Sample records for tablets

  1. Tableting Properties and Compression Models of Labisia pumila Tablets.

    PubMed

    Etti, C J; Yusof, Y A; Chin, N L; Mohd Tahir, S

    2017-03-04

    The tableting properties of Labisia pumila herbal powder, which is well known for its therapeutic benefits was investigated. The herbal powder was compressed into tablets using a stainless steel cylindrical uniaxial die of 13-mm- diameter with compaction pressures ranging from 7 to 25 MPa. Two feed weights, 0.5 and 1.0 g were used to form tablets. Some empirical models were used to describe the compressibility behavior of Labisia pumila tablets. The strength and density of tablets increased with increase in compaction pressure and resulted in reduction in porosity of the tablets. Smaller feeds, higher forces and increase in compaction pressure, contributed to more coherent tablets. These findings can be used to enhance the approach and understanding of tableting properties of Labisia pumila herbal powder tablets.

  2. [Tablets and tablet production - with special reference to Icelandic conditions].

    PubMed

    Skaftason, Jóhannes F; Jóhannesson, Thorkell

    2013-04-01

    Modern tablet compression was instituted in England in 1844 by William Brockedon (1787-1854). The first tablets made according to Brockedon´s procedures contained watersoluble salts and were most likely compressed without expedients. In USA a watershed occurred around 1887 when starch (amylum maydis) was introduced to disperse tablets in aqueous milieu in order to corroborate bioavailability of drugs in the almentary canal. About the same time great advances in tablet production were introduced by the British firm Burroughs Wellcome and Co. In Denmark on the other hand tablet production remained on low scale until after 1920. As Icelandic pharmacies and drug firms modelled themselves mostly upon Danish firms tablet production was first instituted in Iceland around 1930. The first tablet machines in Iceland were hand-driven. More efficent machines came after 1945. Around 1960 three sizeable tablet producers were in Iceland; now there is only one. Numbers of individual tablet species (generic and proprietary) on the market rose from less than 10 in 1913 to 500 in 1965, with wide variations in numbers in between. Tablets have not wiped out other medicinal forms for peroral use but most new peroral drugs have been marketed in the form of tablets during the last decades.

  3. Tablet splitting and weight uniformity of half-tablets of 4 medications in pharmacy practice.

    PubMed

    Tahaineh, Linda M; Gharaibeh, Shadi F

    2012-08-01

    Tablet splitting is a common practice for multiple reasons including cost savings; however, it does not necessarily result in weight-uniform half-tablets. To determine weight uniformity of half-tablets resulting from splitting 4 products available in the Jordanian market and investigate the effect of tablet characteristics on weight uniformity of half-tablets. Ten random tablets each of warfarin 5 mg, digoxin 0.25 mg, phenobarbital 30 mg, and prednisolone 5 mg were weighed and split by 6 PharmD students using a knife. The resulting half-tablets were weighed and evaluated for weight uniformity. Other relevant physical characteristics of the 4 products were measured. The average tablet hardness of the sampled tablets ranged from 40.3 N to 68.9 N. Digoxin, phenobarbital, and prednisolone half-tablets failed the weight uniformity test; however, warfarin half-tablets passed. Digoxin, warfarin, and phenobarbital tablets had a score line and warfarin tablets had the deepest score line of 0.81 mm. Splitting warfarin tablets produces weight-uniform half-tablets that may possibly be attributed to the hardness and the presence of a deep score line. Digoxin, phenobarbital, and prednisolone tablet splitting produces highly weight variable half-tablets. This can be of clinical significance in the case of the narrow therapeutic index medication digoxin.

  4. Angular circulation speed of tablets in a vibratory tablet coating pan.

    PubMed

    Kumar, Rahul; Wassgren, Carl

    2013-03-01

    In this work, a single tablet model and a discrete element method (DEM) computer simulation are developed to obtain the angular circulation speed of tablets in a vibratory tablet coating pan for range of vibration frequencies and amplitudes. The models identify three important dimensionless parameters that influence the speed of the tablets: the dimensionless amplitude ratio (a/R), the Froude number (aω2/g), and the tablet-wall friction coefficient, where a is the peak vibration amplitude at the drum center, ω is the vibration angular frequency, R is the drum radius, and g is the acceleration due to gravity. The models predict that the angular circulation speed of tablets increases with an increase in each of these parameters. The rate of increase in the angular circulation speed is observed to decrease for larger values of a/R. The angular circulation speed reaches an asymptote beyond a tablet-wall friction coefficient value of about 0.4. Furthermore, it is found that the Froude number should be greater than one for the tablets to start circulating. The angular circulation speed increases as Froude number increases but then does not change significantly at larger values of the Froude number. Period doubling, where the motion of the bed is repeated every two cycles, occurs at a Froude number larger than five. The single tablet model, although much simpler than the DEM model, is able to predict the maximum circulation speed (the limiting case for a large value of tablet-wall friction coefficient) as well as the transition to period doubling.

  5. Performance of tablet disintegrants: impact of storage conditions and relative tablet density.

    PubMed

    Quodbach, Julian; Kleinebudde, Peter

    2015-01-01

    Tablet disintegration can be influenced by several parameters, such as storage conditions, type and amount of disintegrant, and relative tablet density. Even though these parameters have been mentioned in the literature, the understanding of the disintegration process is limited. In this study, water uptake and force development of disintegrating tablets are analyzed, as they reveal underlying processes and interactions. Measurements were performed on dibasic calcium phosphate tablets containing seven different disintegrants stored at different relative humidities (5-97%), and on tablets containing disintegrants with different mechanisms of action (swelling and shape recovery), compressed to different relative densities. Disintegration times of tablets containing sodium starch glycolate are affected most by storage conditions, which is displayed in decreased water uptake and force development kinetics. Disintegration times of tablets with a swelling disintegrant are only marginally affected by relative tablet density, whereas the shape recovery disintegrant requires high relative densities for quick disintegration. The influence of relative tablet density on the kinetics of water uptake and force development greatly depends on the mechanism of action. Acquired data allows a detailed analysis of the influence of storage conditions and mechanisms of action on disintegration behavior.

  6. Tablet Use within Medicine

    ERIC Educational Resources Information Center

    Hogue, Rebecca J.

    2013-01-01

    This paper discusses the scholarly literature related to tablet computer use in medicine. Forty-four research-based articles were examined for emerging categories and themes. The most studied uses for tablet computers include: patients using tablets to complete diagnostic survey instruments, medical professionals using tablet computers to view…

  7. INFLUENCE OF TABLET SPLITTING ON CONTENT UNIFORMITY OF LISINOPRIL/ HYDROCHLORTHIAZIDE TABLETS

    PubMed Central

    Vranić, Edina; Uzunović, Alija

    2007-01-01

    Dose-related adverse effects of medications are a major problem in modern medical practice. The “correct” dose, based on drug company guidelines in package inserts, may not be correct for many patients. Tablet splitting or dividing has been an accepted practice for many years as a means of obtaining the prescribed dose of medication. As model tablets for this investigation, two batches of lisinopril-hydrochlorothiazide scored tablets labeled to contain 20/12,5 mg were used. The aim of this study was to establish possible influence of tablet splitting on content uniformity of lisinopril/hydrochlorthiazide tablets. Determination of the content uniformity of lisinopril and hydrochlorthiazide in our batches, was carried out by HPLC method. The results of content uniformity studies for halves of tablets containing combination of lisinopril-hydrochlorthiazide (supposed to contain 50% of stated 20/12,5 mg in the whole tablet) were: 49,60 ±3,29% and 49,29±0,60 % (lisinopril); 50,33±3,50% and 50,69±1,95% (hydrochlorthiazide) for batch I and II, respectively. We can conclude that the results obtained in this study support an option of tablet splitting, which is very important for obtaining the required dosage when a dosage form of the required strength is unavailable, and for better individualization of the therapy PMID:18039191

  8. Dose uniformity of scored and unscored tablets: Application of the FDA Tablet Scoring Guidance for Industry.

    PubMed

    Ciavarella, Anthony; Khan, Mansoor; Gupta, Abhay; Faustino, Patrick

    2016-06-20

    This FDA laboratory study examines the impact of tablet splitting, the effect of tablet splitters, and the presence of a tablet score on the dose uniformity of two model drugs. Whole tablets were purchased from five manufacturers for amlodipine and six for gabapentin. Two splitters were used for each drug product and the gabapentin tablets were also split by hand. Whole and split amlodipine tablets were tested for content uniformity following the general chapter of the United States Pharmacopeia (USP) Uniformity of Dosage Units <905>, which is a requirement of the new FDA Guidance for Industry on tablet scoring. The USP weight variation method was used for gabapentin split tablets based on the recommendation of the guidance. All whole tablets met the USP acceptance criteria for the Uniformity of Dosage Units. Variation in whole tablet content ranged from 0.5-2.1 standard deviation (SD) of the % label claim. Splitting the unscored amlodipine tablets resulted in a significant increase in dose variability of 6.5-25.4 SD when compared to whole tablets. Split tablets from all amlodipine drug products did not meet the USP acceptance criteria for content uniformity. Variation in the weight for gabapentin split tablets was greater than the whole tablets, ranging from 1.3-9.3 SD. All fully scored gabapentin products met the USP acceptance criteria for weight variation. Size, shape, and the presence or absence of a tablet score can affect the content uniformity and weight variation of amlodipine and gabapentin tablets. Tablet splitting produced higher variability. Differences in dose variability and fragmentation were observed between tablet splitters and hand splitting. These results are consistent with the FDA's concerns that tablet splitting "can affect how much drug is present in the split tablet and available for absorption" as stated in the guidance (1). Copyright © 2016, Parenteral Drug Association.

  9. Calcification prevention tablets

    NASA Technical Reports Server (NTRS)

    Lindsay, Geoffrey A.; Hasting, Michael A.; Gustavson, Michael A.

    1991-01-01

    Citric acid tablets, which slowly release citric acid when flushed with water, are under development by the Navy for calcification prevention. The citric acid dissolves calcium carbonate deposits and chelates the calcium. For use in urinals, a dispenser is not required because the tablets are non-toxic and safe to handle. The tablets are placed in the bottom of the urinal, and are consumed in several hundred flushes (the release rate can be tailored by adjusting the formulation). All of the ingredients are environmentally biodegradable. Mass production of the tablets on commercial tableting machines was demonstrated. The tablets are inexpensive (about 75 cents apiece). Incidences of clogged pipes and urinals were greatly decreased in long term shipboard tests. The corrosion rate of sewage collection pipe (90/10 Cu/Ni) in citric acid solution in the laboratory is several mils per year at conditions typically found in traps under the urinals. The only shipboard corrosion seen to date is of the yellow brass urinal tail pieces. While this is acceptable, the search for a nontoxic corrosion inhibitor is underway. The shelf life of the tablets is at least one year if stored at 50 percent relative humidity, and longer if stored in sealed plastic buckets.

  10. A new tablet brittleness index.

    PubMed

    Gong, Xingchu; Sun, Changquan Calvin

    2015-06-01

    Brittleness is one of the important material properties that influences the success or failure of powder compaction. We have discovered that the reciprocal of diametrical elastic strain at fracture is the most suitable tablet brittleness indices (TBIs) for quantifying brittleness of pharmaceutical tablets. The new strain based TBI is supported by both theoretical considerations and a systematic statistical analysis of friability data. It is sufficiently sensitive to changes in both tablet compositions and compaction parameters. For all tested materials, it correctly shows that tablet brittleness increases with increasing tablet porosity for the same powder. In addition, TBI increases with increasing content of a brittle excipient, lactose monohydrate, in the mixtures with a plastic excipient, microcrystalline cellulose. A probability map for achieving less than 1% tablet friability at various combinations of tablet tensile strength and TBI was constructed. Data from marketed tablets validate this probability map and a TBI value of 150 is recommended as the upper limit for pharmaceutical tablets. This TBI can be calculated from the data routinely obtained during tablet diametrical breaking test, which is commonly performed for assessing tablet mechanical strength. Therefore, it is ready for adoption for quantifying tablet brittleness to guide tablet formulation development since it does not require additional experimental work. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Dose Uniformity of Scored and Unscored Tablets: Application of the FDA Tablet Scoring Guidance for Industry.

    PubMed

    Ciavarella, Anthony B; Khan, Mansoor A; Gupta, Abhay; Faustino, Patrick J

    This U.S. Food and Drug Administration (FDA) laboratory study examines the impact of tablet splitting, the effect of tablet splitters, and the presence of a tablet score on the dose uniformity of two model drugs. Whole tablets were purchased from five manufacturers for amlodipine and six for gabapentin. Two splitters were used for each drug product, and the gabapentin tablets were also split by hand. Whole and split amlodipine tablets were tested for content uniformity following the general chapter of the United States Pharmacopeia (USP) Uniformity of Dosage Units <905>, which is a requirement of the new FDA Guidance for Industry on tablet scoring. The USP weight variation method was used for gabapentin split tablets based on the recommendation of the guidance. All whole tablets met the USP acceptance criteria for the Uniformity of Dosage Units. Variation in whole tablet content ranged from 0.5 to 2.1 standard deviation (SD) of the percent label claim. Splitting the unscored amlodipine tablets resulted in a significant increase in dose variability of 6.5-25.4 SD when compared to whole tablets. Split tablets from all amlodipine drug products did not meet the USP acceptance criteria for content uniformity. Variation in the weight for gabapentin split tablets was greater than the whole tablets, ranging from 1.3 to 9.3 SD. All fully scored gabapentin products met the USP acceptance criteria for weight variation. Size, shape, and the presence or absence of a tablet score can affect the content uniformity and weight variation of amlodipine and gabapentin tablets. Tablet splitting produced higher variability. Differences in dose variability and fragmentation were observed between tablet splitters and hand splitting. These results are consistent with the FDA's concerns that tablet splitting can have an effect on the amount of drug present in a split tablet and available for absorption. Tablet splitting has become a very common practice in the United States and throughout

  12. Study of drug release and tablet characteristics of silicone adhesive matrix tablets.

    PubMed

    Tolia, Gaurav; Li, S Kevin

    2012-11-01

    Matrix tablets of a model drug acetaminophen (APAP) were prepared using a highly compressible low glass transition temperature (T(g)) polymer silicone pressure sensitive adhesive (PSA) at various binary mixtures of silicone PSA/APAP ratios. Matrix tablets of a rigid high T(g) matrix forming polymer ethyl cellulose (EC) were the reference for comparison. Drug release study was carried out using USP Apparatus 1 (basket), and the relationship between the release kinetic parameters of APAP and polymer/APAP ratio was determined to estimate the excipient percolation threshold. The critical points attributed to both silicone PSA and EC tablet percolation thresholds were found to be between 2.5% and 5% w/w. For silicone PSA tablets, satisfactory mechanical properties were obtained above the polymer percolation threshold; no cracking or chipping of the tablet was observed above this threshold. Rigid EC APAP tablets showed low tensile strength and high friability. These results suggest that silicone PSA could eliminate issues related to drug compressibility in the formulation of directly compressed oral controlled release tablets of poorly compressible drug powder such as APAP. No routinely used excipients such as binders, granulating agents, glidants, or lubricants were required for making an acceptable tablet matrix of APAP using silicone PSA. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. NMR imaging of high-amylose starch tablets. 2. Effect of tablet size.

    PubMed

    Malveau, Cédric; Baille, Wilms E; Zhu, Xiao Xia; Marchessault, Robert H

    2002-01-01

    Carbohydrate polymers are widely used for pharmaceutical applications such as the controlled release of drugs. The swelling and water mobility in high-amylose starch tablets are important parameters to be determined for these applications. They have been studied at different time intervals by nuclear magnetic resonance imaging (NMRI) after the immersion of the samples in water. These tablets have a hydrophilic matrix, which swells anisotropically and forms a hydrogel in water. NMRI shows clearly the anisotropy of the water penetration and the swelling along the radial and axial dimensions of the tablets. Empirical relationships are established to describe the kinetics of water penetration and swelling of the tablets. Results show that water uptake and tablet swelling strongly depend on the size of the tablets. Gravimetric measurements of water uptake were also performed in comparison with the NMRI results.

  14. Phase transformation in thiamine hydrochloride tablets: Influence on tablet microstructure, physical properties, and performance.

    PubMed

    Chakravarty, Paroma; Suryanarayanan, Raj; Govindarajan, Ramprakash

    2012-04-01

    The objective of this article was to monitor phase transformation in thiamine hydrochloride, from a nonstoichiometric hydrate (NSH) to a hemihydrate (HH), in stored tablets, prepared both by direct compression and wet granulation, and to relate the storage-induced phase transformation with changes in tablet microstructure, physical properties, and performance. Raman spectroscopy revealed complete NSH → HH transformation in tablets, within 30 h of storage at 40°C/75% relative humidity. When the tablets were prepared by wet granulation of NSH alone, there was a marked increase in both tablet volume and hardness on storage. However, when microcrystalline cellulose (MCC) was included in granulation, the resulting stored tablets also exhibited a pronounced increase in disintegration time. In contrast, tablets prepared by dry processing via compression of a NSH-MCC physical mixture did not exhibit any changes in properties, despite the in situ solid form conversion. Scanning electron microscopy revealed growth of needle-like HH crystals in all stored tablets and mercury porosimetry revealed considerable changes in the pore size distribution during storage. Longer storage led to crystal growth (Ostwald ripening), causing further gradual but less dramatic changes in properties. The phase transformation and the complex interparticulate associations in the tablet influenced the changes in tablet microstructure, compact physical properties, and product behavior. Copyright © 2011 Wiley Periodicals, Inc.

  15. Evaluation of the ease of taking mini-tablets compared with other tablet formulations in healthy volunteers.

    PubMed

    Hayakawa, Yoshiyuki; Uchida, Shinya; Namiki, Noriyuki

    2016-03-10

    "Mini-tablets" (MTs) are tablets of diameter≤3mm and have been widely studied and developed. However, reports comparing MTs with other tablet formulations are few. We wished to evaluate the ease of taking a MT quantitatively in comparison with an orally disintegrating mini-tablet (ODMT), conventional tablet (CT) and conventional orally disintegrating tablet (ODT). Four types of tablets were prepared. We prepared tablets of two diameters (3mm for MTs and ODMTs vs. 8mm for CTs and ODTs) and two formulations (MTs and CTs vs. ODMTs and ODTs). Our randomized crossover trial in 18 healthy volunteers (8 men and 10 women; mean age, 22.5years) indicated that the visual analog scale (VAS) score for the ease and amount of water required for intake of MTs was significantly lower than those of CTs. An ODMT required the least amount of water and smallest VAS score for the ease of taking a tablet. Our results showed that the advantage of MTs with regard to the ease of taking and decreased amount of water required was exerted for a unit of dosing comprising <5 tablets. These data suggested the usefulness of MTs and the importance of the number of MTs for comfortable consumption by patients. Copyright © 2015. Published by Elsevier B.V.

  16. How do tablet properties influence swallowing behaviours?

    PubMed

    Yamamoto, Shinya; Taniguchi, Hiroshige; Hayashi, Hirokazu; Hori, Kazuhiro; Tsujimura, Takanori; Nakamura, Yuki; Sato, Hideaki; Inoue, Makoto

    2014-01-01

    Behavioural performance of tablet swallowing was evaluated with different tablet conditions in terms of size, number and surface coating. Four different types of tablets were prepared: small or large, and with or without a surface coating. Fourteen normal male adults were instructed to swallow the prepared tablets with 15 ml of water. The number of tablets in one trial was changed from one to three. To evaluate swallowing and tablet transport, electromyographic activity was recorded in the left suprahyoid muscles, and videofluorographic images were examined. All tablet conditions (size, number and surface coating) affected the swallowing performance in terms of total number of swallows, electromyographic burst patterns and location of remaining tablets. Increases in the size and number of tablets increased the number of swallows and electromyographic burst area and duration. In addition, all of these parameters increased while swallowing tablets without a coating compared with tablets with a coating. Location of the remaining tablets was mainly within the mouth. This study only clarified the normal pattern of tablet swallowing under several conditions in healthy subjects, but the results may facilitate comprehensive evaluation and treatment planning in terms of administering medication to dysphagic patients. © 2013 Royal Pharmaceutical Society.

  17. Review of bilayer tablet technology.

    PubMed

    Abebe, Admassu; Akseli, Ilgaz; Sprockel, Omar; Kottala, Niranjan; Cuitiño, Alberto M

    2014-01-30

    Therapeutic strategies based on oral delivery of bilayer (and multilayer) tablets are gaining more acceptance among brand and generic products due to a confluence of factors including advanced delivery strategies, patient compliance and combination therapy. Successful manufacturing of these ever more complex systems needs to overcome a series of challenges from formulation design to tablet press monitoring and control. This article provides an overview of the state-of-the-art of bilayer tablet technology, highlighting the main benefits of this type of oral dosage forms while providing a description of current challenges and advances toward improving manufacturing practices and product quality. Several aspects relevant to bilayer tablet manufacturing are addressed including material properties, lubrication, layer ordering, layer thickness, layer weight control, as well as first and final compression forces. A section is also devoted to bilayer tablet characterization that present additional complexities associated with interfaces between layers. The available features of the manufacturing equipment for bilayer tablet production are also described indicating the different strategies for sensing and controls offered by bilayer tablet press manufacturers. Finally, a roadmap for bilayer tablet manufacturing is advanced as a guideline to formulation design and selection of process parameters and equipment. Copyright © 2013 Elsevier B.V. All rights reserved.

  18. Effect of repeated compaction of tablets on tablet properties and work of compaction using an instrumented laboratory tablet press.

    PubMed

    Gamlen, Michael John Desmond; Martini, Luigi G; Al Obaidy, Kais G

    2015-01-01

    The repeated compaction of Avicel PH101, dicalcium phosphate dihydrate (DCP) powder, 50:50 DCP/Avicel PH101 and Starch 1500 was studied using an instrumented laboratory tablet press which measures upper punch force, punch displacement and ejection force and operates using a V-shaped compression profile. The measurement of work compaction was demonstrated, and the test materials were ranked in order of compaction behaviour Avicel PH101 > DCP/Avicel PH101 > Starch > DCP. The behaviour of the DCP/Avicel PH101 mixture was distinctly non-linear compared with the pure components. Repeated compaction and precompression had no effect on the tensile fracture strength of Avicel PH101 tablets, although small effects on friability and disintegration time were seen. Repeated compaction and precompression reduced the tensile strength and the increased disintegration time of the DCP tablets, but improved the strength and friability of Starch 1500 tablets. Based on the data reported, routine laboratory measurement of tablet work of compaction may have potential as a critical quality attribute of a powder blend for compression. The instrumented press was suitable for student use with minimal supervisor input.

  19. Can Tablet Computers Enhance Faculty Teaching?

    PubMed Central

    Narayan, Aditee P.; Whicker, Shari A.; Benjamin, Robert W.; Hawley, Jeffrey; McGann, Kathleen A.

    2015-01-01

    Background Learner benefits of tablet computer use have been demonstrated, yet there is little evidence regarding faculty tablet use for teaching. Objective Our study sought to determine if supplying faculty with tablet computers and peer mentoring provided benefits to learners and faculty beyond that of non–tablet-based teaching modalities. Methods We provided faculty with tablet computers and three 2-hour peer-mentoring workshops on tablet-based teaching. Faculty used tablets to teach, in addition to their current, non–tablet-based methods. Presurveys, postsurveys, and monthly faculty surveys assessed feasibility, utilization, and comparisons to current modalities. Learner surveys assessed perceived effectiveness and comparisons to current modalities. All feedback received from open-ended questions was reviewed by the authors and organized into categories. Results Of 15 eligible faculty, 14 participated. Each participant attended at least 2 of the 3 workshops, with 10 to 12 participants at each workshop. All participants found the workshops useful, and reported that the new tablet-based teaching modality added value beyond that of current teaching methods. Respondents developed the following tablet-based outputs: presentations, photo galleries, evaluation tools, and online modules. Of the outputs, 60% were used in the ambulatory clinics, 33% in intensive care unit bedside teaching rounds, and 7% in inpatient medical unit bedside teaching rounds. Learners reported that common benefits of tablet computers were: improved access/convenience (41%), improved interactive learning (38%), and improved bedside teaching and patient care (13%). A common barrier faculty identified was inconsistent wireless access (14%), while no barriers were identified by the majority of learners. Conclusions Providing faculty with tablet computers and having peer-mentoring workshops to discuss their use was feasible and added value. PMID:26221443

  20. Can Tablet Computers Enhance Faculty Teaching?

    PubMed

    Narayan, Aditee P; Whicker, Shari A; Benjamin, Robert W; Hawley, Jeffrey; McGann, Kathleen A

    2015-06-01

    Learner benefits of tablet computer use have been demonstrated, yet there is little evidence regarding faculty tablet use for teaching. Our study sought to determine if supplying faculty with tablet computers and peer mentoring provided benefits to learners and faculty beyond that of non-tablet-based teaching modalities. We provided faculty with tablet computers and three 2-hour peer-mentoring workshops on tablet-based teaching. Faculty used tablets to teach, in addition to their current, non-tablet-based methods. Presurveys, postsurveys, and monthly faculty surveys assessed feasibility, utilization, and comparisons to current modalities. Learner surveys assessed perceived effectiveness and comparisons to current modalities. All feedback received from open-ended questions was reviewed by the authors and organized into categories. Of 15 eligible faculty, 14 participated. Each participant attended at least 2 of the 3 workshops, with 10 to 12 participants at each workshop. All participants found the workshops useful, and reported that the new tablet-based teaching modality added value beyond that of current teaching methods. Respondents developed the following tablet-based outputs: presentations, photo galleries, evaluation tools, and online modules. Of the outputs, 60% were used in the ambulatory clinics, 33% in intensive care unit bedside teaching rounds, and 7% in inpatient medical unit bedside teaching rounds. Learners reported that common benefits of tablet computers were: improved access/convenience (41%), improved interactive learning (38%), and improved bedside teaching and patient care (13%). A common barrier faculty identified was inconsistent wireless access (14%), while no barriers were identified by the majority of learners. Providing faculty with tablet computers and having peer-mentoring workshops to discuss their use was feasible and added value.

  1. Investigation of the effect of tablet surface area/volume on drug release from hydroxypropylmethylcellulose controlled-release matrix tablets.

    PubMed

    Reynolds, Thomas D; Mitchell, Shawn A; Balwinski, Karen M

    2002-04-01

    The purpose of this study was to investigate the influence of tablet surface area/volume (SA/Vol) on drug release from controlled-release matrix tablets containing hydroxypropylmethylcellulose (HPMC). Soluble drugs (promethazine HCl, diphenhydramine HCl, and propranolol HCl) were utilized in this study to give predominantly diffusion-controlled release. Drug release from HPMC matrix tablets with similar values of SA/Vol was comparable within the same tablet shape (i.e., flat-faced round tablets) and among different shapes (i.e., oval, round concave, flat-faced beveled-edge, and flat-faced round tablets). Tablets having the same surface area but different SA/Vol values did not result in similar drug release; tablets with larger SA/Vol values hadfaster release profiles. Utility of SA/Vol to affect drug release was demonstrated by changing drug doses, and altering tablet shape to adjust SA/Vol. When SA/Vol was held constant, similar release profiles were obtained with f2 metric values greater than 70. Thus, surface area/volume is one of the key variables in controlling drug release from HPMC matrix tablets. Proper use of this variable has practical application by formulators who may need to duplicate drug release profiles from tablets of different sizes and different shapes.

  2. Microstructure of Tablet-Pharmaceutical Significance, Assessment, and Engineering.

    PubMed

    Sun, Changquan Calvin

    2017-05-01

    To summarize the microstructure - property relationship of pharmaceutical tablets and approaches to improve tablet properties through tablet microstructure engineering. The main topics reviewed here include: 1) influence of material properties and manufacturing process parameters on the evolution of tablet microstructure; 2) impact of tablet structure on tablet properties; 3) assessment of tablet microstructure; 4) development and engineering of tablet microstructure. Microstructure plays a decisive role on important pharmaceutical properties of a tablet, such as disintegration, drug release, and mechanical strength. Useful information on mechanical properties of a powder can be obtained from analyzing tablet porosity-pressure data. When helium pycnometry fails to accurately measure true density of a water-containing powder, non-linear regression of tablet density-pressure data is a useful alternative method. A component that is more uniformly distributed in a tablet generally exerts more influence on the overall tablet properties. During formulation development, it is highly recommended to examine the relationship between any property of interest and tablet porosity when possible. Tablet microstructure can be engineered by judicious selection of formulation composition, including the use of the optimum solid form of the drug and appropriate type and amount of excipients, and controlling manufacturing process.

  3. Preparation of bilayer-core osmotic pump tablet by coating the indented core tablet.

    PubMed

    Liu, Longxiao; Xu, Xiangning

    2008-03-20

    In this paper, a bilayer-core osmotic pump tablet (OPT) which does not require laser drilling to form the drug delivery orifice is described. The bilayer-core consisted of two layers: (a) push layer and (b) drug layer, and was made with a modified upper tablet punch, which produced an indentation at the center of the drug layer surface. The indented tablets were coated by using a conventional pan-coating process. Although the bottom of the indentation could be coated, the side face of the indentation was scarcely sprayed by the coating solution and this part of the tablet remained at least partly uncoated leaving an aperture from which drug release could occur. Nifedipine was selected as the model drug. Sodium chloride was used as osmotic agent, polyvinylpyrrolidone as suspending agent and croscarmellose sodium as expanding agent. The indented core tablet was coated by ethyl cellulose as semipermeable membrane containing polyethylene glycol 400 for controlling the membrane permeability. The formulation of core tablet was optimized by orthogonal design and the release profiles of various formulations were evaluated by similarity factor (f(2)). It was found that the optimal OPT was able to deliver nifedipine at an approximate zero-order up to 24 h, independent on both release media and agitation rates. The preparation of bilayer-core OPT was simplified by coating the indented core tablet, by which sophisticated technology of the drug layer identification and laser drilling could be eliminated. It might be promising in the field of preparation of bilayer-core OPT.

  4. Pharmaceutical and analytical evaluation of triphalaguggulkalpa tablets

    PubMed Central

    Savarikar, Shreeram S.; Barbhind, Maneesha M.; Halde, Umakant K.; Kulkarni, Alpana P.

    2011-01-01

    Aim of the Study: Development of standardized, synergistic, safe and effective traditional herbal formulations with robust scientific evidence can offer faster and more economical alternatives for the treatment of disease. The main objective was to develop a method of preparation of guggulkalpa tablets so that the tablets meet the criteria of efficacy, stability, and safety. Materials and Methods: Triphalaguggulkalpa tablet, described in sharangdharsanhita and containing guggul and triphala powder, was used as a model drug. Preliminary experiments on marketed triphalaguggulkalpa tablets exhibited delayed in vitro disintegration that indicated probable delayed in vivo disintegration. The study involved preparation of triphalaguggulkalpa tablets by Ayurvedic text methods and by wet granulation, dry granulation, and direct compression method. The tablets were evaluated for loss on drying, volatile oil content, % solubility, and steroidal content. The tablets were evaluated for performance tests like weight variation, disintegration, and hardness. Results: It was observed that triphalaguggulkalpa tablets, prepared by direct compression method, complied with the hardness and disintegration tests, whereas tablets prepared by Ayurvedic text methods failed. Conclusion: Direct compression is the best method of preparing triphalaguggulkalpa tablets. PMID:21731383

  5. COMPARISON OF HYDROCORTISONE 10 MG TABLETS: TABLET HARDNESS OPTIMISED FOR ADULT USE HAS NEGATIVE CONSEQUENCES FOR PAEDIATRIC USE.

    PubMed

    Saimbi, Sarina; Madden, Valerie; Stirling, Heather; Yahyouche, Asma; Batchelor, Hannah

    2016-09-01

    Children's medicines are not always readily available as an age appropriate product and manipulation of adult products is often required. Recently the commercial manufacturing process for 10 mg hydrocortisone tablets has changed and the compression force increased due to tablets fracturing on removal from the blister pack. However, this change led to parents of children requiring hydrocortisone reporting that the tablets were more difficult to manipulate.This study evaluated 10 mg hydrocortisone tablets for their suitability for manipulation in order to deliver an appropriate dose to children (2 mg dose). The physical properties of tablets with the old and new compression force were compared as well as the accuracy of obtaining the paediatric dose. The tablets compared were hydrocortisone Auden 10 mg tablets (Brand A, PL16876/002)-these are the newer, harder tablets- and hydrocortisone 10 mg tablets (Brand B, PL17507/0097). Tablet physical properties including friability (Copley FRV200) and tablet hardness (Copley TBF1000) were compared. The accuracy of split doses (halve and quarter tablets) were recorded on a Sartorius analytical balance. The accuracy of the 2 mg paediatric dosing was assessed by crushing the tablet, adding 10 mL of water and extracting 2 mL. The concentration was measured using UV analysis (Jenway Genova Plus) according to a calibration curve (wavelength=246 nm). Two devices were used to crush the tablets: a spoon onto a plate and a commercially available crushing device (Apothecary Ezy Crush Pill Crusher With Ergo Grip). As anticipated Brand A tablets were harder (51.85 ±5.1 N) compared to Brand B (30.99±4.1 N). Brand A tablets passed the friability testing with <1% weight loss whereas Brand B failed as 5 tablets broke during testing.The accuracy of split doses using the score lines to halve and quarter the tablets showed that Brand A were generally better with smaller ranges for both halves (Range for A=41-55%; B=29

  6. A critical review on tablet disintegration.

    PubMed

    Quodbach, Julian; Kleinebudde, Peter

    2016-09-01

    Tablet disintegration is an important factor for drug release and can be modified with excipients called tablet disintegrants. Tablet disintegrants act via different mechanisms and the efficacy of these excipients is influenced by various factors. In this review, the existing literature on tablet disintegration is critically reviewed. Potential disintegration mechanisms, as well as impact factors on the disintegration process will be discussed based on experimental evidence. Search terms for Scopus and Web of Science included "tablet disintegration", "mechanism tablet disintegration", "superdisintegrants", "disintegrants", "swelling force", "disintegration force", "disintegration mechanisms", as well as brand names of commonly applied superdisintegrants. References of identified papers were screened as well. Experimental data supports swelling and shape recovery as main mechanisms of action of disintegrants. Other tablet excipients and different manufacturing techniques greatly influence the disintegration process. The use of different excipients, experimental setups and manufacturing techniques, as well as the demand for original research led to a distinct patchwork of knowledge. Broader, more systematic approaches are necessary not only to structure the past but also future findings.

  7. Assessment of Tablet Surface Hardness by Laser Ablation and Its Correlation With the Erosion Tendency of Core Tablets.

    PubMed

    Narang, Ajit S; Breckenridge, Lydia; Guo, Hang; Wang, Jennifer; Wolf, Abraham Avi; Desai, Divyakant; Varia, Sailesh; Badawy, Sherif

    2017-01-01

    Surface erosion of uncoated tablets results in processing problems such as dusting and defects during coating and is governed by the strength of particle bonding on tablet surface. In this study, the correlation between dusting tendency of tablets in a coating pan with friability and laser ablation surface hardness was assessed using tablets containing different concentrations of magnesium stearate and tartaric acid. Surface erosion propensity of different batches was evaluated by assessing their dusting tendency in the coating pan. In addition, all tablets were analyzed for crushing strength, friability, modified friability test using baffles in the friability apparatus, and weight loss after laser ablation. Tablets with similar crushing strength showed differences in their surface erosion and dusting tendency when rotated in a coating pan. These differences did not correlate well with tablet crushing strength or friability but did show reasonably good correlation with mass loss after laser ablation. These results suggest that tablet surface mass loss by laser ablation can be used as a minipiloting (small-scale) tool to assess tablet surface properties during early stages of drug product development to assess the risk of potential large-scale manufacturing issues. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  8. 21 CFR 520.1284 - Sodium liothyronine tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Sodium liothyronine tablets. 520.1284 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1284 Sodium liothyronine tablets. (a) Specifications. Sodium liothyronine tablets consist of tablets intended for oral...

  9. 21 CFR 520.1284 - Sodium liothyronine tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium liothyronine tablets. 520.1284 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1284 Sodium liothyronine tablets. (a) Specifications. Sodium liothyronine tablets consist of tablets intended for oral...

  10. 21 CFR 520.1284 - Sodium liothyronine tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Sodium liothyronine tablets. 520.1284 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1284 Sodium liothyronine tablets. (a) Specifications. Sodium liothyronine tablets consist of tablets intended for oral...

  11. 21 CFR 520.1284 - Sodium liothyronine tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Sodium liothyronine tablets. 520.1284 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1284 Sodium liothyronine tablets. (a) Specifications. Sodium liothyronine tablets consist of tablets intended for oral...

  12. 21 CFR 520.1445 - Milbemycin oxime tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Milbemycin oxime tablets. 520.1445 Section 520... tablets. (a) Specifications—(1) Dogs. Each tablet contains 2.3, 5.75, 11.5, or 23.0 milligrams of milbemycin oxime. (2) Cats. Each tablet contains 5.75, 11.5, or 23.0 milligrams of milbemycin oxime. (b...

  13. Improving Powder Tableting Performance through Materials Engineering

    NASA Astrophysics Data System (ADS)

    Osei-Yeboah, Frederick

    Adequate mechanical strength is a critical requirement to the successful development of a tablet product. Before tablet compression, powders are often engineered by various processes including wet granulation and surface coating, which may improve or adversely affect the powder tableting performance. Such effects, commonly, result from a change in either particle mechanical properties or particulate (size, shape) properties. In this work, tableting performance is interpreted based on the qualitative bonding-area and bonding-strength (BABS) model. The tabletability of the microcrystalline cellulose (MCC) granules deteriorates rapidly with increasing amount of granulating water and eventually leads to over-granulation at high water level. Granule surface smoothing, size enlargement, granule densification and shape rounding are the dominant factors leading to the tabletability reduction of plastic MCC. Incorporation of increasing amounts of brittle excipients, such as lactose or dibasic calcium phosphate reduces the rate of tabletability reduction by promoting more granule fragmentation, introducing more surface area available for bonding. When a sufficient amount of brittle excipients is used, the over-granulation phenomenon can be eliminated. Surface coating of incompressible MCC pellets with highly bonding polymer leads to sufficient surface deformation and adhesion to enable direct compression of the pellets into tablets of adequate mechanical strength. This improvement is enhanced by the presence of moisture, which plasticizes the polymer to allow the development of a larger bonding area between coated pellets. The relationship between mechanical properties and tableting behavior is systematically investigated in polymeric composites using celecoxib-polyvinylpyrrolidone vinyl acetate solid dispersions. Mechanical properties such as indentation hardness of the solid dispersions were measured using nanoindentation. Incorporation of celecoxib up to 60% by weight

  14. 21 CFR 520.1310 - Marbofloxacin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Marbofloxacin tablets. 520.1310 Section 520.1310... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1310 Marbofloxacin tablets. (a) Specifications. Each tablet contains 25, 50, 100, or 200 milligrams (mg) marbofloxacin. (b...

  15. 21 CFR 520.2330 - Sulfisoxazole tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfisoxazole tablets. 520.2330 Section 520.2330... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.2330 Sulfisoxazole tablets. (a) Specifications. Each tablet contains 260 milligrams (4 grains) of sulfisoxazole. (b) Sponsor. See...

  16. 21 CFR 520.370 - Cefpodoxime tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Cefpodoxime tablets. 520.370 Section 520.370 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.370 Cefpodoxime tablets. (a) Specifications. Each tablet contains cefpodoxime proxetil equivalent to 100 or 200 milligrams (mg) cefpodoxime...

  17. 21 CFR 520.1380 - Methocarbamol tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methocarbamol tablets. 520.1380 Section 520.1380... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1380 Methocarbamol tablets. (a) Chemical name. 3-(O-Methoxyphenoxy)-1,2-propanediol 1-carbamate. (b) Specifications. Each tablet...

  18. Evaluation of the performance characteristics of bilayer tablets: Part II. Impact of environmental conditions on the strength of bilayer tablets.

    PubMed

    Kottala, Niranjan; Abebe, Admassu; Sprockel, Omar; Bergum, James; Nikfar, Faranak; Cuitiño, Alberto M

    2012-12-01

    Ambient air humidity and temperature are known to influence the mechanical strength of tablets. The objective of this work is to understand the influence of processing parameters and environmental conditions (humidity and temperature) on the strength of bilayer tablets. As part of this study, bilayer tablets were compressed with different layer ratios, dwell times, layer sequences, material properties (plastic and brittle), first and second layer forces, and lubricant concentrations. Compressed tablets were stored in stability chambers controlled at predetermined conditions (40C/45%RH, 40C/75%RH) for 1, 3, and 5 days. The axial strength of the stored tablets was measured and a statistical model was developed to determine the effects of the aforementioned factors on the strength of bilayer tablets. As part of this endeavor, a full 3 × 2(4) factorial design was executed. Responses of the experiments were analyzed using PROC GLM of SAS (SAS Institute Inc, Cary, North Carolina, USA). A model was fit using all the responses to determine the significant interactions (p < 0.05). Results of this study indicated that storage conditions and storage time have significant impact on the strength of bilayer tablets. For Avicel-lactose and lactose-Avicel tablets, tablet strength decreased with the increasing humidity and storage time. But for lactose-lactose tablets, due to the formation of solid bridges upon storage, an increase in tablet strength was observed. Significant interactions were observed between processing parameters and storage conditions on the strength of bilayer tablets.

  19. Multiple-layer compression-coated tablets: formulation and humidity studies of novel chewable amoxicillin/clavulanate tablet formulations.

    PubMed

    Wardrop, J; Jaber, A B; Ayres, J W

    1998-08-01

    The purpose of this study was to produce novel multiple-layer, compression-coated, chewable tablet formulations containing amoxicillin trihydrate, and clavulanic acid as potassium clavulanate, and to test in vitro dissolution characteristics and the effect of humidity stability compared to Augmentin chewable tablets as a reference. Double- and triple-layer tablets were manufactured on a laboratory scale by multiple-layer dry compression, and dissolution profiles of both active ingredients were determined. Tablets were subjected to stability evaluation in laboratory-scale humidity tanks maintained at constant humidity. Assay of content was determined by HPLC or UV spectroscopy. Physical characteristics of the powder mixture, such as angle of repose, and of tablets for hardness and friability, were also determined. Chewable tablets showed similar dissolution profiles in vitro for both active ingredients, compared to the marketed reference, Augmentin. The stability of clavulanic acid, but not amoxicillin, was increased in the novel triple or bilayer formulation. The tablets showed suitable friability, hardness, and angle of repose for starting materials to suggest that industrial scale-up is feasible. This approach to formulation of drugs containing multiple or moisture-sensitive ingredients has been shown to increase the stability of the central core drug without changing the dissolution pattern of the active ingredients. This formulation is expected to be bioequivalent in vivo based on these in vitro results.

  20. Using a Virtual Tablet Machine to Improve Student Understanding of the Complex Processes Involved in Tablet Manufacturing.

    PubMed

    Mattsson, Sofia; Sjöström, Hans-Erik; Englund, Claire

    2016-06-25

    Objective. To develop and implement a virtual tablet machine simulation to aid distance students' understanding of the processes involved in tablet production. Design. A tablet simulation was created enabling students to study the effects different parameters have on the properties of the tablet. Once results were generated, students interpreted and explained them on the basis of current theory. Assessment. The simulation was evaluated using written questionnaires and focus group interviews. Students appreciated the exercise and considered it to be motivational. Students commented that they found the simulation, together with the online seminar and the writing of the report, was beneficial for their learning process. Conclusion. According to students' perceptions, the use of the tablet simulation contributed to their understanding of the compaction process.

  1. Using a Virtual Tablet Machine to Improve Student Understanding of the Complex Processes Involved in Tablet Manufacturing

    PubMed Central

    Sjöström, Hans-Erik; Englund, Claire

    2016-01-01

    Objective. To develop and implement a virtual tablet machine simulation to aid distance students’ understanding of the processes involved in tablet production. Design. A tablet simulation was created enabling students to study the effects different parameters have on the properties of the tablet. Once results were generated, students interpreted and explained them on the basis of current theory. Assessment. The simulation was evaluated using written questionnaires and focus group interviews. Students appreciated the exercise and considered it to be motivational. Students commented that they found the simulation, together with the online seminar and the writing of the report, was beneficial for their learning process. Conclusion. According to students’ perceptions, the use of the tablet simulation contributed to their understanding of the compaction process. PMID:27402990

  2. Relationships between response surfaces for tablet characteristics of placebo and API-containing tablets manufactured by direct compression method.

    PubMed

    Hayashi, Yoshihiro; Tsuji, Takahiro; Shirotori, Kaede; Oishi, Takuya; Kosugi, Atsushi; Kumada, Shungo; Hirai, Daijiro; Takayama, Kozo; Onuki, Yoshinori

    2017-10-30

    In this study, we evaluated the correlation between the response surfaces for the tablet characteristics of placebo and active pharmaceutical ingredient (API)-containing tablets. The quantities of lactose, cornstarch, and microcrystalline cellulose were chosen as the formulation factors. Ten tablet formulations were prepared. The tensile strength (TS) and disintegration time (DT) of tablets were measured as tablet characteristics. The response surfaces for TS and DT were estimated using a nonlinear response surface method incorporating multivariate spline interpolation, and were then compared with those of placebo tablets. A correlation was clearly observed for TS and DT of all APIs, although the value of the response surfaces for TS and DT was highly dependent on the type of API used. Based on this knowledge, the response surfaces for TS and DT of API-containing tablets were predicted from only two and four formulations using regression expression and placebo tablet data, respectively. The results from the evaluation of prediction accuracy showed that this method accurately predicted TS and DT, suggesting that it could construct a reliable response surface for TS and DT with a small number of samples. This technique assists in the effective estimation of the relationships between design variables and pharmaceutical responses during pharmaceutical development. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. 21 CFR 520.455 - Clomipramine tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Clomipramine tablets. 520.455 Section 520.455 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.455 Clomipramine tablets. (a) Specifications. Each tablet contains 5, 20, 40, or 80 milligrams (mg) clomipramine hydrochloride. (b) Sponsor...

  4. Touch Screen Tablets and Emergent Literacy

    ERIC Educational Resources Information Center

    Neumann, Michelle M.; Neumann, David L.

    2014-01-01

    The use of touch screen tablets by young children is increasing in the home and in early childhood settings. The simple tactile interface and finger-based operating features of tablets may facilitate preschoolers' use of tablet application software and support their educational development in domains such as literacy. This article reviews…

  5. 21 CFR 520.2088 - Roxarsone tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Roxarsone tablets. 520.2088 Section 520.2088 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.2088 Roxarsone tablets. (a)(1) Specifications. Each tablet contains 36 milligrams of roxarsone (3-nitro-4-hydroxyphenylarsonic acid). (2...

  6. 21 CFR 520.1870 - Praziquantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Praziquantel tablets. 520.1870 Section 520.1870... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1870 Praziquantel tablets. (a) Specifications. Each tablet contains: (1) 34 milligrams (mg) praziquantel. (2) 11.5 or 23 mg praziquantel. (b...

  7. Bioequivalence study of levothyroxine tablets compared to reference tablets and an oral solution.

    PubMed

    Koytchev, Rossen; Lauschner, Reinhard

    2004-01-01

    The study was designed to evaluate the bioequivalence of three levothyroxine sodium (CAS 51-48-9) formulations, i.e. a test and a reference tablet and an oral solution. A bioequivalence study was carried out in 25 healthy volunteers, who were administered a single dose of 600 microg levothyroxine in the form of the test formulation (levothyroxine sodium tablets 200 microg; Eferox), the originator product, and an oral solution. The trial was performed in one study center according to an open, randomized, three-way cross-over design with wash-out periods of 35 days between administration. Blood samples were taken up to 48 h post dose, the plasma was separated and the concentrations of levothyroxine and triiodothyronine were determined by radioimmunoassay with I125 labeling method. The levothyroxine mean Cmax were 112.0+/-17.3 ng/ml, 113.4+/-18.5 ng/ ml and 111.3+/-15.1 ng/ml, while the mean AUC0-24 were 2263.7+/-332.8 ng x h/ ml, 2307.3+/-351.3 ng x h/ml and 2286.1+/-331.0 ng x h/ml for the test and reference tablets as well as for the oral solution, respectively. No significant differences were found of principal pharmacokinetic parameters between the studied formulations. The 90%-confidence interval for the primary target parameters, intra-individual ratios of AUC0-24 and Cmax of levothyroxine were within the acceptance ranges for bioequivalence trials, i.e. AUC0-24 0.954-1.016 and 0.966-1.011 as well as Cmax 0.948-1.027 and 0.968-1.032 for test tablets versus reference tablets and the oral solution, respectively. Similar results were observed for triiodothyronine. In the light of the present study it can be concluded that the levothyroxine test tablet is bioequivalent to the reference formulation in respect of extent and rate of absorption. The results of the present trial confirm the findings of a previous study, performed under steady-state conditions with Eferox tablets 100 microg in patients without thyroid function.

  8. Quantitative Appearance Inspection for Film Coated Tablets.

    PubMed

    Yoshino, Hiroyuki; Yamashita, Kazunari; Iwao, Yasunori; Noguchi, Shuji; Itai, Shigeru

    2016-01-01

    The decision criteria for the physical appearance of pharmaceutical products are subjective and qualitative means of evaluation that are based entirely on human interpretation. In this study, we have developed a comprehensive method for the quantitative analysis of the physical appearance of film coated tablets. Three different kinds of film coated tablets with considerable differences in their physical appearances were manufactured as models, and their surface roughness, contact angle, color measurements and physicochemical properties were investigated as potential characteristics for the quantitative analysis of their physical appearance. All of these characteristics were useful for the quantitative evaluation of the physical appearances of the tablets, and could potentially be used to establish decision criteria to assess the quality of tablets. In particular, the analysis of the surface roughness and film coating properties of the tablets by terahertz spectroscopy allowed for an effective evaluation of the tablets' properties. These results indicated the possibility of inspecting the appearance of tablets during the film coating process.

  9. 21 CFR 520.816 - Epsiprantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Epsiprantel tablets. 520.816 Section 520.816 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.816 Epsiprantel tablets. (a) Specifications. Each tablet contains either 12.5, 25, 50, or 100 milligrams of epsiprantel. (b) Sponsor. See No...

  10. 21 CFR 520.312 - Carnidazole tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Carnidazole tablets. 520.312 Section 520.312 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.312 Carnidazole tablets. (a) Specifications. Each tablet contains 10 milligrams of carnidazole. (b) Sponsor. See 053923 in § 510.600(c) of...

  11. 21 CFR 520.1451 - Moxidectin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Moxidectin tablets. 520.1451 Section 520.1451 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1451 Moxidectin tablets. (a) Specifications. Each tablet contains 30, 68, or 136 micrograms of moxidectin. (b) Sponsor. See No. 000856 in...

  12. Ghost tablet in feces.

    PubMed

    Iwamuro, Masaya; Morishita, Yosuke; Urata, Haruo; Okada, Hiroyuki

    2017-12-01

    Recently, we encountered a female patient who identified the presence of a ghost tablet in her fecal matter. Interestingly, although the patient was prescribed potassium chloride capsules, elemental composition analysis by energy-dispersive X-ray spectroscopy was unable to detect the presence of either potassium or chloride in the fecal tablet remnant.

  13. 21 CFR 520.1288 - Lufenuron tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Lufenuron tablets. 520.1288 Section 520.1288 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1288 Lufenuron tablets. (a) Specifications—(1) Tablets containing 45, 90, 204.9, or 409.8 milligrams (mg) lufenuron for use as in paragraphs...

  14. 21 CFR 520.804 - Enalapril tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Enalapril tablets. 520.804 Section 520.804 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.804 Enalapril tablets. (a) Specifications. Each tablet contains either 1.0, 2.5, 5.0, 10.0, or 20.0 milligrams of enalapril maleate. (b...

  15. 21 CFR 520.1900 - Primidone tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Primidone tablets. 520.1900 Section 520.1900 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1900 Primidone tablets. (a) Specifications. Each tablet contains 50 or 250 milligrams of primidone. (b) Sponsor. See No. 000010 in § 510.600...

  16. 21 CFR 520.1510 - Nitenpyram tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Nitenpyram tablets. 520.1510 Section 520.1510 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1510 Nitenpyram tablets. (a) Specifications. Each tablet contains 11.4 or 57 milligrams (mg) nitenpyram. (b) Sponsor. See No. 058198 in § 510...

  17. 21 CFR 520.812 - Enrofloxacin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Enrofloxacin tablets. 520.812 Section 520.812 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.812 Enrofloxacin tablets. (a) Specifications. Each tablet contains either 22.7, 68.0, or 136.0 milligrams of enrofloxacin. (b) Sponsor. See No...

  18. 'Tablet burden' in patients with metastatic breast cancer.

    PubMed

    Milic, Marina; Foster, Anna; Rihawi, Karim; Anthoney, Alan; Twelves, Chris

    2016-03-01

    The implications for patients with cancer, of the 'tablet burden' resulting from increasing use of oral anticancer drugs and medication for co-morbidities have not previously been well explored. We sought to (i) quantify tablet burden in women with metastatic breast cancer (MBC), (ii) establish which groups of drug contribute most to this burden and (iii) gain insight into patients' attitudes towards oral anti-cancer treatment. One hundred patients with MBC anonymously completed a questionnaire describing their medication histories and attitudes towards their tablets. The patients (mean age 60, range 31-95) were all female and taking a median of six tablets (range 0-31) daily; 37 patients were taking >10 tablets. Oral anticancer treatment constituted the category of treatment taken by the highest proportion of patients, followed by symptomatic cancer treatments, proton pump inhibitors and cardiovascular medication. Numerically, however, symptomatic drugs accounted for 44% of all tablets and specific anti-cancer treatment for 15%; medication not directly related to the cancer accounted for the remaining 40% of tablets. A quarter of patients reported inconvenience in taking their tablets, the main reason being tablet size and one third reported forgetting their tablets at least once a week. Nearly two thirds of patients expressing a preference favoured oral anticancer treatment, the commonest reason being greater convenience. Tablet burden is considerable for many patients with MBC and can be problematic. A significant proportion of tablets represent treatment for co-morbidities, the significance of which may be questionable in women with MBC. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Tablet telerounding.

    PubMed

    Kaczmarek, Bartosz F; Trinh, Quoc-Dien; Menon, Mani; Rogers, Craig G

    2012-12-01

    To evaluate the feasibility of remote rounding using commercially available standard tablets with videoconferencing system and assess patient satisfaction. Thirty-two patients with at least 2 postoperative days of hospital stay after robotic urologic procedures were included in the study. On the first postoperative day, the physician-patient encounter was performed as telerounding with videoconferencing due to the physician's duties scheduled in another affiliated hospital. On the second day, the personal bedside encounter took place. The tablet we used was an iPad2 (Apple, iOS 5.1; Apple, Cupertino, CA) with a videoconferencing application. A telerounding satisfaction survey was fulfilled by all patients on the touchscreen of the tablet. Average time of telerounding encounter was 4.5 minutes (range, 1.0-13.5 minutes), average age of the patient was 57.7 years (range, 19-80 years), and 19 were men (59%). Patients expressed a high level of satisfaction with 91% of patients stating that their care was better using telerounding and 97% of patients stating that telerounding should be a regular part of patient care in the hospital. Additionally, 94% of patients stated that they could easily communicate with their doctor over the telerounding system, 84% of patients agreed that they would feel comfortable with telerounding daily if they were hospitalized again and 81% of patients would prefer telerounding communication with their doctor than be directly seen by another doctor. Tablet telerounding using videoconferencing can be a strong supplementing tool in doctor-patient communication. It is convenient for the physician and increases the patient's hospital stay satisfaction. Copyright © 2012 Elsevier Inc. All rights reserved.

  20. NMR imaging of density distributions in tablets.

    PubMed

    Djemai, A; Sinka, I C

    2006-08-17

    This paper describes the use of (1)H nuclear magnetic resonance (NMR) for 3D mapping of the relative density distribution in pharmaceutical tablets manufactured under controlled conditions. The tablets are impregnated with a compatible liquid. The technique involves imaging of the presence of liquid which occupies the open pore space. The method does not require special calibration as the signal is directly proportional to the porosity for the imaging conditions used. The NMR imaging method is validated using uniform density flat faced tablets and also by direct comparison with X-ray computed tomography. The results illustrate (1) the effect of die wall friction on density distribution by compressing round, curved faced tablets using clean and pre-lubricated tooling, (2) the evolution of density distribution during compaction for both clean and pre-lubricated die wall conditions, by imaging tablets compressed to different compaction forces, and (3) the effect of tablet image on density distribution by compressing two complex shape tablets in identical dies to the same average density using punches with different geometries.

  1. Principles of Tablet Computing for Educators

    ERIC Educational Resources Information Center

    Katzan, Harry, Jr.

    2015-01-01

    In the study of modern technology for the 21st century, one of the most popular subjects is tablet computing. Tablet computers are now used in business, government, education, and the personal lives of practically everyone--at least, it seems that way. As of October 2013, Apple has sold 170 million iPads. The success of tablets is enormous and has…

  2. Mathematics Instruction and the Tablet PC

    ERIC Educational Resources Information Center

    Fister, K. Renee; McCarthy, Maeve L.

    2008-01-01

    The use of tablet PCs in teaching is a relatively new phenomenon. A cross between a notebook computer and a personal digital assistant (PDA), the tablet PC has all of the features of a notebook with the additional capability that the screen can also be used for input. Tablet PCs are usually equipped with a stylus that allows the user to write on…

  3. Using Tablet on Education

    ERIC Educational Resources Information Center

    Algoufi, Rateeba

    2016-01-01

    Technological advancements in digital devices have made educational methodology to adopt new strategies and procedures to suit the Mobile learning era. Mobile devices such as tablets are growing to be the focus of research studies and educational use around the globe in the present day. With the influence of handy computing tablets in the hands of…

  4. 21 CFR 520.82a - Aminopropazine fumarate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Aminopropazine fumarate tablets. 520.82a Section 520.82a Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Aminopropazine fumarate tablets. (a) Specifications. The drug is in tablet form. Each tablet contains...

  5. Evaluation of tableting and tablet properties of Kollidon SR: the influence of moisture and mixtures with theophylline monohydrate.

    PubMed

    Hauschild, Karsten; Picker-Freyer, Katharina M

    2006-02-01

    The aim of the study was firstly to investigate the influence of moisture on the tableting and tablet properties of Kollidon SR and secondly to investigate the influence of theophylline monohydrate on the tableting behavior and tablet properties produced from binary mixtures with Kollidon SR. In comparison to Kollidon SR, microcrystalline cellulose (MCC) was used. The glass transition temperature (Tg) of the powder over the whole range of RH (0-90%), and in addition, the Tg of tablets of Kollidon SR were measured. Densities and flowability of the powders were analyzed. The tablets were produced at five different maximum relative densities (rho(rel), max) on an instrumented eccentric tableting machine. They were produced at three different relative humidities (RH), 30%, 45%, and 60% RH for the pure substances and binary mixtures with different ratios of drug and excipient were tableted at 45% RH. The tableting properties were analyzed by 3D modeling, force-displacement profiles, and compactibility plots. First, the Tg of the powder decreased with increasing RH and the Tg of the tablet was 4-8 K lower than the powder. The predominant deformation of Kollidon SR is plastic deformation and Kollidon SR showed a higher compactibility than MCC. The parameters of the 3D model showed an extreme change between 45 and 60% RH, and at higher RH more and more particles deformed elastically. This was confirmed by analysis of force-displacement profiles. At 60% RH, the radial tensile strength of the Kollidon SR tablets was half of the radial tensile strength at 45% RH. The reason is a higher relative energy of plastic deformation than for MCC. This results in a better utilization of the energy to deform the powder into a tablet and the exceeding of the glass transition temperature at higher RH. In conclusion, at 60% RH at the same rho(rel, max), tableting and tablet properties of Kollidon SR are extremely changed since plasticity is significantly higher. In the second part of the

  6. Tablet-Aided BehavioraL intervention EffecT on Self-management skills (TABLETS) for Diabetes.

    PubMed

    Lynch, Cheryl P; Williams, Joni S; J Ruggiero, Kenneth; G Knapp, Rebecca; Egede, Leonard E

    2016-03-22

    Multiple randomized controlled trials (RCTs) show that behavioral lifestyle interventions are effective in improving diabetes management and that comprehensive risk factor management improves cardiovascular disease (CVD) outcomes. The role of technology has been gaining strong support as evidence builds of its potential to improve diabetes management; however, evaluation of its impact in minority populations is limited. This study intends to provide early evidence of a theory-driven intervention, Tablet-Aided BehavioraL intervention EffecT on Self-management skills (TABLETS), using real-time videoconferencing for education and skills training. We examine the potential for TABLETS to improve health risk behaviors and reduce CVD risk outcomes among a low-income African American (AA) population with poorly controlled type 2 diabetes. The study is a two-arm, pilot controlled trial that randomizes 30 participants to the TABLETS intervention and 30 participants to a usual care group. Blinded outcome assessments will be completed at baseline, 2.5 months (immediate post-intervention), and 6.5 months (follow-up). The TABLETS intervention consists of culturally tailored telephone-delivered diabetes education and skills training delivered via videoconferencing on tablet devices, with two booster sessions delivered via tablet-based videoconferencing at 3 months and 5 months to stimulate ongoing use of the tablet device with access to intervention materials via videoconferencing slides and a manual of supplementary materials. The primary outcomes are physical activity, diet, medication adherence, and self-monitoring behavior, whereas the secondary outcomes are HbA1c, low-density lipoprotein cholesterol (LDL-C), BP, CVD risk, and quality of life. This study provides a unique opportunity to assess the feasibility and efficacy of a theory-driven, tablet-aided behavioral intervention that utilizes real-time videoconferencing technology for education and skills training on self

  7. Drug loss while crushing tablets: Comparison of 24 tablet crushing devices

    PubMed Central

    Thong, Min Yew; Manrique, Yady J.

    2018-01-01

    This study investigated 24 tablet crushing devices for drug loss using different methods to recover the crushed tablet. 24 devices were compared: 3 with disposable cups, 6 with disposable bags, 12 without separate vessels and 3 types of mortar and pestle. One paracetamol tablet was crushed and recovered by tapping the powder out. Where appropriate, depending on crusher size and manufacturer instructions, the powder was also recovered by mixing with water or food. Paracetamol recovery (quantity that can be delivered to a patient) and leftover (quantity remaining in the device) were measured using a validated UV method and the entire experiment was replicated 3 times. Drug recovery ranged from 86.7–98.1% when the crushed tablet was tapped out of the crushers (average loss 5.8%). Significant losses were measured for 18 crushers, particularly manually operated hand-twist crushers with a serrated crushing surface, and some devices with disposable bags or cups. Rinsing the crushed powder with water once resulted in an average of 24.2% drug loss, and this was reduced to 4.2% after a second rinse. If crushing is unavoidable, maximizing medication delivery to the patient is essential. Rinsing twice resulted in similar paracetamol recovery to tapping the powder out; however only water rinses have the potential for direct consumption by the patient, minimizing drug loss across the entire crushing and transfer process. PMID:29494695

  8. 21 CFR 520.1193 - Ivermectin tablets and chewables.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ivermectin tablets and chewables. 520.1193 Section... tablets and chewables. (a) Specifications. (1) Each tablet or chewable contains 68, 136, or 272 micrograms... tablets or chewables described in paragraph (a)(1) as in paragraph (d)(1) and chewables described in...

  9. [Preparation of coated tablets of glycyrrhetic acid-HP-beta-cyclodextrin tablets for colon-specific release].

    PubMed

    Cui, Qi-Hua; Cui, Jing-Hao; Zhang, Jin-Jin

    2008-10-01

    To prepare coated tablets of glycyrrhetinic acid and hydroxypropyl-beta-cyclodextrin (GTA-HP-beta-CYD) inclusion complex tablets for colon-specific release. In order to improve the solubility of GTA, the GTA-HP-beta-CYD inclusion complex was prepared by ultrasonic-lyophilization technique and its formation were characterized by X-ray powder diffraction profiles and infrared spectrometry. The effects of inclusion condition on the inclusion efficiency and stability coefficient of inclusion complex were investigated, respectively. After prepared GTA-HP-beta-CYD tablets by powder direct compression, the pH dependant polymer Eudragit III and/or mixed with Eudragit II were used for further coating materials in fluid-bed coater. The influences of coating weight on the GTA release in different pH conditions were evaluated to establish the method for prepering colon specific delivery tablets with pulsed release properties. The formation of inclusion complexes were proved by X-ray powder diffraction profile and phase solubility curve. The effect of pH value of solvent was played critical role on the preparation of GTA- HP-beta-CYD inclusion complex. And the inclusion efficiency of GTA was 9. 3% and the solubility was increased to 54. 6 times at optimized method. The Eudragit III coated GTA- HP-beta-CYD tablets with coating weight 10% and 16% were showed pH dependant colon specific release profiles with slow release rate. The release profile of tablets coated with the mixture of Eudragit II and Eudragit III (1:2) were indicated typical pH dependant colon specific and pulsed release properties while the coating weight was 17%. The preliminary method for preparation of colon specific release tablets containing glycyrrhetinic acid with improved solubility was established for further in vivo therapeutic experiment.

  10. Microtomographic studies of subdivision of modified-release tablets.

    PubMed

    Wilczyński, Sławomir; Koprowski, Robert; Duda, Piotr; Banyś, Anna; Błońska-Fajfrowska, Barbara

    2016-09-25

    The uniformity of dosage units within a certain batch is ensured when each unit contains the active pharmaceutical ingredient (API) within a narrow range around the label claim. For tablets containing a score-line authorised for dose reductions, the European Pharmacopoeia (Ph. Eur.) considers that the uniformity of the tablet parts may be based on weight measurements regardless of the tablet type (immediate or modified release). This is because it is up to the regulatory authorities first to assess whether the tablet may contain a score-line for such use. X-ray microtomography was applied to assess the symmetry of 36 modified release tablets, containing 300mg of theophylline. The sum of the volume and surface area of the pellets in the subdivided tablets were compared. Simulations were carried out to identify the optimal amount of pellets in the tablet mass. The maximum difference in the API content between two subdivided halves was 165.18mg vs 133.83mg. If the amount of pellets in the tablet mass would drop below 13% on the basis of the pellet surface area, then the Ph. Eur. requirements would be exceeded. The amount of pellets in the tablet halves resulting in the greatest variability in API content was 38%. The results of this study indicate that the pellets were not distributed uniformly in the tablet mass. Thus, the uniformity of the dose in both halves of a tablet containing pellets cannot be based on the weight measurements i.e. it is necessary to develop further standards for tablet subdivision. Microtomographic methods are a very interesting alternative to expensive and time-consuming pharmacokinetic studies. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. 21 CFR 520.2150b - Stanozolol chewable tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stanozolol chewable tablets. 520.2150b Section 520... chewable tablets. (a) Specifications. Each chewable tablet contains 2 milligrams of stanozolol. (b) Sponsor... treatment in dogs. (2) Administered orally to small breeds of dogs, 1/2 to 1 tablet twice daily for several...

  12. 21 CFR 529.400 - Chlorhexidine tablets and suspension.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Chlorhexidine tablets and suspension. 529.400... Chlorhexidine tablets and suspension. (a) Specification. Each tablet and each 28-milliliter syringe of.... 000856 in § 510.600(c) of this chapter. (c) Conditions of use—(1) Amount. Place 1 or 2 tablets deep in...

  13. Terahertz Technology: A Boon to Tablet Analysis

    PubMed Central

    Wagh, M. P.; Sonawane, Y. H.; Joshi, O. U.

    2009-01-01

    The terahertz gap has a frequency ranges from ∼0.3 THz to ∼10 THz in the electromagnetic spectrum which is in between microwave and infrared. The terahertz radiations are invisible to naked eye. In comparison with x-ray they are intrinsically safe, non-destructive and non-invasive. Terahertz spectroscopy enables 3D imaging of structures and materials, and the measurement of the unique spectral fingerprints of chemical and physical forms. Terahertz radiations are produced by a dendrimer based high power terahertz source and spectroscopy technologies. It resolves many of the questions left unanswered by complementary techniques, such as optical imaging, Raman and infrared spectra. In the pharmaceutical industries it enables nondestructive, internal, chemical analysis of tablets, capsules, and other dosage forms. Tablet coatings are a major factor in drug bioavailability. Therefore tablet coatings integrity and uniformity are of crucial importance to quality. Terahertz imaging gives an unparalleled certainty about the integrity of tablet coatings and the matrix performance of tablet cores. This article demonstrates the potential of terahertz pulse imaging for the analysis of tablet coating thickness by illustrating the technique on tablets. PMID:20490288

  14. Gastric emptying of enteric-coated tablets

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Park, H.M.; Chernish, S.M.; Rosenek, B.D.

    1984-03-01

    To evaluate the gastric emptying time of pharmaceutical dosage forms in a clinical setting, a relatively simple dual-radionuclide technique was developed. Placebo tablets of six different combinations of shape and size were labeled with indium-111 DTPA and enteric coated. Six volunteers participated in a single-blind and crossover study. Tablets were given in the morning of a fasting stomach with 6 oz of water containing /sup 99m/Tc pertechnetate and continuously observed with a gamma camera. A scintigraph was obtained each minute. The results suggested that the size, shape, or volume of the tablet used in this study had no significant effectmore » in the rate of gastric emptying. The tablets emptied erratically and unpredictably, depending upon their time of arrival in the stomach in relation to the occurrence of interdigestive myoelectric contractions. The method described is a relatively simple and accurate technique to allow one to follow the gastric emptying of tablets.« less

  15. 21 CFR 520.863 - Ethylisobutrazine hydrochloride tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ethylisobutrazine hydrochloride tablets. 520.863 Section 520.863 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Ethylisobutrazine hydrochloride tablets. (a) Specifications. Each tablet contains either 10 milligrams or 50...

  16. 21 CFR 520.2582 - Triflupromazine hydrochloride tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Triflupromazine hydrochloride tablets. 520.2582 Section 520.2582 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Triflupromazine hydrochloride tablets. (a) Specifications. Each tablet contains either 10 milligrams or 25...

  17. [Bioequivalence of pyridostigmine bromide dispersible tablets in rabbits].

    PubMed

    Wang, Hong; Wang, Hong; Tan, Qun-you; Zhang, Li; Cheng, Xun-guan; Zhang, Jing-qing

    2011-10-01

    To compare the pharmacokinetic parameters of pyridostigmine bromide dispersible tablets and common tablets in rabbits. Twelve rabbits were given an oral dose (60 mg) of pyridostigmine bromide dispersible tablets or common tablets in a randomized crossover study. The plasma concentration of pyridostigmine bromide was determined by reversed-phase ion pair chromatography. The pharmacokinetic parameters were calculated using DAS2.1.1 software. The pharmacokinetic parameters showed no significant differences in rabbit plasma between pyridostigmine bromide dispersible tablets and common tablets. The two tablets had a C(max) of 1.83∓0.08 mg·L(-1) and 1.68∓0.03 mg·L(-1), tmax of 2.33∓0.41 h and 2.58∓0.20 h, AUC(0-24) of 15.50∓0.62 mg·h·L(-1) and 15.14∓0.30 mg·h·L(-1), AUC(0-∞) of 15.82∓0.70 mg·h·L(-1) and 15.57∓0.32 mg·h·L(-1), respectively. The relative bioavailability F(0-24) was 102.38% and F(0-∞) was 101.61% for the dispersible tablets. The two tablets are bioequivalent in rabbits.

  18. 21 CFR 520.2158b - Dihydrostreptomycin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Dihydrostreptomycin tablets. 520.2158b Section 520.2158b Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Dihydrostreptomycin tablets. (a) Specifications. Each tablet contains 37.5 milligrams dihydrostreptomycin (as the...

  19. 21 CFR 520.2362 - Thenium closylate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Thenium closylate tablets. 520.2362 Section 520... tablets. (a) Chemical name. (N,N-Dimethyl-N-2-phenoxyethyl-N-2′-thenylammo-nium)-p-chlorobenzene-sulfonate. (b) Specifications. Thenium closylate tablets contain thenium closylate equivalent to 500 milligrams...

  20. 21 CFR 520.246 - Butorphanol tartrate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Butorphanol tartrate tablets. 520.246 Section 520.246 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... tartrate tablets. (a) Specifications. Each tablet contains 1, 5, or 10 milligrams of butorphanol base...

  1. 21 CFR 520.1331 - Meclofenamic acid tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Meclofenamic acid tablets. 520.1331 Section 520.1331 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... tablets. (a) Specifications. Each tablet contains either 10 or 20 milligrams of meclofenamic acid. (b...

  2. Epinephrine Use in Clinical Trials of Sublingual Immunotherapy Tablets.

    PubMed

    Nolte, Hendrik; Casale, Thomas B; Lockey, Richard F; Fogh, Bodil Svanholm; Kaur, Amarjot; Lu, Susan; Nelson, Harold S

    Allergy immunotherapy can result in systemic allergic reactions and even life-threatening anaphylaxis requiring epinephrine administration. The objective of this study was to describe epinephrine use in the clinical trial development programs of 3 rapidly dissolving sublingual immunotherapy tablets (SLIT-tablets; Merck & Co., Inc., Kenilworth, NJ/ALK, Hørsholm, Denmark/Torii Pharmaceutical Co., Ltd., Tokyo, Japan). Data on epinephrine use were collected from 13 timothy grass SLIT-tablet trials (MK-7243; ≤2800 bioequivalent allergen units/75,000 SQ-T dose, n = 2497; placebo, n = 2139), 5 short ragweed SLIT-tablet trials (MK-3641; ≤12 Amb a 1-U, n = 1725; placebo, n = 770), and 11 house dust mite (HDM) SLIT-tablet trials (MK-8237; ≤12 SQ-HDM; n = 3930; placebo, n = 2246). In grass SLIT-tablet trials, epinephrine was used 13 times (grass SLIT-tablet, n = 10; placebo, n = 3). Eight administrations were for grass SLIT-tablet-related adverse events (AEs): 4 for systemic allergic reactions and 4 for local mouth and/or throat swelling. In ragweed SLIT-tablet trials, epinephrine was used 9 times in 8 subjects (ragweed SLIT-tablet, n = 7; placebo, n = 1 [2 administrations for protracted anaphylaxis]). Four administrations were for ragweed SLIT-tablet-related AEs: 1 for systemic allergic reaction and 3 for local mouth and/or pharynx/throat swelling. In HDM SLIT-tablet trials, epinephrine was administered 13 times (HDM SLIT-tablet, n = 8; placebo, n = 5). Four administrations were for HDM SLIT-tablet-related AEs: 1 for systemic allergic reaction and 3 for local events. Of the 16 epinephrine administrations for events related to SLIT-tablet treatment, 11 occurred within the first week of treatment (7 administrations on day 1) and 5 were subject self-administered. Epinephrine administrations in response to SLIT-tablet-related reactions in clinical trials are uncommon, typically occur within the first week of treatment, and are rarely self-administered. All

  3. 21 CFR 520.1157 - Iodinated casein tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Iodinated casein tablets. 520.1157 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1157 Iodinated casein tablets. (a) Specifications. Each 1-gram tablet contains 25 milligrams of iodinated casein. (b) Sponsor...

  4. 21 CFR 520.1157 - Iodinated casein tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Iodinated casein tablets. 520.1157 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1157 Iodinated casein tablets. (a) Specifications. Each 1-gram tablet contains 25 milligrams of iodinated casein. (b) Sponsor...

  5. 21 CFR 520.1341 - Megestrol acetate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Megestrol acetate tablets. 520.1341 Section 520.1341 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... tablets. (a) Specifications. Each tablet contains 5 or 20 milligrams of megestrol acetate. (b) Sponsor. No...

  6. 21 CFR 520.784 - Doxylamine succinate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Doxylamine succinate tablets. 520.784 Section 520.784 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... succinate tablets. (a) Specifications. The drug is in tablet form and contains doxylamine succinate as the...

  7. 21 CFR 520.2042 - Pyrantel pamoate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Pyrantel pamoate tablets. 520.2042 Section 520.2042 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... tablets. (a) Specifications. Each tablet contains pyrantel pamoate equivalent to 22.7, 45.4, or 113.5...

  8. 21 CFR 520.1331 - Meclofenamic acid tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Meclofenamic acid tablets. 520.1331 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1331 Meclofenamic acid tablets. (a) Specifications. Each tablet contains either 10 or 20 milligrams of meclofenamic acid. (b...

  9. 21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

  10. 21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

  11. 21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

  12. 21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

  13. 21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

  14. Reduction of tablet weight variability by optimizing paddle speed in the forced feeder of a high-speed rotary tablet press.

    PubMed

    Peeters, Elisabeth; De Beer, Thomas; Vervaet, Chris; Remon, Jean-Paul

    2015-04-01

    Tableting is a complex process due to the large number of process parameters that can be varied. Knowledge and understanding of the influence of these parameters on the final product quality is of great importance for the industry, allowing economic efficiency and parametric release. The aim of this study was to investigate the influence of paddle speeds and fill depth at different tableting speeds on the weight and weight variability of tablets. Two excipients possessing different flow behavior, microcrystalline cellulose (MCC) and dibasic calcium phosphate dihydrate (DCP), were selected as model powders. Tablets were manufactured via a high-speed rotary tablet press using design of experiments (DoE). During each experiment also the volume of powder in the forced feeder was measured. Analysis of the DoE revealed that paddle speeds are of minor importance for tablet weight but significantly affect volume of powder inside the feeder in case of powders with excellent flowability (DCP). The opposite effect of paddle speed was observed for fairly flowing powders (MCC). Tableting speed played a role in weight and weight variability, whereas changing fill depth exclusively influenced tablet weight. The DoE approach allowed predicting the optimum combination of process parameters leading to minimum tablet weight variability. Monte Carlo simulations allowed assessing the probability to exceed the acceptable response limits if factor settings were varied around their optimum. This multi-dimensional combination and interaction of input variables leading to response criteria with acceptable probability reflected the design space.

  15. Relationship between Age and the Ability to Break Scored Tablets

    PubMed Central

    Notenboom, Kim; Vromans, Herman; Schipper, Maarten; Leufkens, Hubert G. M.; Bouvy, Marcel L.

    2016-01-01

    Background: Practical problems with the use of medicines, such as difficulties with breaking tablets, are an often overlooked cause for non-adherence. Tablets frequently break in uneven parts and loss of product can occur due to crumbling and powdering. Health characteristics, such as the presence of peripheral neuropathy, decreased grip strength and manual dexterity, can affect a patient's ability to break tablets. As these impairments are associated with aging and age-related diseases, such as Parkinson's disease and arthritis, difficulties with breaking tablets could be more prevalent among older adults. The objective of this study was to investigate the relationship between age and the ability to break scored tablets. Methods: A comparative study design was chosen. Thirty-six older adults and 36 young adults were systematically observed with breaking scored tablets. Twelve different tablets were included. All participants were asked to break each tablet by three techniques: in between the fingers with the use of nails, in between the fingers without the use of nails and pushing the tablet downward with one finger on a solid surface. It was established whether a tablet was broken or not, and if broken, whether the tablet was broken accurately or not. Results: The older adults experienced more difficulties to break tablets compared to the young adults. On average, the older persons broke 38.1% of the tablets, of which 71.0% was broken accurately. The young adults broke 78.2% of the tablets, of which 77.4% was broken accurately. Further analysis by mixed effects logistic regression revealed that age was associated with the ability to break tablets, but not with the accuracy of breaking. Conclusions: Breaking scored tablets by hand is less successful in an elderly population compared to a group of young adults. Health care providers should be aware that tablet breaking is not appropriate for all patients and for all drugs. In case tablet breaking is unavoidable, a

  16. [Modern polymers in matrix tablets technology].

    PubMed

    Zimmer, Łukasz; Kasperek, Regina; Poleszak, Ewa

    2014-01-01

    Matrix tablets are the most popular method of oral drug administration, and polymeric materials have been used broadly in matrix formulations to modify and modulate drug release rate. The main goal of the system is to extend drug release profiles to maintain a constant in vivo plasma drug concentration and a consistent pharmacological effect. Polymeric matrix tablets offer a great potential as oral controlled drug delivery systems. Cellulose derivatives, like hydroxypropyl methylcellulose (HPMC) are often used as matrix formers. However, also other types of polymers can be used for this purpose including: Kollidon SR, acrylic acid polymers such as Eudragits and Carbopols. Nevertheless, polymers of natural origin like: carragens, chitosan and alginates widely used in the food and cosmetics industry are now coming to the fore of pharmaceutical research and are used in matrix tablets technology. Modern polymers allow to obtain matrix tablets by 3D printing, which enables to develop new formulation types. In this paper, the polymers used in matrix tablets technology and examples of their applications were described.

  17. Tablet splitting: is it worthwhile? Analysis of drug content and weight uniformity for half tablets of 16 commonly used medications in the outpatient setting.

    PubMed

    Helmy, Sally A

    2015-01-01

    Tablet splitting is a well-established medical practice in clinical settings for multiple reasons, including cost savings and ease of swallowing. However, it does not necessarily result in weight-uniform half tablets. To (a) investigate the effect of tablet characteristics on weight and content uniformity of half tablets, resulting from splitting 16 commonly used medications in the outpatient setting and (b) provide recommendations for safe tablet-splitting prescribing practices. Ten random tablets from each of the selected medications were weighed and split by 5 volunteers (2 men and 3 women aged 25-44 years) using a knife. The selected medications were mirtazapine 30 mg, bromazepam 3 mg, oxcarbazepin 150 mg, sertraline 50 mg, carvedilol 25 mg, bisoprolol fumarate 10 mg, losartan 50 mg, digoxin 0.25 mg, amiodarone HCl 200 mg, metformin HCl 1,000 mg, glimepiride 4 mg, montelukast 10 mg, ibuprofen 600 mg, celecoxib 200 mg, meloxicam 15 mg, and sildenafil citrate 50 mg. The resulting half tablets were evaluated for weight and drug content uniformity in accordance with proxy United States Pharmacopeia (USP) specification (95%-105% for digoxin and 90%-110% for the other 15 drugs). Weight and drug content uniformity were assessed by comparing weight or drug content of the half tablets with one-half of the mean weight or drug content for all whole tablets in the sample. The percentages by which the weight and drug content of each whole tablet or half tablet differed from sample mean values were calculated. Other relevant physical characteristics of the 16 products were measured. A total of 52 of 320 half tablets (16.2%) and 48 of 320 half tablets (15.0%) fell outside of the proxy USP specification for weight and drug content, respectively. Bromazepam, carvedilol, bisoprolol, losartan, digoxin, and meloxicam half tablets failed the weight and content uniformity test; however, the half tablets for the rest of the medications passed the test. Mean percent weight loss after

  18. Continuous manufacturing of tablets with PROMIS-line - Introduction and case studies from continuous feeding, blending and tableting.

    PubMed

    Simonaho, Simo-Pekka; Ketolainen, Jarkko; Ervasti, Tuomas; Toiviainen, Maunu; Korhonen, Ossi

    2016-07-30

    Drug manufacturing technology is in the midst of modernization and continuous manufacturing of drug products is especially the focus of great interest. The adoption of new manufacturing approaches requires extensive cooperation between industry, regulatory bodies, academics and equipment manufacturers. In this paper we introduce PROMIS-line which is a continuous tableting line built at the University of Eastern Finland, School of Pharmacy, PROMIS-centre. PROMIS-line is modular and tablets can be produced via dry granulation or direct compression. In three case studies, continuous feeding, blending and tablet performance is studied to illustrate some basic features of PROMIS-line. In conclusion, the PROMIS-line is an excellent tool for studying the fundamentals of continuous manufacturing of tablets. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Scaffolding Equals Success in Teaching Tablet PCs

    ERIC Educational Resources Information Center

    Dickerson, Jeremy; Williams, Scott; Browning, J. B.

    2009-01-01

    After many years of using the mouse and keyboard as the primary means of computer input, people are seeing a strong surge into a new generation of input technologies such as tablet PCs. As more professionals adopt tablet PCs for use in the workplace, there is a subsequent increased demand for tablet PC instruction in the classroom. Examples of…

  20. 21 CFR 520.2150a - Stanozolol tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... chapter. (c) Conditions of use. (1) Used as an anabolic steroid treatment in dogs and cats. (2) Administered orally to cats and small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. The tablets may be crushed and administered...

  1. 21 CFR 520.2150a - Stanozolol tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... chapter. (c) Conditions of use. (1) Used as an anabolic steroid treatment in dogs and cats. (2) Administered orally to cats and small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. The tablets may be crushed and administered...

  2. 21 CFR 520.2150a - Stanozolol tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... chapter. (c) Conditions of use. (1) Used as an anabolic steroid treatment in dogs and cats. (2) Administered orally to cats and small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. The tablets may be crushed and administered...

  3. 21 CFR 520.2150a - Stanozolol tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... chapter. (c) Conditions of use. (1) Used as an anabolic steroid treatment in dogs and cats. (2) Administered orally to cats and small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. The tablets may be crushed and administered...

  4. 21 CFR 520.903e - Febantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Febantel tablets. 520.903e Section 520.903e Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.903e Febantel tablets. (a) Specifications. Each scored tablet contains 27.2 milligrams of febantel for use in dogs, puppies, cats, and...

  5. 21 CFR 520.2150a - Stanozolol tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Stanozolol tablets. 520.2150a Section 520.2150a... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.2150a Stanozolol tablets. (a) Specifications. Each tablet contains 2 milligrams of stanozolol. (b) Sponsor. No. 000009 in § 510.600(c) of this...

  6. 21 CFR 520.1872 - Praziquantel, pyrantel pamoate, and febantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... tablets. 520.1872 Section 520.1872 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... § 520.1872 Praziquantel, pyrantel pamoate, and febantel tablets. (a) Specifications. Each tablet or chewable tablet contains either: (1) Tablet No. 1: 22.7 milligrams praziquantel, 22.7 milligrams pyrantel...

  7. Orodispersible tablets containing taste-masked solid lipid pellets with metformin hydrochloride: Influence of process parameters on tablet properties.

    PubMed

    Petrovick, Gustavo Freire; Kleinebudde, Peter; Breitkreutz, Jörg

    2018-01-01

    Compaction of multiparticulates into tablets, particularly into orodispersible tablets (ODTs), is challenging. The compression of pellets, made by solid lipid extrusion/spheronization processes, presents peculiar difficulties since solid lipids usually soften or melt at relatively low temperature ranges and due to applied mechanical forces. Until now, there are no reports in literature about the development of ODTs based on solid lipid pellets. To investigate the feasibility of producing such tablets, a design of experiment (DoE) approach was performed to elucidate the influence of compression force and amount of two co-processed excipients (Ludiflash ® and Parteck ® ODT) on properties of the tablets (friability, tensile strength, and disintegration time). ODTs (15 mm, flat-faced) with solid lipid pellets (250-1000 µm in diameter) containing 500 mg of metformin HCl, presenting immediate drug release profile and taste-masked properties, were targeted. During compression, a strong lamination of the tablets containing Parteck ® ODT was observed. This phenomenon was prominently observed when high compression forces (≥5 kN) and high excipient amounts (≥40%; w/w) were used. On the other hand, the DoE focused on tablets with Ludiflash ® showed better results regarding the production of ODTs. A positive influence of the compression force on the tensile strength and disintegration time of the tablets, regarding specifications of the Ph. Eur., was observed. The increase in the amount of this excipient resulted in fast disintegrating tablets, however, a negative influence on the tensile strength was noticed. After optimization of the parameters and formulation, based on the DoE results and considering the Ph. Eur. specifications for tablets, ODTs based on lipid pellets containing metformin HCl presenting immediate release profile (85% drug release in less than 30 min) and taste-masked properties (determined by an electronic tongue) were successfully

  8. Evaluation of the tablets' surface flow velocities in pan coaters.

    PubMed

    Dreu, Rok; Toschkoff, Gregor; Funke, Adrian; Altmeyer, Andreas; Knop, Klaus; Khinast, Johannes; Kleinebudde, Peter

    2016-09-01

    The tablet pan coating process involves various types of transverse tablet bed motions, ranging from rolling to cascading. To preserve satisfactory results in terms of coating quality after scale-up, understanding the dynamics of pan coating process should be achieved. The aim of this study was to establish a methodology of estimating translational surface velocities of the tablets in a pan coater and to assess their dependence on the drum's filling degree, the pan speed, the presence of baffles and the selected tablet properties in a dry bed system and during coating while varying the drum's filling degree and the pan speed. Experiments were conducted on the laboratory scale and on the pilot scale in side-vented pan coaters. Surface movement of biconvex two-layer tablets was assessed before, during and after the process of active coating. In order to determine the tablets' surface flow velocities, a high-speed video of the tablet surface flow was recorded via a borescope inserted into the coating drum and analysed via a cross-correlation algorithm. The obtained tablet velocity data were arranged in a linear fashion as a function of the coating drum's radius and frequency. Velocity data obtained during coating were close to those of dry tablets after coating. The filling degree had little influence on the tablet velocity profile in a coating drum with baffles but clearly affected it in a coating drum without baffles. In most but not all cases, tablets with a lower static angle of repose had tablet velocity profiles with lower slopes than tablets with higher inter-tablet friction. This particular tablet velocity response can be explained by case specific values of tablet bed's dynamic angle of repose. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Challenges in detecting magnesium stearate distribution in tablets.

    PubMed

    Lakio, Satu; Vajna, Balázs; Farkas, István; Salokangas, Henri; Marosi, György; Yliruusi, Jouko

    2013-03-01

    Magnesium stearate (MS) is the most commonly used lubricant in pharmaceutical industry. During blending, MS particles form a thin layer on the surfaces of the excipient and drug particles prohibiting the bonding from forming between the particles. This hydrophobic layer decreases the tensile strength of tablets and prevents water from penetrating into the tablet restraining the disintegration and dissolution of the tablets. Although overlubrication of the powder mass during MS blending is a well-known problem, the lubricant distribution in tablets has traditionally been challenging to measure. There is currently no adequate analytical method to investigate this phenomenon. In this study, the distribution of MS in microcrystalline cellulose (MCC) tablets was investigated using three different blending scales. The crushing strength of the tablets was used as a secondary response, as its decrease is known to result from the overlubrication. In addition, coating of the MCC particles by MS in intact tablets was detected using Raman microscopic mapping. MS blending was more efficient in larger scales. Raman imaging was successfully applied to characterize MS distribution in MCC tablets despite low concentration of MS. The Raman method can provide highly valuable visual information about the proceeding of the MS blending process. However, the measuring set-up has to be carefully planned to establish reliable and reproducible results.

  10. Systematic evaluation of common lubricants for optimal use in tablet formulation.

    PubMed

    Paul, Shubhajit; Sun, Changquan Calvin

    2018-05-30

    As an essential formulation component for large-scale tablet manufacturing, the lubricant preserves tooling by reducing die-wall friction. Unfortunately, lubrication also often results in adverse effects on tablet characteristics, such as prolonged disintegration, slowed dissolution, and reduced mechanical strength. Therefore, the choice of lubricant and its optimal concentration in a tablet formulation is a critical decision in tablet formulation development to attain low die-wall friction while minimizing negative impact on other tablet properties. Three commercially available tablet lubricants, i.e., magnesium stearate, sodium stearyl fumerate, and stearic acid, were systematically investigated in both plastic and brittle matrices to elucidate their effects on reducing die-wall friction, tablet strength, tablet hardness, tablet friability, and tablet disintegration kinetics. Clear understanding of the lubrication efficiency of commonly used lubricants as well as their impact on tablet characteristics would help future tablet formulation efforts. Copyright © 2018 Elsevier B.V. All rights reserved.

  11. 21 CFR 520.1199 - Ivermectin, pyrantel, and praziquantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ivermectin, pyrantel, and praziquantel tablets... Ivermectin, pyrantel, and praziquantel tablets. (a) Specifications. Each chewable tablet contains: (1) 34...) Amount. Administer monthly according to body weight as follows: (i) 6 to 12 lb: one tablet as described...

  12. 21 CFR 520.1200 - Ivermectin, fenbendazole, and praziquantel tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ivermectin, fenbendazole, and praziquantel tablets... Ivermectin, fenbendazole, and praziquantel tablets. (a) Specifications. Each chewable tablet contains either... § 510.600(c) of this chapter. (c) Conditions of use in dogs—(1) Amount. Administer tablets to provide 6...

  13. Continuous direct tablet compression: effects of impeller rotation rate, total feed rate and drug content on the tablet properties and drug release.

    PubMed

    Järvinen, Maiju A; Paaso, Janne; Paavola, Marko; Leiviskä, Kauko; Juuti, Mikko; Muzzio, Fernando; Järvinen, Kristiina

    2013-11-01

    Continuous processing is becoming popular in the pharmaceutical industry for its cost and quality advantages. This study evaluated the mechanical properties, uniformity of dosage units and drug release from the tablets prepared by continuous direct compression process. The tablet formulations consisted of acetaminophen (3-30% (w/w)) pre-blended with 0.25% (w/w) colloidal silicon dioxide, microcrystalline cellulose (69-96% (w/w)) and magnesium stearate (1% (w/w)). The continuous tableting line consisted of three loss-in-weight feeders and a convective continuous mixer and a rotary tablet press. The process continued for 8 min and steady state was reached within 5 min. The effects of acetaminophen content, impeller rotation rate (39-254 rpm) and total feed rate (15 and 20 kg/h) on tablet properties were examined. All the tablets complied with the friability requirements of European Pharmacopoeia and rapidly released acetaminophen. However, the relative standard deviation of acetaminophen content (10% (w/w)) increased with an increase in impeller rotation rate at a constant total feed rate (20 kg/h). A compression force of 12 kN tended to result in greater tablet hardness and subsequently a slower initial acetaminophen release from tablets when compared with those made with the compression force of about 8 kN. In conclusion, tablets could be successfully prepared by a continuous direct compression process and process conditions affected to some extent tablet properties.

  14. 21 CFR 520.2280 - Sulfamethizole and methenamine mandelate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfamethizole and methenamine mandelate tablets... Sulfamethizole and methenamine mandelate tablets. (a) Specifications. Each tablet contains 250 milligrams of... urethra and bladder. (2) It is administered at a dosage level of one tablet for each 20 pounds of body...

  15. 21 CFR 520.1446 - Milbemcyin oxime and lufenuron tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Milbemcyin oxime and lufenuron tablets. 520.1446... oxime and lufenuron tablets. (a) Specifications—(1) Tablets containing: 2.3 milligrams (mg) milbemycin... 230 mg lufenuron, or 23 mg milbemycin oxime and 460 mg lufenuron. (2) Flavored tablets containing: 2.3...

  16. Enalapril maleate orally disintegrating tablets: tableting and in vivo evaluation in hypertensive rats.

    PubMed

    Tawfeek, Hesham M; Faisal, Waleed; Soliman, Ghareb M

    2018-06-01

    The aim of this study was to develop orally disintegrating tablets (ODTs) for enalapril maleate (EnM) to facilitate its administration to the elderly or other patients having dysphagia. Compatibility between EnM and various excipients was studied using differential scanning calorimetry. ODTs of EnM were prepared by direct compression of EnM mixtures with various superdisintegrants. The tablets were evaluated for physical properties including drug content, hardness, friability, disintegration time, wetting time, and drug release. The antihypertensive effect of the optimum EnM ODTs was evaluated in vivo in hypertensive rats and compared with commercial EnM formulation. EnM ODTs had satisfactory results in terms of drug content and friability. Tablet wetting and disintegration were fast and dependent on the used superdisintegrant where croscarmellose showed the fastest wetting and disintegration time of ∼7 s. EnM release from the tablets was rapid where complete release was obtained in 10-15 min. Selected EnM ODTs rapidly and efficiently reduced the rat's blood pressure to its normal value within 1 h, compared with 4 h for EnM commercial formulation. These results confirm that EnM ODTs could find application in the management of hypertension in the elderly or other patients having dysphagia.

  17. Key Technical Aspects Influencing the Accuracy of Tablet Subdivision.

    PubMed

    Teixeira, Maíra T; Sá-Barreto, Lívia C L; Gratieri, Taís; Gelfuso, Guilherme M; Silva, Izabel C R; Cunha-Filho, Marcílio S S

    2017-05-01

    Tablet subdivision is a common practice used mainly for dose adjustment. The aim of this study was to investigate how the technical aspects of production as well as the method of tablets subdivision (employing a tablet splitter or a kitchen knife) influence the accuracy of this practice. Five drugs commonly used as subdivided tablets were selected. For each drug, the innovator drug product, a scored-generic and a non-scored generic were investigated totalizing fifteen drug products. Mechanical and physical tests, including image analysis, were performed. Additionally, comparisons were made between tablet subdivision method, score, shape, diluent composition and coating. Image analysis based on surface area was a useful tool as an alternative assay to evaluate the accuracy of tablet subdivision. The tablet splitter demonstrates an advantage relative to a knife as it showed better results in weight loss and friability tests. Oblong, coated and scored tablets had better results after subdivision than round, uncoated and non-scored tablets. The presence of elastic diluents such as starch and dibasic phosphate dehydrate conferred a more appropriate behaviour for the subdivision process than plastic materials such as microcrystalline cellulose and lactose. Finally, differences were observed between generics and their innovator products in all selected drugs with regard the quality control assays in divided tablet, which highlights the necessity of health regulations to consider subdivision performance at least in marketing authorization of generic products.

  18. Composition profiling of seized ecstasy tablets by Raman spectroscopy.

    PubMed

    Bell, S E; Burns, D T; Dennis, A C; Matchett, L J; Speers, J S

    2000-10-01

    Raman spectroscopy with far-red excitation has been investigated as a simple and rapid technique for composition profiling of seized ecstasy (MDMA, N-methyl-3,4-methylenedioxyamphetamine) tablets. The spectra obtained are rich in vibrational bands and allow the active drug and excipient used to bulk the tablets to be identified. Relative band heights can be used to determine drug/excipient ratios and the degree of hydration of the drug while the fact that 50 tablets per hour can be analysed allows large numbers of spectra to be recorded. The ability of Raman spectroscopy to distinguish between ecstasy tablets on the basis of their chemical composition is illustrated here by a sample set of 400 tablets taken from a large seizure of > 50,000 tablets that were found in eight large bags. The tablets are all similar in appearance and carry the same logo. Conventional analysis by GC-MS showed they contained MDMA. Initial Raman studies of samples from each of the eight bags showed that despite some tablet-to-tablet variation within each bag the contents could be classified on the basis of the excipients used. The tablets in five of the bags were sorbitol-based, two were cellulose-based and one bag contained tablets with a glucose excipient. More extensive analysis of 50 tablets from each of a representative series of sample bags have distribution profiles that showed the contents of each bag were approximately normally distributed about a mean value, rather than being mixtures of several discrete types. Two of the sorbitol-containing sample sets were indistinguishable while a third was similar but not identical to these, in that it contained the same excipient and MDMA with the same degree of hydration but had a slightly different MDMA/sorbitol ratio. The cellulose-based samples were badly manufactured and showed considerable tablet-to-tablet variation in their drug/excipient ratio while the glucose-based tablets had a tight distribution in their drug/excipient ratios

  19. 21 CFR 520.622c - Diethylcarbamazine citrate chewable tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Diethylcarbamazine citrate chewable tablets. 520... Diethylcarbamazine citrate chewable tablets. (a) Specifications. Each chewable tablet contains 30, 45, 60, 120, 150... tablets as in paragraph (c)(2)(i) of this section. (2) For 000069, use of 60, 120, or 180 milligram...

  20. [Production and assessing release of imipramine and magnesium from tablets].

    PubMed

    Kasperek, Regina; Zimmer, Łukasz; Szalast-Pietrzak, Agnieszka; Marzec, Zbigniew; Poleszak, Ewa

    2014-01-01

    In the pharmaceutical technology there is a trend to produce tablets composed of several medicinal substances to increase therapeutic effect and reduce the frequency of drug administration. In the literature there are reports concerning pharmacological studies in which a potentiation of the effects has been observed after a co-administration of antidepressant imipramine and magnesium. Currently, there is no formulation on the market comprising imipramine and magnesium, therefore, it was decided to produce uncoated tablets. In order to prepare the tablets by direct compression, it was necessary to select suitable excipients. The aim of the study was to elaborate the composition and to prepare the tablets with imipramine and magnesium, as well as to assess the quality of the tablets by physical characteristics and by the release study of the active substances. In order to prepare the tablets, compositions of different polymers and other excipients were added. The tablets were produced by direct compression method in a tablet press. Physical properties of the obtained tablets and the release of the active substances into an acidic medium in a paddle apparatus were tested. The contents of imipramine and magnesium were determined by different methods: spectrophotometrically and atomic absorption spectrometry, respectively. The composition of excipients necessary to produce tablets comprising imipramine and magnesium was established. All of prepared tablets were in compliance with the pharmacopoeial requirements. The release tests showed that above 80% of imipramine was released within 20-35 min and 80-76% of magnesium up to 45 min from the composed tablets and one-ingredient tablets, respectively. The compositions of excipients for tablets consisting of imipramine and magnesium were presented. The active substances were released within 45 min in the acidic medium, and the administration of these substances in the composed tablets did not affect pharmaceutical

  1. 21 CFR 520.82b - Aminopropazine fumarate, neomycin sulfate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Aminopropazine fumarate, neomycin sulfate tablets... Aminopropazine fumarate, neomycin sulfate tablets. (a) Specifications. The drug is in tablet form. Each tablet... administered at a dosage level of one to two tablets per 10 pounds of body weight twice daily for 3 days.1 (3...

  2. How do roll compaction/dry granulation affect the tableting behaviour of inorganic materials? Microhardness of ribbons and mercury porosimetry measurements of tablets.

    PubMed

    Freitag, Franziska; Reincke, Katrin; Runge, Jürgen; Grellmann, Wolfgang; Kleinebudde, Peter

    2004-07-01

    The effect of roll compaction/dry granulation on the ribbon and tablet properties produced using different magnesium carbonates was evaluated. The ribbon microhardness and the pore size distribution of tablets were used as evaluation factors. Increasing the specific compaction force resulted in higher microhardness for ribbons prepared with all four magnesium carbonates accompanied with decreased part of fine. Consequently, the corresponding produced tablets displayed a lower tensile strength. A possible correlation between the particle shape, surface area and the resulting pore structure of tablets produced with the four different types of magnesium carbonate was observed. The tensile strength of tablets prepared using granules was lower than tensile strength of tablets produced using starting materials. The partial loss of compactibility resulted in a demand of low loads during roll compaction. However, the impact of changes in the material properties during the roll compaction depended greatly on the type of magnesium carbonate, the specific compaction force and the tableting pressure applied.

  3. 21 CFR 520.581 - Dichlorophene tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...) Specifications. Each tablet contains 1 gram of dichlorophene. (b) Sponsor. See 023851 in § 510.600(c) of this.... Dogs—(1) Amount. Single dose of 1 tablet (1 gram of dichlorophene) for each 10 pounds of body weight...

  4. 21 CFR 520.581 - Dichlorophene tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...) Specifications. Each tablet contains 1 gram of dichlorophene. (b) Sponsor. See 023851 in § 510.600(c) of this.... Dogs—(1) Amount. Single dose of 1 tablet (1 gram of dichlorophene) for each 10 pounds of body weight...

  5. 21 CFR 520.581 - Dichlorophene tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...) Specifications. Each tablet contains 1 gram of dichlorophene. (b) Sponsor. See 023851 in § 510.600(c) of this.... Dogs—(1) Amount. Single dose of 1 tablet (1 gram of dichlorophene) for each 10 pounds of body weight...

  6. The accuracy, precision and sustainability of different techniques for tablet subdivision: breaking by hand and the use of tablet splitters or a kitchen knife.

    PubMed

    van Riet-Nales, Diana A; Doeve, Myrthe E; Nicia, Agnes E; Teerenstra, Steven; Notenboom, Kim; Hekster, Yechiel A; van den Bemt, Bart J F

    2014-05-15

    Tablets are frequently subdivided to lower the dose, to facilitate swallowing by e.g. children or older people or to save costs. Splitting devices are commonly used when hand breaking is difficult or painful. Three techniques for tablet subdivision were investigated: hand breaking, tablet splitter, kitchen knife. A best case drug (paracetamol), tablet (round, flat, uncoated, 500 mg) and operator (24-year student) were applied. Hundred tablets were subdivided by hand and by three devices of each of the following types: Fit & Healthy, Health Care Logistics, Lifetime, PillAid, PillTool, Pilomat tablet splitter; Blokker kitchen knife. The intra and inter device accuracy, precision and sustainability were investigated. The compliance to (adapted) regulatory requirements was investigated also. The accuracy and precision of hand broken tablets was 104/97% resp. 2.8/3.2% (one part per tablet considered; parts right/left side operator). The right/left accuracies of the splitting devices varied between 60 and 133%; the precisions 4.0 and 29.6%. The devices did not deteriorate over 100-fold use. Only hand broken tablets complied with all regulatory requirements. Health care professionals should realize that tablet splitting may result in inaccurate dosing. Authorities should undertake appropriate measures to assure good function of tablet splitters and, where feasible, to reduce the need for their use. Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

  7. Assessing Student Writing on Tablets

    ERIC Educational Resources Information Center

    Davis, Laurie Laughlin; Orr, Aline; Kong, Xiaojing; Lin, Chow-Hong

    2015-01-01

    There is increasing expectation that schools should be able to use tablets for a range of instructional and assessment purposes. This article considers the comparability of student writing on tablets and laptops to ensure that writing assessment is conducted in a way that is fair to all students. Data were collected from a sample of 826 students…

  8. Tablet PCs: The Write Approach

    ERIC Educational Resources Information Center

    Milner, Jacob

    2006-01-01

    This article discusses the transforming effects of tablet PCs in the classroom. As 1-to-1 computing becomes the goal on K-12 campuses, school districts are turning to this newer, pen-based technology. Saint Mary's School's new Lenovo ThinkPad X41 tablet PCs had transformed the way Saint Mary's teachers did their jobs. Teachers created outlines for…

  9. Comparative bioavailability study of cefuroxime axetil (equivalent to 500 mg cefuroxime/tablet) tablets (Zednad® versus Zinnat®) in healthy male volunteers.

    PubMed

    Asiri, Y A; Al-Hadiya, B M; Kadi, A A; Al-Khamis, K I; Mowafy, H A; El-Sayed, Y M

    2011-09-01

    This study was performed to investigate the bioequivalence of cefuroxime axetil tablets between a generic test product (A) Zednad® Tablet (500 mg cefuroxime/ tablet, Diamond Pharma, Syria), and the Reference Product (B) Zinnat® Tablet (500 mg cefuroxime/tablet, GlaxoSmithKline, Saudi Arabia). The bioavailability study was carried out for 24 healthy male volunteers. The subjects received 1 Zednad® Tablet (500 mg/ tablet) and 1 Zinnat® Tablet (500 mg/tablet) in a randomized, two-way crossover design fashion on 2 treatment days, after an overnight fast of at least 10 h, with a washout period of 7 days. 24 volunteers plus 2 alternatives completed the crossover. The bioanalysis of clinical plasma samples was accomplished by HPLC method, which was developed and validated in accordance with international guidelines. Pharmacokinetic parameters, determined by standard non-compartmental methods, and ANOVA statistics were calculated using SAS Statistical Software. The significance of a sequence effect was tested using the subjects nested in sequence as the error term. The 90% confidence intervals for the ratio between the test and reference product pharmacokinetic parameters of AUC0→t, AUC0→∞, and Cmax were calculated and found to be within the confidence limits of 80.00 - 125.00% for AUC0→t, AUC0→∞ and Cmax. The study demonstrated that the test product (A) was found bioequivalent to the reference product (B) following an oral dose of 500 mg tablet. Therefore, the two formulations were considered to be bioequivalent.

  10. Controlled-release tablet formulation of isoniazid.

    PubMed

    Jain, N K; Kulkarni, K; Talwar, N

    1992-04-01

    Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

  11. 21 CFR 520.1720a - Phenylbutazone tablets and boluses.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Phenylbutazone tablets and boluses. 520.1720a... Phenylbutazone tablets and boluses. (a) Specifications. Each tablet contains 100, 200, or 400 milligrams (mg), or...-mg or 1-g tablets, or 2- or 4-g boluses, in dogs and horses. (2) Nos. 000010 and 059130 for use of...

  12. 21 CFR 520.581 - Dichlorophene tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...) Specifications. Each tablet contains 1 gram of dichlorophene. (b) Sponsor. See 023851 in § 510.600(c) of this.... Dogs(1) Amount. Single dose of 1 tablet (1 gram of dichlorophene) for each 10 pounds of body weight. (2...

  13. The variability of ecstasy tablets composition in Brazil.

    PubMed

    Togni, Loraine R; Lanaro, Rafael; Resende, Rodrigo R; Costa, Jose L

    2015-01-01

    The content of ecstasy tablets has been changing over the years, and nowadays 3,4-methylenedioxymethamphetamine (MDMA) is not always present in the tablets. The aim of this study was to investigate the chemical composition in the seized tablets labeled as ecstasy. We analyzed samples from 150 different seizures made by Sao Paulo's State Police by gas chromatography-mass spectrometry. MDMA was present in 44.7% of the analyzed samples, and another twenty different active substances were identified in these tablets, such as caffeine, 2C-B, piperazines, amphetamines, phencyclidine, and others. Methamphetamine was present in 22% of these samples. The results demonstrate a huge shift in the pattern of trafficking of synthetic drugs, where MDMA has been replaced in tablets mostly by illicit psychoactive substances, in a clear attempt to bypass the law. The great variability in the tablets composition may lead to an increased risk of drug poisoning. © 2014 American Academy of Forensic Sciences.

  14. Smartphones and tablets: Reshaping radiation oncologists’ lives

    PubMed Central

    Gomez-Iturriaga, Alfonso; Bilbao, Pedro; Casquero, Francisco; Cacicedo, Jon; Crook, Juanita

    2012-01-01

    Background Smartphones and tablets are new handheld devices always connected to an information source and capable of providing instant updates, they allow doctors to access the most updated information and provide decision support at the point of care. Aim The practice of radiation oncology has always been a discipline that relies on advanced technology. Smartphones provide substantial processing power, incorporating innovative user interfaces and applications. Materials and methods The most popular smartphone and tablet app stores were searched for “radiation oncology” and “oncology” related apps. A web search was also performed searching for smartphones, tablets, oncology, radiology and radiation oncology. Results Smartphones and tablets allow rapid access to information in the form of podcasts, apps, protocols, reference texts, recent research and more. Conclusion With the rapidly changing advances in radiation oncology, the trend toward accessing resources via smartphones and tablets will only increase, future will show if this technology will improve clinical care. PMID:24669308

  15. Electronic acquisition of OSCE performance using tablets

    PubMed Central

    Hochlehnert, Achim; Schultz, Jobst-Hendrik; Möltner, Andreas; Tımbıl, Sevgi; Brass, Konstantin; Jünger, Jana

    2015-01-01

    Background: Objective Structured Clinical Examinations (OSCEs) often involve a considerable amount of resources in terms of materials and organization since the scores are often recorded on paper. Computer-assisted administration is an alternative with which the need for material resources can be reduced. In particular, the use of tablets seems sensible because these are easy to transport and flexible to use. Aim: User acceptance concerning the use of tablets during OSCEs has not yet been extensively investigated. The aim of this study was to evaluate tablet-based OSCEs from the perspective of the user (examiner) and the student examinee. Method: For two OSCEs in Internal Medicine at the University of Heidelberg, user acceptance was analyzed regarding tablet-based administration (satisfaction with functionality) and the subjective amount of effort as perceived by the examiners. Standardized questionnaires and semi-standardized interviews were conducted (complete survey of all participating examiners). In addition, for one OSCE, the subjective evaluation of this mode of assessment was gathered from a random sample of participating students in semi-standardized interviews. Results: Overall, the examiners were very satisfied with using tablets during the assessment. The subjective amount of effort to use the tablet was found on average to be “hardly difficult”. The examiners identified the advantages of this mode of administration as being in particular the ease of use and low rate of error. During the interviews of the examinees, acceptance for the use of tablets during the assessment was also detected. Discussion: Overall, it was found that the use of tablets during OSCEs was well accepted by both examiners and examinees. We expect that this mode of assessment also offers advantages regarding assessment documentation, use of resources, and rate of error in comparison with paper-based assessments; all of these aspects should be followed up on in further studies

  16. Electronic acquisition of OSCE performance using tablets.

    PubMed

    Hochlehnert, Achim; Schultz, Jobst-Hendrik; Möltner, Andreas; Tımbıl, Sevgi; Brass, Konstantin; Jünger, Jana

    2015-01-01

    Objective Structured Clinical Examinations (OSCEs) often involve a considerable amount of resources in terms of materials and organization since the scores are often recorded on paper. Computer-assisted administration is an alternative with which the need for material resources can be reduced. In particular, the use of tablets seems sensible because these are easy to transport and flexible to use. User acceptance concerning the use of tablets during OSCEs has not yet been extensively investigated. The aim of this study was to evaluate tablet-based OSCEs from the perspective of the user (examiner) and the student examinee. For two OSCEs in Internal Medicine at the University of Heidelberg, user acceptance was analyzed regarding tablet-based administration (satisfaction with functionality) and the subjective amount of effort as perceived by the examiners. Standardized questionnaires and semi-standardized interviews were conducted (complete survey of all participating examiners). In addition, for one OSCE, the subjective evaluation of this mode of assessment was gathered from a random sample of participating students in semi-standardized interviews. Overall, the examiners were very satisfied with using tablets during the assessment. The subjective amount of effort to use the tablet was found on average to be "hardly difficult". The examiners identified the advantages of this mode of administration as being in particular the ease of use and low rate of error. During the interviews of the examinees, acceptance for the use of tablets during the assessment was also detected. Overall, it was found that the use of tablets during OSCEs was well accepted by both examiners and examinees. We expect that this mode of assessment also offers advantages regarding assessment documentation, use of resources, and rate of error in comparison with paper-based assessments; all of these aspects should be followed up on in further studies.

  17. 21 CFR 520.763a - Dithiazanine iodide tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Dithiazanine iodide tablets. 520.763a Section 520... iodide tablets. (a) Chemical name. 3-Ethyl-2-[5-(3-ethyl - 2 - benzothiazolinylidene) - 1,3 - pentadienyl]-benzothiazolium iodide. (b) Specifications. Dithiazanine iodide tablets contain 10 milligrams, 50 milligrams, 100...

  18. 21 CFR 520.2220d - Sulfadimethoxine-ormetoprim tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfadimethoxine-ormetoprim tablets. 520.2220d Section 520.2220d Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Sulfadimethoxine-ormetoprim tablets. (a) Specifications. Each tablet contains 120 milligrams (100 milligrams of...

  19. 21 CFR 520.2041 - Pyrantel pamoate chewable tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Pyrantel pamoate chewable tablets. 520.2041 Section 520.2041 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... pamoate chewable tablets. (a) Specifications. Each tablet contains pyrantel pamoate equivalent to 22.7 or...

  20. Frosta: a new technology for making fast-melting tablets.

    PubMed

    Jeong, Seong Hoon; Fu, Yourong; Park, Kinam

    2005-11-01

    The fast-melting tablet (FMT) technology, which is known to be one of the most innovated methods in oral drug delivery systems, is a rapidly growing area of drug delivery. The initial success of the FMT formulation led to the development of various technologies. These technologies, however, still have some limitations. Recently, a new technology called Frosta (Akina) was developed for making FMTs. The Frosta technology utilises the conventional wet granulation process and tablet press for cost-effective production of tablets. The Frosta tablets are mechanically strong with friability of < 1% and are stable in accelerated stability conditions when packaged into a bottle container. They are robust enough to be packaged in multi-tablet vials. Conventional rotary tablet presses can be used for the production of the tablets and no other special instruments are required. Thus, the cost of making FMTs is lower than that of other existing technologies. Depending on the size, Frosta tablets can melt in < 10 s after placing them in the oral cavity for easy swallowing. The Frosta technology is ideal for wide application of FMTs technology to various drug and nutritional formulations.

  1. Magnetic resonance imaging for the in vivo evaluation of gastric-retentive tablets.

    PubMed

    Steingoetter, Andreas; Weishaupt, Dominik; Kunz, Patrick; Mäder, Karsten; Lengsfeld, Hans; Thumshirn, Miriam; Boesiger, Peter; Fried, Michael; Schwizer, Werner

    2003-12-01

    To develop a magnetic resonance imaging (MRI) technique for assessing in vivo properties of orally ingested gastric-retentive tablets under physiologic conditions. Tablets with different floating characteristics (tablet A-C) were marked with superparamagnetic Fe3O4 particles to analyze intragastric tablet position and residence time in human volunteers. Optimal Fe3O4 concentration was determined in vitro. Intragastric release characteristic of one slow-release tablet (tablet D) was analyzed by embedding gadolinium chelates (Gd-DOTA) as a drug model into the tablet. All volunteers underwent MRI in the sitting position. Tablet performance was analyzed in terms of relative position of tablet to intragastric meal level (with 100% at meal surface), intragastric residence time (min) and Gd-DOTA distribution volume (% of meal volume). Intragastric tablet floating performance and residence time of tablets (tablet A-D) as well as the intragastric Gd-DOTA distribution of tablet D could be monitored using MRI. Tablet floating performance was different between the tablets (A, 93%(95 - 9%); B, 80%(80 - 68%): C, 38%(63 - 32%); p < 0.05). The intragastric distribution volume of Gd-DOTA was 19.9% proximally and 35.5% distally. The use of MRI allows the assessment of galenic properties of orally ingested tablets in humans in seated position.

  2. [Study on preparation of phenols gastric floating tablet].

    PubMed

    Zhai, Xiao-Ling; Ni, Jian; Gu, Yu-Long

    2008-01-01

    To study the preparation of phenols gastric floating tablet. The tablets which were prepared using Eudragit IV, HPMC(K4M), MCC101 and Octadecanol as excipients were evaluated by vitro floatation and releasing performance. The pressure of preparationg was also study to select the optimal preparation. The tablets were successfully prepared in which the drug, Eudragit IV, Octadecanol were 31% respectively,and MCC101 was 7%. And 3-4 kg was found to be the eligible pressure. The study was found to be effective in the process of phenols gastric floating tablet.

  3. Galileo's Telescopy and Jupiter's Tablet

    NASA Astrophysics Data System (ADS)

    Usher, P. D.

    2003-12-01

    A previous paper (BAAS 33:4, 1363, 2001) reported on the dramatic scene in Shakespeare's Cymbeline that features the descent of the deity Jupiter. The paper suggested that the four ghosts circling the sleeping Posthumus denote the four Galilean moons of Jupiter. The god Jupiter commands the ghosts to lay a tablet upon the prone Posthumus, but says that its value should not be overestimated. When Posthumus wakens he notices the tablet, which he calls a "book." Not only has the deity's "tablet" become the earthling's "book," but it appears that the book has covers which Posthumus evidently recognizes because without even opening the book he ascribes two further properties to it: rarity, and the very property that Jupiter had earlier attributed, viz. that one must not read too much into it. The mystery deepens when the Jovian gift undergoes a second metamorphosis, to "label." With the help of the OED, the potentially disparate terms "tablet," "book," and "label," may be explained by terms appropriate either to supernatural or worldly beings. "Tablet" may recognize the Mosaic artifact, whereas "book" and "label" are probably mundane references to Galileo's Sidereus Nuncius which appeared shortly before Cymbeline. The message of the Olympian god indicates therefore that the book is unique even as its contents have limited value. The first property celebrates the fact that Galileo's book is the first of its kind, and the second advises that all results except the discovery of Jupiter's moons have been reported earlier, in Hamlet.

  4. 21 CFR 520.1696d - Penicillin V tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Penicillin V tablets. 520.1696d Section 520.1696d... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1696d Penicillin V tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000...

  5. 21 CFR 520.1696d - Penicillin V tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Penicillin V tablets. 520.1696d Section 520.1696d... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1696d Penicillin V tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000...

  6. Efficacy of Flocculating and Other Emergency Water Purification Tablets

    DTIC Science & Technology

    1993-05-01

    iodine tablet {1). The deficiencies identified with iodine tablets included slaw kill of Giardia cysts at law temperatures, medicinal taste and odor ...and the fact that undissolved solids, color and odor in field water ~e not rerroved. A market search for a new emergency water purification...tablet, or compound , was undertaken. The tablet had to be cOITll!Ercially available, nondevelopmental and satisfy the new military requirements. The

  7. Does the performance of wet granulation and tablet hardness affect the drug dissolution profile of carvedilol in matrix tablets?

    PubMed

    Košir, Darjan; Ojsteršek, Tadej; Vrečer, Franc

    2018-06-14

    Wet granulation is mostly used process for manufacturing matrix tablets. Compared to the direct compression method, it allows for a better flow and compressibility properties of compression mixtures. Granulation, including process parameters and tableting, can influence critical quality attributes (CQAs) of hydrophilic matrix tablets. One of the most important CQAs is the drug release profile. We studied the influence of granulation process parameters (type of nozzle and water quantity used as granulation liquid) and tablet hardness on the drug release profile. Matrix tablets contained HPMC K4M hydrophilic matrix former and carvedilol as a model drug. The influence of selected HPMC characteristics on the drug release profile was also evaluated using two additional HPMC batches. For statistical evaluation, partial least square (PLS) models were generated for each time point of the drug release profile using the same number of latent factors. In this way, it was possible to evaluate how the importance of factors influencing drug dissolution changes in dependence on time throughout the drug release profile. The results of statistical evaluation show that the granulation process parameters (granulation liquid quantity and type of nozzle) and tablet hardness significantly influence the release profile. On the other hand, the influence of HPMC characteristics is negligible in comparison to the other factors studied. Using a higher granulation liquid quantity and the standard nozzle type results in larger granules with a higher density and lower porosity, which leads to a slower drug release profile. Lower tablet hardness also slows down the release profile.

  8. [The effects of various factors on the in vitro velocity of drug release from repository tablets. Part 4: Isoniazid (Rimicid) respository tablets (author's transl)].

    PubMed

    Tomassini, L; Michailova, D; Naplatanova, D; Slavtschev, P

    1979-12-01

    The authors investigated the release of isoniazid from repository tablets as related to form, processing technology, strength constant and storage for 5 years. On determining the diffusion coefficient (D), the initial dissolution rate (Vo) and the time required for the diffusion of the releasing medium to the middle of the tablet (t1/2), it was found that the difference in release rate between the flat and the biconvex tablets is small. Furthermore, it was stated that the three-layer tablets have very high D and Vo values and very low t1/2 values, for what reason they are unsuited for repository tablets of the composition under investigation. Moreover, it was found that an increase of the strength constant does not affect the D, t1/2 and Vo values, and that the release of isoniazid is retarded only in flat tablets with the highest strength constant. Storage exerts no effect on the drug release from these tablets. The industrial production of these tablets is under way.

  9. To Study Capping or Lamination Tendency of Tablets Through Evaluation of Powder Rheological Properties and Tablet Mechanical Properties of Directly Compressible Blends.

    PubMed

    Dudhat, Siddhi M; Kettler, Charles N; Dave, Rutesh H

    2017-05-01

    Air entrapment efficiency of the powders is one of the main factors leading to occurrence of capping or lamination tendency of tablets manufactured from the directly compressible powder blends. The purpose of the current research was to study this underlying cause leading to occurrence of capping or lamination of tablets through evaluation of powder rheological properties. Powder blends were prepared by addition of 0% w/w to 100% w/w of individual active pharmaceutical ingredient (API) [two model API: acetaminophen (APAP) and ibuprofen (IBU)] with microcrystalline cellulose without and with 0.5% w/w Magnesium Stearate as lubricant. Powder rheological properties were analyzed using FT4 Powder Rheometer for dynamic, bulk, and shear properties. Tablet mechanical properties of the respective blends were studied by determining the ability of the material to form tablet of specific strength under applied compaction pressure through tabletability profile. The results showed that powder rheometer distinguished the powder blends based on their ability to relieve entrapped air along with the distinctive flow characteristics. Powder blend prepared with increasing addition of APAP displayed low powder permeability as compared to IBU blends with better powder permeability, compressibility and flow characteristics. Also, lubrication of the APAP blends did not ease their ability to relieve air. Tabletability profiles revealed the potential occurrence of capping or lamination in tablets prepared from the powder blends with high APAP content. This study can help scientist to understand tableting performance at the early-developmental stages and can avoid occurrence capping and lamination of tablets.

  10. 21 CFR 520.1805 - Piperazine phosphate with thenium closylate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... tablets. 520.1805 Section 520.1805 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... § 520.1805 Piperazine phosphate with thenium closylate tablets. (a) Specifications. Each scored tablet... chapter. (c) Conditions of use—(1) Amount. Administer orally to dogs as follows: Number of Tablets at Each...

  11. 21 CFR 520.622a - Diethylcarbamazine citrate tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Diethylcarbamazine citrate tablets. 520.622a... Diethylcarbamazine citrate tablets. (a) Sponsors. (1) See 015579 in § 510.600(c) of this chapter for use of 50, 200, and 400 milligram tablets for prevention of heartworm disease in dogs and as an aid in the treatment...

  12. In-vitro characterization of 5-aminosalicylic acid release from MMX mesalamine tablets and determination of tablet coating thickness.

    PubMed

    Tenjarla, Srini; Abinusawa, Adeyinka

    2011-01-01

    Substantial variability in gastrointestinal pH is observed in patients with ulcerative colitis (UC). We characterized the effect of pH on 5-aminosalicylic acid (5-ASA) release from MMX mesalamine tablets (Shire Pharmaceuticals Inc., Wayne, PA, USA), examined thickness/uniformity of tablet film coatings, and explored the influence of simulating altered gastrointestinal motility. Nondestructive, three-dimensional, terahertz pulse imaging (TPI) was used to characterize the film coating of three lots of MMX mesalamine tablets (n=36). Thereafter, 5-ASA release from these tablets was evaluated using United States Pharmacopeia (USP) apparatus II at pH 6.8 and 7.2. Onset of tablet film-coat breach and mean dissolution time were determined for each lot. 5-ASA release was also assessed at three different paddle rotation speeds (50, 75, and 100 rpm) at pH 7.2. The mean ± SD film-coating thickness of the three lots of MMX mesalamine tablets were 109.2 ± 16.8, 113.1 ± 19.5, and 113.8 ± 19.8 μM, respectively. At pH 6.8 (100 rpm), the onset of film-coat breach was 10-30 minutes, whereas at pH 7.2 this was observed within 10 minutes. 5-ASA release was uniform at both pH conditions, with minimal lot-to-lot variability. Complete drug release was achieved within 6 hours under both pH conditions. 5-ASA release increased in proportion with paddle speed, but remained prolonged at all speeds. 5-ASA release from MMX mesalamine is unaffected by normal variations in simulated intracolonic pH. The dissolution profile of 5-ASA from MMX mesalamine tablets may be attributed to consistent outer film coatings and the hydrogel-forming matrix that controls the drug release after dissolution of the film coating.

  13. Solid dispersion tablets of breviscapine with polyvinylpyrrolidone K30 for improved dissolution and bioavailability to commercial breviscapine tablets in beagle dogs.

    PubMed

    Cong, Wenjuan; Shen, Lan; Xu, Desheng; Zhao, Lijie; Ruan, Kefeng; Feng, Yi

    2014-09-01

    Breviscapine, one of cardiovascular drugs extracted from a Chinese herb Erigeron breviscapinus, has been frequently used to treat cardiovascular diseases such as hypertension, angina pectoris, coronary heart disease and stroke. However, its poor water solubility and low bioavailability in vivo severely restrict the clinical application. To overcome these drawbacks, breviscapine solid dispersion tablets consisting of breviscapine, polyvinylpyrrolidone K30 (PVP K30), microcrystalline cellulose and crospovidone were appropriately prepared. In vitro dissolution profiles showed that breviscapine released percentage of solid dispersion tablets reached 90 %, whereas it was only 40 % for commercial breviscapine tablets. Comparative pharmacokinetic study between solid dispersion tablets and commercial products was investigated on the normal beagle dogs after oral administration. Results showed that the bioavailability of breviscapine was greatly increased by 3.45-fold for solid dispersion tablets. The greatly improved dissolution rate and bioavailability might be attributed to intermolecular hydrogen bonding reactions between PVP K30 and scutellarin. These findings suggest that our solid dispersion tablets can greatly improve the bioavailability as well as the dissolution rate of breviscapine.

  14. 21 CFR 520.1900 - Primidone tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... for use of 50 and 250 milligram tablets. (c) Conditions of use in dogs—(1) Amount. Twenty-five..., epileptiform convulsions, viral encephalitis, distemper, and hardpad disease that occurs as a clinically recognizable lesion in certain entities in dogs.1 (3) Limitations. The tablets may be administered whole or...

  15. 21 CFR 520.2088 - Roxarsone tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... period. Withdraw 5 days before slaughter. Use as sole source of organic arsenic. (ii) Growing chickens—(a.... Withdraw 5 days before slaughter. Use as sole source of organic arsenic. (b)(1) Specifications. Each tablet... slaughter. Use as sole source of organic arsenic. (ii) [Reserved] (c)(1) Specifications. Each tablet...

  16. The Impact of Granule Density on Tabletting and Pharmaceutical Product Performance.

    PubMed

    van den Ban, Sander; Goodwin, Daniel J

    2017-05-01

    The impact of granule densification in high-shear wet granulation on tabletting and product performance was investigated, at pharmaceutical production scale. Product performance criteria need to be balanced with the need to deliver manufacturability criteria to assure robust industrial scale tablet manufacturing processes. A Quality by Design approach was used to determine in-process control specifications for tabletting, propose a design space for disintegration and dissolution, and to understand the permitted operating limits and required controls for an industrial tabletting process. Granules of varying density (filling density) were made by varying water amount added, spray rate, and wet massing time in a design of experiment (DoE) approach. Granules were compressed into tablets to a range of thicknesses to obtain tablets of varying breaking force. Disintegration and dissolution performance was evaluated for the tablets made. The impact of granule filling density on tabletting was rationalised with compressibility, tabletability and compactibility. Tabletting and product performance criteria provided competing requirements for porosity. An increase in granule filling density impacted tabletability and compactability and limited the ability to achieve tablets of adequate mechanical strength. An increase in tablet solid fraction (decreased porosity) impacted disintegration and dissolution. An attribute-based design space for disintegration and dissolution was specified to achieve both product performance and manufacturability. The method of granulation and resulting granule filling density is a key design consideration to achieve both product performance and manufacturability required for modern industrial scale pharmaceutical product manufacture and distribution.

  17. Urinary excretion of ciprofloxacin after administration of extended release tablets in healthy volunteers. Swellable drug-polyelectrolyte matrix versus bilayer tablets.

    PubMed

    Guzmán, M L; Romañuk, C B; Sanchez, M F; Luciani Giacobbe, L C; Alarcón-Ramirez, L P; Battistini, F D; Alovero, F L; Jimenez-Kairuz, A F; Manzo, R H; Olivera, María Eugenia

    2018-02-01

    This paper builds on a previous paper in which new ciprofloxacin extended-release tablets were developed based on a ciprofloxacin-based swellable drug polyelectrolyte matrix (SDPM-CIP). The matrix contains a molecular dispersion of ciprofloxacin ionically bonded to the acidic groups of carbomer, forming the polyelectrolyte-drug complex CB-CIP. This formulation showed that the release profile of the ciprofloxacin bilayer tablets currently commercialised can be achieved with a simpler strategy. Thus, since ciprofloxacin urine concentrations are associated with the clinical cure of urinary tract infections, the goal of this work was to compare the urinary excretion of SDPM-CIP tablets with those of the CIPRO XR® bilayer tablets. A batch of SDPM-CIP tablets was manufactured by the wet granulation method and the CB-CIP ionic complex was obtained in situ. Fasted healthy volunteers received a single oral dose of 500 mg ciprofloxacin of either formulation in a randomised crossover study. Urinary concentrations were assessed by HPLC at intervals up to 36 h. Pharmacokinetic parameters (rate of urinary excretion, maximum urine excretion rate, t max , area under the curve, amount and percentage of the ciprofloxacin dose excreted in urine) showed no statistical differences between both formulations at any of the time intervals of collection. The processing conditions to obtain SDPM-CIP tablets are easy to scale up since they involve technology currently employed in the pharmaceutical industry and the process is less challenging to implement. In addition, SDPM-CIP tablets met pharmacopoeial quality specifications.

  18. Neuroleptic bioequivalency: tablet versus concentrate.

    PubMed

    Fann, W E; Moreira, A F

    1985-01-01

    Two forms of the antipsychotic neuroleptic molindone were administered to newly admitted psychotic patients. A coated tablet was administered for ten days, followed by administration of liquid concentrate in equivalent doses for four days. Plasma was analyzed by gas chromatography with electron capture for the parent compound following each dosing phase. Our data suggest that oral doses of the tablet and concentrate forms of this neuroleptic are equivalent in clinical bioavailability.

  19. 21 CFR 520.82b - Aminopropazine fumarate, neomycin sulfate tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Aminopropazine fumarate, neomycin sulfate tablets... Aminopropazine fumarate, neomycin sulfate tablets. (a) Specifications. The drug is in tablet form. Each tablet... sulfate equivalent to 50 milligrams of neomycin base. (b) Sponsor. See No. 000061 in § 510.600(c) of this...

  20. Understanding the Delamination Risk of a Trilayer Tablet Using Minipiloting Tools.

    PubMed

    Tao, Jing; Robertson-Lavalle, Sophia; Pandey, Preetanshu; Badawy, Sherif

    2017-11-01

    A multilayer tablet is one of the formulation options used to mitigate chemical and physical incompatibility between different drug substances. Feasibility studies of multilayer tablets are often conducted using round flat-faced punch tooling. However, the link between different tooling designs and multilayer tablet performance is not well established. This study uses a prototype trilayer tablet and examines tooling design considerations when conducting small-scale studies to gauge the risk of interfacial defects. The impact of tablet weight and dimensions was evaluated to gain understanding of the effect of scale-up/down of tablet size. The factors in tooling selection, including tablet shape, cup depth, and size of embossing were evaluated to gain insight on the impact of tooling design on the interfacial strength of the trilayer tablet. It was found that tablet weight and dimensions can significantly affect the interfacial strength due to their impact on force transmission during compression and the retardation force from the die wall during ejection. Round flat-faced tooling generated trilayer tablets of the strongest interfacial strength compared to typical commercial tablets-oval shaped with concave surfaces. These factors should be accounted for when using round flat compacts to assess the interface risks of a multilayer tablet. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  1. 21 CFR 520.370 - Cefpodoxime tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Cefpodoxime tablets. 520.370 Section 520.370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.370 Cefpodoxime tablets. (a...

  2. 21 CFR 520.455 - Clomipramine tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Clomipramine tablets. 520.455 Section 520.455 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.455 Clomipramine tablets. (a...

  3. 21 CFR 520.804 - Enalapril tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Enalapril tablets. 520.804 Section 520.804 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.804 Enalapril tablets. (a...

  4. 21 CFR 520.455 - Clomipramine tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Clomipramine tablets. 520.455 Section 520.455 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.455 Clomipramine tablets. (a...

  5. 21 CFR 520.370 - Cefpodoxime tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Cefpodoxime tablets. 520.370 Section 520.370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.370 Cefpodoxime tablets. (a...

  6. 21 CFR 520.312 - Carnidazole tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Carnidazole tablets. 520.312 Section 520.312 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.312 Carnidazole tablets. (a...

  7. 21 CFR 520.370 - Cefpodoxime tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Cefpodoxime tablets. 520.370 Section 520.370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.370 Cefpodoxime tablets. (a...

  8. 21 CFR 520.812 - Enrofloxacin tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Enrofloxacin tablets. 520.812 Section 520.812 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.812 Enrofloxacin tablets. (a...

  9. 21 CFR 520.455 - Clomipramine tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Clomipramine tablets. 520.455 Section 520.455 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.455 Clomipramine tablets. (a...

  10. 21 CFR 520.312 - Carnidazole tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Carnidazole tablets. 520.312 Section 520.312 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.312 Carnidazole tablets. (a...

  11. 21 CFR 520.581 - Dichlorophene tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Dichlorophene tablets. 520.581 Section 520.581 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.581 Dichlorophene tablets. (a...

  12. 21 CFR 520.455 - Clomipramine tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Clomipramine tablets. 520.455 Section 520.455 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.455 Clomipramine tablets. (a...

  13. 21 CFR 520.804 - Enalapril tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Enalapril tablets. 520.804 Section 520.804 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.804 Enalapril tablets. (a...

  14. 21 CFR 520.312 - Carnidazole tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Carnidazole tablets. 520.312 Section 520.312 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.312 Carnidazole tablets. (a...

  15. Enhancing Student Performance Using Tablet Computers

    ERIC Educational Resources Information Center

    Enriquez, Amelito G.

    2010-01-01

    Tablet PCs have the potential to change the dynamics of classroom interaction through wireless communication coupled with pen-based computing technology that is suited for analyzing and solving engineering problems. This study focuses on how tablet PCs and wireless technology can be used during classroom instruction to create an Interactive…

  16. Are multisource levothyroxine sodium tablets marketed in Egypt interchangeable?

    PubMed

    Abou-Taleb, Basant A; Bondok, Maha; Nounou, Mohamed Ismail; Khalafallah, Nawal; Khalil, Saleh

    2018-02-01

    A clinical study was initiated in response to patients' complaints, supported by the treating physicians, of suspected differences in efficacy among multisource levothyroxine sodium tablets marketed in Egypt. The study design was a multiple dose (100μg levothyroxine sodium tablet once daily for 6 months) and involved 50 primary hypothyroidism female patients (5 equal groups). Tablets administered included five tablet batches (two brands, three origin locations) purchased from local pharmacies in Alexandria. Assessment parameters (measured on consecutive visits) included the thyroid stimulating hormone, total and free levothyroxine. Tablet dissolution rate was determined (BP/EP 2014 & USP 2014). In vitro vs in vivovs correlations were developed. Clinical and pharmaceutical data confirmed inter-brand and inter-source differences in efficacy. Correlations examined indicated potential usefulness of in vitro dissolution test in detecting poor performing levothyroxine sodium tablets during shelf life. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  17. Genuine sildenafil tablets sold in Brazil disguised as MDMA.

    PubMed

    Coelho Neto, José; Faraco, Renata F P; Alves, Cíntia F; Castro, Stela M M; Machado, Yuri

    2018-02-01

    MDMA and sildenafil are two examples among many substances consumed in "raves", as well as in other types of "recreative" social events nowadays. During the first six months of 2017, five cases of supposedly MDMA tablets seized by local law enforcement forces in the state of Minas Gerais, Brazil, and brought to our forensic laboratory for examination, attracted our attention among dozens of others, as the tablets apprehended in these cases were, in fact, colorfully painted versions of genuine, pentagon-shaped, sildenafil tablets, freely available for sale in local pharmacies and drugstores. Physical profiling, together with ATR-FTIR spectral matching, multi-component/deconvolution analysis and correlation were employed to prove that these tablets were genuine sildenafil tablets from a specific manufacturer, painted in a colorful way so that they could be marketed as MDMA tablets to unsuspecting buyers. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Bioavailability and stability of erythromycin delayed release tablets.

    PubMed

    Ogwal, S; Xide, T U

    2001-12-01

    Erythromycin is available as the free base, ethylsuccinate, estolate, stearate, gluceptate, and lactobionate derivatives. When given orally erythromycin and its derivatives except the estolate are inactivated to some extent by the gastric acid and poor absorption may result. To establish whether delayed release erythromycin tablets meet the bioequivalent requirement for the market. Sectrophotometric analysis was used to determine the dissolution percentage of the tablets in vitro. High performance liquid chromatography and IBM/XT microcomputer was used to determine the bioavailability and pharmacokinetic parameters in vivo. Dissolution percentage in thirty minutes reached 28.9% and in sixty minutes erythromycin was completely released. The parameters of the delayed release tablets were Tlag 2.3 hr, Tmax.4.5 hr, and Cmax 2.123 g/ml Ka 0.38048 hr(-1) T (1/2) 1.8 hr, V*C/F 49.721 AUC 12.9155. The relative bioavailability of erythromycin delayed release tablet to erythromycin capsules was 105.31% The content, appearance, and dissolution bioavailability of delayed release erythromycin tablets conforms to the United States pharmacopoeia standards. The tablets should be stored in a cool and dry place in airtight containers and the shelf life is temporarily assigned two years.

  19. 21 CFR 520.623 - Diethylcarbamazine citrate, oxibendazole chewable tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Diethylcarbamazine citrate, oxibendazole chewable tablets. 520.623 Section 520.623 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... § 520.623 Diethylcarbamazine citrate, oxibendazole chewable tablets. (a) Specifications. Each tablet...

  20. Novel platens to measure the hardness of a pentagonal shaped tablet.

    PubMed

    Malladi, Jaya; Sidik, Kurex; Wu, Sutan; McCann, Ryan; Dougherty, Jeffrey; Parab, Prakash; Carragher, Thomas

    2017-03-01

    Tablet hardness, a measure of the breaking force of a tablet, is based on numerous factors. These include the shape of the tablet and the mode of the application of force. For instance, when a pentagonal-shaped tablet was tested with a traditional hardness tester with flat platens, there was a large variation in hardness measurements. This was due to the propensity of vertices of the tablet to crush, referred to as an "improper break". This article describes a novel approach to measure the hardness of pentagonal-shaped tablets using modified platens. The modified platens have more uniform loading than flat platens. This is because they reduce loading on the vertex of the pentagon and apply forces on tablet edges to generate reproducible tablet fracture. The robustness of modified platens was assessed using a series of studies, which included feasibility and Gauge Repeatability & Reproducibility (R&R) studies. A key finding was that improper breaks, generated frequently with a traditional hardness tester using flat platens, were eliminated. The Gauge R&R study revealed that the tablets tested with novel platens generated consistent values in hardness measurements, independent of batch, hardness level, and day of testing, operator and tablet dosage strength.

  1. An index for evaluating difficulty of Chewing Index for chewable tablets.

    PubMed

    Gupta, Abhay; Chidambaram, Nallaperumal; Khan, Mansoor A

    2015-02-01

    Chewing difficulty index, a potential measure of difficulty in chewing the chewable tablets, has been described herein as the product of tablet thickness and tablet hardness measured under the diametral loading. The proposed index was evaluated by measuring the dimensions and mechanical strength of commercial and in-house prepared chewable tablets. Data collected on tablets with different thickness but same hardness or tensile strength suggests that the proposed index provides a good assessment of the force needed to chew the chewable tablets. Influence of brief exposure to salivary fluid during chewing on the mechanical strength of the chewable tablets was also evaluated. Thirty seconds exposure to the simulated salivary fluid was also found to significantly reduce (p < 0.05) the hardness and the chewing difficulty index of a number of evaluated chewable tablet drug products.

  2. Application of face centred central composite design to optimise compression force and tablet diameter for the formulation of mechanically strong and fast disintegrating orodispersible tablets.

    PubMed

    Pabari, Ritesh M; Ramtoola, Zebunnissa

    2012-07-01

    A two factor, three level (3(2)) face centred, central composite design (CCD) was applied to investigate the main and interaction effects of tablet diameter and compression force (CF) on hardness, disintegration time (DT) and porosity of mannitol based orodispersible tablets (ODTs). Tablet diameters of 10, 13 and 15 mm, and CF of 10, 15 and 20 kN were studied. Results of multiple linear regression analysis show that both the tablet diameter and CF influence tablet characteristics. A negative value of regression coefficient for tablet diameter showed an inverse relationship with hardness and DT. A positive value of regression coefficient for CF indicated an increase in hardness and DT with increasing CF as a result of the decrease in tablet porosity. Interestingly, at the larger tablet diameter of 15 mm, while hardness increased and porosity decreased with an increase in CF, the DT was resistant to change. The optimised combination was a tablet of 15 mm diameter compressed at 15 kN showing a rapid DT of 37.7s and high hardness of 71.4N. Using these parameters, ODTs containing ibuprofen showed no significant change in DT (ANOVA; p>0.05) irrespective of the hydrophobicity of the ibuprofen. Copyright © 2012 Elsevier B.V. All rights reserved.

  3. 21 CFR 520.1660c - Oxytetracycline hydrochloride tablets/boluses.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Oxytetracycline hydrochloride tablets/boluses. 520....1660c Oxytetracycline hydrochloride tablets/boluses. (a) Specifications. Each tablet or bolus contains 250, 500, or 1,000 milligrams of oxytetracycline hydrochloride. (b) Sponsors. For sponsors in § 510...

  4. [Cost-effective analysis of rotation from sustained-release morphine tablet to transdermal fentanyl of matrix type or sustained-release oxycodone tablet].

    PubMed

    Ise, Yuya; Wako, Tetsuya; Miura, Yoshihiko; Katayama, Shirou; Shimizu, Hisanori

    2009-12-01

    The present study was undertaken to determine the pharmacoeconomics of switching from sustained-release morphine tablet to matrix type (MT) of transdermal fontanel or sustained-release Oxycodone tablet. Cost-effective analysis was performed using a simulation model along with decision analysis. The analysis was done from the payer's perspective. The cost-effective ratio/patient of transdermal MT fontanel (22, 539 yen)was lower than that of sustained -release Oxycodone tablet (23, 630 yen), although a sensitivity analysis could not indicate that this result was reliable. These results suggest the possibility that transdermal MT fontanel was much less expensive than a sustained-release Oxycodone tablet.

  5. Investigation on Raman spectral features of a coated tablet under variation of its orientation respective to laser illumination and measurement of nominal coating thickness of packed tablets.

    PubMed

    Kim, Jaejin; Hwang, Jinyoung; Woo, Young-Ah; Chung, Hoeil

    2016-11-30

    To investigate Raman spectral features of a coated biconvex tablet under variation of its orientation respective to laser illumination, spectra of the tablet were collected by illuminating laser on 12 different locations on the tablet with 3 different illumination angles of 45, 75 and 90°. The spectral variations were more substantial when the tablet faces with engraved letters and greater surface curvature were measured, since the sampled volume of coating relative to that of a core tablet changed significantly under these circumstances as the illumination angle varied. The preliminary examination confirmed that the acquisition of tablet-representative spectra was the requisite for reliable measurement of coating thickness. Then, to mimic real monitoring of coating process, Raman spectra were directly collected on a packing of 30 tablets with repetition of random tablet packing up to 15 times and univariate models utilizing the intensity of coating peak at 638cm -1 were developed using the cumulatively averaged spectra with an average weight of the 30 tablets as a reference. To acquire less tablet orientation-sensitive spectra, a wide area illumination (WAI) scheme providing a large sampling area (28.3mm 2 ) on a tablet with a long focal length (∼25cm) was employed. The averaging of the first to seventh spectra, equivalently utilizing more packing-representative spectra for quantitative analysis, made the measurement of nominal coating thickness of packed tablets accurate. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Cyclodextrins as excipients in tablet formulations.

    PubMed

    Conceição, Jaime; Adeoye, Oluwatomide; Cabral-Marques, Helena Maria; Lobo, José Manuel Sousa

    2018-04-22

    This paper aims to provide a critical review of cyclodextrins as excipients in tablet formulations, highlighting: (i) the principal pharmaceutical applications of cyclodextrins; (ii) the most relevant technological aspects in pharmaceutical formulation development; and (iii) the actual regulatory status of cyclodextrins. Moreover, several illustrative examples are presented. Cyclodextrins can be used as complexing excipients in tablet formulations for low-dose drugs. By contrast, for medium-dose drugs and/or when the complexation efficiency is low, the methods to enhance the complexation efficiency play a key part in reducing the cyclodextrin quantity. In addition, these compounds are used as fillers, disintegrants, binders and multifunctional direct compression excipients of the tablets. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Damage-tolerance strategies for nacre tablets.

    PubMed

    Wang, Shengnan; Zhu, Xinqiao; Li, Qiyang; Wang, Rizhi; Wang, Xiaoxiang

    2016-05-01

    Nacre, a natural armor, exhibits prominent penetration resistance against predatory attacks. Unraveling its hierarchical toughening mechanisms and damage-tolerance design strategies may provide significant inspiration for the pursuit of high-performance artificial armors. In this work, relationships between the structure and mechanical performance of nacre were investigated. The results show that other than their brick-and-mortar structure, individual nacre tablets significantly contribute to the damage localization of nacre. Affected by intracrystalline organics, the tablets exhibit a unique fracture behavior. The synergistic action of the nanoscale deformation mechanisms increases the energy dissipation efficiency of the tablets and contributes to the preservation of the structural and functional integrity of the shell. Copyright © 2016 Elsevier Inc. All rights reserved.

  8. Interfacial elastic relaxation during the ejection of bi-layered tablets.

    PubMed

    Anuar, M S; Briscoe, B J

    2010-03-15

    The predilection of a bi-layered tablet to fail in the interface region after its initial formation in the compaction process reduces its practicality as a choice for controlled release solid drug delivery system. Hence, a fundamental appreciation of the governing mechanism that causes the weakening of the interfacial bonds within the bi-layered tablet is crucial in order to improve the overall bi-layered tablet mechanical integrity. This work has shown that the occurrence of the elastic relaxation in the interface region during the ejection stage of the compaction process decreases with the increase in the bi-layered tablet interface strength. This is believed to be due to the increase in the plastic bonding in the interface region. The tablet diametrical elastic relaxation affects the tablet height elastic relaxation, where the impediment of the tablet height expansion is observed when the interface region experiences a diametrical expansion. 2009 Elsevier B.V. All rights reserved.

  9. Embolic stroke associated with injection of buprenorphine tablets.

    PubMed

    Lim, C C Tchoyoson; Lee, Sze Haur; Wong, Yee-Choon; Hui, Francis

    2009-09-15

    Drug users who crush, dissolve, and inject buprenorphine tablets parenterally may be at risk of severe thromboembolic complications or death. We describe patients with neurologic complications after injecting buprenorphine tablets. Brain MRI including diffusion-weighted imaging (DWI) in patients admitted to the neurologic department after injecting buprenorphine tablets were reviewed. Seven men had neurologic complications after buprenorphine tablet injection. In 5 patients, multiple small scattered hyperintense lesions were detected on DWI in the cortex, white matter, and basal ganglia of the cerebral hemisphere; one patient had a single small lesion. The side of MRI abnormality corresponded to the side of needle marks on the neck except in one patient who had bilateral injections. One patient, who denied injecting into the neck, had DWI abnormalities in the middle cerebral artery territory on one side and occlusion of the ipsilateral internal carotid artery. Buprenorphine tablets can be intentionally or inadvertently injected into the carotid artery, causing a characteristic appearance on diffusion-weighted imaging, consistent with embolic cerebral infarction.

  10. Tensile and shear methods for measuring strength of bilayer tablets.

    PubMed

    Chang, Shao-Yu; Li, Jian-Xin; Sun, Changquan Calvin

    2017-05-15

    Both shear and tensile measurement methods have been used to quantify interfacial bonding strength of bilayer tablets. The shear method is more convenient to perform, but reproducible strength data requires careful control of the placement of tablet and contact point for shear force application. Moreover, data obtained from the shear method depend on the orientation of the bilayer tablet. Although more time-consuming to perform, the tensile method yields data that are straightforward to interpret. Thus, the tensile method is preferred in fundamental bilayer tableting research to minimize ambiguity in data interpretation. Using both shear and tensile methods, we measured the mechanical strength of bilayer tablets made of several different layer combinations of lactose and microcrystalline cellulose. We observed a good correlation between strength obtained by the tensile method and carefully conducted shear method. This suggests that the shear method may be used for routine quality test of bilayer tablets during manufacturing because of its speed and convenience, provided a protocol for careful control of the placement of the tablet interface, tablet orientation, and blade is implemented. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Pharmacokinetics of ketorolac tromethamine compression-coated tablets for colon delivery.

    PubMed

    Vemula, Sateesh Kumar; Veerareddy, Prabhakar Reddy; Devadasu, Venkat Ratnam

    2014-08-01

    Present research efforts are focused in developing compression-coated ketorolac tromethamine tablets to improve the drug levels in colon by retarding the drug release in the stomach and small intestine. To achieve this objective, core tablets containing ketorolac tromethamine were prepared by direct compression and compression coated with sodium alginate. The developed tablets were evaluated for physical properties, in vitro drug release, X-ray imaging, and pharmacokinetic studies in human volunteers. Based on the in vitro drug release study, the optimized formulation showed very little drug release (6.75 ± 0.49 %) in the initial lag period of 5 h, followed by progressive release up to 97.47 ± 0.93 % within 24 h. The X-ray imaging of tablets in human volunteers showed that the tablets reached the colon without disintegrating in the upper gastrointestinal tract. From the pharmacokinetic study, the C max of colon-targeted tablets was 3,486.70 ng/ml at T max 10 h, whereas in the case of immediate-release tablets, the C max of 4,506.31 ng/ml at T max 2 h signifies the ability of compression-coated tablets to target the colon. In conclusion, compression-coated tablets are suitable to deliver ketorolac tromethamine to the colon.

  12. Portable Tablets in Science Museum Learning: Options and Obstacles

    ERIC Educational Resources Information Center

    Gronemann, Sigurd Trolle

    2017-01-01

    Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people's learning with portable tablets matches the…

  13. 21 CFR 520.1696d - Penicillin V potassium tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Penicillin V potassium tablets. 520.1696d Section... Penicillin V potassium tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000 units) or 250 milligrams (400,000 units) of penicillin V. (b) Sponsors. See...

  14. 21 CFR 520.1696d - Penicillin V potassium tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Penicillin V potassium tablets. 520.1696d Section... Penicillin V potassium tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000 units) or 250 milligrams (400,000 units) of penicillin V. (b) Sponsors. See...

  15. 21 CFR 520.1696d - Penicillin V potassium tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Penicillin V potassium tablets. 520.1696d Section... Penicillin V potassium tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000 units) or 250 milligrams (400,000 units) of penicillin V. (b) Sponsors. See...

  16. Characterization of the Roman curse tablet

    NASA Astrophysics Data System (ADS)

    Liu, Wen; Zhang, Boyang; Fu, Lin

    2017-08-01

    The Roman curse tablet, produced in ancient Rome period, is a metal plate that inscribed with curses. In this research, several techniques were used to find out the physical structure and chemical composition of the Roman curse tablet, and testified the hypothesis that whether the tablet is made of pure lead or lead alloy. A sample of Roman Curse Tablet from the Johns Hopkins Archaeological Museum was analyzed using several different characterization techniques to determine the physical structure and chemical composition. The characterization techniques used were including optical microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). Because of the small sample size, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence (XRF) cannot test the sample. Results from optical microscopy and SEM, enlarged images of the sample surface were studied. The result revealed that the sample surface has a rough, non-uniform, and grainy surface. AFM provides three-dimensional topography of the sample surface, studying the sample surface in atomic level. DSC studies the thermal property, which is most likely a lead-alloy, not a pure lead. However, none of these tests indicated anything about the chemical composition. Future work will be required due to the lack of measures finding out its chemical composition. Therefore, from these characterization techniques above, the Roman curse tablet sample is consisted of lead alloy, not pure lead.

  17. Tablet Velocity Measurement and Prediction in the Pharmaceutical Film Coating Process.

    PubMed

    Suzuki, Yasuhiro; Yokohama, Chihiro; Minami, Hidemi; Terada, Katsuhide

    2016-01-01

    The purpose of this study was to measure the tablet velocity in pan coating machines during the film coating process in order to understand the impact of the batch size (laboratory to commercial scale), coating machine type (DRIACOATER, HICOATER® and AQUA COATER®) and manufacturing conditions on tablet velocity. We used a high speed camera and particle image velocimetry to measure the tablet velocity in the coating pans. It was observed that increasing batch sizes resulted in increased tablet velocities under the same rotation number because of the differences in circumferential rotation speeds. We also observed the tendency that increase in the filling ratio of tablets resulted in an increased tablet velocity for all coating machines. Statistical analysis was used to make a tablet velocity predictive equation by employing the filling ratio and rotation speed as the parameters from these measured values. The correlation coefficients of predicted value and experimental value were more than 0.959 in each machine. Using the predictive equation to determine tablet velocities, the manufacturing conditions of previous products were reviewed, and it was found that the tablet velocities of commercial scales, in which tablet chipping and breakage problems had occurred, were higher than those of pilot scales or laboratory scales.

  18. Placing wireless tablets in clinical settings for patient education.

    PubMed

    Stribling, Judy C; Richardson, Joshua E

    2016-04-01

    The authors explored the feasibility and possible benefit of tablet-based educational materials for patients in clinic waiting areas. We distributed eight tablets preloaded with diagnosis-relevant information in two clinic waiting areas. Patients were surveyed about satisfaction, usability, and effects on learning. Technical issues were resolved. Thirty-seven of forty patients completed the survey. On average, the patients were satisfied in all categories. Placing tablet-based educational materials in clinic waiting areas is relatively easy to implement. Patients using tablets reported satisfaction across three domains: usability, education, and satisfaction.

  19. Axial strength test for round flat faced versus capsule shaped bilayer tablets.

    PubMed

    Franck, Jason; Abebe, Admassu; Keluskar, Rekha; Martin, Kyle; Majumdar, Antara; Kottala, Niranjan; Stamato, Howard

    2015-03-01

    There has been increasing interest in fixed dose combination (FDC) therapy. Multi-layer tablets are a popular choice among various technologies to deliver FDCs. In most cases, round flat faced tooling is used in testing tablets as they have the simplest geometry. However, shaped tooling is more common for commercial products and may have an effect on bilayer tablet strength. Capsule shaped bilayer tablets, similar to a commercial image, and holders conforming to the tablet topology, were compared with similar round flat faced bilayer tablets and their corresponding holders. Bilayer tablets were subjected to an axial test device, until fracture and the quantitative breaking force value was recorded. As the second layer compression force increases, regardless of holder design, an increase in breaking force occurs as expected. This consistent trend provides insight regarding the breaking force of capsule shaped bilayer tablets. The results of this study show that at lower second layer compression forces, tablet geometry does not significantly impact the results. However, at higher compression forces, a significant difference in breaking force between tablet geometries exists. Therefore, using a test geometry close to the final commercial tablet image is recommended to have the most accurate prediction for tablet breakage.

  20. Formulation and characterization of cetylpyridinium chloride bioadhesive tablets.

    PubMed

    Akbari, Jafar; Saeedi, Majid; Morteza-Semnani, Katayoun; Kelidari, Hamidreza; Lashkari, Maryam

    2014-12-01

    Bioadhesive polymers play an important role in biomedical and drug delivery applications. The aim of this study is to develop a sustained- release tablet for local application of Cetylpyridinium Chloride (CPC). This delivery system would supply the drug at an effective level for a long period of time, and thereby overcome the problem of the short retention time of CPC and could be used for buccal delivery as a topical anti-infective agent. CPC bioadhesive tablets were directly prepared using 7 mm flat-faced punches on a hydraulic press. The materials for each tablet were weighted, introduced into the die and compacted at constant compression pressure. The dissolution tests were performed to the rotation paddle method and the bioadhesive strength of the tablets were measured. The results showed that as the concentration of polymer increased, the drug release rate was decreased. Also the type and ratio of polymers altered the release kinetic of Cetylpyridinium Chloride from investigated tablets. The bioadhesion strength increased with increasing the concentration of polymer and maximum bioadhesion strength was observed with HPMC K100M. The selected formulation of CPC bioadhesive tablet can be used as a suitable preparation for continuous release of CPC with appropriate bioadhesion strength.

  1. 21 CFR 520.2260c - Sulfamethazine sustained-release tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfamethazine sustained-release tablets. 520....2260c Sulfamethazine sustained-release tablets. (a) Sponsor. See No. 053501 in § 510.600(c) of this chapter for use of an 8-gram sulfamethazine sustained-release tablet. (b) Conditions of use—(1) Amount. 8...

  2. Bioequivalence of saxagliptin/dapagliflozin fixed-dose combination tablets compared with coadministration of the individual tablets to healthy subjects.

    PubMed

    Vakkalagadda, Blisse; Vetter, Marion L; Rana, Jignasa; Smith, Charles H; Huang, Jian; Karkas, Jennifer; Boulton, David W; LaCreta, Frank

    2015-12-01

    Saxagliptin and dapagliflozin are individually indicated as an adjunct to diet and exercise to improve glycemic control in adults with type 2 diabetes mellitus. The bioequivalence of saxagliptin/dapagliflozin 2.5/5 mg and 5/10 mg fixed-dose combination (FDC) tablets compared with coadministration of the individual tablets and the food effect on both strengths of saxagliptin/dapagliflozin FDCs were evaluated in this open-label, randomized, single-dose crossover study. Healthy subjects were randomized to saxagliptin 2.5 mg + dapagliflozin 5 mg fasted, 2.5/5 mg FDC fasted, 2.5/5 mg FDC fed (Cohort 1) or saxagliptin 5 mg + dapagliflozin 10 mg fasted, 5/10 mg FDC fasted, 5/10 mg FDC fed (Cohort 2). Serial blood samples for pharmacokinetics of saxagliptin and dapagliflozin were obtained predose and up to 60 h postdose. Bioequivalence of FDC tablets versus individual components was concluded if the 90% CIs for FDC to individual component geometric mean ratios of C max, AUC 0-T, and AUC inf of both analytes were between 0.80 and 1.25. Seventy-two subjects were randomized; 71 (98.6%) completed the study. Saxagliptin/dapagliflozin 2.5/5 mg and 5/10 mg FDC tablets were bioequivalent to the individual tablets administered concomitantly. Food had no clinically meaningful effect on saxagliptin or dapagliflozin overall systemic exposure. Saxagliptin/dapagliflozin FDC tablets were bioequivalent to coadministration of the individual components in healthy subjects under fasted conditions and food had no clinically meaningful effect on bioavailability.

  3. Replacing Smartphones With Mini Tablet Technology: An Evaluation.

    PubMed

    Maneval, Rhonda; Mechtel, Marci

    Handheld technology allows students to access point-of-care resources throughout the clinical experience. To assess the viability of replacing student smartphones with tablets, an evaluation project was undertaken. Overall, students were equally dissatisfied with the 2 types of tablets that were evaluated. Students saw the potential usefulness of tablets to manage clinical assignments, interact with the learning management system, and communicate with faculty, but not for retrieving information currently accessible on their phones.

  4. A fixed-dose combination tablet of gemigliptin and metformin sustained release has comparable pharmacodynamic, pharmacokinetic, and tolerability profiles to separate tablets in healthy subjects.

    PubMed

    Park, Sang-In; Lee, Howard; Oh, Jaeseong; Lim, Kyoung Soo; Jang, In-Jin; Kim, Jeong-Ae; Jung, Jong Hyuk; Yu, Kyung-Sang

    2015-01-01

    In type 2 diabetes mellitus, fixed-dose combination (FDC) can provide the complementary benefits of correction of multiple pathophysiologic defects such as dysfunctions in glycemic or metabolic control while improving compliance compared with separate tablets taken together. The objective of the study reported here was to compare the pharmacodynamic (PD), pharmacokinetic (PK), and tolerability profiles of gemigliptin and extended-release metformin (metformin XR) between FDC and separate tablets. A randomized, open-label, single-dose, two-way, two-period, crossover study was conducted in 28 healthy male volunteers. Two FDC tablets of gemigliptin/metformin 25/500 mg or separate tablets of gemigliptin (50 mg ×1) and metformin XR (500 mg ×2) were orally administered in each period. Serial blood samples were collected up to 48 hours post-dose to determine dipeptidyl peptidase 4 (DPP-4) activity using spectrophotometric assay and concentrations of gemigliptin and metformin using tandem mass spectrometry. Geometric mean ratios (GMRs) of FDC to separate tablet formulations and their 90% confidence intervals (CIs) were calculated to compare the PD and PK parameters between the two formulations. Tolerability was assessed throughout the study. The plasma DPP-4 activity-time curves of the FDC and the separate tablets almost overlapped, leading to a GMR (90% CI) of the FDC to separate tablets for the plasma DPP-4 activity and its maximum inhibition of 1.00 (0.97-1.04) and 0.92 (0.82-1.05), respectively. Likewise, all of the GMRs (90% CIs) of FDC to separate tablets for the area under the plasma concentration-time curve and maximum plasma concentration of gemigliptin and metformin fell entirely within the conventional bioequivalence range of 0.80-1.25. Both the FDC and separate tablets were well tolerated. The PD, PK, and tolerability profiles of gemigliptin and metformin XR in FDC and separate tablets were found to be comparable. The FDC tablet of gemigliptin and metformin

  5. Transforming the Classroom With Tablet Technology.

    PubMed

    Sargent, Lana; Miles, Elizabeth

    Identifying the most effective models for integrating new technology into the classroom and understanding its effects on educational outcomes are essential for nurse educators. This article describes an educational intervention with tablet technology (iPads) using an innovative case-based learning model in a nursing program. Students reported positive learning outcomes when using the tablet technology for learning course content.

  6. Enhanced oral bioavailability of felodipine by novel solid self-microemulsifying tablets.

    PubMed

    Jing, Boyu; Wang, Zhiyuan; Yang, Rui; Zheng, Xia; Zhao, Jia; Tang, Si; He, Zhonggui

    2016-01-01

    The novel self-microemulsifying (SME) tablets were developed to enhance the oral bioavailability of a poor water-soluble drug felodipine (FDP). Firstly, FDP was dissolved in the optimized liquid self-microemusifying drug delivery systems (SMEDDS) containing Miglyol® 812, Cremophor® RH 40, Tween 80 and Transcutol® P, and the mixture was solidified with porous silicon dioxide and crospovidone as adsorbents. Then after combining the solidified powders with other excipients, the solid SME tablets were prepared by wet granulation-compression method. The prepared tablets possessed satisfactory characterization; the droplet size of the SME tablets following self-emulsification in water was nearly equivalent to the liquid SMEDDS (68.4 ± 14.0 and 64.4 ± 12.0 nm); differential scanning calorimetry (DSC) and powder X-ray diffractometry (PXRD) analysis demonstrated that FDP in SME tablets had undergone a polymorphism transition from a crystal form to an amorphous state, which was further confirmed by transmission electron microscopy (TEM). A similar dissolution performance of SME tablets and liquid SMEDDS was also obtained under the sink condition (85% within 10 min), both significantly higher than commercial tablets. The oral bioavailability was evaluated for the SME tablets, liquid SMEDDS and commercial conventional tablets in the fasted beagle dogs. The AUC of FDP from the SME tablets was about 2-fold greater than that of conventional tablets, but no significant difference was found when compared with the liquid SMEDDS. Accordingly, these preliminary results suggest that this formulation approach offers a useful large-scale producing method to prepare the solid SME tablets from the liquid SMEDDS for oral bioavailability equivalent enhancement of poorly soluble FDP.

  7. Chewability testing in the development of a chewable tablet for hyperphosphatemia.

    PubMed

    Lanz, Michael; Baldischweiler, Jan; Kriwet, Burkhard; Schill, Jutta; Stafford, John; Imanidis, Georgios

    2014-12-01

    The official Pharmacopeia does not include a test procedure for the in vitro estimation of the chewability of tablets and publications in the scientific literature on this subject are rare. The purpose of this study was to evaluate a number of different test procedures for assessing chewability, starting from standard breaking force and strength testing and progressing to develop new procedures that simulate the actual chewing action on tablets. A further goal was to apply these test procedures to characterize the chewability of the novel phosphate binder PA21 in comparison with a commercially available phosphate binder chewable tablet product based on lanthanum (Fosrenol®) and a chewable tablet product containing calcium (Calcimagon®) - the latter being used as a standard for its very good chewability. For this purpose, a number of development formulations (different batches of PA21) were tested. The radial or diametrical tablet breaking force offers a poor means of assessing chewability while the axial breaking force was concluded to better reflect the effect of chewing on the tablet. Measurement of tablet behavior upon repeated loading afforded the best simulation of the actual chewing action and was found to have a good discriminating power with respect to chewability of the tested tablets, especially when the tablet was moistened with artificial saliva. The developed tests are shown to be more suitable for evaluating chewing properties of tablets than currently used Pharmacopeial tests. Following ICHQ6, which calls for specification of hardness for chewable tablets, these test procedures enabled the optimal chewability features of PA21 tablets in development to be confirmed whilst still maintaining capabilities for robust production and transportation processes.

  8. Fire behavior of e-tablets stored in aircraft galley carts.

    DOT National Transportation Integrated Search

    2015-04-01

    The use of electronic-tablets (e-tablets) as replacements for conventional in-flight entertainment systems has gained popularity : among airlines globally. Innovative methods of storing and charging e-tablets in galley carts have been suggested or ar...

  9. Formulation and evaluation of non-effervescent floating tablets of losartan potassium.

    PubMed

    Getyala, Anil; Gangadharappa, H V; Prasad, M Sarat Chandra; Reddy, M Praveen Kumar; Kumar, T M Pramod

    2013-10-01

    The aim of the work is to modify the solubility and bioavailability of Losartan potassium, by employing noneffervescent floating drug delivery (tablet dosage forms). Non-effervescent systems are a type of floating drug delivery systems, that have been used to boost the gastric residence and the floatation time in the gastro intestinal tract. The study included formulation of floating tablets using polymers like Chitosan and Karaya gum as matrix forming agents. Accurel(®) MP 1000 was used as floating agent. The tablets were prepared by direct compression technique. FTIR, DSC studies conformed that there was no incompatibility between the polymer and the drug. Tablet preformulation parameters were within the Pharmacopoeial limit. Tablet showed zero lag time, contisnuance of buoyancy for >12 h. The tablet showed good in vitro release. Drug release was through swelling and abided by the gellation mechanism. In vivo X-ray studies depicted that tablets continued to float in the GIT for 12 h. Accelerated stability showed that, tablets were stable for over 6 month. Thus the prepared non-effervescent floating tablet of Losartan potassium can be used for the treatment of hypertension for more than 12 h with single dose administration.

  10. 21 CFR 520.2345g - Tetracycline hydrochloride and sodium novobiocin tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... tablets. 520.2345g Section 520.2345g Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... § 520.2345g Tetracycline hydrochloride and sodium novobiocin tablets. (a) Specifications. Each tablet... antibiotic per pound of body weight (one single-strength tablet for each 6 pounds or one triple-strength...

  11. Comparative stability of repackaged metoprolol tartrate tablets.

    PubMed

    Yang, Yongsheng; Gupta, Abhay; Carlin, Alan S; Faustino, Patrick J; Lyon, Robbe C; Ellison, Christopher D; Rothman, Barry; Khan, Mansoor A

    2010-01-29

    The stability of metoprolol tartrate tablets packaged in original high density polyethylene containers and repackaged in USP Class A unit-dose blister packs was investigated. Studies were conducted at 25 degrees C/60% relative humidity (RH) for 52 weeks and at 40 degrees C/75% RH for 13 weeks. The potency, dissolution, water content, loss on drying and hardness of the drug products were analyzed. Results indicated no differences in the stability between the tablets in both packages stored under 25 degrees C/60% RH. No difference in potency was found in both packages under either condition. However, a significant weight increase due to moisture uptake was observed for the repackaged tablets stored under 40 degrees C/75% RH. The weight increase was accompanied by a decrease in tablet hardness (6.5-0 kp) and a increase in dissolution rate (51-92%) in 5 min. Near-infrared (NIR) chemical imaging also monitored moisture uptake of the tablet non-invasively through the package. The observed changes in product stability may adversely affect the products bioavailability profile, even though the potency of the active drug remained within USP specification range of 90-110%. Study results suggest product quality can be negatively impacted even when using USP Class A repackaging materials. Published by Elsevier B.V.

  12. Tablet potency of Tianeptine in coated tablets by near infrared spectroscopy: model optimisation, calibration transfer and confidence intervals.

    PubMed

    Boiret, Mathieu; Meunier, Loïc; Ginot, Yves-Michel

    2011-02-20

    A near infrared (NIR) method was developed for determination of tablet potency of active pharmaceutical ingredient (API) in a complex coated tablet matrix. The calibration set contained samples from laboratory and production scale batches. The reference values were obtained by high performance liquid chromatography (HPLC) and partial least squares (PLS) regression was used to establish a model. The model was challenged by calculating tablet potency of two external test sets. Root mean square errors of prediction were respectively equal to 2.0% and 2.7%. To use this model with a second spectrometer from the production field, a calibration transfer method called piecewise direct standardisation (PDS) was used. After the transfer, the root mean square error of prediction of the first test set was 2.4% compared to 4.0% without transferring the spectra. A statistical technique using bootstrap of PLS residuals was used to estimate confidence intervals of tablet potency calculations. This method requires an optimised PLS model, selection of the bootstrap number and determination of the risk. In the case of a chemical analysis, the tablet potency value will be included within the confidence interval calculated by the bootstrap method. An easy to use graphical interface was developed to easily determine if the predictions, surrounded by minimum and maximum values, are within the specifications defined by the regulatory organisation. Copyright © 2010 Elsevier B.V. All rights reserved.

  13. Quality-by-design approach for the development of telmisartan potassium tablets.

    PubMed

    Oh, Ga-Hui; Park, Jin-Hyun; Shin, Hye-Won; Kim, Joo-Eun; Park, Young-Joon

    2018-05-01

    A quality-by-design approach was adopted to develop telmisartan potassium (TP) tablets, which were bioequivalent with the commercially available Micardis ® (telmisartan free base) tablets. The dissolution pattern and impurity profile of TP tablets differed from those of Micardis ® tablets because telmisartan free base is poorly soluble in water. After identifying the quality target product profile and critical quality attributes (CQAs), drug dissolution, and impurities were predicted to be risky CQAs. To determine the exact range and cause of risks, we used the risk assessment (RA) tools, preliminary hazard analysis and failure mode and effect analysis to determine the parameters affecting drug dissolution, impurities, and formulation. The range of the design space was optimized using the face-centered central composite design among the design of experiment (DOE) methods. The binder, disintegrant, and kneading time in the wet granulation were identified as X values affecting Y values (disintegration, hardness, friability, dissolution, and impurities). After determining the design space with the desired Y values, the TP tablets were formulated and their dissolution pattern was compared with that of the reference tablet. The selected TP tablet formulated using design space showed a similar dissolution to that of Micardis ® tablets at pH 7.5. The QbD approach TP tablet was bioequivalent to Micardis ® tablets in beagle dogs.

  14. Characterising the disintegration properties of tablets in opaque media using texture analysis.

    PubMed

    Scheuerle, Rebekah L; Gerrard, Stephen E; Kendall, Richard A; Tuleu, Catherine; Slater, Nigel K H; Mahbubani, Krishnaa T

    2015-01-01

    Tablet disintegration characterisation is used in pharmaceutical research, development, and quality control. Standard methods used to characterise tablet disintegration are often dependent on visual observation in measurement of disintegration times. This presents a challenge for disintegration studies of tablets in opaque, physiologically relevant media that could be useful for tablet formulation optimisation. This study has explored an application of texture analysis disintegration testing, a non-visual, quantitative means of determining tablet disintegration end point, by analysing the disintegration behaviour of two tablet formulations in opaque media. In this study, the disintegration behaviour of one tablet formulation manufactured in-house, and Sybedia Flashtab placebo tablets in water, bovine, and human milk were characterised. A novel method is presented to characterise the disintegration process and to quantify the disintegration end points of the tablets in various media using load data generated by a texture analyser probe. The disintegration times in the different media were found to be statistically different (P<0.0001) from one another for both tablet formulations using one-way ANOVA. Using the Tukey post-hoc test, the Sybedia Flashtab placebo tablets were found not to have statistically significant disintegration times from each other in human versus bovine milk (adjusted P value 0.1685). Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Developing a mapping tool for tablets

    NASA Astrophysics Data System (ADS)

    Vaughan, Alan; Collins, Nathan; Krus, Mike

    2014-05-01

    Digital field mapping offers significant benefits when compared with traditional paper mapping techniques in that it provides closer integration with downstream geological modelling and analysis. It also provides the mapper with the ability to rapidly integrate new data with existing databases without the potential degradation caused by repeated manual transcription of numeric, graphical and meta-data. In order to achieve these benefits, a number of PC-based digital mapping tools are available which have been developed for specific communities, eg the BGS•SIGMA project, Midland Valley's FieldMove®, and a range of solutions based on ArcGIS® software, which can be combined with either traditional or digital orientation and data collection tools. However, with the now widespread availability of inexpensive tablets and smart phones, a user led demand for a fully integrated tablet mapping tool has arisen. This poster describes the development of a tablet-based mapping environment specifically designed for geologists. The challenge was to deliver a system that would feel sufficiently close to the flexibility of paper-based geological mapping while being implemented on a consumer communication and entertainment device. The first release of a tablet-based geological mapping system from this project is illustrated and will be shown as implemented on an iPad during the poster session. Midland Valley is pioneering tablet-based mapping and, along with its industrial and academic partners, will be using the application in field based projects throughout this year and will be integrating feedback in further developments of this technology.

  16. Safety and tolerability of cladribine tablets in multiple sclerosis: the CLARITY (CLAdRIbine Tablets treating multiple sclerosis orallY) study.

    PubMed

    Cook, S; Vermersch, P; Comi, G; Giovannoni, G; Rammohan, K; Rieckmann, P; Sørensen, P Soelberg; Hamlett, A; Miret, M; Weiner, J; Viglietta, V; Musch, B; Greenberg, S J

    2011-05-01

    Cladribine is a synthetic deoxyadenosine analogue in development as an oral multiple sclerosis (MS) therapy. To report in detail the safety findings from the 96-week, phase III, double-blind CLARITY study, which evaluated treatment with cladribine tablets in relapsing-remitting MS. A total of 1,326 patients were randomized 1:1:1 to two short-course regimens of cladribine tablets (3.5 or 5.25 mg/kg cumulative dose over 96 weeks) or placebo. Safety assessments included monitoring for adverse events (AEs), routine physical and neurologic examinations and frequent laboratory parameter assessments. Of the randomized patients, 88.6% completed treatment with cladribine tablets versus 86.3% with placebo. Lymphopenia was the most commonly reported AE in patients treated with cladribine tablets and was anticipated based on the mechanism of action. The incidence of infections was 48.3% with cladribine tablets and 42.5% with placebo, with 99.1% and 99.0% rated mild-to-moderate by investigators. Herpes zoster infections developed in 20 (2.3%) cladribine-treated patients; all cases were dermatomal. There were no herpes zoster infections in the placebo group. Nine (1.0%) patients experienced events related to uterine leiomyomas in the cladribine tablets groups versus one (0.2%) with placebo. Three isolated cases of malignancy were reported in cladribine-treated patients during the study; a fourth was reported during post-study surveillance. A pre-malignant cervical carcinoma in situ was also reported. The incidence of malignancies during the study did not exceed the expected rate in a population standardized for country, gender and age. The safety and tolerability profile observed in the CLARITY study together with the reported efficacy support the potential for cladribine tablets as an MS therapy.

  17. Formulation and evaluation of dried yeast tablets using different techniques.

    PubMed

    Al-Mohizea, Abdullah M; Ahmed, Mahrous O; Al-jenoobi, Fahad I; Mahrous, Gamal M; Abdel-Rahman, Aly A

    2007-08-01

    The aim of this study was to prepare and evaluate dried yeast tablets using both direct compression and dry granulation techniques in comparison with the conventional wet granulation as well as commercial product. Wet granulation technique is not favorable for producing the yeast tablets due to the problems of color darkening and the reduction of the fermentation power of the yeast as a result of the early start of the fermentation process due to the presence of moisture. Twenty six formulae of dried yeast tablets were prepared and evaluated. Certain directly compressible vehicles were employed for preparing these tablets. The quality control tests (weight uniformity, friability, disintegration time and hardness) of the prepared dried yeast tablets were performed according to B.P. 1998 limits. All batches of the prepared tablets complied with the B.P. limits of weight uniformity. Moreover, small values of friability % (1% or less) were obtained for all batches of dried yeast tablets with acceptable hardness values, indicating good mechanical properties which can withstand handling. On the other hand, not all batches complied with the limit of disintegration test which may be attributed to various formulation component variables. Therefore, four disintegrating agents were investigated for their disintegrating effect. It was found that the method of preparation, whether it is direct compression, dry granulation or wet granulation, has an effect on disintegration time of these dried yeast tablets and short disintegration times were obtained for some of the formulae. The shortest disintegration time was obtained with those tablets prepared by direct compression among the other techniques. Therefore, the direct compression is considered the best technique for preparation of dried yeast tablets and the best formula (which showed shorter disintegration time and better organoleptic properties than the available commercial yeast tablets) was chosen. Drug content for dried

  18. Usability of tablet computers by people with early-stage dementia.

    PubMed

    Lim, Fabian S; Wallace, Tim; Luszcz, Mary A; Reynolds, Karen J

    2013-01-01

    Tablet computers are generally associated with an intuitive interface. The adoption and use of tablet computers within the early-stage dementia context could potentially assist in daily living and provide users with a source for leisure activities and social networking. As dementia mainly affects the older adult population, it is expected that many people with dementia and even their carers do not use tablet computers as part of their everyday living. This paper explores the usability of tablet computers within the early-stage dementia context as a source of leisure for people with dementia. The main advantage of the use of tablet computers in this manner is to provide carers some reprieve from the constant care and attention often required in caring for people with dementia. Seven-day in-home trials were conducted to determine whether people with early-stage dementia were -capable of using a tablet computer independently. Twenty-one people with early-stage dementia and carer dyads participated in the trial. Feedback was gathered through questionnaires from both the person with dementia and their carer regarding the use of a tablet computer as part of their everyday living. Approximately half the participants with dementia were able to engage with and use the tablet computer independently, which proved to be helpful to their carers. No significant traits were observed to help identify those who were less likely to use a tablet computer. Carer relief was quantified by the amount of time participants with dementia spent using the device without supervision. The results and feedback from the trial provide significant insights to introducing new technology within the early-stage dementia context. Users' needs must be considered on a case-by-case basis to successfully facilitate the uptake of tablet computers in the dementia context. The trial has provided sufficient justification to further explore more uses of tablet computers in the dementia context, and not just for

  19. Quantification of color vision using a tablet display.

    PubMed

    Chacon, Alicia; Rabin, Jeff; Yu, Dennis; Johnston, Shawn; Bradshaw, Timothy

    2015-01-01

    Accurate color vision is essential for optimal performance in aviation and space environments using nonredundant color coding to convey critical information. Most color tests detect color vision deficiency (CVD) but fail to diagnose type or severity of CVD, which are important to link performance to occupational demands. The computer-based Cone Contrast Test (CCT) diagnoses type and severity of CVD. It is displayed on a netbook computer for clinical application, but a more portable version may prove useful for deployments, space and aviation cockpits, as well as accident and sports medicine settings. Our purpose was to determine if the CCT can be conducted on a tablet display (Windows 8, Microsoft, Seattle, WA) using touch-screen response input. The CCT presents colored letters visible only to red (R), green (G), and blue (B) sensitive retinal cones to determine the lowest R, G, and B cone contrast visible to the observer. The CCT was measured in 16 color vision normals (CVN) and 16 CVDs using the standard netbook computer and a Windows 8 tablet display calibrated to produce equal color contrasts. Both displays showed 100% specificity for confirming CVN and 100% sensitivity for detecting CVD. In CVNs there was no difference between scores on netbook vs. tablet displays. G cone CVDs showed slightly lower G cone CCT scores on the tablet. CVD can be diagnosed with a tablet display. Ease-of-use, portability, and complete computer capabilities make tablets ideal for multiple settings, including aviation, space, military deployments, accidents and rescue missions, and sports vision. Chacon A, Rabin J, Yu D, Johnston S, Bradshaw T. Quantification of color vision using a tablet display.

  20. Active Reading Behaviors in Tablet-Based Learning

    ERIC Educational Resources Information Center

    Palilonis, Jennifer; Bolchini, Davide

    2015-01-01

    Active reading is fundamental to learning. However, there is little understanding about whether traditional active reading frameworks sufficiently characterize how learners study multimedia tablet textbooks. This paper explores the nature of active reading in the tablet environment through a qualitative study that engaged 30 students in an active…

  1. Mechanism by Which Magnesium Oxide Suppresses Tablet Hardness Reduction during Storage.

    PubMed

    Sakamoto, Takatoshi; Kachi, Shigeto; Nakamura, Shohei; Miki, Shinsuke; Kitajima, Hideaki; Yuasa, Hiroshi

    2016-01-01

    This study investigated how the inclusion of magnesium oxide (MgO) maintained tablet hardness during storage in an unpackaged state. Tablets were prepared with a range of MgO levels and stored at 40°C with 75% relative humidity for up to 14 d. The hardness of tablets prepared without MgO decreased over time. The amount of added MgO was positively associated with tablet hardness and mass from an early stage during storage. Investigation of the water sorption properties of the tablet components showed that carmellose water sorption correlated positively with the relative humidity, while MgO absorbed and retained moisture, even when the relative humidity was reduced. In tablets prepared using only MgO, a petal- or plate-like material was observed during storage. Fourier transform infrared spectrophotometry showed that this material was hydromagnesite, produced when MgO reacts with water and CO2. The estimated level of hydromagnesite at each time-point showed a significant negative correlation with tablet porosity. These results suggested that MgO suppressed storage-associated softening by absorbing moisture from the environment. The conversion of MgO to hydromagnesite results in solid bridge formation between the powder particles comprising the tablets, suppressing the storage-related increase in volume and increasing tablet hardness.

  2. Ginger Orally Disintegrating Tablets to Improve Swallowing in Older People.

    PubMed

    Hirata, Ayumu; Funato, Hiroki; Nakai, Megumi; Iizuka, Michiro; Abe, Noriaki; Yagi, Yusuke; Shiraishi, Hisashi; Jobu, Kohei; Yokota, Junko; Hirose, Kahori; Hyodo, Masamitsu; Miyamura, Mitsuhiko

    2016-01-01

    We previously prepared and pharmaceutically evaluated ginger orally disintegrating (OD) tablets, optimized the base formulation, and carried out a clinical trial in healthy adults in their 20 s and 50s to measure their effect on salivary substance P (SP) level and improved swallowing function. In this study, we conducted clinical trials using the ginger OD tablets in older people to clinically evaluate the improvements in swallowing function resulting from the functional components of the tablet. The ginger OD tablets were prepared by mixing the excipients with the same amount of mannitol and sucrose to a concentration of 1% ginger. Eighteen healthy older adult volunteers aged 63 to 90 were included in the swallowing function test. Saliva was collected before and 15 min after administration of the placebo and ginger OD tablets. Swallowing endoscopy was performed by an otolaryngologist before administration and 15 min after administration of the ginger OD tablets. A scoring method was used to evaluate the endoscopic swallowing. Fifteen minutes after taking the ginger OD tablets, the salivary SP amount was significantly higher than prior to ingestion or after taking the placebo (p<0.05). Among 10 subjects, one scored 1-3 using the four evaluation criteria. Overall, no aspiration occurred and a significant improvement in the swallowing function score was observed (p<0.05) after taking the ginger OD tablets. Our findings showed that the ginger OD tablets increased the salivary SP amount and improved swallowing function in older people with appreciably reduced swallowing function.

  3. Dissolution Studies of Papaverine Hydrochloride from Tablets in Three Pharmacopoeia Apparatuses.

    PubMed

    Polski, Andrzej; Kasperek, Regina; Rogowska, Magdalena; Iwaniak, Karol; Sobòtka-Polska, Karolina; Poleszak, Ewa

    2015-01-01

    In tablet production, the most important aspects are the physical properties of the tablets and their dissolution studies, which can be performed in four pharmacopoeial apparatuses. There are differences between them in construction and action, so differences in the results obtained are possible. The aim of the study was to compare the release of a model drug substance (papaverine hydrochloride) from tablets in three pharmacopoeial dissolution apparatus: a basket, a paddle (closed system) and flow-through cell (open system). The one series of tablets were produced by direct compression in a tablet press. The physical properties of the tablets (weight and size uniformity test, friability and hardness tests, disintegration time test), drug content and the release study of papaverine hydrochloride from tablets were studied in three dissolution apparatuses. The content of the active substance was studied spectrophotometrically. All tablets met the pharmacopoeic requirements. Over 80% of the model substance released from the tablets after 14 min in flow through the cell apparatus, while in the basket and paddle apparatuses after about 7 min 30 sec. After 20 min, the amount of the substance released in all apparatuses was over 90%. The release profiles of the drug substance in paddle and basket apparatuses were similar, while in the flow-through cell apparatus it was slightly slower. When the study conditions and composition of the tablets are the same, the release profile of the drug can be affected by the type of dissolution apparatus.

  4. Exposures to traditional automatic dishwashing tablets and a comparison with exposures to soluble film tablets reported to the United Kingdom National Poisons Information Service 2008-2015.

    PubMed

    Day, Rachael; Eddleston, Michael; Thomas, Simon H L; Thompson, John P; Vale, J Allister

    2017-03-01

    Traditional automatic dishwashing tablets are contained within an external wrapper that requires removal prior to use. To determine the toxicity of traditional tablets and to compare this with our previously reported experience of soluble film dishwashing tablets. Telephone enquiries regarding traditional tablets were analysed retrospectively for the period January 2008 to December 2015. Traditional tablets: There were 503 enquiries relating to 492 patients who had been exposed to a traditional tablet. Most involved children aged 5 years or less (87.4%). The majority (78.6%) of patients did not develop symptoms after exposure; 21.1% developed minor (PSS 1) symptoms while one patient developed moderate features. Exposure occurred predominantly as a result of ingestion (n = 476, 96.7%); the most common feature in symptomatic patients (n = 99, 20.8%) was vomiting (70 [14.7%] cases). Significantly (p < 0.0001) more adults (44.9% of 49 adults; 95% CI = 31.9-58.7) were reported with features than children (18.2% of 434; 95% CI = 14.9-22.1). There were five cases of eye contact which resulted in eye pain in two patients and eye irritation in another. Only one of 11 patients exposed dermally developed features (a rash around the mouth). Comparison with soluble film exposures: The percentage of patients that were reported with clinical symptoms following ingestion of a soluble film dishwashing tablet (31.7% of 473 patients; 95% CI = 27.7-36.0) was significantly greater (p < 0.0001) than that for a traditional tablet (20.9% of 483 patients; 95% CI = 17.5-24.8). Vomiting was the most commonly reported feature and occurred significantly (p < 0.0001) more frequently amongst patients who had ingested a soluble film tablet (25.5%; 95% CI = 21.8-29.6) than a traditional tablet (14.7%; 95% CI = 11.8-18.1). Exposure to both traditional and soluble film tablets only rarely produced clinically significant symptoms (PSS ≥2). However

  5. 21 CFR 520.1872 - Praziquantel, pyrantel pamoate, and febantel tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS... food as follows: Weight of animal Kilograms Pounds Number of tablets per dose Tablet no. 1 Tablet no. 2... tapeworms (Dipylidium caninum, Taenia pisiformis, Echinococcus granulosus); hookworms (Ancylostoma caninum...

  6. 21 CFR 520.1872 - Praziquantel, pyrantel pamoate, and febantel tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS... food as follows: Weight of animal Kilograms Pounds Number of tablets per dose Tablet no. 1 Tablet no. 2... tapeworms (Dipylidium caninum, Taenia pisiformis, Echinococcus granulosus); hookworms (Ancylostoma caninum...

  7. 21 CFR 520.1872 - Praziquantel, pyrantel pamoate, and febantel tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS... food as follows: Weight of animal Kilograms Pounds Number of tablets per dose Tablet no. 1 Tablet no. 2... tapeworms (Dipylidium caninum, Taenia pisiformis, Echinococcus granulosus); hookworms (Ancylostoma caninum...

  8. 21 CFR 520.1872 - Praziquantel, pyrantel pamoate, and febantel tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS... food as follows: Weight of animal Kilograms Pounds Number of tablets per dose Tablet no. 1 Tablet no. 2... tapeworms (Dipylidium caninum, Taenia pisiformis, Echinococcus granulosus); hookworms (Ancylostoma caninum...

  9. Absorption from iron tablets given with different types of meals.

    PubMed

    Hallberg, L; Björn-Rasmussen, E; Ekenved, G; Garby, L; Rossander, L; Pleehachinda, R; Suwanik, R; Arvidsson, B

    1978-09-01

    The absorption of iron from tablets given with 5 types of meals was studied in 153 subjects. The meals were: a hamburger meal with beans and potatoes, a simple breakfast meal, a Latin American meal composed of black beans, rice and maize and two Southeast Asian meals composed of rice, vegetables and spices served with and without fish. The groups were directly compared by relating the absorption from the iron tablets to the absorption from a standardized reference dose of iron given on an empty stomach. The composition of meals with respect to content of meat or fish or the presence of large amounts of phytates seemed to have no influence on the absorption of iron from tablets. The absorption from iron tablets was about 40% higher when they were given with rice meals than when they were given with the other meals studied. The average decrease in absorption by meals was about 50-60% based on a comparison when tablets were given on an empty stomach. When tablets from which the iron was released more slowly were used, the absorption increased by about 30% except when they were given with rice meals, where the absorption was unchanged. The differences among the meals in their effect on the absorption of iron from tablets thus disappeared when the slow-release tablets were given.

  10. The Preparation of Capsaicin-Chitosan Microspheres (CCMS) Enteric Coated Tablets

    PubMed Central

    Chen, Jian; Huang, Gui-Dong; Tan, Si-Rong; Guo, Jiao; Su, Zheng-Quan

    2013-01-01

    This study aimed to research the preparation and content determination of capsaicin-chitosan microspheres (CCMS) enteric coated tablets. The core tablets were prepared with the method of wet granulation. Nine formulae were designed to determine the optimal formula of the core tablet. Eudragit L100 was used to prepare the CCMS enteric-coated tablets. The effect of enteric coated formulation variables such as content of talc (10%, 25% and 40%), plasticisers (TEC and DBS), dosage of plasticiser (10%, 20% and 30%) and coating weight (2%, 3% and 5%) were evaluated for drug release characteristics. The in vitro release was studied using 0.1 N HCl and pH 6.8 phosphate buffer. Enteric coated tablets without ruptures or swelling behaviour over 2 h in 0.1 N HCl indicated that these tablets showed acid resistance. The accumulated release rate in phosphate buffer (pH 6.8) revealed that the prepared tablets were able to sustain drug release into the intestine and a first-order release was obtained for capsaicin. This research is the first report of the preparation and content determination of CCMS enteric coated tablets. The sustained release behavior of enteric coated formulations in pH 6.8 phosphate buffer demonstrated that it would be a potential drug delivery platform for sustained delivery of gastric irritant drugs. PMID:24351818

  11. Comparative evaluation of single and bilayered lamotrigine floating tablets

    PubMed Central

    Lakshmi, PK; Sridhar, M; Shruthi, B

    2013-01-01

    Aim: The purpose of this study was to prepare lamotrigine (LM) bilayered and single layered floating tablets and to compare their release profiles. Materials and Methods: LM floating tablets were prepared by direct compression method. Drug, hydroxy propyl methyl cellulose K4M, lactose monohydrate and polyvinylpyrrolidone K30 constitute controlled release layer components and floating layer components includes polymers and sodium bicarbonate. The prepared tablets were evaluated for physicochemical parameters such as hardness, friability, weight variation, thickness, floating lag time (FLT), floating time, in vitro buoyancy study, in vitro release studies. The drug-polymer interaction was studied by fourier transform infrared and differential scanning calorimetry. Results and Discussion: The FLT of all the formulations were within the prescribed limits (<3 min). When ethyl cellulose was used as floating layer component, tablets showed good buoyancy effect but eroded within 6-8 h. Hence it was replaced with hydroxypropyl cellulose -M hydrophilic polymer, which showed good FLT and floating duration for 16 h. Formulation LFC4 was found to be optimized with dissolution profile of zero order kinetics showing fickian diffusion. A comparative study of bilayered and single layered tablets of LM showed a highest similarity factor of 83.03, difference factor of 2.74 and t-test (P < 0.05) indicates that there is no significant difference between them. Conclusion: Though bilayered tablet possess many advantages, single layered tablet would be economical, cost-effective and reproducible for large scale production in the industry. However, the results of present study demonstrated that the in vitro development of bilayered gastro retentive floating tablets with controlled drug release profile for LM is feasible. PMID:24167788

  12. Ultrasound transmission measurements for tensile strength evaluation of tablets.

    PubMed

    Simonaho, Simo-Pekka; Takala, T Aleksi; Kuosmanen, Marko; Ketolainen, Jarkko

    2011-05-16

    Ultrasound transmission measurements were performed to evaluate the tensile strength of tablets. Tablets consisting of one ingredient were compressed from dibasic calcium phosphate dehydrate, two grades of microcrystalline cellulose and two grades of lactose monohydrate powders. From each powder, tablets with five different tensile strengths were directly compressed. Ultrasound transmission measurements were conducted on every tablet at frequencies of 2.25 MHz, 5 MHz and 10 MHz and the speed of sound was calculated from the acquired waveforms. The tensile strength of the tablets was determined using a diametrical mechanical testing machine and compared to the calculated speed of sound values. It was found that the speed of sound increased with the tensile strength for the tested excipients. There was a good correlation between the speed of sound and tensile strength. Moreover, based on the statistical tests, the groups with different tensile strengths can be differentiated from each other by measuring the speed of sound. Thus, the ultrasound transmission measurement technique is a potentially useful method for non-destructive and fast evaluation of the tensile strength of tablets. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Evaluation of cellulose II powders as a potential multifunctional excipient in tablet formulations.

    PubMed

    de la Luz Reus Medina, Maria; Kumar, Vijay

    2006-09-28

    The use of UICEL-A/102 and UICEL-XL, the cellulose II powders, as a multifunctional direct compression excipient in the design of tablets containing hydrochlorothiazide (HCTZ) or ibuprofen (IBU), the model low and high dose drugs, respectively, has been reported. Commercial Oretic and Advil tablets containing HCTZ and IBU, respectively, and tablets made using Avicel PH-102 - the most commonly and widely used commercial direct compression excipient, were used in the study for comparison purposes. Tablets were made by first blending drug with the excipient and then with stearic acid, a lubricant, in a V-blender, followed by compressing into a tablet on a hydraulic press using 105 MPa of compression pressure and a dwell time of 30 s. The crushing strengths of HCTZ tablets decreased in the order Avicel PH-102>UICEL-XL, UICEL-A/102>Oretic and of IBU tablets in the order Avicel PH-102 > or = UICEL-XL approximately UICEL-A/102>Advil. The friability values for all tablets were well below the maximum 1% USP tolerance limit. UICEL-A/102 and UICEL-XL tablets containing HCTZ disintegrated rapidly (<25 s). Oretic tablets disintegrated in about 60 s, while Avicel PH-102 tablets remained intact during 1 h test period. The IBU tablets made using UICEL-A/102 disintegrated the fastest, UICEL-XL and Advil tablets the next, and Avicel PH-102 tablets remained intact. All tablets, except for those of Avicel PH-102, conformed to the USP drug release requirements. These results conclusively show that UICEL-A/102 and UICEL-XL have the potential to be used as filler, binder, and disintegrant, all-in-one, in the design of tablets containing either a low dose or high dose drug by the direct compression method.

  14. Fertilizer Tablets Stimulate Eucalyptus in Florida Trial

    Treesearch

    George Meskimen

    1971-01-01

    Eucalyptus plantings in south Florida must grow rapidly to withstand first-year frosts and dominate herbaceous competition. Fertilizer tablets in the planting holes of E. camaldulensis stimulated immediate growth, resulting in stems 50 percent taller and 83 percent thicker than check trees at 6 months. Effects of tablets persisted after 4 years, with...

  15. Bioavailability of everolimus administered as a single 5 mg tablet versus five 1 mg tablets: a randomized, open-label, two-way crossover study of healthy volunteers.

    PubMed

    Thudium, Karen; Gallo, Jorge; Bouillaud, Emmanuel; Sachs, Carolin; Eddy, Simantini; Cheung, Wing

    2015-01-01

    The mammalian target of rapamycin (mTOR) inhibitor everolimus has a well-established pharmacokinetics profile. We conducted a randomized, single-center, open-label, two-sequence, two-period crossover study of healthy volunteers to assess the relative bioavailability of everolimus administered as one 5 mg tablet or five 1 mg tablets. Subjects were randomized 1:1 to receive everolimus dosed as one 5 mg tablet or as five 1 mg tablets on day 1, followed by a washout period on days 8-14 and then the opposite formulation on day 15. Blood sampling for pharmacokinetic evaluation was performed at prespecified time points, with 17 samples taken for each treatment period. Primary variables for evaluation of relative bioavailability were area under the concentration-time curve from time zero to infinity (AUCinf) and maximum blood concentration (Cmax). Safety was assessed by reporting the incidence of adverse events (AEs). Twenty-two participants received everolimus as one 5 mg tablet followed by five 1 mg tablets (n=11) or the opposite sequence (n=11). The Cmax of five 1 mg tablets was 48% higher than that of one 5 mg tablet (geometric mean ratio, 1.48; 90% confidence interval [CI], 1.35-1.62). AUCinf was similar (geometric mean ratio, 1.08; 90% CI, 1.02-1.16), as were the extent of absorption and the distribution and elimination kinetics. AEs, all grade 1 or 2, were observed in 54.5% of subjects. Although the extent of absorption was similar, the Cmax of five 1 mg tablets was higher than that of one 5 mg tablet, suggesting these formulations lead to different peak blood concentrations and are not interchangeable at the dose tested.

  16. 21 CFR 520.1196 - Ivermectin and pyrantel pamoate chewable tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ivermectin and pyrantel pamoate chewable tablets. 520.1196 Section 520.1196 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Ivermectin and pyrantel pamoate chewable tablets. (a) Specifications. Each chewable tablet contains either 68...

  17. 21 CFR 520.88a - Amoxicillin trihydrate film-coated tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Amoxicillin trihydrate film-coated tablets. 520.88a Section 520.88a Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Amoxicillin trihydrate film-coated tablets. (a) Specifications. Each tablet contains amoxicillin trihydrate...

  18. Exploration of the associations of touch-screen tablet computer usage and musculoskeletal discomfort.

    PubMed

    Chiang, Hsin-Yu Ariel; Liu, Chien-Hsiou

    2016-03-10

    Tablet users may be at high risk of developing physical discomfort because of their usage behaviors and tablet design. Investigate the usage of tablets, variations in head and neck posture associated with different tablet tilt angles, and the association of tablet use with users' musculoskeletal discomfort. A survey of users' subjective perceptions conducted by questionnaire and measurements of users' postures by a 3D Motion analysis system was used to explore the effects of tablet use. The questionnaire results indicated that over half of the participants reported physical discomfort after using tablets, with the most prevalent discomfort in the neck and shoulders, and more intensity of discomfort for the back although only few participants experienced it. Chi-squared tests indicated that significantly more participants who tended to use tablet computers to play games reported having musculoskeletal discomfort after using a tablet. In addition, preferences for tablet tilt angles varied across tasks (reading and game playing). The results from the 3D motion analysis revealed that head and neck flexion angles were significantly reduced when the tablets were positioned at relatively steep tilt angles. Neck flexion angle was significantly higher in game playing. These data add information regarding to the usage of tablet and its associations with physical discomfort (significantly more participants who tended to use tablet computers to play games reported having musculoskeletal discomfort after using a tablet). Steep tilt angles (such as 60°) may cause tablet users to decrease their head and neck flexion angles, which could lead to a more neutral, effortless, and ergonomically correct posture. Maintaining proper neck posture during active activities such as game playing is recommended to avoid neck discomfort.

  19. Variability in the 3,4-methylenedioxymethamphetamine content of 'ecstasy' tablets in the UK.

    PubMed

    Wood, David Michael; Stribley, Vasoulla; Dargan, Paul Ivor; Davies, Susannah; Holt, David W; Ramsey, John

    2011-09-01

    Toxicity, such as hyperpyrexia, associated with the use of 3,4-methylenedioxymethamphetamine (MDMA; 'ecstasy') appears to be related to serum MDMA concentrations. However, there does not appear to be a similar association with the number of tablets ingested, suggesting variation in the tablet content of MDMA. Although work has shown this variation in other areas of the world, no studies have reported on the variation of MDMA content in UK ecstasy tablets. Ecstasy tablets seized from individuals attending nightclubs were analysed qualitatively to determine if they contained MDMA and quantitatively to determine the MDMA content per tablet. The mean amount of MDMA hydrochloride in 101 seized ecstasy tablets was 58.7±22.9 mg per tablet, with a range of 20 mg to 131 mg per tablet. The majority (96.0%) of tablets contained less than 100 mg MDMA per tablet. There appeared to be a bimodal distribution of MDMA content at approximately 20-40 mg per tablet and 60-80 mg per tablet. There is variability in the MDMA content of ecstasy tablets in the UK. This variability could potentially put users at increased risk of acute harm due to inadvertent excess ingestion of MDMA, as they are unaware of the differences in the MDMA content. Repeat sampling and quantification of MDMA content of ecstasy tablets in the UK will allow better education of users about the potential harms associated with the variability in the MDMA content. In addition, it will provide information to allow the monitoring of changes in not only the MDMA content, but also other adulterants, in ecstasy tablets.

  20. Improving the hardness of dry granulated tablets containing sodium lauryl sulfate.

    PubMed

    Moore, Francis; Okelo, Geoffrey; Colón, Ivelisse; Kushner, Joseph

    2010-11-15

    The impact of the addition of a wetting agent, the surfactant sodium lauryl sulfate (SLS), on the tablet hardness of a dry granulated, solid oral dosage form was investigated. In three batches, SLS was added concurrently with: (1) a poorly soluble, highly hydrophobic active pharmaceutical ingredient (API) and the other excipients prior to the initial blending step, (2) magnesium stearate prior to roller compaction, or (3) magnesium stearate prior to tableting. A fourth batch, which did not contain SLS, served as a control. The maximum hardness of 100 mg, 1/4″-SRC tablets for the four batches--SLS added initially, prior to roller compaction, prior to tableting, and no SLS--were 61±3, 71±3, 89±5, and 86±3N, respectively, suggesting reduced processing of SLS improves tablet hardness by ∼50%. Dissolution of the tablets in 900 ml of simulated gastric fluid with paddles at 75 rpm showed that: (1) there was no impact on the insertion point of SLS into the process on API dissolution, and (2) that the presence of SLS improved dissolution by 5% compared to the control tablets. Adding SLS just prior to tableting can improve tablet hardness and yield similar dissolution performance relative to SLS addition prior to the initial blending step. Copyright © 2010 Elsevier B.V. All rights reserved.

  1. Oral Delivery of Probiotics in Poultry Using pH-Sensitive Tablets.

    PubMed

    Jiang, Tao; Li, Hui-Shan; Han, Geon Goo; Singh, Bijay; Kang, Sang-Kee; Bok, Jin-Duck; Kim, Dae-Duk; Hong, Zhong-Shan; Choi, Yun-Jaie; Cho, Chong-Su

    2017-04-28

    As alternatives to antibiotics in livestocks, probiotics have been used, although most of them in the form of liquid or semisolid formulations, which show low cell viability after oral administration. Therefore, suitable dry dosage forms should be developed for livestocks to protect probiotics against the low pH in the stomach such that the products have higher probiotics survivability. Here, in order to develop a dry dosage forms of probiotics for poultry, we used hydroxypropyl methylcellulose phthalate 55 (HPMCP 55) as a tablet-forming matrix to develop probiotics in a tablet form for poultry. Here, we made three different kinds of probiotics-loaded tablet under different compression forces and investigated their characteristics based on their survivability, morphology, disintegration time, and kinetics in simulated gastrointestinal fluid. The results indicated that the probiotics formulated in the tablets displayed higher survival rates in acidic gastric conditions than probiotics in solution. Rapid release of the probiotics from the tablets occurred in simulated intestinal fluid because of fast swelling of the tablets in neutral pH. As a matrix of tablet, HPMCP 55 provided good viability of probiotics after 6 months under refrigeration. Moreover, after oral administration of probiotics-loaded tablets to chicken, more viable probiotics were observed, than with solution type, through several digestive areas of chicken by the tablets.

  2. Isoniazid, Pyrazinamide and Rifampicin Content Variation in Split Fixed-Dose Combination Tablets

    PubMed Central

    Pouplin, Thomas; Phuong, Pham Nguyen; Toi, Pham Van; Nguyen Pouplin, Julie; Farrar, Jeremy

    2014-01-01

    Setting In most developing countries, paediatric tuberculosis is treated with split tablets leading to potential inaccuracy in the dose delivery and drug exposure. There is no data on the quality of first-line drugs content in split fixed-dose combination tablets. Objective To determine Isoniazid, Pyrazinamide and Rifampicin content uniformity in split FDC tablets used in the treatment of childhood tuberculosis. Design Drug contents of 15 whole tablets, 30 half tablets and 36 third tablets were analysed by high performance liquid chromatography. The content uniformity was assessed by comparing drug content measured in split portions with their expected amounts and the quality of split portions was assessed applying qualitative specifications for whole tablets. Results All whole tablets measurements fell into the USP proxy for the three drugs. But a significant number of half and third portions was found outside the tolerated variation range and the split formulation failed the requirements for content uniformity. To correct for the inaccuracy of splitting the tablets into equal portions, a weight-adjustment strategy was used but this did not improve the findings. Conclusion In split tablets the content of the three drugs is non-uniform and exceeded the USP recommendations. There is an absolute need to make child-friendly formulations available for the treatment of childhood tuberculosis. PMID:25004128

  3. Isoniazid, pyrazinamide and rifampicin content variation in split fixed-dose combination tablets.

    PubMed

    Pouplin, Thomas; Phuong, Pham Nguyen; Toi, Pham Van; Nguyen Pouplin, Julie; Farrar, Jeremy

    2014-01-01

    In most developing countries, paediatric tuberculosis is treated with split tablets leading to potential inaccuracy in the dose delivery and drug exposure. There is no data on the quality of first-line drugs content in split fixed-dose combination tablets. To determine Isoniazid, Pyrazinamide and Rifampicin content uniformity in split FDC tablets used in the treatment of childhood tuberculosis. Drug contents of 15 whole tablets, 30 half tablets and 36 third tablets were analysed by high performance liquid chromatography. The content uniformity was assessed by comparing drug content measured in split portions with their expected amounts and the quality of split portions was assessed applying qualitative specifications for whole tablets. All whole tablets measurements fell into the USP proxy for the three drugs. But a significant number of half and third portions was found outside the tolerated variation range and the split formulation failed the requirements for content uniformity. To correct for the inaccuracy of splitting the tablets into equal portions, a weight-adjustment strategy was used but this did not improve the findings. In split tablets the content of the three drugs is non-uniform and exceeded the USP recommendations. There is an absolute need to make child-friendly formulations available for the treatment of childhood tuberculosis.

  4. Analysis of large-scale tablet coating: Modeling, simulation and experiments.

    PubMed

    Boehling, P; Toschkoff, G; Knop, K; Kleinebudde, P; Just, S; Funke, A; Rehbaum, H; Khinast, J G

    2016-07-30

    This work concerns a tablet coating process in an industrial-scale drum coater. We set up a full-scale Design of Simulation Experiment (DoSE) using the Discrete Element Method (DEM) to investigate the influence of various process parameters (the spray rate, the number of nozzles, the rotation rate and the drum load) on the coefficient of inter-tablet coating variation (cv,inter). The coater was filled with up to 290kg of material, which is equivalent to 1,028,369 tablets. To mimic the tablet shape, the glued sphere approach was followed, and each modeled tablet consisted of eight spheres. We simulated the process via the eXtended Particle System (XPS), proving that it is possible to accurately simulate the tablet coating process on the industrial scale. The process time required to reach a uniform tablet coating was extrapolated based on the simulated data and was in good agreement with experimental results. The results are provided at various levels of details, from thorough investigation of the influence that the process parameters have on the cv,inter and the amount of tablets that visit the spray zone during the simulated 90s to the velocity in the spray zone and the spray and bed cycle time. It was found that increasing the number of nozzles and decreasing the spray rate had the highest influence on the cv,inter. Although increasing the drum load and the rotation rate increased the tablet velocity, it did not have a relevant influence on the cv,inter and the process time. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Mobile Tablet Use among Academic Physicians and Trainees

    PubMed Central

    Sclafani, Joseph; Tirrell, Timothy F.

    2014-01-01

    The rapid adoption rate and integration of mobile technology (tablet computing devices and smartphones) by physicians is reshaping the current clinical landscape. These devices have sparked an evolution in a variety of arenas, including educational media dissemination, remote patient data access and point of care applications. Quantifying usage patterns of clinical applications of mobile technology is of interest to understand how these technologies are shaping current clinical care. A digital survey examining mobile tablet and associated application usage was administered via email to all ACGME training programs. Data regarding respondent specialty, level of training, and habits of tablet usage were collected and analyzed. 40 % of respondents used a tablet, of which the iPad was the most popular. Nearly half of the tablet owners reported using the tablet in clinical settings; the most commonly used application types were point of care and electronic medical record access. Increased level of training was associated with decreased support for mobile computing improving physician capabilities and patient interactions. There was strong and consistent desire for institutional support of mobile computing and integration of mobile computing technology into medical education. While many physicians are currently purchasing mobile devices, often without institutional support, successful integration of these devices into the clinical setting is still developing. Potential reasons behind the low adoption rate may include interference of technology in doctor-patient interactions or the lack of appropriate applications available for download. However, the results convincingly demonstrate that physicians recognize a potential utility in mobile computing, indicated by their desire for institutional support and integration of mobile technology into medical education. It is likely that the use of tablet computers in clinical practice will expand in the future. Thus, we believe

  6. Abuse and diversion of buprenorphine sublingual tablets and film.

    PubMed

    Lavonas, Eric J; Severtson, S Geoffrey; Martinez, Erin M; Bucher-Bartelson, Becki; Le Lait, Marie-Claire; Green, Jody L; Murrelle, Lenn E; Cicero, Theodore J; Kurtz, Steven P; Rosenblum, Andrew; Surratt, Hilary L; Dart, Richard C

    2014-07-01

    Buprenorphine abuse is common worldwide. Rates of abuse and diversion of three sublingual buprenorphine formulations (single ingredient tablets; naloxone combination tablets and film) were compared. Data were obtained from the Researched Abuse, Diversion, and Addiction-Related Surveillance (RADARS) System Poison Center, Drug Diversion, Opioid Treatment (OTP), Survey of Key Informants' Patients (SKIP), and College Survey Programs through December 2012. To control for drug availability, event ratios (rates) were calculated quarterly, based on the number of patients filling prescriptions for each formulation ("unique recipients of a dispensed drug," URDD) and averaged and compared using negative binomial regression. Abuse rates in the OTP, SKIP, and College Survey Programs were greatest for single ingredient tablets, and abuse rates in the Poison Center Program and illicit diversion rates were greatest for the combination tablets. Combination film rates were significantly less than rates for either tablet formulation in all programs. No geographic pattern could be discerned. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

  7. Leveraging Electronic Tablets for General Pediatric Care

    PubMed Central

    McKee, S.; Dugan, T.M.; Downs, S.M.

    2015-01-01

    Summary Background We have previously shown that a scan-able paper based interface linked to a computerized clinical decision support system (CDSS) can effectively screen patients in pediatric waiting rooms and support the physician using evidence based care guidelines at the time of clinical encounter. However, the use of scan-able paper based interface has many inherent limitations including lacking real time communication with the CDSS and being prone to human and system errors. An electronic tablet based user interface can not only overcome these limitations, but may also support advanced functionality for clinical and research use. However, use of such devices for pediatric care is not well studied in clinical settings. Objective In this pilot study, we enhance our pediatric CDSS with an electronic tablet based user interface and evaluate it for usability as well as for changes in patient questionnaire completion rates. Methods Child Health Improvement through Computers Leveraging Electronic Tablets or CHICLET is an electronic tablet based user interface. It is developed to augment the existing scan-able paper interface to our CDSS. For the purposes of this study, we deployed CHICLET in one outpatient pediatric clinic. Usability factors for CHICLET were evaluated via caregiver and staff surveys. Results When compared to the scan-able paper based interface, we observed an 18% increase or 30% relative increase in question completion rates using CHICLET. This difference was statistically significant. Caregivers and staff survey results were positive for using CHICLET in clinical environment. Conclusions Electronic tablets are a viable interface for capturing patient self-report in pediatric waiting rooms. We further hypothesize that the use of electronic tablet based interfaces will drive advances in computerized clinical decision support and create opportunities for patient engagement. PMID:25848409

  8. 21 CFR 520.903e - Febantel tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Febantel tablets. 520.903e Section 520.903e Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.903e Febantel tablets. (a...

  9. How Tablets Are Utilized in the Classroom

    ERIC Educational Resources Information Center

    Ditzler, Christine; Hong, Eunsook; Strudler, Neal

    2016-01-01

    New technologies are a large part of the educational landscape in the 21st century. Emergent technologies are implemented in the classroom at an exponential rate. The newest technology to be added to the daily classroom is the tablet computer. Understanding students' and teachers' perceptions about the role of tablet computers is important as this…

  10. Bioavailability of syrup and tablet formulations of cefetamet pivoxil.

    PubMed

    Ducharme, M P; Edwards, D J; McNamara, P J; Stoeckel, K

    1993-12-01

    Two studies examining the bioavailability of cefetamet pivoxil in healthy male subjects were conducted. In the first, the bioavailabilities of the 250-mg (M250) and M500 tablet formulations of cefetamet pivoxil to be marketed were compared with that of a tablet used in clinical trials. All products were given with food at a dose of 500 mg. In the second study, the bioavailability of the syrup formulation was evaluated under both fasting and nonfasting conditions and compared with that of the M500 tablet formulation given with food. The absolute bioavailabilities of the M500 and M250 tablets (55.0% +/- 8.0% and 55.7% +/- 7.0%, respectively) were not significantly different from that of the clinical-trial formulation (49.8% +/- 8.5%). The newer tablet formulations exhibited faster absorption as evidenced by higher peak concentrations (3.8 [M500] and 3.9 [M250] mg/liter compared with 3.2 mg/liter for the clinical-trial formulation), a shorter time to peak concentration, and a shorter mean absorption time. The syrup formulation was found to have significantly lower absolute bioavailability (37.9% +/- 6.0%) compared with that of the M500 tablet (58.4% +/- 9.0%) when both were given with food. Food had no significant effect on the bioavailability of the syrup, which averaged 34.0% +/- 8.6% under fasting conditions, although absorption was delayed by food (mean absorption time increased from 2.2 to 3.9 h). This contrasts with the results of previous studies documenting significant increases in tablet bioavailability with food. Despite the lower bioavailability of the syrup, unbound-cefetamet concentrations are expected to remain above the MICs for 90% of the strains tested for susceptible organisms for approximately 10 h of the usual 12-h dosing interval with both syrup and tablet formulations of cefetamet pivoxil given with food.

  11. Bioavailability of syrup and tablet formulations of cefetamet pivoxil.

    PubMed Central

    Ducharme, M P; Edwards, D J; McNamara, P J; Stoeckel, K

    1993-01-01

    Two studies examining the bioavailability of cefetamet pivoxil in healthy male subjects were conducted. In the first, the bioavailabilities of the 250-mg (M250) and M500 tablet formulations of cefetamet pivoxil to be marketed were compared with that of a tablet used in clinical trials. All products were given with food at a dose of 500 mg. In the second study, the bioavailability of the syrup formulation was evaluated under both fasting and nonfasting conditions and compared with that of the M500 tablet formulation given with food. The absolute bioavailabilities of the M500 and M250 tablets (55.0% +/- 8.0% and 55.7% +/- 7.0%, respectively) were not significantly different from that of the clinical-trial formulation (49.8% +/- 8.5%). The newer tablet formulations exhibited faster absorption as evidenced by higher peak concentrations (3.8 [M500] and 3.9 [M250] mg/liter compared with 3.2 mg/liter for the clinical-trial formulation), a shorter time to peak concentration, and a shorter mean absorption time. The syrup formulation was found to have significantly lower absolute bioavailability (37.9% +/- 6.0%) compared with that of the M500 tablet (58.4% +/- 9.0%) when both were given with food. Food had no significant effect on the bioavailability of the syrup, which averaged 34.0% +/- 8.6% under fasting conditions, although absorption was delayed by food (mean absorption time increased from 2.2 to 3.9 h). This contrasts with the results of previous studies documenting significant increases in tablet bioavailability with food. Despite the lower bioavailability of the syrup, unbound-cefetamet concentrations are expected to remain above the MICs for 90% of the strains tested for susceptible organisms for approximately 10 h of the usual 12-h dosing interval with both syrup and tablet formulations of cefetamet pivoxil given with food. PMID:8109939

  12. 21 CFR 520.2150b - Stanozolol chewable tablets.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... treatment in dogs. (2) Administered orally to small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. (3) Federal law restricts...

  13. 21 CFR 520.2150b - Stanozolol chewable tablets.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... treatment in dogs. (2) Administered orally to small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. (3) Federal law restricts...

  14. 21 CFR 520.2150b - Stanozolol chewable tablets.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... treatment in dogs. (2) Administered orally to small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. (3) Federal law restricts...

  15. 21 CFR 520.2150b - Stanozolol chewable tablets.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... treatment in dogs. (2) Administered orally to small breeds of dogs, 1/2 to 1 tablet twice daily for several weeks; to large breeds of dogs, 1 to 2 tablets twice daily for several weeks. (3) Federal law restricts...

  16. Production of extended release mini-tablets using directly compressible grades of HPMC.

    PubMed

    Mohamed, Faiezah A A; Roberts, Matthew; Seton, Linda; Ford, James L; Levina, Marina; Rajabi-Siahboomi, Ali R

    2013-11-01

    Hypromellose (HPMC) has been previously used to control drug release from mini-tablets. However, owing to poor flow, production of mini-tablets containing high HPMC levels is challenging. Directly compressible (DC) HPMC grades have been developed by Dow Chemical Company. To compare the properties of HPMC DC (METHOCEL™ K4M and K100M) with regular (REG) HPMC grades. Particle size distribution and flowability of HPMC REG and DC were evaluated. 3 mm mini-tablets, containing hydrocortisone or theophylline as model drugs and 40% w/w HPMC DC or REG were produced. Mini-tablets containing HPMC DC grades were manufactured using a rotary press simulator at forces between 2-4 kN and speeds of 5, 10, 15 or 20 rpm. Mini-tablets containing HPMC REG were produced manually. The improved flowability of HPMC DC grades, which have a narrower particle size distribution and larger particle sizes, meant that simulated large scale production of mini-tablets with good weight uniformity (CV 1.79-4.65%) was feasible. It was not possible to automatically manufacture mini-tablets containing HPMC REG due to the poor flowability of the formulations. Drug release from mini-tablets comprising HPMC DC and REG were comparable. Mini-tablets containing HPMC DC illustrated a higher tensile strength compared to mini-tablets made with HPMC REG. Mini-tablets produced with HPMC DC at different compression speeds had similar drug release profiles. Production of extended release mini-tablets was successfully achieved when HPMC DC was used. Drug release rate was not influenced by the different HPMC DC grades (K4M or K100M) or production speed.

  17. Learner-Centred Mathematics and Statistics Education Using Netbook Tablet PCs

    ERIC Educational Resources Information Center

    Loch, Birgit; Galligan, Linda; Hobohm, Carola; McDonald, Christine

    2011-01-01

    Tablet technology has been shown to support learner-centred mathematics education when this technology is available to both the lecturer and the students. However, cost is often the barrier to students' use of tablet PCs for their university studies. This article argues that more affordable netbook PCs with tablet capabilities can be viable…

  18. Chitinosans as tableting excipients for modified release delivery systems.

    PubMed

    Rege, P R; Shukla, D J; Block, L H

    1999-04-20

    The term 'chitinosans' embraces the spectrum of acetylated poly(N-glucosamines) ranging from chitin to chitosan. Chitinosans (I), at acidic pH, have protonated amines which can interact with oppositely charged drug ions and, thereby, modify drug release from drug delivery systems. Tablets were compressed from a physical mixture containing salicylic acid (II) as the model drug, I, and magnesium stearate. Five commercial I compounds, varying in degree of deacetylation and molecular weight, were selected. Tablets were compressed at 5000, 10 000, and 15 000 psig using a Carver and a single punch tablet press. The differential scanning calorimetry thermograms provided evidence of I-II interaction in the powder blend. Analysis of variance (ANOVA) indicated that the compression pressure did not significantly affect the crushing strength (CS) or the release profile of II from the I-matrix tablets (P?0.05). Furthermore, the ANOVA also indicated that the tablet press used during manufacture did not affect the above properties (P?0.05); however, the chitinosans significantly affected the CS as well as the release profile of II from I-matrix tablets (P<0.05). This study provides further evidence for the use of commercial I compounds as excipients for use in modified release drug delivery systems. Copyright.

  19. Tablet PCs: A Physical Educator's New Clipboard

    ERIC Educational Resources Information Center

    Nye, Susan B.

    2010-01-01

    Computers in education have come a long way from the abacus of 5,000 years ago to the desktop and laptop computers of today. Computers have transformed the educational environment, and with each new iteration of smaller and more powerful machines come additional advantages for teaching practices. The Tablet PC is one. Tablet PCs are fully…

  20. Electric current density imaging of tablet dissolution.

    PubMed

    Mikac, Ursa; Demsar, Alojz; Sersa, Igor; Demsar, Franci

    2002-01-01

    The Electric current density imaging technique (CDI) was used to monitor the dissolution of and ion migration from tablets of different acids in agar-agar gel. Conventional MRI cannot monitor these processes, since it can only show changes in the size of the tablet during the dissolving process. CDI traces the dissolved ions thanks to changes in conductivity.

  1. Improving the drug release of Naproxen Sodium tablets by preparing granules and tablets with a preferred mixing ratio of hydrates.

    PubMed

    Bär, David; Debus, Heiko; Grune, Christian; Tosch, Stephan; Fischer, Wolfgang; Mäder, Karsten; Imming, Peter

    2017-12-01

    Naproxen is a typical and well-known analgesic classified as non-steroidal anti-inflammatory drug (NSAID) and is commercialized as tablets or liquid-filled capsules. Naproxen is typically used asa sodium salt because of its better processability compared to Naproxen free acid. This entails hygroscopicity and gives rise to the existence of four different hydrates, which show polymorphic and pseudopolymorphic properties. Solid dosage forms containing Naproxen Sodium often have to be processed in an applicable dosage form by granulation and tablet compression. During granulation, Naproxen Sodium will be in contact with water and is exposed to the drop and rise in temperature and to mechanical stress. The result could be a mixture of different hydrates of Naproxen Sodium. This study showed that a modified designed fluid bed granulation was not affected by differences in the mixing ratio of hydrates when using different water contents after spraying and at the end with the finished granules. Here, X-ray diffraction combined with Rietveld refinement was used to analyze the ratio of the hydrates and its identity. All granulation batches showed a large amount of Naproxen Sodium Monohydrate (>87%) and no differences could be observed during tablet compression. Quantities of other hydrates were negligibly small. Furthermore, this study also demonstrated the influence of tablet compression by transforming the hydrates of the granules. In addition to Naproxen Sodium Monohydrate, a large quantity of amorphous structures has also been found. Rietveld evaluation combined with the preliminary studies of the raw hydrates provided conclusions on the drug release of the tablets containing hydrates of Naproxen Sodium which were influenced by tablet compression. Fast drug release was obtained when a maximum water content of about 21% was used after spraying during granulation, independently of the final water content of the finished granules. A maximum water content of less than 21

  2. Pharmacokinetics of Lopinavir/Ritonavir Crushed versus Whole Tablets in Children

    PubMed Central

    Best, Brookie M.; Capparelli, Edmund V.; Diep, Huy; Rossi, Steven S.; Farrell, Michael J.; Williams, Elaine; Lee, Grace; van den Anker, John N.; Rakhmanina, Natella

    2011-01-01

    Objective Lopinavir/ritonavir (Kaletra®) is first line therapy for pediatric HIV infection. In clinical practice, Kaletra® tablets are occasionally crushed for pediatric administration. This study compared lopinavir/ritonavir exposure between whole and crushed tablets in HIV-infected children. Design This was a randomized, open-label, cross-over study of pediatric patients taking lopinavir/ritonavir as part of their antiretroviral regimen. Each subject had two separate (within 30 days) steady-state 12-hour pharmacokinetic (PK) studies with crushed and whole 200/50 mg lopinavir/ritonavir tablets. Methods PK blood samples were drawn at 0 (pre-dose), 1, 2, 4, 6, 8, and 12 hours post-dose. Lopinavir and ritonavir plasma concentrations measured by high performance liquid chromatography were used to calculate non-compartmental area under the concentration versus time curve (AUC) and clearance (CL/F). Wilcoxon signed-rank tests compared PK values between crushed and whole tablets. Results Twelve children, median age of 13 years (10–16 years), took 550/138 mg/m2/day lopinavir/ritonavir divided every 12 hours. The median lopinavir AUC following crushed and whole tablets were 92 mg*hr/L and 144 mg*hr/L, respectively, with an AUC ratio of 0.55 (p=0.003). Median ritonavir AUC of crushed and whole tablets were 7 mg*hr/L and 13.3 mg*hr/L, respectively, with an AUC ratio of 0.53 (p=0.006). Conclusions Administration of crushed 200/50 mg lopinavir/ritonavir tablets to children significantly reduced lopinavir and ritonavir exposure with a decrease in AUC by 45% and 47%, respectively. The administration of crushed tablets would require higher doses and therapeutic drug monitoring to ensure adequate lopinavir exposure in patients requiring this practice. The use of crushed lopinavir/ritonavir tablets should be avoided, if possible. PMID:21876444

  3. Student Perceptions of Using Tablet Technology in Post-Secondary Classes

    ERIC Educational Resources Information Center

    Mang, Colin F.; Wardley, Leslie J.

    2013-01-01

    This paper assesses students' attitudes towards using tablets, such as the Apple iPad, in university classes. Tablets are found to be a substitute for laptop computers. Students initially expressed a great deal of optimism regarding the technology, and, although their views diminished slightly as they gained experience with using a tablet,…

  4. Validation of tablet-based evaluation of color fundus images

    PubMed Central

    Christopher, Mark; Moga, Daniela C.; Russell, Stephen R.; Folk, James C.; Scheetz, Todd; Abràmoff, Michael D.

    2012-01-01

    Purpose To compare diabetic retinopathy (DR) referral recommendations made by viewing fundus images using a tablet computer to recommendations made using a standard desktop display. Methods A tablet computer (iPad) and a desktop PC with a high-definition color display were compared. For each platform, two retinal specialists independently rated 1200 color fundus images from patients at risk for DR using an annotation program, Truthseeker. The specialists determined whether each image had referable DR, and also how urgently each patient should be referred for medical examination. Graders viewed and rated the randomly presented images independently and were masked to their ratings on the alternative platform. Tablet- and desktop display-based referral ratings were compared using cross-platform, intra-observer kappa as the primary outcome measure. Additionally, inter-observer kappa, sensitivity, specificity, and area under ROC (AUC) were determined. Results A high level of cross-platform, intra-observer agreement was found for the DR referral ratings between the platforms (κ=0.778), and for the two graders, (κ=0.812). Inter-observer agreement was similar for the two platforms (κ=0.544 and κ=0.625 for tablet and desktop, respectively). The tablet-based ratings achieved a sensitivity of 0.848, a specificity of 0.987, and an AUC of 0.950 compared to desktop display-based ratings. Conclusions In this pilot study, tablet-based rating of color fundus images for subjects at risk for DR was consistent with desktop display-based rating. These results indicate that tablet computers can be reliably used for clinical evaluation of fundus images for DR. PMID:22495326

  5. Hand-held internet tablets for school-based data collection.

    PubMed

    Denny, Simon J; Milfont, Taciano L; Utter, Jennifer; Robinson, Elizabeth M; Ameratunga, Shanthi N; Merry, Sally N; Fleming, Theresa M; Watson, Peter D

    2008-07-26

    In the last 20 years, researchers have been using computer self-administered questionnaires to gather data on a wide range of adolescent health related behaviours. More recently, researchers collecting data in schools have started to use smaller hand-held computers for their ease of use and portability. The aim of this study is to describe a new technology with wi-fi enabled hand-held internet tablets and to compare adolescent preferences of laptop computers or hand-held internet tablets in administering a youth health and well-being questionnaire in a school setting. A total of 177 students took part in a pilot study of a national youth health and wellbeing survey. Students were randomly assigned to internet tablets or laptops at the start of the survey and were changed to the alternate mode of administration about half-way through the questionnaire. Students at the end of the questionnaire were asked which of the two modes of administration (1) they preferred, (2) was easier to use, (3) was more private and confidential, and (4) was easier to answer truthfully. Many students expressed no preference between laptop computers or internet tablets. However, among the students who expressed a preference between laptop computers or internet tablets, the majority of students found the internet tablets more private and confidential (p < 0.001) and easier to answer questions truthfully (p < 0.001) compared to laptop computers. This study demonstrates that using wi-fi enabled hand-held internet tablets is a feasible methodology for school-based surveys especially when asking about sensitive information.

  6. Hand-held internet tablets for school-based data collection

    PubMed Central

    Denny, Simon J; Milfont, Taciano L; Utter, Jennifer; Robinson, Elizabeth M; Ameratunga, Shanthi N; Merry, Sally N; Fleming, Theresa M; Watson, Peter D

    2008-01-01

    Background In the last 20 years, researchers have been using computer self-administered questionnaires to gather data on a wide range of adolescent health related behaviours. More recently, researchers collecting data in schools have started to use smaller hand-held computers for their ease of use and portability. The aim of this study is to describe a new technology with wi-fi enabled hand-held internet tablets and to compare adolescent preferences of laptop computers or hand-held internet tablets in administering a youth health and well-being questionnaire in a school setting. Methods A total of 177 students took part in a pilot study of a national youth health and wellbeing survey. Students were randomly assigned to internet tablets or laptops at the start of the survey and were changed to the alternate mode of administration about half-way through the questionnaire. Students at the end of the questionnaire were asked which of the two modes of administration (1) they preferred, (2) was easier to use, (3) was more private and confidential, and (4) was easier to answer truthfully. Results Many students expressed no preference between laptop computers or internet tablets. However, among the students who expressed a preference between laptop computers or internet tablets, the majority of students found the internet tablets more private and confidential (p < 0.001) and easier to answer questions truthfully (p < 0.001) compared to laptop computers. Conclusion This study demonstrates that using wi-fi enabled hand-held internet tablets is a feasible methodology for school-based surveys especially when asking about sensitive information. PMID:18710505

  7. Correlating bilayer tablet delamination tendencies to micro-environmental thermodynamic conditions during pan coating.

    PubMed

    Zacour, Brian M; Pandey, Preetanshu; Subramanian, Ganeshkumar; Gao, Julia Z; Nikfar, Faranak

    2014-06-01

    The objective of this study was to determine the impact that the micro-environment, as measured by PyroButton data loggers, experienced by tablets during the pan coating unit operation had on the layer adhesion of bilayer tablets in open storage conditions. A full factorial design of experiments (DOE) with three center points was conducted to study the impact of final tablet hardness, film coating spray rate and film coating exhaust temperature on the delamination tendencies of bilayer tablets. PyroButton data loggers were placed (fixed) at various locations in a pan coater and were also allowed to freely move with the tablet bed to measure the micro-environmental temperature and humidity conditions of the tablet bed. The variance in the measured micro-environment via PyroButton data loggers accounted for 75% of the variance in the delamination tendencies of bilayer tablets on storage (R(2 )= 0.75). A survival analysis suggested that tablet hardness and coating spray rate significantly impacted the delamination tendencies of the bilayer tablets under open storage conditions. The coating exhaust temperature did not show good correlation with the tablets' propensity to crack indicating that it was not representative of the coating micro-environment. Models created using data obtained from the PyroButton data loggers outperformed models created using primary DOE factors in the prediction of bilayer tablet strength, especially upon equipment or scale transfers. The coating micro-environment experienced by tablets during the pan coating unit operation significantly impacts the strength of the bilayer interface of tablets on storage.

  8. [Mechanism of Tongsaimai tablet for atherosclerosis based on network pharmacology].

    PubMed

    Li, Na; Zhang, Xin-Zhuang; Wang, Yan-Ru; Cao, Liang; Ding, Gang; Wang, Zhen-Zhong; Xiao, Wei; Xu, Xiao-Jie

    2016-05-01

    Network pharmacology method was adopted in this study to explore the active compounds and mechanism of Tongsaimai tablets for atherosclerosis. In molecular docking and molecular-target protein network analysis, 97 molecules in Tongsaimai tablets showed good interaction with the atherosclerosis-related target protein (docking score ≥ 7), and 37 molecules of them could act on more than 2 targets (≥ 2) with higher betweenness, suggesting that these 37 molecules might be the main active compounds group in Tongsaimai tablets for atherosclerosis treatment. Furthermore, the predicted active compounds contained more flavonoids and saponins, reminding more attention should be paid on flavonoids and saponins in study of effective compounds and quality standards of Tongsaimai tablets. Targets network analysis showed that, the active compounds of Tongsaimai tablets could regulate inflammation, stabilize plaque, protect vascular endothelial cell, regulate blood lipid and inhibit blood coagulation through acting on the main 22 target proteins, such as Toll-like receptors (TLR1, TLR2), matrix metalloproteinase (MMP1, MMP2, MMP3, MMP9), angiotensin converting enzyme (ACE), leukotriene A4 hydrolase (LTA4-H), 5-lipoxidase (5-LOX), peroxisome proliferators-activated receptors (PPARα, PPARγ). These active compounds can participate in regulating different pathologic stages of atherosclerosis and thus treat atherosclerosis finally. This study revealed the main active compounds and possible mechanism of Tongsaimai tablets for treatment of atherosclerosis and meanwhile, verified the characteristics of multi-components, multi-targets and integral regulation for Tongsaimai tablets, providing theoretical references for the following systematic laboratory experiments on effective compounds and action mechanism of Tongsaimai Tablet. Copyright© by the Chinese Pharmaceutical Association.

  9. Learner-centred mathematics and statistics education using netbook tablet PCs

    NASA Astrophysics Data System (ADS)

    Loch, Birgit; Galligan, Linda; Hobohm, Carola; McDonald, Christine

    2011-10-01

    Tablet technology has been shown to support learner-centred mathematics education when this technology is available to both the lecturer and the students. However, cost is often the barrier to students' use of tablet PCs for their university studies. This article argues that more affordable netbook PCs with tablet capabilities can be viable alternatives to full-sized tablet PCs to enhance active and collaborative learning in mathematics and statistics. For a whole teaching semester, netbook tablet PCs were given to volunteer students from two different cohorts. Students were enrolled in nursing mathematics or introductory statistics in non-mathematics majors at an Australian university. The aims were to gauge the suitability of this technology and to identify what active and collaborative learning emerged in these first-year classes. While the netbook tablet PCs were actively promoted in their tutorials, of additional interest was students' use of the technology for any aspect of their studies both inside and outside the classroom. The outcome of this study was to inform a university decision to provide inexpensive tablet technology to larger cohorts of students. The results highlight different approaches required in the mathematics and statistics classes to achieve collaborative and active learning facilitated through the technology. Environmental variables such as the tutor, student, learning space, availability of other technologies and subject content had an impact on the nature of learning. While learner-centred education can be facilitated by inexpensive netbook tablet PCs, we caution that the savings may come at the expense of computing power.

  10. Triiodothyronine and thyroxine content of desiccated thyroid tablets.

    PubMed

    Rees-Jones, R W; Larsen, P R

    1977-11-01

    Triiodothyronine (T3) and thyroxine (T4) were measured by radioimmunoassay in Pronase hydrolysates of four lots each of 1- and 2-grain tablets of desiccated thyroid (Thyroid, Armour) and thyroglobulin (Proloid, Warner-Chilcott). The methodology used was verified by studies of tablets containing known quantities of T4 and T3. One grain of desiccated thyroid contained 12 +/- 1 and 64 +/- 3 microgram (mean +/- SD) of T3 and T4 per tablet, respectively (T4/T3 molar ratio, 4.3). A 1-grain tablet of thyroglobulin contained 16 +/- 2 and 55 +/- 5 microgram of T3 and T4, respectively with a T4/T3 ratio of 2.9. Two-grain tablets generally contained twice the quantity of T3 and T4 in the 1-grain preparations. The variation in T3 and T4 content between the four lots of each tablet strength for each product was 10% or less. These estimates of T3 and T4 content are 1.5- to 2-fold greater than those previously published. This difference probably results from the more sophisticated methodology now available which does not require chromatographic separation of T3 and T4 or iodometry. Using calculations based on published estimates of T4 and T3 absorption and of the T3/T4 potency ratio, it would appear that the T3 content of desiccated thyroid and thyroglobulin provide approximately 39% and 51%, respectively, of the thyromimetic activity of these two medications.

  11. Tablet-based cardiac arrest documentation: a pilot study.

    PubMed

    Peace, Jack M; Yuen, Trevor C; Borak, Meredith H; Edelson, Dana P

    2014-02-01

    Conventional paper-based resuscitation transcripts are notoriously inaccurate, often lacking the precision that is necessary for recording a fast-paced resuscitation. The aim of this study was to evaluate whether a tablet computer-based application could improve upon conventional practices for resuscitation documentation. Nurses used either the conventional paper code sheet or a tablet application during simulated resuscitation events. Recorded events were compared to a gold standard record generated from video recordings of the simulations and a CPR-sensing defibrillator/monitor. Events compared included defibrillations, medication deliveries, and other interventions. During the study period, 199 unique interventions were observed in the gold standard record. Of these, 102 occurred during simulations recorded by the tablet application, 78 by the paper code sheet, and 19 during scenarios captured simultaneously by both documentation methods These occurred over 18 simulated resuscitation scenarios, in which 9 nurses participated. The tablet application had a mean sensitivity of 88.0% for all interventions, compared to 67.9% for the paper code sheet (P=0.001). The median time discrepancy was 3s for the tablet, and 77s for the paper code sheet when compared to the gold standard (P<0.001). Similar to prior studies, we found that conventional paper-based documentation practices are inaccurate, often misreporting intervention delivery times or missing their delivery entirely. However, our study also demonstrated that a tablet-based documentation method may represent a means to substantially improve resuscitation documentation quality, which could have implications for resuscitation quality improvement and research. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  12. A Tablet for Healthy Ageing: The Effect of a Tablet Computer Training Intervention on Cognitive Abilities in Older Adults.

    PubMed

    Vaportzis, Eleftheria; Martin, Mike; Gow, Alan J

    2017-08-01

    To test the efficacy of a tablet computer training intervention to improve cognitive abilities of older adults. Prospective randomized controlled trial. Community-based aging intervention study, Edinburgh, UK. Forty-eight healthy older adults aged 65 to 76 years were recruited at baseline with no or minimal tablet experience; 43 completed follow-up testing. Twenty-two participants attended a weekly 2-hour class for 10 weeks during which they learned how to use a tablet and various applications on it. A battery of cognitive tests from the WAIS-IV measuring the domains of Verbal Comprehension, Perceptual Processing, Working Memory, and Processing Speed, as well as health, psychological, and well-being measures. A 2 × 2 mixed model ANOVA suggested that the tablet intervention group (N = 22) showed greater improvements in Processing Speed (η 2  = 0.10) compared with controls (N = 21), but did not differ in Verbal Comprehension, Perceptual Processing, or Working Memory (η 2 ranged from -0.03 to 0.04). Engagement in a new mentally challenging activity (tablet training) was associated with improved processing speed. Acquiring skills in later life, including those related to adopting new technologies, may therefore have the potential to reduce or delay cognitive changes associated with ageing. It is important to understand how the development of these skills might further facilitate everyday activities, and also improve older adults' quality of life. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  13. Fast disintegrating tablets: Opportunity in drug delivery system

    PubMed Central

    Parkash, Ved; Maan, Saurabh; Deepika; Yadav, Shiv Kumar; Hemlata; Jogpal, Vikas

    2011-01-01

    Fast disintegrating tablets (FDTs) have received ever-increasing demand during the last decade, and the field has become a rapidly growing area in the pharmaceutical industry. Oral drug delivery remains the preferred route for administration of various drugs. Recent developments in the technology have prompted scientists to develop FDTs with improved patient compliance and convenience. Upon introduction into the mouth, these tablets dissolve or disintegrate in the mouth in the absence of additional water for easy administration of active pharmaceutical ingredients. The popularity and usefulness of the formulation resulted in development of several FDT technologies. FDTs are solid unit dosage forms, which disintegrate or dissolve rapidly in the mouth without chewing and water. FDTs or orally disintegrating tablets provide an advantage particularly for pediatric and geriatric populations who have difficulty in swallowing conventional tablets and capsules. This review describes various formulations and technologies developed to achieve fast dissolution/dispersion of tablets in the oral cavity. In particular, this review describes in detail FDT technologies based on lyophilization, molding, sublimation, and compaction, as well as approaches to enhancing the FDT properties, such as spray drying and use of disintegrants. In addition, taste-masking technologies, experimental measurements of disintegration times, and dissolution are also discussed. PMID:22247889

  14. Enabling the Tablet Product Development of 5-Fluorocytosine by Conjugate Acid Base Cocrystals.

    PubMed

    Perumalla, Sathyanarayana R; Paul, Shubhajit; Sun, Changquan C

    2016-06-01

    5-Fluorocytosine (FC) is a high-dose antifungal drug that challenges the development of a tablet product due to poor solid-state stability and tabletability. Using 2 pharmaceutically acceptable conjugate acid base (CAB) cocrystals of FC with HCl and acesulfame, we have developed commercially viable high loading FC tablets. The tablets were prepared by direct compression using nano-coated microcrystalline cellulose Avicel PH105 as a tablet binder, which provided both excellent tabletability and good flowability. Commercial manufacturability of formulations based on both CAB cocrystals was verified on a compaction simulator. The results from an expedited friability study were used to set the compaction force, which yielded tablets with sufficient mechanical strength and rapid tablet disintegration. This work demonstrates the potential value of CAB cocrystals in drug product development. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  15. Design of sustained release tablet containing fucoidan.

    PubMed

    Tran, Thao Truong-Dinh; Ngo, Dai Kieu-Phuong; Vo, Toi Van; Tran, Phuong Ha-Lien

    2015-01-01

    The study introduced a new therapeutic agent, fucoidan, which can offer potential medical treatments including anti-inflammatory and anti-coagulant activities, as well as anti-proliferative effects on cancer cells. Fucoidan was included in sustained release formulations expected for an effective plasma drug concentration for approximately 24 h. The matrices based on the two polymers hydroxypropyl methycellulose (HPMC) and polyethylene oxide (PEO) were prepared with various ratios between the polymers and fucoidan. The dissolution profiles of various matrix tablets performed in enzyme-free simulated intestinal fluid (pH 6.8) for 24 h indicated a higher potential of PEO-based matrix tablets in sustaining release of fucoidan. The swelling and erosion of the tablets were also characterized to elucidate the difference among those dissolution profiles.

  16. Portable Tablets in Science Museum Learning: Options and Obstacles

    NASA Astrophysics Data System (ADS)

    Gronemann, Sigurd Trolle

    2017-06-01

    Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people's learning with portable tablets matches the intentions of the museums. By applying media and information literacy (MIL) components as analytical dimensions, a pattern of discrepancies between young people's expectations, their actual learning and the museums' approaches to framing such learning is identified. It is argued that, paradoxically, museums' decisions to innovate by introducing new technologies, such as portable tablets, and new pedagogies to support them conflict with many young people's traditional ideas of museums and learning. The assessment of the implications of museums' integration of portable tablets indicates that in making pedagogical transformations to accommodate new technologies, museums risk opposing didactic intention if pedagogies do not sufficiently attend to young learners' systemic expectations to learning and to their expectations to the digital experience influenced by their leisure use.

  17. Mechanical property characterization of bilayered tablets using nondestructive air-coupled acoustics.

    PubMed

    Akseli, Ilgaz; Dey, Dipankar; Cetinkaya, Cetin

    2010-03-01

    A noncontact/nondestructive air-coupled acoustic technique to be potentially used in mechanical property determination of bilayer tablets is presented. In the reported experiments, a bilayer tablet is vibrated via an acoustic field of an air-coupled transducer in a frequency range sufficiently high to excite several vibrational modes (harmonics) of the tablet. The tablet vibrational transient responses at a number of measurement points on the tablet are acquired by a laser vibrometer in a noncontact manner. An iterative computational procedure based on the finite element method is utilized to extract the Young's modulus, the Poisson's ratio, and the mass density values of each layer material of a bilayer tablet from a subset of the measured resonance frequencies. For verification purposes, a contact ultrasonic technique based on the time-of-flight data of the longitudinal (pressure) and transverse (shear) acoustic waves in each layer of a bilayer tablet is also utilized. The extracted mechanical properties from the air-coupled acoustic data agree well with those determined from the contact ultrasonic measurements. The mechanical properties of solid oral dosage forms have been shown to impact its mechanical integrity, disintegration profile and the release rate of the drug in the digestive tract, thus potentially affecting its therapeutic response. The presented nondestructive technique provides greater insight into the mechanical properties of the bilayer tablets and has the potential to identify quality and performance problems related to the mechanical properties of the bilayer tablets early on the production process and, consequently, reduce associated cost and material waste.

  18. Tablet-Based Education to Reduce Depression-Related Stigma

    ERIC Educational Resources Information Center

    Lu, Catherine; Winkelman, Megan; Wong, Shane Shucheng

    2016-01-01

    Objectives: This study investigated the efficacy of a tablet-based multimedia education application, the Project Not Alone Depression Module, in improving depression literacy and reducing depression stigma among a community-based mental health clinic population. Methods: A total of 93 participants completed either a tablet-based multimedia…

  19. Three-dimensional capture, representation, and manipulation of Cuneiform tablets

    NASA Astrophysics Data System (ADS)

    Woolley, Sandra I.; Flowers, Nicholas J.; Arvanitis, Theodoros N.; Livingstone, Alasdair; Davis, Tom R.; Ellison, John

    2001-04-01

    This paper presents the digital imaging results of a collaborative research project working toward the generation of an on-line interactive digital image database of signs from ancient cuneiform tablets. An important aim of this project is the application of forensic analysis to the cuneiform symbols to identify scribal hands. Cuneiform tablets are amongst the earliest records of written communication, and could be considered as one of the original information technologies; an accessible, portable and robust medium for communication across distance and time. The earliest examples are up to 5,000 years old, and the writing technique remained in use for some 3,000 years. Unfortunately, only a small fraction of these tablets can be made available for display in museums and much important academic work has yet to be performed on the very large numbers of tablets to which there is necessarily restricted access. Our paper will describe the challenges encountered in the 2D image capture of a sample set of tablets held in the British Museum, explaining the motivation for attempting 3D imaging and the results of initial experiments scanning the smaller, more densely inscribed cuneiform tablets. We will also discuss the tractability of 3D digital capture, representation and manipulation, and investigate the requirements for scaleable data compression and transmission methods. Additional information can be found on the project website: www.cuneiform.net

  20. Crystal coating via spray drying to improve powder tabletability.

    PubMed

    Vanhoorne, V; Peeters, E; Van Snick, B; Remon, J P; Vervaet, C

    2014-11-01

    A continuous crystal coating method was developed to improve both flowability and tabletability of powders. The method includes the introduction of solid, dry particles into an atomized spray during spray drying in order to coat and agglomerate individual particles. Paracetamol was used as a model drug as it exhibits poor flowability and high capping tendency upon compaction. The particle size enlargement and flowability were evaluated by the mean median particle size and flow index of the resulting powders. The crystal coating coprocessing method was successful for the production of powders containing 75% paracetamol with excellent tableting properties. However, the extent of agglomeration achieved during coprocessing was limited. Tablets compressed on a rotary tablet press in manual mode showed excellent compression properties without capping tendency. A formulation with 75% paracetamol, 5% PVP and 20% amorphous lactose yielded a tensile strength of 1.9 MPa at a compression pressure of 288 MPa. The friability of tablets compressed at 188 MPa was only 0.6%. The excellent tabletability of this formulation was attributed to the coating of paracetamol crystals with amorphous lactose and PVP through coprocessing and the presence of brittle and plastic components in the formulation. The coprocessing method was also successfully applied for the production of directly compressible lactose showing improved tensile strength and friability in comparison to a spray dried direct compression lactose grade.

  1. Preparation and biological efficacy of haddock bone calcium tablets

    NASA Astrophysics Data System (ADS)

    Huo, Jiancong; Deng, Shanggui; Xie, Chao; Tong, Guozhong

    2010-03-01

    To investigate the possible use of waste products obtained after processing haddock, the present study prepared haddock bone calcium powder by NaOH and ethanol soaking (alkalinealcohol method) and prepared haddock bone calcium tablets using the powder in combination with appropriate excipients. The biological efficacy of the haddock bone calcium tablets was investigated using Wistar rats as an experiment model. Results show that the optimal parameters for the alkalinealcohol method are: NaOH concentration 1 mol/L, immersion time 30 h; ethanol concentration 60%, immersion time 15 h. A mixture of 2% polyvinylpyrrolidone in ethanol was used as an excipient at a ratio of 1:2 to full-cream milk powder, without the use of a disintegrating agent. This process provided satisfactory tablets in terms of rigidity and taste. Animal studies showed that the haddock bone calcium tablets at a dose of 2 g·kg-1·d-1 or 5g·kg-1·d-1 significantly increased blood calcium and phosphorus levels and bone calcium content in rats. Therefore, these tablets could be used for calcium supplementation and prevent osteoporosis. Although the reasons of high absorption in the rats fed with haddock bone calcium tablets are unclear, it is suggested that there are some factors, such as treatment with method of alkaline-alcohol or the added milk, may play positive roles in increasing absorption ratio.

  2. NMR imaging of high-amylose starch tablets. 1. Swelling and water uptake.

    PubMed

    Baille, Wilms E; Malveau, Cédric; Zhu, Xiao Xia; Marchessault, Robert H

    2002-01-01

    Pharmaceutical tablets made of modified high-amylose starch have a hydrophilic polymer matrix into which water can penetrate with time to form a hydrogel. Nuclear magnetic resonance imaging was used to study the water penetration and the swelling of the matrix of these tablets. The tablets immersed in water were imaged at different time intervals on a 300 MHz NMR spectrometer. Radial images show clearly the swelling of the tablets and the water concentration profile. The rate constants for water diffusion and the tablet swelling were extracted from the experimental data. The water diffusion process was found to follow case II kinetics at 25 degrees C. NMR imaging also provided spin density profiles of the water penetrating inside the tablets.

  3. Accuracy of tablet splitting and liquid measurements: an examination of who, what and how.

    PubMed

    Abu-Geras, Dana; Hadziomerovic, Dunja; Leau, Andrew; Khan, Ramzan Nazim; Gudka, Sajni; Locher, Cornelia; Razaghikashani, Maryam; Lim, Lee Yong

    2017-05-01

    To examine factors that might affect the ability of patients to accurately halve tablets or measure a 5-ml liquid dose. Eighty-eight participants split four different placebo tablets by hand and using a tablet splitter, while 85 participants measured 5 ml of water, 0.5% methylcellulose (MC) and 1% MC using a syringe and dosing cup. Accuracy of manipulation was determined by mass measurements. The general population was less able than pharmacy students to break tablets into equal parts, although age, gender and prior experience were insignificant factors. Greater accuracy of tablet halving was observed with tablet splitter, with scored tablets split more equally than unscored tablets. Tablet size did not affect the accuracy of splitting. However, >25% of small scored tablets failed to be split by hand, and 41% of large unscored tablets were split into >2 portions in the tablet splitter. In liquid measurement, the syringe provided more accurate volume measurements than the dosing cup, with higher accuracy observed for the more viscous MC solutions than water. Formulation characteristics and manipulation technique have greater influences on the accuracy of medication modification and should be considered in off-label drug use in vulnerable populations. © 2016 Royal Pharmaceutical Society.

  4. Formulation, characterization and physicochemical evaluation of potassium citrate effervescent tablets.

    PubMed

    Aslani, Abolfazl; Fattahi, Fatemeh

    2013-01-01

    The aim of this study was to design and formulation of potassium citrate effervescent tablet for reduction of calcium oxalate and urate kidney stones in patients suffering from kidney stones. In this study, 13 formulations were prepared from potassium citrate and effervescent base in different concentration. The flowability of powders and granules was studied. Then effervescent tablets were prepared by direct compression, fusion and wet granulation methods. The prepared tablets were evaluated for hardness, friability, effervescent time, pH, content uniformity. To amend taste of formulations, different flavoring agents were used and then panel test was done by using Latin Square method by 30 volunteers. Formulations obtained from direct compression and fusion methods had good flow but low hardness. Wet granulation improves flowability and other physicochemical properties such as acceptable hardness, effervescence time ≤3 minutes, pH<6, friability < 1%, water percentage < 0.5% and accurate content uniformity. In panel test, both of combination flavors; (orange - lemon) and (strawberry - raspberry) had good acceptability. The prepared tablets by wet granulation method using PVP solution had more tablet hardness. It is a reproducible process and suitable to produce granules that are compressed into effervescent tablets due to larger agglomerates.

  5. Release kinetics of papaverine hydrochloride from tablets with different excipients.

    PubMed

    Kasperek, Regina; Polski, Andrzej; Zimmer, Łukasz; Poleszak, Ewa

    2014-01-01

    The influence of excipients on the disintegration times of tablets and the release of papaverine hydrochloride (PAP) from tablets were studied. Ten different formulations of tablets with PAP were prepared by direct powder compression. Different binders, disintegrants, fillers, and lubricants were used as excipients. The release of PAP was carried out in the paddle apparatus using 0.1 N HCl as a dissolution medium. The results of the disintegration times of tablets showed that six formulations can be classified as fast dissolving tablets (FDT). FDT formulations contained Avicel PH 101, Avicel PH 102, mannitol, (3-lactose, PVP K 10, gelatinized starch (CPharmGel), Prosolv Easy Tab, Prosolv SMCC 90, magnesium stearate, and the addition of disintegrants such as AcDiSol and Kollidon CL. Drug release kinetics were estimated by the zero- and first-order, Higuchi release rate, and Korsmeyer-Peppas models. Two formulations of the tablets containing PVP (K10) (10%), CPharmGel (10% and 25%), and Prosolv Easy Tab (44% and 60%) without the addition of a disintegrant were well-fitted to the kinetics models such as the Higuchi and zero-order, which are suitable for controlled- or sustained-release.

  6. Release Kinetics of Papaverine Hydrochloride from Tablets with Different Excipients

    PubMed Central

    Kasperek, Regina; Polski, Andrzej; Zimmer, Łukasz; Poleszak, Ewa

    2014-01-01

    Abstract The influence of excipients on the disintegration times of tablets and the release of papaverine hydrochloride (PAP) from tablets were studied. Ten different formulations of tablets with PAP were prepared by direct powder compression. Different binders, disintegrants, fillers, and lubricants were used as excipients. The release of PAP was carried out in the paddle apparatus using 0.1 N HCl as a dissolution medium. The results of the disintegration times of tablets showed that six formulations can be classified as fast dissolving tablets (FDT). FDT formulations contained Avicel PH 101, Avicel PH 102, mannitol, (3-lactose, PVP K 10, gelatinized starch (CPharmGel), Prosolv Easy Tab, Prosolv SMCC 90, magnesium stearate, and the addition of disintegrants such as AcDiSol and Kollidon CL. Drug release kinetics were estimated by the zero- and first-order, Higuchi release rate, and Korsmeyer-Peppas models. Two formulations of the tablets containing PVP (K10) (10%), CPharmGel (10% and 25%), and Prosolv Easy Tab (44% and 60%) without the addition of a disintegrant were well-fitted to the kinetics models such as the Higuchi and zero-order, which are suitable for controlled- or sustained-release. PMID:25853076

  7. Using Tablet for visual exploration of second-generation sequencing data.

    PubMed

    Milne, Iain; Stephen, Gordon; Bayer, Micha; Cock, Peter J A; Pritchard, Leighton; Cardle, Linda; Shaw, Paul D; Marshall, David

    2013-03-01

    The advent of second-generation sequencing (2GS) has provided a range of significant new challenges for the visualization of sequence assemblies. These include the large volume of data being generated, short-read lengths and different data types and data formats associated with the diversity of new sequencing technologies. This article illustrates how Tablet-a high-performance graphical viewer for visualization of 2GS assemblies and read mappings-plays an important role in the analysis of these data. We present Tablet, and through a selection of use cases, demonstrate its value in quality assurance and scientific discovery, through features such as whole-reference coverage overviews, variant highlighting, paired-end read mark-up, GFF3-based feature tracks and protein translations. We discuss the computing and visualization techniques utilized to provide a rich and responsive graphical environment that enables users to view a range of file formats with ease. Tablet installers can be freely downloaded from http://bioinf.hutton.ac.uk/tablet in 32 or 64-bit versions for Windows, OS X, Linux or Solaris. For further details on the Tablet, contact tablet@hutton.ac.uk.

  8. Modeling picking on pharmaceutical tablets

    NASA Astrophysics Data System (ADS)

    Swaminathan, Shrikant

    Tablets are the most popular solid dosage form in the pharmaceutical industry because they are cheap to manufacture, chemically and mechanically stable and easy to transport and fairly easy to control dosage. Pharmaceutical tableting operations have been around for decades however the process is still not well understood. One of the common problems faced during the production of pharmaceutical tablets by powder compaction is sticking of powder to the punch face, This is known as 'sticking'. A more specialized case of sticking is picking when the powder is pulled away form the compact in the vicinity of debossed features. In the pharmaceutical industry, picking is solved by trial and error which is an expensive, labor intensive and time consuming affair. The objective of this work was to develop, validate, and implement a modeling framework for predicting picking in powder compacts. The model was developed in Abaqus a commercially available finite element package. The resulting model was used to investigate the influence of debossed feature geometry viz. the stroke angle and degree of pre-pick, and, influence of lubricant on picking. (Abstract shortened by ProQuest.).

  9. Hydroxyethyl Pachyman as a novel excipient for sustained-release matrix tablets.

    PubMed

    Zhou, Xiaoju; Wang, Pengyu; Wang, Jiong; Liu, Zhi; Hong, Xuechuan; Xiao, Yuling; Liu, Peng; Hu, Xianming

    2016-12-10

    This paper addressed the application of hydroxyethyl pachyman (HEP) as a novel matrix for sustained - release tablets, using diclofenac sodium (DS) as a model drug. The studies showed the HEP tablets prepared by wet granulation had much slower drug release as compared to those prepared by direct compression. Meanwhile, increasing the percentage of HEP in the formulations caused a decrease in drug release rates. Moreover, DS release from the HEP tablets was much higher at high pH (6.8) than that at low pH (1.2). Morphology studies proved the HEP tablet formed a continuous gel layer with porous inner structure in the dissolution media. Analysis of DS release profiles revealed that diffusion and matrix erosion occurred in simulated intestinal fluid(SIF, pH=6.8) for all the tablets. The experimental results predict HEP has a potential as a hydrophilic matrix in tablets to prolong drug release. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Effect of gel formation on the dissolution behavior of clarithromycin tablets.

    PubMed

    Inukai, Koki; Takiyama, Kei; Noguchi, Shuji; Iwao, Yasunori; Itai, Shigeru

    2017-04-15

    Clarithromycin (CAM) is a macrolide antibiotic that is widely used at clinical sites. We found that release of CAM is suppressed when tablets of CAM were exposed to an external solvent containing carboxylate buffers such as citrate. The suppressed release of CAM can be attributed to the formation of gels on the tablet surfaces, which inhibits penetration of the solvent into the tablet and thus disintegration of the tablets. Delayed disintegration of the tablets was also observed for commercial tablets. This suggests that taking CAM and carboxylates at the same time might be avoided. The crystal structure of CAM citrate reveals that molecular chains of CAM are cross-linked by hydrogen bond between citrate groups in the crystal. The crystal structure indicates that cross-linked CAM chains of the three-dimensional mesh structure might also be formed in high concentration CAM solutions in the presence of carboxylates, resulting in gel formation. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Disintegration of chemotherapy tablets for oral administration in patients with swallowing difficulties.

    PubMed

    Siden, Rivka; Wolf, Matthew

    2013-06-01

    The administration of oral chemotherapeutic drugs can be problematic in patients with swallowing difficulties. Inability to swallow solid dosage forms can compromise compliance and may lead to poor clinical outcome. The current technique of tablet crushing to aid in administration is considered an unsafe practice. By developing a technique to disintegrate tablets in an oral syringe, the risk associated with tablet crushing can be avoided. The purpose of this study was to determine the feasibility of using disintegration in an oral syringe for the administration of oral chemotherapeutic tablets. Eight commonly used oral chemotherapeutic drugs were tested. Tablets were placed in an oral syringe and allowed to disintegrate in tap water. Various volumes and temperatures were tested to identify which combination allows for complete disintegration of the tablet in the shortest amount of time. The oral syringe disintegration method was considered feasible if disintegration occurred in ≤15 min and in ≤20 mL of water and the dispersion passed through an oral syringe tip. The following tablets were shown to disintegrate within 15 min and in <20 mL of water: busulfan, cyclophosphamide 50 mg, dasatinib, imatinib, methotrexate, and thioguanine. For these drugs, drug-specific information pamphlets can be prepared for patient or caregiver use. Mercaptopurine, cyclophosphamide 25 mg, and mitotane tablets did not pass the disintegration test. Disintegrating oral chemotherapeutic tablets in a syringe provides a closed system to administer hazardous drugs and allows for the safe administration of oral chemotherapeutic drugs in a tablet form to patients with swallowing difficulties.

  12. Setting Ideal Lubricant Mixing Time for Manufacturing Tablets by Evaluating Powder Flowability.

    PubMed

    Nakamura, Shohei; Yamaguchi, Saori; Hiraide, Rikiha; Iga, Kumi; Sakamoto, Takatoshi; Yuasa, Hiroshi

    2017-10-01

    We investigated the effectiveness of using Carr's flowability index (FI) and practical angle of internal friction (Φ) as indexes for setting the target Mg-St mixing time needed for preparing tablets with the target physical properties. We used FI as a measure of flowability under non-loaded conditions, and Φ as a measure of flowability under loaded conditions for pharmaceutical powders undergoing direct compression with varying concentrations of Mg-St and mixing times. We evaluated the relationship between Mg-St mixing conditions and pharmaceutical powder flowability, analyzed the correlation between the physical properties of the tablets (i.e., tablet weight variation, drug content uniformity, hardness, friability, and disintegration time of tablets prepared using the pharmaceutical powder), and studied the effect of Mg-St mixing conditions and pharmaceutical powder flowability on tablet properties. Mg-St mixing time highly correlated with pharmaceutical powder FI (R 2  = 0.883) while Mg-St concentration has low correlation with FI, and FI highly correlated with the physical properties of the tablet (R 2 values: weight variation 0.509, drug content variation 0.314, hardness 0.525, friability 0.477, and disintegration time 0.346). Therefore, using pharmaceutical powder FI as an index could enable prediction of the physical properties of a tablet without the need for tableting, and setting the Mg-St mixing time by using pharmaceutical powder FI could enable preparation of tablets with the target physical properties. Thus, the FI of the intermediate product (i.e., pharmaceutical powder) is an effective index for controlling the physical properties of the finished tablet.

  13. Dosage form design and in vitro/in vivo evaluation of cevimeline extended-release tablet formulations.

    PubMed

    Tajiri, Shinichiro; Kanamaru, Taro; Kamada, Makoto; Makoto, Kamada; Konno, Tsutomu; Nakagami, Hiroaki

    2010-01-04

    The objective of the present work is to develop an extended-release dosage form of cevimeline. Two types of extended-release tablets (simple matrix tablets and press-coated tablets) were prepared and their potential as extended-release dosage forms were assessed. Simple matrix tablets have a large amount of hydroxypropylcellulose as a rate-controlling polymer and the matrix is homogeneous throughout the tablet. The press-coated tablets consisted of a matrix core tablet, which was completely surrounded by an outer shell containing a large amount of hydroxypropylcellulose. The simple matrix tablets could not sustain the release of cevimeline effectively. In contrast, the press-coated tablets showed a slower dissolution rate compared with simple matrix tablets and the release curve was nearly linear. The dissolution of cevimeline from the press-coated tablets was not markedly affected by the pH of the dissolution medium or by a paddle rotating speed over the range of 50-200 rpm. Furthermore, cevimeline was constantly released from the press-coated tablets in the gastrointestinal tract and the steady-state plasma drug levels were maintained in beagle dogs. These results suggested that the designed PC tablets have a potential for extended-release dosage forms.

  14. Bioequivalence of saxagliptin/metformin extended-release (XR) fixed-dose combination tablets and single-component saxagliptin and metformin XR tablets in healthy adult Chinese subjects.

    PubMed

    Gummesson, Anders; Li, Haiyan; Gillen, Michael; Xu, John; Niazi, Mohammad; Hirshberg, Boaz

    2014-11-01

    As compared with individual tablets, saxagliptin/metformin extended-release (XR) fixed-dose combination (FDC) tablets offer the potential for increased patient compliance with the convenience of once daily dosing. The aim of the present study was to show that the FDC of saxagliptin and metformin XR is bioequivalent to co-administration of the individual components when given to Chinese subjects residing in China. This was a randomized, open-label, single-dose, two-period, cross-over pharmacokinetic study in two cohorts of healthy adult Chinese male subjects (n = 32 in each cohort) under fed conditions. In cohort 1, the pharmacokinetic properties of a saxagliptin/metformin XR 5/500 mg FDC tablet were compared with those of co-administration of a 5 mg saxagliptin tablet and a 500 mg metformin XR tablet. In cohort 2, the pharmacokinetic properties of a saxagliptin/metformin XR 5/1,000 mg FDC tablet were compared with those of co-administration of a 5 mg saxagliptin tablet and 2 × 500 mg metformin XR tablets. The two cohorts were independent of each other with respect to treatment and results. The pharmacokinetic properties of the active metabolite of saxagliptin (5-hydroxy-saxagliptin), as well as the safety and tolerability of each treatment, were also evaluated. For both cohorts, saxagliptin and metformin in the FDCs were bioequivalent to the individual components, as the limits of the 90 % confidence intervals of the geometric least squares mean ratios were contained within the 80-125 % bioequivalence limits for the area under the plasma concentration-time curve parameters and within the 70-143 % bioequivalence limits for the maximum plasma concentration. Similar exposures of 5-hydroxy-saxagliptin were observed with the two treatment regimens within each cohort. Co-administration of saxagliptin and metformin XR was generally safe and well tolerated as the FDCs or as individual tablets. Saxagliptin/metformin XR 5/500 mg and saxagliptin/metformin XR 5

  15. Resveratrol cocrystals with enhanced solubility and tabletability.

    PubMed

    Zhou, Zhengzheng; Li, Wanying; Sun, Wei-Jhe; Lu, Tongbu; Tong, Henry H Y; Sun, Changquan Calvin; Zheng, Ying

    2016-07-25

    Two new 1:1 cocrystals of resveratrol (RES) with 4-aminobenzamide (RES-4ABZ) and isoniazid (RES-ISN) were synthesized by liquid assisted grinding (LAG) and rapid solvent removal (RSR) methods using ethanol as solvent. Their physiochemical properties were characterized using PXRD, DSC, solid state and solution NMR, FT-IR, and HPLC. Pharmaceutically relevant properties, including tabletability, solubility, intrinsic dissolution rate, and hygroscopicity, were evaluated. Temperature-composition phase diagram for RES-ISN cocrystal system was constructed from DSC data. Both cocrystals show higher solubility than resveratrol over a broad range of pH. They are phase stable and non-hygroscopic even under high humidity conditions. Importantly, both cocrystals exhibit improved solubility and tabletability compared with RES, which make them more suitable candidates for tablet formulation development. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. A study on maize proteins as a potential new tablet excipient.

    PubMed

    Georget, Dominique M R; Barker, Susan A; Belton, Peter S

    2008-06-01

    This investigation has examined the use of zein proteins from maize as the major component in oral controlled-release tablets, such formulations often being required to improve patient compliance. Tablets containing ground zein proteins, calcium hydrogen orthophosphate, polyvinyl pyrrolidone, theophylline and magnesium stearate were produced by wet granulation and compression on a single station tablet press and were compared to directly compressed tablets based on zein proteins, calcium hydrogen orthophosphate and theophylline. Non invasive techniques such as Fourier Transform infrared spectroscopy and Fourier Transform Raman spectroscopy were employed to investigate any changes in the secondary structure of zein proteins during tablet production. Random coils, alpha helices and beta sheets predominated and their relative content remained unaffected during grinding, wet granulation and compression, indicating that formulations based on zeins will be robust, i.e. insensitive to minor changes in the production conditions. Drug release from the tablets was studied using a standard pharmacopoeial dissolution test. Dissolution profiles in water, 0.1M HCl (pH=1) and phosphate buffer (pH=6.8) show that only a limited amount of theophylline was released after 4.5h, suggesting that zein proteins could act as a potential vehicle for oral controlled drug release. Analysis of the theophylline release profiles using the Peppas and Sahlin model reveals that diffusion and polymer relaxation occurred in acidic (pH=1) and buffered (pH=6.8) conditions for wet granulated tablets, whereas diffusion was predominant in directly compressed tablets. In conclusion, the present study has shown that zeins can be successfully used as a pharmaceutical excipient, and in particular as a matrix in monolithic controlled release tablets.

  17. Tableau Economique: Teaching Economics with a Tablet Computer

    ERIC Educational Resources Information Center

    Scott, Robert H., III

    2011-01-01

    The typical method of instruction in economics is chalk and talk. Economics courses often require writing equations and drawing graphs and charts, which are all best done in freehand. Unlike static PowerPoint presentations, tablet computers create dynamic nonlinear presentations. Wireless technology allows professors to write on their tablets and…

  18. Gluten and Aluminum Content in Synthroid® (Levothyroxine Sodium Tablets).

    PubMed

    Espaillat, Ramon; Jarvis, Michael F; Torkelson, Cory; Sinclair, Brent

    2017-07-01

    Inquiries from healthcare providers and patients about the gluten and aluminum content of Synthroid ® (levothyroxine sodium tablets) have increased. The objective of this study was to measure and evaluate the gluten content of the raw materials used in the manufacturing of Synthroid. Additionally, this study determined the aluminum content in different strengths of Synthroid tablets by estimating the amount of aluminum in the raw materials used in the manufacturing of Synthroid. Gluten levels of three lots of the active pharmaceutical ingredient (API) and one lot of each excipient from different vendors were examined. The ingredients in all current Synthroid formulations (strengths) were evaluated for their quantity of aluminum. Gluten concentrations were below the lowest limit of detection (<3.0 ppm) for all tested lots of the API and excipients of Synthroid tablets. Aluminum content varied across tablet strengths (range 19-137 µg/tablet). Gluten levels of the API and excipients were found to be below the lowest level of detection and are considered gluten-free based on the US Food and Drug Administration (FDA) definition for food products. Across the various tablet strengths of Synthroid, the maximum aluminum levels were well below the FDA-determined minimal risk level for chronic oral aluminum exposure (1 mg/kg/day). These data demonstrate that Synthroid tablets are not a source for dietary gluten and are a minimal source of aluminum. AbbVie Inc.

  19. Evaluation of tablet computers for visual function assessment.

    PubMed

    Bodduluri, Lakshmi; Boon, Mei Ying; Dain, Stephen J

    2017-04-01

    Recent advances in technology and the increased use of tablet computers for mobile health applications such as vision testing necessitate an understanding of the behavior of the displays of such devices, to facilitate the reproduction of existing or the development of new vision assessment tests. The purpose of this study was to investigate the physical characteristics of one model of tablet computer (iPad mini Retina display) with regard to display consistency across a set of devices (15) and their potential application as clinical vision assessment tools. Once the tablet computer was switched on, it required about 13 min to reach luminance stability, while chromaticity remained constant. The luminance output of the device remained stable until a battery level of 5%. Luminance varied from center to peripheral locations of the display and with viewing angle, whereas the chromaticity did not vary. A minimal (1%) variation in luminance was observed due to temperature, and once again chromaticity remained constant. Also, these devices showed good temporal stability of luminance and chromaticity. All 15 tablet computers showed gamma functions approximating the standard gamma (2.20) and showed similar color gamut sizes, except for the blue primary, which displayed minimal variations. The physical characteristics across the 15 devices were similar and are known, thereby facilitating the use of this model of tablet computer as visual stimulus displays.

  20. Stabilization Mechanism of Roxithromycin Tablets under Gastric pH Conditions.

    PubMed

    Inukai, Koki; Noguchi, Shuji; Kimura, Shin-Ichiro; Itai, Shigeru; Iwao, Yasunori

    2018-05-31

    Macrolide antibiotics are widely used at clinical sites. Clarithromycin (CAM), a 14-membered macrolide antibiotic, was reported to gelate under acidic conditions. Gelation allows oral administration of acid-sensitive CAM without enteric coating by hindering the penetration of gastric fluid into CAM tablets. However, it is unknown whether this phenomenon occurs in other macrolide antibiotics. In this study, we examined the gelation ability of three widely used macrolide antibiotics, roxithromycin (RXM), erythromycin A (EM), and azithromycin (AZM). The results indicated that not only CAM but also RXM gelated under acidic conditions. EM and AZM did not gelate under the same conditions. Gelation of RXM delayed the disintegration of the tablet and release of RXM from the tablet. Disintegration and release were also delayed in commercial RXM tablets containing disintegrants. This study showed that two of the four macrolides gelated, which affects tablet disintegration and dissolution and suggests that this phenomenon might also occur in other macrolides. Copyright © 2018. Published by Elsevier Inc.

  1. Demonstration of pharmaceutical tablet coating process by injection molding technology.

    PubMed

    Puri, Vibha; Brancazio, David; Harinath, Eranda; Martinez, Alexander R; Desai, Parind M; Jensen, Keith D; Chun, Jung-Hoon; Braatz, Richard D; Myerson, Allan S; Trout, Bernhardt L

    2018-01-15

    We demonstrate the coating of tablets using an injection molding (IM) process that has advantage of being solvent free and can provide precision coat features. The selected core tablets comprising 10% w/w griseofulvin were prepared by an integrated hot melt extrusion-injection molding (HME-IM) process. Coating trials were conducted on a vertical injection mold machine. Polyethylene glycol and polyethylene oxide based hot melt extruded coat compositions were used. Tablet coating process feasibility was successfully demonstrated using different coating mold designs (with both overlapping and non-overlapping coatings at the weld) and coat thicknesses of 150 and 300 μm. The resultant coated tablets had acceptable appearance, seal at the weld, and immediate drug release profile (with an acceptable lag time). Since IM is a continuous process, this study opens opportunities to develop HME-IM continuous processes for transforming powder to coated tablets. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Research data collection methods: from paper to tablet computers.

    PubMed

    Wilcox, Adam B; Gallagher, Kathleen D; Boden-Albala, Bernadette; Bakken, Suzanne R

    2012-07-01

    Primary data collection is a critical activity in clinical research. Even with significant advances in technical capabilities, clear benefits of use, and even user preferences for using electronic systems for collecting primary data, paper-based data collection is still common in clinical research settings. However, with recent developments in both clinical research and tablet computer technology, the comparative advantages and disadvantages of data collection methods should be determined. To describe case studies using multiple methods of data collection, including next-generation tablets, and consider their various advantages and disadvantages. We reviewed 5 modern case studies using primary data collection, using methods ranging from paper to next-generation tablet computers. We performed semistructured telephone interviews with each project, which considered factors relevant to data collection. We address specific issues with workflow, implementation and security for these different methods, and identify differences in implementation that led to different technology considerations for each case study. There remain multiple methods for primary data collection, each with its own strengths and weaknesses. Two recent methods are electronic health record templates and next-generation tablet computers. Electronic health record templates can link data directly to medical records, but are notably difficult to use. Current tablet computers are substantially different from previous technologies with regard to user familiarity and software cost. The use of cloud-based storage for tablet computers, however, creates a specific challenge for clinical research that must be considered but can be overcome.

  3. Analysis of drug content and weight uniformity for half-tablets of 6 commonly split medications.

    PubMed

    Hill, Shaynan W; Varker, Andrew S; Karlage, Kelly; Myrdal, Paul B

    2009-04-01

    Cost savings can be achieved with the practice of tablet splitting. Previous research has shown weight nonuniformity within tablet halves. However, limited research to date has found that the potential dose inaccuracy resulting from splitting tablets does not significantly affect clinical outcomes. To determine the drug content and weight in split half-tablets of 6 commonly split medications using drug assay analysis. This study was performed by 2 fourth-year pharmacy students using 30 randomly selected tablets of each of the following 6 medications: warfarin sodium 5 milligrams (mg), simvastatin 80 mg, metoprolol succinate 200 mg, metoprolol tartrate 25 mg, citalopram 40 mg, and lisinopril 40 mg. A randomly selected half of the tablets were split by a single pharmacy student using a tablet cutter, and the remaining tablets were kept whole. Drug content was analyzed for 15 whole tablets and 30 half-tablets for each of the 6 drugs using high performance liquid chromatography, an analytical tool used to identify and quantify substances in solution. Drug content uniformity was assessed by comparing drug content within half-tablets with one-half of the drug content mean found for all whole tablets in the sample. Weight uniformity was assessed by comparing half-tablet weights, as determined by a Mettler analytical balance, with one-half of the mean weight for whole tablets in the sample. The percentages by which each whole tablet's or half-tablet's drug content and weight differed from sample mean values were compared with proxy United States Pharmacopeia (USP) specification ranges for drug content (95%-105% for warfarin sodium and 90%-110% for the other 5 drugs). Additionally, these outcomes were compared for nonscored versus scored tablets. The percent relative standard deviation (%RSD, ratio of the standard deviation to the mean), a commonly used measure of the repeatability and precision of assays used to analyze drug content, was also calculated in order to

  4. Equivalency of Paper versus Tablet Computer Survey Data

    ERIC Educational Resources Information Center

    Ravert, Russell D.; Gomez-Scott, Jessica; Donnellan, M. Brent

    2015-01-01

    Survey responses collected via paper surveys and computer tablets were compared to test for differences between those methods of obtaining self-report data. College students (N = 258) were recruited in public campus locations and invited to complete identical surveys on either paper or iPad tablet. Only minor homogeneity differences were found…

  5. Enhancing the Classroom Experience: Instructor Use of Tablets

    ERIC Educational Resources Information Center

    Cummings, Jeff; Hill, Stephen

    2015-01-01

    Instructors continually search for innovative approaches to interact with and engage students in the classroom. The tablet offers a potential innovation for this purpose. Tablet devices from Apple, Microsoft, and other hardware vendors have overcome many of the challenges of the past (e.g. cost and limited applications) to become useful tools for…

  6. Continuous direct compression as manufacturing platform for sustained release tablets.

    PubMed

    Van Snick, B; Holman, J; Cunningham, C; Kumar, A; Vercruysse, J; De Beer, T; Remon, J P; Vervaet, C

    2017-03-15

    This study presents a framework for process and product development on a continuous direct compression manufacturing platform. A challenging sustained release formulation with high content of a poorly flowing low density drug was selected. Two HPMC grades were evaluated as matrix former: standard Methocel CR and directly compressible Methocel DC2. The feeding behavior of each formulation component was investigated by deriving feed factor profiles. The maximum feed factor was used to estimate the drive command and depended strongly upon the density of the material. Furthermore, the shape of the feed factor profile allowed definition of a customized refill regime for each material. Inline NIRs was used to estimate the residence time distribution (RTD) in the mixer and monitor blend uniformity. Tablet content and weight variability were determined as additional measures of mixing performance. For Methocel CR, the best axial mixing (i.e. feeder fluctuation dampening) was achieved when an impeller with high number of radial mixing blades operated at low speed. However, the variability in tablet weight and content uniformity deteriorated under this condition. One can therefore conclude that balancing axial mixing with tablet quality is critical for Methocel CR. However, reformulating with the direct compressible Methocel DC2 as matrix former improved tablet quality vastly. Furthermore, both process and product were significantly more robust to changes in process and design variables. This observation underpins the importance of flowability during continuous blending and die-filling. At the compaction stage, blends with Methocel CR showed better tabletability driven by a higher compressibility as the smaller CR particles have a higher bonding area. However, tablets of similar strength were achieved using Methocel DC2 by targeting equal porosity. Compaction pressure impacted tablet properties and dissolution. Hence controlling thickness during continuous manufacturing of

  7. Tablet compression tooling - Impact of punch face edge modification.

    PubMed

    Anbalagan, Parthiban; Heng, Paul Wan Sia; Liew, Celine Valeria

    2017-05-30

    The influence of punch face edge geometry modification on tablet compression and the properties of the resultant tablets produced on a rotary press were investigated. The results revealed that tablets produced from the punches with radius edge face geometry consistently displayed better physical quality; higher tensile strength and lower capping tendency. Modification of the angled edge of the bevel face to the curved edge of the radius face, enabled deeper punch penetration in the die cavity during the compression cycle, bringing about greater compact densification. Improved die fill packing increased interparticulate bond formation and helped to dissipate destructive elasticity within the compact, consequently reduced tablet expansion during the decompression phase. The positive impact of punch face edge modification was also more noticeable at a higher turret speed. The application of the precompression force along with dwell time extension amplified the tableting performance of radius edge punch face design to a greater extent when compared to bevel edge punch face design. This could be attributed to the enhanced packing efficiency at both precompression and main compression stages. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Evaluation of matrix type mucoadhesive tablets containing indomethacin for buccal application.

    PubMed

    Ikeuchi-Takahashi, Yuri; Sasatsu, Masanaho; Onishi, Hiraku

    2013-09-10

    Nonsteroidal anti-inflammatory drugs (NSAIDs) are administered for pain relief from oral mucositis. However, the systemic administration of NSAIDs is limited due to systemic side effects. To avoid these side effects and treat local lesions effectively, a matrix type mucoadhesive tablet was developed. A mixture of hard fat, ethylcellulose (EC) and polyethylene glycol (PEG) was used as a matrix base, and indomethacin (IMC) was used as the principal agent. In tablets consisting of hard fat, EC and IMC, the drug release was sustained. In tablets consisting of hard fat, EC, considerable amounts of PEG and IMC, the drug release was relatively increased and IMC existed as the molecular phase or in an amorphous state. The in vitro adhesive force of the tablets consisting of hard fat, EC, considerable amounts of PEG and IMC was significantly increased as compared with the tablets consisting of hard fat and IMC. A significantly high tissue concentration and significantly low plasma concentration were observed after buccal administration of this matrix type mucoadhesive tablet as compared with that after oral administration of IMC. Thus, the matrix type mucoadhesive tablet has good potential as a preparation for the treatment of pain due to oral aphtha. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Pharmacokinetic Profiles of Ticagrelor Orodispersible Tablets in Healthy Western and Japanese Subjects.

    PubMed

    Teng, Renli; Hammarberg, Maria; Carlson, Glenn F; Bokelund-Singh, Sara; Ruderfelt, Terese; Blychert, Eva

    2017-11-01

    Ticagrelor is an antiplatelet agent for patients with acute coronary syndrome or a history of myocardial infarction. Two studies compared pharmacokinetic profiles of orodispersible (OD) ticagrelor tablets versus immediate-release (IR) tablets in Western and Japanese subjects. Both studies were open-label, randomized, crossover, single-center trials. Thirty-six healthy subjects (94% white, 6% other race; Western study NCT02400333) and 42 Japanese healthy subjects (Japanese study NCT02436577) received a single 90-mg ticagrelor dose as an OD tablet [with/without water, and via a nasogastric tube (Western study only)], and an IR tablet; washout between treatments was ≥7 days. Assessments included ticagrelor and AR-C124910XX (active metabolite) plasma concentrations for pharmacokinetic analyses, and safety evaluations. In the Western study, the 90% confidence intervals (CIs) of the geometric mean ratios (GMRs) for ticagrelor and AR-C124910XX maximum plasma concentration (C max ) and area under the plasma concentration-time curve (AUC) were within the acceptance interval (80%-125%) for OD tablets (with/without water, via a nasogastric tube) versus the IR tablet; except for an ~15% lowering of ticagrelor C max (90% CI: 76.77%-93.78%) for the OD tablet taken with water. In the Japanese study, 90% CIs of the GMRs for AUC and C max of both ticagrelor and AR-C124910XX were all within the acceptance intervals for the OD (with/without water) versus IR tablet. No new safety issues were identified. Ticagrelor administered as an OD tablet to Western (without water, and via a nasogastric tube) and Japanese (with/without water) subjects was bioequivalent to the IR tablet.

  10. Security Approaches in Using Tablet Computers for Primary Data Collection in Clinical Research

    PubMed Central

    Wilcox, Adam B.; Gallagher, Kathleen; Bakken, Suzanne

    2013-01-01

    Next-generation tablets (iPads and Android tablets) may potentially improve the collection and management of clinical research data. The widespread adoption of tablets, coupled with decreased software and hardware costs, has led to increased consideration of tablets for primary research data collection. When using tablets for the Washington Heights/Inwood Infrastructure for Comparative Effectiveness Research (WICER) project, we found that the devices give rise to inherent security issues associated with the potential use of cloud-based data storage approaches. This paper identifies and describes major security considerations for primary data collection with tablets; proposes a set of architectural strategies for implementing data collection forms with tablet computers; and discusses the security, cost, and workflow of each strategy. The paper briefly reviews the strategies with respect to their implementation for three primary data collection activities for the WICER project. PMID:25848559

  11. Security approaches in using tablet computers for primary data collection in clinical research.

    PubMed

    Wilcox, Adam B; Gallagher, Kathleen; Bakken, Suzanne

    2013-01-01

    Next-generation tablets (iPads and Android tablets) may potentially improve the collection and management of clinical research data. The widespread adoption of tablets, coupled with decreased software and hardware costs, has led to increased consideration of tablets for primary research data collection. When using tablets for the Washington Heights/Inwood Infrastructure for Comparative Effectiveness Research (WICER) project, we found that the devices give rise to inherent security issues associated with the potential use of cloud-based data storage approaches. This paper identifies and describes major security considerations for primary data collection with tablets; proposes a set of architectural strategies for implementing data collection forms with tablet computers; and discusses the security, cost, and workflow of each strategy. The paper briefly reviews the strategies with respect to their implementation for three primary data collection activities for the WICER project.

  12. Preparation of monolithic osmotic pump system by coating the indented core tablet.

    PubMed

    Liu, Longxiao; Che, Binjie

    2006-10-01

    A method for the preparation of monolithic osmotic pump tablet was obtained by coating the indented core tablet compressed by the punch with a needle. Atenolol was used as the model drug, sodium chloride as osmotic agent and polyethylene oxide as suspending agent. Ethyl cellulose was employed as semipermeable membrane containing polyethylene glycol 400 as plasticizer for controlling membrane permeability. The formulation of atenolol osmotic pump tablet was optimized by orthogonal design and evaluated by similarity factor (f2). The optimal formulation was evaluated in various release media and agitation rates. Indentation size of core tablet hardly affected drug release in the range of (1.00-1.14) mm. The optimal osmotic tablet was found to be able to deliver atenolol at an approximately constant rate up to 24h, independent of both release media and agitation rate. The method that is simplified by coating the indented core tablet with the elimination of laser drilling may be promising in the field of the preparation of osmotic pump tablet.

  13. Formulation, Characterization and Physicochemical Evaluation of Potassium Citrate Effervescent Tablets

    PubMed Central

    Aslani, Abolfazl; Fattahi, Fatemeh

    2013-01-01

    Purpose: The aim of this study was to design and formulation of potassium citrate effervescent tablet for reduction of calcium oxalate and urate kidney stones in patients suffering from kidney stones. Methods: In this study, 13 formulations were prepared from potassium citrate and effervescent base in different concentration. The flowability of powders and granules was studied. Then effervescent tablets were prepared by direct compression, fusion and wet granulation methods. The prepared tablets were evaluated for hardness, friability, effervescent time, pH, content uniformity. To amend taste of formulations, different flavoring agents were used and then panel test was done by using Latin Square method by 30 volunteers. Results: Formulations obtained from direct compression and fusion methods had good flow but low hardness. Wet granulation improves flowability and other physicochemical properties such as acceptable hardness, effervescence time ≤3 minutes, pH<6, friability < 1%, water percentage < 0.5% and accurate content uniformity. In panel test, both of combination flavors; (orange - lemon) and (strawberry - raspberry) had good acceptability. Conclusion: The prepared tablets by wet granulation method using PVP solution had more tablet hardness. It is a reproducible process and suitable to produce granules that are compressed into effervescent tablets due to larger agglomerates. PMID:24312839

  14. Highly anisotropic conductivity of tablets pressed from polyaniline-montmorillonite nanocomposite

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tokarský, Jonáš, E-mail: jonas.tokarsky@vsb.cz; IT4Innovations Centre of Excellence, VŠB-TU Ostrava, 17. listopadu 15/2172, 708 33 Ostrava—Poruba; Kulhánková, Lenka

    2016-03-15

    Highlights: • Montmorillonite (MMT) can be intercalated with polyaniline (PANI) chains. • Tablets pressed from PANI/MMT exhibit high anisotropy in electrical conductivity. • Pressure 28MPa is sufficient to reach the anisotropy. • Tablets pressed from pure PANI also exhibit anisotropy in electrical conductivity. - Abstract: Polyaniline-montmorillonite nanocomposite was prepared from anilinium sulfate (precursor) and ammonium peroxodisulfate (oxidizing agent) using simple one-step method. The resulting nanocomposite obtained in powder form has been pressed into tablets using various compression pressures (28–400 MPa). Electrical conductivities of tablets in two perpendicular directions, i.e. direction parallel with the main surface of tablet (σ=) and inmore » orthogonal direction (σ⊥), and corresponding anisotropy factors (i.e., the ratio σ=/σ⊥) have been studied in dependence on compression pressure used during the preparation. Polyaniline-montmorillonite nanocomposite was characterized using X-ray diffraction analysis, raman spectroscopy, transmission electron microscopy, thermogravimetric analysis and molecular modeling which led to the understanding of the internal structure. Measurement of hardness performed on pressed tablets has been also involved. Taking into account the highest value of anisotropy factor reached (σ=/σ⊥ = 490), present study shows a chance to design conductors with nearly two-dimensional conductivity.« less

  15. Protecting Investments: Third-Party Warranty Coverage for Tablets

    ERIC Educational Resources Information Center

    Sands, Austin

    2012-01-01

    A year ago, only a handful of K-12 schools and universities had integrated tablets into their curricula. Today, not one week passes with out another iPad rollout announcement. The reasons that schools use tablets are as varied as the schools themselves. Hawaii Preparatory Academy uses iPads to encourage budding physicists, linguists, and…

  16. The Tablet PC for Faculty: A Pilot Project

    ERIC Educational Resources Information Center

    Weitz, Rob R.; Wachsmuth, Bert; Mirliss, Danielle

    2006-01-01

    This paper describes a pilot project with the purpose of evaluating the usefulness of tablet PCs for university professors. The focus is on the value of tablets primarily with respect to teaching and learning (and not for research or administrative work). Sixty-four professors, distributed across the various schools of a university, were provided…

  17. 21 CFR 520.1242b - Levamisole hydrochloride tablet or oblet (bolus).

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Levamisole hydrochloride tablet or oblet (bolus... § 520.1242b Levamisole hydrochloride tablet or oblet (bolus). (a) Chemical name. (-)-2,3,5,6-Tetrahydro... using in severely debilitated animals. (2) It is used in a tablet for sheep as follows: (i) Amount. 0...

  18. Optimization of Premix Powders for Tableting Use.

    PubMed

    Todo, Hiroaki; Sato, Kazuki; Takayama, Kozo; Sugibayashi, Kenji

    2018-05-08

    Direct compression is a popular choice as it provides the simplest way to prepare the tablet. It can be easily adopted when the active pharmaceutical ingredient (API) is unstable in water or to thermal drying. An optimal formulation of preliminary mixed powders (premix powders) is beneficial if prepared in advance for tableting use. The aim of this study was to find the optimal formulation of the premix powders composed of lactose (LAC), cornstarch (CS), and microcrystalline cellulose (MCC) by using statistical techniques. Based on the "Quality by Design" concept, a (3,3)-simplex lattice design consisting of three components, LAC, CS, and MCC was employed to prepare the model premix powders. Response surface method incorporating a thin-plate spline interpolation (RSM-S) was applied for estimation of the optimum premix powders for tableting use. The effect of tablet shape identified by the surface curvature on the optimization was investigated. The optimum premix powder was effective when the premix was applied to a small quantity of API, although the function of premix was limited in the case of the formulation of large amount of API. Statistical techniques are valuable to exploit new functions of well-known materials such as LAC, CS, and MCC.

  19. Comparison of breaking tests for the characterization of the interfacial strength of bilayer tablets.

    PubMed

    Castrati, Luca; Mazel, Vincent; Busignies, Virginie; Diarra, Harona; Rossi, Alessandra; Colombo, Paolo; Tchoreloff, Pierre

    2016-11-20

    The bilayer tableting technology is gaining more acceptance in the drug industry, due to its ability to improve the drug delivery strategies. It is currently assessed by the European Pharmacopoeia, that the mechanical strength of tablets can be evaluated using a diametral breaking tester. This device applies a force diametrically, and records the tablet breaking point. This approach has been used to measure the structural integrity of single layer tablets as well as bilayer (and multi-layer) tablets. The latter ones, however, have a much complex structure. Therefore, testing a bilayer tablet with the currently used breaking test methodology might not be appropriate. The aim of this work was to compare results from several tests that have been proposed to quantify the interfacial strength of bilayer tablets. The obtained results would provide an indication on which tests are appropriate to evaluate the robustness of a bilayer tablet. Bilayer tablets were fabricated using a model formulation: Microcrystalline Cellulose (MCC) for the first layer, and spray dried lactose (SDLac) as second layer. Each set of tablets were tested using the following tests: Diametral Test, Shear Test and Indentation Test. The tablets were examined before and after the breaking test using Scanning Electron Microscopy (SEM). When a bilayer tablet was subjected to shearing or indentation, it showed signs of clear delamination. Differently, using the diametral test system, the tablets showed no clear difference, before and after the testing. However, when examining each layer via SEM, it was clear that a fracture occurred in the layer made of SDLac. Thus, the diametral test is a measure of the strength of one of the two layers and therefore it is not suited to test the mechanical strength of bilayer tablets. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Effect of Touch Screen Tablet Use on Fine Motor Development of Young Children.

    PubMed

    Lin, Ling-Yi; Cherng, Rong-Ju; Chen, Yung-Jung

    2017-10-20

    To investigate the effects of touch-screen tablet use on the fine motor development of preschool children without developmental delay. 40 children who used a touch-screen tablet more 60 minutes per week for at least 1 month received a 24-week home fine motor activity program using a touch-screen-tablet. 40 children matched for age (mean = 61.0 months) and sex who did not meet the criteria for previous tablet use received a 24-week program consisting of manual play activities. Motor performance was measured using the Bruininks-Oseretsky Test of Motor Proficiency. The two-factor mixed design ANOVA was used to compare performance of the touch-screen tablet and non-touch-screen tablet groups. Pretest analysis showed no group differences in motor performance and pinch strength. At posttest, children in the nontouch-screen-tablet group made significantly greater changes in fine motor precision (p < 0.001), fine motor integration (p = 0.008), and manual dexterity (p = 0.003). Using a touch screen tablet extensively might be disadvantageous for the fine motor development of preschool children.

  1. Stability of cyanocobalamin in sugar-coated tablets.

    PubMed

    Ohmori, Shinji; Kataoka, Masumi; Koyama, Hiroyoshi

    2007-06-07

    The purpose of this study was to clarify the stability of cyanocobalamin (VB(12)-CN) in sugar-coated tablets containing fursultiamine hydrochloride (TTFD-HCl), riboflavin (VB(2)), and pyridoxine hydrochloride (VB(6)), and to identify the factors affecting the stability of VB(12)-CN in these sugar-coated tablets. The stability of VB(12)-CN was investigated using high-performance liquid chromatography while decomposition was evaluated kinetically. The decomposition of VB(12)-CN in sugar-coated tablets with high equilibrium relative humidity (more than 60%) under closed conditions showed complex kinetics and followed an Avrami-Erofe'ev equation, which expresses a random nucleation (two-dimensional growth of nuclei) model. We showed that equilibrium relative humidity, the incorporation of VB(2) and VB(6), and sugar coating, are the main factors influencing decomposition and that these factors cause the complex decomposition kinetics.

  2. Evaluating Tablet Computers as a Survey Tool in Rural Communities

    PubMed Central

    Newell, Steve M.; Logan, Henrietta L.; Guo, Yi; Marks, John G.; Shepperd, James A.

    2015-01-01

    Purpose Although tablet computers offer advantages in data collection over traditional paper-and-pencil methods, little research has examined whether the 2 formats yield similar responses, especially with underserved populations. We compared the 2 survey formats and tested whether participants’ responses to common health questionnaires or perceptions of usability differed by survey format. We also tested whether we could replicate established paper-and-pencil findings via tablet computer. Methods We recruited a sample of low-income community members living in the rural southern United States. Participants were 170 residents (black = 49%; white = 36%; other races and missing data = 15%) drawn from 2 counties meeting Florida’s state statutory definition of rural with 100 persons or fewer per square mile. We randomly assigned participants to complete scales (Center for Epidemiologic Studies Depression Inventory and Regulatory Focus Questionnaire) along with survey format usability ratings via paper-and-pencil or tablet computer. All participants rated a series of previously validated posters using a tablet computer. Finally, participants completed comparisons of the survey formats and reported survey format preferences. Findings Participants preferred using the tablet computer and showed no significant differences between formats in mean responses, scale reliabilities, or in participants’ usability ratings. Conclusions Overall, participants reported similar scales responses and usability ratings between formats. However, participants reported both preferring and enjoying responding via tablet computer more. Collectively, these findings are among the first data to show that tablet computers represent a suitable substitute among an underrepresented rural sample for paper-and-pencil methodology in survey research. PMID:25243953

  3. An Initial Evaluation of Tablet Devices & What Are the Next Steps?

    ERIC Educational Resources Information Center

    McKillen, Tracey

    2016-01-01

    This paper describes an evaluation of tablet devices for a Graduate Entry Medical School (GEMS). The purpose of this evaluation is to assess what type of tablet device could meet the needs of a GEMS student. GEMS requirements for the evaluation include; using the tablet device to replace paper teaching resources in lectures and tutorials and…

  4. Role of Water Sorption in Tablet Crushing Strength, Disintegration, and Dissolution.

    PubMed

    Sacchetti, M; Teerakapibal, R; Kim, K; Elder, E J

    2017-08-01

    Drugs formulated as tablets are subjected to accelerated stability conditions with the goal of identifying a stable formulation that will exhibit a sufficiently long shelf life. Water sorption at a condition such as 40°C/75% RH can result in significant changes in tablet properties such as a decrease in dissolution rate, the cause of which may be difficult to interpret, given the complex nature of ingredients and their interactions in a tablet. In this research, three drugs, displaying a wide range of physicochemical properties, were formulated with commonly used diluents, disintegrants, and binders, using a design of experiments approach. The tablets were stored at accelerated conditions and assessed for content, dissolution, disintegration, and crushing strength, as well as other properties. The research demonstrated many water-induced effects in tablet properties. Due to the experimental design approach that revealed many interactions, it was possible to interpret all of the changes observed in tablet crushing strength, disintegration, and dissolution for the drugs using a common set of physical principles. Specifically, the relevant factors considered were (1) mechanical properties of materials, (2) water sorption surface effects in surface diffusion and capillary condensation, (3) water sorption bulk effects for amorphous materials such as viscous flow/spreading, and (4) water-induced stress on interparticle bonding arising from volume expansion. These physical principles enable a comprehensive interpretation of the complex changes observed in tablet properties, which should be valuable in the design of tablet formulations that will be stable to accelerated storage conditions.

  5. Correlation of dissolution and disintegration results for an immediate-release tablet.

    PubMed

    Nickerson, Beverly; Kong, Angela; Gerst, Paul; Kao, Shangming

    2018-02-20

    The drug release rate of a rapidly dissolving immediate-release tablet formulation with a highly soluble drug is proposed to be controlled by the disintegration rate of the tablet. Disintegration and dissolution test methods used to evaluate the tablets were shown to discriminate manufacturing process differences and compositionally variant tablets. In addition, a correlation was established between disintegration and dissolution. In accordance with ICH Q6A, this work demonstrates that disintegration in lieu of dissolution is suitable as the drug product quality control method for evaluating this drug product. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Tableting properties of silica aerogel and other silicates.

    PubMed

    Hentzschel, C M; Alnaief, M; Smirnova, I; Sakmann, A; Leopold, C S

    2012-04-01

    In solid oral dosage forms silicates are commonly used as glidants in low concentration. However, due to their large specific surface area, silicates may also be used as carrier materials for drugs. Moreover, silicates allow amorphisation of drugs by co-grinding or processing with supercritical fluids. The aim of this study was to investigate the physical and the tableting properties of Silica Aerogel (special type of silica with an extremely large specific surface area), Neusilin(®) US2 (magnesium aluminometasilicate), Florite(®) (calcium silicate) and Aerosil(®) 200 (colloidal silica). Powder blends of Avicel(®) PH102 (microcrystalline cellulose) and different amounts of the respective silicate were compacted and analyzed for their tabletability (tensile strength vs. compaction pressure) as well as their Heckel plot. With Neusilin(®) the tabletability appeared to be independent of the silicate concentration, whereas with Florite(®) an increasing silicate concentration led to a higher tensile strength. In contrast, the addition of Silica Aerogel and Aerosil(®) resulted in a decrease of the tensile strength. With Aerosil(®) a maximum tolerable concentration of 20% [w/w] was determined. Plastic deformation of all powder blends decreased with increasing silicate concentration. This effect was most pronounced with Aerosil(®) and least with Florite(®). Tablets with acceptable tensile strength were obtained with all plain silicates except for Aerosil(®). Therefore, these silicates may be used in tablet formulations, e.g. as carrier materials for liquid or amorphous drugs.

  7. Non-contact weight measurement of flat-faced pharmaceutical tablets using terahertz transmission pulse delay measurements.

    PubMed

    Bawuah, Prince; Silfsten, Pertti; Ervasti, Tuomas; Ketolainen, Jarkko; Zeitler, J Axel; Peiponen, Kai-Erik

    2014-12-10

    By measuring the time delay of a terahertz pulse traversing a tablet, and hence its effective refractive index, it is possible to non-invasively and non-destructively detect the weight of tablets made of microcrystalline cellulose (MCC). Two sets of MCC tablets were used in the study: Set A (training set) consisted of 13 tablets with nominally constant height but varying porosities, whereas Set B (test set) comprised of 21 tablets with nominally constant porosity but different heights. A linear correlation between the estimated absolute weight based on the terahertz measurement and the measured weight of both sets of MCC tablets was found. In addition, it was possible to estimate the height of the tablets by utilizing the estimated absolute weight and calculating the relative change of height of each tablet with respect to an ideal tablet. A good agreement between the experimental and the calculated results was found highlighting the potential of this technique for in-line sensing of the weight, porosity and the relative change in height of the tablets compared to a reference/ideal tablet. In this context, we propose a quantitative quality control method to assess the deviations in porosity of tablets immediately after compaction. Copyright © 2014 Elsevier B.V. All rights reserved.

  8. Pharmacokinetics of colon-specific pH and time-dependent flurbiprofen tablets.

    PubMed

    Vemula, Sateesh Kumar; Veerareddy, Prabhakar Reddy; Devadasu, Venkat Ratnam

    2015-09-01

    Present research deals with the development of compression-coated flurbiprofen colon-targeted tablets to retard the drug release in the upper gastro intestinal system, but progressively release the drug in the colon. Flurbiprofen core tablets were prepared by direct compression method and were compression coated using sodium alginate and Eudragit S100. The formulation is optimized based on the in vitro drug release study and further evaluated by X-ray imaging and pharmacokinetic studies in healthy humans for colonic delivery. The optimized formulation showed negligible drug release (4.33 ± 0.06 %) in the initial lag period followed by progressive release (100.78 ± 0.64 %) for 24 h. The X-ray imaging in human volunteers showed that the tablets reached the colon without disintegrating in the upper gastrointestinal tract. The C max of colon-targeted tablets was 12,374.67 ng/ml at T max 10 h, where as in case of immediate release tablets the C max was 15,677.52 ng/ml at T max 3 h, that signifies the ability of compression-coated tablets to target the colon. Development of compression-coated tablets using combination of time-dependent and pH-sensitive approaches was suitable to target the flurbiprofen to colon.

  9. Actual Versus Expected Doses of Half Tablets Containing Prescribed Psychoactive Substances: A Systematic Review.

    PubMed

    Eserian, Jaqueline K; Lombardo, Márcia; Chagas, Jair R; Galduróz, José C F

    2018-02-08

    To assess through a systematic review of the literature if the practice of splitting tablets containing psychoactive/psychotropic medications for medical or economic reasons would result in the expected doses. A MEDLINE and PsycInfo comprehensive search of English-language publications from January 1999 to December 2015 was conducted using the terms describing tablet splitting (tablet splitting, split tablets, tablet subdivision, divided tablets, and half tablets) and psychoactive substances (psychoactive medicines, psychotropic medicines, antidepressants, anxiolytics, anticonvulsants, antipsychotics, and antiparkinsonian agents). An additional supplementary search included the references from the articles found. Studies were included if splitting content was directly related to psychoactive medications and examined the effect of tablet splitting on drug uniformity, weight uniformity, and adherence of psychoactive drugs. Articles were systematically reviewed and examined regarding the study design, methodology, and results of the study. A total of 125 articles were screened, and 13 were selected. Tablet splitting implications are extensive, yet substantial deviations from the ideal weight, potency, and dose uniformity are more prone to be important to patient safety. The uneven division of tablets might result in the administration of different doses than what was prescribed, causing under- or overdosing, which might be relevant depending on the drug. In 55% of the cases, splitting psychoactive drugs was satisfactory. It cannot be generalized that splitting psychoactive drugs compromises dose accuracy, thus tablet splitting might still be employed in cases in which the advantages outweigh the disadvantages. It is recommended that alternatives be adopted to prevent the disadvantages related to tablet splitting. © Copyright 2018 Physicians Postgraduate Press, Inc.

  10. Lallemantia reylenne seeds as superdisintegrant: Formulation and evaluation of nimesulide orodispersible tablets

    PubMed Central

    Malik, Karan; Arora, Gurpreet; Singh, Inderbir; Arora, Sandeep

    2011-01-01

    Aim: Orodispersible tablets also known as fast dissolving tablets disintegrate instantaneously within the mouth and thus can be consumed without water. The present study was aimed to formulate orodispersible tablets of nimesulide by using Lallemantia reylenne seeds as natural superdisintegrant. Materials and Methods: Powdered lallemantia seeds were characterized for powder flow properties (bulk density, tapped density, carr's consolidation index, hausner ratio, angle of repose), swelling index, viscosity, pH, and loss on drying. The prepared tablets were evaluated for different tablet parametric tests, wetting time, water absorption ratio, effective pore radius, porosity, packing fraction, in vitro and in vivo disintegration time, in vitro dissolution and stability studies. Results and Discussion: Increase in Lallementia reylenne concentration had an appreciable effect on tablet hardness and friability which clearly indicated binding potential of the seeds. Water absorption ratio increased with increase in Lallemantia reylenne concentration from batch A1 to A4. Water uptake coupled natural polymer swelling could be the most probable mechanism for concentration dependent reduction in disintegration time by the Lallemantia reylenne seeds. Porosity of the formulated tablets was found to increase from batch A1-A4. The in vitro disintegration results were in line with in vivo disintegration results. Conclusion: It could be concluded that Lallemantia reylenne seeds could be used as natural superdisintegrant in the formulation of orodispersible tablets. PMID:23071942

  11. Integrating a Single Tablet PC in Chemistry, Engineering, and Physics Courses

    ERIC Educational Resources Information Center

    Rogers, James W.; Cox, James R.

    2008-01-01

    A tablet PC is a versatile computer that combines the computing power of a notebook with the pen functionality of a PDA (Cox and Rogers 2005b). The authors adopted tablet PC technology in order to improve the process and product of the lecture format in their chemistry, engineering, and physics courses. In this high-tech model, a single tablet PC…

  12. In-line monitoring of compaction properties on a rotary tablet press during tablet manufacturing of hot-melt extruded amorphous solid dispersions.

    PubMed

    Grymonpré, W; Verstraete, G; Van Bockstal, P J; Van Renterghem, J; Rombouts, P; De Beer, T; Remon, J P; Vervaet, C

    2017-01-30

    As the number of applications for polymers in pharmaceutical development is increasing, there is need for fundamental understanding on how such compounds behave during tableting. This research is focussed on the tableting behaviour of amorphous polymers, their solid dispersions and the impact of hot-melt extrusion on the compaction properties of these materials. Soluplus, Kollidon VA 64 and Eudragit EPO were selected as amorphous polymers since these are widely studied carriers for solid dispersions, while Celecoxib was chosen as BCS class II model drug. Neat polymers and physical mixtures (up to 35% drug load) were processed by hot-melt extrusion (HME), milled and sieved to obtain powders with comparable particle sizes as the neat polymer. A novel approach was used for in-line analysis of the compaction properties on a rotary tablet press (Modul P, GEA) using complementary sensors and software (CDAAS, GEA). By combining 'in-die' and 'out-of-die' techniques, it was possible to investigate in a comprehensive way the impact of HME on the tableting behaviour of amorphous polymers and their formulations. The formation of stable glassy solutions altered the formulations towards more fragmentary behaviour under compression which was beneficial for the tabletability. Principal component analysis (PCA) was applied to summarize the behaviour during compaction of the formulations, enabling the selection of Soluplus and Kollidon VA 64 as the most favourable polymers for compaction of glassy solutions. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Stability of levamisole oral solutions prepared from tablets and powder.

    PubMed

    Chiadmi, Fouad; Lyer, Abdel; Cisternino, Salvatore; Toledano, Audrey; Schlatter, Joël; Ratiney, Robert; Fontan, Jean-Eudes

    2005-08-12

    To study the stability of levamisole oral solutions (25 mg/mL) prepared from powder and tablets stored at 4 +/- 3 degrees C and 23 +/- 2 degrees C in amber glass prescription bottles. Levamisole 25 mg/mL solutions were prepared from commercially available 50-mg tablets or from pure powder in sterile water. Levamisole concentrations were determined in duplicate by a stability-indicating HPLC method at 0, 1, 2, 3, 4, 7, 14, 30, 60 and 90 days. The initial and final pHs of solutions were measured. The recovery of levamisole from tablets was 100 +/- 2.1%. No color or odour changes were observed during the study period. The oral solutions prepared from powder were stable at least 90 days stored at 4 and 23 degrees C. The oral solutions prepared from tablets were stable at least 90 days at 4 degrees C and 15 days when stored at 23 degrees C. The initial pH of solutions prepared from powder and tablets were 5.30 and 4.55, respectively. Initial and final pH values were significantly different (p<0.001) for the two solutions. Levamisole 25 mg/mL oral solutions can be prepared from tablets or powder with sterile water for irrigation and stored for 90 days under refrigeration, taking account of the lack of microbiological contamination.

  14. Desktop 3D printing of controlled release pharmaceutical bilayer tablets.

    PubMed

    Khaled, Shaban A; Burley, Jonathan C; Alexander, Morgan R; Roberts, Clive J

    2014-01-30

    Three dimensional (3D) printing was used as a novel medicine formulation technique for production of viable tablets capable of satisfying regulatory tests and matching the release of standard commercial tablets. Hydroxypropyl methylcellulose (HPMC 2208) (Methocel™ K100M Premium) and poly(acrylic acid) (PAA) (Carbopol(®) 974P NF) were used as a hydrophilic matrix for a sustained release (SR) layer. Hypromellose(®) (HPMC 2910) was used as a binder while microcrystalline cellulose (MCC) (Pharmacel(®) 102) and sodium starch glycolate (SSG) (Primojel(®)) were used as disintegrants for an immediate release (IR) layer. Commercial guaifenesin bi-layer tablets (GBT) were used as a model drug (Mucinex(®)) for this study. There was a favourable comparison of release of the active guaifenesin from the printed hydrophilic matrix compared with the commercially available GBT. The printed formulations were also evaluated for physical and mechanical properties such as weight variation, friability, hardness and thickness as a comparison to the commercial tablet and were within acceptable range as defined by the international standards stated in the United States Pharmacopoeia (USP). All formulations (standard tablets and 3D printed tablets) showed Korsmeyer-Peppas n values between 0.27 and 0.44 which indicates Fickian diffusion drug release through a hydrated HPMC gel layer. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Risperidone oral disintegrating mini-tablets: A robust-product for pediatrics.

    PubMed

    El-Say, Khalid M; Ahmed, Tarek A; Abdelbary, Maged F; Ali, Bahaa E; Aljaeid, Bader M; Zidan, Ahmed S

    2015-12-01

    This study was aimed at developing risperidone oral disintegrating mini-tablets (OD-mini-tablets) as age-appropriate formulations and to assess their suitability for infants and pediatric use. An experimental Box-Behnken design was applied to assure high quality of the OD-mini-tablets and reduce product variability. The design was employed to understand the influence of the critical excipient combinations on the production of OD-mini-tablets and thus guarantee the feasibility of obtaining products with dosage form uniformity. The variables selected were mannitol percent in Avicel (X1), swelling pressure of the superdisintegrant (X2), and the surface area of Aerosil as a glidant (X3). Risperidone-excipient compatibilities were investigated using FTIR and the spectra did not display any interaction. Fifteen formulations were prepared and evaluated for pre- and post-compression characteristics. The prepared OD-mini-tablet batches were also assessed for disintegration in simulated salivary fluid (SSF, pH 6.2) and in reconstituted skimmed milk. The optimized formula fulfilled the requirements for crushing strength of 5 kN with minimal friability, disintegration times of 8.4 and 53.7 s in SSF and skimmed milk, respectively. This study therefore proposes the risperidone OD-mini-tablet formula having robust mechanical properties, uniform and precise dosing of medication with short disintegration time suitable for pediatric use.

  16. Channelled tablets: An innovative approach to accelerating drug release from 3D printed tablets.

    PubMed

    Sadia, Muzna; Arafat, Basel; Ahmed, Waqar; Forbes, Robert T; Alhnan, Mohamed A

    2018-01-10

    Conventional immediate release dosage forms involve compressing the powder with a disintegrating agent that enables rapid disintegration and dissolution upon oral ingestion. Among 3D printing technologies, the fused deposition modelling (FDM) 3D printing technique has a considerable potential for patient-specific dosage forms. However, the use of FDM 3D printing in tablet manufacturing requires a large portion of polymer, which slows down drug release through erosion and diffusion mechanisms. In this study, we demonstrate for the first time the use of a novel design approach of caplets with perforated channels to accelerate drug release from 3D printed tablets. This strategy has been implemented using a caplet design with perforating channels of increasing width (0.2, 0.4, 0.6, 0.8 or 1.0mm) and variable length, and alignment (parallel or at right angle to tablet long axis). Hydrochlorothiazide (BCS class IV drug) was chosen as the model drug as enhanced dissolution rate is vital to guarantee oral bioavailability. The inclusion of channels exhibited an increase in the surface area/volume ratio, however, the release pattern was also influenced by the width and the length of the channel. A channel width was ≥0.6mm deemed critical to meet the USP criteria of immediate release products. Shorter multiple channels (8.6mm) were more efficient at accelerating drug release than longer channels (18.2mm) despite having comparable surface area/mass ratio. This behaviour may be linked to the reduced flow resistance within the channels and the faster fragmentation during dissolution of these tablets. In conclusion, the width and length of the channel should be carefully considered in addition to surface area/mass when optimizing drug release from 3D printed designs. The incorporation of short channels can be adopted in the designs of dosage forms, implants or stents to enhance the release rate of eluting drug from polymer-rich structures. Copyright © 2017 Elsevier B.V. All

  17. 21 CFR 520.2345h - Tetracycline hydrochloride, sodium novobiocin, and prednisolone tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... prednisolone tablets. 520.2345h Section 520.2345h Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... ANIMAL DRUGS § 520.2345h Tetracycline hydrochloride, sodium novobiocin, and prednisolone tablets. (a) Specifications. Each tablet contains the equivalent of 60 milligrams of tetracycline hydrochloride, 60 milligrams...

  18. Smartphones, tablets and mobile applications for radiology.

    PubMed

    Székely, András; Talanow, Roland; Bágyi, Péter

    2013-05-01

    Smartphones are phone devices that may also be used for browsing, navigation and running smaller computer programs called applications. One may consider them as compact personal computers which are primarily to be used for making phone calls. Tablets or "tablet PCs" are fully functioning standalone computers the size of a thin LCD monitor that use the screen itself for control and data input. Both of these devices may be categorized based on the mobile operating system that they use. The aim of this study is to illustrate how smartphones and tablets can be used by diagnostic imaging professionals, radiographers and residents, and to introduce relevant applications that are available for their field. A search was performed on iTunes, Android Market, Blackberry App World, and Windows Phone Marketplace for mobile applications pertinent to the field of diagnostic imaging. The following terms were applied for the search strategy: (1) radiology, (2) X-ray, (3) ultrasound, (4) MRI, (5) CT, (6) radiographer, (7) nuclear medicine. Two radiologists and one radiology resident reviewed the results. Our review was limited to english-language software. Additional applications were identified by reviewing the list of similar software provided in the description of each application. We downloaded and installed all applications that appeared relevant to an appropriate mobile phone or tablet device. We identified and reviewed a total of 102 applications. We ruled out 1 non-English application and 20 other applications that were created for entertainment purposes. Thus our final list includes 81 applications in the following five categories: diagnostic reading, decision support applications, medical books, interactive encyclopedias, and journal reading programs. Smartphones and tablets offer new opportunities for diagnostic imaging practitioners; these easy-to-use devices equipped with excellent display may be used for diagnostic reading, reference, learning, consultation, and for

  19. Commentary: Tablet PCs--Lightweights with a Teaching Punch

    ERIC Educational Resources Information Center

    Parslow, Graham R.

    2010-01-01

    Tablet (or slate) computers are a group of small portable computers that have two features in common, a touch screen and wireless connectivity to the web. At the 2010 Consumer Electronics show held in January in Las Vegas, this category of product caused the greatest interest ahead of the release of the Apple iPad (www.cesweb.org). The tablet PC…

  20. Effect of crospovidone and hydroxypropyl cellulose on carbamazepine in high-dose tablet formulation.

    PubMed

    Flicker, Felicia; Betz, Gabriele

    2012-06-01

    The aim of this study was to develop a high-dose tablet formulation of the poorly soluble carbamazepine (CBZ) with sufficient tablet hardness and immediate drug release. A further aim was to investigate the influence of various commercial CBZ raw materials on the optimized tablet formulation. Hydroxypropyl cellulose (HPC-SL) was selected as a dry binder and crospovidone (CrosPVP) as a superdisintegrant. A direct compacted tablet formulation of 70% CBZ was optimized by a 3² full factorial design with two input variables, HPC (0--10%) and CrosPVP (0--5%). Response variables included disintegration time, amount of drug released at 15 and 60 min, and tablet hardness, all analyzed according to USP 31. Increasing HPC-SL together with CrosPVP not only increased tablet hardness but also reduced disintegration time. Optimal condition was achieved in the range of 5--9% HPC and 3--5% CrosPVP, where tablet properties were at least 70 N tablet hardness, less than 1 min disintegration, and within the USP requirements for drug release. Testing the optimized formulation with four different commercial CBZ samples, their variability was still observed. Nonetheless, all formulations conformed to the USP specifications. With the excipients CrosPVP and HPC-SL an immediate release tablet formulation was successfully formulated for high-dose CBZ of various commercial sources.

  1. Supporting Tablet Configuration, Tracking, and Infection Control Practices in Digital Health Interventions: Study Protocol.

    PubMed

    Furberg, Robert D; Ortiz, Alexa M; Zulkiewicz, Brittany A; Hudson, Jordan P; Taylor, Olivia M; Lewis, Megan A

    2016-06-27

    Tablet-based health care interventions have the potential to encourage patient care in a timelier manner, allow physicians convenient access to patient records, and provide an improved method for patient education. However, along with the continued adoption of tablet technologies, there is a concomitant need to develop protocols focusing on the configuration, management, and maintenance of these devices within the health care setting to support the conduct of clinical research. Develop three protocols to support tablet configuration, tablet management, and tablet maintenance. The Configurator software, Tile technology, and current infection control recommendations were employed to develop three distinct protocols for tablet-based digital health interventions. Configurator is a mobile device management software specifically for iPhone operating system (iOS) devices. The capabilities and current applications of Configurator were reviewed and used to develop the protocol to support device configuration. Tile is a tracking tag associated with a free mobile app available for iOS and Android devices. The features associated with Tile were evaluated and used to develop the Tile protocol to support tablet management. Furthermore, current recommendations on preventing health care-related infections were reviewed to develop the infection control protocol to support tablet maintenance. This article provides three protocols: the Configurator protocol, the Tile protocol, and the infection control protocol. These protocols can help to ensure consistent implementation of tablet-based interventions, enhance fidelity when employing tablets for research purposes, and serve as a guide for tablet deployments within clinical settings.

  2. Development, evaluation and pharmacokinetics of time-dependent ketorolac tromethamine tablets.

    PubMed

    Vemula, Sateesh Kumar; Veerareddy, Prabhakar Reddy

    2013-01-01

    The present study was intended to develop a time-dependent colon-targeted compression-coated tablets of ketorolac tromethamine (KTM) using hydroxypropyl methylcellulose (HPMC) that release the drug slowly but completely in the colonic region by retarding the drug releases in stomach and small intestine. KTM core tablets were prepared by direct compression method and were compression coated with HPMC. The formulation is optimized based on the in vitro drug release studies and further evaluated by X-ray imaging technique in healthy humans to ensure the colonic delivery. To prove these results, in vivo pharmacokinetic studies in human volunteers were designed to study the in vitro-in vivo correlation. From the in vitro dissolution study, optimized formulation F3 showed negligible drug release (6.75 ± 0.49%) in the initial lag period followed by slow release (97.47 ± 0.93%) for 24 h which clearly indicates that the drug is delivered to the colon. The X-ray imaging studies showed that the tablets reached the colon without disintegrating in upper gastrointestinal system. From the pharmacokinetic evaluation, the immediate-release tablets producing peak plasma concentration (C(max)) was 4482.74 ng/ml at 2 h T(max) and colon-targeted tablets showed C(max) = 3562.67 ng/ml at 10 h T(max). The area under the curve for the immediate-release and compression-coated tablets was 10595.14 and 18796.70 ng h/ml and the mean resident time was 3.82 and 10.75 h, respectively. Thus, the compression-coated tablets based on time-dependent approach were preferred for colon-targeted delivery of ketorolac.

  3. Evaluating tablet computers as a survey tool in rural communities.

    PubMed

    Newell, Steve M; Logan, Henrietta L; Guo, Yi; Marks, John G; Shepperd, James A

    2015-01-01

    Although tablet computers offer advantages in data collection over traditional paper-and-pencil methods, little research has examined whether the 2 formats yield similar responses, especially with underserved populations. We compared the 2 survey formats and tested whether participants' responses to common health questionnaires or perceptions of usability differed by survey format. We also tested whether we could replicate established paper-and-pencil findings via tablet computer. We recruited a sample of low-income community members living in the rural southern United States. Participants were 170 residents (black = 49%; white = 36%; other races and missing data = 15%) drawn from 2 counties meeting Florida's state statutory definition of rural with 100 persons or fewer per square mile. We randomly assigned participants to complete scales (Center for Epidemiologic Studies Depression Inventory and Regulatory Focus Questionnaire) along with survey format usability ratings via paper-and-pencil or tablet computer. All participants rated a series of previously validated posters using a tablet computer. Finally, participants completed comparisons of the survey formats and reported survey format preferences. Participants preferred using the tablet computer and showed no significant differences between formats in mean responses, scale reliabilities, or in participants' usability ratings. Overall, participants reported similar scales responses and usability ratings between formats. However, participants reported both preferring and enjoying responding via tablet computer more. Collectively, these findings are among the first data to show that tablet computers represent a suitable substitute among an underrepresented rural sample for paper-and-pencil methodology in survey research. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

  4. Abilities and Affordances: Factors Influencing Successful Child-Tablet Communication

    ERIC Educational Resources Information Center

    Dubé, Adam K.; McEwen, Rhonda N.

    2017-01-01

    Using Luhmann's communication theory and affordance theories, we develop a framework to examine how kindergarten-grade 2 students interact with tablet computers. We assessed whether cognitive ability and device configuration influence how successfully children use tablet computers. We found that children's limited ability to direct their cognitive…

  5. Tablet splitting of a narrow therapeutic index drug: a case with levothyroxine sodium.

    PubMed

    Shah, Rakhi B; Collier, Jarrod S; Sayeed, Vilayat A; Bryant, Arthur; Habib, Muhammad J; Khan, Mansoor A

    2010-09-01

    Levothyroxine is a narrow therapeutic index, and to avoid adverse effect associated with under or excessive dosage, the dose response is carefully titrated. The tablets are marketed with a score providing an option to split. However, there are no systematic studies evaluating the effect of splitting on dose accuracy, and current study was undertaken to evaluate effects of splitting and potential causes for uniformity failures by measuring assay and content uniformity in whole and split tablets. Stability was evaluated by assaying drug for a period of 8 weeks. Effect of formulation factors on splittability was evaluated by a systematic investigation of formulation factors by preparing levothyroxine tablets in house by varying the type of excipients (binder, diluent, disintegrant, glidant) or by varying the processing factors (granulating liquid, mixing type, compression pressure). The tablets were analyzed using novel analytical tool such as near infrared chemical imaging to visualize the distribution of levothyroxine. Assay was not significantly different for whole versus split tablets irrespective of method of splitting (hand or splitter), and splitting also had no measurable impact on the stability. Split tablets either by hand or splitter showed higher rate of content uniformity failures as compared to whole tablets. Tablet splitter produced more fragmentation and, hence, more content uniformity and friability failures. Chemical imaging data revealed that the distribution of levothyroxine was heterogeneous and was dependent on type of binder and the process used in the manufacture of tablets. Splitting such tablets could prove detrimental if sub- or super-potency becomes an issue.

  6. The practice and clinical implications of tablet splitting in international health

    PubMed Central

    Elliott, Ivo; Mayxay, Mayfong; Yeuichaixong, Sengchanh; Lee, Sue J; Newton, Paul N

    2014-01-01

    Objective Tablet splitting is frequently performed to facilitate correct dosing, but the practice and implications in low-income settings have rarely been discussed. Methods We selected eight drugs, with narrow therapeutic indices or critical dosages, frequently divided in the Lao PDR (Laos). These were split, by common techniques used in Laos, by four nurses and four laypersons. The mean percentage deviation from the theoretical expected weight and weight loss of divided tablets/capsules were recorded. Results Five of eight study drugs failed, on splitting, to meet European Pharmacopoeia recommendations for tablet weight deviation from the expected weight of tablet/capsule halves with 10% deviating by more than 25%. There was a significant difference in splitting accuracy between nurses and laypersons (P = 0.027). Coated and unscored tablets were less accurately split than uncoated (P = 0.03 and 0.0019 for each half) and scored (0.0001 for both halves) tablets. Conclusion These findings have potential clinical implications on treatment outcome and the development of antimicrobial resistance. Investment by drug companies in a wider range of dosage units, particularly for narrow therapeutic index and critical dosage medicines, is strongly recommended. PMID:24702766

  7. [Clinical observation of teacher tablets in treatment of pharyngitis].

    PubMed

    Qin, Dong-yun; Wu, Tie

    2008-07-01

    To evaluate the efficacy of teacher tablets in the treatment of pharyngitis. One hundred and thirty six patients with acute pharyngitis or chronic pharyngitis in attack were randamly divided into two groups: treated group (n=68), the patients were given teacher tablets for 7 days, control group (n=68), the patients were given Qinlian capsule for 7 days. Before and after the experimental medicine-taking test, general condition, clinical symptoms and features of examinations on laryngo-pharynx, throat swab bacterial culture were measured. After 7 day medicine-taking experiment, teacher tablets can improve clinical symptoms (at an efficacy rate of more than 60%) and features (at an efficacy rate of more than 80%) of laryngopharynx, in treated group, the inhibition ratios of alpha streptococcus, neisseria and staphylococcus aureus are more than 50%. There are no significant difference between treated group and control groups in those detected index. Teacher tablets is effective for pharyagitis.

  8. Life-Span Differences in the Uses and Gratifications of Tablets: Implications for Older Adults

    PubMed Central

    Magsamen-Conrad, Kate; Dowd, John; Abuljadail, Mohammad; Alsulaiman, Saud; Shareefi, Adnan

    2015-01-01

    This study extends Uses and Gratifications theory by examining the uses and gratifications of a new technological device, the tablet computer, and investigating the differential uses and gratifications of tablet computers across the life-span. First, we utilized a six-week tablet training intervention to adapt and extend existing measures to the tablet as a technological device. Next, we used paper-based and online surveys (N=847), we confirmed four main uses of tablets: 1) Information Seeking, 2) Relationship Maintenance, 3) Style, 4) Amusement and Killing time, and added one additional use category 5) Organization. We discovered differences among the five main uses of tablets across the life-span, with older adults using tablets the least overall. Builders, Boomers, GenX and GenY all reported the highest means for information seeking. Finally, we used a structural equation model to examine how uses and gratifications predicts hours of tablet use. The study provides limitations and suggestions for future research and marketers. In particular, this study offers insight to the relevancy of theory as it applies to particular information and communication technologies and consideration of how different periods in the life-span affect tablet motivations. PMID:26113769

  9. Life-Span Differences in the Uses and Gratifications of Tablets: Implications for Older Adults.

    PubMed

    Magsamen-Conrad, Kate; Dowd, John; Abuljadail, Mohammad; Alsulaiman, Saud; Shareefi, Adnan

    2015-11-01

    This study extends Uses and Gratifications theory by examining the uses and gratifications of a new technological device, the tablet computer, and investigating the differential uses and gratifications of tablet computers across the life-span. First, we utilized a six-week tablet training intervention to adapt and extend existing measures to the tablet as a technological device. Next, we used paper-based and online surveys ( N =847), we confirmed four main uses of tablets: 1) Information Seeking, 2) Relationship Maintenance, 3) Style, 4) Amusement and Killing time, and added one additional use category 5) Organization. We discovered differences among the five main uses of tablets across the life-span, with older adults using tablets the least overall. Builders, Boomers, GenX and GenY all reported the highest means for information seeking. Finally, we used a structural equation model to examine how uses and gratifications predicts hours of tablet use. The study provides limitations and suggestions for future research and marketers. In particular, this study offers insight to the relevancy of theory as it applies to particular information and communication technologies and consideration of how different periods in the life-span affect tablet motivations.

  10. The Tablet Device in Hospital Neurology and in Neurology Graduate Medical Education

    PubMed Central

    Newey, Christopher R.; Bhimraj, Adarsh

    2015-01-01

    Background and Purpose: There is limited literature on tablet devices for neurohospitalists and in neurological graduate medical education. This study evaluated utilization, benefits, and limitations of customized tablets on inpatient neurology practice and resident education. The hypothesis was the perception of the tablet would be positive, given their portability, convenience to accessing point-of-care reference, and accessibility to the electronic medical record. Methods: Second-generation iPads with neurology-specific applications and literature were provided to our in-hospital general, stroke, and consult neurology teams. After 1 year, residents on these teams were surveyed on demographic data, familiarity, and utilization of the iPad and their perceptions of the device. Results: All 27 residents responded to the survey. Most participants (23 of 27) used a tablet while on inpatient service. Twelve regularly utilized the neurology-specific apps and/or accessed scientific articles. Technologically savvy residents felt significantly more comfortable using tablets and were more quickly acquainted with the features. Thirteen respondents wanted a formal orientation on the advanced features of the tablet independent of their familiarity with the device or level of technological comfort. Conclusion: Overall, the perception was that the tablet was beneficial for inpatient clinical care and as an educational reference. Participants became easily familiarized with the device features quickly, regardless of whether they owned one previously or not. Most physicians indicated interest in advanced features of tablets; however, a formal orientation may be beneficial for optimal utilization. A reliable network connection is essential to in-hospital use of tablet devices. Additional research pertaining to patient outcomes, objective educational benefit, and cost-effectiveness is necessary. PMID:25553224

  11. Investigating the effect of processing parameters on pharmaceutical tablet disintegration using a real-time particle imaging approach.

    PubMed

    Rajkumar, Arthi D; Reynolds, Gavin K; Wilson, David; Wren, Stephen; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    Tablet disintegration is a fundamental parameter that is tested in vitro before a product is released to the market, to give confidence that the tablet will break up in vivo and that active drug will be available for absorption. Variations in tablet properties cause variation in disintegration behaviour. While the standardised pharmacopeial disintegration test can show differences in the speed of disintegration of different tablets, it does not give any mechanistic information about the underlying cause of the difference. With quantifiable disintegration data, and consequently an improved understanding into tablet disintegration, a more knowledge-based approach could be applied to the research and development of future tablet formulations. The aim of the present research was to introduce an alternative method which will enable a better understanding of tablet disintegration using a particle imaging approach. A purpose-built flow cell was employed capable of online observation of tablet disintegration, which can provide information about the changing tablet dimensions and the particles released with time. This additional information can improve the understanding of how different materials and process parameters affect tablet disintegration. Standard USP analysis was also carried out to evaluate and determine whether the flow cell method can suitably differentiate the disintegration behaviour of tablets produced using different processing parameters. Placebo tablets were produced with varying ratios of insoluble and soluble filler (mannitol and MCC, respectively) so that the effect of variation in the formulation can be investigated. To determine the effect of the stress applied during granulation and tableting on tablet disintegration behaviour, analysis was carried out on tablets produced using granular material compressed at 20 or 50bar, where a tableting load of either 15 or 25kN was used. By doing this the tablet disintegration was examined in terms of the

  12. Tablet PC interaction with digital micromirror device (DMD)

    NASA Astrophysics Data System (ADS)

    Refai, Hakki H.; Dahshan, Mostafa H.; Sluss, James J., Jr.

    2007-02-01

    Digital light processing (DLP) is an innovative display technology that uses an optical switch array, known as a digital micromirror device (DMD), which allows digital control of light. To date, DMDs have been used primarily as high-speed spatial light modulators for projector applications. A tablet PC is a notebook or slate-shaped mobile PC. Its touch screen or digitizing tablet technology allows the user to operate the notebook with a stylus or digital pen instead of using a keyboard or mouse. In this paper, we describe an interface solution that translates any sketch on the tablet PC screen to an identical mirror-copy over the cross-section of the DMD micromirrors such that the image of the sketch can be projected onto a special screen. An algorithm has been created to control each single micromirror of the hundreds of thousands of micromirrors that cover the DMD surface. We demonstrate the successful application of a DMD to a high-speed two-dimensional (2D) scanning environment, acquiring the data from the tablet screen and launching its contents to the projection screen; with very high accuracy up to 13.68 μm x 13.68 μm of mirror pitch.

  13. Development and evaluation of novel antihypertensive orodispersible tablets.

    PubMed

    Khan, Hafeez Ullah; Hanif, Muhammad; Sarfraz, Rai M; Maheen, Safirah; Afzal, Samina; Sher, Muhammad; Afzal, Khurram; Mahmood, Asif; Shamim, Ayesha

    2017-09-01

    Objective of present study was to enhance patient compliance in pediatrics and geriatrics patients of Hypertension. To achieve this target, innovative orodispersible tablets of atenolol and atorvastatin was developed to produce instant action by rapidly disintegrating into oral cavity. Three different techniques like direct compression, effervescent and sublimation methods were used to prepare these tablets (Five batches of tablets by each method) by using two superdisintegrants like Sodium starch glycolate and pregelatinized starch alone and in combination. Pre-formulation studies including rheological analysis (Bulk density, tapped density, Angle of repose, Carr's compressibility index, Hausner's ratio), compatibility studies such as Fourier transform infrared spectrophotometry (FTIR) and Differential scanning colorimetry (DSC), Post-compression and stability studies were also performed. Finally, results were statistically evaluated by the applying one way ANOVA test and mean. It was concluded that the formulation F8 containing Sodium starch glycolate 2% and pregelatinized starch 6% found best regarding disintegration time, wetting volume, wetting time, release studies etc. The order in which drug release was quicker is Pregelatinized starch plus Sodium starch glycolate > Pregelatinized starch > Sodium starch glycolate (primojel). It was concluded that sublimation method was the best among three methods used for orodispersible tablets formulations.

  14. Preparation of orally disintegrating tablets with taste-masking function: masking effect in granules prepared with correctives using the dry granulation method and evaluation of tablets prepared using the taste-masked granules.

    PubMed

    Kawano, Yayoi; Ito, Akihiko; Sasatsu, Masanaho; Machida, Yoshiharu

    2010-01-01

    We investigated several methods of taste masking in the preparation of orally disintegrating tablets (ODTs), using furosemide (FU) as a model drug. Four types of FU preparations were prepared: granules with maltitol (MA), granules with yogurt powder (YO), a physical mixture of FU and MA, and a physical mixture of FU and YO. All taste-masking granules were prepared using the dry granulation method. The taste of each type of preparation was evaluated. All four preparations markedly improved the taste of the FU tablets, but the mixing ratios of the correctives did not affect the masking effect. No difference in masking effect was found between MA and YO in the physical mixtures, but the masking effect in the granules with YO was superior to that of the granules with MA. Taste-masked FU tablets were prepared using the direct compression method; crystalline cellulose (Avicel PH-302) and mannitol were added as excipients at the mixing ratio of 1/1. All four types of tablets displayed sufficient hardness, but MA-containing tablets were harder than YO-containing tablets. The hardness of the tablets prepared from YO granules increased as the YO content increased. The most rapidly disintegrating tablets were those of YO granules prepared at a mixing ratio of FU/YO=1/1, which disintegrated within 20 s, followed by the tablets of MA granules prepared at a mixing ratio of FU/MA=1/1. The disintegration times of the tablets made from physical mixtures, in contrast, were longer than 200 s. Disintegration time lengthened as the mixing ratio of YO or MA increased. The hardness and disintegration time of these tablets could be controlled by varying the compression pressure. We found that YO is more useful than MA in masking unpleasant tastes and confirmed that orally disintegrating tablets with taste-masking function can be prepared using granules of YO prepared using the dry granulation method as a new corrective.

  15. Tablet Computer Literacy Levels of the Physical Education and Sports Department Students

    ERIC Educational Resources Information Center

    Hergüner, Gülten

    2016-01-01

    Education systems are being affected in parallel by newly emerging hardware and new developments occurring in technology daily. Tablet usage especially is becoming ubiquitous in the teaching-learning processes in recent years. Therefore, using the tablets effectively, managing them and having a high level of tablet literacy play an important role…

  16. 78 FR 1247 - Certain Electronic Devices, Including Wireless Communication Devices, Tablet Computers, Media...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-08

    ... Wireless Communication Devices, Tablet Computers, Media Players, and Televisions, and Components Thereof... devices, including wireless communication devices, tablet computers, media players, and televisions, and... wireless communication devices, tablet computers, media players, and televisions, and components thereof...

  17. Risperidone mucoadhesive buccal tablets: formulation design, optimization and evaluation

    PubMed Central

    Çelik, Burak

    2017-01-01

    The aim of this study was to design and optimize risperidone (RIS) mucoadhesive buccal tablets for systemic delivery as an alternative route. Direct compression method was used for the preparation of buccal tablets, and screening studies were conducted with different polymers to determine their effects on tablet characteristics. Carbopol® (CP) and sodium alginate (SA) were selected as two polymer types for further optimization studies by applying response surface methodology. Tablet hardness (TH), ex vivo residence time (RT), and peak detachment force (DF) from buccal mucosa were selected as three important responses. Physicochemical compatibility of formulation excipients and RIS was evaluated by using Fourier transform infrared (FT-IR) spectroscopy and differential scanning calorimetry (DSC) analysis. In vitro drug release profiles and release kinetics were investigated; swelling index and matrix erosion studies were conducted. Optimum formulation consisted of 16.4% CP and 20.3% SA, which provided 7.67±0.29 hour ex vivo RT, 45.52±4.85 N TH, and 2.12±0.17 N DF. FT-IR spectroscopy and DSC analysis revealed that there was no chemical interaction present between tablet ingredients. Cumulative RIS release of >90% was achieved after 8 hours of in vitro dissolution studies, which was supported by swelling and matrix erosion analysis. Mechanism of RIS release was fitted best to zero-order model, while release exponent (n) value of 0.77 demonstrated an anomalous (non-Fickian) release, indicating combined erosion and swelling mechanism. The results suggested that optimized buccal tablets of RIS would be a promising and alternative delivery system for the treatment of schizophrenia. PMID:29225461

  18. Formulation and evaluation of sublingual tablets containing Sumatriptan succinate

    PubMed Central

    Prajapati, Shailesh T; Patel, Parth B; Patel, Chhagan N

    2012-01-01

    Objective: Sumatriptan succinate is a selective 5-hydroxytryptamine-1 receptor agonist effective in the acute treatment of migraine headaches, having low bioavailability of about 15% orally due to first-pass metabolism. The purpose of this research was to mask the intensely bitter taste of Sumatriptan succinate and to formulate fast-acting, taste-masked sublingual tablet formulation. Materials and Methods: Taste masking was performed by solid dispersion method with mannitol and ion exchange with Kyron T 114 because it releases the drug in salivary pH. The resultant batches were evaluated for in-vivo taste masking as well compatability study (Fourier transform infrared (FTIR) and differential scanning calorimetry (DSC)). For a better feel in the mouth, menthol and sweetener Na saccharine were added to the tablet formulation. The tablets were prepared by direct compression and evaluated for weight variation, thickness, friability, drug content, hardness, disintegration time, wetting time, in vitro drug release, and in vitro permeation study. Results and Discussion: Optimized batches disintegrated in vitro within 28-34 s. Maximum drug release could be achieved with in 10 min for the solid dispersion batches and 14-15 min for the ion-exchange batches with Kyron T 114. The optimized tablet formulation showed better taste and the formulated sublingual tablets may act as a potential alternate for the Sumatriptan succinate oral tablet. Conclusion: Sumatriptan succinate can be successfully taste-masked by both the solid dispersion method using mannitol by the melting method and Ion exchange resin with Kyron T114. It was also concluded that prepared formulation improve bioavailability by prevention of first pass metabolism. PMID:23373008

  19. Prescription Tablets in the Digital Age: A Cross-Sectional Study Exploring Patient and Physician Attitudes Toward the Use of Tablets for Clinic-Based Personalized Health Care Information Exchange

    PubMed Central

    Palakodeti, Sandeep; Kvedar, Joseph C; Jethwani, Kamal

    2015-01-01

    Background To reduce the cost of health care while increasing efficiency and quality, health systems are seeking innovative means to engage and empower patients. Improved use of information technology and electronic health record (EHR) infrastructure is essential, and required for “meaningful use” as mandated by the federal government. Providing personalized health information using tablets at the point of care could enhance the clinical experience and enable efficient collection of patient reported outcome measures to guide clinical decision making. Objective The aim of this study is to explore patient and provider attitudes and interest in a proposed clinic-based tablet system for personal health information exchange. To provide a context to understand patients’ use of tablets during their clinic visit, we also examine patients’ current activities and time spent in the waiting room, and their use of health information resources. Methods Surveys were administered to 84 patients in the waiting room of a community health center affiliated with Massachusetts General Hospital (MGH) in Boston, MA. This survey included a vignette and illustration describing a proposed tablet-based system in which the patient, upon sign in at the clinic, receives a tablet loaded with personalized information tailored to their specific medical conditions and preferences. Patients were queried about their interest in such a system in comparison to traditional forms of patient education as well as their current health information seeking behaviors and activities and time spent in the waiting room. Interviews with five MGH-affiliated health care providers were conducted to assess their opinions regarding the proposed tablet system. Results The majority (>60%) of patients were “very” or “extremely” interested in the proposed tablet system and thought it would improve their knowledge about their medical condition (60%), assist them in making healthy choices (57%), and help them

  20. Prescription Tablets in the Digital Age: A Cross-Sectional Study Exploring Patient and Physician Attitudes Toward the Use of Tablets for Clinic-Based Personalized Health Care Information Exchange.

    PubMed

    Patel, Vishal; Hale, Timothy M; Palakodeti, Sandeep; Kvedar, Joseph C; Jethwani, Kamal

    2015-10-19

    To reduce the cost of health care while increasing efficiency and quality, health systems are seeking innovative means to engage and empower patients. Improved use of information technology and electronic health record (EHR) infrastructure is essential, and required for "meaningful use" as mandated by the federal government. Providing personalized health information using tablets at the point of care could enhance the clinical experience and enable efficient collection of patient reported outcome measures to guide clinical decision making. The aim of this study is to explore patient and provider attitudes and interest in a proposed clinic-based tablet system for personal health information exchange. To provide a context to understand patients' use of tablets during their clinic visit, we also examine patients' current activities and time spent in the waiting room, and their use of health information resources. Surveys were administered to 84 patients in the waiting room of a community health center affiliated with Massachusetts General Hospital (MGH) in Boston, MA. This survey included a vignette and illustration describing a proposed tablet-based system in which the patient, upon sign in at the clinic, receives a tablet loaded with personalized information tailored to their specific medical conditions and preferences. Patients were queried about their interest in such a system in comparison to traditional forms of patient education as well as their current health information seeking behaviors and activities and time spent in the waiting room. Interviews with five MGH-affiliated health care providers were conducted to assess their opinions regarding the proposed tablet system. The majority (>60%) of patients were "very" or "extremely" interested in the proposed tablet system and thought it would improve their knowledge about their medical condition (60%), assist them in making healthy choices (57%), and help them to feel more comfortable talking with their provider

  1. High-throughput prediction of tablet weight and trimethoprim content of compound sulfamethoxazole tablets for controlling the uniformity of dosage units by NIR.

    PubMed

    Dong, Yanhong; Li, Juan; Zhong, Xiaoxiao; Cao, Liya; Luo, Yang; Fan, Qi

    2016-04-15

    This paper establishes a novel method to simultaneously predict the tablet weight (TW) and trimethoprim (TMP) content of compound sulfamethoxazole tablets (SMZCO) by near infrared (NIR) spectroscopy with partial least squares (PLS) regression for controlling the uniformity of dosage units (UODU). The NIR spectra for 257 samples were measured using the optimized parameter values and pretreated using the optimized chemometric techniques. After the outliers were ignored, two PLS models for predicting TW and TMP content were respectively established by using the selected spectral sub-ranges and the reference values. The TW model reaches the correlation coefficient of calibration (R(c)) 0.9543 and the TMP content model has the R(c) 0.9205. The experimental results indicate that this strategy expands the NIR application in controlling UODU, especially in the high-throughput and rapid analysis of TWs and contents of the compound pharmaceutical tablets, and may be an important complement to the common NIR on-line analytical method for pharmaceutical tablets. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Supporting Tablet Configuration, Tracking, and Infection Control Practices in Digital Health Interventions: Study Protocol

    PubMed Central

    Furberg, Robert D; Zulkiewicz, Brittany A; Hudson, Jordan P; Taylor, Olivia M; Lewis, Megan A

    2016-01-01

    Background Tablet-based health care interventions have the potential to encourage patient care in a timelier manner, allow physicians convenient access to patient records, and provide an improved method for patient education. However, along with the continued adoption of tablet technologies, there is a concomitant need to develop protocols focusing on the configuration, management, and maintenance of these devices within the health care setting to support the conduct of clinical research. Objective Develop three protocols to support tablet configuration, tablet management, and tablet maintenance. Methods The Configurator software, Tile technology, and current infection control recommendations were employed to develop three distinct protocols for tablet-based digital health interventions. Configurator is a mobile device management software specifically for iPhone operating system (iOS) devices. The capabilities and current applications of Configurator were reviewed and used to develop the protocol to support device configuration. Tile is a tracking tag associated with a free mobile app available for iOS and Android devices. The features associated with Tile were evaluated and used to develop the Tile protocol to support tablet management. Furthermore, current recommendations on preventing health care–related infections were reviewed to develop the infection control protocol to support tablet maintenance. Results This article provides three protocols: the Configurator protocol, the Tile protocol, and the infection control protocol. Conclusions These protocols can help to ensure consistent implementation of tablet-based interventions, enhance fidelity when employing tablets for research purposes, and serve as a guide for tablet deployments within clinical settings. PMID:27350013

  3. Process analytical technology to understand the disintegration behavior of alendronate sodium tablets.

    PubMed

    Xu, Xiaoming; Gupta, Abhay; Sayeed, Vilayat A; Khan, Mansoor A

    2013-05-01

    Various adverse events including esophagus irritations have been reported with the use of alendronate tablets, likely attributed to the rapid tablet disintegration in the mouth or esophagus. Accordingly, the disintegration of six alendronate tablet drug products was studied using a newly developed testing device equipped with in-line sensors, in addition to the official compendial procedure for measuring the disintegration time. The in-line sensors were used to monitor the particle count and solution pH change to assess the onset and duration of disintegration. A relatively large variation was observed in the disintegration time of the tested drug products using the compendial method. The data collected using the in-line sensors suggested that all tested drug products exhibited almost instantaneous onset of disintegration, under 2 s, and a sharp drop in solution pH. The drop in pH was slower for tablets with slower disintegration. The in-house prepared alendronate test tablets also showed similar trends suggesting rapid solubilization of the drug contributed to the fast tablet disintegration. This research highlights the usefulness of the newly developed in-line analytical method in combination with the compendial method in providing a better understanding of the disintegration and the accompanying drug solubilization processes for fast disintegrating tablet drug products. Copyright © 2013 Wiley Periodicals, Inc.

  4. Using tablets to support self-regulated learning in a longitudinal integrated clerkship.

    PubMed

    Archbold Hufty Alegría, Dylan; Boscardin, Christy; Poncelet, Ann; Mayfield, Chandler; Wamsley, Maria

    2014-01-01

    Introduction The need to train physicians committed to learning throughout their careers has prompted medical schools to encourage the development and practice of self-regulated learning by students. Longitudinal integrated clerkships (LICs) require students to exercise self-regulated learning skills. As mobile tools, tablets can potentially support self-regulation among LIC students. Methods We provided 15 LIC students with tablet computers with access to the electronic health record (EHR), to track their patient cohort, and a multiplatform online notebook, to support documentation and retrieval of self-identified clinical learning issues. Students received a 1-hour workshop on the relevant features of the tablet and online notebook. Two focus groups with the students were used to evaluate the program, one early and one late in the year and were coded by two raters. Results Students used the tablet to support their self-regulated learning in ways that were unique to their learning styles and increased access to resources and utilization of down-time. Students who used the tablet to self-monitor and target learning demonstrated the utility of tablets as learning tools. Conclusions LICs are environments rich in opportunity for self-regulated learning. Tablets can enhance students' ability to develop and employ self-regulatory skills in a clinical context.

  5. Using tablets to support self-regulated learning in a longitudinal integrated clerkship.

    PubMed

    Alegría, Dylan Archbold Hufty; Boscardin, Christy; Poncelet, Ann; Mayfield, Chandler; Wamsley, Maria

    2014-01-01

    The need to train physicians committed to learning throughout their careers has prompted medical schools to encourage the development and practice of self-regulated learning by students. Longitudinal integrated clerkships (LICs) require students to exercise self-regulated learning skills. As mobile tools, tablets can potentially support self-regulation among LIC students. We provided 15 LIC students with tablet computers with access to the electronic health record (EHR), to track their patient cohort, and a multiplatform online notebook, to support documentation and retrieval of self-identified clinical learning issues. Students received a 1-hour workshop on the relevant features of the tablet and online notebook. Two focus groups with the students were used to evaluate the program, one early and one late in the year and were coded by two raters. Students used the tablet to support their self-regulated learning in ways that were unique to their learning styles and increased access to resources and utilization of down-time. Students who used the tablet to self-monitor and target learning demonstrated the utility of tablets as learning tools. LICs are environments rich in opportunity for self-regulated learning. Tablets can enhance students' ability to develop and employ self-regulatory skills in a clinical context.

  6. Using tablets to support self-regulated learning in a longitudinal integrated clerkship

    PubMed Central

    Alegría, Dylan Archbold Hufty; Boscardin, Christy; Poncelet, Ann; Mayfield, Chandler; Wamsley, Maria

    2014-01-01

    Introduction The need to train physicians committed to learning throughout their careers has prompted medical schools to encourage the development and practice of self-regulated learning by students. Longitudinal integrated clerkships (LICs) require students to exercise self-regulated learning skills. As mobile tools, tablets can potentially support self-regulation among LIC students. Methods We provided 15 LIC students with tablet computers with access to the electronic health record (EHR), to track their patient cohort, and a multiplatform online notebook, to support documentation and retrieval of self-identified clinical learning issues. Students received a 1-hour workshop on the relevant features of the tablet and online notebook. Two focus groups with the students were used to evaluate the program, one early and one late in the year and were coded by two raters. Results Students used the tablet to support their self-regulated learning in ways that were unique to their learning styles and increased access to resources and utilization of down-time. Students who used the tablet to self-monitor and target learning demonstrated the utility of tablets as learning tools. Conclusions LICs are environments rich in opportunity for self-regulated learning. Tablets can enhance students’ ability to develop and employ self-regulatory skills in a clinical context. PMID:24646438

  7. Tablet disintegration studied by high-resolution real-time magnetic resonance imaging.

    PubMed

    Quodbach, Julian; Moussavi, Amir; Tammer, Roland; Frahm, Jens; Kleinebudde, Peter

    2014-01-01

    The present work employs recent advances in high-resolution real-time magnetic resonance imaging (MRI) to investigate the disintegration process of tablets containing disintegrants. A temporal resolution of 75 ms and a spatial resolution of 80 × 80 µm with a section thickness of only 600 µm were achieved. The histograms of MRI videos were quantitatively analyzed with MATLAB. The mechanisms of action of six commercially available disintegrants, the influence of relative tablet density, and the impact of disintegrant concentration were examined. Crospovidone seems to be the only disintegrant acting by a shape memory effect, whereas the others mainly swell. A higher relative density of tablets containing croscarmellose sodium leads to a more even distribution of water within the tablet matrix but hardly impacts the disintegration kinetics. Increasing the polacrilin potassium disintegrant concentration leads to a quicker and more thorough disintegration process. Real-time MRI emerges as valuable tool to visualize and investigate the process of tablet disintegration.

  8. Stability and compatibility of tegaserod from crushed tablets mixed in beverages and foods.

    PubMed

    Carrier, Marie-Noëlle; Garinot, Olivier; Vitzling, Christian

    2004-06-01

    The stability and compatibility of tegaserod from crushed tablets in selected beverages and foods were studied. Suspensions of tegaserod maleate tablets containing 6 mg of the drug base were prepared by crushing the tablets and mixing the powder with tap water, apple juice, orange juice, milk, applesauce, yogurt, and chocolate-hazelnut spread. Drug stability, drug comparability, suspension homogeneity, and completeness of a dose were measured by high-performance liquid chromatography at intervals up to three days at 20-25 degrees C and 5 degrees C. In vitro dissolution profiles were determined for crushed tegaserod tablets in water, apple juice, orange juice, and applesauce. Tegaserod from crushed tablets was stable in and compatible with water, apple juice, orange juice, and applesauce, and the suspensions were homogeneous. The complete dose was delivered with these media. The dissolution profiles of crushed tegaserod tablets in water and in apple juice were comparable to those of intact tablets; the dissolution profiles in orange juice and applesauce were not comparable with those of intact tablets. The results with milk, yogurt, and chocolate-hazelnut spread as vehicles were inconclusive. The suspension in milk was not homogeneous, and the dose was incomplete. Tegaserod from crushed tablets was stable in and compatible with water, apple juice, orange juice, and applesauce, but the dissolution profile in orange juice or applesauce was not acceptable. Apple juice may be the preferred vehicle because it masks the drug's taste.

  9. Bronchoscopic and histological changes over time following acute ferrous sulphate tablet aspiration

    PubMed Central

    Maw, Matthew; Chiu, Robert; Lim, Albert Yick Hou

    2012-01-01

    An 84-year-old woman accidentally aspirated an iron tablet. She was successfully treated with early endobronchial removal of the iron tablet remnants, oral corticosteroids and antibiotics. We describe the bronchoscopic and histological changes over time following acute iron tablet aspiration and highlight the importance of early intervention to avoid complications. PMID:23257641

  10. Mimosa pudica seed mucilage: isolation; characterization and evaluation as tablet disintegrant and binder.

    PubMed

    Ahuja, Munish; Kumar, Ashok; Yadav, Parvinder; Singh, Kuldeep

    2013-06-01

    In the present study Mimosa pudica seed mucilage was isolated, characterized and evaluated as tablet binder and disintegrant. Several properties of mucilage like high swelling index and gelling nature prompted us to explore its applications as disintegrating and binding agent. Disintegrant properties were evaluated by formulating directly compressed hydrochlorothiazide tablets containing 1%-10% (w/w) of seed mucilage as disintegrant and compared with the standard disintegrants. The disintegration time of mucilage containing tablets was found to be in the order of 3%>1%>5%>7.5%>10%. On comparative evaluation with standard disintegrants, it was observed that the order of disintegration of tablets was Ac-Di-Soltablets using the Mimosa mucilage at 6%, 8%, and 10% (w/w) concentration as the binder and compared with tablets prepared using PVP-K25 (1.7%, w/w) and acacia (6.8%, w/w) as the binder. Mimosa mucilage at 10% (w/w) concentration provided tablets with adequate hardness and friability. In conclusion, M. pudica seed mucilage is a potential tablet disintegrant and binder. Copyright © 2013 Elsevier B.V. All rights reserved.

  11. Quantitative measurements of localized density variations in cylindrical tablets using X-ray microtomography.

    PubMed

    Busignies, Virginie; Leclerc, Bernard; Porion, Patrice; Evesque, Pierre; Couarraze, Guy; Tchoreloff, Pierre

    2006-08-01

    Direct compaction is a complex process that results in a density distribution inside the tablets which is often heterogeneous. Therefore, the density variations may affect the compact properties. A quantitative analysis of this phenomenon is still lacking. Recently, X-ray microtomography has been successfully used in pharmaceutical development to study qualitatively the impact of tablet shape and break-line in the density of pharmaceutical tablets. In this study, we evaluate the density profile in microcrystalline cellulose (Vivapur 12) compacts obtained at different mean porosity (ranging from 7.7% to 33.5%) using X-ray tomography technique. First, the validity of the Beer-Lambert law is studied. Then, density calibration is performed and density maps of cylindrical tablets are obtained and visualized using a process with colour-scale calibration plot which is explained. As expected, important heterogeneity in density is observed and quantified. The higher densities in peripheral region were particularly investigated and appraised in regard to the lower densities observed in the middle of the tablet. The results also underlined that in the case of pharmaceutical tablets, it is important to differentiate the mechanical properties representative of the total volume tablet and the mechanical properties that only characterize the tablet surface like the Brinell hardness measurements.

  12. Exploring the use of tablet PCs in veterinary medical education: opportunity or obstacle?

    PubMed

    Wang, Hong; Rush, Bonnie R; Wilkerson, Melinda; van der Merwe, Deon

    2014-01-01

    A tablet PC is a laptop computer with a touch screen and a digital pen or stylus that can be used for handwritten notes and drawings. The use of tablet PCs has been investigated in many disciplines such as engineering, mathematics, science, and education. The purpose of this article is to explore student and faculty attitudes toward and experiences with tablet PCs 6 years after the implementation of a tablet PC program in the College of Veterinary Medicine (CVM) at Kansas State University (K-State). This study reports that the use of tablet PCs has enhanced students' learning experiences through learner-interface interaction, learner-content interaction, learner-instructor interaction, and learner-learner interaction. This study also identifies digital distraction as the major negative experience with tablet PCs during class time. The tablet PC program provides CVM faculty the potential to pursue technology integration strategies that support expected learning outcomes and provides students the potential to develop self-monitoring and self-discipline skills that support learning with digital technologies.

  13. Active Learning with Ubiquitous Presenter and Tablet PCs

    NASA Astrophysics Data System (ADS)

    Price, Edward; Simon, B.

    2006-12-01

    Ubiquitous Presenter (UP)* is a digital presentation system that facilitates spontaneity and interactivity in the classroom. Using the system, an instructor with a Tablet PC can spontaneously modify prepared slides. Furthermore, students with web-enabled devices can add digital 'ink' or text to the instructor's slides and submit them to the instructor during class. We have used this system to facilitate interactive engagement techniques in an introductory physics class where approximately one-third of the students had access to a Tablet PC during class. Class time was used for Interactive Lecture Demonstrations, Peer Instruction, and group problem solving. We describe the implementation of these active learning activities with UP and Tablet PCs, show examples of student contributions, and describe the impact on the classroom setting. *http://up.ucsd.edu/about/

  14. Enhanced dissolution of sildenafil citrate as dry foam tablets.

    PubMed

    Sawatdee, Somchai; Atipairin, Apichart; Sae Yoon, Attawadee; Srichana, Teerapol; Changsan, Narumon

    2017-01-30

    Dry foam formulation technology is alternative approach to enhance dissolution of the drug. Sildenafil citrate was suspended in sodium dodecyl sulfate solution and adding a mixture of maltodextrin and mannitol as diluent to form a paste. Sildenafil citrate paste was passed through a nozzle spray bottle to obtain smooth foam. The homogeneous foam was dried in a vacuum oven and sieved to obtain dry foam granules. The granules were mixed with croscarmellose sodium, magnesium stearate and compressed into tablet. All formulations were evaluated for their physicochemical properties and dissolution profiles. All the tested excipients were compatible with sildenafil citrate by both differential scanning calorimetry (DSC) and infrared (IR) analysis. There are no X-ray diffraction (XRD) peaks representing crystals of sildenafil citrate observed form dry foam formulations. The hardness of tablets was about 5 kg, friability test <1% with a disintegration time <5 min. The sildenafil citrate dry foam tablet had higher dissolution rate in 0.1 N HCl in comparison with commercial sildenafil citrate tablet, sildenafil citrate prepared by direct compression and wet granulation method. Sildenafil citrate dry foam tablet with the high-level composition of surfactant, water and diluent showed enhanced dissolution rate than that of the lower-level composition of these excipients. This formulation was stable under accelerated conditions for at least 6 months.

  15. [Influence of polymer type on the physical properties and the release study of papaverine hydrochloride from tablets].

    PubMed

    Kasperek, Regina; Polski, Andrzej; Sobótka-Polska, Karolina; Poleszak, Ewa

    2014-01-01

    Polymers are widely used in drug manufacturing. Researchers studied their impact on the bioavailability of active substances or on physical properties of tablets for many years. To study the influence of polymer excipients, such as microcrystalline cellulose (Avicel PH 101, Avicel PH 102), croscarmellose sodium, crospovidone or polyvinylpyrrolidone, on the release profile of papaverine hydrochloride from tablets and on the physical properties of tablets. Six series of uncoated tablets were prepared by indirect method, with previous wet granulation. Tablets contained papaverine hydrochloride and various excipients. The physical properties of the prepared granules, tablets and the release profile of papaverine hydrochloride from tablets were examined. The content of papaverine hydrochloride from the release study were determined spectrophotometrically. All tablets met the pharmacopoeia requirements during following tests: the disintegration time of tablets, uncoated tablets resistance to abrasion, the weight uniformity and dose formulations, their dimensions, the resistance to crushing of tablets and the drug substance content in the tablet. In four cases more than 80% of papaverine was released up to 2 min, in one formula it was up to 5 min, and in last one up to 10 min. Tablets containing crospovidone disintegrated faster than tablets with croscarmellose sodium. Adding gelatinized starch to the tablet composition increased the disintegration time, hardness and delayed the release of papaverine. During the wet granulation process, granules containing polyvinylpyrrolidone were characterized by a suitable flow properties and slightly prolonged disintegration time. Tablets containing Avicel PH 102 compared to tablets with Avicel PH 101 had less weight loss during the test of mechanical resistance, improved hardness and faster release profile of papaverine from tablets.

  16. [Application of β-cyclodextrin in the formulation of ODT tablets containing ibuprofen].

    PubMed

    Zimmer, Łukasz; Kasperek, Regina; Poleszak, Ewa

    2014-01-01

    Oral disintegrating tablet (ODT) dissolves or disintegrates in saliva and then it is swallowed. Diluent in direct compression formulation has a dual role: it increases bulk of the dosage form and it promotes binding of the constituent particles of the formulation. Hence, selection of diluent is important in tablets produced by direct compression method. The aim of this work was to exame feasibility of preparing and optimizing oral disintegrating tablet formulation using β-cyclodextrin as a diluent. 400 mg round tablets were prepared by direct compression method on single punch tablet press using flat plain-face. 60% β-CD and MCC (microcrystalline cellulose - MCC-Vivapur 102) were used at different proportions for all the formulations. 5% of Kollidon CL was added as superdisintegrant. The eight formulations prepared were assessed for weight variation, thickness, disintegration time, hardness and dissolution rate according to FP IX. A dissolution test was performed at 37ºC using the paddle method at 50 rpm with 900 mL phosphate buffer (pH 6.8) as a dissolution medium. The content of ibuprofen sodium was found inside the ± 5% of the theoretical value. Hardness values of presented tablets were in the range 0.11-0.15 kG/mm2. Friability of the tablets lower than 1% indicates that the developed formulations can be processed and handled without excessive care. Disintegration time was in the range of 86 to 161 s. The results confirm the good mechanical properties of tablets containing β-CD. A composition with 20% β-CD and 40% MCC fulfilled a maximum requisite of an optimum formulation. These properties were similar to Ludiflash, the formulation used for comparison purposes. In the present study, higher concentration of β cyclodextrin was found to improve the hardness of tablets without increasing the disintegration time.

  17. Lyophilized mucoadhesive-dendrimer enclosed matrix tablet for extended oral delivery of albendazole.

    PubMed

    Mansuri, Shakir; Kesharwani, Prashant; Tekade, Rakesh Kumar; Jain, Narendra Kumar

    2016-05-01

    Dendrimers are multifunctional carriers widely employed for delivering drugs in a variety of disease conditions including HIV/AIDS and cancer. Albendazole (ABZ) is a commonly used anthelmintic drug in human as well as veterinary medicine. In this investigation, ABZ was formulated as a "muco-dendrimer" based sustained released tablet. The mucoadhesive complex was synthesized by anchoring chitosan to fifth generation PPI dendrimer (Muco-PPI) and characterized by UV, FTIR, (1)H NMR spectroscopy and electron microscopy. ABZ was entrapped inside Muco-PPI followed by lyophilization and tableting as matrix tablet. A half-life (t1/2) of 8.06±0.15, 8.17±0.47, 11.04±0.73, 11.49±0.92, 12.52±1.04 and 16.9±1.18h was noted for ABZ (free drug), conventional ABZ tablet (F1), conventional ABZ matrix tablet (F2), PPI-ABZ complex, PPI-ABZ matrix tablet (F3) and Muco-PPI-ABZ matrix tablet (F4), respectively. Thus the novel mucoadhesive-PPI based formulation of ABZ (F4) increased the t1/2 of ABZ significantly by almost twofold as compared to the administration of free drug. The in vivo drug release data showed that the Muco-PPI based formulations have a significantly higher Cmax (2.40±0.02μg/mL) compared with orally administered free ABZ (0.19±0.07μg/mL) as well as conventional tablet (0.20±0.05μg/mL). In addition, the Muco-PPI-ABZ matrix tablet displayed increased mean residence time (MRT) and is therefore a potential candidate to appreciably improve the pharmacokinetic profile of ABZ. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Vardenafil orodispersible tablet.

    PubMed

    Sanford, Mark

    2012-01-01

    Vardenafil orodispersible tablet (ODT) is a supralingual formulation of vardenafil that is available for the on-demand treatment of erectile dysfunction. The pharmacokinetics of vardenafil ODT are not equivalent to those of the vardenafil film-coated tablet in that the ODT formulation provides consistently greater vardenafil systemic exposure. Therefore, the two formulations are not interchangeable. The efficacy of on-demand vardenafil ODT 10 mg was established in the POTENT I and II studies, which were 6-week, randomized, double-blind, multinational trials in men with erectile dysfunction of at least 6 months duration. In both trials, vardenafil ODT improved erectile function significantly more than placebo, as indicated by International Index of Erectile Function-Erectile Function subscale scores at week 12 and overall erection success rates during treatment according to responses to questions 2 and 3 of the Sexual Encounter Profile (coprimary endpoints). In a pooled analysis of both trials, vardenafil ODT improved erectile function regardless of age, severity of erectile dysfunction at baseline or the presence or absence of underlying medical conditions. Vardenafil ODT was generally well tolerated in clinical trials, including in men aged ≥65 years, and adverse events were mostly mild or moderate in severity.

  19. Graphics Tablet Technology in Second Year Thermal Engineering Teaching

    ERIC Educational Resources Information Center

    Carrillo, Antonio; Cejudo, José Manuel; Domínguez, Fernando; Rodríguez, Eduardo

    2013-01-01

    Graphics tablet technology is well known in markets such as manufacturing, graphics arts and design but it has not yet found widespread acceptance for university teaching. A graphics tablet is an affordable teaching tool that combines the best features from traditional and new media. It allows developing a progressive, interactive lecture (as a…

  20. A study of compressibility and compactibility of directly compressible tableting materials containing tramadol hydrochloride.

    PubMed

    Mužíková, Jitka; Kubíčková, Alena

    2016-09-01

    The paper evaluates and compares the compressibility and compactibility of directly compressible tableting materials for the preparation of hydrophilic gel matrix tablets containing tramadol hydrochloride and the coprocessed dry binders Prosolv® SMCC 90 and Disintequik™ MCC 25. The selected types of hypromellose are Methocel™ Premium K4M and Methocel™ Premium K100M in 30 and 50 % concentrations, the lubricant being magnesium stearate in a 1 % concentration. Compressibility is evaluated by means of the energy profile of compression process and compactibility by the tensile strength of tablets. The values of total energy of compression and plasticity were higher in the tableting materials containing Prosolv® SMCC 90 than in those containing Disintequik™ MCC 25. Tramadol slightly decreased the values of total energy of compression and plasticity. Tableting materials containing Prosolv® SMCC 90 yielded stronger tablets. Tramadol decreased the strength of tablets from both coprocessed dry binders.

  1. Implementation of Quality by Design for Formulation of Rebamipide Gastro-retentive Tablet.

    PubMed

    Ha, Jung-Myung; Seo, Jeong-Woong; Kim, Su-Hyeon; Kim, Ju-Young; Park, Chun-Woong; Rhee, Yun-Seok; Park, Eun-Seok

    2017-11-01

    The purpose of the present study was to develop a rebamipide (RBM) gastro-retentive (GR) tablet by implementing quality by design (QbD). RBM GR tablets were prepared using a sublimation method. Quality target product profile (QTPP) and critical quality attributes (CQAs) of the RBM GR tablets were defined according to the preliminary studies. Factors affecting the CQAs were prioritized using failure mode and effects analysis (FMEA). Design space and optimum formulation were established through a mixture design. The validity of the design space was confirmed using runs within the area. The QTPP of the RBM GR tablets was the orally administered GR tablet containing 300 mg of RBM taken once daily. Based on the QTPP, dissolution rate, tablet friability, and floating property were chosen as CQAs. According to the risk assessment, the amount of sustained-release agent, sublimating material, and diluent showed high-risk priority number (RPN) values above 40. Based on the RPN, these factors were further investigated using mixture design methodology. Design space of formulations was depicted as an overlaid contour plot and the optimum formulation to satisfy the desired responses was obtained by determining the expected value of each response. The similarity factor (f2) of the release profile between predicted response and experimental response was 89.463, suggesting that two release profiles are similar. The validity of the design space was also confirmed. Consequently, we were able to develop the RBM GR tablets by implementing the QbD concept. These results provide useful information for development of tablet formulations using the QbD.

  2. Analysis of ecstasy tablets: comparison of reflectance and transmittance near infrared spectroscopy.

    PubMed

    Schneider, Ralph Carsten; Kovar, Karl-Artur

    2003-07-08

    Calibration models for the quantitation of commonly used ecstasy substances have been developed using near infrared spectroscopy (NIR) in diffuse reflectance and in transmission mode by applying seized ecstasy tablets for model building and validation. The samples contained amphetamine, N-methyl-3,4-methylenedioxy-amphetamine (MDMA) and N-ethyl-3,4-methylenedioxy-amphetamine (MDE) in different concentrations. All tablets were analyzed using high performance liquid chromatography (HPLC) with diode array detection as reference method. We evaluated the performance of each NIR measurement method with regard to its ability to predict the content of each tablet with a low root mean square error of prediction (RMSEP). Best calibration models could be generated by using NIR measurement in transmittance mode with wavelength selection and 1/x-transformation of the raw data. The models build in reflectance mode showed higher RMSEPs using as data pretreatment, wavelength selection, 1/x-transformation and a second order Savitzky-Golay derivative with five point smoothing was applied to obtain the best models. To estimate the influence of inhomogeneities in the illegal tablets, a calibration of the destroyed, i.e. triturated samples was build and compared to the corresponding data of the whole tablets. The calibrations using these homogenized tablets showed lower RMSEPs. We can conclude that NIR analysis of ecstasy tablets in transmission mode is more suitable than measurement in diffuse reflectance to obtain quantification models for their active ingredients with regard to low errors of prediction. Inhomogeneities in the samples are equalized when measuring the tablets as powdered samples.

  3. 3D extrusion printing of high drug loading immediate release paracetamol tablets.

    PubMed

    Khaled, Shaban A; Alexander, Morgan R; Wildman, Ricky D; Wallace, Martin J; Sharpe, Sonja; Yoo, Jae; Roberts, Clive J

    2018-03-01

    The manufacture of immediate release high drug loading paracetamol oral tablets was achieved using an extrusion based 3D printer from a premixed water based paste formulation. The 3D printed tablets demonstrate that a very high drug (paracetamol) loading formulation (80% w/w) can be printed as an acceptable tablet using a method suitable for personalisation and distributed manufacture. Paracetamol is an example of a drug whose physical form can present challenges to traditional powder compression tableting. Printing avoids these issues and facilitates the relatively high drug loading. The 3D printed tablets were evaluated for physical and mechanical properties including weight variation, friability, breaking force, disintegration time, and dimensions and were within acceptable range as defined by the international standards stated in the United States Pharmacopoeia (USP). X-ray Powder Diffraction (XRPD) was used to identify the physical form of the active. Additionally, XRPD, Attenuated Total Reflectance Fourier Transform Infrared spectroscopy (ATR-FTIR) and differential scanning calorimetry (DSC) were used to assess possible drug-excipient interactions. The 3D printed tablets were evaluated for drug release using a USP dissolution testing type I apparatus. The tablets showed a profile characteristic of the immediate release profile as intended based upon the active/excipient ratio used with disintegration in less than 60 s and release of most of the drug within 5 min. The results demonstrate the capability of 3D extrusion based printing to produce acceptable high-drug loading tablets from approved materials that comply with current USP standards. Copyright © 2018 Elsevier B.V. All rights reserved.

  4. Optical coherence tomography for non-destructive analysis of coatings in pharmaceutical tablets

    NASA Astrophysics Data System (ADS)

    Markl, Daniel; Hannesschläger, Günther; Sacher, Stephan; Khinast, Johannes G.; Leitner, Michael

    2013-04-01

    Tablet coating is a common pharmaceutical technique to apply a thin continuous layer of solid on the top of a tablet or a granule containing active pharmaceutical ingredients (APIs). Coating thickness and homogeneity are critical parameters regarding the drug release rate, and consequently a direct or indirect monitoring strategy of these critical process parameters is essential. With the aid of Optical Coherence Tomography (OCT) it is not only possible to measure the absolute coating thickness, but also to detect inhomogeneities in the coating or substrate material. In this work the possible application of OCT as in-line method for monitoring pharmaceutical tablet film coating is studied. Firstly, the feasibility of OCT for analysis tablet coating is examined. Seven different commercially available film-coated tablets with different shapes, formulations and coating thicknesses were investigated off-line. OCT images were acquired by two different spectral-domain OCT systems operating at center wavelengths of 830 and 1325 nm. Since the images of both systems allow the analysis of the coatings, the OCT system employing the shorter wavelength and thus providing a higher axial resolution was selected for the further experiments. The influence of a moving tablet bed on OCT images was analyzed by considering a static tablet bed and moving the sensor head along the tablet bed. The ability to analyze the coating homogeneity is limited to a speed up to 0.3 m/s. However, determining the coating thickness and inter-coating uniformity is still possible up to a speed of 0.7 m/s.

  5. Effect of Qing Nao tablet on blood stasis model of mice

    NASA Astrophysics Data System (ADS)

    Kong, Xuejun; Hao, Shaojun; Wang, Hongyu; Liu, Xiaobin; Xie, Guoqi; Li, Wenjun; Zhang, Zhengchen

    2018-04-01

    To investigate the effect of Qing Nao tablet on mouse model of blood stasis syndrome, 60 mice, male and female, were randomly divided into 6 groups, were fed with large, small doses of Qing Nao tablet suspension, Naoluotong saline suspension and the same volume (group 2, 0.1ml/10g), administer 1 times daily, orally for 15 days. Intragastric administration for first days, in addition to the 1 group saline group every day in the hind leg intramuscular saline, the other 5 groups each rat day hind leg muscle injection of dexamethasone 0.8mg/kg intramuscular injection every day, 1 times, 15 days. 1 hour continuous intramuscular injection and intramuscular drug perfusion on the sixteenth day after mice. The eyeball blood, heparin after whole blood viscosity test. Compared with the control group, model group, high and low shear viscosity were significantly increased (P<0.01), indicating that the model was successful. Compared with the model group, high dose group and Qing Nao tablet Naoluotong group can significantly reduce the viscosity at high shear and (P<0.01), middle dose Qing Nao tablet group can significantly reduce high shear and shear viscosity (P<0.05); large, middle dose Qing Nao tablet group can significantly reduce the low shear viscosity (P<0.05), Naoluotong group can significantly reduce the low shear viscosity (P<0.01); low dose Qing Nao tablet group were lower high cut, low shear viscosity and trend The potential (P>0.05). The Qing Nao tablet has a good effect on the model of blood stasis in mice.

  6. Raman spectroscopy for the analytical quality control of low-dose break-scored tablets.

    PubMed

    Gómez, Diego A; Coello, Jordi; Maspoch, Santiago

    2016-05-30

    Quality control of solid dosage forms involves the analysis of end products according to well-defined criteria, including the assessment of the uniformity of dosage units (UDU). However, in the case of break-scored tablets, given that tablet splitting is widespread as a means to adjust doses, the uniform distribution of the active pharmaceutical ingredient (API) in all the possible fractions of the tablet must be assessed. A general procedure to accomplish with both issues, using Raman spectroscopy, is presented. It is based on the acquisition of a collection of spectra in different regions of the tablet, that later can be selected to determine the amount of API in the potential fractions that can result after splitting. The procedure has been applied to two commercial products, Sintrom 1 and Sintrom 4, with API (acenocoumarol) mass proportion of 2% and 0.7% respectively. Partial Least Squares (PLS) calibration models were constructed for the quantification of acenocoumarol in whole tablets using HPLC as a reference analytical method. Once validated, the calibration models were used to determine the API content in the different potential fragments of the scored Sintrom 4 tablets. Fragment mass measurements were also performed to estimate the range of masses of the halves and quarters that could result after tablet splitting. The results show that Raman spectroscopy can be an alternative analytical procedure to assess the uniformity of content, both in whole tablets as in its potential fragments, and that Sintrom 4 tablets can be perfectly split in halves, but some cautions have to be taken when considering the fragmentation in quarters. A practical alternative to the use of UDU test for the assessment of tablet fragments is proposed. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Tablet computer enhanced training improves internal medicine exam performance.

    PubMed

    Baumgart, Daniel C; Wende, Ilja; Grittner, Ulrike

    2017-01-01

    Traditional teaching concepts in medical education do not take full advantage of current information technology. We aimed to objectively determine the impact of Tablet PC enhanced training on learning experience and MKSAP® (medical knowledge self-assessment program) exam performance. In this single center, prospective, controlled study final year medical students and medical residents doing an inpatient service rotation were alternatingly assigned to either the active test (Tablet PC with custom multimedia education software package) or traditional education (control) group, respectively. All completed an extensive questionnaire to collect their socio-demographic data, evaluate educational status, computer affinity and skills, problem solving, eLearning knowledge and self-rated medical knowledge. Both groups were MKSAP® tested at the beginning and the end of their rotation. The MKSAP® score at the final exam was the primary endpoint. Data of 55 (tablet n = 24, controls n = 31) male 36.4%, median age 28 years, 65.5% students, were evaluable. The mean MKSAP® score improved in the tablet PC (score Δ + 8 SD: 11), but not the control group (score Δ- 7, SD: 11), respectively. After adjustment for baseline score and confounders the Tablet PC group showed on average 11% better MKSAP® test results compared to the control group (p<0.001). The most commonly used resources for medical problem solving were journal articles looked up on PubMed or Google®, and books. Our study provides evidence, that tablet computer based integrated training and clinical practice enhances medical education and exam performance. Larger, multicenter trials are required to independently validate our data. Residency and fellowship directors are encouraged to consider adding portable computer devices, multimedia content and introduce blended learning to their respective training programs.

  8. Tablet computer enhanced training improves internal medicine exam performance

    PubMed Central

    Wende, Ilja; Grittner, Ulrike

    2017-01-01

    Background Traditional teaching concepts in medical education do not take full advantage of current information technology. We aimed to objectively determine the impact of Tablet PC enhanced training on learning experience and MKSAP® (medical knowledge self-assessment program) exam performance. Methods In this single center, prospective, controlled study final year medical students and medical residents doing an inpatient service rotation were alternatingly assigned to either the active test (Tablet PC with custom multimedia education software package) or traditional education (control) group, respectively. All completed an extensive questionnaire to collect their socio-demographic data, evaluate educational status, computer affinity and skills, problem solving, eLearning knowledge and self-rated medical knowledge. Both groups were MKSAP® tested at the beginning and the end of their rotation. The MKSAP® score at the final exam was the primary endpoint. Results Data of 55 (tablet n = 24, controls n = 31) male 36.4%, median age 28 years, 65.5% students, were evaluable. The mean MKSAP® score improved in the tablet PC (score Δ + 8 SD: 11), but not the control group (score Δ- 7, SD: 11), respectively. After adjustment for baseline score and confounders the Tablet PC group showed on average 11% better MKSAP® test results compared to the control group (p<0.001). The most commonly used resources for medical problem solving were journal articles looked up on PubMed or Google®, and books. Conclusions Our study provides evidence, that tablet computer based integrated training and clinical practice enhances medical education and exam performance. Larger, multicenter trials are required to independently validate our data. Residency and fellowship directors are encouraged to consider adding portable computer devices, multimedia content and introduce blended learning to their respective training programs. PMID:28369063

  9. A new formulation for orally disintegrating tablets using a suspension spray-coating method.

    PubMed

    Okuda, Y; Irisawa, Y; Okimoto, K; Osawa, T; Yamashita, S

    2009-12-01

    The aim of this study was to design a new orally disintegrating tablet (ODT) that has high tablet hardness and a fast oral disintegration rate using a new preparation method. To obtain rapid disintegration granules (RDGs), a saccharide, such as trehalose, mannitol, or lactose, was spray-coated with a suspension of corn starch using a fluidized-bed granulator (suspension method). As an additional disintegrant, crospovidone, light anhydrous silicic acid, or hydroxypropyl starch was also included in the suspension. The RDGs obtained possessed extremely large surface areas, narrow particle size distribution, and numerous micro-pores. When tabletting these RDGs, it was found that the RDGs increased tablet hardness by decreasing plastic deformation and increasing the contact frequency between granules. In all tablets, a linear relationship was observed between tablet hardness and oral disintegration time. From each linear correlation line, a slope (D/H value) and an intercept (D/H(0) value) were calculated. Tablets with small D/H and D/H(0) values could disintegrate immediately in the oral cavity regardless of the tablet hardness and were considered to be appropriate for ODTs. Therefore, these values were used as key parameters to select better ODTs. Of all the RDGs prepared in this study, mannitol spray-coated with a suspension of corn starch and crospovidone (2.5:1 w/w ratio) showed most appropriate properties for ODTs; fast in vivo oral disintegration time, and high tablet hardness. In conclusion, this simple method to prepare superior formulations for new ODTs was established by spray-coating mannitol with a suspension of appropriate disintegrants.

  10. Orodispersible films and tablets with prednisolone microparticles.

    PubMed

    Brniak, Witold; Maślak, Ewelina; Jachowicz, Renata

    2015-07-30

    Orodispersible tablets (ODTs) and orodispersible films (ODFs) are solid oral dosage forms disintegrating or dissolving rapidly when placed in the mouth. One of the main issues related to their preparation is an efficient taste masking of a bitter drug substance. Therefore, the aim of this study was to prepare and evaluate the microparticles intended to mask a bitter taste of the prednisolone and use them in further preparation of two orodispersible dosage forms. Microparticles based on the Eudragit E PO or E 100 as a taste-masking agent were prepared with spray-drying technique. Tablets containing microparticles, co-processed ODT excipient Pharmaburst, and lubricant were directly compressed with single-punch tablet press. Orodispersible films were prepared by casting polymeric solutions of hydroxypropyl methylcellulose containing uniformly dispersed microparticles. Physicochemical properties of microparticles were evaluated, as well as mechanical properties analysis, disintegration time measurements and dissolution tests were performed for prepared dosage forms. Both formulations showed good mechanical resistance while maintaining excellent disintegration properties. The dissolution studies showed good masking properties of microparticles with Eudragit E 100. The amount of prednisolone released during the first minute in phosphate buffer 6.8 was around 0.1%. After incorporation into the orodispersible forms, the amount of released prednisolone increased significantly. It was probably the effect of faster microparticles wetting in orodispersible forms and their partial destruction by compression force during tableting process. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Pharmacokinetics of hydrocodone extended-release tablets formulated with different levels of coating to achieve abuse deterrence compared with a hydrocodone immediate-release/acetaminophen tablet in healthy subjects.

    PubMed

    Darwish, Mona; Bond, Mary; Tracewell, William; Robertson, Philmore; Yang, Ronghua

    2015-01-01

    A hydrocodone extended-release (ER) formulation employing the CIMA(®) Abuse-Deterrence Technology platform was developed to provide resistance against rapid release of hydrocodone when tablets are comminuted or taken with alcohol. This study evaluated the pharmacokinetics of three hydrocodone ER tablet prototypes with varying levels of polymer coating to identify the prototype expected to have the greatest abuse deterrence potential based on pharmacokinetic characteristics that maintain systemic exposure to hydrocodone comparable to that of a commercially available hydrocodone immediate-release (IR) product. In this four-period crossover study, healthy subjects aged 18-45 years were randomized to receive a single intact, oral 45-mg tablet of one of three hydrocodone ER prototypes (low-, intermediate-, or high-level coating) or an intact, oral tablet of hydrocodone IR/acetaminophen (APAP) 10/325 mg every 6 h until four tablets were administered, with each of the four treatments administered once over the four study periods. Dosing periods were separated by a minimum 5-day washout. Naltrexone 50 mg was administered to block opioid receptors. Blood samples for pharmacokinetic assessments were collected predose and through 72 h postdose. Parameters assessed included maximum observed plasma hydrocodone concentration (C(max)), time to C(max) (t(max)), and area under the concentration-time curve from time 0 to infinity (AUC(0-∞)). Mean C(max) values were 49.2, 32.6, and 28.4 ng/mL for the low-, intermediate-, and high-level coating hydrocodone ER tablet prototypes, respectively, and 37.3 ng/mL for the hydrocodone IR/APAP tablet; respective median t(max) values were 5.9, 8.0, 8.0, and 1.0 h. Total systemic exposure to hydrocodone (AUC(0-∞)) was comparable between hydrocodone ER tablet prototypes (640, 600, and 578 ng·h/mL, respectively) and hydrocodone IR/APAP (581 ng·h/mL). No serious adverse events or deaths were reported. The most common adverse events included

  12. 3D Printing Factors Important for the Fabrication of Polyvinylalcohol Filament-Based Tablets.

    PubMed

    Tagami, Tatsuaki; Fukushige, Kaori; Ogawa, Emi; Hayashi, Naomi; Ozeki, Tetsuya

    2017-01-01

    Three-dimensional (3D) printers have been applied in many fields, including engineering and the medical sciences. In the pharmaceutical field, approval of the first 3D-printed tablet by the U.S. Food and Drug Administration in 2015 has attracted interest in the manufacture of tablets and drugs by 3D printing techniques as a means of delivering tailor-made drugs in the future. In current study, polyvinylalcohol (PVA)-based tablets were prepared using a fused-deposition-modeling-type 3D printer and the effect of 3D printing conditions on tablet production was investigated. Curcumin, a model drug/fluorescent marker, was loaded into PVA-filament. We found that several printing parameters, such as the rate of extruding PVA (flow rate), can affect the formability of the resulting PVA-tablets. The 3D-printing temperature is controlled by heating the print nozzle and was shown to affect the color of the tablets and their curcumin content. PVA-based infilled tablets with different densities were prepared by changing the fill density as a printing parameter. Tablets with lower fill density floated in an aqueous solution and their curcumin content tended to dissolve faster. These findings will be useful in developing drug-loaded PVA-based 3D objects and other polymer-based articles prepared using fused-deposition-modeling-type 3D printers.

  13. Colon targeted guar gum compression coated tablets of flurbiprofen: formulation, development, and pharmacokinetics.

    PubMed

    Vemula, Sateesh Kumar; Bontha, Vijaya Kumar

    2013-01-01

    The rationale of the present study is to formulate flurbiprofen colon targeted compression coated tablets using guar gum to improve the therapeutic efficacy by increasing drug levels in colon, and also to reduce the side effects in upper gastrointestinal tract. Direct compression method was used to prepare flurbiprofen core tablets, and they were compression coated with guar gum. Then the tablets were optimized with the support of in vitro dissolution studies, and further it was proved by pharmacokinetic studies. The optimized formulation (F4) showed almost complete drug release in the colon (99.86%) within 24 h without drug loss in the initial lag period of 5 h (only 6.84% drug release was observed during this period). The pharmacokinetic estimations proved the capability of guar gum compression coated tablets to achieve colon targeting. The C(max) of colon targeted tablets was 11956.15 ng/mL at T max of 10 h whereas it was 15677.52 ng/mL at 3 h in case of immediate release tablets. The area under the curve for the immediate release and compression coated tablets was 40385.78 and 78214.50 ng-h/mL and the mean resident time was 3.49 and 10.78 h, respectively. In conclusion, formulation of guar gum compression coated tablets was appropriate for colon targeting of flurbiprofen.

  14. Tablet mechanics depend on nano and micro scale adhesion, lubrication and structure.

    PubMed

    Badal Tejedor, Maria; Nordgren, Niklas; Schuleit, Michael; Rutland, Mark W; Millqvist-Fureby, Anna

    2015-01-01

    Tablets are the most convenient form for drug administration. However, despite the ease of manufacturing problems such as powder adhesion occur during the production process. This study presents surface and structural characterization of tablets formulated with commonly used excipients (microcrystalline cellulose (MCC), lactose, mannitol, magnesium (Mg) stearate) pressed under different compaction conditions. Tablet surface analyses were performed with scanning electron microscopy (SEM), profilometry and atomic force microscopy (AFM). The mechanical properties of the tablets were evaluated with a tablet hardness test. Local adhesion detected by AFM decreased when Mg stearate was present in the formulation. Moreover, the tablet strength of plastically deformable excipients such as MCC was significantly decreased after addition of Mg stearate. Combined these facts indicate that Mg stearate affects the particle-particle bonding and thus elastic recovery. The MCC excipient also displayed the highest hardness which is characteristic for a highly cohesive material. This is discussed in the view of the relatively high adhesion found between MCC and a hydrophilic probe at the nanoscale using AFM. In contrast, the tablet strength of brittle materials like lactose and mannitol is unaffected by Mg stearate. Thus fracture occurs within the excipient particles and not at particle boundaries, creating new surfaces not previously exposed to Mg stearate. Such uncoated surfaces may well promote adhesive interactions with tools during manufacture. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Roll Compaction and Tableting of High Loaded Metformin Formulations Using Efficient Binders.

    PubMed

    Arndt, Oscar-Rupert; Kleinebudde, Peter

    2018-04-23

    Metformin has a poor tabletability and flowability. Therefore, metformin is typically wet granulated with a binder before tableting. To save production costs, it would be desirable to implement a roll compaction/dry granulation (RCDG) process for metformin instead of using wet granulation. In order to implement RCDG, the efficiency of dry binders is crucial to ensure a high drug load and suitable properties of dry granules and tablets. This study evaluates dry granules manufactured by RCDG and subsequently tableting of high metformin content formulations (≥ 87.5%). Based on previous results, fine particle grades of hydroxypropylcellulose and copovidone in different fractions were compared as dry binders. The formulations are suitable for RCDG and tableting. Furthermore, results can be connected to in-die and out-of-die compressibility analysis. The addition of 7% of dry binder is a good compromise to generate sufficient mechanical properties on the one hand, but also to save resources and ensure a high metformin content on the other hand. Hydroxypropylcellulose was more efficient in terms of granule size, tensile strength and friability. Three percent croscarmellose was added to reach the specifications of the US Pharmacopeia regarding dissolution. The final formulation has a metformin content of 87.5%. A loss in tabletability does not occur for granules compressed at different specific compaction forces, which displays a robust tensile strength of tablets independent of the granulation process.

  16. Design and evaluation of enteric-coated tablets for rifampicin and isoniazid combinations.

    PubMed

    Wang, Yongjun; Liu, Hongzhuo; Liu, Kai; Sun, Jin; He, Zhonggui

    2013-01-01

    In order to improve the bioavailability of rifampicin (RIF) from rifampicin and isoniazid (INH) combination formulations, the physicochemical characteristics of RIF, stability of RIF in different pH buffers in the presence of INH, as well as the effect of particle size of RIF materials on the dissolution rate were investigated. On the basis of the above examinations, enteric-coated tablets for RIF and INH combinations were designed and prepared. RIF showed low solubility and high apparent distribution coefficient in the intestinal pH (pH 4.0-7.4). With the decrease in pH, the degradation of RIF increase and the presence of INH deepen the degradation. Enteric-coated tablets were prepared after grinding the RIF materials by dry granulation technique. The pharmacokinetics of RIF and INH of self-made enteric-coated tablets in dogs were studied by comparing with the reference tablets. The AUC(0-48) of RIF in both reference and test tablets were 304.77 ± 42.27 and 353.79 ± 31.63 µg·h·mL(-1), respectively. The AUC(0-48) of INH in both reference and test tablets were 17.14 ± 8.59 and 19.62 ± 10.57 µg·h·mL(-1), respectively. Enteric-coated tablets may minimize the decomposition of RIF in gastrointestinal tract and improve the bioavailability.

  17. FDA-Approved Natural Polymers for Fast Dissolving Tablets

    PubMed Central

    Alam, Md Tausif; Parvez, Nayyar; Sharma, Pramod Kumar

    2014-01-01

    Oral route is the most preferred route for administration of different drugs because it is regarded as safest, most convenient, and economical route. Fast disintegrating tablets are very popular nowadays as they get dissolved or facilely disintegrated in mouth within few seconds of administration without the need of water. The disadvantages of conventional dosage form, especially dysphagia (arduousness in swallowing), in pediatric and geriatric patients have been overcome by fast dissolving tablets. Natural materials have advantages over synthetic ones since they are chemically inert, non-toxic, less expensive, biodegradable and widely available. Natural polymers like locust bean gum, banana powder, mango peel pectin, Mangifera indica gum, and Hibiscus rosa-sinenses mucilage ameliorate the properties of tablet and utilized as binder, diluent, and superdisintegrants increase the solubility of poorly water soluble drug, decrease the disintegration time, and provide nutritional supplement. Natural polymers are obtained from the natural origin and they are cost efficacious, nontoxic, biodegradable, eco-friendly, devoid of any side effect, renewable, and provide nutritional supplement. It is proved from the studies that natural polymers are more safe and efficacious than the synthetic polymers. The aim of the present article is to study the FDA-approved natural polymers utilized in fast dissolving tablets. PMID:26556207

  18. Exploring the Use of Tablets for Student Teaching Supervision

    ERIC Educational Resources Information Center

    Johnson, Joseph A.; Wesley, Whitney M.; Yerrick, Randy

    2016-01-01

    While research on the use of tablets in the field of education is emerging, existing research on the use of this tool for the purposes of student teaching supervision is very limited. This study aimed to explore the application of iPad tablets for student teacher supervision in a teacher preparation program at a large state university in the…

  19. How Do Second Grade Students in Primary Schools Use and Perceive Tablets?

    ERIC Educational Resources Information Center

    Karalar, Halit; Sidekli, Sabri

    2017-01-01

    In the life of students who are named digitally born in this era, tablets have a crucial role. The aim of this study, which is designed as a case study model, is to determine the use of tablet by second grade students and it aims to reveal their perception towards tablets via metaphors. 63-second grade students are participated in this study in…

  20. Membrane formation and drug loading effects in high amylose starch tablets studied by NMR imaging.

    PubMed

    Thérien-Aubin, Héloïse; Zhu, X X; Ravenelle, François; Marchessault, Robert H

    2008-04-01

    Cross-linked high amylose starch is used as an excipient in the preparation of pharmaceutical tablets for the sustained release of drugs. NMR imaging with contrast enhanced by proton density and by self-diffusion coefficient was used to follow the water uptake and swelling, two critical parameters controlling the drug release of the cross-linked starch tablets containing 10 wt % of ciprofloxacin and of acetaminophen, respectively. The drug-loaded tablets were studied in a H2O/D2O mixture at 37 degrees C in comparison to the tablets without any drug loading. The diffusion of water in the tablets all showed a Fickian behavior, but the kinetics of water uptake was faster in the case of the drug-loaded tablets. The formation of a membrane at the water/tablet interface was observed.

  1. Pharmacokinetics of fixed-dose combinations of empagliflozin/metformin compared with individual tablets in healthy subjects.

    PubMed

    Rojas, Christina; Link, Jasmin; Meinicke, Thomas; Macha, Sreeraj

    2016-04-01

    To compare the pharmacokinetics of fixed-dose combination (FDC) tablets of empagliflozin/metformin with individual tablets taken together. In 3 randomized, open-label studies, healthy subjects received a single FDC tablet of empagliflozin/metformin in 1 of 6 dose combinations (empagliflozin 12.5 mg or 5 mg; metformin 500 mg, 850 mg, or 1,000 mg) in 1 period and the individual tablets taken together under fed conditions in another period. Empagliflozin 12.5 mg/metformin 1,000 mg FDC and individual tablets were also given under fasted conditions. Adjusted geometric mean ratios (GMRs) of empagliflozin area under the plasma concentration-time curve (AUC(0-∞)) for the FDCs vs. individual tablets ranged from 97.92 to 106.00%, and 90% CIs ranged from 93.53 to 109.39%. Adjusted GMRs of empagliflozin maximum plasma concentrations (C(max)) for the FDCs vs. individual tablets ranged from 100.97 to 106.52%, and 90% CIs ranged from 95.86 to 118.35%. Adjusted GMRs of metformin AUC(0-∞) for the FDCs vs. individual tablets ranged from 96.25 to 101.61%, and 90% CIs ranged from 88.54 to 106.62%. Adjusted GMRs of metformin C(max) for the FDCs vs. individual tablets ranged from 93.83 to 102.95%, and 90% CIs ranged from 88.01 to 109.08%. Bioequivalence was also established under fasted conditions for empagliflozin 12.5 mg/metformin 1,000 mg FDC vs. individual tablets taken together. All treatments were well tolerated. Empagliflozin/metformin FDC tablets were found to be bioequivalent to individual tablets taken together at all tested dose strengths.

  2. [Effect of Food Thickeners on the Disintegration, Dissolution, and Drug Activity of Rapid Oral-disintegrating Tablets].

    PubMed

    Tomita, Takashi; Kohda, Yukinao; Kudo, Kenzo

    2018-01-01

     For patients with dysphagia in medical facilities and nursing homes, food thickeners are routinely used to aid the ingestion of medicines such as tablets. However, some types of thickeners affect the disintegration and dissolution of tablets, such as rapidly-disintegrating magnesium oxide tablets and donepezil hydrochloride orally disintegrating tablets. Additionally, delayed disintegration and dissolution of tablets affect a drug's efficacy. As an example, with Voglibose orally disintegrating tablets, marked differences are observed in changes in glucose levels during glucose tolerance testing. When using food thickeners to aid tablet ingestion, it is therefore necessary to select a product that has little effect on drug disintegration, dissolution, and activity.

  3. Authentication of gold nanoparticle encoded pharmaceutical tablets using polarimetric signatures.

    PubMed

    Carnicer, Artur; Arteaga, Oriol; Suñé-Negre, Josep M; Javidi, Bahram

    2016-10-01

    The counterfeiting of pharmaceutical products represents concerns for both industry and the safety of the general public. Falsification produces losses to companies and poses health risks for patients. In order to detect fake pharmaceutical tablets, we propose producing film-coated tablets with gold nanoparticle encoding. These coated tablets contain unique polarimetric signatures. We present experiments to show that ellipsometric optical techniques, in combination with machine learning algorithms, can be used to distinguish genuine and fake samples. To the best of our knowledge, this is the first report using gold nanoparticles encoded with optical polarimetric classifiers to prevent the counterfeiting of pharmaceutical products.

  4. Chemoinformetrical evaluation of dissolution property of indomethacin tablets by near-infrared spectroscopy.

    PubMed

    Otsuka, Makoto; Tanabe, Hideaki; Osaki, Kazuo; Otsuka, Kuniko; Ozaki, Yukihiro

    2007-04-01

    The purpose of this study was to use near-infrared spectrometry (NIR) with chemoinformetrics to predict the change of dissolution properties in indomethacin (IMC) tablets during the manufacturing process. A comparative evaluation of the dissolution properties of the tablets was performed by the diffused reflectance (DRNIR) and transmittance (TNIR) NIR spectroscopic methods. Various kinds of IMC tablets (200 mg) were obtained from a powder (20 mg of IMC, 18 mg of microcrystalline cellulose, 160 mg of lactose, and 2 mg of magnesium stearate) under various compression pressures (60-398 MPa). Dissolution tests were performed in phosphate buffer, and the time required for 75% dissolution (T75) and mean dissolution time (MDT) were calculated. DRNIR and TNIR spectra were recorded, and the both NIR spectra used to establish a calibration model for predicting the dissolution properties by principal component regression analysis (PCR). The T75 and MDT increased as the compression pressure increased, since tablet porosity decreased with increasing pressure. Intensity of the DRNIR spectra of the compressed tablets decreased as the compression pressure increased. However, the intensity of TNIR spectra increased along with the pressure. The calibration models used to evaluate the dissolution properties of tablets were established by using PCR based on both DRNIR and TNIR spectra of the tablets. The multiple correlation coefficients of the relationship between the actual and predictive T75 by the DRNIR and TNIR methods were 0.831 and 0.962, respectively. It is possible to predict the dissolution properties of pharmaceutical preparations using both DRNIR and TNIR chemoinformetric methods. The TNIR method was more accurate for predictions of the dissolution behavior of tablets than the DRNIR method. (c) 2007 Wiley-Liss, Inc.

  5. Spatial Distribution of Trehalose Dihydrate Crystallization in Tablets by X-ray Diffractometry.

    PubMed

    Thakral, Naveen K; Yamada, Hiroyuki; Stephenson, Gregory A; Suryanarayanan, Raj

    2015-10-05

    Crystallization of trehalose dihydrate (C12H22O11·2H2O) was induced by storing tablets of amorphous anhydrous trehalose (C12H22O11) at 65% RH (RT). Our goal was to evaluate the advantages and limitations of two approaches of profiling spatial distribution of drug crystallization in tablets. The extent of crystallization, as a function of depth, was determined in tablets stored for different time-periods. The first approach was glancing angle X-ray diffractometry, where the penetration depth of X-rays was modulated by the incident angle. Based on the mass attenuation coefficient of the matrix, the depth of X-ray penetration was calculated as a function of incident angle, which in turn enabled us to "calculate" the extent of crystallization to different depths. In the second approach, the tablets were split into halves and the split surfaces were analyzed directly. Starting from the tablet surface and moving toward the midplane, XRD patterns were collected in 36 "regions", in increments of 0.05 mm. The results obtained by the two approaches were, in general, in good agreement. Additionally, the results obtained were validated by determining the "average" crystallization in the entire tablet by using synchrotron radiation in the transmission mode. The glancing angle method could detect crystallization up to ∼650 μm and had a "surface bias". Being a nondestructive technique, this method will permit repeated analyses of the same tablet at different time points, for example, during a stability study. However, split tablet analyses, while a "destructive" technique, provided comprehensive and unbiased depth profiling information.

  6. Stability of benzocaine formulated in commercial oral disintegrating tablet platforms.

    PubMed

    Köllmer, Melanie; Popescu, Carmen; Manda, Prashanth; Zhou, Leon; Gemeinhart, Richard A

    2013-12-01

    Pharmaceutical excipients contain reactive groups and impurities due to manufacturing processes that can cause decomposition of active drug compounds. The aim of this investigation was to determine if commercially available oral disintegrating tablet (ODT) platforms induce active pharmaceutical ingredient (API) degradation. Benzocaine was selected as the model API due to known degradation through ester and primary amino groups. Benzocaine was either compressed at a constant pressure, 20 kN, or at pressure necessary to produce a set hardness, i.e., where a series of tablets were produced at different compression forces until an average hardness of approximately 100 N was achieved. Tablets were then stored for 6 months under International Conference on Harmonization recommended conditions, 25°C and 60% relative humidity (RH), or under accelerated conditions, 40°C and 75% RH. Benzocaine degradation was monitored by liquid chromatography-mass spectrometry. Regardless of the ODT platform, no degradation of benzocaine was observed in tablets that were kept for 6 months at 25°C and 60% RH. After storage for 30 days under accelerated conditions, benzocaine degradation was observed in a single platform. Qualitative differences in ODT platform behavior were observed in physical appearance of the tablets after storage under different temperature and humidity conditions.

  7. Method of modelling the compaction behaviour of cylindrical pharmaceutical tablets.

    PubMed

    Ahmat, Norhayati; Ugail, Hassan; Castro, Gabriela González

    2011-02-28

    The mechanisms involved for compaction of pharmaceutical powders have become a crucial step in the development cycle for robust tablet design with required properties. Compressibility of pharmaceutical materials is measured by a force-displacement relationship which is commonly analysed using a well known method, the Heckel model. This model requires the true density and compacted powder mass value to determine the powder mean yield pressure. In this paper, we present a technique for shape modelling of pharmaceutical tablets based on the use of partial differential equations (PDEs). This work also presents an extended formulation of the PDE method to a higher dimensional space by increasing the number of parameters responsible for describing the surface in order to generate a solid tablet. Furthermore, the volume and the surface area of the parametric cylindrical tablet have been estimated numerically. Finally, the solution of the axisymmetric boundary value problem for a finite cylinder subject to a uniform axial load has been utilised in order to model the displacement components of a compressed PDE-based representation of a tablet. The Heckel plot obtained from the developed model shows that the model is capable of predicting the compaction behaviour of pharmaceutical materials since it fits the experimental data accurately. Copyright © 2010 Elsevier B.V. All rights reserved.

  8. Slide shows vs graphic tablet live drawing for anatomy teaching.

    PubMed

    Alsaid, B

    2016-12-01

    Blackboard drawing is the traditional and still widely learned method for anatomy teachers. However, for practical reasons, more and more lessons are done using slide shows. New digital learning tools are developed to create a more attractive teaching method. The objective of this study was to compare the use of graphic tablet live drawing versus slide shows. Sixty-five second-year students of the Faculty of Medicine participated in this study during their first semester of 2013-2014 academic year. The selected lecture dealt about neuroanatomy; two brain sections were taught: median sagittal and transverse. The sagittal section was presented via a slide show. The transverse section was taught using a graphics tablet using drawing software. Students were evaluated three times: before the lecture, immediately after the lecture and 8 weeks later. Means were compared using a t-test. Scores were significantly higher immediately after the lecture and 8 weeks later tests in comparing the transverse section (using the graphics tablet) versus the sagittal section (using PowerPoint ® ). Student satisfaction regarding the use of the tablet was high. The graphics tablet is a usable and efficient drawing tool in anatomy teaching. This tool requires a specific teacher training and preparation. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  9. Varying efficacy of superdisintegrants in orally disintegrating tablets among different manufacturers.

    PubMed

    Mittapalli, R K; Qhattal, H S Sha; Lockman, P R; Yamsani, M R

    2010-11-01

    The main objective of the present study was to develop an orally disintegrating tablet formulation of domperidone and to study the functionality differences of superdisintegrants each obtained from two different sources on the tablet properties. Domperidone tablets were formulated with different superdisintegrants by direct compression. The effect of the type of superdisintegrant, its concentration and source was studied by measuring the in-vitro disintegration time, wetting time, water absorption ratios, drug release by dissolution and in-vivo oral disintegration time. Tablets prepared with crospovidone had lower disintegration times than tablets prepared from sodium starchglycolate and croscarmellose sodium. Formulations prepared with Polyplasdone XL, Ac-Di-Sol, and Explotab (D series) were better than formulations prepared with superdisintegrants obtained from other sources (DL series) which had longer disintegration times and lower water uptake ratios. The in-vivo disintegration time of formulation D-106 containing polyplasdone XL was significantly lower than that of the marketed formulation Domel-MT. The results from this study suggest that disintegration of orally disintegrating tablets is dependent on the nature of superdisintegrant, concentration in the formulation and its source. Even though a superdisintegrant meets USP standards there can be a variance among manufacturers in terms of performance. This is not only limited to in-vitro studies but carries over to disintegration times in the human population.

  10. Optimization of formulation and processing of Moringa oleifera and spirulina complex tablets.

    PubMed

    Zheng, Yi; Zhu, Fan; Lin, Dan; Wu, Jun; Zhou, Yichao; Mark, Bohn

    2017-01-01

    Objective: To prepare a more comprehensive nutrition, more balanced proportion of natural nutritional supplement tablets with Moringa oleifera leaves and spirulina the two nutrients which have complementary natural food ingredients. Method: On the basis of research M. oleifera leaves with spirulina nutrient composition was determined on M. oleifera leaves and spirulina ratio of raw materials, and the choice of microcrystalline cellulose, sodium salt of caboxy methyl cellulose(CMC),magnesium stearate excipient, through single factor and orthogonal experiment, selecting the best formula tablets prepared by powder direct compression technology, for preparation of M. oleifera and spirulina complex tablets. Results: The best ratio of raw material for the M. oleifera leaves powder: spirulina powder was 7:3, the best raw materials for the tablet formulation was 88.5%, 8.0% microcrystalline cellulose, CMC 2.0%, stearin magnesium 1.5%, the optimum parameters for the raw material crushing 200-300 mesh particle size, moisture content of 7%, tableting pressure 40 kN. Conclusion: Through formulation and process optimization, we can prepare more comprehensive and balanced nutrition M. oleifera and spirulina complex tablets, its sheet-shaped appearance, piece weight variation, hardness, friability, disintegration and other indicators have reached the appropriate quality requirements.

  11. Coherent anti-Stokes Raman Scattering (CARS) Microscopy Visualizes Pharmaceutical Tablets During Dissolution

    PubMed Central

    Fussell, Andrew L.; Kleinebudde, Peter; Herek, Jennifer; Strachan, Clare J.; Offerhaus, Herman L.

    2014-01-01

    Traditional pharmaceutical dissolution tests determine the amount of drug dissolved over time by measuring drug content in the dissolution medium. This method provides little direct information about what is happening on the surface of the dissolving tablet. As the tablet surface composition and structure can change during dissolution, it is essential to monitor it during dissolution testing. In this work coherent anti-Stokes Raman scattering microscopy is used to image the surface of tablets during dissolution while UV absorption spectroscopy is simultaneously providing inline analysis of dissolved drug concentration for tablets containing a 50% mixture of theophylline anhydrate and ethyl cellulose. The measurements showed that in situ CARS microscopy is capable of imaging selectively theophylline in the presence of ethyl cellulose. Additionally, the theophylline anhydrate converted to theophylline monohydrate during dissolution, with needle-shaped crystals growing on the tablet surface during dissolution. The conversion of theophylline anhydrate to monohydrate, combined with reduced exposure of the drug to the flowing dissolution medium resulted in decreased dissolution rates. Our results show that in situ CARS microscopy combined with inline UV absorption spectroscopy is capable of monitoring pharmaceutical tablet dissolution and correlating surface changes with changes in dissolution rate. PMID:25045833

  12. The colorimetric analysis of anti-tuberculosis fixed-dose combination tablets and capsules.

    PubMed

    Ellard, G A

    1999-11-01

    The perceived need to demonstrate whether or not the actual amounts of rifampicin, isoniazid and pyrazinamide in fixed-dose combination tablets or capsules correspond to their stated drug contents. To adapt specific, robust and simple colorimetric methods that have been previously applied to measuring plasma and urinary rifampicin, isoniazid, pyrazinamide and ethambutol concentrations to estimate tablet and capsule drug contents. The methods were applied to the analysis of 14 commercially manufactured fixed-dose combinations: two capsule and three tablet formulations containing rifampicin and isoniazid; seven tablet formulations containing rifampicin, isoniazid and pyrazinamide; and two tablet formulations containing rifampicin, isoniazid, pyrazinamide and ethambutol. All the combined formulations contained near to their stated drug contents. Replicate analyses confirmed the excellent precision of the drug analyses. Such methods are not only rapid to perform but should be practical in many Third World situations with relatively modest laboratory facilities.

  13. Hexagonal boron nitride as a tablet lubricant and a comparison with conventional lubricants.

    PubMed

    Uğurlu, Timuçin; Turkoğlu, Murat

    2008-04-02

    The objective of this study was to investigate the lubrication properties of hexagonal boron nitride (HBN) as a new tablet lubricant and compare it with conventional lubricants such as magnesium stearate (MGST), stearic acid (STAC), and glyceryl behenate (COMP). Tablets were manufactured on an instrumented single-station tablet press to monitor lower punch ejection force (LPEF) containing varied lubricants in different ratio (0.5, 1, 2%). Tablet crushing strength, disintegration time and thickness were measured. Tensile strength of compacted tablets were measured by applying a diametrical load across the edge of tablets to determine mechanical strength. The deformation mechanism of tablets was studied during compression from the Heckel plots with or without lubricants. MGST was found to be the most effective lubricant based on LPEF-lubrication concentration profile and LPEF of HBN was found very close to that of MGST. HBN was better than both STAC and COMP. A good lubrication was obtained at 0.5% for MGST and HBN (189 and 195N, respectively). Where COMP and STAC showed 20 and 35% more LPEF compare to that of MGST (239 and 288N, respectively). Even at the concentration of 2% COMP and STAC did not decrease LPEF as much as 0.5% of MGST and HBN. Like all conventional lubricants the higher the concentration of HBN the lower the mechanical properties of tablets because of its hydrophobic character. However, this deterioration was not as pronounced as MGST. HBN had no significant effect on tablet properties. Based on the Heckel plots, it was observed that after the addition of 1% lubricant granules showed less plastic deformation.

  14. Multispectral UV imaging for fast and non-destructive quality control of chemical and physical tablet attributes.

    PubMed

    Klukkert, Marten; Wu, Jian X; Rantanen, Jukka; Carstensen, Jens M; Rades, Thomas; Leopold, Claudia S

    2016-07-30

    Monitoring of tablet quality attributes in direct vicinity of the production process requires analytical techniques that allow fast, non-destructive, and accurate tablet characterization. The overall objective of this study was to investigate the applicability of multispectral UV imaging as a reliable, rapid technique for estimation of the tablet API content and tablet hardness, as well as determination of tablet intactness and the tablet surface density profile. One of the aims was to establish an image analysis approach based on multivariate image analysis and pattern recognition to evaluate the potential of UV imaging for automatized quality control of tablets with respect to their intactness and surface density profile. Various tablets of different composition and different quality regarding their API content, radial tensile strength, intactness, and surface density profile were prepared using an eccentric as well as a rotary tablet press at compression pressures from 20MPa up to 410MPa. It was found, that UV imaging can provide both, relevant information on chemical and physical tablet attributes. The tablet API content and radial tensile strength could be estimated by UV imaging combined with partial least squares analysis. Furthermore, an image analysis routine was developed and successfully applied to the UV images that provided qualitative information on physical tablet surface properties such as intactness and surface density profiles, as well as quantitative information on variations in the surface density. In conclusion, this study demonstrates that UV imaging combined with image analysis is an effective and non-destructive method to determine chemical and physical quality attributes of tablets and is a promising approach for (near) real-time monitoring of the tablet compaction process and formulation optimization purposes. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. 21 CFR 520.310 - Caramiphen ethanedisulfonate and ammonium chloride tablets.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Caramiphen ethanedisulfonate and ammonium chloride... § 520.310 Caramiphen ethanedisulfonate and ammonium chloride tablets. (a) Specifications. Each tablet contains 10 milligrams of 5st caramiphen ethanedisulfonate and 80 milligrams of ammonium chloride.1 1 These...

  16. Colon Targeted Guar Gum Compression Coated Tablets of Flurbiprofen: Formulation, Development, and Pharmacokinetics

    PubMed Central

    Bontha, Vijaya Kumar

    2013-01-01

    The rationale of the present study is to formulate flurbiprofen colon targeted compression coated tablets using guar gum to improve the therapeutic efficacy by increasing drug levels in colon, and also to reduce the side effects in upper gastrointestinal tract. Direct compression method was used to prepare flurbiprofen core tablets, and they were compression coated with guar gum. Then the tablets were optimized with the support of in vitro dissolution studies, and further it was proved by pharmacokinetic studies. The optimized formulation (F4) showed almost complete drug release in the colon (99.86%) within 24 h without drug loss in the initial lag period of 5 h (only 6.84% drug release was observed during this period). The pharmacokinetic estimations proved the capability of guar gum compression coated tablets to achieve colon targeting. The C max of colon targeted tablets was 11956.15 ng/mL at T max of 10 h whereas it was 15677.52 ng/mL at 3 h in case of immediate release tablets. The area under the curve for the immediate release and compression coated tablets was 40385.78 and 78214.50 ng-h/mL and the mean resident time was 3.49 and 10.78 h, respectively. In conclusion, formulation of guar gum compression coated tablets was appropriate for colon targeting of flurbiprofen. PMID:24260738

  17. The Determination of Calcium in Dietary Supplement Tablets by Ion-Exchange.

    ERIC Educational Resources Information Center

    Dietz, Mark L.

    1986-01-01

    An experimental simple ion-exchange experiment in which the amount of calcium present in dietary supplement tablets has been developed is described and some typical student results for several brands of tablets are presented. (JN)

  18. Reading Rate and Comprehension for Text Presented on Tablet and Paper: Evidence from Arabic.

    PubMed

    Hermena, Ehab W; Sheen, Mercedes; AlJassmi, Maryam; AlFalasi, Khulood; AlMatroushi, Maha; Jordan, Timothy R

    2017-01-01

    The effectiveness of tablet computers to supplement or replace paper-based text in everyday life has yet to be fully revealed. Previous investigations comparing reading performance using tablets and paper have, however, reported inconsistent results. Furthermore, the interpretability of some previous findings is limited by lack of experimental control over variables like text display conditions. In the current study, we investigated reading performance for text presented on tablet and paper. Crucially, the levels of luminance and contrast were matched precisely across tablet and paper. The study used Arabic text which differs substantially from the languages used previously to investigate effects of tablet and paper on reading, thus offering a distinctive test of the influence of these two media on reading performance. The results suggest that when text display conditions are well-matched, there is no reliable difference in reading performance between the two media. Also, neither the order of medium (reading from tablet or paper first), nor familiarity with using a tablet significantly influence reading performance. These results call into question previous suggestions that reading from tablets is linked to poorer reading performance, and demonstrate the benefits of controlling text display conditions. These findings are of interest to reading scientists and educators.

  19. Reading Rate and Comprehension for Text Presented on Tablet and Paper: Evidence from Arabic

    PubMed Central

    Hermena, Ehab W.; Sheen, Mercedes; AlJassmi, Maryam; AlFalasi, Khulood; AlMatroushi, Maha; Jordan, Timothy R.

    2017-01-01

    The effectiveness of tablet computers to supplement or replace paper-based text in everyday life has yet to be fully revealed. Previous investigations comparing reading performance using tablets and paper have, however, reported inconsistent results. Furthermore, the interpretability of some previous findings is limited by lack of experimental control over variables like text display conditions. In the current study, we investigated reading performance for text presented on tablet and paper. Crucially, the levels of luminance and contrast were matched precisely across tablet and paper. The study used Arabic text which differs substantially from the languages used previously to investigate effects of tablet and paper on reading, thus offering a distinctive test of the influence of these two media on reading performance. The results suggest that when text display conditions are well-matched, there is no reliable difference in reading performance between the two media. Also, neither the order of medium (reading from tablet or paper first), nor familiarity with using a tablet significantly influence reading performance. These results call into question previous suggestions that reading from tablets is linked to poorer reading performance, and demonstrate the benefits of controlling text display conditions. These findings are of interest to reading scientists and educators. PMID:28270791

  20. Effect of a disintegration mechanism on wetting, water absorption, and disintegration time of orodispersible tablets.

    PubMed

    Pabari, Rm; Ramtoola, Z

    2012-07-01

    The aim of this study was to evaluate the influence of disintegration mechanism of various types of disintegrants on the absorption ratio (AR), wetting time (WT), and disintegration time (DT) of orodispersible tablets (ODTs). ODTs were prepared by direct compression using mannitol as filler and disintegrants selected from a range of swellable, osmotic, and porous disintegrants. Tablets formed were characterized for their water AR, WT, and DT. The porosity and mechanical strength of the tablets were also measured. Results show that the DT of formulated ODTs was directly related to the WT and was a function of the disintegration mechanism of the disintegrant used. The lowest WT and DT were observed for tablets formulated using the osmotic disintegrant sodium citrate and these tablets also showed the lowest AR and porosity. The wetting and disintegration of tablets containing the highly swellable disintegrant, sodium starch glycollate, was slowest despite their high water AR and high tablet porosity. Rapid wetting and disintegration of ODTs were therefore not necessarily related to the porosity of the tablets.

  1. Effect of a Disintegration Mechanism on Wetting, Water Absorption, and Disintegration Time of Orodispersible Tablets

    PubMed Central

    Pabari, RM; Ramtoola, Z

    2012-01-01

    The aim of this study was to evaluate the influence of disintegration mechanism of various types of disintegrants on the absorption ratio (AR), wetting time (WT), and disintegration time (DT) of orodispersible tablets (ODTs). ODTs were prepared by direct compression using mannitol as filler and disintegrants selected from a range of swellable, osmotic, and porous disintegrants. Tablets formed were characterized for their water AR, WT, and DT. The porosity and mechanical strength of the tablets were also measured. Results show that the DT of formulated ODTs was directly related to the WT and was a function of the disintegration mechanism of the disintegrant used. The lowest WT and DT were observed for tablets formulated using the osmotic disintegrant sodium citrate and these tablets also showed the lowest AR and porosity. The wetting and disintegration of tablets containing the highly swellable disintegrant, sodium starch glycollate, was slowest despite their high water AR and high tablet porosity. Rapid wetting and disintegration of ODTs were therefore not necessarily related to the porosity of the tablets. PMID:23112534

  2. A Simple and Effective Physical Characteristic Profiling Method for Methamphetamine Tablet Seized in China.

    PubMed

    Li, Tao; Hua, Zhendong; Meng, Xin; Liu, Cuimei

    2018-03-01

    Methamphetamine (MA) tablet production confers chemical and physical properties. This study developed a simple and effective physical characteristic profiling method for MA tablets with capital letter "WY" logos, which realized the discrimination between linked and unlinked seizures. Seventeen signature distances extracted from the "WY" logo were explored as factors for multivariate analysis and demonstrated to be effective to represent the features of tablets in the drug intelligence perspective. Receiver operating characteristic (ROC) curve was used to evaluate efficiency of different pretreatments and distance/correlation metrics, while "Standardization + Euclidean" and "Logarithm + Euclidean" algorithms outperformed the rest. Finally, hierarchical cluster analysis (HCA) was applied to the data set of 200 MA tablet seizures randomly selected from cases all around China in 2015, and 76% of them were classified into a group named after "WY-001." Moreover, the "WY-001" tablets occupied 51-80% tablet seizures from 2011 to 2015 in China, indicating the existence of a huge clandestine factory incessantly manufacturing MA tablets. © 2017 American Academy of Forensic Sciences.

  3. Novel mesalamine-loaded beads in tablets for delayed release of drug to the colon.

    PubMed

    Nguyen, Chien; Christensen, J Mark; Ayres, James W

    2012-01-01

    Novel 'beads-in-a-tablet' formulations (total weight ∼740-780 mg) have been prepared that meet USP 31 requirements for Delayed Release of mesalamine. Several methods are presented that overcome breakage of beads during tablet compaction were explored. Bead formulations comprise a combination of extrusion and spheronization to produce a relatively high drug load (80%), followed by coating (25%) with a colonic-targeted drug release polymer (polymethacrylates, Eudragit(®) S100), overcoated (3%) with hydroxypropyl methylcellulose (Opadry(®)) to improve bead binding and compactability, and using 20% coat of lactose/sodium starch glycolate (Explotab(®)) as binder/disintegrant/cushioning agent, thus allowing a sufficiently thick coating to be uniform and without being broken during tablet compaction. Then, the aforementioned beads were compressed into tablets at 1500 pounds of pressure containing 400 mg of mesalamine, and finally coating the compressed tablets with Surelease(®) (ethylcellulose):Opadry(®) = 1:0.5 ranging from 1.5-2.5% weight gain; the resulting tablets met USP 31 dissolution requirements for delayed release tablets.

  4. Laser Printing of PCL/Progesterone Tablets for Drug Delivery Applications in Hormone Cancer Therapy

    NASA Astrophysics Data System (ADS)

    Salmoria, G. V.; Klauss, P.; Kanis, L. A.

    2017-09-01

    In this study, polycaprolactone (PCL) and progesterone (PG) tablets were produced by selective laser sintering (SLS) using different particle sizes and laser energy. The sintered PCL/PG tablets presented uniform morphology, coalescence of particles and interconnected pores distributed in the polymeric matrix. The EDS analysis confirmed the presence of progesterone recrystallized on the surface of the porous PCL matrix. The crystallinity values for the PCL/PG tablets were lower than that for the pure PCL, suggesting the interaction of components at the molecular level. The PCL/PG tablets fabricated with small particles and high laser energy presented a higher value for the flexural modulus compared with the other specimens. The glass transition temperature (Tg) was -37 °C for the PCL/PG tablet with a high degree of sintering. The fatigue test showed that the PCL/PG blend tablets have high fatigue strength. The drug release mechanism of all tablets studied followed a zero-order kinetics, and drug release rates were dependent on sintering degree and, consequently, on matrix erosion, showing a potential application to controlled drug delivery in hormone cancer therapy.

  5. Toward predicting tensile strength of pharmaceutical tablets by ultrasound measurement in continuous manufacturing.

    PubMed

    Razavi, Sonia M; Callegari, Gerardo; Drazer, German; Cuitiño, Alberto M

    2016-06-30

    An ultrasound measurement system was employed as a non-destructive method to evaluate its reliability in predicting the tensile strength of tablets and investigate the benefits of incorporating it in a continuous line, manufacturing solid dosage forms. Tablets containing lactose, acetaminophen, and magnesium stearate were manufactured continuously and in batches. The effect of two processing parameters, compaction force and level of shear strain were examined. Young's modulus and tensile strength of tablets were obtained by ultrasound and diametrical mechanical testing, respectively. It was found that as the blend was exposed to increasing levels of shear strain, the speed of sound in the tablets decreased and the tablets became both softer and mechanically weaker. Moreover, the results indicate that two separate tablet material properties (e.g., relative density and Young's modulus) are necessary in order to predict tensile strength. A strategy for hardness prediction is proposed that uses the existing models for Young's modulus and tensile strength of porous materials. Ultrasound testing was found to be very sensitive in differentiating tablets with similar formulation but produced under different processing conditions (e.g., different level of shear strain), thus, providing a fast, and non-destructive method for hardness prediction that could be incorporated to a continuous manufacturing process. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Effect of drug particle size in ultrasound compacted tablets. Continuum percolation model approach.

    PubMed

    Millán, Mónica; Caraballo, Isidoro

    2006-03-09

    The main objective of this work is to study the influence of the drug particle size on the pharmaceutical availability of ultrasound compacted tablets. Inert matrix systems containing different drug particle sizes were prepared using both, an ultrasound-assisted press and a traditional eccentric machine. Potassium chloride was used as drug model and Eudragit RS-PM as matrix forming excipient. The excipient particle size was kept constant. The cross-sectional microphotographs of ultrasound tablets show the existence of a quasi-continuum medium. Keeping constant the drug load, US-tablets showed very similar release rates, whereas for traditional tablets, an increase in the particle size resulted in a clear decrease in the release rate. In these tablets, the excipient forms an almost continuum medium. In an infinite theoretical system of these characteristics, the size of the drug particles will not modify the percolation threshold. The percolation of the excipient in this system can be assimilated to a continuum percolation model. In accordance with the proposed model, a lower influence of the drug particle size on the drug release rate was obtained for the US-tablets in comparison with traditional tablets. This fact can be indicative of the similarity of the drug percolation thresholds in these systems.

  7. A Pilot Stability Study of Dehydroepiandrosterone Rapid-dissolving Tablets Prepared by Extemporaneous Compounding.

    PubMed

    Rush, Steven D; Vernak, Charlene; Zhao, Fang

    2017-01-01

    Dehydroepiandrosterone supplementation is used to treat a variety of conditions. Rapid-dissolving tablets are a relatively novel choice for compounded dehydroepiandrosterone dosage forms. While rapid-dissolving tablets offer ease of administration, there are uncertainties about the physical and chemical stability of the drug and dosage form during preparation and over long-term storage. This study was designed to evaluate the stability of dehydroepiandrosterone rapid-dissolving tablets just after preparation and over six months of storage. The Professional Compounding Centers of America rapid-dissolving tablet mold and base formula were used to prepare 10-mg strength dehydroepiandrosterone rapid-dissolving tablets. The formulation was heated at 100°C to 110°C for 30 minutes, released from the mold, and cooled at room temperature for 30 minutes. The resulting rapid-dissolving tablets were individually packaged in amber blister packs and stored in a stability chamber maintained at 25°C and 60% relative humidity. The stability samples were pulled at pre-determined time points for evaluation, which included visual inspection, tablet weight check, United States Pharmacopeia disintegration test, and stability-indicating high-performance liquid chromatography. The freshly prepared dehydroepiandrosterone rapiddissolving tablets exhibited satisfactory chemical and physical stability. Time 0 samples disintegrated within 40 seconds in water kept at 37°C. The high-performance liquid chromatographic results confirmed that the initial potency was 101.9% of label claim and that there was no chemical degradation from the heating procedure. Over six months of storage, there were no significant changes in visual appearance, physical integrity, or disintegration time for any of the stability samples. The high-performance liquid chromatographic results also indicated that dehydroepiandrosterone rapid-dissolving tablets retained >95% label claim with no detectable degradation

  8. A critical Examination of the Phenomenon of Bonding Area - Bonding Strength Interplay in Powder Tableting.

    PubMed

    Osei-Yeboah, Frederick; Chang, Shao-Yu; Sun, Changquan Calvin

    2016-05-01

    Although the bonding area (BA) and bonding strength (BS) interplay is used to explain complex tableting behaviors, it has never been experimentally proven. The purpose of this study is to unambiguously establish the distinct contributions of each by decoupling the contributions from BA and BS. To modulate BA, a Soluplus® powder was compressed into tablets at different temperatures and then broken following equilibration at 25°C. To modulate BS, tablets were equilibrated at different temperatures. To simultaneously modulate BA and BS, both powder compression and tablet breaking test were carried out at different temperatures. Lower tablet tensile strength is observed when the powder is compressed at a lower temperature but broken at 25°C. This is consistent with the increased resistance to polymer deformation at lower temperatures. When equilibrated at different temperatures, the tensile strength of tablets prepared under identical conditions increases with decreasing storage temperature, indicating that BS is higher at a lower temperature. When powder compression and tablet breaking are carried out at the same temperature, the profile with a maximum tensile strength at 4°C is observed due to the BA-BS interplay. By systematically varying temperature during tablet compression and breaking, we have experimentally demonstrated the phenomenon of BA-BS interplay in tableting.

  9. Aqueous Polymer Dispersion Coating Used for Osmotic Pump Tablets: Membrane Property Investigation and IVIVC Evaluation.

    PubMed

    Cheng, Lizhen; Gai, Xiumei; Wen, Haoyang; Liu, Dandan; Tang, Xin; Wang, Yanyan; Wang, Tuanjie; Pan, Weisan; Yang, Xinggang

    2018-01-01

    The objective of this study was to investigate the fundamental properties of propranolol hydrochloride osmotic pump tablets coated by aqueous polymer dispersion, simultaneously exploring the in vitro and in vivo correlation of the tablet. The physicochemical properties and parameters of aqueous polymer dispersion membranes (SEM, water uptake, and water vapor transmission coefficient) were investigated. In addition, the release behavior and the in vitro release and in vivo absorption profiles of the tablets coated by aqueous polymer dispersion were investigated by comparing with propranolol hydrochloride osmotic pump tablets coated by an organic solvent. Results showed that the similarity factor (f 2 ) between cellulose acetate-coated tablet and Eudragit-coated tablet was 78.1, and f 2 between cellulose acetate-coated tablet and Kollicoat-coated tablet was 77.6. The linear IVIVC of Eudragit-coated and Kollicoat-coated osmotic pump tablets was determined, which confirmed excellent correlation between the absorption in vivo and the drug release in vitro. Consequently, the membrane coated by aqueous polymer dispersion or organic solvent has similar in vitro release rates of controlled release. Also, compared with organic solvent coating, aqueous polymer dispersion has numerous advantages, such as reduced toxicity and no environmental damage. Therefore, the aqueous polymer dispersion technology has enormous potential as a replacement of organic solvent coating.

  10. Formulation and In Vitro, In Vivo Evaluation of Effervescent Floating Sustained-Release Imatinib Mesylate Tablet

    PubMed Central

    Kadivar, Ali; Kamalidehghan, Behnam; Javar, Hamid Akbari; Davoudi, Ehsan Taghizadeh; Zaharuddin, Nurul Dhania; Sabeti, Bahareh; Chung, Lip Yong; Noordin, Mohamed Ibrahim

    2015-01-01

    Introduction Imatinib mesylate is an antineoplastic agent which has high absorption in the upper part of the gastrointestinal tract (GIT). Conventional imatinib mesylate (Gleevec) tablets produce rapid and relatively high peak blood levels and requires frequent administration to keep the plasma drug level at an effective range. This might cause side effects, reduced effectiveness and poor therapeutic management. Therefore, floating sustained-release Imatinib tablets were developed to allow the tablets to be released in the upper part of the GIT and overcome the inadequacy of conventional tablets. Methodology Floating sustained-release Imatinib mesylate tablets were prepared using the wet granulation method. Tablets were formulated using Hydroxypropyl Methylcellulose (HPMC K4M), with Sodium alginate (SA) and Carbomer 934P (CP) as release-retarding polymers, sodium bicarbonate (NaHCO3) as the effervescent agent and lactose as a filler. Floating behavior, in vitro drug release, and swelling index studies were conducted. Initial and total drug release duration was compared with a commercial tablet (Gleevec) in 0.1 N HCl (pH 1.2) at 37 ± 0.5°C for 24 hours. Tablets were then evaluated for various physical parameters, including weight variation, thickness, hardness, friability, and drug content. Consequently, 6 months of physical stability studies and in vitro gastro-retentive studies were conducted. Results and Discussion Statistical data analysis revealed that tablets containing a composition of 14.67% w/w HPMC K4M, 10.67%, w/w Na alginate, 1.33%, w/w Carbomer 934P and 9.33%, w/w NaHCO3 produced the most favorable formulation to develop 24-hour sustained-release tablets with optimum floating behavior and satisfactory physicochemical characteristics. Furthermore, in vitro release study revealed that the formulated SR tablet had significantly lower Cmax and higher Tmax compared to the conventional tablet (Gleevec). Thus, formulated SR tablets preserved persistent

  11. Stability of Dihydroartemisinin-Piperaquine Tablet Halves During Prolonged Storage Under Tropical Conditions.

    PubMed

    Hodel, Eva Maria; Kaur, Harparkash; Terlouw, Dianne J

    2017-02-08

    Dihydroartemisinin-piperaquine (DP) is recommended for the treatment of uncomplicated malaria, used in efforts to contain artemisinin resistance, and increasingly considered for mass drug administration. Because of the narrow therapeutic dose range and available tablet strengths, the manufacturers and World Health Organization recommended regimens involve breaking tablets into halves to accurately dose children according to body weight. Use of tablet fractions in programmatic settings under tropical conditions requires a highly stable product; however, the stability of DP tablet fractions is unknown. We aged full and half DP (Eurartesim ® ) tablets in a stability chamber at 30°C and 70% humidity level. The active pharmaceutical ingredients dihydroartemisinin and piperaquine remained at ≥ 95% over the 3 months' period of ageing in light and darkness. These findings are reassuring for DP, but highlight the need to assess drug stability under real-life settings during the drug development process, particularly for key drugs of global disease control programs. © The American Society of Tropical Medicine and Hygiene.

  12. Learning, Tablet, Culture-Coherence?

    ERIC Educational Resources Information Center

    Norqvist, Lars

    2016-01-01

    This paper presents understandings of learning in schools where Internet-enabled Information and Communication Technologies (ICTs) are taken for granted. The context is a full-scale 1:1 tablet project in Danish municipality schools where this study bring forward expressions of learning from one class (12-13 year old children) in order to offer…

  13. A randomised trial of glucose tablets to aid smoking cessation.

    PubMed

    West, Robert; May, Sylvia; McEwen, Andy; McRobbie, Hayden; Hajek, Peter; Vangeli, Eleni

    2010-01-01

    Oral glucose has been found to decrease tobacco craving among abstaining smokers. One study has demonstrated an effect of glucose on short-term abstinence. There is a need to examine any long-term benefit of glucose on abstinence. To assess whether glucose tablets improve 6-month continuous abstinence rates compared with low-calorie placebo tablets. Smokers attempting to stop (n = 928) were randomised to receive glucose or sorbitol (placebo) in a double-blind placebo-controlled trial. All participants received group-based psychological support, and approximately half (n = 474) received nicotine replacement therapy (NRT), buproprion, or both. Smokers were seen weekly for 5 weeks and used tablets ad libitum, with a recommended minimum of 12 per day. Participants were recruited through general practitioner referral, word of mouth, and advertising. The participants were 38% male, smoked an average of 23.5 cigarettes per day, and had a mean age of 44 years. There were no significant pretreatment differences between groups. The primary outcome measure was continuous, CO-verified abstinence from the target quit date for 6 months. No significant effect of glucose tablets on abstinence was found (14.6% vs 13.4% abstinence in the glucose and placebo groups, respectively). However, there was a significant interaction with a glucose effect observed in smokers also receiving other medication (18.2% vs 12.6%, p < 0.05) but not otherwise (10.7% vs 14.3% ; p < 0.05 for the interaction). No significant effect of glucose tablets over and above sweet tasting tablets could be detected overall, but the possibility of an effect as an adjunct to NRT or bupropion merits further investigation.

  14. Adolescents' struggles with swallowing tablets: barriers, strategies and learning.

    PubMed

    Hansen, Dana Lee; Tulinius, Ditte; Hansen, Ebba Holme

    2008-01-01

    To explore adolescents' struggles with taking oral medications. Copenhagen, Denmark. Semi-structured qualitative interviews were conducted with 89 adolescents (33 boys, 56 girls) between the ages of 11 and 20. Adolescents were recruited through four public schools. To identify struggles with taking oral medication, interview transcripts were systematically searched for statements including the terms swallow, chew, crush and eat. Thematic analysis of the identified statements was carried out to reveal dominant themes in the adolescents' accounts. Over one-third of the adolescents spontaneously provided accounts of the difficulties they experienced with taking oral medications, especially with swallowing tablets. Three themes were dominant in their narratives: barriers, strategies and learning. Barriers experienced by the adolescents involved the medications' properties, e.g. taste. Adolescents developed strategies to overcome these barriers, e.g. crushing tablets. Via a process of learning-by-doing and the acquisition of increased experience and autonomy, many adolescents mastered the skill of swallowing tablets. Many adolescents experienced barriers in their attempts to swallow tablets. They developed various strategies to overcome these barriers and gradually mastered taking medicines in a learning-by-doing process.

  15. MedlinePlus® Everywhere: Access from Your Phone, Tablet or Desktop

    MedlinePlus

    ... gov/responsivefull.html MedlinePlus® Everywhere: Access from Your Phone, Tablet or Desktop To use the sharing features ... consistent user experience from a desktop, tablet, or phone. All users, regardless of how they access MedlinePlus, ...

  16. A Tablet Computer for Young Children? Exploring Its Viability for Early Childhood Education

    ERIC Educational Resources Information Center

    Couse, Leslie J.; Chen, Dora W.

    2010-01-01

    This study explored the viability of tablet computers in early education by investigating preschool children's ease in acclimating to tablet technology and its defectiveness in engaging them to draw. A total of 41 three- to six-year-old children were videotaped while they used the tablets. The study found significant differences in level of tablet…

  17. Perspectives of Students on Acceptance of Tablets and Self-Directed Learning with Technology

    ERIC Educational Resources Information Center

    Gokcearslan, Sahin

    2017-01-01

    Recent mobile learning technologies offer the opportunity for students to take charge of the learning process both inside and outside the classroom. One of these tools is the tablet PC (hereafter "tablet"). In parallel with increased access to e-content, the role of tablets in learning has recently begun to be examined. This study aims…

  18. Modeling the motion and orientation of various pharmaceutical tablet shapes in a film coating pan using DEM.

    PubMed

    Ketterhagen, William R

    2011-05-16

    Film coating uniformity is an important quality attribute of pharmaceutical tablets. Large variability in coating thickness can limit process efficiency or cause significant variation in the amount or delivery rate of the active pharmaceutical ingredient to the patient. In this work, the discrete element method (DEM) is used to computationally model the motion and orientation of several novel pharmaceutical tablet shapes in a film coating pan in order to predict coating uniformity. The model predictions are first confirmed with experimental data obtained from an equivalent film coating pan using a machine vision system. The model is then applied to predict coating uniformity for various tablet shapes, pan speeds, and pan loadings. The relative effects of these parameters on both inter- and intra-tablet film coating uniformity are assessed. The DEM results show intra-tablet coating uniformity is strongly influenced by tablet shape, and the extent of this can be predicted by a measure of the tablet shape. The tablet shape is shown to have little effect on the mixing of tablets, and thus, the inter-tablet coating uniformity. The pan rotation speed and pan loading are shown to have a small effect on intra-tablet coating uniformity but a more significant impact on inter-tablet uniformity. These results demonstrate the usefulness of modeling in guiding drug product development decisions such as selection of tablet shape and process operating conditions. Copyright © 2011 Elsevier B.V. All rights reserved.

  19. Disintegration of highly soluble immediate release tablets: a surrogate for dissolution.

    PubMed

    Gupta, Abhay; Hunt, Robert L; Shah, Rakhi B; Sayeed, Vilayat A; Khan, Mansoor A

    2009-01-01

    The purpose of the work was to investigate correlation between disintegration and dissolution for immediate release tablets containing a high solubility drug and to identify formulations where disintegration test, instead of the dissolution test, may be used as the acceptance criteria based on International Conference on Harmonization Q6A guidelines. A statistical design of experiments was used to study the effect of filler, binder, disintegrating agent, and tablet hardness on the disintegration and dissolution of verapamil hydrochloride tablets. All formulation variables, i.e., filler, binder, and disintegrating agent, were found to influence tablet dissolution and disintegration, with the filler and disintegrating agent exerting the most significant influence. Slower dissolution was observed with increasing disintegration time when either the filler or the disintegrating agent was kept constant. However, no direct corelationship was observed between the disintegration and dissolution across all formulations due to the interactions between different formulation components. Although all tablets containing sodium carboxymethyl cellulose as the disintegrating agent, disintegrated in less than 3 min, half of them failed to meet the US Pharmacopeia 30 dissolution criteria for the verapamil hydrochloride tablets highlighting the dependence of dissolution process on the formulation components other than the disintegrating agent. The results identified only one formulation as suitable for using the disintegration test, instead of the dissolution test, as drug product acceptance criteria and highlight the need for systematic studies before using the disintegration test, instead of the dissolution test as the drug acceptance criteria.

  20. Development and Characterization of Novel Floating-Mucoadhesive Tablets Bearing Venlafaxine Hydrochloride.

    PubMed

    Misra, Raghvendra; Bhardwaj, Peeyush

    2016-01-01

    The present investigation is concerned about the development of floating bioadhesive drug delivery system of venlafaxine hydrochloride which after oral administration exhibits a unique combination of floating and bioadhesion to prolong gastric residence time and increase drug bioavailability within the stomach. The floating bioadhesive tablets were prepared by the wet granulation method using different ratios of hydroxypropyl methyl cellulose (HPMC K4MCR) and Carbopol 934PNF as polymers. Sodium bicarbonate (NaHCO3) and citric acid were used as gas (CO2) generating agents. Tablets were characterized for floating properties, in vitro drug release, detachment force, and swelling index. The concentration of hydroxypropyl methyl cellulose and Carbopol 934PNF significantly affects the in vitro drug release, floating properties, detachment force, and swelling properties of the tablets. The optimized formulation showed the floating lag time 72 ± 2.49 seconds and duration of floating 24.50 ± 0.74 hr. The in vitro release studies and floating behavior were studied in simulated gastric fluid (SGF) at pH 1.2. Different drug release kinetics models were also applied. The in vitro drug release from tablets was sufficiently sustained (more than 18 hr) and the Fickian transports of the drug from the tablets were confirmed. The radiological evidence suggests that the tablets remained buoyant and altered position in the stomach of albino rabbit and mean gastric residence time was prolonged (more than > 6 hr).

  1. Tablet Computers on Trial: A Transformative Force in Education?

    ERIC Educational Resources Information Center

    Kjartansdóttir, Skúlína Hlíf; Jakobsdóttir, Sólveig

    2013-01-01

    In this paper we present the results of an evaluation study of a development project for the introduction and use of tablet computers (iPads) at the lower secondary level in Nordlinga school, a compulsory school in Reykjavík. In the study, we assess the impact of the use of tablet computers on instruction and students' learning in grades 9 to 10,…

  2. Properties of hot-melt extruded theophylline tablets containing poly(vinyl acetate).

    PubMed

    Zhang, F; McGinity, J W

    2000-09-01

    The objectives of this study were to investigate the properties of poly(vinyl acetate) (PVAc) as a retardant polymer and to study the drug release mechanism of theophylline from matrix tablets prepared by hot-melt extrusion. A physical mixture of drug, polymer, and drug release modifiers was fed into the equipment and heated inside the barrel of the extruder. The cylindrical extrudates were either cut into tablets or ground into granules and compressed with other excipients into tablets. Due to the low glass transition temperature of the PVAc, the melt extrusion process was conducted at approximately 70 degrees C. Theophylline was used as the model drug in this study. Theophylline was present in the extrudate in its crystalline form and was released from the tablets by diffusion. The Higuchi diffusion model and percolation theories were applied to the dissolution data to explain the drug release properties of the matrix systems. The release rate was shown to be dependent on the granule size, drug particle size, and drug loading in the tablets. Water-soluble polymers were demonstrated to be efficient release rate modifiers for this system.

  3. Influence of rate of force application during compression on tablet capping.

    PubMed

    Sarkar, Srimanta; Ooi, Shing Ming; Liew, Celine Valeria; Heng, Paul Wan Sia

    2015-04-01

    Root cause and possible processing remediation of tablet capping were investigated using a specially designed tablet press with an air compensator installed above the precompression roll to limit compression force and allow extended dwell time in the precompression event. Using acetaminophen-starch (77.9:22.1) as a model formulation, tablets were prepared by various combinations of precompression and main compression forces, set precompression thickness, and turret speed. The rate of force application (RFA) was the main factor contributing to the tablet mechanical strength and capping. When target force above the force required for strong interparticulate bond formation, the resultant high RFA contributed to more pronounced air entrapment, uneven force distribution, and consequently, stratified densification in compact together with high viscoelastic recovery. These factors collectively had contributed to the tablet capping. As extended dwell time assisted particle rearrangement and air escape, a denser and more homogenous packing in the die could be achieved. This occurred during the extended dwell time when a low precompression force was applied, followed by application of main compression force for strong interparticulate bond formation that was the most beneficial option to solve capping problem. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  4. Determining the coating thickness of tablets by chiseling and image analysis.

    PubMed

    Sasić, Slobodan

    2010-09-15

    Several tablets are chiseled and imaged in order to determine the variation in the coating thickness with the addition of the coating material (weight-gain). Chiseling is carried out with an ultrasonic chisel. The chiseled tablets are imaged in full and these images are exported into programming language Matlab in order to numerically analyze all the pixels along one side of the tablet. The coating thickness is statistically assessed at four cutting depths for three tablets obtained from four weight-gain experiments, a total of 48 images. The coating layer is clearly visible and determinable in the 'white-light' images even for the smallest weight gain of 1% but with sizeable errors due to the diffused boundaries between the coating and the core on one, and the coating and the background on the other side. Addition of the coating material clearly increases the coating thickness which is found to be somewhat higher at the top of the tablets than at the edges. Two approaches for assessment of the coating thickness are tested and are found to be in a very good agreement except for the thinnest coating layer. Copyright 2010 Elsevier B.V. All rights reserved.

  5. Formulation and Characterization of Oral Mucoadhesive Chlorhexidine Tablets Using Cordia myxa Mucilage.

    PubMed

    Moghimipour, Eskandar; Aghel, Nasrin; Adelpour, Akram

    2012-01-01

    The dilution and rapid elimination of topically applied drugs due to the flushing action of saliva is a major difficulty in the effort to eradicate infections of oral cavity. Utilization a proper delivery system for incorporation of drugs has a major impact on drug delivery and such a system should be formulated for prolonged drug retention in oral cavity. The aim of the present study was the use of mucilage of Cordia myxa as a mucoadhesive material in production of chlorhexidine buccal tablets and its substitution for synthetic polymers such as HPMC. The influence of mucilage concentration on the physicochemical responses (hardness, friability, disintegration time, dissolution, swelling, and muco-adhesiveness strength) was studied and swelling of mucilage and HPMC were compared. The evaluated responses included pharmacopoeial characteristics of tablets, the force needed to separate tablets from mucosa, and the amount of water absorbed by tablets. In comparison to HPMC, the rise of mucilage concentration in the formulations increased disintegration time, drug dissolution rate, and reduced MDT. Also, compared to 30% HPMC, muco-adhesiveness strength of buccal tablets containing 20% mucilage was significantly higher. It can be concluded that the presence of Cordia myxa powdered mucilage may significantly affect the tablet characteristics, and increasing in muco-adhesiveness may be achieved by using 20% w/w mucilage.

  6. Voltammetric Studies of Zomepirac Sodium and Its Determination in Tablets by Differential-Pulse Polarography.

    DTIC Science & Technology

    1984-01-06

    min in order to promote disintegration of the tablets . The remaining larger lumps of tablet mass were crushed with a glass rod and the mixture stirred...D-A136 982 VOLTAMMETRIC STUDIES OF ZOMEPIRAC SODIUM AND ITS i/i DETERMINATION IN TABLETS .. U) UTAH UNIV SALT LAKE CITY DEPT OF CHEMISTRY L G CHATTEN...TYPE OF REPORT &PEMOCVE Voltaninetric Studies of Zomepirac Sodium and its Dete~rmrination in Tablets by Differential-Pulse ,Technical Reportf 24 Pol

  7. Using tablet technology in operational radiation safety applications.

    PubMed

    Phillips, Andrew; Linsley, Mark; Houser, Mike

    2013-11-01

    Tablet computers have become a mainstream product in today's personal, educational, and business worlds. These tablets offer computing power, storage, and a wide range of available products to meet nearly every user need. To take advantage of this new computing technology, a system was developed for the Apple iPad (Apple Inc. 1 Infinite Loop Cupertino, CA 95014) to perform health and safety inspections in the field using editable PDFs and saving them to a database while keeping the process easy and paperless.

  8. Formulation and development of tablets based on Ludipress and scale-up from laboratory to production scale.

    PubMed

    Heinz, R; Wolf, H; Schuchmann, H; End, L; Kolter, K

    2000-05-01

    In spite of the wealth of experience available in the pharmaceutical industry, tablet formulations are still largely developed on an empirical basis, and the scale-up from laboratory to production is a time-consuming and costly process. Using Ludipress greatly simplifies formulation development and the manufacturing process because only the active ingredient Ludipress and a lubricant need to be mixed briefly before being compressed into tablets. The studies described here were designed to investigate the scale-up of Ludipress-based formulations from laboratory to production scale, and to predict changes in tablet properties due to changes in format, compaction pressure, and the use of different tablet presses. It was found that the tensile strength of tablets made of Ludipress increased linearly with compaction pressures up to 300 MPa. It was also independent of the geometry of the tablets (diameter, thickness, shape). It is therefore possible to give an equation with which the compaction pressure required to achieve a given hardness can be calculated for a given tablet form. The equation has to be modified slightly to convert from a single-punch press to a rotary tableting machine. Tablets produced in the rotary machine at the same pressure have a slightly higher tensile strength. The rate of increase in pressure, and therefore the throughput, has no effect on the tensile strength of Ludipress tablets. It is thought that a certain minimum dwell time is responsible for this difference. The production of tablets based on Ludipress can be scaled up from one rotary press to another without problem if the powder mixtures are prepared with the same mixing energy. The tensile strength curve determined for tablets made with Ludipress alone can also be applied to tablets with a small quantity (< 10%) of an active ingredient.

  9. Older Adults Perceptions of Technology and Barriers to Interacting with Tablet Computers: A Focus Group Study.

    PubMed

    Vaportzis, Eleftheria; Clausen, Maria Giatsi; Gow, Alan J

    2017-10-04

    New technologies provide opportunities for the delivery of broad, flexible interventions with older adults. Focus groups were conducted to: (1) understand older adults' familiarity with, and barriers to, interacting with new technologies and tablets; and (2) utilize user-engagement in refining an intervention protocol. Eighteen older adults (65-76 years old; 83.3% female) who were novice tablet users participated in discussions about their perceptions of and barriers to interacting with tablets. We conducted three separate focus groups and used a generic qualitative design applying thematic analysis to analyse the data. The focus groups explored attitudes toward tablets and technology in general. We also explored the perceived advantages and disadvantages of using tablets, familiarity with, and barriers to interacting with tablets. In two of the focus groups, participants had previous computing experience (e.g., desktop), while in the other, participants had no previous computing experience. None of the participants had any previous experience with tablet computers. The themes that emerged were related to barriers (i.e., lack of instructions and guidance, lack of knowledge and confidence, health-related barriers, cost); disadvantages and concerns (i.e., too much and too complex technology, feelings of inadequacy, and comparison with younger generations, lack of social interaction and communication, negative features of tablets); advantages (i.e., positive features of tablets, accessing information, willingness to adopt technology); and skepticism about using tablets and technology in general. After brief exposure to tablets, participants emphasized the likelihood of using a tablet in the future. Our findings suggest that most of our participants were eager to adopt new technology and willing to learn using a tablet. However, they voiced apprehension about lack of, or lack of clarity in, instructions and support. Understanding older adults' perceptions of technology

  10. Latent structure analysis in the pharmaceutical process of tablets prepared by wet granulation.

    PubMed

    Uehara, Naoto; Hayashi, Yoshihiro; Mochida, Hiroshi; Otoguro, Saori; Onuki, Yoshinori; Obata, Yasuko; Takayama, Kozo

    2016-01-01

    Granule characteristics are some of the important intermediate qualities that determine tablet properties. However, the relationships between granule and tablet characteristics are poorly understood. The aim of this study was to elucidate relationships among formulation factors, granule characteristics, and tablet properties using a non-linear response surface method (RSM) incorporating a thin-plate spline interpolation (RSM-S) and a Bayesian network (BN). Tablets containing lactose (Lac), cornstarch (CS), and microcrystalline cellulose (MCC) were prepared by wet granulation. Ten formulations were prepared by an extreme vertices design. The angle of repose (Y 1 ), compressibility (Y 2 ), cohesion force (Y 3 ), internal friction angle (Y 4 ), and mean particle size (Y 5 ) were measured as granule characteristics. Tensile strength (TS) and disintegration time (DT) were measured as tablet properties. RSM-S results showed that TS increased with increasing amounts of MCC and Lac. DT decreased with increasing amounts of MCC and CS. The optimal BN models were predicted using four evaluation indices -Y 3 was shown to be the most important factor for TS, whereas Y 2 , Y 3 , and Y 4 were relatively important for predicting DT. Moreover, tablets with excellent tablet properties (i.e. high TS and low DT) were produced by relatively high Y 1 , low Y 2 , high Y 3 , high Y 4 , and middle Y 5 values, and resulted from the middle of MCC, middle-to-low CS, low Lac, and middle-to-low magnesium stearate (Mg-St) amounts. The RSM-S and BN techniques are useful for revealing complex relationships among formulation factors, granule characteristics, and tablet properties.

  11. Analysis of illicit ecstasy tablets: implications for clinical management in the accident and emergency department.

    PubMed Central

    Sherlock, K; Wolff, K; Hay, A W; Conner, M

    1999-01-01

    OBJECTIVE: To examine the composition of illicitly manufactured "ecstasy" tablets sold on the UK drugs market. METHODS: Analysis by gas chromatography of 25 illicit ecstasy tablets handed in under amnesty to Leeds Addiction Unit. RESULTS: Illicitly manufactured ecstasy tablets contain a range of ingredients, of widely differing concentrations, and even tablets with the same brand name have variable concentrations of active ingredients. Concentrations of 3,4-methylenedioxymethamphetamine (MDMA) more popularly known as ecstasy, varied 70-fold between tablets. Nine tablets contained neither MDMA nor related analogues. CONCLUSIONS: These results have implications for emergency workers attending to those who have become casualties of the drug ecstasy. Those claiming to have ingested ecstasy may actually have taken other agents that require different clinical management. PMID:10353046

  12. Suppressed Release of Clarithromycin from Tablets by Crystalline Phase Transition of Metastable Polymorph Form I.

    PubMed

    Fujiki, Sadahiro; Watanabe, Narumi; Iwao, Yasunori; Noguchi, Shuji; Mizoguchi, Midori; Iwamura, Takeru; Itai, Shigeru

    2015-08-01

    The pharmaceutical properties of clarithromycin (CAM) tablets containing the metastable form I of crystalline CAM were investigated. Although the dissolution rate of form I was higher than that of stable form II, the release of CAM from form I tablet was delayed. Disintegration test and liquid penetration test showed that the disintegration of the tablet delayed because of the slow penetration of an external solution into form I tablet. Investigation by scanning electron microscopy revealed that the surface of form I tablet was covered with fine needle-shaped crystals following an exposure to the external solution. These crystals were identified as form IV crystals by powder X-ray diffraction. The phenomenon that CAM releases from tablet was inhibited by fine crystals spontaneously formed on the tablet surface could be applied to the design of sustained-release formulation systems with high CAM contents by minimizing the amount of functional excipients. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  13. Formulation and Evaluation of Fast-Disintegrating Sublingual Tablets of Atropine Sulfate: the Effect of Tablet Dimensions and Drug Load on Tablet Characteristics.

    PubMed

    Aodah, Alhussain; Bafail, Rawan S; Rawas-Qalaji, Mutasem

    2017-07-01

    In this study, we formulated and evaluated the effects of tablet dimensions and drug load on the characteristics of atropine sulfate (AS) fast-disintegrating sublingual tablets (FDSTs). We aim to develop AS FDSTs as an alternative non-invasive and portable dosage form for the emergency treatment of organophosphate (OP) toxicity. AS autoinjector, AtroPen®, is the only self-administered dosage form available as an antidote for-out-of-hospital emergency use, but it is associated with several limitations and drawbacks. Seven FDST formulations of two tablet sizes, 150 mg (A) and 50 mg (B), and of several AS loads, 0 mg (A1, B1), 2 mg (A2, B2), 4 mg (B3), and 8 mg (B4a, B4b), were formulated and manufactured by direct compression. AS FDST characteristics were evaluated using USP and non-USP tests. Results were statistically compared at p < 0.05. All FDSTs passed the USP content uniformity and friability tests, disintegrated and released AS in ≤30 and 60 s. B1 and B2 were significantly harder than A1 and A2. Water uptake of A1 was significantly the highest. However, B1 and B2 had shorter disintegration and wetting times and higher amounts of AS dissolved than did A1 and A2 (p < 0.05). Increasing AS negatively affected FDST tensile strength (p < 0.05 for B4a) and water uptake (p < 0.05 for B3, B4a and B4b), however, without affecting AS dissolution. Formulation of AS up to 16% into smaller FDSTs was successful. Smaller FDSTs were harder and disintegrated more quickly. These AS FDSTS have the potential for further in vivo testing to evaluate their OP antidote potential.

  14. Characterization of the coating and tablet core roughness by means of 3D optical coherence tomography.

    PubMed

    Markl, Daniel; Wahl, Patrick; Pichler, Heinz; Sacher, Stephan; Khinast, Johannes G

    2018-01-30

    This study demonstrates the use of optical coherence tomography (OCT) to simultaneously characterize the roughness of the tablet core and coating of pharmaceutical tablets. OCT is a high resolution non-destructive and contactless imaging methodology to characterize structural properties of solid dosage forms. Besides measuring the coating thickness, it also facilitates the analysis of the tablet core and coating roughness. An automated data evaluation algorithm extracts information about coating thickness, as well as tablet core and coating roughness. Samples removed periodically from a pan coating process were investigated, on the basis of thickness and profile maps of the tablet core and coating computed from about 480,000 depth measurements (i.e., 3D data) per sample. This data enables the calculation of the root mean square deviation, the skewness and the kurtosis of the assessed profiles. Analyzing these roughness parameters revealed that, for the given coating formulation, small valleys in the tablet core are filled with coating, whereas coarse features of the tablet core are still visible on the final film-coated tablet. Moreover, the impact of the tablet core roughness on the coating thickness is analyzed by correlating the tablet core profile and the coating thickness map. The presented measurement method and processing could be in the future transferred to in-line OCT measurements, to investigate core and coating roughness during the production of film-coated tablets. Copyright © 2017. Published by Elsevier B.V.

  15. Logistic growth for the Nuzi cuneiform tablets: Analyzing family networks in ancient Mesopotamia

    NASA Astrophysics Data System (ADS)

    Ueda, Sumie; Makino, Kumi; Itoh, Yoshiaki; Tsuchiya, Takashi

    2015-03-01

    We reconstruct the published year of each cuneiform tablet of the Nuzi society in ancient Mesopotamia. The tablets are on land transaction, marriage, loan, slavery contracts, etc. The number of tablets seems to increase by logistic growth. It may show the dynamics of concentration of lands or other properties into few powerful families in a period of about sixty years and most of them are in about thirty years. We reconstruct family trees and social networks of Nuzi and estimate the published years of cuneiform tablets consistently with the trees and networks, formulating least squares problems with linear inequality constraints.

  16. Esophageal transit and in vivo disintegration of branded risedronate sodium tablets and two generic formulations of alendronic acid tablets: a single-center, single-blind, six-period crossover study in healthy female subjects.

    PubMed

    Perkins, Alan C; Blackshaw, P Elaine; Hay, Peter D; Lawes, Simon C; Atherton, Clare T; Dansereau, Richard J; Wagner, Leigh K; Schnell, Dan J; Spiller, Robin C

    2008-05-01

    Delayed esophageal transit or disintegration of oral bisphosphonate tablets before they enter the stomach may be of concern with respect to iatrogenic complications among patients receiving longterm treatment. Different formulations of generic bisphosphonate tablets meeting regulatory requirements may have substantial differences in pharmaceutical attributes from the branded product that may result in different characteristics during esophageal transit. The primary objective of this study was to evaluate and compare esophageal transit times and in vivo disintegration of 3 bisphosphonate formulations, one branded and the others generic, that are commercially available in Canada and the United Kingdom. This was a single-center, randomized, singleblind, 6-period crossover study in healthy postmenopausal women aged >50 years. Each subject received a single oral dose of a branded risedronate sodium 35-mg tablet and 2 generic formulations of alendronic acid 70-mg tablets (Novopharm Limited, Toronto, Canada, and Teva UK Limited, Morley, United Kingdom) in both the erect and semisupine (45 degrees ) positions. Although the products are labeled to be taken in the erect position, the semisupine position was included to simulate dosing in bedridden patients. Subjects took tablets with 30 mL of water in the morning after an overnight fast. The tablets were radiolabeled with technetium-99m ion-exchange resins to enable visualization and measurement of esophageal transit time and disintegration using a gamma camera. Dynamic scintigraphic images were obtained for a total of 10 minutes: 2 images per second for the first 30 seconds and 1 image every 15 seconds for 9.5 minutes. This was a mechanistic study and tolerability was not assessed. The study was conducted in 20 healthy white female subjects with a mean age of 62 years (range, 51-77 years). The effect of body position was statistically significant (P = 0.043), with the estimated hazard ratio (HR) of 0.74 indicating longer

  17. Bioavailability, pharmacokinetics, and safety of riociguat given as an oral suspension or crushed tablet with and without food

    PubMed Central

    Frey, Reiner; Becker, Corina; Unger, Sigrun; Wensing, Georg; Mück, Wolfgang

    2016-01-01

    Abstract Riociguat is approved for the treatment of pulmonary arterial hypertension and chronic thromboembolic pulmonary hypertension. Some patients have difficulty swallowing tablets; therefore, 2 randomized, nonblinded, crossover studies compared the relative bioavailability of riociguat oral suspensions and immediate-release (IR) tablet and of crushed-tablet preparations versus whole IR tablet. In study 1, 30 healthy subjects received 5 single riociguat doses: 0.3 and 2.4 mg (0.15 mg/mL suspensions), 0.15 mg (0.03 mg/mL), and 1.0 mg (whole IR tablet) under fasted conditions and 2.4 mg (0.15 mg/mL) after a high-fat, high-calorie American-style breakfast. In study 2, 25 healthy men received 4 single 2.5-mg doses: whole IR tablet and crushed IR tablet suspended in applesauce and water, respectively, under fasted conditions, and whole IR tablet after a continental breakfast. In study 1, dose-normalized pharmacokinetics of riociguat oral suspensions and 1.0-mg whole IR tablet were similar in fasted conditions; 90% confidence intervals for riociguat area under the curve (AUC) to dose and mean maximum concentration (Cmax) to dose were within bioequivalence criteria. After food, dose-normalized AUC and Cmax decreased by 15% and 38%, respectively. In study 2, riociguat exposure was similar for all preparations; AUC ratios for crushed-IR-tablet preparations to whole IR tablet were within bioequivalence criteria. The Cmax increased by 17% for crushed IR tablet in water versus whole IR tablet. Food intake decreased Cmax of the whole tablet by 16%, with unaltered AUC versus fasted conditions. Riociguat bioavailability was similar between the oral suspensions and the whole IR tablet; exposure was similar between whole IR tablet and crushed-IR-tablet preparations. Minor food effects were observed. Results suggest that riociguat formulations are interchangeable. PMID:27162630

  18. Bioavailability, pharmacokinetics, and safety of riociguat given as an oral suspension or crushed tablet with and without food.

    PubMed

    Saleh, Soundos; Frey, Reiner; Becker, Corina; Unger, Sigrun; Wensing, Georg; Mück, Wolfgang

    2016-03-01

    Riociguat is approved for the treatment of pulmonary arterial hypertension and chronic thromboembolic pulmonary hypertension. Some patients have difficulty swallowing tablets; therefore, 2 randomized, nonblinded, crossover studies compared the relative bioavailability of riociguat oral suspensions and immediate-release (IR) tablet and of crushed-tablet preparations versus whole IR tablet. In study 1, 30 healthy subjects received 5 single riociguat doses: 0.3 and 2.4 mg (0.15 mg/mL suspensions), 0.15 mg (0.03 mg/mL), and 1.0 mg (whole IR tablet) under fasted conditions and 2.4 mg (0.15 mg/mL) after a high-fat, high-calorie American-style breakfast. In study 2, 25 healthy men received 4 single 2.5-mg doses: whole IR tablet and crushed IR tablet suspended in applesauce and water, respectively, under fasted conditions, and whole IR tablet after a continental breakfast. In study 1, dose-normalized pharmacokinetics of riociguat oral suspensions and 1.0-mg whole IR tablet were similar in fasted conditions; 90% confidence intervals for riociguat area under the curve (AUC) to dose and mean maximum concentration (C max) to dose were within bioequivalence criteria. After food, dose-normalized AUC and C max decreased by 15% and 38%, respectively. In study 2, riociguat exposure was similar for all preparations; AUC ratios for crushed-IR-tablet preparations to whole IR tablet were within bioequivalence criteria. The C max increased by 17% for crushed IR tablet in water versus whole IR tablet. Food intake decreased C max of the whole tablet by 16%, with unaltered AUC versus fasted conditions. Riociguat bioavailability was similar between the oral suspensions and the whole IR tablet; exposure was similar between whole IR tablet and crushed-IR-tablet preparations. Minor food effects were observed. Results suggest that riociguat formulations are interchangeable.

  19. Pharmaceutical and pharmacokinetic characterization of a novel sublingual buprenorphine/naloxone tablet formulation in healthy volunteers.

    PubMed

    Fischer, Andreas; Jönsson, Martin; Hjelmström, Peter

    2015-01-01

    Bitter taste, as well as dissolve time, presents a significant challenge for the acceptability of formulations for oral transmucosal drug delivery. To characterize a novel sublingual tablet formulation of buprenorphine/naloxone with regards to pharmacokinetics, dissolve time and formulation acceptability. Dry mixing techniques were employed to produce a small and fast dissolving buprenorphine/naloxone sublingual tablet formulation, OX219 (Zubsolv®), using sucralose and menthol as sweetener and flavor to mask the bitter taste of the active ingredients. Two cross-over studies were performed in healthy volunteers to evaluate pharmacokinetics, dissolve time and acceptability of OX219 5.7/1.4 mg tablets compared to the commercially available buprenorphine/naloxone formulations Suboxone® tablets and films (8/2 mg). Buprenorphine exposure was equivalent in OX219 and Suboxone tablets. Sublingual dissolve times were significantly shorter for OX219 than for Suboxone tablets and were similar to Suboxone films. The OX219 formulation received significantly higher subjective ratings for taste and overall acceptability than both Suboxone formulations. OX219 was preferred over Suboxone tablet and film formulations by 77.4% and 88.9% of subjects, respectively. A sublingual tablet formulation with an improved acceptability has been successfully developed.

  20. Assessment of intra-granular and extra-granular fracture in the development of tablet tensile strength.

    PubMed

    Mitra, Biplob; Hilden, Jon; Litster, James D

    2018-05-24

    When a tablet is compacted from deformable granules and then broken, the fracture plane may cleave granules in two (intra-granular fracture) or separate neighboring granules (extra-granular fracture). In this study, a novel method was developed to quantify the extent of intra- versus extra-granular fracture by compacting tablets from multi-colored ideal granules and evaluating fracture surfaces. The proportions of intra-granular and extra-granular fracture were quantified and modeled in light of a new metric, the deformation potential, Δ, reflecting the solid fraction increase as an initial granule bed is compressed into a final tablet. Results show that a measurable tablet strength is achieved at Δ > 0.18, but intra-granular fracture is not observed until Δ > 0.21. At very large Δ, tablets experience almost exclusively intra-granular fracture, yet the tablet tensile strength is considerably lower than that of a tablet compacted from raw powders versus pre-compacted granules. Thus, secondary compaction of granules appears to weaken the granule matrix, leading to reduced tablet tensile strength even in the presence of strong extra-granular bonding. Copyright © 2018. Published by Elsevier Inc.

  1. Mini-tablets versus pellets as promising multiparticulate modified release delivery systems for highly soluble drugs.

    PubMed

    Gaber, Dina M; Nafee, Noha; Abdallah, Osama Y

    2015-07-05

    Whether mini-tablets (tablets, diameters ≤6mm) belong to single- or multiple-unit dosage forms is still questionable. Accordingly, Pharmacopoeial evaluation procedures for mini-tablets are lacking. In this study, the aforementioned points were discussed. Moreover, their potential for oral controlled delivery was assessed. The antidepressant venlafaxine hydrochloride (Vx), a highly soluble drug undergoing first pass effect, low bioavailability and short half-life was selected as a challenging payload. In an attempt to weigh up mini-tablets versus pellets as multiparticulate carriers, Vx-loaded mini-tablets were compared to formulated pellets of the same composition and the innovator Effexor(®)XR pellets. Formulations were prepared using various polymer hydrogels in the core and ethyl cellulose film coating with increasing thickness. Mini-tablets (diameter 2mm) showed extended Vx release (<60%, 8h). Indeed, release profiles comparable to Effexor(®)XR pellets were obtained. Remarkably higher coating thickness was required for pellets to provide equivalent retardation. Ethyl cellulose in the core ensured faster release due to polymer migration to the surface and pore formation in the coat. mini-tablets showed higher stability to pellets upon storage. Industrially speaking, mini-tablets proved to be superior to pellets in terms of manufacturing, product quality and economical aspects. Results point out the urgent need for standardized evaluation procedures for mini-tablets. Copyright © 2015. Published by Elsevier B.V.

  2. Formulation design and optimization of mouth dissolve tablets of nimesulide using vacuum drying technique.

    PubMed

    Gohel, Mukesh; Patel, Madhabhai; Amin, Avani; Agrawal, Ruchi; Dave, Rikita; Bariya, Nehal

    2004-04-26

    The purpose of this research was to develop mouth dissolve tablets of nimesulide. Granules containing nimesulide, camphor, crospovidone, and lactose were prepared by wet granulation technique. Camphor was sublimed from the dried granules by exposure to vacuum. The porous granules were then compressed. Alternatively, tablets were first prepared and later exposed to vacuum. The tablets were evaluated for percentage friability, wetting time, and disintegration time. In the investigation, a 32 full factorial design was used to investigate the joint influence of 2 formulation variables: amount of camphor and crospovidone. The results of multiple linear regression analysis revealed that for obtaining a rapidly disintegrating dosage form, tablets should be prepared using an optimum concentration of camphor and a higher percentage of crospovidone. A contour plot is also presented to graphically represent the effect of the independent variables on the disintegration time and percentage friability. A checkpoint batch was also prepared to prove the validity of the evolved mathematical model. Sublimation of camphor from tablets resulted in superior tablets as compared with the tablets prepared from granules that were exposed to vacuum. The systematic formulation approach helped in understanding the effect of formulation processing variables.

  3. Dissolution of Intact, Divided and Crushed Circadin Tablets: Prolonged vs. Immediate Release of Melatonin.

    PubMed

    Chua, Hui Ming; Hauet Richer, Nathalie; Swedrowska, Magda; Ingham, Stephen; Tomlin, Stephen; Forbes, Ben

    2016-01-07

    Circadin 2 mg prolonged-release tablet is the only licensed melatonin product available in the UK. Circadin is indicated for patients with primary insomnia aged 55 and over, but is more widely used "off-label" to treat sleep disorders especially in the paediatric population. Children and older people often have difficulty swallowing tablets and dividing the tablet is sometimes required to ease administration. The aim of this study was to measure the release profile of melatonin from Circadin tablets when divided or crushed, and compare this with release from intact tablets. Dissolution testing was also performed for unlicensed melatonin products for comparison. Dissolution tests were performed using the pharmacopoeial paddle apparatus, with melatonin release analyzed by high performance liquid chromatography. Melatonin content, hardness, friability, and disintegration of the products were also evaluated. The prolonged release of melatonin from Circadin tablets was unlike that of any other product tested. When divided into halves, Circadin preserved most of the prolonged-release characteristic (f2 = 58), whereas quarter-cut and crushed tablet had a more immediate melatonin release profile. Circadin is significantly less expensive and should be preferred to unlicensed medicines which are not pharmaceutically equivalent and offer less quality assurance.

  4. Lubricant-Induced Crystallization of Itraconazole From Tablets Made of Electrospun Amorphous Solid Dispersion.

    PubMed

    Démuth, Balázs; Farkas, Attila; Balogh, Attila; Bartosiewicz, Karolina; Kállai-Szabó, Barnabás; Bertels, Johny; Vigh, Tamás; Mensch, Jurgen; Verreck, Geert; Van Assche, Ivo; Marosi, György; Nagy, Zsombor K

    2016-09-01

    Investigation of downstream processing of nanofibrous amorphous solid dispersions to generate tablet formulation is in a quite early phase. Development of high speed electrospinning opened up the possibility to study tableting of electrospun solid dispersions (containing polyvinylpyrrolidone-vinyl acetate and itraconazole [ITR] in this case). This work was conducted to investigate the influence of excipients on dissolution properties and the feasibility of scaled-up rotary press tableting. The dissolution rates from tablets proved to be mainly composition dependent. Magnesium stearate acted as a nucleation promoting agent (providing an active hydrophobic environment for crystallization of ITR) hindering the total dissolution of ITR. This crystallization process proved to be temperature dependent as well. However, the extent of dissolution of more than 95% was realizable when a less hydrophobic lubricant, sodium stearyl fumarate (soluble in the medium), was applied. Magnesium stearate induced crystallization even if it was put in the dissolution medium next to proper tablets. After optimization of the composition, scaled-up tableting on a rotary press was carried out. Appropriate dissolution of ITR from tablets was maintained for 3 months at 25°C/60% relative humidity. HPLC measurements confirmed that ITR was chemically stable both in the course of downstream processing and storage. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  5. The facts that the physical-chemical properties of modern tablets distinguish them from natural food lumps

    NASA Astrophysics Data System (ADS)

    Urakov, A.; Urakova, N.; Reshetnikov, A.; Kopylov, M.; Kasatkin, A.; Baymurzin, D.; Gabdrafikov, R.

    2017-02-01

    It was found that pharmaceutical companies produce drugs in tablet form, physical or physical-chemical properties that are radically different from those of the properties of natural food lumps, in that adult converts food in our mouth before swallowing. It was shown that the conventional shape, color, size, volume, specific gravity, hardness, osmotic and acid activity of modern tablets impair the physical and physicochemical properties of the liquid contents of the stomach is much stronger than such “building” materials, such as chalk, clay, sand, river pebbles and gravel. The results showed, that the value of the specific hardness, deforming tablets, can distinguish modern tablets from each other by more than 5000 times. Therefore, introduction tablets inside without information of ability injuring their action leads to the fact that soft and “unsalted” tablets almost nothing damage, and too “salty” and solid tablets damage the gums, lips, tongue, teeth and dental structures. To reduce the traumatic action tablets offered standardize osmoticity, corrosion and hardness within the range of safe values for soft and hard tissues of the oral cavity and improve standard introduction of tablets in the mouth.

  6. Spectrum of tablet computer use by medical students and residents at an academic medical center.

    PubMed

    Robinson, Robert

    2015-01-01

    Introduction. The value of tablet computer use in medical education is an area of considerable interest, with preliminary investigations showing that the majority of medical trainees feel that tablet computers added value to the curriculum. This study investigated potential differences in tablet computer use between medical students and resident physicians. Materials & Methods. Data collection for this survey was accomplished with an anonymous online questionnaire shared with the medical students and residents at Southern Illinois University School of Medicine (SIU-SOM) in July and August of 2012. Results. There were 76 medical student responses (26% response rate) and 66 resident/fellow responses to this survey (21% response rate). Residents/fellows were more likely to use tablet computers several times daily than medical students (32% vs. 20%, p = 0.035). The most common reported uses were for accessing medical reference applications (46%), e-Books (45%), and board study (32%). Residents were more likely than students to use a tablet computer to access an electronic medical record (41% vs. 21%, p = 0.010), review radiology images (27% vs. 12%, p = 0.019), and enter patient care orders (26% vs. 3%, p < 0.001). Discussion. This study shows a high prevalence and frequency of tablet computer use among physicians in training at this academic medical center. Most residents and students use tablet computers to access medical references, e-Books, and to study for board exams. Residents were more likely to use tablet computers to complete clinical tasks. Conclusions. Tablet computer use among medical students and resident physicians was common in this survey. All learners used tablet computers for point of care references and board study. Resident physicians were more likely to use tablet computers to access the EMR, enter patient care orders, and review radiology studies. This difference is likely due to the differing educational and professional demands placed on

  7. Spectrum of tablet computer use by medical students and residents at an academic medical center

    PubMed Central

    2015-01-01

    Introduction. The value of tablet computer use in medical education is an area of considerable interest, with preliminary investigations showing that the majority of medical trainees feel that tablet computers added value to the curriculum. This study investigated potential differences in tablet computer use between medical students and resident physicians. Materials & Methods. Data collection for this survey was accomplished with an anonymous online questionnaire shared with the medical students and residents at Southern Illinois University School of Medicine (SIU-SOM) in July and August of 2012. Results. There were 76 medical student responses (26% response rate) and 66 resident/fellow responses to this survey (21% response rate). Residents/fellows were more likely to use tablet computers several times daily than medical students (32% vs. 20%, p = 0.035). The most common reported uses were for accessing medical reference applications (46%), e-Books (45%), and board study (32%). Residents were more likely than students to use a tablet computer to access an electronic medical record (41% vs. 21%, p = 0.010), review radiology images (27% vs. 12%, p = 0.019), and enter patient care orders (26% vs. 3%, p < 0.001). Discussion. This study shows a high prevalence and frequency of tablet computer use among physicians in training at this academic medical center. Most residents and students use tablet computers to access medical references, e-Books, and to study for board exams. Residents were more likely to use tablet computers to complete clinical tasks. Conclusions. Tablet computer use among medical students and resident physicians was common in this survey. All learners used tablet computers for point of care references and board study. Resident physicians were more likely to use tablet computers to access the EMR, enter patient care orders, and review radiology studies. This difference is likely due to the differing educational and professional demands placed on

  8. [Current situations and problem analysis of influencing factors of traditional Chinese medicine tablets on forming quality].

    PubMed

    Li, Yan-Nian; Wu, Zhen-Feng; Wan, Na; Li, Yuan-Hui; Li, Hui-Ting; Yang, Ming

    2018-04-01

    The compressibility of tablets is the essential operating unit during the preparation of traditional Chinese medicine tablets, as well as a complicated process. Therefore, it is of great significance to comprehensively study the influencing factors on the formation process. This paper aimed to review the evaluation methods for the tablet forming quality and highlight the effects of material powder properties, excipients and preparation technology on the quality of traditional Chinese medicine tablets on the basis of relevant literatures. Furthermore, the common problems in tablet forming process are also analyzed to provide useful references for the development of tablet forming quality of traditional Chinese medicines. Copyright© by the Chinese Pharmaceutical Association.

  9. Growth of potassium niobate micro-hexagonal tablets with monoclinic phase and its excellent piezoelectric property

    NASA Astrophysics Data System (ADS)

    Chen, Zhong; Huang, Jingyun; Wang, Ye; Yang, Yefeng; Wu, Yongjun; Ye, Zhizhen

    2012-09-01

    Potassium niobate micro-hexagonal tablets were synthesized through hydrothermal reaction with KOH, H2O and Nb2O5 as source materials by using a polycrystalline Al2O3 as substrate. X-ray diffraction, Raman spectra and selected area electron diffraction analysis results indicated that the tablets exhibit monoclinic phase structure and are highly crystallized. Meanwhile, piezoelectric property of the micro-hexagonal tablets was investigated. The as-synthesized tablets exhibit excellent piezoactivities in the experiments, and an effective piezoelectric coefficient of around 80 pm/V was obtained. The tablets have huge potential applications in micro/nano-integrated piezoelectric and optical devices.

  10. Magnetic resonance imaging and X-ray microtomography studies of a gel-forming tablet formulation.

    PubMed

    Laity, P R; Mantle, M D; Gladden, L F; Cameron, R E

    2010-01-01

    The capabilities of two methods for investigating tablet swelling are investigated, based on a study of a model gel-forming system. Results from magnetic resonance imaging (MRI) were compared with results from a novel application of X-ray microtomography (XmicroT) to track the movements of embedded glass microsphere tracers as the model tablets swelled. MRI provided information concerning the movement of hydration fronts into the tablets and the composition of the swollen gel layer, which formed at the tablet surface and progressively thickened with time. Conversely, XmicroT revealed significant axial expansion within the tablet core, at short times and ahead of the hydration fronts, where there was insufficient water to be observed by MRI (estimated to be around 15% by weight for the system used here). Thus, MRI and XmicroT may be regarded as complementary methods for studying the hydration and swelling behaviour of tablets. Copyright 2009 Elsevier B.V. All rights reserved.

  11. Patient difficulty using tablet computers to screen in primary care.

    PubMed

    Hess, Rachel; Santucci, Aimee; McTigue, Kathleen; Fischer, Gary; Kapoor, Wishwa

    2008-04-01

    Patient-administered computerized questionnaires represent a novel tool to assist primary care physicians in the delivery of preventive health care. The aim of this study was to assess patient-reported ease of use with a self-administered tablet computer-based questionnaire in routine clinical care. All patients seen in a university-based primary care practice were asked to provide routine screening information using a touch-screen tablet computer-based questionnaire. Patients reported difficulty using the tablet computer after completion of their first questionnaire. Ten thousand nine hundred ninety-nine patients completed the questionnaire between January 2004 and January 2006. We calculated rates of reporting difficulty (no difficulty, some difficulty, or a lot of difficulty) using the tablet computers based on patient age, sex, race, educational attainment, marital status, and number of comorbid medical conditions. We constructed multivariable ordered logistic models to identify predictors of increased self-reported difficulty using the computer. The majority of patients (84%) reported no difficulty using the tablet computers to complete the questionnaire, with only 3% reporting a lot of difficulty. Significant predictors of reporting more difficulty included increasing age [odds ratio (OR) 1.05, 95% confidence interval (CI) 1.05-1.05)]; Asian race (OR 2.3, 95% CI 1.8-2.9); African American race (OR 1.4, 95% CI 1.2-1.6); less than a high school education (OR 3.0, 95% CI 2.6-3.4); and the presence of comorbid medical conditions (1-2: OR 1.3, 95% CI 1.2-1.5; > or =3: OR 1.7 95% CI 1.5-2.1). The majority of primary care patients reported no difficulty using a self-administered tablet computer-based questionnaire. While computerized questionnaires present opportunities to collect routine screening information from patients, attention must be paid to vulnerable groups.

  12. A study of tablet dissolution by magnetic resonance electric current density imaging.

    PubMed

    Mikac, Ursa; Demsar, Alojz; Demsar, Franci; Sersa, Igor

    2007-03-01

    The electric current density imaging technique (CDI) was used to monitor the dissolution of ion releasing tablets (made of various carboxylic acids and of sodium chloride) by following conductivity changes in an agar-agar gel surrounding the tablet. Conductivity changes in the sample were used to calculate spatial and temporal changes of ionic concentrations in the sample. The experimental data for ion migration were compared to a mathematical model based on a solution of the diffusion equation with moving boundary conditions for the tablet geometry. Diffusion constants for different acids were determined by fitting the model to the experimental data. The experiments with dissolving tablets were used to demonstrate the potential of the CDI technique for measurement of ion concentration in the vicinity of ion releasing samples.

  13. Ragweed sublingual tablet immunotherapy: part I - evidence-based clinical efficacy and safety.

    PubMed

    Creticos, Peter Socrates; Pfaar, Oliver

    2018-06-01

    Sublingual tablet immunotherapy provides an attractive alternative approach to allergen immunotherapy, as the allergen is administered as a rapidly dissolving sublingual tablet. Part I of this two-part series on the ragweed sublingual tablet describes the dose-ranging clinical work, the safety studies and the clinical outcomes from the pivotal trials which provide clear evidence for statistically significant and clinically meaningful benefit in the treatment of patients suffering from ragweed-induced seasonal allergic rhinitis-conjunctivitis with or without milder asthma. The robust results observed in the clinical trials performed with the ragweed sublingual tablet are defined by the quality of their study design, their use of a standardized allergen extract, their consistent reproducibility in demonstrating therapeutic efficacy and their properly quantified and graded safety data.

  14. Tablet Use in Primary Education: Adoption Hurdles and Attitude Determinants

    ERIC Educational Resources Information Center

    van Deursen, Alexander J. A. M.; ben Allouch, Somaya; Ruijter, Laura P.

    2016-01-01

    In the Netherlands, six primary schools recently participated in a pilot program, creating an educational environment in which children use a tablet PC. In these six schools, two studies are conducted. The first study highlights the process by which primary schools adopted tablet PCs by means of interviews based on diffusion of innovation theory.…

  15. Conditions for the Effectiveness of a Tablet-Based Algebra Program

    ERIC Educational Resources Information Center

    Jaciw, Andrew P.; Toby, Megan; Ma, Boya

    2012-01-01

    Tablets such as the iPad represent the next iteration of technologies that hold promise to facilitate learning, particularly in mathematics. In the case of algebra, tablets have the potential to bring the curriculum to life by easily linking to supporting materials and they allow an interactive experience whereby manipulation of one type of…

  16. Modulation of venlafaxine hydrochloride release from press coated matrix tablet.

    PubMed

    Gohel, M C; Soni, C D; Nagori, S A; Sarvaiya, K G

    2008-01-01

    The aim of present study was to prepare novel modified release press coated tablets of venlafaxine hydrochloride. Hydroxypropylmethylcellulose K4M and hydroxypropylmethylcellulose K100M were used as release modifier in core and coat, respectively. A 3(2) full factorial design was adopted in the optimization study. The drug to polymer ratio in core and coat were chosen as independent variables. The drug release in the first hour and drug release rate between 1 and 12 h were chosen as dependent variables. The tablets were characterized for dimension analysis, crushing strength, friability and in vitro drug release. A check point batch, containing 1:2.6 and 1:5.4 drug to polymer in core and coat respectively, was prepared. The tablets of check point batch were subjected to in vitro drug release in dissolution media with pH 5, 7.2 and distilled water. The kinetics of drug release was best explained by Korsmeyer and Peppas model (anomalous non-Fickian diffusion). The systematic formulation approach enabled us to develop modified release venlafaxine hydrochloride tablets.

  17. Bridging the Divide: Using UTAUT to predict multigenerational tablet adoption practices.

    PubMed

    Magsamen-Conrad, Kate; Upadhyaya, Shrinkhala; Joa, Claire Youngnyo; Dowd, John

    2015-09-01

    This study examined the "Unified Theory of Acceptance and Use of Technology" (UTAUT) in the context of tablet devices across multiple generations. We tested the four UTAUT determinants, performance expectancy, effort expectancy, social influence, and facilitating conditions, to determine their contributions for predicting behavioral intention to use tablets with age, gender, and user experience as moderators. 899 respondents aged 19-99 completed the survey. We found consistent generational differences in UTAUT determinants, most frequently between the oldest and youngest generations. Effort expectancy and facilitating conditions were the only determinants that positively predicted tablet use intentions after controlling for age, gender, and tablet use. We also discuss the implications of ageism and gender discrimination of technology adoption. Finally, we argue that our findings can be extended to create effective training programs for the teaching, learning, and adoption of new technologies in a variety of organizational settings.

  18. Bridging the Divide: Using UTAUT to predict multigenerational tablet adoption practices

    PubMed Central

    Magsamen-Conrad, Kate; Upadhyaya, Shrinkhala; Joa, Claire Youngnyo; Dowd, John

    2015-01-01

    This study examined the “Unified Theory of Acceptance and Use of Technology” (UTAUT) in the context of tablet devices across multiple generations. We tested the four UTAUT determinants, performance expectancy, effort expectancy, social influence, and facilitating conditions, to determine their contributions for predicting behavioral intention to use tablets with age, gender, and user experience as moderators. 899 respondents aged 19–99 completed the survey. We found consistent generational differences in UTAUT determinants, most frequently between the oldest and youngest generations. Effort expectancy and facilitating conditions were the only determinants that positively predicted tablet use intentions after controlling for age, gender, and tablet use. We also discuss the implications of ageism and gender discrimination of technology adoption. Finally, we argue that our findings can be extended to create effective training programs for the teaching, learning, and adoption of new technologies in a variety of organizational settings. PMID:25937699

  19. Tablet PC as a mobil PACS terminal using wireless LAN

    NASA Astrophysics Data System (ADS)

    Tsao, Bo-Shen; Ching, Yu-Tai; Lee, Wen-Jeng; Chen, Shyh-Jye; Chang, Chia-Hung; Chen, Chien-Jung; Yen, York; Lee, Yuan-Ten

    2003-05-01

    A PACS mobile terminal has applications in ward round, emergency room and remote teleradiology consultation. Personal Digital Assistants (PDAs) have the highest mobility and are used for many medical applications. However, their roles are limited in the field of radiology due to small screen size. In this study, we built a wireless PACS terminal using a hand-held tablet-PC. A tablet PC (X-pilot, LEO systems, Taiwan) running the WinCE operating systems was used as our mobile PACS terminal. This device is equipped with 800×600 resolution 10.4 inch TFT monitor. The network connection between the tablet PC and the server was linked via wireless LAN (IEEE 802.11b).

  20. Relationship between diffusivity of water molecules inside hydrating tablets and their drug release behavior elucidated by magnetic resonance imaging.

    PubMed

    Kikuchi, Shingo; Onuki, Yoshinori; Kuribayashi, Hideto; Takayama, Kozo

    2012-01-01

    We reported previously that sustained release matrix tablets showed zero-order drug release without being affected by pH change. To understand drug release mechanisms more fully, we monitored the swelling and erosion of hydrating tablets using magnetic resonance imaging (MRI). Three different types of tablets comprised of polyion complex-forming materials and a hydroxypropyl methylcellulose (HPMC) were used. Proton density- and diffusion-weighted images of the hydrating tablets were acquired at intervals. Furthermore, apparent self-diffusion coefficient maps were generated from diffusion-weighted imaging to evaluate the state of hydrating tablets. Our findings indicated that water penetration into polyion complex tablets was faster than that into HPMC matrix tablets. In polyion complex tablets, water molecules were dispersed homogeneously and their diffusivity was relatively high, whereas in HPMC matrix tablets, water molecule movement was tightly restricted within the gel. An optimal tablet formulation determined in a previous study had water molecule penetration and diffusivity properties that appeared intermediate to those of polyion complex and HPMC matrix tablets; water molecules were capable of penetrating throughout the tablets and relatively high diffusivity was similar to that in the polyion complex tablet, whereas like the HPMC matrix tablet, it was well swollen. This study succeeded in characterizing the tablet hydration process. MRI provides profound insight into the state of water molecules in hydrating tablets; thus, it is a useful tool for understanding drug release mechanisms at a molecular level.

  1. 75 FR 61503 - Determination That AZDONE (Hydrocodone Bitartrate and Aspirin) Tablet, 5 Milligrams/500...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-05

    ...] Determination That AZDONE (Hydrocodone Bitartrate and Aspirin) Tablet, 5 Milligrams/500 Milligrams, Was Not... bitartrate and aspirin) Tablet, 5 milligrams (mg)/ 500 mg, was not withdrawn from sale for reasons of safety... (ANDAs) for hydrocodone bitartrate and aspirin tablet, 5 mg/500 mg, if all other legal and regulatory...

  2. Novel levocetirizine HCl tablets with enhanced palatability: synergistic effect of combining taste modifiers and effervescence technique

    PubMed Central

    Labib, Gihan S

    2015-01-01

    Objectives Levocetirizine HCl, a second-generation piperazine derivative and H1-selective antihistaminic agent, possesses few side effects. The first objective of the study was to compare and evaluate the taste-masking effect of different ratios of 2-hydroxypropyl-β-cyclodextrin and mannitol on levocetirizine HCl using an inclusion complex and solid dispersion, respectively. The second objective was to study the possibility of preparing and evaluating effervescent tablets from the best-chosen taste-masked blends for the purpose of their use either as orodispersible tablets or as water-soluble effervescent tablets, according to patients’ will. Materials and methods Prepared taste-masked blends were prepared and subjected to palatability, Fourier-transform infrared spectroscopy, and differential scanning calorimetry studies. Tablets containing different percentages of effervescent mixtures were prepared by direct compression on the selected taste-modified blends. Evaluation tests were conducted, including flowability and compressibility on the precompressed blends and hardness, friability, wetting time, effervescent time, in vitro, in vivo disintegration time, and in vitro dissolution study on the compressed tablets. Formulated tablets were evaluated and compared to marketed orodispersible tablets for mouth feel and palatability. Results All prepared tablets showed convenient physical and palatability properties compared to the selected brand. The in vitro drug-release study revealed fast release of levocetirizine HCl within 5 minutes from all prepared tablets. Conclusion Levocetirizine HCl effervescent tablets are likely to increase patient compliance with drug administration. Moreover, the use of these effervescent tablets in an orodispersible dosage form can improve oral drug bioavailability and act as an attractive pediatric dosage form. PMID:26379426

  3. Dextrose monohydrate as a non-animal sourced alternative diluent in high shear wet granulation tablet formulations.

    PubMed

    Mitra, Biplob; Wolfe, Chad; Wu, Sy-Juen

    2018-05-01

    The feasibility of dextrose monohydrate as a non-animal sourced diluent in high shear wet granulation (HSWG) tablet formulations was determined. Impacts of granulation solution amount and addition time, wet massing time, impeller speed, powder and solution binder, and dry milling speed and screen opening size on granule size, friability and density, and tablet solid fraction (SF) and tensile strength (TS) were evaluated. The stability of theophylline tablets TS, disintegration time (DT) and in vitro dissolution were also studied. Following post-granulation drying at 60 °C, dextrose monohydrate lost 9% water and converted into the anhydrate form. Higher granulation solution amounts and faster addition, faster impeller speeds, and solution binder produced larger, denser and stronger (less friable) granules. All granules were compressed into tablets with acceptable TS. Contrary to what is normally observed, denser and larger granules (at ≥21% water level) produced tablets with a higher TS. The TS of the weakest tablets increased the most after storage at both 25 °C/60% RH and 40 °C/75% RH. Tablet DT was higher for stronger granules and after storage. Tablet dissolution profiles for 21% or less water were comparable and did not change on stability. However, the dissolution profile for tablets prepared with 24% water was slower initially and continued to decrease on stability. The results indicate a granulation water amount of not more than 21% is required to achieve acceptable tablet properties. This study clearly demonstrated the utility of dextrose monohydrate as a non-animal sourced diluent in a HSWG tablet formulation.

  4. Hot-stage microscopy for determination of API particles in a formulated tablet.

    PubMed

    Simek, Michal; Grünwaldová, Veronika; Kratochvíl, Bohumil

    2014-01-01

    Although methods exist to readily determine the particle size distribution (PSD) of an active pharmaceutical ingredient (API) before its formulation into a final product, the primary challenge is to develop a method to determine the PSD of APIs in a finished tablet. To address the limitations of existing PSD methods, we used hot-stage microscopy to observe tablet disintegration during temperature change and, thus, reveal the API particles in a tablet. Both mechanical and liquid disintegration were evaluated after we had identified optimum milling time for mechanical disintegration and optimum volume of water for liquid disintegration. In each case, hot-stage micrographs, taken before and after the API melting point, were compared with image analysis software to obtain the PSDs. Then, the PSDs of the APIs from the disintegrated tablets were compared with the PSDs of raw APIs. Good agreement was obtained, thereby confirming the robustness of our methodology. The availability of such a method equips pharmaceutical scientists with an in vitro assessment method that will more reliably determine the PSD of active substances in finished tablets.

  5. Efficacy of Nimodipine Plus Yufeng Ningxin Tablets for Patients with Frequent Migraine.

    PubMed

    Mu, Hongmei; Wang, Liyong

    2018-06-07

    To test the effects of Nimodipine plus Yufeng Ningxin tablets on frequent migraine. Two hundred forty-two patients with frequent migraine were divided into the control group with those consuming Flunarizine (120 cases) and the treatment group with those consuming Nimodipine plus Yufeng Ningxin tablets (122 cases). The course of frequent migraine treatment lasted 7 weeks. The number of migraine days, visual analogue scale (VAS) score, and response rate were measured. There was significant difference in the cure rate as the Nimodipine plus Yufeng Ningxin tablets group compared with the Flunarizine group (78.7 vs. 21.7%; p < 0.001). Fewer migraine days and VAS score were observed in the treatment group when compared with the control group (p < 0.05). Nimodipine plus Yufeng Ningxin tablets were superior to Flunarizine in terms of the response rate at week 7 (p < 0.05). Due to its high cure rate, treatment with Nimodipine plus Yufeng Ningxin tablets is recommended to control frequent migraine, and this hypothesis needs to be confirmed through further studies conducted on a more extensive population. © 2018 S. Karger AG, Basel.

  6. Validating the Accuracy of Reaction Time Assessment on Computer-Based Tablet Devices.

    PubMed

    Schatz, Philip; Ybarra, Vincent; Leitner, Donald

    2015-08-01

    Computer-based assessment has evolved to tablet-based devices. Despite the availability of tablets and "apps," there is limited research validating their use. We documented timing delays between stimulus presentation and (simulated) touch response on iOS devices (3rd- and 4th-generation Apple iPads) and Android devices (Kindle Fire, Google Nexus, Samsung Galaxy) at response intervals of 100, 250, 500, and 1,000 milliseconds (ms). Results showed significantly greater timing error on Google Nexus and Samsung tablets (81-97 ms), than Kindle Fire and Apple iPads (27-33 ms). Within Apple devices, iOS 7 obtained significantly lower timing error than iOS 6. Simple reaction time (RT) trials (250 ms) on tablet devices represent 12% to 40% error (30-100 ms), depending on the device, which decreases considerably for choice RT trials (3-5% error at 1,000 ms). Results raise implications for using the same device for serial clinical assessment of RT using tablets, as well as the need for calibration of software and hardware. © The Author(s) 2015.

  7. Study of controlled-release floating tablets of dipyridamole using the dry-coated method.

    PubMed

    Chen, Kai; Wen, Haoyang; Yang, Feifei; Yu, Yibin; Gai, Xiumei; Wang, Haiying; Li, Pingfei; Pan, Weisan; Yang, Xinggang

    2018-01-01

    Dipyridamole (DIP), having a short biological half-life, has a narrow absorption window and is primarily absorbed in the stomach. So, the purpose of this study was to prepare controlled-release floating (CRF) tablets of dipyridamole by the dry-coated method. The influence of agents with different viscosity, hydroxypropylmethylcellulose (HPMC) and polyvinylpyrollidon K30 (PVP K30) in the core tablet and low-viscosity HPMC and PVP K30 in the coating layer on drug release, were investigated. Then, a study with a three-factor, three-level orthogonal experimental design was used to optimize the formulation of the CRF tablets. After data processing, the optimized formulation was found to be: 80 mg HPMC K4M in the core tablet, 80 mg HPMC E15 in core tablet and 40 mg PVP K30 in the coating layer. Moreover, an in vitro buoyancy study showed that the optimized formulation had an excellent floating ability and could immediately float without a lag time and this lasted more than 12 h. Furthermore, an in vivo gamma scintigraphic study showed that the gastric residence time of the CRF tablet was about 8 h.

  8. Is online information on ecstasy tablet content safe?

    PubMed

    Vrolijk, Ruben Q; Brunt, Tibor M; Vreeker, Annabel; Niesink, Raymond J M

    2017-01-01

    In recent years, the prevalence of ecstasy use has increased in most European countries. Users can acquire information on ecstasy tablet composition through the internet. This study compares online information from two websites, Pillreports and Partyflock, to the validated Dutch Drugs Information and Monitoring System (DIMS) database, and aims to measure its accuracy and potential danger or value. The drug-related information posted on Pillreports.net and Partyflock.nl between 1 January 2014 and 31 December 2015 was investigated for accuracy and several information characteristics such as picture inclusion and dose range inclusion. In total, 471 informatory statements on ecstasy tablet content were analysed relative to the Dutch ecstasy market. Informatory statements on the content of specific ecstasy tablets were scored as 'too high' or 'too low' if their concentrations deviated > 10 mg from the entries in the DIMS database within a 12-week time-frame, and scored as 'dangerous' if their concentration was > 40 mg too low. Unreported substances were scored as 'dangerous' if listed as an illegal or dangerous substance in the DIMS database and if present in relevant quantities. Also scored were the report characteristics 'picture inclusion', 'spread inclusion' and 'website source', which were tested for their association with report safety/danger. On average, reports on ecstasy tablets from Pillreports and Partyflock show concentrations which are 10.6 mg too high [95% confidence interval (CI) = 6.7-14.4]. Qualitatively, 39.7% of the reports scored as 'too high' (95% CI = 35.2-44.4), 17.6% scored as 'too low' (95% CI = 14.0-21.2) and 15.5% had 'unreported substances' (95% CI = 12.3-18.9), resulting overall in 15.3% of the reports being scored as 'dangerous' (95% CI = 11.9-18.5). The report characteristic 'spread inclusion' associated inversely with report danger [Exp(b) = 0.511, 95% CI = 0.307-0.850, P = 0.01]. Information from the popular

  9. Students' Opinions on the Use of Tablet Computers in Education

    ERIC Educational Resources Information Center

    Duran, Muharrem; Aytaç, Tufan

    2016-01-01

    One of the most important tools for the integration of ICT in education, especially with tablet computers, has been employed in Turkey through the FATIH Project. This study aimed to determine students' views on the use of tablet computers in learning and teaching processes. Eighty-four first-year high school students studying at three schools in…

  10. Tablets in English Class: Students' Activities Surrounding Online Dictionary Work

    ERIC Educational Resources Information Center

    Bunting, Leona

    2015-01-01

    Tablets have become increasingly popular among young people in Sweden and this rapid increase also resonates in school, especially in classrooms for younger children. The aim of the present study is to analyze and describe how the students deal with the open instructions for a task of using online dictionaries on tablets. Specific focus is on how…

  11. Effect of antacids in didanosine tablet on bioavailability of isoniazid.

    PubMed

    Gallicano, K; Sahai, J; Zaror-Behrens, G; Pakuts, A

    1994-04-01

    The antacids in two didanosine placebo tablets had no significant effect on the plasma pharmacokinetics of a single oral dose of 300 mg of isoniazid administered to 12 healthy volunteers. These results suggest that isoniazid bioavailability will be unaffected by the antacids in didanosine tablets when the two medications are administered simultaneously to human immunodeficiency virus-seropositive patients.

  12. CES 2011: Tablet Crazy

    ERIC Educational Resources Information Center

    Rapp, David

    2011-01-01

    Ereaders are so last year. Tablets were the watchword at this year's annual Consumer Electronics Show (CES) in Las Vegas, January 6-9. This year, the show set new records, with some 2700 companies from around the world exhibiting at the multiple exhibition halls and 30,000 attendees gawking at the products. What did they see? There were still some…

  13. The effect of excipients on the stability of levothyroxine sodium pentahydrate tablets.

    PubMed

    Patel, Himanshu; Stalcup, Apryll; Dansereau, Richard; Sakr, Adel

    2003-10-02

    Levothyroxine tablets, 50 microg, have been marketed for many decades but have had numerous recalls due to degradation and failure to meet potency. These experiments were devised to study the effects of various excipients on the stability of levothyroxine sodium pentahydrate in aqueous slurries and in formulated tablets. The active alone was found to be stable in the solid state for 6 months at 40 degrees C/75% RH whether stored in open or closed containers, and was found to be non-hygroscopic under normal processing conditions (>30% RH). In aqueous slurries with an excipient, the stability of the active improved as the pH of the slurry was increased from pH 3 to 11. Tablets manufactured with lactose anhydrous, starch, or microcrystalline cellulose failed to meet USP assay requirements at 3 months at 40 degrees C/75% RH. Tablets manufactured with dibasic calcium phosphate or mannitol met USP assay requirements at 3, but not 6 months when stored at 40 degrees C/75% RH. Tablets manufactured with dibasic calcium phosphate and a basic pH modifier, such as sodium carbonate, sodium bicarbonate, or magnesium oxide, met the USP assay requirements at both 3 and 6 months. Thus, the use of basic pH modifiers is a potential technique for improving the stability of levothyroxine sodium pentahydrate tablets.

  14. Formulation and Characterization of Oral Mucoadhesive Chlorhexidine Tablets Using Cordia myxa Mucilage

    PubMed Central

    Moghimipour, Eskandar; Aghel, Nasrin; Adelpour, Akram

    2012-01-01

    Background The dilution and rapid elimination of topically applied drugs due to the flushing action of saliva is a major difficulty in the effort to eradicate infections of oral cavity. Utilization a proper delivery system for incorporation of drugs has a major impact on drug delivery and such a system should be formulated for prolonged drug retention in oral cavity. Objectives The aim of the present study was the use of mucilage of Cordia myxa as a mucoadhesive material in production of chlorhexidine buccal tablets and its substitution for synthetic polymers such as HPMC. Materials and Methods The influence of mucilage concentration on the physicochemical responses (hardness, friability, disintegration time, dissolution, swelling, and muco-adhesiveness strength) was studied and swelling of mucilage and HPMC were compared. The evaluated responses included pharmacopoeial characteristics of tablets, the force needed to separate tablets from mucosa, and the amount of water absorbed by tablets. Results In comparison to HPMC, the rise of mucilage concentration in the formulations increased disintegration time, drug dissolution rate, and reduced MDT. Also, compared to 30% HPMC, muco-adhesiveness strength of buccal tablets containing 20% mucilage was significantly higher. Conclusions It can be concluded that the presence of Cordia myxa powdered mucilage may significantly affect the tablet characteristics, and increasing in muco-adhesiveness may be achieved by using 20% w/w mucilage. PMID:24624170

  15. Neem gum as a binder in a formulated paracetamol tablet with reference to Acacia gum BP.

    PubMed

    Ogunjimi, Abayomi Tolulope; Alebiowu, Gbenga

    2014-04-01

    This study determined the physical, compressional, and binding properties of neem gum (NMG) obtained from the trunk of Azadirachta indica (A Juss) in a paracetamol tablet formulation in comparison with official Acacia gum BP (ACA). The physical and flow properties were evaluated using density parameters: porosity, Carr's index, Hausner's ratio, and flow rate. Compressional properties were analyzed using Heckel and Kawakita equations. The tensile strength, brittle fracture index, and crushing strength-friability/disintegration time ratio were used to evaluate the mechanical properties of paracetamol tablets while the drug release properties of the tablets were assessed using disintegration time and dissolution times. Tablet formulations containing NMG exhibited faster onset and higher amount of plastic deformation during compression than those containing ACA. Neem gum produced paracetamol tablets with lower mechanical strength; however, the tendency of the tablets to cap or laminate was lower when compared to those containing ACA. Inclusion of NMG improved the balance between binding and disintegration properties of paracetamol tablets produced than those containing ACA. Neem gum produced paracetamol tablets with lower disintegration and dissolution times than those containing ACA.

  16. In vitro-in vivo correlation for wet-milled tablet of poorly water-soluble cilostazol.

    PubMed

    Jinno, Jun-ichi; Kamada, Naoki; Miyake, Masateru; Yamada, Keigo; Mukai, Tadashi; Odomi, Masaaki; Toguchi, Hajime; Liversidge, Gary G; Higaki, Kazutaka; Kimura, Toshikiro

    2008-08-25

    The purpose of the present study was to investigate oral bioavailability of an immediate release tablet containing wet-milled crystals of a poorly water-soluble drug, cilostazol, and to establish in vitro-in vivo correlation. Sub-micron sized cilostazol (median diameter: 0.26 microm) was successfully prepared using a beads-mill in water in the presence of a hydrophilic polymer and an anionic surfactant. The milled suspension was solidified with a sugar alcohol as a water-soluble carrier by spray-drying method. The co-precipitate was compressed into an immediate release tablet with common excipients. Oral bioavailability of the wet-milled cilostazol tablet in male beagle dogs was 13-fold higher than the hammer-milled commercial tablet in fasted condition. Food did not increase the oral bioavailability of the wet-milled tablet, while 4-fold increase was found for the commercial tablet. Irrespective to the bioavailability enhancement, in vitro dissolution rate of the wet-milled tablet was even slower than the commercial tablet by the compendial method (USP Apparatus 2). On the other hand, a good correlation was found between the dissolution profiles obtained by a flow-through cell method (USP Apparatus 4, closed-loop system without outlet filter) using a large volume of water and sodium lauryl sulfate (SLS) solution at the concentration lower than the critical micellar concentration (cmc) as dissolution media corresponding to the fasted and fed conditions, respectively.

  17. Bioavailability of House Dust Mite Allergens in Sublingual Allergy Tablets Is Highly Dependent on the Formulation.

    PubMed

    Ohashi-Doi, Katsuyo; Kito, Hirokazu; Du, Weibin; Nakazawa, Hiroshi; Ipsen, Henrik; Gudmann, Pernille; Lund, Kaare

    2017-01-01

    In sublingual immunotherapy (SLIT), the immune system is addressed by solubilized allergen that interacts with immunocompetent cells of the oral mucosa, the efficiency of which is governed by 2 main factors of SLIT allergen bioavailability: the allergen concentration and the mucosal contact time. Recently, 3 house dust mite (HDM) SLIT tablets were developed that differ with regard to allergen content, nominal strength (maintenance doses: 6 SQ-HDM/10,000 Japanese Allergen Units [JAU], 12 SQ-HDM/ 20,000 JAU, and 300 IR/57,000 JAU), and formulation (freeze-dried/compressed). Here, the importance of the SLIT tablet formulation for HDM major allergen bioavailability is examined. The HDM major allergen content, tablet disintegration times, and allergen release kinetics were determined. Dissolution kinetics (allergen concentration vs. time) of Der f 1, Der p 1, and Der 2 were measured. Area under the curve (AUC) was used as a surrogate parameter for allergen bioavailability. The release of HDM major allergens from the freeze-dried tablets was complete after 30 s, while only partial release was achieved with the compressed tablets, even after prolonged dissolution. At 1 min, i.e., the recommended sublingual holding time for the freeze-dried tablets, the allergen bioavailability (AUC) of the compressed 300 IR/57,000 JAU tablet was 4.7-fold (Der f 1), 10.8-fold (Der p 1), and 23.6-fold (Der 2) lower than that of the freeze-dried 12 SQ-HDM/20,000 JAU tablet and similar to (Der f 1) and 5.3-fold (Der p 1) and 12.5-fold (Der 2) lower than that of the freeze-dried 6 SQ-HDM/10,000 JAU tablet. SLIT tablet allergen bioavailability depends highly on the tablet formulation. Only the fast-dissolving freeze-dried tablets provide maximal delivery of soluble allergens and achieve allergen concentrations that reflect the nominal tablet strengths within the recommended sublingual holding time. © 2017 S. Karger AG, Basel.

  18. Older Adults Perceptions of Technology and Barriers to Interacting with Tablet Computers: A Focus Group Study

    PubMed Central

    Vaportzis, Eleftheria; Giatsi Clausen, Maria; Gow, Alan J.

    2017-01-01

    Background: New technologies provide opportunities for the delivery of broad, flexible interventions with older adults. Focus groups were conducted to: (1) understand older adults' familiarity with, and barriers to, interacting with new technologies and tablets; and (2) utilize user-engagement in refining an intervention protocol. Methods: Eighteen older adults (65–76 years old; 83.3% female) who were novice tablet users participated in discussions about their perceptions of and barriers to interacting with tablets. We conducted three separate focus groups and used a generic qualitative design applying thematic analysis to analyse the data. The focus groups explored attitudes toward tablets and technology in general. We also explored the perceived advantages and disadvantages of using tablets, familiarity with, and barriers to interacting with tablets. In two of the focus groups, participants had previous computing experience (e.g., desktop), while in the other, participants had no previous computing experience. None of the participants had any previous experience with tablet computers. Results: The themes that emerged were related to barriers (i.e., lack of instructions and guidance, lack of knowledge and confidence, health-related barriers, cost); disadvantages and concerns (i.e., too much and too complex technology, feelings of inadequacy, and comparison with younger generations, lack of social interaction and communication, negative features of tablets); advantages (i.e., positive features of tablets, accessing information, willingness to adopt technology); and skepticism about using tablets and technology in general. After brief exposure to tablets, participants emphasized the likelihood of using a tablet in the future. Conclusions: Our findings suggest that most of our participants were eager to adopt new technology and willing to learn using a tablet. However, they voiced apprehension about lack of, or lack of clarity in, instructions and support

  19. Pharmaceutical and pharmacokinetic characterization of a novel sublingual buprenorphine/naloxone tablet formulation in healthy volunteers

    PubMed Central

    Fischer, Andreas; Hjelmström, Peter

    2015-01-01

    Abstract Context Bitter taste, as well as dissolve time, presents a significant challenge for the acceptability of formulations for oral transmucosal drug delivery. Objective To characterize a novel sublingual tablet formulation of buprenorphine/naloxone with regards to pharmacokinetics, dissolve time and formulation acceptability. Methods Dry mixing techniques were employed to produce a small and fast dissolving buprenorphine/naloxone sublingual tablet formulation, OX219 (Zubsolv®), using sucralose and menthol as sweetener and flavor to mask the bitter taste of the active ingredients. Two cross-over studies were performed in healthy volunteers to evaluate pharmacokinetics, dissolve time and acceptability of OX219 5.7/1.4 mg tablets compared to the commercially available buprenorphine/naloxone formulations Suboxone® tablets and films (8/2 mg). Results Buprenorphine exposure was equivalent in OX219 and Suboxone tablets. Sublingual dissolve times were significantly shorter for OX219 than for Suboxone tablets and were similar to Suboxone films. The OX219 formulation received significantly higher subjective ratings for taste and overall acceptability than both Suboxone formulations. OX219 was preferred over Suboxone tablet and film formulations by 77.4% and 88.9% of subjects, respectively. Conclusions A sublingual tablet formulation with an improved acceptability has been successfully developed. PMID:24099551

  20. Effects of excipients and curing process on the abuse deterrent properties of directly compressed tablets.

    PubMed

    Rahman, Ziyaur; Zidan, Ahmed S; Korang-Yeboah, Maxwell; Yang, Yang; Siddiqui, Akhtar; Shakleya, Diaa; Khan, Mansoor A; Cruz, Celia; Ashraf, Muhammad

    2017-01-30

    The objective of the present investigation was to understand the effects of excipients and curing process on the abuse deterrent properties (ADP) of Polyox™ based directly compressible abuse deterrent tablet formulations (ADFs). The excipients investigated were lactose (monohydrate or anhydrous), microcrystalline cellulose and hydroxypropyl methylcellulose. The ADPs studied were tablet crush resistance or hardness, particle size distribution following mechanical manipulation, drug extraction in water and alcohol, syringeability and injectability. Other non-ADPs such as surface morphology and tablet dissolution were also studied. It was found that presence of 50% or more of water soluble or swellable excipient in the ADF tablets significantly affected the tablet hardness, particle size distribution following mechanical manipulation and drug extraction while small amount (5%) of excipients had either minimal or no effect on ADPs of these tablets. Addition of high molecular weight HPMC (K 100M) affected syringeability and injectability of ADF. Curing process was found to affect ADPs (hardness, particle size distribution, drug extraction and syringeability and injectability) when compared with uncured tablet. In conclusion, addition of large amount of excipients, especially water soluble ones in Polyox™ based ADF tablets increase the risk of abuse by various routes of administration. Published by Elsevier B.V.