the producing zone of the East Flank field. However, these models could not reproduce gross 3-D effects in the recorded data. We perform 3-D full-tensor inversion and retrieve a resistivity model that out-performs previous 2-D and 3-D off-diagonal models in terms of its fit to the complete 3-D MT data set as well as the degree of modelling bias. Inclusion of secondary Zxx and Zyy data components leads to a robust east-dip (60†) to the previously identified conductive East Flank reservoir feature, which correlates strongly with recently mapped surface faults, downhole well temperatures, 3-D seismic reflection data, and local microseismicity. We perform synthetic forward modelling to test the best-fit dip of this conductor using the response at a nearby MT station. We interpret the dipping conductor as a fractured and fluidized compartment, which is structurally controlled by an unmapped blind East Flank fault zone.

Compartmentalization of the Coso East Flank geothermal field imaged by 3-D full-tensor MT inversion

NASA Astrophysics Data System (ADS)

Lindsey, Nathaniel J.; Kaven, Joern Ole; Davatzes, Nicholas; Newman, Gregory A.

2017-02-01

Previous magnetotelluric (MT) studies of the high-temperature Coso geothermal system in California identified a subvertical feature of low resistivity (2-5 Ohm m) and appreciable lateral extent (>1 km) in the producing zone of the East Flank field. However, these models could not reproduce gross 3-D effects in the recorded data. We perform 3-D full-tensor inversion and retrieve a resistivity model that out-performs previous 2-D and 3-D off-diagonal models in terms of its fit to the complete 3-D MT data set as well as the degree of modelling bias. Inclusion of secondary Zxx and Zyy data components leads to a robust east-dip (60†) to the previously identified conductive East Flank reservoir feature, which correlates strongly with recently mapped surface faults, downhole well temperatures, 3-D seismic reflection data, and local microseismicity. We perform synthetic forward modelling to test the best-fit dip of this conductor using the response at a nearby MT station. We interpret the dipping conductor as a fractured and fluidized compartment, which is structurally controlled by an unmapped blind East Flank fault zone.

Structural evidence for slip partitioning and inclined dextral transpression along the SE Sanandaj-Sirjan zone, Iran

NASA Astrophysics Data System (ADS)

Shafiei Bafti, Shahram; Mohajjel, Mohammad

2015-04-01

The structural evolution of the Sanandaj-Sirjan zone is the result of the convergence of the Iranian microcontinent and the Afro-Arabian continent. The study area at Khabr in the SE Sanandaj-Sirjan zone, in the hinterland of the Zagros orogen, consists of Paleozoic, Mesozoic and Cenozoic rocks. In this area, deformation phases were distinguished in different rock units based on structural and stratigraphical evidence, and the deformational events are divided into two stages: (1) a Late Triassic event and (2) a Late Cretaceous to Miocene event. The Late Triassic deformation event caused regional metamorphism in the Paleozoic units. These units are overlain by unmetamorphosed Jurassic clastic sequences. Fabrics and structural evidence confirm that the F1 folding recumbent and refolded folds were synchronous with the metamorphism of the Paleozoic units and terminated in the Early Jurassic. The time table of the orogenic phases shows that this deformation event is related to the Cimmerian orogenic phase. From a geodynamic point of view, the early Cimmerian deformation in the southeastern Iranian margin suggests that the SE Sanandaj-Sirjan zone was an active margin at that time. The early Cimmerian discordance recorded the onset of a contractional component related to the oblique subduction of Neo-Tethys beneath the central Iranian microcontinent. Structures related to the Late Cretaceous to Miocene deformation phase are observed in Jurassic to Oligocene units, which contain moderately inclined and plunging folds. Comparing these folds with domains of deformation generated in models of transpression shows that the folding was caused by a combination of contractional and dip-slip components of movement, eventually resulting in the formation of a thrust system. The Khabr thrust systems consist of five sheets of oblique thrusts, duplex structures and shear zones. The shear zones generally strike E-W and dip moderately N (30°-40°). The occurrence of asymmetric folds with hinges that are either parallel to strike or plunge down dip demonstrates an oblique-slip component in these thrust shear zones. The stretching lineation in the mylonites within the shear zones is defined by the long axes of ellipsoidal grains of quartz, calcite, plagioclase and garnet. In general, stretching lineations trend from N40°W to N80°W with an intermediate (35°) plunge. The geometry of foliation and lineation within these shear zones shows the effect of dip- and oblique-slip shearing. Deformation continued with strike-slip faulting becoming important during the last stages of deformation from the Miocene to the present day. The results of this study demonstrate that the evolution of the SE Sanandaj-Sirjan zone, from Late Triassic to Miocene, is compatible with an inclined dextral transpression along this zone.

Controls on bedrock bedform development at the base of the Uummannaq Ice Stream System, West Greenland

NASA Astrophysics Data System (ADS)

Lane, Tim; Roberts, David; Rea, Brice; Cofaigh, Colm Ó.

2014-05-01

This research investigates the glacial and non-glacial controls on glacially eroded bedrock bedforms beneath the topographically confined upstream fjord region of the Uummannaq Ice Stream (UIS), West Greenland. The UIS was a cross-shelf ice stream system that operated during the Last Glacial Maximum (LGM), formed of 10 coalescent outlet glaciers. Reconstructions suggest that palaeo-glaciological conditions were similar for all sites in the study, characterised by thick, fast flowing ice moving over a rigid bedrock bed. Areally scoured terrain were mapped using remotely sensed imagery to assess regional-scale patterns of glacial erosion and to select suitable field locations. In the field, bedform measurements were taken from four discrete areas within two neighbouring fjords in the northern Uummannaq region (Rink-Karrat and Ingia). Classic bedrock bedforms indicative of glacially eroded terrain were mapped, including p-forms, roche moutonnées, and whalebacks. Bedform long axes and plucked face orientations display close correlation with palaeo-ice flow directions inferred from striae measurements. Across all sites, elongation ratios (length to width) varied by an order of magnitude between 0.8:1 and 8.4:1. Bedform properties (length, height, width, and long axis orientation) from the four sample areas form individual morphometrically distinct populations. However, bedform populations display high inter-area variability despite their close proximity, and hypothesised similarity in palaeo-glaciological conditions. The relationship of bedforms to palaeo-glaciological conditions in this study is not simple, having been complicated by bedrock properties. Geological structures including: joint frequency; joint dip; joint orientation; bedding plane thickness; and bedding plane dip have provided lines of geological weakness along which glacial erosion has been able to focus, controlling bedform length and width. Lateral plucking, a mechanism previously described for the development of megagroove features, is invoked here for the formation of whaleback-type bedforms in Ingia Fjord. Bedding plane thickness and bedding plane dip relative to palaeo-ice flow direction and is shown to a key control on bedform morphology and ELR. Consequently, a knowledge of bedding plane dip relative to palaeo-ice flow can allow predictions to be made about likely bedform shape, relative length, amplitude, and wavelength. These predictions have important ramifications for understanding subglacial bed roughness, cavity formation, and likely ice-bed erosion processes. These observations demonstrate the direct link between bedrock bedform properties and underlying geological structure. This supports evidence which suggests that the use of bedrock bedform characteristics to directly infer palaeo-glaciological conditions must be approached with caution. In order to robustly understand bedform morphology, a full appreciation of local geological structure is necessary.

DISCOVERY OF RAPIDLY MOVING PARTIAL X-RAY ABSORBERS WITHIN GAMMA CASSIOPEIAE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamaguchi, K.; Oskinova, L.; Russell, C. M. P.

2016-12-01

Gamma Cassiopeiae is an enigmatic Be star with unusually strong hard X-ray emission. The Suzaku observatory detected six rapid X-ray spectral hardening events called “softness dips” in a ∼100 ks observation in 2011. All the softness dip events show symmetric softness-ratio variations, and some of them have flat bottoms apparently due to saturation. The softness dip spectra are best described by either ∼40% or ∼70% partial covering absorption to kT  ∼ 12 keV plasma emission by matter with a neutral hydrogen column density of ∼(2−8) × 10{sup 21} cm{sup −2}, while the spectrum outside these dips is almost free of absorption. This resultmore » suggests the presence of two distinct X-ray-emitting spots in the γ  Cas system, perhaps on a white dwarf (WD) companion with dipole mass accretion. The partial covering absorbers may be blobs in the Be stellar wind, the Be disk, or rotating around the WD companion. Weak correlations of the softness ratios to the hard X-ray flux suggest the presence of stable plasmas at kT  ∼ 0.9 and 5 keV, which may originate from the Be or WD winds. The formation of a Be star and WD binary system requires mass transfer between two stars; γ  Cas may have experienced such activity in the past.« less

Infection of Douglas-fir by Leptographium wageneri.

Treesearch

Paul F. Hessburg; Everett M. Hansen

2000-01-01

In three related experiments, root systems of 2-year-old Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) seedlings were dip-inoculated with a viscous blend of Leptographium wageneri var. pseudotsugae Harrington and Cobb spores and hyphal fragments and planted in a sterile potting medium. Infection...

46 CFR 128.220 - Class II non-vital systems-materials and pressure design.

Code of Federal Regulations, 2013 CFR

2013-10-01

... materials and pressure design of subchapter F of this chapter. (b) Piping for salt-water service must be of a corrosion-resistant material and, if ferrous, be hot-dip galvanized or be at least of extra-heavy...

46 CFR 128.220 - Class II non-vital systems-materials and pressure design.

Code of Federal Regulations, 2014 CFR

2014-10-01

... materials and pressure design of subchapter F of this chapter. (b) Piping for salt-water service must be of a corrosion-resistant material and, if ferrous, be hot-dip galvanized or be at least of extra-heavy...

46 CFR 128.220 - Class II non-vital systems-materials and pressure design.

Code of Federal Regulations, 2010 CFR

2010-10-01

... materials and pressure design of subchapter F of this chapter. (b) Piping for salt-water service must be of a corrosion-resistant material and, if ferrous, be hot-dip galvanized or be at least of extra-heavy...

46 CFR 128.220 - Class II non-vital systems-materials and pressure design.

Code of Federal Regulations, 2011 CFR

2011-10-01

... materials and pressure design of subchapter F of this chapter. (b) Piping for salt-water service must be of a corrosion-resistant material and, if ferrous, be hot-dip galvanized or be at least of extra-heavy...

46 CFR 128.220 - Class II non-vital systems-materials and pressure design.

Code of Federal Regulations, 2012 CFR

2012-10-01

... materials and pressure design of subchapter F of this chapter. (b) Piping for salt-water service must be of a corrosion-resistant material and, if ferrous, be hot-dip galvanized or be at least of extra-heavy...

Earthquake scaling laws for rupture geometry and slip heterogeneity

NASA Astrophysics Data System (ADS)

Thingbaijam, Kiran K. S.; Mai, P. Martin; Goda, Katsuichiro

2016-04-01

We analyze an extensive compilation of finite-fault rupture models to investigate earthquake scaling of source geometry and slip heterogeneity to derive new relationships for seismic and tsunami hazard assessment. Our dataset comprises 158 earthquakes with a total of 316 rupture models selected from the SRCMOD database (http://equake-rc.info/srcmod). We find that fault-length does not saturate with earthquake magnitude, while fault-width reveals inhibited growth due to the finite seismogenic thickness. For strike-slip earthquakes, fault-length grows more rapidly with increasing magnitude compared to events of other faulting types. Interestingly, our derived relationship falls between the L-model and W-model end-members. In contrast, both reverse and normal dip-slip events are more consistent with self-similar scaling of fault-length. However, fault-width scaling relationships for large strike-slip and normal dip-slip events, occurring on steeply dipping faults (δ~90° for strike-slip faults, and δ~60° for normal faults), deviate from self-similarity. Although reverse dip-slip events in general show self-similar scaling, the restricted growth of down-dip fault extent (with upper limit of ~200 km) can be seen for mega-thrust subduction events (M~9.0). Despite this fact, for a given earthquake magnitude, subduction reverse dip-slip events occupy relatively larger rupture area, compared to shallow crustal events. In addition, we characterize slip heterogeneity in terms of its probability distribution and spatial correlation structure to develop a complete stochastic random-field characterization of earthquake slip. We find that truncated exponential law best describes the probability distribution of slip, with observable scale parameters determined by the average and maximum slip. Applying Box-Cox transformation to slip distributions (to create quasi-normal distributed data) supports cube-root transformation, which also implies distinctive non-Gaussian slip distributions. To further characterize the spatial correlations of slip heterogeneity, we analyze the power spectral decay of slip applying the 2-D von Karman auto-correlation function (parameterized by the Hurst exponent, H, and correlation lengths along strike and down-slip). The Hurst exponent is scale invariant, H = 0.83 (± 0.12), while the correlation lengths scale with source dimensions (seismic moment), thus implying characteristic physical scales of earthquake ruptures. Our self-consistent scaling relationships allow constraining the generation of slip-heterogeneity scenarios for physics-based ground-motion and tsunami simulations.

Spectral features of the tunneling-induced transparency and the Autler-Townes doublet and triplet in a triple quantum dot.

PubMed

Luo, Xiao-Qing; Li, Zeng-Zhao; Jing, Jun; Xiong, Wei; Li, Tie-Fu; Yu, Ting

2018-02-15

We theoretically investigate the spectral features of tunneling-induced transparency (TIT) and Autler-Townes (AT) doublet and triplet in a triple-quantum-dot system. By analyzing the eigenenergy spectrum of the system Hamiltonian, we can discriminate TIT and double TIT from AT doublet and triplet, respectively. For the resonant case, the presence of the TIT does not exhibit distinguishable anticrossing in the eigenenergy spectrum in the weak-tunneling regime, while the occurrence of double anticrossings in the strong-tunneling regime shows that the TIT evolves to the AT doublet. For the off-resonance case, the appearance of a new detuning-dependent dip in the absorption spectrum leads to double TIT behavior in the weak-tunneling regime due to no distinguished anticrossing occurring in the eigenenergy spectrum. However, in the strong-tunneling regime, a new detuning-dependent dip in the absorption spectrum results in AT triplet owing to the presence of triple anticrossings in the eigenenergy spectrum. Our results can be applied to quantum measurement and quantum-optics devices in solid systems.

Effects of analgesia of the distal interphalangeal joint or palmar digital nerves on lameness caused by solar pain in horses.

PubMed

Schumacher, J; Steiger, R; Schumacher, J; de Graves, F; Schramme, M; Smith, R; Coker, M

2000-01-01

To determine if pain of the dorsal margin of the sole in horses can be attenuated by anesthesia of either the distal interphalangeal (DIP) joint or the palmar digital (PD) nerves. A unilateral forelimb lameness was induced by creating solar pain. Response to administration of local anesthetic or saline solution into the DIP joint and to administration of local anesthetic around the PD nerves was evaluated. Six horses. Lameness was induced by creating pressure on the dorsal margin of the sole by screwing set-screws into a nut welded to the inside of each branch of a shoe. Gaits were evaluated before and after application of set-screws and after a local anesthetic or saline solution was administered into the DIP joint and, in a second trial, after a local anesthetic was injected around the PD nerves. Gaits recorded on videotape were evaluated, and lameness scores were assigned to each gait. Lameness scores were high after application of set-screws and remained high after saline solution was administered into the DIP joint. Scores decreased significantly (P < or = .05) after a local anesthetic was administered into the DIP joint or around the PD nerves. Analgesia of the DIP joint or the PD nerves desensitizes at least a portion of the sole. Pain arising from the sole should not be excluded as a cause of lameness when lameness is attenuated by analgesia of the DIP joint or PD nerves.

Frontal compression along the Apennines thrust system: The Emilia 2012 example from seismicity to crustal structure

NASA Astrophysics Data System (ADS)

Chiarabba, Claudio; De Gori, Pasquale; Improta, Luigi; Lucente, Francesco Pio; Moretti, Milena; Govoni, Aladino; Di Bona, Massimo; Margheriti, Lucia; Marchetti, Alessandro; Nardi, Anna

2014-12-01

The evolution of the Apennines thrust-and-fold belt is related to heterogeneous process of subduction and continental delamination that generates extension within the mountain range and compression on the outer front of the Adria lithosphere. While normal faulting earthquakes diffusely occur along the mountain chain, the sparse and poor seismicity in the compressional front does not permit to resolve the ambiguity that still exists about which structure accommodates the few mm/yr of convergence observed by geodetic data. In this study, we illustrate the 2012 Emilia seismic sequence that is the most significant series of moderate-to-large earthquakes developed during the past decades on the compressional front of the Apennines. Accurately located aftershocks, along with P-wave and Vp/Vs tomographic models, clearly reveal the geometry of the thrust system, buried beneath the Quaternary sediments of the Po Valley. The seismic sequence ruptured two distinct adjacent thrust faults, whose different dip, steep or flat, accounts for the development of the arc-like shape of the compressional front. The first shock of May 20 (Mw 6.0) developed on the middle Ferrara thrust that has a southward dip of about 30°. The second shock of May 29 (Mw 5.8) ruptured the Mirandola thrust that we define as a steep dipping (50-60°) pre-existing (Permo-Triassic) basement normal fault inverted during compression. The overall geometry of the fault system is controlled by heterogeneity of the basement inherited from the older extension. We also observe that the rupture directivity during the two main-shocks and the aftershocks concentration correlate with low Poisson ratio volumes, probably indicating that portions of the fault have experienced intense micro-damage.

Development of hand rehabilitation system for paralysis patient - universal design using wire-driven mechanism.

PubMed

Yamaura, Hiroshi; Matsushita, Kojiro; Kato, Ryu; Yokoi, Hiroshi

2009-01-01

We have developed a hand rehabilitation system for patients suffering from paralysis or contracture. It consists of two components: a hand rehabilitation machine, which moves human finger joints with motors, and a data glove, which provides control of the movement of finger joints attached to the rehabilitation machine. The machine is based on the arm structure type of hand rehabilitation machine; a motor indirectly moves a finger joint via a closed four-link mechanism. We employ a wire-driven mechanism and develop a compact design that can control all three joints (i.e., PIP, DIP and MP ) of a finger and that offers a wider range of joint motion than conventional systems. Furthermore, we demonstrate the hand rehabilitation process, finger joints of the left hand attached to the machine are controlled by the finger joints of the right hand wearing the data glove.

50 CFR 216.240 - Specified activity and specified geographical region.

Code of Federal Regulations, 2010 CFR

2010-10-01

... average of 216 hours per year). (4) AN/BQQ-10 or 5 (submarine sonar)—up to 49880 pings over the course of... dips over the course of 5 years (an average of 2952 dips per year—10 pings per five-minute dip). (6..., between these 2 sources, over the course of 5 years (an average of 872 buoys per year). (10) AN/SQQ-32...

50 CFR 216.270 - Specified activity and specified geographical region.

Code of Federal Regulations, 2010 CFR

2010-10-01

... over the course of 5 years (an average of 494 hours per year) (iii) AN/BQQ-10 (submarine active sonar... helicopter dipping sonar)—up to 13595 dips over the course of 5 years (an average of 2719 dips per year—10... (SINKEX)—up to 10 exercises over the course of 5 years (an average of 2 per year) (E) Extended Echo...

50 CFR 216.270 - Specified activity and specified geographical region.

Code of Federal Regulations, 2011 CFR

2011-10-01

... over the course of 5 years (an average of 494 hours per year) (iii) AN/BQQ-10 (submarine active sonar... helicopter dipping sonar)—up to 13595 dips over the course of 5 years (an average of 2719 dips per year—10... course of 5 years (an average of 40 per year) (D) Sinking Exercises (SINKEX)—up to 10 exercises over the...

An Electron Density Model above the Sunspot from a Mapping of NOAA 7260 at 17 GHz

NASA Astrophysics Data System (ADS)

Yu, Xing-Feng; Yao, Jin-Xing Yao

2002-06-01

The brightness temperature distribution of microwave emission in a solar active region generally shows a ring structure, with a dip at the centre. However, no dip was found in the Nobeyama Radioheliograph left handed circular polarization (LCP) image on 1992 August 18; instead, there was a peak. This is a completely LCP source with zero right-handed circular polarization (RCP). We examine this structure in terms of the joint effect of gyroresonance and bremsstrahlung mechanism with a raised electron density above the central part of the sunspot, and the commonly assumed temperature and vertical dipole magnetic field models. The raised electron density is found to be 1.4 × 1011 cm-3 at the chromosphere base.

Synthesis Characterization and DNA Interaction Studies of a New Zn(II) Complex Containing Different Dinitrogen Aromatic Ligands

PubMed Central

Shahabadi, Nahid; Mohammadi, Somaye

2012-01-01

A mononuclear complex of Zn(II), [Zn(DIP)2 (DMP)] (NO3)2 ·2H2O in which DIP is 4,7-diphenyl-1,10-phenanthroline and DMP is 4,4′-dimethyl-2,2′-bipyridine has been prepared and characterized by 1HNMR spectroscopy, FT-IR, UV-Vis and elemental analysis techniques. DNA-binding properties of the complex were studied using UV-vis spectra, circular dichroism (CD) spectra, fluorescence, cyclic voltammetry (CV), and viscosity measurements. The results indicate that this zinc(II) complex can intercalate into the stacked base pairs of DNA and compete with the strong intercalator ethidium bromide for the intercalative binding sites. PMID:22956919

Optofluidic refractive-index sensor in step-index fiber with parallel hollow micro-channel.

PubMed

Lee, H W; Schmidt, M A; Uebel, P; Tyagi, H; Joly, N Y; Scharrer, M; Russell, P St J

2011-04-25

We present a simple refractive index sensor based on a step-index fiber with a hollow micro-channel running parallel to its core. This channel becomes waveguiding when filled with a liquid of index greater than silica, causing sharp dips to appear in the transmission spectrum at wavelengths where the glass-core mode phase-matches to a mode of the liquid-core. The sensitivity of the dip-wavelengths to changes in liquid refractive index is quantified and the results used to study the dynamic flow characteristics of fluids in narrow channels. Potential applications of this fiber microstructure include measuring the optical properties of liquids, refractive index sensing, biophotonics and studies of fluid dynamics on the nanoscale.

Collision tectonics of the Central Indian Suture zone as inferred from a deep seismic sounding study

USGS Publications Warehouse

Mall, D.M.; Reddy, P.R.; Mooney, W.D.

2008-01-01

The Central Indian Suture (CIS) is a mega-shear zone extending for hundreds of kilometers across central India. Reprocessing of deep seismic reflection data acquired across the CIS was carried out using workstation-based commercial software. The data distinctly indicate different reflectivity characteristics northwest and southeast of the CIS. Reflections northwest of the CIS predominantly dip southward, while the reflection horizons southeast of the CIS dip northward. We interpret these two adjacent seismic fabric domains, dipping towards each other, to represent a suture between two crustal blocks. The CIS itself is not imaged as a sharp boundary, probably due to the disturbed character of the crust in a 20 to 30-km-wide zone. The time sections also show the presence of strong bands of reflectors covering the entire crustal column in the first 65??km of the northwestern portion of the profile. These reflections predominantly dip northward creating a domal structure with the apex around 30??km northwest of the CIS. There are a very few reflections in the upper 2-2.5??s two-way time (TWT), but the reflectivity is good below 2.5??s TWT. The reflection Moho, taken as the depth to the deepest set of reflections, varies in depth from 41 to 46??km and is imaged sporadically across the profile with the largest amplitude occurring in the northwest. We interpret these data as recording the presence of a mid-Proterozoic collision between two micro-continents, with the Satpura Mobile Belt being thrust over the Bastar craton. ?? 2008.

Origin of the Nubian and similar sandstones

USGS Publications Warehouse

McKee, E.D.

1963-01-01

The Nubian Sandstone and similar sandstone bodies exposed across much of northern Africa and adjoining parts of Asia are characteristically formed of clean sand that is conspicuously cross stratified throughout. Such sandstone, here called Nubian-type sandstone, ranges from Cambrian through Cretaceous in age and its genesis has been interpreted in many ways. Studies of its primary structures, and of the direction of sand transport, based on statistical measurements of foreset dip directions, have contributed new data on its genesis. By far the most common structure in Nubian-type sandstone is a medium-scale planar-type cross stratification in which sets of evenly dipping cross beds are bounded by essentially flat-lying top and bottom surfaces to form tabular bodies. Other less numerous but typical structures are large-scale, truncated-wedge cross strata, trough-type cross strata, intraformational recumbent folds, small-scale ripple laminae, and dipping sets of tabular-planar cross beds. An analysis of these structures suggests that in the typical Nubian Sandstone of Cretaceous age eolian deposits are not represented and normal marine types probably also are lacking; flood plain, pond or lagoon, and other continental and marginal environments are indicated. In the Carboniferous rocks of Sinai Peninsula some beach sandstone and possibly some eolian, in addition to the types described, form part of the sequence. Direction of sand transport, as determined from cross-bed dips, was northerly in the Cretaceous Nubian of Libya, Sudan, and Egypt; easterly in the Jurassic Adigrat of Ethiopia; westerly in the Carboniferous of Sinai; northwesterly in the early Paleozoic of Jordan. ?? 1963 Ferdinand Enke Verlag Stuttgart.

Nonlinear optical spectra having characteristics of Fano interferences in coherently coupled lowest exciton biexciton states in semiconductor quantum dots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gotoh, Hideki, E-mail: gotoh.hideki@lab.ntt.co.jp; Sanada, Haruki; Yamaguchi, Hiroshi

2014-10-15

Optical nonlinear effects are examined using a two-color micro-photoluminescence (micro-PL) method in a coherently coupled exciton-biexciton system in a single quantum dot (QD). PL and photoluminescence excitation spectroscopy (PLE) are employed to measure the absorption spectra of the exciton and biexciton states. PLE for Stokes and anti-Stokes PL enables us to clarify the nonlinear optical absorption properties in the lowest exciton and biexciton states. The nonlinear absorption spectra for excitons exhibit asymmetric shapes with peak and dip structures, and provide a distinct contrast to the symmetric dip structures of conventional nonlinear spectra. Theoretical analyses with a density matrix method indicatemore » that the nonlinear spectra are caused not by a simple coherent interaction between the exciton and biexciton states but by coupling effects among exciton, biexciton and continuum states. These results indicate that Fano quantum interference effects appear in exciton-biexciton systems at QDs and offer important insights into their physics.« less

Mixing-Induced Anisotropic Correlations in Molecular Crystalline Systems: Rationalizing the Behavior of Organic Semiconductor Blends

NASA Astrophysics Data System (ADS)

Broch, Katharina; Aufderheide, Antje; Novak, Jiri; Hinderhofer, Alexander; Gerlach, Alexander; Banerjee, Rupak; Schreiber, Frank

2013-03-01

Binary mixtures of organic semiconductors (OSCs) have recently become an important field of research, as they find applications in opto-electronic devices. In these systems, the mixing (intermixing vs. phase separation) and ordering behavior is crucial, since it affects the optical and electronic properties. We present a comprehensive study of binary mixtures of the three prototypical OSCs pentacene (PEN), perfluoropentacene (PFP) and diindenoperlyene (DIP) in all possible combinations. Using X-ray reflectivity and grazing incidence X-ray diffraction we investigate the stuctural properties of the mixed films as well as their impact on the optical spectra obtained by spectroscopic ellipsometry. For PEN:DIP we find an anisotropic ordering behavior, comparable to that observed in some liquid crystals, which is fundamentally new for OSCs. The influence of sterical compatibility and the strength of the intermolecular interactions on the mixing and ordering behavior in the different blends will be discussed by extending a conventional mean-field model. Finally, we discuss general rules for the targeted preparation of blends of OSCs.

Greener corona discharge for enhanced wind generation with a simple dip-coated carbon nanotube decoration

NASA Astrophysics Data System (ADS)

Wu, Yishan; Li, Jun; Ye, Jianchun; Chen, Xiaohong; Li, Huili; Huang, Sumei; Zhao, Ran; Ou-Yang, Wei

2017-10-01

Corona discharge-induced wind (CDIW) has been widely utilized in production lines in the food and semiconductor industries and in indoor devices such as electrostatic precipitators. Some ozone is inevitably emitted, posing serious health risks to respiratory system and lung function of a human being. In this work, a greener corona discharge with enhanced wind generation for a needle-to-cylinder discharge structure is demonstrated using a simple dip-coating method to attach carbon nanotubes (CNTs) to the discharge electrode of a stainless steel needle. Compared with a conventional discharge electrode without CNT decoration, the velocity of the CDIW is greatly enhanced, the onset voltage is lowered, the energy conversion efficiency is greatly improved and the concentration of generated ozone is much reduced, making this easy method of CNT decoration a promising candidate for greener corona discharge systems. In addition, several impact factors for improved performance are discussed mathematically and phenomenologically, providing an insight into the corona discharge and wind generation.

Characteristics of fractures in crystalline bedrock determined by surface and borehole geophysical surveys, eastern surplus superfund site, Meddybemps, Maine

USGS Publications Warehouse

Hansen, Bruce P.; Stone, Janet Radway; Lane, John W.

1999-01-01

Surface and borehole geophysical methods were used to determine fracture orientation in crystalline bedrock at the Eastern Surplus Superfund Site in Meddybemps, Maine. Fracture-orientation information is needed to address concerns about the fate of contaminants in ground water at the site. Azimuthal square-array resistivity surveys were conducted at 3 locations at the site, borehole-acoustic televiewer and borehole-video logs were collected in 10 wells, and single-hole directional radar surveys were conducted in 9 wells. Borehole-video logs were used to supplement the results of other geophysical techniques and are not described in this report. Analysis of azimuthal square-array resistivity data indicated that high-angle fracturing generally strikes northeast-southwest at the three locations. Borehole-acoustic televiewer logs detected one prominent low-angle and two prominent high-angle fracture sets. The low-angle fractures strike generally north-northeast and dip about 20 degrees west-northwest. One high-angle fracture set strikes north-northeast and dips east-southeast; the other high-angle set strikes east-northeast and dips south-southeast. Single-hole directional radar surveys identified two prominent fracture sets: a low-angle set striking north-northeast, dipping west-northwest; and a high-angle fracture set striking north-northeast, dipping east-southeast. Two additional high-angle fracture sets are defined weakly, one striking east-west, dipping north; and a second striking east-west, dipping south. Integrated results from all of the geophysical surveys indicate the presence of three primary fracture sets. A low-angle set strikes north-northeast and dips west-northwest. Two high-angle sets strike north-northeast and east-northeast and dip east-southeast and south-southeast. Statistical correction of the fracture data for orientation bias indicates that high-angle fractures are more numerous than observed in the data but are still less numerous than the low-angle fractures. The orientation and distribution of water-yielding fractures sets were determined by correlating the fracture data from this study with previously collected borehole-flowmeter data. The water-yielding fractures are generally within the three prominent fracture sets observed for the total fracture population. The low-angle water-yielding fractures primarily strike north-northeast to west-northwest and dip west-northwest to south-southwest. Most of the high-angle water-yielding fractures strike either north-northeast or east-west and dip east-southeast or south. The spacing between water-yielding fractures varies but the probable average spacing is estimated to be 30 feet for low-angle fractures; 27 feet for the east-southeast dipping, high-angle fractures; and 43 feet for the south-southeast dipping, high-angle fractures. The median estimated apparent transmissivity of individual water-yielding fractures or fracture zones was 0.3 feet squared per day and ranged from 0.01 to 382 feet squared per day. Ninety-five percent of the water-yielding fractures or fracture zones had an estimated apparent transmissivity of 19.5 feet squared per day or less. The orientation, spacing, and hydraulic properties of water-yielding fractures identified during this study can be used to help estimate recharge, flow, and discharge of ground water contaminants. High-angle fractures provide vertical pathways for ground water to enter the bedrock, interconnections between low-angle fractures, and, subsequently, pathways for water flow within the bedrock along fracture planes. Low-angle fractures may allow horizontal ground-water flow in all directions. The orientation of fracturing and the hydraulic properties of each fracture set strongly affect changes in ground-water flow under stress (pumping) conditions.

Blue light aids in coping with the post-lunch dip: an EEG study.

PubMed

Baek, Hongchae; Min, Byoung-Kyong

2015-01-01

The 'post-lunch dip' is a commonly experienced period of drowsiness in the afternoon hours. If this inevitable period can be disrupted by an environmental cue, the result will be enhanced workplace performance. Because blue light is known to be a critical cue for entraining biological rhythms, we investigated whether blue light illumination can be a practical strategy for coping with the post-lunch dip. Twenty healthy participants underwent a continuous performance test, during which the electroencephalogram (EEG) was recorded under four different illumination conditions: dark ( < 0.3 lx), 33% blue-enriched light, 66% blue-enriched light and white polychromatic light. As a result, exposure to blue-enriched light during the post-lunch dip period significantly reduced the EEG alpha activity, and increased task performance. Since desynchronisation of alpha activity reflects enhancement of vigilance, our findings imply that blue light might disrupt the post-lunch dip. Subsequent exploration of illumination parameters will be beneficial for possible chronobiological and ergonomic applications.

UV spectroscopy of Z Chamaeleontis. I - Time dependent dips in superoutburst

NASA Technical Reports Server (NTRS)

Harlaftis, E. T.; Hassall, B. J. M.; Naylor, T.; Charles, P. A.; Sonneborn, G.

1992-01-01

Extensive IUE observations of the dwarf nova Z Cha during the 1987 April superoutburst and IUE-Exosat observations during the 1985 July superoutburst are presented. The UV light curve shows two dips when folded on the orbital period. One dip, at orbital phase 0.8 becomes shallower as the superoutburst progresses and can be associated with decreasing mass transfer rate from the secondary star. The other dip, at orbital phase 0.15, appears after the development of the superhump and some days after the occurrence of the largest dip at phase 0.8. The continuum flux distribution during superoutbursts is fainter and redder than in low-inclination dwarf novae during superoutbursts. This is interpreted in terms of the extended vertical disk structure which occults the hot inner parts of the disk with the development of a 'cool' bulge on the edge of the disk at orbital phase 0.75. Details of the behaviour of the UV emission lines during eclipse and away from eclipse are discussed.

Spatial variability of dissolved phosphorous concentrations and alkaline phosphatase activity in the East China Sea

NASA Astrophysics Data System (ADS)

Liu, H.; Chang, J.; Ho, T.; Gong, G.

2010-12-01

The concentrations of dissolved inorganic phosphorus (DIP) and alkaline phosphatase activity (APA) have been determined at about 25 sampling stations in the East China Sea since 2003. The stations are mainly distributed from the Changjiang river mouth to northern Taiwan and east to the shelf break. In addition to the Changjiang discharge, we have found a specific nutrient source around a coastal site (122° 2’30’’ E, 28° 40’ N). Elevated DIP and nitrate concentrations have been constantly observed around the sampling station for 8 years, where the surface DIP concentrations are generally around 0.3 µM. The nutrient source may either originate from ground water discharge or coastal upwelling, where lower temperature has been observed in the water column around the station. In general, APA has been negatively correlated with DIP concentrations in the studies sites, with lowest APA around the high DIP station and the Changjiang river mouth.

Ultra-long-period fiber grating cascaded to a knob-taper for simultaneous measurement of strain and temperature

NASA Astrophysics Data System (ADS)

Tong, Chengguo; Chen, Xudong; Zhou, Yu; He, Jiang; Yang, Wenlei; Geng, Tao; Sun, Weimin; Yuan, Libo

2018-06-01

This study presents a simple Mach-Zehnder interferometer (MZI) to obtain the bimodal characteristics that realize simultaneous measurement of strain and temperature through cascading an ultra-long-period fiber grating and a knob-shaped taper. We obtain the multi-dip feature from the MZI, and the Dips 2 and 5 are selected from 11 interference dips. Experimental results indicated that the wavelength sensitivities of Dips 2 and 5 are - 0.54 nm mɛ-1 and 0.058 nm °C-1, and - 0.53 nm mɛ-1 and 0.055 nm °C-1 to strain and temperature, respectively. The depth sensitivities are - 3.3 dB mɛ- 1, - 0.015 dB °C-1 and -5.8 dB mɛ-1, and 0.06 dB °C-1 for Dips 2 and 5, respectively. It is concluded that the proposed structure is suitable for simultaneous strain and temperature measurements.

Hydraulic Properties of Closely Spaced Dipping Open Fractures Intersecting a Fluid-Filled Borehole Derived From Tube Wave Generation and Scattering

NASA Astrophysics Data System (ADS)

Minato, Shohei; Ghose, Ranajit; Tsuji, Takeshi; Ikeda, Michiharu; Onishi, Kozo

2017-10-01

Fluid-filled fractures and fissures often determine the pathways and volume of fluid movement. They are critically important in crustal seismology and in the exploration of geothermal and hydrocarbon reservoirs. We introduce a model for tube wave scattering and generation at dipping, parallel-wall fractures intersecting a fluid-filled borehole. A new equation reveals the interaction of tube wavefield with multiple, closely spaced fractures, showing that the fracture dip significantly affects the tube waves. Numerical modeling demonstrates the possibility of imaging these fractures using a focusing analysis. The focused traces correspond well with the known fracture density, aperture, and dip angles. Testing the method on a VSP data set obtained at a fault-damaged zone in the Median Tectonic Line, Japan, presents evidences of tube waves being generated and scattered at open fractures and thin cataclasite layers. This finding leads to a new possibility for imaging, characterizing, and monitoring in situ hydraulic properties of dipping fractures using the tube wavefield.

Ultra-long-period fiber grating cascaded to a knob-taper for simultaneous measurement of strain and temperature

NASA Astrophysics Data System (ADS)

Tong, Chengguo; Chen, Xudong; Zhou, Yu; He, Jiang; Yang, Wenlei; Geng, Tao; Sun, Weimin; Yuan, Libo

2018-03-01

This study presents a simple Mach-Zehnder interferometer (MZI) to obtain the bimodal characteristics that realize simultaneous measurement of strain and temperature through cascading an ultra-long-period fiber grating and a knob-shaped taper. We obtain the multi-dip feature from the MZI, and the Dips 2 and 5 are selected from 11 interference dips. Experimental results indicated that the wavelength sensitivities of Dips 2 and 5 are - 0.54 nm mɛ-1 and 0.058 nm °C-1, and - 0.53 nm mɛ-1 and 0.055 nm °C-1 to strain and temperature, respectively. The depth sensitivities are - 3.3 dB mɛ- 1, - 0.015 dB °C-1 and -5.8 dB mɛ-1, and 0.06 dB °C-1 for Dips 2 and 5, respectively. It is concluded that the proposed structure is suitable for simultaneous strain and temperature measurements.

Mapping 3D fault geometry in earthquakes using high-resolution topography: Examples from the 2010 El Mayor-Cucapah (Mexico) and 2013 Balochistan (Pakistan) earthquakes

NASA Astrophysics Data System (ADS)

Zhou, Yu; Walker, Richard T.; Elliott, John R.; Parsons, Barry

2016-04-01

Fault dips are usually measured from outcrops in the field or inferred through geodetic or seismological modeling. Here we apply the classic structural geology approach of calculating dip from a fault's 3-D surface trace using recent, high-resolution topography. A test study applied to the 2010 El Mayor-Cucapah earthquake shows very good agreement between our results and those previously determined from field measurements. To obtain a reliable estimate, a fault segment ≥120 m long with a topographic variation ≥15 m is suggested. We then applied this method to the 2013 Balochistan earthquake, getting dips similar to previous estimates. Our dip estimates show a switch from north to south dipping at the southern end of the main trace, which appears to be a response to local extension within a stepover. We suggest that this previously unidentified geometrical complexity may act as the endpoint of earthquake ruptures for the southern end of the Hoshab fault.

Reciprocal Regulation of ERα and ERβ Stability and Activity by Diptoindonesin G.

PubMed

Zhao, Zibo; Wang, Lu; James, Taryn; Jung, Youngeun; Kim, Ikyon; Tan, Renxiang; Hoffmann, F Michael; Xu, Wei

2015-12-17

ERβ is regarded as a "tumor suppressor" in breast cancer due to its anti-proliferative effects. However, unlike ERα, ERβ has not been developed as a therapeutic target in breast cancer due to loss of ERβ in aggressive cancers. In a small-molecule library screen for ERβ stabilizers, we identified Diptoindonesin G (Dip G), which significantly increases ERβ protein stability while decreasing ERα protein levels. Dip G enhances the transcription and anti-proliferative activities of ERβ, while attenuating the transcription and proliferative effects of ERα. Further investigation revealed that instead of targeting ER, Dip G targets the CHIP E3 ubiquitin ligase shared by ERα and ERβ. Thus, Dip G is a dual-functional moiety that reciprocally controls ERα and ERβ protein stability and activities via an indirect mechanism. The ERβ stabilization effects of Dip G may enable the development of ERβ-targeted therapies for human breast cancers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Coated Metal Articles and Method of Making

DOEpatents

Boller, Ernest R.; Eubank, Lowell D.

2004-07-06

The method of protectively coating metallic uranium which comprises dipping the metallic uranium in a molten alloy comprising about 20-75% of copper and about 80-25% of tin, dipping the coated uranium promptly into molten tin, withdrawing it from the molten tin and removing excess molten metal, thereupon dipping it into a molten metal bath comprising aluminum until it is coated with this metal, then promptly withdrawing it from the bath.

Retractable pin dual in-line package test clip

DOEpatents

Bandzuch, Gregory S.; Kosslow, William J.

1996-01-01

This invention is a Dual In-Line Package (DIP) test clip for use when troubleshooting circuits containing DIP integrated circuits. This test clip is a significant improvement over existing DIP test clips in that it has retractable pins which will permit troubleshooting without risk of accidentally shorting adjacent pins together when moving probes to different pins on energized circuits or when the probe is accidentally bumped while taking measurements.

The exploratory behaviour of rats in the hole-board apparatus: Is head-dipping a valid measure of neophilia?

PubMed Central

Brown, Gillian R.; Nemes, Christopher

2008-01-01

The exploratory behaviour of laboratory rodents is of interest within a number of areas of behavioural pharmacology. However, how best to measure exploratory behaviour in rodents remains a contentious issue. Many unconditioned tests, such as the open field, potentially confound general locomotor activity with exploration. The hole-board apparatus appears to avoid this confound, as head-dipping into holes in the floor is assumed to be a valid measure of the subject's attraction towards novelty (neophilia). This study aimed to investigate whether head-dipping should be considered a valid measure of neophilia by comparing performance of adult male and female Lister hooded rats on the hole-board task (a) over repeated sessions and (b) when novel objects were absent or present underneath the holes. The results show that head-dipping initially decreased across repeated exposures, while time spent in the aversive central area increased. No change in head-dipping was seen in response to objects being placed underneath the holes. Rather than being a measure of neophilia, these results support the hypothesis that head-dipping represents an escape response, which declines as the subject becomes less fearful. These results are compared with previous studies of repeated exposure to other novel environments. PMID:18406075

A review of terrorism and its reduction of the gender ratio at birth after seasonal adjustment.

PubMed

Grech, Victor; Zammit, Dorota

2017-12-01

Males are born in excess of females, a ratio expressed as M/T (males:total births). The ratio exhibits seasonal variation. Furthermore, acute stressful events may result in a transient dip in male births due to excess foetal losses, reducing M/T. This study was carried out in order to identify significant M/T dips after adjusting for seasonality. Live births by gender and month were sought for acute stressful events. After seasonal correction (where appropriate), M/T dips were sought. Live births. M/T dips. This paper studied 112,226,306 live births. The following events showed dips ≤5th percentile 3-5months after these acute episodes: the Brooklyn Bridge protests, Katrina Hurricane for all 4 states and for each individual state (Alabama, Florida, Louisiana, Mississippi), the Battle in Seattle, the London bombings, The Madrid bombings (for Madrid and for Spain), the Breivik shooting, the Oklahoma City bombing and the Sandy Hook Elementary School shooting. The Virginia Polytechnic Institute and State University shooting the Fukushima Daiichi nuclear disaster also showed dips albeit slightly later. Seasonal adjustments should be taken into consideration in order to avoid Type 1 or 2 error pitfalls. Copyright © 2017 Elsevier B.V. All rights reserved.

Seismic reflection profiling in the Boulder batholith, Montana

NASA Astrophysics Data System (ADS)

Vejmelek, Libor; Smithson, Scott B.

1995-09-01

Seismic reflection profiling combined with gravity data allows more exact determination of the geometry of the controversial Boulder batholith of Montana, reveals laminated structure of the lower crust beneath the batholith, and identifies the Moho at a depth of 38 km. The batholith has inward-dipping contacts, the dip being about 50° on the west side, on the basis of seismic data; and the depth to the batholith floor is constrained between 12 and 18 km, indicating a great volume for the batholith. The Boulder batholith was emplaced between 80 and 70 Ma during an eastward thrusting in the fold-and-thrust belt. A presumed basal decollement of the thrust system might coincide with the batholith floor and may correspond to the top of the lower-crustal layering at a depth of 18 km.

Slip and Dilation Tendency Anlysis of Neal Hot Springs Geothermal Area

DOE Data Explorer

Faulds, James E.

2013-12-31

Slip and Dilation Tendency in focus areas Critically stressed fault segments have a relatively high likelihood of acting as fluid flow conduits (Sibson, 1994). As such, the tendency of a fault segment to slip (slip tendency; Ts; Morris et al., 1996) or to dilate (dilation tendency; Td; Ferrill et al., 1999) provides an indication of which faults or fault segments within a geothermal system are critically stressed and therefore likely to transmit geothermal fluids. The slip tendency of a surface is defined by the ratio of shear stress to normal stress on that surface: Ts = τ / σn (Morris et al., 1996). Dilation tendency is defined by the stress acting normal to a given surface: Td = (σ1-σn) / (σ1-σ3) (Ferrill et al., 1999). Slip and dilation were calculated using 3DStress (Southwest Research Institute). Slip and dilation tendency are both unitless ratios of the resolved stresses applied to the fault plane by ambient stress conditions. Values range from a maximum of 1, a fault plane ideally oriented to slip or dilate under ambient stress conditions to zero, a fault plane with no potential to slip or dilate. Slip and dilation tendency values were calculated for each fault in the focus study areas at, McGinness Hills, Neal Hot Springs, Patua, Salt Wells, San Emidio, and Tuscarora on fault traces. As dip is not well constrained or unknown for many faults mapped in within these we made these calculations using the dip for each fault that would yield the maximum slip tendency or dilation tendency. As such, these results should be viewed as maximum tendency of each fault to slip or dilate. The resulting along-fault and fault-to-fault variation in slip or dilation potential is a proxy for along fault and fault-to-fault variation in fluid flow conduit potential. Stress Magnitudes and directions Stress field variation within each focus area was approximated based on regional published data and the world stress database (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2010; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012; Moeck et al., 2010; Moos and Ronne, 2010 and Reinecker et al., 2005) as well as local stress information if applicable. For faults within these focus systems we applied either a normal faulting stress regime where the vertical stress (sv) is larger than the maximum horizontal stress (shmax) which is larger than the minimum horizontal stress (sv>shmax>shmin) or strike-slip faulting stress regime where the maximum horizontal stress (shmax) is larger than the vertical stress (sv) which is larger than the minimum horizontal stress (shmax >sv>shmin) depending on the general tectonic province of the system. Based on visual inspection of the limited stress magnitude data in the Great Basin we used magnitudes such that shmin/shmax = .527 and shmin/sv= .46, which are consistent with complete and partial stress field determinations from Desert Peak, Coso, the Fallon area and Dixie valley (Hickman et al., 2000; Hickman et al., 1998 Robertson-Tait et al., 2004; Hickman and Davatzes, 2011; Davatzes and Hickman, 2006; Blake and Davatzes 2011; Blake and Davatzes, 2012). Based on inversion of fault kinematic data, Edwards (2013) interpreted that two discrete stress orientations are preserved at Neal Hot Springs. An older episode of east-west directed extension and a younger episode of southwest-northeast directed sinistral, oblique -normal extension. This interpretation is consistent with the evolution of Cenozoic tectonics in the region (Edwards, 2013). As such we applied a southwest-northeast (060) directed normal faulting stress regime, consistent with the younger extensional episode, to the Neal Hot Springs faults. Under these stress conditions northeast striking steeply dipping fault segments have the highest tendency to dilate and northeast striking 60° dipping fault segments have the highest tendency to slip. Under these stress condition...

Kinematic evolution of a regional-scale gravity-driven deepwater fold-and-thrust belt: The Lamu Basin case-history (East Africa)

NASA Astrophysics Data System (ADS)

Cruciani, F.; Barchi, M. R.; Koyi, H. A.; Porreca, M.

2017-08-01

The deepwater fold-and-thrust belts (DWFTBs) are geological structures recently explored thanks to advances in offshore seismic imaging by oil industry. In this study we present a kinematic analysis based on three balanced cross-sections of depth-converted, 2-D seismic profiles along the offshore Lamu Basin (East African passive margin). This margin is characterized by a regional-scale DWFTB (> 450 km long), which is the product of gravity-driven contraction on the shelf that exhibits complex structural styles and differing amount of shortening along strike. Net shortening is up to 48 km in the northern wider part of the fold-and-thrust belt (≈ 180 km), diminishing to < 15 km toward the south, where the belt is markedly narrower (≈ 50 km). The three balanced profiles show a shortening percentage around 20% (comparable with the maximum values documented in other gravity-driven DWFTBs), with a significant variability along dip: higher values are achieved in the outer (i.e. down-dip) portion of the system, dominated by basinward-verging, imbricate thrust sheets. Fold wavelength increases landward, where doubly-verging structures and symmetric detachment folds accommodate a lower amount of shortening. Similar to other cases, a linear and systematic relationship between sedimentary thickness and fold wavelength is observed. Reconstruction of the rate of shortening through time within a fold-and-thrust belt shows that after an early phase of slow activation (Late Cretaceous), > 95% of net shortening was produced in < 10 Myr (during Paleocene). During this acme phase, which followed a period of high sedimentation rate, thrusts were largely synchronous and the shortening rate reached a maximum value of 5 mm/yr. The kinematic evolution reconstructed in this study suggests that the structural evolution of gravity-driven fold-and-thrust belts differs from the accretionary wedges and the collisional fold-and-thrust belts, where thrusts propagate in-sequence and shortening is uniformly accommodated along dip.

Relationship between depression and diabetes in pregnancy: A systematic review

PubMed Central

Ross, Glynis P; Falhammar, Henrik; Chen, Roger; Barraclough, Helen; Kleivenes, Ole; Gallen, Ian

2016-01-01

AIM To systematically review the literature on women with both diabetes in pregnancy (DIP) and depression during or after pregnancy. METHODS In this systematic literature review, PubMed/MEDLINE and EMBASE were searched (13 November 2015) using terms for diabetes (type 1, type 2, or gestational), depression, and pregnancy (no language or date restrictions). Publications that reported on women who had both DIP (any type) and depression or depressive symptoms before, during, or within one year after pregnancy were considered for inclusion. All study types were eligible for inclusion; conference abstracts, narrative reviews, nonclinical letters, editorials, and commentaries were excluded, unless they provided treatment guidance. RESULTS Of 1189 articles identified, 48 articles describing women with both DIP and depression were included (sample sizes 36 to > 32 million). Overall study quality was poor; most studies were observational, and only 12 studies (mostly retrospective database studies) required clinical depression diagnosis. The prevalence of concurrent DIP (any type) and depression in general populations of pregnant women ranged from 0% to 1.6% (median 0.61%; 12 studies). The prevalence of depression among women with gestational diabetes ranged from 4.1% to 80% (median 14.7%; 16 studies). Many studies examined whether DIP was a risk factor for depression or depression was a risk factor for DIP. However, there was no clear consensus for either relationship. Importantly, we found limited guidance on the management of women with both DIP and depression. CONCLUSION Given the increasing prevalence of diabetes and depression, high-quality research and specific guidance for management of pregnant women with both conditions are warranted. PMID:27895824

dipIQ: Blind Image Quality Assessment by Learning-to-Rank Discriminable Image Pairs.

PubMed

Ma, Kede; Liu, Wentao; Liu, Tongliang; Wang, Zhou; Tao, Dacheng

2017-05-26

Objective assessment of image quality is fundamentally important in many image processing tasks. In this work, we focus on learning blind image quality assessment (BIQA) models which predict the quality of a digital image with no access to its original pristine-quality counterpart as reference. One of the biggest challenges in learning BIQA models is the conflict between the gigantic image space (which is in the dimension of the number of image pixels) and the extremely limited reliable ground truth data for training. Such data are typically collected via subjective testing, which is cumbersome, slow, and expensive. Here we first show that a vast amount of reliable training data in the form of quality-discriminable image pairs (DIP) can be obtained automatically at low cost by exploiting largescale databases with diverse image content. We then learn an opinion-unaware BIQA (OU-BIQA, meaning that no subjective opinions are used for training) model using RankNet, a pairwise learning-to-rank (L2R) algorithm, from millions of DIPs, each associated with a perceptual uncertainty level, leading to a DIP inferred quality (dipIQ) index. Extensive experiments on four benchmark IQA databases demonstrate that dipIQ outperforms state-of-the-art OU-BIQA models. The robustness of dipIQ is also significantly improved as confirmed by the group MAximum Differentiation (gMAD) competition method. Furthermore, we extend the proposed framework by learning models with ListNet (a listwise L2R algorithm) on quality-discriminable image lists (DIL). The resulting DIL Inferred Quality (dilIQ) index achieves an additional performance gain.

Beauveria bassiana (Balsamo) Vuillemin as an endophyte in tissue culture banana (Musa spp.).

PubMed

Akello, Juliet; Dubois, Thomas; Gold, Clifford S; Coyne, Daniel; Nakavuma, Jessica; Paparu, Pamela

2007-09-01

Beauveria bassiana is considered a virulent pathogen against the banana weevil Cosmopolites sordidus. However, current field application techniques for effective control against this pest remain a limitation and an alternative method for effective field application needs to be investigated. Three screenhouse experiments were conducted to determine the ability of B. bassiana to form an endophytic relationship with tissue culture banana (Musa spp.) plants and to evaluate the plants for possible harmful effects resulting from this relationship. Three Ugandan strains of B. bassiana (G41, S204 and WA) were applied by dipping the roots and rhizome in a conidial suspension, by injecting a conidial suspension into the plant rhizome and by growing the plants in sterile soil mixed with B. bassiana-colonized rice substrate. Four weeks after inoculation, plant growth parameters were determined and plant tissue colonization assessed through re-isolation of B. bassiana. All B. bassiana strains were able to colonize banana plant roots, rhizomes and pseudostem bases. Dipping plants in a conidial suspension achieved the highest colonization with no negative effect on plant growth or survival. Beauveria bassiana strain G41 was the best colonizer (up to 68%, 79% and 41% in roots, rhizome and pseudostem base, respectively) when plants were dipped. This study demonstrated that, depending on strain and inoculation method, B. bassiana can form an endophytic relationship with tissue culture banana plants, causing no harmful effects and might provide an alternative method for biological control of C. sordidus.

VizieR Online Data Catalog: Detection of Kepler multiple M-star systems (Rappaport+, 2014)

NASA Astrophysics Data System (ADS)

Rappaport, S.; Swift, J.; Levine, A.; Joss, M.; Sanchis-Ojeda, R.; Barclay, T.; Still, M.; Handler, G.; Olah, K.; Muirhead, P. S.; Huber, D.; Vida, K.

2017-07-01

In all, we find 297 of the 3897 targets exhibit the requisite significant Fourier transform (FT) signal comprising a base frequency plus its harmonic, with the base frequency exceeding 0.5 cycles/day (i.e., Prot<2 days). We believe that the majority of these periodicities are likely to be due to stellar rotation manifested via starspots, but a significant number may be due to planet transits and binary eclipses. The individual FTs for these systems were further examined to eliminate those which were clearly not due to rotating starspots. In all cases we folded the data modulo the detected fundamental period, and were readily able to rule out cases due to transiting planets since their well-known sharp, relatively rectangular dipping profiles are characteristic. Of course, we also checked the KOI list for matches. Any of the objects that appear in the Kepler eclipsing binary ("EB") star catalog (e.g., Matijevic et al. 2012AJ....143..123M) were likewise eliminated. (2 data files).

A soft biomolecule actuator based on a highly functionalized bacterial cellulose nano-fiber network with carboxylic acid groups.

PubMed

Wang, Fan; Jeon, Jin-Han; Park, Sukho; Kee, Chang-Doo; Kim, Seong-Jun; Oh, Il-Kwon

2016-01-07

Upcoming human-related applications such as soft wearable electronics, flexible haptic systems, and active bio-medical devices will require bio-friendly actuating materials. Here, we report a soft biomolecule actuator based on carboxylated bacterial cellulose (CBC), ionic liquid (IL), and poly (3,4-ethylenedioxythiophene)-poly(styrenesulfonate) ( PSS) electrodes. Soft and biocompatible polymer-IL composites were prepared via doping of CBC with ILs. The highly conductive PSS layers were deposited on both sides of the CBC-IL membranes by a dip-coating technique to yield a sandwiched actuator system. Ionic conductivity and ionic exchange capacity of the CBC membrane can be increased up to 22.8 times and 1.5 times compared with pristine bacterial cellulose (BC), respectively, resulting in 8 times large bending deformation than the pure BC actuators with metallic electrodes in an open air environment. The developed CBC-IL actuators show significant progress in the development of biocompatible and soft actuating materials with quick response, low operating voltage and comparatively large bending deformation.

Transferable residues from dog fur and plasma cholinesterase inhibition in dogs treated with a flea control dip containing chlorpyrifos.

PubMed Central

Boone, J S; Tyler, J W; Chambers, J E

2001-01-01

We studied chlorpyrifos, an insecticide present in a commercial dip for treating ectoparasites in dogs, to estimate the amount of transferable residues that children could obtain from their treated pets. Although the chlorpyrifos dip is no longer supported by the manufacturer, the methodology described herein can help determine transferable residues from other flea control insecticide formulations. Twelve dogs of different breeds and weights were dipped using the recommended guidelines with a commercial, nonprescription chlorpyrifos flea dip for 4 consecutive treatments at 3-week intervals (nonshampoo protocol) and another 12 dogs were dipped with shampooing between dips (shampoo protocol). The samples collected at 4 hr and 7, 14, and 21 days after treatment in the nonshampoo protocol averaged 971, 157, 70, and 26 microg chlorpyrifos, respectively; in the shampoo protocol the samples averaged 459, 49, 15, and 10 microg, respectively. The highest single sample was about 7,000 microg collected at 4 hr. The pretreatment specific activities in the plasma of the dogs were about 75 nmol/min/mg protein for butyrylcholinesterase (BChE), and 9 nmol/min/mg protein for acetylcholinesterase (AChE). BChE was inhibited 50-75% throughout the study, and AChE was inhibited 11-18% in the nonshampoo protocol; inhibition was not as great in the shampoo protocol. There was no correlation (p

An Examination of Upper Plate Aftershocks of the Tohoku-oki Earthquake: Are They Caused by a Long-term Change in the Dip of the Subducting Plate?

NASA Astrophysics Data System (ADS)

Oryan, B.; Buck, W. R.

2017-12-01

The Tohoku-oki earthquake was one of the strongest earthquakes ever recorded. 50-80 meters of lateral motion of the sloping seafloor resulted in a tsunami that exceeded predictions and caused one of the costliest natural disasters in history. It was also the first time extensional aftershocks were observed in the upper plate over a region as wide as 250km. Inspired by these findings, researchers found similar upper plate extensional earthquakes after reexamining seismic data from past earthquakes that had also produced large tsunamis. Such extensional aftershocks are difficult to explain in terms of standard subduction models. Most models assume that the dip of the subducting plate remains constant with time. However, geological evidence indicates that the dip angle of the subducting plate changes. We hypothesize that a reduction in the dip angle of the subducting plate can cause upper plate extensional earthquakes. This change in dip angle adds extensional bending stress to the upper plate. During an inter-seismic period, the interface is `locked' causing regional compression that prevents the release of extensional energy. Relief of compressional stresses during a megathrust event can trigger the release of the accumulated extensional energy, explaining why extensional earthquakes were observed after some megathrust events. Numerical models will be used to test our hypothesis. First, we will model long term subduction with a nearly constant dip angle. Then, we will impose a `mantle wind' to reduce the dip angle of the subducting plate. Eventually, we will model a full seismic cycle of the subduction resulting in a megathrust event. The generation of extensional earthquakes in the upper plate of our model following the megathrust event will allow us to determine whether a causal link exists between these earthquakes and a reduction in the dip angle of the subducting plate.

Phosphorus cycling in the red tide incubator region of monterey bay in response to upwelling.

PubMed

Mackey, Katherine R M; Mioni, Cécile E; Ryan, John P; Paytan, Adina

2012-01-01

This study explores the cycling of phosphorus (P) in the euphotic zone following upwelling in northeastern Monterey Bay (the Red Tide Incubator region) of coastal California, with particular emphasis on how bacteria and phytoplankton that form harmful algal blooms mediate and respond to changes in P availability. In situ measurements of nutrient concentrations, phytoplankton community composition, and cell-specific alkaline phosphatase (AP) activity (determined via enzyme-labeled fluorescence assay) were measured during three cruises. Upwelling led to a 10-fold increase in dissolved inorganic (DIP) in surface waters, reaching ∼0.5 μmol L(-1). This DIP was drawn down rapidly as upwelling relaxed over a period of 1 week. Ratios of nitrate to DIP drawdown (∼5:1, calculated as the change in nitrate divided by the change in DIP) were lower than the Redfield ratio of 16:1, suggesting that luxury P uptake was occurring as phytoplankton bloomed. Dissolved organic (DOP) remained relatively constant (∼0.3 μmol L(-1)) before and immediately following upwelling, but doubled as upwelling relaxed, likely due to phytoplankton excretion and release during grazing. This transition from a relatively high DIP:DOP ratio to lower DIP:DOP ratio was accompanied by a decline in the abundance of diatoms, which had low AP activity, toward localized, spatially heterogeneous blooms of dinoflagellates in the genera Prorocentrum, Ceratium, Dinophysis, Alexandrium, and Scrippsiella that showed high AP activity regardless of ambient DIP levels. A nutrient addition incubation experiment showed that phytoplankton growth was primarily limited by nitrate, followed by DIP and DOP, suggesting that P regulates phytoplankton physiology and competition, but is not a limiting nutrient in this region. AP activity was observed in bacteria associated with lysed cell debris and aggregates of particulate organic material, where it may serve to facilitate P regeneration, as well as affixed to the surfaces of intact phytoplankton cells, possibly indicative of close, beneficial phytoplankton-bacteria interactions.

Phosphorus Cycling in the Red Tide Incubator Region of Monterey Bay in Response to Upwelling

PubMed Central

Mackey, Katherine R. M.; Mioni, Cécile E.; Ryan, John P.; Paytan, Adina

2012-01-01

This study explores the cycling of phosphorus (P) in the euphotic zone following upwelling in northeastern Monterey Bay (the Red Tide Incubator region) of coastal California, with particular emphasis on how bacteria and phytoplankton that form harmful algal blooms mediate and respond to changes in P availability. In situ measurements of nutrient concentrations, phytoplankton community composition, and cell-specific alkaline phosphatase (AP) activity (determined via enzyme-labeled fluorescence assay) were measured during three cruises. Upwelling led to a 10-fold increase in dissolved inorganic (DIP) in surface waters, reaching ∼0.5 μmol L−1. This DIP was drawn down rapidly as upwelling relaxed over a period of 1 week. Ratios of nitrate to DIP drawdown (∼5:1, calculated as the change in nitrate divided by the change in DIP) were lower than the Redfield ratio of 16:1, suggesting that luxury P uptake was occurring as phytoplankton bloomed. Dissolved organic (DOP) remained relatively constant (∼0.3 μmol L−1) before and immediately following upwelling, but doubled as upwelling relaxed, likely due to phytoplankton excretion and release during grazing. This transition from a relatively high DIP:DOP ratio to lower DIP:DOP ratio was accompanied by a decline in the abundance of diatoms, which had low AP activity, toward localized, spatially heterogeneous blooms of dinoflagellates in the genera Prorocentrum, Ceratium, Dinophysis, Alexandrium, and Scrippsiella that showed high AP activity regardless of ambient DIP levels. A nutrient addition incubation experiment showed that phytoplankton growth was primarily limited by nitrate, followed by DIP and DOP, suggesting that P regulates phytoplankton physiology and competition, but is not a limiting nutrient in this region. AP activity was observed in bacteria associated with lysed cell debris and aggregates of particulate organic material, where it may serve to facilitate P regeneration, as well as affixed to the surfaces of intact phytoplankton cells, possibly indicative of close, beneficial phytoplankton–bacteria interactions. PMID:22347222

A nanometallic nickel-coated, glass-fibre-based structural health monitoring system for polymer composites

NASA Astrophysics Data System (ADS)

Balaji, R.; Sasikumar, M.

2017-09-01

Glass-fibre-reinforced polymer matrix composites are widely used in various industries because of their unique high strength to weight ratio. Unlike metals, strain-induced and damage states of composites are complicated to predict under real-time loading due to their anisotropic nature. With that focus, a piezoresistive nanomaterial-based structural health monitoring system for laminated polymer composites is proposed to measure the strain induced in the composite under real-time loading. Nanometallic nickel-coated glass fibres are embedded into the polymer composites to monitor the strain and damage induced in them. The nanometallic nickel is coated over the glass fibre by a dip coating technique using epoxy as the binding agent. A microcontroller-based electrical resistance measurement system is used to measure the piezoresistive variation in the coated glass fibre under real-time loading. Using the piezoresistance variation of the embedded nanometallic nickel-coated glass fibre, the real-time strain and damage induced in the composite can be correlated. The piezoresistive response of the coated glass fibre is descibed in two phases, the deformation phase and the failure phase, which clearly show the various states of strain and damage induced in the composites.

Assessment of System Frequency Support Effect of PMSG-WTG Using Torque-Limit-Based Inertial Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiao; Gao, Wenzhong; Wang, Jianhui

2017-02-16

To release the 'hidden inertia' of variable-speed wind turbines for temporary frequency support, a method of torque-limit based inertial control is proposed in this paper. This method aims to improve the frequency support capability considering the maximum torque restriction of a permanent magnet synchronous generator. The advantages of the proposed method are improved frequency nadir (FN) in the event of an under-frequency disturbance; and avoidance of over-deceleration and a second frequency dip during the inertial response. The system frequency response is different, with different slope values in the power-speed plane when the inertial response is performed. The proposed method ismore » evaluated in a modified three-machine, nine-bus system. The simulation results show that there is a trade-off between the recovery time and FN, such that a gradual slope tends to improve the FN and restrict the rate of change of frequency aggressively while causing an extension of the recovery time. These results provide insight into how to properly design such kinds of inertial control strategies for practical applications.« less

Geometry and evolution of low-angle normal faults (LANF) within a Cenozoic high-angle rift system, Thailand: Implications for sedimentology and the mechanisms of LANF development

NASA Astrophysics Data System (ADS)

Morley, Chris K.

2009-10-01

At least eight examples of large (5-35 km heave), low-angle normal faults (LANFs, 20°-30° dip) occur in the Cenozoic rift basins of Thailand and laterally pass into high-angle extensional fault systems. Three large-displacement LANFs are found in late Oligocene-Miocene onshore rift basins (Suphan Buri, Phitsanulok, and Chiang Mai basins), they have (1) developed contemporaneous with, or after the onset of, high-angle extension, (2) acted as paths for magma and associated fluids, and (3) impacted sedimentation patterns. Displacement on low-angle faults appears to be episodic, marked by onset of lacustrine conditions followed by axial progradation of deltaic systems that infilled the lakes during periods of low or no displacement. The Chiang Mai LANF is a low-angle (15°-25°), high-displacement (15-35 km heave), ESE dipping LANF immediately east of the late early Miocene Doi Inthanon and Doi Suthep metamorphic core complexes. Early Cenozoic transpressional crustal thickening followed by the northward motion of India coupled with Burma relative to east Burma and Thailand (˜40-30 Ma) caused migmatization and gneiss dome uplift in the late Oligocene of the core complex region, followed by LANF activity. LANF displacement lasted 4-6 Ma during the early Miocene and possibly transported a late Oligocene-early Miocene high-angle rift system 35 km east. Other LANFs in Thailand have lower displacements and no associated metamorphic core complexes. The three LANFs were initiated as low-angle faults, not by isostatic rotation of high-angle faults. The low-angle dips appear to follow preexisting low-angle fabrics (thrusts, shear zones, and other low-angle ductile foliations) predominantly developed during Late Paleozoic and early Paleogene episodes of thrusting and folding.

Geology of the region of Guadalajara, Mexico, and its relationships with processes of subsidence

NASA Astrophysics Data System (ADS)

Suarez-Plascencia, C.; Delgado-Argote, L. A.; Nuñez-Cornu, F. J.; Sanchez, J. J.

2008-12-01

The city of Guadalajara, Mexico, began an accelerated urban growth in early 1950. During a span of 25 years a large number of gullies were artificially filled, with the aim of incorporating new areas for urbanization, particularly in the areas north and west of the city. These gullies originally formed a complex dendritic-type system, whose evolution may be associated with faults or fracture zones whose current identification are only possible based on escarpments along the Canyon of the Rio Grande de Santiago (CRGS), north of Guadalajara. Reports of affectations documented in the 80's described subsidence in buildings and infrastructure, a process that has been continued during 2008. We present the results of work done in the CRGS, which is a tectonic erosive-depression with an average depth of 500 m and exhibits a sequence of volcanic and sedimentary deposits with rapid lateral facies changes. The stratigraphic column spans a 15 km-long section along the Matatlán-Arcediano road, and, from top to bottom contains: 1) Unconsolidated pumice and tuffs with an average thickness of 12 m; 2) basaltic lavas with average thickness of 60 m; 3) the San Gaspar ignimbrite; 4) fluvial- sedimentary deposits with a thickness of approximately 20 meters that include both sub-rounded and angular volcanic clasts, with sizes up to 0.15 m; 5) a thick sequence of ignimbrites and dacitic lavas. At a depth of 1200 m.a.s.l. in the town of Arcediano, the basal sequence is composed of dacites and andesites with interbedded pumice-rich ignimbrites with 10-20 m thickness. The Rio Grande de Santiago talweg to 1018 m.a.s.l. (apparently the base of the sequence) is formed by andesite lava. In the area of San Gaspar we identified oblique-normal left-lateral faults in lavas, with a strike 191° and a dip 89°. In the Colimilla dam, 1297 m.a.s.l., we observed normal faulting (strike 267° and dip 81°), with 20-30 m jumps with reference to a unit of tephra of 3-10 m thickness. The lavas in this site present deformation, the main shear being parallel to the Rio Verde. At the site of the San Gaspar river the faults have a strike of 285° and a dip of 83v and affect ignimbrites that overlie dacitic lavas. In the area of the Arcediano bridge the normal faulting has a strike 188v and dip of 75° in andesites, and in the pumice-rich ignimbrites a shear direction with strike of 92° and dip of 84° that is parallel to the Rio Verde. During the past two years we identified approximately 1100 cases of sinking with varying magnitude in the urban area of Guadalajara. Some of these can be grouped to form alignments that are oriented with the faults identified in the CRGS region. The process of subsidence can be controlled by structures that affect the pumice sequence laying under the city of Guadalajara, facilitating the movement of groundwater through areas of weakness, removing tuffs and pumice and creating voids that later collapse, affecting buildings and infrastructure in the city.

Evaluating the effects of post dip-treatment laser marking on resistance to feeding by subterranean termites

Treesearch

Rachel A. Arango; Bessie Woodward; Stan Lebow

2016-01-01

Dip-treatment of wood packing materials is often used instead of pressure treatment mainly because of issues relating to simplicity and cost. Packaging boxes fabricated for the United States Army are required to be dip-treated for at least one minute in an approved preservative solution prior to use. These boxes are expected to have a service life of up to 20 years in...

Parameters influencing the deposition of methylammonium lead halide iodide in hole conductor free perovskite-based solar cells

NASA Astrophysics Data System (ADS)

Cohen, Bat-El; Gamliel, Shany; Etgar, Lioz

2014-08-01

Perovskite is a promising light harvester for use in photovoltaic solar cells. In recent years, the power conversion efficiency of perovskite solar cells has been dramatically increased, making them a competitive source of renewable energy. An important parameter when designing high efficiency perovskite-based solar cells is the perovskite deposition, which must be performed to create complete coverage and optimal film thickness. This paper describes an in-depth study on two-step deposition, separating the perovskite deposition into two precursors. The effects of spin velocity, annealing temperature, dipping time, and methylammonium iodide concentration on the photovoltaic performance are studied. Observations include that current density is affected by changing the spin velocity, while the fill factor changes mainly due to the dipping time and methylammonium iodide concentration. Interestingly, the open circuit voltage is almost unaffected by these parameters. Hole conductor free perovskite solar cells are used in this work, in order to minimize other possible effects. This study provides better understanding and control over the perovskite deposition through highly efficient, low-cost perovskite-based solar cells.

Drinking with a hairy tongue: viscous entrainment by dipping hairy surfaces

NASA Astrophysics Data System (ADS)

Nasto, Alice; Brun, Pierre-Thomas; Alvarado, José; Bush, John; Hosoi, Anette

2016-11-01

Nectar-drinking bats have tongues covered with hair-like papillae, enhancing their ability to take up viscous nectar by dipping. Using a combination of model experiments and theory reminiscent of Landau-Levich-Derjaguin dip coating, we rationalize this mechanism of viscous entrainment in a hairy texture. For the model experiments, hairy surfaces are fabricated using laser cut molds and casting samples with PDMS elastomer. Modeling the liquid trapped within the texture using a Darcy-Brinkman like approach, we derive the drainage flow solution. The amount of fluid that is entrained is dependent on the viscosity of the fluid, the density of the hairs, and the dipping speed. We find that there is an optimal hair density to maximize fluid uptake.

Subduction Initiation under Unfavorable Conditions and New Fault Formation

NASA Astrophysics Data System (ADS)

Mao, X.; Gurnis, M.; May, D.

2017-12-01

How subduction initiates with unfavorable dipping lithospheric heterogeneities is an important and rarely studied topic. We build a geodynamic model starting with a vertical weak zone for the Puysegur incipient subduction zone (PISZ). A true free surface is tracked in pTatin3D, based on the Arbitrary Lagrangian Eulerian (ALE) finite element method, and is used to follow the dynamic mantle-surface interaction and topographic evolution. A simplified surface process, based on linear topography diffusion, is implemented. Density and free water content for different phase assemblages are gained by referring to precalculated 4D (temperature, pressure, rock type and total water content) phase maps using Perplex. Darcy's law is used to migrate free water, and a linear water weakening is applied to the mantle material. A new visco-elastic formulation called Elastic Viscous Stress Splitting (EVSS) method is also included. Our predictions fit the morphology of the Puysegur Trench and Ridge and the deformation history on the overriding plate. We show a new thrust fault forms and evolves into a smooth subduction interface, and the preexisting weak zone becomes a vertical fault inboard of the thrust fault during subduction initiation, which explains the two-fault system at PISZ. Our model suggests that the PISZ may not yet be self-sustaining. We propose that the Snares Trough is caused by plate coupling differences between shallower and deeper parts, the tectonic sliver between two faults experiences strong rotation, and low density materials accumulate beneath the Snares trough. Extended models show that with favorable dipping heterogeneities, no new fault forms, and subduction initiates with smaller resisting forces.

Equatorial E region electric fields at the dip equator: 2. Seasonal variabilities and effects over Brazil due to the secular variation of the magnetic equator

NASA Astrophysics Data System (ADS)

Moro, J.; Denardini, C. M.; Resende, L. C. A.; Chen, S. S.; Schuch, N. J.

2016-10-01

In this work, the seasonal dependency of the E region electric field (EEF) at the dip equator is examined. The eastward zonal (Ey) and the daytime vertical (Ez) electric fields are responsible for the overall phenomenology of the equatorial and low-latitude ionosphere, including the equatorial electrojet (EEJ) and its plasma instability. The electric field components are studied based on long-term backscatter radars soundings (348 days for both systems) collected during geomagnetic quiet days (Kp ≤ 3+), from 2001 to 2010, at the São Luís Space Observatory (SLZ), Brazil (2.33°S, 44.20°W), and at the Jicamarca Radio Observatory (JRO), Peru (11.95°S, 76.87°W). Among the results, we observe, for the first time, a seasonal difference between the EEF in these two sectors in South America based on coherent radar measurements. The EEF is more intense in summer at SLZ, in equinox at JRO, and has been highly variable with season in the Brazilian sector compared to the Peruvian sector. In addition, the secular variation on the geomagnetic field and its effect on the EEJ over Brazil resulted that as much farther away is the magnetic equator from SLZ, later more the EEJ is observed (10 h LT) and sooner it ends (16 h LT). Moreover, the time interval of type II occurrence decreased significantly after the year 2004, which is a clear indication that SLZ is no longer an equatorial station due to the secular variation of the geomagnetic field.

Crustal structure and fault geometry of the 2010 Haiti earthquake from temporary seismometer deployments

USGS Publications Warehouse

Douilly, Roby; Haase, Jennifer S.; Ellsworth, William L.; Bouin, Marie‐Paule; Calais, Eric; Symithe, Steeve J.; Armbruster, John G.; Mercier de Lépinay, Bernard; Deschamps, Anne; Mildor, Saint‐Louis; Meremonte, Mark E.; Hough, Susan E.

2013-01-01

Haiti has been the locus of a number of large and damaging historical earthquakes. The recent 12 January 2010 Mw 7.0 earthquake affected cities that were largely unprepared, which resulted in tremendous losses. It was initially assumed that the earthquake ruptured the Enriquillo Plantain Garden fault (EPGF), a major active structure in southern Haiti, known from geodetic measurements and its geomorphic expression to be capable of producing M 7 or larger earthquakes. Global Positioning Systems (GPS) and Interferometric Synthetic Aperture Radar (InSAR) data, however, showed that the event ruptured a previously unmapped fault, the Léogâne fault, a north‐dipping oblique transpressional fault located immediately north of the EPGF. Following the earthquake, several groups installed temporary seismic stations to record aftershocks, including ocean‐bottom seismometers on either side of the EPGF. We use data from the complete set of stations deployed after the event, on land and offshore, to relocate all aftershocks from 10 February to 24 June 2010, determine a 1D regional crustal velocity model, and calculate focal mechanisms. The aftershock locations from the combined dataset clearly delineate the Léogâne fault, with a geometry close to that inferred from geodetic data. Its strike and dip closely agree with the global centroid moment tensor solution of the mainshock but with a steeper dip than inferred from previous finite fault inversions. The aftershocks also delineate a structure with shallower southward dip offshore and to the west of the rupture zone, which could indicate triggered seismicity on the offshore Trois Baies reverse fault. We use first‐motion focal mechanisms to clarify the relationship of the fault geometry to the triggered aftershocks.

Optoelectronic properties and interfacial durability of CNT and ITO on boro-silicate glass and PET substrates with nano- and heterostructural aspects

NASA Astrophysics Data System (ADS)

Park, Joung-Man; Wang, Zuo-Jia; Kwon, Dong-Jun; DeVries, Lawrence

2011-02-01

Nano- and hetero-structures of carbon nanotube (CNT) and indium tin oxide (ITO) can control significantly piezoelectric and optoelectronic properties in Microelectromechanical Systems (MEMS) as sensing and actuator under cyclic loading. Optimized preparing conditions were obtained for multi-functional purpose of the specimen by obtaining the best dispersion and turbidity in the solution. Optical transmittance and electrical properties were investigated for CNT and ITO dipping and spraying coating on boro-silicate glass and polyethylene terephthalate (PET) substrates by electrical resistance measurement under cyclic loading and wettability test. Uniform dip-coating was performed using Wilhelmy plate method due to its simple and convenience. Spraying coating was applied to the specimen additionally. The change in the electrical resistance and optical properties of coated layer were mainly dependent upon the number of dip-coating, the concentration of CNT and ITO solutions, and the surface treatment condition. Electric properties of coating layers were measured using four-point probe method, and surface resistance was calculated using a dual configuration method. Optical transmittance of CNT and ITO coated PET film was also evaluated using UV spectrum. Surface energy and their hydrophilic and hydrophobic properties of CNT and ITO coated substrates were investigated by wettability test via static and dynamic contact angle measurements. As the elapsing time of cyclic loading passed, the stability of surface resistance and thus comparative interfacial adhesion between coated layer and substrates was evaluated to compare the thermodynamic work of adhesion, Wa. As dip-coating number increased, surface resistance of coated CNT decreased, whereas the transmittance decreased step-by-step due to the thicker CNT and ITO networked layer. Nano- and heterostructural effects of CNT and ITO solution on the optical and electrical effects have been studied continuously.

Characterising the range of seismogenic behaviour on detachment faults - the case of 13o20'N, Mid Atlantic Ridge.

NASA Astrophysics Data System (ADS)

Craig, T. J.; Parnell-Turner, R.

2017-12-01

Extension at slow- and intermediate-spreading mid-ocean ridges is commonly accommodated through slip on long-lived detachment faults. These curved, convex-upward faults consist of a steeply-dipping section thought to be rooted in the lower crust or upper mantle which rotates to progressively shallower dip-angles at shallower depths, resulting in a domed, sub-horizontal oceanic core complex at the seabed. Although it is accepted that detachment faults can accumulate kilometre-scale offsets over millions of years, the mechanism of slip, and their capacity to sustain the shear stresses necessary to produce large earthquakes, remains debated. In this presentation we will show a comprehensive seismological study of an active oceanic detachment fault system on the Mid-Atlantic Ridge near 13o20'N, combining the results from a local ocean-bottom seismograph deployment with waveform inversion of a series of larger, teleseismically-observed earthquakes. The coincidence of these two datasets provides a more complete characterisation of rupture on the fault, from its initial beginnings within the uppermost mantle to its exposure at the surface. Our results demonstrate that although slip on the steeply-dipping portion of detachment fault is accommodated by failure in numerous microearthquakes, the shallower-dipping section of the fault within the upper few kilometres is relatively strong, and is capable of producing large-magnitude earthquakes. Slip on the shallow portion of active detachment faults at relatively low angles may therefore account for many more large-magnitude earthquakes at mid-ocean ridges than previously thought, and suggests that the lithospheric strength at slow-spreading mid-ocean ridges may be concentrated at shallow depths.

Rupture history of the 2011 M 9 Tohoku Japan earthquake determined from strong‐motion and high‐rate GPS recordings: Subevents radiating energy in different frequency bands

USGS Publications Warehouse

Frankel, Arthur

2013-01-01

Strong‐motion records from KiK‐net and K‐NET, along with 1 sample/s Global Positioning System (GPS) records from GEONET, were analyzed to determine the location, timing, and slip of subevents of the M 9 2011 Tohoku earthquake. Timing of arrivals on stations along the coast shows that the first subevent was located closer to the coast than subevent (2), which produced the largest slip. A waveform inversion of data from 0 to 0.2 Hz indicates that the first subevent primarily ruptured down‐dip and north of the hypocenter and had an M of 8.5. The areas of this subevent that generated the low (<0.2  Hz) and high (>0.2  Hz) frequency energy are located in the same vicinity. The inversion result for the second subevent (M 9.0) has large slip on the shallow part of the fault with peak slip of about 65 m above about 25 km depth. This slip generated the tsunami. The preferred inversion has initiation of subevent 2 on the shallow portion of the fault so that rupture proceeded down‐dip and mainly to the south. Subevent 2 started about 35 s after subevent 1, which allows for the possibility of dynamic triggering from subevent 1. The slip model predicts displacements comparable to those found from ocean‐bottom transducers near the epicenter. At frequencies that most affect tall buildings (0.1–0.5 Hz), there is a strong pulse (subevent 3) in the strong‐motion records that arrives after the near‐field ramp from subevent 2. High‐frequency subevent 3 was located down‐dip and south of the high‐slip portion of subevent 2 and was initiated as rupture from subevent 2 proceeded down‐dip. The compact pulse for subevent 3 is modeled with an M 8.0 source in a 75 by 30 km area that ruptured down‐dip and to the south with a high slip velocity, indicating high stress drop.

Effect of urea inclusion in diets containing corn dried distillers grains on feedlot cattle performance, carcass characteristics, ruminal fermentation, total tract digestibility, and purine derivatives-to-creatinine index.

PubMed

Ceconi, I; Ruiz-Moreno, M J; DiLorenzo, N; DiCostanzo, A; Crawford, G I

2015-01-01

Increased availability of rapidly fermentable carbohydrates and a great proportion of corn-derived CP in the diet may result in a degradable intake protein (DIP) deficit. Therefore, ruminal DIP deficit may result from high dietary inclusion of processed corn grain and small to moderate inclusion of corn distillers grains (DG). Two experiments were conducted to evaluate the effect of increasing dietary DIP concentration through the inclusion of urea on feedlot cattle performance, carcass characteristics, ruminal fermentation, total tract digestibility, and purine derivatives-to-creatinine (PDC) index. In Exp. 1, 42 steers (428 ± 5 kg initial BW) were assigned randomly to 1 of 3 diets containing (DM basis) 0 (control [CON]), 0.4 (low urea [LU]), or 0.6% urea (high urea [HU]) to provide 6.4, 7.5, or 8.0% dietary DIP, respectively, and 12% high-moisture corn (HMC), 20% corn dried DG with solubles (DDGS), 10% ryegrass haylage, 2.9% dry supplement, and dry-rolled corn (DRC). Steers were fed ad libitum once daily using a Calan gate system. Carcass-adjusted final BW and DMI were similar among treatments (P ≥ 0.58). Carcass-adjusted ADG was greater (P ≤ 0.04) for the HU diet compared with the LU and CON diets and was similar (P = 0.73) between the LU and CON diets. Carcass-adjusted G:F was greater (P = 0.03) for the HU diet compared with the LU diet, tended (P = 0.09) to be greater compared with the CON diet, and was similar (P = 0.61) between the LU and CON diets. Carcass characteristics were similar (P ≥ 0.34) among treatments. In Exp. 2, 4 ruminally cannulated steers (347 ± 18 kg initial BW) were randomly assigned to a replicated 2 × 2 Latin square design. Steers were fed the same CON or HU diet used in Exp. 1 ad libitum once daily. Differences in the PDC index were used as indicators of differences in microbial CP synthesis. Ruminal pH, OM intake, and starch and CP digestibility were not affected by treatment (P ≥ 0.13). Digestibility of OM and NDF and ruminal concentration of ammonia-N and total VFA were greater (P ≤ 0.04) for the HU diet compared with the CON diet. The PDC index was similar (P = 0.81) between treatments at 2 h before feed delivery: 4% lower and 14% greater for the HU diet compared with the CON diet at 4 and 10 h after feed delivery, respectively (P < 0.01). These results suggest that, due to limited DIP supplied by a DRC- and HMC-based feedlot diet containing 20% DDGS, urea supplementation resulted in improved ruminal fermentation and feed digestibility, which may explain the concurrently improved cattle performance.

3-D subduction dynamics in the western Pacific: Mantle pressure, plate kinematics, and dynamic topography.

NASA Astrophysics Data System (ADS)

Holt, A. F.; Royden, L.; Becker, T. W.; Faccenna, C.

2017-12-01

While it is well established that the slab pull of negatively buoyant oceanic plates is the primary driving force of plate tectonics, the dynamic "details" of subduction have proved difficult to pin down. We use the Philippine Sea Plate region of the western Pacific as a site to explore links between kinematic observables (e.g. topography and plate motions) and the dynamics of the subduction system (e.g. mantle flow, mantle pressure). To first order, the Philippine Sea Plate can be considered to be the central plate of a double slab system containing two slabs that dip in the same direction, to the west. This subduction configuration presents the opportunity to explore subduction dynamics in a setting where two closely spaced slabs interact via subduction-induced mantle flow and stresses transmitted through the intervening plate. We use a 3-D numerical approach (e.g. Holt et al., 2017), augmented by semi-analytical models (e.g. Jagoutz et al., 2017), to develop relationships between dynamic processes and kinematic properties, including plate velocities, lithospheric stress state, slab dip angles, and topography. When combined with subduction zone observables, this allows us to isolate the first order dynamic processes that are in operation in the Philippine Sea Plate region. Our results suggest that positive pressure build-up occurs in the asthenosphere between the two slabs (Izu-Bonin-Mariana and Ryukyu-Nankai), and that this is responsible for producing much of the observed kinematic variability in the region, including the steep dip of the Pacific slab at the Izu-Bonin-Mariana trench, as compared to the flat dip of the Pacific slab north of Japan. We then extend our understanding of the role of asthenospheric pressure to examine the forces responsible for the plate kinematics and dynamic topography of the entire Western Pacific subduction margin(s). References:Holt, A. F., Royden, L. H., Becker, T. W., 2017. Geophys. J. Int., 209, 250-265Jagoutz, O., Royden, L., Holt, A. F., Becker, T. W., 2015. Nature Geo., 8, doi:10.1038/ngeo2418

A stereoscopic imaging system for laser back scatter based trajectory measurement in ballistics: part 2

NASA Astrophysics Data System (ADS)

Chalupka, Uwe; Rothe, Hendrik

2012-03-01

The progress on a laser- and stereo-camera-based trajectory measurement system that we already proposed and described in recent publications is given. The system design was extended from one to two more powerful, DSP-controllable LASER systems. Experimental results of the extended system using different projectile-/weapon combinations will be shown and discussed. Automatic processing of acquired images using common 3DIP techniques was realized. Processing steps to extract trajectory segments from images as representative for the current application will be presented. Used algorithms for backward-calculation of the projectile trajectory will be shown. Verification of produced results is done against simulated trajectories, once in terms of detection robustness and once in terms of detection accuracy. Fields of use for the current system are within the ballistic domain. The first purpose is for trajectory measurement of small and middle caliber projectiles on a shooting range. Extension to big caliber projectiles as well as an application for sniper detection is imaginable, but would require further work. Beside classical RADAR, acoustic and optical projectile detection methods, the current system represents a further projectile location method under the new class of electro-optical methods that have been evolved in recent decades and that uses 3D imaging acquisition and processing techniques.

Chandra X-ray spectroscopy of focused wind in the Cygnus X-1 system: II. The non-dip spectrum in the low/hard state – modulations with orbital phase

DOE PAGES

Miskovicova, Ivica; Hell, Natalie; Hanke, Manfred; ...

2016-05-25

Accretion onto the black hole in the system HDE 226868/Cygnus X-1 is powered by the strong line-driven stellar wind of the O-type donor star. We study the X-ray properties of the stellar wind in the hard state of Cyg X-1, as determined using data from the Chandra High Energy Transmission Gratings. Large density and temperature inhomogeneities are present in the wind, with a fraction of the wind consisting of clumps of matter with higher density and lower temperature embedded in a photoionized gas. Absorption dips observed in the light curve are believed to be caused by these clumps. This workmore » concentrates on the non-dip spectra as a function of orbital phase. The spectra show lines of H-like and He-like ions of S, Si, Na, Mg, Al, and highly ionized Fe (Fe xvii–Fe xxiv). We measure velocity shifts, column densities, and thermal broadening of the line series. The excellent quality of these five observations allows us to investigate the orbital phase-dependence of these parameters. We show that the absorber is located close to the black hole. Doppler shifted lines point at a complex wind structure in this region, while emission lines seen in some observations are from a denser medium than the absorber. Here, the observed line profiles are phase-dependent. Their shapes vary from pure, symmetric absorption at the superior conjunction to P Cygni profiles at the inferior conjunction of the black hole.« less

GenLocDip: A Generalized Program to Calculate and Visualize Local Electric Dipole Moments.

PubMed

Groß, Lynn; Herrmann, Carmen

2016-09-30

Local dipole moments (i.e., dipole moments of atomic or molecular subsystems) are essential for understanding various phenomena in nanoscience, such as solvent effects on the conductance of single molecules in break junctions or the interaction between the tip and the adsorbate in atomic force microscopy. We introduce GenLocDip, a program for calculating and visualizing local dipole moments of molecular subsystems. GenLocDip currently uses the Atoms-In-Molecules (AIM) partitioning scheme and is interfaced to various AIM programs. This enables postprocessing of a variety of electronic structure output formats including cube and wavefunction files, and, in general, output from any other code capable of writing the electron density on a three-dimensional grid. It uses a modified version of Bader's and Laidig's approach for achieving origin-independence of local dipoles by referring to internal reference points which can (but do not need to be) bond critical points (BCPs). Furthermore, the code allows the export of critical points and local dipole moments into a POVray readable input format. It is particularly designed for fragments of large systems, for which no BCPs have been calculated for computational efficiency reasons, because large interfragment distances prevent their identification, or because a local partitioning scheme different from AIM was used. The program requires only minimal user input and is written in the Fortran90 programming language. To demonstrate the capabilities of the program, examples are given for covalently and non-covalently bound systems, in particular molecular adsorbates. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.