40 CFR Table 3 to Subpart Kkkkk of... - Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 14 2013-07-01 2013-07-01 false Work Practice Standards 3 Table 3 to..., Subpt. KKKKK, Table 3 Table 3 to Subpart KKKKK of Part 63—Work Practice Standards As stated in § 63.8555, you must comply with each work practice standard in the following table that applies to you. For...

40 CFR Table 3 to Subpart Sssss of... - Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Work Practice Standards 3 Table 3 to.... 63, Subpt. SSSSS, Table 3 Table 3 to Subpart SSSSS of Part 63—Work Practice Standards As stated in § 63.9788, you must comply with the work practice standards for affected sources in the following table...

40 CFR Table 3 to Subpart Kkkkk of... - Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 13 2011-07-01 2011-07-01 false Work Practice Standards 3 Table 3 to..., Subpt. KKKKK, Table 3 Table 3 to Subpart KKKKK of Part 63—Work Practice Standards As stated in § 63.8555, you must comply with each work practice standard in the following table that applies to you. For...

40 CFR Table 3 to Subpart Kkkkk of... - Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 13 2010-07-01 2010-07-01 false Work Practice Standards 3 Table 3 to..., Subpt. KKKKK, Table 3 Table 3 to Subpart KKKKK of Part 63—Work Practice Standards As stated in § 63.8555, you must comply with each work practice standard in the following table that applies to you. For...

Participatory ergonomics simulation of hospital work systems: The influence of simulation media on simulation outcome.

PubMed

Andersen, Simone Nyholm; Broberg, Ole

2015-11-01

Current application of work system simulation in participatory ergonomics (PE) design includes a variety of different simulation media. However, the actual influence of the media attributes on the simulation outcome has received less attention. This study investigates two simulation media: full-scale mock-ups and table-top models. The aim is to compare, how the media attributes of fidelity and affordance influence the ergonomics identification and evaluation in PE design of hospital work systems. The results illustrate, how the full-scale mock-ups' high fidelity of room layout and affordance of tool operation support ergonomics identification and evaluation related to the work system entities space and technologies & tools. The table-top models' high fidelity of function relations and affordance of a helicopter view support ergonomics identification and evaluation related to the entity organization. Furthermore, the study addresses the form of the identified and evaluated conditions, being either identified challenges or tangible design criteria. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

ERMes: Open Source Simplicity for Your E-Resource Management

ERIC Educational Resources Information Center

Doering, William; Chilton, Galadriel

2009-01-01

ERMes, the latest version of electronic resource management system (ERM), is a relational database; content in different tables connects to, and works with, content in other tables. ERMes requires Access 2007 (Windows) or Access 2008 (Mac) to operate as the database utilizes functionality not available in previous versions of Microsoft Access. The…

iTTVis: Interactive Visualization of Table Tennis Data.

PubMed

Wu, Yingcai; Lan, Ji; Shu, Xinhuan; Ji, Chenyang; Zhao, Kejian; Wang, Jiachen; Zhang, Hui

2018-01-01

The rapid development of information technology paved the way for the recording of fine-grained data, such as stroke techniques and stroke placements, during a table tennis match. This data recording creates opportunities to analyze and evaluate matches from new perspectives. Nevertheless, the increasingly complex data poses a significant challenge to make sense of and gain insights into. Analysts usually employ tedious and cumbersome methods which are limited to watching videos and reading statistical tables. However, existing sports visualization methods cannot be applied to visualizing table tennis competitions due to different competition rules and particular data attributes. In this work, we collaborate with data analysts to understand and characterize the sophisticated domain problem of analysis of table tennis data. We propose iTTVis, a novel interactive table tennis visualization system, which to our knowledge, is the first visual analysis system for analyzing and exploring table tennis data. iTTVis provides a holistic visualization of an entire match from three main perspectives, namely, time-oriented, statistical, and tactical analyses. The proposed system with several well-coordinated views not only supports correlation identification through statistics and pattern detection of tactics with a score timeline but also allows cross analysis to gain insights. Data analysts have obtained several new insights by using iTTVis. The effectiveness and usability of the proposed system are demonstrated with four case studies.

Mathematics of Periodic Tables for Benzenoid Hydrocarbons.

PubMed

Dias, Jerry Ray

2007-01-01

The upper and lower bounds for invariants of polyhex systems based on the Harary and Harborth inequalities are studied. It is shown that these invariants are uniquely correlated by the Periodic Table for Benzenoid Hydrocarbons. A modified periodic table for total resonant sextet (TRS) benzenoids based on the invariants of Ds and r(empty) is presented; Ds is the number of disconnections among the empty rings for fused TRS benzenoid hydrocarbons. This work represents a contribution toward deciphering the topological information content of benzenoid formulas.

40 CFR 63.1565 - What are my requirements for organic HAP emissions from catalytic cracking units?

Code of Federal Regulations, 2010 CFR

2010-07-01

... according to the procedures in the plan. (4) The emission limitations and operating limits for organic HAP... work practice standards? You must: (1) Install, operate, and maintain a continuous monitoring system... operating limit in Table 9 of this subpart that applies to you according to the procedures in Table 11 of...

40 CFR 63.1565 - What are my requirements for organic HAP emissions from catalytic cracking units?

Code of Federal Regulations, 2011 CFR

2011-07-01

... according to the procedures in the plan. (4) The emission limitations and operating limits for organic HAP... work practice standards? You must: (1) Install, operate, and maintain a continuous monitoring system... operating limit in Table 9 of this subpart that applies to you according to the procedures in Table 11 of...

All-around viewing display system for group activity on life review therapy

NASA Astrophysics Data System (ADS)

Sakamoto, Kunio; Okumura, Mitsuru

2009-10-01

This paper describes 360 degree viewing display system that can be viewed from any direction. A conventional monitor display is viewed from one direction, i.e., the display has narrow viewing angle and observers cannot view the screen from the opposite side. To solve this problem, we developed the 360 degree viewing display for collaborative tasks on the round table. This developed 360 degree viewing system has a liquid crystal display screen and a 360 degree rotating table by motor. The principle is very simple. The screen of a monitor only rotates at a uniform speed, but the optical techniques are also utilized. Moreover, we have developed a floating 360 degree viewing display that can be viewed from any direction. This new viewing system has a display screen, a rotating table and dual parabolic mirrors. In order to float the only image screen above the table, the rotating mechanism works in the parabolic mirrors. Because the dual parabolic mirrors generate a "mirage" image over the upper mirror, observers can view a floating 2D image on the virtual screen in front of them. Then the observer can view a monitor screen at any position surrounding the round table.

40 CFR Table 4 to Subpart Eeee of... - Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Work Practice Standards 4 Table 4 to..., Table 4 Table 4 to Subpart EEEE of Part 63—Work Practice Standards As stated in § 63.2346, you may elect to comply with one of the work practice standards for existing, reconstructed, or new affected...

40 CFR Table 3 to Subpart IIIii of... - Work Practice Standards-Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks 3 Table 3 to... Standards—Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks... cell back into service until the leaking equipment is repaired. 3. A decomposer or hydrogen system...

40 CFR Table 3 to Subpart IIIii of... - Work Practice Standards-Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks 3 Table 3 to... Standards—Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks... cell back into service until the leaking equipment is repaired. 3. A decomposer or hydrogen system...

40 CFR Table 3 to Subpart IIIii of... - Work Practice Standards-Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks 3 Table 3 to... Standards—Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks... cell back into service until the leaking equipment is repaired. 3. A decomposer or hydrogen system...

40 CFR Table 3 to Subpart IIIii of... - Work Practice Standards-Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks 3 Table 3 to... Standards—Required Actions for Liquid Mercury Spills and Accumulations and Hydrogen and Mercury Vapor Leaks... cell back into service until the leaking equipment is repaired. 3. A decomposer or hydrogen system...

Response of Global Navigation Satellite System receivers to known shaking between 0.2 and 20 Hertz

USGS Publications Warehouse

Langbein, John; Evans, John R.; Blume, Fredrick; Johanson, Ingrid

2014-01-01

Similar to Wang and others (2012), we also examined the GPS displacement records using standard spectral techniques. However, we extended their work by evaluating several models of GNSS receivers using a variety of input frequencies. Because our shake table was limited on acceleration and displacement, we did not attempt to duplicate the high shaking associated with high magnitude earthquakes. However, because our shake table could measure the table displacement, we could directly compare the measured GPS displacements with the true displacements.

[Preliminary study on evaluation system of mental workers strain based on primary and middle school teachers].

PubMed

Lian, Yulong; Liu, Jiwen; Zhang, Chen; Yuan, Fang

2010-09-01

To use primary and middle schools teacher as samples to preliminarily build the mental work stress effect evaluation system, providing the methological platform for the research on the stress effect mechanism and mental workers interference measures. 851 teachers in primary and middle schools were selected with randomly stratified cluster methods. Use ISTA 6.0 and Life Events Evaluation Table to measure the stress factors, and use Work Tension Reaction Questionnaire, Symptom Self-Evaluation Table Questionnaire, and General Happiness Sensing Table to measure psychological stress reaction, blood sugar and blood fat, blood cortical, ACTH, nerve behavior function, for measuring physiological stress reaction. The Comprehensive Working Ability Index Table to measure working ability. And then use the mathematical model to build the mental workers stress effect evaluation system. And apply the simple random sampling method to select 400 environmental protection workers to perform cross effect validation. The model fits relatively well (RMSEA = 0.100, GFI = 0.93, NNFI = 1.00, CFI = 1.00) and conforms with the theory, reflecting the loads of the indice, such as, working stress reaction, psychological stress reaction, physiological stress reaction and working ability, are relatively high. At the same time, the stress reaction of those 4 dimensions can fit the 2-grade factor (stress effect) very well. The physiological stress reaction is negatively correlated (P < 0.05) with the working stress reaction, psychological stress reaction, working ability decrease, while is positively correlated (P < 0.05) with the working stress, psychological stress reaction, physiological stress reaction and working ability decrease. The social support is the protection factor for working stress, psychological stress reaction, physiological stress reaction and working ability decrease (gamma(s) are -0.55, -0.77, 0.73, -0.79, respectively, P < 0.05). While working stress factors, social life stress factors and dangerous individual characters are the risk factors (P < 0.05) for working stress, psychological stress reaction, physiological stress reaction increase and the working ability decrease. The utilization of the environment protection workers further validates this model. It conforms with the theory to evaluate the mental workers stress effects from the 4 dimensions, working stress, psychological stress reaction, physiological stress reaction, and working ability. And these 4 dimensions influence each other, and also are mutually different. The working and social life stress factors influence the stress effects with certain degrees. This evaluation model can tentatively be the methodological basis for the mental workers occupational stress evaluation.

ENGINEERED BARRIER SYSTEM: PHYSICAL AND CHEMICAL ENVIRONMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Jarek

2005-08-29

The purpose of this model report is to describe the evolution of the physical and chemical environmental conditions within the waste emplacement drifts of the repository, including the drip shield and waste package surfaces. The resulting seepage evaporation and gas abstraction models are used in the total system performance assessment for the license application (TSPA-LA) to assess the performance of the engineered barrier system and the waste form. This report develops and documents a set of abstraction-level models that describe the engineered barrier system physical and chemical environment. Where possible, these models use information directly from other reports as input,more » which promotes integration among process models used for TSPA-LA. Specific tasks and activities of modeling the physical and chemical environment are included in ''Technical Work Plan for: Near-Field Environment and Transport In-Drift Geochemistry Model Report Integration'' (BSC 2005 [DIRS 173782], Section 1.2.2). As described in the technical work plan, the development of this report is coordinated with the development of other engineered barrier system reports. To be consistent with other project documents that address features, events, and processes (FEPs), Table 6.14.1 of the current report includes updates to FEP numbers and FEP subjects for two FEPs identified in the technical work plan (TWP) governing this report (BSC 2005 [DIRS 173782]). FEP 2.1.09.06.0A (Reduction-oxidation potential in EBS), as listed in Table 2 of the TWP (BSC 2005 [DIRS 173782]), has been updated in the current report to FEP 2.1.09.06.0B (Reduction-oxidation potential in Drifts; see Table 6.14-1). FEP 2.1.09.07.0A (Reaction kinetics in EBS), as listed in Table 2 of the TWP (BSC 2005 [DIRS 173782]), has been updated in the current report to FEP 2.1.09.07.0B (Reaction kinetics in Drifts; see Table 6.14-1). These deviations from the TWP are justified because they improve integration with FEPs documents. The updates have no impact on the model developed in this report.« less

Comparison of Sedentary Behaviors in Office Workers Using Sit-Stand Tables With and Without Semiautomated Position Changes.

PubMed

Barbieri, Dechristian França; Srinivasan, Divya; Mathiassen, Svend Erik; Oliveira, Ana Beatriz

2017-08-01

We compared usage patterns of two different electronically controlled sit-stand tables during a 2-month intervention period among office workers. Office workers spend most of their working time sitting, which is likely detrimental to health. Although the introduction of sit-stand tables has been suggested as an effective intervention to decrease sitting time, limited evidence is available on usage patterns of sit-stand tables and whether patterns are influenced by table configuration. Twelve workers were provided with standard sit-stand tables (nonautomated table group) and 12 with semiautomated sit-stand tables programmed to change table position according to a preset pattern, if the user agreed to the system-generated prompt (semiautomated table group). Table position was monitored continuously for 2 months after introducing the tables, as a proxy for sit-stand behavior. On average, the table was in a "sit" position for 85% of the workday in both groups; this percentage did not change significantly during the 2-month period. Switches in table position from sit to stand were, however, more frequent in the semiautomated table group than in the nonautomated table group (0.65 vs. 0.29 hr -1 ; p = .001). Introducing a semiautomated sit-stand table appeared to be an attractive alternative to a standard sit-stand table, because it led to more posture variation. A semiautomated sit-stand table may effectively contribute to making postures more variable among office workers and thus aid in alleviating negative health effects of extensive sitting.

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Work Practice Standards for HAP Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Subpt. UUU, Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From...

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Work Practice Standards for HAP Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Subpt. UUU, Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From...

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Work Practice Standards for HAP Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Subpt. UUU, Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From...

40 CFR Table 5 to Subpart Kkkkk of... - Initial Compliance with Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... Limitations and Work Practice Standards 5 Table 5 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 5 Table 5 to Subpart KKKKK of Part 63... table: For each . . . For the following . . . You have demonstrated initial compliance if . . . 1. New...

40 CFR Table 6 to Subpart Kkkkk of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... Limitations and Work Practice Standards 6 Table 6 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 6 Table 6 to Subpart KKKKK of Part 63... to the following table: For each . . . For the following . . . You must demonstrate continuous...

40 CFR Table 5 to Subpart Kkkkk of... - Initial Compliance with Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... Limitations and Work Practice Standards 5 Table 5 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 5 Table 5 to Subpart KKKKK of Part 63... table: For each . . . For the following . . . You have demonstrated initial compliance if . . . 1. New...

40 CFR Table 6 to Subpart Kkkkk of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... Limitations and Work Practice Standards 6 Table 6 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 6 Table 6 to Subpart KKKKK of Part 63... to the following table: For each . . . For the following . . . You must demonstrate continuous...

40 CFR Table 5 to Subpart Kkkkk of... - Initial Compliance with Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... Limitations and Work Practice Standards 5 Table 5 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 5 Table 5 to Subpart KKKKK of Part 63... table: For each . . . For the following . . . You have demonstrated initial compliance if . . . 1. New...

40 CFR Table 6 to Subpart Kkkkk of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... Limitations and Work Practice Standards 6 Table 6 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 6 Table 6 to Subpart KKKKK of Part 63... to the following table: For each . . . For the following . . . You must demonstrate continuous...

40 CFR Table 5 to Subpart Kkkkk of... - Initial Compliance with Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... Limitations and Work Practice Standards 5 Table 5 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 5 Table 5 to Subpart KKKKK of Part 63... table: For each . . . For the following . . . You have demonstrated initial compliance if . . . 1. New...

40 CFR Table 5 to Subpart Kkkkk of... - Initial Compliance with Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... Limitations and Work Practice Standards 5 Table 5 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 5 Table 5 to Subpart KKKKK of Part 63... table: For each . . . For the following . . . You have demonstrated initial compliance if . . . 1. New...

40 CFR Table 6 to Subpart Kkkkk of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... Limitations and Work Practice Standards 6 Table 6 to Subpart KKKKK of Part 63 Protection of Environment... Pollutants for Clay Ceramics Manufacturing Pt. 63, Subpt. KKKKK, Table 6 Table 6 to Subpart KKKKK of Part 63... to the following table: For each . . . For the following . . . You must demonstrate continuous...

Application of Advanced Signal Processing Techniques to Angle of Arrival Estimation in ATC Navigation and Surveillance Systems

DTIC Science & Technology

1982-06-23

Administration Systems Research and Development Service 14, Spseq Aese Ce ’ Washington, D.C. 20591 It. SeppkW•aae metm The work reported in this document was...consider sophisticated signal processing techniques as an alternative method of improving system performanceH Some work in this area has already taken place...demands on the frequency spectrum. As noted in Table 1-1, there has been considerable work on advanced signal processing in the MLS context

Real-Time, General-Purpose, High-Speed Signal Processing Systems for Underwater Research. Proceedings of a Working Level Conference held at Supreme Allied Commander, Atlantic Anti-Submarine Warfare Research Center (SACLANTCEN) on 18-21 September 1979. Part 2. Sessions IV to VI.

DTIC Science & Technology

1979-12-01

ACTIVATED, SYSTEM OPERATION AND TESTING MASCOT PROVIDES: 1. SYSTEM BUILD SOFTWARE COMPILE-TIME CHECKS,a. 2. RUN-TIME SUPERVISOR KERNEL, 3, MONITOR AND...p AD-AOBI 851 SACLANT ASW RESEARCH CENTRE LA SPEZIA 11ITALY) F/B 1711 REAL-TIME, GENERAL-PURPOSE, HIGH-SPEED SIGNAL PROCESSING SYSTEM -- ETC (U) DEC 79...Table of Contents Table of Contents (Cont’d) Page Signal processing language and operating system (w) 23-1 to 23-12 by S. Weinstein A modular signal

40 CFR Table 38 to Subpart Uuu of... - Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 38 Table 38 to Subpart UUU of Part 63 Protection of... Units Pt. 63, Subpt. UUU, Table 38 Table 38 to Subpart UUU of Part 63—Initial Compliance With Work...

40 CFR Table 38 to Subpart Uuu of... - Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 38 Table 38 to Subpart UUU of Part 63 Protection of... Units Pt. 63, Subpt. UUU, Table 38 Table 38 to Subpart UUU of Part 63—Initial Compliance With Work...

40 CFR Table 39 to Subpart Uuu of... - Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 39 Table 39 to Subpart UUU of Part 63 Protection of... Units Pt. 63, Subpt. UUU, Table 39 Table 39 to Subpart UUU of Part 63—Continuous Compliance With Work...

40 CFR Table 39 to Subpart Uuu of... - Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 39 Table 39 to Subpart UUU of Part 63 Protection of... Units Pt. 63, Subpt. UUU, Table 39 Table 39 to Subpart UUU of Part 63—Continuous Compliance With Work...

Method for evaluating compatibility of commercial electromagnetic (EM) microsensor tracking systems with surgical and imaging tables

NASA Astrophysics Data System (ADS)

Nafis, Christopher; Jensen, Vern; von Jako, Ron

2008-03-01

Electromagnetic (EM) tracking systems have been successfully used for Surgical Navigation in ENT, cranial, and spine applications for several years. Catheter sized micro EM sensors have also been used in tightly controlled cardiac mapping and pulmonary applications. EM systems have the benefit over optical navigation systems of not requiring a line-of-sight between devices. Ferrous metals or conductive materials that are transient within the EM working volume may impact tracking performance. Effective methods for detecting and reporting EM field distortions are generally well known. Distortion compensation can be achieved for objects that have a static spatial relationship to a tracking sensor. New commercially available micro EM tracking systems offer opportunities for expanded image-guided navigation procedures. It is important to know and understand how well these systems perform with different surgical tables and ancillary equipment. By their design and intended use, micro EM sensors will be located at the distal tip of tracked devices and therefore be in closer proximity to the tables. Our goal was to define a simple and portable process that could be used to estimate the EM tracker accuracy, and to vet a large number of popular general surgery and imaging tables that are used in the United States and abroad.

Data Management System

NASA Technical Reports Server (NTRS)

1997-01-01

CENTRA 2000 Inc., a wholly owned subsidiary of Auto-trol technology, obtained permission to use software originally developed at Johnson Space Center for the Space Shuttle and early Space Station projects. To support their enormous information-handling needs, a product data management, electronic document management and work-flow system was designed. Initially, just 33 database tables comprised the original software, which was later expanded to about 100 tables. This system, now called CENTRA 2000, is designed for quick implementation and supports the engineering process from preliminary design through release-to-production. CENTRA 2000 can also handle audit histories and provides a means to ensure new information is distributed. The product has 30 production sites worldwide.

Elements of Success: WorkReady Philadelphia Program Year 2011-2012 Report

ERIC Educational Resources Information Center

Philadelphia Youth Network, 2012

2012-01-01

What does it take to deliver WorkReady Philadelphia's high-quality career-connected programming? In short, it's all about the "elements"--those essential components of the system that combine to produce success for young people. This 2011-12 WorkReady report reinforces this theme by using visual aspects of the "Periodic Table of…

40 CFR Table 3 to Subpart Dddd of... - Work Practice Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Work Practice Requirements 3 Table 3 to Subpart DDDD of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Table 3 to Subpart DDDD of Part 63—Work Practice Requirements For the following process units at...

40 CFR Table 4 to Subpart IIIii of... - Work Practice Standards-Requirements for Mercury Liquid Collection

Code of Federal Regulations, 2014 CFR

2014-07-01

... for Mercury Liquid Collection 4 Table 4 to Subpart IIIII of Part 63 Protection of Environment... Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 4 Table 4 to Subpart IIIII of Part 63—Work Practice Standards—Requirements for Mercury Liquid Collection As stated in...

40 CFR Table 4 to Subpart IIIii of... - Work Practice Standards-Requirements for Mercury Liquid Collection

Code of Federal Regulations, 2013 CFR

2013-07-01

... for Mercury Liquid Collection 4 Table 4 to Subpart IIIII of Part 63 Protection of Environment... Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 4 Table 4 to Subpart IIIII of Part 63—Work Practice Standards—Requirements for Mercury Liquid Collection As stated in...

40 CFR Table 4 to Subpart IIIii of... - Work Practice Standards-Requirements for Mercury Liquid Collection

Code of Federal Regulations, 2012 CFR

2012-07-01

... for Mercury Liquid Collection 4 Table 4 to Subpart IIIII of Part 63 Protection of Environment... Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 4 Table 4 to Subpart IIIII of Part 63—Work Practice Standards—Requirements for Mercury Liquid Collection As stated in...

Personnel occupied woven envelope robot power

NASA Technical Reports Server (NTRS)

1987-01-01

The Human Occupied Space Teleoperator (HOST) system currently under development utilizes a flexible tunnel/Stewart table structure to provide crew access to a pressurized manned work station or POD on the space station without extravehicular activity (EVA). The HOST structure facilitates moving a work station to multiple space station locations. The system has applications to orbiter docking, space station assembly, satellite servicing, space station maintenance, and logistics support. The conceptual systems design behind HOST is described in detail.

Forecast model for a water table control system in cranberry production

NASA Astrophysics Data System (ADS)

Racine, Cintia; José Gumiere, Silvio; Paniconi, Claudio; Dupuis, Christian; Lafond, Jonathan; Scudeler, Carlotta; Camporese, Matteo

2017-04-01

Water table control is gaining popularity in cranberry production. Cranberry plants require specific soil moisture conditions to enhance crop yields. In fact, water table control systems installed in the fields allow the plants to respond efficiently to the daily demand for evapotranspiration by capillarity rise and also regulate the soil water excess in drainage conditions. The scope of this study is to develop a forecast hydrological model at the field scale, able to simulate water level for water table control operations. In this work, the finite element CATHY (CATchment Hydrology) model associated with sequential data assimilation with an ensemble Kalman filter (EnKF) method will be used to simulated the soil water dynamics and perform model calibration in real-time. The study is conducted in cranberry fields located in Québec, Canada. During the last five years, these fields were extensive characterized regarding hydrological, pedological, and geological processes. Data collected from LIDAR and Ground Penetrating Radar (GPR) surveys and in-situ soil sampling have been used to define the domain geometry and initial soil properties. First results are promising and in agreement the in-situ water table measurements.

Two Related Parametric Integrals

ERIC Educational Resources Information Center

Dana-Picard, T.

2007-01-01

Two related sequences of definite integrals are considered. By mixing hand-work, computer algebra system assistance and websurfing, fine connections can be studied between integrals and a couple of interesting sequences of integers. (Contains 4 tables.)

Designing For Human Presence in Space: An Introduction to Environmental Control and Life Support Systems (ECLSS)

NASA Technical Reports Server (NTRS)

Wieland, P. O.

2005-01-01

Human exploration and utilization of space requires habitats to provide appropriate conditions for working and living. These conditions are provided by environmental control and life support systems (ECLSS) that ensure appropriate atmosphere composition, pressure, and temperature; manage and distribute water, process waste matter, provide fire detection and suppression; and other functions as necessary. The tables in appendix I of NASA RP 1324 "Designing for Human Presence in Space" summarize the life support functions and processes used onboard U.S. and U.S.S.R/Russian space habitats. These tables have been updated to include information on thermal control methods and to provide additional information on the ECLS systems.

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2011 CFR

2011-07-01

... Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL... Refineries: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From Bypass Lines...

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2010 CFR

2010-07-01

... Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL... Refineries: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From Bypass Lines...

Intraoperative computed tomography with integrated navigation system in a multidisciplinary operating suite.

PubMed

Uhl, Eberhard; Zausinger, Stefan; Morhard, Dominik; Heigl, Thomas; Scheder, Benjamin; Rachinger, Walter; Schichor, Christian; Tonn, Jörg-Christian

2009-05-01

We report our preliminary experience in a prospective series of patients with regard to feasibility, work flow, and image quality using a multislice computed tomographic (CT) scanner combined with a frameless neuronavigation system (NNS). A sliding gantry 40-slice CT scanner was installed in a preexisting operating room. The scanner was connected to a frameless infrared-based NNS. Image data was transferred directly from the scanner into the navigation system. This allowed updating of the NNS during surgery by automated image registration based on the position of the gantry. Intraoperative CT angiography was possible. The patient was positioned on a radiolucent operating table that fits within the bore of the gantry. During image acquisition, the gantry moved over the patient. This table allowed all positions and movements like any normal operating table without compromising the positioning of the patient. For cranial surgery, a carbon-made radiolucent head clamp was fixed to the table. Experience with the first 230 patients confirms the feasibility of intraoperative CT scanning (136 patients with intracranial pathology, 94 patients with spinal lesions). After a specific work flow, interruption of surgery for intraoperative scanning can be limited to 10 to 15 minutes in cranial surgery and to 9 minutes in spinal surgery. Intraoperative imaging changed the course of surgery in 16 of the 230 cases either because control CT scans showed suboptimal screw position (17 of 307 screws, with 9 in 7 patients requiring correction) or that tumor resection was insufficient (9 cases). Intraoperative CT angiography has been performed in 7 cases so far with good image quality to determine residual flow in an aneurysm. Image quality was excellent in spinal and cranial base surgery. The system can be installed in a preexisting operating environment without the need for special surgical instruments. It increases the safety of the patient and the surgeon without necessitating a change in the existing surgical protocol and work flow. Imaging and updating of the NNS can be performed at any time during surgery with very limited time and modification of the surgical setup. Multidisciplinary use increases utilization of the system and thus improves the cost-efficiency relationship.

40 CFR Table 39 to Subpart Uuu of... - Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 39 Table 39 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 39 Table 39 to Subpart UUU of Part 63—Continuous...

40 CFR Table 38 to Subpart Uuu of... - Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 38 Table 38 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 38 Table 38 to Subpart UUU of Part 63—Initial Compliance...

40 CFR Table 38 to Subpart Uuu of... - Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 38 Table 38 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 38 Table 38 to Subpart UUU of Part 63—Initial Compliance...

40 CFR Table 39 to Subpart Uuu of... - Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 39 Table 39 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 39 Table 39 to Subpart UUU of Part 63—Continuous...

40 CFR Table 39 to Subpart Uuu of... - Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Continuous Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 39 Table 39 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 39 Table 39 to Subpart UUU of Part 63—Continuous...

40 CFR Table 38 to Subpart Uuu of... - Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Initial Compliance With Work Practice Standards for HAP Emissions From Bypass Lines 38 Table 38 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 38 Table 38 to Subpart UUU of Part 63—Initial Compliance...

Multiple Target Tracking in a Wide-Field-of-View Camera System

DTIC Science & Technology

1990-01-01

assembly is mounted on a Contraves alt-azi axis table with a pointing accuracy of < 2 Urad. * Work performed under the auspices of the U.S. Department of... Contraves SUN 3 CCD DR11W VME EITHERNET SUN 3 !3T 3 RS170 Video 1 Video ^mglifier^ I WWV Clock VCR Datacube u Monitor Monitor UL...displaying processed images with overlay from the Datacube. We control the Contraves table using a GPIB interface on the SUN. GPIB also interfaces a

Plutonium immobilization can loading FY99 component test report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kriikku, E.

2000-06-01

This report summarizes FY99 Can Loading work completed for the Plutonium Immobilization Project and it includes details about the Helium hood, cold pour cans, Can Loading robot, vision system, magnetically coupled ray cart and lifts, system integration, Can Loading glovebox layout, and an FY99 cost table.

Specific modes of vibratory technological machines: mathematical models, peculiarities of interaction of system elements

NASA Astrophysics Data System (ADS)

Eliseev, A. V.; Sitov, I. S.; Eliseev, S. V.

2018-03-01

The methodological basis of constructing mathematical models of vibratory technological machines is developed in the article. An approach is proposed that makes it possible to introduce a vibration table in a specific mode that provides conditions for the dynamic damping of oscillations for the zone of placement of a vibration exciter while providing specified vibration parameters in the working zone of the vibration table. The aim of the work is to develop methods of mathematical modeling, oriented to technological processes with long cycles. The technologies of structural mathematical modeling are used with structural schemes, transfer functions and amplitude-frequency characteristics. The concept of the work is to test the possibilities of combining the conditions for reducing loads with working components of a vibration exciter while simultaneously maintaining sufficiently wide limits in variating the parameters of the vibrational field.

COSPAR Round Table on `How can GEO and COSPAR scientific community work together?'

NASA Astrophysics Data System (ADS)

Gobron, Nadine; Ollier, Gilles

The Group on Earth Observations is coordinating efforts to build a Global Earth Observation System of Systems, or GEOSS. GEO is a voluntary partnership of governments and inter-national organizations. It provides a framework within which these partners can develop new projects and coordinate their strategies and investments. The Science and Technology Commit-tee of GEO is working to strengthen this role by encouraging the wider scientific and technology community to participate as contributors to and benefactors of a sustained GEOSS. The proposed round table aims at discussing how are scientists and GEO currently working together, using specific examples and how do space agencies or data providers contribute to GEO? Round table participants are welcome to present their own vision on future actions to improve, if necessary, the relations between contributors and GEO. Meeting participants will also be offered the opportunity to intervene and ask questions to the panel. Moderators: • Dr. Nadine Gobron -EC-JRC -Chair of Commission A • Gilles Ollier -DG Research Participants: • Prof. José Achache -Director of GEO • Prof. Maurice Bonnet -President of COSPAR • Dr. Tamatsu Igarashi -JAXA EORC Manager • Dr. Stuart Minchin (CSIRO and member of GEO STC) TBC • Prof. Berrien Moore -Executive Director of Climate Central • Dr. Diane E. Wickland -NASA Headquarters • Dr. Stephen Briggs -ESA (TBC)

Multiobjective Collaborative Optimization of Systems of Systems

DTIC Science & Technology

2005-06-01

K: HSC MODEL AND OPTIMIZATION DESCRIPTION ................................................ 157 APPENDIX L: HSC OPTIMIZATION CODE...7 0 Table 6. System Variables of FPF Data Set Showing Minimal HSC Impact on...App.E, F) Data Analysis Front ITS Model (App. I, J) Chap.] 1 ConclusionsSHSC Model (App. K, L) Cot[& HSC Model (App. M, NV) MoeJ Future Work Figure

Reducing the risk of injury from table saw use: the potential benefits and costs of automatic protection.

PubMed

Graham, John D; Chang, Joice

2015-02-01

The use of table saws in the United States is associated with approximately 28,000 emergency department (ED) visits and 2,000 cases of finger amputation per year. This article provides a quantitative estimate of the economic benefits of automatic protection systems that could be designed into new table saw products. Benefits are defined as reduced health-care costs, enhanced production at work, and diminished pain and suffering. The present value of the benefits of automatic protection over the life of the table saw are interpreted as the switch-point cost value, the maximum investment in automatic protection that can be justified by benefit-cost comparison. Using two alternative methods for monetizing pain and suffering, the study finds switch-point cost values of $753 and $561 per saw. These point estimates are sensitive to the values of inputs, especially the average cost of injury. The various switch-point cost values are substantially higher than rough estimates of the incremental cost of automatic protection systems. Uncertainties and future research needs are discussed. © 2014 Society for Risk Analysis.

System Control for the Transitional DCS.

DTIC Science & Technology

1979-07-01

ELEMENT. PROJI Honeywell System and Research Center AREA & WORK UNIT NUMBE Aerospace and Defense Group 2700 Ridgway Parkway, Minneapolis,MN 55413 It1...performance monitoring and stress isolation system for the terrestrial transmission system. The satellite system is assumed to be under the control of its...the routing tables could be in a failed condition while some other route, although less efficient, is still functioning. The recommended adaptive

Where this occurs: Ground Water and Drinking Water

EPA Pesticide Factsheets

As ground water works its way through the soil, it can pick up excess nutrients and transport them to the water table. When polluted groundwater reaches drinking water systems it can pose serious public health threats.

Automatic system for computer program documentation

NASA Technical Reports Server (NTRS)

Simmons, D. B.; Elliott, R. W.; Arseven, S.; Colunga, D.

1972-01-01

Work done on a project to design an automatic system for computer program documentation aids was made to determine what existing programs could be used effectively to document computer programs. Results of the study are included in the form of an extensive bibliography and working papers on appropriate operating systems, text editors, program editors, data structures, standards, decision tables, flowchart systems, and proprietary documentation aids. The preliminary design for an automated documentation system is also included. An actual program has been documented in detail to demonstrate the types of output that can be produced by the proposed system.

An embedded real-time red peach detection system based on an OV7670 camera, ARM cortex-M4 processor and 3D look-up tables.

PubMed

Teixidó, Mercè; Font, Davinia; Pallejà, Tomàs; Tresanchez, Marcel; Nogués, Miquel; Palacín, Jordi

2012-10-22

This work proposes the development of an embedded real-time fruit detection system for future automatic fruit harvesting. The proposed embedded system is based on an ARM Cortex-M4 (STM32F407VGT6) processor and an Omnivision OV7670 color camera. The future goal of this embedded vision system will be to control a robotized arm to automatically select and pick some fruit directly from the tree. The complete embedded system has been designed to be placed directly in the gripper tool of the future robotized harvesting arm. The embedded system will be able to perform real-time fruit detection and tracking by using a three-dimensional look-up-table (LUT) defined in the RGB color space and optimized for fruit picking. Additionally, two different methodologies for creating optimized 3D LUTs based on existing linear color models and fruit histograms were implemented in this work and compared for the case of red peaches. The resulting system is able to acquire general and zoomed orchard images and to update the relative tracking information of a red peach in the tree ten times per second.

An Embedded Real-Time Red Peach Detection System Based on an OV7670 Camera, ARM Cortex-M4 Processor and 3D Look-Up Tables

PubMed Central

Teixidó, Mercè; Font, Davinia; Pallejà, Tomàs; Tresanchez, Marcel; Nogués, Miquel; Palacín, Jordi

2012-01-01

This work proposes the development of an embedded real-time fruit detection system for future automatic fruit harvesting. The proposed embedded system is based on an ARM Cortex-M4 (STM32F407VGT6) processor and an Omnivision OV7670 color camera. The future goal of this embedded vision system will be to control a robotized arm to automatically select and pick some fruit directly from the tree. The complete embedded system has been designed to be placed directly in the gripper tool of the future robotized harvesting arm. The embedded system will be able to perform real-time fruit detection and tracking by using a three-dimensional look-up-table (LUT) defined in the RGB color space and optimized for fruit picking. Additionally, two different methodologies for creating optimized 3D LUTs based on existing linear color models and fruit histograms were implemented in this work and compared for the case of red peaches. The resulting system is able to acquire general and zoomed orchard images and to update the relative tracking information of a red peach in the tree ten times per second. PMID:23202040

Paper and Other Web Coating Maximum Achievable Control Technology (MACT): Work Practice, Testing, Monitoring, Recordkeeping, and Reporting Summary Table

EPA Pesticide Factsheets

This April 2004 document is a table that details the various requirements of the Paper and Other Web Coating NESHAP, broken down by category. This table covers applicability, recordkeeping, emission limits, work practice standards, and other requirements

Disposal of Unused Medicines: What You Should Know

MedlinePlus

... any potential risk to human health or the environment that may come from disposal by flushing. FDA continues to work with and encourage manufacturers of these medicines to develop alternative, safe disposal systems. Back to Table of Contents How ...

Hip joint kinetics in the table tennis topspin forehand: relationship to racket velocity.

PubMed

Iino, Yoichi

2018-04-01

The purpose of this study was to determine hip joint kinetics during a table tennis topspin forehand, and to investigate the relationship between the relevant kinematic and kinetic variables and the racket horizontal and vertical velocities at ball impact. Eighteen male advanced table tennis players hit cross-court topspin forehands against backspin balls. The hip joint torque and force components around the pelvis coordinate system were determined using inverse dynamics. Furthermore, the work done on the pelvis by these components was also determined. The peak pelvis axial rotation velocity and the work done by the playing side hip pelvis axial rotation torque were positively related to the racket horizontal velocity at impact. The sum of the work done on the pelvis by the backward tilt torques and the upward joint forces was positively related to the racket vertical velocity at impact. The results suggest that the playing side hip pelvis axial rotation torque exertion is important for acquiring a high racket horizontal velocity at impact. The pelvis backward tilt torques and upward joint forces at both hip joints collectively contribute to the generation of the racket vertical velocity, and the mechanism for acquiring the vertical velocity may vary among players.

Touchscreen everywhere: on transferring a normal planar surface to a touch-sensitive display.

PubMed

Dai, Jingwen; Chung, Chi-Kit Ronald

2014-08-01

We address how a human-computer interface with small device size, large display, and touch-input facility can be made possible by a mere projector and camera. The realization is through the use of a properly embedded structured light sensing scheme that enables a regular light-colored table surface to serve the dual roles of both a projection screen and a touch-sensitive display surface. A random binary pattern is employed to code structured light in pixel accuracy, which is embedded into the regular projection display in a way that the user perceives only regular display but not the structured pattern hidden in the display. With the projection display on the table surface being imaged by a camera, the observed image data, plus the known projection content, can work together to probe the 3-D workspace immediately above the table surface, like deciding if there is a finger present and if the finger touches the table surface, and if so, at what position on the table surface the contact is made. All the decisions hinge upon a careful calibration of the projector-camera-table surface system, intelligent segmentation of the hand in the image data, and exploitation of the homography mapping existing between the projector's display panel and the camera's image plane. Extensive experimentation including evaluation of the display quality, hand segmentation accuracy, touch detection accuracy, trajectory tracking accuracy, multitouch capability and system efficiency are shown to illustrate the feasibility of the proposed realization.

Bridging Ground Validation and Algorithms: Using Scattering and Integral Tables to Incorporate Observed DSD Correlations into Satellite Algorithms

NASA Astrophysics Data System (ADS)

Williams, C. R.

2012-12-01

The NASA Global Precipitation Mission (GPM) raindrop size distribution (DSD) Working Group is composed of NASA PMM Science Team Members and is charged to "investigate the correlations between DSD parameters using Ground Validation (GV) data sets that support, or guide, the assumptions used in satellite retrieval algorithms." Correlations between DSD parameters can be used to constrain the unknowns and reduce the degrees-of-freedom in under-constrained satellite algorithms. Over the past two years, the GPM DSD Working Group has analyzed GV data and has found correlations between the mass-weighted mean raindrop diameter (Dm) and the mass distribution standard deviation (Sm) that follows a power-law relationship. This Dm-Sm power-law relationship appears to be robust and has been observed in surface disdrometer and vertically pointing radar observations. One benefit of a Dm-Sm power-law relationship is that a three parameter DSD can be modeled with just two parameters: Dm and Nw that determines the DSD amplitude. In order to incorporate observed DSD correlations into satellite algorithms, the GPM DSD Working Group is developing scattering and integral tables that can be used by satellite algorithms. Scattering tables describe the interaction of electromagnetic waves on individual particles to generate cross sections of backscattering, extinction, and scattering. Scattering tables are independent of the distribution of particles. Integral tables combine scattering table outputs with DSD parameters and DSD correlations to generate integrated normalized reflectivity, attenuation, scattering, emission, and asymmetry coefficients. Integral tables contain both frequency dependent scattering properties and cloud microphysics. The GPM DSD Working Group has developed scattering tables for raindrops at both Dual Precipitation Radar (DPR) frequencies and at all GMI radiometer frequencies less than 100 GHz. Scattering tables include Mie and T-matrix scattering with H- and V-polarization at the instrument view angles of nadir to 17 degrees (for DPR) and 48 & 53 degrees off nadir (for GMI). The GPM DSD Working Group is generating integral tables with GV observed DSD correlations and is performing sensitivity and verification tests. One advantage of keeping scattering tables separate from integral tables is that research can progress on the electromagnetic scattering of particles independent of cloud microphysics research. Another advantage of keeping the tables separate is that multiple scattering tables will be needed for frozen precipitation. Scattering tables are being developed for individual frozen particles based on habit, density and operating frequency. And a third advantage of keeping scattering and integral tables separate is that this framework provides an opportunity to communicate GV findings about DSD correlations into integral tables, and thus, into satellite algorithms.

Focus collimator press for a collimator for gamma ray cameras

DOE Office of Scientific and Technical Information (OSTI.GOV)

York, R.N.; York, D.L.

A focus collimator press for collimators for gamma ray cameras is described comprising a pivot arm of fixed length mounted on a travelling pivot which is movable in the plane of a spaced apart work table surface in a direction toward and away from the work table. A press plate is carried at the opposite end of the fixed length pivot arm, and is maintained in registration with the same portion of the work table for pressing engagement with each undulating radiation opaque strip as it is added to the top of a collimator stack in process by movement ofmore » the travelling pivot inward toward the work table. This enables the press plate to maintain its relative position above the collimator stack and at the same time the angle of the press plate changes, becoming less acute in relation to the work table as the travelling pivot motes inwardly toward the work table. The fixed length of the pivot arm is substantially equal to the focal point of the converging apertures formed by each pair of undulating strips stacked together. Thus, the focal point of each aperture row falls substantially on the axis of the travelling pivot, and since it moves in the plane of the work table surface the focal point of each aperture row is directed to lie in the same common plane. When one of two collimator stacks made in this way is rotated 180 degrees and the two bonded together along their respective first strips, all focal points of every aperture row lie on the central axis of the completed collimator.« less

Singular spectrum and singular entropy used in signal processing of NC table

NASA Astrophysics Data System (ADS)

Wang, Linhong; He, Yiwen

2011-12-01

NC (numerical control) table is a complex dynamic system. The dynamic characteristics caused by backlash, friction and elastic deformation among each component are so complex that they have become the bottleneck of enhancing the positioning accuracy, tracking accuracy and dynamic behavior of NC table. This paper collects vibration acceleration signals from NC table, analyzes the signals with SVD (singular value decomposition) method, acquires the singular spectrum and calculates the singular entropy of the signals. The signal characteristics and their regulations of NC table are revealed via the characteristic quantities such as singular spectrum, singular entropy etc. The steep degrees of singular spectrums can be used to discriminate complex degrees of signals. The results show that the signals in direction of driving axes are the simplest and the signals in perpendicular direction are the most complex. The singular entropy values can be used to study the indetermination of signals. The results show that the signals of NC table are not simple signal nor white noise, the entropy values in direction of driving axe are lower, the entropy values increase along with the increment of driving speed and the entropy values at the abnormal working conditions such as resonance or creeping etc decrease obviously.

Form-class volume tables for estimating board-foot content of northern conifers

Treesearch

C. Allen Bickford

1951-01-01

The timber cruiser counts volume tables among his most important working tools. He wants - if he can get them - tables that are simple, easy to use, and accurate. Before using a volume table in a new situation, the careful cruiser will check it by comparing table volumes with actual volumes.

Novel Hybrid Operating Table for Neuroendovascular Treatment.

PubMed

Jong-Hyun, Park; Jonghyeon, Mun; Dong-Seung, Shin; Bum-Tae, Kim

2017-03-25

The integration of interventional and surgical techniques is requiring the development of a new working environment equipped for the needs of an interdisciplinary neurovascular team. However, conventional surgical and interventional tables have only a limited ability to provide for these needs. We have developed a concept mobile hybrid operating table that provides the ability for such a team to conduct both endovascular and surgical procedures in a single session. We developed methods that provide surgeons with angiography-guided surgery techniques for use in a conventional operating room environment. In order to design a convenient device ideal for practical use, we consulted with mechanical engineers. The mobile hybrid operating table consists of two modules: a floating tabletop and a mobile module. In brief, the basic principle of the mobile hybrid operating table is as follows: firstly, the length of the mobile hybrid operating table is longer than that of a conventional surgical table and yet shorter than a conventional interventional table. It was designed with the goal of exhaustively meeting the intensive requirements of both endovascular and surgical procedures. Its mobile module allows for the floating tabletop to be moved quickly and precisely. It is important that during a procedure, a patient can be moved without being repositioned, particularly with a catheter in situ. Secondly, a slim-profile headrest facilitates the mounting of a radiolucent head cramp system for cranial stabilization and fixation. We have introduced a novel invention, a mobile hybrid operating table for use in an operating suite.

40 CFR Table 10 to Subpart Eeee of... - Continuous Compliance With Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... liquids, operate a vapor balancing system. i. Monitoring each potential source of vapor leakage in the... requirements of 40 CFR part 63, subpart TT, UU, or H. i. Carrying out a leak detection and repair program in... relief devices, monitoring each potential source of vapor leakage in the system, including, but not...

Systems Analysis of GPS Electrical Power System Redesign

DTIC Science & Technology

1995-12-01

Table 8 - System Efficiencies & Multipliers for Solar Direct Model (12:102; 15:864) Component Efficiency AMTEC 0.180 Receiver and Thermal Energy Storage...and low temperatures of the working fluid. Extreme high and low temperatures provide a greater efficiency , but require extensive thermal control and...direct conversion category. The Alkali Metal Thermal -to-Electric Converter ( AMTEC ) shows mass and cost savings due to efficiencies significantly higher

[Electronic poison information management system].

PubMed

Kabata, Piotr; Waldman, Wojciech; Kaletha, Krystian; Sein Anand, Jacek

2013-01-01

We describe deployment of electronic toxicological information database in poison control center of Pomeranian Center of Toxicology. System was based on Google Apps technology, by Google Inc., using electronic, web-based forms and data tables. During first 6 months from system deployment, we used it to archive 1471 poisoning cases, prepare monthly poisoning reports and facilitate statistical analysis of data. Electronic database usage made Poison Center work much easier.

Modular Fixturing System

NASA Technical Reports Server (NTRS)

Littell, Justin Anderson (Inventor); Street, Jon P. (Inventor)

2017-01-01

The modular fixturing system of the present invention is modular, reusable and capable of significant customization, both in terms of system radius and system height, allowing it to be arranged and rearranged in numerous unique configurations. The system includes multiple modular stanchions having stanchion shafts and stanchion feet that removably attach to apertures in a table. Angle brackets attached to the modular stanchions support shelves. These shelves in turn provide support to work pieces during fabrication processes such as welding.

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 2 Table 2 to Subpart IIIII of Part 63—Work... must . . . 1. Each vent hose on each mercury cell Half day A leaking vent hose Take action immediately... mercury seal pot stopper securely in place. 6. Cell room floors Month Cracks, spalling, or other...

Army Information Operations Officer Needs Analysis Report

DTIC Science & Technology

2016-03-01

21 TABLE 3 . IO OFFICER SURVEY RESULTS FOR FREQUENCY , CRITICALITY, AND QC PREPAREDNESS TO WORK WITH THE IRCS...have to learn everything. . . . Let commanders understand this is what I bring to the table for you because when he understands that in garrison...neither disagree 28 Table 3 IO Officer Survey Results for Frequency , Criticality, and QC Preparedness to Work with the IRCs Information

Work-rate-guided exercise testing in patients with incomplete spinal cord injury using a robotics-assisted tilt-table.

PubMed

Laubacher, Marco; Perret, Claudio; Hunt, Kenneth J

2015-01-01

Robotics-assisted tilt-table (RTT) technology allows neurological rehabilitation therapy to be started early thus alleviating some secondary complications of prolonged bed rest. This study assessed the feasibility of a novel work-rate-guided RTT approach for cardiopulmonary training and assessment in patients with incomplete spinal cord injury (iSCI). Three representative subjects with iSCI at three distinct stages of primary rehabilitation completed an incremental exercise test (IET) and a constant load test (CLT) on a RTT augmented with integrated leg-force and position measurement and visual work rate feedback. Feasibility assessment focused on: (i) implementation, (ii) limited efficacy testing, (iii) acceptability. (i) All subjects were able follow the work rate target profile by adapting their volitional leg effort. (ii) During the IETs, peak oxygen uptake above rest was 304, 467 and 1378 ml/min and peak heart rate (HR) was 46, 32 and 65 beats/min above rest (subjects A, B and C, respectively). During the CLTs, steady-state oxygen uptake increased by 42%, 38% and 162% and HR by 12%, 20% and 29%. (iii) All exercise tests were tolerated well. The novel work-rate guided RTT intervention is deemed feasible for cardiopulmonary training and assessment in patients with iSCI: substantial cardiopulmonary responses were observed and the approach was found to be tolerable and implementable. Implications for Rehabilitation Work-rate guided robotics-assisted tilt-table technology is deemed feasible for cardiopulmonary assessment and training in patients with incomplete spinal cord injury. Robotics-assisted tilt-tables might be a good way to start with an active rehabilitation as early as possible after a spinal cord injury. During training with robotics-assisted devices the active participation of the patients is crucial to strain the cardiopulmonary system and hence gain from the training.

Relative-Motion Sensors and Actuators for Two Optical Tables

NASA Technical Reports Server (NTRS)

Gursel, Yekta; McKenney, Elizabeth

2004-01-01

Optoelectronic sensors and magnetic actuators have been developed as parts of a system for controlling the relative position and attitude of two massive optical tables that float on separate standard air suspensions that attenuate ground vibrations. In the specific application for which these sensors and actuators were developed, one of the optical tables holds an optical system that mimics distant stars, while the other optical table holds a test article that simulates a spaceborne stellar interferometer that would be used to observe the stars. The control system is designed to suppress relative motion of the tables or, on demand, to impose controlled relative motion between the tables. The control system includes a sensor system that detects relative motion of the tables in six independent degrees of freedom and a drive system that can apply force to the star-simulator table in the six degrees of freedom. The sensor system includes (1) a set of laser heterodyne gauges and (2) a set of four diode lasers on the star-simulator table, each aimed at one of four quadrant photodiodes at nominal corresponding positions on the test-article table. The heterodyne gauges are used to measure relative displacements along the x axis.

40 CFR Table 8 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Heat Exchange Systems

Code of Federal Regulations, 2011 CFR

2011-07-01

... Requirements for Heat Exchange Systems 8 Table 8 to Subpart VVVVVV of Part 63 Protection of Environment... Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 8 Table 8 to Subpart VVVVVV....11499, you must comply with the requirements for heat exchange systems as shown in the following table...

40 CFR Table 8 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Heat Exchange Systems

Code of Federal Regulations, 2013 CFR

2013-07-01

... Requirements for Heat Exchange Systems 8 Table 8 to Subpart VVVVVV of Part 63 Protection of Environment... Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 8 Table 8 to Subpart VVVVVV....11499, you must comply with the requirements for heat exchange systems as shown in the following table...

40 CFR Table 8 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Heat Exchange Systems

Code of Federal Regulations, 2012 CFR

2012-07-01

... Requirements for Heat Exchange Systems 8 Table 8 to Subpart VVVVVV of Part 63 Protection of Environment... Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 8 Table 8 to Subpart VVVVVV....11499, you must comply with the requirements for heat exchange systems as shown in the following table...

40 CFR Table 8 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Heat Exchange Systems

Code of Federal Regulations, 2014 CFR

2014-07-01

... Requirements for Heat Exchange Systems 8 Table 8 to Subpart VVVVVV of Part 63 Protection of Environment... Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 8 Table 8 to Subpart VVVVVV....11499, you must comply with the requirements for heat exchange systems as shown in the following table...

40 CFR Table 8 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Heat Exchange Systems

Code of Federal Regulations, 2010 CFR

2010-07-01

... Requirements for Heat Exchange Systems 8 Table 8 to Subpart VVVVVV of Part 63 Protection of Environment... Pollutants for Chemical Manufacturing Area Sources Pt. 63, Subpt. VVVVVV, Table 8 Table 8 to Subpart VVVVVV....11499, you must comply with the requirements for heat exchange systems as shown in the following table...

Experiences with Interactive Multi-touch Tables

NASA Astrophysics Data System (ADS)

Fikkert, Wim; Hakvoort, Michiel; van der Vet, Paul; Nijholt, Anton

Interactive multi-touch tables can be a powerful means of communication for collaborative work as well as an engaging environment for competition. Through enticing gameplay we have evaluated user experience on competitive gameplay, collaborative work and musical expression. In addition, we report on our extensive experiences with two types of interactive multi-touch tables and we introduce a software framework that abstracts from their technical differences.

Proposal of Network-Based Multilingual Space Dictionary Database System

NASA Astrophysics Data System (ADS)

Yoshimitsu, T.; Hashimoto, T.; Ninomiya, K.

2002-01-01

The International Academy of Astronautics (IAA) is now constructing a multilingual dictionary database system of space-friendly terms. The database consists of a lexicon and dictionaries of multiple languages. The lexicon is a table which relates corresponding terminology in different languages. Each language has a dictionary which contains terms and their definitions. The database assumes the use on the internet. Updating and searching the terms and definitions are conducted via the network. Maintaining the database is conducted by the international cooperation. A new word arises day by day, thus to easily input new words and their definitions to the database is required for the longstanding success of the system. The main key of the database is an English term which is approved at the table held once or twice with the working group members. Each language has at lease one working group member who is responsible of assigning the corresponding term and the definition of the term of his/her native language. Inputting and updating terms and their definitions can be conducted via the internet from the office of each member which may be located at his/her native country. The system is constructed by freely distributed database server program working on the Linux operating system, which will be installed at the head office of IAA. Once it is installed, it will be open to all IAA members who can search the terms via the internet. Currently the authors are constructing the prototype system which is described in this paper.

40 CFR Table 1 to Subpart Uuuu of... - Emission Limits and Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... least once per month as specified in § 63.148(f)(2)). 12. heat exchanger system that cools process equipment or materials in the process unit each existing or new affected source monitor and repair the heat exchanger system according to § 63.104(a) through (e), except that references to “chemical manufacturing...

40 CFR Table 1 to Subpart Uuuu of... - Emission Limits and Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... least once per month as specified in § 63.148(f)(2)). 12. heat exchanger system that cools process equipment or materials in the process unit each existing or new affected source monitor and repair the heat exchanger system according to § 63.104(a) through (e), except that references to “chemical manufacturing...

40 CFR Table 1 to Subpart Uuuu of... - Emission Limits and Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... least once per month as specified in § 63.148(f)(2)). 12. heat exchanger system that cools process equipment or materials in the process unit each existing or new affected source monitor and repair the heat exchanger system according to § 63.104(a) through (e), except that references to “chemical manufacturing...

Bending of I-beam with the transvers shear effect included - FEM calculated

NASA Astrophysics Data System (ADS)

Grygorowicz, Magdalena; Lewiński, Jerzy

2016-06-01

The paper is devoted to three-point bending of an I-beam with include of transvers shear effect. Numerical calculations were conducted independently with the use of the SolidWorks system and the multi-purpose software package ANSYS The results of FEM study conducted with the use of two systems were compared and presented in tables and figures.

Bending of I-beam with the transvers shear effect included – FEM calculated

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grygorowicz, Magdalena; Lewiński, Jerzy

2016-06-08

The paper is devoted to three-point bending of an I-beam with include of transvers shear effect. Numerical calculations were conducted independently with the use of the SolidWorks system and the multi-purpose software package ANSYS The results of FEM study conducted with the use of two systems were compared and presented in tables and figures.

40 CFR Table 6 to Subpart Kkkkk of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... or DLS/FF i. If you use a bag leak detection system, initiating corrective action within 1 hour of a bag leak detection system alarm and completing corrective actions in accordance with your OM&M plan... established during the performance test; and iv. If chemicals are added to the scrubber water, collecting the...

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Code of Federal Regulations, 2012 CFR

2012-07-01

... each . . . You must . . . 1. Group 1 transfer rack a. Reduce emissions of total organic HAP by ≥98... through a closed-vent system to any combination of control devices (except a flare); or b. Reduce....982(d) and the requirements referenced therein; or d. Use a vapor balancing system designed and...

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Code of Federal Regulations, 2014 CFR

2014-07-01

... each . . . You must . . . 1. Group 1 transfer rack a. Reduce emissions of total organic HAP by ≥98... through a closed-vent system to any combination of control devices (except a flare); or b. Reduce....982(d) and the requirements referenced therein; or d. Use a vapor balancing system designed and...

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Code of Federal Regulations, 2010 CFR

2010-07-01

... each . . . You must . . . 1. Group 1 transfer rack a. Reduce emissions of total organic HAP by ≥98... through a closed-vent system to any combination of control devices (except a flare); or b. Reduce....982(d) and the requirements referenced therein; or d. Use a vapor balancing system designed and...

40 CFR Table 1 to Subpart Uuuu of... - Emission Limits and Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... least once per month as specified in § 63.148(f)(2)). 12. heat exchanger system that cools process equipment or materials in the process unit each existing or new affected source monitor and repair the heat exchanger system according to § 63.104(a) through (e), except that references to “chemical manufacturing...

Experimental/analytical approaches to modeling, calibrating and optimizing shaking table dynamics for structural dynamic applications

NASA Astrophysics Data System (ADS)

Trombetti, Tomaso

This thesis presents an Experimental/Analytical approach to modeling and calibrating shaking tables for structural dynamic applications. This approach was successfully applied to the shaking table recently built in the structural laboratory of the Civil Engineering Department at Rice University. This shaking table is capable of reproducing model earthquake ground motions with a peak acceleration of 6 g's, a peak velocity of 40 inches per second, and a peak displacement of 3 inches, for a maximum payload of 1500 pounds. It has a frequency bandwidth of approximately 70 Hz and is designed to test structural specimens up to 1/5 scale. The rail/table system is mounted on a reaction mass of about 70,000 pounds consisting of three 12 ft x 12 ft x 1 ft reinforced concrete slabs, post-tensioned together and connected to the strong laboratory floor. The slip table is driven by a hydraulic actuator governed by a 407 MTS controller which employs a proportional-integral-derivative-feedforward-differential pressure algorithm to control the actuator displacement. Feedback signals are provided by two LVDT's (monitoring the slip table relative displacement and the servovalve main stage spool position) and by one differential pressure transducer (monitoring the actuator force). The dynamic actuator-foundation-specimen system is modeled and analyzed by combining linear control theory and linear structural dynamics. The analytical model developed accounts for the effects of actuator oil compressibility, oil leakage in the actuator, time delay in the response of the servovalve spool to a given electrical signal, foundation flexibility, and dynamic characteristics of multi-degree-of-freedom specimens. In order to study the actual dynamic behavior of the shaking table, the transfer function between target and actual table accelerations were identified using experimental results and spectral estimation techniques. The power spectral density of the system input and the cross power spectral density of the table input and output were estimated using the Bartlett's spectral estimation method. The experimentally-estimated table acceleration transfer functions obtained for different working conditions are correlated with their analytical counterparts. As a result of this comprehensive correlation study, a thorough understanding of the shaking table dynamics and its sensitivities to control and payload parameters is obtained. Moreover, the correlation study leads to a calibrated analytical model of the shaking table of high predictive ability. It is concluded that, in its present conditions, the Rice shaking table is able to reproduce, with a high degree of accuracy, model earthquake accelerations time histories in the frequency bandwidth from 0 to 75 Hz. Furthermore, the exhaustive analysis performed indicates that the table transfer function is not significantly affected by the presence of a large (in terms of weight) payload with a fundamental frequency up to 20 Hz. Payloads having a higher fundamental frequency do affect significantly the shaking table performance and require a modification of the table control gain setting that can be easily obtained using the predictive analytical model of the shaking table. The complete description of a structural dynamic experiment performed using the Rice shaking table facility is also reported herein. The object of this experimentation was twofold: (1) to verify the testing capability of the shaking table and, (2) to experimentally validate a simplified theory developed by the author, which predicts the maximum rotational response developed by seismic isolated building structures characterized by non-coincident centers of mass and rigidity, when subjected to strong earthquake ground motions.

System technology analysis of aeroassisted orbital transfer vehicles: Moderate lift/drag (0.75-1.5). Volume 3: Cost estimates and work breakdown structure/dictionary, phase 1 and 2

NASA Technical Reports Server (NTRS)

1985-01-01

Technology payoffs of representative ground based (Phase 1) and space based (Phase 2) mid lift/drag ratio aeroassisted orbit transfer vehicles (AOTV) were assessed and prioritized. A narrative summary of the cost estimates and work breakdown structure/dictionary for both study phases is presented. Costs were estimated using the Grumman Space Programs Algorithm for Cost Estimating (SPACE) computer program and results are given for four AOTV configurations. The work breakdown structure follows the standard of the joint government/industry Space Systems Cost Analysis Group (SSCAG). A table is provided which shows cost estimates for each work breakdown structure element.

Ceramic inspection system

DOEpatents

Werve, Michael E [Modesto, CA

2006-05-16

A system for inspecting a ceramic component. The ceramic component is positioned on a first rotary table. The first rotary table rotates the ceramic component. Light is directed toward the first rotary table and the rotating ceramic component. A detector is located on a second rotary table. The second rotary table is operably connected to the first rotary table and the rotating ceramic component. The second rotary table is used to move the detector at an angle to the first rotary table and the rotating ceramic component.

New Tables For IABG's 320kN Shaker System: Design And Procurement Process

NASA Astrophysics Data System (ADS)

Baumgartl, Ralf

2012-07-01

For more than 25 years IABG is operating its 320kN vibration system in testing of space and non-space applications. The vibration system is a multi shaker system, using four electrodynamic shakers, driving a 3x3m2 head expander and a 3x3m2 slip table. During the recent years a modernisation program of the shaker system has been implemented. The purpose of this program was to exchange system components, which have reached their expected duration of life, as well as to exchange components which did no longer fulfil the state-of-the-art requirements in testing and thus to adapt the vibration system to future challenges. Two major components of the shaker system, which have been covered during the modernisation program, are the shaker tables (the head expander and the slip table). Being the direct interface of a vibration test facility to a specimen, the shaker tables are crucial regarding the shaker system overall performance. And this fact applies even more for shaker systems with large tables, because there are no off-the-shelf solutions in this area. During the recent 5 years IABG specified, designed and procured a new head expander and a new slip table for the 320kN shaker system. This paper describes the overall process investigating on the following listed aspects: - general requirements for the tables - definition of boundary conditions and guidance principles - specific areas of interest - definition of the table material and the manufacturing method - design solutions - challenges during manufacturing - results - table properties

Cardiopulmonary performance testing using a robotics-assisted tilt table: feasibility assessment in able-bodied subjects.

PubMed

Saengsuwan, J; Laubacher, M; Nef, T; Hunt, K J

2014-01-01

Robotics-assisted tilt table technology was introduced for early rehabilitation of neurological patients. It provides cyclical stepping movement and physiological loading of the legs. The aim of the present study was to assess the feasibility of this type of device for peak cardiopulmonary performance testing using able-bodied subjects. A robotics-assisted tilt table was augmented with force sensors in the thigh cuffs and a work rate estimation algorithm. A custom visual feedback system was employed to guide the subjects' work rate and to provide real time feedback of actual work rate. Feasibility assessment focused on: (i) implementation (technical feasibility), and (ii) responsiveness (was there a measurable, high-level cardiopulmonary reaction?). For responsiveness testing, each subject carried out an incremental exercise test to the limit of functional capacity with a work rate increment of 5 W/min in female subjects and 8 W/min in males. 11 able-bodied subjects were included (9 male, 2 female; age 29.6 ± 7.1 years: mean ± SD). Resting oxygen uptake (O_{2}) was 4.6 ± 0.7 mL/min/kg and O_{2}peak was 32.4 ± 5.1 mL/min/kg; this mean O_{2}peak was 81.1% of the predicted peak value for cycle ergometry. Peak heart rate (HRpeak) was 177.5 ± 9.7 beats/min; all subjects reached at least 85% of their predicted HRpeak value. Respiratory exchange ratio (RER) at O_{2}peak was 1.02 ± 0.07. Peak work rate) was 61.3 ± 15.1 W. All subjects reported a Borg CR10 value for exertion and leg fatigue of 7 or more. The robotics-assisted tilt table is deemed feasible for peak cardiopulmonary performance testing: the approach was found to be technically implementable and substantial cardiopulmonary responses were observed. Further testing in neurologically-impaired subjects is warranted.

Tables for pressure of air on coming to rest from various speeds

NASA Technical Reports Server (NTRS)

Zahm, A F; Louden, F A

1930-01-01

In Technical Report no. 247 of the National Advisory Committee for Aeronautics theoretical formulas are given from which was computed a table for the pressure of air on coming to rest from various speeds, such as those of aircraft and propeller blades. In that report, the table gave incompressible and adiabatic stop pressures of air for even-speed intervals in miles per hour and for some even-speed intervals in knots per hour. Table II of the present report extends the above-mentioned table by including the stop pressures of air for even-speed intervals in miles per hour, feet per-second, knots per hour, kilometers per hour, and meters per second. The pressure values in table II are also more exact than values given in the previous table. To furnish the aeronautical engineer with ready numerical formulas for finding the pressure of air on coming to rest, table I has been derived for the standard values specified below it. This table first presents the theoretical pressure-speed formulas and their working forms in C. G. S. Units as given in NACA Technical Report No. 247, then furnishes additional working formulas for several special units of speed. (author)

Ablation, Thermal Response, and Chemistry Program for Analysis of Thermal Protection Systems

NASA Technical Reports Server (NTRS)

Milos, Frank S.; Chen, Yih-Kanq

2010-01-01

In previous work, the authors documented the Multicomponent Ablation Thermochemistry (MAT) and Fully Implicit Ablation and Thermal response (FIAT) programs. In this work, key features from MAT and FIAT were combined to create the new Fully Implicit Ablation, Thermal response, and Chemistry (FIATC) program. FIATC is fully compatible with FIAT (version 2.5) but has expanded capabilities to compute the multispecies surface chemistry and ablation rate as part of the surface energy balance. This new methodology eliminates B' tables, provides blown species fractions as a function of time, and enables calculations that would otherwise be impractical (e.g. 4+ dimensional tables) such as pyrolysis and ablation with kinetic rates or unequal diffusion coefficients. Equations and solution procedures are presented, then representative calculations of equilibrium and finite-rate ablation in flight and ground-test environments are discussed.

"Hyperstat": an educational and working tool in epidemiology.

PubMed

Nicolosi, A

1995-01-01

The work of a researcher in epidemiology is based on studying literature, planning studies, gathering data, analyzing data and writing results. Therefore he has need for performing, more or less, simple calculations, the need for consulting or quoting literature, the need for consulting textbooks about certain issues or procedures, and the need for looking at a specific formula. There are no programs conceived as a workstation to assist the different aspects of researcher work in an integrated fashion. A hypertextual system was developed which supports different stages of the epidemiologist's work. It combines database management, statistical analysis or planning, and literature searches. The software was developed on Apple Macintosh by using Hypercard 2.1 as a database and HyperTalk as a programming language. The program is structured in 7 "stacks" or files: Procedures; Statistical Tables; Graphs; References; Text; Formulas; Help. Each stack has its own management system with an automated Table of Contents. Stacks contain "cards" which make up the databases and carry executable programs. The programs are of four kinds: association; statistical procedure; formatting (input/output); database management. The system performs general statistical procedures, procedures applicable to epidemiological studies only (follow-up and case-control), and procedures for clinical trials. All commands are given by clicking the mouse on self-explanatory "buttons". In order to perform calculations, the user only needs to enter the data into the appropriate cells and then click on the selected procedure's button. The system has a hypertextual structure. The user can go from a procedure to other cards following the preferred order of succession and according to built-in associations. The user can access different levels of knowledge or information from any stack he is consulting or operating. From every card, the user can go to a selected procedure to perform statistical calculations, to the reference database management system, to the textbook in which all procedures and issues are discussed in detail, to the database of statistical formulas with automated table of contents, to statistical tables with automated table of contents, or to the help module. he program has a very user-friendly interface and leaves the user free to use the same format he would use on paper. The interface does not require special skills. It reflects the Macintosh philosophy of using windows, buttons and mouse. This allows the user to perform complicated calculations without losing the "feel" of data, weight alternatives, and simulations. This program shares many features in common with hypertexts. It has an underlying network database where the nodes consist of text, graphics, executable procedures, and combinations of these; the nodes in the database correspond to windows on the screen; the links between the nodes in the database are visible as "active" text or icons in the windows; the text is read by following links and opening new windows. The program is especially useful as an educational tool, directed to medical and epidemiology students. The combination of computing capabilities with a textbook and databases of formulas and literature references, makes the program versatile and attractive as a learning tool. The program is also helpful in the work done at the desk, where the researcher examines results, consults literature, explores different analytic approaches, plans new studies, or writes grant proposals or scientific articles.

Free-floating dual-arm robots for space assembly

NASA Technical Reports Server (NTRS)

Agrawal, Sunil Kumar; Chen, M. Y.

1994-01-01

Freely moving systems in space conserve linear and angular momentum. As moving systems collide, the velocities get altered due to transfer of momentum. The development of strategies for assembly in a free-floating work environment requires a good understanding of primitives such as self motion of the robot, propulsion of the robot due to onboard thrusters, docking of the robot, retrieval of an object from a collection of objects, and release of an object in an object pool. The analytics of such assemblies involve not only kinematics and rigid body dynamics but also collision and impact dynamics of multibody systems. In an effort to understand such assemblies in zero gravity space environment, we are currently developing at Ohio University a free-floating assembly facility with a dual-arm planar robot equipped with thrusters, a free-floating material table, and a free-floating assembly table. The objective is to pick up workpieces from the material table and combine them into prespecified assemblies. This paper presents analytical models of assembly primitives and strategies for overall assembly. A computer simulation of an assembly is developed using the analytical models. The experiment facility will be used to verify the theoretical predictions.

Design of a workstation table with improved crashworthiness performance

DOT National Transportation Integrated Search

2005-11-05

Work is currently underway to develop strategies to protect rail passengers seated at workstation tables during a collision or derailment. Investigations have shown that during a collision, these tables can present a hostile secondary impact environm...

Periodic Table of Elements: Los Alamos National Laboratory

Science.gov Websites

, Communication Specialist talks about the Periodic Table of Elements 7/17/17 Back to Elements List Seaborgium is Phone Periodic Table of Elements: LANL Chemistry Division » Periodic Table of Elements Chemistry the Elements Chemical Properties Elements List Periodic Table Download News LANL Biofuels Work

18. NBS SUIT LAB. OVERALL VIEW. ALL WORK TABLES WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. NBS SUIT LAB. OVERALL VIEW. ALL WORK TABLES WITH MISCELLANEOUS SUIT COMPONENTS AND SUPPLIES. TERRY WEST TO LEFT, AND PAUL DUMBACHER TO RIGHT. - Marshall Space Flight Center, Neutral Buoyancy Simulator Facility, Rideout Road, Huntsville, Madison County, AL

Design and dosimetry of small animal radiation facilities

NASA Astrophysics Data System (ADS)

Rodriguez, Manuel R.

The aim of this work was to develop an irradiation system for radiobiology studies. We designed a novel image-guided micro-irradiator capable of partial-body zebrafish embryo irradiation. The radiation source is a 50 kV photon beam from a miniature x-ray source (Xoft Inc., CA). The source is inserted in a cylindrical brass collimator, 3 cm in diameter and 3 cm in length. The collimator has a 1 mm-diameter pinhole along the longitudinal axis, which provides a well-focused beam with a sharp penumbra. A photodiode is installed at one exit of the pinhole collimator to monitor the photon dose rate. The source with the collimator is attached under a movable table. A video camera, connected to the computer, is placed above the movable table to record position of the specimens in relation to the pinhole collimator. The captured images are analyzed, and the relative distances between the specimens and the pinhole are calculated. The coordinates are sent to the computer-controlled movable table to accurately position the specimens in the beam. Monte Carlo simulations were performed to characterize dosimetric properties of the system, to determine dosimetric sensitivity, and to help in the design. The image-guidance and high precision of the movable table enable very accurate specimen position. The beam monitoring system provides accurate, fast and easy dose determination. Portability and self-shielding make this system suitable for any radiobiology laboratory. This novel micro-irradiator is appropriate for partial irradiation of zebrafish embryos; however its potential use is much wider like irradiation of cell cultures or other small specimens.

40 CFR Table 3 to Subpart Eeee of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... Monitoring Systems (CEMS) 3 Table 3 to Subpart EEEE of Part 60 Protection of Environment ENVIRONMENTAL..., Subpt. EEEE, Table 3 Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.2940, you must comply with the following: For the followingpollutants Use...

40 CFR Table 3 to Subpart Eeee of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2011 CFR

2011-07-01

... Monitoring Systems (CEMS) 3 Table 3 to Subpart EEEE of Part 60 Protection of Environment ENVIRONMENTAL..., Subpt. EEEE, Table 3 Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.2940, you must comply with the following: For the followingpollutants Use...

76 FR 8990 - Hours of Service of Drivers; Availability of Supplemental Documents and Corrections to Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-16

.... FMCSA used a look-up table for scaling the individual hours of work in the previous week. Look-up tables...). Column C (cells C93-137) presents the values scaled to our average work (52 hours per week of work) and... Evaluation to link the hours worked in the previous week to fatigue the following week. On January 28, 2011...

NASA MSFC hardware in the loop simulations of automatic rendezvous and capture systems

NASA Technical Reports Server (NTRS)

Tobbe, Patrick A.; Naumann, Charles B.; Sutton, William; Bryan, Thomas C.

1991-01-01

Two complementary hardware-in-the-loop simulation facilities for automatic rendezvous and capture systems at MSFC are described. One, the Flight Robotics Laboratory, uses an 8 DOF overhead manipulator with a work volume of 160 by 40 by 23 feet to evaluate automatic rendezvous algorithms and range/rate sensing systems. The other, the Space Station/Station Operations Mechanism Test Bed, uses a 6 DOF hydraulic table to perform docking and berthing dynamics simulations.

40 CFR Table 9 to Subpart IIIii of... - Required Records for Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 9 Table 9 to Subpart IIIII of Part 63... other deficiency in a cell room floor, pillar, or beam that could cause liquid mercury to become trapped... hydrogen leak identified during an inspection required by Table 2 to this subpart or at any other time a...

40 CFR Table 9 to Subpart IIIii of... - Required Records for Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 9 Table 9 to Subpart IIIII of Part 63... other deficiency in a cell room floor, pillar, or beam that could cause liquid mercury to become trapped... hydrogen leak identified during an inspection required by Table 2 to this subpart or at any other time a...

40 CFR Table 7 to Subpart Eeee of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... equivalent control that meets the requirements in Table 4 to this subpart, item 1.a i. After emptying and... out a leak detection and repair program or equivalent control according to one of the subparts listed... (Non-Gasoline) Pt. 63, Subpt. EEEE, Table 7 Table 7 to Subpart EEEE of Part 63—Initial Compliance With...

40 CFR Table 7 to Subpart Eeee of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... equivalent control that meets the requirements in Table 4 to this subpart, item 1.a i. After emptying and... out a leak detection and repair program or equivalent control according to one of the subparts listed... (Non-Gasoline) Pt. 63, Subpt. EEEE, Table 7 Table 7 to Subpart EEEE of Part 63—Initial Compliance With...

40 CFR Table 7 to Subpart Eeee of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... equivalent control that meets the requirements in Table 4 to this subpart, item 1.a i. After emptying and... out a leak detection and repair program or equivalent control according to one of the subparts listed... (Non-Gasoline) Pt. 63, Subpt. EEEE, Table 7 Table 7 to Subpart EEEE of Part 63—Initial Compliance With...

PISA, Policy and Persuasion: Translating Complex Conditions into Education "Best Practice"

ERIC Educational Resources Information Center

Auld, Euan; Morris, Paul

2016-01-01

Education reform is increasingly portrayed as a means to improve a nation's global competitiveness as measured by its performance in international league tables of pupil achievement. This has created a demand for comparative research which identifies "what works" in high-performing school systems. A diverse array of consultancies, thinks…

40 CFR Table 5 to Subpart Uuuu of... - Continuous Compliance With Emission Limits and Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... material balance that includes the pertinent data used to determine the percent reduction of total sulfide... material balance; and (3) complying with the continuous compliance requirements for closed-vent systems. 2... material balance that includes the pertinent data used to determine the percent reduction of toluene...

40 CFR Table 5 to Subpart Uuuu of... - Continuous Compliance With Emission Limits and Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... material balance that includes the pertinent data used to determine the percent reduction of total sulfide... material balance; and (3) complying with the continuous compliance requirements for closed-vent systems. 2... material balance that includes the pertinent data used to determine the percent reduction of toluene...

Yours, Mine, Theirs: Multiple Generations in Today's Workplace

ERIC Educational Resources Information Center

Grotophorst, Julie

2011-01-01

For the first time in history, four distinct generations are sharing the same workspace. Veterans, Baby Boomers, Gen-Xers, and Generation Y (the Millennials) are all bringing very different life experiences, expectations, and value systems to the work table. How do leaders bridge the gap among these generations and provide common ground on which…

Secure and Resilient Cloud Computing for the Department of Defense

DTIC Science & Technology

2015-11-16

platform as a service (PaaS), and software as a service ( SaaS )—that target system administrators, developers, and end-users respectively (see Table 2...interfaces (API) and services Medium Amazon Elastic MapReduce, MathWorks Cloud, Red Hat OpenShift SaaS Full-fledged applications Low Google gMail

37. July 1974. WOOD SHOP, VIEW LOOKING NORTHWEST, SHOWING THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. July 1974. WOOD SHOP, VIEW LOOKING NORTHWEST, SHOWING THE PLANER WITH ITS BELT CHASE FROM THE BASEMENT LINESHAFT AND THE BELTING SYSTEM FOR THE TABLE-SHAPER. BEYOND THE PLANER IS THE BAND SAW. - Gruber Wagon Works, Pennsylvania Route 183 & State Hill Road at Red Bridge Park, Bernville, Berks County, PA

The US Nuclear Data Network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-10-19

This report discusses the following topics: US Nuclear Data Network Meeting; TUNL A=3--20 Data Project Activity Report 1993; INEL Mass-chain Evaluation Project Activity Report for 1993; 1993 Isotopes; Nuclear Data Project Activity Report; The NNDC Activity Report Parts A and B; Minutes of the Formats and Procedures Subcommittee; Evaluation of High-spin Nuclear Data for ENSDF and Table of Superdeformed Nuclear Bands; Proposal for Support of a Experimental High-spin; Data File/Data-Network Coordinator; Radioactive Decay and Applications; A Plan for a Horizontal Evaluation of Decay Data; ENSDF On-line System; The MacNuclide Project Expanding the Scope of the Nuclear Structure Reference File; ENSDAT:more » Evaluated Nuclear Structure Drawings and Tables; Cross Section Evaluation Working Group (CSEWG) and CSEWG Strategy Session; A Draft Proposal for a USNDN Program Advisory Council; Recommendations of Focus Group 1; Recommendations of Focus Group 2; Recommendations of Focus Group 3; Recommendations of Focus Group 4; The Table of Isotopes; The Isotopes CD-ROM; Electronic Table of Isotopes (ETOI); and Electronic Access to Nuclear Data.« less

40 CFR Table 4 to Subpart Ffff of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Monitoring Systems (CEMS) 4 Table 4 to Subpart FFFF of Part 60 Protection of Environment... Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 4 Table 4 to Subpart FFFF of Part 60—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.3039, you...

40 CFR Table 4 to Subpart Ffff of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Monitoring Systems (CEMS) 4 Table 4 to Subpart FFFF of Part 60 Protection of Environment... Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 4 Table 4 to Subpart FFFF of Part 60—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.3039, you...

40 CFR Table 4 to Subpart Ffff of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Monitoring Systems (CEMS) 4 Table 4 to Subpart FFFF of Part 60 Protection of Environment... Construction On or Before December 9, 2004 Pt. 60, Subpt. FFFF, Table 4 Table 4 to Subpart FFFF of Part 60—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.3039, you...

40 CFR Table 31 to Subpart Uuu of... - Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for HAP Emissions...

40 CFR Table 31 to Subpart Uuu of... - Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment..., Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for HAP Emissions...

Using neural networks and Dyna algorithm for integrated planning, reacting and learning in systems

NASA Technical Reports Server (NTRS)

Lima, Pedro; Beard, Randal

1992-01-01

The traditional AI answer to the decision making problem for a robot is planning. However, planning is usually CPU-time consuming, depending on the availability and accuracy of a world model. The Dyna system generally described in earlier work, uses trial and error to learn a world model which is simultaneously used to plan reactions resulting in optimal action sequences. It is an attempt to integrate planning, reactive, and learning systems. The architecture of Dyna is presented. The different blocks are described. There are three main components of the system. The first is the world model used by the robot for internal world representation. The input of the world model is the current state and the action taken in the current state. The output is the corresponding reward and resulting state. The second module in the system is the policy. The policy observes the current state and outputs the action to be executed by the robot. At the beginning of program execution, the policy is stochastic and through learning progressively becomes deterministic. The policy decides upon an action according to the output of an evaluation function, which is the third module of the system. The evaluation function takes the following as input: the current state of the system, the action taken in that state, the resulting state, and a reward generated by the world which is proportional to the current distance from the goal state. Originally, the work proposed was as follows: (1) to implement a simple 2-D world where a 'robot' is navigating around obstacles, to learn the path to a goal, by using lookup tables; (2) to substitute the world model and Q estimate function Q by neural networks; and (3) to apply the algorithm to a more complex world where the use of a neural network would be fully justified. In this paper, the system design and achieved results will be described. First we implement the world model with a neural network and leave Q implemented as a look up table. Next, we use a lookup table for the world model and implement the Q function with a neural net. Time limitations prevented the combination of these two approaches. The final section discusses the results and gives clues for future work.

Tuple spaces in hardware for accelerated implicit routing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Zachary Kent; Tripp, Justin

2010-12-01

Organizing and optimizing data objects on networks with support for data migration and failing nodes is a complicated problem to handle as systems grow. The goal of this work is to demonstrate that high levels of speedup can be achieved by moving responsibility for finding, fetching, and staging data into an FPGA-based network card. We present a system for implicit routing of data via FPGA-based network cards. In this system, data structures are requested by name, and the network of FPGAs finds the data within the network and relays the structure to the requester. This is acheived through successive examinationmore » of hardware hash tables implemented in the FPGA. By avoiding software stacks between nodes, the data is quickly fetched entirely through FPGA-FPGA interaction. The performance of this system is orders of magnitude faster than software implementations due to the improved speed of the hash tables and lowered latency between the network nodes.« less

Apollo by the Numbers: A Statistical Reference

NASA Technical Reports Server (NTRS)

Orloff, Richard; Garber, Stephen (Technical Monitor)

2000-01-01

The purpose of this work is to provide researchers, students, and space enthusiasts with a comprehensive reference for facts about Project Apollo, America's effort to put humans in the Moon. Research for this work started in 1988, when the author discovered that, despite the number of excellent books that focused on the drama of events that highlighted Apollo, there were none that focused on the drama of the numbers. This book is separated into two parts. The first part contains narratives for the Apollo 1 fire and the 11 flown Apollo missions. Included after each narrative is a series of data tables, followed by a comprehensive timeline of events from just before liftoff to just after crew and spacecraft recovery. The second part contains more than 50 tables. These tables organize much of the data from the narratives in one place so they can be compared among all missions. The tables offer additional data as well. The reader can select a specific mission narrative or specific data table by consulting the Table of Contents.

Mathematical model for the simulation of Dynamic Docking Test System (DDST) active table motion

NASA Technical Reports Server (NTRS)

Gates, R. M.; Graves, D. L.

1974-01-01

The mathematical model developed to describe the three-dimensional motion of the dynamic docking test system active table is described. The active table is modeled as a rigid body supported by six flexible hydraulic actuators which produce the commanded table motions.

An Investigation of Applications for Thermodynamic Work Potential Methods: Working Tables and Charts for Estimation of Thermodynamic Work Potential in Equilibrium Mixtures of Jet-A and Air

NASA Technical Reports Server (NTRS)

Mavris, Dimitri; Roth, Bryce; McDonald, Rob

2002-01-01

The objective of this report is to provide a tool to facilitate the application of thermodynamic work potential methods to aircraft and engine analysis. This starts with a discussion of the theoretical background underlying these methods, which is then used to derive various equations useful for thermodynamic analysis of aircraft engines. The work potential analysis method is implemented in the form of a set of working charts and tables that can be used to graphically evaluate work potential stored in high-enthalpy gas. The range of validity for these tables is 300 to 36,000 R, pressures between between 0.01 atm and 100 atm, and fuel-air ratios from zero to stoichiometric. The derivations and charts assume mixtures of Jet-A and air as the working fluid. The thermodynamic properties presented in these charts were calculated based upon standard thermodynamic curve fits.

The next step in biology: a periodic table?

PubMed

Dhar, Pawan K

2007-08-01

Systems biology is an approach to explain the behaviour of a system in relation to its individual components. Synthetic biology uses key hierarchical and modular concepts of systems biology to engineer novel biological systems. In my opinion the next step in biology is to use molecule-to-phenotype data using these approaches and integrate them in the form a periodic table. A periodic table in biology would provide chassis to classify, systematize and compare diversity of component properties vis-a-vis system behaviour. Using periodic table it could be possible to compute higher- level interactions from component properties. This paper examines the concept of building a bio-periodic table using protein fold as the fundamental unit.

Conversion tables for use with the National Fire-Danger Rating System in the Intermountain area

Treesearch

Dwight S. Stockstad; Richard J. Barney

1964-01-01

Two tables prepared for use with the National Fire-Danger Rating System replace 10 tables previously used with the Model-8 Fire-Danger Rating System. They provide for the conversion of Spread Index values at various altitudes, aspects, and times of day. A rate of spread table facilitates converting Spread Index values to chains per hour of perimeter increase for...

40 CFR Table 31 to Subpart Uuu of... - Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment... Units Pt. 63, Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for...

40 CFR Table 31 to Subpart Uuu of... - Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment... Units Pt. 63, Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for...

40 CFR Table 31 to Subpart Uuu of... - Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Continuous Monitoring Systems for HAP Emissions From Sulfur Recovery Units 31 Table 31 to Subpart UUU of Part 63 Protection of Environment... Units Pt. 63, Subpt. UUU, Table 31 Table 31 to Subpart UUU of Part 63—Continuous Monitoring Systems for...

Dynamic Docking Test System (DDTS) active table frequency response test results. [Apollo Soyuz Test Project

NASA Technical Reports Server (NTRS)

Gates, R. M.

1974-01-01

Results are presented of the frequency response test performed on the dynamic docking test system (DDTS) active table. Sinusoidal displacement commands were applied to the table and the dynamic response determined from measured actuator responses and accelerometers mounted to the table and one actuator.

Improving Drive Files for Vehicle Road Simulations

NASA Astrophysics Data System (ADS)

Cherng, John G.; Goktan, Ali; French, Mark; Gu, Yi; Jacob, Anil

2001-09-01

Shaker tables are commonly used in laboratories for automotive vehicle component testing to study durability and acoustics performance. An example is development testing of car seats. However, it is difficult to repeat the measured road data perfectly with the response of a shaker table as there are basic differences in dynamic characteristics between a flexible vehicle and substantially rigid shaker table. In addition, there are performance limits in the shaker table drive systems that can limit correlation. In practice, an optimal drive signal for the actuators is created iteratively. During each iteration, the error between the road data and the response data is minimised by an optimising algorithm which is generally a part of the feed back loop of the shake table controller. This study presents a systematic investigation to the errors in time and frequency domains as well as joint time-frequency domain and an evaluation of different digital signal processing techniques that have been used in previous work. In addition, we present an innovative approach that integrates the dynamic characteristics of car seats and the human body into the error-minimising iteration process. We found that the iteration process can be shortened and the error reduced by using a weighting function created by normalising the frequency response function of the car seat. Two road data test sets were used in the study.

A Critical Analysis of U.S. Army Accessions through Socioeconomic Consideration between 1970 and 1984.

DTIC Science & Technology

1985-06-01

ADDRESS 10. PROGRAM ELEMENT, PROJECT. TASK AREA & WORK UNIT NUMBERS Naval Postgraduate School Monterey, California 93943 11. CONTROLLING OFFICE NAME AND...determine the sccioeccnomic representativeness of the Army’s enlistees in that iarticular year. In addition, the socioeconomic overviev of Republic cf...accomplished with the use of the Statistical Analysis System (SAS), an integrated computer system for data analysis. 32 TABLE 2 The States in Each District

Corps of Engineers Operations and Maintenance Budget Decision Support System (COMB-DSS): System Concept, Design and Prototype Evaluation. Volume 2. Appendixes B Through G.

DTIC Science & Technology

1994-04-01

Rather, it should provide, whenever possible, information on the location and/or quantity of work. Examples of good descriptions are as follows: Major...03100 D1UMNG IrMMlC CHAJE DOI TABI3s IMASON 1 -eascode 1323035 2 reason T231 64 code lookup table giving text for each integer reascode re*acode reaon 0

Design And Implementation Of Integrated Vision-Based Robotic Workcells

NASA Astrophysics Data System (ADS)

Chen, Michael J.

1985-01-01

Reports have been sparse on large-scale, intelligent integration of complete robotic systems for automating the microelectronics industry. This paper describes the application of state-of-the-art computer-vision technology for manufacturing of miniaturized electronic components. The concepts of FMS - Flexible Manufacturing Systems, work cells, and work stations and their control hierarchy are illustrated in this paper. Several computer-controlled work cells used in the production of thin-film magnetic heads are described. These cells use vision for in-process control of head-fixture alignment and real-time inspection of production parameters. The vision sensor and other optoelectronic sensors, coupled with transport mechanisms such as steppers, x-y-z tables, and robots, have created complete sensorimotor systems. These systems greatly increase the manufacturing throughput as well as the quality of the final product. This paper uses these automated work cells as examples to exemplify the underlying design philosophy and principles in the fabrication of vision-based robotic systems.

VizieR Online Data Catalog: STAGGER-grid of 3D stellar models. V. (Chiavassa+, 2018)

NASA Astrophysics Data System (ADS)

Chiavassa, A.; Casagrande, L.; Collet, R.; Magic, Z.; Bigot, L.; Thevenin, F.; Asplund, M.

2018-01-01

Table B0: RHD simulations' stellar parameters, bolometric magnitude, and bolometric correction for Johnson-Cousins, 2MASS, SDSS (columns 13 to 17), and Gaia systems Table 4: RHD simulations' stellar parameters, bolometric magnitude, and bolometric correction for SkyMapper photometric system, and Stroemgren index b-y, m1=(v-b)-(b-y), and c1=(u-v)-(v-b) Table 5: RHD simulations' stellar parameters, bolometric magnitude, and bolometric correction for the HST-WFC3 in VEGA system Table 6: RHD simulations' stellar parameters, bolometric magnitude, and bolometric correction for the HST-WFC3 in ST system Table 7: RHD simulations' stellar parameters, bolometric magnitude, and bolometric correction for the HST-WFC3 in AB system (5 data files).

The Medical Gopher — A Microcomputer Based Physician Work Station

PubMed Central

McDonald, Clement J.

1984-01-01

We've developed a microcomputer medical work station intended to reduce the physician's “gopher” work of fetching, reviewing, organizing and writing that consumes his day. The system requires extensive physician interaction; so we have developed a fast and consistent menu-oriented user interface. It provides facilities for entering prescriptions, orders, problems and other medical record information and for generating flowsheets, executing reminder rules, providing ad hoc retrievals and reporting facts about drugs, tests and differential diagnoses. Each work station is connected to a central server (currently a VAX 117/80) in a network configuration, but carries all of its own programs, tables and medical records for a few hundred patients, locally. This system is tested but not yet tried. Questions remain about physician's acceptance and the true usefullness of such a work station.

40 CFR Table 5 to Subpart Uuuu of... - Continuous Compliance With Emission Limits and Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

...) maintaining a material balance that includes the pertinent data used to determine the percent reduction of... pertinent data from the material balance; and (3) complying with the continuous compliance requirements for... systems (1) maintaining a material balance that includes the pertinent data used to determine the percent...

40 CFR Table 5 to Subpart Uuuu of... - Continuous Compliance With Emission Limits and Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

...) maintaining a material balance that includes the pertinent data used to determine the percent reduction of... pertinent data from the material balance; and (3) complying with the continuous compliance requirements for... systems (1) maintaining a material balance that includes the pertinent data used to determine the percent...

40 CFR Table 5 to Subpart Uuuu of... - Continuous Compliance With Emission Limits and Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

...) maintaining a material balance that includes the pertinent data used to determine the percent reduction of... pertinent data from the material balance; and (3) complying with the continuous compliance requirements for... systems (1) maintaining a material balance that includes the pertinent data used to determine the percent...

40 CFR Table 4 to Subpart Wwww of... - Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

..., or sumps via covered troughs, pipes, or other covered conveyance that shields the resin from the... when they are being charged or filled, and vii. cover or shield from ambient air resin delivery systems... less may be open when active mixing is taking place, or during periods when they are in process (i.e...

40 CFR Table 4 to Subpart Wwww of... - Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

..., or sumps via covered troughs, pipes, or other covered conveyance that shields the resin from the... when they are being charged or filled, and vii. cover or shield from ambient air resin delivery systems... less may be open when active mixing is taking place, or during periods when they are in process (i.e...

40 CFR Table 4 to Subpart Wwww of... - Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

..., or sumps via covered troughs, pipes, or other covered conveyance that shields the resin from the... when they are being charged or filled, and vii. cover or shield from ambient air resin delivery systems... less may be open when active mixing is taking place, or during periods when they are in process (i.e...

40 CFR Table 4 to Subpart Wwww of... - Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

..., or sumps via covered troughs, pipes, or other covered conveyance that shields the resin from the... when they are being charged or filled, and vii. cover or shield from ambient air resin delivery systems... less may be open when active mixing is taking place, or during periods when they are in process (i.e...

40 CFR 63.1567 - What are my requirements for inorganic HAP emissions from catalytic reforming units?

Code of Federal Regulations, 2010 CFR

2010-07-01

... ppmv. (iv) If you are required to use a colormetric tube sampling system to demonstrate continuous... limitations and work practice standards must I meet? You must: (1) Meet each emission limitation in Table 22 to this subpart that applies to you. If you operate a catalytic reforming unit in which different...

40 CFR Table 5 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Transfer Operations

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Halogenated Group 1 transfer operation vent stream for which you use a combustion device to control organic... your transfer operations. For each . . . You must. . . . 1. Group 1 transfer operation vent stream a... system to any combination of control devices (except a flare); or b. Reduce emissions of total organic...

40 CFR Table 5 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Transfer Operations

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Halogenated Group 1 transfer operation vent stream for which you use a combustion device to control organic... your transfer operations. For each . . . You must. . . . 1. Group 1 transfer operation vent stream a... system to any combination of control devices (except a flare); or b. Reduce emissions of total organic...

40 CFR Table 5 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Transfer Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Halogenated Group 1 transfer operation vent stream for which you use a combustion device to control organic... your transfer operations. For each . . . You must. . . . 1. Group 1 transfer operation vent stream a... system to any combination of control devices (except a flare); or b. Reduce emissions of total organic...

Macroscopic Neural Theories of Cognition

DTIC Science & Technology

2014-03-01

Autobiographical Memory -- 51% • Emotional Face Processing -- 14% • Single Word Reading -- 45% • N-Back Working Memory – 41% 22 A graphic comparison of...seven meta-analyses carried out for working memory is shown in Table 2. The results of this comparison were also clear—there was substantial...variation among the areas reported by the seven meta-analyses. Table 2. A Comparison of Seven Meta-analyses dealing with Working Memory . (Uttal, 2013

40 CFR Table 10 to Subpart Eeee of... - Continuous Compliance With Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Continuous Compliance With Work Practice Standards 10 Table 10 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National...

40 CFR Table 10 to Subpart Eeee of... - Continuous Compliance With Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Continuous Compliance With Work Practice Standards 10 Table 10 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National...

40 CFR Table 10 to Subpart Eeee of... - Continuous Compliance With Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Continuous Compliance With Work Practice Standards 10 Table 10 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National...

40 CFR Table 10 to Subpart Eeee of... - Continuous Compliance With Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Continuous Compliance With Work Practice Standards 10 Table 10 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission...

Eating at the table, on the couch and in bed: An exploration of different locus of commensality in the discourses of Brazilian working mothers.

PubMed

Scagliusi, Fernanda Baeza; da Rocha Pereira, Patrícia; Unsain, Ramiro Fernandez; de Morais Sato, Priscila

2016-08-01

Commensality is a remarkable human act, and tends to be more present among families. Nevertheless, it is possible that eating at the table is being taking for granted when one refers to family meals. Thus, this paper aims to analyze working mothers' discourses about family meals eaten at the table, on the couch and in the bed/bedroom. The participants were thirty mothers working in public universities of the Brazilian region called Baixada Santista. A qualitative study was conducted, using semi-structured interviews. In the transcripts the words "table", "couch", "bed", "bedroom" were located and the excerpts containing them were extracted and analyzed according to a classical and exploratory content analysis. The table is a significant component of meals that unite the family. While for some the meal at the table is an enjoyable moment, it is a stiff moment for others. Indeed, manners and the notion of hierarchy appeared only for the table. Regarding the couch, it seems that the family chose to eat there, because it is a more casual and relaxed setting. Eating in the bed was related to precarity, intimacy and casualness. In the three settings, watching television was a common practice, replacing or being added to talking. Commensality is such an important practice that appears in different settings and even in precarity contexts. The table emerged as the maximal cornerstone of commensality. However, when it was not present, new arrangements were made. Especially the couch seems to be a new commensal space, less formal and rigid, but able to allow some collective conviviality. Eating in the bed was a less common practice. Finally, the significant role that television assumed in meals is highlighted. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Physiological Demands of Table Tennis: A Review

PubMed Central

Kondrič, Miran; Zagatto, Alessandro Moura; Sekulić, Damir

2013-01-01

Although table tennis has a tradition lasting more than 100 years, relatively little is known about players’ physiological requirements – especially during competition. In this review we discuss research studies that have led to our current understanding of how the body functions during table tennis training and competition and how this is altered by training. Match and practice analysis of the table tennis game indicates that during intense practice and competition it is predominantly the anaerobic alactic system that is called into play, while the endurance system is relied on to recovery the anaerobic stores used during such effort. It is thus important for coaches to keep in mind that, while the anaerobic alactic system is the most energetic system used during periods of exertion in a table tennis game, a strong capacity for endurance is what helps a player recover quicker for the following match and the next day of competition. This paper provides a review of specific studies that relate to competitive table tennis, and highlights the need for training and research programs tailored to table tennis. Key Points Match and practice analysis of the table tennis game indicates that during intense practice and competition it is predominantly the anaerobic alactic system that is called into play. The endurance system is relied on to recovery the anaerobic stores used during hard practice and competition effort. It is important for coaches to keep in mind that, while the anaerobic alactic system is the most energetic system used during periods of exertion in a table tennis game, a strong capacity for endurance is what helps a player recover quicker for the following match and the next day of competition. PMID:24149139

Petroleum systems used to determine the assessment units in the San Joaquin Basin Province, California: Chapter 8 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

USGS Publications Warehouse

Magoon, Leslie B.; Lillis, Paul G.; Peters, Kenneth E.

2009-01-01

The figures and tables for each petroleum system and TPS are as follows: (1) the San Joaquin(?) petroleum system or the Neogene Nonassociated Gas TPS is a natural gas system in the southeast part of the province (figs. 8.3 through 8.8; table 8.5; this volume, chapter 22); (2) the Miocene TPS (this volume, chapters 13, 14, 15, 16, and 17) includes the McLure-Tulare(!) petroleum system north of the Bakersfield Arch (figs. 8.9 through 8.13; table 8.6), and the Antelope-Stevens(!) petroleum system south of the arch (figs. 8.14 through 8.18; table 8.7), and is summarized in figure 8.19; (3) the Eocene TPS (this volume, chapters 18 and 19) combines two petroleum systems, the Tumey-Temblor(.) covering much of the province (figs. 8.20 through 8.24; table 8.8) and the underlying Kreyenhagen-Temblor(!) (figs. 8.25 through 8.29: table 8.9), and is summarized in figure 8.30; (4) the Eocene-Miocene Composite TPS, formed by combining the Miocene and Eocene TPS (this volume, chapter 20); and (5) the Moreno-Nortonville(.) is both a petroleum system and a TPS consisting mainly of natural gas in the northern part of the province (figs. 8.31 through 8.36: table 8.10; this volume, chapter 21). Oil samples with geochemistry from surface seeps and wells used to map these petroleum systems are listed in table 8.11. Finally, the volume of oil and gas expelled by each pod of active source rock was calculated and compared with the discovered hydrocarbons in each petroleum system (figs. 8.37 through 8.39; tables 8.12 and 8.13).

40 CFR Table 6 to Subpart Hhhhh of... - Requirements for Heat Exchange Systems

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 13 2010-07-01 2010-07-01 false Requirements for Heat Exchange Systems... Manufacturing Pt. 63, Subpt. HHHHH, Table 6 Table 6 to Subpart HHHHH of Part 63—Requirements for Heat Exchange... your heat exchange systems. For each . . . You must . . . Heat exchange system, as defined in § 63.101...

40 CFR Table 6 to Subpart Hhhhh of... - Requirements for Heat Exchange Systems

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 14 2014-07-01 2014-07-01 false Requirements for Heat Exchange Systems... Manufacturing Pt. 63, Subpt. HHHHH, Table 6 Table 6 to Subpart HHHHH of Part 63—Requirements for Heat Exchange... your heat exchange systems. For each . . . You must . . . Heat exchange system, as defined in § 63.101...

40 CFR Table 6 to Subpart Hhhhh of... - Requirements for Heat Exchange Systems

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 14 2012-07-01 2011-07-01 true Requirements for Heat Exchange Systems... Manufacturing Pt. 63, Subpt. HHHHH, Table 6 Table 6 to Subpart HHHHH of Part 63—Requirements for Heat Exchange... your heat exchange systems. For each . . . You must . . . Heat exchange system, as defined in § 63.101...

40 CFR Table 6 to Subpart Hhhhh of... - Requirements for Heat Exchange Systems

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 14 2013-07-01 2013-07-01 false Requirements for Heat Exchange Systems... Manufacturing Pt. 63, Subpt. HHHHH, Table 6 Table 6 to Subpart HHHHH of Part 63—Requirements for Heat Exchange... your heat exchange systems. For each . . . You must . . . Heat exchange system, as defined in § 63.101...

40 CFR Table 6 to Subpart Hhhhh of... - Requirements for Heat Exchange Systems

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 13 2011-07-01 2011-07-01 false Requirements for Heat Exchange Systems... Manufacturing Pt. 63, Subpt. HHHHH, Table 6 Table 6 to Subpart HHHHH of Part 63—Requirements for Heat Exchange... your heat exchange systems. For each . . . You must . . . Heat exchange system, as defined in § 63.101...

40 CFR Table 6 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Wastewater Systems

Code of Federal Regulations, 2010 CFR

2010-07-01

... Requirements for Wastewater Systems 6 Table 6 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Wastewater Systems As required in § 63.11498, you must comply with the requirements for wastewater systems as shown in the following table. For...

40 CFR Table 6 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Wastewater Systems

Code of Federal Regulations, 2012 CFR

2012-07-01

... Requirements for Wastewater Systems 6 Table 6 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Wastewater Systems As required in § 63.11498, you must comply with the requirements for wastewater systems as shown in the following table. For...

40 CFR Table 6 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Wastewater Systems

Code of Federal Regulations, 2014 CFR

2014-07-01

... Requirements for Wastewater Systems 6 Table 6 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Wastewater Systems [As required in § 63.11498, you must comply with the requirements for wastewater systems as shown in the following table] For...

40 CFR Table 6 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Wastewater Systems

Code of Federal Regulations, 2013 CFR

2013-07-01

... Requirements for Wastewater Systems 6 Table 6 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Wastewater Systems [As required in § 63.11498, you must comply with the requirements for wastewater systems as shown in the following table] For...

Women in the Civil Engineer Corps.

DTIC Science & Technology

1986-01-01

order to "measure up"? __ often__ occasionally__ rarely_ never 18.Have you experienced sexual harrassment on the job? -__often ___occasionally __rarely...Assignments. . . . . . . 23 Sexual Harassment/Discrimination . . . 26 Relating Studies and Literature. . . . . . 28 IV. RESEARCH METHOLOGY...Table 13: Question 16. Work Harder . . . . . . . 56 Table 14: Question 17, Measure Up. . . . . . . . 57 Table 15: Question 18. Sexual Harassment

Modelling the effect of ascorbic acid, sodium metabisulphite and sodium chloride on the kinetic responses of lactic acid bacteria and yeasts in table olive storage using a specifically implemented Quasi-chemical primary model.

PubMed

Echevarria, R; Bautista-Gallego, J; Arroyo-López, F N; Garrido-Fernández, A

2010-04-15

The goal of this work was to apply the Quasi-chemical primary model (a system of four ordinary differential equations that derives from a hypothetical four-step chemical mechanism involving an antagonistic metabolite) in the study of the evolution of yeast and lactic acid bacteria populations during the storage of Manzanilla-Aloreña table olives subjected to different mixtures of ascorbic acid, sodium metabisulphite and NaCl. Firstly, the Quasi-chemical model was applied to microbial count data to estimate the growth-decay biological parameters. The model accurately described the evolution of both populations during storage, providing detailed information on the microbial behaviour. Secondly, these parameters were used as responses and analysed according to a mixture design experiment (secondary model). The contour lines of the corresponding response surfaces clearly disclosed the relationships between growth and environmental conditions, showing the stimulating and inhibitory effect of ascorbic acid and sodium metabisulphite, respectively, on both populations of microorganisms. This work opens new possibilities for the potential use of the Quasi-chemical primary model in the study of table olive fermentations. (c) 2010 Elsevier B.V. All rights reserved.

40 CFR Table 4 to Subpart IIIii of... - Work Practice Standards-Requirements for Mercury Liquid Collection

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Within 4 hours from the time you collect the liquid mercury, you must transfer it from each temporary... 40 Protection of Environment 13 2010-07-01 2010-07-01 false Work Practice Standards-Requirements for Mercury Liquid Collection 4 Table 4 to Subpart IIIII of Part 63 Protection of Environment...

From the Kitchen Table to the Boardroom Table: The Canadian Family and the Work Place.

ERIC Educational Resources Information Center

Vanier Inst. of the Family, Ottawa (Ontario).

This report is intended to increase awareness of the connections between two central spheres of social activity--work and family. Complementing the conventional analyses of the labor force in terms of economic sectors, educational requisites, age and income distribution, the report also presents an analysis of the family circumstances of the…

40 CFR Table 5 to Subpart Nnnnn of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 14 2011-07-01 2011-07-01 false Continuous Compliance With Emission Limitations and Work Practice Standards 5 Table 5 to Subpart NNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR Table 5 to Subpart Nnnnn of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Continuous Compliance With Emission Limitations and Work Practice Standards 5 Table 5 to Subpart NNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR Table 5 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Transfer Operations

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 13 2011-07-01 2011-07-01 false Emission Limits and Work Practice Standards for Transfer Operations 5 Table 5 to Subpart HHHHH of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES ...

40 CFR Table 5 to Subpart Nnnnn of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 15 2014-07-01 2014-07-01 false Continuous Compliance With Emission Limitations and Work Practice Standards 5 Table 5 to Subpart NNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR Table 5 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Transfer Operations

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 14 2013-07-01 2013-07-01 false Emission Limits and Work Practice Standards for Transfer Operations 5 Table 5 to Subpart HHHHH of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES ...

40 CFR Table 5 to Subpart Nnnnn of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 15 2012-07-01 2012-07-01 false Continuous Compliance With Emission Limitations and Work Practice Standards 5 Table 5 to Subpart NNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR Table 5 to Subpart Nnnnn of... - Continuous Compliance With Emission Limitations and Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 15 2013-07-01 2013-07-01 false Continuous Compliance With Emission Limitations and Work Practice Standards 5 Table 5 to Subpart NNNNN of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES...

40 CFR Table 4 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Wastewater Streams

Code of Federal Regulations, 2010 CFR

2010-07-01

... Standards for Wastewater Streams 4 Table 4 to Subpart HHHHH of Part 63 Protection of Environment... Part 63—Emission Limits and Work Practice Standards for Wastewater Streams As required in § 63.8020... your wastewater streams. For each . . . You must . . . 1. Wastewater tank used to store a Group 1...

40 CFR Table 4 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Wastewater Streams

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Wastewater Streams 4 Table 4 to Subpart HHHHH of Part 63 Protection of Environment... Part 63—Emission Limits and Work Practice Standards for Wastewater Streams As required in § 63.8020... your wastewater streams. For each . . . You must . . . 1. Wastewater tank used to store a Group 1...

40 CFR Table 4 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Wastewater Streams

Code of Federal Regulations, 2013 CFR

2013-07-01

... Standards for Wastewater Streams 4 Table 4 to Subpart HHHHH of Part 63 Protection of Environment... Part 63—Emission Limits and Work Practice Standards for Wastewater Streams As required in § 63.8020... your wastewater streams. For each . . . You must . . . 1. Wastewater tank used to store a Group 1...

40 CFR Table 4 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Wastewater Streams

Code of Federal Regulations, 2014 CFR

2014-07-01

... Standards for Wastewater Streams 4 Table 4 to Subpart HHHHH of Part 63 Protection of Environment... Part 63—Emission Limits and Work Practice Standards for Wastewater Streams As required in § 63.8020... your wastewater streams. For each . . . You must . . . 1. Wastewater tank used to store a Group 1...

40 CFR Table 4 to Subpart Hhhhh of... - Emission Limits and Work Practice Standards for Wastewater Streams

Code of Federal Regulations, 2012 CFR

2012-07-01

... Standards for Wastewater Streams 4 Table 4 to Subpart HHHHH of Part 63 Protection of Environment... Part 63—Emission Limits and Work Practice Standards for Wastewater Streams As required in § 63.8020... your wastewater streams. For each . . . You must . . . 1. Wastewater tank used to store a Group 1...

Creation of a master table for checking indication and contraindication of medicine from a knowledge base linked with a thesaurus.

PubMed

Ji, Shanmei; Matsumura, Yasushi; Kuwata, Shigeki; Nakano, Hirohiko; Chen, Yufeng; Teratani, Tadamasa; Zhang, Qiyan; Mineno, Takahiro; Takeda, Hiroshi

2004-12-01

To develop a system for checking indication and contraindication of medicines in prescription order entry system, a master table consisting of the disease names corresponding to the medicines adopted in a hospital is needed. The creation of this table requires a considerable manpower. We developed a Web-based system for constructing a medicine/disease thesaurus and a knowledge base. By authority management of users, this system enables many specialists to create the thesaurus collaboratively without confusion. It supports the creation of a knowledge base using concept names by referring to the thesaurus, which is automatically converted to the check master table. When a disease name or medicine name was added to the thesaurus, the check table was automatically updated. We constructed a thesaurus and a knowledge base in the field of circulatory system disease. The knowledge base linked with the thesaurus proved to be efficient for making the check master table for indication/contraindication of medicines.

An interoperability experiment for sharing hydrological rating tables

NASA Astrophysics Data System (ADS)

Lemon, D.; Taylor, P.; Sheahan, P.

2013-12-01

The increasing demand on freshwater resources is requiring authorities to produce more accurate and timely estimates of their available water. Calculation of continuous time-series of river discharge and storage volumes generally requires rating tables. These approximate relationships between two phenomena, such as river level and discharge, and allow us to produce continuous estimates of a phenomenon that may be impractical or impossible to measure directly. Standardised information models or access mechanisms for rating tables are required to support sharing and exchange of water flow data. An Interoperability Experiment (IE) is underway to test an information model that describes rating tables, the observations made to build these ratings, and river cross-section data. The IE is an initiative of the joint World Meteorological Organisation/Open Geospatial Consortium's Hydrology Domain Working Group (HydroDWG) and the model will be published as WaterML2.0 part 2. Interoperability Experiments (IEs) are low overhead, multiple member projects that are run under the OGC's interoperability program to test existing and emerging standards. The HydroDWG has previously run IEs to test early versions of OGC WaterML2.0 part 1 - timeseries. This IE is focussing on two key exchange scenarios: Sharing rating tables and gauging observations between water agencies. Through the use of standard OGC web services, rating tables and associated data will be made available from water agencies. The (Australian) Bureau of Meteorology will retrieve rating tables on-demand from water authorities, allowing the Bureau to run conversions of data within their own systems. Exposing rating tables and gaugings for online analysis and educational purposes. A web client will be developed to enable exploration and visualization of rating tables, gaugings and related metadata for monitoring points. The client gives a quick view into available rating tables, their periods of applicability and the standard deviation of observations against the relationship. An example of this client running can be seen at the link provided. The result of the IE will form the basis for the standardisation of WaterML2.0 part 2. The use of the standard will lead to increased transparency and accessibility of rating tables, while also improving general understanding of this important hydrological concept.

Effects of leaf area index on the coupling between water table, land surface energy fluxes, and planetary boundary layer at the regional scale

NASA Astrophysics Data System (ADS)

Lu, Y.; Rihani, J.; Langensiepen, M.; Simmer, C.

2013-12-01

Vegetation plays an important role in the exchange of moisture and energy at the land surface. Previous studies indicate that vegetation increases the complexity of the feedbacks between the atmosphere and subsurface through processes such as interception, root water uptake, leaf surface evaporation, and transpiration. Vegetation cover can affect not only the interaction between water table depth and energy fluxes, but also the development of the planetary boundary layer. Leaf Area Index (LAI) is shown to be a major factor influencing these interactions. In this work, we investigate the sensitivity of water table, surface energy fluxes, and atmospheric boundary layer interactions to LAI as a model input. We particularly focus on the role LAI plays on the location and extent of transition zones of strongest coupling and how this role changes over seasonal timescales for a real catchment. The Terrestrial System Modelling Platform (TerrSysMP), developed within the Transregional Collaborative Research Centre 32 (TR32), is used in this study. TerrSysMP consists of the variably saturated groundwater model ParFlow, the land surface model Community Land Model (CLM), and the regional climate and weather forecast model COSMO (COnsortium for Small-scale Modeling). The sensitivity analysis is performed over a range of LAI values for different vegetation types as extracted from the Moderate Resolution Imaging Spectroradiometer (MODIS) dataset for the Rur catchment in Germany. In the first part of this work, effects of vegetation structure on land surface energy fluxes and their connection to water table dynamics are studied using the stand-alone CLM and the coupled subsurface-surface components of TerrSysMP (ParFlow-CLM), respectively. The interconnection between LAI and transition zones of strongest coupling are investigated and analyzed through a subsequent set of subsurface-surface-atmosphere coupled simulations implementing the full TerrSysMP model system.

A survey of visualization systems for network security.

PubMed

Shiravi, Hadi; Shiravi, Ali; Ghorbani, Ali A

2012-08-01

Security Visualization is a very young term. It expresses the idea that common visualization techniques have been designed for use cases that are not supportive of security-related data, demanding novel techniques fine tuned for the purpose of thorough analysis. Significant amount of work has been published in this area, but little work has been done to study this emerging visualization discipline. We offer a comprehensive review of network security visualization and provide a taxonomy in the form of five use-case classes encompassing nearly all recent works in this area. We outline the incorporated visualization techniques and data sources and provide an informative table to display our findings. From the analysis of these systems, we examine issues and concerns regarding network security visualization and provide guidelines and directions for future researchers and visual system developers.

40 CFR Table 7 to Subpart Bbbb of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Monitoring Systems (CEMS) 7 Table 7 to Subpart BBBB of Part 60 Protection of Environment... or Before August 30, 1999 Pt. 60, Subpt. BBBB, Table 7 Table 7 to Subpart BBBB of Part 60—Model Rule... sulfur dioxide emissions of the municipal waste combustion unit 4. Carbon Monoxide 125 percent of the...

40 CFR Table 4 of Subpart Aaaa to... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Monitoring Systems (CEMS) 4 Table 4 of Subpart AAAA to Part 60 Protection of Environment ENVIRONMENTAL.... 60, Subpt. AAAA, Table 4 Table 4 of Subpart AAAA to Part 60—Requirements for Continuous Emission... unit P.S. 2 Method 6C. 4. Carbon Monoxide 125 percent of the maximum expected hourly potential carbon...

40 CFR Table 3 to Subpart Eeee of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Monitoring Systems (CEMS) 3 Table 3 to Subpart EEEE of Part 60 Protection of Environment ENVIRONMENTAL... December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006 Pt. 60, Subpt. EEEE, Table 3 Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring...

40 CFR Table 3 of Subpart Aaaa of... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Monitoring Systems (CEMS) 3 Table 3 of Subpart AAAA of Part 60 Protection of Environment... Definitions What definitions must I know? Pt. 60, Subpt. AAAA, Table 3 Table 3 of Subpart AAAA of Part 60... levels Use the following methods in appendix A of this part to measure oxygen (or carbon dioxide) 1...

40 CFR Table 4 of Subpart Aaaa of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Monitoring Systems (CEMS) 4 Table 4 of Subpart AAAA of Part 60 Protection of Environment ENVIRONMENTAL... Definitions What definitions must I know? Pt. 60, Subpt. AAAA, Table 4 Table 4 of Subpart AAAA of Part 60... dioxide emissions of the municipal waste combustion unit P.S. 2 Method 6C. 4. Carbon Monoxide 125 percent...

40 CFR Table 4 of Subpart Aaaa of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2013 CFR

2013-07-01

... Monitoring Systems (CEMS) 4 Table 4 of Subpart AAAA of Part 60 Protection of Environment ENVIRONMENTAL... Definitions What definitions must I know? Pt. 60, Subpt. AAAA, Table 4 Table 4 of Subpart AAAA of Part 60... dioxide emissions of the municipal waste combustion unit P.S. 2 Method 6C. 4. Carbon Monoxide 125 percent...

40 CFR Table 3 to Subpart Eeee of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Monitoring Systems (CEMS) 3 Table 3 to Subpart EEEE of Part 60 Protection of Environment ENVIRONMENTAL... December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006 Pt. 60, Subpt. EEEE, Table 3 Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring...

40 CFR Table 3 to Subpart Eeee of... - Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2013 CFR

2013-07-01

... Monitoring Systems (CEMS) 3 Table 3 to Subpart EEEE of Part 60 Protection of Environment ENVIRONMENTAL... December 9, 2004, or for Which Modification or Reconstruction is Commenced on or After June 16, 2006 Pt. 60, Subpt. EEEE, Table 3 Table 3 to Subpart EEEE of Part 60—Requirements for Continuous Emission Monitoring...

40 CFR Table 7 to Subpart Bbbb of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Monitoring Systems (CEMS) 7 Table 7 to Subpart BBBB of Part 60 Protection of Environment... or Before August 30, 1999 Pt. 60, Subpt. BBBB, Table 7 Table 7 to Subpart BBBB of Part 60—Model Rule... sulfur dioxide emissions of the municipal waste combustion unit 4. Carbon Monoxide 125 percent of the...

40 CFR Table 3 of Subpart Aaaa to... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Monitoring Systems (CEMS) 3 Table 3 of Subpart AAAA to Part 60 Protection of Environment... SOURCES Pt. 60, Subpt. AAAA, Table 3 Table 3 of Subpart AAAA to Part 60—Requirements for Validating... following methods in appendix A of this part to measure oxygen (or carbon dioxide) 1. Nitrogen Oxides (Class...

40 CFR Table 7 to Subpart Bbbb of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Monitoring Systems (CEMS) 7 Table 7 to Subpart BBBB of Part 60 Protection of Environment... or Before August 30, 1999 Pt. 60, Subpt. BBBB, Table 7 Table 7 to Subpart BBBB of Part 60—Model Rule... sulfur dioxide emissions of the municipal waste combustion unit 4. Carbon Monoxide 125 percent of the...

40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 41 Table 41 to Subpart UUU of Part 63—Requirements for...

40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63... Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 41 Table 41 to Subpart UUU of Part 63...

40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63... Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 41 Table 41 to Subpart UUU of Part 63...

40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63... Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 41 Table 41 to Subpart UUU of Part 63...

Successful Demonstration of New Isolated Bridge System at UCB Shaking Table

Science.gov Websites

other events Successful Demonstration of New Isolated Bridge System at UCB Shaking Table PEER Events Successful Demonstration of New Isolated Bridge System at UCB Shaking Table On May 26, 2010 over 100 demonstration of a new isolated bridge system at the PEER Earthquake Simulator Laboratory at UC Berkeley’s

Evaluation of a local exhaust system used in the manufacture of small parts made of reinforced plastic.

PubMed

Lazure, L P

2000-09-01

Fiber-reinforced plastics are used to manufacture a large variety of products, particularly for the transportation sector. Hand lay-up molding and projection molding are the main methods of manufacture. The users of these processes are exposed to appreciable emissions of styrene; in Quebec, more than 3000 workers work in this industry. A statistical analysis of styrene concentrations measured over a five-year period by the Institut de recherche en santé et en sécurité du travail (IRSST, Occupational Health and Safety Research Institute) reveals that for all of the main manufacturing sectors involved, between 40 percent and 78 percent of the results exceed the exposure standard of 50 ppm. This study evaluated the effectiveness of a ventilated table in controlling worker exposure to styrene and acetone in a shop that manufactures fiber-reinforced plastics parts. The evaluated local extraction system consists of a ventilated table with a surface area of 1.2 m x 1.2 m. During molding, the styrene emissions are exhausted through the ventilated table as well as through the slots in a lateral hood. Replacement air, introduced vertically through a supply air shower located above the worker, limits the diffusion of contaminants toward the worker's breathing zone. The reduction in worker exposure to styrene and acetone during hand lay-up molding was measured in the breathing zone for two sizes of molds. The results show that exhaust ventilation reduced the styrene concentrations by 91 percent and that the introduction of replacement air increased the efficiency of the ventilated table to 96 percent. The evaluation performed indicates that the ventilated table adequately controls worker exposure to styrene and acetone during the molding of small components.

Analyzing Tabular and State-Transition Requirements Specifications in PVS

NASA Technical Reports Server (NTRS)

Owre, Sam; Rushby, John; Shankar, Natarajan

1997-01-01

We describe PVS's capabilities for representing tabular specifications of the kind advocated by Parnas and others, and show how PVS's Type Correctness Conditions (TCCs) are used to ensure certain well-formedness properties. We then show how these and other capabilities of PVS can be used to represent the AND/OR tables of Leveson and the Decision Tables of Sherry, and we demonstrate how PVS's TCCs can expose and help isolate errors in the latter. We extend this approach to represent the mode transition tables of the Software Cost Reduction (SCR) method in an attractive manner. We show how PVS can check these tables for well-formedness, and how PVS's model checking capabilities can be used to verify invariants and reachability properties of SCR requirements specifications, and inclusion relations between the behaviors of different specifications. These examples demonstrate how several capabilities of the PVS language and verification system can be used in combination to provide customized support for specific methodologies for documenting and analyzing requirements. Because they use only the standard capabilities of PVS, users can adapt and extend these customizations to suit their own needs. Those developing dedicated tools for individual methodologies may find these constructions in PVS helpful for prototyping purposes, or as a useful adjunct to a dedicated tool when the capabilities of a full theorem prover are required. The examples also illustrate the power and utility of an integrated general-purpose system such as PVS. For example, there was no need to adapt or extend the PVS model checker to make it work with SCR specifications described using the PVS TABLE construct: the model checker is applicable to any transition relation, independently of the PVS language constructs used in its definition.

40 CFR Table 1 to Subpart Llllll... - Applicability of General Provisions to Subpart LLLLLL

Code of Federal Regulations, 2011 CFR

2011-07-01

... Modacrylic Fibers Production Area Sources Pt. 63, Subpt. LLLLLL, Table 1 Table 1 to Subpart LLLLLL of Part 63... not include opacity or visible emissions standards or require a continuous opacity monitoring system... does not require a continuous opacity monitoring system or continuous emissions monitoring system. 63.9...

40 CFR Table 1 to Subpart Llllll... - Applicability of General Provisions to Subpart LLLLLL

Code of Federal Regulations, 2010 CFR

2010-07-01

... Modacrylic Fibers Production Area Sources Pt. 63, Subpt. LLLLLL, Table 1 Table 1 to Subpart LLLLLL of Part 63... not include opacity or visible emissions standards or require a continuous opacity monitoring system... does not require a continuous opacity monitoring system or continuous emissions monitoring system. 63.9...

Temporal Progression of Visual Injury from Blast Exposure

DTIC Science & Technology

2017-09-01

seen throughout the duration of the study. To correlate experimental blast exposures in rodents to human blast exposures, a computational parametric...software (JMP 10.0, Cary,NC). Descriptive and univariate analyses will first be performed to identify the occurrence of delayed visual system...later). The biostatistician evaluating the retrospective data has completed the descriptive analysis and is working on the multiple regression. Table

Size exclusion chromatographic analysis of refuse-derived fuel for mycotoxins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bicking, M.K.; Kniseley, R.N.

1980-11-01

A Styragel packing material is characterized in several solvent systems by using a series of test solutes and mycotoxins. Differences in interpretation with other work are discussed. Three different separation modes are generated on one stationary phase. An improved separation of mycotoxins from a compilcated matrix results by simultaneously using size exclusion and liquid-liquid partitioning. 4 figures, 3 tables.

Redefining the Australian Army Officer Corps Allocation Process

DTIC Science & Technology

2010-03-01

Allocation Numbers (Model 2) ......................................60 Table 28. 2009 Revised Corps Allocation Overage and Underage (Model 2...characteristics: age, sex , marital status, and length of service. b. organizational characteristics: size of work group, visibility of organization...with minimal alteration to the planned corps allocation numbers. A full list of the corps overages and underages is contained in Table 23. Table

40 CFR Table 2 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Batch Process Vents

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 2 Table 2 to Subpart FFFF... Group 1 batch process vents a. Reduce collective uncontrolled organic HAP emissions from the sum of all... a flare); or Not applicable. b. Reduce collective uncontrolled organic HAP emissions from the sum of...

29 CFR Appendix A to Subpart S of... - Decompression Tables

Code of Federal Regulations, 2010 CFR

2010-07-01

... working period at 20 pounds gauge. Decompression Table No. 1: 20 pounds for 4 hours, total decompression... minutes per pound. Stage 2 (final) elapsed time 40 Total time 43 Example No. 2: 5-hour working period at... pressure p.s.i.g. Working period hours 1/2 1 11/2 2 3 4 5 6 7 8 Over 8 9 to 12 3 3 3 3 3 3 3 3 3 3 3 14 6 6...

HTML 5 Displays for On-Board Flight Systems

NASA Technical Reports Server (NTRS)

Silva, Chandika

2016-01-01

During my Internship at NASA in the summer of 2016, I was assigned to a project which dealt with developing a web-server that would display telemetry and other system data using HTML 5, JavaScript, and CSS. By doing this, it would be possible to view the data across a variety of screen sizes, and establish a standard that could be used to simplify communication and software development between NASA and other countries. Utilizing a web- approach allowed us to add in more functionality, as well as make the displays more aesthetically pleasing for the users. When I was assigned to this project my main task was to first establish communication with the current display server. This display server would output data from the on-board systems in XML format. Once communication was established I was then asked to create a dynamic telemetry table web page that would update its header and change as new information came in. After this was completed, certain minor functionalities were added to the table such as a hide column and filter by system option. This was more for the purpose of making the table more useful for the users, as they can now filter and view relevant data. Finally my last task was to create a graphical system display for all the systems on the space craft. This was by far the most challenging part of my internship as finding a JavaScript library that was both free and contained useful functions to assist me in my task was difficult. In the end I was able to use the JointJs library and accomplish the task. With the help of my mentor and the HIVE lab team, we were able to establish stable communication with the display server. We also succeeded in creating a fully dynamic telemetry table and in developing a graphical system display for the advanced modular power system. Working in JSC for this internship has taught me a lot about coding in JavaScript and HTML 5. I was also introduced to the concept of developing software as a team, and exposed to the different types of programs that are used to simplify team coding such as GitLab. While in JSC, I took full advantage of and attended the lectures that were held here on site. I learned a lot about what it is NASA does and about the interesting projects that are conducted here. One of the lectures I attended was about the selection process and the criteria that is used to select future astronauts for flight missions. This truly had an impact on my future plans as it showed me that this path was a viable option for me. After this internship I plan on completing my undergraduate course work and plan to move on for a masters degree. However, during the time in which I will be completing my masters course work, I would like to apply for the NASA pathways graduate program and, if I am accepted, eventually move on to being a full time civil servant. Working in NASA has not only been enjoyable, but full of information and great experiences that have motivated me to seek a full time employment here in the near future.

Analysis of the IMS Location Accuracy in Northern Eurasia and North America Using Regional and Global Pn Travel-time Tables

NASA Astrophysics Data System (ADS)

United States Calibration Working Group, Russian Federation/

- Joint Research Program of Seismic Calibration of the International Monitoring System (IMS) in Northern Eurasia and North America has been signed by the Nuclear Treaty Programs Office (NTPO), Department of Defense USA, and the Special Monitoring Service (SMS) of the Ministry of Defense, Russian Federation (RF). Under the Program historical data from nuclear and large chemical explosions of known location and shot time, together with appropriate geological and geophysical data, has been used to derive regional Pn/P travel-time tables for seismic event location within the lower 48 States of the USA and the European part of the RF. These travel-time tables are up to 5seconds faster in shields than the IASPEI91 tables, and up to 5seconds slower in the Western USA. Relocation experiments using the regional Pn travel-time curves and surrogate networks for the IMS network generally improved locations for regional seismic events. The distance between true and estimated location (mislocation) was decreased from an average of 18.8km for the IASPEI91 tables to 10.1km for the regional Pn travel-time tables. However, the regional travel-time table approach has limitations caused by travel-time variations inside major tectonic provinces and paths crossing several tectonic provinces with substantially different crustal and upper mantle velocity structure.The RF members of the Calibration Working Group (WG): Colonel Vyacheslav Gordon (chairman); Dr. Prof. Marat Mamsurov, and Dr. Nikolai Vasiliev. The US members of the WG: Dr. Anton Dainty (chairman), Dr. Douglas Baumgardt, Mr. John Murphy, Dr. Robert North, and Dr. Vladislav Ryaboy.

The Aerodynamic Plane Table

NASA Technical Reports Server (NTRS)

Zahm, A F

1924-01-01

This report gives the description and the use of a specially designed aerodynamic plane table. For the accurate and expeditious geometrical measurement of models in an aerodynamic laboratory, and for miscellaneous truing operations, there is frequent need for a specially equipped plan table. For example, one may have to measure truly to 0.001 inch the offsets of an airfoil at many parts of its surface. Or the offsets of a strut, airship hull, or other carefully formed figure may require exact calipering. Again, a complete airplane model may have to be adjusted for correct incidence at all parts of its surfaces or verified in those parts for conformance to specifications. Such work, if but occasional, may be done on a planing or milling machine; but if frequent, justifies the provision of a special table. For this reason it was found desirable in 1918 to make the table described in this report and to equip it with such gauges and measures as the work should require.

Track and mode controller (TMC): a software executive for a high-altitude pointing and tracking experiment

NASA Astrophysics Data System (ADS)

Michnovicz, Michael R.

1997-06-01

A real-time executive has been implemented to control a high altitude pointing and tracking experiment. The track and mode controller (TMC) implements a table driven design, in which the track mode logic for a tracking mission is defined within a state transition diagram (STD). THe STD is implemented as a state transition table in the TMC software. Status Events trigger the state transitions in the STD. Each state, as it is entered, causes a number of processes to be activated within the system. As these processes propagate through the system, the status of key processes are monitored by the TMC, allowing further transitions within the STD. This architecture is implemented in real-time, using the vxWorks operating system. VxWorks message queues allow communication of status events from the Event Monitor task to the STD task. Process commands are propagated to the rest of the system processors by means of the SCRAMNet shared memory network. The system mode logic contained in the STD will autonomously sequence in acquisition, tracking and pointing system through an entire engagement sequence, starting with target detection and ending with aimpoint maintenance. Simulation results and lab test results will be presented to verify the mode controller. In addition to implementing the system mode logic with the STD, the TMC can process prerecorded time sequences of commands required during startup operations. It can also process single commands from the system operator. In this paper, the author presents (1) an overview, in which he describes the TMC architecture, the relationship of an end-to-end simulation to the flight software and the laboratory testing environment, (2) implementation details, including information on the vxWorks message queues and the SCRAMNet shared memory network, (3) simulation results and lab test results which verify the mode controller, and (4) plans for the future, specifically as to how this executive will expedite transition to a fully functional system.

40 CFR Table 6 to Subpart Bbbb of... - Model Rule-Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2014 CFR

2014-07-01

... Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart BBBB of Part 60 Protection of Environment... or Before August 30, 1999 Pt. 60, Subpt. BBBB, Table 6 Table 6 to Subpart BBBB of Part 60—Model Rule... levels Use the following methods in appendix A of this part to measure oxygen (or carbon dioxide) 1...

40 CFR Table 6 to Subpart Bbbb of... - Model Rule-Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2012 CFR

2012-07-01

... Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart BBBB of Part 60 Protection of Environment... or Before August 30, 1999 Pt. 60, Subpt. BBBB, Table 6 Table 6 to Subpart BBBB of Part 60—Model Rule... levels Use the following methods in appendix A of this part to measure oxygen (or carbon dioxide) 1...

40 CFR Table 3 to Subpart Uuu of... - Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units 3 Table 3 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 3 Table 3 to Subpart UUU of Part 63—Continous Monitoring...

40 CFR Table 3 to Subpart Uuu of... - Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units 3 Table 3 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 3 Table 3 to Subpart UUU of Part 63—Continous Monitoring...

40 CFR Table 3 to Subpart Uuu of... - Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Continous Monitoring Systems for Metal HAP Emissions From Catalytic Cracking Units 3 Table 3 to Subpart UUU of Part 63 Protection of... Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 3 Table 3 to Subpart UUU of Part 63—Continous Monitoring...

Working life tables, Bangladesh 1981.

PubMed

Matin, K A

1986-06-01

Data from the 1981 Bangladesh Population Census were used to construct life tables for working men and women. Bangladesh has a dependency burden of 109 dependents to 100 economically active population. Labor force participation rates in 1981 were 74.1/100 population aged 10 years and over for males and 4.3/100 population aged 10 years and over for females. The age-specific economic activity rates provided the essential link in translating life table data to working life table data. It was calculated that a newborn Bangladesh male had a working life expectancy of 37.8 years and an overall life expectancy of 50.0 years; working life expectancy peaks at 44.2 years at 10 years of age. A newborn female has a working life expectancy of 1.8 years and an overall life expectancy of 49.0 years; a maximum working life expectancy of 2.4 years is obtained at 10 years of age. In the period 1962-81, male working life expectancy registered a slight decline at all ages, while female working life expectancy increased by about 6 months for ages up to 30 years. Mortality accounts for a loss of about 10% of gross years of active life in the 10-69-year goups and 20% in the 10-79-year age group. The male working life expectancy values for Bangladesh in 1981 correspond well with those found in India in 1971, Pakistan in 1978, and Sri Lanka in 1971. However, there is wide divergency in terms of female working life expectancy values: such rates were significantly higher in Sri Lanka and India than in Bangladesh up to the age of 30 years, after which point there was little divergence.

Measurements of system sharpness for two digital breast tomosynthesis systems

NASA Astrophysics Data System (ADS)

Marshall, N. W.; Bosmans, H.

2012-11-01

The aim of this work was to propose system sharpness parameters for digital breast tomosynthesis (DBT) systems that include the influence of focus size and focus motion for use in quality assurance protocols. X-ray focus size was measured using a multiple pinhole test object, while detector presampling modulation transfer function (MTF) was measured from projection images of a 10 cm × 10 cm, 1 mm thick steel edge, for the Siemens Inspiration and Hologic Selenia Dimensions DBT systems. The height of the edge above the table was then varied from 1 to 78 mm. The MTF expected from theory for the projection images was calculated from the measured detector MTF, focus size MTF and focus motion MTF and was compared against measured curves. Two methods were used to measure the in-plane MTF in the DBT volume: a tungsten wire of diameter 25 µm and an Al edge 0.2 mm thick, both imaged with a 15 mm thick poly(methyl methacrylate) (PMMA) plate. The in-depth point spread function (PSF) was measured using an angled tungsten wire. The full 3D MTF was estimated with a 0.5 mm diameter aluminium bead held in a 45 mm thick PMMA phantom, with the bead 15 and 65 mm above the table. Inspiration DBT projection images are saved at native detector resolution (85 µm), while the Dimensions re-bins projections to 140 µm pixels (2 × 2 binning); both systems used 2 × 2 binning of projection data before reconstruction. The 50% point for the MTF (MTF0.50) measured in the DBT projection images for the tube-travel direction fell as a function of height above the table from 3.60 to 0.90 mm-1 for the Inspiration system and from 2.50 to 1.20 mm-1 for the Dimensions unit. The maximum deviation of measured MTF0.50 from the calculated value was 13%. MTF0.50 measured in-plane (tube-travel direction) fell as a function of height above the table from 1.66 to 0.97 mm-1 for the Inspiration system and from 2.21 to 1.31 mm-1 for the Dimensions system. The full-width half-maximum for the in-depth PSF was 3.0 and 5.9 mm for the Inspiration and Dimensions systems, respectively. There was no difference in the 3D MTF curves, sectioned in the tube-travel direction, for bead heights of 15 and 65 mm above the table. A 25 µm tungsten wire held within a 15 mm thick PMMA plate was found to be a suitable test object for measurement of in-plane MTF. Evaluation of MTF as a function of height above the table, both in the projection images and in the reconstructed planes, provides important information on the impact of focus size and focus motion on the DBT system's imaging performance.

Measurements of system sharpness for two digital breast tomosynthesis systems.

PubMed

Marshall, N W; Bosmans, H

2012-11-21

The aim of this work was to propose system sharpness parameters for digital breast tomosynthesis (DBT) systems that include the influence of focus size and focus motion for use in quality assurance protocols. X-ray focus size was measured using a multiple pinhole test object, while detector presampling modulation transfer function (MTF) was measured from projection images of a 10 cm × 10 cm, 1 mm thick steel edge, for the Siemens Inspiration and Hologic Selenia Dimensions DBT systems. The height of the edge above the table was then varied from 1 to 78 mm. The MTF expected from theory for the projection images was calculated from the measured detector MTF, focus size MTF and focus motion MTF and was compared against measured curves. Two methods were used to measure the in-plane MTF in the DBT volume: a tungsten wire of diameter 25 µm and an Al edge 0.2 mm thick, both imaged with a 15 mm thick poly(methyl methacrylate) (PMMA) plate. The in-depth point spread function (PSF) was measured using an angled tungsten wire. The full 3D MTF was estimated with a 0.5 mm diameter aluminium bead held in a 45 mm thick PMMA phantom, with the bead 15 and 65 mm above the table. Inspiration DBT projection images are saved at native detector resolution (85 µm), while the Dimensions re-bins projections to 140 µm pixels (2 × 2 binning); both systems used 2 × 2 binning of projection data before reconstruction. The 50% point for the MTF (MTF(0.50)) measured in the DBT projection images for the tube-travel direction fell as a function of height above the table from 3.60 to 0.90 mm(-1) for the Inspiration system and from 2.50 to 1.20 mm(-1) for the Dimensions unit. The maximum deviation of measured MTF(0.50) from the calculated value was 13%. MTF(0.50) measured in-plane (tube-travel direction) fell as a function of height above the table from 1.66 to 0.97 mm(-1) for the Inspiration system and from 2.21 to 1.31 mm(-1) for the Dimensions system. The full-width half-maximum for the in-depth PSF was 3.0 and 5.9 mm for the Inspiration and Dimensions systems, respectively. There was no difference in the 3D MTF curves, sectioned in the tube-travel direction, for bead heights of 15 and 65 mm above the table. A 25 µm tungsten wire held within a 15 mm thick PMMA plate was found to be a suitable test object for measurement of in-plane MTF. Evaluation of MTF as a function of height above the table, both in the projection images and in the reconstructed planes, provides important information on the impact of focus size and focus motion on the DBT system's imaging performance.

Table Extraction from Web Pages Using Conditional Random Fields to Extract Toponym Related Data

NASA Astrophysics Data System (ADS)

Luthfi Hanifah, Hayyu'; Akbar, Saiful

2017-01-01

Table is one of the ways to visualize information on web pages. The abundant number of web pages that compose the World Wide Web has been the motivation of information extraction and information retrieval research, including the research for table extraction. Besides, there is a need for a system which is designed to specifically handle location-related information. Based on this background, this research is conducted to provide a way to extract location-related data from web tables so that it can be used in the development of Geographic Information Retrieval (GIR) system. The location-related data will be identified by the toponym (location name). In this research, a rule-based approach with gazetteer is used to recognize toponym from web table. Meanwhile, to extract data from a table, a combination of rule-based approach and statistical-based approach is used. On the statistical-based approach, Conditional Random Fields (CRF) model is used to understand the schema of the table. The result of table extraction is presented on JSON format. If a web table contains toponym, a field will be added on the JSON document to store the toponym values. This field can be used to index the table data in accordance to the toponym, which then can be used in the development of GIR system.

Work and retirement among a cohort of older men in the United States, 1966-1983.

PubMed

Hayward, M D; Grady, W R

1990-08-01

Multivariate increment-decrement working life tables are estimated for a cohort of older men in the United States for the period 1966-1983. The approach taken allows multiple processes to be simultaneously incorporated into a single model, resulting in a more realistic portrayal of a cohort's late-life labor force behavior. In addition, because the life table model is developed from multivariate hazard equations, we identify the effects of sociodemographic characteristics on the potentially complex process by which the labor force career is ended. In contrast to the assumed homogeneity of previous working life table analyses, the present study shows marked differences in labor force mobility and working and nonworking life expectancy according to occupation, class of worker, education, race, and marital status. We briefly discuss the implications of these findings for inequities of access to retirement, private and public pension consumption, and future changes in the retirement process.

Improved numerical solutions for chaotic-cancer-model

NASA Astrophysics Data System (ADS)

Yasir, Muhammad; Ahmad, Salman; Ahmed, Faizan; Aqeel, Muhammad; Akbar, Muhammad Zubair

2017-01-01

In biological sciences, dynamical system of cancer model is well known due to its sensitivity and chaoticity. Present work provides detailed computational study of cancer model by counterbalancing its sensitive dependency on initial conditions and parameter values. Cancer chaotic model is discretized into a system of nonlinear equations that are solved using the well-known Successive-Over-Relaxation (SOR) method with a proven convergence. This technique enables to solve large systems and provides more accurate approximation which is illustrated through tables, time history maps and phase portraits with detailed analysis.

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Emission Limits and Work Practice Standards for Transfer Racks 5 Table 5 to Subpart FFFF of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED)...

Becoming Reactive by Concretization

NASA Technical Reports Server (NTRS)

Prieditis, Armand; Janakiraman, Bhaskar

1992-01-01

One way to build a reactive system is to construct an action table indexed by the current situation or stimulus. The action table describes what course of action to pursue for each situation or stimulus. This paper describes an incremental approach to constructing the action table through achieving goals with a hierarchical search system. These hierarchies are generated with transformations called concretizations, which add constraints to a problem and which can reduce the search space. The basic idea is that an action for a state is looked up in the action table and executed whenever the action table has an entry for that state; otherwise, a path is found to the nearest (cost-wise in a graph with costweighted arcs) state that has a mappring from a state in the next highest hierarchy. For each state along the solution path, the successor state in the path is cached in the action table entry for that state. Without caching, the hierarchical search system can logarithmically reduce search. When the table is complete the system no longer searches: it simply reacts by proceeding to the state listed in the table for each state. Since the cached information is specific only to the nearest state in the next highest hierarchy and not the goal, inter-goal transfer of reactivity is possible. To illustrate our approach, we show how an implemented hierarchical search system can completely reactive.

Constructing increment-decrement life tables.

PubMed

Schoen, R

1975-05-01

A life table model which can recognize increments (or entrants) as well as decrements has proven to be of considerable value in the analysis of marital status patterns, labor force participation patterns, and other areas of substantive interest. Nonetheless, relatively little work has been done on the methodology of increment-decrement (or combined) life tables. The present paper reviews the general, recursive solution of Schoen and Nelson (1974), develops explicit solutions for three cases of particular interest, and compares alternative approaches to the construction of increment-decrement tables.

Proposed Methodology for Application of Human-like gradual Multi-Agent Q-Learning (HuMAQ) for Multi-robot Exploration

NASA Astrophysics Data System (ADS)

Narayan Ray, Dip; Majumder, Somajyoti

2014-07-01

Several attempts have been made by the researchers around the world to develop a number of autonomous exploration techniques for robots. But it has been always an important issue for developing the algorithm for unstructured and unknown environments. Human-like gradual Multi-agent Q-leaming (HuMAQ) is a technique developed for autonomous robotic exploration in unknown (and even unimaginable) environments. It has been successfully implemented in multi-agent single robotic system. HuMAQ uses the concept of Subsumption architecture, a well-known Behaviour-based architecture for prioritizing the agents of the multi-agent system and executes only the most common action out of all the different actions recommended by different agents. Instead of using new state-action table (Q-table) each time, HuMAQ uses the immediate past table for efficient and faster exploration. The proof of learning has also been established both theoretically and practically. HuMAQ has the potential to be used in different and difficult situations as well as applications. The same architecture has been modified to use for multi-robot exploration in an environment. Apart from all other existing agents used in the single robotic system, agents for inter-robot communication and coordination/ co-operation with the other similar robots have been introduced in the present research. Current work uses a series of indigenously developed identical autonomous robotic systems, communicating with each other through ZigBee protocol.

Telemetric measurement system of beehive environment conditions

NASA Astrophysics Data System (ADS)

Walendziuk, Wojciech; Sawicki, Aleksander

2014-11-01

This work presents a measurement system of beehive environmental conditions. The purpose of the device is to perform measurements of parameters such as ambient temperature, atmospheric pressure, internal temperature, humidity and sound level. The measured values were transferred to the MySQL database, which is located on an external server, with the use of GPRS protocol. A website presents the measurement data in the form of tables and graphs. The study also shows exemplary results of environmental conditions measurements recorded in the beehive by hour cycle.

The INPE handouts to the 6th LANDSAT Technical Working Group (LTWG) Meeting

NASA Technical Reports Server (NTRS)

Debarrosaguirre, J. L. (Principal Investigator); Parada, L. E. M.; Depaulapereira, S.

1984-01-01

LANDSAT receiving and processing system in its present configuration and status are described, as well as the experience already obtained with LANDSATs 4 and 5. The revised table of station plans for TM reception and products and of implementation schedule for data formats employing superstructure conventions is updated. Standardization of the worldwide reference systems is proposed. The INPE preliminary TM products price list is included. A TM image received and processed is shown to illustrate the appearance of the products offered.

Nofoam System Technology for Aircraft Hangar Fire Suppression Foam System

DTIC Science & Technology

2011-07-01

use of a firefighting agent that meets Military Specification MIL - F - 24385 [Reference 2]. Significant amounts of AFFF wastewater is generated...rates, Table 3, were the established baseline for comparison. Table 3 theoretical flow rates were derived from Military Specification MIL - F - 24385 [Reference...flow rates, Table 3, was the established baseline for comparison. Table 3 theoretical flow rates were derived from Military Specification MIL - F - 24385 [Reference

Application Program Interface for the Orion Aerodynamics Database

NASA Technical Reports Server (NTRS)

Robinson, Philip E.; Thompson, James

2013-01-01

The Application Programming Interface (API) for the Crew Exploration Vehicle (CEV) Aerodynamic Database has been developed to provide the developers of software an easily implemented, fully self-contained method of accessing the CEV Aerodynamic Database for use in their analysis and simulation tools. The API is programmed in C and provides a series of functions to interact with the database, such as initialization, selecting various options, and calculating the aerodynamic data. No special functions (file read/write, table lookup) are required on the host system other than those included with a standard ANSI C installation. It reads one or more files of aero data tables. Previous releases of aerodynamic databases for space vehicles have only included data tables and a document of the algorithm and equations to combine them for the total aerodynamic forces and moments. This process required each software tool to have a unique implementation of the database code. Errors or omissions in the documentation, or errors in the implementation, led to a lengthy and burdensome process of having to debug each instance of the code. Additionally, input file formats differ for each space vehicle simulation tool, requiring the aero database tables to be reformatted to meet the tool s input file structure requirements. Finally, the capabilities for built-in table lookup routines vary for each simulation tool. Implementation of a new database may require an update to and verification of the table lookup routines. This may be required if the number of dimensions of a data table exceeds the capability of the simulation tools built-in lookup routines. A single software solution was created to provide an aerodynamics software model that could be integrated into other simulation and analysis tools. The highly complex Orion aerodynamics model can then be quickly included in a wide variety of tools. The API code is written in ANSI C for ease of portability to a wide variety of systems. The input data files are in standard formatted ASCII, also for improved portability. The API contains its own implementation of multidimensional table reading and lookup routines. The same aerodynamics input file can be used without modification on all implementations. The turnaround time from aerodynamics model release to a working implementation is significantly reduced

Investigating the role of gas bubble formation and entrapment in contaminated aquifers: Reactive transport modelling

USGS Publications Warehouse

Amos, Richard T.; Mayer, K. Ulrich

2006-01-01

In many natural and contaminated aquifers, geochemical processes result in the production or consumption of dissolved gases. In cases where methanogenesis or denitrification occurs, the production of gases may result in the formation and growth of gas bubbles below the water table. Near the water table, entrapment of atmospheric gases during water table rise may provide a significant source of O2 to waters otherwise depleted in O2. Furthermore, the presence of bubbles will affect the hydraulic conductivity of an aquifer, resulting in changes to the groundwater flow regime. The interactions between physical transport, biogeochemical processes, and gas bubble formation, entrapment and release is complex and requires suitable analysis tools. The objective of the present work is the development of a numerical model capable of quantitatively assessing these processes. The multicomponent reactive transport code MIN3P has been enhanced to simulate bubble growth and contraction due to in-situ gas production or consumption, bubble entrapment due to water table rise and subsequent re-equilibration of the bubble with ambient groundwater, and permeability changes due to trapped gas phase saturation. The resulting formulation allows for the investigation of complex geochemical systems where microbially mediated redox reactions both produce and consume gases as well as affect solution chemistry, alkalinity, and pH. The enhanced model has been used to simulate processes in a petroleum hydrocarbon contaminated aquifer where methanogenesis is an important redox process. The simulations are constrained by data from a crude oil spill site near Bemidji, MN. Our results suggest that permeability reduction in the methanogenic zone due to in-situ formation of gas bubbles, and dissolution of entrapped atmospheric bubbles near the water table, both work to attenuate the dissolved gas plume emanating from the source zone. Furthermore, the simulations demonstrate that under the given conditions more than 50% of all produced CH4 partitions to the gas phase or is aerobically oxidised near the water table, suggesting that these processes should be accounted for when assessing the rate and extent of methanogenic degradation of hydrocarbons.

Investigating the role of gas bubble formation and entrapment in contaminated aquifers: Reactive transport modelling

NASA Astrophysics Data System (ADS)

Amos, Richard T.; Ulrich Mayer, K.

2006-09-01

In many natural and contaminated aquifers, geochemical processes result in the production or consumption of dissolved gases. In cases where methanogenesis or denitrification occurs, the production of gases may result in the formation and growth of gas bubbles below the water table. Near the water table, entrapment of atmospheric gases during water table rise may provide a significant source of O 2 to waters otherwise depleted in O 2. Furthermore, the presence of bubbles will affect the hydraulic conductivity of an aquifer, resulting in changes to the groundwater flow regime. The interactions between physical transport, biogeochemical processes, and gas bubble formation, entrapment and release is complex and requires suitable analysis tools. The objective of the present work is the development of a numerical model capable of quantitatively assessing these processes. The multicomponent reactive transport code MIN3P has been enhanced to simulate bubble growth and contraction due to in-situ gas production or consumption, bubble entrapment due to water table rise and subsequent re-equilibration of the bubble with ambient groundwater, and permeability changes due to trapped gas phase saturation. The resulting formulation allows for the investigation of complex geochemical systems where microbially mediated redox reactions both produce and consume gases as well as affect solution chemistry, alkalinity, and pH. The enhanced model has been used to simulate processes in a petroleum hydrocarbon contaminated aquifer where methanogenesis is an important redox process. The simulations are constrained by data from a crude oil spill site near Bemidji, MN. Our results suggest that permeability reduction in the methanogenic zone due to in-situ formation of gas bubbles, and dissolution of entrapped atmospheric bubbles near the water table, both work to attenuate the dissolved gas plume emanating from the source zone. Furthermore, the simulations demonstrate that under the given conditions more than 50% of all produced CH 4 partitions to the gas phase or is aerobically oxidised near the water table, suggesting that these processes should be accounted for when assessing the rate and extent of methanogenic degradation of hydrocarbons.

Northeast Florida Regional Sediment Management: Implementation Strategies and Recommendations for Nassau County and Duval County, Florida

DTIC Science & Technology

2016-03-01

51 Figure 21. Mayport beach placement of entrance channel sediment , 1972...................................... 58 Tables Table 1...Entrance Channel dredged sediment placement history by area. ....................... 20 Table 3. Kings Bay Entrance Channel offshore disposal history at...in northeast Florida is beneficial use of sediments dredged from Federal civil works and military navigation channels for shore protection purposes

40 CFR Table 2 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Batch Process Vents

Code of Federal Regulations, 2010 CFR

2010-07-01

...: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 2 Table 2 to Subpart FFFF of Part 63... vents a. Reduce collective uncontrolled organic HAP emissions from the sum of all batch process vents... applicable. b. Reduce collective uncontrolled organic HAP emissions from the sum of all batch process vents...

40 CFR Table 2 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Batch Process Vents

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 2 Table 2 to Subpart FFFF of Part 63... vents a. Reduce collective uncontrolled organic HAP emissions from the sum of all batch process vents... applicable. b. Reduce collective uncontrolled organic HAP emissions from the sum of all batch process vents...

40 CFR Table 1 to Subpart IIIii of... - Work Practice Standards-Design, Operation, and Maintenance Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... Pollutants: Mercury Emissions From Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 1 Table 1 to... . . . 1. Cell rooms a. For new or modified cell rooms, construct each cell room interior using materials... mercury spills or accumulations, and are easy to clean. b. Limit access around and beneath mercury cells...

The kinematics of table tennis racquet: differences between topspin strokes.

PubMed

Bańkosz, Ziemowit; Winiarski, Sławomir

2017-03-01

Studies of shot kinematics in table tennis have not been sufficiently described in the literature. The assessment of the racquet trajectory, its speed and time characteristics makes it possible to emphasize on certain technical elements in the training process in order, for example, to increase strength, speed of rotation or speed of the shot while maintaining its accuracy. The aim of this work was to measure selected kinematic parameters of table tennis racquet during forehand and backhand topspin shots, while considering the differences between these strokes in table tennis. The measurements took place in a certified biomechanical laboratory using a motion analysis system. The study involved 12 female table tennis players in high-level sports training and performance. Each subject had to complete series of six tasks, presenting different varieties of topspin shots. The longest racquet trajectory was related to forehand shots, shots played against a ball with backspin and winner shots. The maximum racquet velocity was precisely in the moment of impact with the ball. The individual of velocity and distance were larger in the direction of the acting force, depending on the individual shot. Changing the type of topspin shot requires changes of time, velocity and primarily distance parameters as well as the direction of the playing racquet. The maximum speed of the racquet occurring at the moment of the impact is probably the most important principle in playing technique. The results can be directly used in improving training of table tennis techniques, especially in the application and use of topspin shots.

Simulation of Tasks Distribution in Horizontally Scalable Management System

NASA Astrophysics Data System (ADS)

Kustov, D.; Sherstneva, A.; Botygin, I.

2016-08-01

This paper presents an imitational model of the task distribution system for the components of territorially-distributed automated management system with a dynamically changing topology. Each resource of the distributed automated management system is represented with an agent, which allows to set behavior of every resource in the best possible way and ensure their interaction. The agent work load imitation was done via service query imitation formed in a system dynamics style using a stream diagram. The query generation took place in the abstract-represented center - afterwards, they were sent to the drive to be distributed to management system resources according to a ranking table.

Dynamic Docking Test System (DDTS) active table computer program NASA Advanced Docking System (NADS)

NASA Technical Reports Server (NTRS)

Gates, R. M.; Jantz, R. E.

1974-01-01

A computer program was developed to describe the three-dimensional motion of the Dynamic Docking Test System active table. The input consists of inertia and geometry data, actuator structural data, forcing function data, hydraulics data, servo electronics data, and integration control data. The output consists of table responses, actuator bending responses, and actuator responses.

Expert Systems, Job Aids, and the Future of Instructional Technology; and Decision Tables, the Poor Person's Answer to "Expert Systems."

ERIC Educational Resources Information Center

Harmon, Paul; Pipe, Peter

1986-01-01

Describes design and presents examples of industrial use of small expert systems and guidelines for choosing problems which lend themselves to small tool solutions. Use of microcomputer facilitated decision tables to diagnose and categorize people, things, and issues is suggested, and development of three decision table formats is described. (MBR)

76 FR 9395 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Filing and Immediate...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-17

... to other venues on the SOLV System routing table, or (ii) check the NASDAQ book first and then route to destinations on the SOLV System routing table.\\3\\ Under the second option, the applicable routing.... \\3\\ As provided in Rule 4758(a)(1)(A), the term ``System routing table'' refers to the proprietary...

Decision tables and rule engines in organ allocation systems for optimal transparency and flexibility.

PubMed

Schaafsma, Murk; van der Deijl, Wilfred; Smits, Jacqueline M; Rahmel, Axel O; de Vries Robbé, Pieter F; Hoitsma, Andries J

2011-05-01

Organ allocation systems have become complex and difficult to comprehend. We introduced decision tables to specify the rules of allocation systems for different organs. A rule engine with decision tables as input was tested for the Kidney Allocation System (ETKAS). We compared this rule engine with the currently used ETKAS by running 11,000 historical match runs and by running the rule engine in parallel with the ETKAS on our allocation system. Decision tables were easy to implement and successful in verifying correctness, completeness, and consistency. The outcomes of the 11,000 historical matches in the rule engine and the ETKAS were exactly the same. Running the rule engine simultaneously in parallel and in real time with the ETKAS also produced no differences. Specifying organ allocation rules in decision tables is already a great step forward in enhancing the clarity of the systems. Yet, using these tables as rule engine input for matches optimizes the flexibility, simplicity and clarity of the whole process, from specification to the performed matches, and in addition this new method allows well controlled simulations. © 2011 The Authors. Transplant International © 2011 European Society for Organ Transplantation.

VizieR Online Data Catalog: Stellar yields and the initial mass function (Molla+, 2015)

NASA Astrophysics Data System (ADS)

Molla, M.; Cavichia, O.; Gavilan, M.; Gibson, B. K.

2017-10-01

These tables give the theoretical chemical evolution models applied for the Milky Way Galaxy (MWG) from the cited paper. Basically give tables 2, 4 of stellar yields used and results of table 6 for the 144 models computed that work. Tables 2 and 4 give the stellar yields q_i(m) and remmnant mass for low and intermediate stars and massive stars, respectively, in a similar format for all authors. Table 6 gives the value of Chi2 for the 144 models computed for MWG using those stellar yields and different Initial Mass Function (see paper). Moreover, we give the table with results of the present time state of the Galactic disk for these 144 models. (12 data files).

'Putting it into words': developing the RCGP competency descriptors to include 'at-risk behaviours'.

PubMed

Jones, Tim; Tracey, Sue

2012-11-01

As part of the Royal College of General Practitioners' (RCGP) arrangements to satisfy the GMC's requirement for Work Place Based Assessment (WPBAs) a range of 12 WPBA competencies was drawn up. Further to this the RCGP produced descriptors of the behaviours that would demonstrate a trainee had gained competence in that area. Recently the RCGP have expanded the rating scale available to educational supervisors at the time of a review to allow for a finding of 'Needs Further Development (NFD) - below expectations'. In the North of Scotland Deanery it has been recognised that a number of trainees are struggling to demonstrate competency in WPBA and to complete training. Reviewing how we could help these trainees and their educational supervisors there was recognition that early identification of these trainees would assist remedial action. Additionally, having reliable indicators of behaviours associated with a trainee in difficulty would aid the assessment of a trainee as 'NFD - below expectations'. Although many reliable descriptors of 'at-risk' behaviour exist, within frameworks and systems for doctors felt to be in difficulty these systems lie outwith the WPBA competency framework. This paper describes the work undertaken in the North of Scotland Deanery to modify the original table of descriptors for the 12 WPBA competencies to include an 'NFD - below expectations'/'at-risk' behaviours column. The descriptors of behaviours associated with trainees in difficulty have been aligned to the 12 WPBA competencies and used to populate the additional column in the descriptor table. The expectation is that the expanded table of descriptors will assist both in early identification of trainees' at-risk behaviours so that formative work can be engaged in at an early stage in an attachment, and also in the objective assessment of a trainee at an educational supervisor's review if they're in difficulties.

Merging Computer Writing & Collaborative Learning: The Role of Space in Room N779.

ERIC Educational Resources Information Center

Moberg, Goran

At Borough of Manhattan Community College in New York City about a dozen teachers teach English composition in a special room (N779): 25 computers along the 4 walls frame the large arena in the center which holds several work tables, each one surrounded by 6 chairs. The room is an eco-system designed for learning about text production. The most…

Network Modeling and Simulation Environment (NEMSE)

DTIC Science & Technology

2012-07-01

the NEMSE program investigated complex emulation techniques and selected compatible emulation techniques for all OSI network stack layers. Other...EMULAB; 2) Completed the selection of compatible emulation techniques that allows working with all layers of the Open System Interconnect ( OSI ...elements table, Figure 3, reconciles the various elements of NEMSE against the OSI stack and other functions. OSI Layer or Function EM UL AB NS 2

Development of an ADP Training Program to Serve the EPA Data Processing Community.

DTIC Science & Technology

1976-07-29

divide, compute , perform and alter statements; data representation and conversion; table processing; and indexed sequential and random access file...processing. The course workshop will include the testing of coded exercises and problems on a computer system. CLASS SIZE: Individualized METHODS/CONDUCT...familiarization with computer concepts will be helpful. OBJECTIVES OF CURRICULUM After completing this course, the student should have developed a working

Detailed requirements document for the Interactive Financial Management System (IFMS), volume 1

NASA Technical Reports Server (NTRS)

Dodson, D. B.

1975-01-01

The detailed requirements for phase 1 (online fund control, subauthorization accounting, and accounts receivable functional capabilities) of the Interactive Financial Management System (IFMS) are described. This includes information on the following: systems requirements, performance requirements, test requirements, and production implementation. Most of the work is centered on systems requirements, and includes discussions on the following processes: resources authority, allotment, primary work authorization, reimbursable order acceptance, purchase request, obligation, cost accrual, cost distribution, disbursement, subauthorization performance, travel, accounts receivable, payroll, property, edit table maintenance, end-of-year, backup input. Other subjects covered include: external systems interfaces, general inquiries, general report requirements, communication requirements, and miscellaneous. Subjects covered under performance requirements include: response time, processing volumes, system reliability, and accuracy. Under test requirements come test data sources, general test approach, and acceptance criteria. Under production implementation come data base establishment, operational stages, and operational requirements.

Contingency Table Browser - prediction of early stage protein structure.

PubMed

Kalinowska, Barbara; Krzykalski, Artur; Roterman, Irena

2015-01-01

The Early Stage (ES) intermediate represents the starting structure in protein folding simulations based on the Fuzzy Oil Drop (FOD) model. The accuracy of FOD predictions is greatly dependent on the accuracy of the chosen intermediate. A suitable intermediate can be constructed using the sequence-structure relationship information contained in the so-called contingency table - this table expresses the likelihood of encountering various structural motifs for each tetrapeptide fragment in the amino acid sequence. The limited accuracy with which such structures could previously be predicted provided the motivation for a more indepth study of the contingency table itself. The Contingency Table Browser is a tool which can visualize, search and analyze the table. Our work presents possible applications of Contingency Table Browser, among them - analysis of specific protein sequences from the point of view of their structural ambiguity.

Reconfigurable work station for a video display unit and keyboard

NASA Technical Reports Server (NTRS)

Shields, Nicholas L. (Inventor); Roe, Fred D., Jr. (Inventor); Fagg, Mary F. (Inventor); Henderson, David E. (Inventor)

1988-01-01

A reconfigurable workstation is described having video, keyboard, and hand operated motion controller capabilities. The workstation includes main side panels between which a primary work panel is pivotally carried in a manner in which the primary work panel may be adjusted and set in a negatively declined or positively inclined position for proper forearm support when operating hand controllers. A keyboard table supports a keyboard in such a manner that the keyboard is set in a positively inclined position with respect to the negatively declined work panel. Various adjustable devices are provided for adjusting the relative declinations and inclinations of the work panels, tables, and visual display panels.

Helping Soldiers Leverage Army Knowledge, Skills, and Abilities in Civilian Jobs

DTIC Science & Technology

2017-01-01

44,100 High school diploma 4 Wind turbine service technicians 3,710 $48,800 High school diploma 4 Table D.1—Continued 139 Lists of Figures and Tables...servicing automotive electrical systems, including wiring harnesses and starting and charging systems; and Table 3.40 Civilian Occupations Recommended

2014-15 System Accountability Report. Appendix: Data Tables

ERIC Educational Resources Information Center

Board of Governors, State University System of Florida, 2016

2016-01-01

This system accountability report provides the Data Tables that are appended to the 2014-2015 accountability report. The data tables include detailed statistical information presented in a tabular format on the following subject matter: (1) Financial Resources; (2) Personnel; (3) Enrollment; (4) Undergraduate Education; (5) Graduate Education; and…

Mining Claim Activity on Federal Land for the Period 1976 through 2003

USGS Publications Warehouse

Causey, J. Douglas

2005-01-01

Previous reports on mining claim records provided information and statistics (number of claims) using data from the U.S. Bureau of Land Management's (BLM) Mining Claim Recordation System. Since that time, BLM converted their mining claim data to the Legacy Repost 2000 system (LR2000). This report describes a process to extract similar statistical data about mining claims from LR2000 data using different software and procedures than were used in the earlier work. A major difference between this process and the previous work is that every section that has a mining claim record is assigned a value. This is done by proportioning a claim between each section in which it is recorded. Also, the mining claim data in this report includes all BLM records, not just the western states. LR2000 mining claim database tables for the United States were provided by BLM in text format and imported into a Microsoft? Access2000 database in January, 2004. Data from two tables in the BLM LR2000 database were summarized through a series of database queries to determine a number that represents active mining claims in each Public Land Survey (PLS) section for each of the years from 1976 to 2002. For most of the area, spatial databases are also provided. The spatial databases are only configured to work with the statistics provided in the non-spatial data files. They are suitable for geographic information system (GIS)-based regional assessments at a scale of 1:100,000 or smaller (for example, 1:250,000).

Some problems of control of dynamical conditions of technological vibrating machines

NASA Astrophysics Data System (ADS)

Kuznetsov, N. K.; Lapshin, V. L.; Eliseev, A. V.

2017-10-01

The possibility of control of dynamical condition of the shakers that are designed for vibration treatment of parts interacting with granular media is discussed. The aim of this article is to develop the methodological basis of technology of creation of mathematical models of shake tables and the development of principles of formation of vibrational fields, estimation of their parameters and control of the structure vibration fields. Approaches to build mathematical models that take into account unilateral constraints, the relationships between elements, with the vibrating surface are developed. Methods intended to construct mathematical model of linear mechanical oscillation systems are used. Small oscillations about the position of static equilibrium are performed. The original method of correction of vibration fields by introduction of the oscillating system additional ties to the structure are proposed. Additional ties are implemented in the form of a mass-inertial device for changing the inertial parameters of the working body of the vibration table by moving the mass-inertial elements. The concept of monitoring the dynamic state of the vibration table based on the original measuring devices is proposed. Estimation for possible changes in dynamic properties is produced. The article is of interest for specialists in the field of creation of vibration technology machines and equipment.

System identification of timber masonry walls using shaking table test

NASA Astrophysics Data System (ADS)

Roy, Timir B.; Guerreiro, Luis; Bagchi, Ashutosh

2017-04-01

Dynamic study is important in order to design, repair and rehabilitation of structures. It has played an important role in the behavior characterization of structures; such as: bridges, dams, high rise buildings etc. There had been substantial development in this area over the last few decades, especially in the field of dynamic identification techniques of structural systems. Frequency Domain Decomposition (FDD) and Time Domain Decomposition are most commonly used methods to identify modal parameters; such as: natural frequency, modal damping and mode shape. The focus of the present research is to study the dynamic characteristics of typical timber masonry walls commonly used in Portugal. For that purpose, a multi-storey structural prototype of such wall has been tested on a seismic shake table at the National Laboratory for Civil Engineering, Portugal (LNEC). Signal processing has been performed of the output response, which is collected from the shaking table experiment of the prototype using accelerometers. In the present work signal processing of the output response, based on the input response has been done in two ways: FDD and Stochastic Subspace Identification (SSI). In order to estimate the values of the modal parameters, algorithms for FDD are formulated and parametric functions for the SSI are computed. Finally, estimated values from both the methods are compared to measure the accuracy of both the techniques.

Towards automatic patient positioning and scan planning using continuously moving table MR imaging.

PubMed

Koken, Peter; Dries, Sebastian P M; Keupp, Jochen; Bystrov, Daniel; Pekar, Vladimir; Börnert, Peter

2009-10-01

A concept is proposed to simplify patient positioning and scan planning to improve ease of use and workflow in MR. After patient preparation in front of the scanner the operator selects the anatomy of interest by a single push-button action. Subsequently, the patient table is moved automatically into the scanner, while real-time 3D isotropic low-resolution continuously moving table scout scanning is performed using patient-independent MR system settings. With a real-time organ identification process running in parallel and steering the scanner, the target anatomy can be positioned fully automatically in the scanner's sensitive volume. The desired diagnostic examination of the anatomy of interest can be planned and continued immediately using the geometric information derived from the acquired 3D data. The concept was implemented and successfully tested in vivo in 12 healthy volunteers, focusing on the liver as the target anatomy. The positioning accuracy achieved was on the order of several millimeters, which turned out to be sufficient for initial planning purposes. Furthermore, the impact of nonoptimal system settings on the positioning performance, the signal-to-noise ratio (SNR), and contrast-to-noise ratio (CNR) was investigated. The present work proved the basic concept of the proposed approach as an element of future scan automation. (c) 2009 Wiley-Liss, Inc.

50 CFR 679.28 - Equipment and operational requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... observer must be able to stand upright and have a work area at least 0.9 m deep in the area in front of the table and scale. (4) Table. The observer sampling station must include a table at least 0.6 m deep, 1.2... Station available on the NMFS Alaska Region Web site at http://www.fakr.noaa.gov. Inspections will be...

Federal Funds for Research and Development: Fiscal Years 1981, 1982, and 1983. Volume XXXI. Detailed Statistical Tables. Surveys of Science Resources Series.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC. Div. of Science Resources Studies.

Detailed statistical tables on federal funds for research and development (R&D) activities are provided in this document. Tables are organized into the following sections: research, development, and R&D plant; R&D- agency, character of work, and performer; total research- agency, performer, and field of science; basic research- agency,…

Federal Funds for Research and Development: Fiscal Years 1983, 1984, and 1985. Volume XXXIII. Detailed Statistical Tables. Surveys of Science Resources Series.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC. Div. of Science Resources Studies.

Detailed statistical tables showing the funding levels of 92 federal agencies for research and development (R&D) are provided in this document. These tables are organized into the following sections: research, development, and R&D plant; R&D agency, character of work, and performer; total basic and applied applied research--agency,…

40 CFR Table 1 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Continuous Process Vents

Code of Federal Regulations, 2010 CFR

2010-07-01

...: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 1 Table 1 to Subpart FFFF of Part 63... vent a. Not applicable i. Reduce emissions of total organic HAP by ≥98 percent by weight or to an outlet process concentration ≤20 ppmv as organic HAP or TOC by venting emissions through a closed-vent...

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Code of Federal Regulations, 2011 CFR

2011-07-01

... Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 5 Table 5 to Subpart FFFF of Part 63—Emission... each . . . You must . . . 1. Group 1 transfer rack a. Reduce emissions of total organic HAP by ≥98 percent by weight or to an outlet concentration ≤20 ppmv as organic HAP or TOC by venting emissions...

40 CFR Table 1 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Continuous Process Vents

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pollutants: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 1 Table 1 to Subpart FFFF... continuous process vent a. Not applicable i. Reduce emissions of total organic HAP by ≥98 percent by weight or to an outlet process concentration ≤20 ppmv as organic HAP or TOC by venting emissions through a...

40 CFR Table 1 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Continuous Process Vents

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Miscellaneous Organic Chemical Manufacturing Pt. 63, Subpt. FFFF, Table 1 Table 1 to Subpart FFFF of Part 63... vent a. Not applicable i. Reduce emissions of total organic HAP by ≥98 percent by weight or to an outlet process concentration ≤20 ppmv as organic HAP or TOC by venting emissions through a closed-vent...

40 CFR Table 9 to Subpart IIIii of... - Required Records for Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 9 Table 9 to Subpart IIIII of Part 63... other deficiency in a cell room floor, pillar, or beam that could cause liquid mercury to become trapped.... f. If you take a cell off line or isolate the leaking equipment, the date and time you take the cell...

Federal Funds for Research and Development. Fiscal Years 1982, 1983, and 1984. Volume XXXII. Detailed Statistical Tables. Surveys of Science Resources Series.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC. Div. of Science Resources Studies.

Detailed statistical tables on federal funds for research and development (R&D) are provided in this document. Tables are organized into the following sections: research, development, and R&D plant; R&D--agency, character of work, and performer; total research--agency, performer, and field of science; basic research--agency, performer,…

40 CFR Table 9 to Subpart IIIii of... - Required Records for Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 9 Table 9 to Subpart IIIII of Part 63... other deficiency in a cell room floor, pillar, or beam that could cause liquid mercury to become trapped.... f. If you take a cell off line or isolate the leaking equipment, the date and time you take the cell...

40 CFR Table 9 to Subpart IIIii of... - Required Records for Work Practice Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mercury Cell Chlor-Alkali Plants Pt. 63, Subpt. IIIII, Table 9 Table 9 to Subpart IIIII of Part 63... other deficiency in a cell room floor, pillar, or beam that could cause liquid mercury to become trapped.... f. If you take a cell off line or isolate the leaking equipment, the date and time you take the cell...

Reference manual for data base on Nevada water-rights permits

USGS Publications Warehouse

Cartier, K.D.; Bauer, E.M.; Farnham, J.L.

1995-01-01

The U.S. Geological Survey and Nevada Division of Water Resources have cooperatively developed and implemented a data-base system for managing water-rights permit information for the State of Nevada. The Water-Rights Permit data base is part of an integrated system of computer data bases using the Ingres Relational Data-Base Manage-ment System, which allows efficient storage and access to water information from the State Engineer's office. The data base contains a main table, three ancillary tables, and five lookup tables, as well as a menu-driven system for entering, updating, and reporting on the data. This reference guide outlines the general functions of the system and provides a brief description of data tables and data-entry screens.

Verification of aerial photo stand volume tables for southeast Alaska.

Treesearch

Theodore S. Setzer; Bert R. Mead

1988-01-01

Aerial photo volume tables are used in the multilevel sampling system of Alaska Forest Inventory and Analysis. These volume tables are presented with a description of the data base and methods used to construct the tables. Volume estimates compiled from the aerial photo stand volume tables and associated ground-measured values are compared and evaluated.

40 CFR Appendix - Tables to Part 132

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 23 2013-07-01 2013-07-01 false Tables to Part 132 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER QUALITY GUIDANCE FOR THE GREAT LAKES SYSTEM Application of part 132 requirements in Great Lakes States and Tribes. Pt. 132, Tables Tables to Part 132 Table 1—Acute Water Quality...

A Validity Review of the Color Company Competition at the United States Naval Academy

DTIC Science & Technology

2006-06-01

Joy of Wading: Leadership and Team Working in Swampy Conditions. The Mental Health Review, 9 (3), 35-41. Polk, C. J. (2003). Effective ...morale question indicated negative effects . Question 3 (The midshipmen chain of command is working hard to make my company the best in the Brigade...49 Table 6. Color Company Designation Effects on Academic Performance .......................................52 Table 7. Brigade Climate Survey

Precision mass measurements of some isotopes of tungsten and mercury for an adjustment to the mass table in the region A = 184 to A = 204

NASA Astrophysics Data System (ADS)

Barillari, Domenico K.

This thesis concerns the precise re-measurement of mass values in the region of the mercury isotopes, such that important discrepancies in the high-mass end of the mass table could be resolved. Scope and contents. Four mass spectroscopic doublets involving a comparison between 201Hg, 199Hg and 183W (and using a chlorocarbon reference) are reported from measurements made with the upgraded Manitoba 11 deflection instrument. The measurements address the problem of a mass table mis-adjustment in the region of the valley of β-stability between the tungsten group and the noble metals. The results, forming a well-closed loop of mass differences, support the earlier results of Kozier [Ko(1977)] regarding the (stable) mercury isotope masses and confirm an approximate 20 μu discrepancy in the mass adjustment of Audi et al [Au(1993)]. A local least- square re-adjustment conducted using these and existing mass table data suggests that the error originates with mass differences pertaining to one or more other nuclide pairs, perhaps 193Ir-192Ir. The work on upgrading the precision voltage supply and potentiometry system of the Manitoba II instrument is also reported, as is a new assessment on the data processing method. (Abstract shortened by UMI.)

Coping Behavior of International Late Adolescent Students in Selected Australian Educational Institutions

PubMed Central

Shahrill, Masitah; Mundia, Lawrence

2014-01-01

Using the Adolescent Coping Scale, ACS (Frydenberg & Lewis, 1993) we surveyed 45 randomly selected foreign adolescents in Australian schools. The coping strategies used most by the participants were: focus on solving the problem; seeking relaxing diversions; focusing on the positive; seeking social support; worry; seeking to belong; investing in close friends; wishful thinking; and keep to self (Table 4). With regard to coping styles, the most widely used was the productive coping followed by non-productive coping while the least used style was reference to others (Table 4). In terms of both genders the four coping strategies used most often were: work hard to achieve; seeking relaxing diversions; focus on solving the problem; and focus on the positive (Table 5). The most noticeable gender difference was the use of the physical recreation coping strategy in which male students engaged more (Fig 1). The usage of four coping strategies (solving problem; work hard; focus on positive; and social support) was higher for students who have been away from family more than once as compared to those who have been away once only while the usage of seeking relaxing diversions was higher for the first timers (Table 6). No significant differences were obtained on the sample’s performance on the ACS subscales by gender (Table 7), frequency of leaving own country (Table 8), country of origin (Table 9), and length of stay in Australia (Table 11). However, foundation students scored significantly higher on the reference to others variable than their secondary school peers (Table 10). We recommended counseling for students with high support needs and further large-scale mixed-methods research to gain additional insights. PMID:24373267

Positioning and Microvibration Control by Electromagnets of an Air Spring Vibration Isolation System

NASA Technical Reports Server (NTRS)

Watanabe, Katsuhide; Cui, Weimin; Haga, Takahide; Kanemitsu, Yoichi; Yano, Kenichi

1996-01-01

Active positioning and microvibration control has been attempted by electromagnets equipped in a bellows-type, air-spring vibration isolation system. Performance tests have been carried out to study the effects. The main components of the system's isolation table were four electromagnetic actuators and controllers. The vibration isolation table was also equipped with six acceleration sensors for detecting microvibration of the table. The electromagnetic actuators were equipped with bellows-type air springs for passive support of the weight of the item placed on the table, with electromagnets for active positioning, as well as for microvibration control, and relative displacement sensors. The controller constituted a relative feedback system for positioning control and an absolute feedback system for vibration isolation control. In the performance test, a 1,490 kg load (net weight of 1,820 kg) was placed on the vibration isolation table, and both the positioning and microvibration control were carried out electromagnetically. Test results revealed that the vibration transmission was reduced by 95%.

40 CFR 1066.220 - Linearity verification for chassis dynamometer systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... dynamometer speed and torque at least as frequently as indicated in Table 1 of § 1066.215. The intent of... linear regression and the linearity criteria specified in Table 1 of this section. (b) Performance requirements. If a measurement system does not meet the applicable linearity criteria in Table 1 of this...

VLBI2010 Receiver Back End Comparison

NASA Technical Reports Server (NTRS)

Petrachenko, Bill

2013-01-01

VLBI2010 requires a receiver back-end to convert analog RF signals from the receiver front end into channelized digital data streams to be recorded or transmitted electronically. The back end functions are typically performed in two steps: conversion of analog RF inputs into IF bands (see Table 2), and conversion of IF bands into channelized digital data streams (see Tables 1a, 1b and 1c). The latter IF systems are now completely digital and generically referred to as digital back ends (DBEs). In Table 2 two RF conversion systems are compared, and in Tables 1a, 1b, and 1c nine DBE systems are compared. Since DBE designs are advancing rapidly, the data in these tables are only guaranteed to be current near the update date of this document.

77 FR 74193 - Request for Information on Edel-Kindwall Caisson Tables for Preventing Decompression Illness in...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-13

... blood or tissues can result in obstruction of blood flow or pressure effects. Clinical manifestations of... Tables,(3) Information on related control measures (e.g., engineering controls, work practices, personal...

Validating Future Force Performance Measures (Army Class): Concluding Analyses

DTIC Science & Technology

2016-06-01

32 Table 3.10. Descriptive Statistics and Intercorrelations for LV Final Predictor Factor Scores...55 Table 4.7. Descriptive Statistics for Analysis Criteria...Soldier attrition and performance: Dependability (Non- Delinquency ), Adjustment, Physical Conditioning, Leadership, Work Orientation, and Agreeableness

27. MASCOT BRICK AUGER AND No 1 COMBINATION CUTTING TABLE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. MASCOT BRICK AUGER AND No 1 COMBINATION CUTTING TABLE MANUFACTURED BY THE AMERICAN CLAY MACHINERY CO. OF BUCYRUS, OHIO. IT WAS PURCHASED IN 1903. AND USED AT THE FIRST MORAVIAN POTTERY AND TILE WORKS BEFORE BEING MOVED TO ITS PRESENT LOCATION IN 1912. IT IS USED TO SCREEN STONES FROM RAW CLAY AND INCORPORATE WATER TO A PROPER WORKING CONSISTENCY. IT IS NOW POWERED BY AN ELECTRIC MOTOR INSTALLED IN 1990. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Evaluating the ergonomics of a student learning environment.

PubMed

Rudolf, Michelle; Griffiths, Yolanda

2009-01-01

Ergonomics is a key consideration of a student-learning environment. This paper examines aspects of ergonomics and application to the design of tables in three classrooms at a Midwestern university. Custom tables with power outlets and Internet access via Ethernet data ports were planned for classrooms in 2000 to facilitate a laptop program. However, table height, specifically thigh clearance from the seat to the bottom of the work surface, was not fully considered. The ergonomic analysis of the classrooms by an occupational therapy student led to the implementation of positive changes to the tables. The enhancement of the learning environment influences student comfort and productivity and can offset the cost of renovating the tables.

Optimizing TLB entries for mixed page size storage in contiguous memory

DOEpatents

Chen, Dong; Gara, Alan; Giampapa, Mark E.; Heidelberger, Philip; Kriegel, Jon K.; Ohmacht, Martin; Steinmacher-Burow, Burkhard

2013-04-30

A system and method for accessing memory are provided. The system comprises a lookup buffer for storing one or more page table entries, wherein each of the one or more page table entries comprises at least a virtual page number and a physical page number; a logic circuit for receiving a virtual address from said processor, said logic circuit for matching the virtual address to the virtual page number in one of the page table entries to select the physical page number in the same page table entry, said page table entry having one or more bits set to exclude a memory range from a page.

The European Southern Observatory-MIDAS table file system

NASA Technical Reports Server (NTRS)

Peron, M.; Grosbol, P.

1992-01-01

The new and substantially upgraded version of the Table File System in MIDAS is presented as a scientific database system. MIDAS applications for performing database operations on tables are discussed, for instance, the exchange of the data to and from the TFS, the selection of objects, the uncertainty joins across tables, and the graphical representation of data. This upgraded version of the TFS is a full implementation of the binary table extension of the FITS format; in addition, it also supports arrays of strings. Different storage strategies for optimal access of very large data sets are implemented and are addressed in detail. As a simple relational database, the TFS may be used for the management of personal data files. This opens the way to intelligent pipeline processing of large amounts of data. One of the key features of the Table File System is to provide also an extensive set of tools for the analysis of the final results of a reduction process. Column operations using standard and special mathematical functions as well as statistical distributions can be carried out; commands for linear regression and model fitting using nonlinear least square methods and user-defined functions are available. Finally, statistical tests of hypothesis and multivariate methods can also operate on tables.

A Working Model for the System Alumina-Magnesia.

DTIC Science & Technology

1983-05-01

Several regions in the resulting diagram appear rather uncertain: the liquidus ’National bureau of StandaTds. JANAF Thermochemical Tables, by D. R. Stull ...Code 131) 1 Naval Ordnance Station, Indian Head (Technical Library) 29 Naval Postgraduate School. Monterey Code 012, Dean of Research (1) Code 06... Dean of Science and Engineering (1) Code 1424. Library - Technical Reports (2) Code 33. Weapons Engineering Program Office (1) Code 61. Chairman

Quality Assurance System. Volume 1. Report (Technology Transfer Program)

DTIC Science & Technology

1980-03-03

WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Surface Warfare Center CD Code 2230 - Design Integration Tools Building...192 Room 128-9500 MacArthur Blvd Bethesda, MD 20817-5700 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS...presented herein. TABLE OF CONTENTS VOLUME I - FINDINGS AND CONCLUSIONS SECTION PARAGRAPH TITLE 1 INTRODUCTION 1.1 Purpose and Scope 1.2 Organization of

On-Line Data Reconstruction in Redundant Disk Arrays.

DTIC Science & Technology

1994-05-01

each sale, - file servers that support a large number of clients with differing work schedules , and * automated teller networks in banking systems...24KB Head scheduling : FIFO User data layout: Sequential in address space of array Disk spindles: Synchronized Table 2.2: Default array parameters for...package and a set of scheduling and queueing routines. 2.3.3. Default workload This dissertation reports on many performance evaluations. In order to

Table-driven configuration and formatting of telemetry data in the Deep Space Network

NASA Technical Reports Server (NTRS)

Manning, Evan

1994-01-01

With a restructured software architecture for telemetry system control and data processing, the NASA/Deep Space Network (DSN) has substantially improved its ability to accommodate a wide variety of spacecraft in an era of 'better, faster, cheaper'. In the new architecture, the permanent software implements all capabilities needed by any system user, and text tables specify how these capabilities are to be used for each spacecraft. Most changes can now be made rapidly, outside of the traditional software development cycle. The system can be updated to support a new spacecraft through table changes rather than software changes, reducing the implementation, test, and delivery cycle for such a change from three months to three weeks. The mechanical separation of the text table files from the program software, with tables only loaded into memory when that mission is being supported, dramatically reduces the level of regression testing required. The format of each table is a different compromise between ease of human interpretation, efficiency of computer interpretation, and flexibility.

Medical Applications of IR Focal Plane Arrays

DTIC Science & Technology

1998-03-15

University of Memphis, USA, E. Wolf, H. Bada C Leffler - University of Tennessee at Memphis, USA, M. Daley ■ University of Memphis, USA A two channel ...optical aperture versus thermal sensitivity at two different resolution settings for an optimized medical IR camera LIST OF TABLES TABLE 1 Advantages...34. Technology Transferred: Through this work, infrared imaging in medicine was exposed to ever-growing audiences. For the first time, the work of the last two

Reference manual for data base on Nevada well logs

USGS Publications Warehouse

Bauer, E.M.; Cartier, K.D.

1995-01-01

The U.S. Geological Survey and Nevada Division of Water Resources are cooperatively using a data base for are cooperatively using a data base for managing well-log information for the State of Nevada. The Well-Log Data Base is part of an integrated system of computer data bases using the Ingres Relational Data-Base Management System, which allows efficient storage and access to water information from the State Engineer's office. The data base contains a main table, two ancillary tables, and nine lookup tables, as well as a menu-driven system for entering, updating, and reporting on the data. This reference guide outlines the general functions of the system and provides a brief description of data tables and data-entry screens.

Flexible Early Warning Systems with Workflows and Decision Tables

NASA Astrophysics Data System (ADS)

Riedel, F.; Chaves, F.; Zeiner, H.

2012-04-01

An essential part of early warning systems and systems for crisis management are decision support systems that facilitate communication and collaboration. Often official policies specify how different organizations collaborate and what information is communicated to whom. For early warning systems it is crucial that information is exchanged dynamically in a timely manner and all participants get exactly the information they need to fulfil their role in the crisis management process. Information technology obviously lends itself to automate parts of the process. We have experienced however that in current operational systems the information logistics processes are hard-coded, even though they are subject to change. In addition, systems are tailored to the policies and requirements of a certain organization and changes can require major software refactoring. We seek to develop a system that can be deployed and adapted to multiple organizations with different dynamic runtime policies. A major requirement for such a system is that changes can be applied locally without affecting larger parts of the system. In addition to the flexibility regarding changes in policies and processes, the system needs to be able to evolve; when new information sources become available, it should be possible to integrate and use these in the decision process. In general, this kind of flexibility comes with a significant increase in complexity. This implies that only IT professionals can maintain a system that can be reconfigured and adapted; end-users are unable to utilise the provided flexibility. In the business world similar problems arise and previous work suggested using business process management systems (BPMS) or workflow management systems (WfMS) to guide and automate early warning processes or crisis management plans. However, the usability and flexibility of current WfMS are limited, because current notations and user interfaces are still not suitable for end-users, and workflows are usually only suited for rigid processes. We show how improvements can be achieved by using decision tables and rule-based adaptive workflows. Decision tables have been shown to be an intuitive tool that can be used by domain experts to express rule sets that can be interpreted automatically at runtime. Adaptive workflows use a rule-based approach to increase the flexibility of workflows by providing mechanisms to adapt workflows based on context changes, human intervention and availability of services. The combination of workflows, decision tables and rule-based adaption creates a framework that opens up new possibilities for flexible and adaptable workflows, especially, for use in early warning and crisis management systems.

The Effect of Alternative Work Schedules (AWS) on Performance During Acquisition Based Testing at the U.S. Army Aberdeen Test Center

DTIC Science & Technology

2014-09-01

profile .............................................................. 11 Table 5. Eastman Kodak company profile...schedules. Company profiles for KPMG LLP, Eastman Kodak and Texas Instruments (TI) are presented in Tables 4–6. Following each profile is a summary of the...and business continuity (Giglio n.d.-a). 2. Case Two A company profile (see Table 5) and case study summary on Eastman Kodak are presented in the

National fire-danger rating system fine-fuel moisture content tables—an Alaskan adaptation.

Treesearch

Richard J. Barney

1969-01-01

Fine-fuel moisture content tables, using dry bulb and dewpoint temperatures as entry data, have been developed for use with the National Fire-Danger Rating System in Alaska. Comparisons have been made which illustrate differences resulting from danger-rating calculations based on these new fine-fuel moisture content tables for the cured, transition, and green...

Light and colour as analytical detection tools: a journey into the periodic table using polyamines to bio-inspired systems as chemosensors.

PubMed

Lodeiro, Carlos; Capelo, José Luis; Mejuto, Juan Carlos; Oliveira, Elisabete; Santos, Hugo M; Pedras, Bruno; Nuñez, Cristina

2010-08-01

This critical review describes some developments on the chemistry of fluorescent and colorimetric molecular probes or chemosensors, based on polyamines and associated compounds having oxygen and/or sulfur as donor atoms. The reported systems are essentially based on some selected published work in this field in the last five years, and in the work developed by the authors from 2000 onwards. Some interesting properties beyond sensing molecules, ions or/and cations by fluorescence, colorimetry as well as by MALDI-TOF MS spectrometry can arise from these systems. A short brief on different examples activated by PET (photoinduced electron transfer), ICT (internal charge transfer) and EET (electronic energy transfer) phenomena will be provided. Finally the introduction of bio-inspired compounds derived from emissive amino acid or short peptide systems and nanoparticle devices to detect metal ions will be reviewed (202 references).

Design of Plant Eco-physiology Monitoring System Based on Embedded Technology

NASA Astrophysics Data System (ADS)

Li, Yunbing; Wang, Cheng; Qiao, Xiaojun; Liu, Yanfei; Zhang, Xinlu

A real time system has been developed to collect plant's growth information comprehensively. Plant eco-physiological signals can be collected and analyzed effectively. The system adopted embedded technology: wireless sensors network collect the eco-physiological information. Touch screen and ARM microprocessor make the system work independently without PC. The system is versatile and all parameters can be set by the touch screen. Sensors' intelligent compensation can be realized in this system. Information can be displayed by either graphically or in table mode. The ARM microprocessor provides the interface to connect with the internet, so the system support remote monitoring and controlling. The system has advantages of friendly interface, flexible construction and extension. It's a good tool for plant's management.

Temperature-controlled airflow ventilation in operating rooms compared with laminar airflow and turbulent mixed airflow.

PubMed

Alsved, M; Civilis, A; Ekolind, P; Tammelin, A; Andersson, A Erichsen; Jakobsson, J; Svensson, T; Ramstorp, M; Sadrizadeh, S; Larsson, P-A; Bohgard, M; Šantl-Temkiv, T; Löndahl, J

2018-02-01

To evaluate three types of ventilation systems for operating rooms with respect to air cleanliness [in colony-forming units (cfu/m 3 )], energy consumption and comfort of working environment (noise and draught) as reported by surgical team members. Two commonly used ventilation systems, vertical laminar airflow (LAF) and turbulent mixed airflow (TMA), were compared with a newly developed ventilation technique, temperature-controlled airflow (T c AF). The cfu concentrations were measured at three locations in an operating room during 45 orthopaedic procedures: close to the wound (<40cm), at the instrument table and peripherally in the room. The operating team evaluated the comfort of the working environment by answering a questionnaire. LAF and T c AF, but not TMA, resulted in less than 10cfu/m 3 at all measurement locations in the room during surgery. Median values of cfu/m 3 close to the wound (250 samples) were 0 for LAF, 1 for T c AF and 10 for TMA. Peripherally in the room, the cfu concentrations were lowest for T c AF. The cfu concentrations did not scale proportionally with airflow rates. Compared with LAF, the power consumption of T c AF was 28% lower and there was significantly less disturbance from noise and draught. T c AF and LAF remove bacteria more efficiently from the air than TMA, especially close to the wound and at the instrument table. Like LAF, the new T c AF ventilation system maintained very low levels of cfu in the air, but T c AF used substantially less energy and provided a more comfortable working environment than LAF. This enables energy savings with preserved air quality. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Knights of the Round-Table.

ERIC Educational Resources Information Center

Teagarden, Jim; Koppes, Peggy

This document describes a classroom learning activity that brings together role playing, learning about the Middle Ages, and working for rewards. In the course of the activity, entitled "Knights of the Round Table," students advance by completing assignments and amassing points. Players move upwards through the beginning or…

Kepler Certified False Positive Table

NASA Technical Reports Server (NTRS)

Bryson, Stephen T.; Batalha, Natalie Marie; Colon, Knicole Dawn; Coughlin, Jeffrey Langer; Haas, Michael R.; Henze, Chris; Huber, Daniel; Morton, Tim; Rowe, Jason Frank; Mullally, Susan Elizabeth;

Method and apparatus for automatically generating airfoil performance tables

NASA Technical Reports Server (NTRS)

van Dam, Cornelis P. (Inventor); Mayda, Edward A. (Inventor); Strawn, Roger Clayton (Inventor)

2006-01-01

One embodiment of the present invention provides a system that facilitates automatically generating a performance table for an object, wherein the object is subject to fluid flow. The system operates by first receiving a description of the object and testing parameters for the object. The system executes a flow solver using the testing parameters and the description of the object to produce an output. Next, the system determines if the output of the flow solver indicates negative density or pressure. If not, the system analyzes the output to determine if the output is converging. If converging, the system writes the output to the performance table for the object.

True 3D display and BeoWulf connectivity

NASA Astrophysics Data System (ADS)

Jannson, Tomasz P.; Kostrzewski, Andrew A.; Kupiec, Stephen A.; Yu, Kevin H.; Aye, Tin M.; Savant, Gajendra D.

2003-09-01

We propose a novel true 3-D display based on holographic optics, called HAD (Holographic Autostereoscopic Display), or Holographic Inverse Look-around and Autostereoscopic Reality (HILAR), its latest generation. It does not require goggles, unlike the state of the art 3-D system which do not work without goggles, and has a table-like 360° look-around capability. Also, novel 3-D image-rendering software, based on Beowulf PC cluster hardware is discussed.

Engineering Investigation of Information Integration Display (IID) Integration with Platform Systems

DTIC Science & Technology

2014-07-01

Chair DRP © Her Majesty the Queen in Right of Canada, as represented by the Minister of National Defence, 2014 © Sa Majesté la Reine (en...Objectives Defence Research and Development Canada (DRDC) Atlantic has conducted a Cognitive Work Analysis (CWA) for key Victoria Class Submarine...tables, were added. The “Virtual Victoria Data Model” (reference [2]), “Assumptions and Specifications Matrix” (reference [3]), and a DRDC Atlantic

Multi-Lingual Deep Neural Networks for Language Recognition

DTIC Science & Technology

2016-08-08

training configurations for the NIST 2011 and 2015 lan- guage recognition evaluations (LRE11 and LRE15). The best per- forming multi-lingual BN-DNN...very ef- fective approach in the NIST 2015 language recognition evaluation (LRE15) open training condition [4, 5]. In this work we evaluate the impact...language are summarized in Table 2. Two language recognition tasks are used for evaluating the multi-lingual bottleneck systems. The first is the NIST

The Shrail: A Comparison of a Novel Attachable Rail System With the Current Deployment Operating Table.

PubMed

Dilday, Joshua; Sirkin, Maxwell R; Wertin, Thomas; Bradley, Frances; Hiles, Jason

The current forward surgical team (FST) operating table is heavy and burdensome and hinders essential movement flexibility. A novel attachable rail system, the Shrail, has been developed to overcome these obstacles. The Shrail turns a North Atlantic Treaty Organization litter into a functional operating table. A local FST compared the assembly of the FST operating table with assembling the Shrail. Device weight, storage space, and assembly space were directly measured and compared. The mean assembly time required for the Shrail was significantly less compared with the operating table (23.36 versus 151.6 seconds; p ≤ .01). The Shrail weighs less (6.80kg versus 73.03kg) and requires less storage space (0.019m3 versus 0.323m3) compared with the current FST operating table. The Shrail provides an FST with a faster, lighter surgical table assembly. For these reasons, it is better suited for the demands of an FST and the implementation of prolonged field care. 2018.

Ecological periodic tables: Killer apps for translational ecology

EPA Science Inventory

The chemical periodic table, the Linnaean system of classification and the Hertzsprung-Russell diagram are information organizing structures that have transformed chemistry, biology and astronomy, respectively. Ecological periodic tables are information organizing structures wit...

[The Relation between the Height of Radiographic Table and Workloads of Radiologic Technologist in General X-ray Examinations].

PubMed

Hattori, Akiko; Mizoguchi, Noriko; Arimura, Hisao; Fukano, Yuuichi; Umezu, Yoshiyuki; Yabuuchi, Hidetake

2015-12-01

Workloads of radiological technologists under different conditions of heights of radiographic table and/or X-ray tube assembly were calculated using a software for preventing musculoskeletal complaint to investigate optimal working environment for general X-ray examinations. In the patient positioning, compressive force of lumbar disc decreased at higher radiographic table within the range of 45-90 cm. On the other hand, workload of the shoulder joint increased with increase in the height of radiographic table. Load of the shoulder joint similarly increased as the height of the X-ray tube assembly increased. Compressive force of lumbar disc reduced by approximately 10-30% as the height ratio of the radiographic table to body height increased by approximately 40%, compared to the lowest table of 45 cm. Muscle load of a 50-years-old woman was approximately double compared to a 30-year-old man, even in the same workload. It is important to keep suitable height of radiographic table for reduction of the workloads of lumbar rather than shoulder joint, because floating-type radiographic table is generally used.

The LIFE Laser Design in Context: A Comparison to the State-of-the-Art

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deri, R J; Bayramian, A J; Erlandson, A C

2011-03-21

The current point design for the LIFE laser leverages decades of solid-state laser development in order to achieve the performance and attributes required for inertial fusion energy. This document provides a brief comparison of the LIFE laser point design to other state-of-the-art solid-state lasers. Table I compares the attributes of the current LIFE laser point design to other systems. the state-of-the-art for single-shot performance at fusion-relevant beamline energies is exemplified by performance observed on the National Ignition Facility. The state-of-the-art for high average power is exemplified by the Northrup Grumman JHPSSL laser. Several items in Table I deal with themore » laser efficiency; a more detailed discussion of efficiency can be found in reference 5. The electrical-to-optical efficiency of the LIFE design exceeds that of reference 4 due to the availability of higher efficiency laser diode pumps (70% vs. {approx}50% used in reference 4). LIFE diode pumps are discussed in greater detail in reference 6. The 'beam steering' state of the art is represented by the deflection device that will be used in the LIFE laser, not a laser system. Inspection of Table I shows that most LIFE laser attributes have already been experimentally demonstrated. The two cases where the LIFE design is somewhat better than prior experimental work do not involve the development of new concepts: beamline power is increased simply by increasing aperture (as demonstrated by the power/aperture comparison in Table I), and efficiency increases are achieved by employing state-of-the-art diode pumps. In conclusion, the attributes anticipated for the LIFE laser are consistent with the demonstrated performance of existing solid-state lasers.« less

Solving the problem of Trans-Genomic Query with alignment tables.

PubMed

Parker, Douglass Stott; Hsiao, Ruey-Lung; Xing, Yi; Resch, Alissa M; Lee, Christopher J

2008-01-01

The trans-genomic query (TGQ) problem--enabling the free query of biological information, even across genomes--is a central challenge facing bioinformatics. Solutions to this problem can alter the nature of the field, moving it beyond the jungle of data integration and expanding the number and scope of questions that can be answered. An alignment table is a binary relationship on locations (sequence segments). An important special case of alignment tables are hit tables ? tables of pairs of highly similar segments produced by alignment tools like BLAST. However, alignment tables also include general binary relationships, and can represent any useful connection between sequence locations. They can be curated, and provide a high-quality queryable backbone of connections between biological information. Alignment tables thus can be a natural foundation for TGQ, as they permit a central part of the TGQ problem to be reduced to purely technical problems involving tables of locations.Key challenges in implementing alignment tables include efficient representation and indexing of sequence locations. We define a location datatype that can be incorporated naturally into common off-the-shelf database systems. We also describe an implementation of alignment tables in BLASTGRES, an extension of the open-source POSTGRESQL database system that provides indexing and operators on locations required for querying alignment tables. This paper also reviews several successful large-scale applications of alignment tables for Trans-Genomic Query. Tables with millions of alignments have been used in queries about alternative splicing, an area of genomic analysis concerning the way in which a single gene can yield multiple transcripts. Comparative genomics is a large potential application area for TGQ and alignment tables.

New Polish occupational health and safety regulations for underwater works.

PubMed

Kot, Jacek; Sićko, Zdzisław

2007-01-01

In Poland, the new regulation of the Ministry of Health on Occupational Health for Underwater Works (dated 2007) pursuant to the Act on Underwater Works (dated 2003) has just been published. It is dedicated for commercial, non-military purposes. It defines health requirements for commercial divers and candidates for divers, medical assessment guide with a list of specific medical tests done on initial and periodical medical examination in order for a diver or a candidate for diver to be recognised fit for work, health surveillance during diving operations, compression and decompression procedures, list of content for medical equipment to be present at any diving place, formal qualifications for physicians conducting medical assessment of divers, requirements for certifications confirming the medical status of divers and candidates for divers. Decompression tables cover divings up to 120 meters of depth using compressed air, oxygen, nitrox and heliox as breathing mixtures. There are also decompression tables for repetitive diving, altitude diving and diving in the high-density waters (mud diving). It this paper, general description of health requirements for divers, as well as decompression tables that are included in the new Regulation on Occupational Health for Underwater Works are presented.

An Overview of Starfish: A Table-Centric Tool for Interactive Synthesis

NASA Technical Reports Server (NTRS)

Tsow, Alex

2008-01-01

Engineering is an interactive process that requires intelligent interaction at many levels. My thesis [1] advances an engineering discipline for high-level synthesis and architectural decomposition that integrates perspicuous representation, designer interaction, and mathematical rigor. Starfish, the software prototype for the design method, implements a table-centric transformation system for reorganizing control-dominated system expressions into high-level architectures. Based on the digital design derivation (DDD) system a designer-guided synthesis technique that applies correctness preserving transformations to synchronous data flow specifications expressed as co- recursive stream equations Starfish enhances user interaction and extends the reachable design space by incorporating four innovations: behavior tables, serialization tables, data refinement, and operator retiming. Behavior tables express systems of co-recursive stream equations as a table of guarded signal updates. Developers and users of the DDD system used manually constructed behavior tables to help them decide which transformations to apply and how to specify them. These design exercises produced several formally constructed hardware implementations: the FM9001 microprocessor, an SECD machine for evaluating LISP, and the SchemEngine, garbage collected machine for interpreting a byte-code representation of compiled Scheme programs. Bose and Tuna, two of DDD s developers, have subsequently commercialized the design derivation methodology at Derivation Systems, Inc. (DSI). DSI has formally derived and validated PCI bus interfaces and a Java byte-code processor; they further executed a contract to prototype SPIDER-NASA's ultra-reliable communications bus. To date, most derivations from DDD and DRS have targeted hardware due to its synchronous design paradigm. However, Starfish expressions are independent of the synchronization mechanism; there is no commitment to hardware or globally broadcast clocks. Though software back-ends for design derivation are limited to the DDD stream-interpreter, targeting synchronous or real-time software is not substantively different from targeting hardware.

A new methodology for vibration error compensation of optical encoders.

PubMed

Lopez, Jesus; Artes, Mariano

2012-01-01

Optical encoders are sensors based on grating interference patterns. Tolerances inherent to the manufacturing process can induce errors in the position accuracy as the measurement signals stand apart from the ideal conditions. In case the encoder is working under vibrations, the oscillating movement of the scanning head is registered by the encoder system as a displacement, introducing an error into the counter to be added up to graduation, system and installation errors. Behavior improvement can be based on different techniques trying to compensate the error from measurement signals processing. In this work a new "ad hoc" methodology is presented to compensate the error of the encoder when is working under the influence of vibration. The methodology is based on fitting techniques to the Lissajous figure of the deteriorated measurement signals and the use of a look up table, giving as a result a compensation procedure in which a higher accuracy of the sensor is obtained.

The Role of Triads in the Evolution of the Periodic Table: Past and Present

NASA Astrophysics Data System (ADS)

Scerri, Eric

2008-04-01

The purpose of this article is to propose a new design for the presentation of the periodic system of the elements. It is a system that highlights the fundamental importance of elements as basic substances rather than elements as simple substances, a distinction that is explained in the article. The proposed table is a variant of the Janet or left-step periodic table. Furthermore the fundamental nature of atomic number triads of elements is put to use in obtaining a new perfect triad by relocating hydrogen among the halogens to give the triad H, F, Cl. The relative virtues of this table, as compared with the medium-long form and the left-step table, are discussed.

Investigation of prefrontal cerebral hemodynamics during quantitative autonomic testing using NIRS (Conference Presentation)

NASA Astrophysics Data System (ADS)

Phillips, Zephaniah; Paik, Seung-Ho; Kim, Yoohwan; Kim, Byung-Jo; Choi, Youngwoon; Kim, Beop-Min

2017-02-01

In this work, we analyzed the clinical applicability of NIRS for use during Quantitative Autonomic Testing (QAT). QAT is a protocol consisting of deep breathing, Valsalva maneuver, and tilt table examination. It is used to diagnose a patient with disorders of the autonomic nervous system (ANS). Disorders of ANS includes orthostatic hyper/hypotension, vasovagal syncope, and postural orthostatic tachycardia syndrome. The results of QAT are typically analyzed with the use of blood pressure and heart rate data, however these metrics may be influenced by factors such as arrhythmia, making the data interpretation and diagnosis difficult for clinicians. We tested our custom built 108-channel NIRS probe on 26 elderly patients during the QAT protocol with various ANS disorders. We found that prefrontal cerebral oxygenation correlated well with blood pressure and heart rate changes for all three tasks, making it a clinically feasible tool for observing ANS functionality. During the Valsalva maneuver, we observed a longer delayed and lower amplitude response of cerebral oxygenation to the prefrontal area in orthostatic intolerant patients. During the tilt table examination, we saw a larger response in cerebral oxygenation and less equal transient cerebral oxygenation during tilt up and tilt down in tilt table examinations that were positive (unhealthy), compared to tilt table examinations that were negative (healthy). Overall, our study showcases NIRS as an enhanced tool for understanding ANS disorders.

NASA Electronic Library System (NELS) database schema, version 1.2

NASA Technical Reports Server (NTRS)

Melebeck, Clovis J.

1991-01-01

The database tables used by NELS version 1.2 are discussed. To provide the current functional capability offered by NELS, nineteen tables were created with ORACLE. Each table lists the ORACLE table name and provides a brief description of the tables intended use or function. The following sections cover four basic categories of tables: NELS object classes, NELS collections, NELS objects, and NELS supplemental tables. Also included in each section is a definition and/or relationship of each field to other fields or tables. The primary key(s) for each table is indicated with a single asterisk (*), while foreign keys are indicated with double asterisks (**). The primary key(s) indicate the key(s) which uniquely identifies a record for that table. The foreign key(s) is used to identify additional information in other table(s) for that record. The two appendices are the command which is used to construct the ORACLE tables for NELS. Appendix A contains the commands which create the tables which are defined in the following sections. Appendix B contains the commands which build the indices for these tables.

Data-Dictionary-Editing Program

NASA Technical Reports Server (NTRS)

Cumming, A. P.

1989-01-01

Access to data-dictionary relations and attributes made more convenient. Data Dictionary Editor (DDE) application program provides more convenient read/write access to data-dictionary table ("descriptions table") via data screen using SMARTQUERY function keys. Provides three main advantages: (1) User works with table names and field names rather than with table numbers and field numbers, (2) Provides online access to definitions of data-dictionary keys, and (3) Provides displayed summary list that shows, for each datum, which data-dictionary entries currently exist for any specific relation or attribute. Computer program developed to give developers of data bases more convenient access to the OMNIBASE VAX/IDM data-dictionary relations and attributes.

Disordered crystals from first principles I: Quantifying the configuration space

NASA Astrophysics Data System (ADS)

Kühne, Thomas D.; Prodan, Emil

2018-04-01

This work represents the first chapter of a project on the foundations of first-principle calculations of the electron transport in crystals at finite temperatures. We are interested in the range of temperatures, where most electronic components operate, that is, room temperature and above. The aim is a predictive first-principle formalism that combines ab-initio molecular dynamics and a finite-temperature Kubo-formula for homogeneous thermodynamic phases. The input for this formula is the ergodic dynamical system (Ω , G , dP) defining the thermodynamic crystalline phase, where Ω is the configuration space for the atomic degrees of freedom, G is the space group acting on Ω and dP is the ergodic Gibbs measure relative to the G-action. The present work develops an algorithmic method for quantifying (Ω , G , dP) from first principles. Using the silicon crystal as a working example, we find the Gibbs measure to be extremely well characterized by a multivariate normal distribution, which can be quantified using a small number of parameters. The latter are computed at various temperatures and communicated in the form of a table. Using this table, one can generate large and accurate thermally-disordered atomic configurations to serve, for example, as input for subsequent simulations of the electronic degrees of freedom.

Changes in vegetative communities and water table dynamics following timber harvesting in small headwater streams

Treesearch

B. Choi; J.C. Dewey; J. A. Hatten; A.W. Ezell; Z. Fan

2012-01-01

In order to better understand the relationship between vegetation communities and water table in the uppermost portions (ephemeral–intermittent streams) of headwater systems, seasonal plot-based field characterizations of vegetation were used in conjunction with monthly water table measurements. Vegetation, soils, and water table data were examined to determine...

Military Retirement: Alternate Final Pay and Cost of Living Indexing

DTIC Science & Technology

2014-06-01

LIST OF TABLES Table 1.  Military Retirement System Multipliers (from DOD Office of the Actuary , 2012...10  Table 2.  Number of Retirees by Rank (from DOD Office of the Actuary , 2012...Expectancy (from DOD Office of the Actuary , 2012) ..23  Table 5.  HI-3 Valuation in Millions of Dollars

40 CFR Table 40 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Opacity Monitoring...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Systems 40 Table 40 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 40 Table 40 to Subpart UUU of Part 63—Requirements for Installation, Operation, and Maintenance of...

40 CFR Table 40 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Opacity Monitoring...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Systems 40 Table 40 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 40 Table 40 to Subpart UUU of Part 63—Requirements for Installation, Operation, and Maintenance of Continuous...

40 CFR Table 40 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Opacity Monitoring...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Systems 40 Table 40 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 40 Table 40 to Subpart UUU of Part 63—Requirements for Installation, Operation, and Maintenance of...

40 CFR Table 40 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Opacity Monitoring...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Systems 40 Table 40 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...: Catalytic Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 40 Table 40 to Subpart UUU of Part 63—Requirements for Installation, Operation, and Maintenance of...

40 CFR Table 40 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Opacity Monitoring...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Systems 40 Table 40 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Cracking Units, Catalytic Reforming Units, and Sulfur Recovery Units Pt. 63, Subpt. UUU, Table 40 Table 40 to Subpart UUU of Part 63—Requirements for Installation, Operation, and Maintenance of Continuous...

Resistance of Navy Shipboard Work Clothing Materials to Extreme Heat.

DTIC Science & Technology

1982-10-01

OCT 82 NCTRR _, 48. SSFED N00140-81CRBA83 / 1p N = L. G1.8 IL 5 111 . 1112.6 MIC.5 IIIIONTE III 1. MICROCOPY RESOLUTION TESI CHART n-WN’ :01 IIA...Final Report - 3 December 1980 RESISTANCE OF NAVY SHIPBOARD WORK CLOTHING to 31 July 1982 MATERIALS TO EXTREME HEAT 6. PERFORMING ORO. REPORT NUMBER 7...to Bilateral Radiant Heat (Tables) Appendix 3 : Heat Transfer from Outerwear Fabrics Exposed 153 to Various Radiant Heat Flux Levels (Tables) Appendix 4

Ceramic Matrix Composite Characterization Under a Combustion and Loading Environment

DTIC Science & Technology

2009-03-01

work showed that the material is sensitive in fatigue to center holes above 84% UTS. Barth Boyer did fatigue and creep testing double edge notched...panel obtained for this test was also used in previous AFIT thesis work by Boyer . It is a 12 in x 12 in panel consisting of an eight harness satin...weave with a [0°/90°] fiber orientation. The panel number is 4569-2. The panel properties obtained by Boyer are in Table 3. 17 Table 3

VizieR Online Data Catalog: Northern bright planet host stars parameters (Sousa+, 2015)

NASA Astrophysics Data System (ADS)

Sousa, S. G.; Santos, N. C.; Mortier, A.; Tsantaki, M.; Adibekyan, V.; Delgado Mena, E.; Israelian, G.; Rojas-Ayala, B.; Neves, V.

2015-03-01

The spectroscopic data were collected between 16 April 2013 and 20 August 2013 with the NARVAL spectrograph located at the 2-meter Bernard Lyot Telescope (@ Pic du Midi). The data was obtained through the Opticon proposal (OPTI- CON2013A027). Table 1 contains the spectroscopic parameters derived with ARES+MOOG for the sample of planet hosts analysed in this work. Table 2 contains the stellar mass and radius estimated for the planet hosts analysed in this work. (2 data files).

Ecological periodic tables: in principle and practice - January 2013

EPA Science Inventory

The chemical periodic table, the Linnaean system of classification and the Hertzsprung-Russell diagram are iconic information organizing structures in chemistry, biology and astronomy, respectively. Ecological periodic tables are information organizing structures for ecology. T...

Bibliography of work on the heterogeneous photocatalytic removal of hazardous compounds from water and air, Update Number 2 to October 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blake, D.M.

1997-01-01

The Solar Industrial Program has developed processes that destroy hazardous substances in or remove them from water and air. The processes of interest in this report are based on the application of heterogeneous photocatalysts, principally titanium dioxide or modifications thereof, but work on other heterogeneous catalysts is included in this compilation. This report continues bibliographies that were published in May, 1994, and October, 1995. The previous reports included 663 and 574 citations, respectively. This update contains an additional 518 references. These were published during the period from June 1995 to October 1996, or are references from prior years that weremore » not included in the previous reports. The work generally focuses on removing hazardous contaminants from air or water to meet environmental or health regulations. This report also references work on properties of semiconductor photocatalysts and applications of photocatalytic chemistry in organic synthesis. This report follows the same organization as the previous publications. The first part provides citations for work done in a few broad categories that are generic to the process. Three tables provide references to work on specific substances. The first table lists organic compounds that are included in various lists of hazardous substances identified by the US Environmental Protection Agency (EPA). The second table lists compounds not included in those categories, but which have been treated in a photocatalytic process. The third table covers inorganic compounds that are on EPA lists of hazardous materials or that have been treated by a photocatalytic process. A short update on companies that are active in providing products or services based on photocatalytic processes is provided.« less

Table screen 360-degree holographic display using circular viewing-zone scanning.

PubMed

Inoue, Tatsuaki; Takaki, Yasuhiro

2015-03-09

A table screen 360-degree holographic display is proposed, with an increased screen size, having an expanded viewing zone over all horizontal directions around the table screen. It consists of a microelectromechanical systems spatial light modulator (MEMS SLM), a magnifying imaging system, and a rotating screen. The MEMS SLM generates hologram patterns at a high frame rate, the magnifying imaging system increases the screen of the MEMS SLM, and the reduced viewing zones are scanned circularly by the rotating screen. The viewing zones are localized to practically realize wavefront reconstruction. An experimental system has been constructed. The generation of 360-degree three-dimensional (3D) images was achieved by scanning 800 reduced and localized viewing zones circularly. The table screen had a diameter of 100 mm, and the frame rate of 3D image generation was 28.4 Hz.

Applications of Formal Methods to Specification and Safety of Avionics Software

NASA Technical Reports Server (NTRS)

Hoover, D. N.; Guaspari, David; Humenn, Polar

1996-01-01

This report treats several topics in applications of formal methods to avionics software development. Most of these topics concern decision tables, an orderly, easy-to-understand format for formally specifying complex choices among alternative courses of action. The topics relating to decision tables include: generalizations fo decision tables that are more concise and support the use of decision tables in a refinement-based formal software development process; a formalism for systems of decision tables with behaviors; an exposition of Parnas tables for users of decision tables; and test coverage criteria and decision tables. We outline features of a revised version of ORA's decision table tool, Tablewise, which will support many of the new ideas described in this report. We also survey formal safety analysis of specifications and software.

Profile of Undergraduate Students: 2007-08. Web Tables. NCES 2010-205

ERIC Educational Resources Information Center

Staklis, Sandra

2010-01-01

These tables provide comprehensive information on undergraduates who were enrolled in U.S. postsecondary institutions during the 2007-08 academic year. Estimates for enrolled students are presented by attendance status, degree program, undergraduate major, average grades, student characteristics, financial aid status and credit card debt, work,…

Salaried and Professional Women: Relevant Statistics. Publication #92-3.

ERIC Educational Resources Information Center

Wilson, Pamela, Ed.

This document contains 29 statistical tables grouped into five sections: "General Statistics,""Occupations and Earnings,""Earnings of Selected Professional Occupations,""Women and Higher Education," and "Family Income and Composition." Among the tables are those that show the following: (1) 1991 annual average U.S. civilian work force by…

Random Fill Cache Architecture (Preprint)

DTIC Science & Technology

2014-10-01

a concrete example, we show how the cache collision attack works to extract the AES encryption keys (e.g., in the OpenSSL implementation of AES). AES...each round are implemented as table lookups for performance reasons. OpenSSL uses ten 1-KB lookup tables, five for encryption and five for decryption

View from the Top

ERIC Educational Resources Information Center

Fulwood, Sam, III

2012-01-01

In an age of increasing pressures on the future workforce, the Presidents' Round Table, a network of African-American community college presidents and chief executives, seeks to meet the demand for supplying and training the next generation of educated employees for the evolving job picture. Among its varied goals, the Round Table works to empower…

An Evaluation of Heat Strain Monitoring Methods for Workers in Encapsulating, Impermeable Protective Clothing

DTIC Science & Technology

1987-05-01

LIST OF TABLES Table Page I Estimation of Energy Expenditure from AIHA Ergonomie Guides for Moderate Work at A Hazardous Waste Site 44... Ergonomie Guide. Am. Ind. Hyg. Assoc. J. 32:560 (1971). 3. Ramsey, J.D. Heat Stress Standard: OSHA’s Advisory Committee

Development of a simulation of the surficial groundwater system for the CONUS

NASA Astrophysics Data System (ADS)

Zell, W.; Sanford, W. E.

2016-12-01

Water resource and environmental managers across the country face a variety of questions involving groundwater availability and/or groundwater transport pathways. Emerging management questions require prediction of groundwater response to changing climate regimes (e.g., how drought-induced water-table recession may degrade near-stream vegetation and result in increased wildfire risks), while existing questions can require identification of current groundwater contributions to surface water (e.g., groundwater linkages between landscape contaminant inputs and receiving streams may help explain in-stream phenomena such as fish intersex). At present, few national-coverage simulation tools exist to help characterize groundwater contributions to receiving streams and predict potential changes in base-flow regimes under changing climate conditions. We will describe the Phase 1 development of a simulation of the water table and shallow groundwater system for the entire CONUS. We use national-scale datasets such as the National Recharge Map and the Map Database for Surficial Materials in the CONUS to develop groundwater flow (MODFLOW) and transport (MODPATH) models that are calibrated against groundwater level and stream elevation data from NWIS and NHD, respectively. Phase 1 includes the development of a national transmissivity map for the surficial groundwater system and examines the impact of model-grid resolution on the simulated steady-state discharge network (and associated recharge areas) and base-flow travel time distributions for different HUC scales. In the course of developing the transmissivity map we show that transmissivity in fractured bedrock systems is dependent on depth to water. Subsequent phases of this work will simulate water table changes at a monthly time step (using MODIS-dependent recharge estimates) and serve as a critical complement to surface-water-focused USGS efforts to provide national coverage hydrologic modeling tools.

42 CFR 102.21 - Smallpox (Vaccinia) Vaccine Injury Table.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of the Table, an autoimmune central nervous system injury. In rare cases, the vaccinia virus is isolated from the central nervous system. Manifestations usually occur abruptly and may include fever... spinal cord (myelitis) such as paralysis or meningismus. Long term central nervous system impairments...

42 CFR 102.21 - Smallpox (Vaccinia) Vaccine Injury Table.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of the Table, an autoimmune central nervous system injury. In rare cases, the vaccinia virus is isolated from the central nervous system. Manifestations usually occur abruptly and may include fever... spinal cord (myelitis) such as paralysis or meningismus. Long term central nervous system impairments...

42 CFR 102.21 - Smallpox (Vaccinia) Vaccine Injury Table.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of the Table, an autoimmune central nervous system injury. In rare cases, the vaccinia virus is isolated from the central nervous system. Manifestations usually occur abruptly and may include fever... spinal cord (myelitis) such as paralysis or meningismus. Long term central nervous system impairments...

42 CFR 102.21 - Smallpox (Vaccinia) Vaccine Injury Table.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of the Table, an autoimmune central nervous system injury. In rare cases, the vaccinia virus is isolated from the central nervous system. Manifestations usually occur abruptly and may include fever... spinal cord (myelitis) such as paralysis or meningismus. Long term central nervous system impairments...

Drone Defense System Architecture for U.S. Navy Strategic Facilities

DTIC Science & Technology

2017-09-01

evaluation and weapons assignment (TEWA) to properly address threats. This report follows a systems engineering process to develop a software architecture...C-UAS requires a central system to connect these new and existing systems. The central system uses data fusion and threat evaluation and weapons...30  Table 6.  Decision Type Descriptions .......................................................................40  Table 7

Do children with obesity have worse table manners? Associations between child table manners, weight status and weight gain.

PubMed

Briones, Naomi F; Cesaro, Robert J; Appugliese, Danielle P; Miller, Alison L; Rosenblum, Katherine L; Pesch, Megan H

2018-06-01

Children with obesity experience stigma stemming from stereotypes, one such stereotype is that people with obesity are "sloppy" or have poor manners. Teaching children "proper table manners" has been proposed as an obesity prevention strategy. Little is known about the association between children's weight status and table manners. To examine correlates of child table manners and to examine the association of child table manners with child obese weight status and prospective change in child body mass index z-score (BMIz). Mother-child dyads (N = 228) participated in a videotaped laboratory eating task with cupcakes. Coding schemes to capture child table manners (making crumbs, chewing with mouth open, getting food on face, shoving food in mouth, slouching, and getting out of seat), and maternal attentiveness to child table manners, were reliably applied. Anthropometrics were measured at baseline and at follow-up two years later. Regression analyses examined the association of participant characteristics with child table manners, as well as the associations of child table manners with child obese weight status, and prospective change in BMIz/year. Predictors of poorer child table manners were younger child age, greater cupcake consumption, and greater maternal attentiveness to child table manners. Poorer child table manners were not associated with child obese (vs. not) weight status, but were associated with a prospective decrease in BMIz/year in children with overweight/obesity. Obesity interventions to improve table manners may be perpetuating unfavorable stereotypes and stigma. Future work investigating these associations is warranted to inform childhood obesity guidelines around table manners. Copyright © 2018 Elsevier Ltd. All rights reserved.

Extraction of Data from a Hospital Information System to Perform Process Mining.

PubMed

Neira, Ricardo Alfredo Quintano; de Vries, Gert-Jan; Caffarel, Jennifer; Stretton, Erin

2017-01-01

The aim of this work is to share our experience in relevant data extraction from a hospital information system in preparation for a research study using process mining techniques. The steps performed were: research definition, mapping the normative processes, identification of tables and fields names of the database, and extraction of data. We then offer lessons learned during data extraction phase. Any errors made in the extraction phase will propagate and have implications on subsequent analyses. Thus, it is essential to take the time needed and devote sufficient attention to detail to perform all activities with the goal of ensuring high quality of the extracted data. We hope this work will be informative for other researchers to plan and execute extraction of data for process mining research studies.

40 CFR Table 3 of Subpart Aaaa to... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Requirements for Validating Continuous Emission Monitoring Systems (CEMS) 3 Table 3 of Subpart AAAA to Part 60 Protection of Environment... Continuous Emission Monitoring Systems (CEMS) For the following continuous emission monitoring systems Use...

40 CFR Table 3 of Subpart Aaaa to... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Requirements for Validating Continuous Emission Monitoring Systems (CEMS) 3 Table 3 of Subpart AAAA to Part 60 Protection of Environment... Continuous Emission Monitoring Systems (CEMS) For the following continuous emission monitoring systems Use...

Testing a satellite automatic nutation control system. [on synchronous meteorological satellite

NASA Technical Reports Server (NTRS)

Hrasiar, J. A.

1974-01-01

Testing of a particular nutation control system for the synchronous meteorological satellite (SMS) is described. The test method and principles are applicable to nutation angle control for other satellites with similar requirements. During its ascent to synchronous orbit, a spacecraft like the SMS spins about its minimum-moment-of-inertia axis. An uncontrolled spacecraft in this state is unstable because torques due to fuel motion increase the nutation angle. However, the SMS is equipped with an automatic nutation control (ANC) system which will keep the nutation angle close to zero. Because correct operation of this system is critical to mission success, it was tested on an air-bearing table. The ANC system was mounted on the three-axis air-bearing table which was scaled to the SMS and equipped with appropriate sensors and thrusters. The table was spun up in an altitude chamber and nutation induced so that table motion simulated spacecraft motion. The ANC system was used to reduce the nutation angle. This dynamic test of the ANC system met all its objectives and provided confidence that the ANC system will control the SMS nutation angle.

Method and system for analyzing and classifying electronic information

DOEpatents

McGaffey, Robert W.; Bell, Michael Allen; Kortman, Peter J.; Wilson, Charles H.

2003-04-29

A data analysis and classification system that reads the electronic information, analyzes the electronic information according to a user-defined set of logical rules, and returns a classification result. The data analysis and classification system may accept any form of computer-readable electronic information. The system creates a hash table wherein each entry of the hash table contains a concept corresponding to a word or phrase which the system has previously encountered. The system creates an object model based on the user-defined logical associations, used for reviewing each concept contained in the electronic information in order to determine whether the electronic information is classified. The data analysis and classification system extracts each concept in turn from the electronic information, locates it in the hash table, and propagates it through the object model. In the event that the system can not find the electronic information token in the hash table, that token is added to a missing terms list. If any rule is satisfied during propagation of the concept through the object model, the electronic information is classified.

Chart of conversion factors: From English to metric system and metric to English system

USGS Publications Warehouse

,

1976-01-01

The conversion factors in the following tables are for conversion of our customary (English) units of measurement to SI*units, and for convenience, reciprocals are shown for converting SI units back to the English system. The first table contains rule-of-thumb figures, useful for "getting the feel" of SI units or mental estimation. The succeeding tables contain factors accurate to 3 or more significant figures. Please refer to known reference volumes for additional accuracy, as well as for factors dealing with other scientific notation involving SI units.

The Development and Implementation of Career Information and Guidance Systems to Enhance Recruitment and Retention of ROTC Cadets for Army Careers

DTIC Science & Technology

1990-07-01

relations, variety, working conditions, cultural identity, physical prowess, and economic security. The measures of reliability were computed for the VS: 1...Prowess, Ability Utilization, and Physical Activity and the lowest scale scores on Cultural Identity, Social Relations, and Prestige. Those with neutral...and Cultural Identity and the lowest scale scores on Physical Prowess, Advancement, and Risk. Table 14 Highest and Lowest Rated Value Scale Dimensions

RIPGIS-NET: a GIS tool for riparian groundwater evapotranspiration in MODFLOW.

PubMed

Ajami, Hoori; Maddock, Thomas; Meixner, Thomas; Hogan, James F; Guertin, D Phillip

2012-01-01

RIPGIS-NET, an Environmental System Research Institute (ESRI's) ArcGIS 9.2/9.3 custom application, was developed to derive parameters and visualize results of spatially explicit riparian groundwater evapotranspiration (ETg), evapotranspiration from saturated zone, in groundwater flow models for ecohydrology, riparian ecosystem management, and stream restoration. Specifically RIPGIS-NET works with riparian evapotranspiration (RIP-ET), a modeling package that works with the MODFLOW groundwater flow model. RIP-ET improves ETg simulations by using a set of eco-physiologically based ETg curves for plant functional subgroups (PFSGs), and separates ground evaporation and plant transpiration processes from the water table. The RIPGIS-NET program was developed in Visual Basic 2005, .NET framework 2.0, and runs in ArcMap 9.2 and 9.3 applications. RIPGIS-NET, a pre- and post-processor for RIP-ET, incorporates spatial variability of riparian vegetation and land surface elevation into ETg estimation in MODFLOW groundwater models. RIPGIS-NET derives RIP-ET input parameters including PFSG evapotranspiration curve parameters, fractional coverage areas of each PFSG in a MODFLOW cell, and average surface elevation per riparian vegetation polygon using a digital elevation model. RIPGIS-NET also provides visualization tools for modelers to create head maps, depth to water table (DTWT) maps, and plot DTWT for a PFSG in a polygon in the Geographic Information System based on MODFLOW simulation results. © 2011, The Author(s). Ground Water © 2011, National Ground Water Association.

How well do testate amoebae transfer functions relate to high-resolution water-table records?

NASA Astrophysics Data System (ADS)

Holden, Joseph; Swindles, Graeme; Raby, Cassandra; Blundell, Antony

2014-05-01

Testate amoebae (TA) community composition records from peat cores are often used to infer past water-table conditions on peatland sites. However, one of the problems is that validation of water-table depths used in such work typically comes from a one-off water-table measurement or a few measurements of water-table depth from the testate amoebae sample extraction point. Furthermore, one value of water-table depth is produced by the transfer function reconstruction, with sample-specific errors generated through a statistical resampling approach. However, we know that water tables fluctuate in peatlands and are dynamic. Traditional TA water-table data may not adequately capture a mean value from a site, and may not account for water-table dynamics (e.g. seasonal or annual variability) that could influence the TA community composition. We analysed automatically logged (at least hourly, mainly 15-min) peatland water-table data from 72 different dipwells located across northern Sweden, Wales and the Pennine region of England. Each location had not been subject to recent management intervention. A suite of characteristics of water-table dynamics for each point were determined. At each point surface samples were extracted and the TA community composition was determined. Our results show that estimated water-table depth based on the TA community transfer functions poorly represents the real mean or median water tables for the study sites. The TA approach does, however, generally identify sites that have water tables that are closer to the surface for a greater proportion of the year compared to sites with deeper water tables for large proportions of the year. However, the traditional TA approach does not differentiate between sites with similar mean (or median) water-table depths yet which have quite different water table variability (e.g. interquartile range). We suggest some ways of improving water-table metrics for use in Holocene peatland hydrology reconstructions.

SAGA: A project to automate the management of software production systems

NASA Technical Reports Server (NTRS)

Campbell, R. H.

1983-01-01

The current work in progress for the SAGA project are described. The highlights of this research are: a parser independent SAGA editor, design for the screen editing facilities of the editor, delivery to NASA of release 1 of Olorin, the SAGA parser generator, personal workstation environment research, release 1 of the SAGA symbol table manager, delta generation in SAGA, requirements for a proof management system, documentation for and testing of the cyber pascal make prototype, a prototype cyber-based slicing facility, a June 1984 demonstration plan, SAGA utility programs, summary of UNIX software engineering support, and theorem prover review.

Systems Biology and Cancer Prevention: All Options on the Table

PubMed Central

Rosenfeld, Simon; Kapetanovic, Izet

2008-01-01

In this paper, we outline the status quo and approaches to further development of the systems biology concepts with focus on applications in cancer prevention science. We discuss the biological aspects of cancer research that are of primary importance in cancer prevention, motivations for their mathematical modeling and some recent advances in computational oncology. We also make an attempt to outline in big conceptual terms the contours of future work aimed at creation of large-scale computational and informational infrastructure for using as a routine tool in cancer prevention science and decision making. PMID:19787092

New PSA high concentration solar furnace SF40

NASA Astrophysics Data System (ADS)

Rodriguez, Jose; Cañadas, Inmaculada; Zarza, Eduardo

2016-05-01

A new solar furnace has been designed and built at Plataforma Solar de Almería. In this work, its main components such as heliostat, concentrator, attenuator and test table, and the method used to align them are described. Other equipment like the auxiliary systems necessary for the solar operation, vacuum chamber and gas system are outlined too. Finally, the thermal characteristics of the focus were measured during a test campaign, where different planes along the optical axis were scanned with a radiometer, and the peak flux was obtained and is presented in the last section of this report.

Hazards/Failure Modes and Effects Analysis MK 1 MOD 0 LSO-HUD Console System.

DTIC Science & Technology

1980-03-24

AsI~f~ ! 127 = 3gc Z Isre -0 -q ~sI I I 𔃻~~~ ~ _ _ 3_______ II! -0udC Z Z’ P4 12 d-U * ~s ’:i~i42 S- 60 -, Uh ~ U3l I OM -C ~ . - U 4~ dcd 8U-q Ali...8 VI SCOPE AND METHODOLOGY OF ANALYSIS ........ 1O FIGURE 1: H/ FMEA /(SSA) WORK SHEET FORMAT ........... 14 APPENDIX A: HAZARD/FAILURE MODES AND...EFFECTS ANALYSIS (H/ FMEA ) -- WORK SHEETS ......... 15(A-O) TABLE: SUBSYSTEM: UNIT I Heads-Up Display Console .............. 17(A-1) UNIT 2 Auxiliary

Application of active magnetic bearings in flexible rotordynamic systems - A state-of-the-art review

NASA Astrophysics Data System (ADS)

Siva Srinivas, R.; Tiwari, R.; Kannababu, Ch.

2018-06-01

In this paper a critical review of literature on applications of Active Magnetic Bearings (AMBs) systems in flexible rotordynamic systems have been presented. AMBs find various applications in rotating machinery; however, this paper mainly focuses on works in vibration suppression and associated with the condition monitoring using AMBs. It briefly introduces reader to the AMB working principle, provides details of various hardware components of a typical rotor-AMB test rig, and presents a background of traditional methods of vibration suppression in flexible rotors and the condition monitoring. It then moves on to summarize the basic features of AMB integrated flexible rotor test rigs available in literature with necessary instrumentation and its main objectives. A couple of lookup tables provide summary of important information of test rigs in papers within the scope of this article. Finally, future directions in AMB research within the paper's scope have been suggested.

Automatic Hidden-Web Table Interpretation by Sibling Page Comparison

NASA Astrophysics Data System (ADS)

Tao, Cui; Embley, David W.

The longstanding problem of automatic table interpretation still illudes us. Its solution would not only be an aid to table processing applications such as large volume table conversion, but would also be an aid in solving related problems such as information extraction and semi-structured data management. In this paper, we offer a conceptual modeling solution for the common special case in which so-called sibling pages are available. The sibling pages we consider are pages on the hidden web, commonly generated from underlying databases. We compare them to identify and connect nonvarying components (category labels) and varying components (data values). We tested our solution using more than 2,000 tables in source pages from three different domains—car advertisements, molecular biology, and geopolitical information. Experimental results show that the system can successfully identify sibling tables, generate structure patterns, interpret tables using the generated patterns, and automatically adjust the structure patterns, if necessary, as it processes a sequence of hidden-web pages. For these activities, the system was able to achieve an overall F-measure of 94.5%.

Predicting Stand and Stock Tables from a Spacing Study in Naturally Regenerated Longleaf Pine

Treesearch

Robert M. Farrar

1985-01-01

A prediction system is presented whereby stand and stock tables are calculated for young natural longleaf pine stands of varying initial density. Tables can be output for stand conditions of 10 to 20 years of age, 300 to 1,500 initial trees per acre (at age lo), and 70 to 80 feet in site index (index age 50). The system also allows one to translate from density...

IMS/Satellite Situation Center report. Predicted orbit plots for Hawkeye 1, 1976

NASA Technical Reports Server (NTRS)

1975-01-01

The predicted orbit plots are shown in three projections. The time period covered by each set of projections is 2 days 1 hour, corresponding approximately to the period of Hawkeye 1. The three coordinate systems used are the Geocentric Solar Ecliptic system (GSE), the Geocentric Solar Magnetospheric system (GSM), and the Solar Magnetic system (SM). For each of the three projections, time ticks and codes are given on the satellite trajectories. The codes are interpreted in the table at the base of each plot. Time is given in the table as year/day/decimal hour. The total time covered by each plot is shown at the bottom of each table, and an additional variable is given in the table for each time tick. For the GSM and SM projection this variable is the geocentric distance to the satellite in earth radii, and for the GSE projection the variable is satellite ecliptic latitude in degrees.

Advances in Geologic Disposal System Modeling and Shale Reference Cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariner, Paul E.; Stein, Emily R.; Frederick, Jennifer M.

The Spent Fuel and Waste Science and Technology (SFWST) Campaign of the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), Office of Fuel Cycle Technology (OFCT) is conducting research and development (R&D) on geologic disposal of spent nuclear fuel (SNF) and high level nuclear waste (HLW). Two high priorities for SFWST disposal R&D are design concept development and disposal system modeling (DOE 2011, Table 6). These priorities are directly addressed in the SFWST Generic Disposal Systems Analysis (GDSA) work package, which is charged with developing a disposal system modeling and analysis capability for evaluating disposal system performance formore » nuclear waste in geologic media (e.g., salt, granite, shale, and deep borehole disposal).« less

Hybrid position and orientation tracking for a passive rehabilitation table-top robot.

PubMed

Wojewoda, K K; Culmer, P R; Gallagher, J F; Jackson, A E; Levesley, M C

2017-07-01

This paper presents a real time hybrid 2D position and orientation tracking system developed for an upper limb rehabilitation robot. Designed to work on a table-top, the robot is to enable home-based upper-limb rehabilitative exercise for stroke patients. Estimates of the robot's position are computed by fusing data from two tracking systems, each utilizing a different sensor type: laser optical sensors and a webcam. Two laser optical sensors are mounted on the underside of the robot and track the relative motion of the robot with respect to the surface on which it is placed. The webcam is positioned directly above the workspace, mounted on a fixed stand, and tracks the robot's position with respect to a fixed coordinate system. The optical sensors sample the position data at a higher frequency than the webcam, and a position and orientation fusion scheme is proposed to fuse the data from the two tracking systems. The proposed fusion scheme is validated through an experimental set-up whereby the rehabilitation robot is moved by a humanoid robotic arm replicating previously recorded movements of a stroke patient. The results prove that the presented hybrid position tracking system can track the position and orientation with greater accuracy than the webcam or optical sensors alone. The results also confirm that the developed system is capable of tracking recovery trends during rehabilitation therapy.

It's A Metric World.

ERIC Educational Resources Information Center

Alabama State Dept. of Education, Montgomery. Div. of Instructional Services.

Topics covered in the first part of this document include eight advantages of the metric system; a summary of metric instruction; the International System of Units (SI) style and usage; metric decimal tables; the metric system; and conversion tables. An alphabetized list of organizations which market metric materials for educators is provided with…

Loblolly Pine Growth and Yield Prediction for Managed West Gulf Plantations

Treesearch

V. Clark Baldwin; D.P. Feduccia

1987-01-01

Complete description, including tables, graphs, computer output, of a growth and yield prediction system providing volume and weight yields in stand and stock table format. An example of system use is given along with information about the computer program, COMPUTE P-LOB, that operates the system.

Data Recovery of Distributed Hash Table with Distributed-to-Distributed Data Copy

NASA Astrophysics Data System (ADS)

Doi, Yusuke; Wakayama, Shirou; Ozaki, Satoshi

To realize huge-scale information services, many Distributed Hash Table (DHT) based systems have been proposed. For example, there are some proposals to manage item-level product traceability information with DHTs. In such an application, each entry of a huge number of item-level IDs need to be available on a DHT. To ensure data availability, the soft-state approach has been employed in previous works. However, this does not scale well against the number of entries on a DHT. As we expect 1010 products in the traceability case, the soft-state approach is unacceptable. In this paper, we propose Distributed-to-Distributed Data Copy (D3C). With D3C, users can reconstruct the data as they detect data loss, or even migrate to another DHT system. We show why it scales well against the number of entries on a DHT. We have confirmed our approach with a prototype. Evaluation shows our approach fits well on a DHT with a low rate of failure and a huge number of data entries.

All Things in Moderation

ERIC Educational Resources Information Center

Malone, Larry; De Lucchi, Linda; Long, Kathy

2004-01-01

Four fourth-grade teachers are bent over a conference table, chins in palms, concentrating on one student's assessment paper. This paper is one of many on the table, organized into several ragged piles. The teachers are discussing nuances of the student's work, trying to reach agreement on the quality of the response. The goal of this careful…

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 2 (2010)--Frequency Tables. Technical Report 71B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2009 cohort Wave 2 (2010) data set.

Characteristics, Control and Treatment of Leachate at Military Installations.

DTIC Science & Technology

1981-02-01

points in the area adjacent to the landfill. Background data can be obtained 61C. W. Thornthwaite and J. R. Wather , "Instructions and Tables for...Development," Public Works, Vol 102, No. 2 (March 1971), pp 77-79. Thornthwaite, C. W., and J. R. Wather , "Instructions and Tables for Computing Potential

Forest statistics for Southwest Mississippi counties - 1994

Treesearch

Joanne L. Faulkner; Andrew J. Hartsell; Jack D. London

1995-01-01

Tabulated results were derived from data obtained during a 1994 forest inventory of southwest Mississippi counties (fig. I). These data are considered preliminary. Field work was conducted from February to august 1994. Core tables 1 through 25 are compatible among forest Inventory and Analysis (FIA) units in the Eastern United States. Supplemental tables 26 through 44...

40 CFR Table 7 to Subpart Eeee of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... equivalent control that meets the requirements in Table 4 to this subpart, item 1.a i. After emptying and... out a leak detection and repair program or equivalent control according to one of the subparts listed... CATEGORIES National Emission Standards for Hazardous Air Pollutants: Organic Liquids Distribution (Non...

40 CFR Table 7 to Subpart Eeee of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... equivalent control that meets the requirements in Table 4 to this subpart, item 1.a i. After emptying and... out a leak detection and repair program or equivalent control according to one of the subparts listed... CATEGORIES National Emission Standards for Hazardous Air Pollutants: Organic Liquids Distribution (Non...

40 CFR 63.745 - Standards: Primer and topcoat application operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... system requirements. Each control system shall reduce the operation's organic HAP and VOC emissions to... control system that meets or exceeds the efficiency data points in Tables 1 and 2 of this section and is... pollution control system that meets or exceeds the efficiency data points in Tables 3 and 4 of this section...

40 CFR 63.745 - Standards: Primer and topcoat application operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... system requirements. Each control system shall reduce the operation's organic HAP and VOC emissions to... control system that meets or exceeds the efficiency data points in Tables 1 and 2 of this section and is... pollution control system that meets or exceeds the efficiency data points in Tables 3 and 4 of this section...

40 CFR 63.745 - Standards: Primer and topcoat application operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... system requirements. Each control system shall reduce the operation's organic HAP and VOC emissions to... control system that meets or exceeds the efficiency data points in Tables 1 and 2 of this section and is... pollution control system that meets or exceeds the efficiency data points in Tables 3 and 4 of this section...

40 CFR 63.745 - Standards: Primer and topcoat application operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... system requirements. Each control system shall reduce the operation's organic HAP and VOC emissions to... control system that meets or exceeds the efficiency data points in Tables 1 and 2 of this section and is... pollution control system that meets or exceeds the efficiency data points in Tables 3 and 4 of this section...

40 CFR 63.745 - Standards: Primer and topcoat application operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... system requirements. Each control system shall reduce the operation's organic HAP and VOC emissions to... control system that meets or exceeds the efficiency data points in Tables 1 and 2 of this section and is... pollution control system that meets or exceeds the efficiency data points in Tables 3 and 4 of this section...

40 CFR Table 6 to Subpart Bbbb of... - Model Rule-Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart BBBB of Part 60 Protection of Environment...—Requirements for Validating Continuous Emission Monitoring Systems (CEMS) For the following continuous emission monitoring systems Use the following methods in appendix A of this part to validate poollutant concentratin...

40 CFR Table 6 to Subpart Bbbb of... - Model Rule-Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2011 CFR

2011-07-01

... Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart BBBB of Part 60 Protection of Environment...—Requirements for Validating Continuous Emission Monitoring Systems (CEMS) For the following continuous emission monitoring systems Use the following methods in appendix A of this part to validate poollutant concentratin...

The Development of a Motor-Free Short-Form of the Wechsler Intelligence Scale for Children-Fifth Edition.

PubMed

Piovesana, Adina M; Harrison, Jessica L; Ducat, Jacob J

2017-12-01

This study aimed to develop a motor-free short-form of the Wechsler Intelligence Scale for Children-Fifth Edition (WISC-V) that allows clinicians to estimate the Full Scale Intelligence Quotients of youths with motor impairments. Using the reliabilities and intercorrelations of six WISC-V motor-free subtests, psychometric methodologies were applied to develop look-up tables for four Motor-free Short-form indices: Verbal Comprehension Short-form, Perceptual Reasoning Short-form, Working Memory Short-form, and a Motor-free Intelligence Quotient. Index-level discrepancy tables were developed using the same methods to allow clinicians to statistically compare visual, verbal, and working memory abilities. The short-form indices had excellent reliabilities ( r = .92-.97) comparable to the original WISC-V. This motor-free short-form of the WISC-V is a reliable alternative for the assessment of intellectual functioning in youths with motor impairments. Clinicians are provided with user-friendly look-up tables, index level discrepancy tables, and base rates, displayed similar to those in the WISC-V manuals to enable interpretation of assessment results.

Ecological periodic tables for nekton and benthic macrofaunal community usage of estuarine habitats Slides

EPA Science Inventory

Ecological periodic tables for nekton and benthic macrofaunal community usage of estuarine habitats Steven P. Ferraro, U.S. Environmental Protection Agency, Newport, OR Background/Questions/Methods The chemical periodic table, the Linnaean system of classification, and the Her...

Study of hydro-saline characteristics of soils a palm grove in basin of Ouargla (Northern Algerian Sahara)

NASA Astrophysics Data System (ADS)

Rezagui, D.; Bouhoun, M. Daddi; Boutoutaou, D.; Djaghoubi, A.

2016-07-01

Saharan soils are often faced with several problems of development, taking account the hydro-edaphic constraints, mainly of hydric types by water table, mechanical by gypso-calcareous crusts and saline by irrigation waters and upwelling of water table. Our work consists in doing a soil characterization of a palm grove in Ouargla in order to study the constraints hydro-halomorphes. The results show that irrigation water by two plies of Senonian and Mioplcène had a high salinity with a value of 2.83 and 5.10 dS.m-1 respectively. The conduct of irrigation is traditional random of submersion type. The palm grove has a poor drainage with a level of water table 156.67±15.71 cm and salinity of 31.37±34.04 dS.m-1. The drains are open type and their maintenance is not regular. This situation of management of irrigation-drainage promotes the upwelling of water table and the waterlogging in soils. The study of soil profiles shows the existence of mechanical obstruction of gypso-calcareous crusts which limit the entrenchment of the date palms and the leaching of salts. Soil salinity is excessive in profiles with a range of 8.98 ± 4.58 dS.m-1. This accumulation of salts is due to the dynamic ascending and descending of salts respectively under the effect of upwelling of water table and leaching by irrigation. The salinization, the upwelling of water table and the presence of gypso-calcareous crusts recorded in Ouargla testify to a degradation hydro-halomorphe and mechanic of soil which constitute the major constraints in the management of system irrigation-drainage and sustainable agricultural development of the palm groves of the basin of Ouargla. Some hydro-agricultural planning are necessary to apply in the oasis to improve the hydro-mechanical properties of soils in order to reduce their degradation.

An ergonomic study of the optimum operating table height for laparoscopic surgery.

PubMed

Berquer, R; Smith, W D; Davis, S

2002-03-01

Laparoscopic surgery requires the use of longer instruments than open surgery, thus changing the relation between the height of the surgeon's hands and the desirable height of the operating room table. The optimum height of the operating room table for laparoscopic surgery is investigated in this study. Twenty-one surgeons performed a two-handed, one-fourth circle cutting task using a laparoscopic video system and laparoscopic instruments positioned at five instrument handle heights relative to subjects' elbow height (-20, -10, 0, +10, and +20 cm) by adjusting the height of the trainer box. Subjects rated the difficulty and discomfort experienced during each task on a visual analog scale. Skin conductance (SC) was measured in Micromhos via paired surface electrodes placed near the ulnar edge of the palm of the right (cutting) hand. The mean electromyographic (EMG) signal from the right deltoid and trapezius muscles was measured. Arm orientation was measured in three dimensions using a magnetometer/accelerometer. Signals were acquired using analog circuitry and digitally sampled using a National Instruments DAQCard 700 connected to a Macintosh PowerBook 5300c running LabVIEW software. Statistical analysis was carried out by analysis of variance and post hoc testing. Statistically significant changes were found in the subjective rating of discomfort (p <0.002), deltoid EMG (p <0.0006), trapezius EMG (p <0.0001), and arm elevation (p <0.0001) between instrument handle heights. SC values and task times did not change significantly. Discomfort and difficulty ratings were lowest when instrument handles were positioned at elbow height. EMG values and arm elevation all decreased with lower instrument height. This study suggests that the optimum table height for laparoscopic surgery should position the laparoscopic instrument handles close to surgeons' elbow level to minimize discomfort and upper arm and shoulder muscle work. This corresponds to an approximate table height of 64 to 77 cm above floor level. A redesign of current operating room tables may be required to meet these ergonomic guidelines.

Skin dose mapping for fluoroscopically guided interventions.

PubMed

Johnson, Perry B; Borrego, David; Balter, Stephen; Johnson, Kevin; Siragusa, Daniel; Bolch, Wesley E

2011-10-01

To introduce a new skin dose mapping software system for interventional fluoroscopy dose assessment and to analyze the benefits and limitations of patient-phantom matching. In this study, a new software system was developed for visualizing patient skin dose during interventional fluoroscopy procedures. The system works by translating the reference point air kerma to the location of the patient's skin, which is represented by a computational model. In order to orient the model with the x-ray source, geometric parameters found within the radiation dose structured report (RDSR) are used along with a limited number of in-clinic measurements. The output of the system is a visual indication of skin dose mapped onto an anthropomorphic model at a resolution of 5 mm. In order to determine if patient-dependent and patient-sculpted models increase accuracy, peak skin dose was calculated for each of 26 patient-specific models and compared with doses calculated using an elliptical stylized model, a reference hybrid model, a matched patient-dependent model and one patient-sculpted model. Results were analyzed in terms of a percent difference using the doses calculated using the patient-specific model as the true standard. Anthropometric matching, including the use of both patient-dependent and patient-sculpted phantoms, was shown most beneficial for left lateral and anterior-posterior projections. In these cases, the percent difference using a reference model was between 8 and 20%, using a patient-dependent model between 7 and 15%, and using a patient-sculpted model between 3 and 7%. Under the table tube configurations produced errors less than 5% in most situations due to the flattening affects of the table and pad, and the fact that table height is the main determination of source-to-skin distance for these configurations. In addition to these results, several skin dose maps were produced and a prototype display system was placed on the in-clinic monitor of an interventional fluoroscopy system. The skin dose mapping program developed in this work represents a new tool that, as the RDSR becomes available through automated export or real-time streaming, can provide the interventional physician information needed to modify behavior when clinically appropriate. The program is nonproprietary and transferable, and also functions independent to the software systems already installed on the control room workstation. The next step will be clinical implementation where the workflow will be optimized along with further analysis of real-time capabilities.

LANDSAT-2 and LANDSAT-3 flight evaluation report, 23 April to 23 July 1979

NASA Technical Reports Server (NTRS)

1979-01-01

The performance of satellite subsystems and the response of in-orbit payload systems are summarized. Graphs and tables show the values of the various parameters of these systems. A spacecraft orbit reference table is included.

Documentation for the U.S. Geological Survey Public-Supply Database (PSDB): A database of permitted public-supply wells, surface-water intakes, and systems in the United States

USGS Publications Warehouse

Price, Curtis V.; Maupin, Molly A.

2014-01-01

The purpose of this report is to document the PSDB and explain the methods used to populate and update the data from the SDWIS, State datasets, and map and geospatial imagery. This report describes 3 data tables and 11 domain tables, including field contents, data sources, and relations between tables. Although the PSDB database is not available to the general public, this information should be useful for others who are developing other database systems to store and analyze public-supply system and facility data.

Conceptual Design of the Adaptive Optics System for the Laser Communication Relay Demonstration Ground Station at Table Mountain

NASA Technical Reports Server (NTRS)

Roberts, Lewis C., Jr.; Page, Norman A.; Burruss, Rick S.; Truong, Tuan N.; Dew, Sharon; Troy, Mitchell

2013-01-01

The Laser Communication Relay Demonstration will feature a geostationary satellite communicating via optical links to multiple ground stations. The first ground station (GS-1) is the 1m OCTL telescope at Table Mountain in California. The optical link will utilize pulse position modulation (PPM) and differential phase shift keying (DPSK) protocols. The DPSK link necessitates that adaptive optics (AO) be used to relay the incoming beam into the single mode fiber that is the input of the modem. The GS-1 AO system will have two MEMS Deformable mirrors to achieve the needed actuator density and stroke limit. The AO system will sense the aberrations with a Shack-Hartmann wavefront sensor using the light from the communication link's 1.55 microns laser to close the loop. The system will operate day and night. The system's software will be based on heritage software from the Palm 3000 AO system, reducing risk and cost. The AO system is being designed to work at r(sub 0) greater than 3.3 cm (measured at 500 nm and zenith) and at elevations greater than 20deg above the horizon. In our worst case operating conditions we expect to achieve Strehl ratios of over 70% (at 1.55 microns), which should couple 57% of the light into the single mode DPSK fiber. This paper describes the conceptual design of the AO system, predicted performance and discusses some of the trades that were conducted during the design process.

[A decade of reflection on health plans in Spain. SESPAS report 2010].

PubMed

Fiuza Pérez, María Dolores; Aguiar Rodríguez, Juan Francisco; Monzón Batista, Nayra

2010-12-01

This article reports the experience of the Working Group of the SESPAS-SCSP (Spanish Society of Public Health and Healthcare Administration-Canary Islands Society of Public Health) in health policy and planning during the first decade of the 21st century and its possible impact on the design of health planning. We review the conclusions reached from 2000 to 2008 in the first five Biannual Planning and Health Policy meetings that took place during that period. The workshops were designed with two speakers who presented different views of the subject under discussion, a moderator, who led the debate on the findings, and a narrator who served as a notary and also took responsibility for the text summary of each table. Two general narrators were responsible for the final wording of the conclusions of each workshop or biannual meeting. From 2000 to 2008, there were 25 round tables with 121 conclusions and 160 participants. We believe that the SESPAS working groups provide multidisciplinary professional values within a context of debate in a professional environment, and create spaces for reflection, thus helping to improve the health planning system in Spain. Copyright © 2010 SESPAS. Published by Elsevier Espana. All rights reserved.

Positioning accuracy in a registration-free CT-based navigation system

NASA Astrophysics Data System (ADS)

Brandenberger, D.; Birkfellner, W.; Baumann, B.; Messmer, P.; Huegli, R. W.; Regazzoni, P.; Jacob, A. L.

2007-12-01

In order to maintain overall navigation accuracy established by a calibration procedure in our CT-based registration-free navigation system, the CT scanner has to repeatedly generate identical volume images of a target at the same coordinates. We tested the positioning accuracy of the prototype of an advanced workplace for image-guided surgery (AWIGS) which features an operating table capable of direct patient transfer into a CT scanner. Volume images (N = 154) of a specialized phantom were analysed for translational shifting after various table translations. Variables included added weight and phantom position on the table. The navigation system's calibration accuracy was determined (bias 2.1 mm, precision ± 0.7 mm, N = 12). In repeated use, a bias of 3.0 mm and a precision of ± 0.9 mm (N = 10) were maintainable. Instances of translational image shifting were related to the table-to-CT scanner docking mechanism. A distance scaling error when altering the table's height was detected. Initial prototype problems visible in our study causing systematic errors were resolved by repeated system calibrations between interventions. We conclude that the accuracy achieved is sufficient for a wide range of clinical applications in surgery and interventional radiology.

Using Sensor-based Demand Controlled Ventilation to Realize Energy Savings in Laboratories

DTIC Science & Technology

2014-03-27

is warranted. The results show that a DCV system is life-cycle cost effective for many different HVAC system total pressure and square footage ...Name and Description of System Sensors ......................................................... 44 Table 5. BEL Laboratory HVAC Zones, Square Footage ...Intensity ............................................................................. 74 Table 9. Range of USAF Laboratory Square Footage and Occupancy

40 CFR Table 7 to Subpart Jjj of... - Requirements for Continuous Emission Monitoring Systems (CEMS) a

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false Requirements for Continuous Emission Monitoring Systems (CEMS) a 7 Table 7 to Subpart JJJ of Part 62 Protection of Environment ENVIRONMENTAL...—Requirements for Continuous Emission Monitoring Systems (CEMS) a ER31JA03.013 ...

40 CFR Table 7 to Subpart Jjj of... - Requirements for Continuous Emission Monitoring Systems (CEMS) a

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Requirements for Continuous Emission Monitoring Systems (CEMS) a 7 Table 7 to Subpart JJJ of Part 62 Protection of Environment ENVIRONMENTAL...—Requirements for Continuous Emission Monitoring Systems (CEMS) a ER31JA03.013 ...

Vibration analysis in reciprocating compressors

NASA Astrophysics Data System (ADS)

Kacani, V.

2017-08-01

This paper presents the influence of modelling on the mechanical natural frequencies, the effect of inertia loads on the structure vibration, the impact of the crank gear damping on speed fluctuation to ensure a safe operation and increasing the reliability of reciprocating compressors. In this paper it is shown, that conventional way of modelling is not sufficient. For best results it is required to include the whole system (bare block, frame, coupling, main driver, vessels, pipe work, etc.) in the model (see results in Table 1).

Computer Operations Study of Reservoir Operations for Six Mississippi River Headwaters Dams. Appendix A.

DTIC Science & Technology

1982-06-01

p*A C.._ _ __ _ _ A, d.tibutiou is unhimta 4 iit 84~ L0 TABLE OF CONTENTS APPENDIX SCOPE OF WORK B MERGE AND COST PROGRAM DOCUMENTATION C FATSCO... PROGRAM TO COMPUTE TIME SERIES FREQUENCY RELATIONSHIPS D HEC-DSS - TIME SERIES DATA FILE MANAGEMENT SYSTEM E PLAN 1 -TIM SERIES DATA PLOTS AND ANNUAL...University of Minnesota, utilized an early version of the Hydrologic Engineering * Center’s (HEC) EEC-5c Computer Program . EEC is a Corps of Engineers

Modeling and Optimizing Green Microgrids at Remote U.S. Navy Islands

DTIC Science & Technology

2017-12-01

storage, and controls. All of these components work together as a system solution to serve a nearby load, such as a wind turbine and a storage battery...includes five diesel generators of varying capacities and seven 100kW wind turbines . The diesel genset specifics are shown in Table 1. They typically...run at only 30% of nominal capacity, while they are most efficient at 70% (Anderson et al. 2017). The wind turbines are all Northwind 100 kW models

Utilizing Dynamically Coupled Cores to Form a Resilient Chip Multiprocessor

DTIC Science & Technology

2007-06-01

requires a significant deviation from previous work. For instance, we find that using the relaxed input replication model from Reunion incurs a...Circuit Width Delay Count CRC-16 16 6.65 754 CRC- SDLC -16 16 6.10 888 CRC-32 16 7.28 2260 CRC-32 32 8.60 4240 Table 1. FO4 delay and transistor count for...the operation of our proposed system is the same in all other respects. 4.4 Compatibility Across Memory Consis- tency Models The memory consistency

Habitat Demonstration Unit Medical Operations Workstation Upgrades

NASA Technical Reports Server (NTRS)

Trageser, Katherine H.

2011-01-01

This paper provides an overview of the design and fabrication associated with upgrades for the Medical Operations Workstation in the Habitat Demonstration Unit. The work spanned a ten week period. The upgrades will be used during the 2011 Desert Research and Technology Studies (Desert RATS) field campaign. Upgrades include a deployable privacy curtain system, a deployable tray table, an easily accessible biological waste container, reorganization and labeling of the medical supplies, and installation of a retractable camera. All of the items were completed within the ten week period.

Development of a pilot-scale kinetic extruder feeder system and test program. Phase II. Verification testing. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-01-12

This report describes the work done under Phase II, the verification testing of the Kinetic Extruder. The main objective of the test program was to determine failure modes and wear rates. Only minor auxiliary equipment malfunctions were encountered. Wear rates indicate useful life expectancy of from 1 to 5 years for wear-exposed components. Recommendations are made for adapting the equipment for pilot plant and commercial applications. 3 references, 20 figures, 12 tables.

Handbook of corrosion resistant piping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schweitzer, P.A.

1985-01-01

The book deals with pertinent design, installation, corrosion resistance, and economic factors necessary to determine the optimum system to handle specific corrodents. Each of the materials, both metallic and nonmetallic, is discussed individually. Suitable construction materials are indicated for over 500 corrodents. Available sizes, weights, and types of fittings are given for each material. Tables of permissible working pressures based on the Petroleum Refinery Piping Code, USAS B31.3, have been calculated for each alloy. Service ratings are included for everything discussed.

Collisional Broadening and Shift of D1 and D2 Spectral Lines in Atomic Alkali Vapor - Noble Gas Systems

DTIC Science & Technology

2013-03-01

12 curve fit to the 2Σ1 2� − 2Σ1 2� difference potential Table 2.2a: Lennard - Jones parameters for Rubidium + Helium lines. Difference...Table Page Table 2.2a. Lennard - Jones parameters for Rubidium + Helium lines 22 Table 2.2b. Line broadening and shift parameters for Rb + He lines...all nine M + Ng pairs, using Lennard - Jones (6-12) potentials in Anderson- Talman 25 Table 2.2e. Broadening and shift coefficients (in MHz/torr

Applying fluvial geomorphology to river channel management: Background for progress towards a palaeohydrology protocol

NASA Astrophysics Data System (ADS)

Gregory, K. J.; Benito, G.; Downs, P. W.

2008-06-01

Significant developments have been achieved in applicable and applied fluvial geomorphology as shown in publications of the last three decades, analyzed as the basis for using results of studies of environmental change as a basis for management. The range of types of publications and of activities are more pertinent to river channel management as a result of concern with sustainability, global climate change, environmental ethics, ecosystem health concepts and public participation. Possible applications, with particular reference to river channel changes, include those concerned with form and process, assessment of channel change, urbanization, channelization, extractive industries, impact of engineering works, historical changes in land use, and restoration with specific examples illustrated in Table 1. In order to achieve general significance for fluvial geomorphology, more theory and extension by modelling methods is needed, and examples related to morphology and process characteristics, integrated approaches, and changes of the fluvial system are collected in Table 2. The ways in which potential applications are communicated to decision-makers range from applicable outputs including publications ranging from review papers, book chapters, and books, to applied outputs which include interdisciplinary problem solving, educational outreach, and direct involvement, with examples summarized in Table 3. On the basis of results gained from investigations covering periods longer than continuous records, a protocol embracing palaeohydrological inputs for application to river channel management is illustrated and developed as a synopsis version (Table 4), demonstrating how conclusions from geomorphological research can be expressed in a format which can be considered by managers.

The IRMIS object model and services API.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saunders, C.; Dohan, D. A.; Arnold, N. D.

2005-01-01

The relational model developed for the Integrated Relational Model of Installed Systems (IRMIS) toolkit has been successfully used to capture the Advanced Photon Source (APS) control system software (EPICS process variables and their definitions). The relational tables are populated by a crawler script that parses each Input/Output Controller (IOC) start-up file when an IOC reboot is detected. User interaction is provided by a Java Swing application that acts as a desktop for viewing the process variable information. Mapping between the display objects and the relational tables was carried out with the Hibernate Object Relational Modeling (ORM) framework. Work is wellmore » underway at the APS to extend the relational modeling to include control system hardware. For this work, due in part to the complex user interaction required, the primary application development environment has shifted from the relational database view to the object oriented (Java) perspective. With this approach, the business logic is executed in Java rather than in SQL stored procedures. This paper describes the object model used to represent control system software, hardware, and interconnects in IRMIS. We also describe the services API used to encapsulate the required behaviors for creating and maintaining the complex data. In addition to the core schema and object model, many important concepts in IRMIS are captured by the services API. IRMIS is an ambitious collaborative effort for defining and developing a relational database and associated applications to comprehensively document the large and complex EPICS-based control systems of today's accelerators. The documentation effort includes process variables, control system hardware, and interconnections. The approach could also be used to document all components of the accelerator, including mechanical, vacuum, power supplies, etc. One key aspect of IRMIS is that it is a documentation framework, not a design and development tool. We do not generate EPICS control system configurations from IRMIS, and hence do not impose any additional requirements on EPICS developers.« less

Mechanism of supporting sub-communicator collectives with O(64) counters as opposed to one counter for each sub-communicator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Sameer; Mamidala, Amith R.; Ratterman, Joseph D.

A system and method for enhancing barrier collective synchronization on a computer system comprises a computer system including a data storage device. The computer system includes a program stored in the data storage device and steps of the program being executed by a processor. The system includes providing a plurality of communicators for storing state information for a bather algorithm. Each communicator designates a master core in a multi-processor environment of the computer system. The system allocates or designates one counter for each of a plurality of threads. The system configures a table with a number of entries equal tomore » the maximum number of threads. The system sets a table entry with an ID associated with a communicator when a process thread initiates a collective. The system determines an allocated or designated counter by searching entries in the table.« less

Mechanism of supporting sub-communicator collectives with o(64) counters as opposed to one counter for each sub-communicator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blocksome, Michael; Kumar, Sameer; Mamidala, Amith R.

A system and method for enhancing barrier collective synchronization on a computer system comprises a computer system including a data storage device. The computer system includes a program stored in the data storage device and steps of the program being executed by a processor. The system includes providing a plurality of communicators for storing state information for a barrier algorithm. Each communicator designates a master core in a multi-processor environment of the computer system. The system allocates or designates one counter for each of a plurality of threads. The system configures a table with a number of entries equal tomore » the maximum number of threads. The system sets a table entry with an ID associated with a communicator when a process thread initiates a collective. The system determines an allocated or designated counter by searching entries in the table.« less

Mechanism of supporting sub-communicator collectives with O(64) counters as opposed to one counter for each sub-communicator

DOEpatents

Kumar, Sameer; Mamidala, Amith R.; Ratterman, Joseph D.; Blocksome, Michael; Miller, Douglas

2013-09-03

A system and method for enhancing barrier collective synchronization on a computer system comprises a computer system including a data storage device. The computer system includes a program stored in the data storage device and steps of the program being executed by a processor. The system includes providing a plurality of communicators for storing state information for a bather algorithm. Each communicator designates a master core in a multi-processor environment of the computer system. The system allocates or designates one counter for each of a plurality of threads. The system configures a table with a number of entries equal to the maximum number of threads. The system sets a table entry with an ID associated with a communicator when a process thread initiates a collective. The system determines an allocated or designated counter by searching entries in the table.

Field data and numerical simulation of btex concentration trends under water table fluctuations: Example of a jet fuel-contaminated site in Brazil

NASA Astrophysics Data System (ADS)

Teramoto, Elias Hideo; Chang, Hung Kiang

2017-03-01

Mass transfer of light non-aqueous phase liquids (LNAPLs) trapped in porous media is a complex phenomenon. Water table fluctuations have been identified as responsible for generating significant variations in the concentration of dissolved hydrocarbons. Based on field evidence, this work presents a conceptual model and a numerical solution for mass transfer from entrapped LNAPL to groundwater controlled by both LNAPL saturation and seasonal water table fluctuations within the LNAPL smear zone. The numerical approach is capable of reproducing aqueous BTEX concentration trends under three different scenarios - water table fluctuating within smear zone, above the smear zone and partially within smear zone, resulting in in-phase, out-of-phase and alternating in-phase and out-of-phase BTEX concentration trend with respect to water table oscillation, respectively. The results demonstrate the model's applicability under observed field conditions and its ability to predict source zone depletion.

EPOS IP - Data, Data Products, Services and Software (DDSS Master Table)

NASA Astrophysics Data System (ADS)

Michalek, Jan; Atakan, Kuvvet

2017-04-01

The "European Plate Observing System - Implementation Phase" (EPOS IP, 2014-2019) project is about building a pan-European infrastructure for accessing solid Earth science data. This ambitious plan started in 2002 already with a Conception Phase and continued by an EPOS PP (Preparatory Phase, 2010-2014) where about 20 partners joined the project. The current EPOS IP project includes 47 partners plus 6 associate partners from 25 countries from all over Europe and several international organizations (ORFEUS, EMSC, EUREF). However, the community contributing to the EPOS integration plan is larger than the official partnership of EPOS IP project, because more countries are represented by the international organizations and because within each country there are several research institutions involved. The list of Data, Data Products, Services and Software (DDSS) provided by individual institutions, consortia or organizations which will become part of the EPOS system are currently collected in document called DDSS Master Table. There are 10 work packages (WP8-WP17) creating the Thematic Core Services (TCS) always grouped by a specific topic: Seismology, Near Fault Observatories, GNSS Data and Products, Volcano Observations, Satellite Data, Geomagnetic Observations, Anthropogenic Hazards, Geological Information and Modelling, Multi-scale laboratories and Geo-Energy Test Beds for Low Carbon Energy. Each of this group declared a list of DDSS elements which are about to be implemented. Currently there are about 455 DDSS elements in the DDSS Master Table. These DDSS elements are of different maturity and about 122 are declared by TCS groups to be ready for implementation which means that the data are well described with metadata, following the standards specific for their domain and, in the best case, with some services allowing their access already. The DDSS elements differ by its complexity as well. The DDSS Master Table serves as an overview of the DDSS elements and includes most of the important information needed for further implementation and is continuously updated as the project evolves. The presentation is showing statistics describing the current status of DDSS Master Table and complexity of the organizational structure at the TCS level.

Ecological periodic tables for nekton and benthic macrofaunal community usage of estuarine habitats

EPA Science Inventory

Background/Questions/Methods The chemical periodic table, the Linnaean system of classification, and the Hertzsprung-Russell diagram are iconic information organizing systems because they are simple, easy to understand, exceptionally useful, and they foster the expansion of sc...

42 CFR 100.3 - Vaccine injury table.

Code of Federal Regulations, 2011 CFR

2011-10-01

... to rheumatoid arthritis, juvenile rheumatoid arthritis, systemic lupus erythematosus, systemic... Not applicable. IV. Vaccines containing rubella virus (e.g., MMR, MR, R) A. Chronic arthritis 7-42... listed in the Vaccine Injury Table. (6) Chronic Arthritis. (i) For purposes of paragraph (a) of this...

42 CFR 100.3 - Vaccine injury table.

Code of Federal Regulations, 2014 CFR

2014-10-01

... to rheumatoid arthritis, juvenile rheumatoid arthritis, systemic lupus erythematosus, systemic... Not applicable. IV. Vaccines containing rubella virus (e.g., MMR, MR, R) A. Chronic arthritis 7-42... listed in the Vaccine Injury Table. (6) Chronic Arthritis. (i) For purposes of paragraph (a) of this...

42 CFR 100.3 - Vaccine injury table.

Code of Federal Regulations, 2010 CFR

2010-10-01

... to rheumatoid arthritis, juvenile rheumatoid arthritis, systemic lupus erythematosus, systemic.... IV. Vaccines containing rubella virus (e.g., MMR, MR, R) A. Chronic arthritisB. Any acute... listed in the Vaccine Injury Table. (6) Chronic Arthritis. (i) For purposes of paragraph (a) of this...

42 CFR 100.3 - Vaccine injury table.

Code of Federal Regulations, 2013 CFR

2013-10-01

... to rheumatoid arthritis, juvenile rheumatoid arthritis, systemic lupus erythematosus, systemic... Not applicable. IV. Vaccines containing rubella virus (e.g., MMR, MR, R) A. Chronic arthritis 7-42... listed in the Vaccine Injury Table. (6) Chronic Arthritis. (i) For purposes of paragraph (a) of this...

42 CFR 100.3 - Vaccine injury table.

Code of Federal Regulations, 2012 CFR

2012-10-01

... to rheumatoid arthritis, juvenile rheumatoid arthritis, systemic lupus erythematosus, systemic... Not applicable. IV. Vaccines containing rubella virus (e.g., MMR, MR, R) A. Chronic arthritis 7-42... listed in the Vaccine Injury Table. (6) Chronic Arthritis. (i) For purposes of paragraph (a) of this...

Determining the Marker Configuration and Modeling Technique to Optimize the Biomechanical Analysis of Running-Specific Prostheses

DTIC Science & Technology

2011-08-01

4 Body ...Report requirement. 5 Body The approved Statement of Work proposed the following timeline (Table 1): Table 1. Timeline for approved project...Figure 1) were tested for this project including the 1E90 Sprinter (OttoBock Inc.), Flex-Run (Ossur), Cheetah ® (Ossur) and Nitro Running Foot (Freedom

Determining the Marker Configuration and Modeling Technique to Optimize the Biomechanical Analysis of Running-Specific Prostheses

DTIC Science & Technology

2012-03-01

4 Body ...Final Report requirement. 5  Body The approved Statement of Work proposed the following timeline (Table 1): Table 1. Timeline for...prosthesis designs (Figure 1) were tested for this project including the 1E90 Sprinter (OttoBock Inc.), Flex-Run (Ossur), Cheetah ® (Ossur) and Nitro

Occupational Education for Students with Special Needs: Master Table of Contents for 17-Volume Series.

ERIC Educational Resources Information Center

Nassau County Board of Cooperative Educational Services, Westbury, NY.

This master table of contents provides a comprehensive overview of all seventeen books included in a series of curriculum resource guides for occupational teachers who work with special needs students. Each includes performance objectives and suggested instructional activities for job behaviors and attitudes common to all employment as well as to…

VIEW OF SHEAR (ELECTRIC POWERED), SCALE HOUSE TO LEFT. BARS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF SHEAR (ELECTRIC POWERED), SCALE HOUSE TO LEFT. BARS ARE PLACED ON WEIGHING SCALE SHOWN LOWER LEFT. 15-TON CLEVELAND CRANE HANDLES BARS FOR FINAL LOADING INTO RAILROAD CARS (12" BAY) AND FOR MOVING FROM TABLE TO SHEAR TABLE. - Cambria Iron Company, Gautier Works, 12" Mill, Clinton Street & Little Conemaugh River, Johnstown, Cambria County, PA

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2012 CFR

2012-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2011 CFR

2011-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2013 CFR

2013-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2014 CFR

2014-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

A prospective, single-arm study on the use of the da Vinci® Table Motion with the Trumpf TS7000dV operating table.

PubMed

Morelli, Luca; Palmeri, Matteo; Simoncini, Tommaso; Cela, Vito; Perutelli, Alessandra; Selli, Cesare; Buccianti, Piero; Francesca, Francesco; Cecchi, Massimo; Zirafa, Cristina; Bastiani, Luca; Cuschieri, Alfred; Melfi, Franca

2018-03-30

The da Vinci® Table Motion (dVTM) comprises a combination of a unique operating table (Trumpf Medical™ TruSystem® 7000dV) capable of isocenter motion connected wirelessly with the da Vinci Xi® robotic platform, thereby enabling patients to be repositioned without removal of instruments and or undocking the robot. Between May 2015 to October 2015, the first human use of dVTM was carried out in this prospective, single-arm, post-market study in the EU, for which 40 patients from general surgery (GS), urology (U), or gynecology (G) were enrolled prospectively. Primary endpoints of the study were dVTM feasibility, efficacy, and safety. Surgeons from the three specialties obtained targeting success and the required table positioning in all cases. Table movement/repositioning was necessary to gain exposure of the operating field in 106/116 table moves (91.3%), change target in 2/116 table moves (1.7%), achieve hemodynamic relief in 4/116 table moves (3.5%), and improve external access for tumor removal in 4/116 table moves (3.5%). There was a significantly higher use of tilt and tilt plus Trendelenburg in GS group (GS vs. U p = 0.055 and GS vs. G p = 0.054). There were no dVTM safety-related or adverse events. The dVTM with TruSystem 7000dV operating table in wireless communication with the da Vinci Xi is a perfectly safe and effective synergistic combination, which allows repositioning of the patient whenever needed without imposing any delay in the execution of the operation. Moreover, it is helpful in avoiding extreme positions and enables the anesthesiologist to provide immediate and effective hemodynamic relief to the patient when needed.

Carl Linnaeus and the visual representation of nature.

PubMed

Charmantier, Isabelle

2011-01-01

The Swedish naturalist Carl Linnaeus (1707-1778) is reputed to have transformed botanical practice by shunning the process of illustrating plants and relying on the primacy of literary descriptions of plant specimens. Botanists and historians have long debated Linnaeus's capacities as a draftsman. While some of his detailed sketches of plants and insects reveal a sure hand, his more general drawings of landscapes and people seem ill-executed. The overwhelming consensus, based mostly on his Lapland diary (1732), is that Linnaeus could not draw. Little has been said, however, on the role of drawing and other visual representations in Linnaeus's daily work as seen in his other numerous manuscripts. These manuscripts, held mostly at the Linnean Society of London, are peppered with sketches, maps, tables, and diagrams. Reassessing these manuscripts, along with the printed works that also contain illustrations of plant species, shows that Linnaeus's thinking was profoundly visual and that he routinely used visual representational devices in his various publications. This paper aims to explore the full range of visual representations Linnaeus used through his working life, and to reevaluate the epistemological value of visualization in the making of natural knowledge. By analyzing Linnaeus's use of drawings, maps, tables, and diagrams, I will show that he did not, as has been asserted, reduce the discipline of botany to text, and that his visual thinking played a fundamental role in his construction of new systems of classification.

Integrated Robust Open-Set Speaker Identification System (IROSIS)

DTIC Science & Technology

2012-05-01

29 LIST OF TABLES Table 1. Detail of NIST Data Used for Training and Testing ............................................ 3 Table 2...scenarios are referred to as VB-YB, VL-YL, VB-YL and VL-YB respectively. Table 1. Detail of NIST Data Used for Training and Testing Purpose Source No...M is the UBM supervector, and that the difference between ( )L m and ( , )Q M m is the Kullback - Leibler divergence between the “alignment” of the

Hydrologic conditions, recharge, and baseline water quality of the surficial aquifer system at Jekyll Island, Georgia, 2012-13

USGS Publications Warehouse

Gordon, Debbie W.; Torak, Lynn J.

2016-03-08

Groundwater levels and specific-conductance measurements showed the dependence of freshwater resources on rainfall to recharge the water-table zone of the surficial aquifer system and to influence groundwater flow on Jekyll Island. The unseasonably dry conditions during November 2012 to April 2013 induced saline water infiltration to the water-table zone from the marshland separating the Jekyll River from the island. A strong correlation (R2 = 0.97) of specific conductance to chloride concentration in water samples from wells installed in the water-table zone provided support for the determination of seasonal directions of groundwater flow by confirming salinity changes in the water-table zone. Unseasonably wet conditions during the late spring to August caused groundwater-flow reversals in some areas. The high dependence of the water-table zone in the surficial aquifer system on precipitation to replenish the aquifer with freshwater underscored the importance of monitoring groundwater levels, water quality, and water use to identify aquifer-discharge conditions that have the potential to promote seawater encroachment and degrade freshwater resources on Jekyll Island.

A Comparative Study on Safe Pile Capacity as Shown in Table 1 of IS 2911 (Part III): 1980

NASA Astrophysics Data System (ADS)

Pakrashi, Somdev

2017-06-01

Code of practice for design and construction of under reamed pile foundations: IS 2911 (Part-III)—1980 presents one table in respect of safe load for bored cast in situ under reamed piles in sandy and clayey soils including black cotton soils, stem dia. of pile ranging from 20 to 50 cm and its effective length being 3.50 m. A comparative study, was taken up by working out safe pile capacity for one 400 dia., 3.5 m long bored cast in situ under reamed pile based on subsoil properties obtained from soil investigation work as well as subsoil properties of different magnitudes of clayey, sandy soils and comparing the same with the safe pile capacity shown in Table 1 of that IS Code. The study reveals that safe pile capacity computed from subsoil properties, barring a very few cases, considerably differs from that shown in the aforesaid code and looks forward for more research work and study to find out a conclusive explanation of this probable anomaly.

Development and application of remote video monitoring system for combine harvester based on embedded Linux

NASA Astrophysics Data System (ADS)

Chen, Jin; Wang, Yifan; Wang, Xuelei; Wang, Yuehong; Hu, Rui

2017-01-01

Combine harvester usually works in sparsely populated areas with harsh environment. In order to achieve the remote real-time video monitoring of the working state of combine harvester. A remote video monitoring system based on ARM11 and embedded Linux is developed. The system uses USB camera for capturing working state video data of the main parts of combine harvester, including the granary, threshing drum, cab and cut table. Using JPEG image compression standard to compress video data then transferring monitoring screen to remote monitoring center over the network for long-range monitoring and management. At the beginning of this paper it describes the necessity of the design of the system. Then it introduces realization methods of hardware and software briefly. And then it describes detailedly the configuration and compilation of embedded Linux operating system and the compiling and transplanting of video server program are elaborated. At the end of the paper, we carried out equipment installation and commissioning on combine harvester and then tested the system and showed the test results. In the experiment testing, the remote video monitoring system for combine harvester can achieve 30fps with the resolution of 800x600, and the response delay in the public network is about 40ms.

Northern part, Ten Mile and Taunton River basins

USGS Publications Warehouse

Williams, John R.; Willey, Richard E.

1967-01-01

This report is one of two prepared by the Geological Survey for the Water Resources Commission. The principal purpose of this report is to make available the basic data on which the other, a map showing availability of ground water, is based. This basic-data report also can be used by engineers, planners, and others interested in or responsible for water-resources planning to determine the materials to be encountered (tables 3 and 4) and the yields which may be obtained from wells and test holes (tables 1 and 2) in the stratified sand and gravel that are the principal source of ground water and in bedrock. Partial and complete chemical analyses (tables 7 and 8) of these test holes and of some privately-owned wells provide information on the general quality of the water for domestic and other uses. A tabulation of existing municipal supplies, their capacity, production (table 5), and chemical quality of the water (table 6) may be used for regional planning purposes. Water-level measurements (figure 1) can be used to determine the annual fluctuations of the water table in certain types of materials. Seismic work (table 9) in the Canoe River valley, Norton, and test drilling with a power augur (tables 2 and 4) were done for the Geological Survey as  part of the investigation.

Fatal and Injury Accident Rates on Federal-Aid and Other Highway Systems/1975

DOT National Transportation Integrated Search

1977-01-28

Data on fatal and nonfatal injuries in motor vehicle traffic accidents for calendar year 1975 are summarized by highway system in the tables. These tables, compiled from reports submitted to the Federal Highway Administration by the 50 States and the...

Fatal and Injury Accident Rates on Federal-Aid and Other Highway Systems/1974

DOT National Transportation Integrated Search

1975-11-01

Data on fatal and nonfatal injuries in motor vehicle traffic accidents for calendar year 1974 are summarized by highway system in the tables. These tables, compiled from reports submitted to the Federal Highway Administration by the 50 States and the...

IMS/Satellite Situation Center report. Predicted orbit plots for IMP-H-1976. [Explorer 47 satellite

NASA Technical Reports Server (NTRS)

1975-01-01

Predicted orbit plots are shown in three projections. The time period covered by each set of projections is 12 days 6 hours, corresponding approximately to the period of IMP-H satellite. The three coordinate systems used are the Geocentric Solar Ecliptic system (GSE), the Geocentric Solar Magnetospheric system (GSM), and the Solar Magnetic system (SM). For each of the three projections, time ticks and codes are given on the satellite trajectories. The codes are interpreted in the table at the base of each plot. Time is given in the table as year/day/decimal hour. The total time covered by each plot is shown at the bottom of each table. An additional variable is given in the table for each time tick. For the GSM and SM projection this variable is the geocentric distance to the satellite in earth radii, and for the GSE projection the variable is satellite ecliptic latitude in degrees.

Estimating occupational illness, injury, and mortality in food production in the United States: A farm-to-table analysis

PubMed Central

Leon, Juan S.; Newman, Lee S.

2015-01-01

Objectives The study provides a novel model and more comprehensive estimates of the burden of occupational morbidity and mortality in food-related industries, using a farm-to-table approach. Methods The authors analyzed 2008–2010 US Bureau of Labor Statistics data for private industries in the different stages of the farm-to-table model (production; processing; distribution and storage; retail and preparation). Results The morbidity rate for food system industries were significantly higher than the morbidity rate for non-food system industries (Rate Ratio (RR)=1.62, 95% Confidence Interval (CI): 1.30–2.01). Furthermore, the occupational mortality rate for food system industries was significantly higher than the national non-food occupational mortality rate (RR=9.51, 95% CI: 2.47–36.58). Conclusions This is the first use of the farm-to-table model to assess occupational morbidity and mortality, and these findings highlighting specific workplace hazards across food system industries. PMID:25970031

Women: work and health.

PubMed

Wagener, D K; Walstedt, J; Jenkins, L; Burnett, C; Lalich, N; Fingerhut, M

1997-12-01

This report describes the sociodemographics, household characteristics, and health of women according to workforce status and job conditions. The report also presents data on men for comparison. This report combines data from numerous data systems, including: The National Health Interview Survey, National Health and Nutrition Examination Survey, National Maternal and Infant Health Survey, National Hospital Ambulatory Medical Care Survey, National Traumatic Occupational Fatalities Surveillance System, and the National Occupational Mortality Surveillance System, which are conducted by the U.S. Department of Health and Human Services; the Census of Fatal Occupational Injuries and Annual Survey of Occupational injuries and illnesses conducted by the U.S. Department of Labor; and the Current Population Survey conducted by the U.S. Department of Commerce. The report also presents selected tables from publications of the Women's Bureau and the Bureau of Labor Statistics, U.S. Department of Labor. The report presents summary data on physical conditions and exposures, health conditions attributed to work, other health conditions that impact on work, health promotion in the workplace, and health-related benefits provided by employers. Most estimates are shown according to sex, age, race, ethnicity, educational attainment, and major occupational group.

40 CFR Table 6 to Subpart Jjj of... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 8 2011-07-01 2011-07-01 false Requirements for Validating Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart JJJ of Part 62 Protection of Environment... of Part 62—Requirements for Validating Continuous Emission Monitoring Systems (CEMS) ER31JA03.012 ...

40 CFR Table 4 to Subpart Ffff of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS) 4 Table 4 to Subpart FFFF of Part 60 Protection of Environment...—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.3039, you...

40 CFR Table 4 to Subpart Ffff of... - Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Model Rule-Requirements for Continuous Emission Monitoring Systems (CEMS) 4 Table 4 to Subpart FFFF of Part 60 Protection of Environment...—Model Rule—Requirements for Continuous Emission Monitoring Systems (CEMS) As stated in § 60.3039, you...

40 CFR Table 6 to Subpart Jjj of... - Requirements for Validating Continuous Emission Monitoring Systems (CEMS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Requirements for Validating Continuous Emission Monitoring Systems (CEMS) 6 Table 6 to Subpart JJJ of Part 62 Protection of Environment... of Part 62—Requirements for Validating Continuous Emission Monitoring Systems (CEMS) ER31JA03.012 ...

A Reconceptualization of the Adaptability Rating for Military Aviation

DTIC Science & Technology

2017-01-01

7 LIST OF TABLES Page Table 1. Flying Adaptability Rating System in 1931...colleagues, and one that satisfies the needs of the system by fostering cooperation with Line leadership. 2 DISTRIBUTION STATEMENT A. Approved for...came the Flying Adaptability Rating. Assigning value to certain variables, it used a grading system in an attempt to predict whether the candidate

Integrative rehabilitation of residents chronic post-stroke in skilled nursing facilities: the design and evaluation of the BrightArm Duo.

PubMed

House, G; Burdea, G; Polistico, K; Roll, D; Kim, J; Grampurohit, N; Damiani, F; Keeler, S; Hundal, J; Pollack, S

2016-11-01

To describe the novel BrightArm Duo bimanual upper extremity (UE) rehabilitation system; to determine its technology acceptance and clinical benefit for older hemiplegic participants. The system table tilted to adjust arm gravity loading. Participants wore arm supports that sensed grasp strength and wrist position on the table. Wrist weights further increased shoulder exertion. Games were designed to improve UE strength, motor function, cognition and emotive state and adapted automatically to each participant. The system underwent feasibility trials spanning 8 weeks in two skilled nursing facilities (SNFs). Participants were evaluated pre-therapy and post-therapy using standardized clinical measures. Computerized measures of supported arm reach, table tilt and number of arm repetitions were stored on a remote server. Seven participants had significant improvements in their active range of shoulder movement, supported arm reach, shoulder strength, grasp strength and their ability to focus. The group demonstrated higher arm function measured with FMA (p = 0.01) and CAHAI (p = 0.05), and had an improvement in depression (Becks Depression Inventory, II). BrightArm Duo technology was well accepted by participants with a rating of 4.4 out of 5 points. Given these findings, it will be beneficial to evaluate the BrightArm Duo application in SNF maintenance programs. Implications for Rehabilitation Integrative rehabilitation that addresses both physical and cognitive domains is promising for post-stroke maintenance in skilled nursing facilities. Simultaneous bilateral arm exercise may improve arm function in older hemiplegic patients several years after stroke. Virtual reality games that adapt to the patient can increase attention and working memory while decreasing depression in elderly.

STREAM Table Program: User's manual and program document

NASA Technical Reports Server (NTRS)

Hiles, K. H.

1981-01-01

This program was designed to be an editor for the Lewis Chemical Equilibrium program input files and is used for storage, manipulation and retrieval of the large amount of data required. The files are based on the facility name, case number, and table number. The data is easily recalled by supplying the sheet number to be displayed. The retrieval basis is a sheet defined to be all of the individual flow streams which comprise a given portion of a coal gasification system. A sheet may cover more than one page of output tables. The program allows for the insertion of a new table, revision of existing tables, deletion of existing tables, or the printing of selected tables. No calculations are performed. Only pointers are used to keep track of the data.

Density-Functional-Theory-Based Equation-of-State Table of Beryllium for Inertial Confinement Fusion Applications

NASA Astrophysics Data System (ADS)

Ding, Y. H.; Hu, S. X.

2017-10-01

Beryllium has been considered a superior ablator material for inertial confinement fusion target designs. Based on density-functional-theory calculations, we have established a wide-range beryllium equation-of-state (EOS) table of density ρ = 0.001 to ρ = 500 g/cm3 and temperature T = 2000 to 108 K. Our first-principles equation-of-state (FPEOS) table is in better agreement with widely used SESAMEEOS table (SESAME2023) than the average-atom INFERNOmodel and the Purgatoriomodel. For the principal Hugoniot, our FPEOS prediction shows 10% stiffer behavior than the last two models at maximum compression. Comparisons between FPEOS and SESAMEfor off-Hugoniot conditions show that both the pressure and internal energy differences are within 20% between two EOS tables. By implementing the FPEOS table into the 1-D radiation-hydrodynamics code LILAC, we studied the EOS effects on beryllium target-shell implosions. The FPEOS simulation predicts up to an 15% higher neutron yield compared to the simulation using the SESAME2023 EOS table. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

User testing and stakeholder feedback contributed to the development of understandable and useful Summary of Findings tables for Cochrane reviews.

PubMed

Rosenbaum, Sarah E; Glenton, Claire; Nylund, Hilde Kari; Oxman, Andrew D

2010-06-01

To develop a Summary of Findings (SoF) table for use in Cochrane reviews that is understandable and useful for health professionals, acceptable to Cochrane Collaboration stakeholders, and feasible to implement. We gathered stakeholder feedback on the format and content of an SoF table from an advisory group of more than 50 participants and their constituencies through e-mail consultations. We conducted user tests using a think-aloud protocol method, collecting feedback from 21 health professionals and researchers in Norway and the UK. We analyzed the feedback, defined problem areas, and generated new solutions in brainstorming workshops. Stakeholders were concerned about precision in the data representation and about production feasibility. User testing revealed unexpected comprehension problems, mainly confusion about what the different numbers referred to (class reference). Resolving the tension between achieving table precision and table simplicity became the main focus of the working group. User testing led to a table more useful and understandable for clinical audiences. We arrived at an SoF table that was acceptable to the stakeholders and in principle feasible to implement technically. Some challenges remain, including presenting continuous outcomes and technical/editorial implementation.

VizieR Online Data Catalog: Spectroscopic survey of youngest field stars II. (Frasca+, 2018)

NASA Astrophysics Data System (ADS)

Frasca, A.; Guillout, P.; Klutsch, A.; Freire Ferrero, R.; Marilli, E.; Biazzo, K.; Gandolfi, D.; Montes, D.

2018-01-01

Radial velocity (RV) and projected rotational velocity (vsini) of the single stars and SB1 systems are quoted in Table A1 along with the V magnitude and B-V color index. The vsini values measured from the full width at half maximum of the of the cross-correlation function (CCF) and by means of the code ROTFIT are both listed in Table A1. Table A2 and A3 report RV and vsini from the CCF for the components of SB2 and triple (SB3) systems, respectively. Table A4 reports, for the single stars and SB1 systems, the spectral type, atmospheric parameters (Teff, logg, and [Fe/H]), the equivalent width of the lithium 6708-A line (corrected for the FeI blends) and the net equivalent width of Hα line, measured after the subtraction of the inactive photospheric template. (4 data files).

Space Settlements: A Design Study

NASA Technical Reports Server (NTRS)

Johnson, Richard D. (Editor); Holbrow, Charles (Editor)

1977-01-01

Nineteen professors of engineering, physical science, social science, and architecture, three volunteers, six students, a technical director, and two co-directors worked for ten weeks to construct a convincing picture of how people might permanently sustain life in space on a large scale, and to design a system for the colonization of space. Because the idea of colonizing space has awakened strong public interest, the document presented is written to be understood by the educated public and specialists in other fields. It also includes considerable background material. A table of units and conversion factors is included to aid the reader in interpreting the units of the metric system used in the report.

Open-Loop Pitch Table Optimization for the Maximum Dynamic Pressure Orion Abort Flight Test

NASA Technical Reports Server (NTRS)

Stillwater, Ryan A.

2009-01-01

NASA has scheduled the retirement of the space shuttle orbiter fleet at the end of 2010. The Constellation program was created to develop the next generation of human spaceflight vehicles and launch vehicles, known as Orion and Ares respectively. The Orion vehicle is a return to the capsule configuration that was used in the Mercury, Gemini, and Apollo programs. This configuration allows for the inclusion of an abort system that safely removes the capsule from the booster in the event of a failure on launch. The Flight Test Office at NASA's Dryden Flight Research Center has been tasked with the flight testing of the abort system to ensure proper functionality and safety. The abort system will be tested in various scenarios to approximate the conditions encountered during an actual Orion launch. Every abort will have a closed-loop controller with an open-loop backup that will direct the vehicle during the abort. In order to provide the best fit for the desired total angle of attack profile with the open-loop pitch table, the table is tuned using simulated abort trajectories. A pitch table optimization program was created to tune the trajectories in an automated fashion. The program development was divided into three phases. Phase 1 used only the simulated nominal run to tune the open-loop pitch table. Phase 2 used the simulated nominal and three simulated off nominal runs to tune the open-loop pitch table. Phase 3 used the simulated nominal and sixteen simulated off nominal runs to tune the open-loop pitch table. The optimization program allowed for a quicker and more accurate fit to the desired profile as well as allowing for expanded resolution of the pitch table.

L5 TM radiometric recalibration procedure using the internal calibration trends from the NLAPS trending database

USGS Publications Warehouse

Chander, G.; Haque, Md. O.; Micijevic, E.; Barsi, J.A.

2008-01-01

From the Landsat program's inception in 1972 to the present, the earth science user community has benefited from a historical record of remotely sensed data. The multispectral data from the Landsat 5 (L5) Thematic Mapper (TM) sensor provide the backbone for this extensive archive. Historically, the radiometric calibration procedure for this imagery used the instrument's response to the Internal Calibrator (IC) on a scene-by-scene basis to determine the gain and offset for each detector. The IC system degraded with time causing radiometric calibration errors up to 20 percent. In May 2003 the National Landsat Archive Production System (NLAPS) was updated to use a gain model rather than the scene acquisition specific IC gains to calibrate TM data processed in the United States. Further modification of the gain model was performed in 2007. L5 TM data that were processed using IC prior to the calibration update do not benefit from the recent calibration revisions. A procedure has been developed to give users the ability to recalibrate their existing Level-1 products. The best recalibration results are obtained if the work order report that was originally included in the standard data product delivery is available. However, many users may not have the original work order report. In such cases, the IC gain look-up table that was generated using the radiometric gain trends recorded in the NLAPS database can be used for recalibration. This paper discusses the procedure to recalibrate L5 TM data when the work order report originally used in processing is not available. A companion paper discusses the generation of the NLAPS IC gain and bias look-up tables required to perform the recalibration.

Permanent-File-Validation Utility Computer Program

NASA Technical Reports Server (NTRS)

Derry, Stephen D.

1988-01-01

Errors in files detected and corrected during operation. Permanent File Validation (PFVAL) utility computer program provides CDC CYBER NOS sites with mechanism to verify integrity of permanent file base. Locates and identifies permanent file errors in Mass Storage Table (MST) and Track Reservation Table (TRT), in permanent file catalog entries (PFC's) in permit sectors, and in disk sector linkage. All detected errors written to listing file and system and job day files. Program operates by reading system tables , catalog track, permit sectors, and disk linkage bytes to vaidate expected and actual file linkages. Used extensively to identify and locate errors in permanent files and enable online correction, reducing computer-system downtime.

Development and analysis of SCR requirements tables for system scenarios

NASA Technical Reports Server (NTRS)

Callahan, John R.; Morrison, Jeffery L.

1995-01-01

We describe the use of scenarios to develop and refine requirement tables for parts of the Earth Observing System Data and Information System (EOSDIS). The National Aeronautics and Space Administration (NASA) is developing EOSDIS as part of its Mission-To-Planet-Earth (MTPE) project to accept instrument/platform observation requests from end-user scientists, schedule and perform requested observations of the Earth from space, collect and process the observed data, and distribute data to scientists and archives. Current requirements for the system are managed with tools that allow developers to trace the relationships between requirements and other development artifacts, including other requirements. In addition, the user community (e.g., earth and atmospheric scientists), in conjunction with NASA, has generated scenarios describing the actions of EOSDIS subsystems in response to user requests and other system activities. As part of a research effort in verification and validation techniques, this paper describes our efforts to develop requirements tables from these scenarios for the EOSDIS Core System (ECS). The tables specify event-driven mode transitions based on techniques developed by the Naval Research Lab's (NRL) Software Cost Reduction (SCR) project. The SCR approach has proven effective in specifying requirements for large systems in an unambiguous, terse format that enhance identification of incomplete and inconsistent requirements. We describe development of SCR tables from user scenarios and identify the strengths and weaknesses of our approach in contrast to the requirements tracing approach. We also evaluate the capabilities of both approach to respond to the volatility of requirements in large, complex systems.

A New Methodology for Vibration Error Compensation of Optical Encoders

PubMed Central

Lopez, Jesus; Artes, Mariano

2012-01-01

Optical encoders are sensors based on grating interference patterns. Tolerances inherent to the manufacturing process can induce errors in the position accuracy as the measurement signals stand apart from the ideal conditions. In case the encoder is working under vibrations, the oscillating movement of the scanning head is registered by the encoder system as a displacement, introducing an error into the counter to be added up to graduation, system and installation errors. Behavior improvement can be based on different techniques trying to compensate the error from measurement signals processing. In this work a new “ad hoc” methodology is presented to compensate the error of the encoder when is working under the influence of vibration. The methodology is based on fitting techniques to the Lissajous figure of the deteriorated measurement signals and the use of a look up table, giving as a result a compensation procedure in which a higher accuracy of the sensor is obtained. PMID:22666067

Uniform data system standardizes technical computations and the purchasing of commercially important gases

NASA Technical Reports Server (NTRS)

Johnson, V. J.; Mc Carty, R. D.; Roder, H. M.

1970-01-01

Integrated tables of pressure, volume, and temperature for the saturated liquid, from the triple point to the critical point of the gases, have been developed. Tables include definition of saturated liquid curve. Values are presented in metric and practical units. Advantages of the new tables are discussed.

Formulas of Site Index Prediction Tables for Oak in Missouri

Treesearch

Harry V. Jr. Wiant; Robert A. McQuilkin

1976-01-01

Recently published site index prediction tables for oak in Missouri were fomulized using the "matchacurve" system. The average absolute differences between formula and table values were .8 feet for white oak and 1.4 feet for black and scarlet oaks; maximum differences were 3.0 and 4.2 feet, respectively.

Supplemental Tables to the Annual Energy Outlook

EIA Publications

2017-01-01

The Annual Energy Outlook (AEO) Supplemental tables were generated for the reference case of the AEO using the National Energy Modeling System, a computer-based model which produces annual projections of energy markets. Most of the tables were not published in the AEO, but contain regional and other more detailed projections underlying the AEO projections.

A World of Difference: A Global Survey of University League Tables. Canadian Education Report Series

ERIC Educational Resources Information Center

Usher, Alex; Savino, Massimo

2006-01-01

In this document we discuss 19 university league tables and ranking systems from around the world. Sixteen of these are "national" league tables collected from ten countries (Australia, Canada, China, Germany, Hong Kong, Italy, Poland, Spain, the United Kingdom and the United States); three are "international" or…

Improvements in flight table dynamic transparency for hardware-in-the-loop facilities

NASA Astrophysics Data System (ADS)

DeMore, Louis A.; Mackin, Rob; Swamp, Michael; Rusterholtz, Roger

2000-07-01

Flight tables are a 'necessary evil' in the Hardware-In-The- Loop (HWIL) simulation. Adding the actual or prototypic flight hardware to the loop, in order to increase the realism of the simulation, forces us to add motion simulation to the process. Flight table motion bases bring unwanted dynamics, non- linearities, transport delays, etc to an already difficult problem sometimes requiring the simulation engineer to compromise the results. We desire that the flight tables be 'dynamically transparent' to the simulation scenario. This paper presents a State Variable Feedback (SVF) control system architecture with feed-forward techniques that improves the flight table's dynamic transparency by significantly reducing the table's low frequency phase lag. We offer some actual results with existing flight tables that demonstrate the improved transparency. These results come from a demonstration conducted on a flight table in the KHILS laboratory at Eglin AFB and during a refurbishment of a flight table for the Boeing Company of St. Charles, Missouri.

Microchemical Systems for Fuel Processing and Conversion to Electrical Power

DTIC Science & Technology

2007-03-15

Processing and Conversion to Electrical Power - Final Report 2 Table of Contents Table of Contents... Processing and Conversion to Electrical Power - Final Report 3 8.7 Development of Large Free-Standing Electrolyte-supported Micro Fuel Cell Membranes...84 MURI Microchemical Systems for Fuel Processing and

Fatal and Injury Accident Rates on Federal-Aid and Other Highway Systems/1973

DOT National Transportation Integrated Search

1974-11-01

Data on fatal and nonfatal injuries in motor vehicle traffic accidents for calendar year 1973 are summarized highway system in the tables. These tables, compiled from reports submitted by the 50 States and the District of Columbia, include data for a...

Climate change impact on groundwater levels in the Guarani Aquifer outcrop zone

NASA Astrophysics Data System (ADS)

Melo, D. D.; Wendland, E.

2013-12-01

The unsustainable use of groundwater in many countries might cause water availability restrictions in the future. Such issue is likely to worsen due to predicted climate changes for the incoming decades. As numerous studies suggest, aquifers recharge rates will be affected as a result of climate change. The Guarani Aquifer System (GAS) is one of the most important transboundary aquifer in the world, providing drinkable water for millions of people in four South American countries (Brazil, Argentina, Uruguay and Paraguay). Considering the GAS relevance and how its recharge rates might be altered by climatic conditions anomalies, the objective of this work is to assess possible climate changes impacts on groundwater levels in this aquifer outcrop zone. Global Climate Models' (GCM) outputs were used as inputs in a transient flux groundwater model created using the software SPA (Simulation of Process in Aquifers), enabling groundwater table fluctuation to be evaluated under distinct climatic scenarios. Six monitoring wells, located in a representative basin (Ribeirão da Onça basin) inside a GAS outcrop zone (ROB), provided water table measurements between 2004 and 2011 to calibrate the groundwater model. Using observed climatic data, a water budget method was applied to estimate recharge in different types of land uses. Statistically downscaled future climate scenarios were used as inputs for that same recharge model, which provided data for running SPA under those scenarios. The results show that most of the GCMs used here predict temperature arises over 275,15 K and major monthly rainfall mean changes to take place in the dry season. During wet seasons, those means might experience around 50% decrease. The transient model results indicate that water table variations, derived from around 70% of the climate scenarios, would vary below those measured between 2004 and 2011. Among the thirteen GCMs considered in this work, only four of them predicted more extreme climate scenarios. In some regions of the study area and under these extreme conditions, groundwater surface would decline more than 10 m. Although more optimistic scenarios resulted in an increase of groundwater levels in more than half of ROB, these would cause up to 5 m water table decline. The results reinforce the need for a permanent hydrogeological monitoring, mainly in the GAS recharge areas, along with the development of other climate change impacts assessment works using different downscaling and recharge estimates methods.

A Study of Current World Telecommunications and a Projection of the Future

DTIC Science & Technology

1992-09-01

SOURCE OF FUNDING NUMBERS PROGRAM PROJECT TASK WORK UNIT ELEMENT NO. NO. NO. ACCESSION NO. 11. TITLE (Include Security Classification) A STUDY OF CURRENT...51 b. Integrated Services Digital Network 53 c. Network Switching ...... ........... 54 d. SS7 ...54 Table IX PERCENTAGE OF CO WITH SS7 CAPABILITY FOR THE GROUP OF SEVEN ............. .................. 55 Table X TRENDS, FORECAST IN

Longitudinal Surveys of Australian Youth (LSAY) 1998 Cohort: Wave 12 (2009)--Frequency Tables. Technical Report 58B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 1998 cohort Wave 12 (2009) data set. [For the accompanying questionnaire, "Longitudinal Surveys…

Longitudinal Surveys of Australian Youth (LSAY): 2003 Cohort Wave 7 (2009)--Frequency Tables. Technical Report 57B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2003 cohort Wave 7 (2009) data set. [For the related questionnaire, see ED512164.

Total Quality Management in the United States Army Corps of Engineers

DTIC Science & Technology

1993-05-01

Office. Telephone interview with author, 20 November 1992. Ishikawa , Kaoru (1985). What is Total Quality Control? The Japanese Way. Prentice-Hall, Inc...Organizations ..... 55 Table 13. Ishikawa PDCA Cycle .......................................................... 68 Table 14. TQM Training M atrix...Standards 1008 ( Ishikawa 1985). The Japanese were aware of both the American and British work with standards. The standards were studied by

Large-Scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) Simulations of the Molecular Crystal alphaRDX

DTIC Science & Technology

2013-08-01

potential for HMX / RDX (3, 9). ...................................................................................8 1 1. Purpose This work...6 dispersion and electrostatic interactions. Constants for the SB potential are given in table 1. 8 Table 1. SB potential for HMX / RDX (3, 9...modeling dislocations in the energetic molecular crystal RDX using the Large-Scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) molecular

Modeling Macro-Cognitive Influence on Information Sharing between Members of a Joint Team

DTIC Science & Technology

2006-12-01

enormous role in the completion of this work. My spiritual advisors, David Bray and Vannoy Shaw , helped me to never lost sight of what my true...Table 22. 124 Table 22. Seat One Evaluation Service N M Abs (Dif) - LSD p-Value Air Force 5 4.6000 .328 *0.0252 Army 6 1.6666 -2.48

Longitudinal Surveys of Australian Youth (LSAY) 2009 Cohort: Wave 3 (2011)--Frequency Tables. Technical Report 72B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2012

2012-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2009 cohort Wave 3 (2011) data set. [For the related questionnaire, see ED536306.

Longitudinal Surveys of Australian Youth (LSAY): 2006 Cohort Wave 4 (2009)--Frequency Tables. Technical Report 56B

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

The Longitudinal Surveys of Australian Youth (LSAY) program studies the progress of several groups of young Australians as they move from school into post-secondary education and work. This technical paper contains the frequency tables for the LSAY 2006 cohort Wave 4 (2009) data set. [For the "Longitudinal Surveys of Australian Youth (LSAY):…