CORFIG- CORRECTOR SURFACE DESIGN SOFTWARE

NASA Technical Reports Server (NTRS)

Dantzler, A.

1994-01-01

Corrector Surface Design Software, CORFIG, calculates the optimum figure of a corrector surface for an optical system based on real ray traces. CORFIG generates the corrector figure in the form of a spline data point table and/or a list of polynomial coefficients. The number of spline data points as well as the number of coefficients is user specified. First, the optical system's parameters (thickness, radii of curvature, etc.) are entered. CORFIG will trace the outermost axial real ray through the uncorrected system to determine approximate radial limits for all rays. Then, several real rays are traced backwards through the system from the image to the surface that originally followed the object, within these radial limits. At this first surface, the local curvature is adjusted on a small scale to direct the rays toward the object, thus removing any accumulated aberrations. For each ray traced, this adjustment will be different, so that at the end of this process the resultant surface is made up of many local curvatures. The equations that describe these local surfaces, expressed as high order polynomials, are then solved simultaneously to yield the final surface figure, from which data points are extracted. Finally, a spline table or list of polynomial coefficients is extracted from these data points. CORFIG is intended to be used in the late stages of optical design. The system's design must have at least a good paraxial foundation. Preferably, the design should be at a stage where traditional methods of Seidel aberration correction will not bring about the required image spot size specification. CORFIG will read the system parameters of such a design and calculate the optimum figure for the first surface such that all of the original parameters remain unchanged. Depending upon the system, CORFIG can reduce the RMS image spot radius by a factor of 5 to 25. The original parameters (magnification, back focal length, etc.) are maintained because all rays upon which the corrector figure is based are traced within the bounds of the original system's outermost ray. For this reason the original system must have a certain degree of integrity. CORFIG optimizes the corrector surface figure for on-axis images at a single wavelength only. However, it has been demonstrated many times that CORFIG's method also significantly improves the quality of field images and images formed from wavelengths other than the center wavelength. CORFIG is written completely in VAX FORTRAN. It has been implemented on a DEC VAX series computer under VMS with a central memory requirement of 55 K bytes. This program was developed in 1986.

Campus Demonstration Sites for Sustainable Systems and Design: Five "Creation" Stories.

ERIC Educational Resources Information Center

Jack, Kathy; Ihara, Dan, Ed.

This paper provides a summary of the development and management of five campus demonstration sites designed to create harmony with natural systems and meet current student needs without compromising the needs of future generations. Information for each campus includes an overview of the site, project origins, the proposal and design process, the…

Building 865 Hypersonic Wind Tunnel Power System Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Larry X.

2015-02-01

This report documents the characterization and analysis of a high current power supply for the building 865 Hypersonic Wind Tunnel at Sandia National Laboratories. The system described in this report became operational in 2013, replacing the original 1968 system which employed an induction voltage regulator. This analysis and testing was completed to help the parent organization understand why an updated and redesigned power system was not delivering adequate power to resistive heater elements in the HWT. This analysis led to an improved understanding of the design and operation of the revised 2013 power supply system and identifies several reasons themore » revised system failed to achieve the performance of the original power supply installation. Design modifications to improve the performance of this system are discussed.« less

Analysis and design of trial well mooring in deepwater of the South China Sea

NASA Astrophysics Data System (ADS)

Guo, Yongfeng; Ji, Shaojun; Tang, Changquan; Li, Jiansong; Zhong, Huiquan; Ian, Ong Chin Yam

2012-06-01

Mooring systems play an important role for semi-submersible rigs that drill in deepwater. A detailed analysis was carried out on the mooring of a semi-submersible rig that conducted a trial well drilling at a deepwater location in the South China Sea in 2009. The rig was 30 years old and had a shallow platform with a designed maximum operating water depth of 457 m. Following the mooring analysis, a mooring design was given that requires upgrading of the rig's original mooring system. The upgrade included several innovations, such as installing eight larger anchors, i.e. replacing the original anchors and inserting an additional 600 m of steel wires with the existing chains. All this was done to enhance the mooring capability of the rig in order for the rig to be held in position to conduct drilling at a water depth of 476 m. The overall duration of the drilling was 50 days and the upgraded mooring system proved to be efficient in achieving the goal of keeping the rig stationary while it was drilling the trial well in the South China Sea. This successful campaign demonstrates that an older semi-submersible rig can take on drilling in deep water after careful design and proper upgrading and modification to the original mooring system.

Modularization of gradient-index optical design using wavefront matching enabled optimization.

PubMed

Nagar, Jogender; Brocker, Donovan E; Campbell, Sawyer D; Easum, John A; Werner, Douglas H

2016-05-02

This paper proposes a new design paradigm which allows for a modular approach to replacing a homogeneous optical lens system with a higher-performance GRadient-INdex (GRIN) lens system using a WaveFront Matching (WFM) method. In multi-lens GRIN systems, a full-system-optimization approach can be challenging due to the large number of design variables. The proposed WFM design paradigm enables optimization of each component independently by explicitly matching the WaveFront Error (WFE) of the original homogeneous component at the exit pupil, resulting in an efficient design procedure for complex multi-lens systems.

Application of a Design Space Exploration Tool to Enhance Interleaver Generation

DTIC Science & Technology

2009-06-24

2], originally dedicated to channel coding, are being currently reused in a large set of the whole digital communication systems (e.g. equalization... originally target interface synthesis, is shown to be also suited to the interleaver design space exploration. Our design flow can take as input...slice turbo codes,” in Proc. 3rd Int. Symp. Turbo Codes, Related Topics, Brest , 2003, pp. 343–346. [11] IEEE 802.15.3a, WPAN High Rate Alternative [12

Introduction to human factors considerations in system design

NASA Technical Reports Server (NTRS)

Chapanis, A.

1983-01-01

A definition for human factors or ergonomics and its industrial and domestic application is presented. Human factors engineering, which discovers and applies information about human abilities, limitations, and other characteristics to the design of tools, machines, systems, tasks, jobs, and environments for safe, comfortable, and effective human use, is outlined. The origins of human factors and ergonomics, the philosophy of human factors, goals and objectives, systems development and design, are reviewed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dentz, Jordan; Alaigh, Kunal

Two multifamily buildings planned in Climate Zone 4 were analyzed to determine the cost, energy and performance implications of redesigning them to comply with Zero Energy Ready Home, a recognition program of the U.S. Department of Energy. Energy modeling was conducted on one representative apartment in each building using BEopt. Construction costs were obtained from the developer and subcontractors to determine savings and cost increases over ENERGY STAR. It was found that seven items would be necessary to change to comply with ZERH criteria when starting from the original design which was compliant with ENERGY STAR version 3.0. Design changesmore » were made to the exterior walls, domestic water heating system, duct protection, duct design, garage ventilation, and pest control to comply with ZERH requirements. Energy impacts of upgrading from the original design to ZERH resulted in 2 to 8% reduction in modeled source energy consumption, or 1.7 to 10.4 MMBtu per year, although the original design was already about 8% better than a design configured to minimum ENERGY STAR criteria. According to the BEopt analysis, annualized energy related costs of the ZERH design were slightly higher for the apartment and slightly lower for the townhome when compared to the original design.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Two multifamily buildings planned in Climate Zone 4 were analyzed to determine the cost, energy and performance implications of redesigning them to comply with Zero Energy Ready Home, a recognition program of the U.S. Department of Energy. Energy modeling was conducted on one representative apartment in each building using BEopt. Construction costs were obtained from the developer and subcontractors to determine savings and cost increases over ENERGY STAR. It was found that seven items would be necessary to change to comply with ZERH criteria when starting from the original design which was compliant with ENERGY STAR version 3.0. Design changesmore » were made to the exterior walls, domestic water heating system, duct protection, duct design, garage ventilation, and pest control to comply with ZERH requirements. Energy impacts of upgrading from the original design to ZERH resulted in 2 to 8 percent reduction in modeled source energy consumption, or 1.7 to 10.4 MMBtu per year, although the original design was already about 8 percent better than a design configured to minimum ENERGY STAR criteria. According to the BEopt analysis, annualized energy related costs of the ZERH design were slightly higher for the apartment and slightly lower for the townhome when compared to the original design.« less

Design and Implementation of Distributed Crawler System Based on Scrapy

NASA Astrophysics Data System (ADS)

Fan, Yuhao

2018-01-01

At present, some large-scale search engines at home and abroad only provide users with non-custom search services, and a single-machine web crawler cannot sovle the difficult task. In this paper, Through the study and research of the original Scrapy framework, the original Scrapy framework is improved by combining Scrapy and Redis, a distributed crawler system based on Web information Scrapy framework is designed and implemented, and Bloom Filter algorithm is applied to dupefilter modul to reduce memory consumption. The movie information captured from douban is stored in MongoDB, so that the data can be processed and analyzed. The results show that distributed crawler system based on Scrapy framework is more efficient and stable than the single-machine web crawler system.

Design of an optimal preview controller for linear discrete-time descriptor systems with state delay

NASA Astrophysics Data System (ADS)

Cao, Mengjuan; Liao, Fucheng

2015-04-01

In this paper, the linear discrete-time descriptor system with state delay is studied, and a design method for an optimal preview controller is proposed. First, by using the discrete lifting technique, the original system is transformed into a general descriptor system without state delay in form. Then, taking advantage of the first-order forward difference operator, we construct a descriptor augmented error system, including the state vectors of the lifted system, error vectors, and desired target signals. Rigorous mathematical proofs are given for the regularity, stabilisability, causal controllability, and causal observability of the descriptor augmented error system. Based on these, the optimal preview controller with preview feedforward compensation for the original system is obtained by using the standard optimal regulator theory of the descriptor system. The effectiveness of the proposed method is shown by numerical simulation.

Software synthesis using generic architectures

NASA Technical Reports Server (NTRS)

Bhansali, Sanjay

1993-01-01

A framework for synthesizing software systems based on abstracting software system designs and the design process is described. The result of such an abstraction process is a generic architecture and the process knowledge for customizing the architecture. The customization process knowledge is used to assist a designer in customizing the architecture as opposed to completely automating the design of systems. Our approach using an implemented example of a generic tracking architecture which was customized in two different domains is illustrated. How the designs produced using KASE compare to the original designs of the two systems, and current work and plans for extending KASE to other application areas are described.

A Study of the System Safety Concept as it Relates to the New Walter Reed Army Medical Center, Washington, DC.

DTIC Science & Technology

1978-03-31

established the safety level of the% * originally designed facility and the extent of current safety * modifications. The objectives evaluated the...Program could identify many safety hazards thus leading to design improvements. The study provided several recommendations to formalize the Systems Safety... design , construction, and proposed systems management of the new Walter Reed Army Medical Center (WRAMC), Washington, D.C., was conducted during the

77 FR 4002 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-26

... the methodological research previously included in the original System of Record Notice (SORN). This... methodological research on improving various aspects of surveys authorized by Title 13, U.S.C. 8(b), 182, and 196, such as: survey sampling frame design; sample selection algorithms; questionnaire development, design...

30 CFR 75.1107-9 - Dry chemical devices; capacity; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Many dry chemical systems were originally designed for sodium bicarbonate before all-purpose chemical (ammonium phosphate) was shown to be more effective. Sodium bicarbonate is denser than ammonium phosphate; hence, for example, a 50-pound system designed for the sodium bicarbonate will hold slightly more by...

DOBIS and NOTIS: A Contrast in Design.

ERIC Educational Resources Information Center

Juergens, Bonnie; Blake, Ruth

1987-01-01

Compares and contrasts two systems designed for library automation applications--NOTIS, which was developed in the United States, and DOBIS, which was developed in Europe. The differences in the systems are discussed in terms of the availability or absence of machine readable bibliographic sharing capacities in the countries of origin. (CLB)

New asphalt mix design system for Oklahoma department of transportation : final report.

DOT National Transportation Integrated Search

2013-03-01

Oklahoma Department of Transportation (ODOT) has been using the Superpave mix design software for several years. The original Superpave mix design software was built around Fox Database and did not meet ODOT requirements. The software currently being...

Human factors in technology replacement: a case study in interface design for a public transport monitoring system.

PubMed

Harper, J G; Fuller, R; Sweeney, D; Waldmann, T

1998-04-01

This paper describes ergonomic issues raised during a project to provide a replacement real-time bus route control system to a large public transport company. Task and system analyses highlighted several deficiencies in the original system architecture, the human-machine interfaces and the general approach to system management. The eventual live prototype replaced the existing original system for a trial evaluation period of several weeks. During this period a number of studies was conducted with the system users in order to measure any improvements the new system, with its ergonomic features, produced over the old. Importantly, the results confirmed that (a) general responsiveness and service quality were improved, and (b) users were more comfortable with the new design. We conclude with a number of caveats which we believe will be useful to any group addressing technology impact in a large organisation.

Investigation into interactive graphics data base exchange via Gerber data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parks, R.E.

1980-03-01

Data representing the same interactive grahic design vary greatly from one graphics system manufacturer to another. Therefore, translating the data into a common form to effect data base exchange is a difficult problem. This study examines the use of the Gerber language as a common data form through which design data could be exchanged between unlike systems. For this study Applicon Graphic System was used cyclically to check retention or degeneration of the data integrity when the original design was extracted/defined in the Gerber language and reentered into the AGS utilizing various Gerber Interface Programs. The various parts of thismore » study include the transferring of data not only in the 2D environment, but 2D to 3D and 3D to 2D. Even though plots of the files appear very similar, the individual data bases are very dissimilar. Programs, both present and future, that might supply needed information or design aids and characteristics would find it virtually impossible to do so from a data base lacking the sophistication and completeness of the original AGS data base. Man-machine hours required to bring the data base back to original quality would be extensive. The loss of data base integrity shown by this study was restricted to an AGS to AGS transfer. The loss could very easily be magnified if the transfer were between unlike systems. 8 figures. (RWR)« less

Cargo Movement Operations System (CMOS). Increment II System Design Document, Final

DTIC Science & Technology

1990-08-02

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SSDD-0002 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: A002-06 DATE: 08/02/90 ORIGINATOR NAME: John J. Brassil OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 272-2999 SUBSTANTIVE: X EDITORIAL: PAGE NUMBER: 35 PARA NUMBER: 4.2.1.3.1 COMMENT OR RECOMMENDED CHANGE: Add subordinate paragraphs to describe the 3-digit System Capabilities that are listed under System Administration in Appendix G. RATIONALE: Both Process Outbound Cargo

The Use of Environmental Test Facilities for Purposes Beyond Their Original Design

NASA Technical Reports Server (NTRS)

Fisher, Terry C.; Marner, W. J.

2000-01-01

Increasing demands from space flight project offices are requiring environmental testing facilities to become more versatile with increased capabilities. At the same time, maintaining a cost-effective approach to test operations has driven efforts to use these facilities for purposes beyond their original design. This paper presents an overview of the Jet Propulsion Laboratory's efforts to provide JPL's space flight projects with test facilities to meet unique test requirements and to serve the needs of selected outside customers. The large number of recent Mars Missions, including the Mars Pathfinder project, have required testing of components and systems in a Martian surface environment in facilities originally designed for deep space testing. The unique problems associated with performing these tests are discussed, along with practical solutions. Other unique test requirements are discussed including the use of space simulation chambers for testing high altitude balloon gondolas and the use of vacuum chambers for system level test firing of an ion propulsion engine.

Analytic Considerations and Design Basis for the IEEE Distribution Test Feeders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, K. P.; Mather, B. A.; Pal, B. C.

For nearly 20 years the Test Feeder Working Group of the Distribution System Analysis Subcommittee has been developing openly available distribution test feeders for use by researchers. The purpose of these test feeders is to provide models of distribution systems that reflect the wide diversity in design and their various analytic challenges. Because of their utility and accessibility, the test feeders have been used for a wide range of research, some of which has been outside the original scope of intended uses. This paper provides an overview of the existing distribution feeder models and clarifies the specific analytic challenges thatmore » they were originally designed to examine. Additionally, the paper will provide guidance on which feeders are best suited for various types of analysis. The purpose of this paper is to provide the original intent of the Working Group and to provide the information necessary so that researchers may make an informed decision on which of the test feeders are most appropriate for their work.« less

Analytic Considerations and Design Basis for the IEEE Distribution Test Feeders

DOE PAGES

Schneider, K. P.; Mather, B. A.; Pal, B. C.; ...

2017-10-10

For nearly 20 years the Test Feeder Working Group of the Distribution System Analysis Subcommittee has been developing openly available distribution test feeders for use by researchers. The purpose of these test feeders is to provide models of distribution systems that reflect the wide diversity in design and their various analytic challenges. Because of their utility and accessibility, the test feeders have been used for a wide range of research, some of which has been outside the original scope of intended uses. This paper provides an overview of the existing distribution feeder models and clarifies the specific analytic challenges thatmore » they were originally designed to examine. Additionally, the paper will provide guidance on which feeders are best suited for various types of analysis. The purpose of this paper is to provide the original intent of the Working Group and to provide the information necessary so that researchers may make an informed decision on which of the test feeders are most appropriate for their work.« less

Design criteria for payload workstation accommodations

NASA Technical Reports Server (NTRS)

Watters, H. H.; Stokes, J. W.

1975-01-01

Anticipated shuttle sortie payload man-system design criteria needs are investigated. Man-system interactions for the scientific disciplines are listed and the extent is assessed to which documented Skylab experience is expected to provide system design guidance for each of the identified interactions. Where the analysis revealed that the reduced Skylab data does not answer the anticipated needs candidate criteria, based on unreduced Skylab data, available prior research, original analysis, or related requirements derived from previous space programs, are provided.

Cargo Movement Operations System (CMOS) System Segment Design Document (Draft) Increment II

DTIC Science & Technology

1990-05-02

and are arranged in page number order. RATIONALE: N/A CMOS PMO ACCEPTS COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION...NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SSDD-0003 PROGRAM...CMOS. CMOS PMO ACCEPTS COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ 3 ORIGINATOR

Cargo Movement Operations System (CMOS) Final System Segment Design Document Increment II, (ChaNge 02)

DTIC Science & Technology

1990-11-07

present, the documents are in conflict with each other. CMOS PMO ACCEPTS COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION...NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] p ORIGINATOR CONTROL NUMBER: SSDD-0003 PROGRAM...ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [1 ORIGINATOR CONTROL NUMBER: SSDD-0005 PROGRAM OFFICE

Design of Orion Soil Impact Study using the Modern Design of Experiments

NASA Technical Reports Server (NTRS)

DeLoach, Richard

2010-01-01

Two conventional One Factor At a Time (OFAT) test matrices under consideration for an Orion Landing System subscale soil impact study are reviewed. Certain weaknesses in the designs, systemic to OFAT experiment designs generally, are identified. An alternative test matrix is proposed that is based in the Modern Design of Experiments (MDOE), which achieves certain synergies by combining the original two test matrices into one. The attendant resource savings are quantified and the impact on uncertainty is discussed.

AGARD Flight Test Instrumentation Series. Volume 19. Digital Signal Conditioning for Flight Test. (Le Traitement du Signal Numerique pour les Essais n Vol)

DTIC Science & Technology

1991-06-01

intensive systems, including the use of onboard digital computers. Topics include: measurements that are digital in origin, sampling, encoding, transmitting...Individuals charged with designing aircraft measuring systems to become better acquainted with new solutions to their requirements. This volume Is...concerned with aircraft measuring systems as related to flight test and flight research. Measure - ments that are digital in origin or that must be

Careers in Academe: The Academic Labour Market as an Eco-System

ERIC Educational Resources Information Center

Baruch, Yehuda

2013-01-01

Purpose: This paper aims to explore the contrast between stable and dynamic labour markets in academe in light of career theories that were originally developed for business environments. Design/methodology/approach: A conceptual design, offering the eco-system as a framework. Findings: It evaluates their relevance and applicability to dynamic and…

Consideration of regional variations in climatic and soil conditions in the modified triaxial design method.

DOT National Transportation Integrated Search

2008-11-01

The Texas Department of Transportation (TxDOT) uses the modified triaxial design procedure to check : pavement designs from the flexible pavement system program. Since its original development more than : 50 years ago, little modification has been ma...

Origin and destination survey results for the Orlando-Orange County Expressway Authority

DOT National Transportation Integrated Search

2000-09-01

This report describes the design, administration, and analysis of the Origin/Destination survey of users of the Orlando-Orange County Expressway System. The basic survey form consisted of a letter-sized paper with the questionnaire on one side and a ...

Design Principles and Practices for Implementation of MIL-STD-1760 in Aircraft and Stores

DTIC Science & Technology

1987-06-01

systems, a low level of interoperability is inevitable unless the designer recognizes the design risks , is aware of their causes and available means...for minimizing the risks , and organizes all phases of the weapon system development in the original design to enhance interoperability. Retrofitting...feet or more can be detected.) 105 TABLE VIII. Distrftl-dton method trade-offs. SWITCHING MAT=I FM ADVANTAGES: 1. Low techrical risk 1. Reduction in

Interpretive Research Aiming at Theory Building: Adopting and Adapting the Case Study Design

ERIC Educational Resources Information Center

Diaz Andrade, Antonio

2009-01-01

Although the advantages of case study design are widely recognised, its original positivist underlying assumptions may mislead interpretive researchers aiming at theory building. The paper discusses the limitations of the case study design for theory building and explains how grounded theory systemic process adds to the case study design. The…

Exercise of the SSM/PMAD Breadboard. [Space Station Module/Power Management And Distribution

NASA Technical Reports Server (NTRS)

Walls, Bryan

1989-01-01

The Space Station Module Power Management and Distribution (SSM/PMAD) Breadboard is a test facility designed for advanced development of space power automation. Originally designed for 20-kHz power, the system is being converted to work with direct current (dc). Power levels are on a par with those expected for a Space Station module. Some of the strengths and weaknesses of the SSM/PMAD system in design and function are examined, and the future directions foreseen for the system are outlined.

Interactive Implementation of the Optimal Systems Control Design Program (OPTSYSX) on the IBM 3033.

DTIC Science & Technology

1984-03-01

DAS A44 159 INTERACTIVE IMPLEMENTATION OF THE OPTIMAL SYSTEMS I CONTROL DESIGN PROGRAM (OPTSYSX) ON THE 1DM 3033(U NAVAL POSTGRADUATE SCHOOL MONTEREY...noesear end idswtif’r b block number) Optimal Systems Control Systems Control Control Systems 10.; ABSTRACT (Continu an reveree side ff Roe684v ad Id yI...34 by block number) .- This thesis discusses the modification of an existing Optimal Systems Control FORTRAN program (OPTSYS) originally obtained from

76 FR 4745 - Proposed Collection; Comment Request; Bank Secrecy Act Designation of Exempt Person Report...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-26

... transition from a system originally designed for collecting paper forms to a modernized IT environment for... of DOEPs under the BSA. The DOEP will be an e-filed dynamic and interactive report used by all BSA... appropriate agencies and organizations as disclosed in FinCEN's Privacy Act System of Records Notice relating...

On the Constitutive Response Characterization for Composite Materials Via Data-Driven Design Optimization

Treesearch

John G. Michopoulos; John G. Hermanson; Athanasios lliopoulos; Samuel Lambrakos; Tomonari Furukawa

2011-01-01

In the present paper we focus on demonstrating the use of design optimization for the constitutive characterization of anisotropic material systems such as polymer matrix composites, with or without damage. All approaches are based on the availability of experimental data originating from mechatronic material testing systems that can expose specimens to...

A Novel Multilevel DC - AC Converter from Green Energy Power Generators Using Step-Square Waving and PWM Technique

NASA Astrophysics Data System (ADS)

Fajingbesi, F. E.; Midi, N. S.; Khan, S.

2017-06-01

Green energy sources or renewable energy system generally utilize modular approach in their design. This sort of power sources are generally in DC form or in single cases AC. Due to high fluctuation in the natural origin of this energy (wind & solar) source they are stored as DC. DC power however are difficult to transfer over long distances hence DC to AC converters and storage system are very important in green energy system design. In this work we have designed a novel multilevel DC to AC converter that takes into account the modular design of green energy systems. A power conversion efficiency of 99% with reduced total harmonic distortion (THD) was recorded from our simulated system design.

A Function-Behavior-State Approach to Designing Human Machine Interface for Nuclear Power Plant Operators

NASA Astrophysics Data System (ADS)

Lin, Y.; Zhang, W. J.

2005-02-01

This paper presents an approach to human-machine interface design for control room operators of nuclear power plants. The first step in designing an interface for a particular application is to determine information content that needs to be displayed. The design methodology for this step is called the interface design framework (called framework ). Several frameworks have been proposed for applications at varying levels, including process plants. However, none is based on the design and manufacture of a plant system for which the interface is designed. This paper presents an interface design framework which originates from design theory and methodology for general technical systems. Specifically, the framework is based on a set of core concepts of a function-behavior-state model originally proposed by the artificial intelligence research community and widely applied in the design research community. Benefits of this new framework include the provision of a model-based fault diagnosis facility, and the seamless integration of the design (manufacture, maintenance) of plants and the design of human-machine interfaces. The missing linkage between design and operation of a plant was one of the causes of the Three Mile Island nuclear reactor incident. A simulated plant system is presented to explain how to apply this framework in designing an interface. The resulting human-machine interface is discussed; specifically, several fault diagnosis examples are elaborated to demonstrate how this interface could support operators' fault diagnosis in an unanticipated situation.

Penetrating transmission zeros in the design of robust servomechanism systems

NASA Technical Reports Server (NTRS)

Wang, S. H.; Davison, E. J.

1981-01-01

In the design of a robust servomechanism system, it is well known that the system cannot track a reference signal whose frequency coincides with the transmission zeros of the system. This paper proposes a new design method for overcoming this difficulty. The controller to be used employs a sampler and holding device with exponential decay. It is shown that the transmission zeros of the discretized system can be shifted by changing the rate of the exponential decay of the holding device. Thus, it is possible to design a robust controller for the discretized system to track any reference signal of given frequency, even if the given frequency coincides with the transmission zeros of the original continuous-time system.

Operational recovery of turbine No. 3 at Potomac Edison`s Dam No. 4 hydrogenerating facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pelczar, R.S.

1995-12-31

The Potomac Edison Dam No. 4 hydroelectric generating station is a historic, turn of the century facility located on the Potomac River near Shepherdstown, West Virginia. The station, originally constructed in 1909, employed twin horizontal Francis hydroturbine generating systems. The systems are unique in that the turbines and generators are offset 37 feet, interconnected by rope and sheaves. In May 1989 a third vertical open flume turbine generating system was added to make use of available site capacity. Both the turbine and speed increaser were the largest products developed by their respective manufacturers for a hydro turbine-generator application. This papermore » will review the subsequent operational experience which led to the original speed increaser failure on unit No. 3 and replacement of the drive system including special design considerations to the replacement speed increaser and its support structure. Specific design challenges included: (1) Designing and implementing a reliable configuration. (2) Reducing operational sound levels. (3) Minimizing harmful structure-borne vibrations which were affecting the internal rotating elements. (4) Incorporating a system brake for emergency and service purposes.« less

Battlespace Awareness: Heterogeneous Sensor Maps of Large Scale, Complex Environments

DTIC Science & Technology

2017-06-13

reference frames enable a system designer to describe the position of any sensor or platform at any point of time. This section introduces the...analysis to evaluate the quality of reconstructions created by our algorithms. CloudCompare is an open-source tool designed for this purpose [65]. In...structure of the data. The data term seeks to keep the proposed solution (u) similar to the originally observed values ( f ). A systems designer must

Cargo Movement Operations System (CMOS). Draft Software Design Document for the PC UNIX Prototype (Air Force Configuration), Increment III

DTIC Science & Technology

1991-04-21

COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ I CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDD-0002...ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS! OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDD-0003 PROGRAM OFFICE CONTROL...COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDD-0004 PROGPLAM OFFICE CONTROL NUMBER

Modeling and Simulation for Mission Operations Work System Design

NASA Technical Reports Server (NTRS)

Sierhuis, Maarten; Clancey, William J.; Seah, Chin; Trimble, Jay P.; Sims, Michael H.

2003-01-01

Work System analysis and design is complex and non-deterministic. In this paper we describe Brahms, a multiagent modeling and simulation environment for designing complex interactions in human-machine systems. Brahms was originally conceived as a business process design tool that simulates work practices, including social systems of work. We describe our modeling and simulation method for mission operations work systems design, based on a research case study in which we used Brahms to design mission operations for a proposed discovery mission to the Moon. We then describe the results of an actual method application project-the Brahms Mars Exploration Rover. Space mission operations are similar to operations of traditional organizations; we show that the application of Brahms for space mission operations design is relevant and transferable to other types of business processes in organizations.

Spacecraft design project: High temperature superconducting infrared imaging satellite

NASA Technical Reports Server (NTRS)

1991-01-01

The High Temperature Superconductor Infrared Imaging Satellite (HTSCIRIS) is designed to perform the space based infrared imaging and surveillance mission. The design of the satellite follows the black box approach. The payload is a stand alone unit, with the spacecraft bus designed to meet the requirements of the payload as listed in the statement of work. Specifications influencing the design of the spacecraft bus were originated by the Naval Research Lab. A description of the following systems is included: spacecraft configuration, orbital dynamics, radio frequency communication subsystem, electrical power system, propulsion, attitude control system, thermal control, and structural design. The issues of testing and cost analysis are also addressed. This design project was part of the course Advanced Spacecraft Design taught at the Naval Postgraduate School.

MEMS-based microprojection system with a 1.5cc optical engine

NASA Astrophysics Data System (ADS)

Kilcher, Lucio; Abelé, Nicolas

2012-03-01

Lemoptix develops next-generation of Micro-Opto-Electromechanical Systems (MOEMS)-based laser scanning and microprojection technologies and products for professional and industrial applications. Lemoptix LSCAN laser scanning micromirrors are designed to be integrated by OEM (original equipment manufacturer) customers into a number of applications such as printers and industrial sensors, enhancing performances and enabling the development of smaller, higher resolution and lower cost products. Lemoptix MVIEW, world's smallest laser microprojection systems are ideal for integration by OEMs and ODMs (original design manufacturers) into various demanding applications such as headup displays in cars or mobile devices. Embedded MVIEW modules will enable the projection of content and information directly from the device on any nearby surface, enabling users to conveniently view and share information and content without the typical limitations of physical displays.

Two degree of freedom internal model control-PID design for LFC of power systems via logarithmic approximations.

PubMed

Singh, Jay; Chattterjee, Kalyan; Vishwakarma, C B

2018-01-01

Load frequency controller has been designed for reduced order model of single area and two-area reheat hydro-thermal power system through internal model control - proportional integral derivative (IMC-PID) control techniques. The controller design method is based on two degree of freedom (2DOF) internal model control which combines with model order reduction technique. Here, in spite of taking full order system model a reduced order model has been considered for 2DOF-IMC-PID design and the designed controller is directly applied to full order system model. The Logarithmic based model order reduction technique is proposed to reduce the single and two-area high order power systems for the application of controller design.The proposed IMC-PID design of reduced order model achieves good dynamic response and robustness against load disturbance with the original high order system. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Advanced controls for light sources

NASA Astrophysics Data System (ADS)

Biedron, S. G.; Edelen, A. L.; Milton, S. V.

2016-09-01

We present a summary of our team's recent efforts in developing adaptive, artificial intelligence-inspired techniques specifically to address several control challenges that arise in machines/systems including those in particle accelerator systems. These techniques can readily be adapted to other systems such as lasers, beamline optics, etc… We are not at all suggesting that we create an autonomous system, but create a system with an intelligent control system, that can continually use operational data to improve itself and combines both traditional and advanced techniques. We believe that the system performance and reliability can be increased based on our findings. Another related point is that the controls sub-system of an overall system is usually not the heart of the system architecture or design process. More bluntly, often times all of the peripheral systems are considered as secondary to the main system components in the architecture design process because it is assumed that the controls system will be able to "fix" challenges found later with the sub-systems for overall system operation. We will show that this is not always the case and that it took an intelligent control application to overcome a sub-system's challenges. We will provide a recent example of such a "fix" with a standard controller and with an artificial intelligence-inspired controller. A final related point to be covered is that of system adaptation for requirements not original to a system's original design.

Interface of the transport systems research vehicle monochrome display system to the digital autonomous terminal access communication data bus

NASA Technical Reports Server (NTRS)

Easley, W. C.; Tanguy, J. S.

1986-01-01

An upgrade of the transport systems research vehicle (TSRV) experimental flight system retained the original monochrome display system. The original host computer was replaced with a Norden 11/70, a new digital autonomous terminal access communication (DATAC) data bus was installed for data transfer between display system and host, while a new data interface method was required. The new display data interface uses four split phase bipolar (SPBP) serial busses. The DATAC bus uses a shared interface ram (SIR) for intermediate storage of its data transfer. A display interface unit (DIU) was designed and configured to read from and write to the SIR to properly convert the data from parallel to SPBP serial and vice versa. It is found that separation of data for use by each SPBP bus and synchronization of data tranfer throughout the entire experimental flight system are major problems which require solution in DIU design. The techniques used to accomplish these new data interface requirements are described.

Assessment of the Seattle Smart Traveler evaluation

DOT National Transportation Integrated Search

1999-09-01

The system was designed using a World Wide Web or Internet interface. Two of the unique features of the design were accommodating the desired travel times and identifying origins and destinations. A search structure was developed using a series of pu...

Design of agricultural product quality safety retrospective supervision system of Jiangsu province

NASA Astrophysics Data System (ADS)

Wang, Kun

2017-08-01

In store and supermarkets to consumers can trace back agricultural products through the electronic province card to query their origin, planting, processing, packaging, testing and other important information and found that the problems. Quality and safety issues can identify the responsibility of the problem. This paper designs a retroactive supervision system for the quality and safety of agricultural products in Jiangsu Province. Based on the analysis of agricultural production and business process, the goal of Jiangsu agricultural product quality safety traceability system construction is established, and the specific functional requirements and non-functioning requirements of the retroactive system are analyzed, and the target is specified for the specific construction of the retroactive system. The design of the quality and safety traceability system in Jiangsu province contains the design of the overall design, the trace code design and the system function module.

Design of short-range terahertz wave passive detecting system

NASA Astrophysics Data System (ADS)

Zhang, Chao; Lou, Guowei; Zhu, Li; Qian, Songsong; Li, Ting

2016-09-01

Based on the study of radiation and transmission characteristics on THz waveband, a short-range passive detecting system is designed. The scheme originated from microwave passive detecting system. A prototype was developed following the design of key components including antennas and a harmonic mixer. The system operated at 0.36 THz. A dual-beam Cassegrain antenna was adopted for receiving signals which radiated by object and background. Local oscillator signal was generated by frequency multiplication. Harmonic mixing is adopted for reducing local oscillator signal frequency required by half. Superheterodyne technology is employed for signal acquisition. The system implemented easily. Tests and measurements were taken, which showed that the scheme was feasible and the performance of the prototype system met the design requirements.

Reweighting of the primary sampling units in the National Automotive Sampling System

DOT National Transportation Integrated Search

1997-09-01

The original design of hte National Automotive Sampling System - formerly the National Accident Sampling System - called for 75 PSUs randomly selected from PSUs which were grouped into various strata across the U.S. The implementation of the PSU samp...

AN IMPROVEMENT TO THE MOUSE COMPUTERIZED UNCERTAINTY ANALYSIS SYSTEM

EPA Science Inventory

The original MOUSE (Modular Oriented Uncertainty System) system was designed to deal with the problem of uncertainties in Environmental engineering calculations, such as a set of engineering cast or risk analysis equations. It was especially intended for use by individuals with l...

Design and evaluation of a wing with embedded payloads for Small Unmanned Aerial System (SUAS) applications

NASA Astrophysics Data System (ADS)

Pearson, Roger A.

Rapidly advancing technology has developed multiple thin filmed devices capable of expanding the abilities of Small Unmanned Aircraft Systems (SUAS). This research develops a viable solution for integrating thin film solar cells into a currently operational SUAS. A wing was designed and produced that was capable of replacing the existing wing while providing additional functionality with embedded solar arrays. The study investigates the challenges of meeting the original requirements of the original equipment manufacturer wing while adapting it to fully protect and support structurally embedded payloads. In total, seven complete wings were produced and tested. Combinations of functional and simulated payloads were fully integrated into two of these wings. The merits of these designs were quantified and validated through both ground testing and flight testing with the SUAS.

Automation of On-Board Flightpath Management

NASA Technical Reports Server (NTRS)

Erzberger, H.

1981-01-01

The status of concepts and techniques for the design of onboard flight path management systems is reviewed. Such systems are designed to increase flight efficiency and safety by automating the optimization of flight procedures onboard aircraft. After a brief review of the origins and functions of such systems, two complementary methods are described for attacking the key design problem, namely, the synthesis of efficient trajectories. One method optimizes en route, the other optimizes terminal area flight; both methods are rooted in optimal control theory. Simulation and flight test results are reviewed to illustrate the potential of these systems for fuel and cost savings.

Modification of the azimuth control system in the LLMC

NASA Astrophysics Data System (ADS)

Li, Binhua; Yang, Lei; Chen, Linfei; Mao, Wei

2000-10-01

A new control system of the azimuth transmission mechanism used in the Lower Latitude Meridian Circle (LLMC) is described in this paper. Because the original azimuth transmission mechanism causes too much vibration during the transposition of the horizontal axis of the instrument, we decided to modify the original system by two ways. One is to modify the lift mechanism and the azimuth transmission mechanism. The other is to replace the original stepper motors with a new type of stepper motor. According to the requirement of the new motor and its sine subdivided microstep driver, the original control system has been modified. The new system has an expansion output board and a new control program compared with the original one. The hardware architecture of the new system is described. The program in the single chip microcontroller is written in ASM, which is composed of 10 subroutines. The program in a host PC is written in C++. The methods using in controlling motors and skills in designing these programs are discussed. Two sketch flow charts of the control program are presented in the paper. Modification of the lift mechanism is also introduced. All this works make the vibration very slight.

Full-Scale Instrumented Evaluations of Multiple Airfield Matting Systems on Soft Soil to Characterize Permanent Deformation

DTIC Science & Technology

2016-06-01

Development of a new design methodology for structural airfield mats. International Journal of Pavement Research and Tech- nology 3(3):102-109...load exerted by aircraft over a larger area. Six airfield matting systems of varying materials and designs were evaluated through the construction...position unless so designated by other authorized documents. DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO THE ORIGINATOR. ERDC/GSL

Improved Traceability of a Small Satellite Mission Concept to Requirements Using Model Based System Engineering

NASA Technical Reports Server (NTRS)

Reil, Robin L.

2014-01-01

Model Based Systems Engineering (MBSE) has recently been gaining significant support as a means to improve the "traditional" document-based systems engineering (DBSE) approach to engineering complex systems. In the spacecraft design domain, there are many perceived and propose benefits of an MBSE approach, but little analysis has been presented to determine the tangible benefits of such an approach (e.g. time and cost saved, increased product quality). This paper presents direct examples of how developing a small satellite system model can improve traceability of the mission concept to its requirements. A comparison of the processes and approaches for MBSE and DBSE is made using the NASA Ames Research Center SporeSat CubeSat mission as a case study. A model of the SporeSat mission is built using the Systems Modeling Language standard and No Magic's MagicDraw modeling tool. The model incorporates mission concept and requirement information from the mission's original DBSE design efforts. Active dependency relationships are modeled to demonstrate the completeness and consistency of the requirements to the mission concept. Anecdotal information and process-duration metrics are presented for both the MBSE and original DBSE design efforts of SporeSat.

Improved Traceability of Mission Concept to Requirements Using Model Based Systems Engineering

NASA Technical Reports Server (NTRS)

Reil, Robin

2014-01-01

Model Based Systems Engineering (MBSE) has recently been gaining significant support as a means to improve the traditional document-based systems engineering (DBSE) approach to engineering complex systems. In the spacecraft design domain, there are many perceived and propose benefits of an MBSE approach, but little analysis has been presented to determine the tangible benefits of such an approach (e.g. time and cost saved, increased product quality). This thesis presents direct examples of how developing a small satellite system model can improve traceability of the mission concept to its requirements. A comparison of the processes and approaches for MBSE and DBSE is made using the NASA Ames Research Center SporeSat CubeSat mission as a case study. A model of the SporeSat mission is built using the Systems Modeling Language standard and No Magics MagicDraw modeling tool. The model incorporates mission concept and requirement information from the missions original DBSE design efforts. Active dependency relationships are modeled to analyze the completeness and consistency of the requirements to the mission concept. Overall experience and methodology are presented for both the MBSE and original DBSE design efforts of SporeSat.

North Seattle advanced traffic management system (NSATMS) project evaluation

DOT National Transportation Integrated Search

2002-12-01

This report documents the findings of the evaluation of the North Seattle Advanced Traffic Management System (NSATMS) Project. The evaluation was originally designed to analyze the potential transportation benefits and costs of a regional arterial tr...

Design Factors for Applying Cryogen Storage and Delivery Technology to Solar Thermal Propulsion

NASA Technical Reports Server (NTRS)

Millis, Marc G.

1996-01-01

Thermodynamic Vent System (TVS) and Multilayer Insulation (MLI) technology, originally developed for long term storage of cryogen propellants in microgravity, is ideally suited for propellant storage and delivery systems for solar thermal propulsion. With this technology the heat-induced pressure rise in the tank provides the propellant delivery pressure without the need for an auxiliary pressurant system, and propellant delivery is used to remove the excess heat to control tank pressure. The factors to consider in designing such a balanced system, are presented. An example of a minimum system design is presented along with examples of laboratory-tested hardware.

Calibration and Initialization of the NPS Modified Infrared Search and Target Designation (IRSTD) System.

DTIC Science & Technology

1987-12-01

level of performance comparable to the original ADM configuration. ’p, OTIC CPY Acesion For NTiS CRA&I UTNY’ TAB [ arinc ,:,cced 0 C yfi.’ hb .vC.Je i...levels below standard. This modified system was found to be operating at a level of performance comparable to the original ADM configuration. 4’ TABLE OF...requirements for systems that function under conditions of emissions control (EMCON). The AN/SAR-8, currently in the Engineering Development Phase , is an

Automation of Design Engineering Processes

NASA Technical Reports Server (NTRS)

Torrey, Glenn; Sawasky, Gerald; Courey, Karim

2004-01-01

A method, and a computer program that helps to implement the method, have been developed to automate and systematize the retention and retrieval of all the written records generated during the process of designing a complex engineering system. It cannot be emphasized strongly enough that all the written records as used here is meant to be taken literally: it signifies not only final drawings and final engineering calculations but also such ancillary documents as minutes of meetings, memoranda, requests for design changes, approval and review documents, and reports of tests. One important purpose served by the method is to make the records readily available to all involved users via their computer workstations from one computer archive while eliminating the need for voluminous paper files stored in different places. Another important purpose served by the method is to facilitate the work of engineers who are charged with sustaining the system and were not involved in the original design decisions. The method helps the sustaining engineers to retrieve information that enables them to retrace the reasoning that led to the original design decisions, thereby helping them to understand the system better and to make informed engineering choices pertaining to maintenance and/or modifications of the system. The software used to implement the method is written in Microsoft Access. All of the documents pertaining to the design of a given system are stored in one relational database in such a manner that they can be related to each other via a single tracking number.

Robust ADP Design for Continuous-Time Nonlinear Systems With Output Constraints.

PubMed

Fan, Bo; Yang, Qinmin; Tang, Xiaoyu; Sun, Youxian

2018-06-01

In this paper, a novel robust adaptive dynamic programming (RADP)-based control strategy is presented for the optimal control of a class of output-constrained continuous-time unknown nonlinear systems. Our contribution includes a step forward beyond the usual optimal control result to show that the output of the plant is always within user-defined bounds. To achieve the new results, an error transformation technique is first established to generate an equivalent nonlinear system, whose asymptotic stability guarantees both the asymptotic stability and the satisfaction of the output restriction of the original system. Furthermore, RADP algorithms are developed to solve the transformed nonlinear optimal control problem with completely unknown dynamics as well as a robust design to guarantee the stability of the closed-loop systems in the presence of unavailable internal dynamic state. Via small-gain theorem, asymptotic stability of the original and transformed nonlinear system is theoretically guaranteed. Finally, comparison results demonstrate the merits of the proposed control policy.

Design of illumination system in ring field capsule endoscope

NASA Astrophysics Data System (ADS)

Jeng, Wei-De; Mang, Ou-Yang; Chen, Yu-Ta; Wu, Ying-Yi

2011-03-01

This paper is researching about the illumination system in ring field capsule endoscope. It is difficult to obtain the uniform illumination on the observed object because the light intensity of LED will be changed along its angular displacement and same as luminous intensity distribution curve. So we use the optical design software which is Advanced Systems Analysis Program (ASAP) to build a photometric model for the optimal design of LED illumination system in ring field capsule endoscope. In this paper, the optimal design of illumination uniformity in the ring field capsule endoscope is from origin 0.128 up to optimum 0.603 and it would advance the image quality of ring field capsule endoscope greatly.

Improving the uniformity of luminous system in radial imaging capsule endoscope system

NASA Astrophysics Data System (ADS)

Ou-Yang, Mang; Jeng, Wei-De

2013-02-01

This study concerns the illumination system in a radial imaging capsule endoscope (RICE). Uniformly illuminating the object is difficult because the intensity of the light from the light emitting diodes (LEDs) varies with angular displacement. When light is emitted from the surface of the LED, it first encounters the cone mirror, from which it is reflected, before directly passing through the lenses and complementary metal oxide semiconductor (CMOS) sensor. The light that is strongly reflected from the transparent view window (TVW) propagates again to the cone mirror, to be reflected and to pass through the lenses and CMOS sensor. The above two phenomena cause overblooming on the image plane. Overblooming causes nonuniform illumination on the image plane and consequently reduced image quality. In this work, optical design software was utilized to construct a photometric model for the optimal design of the LED illumination system. Based on the original RICE model, this paper proposes an optimal design to improve the uniformity of the illumination. The illumination uniformity in the RICE is increased from its original value of 0.128 to 0.69, greatly improving light uniformity.

T and D-Bench--Innovative Combined Support for Education and Research in Computer Architecture and Embedded Systems

ERIC Educational Resources Information Center

Soares, S. N.; Wagner, F. R.

2011-01-01

Teaching and Design Workbench (T&D-Bench) is a framework aimed at education and research in the areas of computer architecture and embedded systems. It includes a set of features not found in other educational environments. This set of features is the result of an original combination of design requirements for T&D-Bench: that the…

Making intelligent systems team players: Additional case studies

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Schreckenghost, Debra L.; Rhoads, Ron W.

1993-01-01

Observations from a case study of intelligent systems are reported as part of a multi-year interdisciplinary effort to provide guidance and assistance for designers of intelligent systems and their user interfaces. A series of studies were conducted to investigate issues in designing intelligent fault management systems in aerospace applications for effective human-computer interaction. The results of the initial study are documented in two NASA technical memoranda: TM 104738 Making Intelligent Systems Team Players: Case Studies and Design Issues, Volumes 1 and 2; and TM 104751, Making Intelligent Systems Team Players: Overview for Designers. The objective of this additional study was to broaden the investigation of human-computer interaction design issues beyond the focus on monitoring and fault detection in the initial study. The results of this second study are documented which is intended as a supplement to the original design guidance documents. These results should be of interest to designers of intelligent systems for use in real-time operations, and to researchers in the areas of human-computer interaction and artificial intelligence.

Two controller design approaches for decentralized systems

NASA Technical Reports Server (NTRS)

Ozguner, U.; Khorrami, F.; Iftar, A.

1988-01-01

Two different philosophies for designing the controllers of decentralized systems are considered within a quadratic regulator framework which is generalized to admit decentralized frequency weighting. In the first approach, the total system model is examined, and the feedback strategy for each channel or subsystem is determined. In the second approach, separate, possibly overlapping, and uncoupled models are analyzed for each channel, and the results can be combined to study the original system. The two methods are applied to the example of a model of the NASA COFS Mast Flight System.

Real-time operating system for a multi-laser/multi-detector system

NASA Technical Reports Server (NTRS)

Coles, G.

1980-01-01

The laser-one hazard detector system, used on the Rensselaer Mars rover, is reviewed briefly with respect to the hardware subsystems, the operation, and the results obtained. A multidetector scanning system was designed to improve on the original system. Interactive support software was designed and programmed to implement real time control of the rover or platform with the elevation scanning mast. The formats of both the raw data and the post-run data files were selected. In addition, the interface requirements were selected and some initial hardware-software testing was completed.

Science with the James Webb Space Telescope

NASA Technical Reports Server (NTRS)

Gardner, Jonathan P.

2012-01-01

The science objectives of the James Webb Space Telescope fall into four themes. The End of the Dark Ages: First Light and Reionization theme seeks to identify the first luminous sources to form and to determine the ionization history of the universe. The Assembly of Galaxies theme seeks to determine how galaxies and the dark matter, gas, stars, metals, morphological structures, and black holes within them evolved from the epoch of reionization to the present. The Birth of Stars and Protoplanetary Systems theme seeks to unravel the birth and early evolution of stars, from infall onto dust-enshrouded protostars, to the genesis of planetary systems. The Planetary Systems and the Origins of Life theme seeks to determine the physical and chemical properties of planetary systems around nearby stars and of our own, and to investigate the potential for life in those systems. These four science themes were used to establish the design requirements for the observatory and instrumentation. Since Webb's capabilities are unique, those science themes will remain relevant through launch and operations and goals contained within these themes will continue to guide the design and implementation choices for the mission. More recently, it has also become clear that Webb will make major contributions to other areas of research, including dark energy, dark matter, active galactic nuclei, stellar populations, exoplanet characterization and Solar System objects. In this paper, we review the original four science themes and discuss how the scientific output of Webb will extend to these new areas of research. The James Webb Space Telescope was designed to meet science objectives in four themes: The End of the Dark Ages: First Light and Reionization, The Assembly of Galaxies, The Birth of Stars and Protoplanetary Systems, and Planetary Systems and the Origins of Life. More recently, it has become clear that Webb will also make major contributions to studies of dark energy, dark matter, active galactic nuclei, stellar populations, exoplanet characterization and Solar System objects. We review the original four science themes and discuss how the scientific output of Webb will extend to these new areas of research.

An inverse method for the aerodynamic design of three-dimensional aircraft engine nacelles

NASA Technical Reports Server (NTRS)

Bell, R. A.; Cedar, R. D.

1991-01-01

A fast, efficient and user friendly inverse design system for 3-D nacelles was developed. The system is a product of a 2-D inverse design method originally developed at NASA-Langley and the CFL3D analysis code which was also developed at NASA-Langley and modified for nacelle analysis. The design system uses a predictor/corrector design approach in which an analysis code is used to calculate the flow field for an initial geometry, the geometry is then modified based on the difference between the calculated and target pressures. A detailed discussion of the design method, the process of linking it to the modified CFL3D solver and its extension to 3-D is presented. This is followed by a number of examples of the use of the design system for the design of both axisymmetric and 3-D nacelles.

The Implications of Self-Reporting Systems for Maritime Domain Awareness

DTIC Science & Technology

2006-12-01

SIA), offrent des avantages significatifs comparativement à la poursuite des navires par détecteur ordinaire et que la disponibilité de l’information...reporting system for sea-going vessels that originated in Sweden in the early 1990s. It was designed primarily for safety of life at sea (SOLAS) and...report information is prone to human error and potential malicious altering and the system itself was not designed with these vulnerabilities in mind

Trends in Publications in Radiology Journals Designated as Relating to Patient-Centered Care.

PubMed

Rosenkrantz, Andrew B; Rawson, James V

2017-05-01

To assess trends in publications in radiology journals designated as dealing with patient-centered care. PubMed was searched for articles in radiology journals for which the article's record referenced patient-centered/patient-centric care. Among these, original research articles were identified and assigned major themes. Trends were assessed descriptively. A total of 115 articles in radiology journals designated as dealing with patient-centered care were identified, including 40 original research articles. The number of articles annually ranged from 0 to 4 in 2000-2008, 5 to 9 in 2010-2012, 14 to 15 in 2013-2014, and 25 in 2015. Only four radiology journals had published more than one of the original research articles. Original research articles' most common themes were: optimization of patients' access to reports and images (n=7); patients' examination experience (5); image evaluation (n=4); radiologists meeting with patients (n=4); improving patients' knowledge of imaging (n=3); examination wait times/efficiency (n=3); examination utilization/appropriateness (n=3); and IT enhancements (n=3). A total of 13 of 40 original research articles solicited opinions from patients. One study involved patients in educating trainees regarding patient-centered care. No study involved patients in system-level decisions regarding health care design and delivery. Articles dealing with patient-centered care in radiology are increasing, though they remain concentrated in a limited number of journals. Though major themes included image/report access, patient experiences, and radiologists meeting with patients, many studies dealt with less clearly patient-centric topics such as examination interpretation, while inclusion of patients in systems design was lacking. Further research in radiology is encouraged to target a broader range of ideals of patient-centered care, such as diversity, autonomy, and compassion, and to incorporate greater patient engagement. Copyright © 2016 American College of Radiology. Published by Elsevier Inc. All rights reserved.

"Changing for My Kid": Fatherhood Experiences of Mexican-Origin Teen Fathers Involved in the Justice System

ERIC Educational Resources Information Center

Parra-Cardona, Jose Ruben; Sharp, Elizabeth A.; Wampler, Richard S.

2008-01-01

A descriptive phenomenological study was conducted with six adolescent fathers of Mexican origin on juvenile probation for a variety of serious offenses. All participants successfully completed a parenting program designed especially for teen fathers. In a series of consecutive in-depth interviews, teen fathers were asked to discuss their…

Program Helps Decompose Complex Design Systems

NASA Technical Reports Server (NTRS)

Rogers, James L., Jr.; Hall, Laura E.

1995-01-01

DeMAID (Design Manager's Aid for Intelligent Decomposition) computer program is knowledge-based software system for ordering sequence of modules and identifying possible multilevel structure for design problems such as large platforms in outer space. Groups modular subsystems on basis of interactions among them. Saves considerable amount of money and time in total design process, particularly in new design problem in which order of modules has not been defined. Originally written for design problems, also applicable to problems containing modules (processes) that take inputs and generate outputs. Available in three machine versions: Macintosh written in Symantec's Think C 3.01, Sun, and SGI IRIS in C language.

A nonlinear disturbance-decoupled elevation axis controller for the Multiple Mirror Telescope

NASA Astrophysics Data System (ADS)

Clark, Dusty; Trebisky, Tom; Powell, Keith

2008-07-01

The Multiple Mirror Telescope (MMT), upgraded in 2000 to a monolithic 6.5m primary mirror from its original array of six 1.8m primary mirrors, was commissioned with axis controllers designed early in the upgrade process without regard to structural resonances or the possibility of the need for digital filtering of the control axis signal path. Post-commissioning performance issues led us to investigate replacement of the original control system with a more modern digital controller with full control over the system filters and gain paths. This work, from system identification through controller design iteration by simulation, and pre-deployment hardware-in-the-loop testing, was performed using latest-generation tools with Matlab® and Simulink®. Using Simulink's Real Time Workshop toolbox to automatically generate C source code for the controller from the Simulink diagram and a custom target build script, we were able to deploy the new controller into our existing software infrastructure running Wind River's VxWorks™real-time operating system. This paper describes the process of the controller design, including system identification data collection, with discussion of implementation of non-linear control modes and disturbance decoupling, which became necessary to obtain acceptable wind buffeting rejection.

IMMUNOLOGICAL AND HEMATOLOGICAL EFFECTS OF MICROWAVE POWER TRANSMISSION FROM A SATELLITE POWER SYSTEM (PART 1 AND PART 2)

EPA Science Inventory

Two systems for exposing mice to 2450 MHz electromagnetic fields are described. The first system was used to expose mice dorsally to circularly polarized electromagnetic fields. The second system was a minature anechoic chamber modified from the original design. Mice were exposed...

An automation of design and modelling tasks in NX Siemens environment with original software - generator module

NASA Astrophysics Data System (ADS)

Zbiciak, M.; Grabowik, C.; Janik, W.

2015-11-01

Nowadays the design constructional process is almost exclusively aided with CAD/CAE/CAM systems. It is evaluated that nearly 80% of design activities have a routine nature. These design routine tasks are highly susceptible to automation. Design automation is usually made with API tools which allow building original software responsible for adding different engineering activities. In this paper the original software worked out in order to automate engineering tasks at the stage of a product geometrical shape design is presented. The elaborated software works exclusively in NX Siemens CAD/CAM/CAE environment and was prepared in Microsoft Visual Studio with application of the .NET technology and NX SNAP library. The software functionality allows designing and modelling of spur and helicoidal involute gears. Moreover, it is possible to estimate relative manufacturing costs. With the Generator module it is possible to design and model both standard and non-standard gear wheels. The main advantage of the model generated in such a way is its better representation of an involute curve in comparison to those which are drawn in specialized standard CAD systems tools. It comes from fact that usually in CAD systems an involute curve is drawn by 3 points that respond to points located on the addendum circle, the reference diameter of a gear and the base circle respectively. In the Generator module the involute curve is drawn by 11 involute points which are located on and upper the base and the addendum circles therefore 3D gear wheels models are highly accurate. Application of the Generator module makes the modelling process very rapid so that the gear wheel modelling time is reduced to several seconds. During the conducted research the analysis of differences between standard 3 points and 11 points involutes was made. The results and conclusions drawn upon analysis are shown in details.

Non-fragile multivariable PID controller design via system augmentation

NASA Astrophysics Data System (ADS)

Liu, Jinrong; Lam, James; Shen, Mouquan; Shu, Zhan

2017-07-01

In this paper, the issue of designing non-fragile H∞ multivariable proportional-integral-derivative (PID) controllers with derivative filters is investigated. In order to obtain the controller gains, the original system is associated with an extended system such that the PID controller design can be formulated as a static output-feedback control problem. By taking the system augmentation approach, the conditions with slack matrices for solving the non-fragile H∞ multivariable PID controller gains are established. Based on the results, linear matrix inequality -based iterative algorithms are provided to compute the controller gains. Simulations are conducted to verify the effectiveness of the proposed approaches.

Space Shuttle Star Tracker Challenges

NASA Technical Reports Server (NTRS)

Herrera, Linda M.

2010-01-01

The space shuttle fleet of avionics was originally designed in the 1970's. Many of the subsystems have been upgraded and replaced, however some original hardware continues to fly. Not only fly, but has proven to be the best design available to perform its designated task. The shuttle star tracker system is currently flying as a mixture of old and new designs, each with a unique purpose to fill for the mission. Orbiter missions have tackled many varied missions in space over the years. As the orbiters began flying to the International Space Station (ISS), new challenges were discovered and overcome as new trusses and modules were added. For the star tracker subsystem, the growing ISS posed an unusual problem, bright light. With two star trackers on board, the 1970's vintage image dissector tube (IDT) star trackers track the ISS, while the new solid state design is used for dim star tracking. This presentation focuses on the challenges and solutions used to ensure star trackers can complete the shuttle missions successfully. Topics include KSC team and industry partner methods used to correct pressurized case failures and track system performance.

Microwave detection of fatigue cracks in specially prepared steel specimens.

DOT National Transportation Integrated Search

1998-01-01

In the aging highway systems the problems of fatigue-induced damage and cracking in metal structures are very severe. Many such systems are operating even beyond their design lifetime, which requires more than the originally prescribed inspection cyc...

A HW-SW Co-Designed System for the Lunar Lander Hazard Detection and Avoidance Breadboarding

NASA Astrophysics Data System (ADS)

Palomo, Pedro; Latorre, Antonio; Valle, Carlos; Gomez de Aguero, Sergio; Hagenfeldt, Miguel; Parreira, Baltazar; Lindoso, Almudena; Portela, Marta; Garcia, Mario; San Millan, Enrique; Zharikov, Yuri; Entrena, Luis

2014-08-01

This paper presents the HW-SW co-design approach followed to tackle the design of the Hazard Detection and Avoidance (HDA) system breadboarding for the Lunar Lander ESA mission, undertaken given the fact that novel GNC technologies used to promote autonomous systems demand processing capabilities that current (and forthcoming) space processors are not able to satisfy. The paper shows how the current system design has been performed in a process in which the original HDA functionally validated design has been partitioned between SW (deemed for execution in a microprocessor) and HW algorithms (to be executed in an FPGA), considering the performance requirements and resorting to a deep analysis of the algorithms in view of their adequacy to HW or SW implementation.

Breathing Easier: HVAC Specifications for Schools.

ERIC Educational Resources Information Center

Trent, C. Curtis; Trent, Warren C.

1996-01-01

A major source of indoor air contamination in schools originates within the heating, ventilating, and air-conditioning systems (HVAC), with draw-through systems being the worst offenders. Lists provisions for designing an HVAC system and a set of criteria to adhere to when planning new construction or renovations. (nine references) (MLF)

Process models as tools in forestry research and management

Treesearch

Kurt Johnsen; Lisa Samuelson; Robert Teskey; Steve McNulty; Tom Fox

2001-01-01

Forest process models are mathematical representations of biological systems that incorporate our understanding of physiological and ecological mechanisms into predictive algorithms. These models were originally designed and used for research purposes, but are being developed for use in practical forest management. Process models designed for research...

Intervisceral artery origins in patients with abdominal aortic aneurysmal disease; evidence for systemic vascular remodelling.

PubMed

Bailey, Damian M; Evans, Tom G; Thomas, Kate Gower; White, Richard D; Twine, Chistopher P; Lewis, Michael H; Williams, Ian M

2016-08-01

What is the central question of this study? To what extent focal abdominal aortic aneurysmal (AAA) disease is associated with systemic remodelling of the vascular tree remains unknown. The present study examined whether anatomical differences exist between distances of the intervisceral artery origins and AAA location/size in patients with disease compared with healthy patients. What is the main finding and its importance? Intervisceral artery distances were shown to be consistently greater in AAA patients, highlighting the systemic nature of AAA disease that extends proximally to the abdominal aorta and its branches. The anatomical description of the natural variation in visceral artery origins has implications for the design of stent grafts and planning complex open aortic surgery. The initial histopathology of abdominal aortic aneurysmal (AAA) disease is atherosclerotic, later diverting towards a distinctive dilating rather than occlusive aortic phenotype. To what extent focal AAA disease is associated with systemic remodelling of the vascular tree remains unknown. The present study examined whether anatomical differences exist between the intervisceral artery origins and AAA location/size in patients with AAA disease (AAA+) relative to those without (AAA-). Preoperative contrast-enhanced computerized tomograms were reviewed in 90 consecutive AAA+ patients scheduled for open repair who underwent an infrarenal (n = 45), suprarenal (n = 26) or supracoeliac clamp (n = 19). These were compared with 39 age-matched AAA- control patients. Craniocaudal measurements were recorded from the distal origin of the coeliac artery to the superior mesenteric artery and from the origin of the superior mesenteric artery to both renal artery origins. Serial blood samples were obtained for estimation of the glomerular filtration rate before and after surgery. Intervisceral artery origins were shown to be consistently greater in AAA+ patients (P < 0.05 versus AAA-), although unrelated to AAA diameter (P > 0.05). Postoperative renal function became progressively more impaired the more proximal the clamp placement (estimated glomerular filtration rate for supracoeliac < suprarenal < infrarenal clamps, P < 0.05). These findings highlight the systemic nature of AAA disease that extends proximally to the abdominal aorta and its branches. The anatomical description of the natural variation in visceral artery origins has implications for the design of stent grafts and planning complex open aortic surgery. © 2016 The Authors. Experimental Physiology © 2016 The Physiological Society.

CODIT

Treesearch

Walter C. Shortle

2000-01-01

CODIT is an acronym for compartmentalization of decay in trees. It is a simple model system originally designed to help forest managers understand the patterns of discoloration and decay in living trees.

High-resolution mapping, characterization, and optimization of autonomously replicating sequences in yeast

PubMed Central

Liachko, Ivan; Youngblood, Rachel A.; Keich, Uri; Dunham, Maitreya J.

2013-01-01

DNA replication origins are necessary for the duplication of genomes. In addition, plasmid-based expression systems require DNA replication origins to maintain plasmids efficiently. The yeast autonomously replicating sequence (ARS) assay has been a valuable tool in dissecting replication origin structure and function. However, the dearth of information on origins in diverse yeasts limits the availability of efficient replication origin modules to only a handful of species and restricts our understanding of origin function and evolution. To enable rapid study of origins, we have developed a sequencing-based suite of methods for comprehensively mapping and characterizing ARSs within a yeast genome. Our approach finely maps genomic inserts capable of supporting plasmid replication and uses massively parallel deep mutational scanning to define molecular determinants of ARS function with single-nucleotide resolution. In addition to providing unprecedented detail into origin structure, our data have allowed us to design short, synthetic DNA sequences that retain maximal ARS function. These methods can be readily applied to understand and modulate ARS function in diverse systems. PMID:23241746

Origins Space Telescope: Science Case and Design Reference Mission for Concept 1

NASA Astrophysics Data System (ADS)

Meixner, Margaret; Cooray, Asantha; Pope, Alexandra; Armus, Lee; Vieira, Joaquin Daniel; Milam, Stefanie N.; Melnick, Gary; Leisawitz, David; Staguhn, Johannes G.; Bergin, Edwin; Origins Space Telescope Science and Technology Definition Team

2018-01-01

The Origins Space Telescope (OST) is the mission concept for the Far-Infrared Surveyor, one of the four science and technology definition studies of NASA Headquarters for the 2020 Astronomy and Astrophysics Decadal survey. The science case for OST covers four themes: Tracing the Signature of Life and the Ingredients of Habitable Worlds; Charting the Rise of Metals, Dust and the First Galaxies, Unraveling the Co-evolution of Black Holes and Galaxies and Understanding Our Solar System in the Context of Planetary System Formation. Using a set of proposed observing programs from the community, we estimate a design reference mission for OST mission concept 1. The mission will complete significant programs in these four themes and have time for other programs from the community. Origins will enable flagship-quality general observing programs led by the astronomical community in the 2030s. We welcome you to contact the Science and Technology Definition Team (STDT) with your science needs and ideas by emailing us at ost_info@lists.ipac.caltech.edu.

Construction of an easy-to-use CRISPR-Cas9 system by patching a newly designed EXIT circuit.

PubMed

Tang, Qiang; Lou, Chunbo; Liu, Shuang-Jiang

2017-01-01

Plasmid-borne genetic editing tools, including the widely used CRISPR-Cas9 system, have greatly facilitated bacterial programming to obtain novel functionalities. However, the lack of effective post-editing plasmid elimination methods impedes follow-up genetic manipulation or application. Conventional strategies including exposure to physical and chemical treatments, or exploiting temperature-sensitive replication origins have several drawbacks (e.g., they are limited for efficiency and are time-consuming). Therefore, the demand is apparent for easy and rapid elimination of the tool plasmids from their bacterial hosts after genetic manipulation. To bridge this gap, we designed a novel EXIT circuit with the homing endonuclease, which can be exploited for rapid and efficient elimination of various plasmids with diverse replication origins. As a proof of concept, we validated the EXIT circuit in Escherichia coli by harnessing homing endonuclease I- Sce I and its cleavage site. When integrated into multiple plasmids with different origins, the EXIT circuit allowed them to be eliminated from the host cells, simultaneously. By combining the widely used plasmid-borne CRISPR-Cas9 system and the EXIT circuit, we constructed an easy-to-use CRISPR-Cas9 system that eliminated the Cas9- and the single-guide RNA (sgRNA)-encoding plasmids in one-step. Within 3 days, we successfully constructed an atrazine-degrading E. coli strain, thus further demonstrating the advantage of this new CRISPR-Cas9 system for bacterial genome editing. Our novel EXIT circuit, which exploits the homing endonuclease I- Sce I, enables plasmid(s) with different replication origins to be eliminated from their host cells rapidly and efficiently. We also developed an easy-to-use CRISPR-Cas9 system with the EXIT circuit, and this new system can be widely applied to bacterial genome editing.

A Cost Comparison of Alternative Approaches to Distance Education in Developing Countries

NASA Technical Reports Server (NTRS)

Ventre, Gerard G.; Kalu, Alex

1996-01-01

This paper presents a cost comparison of three approaches to two-way interactive distance learning systems for developing countries. Included are costs for distance learning hardware, terrestrial and satellite communication links, and designing instruction for two-way interactive courses. As part of this project, FSEC is developing a 30-hour course in photovoltaic system design that will be used in a variety of experiments using the Advanced Communications Technology Satellite (ACTS). A primary goal of the project is to develop an instructional design and delivery model that can be used for other education and training programs. Over two-thirds of the world photovoltaics market is in developing countries. One of the objectives of this NASA-sponsored project was to develop new and better energy education programs that take advantage of advances in telecommunications and computer technology. The combination of desktop video systems and the sharing of computer applications software is of special interest. Research is being performed to evaluate the effectiveness of some of these technologies as part of this project. The design of the distance learning origination and receive sites discussed in this paper were influenced by the educational community's growing interest in distance education. The following approach was used to develop comparative costs for delivering interactive distance education to developing countries: (1) Representative target locations for receive sites were chosen. The originating site was assumed to be Cocoa, Florida, where FSEC is located; (2) A range of course development costs were determined; (3) The cost of equipment for three alternative two-way interactive distance learning system configurations was determined or estimated. The types of system configurations ranged from a PC-based system that allows instructors to originate instruction from their office using desktop video and shared application software, to a high cost system that uses a electronic classroom; (4) A range of costs for both satellite and terrestrial communications was investigated; (5) The costs of equipment and operation of the alternative configurations for the origination and receive sites were determined; (6) A range of costs for several alternative delivery scenarios (i.e., a mix of live-interactive; asynchronous interactive;use of videotapes) was determined; and (7) A preferred delivery scenario, including cost estimate, was developed.

Design review - A tool for all seasons.

NASA Technical Reports Server (NTRS)

Liberman, D. S.

1972-01-01

The origins of design review are considered together with questions of definitions. The main characteristics which distinguish the concept of design review discussed from the basic master-apprentice relationship include competence, objectivity, formality, and a systematic approach. Preliminary, major, and final reviews are the steps used in the management of the design and development process in each company. It is shown that the design review is generically a systems engineering milestone review with certain unique characteristics.

A systematic FPGA acceleration design for applications based on convolutional neural networks

NASA Astrophysics Data System (ADS)

Dong, Hao; Jiang, Li; Li, Tianjian; Liang, Xiaoyao

2018-04-01

Most FPGA accelerators for convolutional neural network are designed to optimize the inner acceleration and are ignored of the optimization for the data path between the inner accelerator and the outer system. This could lead to poor performance in applications like real time video object detection. We propose a brand new systematic FPFA acceleration design to solve this problem. This design takes the data path optimization between the inner accelerator and the outer system into consideration and optimizes the data path using techniques like hardware format transformation, frame compression. It also takes fixed-point, new pipeline technique to optimize the inner accelerator. All these make the final system's performance very good, reaching about 10 times the performance comparing with the original system.

Multilayered materials based on biopolymers as drug delivery systems.

PubMed

Vilela, Carla; Figueiredo, Ana R P; Silvestre, Armando J D; Freire, Carmen S R

2017-02-01

The design of efficient therapeutic delivery devices has become a tremendously active area of research with a strong contribution from the layer-by-layer (LbL) technology. The application of this simple yet firmly established technique for the design of drug reservoirs originates a multitude of multilayered systems of tailored architecture and with a high level of control of drug administration. Areas covered: This review will focus on the most recent and original research on LbL assemblies based on biopolymers including polysaccharides, polypeptides and proteins, with potential use in drug delivery. Herein, drug reservoirs consisting of multilayered planar films and capsules will be examined with emphasis on the ones benefiting from the non-cytotoxic and biocompatible nature of biopolymers, which are suitable to load, protect and release a high payload of toxic and fragile drugs. Expert opinion: The combination of biopolymers with LbL technology has undergone extensive research, still, there is a multitude of R&D opportunities for the design of smart drug delivery systems with distinct multilayered morphologies, low immunological response, non-invasive drug release devices, as well as the design of theranostic systems combining diagnostics and therapeutic features. Further developments in terms of scaling towards mass production in the pharmaceutical industry are expected in the long-term.

Organically Grown Architectures: Creating Decentralized, Autonomous Systems by Embryomorphic Engineering

NASA Astrophysics Data System (ADS)

Doursat, René

Exploding growth growth in computational systems forces us to gradually replace rigid design and control with decentralization and autonomy. Information technologies will progress, instead, by"meta-designing" mechanisms of system self-assembly, self-regulation and evolution. Nature offers a great variety of efficient complex systems, in which numerous small elements form large-scale, adaptive patterns. The new engineering challenge is to recreate this self-organization and let it freely generate innovative designs under guidance. This article presents an original model of artificial system growth inspired by embryogenesis. A virtual organism is a lattice of cells that proliferate, migrate and self-pattern into differentiated domains. Each cell's fate is controlled by an internal gene regulatory network network. Embryomorphic engineering emphasizes hyperdistributed architectures, and their development as a prerequisite of evolutionary design.

Life support and internal thermal control system design for the Space Station Freedom

NASA Technical Reports Server (NTRS)

Humphries, R.; Mitchell, K.; Reuter, J.; Carrasquillo, R.; Beverly, B.

1991-01-01

A Review of the Space Station Freedom Environmental Control and Life Support System (ECLSS) as well as the Internal Thermal Control System (ITCS) design, including recent changes resulting from an activity to restructure the program, is provided. The development state of the original Space Station Freedom ECLSS through the restructured configuration is considered and the selection of regenerative subsystems for oxygen and water reclamation is addressed. A survey of the present ground development and verification program is given.

The design and evolution of the beta two-stage-to-orbit horizontal takeoff and landing launch system

NASA Technical Reports Server (NTRS)

Burkardt, Leo A.; Norris, Rick B.

1992-01-01

The Beta launch system was originally conceived in 1986 as a horizontal takeoff and landing, fully reusable, two-stage-to-orbit, manned launch vehicle to replace the Shuttle. It was to be capable of delivering a 50,000 lb. payload to low polar orbit. The booster propulsion system consisted of JP fueled turbojets and LH fueled ramjets mounted in pods in an over/under arrangement, and a single LOX/LH fueled SSME rocket. The second stage orbiter, which staged at Mach 8, was powered by an SSME rocket. A major goal was to develop a vehicle design consistent with near term technology. The vehicle design was completed with a GLOW of approximately 2,000,000 lbs. All design goals were met. Since then, interest has shifted to the 10,000 lbs. to low polar orbit payload class. The original Beta was down-sized to meet this payload class. The GLOW of the down-sized vehicle was approximately 1,000,000 lbs. The booster was converted to exclusively air-breathing operation. Because the booster depends on conventional air-breathing propulsion only, the staging Mach number was reduced to 5.5. The orbiter remains an SSME rocket-powered stage.

Feedback linearization of singularly perturbed systems based on canonical similarity transformations

NASA Astrophysics Data System (ADS)

Kabanov, A. A.

2018-05-01

This paper discusses the problem of feedback linearization of a singularly perturbed system in a state-dependent coefficient form. The result is based on the introduction of a canonical similarity transformation. The transformation matrix is constructed from separate blocks for fast and slow part of an original singularly perturbed system. The transformed singular perturbed system has a linear canonical form that significantly simplifies a control design problem. Proposed similarity transformation allows accomplishing linearization of the system without considering the virtual output (as it is needed for normal form method), a technique of a transition from phase coordinates of the transformed system to state variables of the original system is simpler. The application of the proposed approach is illustrated through example.

KSC-2012-5909

NASA Image and Video Library

2012-10-19

VAN HORN, Texas – Blue Origin’s New Shepard crew capsule touched down 1,630 feet from the its simulated propulsion module launch pad at the company's West Texas launch site, completing a successful test of its New Shepard crew capsule escape system. The pusher escape system was designed and developed by Blue Origin to allow crew escape in the event of an emergency during any phase of ascent for its suborbital New Shepard system. As part of an incremental development program, the results of this test will shape the design of the escape system for the company's orbital biconic-shaped Space Vehicle. The system is expected to enable full reusability of the launch vehicle, which is different from NASA's previous launch escape systems that would pull a spacecraft away from its rocket before reaching orbit. The test was part of Blue Origin's work supporting its funded Space Act Agreement with NASA during Commercial Crew Development Round 2 CCDev2). Through initiatives like CCDev2, NASA is fostering the development of a U.S. commercial crew space transportation capability with the goal of achieving safe, reliable and cost-effective access to and from the International Space Station and low-Earth orbit. After the capability is matured and available to the government and other customers, NASA could contract to purchase commercial services to meet its station crew transportation needs. For more information, visit www.nasa.gov/commercialcrew. Image credit: Blue Origin

Mechanical properties of the fiberglass prepreg system used for the National Transonic Facility replacement blade set

NASA Technical Reports Server (NTRS)

Young, Clarence P., Jr.; Wallace, John W.

1991-01-01

The results are presented of mechanical and physical properties characterization testing for the fiber glass prepreg system used to fabricate 15 of the replacement set of 25 fan blades for the National Transonic Facility. The fan blades were fabricated to be identical to the original blade set with the exception that the 7576 style E glass cloth used for the replacement set has a different surface finish than the original 7576 cloth. The 7781 E glass cloth and resin system were unchanged. The data are presented for elevated, room, and cryogenic temperatures. The results are compared with data from the original blade set and evaluated against selected structural design criteria. Test experience is described along with recommendations for future testing of these materials if required.

Hardwired Control Changes For NSTX DC Power Feeds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramakrishnan, S.

The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. The original TFTR Hardwired Control System (HCS) with electromechanical relays was used for NSTX DC Power loop control and protection during NSTX operations. As part of the NSTX Upgrade, the HCS is being changed to a PLC-based system with the same control logic. This paper gives a description ofmore » the changeover to the new PLC-based system __________________________________________________« less

Light Vehicle Preventive Maintenance.

ERIC Educational Resources Information Center

Marine Corps Inst., Washington, DC.

This correspondence course, originally developed for the Marine Corps, is designed to instruct students in the performance of preventive maintenance on motor vehicles. Instructional materials are presented in three chapters as follows: (1) Major Maintenance Areas (maintenance system, tires, batteries, cooling systems, and vehicle lubrication; (2)…

Learning Achievement Packages: Calexico Intercultural Design.

ERIC Educational Resources Information Center

Markatos, John

Two social studies units highlight the origins and structure of government and the legislative activities of the United States government in particular. The units are part of a program designed to help 12th grade and adult education social studies teachers develop bilingual curriculum materials (English and Spanish languages) related to systems of…

RESIDENTIAL BUILDING ADAPTIVE ENERGY MANAGEMENT SYSTEM (R-BAEMS) DESIGN

EPA Science Inventory

The expected outcomes from Phase I included 1) a set of guidelines for implementing R-BAEMS in residential structures from both a retrofit and original design perspective and 2) a cost and energy analysis of R-BAEMS impact on the environment. The status of each of the outcomes...

The Planning Wheel: Value Added Performance.

ERIC Educational Resources Information Center

Murk, Peter J.; Walls, Jeffrey L.

The "Planning Wheel" is an evolution of the original Systems Approach Model (SAM) that was introduced in 1986 by Murk and Galbraith. Unlike most current planning models, which are linear in design and concept, the Planning Wheel bridges the gap between linear and nonlinear processes. The "Program Planning Wheel" is designed to…

Origins Space Telescope: Telescope Design and Instrument Specifications

NASA Astrophysics Data System (ADS)

Meixner, Margaret; Carter, Ruth; Leisawitz, David; Dipirro, Mike; Flores, Anel; Staguhn, Johannes; Kellog, James; Roellig, Thomas L.; Melnick, Gary J.; Bradford, Charles; Wright, Edward L.; Zmuidzinas, Jonas; Origins Space Telescope Study Team

2017-01-01

The Origins Space Telescope (OST) is the mission concept for the Far-Infrared Surveyor, one of the four science and technology definition studies of NASA Headquarters for the 2020 Astronomy and Astrophysics Decadal survey. The renaming of the mission reflects Origins science goals that will discover and characterize the most distant galaxies, nearby galaxies and the Milky Way, exoplanets, and the outer reaches of our Solar system. This poster will show the preliminary telescope design that will be a large aperture (>8 m in diameter), cryogenically cooled telescope. We will also present the specifications for the spectrographs and imagers over a potential wavelength range of ~10 microns to 1 millimeter. We look forward to community input into this mission definition over the coming year as we work on the concept design for the mission. Origins will enable flagship-quality general observing programs led by the astronomical community in the 2030s. We welcome you to contact the Science and Technology Definition Team (STDT) with your science needs and ideas by emailing us at firsurveyor_info@lists.ipac.caltech.edu.

Design and fabrication of an energy-harvesting device using vibration absorber

NASA Astrophysics Data System (ADS)

Heidari, Hamidreza; Afifi, Arash

2017-05-01

Energy-harvesting devices collect energy that is being wasted and convert to the electrical energy. For this reason, this type of devices is considered as a convenient alternative to traditional batteries. In this paper, experimental examinations were performed to investigate the application of harvesting device for the reduction of the vibration amplitude in a vibration system and also increase the efficiency of energy-harvesting device. This study focuses on the energy-harvesting device as both producing electrical device and a vibration disabled absorber. In this regard, a motion-based energy-harvesting device is designed to produce electrical energy and also eliminate vibrations of a two joint-end beam which is located under the harmonic excitation force. Then, the governing equations of the forced motion on the main beam are derived and energy-harvesting system are simulated. In addition, the system designed by MATLAB simulation is explained and its results are expressed. Finally, a prototype of the system was made and the ability of the energy-harvesting device to absorb the original system vibrations, as well as parameters impact on the efficiency of energy harvesting is investigated. Experimental results show that the energy-harvesting device, in addition to producing electric current with a maximum value of 1.5V, reduces 94% of the original system vibrations.

Cargo Movement Operation Systems (CMOS) Interface Design Document (Preliminary)

DTIC Science & Technology

1990-04-29

between these versions, each must be individually numbered. CMOS PMO ACCEPTS COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION...ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: IDDl-0004 PROGRAM OFFICE CONTROL NUMBER...COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: IDDl-0006

CRBRP modular steam generator tube-to-tubesheet and shell-closure welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Viri, D.P.

1982-01-01

The original Modular Steam Generator (MSG), whiand inh was designed, built, and tested by the Energy Systems Group (ESG) of Rockwell International, was a departure from conventional boilers or heat exchangers. The design was a hockeystick concept - the upper section of the generator is curved 90/sup 0/. Factors affecting operating parameters were considered and incorporated in the original MSG design. The MSG was fully instrumented and functionally tested at the Energy Technology Engineering Center at Rockwell. The MSG steamed continuously for over 4000 h, and at the conclusion of the 9000-h test cycle, it was systematically dismantled and examinedmore » for wear to critical components. This paper explains the solutions to several manufacturing challenges presented by the unique design of the MSG.« less

Control by model error estimation

NASA Technical Reports Server (NTRS)

Likins, P. W.; Skelton, R. E.

1976-01-01

Modern control theory relies upon the fidelity of the mathematical model of the system. Truncated modes, external disturbances, and parameter errors in linear system models are corrected by augmenting to the original system of equations an 'error system' which is designed to approximate the effects of such model errors. A Chebyshev error system is developed for application to the Large Space Telescope (LST).

Atrium building study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-01-01

The CIGNA design team was faced with creating a new 500,000 square foot office building on a pastoral 610 acre corporate campus in Bloomfield, Connecticut, just outside of Hartford. Challenges abounded during the design process, from the selection of a specific building site on the sprawling campus to the evolution of a building form incorporating an atrium, to the selection of building systems and materials, to the design to the office interiors and atrium landscape. This document summarizes the original design problem, focusing on design criteria and performance standards that led to the decision to design an atrium building asmore » well as decision concerning its function, its form, its building systems and materials, and its passive energy strategies.« less

Random Access Frame (RAF) System Neutral Buoyancy Evaluations

NASA Technical Reports Server (NTRS)

Howe, A. Scott; Polit-Casillas, Raul; Akin, David L.; McBryan, Katherine; Carlsen, Christopher

2015-01-01

The Random Access Frame (RAF) concept is a system for organizing internal layouts of space habitats, vehicles, and outposts. The RAF system is designed as a more efficient improvement over the current International Standard Payload Rack (ISPR) used on the International Space Station (ISS), which was originally designed to allow for swapping and resupply by the Space Shuttle. The RAF system is intended to be applied in variable gravity or microgravity environments. This paper discusses evaluations and results of testing the RAF system in a neutral buoyancy facility simulating low levels of gravity that might be encountered in a deep space environment.

Earth Systems Education: Origins and Opportunities. Science Education for Global Understanding. Second Edition.

ERIC Educational Resources Information Center

University of Northern Colorado, Greeley.

This publication introduces and provides a framework for Earth Systems Education (ESE), an effort to establish within U.S. schools more effective programs designed to increase the public's understanding of the Earth system. The publication presents seven "understandings" around which curriculum can be organized and materials selected in…

What is the Final Verification of Engineering Requirements?

NASA Technical Reports Server (NTRS)

Poole, Eric

2010-01-01

This slide presentation reviews the process of development through the final verification of engineering requirements. The definition of the requirements is driven by basic needs, and should be reviewed by both the supplier and the customer. All involved need to agree upon a formal requirements including changes to the original requirements document. After the requirements have ben developed, the engineering team begins to design the system. The final design is reviewed by other organizations. The final operational system must satisfy the original requirements, though many verifications should be performed during the process. The verification methods that are used are test, inspection, analysis and demonstration. The plan for verification should be created once the system requirements are documented. The plan should include assurances that every requirement is formally verified, that the methods and the responsible organizations are specified, and that the plan is reviewed by all parties. The options of having the engineering team involved in all phases of the development as opposed to having some other organization continue the process once the design has been complete is discussed.

EAF Management Optimization

NASA Astrophysics Data System (ADS)

Costoiu, M.; Ioana, A.; Semenescu, A.; Marcu, D.

2016-11-01

The article presents the main advantages of electric arc furnace (EAF): it has a great contribution to reintroduce significant quantities of reusable metallic materials in the economic circuit, it constitutes itself as an important part in the Primary Materials and Energy Recovery (PMER), good productivity, good quality / price ratio, the possibility of developing a wide variety of classes and types of steels, including special steels and high alloy. In this paper it is presented some important developments of electric arc furnace: vacuum electric arc furnace, artificial intelligence expert systems for pollution control Steelworks. Another important aspect presented in the article is an original block diagram for optimization the EAF management system. This scheme is based on the original objective function (criterion function) represented by the price / quality ratio. The article presents an original block diagram for optimization the control system of the EAF. For designing this concept of EAF management system, many principles were used.

Multiline radar scan

NASA Technical Reports Server (NTRS)

Levinson, S.

1977-01-01

Scanning scheme is more efficient than conventional scanning. Originally designed for optical radar in space vehicles, scheme may also find uses in site-surveillance security systems and in other industrial applications. It should be particularly useful when system must run on battery energy, as would be case in power outages.

Automotive Fuel and Exhaust Systems.

ERIC Educational Resources Information Center

Marine Corps Inst., Washington, DC.

This correspondence course, originally developed for the Marine Corps, is designed to provide mechanics with an understanding of the construction, operation, malfunction, diagnosis, maintenance, and repair of the fuel and exhaust systems used in automobiles. The course contains five study units covering fundamentals of gasoline engine fuel…

Novel solutions to low-frequency problems with geometrically designed beam-waveguide systems

NASA Technical Reports Server (NTRS)

Imbriale, W. A.; Esquivel, M. S.; Manshadi, F.

1995-01-01

The poor low-frequency performance of geometrically designed beam-waveguide (BWG) antennas is shown to be caused by the diffraction phase centers being far from the geometrical optics mirror focus, resulting in substantial spillover and defocusing loss. Two novel solutions are proposed: (1) reposition the mirrors to focus low frequencies and redesign the high frequencies to utilize the new mirror positions, and (2) redesign the input feed system to provide an optimum solution for the low frequency. A novel use of the conjugate phase-matching technique is utilized to design the optimum low-frequency feed system, and the new feed system has been implemented in the JPL research and development BWG as part of a dual S-/X-band (2.3 GHz/8.45 GHz) feed system. The new S-band feed system is shown to perform significantly better than the original geometrically designed system.

Solar heating system final design package

NASA Technical Reports Server (NTRS)

1979-01-01

The system is composed of a warm air collector, a logic control unit and a universal switching and transport unit. The collector was originally conceived and designed as an integrated roof/wall system and therefore provides a dual function in the structure. The collector serves both as a solar energy conversion system and as a structural weather resistant skin. The control unit provides totally automatic control over the operation of the system. It receives input data from sensor probes in collectors, storage and living space. The logic was designed so as to make maximum use of solar energy and minimize use of conventional energy. The transport and switching unit is a high-efficiency air-handling system equipped with gear motor valves that respond to outputs from the control system. The fan unit was designed for maximum durability and efficiency in operation, and has permanently lubricated ball bearings and excellent air-handling efficiency.

A Comparison of Reinforcement Sensitivity Theory Measures: Unique Associations With Social Interaction Anxiety and Social Observation Anxiety.

PubMed

Kramer, Sam L; Rodriguez, Benjamin F

2018-07-01

Evidence suggests that the behavior inhibition system (BIS) and fight-flight-freeze system play a role in the individual differences seen in social anxiety disorder; however, findings concerning the role of the behavior approach system (BAS) have been mixed. To date, the role of revised reinforcement sensitivity theory (RST) subsystems underlying social anxiety has been measured with scales designed for the original RST. This study examined how the BIS, BAS, and fight, flight, freeze components of the fight-flight-freeze system uniquely relate to social interaction anxiety and social observation anxiety using both a measure specifically designed for the revised RST and a commonly used original RST measure. Comparison of regression analyses with the Jackson-5 and the commonly used BIS/BAS Scales revealed important differences in the relationships between RST subsystems and social anxiety depending on how RST was assessed. Limitations and future directions for revised RST measurement are discussed.

Fuzzy model-based servo and model following control for nonlinear systems.

PubMed

Ohtake, Hiroshi; Tanaka, Kazuo; Wang, Hua O

2009-12-01

This correspondence presents servo and nonlinear model following controls for a class of nonlinear systems using the Takagi-Sugeno fuzzy model-based control approach. First, the construction method of the augmented fuzzy system for continuous-time nonlinear systems is proposed by differentiating the original nonlinear system. Second, the dynamic fuzzy servo controller and the dynamic fuzzy model following controller, which can make outputs of the nonlinear system converge to target points and to outputs of the reference system, respectively, are introduced. Finally, the servo and model following controller design conditions are given in terms of linear matrix inequalities. Design examples illustrate the utility of this approach.

The role of networks and artificial intelligence in nanotechnology design and analysis.

PubMed

Hudson, D L; Cohen, M E

2004-05-01

Techniques with their origins in artificial intelligence have had a great impact on many areas of biomedicine. Expert-based systems have been used to develop computer-assisted decision aids. Neural networks have been used extensively in disease classification and more recently in many bioinformatics applications including genomics and drug design. Network theory in general has proved useful in modeling all aspects of biomedicine from healthcare organizational structure to biochemical pathways. These methods show promise in applications involving nanotechnology both in the design phase and in interpretation of system functioning.

Optical design and testing: introduction.

PubMed

Liang, Chao-Wen; Koshel, John; Sasian, Jose; Breault, Robert; Wang, Yongtian; Fang, Yi Chin

2014-10-10

Optical design and testing has numerous applications in industrial, military, consumer, and medical settings. Assembling a complete imaging or nonimage optical system may require the integration of optics, mechatronics, lighting technology, optimization, ray tracing, aberration analysis, image processing, tolerance compensation, and display rendering. This issue features original research ranging from the optical design of image and nonimage optical stimuli for human perception, optics applications, bio-optics applications, 3D display, solar energy system, opto-mechatronics to novel imaging or nonimage modalities in visible and infrared spectral imaging, modulation transfer function measurement, and innovative interferometry.

Development of the automated bunker door by using a microcontroller-system

NASA Astrophysics Data System (ADS)

Ahmad, M. A.; Leo, K. W.; Mohamad, G. H. P.; Ahmad, A.; Hashim, S. A.; Chulan, R. M.; Baijan, A. H.

2018-01-01

The new low energy electron beam accelerator bunker was designed and built locally to allocate a 500 keV electron beam accelerator at Block 43T in Malaysian Nuclear Agency. This bunker is equipped with a locally made radiation shielding door of 10 tons. Originally, this door is moving manually by a wheel and fitted with a gear system. However, it is still heavy and need longer time to operate it manually. To overcome those issues, a new automated control system has been designed and developed. In this paper, the complete steps and design of automated control system based on the microcontroller (PIC16F84A) is described.

Developing Ultra Reliable Life Support for the Moon and Mars

NASA Technical Reports Server (NTRS)

Jones, Harry W.

2009-01-01

Recycling life support systems can achieve ultra reliability by using spares to replace failed components. The added mass for spares is approximately equal to the original system mass, provided the original system reliability is not very low. Acceptable reliability can be achieved for the space shuttle and space station by preventive maintenance and by replacing failed units, However, this maintenance and repair depends on a logistics supply chain that provides the needed spares. The Mars mission must take all the needed spares at launch. The Mars mission also must achieve ultra reliability, a very low failure rate per hour, since it requires years rather than weeks and cannot be cut short if a failure occurs. Also, the Mars mission has a much higher mass launch cost per kilogram than shuttle or station. Achieving ultra reliable space life support with acceptable mass will require a well-planned and extensive development effort. Analysis must define the reliability requirement and allocate it to subsystems and components. Technologies, components, and materials must be designed and selected for high reliability. Extensive testing is needed to ascertain very low failure rates. Systems design should segregate the failure causes in the smallest, most easily replaceable parts. The systems must be designed, produced, integrated, and tested without impairing system reliability. Maintenance and failed unit replacement should not introduce any additional probability of failure. The overall system must be tested sufficiently to identify any design errors. A program to develop ultra reliable space life support systems with acceptable mass must start soon if it is to produce timely results for the moon and Mars.

Brain imaging registry for neurologic diagnosis and research

NASA Astrophysics Data System (ADS)

Hoo, Kent S., Jr.; Wong, Stephen T. C.; Knowlton, Robert C.; Young, Geoffrey S.; Walker, John; Cao, Xinhua; Dillon, William P.; Hawkins, Randall A.; Laxer, Kenneth D.

2002-05-01

The purpose of this paper is to demonstrate the importance of building a brain imaging registry (BIR) on top of existing medical information systems including Picture Archiving Communication Systems (PACS) environment. We describe the design framework for a cluster of data marts whose purpose is to provide clinicians and researchers efficient access to a large volume of raw and processed patient images and associated data originating from multiple operational systems over time and spread out across different hospital departments and laboratories. The framework is designed using object-oriented analysis and design methodology. The BIR data marts each contain complete image and textual data relating to patients with a particular disease.

A History of U.S. Navy Periscope Detection Radar, Sensor Design and Development

DTIC Science & Technology

2014-12-31

A History of U.S. Navy Periscope Detection Radar Sensor Design and Development John G. Shannon Paul M. Moser Rite-Solutions, Inc...superiority through the years. Highly effective radar sensors used for military applications were originally large ground-based units designed, developed...automatically. Until very recently, all fleet operational periscope detection radar (PDR) sensor systems have required a skilled and alert human

System Guidelines for EMC Safety-Critical Circuits: Design, Selection, and Margin Demonstration

NASA Technical Reports Server (NTRS)

Lawton, R. M.

1996-01-01

Demonstration of required safety margins on critical electrical/electronic circuits in large complex systems has become an implementation and cost problem. These margins are the difference between the activation level of the circuit and the electrical noise on the circuit in the actual operating environment. This document discusses the origin of the requirement and gives a detailed process flow for the identification of the system electromagnetic compatibility (EMC) critical circuit list. The process flow discusses the roles of engineering disciplines such as systems engineering, safety, and EMC. Design and analysis guidelines are provided to assist the designer in assuring the system design has a high probability of meeting the margin requirements. Examples of approaches used on actual programs (Skylab and Space Shuttle Solid Rocket Booster) are provided to show how variations of the approach can be used successfully.

Application of uniform design to improve dental implant system.

PubMed

Cheng, Yung-Chang; Lin, Deng-Huei; Jiang, Cho-Pei

2015-01-01

This paper introduces the application of uniform experimental design to improve dental implant systems subjected to dynamic loads. The dynamic micromotion of the Zimmer dental implant system is calculated and illustrated by explicit dynamic finite element analysis. Endogenous and exogenous factors influence the success rate of dental implant systems. Endogenous factors include: bone density, cortical bone thickness and osseointegration. Exogenous factors include: thread pitch, thread depth, diameter of implant neck and body size. A dental implant system with a crest module was selected to simulate micromotion distribution and stress behavior under dynamic loads using conventional and proposed methods. Finally, the design which caused minimum micromotion was chosen as the optimal design model. The micromotion of the improved model is 36.42 μm, with an improvement is 15.34% as compared to the original model.

KSC-2012-5908

NASA Image and Video Library

2012-10-19

VAN HORN, Texas – Blue Origin’s New Shepard crew capsule escaped to an altitude of 2,307 feet before deploying parachutes for a safe return for a pad escape test at the company's West Texas launch site. The pusher escape system was designed and developed by Blue Origin to allow crew escape in the event of an emergency during any phase of ascent for its suborbital New Shepard system. As part of an incremental development program, the results of this test will shape the design of the escape system for the company's orbital biconic-shaped Space Vehicle. The system is expected to enable full reusability of the launch vehicle, which is different from NASA's previous launch escape systems that would pull a spacecraft away from its rocket before reaching orbit. The test was part of Blue Origin's work supporting its funded Space Act Agreement with NASA during Commercial Crew Development Round 2 CCDev2). Through initiatives like CCDev2, NASA is fostering the development of a U.S. commercial crew space transportation capability with the goal of achieving safe, reliable and cost-effective access to and from the International Space Station and low-Earth orbit. After the capability is matured and available to the government and other customers, NASA could contract to purchase commercial services to meet its station crew transportation needs. For more information, visit www.nasa.gov/commercialcrew. Image credit: Blue Origin

Report of the First National Conference on PPBES in Education, June 10, 1969.

ERIC Educational Resources Information Center

Foster, Charles W., Ed.

This document contains proceedings of a conference that presented a design for applying a program planning-budgeting-evaluating system (PPBES) to educational management. Included are (1) the keynote address, tracing the origin and future of program budgeting; (2) the presentation of the educational management design developed by the Research…

76 FR 62431 - Notice of Issuance of Final Determination Concerning Certain Ethernet Switches

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

... importing 7 Series Ethernet switches assembled in China. The switches are designed to interconnect servers... country of origin of Arista's 7048, 7050, 7100, 7124, and 7500 series (``7 Series'') local area network..., packaged, and prepared for shipping. Arista's EOS TM (Extensible Operating System) software is designed to...

New Spaces for Learning: Designing College Facilities to Utilize Instructional Aids and Media. Revised.

ERIC Educational Resources Information Center

Hauf, Harold D.; And Others

Colleges need appropriate large group instructional facilities for effective and efficient use of instructional aids and media. A well planned system of facilities must provide space for learning; production, origination, and support; storage and retrieval. Design begins with a building plan--a statement, made jointly by the administrator and…

Understanding Collaborative Learning Behavior from Moodle Log Data

ERIC Educational Resources Information Center

Lu, Jingyan; Law, Nancy Wai Ying

2012-01-01

Although course management systems (CMSs) were originally designed for teachers to manage their teaching, little interest has been directed at students' learning. Moodle is usually regarded as a CMS. However, how to make full use of its powerful features and design them into learning tools has rarely been investigated. This study investigates two…

ECHO Responds to NASA's Earth Science User Community

NASA Technical Reports Server (NTRS)

Pfister, Robin; Ullman, Richard; Wichmann, Keith; Perkins, Dorothy C. (Technical Monitor)

2001-01-01

Over the past decade NASA has designed, built, evolved, and operated the Earth Observing System Data and Information System (EOSDIS) Information Management System (IMS) in order to provide user access to NASA's Earth Science data holdings. During this time revolutionary advances in technology have driven changes in NASA's approach to providing an IMS service. This paper will describe NASA's strategic planning and approach to build and evolve the EOSDIS IMS and to serve the evolving needs of NASA's Earth Science community. It discusses the original strategic plan and how lessons learned help to form a new plan, a new approach and a new system. It discusses the original technologies and how they have evolved to today.

75 FR 63040 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-14

... transients to the fuel quantity indication system, which could cause voltage levels to go beyond original..., which could cause voltage levels to go beyond original design levels between fuel tank probes and... this material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register...

Data Mining and Homeland Security: An Overview

DTIC Science & Technology

2007-01-18

originally collected. A fourth issue is privacy. Questions that may be considered include the degree to which government agencies should use and mix...commercial data with government data, whether data sources are being used for purposes other than those for which they were originally designed, and...unique or frequently represented. For example, a hardware CRS-2 3 John Makulowich, “ Government Data Mining Systems Defy Definition,” Washington

Cargo Movement Operations System (CMOS) Final Software Design Document, Change 01, Increment I

DTIC Science & Technology

1991-03-22

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDDl-0002 PROGRAM OFFICE...COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDDl-0003 PROGRAM OFFICE CONTROL NUMBER: DATA...CARMODE and SURRTG. RATIONALE: Request clarification of these deletions. CMOS PMO ACCEPTS COMMENT: YES [ ] NO [ ] ERCI ACCEPTS COMMENT: YES [ ] NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [

40 CFR 52.2299 - Original identification of plan section.

Code of Federal Regulations, 2014 CFR

2014-07-01

.../hydrocarbons in Texas designated regions 7 and 10; regulation VII; and control strategy for nitrogen oxides in... printing; rotogravure printing; surface coating processes; transfer efficiency; and vapor balance system...

40 CFR 52.2299 - Original identification of plan section.

Code of Federal Regulations, 2012 CFR

2012-07-01

.../hydrocarbons in Texas designated regions 7 and 10; regulation VII; and control strategy for nitrogen oxides in... printing; rotogravure printing; surface coating processes; transfer efficiency; and vapor balance system...

MSFC Skylab Orbital Workshop, volume 1. [systems analysis and equipment specifications for orbital laboratory

NASA Technical Reports Server (NTRS)

1974-01-01

The technical aspects of the Skylab-Orbital Workshop are discussed. Original concepts, goals, design philosophy, hardware, and testing are reported. The final flight configuration, overall test program, and mission performance are analyzed. The systems which are examined are: (1) the structural system, (2) the meteoroid shield systems, and (3) the environmental/thermal control subsystem.

Concepts, requirements, and design approaches for building successful planning and scheduling systems

NASA Technical Reports Server (NTRS)

Hornstein, Rhoda Shaller; Willoughby, John K.

1991-01-01

Traditional practice of systems engineering management assumes requirements can be precisely determined and unambiguously defined prior to system design and implementation; practice further assumes requirements are held static during implementation. Human-computer decision support systems for service planning and scheduling applications do not conform well to these assumptions. Adaptation to the traditional practice of systems engineering management are required. Basic technology exists to support these adaptations. Additional innovations must be encouraged and nutured. Continued partnership between the programmatic and technical perspective assures proper balance of the impossible with the possible. Past problems have the following origins: not recognizing the unusual and perverse nature of the requirements for planning and scheduling; not recognizing the best starting point assumptions for the design; not understanding the type of system that being built; and not understanding the design consequences of the operations concept selected.

A computer-aided design system geared toward conceptual design in a research environment. [for hypersonic vehicles

NASA Technical Reports Server (NTRS)

STACK S. H.

1981-01-01

A computer-aided design system has recently been developed specifically for the small research group environment. The system is implemented on a Prime 400 minicomputer linked with a CDC 6600 computer. The goal was to assign the minicomputer specific tasks, such as data input and graphics, thereby reserving the large mainframe computer for time-consuming analysis codes. The basic structure of the design system consists of GEMPAK, a computer code that generates detailed configuration geometry from a minimum of input; interface programs that reformat GEMPAK geometry for input to the analysis codes; and utility programs that simplify computer access and data interpretation. The working system has had a large positive impact on the quantity and quality of research performed by the originating group. This paper describes the system, the major factors that contributed to its particular form, and presents examples of its application.

Preliminary design and development of a reflectance spectrometer instrument

NASA Technical Reports Server (NTRS)

Mccord, T. B.

1979-01-01

An improved design for the reflectance spectrometer is described to be used on various terrestrial body missions. These improvements were made on the original Lunar Polar Orbiter design. These include a larger entrance mirror, rectangular aperture, multiple optical beams, spatial resolution, and a bandwidth extension to 5 microns. In addition, detailed electronic designs were produced for a charge amplifier and an amplifier/demodulator/integrator. Design of a microprocessor driven test system was begun. Laboratory tests were performed on a tuning fork chopper.

Extraterrestrial fiberglass production using solar energy. [lunar plants or space manufacturing facilities

NASA Technical Reports Server (NTRS)

Ho, D.; Sobon, L. E.

1979-01-01

A conceptual design is presented for fiberglass production systems in both lunar and space environments. The raw material, of lunar origin, will be plagioclase concentrate, high silica content slag, and calcium oxide. Glass will be melted by solar energy. The multifurnace in the lunar plant and the spinning cylinder in the space plant are unique design features. Furnace design appears to be the most critical element in optimizing system performance. A conservative estimate of the total power generated by solar concentrators is 1880 kW; the mass of both plants is 120 tons. The systems will reproduce about 90 times their total mass in fiberglass in 1 year. A new design concept would be necessary if glass rods were produced in space.

Computational methods of robust controller design for aerodynamic flutter suppression

NASA Technical Reports Server (NTRS)

Anderson, L. R.

1981-01-01

The development of Riccati iteration, a tool for the design and analysis of linear control systems is examined. First, Riccati iteration is applied to the problem of pole placement and order reduction in two-time scale control systems. Order reduction, yielding a good approximation to the original system, is demonstrated using a 16th order linear model of a turbofan engine. Next, a numerical method for solving the Riccati equation is presented and demonstrated for a set of eighth order random examples. A literature review of robust controller design methods follows which includes a number of methods for reducing the trajectory and performance index sensitivity in linear regulators. Lastly, robust controller design for large parameter variations is discussed.

Application of Energy Integration Techniques to the Design of Advanced Life Support Systems

NASA Technical Reports Server (NTRS)

Levri, Julie; Finn, Cory

2000-01-01

Exchanging heat between hot and cold streams within an advanced life support system can save energy. This savings will reduce the equivalent system mass (ESM) of the system. Different system configurations are examined under steady-state conditions for various percentages of food growth and waste treatment. The scenarios investigated represent possible design options for a Mars reference mission. Reference mission definitions are drawn from the ALSS Modeling and Analysis Reference Missions Document, which includes definitions for space station evolution, Mars landers, and a Mars base. For each scenario, streams requiring heating or cooling are identified and characterized by mass flow, supply and target temperatures and heat capacities. The Pinch Technique is applied to identify good matches for energy exchange between the hot and cold streams and to calculate the minimum external heating and cooling requirements for the system. For each pair of hot and cold streams that are matched, there will be a reduction in the amount of external heating and cooling required, and the original heating and cooling equipment will be replaced with a heat exchanger. The net cost savings can be either positive or negative for each stream pairing, and the priority for implementing each pairing can be ranked according to its potential cost savings. Using the Pinch technique, a complete system heat exchange network is developed and heat exchangers are sized to allow for calculation of ESM. The energy-integrated design typically has a lower total ESM than the original design with no energy integration. A comparison of ESM savings in each of the scenarios is made to direct future Pinch Analysis efforts.

Real Time Fire Reconnaissance Satellite Monitoring System Failure Model

NASA Astrophysics Data System (ADS)

Nino Prieto, Omar Ariosto; Colmenares Guillen, Luis Enrique

2013-09-01

In this paper the Real Time Fire Reconnaissance Satellite Monitoring System is presented. This architecture is a legacy of the Detection System for Real-Time Physical Variables which is undergoing a patent process in Mexico. The methodologies for this design are the Structured Analysis for Real Time (SA- RT) [8], and the software is carried out by LACATRE (Langage d'aide à la Conception d'Application multitâche Temps Réel) [9,10] Real Time formal language. The system failures model is analyzed and the proposal is based on the formal language for the design of critical systems and Risk Assessment; AltaRica. This formal architecture uses satellites as input sensors and it was adapted from the original model which is a design pattern for physical variation detection in Real Time. The original design, whose task is to monitor events such as natural disasters and health related applications, or actual sickness monitoring and prevention, as the Real Time Diabetes Monitoring System, among others. Some related work has been presented on the Mexican Space Agency (AEM) Creation and Consultation Forums (2010-2011), and throughout the International Mexican Aerospace Science and Technology Society (SOMECYTA) international congress held in San Luis Potosí, México (2012). This Architecture will allow a Real Time Fire Satellite Monitoring, which will reduce the damage and danger caused by fires which consumes the forests and tropical forests of Mexico. This new proposal, permits having a new system that impacts on disaster prevention, by combining national and international technologies and cooperation for the benefit of humankind.

Measuring whole-plant transpiration gravimetrically: a scalable automated system built from components

Treesearch

Damian Cirelli; Victor J. Lieffers; Melvin T. Tyree

2012-01-01

Measuring whole-plant transpiration is highly relevant considering the increasing interest in understanding and improving plant water use at the whole-plant level. We present an original software package (Amalthea) and a design to create a system for measuring transpiration using laboratory balances based on the readily available commodity hardware. The system is...

An Overview of the Naval Enlisted Professional Development Information System (NEPDIS). Focus on the Trained Person.

ERIC Educational Resources Information Center

Ansbro, Thomas M.

This is the first in a series of reports describing the origin, development, and applications of the Naval Enlisted Professional Development Information System (NEPDIS). The NEPDIS was designed to be a fully computerized information assembly and analysis system that would eventually support manpower, personnel, and training management. This report…

A post audit of a model-designed ground water extraction system.

PubMed

Andersen, Peter F; Lu, Silong

2003-01-01

Model post audits test the predictive capabilities of ground water models and shed light on their practical limitations. In the work presented here, ground water model predictions were used to design an extraction/treatment/injection system at a military ammunition facility and then were re-evaluated using site-specific water-level data collected approximately one year after system startup. The water-level data indicated that performance specifications for the design, i.e., containment, had been achieved over the required area, but that predicted water-level changes were greater than observed, particularly in the deeper zones of the aquifer. Probable model error was investigated by determining the changes that were required to obtain an improved match to observed water-level changes. This analysis suggests that the originally estimated hydraulic properties were in error by a factor of two to five. These errors may have resulted from attributing less importance to data from deeper zones of the aquifer and from applying pumping test results to a volume of material that was larger than the volume affected by the pumping test. To determine the importance of these errors to the predictions of interest, the models were used to simulate the capture zones resulting from the originally estimated and updated parameter values. The study suggests that, despite the model error, the ground water model contributed positively to the design of the remediation system.

Supporting Effective Collaboration: Using a Rearview Mirror to Look Forward

ERIC Educational Resources Information Center

McManus, Margaret M.; Aiken, Robert M.

2016-01-01

Our original research, to design and develop an Intelligent Collaborative Learning System (ICLS), yielded the creation of a Group Leader Tutor software system which utilizes a Collaborative Skills Network to monitor students working collaboratively in a networked environment. The Collaborative Skills Network was a conceptualization of…

Ultra Reliable Closed Loop Life Support for Long Space Missions

NASA Technical Reports Server (NTRS)

Jones, Harry W.; Ewert, Michael K.

2010-01-01

Spacecraft human life support systems can achieve ultra reliability by providing sufficient spares to replace all failed components. The additional mass of spares for ultra reliability is approximately equal to the original system mass, provided that the original system reliability is not too low. Acceptable reliability can be achieved for the Space Shuttle and Space Station by preventive maintenance and by replacing failed units. However, on-demand maintenance and repair requires a logistics supply chain in place to provide the needed spares. In contrast, a Mars or other long space mission must take along all the needed spares, since resupply is not possible. Long missions must achieve ultra reliability, a very low failure rate per hour, since they will take years rather than weeks and cannot be cut short if a failure occurs. Also, distant missions have a much higher mass launch cost per kilogram than near-Earth missions. Achieving ultra reliable spacecraft life support systems with acceptable mass will require a well-planned and extensive development effort. Analysis must determine the reliability requirement and allocate it to subsystems and components. Ultra reliability requires reducing the intrinsic failure causes, providing spares to replace failed components and having "graceful" failure modes. Technologies, components, and materials must be selected and designed for high reliability. Long duration testing is needed to confirm very low failure rates. Systems design should segregate the failure causes in the smallest, most easily replaceable parts. The system must be designed, developed, integrated, and tested with system reliability in mind. Maintenance and reparability of failed units must not add to the probability of failure. The overall system must be tested sufficiently to identify any design errors. A program to develop ultra reliable space life support systems with acceptable mass should start soon since it must be a long term effort.

The effect of a loss of model structural detail due to network skeletonization on contamination warning system design: case studies.

PubMed

Davis, Michael J; Janke, Robert

2018-01-04

The effect of limitations in the structural detail available in a network model on contamination warning system (CWS) design was examined in case studies using the original and skeletonized network models for two water distribution systems (WDSs). The skeletonized models were used as proxies for incomplete network models. CWS designs were developed by optimizing sensor placements for worst-case and mean-case contamination events. Designs developed using the skeletonized network models were transplanted into the original network model for evaluation. CWS performance was defined as the number of people who ingest more than some quantity of a contaminant in tap water before the CWS detects the presence of contamination. Lack of structural detail in a network model can result in CWS designs that (1) provide considerably less protection against worst-case contamination events than that obtained when a more complete network model is available and (2) yield substantial underestimates of the consequences associated with a contamination event. Nevertheless, CWSs developed using skeletonized network models can provide useful reductions in consequences for contaminants whose effects are not localized near the injection location. Mean-case designs can yield worst-case performances similar to those for worst-case designs when there is uncertainty in the network model. Improvements in network models for WDSs have the potential to yield significant improvements in CWS designs as well as more realistic evaluations of those designs. Although such improvements would be expected to yield improved CWS performance, the expected improvements in CWS performance have not been quantified previously. The results presented here should be useful to those responsible for the design or implementation of CWSs, particularly managers and engineers in water utilities, and encourage the development of improved network models.

The effect of a loss of model structural detail due to network skeletonization on contamination warning system design: case studies

NASA Astrophysics Data System (ADS)

Davis, Michael J.; Janke, Robert

2018-05-01

The effect of limitations in the structural detail available in a network model on contamination warning system (CWS) design was examined in case studies using the original and skeletonized network models for two water distribution systems (WDSs). The skeletonized models were used as proxies for incomplete network models. CWS designs were developed by optimizing sensor placements for worst-case and mean-case contamination events. Designs developed using the skeletonized network models were transplanted into the original network model for evaluation. CWS performance was defined as the number of people who ingest more than some quantity of a contaminant in tap water before the CWS detects the presence of contamination. Lack of structural detail in a network model can result in CWS designs that (1) provide considerably less protection against worst-case contamination events than that obtained when a more complete network model is available and (2) yield substantial underestimates of the consequences associated with a contamination event. Nevertheless, CWSs developed using skeletonized network models can provide useful reductions in consequences for contaminants whose effects are not localized near the injection location. Mean-case designs can yield worst-case performances similar to those for worst-case designs when there is uncertainty in the network model. Improvements in network models for WDSs have the potential to yield significant improvements in CWS designs as well as more realistic evaluations of those designs. Although such improvements would be expected to yield improved CWS performance, the expected improvements in CWS performance have not been quantified previously. The results presented here should be useful to those responsible for the design or implementation of CWSs, particularly managers and engineers in water utilities, and encourage the development of improved network models.

Advanced Information Technology in Simulation Based Life Cycle Design

NASA Technical Reports Server (NTRS)

Renaud, John E.

2003-01-01

In this research a Collaborative Optimization (CO) approach for multidisciplinary systems design is used to develop a decision based design framework for non-deterministic optimization. To date CO strategies have been developed for use in application to deterministic systems design problems. In this research the decision based design (DBD) framework proposed by Hazelrigg is modified for use in a collaborative optimization framework. The Hazelrigg framework as originally proposed provides a single level optimization strategy that combines engineering decisions with business decisions in a single level optimization. By transforming this framework for use in collaborative optimization one can decompose the business and engineering decision making processes. In the new multilevel framework of Decision Based Collaborative Optimization (DBCO) the business decisions are made at the system level. These business decisions result in a set of engineering performance targets that disciplinary engineering design teams seek to satisfy as part of subspace optimizations. The Decision Based Collaborative Optimization framework more accurately models the existing relationship between business and engineering in multidisciplinary systems design.

Power flow prediction in vibrating systems via model reduction

NASA Astrophysics Data System (ADS)

Li, Xianhui

This dissertation focuses on power flow prediction in vibrating systems. Reduced order models (ROMs) are built based on rational Krylov model reduction which preserve power flow information in the original systems over a specified frequency band. Stiffness and mass matrices of the ROMs are obtained by projecting the original system matrices onto the subspaces spanned by forced responses. A matrix-free algorithm is designed to construct ROMs directly from the power quantities at selected interpolation frequencies. Strategies for parallel implementation of the algorithm via message passing interface are proposed. The quality of ROMs is iteratively refined according to the error estimate based on residual norms. Band capacity is proposed to provide a priori estimate of the sizes of good quality ROMs. Frequency averaging is recast as ensemble averaging and Cauchy distribution is used to simplify the computation. Besides model reduction for deterministic systems, details of constructing ROMs for parametric and nonparametric random systems are also presented. Case studies have been conducted on testbeds from Harwell-Boeing collections. Input and coupling power flow are computed for the original systems and the ROMs. Good agreement is observed in all cases.

Advanced system for 3D dental anatomy reconstruction and 3D tooth movement simulation during orthodontic treatment

NASA Astrophysics Data System (ADS)

Monserrat, Carlos; Alcaniz-Raya, Mariano L.; Juan, M. Carmen; Grau Colomer, Vincente; Albalat, Salvador E.

1997-05-01

This paper describes a new method for 3D orthodontics treatment simulation developed for an orthodontics planning system (MAGALLANES). We develop an original system for 3D capturing and reconstruction of dental anatomy that avoid use of dental casts in orthodontic treatments. Two original techniques are presented, one direct in which data are acquired directly form patient's mouth by mean of low cost 3D digitizers, and one mixed in which data are obtained by 3D digitizing of hydrocollids molds. FOr this purpose we have designed and manufactured an optimized optical measuring system based on laser structured light. We apply these 3D dental models to simulate 3D movement of teeth, including rotations, during orthodontic treatment. The proposed algorithms enable to quantify the effect of orthodontic appliance on tooth movement. The developed techniques has been integrated in a system named MAGALLANES. This original system present several tools for 3D simulation and planning of orthodontic treatments. The prototype system has been tested in several orthodontic clinic with very good results.

Data Mining and Homeland Security: An Overview

DTIC Science & Technology

2007-03-28

originally collected. A fourth issue is privacy. Questions that may be considered include the degree to which government agencies should use and mix...commercial data with government data, whether data sources are being used for purposes other than those for which they were originally designed, and...frequently represented. For example, a hardware CRS-2 3 John Makulowich, “ Government Data Mining Systems Defy Definition,” Washington Technology, 22 February

Design and implementation of fishery rescue data mart system

NASA Astrophysics Data System (ADS)

Pan, Jun; Huang, Haiguang; Liu, Yousong

A novel data mart based system for fishery rescue field was designed and implemented. The system runs ETL process to deal with original data from various databases and data warehouses, and then reorganized the data into the fishery rescue data mart. Next, online analytical processing (OLAP) are carried out and statistical reports are generated automatically. Particularly, quick configuration schemes are designed to configure query dimensions and OLAP data sets. The configuration file will be transformed into statistic interfaces automatically through a wizard-style process. The system provides various forms of reporting files, including crystal reports, flash graphical reports, and two-dimensional data grids. In addition, a wizard style interface was designed to guide users customizing inquiry processes, making it possible for nontechnical staffs to access customized reports. Characterized by quick configuration, safeness and flexibility, the system has been successfully applied in city fishery rescue department.

General Electromagnetic Model for the Analysis of Complex Systems (GEMACS) Engineering Manual (Version 3). Volume 3.

DTIC Science & Technology

1983-09-01

processor. How- ever, upon completion of the restart initialization, additional commands may be added or original commands deleted with normal input...written IOSI Scratch logical unit designator IOS1SV Saved value of lOS1 IOS2 Scratch logical unit designator IR Index pointer to upper triangular matrix

Modeling and stability of segmented reflector telescopes - A decentralized approach

NASA Technical Reports Server (NTRS)

Ryaciotaki-Boussalis, Helen A.; Ih, Che-Hang Charles

1990-01-01

The decentralization of a segmented reflector telescope based on a finite-element model of its structure is considered. The decentralization of the system at the panel level is considered. Each panel is originally treated as an isolated subsystem so that the controller design is performed independently at the local level, and then applied to the composite system for stability analysis. The panel-level control laws were designed by means of pole placement using local output feedback. Simulation results show a better 1000:1 vibration attenuation in panel position when compared to the open-loop system. It is shown that the overall closed-loop system is exponentially stable provided that certain conditions are met. The advantage to the decentralized approach is that the design is performed in terms of the low-dimensionality subsystems, thus drastically reducing the design computational complexities.

THERMAL DESIGN OF THE ITER VACUUM VESSEL COOLING SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbajo, Juan J; Yoder Jr, Graydon L; Kim, Seokho H

RELAP5-3D models of the ITER Vacuum Vessel (VV) Primary Heat Transfer System (PHTS) have been developed. The design of the cooling system is described in detail, and RELAP5 results are presented. Two parallel pump/heat exchanger trains comprise the design one train is for full-power operation and the other is for emergency operation or operation at decay heat levels. All the components are located inside the Tokamak building (a significant change from the original configurations). The results presented include operation at full power, decay heat operation, and baking operation. The RELAP5-3D results confirm that the design can operate satisfactorily during bothmore » normal pulsed power operation and decay heat operation. All the temperatures in the coolant and in the different system components are maintained within acceptable operating limits.« less

Fast correlation method for passive-solar design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wray, W.O.; Biehl, F.A.; Kosiewicz, C.E.

1982-01-01

A passive-solar design manual for single-family detached residences and dormitory-type buildings is being developed. The design procedure employed in the manual is a simplification of the original monthly solar load ratio (SLR) method. The new SLR correlations involve a single constant for each system. The correlation constant appears as a scale factor permitting the use of a universal performance curve for all passive systems. Furthermore, by providing location-dependent correlations between the annual solar heating fraction (SHF) and the minimum monthly SHF, we have eliminated the need to perform an SLR calculation for each month of the heating season.

A passive-solar design manual for the United States Navy

NASA Astrophysics Data System (ADS)

Wray, W. O.; Biehl, F. A.; Kosiewicz, C. E.; Miles, C. E.; Durlak, E. R.

1982-06-01

A passive solar design manual for single-family detached residences and dormitory-type buildings is developed. The design procedure employed in the manual is a simplification of the original monthly solar load ratio (SLR) method. The new SLR correlations involve a single constant for each system. The correlation constant appears as a scale factor permitting the use of a universal performance curve for all passive systems. Furthermore, by providing location-dependent correlations between the annual solar heating fraction (SHF) and the minimum monthly SHF, the need to perform an SLR calculation for each month of the heating season is eliminated.

Passive-solar design manual for the United States Navy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wray, W.O.; Biehl, F.A.; Kosiewicz, C.R.

1982-01-01

A passive solar design manual for single-family detached residences and dormitory-type buildings is being developed. The design procedure employed in the manual is a simplification of the original monthly solar load ratio (SLR) method. The new SLR correlations involve a single constant for each system. The correlation constant appears as a scale factor permitting the use of a universal performance curve for all passive systems. Furthermore, by providing location-dependent correlations between the annual solar heating fraction (SHF)* and the minimum monthly SHF, we have eliminated the need to perform an SLR calculation for each month of the heating season.

Trajectory Design Strategies for the NGST L2 Libration Point Mission

NASA Technical Reports Server (NTRS)

Folta, David; Cooley, Steven; Howell, Kathleen; Bauer, Frank H.

2001-01-01

The Origins' Next Generation Space Telescope (NGST) trajectory design is addressed in light of improved methods for attaining constrained orbit parameters and their control at the exterior collinear libration point, L2. The use of a dynamical systems approach, state-space equations for initial libration orbit control, and optimization to achieve constrained orbit parameters are emphasized. The NGST trajectory design encompasses a direct transfer and orbit maintenance under a constant acceleration. A dynamical systems approach can be used to provide a biased orbit and stationkeeping maintenance method that incorporates the constraint of a single axis correction scheme.

Design of electromagnetic bearing for vibration control of flexible transmission shaft

NASA Technical Reports Server (NTRS)

Gondhalekar, V.; Holmes, R.

1984-01-01

Recently magnetic bearings were proposed by several researchers and shown to be viable on a variety of rotor assemblies. The design and construction of such a bearing, which employs features hitherto not used by other workers is examined. These include an original approach to the design of the electromagnets and their amplifiers, and to software in a digital control system, to condition the control signals so as to make the magnets appear to be linear and uncoupled. The resulting system is used to control a rotor-bearing assembly, whose speed range covers two flexural-critical speeds.

Optimal Golomb Ruler Sequences Generation for Optical WDM Systems: A Novel Parallel Hybrid Multi-objective Bat Algorithm

NASA Astrophysics Data System (ADS)

Bansal, Shonak; Singh, Arun Kumar; Gupta, Neena

2017-02-01

In real-life, multi-objective engineering design problems are very tough and time consuming optimization problems due to their high degree of nonlinearities, complexities and inhomogeneity. Nature-inspired based multi-objective optimization algorithms are now becoming popular for solving multi-objective engineering design problems. This paper proposes original multi-objective Bat algorithm (MOBA) and its extended form, namely, novel parallel hybrid multi-objective Bat algorithm (PHMOBA) to generate shortest length Golomb ruler called optimal Golomb ruler (OGR) sequences at a reasonable computation time. The OGRs found their application in optical wavelength division multiplexing (WDM) systems as channel-allocation algorithm to reduce the four-wave mixing (FWM) crosstalk. The performances of both the proposed algorithms to generate OGRs as optical WDM channel-allocation is compared with other existing classical computing and nature-inspired algorithms, including extended quadratic congruence (EQC), search algorithm (SA), genetic algorithms (GAs), biogeography based optimization (BBO) and big bang-big crunch (BB-BC) optimization algorithms. Simulations conclude that the proposed parallel hybrid multi-objective Bat algorithm works efficiently as compared to original multi-objective Bat algorithm and other existing algorithms to generate OGRs for optical WDM systems. The algorithm PHMOBA to generate OGRs, has higher convergence and success rate than original MOBA. The efficiency improvement of proposed PHMOBA to generate OGRs up to 20-marks, in terms of ruler length and total optical channel bandwidth (TBW) is 100 %, whereas for original MOBA is 85 %. Finally the implications for further research are also discussed.

Laboratory Information Management System (LIMS): A case study

NASA Technical Reports Server (NTRS)

Crandall, Karen S.; Auping, Judith V.; Megargle, Robert G.

1987-01-01

In the late 70's, a refurbishment of the analytical laboratories serving the Materials Division at NASA Lewis Research Center was undertaken. As part of the modernization efforts, a Laboratory Information Management System (LIMS) was to be included. Preliminary studies indicated a custom-designed system as the best choice in order to satisfy all of the requirements. A scaled down version of the original design has been in operation since 1984. The LIMS, a combination of computer hardware, provides the chemical characterization laboratory with an information data base, a report generator, a user interface, and networking capabilities. This paper is an account of the processes involved in designing and implementing that LIMS.

KSC-2012-5907

NASA Image and Video Library

2012-10-19

VAN HORN, Texas – Blue Origin’s pusher escape system rockets its New Shepard crew capsule away from a simulated propulsion module launch pad at the company's West Texas launch site, demonstrating a key safety system for both suborbital and orbital flights. The pad escape test took the company's suborbital crew capsule to an altitude of 2,307 feet during the flight test before descending safely by parachute to a soft landing 1,630 feet away. The pusher escape system was designed and developed by Blue Origin to allow crew escape in the event of an emergency during any phase of ascent for its suborbital New Shepard system. As part of an incremental development program, the results of this test will shape the design of the escape system for the company's orbital biconic-shaped Space Vehicle. The system is expected to enable full reusability of the launch vehicle, which is different from NASA's previous launch escape systems that would pull a spacecraft away from its rocket before reaching orbit. The test was part of Blue Origin's work supporting its funded Space Act Agreement with NASA during Commercial Crew Development Round 2 CCDev2). Through initiatives like CCDev2, NASA is fostering the development of a U.S. commercial crew space transportation capability with the goal of achieving safe, reliable and cost-effective access to and from the International Space Station and low-Earth orbit. After the capability is matured and available to the government and other customers, NASA could contract to purchase commercial services to meet its station crew transportation needs. For more information, visit www.nasa.gov/commercialcrew. Image credit: Blue Origin

The development of a complementary expendable launch vehicle interface for an STS deployable payload

NASA Astrophysics Data System (ADS)

Eubanks, Ed; Gibb, John

1990-04-01

The development is described of an interface, the Titan Payload Adapter (TPA), between a Space Transportation System (STS) deployable payload and an expendable launch vehicle (ELV). Separate ascent and separation constraint systems allow a payload with integral trunnions to retain its originally designed, boost-phase load structure, yet also allow the expendable booster vehicle to separate from the payload via retro-rockets. Design requirements as well as development problems and their solutions are discussed.

High Impulse Gun Airborne Demonstration. GAU-13/A Weapon, Feed System, Gun Drive and Electronic Controls.

DTIC Science & Technology

1981-05-01

made to provide mounting bosses for the closed loop conveyor chute . Ten small round bosses were welded onto the housing to provide this support...became necessary to depart from previous closed loop feeder designs . The original feed system consisted of a series of conveyor elements in a flexible...The flexible chuting has been replaced with rigid chuting forming a loop around the gun housing. This design affords the maximum stiffness and hence

The development of a complementary expendable launch vehicle interface for an STS deployable payload

NASA Technical Reports Server (NTRS)

Eubanks, ED; Gibb, John

1990-01-01

The development is described of an interface, the Titan Payload Adapter (TPA), between a Space Transportation System (STS) deployable payload and an expendable launch vehicle (ELV). Separate ascent and separation constraint systems allow a payload with integral trunnions to retain its originally designed, boost-phase load structure, yet also allow the expendable booster vehicle to separate from the payload via retro-rockets. Design requirements as well as development problems and their solutions are discussed.

Water Purification Systems

NASA Technical Reports Server (NTRS)

1994-01-01

Clearwater Pool Technologies employs NASA-developed silver/copper ionization to purify turtle and dolphin tanks, cooling towers, spas, water recycling systems, etc. The pool purifier consists of a microcomputer to monitor water conditions, a pair of metallic electrodes, and a rheostat controller. Ions are generated by passing a low voltage current through the electrodes; the silver ions kill the bacteria, and the copper ions kill algae. This technology has found broad application because it offers an alternative to chemical disinfectants. It was originally developed to purify water on Apollo spacecraft. Caribbean Clear has been using NASA's silver ionization technology for water purification for more than a decade. Two new products incorporate advancements of the basic technology. One is the AquaKing, a system designed for areas with no source of acceptable drinking water. Another is the Caribbean Clear Controller, designed for commercial pool and water park applications where sanitizing is combined with feedback control of pH and an oxidizer, chlorine or bromine. The technology was originally developed to purify water on Apollo spacecraft.

Composite fuzzy sliding mode control of nonlinear singularly perturbed systems.

PubMed

Nagarale, Ravindrakumar M; Patre, B M

2014-05-01

This paper deals with the robust asymptotic stabilization for a class of nonlinear singularly perturbed systems using the fuzzy sliding mode control technique. In the proposed approach the original system is decomposed into two subsystems as slow and fast models by the singularly perturbed method. The composite fuzzy sliding mode controller is designed for stabilizing the full order system by combining separately designed slow and fast fuzzy sliding mode controllers. The two-time scale design approach minimizes the effect of boundary layer system on the full order system. A stability analysis allows us to provide sufficient conditions for the asymptotic stability of the full order closed-loop system. The simulation results show improved system performance of the proposed controller as compared to existing methods. The experimentation results validate the effectiveness of the proposed controller. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Real-time acquisition and tracking system with multiple Kalman filters

NASA Astrophysics Data System (ADS)

Beard, Gary C.; McCarter, Timothy G.; Spodeck, Walter; Fletcher, James E.

1994-07-01

The design of a real-time, ground-based, infrared tracking system with proven field success in tracking boost vehicles through burnout is presented with emphasis on the software design. The system was originally developed to deliver relative angular positions during boost, and thrust termination time to a sensor fusion station in real-time. Autonomous target acquisition and angle-only tracking features were developed to ensure success under stressing conditions. A unique feature of the system is the incorporation of multiple copies of a Kalman filter tracking algorithm running in parallel in order to minimize run-time. The system is capable of updating the state vector for an object at measurement rates approaching 90 Hz. This paper will address the top-level software design, details of the algorithms employed, system performance history in the field, and possible future upgrades.

GATE: Energy Efficient Vehicles for Sustainable Mobility-Project TI022- FinalReport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rizzoni, Giorgio

Unique opportunity for industry to engage in original, highly leveraged precompetitive research in automotive and transportation systems, with focus on advanced propulsion systems; fuel economy; vehicle safety, connectivity and autonomy; and advanced driver assistance systems Additional benefits: prepare graduate students for future careers in automotive industry, reaching undergraduate students through capstone design and other project activities, focused recruitment events

Development and flight test results of an autothrottle control system at Mach 3 cruise

NASA Technical Reports Server (NTRS)

Gilyard, G. B.; Burken, J. J.

1980-01-01

Flight test results obtained with the original Mach hold autopilot designed the YF-12C airplane which uses elevator control and a newly developed Mach hold system having an autothrottle integrated with an altitude hold autopilot system are presented. The autothrottle tests demonstrate good speed control at high Mach numbers and high altitudes while simultaneously maintaining control over altitude and good ride qualities. The autothrottle system was designed to control either Mach number or knots equivalent airspeed (KEAS). Excellent control of Mach number or KEAS was obtained with the autothrottle system when combined with altitude hold. Ride qualities were significantly better than with the conventional Mach hold system.

Development of Simulated Disturbing Source for Isolation Switch

NASA Astrophysics Data System (ADS)

Cheng, Lin; Liu, Xiang; Deng, Xiaoping; Pan, Zhezhe; Zhou, Hang; Zhu, Yong

2018-01-01

In order to simulate the substation in the actual scene of the harsh electromagnetic environment, and then research on electromagnetic compatibility testing of electronic instrument transformer, On the basis of the original isolation switch as a harassment source of the electronic instrument transformer electromagnetic compatibility test system, an isolated switch simulation source system was developed, to promote the standardization of the original test. In this paper, the circuit breaker is used to control the opening and closing of the gap arc to simulate the operating of isolating switch, and the isolation switch simulation harassment source system is designed accordingly. Comparison with the actual test results of the isolating switch, it is proved that the system can meet the test requirements, and the simulation harassment source system has good stability and high reliability.

ANALYSIS OF DESIGN RANGE FOR A STROKING SEAT ON A STROKING FLOOR TO MITIGATE BLAST LOADING EFFECTS

DTIC Science & Technology

2017-05-16

and the optimal design points that can mitigate the occupant injury to a range of input parameters. One key conclusion from the study is that blast...stroking) in another case . The results from this study are shown in Figure 10. The original two baseline design points explored in the previous...this study , occupant is positioned with feet on the foot-rest attached to the seat system. However, a particular vehicle design may have the

Description of the insulation system for the Langley 0.3-Meter Transonic Cryogenic Tunnel

NASA Technical Reports Server (NTRS)

Lawing, P. L.; Dress, D. A.; Kilgore, R. A.

1985-01-01

The thermal insulation system of the Langley 0.3 Meter Transonic Cryogenic Tunnel is described. The insulation system is designed to operate from room temperature down to about 77.4 K, the temperature of liquid nitrogen at 1 atmosphere. A detailed description is given of the primary insulation sytem consists of glass fiber mats, a three part vapor barrier, and a dry positive pressure purge system. Also described are several secondary insulation systems required for the test section, actuators, and tunnel supports. An appendix briefly describes the original insulation system which is considered inferior to the one presently in place. The time required for opening and closing portions of the insulation system for modification or repair to the tunnel has been reduced, typically, from a few days for the original thermal insulating system to a few hours for the present system.

Phase-lock-loop application for fiber optic receiver

NASA Astrophysics Data System (ADS)

Ruggles, Stephen L.; Wills, Robert W.

1991-02-01

Phase-locked loop circuits are frequently employed in communication systems. In recent years, digital phase-locked loop circuits were utilized in optical communications systems. In an optical transceiver system, the digital phase-locked loop circuit is connected to the output of the receiver to extract a clock signal from the received coded data (NRZ, Bi-Phase, or Manchester). The clock signal is then used to reconstruct or recover the original data from the coded data. A theoretical approach to the design of a digital phase-locked loop circuit operation at 1 and 50 MHz is described. Hardware implementation of a breadboard design to function at 1 MHz and a printed-circuit board designed to function at 50 MHz were assembled using emitter coupled logic (ECL) to verify experimentally the theoretical design.

Phase-lock-loop application for fiber optic receiver

NASA Technical Reports Server (NTRS)

Ruggles, Stephen L.; Wills, Robert W.

1991-01-01

Phase-locked loop circuits are frequently employed in communication systems. In recent years, digital phase-locked loop circuits were utilized in optical communications systems. In an optical transceiver system, the digital phase-locked loop circuit is connected to the output of the receiver to extract a clock signal from the received coded data (NRZ, Bi-Phase, or Manchester). The clock signal is then used to reconstruct or recover the original data from the coded data. A theoretical approach to the design of a digital phase-locked loop circuit operation at 1 and 50 MHz is described. Hardware implementation of a breadboard design to function at 1 MHz and a printed-circuit board designed to function at 50 MHz were assembled using emitter coupled logic (ECL) to verify experimentally the theoretical design.

Architectural evaluation of dynamic and partial reconfigurable systems designed with DREAMS tool

NASA Astrophysics Data System (ADS)

Otero, Andrés.; Gallego, Ángel; de la Torre, Eduardo; Riesgo, Teresa

2013-05-01

Benefits of dynamic and partial reconfigurable systems are increasingly being more accepted by the industry. For this reason, SRAM-based FPGA manufacturers have improved, or even included for the first time, the support they offer for the design of this kind of systems. However, commercial tools still offer a poor flexibility, which leads to a limited efficiency. This is witnessed by the overhead introduced by the communication primitives, as well as by the inability to relocate reconfigurable modules, among others. For this reason, authors have proposed an academic design tool called DREAMS, which targets the design of dynamically reconfigurable systems. In this paper, main features offered by DREAMS are described, comparing them with existing commercial and academic tools. Moreover, a graphic user interface (GUI) is originally described in this work, with the aim of simplifying the design process, as well as to hide the low level device dependent details to the system designer. The overall goal is to increase the designer productivity. Using the graphic interface, different reconfigurable architectures are provided as design examples. Among them, both conventional slot-based architectures and mesh type designs have been included.

Bounding the Effects of Social Experiments: Accounting for Attrition in Administrative Data

ERIC Educational Resources Information Center

Grogger, Jeffrey

2012-01-01

Background: Social experiments frequently exploit data from administrative records. However, most administrative data systems are designed to track earnings or benefit payments among residents within a single state. When an experimental participant moves across state lines, his entries in the data system of his state of origin consist entirely of…

78 FR 43234 - Agency Information Collection Activities; Submission to OMB for Reinstatement, With Change, of a...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-19

...) administrator, the Financial Crimes Enforcement Network (FinCEN) transitioned from a system originally designed... forms. FinCEN's objective is to have one electronically-filed dynamic and interactive BSA-SAR that will... and oversight of supervised institutions. \\2\\ The Board of Governors of the Federal Reserve System...

The Picture Exchange Communication System (PECS): What Do the Data Say?

ERIC Educational Resources Information Center

Sulzer-Azaroff, Beth; Hoffman, Anne O.; Horton, Catherine B.; Bondy, Andrew; Frost, Lori

2009-01-01

Originally designed to enable young children with autism lacking functional communication to initiate requests and to describe what they observed, the Picture Exchange Communication System (PECS) has been the subject of an ever-expanding body of research and development. Thirty-four peer-reviewed published reports on PECS are analyzed in this…

40 CFR 52.875 - Original identification of plan section.

Code of Federal Regulations, 2010 CFR

2010-07-01

... recommendations concerning the designation of Air Quality Maintenance Areas was submitted by letter from the State... Confidential Information, 2A-13 Registration and Permit System; Exemptions, 2A-14 Review of New or Altered... efficiency (TE) and vapor processing systems. Test methods which are developed by the state must be approved...

Software for Collaborative Engineering of Launch Rockets

NASA Technical Reports Server (NTRS)

Stanley, Thomas Troy

2003-01-01

The Rocket Evaluation and Cost Integration for Propulsion and Engineering software enables collaborative computing with automated exchange of information in the design and analysis of launch rockets and other complex systems. RECIPE can interact with and incorporate a variety of programs, including legacy codes, that model aspects of a system from the perspectives of different technological disciplines (e.g., aerodynamics, structures, propulsion, trajectory, aeroheating, controls, and operations) and that are used by different engineers on different computers running different operating systems. RECIPE consists mainly of (1) ISCRM a file-transfer subprogram that makes it possible for legacy codes executed in their original operating systems on their original computers to exchange data and (2) CONES an easy-to-use filewrapper subprogram that enables the integration of legacy codes. RECIPE provides a tightly integrated conceptual framework that emphasizes connectivity among the programs used by the collaborators, linking these programs in a manner that provides some configuration control while facilitating collaborative engineering tradeoff studies, including design to cost studies. In comparison with prior collaborative-engineering schemes, one based on the use of RECIPE enables fewer engineers to do more in less time.

Doppler Lidar System Design via Interdisciplinary Design Concept at NASA Langley Research Center - Part II

NASA Technical Reports Server (NTRS)

Crasner, Aaron I.; Scola,Salvatore; Beyon, Jeffrey Y.; Petway, Larry B.

2014-01-01

Optimized designs of the Navigation Doppler Lidar (NDL) instrument for Autonomous Landing Hazard Avoidance Technology (ALHAT) were accomplished via Interdisciplinary Design Concept (IDEC) at NASA Langley Research Center during the summer of 2013. Three branches in the Engineering Directorate and three students were involved in this joint task through the NASA Langley Aerospace Research Summer Scholars (LARSS) Program. The Laser Remote Sensing Branch (LRSB), Mechanical Systems Branch (MSB), and Structural and Thermal Systems Branch (STSB) were engaged to achieve optimal designs through iterative and interactive collaborative design processes. A preliminary design iteration was able to reduce the power consumption, mass, and footprint by removing redundant components and replacing inefficient components with more efficient ones. A second design iteration reduced volume and mass by replacing bulky components with excessive performance with smaller components custom-designed for the power system. Thermal modeling software was used to run steady state thermal analyses, which were used to both validate the designs and recommend further changes. Analyses were run on each redesign, as well as the original system. Thermal Desktop was used to run trade studies to account for uncertainty and assumptions about fan performance and boundary conditions. The studies suggested that, even if the assumptions were significantly wrong, the redesigned systems would remain within operating temperature limits.

Space Station Freedom electrical performance model

NASA Technical Reports Server (NTRS)

Hojnicki, Jeffrey S.; Green, Robert D.; Kerslake, Thomas W.; Mckissock, David B.; Trudell, Jeffrey J.

1993-01-01

The baseline Space Station Freedom electric power system (EPS) employs photovoltaic (PV) arrays and nickel hydrogen (NiH2) batteries to supply power to housekeeping and user electrical loads via a direct current (dc) distribution system. The EPS was originally designed for an operating life of 30 years through orbital replacement of components. As the design and development of the EPS continues, accurate EPS performance predictions are needed to assess design options, operating scenarios, and resource allocations. To meet these needs, NASA Lewis Research Center (LeRC) has, over a 10 year period, developed SPACE (Station Power Analysis for Capability Evaluation), a computer code designed to predict EPS performance. This paper describes SPACE, its functionality, and its capabilities.

Improving the Cybersecurity of Cyber-Physical Systems Through Behavioral Game Theory and Model Checking in Practice and in Education

DTIC Science & Technology

2016-09-15

pretest - posttest educational experiment with a control group and an original measurement instrument. Details of the treatment, which consisted of...promise of such an approach, a pretest - posttest educational experiment with a control group and an original measurement instrument was conducted...research question, a pretest - posttest experiment with a control group was designed. The research subjects were a representative sample of the

Non-Toxic Orbital Maneuvering System Engine Development

NASA Technical Reports Server (NTRS)

Green, Christopher; Claflin, Scott; Maeding, Chris; Butas, John

1999-01-01

Recent results using the Aestus engine operated with LOx/ethanol propellant are presented. An experimental program at Rocketdyne Propulsion and Power is underway to adapt this engine for the Boeing Reusable Space Systems Division non-toxic Orbital Maneuvering System/Reaction control System (OMS/RCS) system. Daimler-Chrysler Aerospace designed the Aestus as an nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) upper-stage engine for the Ariane 5. The non-toxic OMS/RCS system's preliminary design requires a LOx/ethanol (O2/C2H5OH) engine that operates with a mixture ratio of 1.8, a specific impulse of 323 seconds, and fits within the original OMS design envelope. This paper describes current efforts to meet these requirements including, investigating engine performance using LOx/ethanol, developing the en-ine system sizing package, and meeting the vehicle operation parameters. Data from hot-fire testing are also presented and discussed.

Design of bunch compressing system with suppression of coherent synchrotron radiation for ATF upgrade

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jing, Yichao; Fedurin, Mikhail; Stratakis, Diktys

2015-05-03

One of the operation modes for Accelerator Test Facility (ATF) upgrade is to provide high peak current, high quality electron beam for users. Such operation requires a bunch compressing system with a very large compression ratio. The CSR originating from the strong compressors generally could greatly degrade the quality of the electron beam. In this paper, we present our design for the entire bunch compressing system that will limit the effect of CSR on the e-beam’s quality. We discuss and detail the performance from the start to end simulation of such a compressor for ATF.

49 CFR 564.1 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requires the submission of dimensional, electrical specification, and marking/designation information, as specified in appendix A and appendix B of this part, for original equipment replaceable light sources used in motor vehicle headlighting systems. [61 FR 20500, May 7, 1996] ...

Operating guidelines for TxDOT ramp control signals.

DOT National Transportation Integrated Search

2009-01-01

The Texas Department of Transportation (TxDOT) currently maintains a Traffic Signals Manual. : Originally published in 1999, this manual provides a guide and reference for handling requests : for traffic signals on the designated State Highway System...

New PDS will predict performance of pallets made with used parts

Treesearch

John W. Clarke; Marshall S. White; Philip A. Araman

2001-01-01

The Pallet Design System (PDS) is a computer design program developed by Virginia Tech, the National Wooden Pallet & Container Association, and the U.S. Forest Service to quickly and accurately predict the performance of new wood pallets. PDS has been upgraded annually since its original version in 1984. All of the previous upgrades, however, have continued to...

Learning Program for Enhancing Visual Literacy for Non-Design Students Using a CMS to Share Outcomes

ERIC Educational Resources Information Center

Ariga, Taeko; Watanabe, Takashi; Otani, Toshio; Masuzawa, Toshimitsu

2016-01-01

This study proposes a basic learning program for enhancing visual literacy using an original Web content management system (Web CMS) to share students' outcomes in class as a blog post. It seeks to reinforce students' understanding and awareness of the design of visual content. The learning program described in this research focuses on to address…

Tunable Patch Antennas Using Microelectromechanical Systems

DTIC Science & Technology

2011-05-11

Figure 28, was selected as most suitable to this application. MetalMUMPs is a surface micromachining process with polysilicon , silicon nitride, nickel...yields. MEMS Variable Capacitor Design The MEMS capacitors reported here were an original design that features nickel and polysilicon layers as...the movable plates of a variable parallel plate capacitor. The polysilicon layer was embedded in silicon nitride for electrical isolation and suspended

An expert system to perform on-line controller restructuring for abrupt model changes

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.

1990-01-01

Work in progress on an expert system used to reconfigure and tune airframe/engine control systems on-line in real time in response to battle damage or structural failures is presented. The closed loop system is monitored constantly for changes in structure and performance, the detection of which prompts the expert system to choose and apply a particular control restructuring algorithm based on the type and severity of the damage. Each algorithm is designed to handle specific types of failures and each is applicable only in certain situations. The expert system uses information about the system model to identify the failure and to select the technique best suited to compensate for it. A depth-first search is used to find a solution. Once a new controller is designed and implemented it must be tuned to recover the original closed-loop handling qualities and responsiveness from the degraded system. Ideally, the pilot should not be able to tell the difference between the original and redesigned systems. The key is that the system must have inherent redundancy so that degraded or missing capabilities can be restored by creative use of alternate functionalities. With enough redundancy in the control system, minor battle damage affecting individual control surfaces or actuators, compressor efficiency, etc., can be compensated for such that the closed-loop performance in not noticeably altered. The work is applied to a Black Hawk/T700 system.

Integrated test system of infrared and laser data based on USB 3.0

NASA Astrophysics Data System (ADS)

Fu, Hui Quan; Tang, Lin Bo; Zhang, Chao; Zhao, Bao Jun; Li, Mao Wen

2017-07-01

Based on USB3.0, this paper presents the design method of an integrated test system for both infrared image data and laser signal data processing module. The core of the design is FPGA logic control, the design uses dual-chip DDR3 SDRAM to achieve high-speed laser data cache, and receive parallel LVDS image data through serial-to-parallel conversion chip, and it achieves high-speed data communication between the system and host computer through the USB3.0 bus. The experimental results show that the developed PC software realizes the real-time display of 14-bit LVDS original image after 14-to-8 bit conversion and JPEG2000 compressed image after decompression in software, and can realize the real-time display of the acquired laser signal data. The correctness of the test system design is verified, indicating that the interface link is normal.

Mechatronics by Analogy and Application to Legged Locomotion

NASA Astrophysics Data System (ADS)

Ragusila, Victor

A new design methodology for mechatronic systems, dubbed as Mechatronics by Analogy (MbA), is introduced and applied to designing a leg mechanism. The new methodology argues that by establishing a similarity relation between a complex system and a number of simpler models it is possible to design the former using the analysis and synthesis means developed for the latter. The methodology provides a framework for concurrent engineering of complex systems while maintaining the transparency of the system behaviour through making formal analogies between the system and those with more tractable dynamics. The application of the MbA methodology to the design of a monopod robot leg, called the Linkage Leg, is also studied. A series of simulations show that the dynamic behaviour of the Linkage Leg is similar to that of a combination of a double pendulum and a spring-loaded inverted pendulum, based on which the system kinematic, dynamic, and control parameters can be designed concurrently. The first stage of Mechatronics by Analogy is a method of extracting significant features of system dynamics through simpler models. The goal is to determine a set of simpler mechanisms with similar dynamic behaviour to that of the original system in various phases of its motion. A modular bond-graph representation of the system is determined, and subsequently simplified using two simplification algorithms. The first algorithm determines the relevant dynamic elements of the system for each phase of motion, and the second algorithm finds the simple mechanism described by the remaining dynamic elements. In addition to greatly simplifying the controller for the system, using simpler mechanisms with similar behaviour provides a greater insight into the dynamics of the system. This is seen in the second stage of the new methodology, which concurrently optimizes the simpler mechanisms together with a control system based on their dynamics. Once the optimal configuration of the simpler system is determined, the original mechanism is optimized such that its dynamic behaviour is analogous. It is shown that, if this analogy is achieved, the control system designed based on the simpler mechanisms can be directly implemented to the more complex system, and their dynamic behaviours are close enough for the system performance to be effectively the same. Finally it is shown that, for the employed objective of fast legged locomotion, the proposed methodology achieves a better design than Reduction-by-Feedback, a competing methodology that uses control layers to simplify the dynamics of the system.

ICESat-2 laser technology development

NASA Astrophysics Data System (ADS)

Edwards, Ryan; Sawruk, Nick W.; Hovis, Floyd E.; Burns, Patrick; Wysocki, Theodore; Rudd, Joe; Walters, Brooke; Fakhoury, Elias; Prisciandaro, Vincent

2013-09-01

A number of ICESat-2 system requirements drove the technology evolution and the system architecture for the laser transmitter Fibertek has developed for the mission.. These requirements include the laser wall plug efficiency, laser reliability, high PRF (10kHz), short-pulse (<1.5ns), relatively narrow spectral line-width, and wave length tunability. In response to these requirements Fibertek developed a frequency-doubled, master oscillator/power amplifier (MOPA) laser that incorporates direct pumped diode pumped Nd:YVO4 as the gain media, Another guiding force in the system design has been extensive hardware life testing that Fibertek has completed. This ongoing hardware testing and development evolved the system from the original baseline brass board design to the more robust flight laser system. The final design meets or exceeds all NASA requirements and is scalable to support future mission requirements.

The Advanced Gamma-ray Imaging System (AGIS): Schwarzschild-Couder (SC) Telescope Mechanical and Optical System Design

NASA Astrophysics Data System (ADS)

Guarino, V.; Vassiliev, V.; Buckley, J.; Byrum, K.; Falcone, A.; Fegan, S.; Finley, J.; Hanna, D.; Kaaret, P.; Konopelko, A.; Krawczynski, H.; Krennrich, F.; Romani, R.; Wagner, R.; Woods, M.

2009-05-01

The concept of a future ground-based gamma-ray observatory, AGIS, in the energy range 20 GeV to 200 TeV is based on an array of 50-100 imaging atmospheric Cherenkov telescopes (IACTs). The anticipated improvement of AGIS sensitivity, angular resolution, and reliability of operation imposes demanding technological and cost requirements on the design of IACTs. In this submission, we focus on the optical and mechanical systems for a novel Schwarzschild-Couder two-mirror aplanatic optical system originally proposed by Schwarzschild. Emerging new mirror production technologies based on replication processes, such as cold and hot glass slumping, cured CFRP, and electroforming, provide new opportunities for cost effective solutions for the design of the optical system. We explore capabilities of these mirror fabrication methods for the AGIS project and alignment methods for optical systems. We also study a mechanical structure which will provide support points for mirrors and camera design driven by the requirement of minimizing the deflections of the mirror support structures.

KSC-2011-8115

NASA Image and Video Library

2011-12-01

CAPE CANAVERAL, Fla. -- This is an artist's conception of the Space Vehicle under development by Blue Origin of Kent, Wash., for NASA's Commercial Crew Program (CCP). In 2011, NASA selected Blue Origin during Commercial Crew Development Round 2 (CCDev2) activities to mature the design and development of a crew transportation system with the overall goal of accelerating a United States-led capability to the International Space Station. The goal of CCP is to drive down the cost of space travel as well as open up space to more people than ever before by balancing industry’s own innovative capabilities with NASA's 50 years of human spaceflight experience. Six other aerospace companies also are maturing launch vehicle and spacecraft designs under CCDev2, including Alliant Techsystems Inc. (ATK), The Boeing Co., Excalibur Almaz Inc., Sierra Nevada Corp., Space Exploration Technologies (SpaceX), and United Launch Alliance (ULA). For more information, visit www.nasa.gov/commercialcrew. Image credit: Blue Origin

Interactive Design and Visualization of Branched Covering Spaces.

PubMed

Roy, Lawrence; Kumar, Prashant; Golbabaei, Sanaz; Zhang, Yue; Zhang, Eugene

2018-01-01

Branched covering spaces are a mathematical concept which originates from complex analysis and topology and has applications in tensor field topology and geometry remeshing. Given a manifold surface and an -way rotational symmetry field, a branched covering space is a manifold surface that has an -to-1 map to the original surface except at the ramification points, which correspond to the singularities in the rotational symmetry field. Understanding the notion and mathematical properties of branched covering spaces is important to researchers in tensor field visualization and geometry processing, and their application areas. In this paper, we provide a framework to interactively design and visualize the branched covering space (BCS) of an input mesh surface and a rotational symmetry field defined on it. In our framework, the user can visualize not only the BCSs but also their construction process. In addition, our system allows the user to design the geometric realization of the BCS using mesh deformation techniques as well as connecting tubes. This enables the user to verify important facts about BCSs such as that they are manifold surfaces around singularities, as well as the Riemann-Hurwitz formula which relates the Euler characteristic of the BCS to that of the original mesh. Our system is evaluated by student researchers in scientific visualization and geometry processing as well as faculty members in mathematics at our university who teach topology. We include their evaluations and feedback in the paper.

The Advanced Gamma-ray Imaging System (AGIS): Telescope Optical System Designs

NASA Astrophysics Data System (ADS)

Vassiliev, Vladimir; Buckley, Jim; Falcone, Abe; Fegan, Steven; Finley, John; Gaurino, Victor; Hanna, David; Kaaret, Philip; Konopelko, Alex; Krawczynski, Henric; Romani, Roger; Weekes, Trevor

2008-04-01

AGIS is a conceptual design for a future ground-based gamma-ray observatory based on an array of ˜100 imaging atmospheric Cherenkov telescopes (IACTs) with a sensitivity to gamma-rays in the energy range 40 GeV-100 TeV. The anticipated improvement of AGIS sensitivity, angular resolution, and reliability of operation imposes demanding technological and cost requirements on the design of the IACTs. In this submission we focus on the optical system (OS) of the AGIS telescopes and consider options which include traditional Davies-Cotton and the other prime- focus telescope designs, as well as a novel two-mirror aplanatic OS originally proposed by Schwarzschild. Emerging new mirror production technologies based on replication processes such as cold and hot glass slumping, cured CFRP, and electroforming provide new opportunities for cost effective solutions for the design of the OS. We evaluate the capabilities of these mirror fabrication methods for the AGIS project.

Second-Order Consensus in Multiagent Systems via Distributed Sliding Mode Control.

PubMed

Yu, Wenwu; Wang, He; Cheng, Fei; Yu, Xinghuo; Wen, Guanghui

2016-11-22

In this paper, the new decoupled distributed sliding-mode control (DSMC) is first proposed for second-order consensus in multiagent systems, which finally solves the fundamental unknown problem for sliding-mode control (SMC) design of coupled networked systems. A distributed full-order sliding-mode surface is designed based on the homogeneity with dilation for reaching second-order consensus in multiagent systems, under which the sliding-mode states are decoupled. Then, the SMC is applied to the decoupled sliding-mode states to reach their origin in finite time, which is the sliding-mode surface. The states of agents can first reach the designed sliding-mode surface in finite time and then move to the second-order consensus state along the surface in finite time as well. The DSMC designed in this paper can eliminate the influence of singularity problems and weaken the influence of chattering, which is still very difficult in the SMC systems. In addition, DSMC proposes a general decoupling framework for designing SMC in networked multiagent systems. Simulations are presented to verify the theoretical results in this paper.

Commissioning of the Liquid Nitrogen Thermo-Siphon System for NASA-JSC Chamber A

NASA Technical Reports Server (NTRS)

Homan, J.; Montz, M.; Ganni, V.; Sidi-Yekhlef, A.; Knudsen, P.; Garcia, S.; Garza, J.

2013-01-01

NASA s Space Environment Simulation Laboratory s (SESL) Chamber A, located at the Johnson Space Center in Houston Texas has recently implemented major enhancements of its cryogenic and vacuum systems. The new liquid nitrogen (LN) thermo-siphon system was successfully commissioned in August of 2012. Chamber A, which has 20 K helium cryo-panels (or shrouds ) which are shielded by 80 K nitrogen shrouds, is capable of simulating a deep space environment necessary to perform ground testing of NASA s James Webb Space Telescope (JWST). Chamber A s previous system used forced flow LN cooling with centrifugal pumps, requiring 220,000 liters of LN to cool-down and consuming 180,000 liters per day of LN in steady operation. The LN system did not have the reliability required to meet the long duration test of the JWST, and the cost estimate provided in the initial approach to NASA-JSC by the subcontractor for refurbishment of the system to meet the reliability goals was prohibitive. At NASA-JSC s request, the JLab Cryogenics Group provided alternative options in 2007, including a thermo-siphon, or natural flow system. This system, eliminated the need for pumps and used one tenth of the original control valves, relief valves, and burst disks. After the thermo-siphon approach was selected, JLab provided technical assistance in the process design, mechanical design, component specification development and commissioning oversight, while the installation and commissioning operations of the system was overseen by the Jacobs Technology/ESC group at JSC. The preliminary commissioning data indicate lower shroud temperatures, 68,000 liters to cool-down and less than 91,000 liters per day consumed in steady operation. All of the performance capabilities have exceeded the design goals. This paper will outline the comparison between the original system and the predicted results of the selected design option, and the commissioning results of thermo-siphon system.

Commissioning of the Liquid Nitrogen Thermo-Siphon System for NASA-JSC Chamber-A

NASA Technical Reports Server (NTRS)

Homan, J.; Montz, M.; Ganni, V.; Sidi-Yekhlef, A.; Knudsen, P.; Garcia, S.; Garza, J.

2013-01-01

NASA's Space Environment Simulation Laboratory's (SESL) Chamber A, located at the Johnson Space Center in Houston Texas has recently implemented major enhancements of its cryogenic and vacuum systems. The new liquid nitrogen (LN2) thermo-siphon system was successfully commissioned in August of 2012. Chamber A, which has 20 K helium cryo-panels (or shrouds ) which are shielded by 80 K nitrogen shrouds, is capable of simulating a deep space environment necessary to perform ground testing of NASA s James Webb Space Telescope (JWST). Chamber A s previous system used forced flow LN2 cooling with centrifugal pumps, requiring 200,000 liters of LN2 to cool-down and consuming 180,000 liters per day of LN2 in steady operation. The LN2 system did not have the reliability required to meet the long duration test of the JWST, and the cost estimate provided in the initial approach to NASA-JSC by the sub-contractor for refurbishment of the system to meet the reliability goals was prohibitive. At NASA-JSC's request, the JLab Cryogenics Group provided alternative options in 2007, including a thermo-siphon, or natural flow system. This system, eliminated the need for pumps and used one tenth of the original control valves, relief valves, and burst disks. After the thermo-siphon approach was selected, JLab provided technical assistance in the process design, mechanical design, component specification development and commissioning oversight, while the installation and commissioning operations of the system was overseen by the Jacobs Technology/ESC group at JSC. The preliminary commissioning data indicate lower shroud temperatures, 70,000 liters to cool-down and less than 90,000 liters per day consumed in steady operation. All of the performance capabilities have exceeded the design goals. This paper will outline the comparison between the original system and the predicted results of the selected design option, and the commissioning results of thermo-siphon system.

Transformational Systems Concepts and Technologies for Our Future in Space

NASA Technical Reports Server (NTRS)

Howell, J. T.; George,P.; Mankins, J. C. (Editor); Christensen, C. B.

2004-01-01

NASA is constantly searching for new ideas and approaches yielding opportunities for assuring maximum returns on space infrastructure investments. Perhaps the idea of transformational innovation in developing space systems is long overdue. However, the concept of utilizing modular space system designs combined with stepping-stone development processes has merit and promises to return several times the original investment since each new space system or component is not treated as a unique and/or discrete design and development challenge. New space systems can be planned and designed so that each builds on the technology of previous systems and provides capabilities to support future advanced systems. Subsystems can be designed to use common modular components and achieve economies of scale, production, and operation. Standards, interoperability, and "plug and play" capabilities, when implemented vigorously and consistently, will result in systems that can be upgraded effectively with new technologies. This workshop explored many building-block approaches via way of example across a broad spectrum of technology discipline areas for potentially transforming space systems and inspiring future innovation. Details describing the workshop structure, process, and results are contained in this Conference Publication.

Derate Mitigation Options for Pulverized Coal Power Plant Carbon Capture Retrofits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffmann, Jeffrey W.; Hackett, Gregory A.; Lewis, Eric G.

Carbon capture and storage (CCS) technologies available in the near-term for pulverized coal-fueled power plants (i.e., post combustion solvent technologies) require substantial capital investment and result in marked decrease in electricity available for sale to the grid. The impact to overall plant economics can be mitigated for new plant designs (where the entire plant can be optimized around the CCS system). However, existing coal-fueled power plants were designed without the knowledge or intent to retrofit a CCS process, and it is simply not possible to re-engineer an existing plant in a manner that it could achieve the same performance asmore » if it was originally designed and optimized for CCS technology. Pairing an auxiliary steam supply to the capture system is a technically feasible option to mitigate the derate resulting from diverting steam away from an existing steam turbine and continuing to run that turbine at steam flow rates and properties outside of the original design specifications. The results of this analysis strongly support the merits of meeting the steam and power requirements for a retrofitted post-combustion solvent based carbon dioxide (CO2) capture system with an auxiliary combined heat and power (CHP) plant rather than robbing the base plant (i.e., diverting steam from the existing steam cycle and electricity from sale to the grid).« less

Control console replacement at the WPI Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-01-01

With partial funding from the Department of Energy (DOE) University Reactor Instrumentation Upgrade Program (DOE Grant No. DE-FG02-90ER12982), the original control console at the Worcester Polytechnic Institute (WPI) Reactor has been replaced with a modern system. The new console maintains the original design bases and functionality while utilizing current technology. An advanced remote monitoring system has been added to augment the educational capabilities of the reactor. Designed and built by General Electric in 1959, the open pool nuclear training reactor at WPI was one of the first such facilities in the nation located on a university campus. Devoted to undergraduatemore » use, the reactor and its related facilities have been since used to train two generations of nuclear engineers and scientists for the nuclear industry. The reactor power level was upgraded from 1 to 10 kill in 1969, and its operating license was renewed for 20 years in 1983. In 1988, the reactor was converted to low enriched uranium. The low power output of the reactor and ergonomic facility design make it an ideal tool for undergraduate nuclear engineering education and other training.« less

Thematic mapper critical elements breadboard program

NASA Technical Reports Server (NTRS)

Dale, C. H., Jr.; Engel, J. L.; Harney, E. D.

1976-01-01

A 40.6 cm bidirectional scan mirror assembly, a scan line corrector and a silicon photodiode array with integral preamplifier input stages were designed, fabricated, and tested to demonstrate performance consistent with requirements of the Hughes thematic mapper system. The measured performance met or exceeded the original design goals in all cases with the qualification that well defined and well understood deficiencies in the design of the photodiode array package will require the prescribed corrections before flight use.

Utilization of simulation tools in the HL-20 conceptual design process. [passenger-carrying lifting body portion of Personnel Launch System

NASA Technical Reports Server (NTRS)

Jackson, E. B.; Powell, Richard W.; Ragsdale, W. A.

1991-01-01

The role of simulations in the design of the HL-20, the crew-carrying unpowered lifting-body component of the NASA Personnel Launch System, is reviewed and illustrated with drawings and diagrams. Detailed consideration is given to the overall implementation of a real-time simulation of the HL-20 approach and landing phase, the baseline and experimental control laws used in the flight-control system, autoland guidance and control laws (vertical and lateral steering), the control-surface mixer and actuator model, and simulation results. The simulations allowed identification and correction of design problems with respect to the position of the landing gear and the original maximum L/D ratio of 3.2.

Biosequence Similarity Search on the Mercury System

PubMed Central

Krishnamurthy, Praveen; Buhler, Jeremy; Chamberlain, Roger; Franklin, Mark; Gyang, Kwame; Jacob, Arpith; Lancaster, Joseph

2007-01-01

Biosequence similarity search is an important application in modern molecular biology. Search algorithms aim to identify sets of sequences whose extensional similarity suggests a common evolutionary origin or function. The most widely used similarity search tool for biosequences is BLAST, a program designed to compare query sequences to a database. Here, we present the design of BLASTN, the version of BLAST that searches DNA sequences, on the Mercury system, an architecture that supports high-volume, high-throughput data movement off a data store and into reconfigurable hardware. An important component of application deployment on the Mercury system is the functional decomposition of the application onto both the reconfigurable hardware and the traditional processor. Both the Mercury BLASTN application design and its performance analysis are described. PMID:18846267

Reduction of Martian Sample Return Mission Launch Mass with Solar Sail Propulsion

NASA Technical Reports Server (NTRS)

Russell, Tiffany E.; Heaton, Andy F.; Young, Roy; Baysinger, Mike; Schnell, Andrew R.

2013-01-01

Solar sails have the potential to provide mass and cost savings for spacecraft traveling within the innter solar system. Companies like L'Garde have demonstrated sail manufacturability and various i-space development methods. The purpose of this study was to evaluate a current Mars sample return architecture and to determine how cost and mass would be reduced by incorporating a solar sail propulsion system. The team validated the design proposed by L'Garde, and scaled the design based on a trajectory analysis. Using the solar sail design reduced the required mass, eliminating one of the three launches required in the original architecture.

Reduction of Martian Sample Return Mission Launch Mass with Solar Sail Propulsion

NASA Technical Reports Server (NTRS)

Russell, Tiffany E.; Heaton, Andrew; Thomas, Scott; Thomas, Dan; Young, Roy; Baysinger, Mike; Capizzo, Pete; Fabisinski, Leo; Hornsby, Linda; Maples, Dauphne;

The state of the Java universe

ScienceCinema

Gosling, James

2018-05-22

Speaker Bio: James Gosling received a B.Sc. in computer science from the University of Calgary, Canada in 1977. He received a Ph.D. in computer science from Carnegie-Mellon University in 1983. The title of his thesis was The Algebraic Manipulation of Constraints. He has built satellite data acquisition systems, a multiprocessor version of UNIX®, several compilers, mail systems, and window managers. He has also built a WYSIWYG text editor, a constraint-based drawing editor, and a text editor called Emacs, for UNIX systems. At Sun his early activity was as lead engineer of the NeWS window system. He did the original design of the Java programming language and implemented its original compiler and virtual machine. He has recently been a contributor to the Real-Time Specification for Java.

Network, system, and status software enhancements for the autonomously managed electrical power system breadboard. Volume 1: Project summary

NASA Technical Reports Server (NTRS)

Mckee, James W.

1990-01-01

This volume (1 of 4) gives a summary of the original AMPS software system configuration, points out some of the problem areas in the original software design that this project is to address, and in the appendix collects all the bimonthly status reports. The purpose of AMPS is to provide a self reliant system to control the generation and distribution of power in the space station. The software in the AMPS breadboard can be divided into three levels: the operating environment software, the protocol software, and the station specific software. This project deals only with the operating environment software and the protocol software. The present station specific software will not change except as necessary to conform to new data formats.

Dossier of Evaluation Instruments for Literacy Programmes. A Contribution to the International Literacy Year 1990.

ERIC Educational Resources Information Center

Muller, Josef, Ed.; Dietrich, Anja, Ed.

This document contains a collection of literacy program evaluation instruments from developing countries, as well as several papers describing how to use evaluation instruments to assess various types of systems. The following titles (with author or country of origin) are contained in this collection: "Designing a System of Evaluation and…

Program: A Record of the First 40 Years of Electronic Library and Information Systems

ERIC Educational Resources Information Center

Tedd, Lucy A.

2006-01-01

Purpose: To provide a broad overview of the history of the journal Program: electronic library and information systems and its contents over its first 40 years. Design/methodology/approach: Analysis of content from the original published material, as well as from abstracting and indexing publications and from minutes of Editorial Board meetings.…

Applying Cognitive Load Theory to the Redesign of a Conventional Database Systems Course

ERIC Educational Resources Information Center

Mason, Raina; Seton, Carolyn; Cooper, Graham

2016-01-01

Cognitive load theory (CLT) was used to redesign a Database Systems course for Information Technology students. The redesign was intended to address poor student performance and low satisfaction, and to provide a more relevant foundation in database design and use for subsequent studies and industry. The original course followed the conventional…

Lockheed L-1101 avionic flight control redundant systems

NASA Technical Reports Server (NTRS)

Throndsen, E. O.

1976-01-01

The Lockheed L-1011 automatic flight control systems - yaw stability augmentation and automatic landing - are described in terms of their redundancies. The reliability objectives for these systems are discussed and related to in-service experience. In general, the availability of the stability augmentation system is higher than the original design requirement, but is commensurate with early estimates. The in-service experience with automatic landing is not sufficient to provide verification of Category 3 automatic landing system estimated availability.

Analyzing Robotic Kinematics Via Computed Simulations

NASA Technical Reports Server (NTRS)

Carnahan, Timothy M.

1992-01-01

Computing system assists in evaluation of kinematics of conceptual robot. Displays positions and motions of robotic manipulator within work cell. Also displays interactions between robotic manipulator and other objects. Results of simulation displayed on graphical computer workstation. System includes both off-the-shelf software originally developed for automotive industry and specially developed software. Simulation system also used to design human-equivalent hand, to model optical train in infrared system, and to develop graphical interface for teleoperator simulation system.

Cloning systems for Rhodococcus and related bacteria

DOEpatents

Finnerty, W.R.; Singer, M.E.

1990-08-28

A plasmid transformation system for Rhodococcus was developed using an Escherichia coli-Rhodococcus shuttle plasmid. Rhodococcus sp. H13-A contains three cryptic indigenous plasmids, designated pMVS100, pMVS200 and pMVS300, of 75, 19.5 and 13.4 kilobases (Kb), respectively. A 3.8 Kb restriction fragment of pMVS300 was cloned into pIJ30, a 6.3 Kb pBR322 derivative, containing the E. coli origin of replication (ori) and ampicillin resistance determinant (bla) as well as a Streptomyces gene for thiostrepton resistance, tsr. The resulting 10.1 Kb recombinant plasmid, designated pMVS301, was isolated from E. coli DH1 (pMVS301) and transformed into Rhodococcus sp. AS-50, a derivative of strain H13-A, by polyethylene glycol-assisted transformation of Rhodococcus protoplasts and selection for thiostrepton-resistant transformants. This strain was deposited with the ATCC on Feb. 1, 1988 and assigned ATCC 53719. The plasmid contains the Rhodococcus origin of replication. The plasmid and derivatives thereof can therefore be used to introduce nucleic acid sequences to and from Rhodococcus for subsequent expression and translation into protein. The isolated origin of replication can also be used in the construction of new vectors. 2 figs.

Cloning systems for Rhodococcus and related bacteria

DOEpatents

Finnerty, William R.; Singer, Mary E.

1990-01-01

A plasmid transformation system for Rhodococcus was developed using an Escherichia coli-Rhodococcus shuttle plasmid. Rhodococcus sp. H13-A contains three cryptic indigenous plasmids, designated pMVS100, pMVS200 and pMVS300, of 75, 19.5 and 13.4 kilobases (Kb), respectively. A 3.8 Kb restriction fragment of pMVS300 was cloned into pIJ30, a 6.3 Kb pBR322 derivative, containing the E. coli origin of replication (ori) and ampicillin resistance determinant (bla) as well as a Streptomyces gene for thiostrepton resistance, tsr. The resulting 10.1 Kb recombinant plasmid, designated pMVS301, was isolated from E. coli DH1 (pMVS301) and transformed into Rhodococcus sp. AS-50, a derivative of strain H13-A, by polyethylene glycol-assisted transformation of Rhodococcus protoplasts and selection for thiostrepton-resistant transformants. This strain was deposited with the ATCC on Feb. 1, 1988 and assigned ATCC 53719. The plasmid contains the Rhodococcus origin of replication. The plasmid and derivatives thereof can therefore be used to introduce nucleic acid sequences to and from Rhodococcus for subsequent expression and translation into protein. The isolated origin of replication can also be used in the construction of new vectors.

Material Testing Device

NASA Technical Reports Server (NTRS)

1993-01-01

Small Business Innovation Research (SBIR) contracts led to two commercial instruments and a new subsidiary for Physical Sciences, Inc. (PSI). The FAST system, originally developed for testing the effect of space environment on materials, is now sold commercially for use in aging certification of materials intended for orbital operation. The Optical Temperature Monitor was designed for precise measurement of high temperatures on certain materials to be manufactured in space. The original research was extended to the development of a commercial instrument that measures and controls fuel gas temperatures in industrial boilers. PSI created PSI Environmental Instruments to market the system. The company also offers an Aerospace Measurement Service that has evolved from other SBIR contracts.

Stability of multiloop LQ regulators with nonlinearities. I - Regions of attraction. II - Regions of ultimate boundedness

NASA Technical Reports Server (NTRS)

Joshi, S. M.

1986-01-01

An investigation is conducted for the closed loop stability of linear time-invariant systems controlled by linear quadratic (LQ) regulators, in cases where nonlinearities exist in the control channels lying outside the stability sector in regions away from the origin. The estimate of the region of attraction thus obtained furnishes methods for the selection of performance function weights for more robust LQ designs. Attention is then given to the closed loop stability of linear time-invariant systems controlled by the LQ regulators when the nonlinearities in the loops escape the stability sector in a bounded region containing the origin.

Update on optical design of adaptive optics system at Lick Observatory

NASA Astrophysics Data System (ADS)

Bauman, Brian J.; Gavel, Donald T.; Waltjen, Kenneth E.; Freeze, Gary J.; Hurd, Randall L.; Gates, Elinor L.; Max, Claire E.; Olivier, Scot S.; Pennington, Deanna M.

2002-02-01

In 1999, we presented our plan to upgrade the adaptive optics (AO) system on the Lick Observatory Shane telescope (3m) from a prototype instrument pressed into field service to a facility instrument. This paper updates the progress of that plan and details several important improvements in the alignment and calibration of the AO bench. The paper also includes a discussion of the problems seen in the original design of the tip/tilt (t/t) sensor used in laser guide star mode, and how these problems were corrected with excellent results.

Common approach to solving SGEMP, DEMP, and ESD survivability

NASA Technical Reports Server (NTRS)

Ling, D.

1977-01-01

System Generated Electromagnetic Pulse (SGEMP) and Dispersed Electromagnetic Pulse DEMP) are nuclear generated spacecraft environments. Electrostatic discharge (ESD) is a natural spacecraft environment resulting from differential charging in magnetic substorms. All three phenomena, though differing in origin, result in the same problem to the spacecraft and that is Electromagnetic Interference (EMI). A common design approach utilizing a spacecraft structural Faraday Cage is presented which helps solve the EMI problem. Also, other system design techniques are discussed which minimize the magnitude of these environments through control of materials and electrical grounding configuration.

The measurement of the earth's radiation budget as a problem in information theory - A tool for the rational design of earth observing systems

NASA Technical Reports Server (NTRS)

Barkstrom, B. R.

1983-01-01

The measurement of the earth's radiation budget has been chosen to illustrate the technique of objective system design. The measurement process is an approximately linear transformation of the original field of radiant exitances, so that linear statistical techniques may be employed. The combination of variability, measurement strategy, and error propagation is presently made with the help of information theory, as suggested by Kondratyev et al. (1975) and Peckham (1974). Covariance matrices furnish the quantitative statement of field variability.

Update on Optical Design of Adaptive Optics System at Lick Observatory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauman, B J; Gavel, D T; Waltjen, K E

2001-07-31

In 1999, we presented our plan to upgrade the adaptive optics (AO) system on the Lick Observatory Shane telescope (3m) from a prototype instrument pressed into field service to a facility instrument. This paper updates the progress of that plan and details several important improvements in the alignment and calibration of the AO bench. The paper also includes a discussion of the problems seen in the original design of the tip/tilt (t/t) sensor used in laser guide star mode, and how these problems were corrected with excellent results.

Redesigning a risk-management process for tracking injuries.

PubMed

Wenzel, G R

1998-01-01

The changing responsibilities of registered nurses are challenging even the most dedicated professionals. To survive within her newly-defined roles, one nurse used a total quality improvement model to understand, analyze, and improve a medical center's system for tracking inpatient injuries. This process led to the drafting of an original software design that implemented a nursing informatics tracking system. It has resulted in significant savings of time and money and has far surpassed the accuracy, efficiency, and scope of the previous method. This article presents an overview of the design process.

Lunar lander ground support system

NASA Technical Reports Server (NTRS)

1991-01-01

The design of the Lunar Lander Ground Support System (LLGSS) is examined. The basic design time line is around 2010 to 2030 and is referred to as a second generation system, as lunar bases and equipment would have been present. Present plans for lunar colonization call for a phased return of personnel and materials to the moons's surface. During settlement of lunar bases, the lunar lander is stationary in a very hostile environment and would have to be in a state of readiness for use in case of an emergency. Cargo and personnel would have to be removed from the lander and transported to a safe environment at the lunar base. An integrated system is required to perform these functions. These needs are addressed which center around the design of a lunar lander servicing system. The servicing system could perform several servicing functions to the lander in addition to cargo servicing. The following were considered: (1) reliquify hydrogen boiloff; (2) supply power; and (3) remove or add heat as necessary. The final design incorporates both original designs and existing vehicles and equipment on the surface of the moon at the time considered. The importance of commonality is foremost in the design of any lunar machinery.

Overview of field gamma spectrometries based on Si-photomultiplier

NASA Astrophysics Data System (ADS)

Denisov, Viktor; Korotaev, Valery; Titov, Aleksandr; Blokhina, Anastasia; Kleshchenok, Maksim

2017-05-01

Design of optical-electronic devices and systems involves the selection of such technical patterns that under given initial requirements and conditions are optimal according to certain criteria. The original characteristic of the OES for any purpose, defining its most important feature ability is a threshold detection. Based on this property, will be achieved the required functional quality of the device or system. Therefore, the original criteria and optimization methods have to subordinate to the idea of a better detectability. Generally reduces to the problem of optimal selection of the expected (predetermined) signals in the predetermined observation conditions. Thus the main purpose of optimization of the system when calculating its detectability is the choice of circuits and components that provide the most effective selection of a target.

The implementation and use of Ada on distributed systems with high reliability requirements

NASA Technical Reports Server (NTRS)

Knight, J. C.

1988-01-01

The use and implementation of Ada were investigated in distributed environments in which reliability is the primary concern. In particular, the focus was on the possibility that a distributed system may be programmed entirely in Ada so that the individual tasks of the system are unconcerned with which processors are being executed, and that failures may occur in the software and underlying hardware. A secondary interest is in the performance of Ada systems and how that performance can be gauged reliably. Primary activities included: analysis of the original approach to recovery in distributed Ada programs using the Advanced Transport Operating System (ATOPS) example; review and assessment of the original approach which was found to be capable of improvement; development of a refined approach to recovery that was applied to the ATOPS example; and design and development of a performance assessment scheme for Ada programs based on a flexible user-driven benchmarking system.

Extended cooperative control synthesis

NASA Technical Reports Server (NTRS)

Davidson, John B.; Schmidt, David K.

1994-01-01

This paper reports on research for extending the Cooperative Control Synthesis methodology to include a more accurate modeling of the pilot's controller dynamics. Cooperative Control Synthesis (CCS) is a methodology that addresses the problem of how to design control laws for piloted, high-order, multivariate systems and/or non-conventional dynamic configurations in the absence of flying qualities specifications. This is accomplished by emphasizing the parallel structure inherent in any pilot-controlled, augmented vehicle. The original CCS methodology is extended to include the Modified Optimal Control Model (MOCM), which is based upon the optimal control model of the human operator developed by Kleinman, Baron, and Levison in 1970. This model provides a modeling of the pilot's compensation dynamics that is more accurate than the simplified pilot dynamic representation currently in the CCS methodology. Inclusion of the MOCM into the CCS also enables the modeling of pilot-observation perception thresholds and pilot-observation attention allocation affects. This Extended Cooperative Control Synthesis (ECCS) allows for the direct calculation of pilot and system open- and closed-loop transfer functions in pole/zero form and is readily implemented in current software capable of analysis and design for dynamic systems. Example results based upon synthesizing an augmentation control law for an acceleration command system in a compensatory tracking task using the ECCS are compared with a similar synthesis performed by using the original CCS methodology. The ECCS is shown to provide augmentation control laws that yield more favorable, predicted closed-loop flying qualities and tracking performance than those synthesized using the original CCS methodology.

High Energy Astronomy Observatory (HEAO)

NASA Image and Video Library

1977-01-01

This photograph shows the High Energy Astronomy Observatory (HEAO)-1 being assembled at TRW Systems of Redondo Beach, California. The HEAO was designed and developed by TRW, Inc. under the project management of the Marshall Space Flight Center. The first observatory, designated HEAO-1, was launched on August 12, 1977 aboard an Atlas/Centaur launch vehicle and was designed to survey the sky for additional x-ray and gamma-ray sources as well as pinpointing their positions. The HEAO-1 was originally identified as HEAO-A but the designation was changed once the spacecraft achieved orbit.

Preliminary Results on Luminaire Designs for Hybrid Solar Lighting Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Earl, D.D.

2001-06-15

We report on the design of two hybrid lighting luminaires that blend light from a fiber optic end-emitted solar source with electric T8 fluorescent lamps. Both designs involve the retrofit of a commercially-available recessed fluorescent luminaire with minimal reductions in the original luminaire's optical efficiency. Two methods for high-angle dispersion of fiber optic end-emitted solar light are described and the resulting spatial intensity distributions, simulated using ZEMAX, are compared with standard cylindrical fluorescent tubes. Differences in spatial intensity distribution are qualitatively characterized and potential design improvements discussed.

Smoke Detection for the Orion Crew Exploration Vehicle

NASA Technical Reports Server (NTRS)

Sutin, Brian M.; Niu, William; Steiner, George; O'Hara, William; Lewis, John F.

2009-01-01

The Orion Crew Exploration Vehicle (CEV) requires a smoke detector for the detection of particulate smoke products as part of the Fire Detection and Suppression (FDS) system. The smoke detector described in this paper is an adaptation of a mature commercial aircraft design for manned spaceflight. Changes made to the original design include upgrading the materials and electronic to space-qualified parts, and modifying the mechanical design to withstand launch and landing loads. The results of laboratory characterization of the response of the new design to test particles are presented.

Design optimization of large-size format edge-lit light guide units

NASA Astrophysics Data System (ADS)

Hastanin, J.; Lenaerts, C.; Fleury-Frenette, K.

2016-04-01

In this paper, we present an original method of dot pattern generation dedicated to large-size format light guide plate (LGP) design optimization, such as photo-bioreactors, the number of dots greatly exceeds the maximum allowable number of optical objects supported by most common ray-tracing software. In the proposed method, in order to simplify the computational problem, the original optical system is replaced by an equivalent one. Accordingly, an original dot pattern is splitted into multiple small sections, inside which the dot size variation is less than the ink dots printing typical resolution. Then, these sections are replaced by equivalent cells with continuous diffusing film. After that, we adjust the TIS (Total Integrated Scatter) two-dimensional distribution over the grid of equivalent cells, using an iterative optimization procedure. Finally, the obtained optimal TIS distribution is converted into the dot size distribution by applying an appropriate conversion rule. An original semi-empirical equation dedicated to rectangular large-size LGPs is proposed for the initial guess of TIS distribution. It allows significantly reduce the total time needed to dot pattern optimization.

Structures and mechanisms - Streamlining for fuel economy

NASA Technical Reports Server (NTRS)

Card, M. F.

1983-01-01

The design of prospective NASA space station components which inherently possess the means for structural growth without compromising initial system characteristics is considered. In structural design terms, space station growth can be achieved by increasing design safety factors, introducing dynamic isolators to prevent loads from reaching the initial components, or preplanning the refurbishment of the original structure with stronger elements. Design tradeoffs will be based on the definition of on-orbit loads, including docking and maneuvering, whose derived load spectra will allow the estimation of fatigue life. Improvements must be made in structural materials selection in order to reduce contamination, slow degradation, and extend the life of coatings. To minimize on-orbit maintenance, long service life lubrication systems with advanced sealing devices must be developed.

The ADVANCE project : formal evaluation of the targeted deployment. Volume 1

DOT National Transportation Integrated Search

1997-01-01

The Advanced Driver and Vehicle Advisory Navigation ConcEpt (ADVANCE) was an in-vehicle advanced traveler information system (ATIS) that operated in the northwest suburbs of Chicago, Illinois. It was designed to provide origin-destination shortest-ti...

CHAMELEON AUTOMATED RESIDENTIAL ENERGY MANAGEMENT SYSTEM

EPA Science Inventory

The expected output of the project will be an experimentally determined Chameleon specification. The expected outcomes will include 1) a set of guidelines for implementing Chameleon in residential structures from both a retrofit and original design perspective and 2) a cost a...

Application of color to reduce complexity in air traffic control.

DOT National Transportation Integrated Search

2002-11-01

The United States Air Traffic Control (ATC) system is designed to provide for the safe and efficient flow of air : traffic from origin to destination. The Federal Aviation Administration predicts that traffic levels will continue : increasing over th...

Expert System Software

NASA Technical Reports Server (NTRS)

1989-01-01

C Language Integrated Production System (CLIPS) is a software shell for developing expert systems is designed to allow research and development of artificial intelligence on conventional computers. Originally developed by Johnson Space Center, it enables highly efficient pattern matching. A collection of conditions and actions to be taken if the conditions are met is built into a rule network. Additional pertinent facts are matched to the rule network. Using the program, E.I. DuPont de Nemours & Co. is monitoring chemical production machines; California Polytechnic State University is investigating artificial intelligence in computer aided design; Mentor Graphics has built a new Circuit Synthesis system, and Brooke and Brooke, a law firm, can determine which facts from a file are most important.

Anticontrol of chaos in continuous-time systems via time-delay feedback.

PubMed

Wang, Xiao Fan; Chen, Guanrong; Yu, Xinghuo

2000-12-01

In this paper, a systematic design approach based on time-delay feedback is developed for anticontrol of chaos in a continuous-time system. This anticontrol method can drive a finite-dimensional, continuous-time, autonomous system from nonchaotic to chaotic, and can also enhance the existing chaos of an originally chaotic system. Asymptotic analysis is used to establish an approximate relationship between a time-delay differential equation and a discrete map. Anticontrol of chaos is then accomplished based on this relationship and the differential-geometry control theory. Several examples are given to verify the effectiveness of the methodology and to illustrate the systematic design procedure. (c) 2000 American Institute of Physics.

A PC-based multispectral scanner data evaluation workstation: Application to Daedalus scanners

NASA Technical Reports Server (NTRS)

Jedlovec, Gary J.; James, Mark W.; Smith, Matthew R.; Atkinson, Robert J.

1991-01-01

In late 1989, a personal computer (PC)-based data evaluation workstation was developed to support post flight processing of Multispectral Atmospheric Mapping Sensor (MAMS) data. The MAMS Quick View System (QVS) is an image analysis and display system designed to provide the capability to evaluate Daedalus scanner data immediately after an aircraft flight. Even in its original form, the QVS offered the portability of a personal computer with the advanced analysis and display features of a mainframe image analysis system. It was recognized, however, that the original QVS had its limitations, both in speed and processing of MAMS data. Recent efforts are presented that focus on overcoming earlier limitations and adapting the system to a new data tape structure. In doing so, the enhanced Quick View System (QVS2) will accommodate data from any of the four spectrometers used with the Daedalus scanner on the NASA ER2 platform. The QVS2 is designed around the AST 486/33 MHz CPU personal computer and comes with 10 EISA expansion slots, keyboard, and 4.0 mbytes of memory. Specialized PC-McIDAS software provides the main image analysis and display capability for the system. Image analysis and display of the digital scanner data is accomplished with PC-McIDAS software.

Reengineering a database for clinical trials management: lessons for system architects.

PubMed

Brandt, C A; Nadkarni, P; Marenco, L; Karras, B T; Lu, C; Schacter, L; Fisk, J M; Miller, P L

2000-10-01

This paper describes the process of enhancing Trial/DB, a database system for clinical studies management. The system's enhancements have been driven by the need to maximize the effectiveness of developer personnel in supporting numerous and diverse users, of study designers in setting up new studies, and of administrators in managing ongoing studies. Trial/DB was originally designed to work over a local area network within a single institution, and basic architectural changes were necessary to make it work over the Internet efficiently as well as securely. Further, as its use spread to diverse communities of users, changes were made to let the processes of study design and project management adapt to the working styles of the principal investigators and administrators for each study. The lessons learned in the process should prove instructive for system architects as well as managers of electronic patient record systems.

Dynamic analysis, circuit implementation and passive control of a novel four-dimensional chaotic system with multiscroll attractor and multiple coexisting attractors

NASA Astrophysics Data System (ADS)

Lai, Bang-Cheng; He, Jian-Jun

2018-03-01

In this paper, we construct a novel 4D autonomous chaotic system with four cross-product nonlinear terms and five equilibria. The multiple coexisting attractors and the multiscroll attractor of the system are numerically investigated. Research results show that the system has various types of multiple attractors, including three strange attractors with a limit cycle, three limit cycles, two strange attractors with a pair of limit cycles, two coexisting strange attractors. By using the passive control theory, a controller is designed for controlling the chaos of the system. Both analytical and numerical studies verify that the designed controller can suppress chaotic motion and stabilise the system at the origin. Moreover, an electronic circuit is presented for implementing the chaotic system.

Generating multi-double-scroll attractors via nonautonomous approach.

PubMed

Hong, Qinghui; Xie, Qingguo; Shen, Yi; Wang, Xiaoping

2016-08-01

It is a common phenomenon that multi-scroll attractors are realized by introducing the various nonlinear functions with multiple breakpoints in double scroll chaotic systems. Differently, we present a nonautonomous approach for generating multi-double-scroll attractors (MDSA) without changing the original nonlinear functions. By using the multi-level-logic pulse excitation technique in double scroll chaotic systems, MDSA can be generated. A Chua's circuit, a Jerk circuit, and a modified Lorenz system are given as designed example and the Matlab simulation results are presented. Furthermore, the corresponding realization circuits are designed. The Pspice results are in agreement with numerical simulation results, which verify the availability and feasibility of this method.

Prospective communications research to support fly by light/power by wire

NASA Technical Reports Server (NTRS)

Game, David

1994-01-01

A NASA Research Grant NAG-1-1309, Distributed Fiber Optic Systems for Commercial Aircraft, was awarded during July 1991. This report primarily constitutes a summary of findings of the original background research done at that time. NASA is embarking on a research project to design the next generation of commercial aircraft, fly by light/power by wire. The objectives of this effort are to improve commercial aircraft design by (1) reducing the weight of the aircraft to improve efficiency and (2) improving the fault tolerance and safety of the aircraft by enhancing current systems with new technologies or introducing new systems into the aircraft.

Original antigenic sin: A comprehensive review.

PubMed

Vatti, Anup; Monsalve, Diana M; Pacheco, Yovana; Chang, Christopher; Anaya, Juan-Manuel; Gershwin, M Eric

2017-09-01

The concept of "original antigenic sin" was first proposed by Thomas Francis, Jr. in 1960. This phenomenon has the potential to rewrite what we understand about how the immune system responds to infections and its mechanistic implications on how vaccines should be designed. Antigenic sin has been demonstrated to occur in several infectious diseases in both animals and humans, including human influenza infection and dengue fever. The basis of "original antigenic sin" requires immunological memory, and our immune system ability to autocorrect. In the context of viral infections, it is expected that if we are exposed to a native strain of a pathogen, we should be able to mount a secondary immune response on subsequent exposure to the same pathogen. "Original antigenic sin" will not contradict this well-established immunological process, as long as the subsequent infectious antigen is identical to the original one. But "original antigenic sin" implies that when the epitope varies slightly, then the immune system relies on memory of the earlier infection, rather than mount another primary or secondary response to the new epitope which would allow faster and stronger responses. The result is that the immunological response may be inadequate against the new strain, because the immune system does not adapt and instead relies on its memory to mount a response. In the case of vaccines, if we only immunize to a single strain or epitope, and if that strain/epitope changes over time, then the immune system is unable to mount an accurate secondary response. In addition, depending of the first viral exposure the secondary immune response can result in an antibody-dependent enhancement of the disease or at the opposite, it could induce anergy. Both of them triggering loss of pathogen control and inducing aberrant clinical consequences. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cargo Movement Operations System (CMOS): Final Software Design Document, Forms 3.0 Conversion Project, Increment III.

DTIC Science & Technology

1991-09-05

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ 3 ... ... .. . ....... ... .. ............ ... . . . . . . . u m ORIGINATOR CONTROL NUMBER: SDD-0002 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: DCO0-0005d DATE: 09/05/91 ORIGINATOR NAME: Vivian L. Martin OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 271-2999 SUBSTANTIVE: x EDITORIAL: PAGE NUMBER: CUlAO025-3 PARA NUMBER: c. COMMENT OR RECOMMENDED CHANGE: Provide the input, output, and local data elements for this CSU. RATIONALE: Paragraph c. states that data

An Experimental Framework for Generating Evolvable Chemical Systems in the Laboratory

NASA Astrophysics Data System (ADS)

Baum, David A.; Vetsigian, Kalin

2017-12-01

Most experimental work on the origin of life has focused on either characterizing the chemical synthesis of particular biochemicals and their precursors or on designing simple chemical systems that manifest life-like properties such as self-propagation or adaptive evolution. Here we propose a new class of experiments, analogous to artificial ecosystem selection, where we select for spontaneously forming self-propagating chemical assemblages in the lab and then seek evidence of a response to that selection as a key indicator that life-like chemical systems have arisen. Since surfaces and surface metabolism likely played an important role in the origin of life, a key experimental challenge is to find conditions that foster nucleation and spread of chemical consortia on surfaces. We propose high-throughput screening of a diverse set of conditions in order to identify combinations of "food," energy sources, and mineral surfaces that foster the emergence of surface-associated chemical consortia that are capable of adaptive evolution. Identification of such systems would greatly advance our understanding of the emergence of self-propagating entities and the onset of adaptive evolution during the origin of life.

117.6-kilobit telemetry from Mercury in-flight system analysis

NASA Technical Reports Server (NTRS)

Evanchuk, V. L.

1974-01-01

This paper discusses very specifically the mode of the Mariner Venus/Mercury 1973 (MVM'73) telecommunications system in the interplexed dual channel 117.6 kilobits per second (kbps) and 2.45 kbps telemetry. This mode, originally designed for only Venus encounter, was also used at Mercury despite significantly less performance margin. Detailed analysis and careful measurement of system performance before and during flight operations allowed critical operational decisions, which made maximum use of the system capabilities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oppel III, Fred J.; Rigdon, James Brian; Gottlieb, Eric Joseph

This package contains, for the most part, the base classes and interfaces for vehicles and characters. Originally everything was in UGV, but things were split out to simplify the design since the assertion of UGV1.0. Modules in UGV, UWV, and UAV will inherit from classes in this package. There is also a high-level system that is a base class for systems in UGV, UWV, and UAV.

75 FR 38943 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-07

... system, which could cause voltage levels to go beyond original design levels between fuel tank probes and... following methods: Federal eRulemaking Portal: Go to http://www.regulations.gov . Follow the instructions...-induced transients to the fuel quantity indication system, which could cause voltage levels to go beyond...

System design of the Pioneer Venus spacecraft. Volume 14: Test planning trades

NASA Technical Reports Server (NTRS)

Pedretti, C. D.

1973-01-01

Pioneer Venus system test plans and trade studies which were first published as Study Tasks (References 1 through 5) are reviewed. The plan and trade studies are presented in a condensed form. Greater detail may be found in the referenced study tasks if desired. All significant conclusions and plan outlines of the original studies are, presented.

76 FR 4747 - Proposed Collection; Comment Request; Bank Secrecy Act Unified Currency Transaction Report...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-26

... transitions from a system originally designed for collecting paper forms to a modernized IT environment for... of CTRs under the BSA. The CTR will be an e- filed dynamic and interactive report used by all BSA... System of Records Notice relating to BSA Reports.\\3\\ \\3\\ Department of the Treasury bureaus such as Fin...

A Behavioural Approach to Understanding Semi-Subsistence Farmers' Technology Adoption Decisions: The Case of Improved Paddy-Prawn System in Indonesia

ERIC Educational Resources Information Center

Sambodo, Leonardo A. A. T.; Nuthall, Peter L.

2010-01-01

Purpose: This study traced the origins of subsistence Farmers' technology adoption attitudes and extracted the critical elements in their decision making systems. Design/Methodology/Approach: The analysis was structured using a model based on the Theory of Planned Behaviour (TPB). The role of a "bargaining process" was particularly…

Synthesis of Available Research and Databases on the Migrant Education Program. Volume II: the Migrant Student Record Transfer System.

ERIC Educational Resources Information Center

Eckels, Elaine; Vorek, Robert

The Migrant Student Record Transfer System (MSRTS) is a nationwide computer-based communications network originally designed to transfer the health and educational records of migrant workers' children. This report assesses MSRTS data from September 1984 through June 1986 to determine the potential utility of such data for national studies of the…

Effects of different roller/crimper designs and rolling speed on rye cover crop termination and seedcotton yield in A no-till system

USDA-ARS?s Scientific Manuscript database

Rollers/crimpers have been utilized in no-till systems to mechanically terminate cover crops as a substitute for chemical termination; however, excessive vibration generated by the original straight bar roller adopted from Brazil has delayed its adoption in the U.S. To reduce excessive vibration, pr...

Image Processor Electronics (IPE): The High-Performance Computing System for NASA SWIFT Mission

NASA Technical Reports Server (NTRS)

Nguyen, Quang H.; Settles, Beverly A.

2003-01-01

Gamma Ray Bursts (GRBs) are believed to be the most powerful explosions that have occurred in the Universe since the Big Bang and are a mystery to the scientific community. Swift, a NASA mission that includes international participation, was designed and built in preparation for a 2003 launch to help to determine the origin of Gamma Ray Bursts. Locating the position in the sky where a burst originates requires intensive computing, because the duration of a GRB can range between a few milliseconds up to approximately a minute. The instrument data system must constantly accept multiple images representing large regions of the sky that are generated by sixteen gamma ray detectors operating in parallel. It then must process the received images very quickly in order to determine the existence of possible gamma ray bursts and their locations. The high-performance instrument data computing system that accomplishes this is called the Image Processor Electronics (IPE). The IPE was designed, built and tested by NASA Goddard Space Flight Center (GSFC) in order to meet these challenging requirements. The IPE is a small size, low power and high performing computing system for space applications. This paper addresses the system implementation and the system hardware architecture of the IPE. The paper concludes with the IPE system performance that was measured during end-to-end system testing.

PROCESS DESIGN MANUAL: NITROGEN CONTROL

EPA Science Inventory

This manual is an update and revision of the original 1975 edition. Given the experience of the past 18 years, the focus of this edition is directed to those biological/mechanical systems that have found widespread use for nitrification and nitrogen,removal. The primary audience ...

Launch Window Trade Analysis for the James Webb Space Telescope

NASA Technical Reports Server (NTRS)

Yu, Wayne H.; Richon, Karen

2014-01-01

The James Webb Space Telescope (JWST) is a large-scale space telescope mission designed to study fundamental astrophysical questions ranging from the formation of the universe to the origin of planetary systems and the origins of life. JWSTs orbit design is a Libration Point Orbit (LPO) around the Sun-Earth/Moon (SEM) L2 point for a planned mission lifetime of 10.5 years. The launch readiness period for JWST is from Oct 1st, 2018 November 30th, 2018. This paper presents the first launch window analysis for the JWST observatory using finite-burn modeling; previous analysis assumed a single impulsive midcourse correction to achieve the mission orbit. The physical limitations of the JWST hardware stemming primarily from propulsion, communication and thermal requirements alongside updated mission design requirements result in significant launch window within the launch readiness period. Future plans are also discussed.

James Webb Space Telescope Launch Window Trade Analysis

NASA Technical Reports Server (NTRS)

Yu, Wayne; Richon, Karen

2014-01-01

The James Webb Space Telescope (JWST) is a large-scale space telescope mission designed to study fundamental astrophysical questions ranging from the formation of the universe to the origin of planetary systems and the origins of life. JWSTs orbit design is a Libration Point Orbit (LPO) around the Sun-EarthMoon (SEM) L2 point for a planned mission lifetime of 10.5 years. The launch readiness period for JWST is from Oct 1st, 2018 November 30th, 2018. This paper presents the first launch window analysis for the JWST observatory using finite-burn modeling; previous analysis assumed a single impulsive midcourse correction to achieve the mission orbit. The physical limitations of the JWST hardware stemming primarily from propulsion, communication and thermal requirements alongside updated mission design requirements result in significant launch window within the launch readiness period. Future plans are also discussed.

Enzyme-free nucleic acid dynamical systems.

PubMed

Srinivas, Niranjan; Parkin, James; Seelig, Georg; Winfree, Erik; Soloveichik, David

2017-12-15

Chemistries exhibiting complex dynamics-from inorganic oscillators to gene regulatory networks-have been long known but either cannot be reprogrammed at will or rely on the sophisticated enzyme chemistry underlying the central dogma. Can simpler molecular mechanisms, designed from scratch, exhibit the same range of behaviors? Abstract chemical reaction networks have been proposed as a programming language for complex dynamics, along with their systematic implementation using short synthetic DNA molecules. We developed this technology for dynamical systems by identifying critical design principles and codifying them into a compiler automating the design process. Using this approach, we built an oscillator containing only DNA components, establishing that Watson-Crick base-pairing interactions alone suffice for complex chemical dynamics and that autonomous molecular systems can be designed via molecular programming languages. Copyright © 2017 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

A real-time MTFC algorithm of space remote-sensing camera based on FPGA

NASA Astrophysics Data System (ADS)

Zhao, Liting; Huang, Gang; Lin, Zhe

2018-01-01

A real-time MTFC algorithm of space remote-sensing camera based on FPGA was designed. The algorithm can provide real-time image processing to enhance image clarity when the remote-sensing camera running on-orbit. The image restoration algorithm adopted modular design. The MTF measurement calculation module on-orbit had the function of calculating the edge extension function, line extension function, ESF difference operation, normalization MTF and MTFC parameters. The MTFC image filtering and noise suppression had the function of filtering algorithm and effectively suppressing the noise. The algorithm used System Generator to design the image processing algorithms to simplify the design structure of system and the process redesign. The image gray gradient dot sharpness edge contrast and median-high frequency were enhanced. The image SNR after recovery reduced less than 1 dB compared to the original image. The image restoration system can be widely used in various fields.

The Advanced Gamma-ray Imaging System (AGIS): Telescope Optical System Designs

NASA Astrophysics Data System (ADS)

Hanna, David S.; Buckley, J. H.; Falcone, A.; Fegan, S.; Finley, J.; Guarino, V.; Kaaret, P.; Krawczynski, H.; Krennrich, F.; Konopelko, A.; Romani, R.; Vassilliev, V.; Optical System Working Group; AGIS Collaboration

2008-03-01

The concept of a future ground-based gamma-ray observatory, AGIS, in the energy range 20 GeV-200 TeV is based on an array of 50-200 imaging atmospheric Cherenkov telescopes (IACTs). The anticipated improvement of AGIS sensitivity, angular resolution, and reliability of operation imposes demanding technological and cost requirements on the design of IACTs. In this submission we will focus on the optical system (OS) of AGIS telescopes and consider options which include traditional Davies-Cotton and the other prime-focus telescope designs, as well as the novel two-mirror aplanatic OS originally proposed by Schwarzschild. The emerging new mirror production technologies based on replication processes, such as cold and hot glass slumping, cured CFRP, and electroforming, provide new opportunities for cost effective solutions for the design of the OS. We initially evaluate capabilities of these mirror fabrication methods for the AGIS project.

Survey and documentation of emerging technologies for the Satellite Power System (SPS)

NASA Technical Reports Server (NTRS)

Glaser, P.; Chapman, P.

1981-01-01

The genesis of the solar power satellite (SPS) concept is reviewed historically and the original assumptions and guidelines which led to development of the SPS reference system design concept are discussed. Some guidelines are applicable to almost any SPS design, but others can be changed, leading to new and perhaps preferable systems. In order to stimulate new SPS concepts and to facilitate comparative assessment of emerging SPS technologies, one useful approach is to break the overall system into functional parts. The system functions which must be performed by any SPS concept and the interrelations between them are discussed and a systematic framework is presented for assessing the wide variety of system concepts and subsystem technologies which have been proposed. About 80 alternative SPS technologies are reviewed.

Integrated Avionics System (IAS)

NASA Technical Reports Server (NTRS)

Hunter, D. J.

2001-01-01

As spacecraft designs converge toward miniaturization and with the volumetric and mass constraints placed on avionics, programs will continue to advance the 'state of the art' in spacecraft systems development with new challenges to reduce power, mass, and volume. Although new technologies have improved packaging densities, a total system packaging architecture is required that not only reduces spacecraft volume and mass budgets, but increase integration efficiencies, provide modularity and scalability to accommodate multiple missions. With these challenges in mind, a novel packaging approach incorporates solutions that provide broader environmental applications, more flexible system interconnectivity, scalability, and simplified assembly test and integration schemes. This paper will describe the fundamental elements of the Integrated Avionics System (IAS), Horizontally Mounted Cube (HMC) hardware design, system and environmental test results. Additional information is contained in the original extended abstract.

Centralized PI control for high dimensional multivariable systems based on equivalent transfer function.

PubMed

Luan, Xiaoli; Chen, Qiang; Liu, Fei

2014-09-01

This article presents a new scheme to design full matrix controller for high dimensional multivariable processes based on equivalent transfer function (ETF). Differing from existing ETF method, the proposed ETF is derived directly by exploiting the relationship between the equivalent closed-loop transfer function and the inverse of open-loop transfer function. Based on the obtained ETF, the full matrix controller is designed utilizing the existing PI tuning rules. The new proposed ETF model can more accurately represent the original processes. Furthermore, the full matrix centralized controller design method proposed in this paper is applicable to high dimensional multivariable systems with satisfactory performance. Comparison with other multivariable controllers shows that the designed ETF based controller is superior with respect to design-complexity and obtained performance. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Galactic binary science with the new LISA design

NASA Astrophysics Data System (ADS)

Cornish, Neil; Robson, Travis

2017-05-01

Building on the great success of the LISA Pathfinder mission, the outlines of a new LISA mission design were laid out at the 11th International LISA Symposium in Zurich. The revised design calls for three identical spacecraft forming an equilateral triangle with 2.5 million kilometer sides, and two laser links per side delivering full polarization sensitivity. With the demonstrated Pathfinder performance for the disturbance reduction system, and a well studied design for the laser metrology, it is anticipated that the new mission will have a sensitivity very close to the original LISA design. This implies that the mid-band performance, between 0.5 mHz and 3 mHz, will be limited by unresolved signals from compact binaries in our galaxy. Here we use the new LISA design to compute updated estimates for the galactic confusion noise, the number of resolvable galactic binaries, and the accuracy to which key parameters of these systems can be measured.

Vehicle Systems Engineering and Integration Activities - Phase 5

DTIC Science & Technology

2012-08-31

and Engineering. Its objective is to fundamentally change the capabilities for the design, adaptation, and manufacture of defense systems. Recent...package. The standard RISE package includes an upgraded propulsion system ( turbocharged engine and new transmission), greatly improved driver...original M113A3 and M730A2 vehicles is the turbocharged 275 hp 6V53T engine from Detroit Diesel Corporation. Replacing the earlier 212 hp M113A2

MR guided FUS therapy with a Robotic Assistance System

NASA Astrophysics Data System (ADS)

Jenne, Jürgen W.; Krafft, Axel J.; Maier, Florian; Rauschenberg, Jaane; Semmler, Wolfhard; Huber, Peter E.; Bock, Michael

2009-04-01

Magnetic Resonance imaging guided Focus Ultrasound Surgery (MRgFUS) is a highly precise method to ablate tissue non-invasively. To date, there is only one commercial MRgFUS system available and only a few are in a prototype stage. The objective of this ongoing project is to establish an MRgFUS therapy unit as add-on for a commercially available robotic assistance system originally designed for percutaneous needle interventions in whole-body MR scanners.

Five Indisputable Facts on Modern Power Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bloom, Aaron P; Brinkman, Gregory L; Lopez, Anthony J

This presentation overviews five indisputable facts about modern power systems: Fact one: The grid can handle more renewable generation than previously thought. Fact two: Geographic and resource diversity provide additional reliability to the system. Fact three: Wind and solar forecasting provide significant value. Fact four: Our electric power markets were not originally designed for variable renewables -- but they could be adapted. Fact five: Modern power electronics are creating new sources of essential reliability services.

A Two-Time Scale Decentralized Model Predictive Controller Based on Input and Output Model

PubMed Central

Niu, Jian; Zhao, Jun; Xu, Zuhua; Qian, Jixin

2009-01-01

A decentralized model predictive controller applicable for some systems which exhibit different dynamic characteristics in different channels was presented in this paper. These systems can be regarded as combinations of a fast model and a slow model, the response speeds of which are in two-time scale. Because most practical models used for control are obtained in the form of transfer function matrix by plant tests, a singular perturbation method was firstly used to separate the original transfer function matrix into two models in two-time scale. Then a decentralized model predictive controller was designed based on the two models derived from the original system. And the stability of the control method was proved. Simulations showed that the method was effective. PMID:19834542

An experimental sample of the field gamma-spectrometer based on solid state Si-photomultiplier

NASA Astrophysics Data System (ADS)

Denisov, Viktor; Korotaev, Valery; Titov, Aleksandr; Blokhina, Anastasia; Kleshchenok, Maksim

2017-05-01

Design of optical-electronic devices and systems involves the selection of such technical patterns that under given initial requirements and conditions are optimal according to certain criteria. The original characteristic of the OES for any purpose, defining its most important feature ability is a threshold detection. Based on this property, will be achieved the required functional quality of the device or system. Therefore, the original criteria and optimization methods have to subordinate to the idea of a better detectability. Generally reduces to the problem of optimal selection of the expected (predetermined) signals in the predetermined observation conditions. Thus the main purpose of optimization of the system when calculating its detectability is the choice of circuits and components that provide the most effective selection of a target.

ALC Rooftop Sensor System

DTIC Science & Technology

2017-10-31

Department of the Army position unless so designated by other authorized documents. Citation of manufacturer’s or trade names does not constitute an... Interior view of the new sensor box ...................................................... 3 Fig. 4 Interior of original sensor box...7 Fig. 10 Interior of fiber patch panel .................................................................. 7 Fig. 11

Digital PI-PD controller design for arbitrary order systems: Dominant pole placement approach.

PubMed

Dincel, Emre; Söylemez, Mehmet Turan

2018-05-02

In this paper, a digital PI-PD controller design method is proposed for arbitrary order systems with or without time-delay to achieve desired transient response in the closed-loop via dominant pole placement approach. The digital PI-PD controller design problem is solved by converting the original problem to the digital PID controller design problem. Firstly, parametrization of the digital PID controllers which assign dominant poles to desired location is done. After that the subset of digital PID controller parameters in which the remaining poles are located away from the dominant pole pair is found via Chebyshev polynomials. The obtained PID controller parameters are then transformed into the PI-PD controller parameters by considering the closed-loop controller zero and the design is completed. Success of the proposed design method is firstly demonstrated on an example transfer function and compared with the well-known PID controller methods from the literature through simulations. After that the design method is implemented on the fan and plate laboratory system in a real environment. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Lithium Circuit Test Section Design and Fabrication

NASA Technical Reports Server (NTRS)

Godfroy, Thomas; Garber, Anne

2006-01-01

The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper will discuss the overall system design and build and the component testing findings.

Lithium Circuit Test Section Design and Fabrication

NASA Astrophysics Data System (ADS)

Godfroy, Thomas; Garber, Anne; Martin, James

2006-01-01

The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper discusses the overall system design and build and the component testing findings.

New York City Police Department Automated Fuel Monitoring system. Volume I. Overview. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrath, W.J.; McNamara, M.M.

1981-10-01

The New York City Police Department (NYCPD) Automated Fuel Monitoring system is briefly described from the original study, through system design, to implementation. The system provides complete control of fuel usage for an agency with 4,000 motor vehicles and 25,000 vehicle operators. As far as is known, it is the largest system of its kind installed to date. The system can be scaled up or down to meet the needs of other governmental units. Estimated annual cost savings to NYCPD are $2,000,000.

New York City Police Department Automated Fuel Monitoring system. Volume II. Documentation report. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrath, W.J.; McNamara, M.M.

1981-11-16

The New York City Police Department (NYCPD) Automated Fuel Monitoring system is briefly described from the original study, through system design, to implementation. The system provides complete control of fuel usage for an agency with 4,000 motor vehicles and 25,000 vehicle operators. As far as is known, it is the largest system of its kind installed to date. The system can be scaled up or down to meet the needs of other governmental units. Estimated annual cost savings to NYCPD are $2,000,000.

Spread spectrum communications. Volume 1, 2 & 3

NASA Technical Reports Server (NTRS)

Simon, M. K.; Levitt, B. K.; Omura, J. K.; Scholtz, R. A.

1985-01-01

The design and operation of spread-spectrum (SS) communication systems are examined in an introductory text intended for graduate engineering students and practicing engineers. Chapters are devoted to an overview of SS systems, the historical origins of SS, basic concepts and system models, antijam communication systems, pseudonoise generators, coherent direct-sequence systems, noncoherent frequency-hopped systems, coherent and differentially coherent modulation techniques, pseudonoise acquisition and tracking in direct-sequence receivers, time and frequency synchronization of frequency-hopped receivers, low-probability-of-intercept communication, and multiple-access communication. Graphs, diagrams, and photographs are provided.

[Research and realization of signal processing algorithms based on FPGA in digital ophthalmic ultrasonography imaging].

PubMed

Fang, Simin; Zhou, Sheng; Wang, Xiaochun; Ye, Qingsheng; Tian, Ling; Ji, Jianjun; Wang, Yanqun

2015-01-01

To design and improve signal processing algorithms of ophthalmic ultrasonography based on FPGA. Achieved three signal processing modules: full parallel distributed dynamic filter, digital quadrature demodulation, logarithmic compression, using Verilog HDL hardware language in Quartus II. Compared to the original system, the hardware cost is reduced, the whole image shows clearer and more information of the deep eyeball contained in the image, the depth of detection increases from 5 cm to 6 cm. The new algorithms meet the design requirements and achieve the system's optimization that they can effectively improve the image quality of existing equipment.

Methodology for object-oriented real-time systems analysis and design: Software engineering

NASA Technical Reports Server (NTRS)

Schoeffler, James D.

1991-01-01

Successful application of software engineering methodologies requires an integrated analysis and design life-cycle in which the various phases flow smoothly 'seamlessly' from analysis through design to implementation. Furthermore, different analysis methodologies often lead to different structuring of the system so that the transition from analysis to design may be awkward depending on the design methodology to be used. This is especially important when object-oriented programming is to be used for implementation when the original specification and perhaps high-level design is non-object oriented. Two approaches to real-time systems analysis which can lead to an object-oriented design are contrasted: (1) modeling the system using structured analysis with real-time extensions which emphasizes data and control flows followed by the abstraction of objects where the operations or methods of the objects correspond to processes in the data flow diagrams and then design in terms of these objects; and (2) modeling the system from the beginning as a set of naturally occurring concurrent entities (objects) each having its own time-behavior defined by a set of states and state-transition rules and seamlessly transforming the analysis models into high-level design models. A new concept of a 'real-time systems-analysis object' is introduced and becomes the basic building block of a series of seamlessly-connected models which progress from the object-oriented real-time systems analysis and design system analysis logical models through the physical architectural models and the high-level design stages. The methodology is appropriate to the overall specification including hardware and software modules. In software modules, the systems analysis objects are transformed into software objects.

An airborne remote sensing platform of the Helsinki University of Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nikulainen, M.; Hallikainen, M.; Kemppinen, M.

1996-10-01

In 1994 Helsinki University of Technology acquired a Short SC7 Skyvan turboprop aircraft to be modified to carry remote sensing instruments. As the aircraft is originally designed to carry heavy and space consuming cargo, a modification program was implemented to make the aircraft feasible for remote sensing operations. The twelve-month long modification program had three design objectives: flexibility, accessibility and cost efficiency. The aircraft interior and electrical system were modified. Furthermore, the aircraft is equipped with DGPS-navigation system, multi-channel radiometer system and side looking airborne radar. Future projects include installation of local area network, attitude GPS system, imaging spectrometer andmore » 1.4 GHz radiometer. 6 refs., 5 figs., 1 tab.« less

Modeling Languages Refine Vehicle Design

NASA Technical Reports Server (NTRS)

2009-01-01

Cincinnati, Ohio s TechnoSoft Inc. is a leading provider of object-oriented modeling and simulation technology used for commercial and defense applications. With funding from Small Business Innovation Research (SBIR) contracts issued by Langley Research Center, the company continued development on its adaptive modeling language, or AML, originally created for the U.S. Air Force. TechnoSoft then created what is now known as its Integrated Design and Engineering Analysis Environment, or IDEA, which can be used to design a variety of vehicles and machinery. IDEA's customers include clients in green industries, such as designers for power plant exhaust filtration systems and wind turbines.

The robust model predictive control based on mixed H2/H∞ approach with separated performance formulations and its ISpS analysis

NASA Astrophysics Data System (ADS)

Li, Dewei; Li, Jiwei; Xi, Yugeng; Gao, Furong

2017-12-01

In practical applications, systems are always influenced by parameter uncertainties and external disturbance. Both the H2 performance and the H∞ performance are important for the real applications. For a constrained system, the previous designs of mixed H2/H∞ robust model predictive control (RMPC) optimise one performance with the other performance requirement as a constraint. But the two performances cannot be optimised at the same time. In this paper, an improved design of mixed H2/H∞ RMPC for polytopic uncertain systems with external disturbances is proposed to optimise them simultaneously. In the proposed design, the original uncertain system is decomposed into two subsystems by the additive character of linear systems. Two different Lyapunov functions are used to separately formulate the two performance indices for the two subsystems. Then, the proposed RMPC is designed to optimise both the two performances by the weighting method with the satisfaction of the H∞ performance requirement. Meanwhile, to make the design more practical, a simplified design is also developed. The recursive feasible conditions of the proposed RMPC are discussed and the closed-loop input state practical stable is proven. The numerical examples reflect the enlarged feasible region and the improved performance of the proposed design.

Reliable Location-Based Services from Radio Navigation Systems

PubMed Central

Qiu, Di; Boneh, Dan; Lo, Sherman; Enge, Per

2010-01-01

Loran is a radio-based navigation system originally designed for naval applications. We show that Loran-C’s high-power and high repeatable accuracy are fantastic for security applications. First, we show how to derive a precise location tag—with a sensitivity of about 20 meters—that is difficult to project to an exact location. A device can use our location tag to block or allow certain actions, without knowing its precise location. To ensure that our tag is reproducible we make use of fuzzy extractors, a mechanism originally designed for biometric authentication. We build a fuzzy extractor specifically designed for radio-type errors and give experimental evidence to show its effectiveness. Second, we show that our location tag is difficult to predict from a distance. For example, an observer cannot predict the location tag inside a guarded data center from a few hundreds of meters away. As an application, consider a location-aware disk drive that will only work inside the data center. An attacker who steals the device and is capable of spoofing Loran-C signals, still cannot make the device work since he does not know what location tag to spoof. We provide experimental data supporting our unpredictability claim. PMID:22163532

Control console replacement at the WPI Reactor. [Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-12-31

With partial funding from the Department of Energy (DOE) University Reactor Instrumentation Upgrade Program (DOE Grant No. DE-FG02-90ER12982), the original control console at the Worcester Polytechnic Institute (WPI) Reactor has been replaced with a modern system. The new console maintains the original design bases and functionality while utilizing current technology. An advanced remote monitoring system has been added to augment the educational capabilities of the reactor. Designed and built by General Electric in 1959, the open pool nuclear training reactor at WPI was one of the first such facilities in the nation located on a university campus. Devoted to undergraduatemore » use, the reactor and its related facilities have been since used to train two generations of nuclear engineers and scientists for the nuclear industry. The reactor power level was upgraded from 1 to 10 kill in 1969, and its operating license was renewed for 20 years in 1983. In 1988, the reactor was converted to low enriched uranium. The low power output of the reactor and ergonomic facility design make it an ideal tool for undergraduate nuclear engineering education and other training.« less

Development Status of Amine-based, Combined Humidity, CO2, and Trace Contaminant Control System for CEV

NASA Technical Reports Server (NTRS)

Smith, Fred; Perry, Jay; Nalette, Tim; Papale, William

2006-01-01

Under a NASA-sponsored technology development project, a multi-disciplinary team consisting of industry, academia, and government organizations lead by Hamilton Sundstrand is developing an amine-based humidity and CO2 removal process and prototype equipment for Vision for Space Exploration (VSE) applications. Originally this project sought to research enhanced amine formulations and incorporate a trace contaminant control capability into the sorbent. In October 2005, NASA re-directed the project team to accelerate the delivery of hardware by approximately one year and emphasize deployment on board the Crew Exploration Vehicle (CEV) as the near-term developmental goal. Preliminary performance requirements were defined based on nominal and off-nominal conditions and the design effort was initiated using the baseline amine sorbent, SA9T. As part of the original project effort, basic sorbent development was continued with the University of Connecticut and dynamic equilibrium trace contaminant adsorption characteristics were evaluated by NASA. This paper summarizes the University sorbent research effort, the basic trace contaminant loading characteristics of the SA9T sorbent, design support testing, and the status of the full-scale system hardware design and manufacturing effort.

Reliable location-based services from radio navigation systems.

PubMed

Qiu, Di; Boneh, Dan; Lo, Sherman; Enge, Per

2010-01-01

Loran is a radio-based navigation system originally designed for naval applications. We show that Loran-C's high-power and high repeatable accuracy are fantastic for security applications. First, we show how to derive a precise location tag--with a sensitivity of about 20 meters--that is difficult to project to an exact location. A device can use our location tag to block or allow certain actions, without knowing its precise location. To ensure that our tag is reproducible we make use of fuzzy extractors, a mechanism originally designed for biometric authentication. We build a fuzzy extractor specifically designed for radio-type errors and give experimental evidence to show its effectiveness. Second, we show that our location tag is difficult to predict from a distance. For example, an observer cannot predict the location tag inside a guarded data center from a few hundreds of meters away. As an application, consider a location-aware disk drive that will only work inside the data center. An attacker who steals the device and is capable of spoofing Loran-C signals, still cannot make the device work since he does not know what location tag to spoof. We provide experimental data supporting our unpredictability claim.

Highly Survivable Avionics Systems for Long-Term Deep Space Exploration

NASA Technical Reports Server (NTRS)

Alkalai, L.; Chau, S.; Tai, A. T.

2001-01-01

The design of highly survivable avionics systems for long-term (> 10 years) exploration of space is an essential technology for all current and future missions in the Outer Planets roadmap. Long-term exposure to extreme environmental conditions such as high radiation and low-temperatures make survivability in space a major challenge. Moreover, current and future missions are increasingly using commercial technology such as deep sub-micron (0.25 microns) fabrication processes with specialized circuit designs, commercial interfaces, processors, memory, and other commercial off the shelf components that were not designed for long-term survivability in space. Therefore, the design of highly reliable, and available systems for the exploration of Europa, Pluto and other destinations in deep-space require a comprehensive and fresh approach to this problem. This paper summarizes work in progress in three different areas: a framework for the design of highly reliable and highly available space avionics systems, distributed reliable computing architecture, and Guarded Software Upgrading (GSU) techniques for software upgrading during long-term missions. Additional information is contained in the original extended abstract.

The Space Infrared Interferometric Telescope (SPIRIT): Optical System Design Considerations

NASA Technical Reports Server (NTRS)

Wilson, Mark E.; Leisawitz, David; Martino, Anthony J.; Budinoff, Jason; Quijada, Manuel; Hyde, Tupper

2007-01-01

SPIRIT is a candidate NASA Origins Probe mission. It is a spatial and spectral interferometer operating at 4 K with an operating wavelength range 25 - 400 microns. This paper describes the various components of the candidate optical system, including telescopes, pointing and tracking optics, along with their functions. Some of the tradeoffs involved in selecting various components, with their particular characteristics, are described.

Technical Assessment: Autonomy

DTIC Science & Technology

2015-02-23

low-cost sensors for automotive applications, mobile devices, and video games . If DoD develops CONOPS for lower- performance systems, there is an...advancement in this area is Microsoft’s Kinect technology. While originally designed for the Xbox video game platform, it is now being used or developed for...One area worthy of consideration is applied game theory, which may allow systems to effectively respond to adversary actions. Recommendation 4

Safety Aspects of Big Cryogenic Systems Design

NASA Astrophysics Data System (ADS)

Chorowski, M.; Fydrych, J.; Poliński, J.

2010-04-01

Superconductivity and helium cryogenics are key technologies in the construction of large scientific instruments, like accelerators, fusion reactors or free electron lasers. Such cryogenic systems may contain more than hundred tons of helium, mostly in cold and high-density phases. In spite of the high reliability of the systems, accidental loss of the insulation vacuum, pipe rupture or rapid energy dissipation in the cold helium can not be overlooked. To avoid the danger of over-design pressure rise in the cryostats, they need to be equipped with a helium relief system. Such a system is comprised of safety valves, bursting disks and optionally cold or warm quench lines, collectors and storage tanks. Proper design of the helium safety relief system requires a good understanding of worst case scenarios. Such scenarios will be discussed, taking into account different possible failures of the cryogenic system. In any case it is necessary to estimate heat transfer through degraded vacuum superinsulation and mass flow through the valves and safety disks. Even if the design of the helium relief system does not foresee direct helium venting into the environment, an occasional emergency helium spill may happen. Helium propagation in the atmosphere and the origins of oxygen-deficiency hazards will be discussed.

Anatomical information in radiation treatment planning.

PubMed

Kalet, I J; Wu, J; Lease, M; Austin-Seymour, M M; Brinkley, J F; Rosse, C

1999-01-01

We report on experience and insights gained from prototyping, for clinical radiation oncologists, a new access tool for the University of Washington Digital Anatomist information resources. This access tool is designed to integrate with a radiation therapy planning (RTP) system in use in a clinical setting. We hypothesize that the needs of practitioners in a clinical setting are different from the needs of students, the original targeted users of the Digital Anatomist system, but that a common knowledge resource can serve both. Our prototype was designed to help define those differences and study the feasibility of a full anatomic reference system that will support both clinical radiation therapy and all the existing educational applications.

Generating multi-double-scroll attractors via nonautonomous approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Qinghui; Xie, Qingguo, E-mail: qgxie@mail.hust.edu.cn; Shen, Yi

It is a common phenomenon that multi-scroll attractors are realized by introducing the various nonlinear functions with multiple breakpoints in double scroll chaotic systems. Differently, we present a nonautonomous approach for generating multi-double-scroll attractors (MDSA) without changing the original nonlinear functions. By using the multi-level-logic pulse excitation technique in double scroll chaotic systems, MDSA can be generated. A Chua's circuit, a Jerk circuit, and a modified Lorenz system are given as designed example and the Matlab simulation results are presented. Furthermore, the corresponding realization circuits are designed. The Pspice results are in agreement with numerical simulation results, which verify themore » availability and feasibility of this method.« less

Particle-Based Simulations of Microscopic Thermal Properties of Confined Systems

DTIC Science & Technology

2014-11-01

velocity versus electric field in gallium arsenide (GaAs) computed with the original CMC table structure (squares) at temperature T=150K, and the new...computer-aided design Cellular Monte Carlo Ensemble Monte Carlo gallium arsenide Heat Transport Equation DARPA Defense Advanced Research Projects

40 CFR 205.169 - Labeling requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... standard) dBA for the following motorcycles: (list of model specific codes). Installation of this exhaust... designed and marketed for motorcycles, and tested in accordance with § 205.168 as a constituent of a complete exhaust system comprising non-original equipment components (other than itself), as provided for...

40 CFR 205.169 - Labeling requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... standard) dBA for the following motorcycles: (list of model specific codes). Installation of this exhaust... designed and marketed for motorcycles, and tested in accordance with § 205.168 as a constituent of a complete exhaust system comprising non-original equipment components (other than itself), as provided for...

Implementation Issues for Cr6+ Free M&P

DTIC Science & Technology

2008-02-27

85582 Performance Range, with Topcoat MIL-PRF-23377 & MIL-PRF-85582 Performance Range, no Topcoat NCAP Data Assessment • Project originally designed to...documented and distributed as part of ESTCP NCAP project report • Initial assessment suggests that a standard practice to assess coating systems can be

Evaluating Digital Authoring Tools

ERIC Educational Resources Information Center

Wilde, Russ

2004-01-01

As the quality of authoring software increases, online course developers become less reliant on proprietary learning management systems, and develop skills in the design of original, in-house materials and the delivery platforms for them. This report examines the capabilities of digital authoring software tools for the development of learning…

Pricing strategy in a dual-channel and remanufacturing supply chain system

NASA Astrophysics Data System (ADS)

Jiang, Chengzhi; Xu, Feng; Sheng, Zhaohan

2010-07-01

This article addresses the pricing strategy problems in a supply chain system where the manufacturer sells original products and remanufactured products via indirect retailer channels and direct Internet channels. Due to the complexity of that system, agent technologies that provide a new way for analysing complex systems are used for modelling. Meanwhile, in order to reduce the computational load of searching procedure for optimal prices and profits, a learning search algorithm is designed and implemented within the multi-agent supply chain model. The simulation results show that the proposed model can find out optimal prices of original products and remanufactured products in both channels, which lead to optimal profits of the manufacturer and the retailer. It is also found that the optimal profits are increased by introducing direct channel and remanufacturing. Furthermore, the effect of customer preference, direct channel cost and remanufactured unit cost on optimal prices and profits are examined.

Flight testing the Digital Electronic Engine Control (DEEC) A unique management experience

NASA Technical Reports Server (NTRS)

Putnam, T. W.; Burcham, F. W., Jr.; Kock, B. M.

1983-01-01

The concept for the DEEC had its origin in the early 1970s. At that time it was recognized that the F100 engine performance, operability, reliability, and cost could be substantially improved by replacing the original mechanical/supervisory electronic control system with a full-authority digital control system. By 1978, the engine manufacturer had designed and initiated the procurement of flight-qualified control system hardware. As a precursor to an integrated controls program, a flight evaluation of the DEEC system on the F-15 aircraft was proposed. Questions regarding the management of the DEEC flight evaluation program are discussed along with the program elements, the technical results of the F-15 evaluation, and the impact of the flight evaluation on after-burning turbofan controls technology and its use in and application to military aircraft. The lessons learned through the conduct of the program are discussed.

Magnetic suspension and balance system advanced study

NASA Technical Reports Server (NTRS)

Boom, R. W.; Eyssa, Y. M.; Mcintosh, G. E.; Abdelsalam, M. K.

1985-01-01

An improved compact design for a superconducting magnetic suspension and balance system for an 8 ft. x 8 ft. transonic wind tunnel is developed. The original design of an MSBS in NASA Cr-3802 utilized 14 external superconductive coils and a superconductive solenoid in the airplane test model suspended in a wind tunnel. The improvements are in the following areas: test model solenoid options, dynamic force limits on the model, magnet cooling options, structure and cryogenic designs, power supply specifications, and cost and performance evaluations. The improvements are: MSBS cost reduction of 28%, weight; reduction of 43%, magnet system ampere-meter reduction of 38%, helium liquifier capacity reduction by 33%, magnet system stored energy reduction by 55%, AC loss to liquid helium reduced by 76%, system power supply reduced by 68%, test coil pole strength increased by 19%, wing magnetization increased by 40%, and control frequency limit increased by 200% from 10 Hz to 30 Hz. The improvements are due to: magnetic holmium coil forms in the test model, better rare earth permanent magnets in the wings, fiberglass-epoxy structure replacing stainless steel, better coil configuration, and new saddle roll coil design.

Algal Supply System Design - Harmonized Version

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abodeely, Jared; Stevens, Daniel; Ray, Allison

2013-03-01

The objective of this design report is to provide an assessment of current technologies used for production, dewatering, and converting microalgae cultivated in open-pond systems to biofuel. The original draft design was created in 2011 and has subsequently been brought into agreement with the DOE harmonized model. The design report extends beyond this harmonized model to discuss some of the challenges with assessing algal production systems, including the ability to (1) quickly assess alternative algal production system designs, (2) assess spatial and temporal variability, and (3) perform large-scale assessments considering multiple scenarios for thousands of potential sites. The Algae Logisticsmore » Model (ALM) was developed to address each of these limitations of current modeling efforts to enable assessment of the economic feasibility of algal production systems across the United States. The (ALM) enables (1) dynamic assessments using spatiotemporal conditions, (2) exploration of algal production system design configurations, (3) investigation of algal production system operating assumptions, and (4) trade-off assessments with technology decisions and operating assumptions. The report discusses results from the ALM, which is used to assess the baseline design determined by harmonization efforts between U.S. DOE national laboratories. Productivity and resource assessment data is provided by coupling the ALM with the Biomass Assessment Tool developed at PNNL. This high-fidelity data is dynamically passed to the ALM and used to help better understand the impacts of spatial and temporal constraints on algal production systems by providing a cost for producing extracted algal lipids annually for each potential site.« less

The constructal law and the evolution of design in nature.

PubMed

Bejan, Adrian; Lorente, Sylvie

2011-10-01

The constructal law accounts for the universal phenomenon of generation and evolution of design (configuration, shape, structure, pattern, rhythm). This phenomenon is observed across the board, in animate, inanimate and human systems. The constructal law states the time direction of the evolutionary design phenomenon. It defines the concept of design evolution in physics. Along with the first and second law, the constructal law elevates thermodynamics to a science of systems with configuration. In this article we review the more recent work of our group, with emphasis on the advances made with the constructal law in the natural sciences. Highlighted are the oneness of animate and inanimate designs, the origin of finite-size organs on animals and vehicles, the flow of stresses as the generator of design in solid structures (skeletons, vegetation), the universality and rigidity of hierarchy in all flow systems, and the global design of human flows. Noteworthy is the tapestry of distributed energy systems, which balances nodes of production with networks of distribution on the landscape, and serves as key to energy sustainability and empowerment. At the global level, the constructal law accounts for the geography and design of human movement, wealth and communications. Copyright © 2011 Elsevier B.V. All rights reserved.

Redesigning printed educational materials for primary care physicians: design improvements increase usability.

PubMed

Grudniewicz, Agnes; Bhattacharyya, Onil; McKibbon, K Ann; Straus, Sharon E

2015-11-04

Printed educational materials (PEMs) are a frequently used tool to disseminate clinical information and attempt to change behavior within primary care. However, their effect on clinician behavior is limited. In this study, we explored how PEMs can be redesigned to better meet the needs of primary care physicians (PCPs) and whether usability and selection can be increased when design principles and user preferences are used. We redesigned a publicly available PEM using physician preferences, design principles, and graphic designer support. We invited PCPs to select their preferred document between the redesigned and original versions in a discrete choice experiment, followed by an assessment of usability with the System Usability Scale and a think aloud process. We conducted this study in both a controlled and opportunistic setting to determine whether usability testing results vary by study location. Think aloud data was thematically analyzed, and results were interpreted using the Technology Acceptance Model. One hundred and eighty four PCPs participated in the discrete choice experiment at the 2014 Family Medicine Forum, a large Canadian conference for family physicians. Of these, 87.7 % preferred the redesigned version. Follow-up interviews were held with a randomly selected group of seven participants. We repeated this in a controlled setting in Toronto, Canada, with a set of 14 participants. Using the System Usability Scale, we found that usability scores were significantly increased with the redesign (p < 0.001). We also found that when PCPs were given the choice between the two versions, they selected the redesigned version as their preferred PEM more often than the original (p < 0.001). Results did not appear to differ between the opportunistic and controlled setting. We used the results of the think aloud process to add to a list of end user preferences developed in a previous study. We found that redesigning a PEM with user preferences and design principles can improve its usability and result in the PEM being selected more often than the original. We feel this finding supports the involvement of the user, application of design principles, and the assistance of a graphic designer in the development of PEMs.

Food Service System

NASA Technical Reports Server (NTRS)

1992-01-01

The 3M Food Service System 2 employs a "cook/chill" concept for serving food in hospitals. The system allows staff to prepare food well in advance, maintain heat, visual appeal and nutritional value as well as reducing operating costs. The integral heating method, which keeps hot foods hot and cold foods cold, was developed by 3M for the Apollo Program. In the 1970s, the company commercialized the original system and in 1991, introduced Food Service System 2. Dishes are designed to resemble those used at home, and patient satisfaction has been high.

The SMARTSat redesign study

NASA Technical Reports Server (NTRS)

Lu, Richard; Chan, Jeffrey

1994-01-01

The original design of the Student Mentored Advanced Research and Technology Satellite (SMARTSat) began in January of 1994. The mission adhered to the guidelines and constraints set forth by the Student Explorer Demonstration Initiative Proposal, which was sponsored by the Universities Space Research Association. This report represents a redesign of that original concept. The main differences include a higher orbit and a three axis stabilization system. Of course, these changes imparted significant effects upon the other subsystems. Outlined in this document are those modifications and it offers some new analyses as well. For each subsystem there is a brief description, followed by relevant design assumptions, a summary of conclusions, and finally all pertinent supporting data and graphs. Towards the end of the report. the important issue of cost is addressed as well. Whenever possible, parametric analyses were made.

Microwave vision for robots

NASA Technical Reports Server (NTRS)

Lewandowski, Leon; Struckman, Keith

1994-01-01

Microwave Vision (MV), a concept originally developed in 1985, could play a significant role in the solution to robotic vision problems. Originally our Microwave Vision concept was based on a pattern matching approach employing computer based stored replica correlation processing. Artificial Neural Network (ANN) processor technology offers an attractive alternative to the correlation processing approach, namely the ability to learn and to adapt to changing environments. This paper describes the Microwave Vision concept, some initial ANN-MV experiments, and the design of an ANN-MV system that has led to a second patent disclosure in the robotic vision field.

Nature and origins of virtual environments - A bibliographical essay

NASA Technical Reports Server (NTRS)

Ellis, S. R.

1991-01-01

Virtual environments presented via head-mounted, computer-driven displays provide a new media for communication. They may be analyzed by considering: (1) what may be meant by an environment; (2) what is meant by the process of virtualization; and (3) some aspects of human performance that constrain environmental design. Their origins are traced from previous work in vehicle simulation and multimedia research. Pointers are provided to key technical references, in the dispersed, archival literature, that are relevant to the development and evaluation of virtual-environment interface systems.

Cargo Movement Operations System (CMOS). Final Software Design Document

DTIC Science & Technology

1990-09-27

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED [ ] ORIGINATOR CONTROL NUMBER: SDDI-0002 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: A006-03 DATE: 09/27/90 ORIGINATOR NAME: Patrick L. Combs OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 272-2999 SUBSTANTIVE: X EDITORIAL: PAGE NUMBER: iv PARA NUMBER: 4.18.2 COMMENT OR RECOMMENDED CHANGE: Delete Ř.18.2". RATIONALE: The paragraph number is incorrect and was called forward to be placed in the Table of Contents. The number should read Ř.18.1.2" and

Cargo Movement Operations System (CMOS). Final Software Design Document Increment III, (PC UNIX - Navy Configuration)

DTIC Science & Technology

1991-07-03

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED ( ] ORIGINATOR CONTROL NUMBER: SDD-0003 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: A006-02 DATE: 07/03/91 ORIGINATOR NAME: Vivian L. Martin OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 272-2999 SUBSTANTIVE: X EDITORIAL: PAGE NUMBER: L-1 PARA NUMBER: 10 COMMENT OR RECOMMENDED CHANGE: Explain the effect of "no longer required" or "replaced" CSUs on the Navy configuration Menu hierarchy. RATIONALE: Paragraph 10 states that the CMOS menu heirarchy is

31. Photocopy of line illustration; originally published in William N. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. Photocopy of line illustration; originally published in William N. Carey, 'St. Paul Builds an Airport One Mile From Post Office,' Engineering News-Record, (August 21, 1930), figure 6, page 294; SHOWS CANTILEVERED ROOF-TRUSS SYSTEM OF MUNICIPAL HANGAR COMPLETED AT ST. PAUL MUNICIPAL AIRPORT IN 1930; THE STRUCTURAL DESIGN WAS BASED ON THAT OF THE NORTHWEST AIRWAYS HANGAR, EXCEPT FOR THE SUBSTITUTION OF BOWSTRING TRUSSES FOR TRAPEZOIDAL TRUSSES - Northwest Airways Hangar & Administration Building, 590 Bayfield Street, St. Paul Downtown Airport (Holman), Saint Paul, Ramsey County, MN

C-Based Design Methodology and Topological Change for an Indian Agricultural Tractor Component

NASA Astrophysics Data System (ADS)

Matta, Anil Kumar; Raju, D. Ranga; Suman, K. N. S.; Kranthi, A. S.

2018-06-01

The failure of tractor components and their replacement has now become very common in India because of re-cycling, re-sale, and duplication. To over come the problem of failure we propose a design methodology for topological change co-simulating with software's. In the proposed Design methodology, the designer checks Paxial, Pcr, Pfailue, τ by hand calculations, from which refined topological changes of R.S.Arm are formed. We explained several techniques employed in the component for reduction, removal of rib material to change center of gravity and centroid point by using system C for mixed level simulation and faster topological changes. The design process in system C can be compiled and executed with software, TURBO C7. The modified component is developed in proE and analyzed in ANSYS. The topologically changed component with slot 120 × 4.75 × 32.5 mm at the center showed greater effectiveness than the original component.

Design optimization of a high specific speed Francis turbine runner

NASA Astrophysics Data System (ADS)

Enomoto, Y.; Kurosawa, S.; Kawajiri, H.

2012-11-01

Francis turbine is used in many hydroelectric power stations. This paper presents the development of hydraulic performance in a high specific speed Francis turbine runner. In order to achieve the improvements of turbine efficiency throughout a wide operating range, a new runner design method which combines the latest Computational Fluid Dynamics (CFD) and a multi objective optimization method with an existing design system was applied in this study. The validity of the new design system was evaluated by model performance tests. As the results, it was confirmed that the optimized runner presented higher efficiency compared with an originally designed runner. Besides optimization of runner, instability vibration which occurred at high part load operating condition was investigated by model test and gas-liquid two-phase flow analysis. As the results, it was confirmed that the instability vibration was caused by oval cross section whirl which was caused by recirculation flow near runner cone wall.

A novel double loop control model design for chemical unstable processes.

PubMed

Cong, Er-Ding; Hu, Ming-Hui; Tu, Shan-Tung; Xuan, Fu-Zhen; Shao, Hui-He

2014-03-01

In this manuscript, based on Smith predictor control scheme for unstable process in industry, an improved double loop control model is proposed for chemical unstable processes. Inner loop is to stabilize integrating the unstable process and transform the original process to first-order plus pure dead-time dynamic stable process. Outer loop is to enhance the performance of set point response. Disturbance controller is designed to enhance the performance of disturbance response. The improved control system is simple with exact physical meaning. The characteristic equation is easy to realize stabilization. Three controllers are separately design in the improved scheme. It is easy to design each controller and good control performance for the respective closed-loop transfer function separately. The robust stability of the proposed control scheme is analyzed. Finally, case studies illustrate that the improved method can give better system performance than existing design methods. © 2013 ISA Published by ISA All rights reserved.

C-Based Design Methodology and Topological Change for an Indian Agricultural Tractor Component

NASA Astrophysics Data System (ADS)

Matta, Anil Kumar; Raju, D. Ranga; Suman, K. N. S.; Kranthi, A. S.

2018-02-01

The failure of tractor components and their replacement has now become very common in India because of re-cycling, re-sale, and duplication. To over come the problem of failure we propose a design methodology for topological change co-simulating with software's. In the proposed Design methodology, the designer checks Paxial, Pcr, Pfailue, τ by hand calculations, from which refined topological changes of R.S.Arm are formed. We explained several techniques employed in the component for reduction, removal of rib material to change center of gravity and centroid point by using system C for mixed level simulation and faster topological changes. The design process in system C can be compiled and executed with software, TURBO C7. The modified component is developed in proE and analyzed in ANSYS. The topologically changed component with slot 120 × 4.75 × 32.5 mm at the center showed greater effectiveness than the original component.

Complex multidisciplinary systems decomposition for aerospace vehicle conceptual design and technology acquisition

NASA Astrophysics Data System (ADS)

Omoragbon, Amen

Although, the Aerospace and Defense (A&D) industry is a significant contributor to the United States' economy, national prestige and national security, it experiences significant cost and schedule overruns. This problem is related to the differences between technology acquisition assessments and aerospace vehicle conceptual design. Acquisition assessments evaluate broad sets of alternatives with mostly qualitative techniques, while conceptual design tools evaluate narrow set of alternatives with multidisciplinary tools. In order for these two fields to communicate effectively, a common platform for both concerns is desired. This research is an original contribution to a three-part solution to this problem. It discusses the decomposition step of an innovation technology and sizing tool generation framework. It identifies complex multidisciplinary system definitions as a bridge between acquisition and conceptual design. It establishes complex multidisciplinary building blocks that can be used to build synthesis systems as well as technology portfolios. It also describes a Graphical User Interface Designed to aid in decomposition process. Finally, it demonstrates an application of the methodology to a relevant acquisition and conceptual design problem posed by the US Air Force.

The Earth Observing System (EOS) Ground System: Leveraging an Existing Operational Ground System Infrastructure to Support New Missions

NASA Technical Reports Server (NTRS)

Hardison, David; Medina, Johnny; Dell, Greg

2016-01-01

The Earth Observer System (EOS) was officially established in 1990 and went operational in December 1999 with the launch of its flagship spacecraft Terra. Aqua followed in 2002 and Aura in 2004. All three spacecraft are still operational and producing valuable scientific data. While all are beyond their original design lifetime, they are expected to remain viable well into the 2020s. The EOS Ground System is a multi-mission system based at NASA Goddard Space Flight Center that supports science and spacecraft operations for these three missions. Over its operational lifetime to date, the EOS Ground System has evolved as needed to accommodate mission requirements. With an eye towards the future, several updates are currently being deployed. Subsystem interconnects are being upgraded to reduce data latency and improve system performance. End-of-life hardware and operating systems are being replaced to mitigate security concerns and eliminate vendor support gaps. Subsystem hardware is being consolidated through the migration to Virtual Machine based platforms. While mission operations autonomy was not a design goal of the original system concept, there is an active effort to apply state-of-the-art products from the Goddard Mission Services Evolution Center (GMSEC) to facilitate automation where possible within the existing heritage architecture. This presentation will provide background information on the EOS ground system architecture and evolution, discuss latest improvements, and conclude with the results of a recent effort that investigated how the current system could accommodate a proposed new earth science mission.

Logical design of a decision support system to forecast technology, prices and costs for the national communications system

NASA Astrophysics Data System (ADS)

Williams, K. A.; Partridge, E. C., III

1984-09-01

Originally envisioned as a means to integrate the many systems found throughout the government, the general mission of the NCS continues to be to ensure the survivability of communications during and subsequent to any national emergency. In order to accomplish this mission the NCS is an arrangement of heterogeneous telecommunications systems which are provided by their sponsor Federal agencies. The physical components of Federal telecommunications systems and networks include telephone and digital data switching facilities and primary common user communications centers; Special purpose local delivery message switching and exchange facilities; Government owned or leased radio systems; Technical control facilities which are under exclusive control of a government agency. This thesis describes the logical design of a proposed decision support system for use by the National Communications System in forecasting technology, prices, and costs. It is general in nature and only includes those forecasting models which are suitable for computer implementation. Because it is a logical design it can be coded and applied in many different hardware and/or software configurations.

Transcription and the IELTS Speaking Test: Facilitating Development

ERIC Educational Resources Information Center

Stones, Thomas P.

2013-01-01

This article describes a transcription task cycle that was designed to facilitate the development of skills for the IELTS (International English Language Testing System) speaking test at a language school in Japan. The cycle involved practice test, transcription, student correction, teacher correction, and retrial of the original test and…

Getting to the Point in Pinpoint Landing

NASA Technical Reports Server (NTRS)

1998-01-01

Assisted by Langley Research Center's Small Business Technology Transfer (STTR) Program, IntegriNautics has developed a commercialized precision landing system. The idea finds its origins in Stanford University work on a satellite test of Einstein's General Theory of Relativity, where Stanford has designed a new high-performance altitude-determining hardware.

Designed for Learning: Inside and Out.

ERIC Educational Resources Information Center

Sutton, Rodney K.

1996-01-01

Built 7 years after the original plan and budget were approved, Brunswick High School (Maine) houses 1,200 students on 50 acres and contains the latest technological features. Among these are energy management systems that students can see firsthand, a traditional library with 21st-century features, and interactive environmental learning from…

Political Education in the Former German Democratic Republic.

ERIC Educational Resources Information Center

Dumas, Wayne; Dumas, Alesia

1996-01-01

Investigates civic education curricular reform in the former German Democratic Republic (GDR). Discusses the problems inherent in reforming an entire educational system, from textbooks to teachers, originally designed for Marxist-Leninist purposes. Examines the German state educational structure and the role that the main political parties play in…

Functional and Noncategorical Identification and Intervention in Special Education.

ERIC Educational Resources Information Center

Reschly, Daniel J., Ed.; Tilly, W. David, III, Ed.; Grimes, Jeffrey P., Ed.

This volume presents 12 papers that address the increasing shift toward functional and noncategorical approaches to special education. The papers are: (1) "Origins of Categorical Special Education Services in Schools and a Rationale for Changing Them" (Jim Ysseldyke and Doug Marston); (2) "Reform Trends and System Design Alternatives" (Dan Reschly…

Montessori Education: An Idea Whose Time Has Come?

ERIC Educational Resources Information Center

Torrence, Martha

2012-01-01

Educational institutions change slowly, and sometimes superficially at best. Large public (and sometimes smaller private) systems can be highly resistant to deep change. Schools are notorious for rearranging the desk chairs for a while, then reverting back to something very close to the original design. Even the most well-intentioned of…

Stripline Antenna Beam-Forming Network

NASA Technical Reports Server (NTRS)

Cramer, P. W.

1984-01-01

Stripline antenna beam-forming network includes 87 beam ports and 136 feed-element ports and contained on only two microstrip boards. Both uplink and downlink strips supported on same boards. Originally used for communications coverage of continental United States for Land Mobile Satellite System, structure of interest to antenna designers in other applications.

Trends in Instructional Technology.

ERIC Educational Resources Information Center

Brown, James W., Ed.

This collection of five articles presents the viewpoints of experts on various aspects of the field of instructional technology (IT). Wesley C. Meierhenry traces the history of IT from its original emphasis on audiovisual media to its current concern with instructional design and the use of systems and systematic approaches. Henry T. Ingle…

Seeking a State Workforce Strategy

ERIC Educational Resources Information Center

Fischer, David Jason; Mack, Melinda

2015-01-01

New York's workforce system is a complicated entity that engages nearly a dozen state agencies and myriad funding streams originating at the federal and state levels, and operates on the ground in ten economic development regions, 33 designated workforce investment areas, community-based organizations, labor unions and 62 counties. This report…

Integrating an Automatic Judge into an Open Source LMS

ERIC Educational Resources Information Center

Georgouli, Katerina; Guerreiro, Pedro

2011-01-01

This paper presents the successful integration of the evaluation engine of Mooshak into the open source learning management system Claroline. Mooshak is an open source online automatic judge that has been used for international and national programming competitions. although it was originally designed for programming competitions, Mooshak has also…

The Computer as a Tutorial Laboratory: The Stanford BIP Project.

ERIC Educational Resources Information Center

Barr, Avron; And Others

The BASIC Instructional Program (BIP) is an interactive problem-solving laboratory that offers tutorial assistance to students solving introductory programing problems in the BASIC language. After a brief review of the rationale and origins of the BIP instructional system, the design and implementation of BIP's curriculum information network are…

APS Storage Ring Monopulse RF BPM Upgrade

NASA Astrophysics Data System (ADS)

Lill, R.; Pietryla, A.; Norum, E.; Lenkszus, F.

2004-11-01

The Advanced Photon Source (APS) is a third-generation synchrotron light source in its ninth year of operation. The storage ring monopulse radio frequency (rf) beam position monitor (BPM) was designed to measure single-turn and multi-turn beam positions for operations and machine physics studies. Many of the components used in the original design are obsolete and costly to replace. In this paper we present a proposal to upgrade the monopulse rf BPMs in which the existing system hardware is repartitioned and the aging data acquisition system is replaced. By replacing only the data acquisition system, we will demonstrate a cost-effective approach to improved beam stability, reliability, and enhanced postmortem capabilities. An eight-channel ADC/digitizer VXI board with sampling rate of up to 105 MHz (per channel) and 14-bit resolution coupled with a field-programmable gate array and embedded central processing will provide the flexibility to revitalize this system for another decade of operation. We will discuss the upgrade system specifications, design, and prototype test results.

Scaling Deep Learning on GPU and Knights Landing clusters

DOE PAGES

You, Yang; Buluc, Aydin; Demmel, James

2017-09-26

The speed of deep neural networks training has become a big bottleneck of deep learning research and development. For example, training GoogleNet by ImageNet dataset on one Nvidia K20 GPU needs 21 days. To speed up the training process, the current deep learning systems heavily rely on the hardware accelerators. However, these accelerators have limited on-chip memory compared with CPUs. To handle large datasets, they need to fetch data from either CPU memory or remote processors. We use both self-hosted Intel Knights Landing (KNL) clusters and multi-GPU clusters as our target platforms. From an algorithm aspect, current distributed machine learningmore » systems are mainly designed for cloud systems. These methods are asynchronous because of the slow network and high fault-tolerance requirement on cloud systems. We focus on Elastic Averaging SGD (EASGD) to design algorithms for HPC clusters. Original EASGD used round-robin method for communication and updating. The communication is ordered by the machine rank ID, which is inefficient on HPC clusters. First, we redesign four efficient algorithms for HPC systems to improve EASGD's poor scaling on clusters. Async EASGD, Async MEASGD, and Hogwild EASGD are faster \\textcolor{black}{than} their existing counterparts (Async SGD, Async MSGD, and Hogwild SGD, resp.) in all the comparisons. Finally, we design Sync EASGD, which ties for the best performance among all the methods while being deterministic. In addition to the algorithmic improvements, we use some system-algorithm codesign techniques to scale up the algorithms. By reducing the percentage of communication from 87% to 14%, our Sync EASGD achieves 5.3x speedup over original EASGD on the same platform. We get 91.5% weak scaling efficiency on 4253 KNL cores, which is higher than the state-of-the-art implementation.« less

Scaling Deep Learning on GPU and Knights Landing clusters

DOE Office of Scientific and Technical Information (OSTI.GOV)

You, Yang; Buluc, Aydin; Demmel, James

The speed of deep neural networks training has become a big bottleneck of deep learning research and development. For example, training GoogleNet by ImageNet dataset on one Nvidia K20 GPU needs 21 days. To speed up the training process, the current deep learning systems heavily rely on the hardware accelerators. However, these accelerators have limited on-chip memory compared with CPUs. To handle large datasets, they need to fetch data from either CPU memory or remote processors. We use both self-hosted Intel Knights Landing (KNL) clusters and multi-GPU clusters as our target platforms. From an algorithm aspect, current distributed machine learningmore » systems are mainly designed for cloud systems. These methods are asynchronous because of the slow network and high fault-tolerance requirement on cloud systems. We focus on Elastic Averaging SGD (EASGD) to design algorithms for HPC clusters. Original EASGD used round-robin method for communication and updating. The communication is ordered by the machine rank ID, which is inefficient on HPC clusters. First, we redesign four efficient algorithms for HPC systems to improve EASGD's poor scaling on clusters. Async EASGD, Async MEASGD, and Hogwild EASGD are faster \\textcolor{black}{than} their existing counterparts (Async SGD, Async MSGD, and Hogwild SGD, resp.) in all the comparisons. Finally, we design Sync EASGD, which ties for the best performance among all the methods while being deterministic. In addition to the algorithmic improvements, we use some system-algorithm codesign techniques to scale up the algorithms. By reducing the percentage of communication from 87% to 14%, our Sync EASGD achieves 5.3x speedup over original EASGD on the same platform. We get 91.5% weak scaling efficiency on 4253 KNL cores, which is higher than the state-of-the-art implementation.« less

Robot-Assisted Fracture Surgery: Surgical Requirements and System Design.

PubMed

Georgilas, Ioannis; Dagnino, Giulio; Tarassoli, Payam; Atkins, Roger; Dogramadzi, Sanja

2018-03-09

The design of medical devices is a complex and crucial process to ensure patient safety. It has been shown that improperly designed devices lead to errors and associated accidents and costs. A key element for a successful design is incorporating the views of the primary and secondary stakeholders early in the development process. They provide insights into current practice and point out specific issues with the current processes and equipment in use. This work presents how information from a user-study conducted in the early stages of the RAFS (Robot Assisted Fracture Surgery) project informed the subsequent development and testing of the system. The user needs were captured using qualitative methods and converted to operational, functional, and non-functional requirements based on the methods derived from product design and development. This work presents how the requirements inform a new workflow for intra-articular joint fracture reduction using a robotic system. It is also shown how the various elements of the system are developed to explicitly address one or more of the requirements identified, and how intermediate verification tests are conducted to ensure conformity. Finally, a validation test in the form of a cadaveric trial confirms the ability of the designed system to satisfy the aims set by the original research question and the needs of the users.

High-Speed Recording of Test Data on Hard Disks

NASA Technical Reports Server (NTRS)

Lagarde, Paul M., Jr.; Newnan, Bruce

2003-01-01

Disk Recording System (DRS) is a systems-integration computer program for a direct-to-disk (DTD) high-speed data acquisition system (HDAS) that records rocket-engine test data. The HDAS consists partly of equipment originally designed for recording the data on tapes. The tape recorders were replaced with hard-disk drives, necessitating the development of DRS to provide an operating environment that ties two computers, a set of five DTD recorders, and signal-processing circuits from the original tape-recording version of the HDAS into one working system. DRS includes three subsystems: (1) one that generates a graphical user interface (GUI), on one of the computers, that serves as a main control panel; (2) one that generates a GUI, on the other computer, that serves as a remote control panel; and (3) a data-processing subsystem that performs tasks on the DTD recorders according to instructions sent from the main control panel. The software affords capabilities for dynamic configuration to record single or multiple channels from a remote source, remote starting and stopping of the recorders, indexing to prevent overwriting of data, and production of filtered frequency data from an original time-series data file.

Vehicle Systems Engineering and Integration Activities

DTIC Science & Technology

2012-08-31

of the Assistant Secretary of Defense for Research and Engineering. Its objective is to fundamentally change the capabilities for the design...Reliability Improvements for Selected Equipment) package. The standard RISE package includes an upgraded propulsion system ( turbocharged engine and...component of the RISE powertrain incorporated into the original M113A3 and M730A2 vehicles is the turbocharged 275 hp 6V53T engine from Detroit Diesel

Multidimensional modulation for next-generation transmission systems

NASA Astrophysics Data System (ADS)

Millar, David S.; Koike-Akino, Toshiaki; Kojima, Keisuke; Parsons, Kieran

2017-01-01

Recent research in multidimensional modulation has shown great promise in long reach applications. In this work, we will investigate the origins of this gain, the different approaches to multidimensional constellation design, and different performance metrics for coded modulation. We will also discuss the reason that such coded modulation schemes seem to have limited application at shorter distances, and the potential for other coded modulation schemes in future transmission systems.

Space Shuttle Navigation in the GPS Era

NASA Technical Reports Server (NTRS)

Goodman, John L.

2001-01-01

The Space Shuttle navigation architecture was originally designed in the 1970s. A variety of on-board and ground based navigation sensors and computers are used during the ascent, orbit coast, rendezvous, (including proximity operations and docking) and entry flight phases. With the advent of GPS navigation and tightly coupled GPS/INS Units employing strapdown sensors, opportunities to improve and streamline the Shuttle navigation process are being pursued. These improvements can potentially result in increased safety, reliability, and cost savings in maintenance through the replacement of older technologies and elimination of ground support systems (such as Tactical Air Control and Navigation (TACAN), Microwave Landing System (MLS) and ground radar). Selection and missionization of "off the shelf" GPS and GPS/INS units pose a unique challenge since the units in question were not originally designed for the Space Shuttle application. Various options for integrating GPS and GPS/INS units with the existing orbiter avionics system were considered in light of budget constraints, software quality concerns, and schedule limitations. An overview of Shuttle navigation methodology from 1981 to the present is given, along with how GPS and GPS/INS technology will change, or not change, the way Space Shuttle navigation is performed in the 21 5 century.

IPACS Electronics: Comments on the Original Design and Current Efforts at Langley Research Center

NASA Technical Reports Server (NTRS)

Gowdey, J. C.

1983-01-01

The development of the integrated power altitude control system (IPACS) is described. The power bridge was fabricated, and all major parts are in hand. The bridge was tested with a 1/4 HP motor for another program. The PWM, Control Logic, and upper bridge driver power supply are breadboarded and are debugged prior to starting testing on a passive load. The Hall sensor circuit for detecting rotor position is in design.

Refinement of Foam Backfill Technology for Expedient Airfield Damage Repair- Phase I: Laboratory Evaluation of Foam Materials

DTIC Science & Technology

2016-11-01

the spring of 2016. Four of these materials were commercially available. The remaining formulations were designed specifically to support this... designated by other authorized documents. DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO THE ORIGINATOR. ERDC TR-16-16 iii...The Program Manager was Jeb S. Tingle, ERDC-GSL. This work was performed by the Airfields and Pavements Branch (GMA) of the Engineering Systems

Origin and control of instability in SCR/triac three-phase motor controllers

NASA Technical Reports Server (NTRS)

Dearth, J. J.

1982-01-01

The energy savings and reactive power reduction functions initiated by the power factor controller (PFC) are discussed. A three-phase PFC with soft start is examined analytically and experimentally to determine how well it controls the open loop instability and other possible modes of instability. The detailed mechanism of the open loop instability is determined and shown to impose design constraints on the closed loop system. The design is shown to meet those constraints.

The Preliminary Design of a Standardized Spacecraft Bus for Small Tactical Satellites (Volume 2)

DTIC Science & Technology

1996-11-01

this requirement, conditions of the model need to be modified to provide some flexibility to the original solution set. In the business world this...time The mission modules modeled in the Modsat computer model are necessarily "generic" in nature to provide both flexibility in design evaluation and...methods employed during the study, the scope of the problem, the value system used to evaluate alternatives, tradeoff studies performed, modeling tools

Operational and design aspects of accelerators for medical applications

NASA Astrophysics Data System (ADS)

Schippers, Jacobus Maarten; Seidel, Mike

2015-03-01

Originally, the typical particle accelerators as well as their associated beam transport equipment were designed for particle and nuclear physics research and applications in isotope production. In the past few decades, such accelerators and related equipment have also been applied for medical use. This can be in the original physics laboratory environment, but for the past 20 years also in hospital-based or purely clinical environments for particle therapy. The most important specific requirements of accelerators for radiation therapy with protons or ions will be discussed. The focus will be on accelerator design, operational, and formal aspects. We will discuss the special requirements to reach a high reliability for patient treatments as well as an accurate delivery of the dose at the correct position in the patient using modern techniques like pencil beam scanning. It will be shown that the technical requirements, safety aspects, and required reliability of the accelerated beam differ substantially from those in a nuclear physics laboratory. It will be shown that this difference has significant implications on the safety and interlock systems. The operation of such a medical facility should be possible by nonaccelerator specialists at different operating sites (treatment rooms). The organization and role of the control and interlock systems can be considered as being the most crucially important issue, and therefore a special, dedicated design is absolutely necessary in a facility providing particle therapy.

Floating aerial 3D display based on the freeform-mirror and the improved integral imaging system

NASA Astrophysics Data System (ADS)

Yu, Xunbo; Sang, Xinzhu; Gao, Xin; Yang, Shenwu; Liu, Boyang; Chen, Duo; Yan, Binbin; Yu, Chongxiu

2018-09-01

A floating aerial three-dimensional (3D) display based on the freeform-mirror and the improved integral imaging system is demonstrated. In the traditional integral imaging (II), the distortion originating from lens aberration warps elemental images and degrades the visual effect severely. To correct the distortion of the observed pixels and to improve the image quality, a directional diffuser screen (DDS) is introduced. However, the improved integral imaging system can hardly present realistic images with the large off-screen depth, which limits floating aerial visual experience. To display the 3D image in the free space, the off-axis reflection system with the freeform-mirror is designed. By combining the improved II and the designed freeform optical element, the floating aerial 3D image is presented.

System for Estimating Horizontal Velocity During Descent

NASA Technical Reports Server (NTRS)

Johnson, Andrew; Cheng, Yang; Wilson, Reg; Goguen, Jay; Martin, Alejandro San; Leger, Chris; Matthies, Larry

2007-01-01

The descent image motion estimation system (DIMES) is a system of hardware and software, designed for original use in estimating the horizontal velocity of a spacecraft descending toward a landing on Mars. The estimated horizontal velocity is used in generating rocket-firing commands to reduce the horizontal velocity as part of an overall control scheme to minimize the landing impact. DIMES can also be used for estimating the horizontal velocity of a remotely controlled or autonomous aircraft for purposes of navigation and control.

Design analysis and computer-aided performance evaluation of shuttle orbiter electrical power system. Volume 2: SYSTID user's guide

NASA Technical Reports Server (NTRS)

1974-01-01

The manual for the use of the computer program SYSTID under the Univac operating system is presented. The computer program is used in the simulation and evaluation of the space shuttle orbiter electric power supply. The models described in the handbook are those which were available in the original versions of SYSTID. The subjects discussed are: (1) program description, (2) input language, (3) node typing, (4) problem submission, and (5) basic and power system SYSTID libraries.

An Introduction to the Solar System

NASA Astrophysics Data System (ADS)

McBride, Neil; Gilmour, Iain

2004-03-01

Compiled by a team of experts, this textbook has been designed for elementary university courses in planetary science. It starts with a tour of the Solar System and an overview of its formation that reviews in detail the terrestrial planets, giant planets and minor bodies. It concludes with a discussion of the origin of the Solar System. The text contains numerous useful learning features such as boxed summaries, student exercises with full solutions, and a glossary of terms. It is also supported by a website hosting further teaching materials.

Advanced exterior sensor project : final report, September 2004.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashby, M. Rodema

2004-12-01

This report (1) summarizes the overall design of the Advanced Exterior Sensor (AES) system to include detailed descriptions of system components, (2) describes the work accomplished throughout FY04 to evaluate the current health of the original prototype and to return it to operation, (3) describes the status of the AES and the AES project as of September 2004, and (4) details activities planned to complete modernization of the system to include development and testing of the second-generation AES prototype.

An Evidence Theoretic Approach to Design of Reliable Low-Cost UAVs

DTIC Science & Technology

2009-07-28

given period. For complex systems with various stages of missions, “ success ” becomes hard to define. For a UAV, for example, is success defined as...For this reason, the proposed methods in this thesis investigate probability of failure (PoF ) rather than probability of success . Further, failure will...reduction in system PoF . Figure 25 illustrates this; a single component 43 (A) from the original system (Figure 25a) is modified to act in a subsystem with

Integration Of Launch Vehicle Simulation/Analysis Tools And Lunar Cargo Lander Design. Part 2/2

NASA Technical Reports Server (NTRS)

DeJean, George Brian; Shiue, Yeu-Sheng Paul; King, Jeffrey

2005-01-01

Part 2, which will be discussed in this report, will discuss the development of a Lunar Cargo Lander (unmanned launch vehicle) that will transport usable payload from Trans- Lunar Injection to the moon. The Delta IV-Heavy was originally used to transport the Lunar Cargo Lander to TLI, but other launch vehicles have been studied. In order to uncover how much payload is possible to land on the moon, research was needed in order to design the sub-systems of the spacecraft. The report will discuss and compare the use of a hypergolic and cryogenic system for its main propulsion system. The guidance, navigation, control, telecommunications, thermal, propulsion, structure, mechanisms, landing gear, command, data handling, and electrical power sub-systems were designed by scaling off other flown orbiters and moon landers. Once all data was collected, an excel spreadsheet was created to accurately calculate the usable payload that will land on the moon along with detailed mass and volume estimating relations. As designed, The Lunar Cargo Lander can plant 5,400 lbm of usable payload on the moon using a hypergolic system and 7,400 lbm of usable payload on the moon using a cryogenic system.

Optimal Fault-Tolerant Control for Discrete-Time Nonlinear Strict-Feedback Systems Based on Adaptive Critic Design.

PubMed

Wang, Zhanshan; Liu, Lei; Wu, Yanming; Zhang, Huaguang

2018-06-01

This paper investigates the problem of optimal fault-tolerant control (FTC) for a class of unknown nonlinear discrete-time systems with actuator fault in the framework of adaptive critic design (ACD). A pivotal highlight is the adaptive auxiliary signal of the actuator fault, which is designed to offset the effect of the fault. The considered systems are in strict-feedback forms and involve unknown nonlinear functions, which will result in the causal problem. To solve this problem, the original nonlinear systems are transformed into a novel system by employing the diffeomorphism theory. Besides, the action neural networks (ANNs) are utilized to approximate a predefined unknown function in the backstepping design procedure. Combined the strategic utility function and the ACD technique, a reinforcement learning algorithm is proposed to set up an optimal FTC, in which the critic neural networks (CNNs) provide an approximate structure of the cost function. In this case, it not only guarantees the stability of the systems, but also achieves the optimal control performance as well. In the end, two simulation examples are used to show the effectiveness of the proposed optimal FTC strategy.

Adaptive Neural Output Feedback Control for Nonstrict-Feedback Stochastic Nonlinear Systems With Unknown Backlash-Like Hysteresis and Unknown Control Directions.

PubMed

Yu, Zhaoxu; Li, Shugang; Yu, Zhaosheng; Li, Fangfei

2018-04-01

This paper investigates the problem of output feedback adaptive stabilization for a class of nonstrict-feedback stochastic nonlinear systems with both unknown backlashlike hysteresis and unknown control directions. A new linear state transformation is applied to the original system, and then, control design for the new system becomes feasible. By combining the neural network's (NN's) parameterization, variable separation technique, and Nussbaum gain function method, an input-driven observer-based adaptive NN control scheme, which involves only one parameter to be updated, is developed for such systems. All closed-loop signals are bounded in probability and the error signals remain semiglobally bounded in the fourth moment (or mean square). Finally, the effectiveness and the applicability of the proposed control design are verified by two simulation examples.

Advanced Gas Turbine (AGT) powertrain system

NASA Technical Reports Server (NTRS)

Helms, H. E.; Kaufeld, J.; Kordes, R.

1981-01-01

A 74.5 kW(100 hp) advanced automotive gas turbine engine is described. A design iteration to improve the weight and production cost associated with the original concept is discussed. Major rig tests included 15 hours of compressor testing to 80% design speed and the results are presented. Approximately 150 hours of cold flow testing showed duct loss to be less than the design goal. Combustor test results are presented for initial checkout tests. Turbine design and rig fabrication is discussed. From a materials study of six methods to fabricate rotors, two have been selected for further effort. A discussion of all six methods is given.

Tactical 3D model generation using structure-from-motion on video from unmanned systems

NASA Astrophysics Data System (ADS)

Harguess, Josh; Bilinski, Mark; Nguyen, Kim B.; Powell, Darren

2015-05-01

Unmanned systems have been cited as one of the future enablers of all the services to assist the warfighter in dominating the battlespace. The potential benefits of unmanned systems are being closely investigated -- from providing increased and potentially stealthy surveillance, removing the warfighter from harms way, to reducing the manpower required to complete a specific job. In many instances, data obtained from an unmanned system is used sparingly, being applied only to the mission at hand. Other potential benefits to be gained from the data are overlooked and, after completion of the mission, the data is often discarded or lost. However, this data can be further exploited to offer tremendous tactical, operational, and strategic value. To show the potential value of this otherwise lost data, we designed a system that persistently stores the data in its original format from the unmanned vehicle and then generates a new, innovative data medium for further analysis. The system streams imagery and video from an unmanned system (original data format) and then constructs a 3D model (new data medium) using structure-from-motion. The 3D generated model provides warfighters additional situational awareness, tactical and strategic advantages that the original video stream lacks. We present our results using simulated unmanned vehicle data with Google Earth™providing the imagery as well as real-world data, including data captured from an unmanned aerial vehicle flight.

Aeronomy report no. 74: The Urbana meteor-radar system; design, development, and first observations

NASA Technical Reports Server (NTRS)

Hess, G. C.; Geller, M. A.

1976-01-01

The design, development, and first observations of a high power meteor-radar system located near Urbana, Illinois are described. The roughly five-fold increase in usable echo rate compared to other facilities, along with automated digital data processing and interferometry measurement of echo arrival angles, permits unsurpassed observations of tidal structure and shorter period waves. Such observations are discussed. The technique of using echo decay rates to infer density and scale height and the method of inferring wind shear from radial acceleration are examined. An original experiment to test a theory of the Delta-region winter anomaly is presented.

Experimental and Numerical Optimization of a High-Lift System to Improve Low-Speed Performance, Stability, and Control of an Arrow-Wing Supersonic Transport

NASA Technical Reports Server (NTRS)

Hahne, David E.; Glaab, Louis J.

1999-01-01

An investigation was performed to evaluate leading-and trailing-edge flap deflections for optimal aerodynamic performance of a High-Speed Civil Transport concept during takeoff and approach-to-landing conditions. The configuration used for this study was designed by the Douglas Aircraft Company during the 1970's. A 0.1-scale model of this configuration was tested in the Langley 30- by 60-Foot Tunnel with both the original leading-edge flap system and a new leading-edge flap system, which was designed with modem computational flow analysis and optimization tools. Leading-and trailing-edge flap deflections were generated for the original and modified leading-edge flap systems with the computational flow analysis and optimization tools. Although wind tunnel data indicated improvements in aerodynamic performance for the analytically derived flap deflections for both leading-edge flap systems, perturbations of the analytically derived leading-edge flap deflections yielded significant additional improvements in aerodynamic performance. In addition to the aerodynamic performance optimization testing, stability and control data were also obtained. An evaluation of the crosswind landing capability of the aircraft configuration revealed that insufficient lateral control existed as a result of high levels of lateral stability. Deflection of the leading-and trailing-edge flaps improved the crosswind landing capability of the vehicle considerably; however, additional improvements are required.

New controller for high voltage converter modulator at spallation neutron source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wezensky, Mark W; Brown, David L; Lee, Sung-Woo

2017-01-01

The Spallation Neutron Source (SNS) has developed a new control system for the High Voltage Convertor Modulator (HVCM) at the SNS to replace the original control system which is approaching obsolescence. The original system was based on controllers for similar high voltage systems that were already in use [1]. The new controller, based on National Instruments PXI/FlexRIO Field Programmable Gate Array (FPGA) platform, offers enhancements such as modular construction, flexibility and non-proprietary software. The new controller also provides new capabilities like various methods for modulator pulse flattening, waveform capture, and first fault detection. This paper will discuss the design ofmore » the system, including the human machine interface, based on lessons learned at the SNS and other projects. It will also discuss performance and other issues related to its operation in an accelerator facility which requires high availability. To date, 73% of the operational HVCMs have been upgraded to with the new controller, and the remainder are scheduled for completion by mid-2017.« less

Extrasolar Planet Inferometric Survey (EPIcS)

NASA Technical Reports Server (NTRS)

Shao, Michael; Baliunas, Sallie; Boden, Andrew; Kulkarni, Shrinivas; Lin, Douglas N. C.; Loredo, Tom; Queloz, Didier; Shaklan, Stuart; Tremaine, Scott; Wolszczan, Alexander

2004-01-01

The discovery of the nature of the solar system was a crowning achievement of Renaissance science. The quest to evaluate the properties of extrasolar planetary systems is central to both the intellectual understanding of our origins and the cultural understanding of humanity's place in the Universe; thus it is appropriate that the goals and objectives of NASA's breakthrough Origins program emphasize the study of planetary systems, with a focus on the search for habitable planets. We propose an ambitious research program that will use SIM - the first major mission of the Origins program - to explore planetary systems in our Galactic neighborhood. Our program is a novel two-tiered SIM survey of nearby stars that exploits the capabilities of SIM to achieve two scientific objectives: (i) to identify Earth-like planets in habitable regions around nearby Sunlike stars: and (ii) to explore the nature and evolution of planetary systems in their full variety. The first of these objectives was recently recommended by the Astronomy and Astrophysics Survey Committee (the McKee-Taylor Committee) as a prerequisite for the development of the Terrestrial Planet Finder mission later in the decade. Our program combines this two-part survey with preparatory and contemporaneous research designed to maximize the scientific return from the limited and thus precious observing resources of SIM.

Design of two-dimensional zero reference codes with cross-entropy method.

PubMed

Chen, Jung-Chieh; Wen, Chao-Kai

2010-06-20

We present a cross-entropy (CE)-based method for the design of optimum two-dimensional (2D) zero reference codes (ZRCs) in order to generate a zero reference signal for a grating measurement system and achieve absolute position, a coordinate origin, or a machine home position. In the absence of diffraction effects, the 2D ZRC design problem is known as the autocorrelation approximation. Based on the properties of the autocorrelation function, the design of the 2D ZRC is first formulated as a particular combination optimization problem. The CE method is then applied to search for an optimal 2D ZRC and thus obtain the desirable zero reference signal. Computer simulation results indicate that there are 15.38% and 14.29% reductions in the second maxima value for the 16x16 grating system with n(1)=64 and the 100x100 grating system with n(1)=300, respectively, where n(1) is the number of transparent pixels, compared with those of the conventional genetic algorithm.

7. Historic American Buildings Survey ORIGINAL DESIGN SUBMITTED BY PEABODY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. Historic American Buildings Survey ORIGINAL DESIGN SUBMITTED BY PEABODY AND STEARNS (FROM THE ORIGINAL IN THE LIBRARY OF THE VOLTA BUREAU) - Volta Bureau, 1537 Thirty-fifth Street Northwest, Washington, District of Columbia, DC

Flip-Flop Recovery System for sounding rocket payloads

NASA Technical Reports Server (NTRS)

Flores, A., Jr.

1986-01-01

The design, development, and testing of the Flip-Flop Recovery System, which protects sensitive forward-mounted instruments from ground impact during sounding rocket payload recovery operations, are discussed. The system was originally developed to reduce the impact damage to the expensive gold-plated forward-mounted spectrometers in two existing Taurus-Orion rocket payloads. The concept of the recovery system is simple: the payload is flipped over end-for-end at a predetermined time just after parachute deployment, thus minimizing the risk of damage to the sensitive forward portion of the payload from ground impact.

The F-92 RELIANT: Air transport system design simulation

NASA Technical Reports Server (NTRS)

1992-01-01

The design proposal of a semester long design project by group 'F' for AE 441 is addressed. In formulating this design, the driving philosophy was not just to fulfill the mission requirements (discussed in chapter two), but to do so in a creative manner - this explains the unconventional aircraft design, named the F-92 RELIANT. Although unconventional, and perhaps more expensive to produce, the design has distinct advantages which could only be attained through such a creative design. Major components of the F-92 Reliant include: (1) unobstructed cargo bay, 1024 cu. in. capability; (2) loading ramp; (3) dual wing configuration; and (4) polyhedral wing configuration. These design components either originated or evolved to create an aircraft that would most effectively meet the goals of cargo transportation in AeroWorld at minimum cost.

A knowledge based search tool for performance measures in health care systems.

PubMed

Beyan, Oya D; Baykal, Nazife

2012-02-01

Performance measurement is vital for improving the health care systems. However, we are still far from having accepted performance measurement models. Researchers and developers are seeking comparable performance indicators. We developed an intelligent search tool to identify appropriate measures for specific requirements by matching diverse care settings. We reviewed the literature and analyzed 229 performance measurement studies published after 2000. These studies are evaluated with an original theoretical framework and stored in the database. A semantic network is designed for representing domain knowledge and supporting reasoning. We have applied knowledge based decision support techniques to cope with uncertainty problems. As a result we designed a tool which simplifies the performance indicator search process and provides most relevant indicators by employing knowledge based systems.

An air bearing system for small high speed gas turbines

NASA Astrophysics Data System (ADS)

Turner, A. B.; Davies, S. J.; Nimir, Y. L.

1994-03-01

This paper describes the second phase of an experimental program concerning the application of air bearings to small turbomachinery test rigs and small gas turbines. The first phase examined externally pressurized (EP) journal bearings, with a novel EP thrust bearing, for application to 'warm air' test rigs, and was entirely successful at rotational speeds in excess of 100,000 rpm. This second phase examined several designs of tilting pad-spiring journal bearings, one with a novel form of externally pressurized pad, but all using the original EP thrust bearing. The designs tested are described, including some oscillogram traces, for tests up to a maximum of 70,000 rpm; the most successful using a carbon pad-titanium beam spring arrangement. The thrust bearing which gave trouble-free operation throughout, is also described. The results of an original experiment to measure the 'runway speed' of a radial inflow turbine are also presented, which show that overspeeds of 58 percent above the design speed can result from free-power turbine coupling failure.

Investigation of "6X" Scramjet Inlet Configurations

NASA Technical Reports Server (NTRS)

Alter, Stephen J.

2012-01-01

This work represents an initial attempt to determine what, if any, issues arise from scaling demonstration supersonic combustion scramjets to a flight scale making the engine a viable candidate for both military weapon and civilian access to space applications. The original vehicle sizes tested and flown to date, were designed to prove a concept. With the proven designs, use of the technology for applications as weapon systems or space flight are only possible at six to ten times the original scale. To determine effects of scaling, computations were performed with hypersonic inlets designed to operate a nominal Mach 4 and Mach 5 conditions that are possible within the eight foot high temperature tunnel at NASA Langley Research Center. The total pressure recovery for these inlets is about 70%, while maintaining self start conditions, and providing operable inflow to combustors. Based on this study, the primary scaling effect detected is the strength of a vortex created along the cowl edge causing adverse boundary layer growth in the inlet.

System engineering techniques for establishing balanced design and performance guidelines for the advanced telerobotic testbed

NASA Technical Reports Server (NTRS)

Zimmerman, W. F.; Matijevic, J. R.

1987-01-01

Novel system engineering techniques have been developed and applied to establishing structured design and performance objectives for the Telerobotics Testbed that reduce technical risk while still allowing the testbed to demonstrate an advancement in state-of-the-art robotic technologies. To estblish the appropriate tradeoff structure and balance of technology performance against technical risk, an analytical data base was developed which drew on: (1) automation/robot-technology availability projections, (2) typical or potential application mission task sets, (3) performance simulations, (4) project schedule constraints, and (5) project funding constraints. Design tradeoffs and configuration/performance iterations were conducted by comparing feasible technology/task set configurations against schedule/budget constraints as well as original program target technology objectives. The final system configuration, task set, and technology set reflected a balanced advancement in state-of-the-art robotic technologies, while meeting programmatic objectives and schedule/cost constraints.

Dead simple OWL design patterns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osumi-Sutherland, David; Courtot, Melanie; Balhoff, James P.

Bio-ontologies typically require multiple axes of classification to support the needs of their users. Development of such ontologies can only be made scalable and sustainable by the use of inference to automate classification via consistent patterns of axiomatization. Many bio-ontologies originating in OBO or OWL follow this approach. These patterns need to be documented in a form that requires minimal expertise to understand and edit and that can be validated and applied using any of the various programmatic approaches to working with OWL ontologies. We describe a system, Dead Simple OWL Design Patterns (DOS-DPs), which fulfills these requirements, illustrating themore » system with examples from the Gene Ontology. In conclusion, the rapid adoption of DOS-DPs by multiple ontology development projects illustrates both the ease-of use and the pressing need for the simple design pattern system we have developed.« less

Dead simple OWL design patterns

DOE PAGES

Osumi-Sutherland, David; Courtot, Melanie; Balhoff, James P.; ...

2017-06-05

Bio-ontologies typically require multiple axes of classification to support the needs of their users. Development of such ontologies can only be made scalable and sustainable by the use of inference to automate classification via consistent patterns of axiomatization. Many bio-ontologies originating in OBO or OWL follow this approach. These patterns need to be documented in a form that requires minimal expertise to understand and edit and that can be validated and applied using any of the various programmatic approaches to working with OWL ontologies. We describe a system, Dead Simple OWL Design Patterns (DOS-DPs), which fulfills these requirements, illustrating themore » system with examples from the Gene Ontology. In conclusion, the rapid adoption of DOS-DPs by multiple ontology development projects illustrates both the ease-of use and the pressing need for the simple design pattern system we have developed.« less

Engineering based assessment for a shape design of a pediatric ePTFE pulmonary conduit valve.

PubMed

Tsuboko, Yusuke; Shiraishi, Yasuyuki; Yamada, Akihiro; Yambe, Tomoyuki; Miura, Hidekazu; Mura, Seitaro; Yamagishi, Masaaki

2016-08-01

The authors examined the hemodynamic characteristics of expanded polytetrafluoroethylene (ePTFE) pulmonary valved conduits quantitatively by our originally developed pediatric pulmonary mechanical circulatory system, in order to suggest the optimal shape design. The system consisted of pneumatically driven right atrium and ventricle model, a pulmonary valve chamber, and elastic pulmonary compliance model with peripheral vascular resistance units, a venous reservoir. We employed two different types of ePTFE valve and evaluated the relationship between the leaflets motion and hemodynamic characteristics by using a high-speed video camera. As a result, we successfully reproduced hemodynamic simulations in our pediatric pulmonary mock system. We confirmed that the presence of bulging sinuses in the pulmonary valved conduit reduced the transvalvular energy loss and increased the valve opening area during systolic period. Our engineering-based in vitro analysis could be useful for proposing a shape design optimization of sophisticated pediatric ePTFE pulmonary valve.

HDL-level automated watermarking of IP cores

NASA Astrophysics Data System (ADS)

Castillo, E.; Meyer-Baese, U.; Parrilla, L.; García, A.; Lloris, A.

2008-04-01

This paper presents significant improvements to our previous watermarking technique for Intellectual Property Protection (IPP) of IP cores. The technique relies on hosting the bits of a digital signature at the HDL design level using resources included within the original system. Thus, any attack trying to change or remove the digital signature will damage the design. The technique also includes a procedure for secure signature extraction requiring minimal modifications to the system. The new advances refer to increasing the applicability of this watermarking technique to any design, not only to those including look-ups, and the provision of an automatic tool for signature hosting purposes. Synthesis results show that the application of the proposed watermarking strategy results in negligible degradation of system performance and very low area penalties and that the use of the automated tool, in addition to easy the signature hosting, leads to reduced area penalties.

Piloted simulation of one-on-one helicopter air combat at NOE flight levels

NASA Technical Reports Server (NTRS)

Lewis, M. S.; Aiken, E. W.

1985-01-01

A piloted simulation designed to examine the effects of terrain proximity and control system design on helicopter performance during one-on-one air combat maneuvering (ACM) is discussed. The NASA Ames vertical motion simulator (VMS) and the computer generated imagery (CGI) systems were modified to allow two aircraft to be independently piloted on a single CGI data base. Engagements were begun with the blue aircraft already in a tail-chase position behind the red, and also with the two aircraft originating from positions unknown to each other. Maneuvering was very aggressive and safety requirements for minimum altitude, separation, and maximum bank angles typical of flight test were not used. Results indicate that the presence of terrain features adds an order of complexiaty to the task performed over clear air ACM and that mix of attitude and rate command-type stability and control augmentation system (SCAS) design may be desirable. The simulation system design, the flight paths flown, and the tactics used were compared favorably by the evaluation pilots to actual flight test experiments.

DSN 70-meter antenna microwave optics design and performance improvements. Part 1: Design optimization

NASA Technical Reports Server (NTRS)

Bathker, D. A.; Slobin, S. D.

1989-01-01

The design optimizations associated with the microwave and structural upgrade of the DSN 64-m antennas are discussed. Expected area efficiency/gain performances at S- and X-band are given for both the original 64-m systems and the upgraded 70-m systems, and error estimates are developed. The DSN 70-m Upgrade Project specifications, based on predesign estimates, were 1.4-dB gain at S-band and 1.9-dB at X-band, with no degradation to critical receiving system noise temperatures. The measurements show an S-band gain increase of 1.9 dB and an average increase of 2.1 dB at X-band. The Project also delivered small receiving system noise decreases at both frequency bands. The three DSN 70-m antennas, in the initial state of mechanical adjustment as of the end of calendar year 1988, are performing with very high peak microwave area efficiencies at very nearly the engineering design expectations of 76 percent at S-band and 71 percent at X-band.

Design and implementation of an improved chilled water glycol system for NICI array electronics thermal enclosure

NASA Astrophysics Data System (ADS)

Gausachs, Gaston

2008-07-01

The Near Infrared Chronographic Imager (NICI) being commissioned at Gemini was upgraded with a more powerful Chilled Water Glycol System to address early overheating problems. The previous system was replaced with a completely new design favoring improved airflow and increased heat transfer capabilities. The research leading to this upgrade showed a significant lack of cooling power of the original design. The solution was a combination of commercial heat exchanger and fans and a custom built enclosure. As a prime infrared telescope facility, Gemini is very much interested in maintaining the least amount of heat dissipated to the ambient air. The results obtained through the implementation of this solution will be helpful in understanding the state of other existing electronics enclosures as well as those for new instruments to come. With the advent of electronic intensive AO systems, future electronics enclosures must take full advantage of improved cooling. This paper describes the design and implementation phases of the project. The results under maximum operating capacity proved to be within the expected theoretical values and were deemed successful.

Generating a Double-Scroll Attractor by Connecting a Pair of Mutual Mirror-Image Attractors via Planar Switching Control

NASA Astrophysics Data System (ADS)

Sun, Changchun; Chen, Zhongtang; Xu, Qicheng

2017-12-01

An original three-dimensional (3D) smooth continuous chaotic system and its mirror-image system with eight common parameters are constructed and a pair of symmetric chaotic attractors can be generated simultaneously. Basic dynamical behaviors of two 3D chaotic systems are investigated respectively. A double-scroll chaotic attractor by connecting the pair of mutual mirror-image attractors is generated via a novel planar switching control approach. Chaos can also be controlled to a fixed point, a periodic orbit and a divergent orbit respectively by switching between two chaotic systems. Finally, an equivalent 3D chaotic system by combining two 3D chaotic systems with a switching law is designed by utilizing a sign function. Two circuit diagrams for realizing the double-scroll attractor are depicted by employing an improved module-based design approach.

Policy Driven Development: Flexible Policy Insertion for Large Scale Systems.

PubMed

Demchak, Barry; Krüger, Ingolf

2012-07-01

The success of a software system depends critically on how well it reflects and adapts to stakeholder requirements. Traditional development methods often frustrate stakeholders by creating long latencies between requirement articulation and system deployment, especially in large scale systems. One source of latency is the maintenance of policy decisions encoded directly into system workflows at development time, including those involving access control and feature set selection. We created the Policy Driven Development (PDD) methodology to address these development latencies by enabling the flexible injection of decision points into existing workflows at runtime , thus enabling policy composition that integrates requirements furnished by multiple, oblivious stakeholder groups. Using PDD, we designed and implemented a production cyberinfrastructure that demonstrates policy and workflow injection that quickly implements stakeholder requirements, including features not contemplated in the original system design. PDD provides a path to quickly and cost effectively evolve such applications over a long lifetime.

Multiparameter optimization of mammography: an update

NASA Astrophysics Data System (ADS)

Jafroudi, Hamid; Muntz, E. P.; Jennings, Robert J.

1994-05-01

Previously in this forum we have reported the application of multiparameter optimization techniques to the design of a minimum dose mammography system. The approach used a reference system to define the physical imaging performance required and the dose to which the dose for the optimized system should be compared. During the course of implementing the resulting design in hardware suitable for laboratory testing, the state of the art in mammographic imaging changed, so that the original reference system, which did not have a grid, was no longer appropriate. A reference system with a grid was selected in response to this change, and at the same time the optimization procedure was modified, to make it more general and to facilitate study of the optimized design under a variety of conditions. We report the changes in the procedure, and the results obtained using the revised procedure and the up- to-date reference system. Our results, which are supported by laboratory measurements, indicate that the optimized design can image small objects as well as the reference system using only about 30% of the dose required by the reference system. Hardware meeting the specification produced by the optimization procedure and suitable for clinical use is currently under evaluation in the Diagnostic Radiology Department at the Clinical Center, NH.

Reformulation of a clinical-dose system for carbon-ion radiotherapy treatment planning at the National Institute of Radiological Sciences, Japan

NASA Astrophysics Data System (ADS)

Inaniwa, Taku; Kanematsu, Nobuyuki; Matsufuji, Naruhiro; Kanai, Tatsuaki; Shirai, Toshiyuki; Noda, Koji; Tsuji, Hiroshi; Kamada, Tadashi; Tsujii, Hirohiko

2015-04-01

At the National Institute of Radiological Sciences (NIRS), more than 8,000 patients have been treated for various tumors with carbon-ion (C-ion) radiotherapy in the past 20 years based on a radiobiologically defined clinical-dose system. Through clinical experience, including extensive dose escalation studies, optimum dose-fractionation protocols have been established for respective tumors, which may be considered as the standards in C-ion radiotherapy. Although the therapeutic appropriateness of the clinical-dose system has been widely demonstrated by clinical results, the system incorporates several oversimplifications such as dose-independent relative biological effectiveness (RBE), empirical nuclear fragmentation model, and use of dose-averaged linear energy transfer to represent the spectrum of particles. We took the opportunity to update the clinical-dose system at the time we started clinical treatment with pencil beam scanning, a new beam delivery method, in 2011. The requirements for the updated system were to correct the oversimplifications made in the original system, while harmonizing with the original system to maintain the established dose-fractionation protocols. In the updated system, the radiation quality of the therapeutic C-ion beam was derived with Monte Carlo simulations, and its biological effectiveness was predicted with a theoretical model. We selected the most used C-ion beam with αr = 0.764 Gy-1 and β = 0.0615 Gy-2 as reference radiation for RBE. The C-equivalent biological dose distribution is designed to allow the prescribed survival of tumor cells of the human salivary gland (HSG) in entire spread-out Bragg peak (SOBP) region, with consideration to the dose dependence of the RBE. This C-equivalent biological dose distribution is scaled to a clinical dose distribution to harmonize with our clinical experiences with C-ion radiotherapy. Treatment plans were made with the original and the updated clinical-dose systems, and both physical and clinical dose distributions were compared with regard to the prescribed dose level, beam energy, and SOBP width. Both systems provided uniform clinical dose distributions within the targets consistent with the prescriptions. The mean physical doses delivered to targets by the updated system agreed with the doses by the original system within ±1.5% for all tested conditions. The updated system reflects the physical and biological characteristics of the therapeutic C-ion beam more accurately than the original system, while at the same time allowing the continued use of the dose-fractionation protocols established with the original system at NIRS.

Exploration of near the origin and the asymptotic behaviors of the Kohn-Sham kinetic energy density for two-dimensional quantum dot systems with parabolic confinement

NASA Astrophysics Data System (ADS)

Jana, Subrata; Samal, Prasanjit

2018-01-01

The behaviors of the positive definite Kohn-Sham kinetic energy density near the origin and at the asymptotic region play a major role in designing meta-generalized gradient approximations (meta-GGAs) for exchange in low-dimensional quantum systems. It is shown that near the origin of the parabolic quantum dot, the Kohn-Sham kinetic energy differs from its von Weizsäcker counterpart due to the p orbital contributions, whereas in the asymptotic region, the difference between the above two kinetic energy densities goes as ˜ρ/(r ) r2 . All these behaviors have been explored using the two-dimensional isotropic quantum harmonic oscillator as a test case. Several meta-GGA ingredients are then studied by making use of the above findings. Also, the asymptotic conditions for the exchange energy density and the potential at the meta-GGA level are proposed using the corresponding behaviors of the two kinetic energy densities.

Exploration of near the origin and the asymptotic behaviors of the Kohn-Sham kinetic energy density for two-dimensional quantum dot systems with parabolic confinement.

PubMed

Jana, Subrata; Samal, Prasanjit

2018-01-14

The behaviors of the positive definite Kohn-Sham kinetic energy density near the origin and at the asymptotic region play a major role in designing meta-generalized gradient approximations (meta-GGAs) for exchange in low-dimensional quantum systems. It is shown that near the origin of the parabolic quantum dot, the Kohn-Sham kinetic energy differs from its von Weizsäcker counterpart due to the p orbital contributions, whereas in the asymptotic region, the difference between the above two kinetic energy densities goes as ∼ρ(r)r 2 . All these behaviors have been explored using the two-dimensional isotropic quantum harmonic oscillator as a test case. Several meta-GGA ingredients are then studied by making use of the above findings. Also, the asymptotic conditions for the exchange energy density and the potential at the meta-GGA level are proposed using the corresponding behaviors of the two kinetic energy densities.

B-70 Aircraft Study. Volume 2

NASA Technical Reports Server (NTRS)

1972-01-01

Volume 2 of the final report on the B-70 aircraft study is presented here. The B-70 Program, at the onset, was a full weapon system capable of sustained Mach 3 flight for the major portion of its design missions. The weapon system was to enter the SAC inventory as an RS-70 with the first intercontinental resonnaissance/bomber wing scheduled to go operational in July, 1964. After several redirections, a two XB-70 air vehicle program emerged with its prime objective being to demonstrate the technical feasibility of sustained Mach 3 flight. This section describes the original Weapon System 110A concepts, the evolution of the RS-70 design, and the XB-70 air vehicles which demonstrated the design, fabrication, and technical feasibility of long range Mach 3 flights at high altitude. The data presented shows that a very large step forward in the state-of-the-art of manned aircraft design was achieved during the B-70 development program and that advances were made and incorporated in every area, including design, materials application, and manufacturing techniques.

Data processing system for the Sneg-2MP experiment

NASA Technical Reports Server (NTRS)

Gavrilova, Y. A.

1980-01-01

The data processing system for scientific experiments on stations of the "Prognoz" type provides for the processing sequence to be broken down into a number of consecutive stages: preliminary processing, primary processing, secondary processing. The tasks of each data processing stage are examined for an experiment designed to study gamma flashes of galactic origin and solar flares lasting from several minutes to seconds in the 20 kev to 1000 kev energy range.

Note: The design of thin gap chamber simulation signal source based on field programmable gate array.

PubMed

Hu, Kun; Lu, Houbing; Wang, Xu; Li, Feng; Liang, Futian; Jin, Ge

2015-01-01

The Thin Gap Chamber (TGC) is an important part of ATLAS detector and LHC accelerator. Targeting the feature of the output signal of TGC detector, we have designed a simulation signal source. The core of the design is based on field programmable gate array, randomly outputting 256-channel simulation signals. The signal is generated by true random number generator. The source of randomness originates from the timing jitter in ring oscillators. The experimental results show that the random number is uniform in histogram, and the whole system has high reliability.

An Innovation in Building Design

NASA Astrophysics Data System (ADS)

1980-01-01

Collins & Aikman's flat cable permits elimination of ducts and other accommodations traditionally required for building wiring systems, thus gives designers new latitude in planning attractive "open landscape" office layouts. The big factor is that FCC, whose thickness approximates that of two business cards, can be mounted on walls and floors instead of in them, and can be installed beneath a carpet or along a baseboard. Originating from Apollo's command module, its essential sheathing is designed to look like decor rather than plumbing. This could possibly eliminate traditional ducting under floors and elsewhere necessary to accommodate conventional wiring. Construction costs are reduced by 14 percent.

Note: The design of thin gap chamber simulation signal source based on field programmable gate array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Kun; Wang, Xu; Li, Feng

The Thin Gap Chamber (TGC) is an important part of ATLAS detector and LHC accelerator. Targeting the feature of the output signal of TGC detector, we have designed a simulation signal source. The core of the design is based on field programmable gate array, randomly outputting 256-channel simulation signals. The signal is generated by true random number generator. The source of randomness originates from the timing jitter in ring oscillators. The experimental results show that the random number is uniform in histogram, and the whole system has high reliability.

Tale of Two Databases: The History of Federally Funded Information Systems for Education and Medicine

ERIC Educational Resources Information Center

Weiner, Sharon A.

2009-01-01

Access to scholarly information in the disciplines of education and medicine occurred primarily through the simultaneous development of two bibliographic databases. The Education Resource Information Center (ERIC) originated as a resource designed to be comprehensive in its inclusion of peer-reviewed and unpublished literature for the entire…

The Land-Grant Tradition

ERIC Educational Resources Information Center

National Association of State Universities and Land-Grant Colleges, 2008

2008-01-01

This document provides an overview and history of the land-grant system, as well as copies of the original and amended legislation affecting the land-grant colleges. Land-grant colleges or universities have been designated by their state legislatures or Congress to receive the benefits of the Morrill Acts of 1862, 1890 and 1994. The original…

Applying Various Comprehension Strategies. Learning Package No. 8.

ERIC Educational Resources Information Center

Simic, Marge; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on applying various comprehension strategies is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Cultural Literacy. Learning Package No. 44.

ERIC Educational Resources Information Center

Hong, Zhang, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on cultural literacy is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

The Design of an Intelligent Decision Support Tool for Submarine Commanders

DTIC Science & Technology

2009-06-01

for public release, distribution unlimited 13. SUPPLEMENTARY NOTES The original document contains color images . 14. ABSTRACT 15. SUBJECT TERMS 16...with research supporting the advancement of military technology. Thank you again for your support throughout this process . To Dave Silvia and Carl...26 2.1.3 Voyage Management System

Spatial application of WEPS for estimating wind erosion in the Pacific Northwest

USDA-ARS?s Scientific Manuscript database

The Wind Erosion Prediction System (WEPS) is used to simulate soil erosion on croplands and was originally designed to run field scale simulations. This research is an extension of the WEPS model to run on multiple fields (grids) covering a larger region. We modified the WEPS source code to allow it...

Spatial application of WEPS for estimating wind erosion in the Pacific Northwest

USDA-ARS?s Scientific Manuscript database

The Wind Erosion Prediction System (WEPS) is used to simulate soil erosion on cropland and was originally designed to run simulations on a field-scale size. This study extended WEPS to run on multiple fields (grids) independently to cover a large region and to conduct an initial investigation to ass...

Year 3 ASK/FOSS Efficacy Study. CRESST Report 782

ERIC Educational Resources Information Center

Osmundson, Ellen; Dai, Yunyun; Herman, Joan

2011-01-01

This efficacy study was designed to examine the traditional FOSS curriculum (Delta Publishing, Full Option Science System/FOSS, magnetism and electricity, structures of life, and water modules, 2005), and the new ASK/FOSS curriculum (magnetism and electricity, structures of life, and water modules, 2005), a revised version of the original FOSS…

Development of Assessment Tools To Measure Organizational Support for Employee Health.

ERIC Educational Resources Information Center

Golaszewski, Thomas; Barr, Donald; Pronk, Nico

2003-01-01

Describes one working group's attempts to develop and utilize assessment tools for measuring and changing organizational support for employee health. Originally designed as part of a heart health related intervention, the system has evolved into a managed care evaluation and major chronic disease inventory. Findings indicate the potential of…

The interplanetary pioneers. Volume 1: Summary

NASA Technical Reports Server (NTRS)

Corliss, W. R.

1972-01-01

The Pioneer Space Probe Project is explained to document the events which occurred during the project. The subjects discussed are: (1) origin and history of interplanetary Pioneer program, (2) Pioneer system development and design, (3) Pioneer flight operations, and (4) Pioneer scientific results. Line drawings, circuit diagrams, illustrations, and photographs are included to augment the written material.

A "Language" of Modernization: Culture and Art Education in the Village Institutes

ERIC Educational Resources Information Center

Kaynar, Mete Kaan; Ak, Gökhan

2017-01-01

The Village Institutes were originally-designed in-place-training institutions of the Turkish education history. They had been a very significant and unique educational-product of Turkey which were gifted to all secular [modern] world education systems. Because these Institutes were explored in line with thoroughly native considerations and…

Inland Resupply Without a Road or Runway: Airdrop Solutions Including High-Altitude Precision Systems

DTIC Science & Technology

2008-03-01

consider the origin of the parachute they probably envision the pyramidal drawing of Leonardo da Vinci from the late 1400s. However, the Chinese are...refining their designs. Like da Vinci’s plan, most had a rigid frame limiting their versatility. The practical use for the parachute was

Feeding Behaviors in Cellular Slime Molds: A Microbial System To Study Competition.

ERIC Educational Resources Information Center

Bozzone, Donna M.

1997-01-01

Describes a laboratory project for first-year biology students that examines competition among various cellular slime molds. After a brief introduction to the topic of competition and basic life history information about cellular slime molds, students choose a question and design original experiments to seek an answer. (Author/AIM)

Access to the General Curriculum: Systems Change or Tinker Some More?

ERIC Educational Resources Information Center

Sailor, Wayne

2009-01-01

Special education as practiced today remains firmly anchored in the original logic of the Amendments to the Education of the Handicapped Act (PL 94-142). Subsequent reauthorizations of the statute have included language designed to increase access to the general curriculum by special needs students but have not addressed the underlying…

Journal Writing. Learning Package No. 34.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on journal writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

Learning the Structure of English by Means of Esperanto.

ERIC Educational Resources Information Center

Jones, R. Kent

The Esperanto language was consciously designed as a coherent system, in contrast to the 3000 conventional languages originated by people's cave-dwelling ancestors. The systematic nature of Esperanto makes it ideal as an instructional tool. The amorphous nature of English makes its serious use very difficult for students. Even though they learn to…

Origins Space Telescope

NASA Astrophysics Data System (ADS)

Cooray, Asantha R.; Origins Space Telescope Study Team

2017-01-01

The Origins Space Telescope (OST) is the mission concept for the Far-Infrared Surveyor, a study in development by NASA in preparation for the 2020 Astronomy and Astrophysics Decadal Survey. Origins is planned to be a large aperture, actively-cooled telescope covering a wide span of the mid- to far-infrared spectrum. Its spectrographs will enable 3D surveys of the sky that will discover and characterize the most distant galaxies, Milky-Way, exoplanets, and the outer reaches of our Solar system. Origins will enable flagship-quality general observing programs led by the astronomical community in the 2030s. The Science and Technology Definition Team (STDT) would like to hear your science needs and ideas for this mission. The team can be contacted at firsurveyor_info@lists.ipac.caltech.edu. I will summarize the OST STDT, mission design and instruments, key science drivers, and the study plan over the next two years.

Adaptive neural network output feedback control for stochastic nonlinear systems with unknown dead-zone and unmodeled dynamics.

PubMed

Tong, Shaocheng; Wang, Tong; Li, Yongming; Zhang, Huaguang

2014-06-01

This paper discusses the problem of adaptive neural network output feedback control for a class of stochastic nonlinear strict-feedback systems. The concerned systems have certain characteristics, such as unknown nonlinear uncertainties, unknown dead-zones, unmodeled dynamics and without the direct measurements of state variables. In this paper, the neural networks (NNs) are employed to approximate the unknown nonlinear uncertainties, and then by representing the dead-zone as a time-varying system with a bounded disturbance. An NN state observer is designed to estimate the unmeasured states. Based on both backstepping design technique and a stochastic small-gain theorem, a robust adaptive NN output feedback control scheme is developed. It is proved that all the variables involved in the closed-loop system are input-state-practically stable in probability, and also have robustness to the unmodeled dynamics. Meanwhile, the observer errors and the output of the system can be regulated to a small neighborhood of the origin by selecting appropriate design parameters. Simulation examples are also provided to illustrate the effectiveness of the proposed approach.

X-15 Hardware Design Challenges

NASA Technical Reports Server (NTRS)

Storms, Harrison A., Jr.

1991-01-01

Historical events in the development of the X-15 hardware design are presented. Some of the topics covered include: (1) drivers that led to the development of the X-15; (2) X-15 space research objectives; (3) original performance targets; (4) the X-15 typical mission; (5) X-15 dimensions and weight; (5) the propulsion system; (6) X-15 development milestones; (7) engineering and manufacturing challenges; (8) the X-15 structure; (9) ballistic flight control; (10) landing gear; (11) nose gear; and (12) an X-15 program recap.

LLE 1995 annual report, October 1994--September 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-01-01

The fiscal year ending September 1995 (FY95) concluded the third year of the cooperative agreement (DE-FC03-92SF19460) with the U.S. Department of Energy (DOE). This report summarizes research at the Laboratory for Laser Energetics (LLE) and reports on the successful completion of the OMEGA Upgrade. Previous annual reports describe the OMEGA Upgrade design. The preliminary design for the system was complete in October 1989 and the detailed design started in October 1990. The original 24-beam OMEGA system was decommissioned in December 1992 as construction for the OMEGA Upgrade began. We discuss the initial performance results (p. 99) of the upgraded OMEGAmore » laser system. All acceptance tests were completed, and we demonstrated that all 60 beams can irradiate a target with more energy and better beam balance than was required by DOE`s acceptance criteria. We are most proud that all program milestones were met or exceeded, and that the system was completed on time and on budget.« less

Dual-Use Aspects of System Health Management

NASA Technical Reports Server (NTRS)

Owens, P. R.; Jambor, B. J.; Eger, G. W.; Clark, W. A.

1994-01-01

System Health Management functionality is an essential part of any space launch system. Health management functionality is an integral part of mission reliability, since it is needed to verify the reliability before the mission starts. Health Management is also a key factor in life cycle cost reduction and in increasing system availability. The degree of coverage needed by the system and the degree of coverage made available at a reasonable cost are critical parameters of a successful design. These problems are not unique to the launch vehicle world. In particular, the Intelligent Vehicle Highway System, commercial aircraft systems, train systems, and many types of industrial production facilities require various degrees of system health management. In all of these applications, too, the designers must balance the benefits and costs of health management in order to optimize costs. The importance of an integrated system is emphasized. That is, we present the case for considering health management as an integral part of system design, rather than functionality to be added on at the end of the design process. The importance of maintaining the system viewpoint is discussed in making hardware and software tradeoffs and in arriving at design decisions. We describe an approach to determine the parameters to be monitored in any system health management application. This approach is based on Design of Experiments (DOE), prototyping, failure modes and effects analyses, cost modeling and discrete event simulation. The various computer-based tools that facilitate the approach are discussed. The approach described originally was used to develop a fault tolerant avionics architecture for launch vehicles that incorporated health management as an integral part of the system. Finally, we discuss generalizing the technique to apply it to other domains. Several illustrations are presented.

VA's Integrated Imaging System on three platforms.

PubMed

Dayhoff, R E; Maloney, D L; Majurski, W J

1992-01-01

The DHCP Integrated Imaging System provides users with integrated patient data including text, image and graphics data. This system has been transferred from its original two screen DOS-based MUMPS platform to an X window workstation and a Microsoft Windows-based workstation. There are differences between these various platforms that impact on software design and on software development strategy. Data structures and conventions were used to isolate hardware, operating system, imaging software, and user-interface differences between platforms in the implementation of functionality for text and image display and interaction. The use of an object-oriented approach greatly increased system portability.

VA's Integrated Imaging System on three platforms.

PubMed Central

Dayhoff, R. E.; Maloney, D. L.; Majurski, W. J.

1992-01-01

The DHCP Integrated Imaging System provides users with integrated patient data including text, image and graphics data. This system has been transferred from its original two screen DOS-based MUMPS platform to an X window workstation and a Microsoft Windows-based workstation. There are differences between these various platforms that impact on software design and on software development strategy. Data structures and conventions were used to isolate hardware, operating system, imaging software, and user-interface differences between platforms in the implementation of functionality for text and image display and interaction. The use of an object-oriented approach greatly increased system portability. PMID:1482983

Electron beam transport analysis of W-band sheet beam klystron

NASA Astrophysics Data System (ADS)

Wang, Jian-Xun; Barnett, Larry R.; Luhmann, Neville C.; Shin, Young-Min; Humphries, Stanley

2010-04-01

The formation and transport of high-current density electron beams are of critical importance for the success of a number of millimeter wave and terahertz vacuum devices. To elucidate design issues and constraints, the electron gun and periodically cusped magnet stack of the original Stanford Linear Accelerator Center designed W-band sheet beam klystron circuit, which exhibited poor beam transmission (≤55%), have been carefully investigated through theoretical and numerical analyses taking advantage of three-dimensional particle tracking solvers. The re-designed transport system is predicted to exhibit 99.76% (cold) and 97.38% (thermal) beam transmission, respectively, under space-charge-limited emission simulations. The optimized design produces the required high aspect ratio (10:1) sheet beam with 3.2 A emission current with highly stable propagation. In the completely redesigned model containing all the circuit elements, more than 99% beam transmission is experimentally observed at the collector located about 160 mm distant from the cathode surface. Results are in agreement of the predictions of two ray-tracing simulators, CST PARTICLE STUDIO and OMNITRAK which also predict the observed poor transmission in the original design. The quantitative analysis presents practical factors in the modeling process to design a magnetic lens structure to stably transport the elliptical beam along the long drift tube.

Titan I propulsion system modeling and possible performance improvements

NASA Astrophysics Data System (ADS)

Giusti, Oreste

This thesis features the Titan I propulsion systems and offers data-supported suggestions for improvements to increase performance. The original propulsion systems were modeled both graphically in CAD and via equations. Due to the limited availability of published information, it was necessary to create a more detailed, secondary set of models. Various engineering equations---pertinent to rocket engine design---were implemented in order to generate the desired extra detail. This study describes how these new models were then imported into the ESI CFD Suite. Various parameters are applied to these imported models as inputs that include, for example, bi-propellant combinations, pressure, temperatures, and mass flow rates. The results were then processed with ESI VIEW, which is visualization software. The output files were analyzed for forces in the nozzle, and various results were generated, including sea level thrust and ISP. Experimental data are provided to compare the original engine configuration models to the derivative suggested improvement models.

Position of the station Borowiec in the Doppler observation campaign WEDOC 80

NASA Astrophysics Data System (ADS)

Pachelski, W.

The position of the Doppler antenna located at the Borowiec Observatory, Poland, is analyzed based on data gathered during the WEDOC 80 study and an earlier study in 1977. Among other findings, it is determined that biases of the reference system origin can be partially eliminated by transforming absolute coordinates of two or more stations into station-to-station vector components, and by determining the vector length while the system scale remains affected by broadcast ephemerides. The standard deviations of absolute coordinates are shown to represent only the internal accuracy of the solution, and are found to depend on the geometrical configuration between the station position and the satellite passes. It is shown that significant correlations between station coordinates in translocation or multilocation are due to the poor conditioning of design matrices with respect to the origin and orientation of the reference system.

The James Webb Space Telescope: Extending the Science

NASA Technical Reports Server (NTRS)

Gardner, Jonathan P.

2012-01-01

The science objectives of the James Webb Space Telescope fall into four themes. The End of the Dark Ages: First Light and Reionization theme seeks to identify the first luminous sources to form and to determine the ionization history of the universe. The Assembly of Galaxies theme seeks to determine how galaxies and the dark matter, gas, stars, metals, morphological structures, and black holes within them evolved from the epoch of reionization to the present. The Birth of Stars and Protoplanetary Systems theme seeks to unravel the birth and early evolution of stars, from infall onto dust-enshrouded protostars, to the genesis of planetary systems. The Planetary Systems and the Origins of Life theme seeks. to determine the physical and chemical properties of planetary systems around nearby stars and of our own, and to investigate the potential for life in those systems. These four science themes were used to establish the design requirements for the observatory and instrumentation. Since Webb's capabilities are unique, those science themes will remain relevant through launch and operations and goals contained within these themes will continue to guide the design and implementation choices for the mission. More recently, it has also become clear that Webb will make major contributions to other areas of research, including dark energy, dark matter, exoplanet characterization and Solar System objects. In this paper, I review the original four science themes and discuss how the scientific output of Webb will extend to these new areas of research.

Three tenets for secure cyber-physical system design and assessment

NASA Astrophysics Data System (ADS)

Hughes, Jeff; Cybenko, George

2014-06-01

This paper presents a threat-driven quantitative mathematical framework for secure cyber-physical system design and assessment. Called The Three Tenets, this originally empirical approach has been used by the US Air Force Research Laboratory (AFRL) for secure system research and development. The Tenets were first documented in 2005 as a teachable methodology. The Tenets are motivated by a system threat model that itself consists of three elements which must exist for successful attacks to occur: - system susceptibility; - threat accessibility and; - threat capability. The Three Tenets arise naturally by countering each threat element individually. Specifically, the tenets are: Tenet 1: Focus on What's Critical - systems should include only essential functions (to reduce susceptibility); Tenet 2: Move Key Assets Out-of-Band - make mission essential elements and security controls difficult for attackers to reach logically and physically (to reduce accessibility); Tenet 3: Detect, React, Adapt - confound the attacker by implementing sensing system elements with dynamic response technologies (to counteract the attackers' capabilities). As a design methodology, the Tenets mitigate reverse engineering and subsequent attacks on complex systems. Quantified by a Bayesian analysis and further justified by analytic properties of attack graph models, the Tenets suggest concrete cyber security metrics for system assessment.

Multi-man flight simulator

NASA Technical Reports Server (NTRS)

Macdonald, G.

1983-01-01

A prototype Air Traffic Control facility and multiman flight simulator facility was designed and one of the component simulators fabricated as a proof of concept. The facility was designed to provide a number of independent simple simulator cabs that would have the capability of some local, stand alone processing that would in turn interface with a larger host computer. The system can accommodate up to eight flight simulators (commercially available instrument trainers) which could be operated stand alone if no graphics were required or could operate in a common simulated airspace if connected to the host computer. A proposed addition to the original design is the capability of inputing pilot inputs and quantities displayed on the flight and navigation instruments to the microcomputer when the simulator operates in the stand alone mode to allow independent use of these commercially available instrument trainers for research. The conceptual design of the system and progress made to date on its implementation are described.

A Circuit-Based Quantum Algorithm Driven by Transverse Fields for Grover's Problem

NASA Technical Reports Server (NTRS)

Jiang, Zhang; Rieffel, Eleanor G.; Wang, Zhihui

2017-01-01

We designed a quantum search algorithm, giving the same quadratic speedup achieved by Grover's original algorithm; we replace Grover's diffusion operator (hard to implement) with a product diffusion operator generated by transverse fields (easy to implement). In our algorithm, the problem Hamiltonian (oracle) and the transverse fields are applied to the system alternatively. We construct such a sequence that the corresponding unitary generates a closed transition between the initial state (even superposition of all states) and a modified target state, which has a high degree of overlap with the original target state.

Cargo Movement Operations System (CMOS). Draft Software Design Document for the PC UNIX Prototype (Navy Configuration), Increment III.

DTIC Science & Technology

1991-04-21

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ ] CLOSED ( ] ORIGINATOR CONTROL NUMBER: SDDN-0003 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: C006-02 DATE: 04/21/91 ORIGINATOR NAME: Ronald J. Lacour OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 272-2999 SUBSTANTIVE: X EDITORIAL: PAGE NUMBER: CUBA0065-1 PARA NUMBER: N/A COMMENT OR RECOMMENDED CHANGE: Change CUVA0065 in Table 6 to CUBA0065 to match the name in Attachment 1. RATIONALE: It appears that this CSU was improperly named in Table 6. CMOS PMO ACCEPTS COMMENT:

Cargo Movement Operations System (CMOS). Final Software Design Document for the Applications CSCI, Increment II

DTIC Science & Technology

1991-10-03

NO [ ] COMMENT DISPOSITION: COMMENT STATUS: OPEN [ CLOSED [] ORIGINATOR CONTROL NUMBER: SDDl-0002 PROGRAM OFFiCE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: A006-0250L DATE: 10/03/11 ORIGINATOR NAME: Ronald J. Lacour OFFICE SYMBOL: SAIC TELEPHONE NUMBER: 272-2999 SUBSTANTIVE: X EDITORIAL: PAGE NUMBER: CU2A5040-19 PARA NUMBER: N/A COMMENT OR RECOMMENDED CHANGE: Add "STANDBY PAX" on the last page of this screen. RATIONALE: This redesigned page is for handling standby passengers. However, no mention of that is present.

Integrating MBSE into Ongoing Projects: Requirements Validation and Test Planning for the ISS SAFER

NASA Technical Reports Server (NTRS)

Anderson, Herbert A.; Williams, Antony; Pierce, Gregory

2016-01-01

The International Space Station (ISS) Simplified Aid for Extra Vehicular Activity (EVA) Rescue (SAFER) is the spacewalking astronaut's final safety measure against separating from the ISS and being unable to return safely. Since the late 1990s, the SAFER has been a standard element of the spacewalking astronaut's equipment. The ISS SAFER project was chartered to develop a new block of SAFER units using a highly similar design to the legacy SAFER (known as the USA SAFER). An on-orbit test module was also included in the project to enable periodic maintenance/propulsion system checkout on the ISS SAFER. On the ISS SAFER project, model-based systems engineering (MBSE) was not the initial systems engineering (SE) approach, given the volume of heritage systems engineering and integration (SE&I) products. The initial emphasis was ensuring traceability to ISS program standards as well as to legacy USA SAFER requirements. The requirements management capabilities of the Cradle systems engineering tool were to be utilized to that end. During development, however, MBSE approaches were applied selectively to address specific challenges in requirements validation and test and verification (T&V) planning, which provided measurable efficiencies to the project. From an MBSE perspective, ISS SAFER development presented a challenge and an opportunity. Addressing the challenge first, the project was tasked to use the original USA SAFER operational and design requirements baseline, with a number of additional ISS program requirements to address evolving certification expectations for systems operating on the ISS. Additionally, a need to redesign the ISS SAFER avionics architecture resulted in a set of changes to the design requirements baseline. Finally, the project added an entirely new functionality for on-orbit maintenance. After initial requirements integration, the system requirements count was approaching 1000, which represented a growth of 4x over the original USA SAFER system. This presented the challenge - How to confirm that this new set of requirements set would result in the creation of the desired capability.

Freeze-drying of nanosuspensions, 1: freezing rate versus formulation design as critical factors to preserve the original particle size distribution.

PubMed

Beirowski, Jakob; Inghelbrecht, Sabine; Arien, Albertina; Gieseler, Henning

2011-05-01

It has been recently reported in the literature that using a fast freezing rate during freeze-drying of drug nanosuspensions is beneficial to preserve the original particle size distribution. All freezing rates studied were obtained by utilizing a custom-made apparatus and were then indirectly related to conventional vial freeze-drying. However, a standard freeze-dryer is only capable of achieving moderate freezing rates in the shelf fluid circulation system. Therefore, it was the purpose of the present study to evaluate the possibility to establish a typical freezing protocol applicable to a standard freeze-drying unit in combination with an adequate choice of cryoprotective excipients and steric stabilizers to preserve the original particle size distribution. Six different drug nanosuspensions containing itraconazole as a drug model were studied using freeze-thaw experiments and a full factorial design to reveal major factors for the stabilization of drug nanosuspensions and the corresponding interactions. In contrast to previous reports, the freezing regime showed no significant influence on preserving the original particle size distribution, suggesting that the concentrations of both the steric stabilizer and the cryoprotective agent are optimized. Moreover, it could be pinpointed that the combined effect of steric stabilizer and cryoprotectant clearly contribute to nanoparticle stability. Copyright © 2010 Wiley-Liss, Inc.

Electro-Mechanical Actuator. DC Resonant Link Controller

NASA Technical Reports Server (NTRS)

Schreiner, Kenneth E.

1996-01-01

This report summarizes the work performed on the 68 HP electro-mechanical actuator (EMA) system developed on NASA contract for the Electrical Actuation (ELA) Technology Bridging Program. The system was designed to demonstrate the capability of large, high power linear ELAs for applications such as Thrust Vector Control (TVC) on rocket engines. It consists of a motor controller, drive electronics and a linear actuator capable of up to 32,00 lbs loading at 7.4 inches/second. The drive electronics are based on the Resonant DC link concept and operate at a nominal frequency of 55 kHz. The induction motor is a specially designed high speed, low inertia motor capable of a 68 peak HP. The actuator was originally designed by MOOG Aerospace under an internal R & D program to meet Space Shuttle Main Engine (SSME) TVC requirements. The design was modified to meet this programs linear rate specification of 7.4 inches/second. The motor and driver were tested on a dynamometer at the Martin Marietta Space Systems facility. System frequency response, step response and force-velocity tests were conducted at the MOOG Aerospace facility. A complete description of the system and all test results can be found in the body of the report.

Modified ACES Portable Life Support Integration, Design, and Testing for Exploration Missions

NASA Technical Reports Server (NTRS)

Kelly, Cody

2014-01-01

NASA's next generation of exploration missions provide a unique challenge to designers of EVA life support equipment, especially in a fiscally-constrained environment. In order to take the next steps of manned space exploration, NASA is currently evaluating the use of the Modified ACES (MACES) suit in conjunction with the Advanced Portable Life Support System (PLSS) currently under development. This paper will detail the analysis and integration of the PLSS thermal and ventilation subsystems into the MACES pressure garment, design of prototype hardware, and hardware-in-the-loop testing during the spring 2014 timeframe. Prototype hardware was designed with a minimal impact philosophy in order to mitigate design constraints becoming levied on either the advanced PLSS or MACES subsystems. Among challenges faced by engineers were incorporation of life support thermal water systems into the pressure garment cavity, operational concept definition between vehicle/portable life support system hardware, and structural attachment mechanisms while still enabling maximum EVA efficiency from a crew member's perspective. Analysis was completed in late summer 2013 to 'bound' hardware development, with iterative analysis cycles throughout the hardware development process. The design effort will cumulate in the first ever manned integration of NASA's advanced PLSS system with a pressure garment originally intended primarily for use in a contingency survival scenario.

Design of a lunar transportation system, volume 2

NASA Technical Reports Server (NTRS)

1990-01-01

The Spring 1990 Introduction to Design class was asked to conceptually design second generation lunar vehicles and equipment as a semester design project. A brief summary of four of the final projects, is presented. The designs were to facilitate the transportation of personnel and materials. The eight topics to choose from included flying vehicles, ground based vehicles, robotic arms, and life support systems. A lunar flying vehicle that uses clean propellants for propulsion is examined. A design that will not contribute to the considerable amount of caustic pollution already present in the sparse lunar atmosphere is addressed by way of ballistic flight techniques. A second generation redesign of the current Extra Vehicular Activity (EVA) suit to increase operating time, safety, and efficiency is also addressed. A separate life support system is also designed to be permanently attached to the lunar rover. The two systems would interact through the use of an umbilical cord connection. A ground based vehicle which will travel for greater distances than a 37.5 kilometer radius from a base on the lunar surface was designed. The vehicle is pressurized due to the fact that existing lunar rovers are limited by the EVA suits currently in use. A robotic arm for use at lunar bases or on roving vehicles on the lunar surface was designed. The arm was originally designed as a specimen gathering device, but it can be used for a wide range of tasks through the use of various attachments.

Integration of uniform design and quantum-behaved particle swarm optimization to the robust design for a railway vehicle suspension system under different wheel conicities and wheel rolling radii

NASA Astrophysics Data System (ADS)

Cheng, Yung-Chang; Lee, Cheng-Kang

2017-10-01

This paper proposes a systematic method, integrating the uniform design (UD) of experiments and quantum-behaved particle swarm optimization (QPSO), to solve the problem of a robust design for a railway vehicle suspension system. Based on the new nonlinear creep model derived from combining Hertz contact theory, Kalker's linear theory and a heuristic nonlinear creep model, the modeling and dynamic analysis of a 24 degree-of-freedom railway vehicle system were investigated. The Lyapunov indirect method was used to examine the effects of suspension parameters, wheel conicities and wheel rolling radii on critical hunting speeds. Generally, the critical hunting speeds of a vehicle system resulting from worn wheels with different wheel rolling radii are lower than those of a vehicle system having original wheels without different wheel rolling radii. Because of worn wheels, the critical hunting speed of a running railway vehicle substantially declines over the long term. For safety reasons, it is necessary to design the suspension system parameters to increase the robustness of the system and decrease the sensitive of wheel noises. By applying UD and QPSO, the nominal-the-best signal-to-noise ratio of the system was increased from -48.17 to -34.05 dB. The rate of improvement was 29.31%. This study has demonstrated that the integration of UD and QPSO can successfully reveal the optimal solution of suspension parameters for solving the robust design problem of a railway vehicle suspension system.

Calculation of energy costs of composite biomass stirring at biogas stations

NASA Astrophysics Data System (ADS)

Suslov, D. Yu; Temnikov, D. O.

2018-03-01

The paper is devoted to the study of the equipment to produce biogas fuel from organic wastes. The bioreactor equipped with a combined stirring system ensuring mechanical and bubbling stirring is designed. The method of energy cost calculation of the combined stirring system with original design is suggested. The received expressions were used in the calculation of the stirring system installed in the 10 m3 bioreactor: power consumed by the mixer during the start-up period made Nz =9.03 kW, operating power of the mixer made NE =1.406 kW, compressor power for bubbling stirring made NC =18.5 kW. Taking into account the operating mode of single elements of the stirring system, the energy cost made 4.38% of the total energy received by the biogas station.

Integral habitat transport system

NASA Technical Reports Server (NTRS)

Elliott, Bill; Frazer, Scott; Higgs, Joey; Huff, Jason; Milam, Tigree

1994-01-01

In the 1993 Fall quarter, the ME 4182 design class was sponsored to study various scenarios that needed to be studied for Martian travel. The class was sponsored by NASA and there were several different design projects. The design that group three chose was an integral transport system for a Martian habitat. An integral transport system means the design had to be one that was attached to the habitat. There were several criteria that the design had to meet. Group three performed an in depth study of the Martian environment and looked at several different design ideas. The concept group three developed involved the use of kinematic linkages and the use of Martian gravity to move the habitat. The various design concepts, the criteria matrices and all other aspects that helped group three develop their design can be found in their 1993 ME 4182 design report. Now it is Winter quarter 1994 and group three is faced with another problem. The problem is building a working prototype of their Fall design. The limitations this quarter were the parts. The group had to make the prototype work with existing manufactured parts or make the parts themselves in a machine shop. The prototype was scaled down roughly about twelve times smaller than the original design. The following report describes the actions taken by group three to build a working model.

A general U-block model-based design procedure for nonlinear polynomial control systems

NASA Astrophysics Data System (ADS)

Zhu, Q. M.; Zhao, D. Y.; Zhang, Jianhua

2016-10-01

The proposition of U-model concept (in terms of 'providing concise and applicable solutions for complex problems') and a corresponding basic U-control design algorithm was originated in the first author's PhD thesis. The term of U-model appeared (not rigorously defined) for the first time in the first author's other journal paper, which established a framework for using linear polynomial control system design approaches to design nonlinear polynomial control systems (in brief, linear polynomial approaches → nonlinear polynomial plants). This paper represents the next milestone work - using linear state-space approaches to design nonlinear polynomial control systems (in brief, linear state-space approaches → nonlinear polynomial plants). The overall aim of the study is to establish a framework, defined as the U-block model, which provides a generic prototype for using linear state-space-based approaches to design the control systems with smooth nonlinear plants/processes described by polynomial models. For analysing the feasibility and effectiveness, sliding mode control design approach is selected as an exemplary case study. Numerical simulation studies provide a user-friendly step-by-step procedure for the readers/users with interest in their ad hoc applications. In formality, this is the first paper to present the U-model-oriented control system design in a formal way and to study the associated properties and theorems. The previous publications, in the main, have been algorithm-based studies and simulation demonstrations. In some sense, this paper can be treated as a landmark for the U-model-based research from intuitive/heuristic stage to rigour/formal/comprehensive studies.

Thermal storage system flops at Illinois State office building

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ponczak, G.

1986-02-03

A thermal storage and electric resistive heating system in the new State of Illinois building in Chicago has used about 65% more electricity in its first year of operation than building designers originally predicted, according to state government sources. The state proposes to spend about $2 million to fine tune the system this year. Total first year electricity usage for the all-electric, 1.15 million square foot building was expected to be 18.7 million kilowatt hours (kWh). But according to recent energy bills, actual usage for the first year of operation, ending in December, was 31 million kWh, a usage overrunmore » that has cost the state of Illinois an extra $500,000. Some industry sources blame the thermal storage system and the electric heat system, which were untried when proposed in 1980, for much of the overrun, while others blame the building design.« less

Gas-Purged Headspace Liquid Phase Microextraction System for Determination of Volatile and Semivolatile Analytes

PubMed Central

Zhang, Meihua; Bi, Jinhu; Yang, Cui; Li, Donghao; Piao, Xiangfan

2012-01-01

In order to achieve rapid, automatic, and efficient extraction for trace chemicals from samples, a system of gas-purged headspace liquid phase microextraction (GP-HS-LPME) has been researched and developed based on the original HS-LPME technique. In this system, semiconductor condenser and heater, whose refrigerating and heating temperatures were controlled by microcontroller, were designed to cool the extraction solvent and to heat the sample, respectively. Besides, inert gas, whose gas flow rate was adjusted by mass flow controller, was continuously introduced into and discharged from the system. Under optimized parameters, extraction experiments were performed, respectively, using GP-HS-LPME system and original HS-LPME technique for enriching volatile and semivolatile target compounds from the same kind of sample of 15 PAHs standard mixture. GC-MS analysis results for the two experiments indicated that a higher enrichment factor was obtained from GP-HS-LPME. The enrichment results demonstrate that GP-HS-LPME system is potential in determination of volatile and semivolatile analytes from various kinds of samples. PMID:22448341

The road surveying system of the federal highway research institute - a performance evaluation of road segmentation algorithms

NASA Astrophysics Data System (ADS)

Streiter, R.; Wanielik, G.

2013-07-01

The construction of highways and federal roadways is subject to many restrictions and designing rules. The focus is on safety, comfort and smooth driving. Unfortunately, the planning information for roadways and their real constitution, course and their number of lanes and lane widths is often unsure or not available. Due to digital map databases of roads raised much interest during the last years and became one major cornerstone of innovative Advanced Driving Assistance Systems (ADASs), the demand for accurate and detailed road information increases considerably. Within this project a measurement system for collecting high accurate road data was developed. This paper gives an overview about the sensor configuration within the measurement vehicle, introduces the implemented algorithms and shows some applications implemented in the post processing platform. The aim is to recover the origin parametric description of the roadway and the performance of the measurement system is being evaluated against several original road construction information.

Continuous monitoring of the lunar or Martian subsurface using on-board pattern recognition and neural processing of Rover geophysical data

NASA Technical Reports Server (NTRS)

Mcgill, J. W.; Glass, C. E.; Sternberg, B. K.

1990-01-01

The ultimate goal is to create an extraterrestrial unmanned system for subsurface mapping and exploration. Neural networks are to be used to recognize anomalies in the profiles that correspond to potentially exploitable subsurface features. The ground penetrating radar (GPR) techniques are likewise identical. Hence, the preliminary research focus on GPR systems will be directly applicable to seismic systems once such systems can be designed for continuous operation. The original GPR profile may be very complex due to electrical behavior of the background, targets, and antennas, much as the seismic record is made complex by multiple reflections, ghosting, and ringing. Because the format of the GPR data is similar to the format of seismic data, seismic processing software may be applied to GPR data to help enhance the data. A neural network may then be trained to more accurately identify anomalies from the processed record than from the original record.

cOSPREY: A Cloud-Based Distributed Algorithm for Large-Scale Computational Protein Design

PubMed Central

Pan, Yuchao; Dong, Yuxi; Zhou, Jingtian; Hallen, Mark; Donald, Bruce R.; Xu, Wei

2016-01-01

Abstract Finding the global minimum energy conformation (GMEC) of a huge combinatorial search space is the key challenge in computational protein design (CPD) problems. Traditional algorithms lack a scalable and efficient distributed design scheme, preventing researchers from taking full advantage of current cloud infrastructures. We design cloud OSPREY (cOSPREY), an extension to a widely used protein design software OSPREY, to allow the original design framework to scale to the commercial cloud infrastructures. We propose several novel designs to integrate both algorithm and system optimizations, such as GMEC-specific pruning, state search partitioning, asynchronous algorithm state sharing, and fault tolerance. We evaluate cOSPREY on three different cloud platforms using different technologies and show that it can solve a number of large-scale protein design problems that have not been possible with previous approaches. PMID:27154509

A fast direct solver for boundary value problems on locally perturbed geometries

NASA Astrophysics Data System (ADS)

Zhang, Yabin; Gillman, Adrianna

2018-03-01

Many applications including optimal design and adaptive discretization techniques involve solving several boundary value problems on geometries that are local perturbations of an original geometry. This manuscript presents a fast direct solver for boundary value problems that are recast as boundary integral equations. The idea is to write the discretized boundary integral equation on a new geometry as a low rank update to the discretized problem on the original geometry. Using the Sherman-Morrison formula, the inverse can be expressed in terms of the inverse of the original system applied to the low rank factors and the right hand side. Numerical results illustrate for problems where perturbation is localized the fast direct solver is three times faster than building a new solver from scratch.

Accelerating Families of Fuzzy K-Means Algorithms for Vector Quantization Codebook Design

PubMed Central

Mata, Edson; Bandeira, Silvio; de Mattos Neto, Paulo; Lopes, Waslon; Madeiro, Francisco

2016-01-01

The performance of signal processing systems based on vector quantization depends on codebook design. In the image compression scenario, the quality of the reconstructed images depends on the codebooks used. In this paper, alternatives are proposed for accelerating families of fuzzy K-means algorithms for codebook design. The acceleration is obtained by reducing the number of iterations of the algorithms and applying efficient nearest neighbor search techniques. Simulation results concerning image vector quantization have shown that the acceleration obtained so far does not decrease the quality of the reconstructed images. Codebook design time savings up to about 40% are obtained by the accelerated versions with respect to the original versions of the algorithms. PMID:27886061

Accelerating Families of Fuzzy K-Means Algorithms for Vector Quantization Codebook Design.

PubMed

Mata, Edson; Bandeira, Silvio; de Mattos Neto, Paulo; Lopes, Waslon; Madeiro, Francisco

2016-11-23

The performance of signal processing systems based on vector quantization depends on codebook design. In the image compression scenario, the quality of the reconstructed images depends on the codebooks used. In this paper, alternatives are proposed for accelerating families of fuzzy K-means algorithms for codebook design. The acceleration is obtained by reducing the number of iterations of the algorithms and applying efficient nearest neighbor search techniques. Simulation results concerning image vector quantization have shown that the acceleration obtained so far does not decrease the quality of the reconstructed images. Codebook design time savings up to about 40% are obtained by the accelerated versions with respect to the original versions of the algorithms.

78 FR 11593 - Environmental Impact and Related Procedures

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-19

... reconstruction activity is in the same location with the same capacity, dimensions, and design as the original... capacity, dimensions, and design as the original road, highway, or bridge as before the declaration, and (B... and design changes to a damaged facility to meet current design standards; (2) repair and...

Colloidal chirality in wormlike micellar systems exclusively originated from achiral species: Role of secondary assembly and stimulus responsivity.

PubMed

Zhao, Wenrong; Hao, Jingcheng

2016-09-15

Colloidal chirality in wormlike micellar systems exclusively originated from achiral species and discussion of the role of secondary assembly of fiber-like aggregates in chirality generation were presented in this paper. Herein, formation of colloidal wormlike micelles for the first time incorporated chirality and redox-responsiveness into one design via noncovalent interaction. A dual-stimuli-responsive gel of wormlike micelles which were designed by employing a dual-responsive cationic surfactant (FTMA) and a strong gelator (AzoNa4) and regulated by redox reaction and host-guest inclusion is presented. Both the redox and host-guest interaction play an important role in regulating the viscosity and supramolecular chirality of gels of the wormlike micelles. The supramolecular chirality and viscosity of the wormlike micelle gels were switched reversibly by exerting chemical redox onto the ferrocenyl groups. For the amphiphile FTMA containing redox-active ferrocenyl group, reversible control of the oxidation state of ferrocenyl groups leads to the charge and hydrophobicity changes of FTMA, therefore change its self-assembly behavior. Of equal interest, β-CD successfully detached the wormlike micelles via the recognition-inclusion behavior with FTMA and invalidate the H-bond and hydrophobic interaction between FTMA and AzoH4. This designed system provides a new strategy to tune the supramolecular chirality of colloidal aggregates and explore the specific packing mode detail within the micelles or the secondary assembly of the inter-micelles. We anticipate this dual-responsive H-bond-directed chiral gel switch could propose a new strategy when researchers designing new, multi-responsive functional gel materials. Copyright © 2016 Elsevier Inc. All rights reserved.

Validation of General Electric Aviation DAPS2015 Digital Recording and 1/3 Octave Analysis System for Use in Support of Aircraft Noise Certification Efforts in Compliance with 14 CFR Part 36; Letter Report: V324-FA5JBQ-LR4 Rev. 1

DOT National Transportation Integrated Search

2017-10-31

NOTE: This is a revision of Letter Report V324-FA5JBQ-LR4. The purpose of the revision is to correctly identify the system designation for which the validation applies. The applicant originally identified the materials provided in support of this val...

Knowledge-Based Vision Techniques for the Autonomous Land Vehicle Program

DTIC Science & Technology

1991-10-01

Knowledge System The CKS is an object-oriented knowledge database that was originally designed to serve as the central information manager for a...34 Representation Space: An Approach to the Integra- tion of Visual Information ," Proc. of DARPA Image Understanding Workshop, Palo Alto, CA, pp. 263-272, May 1989...Strat, " Information Management in a Sensor-Based Au- tonomous System," Proc. DARPA Image Understanding Workshop, University of Southern CA, Vol.1, pp

A Human-Automation Interface Model to Guide Automation Design of System Functions: A Way to Achieve Manning Goals in New Systems

DTIC Science & Technology

2005-12-01

60 x THIS PAGE INTENTIONALLY LEFT BLANK xi LIST OF TABLES Table 1...anywhere from one minute to several hours, depending on the needs of the analyst. The models generated for this thesis were set to run for 60 ...of a workload threshold goes back to the original LHX analysis from McCracken and Aldrich (1984). The IMPRINT 59 workload value of 60 has been

Long-Term Durability Test for the Left Ventricular Assist System EVAHEART under the Physiologic Pulsatile Load.

PubMed

Kitano, Tomoya; Iwasaki, Kiyotaka

The EVAHEART Left Ventricular Assist System (LVAS) was designed for the long-term support of a patient with severe heart failure. It has an original water lubrication system for seal and bearing and wear on these parts was considered one of its critical failure modes. A durability test focusing on wear was designed herein. We developed a mock loop, which generates a physiologic pulsatile flow and is sufficiently durable for a long-term test. The pulsatile load and the low fluid viscosity enable the creation of a severe condition for the mechanical seal. A total of 18 EVAHEART blood pumps completed 2 years of operation under the pulsatile condition without any failure. It indicated the EVAHEART blood pump had a greater than 90% reliability with a 88% confidence level. The test was continued with six blood pumps and achieved an average of 8.6 years, which was longer than the longest clinical use in Japan. The test result showed that no catastrophic, critical, marginal, or minor failures of the blood pump or their symptoms were observed. The seal performance was maintained after the test. Moreover, the surface roughness did not change, which showed any burn or abnormal wear occurred. The original water lubrication system equipped in EVAHEART LVAS prevent severe wear on the seal and the bearing, and it can be used in the bridge to transplant and destination therapy.

Algorithm design of liquid lens inspection system

NASA Astrophysics Data System (ADS)

Hsieh, Lu-Lin; Wang, Chun-Chieh

2008-08-01

In mobile lens domain, the glass lens is often to be applied in high-resolution requirement situation; but the glass zoom lens needs to be collocated with movable machinery and voice-coil motor, which usually arises some space limits in minimum design. In high level molding component technology development, the appearance of liquid lens has become the focus of mobile phone and digital camera companies. The liquid lens sets with solid optical lens and driving circuit has replaced the original components. As a result, the volume requirement is decreased to merely 50% of the original design. Besides, with the high focus adjusting speed, low energy requirement, high durability, and low-cost manufacturing process, the liquid lens shows advantages in the competitive market. In the past, authors only need to inspect the scrape defect made by external force for the glass lens. As to the liquid lens, authors need to inspect the state of four different structural layers due to the different design and structure. In this paper, authors apply machine vision and digital image processing technology to administer inspections in the particular layer according to the needs of users. According to our experiment results, the algorithm proposed can automatically delete non-focus background, extract the region of interest, find out and analyze the defects efficiently in the particular layer. In the future, authors will combine the algorithm of the system with automatic-focus technology to implement the inside inspection based on the product inspective demands.

Development of a non-piston MR suspension rod for variable mass systems

NASA Astrophysics Data System (ADS)

Deng, Huaxia; Han, Guanghui; Zhang, Jin; Wang, Mingxian; Ma, Mengchao; Zhong, Xiang; Yu, Liandong

2018-06-01

The semi-active suspension systems for variable mass systems require long work stroke and variable damping, while the currently piston structure limits the work stroke for the magnetorheological (MR) dampers. The main work of this paper is to design a semi-active non-piston MR (NPMR) suspension rod for the reduction of the vibration of an automatic impeller washing machine, which is a typical variable mass system. The designed suspension rod locates in the suspension system that links the internal tub to the washing machine cabinet. The NPMR suspension rod includes a MR part and a air part. The MR part can provide low initial damping force and the unlimited work stroke compared with the piston MR damper. The hysteretic response tests and vibration performance evaluation with different loadings are conducted to verify the dynamic performance for the designed rod. The measured damping force of the MR part varies from 5 to 20 N. Studies of dehydration mode experiments of the washing machine indicate that its vibration acceleration with the NPMR suspension rods can reduce to half of the original passive ones in certain conditions.

A Library of Rad Hard Mixed-Voltage/Mixed-Signal Building Blocks for Integration of Avionics Systems for Deep Space

NASA Technical Reports Server (NTRS)

Mojarradi, M. M.; Blaes, B.; Kolawa, E. A.; Blalock, B. J.; Li, H. W.; Buck, K.; Houge, D.

2001-01-01

To build the sensor intensive system-on-a-chip for the next generation spacecrafts for deep space, Center for Integration of Space Microsystems at JPL (CISM) takes advantage of the lower power rating and inherent radiation resistance of Silicon on Insulator technology (SOI). We are developing a suite of mixed-voltage and mixed-signal building blocks in Honeywell's SOI process that can enable the rapid integration of the next generation avionics systems with lower power rating, higher reliability, longer life, and enhanced radiation tolerance for spacecrafts such as the Europa Orbiter and Europa Lander. The mixed-voltage building blocks are predominantly for design of adaptive power management systems. Their design centers around an LDMOS structure that is being developed by Honeywell, Boeing Corp, and the University of Idaho. The mixed-signal building blocks are designed to meet the low power, extreme radiation requirement of deep space applications. These building blocks are predominantly used to interface analog sensors to the digital CPU of the next generation avionics system on a chip. Additional information is contained in the original extended abstract.

Building a COTS archive for satellite data

NASA Technical Reports Server (NTRS)

Singer, Ken; Terril, Dave; Kelly, Jack; Nichols, Cathy

1994-01-01

The goal of the NOAA/NESDIS Active Archive was to provide a method of access to an online archive of satellite data. The archive had to manage and store the data, let users interrogate the archive, and allow users to retrieve data from the archive. Practical issues of the system design such as implementation time, cost and operational support were examined in addition to the technical issues. There was a fixed window of opportunity to create an operational system, along with budget and staffing constraints. Therefore, the technical solution had to be designed and implemented subject to constraint imposed by the practical issues. The NOAA/NESDIS Active Archive came online in July of 1994, meeting all of its original objectives.

AQUATOOL, a generalized decision-support system for water-resources planning and operational management

NASA Astrophysics Data System (ADS)

Andreu, J.; Capilla, J.; Sanchís, E.

1996-04-01

This paper describes a generic decision-support system (DSS) which was originally designed for the planning stage of dicision-making associated with complex river basins. Subsequently, it was expanded to incorporate modules relating to the operational stage of decision-making. Computer-assisted design modules allow any complex water-resource system to be represented in graphical form, giving access to geographically referenced databases and knowledge bases. The modelling capability includes basin simulation and optimization modules, an aquifer flow modelling module and two modules for risk assessment. The Segura and Tagus river basins have been used as case studies in the development and validation phases. The value of this DSS is demonstrated by the fact that both River Basin Agencies currently use a version for the efficient management of their water resources.

An 8.4-GHz dual-maser front-end system for Parkes reimplementation

NASA Technical Reports Server (NTRS)

Trowbridge, D. L.; Loreman, J. R.; Brunzie, T. J.; Quinn, R.

1990-01-01

An 8.4-GHz front-end system consisting of a feedhorn, a waveguide feed assembly, dual masers, and downconverters was reimplemented at Parkes as part of the Parkes Canberra Telemetry Array for the Voyager Neptune encounter. The front-end system was originally assembled by the European Space Agency and installed on the Parkes antenna for the Giotto project. It was also used on a time-sharing basis by the Deep Space Network as part of the Parkes Canberra Telemetry Array to enhance the data return from the Voyager Uranus encounter. At the conclusion of these projects in 1986, part of the system was then shipped to JPL on loan for reimplementation at Parkes for the Voyager Neptune encounter. New design and implementation required to make the system operable at Parkes included new microwave front-end control cabinets, closed-cycle refrigeration monitor system, noise-adding radiometer system, front-end controller assembly, X81 local oscillator multiplier, and refurbishment of the original dual 8.4-GHz traveling-wave masers and waveguide feed system. The front-end system met all requirements during the encounter and was disassembled in October 1989 and returned to JPL.

4. Photographic copy of original design drawing, dated January 1970 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Photographic copy of original design drawing, dated January 1970 (original Army Operation Drawing in possession of the U.S. Army Corps of Engineers, Huntsville Division) Elevations - Stanley R. Mickelsen Safeguard Complex, Universal Missile Building, Between Tactical Road South & Patrol Road, Nekoma, Cavalier County, ND

John F. Kennedy Space Center's Wireless Hang Angle Instrumentation System

NASA Technical Reports Server (NTRS)

Kohler, Jeff

2009-01-01

The technology is a high-precision, wireless inclinometer. The system was designed for monitoring the suspension angle of the Orbiter vehicle during loading onto the Solid Rocket Boosters of the Space Shuttle. Originally, operators manually measured the alignment of the Orbiter with a hand-held inclinometer on a nonrigid surface. The measurement was open to interpretation by the loader. If the Orbiter is misaligned, it can crush ball joints and delay the loading while repairs are made. With this system, the Orbiter can be loaded without damage and without manual measurement.

Integration of Externally Carried Weapon Systems with Military Helicopters (L’Integration des Systemes d’Armes Transportes en Charge Externe sur les Helicopteres Militaires)

DTIC Science & Technology

1990-04-01

Np - Yaw to Roll Derivative (Yaw/Roll Coupling) Hr - Yaw to Yaw Rate Derivative (Yaw Damping) M - Pitch to Incidence Derivative (Incidence Stability) F...system is installed in the same configuration as used on the land based vehicle, simply by bolting-on to the limited number of available hard points...helicopters not originally designed to take external loads. The limited number of hard points on the fuselage structure leads to define supports of complex

Designing for Change: Interoperability in a scaling and adapting environment

NASA Astrophysics Data System (ADS)

Yarmey, L.

2015-12-01

The Earth Science cyberinfrastructure landscape is constantly changing. Technologies advance and technical implementations are refined or replaced. Data types, volumes, packaging, and use cases evolve. Scientific requirements emerge and mature. Standards shift while systems scale and adapt. In this complex and dynamic environment, interoperability remains a critical component of successful cyberinfrastructure. Through the resource- and priority-driven iterations on systems, interfaces, and content, questions fundamental to stable and useful Earth Science cyberinfrastructure arise. For instance, how are sociotechnical changes planned, tracked, and communicated? How should operational stability balance against 'new and shiny'? How can ongoing maintenance and mitigation of technical debt be managed in an often short-term resource environment? The Arctic Data Explorer is a metadata brokering application developed to enable discovery of international, interdisciplinary Arctic data across distributed repositories. Completely dependent on interoperable third party systems, the Arctic Data Explorer publicly launched in 2013 with an original 3000+ data records from four Arctic repositories. Since then the search has scaled to 25,000+ data records from thirteen repositories at the time of writing. In the final months of original project funding, priorities shift to lean operations with a strategic eye on the future. Here we present lessons learned from four years of Arctic Data Explorer design, development, communication, and maintenance work along with remaining questions and potential directions.

Dynamic analysis methods for detecting anomalies in asynchronously interacting systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Akshat; Solis, John Hector; Matschke, Benjamin

2014-01-01

Detecting modifications to digital system designs, whether malicious or benign, is problematic due to the complexity of the systems being analyzed. Moreover, static analysis techniques and tools can only be used during the initial design and implementation phases to verify safety and liveness properties. It is computationally intractable to guarantee that any previously verified properties still hold after a system, or even a single component, has been produced by a third-party manufacturer. In this paper we explore new approaches for creating a robust system design by investigating highly-structured computational models that simplify verification and analysis. Our approach avoids the needmore » to fully reconstruct the implemented system by incorporating a small verification component that dynamically detects for deviations from the design specification at run-time. The first approach encodes information extracted from the original system design algebraically into a verification component. During run-time this component randomly queries the implementation for trace information and verifies that no design-level properties have been violated. If any deviation is detected then a pre-specified fail-safe or notification behavior is triggered. Our second approach utilizes a partitioning methodology to view liveness and safety properties as a distributed decision task and the implementation as a proposed protocol that solves this task. Thus the problem of verifying safety and liveness properties is translated to that of verifying that the implementation solves the associated decision task. We develop upon results from distributed systems and algebraic topology to construct a learning mechanism for verifying safety and liveness properties from samples of run-time executions.« less

Old Wine in New Skins: The Sensitivity of Established Findings to New Methods

ERIC Educational Resources Information Center

Foster, E. Michael; Wiley-Exley, Elizabeth; Bickman, Leonard

2009-01-01

Findings from an evaluation of a model system for delivering mental health services to youth were reassessed to determine the robustness of key findings to the use of methodologies unavailable to the original analysts. These analyses address a key concern about earlier findings--that the quasi-experimental design involved the comparison of two…

Grouping Students and Pacing Instruction. Learning Package No. 15.

ERIC Educational Resources Information Center

Nelson, Carol; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on grouping students and pacing instruction is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full…

Language Diversity and Reading Instruction. Learning Package No. 21.

ERIC Educational Resources Information Center

Nelson, Carol; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on language diversity and reading instruction is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Observation and Feedback. Learning Package No. 12.

ERIC Educational Resources Information Center

Aiex, Nola Kortner; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on observation and feedback is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Extending the Basal. Learning Package No. 13.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on extending the basal is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Using Skills and Strategies for Effective Learning. Learning Package No. 9.

ERIC Educational Resources Information Center

Hong, Zhang; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on using skills and strategies for effective learning is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the…

Writing Strategies for Gifted Children. Learning Package No. 45.

ERIC Educational Resources Information Center

Hyslop, Nancy; Smith, Carl, Comp.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on writing strategies for gifted children is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Trends and Issues in Reading Education. Learning Package No. 11.

ERIC Educational Resources Information Center

Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on trends and issues in reading education is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full…

The Changing Perspective in Reading Assessment. Learning Package No. 14.

ERIC Educational Resources Information Center

Simic, Marge; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on changing perspective in reading assessment is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the…

Making Writing Public. Learning Package No. 35.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on making writing public is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…

Promoting Language Growth across the Curriculum. Learning Package No. 18.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on language across the curriculum is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of…

Reading Programs for Gifted Readers. Learning Package No. 28.

ERIC Educational Resources Information Center

Collins, Norma, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on reading programs for gifted readers is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Reader Response Theory and Related Instructional Strategies. Learning Package No. 24.

ERIC Educational Resources Information Center

Collins, Norma; Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on reader response theory and related instructional strategies is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on…

Children and the Library. Learning Package No. 41.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on children and the library is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving…

Integrating the Language Arts. Learning Package No. 48.

ERIC Educational Resources Information Center

Chao, Han-Hua, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on integrating the language arts is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture…

Spelling and the Writing Process. Learning Package No. 36.

ERIC Educational Resources Information Center

Simic, Marge, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on spelling and the writing process is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture…

Strategic Thinking through Writing. Learning Package No. 37.

ERIC Educational Resources Information Center

Hong, Zhang, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on strategic thinking through writing is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Using Folk Literature. Learning Package No. 3.

ERIC Educational Resources Information Center

Smith, Carl, Comp.

Originally developed for the Department of Defense Schools (DoDDS) system, this learning package on using folk literature is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes a comprehensive search of the ERIC database; a lecture giving an overview on the topic; the full text of several…

Developing Listening and Speaking Skills. Learning Package No. 46.

ERIC Educational Resources Information Center

Hyslop, Nancy, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on developing listening and speaking skills is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a…

Appreciation of Literature. Learning Package No. 49.

ERIC Educational Resources Information Center

Kelly, Dawn, Comp.; Smith, Carl, Ed.

Originally developed as part of a project for the Department of Defense Schools (DoDDS) system, this learning package on appreciating literature is designed for teachers who wish to upgrade or expand their teaching skills on their own. The package includes an overview of the project; a comprehensive search of the ERIC database; a lecture giving an…