ASTP fluid transfer measurement experiment. [using breadboard model

NASA Technical Reports Server (NTRS)

Fogal, G. L.

1974-01-01

The ASTP fluid transfer measurement experiment flight system design concept was verified by the demonstration and test of a breadboard model. In addition to the breadboard effort, a conceptual design of the corresponding flight system was generated and a full scale mockup fabricated. A preliminary CEI specification for the flight system was also prepared.

Introduction of Cooperative Vehicle-to-Infrastructure Systems to Improve Speed Harmonization

DOT National Transportation Integrated Search

2016-03-01

This project executed a preliminary experiment of vehicle-to-infrastructure (V2I)-based speed harmonization in which speed guidance was communicated directly to vehicles. This experiment involved a set of micro-simulation experiments and a limited nu...

Preliminary design of the Space Station internal thermal control system

NASA Technical Reports Server (NTRS)

Herrin, Mark T.; Patterson, David W.; Turner, Larry D.

1987-01-01

The baseline preliminary design configuration of the Internal Thermal Control system (ITCS) of the U.S. Space Station pressurized elements (i.e., the Habitation and U.S. Laboratory modules, pressurized logistics carrier, and resources nodes) is defined. The ITCS is composed of both active and passive components. The subsystems which comprise the ITCS are identified and their functional descriptions are provided. The significant trades and analyses, which were performed during Phase B (i.e., the preliminary design phase) that resulted in the design described herein, are discussed. The ITCS interfaces with the station's central Heat Rejection and Transport System (HRTS), other systems, and externally attached pressurized payloads are described. Requirements on the ITCS with regard to redundancy and experiment support are also addressed.

Modular space station phase B extension preliminary system design. Volume 3: Experiment analyses

NASA Technical Reports Server (NTRS)

Wengrow, G. L.; Lillenas, A. N.

1972-01-01

Experiment analysis tasks performed during program definition study are described. Experiment accommodation and scheduling, and defining and implementing the laboratory evolution are discussed. The general purpose laboratory requirements and concepts are defined, and supplemental studies are reported.

Systems engineering and the user: Incorporation of user requirements into the SE process

NASA Technical Reports Server (NTRS)

Naugle, John E.

1993-01-01

This paper is organized into four parts. In the Gestation Phase, I describe the process of starting a new mission and establishing its rough boundaries. Next I show how the scientific experiments are selected. Then we enter the Preliminary Design Phase, where we incorporate the scientist's instruments into the systems engineering process. Finally, I show how the Preliminary Design Review (PDR) assures NASA management and the scientists that the scientific requirements have been incorporated into the systems engineering process to everyone's satisfaction.

Integrated support structure for GASCAN 2

NASA Technical Reports Server (NTRS)

1990-01-01

The focus of the Worcester Polytechnic Institute (WPI) Advanced Space Design Program was the preliminary design of the Integrated Support Structure for GASCAN II, a Get Away Special canister donated by the MITRE Corporation. Two teams of three students each worked on the support structure. There was a structural design team and a thermal design team. The structure will carry three experiments also undergoing preliminary design this year, the mu-gravity Ignition Experiment, the Rotational Flow in Low Gravity Experiment, and the Ionospheric Properties and Propagation Experiment. The structural design team was responsible for the layout of the GASCAN and the preliminary design of the structure itself. They produced the physical interface specifications defining the baseline weights and volumes for the equipment and produced layout drawings of the system. The team produced static and modal finite element analysis of the structure using ANSYS. The thermal design team was responsible for the power and timing requirements of the payload and for the identification and preliminary analysis of potential thermal problems. The team produced the power, timing, and energy interface specifications and assisted in the development of the specification of the battery pack. The thermal parameters of each experiment were cataloged and the experiments were subjected to worst case heat transfer scenarios.

Preliminary investigations of protein crystal growth using the Space Shuttle

NASA Technical Reports Server (NTRS)

Delucas, L. J.; Suddath, F. L.; Snyder, R.; Naumann, R.; Broom, M. B.; Pusey, M.; Yost, V.; Herren, B .; Carter, D.

1986-01-01

Four preliminary Shuttle experiments are described which have been used to develop prototype hardware for a more advanced system that will evaluate effects of gravity on protein crystal growth. The first phase of these experiments has centered on the development of micromethods for protein crystal growth by vapor-diffusion techniques (using a space version of the hanging-drop method) and on dialysis using microdialysis cells. Results suggest that the elimination of density-driven sedimentation can effect crystal morphology. In the dialysis experiment, space-grown crystals of concanavalin B were three times longer and 1/3 the thickness of earth-grown crystals.

Preliminary technical results review of FY81 experiments. Volume 1: Fiscal year 1981/82 spring small grains pilot experiment. [Canada and the United States

NASA Technical Reports Server (NTRS)

1981-01-01

Technical progress made in the foreign commodity production forecasting for the advancement of spring small grains (SSG) area estimation is reported with emphasis on results achieved since the last AgRISTARS level semiannual review. Major objectives and accomplishments are reviewed and the experiment is described. The technical approach data assessment, and data systems used are considered. Results of the group approach comparison study are presented along with preliminary aggregation results for SSG processing procedures. The outlook for the future is assessed.

Motivation for proposed experimentation in the realm of accelerated E. M. systems: A preliminary design for an experiment

NASA Technical Reports Server (NTRS)

Post, E. J.

1970-01-01

An experiment, designed to determine the difference between fields-magnetic and electric-surrounding a uniformly moving charge as contrasted with the fields surrounding an accelerated charge, is presented. A thought experiment is presented to illustrate the process.

Preliminary Results from the AFRL-NASA W/V-Band Terrestrial Link Experiment in Albuquerque, NM

NASA Technical Reports Server (NTRS)

Zemba, Michael; Nessel, James; Houts, Jacquelynne; Tarasenko, Nicholas; Lane, Steven; Murrell, David

2016-01-01

Atmospheric propagation models and the measurements that train them are critical to the design of efficient and effective space-ground links. As communication systems advance to higher frequencies in search of higher data rates and open spectrum, a lack of data at these frequencies necessitates new measurements to properly develop, validate, and refine the models used for link budgeting and system design. In collaboration with the Air Force Research Laboratory (AFRL), NASA Glenn Research Center has deployed the WV-band Terrestrial Link Experiment (WTLE) in Albuquerque, NM to conduct a measurement campaign at 72 and 84 GHz, among the first atmospheric propagation measurements at these frequencies. WTLE has been operational since October 1, 2015, and the system design shall be herein discussed alongside preliminary results and performance.

Dynamic resource allocation in a hierarchical multiprocessor system: A preliminary study

NASA Technical Reports Server (NTRS)

Ngai, Tin-Fook

1986-01-01

An integrated system approach to dynamic resource allocation is proposed. Some of the problems in dynamic resource allocation and the relationship of these problems to system structures are examined. A general dynamic resource allocation scheme is presented. A hierarchial system architecture which dynamically maps between processor structure and programs at multiple levels of instantiations is described. Simulation experiments were conducted to study dynamic resource allocation on the proposed system. Preliminary evaluation based on simple dynamic resource allocation algorithms indicates that with the proposed system approach, the complexity of dynamic resource management could be significantly reduced while achieving reasonable effective dynamic resource allocation.

Advanced Method of Boundary-Layer Control Based on Localized Plasma Generation

DTIC Science & Technology

2009-05-01

measurements, validation of experiments, wind-tunnel testing of the microwave / plasma generation system , preliminary assessment of energy required...and design of a microwave generator , electrodynamic and multivibrator systems for experiments in the IHM-NAU wind tunnel: MW generator and its high...equipped with the microwave - generation and protection systems to study advanced methods of flow control (Kiev) Fig. 2.1,a. The blade

Earth Sciences Requirements for the Information Sciences Experiment System

NASA Technical Reports Server (NTRS)

Bowker, David E. (Editor); Katzberg, Steve J. (Editor); Wilson, R. Gale (Editor)

1990-01-01

The purpose of the workshop was to further explore and define the earth sciences requirements for the Information Sciences Experiment System (ISES), a proposed onboard data processor with real-time communications capability intended to support the Earth Observing System (Eos). A review of representative Eos instrument types is given and a preliminary set of real-time data needs has been established. An executive summary is included.

(Re)Conceptualizing "Dropouts" from Narratives of Black High School Students in Ontario.

ERIC Educational Resources Information Center

Dei, George J. Sefa

The preliminary findings of an on-going 3-year study examining the experiences of black students in a Canadian public school system are discussed. The project has been using students' narratives of their experiences in an inner-city public school system to explore the influences of race/ethnicity, class, gender, power, and social structures on…

Sounding-Diagnosed Convective Environments and Preliminary Energy Budgets Diagnosed during the TRMM Field Campaigns

NASA Technical Reports Server (NTRS)

Halverson, Jeffrey B.; Roy, Biswadev; O'CStarr, David (Technical Monitor)

2002-01-01

An overview of mean convective thermodynamic and wind profiles for the Tropical Rainfall Measuring Mission (TRMM) Large Scale Biosphere-Atmosphere Experiment (LBA) and Kwajalein Experiment (KWAJEX) field campaigns will be presented, highlighting the diverse continental and marine tropical environments in which rain clouds and mesoscale convective systems evolved. An assessment of ongoing sounding quality control procedures will be shown. Additionally, we will present preliminary budgets of sensible heat source (Q1) and apparent moisture sink (Q2), which have been diagnosed from the various sounding networks.

Developing Systems Engineering Experience Accelerator (SEEA) Prototype and Roadmap -- Increment 4

DTIC Science & Technology

2017-08-08

of an acquisition program, two categories of new capabilities were added to the UAV experience. Based on a student project at Stevens Institute of...program for a new unmanned aerial vehicle (UAV) system. It was based on the concept of the learners assuming this role shortly after preliminary...University curriculum for systems engineers. First, several new capabilities have been added. These include a trade study for additional technical

Data processing system for the Sneg-2MP experiment

NASA Technical Reports Server (NTRS)

Gavrilova, Y. A.

1980-01-01

The data processing system for scientific experiments on stations of the "Prognoz" type provides for the processing sequence to be broken down into a number of consecutive stages: preliminary processing, primary processing, secondary processing. The tasks of each data processing stage are examined for an experiment designed to study gamma flashes of galactic origin and solar flares lasting from several minutes to seconds in the 20 kev to 1000 kev energy range.

Preliminary experiments on pharmacokinetic diffuse fluorescence tomography of CT-scanning mode

NASA Astrophysics Data System (ADS)

Zhang, Yanqi; Wang, Xin; Yin, Guoyan; Li, Jiao; Zhou, Zhongxing; Zhao, Huijuan; Gao, Feng; Zhang, Limin

2016-10-01

In vivo tomographic imaging of the fluorescence pharmacokinetic parameters in tissues can provide additional specific and quantitative physiological and pathological information to that of fluorescence concentration. This modality normally requires a highly-sensitive diffuse fluorescence tomography (DFT) working in dynamic way to finally extract the pharmacokinetic parameters from the measured pharmacokinetics-associated temporally-varying boundary intensity. This paper is devoted to preliminary experimental validation of our proposed direct reconstruction scheme of instantaneous sampling based pharmacokinetic-DFT: A highly-sensitive DFT system of CT-scanning mode working with parallel four photomultiplier-tube photon-counting channels is developed to generate an instantaneous sampling dataset; A direct reconstruction scheme then extracts images of the pharmacokinetic parameters using the adaptive-EKF strategy. We design a dynamic phantom that can simulate the agent metabolism in living tissue. The results of the dynamic phantom experiments verify the validity of the experiment system and reconstruction algorithms, and demonstrate that system provides good resolution, high sensitivity and quantitativeness at different pump speed.

Protein crystal growth in microgravity

NASA Technical Reports Server (NTRS)

Rosenblum, William M.; Delucas, Lawrence J.; Wilson, William W.

1989-01-01

Major advances have been made in several of the experimental aspects of protein crystallography, leaving protein crystallization as one of the few remaining bottlenecks. As a result, it has become important that the science of protein crystal growth is better understood and that improved methods for protein crystallization are developed. Preliminary experiments with both small molecules and proteins indicate that microgravity may beneficially affect crystal growth. For this reason, a series of protein crystal growth experiments using the Space Shuttle was initiated. The preliminary space experiments were used to evolve prototype hardware that will form the basis for a more advanced system that can be used to evaluate effects of gravity on protein crystal growth. Various optical techniques are being utilized to monitor the crystal growth process from the incipient or nucleation stage and throughout the growth phase. The eventual goal of these studies is to develop a system which utilizes optical monitoring for dynamic control of the crystallization process.

Test and evaluation of Apollo 14 composite casting demonstration specimens and flight and control samples

NASA Technical Reports Server (NTRS)

Fabiniak, R. C.; Fabiniak, T. J.

1971-01-01

The results of experiments 1, 2, and 10 of the Apollo 14 composite casting demonstration are discussed. The purpose of the demonstration, with regard to samples 1 and 2, was to obtain preliminary data on the liquid phase sintering process in a weightless environment. With regard to sample 10, the purpose was to obtain preliminary information on how to achieve uniform dispersion of dense particles on a metal matrix by employing shaking modes or forces in the system when the metal matrix is molten. Results of the demonstrations were interpreted in a quantitative and qualitative manner. For experiment 1 it was found that the tungsten particles were redistributed more uniformly in the flight sample than in the control sample. Experiment 2 results indicate that complete melting may not have occured and thus a high degree of significance cannot be associated with the qualitative results relating to particle redistribution data. The particle-matrix system of experiment 10 was found to be nonwetting.

The Windy Island Soliton Experiment (WISE): Shallow Water and Basin Experiment Configuration and Preliminary Observations

DTIC Science & Technology

2009-02-19

Virginia 22203-1995 The Windy Island Soliton Experiment (WISE): Shallow Water and Basin Experiment Configuration and Preliminary Observations...case letters) The Windy Island Soliton Experiment (WISE): Shallow water and Basin Experiment Configuration and Preliminary Observations 5. FUNDING...release; distribution is unlimited 12b. DISTRIBUTION CODE 13. ABSTRACT (maximum 200 words) The Windy Islands Soliton Experiment (WISE) was

Preliminary experience with a stereoscopic video system in a remotely piloted aircraft application

NASA Technical Reports Server (NTRS)

Rezek, T. W.

1983-01-01

Remote piloting video display development at the Dryden Flight Research Facility of NASA's Ames Research Center is summarized, and the reasons for considering stereo television are presented. Pertinent equipment is described. Limited flight experience is also discussed, along with recommendations for further study.

LDEF: 69 Months in Space. First Post-Retrieval Symposium, part 2

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1992-01-01

A compilation of papers from the symposium is presented. The preliminary data analysis is presented of the 57 experiments flown on the LDEF. The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, and micrometeoroid), electronics, optics, and life science.

Synthesis and analysis of precise spaceborne laser ranging systems, volume 2. [Spacelab payload

NASA Technical Reports Server (NTRS)

Paddon, E. A.

1978-01-01

The performance capabilities of specific shuttle-based laser ranging systems were evaluated, and interface and support requirements were determined. The preliminary design of a shuttle-borne laser ranging experiment developed as part of the Spacelab program is discussed.

An expert system/ion trap mass spectrometry approach for life support systems monitoring

NASA Technical Reports Server (NTRS)

Palmer, Peter T.; Wong, Carla M.; Yost, Richard A.; Johnson, Jodie V.; Yates, Nathan A.; Story, Michael

1992-01-01

Efforts to develop sensor and control system technology to monitor air quality for life support have resulted in the development and preliminary testing of a concept based on expert systems and ion trap mass spectrometry (ITMS). An ITMS instrument provides the capability to identify and quantitate a large number of suspected contaminants at trace levels through the use of a variety of multidimensional experiments. An expert system provides specialized knowledge for control, analysis, and decision making. The system is intended for real-time, on-line, autonomous monitoring of air quality. The key characteristics of the system, performance data and analytical capabilities of the ITMS instrument, the design and operation of the expert system, and results from preliminary testing of the system for trace contaminant monitoring are described.

Vapor transport mechanisms

NASA Technical Reports Server (NTRS)

Workman, G. L.

1978-01-01

The Raman scattering furnace for investigating vapor transport mechanisms was completed and checked out. Preliminary experiments demonstate that a temperature resolution of plus and minus 5 C is possible with this system operating in a backscatter mode. In the experiments presented with the GeI 4 plus excess Ge system at temperatures up to 600 C, only the GeI4 band at 150 cm superscript minus 1 was observed. Further experiments are in progress to determine if GeI2 does become the major vapor species above 440 C.

Preliminary Assessment of the Nutrient Film Technique for Wastewater Treatment

DTIC Science & Technology

1982-03-01

umre) Hydroponics Thin films Wastes (Sanitary engineering) \\Waslewater \\I MArWIASSACr a m evemww sb N nem y., d idenif, by block nm,6...) An experiment...best described attach themselves. as a modified hydroponic system in which a thin film of nutrient solution flows through the root mat of Purpose plants...of an experiment conducted at CRREL to de- tween an NFT system and a hydroponic plant system termine the feasibility of using the nutrient film tech

Preliminary experiments to quantify liquid movement under mimetic vocal fold vibrational forces.

PubMed

Titze, Ingo R; Klemuk, Sarah; Lu, Xiaoying

2014-07-01

Hydration of vocal fold tissues is essential for self-sustained oscillation. Normal regulatory processes of liquid transport to and from the vocal folds would be expected through the autonomic systems, but the possibility exists that liquid movement may occur locally due to vibrational pressures. Such movement may cause regions of lower or higher concentrations of liquid viscosity and therewith changes in phonation threshold pressure. Hyaluronic acid, a glycosaminoglycan that attracts large quantities of free water, may be a key molecule for transporting or localizing liquids. Some preliminary experiments are reported in which attempts were made to move low-concentration HA liquids with vibration. None of the experiments was conclusive, but collectively they lay some groundwork for future explorations.

Preliminary experience in laparoscopic resection of hepatic hydatidectocyst with the Da Vinci Surgical System (DVSS): a case report.

PubMed

Zou, Haibo; Luo, Lanyun; Xue, Hua; Wang, Guan; Wang, Xiankui; Luo, Le; Yao, Yutong; Xiang, Guangming; Huang, Xiaolun

2017-09-11

At present, Da Vinci robotic assisted hepatectomy has been routinely carried out in conditional units. But there is no report concerning the use of Da Vinci robots for hepatic hydatid cystectomy and experience on this aspect is seldom mentioned before. This study was to summarize the preliminary experience in laparoscopic resection of hepatic hydatidectocyst with the Da Vinci Surgical System (DVSS). A 29-year-old female diagnosed as hepatic hydatid in the right anterior lobe of liver was treated with laparoscopic resection by the DVSS under general anesthesia. Appropriate disposal of tumor cell in vascular system and disinfection of surgical field with hypertonic saline were conducted. The hepatic hydatidectocyst was resected completely with an operation time of 130 min, an intraoperative blood loss of 200 ml and a length of hospital stay for five days. The vital signs of patient were stable and no cyst fluid allergy occurred after operation. Our result showed that laparoscopic resection of hepatic hydatidectocyst by using the DVSS is safe and feasible on the basis of hospitals have rich experience in treatment of cystic echinococcosisliver, resection with DVSS and laparoscopic excision.

Parametric analyses of planned flowing uranium hexafluoride critical experiments

NASA Technical Reports Server (NTRS)

Rodgers, R. J.; Latham, T. S.

1976-01-01

Analytical investigations were conducted to determine preliminary design and operating characteristics of flowing uranium hexafluoride (UF6) gaseous nuclear reactor experiments in which a hybrid core configuration comprised of UF6 gas and a region of solid fuel will be employed. The investigations are part of a planned program to perform a series of experiments of increasing performance, culminating in an approximately 5 MW fissioning uranium plasma experiment. A preliminary design is described for an argon buffer gas confined, UF6 flow loop system for future use in flowing critical experiments. Initial calculations to estimate the operating characteristics of the gaseous fissioning UF6 in a confined flow test at a pressure of 4 atm, indicate temperature increases of approximately 100 and 1000 K in the UF6 may be obtained for total test power levels of 100 kW and 1 MW for test times of 320 and 32 sec, respectively.

Daily Life Experience and Somatic Symptoms: A Preliminary Report.

DTIC Science & Technology

1981-03-01

AAO7 9 859 STATE UNIV OF NEW YORK AT STONY BROOK FG 5/10 DAILY LIFE EXPERIENCE AND SOMATIC SYMPTOMS: A PRELIMINARY REPOR--ETC(U) MAR 8I A A STONE. J...Experience and Somatic Symptoms: A Preliminary Report Arthur A. Stone Long Island Research Institute and Department of Psychiatry arnd Behavioral...TITLE (and S..,til.) s. ALF - , rlA9OQ COVERED Daily Life Experience and Somatic Symptoms: A Technical p " Preliminary Report, EL..... S. PERFORMING

Spread spectrum time-resolved diffuse optical measurement system for enhanced sensitivity in detecting human brain activity

NASA Astrophysics Data System (ADS)

Mehta, Kalpesh; Hasnain, Ali; Zhou, Xiaowei; Luo, Jianwen; Penney, Trevor B.; Chen, Nanguang

2017-04-01

Diffuse optical spectroscopy (DOS) and imaging methods have been widely applied to noninvasive detection of brain activity. We have designed and implemented a low cost, portable, real-time one-channel time-resolved DOS system for neuroscience studies. Phantom experiments were carried out to test the performance of the system. We further conducted preliminary human experiments and demonstrated that enhanced sensitivity in detecting neural activity in the cortex could be achieved by the use of late arriving photons.

LDEF: 69 Months in Space. First Post-Retrieval Symposium, part 1

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1992-01-01

A compilation of papers from the symposium is presented. The papers represent the preliminary data analysis of the 57 experiments flown on the Long Duration Exposure Facility (LDEF). The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, and micrometeoroids), electronics, optics, and life sciences.

New Telecommunication Uses in Tama, New Town. Summary.

ERIC Educational Resources Information Center

Komatsuzaki, Seisuke

This paper deals with a Test Information Service which is being tried out in Tama, Japan. The large scale field experiment of the new telecommunication system is called Coaxial Cable Information Service (CCIS) and was started in 1976. Preliminary findings included that: 1) users are interested in the experiment; 2) two-way communication systems…

Preliminary plan for a Shuttle Coherent Atmospheric Lidar Experiment (SCALE)

NASA Technical Reports Server (NTRS)

Fitzjarrald, D.; Beranek, R.; Bilbro, J.; Mabry, J.

1985-01-01

A study has been completed to define a Shuttle experiment that solves the most crucial scientific and engineering problems involved in building a satellite Doppler wind profiler for making global wind measurements. The study includes: (1) a laser study to determine the feasibility of using the existing NOAA Windvan laser in the Space Shuttle spacecraft; (2) a preliminary optics and telescope design; (3) an accommodations study including power, weight, thermal, and control system requirements; and (4) a flight trajectory and operations plan designed to accomplish the required scientific and engineering goals. The experiment will provide much-needed data on the global distribution of atmospheric aerosols and demonstrate the technique of making wind measurements from space, including scanning the laser beam and interpreting the data. Engineering accomplishments will include space qualification of the laser, development of signal processing and lag angle compensation hardware and software, and telescope and optics design. All of the results of this limited Spacelab experiment will be directly applicable to a complete satellite wind profiler for the Earth Observation System/Space Station or other free-flying satellite.

Experiment module concepts study. Volume 2: Experiments and mission operations

NASA Technical Reports Server (NTRS)

Macdonald, J. M.

1970-01-01

The baseline experiment program is concerned with future space experiments and cover the scientific disciplines of astronomy, space physics, space biology, biomedicine and biotechnology, earth applications, materials science, and advanced technology. The experiments within each discipline are grouped into functional program elements according to experiments that support a particular area of research or investigation and experiments that impose similar or related demand on space station support systems. The experiment requirements on module subsystems, experiment operating modes and time profiles, and the role of the astronaut are discussed. Launch and rendezvous with the space station, disposal, and on-orbit operations are delineated. The operational interfaces between module and other system elements are presented and include space station and logistic system interfaces. Preliminary launch and on-orbit environmental criteria and requirements are discussed, and experiment equipment weights by functional program elements are tabulated.

Observing system simulations using synthetic radiances and atmospheric retrievals derived for the AMSU and HIRS in a mesoscale model. [Advanced Microwave Sounding Unit

NASA Technical Reports Server (NTRS)

Diak, George R.; Huang, Hung-Lung; Kim, Dongsoo

1990-01-01

The paper addresses the concept of synthetic satellite imagery as a visualization and diagnostic tool for understanding satellite sensors of the future and to detail preliminary results on the quality of soundings from the current sensors. Preliminary results are presented on the quality of soundings from the combination of the High-Resolution Infrared Radiometer Sounder and the Advanced Microwave Sounding Unit. Results are also presented on the first Observing System Simulation Experiment using this data in a mesoscale numerical prediction model.

AgRISTARS. Preliminary technical results review of FY81 experiments, volume 2: Fiscal year 1981/1982 "corn and soybeans pilot" experiment

NASA Technical Reports Server (NTRS)

1981-01-01

The performance of the technology exhibited significant proportion estimation errors, specifically, high mean error in both corn and soybeans area estimation. The data systems, technical approaches, and data assessment of the pilot experiment were reviewed. Results of proportion estimations procedure performance evaluations, and sensitivity evaluations are presented. The role of the pilot experiment in foreign technology development is discussed.

A six-degree-of-freedom passive arm with dynamic constraints (PADyC) for cardiac surgery application: preliminary experiments.

PubMed

Schneider, O; Troccaz, J

2001-01-01

The purpose of Computer-Assisted Surgery (CAS) is to help physicians and surgeons plan and execute optimal strategies from multimodal image data. The execution of such planned strategies may be assisted by guidance systems. Some of these systems, called synergistic systems, are based on the cooperation of a robotic device with a human operator. We have developed such a synergistic device: PADyC (Passive Arm with Dynamic Constraints). The basic principle of PADyC is to have a manually actuated arm that dynamically constrains the authorized motions of the surgical tool held by the human operator during a planned task. Dynamic constraints are computed from the task definition, and are implemented by a patented mechanical system. In this paper, we first introduce synergistic systems and then focus on modeling and algorithmic issues related to the dynamic constraints. Finally, we describe a 6-degree-of-freedom prototype robot designed for a clinical application (cardiac surgery) and report on preliminary experiments to date. The experimental results are then discussed, and future work is proposed. Copyright 2002 Wiley-Liss, Inc.

Bistatic radar sea state monitoring

NASA Technical Reports Server (NTRS)

Ruck, G. T.; Barrick, D. E.; Kaliszewski, T.

1972-01-01

Bistatic radar techniques were examined for remote measurement of the two-dimensional surface wave height spectrum of the ocean. One technique operates at high frequencies (HF), 3-30 MHz, and the other at ultrahigh frequencies (UHF), approximately 1 GHz. Only a preliminary theoretical examination of the UHF technique was performed; however the principle underlying the HF technique was demonstrated experimentally with results indicating that an HF bistatic system using a surface transmitter and an orbital receiver would be capable of measuring the two-dimensional wave height spectrum in the vicinity of the transmitter. An HF bistatic system could also be used with an airborne receiver for ground truth ocean wave spectrum measurements. Preliminary system requirements and hardware configurations are discussed for both an orbital system and an aircraft verification experiment.

Student Satisfaction or Happiness?: A Preliminary Rethink of What Is Important in the Student Experience

ERIC Educational Resources Information Center

Dean, Aftab; Gibbs, Paul

2015-01-01

Purpose: This paper aims to investigate the purpose of the complex open system of higher education and to explore this transformative experience as personal flourishing, where students come to terms with a way of being, matching their potentiality with their agency and leading to profound happiness. There is influential, but not uncontested…

A space station Structures and Assembly Verification Experiment, SAVE

NASA Technical Reports Server (NTRS)

Russell, R. A.; Raney, J. P.; Deryder, L. J.

1986-01-01

The Space Station structure has been baselined to be a 5 M (16.4 ft) erectable truss. This structure will provide the overall framework to attach laboratory modules and other systems, subsystems and utilities. The assembly of this structure represents a formidable EVA challenge. To validate this capability the Space Station Structures/Dynamics Technical Integration Panel (TIP) met to develop the necessary data for an integrated STS structures flight experiment. As a result of this meeting, the Langley Research Center initiated a joint Langley/Boeing Aerospace Company study which supported the structures/dynamics TIP in developing the preliminary definition and design of a 5 M erectable space station truss and the resources required for a proposed flight experiment. The purpose of the study was to: (1) devise methods of truss assembly by astronauts; (2) define a specific test matrix for dynamic characterization; (3) identify instrumentation and data system requirements; (4) determine the power, propulsion and control requirements for the truss on-orbit for 3 years; (5) study the packaging of the experiment in the orbiter cargo bay; (6) prepare a preliminary cost estimate and schedule for the experiment; and (7) provide a list of potential follow-on experiments using the structure as a free flyer. The results of this three month study are presented.

Home Exercise in a Social Context: Real-Time Experience Sharing Using Avatars

NASA Astrophysics Data System (ADS)

Aghajan, Yasmin; Lacroix, Joyca; Cui, Jingyu; van Halteren, Aart; Aghajan, Hamid

This paper reports on the design of a vision-based exercise monitoring system. The system aims to promote well-being by making exercise sessions enjoyable experiences, either through real-time interaction and instructions proposed to the user, or via experience sharing or group gaming with peers in a virtual community. The use of avatars is explored as means of representation of the user’s exercise movements or appearance, and the system employs user-centric approaches in visual processing, behavior modeling via history data accumulation, and user feedback to learn the preferences. A preliminary survey study has been conducted to explore the avatar preferences in two user groups.

On-line prediction of yield grade, longissimus muscle area, preliminary yield grade, adjusted preliminary yield grade, and marbling score using the MARC beef carcass image analysis system.

PubMed

Shackelford, S D; Wheeler, T L; Koohmaraie, M

2003-01-01

The present experiment was conducted to evaluate the ability of the U.S. Meat Animal Research Center's beef carcass image analysis system to predict calculated yield grade, longissimus muscle area, preliminary yield grade, adjusted preliminary yield grade, and marbling score under commercial beef processing conditions. In two commercial beef-processing facilities, image analysis was conducted on 800 carcasses on the beef-grading chain immediately after the conventional USDA beef quality and yield grades were applied. Carcasses were blocked by plant and observed calculated yield grade. The carcasses were then separated, with 400 carcasses assigned to a calibration data set that was used to develop regression equations, and the remaining 400 carcasses assigned to a prediction data set used to validate the regression equations. Prediction equations, which included image analysis variables and hot carcass weight, accounted for 90, 88, 90, 88, and 76% of the variation in calculated yield grade, longissimus muscle area, preliminary yield grade, adjusted preliminary yield grade, and marbling score, respectively, in the prediction data set. In comparison, the official USDA yield grade as applied by online graders accounted for 73% of the variation in calculated yield grade. The technology described herein could be used by the beef industry to more accurately determine beef yield grades; however, this system does not provide an accurate enough prediction of marbling score to be used without USDA grader interaction for USDA quality grading.

A mobile system for active otpical pollution monitoring

NASA Technical Reports Server (NTRS)

Sunesson, A.; Edner, H.; Svanberg, S.; Uneus, L.; Wendt, W.; Fredriksson, K.

1986-01-01

The remote monitoring of atmospheric pollutants can now be performed in several ways. Laser radar techniques have proven their ability to reveal the spatial distribution of different species or particles. Classical optical techniques can also be used, but yield the average concentration over a given path and hence no range resolution. One such technique is Differential Optical Absorption Spectroscopy, DOAS. Such schemes can be used to monitor paths that a preliminary lidar investigation has shown to be of interest. Having previously had access to a mobile lidar system, a new system has been completed. The construction builds on experience from using the other system and it is meant to be more of a mobile optical laboratory than just a lidar system. A complete system description is given along with some preliminary usage. Future uses are contemplated.

Preliminary Concept, Specifications, and Requirements for a Zero-Gravity Combustion Facility for Spacelab

NASA Technical Reports Server (NTRS)

Dewitt, Richard L.

1978-01-01

The preliminary concept, specifications, and requirements of a reusable zero gravity combustion facility (0-GCF) for use by experimenters aboard the spacelab payload of the space transportation system (STS) orbiter are described. The facility will be amenable to any mission of the STS orbiter in which a spacelab habitable segment and pallet segment are integral and for which orbital mission plans specify induced accelerations of 0.0001 g or less for sufficiently long periods so as not to impact experiment performance.

Feasibilty analyses of electroepitaxial research and development accomodations. Volume 1: Accommodations assessment

NASA Technical Reports Server (NTRS)

1983-01-01

A preliminary assessment of the feasibility of accommodating the on-orbit R&D requirements for electroepitaxial crystal growth using the Orbiter middeck, the Materials Experiment Assembly or the Get-Away Special cans was performed. The study is based on the proposed electroepitaxial growth of single crystals of gallium arsenide (GaAs). Baseline R&D requirements, synthesizing furnace and facility conceptual design requirements, accommodation requirements, preliminary compatibility assessments are established. The systems engineering approach employed for the individual assessments is outlined.

A preliminary investigation of the Environmental Control and Life Support Subsystem (EC/LSS) for the space construction base manufacturing modules

NASA Technical Reports Server (NTRS)

Wells, H. B.

1977-01-01

The preliminary data of the environmental control and life support subsystem for a space construction base manufacturing module was reported. A space processing module, which is capable of performing production biological experiments, was chosen as a baseline configuration. The primary assemblies and components considered for use were humidity and temperature control, ventilation fan, cabin fan, water separator, condensate storage, overboard dumping, distribution system, contaminant monitoring, cabin sensors, and fire and smoke detection.

MSFC integrated experiments preliminary report. [for the Skylab program

NASA Technical Reports Server (NTRS)

1974-01-01

Skylab experiments are described and their preliminary results are reported. The types of experiments described include medical, earth resources, space physics, space manufacturing, and spacecraft design.

Light and Gravity Effects on Circadian Rhythms of Rhesus Macaques

NASA Technical Reports Server (NTRS)

Fuller, Charles

1997-01-01

Temporal integration of a biological organism's physiological, behavioral and biochemical systems depends upon its circadian timing system. The endogenous period of this timing system is typically synchronized to the 24- hour day by environmental cues. The daily alternation of light and dark has long been known as one of the most potent environmental synchronizers influencing the circadian timing system. Alterations in the lighting environment (length or intensity of light exposure) can also affect the homeostatic state of the organism. A series of experiments was performed using rhesus monkeys with the objective of defining the fundamental properties of the circadian rhythm of body temperature. Three major experiments were performed in addition to several preliminary studies. These experiments explored 1.) the response of the rhesus body temperature rhythm to varying day length and light intensity; 2.) the response of the body temperature rhythm to light exposure as a function of time of day; and 3.) the characteristics of the metabolic heat production rhythm which is responsible for the daily cycle in body temperature. Results of these three completed experiments will be reported here. In addition, preliminary experiments were also performed in social entrainment of rhesus circadian rhythms and the properties of rhesus body temperature rhythms in constant conditions, where no external time cues were provided. Four adult male rhesus monkeys served as subjects in all experiments. All experiments were performed at the California Regional Primate Research Center. Each animal was implanted with a biotelemetry unit that measured deep body temperature. All surgeries were performed by a board certified veterinary surgeon under sterile conditions. The biotelemetry implants also provided an index of activity level in each animal. For metabolic heat production measurements, oxygen consumption and carbon dioxide production were measured and the caloric equivalent of these was calculated. Specific methodologies are described in detail.

Automated space processing payloads study. Volume 2, book 2: Technical report, appendices A through E. [instrument packages and space shuttles

NASA Technical Reports Server (NTRS)

1975-01-01

Experiment hardware and operational requirements for space shuttle experiments are discussed along with payload and system concepts. Appendixes are included in which experiment data sheets, chamber environmental control and monitoring, method for collection and storage of electrophoretically-separated samples, preliminary thermal evaluation of electromagnetic levitation facilities L1, L2, and L3, and applicable industrial automation equipment are discussed.

LDEF: 69 Months in Space. First Post-Retrieval Symposium, part 3

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1992-01-01

A compilation of papers presented at the First Long Duration Exposure Facility (LDEF) Post-Retrieval Symposium is presented. The papers represent the preliminary data analysis of the 57 experiments flown on the LDEF. The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, and micrometeoroid), electronics, optics, and life sciences.

Electrically Driven Liquid Film Boiling Experiment

NASA Technical Reports Server (NTRS)

Didion, Jeffrey R.

2016-01-01

This presentation presents the science background and ground based results that form the basis of the Electrically Driven Liquid Film Boiling Experiment. This is an ISS experiment that is manifested for 2021. Objective: Characterize the effects of gravity on the interaction of electric and flow fields in the presence of phase change specifically pertaining to: a) The effects of microgravity on the electrically generated two-phase flow. b) The effects of microgravity on electrically driven liquid film boiling (includes extreme heat fluxes). Electro-wetting of the boiling section will repel the bubbles away from the heated surface in microgravity environment. Relevance/Impact: Provides phenomenological foundation for the development of electric field based two-phase thermal management systems leveraging EHD, permitting optimization of heat transfer surface area to volume ratios as well as achievement of high heat transfer coefficients thus resulting in system mass and volume savings. EHD replaces buoyancy or flow driven bubble removal from heated surface. Development Approach: Conduct preliminary experiments in low gravity and ground-based facilities to refine technique and obtain preliminary data for model development. ISS environment required to characterize electro-wetting effect on nucleate boiling and CHF in the absence of gravity. Will operate in the FIR - designed for autonomous operation.

Preliminary measurements of 135Cs with AMS

NASA Astrophysics Data System (ADS)

Yin, Xinyi; He, Ming; Dong, Kejun; Dou, Liang; Lan, Xiaoxi; Pang, Fangfang; Wu, Shaoyong; Jiang, Shan

2015-10-01

135Cs is an interesting nuclide in many research fields, especially in environmental study. Preliminary measurements of the long-lived 135Cs with accelerator mass spectrometry (AMS) have been developed with the HI-13 tandem AMS facility at China Institute of Atomic Energy (CIAE). In order to improve ion extracting current and depressing background interference, experiments were carried out on different ions of Cs extracted from different samples. It was found that Cs- extracted from CsNO3 can be used for AMS measurement of 135Cs. According to the preliminary results, the background level can be obtained with blanks was 135Ba/Cs ∼ 8.8 × 10-12 with the CIAE-AMS system.

Final definition and preliminary design study for the initial atmospheric cloud physics laboratory, a Spacelab mission payload

NASA Technical Reports Server (NTRS)

1976-01-01

The following areas related to the final definition and preliminary design study of the initial atmospheric cloud physics laboratory (ACPL) were covered: (1) proposal organization, personnel, schedule, and project management, (2) proposed configurations, (3) study objectives, (4) ACPL experiment program listing and description, (5) mission/flight flexibility and modularity/commonality, (6) study plan, and (7) description of following tasks: requirement analysis and definition task flow, systems analysis and trade studies, subsystem analysis and trade studies, specifications and interface control documents, preliminary design task flow, work breakdown structure, programmatic analysis and planning, and project costs. Finally, an overview of the scientific requirements was presented.

Army gas-cooled reactor systems program. Preliminary design report off-normal scram system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bushnell, W.H.; Malmstrom, S.A.

1965-06-01

The maximum allowable ML-1 fuel element cladding (hot spot) temperature is established by ANTS 201 at 1750/sup 0/F. The existing ML-1 design makes no provision for automatic scram when this limit is reached. Operating experience has indicated a requirement for such an automatic system during plant startup and a revised hot spot envelope (generated during conceptual design of the scram system) established the desirability of extending this protection to operation at full power conditions. It was also determined that the scram system should include circuitry to initiate an automatic scram if reactor ..delta..T exceeded 450/sup 0/F (the limit established inmore » ANTS 201) and if reactor power exceeded 6 kw(t) without coolant flow in the main loop. The preliminary design of the scram system (designated off-normal scram system) which will provide the required protection is described.« less

System safety checklist Skylab program report

NASA Technical Reports Server (NTRS)

Mcnail, E. M.

1974-01-01

Design criteria statement applicable to a wide variety of flight systems, experiments and other payloads, associated ground support equipment and facility support systems are presented. The document reflects a composite of experience gained throughout the aerospace industry prior to Skylab and additional experience gained during the Skylab Program. It has been prepared to provide current and future program organizations with a broad source of safety-related design criteria and to suggest methods for systematic and progressive application of the criteria beginning with preliminary development of design requirements and specifications. Recognizing the users obligation to shape the checklist to his particular needs, a summary of the historical background, rationale, objectives, development and implementation approach, and benefits based on Skylab experience has been included.

LDEF active optical system components experiment

NASA Technical Reports Server (NTRS)

Blue, M. D.

1992-01-01

A preliminary report on the Active Optical System Components Experiment is presented. This experiment contained 136 components in a six inch deep tray including lasers, infrared detectors and arrays, ultraviolet light detectors, light-emitting diodes, a light modulator, flash lamps, optical filters, glasses, and samples of surface finishes. Thermal, mechanical, and structural considerations leading to the design of the tray hardware are discussed. In general, changes in the retested component characteristics appear as much related to the passage of time as to the effects of the space environment, but organic materials, multilayer optical interference filters, and extreme-infrared reflectivity of black paints show unexpected changes.

Decision-Making in Flight with Different Convective Weather Information Sources: Preliminary Results

NASA Technical Reports Server (NTRS)

Latorella, Kara A.; Chamberlain, James P.

2004-01-01

This paper reports preliminary and partial results of a flight experiment to address how General Aviation (GA) pilots use weather cues to make flight decisions. This research presents pilots with weather cue conditions typically available to GA pilots in visual meteorological conditions (VMC) and instrument meteorological conditions (IMC) today, as well as in IMC with a Graphical Weather Information System (GWIS). These preliminary data indicate that both VMC and GWIS-augmented IMC conditions result in better confidence, information sufficiency and perceived performance than the current IMC condition. For all these measures, the VMC and GWIS-augmented conditions seemed to provide similar pilot support. These preliminary results are interpreted for their implications on GWIS display design, training, and operational use guidelines. Final experimental results will compare these subjective data with objective data of situation awareness and decision quality.

Feasibility and systems definition study for Microwave Multi-Application Payload (MMAP)

NASA Technical Reports Server (NTRS)

Horton, J. B.; Allen, C. C.; Massaro, M. J.; Zemany, J. L.; Murrell, J. W.; Stanhouse, R. W.; Condon, G. P.; Stone, R. F.; Swana, J.; Afifi, M.

1977-01-01

Work completed on three Shuttle/Spacelab experiments is examined: the Adaptive Multibeam Phased Array Antenna (AMPA) Experiment, Electromagnetic Environment Experiment (EEE) and Millimeter Wave Communications Experiment (MWCE). Results included the definition of operating modes, sequence of operation, radii of operation about several ground stations, signal format, foot prints of typical orbits and preliminary definition of ground and user terminals. Conceptual hardware designs, Spacelab interfaces, data handling methods, experiment testing and verification studies were included. The MWCE-MOD I was defined conceptually for a steerable high gain antenna.

Initial Development of a Spatially Separated Speech-in-Noise and Localization Training Program

PubMed Central

Tyler, Richard S.; Witt, Shelley A.; Dunn, Camille C.; Wang, Wenjun

2010-01-01

Objective This article describes the initial development of a novel approach for training hearing-impaired listeners to improve their ability to understand speech in the presence of background noise and to also improve their ability to localize sounds. Design Most people with hearing loss, even those well fit with hearing devices, still experience significant problems understanding speech in noise. Prior research suggests that at least some subjects can experience improved speech understanding with training. However, all training systems that we are aware of have one basic, critical limitation. They do not provide spatial separation of the speech and noise, therefore ignoring the potential benefits of training binaural hearing. In this paper we describe our initial experience with a home-based training system that includes spatially separated speech-in-noise and localization training. Results Throughout the development of this system patient input, training and preliminary pilot data from individuals with bilateral cochlear implants were utilized. Positive feedback from subjective reports indicated that some individuals were engaged in the treatment, and formal testing showed benefit. Feedback and practical issues resulted from the reduction of an eight-loudspeaker to a two-loudspeaker system. Conclusions These preliminary findings suggest we have successfully developed a viable spatial hearing training system that can improve binaural hearing in noise and localization. Applications include, but are not limited to, hearing with hearing aids and cochlear implants. PMID:20701836

Preliminary Experiment of Non-Inductive Plasma Current Startup in SUNIST Spherical Tokamak

NASA Astrophysics Data System (ADS)

He, Yexi; Zhang, Liang; Xie, Lifeng; Tang, Yi; Yang, Xuanzong; Feng, Chunhua; Fu, Hongjun

2006-01-01

The non-inductive plasma current startup is an important motivation in SUNIST spherical tokamak. In the recent experiment, the magnetron microwave system of 100 kW and 2.45 GHz has been used to the ECR plasma current startup. Besides the toroidal field, a vertical field was applied to generate preliminary toroidal plasma current without the action of the central solenoid. As the evidence of plasma current startup with the effect of vertical field drift, the direction of plasma current is changed when the direction of vertical field changes during the ECR plasma current startup discharge. We also observed a maximum plasma current by scanning vertical field in both directions. Additionally, we used electrode discharge to assist the ECR plasma current startup.

Design and implementation of a preprocessing system for a sodium lidar

NASA Technical Reports Server (NTRS)

Voelz, D. G.; Sechrist, C. F., Jr.

1983-01-01

A preprocessing system, designed and constructed for use with the University of Illinois sodium lidar system, was developed to increase the altitude resolution and range of the lidar system and also to decrease the processing burden of the main lidar computer. The preprocessing system hardware and the software required to implement the system are described. Some preliminary results of an airborne sodium lidar experiment conducted with the preprocessing system installed in the sodium lidar are presented.

CELSS experiment model and design concept of gas recycle system

NASA Technical Reports Server (NTRS)

Nitta, K.; Oguchi, M.; Kanda, S.

1986-01-01

In order to prolong the duration of manned missions around the Earth and to expand the human existing region from the Earth to other planets such as a Lunar Base or a manned Mars flight mission, the controlled ecological life support system (CELSS) becomes an essential factor of the future technology to be developed through utilization of space station. The preliminary system engineering and integration efforts regarding CELSS have been carried out by the Japanese CELSS concept study group for clarifying the feasibility of hardware development for Space station experiments and for getting the time phased mission sets after FY 1992. The results of these studies are briefly summarized and the design and utilization methods of a Gas Recycle System for CELSS experiments are discussed.

3RIP Evaluation of the Performance of the Search System Using a Realtime Simulation Technique.

ERIC Educational Resources Information Center

Lofstrom, Mats

This report describes a real-time simulation experiment to evaluate the performance of the search and editing system 3RIP, an interactive system written in the language BLISS on a DEC-10 computer. The test vehicle, preliminary test runs, and capacity test are detailed, and the following conclusions are reported: (1) 3RIP performs well up to the…

Preliminary results of the scientific experiments on the Kosmos-936 biosatellite

NASA Technical Reports Server (NTRS)

1977-01-01

The scientific equipment and experiments on the Kosmos-936 biosatellite are described, including various ground controls and the lab unit for studies at the descent vehicle landing site. Preliminary results are presented of the physiological experiment with rats, biological experiments with drosophila and higher and lower plants, and radiation physics and radiobiology studies for the planning of biological protection on future space flights. The most significant conclusion from the preliminary data is that rats tolerate space flight better with an artificial force of gravity.

A nearshore processes field experiment at Cape Hatteras, North Carolina, U.S.A.

USGS Publications Warehouse

List, Jeffrey H.; Warner, John C.; Thieler, E. Robert; Haas, Kevin; Voulgaris, George; McNinch, Jesse E.; Brodie, Katherine L.; Rosati, Julie D.; Wang, Ping; Roberts, Tiffany M.

2011-01-01

A month-long field experiment focused on the nearshore hydrodynamics of Diamond Shoals adjacent to Cape Hatteras Point, North Carolina, was conducted in February 2010. The objectives of this multi-institutional experiment were to test hypotheses related to Diamond Shoals as a sink in the regional sediment budget and to provide data for evaluating numerical models. The experiment included in-situ instrumentation for measuring waves and currents; a video camera system for measuring surface currents at a nearshore transect; a radar system for measuring regional surface currents over Diamond Shoals and the adjacent coast; a vehicle-based scanning lidar and radar system for mapping beach topography, nearshore wave breaking intensity, bathymetry (through wave celerity inversion), and wave direction; and an amphibious vehicle system for surveying single-beam bathymetry. Preliminary results from wave and current measurements suggest that shoal-building processes were active during the experiment.

ATS-6 - Preliminary results from the 13/18-GHz COMSAT Propagation Experiment

NASA Technical Reports Server (NTRS)

Hyde, G.

1975-01-01

The 13/18-GHz COMSAT Propagation Experiment (CPE) is reviewed, the data acquisition and processing are discussed, and samples of preliminary results are presented. The need for measurements of both hydrometeor-induced attenuation statistics and diversity effectiveness is brought out. The facilitation of the experiment - CPE dual frequency and diversity site location, the CPE ground transmit terminals, the CPE transponder on Applications Technology Satellite-6 (ATS-6), and the CPE receive and data acquisition system - is briefly examined. The on-line preprocessing of the received signal is reviewed, followed by a discussion of the off-line processing of this database to remove signal fluctuations not due to hydrometeors. Finally, samples of the results of first-level analysis of the resultant data for the 18-GHz diversity site near Boston, Mass., and for the dual frequency 13/18-GHz site near Detroit, Mich., are presented and discussed.

Conjugating binary systems for spacecraft thermal control. Appendix C: Aeroassist Flight Experiment Carrier Vehicle preliminary stress analysis

NASA Technical Reports Server (NTRS)

Ingram, J. E.; Murray, T. O.

1989-01-01

An assessment of the static strength of the Aeroassist Flight Experiment (AFE) Carrier Vehicle is presented. The Carrier Vehicle is the structural component which provides the mounting platform for the experiments, on-board computers, batteries, and other black boxes. In addition, the Solid Rocket Motor (SRM), the Thrusters, and the Aerobrake are all attached directly to the Carrier Vehicle. The basic approach in this analysis was to develop a NASTRAN Finite Element Model as a parallel effort to the preliminary design, and to use the internal loads from this model to perform the stress analysis. The NASTRAN method of Inertial Relief was employed. This method involves either specifying a set of CG (center of gravity) accelerations or applying forces at the CG and representing the Carrier Vehicle and all its mounted devices with the proper stiffness and mass properties.

Modular space station Phase B extension preliminary performance specification. Volume 2: Project

NASA Technical Reports Server (NTRS)

1971-01-01

The four systems of the modular space station project are described, and the interfaces between this project and the shuttle project, the tracking and data relay satellite project, and an arbitrarily defined experiment project are defined. The experiment project was synthesized from internal experiments, detached research and application modules, and attached research and application modules to derive a set of interface requirements which will support multiple combinations of these elements expected during the modular space station mission. The modular space station project element defines a 6-man orbital program capable of growth to a 12-man orbital program capability. The modular space station project element specification defines the modular space station system, the premission operations support system, the mission operations support system, and the cargo module system and their interfaces.

INTEGRATED BIOPROCESS SYSTEMS FOR LOW-COST ENVIRONMENTAL REMEDIATION AND SUSTAINABLE BIOFERTILIZER PRODUCTION

EPA Science Inventory

Preliminary techno-economic analysis of these processes will be undertaken, utilizing the literature and including key supporting data and proof-of-principle experiments. The emphasis on low-cost bioreactors and operation greatly enhances the economic feasibility and practica...

A Multi-User Remote Academic Laboratory System

ERIC Educational Resources Information Center

Barrios, Arquimedes; Panche, Stifen; Duque, Mauricio; Grisales, Victor H.; Prieto, Flavio; Villa, Jose L.; Chevrel, Philippe; Canu, Michael

2013-01-01

This article describes the development, implementation and preliminary operation assessment of Multiuser Network Architecture to integrate a number of Remote Academic Laboratories for educational purposes on automatic control. Through the Internet, real processes or physical experiments conducted at the control engineering laboratories of four…

Preliminary Clinical Experience with a Combined Automated Breast Ultrasound and Digital Breast Tomosynthesis System.

PubMed

Larson, Eric D; Lee, Won-Mean; Roubidoux, Marilyn A; Goodsitt, Mitchell M; Lashbrook, Chris; Davis, Cynthia E; Kripfgans, Oliver D; Carson, Paul L

2018-03-01

We analyzed the performance of a mammographically configured, automated breast ultrasound (McABUS) scanner combined with a digital breast tomosynthesis (DBT) system. The GE Invenia ultrasound system was modified for integration with GE DBT systems. Ultrasound and DBT imaging were performed in the same mammographic compression. Our small preliminary study included 13 cases, six of whom had contained invasive cancers. From analysis of these cases, current limitations and corresponding potential improvements of the system were determined. A registration analysis was performed to compare the ease of McABUS to DBT registration for this system with that of two systems designed previously. It was observed that in comparison to data from an earlier study, the McABUS-to-DBT registration alignment errors for both this system and a previously built combined system were smaller than those for a previously built standalone McABUS system. Copyright © 2018 World Federation for Ultrasound in Medicine and Biology. Published by Elsevier Inc. All rights reserved.

Second generation experiments in fault tolerant software

NASA Technical Reports Server (NTRS)

Knight, J. C.

1987-01-01

The purpose of the Multi-Version Software (MVS) experiment is to obtain empirical measurements of the performance of multi-version systems. Twenty version of a program were prepared under reasonably realistic development conditions from the same specifications. The overall structure of the testing environment for the MVS experiment and its status are described. A preliminary version of the control system is described that was implemented for the MVS experiment to allow the experimenter to have control over the details of the testing. The results of an empirical study of error detection using self checks are also presented. The analysis of the checks revealed that there are great differences in the ability of individual programmers to design effective checks.

Data relay system specifications for ERTS image interpretation

NASA Technical Reports Server (NTRS)

Daniel, J. F.

1970-01-01

Experiments with the Data Collection System (DCS) of the Earth Resources Technology Satellites (ERTS) have been developed to stress ERTS applications in the Earth Resources Observation Systems (EROS) Program. Active pursuit of this policy has resulted in the design of eight specific experiments requiring a total of 98 DCS ground-data platforms. Of these eight experiments, six are intended to make use of DCS data as an aid in image interpretation, while two make use of the capability to relay data from remote locations. Preliminary discussions regarding additional experiments indicate a need for at least 150 DCS platforms within the EROS Program for ERTS experimentation. Results from the experiments will be used to assess the DCS suitability for satellites providing on-line, real-time, data relay capability. The rationale of the total DCS network of ground platforms and the relationship of each experiment to that rationale are discussed.

Safety Performance of Airborne Separation: Preliminary Baseline Testing

NASA Technical Reports Server (NTRS)

Consiglio, Maria C.; Hoadley, Sherwood T.; Wing, David J.; Baxley, Brian T.

2007-01-01

The Safety Performance of Airborne Separation (SPAS) study is a suite of Monte Carlo simulation experiments designed to analyze and quantify safety behavior of airborne separation. This paper presents results of preliminary baseline testing. The preliminary baseline scenario is designed to be very challenging, consisting of randomized routes in generic high-density airspace in which all aircraft are constrained to the same flight level. Sustained traffic density is varied from approximately 3 to 15 aircraft per 10,000 square miles, approximating up to about 5 times today s traffic density in a typical sector. Research at high traffic densities and at multiple flight levels are planned within the next two years. Basic safety metrics for aircraft separation are collected and analyzed. During the progression of experiments, various errors, uncertainties, delays, and other variables potentially impacting system safety will be incrementally introduced to analyze the effect on safety of the individual factors as well as their interaction and collective effect. In this paper we report the results of the first experiment that addresses the preliminary baseline condition tested over a range of traffic densities. Early results at five times the typical traffic density in today s NAS indicate that, under the assumptions of this study, airborne separation can be safely performed. In addition, we report on initial observations from an exploration of four additional factors tested at a single traffic density: broadcast surveillance signal interference, extent of intent sharing, pilot delay, and wind prediction error.

Analyses of space environment effects on active fiber optic links orbited aboard the LDEF

NASA Technical Reports Server (NTRS)

Taylor, Edward W.; Monarski, T. W.; Berry, J. N.; Sanchez, A. D.; Padden, R. J.; Chapman, S. P.

1993-01-01

The results of the 'Preliminary Analysis of WL Experiment no. 701, Space Environment Effects on Operating Fiber Optic Systems,' is correlated with space simulated post retrieval terrestrial studies performed on the M0004 experiment. Temperature cycling measurements were performed on the active optical data links for the purpose of assessing link signal to noise ratio and bit error rate performance some 69 months following the experiment deployment in low Earth orbit. The early results indicate a high correlation between pre-orbit, orbit, and post-orbit functionality of the first known and longest space demonstration of operating fiber optic systems.

Molecular-beam gas-sampling system

NASA Technical Reports Server (NTRS)

Young, W. S.; Knuth, E. L.

1972-01-01

A molecular beam mass spectrometer system for rocket motor combustion chamber sampling is described. The history of the sampling system is reviewed. The problems associated with rocket motor combustion chamber sampling are reported. Several design equations are presented. The results of the experiments include the effects of cooling water flow rates, the optimum separation gap between the end plate and sampling nozzle, and preliminary data on compositions in a rocket motor combustion chamber.

Performance of OVERFLOW-D Applications based on Hybrid and MPI Paradigms on IBM Power4 System

NASA Technical Reports Server (NTRS)

Djomehri, M. Jahed; Biegel, Bryan (Technical Monitor)

2002-01-01

This report briefly discusses our preliminary performance experiments with parallel versions of OVERFLOW-D applications. These applications are based on MPI and hybrid paradigms on the IBM Power4 system here at the NAS Division. This work is part of an effort to determine the suitability of the system and its parallel libraries (MPI/OpenMP) for specific scientific computing objectives.

Science Support Room Operations During Desert RATS 2009

NASA Technical Reports Server (NTRS)

Lofgren, G. E.; Horz, F.; Bell, M. S.; Cohen, B. A.; Eppler,D. B.; Evans, C. a.; Hodges, K. V.; Hynek, B. M.; Gruener, J. E.; Kring, D. A.;

Ageing under mechanical stress: first experiments for a silver based multilayer mirror

NASA Astrophysics Data System (ADS)

Lalo, Arnaud; Ravel, Guillaume; Ignat, Michel; Cousin, Bernard; Swain, Michael V.

2017-11-01

Improving materials and devices reliability is a major concern to the spatial industry. Results are reported for satellite mirrors-like specimens consisting in oxide-protected metal systems. Optical coatings were deposited by electron beam evaporation. Mechanical stress fields in multi-layered materials play an important role. The stress state can have far-reaching implications both in kinetics and thermodynamics. Therefore an integrated apparatus with four-point bending equipment was designed. The technique allowed us to exert stress into a film or a system of films on a substrate concurrently with thermal treatment. In order to achieve the first tests performed with the help of the apparatus, various preliminary characterizations were required. The article reports the preliminary micro-mechanical testing of the materials (ultra micro-indentation to evaluate the elastic modulus of the samples materials and wafer curvature technique to determine the specimen residual stress) and the first ageing experiment. Experimental evidence of accelerated ageing under stress is successfully reported.

Investigation of the reaction d + d → {sup 2}He + {sup 2}n at the deuteron energy of 15 MeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konobeevski, E. S., E-mail: konobeev@inr.ru; Zuyev, S. V.; Kasparov, A. A.

An experimental setup for studying the reaction d + d → {sup 2}He + {sup 2}n is described, and the first preliminary results of measurements at a deuteron energy of 15 MeV are presented. The experiment was aimed at determining the energies of quasibound singlet states of two-nucleon systems (nn and pp), these energies being important features of nucleon–nucleon (NN) interaction. The measurements in question were performed at a deuteron beamfrom the U-120 cyclotron of the Skobeltsyn Institute ofNuclear Physics (Moscow State University). Two protons and one of the neutrons fromthe breakup of the dineutron system were detected in themore » experiment. A simulation of the reaction in question and preliminary experimental results reveal the possibility of determining the energy of quasibound singlet states on the basis of the form of the energy spectra of particles originating from their breakup.« less

Synthesis, bioactivity and preliminary biocompatibility studies of glasses in the system CaO-MgO-SiO2-Na2O-P2O5-CaF2.

PubMed

Tulyaganov, D U; Agathopoulos, S; Valerio, P; Balamurugan, A; Saranti, A; Karakassides, M A; Ferreira, J M F

2011-02-01

New compositions of bioactive glasses are proposed in the CaO-MgO-SiO(2)-Na(2)O-P(2)O(5)-CaF(2) system. Mineralization tests with immersion of the investigated glasses in simulated body fluid (SBF) at 37°C showed that the glasses favour the surface formation of hydroxyapatite (HA) from the early stages of the experiments. In the case of daily renewable SBF, monetite (CaHPO(4)) formation competed with the formation of HA. The influence of structural features of the glasses on their mineralization (bioactivity) performance is discussed. Preliminary in vitro experiments with osteoblasts' cell-cultures showed that the glasses are biocompatible and there is no evidence of toxicity. Sintering and devitrification studies of glass powder compacts were also performed. Glass-ceramics with attractive properties were obtained after heat treatment of the glasses at relatively low temperatures (up to 850°C).

Investigation of helicon ion source extraction systems.

PubMed

Mordyk, S; Miroshnichenko, V; Shulha, D; Storizhko, V

2008-02-01

Various versions of an extraction system for a helicon ion source have been investigated in high plasma density (>10(12) cm(-3)) modes. The measurements of the plasma density were carried out with a microwave interferometer. Experiments were performed with hydrogen and helium gases. The preliminary results indicate that specially designed extractors are very promising for improving ion beam paraxial brightness.

Markov Chains For Testing Redundant Software

NASA Technical Reports Server (NTRS)

White, Allan L.; Sjogren, Jon A.

1990-01-01

Preliminary design developed for validation experiment that addresses problems unique to assuring extremely high quality of multiple-version programs in process-control software. Approach takes into account inertia of controlled system in sense it takes more than one failure of control program to cause controlled system to fail. Verification procedure consists of two steps: experimentation (numerical simulation) and computation, with Markov model for each step.

Development of a near-infrared spectroscopic system for monitoring urine glucose level for the use of long-term home healthcare

NASA Astrophysics Data System (ADS)

Tanaka, Shinobu; Hayakawa, Yuuto; Ogawa, Mitsuhiro; Yamakoshi, Ken-ichi

2010-08-01

We have been developing a new technique for measuring urine glucose concentration using near infrared spectroscopy (NIRS) in conjunction with the Partial Least Square (PLS) method. In the previous study, we reported some results of preliminary experiments for assessing feasibility of this method using a FT-IR spectrometer. In this study, considering practicability of the system, a flow-through cell with the optical path length of 10 mm was newly introduced. Accuracy of the system was verified by the preliminary experiments using urine samples. From the results obtained, it was clearly demonstrated that the present method had a capability of predicting individual urine glucose level with reasonable accuracy (the minimum value of standard error of prediction: SEP = 22.3 mg/dl) and appeared to be a useful means for long-term home health care. However, mean value of SEP obtained by the urine samples from ten subjects was not satisfactorily low (53.7 mg/dl). For improving the accuracy, (1) mechanical stability of the optical system should be improved, (2) the method for normalizing the spectrum should be reconsidered, and (3) the number of subject should be increased.

A mobile telephone-based SMS and internet survey system for self-assessment in Australian anaesthesia: experience of a single practitioner.

PubMed

Belavy, D

2014-11-01

Self-assessment and audit in anaesthesia require a systematic approach to postoperative data collection. The increasing prevalence of mobile internet technology offers a new data collection method for anaesthetists. In this paper, a system for mobile internet data collection is described and the preliminary experience with its use is presented. The system was developed by the author and combined an open source survey application and a short message service (SMS) gateway to send SMS messages to patients after their anaesthesia and surgery. The messages requested patients to complete an online Quality of Recovery survey questionnaire if they had a smartphone. The results were immediately available. A preliminary survey of consenting patients with available mobile telephone numbers in a private practice was undertaken by the author. A total of 123 procedures were eligible for follow-up and survey requests were sent to 94 patients. Sixty-five surveys were completed. This represents 69% of surveys requested, demonstrating that mobile phone technology can be used to provide significant amounts of data for quality assurance. However, the implementation of a mobile internet data collection system requires consideration of privacy principles, security and ethical handling of data.

Augmented Reality for Maintenance and Repair (ARMAR)

DTIC Science & Technology

2007-08-01

800×600 resolution monocular display, whose small size and lack of an opaque “ frame ”, provides the closest experience to an eyeglass form factor, and...Alternatively, fiducials could be mounted on lightweight rigid frames that are attached to predetermined points on the maintained system. Figure...stereo at 800×600 resolution, thirty frames per second, creating a compelling experience of an augmented workspace. Based on our preliminary

Decision-Making in Flight with Different Convective Weather Information Sources: Preliminary Results from the Langley CoWS Experiment (COnvective Weather Sources)

NASA Technical Reports Server (NTRS)

Chamberlain, Jim; Latorella, Kara

2003-01-01

This viewgraph presentation provides information on an airborne experiment designed to test the decision making of pilots receiving different sources of meteorological data. The presentation covers the equipment used in the COnvective Weather Sources (CoWS) Experiment), including the information system and display devices available to some of the subjects. It also describes the experiment, which featured teams of general aviation pilots, who were onboard but did not actually fly the aircraft used in the experiment. The presentation includes the results of a survey of the subjects' confidence.

Evaluation of a decision support system for pressure ulcer prevention and management: preliminary findings.

PubMed

Zielstorff, R D; Estey, G; Vickery, A; Hamilton, G; Fitzmaurice, J B; Barnett, G O

1997-01-01

A decision support system for prevention and management of pressure ulcers was developed based on AHCPR guidelines and other sources. The system was implemented for 21 weeks on a 20-bed clinical care unit. Fifteen nurses on that unit volunteered as subjects of the intervention to see whether use of the system would have a positive effect on their knowledge about pressure ulcers and on their decision-making skills related to this topic. A similar care unit was used as a control. In addition, the system was evaluated by experts for its instructional adequacy, and by end users for their satisfaction with the system. Preliminary results show no effect on knowledge about pressure ulcers and no effect on clinical decision making skills. The system was rated positively for instructional adequacy, and positively for user satisfaction. User interviews related to satisfaction supplemented the quantitative findings. A discussion of the issues of conducting experiments like this in today's clinical environment is included.

Space station definitions, design, and development. Task 5: Multiple arm telerobot coordination and control: Manipulator design methodology

NASA Technical Reports Server (NTRS)

Stoughton, R. M.

1990-01-01

A proposed methodology applicable to the design of manipulator systems is described. The current design process is especially weak in the preliminary design phase, since there is no accepted measure to be used in trading off different options available for the various subsystems. The design process described uses Cartesian End-Effector Impedance as a measure of performance for the system. Having this measure of performance, it is shown how it may be used to determine the trade-offs necessary to the preliminary design phase. The design process involves three main parts: (1) determination of desired system performance in terms of End-Effector Impedance; (2) trade-off design options to achieve this desired performance; and (3) verification of system performance through laboratory testing. The design process is developed using numerous examples and experiments to demonstrate the feasability of this approach to manipulator design.

Solar Stirling power generation - Systems analysis and preliminary tests

NASA Technical Reports Server (NTRS)

Selcuk, M. K.; Wu, Y.-C.; Moynihan, P. I.; Day, F. D., III

1977-01-01

The feasibility of an electric power generation system utilizing a sun-tracking parabolic concentrator and a Stirling engine/linear alternator is being evaluated. Performance predictions and cost analysis of a proposed large distributed system are discussed. Design details and preliminary test results are presented for a 9.5 ft diameter parabolic dish at the Jet Propulsion Laboratory (Caltech) Table Mountain Test Facility. Low temperature calorimetric measurements were conducted to evaluate the concentrator performance, and a helium flow system is being used to test the solar receiver at anticipated working fluid temperatures (up to 650 or 1200 C) to evaluate the receiver thermal performance. The receiver body is designed to adapt to a free-piston Stirling engine which powers a linear alternator assembly for direct electric power generation. During the next phase of the program, experiments with an engine and receiver integrated into the concentrator assembly are planned.

Detailed design package for design of a video system providing optimal visual information for controlling payload and experiment operations with television

NASA Technical Reports Server (NTRS)

1975-01-01

A detailed description of a video system for controlling space shuttle payloads and experiments is presented in the preliminary design review and critical design review, first and second engineering design reports respectively, and in the final report submitted jointly with the design package. The material contained in the four subsequent sections of the package contains system descriptions, design data, and specifications for the recommended 2-view system. Section 2 contains diagrams relating to the simulation test configuration of the 2-view system. Section 3 contains descriptions and drawings of the deliverable breadboard equipment. A description of the recommended system is contained in Section 4 with equipment specifications in Section 5.

STEP Experiment Requirements

NASA Technical Reports Server (NTRS)

Brumfield, M. L. (Compiler)

1984-01-01

A plan to develop a space technology experiments platform (STEP) was examined. NASA Langley Research Center held a STEP Experiment Requirements Workshop on June 29 and 30 and July 1, 1983, at which experiment proposers were invited to present more detailed information on their experiment concept and requirements. A feasibility and preliminary definition study was conducted and the preliminary definition of STEP capabilities and experiment concepts and expected requirements for support services are presented. The preliminary definition of STEP capabilities based on detailed review of potential experiment requirements is investigated. Topics discussed include: Shuttle on-orbit dynamics; effects of the space environment on damping materials; erectable beam experiment; technology for development of very large solar array deployers; thermal energy management process experiment; photovoltaic concentrater pointing dynamics and plasma interactions; vibration isolation technology; flight tests of a synthetic aperture radar antenna with use of STEP.

Survey Instruments to Assess Patient Experiences With Access and Coordination Across Health Care Settings: Available and Needed Measures.

PubMed

Quinn, Martha; Robinson, Claire; Forman, Jane; Krein, Sarah L; Rosland, Ann-Marie

2017-07-01

Improving access can increase the providers a patient sees, and cause coordination challenges. For initiatives that increase care across health care settings, measuring patient experiences with access and care coordination will be crucial. Map existing survey measures of patient experiences with access and care coordination expected to be relevant to patients accessing care across settings. Preliminarily examine whether aspects of access and care coordination important to patients are represented by existing measures. Structured literature review of domains and existing survey measures related to access and care coordination across settings. Survey measures, and preliminary themes from semistructured interviews of 10 patients offered VA-purchased Community Care, were mapped to identified domains. We identified 31 existing survey instruments with 279 items representing 6 access and 5 care coordination domains relevant to cross-system care. Domains frequently assessed by existing measures included follow-up coordination, primary care access, cross-setting coordination, and continuity. Preliminary issues identified in interviews, but not commonly assessed by existing measures included: (1) acceptability of distance to care site given patient's clinical situation; (2) burden on patients to access and coordinate care and billing; (3) provider familiarity with Veteran culture and VA processes. Existing survey instruments assess many aspects of patient experiences with access and care coordination in cross-system care. Systems assessing cross-system care should consider whether patient surveys accurately reflect the level of patients' concerns with burden to access and coordinate care, and adequately reflect the impact of clinical severity and cultural familiarity on patient preferences.

A rocket-borne microprocessor-based experiment for investigation of energetic particles in the D and E regions

NASA Technical Reports Server (NTRS)

Braswell, F. M.

1981-01-01

An energetic experiment using the Z80 family of microcomputer components is described. Data collected from the experiment allowed fast and efficient postprocessing, yielding both energy-spectrum and pitch-angle distribution of energetic particles in the D and E regions. Advanced microprocessor system architecture and software concepts were used in the design to cope with the large amount of data being processed. This required the Z80 system to operate at over 80% of its total capacity. The microprocessor system was included in the payloads of three rockets launched during the Energy Budget Campaign at ESRANGE, Kiruna, Sweden in November 1980. Based on preliminary examination of the data, the performance of the experiment was satisfactory and good data were obtained on the energy spectrum and pitch-angle distribution of the particles.

Manned orbital systems concepts study. Book 2: Requirements for extended-duration missions

NASA Technical Reports Server (NTRS)

1975-01-01

In order to provide essential data needed in long-range program planning, the Manned Orbital Systems Concepts (MOSC) study attempted to define, evaluate, and compare concepts for manned orbital systems that provide extended experiment mission capabilities in space, flexibility of operation, and growth potential. Specific areas discussed include roles and requirements for man in future space missions, requirements for extended capability, mission/payload concepts, and preliminary design and operational requirements.

PANDA Muon System Prototype

NASA Astrophysics Data System (ADS)

Abazov, Victor; Alexeev, Gennady; Alexeev, Maxim; Frolov, Vladimir; Golovanov, Georgy; Kutuzov, Sergey; Piskun, Alexei; Samartsev, Alexander; Tokmenin, Valeri; Verkheev, Alexander; Vertogradov, Leonid; Zhuravlev, Nikolai

2018-04-01

The PANDA Experiment will be one of the key experiments at the Facility for Antiproton and Ion Research (FAIR) which is under construction now in the territory of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt, Germany. PANDA is aimed to study hadron spectroscopy and various topics of the weak and strong forces. Muon System is chosen as the most suitable technology for detecting the muons. The Prototype of the PANDA Muon System is installed on the test beam line T9 at the Proton Synchrotron (PS) at CERN. Status of the PANDA Muon System prototype is presented with few preliminary results.

Methodology and preliminary results of evaluating stem displacement and assessing root system architecture of longleaf pine saplings

Treesearch

Shi-Jean S. Sung; Daniel J. Leduc; James D. Haywood; Thomas L. Eberhardt; Mary Anne Sword Sayer; Stanley J. Zarnoch

2012-01-01

A field experiment of the effects of container cavity size and root pruning type on longleaf pine was established in November, 2004, in central Louisiana. Sapling stems were first observed to be leaning after hurricane Gustav (September, 2008) and again in August, 2009. To examine the relationship between stem displacement and root system architecture, a stem-displaced...

First Results of the Regional Earthquake Likelihood Models Experiment

USGS Publications Warehouse

Schorlemmer, D.; Zechar, J.D.; Werner, M.J.; Field, E.H.; Jackson, D.D.; Jordan, T.H.

2010-01-01

The ability to successfully predict the future behavior of a system is a strong indication that the system is well understood. Certainly many details of the earthquake system remain obscure, but several hypotheses related to earthquake occurrence and seismic hazard have been proffered, and predicting earthquake behavior is a worthy goal and demanded by society. Along these lines, one of the primary objectives of the Regional Earthquake Likelihood Models (RELM) working group was to formalize earthquake occurrence hypotheses in the form of prospective earthquake rate forecasts in California. RELM members, working in small research groups, developed more than a dozen 5-year forecasts; they also outlined a performance evaluation method and provided a conceptual description of a Testing Center in which to perform predictability experiments. Subsequently, researchers working within the Collaboratory for the Study of Earthquake Predictability (CSEP) have begun implementing Testing Centers in different locations worldwide, and the RELM predictability experiment-a truly prospective earthquake prediction effort-is underway within the U. S. branch of CSEP. The experiment, designed to compare time-invariant 5-year earthquake rate forecasts, is now approximately halfway to its completion. In this paper, we describe the models under evaluation and present, for the first time, preliminary results of this unique experiment. While these results are preliminary-the forecasts were meant for an application of 5 years-we find interesting results: most of the models are consistent with the observation and one model forecasts the distribution of earthquakes best. We discuss the observed sample of target earthquakes in the context of historical seismicity within the testing region, highlight potential pitfalls of the current tests, and suggest plans for future revisions to experiments such as this one. ?? 2010 The Author(s).

Ocean Thermal Energy Conversion power system development. Phase I. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-12-04

This report covers the conceptual and preliminary design of closed-cycle, ammonia, ocean thermal energy conversion power plants by Westinghouse Electric Corporation. Preliminary designs for evaporator and condenser test articles (0.13 MWe size) and a 10 MWe modular experiment power system are described. Conceptual designs for 50 MWe power systems, and 100 MWe power plants are also descirbed. Design and cost algorithms were developed, and an optimized power system design at the 50 MWe size was completed. This design was modeled very closely in the test articles and in the 10 MWe Modular Application. Major component and auxiliary system design, materials,more » biofouling, control response, availability, safety and cost aspects are developed with the greatest emphasis on the 10 MWe Modular Application Power System. It is concluded that all power plant subsystems are state-of-practice and require design verification only, rather than continued research. A complete test program, which verifies the mechanical reliability as well as thermal performance, is recommended and described.« less

Field Performance of an Indica x Tropical Japonica Rice Mapping Population under AWD Stress

USDA-ARS?s Scientific Manuscript database

Alternating-wetting-drying (AWD) is an emerging rice irrigation management system that has the potential ability to reduce both irrigation water use and emissions of the greenhouse gas, methane. Based on preliminary experiments, 15 (F10) recombinant inbred lines (RILs) showing diversity for root an...

Noise control for rapid transit cars on elevated structures : preliminary investigation of vehicle skirts, undercar absorption, and noise barriers

DOT National Transportation Integrated Search

1980-04-01

In the report, procedures to reduce the propulsion system noise of urban rail transit vehicles on elevated structures are studied. Experiments in a laboratory use a scale model transit vehicle to evaluate the acoustical effectiveness of noise barrier...

Preliminary Examination of Sahara 99555: Mineralogy and Experimental Studies of a New Angrite

NASA Technical Reports Server (NTRS)

Mikouchi, T.; McKay, G.; Le, L.; Mittlefehldt, D. W.

2000-01-01

A 2710 g meteorite, Sahara 99555 (Sah99), was recently recovered from the Sahara and reported to be the 5th angrite. It is the largest angrite ever found and may offer useful information to better understand the unusual petrogeneses of this rare achondrite group. It may also allow us to examine the chronological record of igneous activity in the very early solar system. We obtained a 2.6 g chip of Sah99 and here present a preliminary report of its petrology and mineralogy in conjunction with a crystallization experiment on an analogue composition.

One vendor's experience: preliminary development of a reminder system based on the Arden Syntax.

PubMed

Spates, R P; Aller, K C

1994-09-01

This article reviews the efforts of HBO & Company in the production of a first phase clinical alerting system based on the Arden Syntax. The alerting system was integrated with a clinical data repository and clinical workstation to process returning laboratory results. Investigations with expert systems resulted in a C language alerting system. GUI prototyping of an authoring environment led to a Smalltalk language authoring system. Future development is expected to broaden the system scope and address the evolution of the Arden Syntax.

Flocculation and aggregation in a microgravity environment (FAME)

NASA Technical Reports Server (NTRS)

Ansari, Rafat R.; Dhadwal, Harbans S.; Suh, Kwang I.

1994-01-01

An experiment to study flocculation phenomena in the constrained microgravity environment of a space shuttle or space station is described. The small size and light weight experiment easily fits in a Spacelab Glovebox. Using an integrated fiber optic dynamic light scattering (DLS) system we obtain high precision particle size measurements from dispersions of colloidal particles within seconds, needs no onboard optical alignment, no index matching fluid, and offers sample mixing and shear melting capabilities to study aggregation (flocculation and coagulation) phenomena under both quiescent and controlled agitation conditions. The experimental system can easily be adapted for other microgravity experiments requiring the use of DLS. Preliminary results of ground-based study are reported.

Avionics test bed development plan

NASA Technical Reports Server (NTRS)

Harris, L. H.; Parks, J. M.; Murdock, C. R.

1981-01-01

A development plan for a proposed avionics test bed facility for the early investigation and evaluation of new concepts for the control of large space structures, orbiter attached flex body experiments, and orbiter enhancements is presented. A distributed data processing facility that utilizes the current laboratory resources for the test bed development is outlined. Future studies required for implementation, the management system for project control, and the baseline system configuration are defined. A background analysis of the specific hardware system for the preliminary baseline avionics test bed system is included.

Statistical characterization of fluctuations of a laser beam transmitted through a random air-water interface: new results from a laboratory experiment

NASA Astrophysics Data System (ADS)

Majumdar, Arun K.; Land, Phillip; Siegenthaler, John

2014-10-01

New results for characterizing laser intensity fluctuation statistics of a laser beam transmitted through a random air-water interface relevant to underwater communications are presented. A laboratory watertank experiment is described to investigate the beam wandering effects of the transmitted beam. Preliminary results from the experiment provide information about histograms of the probability density functions of intensity fluctuations for different wind speeds measured by a CMOS camera for the transmitted beam. Angular displacements of the centroids of the fluctuating laser beam generates the beam wander effects. This research develops a probabilistic model for optical propagation at the random air-water interface for a transmission case under different wind speed conditions. Preliminary results for bit-error-rate (BER) estimates as a function of fade margin for an on-off keying (OOK) optical communication through the air-water interface are presented for a communication system where a random air-water interface is a part of the communication channel.

Front-end electronics for the LZ experiment

NASA Astrophysics Data System (ADS)

Morad, James; LZ Collaboration

2016-03-01

LZ is a second generation direct dark matter detection experiment with 5.6 tonnes of liquid xenon active target, which will be instrumented as a two-phase time projection chamber (TPC). The peripheral xenon outside the active TPC (``skin'') will also be instrumented. In addition, there will be a liquid scintillator based outer veto surrounding the main cryostat. All of these systems will be read out using photomultiplier tubes. I will present the designs for front-end electronics for all these systems, which have been optimized for shaping times, gains, and low noise. Preliminary results from prototype boards will also be presented.

High-Temperature Controlled Redox Crystallization Studies

NASA Technical Reports Server (NTRS)

Williams, R. J.

1985-01-01

The crystallization of silicates containing redox sensitive ions (e.g., Fe, Ti, Ce) must be performed under controlled and known redox conditions in order to obtain the maximum scientific benefit from experimental study. Furthermore, many compositions crystallize dense phases which settle during ground-based experiments. This settling influences the texture and chemical evolution of the crystallizing system. The purpose of this investigation is to develop a test system in which controlled redox experiments can be performed in the microgravity environment. The system will use solid ceramic oxygen electrolyte cells for control, measurements, and production of the required redox conditions. A preliminary design for a prototype is developed, the electrolyte and furnace tested, and a tentative protocol for experiment developed. The control parameter is to be established and a laboratory prototype built.

Development of a liquid lithium thin film for use as a heavy ion beam stripper.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Momozaki, Y.; Nolen, J.; Reed, C.

2009-04-01

A series of experiments was performed to investigate the feasibility of a liquid lithium thin film for a charge stripper in a high-power heavy ion linac. Various preliminary experiments using simulants were first conducted to determine the film formation scheme, to investigate the film stability, and to obtain the design parameters for a liquid lithium thin film system. Based on the results from these preliminary studies, a prototypical, high pressure liquid lithium system was constructed to demonstrate liquid lithium thin film formation. This system was capable of driving liquid lithium at {approx}< 300 C and up to 13.9 MPa (2000more » psig) through a nozzle opening as large as 1 mm (40 mil) in diameter. This drive pressure corresponds to a Li velocity of >200 m/s. A thin lithium film of 9 mm in width at velocity of {approx}58 m/s was produced. Its thickness was estimated to be roughly {approx}< 13 {micro}m. High vacuum was maintained in the area of the film. This type of liquid metal thin film may also be used in other high power beam applications such as for intense X-ray or neutron sources.« less

The ArDM experiment

DOE PAGES

Harańczyk, M.; Amsler, C.; Badertscher, A.; ...

2010-08-24

The aim of the ArDM project is the development and operation of a one ton double-phase liquid argon detector for direct Dark Matter searches. The detector measures both the scintillation light and the ionization charge from ionizing radiation using two independent readout systems. This paper briefly describes the detector concept and presents preliminary results from the ArDM R & D program, including a 3 l prototype developed to test the charge readout system.

In Vivo Determination of the Complex Elastic Moduli of Cetacean Head Tissue

DTIC Science & Technology

2014-09-30

testing on Navy dolphins and stranded animals, for which permits and approvals have been obtained. 3 WORK COMPLETED System Design A prototype...chosen for the prototype system’s focal length. This would allow examination of brain tissue in a typical adult bottlenose dolphin , which is the...those observed in preliminary in vivo experiments (conducted under a separate effort) on two bottlenose dolphins and one beluga whale. System

The cardiovascular response to the AGS

NASA Technical Reports Server (NTRS)

Cardus, David; Mctaggart, Wesley G.

1993-01-01

This paper reports the preliminary results of experiments on human subjects conducted to study the cardiovascular response to various g-levels and exposure times using an artificial gravity simulator (AGS). The AGS is a short arm centrifuge consisting of a turntable, a traction system, a platform and four beds. Data collection hardware is part of the communication system. The AGS provides a steep acceleration gradient in subjects in the supine position.

Preliminary experiments on dynamic biology of micro-organisms to avoid any specific full-blown syndrome on humans

NASA Astrophysics Data System (ADS)

Meer, Sneer

2002-06-01

The aim of this paper is to apply an efficient system to detect, identify and quicken suppression of any dangerous micro-organism which threatens the health of the human body in any form. It is well known that some specimens of this kind of possess a specific energy related to their speed of division, toxin emissions and high-powered interaction with human and animal cells which have the capacity to provide certain deadly full-blown syndromes. Many problems relating to the above-mentioned properties have not been clarified to date, and it is vital to find a rapid and valid reply as soon as possible. Inter-disciplinary sciences directed us to start some experiments to solve such problems, considering that the human body is dotted with a multiple interactive system of energy release, a fact which can explain the source of the micro-organism's energy also, for their necessity to manifest their deadly pathology. From practical preliminary experiments with some micro-mechanical systems using light-microscopy, connected to video TV Recorder System, one obtains optical enlarged TV images of certain processes which indicated the right way towards our crucial target; ie: the preparation of safe vaccines and safe medicines. This will constitute a basic system to a void deadly manifestations of dangerous micro-organisms and/or even regular infections on earth and in space, a system which will probably be applied at the ISS Space Station and other future actions in space in long and very long flights. We look forward to applying this system of dynamic biology towards preparation of a real and valid vaccine(s) against HIV virus on AIDS diseases.

Beyond Watches and Chocolate-Global Mental Health Elective in Switzerland.

PubMed

Schneeberger, Andres R; Weiss, Andrea; von Blumenthal, Suzanne; Lang, Undine E; Huber, Christian G; Schwartz, Bruce J

2016-08-01

Despite increasing interest in global mental health training opportunities, only a few psychiatry residency programs offer global mental health training experiences in developing countries and even fewer programs offer it in other first-world countries. The authors developed a global mental health elective giving US psychiatry residents the opportunity to visit Switzerland to study and experience the mental health care system in this European country. This elective focuses on four major learning objectives: (1) the system of training and curriculum of postgraduate psychiatry education in Switzerland, (2) clinical and organizational aspects of Swiss mental health, (3) administrative aspects of Swiss mental health care delivery, and (4) scholarly activity. This program was uniquely tailored for psychiatry residents. The preliminary experiences with US psychiatry residents show that they value this learning experience, the opportunity to access a different mental health care system, as well as the potential to build international connections with peers.

Corrosion in MDEA sour gas treating plants: Correlation between laboratory testing and field experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bich, N.N.; Vacha, F.; Schubert, R.

1996-08-01

Corrosion in MDEA sour gas treating systems operating in severely loaded conditions is investigated using both laboratory data and actual gas plant experience. Effects of acid gas loading, flow turbulence, solution quality, temperature, etc. on corrosion are being studied. Preliminary results indicated severe corrosion of several mm/y would occur if acid gas loading, circulation rate and level of suspended solids are all high. A mitigation strategy based on operating envelopes is formulated.

Pattern Laser Annealing by a Pulsed Laser

NASA Astrophysics Data System (ADS)

Komiya, Yoshio; Hoh, Koichiro; Murakami, Koichi; Takahashi, Tetsuo; Tarui, Yasuo

1981-10-01

Preliminary experiments with contact-type pattern laser annealing were made for local polycrystallization of a-Si, local evaporation of a-Si and local formation of Ni-Si alloy. These experiments showed that the mask patterns can be replicated as annealed regions with a resolution of a few microns on substrates. To overcome shortcomings due to the contact type pattern annealing, a projection type reduction pattern laser annealing system is proposed for resistless low temperature pattern forming processes.

LDEF: 69 Months in Space. Third Post-Retrieval Symposium, part 3

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1995-01-01

This volume is a compilation of papers presented at the Third Long Duration Exposure Facility (LDEF) Post-Retrieval Symposium. The papers represent the data analysis of the 57 experiments flown on the LDEF. The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, micrometeoroid, etc.), electronics, optics, and life science. In addition, papers on preliminary data analysis of EURECA, EOIM-3, and other spacecraft are included.

The low-order wavefront control system for the PICTURE-C mission: preliminary testbed results from the Shack-Hartmann sensor

NASA Astrophysics Data System (ADS)

Howe, Glenn A.; Mendillo, Christopher B.; Hewawasam, Kuravi; Martel, Jason; Finn, Susanna C.; Cook, Timothy A.; Chakrabarti, Supriya

2017-09-01

The Planetary Imaging Concept Testbed Using a Recoverable Experiment - Coronagraph (PICTURE-C) mission will directly image debris disks and exozodiacal dust around three nearby stars from a high-altitude balloon using a vector vortex coronagraph. We present experimental results of the PICTURE-C low-order wavefront control (LOWFC) system utilizing a Shack-Hartmann (SH) sensor in an instrument testbed. The SH sensor drives both the alignment of the telescope secondary mirror using a 6-axis Hexapod and a surface parallel array deformable mirror to remove residual low-order aberrations. The sensor design and actuator calibration methods are discussed and the preliminary LOWFC closed-loop performance is shown to stabilize a reference wavefront to an RMS error of 0.30 +/- 0.29 nm.

Preliminary Results of NASA's First Autonomous Formation Flying Experiment: Earth Observing-1 (EO-1)

NASA Technical Reports Server (NTRS)

Folta, David; Hawkins, Albin

2001-01-01

NASA's first autonomous formation flying mission is completing a primary goal of demonstrating an advanced technology called enhanced formation flying. To enable this technology, the Guidance, Navigation, and Control center at the Goddard Space Flight Center has implemented an autonomous universal three-axis formation flying algorithm in executive flight code onboard the New Millennium Program's (NMP) Earth Observing-1 (EO-1) spacecraft. This paper describes the mathematical background of the autonomous formation flying algorithm and the onboard design and presents the preliminary validation results of this unique system. Results from functionality assessment and autonomous maneuver control are presented as comparisons between the onboard EO-1 operational autonomous control system called AutoCon(tm), its ground-based predecessor, and a stand-alone algorithm.

Head-Up Auditory Displays for Traffic Collision Avoidance System Advisories: A Preliminary Investigation

NASA Technical Reports Server (NTRS)

Begault, Durand R.

1993-01-01

The advantage of a head-up auditory display was evaluated in a preliminary experiment designed to measure and compare the acquisition time for capturing visual targets under two auditory conditions: standard one-earpiece presentation and two-earpiece three-dimensional (3D) audio presentation. Twelve commercial airline crews were tested under full mission simulation conditions at the NASA-Ames Man-Vehicle Systems Research Facility advanced concepts flight simulator. Scenario software generated visual targets corresponding to aircraft that would activate a traffic collision avoidance system (TCAS) aural advisory; the spatial auditory position was linked to the visual position with 3D audio presentation. Results showed that crew members using a 3D auditory display acquired targets approximately 2.2 s faster than did crew members who used one-earpiece head- sets, but there was no significant difference in the number of targets acquired.

Preliminary analysis of remote infrared imagery of shuttle during entry: An aerothermodynamic flight experiment

NASA Technical Reports Server (NTRS)

Swenson, B. L.; Edsinger, L. E.

1977-01-01

The preliminary feasibility of remote high-resolution infrared imagery of the space shuttle orbiter lower surface during entry to obtain accurate measurements of aerodynamic heat transfer to that vehicle was examined. In general, it was determined that such such images can be taken from an existing aircraft/telescope system (the C-141 AIRO) with a minimum modification or addition of systems using available technology. These images will have a spatial resolution of about 0.3 m and a temperature resolution much better than 2.5 percent. The data from these images will be at conditions and at a scale not reproducible in ground based facilities and should aid in the reduction of the prudent factors of safety required to account for phenomenological uncertainties on the thermal protection system design. Principal phenomena to be observed include laminar heating, boundary-layer transition, turbulent heating, surface catalysis, and flow separation and reattachment.

Long Duration Exposure Facility (LDEF) optical systems SIG summary and database

NASA Astrophysics Data System (ADS)

Bohnhoff-Hlavacek, Gail

1992-09-01

The main objectives of the Long Duration Exposure Facility (LDEF) Optical Systems Special Investigative Group (SIG) Discipline are to develop a database of experimental findings on LDEF optical systems and elements hardware, and provide an optical system overview. Unlike the electrical and mechanical disciplines, the optics effort relies primarily on the testing of hardware at the various principal investigator's laboratories, since minimal testing of optical hardware was done at Boeing. This is because all space-exposed optics hardware are part of other individual experiments. At this time, all optical systems and elements testing by experiment investigator teams is not complete, and in some cases has hardly begun. Most experiment results to date, document observations and measurements that 'show what happened'. Still to come from many principal investigators is a critical analysis to explain 'why it happened' and future design implications. The original optical system related concerns and the lessons learned at a preliminary stage in the Optical Systems Investigations are summarized. The design of the Optical Experiments Database and how to acquire and use the database to review the LDEF results are described.

Long Duration Exposure Facility (LDEF) optical systems SIG summary and database

NASA Technical Reports Server (NTRS)

Bohnhoff-Hlavacek, Gail

1992-01-01

The main objectives of the Long Duration Exposure Facility (LDEF) Optical Systems Special Investigative Group (SIG) Discipline are to develop a database of experimental findings on LDEF optical systems and elements hardware, and provide an optical system overview. Unlike the electrical and mechanical disciplines, the optics effort relies primarily on the testing of hardware at the various principal investigator's laboratories, since minimal testing of optical hardware was done at Boeing. This is because all space-exposed optics hardware are part of other individual experiments. At this time, all optical systems and elements testing by experiment investigator teams is not complete, and in some cases has hardly begun. Most experiment results to date, document observations and measurements that 'show what happened'. Still to come from many principal investigators is a critical analysis to explain 'why it happened' and future design implications. The original optical system related concerns and the lessons learned at a preliminary stage in the Optical Systems Investigations are summarized. The design of the Optical Experiments Database and how to acquire and use the database to review the LDEF results are described.

Air-Cored Linear Induction Motor for Earth-to-Orbit Systems

NASA Technical Reports Server (NTRS)

Zabar, Zivan; Levi, Enrico; Birenbaum, Leo

1996-01-01

The need for lowering the cost of Earth-to-Orbit (ETO) launches has prompted consideration of electromagnetic launchers. A preliminary design based on the experience gained in an advanced type of coilgun and on innovative ideas shows that such a launcher is technically feasible with almost off-the-shelf components.

A SEASAT report. Volume 1: Program summary

NASA Technical Reports Server (NTRS)

Pounder, E. (Editor)

1980-01-01

The program background and experiment objectives are summarized, and a description of the organization and interfaces of the project are provided. The mission plan and history are also included as well as user activities and a brief description of the data system. A financial and manpower summary and preliminary results of the mission are also included.

Drug Information to Patient Care Areas via Television: Preliminary Evaluation of Two Years' Experience

ERIC Educational Resources Information Center

Springer, Sandra J.; And Others

1978-01-01

The research project described was undertaken to study the impact of the use of a closed circuit television system to deliver information about drugs, chemicals, and poisons from a central resource location to health professionals in patient care areas. Evaluation techniques included questionnaires, interviews with users, and extramural…

Testing of Safety-Critical Software Embedded in an Artificial Heart

NASA Astrophysics Data System (ADS)

Cha, Sungdeok; Jeong, Sehun; Yoo, Junbeom; Kim, Young-Gab

Software is being used more frequently to control medical devices such as artificial heart or robotic surgery system. While much of software safety issues in such systems are similar to other safety-critical systems (e.g., nuclear power plants), domain-specific properties may warrant development of customized techniques to demonstrate fitness of the system on patients. In this paper, we report results of a preliminary analysis done on software controlling a Hybrid Ventricular Assist Device (H-VAD) developed by Korea Artificial Organ Centre (KAOC). It is a state-of-the-art artificial heart which completed animal testing phase. We performed software testing in in-vitro experiments and animal experiments. An abnormal behaviour, never detected during extensive in-vitro analysis and animal testing, was found.

Full-scale Transport Controlled Impact Demonstration Program

NASA Technical Reports Server (NTRS)

1987-01-01

The Federal Aviation Administration (FAA) and NASA conducted a full-scale air-to-surface impact-survivable impact demonstration with a remotely piloted transport aircraft on 1 December 1984, at Edwards Air Force Base, California. The test article consisted of experiments, special equipment, and supporting systems, such as antimisting kerosene (AMK), crashworthiness structural/restraint, analytical modeling, cabin fire safety, flight data recorders, post-impact investigation, instrumentation/data acquisition systems, remotely piloted vehicle/flight control systems, range and flight safety provisions, etc. This report describes the aircraft, experiments, systems, activities, and events which lead up to the Controlled Impact Demonstration (CID). An overview of the final unmanned remote control flight and sequence of impact events are delineated. Preliminary post CID observations are presented.

Analyzing high energy physics data using database computing: Preliminary report

NASA Technical Reports Server (NTRS)

Baden, Andrew; Day, Chris; Grossman, Robert; Lifka, Dave; Lusk, Ewing; May, Edward; Price, Larry

1991-01-01

A proof of concept system is described for analyzing high energy physics (HEP) data using data base computing. The system is designed to scale up to the size required for HEP experiments at the Superconducting SuperCollider (SSC) lab. These experiments will require collecting and analyzing approximately 10 to 100 million 'events' per year during proton colliding beam collisions. Each 'event' consists of a set of vectors with a total length of approx. one megabyte. This represents an increase of approx. 2 to 3 orders of magnitude in the amount of data accumulated by present HEP experiments. The system is called the HEPDBC System (High Energy Physics Database Computing System). At present, the Mark 0 HEPDBC System is completed, and can produce analysis of HEP experimental data approx. an order of magnitude faster than current production software on data sets of approx. 1 GB. The Mark 1 HEPDBC System is currently undergoing testing and is designed to analyze data sets 10 to 100 times larger.

Electrical Power Systems for NASA's Space Transportation Program

NASA Technical Reports Server (NTRS)

Lollar, Louis F.; Maus, Louis C.

1998-01-01

Marshall Space Flight Center (MSFC) is the National Aeronautics and Space Administration's (NASA) lead center for space transportation systems development. These systems include earth to orbit launch vehicles, as well as vehicles for orbital transfer and deep space missions. The tasks for these systems include research, technology maturation, design, development, and integration of space transportation and propulsion systems. One of the key elements in any transportation system is the electrical power system (EPS). Every transportation system has to have some form of electrical power and the EPS for each of these systems tends to be as varied and unique as the missions they are supporting. The Preliminary Design Office (PD) at MSFC is tasked to perform feasibility analyses and preliminary design studies for new projects, particularly in the space transportation systems area. All major subsystems, including electrical power, are included in each of these studies. Three example systems being evaluated in PD at this time are the Liquid Fly Back Booster (LFBB) system, the Human Mission to Mars (HMM) study, and a tether based flight experiment called the Propulsive Small Expendable Deployer System (ProSEDS). These three systems are in various stages of definition in the study phase.

Work Experiences of People with Mental Illness in Malaysia: A Preliminary Qualitative Study

ERIC Educational Resources Information Center

Boo, Su-Lyn; Loong, Jaymee; Ng, Wai-Sheng

2011-01-01

This is a preliminary qualitative study, using a basic interpretive approach, to investigate the work experiences of people with mental illness in Malaysia. Six females and four males (aged 30-70) from a residential home for the mentally ill participated in semi-structured interviews. Three inter-relating themes emerged, namely the experience of…

Gd uptake experiments for preliminary set of functionalized adsorbents

DOE Data Explorer

Clinton Noack

2015-03-16

These data summarize adsorption experiments conducted with Gd in 0.5 M NaCl. Results represent preliminary, proof-of-concept data utilizing fine-powder silica gel as the adsorbent support. Future testing will focus on larger, application-appropriate beads.

Preliminary Advanced Colloids Experiment

NASA Image and Video Library

2011-09-29

ISS029-E-011867 (29 Sept. 2011) --- NASA astronaut Mike Fossum, Expedition 29 commander, works with the Light Microscopy Module (LMM) control box in the Destiny laboratory of the International Space Station in preparation for another session with the Preliminary Advanced Colloids Experiment (PACE) hardware.

APEX 3D Propeller Test Preliminary Design

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.

2002-01-01

A low Reynolds number, high subsonic mach number flight regime is fairly uncommon in aeronautics. Most flight vehicles do not fly under these aerodynamic conditions. However, recently there have been a number of proposed aircraft applications (such as high altitude observation platforms and Mars aircraft) that require flight within this regime. One of the main obstacles to flight under these conditions is the ability to reliably generate sufficient thrust for the aircraft. For a conventional propulsion system, the operation and design of the propeller is the key aspect to its operation. Due to the difficulty in experimentally modeling the flight conditions in ground-based facilities, it has been proposed to conduct propeller experiments from a high altitude gliding platform (APEX). A preliminary design of a propeller experiment under the low Reynolds number, high mach number flight conditions has been devised. The details of the design are described as well as the potential data that will be collected.

Preliminary study of ground handling characteristics of Buoyant Quad Rotor (BQR) vehicles

NASA Technical Reports Server (NTRS)

Browning, R. G. E.

1980-01-01

A preliminary investigation of mooring concepts appropriate for heavy lift buoyant quad rotor (BQR) vehicles was performed. A review of the evolution of ground handling systems and procedures for all airship types is presented to ensure that appropriate consideration is given to past experiences. Two buoyant quad rotor designs are identified and described. An analysis of wind loads on a moored airship and the effects of these loads on vehicle design is provided. Four mooring concepts are assessed with respect to the airship design, wind loads and mooring site considerations. Basing requirements and applicability of expeditionary mooring at various operational scenarios are addressed.

Design, Modeling and Simulations in the RACE Project: Preliminary study for the development of a transport line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maidana, C. O.; Hunt, A. W.; Idaho State University, Department of Physics, PO Box 8106, Pocatello, ID 83209

2007-02-12

As part of the Reactor Accelerator Coupling Experiment (RACE) a set of preliminary studies were conducted to design a transport beam line that could bring a 25 MeV electron beam from a Linear Accelerator to a neutron-producing target inside a subcritical system. Because of the relatively low energy beam, the beam size and a relatively long beam line (implicating a possible divergence problem) different parameters and models were studied before a final design could be submitted for assembly. This report shows the first results obtained from different simulations of the transport line optics and dynamics.

Preliminary experiments of a single x-ray view catheter 3D localization algorithm for targeted stem cell injections

NASA Astrophysics Data System (ADS)

Iovea, M.; Creed, J.; Perin, E.; Neagu, M.; Mateiasi, G.

2009-02-01

The aim of this study was to conduct a preliminary check of a new method for measuring the 3D catheter position based on only one X-Ray view (image) and a simple pre-calibration procedure for catheters that could be equipped with high-opacity equal-spaced markers. The application chosen for this experiment is the targeted delivery of cell based therapeutic via a transendocardial retrograde approach into the left ventricle. This approach has shown promising therapeutic retention data when injected directly into the myocardial tissue, but lacks in the ability of the user to confidently manipulate the catheter within the left ventricle cavity space under traditional fluoroscopic guidance using a needle based catheter. The need for a new technique arose from the potential for increased safety and therapeutic efficacy by improving the targeting of the agent. The new technique, destined for Image guided catheter navigation systems for cardiac interventions, is based on a measurement of the marker's size and distance between them and followed by a comparison with the referenced catheter position. Preliminary experiments made with a simple phantom are presented, emphasizing the ability of the new technique in measuring the markers and the catheter tip 3D position. An overall maximum error in positioning markers and catheter tip below 12% has been obtained, yielding a promising result for continuing the future work of improving the algorithm accuracy.

High-frame-rate digital radiographic videography

NASA Astrophysics Data System (ADS)

King, Nicholas S. P.; Cverna, Frank H.; Albright, Kevin L.; Jaramillo, Steven A.; Yates, George J.; McDonald, Thomas E.; Flynn, Michael J.; Tashman, Scott

1994-10-01

High speed x-ray imaging can be an important tool for observing internal processes in a wide range of applications. In this paper we describe preliminary implementation of a system having the eventual goal of observing the internal dynamics of bone and joint reactions during loading. Two Los Alamos National Laboratory (LANL) gated and image intensified camera systems were used to record images from an x-ray image convertor tube to demonstrate the potential of high frame-rate digital radiographic videography in the analysis of bone and joint dynamics of the human body. Preliminary experiments were done at LANL to test the systems. Initial high frame-rate imaging (from 500 to 1000 frames/s) of a swinging pendulum mounted to the face of an X-ray image convertor tube demonstrated high contrast response and baseline sensitivity. The systems were then evaluated at the Motion Analysis Laboratory of Henry Ford Health Systems Bone and Joint Center. Imaging of a 9 inch acrylic disk with embedded lead markers rotating at approximately 1000 RPM, demonstrated the system response to a high velocity/high contrast target. By gating the P-20 phosphor image from the X-ray image convertor with a second image intensifier (II) and using a 100 microsecond wide optical gate through the second II, enough prompt light decay from the x-ray image convertor phosphor had taken place to achieve reduction of most of the motion blurring. Measurement of the marker velocity was made by using video frames acquired at 500 frames/s. The data obtained from both experiments successfully demonstrated the feasibility of the technique. Several key areas for improvement are discussed along with salient test results and experiment details.

Damage Detection and Verification System (DDVS) for In-Situ Health Monitoring

NASA Technical Reports Server (NTRS)

Williams, Martha K.; Lewis, Mark; Szafran, J.; Shelton, C.; Ludwig, L.; Gibson, T.; Lane, J.; Trautwein, T.

2015-01-01

Project presentation for Game Changing Program Smart Book Release. Detection and Verification System (DDVS) expands the Flat Surface Damage Detection System (FSDDS) sensory panels damage detection capabilities and includes an autonomous inspection capability utilizing cameras and dynamic computer vision algorithms to verify system health. Objectives of this formulation task are to establish the concept of operations, formulate the system requirements for a potential ISS flight experiment, and develop a preliminary design of an autonomous inspection capability system that will be demonstrated as a proof-of-concept ground based damage detection and inspection system.

Preliminary design for a maglev development facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coffey, H.T.; He, J.L.; Chang, S.L.

1992-04-01

A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable ofmore » powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh form 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.« less

Mini-DIAL system measurements coupled with multivariate data analysis to identify TIC and TIM simulants: preliminary absorption database analysis.

NASA Astrophysics Data System (ADS)

Gaudio, P.; Malizia, A.; Gelfusa, M.; Martinelli, E.; Di Natale, C.; Poggi, L. A.; Bellecci, C.

2017-01-01

Nowadays Toxic Industrial Components (TICs) and Toxic Industrial Materials (TIMs) are one of the most dangerous and diffuse vehicle of contamination in urban and industrial areas. The academic world together with the industrial and military one are working on innovative solutions to monitor the diffusion in atmosphere of such pollutants. In this phase the most common commercial sensors are based on “point detection” technology but it is clear that such instruments cannot satisfy the needs of the smart cities. The new challenge is developing stand-off systems to continuously monitor the atmosphere. Quantum Electronics and Plasma Physics (QEP) research group has a long experience in laser system development and has built two demonstrators based on DIAL (Differential Absorption of Light) technology could be able to identify chemical agents in atmosphere. In this work the authors will present one of those DIAL system, the miniaturized one, together with the preliminary results of an experimental campaign conducted on TICs and TIMs simulants in cell with aim of use the absorption database for the further atmospheric an analysis using the same DIAL system. The experimental results are analysed with standard multivariate data analysis technique as Principal Component Analysis (PCA) to develop a classification model aimed at identifying organic chemical compound in atmosphere. The preliminary results of absorption coefficients of some chemical compound are shown together pre PCA analysis.

Preliminary analysis on the water quality index (WQI) of irradiated basic filter elements

NASA Astrophysics Data System (ADS)

Arif Abu Bakar, Asyraf; Muhamad Pauzi, Anas; Aziz Mohamed, Abdul; Syima Sharifuddin, Syazrin; Mohamad Idris, Faridah

2018-01-01

Simple water filtration system is needed in times of extreme floods. Clean water for sanitation at evacuation centres is essential and its production is possible by using the famous simple filtration system consisting of empty bottle and filter elements (sands, gravels, cotton/coffee filter). This research intends to study the effects of irradiated filter elements on the filtration effectiveness through experiments. The filter elements will be irradiated with gamma and neutron radiation using the facilities available at Malaysia Nuclear Agency. The filtration effectiveness is measured using the water quality index (WQI) that is developed in this study to reflect the quality of filtered water. The WQI of the filtered water using the system with irradiated filter elements is then compared with that of the system with non-irradiated filter elements. This preliminary analysis only focus on filtration element of silica sand. Results shows very nominal variation in in WQI after filtered by non-irradiated, gamma and neutron filter element (silica sand), where the hypothesis could not be affirmed.

Status and future plans of the Drones for Aerodynamic and Structural Testing (DAST) program. [Aeroelastic Research Wing (ARW)

NASA Technical Reports Server (NTRS)

Murrow, H. N.

1981-01-01

Results from flight tests of the ARW-1 research wing are presented. Preliminary loads data and experiences with the active control system for flutter suppression are included along with comparative results of test and prediction for the flutter boundary of the supercritical research wing and on performance of the flutter suppression system. The status of the ARW-2 research wing is given.

A report from the Space Science and Engineering Center, the University of Wisconsin-Madison, Madison, Wisconsin

NASA Technical Reports Server (NTRS)

1985-01-01

Operational forecasters have habitually been plagued with the problems associated with acquisition, display, and dissemination of data used in preparing forecasts. The centralized storm information system (CSIS) experiment provided an operational forecaster with an interactive computer system which could perform these preliminary tasks more quickly and accurately than any human could. CSIS objectives pertaining to improved severe storms forecasting and warning procedures are addressed.

A persuasive toothbrush to enhance oral hygiene adherence.

PubMed

Walji, Muhammad F; Coker, Ololade; Valenza, John A; Henson, Harold; Warren-Morris, Donna; Zhong, Lin

2008-11-06

In this research we propose that a real-time wireless monitoring and reminder system can assist patients in maintaining optimal oral health. We provide a conceptual framework that incorporates both the behavioral and technical aspects of the proposed system. Further we present preliminary results of a feasibility experiment of modifying an inexpensive electric toothbrush by attaching an accelerometer and determining the ability to track motion and time by wirelessly transmitting data via Bluetooth technology.

Preliminary Design of a Modular Unmanned Research Vehicle. Volume 1. System Design Document

DTIC Science & Technology

1988-12-01

providing con- munications and restraint. 1-5 Tethered unpowered vehicle - an airplane-like body tether-mounted to an automobile , the auto providing...the velocity by towing. Auto-mounted vehicle - an airplane-like body rigidly mounted external to an automobile , the auto providing the velocity. Rail...accordingly. Based on this experiment, the MURV flight control system must be flexible in two ways: it should be reprogrammable for varying experimental

Gd uptake experiments for preliminary set of functionalized adsorbents (with content model)

DOE Data Explorer

Clinton Noack

2015-03-16

These data summarize adsorption experiments conducted with Gd in 0.5 M NaCl. Results represent preliminary, proof-of-concept data utilizing fine-powder silica gel as the adsorbent support. Future testing will focus on larger, application-appropriate beads.

LDEF: 69 Months in Space. Third Post-Retrieval Symposium, part 1

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1995-01-01

This volume (Part 1 of 3) is a compilation of papers presented at the Third Long Duration Exposure Facility (LDEF) Post-Retrieval Symposium. The papers represent the data analysis of the 57 experiments flown on the LDEF. The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, micrometeoroid, etc.), electronics, optics, and life science. In addition, papers on preliminary data analysis of EURECA, EOIM-3, and other spacecraft are included.

Automated Space Processing Payloads Study. Volume 1: Executive Summary

NASA Technical Reports Server (NTRS)

1975-01-01

An investigation is described which examined the extent to which the experiment hardware and operational requirements can be met by automatic control and material handling devices; payload and system concepts are defined which make extensive use of automation technology. Topics covered include experiment requirements and hardware data, capabilities and characteristics of industrial automation equipment and controls, payload grouping, automated payload conceptual design, space processing payload preliminary design, automated space processing payloads for early shuttle missions, and cost and scheduling.

LDEF: 69 Months in Space. Third Post-Retrieval Symposium, part 2

NASA Technical Reports Server (NTRS)

Levine, Arlene S. (Editor)

1995-01-01

This volume is a compilation of papers presented at the Third Long Duration Exposure Facility (LDEF) Post-Retrieval Symposium. The papers represent the data analysis of the 57 experiments flown on the LDEF. The experiments include materials, coatings, thermal systems, power and propulsion, science (cosmic ray, interstellar gas, heavy ions, micrometeoroid, etc.), electronics, optics, and life science. In addition, papers on preliminary data analysis of EURECA, EOIM-3, and other spacecraft are included. This second of three parts covers spacecraft construction materials.

Crystal-liquid-vapor equilibrium experiments at high temperature (less than or equal to 1800 C) and low, controlled oxygen and hydrogen pressure (10(-1) to 10(-9) PA)

NASA Technical Reports Server (NTRS)

Mysen, B. O.

1987-01-01

Evidence from carbonaceous chrondrites points to refractory oxides in the system CaO-MgO-Al2O3-TiO2-SiO2-Fe-O as being among the earliest phases to condense from the solar nebula. It is necessary to establish the equilibrium relationships between the relevant crystalline and amorphous phases before the chemical constraints can be meaningfully applied to models of solar system history. Preliminary experiments on earth show that such experiments are feasible. Earth-based experiments suffer from several unavoidable problems. These problems can be overcome by experimentation in the Space Station where the experiments can be conducted under near static pressure conditions and where total pressure equals the sum of controlled hydrogen and oxygen pressures and can be controlled for periods exceeding several hours.

Experience of superheat of solutions: doubly metastable systems

NASA Astrophysics Data System (ADS)

Skripov, P. V.

2017-11-01

The phenomenon of attainable superheat of two-component mixtures has been studied experimentally by the method of pulse heating of a wire probe. Special attention was called to the appearance of double metastability in the course of heating. Besides the usual superheating with respect to the liquid-vapor equilibrium temperature, the objects under study turn out to be supersaturated with respect to the carbon dioxide content. Preliminary experiments were carried out in the region of instability located above the diffusion spinodal. The results obtained lead to the choice of the program of further research on doubly metastable and unstable systems with different degrees of component compatibility.

Zero-gravity cloud physics laboratory: Experiment program definition and preliminary laboratory concept studies

NASA Technical Reports Server (NTRS)

Eaton, L. R.; Greco, E. V.

1973-01-01

The experiment program definition and preliminary laboratory concept studies on the zero G cloud physics laboratory are reported. This program involves the definition and development of an atmospheric cloud physics laboratory and the selection and delineations of a set of candidate experiments that must utilize the unique environment of zero gravity or near zero gravity.

Field Testing of a Two-Micron DIAL System for Profiling Atmospheric Carbon Dioxide

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Ismail, Syed; Koch, Grady J.; Diaz, Liza; Davis, Ken; Rubio, Manuel

2010-01-01

A 2-m DIAL system has been developed at NASA Langley Research Center through the NASA Instrument Incubator Program. The system utilizes a tunable 2-m pulsed laser and an IR phototransistor for the transmitter and the receiver, respectively. The system targets the CO2 absorption line R22 in the 2.05-m band. Field experiments were conducted at West Branch, Iowa, for evaluating the system for CO2 measurement by comparison with in-situ sensors. The CO2 in-situ sensors were located on the NOAA's WBI tower at 31, 99 and 379 m altitudes, besides the NOAA s aircraft was sampling at higher altitudes. Preliminary results demonstrated the capabilities of the DIAL system in profiling atmospheric CO2 using the 2-m wavelength. Results of these experiments will be presented and discussed.

MRI-guided procedures in various regions of the body using a robotic assistance system in a closed-bore scanner: preliminary clinical experience and limitations.

PubMed

Moche, Michael; Zajonz, Dirk; Kahn, Thomas; Busse, Harald

2010-04-01

To present the clinical setup and workflow of a robotic assistance system for image-guided interventions in a conventional magnetic resonance imaging (MRI) environment and to report our preliminary clinical experience with percutaneous biopsies in various body regions. The MR-compatible, servo-pneumatically driven, robotic device (Innomotion) fits into the 60-cm bore of a standard MR scanner. The needle placement (n = 25) accuracy was estimated by measuring the 3D deviation between needle tip and prescribed target point in a phantom. Percutaneous biopsies in six patients and different body regions were planned by graphically selecting entry and target points on intraoperatively acquired roadmap MR data. For insertion depths between 29 and 95 mm, the average 3D needle deviation was 2.2 +/- 0.7 mm (range 0.9-3.8 mm). Patients with a body mass index of up to approximately 30 kg/m(2) fitted into the bore with the device. Clinical work steps and limitations are reported for the various applications. All biopsies were diagnostic and could be completed without any major complications. Median planning and intervention times were 25 (range 20-36) and 44 (36-68) minutes, respectively. Preliminary clinical results in a standard MRI environment suggest that the presented robotic device provides accurate guidance for percutaneous procedures in various body regions. Shorter procedure times may be achievable by optimizing technical and workflow aspects. (c) 2010 Wiley-Liss, Inc.

Positioning Oneself for Leadership: Feelings of Vulnerability among Aspirant School Principals

ERIC Educational Resources Information Center

Gronn, Peter; Lacey, Kathy

2004-01-01

The research context for this article is the difficulty being experienced by a number of school systems, especially in the UK, USA, Canada and Australia, in recruiting principals. In our discussion we draw on preliminary findings from ongoing research into the experiences of a cohort of aspiring primary and secondary school principals. Our data…

Microsurgical robotic system for the deep surgical field: development of a prototype and feasibility studies in animal and cadaveric models.

PubMed

Morita, Akio; Sora, Shigeo; Mitsuishi, Mamoru; Warisawa, Shinichi; Suruman, Katopo; Asai, Daisuke; Arata, Junpei; Baba, Shoichi; Takahashi, Hidechika; Mochizuki, Ryo; Kirino, Takaaki

2005-08-01

To enhance the surgeon's dexterity and maneuverability in the deep surgical field, the authors developed a master-slave microsurgical robotic system. This concept and the results of preliminary experiments are reported in this paper. The system has a master control unit, which conveys motion commands in six degrees of freedom (X, Y, and Z directions; rotation; tip flexion; and grasping) to two arms. The slave manipulator has a hanging base with an additional six degrees of freedom; it holds a motorized operating unit with two manipulators (5 mm in diameter, 18 cm in length). The accuracy of the prototype in both shallow and deep surgical fields was compared with routine freehand microsurgery. Closure of a partial arteriotomy and complete end-to-end anastomosis of the carotid artery (CA) in the deep operative field were performed in 20 Wistar rats. Three routine surgical procedures were also performed in cadavers. The accuracy of pointing with the nondominant hand in the deep surgical field was significantly improved through the use of robotics. The authors successfully closed the partial arteriotomy and completely anastomosed the rat CAs in the deep surgical field. The time needed for stitching was significantly shortened over the course of the first 10 rat experiments. The robotic instruments also moved satisfactorily in cadavers, but the manipulators still need to be smaller to fit into the narrow intracranial space. Computer-controlled surgical manipulation will be an important tool for neurosurgery, and preliminary experiments involving this robotic system demonstrate its promising maneuverability.

Overview of Current Drive Experiment-Upgrade (CDX-U)

NASA Astrophysics Data System (ADS)

Hwang, Y. S.; Choe, W.; Stutman, D.; Lo, E.; Menard, J.; Ono, M.; Jones, T. G.; Armstrong, R.

1996-11-01

The CDX-U tokamak is a spherical tokamak (ST) facility with R ≈ 32 cm, R/a >= 1.4, and B_TF ≈ 1 kG. With an OH power supply of 60 mV-S capability, experiments were conducted with Ip up to ~ 100 kA and q(a) >= 3.5. The ST plasma performance has been studied along with various MHD-related activities. By appropriate discharge programing, it was possible to obtain MHD-quiescent discharges with a factor of 2 - 3 improvement in the electron energy confinement. Recently, the outer vacuum vessel was replaced with a toroidally continuous stainless steel chamber to accomodate the fast wave antenna. With the newly installed antenna, preliminary heating experiments using high harmonic fast waves have been pursued. The success of fast wave heating is a crucial element for achieving high beta plasmas in ST devices such as NSTX. Also, preliminary electron ripple injection (ERI) experiments were performed in CDX-U to examine the feasibility of this technique for improving ST tokamak confinement. To support the ST physics investigation, various novel plasma profile diagnostics such as the multi-pass Thomson scattering, soft x-ray tomography, and tangential-phase-contrast-imaging systems are under development on CDX-U.

Planned LMSS propagation experiment using ACTS: Preliminary antenna pointing results during mobile operations

NASA Technical Reports Server (NTRS)

Rowland, John R.; Goldhirsh, Julius; Vogel, Wolfhard J.; Torrence, Geoffrey W.

1991-01-01

An overview and a status description of the planned LMSS mobile K band experiment with ACTS is presented. As a precursor to the ACTS mobile measurements at 20.185 GHz, measurements at 19.77 GHz employing the Olympus satellite were originally planned. However, because of the demise of Olympus in June of 1991, the efforts described here are focused towards the ACTS measurements. In particular, we describe the design and testing results of a gyro controlled mobile-antenna pointing system. Preliminary pointing measurements during mobile operations indicate that the present system is suitable for measurements employing a 15 cm aperture (beamwidth at approximately 7 deg) receiving antenna operating with ACTS in the high gain transponder mode. This should enable measurements with pattern losses smaller than plus or minus 1 dB over more than 95 percent of the driving distance. Measurements with the present mount system employing a 60 cm aperture (beamwidth at approximately 1.7 deg) results in pattern losses smaller than plus or minus 3 dB for 70 percent of the driving distance. Acceptable propagation measurements may still be made with this system by employing developed software to flag out bad data points due to extreme pointing errors. The receiver system including associated computer control software has been designed and assembled. Plans are underway to integrate the antenna mount with the receiver on the University of Texas mobile receiving van and repeat the pointing tests on highways employing a recently designed radome system.

Preliminary design polymeric materials experiment. [for space shuttles and Spacelab missions

NASA Technical Reports Server (NTRS)

Mattingly, S. G.; Rude, E. T.; Marshner, R. L.

1975-01-01

A typical Advanced Technology Laboratory mission flight plan was developed and used as a guideline for the identification of a number of experiment considerations. The experiment logistics beginning with sample preparation and ending with sample analysis are then overlaid on the mission in order to have a complete picture of the design requirements. The results of this preliminary design study fall into two categories. First specific preliminary designs of experiment hardware which is adaptable to a variety of mission requirements. Second, identification of those mission considerations which affect hardware design and will require further definition prior to final design. Finally, a program plan is presented which will provide the necessary experiment hardware in a realistic time period to match the planned shuttle flights. A bibliography of all material reviewed and consulted but not specifically referenced is provided.

Payload isolation and stabilization by a Suspended Experiment Mount (SEM)

NASA Technical Reports Server (NTRS)

Bailey, Wayne L.; Desanctis, Carmine E.; Nicaise, Placide D.; Schultz, David N.

1992-01-01

Many Space Shuttle and Space Station payloads can benefit from isolation from crew or attitude control system disturbances. Preliminary studies have been performed for a Suspended Experiment Mount (SEM) system that will provide isolation from accelerations and stabilize the viewing direction of a payload. The concept consists of a flexible suspension system and payload-mounted control moment gyros. The suspension system, which is rigidly locked for ascent and descent, isolates the payload from high frequency disturbances. The control moment gyros stabilize the payload orientation. The SEM will be useful for payloads that require a lower-g environment than a manned vehicle can provide, such as materials processing, and for payloads that require stabilization of pointing direction, but not large angle slewing, such as nadir-viewing earth observation or solar viewing payloads.

Clouds and the Earth's Radiant Energy System (CERES)

NASA Technical Reports Server (NTRS)

Carman, Stephen L.; Cooper, John E.; Miller, James; Harrison, Edwin F.; Barkstrom, Bruce R.

1992-01-01

The CERES (Clouds and the Earth's Radiant Energy System) experiment will play a major role in NASA's multi-platform Earth Observing System (EOS) program to observe and study the global climate. The CERES instruments will provide EOS scientists with a consistent data base of accurately known fields of radiation and of clouds. CERES will investigate the important question of cloud forcing and its influence on the radiative energy flow through the Earth's atmosphere. The CERES instrument is an improved version of the ERBE (Earth Radiation Budget Experiment) broadband scanning radiometer flown by NASA from 1984 through 1989. This paper describes the science of CERES, presents an overview of the instrument preliminary design, and outlines the issues related to spacecraft pointing and attitude control.

[Preliminary study on breeding system of Prunella vulgaris].

PubMed

Wan, De-Qian; Guo, Qiao-Sheng; Liu, Li; Yang, Wei; Zhou, Man; Li, Yi-Min

2013-03-01

The research was conducted to study the breeding system of Prunella vulgaris L. Flowering dynamics was observed. Pollen viability, stigma receptivity, pollen-ovule ratio (P/O), out-crossing index (OCI) were measured. Bagging experiments were conducted. The results showed that the life span of one single flower was 1-2 days, the flowering span for the inflorescence of stalk was 7-14 days, the P/O was 1 046+/-148. 26, the OCI was 2. Combined with results of bagging experiment, the breeding system of P. vulgaris L. was mixed with cross-polination and self pollination. In the absence of pollination insects, the pollination and fertilization can be accomplished with high seed setting rate, and the seeds have a relatively high germination rate.

Assembling a prototype resonance electrical impedance spectroscopy system for breast tissue signal detection: preliminary assessment

NASA Astrophysics Data System (ADS)

Sumkin, Jules; Zheng, Bin; Gruss, Michelle; Drescher, John; Leader, Joseph; Good, Walter; Lu, Amy; Cohen, Cathy; Shah, Ratan; Zuley, Margarita; Gur, David

2008-03-01

Using electrical impedance spectroscopy (EIS) technology to detect breast abnormalities in general and cancer in particular has been attracting research interests for decades. Large clinical tests suggest that current EIS systems can achieve high specificity (>= 90%) at a relatively low sensitivity ranging from 15% to 35%. In this study, we explore a new resonance frequency based electrical impedance spectroscopy (REIS) technology to measure breast tissue EIS signals in vivo, which aims to be more sensitive to small tissue changes. Through collaboration between our imaging research group and a commercial company, a unique prototype REIS system has been assembled and preliminary signal acquisition has commenced. This REIS system has two detection probes mounted in the two ends of a Y-shape support device with probe separation of 60 mm. During REIS measurement, one probe touches the nipple and the other touches to an outer point of the breast. The electronic system continuously generates sweeps of multi-frequency electrical pulses ranging from 100 to 4100 kHz. The maximum electric voltage and the current applied to the probes are 1.5V and 30mA, respectively. Once a "record" command is entered, multi-frequency sweeps are recorded every 12 seconds until the program receives a "stop recording" command. In our imaging center, we have collected REIS measurements from 150 women under an IRB approved protocol. The database includes 58 biopsy cases, 78 screening negative cases, and other "recalled" cases (for additional imaging procedures). We measured eight signal features from the effective REIS sweep of each breast. We applied a multi-feature based artificial neural network (ANN) to classify between "biopsy" and normal "non-biopsy" breasts. The ANN performance is evaluated using a leave-one-out validation method and ROC analysis. We conducted two experiments. The first experiment attempted to classify 58 "biopsy" breasts and 58 "non-biopsy" breasts acquired on 58 women each having one breast recommended for biopsy. The second experiment attempted to classify 58 "biopsy" breasts and 58 negative breasts from the set of screening negative cases. The areas under ROC curves are 0.679 +/- 0.033 and 0.606 +/- 0.035 for the first and the second experiment, respectively. The preliminary results demonstrate (1) even with this rudimentary system with only one paired probes there is a measurable signal of changes in breast tissue demonstrating the feasibility of applying REIS technology for identifying at least some women with highly suspicious breast abnormalities and (2) the electromagnetic asymmetry between two breasts may be more sensitive in detecting changes in the abnormal breast. To further improve the REIS system performance, we are currently designing a new REIS system with multiple electrical probes and a more sophisticated analysis scheme.

An investigation of pre-launch and in-flight STS range safety radio signal degradation and dropout

NASA Technical Reports Server (NTRS)

Mcdonald, Malcolm W.

1991-01-01

The range safety system (RSS) transmitters operate at a frequency of 416.500 MHz. The transmitting antennas transmit left circularly polarized waves, and the shuttle range safety system (SRSS) receiving antennas onboard the shuttle vehicle receive left circular polarization. Preliminary explanations are proposed for many of the observed fluctuations in signal levels. It is recommended that experiments and further investigation be performed to test the validity of certain of these explanations.

The dish-Rankine SCSTPE program (Engineering Experiment no. 1). [systems engineering and economic analysis for a small community solar thermal electric system

NASA Technical Reports Server (NTRS)

Pons, R. L.; Grigsby, C. E.

1980-01-01

Activities planned for phase 2 Of the Small Community Solar Thermal Power Experiment (PFDR) program are summarized with emphasis on a dish-Rankine point focusing distributed receiver solar thermal electric system. Major design efforts include: (1) development of an advanced concept indirect-heated receiver;(2) development of hardware and software for a totally unmanned power plant control system; (3) implementation of a hybrid digital simulator which will validate plant operation prior to field testing; and (4) the acquisition of an efficient organic Rankine cycle power conversion unit. Preliminary performance analyses indicate that a mass-produced dish-Rankine PFDR system is potentially capable of producing electricity at a levelized busbar energy cost of 60 to 70 mills per KWh and with a capital cost of about $1300 per KW.

Hierarchical Modeling and Robust Synthesis for the Preliminary Design of Large Scale Complex Systems

NASA Technical Reports Server (NTRS)

Koch, Patrick N.

1997-01-01

Large-scale complex systems are characterized by multiple interacting subsystems and the analysis of multiple disciplines. The design and development of such systems inevitably requires the resolution of multiple conflicting objectives. The size of complex systems, however, prohibits the development of comprehensive system models, and thus these systems must be partitioned into their constituent parts. Because simultaneous solution of individual subsystem models is often not manageable iteration is inevitable and often excessive. In this dissertation these issues are addressed through the development of a method for hierarchical robust preliminary design exploration to facilitate concurrent system and subsystem design exploration, for the concurrent generation of robust system and subsystem specifications for the preliminary design of multi-level, multi-objective, large-scale complex systems. This method is developed through the integration and expansion of current design techniques: Hierarchical partitioning and modeling techniques for partitioning large-scale complex systems into more tractable parts, and allowing integration of subproblems for system synthesis; Statistical experimentation and approximation techniques for increasing both the efficiency and the comprehensiveness of preliminary design exploration; and Noise modeling techniques for implementing robust preliminary design when approximate models are employed. Hierarchical partitioning and modeling techniques including intermediate responses, linking variables, and compatibility constraints are incorporated within a hierarchical compromise decision support problem formulation for synthesizing subproblem solutions for a partitioned system. Experimentation and approximation techniques are employed for concurrent investigations and modeling of partitioned subproblems. A modified composite experiment is introduced for fitting better predictive models across the ranges of the factors, and an approach for constructing partitioned response surfaces is developed to reduce the computational expense of experimentation for fitting models in a large number of factors. Noise modeling techniques are compared and recommendations are offered for the implementation of robust design when approximate models are sought. These techniques, approaches, and recommendations are incorporated within the method developed for hierarchical robust preliminary design exploration. This method as well as the associated approaches are illustrated through their application to the preliminary design of a commercial turbofan turbine propulsion system. The case study is developed in collaboration with Allison Engine Company, Rolls Royce Aerospace, and is based on the Allison AE3007 existing engine designed for midsize commercial, regional business jets. For this case study, the turbofan system-level problem is partitioned into engine cycle design and configuration design and a compressor modules integrated for more detailed subsystem-level design exploration, improving system evaluation. The fan and low pressure turbine subsystems are also modeled, but in less detail. Given the defined partitioning, these subproblems are investigated independently and concurrently, and response surface models are constructed to approximate the responses of each. These response models are then incorporated within a commercial turbofan hierarchical compromise decision support problem formulation. Five design scenarios are investigated, and robust solutions are identified. The method and solutions identified are verified by comparison with the AE3007 engine. The solutions obtained are similar to the AE3007 cycle and configuration, but are better with respect to many of the requirements.

Using a Red Team to devise countermeasures

NASA Astrophysics Data System (ADS)

Swedenburg, R. L.

1995-01-01

The ability of a defense system to operate effectively when deployed in battle is dependent on designs able to deal with countermeasures against the defense. The formation of a technical Red Team to stress the preliminary designs of the defensive system with technologically feasible and effective potential countermeasures provides a means to identify such potential countermeasures. This paper describes the experience of the U.S. Ballistic Missile Defense Organization's (BMDO) Theater Missile Defense Red Team since the Gulf War in 1991, the Red-Blue Exchange process, and the value it has provided to the designers of the U.S. Theater Missile Defense systems for developing robust systems. A wide-range of technologically feasible countermeasures has been devised, analyzed, tested for feasibility, and provided to the system developers for mitigation design. The process for independently analyzing possible susceptibilities of preliminary designs and exploiting the susceptibilities to identify possible countermeasures is explained. Designing and characterizing the Red Team's countermeasures, determining their feasibility, and analyzing their potential effectiveness against the defense are explained. A technique for the Blue Team's designers to deal with a wide range of potential countermeasures is explained.

Experiment plans to study preignition processes of a pool fire in low gravity. M.S. Thesis - 1988 Final Report

NASA Technical Reports Server (NTRS)

Schiller, David N.

1989-01-01

Science requirements are specified to guide experimental studies of transient heat transfer and fluid flow in an enclosure containing a two-layer gas-and-liquid system heated unevenly from above. Specifications are provided for experiments in three separate settings: (1) a normal gravity laboratory, (2) the NASA-LeRC Drop towers, and (3) a space-based laboratory (e.g., Shuttle, Space Station). A rationale is developed for both minimum and desired requirement levels. The principal objective of the experimental effort is to validate a computational model of the enclosed liquid fuel pool during the preignition phase and to determine via measurement the role of gravity on the behavior of the system. Preliminary results of single-phase normal gravity experiments and simulations are also presented.

Preliminary study of a hydrogen peroxide rocket for use in moving source jet noise tests

NASA Technical Reports Server (NTRS)

Plencner, R. M.

1977-01-01

A preliminary investigation was made of using a hydrogen peroxide rocket to obtain pure moving source jet noise data. The thermodynamic cycle of the rocket was analyzed. It was found that the thermodynamic exhaust properties of the rocket could be made to match those of typical advanced commercial supersonic transport engines. The rocket thruster was then considered in combination with a streamlined ground car for moving source jet noise experiments. When a nonthrottlable hydrogen peroxide rocket was used to accelerate the vehicle, propellant masses and/or acceleration distances became too large. However, when a throttlable rocket or an auxiliary system was used to accelerate the vehicle, reasonable propellant masses could be obtained.

Summer research program (1992). Summer faculty research program (SFRP) reports. Volume 6. Arnold Engineering Development Center, Civil Engineering Laboratory, Frank J. Seiler research laboratory, Wilford Hall Medical Center. Annual report, 1 September 1991-31 August 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, G.

1992-12-28

The following Topics were among those completed at the Air Force Faculty Research Summer Program: Experiences using Model-Based Techniques for the Development of a Large Parallel Instrumentation System; Data Reduction of Laser Induced Fluorescence in Rocket Motor Exhausts; Feasibility of Wavelet Analysis for Plume Data Study; Characterization of Seagrass Meadows in St. Andrew (Crooked Island) Sound, Northern Gulf of Mexico; A Preliminary Study of the Weathering of Jet Fuels in Soil Monitored by SFE with GC Analysis; Preliminary Numerical model of Groundwater Flow at the MADE2 Site.

Use of Taguchi design of experiments to optimize and increase robustness of preliminary designs

NASA Technical Reports Server (NTRS)

Carrasco, Hector R.

1992-01-01

The research performed this summer includes the completion of work begun last summer in support of the Air Launched Personnel Launch System parametric study, providing support on the development of the test matrices for the plume experiments in the Plume Model Investigation Team Project, and aiding in the conceptual design of a lunar habitat. After the conclusion of last years Summer Program, the Systems Definition Branch continued with the Air Launched Personnel Launch System (ALPLS) study by running three experiments defined by L27 Orthogonal Arrays. Although the data was evaluated during the academic year, the analysis of variance and the final project review were completed this summer. The Plume Model Investigation Team (PLUMMIT) was formed by the Engineering Directorate to develop a consensus position on plume impingement loads and to validate plume flowfield models. In order to obtain a large number of individual correlated data sets for model validation, a series of plume experiments was planned. A preliminary 'full factorial' test matrix indicated that 73,024 jet firings would be necessary to obtain all of the information requested. As this was approximately 100 times more firings than the scheduled use of Vacuum Chamber A would permit, considerable effort was needed to reduce the test matrix and optimize it with respect to the specific objectives of the program. Part of the First Lunar Outpost Project deals with Lunar Habitat. Requirements for the habitat include radiation protection, a safe haven for occasional solar flare storms, an airlock module as well as consumables to support 34 extra vehicular activities during a 45 day mission. The objective for the proposed work was to collaborate with the Habitat Team on the development and reusability of the Logistics Modules.

U-Mo Plate Blister Anneal Interim Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francine J. Rice; Daniel M. Wachs; Adam B. Robinson

2010-10-01

Blister thresholds in fuel elements have been a longstanding performance parameter for fuel elements of all types. This behavior has yet to be fully defined for the RERTR U-Mo fuel types. Blister anneal studies that began in 2007 have been expanded to include plates from more recent RERTR experiments. Preliminary data presented in this report encompasses the early generations of the U-Mo fuel systems and the most recent but still developing fuel system. Included is an overview of relevant dispersion fuel systems for the purposes of comparison.

Millimeter wave propagation measurements using the ATS 5 satellite

NASA Technical Reports Server (NTRS)

Ippolito, L. J.

1972-01-01

The ATS 5 millimeter wave propagation experiment determines long- and short-term attenuation statistics of operational millimeter wavelength earthspace links as functions of defined meteorological conditions. A preliminary analysis of results with 15 GHz downlink and 32 GHz uplink frequency bands indicates that both frequency bands exhibit an excellent potential for utilization in reliable high data rate earth-space communications systems.

High Energy Astronomy Observatory, Mission C, Phase A. Volume 2: Preliminary analyses and conceptual design

NASA Technical Reports Server (NTRS)

1972-01-01

An analysis and conceptual design of a baseline mission and spacecraft are presented. Aspects of the HEAO-C discussed include: baseline experiments with X-ray observations of space, analysis of mission requirements, observatory design, structural analysis, thermal control, attitude sensing and control system, communication and data handling, and space shuttle launch and retrieval of HEAO-C.

BRIDGE - Behavioural reaching interfaces during daily antigravity activities through upper limb exoskeleton: Preliminary results.

PubMed

Gandolla, Marta; Costa, Andrea; Aquilante, Lorenzo; Gfoehler, Margit; Puchinger, Markus; Braghin, Francesco; Pedrocchi, Alessandra

2017-07-01

People with neuromuscular diseases such as muscular dystrophy experience a distributed and evolutive weakness in the whole body. Recent technological developments have changed the daily life of disabled people strongly improving the perceived quality of life, mostly concentrating on powered wheelchairs, so to assure autonomous mobility and respiratory assistance, essential for survival. The key concept of the BRIDGE project is to contrast the everyday experience of losing functions by providing them of a system able to exploit the best their own residual capabilities in arm movements so to keep them functional and autonomous as much as possible. BRIDGE is composed by a light, wearable and powered five degrees of freedom upper limb exoskeleton under the direct control of the user through a joystick or gaze control. An inverse kinematic model allows to determine joints position so to track patient desired hand position. BRIDGE prototype has been successfully tested in simulation environment, and by a small group of healthy volunteers. Preliminary results show a good tracking performance of the implemented control scheme. The interaction procedure was easy to understand, and the interaction with the system was successful.

Protein separation through preliminary experiments concerning pH and salt concentration by tube radial distribution chromatography based on phase separation multiphase flow using a polytetrafluoroethylene capillary tube.

PubMed

Kan, Hyo; Tsukagoshi, Kazuhiko

2017-07-01

Protein mixtures were separated using tube radial distribution chromatography (TRDC) in a polytetrafluoroethylene (PTFE) capillary (internal diameter=100µm) separation tube. Separation by TRDC is based on the annular flow in phase separation multiphase flow and features an open-tube capillary without the use of specific packing agents or application of high voltages. Preliminary experiments were conducted to examine the effects of pH and salt concentration on the phase diagram of the ternary mixed solvent solution of water-acetonitrile-ethyl acetate (8:2:1 volume ratio) and on the TRDC system using the ternary mixed solvent solution. A model protein mixture containing peroxidase, lysozyme, and bovine serum albumin was analyzed via TRDC with the ternary mixed solvent solution at various pH values, i.e., buffer-acetonitrile-ethyl acetate (8:2:1 volume ratio). Protein was separated on the chromatograms by the TRDC system, where the elution order was determined by the relation between the isoelectric points of protein and the pH values of the solvent solution. Copyright © 2017 Elsevier B.V. All rights reserved.

Tunable solid-state laser technology for applications to scientific and technological experiments from space

NASA Technical Reports Server (NTRS)

Allario, F.; Taylor, L. V.

1986-01-01

Current plans for the Earth Observing System (EOS) include development of a lidar facility to conduct scientific experiments from a polar orbiting platforms. A recommended set of experiments were scoped, which includes techniques of atmospheric backscatter (Lidar), Differential Absorption Lidar (DIAL), altimetry, and retroranging. Preliminary assessments of the resources (power, weight, volume) required by the Eos Lidar Facility were conducted. A research program in tunable solid state laser technology was developed, which includes laser materials development, modeling and experiments on the physics of solid state laser materials, and development of solid state laser transmitters with a strong focus on Eos scientific investigations. Some of the system studies that were conducted which highlight the payoff of solid state laser technology for the Eos scientific investigations will be discussed. Additionally, a summary of some promising research results which have recently emerged from the research program will be presented.

The service telemetry and control device for space experiment “GRIS”

NASA Astrophysics Data System (ADS)

Glyanenko, A. S.

2016-02-01

Problems of scientific devices control (for example, fine control of measuring paths), collecting auxiliary (service information about working capacity, conditions of experiment carrying out, etc.) and preliminary data processing are actual for any space device. Modern devices for space research it is impossible to imagine without devices that didn't use digital data processing methods and specialized or standard interfaces and computing facilities. For realization of these functions in “GRIS” experiment onboard ISS for purposes minimization of dimensions, power consumption, the concept “system-on-chip” was chosen and realized. In the programmable logical integrated scheme by Microsemi from ProASIC3 family with maximum capacity up to 3M system gates, the computing kernel and all necessary peripherals are created. In this paper we discuss structure, possibilities and resources the service telemetry and control device for “GRIS” space experiment.

Anaesthesiologists' views on the need for point-of-care information system in the operating room: a survey of the European Society of Anaesthesiologists.

PubMed

Perel, A; Berkenstadt, H; Ziv, A; Katzenelson, R; Aitkenhead, A

2004-11-01

In this preliminary study we wanted to explore the attitudes of anaesthesiologists to a point-of-care information system in the operating room. The study was conducted as a preliminary step in the process of developing such a system by the European Society of Anaesthesiologists (ESA). A questionnaire was distributed to all 2240 attendees of the ESA's annual meeting in Gothenburg, Sweden, which took place in April 2001. Of the 329 responders (response rate of 14.6%), 79% were qualified specialists with more than 10 yr of experience (68%), mostly from Western Europe. Most responders admitted to regularly experiencing lack of medical knowledge relating to real-time patient care at least once a month (74%) or at least once a week (46%), and 39% admitted to having made errors during anaesthesia due to lack of medical information that can be otherwise found in a handbook. The choice ofa less optimal but more familiar approach to patient management due to lack of knowledge was reported by 37%. Eighty-eight percent of responders believe that having a point-of-care information system for the anaesthesiologists in the operating room is either important or very important. This preliminary survey demonstrates that lack of knowledge of anaesthesiologists may be a significant source of medical errors in the operating room, and suggests that a point-of-care information system for the anaesthesiologist may be of value.

The Global Modeling and Assimilation Office (GMAO) 4d-Var and its Adjoint-based Tools

NASA Technical Reports Server (NTRS)

Todling, Ricardo; Tremolet, Yannick

2008-01-01

The fifth generation of the Goddard Earth Observing System (GEOS-5) Data Assimilation System (DAS) is a 3d-var system that uses the Grid-point Statistical Interpolation (GSI) system developed in collaboration with NCEP, and a general circulation model developed at Goddard, that includes the finite-volume hydrodynamics of GEOS-4 wrapped in the Earth System Modeling Framework and physical packages tuned to provide a reliable hydrological cycle for the integration of the Modern Era Retrospective-analysis for Research and Applications (MERRA). This MERRA system is essentially complete and the next generation GEOS is under intense development. A prototype next generation system is now complete and has been producing preliminary results. This prototype system replaces the GSI-based Incremental Analysis Update procedure with a GSI-based 4d-var which uses the adjoint of the finite-volume hydrodynamics of GEOS-4 together with a vertical diffusing scheme for simplified physics. As part of this development we have kept the GEOS-5 IAU procedure as an option and have added the capability to experiment with a First Guess at the Appropriate Time (FGAT) procedure, thus allowing for at least three modes of running the data assimilation experiments. The prototype system is a large extension of GEOS-5 as it also includes various adjoint-based tools, namely, a forecast sensitivity tool, a singular vector tool, and an observation impact tool, that combines the model sensitivity tool with a GSI-based adjoint tool. These features bring the global data assimilation effort at Goddard up to date with technologies used in data assimilation systems at major meteorological centers elsewhere. Various aspects of the next generation GEOS will be discussed during the presentation at the Workshop, and preliminary results will illustrate the discussion.

Multiphase Flow Technology Impacts on Thermal Control Systems for Exploration

NASA Technical Reports Server (NTRS)

McQuillen, John; Sankovic, John; Lekan, Jack

2006-01-01

The Two-Phase Flow Facility (TPHIFFy) Project focused on bridging the critical knowledge gap by developing and demonstrating critical multiphase fluid products for advanced life support, thermal management and power conversion systems that are required to enable the Vision for Space Exploration. Safety and reliability of future systems will be enhanced by addressing critical microgravity fluid physics issues associated with flow boiling, condensation, phase separation, and system stability. The project included concept development, normal gravity testing, and reduced gravity aircraft flight campaigns, in preparation for the development of a space flight experiment implementation. Data will be utilized to develop predictive models that could be used for system design and operation. A single fluid, two-phase closed thermodynamic loop test bed was designed, assembled and tested. The major components in this test bed include: a boiler, a condenser, a phase separator and a circulating pump. The test loop was instrumented with flow meters, thermocouples, pressure transducers and both high speed and normal speed video cameras. A low boiling point surrogate fluid, FC-72, was selected based on scaling analyses using preliminary designs for operational systems. Preliminary results are presented which include flow regime transitions and some observations regarding system stability.

THE MORPHOLOGICAL BASIS FOR OLFACTORY PERCEPTION OF STEROIDS DUING AGONISTIC BEHAVIOR IN LOBSTER: PRELIMINARY EXPERIMENTS

EPA Science Inventory

The morphological basis for olfactory perception of steroids during agonistic behavior in lobsters: preliminary experiments. Borsay Horowitz, DJ1, Kass-Simon, G2, Coglianese, D2, Martin, L2, Boseman, M2, Cromarty, S3, Randall, K3, Fini, A.3 1US EPA, NHEERL, ORD, Atlantic Ecology...

Global Experience: The Development and Preliminary Evaluation of a Programme Designed to Enhance Students' Global Engagement

ERIC Educational Resources Information Center

Feast, Vicki; Collyer-Braham, Sarah; Bretag, Tracey

2011-01-01

This paper reports on the development and preliminary evaluation of "Global Experience", an innovative programme at the University of South Australia designed to broaden students' intercultural engagement through a range of international experiential activities. The paper provides the rationale for the establishment of the programme…

Airborne LIDAR Measurements of Water Vapor, Ozone, Clouds, and Aerosols in the Tropics Near Central America During the TC4 Experiment

NASA Technical Reports Server (NTRS)

Kooi, Susan; Fenn, Marta; Ismail, Syed; Ferrare, Richard; Hair, John; Browell, Edward; Notari, Anthony; Butler, Carolyn; Burton, Sharon; Simpson, Steven

2008-01-01

Large scale distributions of ozone, water vapor, aerosols, and clouds were measured throughout the troposphere by two NASA Langley lidar systems on board the NASA DC-8 aircraft as part of the Tropical Composition, Cloud, and Climate Coupling Experiment (TC4) over Central and South America and adjacent oceans in the summer of 2007. Special emphasis was placed on the sampling of convective outflow and transport, sub-visible cirrus clouds, boundary layer aerosols, Saharan dust, volcanic emissions, and urban and biomass burning plumes. This paper presents preliminary results from this campaign, and demonstrates the value of coordinated measurements by the two lidar systems.

A Consistent System for Coding Laboratory Samples

NASA Astrophysics Data System (ADS)

Sih, John C.

1996-07-01

A formal laboratory coding system is presented to keep track of laboratory samples. Preliminary useful information regarding the sample (origin and history) is gained without consulting a research notebook. Since this system uses and retains the same research notebook page number for each new experiment (reaction), finding and distinguishing products (samples) of the same or different reactions becomes an easy task. Using this system multiple products generated from a single reaction can be identified and classified in a uniform fashion. Samples can be stored and filed according to stage and degree of purification, e.g. crude reaction mixtures, recrystallized samples, chromatographed or distilled products.

Preliminary results of passive microwave snow experiment during February and March 1978

NASA Technical Reports Server (NTRS)

Chang, A. T. C.; Shiue, J. C.; Boyne, H.; Ellerbruch, D.; Counas, G.; Wittmann, R.; Jones, R.

1979-01-01

The purpose of the experiment was to determine if remote microwave sensing of snowpack data could be used to predict runoff, thereby allowing more efficient management of the water supply. A four-frequency microwave radiometer system was attached to a truck-mounted aerial lift and was used to gather data on snowpacks at three different sites in the Colorado Rocky Mountains. Ground truth data measurements (density, temperature, grain size, hardness, and free-liquid water content) were taken at each site corresponding to each microwave scan.

An active constraint environment for minimally invasive heart surgery: early experience of a cutting operation.

PubMed

Borelli, Joao; Bello, Fernando; Rodriguez Y Bena, Ferdinando; Davies, Brian

2004-01-01

Master/slave telemanipulator systems can be applied in minimally invasive heart surgery. However, due to the beating heart and difficulties of finding inner points inside the heart, a surgical task operation such as cutting can be very difficult. In order to avoid surgical error, the "active constraint" concept can be applied. This paper shows an example of an "active constraint" environment used for minimally invasive heart surgery. Experiments have been carried out for a 2-DOF master and the preliminary results validate the present approach.

Preliminary design and hazards report. Boiling Reactor Experiment V (BORAX V)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, R. E.

1960-02-01

The preliminary objectives of the proposed BORAX V program are to test nuclear superheating concepts and to advance the technology of boiling-water-reactor design by performing experiments which will improve the understanding of factors limiting the stability of boiling reactors at high power densities. The reactor vessel is a cylinder with ellipsoidal heads, made of carbon steel clad internally with stainless steel. Each of the three cores is 24 in. high and has an effective diameter of 39 in. This is a preliminary report. (W.D.M.)

Preliminary flight test results from the advanced photovoltaic experiment

NASA Technical Reports Server (NTRS)

Brinker, David J.; Hickey, John R.

1990-01-01

The Advanced Photovoltaic Experiment is a space flight test designed to provide reference cell standards for photovoltaic measurement as well as to investigate the solar spectrum and the effect of the space environment on solar cells. After a flight of 69 months in low earth orbit as part of the Long Duration Exposure Facility set of experiments, it was retrieved in January, 1990. The electronic data acquisition system functioned as designed, measuring and recording cell performance data over the first 358 days of flight, limited by battery lifetime. Significant physical changes are also readily apparent, including erosion of front surface paint, micrometeoroid and debris catering and contamination.

Preliminary results from the advanced photovoltaic experiment flight test

NASA Technical Reports Server (NTRS)

Brinker, David J.; Hart, Russell E., Jr.; Hickey, John R.

1990-01-01

The Advanced Photovoltaic Experiment is a space flight test designed to provide reference cell standards for photovoltaic measurement as well as to investigate the solar spectrum and the effect of the space environment on solar cells. After a flight of 69 months in low earth orbit as part of the Long Duration Exposure Facility set of experiments, it was retrieved in January, 1990. The electronic data acquisition system functioned as designed, measuring and recording cell performance data over the first 358 days of flight; limited by battery lifetime. Significant physical changes are also readily apparent, including erosion of front surface paint, micrometeoroid and debris catering and contamination.

The INPE handouts to the 6th LANDSAT Technical Working Group (LTWG) Meeting

NASA Technical Reports Server (NTRS)

Debarrosaguirre, J. L. (Principal Investigator); Parada, L. E. M.; Depaulapereira, S.

1984-01-01

LANDSAT receiving and processing system in its present configuration and status are described, as well as the experience already obtained with LANDSATs 4 and 5. The revised table of station plans for TM reception and products and of implementation schedule for data formats employing superstructure conventions is updated. Standardization of the worldwide reference systems is proposed. The INPE preliminary TM products price list is included. A TM image received and processed is shown to illustrate the appearance of the products offered.

The Application of MP-FTS to Aperture Synthesis

NASA Astrophysics Data System (ADS)

Hattori, M.; Ohta, I. S.; Matsuo, H.; Shibata, Y.

2000-12-01

The application of the Martin-Puplett type Fourier transform spectrometer to aperture synthesis is considered. The configuration of the mirrors and beam splitters and the fundamental mathematical elements of the system are summarized. We show that the system can measure spectrally resolved spatial distribution of the Stokes parameters of sources as interfered signals. An original Martin-Puplett type Fourier transform spectrometer that can be applied to aperture synthesis in mm and sub-mm wave bands has been constructed. The preliminary results of our laboratory experiments are reported.

General purpose free floating platform for KC-135 flight experimentation

NASA Technical Reports Server (NTRS)

Borchers, Bruce A.; Yendler, Boris S.; Kliss, Mark H.; Gonzales, Andrew A.; Edwards, Mark T.

1994-01-01

The Controlled Ecological Life Support Systems (CELSS) program is evaluating higher plants as a means of providing life support functions aboard space craft. These plant systems will be capable of regenerating air and water while meeting some of the food requirements of the crew. In order to grow plants in space, a series of systems are required to provide the necessary plant support functions. Some of the systems required for CELSS experiments are such that is is likely that existing technologies will require refinement, or novel technologies will need to be developed. To evaluate and test these technologies, a series of KC-135 precursor flights are being proposed. A general purpose free floating experiment platform is being developed to allow the KC-135 flights to be used to their fullest. This paper will outline the basic design for the CELSS Free Floating Test Bed (FFTB), and the requirements for the individual subsystems. Several preliminary experiments suitable for the free floater will also be discussed.

A haptic pedal for surgery assistance.

PubMed

Díaz, Iñaki; Gil, Jorge Juan; Louredo, Marcos

2014-09-01

The research and development of mechatronic aids for surgery is a persistent challenge in the field of robotic surgery. This paper presents a new haptic pedal conceived to assist surgeons in the operating room by transmitting real-time surgical information through the foot. An effective human-robot interaction system for medical practice must exchange appropriate information with the operator as quickly and accurately as possible. Moreover, information must flow through the appropriate sensory modalities for a natural and simple interaction. However, users of current robotic systems might experience cognitive overload and be increasingly overwhelmed by data streams from multiple modalities. A new haptic channel is thus explored to complement and improve existing systems. A preliminary set of experiments has been carried out to evaluate the performance of the proposed system in a virtual surgical drilling task. The results of the experiments show the effectiveness of the haptic pedal in providing surgical information through the foot. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

The InKiIsSy experiment at LNS: A study of size vs. isospin effects with 124Xe + 64Zn , 64Ni reactions at 35 A MeV

NASA Astrophysics Data System (ADS)

Norella, S.; Acosta, L.; Auditore, L.; Baran, V.; Cap, T.; Cardella, G.; Colonna, M.; De Filippo, E.; Dell'Aquila, D.; De Luca, S.; Francalanza, L.; Gnoffo, B.; Lanzalone, G.; Lombardo, I.; Maiolino, C.; Martorana, N. S.; Minniti, T.; Pagano, A.; Pagano, E. V.; Papa, M.; Piasecki, E.; Pirrone, S.; Politi, G.; Porto, F.; Quattrocchi, L.; Rizzo, F.; Rosato, E.; Russotto, P.; Siwek-Wilczynska, K.; Trifirò, A.; Trimarchi, M.; Verde, G.; Vigilante, M.; Wilczyński, J.

2017-11-01

In previous experiments, performed by CHIMERA Collaboration, a strong difference in the cross sections of "dynamical" PLF binary decay between neutron-poor 112Sn (35 A MeV)+ 58Ni and neutron-rich 124Sn (35 A MeV)+ 64Ni colliding systems has been reported. The same effect was not seen in the "statistical" binary decay. The observed difference was related to the different N/ Z content between the two systems. However, size effects could not be excluded. In order to disentangle Isospin effects from size ones, the systems 124Xe (35 A MeV)+ 64Zn ( 64Ni were studied in the InKiIsSy (Inverse Kinematic Isobaric Systems) experiment, carried out at Laboratori Nazionali del Sud on April 2013, using the multi-detector CHIMERA and 4 prototype-modules of FARCOS array. We will report preliminary results on the binary PLF splitting mechanism.

Road-map to plan and structure the preliminary site investigation program for a geological repository in Japan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deguchi, Akira; Tsuchi, Hiroyuki; Kitayama, Kazumi

2007-07-01

Available in abstract form only. Full text of publication follows: A stepwise site selection process has been adopted for geological disposal of HLW in Japan. Literature surveys (LS), followed by preliminary investigations (PI) and, finally, detailed investigations (DI) in underground facilities will be carried out in the successive selection stages. In the PI stage, surface-based investigations such as borehole surveys and geophysical prospecting will be implemented with two main objectives. The first is to obtain information relating to legal requirements on siting, such as the occurrence of igneous or fault activity, and to confirm the extremely low likelihood of adversemore » impacts on the candidate site resulting from such phenomena. The second is to obtain the information required for the design and performance assessment of the engineered barrier system and the repository. In order to implement these preliminary investigations rigorously and efficiently within the constraints of a limited time period, budget and resources, PI planning before commencing investigations and on-site PI management during the investigation phase are very important issues. The planning and management of PI have to be performed by NUMO staff, but not all staff have sufficient experience in the range of disciplines involved. NUMO therefore decided to compile existing knowledge and experience in the planning and management of investigations in the form of manuals to be used to improve and maintain internal expertise. Experts with experience in overseas investigation programs were requested to prepare these manuals. This paper outlines the structure and scope of the upper level manual (road-map) and discusses NUMO's experience in applying it in 'dry-runs' to model sites. (authors)« less

Development and preliminary validation of an interactive remote physical therapy system.

PubMed

Mishra, Anup K; Skubic, Marjorie; Abbott, Carmen

2015-01-01

In this paper, we present an interactive physical therapy system (IPTS) for remote quantitative assessment of clients in the home. The system consists of two different interactive interfaces connected through a network, for a real-time low latency video conference using audio, video, skeletal, and depth data streams from a Microsoft Kinect. To test the potential of IPTS, experiments were conducted with 5 independent living senior subjects in Kansas City, MO. Also, experiments were conducted in the lab to validate the real-time biomechanical measures calculated using the skeletal data from the Microsoft Xbox 360 Kinect and Microsoft Xbox One Kinect, with ground truth data from a Vicon motion capture system. Good agreements were found in the validation tests. The results show potential capabilities of the IPTS system to provide remote physical therapy to clients, especially older adults, who may find it difficult to visit the clinic.

Adaptive Optical System for Retina Imaging Approaches Clinic Applications

NASA Astrophysics Data System (ADS)

Ling, N.; Zhang, Y.; Rao, X.; Wang, C.; Hu, Y.; Jiang, W.; Jiang, C.

We presented "A small adaptive optical system on table for human retinal imaging" at the 3rd Workshop on Adaptive Optics for Industry and Medicine. In this system, a 19 element small deformable mirror was used as wavefront correction element. High resolution images of photo receptors and capillaries of human retina were obtained. In recent two years, at the base of this system a new adaptive optical system for human retina imaging has been developed. The wavefront correction element is a newly developed 37 element deformable mirror. Some modifications have been adopted for easy operation. Experiments for different imaging wavelengths and axial positions were conducted. Mosaic pictures of photoreceptors and capillaries were obtained. 100 normal and abnormal eyes of different ages have been inspected.The first report in the world concerning the most detailed capillary distribution images cover ±3° by ± 3° field around the fovea has been demonstrated. Some preliminary very early diagnosis experiment has been tried in laboratory. This system is being planned to move to the hospital for clinic experiments.

Predictive models applied to groundwater level forecasting: a preliminary experience on the alluvial aquifer of the Magra River (Italy).

NASA Astrophysics Data System (ADS)

Brozzo, Gianpiero; Doveri, Marco; Lelli, Matteo; Scozzari, Andrea

2010-05-01

Computer-based decision support systems are getting a growing interest for water managing authorities and water distribution companies. This work discusses a preliminary experience in the application of computational intelligence in a hydrological modeling framework, regarding the study area of the alluvial aquifer of the Magra River (Italy). Two sites in the studied area, corresponding to two distinct groups of wells (Battifollo and Fornola) are managed by the local drinkable water distribution company (ACAM Acque), which serves the area of La Spezia, on the Ligurian coast. Battifollo has 9 wells with a total extraction rate of about 240 liters per second, while Fornola has 44 wells with an extraction rate of about 900 liters per second. Objective of this work is to make use of time series coming from long-term monitoring activities in order to assess the trend of the groundwater level with respect to a set of environmental and exploitation parameters; this is accomplished by the experimentation of a suitable model, eligible to be used as a predictor. This activity moves on from the modeling of the system behavior, based on a set of Input/Output data, in order to characterize it without necessarily a prior knowledge of any deterministic mechanism (system identification). In this context, data series collected by continuous hydrological monitoring instrumentation installed in the studied sites, together with meteorological and water extraction data, have been analyzed in order to assess the applicability and performance of a predictive model of the groundwater level. A mixed approach (both data driven and process-based) has been experimented on the whole dataset relating to the last ten years of continuous monitoring activity. The system identification approach presented here is based on the integration of an adaptive technique based on Artificial Neural Networks (ANNs) and a blind deterministic identification approach. According to this concept, the behavior of the natural system can be partly explained in terms of its impulse response, identified as an arbitrary function, optimally fitted to the behavior observed in the past time series. In the proposed method, the approximation of the natural behavior of the system derives from the decomposition of the excitation signals (input parameters) into sequences of discrete values. Data fed to the ANN are thus pre-processed according to this concept. In the particular case study presented in this work, the proximity of the Magra River mixes the short-term effects of the hydraulic level of the river with the slower rainfall effects that diffusely feed the groundwater system, making the analysis even more challenging. In addition to piezometric levels, also continuous conductivity data series are available for the same period, and have been taken into account separately in this preliminary experience. The availability of the electrical conductivity parameter opens the way to the modeling of the different contributions to the groundwater reservoir, and may also enable the prediction of some water quality features, as discussed in this work. The preliminary analysis of meteorological and hydrologic data sets is discussed in this work, and goes through the following steps: a) description of the dataset, b) description of the model developed, c) model tuning, d) discussion of results and applicability as a predictor.

Preliminary assessment of the interaction of introduced biological agents with biofilms in water distribution systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sinclair, Michael B.; Caldwell, Sara; Jones, Howland D. T.

2005-12-01

Basic research is needed to better understand the potential risk of dangerous biological agents that are unintentionally or intentionally introduced into a water distribution system. We report on our capabilities to conduct such studies and our preliminary investigations. In 2004, the Biofilms Laboratory was initiated for the purpose of conducting applied research related to biofilms with a focus on application, application testing and system-scale research. Capabilities within the laboratory are the ability to grow biofilms formed from known bacteria or biofilms from drinking water. Biofilms can be grown quickly in drip-flow reactors or under conditions more analogous to drinking-water distributionmore » systems in annular reactors. Biofilms can be assessed through standard microbiological techniques (i .e, aerobic plate counts) or with various visualization techniques including epifluorescent and confocal laser scanning microscopy and confocal fluorescence hyperspectral imaging with multivariate analysis. We have demonstrated the ability to grow reproducible Pseudomonas fluorescens biofilms in the annular reactor with plate counts on the order of 10{sup 5} and 10{sup 6} CFU/cm{sup 2}. Stationary phase growth is typically reached 5 to 10 days after inoculation. We have also conducted a series of pathogen-introduction experiments, where we have observed that both polystyrene microspheres and Bacillus cereus (as a surrogate for B. anthracis) stay incorporated in the biofilms for the duration of our experiments, which lasted as long as 36 days. These results indicated that biofilms may act as a safe harbor for bio-pathogens in drinking water systems, making it difficult to decontaminate the systems.« less

Investigation of decolorization of textile wastewater in an anaerobic/aerobic biological activated carbon system (A/A BAC).

PubMed

Pasukphun, N; Vinitnantharat, S; Gheewala, S

2010-04-01

The aim of this study is to investigate the decolorization in anaerobic/aerobic biological activated carbon (A/A BAC) system. The experiment was divided into 2 stages; stage I is batch test for preliminary study of dye removal equilibrium time. The preliminary experiment (stage I) provided the optimal data for experimental design of A/A BAC system in SBR (stage II). Stage II is A/A BAC system imitated Sequencing Batch Reactor (SBR) which consist of 5 main periods; fill, react, settle, draw and idle. React period include anaerobic phase followed by aerobic phase. The BAC main media; Granular Activated Carbon (GAC), Mixed Cultures (MC) and Biological Activated Carbon (BAC) were used for dye and organic substances removal in three different solutions; Desizing Agent Solution (DAS), dye Solution (DS) and Synthetic Textile Wastewater (STW). Results indicate that GAC adsorption plays role in dye removal followed by BAC and MC activities, respectively. In the presence desizing agent, decolorization by MC was improved because desizing agent acts as co-substrates for microorganisms. It was found that 50% of dye removal efficiency was achieved in Fill period by MC. GC/MS analysis was used to identify dye intermediate from decolorization. Dye intermediate containing amine group was found in the solution and on BAC surfaces. The results demonstrated that combination of MC and BAC in the system promotes decolorization and dye intermediate removal. In order to improve dye removal efficiency in an A/A BAC system, replacement of virgin GAC, sufficient co-substrates supply and the appropriate anaerobic: aerobic period should be considered.

A comparison of freezing-damage during isochoric and isobaric freezing of the potato.

PubMed

Lyu, Chenang; Nastase, Gabriel; Ukpai, Gideon; Serban, Alexandru; Rubinsky, Boris

2017-01-01

Freezing is commonly used for food preservation. It is usually done under constant atmospheric pressure (isobaric). While extending the life of the produce, isobaric freezing has detrimental effects. It causes loss of food weight and changes in food quality. Using thermodynamic analysis, we have developed a theoretical model of the process of freezing in a constant volume system (isochoric). The mathematical model suggests that the detrimental effects associated with isobaric freezing may be reduced in an isochoric freezing system. To explore this hypothesis, we performed a preliminary study on the isochoric freezing of a produce with which our group has experience, the potato. Experiments were performed in an isochoric freezing device we designed. The device is robust and has no moving parts. For comparison, we used a geometrically identical isobaric freezing device. Following freezing and thawing, the samples were weighed, examined with colorimetry, and examined with microscopy. It was found that potatoes frozen to -5 °C in an isochoric system experienced no weight loss and limited enzymatic browning. In contrast the -5 °C isobaric frozen potato experienced substantial weight loss and substantial enzymatic browning. Microscopic analysis shows that the structural integrity of the potato is maintained after freezing in the isochoric system and impaired after freezing in the isobaric system. Tissue damage during isobaric freezing is caused by the increase in extracellular osmolality and the mechanical damage by ice crystals. Our thermodynamic analysis predicts that during isochoric freezing the intracellular osmolality remains comparable to the extracellular osmolality and that isochoric systems can be designed to eliminate the mechanical damage by ice. The results of this preliminary study seem to confirm the theoretical predictions. This is a preliminary exploratory study on isochoric freezing of food. We have shown that the quality of a food product preserved by isochoric freezing is better than the quality of food preserved to the same temperature in isobaric conditions. Obviously, more extensive research remains to be done to extend this study to lower freezing temperatures and other food items.

A comparison of freezing-damage during isochoric and isobaric freezing of the potato

PubMed Central

Serban, Alexandru; Rubinsky, Boris

2017-01-01

Background Freezing is commonly used for food preservation. It is usually done under constant atmospheric pressure (isobaric). While extending the life of the produce, isobaric freezing has detrimental effects. It causes loss of food weight and changes in food quality. Using thermodynamic analysis, we have developed a theoretical model of the process of freezing in a constant volume system (isochoric). The mathematical model suggests that the detrimental effects associated with isobaric freezing may be reduced in an isochoric freezing system. To explore this hypothesis, we performed a preliminary study on the isochoric freezing of a produce with which our group has experience, the potato. Method Experiments were performed in an isochoric freezing device we designed. The device is robust and has no moving parts. For comparison, we used a geometrically identical isobaric freezing device. Following freezing and thawing, the samples were weighed, examined with colorimetry, and examined with microscopy. Results It was found that potatoes frozen to −5 °C in an isochoric system experienced no weight loss and limited enzymatic browning. In contrast the −5 °C isobaric frozen potato experienced substantial weight loss and substantial enzymatic browning. Microscopic analysis shows that the structural integrity of the potato is maintained after freezing in the isochoric system and impaired after freezing in the isobaric system. Discussion Tissue damage during isobaric freezing is caused by the increase in extracellular osmolality and the mechanical damage by ice crystals. Our thermodynamic analysis predicts that during isochoric freezing the intracellular osmolality remains comparable to the extracellular osmolality and that isochoric systems can be designed to eliminate the mechanical damage by ice. The results of this preliminary study seem to confirm the theoretical predictions. Conclusion This is a preliminary exploratory study on isochoric freezing of food. We have shown that the quality of a food product preserved by isochoric freezing is better than the quality of food preserved to the same temperature in isobaric conditions. Obviously, more extensive research remains to be done to extend this study to lower freezing temperatures and other food items. PMID:28533970

Development of an intelligent hypertext system for wind tunnel testing

NASA Technical Reports Server (NTRS)

Lo, Ching F.; Shi, George Z.; Steinle, Frank W.; Wu, Y. C. L. Susan; Hoyt, W. Andes

1991-01-01

This paper summarizes the results of a system utilizing artificial intelligence technology to improve the productivity of project engineers who conduct wind tunnel tests. The objective was to create an intelligent hypertext system which integrates a hypertext manual and expert system that stores experts' knowledge and experience. The preliminary (Phase I) effort implemented a prototype IHS module encompassing a portion of the manuals and knowledge used for wind tunnel testing. The effort successfully demonstrated the feasibility of the intelligent hypertext system concept. A module for the internal strain gage balance, implemented on both IBM-PC and Macintosh computers, is presented. A description of the Phase II effort is included.

The 30/20 GHz demonstration system SSUS-D/BSE

NASA Technical Reports Server (NTRS)

1981-01-01

The systems consisting of a 30/20 GHz communication satellite featuring a multiple fixed beam and scanning beam antenna, SS-TDMA, onboard processing and high power TWT's and IMPATT amplifiers, a trunking space-diversity Earth station, a customer premise system (CPS) portable Earth station and a Master Control Station. Hardware, software and personnel are included to build and launch one satellite and to carry on a two year experimentation and demonstration period of advanced Ka-band systems concepts and technology. Included are first level plans identifying all tasks, a schedule for system development and an assessment of critical technology and risk and a preliminary experiments plan.

Preliminary Results with the Design and Implementation of an Academic Management Information System

PubMed Central

Evans, Steven

1984-01-01

This paper provides an overview of aspects of an academic management information system (AMIS) at Creighton University's Academic Health Center. This report summarizes briefly some of the features of the system, our experiences in implementing it, some of the reactions from our academic community to a “foreign” body (and our attempts to reduce the rejection mechanism), as well as successes to date. Lastly we describe steps underway to expand the system into a full-fledged example of the system as envisioned in the Matheson and Cooper report on “Academic Information in the Academic Health Sciences Center.”

An Overview of NASA Automotive Component Reliability Studies

NASA Technical Reports Server (NTRS)

Sampson, Michael J.

2016-01-01

The results of NASAs studies into the appropriateness of using US Automotive electronic parts in NASA spaceflight systems will be presented. The first part of the presentation provides an overview of the United States Automotive Electronics Councils AECQ standardization program, the second part provides a summary of the results of NASAs procurement and testing experiences and other lessons learned along with preliminary test results.

An Overview Of NASA Automotive Component Reliability Studies

NASA Technical Reports Server (NTRS)

Sampson, Michael J.

2016-01-01

The results of NASAs studies into the appropriateness of using US Automotive electronic parts in NASA spaceflight systems will be presented. The first part of the presentation provides an overview of the United States Automotive Electronics Councils AECQ standardization program, the second part provides a summary of the results of NASAs procurement and testing experiences and other lessons learned along with preliminary test results.

Large-area sheet task advanced dendritic web growth development

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

1982-01-01

The thermal stress model was used to generate the design of a low stress lid and shield configuration, which was fabricated and tested experimentally. In preliminary tests, the New Experimental Web Growth Facility performed as designed, producing web on the first run. These experiments suggested desirable design modifications in the melt level sensing system to improve further its performance, and these are being implemented.

Kevlar Vest Protection Against Blast Overpressure Brain Injury: Systemic Contributions to Injury Etiology

DTIC Science & Technology

2014-11-01

GF, Moss WC, Cleveland RO, Tanzi RE, Stanton PK, McKee AC. Chronic traumatic encephalopathy in blast-exposed military veterans and a blast... traumatic brain injury (bTBI) is largely undefined. Along with reducing mortality, in preliminary experiments Kevlar vests significantly protected...mitigation strategies. 15. SUBJECT TERMS Traumatic Brain Injury (TBI), Kevlar Vests, Neuroprotection 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF

Preliminary Flight Results of the Microelectronics and Photonics Test Bed: NASA DR1773 Fiber Optic Data Bus Experiment

NASA Technical Reports Server (NTRS)

Jackson, George L.; LaBel, Kenneth A.; Marshall, Cheryl; Barth, Janet; Seidleck, Christina; Marshall, Paul

1998-01-01

NASA Goddard Spare Flight Center's (GSFC) Dual Rate 1773 (DR1773) Experiment on the Microelectronic and Photonic Test Bed (MPTB) has provided valuable information on the performance of the AS 1773 fiber optic data bus in the space radiation environment. Correlation of preliminary experiment data to ground based radiation test results show the AS 1773 bus is employable in future spacecraft applications requiring radiation tolerant communication links.

Multimode electromagnetic target discriminator: preliminary data results

NASA Astrophysics Data System (ADS)

Black, Christopher J.; McMichael, Ian T.; Nelson, Carl V.

2004-09-01

This paper describes the Multi-mode Electromagnetic Target Discriminator (METD) sensor and presents preliminary results from recent field experiments. The METD sensor was developed for the US Army RDECOM NVESD by The Johns Hopkins University Applied Physics Laboratory. The METD, based on the technology of the previously developed Electromagnetic Target Discriminator (ETD), is a spatial scanning electromagnetic induction (EMI) sensor that uses both the time-domain (TD) and the frequency-domain (FD) for target detection and classification. Data is collected with a custom data acquisition system and wirelessly transmitted to a base computer. We show that the METD has a high signal-to-noise ratio (SNR), the ability to detect voids created by plastic anti-tank (AT) mines, and is practical for near real-time data processing.

Segmental transport after unreamed intramedullary nailing. Preliminary report of a "Monorail" system.

PubMed

Raschke, M J; Mann, J W; Oedekoven, G; Claudi, B F

1992-09-01

The Ilizarov method of segmental bone transport has been shown to be an alternative to more conventional treatments of posttraumatic bony defects. After extensive clinical experience with the unreamed tibial nail in open fractures up to Grade IIIb, a new monorail fixation system for callus distraction and segmental bone transport was devised. This Monorail system is composed of an unreamed intramedullary (IM) nail and a unilateral AO distraction device. The new fixation method and the preliminary clinical experience are reported here. Four patients who previously sustained Grades II-IIIb open tibial fractures had an average bony defect of 9 cm. Two patients had previous bony infections. All patients had had serial debridements and myocutaneous flaps were required in three patients. An unreamed IM nail was inserted, and the transport device was applied. After an osteotomy, segmental transport was carried out until docking was achieved. The external fixator was removed after interlocking of the transported segment. The mean duration of external fixation was 17.9 days/cm and the mean period until roentgenographic consolidation of the distraction and nonunion site was 41.2 days/cm. There were two pin-tract infections but no IM infections. One nail broke after osseous consolidation of the regenerate at the distal interlocking site and required exchange. The goal of transport was achieved in all cases without angular or rotational deformity or length discrepancy. There were no neurovascular injuries.

Aerosols and polar stratospheric clouds measurements during the EASOE campaign

NASA Technical Reports Server (NTRS)

Haner, D.; Godin, S.; Megie, G.; David, C.; Mitev, V.

1992-01-01

Preliminary results of observations performed using two different lidar systems during the EASOE (European Arctic Stratospheric Ozone Experiment), which has taken place in the winter of 1991-1992 in the northern hemisphere lattitude regions, are presented. The first system is a ground based multiwavelength lidar intended to perform measurements of the ozone vertical distribution in the 5 km to 40 km altitude range. It was located in Sodankyla (67 degrees N, 27 degrees E) as part of the ELSA experiment. The objectives of the ELSA cooperative project is to study the relation between polar stratospheric cloud events and ozone depletion with high vertical resolution and temporal continuity, and the evolution of the ozone distribution in relation to the position of the polar vortex. The second system is an airborne backscatter lidar (Leandre) which allows for the study of the 3-D structure and the optical properties of polar stratospheric clouds. The Leandre instrument is a dual-polarization lidar system, emitting at 532 nm, which allows for the determination of the type of clouds observed, according to the usual classification of polar stratospheric clouds. More than 60 hours of flight were performed in Dec. 1991, and Jan. and Feb. 1992 in Kiruna, Sweden. The operation of the Leandre instrument has led to the observation of the short scale variability of the Pinatubo volcanic cloud in the high latitude regions and to several episodes of polar stratospheric clouds. Preliminary analysis of the data is presented.

30-kW class Arcjet Advanced Technology Transition Demonstration (ATTD) flight experiment diagnostic package

NASA Astrophysics Data System (ADS)

Kriebel, M. M.; Stevens, N. J.

1992-07-01

TRW, Rocket Research Co and Defense Systems Inc are developing a space qualified 30-kW class arcjet flight unit as a part of the Arcjet ATTD program. During space operation the package will measure plume deposition and contamination, electromagnetic interference, thermal radiation, arcjet thruster performance, and plume heating in order to quantify arcjet operational interactions. The Electric Propulsion Space Experiment (ESEX) diagnostic package is described. The goals of ESEX are the demonstration of a high powered arcjet performance and the measurement of potential arcjet-spacecraft interactions which cannot be determined in ground facilities. Arcjet performance, plume characterization, thermal radiation flux and the electromagnetic interference (EMI) experiment as well as experiment operations with a preliminary operations plan are presented.

A primary care-public health partnership addressing homelessness, serious mental illness, and health disparities.

PubMed

Weinstein, Lara Carson; Lanoue, Marianna D; Plumb, James D; King, Hannah; Stein, Brianna; Tsemberis, Sam

2013-01-01

People with histories of homelessness and serious mental illness experience profound health disparities. Housing First is an evidenced-based practice that is working to end homelessness for these individuals through a combination of permanent housing and community-based supports. The Jefferson Department of Family and Community Medicine and a Housing First agency, Pathways to Housing-PA, has formed a partnership to address multiple levels of health care needs for this group. We present a preliminary program evaluation of this partnership using the framework of the patient-centered medical home and the "10 Essential Public Health Services." Preliminary program evaluation results suggest that this partnership is evolving to function as an integrated person-centered health home and an effective local public health monitoring system. The Pathways to Housing-PA/Jefferson Department of Family and Community Medicine partnership represents a community of solution, and multiple measures provide preliminary evidence that this model is feasible and can address the "grand challenges" of integrated community health services.

Small helium-cooled infrared telescope experiment for Spacelab-2 (IRT)

NASA Technical Reports Server (NTRS)

Fazio, Giovanni G.

1990-01-01

The Infrared Telescope (IRT) experiment, flown on Spacelab-2, was used to make infrared measurements between 2 and 120 microns. The objectives were multidisciplinary in nature with astrophysical goals of mapping the diffuse cosmic emission and extended infrared sources and technical goals of measuring the induced Shuttle environment, studying properties of superfluid helium in space, and testing various infrared telescope system designs. Astrophysically, new data were obtained on the structure of the Galaxy at near-infrared wavelengths. A summary of the large scale diffuse near-infrared observations of the Galaxy by the IRT is presented, as well as a summary of the preliminary results obtained from this data on the structure of the galactic disk and bulge. The importance of combining CO and near-infrared maps of similar resolution to determine a 3-D model of galactic extinction is demonstrated. The IRT data are used, in conjunction with a proposed galactic model, to make preliminary measurements of the global scale parameters of the Galaxy. During the mission substantial amounts of data were obtained concerning the induced Shuttle environment. An experiment was also performed to measure spacecraft glow in the IR.

A pilot study using laser-based technique for non-invasive diagnostics of hypertensive conditions in mice

NASA Astrophysics Data System (ADS)

Litvinova, Karina S.; Ahmad, Shakil; Wang, Keqing; Rafailov, Ilya E.; Sokolovski, Sergei G.; Zhang, Lin; Rafailov, Edik U.; Ahmed, Asif

2016-02-01

Endothelial dysfunction is directly linked to preeclampsia, a maternal hypertensive condition that is life threating for both the mother and the baby. Epidemiological studies show that women with a history of pre-eclampsia have an elevated risk for cardiovascular disease. Here we report a new non-invasive diagnostic test for preeclampsia in mice that allows us to non-invasively assess the condition of the animals during the experiment and treatment in established models of preeclampsia. A laser-based multifunctional diagnostics system (LAKK-M) was chosen to carry out non-invasive analysis of multiple parameters. The device was used to simultaneously record the microcirculatory blood flow and oxygen saturation, as well as fluorescence levels of endogenous fluorophores. Preliminary experiments were conducted on adenoviral (Ad-)- mediated overexpression of sFlt-1 (Ad-sFlt-1) to mimic preeclampsialike symptoms in mice. The recorded data displayed the ability of the LAKK-M diagnostics device to detect significant differences in perfusion measurements between the control and Ad-sFlt-1 treatment. Preliminary results provide a potential avenue to employ these diagnostics technology to monitor and aid in maintaining control of live animal conditions throughout the experiment and treatment.

Preliminary design report: Babcock and Wilcox BR-100 100-ton rail/barge spent fuel shipping cask

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1990-02-01

The purpose of this document is to provide information on burnup credit as applied to the preliminary design of the BR-100 shipping cask. There is a brief description of the preliminary basket design and the features used to maintain a critically safe system. Following the basket description is a discussion of various criticality analyses used to evaluate burnup credit. The results from these analyses are then reviewed in the perspective of fuel burnups expected to be shipped to either the final repository or a Monitored Retrievable Storage (MRS) facility. The hurdles to employing burnup credit in the certification of anymore » cask are then outlines and reviewed. the last section gives conclusions reached as to burnup credit for the BR-100 cask, based on our analyses and experience. All information in this study refers to the cask configured to transport PWR fuel. Boiling Water Reactor (BWR) fuel satisfies the criticality requirements so that burnup credit is not needed. All calculations generated in the preparation of this report were based upon the preliminary design which will be optimized during the final design. 8 refs., 19 figs., 16 tabs.« less

Experiences in teleoperation of land vehicles

NASA Technical Reports Server (NTRS)

Mcgovern, Douglas E.

1989-01-01

Teleoperation of land vehicles allows the removal of the operator from the vehicle to a remote location. This can greatly increase operator safety and comfort in applications such as security patrol or military combat. The cost includes system complexity and reduced system performance. All feedback on vehicle performance and on environmental conditions must pass through sensors, a communications channel, and displays. In particular, this requires vision to be transmitted by close-circuit television with a consequent degradation of information content. Vehicular teleoperation, as a result, places severe demands on the operator. Teleoperated land vehicles have been built and tested by many organizations, including Sandia National Laboratories (SNL). The SNL fleet presently includes eight vehicles of varying capability. These vehicles have been operated using different types of controls, displays, and visual systems. Experimentation studying the effects of vision system characteristics on off-road, remote driving was performed for conditions of fixed camera versus steering-coupled camera and of color versus black and white video display. Additionally, much experience was gained through system demonstrations and hardware development trials. The preliminary experimental findings and the results of the accumulated operational experience are discussed.

Teaching Note--Description and Preliminary Evaluation of a Modified College Experience for Adults with Intellectual and Developmental Disabilities

ERIC Educational Resources Information Center

Remis, Kimberly; Moore, Crystal Dea; Pichardo, Julia; Rosario, Zuliany; Moore, Jeffrey Palmer

2017-01-01

This article describes the implementation and preliminary evaluation of a modified college experience for adults with intellectual and developmental disabilities (IDD) at a small liberal arts college. To increase social work students' interest in working with this population and access of people with IDD to higher education, Bridges to Skidmore…

Foundations of a query and simulation system for the modeling of biochemical and biological processes.

PubMed

Antoniotti, M; Park, F; Policriti, A; Ugel, N; Mishra, B

2003-01-01

The analysis of large amounts of data, produced as (numerical) traces of in vivo, in vitro and in silico experiments, has become a central activity for many biologists and biochemists. Recent advances in the mathematical modeling and computation of biochemical systems have moreover increased the prominence of in silico experiments; such experiments typically involve the simulation of sets of Differential Algebraic Equations (DAE), e.g., Generalized Mass Action systems (GMA) and S-systems. In this paper we reason about the necessary theoretical and pragmatic foundations for a query and simulation system capable of analyzing large amounts of such trace data. To this end, we propose to combine in a novel way several well-known tools from numerical analysis (approximation theory), temporal logic and verification, and visualization. The result is a preliminary prototype system: simpathica/xssys. When dealing with simulation data simpathica/xssys exploits the special structure of the underlying DAE, and reduces the search space in an efficient way so as to facilitate any queries about the traces. The proposed system is designed to give the user possibility to systematically analyze and simultaneously query different possible timed evolutions of the modeled system.

Direct-Drive Gas-Cooled Reactor Power System: Concept and Preliminary Testing

NASA Technical Reports Server (NTRS)

Wright, S. A.; Lipinski, R. J.; Godfroy, T. J.; Bragg-Sitton, S. M.; VanDyke, M. K.

2002-01-01

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet- sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrically heated testing of simulated reactor components.

Customized Interactive Robotic Treatment for Stroke: EMG-Triggered Therapy

PubMed Central

Dipietro, Laura; Ferraro, Mark; Palazzolo, Jerome Joseph; Krebs, Hermano Igo; Volpe, Bruce T.; Hogan, Neville

2009-01-01

A system for electromyographic (EMG) triggering of robot-assisted therapy (dubbed the EMG game) for stroke patients is presented. The onset of a patient’s attempt to move is detected by monitoring EMG in selected muscles, whereupon the robot assists her or him to perform point-to-point movements in a horizontal plane. Besides delivering customized robot-assisted therapy, the system can record signals that may be useful to better understand the process of recovery from stroke. Preliminary experiments aimed at testing the proposed system and gaining insight into the potential of EMG-triggered, robot-assisted therapy are reported. PMID:16200756

7 CFR 1942.20 - Community Facility Guides.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... (7) Guide 7—Preliminary Engineering Report Water Facility. (8) Guide 8—Preliminary Engineering Report Sewerage Systems. (9) Guide 9—Preliminary Engineering Report Solid Waste Disposal Systems. (10) Guide 10—Preliminary Engineering Report Storm Waste-Water Disposal. (11) Guide 11—Daily Inspection Report. (12) Guide...

Analytical and Radio-Histo-Chemical Experiments of Plants and Tissue Culture Cells Treated with Lunar and Terrestrial Materials

NASA Technical Reports Server (NTRS)

Halliwell, R. S.

1973-01-01

The nature and mechanisms of the apparent simulation of growth originally observed in plants growing in contact with lunar soil during the Apollo project quarantine are examined. Preliminary experiments employing neutron activated lunar soil indicate uptake of a few elements by plants. It was found that while the preliminary neutron activation technique allowed demonstration of uptake of minerals it presented numerous disadvantages for use in critical experiments directed at elucidating possible mechanisms of stimulation.

Preliminary design of flight hardware for two-phase fluid research

NASA Technical Reports Server (NTRS)

Hustvedt, D. C.; Oonk, R. L.

1982-01-01

This study defined the preliminary designs of flight software for the Space Shuttle Orbiter for three two-phase fluid research experiments: (1) liquid reorientation - to study the motion of liquid in tanks subjected to small accelerations; (2) pool boiling - to study low-gravity boiling from horizontal cylinders; and (3) flow boiling - to study low-gravity forced flow boiling heat transfer and flow phenomena in a heated horizontal tube. The study consisted of eight major tasks: reassessment of the existing experiment designs, assessment of the Spacelab facility approach, assessment of the individual carry-on approach, selection of the preferred approach, preliminary design of flight hardware, safety analysis, preparation of a development plan, estimates of detailed design, fabrication and ground testing costs. The most cost effective design approach for the experiments is individual carry-ons in the Orbiter middeck. The experiments were designed to fit into one or two middeck lockers. Development schedules for the detailed design, fabrication and ground testing ranged from 15 1/2 to 18 months. Minimum costs (in 1981 dollars) ranged from $463K for the liquid reorientation experiment to $998K for the pool boiling experiment.

Atomic pair distribution function at the Brazilian Synchrotron Light Laboratory: application to the Pb 1–x La xZr 0.40Ti 0.60O 3 ferroelectric system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saleta, M. E.; Eleotério, M.; Mesquita, A.

2017-07-29

This work reports the setting up of the X-ray diffraction and spectroscopy beamline at the Brazilian Synchrotron Light Laboratory for performing total scattering experiments to be analyzed by atomic pair distribution function (PDF) studies. The results of a PDF refinement for Al 2O 3 standard are presented and compared with data acquired at a beamline of the Advanced Photon Source, where it is common to perform this type of experiment. A preliminary characterization of the Pb 1–xLa xZr 0.40Ti 0.60O 3 ferroelectric system, withx= 0.11, 0.12 and 0.15, is also shown.

Design and Deployment of a Multichroic Polarimeter Array on the Atacama Cosmology Telescope

NASA Technical Reports Server (NTRS)

Datta, R.; Austermann, J.; Beall, J. A.; Becker, D.; Coughlin, K. P.; Duff, S. M.; Gallardo, P.A.; Grace, E.; Hasselfield, M.; Henderson, S. W.;

Early experiences building a software quality prediction model

NASA Technical Reports Server (NTRS)

Agresti, W. W.; Evanco, W. M.; Smith, M. C.

1990-01-01

Early experiences building a software quality prediction model are discussed. The overall research objective is to establish a capability to project a software system's quality from an analysis of its design. The technical approach is to build multivariate models for estimating reliability and maintainability. Data from 21 Ada subsystems were analyzed to test hypotheses about various design structures leading to failure-prone or unmaintainable systems. Current design variables highlight the interconnectivity and visibility of compilation units. Other model variables provide for the effects of reusability and software changes. Reported results are preliminary because additional project data is being obtained and new hypotheses are being developed and tested. Current multivariate regression models are encouraging, explaining 60 to 80 percent of the variation in error density of the subsystems.

Design and Deployment of a Multichroic Polarimeter Array on the Atacama Cosmology Telescope

NASA Astrophysics Data System (ADS)

Datta, R.; Austermann, J.; Beall, J. A.; Becker, D.; Coughlin, K. P.; Duff, S. M.; Gallardo, P. A.; Grace, E.; Hasselfield, M.; Henderson, S. W.; Hilton, G. C.; Ho, S. P.; Hubmayr, J.; Koopman, B. J.; Lanen, J. V.; Li, D.; McMahon, J.; Munson, C. D.; Nati, F.; Niemack, M. D.; Page, L.; Pappas, C. G.; Salatino, M.; Schmitt, B. L.; Schillaci, A.; Simon, S. M.; Staggs, S. T.; Stevens, J. R.; Vavagiakis, E. M.; Ward, J. T.; Wollack, E. J.

2016-08-01

We present the design and the preliminary on-sky performance with respect to beams and passbands of a multichroic polarimeter array covering the 90 and 146 GHz cosmic microwave background bands and its enabling broad-band optical system recently deployed on the Atacama Cosmology Telescope (ACT). The constituent pixels are feedhorn-coupled multichroic polarimeters fabricated at NIST. This array is coupled to the ACT telescope via a set of three silicon lenses incorporating novel broad-band metamaterial anti-reflection coatings. This receiver represents the first multichroic detector array deployed for a CMB experiment and paves the way for the extensive use of multichroic detectors and broad-band optical systems in the next generation of CMB experiments.

Verification and Validation of Requirements on the CEV Parachute Assembly System Using Design of Experiments

NASA Technical Reports Server (NTRS)

Schulte, Peter Z.; Moore, James W.

2011-01-01

The Crew Exploration Vehicle Parachute Assembly System (CPAS) project conducts computer simulations to verify that flight performance requirements on parachute loads and terminal rate of descent are met. Design of Experiments (DoE) provides a systematic method for variation of simulation input parameters. When implemented and interpreted correctly, a DoE study of parachute simulation tools indicates values and combinations of parameters that may cause requirement limits to be violated. This paper describes one implementation of DoE that is currently being developed by CPAS, explains how DoE results can be interpreted, and presents the results of several preliminary studies. The potential uses of DoE to validate parachute simulation models and verify requirements are also explored.

GAS payload no. G-025: Study of liquid sloshing behaviour in microgravity

NASA Technical Reports Server (NTRS)

Gilbert, C. R.

1986-01-01

The Get Away Special (GAS) G-025, which flew on shuttle Mission 51-G, examined the behavior of a liquid in a tank under microgravity conditions. The experiment is representative of phenomena occurring in satellite tanks with liquid propellants. A reference fluid in a hemispherical model tank will be subjected to linear acceleration inputs of known levels and frequencies, and the dynamic response of the tank liquid system was recorded. Preliminary analysis of the flight data indicates that the experiment functioned perfectly. The results will validate and refine mathematical models describing the dynamic characteristics of tank-fluid systems. This will in turn support the development of future spacecraft tanks, in particular the design of propellant management devices for surface tension tanks.

Preliminary Observing System Simulation Experiments for Doppler Wind Lidars Deployed on the International Space Station

NASA Technical Reports Server (NTRS)

Kemp, E.; Jacob, J.; Rosenberg, R.; Jusem, J. C.; Emmitt, G. D.; Wood, S.; Greco, L. P.; Riishojgaard, L. P.; Masutani, M.; Ma, Z.;

Crystal growth from the vapor phase experiment MA-085

NASA Technical Reports Server (NTRS)

Wiedemeir, H.; Sadeek, H.; Klaessig, F. C.; Norek, M.

1976-01-01

Three vapor transport experiments on multicomponent systems were performed during the Apollo Soyuz mission to determine the effects of microgravity forces on crystal morphology and mass transport rates. The mixed systems used germanium selenide, tellurium, germanium tetraiodide (transport agent), germanium monosulfide, germanium tetrachloride (transport agent), and argon (inert atmosphere). The materials were enclosed in evacuated sealed ampoules of fused silica and were transported in a temperature gradient of the multipurpose electric furnace onboard the Apollo Soyuz spacecraft. Preliminary evaluation of 2 systems shows improved quality of space grown crystals in terms of growth morphology and bulk perfection. This conclusion is based on a direct comparison of space grown and ground based crystals by means of X-ray diffraction, microscopic, and chemical etching techniques. The observation of greater mass transport rates than predicted for a microgravity environment by existing vapor transport models indicates the existence of nongravity caused transport effects in a reactive solid/gas phase system.

FEMME: a precursor experiment for the evaluation of bioregenerative life support systems

NASA Astrophysics Data System (ADS)

Paille, Ch.; Albiol, J.; Curwy, R.; Lasseur, Ch.; Godia, F.

2000-04-01

In long term manned space missions, oxygen, water and food supplies are a critical issue. Bioregenerative systems, and among them those relying on microbial processes, represent one of the most promising alternatives. Studies of these systems from the engineering point of view, requires the development of mathematical models and their validation with small scale experimental systems (breadboards, pilot plants, etc.). Usually, these studies do not take into account the effects of space environment (i.e. reduced gravity or microgravity, radiation, direct sunlight, temperature, etc …). Despite several scientific experiments, intending to qualify such effects, only few quantitative results are available. In this paper, the possibility of an autonomous off-board experiment, named the First Extraterrestrial Man Made Ecosystem, is investigated. The experiment is based on a very simplified ecosystem consisting in a photoautotrophic compartment and a heterotrophic one, linked by their gas phase. According to its biological concept, this experiment should provide data on microbial growth kinetics in space, and the effects of radiation and gravity. It has been conceived as an entirely automatic device. Its design involves several technological concepts such as thermal control, the use of direct sunlight and radiation shielding. This work is done under the framework of ESA biological life support systems research program. The aim of this document is to provide a preliminary concept of the experiment.

Ascending and Descending in Virtual Reality: Simple and Safe System Using Passive Haptics.

PubMed

Nagao, Ryohei; Matsumoto, Keigo; Narumi, Takuji; Tanikawa, Tomohiro; Hirose, Michitaka

2018-04-01

This paper presents a novel interactive system that provides users with virtual reality (VR) experiences, wherein users feel as if they are ascending/descending stairs through passive haptic feedback. The passive haptic stimuli are provided by small bumps under the feet of users; these stimuli are provided to represent the edges of the stairs in the virtual environment. The visual stimuli of the stairs and shoes, provided by head-mounted displays, evoke a visuo-haptic interaction that modifies a user's perception of the floor shape. Our system enables users to experience all types of stairs, such as half-turn and spiral stairs, in a VR setting. We conducted a preliminary user study and two experiments to evaluate the proposed technique. The preliminary user study investigated the effectiveness of the basic idea associated with the proposed technique for the case of a user ascending stairs. The results demonstrated that the passive haptic feedback produced by the small bumps enhanced the user's feeling of presence and sense of ascending. We subsequently performed an experiment to investigate an improved viewpoint manipulation method and the interaction of the manipulation and haptics for both the ascending and descending cases. The experimental results demonstrated that the participants had a feeling of presence and felt a steep stair gradient under the condition of haptic feedback and viewpoint manipulation based on the characteristics of actual stair walking data. However, these results also indicated that the proposed system may not be as effective in providing a sense of descending stairs without an optimization of the haptic stimuli. We then redesigned the shape of the small bumps, and evaluated the design in a second experiment. The results indicated that the best shape to present haptic stimuli is a right triangle cross section in both the ascending and descending cases. Although it is necessary to install small protrusions in the determined direction, by using this optimized shape the users feeling of presence of the stairs and the sensation of walking up and down was enhanced.

Surfactant-based critical phenomena in microgravity

NASA Technical Reports Server (NTRS)

Kaler, Eric W.; Paulaitis, Michael E.

1994-01-01

The objective of this research project is to characterize by experiment and theoretically both the kinetics of phase separation and the metastable structures produced during phase separation in a microgravity environment. The particular systems we are currently studying are mixtures of water, nonionic surfactants, and compressible supercritical fluids at temperatures and pressures where the coexisting liquid phases have equal densities (isopycnic phases). In this report, we describe experiments to locate equilibrium isopycnic phases and to determine the 'local' phase behavior and critical phenomena at nearby conditions of temperature, pressure, and composition. In addition, we report the results of preliminary small angle neutron scattering (SANS) experiments to characterize microstructures that exist in these mixtures at different fluid densities.

Preliminary results on the NPE experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cansi, Y.; Crusem, R.; Masso, J.P.

1994-12-31

Answering to an invitation of the DOE, the Laboratoire de Detection et de Geophysique du Commissariat a I`Energie Atomique (CEA/LDG) participated to the seismic measurements associated with the NPE Experiment organized by the DOE at the Nevada Test Site. Our main motivations were: to evaluate and compare the capabilities of detection and location of the two types of the so-called alpha stations which composed the Experimental International Seismic System (i.e.: the composite stations and the miniarrays) and this in a regional environnement, to calibrate these stations with a chemical blast of known energy within a given propagation structure.

Space station experiment definition: Advanced power system test bed

NASA Technical Reports Server (NTRS)

Pollard, H. E.; Neff, R. E.

1986-01-01

A conceptual design for an advanced photovoltaic power system test bed was provided and the requirements for advanced photovoltaic power system experiments better defined. Results of this study will be used in the design efforts conducted in phase B and phase C/D of the space station program so that the test bed capabilities will be responsive to user needs. Critical PV and energy storage technologies were identified and inputs were received from the idustry (government and commercial, U.S. and international) which identified experimental requirements. These inputs were used to develop a number of different conceptual designs. Pros and cons of each were discussed and a strawman candidate identified. A preliminary evolutionary plan, which included necessary precursor activities, was established and cost estimates presented which would allow for a successful implementation to the space station in the 1994 time frame.

The NASA Electronic Parts and Packaging (NEPP) Program: NEPP Overview - Automotive Electronics

NASA Technical Reports Server (NTRS)

LaBel, Kenneth A.; Sampson, Michael J.

2016-01-01

The results of NASAs studies into the appropriateness of using U.S. Automotive electronic parts in NASA spaceflight systems will be presented. The first part of the presentation provides an overview of the United States Automotive Electronics Council's AECQ standardization program, the second part provides a summary of the results of NASA's procurement and testing experiences and other lessons learned along with preliminary test results.

Optimization of Porous Pellets for Phosphate Recovery ...

EPA Pesticide Factsheets

The poster presents the preliminary adsorption experiment showing that phosphate concentration is decreasing over time as well as presenting the kinetics models that best fit the data collected over 25 days. The purpose of this project is to find a better material for adsorption of phosphate from water treatment facilities. The material is made into pellets which allow for adsorption and are easier to remove from the system when capacity is reached.

A new confined high pressure rotary shear apparatus: preliminary results

NASA Astrophysics Data System (ADS)

Faulkner, D.; Coughlan, G.; Bedford, J. D.

2017-12-01

The frictional properties of fault zone materials, and their evolution during slip, are of paramount importance for determining the earthquake mechanics of large tectonic faults. Friction is a parameter that is difficult to determine from seismological methods so much of our understanding comes from experiment. Rotary shear apparatuses have been widely used in experimental studies to elucidate the frictional properties of faults under realistic earthquake slip velocities (0.1-10 m/s) and displacements (>20 m). However one technical limitation of rotary shear experiments at seismic slip rates has been the lack of confinement. This has led to a limit on the normal stress (due to the strength of the forcing blocks) and also a lack of control of measurements of the pore fluid pressure. Here we present the first preliminary results from a rotary shear apparatus that has been developed to attempt to address this issue. The new fully confined ring shear apparatus has a fast-acting servo-hydraulic confining pressure system of up to 200 MPa and a servo-controlled upstream and downstream pore pressure system of up to 200 MPa. Displacement rates of 0.01μ/s to 2 m/s can be achieved. Fault gouge samples can therefore be sheared at earthquake speed whilst being subject to pressures typically associated with the depth of earthquake nucleation.

Smart Textile Based on Fiber Bragg Grating Sensors for Respiratory Monitoring: Design and Preliminary Trials

PubMed Central

Ciocchetti, Marco; Massaroni, Carlo; Saccomandi, Paola; Caponero, Michele A.; Polimadei, Andrea; Formica, Domenico; Schena, Emiliano

2015-01-01

Continuous respiratory monitoring is important to assess adequate ventilation. We present a fiber optic-based smart textile for respiratory monitoring able to work during Magnetic Resonance (MR) examinations. The system is based on the conversion of chest wall movements into strain of two fiber Bragg grating (FBG) sensors, placed on the upper thorax (UT). FBGs are glued on the textile by an adhesive silicon rubber. To increase the system sensitivity, the FBGs positioning was led by preliminary experiments performed using an optoelectronic system: FBGs placed on the chest surface experienced the largest strain during breathing. System performances, in terms of respiratory period (TR), duration of inspiratory (TI) and expiratory (TE) phases, as well as left and right UT volumes, were assessed on four healthy volunteers. The comparison of results obtained by the proposed system and an optoelectronic plethysmography highlights the high accuracy in the estimation of TR, TI, and TE: Bland-Altman analysis shows mean of difference values lower than 0.045 s, 0.33 s, and 0.35 s for TR, TI, and TE, respectively. The mean difference of UT volumes between the two systems is about 8.3%. The promising results foster further development of the system to allow routine use during MR examinations. PMID:26389961

Preliminary design study for an atomospheric science facility

NASA Technical Reports Server (NTRS)

Hutchison, R.

1972-01-01

The activities and results of the Atmospheric Science Facility preliminary design study are reported. The objectives of the study were to define the scientific goals, to determine the range of experiment types, and to develop the preliminary instrument design requirements for a reusable, general purpose, optical research facility for investigating the earth's atmosphere from a space shuttle orbital vehicle.

Performance characterization of water recovery and water quality from chemical/organic waste products

NASA Technical Reports Server (NTRS)

Moses, W. M.; Rogers, T. D.; Chowdhury, H.; Cullingford, H. S.

1989-01-01

The water reclamation subsystems currently being evaluated for the Space Shuttle Freedom are briefly reviewed with emphasis on a waste water management system capable of processing wastes containing high concentrations of organic/inorganic materials. The process combines low temperature/pressure to vaporize water with high temperature catalytic oxidation to decompose volatile organics. The reclaimed water is of potable quality and has high potential for maintenance under sterile conditions. Results from preliminary experiments and modifications in process and equipment required to control reliability and repeatability of system operation are presented.

["Soiuz-Apollo" experimental flight. Preliminary results of medicobiological studies, carried out during the flight of "Soiuz-19" spaceship].

PubMed

Vorob'ev, E I; Gazenko, O G; Gurovskiĭ, N N; Nefedov, Iu G; Egorov, B B

1976-01-01

The paper presents brief information on the Apollo-Soyuz test mission, its program biomedical investigations to be carried out in flight and specific medical aspects. It discusses the main tasks of the joint US-USSR experiments and Soviet experiments. It gives and analyzes preliminary results of medical monitoring and postflight examinations of the crew members.

A research experiment on facilitation and formation of joint research and development programs between government, industry, and universities: Overview, preliminary findings, and observations

NASA Technical Reports Server (NTRS)

Shariq, Syed Z.

1992-01-01

Presented is an overview of an experiment to explore the free-market approach to public-private collaboration through the development and implementation of a joint venture mechanism to enable formation of R&D projects between government, industry and academia. Some preliminary results related to time-to-commercialization and economic competitiveness are discussed.

Laboratory Measurements of the Sound Generated by Breaking Waves

DTIC Science & Technology

1991-12-01

these techniques have not yet proven effective for studying the dynamics of breaking. The primary motivation for the research 3 presented in this...experiments described in this thesis were motivated by the fact that these preliminary experiments described above demonstrated that the simple I...1991. The research was motivated by the fact that preliminary measurements by Melville, Loewen, Felizardo, Jessup and Buckingham (1988) demonstrated

Combined Numerical/Analytical Perturbation Solutions of the Navier-Stokes Equations for Aerodynamic (Ejector Nozzle) Flows

NASA Technical Reports Server (NTRS)

DeChant, Lawrence J.

1997-01-01

In spite of the rapid advances in both scalar and parallel computational tools, the large number and breadth of variables involved in aerodynamic systems make the use of parabolized or even boundary layer fluid flow models impractical for both preliminary design and inverse design problems. Given this restriction, we have concluded that reduced or approximate models are an important family of tools for design purposes. This study of a combined perturbation/numerical modeling methodology with an application to ejector-mixer nozzles (shown schematically in the following figure) is nearing completion. The work is being funded by a grant from the NASA Lewis Research Center to Texas A&M University. These ejector-mixer nozzle models are designed to be of use to the High Speed Civil Transport Program and may be adopted by both NASA and industry. A computer code incorporating the ejector-mixer models is under development. This code, the Differential Reduced Ejector/Mixer Analysis (DREA), can be run fast enough to be used as a subroutine or to be called by a design optimization routine. Simplified conservation equations--x-momentum, energy, and mass conservation--are used to define the model. Unlike other preliminary design models, DREA requires minimal empirical input and includes vortical mixing and a fully compressible formulation among other features. DREA is being validated by comparing it with results obtained from open literature and proprietary industry data. Preliminary results for a subsonic ejector and a supersonic ejector are shown. In addition, dedicated experiments have been performed at Texas A&M. These experiments use a hydraulic/gas flow analog to provide information about the inviscid mixing interface structure. Final validation and documentation of this work is expected by May of 1997. However, preliminary versions of DREA can be expected in early 1997. In summary, DREA provides a sufficiently detailed and realistic ejector-mixer nozzle model at a computational cost compatible with preliminary design applications.

Versatile controllability of non-axisymmetric magnetic perturbations in KSTAR experiments

NASA Astrophysics Data System (ADS)

Han, Hyunsun; Jeon, Y. M.; in, Y.; Kim, J.; Yoon, S. W.; Hahn, S. H.; Ahn, H. S.; Woo, M. H.; Park, B. H.; Bak, J. G.; Kstar Team

2015-11-01

A newly upgraded IVCC (In-Vessel Control Coil) system equipped with four broadband power supplies, along with current connection patch panel, will be presented and discussed in terms of its capability on various KSTAR experiments. Until the last run-campaign, there were impressive experimental results on ELM(Edge Localized Mode) control experiments using the 3D magnetic field, but the non-axisymmetric field configuration could not be changed in a shot, let alone the limited number of accessible configurations. Introducing the new power supplies, such restrictions have been greatly reduced. Based on the preliminary commissioning results for 2015 KSTAR run-campaign, this new system has been confirmed to easily cope with various dynamic demands for toroidal and poloidal phases of 3D magnetic field in a shot. This enables us to diagnose the plasma response in more detail and to address the 3-D field impacts on the ELM behaviors better than ever.

Optimizing Decision Preparedness by Adapting Scenario Complexity and Automating Scenario Generation

NASA Technical Reports Server (NTRS)

Dunne, Rob; Schatz, Sae; Flore, Stephen M.; Nicholson, Denise

2011-01-01

Klein's recognition-primed decision (RPD) framework proposes that experts make decisions by recognizing similarities between current decision situations and previous decision experiences. Unfortunately, military personnel arQ often presented with situations that they have not experienced before. Scenario-based training (S8T) can help mitigate this gap. However, SBT remains a challenging and inefficient training approach. To address these limitations, the authors present an innovative formulation of scenario complexity that contributes to the larger research goal of developing an automated scenario generation system. This system will enable trainees to effectively advance through a variety of increasingly complex decision situations and experiences. By adapting scenario complexities and automating generation, trainees will be provided with a greater variety of appropriately calibrated training events, thus broadening their repositories of experience. Preliminary results from empirical testing (N=24) of the proof-of-concept formula are presented, and future avenues of scenario complexity research are also discussed.

A Comparison of Two Approaches to Safety Analysis Based on Use Cases

NASA Astrophysics Data System (ADS)

Stålhane, Tor; Sindre, Guttorm

Engineering has a long tradition in analyzing the safety of mechanical, electrical and electronic systems. Important methods like HazOp and FMEA have also been adopted by the software engineering community. The misuse case method, on the other hand, has been developed by the software community as an alternative to FMEA and preliminary HazOp for software development. To compare the two methods misuse case and FMEA we have run a small experiment involving 42 third year software engineering students. In the experiment, the students should identify and analyze failure modes from one of the use cases for a commercial electronic patient journals system. The results of the experiment show that on the average, the group that used misuse cases identified and analyzed more user related failure modes than the persons using FMEA. In addition, the persons who used the misuse cases scored better on perceived ease of use and intention to use.

How Much Can We Learn from a Single Chromatographic Experiment? A Bayesian Perspective.

PubMed

Wiczling, Paweł; Kaliszan, Roman

2016-01-05

In this work, we proposed and investigated a Bayesian inference procedure to find the desired chromatographic conditions based on known analyte properties (lipophilicity, pKa, and polar surface area) using one preliminary experiment. A previously developed nonlinear mixed effect model was used to specify the prior information about a new analyte with known physicochemical properties. Further, the prior (no preliminary data) and posterior predictive distribution (prior + one experiment) were determined sequentially to search towards the desired separation. The following isocratic high-performance reversed-phase liquid chromatographic conditions were sought: (1) retention time of a single analyte within the range of 4-6 min and (2) baseline separation of two analytes with retention times within the range of 4-10 min. The empirical posterior Bayesian distribution of parameters was estimated using the "slice sampling" Markov Chain Monte Carlo (MCMC) algorithm implemented in Matlab. The simulations with artificial analytes and experimental data of ketoprofen and papaverine were used to test the proposed methodology. The simulation experiment showed that for a single and two randomly selected analytes, there is 97% and 74% probability of obtaining a successful chromatogram using none or one preliminary experiment. The desired separation for ketoprofen and papaverine was established based on a single experiment. It was confirmed that the search for a desired separation rarely requires a large number of chromatographic analyses at least for a simple optimization problem. The proposed Bayesian-based optimization scheme is a powerful method of finding a desired chromatographic separation based on a small number of preliminary experiments.

SU-E-T-594: Preliminary Active Scanning Results of KHIMA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, C; Yang, T; Chang, S

Purpose: To verify the design criteria on heavy ion beam irradiation, developing a proto type active scanning system was purposed. The active scanning system consists of scanning magnet, power supplies, beam monitors, energy modulation system, and irradiation control system. Methods: Each components of the active scanning system was designed for carbon beam first. For the fast ramping a laminated yoke was purposed. To measure incoming dose and profile, a plate and strip type of ion chambers were designed. Also, ridge filter and range shifter was manufactured. And, the scanning system was modified to adopt 45 MeV of proton beam becausemore » of the absence of carbon ion beam in Korea. The system was installed in a beam line at MC-50, KIRAMS. Also, the irradiation control system and planning software was provided. Results: The scanning experiment was performed by drawing KHIMA logo on GaF film. The logo was scanned by 237 scanning points through time normalized intensity modulation. Also, a grid points scanning was performed to measure the scanning resolution and intensity resolution. Conclusion: A prototype active scanning system was successfully designed and manufactured. Also, an initial experiment to print out a drawing on GaF film through the scanning system was completed. More experiments would be required to specify the system performance.« less

Detection of early changes in lung-cell cytology by flow-systems analysis techniques. Progress report, January 1--June 30, 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinkamp, J. A.; Hansen, K. M.; Wilson, J. S.

1976-08-01

This report summarizes results of preliminary experiments to develop cytological and biochemical indicators for estimating damage to respiratory epithelium exposed to toxic agents associated with the by-products of nonnuclear energy production using advanced flow-systems cell-analysis technologies. Since initiation of the program one year ago, progress has been made in obtaining adequate numbers of exfoliated lung cells from the Syrian hamster for flow analysis; cytological techniques developed on human exfoliated gynecological samples have been adapted to hamster lung epithelium for obtaining single-cell suspensions; and lung-cell samples have been initially characterized based on DNA content, total protein, nuclear and cytoplasmic size, andmore » multiangle light-scatter measurements. Preliminary results from measurements of the above parameters which recently became available are described in this report. As the flow-systems technology is adapted further to analysis of exfoliated lung cells, measurements of changes in physical and biochemical cellular properties as a function of exposure to toxic agents will be performed.« less

Space vehicle integrated thermal protection/structural/meteoroid protection system, volume 1

NASA Technical Reports Server (NTRS)

Bartlett, D. H.; Zimmerman, D. K.

1973-01-01

A program was conducted to determine the merit of a combined structure/thermal meteoroid protection system for a cryogenic vehicle propulsion module. Structural concepts were evaluated to identify least weight designs. Thermal analyses determined optimum tank arrangements and insulation materials. Meteoroid penetration experiments provided data for design of protection systems. Preliminary designs were made and compared on the basis of payload capability. Thermal performance tests demonstrated heat transfer rates typical for the selected design. Meteoroid impact tests verified the protection characteristics. A mockup was made to demonstrate protection system installation. The best design found combined multilayer insulation with a truss structure vehicle body. The multilayer served as the thermal/meteoroid protection system.

The low energy muon beam profile monitor for the muon g-2/EDM experiment at J-PARC

NASA Astrophysics Data System (ADS)

Razuvaev, G. P.; Bae, S.; Choi, H.; Choi, S.; Ko, H. S.; Kim, B.; Kitamura, R.; Mibe, T.; Otani, M.

2017-09-01

The muon g-2/EDM experiment at J-PARC aims to measure the muon anomalous magnetic moment and electric dipole moment with high precision by utilising an ultracold muon beam. The current muon g-2 discrepancy between the Standard Model prediction and the experimental value is about 3.5 standard deviations. This experiment requires a development of the muon LINAC to accelerate thermal muons to the 300 MeV/c momentum. Detectors for beam diagnostics play a key role in such an experiment. The beam profile monitoring system has been designed to measure the profile of the low energy muon beam. It was tested during two beam tests in 2016 at the MLF D2 line at J-PARC. The detector was used with positive muons, Mu-(μ+ e- e-), p and H-, e- and UV light. The system overview and preliminary results are given. Special attention is paid to the spatial resolution of the beam profile monitor and online monitor software used during data taking.

Investigation of crew motion disturbances on Skylab-Experiment T-013. [for future manned spacecraft design

NASA Technical Reports Server (NTRS)

Conway, B. A.

1974-01-01

Astronaut crew motions can produce some of the largest disturbances acting on a manned spacecraft which can affect vehicle attitude and pointing. Skylab Experiment T-013 was developed to investigate the magnitude and effects of some of these disturbances on the Skylab spacecraft. The methods and techniques used to carry out this experiment are discussed, and preliminary results of data analysis presented. Initial findings indicate that forces on the order of 300 N were exerted during vigorous soaring activities, and that certain experiment activities produced spacecraft angular rate excursions 0.03 to 0.07 deg/sec. Results of Experiment T-013 will be incorporated into mathematical models of crew-motion disturbances, and are expected to be of significant aid in the sizing, design, and analysis of stabilization and control systems for future manned spacecraft.

Preliminary studies of electromagnetic sounding of cometary nuclei

NASA Technical Reports Server (NTRS)

Gabriel, A.; Warne, L.; Bednarczyk, S.; Elachi, C.

1978-01-01

The internal structure of a comet could be determined with a spacecraft borne electromagnetic sounder. A dielectric profile of the comet could be produced in direct analogy with terrestrial glacier and ice sheet sounding experiments. This profile would allow the detection of a rocky core or ice layers if they exist, just as layers in the ice and the bedrock interface have been clearly observed through the Greenland ice sheet. It would also provide a gross estimate of the amount of dust in the icy region. Models for the response of the nucleus and cometary plasma to electromagnetic sounding are developed and used to derive experimental parameters. A point system design was completed. Preliminary engineering study results indicate that the sounder is well within the bounds of current space technology.

The Large Area Crop Inventory Experiment /LACIE/ - An assessment after one year of operation

NASA Technical Reports Server (NTRS)

Macdonald, R. B.; Hall, F. G.; Erb, R. B.

1975-01-01

A Large Area Crop Inventory Experiment (LACIE) has been undertaken jointly by the U.S. Department of Agriculture (USDA), the National Oceanic and Atmospheric Administration (NOAA) of the Department of Commerce and the National Aeronautics and Space Administration (NASA) to prove out an economically important application of remote sensing from space. The first phase of the Experiment, which focused upon determinations of wheat area in the U.S. Great Plains and upon the development and testing of yield models, is now nearing completion. The system implemented to handle and analyze the Landsat and meteorological data has generally worked well and met operational goals. A very preliminary assessment of results to date indicates that the accuracy goals of the experiment can be met.

Design and preliminary accuracy studies of an MRI-guided transrectal prostate intervention system.

PubMed

Krieger, Axel; Csoma, Csaba; Iordachital, Iulian I; Guion, Peter; Singh, Anurag K; Fichtinger, Gabor; Whitcomb, Louis L

2007-01-01

This paper reports a novel system for magnetic resonance imaging (MRI) guided transrectal prostate interventions, such as needle biopsy, fiducial marker placement, and therapy delivery. The system utilizes a hybrid tracking method, comprised of passive fiducial tracking for initial registration and subsequent incremental motion measurement along the degrees of freedom using fiber-optical encoders and mechanical scales. Targeting accuracy of the system is evaluated in prostate phantom experiments. Achieved targeting accuracy and procedure times were found to compare favorably with existing systems using passive and active tracking methods. Moreover, the portable design of the system using only standard MRI image sequences and minimal custom scanner interfacing allows the system to be easily used on different MRI scanners.

Bio-Aerosol Detection Using Mass Spectrometry: Public Health Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ludvigson, Laura D.

2004-01-01

I recently spent a summer as an intern at the Lawrence Livermore National Laboratory. I worked on a project involving the real-time, reagentless, single cell detection of aerosolized pathogens using a novel mass spectrometry approach called Bio-Aerosol Mass Spectrometry (BAMS). Based upon preliminary results showing the differentiation capabilities of BAMS, I would like to explore the development and use of this novel detection system in the context of both environmental and clinical sample pathogen detection. I would also like to explore the broader public health applications that a system such as BAMS might have in terms of infectious disease preventionmore » and control. In order to appreciate the potential of this instrument, I will demonstrate the need for better pathogen detection methods, and outline the instrumentation, data analysis and preliminary results that lead me toward a desire to explore this technology further. I will also discuss potential experiments for the future along with possible problems that may be encountered along the way.« less

Preliminary Design Program: Vapor Compression Distillation Flight Experiment Program

NASA Technical Reports Server (NTRS)

Schubert, F. H.; Boyda, R. B.

1995-01-01

This document provides a description of the results of a program to prepare a preliminary design of a flight experiment to demonstrate the function of a Vapor Compression Distillation (VCD) Wastewater Processor (WWP) in microgravity. This report describes the test sequence to be performed and the hardware, control/monitor instrumentation and software designs prepared to perform the defined tests. the purpose of the flight experiment is to significantly reduce the technical and programmatic risks associated with implementing a VCD-based WWP on board the International Space Station Alpha.

Human Reliability Assessments: Using the Past (Shuttle) to Predict the Future (ORION)

NASA Technical Reports Server (NTRS)

Mott, Diana L.; Bigler, Mark A.

2017-01-01

NASA uses two HRA assessment methodologies. The first is a simplified method which is based on how much time is available to complete the action, with consideration included for environmental and personal factors that could influence the human's reliability. This method is expected to provide a conservative value or placeholder as a preliminary estimate. This preliminary estimate is used to determine which placeholder needs a more detailed assessment. The second methodology is used to develop a more detailed human reliability assessment on the performance of critical human actions. This assessment needs to consider more than the time available, this would include factors such as: the importance of the action, the context, environmental factors, potential human stresses, previous experience, training, physical design interfaces, available procedures/checklists and internal human stresses. The more detailed assessment is still expected to be more realistic than that based primarily on time available. When performing an HRA on a system or process that has an operational history, we have information specific to the task based on this history and experience. In the case of a PRA model that is based on a new design and has no operational history, providing a "reasonable" assessment of potential crew actions becomes more problematic. In order to determine what is expected of future operational parameters, the experience from individuals who had relevant experience and were familiar with the system and process previously implemented by NASA was used to provide the "best" available data. Personnel from Flight Operations, Flight Directors, Launch Test Directors, Control Room Console Operators and Astronauts were all interviewed to provide a comprehensive picture of previous NASA operations. Verification of the assumptions and expectations expressed in the assessments will be needed when the procedures, flight rules and operational requirements are developed and then finalized.

Preliminary pioneer 10 encounter results from the ames research center plasma analyzer experiment.

PubMed

Wolfe, J H; Collard, H R; Mihalov, J D; Intriligator, D S

1974-01-25

Preliminary results from the Ames Research Center plasma analyzer experiment for the Pioneer 10 Jupiter encounter indicate that Jupiter has a detached bow shock and magnetopause similar to the case at Earth but much larger in spatial extent. In contrast to Earth, Jupiter's outer magnetosphere appears to be highly inflated by thermal plasma and therefore highly responsive in size to changes in solar wind dynamic pressure.

W(h)ither the Sense of Wonder of Pre-Service Primary Teachers' when Teaching Science?: A Preliminary Study of Their Personal Experiences

ERIC Educational Resources Information Center

Stolberg, Tonie L.

2008-01-01

This preliminary study seeks to explore whether wonder-based reflections are sources of inspiration for our future teachers of science. What experiences have brought them personally a sense of wonder and when, if at all, do they employ scientific explanations of those events? In all 140 pre-service primary teachers, when questioned, described 240…

Apparatus analysis and preliminary design of low gravity porous solids experiment for STS Orbiter mid-deck

NASA Technical Reports Server (NTRS)

Fleeter, R. D.; Kropp, J. L.

1983-01-01

The apparatus analysis laboratory equipment design and fabrication and the preliminary design of the Combustion of Porous Solids Experiment for operation in the mid-deck area of the Shuttle are described. The apparatus analysis indicated that the mid-deck region of the STS was a feasible region of the Shuttle for operation. A sixteen tube concept was developed with tubes of 75 cm length and up to 5.6 cm accommodated. The experiment is viewed by IR sensors and a 16 mm camera. Laboratory equipment was designed and fabricated to test the parible injection, mixing and venting concepts. This equipment was delivered to NASA/LeRC. A preliminary design was made for the experiment based upon the apparatus analysis. The design incorporated results from the Phase ""O'' Safety Review. This design utilizes a closed tube concept in which the particles are stored, injected and burned with no coupling to the Shuttle environment. Drawings of the major components and an assembly are given. The electronics are described for the experiment. An equipment list is presented and an experiment weight estimate is determined. The mission operation requirements are outlined.

Rainfall assimilation in RAMS by means of the Kuo parameterisation inversion: method and preliminary results

NASA Astrophysics Data System (ADS)

Orlandi, A.; Ortolani, A.; Meneguzzo, F.; Levizzani, V.; Torricella, F.; Turk, F. J.

2004-03-01

In order to improve high-resolution forecasts, a specific method for assimilating rainfall rates into the Regional Atmospheric Modelling System model has been developed. It is based on the inversion of the Kuo convective parameterisation scheme. A nudging technique is applied to 'gently' increase with time the weight of the estimated precipitation in the assimilation process. A rough but manageable technique is explained to estimate the partition of convective precipitation from stratiform one, without requiring any ancillary measurement. The method is general purpose, but it is tuned for geostationary satellite rainfall estimation assimilation. Preliminary results are presented and discussed, both through totally simulated experiments and through experiments assimilating real satellite-based precipitation observations. For every case study, Rainfall data are computed with a rapid update satellite precipitation estimation algorithm based on IR and MW satellite observations. This research was carried out in the framework of the EURAINSAT project (an EC research project co-funded by the Energy, Environment and Sustainable Development Programme within the topic 'Development of generic Earth observation technologies', Contract number EVG1-2000-00030).

Analysis of the Radiated Field in an Electromagnetic Reverberation Chamber as an Upset-Inducing Stimulus for Digital Systems

NASA Technical Reports Server (NTRS)

Torres-Pomales, Wilfredo

2012-01-01

Preliminary data analysis for a physical fault injection experiment of a digital system exposed to High Intensity Radiated Fields (HIRF) in an electromagnetic reverberation chamber suggests a direct causal relation between the time profile of the field strength amplitude in the chamber and the severity of observed effects at the outputs of the radiated system. This report presents an analysis of the field strength modulation induced by the movement of the field stirrers in the reverberation chamber. The analysis is framed as a characterization of the discrete features of the field strength waveform responsible for the faults experienced by a radiated digital system. The results presented here will serve as a basis to refine the approach for a detailed analysis of HIRF-induced upsets observed during the radiation experiment. This work offers a novel perspective into the use of an electromagnetic reverberation chamber to generate upset-inducing stimuli for the study of fault effects in digital systems.

ATTDES: An Expert System for Satellite Attitude Determination and Control. 2

NASA Technical Reports Server (NTRS)

Mackison, Donald L.; Gifford, Kevin

1996-01-01

The design, analysis, and flight operations of satellite attitude determintion and attitude control systems require extensive mathematical formulations, optimization studies, and computer simulation. This is best done by an analyst with extensive education and experience. The development of programs such as ATTDES permit the use of advanced techniques by those with less experience. Typical tasks include the mission analysis to select stabilization and damping schemes, attitude determination sensors and algorithms, and control system designs to meet program requirements. ATTDES is a system that includes all of these activities, including high fidelity orbit environment models that can be used for preliminary analysis, parameter selection, stabilization schemes, the development of estimators covariance analyses, and optimization, and can support ongoing orbit activities. The modification of existing simulations to model new configurations for these purposes can be an expensive, time consuming activity that becomes a pacing item in the development and operation of such new systems. The use of an integrated tool such as ATTDES significantly reduces the effort and time required for these tasks.

Effect of descriptive information and experience on automation reliance.

PubMed

Yuviler-Gavish, Nirit; Gopher, Daniel

2011-06-01

The present research addresses the issue of reliance on decision support systems for the long-term (DSSLT), which help users develop decision-making strategies and long-term planning. It is argued that providing information about a system's future performance in an experiential manner, as compared with a descriptive manner, encourages users to increase their reliance level. Establishing appropriate reliance on DSSLT is contingent on the system developer's ability to provide users with information about the system's future performance. A sequence of three studies contrasts the effect on automation reliance of providing descriptive information versus experience for DSSLT with two different positive expected values of recommendations. Study I demonstrated that when automation reliance was determined solely on the basis of description, it was relatively low, but it increased significantly when a decision was made after experience with 50 training simulations. Participants were able to learn to increase their automation reliance levels when they encountered the same type of recommendation again. Study 2 showed that the absence of preliminary descriptive information did not affect the automation reliance levels obtained after experience. Study 3 demonstrated that participants were able to generalize their learning about increasing reliance levels to new recommendations. Using experience rather than description to give users information about future performance in DSSLT can help increase automation reliance levels. Implications for designing DSSLT and decision support systems in general are discussed.

Microgravity Acceleration Environment of the International Space Station (panel)

NASA Technical Reports Server (NTRS)

DeLombard, Richard; Hrovat, Kenneth; Kelly, Eric; McPherson, Kevin; Foster, William M.; Schafer, Craig P.

2001-01-01

This paper examines the microgravity environment provided to the early science experiments by the International Space Station vehicle which is under construction. The microgravity environment will be compared with predicted levels for this stage of assembly. Included are initial analyses of the environment and preliminary identification of some sources of accelerations. Features of the operations of the accelerometer instruments, the data processing system, and data dissemination to users are also described.

Pre-X Experimental Re-Entry Lifting Body: Design of Flight Test Experiments for Critical Aerothermal Phenomena

DTIC Science & Technology

2007-06-01

the CNES proposal to perform in-flight experimentation mainly on reusable thermal protections, aero-thermo-dynamics and guidance to secure the second...the vehicle. A preliminary in-flight experimentation and measurement plan has been assessed defining the main objectives in terms of reusable Thermal ...Energy Management THEFA Thermographie Face Arrière TPS Thermal Protection System VKI Von Karman Institute WRT With Respect To WTT Wind

Automated Support for da Vinci Surgical System

DTIC Science & Technology

2011-05-01

MScore, which provides objective assessment measuring robotic surgery skills across all computed metrics (Figure 7). In addition to viewing single ...holding an object. Data Collection & Analysis (Task 5)  Preliminary Experiments  During the first phase of data collection, a single performance of...a single task (anastomosis) trial was recorded from six different users – three each for the da Vinci and the dV-Trainer platforms. On each platform

Hollow Core Optical Fiber Gas Lasers: Toward Novel and Practical Systems in Fused Silica

DTIC Science & Technology

2017-05-18

Hollow core Optically pumped Fiber Gas LASer’s (HOFGLAS’s) based on population inversion combine advantages of fiber lasers such as long interaction...polarization dependent fiber properties. Preliminary experiments were performed toward simultaneous lasing in the visible and near infrared; lasing in...words) Hollow core Optically pumped Fiber Gas LASer’s (HOFGLAS’s) based on population inversion combine advantages of fiber lasers such as long

Development of stable low-electroosmotic mobility coatings. [for use in electrophoresis systems in space

NASA Technical Reports Server (NTRS)

Vanderhoff, J. W.; Micale, F. J.

1979-01-01

Long-time rinsings of the Z6040-methlycellulose coating used successfully on the ASTP MA=011 experiment indicate the permanency of this coating is inadequate for continuous flowing systems. Two approaches are described for developing coatings which are stable under continuous fluid movement and which exhibit finite and predictable electroosmotic mobility values while being effective on different types of surfaces, such as glass, plastics, and ceramic alumina, such as is currently used as the electrophoresis channel in the GE-SPAR-CPE apparatus. The surface charge modification of polystyrene latex, especially by protein absorption, to be used as model materials for ground-based electrophoresis experiments, and the preliminary work directed towards the seeded polymerization of large-particle-size monodisperse latexes in a microgravity environment are discussed.

Intelligent personal health record: experience and open issues.

PubMed

Luo, Gang; Tang, Chunqiang; Thomas, Selena B

2012-08-01

Web-based personal health records (PHRs) are under massive deployment. To improve PHR's capability and usability, we previously proposed the concept of intelligent PHR (iPHR). By introducing and extending expert system technology and Web search technology into the PHR domain, iPHR can automatically provide users with personalized healthcare information to facilitate their daily activities of living. Our iPHR system currently provides three functions: guided search for disease information, recommendation of home nursing activities, and recommendation of home medical products. This paper discusses our experience with iPHR as well as the open issues, including both enhancements to the existing functions and potential new functions. We outline some preliminary solutions, whereas a main purpose of this paper is to stimulate future research work in the area of consumer health informatics.

Heat flow control and segregation in directional solidification: Development of an experimental and theoretical basis for Bridgman-type growth experiments in a microgravity environment

NASA Technical Reports Server (NTRS)

Witt, A. F.

1986-01-01

Within the framework of the proposed research, emphasis was placed on application of magnetic fields to semiconductor growth systems. It was found that magnetic fields up to 3 kGauss do not affect the growth behavior nor the macro-segregation behavior in the system Ge(Ga). Applied fields are found to significantlty alter the radial dopant distribution, which is attributed to alterations in the spatial orientation of convective cells. Increasing the magnetic field to 30 kGauss is found to have a fundamental effect on dopant segregation. Emphasis is also placed on the potential of KC-135 flights for preliminary studies on the effects of reduced gravity environments on the wetting behavior of semiconductor systems in growth configuration. The limited number of experiments conducted does not allow any conclusions on the merits of KC-135 flights for semiconductor processing research.

A combustion driven shock tunnel to complement the free piston shock tunnel T5 at GALCIT

NASA Technical Reports Server (NTRS)

Belanger, Jacques; Hornung, Hans G.

1992-01-01

A combustion driven shock tunnel was designed and built at GALCIT to supply the hypersonic facility T5 with 'hot' hydrogen for mixing and combustion experiments. This system was chosen over other options for better flexibility and for safety reasons. The shock tunnel is described and the overall efficiency of the system is discussed. The biggest challenge in the design was to synchronize the combustion driven shock tunnel with T5. To do so, the main diaphragm of the combustion driven shock tunnel is locally melted by an electrical discharge. This local melting is rapidly followed by the complete collapse of the diaphragm in a very repeatable way. A first set of experiments on supersonic hydrogen transverse jets over a flat plate have just been completed with the system and some of the preliminary results are presented.

A Hybrid Positioning Strategy for Vehicles in a Tunnel Based on RFID and In-Vehicle Sensors

PubMed Central

Song, Xiang; Li, Xu; Tang, Wencheng; Zhang, Weigong; Li, Bin

2014-01-01

Many intelligent transportation system applications require accurate, reliable, and continuous vehicle positioning. How to achieve such positioning performance in extended GPS-denied environments such as tunnels is the main challenge for land vehicles. This paper proposes a hybrid multi-sensor fusion strategy for vehicle positioning in tunnels. First, the preliminary positioning algorithm is developed. The Radio Frequency Identification (RFID) technology is introduced to achieve preliminary positioning in the tunnel. The received signal strength (RSS) is used as an indicator to calculate the distances between the RFID tags and reader, and then a Least Mean Square (LMS) federated filter is designed to provide the preliminary position information for subsequent global fusion. Further, to improve the positioning performance in the tunnel, an interactive multiple model (IMM)-based global fusion algorithm is developed to fuse the data from preliminary positioning results and low-cost in-vehicle sensors, such as electronic compasses and wheel speed sensors. In the actual implementation of IMM, the strong tracking extended Kalman filter (STEKF) algorithm is designed to replace the conventional extended Kalman filter (EKF) to achieve model individual filtering. Finally, the proposed strategy is evaluated through experiments. The results validate the feasibility and effectiveness of the proposed strategy. PMID:25490581

A hybrid positioning strategy for vehicles in a tunnel based on RFID and in-vehicle sensors.

PubMed

Song, Xiang; Li, Xu; Tang, Wencheng; Zhang, Weigong; Li, Bin

2014-12-05

Many intelligent transportation system applications require accurate, reliable, and continuous vehicle positioning. How to achieve such positioning performance in extended GPS-denied environments such as tunnels is the main challenge for land vehicles. This paper proposes a hybrid multi-sensor fusion strategy for vehicle positioning in tunnels. First, the preliminary positioning algorithm is developed. The Radio Frequency Identification (RFID) technology is introduced to achieve preliminary positioning in the tunnel. The received signal strength (RSS) is used as an indicator to calculate the distances between the RFID tags and reader, and then a Least Mean Square (LMS) federated filter is designed to provide the preliminary position information for subsequent global fusion. Further, to improve the positioning performance in the tunnel, an interactive multiple model (IMM)-based global fusion algorithm is developed to fuse the data from preliminary positioning results and low-cost in-vehicle sensors, such as electronic compasses and wheel speed sensors. In the actual implementation of IMM, the strong tracking extended Kalman filter (STEKF) algorithm is designed to replace the conventional extended Kalman filter (EKF) to achieve model individual filtering. Finally, the proposed strategy is evaluated through experiments. The results validate the feasibility and effectiveness of the proposed strategy.

Preliminary analysis of WL experiment number 701: Space environment effects on operating fiber optic systems

NASA Technical Reports Server (NTRS)

Taylor, E. W.; Padden, R. J.; Berry, J. N.; Sanchez, A. D.; Chapman, S. P.

1991-01-01

A brief overview of the analysis performed on WL Experiment number 701 is presented, highlighting the successful operation of the first know active fiber optic links orbited in space. Four operating fiber optic links were exposed to the space environment for a period exceeding five years, situated aboard and external to the Long Duration Exposure Facility (LDEF). Despite the prolonged space exposure to radiation, wide temperature extremums, atomic oxygen interactions, and micrometeorite and debris impacts, the optical data links performed well within specification limits. Early Phillips Laboratory tests and analyses performed on the experiment and its recovered magnetic tape data strongly indicate that fiber optic application in space will have a high success rate.

High Resolution Λ Hypernuclear Spectroscopy with Electron Beams

NASA Astrophysics Data System (ADS)

Gogami, T.; Achenbach, P.; Ahmidouch, A.; Albayrak, I.; Androic, D.; Asaturyan, A.; Asaturyan, R.; Ates, O.; Baturin, P.; Badui, R.; Boeglin, W.; Bono, J.; Brash, E.; Carter, P.; Chen, C.; Chiba, A.; Christy, E.; Danagoulian, S.; De Leo, R.; Doi, D.; Elaasar, M.; Ent, R.; Fujii, Y.; Fujita, M.; Furic, M.; Gabrielyan, M.; Gan, L.; Garibaldi, F.; Gaskell, D.; Gasparian, A.; Hashimoto, O.; Horn, T.; Hu, B.; Hungerford, Ed. V.; Jones, M.; Kanda, H.; Kaneta, M.; Kato, S.; Kawai, M.; Kawama, D.; Khanal, H.; Kohl, M.; Liyanage, A.; Luo, W.; Maeda, K.; Margaryan, A.; Markowitz, P.; Maruta, T.; Matsumura, A.; Maxwell, V.; Mkrtchyan, A.; Mkrtchyan, H.; Nagao, S.; Nakamura, S. N.; Narayan, A.; Neville, C.; Niculescu, G.; Niculescu, M. I.; Nunez, A.; Nuruzzaman; Okayasu, Y.; Petkovic, T.; Pochodzalla, J.; Qiu, X.; Reinhold, J.; Rodriguez, V. M.; Samanta, C.; Sawatzky, B.; Seva, T.; Shichijo, A.; Tadevosyan, V.; Tang, L.; Taniya, N.; Tsukada, K.; Veilleux, M.; Vulcan, W.; Wesselmann, F. R.; Wood, S. A.; Yamamoto, T.; Ya, L.; Ye, Z.; Yokota, K.; Yuan, L.; Zhamkochyan, S.; Zhu, L.

JLab E05-115 which is an experiment for Λ hypernuclear spectroscopy with electron beams was carried out at Jefferson Lab (JLab) in 2009. In the experiment, Λ 7He, Λ 9Li, Λ 10Be, Λ 12B and Λ 52V were measured by new magnetic spectrometer systems (SPL+HES+HKS) which were necessary for spectroscopy with high energy resolution of sub-MeV (FWHM). This is the first attempt to measure a Λ hypernucleus with up to medium-heavy mass region by the (e,e' K + ) reaction, overcoming high rate and high multiplicity conditions due to electromagnetic background particles. An overview of the hypernuclear experiments at JLab Hall-C and preliminary binding energy spectrum of Λ 10Be are shown.

High frame-rate en face optical coherence tomography system using KTN optical beam deflector

NASA Astrophysics Data System (ADS)

Ohmi, Masato; Shinya, Yusuke; Imai, Tadayuki; Toyoda, Seiji; Kobayashi, Junya; Sakamoto, Tadashi

2017-02-01

We developed high frame-rate en face optical coherence tomography (OCT) system using KTa1-xNbxO3 (KTN) optical beam deflector. In the imaging system, the fast scanning was performed at 200 kHz by the KTN optical beam deflector, while the slow scanning was performed at 800 Hz by the galvanometer mirror. As a preliminary experiment, we succeeded in obtaining en face OCT images of human fingerprint with a frame rate of 800 fps. This is the highest frame-rate obtained using time-domain (TD) en face OCT imaging. The 3D-OCT image of sweat gland was also obtained by our imaging system.

Development of a severe local storm prediction system: A 60-day test of a mesoscale primitive equation model

NASA Technical Reports Server (NTRS)

Paine, D. A.; Zack, J. W.; Kaplan, M. L.

1979-01-01

The progress and problems associated with the dynamical forecast system which was developed to predict severe storms are examined. The meteorological problem of severe convective storm forecasting is reviewed. The cascade hypothesis which forms the theoretical core of the nested grid dynamical numerical modelling system is described. The dynamical and numerical structure of the model used during the 1978 test period is presented and a preliminary description of a proposed multigrid system for future experiments and tests is provided. Six cases from the spring of 1978 are discussed to illustrate the model's performance and its problems. Potential solutions to the problems are examined.

Development of novel high-speed en face optical coherence tomography system using KTN optical beam deflector

NASA Astrophysics Data System (ADS)

Ohmi, Masato; Fukuda, Akihiro; Miyazu, Jun; Ueno, Masahiro; Toyoda, Seiji; Kobayashi, Junya

2015-02-01

We developed a novel high-speed en face optical coherence tomography (OCT) system using a KTa1-xNbxO3 (KTN) optical beam deflector. Using the imaging system, fast scanning was performed at 200 kHz by the KTN beam deflector, while slow scanning was performed at 400 Hz by the galvanometer mirror. In a preliminary experiment, we obtained en face OCT images of a human fingerprint at 400 fps. This is the highest speed reported in time-domain en face OCT imaging and is comparable to the speed of swept-source OCT. A 3D-OCT image of a sweat gland was also obtained by our imaging system.

Hierarchical modeling and robust synthesis for the preliminary design of large scale complex systems

NASA Astrophysics Data System (ADS)

Koch, Patrick Nathan

Large-scale complex systems are characterized by multiple interacting subsystems and the analysis of multiple disciplines. The design and development of such systems inevitably requires the resolution of multiple conflicting objectives. The size of complex systems, however, prohibits the development of comprehensive system models, and thus these systems must be partitioned into their constituent parts. Because simultaneous solution of individual subsystem models is often not manageable iteration is inevitable and often excessive. In this dissertation these issues are addressed through the development of a method for hierarchical robust preliminary design exploration to facilitate concurrent system and subsystem design exploration, for the concurrent generation of robust system and subsystem specifications for the preliminary design of multi-level, multi-objective, large-scale complex systems. This method is developed through the integration and expansion of current design techniques: (1) Hierarchical partitioning and modeling techniques for partitioning large-scale complex systems into more tractable parts, and allowing integration of subproblems for system synthesis, (2) Statistical experimentation and approximation techniques for increasing both the efficiency and the comprehensiveness of preliminary design exploration, and (3) Noise modeling techniques for implementing robust preliminary design when approximate models are employed. The method developed and associated approaches are illustrated through their application to the preliminary design of a commercial turbofan turbine propulsion system; the turbofan system-level problem is partitioned into engine cycle and configuration design and a compressor module is integrated for more detailed subsystem-level design exploration, improving system evaluation.

Towards sub-100 fs multi-GW pulses directly emitted from a Thulium-doped fiber CPA system

NASA Astrophysics Data System (ADS)

Gaida, C.; Gebhardt, M.; Stutzki, F.; Jauregui, C.; Limpert, J.; Tünnermann, A.

2017-02-01

Experimental demonstrations of Tm-doped fiber amplifiers (typically in CW- or narrow-band pulsed operation) span a wavelength range going from about 1700 nm to well beyond 2000 nm. Thus, it should be possible to obtain a bandwidth of more than 100 nm, which would enable sub-100 fs pulse duration in an efficient, linear amplification scheme. In fact, this would allow the emission of pulses with less than 20 optical cycles directly from a Tm-doped fiber system, something that seems to be extremely challenging for other dopants in a fused silica fiber. In this contribution, we summarize the current development of our Thulium-doped fiber CPA system, demonstrate preliminary experiments for further scaling and discuss important design factors for the next steps. The current single-channel laser system presented herein delivers a pulse-peak power of 2 GW and a nearly transform-limited pulse duration of 200 fs in combination with 28.7 W of average power. Special care has been taken to reduce the detrimental impact of water vapor absorption by placing the whole system in a dry atmosphere housing (<0.1% rel. humidity) and by using a sufficiently long wavelength (1920-1980 nm). The utilization of a low-pressure chamber in the future will allow for the extension of the amplification bandwidth. Preliminary experiments demonstrating a broader amplification bandwidth that supports almost 100 fs pulse duration and average power scaling to < 100W have already been performed. Based on these results, a Tm-doped fiber CPA with sub-100 fs pulse duration, multi-GW pulse peak power and >100 W average power can be expected in the near future.

Methodology on Investigating the Influences of Automated Material Handling System in Automotive Assembly Process

NASA Astrophysics Data System (ADS)

Saffar, Seha; Azni Jafar, Fairul; Jamaludin, Zamberi

2016-02-01

A case study was selected as a method to collect data in actual industry situation. The study aimed to assess the influences of automated material handling system in automotive industry by proposing a new design of integration system through simulation, and analyze the significant effect and influence of the system. The method approach tool will be CAD Software (Delmia & Quest). The process of preliminary data gathering in phase 1 will collect all data related from actual industry situation. It is expected to produce a guideline and limitation in designing a new integration system later. In phase 2, an idea or concept of design will be done by using 10 principles of design consideration for manufacturing. A full factorial design will be used as design of experiment in order to analyze the performance measured of the integration system with the current system in case study. From the result of the experiment, an ANOVA analysis will be done to study the performance measured. Thus, it is expected that influences can be seen from the improvement made in the system.

Shallow Water Acoustic Experiments and Preliminary Planning for FY06 Fieldwork

DTIC Science & Technology

2011-03-21

To) 5/1/2005-12/31/2010 4. TITLE AND SUBTITLE Shallow Water Acoustic Experiments and Preliminary Planning for FY06 Fieldwork 5a. CONTRACT NUMBERS...numerical computations show horizontal interference patterns within the duct. Richly de - tailed sound radiation fields are predicted at locations far...4) for the vertical modal amplitude Tm at x^L is now de - scribed in detail. First, the assumption of total transmission at the open-ended

Preliminary Findings from the SHERE ISS Experiment

NASA Technical Reports Server (NTRS)

Hall, Nancy R.; McKinley, Gareth H.; Erni, Philipp; Soulages, Johannes; Magee, Kevin S.

2009-01-01

The Shear History Extensional Rheology Experiment (SHERE) is an International Space Station (ISS) glovebox experiment designed to study the effect of preshear on the transient evolution of the microstructure and viscoelastic tensile stresses for monodisperse dilute polymer solutions. The SHERE experiment hardware was launched on Shuttle Mission STS-120 (ISS Flight 10A) on October 22, 2007, and 20 fluid samples were launched on Shuttle Mission STS-123 (ISS Flight 10/A) on March 11, 2008. Astronaut Gregory Chamitoff performed experiments during Increment 17 on the ISS between June and September 2008. A summary of the ten year history of the hardware development, the experiment's science objectives, and Increment 17's flight operations are discussed in the paper. A brief summary of the preliminary science results is also discussed.

Evaluation Of The Diagnostic Performance Of A Multimedia Medical Communications System.

NASA Astrophysics Data System (ADS)

Robertson, John G.; Coristine, Marjorie; Goldberg, Morris; Beeton, Carolyn; Belanger, Garry; Tombaugh, Jo W.; Hickey, Nancy M.; Millward, Steven F.; Davis, Michael; Whittingham, David

1989-05-01

The central concern of radiologists when evaluating Picture Archiving Communication System (PACS) is the diagnostic performance of digital images compared to the original analog versions of the same images. Considerable work has been done comparing the ROC curves of various types of digital systems to the corresponding analog systems for the detection of specific phantoms or diseases. Although the studies may notify the radiologists that for a specific lesion a digital system may perform as well as the analog system, it tells the radiologists very little about the impact on diagnostic performance of a digital system in the general practice of radiology. We describe in this paper an alternative method for evaluating the diagnostic performance of a digital system and a preliminary experiment we conducted to test the methodology.

The potential role of aerobic biological waste treatment in regenerative life support systems

NASA Technical Reports Server (NTRS)

Shuler, M. L.; Nafis, D.; Sze, E.

1981-01-01

The purpose of the paper is to make a preliminary assessment of the feasibility of using aerobic biological waste treatment in closed systems. Issues that are addressed in this paper are: (1) how high a degree of material balance is possible, (2) how much might such a system weigh, and (3) how would system closure and weight be affected if animals were included in the system. A computer model has been developed to calculate for different scenarios the compositions and amounts of the streams entering or leaving the waste treatment system and to estimate the launch weight of such a system. A bench scale apparatus has been built to mimic the proposed waste treatment system; the experiments are used to verify model predictions and to improve model parameter estimations.

Preliminary scientific rationale for a voyage to a thousand astronomical units

NASA Technical Reports Server (NTRS)

Etchegaray, M. I. (Compiler)

1987-01-01

A proposed mission to 1000 astronomical units (TAU) is under study by the Jet Propulsion Laboratory. Launch date for a TAU mission is likely to be well into the first decade of the 21st century. Study of TAU has focused on the technologies required to carry out this ambitious mission and the identification of preliminary scientific rationale for such a deep space flight. A 1-MW nuclear-powered electric propulsion (NEP) system forms the baseline method for achieving the high velocities required. A solar system escape velocity of 106 km/s is needed to propel the TAU vehicle to 1000 AU in 50 years. The NEP system must accelerate the vehicle for about ten years before this velocity is attained because of the extremely low thrust nature of the xenon-fueled ion engines. At the end of the thrusting phase the NEP system is jettisoned to allow the TAU spacecraft and science experiments to coast out to 1000 AU. Another important technology for TAU is advanced optical communication systems, which are envisioned for transmitting science data to Earth. A 1-m optical telescope combined with a 10-W laser transponder can transmit 20 kbps to a 10-m Earth-orbit-based telescope from 1000 AU.

Preliminary Research on Possibilities of Drilling Process Robotization

NASA Astrophysics Data System (ADS)

Pawel, Stefaniak; Jacek, Wodecki; Jakubiak, Janusz; Zimroz, Radoslaw

2017-12-01

Nowadays, drilling & blasting is crucial technique for deposit excavation using in hard rock mining. Unfortunately, such approach requires qualified staff to perform, and consequently there is a serious risk related to rock mechanics when using explosives. Negative influence of explosives usage on safety issues of underground mine is a main cause of mining demands related to elimination of people from production area. Other aspects worth taking into consideration are drilling precision according to drilling pattern, blasting effectiveness, improvement of drilling tool reliability etc. In the literature different drilling support solutions are well-known in terms of positioning support systems, anti-jamming systems or cavity detection systems. For many years, teleoperation of drilling process is also developed. Unfortunately, available technologies have so far not fully met the industries expectation in hard rock. Mine of the future is expected to incorporate robotic system instead of current approaches. In this paper we present preliminary research related to robotization of drilling process and possibilities of its application in underground mine condition. A test rig has been proposed. To simulate drilling process several key assumptions have been accepted. As a result, algorithms for automation of drilling process have been proposed and tested on the test rig. Experiences gathered so far underline that there is a need for further developing robotic system for drilling process.

Advanced piloted aircraft flight control system design methodology. Volume 1: Knowledge base

NASA Technical Reports Server (NTRS)

Mcruer, Duane T.; Myers, Thomas T.

1988-01-01

The development of a comprehensive and electric methodology for conceptual and preliminary design of flight control systems is presented and illustrated. The methodology is focused on the design stages starting with the layout of system requirements and ending when some viable competing system architectures (feedback control structures) are defined. The approach is centered on the human pilot and the aircraft as both the sources of, and the keys to the solution of, many flight control problems. The methodology relies heavily on computational procedures which are highly interactive with the design engineer. To maximize effectiveness, these techniques, as selected and modified to be used together in the methodology, form a cadre of computational tools specifically tailored for integrated flight control system preliminary design purposes. While theory and associated computational means are an important aspect of the design methodology, the lore, knowledge and experience elements, which guide and govern applications are critical features. This material is presented as summary tables, outlines, recipes, empirical data, lists, etc., which encapsulate a great deal of expert knowledge. Much of this is presented in topical knowledge summaries which are attached as Supplements. The composite of the supplements and the main body elements constitutes a first cut at a a Mark 1 Knowledge Base for manned-aircraft flight control.

Preliminary results from the Arecibo Heating Experiment (HEX): HF to GNSS

NASA Astrophysics Data System (ADS)

Jackson-Booth, N.; Penney, R.; Bernhardt, P. A.; Martin, P. L.; Buckland, R.; Morton-Orr, T.; Nossa, E.; Buckland, R.

2017-12-01

The ionosphere is subject to many solar and terrestrial influences that can generate disturbances, causing degradation to modern communication and navigational systems. Whilst the disturbances are normally caused by natural phenomena such as hurricanes, earthquakes and solar storms; they can also be generated by artificially modifying the ionosphere. Artificial Ionospheric Modification (AIM) attempts to alter a small region of the ionosphere in order to perturb the RF propagation environment. This can be achieved through injecting the ionosphere with aerosols, chemicals or radio signals. The effects of any such modification can be detected through the deployment of sensors, including ground based high-frequency (HF) sounders and dual-band Global Navigation Satellite System (GNSS) receivers. HF sounders allow measurements of the bottom-side of the ionosphere. GNSS receivers offer a convenient means of obtaining information about the ionosphere, including ionospheric disturbances through changes in the derived total electron content information. The Heating EXperiment (HEX), which took place in March and May 2017, was designed to further our understanding of the phenomena caused by artificially heating a small region of the ionosphere, using the Arecibo facility in Puerto Rico. This was achieved by utilizing a HF measurement experiment spread between Texas and Trinidad and the deployment of a small scale travelling ionospheric disturbance (TID) network near the heater. The TID network comprised three GNSS receivers along baselines of approximately 4 km, located 20 km north of the heater. This paper presents preliminary results from the HEX campaign, including evidence of heating-induced disturbances enhancing propagation between Virginia and Trinidad. The implications of generated irregularities on GNSS will also be discussed.

Overview of the Preliminary Design of the Optical Communication Demonstration and High-Rate Link Facility

NASA Technical Reports Server (NTRS)

Sandusky, John V.; Jeganathan, M.; Ortiz, G.; Biswas, A.; Lee, S.; Parker, G.; Liu, B.; Johnson, D.; DePew, J.; Lesh, J. R.

2000-01-01

Tlis paper presents an overview of the preliminary design of both the flight and ground systems of the Optical Communication Demonstration and High-Rate Link Facility which will demonstrate optical communication from the International Space Station to ground after its deployment in October 2002. The overview of the preliminary design of the Flight System proceeds by contrasting it with the design of the laboratory-model unit, emphasizing key changes and the rationale behind the design choices. After presenting the preliminary design of the Ground System, the timetable for the construction and deployment of the flight and ground systems is outlined.

Fiscal year 1981 US corn and soybeans pilot preliminary experiment plan, phase 1

NASA Technical Reports Server (NTRS)

Livingston, G. P.; Nedelman, K. S.; Norwood, D. F.; Smith, J. H. (Principal Investigator)

1981-01-01

A draft of the preliminary experiment plan for the foreign commodity production forecasting project fiscal year 1981 is presented. This draft plan includes: definition of the phase 1 and 2 U.S. pilot objectives; the proposed experiment design to evaluate crop calendar, area estimation, and area aggregation components for corn and soybean technologies using 1978/1979 crop-year data; a description of individual sensitivity evaluations of the baseline corn and soybean segment classification procedure; and technology and data assessment in support of the corn and soybean estimation technology for use in the U.S. central corn belt.

Infrared Camera Diagnostic for Heat Flux Measurements on NSTX

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. Mastrovito; R. Maingi; H.W. Kugel

2003-03-25

An infrared imaging system has been installed on NSTX (National Spherical Torus Experiment) at the Princeton Plasma Physics Laboratory to measure the surface temperatures on the lower divertor and center stack. The imaging system is based on an Indigo Alpha 160 x 128 microbolometer camera with 12 bits/pixel operating in the 7-13 {micro}m range with a 30 Hz frame rate and a dynamic temperature range of 0-700 degrees C. From these data and knowledge of graphite thermal properties, the heat flux is derived with a classic one-dimensional conduction model. Preliminary results of heat flux scaling are reported.

Mechanism of Electromagnetic Energy Effects of the Nervous System. Experimental System and Preliminary Results.

DTIC Science & Technology

1982-07-01

17 * 7 Expulsion of pipette by cell... 17 8 Effects of curare on cell studied 27 June 1980 ... 18 9 Pipette experiment, 18 July 1980 ... 27 10...Response of cell studied 18 August 1980 to sudden dc shift... 29 3 3 FIGURES (cont’d) C-Ia-c Baseline period of cell studied 18 June 1980 ... page 49 C-2a-c...Exposure period of cell studied 18 June 1980 ... 50 C-3a-c Post-exposure period of cell studied 18 June 1980 ... 51 C-4a-d Baseline, first exposure

Physician/Computer Interaction

PubMed Central

Dlugacz, Yosef D.; Siegel, Carole; Fischer, Susan

1981-01-01

Despite the fact that the physician's involvement with computer operations has dramatically increased with automation in the health care industry, few studies have focused on the physician's experiences with and reactions to computers. This paper reports on these dimensions for physicians and their medical supervisors who have begun to use a computerized drug review system. Their attitudes and opinions are assessed towards this system and more generally towards the use of computers in medicine. Clinicians' attitudes towards computers are related to their clinical role and feelings about the working milieu. This report presents preliminary data of the study in terms of the frequency distribution of responses.

Magnetohydrodynamic Augmented Propulsion Experiment

NASA Technical Reports Server (NTRS)

Litchford, Ron J.

2008-01-01

Over the past several years, efforts have been under way to design and develop an operationally flexible research facility for investigating the use of cross-field MHD accelerators as a potential thrust augmentation device for thermal propulsion systems. The baseline configuration for this high-power experimental facility utilizes a 1.5-MWe multi-gas arc-heater as a thermal driver for a 2-MWe MHD accelerator, which resides in a large-bore 2-tesla electromagnet. A preliminary design study using NaK seeded nitrogen as the working fluid led to an externally diagonalized segmented MHD channel configuration based on an expendable heat-sink design concept. The current status report includes a review of engineering/design work and performance optimization analyses and summarizes component hardware fabrication and development efforts, preliminary testing results, and recent progress toward full-up assembly and testing

Status of Magnetohydrodynamic Augmented Propulsion Experiment

NASA Technical Reports Server (NTRS)

Litchford, Ron J.; Lineberry, John T.

2007-01-01

Over the past several years, efforts have been under way to design and develop an operationally flexible research facility for investigating the use of cross-field MHD accelerators as a potential thrust augmentation device for thermal propulsion systems, The baseline configuration for this high-power experimental facility utilizes a 1,5-MW, multi-gas arc-heater as a thermal driver for a 2-MW, MHD accelerator, which resides in a large-bore 2-tesla electromagnet. A preliminary design study using NaK seeded nitrogen as the working fluid led to an externally diagonalized segmented MHD channel configuration based on an expendable beat-sink design concept. The current status report includes a review of engineering/design work and performance optimization analyses and summarizes component hardware fabrication and development efforts, preliminary testing results, and recent progress toward full-up assembly and testing

Space Technology Demo at NASA Wallops

NASA Image and Video Library

2017-12-08

A Black Brant IX suborbital sounding rocket is launched at 7:07 p.m., Wednesday October 7, 2015. (NASA Photo/A. Stancil) A Black Brant IX suborbital rocket was launched from NASA's Wallops Flight Facility. The launch occurred at 7:07 p.m. The primary purpose of the flight was to test the performance of the second-stage Black Brant motor. Preliminary indications are that the motor performed as planned. Preliminary data analysis of the technology experiments (vapor tracer deployments) on the payload is in progress. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Space Technology Demo at NASA Wallops

NASA Image and Video Library

2017-12-08

A Black Brant IX suborbital sounding rocket is launched at 7:07 p.m., Wednesday October 7, 2015. (NASA Photo/T. Zaperach) A Black Brant IX suborbital rocket was launched from NASA's Wallops Flight Facility. The launch occurred at 7:07 p.m. The primary purpose of the flight was to test the performance of the second-stage Black Brant motor. Preliminary indications are that the motor performed as planned. Preliminary data analysis of the technology experiments (vapor tracer deployments) on the payload is in progress. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Diffusion of Siderophile Elements in Iron Meteorites

NASA Astrophysics Data System (ADS)

Watson, H. C.; Watson, E. B.

2001-12-01

Preliminary results for diffusion of siderophile elements (Cu, Os, Pd, Re, Os, and Mo) in an iron meteorite analog were obtained at 1400° C and 1GPa from diffusion couple experiments in a piston-cylinder apparatus. Alloys were prepared by synthesizing mixtures of pure metal powders. The alloys were made from a 90 wt% Fe and 10 wt% Ni base mixture, and approximately 1wt% of the various siderophile elements was added (individually) to the same base mixture to make the doped alloys. The powders were packed in pre-drilled holes (~1 mm dia. by 8 mm deep) in MgO cylinders, and run in a piston cylinder apparatus at 1400° C and 1GPa for 48 hours. The resulting homogeneous alloys were then sectioned into wafers approximately 1mm thick, and the faces were polished to prepare for the diffusion experiments. A diffusion couple experiment was conducted by mating a pure alloy wafer and a doped wafer, and placing the couple into an MgO capsule for pressurization and heating in the piston cylinder. The duration of the diffusion experiments ranged from 33 hours to 72 hours. Upon run completion, the diffusion couples were extracted, sectioned lengthwise, and polished for analysis. Diffusion profiles were measured using an electron microprobe. From these experiments it was found that at 1400° C and 1GPa the diffusion coefficient of Os is 1.6E-14 m2/s, the diffusion coefficient of Re is 2.8E-14 m2/s, for Pd it is 9.2E-14 m2/s, for Cu it is 1.2E-13 m2/s, and for Mo it is 2.3E-13 m2/s. These preliminary results raise the possibility that significant diffusive fraction of siderophile elements may occur in metal-silicate systems that fail to equilibrate fully, or under disequilibrium crystallization in pure metal systems.

APPLICATIONS OF LASERS AND OTHER TOPICS IN QUANTUM ELECTRONICS: Laser system based on a commercial microwave oscillator with time compression of a microwave pump pulse

NASA Astrophysics Data System (ADS)

Arteev, M. S.; Vaulin, V. A.; Slinko, V. N.; Chumerin, P. Yu; Yushkov, Yu G.

1992-06-01

An analysis is made of the possibility of using a commercial microsecond microwave oscillator, supplemented by a device for time compression of microwave pulses, in pumping of industrial lasers with a high efficiency of conversion of the pump source energy into laser radiation. The results are reported of preliminary experiments on the commissioning of an excimer XeCl laser.

Application of remote sensing for prediction and detection of thermal pollution

NASA Technical Reports Server (NTRS)

Veziroglu, T. N.; Lee, S. S.

1974-01-01

The first phase is described of a three year project for the development of a mathematical model for predicting thermal pollution by use of remote sensing measurements. A rigid-lid model was developed, and results were obtained for different wind conditions at Biscayne Bay in South Florida. The design of the measurement system was completed, and instruments needed for the first stage of experiment were acquired, tested, and calibrated. A preliminary research flight was conducted.

First Flight of the Advanced Thin Ionization Calorimeter (ATIC) Balloon Experiment

NASA Technical Reports Server (NTRS)

Case, G.; Ellison, S.; Gould, R.; Granger, D.; Guzik, T. G.; Isbert, J.; Price, B.; Stewart, M.; Wefel, J. P.; Mock, L.;

High voltage interactions of a sounding rocket with the ambient and system-generated environments

NASA Technical Reports Server (NTRS)

Kuharski, Robert A.; Jongeward, Gary A.; Wilcox, Katherine G.; Rankin, Thomas V.; Roche, James C.

1990-01-01

EPSAT (environment power system analysis tool) is used to examine the design of SPEAR III, which is scheduled to fly in early 1991. It will test high-voltage designs in both ambient and system-generated environments. Two of the key questions that the experiment hopes to address are whether or not the earth's magnetic field can cause the current that a high-voltage object draws from the plasma to be far less than the current that would be drawn in the absence of the magnetic field and under what neutral environmental conditions a discharge from the high-voltage object to the plasma will occur. The EPSAT program makes it possible to perform a variety of analyses on a preliminary or conceptual-level description of a system in a short period of time. The calculations presented on SPEAR III are all done for a conceptual-level description. The calculations indicate that the experiment will produce the conditions necessary to address these questions.

Development and application of a particle image velocimeter for high-speed flows

NASA Astrophysics Data System (ADS)

Molezzi, M. J.; Dutton, J. C.

1992-01-01

A particle image velocimetry (PIV) system has been developed for use in high-speed separated air flows. The image acquisition system uses two 550 mJ/pulse Nd:YAG lasers and is fully controlled by a host Macintosh computer. The interrogation system is also Macintosh-based and performs interrogations at approximately 2.3 sec/spot and 4.0 sec/spot when using the Young's fringe and autocorrelation methods, respectively. The system has been proven in preliminary experiments using known-displacement simulated PIV photographs and a simple axisymmetric jet flow. Further results have been obtained in a transonic wind tunnel operating at Mach 0.4 to 0.5 (135 m/s to 170 m/s). PIV experiments were done with an empty test section to provide uniform flow data for comparison with pressure and LDV data, then with a two-dimensional base model, revealing features of the von Karman vortex street wake and underlying small scale turbulence.

Proposed Space Flight Experiment Hardware

NASA Technical Reports Server (NTRS)

2003-01-01

The primary thrust for this plan is to develop design tools and fundamental understanding that are timely and consistent with the goal of the various exploration initiatives. The plan will utilize ISS facilities, such as the Fluids Integrated Rack (FIR) and the Microgravity Science Glovebox (MSG). A preliminary flow schematic of Two-Phase Flow Facility (T(phi)FFy) which would utilize FIR is shown in Figure 3. MSG can be utilized to use the Boiling eXperiment Facility (BXF) and Contact Line Dynamics Experiment (CLiDE) Facility. The T(phi)FFy system would have multiple test sections whereby different configurations of heat exchangers could be used to study boiling and condensation phenomena. The test sections would be instrumented for pressure drop, void fraction, heat fluxes, temperatures, high-speed imaging and other diagnostics. Besides a high-speed data acquisition system with a large data storage capability, telemetry could be used to update control and test parameters and download limited amounts of data. In addition, there would be multiple accumulators that could be used to investigate system stability and fluid management issues. The system could accommodate adiabatic tests through either the space station nitrogen supply or have an experiment-specific compressor to pressurize a sufficient amount of air or other non-condensable gas for reuse as the supply bottle is depleted.

Noninvasive Ultrasound Transdermal Insulin Delivery and Glucose Monitoring Using a Low-Profile Cymbal Array

NASA Astrophysics Data System (ADS)

Park, E.-J.; Luis, J.; Meyer, R. J.; Pishko, M. V.; Smith, N. B.

2006-05-01

Recent studies have shown that ultrasound mediated transdermal drug delivery offers promising results for noninvasive drug administration. The purpose of this study was to demonstrate ultrasonic transdermal insulin delivery and in vivo sensing glucose with a novel, low-profile ultrasound array based on the cymbal transducer. As a practical device, the array composed of circular cymbal transducers was thin (< 7mm) and weighed less than 22g. Using this array on hyperglycemic rats, our previous experiments demonstrated that blood glucose would decrease by 296.7 mg/dL from 60 minutes of ultrasound exposure. With a similar intensity, our goal was to evaluate the feasibility of insulin delivery with large animals (rabbits and pigs) and noninvasively determine the glucose level of hyperglycemic rats with the array system. Ultrasound was exposed for 60 minutes at Isptp=100 mW/cm2. With the same procedure, a preliminary experiment of large animal was performed on a pig (12 kg) at Isptp=50 mW/cm2. For the control experiments in insulin delivery, the blood glucose level varied little from the initial baseline. However, for the ultrasound and insulin exposure experiment, the glucose level was found to decrease by 132.6 mg/dL in 60 minutes and continued to decrease by 208.1 mg/dL in 90 minutes. From the preliminary pig experiment, the blood glucose level decreased by 120 mg/dL in 90 minutes. To noninvasively determine the glucose level, ultrasound exposure experiments with an electrochemical glucose biosensor were performed on hyperglycemic rats. After 20 minutes ultrasound exposure, the biosensor was placed at the exposure area to determine the concentration of glucose diffused through the skin. The glucose level of rats determined by the biosensor was 408 mg/dL which was very similar to the results of conventional glucose meter reading 396.7 mg/dL. Recently, a rectangular cymbal transducer was developed to obtain a larger sonication area without an increase in array size. Preliminary experiments were performed on hyperglycemic rabbits to evaluate the new transducer design. The results showed that the rectangular array has enhanced performance compared to the circular array. All results of ultrasound application indicate the feasibility of using a low-cost, light-weight cymbal array for enhanced noninvasive transdermal insulin delivery and glucose monitoring.

Summary of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Spence, E. J.; Nornberg, M. D.; Forest, C. B.

2001-10-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of ~100, and understand the role of fluid turbulence in current generation. Magnetic field generation is possible for only specific flow geometries. We have studied and achieved simple roll flow geometries in a full scale water experiment. Results from this experiment have guided the design of the sodium experiment. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities ~ 15 m/s. A gaussian grid of Hall probes on the surface of the sodium vessel measure the generated external magnetic field. Hall probe feed-thru arrays measure the internal field. Preliminary investigations include measurements of the turbulent electromotive force and excitation of magnetic eigenmodes.

Design of the Madison Dynamo Experiment

NASA Astrophysics Data System (ADS)

Kendrick, R. D.; Bayliss, R. A.; Forest, C. B.; Nornberg, M. D.; O'Connell, R.; Spence, E. J.

2003-10-01

A spherical dynamo experiment has been constructed at the University of Wisconsin's liquid sodium facility. The goals of the experiment are to observe and understand magnetic instabilities driven by flow shear in MHD systems, investigate MHD turbulence for magnetic Reynolds numbers of ˜100, and understand the role of fluid turbulence in current generation. Magnetic field generation is possible for only specific flow geometries. We have studied and achieved simple roll flow geometries in a full scale water experiment. Results from this experiment have guided the design of the sodium experiment. The experiment consists of a 1 m diameter, spherical stainless steel vessel filled with liquid sodium at 110 Celsius. Two 100 Hp motors with impellers drive flows in the liquid sodium with flow velocities ˜ 15 m/s. A grid of Hall probes on the surface of the sodium vessel measure the generated external magnetic field. Hall probe feed-thru arrays measure the internal field. Preliminary investigations include measurements of the turbulent electromotive force and excitation of magnetic eigenmodes.

Preliminary concepts for a solar electric orbit raising experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, R.B.; Penn, J.P.; Janson, S.W.

1989-01-01

Some preliminary concepts for a solar electric orbit raising demonstration that will show technological readiness for the development of operational Electric Orbital Transfer Vehicles (EOTVs) are outlined. These ideas could serve as a template for the proposed Electric Insertion Transfer Experiment (ELITE). At this moment, ELITE is not a funded program. Concepts are presented for a solar electric orbit raising demonstration, for ELITE, and for the path from the proposed ELITE to a future operational EOTV. A brief discussion of the benefits to be derived from the use of EOTVs, the conceptual organization of the ELITE team, the key technologiesmore » for EOTV and ELITE, and some preliminary options for the orbit raising vehicle and representative missions are provided.« less

A preliminary study of the impact of the ERS 1 C band scatterometer wind data on the European Centre for Medium-Range Weather Forecasts global data assimilation system

NASA Technical Reports Server (NTRS)

Hoffman, Ross N.

1993-01-01

A preliminary assessment of the impact of the ERS 1 scatterometer wind data on the current European Centre for Medium-Range Weather Forecasts analysis and forecast system has been carried out. Although the scatterometer data results in changes to the analyses and forecasts, there is no consistent improvement or degradation. Our results are based on comparing analyses and forecasts from assimilation cycles. The two sets of analyses are very similar except for the low level wind fields over the ocean. Impacts on the analyzed wind fields are greater over the southern ocean, where other data are scarce. For the most part the mass field increments are too small to balance the wind increments. The effect of the nonlinear normal mode initialization on the analysis differences is quite small, but we observe that the differences tend to wash out in the subsequent 6-hour forecast. In the Northern Hemisphere, analysis differences are very small, except directly at the scatterometer locations. Forecast comparisons reveal large differences in the Southern Hemisphere after 72 hours. Notable differences in the Northern Hemisphere do not appear until late in the forecast. Overall, however, the Southern Hemisphere impacts are neutral. The experiments described are preliminary in several respects. We expect these data to ultimately prove useful for global data assimilation.

Preliminary design package for prototype solar heating system

NASA Technical Reports Server (NTRS)

1978-01-01

A summary is given of the preliminary analysis and design activity on solar heating systems. The analysis was made without site specific data other than weather; therefore, the results indicate performance expected under these special conditions. Major items include system candidates, design approaches, trade studies and other special data required to evaluate the preliminary analysis and design. The program calls for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test.

A Dual Modality System for Simultaneous Fluorescence and Positron Emission Tomography Imaging of Small Animals

NASA Astrophysics Data System (ADS)

Liu, Shuangquan; Zhang, Bin; Wang, Xin; Li, Lin; Chen, Yan; Liu, Xin; Liu, Fei; Shan, Baoci; Bai, Jing

2011-02-01

A dual-modality imaging system for simultaneous fluorescence molecular tomography (FMT) and positron emission tomography (PET) of small animals has been developed. The system consists of a noncontact 360°-projection FMT module and a flat panel detector pair based PET module, which are mounted orthogonally for the sake of eliminating cross interference. The FMT images and PET data are simultaneously acquired by employing dynamic sampling mode. Phantom experiments, in which the localization and range of radioactive and fluorescence probes are exactly indicated, have been carried out to verify the feasibility of the system. An experimental tumor-bearing mouse is also scanned using the dual-modality simultaneous imaging system, the preliminary fluorescence tomographic images and PET images demonstrate the in vivo performance of the presented dual-modality system.

New observations of Bolivian wind streaks by JPL Airborne SAR: Preliminary results

NASA Technical Reports Server (NTRS)

Blumberg, Dan G.; Greeley, Ronald

1995-01-01

In 1993 NASA's Jet Propulsion Laboratory Airborne Synthetic Aperture Radar system (AIRSAR) was deployed to South America to collect multi-parameter radar data over pre-selected targets. Among the sites targeted was a series of wind streaks located in the Altiplano of Bolivia. The objective of this investigation is to study the effect of wavelength, polarization, and incidence angle on the visibility of wind streaks in radar data. Because this is a preliminary evaluation of the recently acquired data we will focus on one scene and, thus, only on the effects of wavelength and polarization. Wind streaks provide information on the near-surface prevailing winds and on the abundance of winderodible material, such as sand. The potential for a free-flyer radar system that could provide global radar images in multiple wavelengths, polarizations, and incidence angles requires definition of system parameters for mission planning. Furthermore, thousands of wind streaks were mapped from Magellan radar images of Venus; their interpretation requires an understanding of the interaction of radar with wind streaks and the surrounding terrain. Our experiment was conducted on wind streaks in the Altiplano of Bolivia to address these issues.

LDEF Experiment P0006 Linear Energy Transfer Spectrum Measurement (LETSME) quick look report

NASA Technical Reports Server (NTRS)

1990-01-01

A preliminary analysis of the various passive radiation detector materials included in the P0006 LETSME experiment flown on LDEF (Long Duration Exposure Facility) is presented. It consists of four tasks: (1) readout and analysis of thermoluminescent detectors (TLD); (2) readout and analysis of fission foil/mica detectors; (3) readout and analysis of (6)LiF/CR-39 detectors; and (4) preliminary processing and readout of CR-39 and polycarbonate plastic nuclear track detectors (PNTD).

Microwave remote sensing of snow experiment description and preliminary results

NASA Technical Reports Server (NTRS)

Ulaby, F. T. (Principal Investigator); Stiles, W. H.; Hanson, B. C.

1977-01-01

The active and passive microwave responses to snow were investigated at a site near Steamboat Springs, Colorado during the February and March winter months. The microwave equipment was mounted atop truck-mounted booms. Data were acquired at numerous frequencies, polarizations, and angles of incidence for a variety of snow conditions. The experiment description, the characteristics of the microwave and ground truth instruments, and the results of a preliminary analysis of a small portion of the total data volume acquired in Colorado are documented.

A Systems Analysis of the Library and Information Science Statistical Data System: The Preliminary Study. Interim Report.

ERIC Educational Resources Information Center

Hamburg, Morris; And Others

The long-term goal of this investigation is to design and establish a national model for a system of library statistical data. This is a report on The Preliminary Study which was carried out over an 11-month period ending May, 1969. The objective of The Preliminary Study was to design and delimit The Research Investigation in the most efficient…

Automated Iodine Monitoring System Development (AIMS). [shuttle prototype

NASA Technical Reports Server (NTRS)

1975-01-01

The operating principle of the automated iodine monitoring/controller system (AIMS) is described along with several design modifications. The iodine addition system is also discussed along with test setups and calibration; a facsimile of the optical/mechanical portion of the iodine monitor was fabricated and tested. The appendices include information on shuttle prototype AIMS, preliminary prime item development specifications, preliminary failure modes and effects analysis, and preliminary operating and maintenance instructions.

Preliminary Findings of the Photovoltaic Cell Calibration Experiment on Pathfinder Flight 95-3

NASA Technical Reports Server (NTRS)

Vargas-Aburto, Carlos

1997-01-01

The objective of the photovoltaic (PV) cell calibration experiment for Pathfinder was to develop an experiment compatible with an ultralight UAV to predict the performance of PV cells at AM0, the solar spectrum in space, using the Langley plot technique. The Langley plot is a valuable technique for this purpose and requires accurate measurements of air mass (pressure), cell temperature, solar irradiance, and current-voltage(IV) characteristics with the cells directed normal to the direct ray of the sun. Pathfinder's mission objective (95-3) of 65,000 ft. maximum altitude, is ideal for performing the Langley plot measurements. Miniaturization of electronic data acquisition equipment enabled the design and construction of an accurate and light weight measurement system that meets Pathfinder's low payload weight requirements.

Preliminary design package for solar heating and hot water system

NASA Technical Reports Server (NTRS)

1976-01-01

Two prototype solar heating and hot water systems for use in single-family dwellings or commercial buildings were designed. Subsystems included are: collector, storage, transport, hot water, auxiliary energy, and government-furnished site data acquisition. The systems are designed for Yosemite, California, and Pueblo, Colorado. The necessary information to evaluate the preliminary design for these solar heating and hot water systems is presented. Included are a proposed instrumentation plan, a training program, hazard analysis, preliminary design drawings, and other information about the design of the system.

Preliminary Experience of Endovascular Embolization Using N-Butyl Cyanoacrylate for Hemoptysis due to Infectious Pulmonary Artery Pseudoaneurysms via Systemic Arterial Approach.

PubMed

Torikai, Hideyuki; Hasegawa, Ichiro; Jinzaki, Masahiro; Narimatsu, Yoshiaki

2017-10-01

We report 5 patients with hemoptysis due to infectious pulmonary artery pseudoaneurysm (PAP) treated with endovascular embolization using N-butyl cyanoacrylate (NBCA) injected via bronchial and nonbronchial systemic arterial approaches. Infectious diseases included inactive tuberculosis (n = 3), nontuberculous mycobacteriosis (n = 1), and chronic infection of unknown origin (n = 1). Seven PAPs were detected on selective systemic angiography, and injection of NBCA was performed. Disappearance of all PAPs was confirmed on systemic arteriography after the intervention. In all patients, hemoptysis was stopped without major complications, and it did not recur during the follow-up period (mean, 351 d; range, 285-427 d). Copyright © 2016 SIR. Published by Elsevier Inc. All rights reserved.

Preliminary results from a simulated laboratory experiment or an encounter of cluster satellite probes with a reconnection layer

NASA Astrophysics Data System (ADS)

Yamada, M.; Ren, Y.; Ji, H.; Gerhardt, S.; Darfman, S.

2006-12-01

With the recent upgrade of the MRX (Magnetic Reconnection Experiment) device[1], our experimental operation allows us to carry out a jog experiment in which a current sheet can be moved swiftly across an inserted probe assembly. A cluster of probes with variable distances can be inserted into a known desired position in the MRX device. This setup can be similar to the situation in which a cluster of satellites encounters a rapidly moving reconnection layer. If necessary, we can create a neutral sheet where the density of one side is significantly higher than the other, as is the case for the magnetopause. A variable guide field will be applied to study its effect on reconnection. We proposed[2] to document basic patterns of data during a simulated encounter of the MRX reconnection layer with the four-probe mock-up system and compare them with data acquired from past satellites. Relative position of the MMS satellites in the magnetosphere can then be determined. Optimum cluster configuration or distance between the four satellites can be determined for various diagnostics or research missions. The relationship of magnetic fluctuations[3] with the observed out-of- plane quadrupole field, a characteristic signature of the Hall MHD, can be also studied in this series of experiments. In this paper, results from a preliminary experiment will be presented. These experiments utilize effectively the unique MRX ability to accurately know the location of diagnostics with respect to the moving reconnection layer. Supported by DoE, NASA, NSF. [1] M. Yamada et al, Phys. Plasmas 13, 052119 (2006), [2] M.Yamada et al, MMS-IDS proposal (2006), [3] H. Ji et al, Phys. Rev. Letts. 92, 115001 (2004)

Preliminary test results from the CELSS Test Facility Engineering Development Unit

NASA Technical Reports Server (NTRS)

Kliss, Mark H.; Macelroy, R. D.; Blackwell, C. C.; Borchers, B. A.; Drews, M. E.; Longabaugh, J. R.; Yendler, B. S.; Zografos, A. I.

1994-01-01

As part of the NASA Controlled Ecological Life Support System (CELSS) Program, a CELSS Test Facility (CTF) is being planned for installation on the Space Station. The CTF will be used to provide data on the productivity and efficiency of a variety of CELSS higher plant crops grown in the microgravity environment of the Space Station. Tight environmental control will be maintained while data on gas exchange rates and biomass accumulation rates are collected. In order to obtain an early realistic determination of the subsystem and system requirements necessary to provide the environmental conditions specified for CTF crop productivity experiments, an Engineering Development Unit (EDU) has been designed, constructed and is in the process of subsystem and system testing at NASA Ames Research Center. The EDU is a ground test-bed which will be used to characterize the integrated performance of major subsystem technologies, to evaluate hardware candidates and control strategies required for the CTF, and to further define the ability to meet CTF requirements within present Space Station constraints. This paper reviews the functional requirements for the EDU, and focuses on the performance evaluation and test results of the various subsystems. Preliminary integrated performance results and control system operation are addressed, and plans for future science and technology testing are discussed.

High Altitude Long Endurance (HALE) Unmanned Aircraft System (UAS): Pilot Knowledge, Skills and Abilities

NASA Technical Reports Server (NTRS)

2005-01-01

This report summarizes the initial work accomplished by the ACCESS 5 Human System Integration (HSI) team to identify Unmanned Aircraft System (UAS) Pilot Knowledge, Skill and Ability (KSA), Training and Medical requirements. To derive this information the following tasks were accomplished: a) Mission and Function analyses were performed; b) Applicable FARs and FAA Advisory Circulars (ACs) were reviewed; c) Meetings were conducted with NASA and FAA Human Factors personnel; d) Surveys were completed by ACCESS 5 HSI Working group UA Pilots; e) Coordination meetings were conducted with the ACCESS 5 Policy IPT. The results of these efforts were used to develop a summary of the current qualifications. for an individual to function as a Pilot In Command (PIC) for UAs currently flown by UNITE companies, to develop preliminary Pilot KSAs for each phase of flight, and to delineate preliminary Pilot Training and Medical requirements. These results are to be provided to the Policy IPT to support their development of recommendations for UA Pilot Rating Criteria, training and medical qualifications. It is expected that the initially an instrument rated pilot will be required to serve as the PIC. However, as operational experience is gained, and automation is applied to accomplish various system functions, it is expected that pilot rating criteria could be lessened.

Preliminary design activities for solar heating and cooling systems

NASA Technical Reports Server (NTRS)

1978-01-01

Information on the development of solar heating and cooling systems is presented. The major emphasis is placed on program organization, system size definition, site identification, system approaches, heat pump and equipment design, collector procurement, and other preliminary design activities.

Preliminary basic performance analysis of the Cedar multiprocessor memory system

NASA Technical Reports Server (NTRS)

Gallivan, K.; Jalby, W.; Turner, S.; Veidenbaum, A.; Wijshoff, H.

1991-01-01

Some preliminary basic results on the performance of the Cedar multiprocessor memory system are presented. Empirical results are presented and used to calibrate a memory system simulator which is then used to discuss the scalability of the system.

Carbon Nanotube Based Nano-Electro-Mechanical Systems (NEMS)

NASA Technical Reports Server (NTRS)

Han, Jie; Dai, Hongjie; Saini, Subhash

1998-01-01

Carbon nanotubes (CNT) enable nanoelectromechanical systems (NEMS) because of their inherent nanostructure, intrinsic electric conductivity and mechanical resilience. The collaborative work between Stanford (experiment) and NASA Ames (theory and simulation) has made progress in two types of CNT based NEMS for nanoelectronics and sensor applications. The CNT tipped scanning probe microscopy (SPM) is a NEMS in which CNT tips are used for nanoscale probing, imaging and manipulating. It showed great improvement in probing surfaces and biological systems over conventional tips. We have recently applied it to write (lithography) and read (image) uniform SiO2 lines on large Si surface area at speed up to 0.5 mm per s. Preliminary work using approximately 10 nm multiwall nanotube tips produced approximately 10 nm structures and showed that the CNT tips didn't wear down when crashed as conventional tips often do. This presents a solution to the long standing tip-wear problem in SPM nanolithography. We have also explored potential of CNT tips in imaging DNA in water. Preliminary experiment using 10 nm CNT tips reached 5 nm resolution. The 1 nm nanolithography and 1 nm DNA imaging can be expected by using approximately 1 nm CNT tips. In contrast to CNT tipped SPM, we also fabricated CNT devices on silicon wafer in which CNTs connect patterned metallic lines on SiO2/Si by a simple chemical vapor deposition process. Using conventional lithography for silicon wafer, we have been able to obtain CNT based transistors and sensors. Investigations of the CNT NEMS as physical, biological and chemical sensors are in progress and will be discussed.

Preliminary results and power analysis of the UAH SEDS G503 GAS can

NASA Technical Reports Server (NTRS)

Jalbert, Lyle B.; Mustaikis, Steven, II; Nerren, Philip

1995-01-01

The G-503 Get Away Special (GAS) Canister contained four experiments. A stainless steel corrosion experiment, and experiment to mix and cure concrete, a plant root growth chamber, and a group of 8 chambers to characterize diatom growth cycles in microgravity. As would be expected for this selection of experiments a significant amount of power was required to carry out these investigations over several days in a GAS environment. This was accomplished through the use of low power experiment control circuitry, heaters, and an estimate 3.6 kWh battery pack. The battery was designed around 120 standard Duracell Alkaline F cells. This pack weighed 29.5 kg (65 lbs) including a DC/DC converter and the power distribution bus for all of the experiments. Although not rechargeable, this configurations was a fraction of the cost of rechargeable systems and did not require venting to the outside of the can. Combining this with the long term storage performance, 85% of initial capacity after four years at 20 C (70 F), this guarantees sufficient power even with unexpected launch delays. This paper describes the experiments, there operation and initial results. Also, the performance of the power system during the STS-68 SRL2 mission will be addressed.

The JINR Tier1 Site Simulation for Research and Development Purposes

NASA Astrophysics Data System (ADS)

Korenkov, V.; Nechaevskiy, A.; Ososkov, G.; Pryahina, D.; Trofimov, V.; Uzhinskiy, A.; Voytishin, N.

2016-02-01

Distributed complex computing systems for data storage and processing are in common use in the majority of modern scientific centers. The design of such systems is usually based on recommendations obtained via a preliminary simulated model used and executed only once. However big experiments last for years and decades, and the development of their computing system is going on, not only quantitatively but also qualitatively. Even with the substantial efforts invested in the design phase to understand the systems configuration, it would be hard enough to develop a system without additional research of its future evolution. The developers and operators face the problem of the system behaviour predicting after the planned modifications. A system for grid and cloud services simulation is developed at LIT (JINR, Dubna). This simulation system is focused on improving the effciency of the grid/cloud structures development by using the work quality indicators of some real system. The development of such kind of software is very important for making a new grid/cloud infrastructure for such big scientific experiments like the JINR Tier1 site for WLCG. The simulation of some processes of the Tier1 site is considered as an example of our application approach.

Study methods for disinfection water for injection

NASA Astrophysics Data System (ADS)

Grishkanich, Alexander; Zhevlakov, Alexander; Kascheev, Sergey; Polyakov, Vladimir; Sidorov, Igor; Ruzankina, Julia; Yakovlev, Alexey; Mak, Andrey

2016-04-01

Experimental results presented in this study tends to explore viruses in the water for their further decontamination under the influence of laser radiation (λ=220-390 nm). Conducted a series of experiments to study the dependence of water quality from the effects of laser radiation. Correlation between degree of survival of viruses and power density. The results showed that all the analyzed samples of water is clearing from bacteria to 98%. Preliminary tests of the prototype laboratory system UFOVI has opened up new opportunities for water sterilizing.

Reconstruction of coded aperture images

NASA Technical Reports Server (NTRS)

Bielefeld, Michael J.; Yin, Lo I.

1987-01-01

Balanced correlation method and the Maximum Entropy Method (MEM) were implemented to reconstruct a laboratory X-ray source as imaged by a Uniformly Redundant Array (URA) system. Although the MEM method has advantages over the balanced correlation method, it is computationally time consuming because of the iterative nature of its solution. Massively Parallel Processing, with its parallel array structure is ideally suited for such computations. These preliminary results indicate that it is possible to use the MEM method in future coded-aperture experiments with the help of the MPP.

Cone-beam reconstruction for the two-circles-plus-one-line trajectory

NASA Astrophysics Data System (ADS)

Lu, Yanbin; Yang, Jiansheng; Emerson, John W.; Mao, Heng; Zhou, Tie; Si, Yuanzheng; Jiang, Ming

2012-05-01

The Kodak Image Station In-Vivo FX has an x-ray module with cone-beam configuration for radiographic imaging but lacks the functionality of tomography. To introduce x-ray tomography into the system, we choose the two-circles-plus-one-line trajectory by mounting one translation motor and one rotation motor. We establish a reconstruction algorithm by applying the M-line reconstruction method. Numerical studies and preliminary physical phantom experiment demonstrate the feasibility of the proposed design and reconstruction algorithm.

First Trial of Real-time Poloidal Beta Control in KSTAR

NASA Astrophysics Data System (ADS)

Han, Hyunsun; Hahn, S. H.; Bak, J. G.; Walker, M. L.; Woo, M. H.; Kim, J. S.; Kim, Y. J.; Bae, Y. S.; KSTAR Team

2014-10-01

Sustaining the plasma in a stable and a high performance condition is one of the important control issues for future steady state tokamaks. In the 2014 KSTAR campaign, we have developed a real-time poloidal beta (βp) control technique and carried out preliminary experiments to identify its feasibility. In the control system, the βp is calculated in real time using the measured diamagnetic loop signal (DLM03) with coil pickup corrections, and compared with the target value leading to the change of the neutral beam (NB) heating power using a feedback PID control algorithm. To match the required power of NB which is operated with constant voltage, the duty cycles of the modulation were adjusted as the ratio of the required power to the maximum achievable one. This paper will present the overall procedures of the βp control, the βp estimation process implemented in the plasma control system, and the analysis on the preliminary experimental results. This work is supported by the KSTAR research project funded by the Ministry of Science, ICT & Future Planning of Korea.

Preliminary experience on the use of the Adnatest® system for detection of circulating tumor cells in prostate cancer patients.

PubMed

Todenhöfer, Tilman; Hennenlotter, Jörg; Feyerabend, Susan; Aufderklamm, Stefan; Mischinger, Johannes; Kühs, Ursula; Gerber, Valentina; Fetisch, Jasmin; Schilling, David; Hauch, Siegfried; Stenzl, Arnulf; Schwentner, Christian

2012-08-01

The Adnatest® system combines immunomagnetic enrichment of epithelial cells with polymerase chain reaction for prostate cancer (PC)-specific transcripts for the detection circulating tumor cells (CTCs). We evaluated the Adnatest® in patients with castration-resistant PC receiving docetaxel chemotherapy. CTCs were assessed in 16 patients with castration-resistant PC before cycles one and three of chemotherapy. Furthermore, markers of stem cells and epithelial-mesenchymal transition were assessed. Treatment response was assessed by imaging and prostate-specific antigen measurements. Before chemotherapy, 11 patients were Adnatest®-positive whereas five patients were Adnatest®-positive before cycle three. A positive Adnatest® correlated with radiological progression (p=0.02). Rates of disease progression in epidermal growth factor receptor (EGFR)-positive and -negative patients were 100% and 7.7% (p=0.03). In this preliminary study, the Adnatest® detected CTCs in a considerable proportion of patients with castration-resistant PC. First data on certain markers (EGFR and aldehyd dehydrogenase 1) encourage future studies investigating transcripts predicting treatment response.

The Development of a Conceptual Framework and Preliminary Item Bank for Childbirth-Specific Patient-Reported Outcome Measures.

PubMed

Korst, Lisa M; Fridman, Moshe; Saeb, Samia; Greene, Naomi; Fink, Arlene; Gregory, Kimberly D

2018-05-24

To develop a conceptual framework and preliminary item bank for childbirth-specific patient-reported outcome (PRO) domains. Women, who were U.S. residents, ≥18 years old, and ≥20 weeks pregnant, were surveyed regarding their childbirth values and preferences (V&P) using online panels. Using community-based research techniques and Patient-Reported Outcomes Management Information System (PROMIS ® ) methodology, we conducted a comprehensive literature review to identify self-reported survey items regarding patient-reported V&P and childbirth experiences and outcomes (PROs). The V&P/PRO domains were validated by focus groups. We conducted a cross-sectional observational study and fitted a multivariable logistic regression model to each V&P item to describe "who" wanted each item. We identified 5,880 V&P/PRO items that mapped to 19 domains and 58 subdomains. We present results for the 2,250 survey respondents who anticipated a vaginal delivery in a hospital. Wide variation existed regarding each V&P item, and personal characteristics, such as maternal confidence and ability to cope well with pain, were frequent predictors in the models. The resulting preliminary item bank consisted of 60 key personal characteristics and 63 V&P/PROs. The conceptual framework and preliminary (PROMIS ® ) item bank presented here provide a foundation for the development of childbirth-specific V&P/PROs. © Health Research and Educational Trust.

Fetoscopic single-layer repair of open spina bifida using a cellulose patch: preliminary clinical experience.

PubMed

Pedreira, Denise A L; Zanon, Nelci; de Sá, Renato A M; Acacio, Gregório L; Ogeda, Edilson; Belem, Teresa M L O U; Chmait, Ramen H; Kontopoulos, Eftichia; Quintero, Ruben A

2014-11-01

To report our preliminary clinical experience in the antenatal correction of open spina bifida (OSB) using a fetoscopic approach and a simplified closure technique. Four fetuses with lumbar-sacral defects were operated in utero from 25 to 27 weeks. Surgeries were performed percutaneously under general anesthesia using three trocars and partial carbon dioxide insufflation. After dissection of the neural placode, the surrounding skin was closed over a cellulose patch using a single continuous stitch. Surgical closure was successful in three of the four cases. All successful cases showed improvement of the hindbrain herniation and no neonatal neurosurgical repair was required in two cases. Delivery occurred between 31 and 33 weeks, and no fetal or neonatal deaths occurred. Ventriculoperitoneal shunting was not needed in two out of the 3 successful cases. Our preliminary experience suggests that definitive fetoscopic repair of OSB is feasible using our innovative surgical technique. A phase I trial for the fetoscopic correction of OSB with this technique is currently being conducted.

Evaluation and Preliminary Results of the New USNO PPS Timing Receiver

DTIC Science & Technology

2000-11-01

timing receiver, one may currently obtain raw pseudorange and carrier-phase data by periodically downloading such data from a flashcard . Several...preliminary experiments have been performed using data collected from the prototype TTR- 12 receivers’ flashcards and geodetic GPS carrier-phase techniques

The Clinical/Practicum Experience in Professional Preparation: Preliminary Findings

ERIC Educational Resources Information Center

Ralph, Edwin George; Walker, Keith; Wimmer, Randy

2008-01-01

The authors synthesize preliminary findings from an interdisciplinary study of the practicum/clinical phase of undergraduate pre-service education in the professions. Early data analysis identified similarities and differences across disciplines in terms of: (a) the terminology describing each practicum program, (b) the programs' key…

The engineering design of the Tokamak Physics Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmidt, J.A.

A mission and supporting physics objectives have been developed, which establishes an important role for the Tokamak Physics Experiment (TPX) in developing the physic basis for a future fusion reactor. The design of TPX include advanced physics features, such as shaping and profile control, along with the capability of operating for very long pulses. The development of the superconducting magnets, actively cooled internal hardware, and remote maintenance will be an important technology contribution to future fusion projects, such as ITER. The Conceptual Design and Management Systems for TPX have been developed and reviewed, and the project is beginning Preliminary Design.more » If adequately funded the construction project should be completed in the year 2000.« less

(n,xn) cross section measurements for Y-89 foils used as detectors for high energy neutron measurements in the deeply subcritical assembly "QUINTA"

NASA Astrophysics Data System (ADS)

Bielewicz, Marcin; Kilim, Stanisław; Strugalska-Gola, Elżbieta; Szuta, Marcin; Wojciechowski, Andrzej; Tyutyunnikov, Sergey; Prokofiev, Alexander; Passoth, Elke

2017-09-01

Study of the deep subcritical systems (QUINTA) using relativistic beams is performed within the project "Energy and Transmutation of Radioactive Wastes" (E&T - RAW). The experiment assembly was irradiated by deuteron/proton beam (Dubna NUCLOTRON). We calculated the neutron energy spectrum inside the whole assembly by using threshold energy (n,xn) reactions in yttrium (Y-89) foils. There are almost no experimental cross section data for those reactions. New Y-89(n,xn) cross section measurements were carried out at The Svedberg laboratory (TSL) in Uppsala, Sweden in 2015. In this paper we present preliminary results of those experiments.

Rheological properties, shape oscillations, and coalescence of liquid drops with surfactants

NASA Technical Reports Server (NTRS)

Apfel, R. E.; Holt, R. G.

1990-01-01

A method was developed to deduce dynamic interfacial properties of liquid drops. The method involves measuring the frequency and damping of free quadrupole oscillations of an acoustically levitated drop. Experimental results from pure liquid-liquid systems agree well with theoretical predictions. Additionally, the effects of surfactants is considered. Extension of these results to a proposed microgravity experiment on the drop physics module (DPM) in USML-1 are discussed. Efforts are also underway to model the time history of the thickness of the fluid layer between two pre-coalescence drops, and to measure the film thickness experimentally. Preliminary results will be reported, along with plans for coalescence experiments proposed for USML-1.

Between disorder and order: A case study of power law

NASA Astrophysics Data System (ADS)

Cao, Yong; Zhao, Youjie; Yue, Xiaoguang; Xiong, Fei; Sun, Yongke; He, Xin; Wang, Lichao

2016-08-01

Power law is an important feature of phenomena in long memory behaviors. Zipf ever found power law in the distribution of the word frequencies. In physics, the terms order and disorder are Thermodynamic or statistical physics concepts originally and a lot of research work has focused on self-organization of the disorder ingredients of simple physical systems. It is interesting what make disorder-order transition. We devise an experiment-based method about random symbolic sequences to research regular pattern between disorder and order. The experiment results reveal power law is indeed an important regularity in transition from disorder to order. About these results the preliminary study and analysis has been done to explain the reasons.

Next generation 9-1-1 system : preliminary concept of operations.

DOT National Transportation Integrated Search

2005-12-01

The purpose of this document is to provide a preliminary Concept of Operations for the : Next Generation (NG9-1-1) system (or system of systems). The U.S. Department of : Transportation (DOT) understands that access to emergency services provid...

Modified stretched exponential model of computer system resources management limitations-The case of cache memory

NASA Astrophysics Data System (ADS)

Strzałka, Dominik; Dymora, Paweł; Mazurek, Mirosław

2018-02-01

In this paper we present some preliminary results in the field of computer systems management with relation to Tsallis thermostatistics and the ubiquitous problem of hardware limited resources. In the case of systems with non-deterministic behaviour, management of their resources is a key point that guarantees theirs acceptable performance and proper working. This is very wide problem that stands for many challenges in financial, transport, water and food, health, etc. areas. We focus on computer systems with attention paid to cache memory and propose to use an analytical model that is able to connect non-extensive entropy formalism, long-range dependencies, management of system resources and queuing theory. Obtained analytical results are related to the practical experiment showing interesting and valuable results.

Using the Light Microscopy Module (LMM) on the International Space Station (ISS), The Advanced Colloids Experiment (ACE) and MacroMolecular Biophysics (MMB)

NASA Technical Reports Server (NTRS)

Meyer, William; Foster, William M.; Motil, Brian J.; Sicker, Ronald; Abbott-Hearn, Amber; Chao, David; Chiaramonte, Fran; Atherton, Arthur; Beltram, Alexander; Bodzioney, Christopher M.;

Protein crystal growth in a microgravity environment

NASA Technical Reports Server (NTRS)

Bugg, Charles E.

1988-01-01

Protein crystal growth is a major experimental problem and is the bottleneck in widespread applications of protein crystallography. Research efforts now being pursued and sponsored by NASA are making fundamental contributions to the understanding of the science of protein crystal growth. Microgravity environments offer the possibility of performing new types of experiments that may produce a better understanding of protein crystal growth processes and may permit growth environments that are more favorable for obtaining high quality protein crystals. A series of protein crystal growth experiments using the space shuttle was initiated. The first phase of these experiments was focused on the development of micro-methods for protein crystal growth by vapor diffusion techniques, using a space version of the hanging drop method. The preliminary space experiments were used to evolve prototype hardware that will form the basis for a more advanced system that can be used to evaluate effects of gravity on protein crystal growth.

CORRTEX Diagnostic Deployment for the SPE-III experiment, 24 July 2012: Fielding Report and Preliminary Data Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandoval, Thomas D.; Schultz-Fellenz, Emily S.

2012-08-29

The Continuous Reflectometry for Radius vs Time Experiments (CORRTEX) diagnostic system was deployed for the third explosives test in the Source Physics Experiment (SPE) sequence to monitor and verify several conditions of the experiment including the detonation velocity of the explosive package and functioning of explosive initiators. Six distance-marked coaxial cables were installed on the SPE-III explosives canister, and key locations documented through along-cable length measurements and photography. CORRTEX uses electrical-pulse time-domain reflectometry to continuously record the two-way transit time (TWTT) of the cables. As the shock front of the detonation advances, the coaxial cable is shorted or destroyed, andmore » the resulting TWTT also decreases. Interpretation of these changes as a function of TWTT can be converted to positional measurements using known parameters of the cables.« less

Morpho-dynamics of mountain streams: from laboratory experiments to field observations

NASA Astrophysics Data System (ADS)

Mettra, François; Lane, Stuart Nicholas; Heyman, Joris; Ancey, Christophe

2017-04-01

Due to the complexity of mountain stream evolution and its causes, it is judicious to conduct flume experiments to better understand the morpho-dynamics of steep river channels. A series of long-term experiments under steady conditions revealed the high internal variability of transport processes (including erosion and deposition events). In particular, high fluctuations over time of the sediment volume stored in the channel (or released from the channel) were observed for the steepest channel experiments at intermittent transport conditions. These conditions imply an autogenic regulation of the sediment transport process. When these were extended to non-steady conditions, repeated flood events suggested a hysteresis effect on sediment transport but where the forcing frequency (of the repeated floods) plays an important role in the response of the channel system. The results are compared with preliminary field observations from continuous measurements in Swiss Alpine rivers. Simple mechanisms of steep river channel behavior are proposed.

A Novel Method of Autonomous Inspection for Transmission Line based on Cable Inspection Robot LiDAR Data

PubMed Central

Qin, Xinyan; Wu, Gongping; Fan, Fei; Ye, Xuhui; Mei, Quanjie

2018-01-01

With the growth of the national economy, there is increasing demand for electricity, which forces transmission line corridors to become structurally complicated and extend to complex environments (e.g., mountains, forests). It is a great challenge to inspect transmission line in these regions. To address these difficulties, a novel method of autonomous inspection for transmission line is proposed based on cable inspection robot (CIR) LiDAR data, which mainly includes two steps: preliminary inspection and autonomous inspection. In preliminary inspection, the position and orientation system (POS) data is used for original point cloud dividing, ground point filtering, and structured partition. A hierarchical classification strategy is established to identify the classes and positions of the abnormal points. In autonomous inspection, CIR can autonomously reach the specified points through inspection planning. These inspection targets are imaged with PTZ (pan, tilt, zoom) cameras by coordinate transformation. The feasibility and effectiveness of the proposed method are verified by test site experiments and actual line experiments, respectively. The proposed method greatly reduces manpower and improves inspection accuracy, providing a theoretical basis for intelligent inspection of transmission lines in the future. PMID:29462865

Preliminary results for a higher-precision measurement of the helium n=2 triplet P fine structure

NASA Astrophysics Data System (ADS)

Kato, K.; Skinner, T. D. G.; George, M. C.; Fitzakerley, D. W.; Vutha, A. C.; Storry, C. H.; Bezginov, N.; Valdez, T.; Hessels, E. A.

2017-04-01

Preliminary results for a higher-precision measurement of the n=2 triplet P J=1 to J=2 fine-structure interval in atomic helium are presented. A beam of metastable helium atoms is created in a liquid-nitrogen-cooled dc-discharge source, and is intensified using a 2D-MOT. These atoms are excited to the 2 triplet P state, and undergo a frequency-offset separated-oscillatory-field (FOSOF) microwave experiment. Only atoms which undergo a microwave transition, in the time-separated microwave fields are laser-excited to a Rydberg state and then Stark ionized and counted. Our new experimental design has eliminated the major systematic effects of previous experiments, and has led to a substantial improvement in the signal-to-noise ratio of the collected data. Our final improved measurement (with an expected uncertainty of less than 100 Hz) will allow for a test of 2-electron QED-theory in the helium n=2 triplet P system, and will be an important step towards obtaining a precise determination of the fine-structure constant. This research is supported by NSERC, CRC, CFI and NIST.

Ultraviolet Free Electron Laser Facility preliminary design report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben-Zvi, I.

1993-02-01

This document, the Preliminary Design Report (PDR) for the Brookhaven Ultraviolet Free Electron Laser (UV FEL) facility, describes all the elements of a facility proposed to meet the needs of a research community which requires ultraviolet sources not currently available as laboratory based lasers. Further, for these experiments, the requisite properties are not extant in either the existing second or upcoming third generation synchrotron light sources. This document is the result of our effort at BNL to identify potential users, determine the requirements of their experiments, and to design a facility which can not only satisfy the existing need, butmore » have adequate flexibility for possible future extensions as need dictates and as evolving technology allows. The PDR is comprised of three volumes. In this, the first volume, background for the development of the proposal is given, including descriptions of the UV FEL facility, and representative examples of the science it was designed to perform. Discussion of the limitations and potential directions for growth are also included. A detailed description of the facility design is then provided, which addresses the accelerator, optical, and experimental systems. Information regarding the conventional construction for the facility is contained in an addendum to volume one (IA).« less

Synthetic aperture ultrasound imaging with a ring transducer array: preliminary ex vivo results.

PubMed

Qu, Xiaolei; Azuma, Takashi; Yogi, Takeshi; Azuma, Shiho; Takeuchi, Hideki; Tamano, Satoshi; Takagi, Shu

2016-10-01

The conventional medical ultrasound imaging has a low lateral spatial resolution, and the image quality depends on the depth of the imaging location. To overcome these problems, this study presents a synthetic aperture (SA) ultrasound imaging method using a ring transducer array. An experimental ring transducer array imaging system was constructed. The array was composed of 2048 transducer elements, and had a diameter of 200 mm and an inter-element pitch of 0.325 mm. The imaging object was placed in the center of the ring transducer array, which was immersed in water. SA ultrasound imaging was then employed to scan the object and reconstruct the reflection image. Both wire phantom and ex vivo experiments were conducted. The proposed method was found to be capable of producing isotropic high-resolution images of the wire phantom. In addition, preliminary ex vivo experiments using porcine organs demonstrated the ability of the method to reconstruct high-quality images without any depth dependence. The proposed ring transducer array and SA ultrasound imaging method were shown to be capable of producing isotropic high-resolution images whose quality was independent of depth.

Preliminary System Design of the SWRL Financial System.

ERIC Educational Resources Information Center

Ikeda, Masumi

The preliminary system design of the computer-based Southwest Regional Laboratory's (SWRL) Financial System is outlined. The system is designed to produce various management and accounting reports needed to maintain control of SWRL operational and financial activities. Included in the document are descriptions of the various types of system…

Space Technology Demo at NASA Wallops

NASA Image and Video Library

2017-12-08

A vapor cloud is seen after launch of a Black Brant IX suborbital sounding rocket, launched at 7:07 p.m., Wednesday October 7, 2015. (NASA Photo/J. Adkins) A Black Brant IX suborbital rocket was launched from NASA's Wallops Flight Facility. The launch occurred at 7:07 p.m. The primary purpose of the flight was to test the performance of the second-stage Black Brant motor. Preliminary indications are that the motor performed as planned. Preliminary data analysis of the technology experiments (vapor tracer deployments) on the payload is in progress. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

RF tomography of metallic objects in free space: preliminary results

NASA Astrophysics Data System (ADS)

Li, Jia; Ewing, Robert L.; Berdanier, Charles; Baker, Christopher

2015-05-01

RF tomography has great potential in defense and homeland security applications. A distributed sensing research facility is under development at Air Force Research Lab. To develop a RF tomographic imaging system for the facility, preliminary experiments have been performed in an indoor range with 12 radar sensors distributed on a circle of 3m radius. Ultra-wideband pulses are used to illuminate single and multiple metallic targets. The echoes received by distributed sensors were processed and combined for tomography reconstruction. Traditional matched filter algorithm and truncated singular value decomposition (SVD) algorithm are compared in terms of their complexity, accuracy, and suitability for distributed processing. A new algorithm is proposed for shape reconstruction, which jointly estimates the object boundary and scatter points on the waveform's propagation path. The results show that the new algorithm allows accurate reconstruction of object shape, which is not available through the matched filter and truncated SVD algorithms.

The Preliminary Design of a Universal Martian Lander

NASA Technical Reports Server (NTRS)

Norman, Timothy L.; Gaskin, David; Adkins, Sean; MacDonnell, David; Ross, Enoch; Hashimoto, Kouichi; Miller, Loran; Sarick, John; Hicks, Jonathan; Parlock, Andrew;

The Majorana Demonstrator Status and Preliminary Results

DOE PAGES

Yu, C. -H.; Alvis, S. I.; Arnquist, I. J.; ...

2018-01-01

The MAJORANA Collaboration is using an array of high-purity Ge detectors to search for neutrinoless double-beta decay in 76Ge. Searches for neutrinoless double-beta decay are understood to be the only viable experimental method for testing the Majorana nature of the neutrino. Observation of this decay would imply violation of lepton number, that neutrinos are Majorana in nature, and provide information on the neutrino mass. The MAJORANA DEMONSTRATOR comprises 44.1 kg of p-type point-contact Ge detectors (29.7 kg enriched in 76Ge) surrounded by a low-background shield system. The experiment achieved a high efficiency of converting raw Ge material to detectors andmore » an unprecedented detector energy resolution of 2.5 keV FWHM at Q ββ. The MAJORANA collaboration began taking physics data in 2016. Here, this paper summarizes key construction aspects of the Demonstrator and shows preliminary results from initial data.« less

The First Flight of ATIC : Preliminary Results on CNO Nuclei

NASA Technical Reports Server (NTRS)

Fazely, A.; Gunasingha, R.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

We present preliminary results on the spectra of CNO nuclei in the cosmic radiation as measured in the first flight of the Advanced Thin Ionization Calorimeter Balloon Experiment (ATIC) which lasted for 16 days, starting in December, 2000 with a launch from McMurdo, Antarctica. ATIC is a multiple, long duration balloon flight,investigation for the study of cosmic ray spectra from below 50 GeV to near 100 TeV total energy, using a fully active Bismuth Germanate (BGO) calorimeter. It is equipped with the first large area mosaic of small fully depleted silicon detector pads capable of charge identification in cosmic rays from H to Fe. As a redundancy check for the charge identification and a coarse particle tracking system, three projective layers of x-y scintillator hodoscopes were employed, above, in the center and below a Carbon interaction'target'.

Magnetic Field Observations near Venus: Preliminary Results from Mariner 10.

PubMed

Ness, N F; Behannon, K W; Lepping, R P; Whang, Y C; Schatten, K H

1974-03-29

The NASA-GSFC magnetic field experiment on Mariner 10 is the first flight of a dual magnetometer system conceived to permit accurate measurements of weak magnetic fields in space in the presence of a significant and variable spacecraft magnetic field. Results from a preliminary analysis of a limted data set are summarized in this report, which is restricted primarily to Venus encounter. A detached bow shock wave that develops as the super Alfvénic solar wind interacts with the Venusian atmosphere has been observed. However, the unique coincidence of trajectory position and interplanetary field orientation at the time of bow shock crossing led to a very disturbed shock profile with considerably enhanced upstream magnetic fluctuations. At present it is not possible to ascertain the nature and characteristics of the obstacle responsible for deflecting the solar wind flow. Far downstream disturbances associated with the solar wind wake have been observed.

Preliminary study of the effects of a reversible chemical reaction on gas bubble dissolution. [for space glass refining

NASA Technical Reports Server (NTRS)

Weinberg, M. C.

1982-01-01

A preliminary investigation is carried out of the effects of a reversible chemical reaction on the dissolution of an isolated, stationary gas bubble in a glass melt. The exact governing equations for the model system are formulated and analyzed. The approximate quasi-steady-state version of these equations is solved analytically, and a calculation is made of bubble dissolution rates. The results are then compared with numerical solutions obtained from the finite difference form of the exact governing equations. It is pointed out that in the microgravity condition of space, the buoyant rise of a gas bubble in a glass melt will be negligible on the time scale of most experiments. For this reason, a determination of the behavior of a stationary gas bubble in a melt is relevant for an understanding of glass refining in space.

The Majorana Demonstrator Status and Preliminary Results

NASA Astrophysics Data System (ADS)

Yu, C.-H.; Alvis, S. I.; Arnquist, I. J.; Avignone, F. T.; Barabash, A. S.; Barton, C. J.; Bertrand, F. E.; Bode, T.; Brudanin, V.; Busch, M.; Buuck, M.; Caldwell, T. S.; Chan, Y.-D.; Christofferson, C. D.; Chu, P.-H.; Cuesta, C.; Detwiler, J. A.; Dunagan, C.; Efremenko, Yu; Ejiri, H.; Elliott, S. R.; Gilliss, T.; Giovanetti, G. K.; Green, M.; Gruszko, J.; Guinn, I. S.; Guiseppe, V. E.; Haufe, C. R.; Hehn, L.; Henning, R.; Hoppe, E. W.; Howe, M. A.; Keeter, K. J.; Kidd, M. F.; Konovalov, S. I.; Kouzes, R. T.; Lopez, A. M.; Martin, R. D.; Massarczyk, R.; Meijer, S. J.; Mertens, S.; Myslik, J.; Othman, G.; Pettus, W.; Poon, A. W. P.; Radford, D. C.; Rager, J.; Reine, A. L.; Rielage, K.; Ruof, N. W.; Shanks, B.; Shirchenko, M.; Suriano, A. M.; Tedeschi, D.; Varner, R. L.; Vasilyev, S.; Vetter, K.; Vorren, K.; White, B. R.; Wilkerson, J. F.; Wiseman, C.; Xu, W.; Yakushev, E.; Yumatov, V.; Zhitnikov, I.; Zhu, B. Z.

2018-05-01

The MAJORANA Collaboration is using an array of high-purity Ge detectors to search for neutrinoless double-beta decay in 76Ge. Searches for neutrinoless double-beta decay are understood to be the only viable experimental method for testing the Majorana nature of the neutrino. Observation of this decay would imply violation of lepton number, that neutrinos are Majorana in nature, and provide information on the neutrino mass. The MAJORANA DEMONSTRATOR comprises 44.1 kg of p-type point-contact Ge detectors (29.7 kg enriched in 76Ge) surrounded by a low-background shield system. The experiment achieved a high efficiency of converting raw Ge material to detectors and an unprecedented detector energy resolution of 2.5 keV FWHM at Qββ. The MAJORANA collaboration began taking physics data in 2016. This paper summarizes key construction aspects of the Demonstrator and shows preliminary results from initial data.

The Majorana Demonstrator Status and Preliminary Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, C. -H.; Alvis, S. I.; Arnquist, I. J.

The MAJORANA Collaboration is using an array of high-purity Ge detectors to search for neutrinoless double-beta decay in 76Ge. Searches for neutrinoless double-beta decay are understood to be the only viable experimental method for testing the Majorana nature of the neutrino. Observation of this decay would imply violation of lepton number, that neutrinos are Majorana in nature, and provide information on the neutrino mass. The MAJORANA DEMONSTRATOR comprises 44.1 kg of p-type point-contact Ge detectors (29.7 kg enriched in 76Ge) surrounded by a low-background shield system. The experiment achieved a high efficiency of converting raw Ge material to detectors andmore » an unprecedented detector energy resolution of 2.5 keV FWHM at Q ββ. The MAJORANA collaboration began taking physics data in 2016. Here, this paper summarizes key construction aspects of the Demonstrator and shows preliminary results from initial data.« less

Preliminary Design of a Digital Holography PFC Erosion Diagnostic for MPEX

NASA Astrophysics Data System (ADS)

Thomas, C. E. (Tommy), Jr.; Biewer, T. M.; Shaw, G. C.; Baylor, L. R.; Combs, S. K.; Meitner, S. J.; Rapp, J.; Hillis, D. L.; Granstedt, E. M.; Majeski, R.; Kaita, R.

2015-11-01

Preliminary design of a Digital Holography (DH) in-situ Plasma Facing Component (PFC) erosion diagnostic to be used on the proto-MPEX/MPEX experiment is presented. Design trade-offs are discussed including the selection of CO2 laser frequencies and whether/where to use reflective or refractive optical components. The costs and benefits of using a high-speed (expensive) infrared (IR) camera or a lower speed (inexpensive) IR camera, and whether to use simultaneous or sequential acquisition of DH exposures for the dual wavelength system are also described. Expected layout, resolution, and noise figures will be discussed, along with resolution and noise data from previous work at ORNL and PPPL. Partial Support from USDOE Contract DE-AC02-09CH11466 and USDOE Grant DE-FG02-07ER84724 for previous Digital Holography work done at ORNL and PPPL is gratefully acknowledged.

[Comprehensive testing system for cardiorespiratory interaction research].

PubMed

Zhang, Zhengbo; Wang, Buqing; Wang, Weidong; Zheng, Jiewen; Liu, Hongyun; Li, Kaiyuan; Sun, Congcong; Wang, Guojing

2013-04-01

To investigate the modulation effects of breathing movement on cardiovascular system and to study the physiological coupling relationship between respiration and cardiovascular system, we designed a comprehensive testing system for cardiorespiratory interaction research. This system, comprising three parts, i. e. physiological signal conditioning unit, data acquisition and USB medical isolation unit, and a PC based program, can acquire multiple physiological data such as respiratory flow, rib cage and abdomen movement, electrocardiograph, artery pulse wave, cardiac sounds, skin temperature, and electromyography simultaneously under certain experimental protocols. Furthermore this system can be used in research on short-term cardiovascular variability by paced breathing. Preliminary experiments showed that this system could accurately record rib cage and abdomen movement under very low breathing rate, using respiratory inductive plethysmography to acquire respiration signal in direct-current coupling mode. After calibration, this system can be used to estimate ventilation non-intrusively and correctly. The PC based program can generate audio and visual biofeedback signal, and guide the volunteers to perform a slow and regular breathing. An experiment on healthy volunteers showed that this system was able to guide the volunteers to do slow breathing effectively and simultaneously record multiple physiological data during the experiments. Signal processing techniques were used for off-line data analysis, such as non-invasive ventilation calibration, QRS complex wave detection, and respiratory sinus arrhythmia and pulse wave transit time calculation. The experiment result showed that the modulation effect on RR interval, respiratory sinus arrhythmia (RSA), pulse wave transit time (PWTT) by respiration would get stronger with the going of the slow and regular breathing.

The NASA Juncture Flow Experiment: Goals, Progress, and Preliminary Testing (Invited)

NASA Technical Reports Server (NTRS)

Rumsey, Christopher L.; Neuhart, Danny H.; Kegerise, Michael A.

2016-01-01

NASA has been working toward designing and conducting a juncture flow experiment on a wing-body aircraft configuration. The experiment is planned to provide validation-quality data for CFD that focuses on the onset and progression of a separation bubble near the wing-body juncture trailing edge region. This paper describes the goals and purpose of the experiment. Although currently considered unreliable, preliminary CFD analyses of several different configurations are shown. These configurations have been subsequently tested in a series of "risk-reduction" wind tunnel tests, in order to help down-select to a final configuration that will attain the desired flow behavior. The risk-reduction testing at the higher Reynolds number has not yet been completed (at the time of this writing), but some results from one of the low-Reynolds-number experiments are shown.

The meta-Gaussian Bayesian Processor of forecasts and associated preliminary experiments

NASA Astrophysics Data System (ADS)

Chen, Fajing; Jiao, Meiyan; Chen, Jing

2013-04-01

Public weather services are trending toward providing users with probabilistic weather forecasts, in place of traditional deterministic forecasts. Probabilistic forecasting techniques are continually being improved to optimize available forecasting information. The Bayesian Processor of Forecast (BPF), a new statistical method for probabilistic forecast, can transform a deterministic forecast into a probabilistic forecast according to the historical statistical relationship between observations and forecasts generated by that forecasting system. This technique accounts for the typical forecasting performance of a deterministic forecasting system in quantifying the forecast uncertainty. The meta-Gaussian likelihood model is suitable for a variety of stochastic dependence structures with monotone likelihood ratios. The meta-Gaussian BPF adopting this kind of likelihood model can therefore be applied across many fields, including meteorology and hydrology. The Bayes theorem with two continuous random variables and the normal-linear BPF are briefly introduced. The meta-Gaussian BPF for a continuous predictand using a single predictor is then presented and discussed. The performance of the meta-Gaussian BPF is tested in a preliminary experiment. Control forecasts of daily surface temperature at 0000 UTC at Changsha and Wuhan stations are used as the deterministic forecast data. These control forecasts are taken from ensemble predictions with a 96-h lead time generated by the National Meteorological Center of the China Meteorological Administration, the European Centre for Medium-Range Weather Forecasts, and the US National Centers for Environmental Prediction during January 2008. The results of the experiment show that the meta-Gaussian BPF can transform a deterministic control forecast of surface temperature from any one of the three ensemble predictions into a useful probabilistic forecast of surface temperature. These probabilistic forecasts quantify the uncertainty of the control forecast; accordingly, the performance of the probabilistic forecasts differs based on the source of the underlying deterministic control forecasts.

Prognostics of Power Electronics, Methods and Validation Experiments

NASA Technical Reports Server (NTRS)

Kulkarni, Chetan S.; Celaya, Jose R.; Biswas, Gautam; Goebel, Kai

2012-01-01

Abstract Failure of electronic devices is a concern for future electric aircrafts that will see an increase of electronics to drive and control safety-critical equipment throughout the aircraft. As a result, investigation of precursors to failure in electronics and prediction of remaining life of electronic components is of key importance. DC-DC power converters are power electronics systems employed typically as sourcing elements for avionics equipment. Current research efforts in prognostics for these power systems focuses on the identification of failure mechanisms and the development of accelerated aging methodologies and systems to accelerate the aging process of test devices, while continuously measuring key electrical and thermal parameters. Preliminary model-based prognostics algorithms have been developed making use of empirical degradation models and physics-inspired degradation model with focus on key components like electrolytic capacitors and power MOSFETs (metal-oxide-semiconductor-field-effect-transistor). This paper presents current results on the development of validation methods for prognostics algorithms of power electrolytic capacitors. Particularly, in the use of accelerated aging systems for algorithm validation. Validation of prognostics algorithms present difficulties in practice due to the lack of run-to-failure experiments in deployed systems. By using accelerated experiments, we circumvent this problem in order to define initial validation activities.

A system level model for preliminary design of a space propulsion solid rocket motor

NASA Astrophysics Data System (ADS)

Schumacher, Daniel M.

Preliminary design of space propulsion solid rocket motors entails a combination of components and subsystems. Expert design tools exist to find near optimal performance of subsystems and components. Conversely, there is no system level preliminary design process for space propulsion solid rocket motors that is capable of synthesizing customer requirements into a high utility design for the customer. The preliminary design process for space propulsion solid rocket motors typically builds on existing designs and pursues feasible rather than the most favorable design. Classical optimization is an extremely challenging method when dealing with the complex behavior of an integrated system. The complexity and combinations of system configurations make the number of the design parameters that are traded off unreasonable when manual techniques are used. Existing multi-disciplinary optimization approaches generally address estimating ratios and correlations rather than utilizing mathematical models. The developed system level model utilizes the Genetic Algorithm to perform the necessary population searches to efficiently replace the human iterations required during a typical solid rocket motor preliminary design. This research augments, automates, and increases the fidelity of the existing preliminary design process for space propulsion solid rocket motors. The system level aspect of this preliminary design process, and the ability to synthesize space propulsion solid rocket motor requirements into a near optimal design, is achievable. The process of developing the motor performance estimate and the system level model of a space propulsion solid rocket motor is described in detail. The results of this research indicate that the model is valid for use and able to manage a very large number of variable inputs and constraints towards the pursuit of the best possible design.

[Analysis on origin and evolution of mumps].

PubMed

Zhao, Yan

2004-10-01

There was a preliminary recognition on mumps during the Qin-Han to Sui-Tang dynasty, laying a foundation for the scholastic development on this topic in later generations. The title of this disease was identified in Song-Jin-Yuan dynasty with gradual deepening on its principle-method-formula-medication system, a great progress of recognition as compared with the previous ages. In the Ming-Qing dynasty, the recognition became even more systematic, with certain breakthrough in the system of principle-method-formula-medication. In modern age, the experiences were inherited and developed to integrate to modern biomedicine, so that the theory and clinical practice become even more perfect.

Practical in-situ determination of ortho-para hydrogen ratios via fiber-optic based Raman spectroscopy

DOE PAGES

Sutherland, Liese -Marie; Knudson, James N.; Mocko, Michal; ...

2015-12-17

An experiment was designed and developed to prototype a fiber-optic-based laser system, which measures the ratio of ortho-hydrogen to para-hydrogen in an operating neutron moderator system at the Los Alamos Neutron Science Center (LANSCE) spallation neutron source. Preliminary measurements resulted in an ortho to para ratio of 3.06:1, which is within acceptable agreement with the previously published ratio. As a result, the successful demonstration of Raman Spectroscopy for this measurement is expected to lead to a practical method that can be applied for similar in-situ measurements at operating neutron spallation sources.

Practical in-situ determination of ortho-para hydrogen ratios via fiber-optic based Raman spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sutherland, Liese -Marie; Knudson, James N.; Mocko, Michal

An experiment was designed and developed to prototype a fiber-optic-based laser system, which measures the ratio of ortho-hydrogen to para-hydrogen in an operating neutron moderator system at the Los Alamos Neutron Science Center (LANSCE) spallation neutron source. Preliminary measurements resulted in an ortho to para ratio of 3.06:1, which is within acceptable agreement with the previously published ratio. As a result, the successful demonstration of Raman Spectroscopy for this measurement is expected to lead to a practical method that can be applied for similar in-situ measurements at operating neutron spallation sources.

Development of a fully automated network system for long-term health-care monitoring at home.

PubMed

Motoi, K; Kubota, S; Ikarashi, A; Nogawa, M; Tanaka, S; Nemoto, T; Yamakoshi, K

2007-01-01

Daily monitoring of health condition at home is very important not only as an effective scheme for early diagnosis and treatment of cardiovascular and other diseases, but also for prevention and control of such diseases. From this point of view, we have developed a prototype room for fully automated monitoring of various vital signs. From the results of preliminary experiments using this room, it was confirmed that (1) ECG and respiration during bathing, (2) excretion weight and blood pressure, and (3) respiration and cardiac beat during sleep could be monitored with reasonable accuracy by the sensor system installed in bathtub, toilet and bed, respectively.

Preliminary science report on the directional solidification of hypereutectic cast iron during KC-135 low-G maneuvers

NASA Technical Reports Server (NTRS)

Curreri, P. A.; Stefanescu, D. M.; Hendrix, J. C.

1983-01-01

An ADSS-P directional solidification furnace was reconfigured for operation on the KC-135 low-g aircraft. The system offers many advantages over quench ingot methods for study of the effects of sedimentation and convection on alloy formation. The directional sodification furnace system was first flown during the September 1982 series of flights. The microstructure of the hypereutectic cast iron sample solidified on one of these flights suggests a low-g effect on graphite morphology. Further experiments are needed to ascertain that this effect is due to low-gravity and to deduce which of the possible mechanisms is responsible for it.

Magnetic Field Observations near Mercury: Preliminary Results from Mariner 10.

PubMed

Ness, N F; Behannon, K W; Lepping, R P; Whang, Y C; Schatten, K H

1974-07-12

Results are presented from a preliminary analysis of data obtained near Mercury on 29 March 1974 by the NASA-GSFC magnetic field experiment on Mariner 10. Rather unexpectedly, a very well-developed, detached bow shock wave, which develops as the super-Alfvénic solar wind interacts with the planet, has been observed. In addition, a magnetosphere-like region, with maximum field strength of 98 gammas at closest approach (704 kilometers altitude), has been observed, contained within boundaries similar to the terrestrial magnetopause. The obstacle deflecting the solar wind flow is global in size, but the origin of the enhanced magnetic field has not yet been uniquely established. The field may be intrinsic to the planet and distorted by interaction with the solar wind. It may also be associated with a complex induction process whereby the planetary interior-atmosphere-ionosphere interacts with the solar wind flow to generate the observed field by a dynamo action. The complete body of data favors the preliminary conclusion that Mercury has an intrinsic magnetic field. If this is correct, it represents a major scientific discovery in planetary magnetism and will have considerable impact on studies of the origin of the solar system.

Energy Efficient Engine: Control system preliminary definition report

NASA Technical Reports Server (NTRS)

Howe, David C.

1986-01-01

The object of the Control Preliminary Definition Program was to define a preliminary control system concept as a part of the Energy Efficient Engine program. The program was limited to a conceptual definition of a full authority digital electronic control system. System requirements were determined and a control system was conceptually defined to these requirements. Areas requiring technological development were identified and a plan was established for implementing the identified technological features, including a control technology demonstration. A significant element of this program was a study of the potential benefits of closed-loop active clearance control, along with laboratory tests of candidate clearance sensor elements for a closed loop system.

Low-temperature catalytic gasification of food processing wastes. 1995 topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, D.C.; Hart, T.R.

The catalytic gasification system described in this report has undergone continuing development and refining work at Pacific Northwest National Laboratory (PNNL) for over 16 years. The original experiments, performed for the Gas Research Institute, were aimed at developing kinetics information for steam gasification of biomass in the presence of catalysts. From the fundamental research evolved the concept of a pressurized, catalytic gasification system for converting wet biomass feedstocks to fuel gas. Extensive batch reactor testing and limited continuous stirred-tank reactor tests provided useful design information for evaluating the preliminary economics of the process. This report is a follow-on to previousmore » interim reports which reviewed the results of the studies conducted with batch and continuous-feed reactor systems from 1989 to 1994, including much work with food processing wastes. The discussion here provides details of experiments on food processing waste feedstock materials, exclusively, that were conducted in batch and continuous- flow reactors.« less

Review of operational aspects of initial experiments utilizing the U.S. MLS. [microwave landing system effectiveness

NASA Technical Reports Server (NTRS)

Walsh, T. M.; Morello, S. A.; Reeder, J. P.

1976-01-01

An exercise to support the Federal Aviation Administration in demonstrating the U.S. candidate for an international microwave landing system (MLS) was conducted by NASA. During this demonstration the MLS was utilized to provide the TCV Boeing 737 research airplane with guidance for automatic control during transition from conventional RNAV to MLS RNAV in curved, descending flight; flare; touchdown; and roll-out. Flight profiles, system configuration, displays, and operating procedures used in the demonstration are described, and preliminary results of flight data analysis are discussed. Recent experiences with manually controlled flight in the NAFEC MLS environment are also discussed. The demonstration shows that in automatic three-dimensional flight, the volumetric signal coverage of the MLS can be exploited to enable a commercial carrier class airplane to perform complex curved, descending paths with precision turns into short final approaches terminating in landing and roll-out, even when subjected to strong and gusty tail and cross wind components and severe wind shear.

Achieving ethanol-type fermentation for hydrogen production in a granular sludge system by aeration.

PubMed

Zhang, Song; Liu, Min; Chen, Ying; Pan, Yu-Ting

2017-01-01

To investigate the effects of aeration on hydrogen-producing granular system, experiments were performed in two laboratory-scale anaerobic internal circulation hydrogen production (AICHP) reactors. The preliminary experiment of Reactor 1 showed that direct aeration was beneficial to enhancing hydrogen production. After the direct aeration was implied in Reactor 2, hydrogen production rate (HPR) and hydrogen content were increased by 100% and 60%, respectively. In addition, mixed-acid fermentation was transformed into typical ethanol-type fermentation (ETF). Illumina MiSeq sequencing shows that the direct aeration did not change the species of hydrogen-producing bacteria but altered their abundance. Hydrogen-producing bacteria and ethanol-type fermentative bacteria were increased by 24.5% and 146.3%, respectively. Ethanoligenens sp. sharply increased by 162.2% and turned into predominant bacteria in the system. These findings indicated that appropriate direct aeration might be a novel and promising way to obtain ETF and enhance hydrogen production in practical use. Copyright © 2016 Elsevier Ltd. All rights reserved.

Automated Sample Exchange Robots for the Structural Biology Beam Lines at the Photon Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hiraki, Masahiko; Watanabe, Shokei; Yamada, Yusuke

2007-01-19

We are now developing automated sample exchange robots for high-throughput protein crystallographic experiments for onsite use at synchrotron beam lines. It is part of the fully automated robotics systems being developed at the Photon Factory, for the purposes of protein crystallization, monitoring crystal growth, harvesting and freezing crystals, mounting the crystals inside a hutch and for data collection. We have already installed the sample exchange robots based on the SSRL automated mounting system at our insertion device beam lines BL-5A and AR-NW12A at the Photon Factory. In order to reduce the time required for sample exchange further, a prototype ofmore » a double-tonged system was developed. As a result of preliminary experiments with double-tonged robots, the sample exchange time was successfully reduced from 70 seconds to 10 seconds with the exception of the time required for pre-cooling and warming up the tongs.« less

Chemical vapor deposition growth

NASA Technical Reports Server (NTRS)

Ruth, R. P.; Manasevit, H. M.; Kenty, J. L.; Moudy, L. A.; Simpson, W. I.; Yang, J. J.

1976-01-01

A chemical vapor deposition (CVD) reactor system with a vertical deposition chamber was used for the growth of Si films on glass, glass-ceramic, and polycrystalline ceramic substrates. Silicon vapor was produced by pyrolysis of SiH4 in a H2 or He carrier gas. Preliminary deposition experiments with two of the available glasses were not encouraging. Moderately encouraging results, however, were obtained with fired polycrystalline alumina substrates, which were used for Si deposition at temperatures above 1,000 C. The surfaces of both the substrates and the films were characterized by X-ray diffraction, reflection electron diffraction, scanning electron microscopy optical microscopy, and surface profilometric techniques. Several experiments were conducted to establish baseline performance data for the reactor system, including temperature distributions on the sample pedestal, effects of carrier gas flow rate on temperature and film thickness, and Si film growth rate as a function of temperature.

PROBING THE DARK AGES AT z ∼ 20: THE SCI-HI 21 cm ALL-SKY SPECTRUM EXPERIMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Voytek, Tabitha C.; Natarajan, Aravind; Peterson, Jeffrey B.

2014-02-10

We present first results from the SCI-HI experiment, which we used to measure the all-sky-averaged 21 cm brightness temperature in the redshift range 14.8 < z < 22.7. The instrument consists of a single broadband sub-wavelength size antenna and a sampling system for real-time data processing and recording. Preliminary observations were completed in 2013 June at Isla Guadalupe, a Mexican biosphere reserve located in the Pacific Ocean. The data was cleaned to excise channels contaminated by radio frequency interference, and the system response was calibrated by comparing the measured brightness temperature to the Global Sky Model of the Galaxy and bymore » independent measurement of Johnson noise from a calibration terminator. We present our results, discuss the cosmological implications, and describe plans for future work.« less

Initial utility experience with cluster of three Mod-2 wind turbine systems

NASA Technical Reports Server (NTRS)

Seely, D. B.; Warchol, E. J.; Butler, N. G.; Ciranny, S.

1982-01-01

This paper describes the initial utility experiences of operating three MOD-2s during the Engineering Acceptance Testing. Electrical quantities of bus voltage, phase currents and power are initially being recorded to evaluate impacts to customers on the 69-kV subtransmission line during synchronization and operation of one or more WTSs. To date, effects on the system have been essentially undetectable. Measurements of television signal strengths were taken at an existing television remote pickup and relay station at the WTS site. Potential TV signal interference problems from the WTSs have been avoided by replacing the remote pickups with microwave repeater links for the four TV channels received from Portland, Oregon. Preliminary measurements of audible and sub-audible noise levels indicate that the upwind rotor, tubular tower design of the MOD-2 does not have the pulsing high intensity infrasound problems experienced by the MOD-1 machine at Boone, North Carolina.

Mass Transport Phenomena Between Bubbles and Dissolved Gases in Liquids Under Reduced Gravity Conditions

NASA Technical Reports Server (NTRS)

Dewitt, K. J.; Brockwell, J. L.

1985-01-01

The long term objective of the experiment is to observe the dissolution of isolated, immobile gas bubbles of specified size and composition in a solvent liquid of known concentration in the reduced gravity environment of earth orbit. Preliminary bubble dissolution experiment conducted both in the NASA Lewis 2.2 sec drop tower and in normal gravity using SO2 - Toluene system were not completely successful in their objective. The method of gas injection and lack of bubble interface stabiliy experienced due to the extreme solubility of SO in Toluene has the effects of changing the problem from that of bubble dissolution to one of bubble formation stability and subsequent dissolution in a liquid of unknown initial solute concentration. Current work involves further experimentation in order to refine the bubble injection system and to investigate the concept of having a bubble with a critical radius in a state of unstable equilibrium.

Experiences with a Barista Robot, FusionBot

NASA Astrophysics Data System (ADS)

Limbu, Dilip Kumar; Tan, Yeow Kee; Wong, Chern Yuen; Jiang, Ridong; Wu, Hengxin; Li, Liyuan; Kah, Eng Hoe; Yu, Xinguo; Li, Dong; Li, Haizhou

In this paper, we describe the implemented service robot, called FusionBot. The goal of this research is to explore and demonstrate the utility of an interactive service robot in a smart home environment, thereby improving the quality of human life. The robot has four main features: 1) speech recognition, 2) object recognition, 3) object grabbing and fetching and 4) communication with a smart coffee machine. Its software architecture employs a multimodal dialogue system that integrates different components, including spoken dialog system, vision understanding, navigation and smart device gateway. In the experiments conducted during the TechFest 2008 event, the FusionBot successfully demonstrated that it could autonomously serve coffee to visitors on their request. Preliminary survey results indicate that the robot has potential to not only aid in the general robotics but also contribute towards the long term goal of intelligent service robotics in smart home environment.

Shader Lamps Virtual Patients: the physical manifestation of virtual patients.

PubMed

Rivera-Gutierrez, Diego; Welch, Greg; Lincoln, Peter; Whitton, Mary; Cendan, Juan; Chesnutt, David A; Fuchs, Henry; Lok, Benjamin

2012-01-01

We introduce the notion of Shader Lamps Virtual Patients (SLVP) - the combination of projector-based Shader Lamps Avatars and interactive virtual humans. This paradigm uses Shader Lamps Avatars technology to give a 3D physical presence to conversational virtual humans, improving their social interactivity and enabling them to share the physical space with the user. The paradigm scales naturally to multiple viewers, allowing for scenarios where an instructor and multiple students are involved in the training. We have developed a physical-virtual patient for medical students to conduct ophthalmic exams, in an interactive training experience. In this experience, the trainee practices multiple skills simultaneously, including using a surrogate optical instrument in front of a physical head, conversing with the patient about his fears, observing realistic head motion, and practicing patient safety. Here we present a prototype system and results from a preliminary formative evaluation of the system.

Study of mouse behavioural response in microgravity: ethogram and neurobiological related

NASA Astrophysics Data System (ADS)

Santucci, Daniela; Francia, Nadia; Schwartz, Silvia; Biticchi, Roberta; Liu, Yi; Cancedda, Ranieri; Aloe, Luigi

The conquest of space, which started with the dog Laika in 1966 to be followed few years later by Yuri Gagarin, has witnessed an increasing numbers of both vertebrates (tadpoles, frogs, rats mice etc.) and invertebrates (flies, scorpions, protozoa) species exposed to zero gravity levels. Animals are sent into orbit to proactively foresee possible health problems in humans. The issue of animal exposure to un-physiological gravity is of primary importance to i) understand behavioural and physiological adaptations in such environment as well as ii) develop coun-termeasures to improve 0-g life conditions and reduce possible animal suffering. The Mouse Drawer System (MDS), an Italian facility, has been transferred to the International Space Sta-tion with a first experiment investigating mechanisms underlying bone mass loss in microgravity in mice. Preliminary and ground-based control experiments have been conducted with six mice housed individually inside the MDS facility for 20 and 100 days. The behavioural repertoire of wild-type and transgenic mice housed in the MDS has been videorecorded with the observation subsystem, which allows to monitor animal's behavior through the use of 6 video cameras. The behavioural patterns characterizing mice in the MDS system have been finely analysed at several time points during the the experiment. Moreover, neurobiological parameters, known to be involved in the response to stress, have been evaluated. In particular, NGF and BDNF levels have been measured in the central nervous system (hippocampus, striatum, and cortex), adrenal gland and limbs. Preliminary data from ground based experiment revealed Several dif-ferences in behavioural profile between wt and tg mice, with transgenic ones apparently more active than wild type controls. Moreover a clear difference in time spent in different areas of the MDS cage was observed. Finally changes in neurotrophins levels were observed in relation to both genotype and environmental conditions. Data so far collected will be used as baseline and will compared with those obtained during spaceflight exposure currently under analysis and a fine characterization of the behavioral repertoire (ethogram) of the mice exposed to space environment will be reported.

ECR plasma thruster research - Preliminary theory and experiments

NASA Technical Reports Server (NTRS)

Sercel, Joel C.; Fitzgerald, Dennis J.

1989-01-01

A preliminary theory of the operation of the electron-cyclotron-resonance (ECR) plasma thruster is described along with an outline of recent experiments. This work is presented to communicate the status of an ongoing research effort directed at developing a unified theory to quantitatively describe the operation of the ECR plasma thruster. The theory is presented as a set of nonlinear ordinary differential equations and boundary conditions which describe the plasma density, velocity, and electron temperature. Diagnostic tools developed to measure plasma conditions in the existing research device are described.

New advances in the partial-reflection-drifts experiment using microprocessors

NASA Technical Reports Server (NTRS)

Ruggerio, R. L.; Bowhill, S. A.

1982-01-01

Improvements to the partial reflection drifts experiment are completed. The results of the improvements include real time processing and simultaneous measurements of the D region with coherent scatter. Preliminary results indicate a positive correlation between drift velocities calculated by both methods during a two day interval. The possibility now exists for extended observations between partial reflection and coherent scatter. In addition, preliminary measurements could be performed between partial reflection and meteor radar to complete a comparison of methods used to determine velocities in the D region.

Robotic Single-Site Surgery for Female-to-Male Transsexuals: Preliminary Experience

PubMed Central

Bogliolo, Stefano; Cassani, Chiara; Babilonti, Luciana; Gardella, Barbara; Zanellini, Francesca; Santamaria, Valentina; Nappi, Rossella Elena; Spinillo, Arsenio

2014-01-01

Hysterectomy with bilateral salpingo-oophorectomy is a part of gender reassignment surgery for the treatment of female-to-male transsexualism. Over the last years many efforts were made in order to reduce invasiveness of laparoscopic and robotic surgery such as the introduction of single-site approach. We report our preliminary experience on single-site robotic hysterectomy for cross-sex reassignment surgery. Our data suggest that single-site robotic hysterectomy is feasible and safe in female-to-male transsexualism with some benefits in terms of postoperative pain and aesthetic results. PMID:24982976

Accessing defect dynamics using intense, nanosecond pulsed ion beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Persaud, A.; Barnard, J. J.; Guo, H.

2015-06-18

Gaining in-situ access to relaxation dynamics of radiation induced defects will lead to a better understanding of materials and is important for the verification of theoretical models and simulations. We show preliminary results from experiments at the new Neutralized Drift Compression Experiment (NDCX-II) at Lawrence Berkeley National Laboratory that will enable in-situ access to defect dynamics through pump-probe experiments. Here, the unique capabilities of the NDCX-II accelerator to generate intense, nanosecond pulsed ion beams are utilized. Preliminary data of channeling experiments using lithium and potassium ions and silicon membranes are shown. We compare these data to simulation results using Crystalmore » Trim. Furthermore, we discuss the improvements to the accelerator to higher performance levels and the new diagnostics tools that are being incorporated.« less

Development of a verification program for deployable truss advanced technology

NASA Technical Reports Server (NTRS)

Dyer, Jack E.

1988-01-01

Use of large deployable space structures to satisfy the growth demands of space systems is contingent upon reducing the associated risks that pervade many related technical disciplines. The overall objectives of this program was to develop a detailed plan to verify deployable truss advanced technology applicable to future large space structures and to develop a preliminary design of a deployable truss reflector/beam structure for use a a technology demonstration test article. The planning is based on a Shuttle flight experiment program using deployable 5 and 15 meter aperture tetrahedral truss reflections and a 20 m long deployable truss beam structure. The plan addresses validation of analytical methods, the degree to which ground testing adequately simulates flight and in-space testing requirements for large precision antenna designs. Based on an assessment of future NASA and DOD space system requirements, the program was developed to verify four critical technology areas: deployment, shape accuracy and control, pointing and alignment, and articulation and maneuvers. The flight experiment technology verification objectives can be met using two shuttle flights with the total experiment integrated on a single Shuttle Test Experiment Platform (STEP) and a Mission Peculiar Experiment Support Structure (MPESS). First flight of the experiment can be achieved 60 months after go-ahead with a total program duration of 90 months.

40 CFR 161.170 - Preliminary analysis.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Preliminary analysis. (a) If the product is produced by an integrated system, the applicant must provide a preliminary analysis of each technical grade of active ingredient contained in the product to identify all... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Preliminary analysis. 161.170 Section...

Insights from Modeling the Integrated Climate, Biogeochemical Cycles, Human Activities and Their Interactions in the ACME Earth System Model

NASA Astrophysics Data System (ADS)

Leung, L. R.; Thornton, P. E.; Riley, W. J.; Calvin, K. V.

2017-12-01

Towards the goal of understanding the contributions from natural and managed systems to current and future greenhouse gas fluxes and carbon-climate and carbon-CO2 feedbacks, efforts have been underway to improve representations of the terrestrial, river, and human components of the ACME earth system model. Broadly, our efforts include implementation and comparison of approaches to represent the nutrient cycles and nutrient limitations on ecosystem production, extending the river transport model to represent sediment and riverine biogeochemistry, and coupling of human systems such as irrigation, reservoir operations, and energy and land use with the ACME land and river components. Numerical experiments have been designed to understand how terrestrial carbon, nitrogen, and phosphorus cycles regulate climate system feedbacks and the sensitivity of the feedbacks to different model treatments, examine key processes governing sediment and biogeochemistry in the rivers and their role in the carbon cycle, and exploring the impacts of human systems in perturbing the hydrological and carbon cycles and their interactions. This presentation will briefly introduce the ACME modeling approaches and discuss preliminary results and insights from numerical experiments that lay the foundation for improving understanding of the integrated climate-biogeochemistry-human system.

Human Reliability Assessments: Using the Past (Shuttle) to Predict the Future (Orion)

NASA Technical Reports Server (NTRS)

DeMott, Diana L.; Bigler, Mark A.

2017-01-01

NASA (National Aeronautics and Space Administration) Johnson Space Center (JSC) Safety and Mission Assurance (S&MA) uses two human reliability analysis (HRA) methodologies. The first is a simplified method which is based on how much time is available to complete the action, with consideration included for environmental and personal factors that could influence the human's reliability. This method is expected to provide a conservative value or placeholder as a preliminary estimate. This preliminary estimate or screening value is used to determine which placeholder needs a more detailed assessment. The second methodology is used to develop a more detailed human reliability assessment on the performance of critical human actions. This assessment needs to consider more than the time available, this would include factors such as: the importance of the action, the context, environmental factors, potential human stresses, previous experience, training, physical design interfaces, available procedures/checklists and internal human stresses. The more detailed assessment is expected to be more realistic than that based primarily on time available. When performing an HRA on a system or process that has an operational history, we have information specific to the task based on this history and experience. In the case of a Probabilistic Risk Assessment (PRA) that is based on a new design and has no operational history, providing a "reasonable" assessment of potential crew actions becomes more challenging. To determine what is expected of future operational parameters, the experience from individuals who had relevant experience and were familiar with the system and process previously implemented by NASA was used to provide the "best" available data. Personnel from Flight Operations, Flight Directors, Launch Test Directors, Control Room Console Operators, and Astronauts were all interviewed to provide a comprehensive picture of previous NASA operations. Verification of the assumptions and expectations expressed in the assessments will be needed when the procedures, flight rules, and operational requirements are developed and then finalized.

Human Reliability Assessments: Using the Past (Shuttle) to Predict the Future (Orion)

NASA Technical Reports Server (NTRS)

DeMott, Diana; Bigler, Mark

2016-01-01

NASA (National Aeronautics and Space Administration) Johnson Space Center (JSC) Safety and Mission Assurance (S&MA) uses two human reliability analysis (HRA) methodologies. The first is a simplified method which is based on how much time is available to complete the action, with consideration included for environmental and personal factors that could influence the human's reliability. This method is expected to provide a conservative value or placeholder as a preliminary estimate. This preliminary estimate or screening value is used to determine which placeholder needs a more detailed assessment. The second methodology is used to develop a more detailed human reliability assessment on the performance of critical human actions. This assessment needs to consider more than the time available, this would include factors such as: the importance of the action, the context, environmental factors, potential human stresses, previous experience, training, physical design interfaces, available procedures/checklists and internal human stresses. The more detailed assessment is expected to be more realistic than that based primarily on time available. When performing an HRA on a system or process that has an operational history, we have information specific to the task based on this history and experience. In the case of a Probabilistic Risk Assessment (PRA) that is based on a new design and has no operational history, providing a "reasonable" assessment of potential crew actions becomes more challenging. In order to determine what is expected of future operational parameters, the experience from individuals who had relevant experience and were familiar with the system and process previously implemented by NASA was used to provide the "best" available data. Personnel from Flight Operations, Flight Directors, Launch Test Directors, Control Room Console Operators and Astronauts were all interviewed to provide a comprehensive picture of previous NASA operations. Verification of the assumptions and expectations expressed in the assessments will be needed when the procedures, flight rules and operational requirements are developed and then finalized.

Preliminary design package for solar heating and hot water system

NASA Technical Reports Server (NTRS)

1977-01-01

The preliminary design review on the development of a multi-family solar heating and domestic hot water prototype system is presented. The report contains the necessary information to evaluate the system. The system consists of the following subsystems: collector, storage, transport, control and Government-furnished site data acquisition.

Indocyanine green-enhanced fluorescence in laparoscopic sleeve gastrectomy.

PubMed

Frattini, Francesco; Lavazza, Matteo; Mangano, Alberto; Amico, Francesco; Rausei, Stefano; Rovera, Francesca; Boni, Luigi; Dionigi, Gianlorenzo

2015-05-01

The aim of this study is to present our preliminary experience with indocyanine green fluorescence (IGF) imaging in laparoscopic sleeve gastrectomy. After dissection of the greater curve sleeve, gastrectomy is performed using a linear articulated stapler. Once the stomach is resected, an indocyanine green solution is prepared and injected in a periferic vein. A laparoscopic system with a high-definition camera system connected to a laparoscope equipped with a specific filter for optimal detection of the near-infrared fluorescence was used at all times as previously reported in a paper of Boni et al. A methylene blue test is routinely performed after near-infrared fluorescence, and a routine gastrografin upper gastrointestinal study is performed on postoperative day 2. We retrospectively identified 15 patients undergoing laparoscopic sleeve gastrectomy between April and October 2014. IGF imaging was used for all patients. A regular and homogeneous perfusion was observed along the entire gastric sleeve including the esophago-gastric junction. On the contrary, the excised specimen appeared devascularized at IGF imaging as expected. Intraoperative methylene blue test was negative in all cases. The contrast swallow did not document any leak. Neither clinical leak nor other complications occurred postoperatively (minimum follow-up of 2 months). IGF is a recent development in minimally invasive surgery. In this preliminary experience, IGF results resemble to intraoperative methylene blue test and postoperative contrast swallow ones. IGF allows a real-time assessment and gives a direct image of tissue perfusion and vascularization. Moreover, IGF may be helpful to explain the exact pathogenesis of gastric leak.

A CCD Spectrometer for One Dollar

NASA Astrophysics Data System (ADS)

Beaver, J.; Robert, D.

2011-09-01

We describe preliminary tests on a very low-cost system for obtaining stellar spectra for instructional use in an introductory astronomy laboratory. CCD imaging with small telescopes is now commonplace and relatively inexpensive. Giving students direct experience taking stellar spectra, however, is much more difficult, and the equipment can easily be out of reach for smaller institutions, especially if one wants to give the experience to large numbers of students. We have performed preliminary tests on an extremely low-cost (about $1.00) objective grating that can be coupled with an existing CCD camera or commercial digital single-lens reflex (DSLR) camera and a small telescope typical of introductory astronomy labs. With this equipment we believe it is possible for introductory astronomy students to take stellar spectra that are of high enough quality to distinguish between many MK spectral classes, or to determine standard B and V magnitudes. We present observational tests of this objective grating used on an 8" Schmidt-Cassegrain with a low-end, consumer DSLR camera. Some low-cost strategies for reducing the raw data are compared, with an eye toward projects ranging from individual undergraduate research projects to use by many students in a non-majors introductory astronomy lab. Toward this end we compare various trade offs between complexity of the observing and data reduction processes and the usefulness of the final results. We also describe some undergraduate astronomy education projects that this system could potentially be used for. Some of these projects could involve data-sharing collaborations between students at different institutions.

The gravitational wave experiment

NASA Technical Reports Server (NTRS)

Bertotti, B.; Ambrosini, R.; Asmar, S. W.; Brenkle, J. P.; Comoretto, G.; Giampieri, G.; Less, L.; Messeri, A.; Wahlquist, H. D.

1992-01-01

Since the optimum size of a gravitational wave detector is the wave length, interplanetary dimensions are needed for the mHz band of interest. Doppler tracking of Ulysses will provide the most sensitive attempt to date at the detection of gravitational waves in the low frequency band. The driving noise source is the fluctuations in the refractive index of interplanetary plasma. This dictates the timing of the experiment to be near solar opposition and sets the target accuracy for the fractional frequency change at 3.0 x 10 exp -14 for integration times of the order of 1000 sec. The instrumentation utilized by the experiment is distributed between the radio systems on the spacecraft and the seven participating ground stations of the Deep Space Network and Medicina. Preliminary analysis is available of the measurements taken during the Ulysses first opposition test.

Study on the Preliminary Design of ARGO-M Operation System

NASA Astrophysics Data System (ADS)

Seo, Yoon-Kyung; Lim, Hyung-Chul; Rew, Dong-Young; Jo, Jung Hyun; Park, Jong-Uk; Park, Eun-Seo; Park, Jang-Hyun

2010-12-01

Korea Astronomy and Space Science Institute has been developing one mobile satellite laser ranging system named as accurate ranging system for geodetic observation-mobile (ARGO-M). Preliminary design of ARGO-M operation system (AOS) which is one of the ARGO-M subsystems was completed in 2009. Preliminary design results are applied to the following development phase by performing detailed design with analysis of pre-defined requirements and analysis of the derived specifications. This paper addresses the preliminary design of the whole AOS. The design results in operation and control part which is a key part in the operation system are described in detail. Analysis results of the interface between operation-supporting hardware and the control computer are summarized, which is necessary in defining the requirements for the operation-supporting hardware. Results of this study are expected to be used in the critical design phase to finalize the design process.

In situ experiments to assess effects of constraints linked to caging on ecotoxicity biomarkers of the three-spined stickleback (Gasterosteus aculeatus L.).

PubMed

Le Guernic, Antoine; Sanchez, Wilfried; Palluel, Olivier; Bado-Nilles, Anne; Turies, Cyril; Chadili, Edith; Cavalié, Isabelle; Adam-Guillermin, Christelle; Porcher, Jean-Marc; Geffard, Alain; Betoulle, Stéphane; Gagnaire, Béatrice

2016-04-01

The aim of this study was to evaluate the effects of caging constraints on multiple fish biomarkers used during ecotoxicological studies (biometric data, immune and antioxidant systems, and energetic status). Two of these constraints were linked to caging: starvation and fish density in cages, and one in relation to the post-caging handling: a short transport. Three in situ experiments were conducted with three-spined sticklebacks (Gasterosteus aculeatus). The first experiment compared the effects of three densities (low, medium, and high). The second experiment compared effects of starvation in fish fed every two days with fish that were not fed. Finally comparisons between sticklebacks which have suffered a short car transport after caging and sticklebacks killed without preliminary transport were made. The lack of food had no effect on fish energetic reserves but negatively affected their condition index and their immune system. Transport and high density induced oxidative stress, defined as an overproduction of reactive oxygen species and a stimulation of the antioxidant system. These two constraints also harmed the leucocyte viability. In order not to have any impact on ecotoxicity biomarkers during in situ experiments, it is preferable to decrease fish density in cages, prevent transport before dissections, and feed fish when the caging lasts more than two weeks.

Electronic Self-report Assessment--Cancer (ESRA-C): Working towards an integrated survey system.

PubMed

Karras, Bryant T; Wolpin, Seth; Lober, William B; Bush, Nigel; Fann, Jesse R; Berry, Donna L

2006-01-01

The Clinical Informatics Research Group and Biobehavioral Nursing and Health Systems at the University of Washington are working with interdisciplinary teams to improve patient care and tracking of patient-reported symptoms and outcomes by creating an extensible web-based survey and intervention platform. The findings and cumulative experience from these processes have led to incremental improvements and variations in each new implementation of the platform. This paper presents progress in the first year of a three-year NIH study entitled Electronic Self Report Assessment--Cancer (ESRA-C). The project's goals are to enhance and evaluate the web-based computerized patient self-reporting and assessment system at the Seattle Cancer Care Alliance. Preliminary work and lessons learned in the modification of the platform and enhancements to the system will be described.

Application Of The CSRL Language To The Design Of Diagnostic Expert Systems: The Moodis Experience, A Preliminary Report

NASA Astrophysics Data System (ADS)

Bravos, Angelo; Hill, Howard; Choca, James; Bresolin, Linda B.; Bresolin, Michael J.

1986-03-01

Computer technology is rapidly becoming an inseparable part of many health science specialties. Recently, a new area of computer technology, namely Artificial Intelligence, has been applied toward assisting the medical experts in their diagnostic and therapeutic decision making process. MOODIS is an experimental diagnostic expert system which assists Psychiatry specialists in diagnosing human Mood Disorders, better known as Affective Disorders. Its diagnostic methodology is patterned after MDX, a diagnostic expert system developed at LAIR (Laboratory for Artificial Intelligence Research) of Ohio State University. MOODIS is implemented in CSRL (Conceptual Structures Representation Language) also developed at LAIR. This paper describes MOODIS in terms of conceptualization and requirements, and discusses why the MDX approach and CSRL were chosen.

Planning assistance for the NASA 30/20 GHz program. Network control architecture study.

NASA Technical Reports Server (NTRS)

Inukai, T.; Bonnelycke, B.; Strickland, S.

1982-01-01

Network Control Architecture for a 30/20 GHz flight experiment system operating in the Time Division Multiple Access (TDMA) was studied. Architecture development, identification of processing functions, and performance requirements for the Master Control Station (MCS), diversity trunking stations, and Customer Premises Service (CPS) stations are covered. Preliminary hardware and software processing requirements as well as budgetary cost estimates for the network control system are given. For the trunking system control, areas covered include on board SS-TDMA switch organization, frame structure, acquisition and synchronization, channel assignment, fade detection and adaptive power control, on board oscillator control, and terrestrial network timing. For the CPS control, they include on board processing and adaptive forward error correction control.

A spaceborne optical interferometer: The JPL CSI mission focus

NASA Astrophysics Data System (ADS)

Laskin, R. A.

1989-08-01

The JPL Control Structure Interaction (CSI) program is part of the larger NASA-wide CSI program. Within this larger context, the JPL CSI program will emphasize technology for systems that demand micron or sub-micron level control, so-called Micro-Precision Controlled Structures (u-PCS). The development of such technology will make it practical to fly missions with large optical or large precision antenna systems. In keeping with the focused nature of the desired technology, the JPL approach is to identify a focus mission, develop the focus mission CSI system design to a preliminary level, and then use this design to drive out requirements for CSI technology development in the design and analysis, ground test bed, and flight experiment areas.

A preliminary study of a cryogenic equivalence principle experiment on Shuttle

NASA Technical Reports Server (NTRS)

Everitt, C. W. F.; Worden, P. W., Jr.

1985-01-01

The Weak Equivalence Principle is the hypothesis that all test bodies fall with the same acceleration in the same gravitational field. The current limit on violations of the Weak Equivalence Principle, measured by the ratio of the difference in acceleration of two test masses to their average acceleration, is about 3 parts in one-hundred billion. It is anticipated that this can be improved in a shuttle experiment to a part in one quadrillion. Topics covered include: (1) studies of the shuttle environment, including interference with the experiment, interfacing to the experiment, and possible alternatives; (2) numerical simulations of the proposed experiment, including analytic solutions for special cases of the mass motion and preliminary estimates of sensitivity and time required; (3) error analysis of several noise sources such as thermal distortion, gas and radiation pressure effects, and mechanical distortion; and (4) development and performance tests of a laboratory version of the instrument.

Possession experiences in dissociative identity disorder: a preliminary study.

PubMed

Ross, Colin A

2011-01-01

Dissociative trance disorder, which includes possession experiences, was introduced as a provisional diagnosis requiring further study in the Diagnostic and Statistical Manual of Mental Disorders (4th ed.). Consideration is now being given to including possession experiences within dissociative identity disorder (DID) in the Diagnostic and Statistical Manual of Mental Disorders (5th ed.), which is due to be published in 2013. In order to provide empirical data relevant to the relationship between DID and possession states, I analyzed data on the prevalence of trance, possession states, sleepwalking, and paranormal experiences in 3 large samples: patients with DID from North America; psychiatric outpatients from Shanghai, China; and a general population sample from Winnipeg, Canada. Trance, sleepwalking, paranormal, and possession experiences were much more common in the DID patients than in the 2 comparison samples. The study is preliminary and exploratory in nature because the samples were not matched in any way.

Preliminary design package for prototype solar heating system

NASA Technical Reports Server (NTRS)

1976-01-01

A preliminary design review on the development of a prototype solar heating system for single family dwellings is presented. The collector, storage, transport, control, and site data acquisition subsystems are described.

A Preliminary Investigation of a Fluid-Filled ECG-Triggered Anti-G Suit.

DTIC Science & Technology

1994-02-01

the abdomen, anterior thighs, and calves. In Australia, Dr. F.S. Cotton of Sydney developed a pneumatic anti-G suit using the Royal Australian Air...Acceleration Stress: Model Studies and Preliminary Experiments. IEEE Transactions on Biomedical Engineering, Feb 1985, Vol BME -32(2):158-165. 10 13. Lambert

ICT and UD: Preliminary Study for Recommendations to Design Accessible University Courses.

PubMed

Pagliara, Silvio Marcello; Sánchez Utgé, Marta; De Anna, Lucia

2017-01-01

Starting from the Universal Design in the educational context principles, the experiences gained during the FIRB project "Net@ccessibility" and the high-education courses for teachers' specialization on special education, this research will focus on preliminary studies in order to define the recommendations for designing accessible university courses.

Factors affecting weight gain and dietary intake in Latino males residing in Mississippi: A preliminary study

USDA-ARS?s Scientific Manuscript database

Research indicates that as Latinos become more acculturated to the United States, their diet changes and they experience weight gain. There is also a high incidence of depression in this population. The purpose of this preliminary study was to examine the correlations between sociodemographic factor...

Strategic avionics technology definition studies. Subtask 3-1A: Electrical Actuation (ELA) systems

NASA Technical Reports Server (NTRS)

Pond, Charles L.; Mcdermott, William A.; Lum, Ben T. F.

1993-01-01

Electrical actuator (ELA) power efficiency and requirements are examined for space system application. Requirements for Space Shuttle effector systems are presented, along with preliminary ELA trades and selection to form a preliminary ELA system baseline. Power and energy requirements for this baseline ELA system are applicable to the Space Shuttle and similar space vehicles.

A Preliminary Study on Gender Differences in Studying Systems Analysis and Design

ERIC Educational Resources Information Center

Lee, Fion S. L.; Wong, Kelvin C. K.

2017-01-01

Systems analysis and design is a crucial task in system development and is included in a typical information systems programme as a core course. This paper presented a preliminary study on gender differences in studying a systems analysis and design course of an undergraduate programme. Results indicated that male students outperformed female…

SU-F-T-269: Preliminary Experience of Kuwait Cancer Control Center (KCCC) On IMRT Treatment Planning and Pre-Treatment Verification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sethuraman, TKR; Sherif, M; Subramanian, N

Purpose: The complexity of IMRT delivery requires pre-treatment quality assurance and plan verification. KCCC has implemented IMRT clinically in few sites and will extend to all sites. Recently, our Varian linear accelerator and Eclipse planning system were upgraded from Millennium 80 to 120 Multileaf Collimator (MLC) and from v8.6 to 11.0 respectively. Our preliminary experience on the pre-treatment quality assurance verification is discussed. Methods: Eight Breast, Three Prostate and One Hypopharynx cancer patients were planned with step and shoot IMRT. All breast cases were planned before the upgrade with 60% cases treated. The ICRU 83 recommendations were followed for themore » dose prescription and constraints to OAR for all cases. Point dose measurement was done with CIRS cylindrical phantom and PTW 0.125 cc ionization chamber. Measured dose was compared with calculated dose at the point of measurement. Map CHECK diode array phantom was used for the plan verification. Planned and measured doses were compared by applying gamma index of 3% (dose difference) / 3 mm DTA (average distance to agreement). For all cases, a plan is considered to be successful if more than 95% of the tested diodes pass the gamma test. A prostate case was chosen to compare the plan verification before and after the upgrade. Results: Point dose measurement results were in agreement with the calculated doses. The maximum deviation observed was 2.3%. The passing rate of average gamma index was measured higher than 97% for the plan verification of all cases. Similar result was observed for plan verification of the chosen prostate case before and after the upgrade. Conclusion: Our preliminary experience from the obtained results validates the accuracy of our QA process and provides confidence to extend IMRT to all sites in Kuwait.« less

Manned spacecraft electrical power systems

NASA Technical Reports Server (NTRS)

Simon, William E.; Nored, Donald L.

1987-01-01

A brief history of the development of electrical power systems from the earliest manned space flights illustrates a natural trend toward a growth of electrical power requirements and operational lifetimes with each succeeding space program. A review of the design philosophy and development experience associated with the Space Shuttle Orbiter electrical power system is presented, beginning with the state of technology at the conclusion of the Apollo Program. A discussion of prototype, verification, and qualification hardware is included, and several design improvements following the first Orbiter flight are described. The problems encountered, the scientific and engineering approaches used to meet the technological challenges, and the results obtained are stressed. Major technology barriers and their solutions are discussed, and a brief Orbiter flight experience summary of early Space Shuttle missions is included. A description of projected Space Station power requirements and candidate system concepts which could satisfy these anticipated needs is presented. Significant challenges different from Space Shuttle, innovative concepts and ideas, and station growth considerations are discussed. The Phase B Advanced Development hardware program is summarized and a status of Phase B preliminary tradeoff studies is presented.

System Description and First Application of an FPGA-Based Simultaneous Multi-Frequency Electrical Impedance Tomography

PubMed Central

Aguiar Santos, Susana; Robens, Anne; Boehm, Anna; Leonhardt, Steffen; Teichmann, Daniel

2016-01-01

A new prototype of a multi-frequency electrical impedance tomography system is presented. The system uses a field-programmable gate array as a main controller and is configured to measure at different frequencies simultaneously through a composite waveform. Both real and imaginary components of the data are computed for each frequency and sent to the personal computer over an ethernet connection, where both time-difference imaging and frequency-difference imaging are reconstructed and visualized. The system has been tested for both time-difference and frequency-difference imaging for diverse sets of frequency pairs in a resistive/capacitive test unit and in self-experiments. To our knowledge, this is the first work that shows preliminary frequency-difference images of in-vivo experiments. Results of time-difference imaging were compared with simulation results and shown that the new prototype performs well at all frequencies in the tested range of 60 kHz–960 kHz. For frequency-difference images, further development of algorithms and an improved normalization process is required to correctly reconstruct and interpreted the resulting images. PMID:27463715

User needs, benefits and integration of robotic systems in a space station laboratory

NASA Technical Reports Server (NTRS)

Farnell, K. E.; Richard, J. A.; Ploge, E.; Badgley, M. B.; Konkel, C. R.; Dodd, W. R.

1989-01-01

The methodology, results and conclusions of the User Needs, Benefits, and Integration Study (UNBIS) of Robotic Systems in the Space Station Microgravity and Materials Processing Facility are summarized. Study goals include the determination of user requirements for robotics within the Space Station, United States Laboratory. Three experiments were selected to determine user needs and to allow detailed investigation of microgravity requirements. A NASTRAN analysis of Space Station response to robotic disturbances, and acceleration measurement of a standard industrial robot (Intelledex Model 660) resulted in selection of two ranges of low gravity manipulation: Level 1 (10-3 to 10-5 G at greater than 1 Hz.) and Level 2 (less than = 10-6 G at 0.1 Hz). This included an evaluation of microstepping methods for controlling stepper motors and concluded that an industrial robot actuator can perform milli-G motion without modification. Relative merits of end-effectors and manipulators were studied in order to determine their ability to perform a range of tasks related to the three low gravity experiments. An Effectivity Rating was established for evaluating these robotic system capabilities. Preliminary interface requirements were determined such that definition of requirements for an orbital flight demonstration experiment may be established.

Study on user interface of pathology picture archiving and communication system.

PubMed

Kim, Dasueran; Kang, Peter; Yun, Jungmin; Park, Sung-Hye; Seo, Jeong-Wook; Park, Peom

2014-01-01

It is necessary to improve the pathology workflow. A workflow task analysis was performed using a pathology picture archiving and communication system (pathology PACS) in order to propose a user interface for the Pathology PACS considering user experience. An interface analysis of the Pathology PACS in Seoul National University Hospital and a task analysis of the pathology workflow were performed by observing recorded video. Based on obtained results, a user interface for the Pathology PACS was proposed. Hierarchical task analysis of Pathology PACS was classified into 17 tasks including 1) pre-operation, 2) text, 3) images, 4) medical record viewer, 5) screen transition, 6) pathology identification number input, 7) admission date input, 8) diagnosis doctor, 9) diagnosis code, 10) diagnosis, 11) pathology identification number check box, 12) presence or absence of images, 13) search, 14) clear, 15) Excel save, 16) search results, and 17) re-search. And frequently used menu items were identified and schematized. A user interface for the Pathology PACS considering user experience could be proposed as a preliminary step, and this study may contribute to the development of medical information systems based on user experience and usability.

Zonal Flow Velocimetry in Spherical Couette Flow using Acoustic Modes

NASA Astrophysics Data System (ADS)

Adams, Matthew M.; Mautino, Anthony R.; Stone, Douglas R.; Triana, Santiago A.; Lekic, Vedran; Lathrop, Daniel P.

2015-11-01

We present studies of spherical Couette flows using the technique of acoustic mode Doppler velocimetry. This technique uses rotational splittings of acoustic modes to infer the azimuthal velocity profile of a rotating flow, and is of special interest in experiments where direct flow visualization is impractical. The primary experimental system consists of a 60 cm diameter outer spherical shell concentric with a 20 cm diameter sphere, with air or nitrogen gas serving as the working fluid. The geometry of the system approximates that of the Earth's core, making these studies geophysically relevant. A turbulent shear flow is established in the system by rotating the inner sphere and outer shell at different rates. Acoustic modes of the fluid volume are excited using a speaker and measured via microphones, allowingdetermination of rotational splittings. Preliminary results comparing observed splittings with those predicted by theory are presented. While the majority of these studies were performed in the 60 cm diameter device using nitrogen gas, some work has also been done looking at acoustic modes in the 3 m diameter liquid sodium spherical Couette experiment. Prospects for measuring zonal velocity profiles in a wide variety of experiments are discussed.

Project WISH: The Emerald City

NASA Technical Reports Server (NTRS)

Oz, Hayrani; Slonksnes, Linda (Editor); Rogers, James W. (Editor); Sherer, Scott E. (Editor); Strosky, Michelle A. (Editor); Szmerekovsky, Andrew G. (Editor); Klupar, G. Joseph (Editor)

1990-01-01

The preliminary design of a permanently manned autonomous space oasis (PEMASO), including its pertinent subsystems, was performed during the 1990 Winter and Spring quarters. The purpose for the space oasis was defined and the preliminary design work was started with emphasis placed on the study of orbital mechanics, power systems and propulsion systems. A rotating torus was selected as the preliminary configuration, and overall size, mass and location of some subsystems within the station were addressed. Computer software packages were utilized to determine station transfer parameters and thus the preliminary propulsion requirements. Power and propulsion systems were researched to determine feasible configurations and many conventional schemes were ruled out. Vehicle dynamics and control, mechanical and life support systems were also studied. For each subsystem studied, the next step in the design process to be performed during the continuation of the project was also addressed.

Clinical experiences of collaborative imaging diagnosis in Shanghai district healthcare services

NASA Astrophysics Data System (ADS)

Zhang, Kai; Ling, Tonghui; Yang, Yuanyuan; Sun, Jianyong; Wang, Mingqing; Zhang, Jianguo

2016-03-01

To improve healthcare service quality with balancing healthcare resources between large and small hospitals, as well as reducing costs, each district health administration in Shanghai with more than 24 million citizens has built image-enabled electronic healthcare records (iEHR) system to share patient medical records and encourage patients to visit small hospitals for initial evaluations and preliminary diagnoses first, then go to large hospitals to have better specialists' services. We implemented solution for iEHR systems, based on the IHE XDS-I integration profile and installed the systems in more than 100 hospitals cross three districts in Shanghai and one city in Jiangsu Province in last few years. Here, we give operational results of these systems in these four districts and evaluated the performance of the systems in servicing the regional collaborative imaging diagnosis.

System Synthesis in Preliminary Aircraft Design using Statistical Methods

NASA Technical Reports Server (NTRS)

DeLaurentis, Daniel; Mavris, Dimitri N.; Schrage, Daniel P.

1996-01-01

This paper documents an approach to conceptual and preliminary aircraft design in which system synthesis is achieved using statistical methods, specifically design of experiments (DOE) and response surface methodology (RSM). These methods are employed in order to more efficiently search the design space for optimum configurations. In particular, a methodology incorporating three uses of these techniques is presented. First, response surface equations are formed which represent aerodynamic analyses, in the form of regression polynomials, which are more sophisticated than generally available in early design stages. Next, a regression equation for an overall evaluation criterion is constructed for the purpose of constrained optimization at the system level. This optimization, though achieved in a innovative way, is still traditional in that it is a point design solution. The methodology put forward here remedies this by introducing uncertainty into the problem, resulting a solutions which are probabilistic in nature. DOE/RSM is used for the third time in this setting. The process is demonstrated through a detailed aero-propulsion optimization of a high speed civil transport. Fundamental goals of the methodology, then, are to introduce higher fidelity disciplinary analyses to the conceptual aircraft synthesis and provide a roadmap for transitioning from point solutions to probabalistic designs (and eventually robust ones).

Modelling the Centers of Galaxies

NASA Technical Reports Server (NTRS)

Smith, B. F.; Miller, R. H.; Young, Richard E. (Technical Monitor)

1997-01-01

The key to studying central regions by means of nobody numerical experiments is to concentrate on the central few parsecs of a galaxy, replacing the remainder of the galaxy by a suitable boundary condition, rather after the manner in which stellar interiors can be studied without a detailed stellar atmosphere by replacing the atmosphere with a boundary condition. Replacements must be carefully designed because the long range gravitational force means that the core region is sensitive to mass outside that region and because particles can exchange between the outer galaxy and the core region. We use periodic boundary conditions, coupled with an iterative procedure to generate initial particle loads in isothermal equilibrium. Angular momentum conservation is ensured for problems including systematic rotation by a circular reflecting boundary and by integrating in a frame that rotates with the mean flow. Mass beyond the boundary contributes to the gravitational potential, but does not participate in the dynamics. A symplectic integration scheme has been developed for rotating coordinate systems. This combination works well, leading to robust configurations. Some preliminary results with this combination show that: (1) Rotating systems are extremely sensitive to non-axisymmetric external potentials, and (2) that a second core, orbiting near the main core (like the M31 second core system), shows extremely rapid orbital decay. The experimental setups will be discussed, along with preliminary results.

Hydroponics Database and Handbook for the Advanced Life Support Test Bed

NASA Technical Reports Server (NTRS)

Nash, Allen J.

1999-01-01

During the summer 1998, I did student assistance to Dr. Daniel J. Barta, chief plant growth expert at Johnson Space Center - NASA. We established the preliminary stages of a hydroponic crop growth database for the Advanced Life Support Systems Integration Test Bed, otherwise referred to as BIO-Plex (Biological Planetary Life Support Systems Test Complex). The database summarizes information from published technical papers by plant growth experts, and it includes bibliographical, environmental and harvest information based on plant growth under varying environmental conditions. I collected 84 lettuce entries, 14 soybean, 49 sweet potato, 16 wheat, 237 white potato, and 26 mix crop entries. The list will grow with the publication of new research. This database will be integrated with a search and systems analysis computer program that will cross-reference multiple parameters to determine optimum edible yield under varying parameters. Also, we have made preliminary effort to put together a crop handbook for BIO-Plex plant growth management. It will be a collection of information obtained from experts who provided recommendations on a particular crop's growing conditions. It includes bibliographic, environmental, nutrient solution, potential yield, harvest nutritional, and propagation procedure information. This handbook will stand as the baseline growth conditions for the first set of experiments in the BIO-Plex facility.

Preliminary design of a universal Martian lander

NASA Astrophysics Data System (ADS)

Norman, Timothy L.; Gaskin, David E.; Adkins, Sean; Gunawan, Mary; Johnson, Raquel; Macdonnell, David; Parlock, Andrew; Sarick, John; Bodwell, Charles; Hashimoto, Kouichi

In the next 25 years, mankind will be undertaking yet another giant leap forward in the exploration of the solar system: a manned mission to Mars. This journey will provide important information on the composition and history of both Mars and the Solar System. A manned mission will also provide the opportunity to study how humans can adapt to long term space flight conditions and the Martian environment. As part of the NASA/USRA program, nineteen West Virginia University students conducted a preliminary design of a manned Universal Martian Lander (UML). The UML's design will provide a 'universal' platform, consisting of four modules for living and laboratory experiments and a liquid-fuel propelled Manned Ascent Return Vehicle (MARV). The distinguishing feature of the UML is the 'universal' design of the modules which can be connected to form a network of laboratories and living quarters for future missions thereby reducing development and production costs. The WVU design considers descent to Mars from polar orbit, a six month surface stay, and ascent for rendezvous. The design begins with an unmanned UML landing at Elysium Mons followed by the manned UML landing nearby. During the six month surface stay, the eight modules will be assembled to form a Martian base where scientific experiments will be performed. The mission will also incorporate hydroponic plant growth into a Controlled Ecological Life Support System (CELSS) for water recycling, food production, and to counteract psychological effects of living on Mars. In situ fuel production for the MARV will be produced from gases in the Martian atmosphere. Following surface operations, the eight member crew will use the MARV to return to the Martian Transfer Vehicle (MTV) for the journey home to Earth.

Preliminary design of a universal Martian lander

NASA Technical Reports Server (NTRS)

Norman, Timothy L.; Gaskin, David E.; Adkins, Sean; Gunawan, Mary; Johnson, Raquel; Macdonnell, David; Parlock, Andrew; Sarick, John; Bodwell, Charles; Hashimoto, Kouichi

1993-01-01

In the next 25 years, mankind will be undertaking yet another giant leap forward in the exploration of the solar system: a manned mission to Mars. This journey will provide important information on the composition and history of both Mars and the Solar System. A manned mission will also provide the opportunity to study how humans can adapt to long term space flight conditions and the Martian environment. As part of the NASA/USRA program, nineteen West Virginia University students conducted a preliminary design of a manned Universal Martian Lander (UML). The UML's design will provide a 'universal' platform, consisting of four modules for living and laboratory experiments and a liquid-fuel propelled Manned Ascent Return Vehicle (MARV). The distinguishing feature of the UML is the 'universal' design of the modules which can be connected to form a network of laboratories and living quarters for future missions thereby reducing development and production costs. The WVU design considers descent to Mars from polar orbit, a six month surface stay, and ascent for rendezvous. The design begins with an unmanned UML landing at Elysium Mons followed by the manned UML landing nearby. During the six month surface stay, the eight modules will be assembled to form a Martian base where scientific experiments will be performed. The mission will also incorporate hydroponic plant growth into a Controlled Ecological Life Support System (CELSS) for water recycling, food production, and to counteract psychological effects of living on Mars. In situ fuel production for the MARV will be produced from gases in the Martian atmosphere. Following surface operations, the eight member crew will use the MARV to return to the Martian Transfer Vehicle (MTV) for the journey home to Earth.

Analysis of Spatial Autocorrelation for Optimal Observation Network in Korea

NASA Astrophysics Data System (ADS)

Park, S.; Lee, S.; Lee, E.; Park, S. K.

2016-12-01

Many studies for improving prediction of high-impact weather have been implemented, such as THORPEX (The Observing System Research and Predictability Experiment), FASTEX (Fronts and Atlantic Storm-Track Experiment), NORPEX (North Pacific Experiment), WSR/NOAA (Winter Storm Reconnaissance), and DOTSTAR (Dropwindsonde Observations for Typhoon Surveillance near the TAiwan Region). One of most important objectives in these studies is to find effects of observation on forecast, and to establish optimal observation network. However, there are lack of such studies on Korea, although Korean peninsula exhibits a highly complex terrain so it is difficult to predict its weather phenomena. Through building the future optimal observation network, it is necessary to increase utilization of numerical weather prediction and improve monitoring·tracking·prediction skills of high-impact weather in Korea. Therefore, we will perform preliminary study to understand the spatial scale for an expansion of observation system through Spatial Autocorrelation (SAC) analysis. In additions, we will develop a testbed system to design an optimal observation network. Analysis is conducted with Automatic Weather System (AWS) rainfall data, global upper air grid observation (i.e., temperature, pressure, humidity), Himawari satellite data (i.e., water vapor) during 2013-2015 of Korea. This study will provide a guideline to construct observation network for not only improving weather prediction skill but also cost-effectiveness.

Space Shuttle flying qualities and flight control system assessment study, phase 2

NASA Technical Reports Server (NTRS)

Myers, T. T.; Johnston, D. E.; Mcruer, D. T.

1983-01-01

A program of flying qualities experiments as part of the Orbiter Experiments Program (OEX) is defined. Phase 1, published as CR-170391, reviewed flying qualities criteria and shuttle data. The review of applicable experimental and shuttle data to further define the OEX plan is continued. An unconventional feature of this approach is the use of pilot strategy model identification to relate flight and simulator results. Instrumentation, software, and data analysis techniques for pilot model measurements are examined. The relationship between shuttle characteristics and superaugmented aircraft is established. STS flights 1 through 4 are reviewed from the point of view of flying qualities. A preliminary plan for a coordinated program of inflight and simulator research is presented.

Modeling of the charge-state separation at ITEP experimental facility for material science based on a Bernas ion source.

PubMed

Barminova, H Y; Saratovskyh, M S

2016-02-01

The experiment automation system is supposed to be developed for experimental facility for material science at ITEP, based on a Bernas ion source. The program CAMFT is assumed to be involved into the program of the experiment automation. CAMFT is developed to simulate the intense charged particle bunch motion in the external magnetic fields with arbitrary geometry by means of the accurate solution of the particle motion equation. Program allows the consideration of the bunch intensity up to 10(10) ppb. Preliminary calculations are performed at ITEP supercomputer. The results of the simulation of the beam pre-acceleration and following turn in magnetic field are presented for different initial conditions.

Markov chains for testing redundant software

NASA Technical Reports Server (NTRS)

White, Allan L.; Sjogren, Jon A.

1988-01-01

A preliminary design for a validation experiment has been developed that addresses several problems unique to assuring the extremely high quality of multiple-version programs in process-control software. The procedure uses Markov chains to model the error states of the multiple version programs. The programs are observed during simulated process-control testing, and estimates are obtained for the transition probabilities between the states of the Markov chain. The experimental Markov chain model is then expanded into a reliability model that takes into account the inertia of the system being controlled. The reliability of the multiple version software is computed from this reliability model at a given confidence level using confidence intervals obtained for the transition probabilities during the experiment. An example demonstrating the method is provided.

Modeling of the charge-state separation at ITEP experimental facility for material science based on a Bernas ion source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barminova, H. Y., E-mail: barminova@bk.ru; Saratovskyh, M. S.

2016-02-15

The experiment automation system is supposed to be developed for experimental facility for material science at ITEP, based on a Bernas ion source. The program CAMFT is assumed to be involved into the program of the experiment automation. CAMFT is developed to simulate the intense charged particle bunch motion in the external magnetic fields with arbitrary geometry by means of the accurate solution of the particle motion equation. Program allows the consideration of the bunch intensity up to 10{sup 10} ppb. Preliminary calculations are performed at ITEP supercomputer. The results of the simulation of the beam pre-acceleration and following turnmore » in magnetic field are presented for different initial conditions.« less

Temperature and thermal emissivity of the surface of Neptune's satellite Triton

NASA Technical Reports Server (NTRS)

Nelson, Robert M.; Smythe, William D.; Wallis, Brad D.; Horn, Linda J.; Lane, Arthur L.; Mayo, Marvin J.

1990-01-01

Analysis of the preliminary results from the Voyager mission to the Neptune system has provided the scientific community with several methods by which the temperature of Neptune's satellite Triton may be determined. If the 37.5 K surface temperature reported by several Voyager investigations is correct, then the photometry reported by the imaging experiment on Voyager requires that Triton's surface have a remarkably low emissivity. Such a low emissivity is not required in order to explain the photometry from the photopolarimeter experiment on Voyager. A low emissivity would be inconsistent with Triton having a rough surface at the about 100-micron scale as might be expected given the active renewal processes which appear to dominate Triton's surface.

Towards monitoring real-time cellular response using an integrated microfluidics-MALDI/nESI-ion mobility-mass spectrometry platform

PubMed Central

Enders, Jeffrey R.; Marasco, Christina C.; Kole, Ayeeshik; Nguyen, Bao; Sundarapandian, Sevugarajan; Seale, Kevin T.; Wikswo, John P.; McLean, John A.

2014-01-01

The combination of microfluidic cell trapping devices with ion mobility-mass spectrometry offers the potential for elucidating in real time the dynamic responses of small populations of cells to paracrine signals, changes in metabolite levels, and delivery of drugs and toxins. Preliminary experiments examining peptides in methanol and recording the interactions of yeast and Jurkat cells with their superfusate have identified instrumental setup and control parameters and on-line desalting procedures. Numerous initial experiments demonstrate and validate this new instrumental platform. Future outlooks and potential applications are addressed, specifically how this instrumentation may be used for fully automated systems biology studies of the significantly interdependent, dynamic internal workings of cellular metabolic and signaling pathways. PMID:21073240

Preliminary analysis of pilot ratings of 'part line' information importance

NASA Technical Reports Server (NTRS)

Pritchett, Amy; Hansman, R. John

1993-01-01

With the introduction of digital datalink communications into the Air Traffic Control (ATC) system, there is concern over the potential loss of situational awareness by flight crews due to the reduction in the 'Party Line Information' (PLI). This information is available to the pilot by overhearing communications between ATC and other aircraft. A survey was distributed to determine current PLI use by several pilot operational groups, experience levels and geographic regions. The survey identified numerous important elements. PLI was rated the highest for operations near or on approach to the airport. Several significant variations were found between pilots from different operational groups and experience levels. Traffic and weather information were the most frequently cited as information required to obtain global situation awareness.

Preliminary Analysis of Pilot Ratings of "Party Line" Information Importance

NASA Technical Reports Server (NTRS)

Pritchett, Amy; Hansman, R. John

1993-01-01

With the introduction of digital data link communications into the ATC system, there is concern over the potential loss of situational awareness by flight crews due to the reduction in the 'Party Line' Information (PLI). This information is available to the pilot by overhearing communications between ATC and other aircraft. A survey was distributed to determine current PLI use by several pilot operational groups, experience levels and geographic regions. The survey identified numerous important elements. PLI was rated the highest for operations near or on approach to the airport. Several significant variations were found between pilots from different operational groups and experience levels. Traffic and weather information were the most frequently cited as information required to obtain global situation awareness.

A preliminary study on the development of electronic pump system using Arduino controller

NASA Astrophysics Data System (ADS)

Salleh, Mohd Sharil; Miskon, Azizi; Hashim, Fakroul Ridzuan

2018-02-01

The implications of treatment using hemodialysis machine and equipment remain speculative. Most studies, case reviews and medical surveys have shown statistics of side effects of hypertension while undergo a treatment using hemodialysis machine. Therefore, a specific action must be taken to prevent the effects of hypertension during treatment especially using hemodialysis machine. In order to reduce this matter in terms of frequency of hypertension while undergo hemodialysis treatment, many approach have been undertaken for improvement. For the beginning, this project reviews the technique of controlling instantaneous blood pressure for normal and hypertension stage and describe the challenges faced by a researcher during experiment to match human stability. The methodology used in this project is to develop one electronics pump system using Arduino controller for transferring liquid (a tap water) from a tank to another tank. The liquid flow rate was measured by using flow sensor where it located at input and output part. This project has decided to focus on flow rate range from 300 mL/min to 900 mL/min. Results shows an efficiency for speed 30 is 97.96%, speed 50 is 100.15%, speed 130 is 99.54% and speed 200 is 99.87%. A range of efficiency for this preliminary study on the development of Electronic Pump System are from 97.96% to 100.15%. In addition, analysis and simulation of the system delivers a better performance efficiency.

Definition study for an extended manned test of a regenerative life support system, preliminary test plan

NASA Technical Reports Server (NTRS)

1971-01-01

A preliminary plan and procedure are presented for conducting an extended manned test program for a regenerative life support system. Emphasis will be placed on elements associated with long-term system operation and long-term uninterrupted crew confinement.

77 FR 19011 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-29

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On February 6, 2012, Spartanburg Water System... Schneider, General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251, Spartanburg, South...

Textural changes of FER-A peridotite in time series piston-cylinder experiments at 1.0 GPa, 1300°C

NASA Astrophysics Data System (ADS)

Schwab, B. E.; Mercer, C. N.; Johnston, A.

2012-12-01

A series of eight 1.0 GPa, 1300°C partial melting experiments were performed using FER-A peridotite starting material to investigate potential textural changes in the residual crystalline phases over time. Powdered peridotite with a layer of vitreous carbon spheres as a melt sink were sealed in graphite-lined Pt capsules and run in CaF2 furnace assemblies in 1.27cm piston-cylinder apparatus at the University of Oregon. Run durations ranged from 4 to 128 hours. Experimental charges were mounted in epoxy, cut, and polished for analysis. In a first attempt to quantify the mineral textures, individual 500x BSE images were collected from selected, representative locations on each of the experimental charges using the FEI Quanta 250 ESEM at Humboldt State University. Noran System Seven (NSS) EDS system was used to collect x-ray maps (spectral images) to aid in identification of phases. A combination of image analysis techniques within NSS and ImageJ software are being used to process the images and quantify the mineral textures observed. The goals are to quantify the size, shape, and abundance of residual olivine (ol), orthopyroxene (opx), clinopyroxene (cpx), and spinel crystals within the selected sample areas of the run products. Additional work will be done to compare the results of the selected areas with larger (lower magnification) images acquired using the same techniques. Preliminary results indicate that measurements of average grain area, minimum grain area, and average, maximum, and minimum grain perimeter show the greatest change (generally decreasing) in measurements for ol, opx, and cpx between the shortest-duration, 4-hour, experiment and the subsequent, 8-hour, experiment. The largest relative change in nearly all of these measurements appears to be for cpx. After the initial decrease, preliminary measurements remain relatively constant for ol, opx, and cpx, respectively, in experiments from 8 to 128 hours in duration. In contrast, measured parameters of spinel grains increase from the 4-hour to 8-hour experiment and continue to fluctuate over the time interval investigated. Spinel also represents the smallest number of individual grains (average n = 25) in any experiment. Average aspect ratios for all minerals remain relatively constant (~1.5-2) throughout the time series. Additional measurements and refinements are underway.

The Viking biological investigation - Preliminary results

NASA Technical Reports Server (NTRS)

Klein, H. P.; Oyama, V. I.; Berdahl, B. J.; Horowitz, N. H.; Hobby, G. L.; Levin, G. V.; Straat, P. A.; Lederberg, J.; Rich, A.; Hubbard, J. S.

1976-01-01

A preliminary progress report is presented for the Viking biological investigation through its first month. The carbon assimilation, gas exchange, and labeled release experiments are described in detail, and the chronology of the experiments is outlined. For the first experiment, it is found that a small amount of gas was converted into organic material in one sample and that heat treatment of a duplicate sample prevented such conversion. In the second experiment, a substantial amount of O2 was detected along with significant increases in CO2 and small changes in N2. In the third experiment, a significant amount of radioactive gas was evolved from one sample, but not from a duplicate heat-treated sample. Possible biological and nonbiological interpretations are considered for these results. It is concluded that while the experiments provide clear evidence for the occurrence of chemical reactions and while the results do not violate any prima facie criteria for biological processes, a definitive answer cannot yet be given to the question of whether life exists on Mars.

Informatics in radiology: web-based preliminary reporting system for radiology residents with PACS integration.

PubMed

O'Connell, Timothy; Chang, Debra

2012-01-01

While on call, radiology residents review imaging studies and issue preliminary reports to referring clinicians. In the absence of an integrated reporting system at the training sites of the authors' institution, residents were typing and faxing preliminary reports. To partially automate the on-call resident workflow, a Web-based system for resident reporting was developed by using the free open-source xAMP Web application framework and an open-source DICOM (Digital Imaging and Communications in Medicine) software toolkit, with the goals of reducing errors and lowering barriers to education. This reporting system integrates with the picture archiving and communication system to display a worklist of studies. Patient data are automatically entered in the preliminary report to prevent identification errors and simplify the report creation process. When the final report for a resident's on-call study is available, the reporting system queries the report broker for the final report, and then displays the preliminary report side by side with the final report, thus simplifying the review process and encouraging review of all of the resident's reports. The xAMP Web application framework should be considered for development of radiology department informatics projects owing to its zero cost, minimal hardware requirements, ease of programming, and large support community.

A preliminary discussion of gravitational physics experiments for the Spacelab era

NASA Technical Reports Server (NTRS)

Decher, R.; Winkler, C. G.

1976-01-01

An overview of past, present, and proposed future experiments in gravitational physics is given. These experiments are concerned with the measurement of relativistic gravity effects to test theories of gravitation. Certain experiments which could be performed on shuttle and Spacelab missions and the potential of Spacelab for gravitation physics research are discussed.

Orbital transfer rocket engine technology 7.5K-LB thrust rocket engine preliminary design

NASA Technical Reports Server (NTRS)

Harmon, T. J.; Roschak, E.

1993-01-01

A preliminary design of an advanced LOX/LH2 expander cycle rocket engine producing 7,500 lbf thrust for Orbital Transfer vehicle missions was completed. Engine system, component and turbomachinery analysis at both on design and off design conditions were completed. The preliminary design analysis results showed engine requirements and performance goals were met. Computer models are described and model outputs are presented. Engine system assembly layouts, component layouts and valve and control system analysis are presented. Major design technologies were identified and remaining issues and concerns were listed.

4MOST systems engineering: from conceptual design to preliminary design review

NASA Astrophysics Data System (ADS)

Bellido-Tirado, Olga; Frey, Steffen; Barden, Samuel C.; Brynnel, Joar; Giannone, Domenico; Haynes, Roger; de Jong, Roelof S.; Phillips, Daniel; Schnurr, Olivier; Walcher, Jakob; Winkler, Roland

2016-08-01

The 4MOST Facility is a high-multiplex, wide-field, brief-fed spectrograph system for the ESO VISTA telescope. It aims to create a world-class spectroscopic survey facility unique in its combination of wide-field multiplex, spectral resolution, spectral coverage, and sensitivity. At the end of 2014, after a successful concept optimization design phase, 4MOST entered into its Preliminary Design Phase. Here we present the process and tools adopted during the Preliminary Design Phase to define the subsystems specifications, coordinate the interface control documents and draft the system verification procedures.

Introduction to the arcopter arc wing and the Bertelsen effect for positive pitch stability and control

NASA Technical Reports Server (NTRS)

Bertelsen, W. D.

1979-01-01

A brief report, offered on a wing design, new in geometry, construction, and flight characteristics. Preliminary wind tunnel data on a three-dimensional model was well as some full-scale man-carrying test results are included. There are photos of all phases of the experiments and some figures which serve to illustrate the Bertelsen Effect, a unique focus of aerodynamic forces in the arc wing system which allows the attainment of high lift coefficients with the maintenance of pitch stability and control.

Surface energy fluxes in complex terrain

NASA Technical Reports Server (NTRS)

Reiter, E. R.; Sheaffer, J. D.; Bossert, J. E.

1986-01-01

The emphasis of the 1985 NASA project activity was on field measurements of wind data and heat balance data. Initiatives included a 19 station mountaintop monitoring program, testing and refining the surface flux monitoring systems and packing and shipping equipment to the People's Republic of China in preparation for the 1986 Tibet Experiment. Other work included more extensive analyses of the 1984 Gobi Desert and Rocky Mountain observations plus some preliminary analyses of the 1985 mountaintop network data. Details of our field efforts are summarized and results of our data analyses are presented.

Air-Ground Integration: Preliminary Results from the Coalition Attack Guidance Experiment (The International C2 Journal Volume 5, Number 3, 2011)

DTIC Science & Technology

2011-01-01

Mitchell (DNK), Royal Danish Defence College Sandeep Mulgund (USA), The MITRE Corporation Mark Nissen (USA), Naval Postgraduate School Mink Spaans (NLD...Research Management 25(1): 28-33. Cash, J.I., Jr., F.W. McFarlan, J.L. McKenney, and M.R. Vitale. 1988. Corporate Information Systems Management 2nd...Between Structure and Technology. In Handbook of Organizational Design vol. 2: 3-38, eds. P. C. Nystrom and W. H. Starbuck . New York, NY: Oxford

Systematic Study of Three-Nucleon System Dynamics in Deuteron-Proton Breakup Reaction

NASA Astrophysics Data System (ADS)

Kozela, A.; Ciepał, I.; Garbacz, M.; Jamróz, B.; Kłos, B.; Kistryn, St.; Khatri, G.; Kuboś, J.; Kulessa, P.; Liptak, A.; Parol, W.; Rusnok, A.; Sȩkowski, P.; Skwira-Chalot, I.; Stephan, E.; Wilczek, A.; Włoch, B.; Zejma, J.

2017-03-01

We report on preliminary results of the first measurement of elastic scattering of protons from deuterons and proton induced deuteron breakup at proton beam energy of 108 MeV conducted at new Cyclotron Center Bronowice IFJ PAN in Kraków. The experiment is aimed at precise determination of the differential cross section for extensive set of kinematical configurations in a wide range of angular acceptance. In the first data taking run the average statistical per-point accuracy of about 5% has been reached.

Preliminary results in implementing a model of the world economy on the CYBER 205: A case of large sparse nonsymmetric linear equations

NASA Technical Reports Server (NTRS)

Szyld, D. B.

1984-01-01

A brief description of the Model of the World Economy implemented at the Institute for Economic Analysis is presented, together with our experience in converting the software to vector code. For each time period, the model is reduced to a linear system of over 2000 variables. The matrix of coefficients has a bordered block diagonal structure, and we show how some of the matrix operations can be carried out on all diagonal blocks at once.

Precision star-tracking telescope

NASA Technical Reports Server (NTRS)

Fairbank, W. M.; Everitt, C. W. F.

1972-01-01

The design, construction, and preliminary testing of a new high accuracy star tracking telescope for the laboratory model of the Stanford gyro relativity experiment are described. The function of the telescope in the final flight experiment is to define (by reference to a suitable star) a direction in space for comparison with the relativistic precession of a group of gyroscopes. The design of the telescope has been strongly affected by designs for other portions of the overall experiments, for example the gyroscopes, the attitude control system of the satellite, and the instrumentation system used in processing relativity data. Main goals for the star tracker are: (1) independent readout of angular position in two planes; (2) absolute null stability over a one year period of mechanical parts; (3) readout linear to 0.001 arc-seconds over + or - 0.05 arc-second; (4) noise performance leading to a resolution of 0.05 arc-second in 0.1 second observation time of the chosen reference star; and (5) provision for automatic gain control capable of matching the gains of the gyroscopes and telescope readouts to 1% or better.

Experiments on Adaptive Techniques for Host-Based Intrusion Detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

DRAELOS, TIMOTHY J.; COLLINS, MICHAEL J.; DUGGAN, DAVID P.

2001-09-01

This research explores four experiments of adaptive host-based intrusion detection (ID) techniques in an attempt to develop systems that can detect novel exploits. The technique considered to have the most potential is adaptive critic designs (ACDs) because of their utilization of reinforcement learning, which allows learning exploits that are difficult to pinpoint in sensor data. Preliminary results of ID using an ACD, an Elman recurrent neural network, and a statistical anomaly detection technique demonstrate an ability to learn to distinguish between clean and exploit data. We used the Solaris Basic Security Module (BSM) as a data source and performed considerablemore » preprocessing on the raw data. A detection approach called generalized signature-based ID is recommended as a middle ground between signature-based ID, which has an inability to detect novel exploits, and anomaly detection, which detects too many events including events that are not exploits. The primary results of the ID experiments demonstrate the use of custom data for generalized signature-based intrusion detection and the ability of neural network-based systems to learn in this application environment.« less

The Importance of Conducting Life Sciences Experiments on the Deep Space Gateway Platform

NASA Technical Reports Server (NTRS)

Bhattacharya, S.

2018-01-01

Over the last several decades important information has been gathered by conducting life science experiments on the Space Shuttle and on the International Space Station. It is now time to leverage that scientific knowledge, as well as aspects of the hardware that have been developed to support the biological model systems, to NASA's next frontier - the Deep Space Gateway. In order to facilitate long duration deep space exploration for humans, it is critical for NASA to understand the effects of long duration, low dose, deep space radiation on biological systems. While carefully controlled ground experiments on Earth-based radiation facilities have provided valuable preliminary information, we still have a significant knowledge gap on the biological responses of organisms to chronic low doses of the highly ionizing particles encountered beyond low Earth orbit. Furthermore, the combined effects of altered gravity and radiation have the potential to cause greater biological changes than either of these parameters alone. Therefore a thorough investigation of the biological effects of a cis-lunar environment will facilitate long term human exploration of deep space.

Preliminary Report of NRC Twin Otter Operations in the 1997 Southern Great Plains Experiment

NASA Technical Reports Server (NTRS)

MacPherson, J. Ian

1997-01-01

From June 18 to July 17, 1997, the NRC Twin Otter atmospheric research aircraft was operated from Oklahoma City, U.S.A., in the Southern Great Plains 1997 (SGP97) Hydrology Experiment. The primary role of the aircraft was to measure the vertical fluxes of sensible and latent heat, CO2, ozone and momentum in the atmospheric boundary layer, along with supporting meteorological and radiometric data. Approximately 400 flux runs and 100 soundings were flown in 27 project flights over rural areas near Oklahoma City. This preliminary report documents the flight program, lists the instrumentation aboard the aircraft, and presents a summary of run-averaged data from each flux run. These data are from the in-field analysis and must be considered preliminary. A re-analysis incorporating updated calibrations is planned for the fall of 1997 followed by a more comprehensive technical report.

Chemical Analysis of the Moon at the Surveyor VII Landing Site: Preliminary Results.

PubMed

Turkevich, A L; Franzgrote, E J; Patterson, J H

1968-10-04

The alpha-scattering experiment aboard Surveyor VII has provided a chemical analysis of the moon in the area of the crater Tycho. The preliminary results indicate a chemical composition similar to that already found at two mare sites, but with a lower concentration of elements of the iron group (titanium through copper).

Preliminary Analysis of Fluctuations in the Received Uplink-Beacon-Power Data Obtained From the GOLD Experiments

NASA Technical Reports Server (NTRS)

Jeganathan, M.; Wilson, K. E.; Lesh, J. R.

1996-01-01

Uplink data from recent free-space optical communication experiments carried out between the Table Mountain Facility and the Japanese Engineering Test Satellite are used to study fluctuations caused by beam propagation through the atmosphere. The influence of atmospheric scintillation, beam wander and jitter, and multiple uplink beams on the statistics of power received by the satellite is analyzed and compared to experimental data. Preliminary analysis indicates the received signal obeys an approximate lognormal distribution, as predicted by the weak-turbulence model, but further characterization of other sources of fluctuations is necessary for accurate link predictions.

Preliminary analysis of fluctuations in the received uplink-beacon-power data obtained from the GOLD experiments

NASA Technical Reports Server (NTRS)

Jeganathan, M.; Wilson, K. E.; Lesh, J. R.

1996-01-01

Uplink data from recent free-space optical communication experiments carried out between the Table Mountain Facility and the Japanese Engineering Test Satellite are used to study fluctuations caused by beam propagation through the atmosphere. The influence of atmospheric scintillation, beam wander and jitter, and multiple uplink beams on the statistics of power received by the satellite is analyzed and compared to experimental data. Preliminary analysis indicates the received signal obeys an approximate lognormal distribution, as predicted by the weak-turbulence model, but further characterization of other sources of fluctuations is necessary for accurate link predictions.

77 FR 16220 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On December 20, 2011, Spartanburg Water System... Contact: Ms. Sue Schneider, General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251...

76 FR 67179 - Spartanburg Water System; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-31

... Water System; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On June 23, 2011, Spartanburg Water System (Spartanburg..., General Manager, Spartanburg Water, 200 Commerce Street, P.O. Box 251, Spartanburg, South Carolina 29304...

Space telescope observatory management system preliminary test and verification plan

NASA Technical Reports Server (NTRS)

Fritz, J. S.; Kaldenbach, C. F.; Williams, W. B.

1982-01-01

The preliminary plan for the Space Telescope Observatory Management System Test and Verification (TAV) is provided. Methodology, test scenarios, test plans and procedure formats, schedules, and the TAV organization are included. Supporting information is provided.

Preliminary evaluation of user terminals for an automated pilot briefing system

DOT National Transportation Integrated Search

1976-08-01

This report describes a preliminary evaluation of various user terminal concepts for an automated aviation pilot weather briefing and flight plan filing system. Terminals embodying differing operational concepts were used by volunteer general aviatio...

Astrionic system optimization and modular astrionics for NASA missions after 1974. Preliminary definition of astrionic system for space tug Mission Vehicle Payload (MVP)

NASA Technical Reports Server (NTRS)

1970-01-01

Results of preliminary studies to define the space tug astrionic system, subsystems, and components to meet requirements for a variety of missions are reported. Emphasis is placed on demonstration of the modular astrionics approach in the design of the space tug astrionic system.

Internally insulated thermal storage system development program

NASA Technical Reports Server (NTRS)

Scott, O. L.

1980-01-01

A cost effective thermal storage system for a solar central receiver power system using molten salt stored in internally insulated carbon steel tanks is described. Factors discussed include: testing of internal insulation materials in molten salt; preliminary design of storage tanks, including insulation and liner installation; optimization of the storage configuration; and definition of a subsystem research experiment to demonstrate the system. A thermal analytical model and analysis of a thermocline tank was performed. Data from a present thermocline test tank was compared to gain confidence in the analytical approach. A computer analysis of the various storage system parameters (insulation thickness, number of tanks, tank geometry, etc.,) showed that (1) the most cost-effective configuration was a small number of large cylindrical tanks, and (2) the optimum is set by the mechanical constraints of the system, such as soil bearing strength and tank hoop stress, not by the economics.

Internally insulated thermal storage system development program

NASA Astrophysics Data System (ADS)

Scott, O. L.

1980-03-01

A cost effective thermal storage system for a solar central receiver power system using molten salt stored in internally insulated carbon steel tanks is described. Factors discussed include: testing of internal insulation materials in molten salt; preliminary design of storage tanks, including insulation and liner installation; optimization of the storage configuration; and definition of a subsystem research experiment to demonstrate the system. A thermal analytical model and analysis of a thermocline tank was performed. Data from a present thermocline test tank was compared to gain confidence in the analytical approach. A computer analysis of the various storage system parameters (insulation thickness, number of tanks, tank geometry, etc.,) showed that (1) the most cost-effective configuration was a small number of large cylindrical tanks, and (2) the optimum is set by the mechanical constraints of the system, such as soil bearing strength and tank hoop stress, not by the economics.

New techniques in television to provide research in three-dimensional real-time or near real-time imagery and reduced cost systems for teleconferencing and educational uses, part 1

NASA Technical Reports Server (NTRS)

Pao, Y. H.; Claspy, P.; Allen, J. E.; Merat, F.

1979-01-01

The results are presented of a continuing research and development program the objective of which is to develop a reduced bandwidth television system and a technique for television transmission of holograms. The result of the former is a variable frame rate television system, the operation of which was demonstrated for both black-and-white and color signals. This system employs a novel combination of the inexpensive mass storage capacity of a magnetic disc with the reliability of a digital system for time expansion and compression. Also reported are the results of a theoretical analysis and preliminary feasibility experiment of an innovative system for television transmission of holograms using relatively conventional TV equipment along with a phase modulated reference wave for production of the original interference pattern.

The Systems SOAP Note: A Systems Learning Tool.

PubMed

Mitsuishi, Fumi; Young, John Q; Leary, Mark; Dilley, James; Mangurian, Christina

2016-02-01

Systems-based practice (SBP) is the only Accreditation Council for Graduate Medical Education (ACGME) competency concerned with public health and is relatively neglected in residency curricula. A tool was developed and pilot-tested to improve SBP learning on inpatient psychiatry rotations. A four-step approach was used: (1) literature review, (2) expert consultation, (3) tool development, and (4) pilot testing on four cases and evaluation for completion time and preliminary efficacy. Out of 51 SBP articles, six (12%) focused on psychiatric residency programs, and none had a practical SBP learning tool. The "systems SOAP (subjective, objective, assessment, plan) note" (S-SOAP) was structured after a clinical SOAP note and was easy to use (mean completion time = 60 min), and residents self-reported more insight into systems issues. The S-SOAP tool was effectively integrated into clinical experience and provided insight into systemic complexities. Future research should assess SBP knowledge acquisition after the use of such tools.

PAR -- Interface to the ADAM Parameter System

NASA Astrophysics Data System (ADS)

Currie, Malcolm J.; Chipperfield, Alan J.

PAR is a library of Fortran subroutines that provides convenient mechanisms for applications to exchange information with the outside world, through input-output channels called parameters. Parameters enable a user to control an application's behaviour. PAR supports numeric, character, and logical parameters, and is currently implemented only on top of the ADAM parameter system. The PAR library permits parameter values to be obtained, without or with a variety of constraints. Results may be put into parameters to be passed onto other applications. Other facilities include setting a prompt string, and suggested defaults. This document also introduces a preliminary C interface for the PAR library -- this may be subject to change in the light of experience.

Measurement data preprocessing in a radar-based system for monitoring of human movements

NASA Astrophysics Data System (ADS)

Morawski, Roman Z.; Miȩkina, Andrzej; Bajurko, Paweł R.

2015-02-01

The importance of research on new technologies that could be employed in care services for elderly people is highlighted. The need to examine the applicability of various sensor systems for non-invasive monitoring of the movements and vital bodily functions, such as heart beat or breathing rhythm, of elderly persons in their home environment is justified. An extensive overview of the literature concerning existing monitoring techniques is provided. A technological potential behind radar sensors is indicated. A new class of algorithms for preprocessing of measurement data from impulse radar sensors, when applied for elderly people monitoring, is proposed. Preliminary results of numerical experiments performed on those algorithms are demonstrated.

Preliminary flight results from the second U.S. Microgravity Payload (USMP-2)

NASA Technical Reports Server (NTRS)

Curreri, Peter; Reiss, Donald

1994-01-01

The second U.S. Microgravity Payload (USMP-2) was flown on the Space Shuttle in March 1994. It carried four major microgravity experiments plus a sophisticated accelerometer system to record the microgravity environment during USMP-2 operations. The USMP program is designed to accommodate experiments requiring extensive resources short of a full Spacelab mission, and the experiments are remotely operated and monitored. Results are reviewed from the four experiments: the Advanced Automated Directional Solidification Facility (AADSF), the Isothermal Dendrite Growth Experiment (IDGE), the Materiel por Etude des Phenomenes Interessant la Soldification sur Terre et en Orbite (MEPHISTO), and the Critical Fluid Light Scattering Experiment (Zeno). AASDF grew what is expected to be the largest steady-state sample ever of HgCdTe during 240 hours of operation. IDGE provided 60 growth cycles over a wide range of supercooling conditions studying the dendritic solidification of succinonitrile. MEPHISTO achieved 55 melt-solidify cycles and grew over 1 m of Bi/Sn alloy. Zeno located the critical point temperature for liquid Xe to 0.00001 K. IDGE and Zeno also provided the most extensive demonstrations to date of telescience.

General characteristics of preliminary data processing in the Copernicus experiment

NASA Technical Reports Server (NTRS)

Ziolkovski, K.; Kossatski, K.

1975-01-01

Data from the 'Copernicus' experiment is processed in four stages: setting up of basic arrays, data calibration, graphical display of results, and assignment of results to navigation parameters. Each stage is briefly discussed.