14 CFR 25.491 - Taxi, takeoff and landing roll.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Taxi, takeoff and landing roll. 25.491..., takeoff and landing roll. Within the range of appropriate ground speeds and approved weights, the airplane structure and landing gear are assumed to be subjected to loads not less than those obtained when the...

A Rapid Empirical Method for Estimating the Gross Takeoff Weight of a High Speed Civil Transport

NASA Technical Reports Server (NTRS)

Mack, Robert J.

1999-01-01

During the cruise segment of the flight mission, aircraft flying at supersonic speeds generate sonic booms that are usually maximum at the beginning of cruise. The pressure signature with the shocks causing these perceived booms can be predicted if the aircraft's geometry, Mach number, altitude, angle of attack, and cruise weight are known. Most methods for estimating aircraft weight, especially beginning-cruise weight, are empirical and based on least- square-fit equations that best represent a body of component weight data. The empirical method discussed in this report used simplified weight equations based on a study of performance and weight data from conceptual and real transport aircraft. Like other weight-estimation methods, weights were determined at several points in the mission. While these additional weights were found to be useful, it is the determination of beginning-cruise weight that is most important for the prediction of the aircraft's sonic-boom characteristics.

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Turbine engine powered: Takeoff... Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine powered airplane may take off that airplane at a weight greater than that listed in the...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Turbine engine powered: Takeoff... Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine powered airplane may take off that airplane at a weight greater than that listed in the...

14 CFR 23.703 - Takeoff warning system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.703 Takeoff warning system. For all airplanes with a maximum weight more than 6,000...

Safety implications of allowing trucks with gross weight of 6,501.

DOT National Transportation Integrated Search

1976-01-01

From a review of relevant research studies and laws of other states, it was concluded that changing the speed limit for vehicles of 6,501-10,000 pound gross weight would be premature pending further evidence that trucks of this size do not significan...

Weight loss and improved gross motor coordination in children as a result of multidisciplinary residential obesity treatment.

PubMed

D'Hondt, Eva; Gentier, Ilse; Deforche, Benedicte; Tanghe, Ann; De Bourdeaudhuij, Ilse; Lenoir, Matthieu

2011-10-01

This study evaluated the short-term effectiveness of a multidisciplinary residential obesity treatment program by describing changes in body weight, related measures, and gross motor co-ordination. Secondarily, it was examined to what extent the amount of relative weight loss achieved by overweight and obese (OW/OB) participants explained the projected improvement in gross motor co-ordination. Thirty-six OW/OB children (aged 10.5 ± 1.4 years, 12 girls and 24 boys) were recruited at the Zeepreventorium VZW (De Haan, Belgium), where they followed a specific program consisting of moderate dietary restriction, psychological support, and physical activity. For reference purposes, an additional group of 36 age- and gender-matched healthy-weight (HW) children was included in the study. Anthropometric measures were recorded and gross motor co-ordination was assessed using the Körperkoordinationstest für Kinder (KTK) on two occasions with an interval of 4 months. Regardless of the test moment, OW/OB participants displayed significantly poorer KTK performances (P < 0.001). However, treatment was found to be efficacious in decreasing body weight (Δ 17.9 ± 3.1%, P < 0.001) and generating a significant progress in gross motor co-ordination performance, with a greater increase in KTK score(s) from baseline to re-test as compared to HW peers (P < 0.01). Within the OW/OB group, the amount of relative weight loss explained 26.9% of the variance in improvement in overall KTK performance. Therefore, multidisciplinary residential treatment and concomitant weight loss can be considered an important means to upgrade OW/OB children's level of gross motor co-ordination, which in turn may promote physical activity participation.

What gross weight and range for an advanced HSCT?

NASA Technical Reports Server (NTRS)

Driver, Cornelius

1992-01-01

A review of studies conducted in 1986 indicates that a 300 passenger, 5500 nautical mile range aircraft should weigh less than 400,000 pounds. Some data from a British Aerospace Society of Automotive Engineers (SAE) paper will be shown that purport to be an advanced Concorde that meets the range payload specifications at a gross weight of 360,000 pounds. Previous studies by Peter Coen of Langley Research Center support these results. The weight of a supersonic transport is important from the point of view of how much effort should be expended in developing lower sonic boom technologies. It is obvious that a 360,000 pound aircraft can be modified to a more acceptable boom level than a 700,000 pound one.

Relationship Between Broiler Body Weights, Eimeria maxima Gross Lesion Scores, and Microscores in Three Anticoccidial Sensitivity Tests.

PubMed

Barrios, Miguel A; Da Costa, Manuel; Kimminau, Emily; Fuller, Lorraine; Clark, Steven; Pesti, Gene; Beckstead, Robert

2017-06-01

Anticoccidial sensitivity tests (ASTs) serve to determine the efficacy of anticoccidial drugs against Eimeria field isolates in a controlled laboratory setting. The most commonly measured parameters are body weight gain, feed conversion ratio, gross intestinal lesion scores, and mortality. Due to the difficulty in reliably scoring gross lesion scores of Eimeria maxima , microscopic analysis of intestinal scrapings (microscores) can be used in the field to indicate the presence of this particular Eimeria. The goal of this study was to determine the relationship between E. maxima microscores and broiler body weights and gross E. maxima lesion scores in three ASTs. Day-old broiler chicks were raised for 12 days on a standard corn-soy diet. On Day 12, chicks were placed in Petersime batteries and treatment diets were provided. There were six birds per pen, four pens per treatment, and 12 treatments, for a total of 288 chicks per AST. The treatments were as follows: 1) nonmedicated, noninfected; 2) nonmedicated, infected; 3) lasalocid, infected; 4) salinomycin, infected; 5) diclazuril, infected; 6) monensin, infected; 7) decoquinate, infected; 8) narasin + nicarbazin, infected; 9) narasin, infected; 10) nicarbazin, infected; 11) robenidine, infected; and 12) zoalene, infected. On Day 14, chicks were challenged with an Eimeria field isolate by oral gavage. On Day 20, broilers were weighed, and gross lesion scores and microscores were classified from 0 to 4 depending on the severity of the gross lesion scores and E. maxima microscores. Data from three trials using different field isolates were statistically analyzed using a logarithmic regression model. There was no relationship (P = 0.1224) between microscores and body weight gain. There was a positive relationship between microscores and gross lesion scores (P = 0.004). However, there was also an interaction between isolate and treatment (P < 0.0001). Lastly, the interaction between isolate and gross lesion scores (P

Aerodynamic Ground Effect in Fruitfly Sized Insect Takeoff

PubMed Central

Kolomenskiy, Dmitry; Maeda, Masateru; Engels, Thomas; Liu, Hao; Schneider, Kai; Nave, Jean-Christophe

2016-01-01

Aerodynamic ground effect in flapping-wing insect flight is of importance to comparative morphologies and of interest to the micro-air-vehicle (MAV) community. Recent studies, however, show apparently contradictory results of either some significant extra lift or power savings, or zero ground effect. Here we present a numerical study of fruitfly sized insect takeoff with a specific focus on the significance of leg thrust and wing kinematics. Flapping-wing takeoff is studied using numerical modelling and high performance computing. The aerodynamic forces are calculated using a three-dimensional Navier–Stokes solver based on a pseudo-spectral method with volume penalization. It is coupled with a flight dynamics solver that accounts for the body weight, inertia and the leg thrust, while only having two degrees of freedom: the vertical and the longitudinal horizontal displacement. The natural voluntary takeoff of a fruitfly is considered as reference. The parameters of the model are then varied to explore possible effects of interaction between the flapping-wing model and the ground plane. These modified takeoffs include cases with decreased leg thrust parameter, and/or with periodic wing kinematics, constant body pitch angle. The results show that the ground effect during natural voluntary takeoff is negligible. In the modified takeoffs, when the rate of climb is slow, the difference in the aerodynamic forces due to the interaction with the ground is up to 6%. Surprisingly, depending on the kinematics, the difference is either positive or negative, in contrast to the intuition based on the helicopter theory, which suggests positive excess lift. This effect is attributed to unsteady wing-wake interactions. A similar effect is found during hovering. PMID:27019208

Structural Sizing of a Horizontal Take-Off Launch Vehicle with an Air Collection and Enrichment System

NASA Technical Reports Server (NTRS)

McCurdy, David R.; Roche, Joseph M.

2004-01-01

In support of NASA's Next Generation Launch Technology (NGLT) program, the Andrews Gryphon booster was studied. The Andrews Gryphon concept is a horizontal lift-off, two-stage-to-orbit, reusable launch vehicle that uses an air collection and enrichment system (ACES). The purpose of the ACES is to collect atmospheric oxygen during a subsonic flight loiter phase and cool it to cryogenic temperature, ultimately resulting in a reduced initial take-off weight To study the performance and size of an air-collection based booster, an initial airplane like shape was established as a baseline and modeled in a vehicle sizing code. The code, SIZER, contains a general series of volume, surface area, and fuel fraction relationships that tie engine and ACES performance with propellant requirements and volumetric constraints in order to establish vehicle closure for the given mission. A key element of system level weight optimization is the use of the SIZER program that provides rapid convergence and a great deal of flexibility for different tank architectures and material suites in order to study their impact on gross lift-off weight. This paper discusses important elements of the sizing code architecture followed by highlights of the baseline booster study.

Aircraft Takeoff Characteristics

DOT National Transportation Integrated Search

2001-08-01

The document investigates three essential characteristics of takeoff; rotation point, liftoff : point, and takeoff angle. In this memorandum distributions of the data are provided and : analyzed. Trends in the data can be used to find the ideal locat...

A remote augmentor lift system with a turbine bypass engine

NASA Technical Reports Server (NTRS)

Fishbach, L. H.; Franciscus, L. C.

1982-01-01

Two supersonic vertical takeoff or landing (VTOL) aircraft engine types, a conventional medium bypass ratio turbofan, and a turbine bypass turbojet were studied. The aircraft assumed was a clipped delta wing with canard configuration. A VTOL deck launched intercept, DLI, mission with Mach 1.6 dash and cruise segments was used as the design mission. Several alternate missions requiring extended subsonic capabilities were analyzed. Comparisons were made between the turbofan (TF) and the turbine bypass turbojet (TBE) engines in airplane types using a Remote Augmented Lift Systems, RALS and a Lift plus Lift Cruise system (L+LC). The figure of merit was takeoff gross weight for the VTOL DLI mission. The results of the study show that the turbine bypass turbojet and the conventional turbofan are competitive engines for both type of aircraft in terms of takeoff gross weight and range. However, the turbine bypass turbojet would be a simpler engine and may result in more attractive life cycle costs and reduced maintenance. The RALS and L+LC airplane types with either TBE or TF engines have approximately the same aircraft takeoff gross weight.

NDARC NASA Design and Analysis of Rotorcraft - Input, Appendix 4

NASA Technical Reports Server (NTRS)

Johnson, Wayne

2016-01-01

The NDARC code performs design and analysis tasks. The design task involves sizing the rotorcraft to satisfy specified design conditions and missions. The analysis tasks can include off-design mission performance analysis, flight performance calculation for point operating conditions, and generation of subsystem or component performance maps. The principal tasks (sizing, mission analysis, flight performance analysis) are shown in the figure as boxes with heavy borders. Heavy arrows show control of subordinate tasks. The aircraft description consists of all the information, input and derived, that denes the aircraft. The aircraft consists of a set of components, including fuselage, rotors, wings, tails, and propulsion. This information can be the result of the sizing task; can come entirely from input, for a fixed model; or can come from the sizing task in a previous case or previous job. The aircraft description information is available to all tasks and all solutions. The sizing task determines the dimensions, power, and weight of a rotorcraft that can perform a specified set of design conditions and missions. The aircraft size is characterized by parameters such as design gross weight, weight empty, rotor radius, and engine power available. The relations between dimensions, power, and weight generally require an iterative solution. From the design flight conditions and missions, the task can determine the total engine power or the rotor radius (or both power and radius can be fixed), as well as the design gross weight, maximum takeoff weight, drive system torque limit, and fuel tank capacity. For each propulsion group, the engine power or the rotor radius can be sized. Missions are defined for the sizing task, and for the mission performance analysis. A mission consists of a number of mission segments, for which time, distance, and fuel burn are evaluated. For the sizing task, certain missions are designated to be used for design gross weight calculations; for

Aerodynamics and flow features of a damselfly in takeoff flight.

PubMed

Bode-Oke, Ayodeji T; Zeyghami, Samane; Dong, Haibo

2017-09-26

Flight initiation is fundamental for survival, escape from predators and lifting payload from one place to another in biological fliers and can be broadly classified into jumping and non-jumping takeoffs. During jumping takeoffs, the legs generate most of the initial impulse. Whereas the wings generate most of the forces in non-jumping takeoffs, which are usually voluntary, slow, and stable. It is of great interest to understand how these non-jumping takeoffs occur and what strategies insects use to generate large amount of forces required for this highly demanding flight initiation mode. Here, for the first time, we report accurate wing and body kinematics measurements of a damselfly during a non-jumping takeoff. Furthermore, using a high fidelity computational fluid dynamics simulation, we identify the 3D flow features and compute the wing aerodynamics forces to unravel the key mechanisms responsible for generating large flight forces. Our numerical results show that a damselfly generates about three times its body weight during the first half-stroke for liftoff. In generating these forces, the wings flap through a steeply inclined stroke plane with respect to the horizon, slicing through the air at high angles of attack (45°-50°). Consequently, a leading edge vortex (LEV) is formed during both the downstroke and upstroke on all the four wings. The formation of the LEV, however, is inhibited in the subsequent upstrokes following takeoff. Accordingly, we observe a drastic reduction in the magnitude of the aerodynamic force, signifying the importance of LEV in augmenting force production. Our analysis also shows that forewing-hindwing interaction plays a favorable role in enhancing both lift and thrust production during takeoff.

14 CFR 29.1047 - Takeoff cooling test procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... minutes after the occurence of the highest temperature recorded. (5) The cooling test must be conducted at... takeoff and subsequent climb as follows: (1) Each temperature must be stabilized while hovering in ground...; and (iii) The maximum weight. (2) After the temperatures have stabilized, a climb must be started at...

14 CFR 29.1047 - Takeoff cooling test procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... minutes after the occurance of the highest temperature recorded. (5) The cooling test must be conducted at... takeoff and subsequent climb as follows: (1) Each temperature must be stabilized while hovering in ground...; and (iii) The maximum weight. (2) After the temperatures have stabilized, a climb must be started at...

14 CFR 29.1047 - Takeoff cooling test procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... minutes after the occurance of the highest temperature recorded. (5) The cooling test must be conducted at... takeoff and subsequent climb as follows: (1) Each temperature must be stabilized while hovering in ground...; and (iii) The maximum weight. (2) After the temperatures have stabilized, a climb must be started at...

14 CFR 29.1047 - Takeoff cooling test procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... minutes after the occurence of the highest temperature recorded. (5) The cooling test must be conducted at... takeoff and subsequent climb as follows: (1) Each temperature must be stabilized while hovering in ground...; and (iii) The maximum weight. (2) After the temperatures have stabilized, a climb must be started at...

14 CFR 29.1047 - Takeoff cooling test procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... minutes after the occurence of the highest temperature recorded. (5) The cooling test must be conducted at... takeoff and subsequent climb as follows: (1) Each temperature must be stabilized while hovering in ground...; and (iii) The maximum weight. (2) After the temperatures have stabilized, a climb must be started at...

The Impacts of Rising Temperatures on Aircraft Takeoff Performance

NASA Technical Reports Server (NTRS)

Coffel, Ethan; Thompson, Terence R.; Horton, Radley M.

2017-01-01

Steadily rising mean and extreme temperatures as a result of climate change will likely impact the air transportation system over the coming decades. As air temperatures rise at constant pressure, air density declines, resulting in less lift generation by an aircraft wing at a given airspeed and potentially imposing a weight restriction on departing aircraft. This study presents a general model to project future weight restrictions across a fleet of aircraft with different takeoff weights operating at a variety of airports. We construct performance models for five common commercial aircraft and 19 major airports around the world and use projections of daily temperatures from the CMIP5 model suite under the RCP 4.5 and RCP 8.5 emissions scenarios to calculate required hourly weight restriction. We find that on average, 10 - 30% of annual flights departing at the time of daily maximum temperature may require some weight restriction below their maximum takeoff weights, with mean restrictions ranging from 0.5 to 4% of total aircraft payload and fuel capacity by mid- to late century. Both mid-sized and large aircraft are affected, and airports with short runways and high temperatures, or those at high elevations, will see the largest impacts. Our results suggest that weight restriction may impose a non-trivial cost on airlines and impact aviation operations around the world and that adaptation may be required in aircraft design, airline schedules, and/or runway lengths.

The Impact of Rising Temperatures on Aircraft Takeoff Performance

NASA Astrophysics Data System (ADS)

Coffel, E.; Horton, R. M.; Thompson, T. R.

2017-12-01

Steadily rising mean and extreme temperatures as a result of climate change will likely impact the air transportation system over the coming decades. As air temperatures rise at constant pressure, air density declines, resulting in less lift generation by an aircraft wing at a given airspeed and potentially imposing a weight restriction on departing aircraft. This study presents a general model to project future weight restrictions across a fleet of aircraft with different takeoff weights operating at a variety of airports. We construct performance models for five common commercial aircraft and 19 major airports around the world and use projections of daily temperatures from the CMIP5 model suite under the RCP 4.5 and RCP 8.5 emissions scenarios to calculate required hourly weight restriction. We find that on average, 10-30% of annual flights departing at the time of daily maximum temperature may require some weight restriction below their maximum takeoff weights, with mean restrictions ranging from 0.5 to 4% of total aircraft payload and fuel capacity by mid- to late century. Both mid-sized and large aircraft are affected, and airports with short runways and high tempera- tures, or those at high elevations, will see the largest impacts. Our results suggest that weight restriction may impose a non-trivial cost on airlines and impact aviation operations around the world and that adaptation may be required in aircraft design, airline schedules, and/or runway lengths.

14 CFR 25.115 - Takeoff flight path.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Takeoff flight path. 25.115 Section 25.115... STANDARDS: TRANSPORT CATEGORY AIRPLANES Flight Performance § 25.115 Takeoff flight path. (a) The takeoff flight path shall be considered to begin 35 feet above the takeoff surface at the end of the takeoff...

14 CFR 25.115 - Takeoff flight path.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff flight path. 25.115 Section 25.115... STANDARDS: TRANSPORT CATEGORY AIRPLANES Flight Performance § 25.115 Takeoff flight path. (a) The takeoff flight path shall be considered to begin 35 feet above the takeoff surface at the end of the takeoff...

Optimum take-off angle in the long jump.

PubMed

Linthorne, Nicholas P; Guzman, Maurice S; Bridgett, Lisa A

2005-07-01

In this study, we found that the optimum take-off angle for a long jumper may be predicted by combining the equation for the range of a projectile in free flight with the measured relations between take-off speed, take-off height and take-off angle for the athlete. The prediction method was evaluated using video measurements of three experienced male long jumpers who performed maximum-effort jumps over a wide range of take-off angles. To produce low take-off angles the athletes used a long and fast run-up, whereas higher take-off angles were produced using a progressively shorter and slower run-up. For all three athletes, the take-off speed decreased and the take-off height increased as the athlete jumped with a higher take-off angle. The calculated optimum take-off angles were in good agreement with the athletes' competition take-off angles.

A simplified flight-test method for determining aircraft takeoff performance that includes effects of pilot technique

NASA Technical Reports Server (NTRS)

Larson, T. J.; Schweikhard, W. G.

1974-01-01

A method for evaluating aircraft takeoff performance from brake release to air-phase height that requires fewer tests than conventionally required is evaluated with data for the XB-70 airplane. The method defines the effects of pilot technique on takeoff performance quantitatively, including the decrease in acceleration from drag due to lift. For a given takeoff weight and throttle setting, a single takeoff provides enough data to establish a standardizing relationship for the distance from brake release to any point where velocity is appropriate to rotation. The lower rotation rates penalized takeoff performance in terms of ground roll distance; the lowest observed rotation rate required a ground roll distance that was 19 percent longer than the highest. Rotations at the minimum rate also resulted in lift-off velocities that were approximately 5 knots lower than the highest rotation rate at any given lift-off distance.

A Description of Methodologies Used in Estimation of A-Weighted Sound Levels for FAA Advisory Circular AC-36-3B.

DTIC Science & Technology

1982-01-01

second) Dia propeller diameter (expressed in inches) T°F air temperature in degrees Farenheit T°C air temperature in degrees Celsius T:dBA total dBA...eMpiriC31 function to the absolute noise level ordinate. The term 240 log ( MH is the most sensitive and important part of the equation. The constant (240...standard day, zero wind, dry, zero gradient runway, at a sea level airport. 2. All aircraft operate at maximum takeoff gross weight. 3. All aircraft climb

The Use of a Lidar Forward-Looking Turbulence Sensor for Mixed-Compression Inlet Unstart Avoidance and Gross Weight Reduction on a High Speed Civil Transport

NASA Technical Reports Server (NTRS)

Soreide, David; Bogue, Rodney K.; Ehernberger, L. J.; Seidel, Jonathan

1997-01-01

Inlet unstart causes a disturbance akin to severe turbulence for a supersonic commercial airplane. Consequently, the current goal for the frequency of unstarts is a few times per fleet lifetime. For a mixed-compression inlet, there is a tradeoff between propulsion system efficiency and unstart margin. As the unstart margin decreases, propulsion system efficiency increases, but so does the unstart rate. This paper intends to first, quantify that tradeoff for the High Speed Civil Transport (HSCT) and second, to examine the benefits of using a sensor to detect turbulence ahead of the airplane. When the presence of turbulence is known with sufficient lead time to allow the propulsion system to adjust the unstart margin, then inlet un,starts can be minimized while overall efficiency is maximized. The NASA Airborne Coherent Lidar for Advanced In-Flight Measurements program is developing a lidar system to serve as a prototype of the forward-looking sensor. This paper reports on the progress of this development program and its application to the prevention of inlet unstart in a mixed-compression supersonic inlet. Quantified benefits include significantly reduced takeoff gross weight (TOGW), which could increase payload, reduce direct operating costs, or increase range for the HSCT.

14 CFR 23.53 - Takeoff performance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff performance. 23.53 Section 23.53... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.53 Takeoff performance. (a) For normal, utility, and acrobatic category airplanes, the takeoff distance must be...

14 CFR 23.53 - Takeoff performance.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Takeoff performance. 23.53 Section 23.53... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.53 Takeoff performance. (a) For normal, utility, and acrobatic category airplanes, the takeoff distance must be...

14 CFR 23.53 - Takeoff performance.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff performance. 23.53 Section 23.53... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.53 Takeoff performance. (a) For normal, utility, and acrobatic category airplanes, the takeoff distance must be...

Concept Development of a Mach 1.6 High-Speed Civil Transport

NASA Technical Reports Server (NTRS)

Shields, Elwood W.; Fenbert, James W.; Ozoroski, Lori P.; Geiselhart, Karl A.

1999-01-01

A high-speed civil transport configuration with a Mach number of 1.6 was developed as part of the NASA High-Speed Research Program to serve as a baseline for assessing advanced technologies required for an aircraft with a service entry date of 2005. This configuration offered more favorable solutions to environmental concerns than configurations with higher Mach numbers. The Mach 1.6 configuration was designed for a 6500 n.mi. mission with a 250-passenger payload. The baseline configuration has a wing area of 8732 square feet a takeoff gross weight of 591570 lb, and four 41000-lb advanced turbine bypass engines defined by NASA. These engines have axisymmetric mixer-ejector nozzles that are assumed to yield 20 dB of noise suppression during takeoff, which is assumed to satisfy, the FAR Stage III noise requirements. Any substantial reduction in this assumed level of suppression would require oversizing the engines to meet community noise regulations and would severly impact the gross weight of the aircraft at takeoff. These engines yield a ratio of takeoff thrust to weight of 0.277 and a takeoff wing loading of 67.8 lb/square feet that results in a rotation speed of 169 knots. The approach velocity of the sized configuration at the end of the mission is 131 knots. The baseline configuration was resized with an engine having a projected life of 9000 hr for hot rotating parts and 18000 hr for the rest of the engine, as required for commercial use on an aircraft with a service entry date of 2005. Results show an increase in vehicle takeoff gross weight of approximately 58700 lb. This report presents the details of the configuration development, mass properties, aerodynamic design, propulsion system and integration, mission performance, and sizing.

Escaping blood-fed malaria mosquitoes minimize tactile detection without compromising on take-off speed.

PubMed

Muijres, F T; Chang, S W; van Veen, W G; Spitzen, J; Biemans, B T; Koehl, M A R; Dudley, R

2017-10-15

To escape after taking a blood meal, a mosquito must exert forces sufficiently high to take off when carrying a load roughly equal to its body weight, while simultaneously avoiding detection by minimizing tactile signals exerted on the host's skin. We studied this trade-off between escape speed and stealth in the malaria mosquito Anopheles coluzzii using 3D motion analysis of high-speed stereoscopic videos of mosquito take-offs and aerodynamic modeling. We found that during the push-off phase, mosquitoes enhanced take-off speed using aerodynamic forces generated by the beating wings in addition to leg-based push-off forces, whereby wing forces contributed 61% of the total push-off force. Exchanging leg-derived push-off forces for wing-derived aerodynamic forces allows the animal to reduce peak force production on the host's skin. By slowly extending their long legs throughout the push-off, mosquitoes spread push-off forces over a longer time window than insects with short legs, thereby further reducing peak leg forces. Using this specialized take-off behavior, mosquitoes are capable of reaching take-off speeds comparable to those of similarly sized fruit flies, but with weight-normalized peak leg forces that were only 27% of those of the fruit flies. By limiting peak leg forces, mosquitoes possibly reduce the chance of being detected by the host. The resulting combination of high take-off speed and low tactile signals on the host might help increase the mosquito's success in escaping from blood-hosts, which consequently also increases the chance of transmitting vector-borne diseases, such as malaria, to future hosts. © 2017. Published by The Company of Biologists Ltd.

Takeoff certification considerations for large subsonic and supersonic transport airplanes using the Ames flight simulator for advanced aircraft

NASA Technical Reports Server (NTRS)

Snyder, C. T.; Drinkwater, F. J., III; Fry, E. B.; Forrest, R. D.

1973-01-01

Data for use in development of takeoff airworthiness standards for new aircraft designs such as the supersonic transport (SST) and the large wide-body subsonic jet transport are provided. An advanced motion simulator was used to compare the performance and handling characteristics of three representative large jet transports during specific flight certification tasks. Existing regulatory constraints and methods for determining rotation speed were reviewed, and the effects on takeoff performance of variations in rotation speed, pitch attitude, and pitch attitude rate during the rotation maneuver were analyzed. A limited quantity of refused takeoff information was obtained. The aerodynamics, wing loading, and thrust-to-weight ratio of the subject SST resulted in takeoff speeds limited by climb (rather than lift-off) considerations. Take-off speeds based on U.S. subsonic transport requirements were found unacceptable because of the criticality of rotation-abuse effects on one-engine-inoperative climb performance. Adequate safety margin was provided by takeoff speeds based on proposed Anglo-French supersonic transport (TSS) criteria, with the limiting criterion being that takeoff safety speed be at least 1.15 times the one-engine-inoperative zero-rate-of-climb speed. Various observations related to SST certification are presented.

14 CFR 135.217 - IFR: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false IFR: Takeoff limitations. 135.217 Section 135.217 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.217 IFR: Takeoff limitations. No person may takeoff an...

14 CFR 135.217 - IFR: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false IFR: Takeoff limitations. 135.217 Section 135.217 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.217 IFR: Takeoff limitations. No person may takeoff an...

14 CFR 135.217 - IFR: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false IFR: Takeoff limitations. 135.217 Section 135.217 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.217 IFR: Takeoff limitations. No person may takeoff an...

14 CFR 135.217 - IFR: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false IFR: Takeoff limitations. 135.217 Section 135.217 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.217 IFR: Takeoff limitations. No person may takeoff an...

14 CFR 135.217 - IFR: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false IFR: Takeoff limitations. 135.217 Section 135.217 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Operating Limitations and Weather Requirements § 135.217 IFR: Takeoff limitations. No person may takeoff an...

14 CFR 23.61 - Takeoff flight path.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff flight path. 23.61 Section 23.61... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.61 Takeoff flight path. For each commuter category airplane, the takeoff flight path must be determined as follows...

14 CFR 23.61 - Takeoff flight path.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff flight path. 23.61 Section 23.61... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.61 Takeoff flight path. For each commuter category airplane, the takeoff flight path must be determined as follows...

Methods for predicting unsteady takeoff and landing trajectories of the aircraft

NASA Astrophysics Data System (ADS)

Shevchenko, A.; Pavlov, B.; Nachinkina, G.

2017-01-01

Informational and situational awareness of the aircrew greatly affects the probability of accidents, during takeoff and landing in particular. For the purpose of assessing the current and predicting the future states of an aircraft the energy approach to the flight control is used. Key energy balance equation is generalized to the ground phases. The equation describes the process of accumulating of the total energy of the aircraft along the entire trajectory, including the segment ahead. This segment length is defined by the required terminal energy state. For the takeoff phase the predict algorithm calculates the aircraft position on a runway after which it is possible to accelerate up to the speed of steady level flight and to reach the altitude sufficient for overcoming the high-rise obstacles. For the landing phase the braking distance length is determined. For increasing the likelihood of predicting the correction of the algorithm is introduced. The results of modeling many takeoffs and landings of passenger liner with different weights with the ahead obstacle and the engine failure are given. Working availability of the algorithm correction is shown.

Noise generated by a flight weight, air flow control valve in a vertical takeoff and landing aircraft thrust vectoring system

NASA Technical Reports Server (NTRS)

Huff, Ronald G.

1989-01-01

Tests were conducted in the NASA Lewis Research Center's Powered Lift Facility to experimentally evaluate the noise generated by a flight weight, 12 in. butterfly valve installed in a proposed vertical takeoff and landing thrust vectoring system. Fluctuating pressure measurements were made in the circular duct upstream and downstream of the valve. This data report presents the results of these tests. The maximum overall sound pressure level is generated in the duct downstream of the valve and reached a value of 180 dB at a valve pressure ratio of 2.8. At the higher valve pressure ratios the spectra downstream of the valve is broad banded with its maximum at 1000 Hz.

14 CFR 25.25 - Weight limits.

Code of Federal Regulations, 2014 CFR

2014-01-01

... weights corresponding to the airplane operating conditions (such as ramp, ground or water taxi, takeoff... conditions (such as zero fuel weight, center of gravity position and weight distribution) must be established...

14 CFR 25.25 - Weight limits.

Code of Federal Regulations, 2012 CFR

2012-01-01

... weights corresponding to the airplane operating conditions (such as ramp, ground or water taxi, takeoff... conditions (such as zero fuel weight, center of gravity position and weight distribution) must be established...

14 CFR 25.25 - Weight limits.

Code of Federal Regulations, 2013 CFR

2013-01-01

... weights corresponding to the airplane operating conditions (such as ramp, ground or water taxi, takeoff... conditions (such as zero fuel weight, center of gravity position and weight distribution) must be established...

14 CFR 25.105 - Takeoff.

Code of Federal Regulations, 2010 CFR

2010-01-01

... gradient of climb determined in accordance with § 25.121(b) is greater than one-half of the applicable actual-to-net takeoff flight path gradient reduction defined in § 25.115(b). (b) No takeoff made to... runway gradients. [Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-92, 63 FR 8318, Feb...

Factors affecting measured aircraft sound levels in the vicinity of start-of-takeoff roll

NASA Astrophysics Data System (ADS)

Richard, Horonjeff; Fleming, Gregg G.; Rickley, Edward J.; Connor, Thomas L.

This paper presents the findings of a recently conducted measurement and analysis program of jet transport aircraft sound levels in the vicinity of the star-of-takeoff roll. The purpose of the program was two-fold: (1) to evaluate the computational accuracy of the Federal Aviation Administration's Integrated Noise Model (INM) in the vicinity of start-of-takeoff roll with a recently updated database (INM 3.10), and (2) to provide guidance for future model improvements. Focusing on the second of these two goals, this paper examines several factors affecting Sound Exposure Levels (SELs) in the hemicircular area behind the aircraft brake release point at the start-of-takeoff. In addition to the aircraft type itself, these factors included the geometric relationship of the measurement site to the runway, the wind velocity (speed and direction), aircraft grow weight, and start-of-roll mode (static or rolling start).

Ski jumping takeoff in a wind tunnel with skis.

PubMed

Virmavirta, Mikko; Kivekäs, Juha; Komi, Paavo

2011-11-01

The effect of skis on the force-time characteristics of the simulated ski jumping takeoff was examined in a wind tunnel. Takeoff forces were recorded with a force plate installed under the tunnel floor. Signals from the front and rear parts of the force plate were collected separately to examine the anteroposterior balance of the jumpers during the takeoff. Two ski jumpers performed simulated takeoffs, first without skis in nonwind conditions and in various wind conditions. Thereafter, the same experiments were repeated with skis. The jumpers were able to perform very natural takeoff actions (similar to the actual takeoff) with skis in wind tunnel. According to the subjective feeling of the jumpers, the simulated ski jumping takeoff with skis was even easier to perform than the earlier trials without skis. Skis did not much influence the force levels produced during the takeoff but they still changed the force distribution under the feet. Contribution of the forces produced under the rear part of the feet was emphasized probably because the strong dorsiflexion is needed for lifting the skis to the proper flight position. The results presented in this experiment emphasize that research on ski jumping takeoff can be advanced by using wind tunnels.

Effects of turbine cooling assumptions on performance and sizing of high-speed civil transport

NASA Technical Reports Server (NTRS)

Senick, Paul F.

1992-01-01

The analytical study presented examines the effects of varying turbine cooling assumptions on the performance of a high speed civil transport propulsion system as well as the sizing sensitivity of this aircraft to these performance variations. The propulsion concept employed in this study was a two spool, variable cycle engine with a sea level thrust of 55,000 lbf. The aircraft used for this study was a 250 passenger vehicle with a cruise Mach number of 2.4 and 5000 nautical mile range. The differences in turbine cooling assumptions were represented by varying the amount of high pressure compressor bleed air used to cool the turbines. It was found that as this cooling amount increased, engine size and weight increased, but specific fuel consumption (SFC) decreased at takeoff and climb only. Because most time is spent at cruise, the SFC advantage of the higher bleed engines seen during subsonic flight was minimized and the lower bleed, lighter engines led to the lowest takeoff gross weight vehicles. Finally, the change in aircraft takeoff gross weight versus turbine cooling level is presented.

14 CFR 25.703 - Takeoff warning system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.703 Takeoff... approved range of takeoff positions. (2) Wing spoilers (except lateral control spoilers meeting the...

Comparison of parametric duct-burning turbofan and non-afterburning turbojet engines in a Mach 2.7 transport

NASA Technical Reports Server (NTRS)

Whitlow, J. B., Jr.

1975-01-01

A parametric study was made of duct-burning turbofan and suppressed dry turbojet engines installed in a supersonic transport. A range of fan pressure ratios was considered for the separate-flow-fan engines. The turbofan engines were studied both with and without jet noise suppressors. Single- as well as dual-stream suppression was considered. Attention was concentrated on designs yielding sideline noises of FAR 36 (108 EPNdB) and below. Trades were made between thrust and wing area for a constant takeoff field length. The turbofans produced lower airplane gross weights than the turbojets at FAR 36 and below. The advantage for the turbofans increased as the sideline noise limit was reduced. Jet noise suppression, especially for the duct stream, was very beneficial for the turbofan engines as long as duct burning was permitted during takeoff. The maximum dry unsuppressed takeoff mode, however, yielded better results at extremely low noise levels. Noise levels as low as FAR 36-11 EPNdB were obtained with a turbofan in this takeoff mode, but at a considerable gross weight penalty relative to the best FAR 36 results.

14 CFR 23.53 - Takeoff performance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Takeoff performance. 23.53 Section 23.53... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.53 Takeoff performance. Link to an amendment published at 76 FR 75753, December 2, 2011. (a) For normal, utility, and...

14 CFR 29.63 - Takeoff: Category B.

Code of Federal Regulations, 2011 CFR

2011-01-01

... unfavorable center of gravity. The takeoff may be begun in any manner if— (a) The takeoff surface is defined; (b) Adequate safeguards are maintained to ensure proper center of gravity and control positions; and...

14 CFR 29.63 - Takeoff: Category B.

Code of Federal Regulations, 2010 CFR

2010-01-01

... unfavorable center of gravity. The takeoff may be begun in any manner if— (a) The takeoff surface is defined; (b) Adequate safeguards are maintained to ensure proper center of gravity and control positions; and...

14 CFR 29.63 - Takeoff: Category B.

Code of Federal Regulations, 2012 CFR

2012-01-01

... unfavorable center of gravity. The takeoff may be begun in any manner if— (a) The takeoff surface is defined; (b) Adequate safeguards are maintained to ensure proper center of gravity and control positions; and...

14 CFR 29.63 - Takeoff: Category B.

Code of Federal Regulations, 2013 CFR

2013-01-01

... unfavorable center of gravity. The takeoff may be begun in any manner if— (a) The takeoff surface is defined; (b) Adequate safeguards are maintained to ensure proper center of gravity and control positions; and...

14 CFR 29.63 - Takeoff: Category B.

Code of Federal Regulations, 2014 CFR

2014-01-01

... unfavorable center of gravity. The takeoff may be begun in any manner if— (a) The takeoff surface is defined; (b) Adequate safeguards are maintained to ensure proper center of gravity and control positions; and...

14 CFR Appendix H to Part 36 - Noise Requirements For Helicopters Under Subpart H

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Gross dimensions of aircraft and location of engines. (iii) Aircraft gross weight for each test run. (iv... arithmetic average of the corrected noise measurements for all valid test runs at the takeoff, level flyovers... limit for all valid test runs under section H36.111(d) of this appendix applies separately to the EPNdB...

14 CFR Appendix H to Part 36 - Noise Requirements For Helicopters Under Subpart H

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Gross dimensions of aircraft and location of engines. (iii) Aircraft gross weight for each test run. (iv... arithmetic average of the corrected noise measurements for all valid test runs at the takeoff, level flyovers... limit for all valid test runs under section H36.111(d) of this appendix applies separately to the EPNdB...

14 CFR Appendix H to Part 36 - Noise Requirements For Helicopters Under Subpart H

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Gross dimensions of aircraft and location of engines. (iii) Aircraft gross weight for each test run. (iv... arithmetic average of the corrected noise measurements for all valid test runs at the takeoff, level flyovers... limit for all valid test runs under section H36.111(d) of this appendix applies separately to the EPNdB...

14 CFR Appendix H to Part 36 - Noise Requirements For Helicopters Under Subpart H

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Gross dimensions of aircraft and location of engines. (iii) Aircraft gross weight for each test run. (iv... arithmetic average of the corrected noise measurements for all valid test runs at the takeoff, level flyovers... limit for all valid test runs under section H36.111(d) of this appendix applies separately to the EPNdB...

23 CFR 658.17 - Weight.

Code of Federal Regulations, 2010 CFR

2010-04-01

... maximum gross vehicle weight shall be 80,000 pounds except where lower gross vehicle weight is dictated by... of axles, or a vehicle is 20,000 pounds. (d) The maximum gross weight on tandem axles is 34,000... first and last axle is 36 feet or more. In no case shall the total gross weight of a vehicle exceed 80...

Optimization of engines for a commercial Mach 0.98 transport using advanced turbine cooling methods

NASA Technical Reports Server (NTRS)

Kraft, G. A.; Whitlow, J. B., Jr.

1972-01-01

A study was made of an advanced technology airplane using supercritical aerodynamics. Cruise Mach number was 0.98 at 40,000 feet altitude with a payload of 60,000 pounds and a range of 3000 nautical miles. Separate-flow turbofans were examined parametrically to determine the effect of sea-level-static design turbine-inlet-temperature and noise on takeoff gross weight (TOGW) assuming full-film turbine cooling. The optimum turbine inlet temperature was 2650 F. Two-stage-fan engines, with cruise fan pressure ratio of 2.25, achieved a noise goal of 103.5 EPNdB with todays noise technology while one-stage-fan engines, achieved a noise goal of 98 EPNdB. The take-off gross weight penalty to use the one-stage fan was 6.2 percent.

Effect of body-weight suspension training versus treadmill training on gross motor abilities of children with spastic diplegic cerebral palsy.

PubMed

Emara, Hatem A; El-Gohary, Tarek M; Al-Johany, Ahmed A

2016-06-01

Suspension training and treadmill training are commonly used for promoting functional gross motor skills in children with cerebral palsy. The aim of this study was to compare the effect of body-weight suspension training versus treadmill training on gross motor functional skills. Assessor-blinded, randomized, controlled intervention study. Outpatient rehabilitation facility. Twenty children with spastic diplegia (7 boys and 13 girls) in the age ranged from 6 to 8 years old were randomly allocated into two equal groups. All children were assessed at baseline, after 18-session and after 36-session. During the twelve-week outpatient rehabilitation program, both groups received traditional therapeutic exercises. Additionally, one group received locomotor training using the treadmill while the other group received locomotor training using body-weight suspension through the dynamic spider cage. Assessment included dimensions "D" standing and "E" walking of the gross motor function measure, in addition to the 10-m Walking Test and the five times sit to stand test. Training was applied three times per week for twelve consecutive weeks. No significant difference was found in standing or walking ability for measurements taken at baseline or after 18-session of therapy. Measurements taken at 36-session showed that suspension training achieved significantly (P<0.05) higher average score than treadmill training for dimension D as well as for dimension E. No significant difference was found between suspension training and treadmill training regarding walking speed or sit to stand transitional skills. Body-weight suspension training is effective in improving walking and locomotor capabilities in children with spastic diplegia. After three month suspension training was superior to treadmill training. Body-weight suspension training promotes adequate postural stability, good balance control, and less exertion which facilitates efficient and safe gait.

Parametric Study of a Mach 2.4 Transport Engine with Supersonic Through-Flow Rotor and Supersonic Counter-Rotating Diffuser (SSTR/SSCRD)

NASA Technical Reports Server (NTRS)

Tran, Donald H.

2004-01-01

A parametric study is conducted to evaluate a mixed-flow turbofan equipped with a supersonic through-flow rotor and a supersonic counter-rotating diffuser (SSTR/SSCRD) for a Mach 2.4 civil transport. Engine cycle, weight, and mission analyses are performed to obtain a minimum takeoff gross weight aircraft. With the presence of SSTR/SSCRD, the inlet can be shortened to provide better pressure recovery. For the same engine airflow, the inlet, nacelle, and pylon weights are estimated to be 73 percent lighter than those of a conventional inlet. The fan weight is 31 percent heavier, but overall the installed engine pod weight is 11 percent lighter than the current high-speed civil transport baseline conventional mixed-flow turbofan. The installed specific fuel consumption of the supersonic fan engine is 2 percent higher than that of the baseline turbofan at supersonic cruise. Finally, the optimum SSTR/SSCRD airplane meets the FAR36 Stage 3 noise limit and is within 7 percent of the baseline turbofan airplane takeoff gross weight over a 5000-n mi mission.

A Performance Assessment of Eight Low-Boom High-Speed Civil Transport Concepts

NASA Technical Reports Server (NTRS)

Baize, Daniel G.; McElroy, Marcus O.; Fenbert, James A.; Coen, Peter G.; Ozoroski, Lori P.; Domack, Chris S.; Needleman, Kathy E.; Geiselhart, Karl A.

1999-01-01

A performance assessment of eight low-boom high speed civil transport (HSCT) configurations and a reference HSCT configuration has been performed. Although each of the configurations was designed with different engine concepts, for consistency, a year 2005 technology, 0.4 bypass ratio mixed-flow turbofan (MFTF) engine was used for all of the performance assessments. Therefore, all original configuration nacelles were replaced by a year 2005 MFRF nacelle design which corresponds to the engine deck utilized. The engine thrust level was optimized to minimize vehicle takeoff gross weight. To preserve the configuration's sonic-boom shaping, wing area was not optimized or altered from its original design value. Performance sizings were completed when possible for takeoff balanced field lengths of 11,000 ft and 12,000 ft, not considering FAR Part 36 Stage III noise compliance. Additionally, an arbitrary sizing with thrust-to-weight ratio equal to 0.25 was performed, enabling performance levels to be compared independent of takeoff characteristics. The low-boom configurations analyzed included designs from the Boeing Commercial Airplane Group, Douglas Aircraft Company, Ames Research Center, and Langley Research Center. This paper discusses the technology level assumptions, mission profile, analysis methodologies, and the results of the assessment. The results include maximum lift-to-drag ratios, total fuel consumption, number of passengers, optimum engine sizing plots, takeoff performance, mission block time, and takeoff gross weight for all configurations. Results from the low-boom configurations are also compared with a non-low-boom reference configuration. Configuration dependent advantages or deficiencies are discussed as warranted.

14 CFR 23.61 - Takeoff flight path.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Takeoff flight path. 23.61 Section 23.61... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Performance § 23.61 Takeoff flight path. For normal, utility, and acrobatic category multiengine jets of more than 6,000 pounds...

Supersonic through-flow fan engine and aircraft mission performance

NASA Technical Reports Server (NTRS)

Franciscus, Leo C.; Maldonado, Jaime J.

1989-01-01

A study was made to evaluate potential improvement to a commercial supersonic transport by powering it with supersonic through-flow fan turbofan engines. A Mach 3.2 mission was considered. The three supersonic fan engines considered were designed to operate at bypass ratios of 0.25, 0.5, and 0.75 at supersonic cruise. For comparison a turbine bypass turbojet was included in the study. The engines were evaluated on the basis of aircraft takeoff gross weight with a payload of 250 passengers for a fixed range of 5000 N.MI. The installed specific fuel consumption of the supersonic fan engines was 7 to 8 percent lower than that of the turbine bypass engine. The aircraft powered by the supersonic fan engines had takeoff gross weights 9 to 13 percent lower than aircraft powered by turbine bypass engines.

Aerodynamic performance investigation of advanced mechanical suppressor and ejector nozzle concepts for jet noise reduction

NASA Technical Reports Server (NTRS)

Wagenknecht, C. D.; Bediako, E. D.

1985-01-01

Advanced Supersonic Transport jet noise may be reduced to Federal Air Regulation limits if recommended refinements to a recently developed ejector shroud exhaust system are successfully carried out. A two-part program consisting of a design study and a subscale model wind tunnel test effort conducted to define an acoustically treated ejector shroud exhaust system for supersonic transport application is described. Coannular, 20-chute, and ejector shroud exhaust systems were evaluated. Program results were used in a mission analysis study to determine aircraft takeoff gross weight to perform a nominal design mission, under Federal Aviation Regulation (1969), Part 36, Stage 3 noise constraints. Mission trade study results confirmed that the ejector shroud was the best of the three exhaust systems studied with a significant takeoff gross weight advantage over the 20-chute suppressor nozzle which was the second best.

Prediction of noise constrained optimum takeoff procedures

NASA Technical Reports Server (NTRS)

Padula, S. L.

1980-01-01

An optimization method is used to predict safe, maximum-performance takeoff procedures which satisfy noise constraints at multiple observer locations. The takeoff flight is represented by two-degree-of-freedom dynamical equations with aircraft angle-of-attack and engine power setting as control functions. The engine thrust, mass flow and noise source parameters are assumed to be given functions of the engine power setting and aircraft Mach number. Effective Perceived Noise Levels at the observers are treated as functionals of the control functions. The method is demonstrated by applying it to an Advanced Supersonic Transport aircraft design. The results indicate that automated takeoff procedures (continuously varying controls) can be used to significantly reduce community and certification noise without jeopardizing safety or degrading performance.

Behaviour of coconut mites preceding take-off to passive aerial dispersal.

PubMed

Melo, J W S; Lima, D B; Sabelis, M W; Pallini, A; Gondim, M G C

2014-12-01

For more than three decades the coconut mite Aceria guerreronis Keifer is one of the most important pests of coconut palms and has recently spread to many coconut production areas worldwide. Colonization of coconut palms is thought to arise from mites dispersing aerially after take-off from other plants within the same plantation or other plantations. The underlying dispersal behaviour of the mite at take-off, in the airborne state and after landing is largely unknown and this is essential to understand how they spread from tree to tree. In this article we studied whether take-off to aerial dispersal of coconut mites is preceded by characteristic behaviour, whether there is a correlation between the body position preceding aerial dispersal and the direction of the wind, and whether the substrate (outer surface of coconut bracts or epidermis) and the wind speed matter to the decision to take-off. We found that take-off can sometimes be preceded by a raised body stance, but more frequently take-off occurs while the mite is walking or resting on its substrate. Coconut mites that become airborne assumed a body stance that had no relation to the wind direction. Take-off was suppressed on a substrate providing food to coconut mites, but occurred significantly more frequently on the outer surface of coconut bracts than on the surface of the fruit. For both substrates, take-off frequency increased with wind speed. We conclude that coconut mites have at least some degree of control over take-off for aerial dispersal and that there is as yet no reason to infer that a raised body stance is necessary to become airborne.

The reduction of takeoff ground roll by the application of a nose gear jump strut

NASA Technical Reports Server (NTRS)

Eppel, Joseph C.; Maisel, Martin D.; Mcclain, J. Greer; Luce, W.

1994-01-01

A series of flight tests were conducted to evaluate the reduction of takeoff ground roll distance obtainable from a rapid extension of the nose gear strut. The NASA Quiet Short-haul Research Aircraft (QSRA) used for this investigation is a transport-size short take off and landing (STOL) research vehicle with a slightly swept wing that employs the upper surface blowing (USB) concept to attain the high lift levels required for its low-speed, short-field performance. Minor modifications to the conventional nose gear assembly and the addition of a high-pressure pneumatic system and a control system provided the extendable nose gear, or jump strut, capability. The limited flight test program explored the effects of thrust-to-weight ratio, wing loading, storage tank initial pressure, and control valve open time duration on the ground roll distance. The data show that a reduction of takeoff ground roll on the order of 10 percent was achieved with the use of the jump strut, as predicted. Takeoff performance with the jump strut was also found to be essentially independent of the pneumatic supply pressure and was only slightly affected by control valve open time within the range of the parameters examined.

NATO Standardization and Licensing Policy-Exploratory Phase. Volume 3. Supplement

DTIC Science & Technology

1976-11-30

Aerospatiale will perform at least half the production of this aircraft.* The concept involves a relatively light- weight advanced interceptor with...a ratio of total thrust to takeoff gross weight of about unity. The technology of the aircraft calls for the use of carbon fiber in selected...presenting a system with operating temperatures, pressure ratios, and thrust-to- weight ratios roughly comparable to U.S. technology. The

Effects of Vehicle Weight and True Versus Indicated Airspeed on BVI Noise During Steady Descending Flight

NASA Technical Reports Server (NTRS)

Stephenson, James H.; Greenwood, Eric

2015-01-01

Blade-vortex interaction noise measurements are analyzed for an AS350B helicopter operated at 7000 ft elevation above sea level. Blade-vortex interaction (BVI) noise from four, 6 degree descent conditions are investigated with descents flown at 80 knot true and indicated airspeed, as well as 4400 and 3915 pound take-off weights. BVI noise is extracted from the acquired acoustic signals by way of a previously developed time-frequency analysis technique. The BVI extraction technique is shown to provide a better localization of BVI noise, compared to the standard Fourier transform integration method. Using this technique, it was discovered that large changes in BVI noise amplitude occurred due to changes in vehicle gross weight. Changes in BVI noise amplitude were too large to be due solely to changes in the vortex strength caused by varying vehicle weight. Instead, it is suggested that vehicle weight modifies the tip-path-plane angle of attack, as well as induced inflow, resulting in large variations of BVI noise. It was also shown that defining flight conditions by true airspeed, rather than indicated airspeed, provides more consistent BVI noise signals.

Flight investigation of the use of a nose gear jump strut to reduce takeoff ground roll distance of STOL aircraft

NASA Technical Reports Server (NTRS)

Eppel, Joseph C.; Hardy, Gordon; Martin, James L.

1994-01-01

A series of flight tests was conducted to evaluate the reduction of takeoff ground roll distance obtainable from a rapid extension of the nose gear strut. The NASA Quiet Short-haul Research Aircraft (QSRA) used for this investigation is a transport-size short takeoff and landing (STOL) research vehicle with a slightly swept wing that employs the upper surface blowing (USB) concept to attain the high lift levels required for its low speed, short-field performance. Minor modifications to the conventional nose gear assembly and the addition of a high pressure pneumatic system and a control system provided the extendible nose gear, or 'jump strut,' capability. The limited flight test program explored the effects of thrust-to-weight ratio, storage tank initial pressure, and control valve open time duration on the ground roll distance. The data show that the predicted reduction of takeoff ground roll on the order of 10 percent was achieved with the use of the jump strut. Takeoff performance with the jump strut was also found to be essentially independent of the pneumatic supply pressure and was only slightly affected by control valve open time within the range of the parameters examined.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Lee H., Jr. (Inventor)

1994-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (VR) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Jr., Lee H. (Inventor)

1991-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a predicted nominal performance based upon given conditions, performance deficiencies are detected by the system.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Jr., Lee H. (Inventor)

1996-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

14 CFR 23.66 - Takeoff climb: One-engine inoperative.

Code of Federal Regulations, 2013 CFR

2013-01-01

... applicant with— (a) The critical engine inoperative and its propeller in the position it rapidly and... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Takeoff climb: One-engine inoperative. 23... Performance § 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category...

14 CFR 23.66 - Takeoff climb: One-engine inoperative.

Code of Federal Regulations, 2010 CFR

2010-01-01

... applicant with— (a) The critical engine inoperative and its propeller in the position it rapidly and... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff climb: One-engine inoperative. 23... Performance § 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category...

14 CFR 23.66 - Takeoff climb: One-engine inoperative.

Code of Federal Regulations, 2014 CFR

2014-01-01

... applicant with— (a) The critical engine inoperative and its propeller in the position it rapidly and... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Takeoff climb: One-engine inoperative. 23... Performance § 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category...

14 CFR 23.66 - Takeoff climb: One-engine inoperative.

Code of Federal Regulations, 2012 CFR

2012-01-01

... applicant with— (a) The critical engine inoperative and its propeller in the position it rapidly and... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Takeoff climb: One-engine inoperative. 23... Performance § 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category...

14 CFR 23.66 - Takeoff climb: One-engine inoperative.

Code of Federal Regulations, 2011 CFR

2011-01-01

... applicant with— (a) The critical engine inoperative and its propeller in the position it rapidly and... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff climb: One-engine inoperative. 23... Performance § 23.66 Takeoff climb: One-engine inoperative. For normal, utility, and acrobatic category...

Preliminary Study of Advanced Turboprops for Low Energy Consumption

NASA Technical Reports Server (NTRS)

Kraft, G. A.; Strack, W. C.

1975-01-01

The fuel savings potential of advanced turboprops (operational about 1985) was calculated and compared with that of an advanced turbofan for use in an advanced subsonic transport. At the design point, altitude 10.67 km and Mach 0.80, turbine-inlet temperature was fixed at 1590 K while overall pressure ratio was varied from 25 to 50. The regenerative turboprop had a pressure ratio of only 10 and an 85 percent effective rotary heat exchanger. Variable camber propellers were used with an efficiency of 85 percent. The study indicated a fuel savings of 33 percent, a takeoff gross weight reduction of 15 percent, and a direct operating cost reduction of 18 percent was possible when turboprops were used instead of the reference turbofan at a range of 10 200 km. These reductions were 28, 11, and 14 percent, respectively, at a range of 5500 km. Increasing overall pressure ratio from 25 to 50 saved little fuel and slightly increased takeoff gross weight.

Aerodynamics of a beetle in take-off flights

NASA Astrophysics Data System (ADS)

Lee, Boogeon; Park, Hyungmin; Kim, Sun-Tae

2015-11-01

In the present study, we investigate the aerodynamics of a beetle in its take-off flights based on the three-dimensional kinematics of inner (hindwing) and outer (elytron) wings, and body postures, which are measured with three high-speed cameras at 2000 fps. To track the highly deformable wing motions, we distribute 21 morphological markers and use the modified direct linear transform algorithm for the reconstruction of measured wing motions. To realize different take-off conditions, we consider two types of take-off flights; that is, one is the take-off from a flat ground and the other is from a vertical rod mimicking a branch of a tree. It is first found that the elytron which is flapped passively due to the motion of hindwing also has non-negligible wing-kinematic parameters. With the ground, the flapping amplitude of elytron is reduced and the hindwing changes its flapping angular velocity during up and downstrokes. On the other hand, the angle of attack on the elytron and hindwing increases and decreases, respectively, due to the ground. These changes in the wing motion are critically related to the aerodynamic force generation, which will be discussed in detail. Supported by the grant to Bio-Mimetic Robot Research Center funded by Defense Acquisition Program Administration (UD130070ID).

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 121.189 - Airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Turbine engine powered: Takeoff... OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.189 Airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a...

14 CFR 26.21 - Limit of validity.

Code of Federal Regulations, 2014 CFR

2014-01-01

... inspection results, of high-time airplanes of similar structural design, accounting for differences in... whether the maximum takeoff gross weight is a result of an original type certificate or a later design... certificate issued after January 1, 1958, if a design change approval for which application is made after...

14 CFR 26.21 - Limit of validity.

Code of Federal Regulations, 2013 CFR

2013-01-01

... inspection results, of high-time airplanes of similar structural design, accounting for differences in... whether the maximum takeoff gross weight is a result of an original type certificate or a later design... certificate issued after January 1, 1958, if a design change approval for which application is made after...

14 CFR 26.21 - Limit of validity.

Code of Federal Regulations, 2011 CFR

2011-01-01

... inspection results, of high-time airplanes of similar structural design, accounting for differences in... whether the maximum takeoff gross weight is a result of an original type certificate or a later design... certificate issued after January 1, 1958, if a design change approval for which application is made after...

14 CFR 26.21 - Limit of validity.

Code of Federal Regulations, 2012 CFR

2012-01-01

... inspection results, of high-time airplanes of similar structural design, accounting for differences in... whether the maximum takeoff gross weight is a result of an original type certificate or a later design... certificate issued after January 1, 1958, if a design change approval for which application is made after...

Concept Development of a Mach 2.4 High-Speed Civil Transport

NASA Technical Reports Server (NTRS)

Fenbert, James W.; Ozoroski, Lori P.; Geiselhart, Karl A.; Shields, Elwood W.; McElroy, Marcus O.

1999-01-01

In support of the NASA High-Speed Research Program, a Mach 2.4 high-speed civil transport concept was developed to serve as a baseline for studies to assess advanced technologies required for a feasible year 2005 entry-into-service vehicle. The configuration was designed to carry 251 passengers at Mach 2.4 cruise with a 6500-n.mi. range and operate in the existing world airport structure. The details of the configuration development, aerodynamic design, propulsion system and integration, mass properties, sizing, and mission performance are presented. The baseline configuration has a wing area of 9l00 sq ft and a takeoff gross weight of 614300 lb. The four advanced turbine bypass engines have 39 000 lb thrust with a weight of 9950 lb each, yielding a vehicle takeoff thrust-to-weight ratio of 0.254 and a takeoff wing loading of 67.5 lb/sq ft. The configuration was sized by the 11000-ft takeoff field length requirement and the usable fuel volume limit, which results in a rotation speed of 179 knots and an end-of-mission landing approach velocity of 134 knots.

Spectrum of gross motor function in extremely low birth weight children with cerebral palsy at 18 months of age.

PubMed

Vohr, Betty R; Msall, Michael E; Wilson, Dee; Wright, Linda L; McDonald, Scott; Poole, W Kenneth

2005-07-01

The purpose of this study was to evaluate the relationship between cerebral palsy (CP) diagnoses as measured by the topographic distribution of the tone abnormality with level of function on the Gross Motor Function Classification System (GMFCS) and developmental performance on the Bayley Scales of Infant Development II (BSID-II). It was hypothesized that (1) the greater the number of limbs involved, the higher the GMFCS and the lower the BSID-II Motor Scores and (2) there would be a spectrum of function and skill achievement on the GMFCS and BSID-II Motor Scores for children in each of the CP categories. A multicenter, longitudinal cohort study was conducted of 1860 extremely low birth weight (ELBW) infants who were born between August 1, 1995 and February 1, 1998, and evaluated at 18 to 22 months' corrected age. Children were categorized into impairment groups on the basis of the typography of neurologic findings: spastic quadriplegia, triplegia, diplegia, hemiplegia, monoplegia, hypotonic and/or athetotic CP, other abnormal neurologic findings, and normal. The neurologic category then was compared with GMFCS level and BSID-II Motor Scores. A total of 282 (15.2%) of the 1860 children evaluated had CP. Children with more limbs involved had more abnormal GMFCS levels and lower BSID-II scores, reflecting more severe functional limitations. However, for each CP diagnostic category, there was a spectrum of gross motor functional levels and BSID-II scores. Although more than 1 (26.6%) in 4 of the children with CP had moderate to severe gross motor functional impairment, 1 (27.6%) in 4 had motor functional skills that allowed for ambulation. Given the range of gross motor skill outcomes for specific types of CP, the GMFCS is a better indicator of gross motor functional impairment than the traditional categorization of CP that specifies the number of limbs with neurologic impairment. The neurodevelopmental assessment of young children is optimized by combining a standard

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Wing planform study and final configuration selection

NASA Technical Reports Server (NTRS)

1981-01-01

This report summarizes the Wing Planform Study Task and Final Configuration Selection of the Integrated Application of Active Controls (IAAC) Technology Project within the Energy Efficient Transport Program. Application of Active Controls Technology (ACT) in combination with increased wing span resulted in significant improvements over the Conventional Baseline Configuration (Baseline) and the Initial ACT Configuration previously established. The configurations use the same levels of technology (except for ACT), takeoff gross weight, and payload as the Baseline. The Final ACT Configuration (Model 768-107) incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 45% reduction in horizontal tail sizes), lateral/directional-augmented stability, an angle-of-attack limiter, and wing-load alleviation. Flutter-mode control was not beneficial for this configuration. This resulted in an 890 kg (1960 lb) reduction in airplane takeoff gross weight and a 9.8% improvement in cruise lift/drag. At the Baseline mission range (3590 km) (1938 nmi), this amounts to 10% block fuel reduction. Good takeoff performance at high-altitude airports on a hot day was also achieved. Results of this task strongly indicate that the IAAC Project should proceed with the Final ACT evaluation and begin the required control system development and testing.

14 CFR 135.225 - IFR: Takeoff, approach and landing minimums.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false IFR: Takeoff, approach and landing minimums. 135.225 Section 135.225 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... VFR/IFR Operating Limitations and Weather Requirements § 135.225 IFR: Takeoff, approach and landing...

14 CFR 135.225 - IFR: Takeoff, approach and landing minimums.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false IFR: Takeoff, approach and landing minimums. 135.225 Section 135.225 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... VFR/IFR Operating Limitations and Weather Requirements § 135.225 IFR: Takeoff, approach and landing...

14 CFR 135.225 - IFR: Takeoff, approach and landing minimums.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false IFR: Takeoff, approach and landing minimums. 135.225 Section 135.225 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... VFR/IFR Operating Limitations and Weather Requirements § 135.225 IFR: Takeoff, approach and landing...

Multivariate Analysis, Retrieval, and Storage System (MARS). Volume 6: MARS System - A Sample Problem (Gross Weight of Subsonic Transports)

NASA Technical Reports Server (NTRS)

Hague, D. S.; Woodbury, N. W.

1975-01-01

The Mars system is a tool for rapid prediction of aircraft or engine characteristics based on correlation-regression analysis of past designs stored in the data bases. An example of output obtained from the MARS system, which involves derivation of an expression for gross weight of subsonic transport aircraft in terms of nine independent variables is given. The need is illustrated for careful selection of correlation variables and for continual review of the resulting estimation equations. For Vol. 1, see N76-10089.

High speed propeller performance and noise predictions at takeoff/landing conditions

NASA Technical Reports Server (NTRS)

Nallasamy, M.; Woodward, R. P.; Groeneweg, J. F.

1988-01-01

The performance and noise of a high speed SR-7A model propeller under takeoff/landing conditions are considered. The blade loading distributions are obtained by solving the three-dimensional Euler equations and the sound pressure levels are computed using a time domain approach. At the nominal takeoff operating point, the blade sections near the hub are lightly or negatively loaded. The chordwise loading distributions are distinctly different from those of cruise conditions. The noise of the SR-7A model propeller at takeoff is dominated by the loading noise, similar to that at cruise conditions. The waveforms of the acoustic pressure signature are nearly sinusoidal in the plane of the propeller. The computed directivity of the blade passing frequency tone agrees fairly well with the data at nominal takeoff blade angle.

High speed propeller performance and noise predictions at takeoff/landing conditions

NASA Technical Reports Server (NTRS)

Nallasamy, M.; Woodward, R. P.; Groeneweg, J. F.

1987-01-01

The performance and noise of a high speed SR-7A model propeller under takeoff/landing conditions are considered. The blade loading distributions are obtained by solving the three-dimensional Euler equations and the sound pressure levels are computed using a time domain approach. At the nominal takeoff operating point, the blade sections near the hub are lightly or negatively loaded. The chordwise loading distributions are distinctly different from those of cruise conditions. The noise of the SR-7A model propeller at takeoff is dominated by the loading noise, similar to that at cruise conditions. The waveforms of the acoustic pressure signature are nearly sinusoidal in the plane of the propeller. The computed directivity of the blade passing frequency tone agrees fairly well with the data at nominal takeoff blade angle.

14 CFR 121.651 - Takeoff and landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Takeoff and landing weather minimums: IFR... Flight Release Rules § 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. (a) Notwithstanding any clearance from ATC, no pilot may begin a takeoff in an airplane under IFR when the weather...

14 CFR 121.651 - Takeoff and landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Takeoff and landing weather minimums: IFR... Flight Release Rules § 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. (a) Notwithstanding any clearance from ATC, no pilot may begin a takeoff in an airplane under IFR when the weather...

14 CFR 121.651 - Takeoff and landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Takeoff and landing weather minimums: IFR... Flight Release Rules § 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. (a) Notwithstanding any clearance from ATC, no pilot may begin a takeoff in an airplane under IFR when the weather...

14 CFR 121.651 - Takeoff and landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Takeoff and landing weather minimums: IFR... Flight Release Rules § 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. (a) Notwithstanding any clearance from ATC, no pilot may begin a takeoff in an airplane under IFR when the weather...

14 CFR 121.651 - Takeoff and landing weather minimums: IFR: All certificate holders.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Takeoff and landing weather minimums: IFR... Flight Release Rules § 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. (a) Notwithstanding any clearance from ATC, no pilot may begin a takeoff in an airplane under IFR when the weather...

14 CFR 25.904 - Automatic takeoff thrust control system (ATTCS).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Automatic takeoff thrust control system... Automatic takeoff thrust control system (ATTCS). Each applicant seeking approval for installation of an engine power control system that automatically resets the power or thrust on the operating engine(s) when...

14 CFR 25.904 - Automatic takeoff thrust control system (ATTCS).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Automatic takeoff thrust control system... Automatic takeoff thrust control system (ATTCS). Each applicant seeking approval for installation of an engine power control system that automatically resets the power or thrust on the operating engine(s) when...

14 CFR 125.381 - Takeoff and landing weather minimums: IFR.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Takeoff and landing weather minimums: IFR... § 125.381 Takeoff and landing weather minimums: IFR. (a) Regardless of any clearance from ATC, if the reported weather conditions are less than that specified in the certificate holder's operations...

14 CFR 125.381 - Takeoff and landing weather minimums: IFR.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Takeoff and landing weather minimums: IFR... § 125.381 Takeoff and landing weather minimums: IFR. (a) Regardless of any clearance from ATC, if the reported weather conditions are less than that specified in the certificate holder's operations...

14 CFR 125.381 - Takeoff and landing weather minimums: IFR.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Takeoff and landing weather minimums: IFR... § 125.381 Takeoff and landing weather minimums: IFR. (a) Regardless of any clearance from ATC, if the reported weather conditions are less than that specified in the certificate holder's operations...

14 CFR 125.381 - Takeoff and landing weather minimums: IFR.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Takeoff and landing weather minimums: IFR... § 125.381 Takeoff and landing weather minimums: IFR. (a) Regardless of any clearance from ATC, if the reported weather conditions are less than that specified in the certificate holder's operations...

14 CFR 125.381 - Takeoff and landing weather minimums: IFR.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Takeoff and landing weather minimums: IFR... § 125.381 Takeoff and landing weather minimums: IFR. (a) Regardless of any clearance from ATC, if the reported weather conditions are less than that specified in the certificate holder's operations...

How Insects Initiate Flight: Computational Analysis of a Damselfly in Takeoff Flight

NASA Astrophysics Data System (ADS)

Bode-Oke, Ayodeji; Zeyghami, Samane; Dong, Haibo; Flow Simulation Research Group Team

2017-11-01

Flight initiation is essential for survival in biological fliers and can be classified into jumping and non-jumping takeoffs. During jumping takeoffs, the legs generate most of the initial impulse. Whereas the wings generate most of the forces in non-jumping takeoffs, which are usually voluntary, slow, and stable. It is of interest to understand how non-jumping takeoffs occur and what strategies insects use to generate the required forces. Using a high fidelity computational fluid dynamics simulation, we identify the flow features and compute the wing aerodynamic forces to elucidate how flight forces are generated by a damselfly performing a non-jumping takeoff. Our results show that a damselfly generates about three times its bodyweight during the first half-stroke for liftoff while flapping through a steeply inclined stroke plane and slicing the air at high angles of attack. Consequently, a Leading Edge Vortex (LEV) is formed during both the downstroke and upstroke on all the four wings. The formation of the LEV, however, is inhibited in the subsequent upstrokes following takeoff. Accordingly, we observe a drastic reduction in the magnitude of the aerodynamic force, signifying the importance of LEV in augmenting force production. This work was supported by National Science Foundation [CBET-1313217] and Air Force Research Laboratory [FA9550-12-1-007].

14 CFR 25.531 - Hull and main float takeoff condition.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.531 Hull and main float takeoff condition. For the wing and its attachment to the hull or main float— (a) The aerodynamic...

14 CFR 23.531 - Hull and main float takeoff condition.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 23.531 Section 23.531 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... Water Loads § 23.531 Hull and main float takeoff condition. For the wing and its attachment to the hull...

Dancers with achilles tendinopathy demonstrate altered lower extremity takeoff kinematics.

PubMed

Kulig, Kornelia; Loudon, Janice K; Popovich, John M; Pollard, Christine D; Winder, Brooke R

2011-08-01

Controlled laboratory study using a cross-sectional design. To analyze lower extremity kinematics during takeoff of a "saut de chat" (leap) in dancers with and without a history of Achilles tendinopathy (AT). We hypothesized that dancers with AT would demonstrate different kinematic strategies compared to dancers without pathology, and that these differences would be prominent in the transverse and frontal planes. AT is a common injury experienced by dancers. Dance leaps such as the saut de chat place a large demand on the Achilles tendon. Sixteen female dancers with and without a history of AT (mean ± SD age, 18.8 ± 1.2 years) participated. Three-dimensional kinematics at the hip, knee, and ankle were quantified for the takeoff of the saut de chat, using a motion analysis system. A force platform was used to determine braking and push-off phases of takeoff. Peak sagittal, frontal, and transverse plane joint positions during the braking and push-off phases of the takeoff were examined statistically. Independent samples t tests were used to evaluate group differences (α = .05). The dancers in the tendinopathy group demonstrated significantly higher peak hip adduction during the braking phase of takeoff (mean ± SD, 13.5° ± 6.1° versus 7.7° ± 4.2°; P = .046). During the push-off phase, dancers with AT demonstrated significantly more internal rotation at the knee (13.2° ± 5.2° versus 6.9° ± 4.9°; P = .024). Dancers with AT demonstrate increased peak transverse and frontal plane kinematics when performing the takeoff of a saut de chat. These larger displacements may be either causative or compensatory factors in the development of AT.

14 CFR 25.111 - Takeoff path.

Code of Federal Regulations, 2011 CFR

2011-01-01

... gear retraction may not be begun until the airplane is airborne. (c) During the takeoff path... changed, except for gear retraction and automatic propeller feathering, and no change in power or thrust...

14 CFR 25.111 - Takeoff path.

Code of Federal Regulations, 2014 CFR

2014-01-01

... gear retraction may not be begun until the airplane is airborne. (c) During the takeoff path... changed, except for gear retraction and automatic propeller feathering, and no change in power or thrust...

14 CFR 25.111 - Takeoff path.

Code of Federal Regulations, 2010 CFR

2010-01-01

... gear retraction may not be begun until the airplane is airborne. (c) During the takeoff path... changed, except for gear retraction and automatic propeller feathering, and no change in power or thrust...

14 CFR 25.111 - Takeoff path.

Code of Federal Regulations, 2012 CFR

2012-01-01

... gear retraction may not be begun until the airplane is airborne. (c) During the takeoff path... changed, except for gear retraction and automatic propeller feathering, and no change in power or thrust...

14 CFR 25.111 - Takeoff path.

Code of Federal Regulations, 2013 CFR

2013-01-01

... gear retraction may not be begun until the airplane is airborne. (c) During the takeoff path... changed, except for gear retraction and automatic propeller feathering, and no change in power or thrust...

14 CFR 23.57 - Takeoff path.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., landing gear retraction must not be initiated until the airplane is airborne. (c) During the takeoff path... three-engine airplanes; (iii) 1.7 percent for four-engine airplanes; and (4) Except for gear retraction...

Multiple-Purpose Subsonic Naval Aircraft (MPSNA) Multiple Application Propfan Study (MAPS)

NASA Technical Reports Server (NTRS)

Winkeljohn, D. M.; Mayrand, C. H.

1986-01-01

A conceptual design study compared a selected propfan-powered aircraft to a turbofan-powered aircraft for multiple Navy carrier-based support missions in the 1995 timeframe. Conventional takeoff and landing (CTOL) propfan and turbofan-powered designs and short takeoff/vertical landing (STOVL) propfan-powered designs are presented. Ten support mission profiles were defined and the aircraft were sized to be able to perform all ten missions. Emphasis was placed on efficient high altitude loiter for Airborne Early Warning (AEW) and low altitude high speed capability for various offensive and tactical support missions. The results of the study show that the propfan-powered designs have lighter gross weights, lower fuel fractions, and equal or greater performance capability than the turbofan-powered designs. Various sensitives were developed in the study, including the effect of using single-rotation versus counter-rotation propfans and the effect of AEW loiter altitude on vehicle gross weight and empty weight. A propfan technology development plan was presented which illustrates that the development of key components can be achieved without accelerated schedules through the extension of current and planned government and civil propfan programs.

77 FR 9169 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-16

... on 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex... (GPS) Y RWY 20, Amdt 1B Cambridge, MN, Cambridge Muni, Takeoff Minimums and Obstacle DP, Orig Pipestone, MN, Pipestone Muni, NDB RWY 36, Amdt 7, CANCELLED Rushford, MN, Rushford Muni, Takeoff Minimums and...

76 FR 52239 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-22

... Minimums & Obstacle DP, Orig-A Red Oak, IA, Red Oak Muni, Takeoff Minimums & Obstacle DP, Amdt 3 Storm Lake, IA, Storm Lake Muni, Takeoff Minimums & Obstacle DP, Orig Dwight, IL, Dwight, Takeoff Minimums..., Florence Rgnl, RNAV (GPS) RWY 9, Orig-A Spearfish, SD, Black Hills-Clydes Ice Field, RNAV (GPS) RWY 13...

A Conceptual Design of a Short Takeoff and Landing Regional Jet Airliner

NASA Technical Reports Server (NTRS)

Hahn, Andrew S.

2010-01-01

Most jet airliner conceptual designs adhere to conventional takeoff and landing performance. Given this predominance, takeoff and landing performance has not been critical, since it has not been an active constraint in the design. Given that the demand for air travel is projected to increase dramatically, there is interest in operational concepts, such as Metroplex operations that seek to unload the major hub airports by using underutilized surrounding regional airports, as well as using underutilized runways at the major hub airports. Both of these operations require shorter takeoff and landing performance than is currently available for airliners of approximately 100-passenger capacity. This study examines the issues of modeling performance in this now critical flight regime as well as the impact of progressively reducing takeoff and landing field length requirements on the aircraft s characteristics.

14 CFR 91.605 - Transport category civil airplane weight limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Transport category civil airplane weight... civil airplane weight limitations. (a) No person may take off any transport category airplane (other than a turbine-engine-powered airplane certificated after September 30, 1958) unless— (1) The takeoff...

14 CFR 91.605 - Transport category civil airplane weight limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Transport category civil airplane weight... civil airplane weight limitations. (a) No person may take off any transport category airplane (other than a turbine-engine-powered airplane certificated after September 30, 1958) unless— (1) The takeoff...

14 CFR 91.605 - Transport category civil airplane weight limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Transport category civil airplane weight... civil airplane weight limitations. (a) No person may take off any transport category airplane (other than a turbine-engine-powered airplane certificated after September 30, 1958) unless— (1) The takeoff...

14 CFR 23.523 - Design weights and center of gravity positions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Design weights and center of gravity... Structure Water Loads § 23.523 Design weights and center of gravity positions. (a) Design weights. The water... water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of...

14 CFR 23.523 - Design weights and center of gravity positions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Design weights and center of gravity... Structure Water Loads § 23.523 Design weights and center of gravity positions. (a) Design weights. The water... water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of...

14 CFR 23.523 - Design weights and center of gravity positions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Design weights and center of gravity... Structure Water Loads § 23.523 Design weights and center of gravity positions. (a) Design weights. The water... water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of...

14 CFR 23.523 - Design weights and center of gravity positions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Design weights and center of gravity... Structure Water Loads § 23.523 Design weights and center of gravity positions. (a) Design weights. The water... water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of...

14 CFR 23.523 - Design weights and center of gravity positions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Design weights and center of gravity... Structure Water Loads § 23.523 Design weights and center of gravity positions. (a) Design weights. The water... water taxi and takeoff run) must be used. (b) Center of gravity positions. The critical centers of...

76 FR 28171 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-16

...-Clyde Ice Field, Takeoff Minimum and Obstacle DP, Amdt 1 Gladewater, TX, Gladewater Muni, Takeoff... Field, VOR/DME RWY 12, Amdt 4 Devil's Lake, ND, Devil's Lake Rgnl, ILS OR LOC/DME RWY 31, Amdt 2 Devil's Lake, ND, Devil's Lake Rgnl, RNAV (GPS) RWY 3, Amdt 1 Ely, NV, Ely Airport-Yelland Field, Takeoff...

Comparison of the take-off ground reaction force patterns of the pole vault and the long jump.

PubMed

Plessa, E I; Rousanoglou, E N; Boudolos, K D

2010-12-01

The take-off is probably the most important phase of the pole vault. The kinematics of pole vault take-off is often described in comparison to the long jump take-off. If a kinetic similarity were also evidenced, the extra loading of carrying the pole could be avoided by using the long jump style take-off drills in pole vault take-off training. However, to our knowledge, a direct comparison of the take-off ground reaction force (GRF) pattern of the two types of jump has not been reported in the scientific or coaching literature. The purpose of this study was to compare the take-off GRF patterns of the support leg in the pole vault and the long jump. Twelve elite women jumpers undertook pole vault and long jump trials. The take-off GRF patterns were recorded by a force plate (Kistler-9286AA). Temporal and force parameters were determined for all three GRF components. Trials were videotaped to determine the take-off kinematics. Paired sample t-tests (SPSS 13.0) were applied (P≤0.05) for comparison between jumps. No significant differences were found in kinematics (P>0.05). Overall, the GRF patterns were similar, although there were particular significant (P≤0.05) differences in contact times, impulses and force peaks. This study provides scientific support for potential use of the long jump take-off drills during technical preparation for the pole vault take-off.

78 FR 48800 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-12

... 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and..., Takeoff Minimums and Obstacle DP, Amdt 2 Perham, MN, Perham Muni, RNAV (GPS) RWY 13, Orig Perham, MN, Perham Muni, RNAV (GPS) RWY 31, Amdt 1 Perham, MN, Perham Muni, Takeoff Minimums and Obstacle DP, Amdt 1...

Assessment of loaded squat jump height with a free-weight barbell and Smith machine: comparison of the take-off velocity and flight time procedures.

PubMed

Pérez-Castilla, Alejandro; McMahon, John J; Comfort, Paul; García-Ramos, Amador

2017-07-31

The aims of this study were to compare the reliability and magnitude of jump height between the two standard procedures of analysing force platform data to estimate jump height (take-off velocity [TOV] and flight time [FT]) in the loaded squat jump (SJ) exercise performed with a free-weight barbell and in a Smith machine. Twenty-three collegiate men (age 23.1 ± 3.2 years, body mass 74.7 ± 7.3 kg, height 177.1 ± 7.0 cm) were tested twice for each SJ type (free-weight barbell and Smith machine) with 17, 30, 45, 60, and 75 kg loads. No substantial differences in reliability were observed between the TOV (Coefficient of variation [CV]: 9.88%; Intraclass correlation coefficient [ICC]: 0.82) and FT (CV: 8.68%; ICC: 0.88) procedures (CV ratio: 1.14), while the Smith SJ (CV: 7.74%; ICC: 0.87) revealed a higher reliability than the free-weight SJ (CV: 9.88%; ICC: 0.81) (CV ratio: 1.28). The TOV procedure provided higher magnitudes of jump height than the FT procedure for the loaded Smith machine SJ (systematic bias: 2.64 cm; P<0.05), while no significant differences between the TOV and FT procedures were observed in the free-weight SJ exercise (systematic bias: 0.26 cm; P>0.05). Heteroscedasticity of the errors was observed for the Smith machine SJ (r: 0.177) with increasing differences in favour of the TOV procedure for the trials with lower jump height (i.e. higher external loads). Based on these results the use of a Smith machine in conjunction with the FT more accurately determine jump height during the loaded SJ.

Magnetic levitation assisted aircraft take-off and landing (feasibility study - GABRIEL concept)

NASA Astrophysics Data System (ADS)

Rohacs, Daniel; Rohacs, Jozsef

2016-08-01

The Technology Roadmap 2013 developed by the International Air Transport Association envisions the option of flying without an undercarriage to be in operation by 2032. Preliminary investigations clearly indicate that magnetic levitation technology (MagLev) might be an appealing solution to assist the aircraft take-off and landing. The EU supported research project, abbreviated as GABRIEL, was dealing with (i) the concept development, (ii) the identification, evaluation and selection of the deployable magnetic levitation technology, (iii) the definition of the core system elements (including the required aircraft modifications, the ground-based system and airport elements, and the rendezvous control system), (iv) the analysis of the safety and security aspects, (v) the concept validation and (vi) the estimation of the proposed concept impact in terms of aircraft weight, noise, emission, cost-benefit). All results introduced here are compared to a medium size hypothetic passenger aircraft (identical with an Airbus A320). This paper gives a systematic overview of (i) the applied methods, (ii) the investigation of the possible use of magnetic levitation technology to assist the commercial aircraft take-off and landing processes and (iii) the demonstrations, validations showing the feasibility of the radically new concept. All major results are outlined.

Ski jump takeoff performance predictions for a mixed-flow, remote-lift STOVL aircraft

NASA Technical Reports Server (NTRS)

Birckelbaw, Lourdes G.

1992-01-01

A ski jump model was developed to predict ski jump takeoff performance for a short takeoff and vertical landing (STOVL) aircraft. The objective was to verify the model with results from a piloted simulation of a mixed flow, remote lift STOVL aircraft. The prediction model is discussed. The predicted results are compared with the piloted simulation results. The ski jump model can be utilized for basic research of other thrust vectoring STOVL aircraft performing a ski jump takeoff.

14 CFR 23.703 - Takeoff warning system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.703 Takeoff warning system. For commuter category airplanes, unless it can be shown...

14 CFR 23.703 - Takeoff warning system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.703 Takeoff warning system. For commuter category airplanes, unless it can be shown...

Comparative Analysis of the Tour Jete and Aerial with Detailed Analysis of Aerial Takeoff Mechanics

NASA Astrophysics Data System (ADS)

Pierson, Mimi; Coplin, Kim

2006-10-01

Whether internally as muscle tension or from external sources, forces are necessary for all motion. This research focused on athletic rotations where conditions of flight are established during takeoff. By studying reaction forces that produce torques, moments of inertia, and linear and angular differences between distinct rotations around different principle axes of the body (tour jete in ballet - longitudinal axis; aerial in gymnastics - anteroposterior axis), and by looking at the values of angular momentum in the specific mechanics of aerial takeoff, we can gain insight into possible causes of injury, flaws in technique and limitations of athletes. Results showed significant differences in the horizontal and vertical components of takeoff between the tour jete and the aerial, and a realization that torque was produced in different biomechanical planes. Both rotations showed braking forces before takeoff to counteract forward momentum and increase vertical lift, but the angle of applied force varied, and the horizontal components of velocity and force and vertical velocity as well as moment of inertia throughout flight were consistently greater for the aerial. Breakdown of aerial takeoff highlighted the relative importance of the takeoff phases, showing that completion depends fundamentally upon the rotation of the rear foot and torso twisting during takeoff rather than the last foot in contact with the ground.

Lower Extremity Kinematics Differed Between a Controlled Drop-Jump and Volleyball-Takeoffs.

PubMed

Beardt, Bradley S; McCollum, Myranda R; Hinshaw, Taylour J; Layer, Jacob S; Wilson, Margaret A; Zhu, Qin; Dai, Boyi

2018-04-03

Previous studies utilizing jump-landing biomechanics to predict anterior cruciate ligament injuries have shown inconsistent findings. The purpose of this study was to quantify the differences and correlations in jump-landing kinematics between a drop-jump, a controlled volleyball-takeoff, and a simulated-game volleyball-takeoff. Seventeen female volleyball players performed these three tasks on a volleyball court while three-dimensional kinematic data were collected by three calibrated camcorders. Participants demonstrated significantly increased jump height, shorter stance time, increased time differences in initial contact between two feet, increased knee and hip flexion at initial contact and decreased peak knee and hip flexion for both left and right legs, and decreased knee-ankle distance ratio at the lowest height of mid-hip for the two volleyball-takeoffs compared with the drop-jump (p < 0.05, Cohen's dz ≥ 0.8). Significant correlations were observed for all variables between the two volleyball-takeoffs (p < 0.05, ρ ≥ 0.6), but were not for most variables between the drop-jump and two volleyball-takeoffs. Controlled drop-jump kinematics may not represent jump-landing kinematics exhibited during volleyball competition. Jump-landing mechanics during sports-specific tasks may better represent those exhibited during sports competition and their associated risk of ACL injury compared with the drop-jump.

23 CFR 658.17 - Weight.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the bridge formula. (c) The maximum gross weight upon any one axle, including any one axle of a group... following formula, referred to as the Bridge Gross Weight Formula: EC14OC91.012 except that two consecutive... derived from the Bridge Formula, up to a maximum of 80,000 pounds, including all enforcement tolerances...

23 CFR 658.17 - Weight.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the bridge formula. (c) The maximum gross weight upon any one axle, including any one axle of a group... following formula, referred to as the Bridge Gross Weight Formula: EC14OC91.012 except that two consecutive... derived from the Bridge Formula, up to a maximum of 80,000 pounds, including all enforcement tolerances...

14 CFR 23.703 - Takeoff warning system.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Control Systems § 23.703 Takeoff warning system. Link to an amendment published at 76 FR 75757, December 2...

14 CFR 25.107 - Takeoff speeds.

Code of Federal Regulations, 2013 CFR

2013-01-01

...., applying brakes, reducing thrust, deploying speed brakes) to stop the airplane during accelerate-stop tests... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Takeoff speeds. 25.107 Section 25.107 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS...

14 CFR 25.107 - Takeoff speeds.

Code of Federal Regulations, 2014 CFR

2014-01-01

...., applying brakes, reducing thrust, deploying speed brakes) to stop the airplane during accelerate-stop tests... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Takeoff speeds. 25.107 Section 25.107 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS...

14 CFR 25.107 - Takeoff speeds.

Code of Federal Regulations, 2011 CFR

2011-01-01

...., applying brakes, reducing thrust, deploying speed brakes) to stop the airplane during accelerate-stop tests... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff speeds. 25.107 Section 25.107 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS...

14 CFR 25.107 - Takeoff speeds.

Code of Federal Regulations, 2012 CFR

2012-01-01

...., applying brakes, reducing thrust, deploying speed brakes) to stop the airplane during accelerate-stop tests... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Takeoff speeds. 25.107 Section 25.107 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS...

14 CFR 25.107 - Takeoff speeds.

Code of Federal Regulations, 2010 CFR

2010-01-01

...., applying brakes, reducing thrust, deploying speed brakes) to stop the airplane during accelerate-stop tests... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff speeds. 25.107 Section 25.107 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS...

Gross Motor Development in Children Aged 3-5 Years, United States 2012.

PubMed

Kit, Brian K; Akinbami, Lara J; Isfahani, Neda Sarafrazi; Ulrich, Dale A

2017-07-01

Objective Gross motor development in early childhood is important in fostering greater interaction with the environment. The purpose of this study is to describe gross motor skills among US children aged 3-5 years using the Test of Gross Motor Development (TGMD-2). Methods We used 2012 NHANES National Youth Fitness Survey (NNYFS) data, which included TGMD-2 scores obtained according to an established protocol. Outcome measures included locomotor and object control raw and age-standardized scores. Means and standard errors were calculated for demographic and weight status with SUDAAN using sample weights to calculate nationally representative estimates, and survey design variables to account for the complex sampling methods. Results The sample included 339 children aged 3-5 years. As expected, locomotor and object control raw scores increased with age. Overall mean standardized scores for locomotor and object control were similar to the mean value previously determined using a normative sample. Girls had a higher mean locomotor, but not mean object control, standardized score than boys (p < 0.05). However, the mean locomotor standardized scores for both boys and girls fell into the range categorized as "average." There were no other differences by age, race/Hispanic origin, weight status, or income in either of the subtest standardized scores (p > 0.05). Conclusions In a nationally representative sample of US children aged 3-5 years, TGMD-2 mean locomotor and object control standardized scores were similar to the established mean. These results suggest that standardized gross motor development among young children generally did not differ by demographic or weight status.

Ground reaction forces and knee mechanics in the weight acceptance phase of a dance leap take-off and landing.

PubMed

Kulig, Kornelia; Fietzer, Abbigail L; Popovich, John M

2011-01-01

Aesthetic constraints allow dancers fewer technique modifications than other athletes to negotiate the demands of leaping. We examined vertical ground reaction force and knee mechanics during a saut de chat performed by healthy dancers. It was hypothesized that vertical ground reaction force during landing would exceed that of take-off, resulting in greater knee extensor moments and greater knee angular stiffness. Twelve dancers (six males, six females; age 18.9 ± 1.2 years, mass 59.2 ± 9.5 kg, height 1.68 ± 0.08 m, dance training 8.9 ± 5.1 years) with no history of low back pain or lower extremity pathology participated in the study. Saut de chat data were captured using an eight-camera Vicon system and AMTI force platforms. Peak ground reaction force was 26% greater during the landing phase, but did not result in increased peak knee extensor moments. Taking into account the 67% greater knee angular displacement during landing, this resulted in less knee angular stiffness during landing. In conclusion, landing was accomplished with less knee angular stiffness despite the greater peak ground reaction force. A link between decreased joint angular stiffness and increased soft tissue injury risk has been proposed elsewhere; therefore, landing from a saut de chat may be more injurious to the knee soft tissue than take-off.

A class 2 weight assessment for the implementation of commonality and preliminary structural designs for the family of commuter airplanes

NASA Technical Reports Server (NTRS)

Creighton, Tom; Dragush, George; Hendrich, Louis; Hensley, Doug; Morgan, Louise; Oxendine, Charles; Remen, John; Robinson, Terry; Russell, Mark; Swift, Jerry

1987-01-01

The feasibility of commonality objectives are determined. Commonality is discussed in terms of weight penalties that increase the take-off weight of several members of the family of airplanes. Preliminary designs of fuselage structural members and a discussion of weight penalties due to implementation of common fuselage structure throughout the family is examined. Wing torque box designs are discussed along with structural weight penalties incurred. A landing gear design study is contained along with the weight penalties that a common gear system will impose. Implementation of common power plants throughout the family and the weight penalties that occur are discussed. The weight penalties imposed by commonality on all the airplanes in the family are summarized. Class 2 breakdowns are also presented. The feasibility of commonality based on a percentage of take-off weight increase over the Class 2 baseline weights is then assessed.

Supersonic fan engines for military aircraft

NASA Technical Reports Server (NTRS)

Franciscus, L. C.

1983-01-01

Engine performance and mission studies were performed for turbofan engines with supersonic through-flow fans. A Mach 2.4 CTOL aircraft was used in the study. Two missions were considered: a long range penetrator mission and a long range intercept mission. The supersonic fan engine is compared with an augmented mixed flow turbofan in terms of mission radius for a fixed takeoff gross weight of 75,000 lbm. The mission radius of aircraft powered by supersonic fan engines could be 15 percent longer than aircraft powered with conventional turbofan engines at moderate thrust to gross weight ratios. The climb and acceleration performance of the supersonic fan engines is better than that of the conventional turbofan engines.

14 CFR 121.649 - Takeoff and landing weather minimums: VFR: Domestic operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Takeoff and landing weather minimums: VFR... Flight Release Rules § 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. (a) Except... weather minimums in this section do not apply to the VFR operation of fixed-wing aircraft at any of the...

14 CFR 121.649 - Takeoff and landing weather minimums: VFR: Domestic operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Takeoff and landing weather minimums: VFR... Flight Release Rules § 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. (a) Except... weather minimums in this section do not apply to the VFR operation of fixed-wing aircraft at any of the...

14 CFR 121.649 - Takeoff and landing weather minimums: VFR: Domestic operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Takeoff and landing weather minimums: VFR... Flight Release Rules § 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. (a) Except... weather minimums in this section do not apply to the VFR operation of fixed-wing aircraft at any of the...

14 CFR 121.649 - Takeoff and landing weather minimums: VFR: Domestic operations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Takeoff and landing weather minimums: VFR... Flight Release Rules § 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. (a) Except... weather minimums in this section do not apply to the VFR operation of fixed-wing aircraft at any of the...

14 CFR 121.649 - Takeoff and landing weather minimums: VFR: Domestic operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Takeoff and landing weather minimums: VFR... Flight Release Rules § 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. (a) Except... weather minimums in this section do not apply to the VFR operation of fixed-wing aircraft at any of the...

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... engine powered: Takeoff limitations. 135.379 Section 135.379 Aeronautics and Space FEDERAL AVIATION... category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine... existing at take- off. (b) No person operating a turbine engine powered large transport category airplane...

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... engine powered: Takeoff limitations. 135.379 Section 135.379 Aeronautics and Space FEDERAL AVIATION... category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine... existing at take- off. (b) No person operating a turbine engine powered large transport category airplane...

75 FR 76626 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-09

..., Norman County Ada/Twin Valley, Takeoff Minimums and Obstacle DP, Orig Buffalo, MN, Buffalo Muni, Takeoff... 10 Bowling Green, OH, Wood County, RNAV (GPS) RWY 10, Orig-B Bowling Green, OH, Wood County, RNAV...

Analysis of the effects of boundary-layer control in the take-off and power-off landing performance characteristics of a liaison type of airplane

NASA Technical Reports Server (NTRS)

Horton, Elmer A; Loftin, Laurence K; Racisz, Stanley F; Quinn, John

1951-01-01

A performance analysis has been made to determine whether boundary-layer control by suction might reduce the minimum take-off and landing distances of a four-place or five-place airplane or a liaison type of airplane below those obtainable with conventional high-lift devices. The airplane was assumed to have a cruise duration of 5 hours at 60-percent power and to be operating from airstrips having a ground friction coefficient of 0.2 or a combined ground and braking coefficient of 0.4. The payload was fixed at 1500 pounds, the wing span was varied from 25 to 100 feet, the aspect ratio was varied from 5 to 15, and the power was varied from 300 to 1300 horsepower. Maximum lift coefficients of 5.0 and 2.8 were assumed for the airplanes with and without boundary-layer-control --equipment weight was included. The effects of the boundary-layer control on total take-off distance, total power-off landing distance, landing and take-off ground run, stalling speed, sinking speed, and gliding speed were determined.

S.S.T.O. performance assessment with in-flight lox collection

NASA Astrophysics Data System (ADS)

Vandenkerckhove, J.; Czysz, P.

1995-10-01

Much attention has recently been given, up to harware development to in-flight oxygen collection as a means to improve considerably the performance of both TSTO & SSTO vehicles. A first assessment suggests that it permits simultaneously to improve much both gross take-off weight (by more than 30%) & dry weight (by more than 15%) of an SSTO and to lower significantly the Mach number of transition scramjet → rocket, from 15 down below 10, thereby reducing dramatically the programmatic development risks. After having compared in-flight lox collection with other SSTO concepts, this paper provides a tentative assessment of the performance of SSTO vehicles taking advantage of it, in particular their sensitivity to changes in system characteristics such as transition Mach number, vehicle slenderness (i.e. Küchemann's parameter τ) or planform loading at take-off and in collection characteristics, in particular collection ratio & specific collection plant weight.

78 FR 54564 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-05

... Linder Rgnl, Takeoff Minimums and Obstacle DP, Amdt 1 Venice, FL, Venice Muni, RNAV (GPS) RWY 5, Orig Venice, FL, Venice Muni, RNAV (GPS) RWY 23, Orig Venice, FL, Venice Muni, Takeoff Minimums and Obstacle...

75 FR 72942 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-29

..., Takeoff Minimums and Obstacle DP, Amdt 3 Harvard, NE, Harvard State, RNAV (GPS) RWY 35, Orig Harvard, NE, Harvard State, Takeoff Minimums and Obstacle DP, Orig Harvard, NE, Harvard State, VOR/DME RNAV OR GPS RWY...

Study of cabin noise control for twin engine general aviation aircraft

NASA Astrophysics Data System (ADS)

Vaicaitis, R.; Slazak, M.

1982-02-01

An analytical model based on modal analysis was developed to predict the noise transmission into a twin-engine light aircraft. The model was applied to optimize the interior noise to an A-weighted level of 85 dBA. To achieve the required noise attenuation, add-on treatments in the form of honeycomb panels, damping tapes, acoustic blankets, septum barriers and limp trim panels were added to the existing structure. The added weight of the noise control treatment is about 1.1 percent of the total gross take-off weight of the aircraft.

Cabin Noise Control for Twin Engine General Aviation Aircraft

NASA Technical Reports Server (NTRS)

Vaicaitis, R.; Slazak, M.

1982-01-01

An analytical model based on modal analysis was developed to predict the noise transmission into a twin-engine light aircraft. The model was applied to optimize the interior noise to an A-weighted level of 85 dBA. To achieve the required noise attenuation, add-on treatments in the form of honeycomb panels, damping tapes, acoustic blankets, septum barriers and limp trim panels were added to the existing structure. The added weight of the noise control treatment is about 1.1 percent of the total gross take-off weight of the aircraft.

Optimal trajectories for hypersonic launch vehicles

NASA Technical Reports Server (NTRS)

Ardema, Mark D.; Bowles, Jeffrey V.; Whittaker, Thomas

1992-01-01

In this paper, we derive a near-optimal guidance law for the ascent trajectory from Earth surface to Earth orbit of a hypersonic, dual-mode propulsion, lifting vehicle. Of interest are both the optimal flight path and the optimal operation of the propulsion system. The guidance law is developed from the energy-state approximation of the equations of motion. The performance objective is a weighted sum of fuel mass and volume, with the weighting factor selected to give minimum gross take-off weight for a specific payload mass and volume.

Advancement of proprotor technology. Task 1: Design study summary. [aerodynamic concept of minimum size tilt proprotor research aircraft

NASA Technical Reports Server (NTRS)

1969-01-01

A tilt-proprotor proof-of-concept aircraft design study has been conducted. The results are presented. The ojective of the contract is to advance the state of proprotor technology through design studies and full-scale wind-tunnel tests. The specific objective is to conduct preliminary design studies to define a minimum-size tilt-proprotor research aircraft that can perform proof-of-concept flight research. The aircraft that results from these studies is a twin-engine, high-wing aircraft with 25-foot, three-bladed tilt proprotors mounted on pylons at the wingtips. Each pylon houses a Pratt and Whitney PT6C-40 engine with a takeoff rating of 1150 horsepower. Empty weight is estimated at 6876 pounds. The normal gross weight is 9500 pounds, and the maximum gross weight is 12,400 pounds.

Intra-specific variation in wing morphology and its impact on take-off performance in blue tits (Cyanistes caeruleus) during escape flights

PubMed Central

McFarlane, Laura; Altringham, John D.; Askew, Graham N.

2016-01-01

ABSTRACT Diurnal and seasonal increases in body mass and seasonal reductions in wing area may compromise a bird's ability to escape, as less of the power available from the flight muscles can be used to accelerate and elevate the animal's centre of mass. Here, we investigated the effects of intra-specific variation in wing morphology on escape take-off performance in blue tits (Cyanistes caeruleus). Flights were recorded using synchronised high-speed video cameras and take-off performance was quantified as the sum of the rates of change of the kinetic and potential energies of the centre of mass. Individuals with a lower wing loading, WL (WL=body weight/wing area) had higher escape take-off performance, consistent with the increase in lift production expected from relatively larger wings. Unexpectedly, it was found that the total power available from the flight muscles (estimated using an aerodynamic analysis) was inversely related to WL. This could simply be because birds with a higher WL have relatively smaller flight muscles. Alternatively or additionally, variation in the aerodynamic load on the wing resulting from differences in wing morphology will affect the mechanical performance of the flight muscles via effects on the muscle's length trajectory. Consistent with this hypothesis is the observation that wing beat frequency and relative downstroke duration increase with decreasing WL; both are factors that are expected to increase muscle power output. Understanding how wing morphology influences take-off performance gives insight into the potential risks associated with feather loss and seasonal and diurnal fluctuations in body mass. PMID:26994175

Monitoring techniques for the X-29A aircraft's high-speed rotating power takeoff shaft

NASA Technical Reports Server (NTRS)

Voracek, David F.

1990-01-01

The experimental X-29A forward swept-wing aircraft has many unique and critical systems that require constant monitoring during ground or flight operation. One such system is the power takeoff shaft, which is the mechanical link between the engine and the aircraft-mounted accessory drive. The X-29A power takeoff shaft opertes in a range between 0 and 16,810 rpm, is longer than most jet engine power takeoff shafts, and is made of graphite epoxy material. Since the X-29A aircraft operates on a single engine, failure of the shaft during flight could lead to loss of the aircraft. The monitoring techniques and test methods used during power takeoff shaft ground and flight operations are discussed. Test data are presented in two case studies where monitoring and testing of the shaft dynamics proved instrumental in discovering and isolating X-29A power takeoff shaft problems. The first study concerns the installation of an unbalanced shaft. The effect of the unbalance on the shaft vibration data and the procedure used to correct the problem are discussed. The second study deals with the shaft exceeding the established vibration limits during flight. This case study found that the vibration of connected rotating machinery unbalances contributed to the excessive vibration level of the shaft. The procedures used to identify the contributions of other rotating machinery unbalances to the power takeoff shaft unbalance are discussed.

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Wing planform study and final configuration selection

NASA Technical Reports Server (NTRS)

1981-01-01

The Wing Planform Study and Final Configuration Selection Task of the Integrated Application of Active Controls (IAAC) Technology Project within the Energy Efficient Transport Program is documented. Application of Active Controls Technology (ACT) in combination with increased wing span resulted in significant improvements over the Conventional Baseline Configuration (Baseline) and the Initial ACT Configuration previously established. The configurations use the same levels of technology, takeoff gross weight, and payload as the Baseline. The Final ACT Configuration (Model 768-107) incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 44% reduction in horizontal tail size), lateral/directional-augmented stability, an angle-of-attack limiter, and wing-load alleviation. Flutter-mode control was not beneficial for this configuration. This resulted in an 890 kg (1960 lb) reduction in airplane takeoff gross weight and a 9.8% improvement in cruise lift/drag. At the Baseline mission range (3589 km 1938 nmi), this amounts to 10% block-fuel reduction. Results of this task strongly indicate that the IAAC Project should proceed with the Final ACT evaluation, and begin the required control system development and test.

The calculated effect of trailing-edge flaps on the take-off of flying boats

NASA Technical Reports Server (NTRS)

Parkinson, J E; Bell, J W

1934-01-01

The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust. It is indicated that flaps would allow a decrease in the high angles of wing setting necessary with most seaplanes, provided that the excess thrust is not too low.

Viability of Cross-Flow Fan for Vertical Take-Off and Landing Aircraft

DTIC Science & Technology

2012-06-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release; distribution is unlimited VIABILITY OF CROSS...FLOW FAN FOR VERTICAL TAKE-OFF AND LANDING AIRCRAFT by Christopher T. Delagrange June 2012 Thesis Advisor: Garth V. Hobson Second...AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE Viability of Cross-Flow Fan for Vertical Take-Off and Landing Aircraft 5. FUNDING

Optimal Trajectories for the Helicopter in One-Engine-Inoperative Terminal-Area Operations

NASA Technical Reports Server (NTRS)

Zhao, Yiyuan; Chen, Robert T. N.

1996-01-01

This paper presents a summary of a series of recent analytical studies conducted to investigate One-Engine-Inoperative (OEI) optimal control strategies and the associated optimal trajectories for a twin engine helicopter in Category-A terminal-area operations. These studies also examine the associated heliport size requirements and the maximum gross weight capability of the helicopter. Using an eight states, two controls, augmented point-mass model representative of the study helicopter, Continued TakeOff (CTO), Rejected TakeOff (RTO), Balked Landing (BL), and Continued Landing (CL) are investigated for both Vertical-TakeOff-and-Landing (VTOL) and Short-TakeOff-and-Landing (STOL) terminal-area operations. The formulation of the nonlinear optimal control problems with considerations for realistic constraints, solution methods for the two-point boundary-value problem, a new real-time generation method for the optimal OEI trajectories, and the main results of this series of trajectory optimization studies are presented. In particular, a new balanced- weight concept for determining the takeoff decision point for VTOL Category-A operations is proposed, extending the balanced-field length concept used for STOL operations.

Preliminary design of a supersonic Short-Takeoff and Vertical-Landing (STOVL) fighter aircraft

NASA Technical Reports Server (NTRS)

1990-01-01

A preliminary study of a supersonic short takeoff and vertical landing (STOVL) fighter is presented. Three configurations (a lift plus lift/cruise concept, a hybrid fan vectored thrust concept, and a mixed flow vectored thrust concept) were initially investigated with one configuration selected for further design analysis. The selected configuration, the lift plus lift/cruise concept, was successfully integrated to accommodate the powered lift short takeoff and vertical landing requirements as well as the demanding supersonic cruise and point performance requirements. A supersonic fighter aircraft with a short takeoff and vertical landing capability using the lift plus lift/cruise engine concept seems a viable option for the next generation fighter.

14 CFR 23.51 - Takeoff speeds.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff speeds. 23.51 Section 23.51... speeds. (a) For normal, utility, and acrobatic category airplanes, rotation speed, VR, is the speed at... seaplanes and amphibians taking off from water, VR, may be any speed that is shown to be safe under all...

14 CFR 23.51 - Takeoff speeds.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff speeds. 23.51 Section 23.51... speeds. (a) For normal, utility, and acrobatic category airplanes, rotation speed, VR, is the speed at... seaplanes and amphibians taking off from water, VR, may be any speed that is shown to be safe under all...

Hot Water Propulsion for Horizontal Rocket Assisted Take-Off Systems for Future Reusable Launch Vehicles

NASA Astrophysics Data System (ADS)

Pilz, N.; Adirim, H.; Lo, R.; Schildknecht, A.

2004-10-01

Among other concepts, reusable space transportation systems that comprise winged reusable launch vehicles (RLV) with horizontal take-off and horizontal landing (HTHL) are under worldwide investigation, e.g. the respective concepts within ESA's FESTIP-Study (Future European Space Transportation Integration Program) or the HOPPER concept by EADS-ST. The payload of these RLVs could be significantly increased by means of a ground-based take-off assistance system that would accelerate the vehicle along a horizontal track until it reaches the desired speed to ignite its onboard engines for leaving the ground and launching into orbit. This paper illustrates the advantages of horizontal take-off for winged RLVs and provides an overview of launch-assist options for HTHL RLVs. It presents hot water propulsion for ground-based take-off assistance systems for future RLVs as an attractive choice besides magnetic levitation and acceleration (maglev) technology. Finally, preliminary design concepts are presented for a rocket assisted take-off system (RATOS) with hot water propulsion followed by an analysis of its improvement potential.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Lee H. (Inventor)

1989-01-01

The invention is a real-time takeoff and landing performance monitoring system which provides the pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V sub R) within the safe zone of the runway or stopping the aircraft on the runway after landing or take off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. An important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in headwind occurring as the takeoff roll progresses. The system displays the position of the airplane on the runway, indicating runway used and runway available, summarizes the critical information into a situation advisory flag, flags engine failures and off-nominal acceleration performance, and indicates where on the runway particular events such as decision speed (V sub 1), rotation speed (V sub R) and expected stop points will occur based on actual or predicted performance. The display also indicates airspeed, wind vector, engine pressure ratios, second segment climb speed, and balanced field length (BFL). The system detects performance deficiencies by comparing the airplane's present performance with a predicted nominal performance based upon the given conditions.

The Calculated Effect of Various Hydrodynamic and Aerodynamic Factors on the Take-Off of a Large Flying Boat

NASA Technical Reports Server (NTRS)

Olson, R.E.; Allison, J.M.

1939-01-01

Present designs for large flying boats are characterized by high wing loading, high aspect ratio, and low parasite drag. The high wing loading results in the universal use of flaps for reducing the takeoff and landing speeds. These factors have an effect on takeoff performance and influence to a certain extent the design of the hull. An investigation was made of the influence of various factors and design parameters on the takeoff performance of a hypothetical large flying boat by means of takeoff calculations. The parameters varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The takeoff times and distances were calculated to the stalling speeds and the performance above these speeds was studied separately to determine piloting technique for optimum takeoff. The advantage of quick deflection of the flap at high water speeds is shown.

Transition from leg to wing forces during take-off in birds.

PubMed

Provini, Pauline; Tobalske, Bret W; Crandell, Kristen E; Abourachid, Anick

2012-12-01

Take-off mechanics are fundamental to the ecology and evolution of flying animals. Recent research has revealed that initial take-off velocity in birds is driven mostly by hindlimb forces. However, the contribution of the wings during the transition to air is unknown. To investigate this transition, we integrated measurements of both leg and wing forces during take-off and the first three wingbeats in zebra finch (Taeniopygia guttata, body mass 15 g, N=7) and diamond dove (Geopelia cuneata, body mass 50 g, N=3). We measured ground reaction forces produced by the hindlimbs using a perch mounted on a force plate, whole-body and wing kinematics using high-speed video, and aerodynamic forces using particle image velocimetry (PIV). Take-off performance was generally similar between species. When birds were perched, an acceleration peak produced by the legs contributed to 85±1% of the whole-body resultant acceleration in finch and 77±6% in dove. At lift-off, coincident with the start of the first downstroke, the percentage of hindlimb contribution to initial flight velocity was 93.6±0.6% in finch and 95.2±0.4% in dove. In finch, the first wingbeat produced 57.9±3.4% of the lift created during subsequent wingbeats compared with 62.5±2.2% in dove. Advance ratios were <0.5 in both species, even when taking self-convection of shed vortices into account, so it was likely that wing-wake interactions dominated aerodynamics during wingbeats 2 and 3. These results underscore the relatively low contribution of the wings to initial take-off, and reveal a novel transitional role for the first wingbeat in terms of force production.

76 FR 4250 - Operating Certain Railroad Tank Cars in Excess of 263,000 Pounds Gross Rail Load; Approval

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-25

... Railroad Tank Cars in Excess of 263,000 Pounds Gross Rail Load; Approval AGENCY: Federal Railroad... certain railroad tank cars in excess of 263,000 pounds gross rail load. SUMMARY: On May 14, 2010, the... to allow certain rail tank cars, transporting hazardous materials, to exceed the gross weight on rail...

14 CFR 29.59 - Takeoff path: Category A.

Code of Federal Regulations, 2010 CFR

2010-01-01

... addition— (1) The takeoff path must remain clear of the height-velocity envelope established in accordance with § 29.87; (2) The rotorcraft must be flown to the engine failure point; at which point, the...

Hybrid vehicle powertrain system with power take-off driven vehicle accessory

DOEpatents

Beaty, Kevin D.; Bockelmann, Thomas R.; Zou, Zhanijang; Hope, Mark E.; Kang, Xiaosong; Carpenter, Jeffrey L.

2006-09-12

A hybrid vehicle powertrain system includes a first prime mover, a first prime mover driven power transmission mechanism having a power take-off adapted to drive a vehicle accessory, and a second prime mover. The second prime mover is operable to drive the power transmission mechanism alone or in combination with the first prime mover to provide power to the power take-off through the power transmission mechanism. The invention further includes methods for operating a hybrid vehicle powertrain system.

WAATS: A computer program for Weights Analysis of Advanced Transportation Systems

NASA Technical Reports Server (NTRS)

Glatt, C. R.

1974-01-01

A historical weight estimating technique for advanced transportation systems is presented. The classical approach to weight estimation is discussed and sufficient data is presented to estimate weights for a large spectrum of flight vehicles including horizontal and vertical takeoff aircraft, boosters and reentry vehicles. A computer program, WAATS (Weights Analysis for Advanced Transportation Systems) embracing the techniques discussed has been written and user instructions are presented. The program was developed for use in the ODIN (Optimal Design Integration System) system.

The calculated effect of various hydrodynamic and aerodynamic factors on the take-off of a large flying boat

NASA Technical Reports Server (NTRS)

Olson, R E; Allison, J M

1940-01-01

Report presents the results of an investigation made to determine the influence of various factors on the take-off performance of a hypothetical large flying boat by means of take-off calculations. The factors varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The take-off times and distances were calculated to the stalling speeds and the performance above these speeds was separately studied to determine piloting technique for optimum take-off.

Supersonic fan engines for military aircraft

NASA Technical Reports Server (NTRS)

Franciscus, L. C.

1983-01-01

Engine performance and mission studies were performed for turbofan engines with supersonic through-flow fans. A Mach 2.4 CTOL aircraft was used in the study. Two missions were considered: a long range penetrator mission and a long range intercept mission. The supersonic fan engine is compared with an augmented mixed flow turbofan in terms of mission radius for a fixed takeoff gross weight of 75,000 lbm. The mission radius of aircraft powered by supersonic fan engines could be 15 percent longer than aircraft powered with conventional turbofan engines at moderate thrust to gross weight ratios. The climb and acceleration performance of the supersonic fan engines is better than that of the conventional turbofan engines. Previously announced in STAR as N83-34947

75 FR 32653 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

... Giddings, TX, Giddings-Lee County, Takeoff Minimum and Obstacle DP, Orig Hebbronville, TX, Jim Hogg County, GPS RWY 13, Amdt 1A, CANCELLED Hebbronville, TX, Jim Hogg County, NDB RWY 13, Amdt 4 Hebbronville, TX, Jim Hogg County, RNAV (GPS) RWY 13, Orig Hebbronville, TX, Jim Hogg County, Takeoff Minimum and...

14 CFR 25.703 - Takeoff warning system.

Code of Federal Regulations, 2013 CFR

2013-01-01

... requirements of § 25.671), speed brakes, or longitudinal trim devices are in a position that would not allow a... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Takeoff warning system. 25.703 Section 25.703 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

14 CFR 25.703 - Takeoff warning system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... requirements of § 25.671), speed brakes, or longitudinal trim devices are in a position that would not allow a... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Takeoff warning system. 25.703 Section 25.703 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

14 CFR 25.703 - Takeoff warning system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... requirements of § 25.671), speed brakes, or longitudinal trim devices are in a position that would not allow a... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff warning system. 25.703 Section 25.703 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

14 CFR 25.703 - Takeoff warning system.

Code of Federal Regulations, 2012 CFR

2012-01-01

... requirements of § 25.671), speed brakes, or longitudinal trim devices are in a position that would not allow a... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Takeoff warning system. 25.703 Section 25.703 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT...

Gross Motor Development.

ERIC Educational Resources Information Center

Florida Learning Resources System/CROWN, Jacksonville.

The document is designed to help teachers identify and remediate gross motor development deficits in elementary school students. A definition of gross motor development and a checklist of gross motor skills are provided. Sections cover the following topics: successful teaching techniques; activities for perceptual-motor training; activities for…

75 FR 19541 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-15

.... The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and the need... DP, Amdt 2 Alexandria, MN, Chandler Field, RNAV (GPS) RWY 22, Orig Bemidji, MN, Bemidji Rgnl, RNAV (GPS) RWY 25, Orig Granite Falls, MN, Granite Falls Muni/Lenzen-Roe Meml Fld, Takeoff Minimums and...

76 FR 70053 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and... Three Rivers, MI, Three Rivers Muni Dr. Haines, Takeoff Minimums and Obstacle DP, Orig Brainerd, MN, Brainerd Lakes Rgnl, ILS OR LOC/DME RWY 34, Amdt 1 Park Rapids, MN, Park Rapids Muni-Konshok Field, NDB RWY...

78 FR 18806 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

... on 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex..., ILS OR LOC/DME RWY 24, Amdt 2B Faribault, MN, Faribault Muni, RNAV (GPS) RWY 12, Amdt1 Faribault, MN, Faribault Muni, RNAV (GPS) RWY 30, Amdt1 Minneapolis, MN, Minneapolis-St Paul Intl/Wold-Chamberlain, Takeoff...

77 FR 12452 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-01

... OR LOC Z RWY 8, Amdt 37 Burbank, CA, Bob Hope, LOC Y RWY 8, Amdt 4 Colorado Springs, CO, City of Colorado Springs Muni, Takeoff Minimums and Obstacle DP, Amdt 10 Craig, CO, Craig-Moffat, Takeoff Minimums and Obstacle DP, Amdt 4 Durango, CO, Durango-La Plata County, VOR/DME RWY 3, Amdt 5 Pueblo, CO, Pueblo...

76 FR 43580 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-21

..., Raleigh Exec Jetport at Sanford-Lee County, Takeoff Minimums and Obstacle DP, Amdt 1 Rugby, ND, Rugby Muni, GPS RWY 12, Orig, CANCELLED Rugby, ND, Rugby Muni, GPS RWY 30, Orig-B, CANCELLED Rugby, ND, Rugby Muni, RNAV (GPS) RWY 12, Orig Rugby, ND, Rugby Muni, RNAV (GPS) RWY 30, Orig Rugby, ND, Rugby Muni, Takeoff...

Optimal trajectories for hypersonic launch vehicles

NASA Technical Reports Server (NTRS)

Ardema, Mark D.; Bowles, Jeffrey V.; Whittaker, Thomas

1994-01-01

In this paper, we derive a near-optimal guidance law for the ascent trajectory from earth surface to earth orbit of a hypersonic, dual-mode propulsion, lifting vehicle. Of interest are both the optical flight path and the optimal operation of the propulsion system. The guidance law is developed from the energy-state approximation of the equations of motion. Because liquid hydrogen fueled hypersonic aircraft are volume sensitive, as well as weight sensitive, the cost functional is a weighted sum of fuel mass and volume; the weighting factor is chosen to minimize gross take-off weight for a given payload mass and volume in orbit.

Correlation of climbing perception and eye movements during daytime and nighttime takeoffs using a flight simulator.

PubMed

Tamura, Atsushi; Wada, Yoshiro; Shimizu, Naoki; Inui, Takuo; Shiotani, Akihiro

2016-01-01

This study suggests that the subjective climbing perception can be quantitatively evaluated using values calculated from induced eye movements, and the findings may aid in the detection of pilots who are susceptible to spatial disorientation in a screening test. The climbing perception experienced by a pilot during takeoff at night is stronger than that experienced during the day. To investigate this illusion, this study assessed eye movements and analyzed their correlation with subjective climbing perception during daytime and nighttime takeoffs. Eight male volunteers participated in this study. A simulated aircraft takeoff environment was created using a flight simulator and the maximum slow-phase velocities and vestibulo-ocular reflex gain of vertical eye movements were calculated during takeoff simulation. Four of the eight participants reported that their perception of climbing at night was stronger, while the other four reported that there was no difference between day and night. These perceptions were correlated with eye movements; participants with a small difference in the maximum slow-phase velocities of their downward eye movements between daytime and nighttime takeoffs indicated that their perception of climbing was the same under the two conditions.

Measurement of the Errors of Service Altimeter Installations During Landing-Approach and Take-Off Operations

NASA Technical Reports Server (NTRS)

Gracey, William; Jewel, Joseph W., Jr.; Carpenter, Gene T.

1960-01-01

The overall errors of the service altimeter installations of a variety of civil transport, military, and general-aviation airplanes have been experimentally determined during normal landing-approach and take-off operations. The average height above the runway at which the data were obtained was about 280 feet for the landings and about 440 feet for the take-offs. An analysis of the data obtained from 196 airplanes during 415 landing approaches and from 70 airplanes during 152 take-offs showed that: 1. The overall error of the altimeter installations in the landing- approach condition had a probable value (50 percent probability) of +/- 36 feet and a maximum probable value (99.7 percent probability) of +/- 159 feet with a bias of +10 feet. 2. The overall error in the take-off condition had a probable value of +/- 47 feet and a maximum probable value of +/- 207 feet with a bias of -33 feet. 3. The overall errors of the military airplanes were generally larger than those of the civil transports in both the landing-approach and take-off conditions. In the landing-approach condition the probable error and the maximum probable error of the military airplanes were +/- 43 and +/- 189 feet, respectively, with a bias of +15 feet, whereas those for the civil transports were +/- 22 and +/- 96 feet, respectively, with a bias of +1 foot. 4. The bias values of the error distributions (+10 feet for the landings and -33 feet for the take-offs) appear to represent a measure of the hysteresis characteristics (after effect and recovery) and friction of the instrument and the pressure lag of the tubing-instrument system.

Design optimization of high-speed proprotor aircraft

NASA Technical Reports Server (NTRS)

Schleicher, David R.; Phillips, James D.; Carbajal, Kevin B.

1993-01-01

NASA's high-speed rotorcraft (HSRC) studies have the objective of investigating technology for vehicles that have both low downwash velocities and forward flight speed capability of up to 450 knots. This paper investigates a tilt rotor, a tilt wing, and a folding tilt rotor designed for a civil transport mission. Baseline aircraft models using current technology are developed for each configuration using a vertical/short takeoff and landing (V/STOL) aircraft design synthesis computer program to generate converged vehicle designs. Sensitivity studies and numerical optimization are used to illustrate each configuration's key design tradeoffs and constraints. Minimization of the gross takeoff weight is used as the optimization objective function. Several advanced technologies are chosen, and their relative impact on future configurational development is discussed. Finally, the impact of maximum cruise speed on vehicle figures of merit (gross weight, productivity, and direct operating cost) is analyzed. The three most important conclusions from the study are payload ratios for these aircraft will be commensurate with current fixed-wing commuter aircraft; future tilt rotors and tilt wings will be significantly lighter, more productive, and cheaper than competing folding tilt rotors; and the most promising technologies are an advanced-technology proprotor for both tilt rotor and tilt wing and advanced structural materials for the folding tilt rotor.

Visual Confirmation of Voice Takeoff Clearance (VICON) Alternative Study

DOT National Transportation Integrated Search

1980-05-01

This report presents the results of a program undertaken to study potential alternatives to the VICON (Visual Confirmation of Voice Takeoff Clearance) System which has undergone operational field tests at Bradley International Airport, Windsor Locks,...

Preliminary performance of a vertical-attitude takeoff and landing, supersonic cruise aircraft concept having thrust vectoring integrated into the flight control system

NASA Technical Reports Server (NTRS)

Robins, A. W.; Beissner, F. L., Jr.; Domack, C. S.; Swanson, E. E.

1985-01-01

A performance study was made of a vertical attitude takeoff and landing (VATOL), supersonic cruise aircraft concept having thrust vectoring integrated into the flight control system. Those characteristics considered were aerodynamics, weight, balance, and performance. Preliminary results indicate that high levels of supersonic aerodynamic performance can be achieved. Further, with the assumption of an advanced (1985 technology readiness) low bypass ratio turbofan engine and advanced structures, excellent mission performance capability is indicated.

The weight status of school-age children and its association with gross domestic product.

PubMed

Grajda, Aneta; Kułaga, Zbigniew; Gurzkowska, Beata; Góźdź, Magdalena; Wojtyło, Małgorzata; Litwin, Mieczysław

2017-01-01

To examine the possible relationship between the prevalence of underweight, overweight and obesity of Polish children and adolescents and the gross domestic product per capita (GDP). This report is based on the results of a nationwide, representative population study. An area of the country, the so-called Eastern Poland, where GDP per capita is less than 80% of the national average, was designated, based on the data from the Central Statistical Office of Poland (CSOP) and was compared with the rest of the country. The frequency of underweight, normal weight, overweight and obesity, as well as the odds ratio were calculated for gender and region of residence. The body mass index (BMI) for age and sex was standardized and expressed as z-score. The statistical significance of standardized mean differences of BMI depending on the area was examined using the t-test. There were significant differences in the prevalence of underweight, overweight and obesity between the regions analyzed. The region of Eastern Poland was characterized by a lower risk of overweight and obesity and an increased risk of underweight in comparison with the rest of the country. Identification of the diverse prevalence of overweight and underweight depending on the region and determined according to the economic status is an opportunity to modify and adapt the strategy of implementing programs aimed at promoting healthy behaviours.

Degeneration of the long biceps tendon: comparison of MRI with gross anatomy and histology.

PubMed

Buck, Florian M; Grehn, Holger; Hilbe, Monika; Pfirrmann, Christian W A; Manzanell, Silvana; Hodler, Jürg

2009-11-01

The objective of our study was to relate alterations in biceps tendon diameter and signal on MR images to gross anatomy and histology. T1-weighted, T2-weighted fat-saturated, and proton density-weighted fat-saturated spin-echo sequences were acquired in 15 cadaveric shoulders. Biceps tendon diameter (normal, flattened, thickened, and partially or completely torn) and signal intensity (compared with bone, fat, muscle, and joint fluid) were graded by two readers independently and in a blinded fashion. The distance of tendon abnormalities from the attachment at the glenoid were noted in millimeters. MRI findings were related to gross anatomic and histologic findings. On the basis of gross anatomy, there were six normal, five flattened, two thickened, and two partially torn tendons. Reader 1 graded nine diameter changes correctly, missed two, and incorrectly graded four. The corresponding values for reader 2 were seven, one, and five, respectively, with kappa = 0.75. Histology showed mucoid degeneration (n = 13), lipoid degeneration (n = 7), and fatty infiltration (n = 6). At least one type of abnormality was found in each single tendon. Mucoid degeneration was hyperintense compared with fatty infiltration on T2-weighted fat-saturated images and hyperintense compared with magic-angle artifacts on proton density-weighted fat-saturated images. MRI-based localization of degeneration agreed well with histologic findings. Diameter changes are specific but not sensitive in diagnosing tendinopathy of the biceps tendon. Increased tendon signal is most typical for mucoid degeneration but should be used with care as a sign of tendon degeneration.

Trajectory-Based Takeoff Time Predictions Applied to Tactical Departure Scheduling: Concept Description, System Design, and Initial Observations

NASA Technical Reports Server (NTRS)

Engelland, Shawn A.; Capps, Alan

2011-01-01

Current aircraft departure release times are based on manual estimates of aircraft takeoff times. Uncertainty in takeoff time estimates may result in missed opportunities to merge into constrained en route streams and lead to lost throughput. However, technology exists to improve takeoff time estimates by using the aircraft surface trajectory predictions that enable air traffic control tower (ATCT) decision support tools. NASA s Precision Departure Release Capability (PDRC) is designed to use automated surface trajectory-based takeoff time estimates to improve en route tactical departure scheduling. This is accomplished by integrating an ATCT decision support tool with an en route tactical departure scheduling decision support tool. The PDRC concept and prototype software have been developed, and an initial test was completed at air traffic control facilities in Dallas/Fort Worth. This paper describes the PDRC operational concept, system design, and initial observations.

14 CFR Appendix I to Part 25 - Installation of an Automatic Takeoff Thrust Control System (ATTCS)

Code of Federal Regulations, 2011 CFR

2011-01-01

... Appendix I to Part 25—Installation of an Automatic Takeoff Thrust Control System (ATTCS) I25.1General. (a... crew to increase thrust or power. I25.2Definitions. (a) Automatic Takeoff Thrust Control System (ATTCS... Control System (ATTCS) I Appendix I to Part 25 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION...

Evaluation of the Most Reliable Procedure of Determining Jump Height During the Loaded Countermovement Jump Exercise: Take-Off Velocity vs. Flight Time.

PubMed

Pérez-Castilla, Alejandro; García-Ramos, Amador

2018-07-01

Pérez-Castilla, A and García-Ramos, A. Evaluation of the most reliable procedure of determining jump height during the loaded countermovement jump exercise: Take-off velocity vs. flight time. J Strength Cond Res 32(7): 2025-2030, 2018-This study aimed to compare the reliability of jump height between the 2 standard procedures of analyzing force-time data (take-off velocity [TOV] and flight time [FT]) during the loaded countermovement (CMJ) exercise performed with a free-weight barbell and in a Smith machine. The jump height of 17 men (age: 22.2 ± 2.2 years, body mass: 75.2 ± 7.1 kg, and height: 177.0 ± 6.0 cm) was tested in 4 sessions (twice for each CMJ type) against external loads of 17, 30, 45, 60, and 75 kg. Jump height reliability was comparable between the TOV (coefficient of variation [CV]: 6.42 ± 2.41%) and FT (CV: 6.53 ± 2.17%) during the free-weight CMJ, but it was higher for the FT when the CMJ was performed in a Smith machine (CV: 11.34 ± 3.73% for TOV and 5.95 ± 1.12% for FT). Bland-Altman plots revealed trivial differences (≤0.27 cm) and no heteroscedasticity of the errors (R ≤ 0.09) for the jump height obtained by the TOV and FT procedures, whereas the random error between both procedures was higher for the CMJ performed in the Smith machine (2.02 cm) compared with the free-weight barbell (1.26 cm). Based on these results, we recommend the FT procedure to determine jump height during the loaded CMJ performed in a Smith machine, whereas the TOV and FT procedures provide similar reliability during the free-weight CMJ.

49 CFR 375.509 - How must I determine the weight of a shipment?

Code of Federal Regulations, 2010 CFR

2010-10-01

...—origin weigh. You determine the difference between the tare weight of the vehicle before loading at the origin of the shipment and the gross weight of the same vehicle after loading the shipment. (2) Second method—back weigh. You determine the difference between the gross weight of the vehicle with the shipment...

Hypersonic transport technology

NASA Technical Reports Server (NTRS)

Kirkham, F. S.; Hunt, J. L.

1977-01-01

The possibility of developing a hypersonic commercial transport (HST) for the early 21st century is explored in terms of potential performance characteristics and recent advances in propulsion and structures technology. Range-gross weight characteristics indicate that a 200 passenger, Mach 6 aircraft with a range of 9200 km (5000 n.mi.) would have a gross take-off weight not too different from that of current wide-body subsonic transports. The low cruise sonic boom overpressures generated by the HST opens the possibility of supersonic overland flight which, if permitted, would greatly increase the attractiveness of this type of aircraft. Recent advances in hypersonic propulsion systems and long-lived hypersonic aircraft structure are also discussed. The airframe-integrated scramjet and the actively-cooled airframe structure are identified as the most promising candidates for the HST and current approaches are described in some detail.

Visual Confirmation (VICON) of Takeoff Clearance Signal System Impact Study

DOT National Transportation Integrated Search

1980-11-01

A study was performed to evaluate the impact on airport capacity and voice communications of the Visual Confirmation of Takeoff Clearance (VICON) Signal System. Befoe-and-after test data collection and analysis were conducted at Bradley International...

Single-stage-to-orbit performance enhancement from take-off thrust augmentation

NASA Astrophysics Data System (ADS)

Galati, Terence; Elkins, Travis

1997-01-01

Thrust augmentation offers the Single Stage to Orbit (SSTO) space launch vehicle improved payload capability while reducing vehicle weight and cost. Optimization of vehicle configuration and flight profile are studied. Using a 612,000 kg Gross Lift Off Weight (GLOW) SSTO with three Castor® strap-on motors, payloads in excess of 18,000 kg to Low Earth Orbit (LEO) are achievable. Emphasis is placed on finding vehicle optimums in the 9,000 kg payload range to capture over 80% of commercial payloads. Strap-on boosters allow a small SSTO vehicle to fly with a mass fraction of only 0.88 and LOX/H2 engines operating at 445 sec vacuum specific impulse. Payload sensitivity due to variations of mass fraction, Isp and pitch rate are quantified.

Light Duty Truck Weight Reduction Evaluation

DOT National Transportation Integrated Search

1980-10-01

The objectives of this program were to identify the weight reduction potential of pickup trucks, vans, and utility vehicles less than or equal to 8500 lb. gross vehicle weight through design modification, redesign, and material substitution; and more...

[Gross characteristics of placentas from an assisted reproduction program].

PubMed

Tabs, Dunja; Vejnović, Tihomir; Lalosević, Dusan; Radunović, Nebojsa

2006-01-01

Even though placentas from assisted reproduction programs often differ from placentas of women who conceived naturally, they are rarely examined. The aim of our investigation was to determine some gross characteristics of placentas of women who conceived with assisted reproduction. We examined 30 placentas from an assisted reproduction program (20 from in vitro fertilization and 10 from intrauterine insemination) and 30 placentas of women who conceived naturally. All women were age matched. All the women were at term. The mean weight of placentas from assisted reproduction program was 573 g and of those after natural conception--582.67g. The mean length of the umbilical cords was 64.3cm after assisted reproduction and 66.3cm after natural conception. The mean placenta thickness after assisted reproduction was 2,22 cm and after natural conception 2.28 cm. Eight placentas of the study group had a marginal insertion of the umbilical cord, which lead to a statistically significant difference when compared to placentas of women who conceived naturally: chi-square = 7.07; p>0.01. Marginal cord insertion into the placenta after assisted reproduction is also often described in the literature (as a possible "consequence" of embryo-transfer). There were no statistically significant differences in the mean weight and dimensions of placentas, length of the umbilical cord, gross pathological features of placentas and cords, mean birth weight of babies and placental/fetal ratios between women from assisted reproduction program and those who conceived naturally.

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

14 CFR 121.177 - Airplanes: Reciprocating engine-powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplanes: Reciprocating engine-powered... AND OPERATIONS OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS Airplane Performance Operating Limitations § 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. (a...

Pesticides and passive dispersal: acaricide- and starvation-induced take-off of the predatory mite Neoseiulus baraki.

PubMed

Monteiro, Vaneska Barbosa; Silva, Vanessa Farias; Lima, Debora Barbosa; Guedes, Raul Narciso Carvalho; Gondim, Manoel Guedes Correa

2018-06-01

An understanding of the causes and consequences of dispersal is vital for managing populations. Environmental contaminants, such as pesticides, provide potential environmental context-dependent stimuli for dispersal of targeted and non-targeted species, which may occur not only for active but also for passive dispersal, although such a possibility is frequently neglected. Here, we assessed the potential of food deprivation and acaricides to interfere with the take-off for passive (wind) dispersal of the predatory mite Neoseiulus baraki. Wind tunnel bioassays indicated that starvation favoured the take-off for wind dispersal by the mite predator, which also varied with wind velocity, and dispersal increased at higher velocities within the 1-7 (m s -1 ) range tested. For the acaricides tested, particularly the biopesticide azadirachtin but also abamectin and fenpyroximate, the rate of predator take-off for dispersal increased, and further increased with wind velocity up to 7 m/s. Such responses were associated with changes in the predator behavioural preparation for wind-mediated passive dispersal, with a greater incidence of the standing posture that permitted take-off. The rate of take-off for passive dispersal by N. baraki increased with food deprivation and exposure to the residues of agricultural acaricides. Azadirachtin exposure resulted in a particularly strong response, although abamectin and fenpyroximate also stimulated dispersal. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

AGFATL- ACTIVE GEAR FLEXIBLE AIRCRAFT TAKEOFF AND LANDING ANALYSIS

NASA Technical Reports Server (NTRS)

Mcgehee, J. R.

1994-01-01

The Active Gear, Flexible Aircraft Takeoff and Landing Analysis program, AGFATL, was developed to provide a complete simulation of the aircraft takeoff and landing dynamics problem. AGFATL can represent an airplane either as a rigid body with six degrees of freedom or as a flexible body with multiple degrees of freedom. The airframe flexibility is represented by the superposition of up to twenty free vibration modes on the rigid-body motions. The analysis includes maneuver logic and autopilots programmed to control the aircraft during glide slope, flare, landing, and takeoff. The program is modular so that performance of the aircraft in flight and during landing and ground maneuvers can be studied separately or in combination. A program restart capability is included in AGFATL. Effects simulated in the AGFATL program include: (1) flexible aircraft control and performance during glide slope, flare, landing roll, and takeoff roll under conditions of changing winds, engine failures, brake failures, control system failures, strut failures, restrictions due to runway length, and control variable limits and time lags; (2) landing gear loads and dynamics for up to five gears; (3) single and multiple engines (maximum of four) including selective engine reversing and failure; (4) drag chute and spoiler effects; (5) wheel braking (including skid-control) and selective brake failure; (6) aerodynamic ground effects; (7) aircraft carrier operations; (8) inclined runways and runway perturbations; (9) flexible or rigid airframes; 10) rudder and nose gear steering; and 11) actively controlled landing gear shock struts. Input to the AGFATL program includes data which describe runway roughness; vehicle geometry, flexibility and aerodynamic characteristics; landing gear(s); propulsion; and initial conditions such as attitude, attitude change rates, and velocities. AGFATL performs a time integration of the equations of motion and outputs comprehensive information on the airframe

14 CFR 121.199 - Nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... airplane can be safely controlled in flight after an engine becomes inoperative) or 115 percent of the... this section— (1) It may be assumed that takeoff power is used on all engines during the acceleration... reported tailwind component, may be taken into account; (3) The average runway gradient (the difference...

14 CFR 121.199 - Nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... airplane can be safely controlled in flight after an engine becomes inoperative) or 115 percent of the... this section— (1) It may be assumed that takeoff power is used on all engines during the acceleration... reported tailwind component, may be taken into account; (3) The average runway gradient (the difference...

14 CFR 121.199 - Nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... airplane can be safely controlled in flight after an engine becomes inoperative) or 115 percent of the... this section— (1) It may be assumed that takeoff power is used on all engines during the acceleration... reported tailwind component, may be taken into account; (3) The average runway gradient (the difference...

14 CFR 121.199 - Nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... airplane can be safely controlled in flight after an engine becomes inoperative) or 115 percent of the... this section— (1) It may be assumed that takeoff power is used on all engines during the acceleration... reported tailwind component, may be taken into account; (3) The average runway gradient (the difference...

14 CFR 121.199 - Nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... airplane can be safely controlled in flight after an engine becomes inoperative) or 115 percent of the... this section— (1) It may be assumed that takeoff power is used on all engines during the acceleration... reported tailwind component, may be taken into account; (3) The average runway gradient (the difference...

A Mission-Adaptive Variable Camber Flap Control System to Optimize High Lift and Cruise Lift-to-Drag Ratios of Future N+3 Transport Aircraft

NASA Technical Reports Server (NTRS)

Urnes, James, Sr.; Nguyen, Nhan; Ippolito, Corey; Totah, Joseph; Trinh, Khanh; Ting, Eric

2013-01-01

Boeing and NASA are conducting a joint study program to design a wing flap system that will provide mission-adaptive lift and drag performance for future transport aircraft having light-weight, flexible wings. This Variable Camber Continuous Trailing Edge Flap (VCCTEF) system offers a lighter-weight lift control system having two performance objectives: (1) an efficient high lift capability for take-off and landing, and (2) reduction in cruise drag through control of the twist shape of the flexible wing. This control system during cruise will command varying flap settings along the span of the wing in order to establish an optimum wing twist for the current gross weight and cruise flight condition, and continue to change the wing twist as the aircraft changes gross weight and cruise conditions for each mission segment. Design weight of the flap control system is being minimized through use of light-weight shape memory alloy (SMA) actuation augmented with electric actuators. The VCCTEF program is developing better lift and drag performance of flexible wing transports with the further benefits of lighter-weight actuation and less drag using the variable camber shape of the flap.

Evaluation of physical growth in cerebral palsied children and its possible relationship with gross motor development.

PubMed

Ibrahim, Alaa I; Hawamdeh, Ziad M

2007-03-01

The object of this study was to detect any possible relation between the current gross motor function score for cerebral palsy children and their physical growth parameters. We measured 71 children with spastic cerebral palsy (35 diplegic, 25 quadriplegic and 11 hemiplegic) and a control group of 80 normal children. Measures taken for cerebral palsy and normal children included stature, weight, head circumference and mid upper-arm circumference, and, additionally for the cerebral palsied children, duration of the disease, birth weight, presence or absence of orofacial dysfunction, distribution of paralysis and degree of spasticity. Motor abilities were measured using the Gross Motor Function Measure. Results showed a significant decrease in the stature, current weight, head circumference and mid upper-arm circumference of both sexes of the quadriplegic children, and significant decreases in the current weight of the diplegic girls and the head circumference of the hemiplegic girls. There were also significant decreases in all scores of the quadriplegic children compared to the diplegic and hemiplegic children. Diplegic children had significantly decreased standing, walking and running, and total scores, compared to the hemiplegic children. Total score at age of testing was independently predicted by the duration of the disease, distribution of paralysis, presence or absence of orofacial dysfunction, spasticity index and the current body weight. Our findings indicate that in spastic cerebral palsy the physical growth parameters were markedly decreased in the quadriplegic form compared to other forms. Only current body weight, from the growth parameters, in addition to other relevant clinical data, can be considered predictors of the current gross motor abilities of those children.

The Effect of Rotor Cruise Tip Speed, Engine Technology and Engine/Drive System RPM on the NASA Large Civil Tiltrotor (LCTR2) Size and Performance

NASA Technical Reports Server (NTRS)

Robuck, Mark; Wilkerson, Joseph; Maciolek, Robert; Vonderwell, Dan

2012-01-01

A multi-year study was conducted under NASA NNA06BC41C Task Order 10 and NASA NNA09DA56C task orders 2, 4, and 5 to identify the most promising propulsion system concepts that enable rotor cruise tip speeds down to 54% of the hover tip speed for a civil tiltrotor aircraft. Combinations of engine RPM reduction and 2-speed drive systems were evaluated. Three levels of engine and the drive system advanced technology were assessed; 2015, 2025 and 2035. Propulsion and drive system configurations that resulted in minimum vehicle gross weight were identified. Design variables included engine speed reduction, drive system speed reduction, technology, and rotor cruise propulsion efficiency. The NASA Large Civil Tiltrotor, LCTR, aircraft served as the base vehicle concept for this study and was resized for over thirty combinations of operating cruise RPM and technology level, quantifying LCTR2 Gross Weight, size, and mission fuel. Additional studies show design sensitivity to other mission ranges and design airspeeds, with corresponding relative estimated operational cost. The lightest vehicle gross weight solution consistently came from rotor cruise tip speeds between 422 fps and 500 fps. Nearly equivalent results were achieved with operating at reduced engine RPM with a single-speed drive system or with a two-speed drive system and 100% engine RPM. Projected performance for a 2025 engine technology provided improved fuel flow over a wide range of operating speeds relative to the 2015 technology, but increased engine weight nullified the improved fuel flow resulting in increased aircraft gross weights. The 2035 engine technology provided further fuel flow reduction and 25% lower engine weight, and the 2035 drive system technology provided a 12% reduction in drive system weight. In combination, the 2035 technologies reduced aircraft takeoff gross weight by 14% relative to the 2015 technologies.

Simulator evaluation of displays for a revised takeoff performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B.; Srivatsan, Raghavachari; Person, Lee H., Jr

1992-01-01

Cockpit displays for a Takeoff Performance Monitoring System (TOPMS) to provide pilots with graphic and alphanumeric information pertinent to their decision to continue or abort a takeoff are evaluated. Revised head-down and newly developed head-up displays were implemented on electronic screens in the real-time Transport Systems Research Vehicle (TSRV) Simulator for the Boeing 737 airplane at the Langley Research Center and evaluated by 17 NASA, U.S. Air Force, airline, and industry pilots. Both types of displays were in color, but they were not dependent upon it. The TOPMS head-down display is composed of a runway graphic overlaid with symbolic status and advisory information related to both the expected takeoff point and the predicted stop point (in the event an abort becomes necessary). In addition, an overall Situation Advisory Flag indicates a preferred course of action based on analysis of the various elements of airplane performance and system status. A simpler head-up display conveys most of this same information and relates it to the visual scene. The evaluation pilots found the displays to be credible, easy to monitor, and appropriate for the task. In particular, the pilots said the head-up display was monitored with very little effort and did not obstruct or distract them from monitoring the simulated out-the-window runway scene. This report augments NASA TP-2908, 1989.

Resistance Tests of a 1/16 Size Model of the Hughes-kaiser Flying Boat, NACA Model 183

NASA Technical Reports Server (NTRS)

Posner, Jack; Woodward, David R.; Olson, Roland E.

1944-01-01

Tank tests were made of a hull model of the Hughes-Kaiser cargo airplane for estimates of take-off performance and maximum gross load for take-off. At hump speeds, with the model free to trim, the trim and resistance were high, which resulted in a load-resistance ratio of approximately 4.0 for a gross load coefficient of 0.75. With a 4000,000-lb load, the full size craft may take off in 69 sec over a distance of 5600 ft.

14 CFR 135.389 - Large nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Large nontransport category airplanes: Takeoff limitations. 135.389 Section 135.389 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.389 Large nontransport...

14 CFR 135.389 - Large nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Large nontransport category airplanes: Takeoff limitations. 135.389 Section 135.389 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.389 Large nontransport...

Gross-alpha and gross-beta activities in airborne particulate samples. Analysis and prediction models.

PubMed

Dueñas, C; Fernández, M C; Carretero, J; Liger, E; Cañete, S

2001-04-01

Measurements of gross-alpha and gross-beta activities were made every week during the years 1992-1997 for airborne particulate samples collected using air filters at a clear site. The data are sufficiently numerous to allow the examination of variations in time and by these measurements to establish several features that should be important in understanding any trends of atmospheric radioactivity. Two models were used to predict the gross-alpha and gross-beta activities. A good agreement between the results of these models and the measurements was highlighted.

Phase 2 program on ground test of refanned JT8D turbofan engines and nacelles for the 727 airplane. Volume 4: Airplane evaluation and analysis

NASA Technical Reports Server (NTRS)

1975-01-01

The retrofit of JT8D-109 (refan) engines are evaluated on a 727-200 airplane in terms of airworthiness, performance, and noise. Design of certifiable hardware, manufacture, and ground testing of the essential nacelle components is included along with analysis of the certifiable airplane design to ensure airworthiness compliance and to predict the in-flight performance and noise characteristics of the modified airplane. The analyses confirm that the 727 refan airplane is certifiable. The refan airplane range would be 15% less that of the baseline airplane and block fuel would be increased by 1.5% to 3%. However, with this particular 727-200 model, with a brake release gross weight of 172,500 lb (78,245 kg), it is possible to operate the airplane (with minor structural modifications) at higher gross weights and increase the range up to 15% over the 727-200 (baseline) airplane. The refan airplane FAR Part 36 noise levels would be 6 to 8 EPNdB (effective perceived noise in decibels) below the baseline. Noise footprint studies showed that approach noise contour areas are small compared to takeoff areas. The 727 refan realizes a 68% to 83% reduction in annoyance-weighted area when compared to the 727-200 over a range of gross weights and operational procedures.

Design integration and noise studies for jet STOL aircraft. Task 7A: Augmentor wing cruise blowing valveless system. Volume 1: System design and test integration

NASA Technical Reports Server (NTRS)

Roepcke, F. A.; Nickson, T. B.

1973-01-01

Exploratory design studies conducted to establish the configuration of an augmentor wing vruise blowing (valveless) system in a 150-passenger STOL airplane were reported in NASA CR-114570. Those studies have been updated to incorporate the results of static rig, flow duct, and wind tunnel tests. Minor adjustments in duct flow velocity, flap length, and blowing nozzle geometry were incorporated to provide airplane characteristics that minimize takeoff gross weight and achieve sideline noise objectives for an advanced commercial STOL airplane.

Technology sensitivity studies for a Mach 3.0 civil transport

NASA Technical Reports Server (NTRS)

Coen, Peter G.

1988-01-01

The level of technological sophistication required for the economic viability and environmental acceptability of a Mach 3.0-cruise SST is evaluated, with a view to the development schedule and initial operating date into which the maturity of various essential technologies will translate. Attention is given to the effect of advanced aerodynamic, propulsion, structural and subsystem technologies on takeoff gross weight. A dramatic impact is noted to result from the combination of prospective technological advances in flow laminarization, advanced structures and materials, etc.

Study of Advanced Propulsion Systems for Small Transport Aircraft Technology (STAT) Program

NASA Technical Reports Server (NTRS)

Baerst, C. F.; Heldenbrand, R. W.; Rowse, J. H.

1981-01-01

Definitions of takeoff gross weight, performance, and direct operating cost for both a 30 and 50 passenger airplane were established. The results indicate that a potential direct operating cost benefit, resulting from advanced technologies, of approximately 20 percent would be achieved for the 1990 engines. Of the numerous design features that were evaluated, only maintenance-related items contributed to a significant decrease in direct operating cost. Recommendations are made to continue research and technology programs for advanced component and engine development.

Whole-body 3D kinematics of bird take-off: key role of the legs to propel the trunk

NASA Astrophysics Data System (ADS)

Provini, Pauline; Abourachid, Anick

2018-02-01

Previous studies showed that birds primarily use their hindlimbs to propel themselves into the air in order to take-off. Yet, it remains unclear how the different parts of their musculoskeletal system move to produce the necessary acceleration. To quantify the relative motions of the bones during the terrestrial phase of take-off, we used biplanar fluoroscopy in two species of birds, diamond dove ( Geopelia cuneata) and zebra finch ( Taeniopygia guttata). We obtained a detailed 3D kinematics analysis of the head, the trunk and the three long bones of the left leg. We found that the entire body assisted the production of the needed forces to take-off, during two distinct but complementary phases. The first one, a relatively slow preparatory phase, started with a movement of the head and an alignment of the different groups of bones with the future take-off direction. It was associated with a pitch down of the trunk and a flexion of the ankle, of the hip and, to a lesser extent, of the knee. This crouching movement could contribute to the loading of the leg muscles and store elastic energy that could be released in the propulsive phase of take-off, during the extension of the leg joints. Combined with the fact that the head, together with the trunk, produced a forward momentum, the entire body assisted the production of the needed forces to take-off. The second phase was faster with mostly horizontal forward and vertical upward translation motions, synchronous to an extension of the entire lower articulated musculoskeletal system. It led to the propulsion of the bird in the air with a fundamental role of the hip and ankle joints to move the trunk upward and forward. Take-off kinematics were similar in both studied species, with a more pronounced crouching movement in diamond dove, which can be related to a large body mass compared to zebra finch.

AVALON: definition and modeling of a vertical takeoff and landing UAV

NASA Astrophysics Data System (ADS)

Silva, N. B. F.; Marconato, E. A.; Branco, K. R. L. J. C.

2015-09-01

Unmanned Aerial Vehicles (UAVs) have been used in numerous applications, like remote sensing, precision agriculture and atmospheric data monitoring. Vertical takeoff and landing (VTOL) is a modality of these aircrafts, which are capable of taking off and landing vertically, like a helicopter. This paper presents the definition and modeling of a fixed- wing VTOL, named AVALON (Autonomous VerticAL takeOff and laNding), which has the advantages of traditional aircrafts with improved performance and can take off and land in small areas. The principles of small UAVs development were followed to achieve a better design and to increase the range of applications for this VTOL. Therefore, we present the design model of AVALON validated in a flight simulator and the results show its validity as a physical option for an UAV platform.

XB-70A during take-off

NASA Image and Video Library

1965-08-17

Viewed from the front the #1 XB-70A (62-0001) is shown climbing out during take-off. Most flights were scheduled during the morning hours to take advantage of the cooler ambient air temperatures for improved propulsion efficiencies. The wing tips are extended straight out to provide a maximum lifting wing surface. The XB-70A, capable of flying three times the speed of sound, was the world's largest experimental aircraft in the 1960s. Two XB-70A aircraft were built. Ship #1 was flown by NASA in a high speed flight research program.

Development of a takeoff performance monitoring system. Ph.D. Thesis. Contractor Report, Jan. 1984 - Jun. 1985

NASA Technical Reports Server (NTRS)

Srivatsan, Raghavachari; Downing, David R.

1987-01-01

Discussed are the development and testing of a real-time takeoff performance monitoring algorithm. The algorithm is made up of two segments: a pretakeoff segment and a real-time segment. One-time imputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data for that takeoff. The real-time segment uses the scheduled performance data generated in the pretakeoff segment, runway length data, and measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. An important feature of this algorithm is the one-time estimation of the runway rolling friction coefficient. The algorithm was tested using a six-degree-of-freedom airplane model in a computer simulation. Results from a series of sensitivity analyses are also included.

Low Noise Exhaust Nozzle Technology Development

NASA Technical Reports Server (NTRS)

Majjigi, R. K.; Balan, C.; Mengle, V.; Brausch, J. F.; Shin, H.; Askew, J. W.

2005-01-01

NASA and the U.S. aerospace industry have been assessing the economic viability and environmental acceptability of a second-generation supersonic civil transport, or High Speed Civil Transport (HSCT). Development of a propulsion system that satisfies strict airport noise regulations and provides high levels of cruise and transonic performance with adequate takeoff performance, at an acceptable weight, is critical to the success of any HSCT program. The principal objectives were to: 1. Develop a preliminary design of an innovative 2-D exhaust nozzle with the goal of meeting FAR36 Stage III noise levels and providing high levels of cruise performance with a high specific thrust for Mach 2.4 HSCT with a range of 5000 nmi and a payload of 51,900 lbm, 2. Employ advanced acoustic and aerodynamic codes during preliminary design, 3. Develop a comprehensive acoustic and aerodynamic database through scale-model testing of low-noise, high-performance, 2-D nozzle configurations, based on the preliminary design, and 4. Verify acoustic and aerodynamic predictions by means of scale-model testing. The results were: 1. The preliminary design of a 2-D, convergent/divergent suppressor ejector nozzle for a variable-cycle engine powered, Mach 2.4 HSCT was evolved, 2. Noise goals were predicted to be achievable for three takeoff scenarios, and 3. Impact of noise suppression, nozzle aerodynamic performance, and nozzle weight on HSCT takeoff gross weight were assessed.

Boeing-747 aircraft with external cargo pod

NASA Technical Reports Server (NTRS)

Quartero, C. B.; Washburn, G. F.; Price, J. E.

1978-01-01

An analysis was conducted to investigate the feasibility of mounting a detachable pod to the underside of the fuselage of a Boeing Model 747 aircraft to carry outsized cargo in case of military emergency. The analysis showed that the 747 configured with the pod and carrying only a bridge launcher as payload attained a range of 8.70 Mm (4 700 n. mi.) at Mach .68. This range was based on a maximum take-off gross weight of 3.447 MN (775 000 1bf) which included 212 kN (47 700 lbf) pod weight and 543 kN (122 000 lbf) payload (bridge launcher).

26 CFR 1.832-1 - Gross income.

Code of Federal Regulations, 2010 CFR

2010-04-01

... deposit premiums received, but not assessments, shall be excluded from gross income. Gross income does not... 26 Internal Revenue 8 2010-04-01 2010-04-01 false Gross income. 1.832-1 Section 1.832-1 Internal... TAXES Other Insurance Companies § 1.832-1 Gross income. (a) Gross income as defined in section 832(b)(1...

The Flight Optimization System Weights Estimation Method

NASA Technical Reports Server (NTRS)

Wells, Douglas P.; Horvath, Bryce L.; McCullers, Linwood A.

2017-01-01

FLOPS has been the primary aircraft synthesis software used by the Aeronautics Systems Analysis Branch at NASA Langley Research Center. It was created for rapid conceptual aircraft design and advanced technology impact assessments. FLOPS is a single computer program that includes weights estimation, aerodynamics estimation, engine cycle analysis, propulsion data scaling and interpolation, detailed mission performance analysis, takeoff and landing performance analysis, noise footprint estimation, and cost analysis. It is well known as a baseline and common denominator for aircraft design studies. FLOPS is capable of calibrating a model to known aircraft data, making it useful for new aircraft and modifications to existing aircraft. The weight estimation method in FLOPS is known to be of high fidelity for conventional tube with wing aircraft and a substantial amount of effort went into its development. This report serves as a comprehensive documentation of the FLOPS weight estimation method. The development process is presented with the weight estimation process.

Advanced Supersonic Technology concept AST-100 characteristics developed in a baseline-update study

NASA Technical Reports Server (NTRS)

Baber, H. T., Jr.; Swanson, E. E.

1976-01-01

The advanced supersonic technology configuration, AST-100, is described. The combination of wing thickness reduction, nacelle recontouring for minimum drag at cruise, and the use of the horizontal tail to produce lift during climb and cruise resulted in an increase in maximum lift-to-drag ratio. Lighter engines and lower fuel weight associated with this resizing result in a six percent reduction in takeoff gross weight. The AST-100 takeoff maximum effective perceived noise at the runway centerline and sideline measurement stations was 114.4 decibels. Since 1.5-decibels tradeoff is available from the approach noise, the required engine noise supression is 4.9 decibels. The AST-100 largest maximum overpressure would occur during transonic climb acceleration when the aircraft was at relatively low altitude. Calculated standard +8 C day range of the AST-100, with a 292 passenger payload, is 7348 km (3968 n.mi). Fuel price is the largest contributor to direct operating cost. However, if the AST-100 were flown subsonically (M = 0.9), direct operating costs would increase approximately 50 percent because of time related costs.

14 CFR 135.389 - Large nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... controlled in flight after an engine becomes inoperative) or 115 percent of the power off stalling speed in... assumed that takeoff power is used on all engines during the acceleration; (2) Not more than 50 percent of... be taken into account; (3) The average runway gradient (the difference between the elevations of the...

14 CFR 135.389 - Large nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... controlled in flight after an engine becomes inoperative) or 115 percent of the power off stalling speed in... assumed that takeoff power is used on all engines during the acceleration; (2) Not more than 50 percent of... be taken into account; (3) The average runway gradient (the difference between the elevations of the...

14 CFR 135.389 - Large nontransport category airplanes: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... controlled in flight after an engine becomes inoperative) or 115 percent of the power off stalling speed in... assumed that takeoff power is used on all engines during the acceleration; (2) Not more than 50 percent of... be taken into account; (3) The average runway gradient (the difference between the elevations of the...

Airport take-off noise assessment aimed at identify responsible aircraft classes.

PubMed

Sanchez-Perez, Luis A; Sanchez-Fernandez, Luis P; Shaout, Adnan; Suarez-Guerra, Sergio

2016-01-15

Assessment of aircraft noise is an important task of nowadays airports in order to fight environmental noise pollution given the recent discoveries on the exposure negative effects on human health. Noise monitoring and estimation around airports mostly use aircraft noise signals only for computing statistical indicators and depends on additional data sources so as to determine required inputs such as the aircraft class responsible for noise pollution. In this sense, the noise monitoring and estimation systems have been tried to improve by creating methods for obtaining more information from aircraft noise signals, especially real-time aircraft class recognition. Consequently, this paper proposes a multilayer neural-fuzzy model for aircraft class recognition based on take-off noise signal segmentation. It uses a fuzzy inference system to build a final response for each class p based on the aggregation of K parallel neural networks outputs Op(k) with respect to Linear Predictive Coding (LPC) features extracted from K adjacent signal segments. Based on extensive experiments over two databases with real-time take-off noise measurements, the proposed model performs better than other methods in literature, particularly when aircraft classes are strongly correlated to each other. A new strictly cross-checked database is introduced including more complex classes and real-time take-off noise measurements from modern aircrafts. The new model is at least 5% more accurate with respect to previous database and successfully classifies 87% of measurements in the new database. Copyright © 2015 Elsevier B.V. All rights reserved.

Simulation of homogeneous condensation of small polyatomic systems in high pressure supersonic nozzle flows using Bhatnagar-Gross-Krook model

NASA Astrophysics Data System (ADS)

Kumar, Rakesh; Levin, Deborah A.

2011-03-01

In the present work, we have simulated the homogeneous condensation of carbon dioxide and ethanol using the Bhatnagar-Gross-Krook based approach. In an earlier work of Gallagher-Rogers et al. [J. Thermophys. Heat Transfer 22, 695 (2008)], it was found that it was not possible to simulate condensation experiments of Wegener et al. [Phys. Fluids 15, 1869 (1972)] using the direct simulation Monte Carlo method. Therefore, in this work, we have used the statistical Bhatnagar-Gross-Krook approach, which was found to be numerically more efficient than direct simulation Monte Carlo method in our previous studies [Kumar et al., AIAA J. 48, 1531 (2010)], to model homogeneous condensation of two small polyatomic systems, carbon dioxide and ethanol. A new weighting scheme is developed in the Bhatnagar-Gross-Krook framework to reduce the computational load associated with the study of homogeneous condensation flows. The solutions obtained by the use of the new scheme are compared with those obtained by the baseline Bhatnagar-Gross-Krook condensation model (without the species weighting scheme) for the condensing flow of carbon dioxide in the stagnation pressure range of 1-5 bars. Use of the new weighting scheme in the present work makes the simulation of homogeneous condensation of ethanol possible. We obtain good agreement between our simulated predictions for homogeneous condensation of ethanol and experiments in terms of the point of condensation onset and the distribution of mass fraction of ethanol condensed along the nozzle centerline.

Rocket-based combined-cycle (RBCC) powered spaceliner class vehicle can advantageously employ vertical takeoff and landing (VTOL)

NASA Technical Reports Server (NTRS)

Escher, William J. D.

1995-01-01

The subject is next generation orbital space transporation, taken to be fully reusable non-staged 'aircraft like' systems targeted for routine, affordable access to space. Specifically, the takeoff and landing approach to be selected for such systems is considered, mainly from a propulsion viewpoint. Conventional wisdom has it that any transatmospheric-class vehicle which uses high-speed airbreathing propulsion modes (e.g., scramjet) intrinsically must utilize horizontal takeoff and landing, HTOHL. Although this may be true for all-airbreathing propulsion (i.e., no rocket content as in turboramjet propulsion), that emerging class of powerplant which integrally combines airbreathing and rocket propulsion, referred to as rocket-based combined-cycle (RBCC) propulsion, is considerably more flexible with respect to selecting takeoff/landing modes. In fact, it is proposed that any of the modes of interest may potentially be selected: HTOHL, VTOHL, VTOVL. To illustrate this surmise, the case of a previously documented RBCC-powered 'Spaceliner' class space transport concept, which is designed for vertical takeoff and landing, is examined. The 'RBCC' and 'Spaceliner' categories are first described for background. Departing form an often presumed HTOHL baseline, the leading design and operational advantages of moving to VTOVL are then elucidated. Technical substantiation that the RBCC approach, in fact, enables this capability (but also that of HTOHL and VTOVL) is provided, with extensive reference to case-in-point supporting studies. The paper closes with a set of conditional surmises bearing on its set of conclusions, which point up the operational cost advantages associated with selecting the vertical takeoff and landing mode combination (VTOL), uniquely offered by RBCC propulsion.

Rocket-based combined-cycle (RBCC) powered spaceliner class vehicle can advantageously employ vertical takeoff and landing (VTOL)

NASA Astrophysics Data System (ADS)

Escher, William J. D.

The subject is next generation orbital space transporation, taken to be fully reusable non-staged 'aircraft like' systems targeted for routine, affordable access to space. Specifically, the takeoff and landing approach to be selected for such systems is considered, mainly from a propulsion viewpoint. Conventional wisdom has it that any transatmospheric-class vehicle which uses high-speed airbreathing propulsion modes (e.g., scramjet) intrinsically must utilize horizontal takeoff and landing, HTOHL. Although this may be true for all-airbreathing propulsion (i.e., no rocket content as in turboramjet propulsion), that emerging class of powerplant which integrally combines airbreathing and rocket propulsion, referred to as rocket-based combined-cycle (RBCC) propulsion, is considerably more flexible with respect to selecting takeoff/landing modes. In fact, it is proposed that any of the modes of interest may potentially be selected: HTOHL, VTOHL, VTOVL. To illustrate this surmise, the case of a previously documented RBCC-powered 'Spaceliner' class space transport concept, which is designed for vertical takeoff and landing, is examined. The 'RBCC' and 'Spaceliner' categories are first described for background. Departing form an often presumed HTOHL baseline, the leading design and operational advantages of moving to VTOVL are then elucidated. Technical substantiation that the RBCC approach, in fact, enables this capability (but also that of HTOHL and VTOVL) is provided, with extensive reference to case-in-point supporting studies. The paper closes with a set of conditional surmises bearing on its set of conclusions, which point up the operational cost advantages associated with selecting the vertical takeoff and landing mode combination (VTOL), uniquely offered by RBCC propulsion.

Comparison of motor development of low birth weight (LBW) infants with and without using mechanical ventilation and normal birth weight infants

PubMed Central

Nazi, Sepideh; Aliabadi, Faranak

2015-01-01

Background: To determine whether using mechanical ventilation in neonatal intensive care unit (NICU) influences motor development of low birth weight (LBW) infants and to compare their motor development with normal birth weight (NBW) infants at the age of 8 to 12 months using Peabody Developmental Motor Scale 2 (PDMS-2). Methods: This cross sectional study was conducted on 70 LBW infants in two groups, mechanical ventilation (MV) group, n=35 and without mechanical ventilation (WMV) group, n=35 and 40 healthy NBW infants matched with LBW group for age. Motor quotients were determined using PDMS-2 and compared in all groups using ANOVA statistical method and SPSS version 17. Results: Comparison of the mean developmental motor quotient (DMQ) of both MV and WMV groups showed significant differences with NBW group (p< 0.05). Also, significant difference was found between the gross DMQ of MV group and WMV group (p< 0.05). Moreover, in MV group, both gross and fine motor quotients were considered as below average (16.12%). In WMV group, the gross motor quotient was considered as average (49.51%) and the fine motor quotient was considered as below average (16.12%). Conclusion: It seems that LBW infants have poor fine motor outcomes. The gross motor outcomes, on the other hand, will be significantly more influenced by using mechanical ventilation. In addition, more differences seem to be related to lower birth weight. Very Low Birth Weight (VLBW) infants are more prone to developmental difficulties than LBW infants with the history of using mechanical ventilation especially in fine motor development. PMID:26913264

Performance of arrays of direct-driven wave energy converters under optimal power take-off damping

NASA Astrophysics Data System (ADS)

Wang, Liguo; Engström, Jens; Leijon, Mats; Isberg, Jan

2016-08-01

It is well known that the total power converted by a wave energy farm is influenced by the hydrodynamic interactions between wave energy converters, especially when they are close to each other. Therefore, to improve the performance of a wave energy farm, the hydrodynamic interaction between converters must be considered, which can be influenced by the power take-off damping of individual converters. In this paper, the performance of arrays of wave energy converters under optimal hydrodynamic interaction and power take-off damping is investigated. This is achieved by coordinating the power take-off damping of individual converters, resulting in optimal hydrodynamic interaction as well as higher production of time-averaged power converted by the farm. Physical constraints on motion amplitudes are considered in the solution, which is required for the practical implementation of wave energy converters. Results indicate that the natural frequency of a wave energy converter under optimal damping will not vary with sea states, but the production performance of a wave energy farm can be improved significantly while satisfying the motion constraints.

Hydrodynamic Qualities of a 1/10-Size Powered Dynamic Model of the XP5Y-1 Flying Boat in Smooth Water: Langley Tank Model 246, TED No. NACA DE 320

NASA Technical Reports Server (NTRS)

Woodward, David R.; Weinstein, Irving; Whitaker, Walter E., Jr.

1947-01-01

The hydrodynamic characteristics of a 1/10-size powered dynamic model of the XP5Y-1 flying boat were determined in Langley tank no. 1. Stable take-offs were possible at all practicable positions of the center of gravity and flap deflections. An increase in gross load from 123.5 to 150.0 pounds (21.5 percent) had only a slight effect on the stable range for take-off. A decrease in forward acceleration from 3.0 to 1.0 feet per second per second had only a very small effect on the stable range for take-off. In general, the landings were free from skipping except at trims below 6 deg where one skip was encountered at an aft position of the center of gravity. The model porpoised during the landing runout at all positions of the center of gravity when landed at trims above 10 deg. Spray in the propellers was light at the design gross load, and was not considered excessive,at a gross load of 136.0 pounds.

General aviation accidents related to exceedance of airplane weight/center of gravity limits.

PubMed

Boyd, Douglas D

2016-06-01

Obesity, affects a third of the US population and its corollary occupant weight adversely impacts safe flight operations. Increased aircraft weight results in longer takeoff/landing distances, degraded climb gradients and airframe failure may occur in turbulence. In this study, the rate, temporal changes, and lethality of accidents in piston-powered, general aviation aircraft related to exceeding the maximum aircraft weight/center of gravity (CG) limits were determined. Nation-wide person body mass were from the National Health and Nutrition Examination Survey. The NTSB database was used to identify accidents related to operation of aircraft outside of their weight/CG envelope. Statistical analyses employed T-tests, proportion tests and a Poisson distribution. While the average body mass climbed steadily (p<0.001) between 1999 and 2014 the rate of accidents related to exceedance of the weight/CG limits did not change (p=0.072). However, 57% were fatal, higher (p<0.001) than the 21% for mishaps attributed to other causes/factors. The majority (77%) of accidents were due to an overloaded aircraft operating within its CG limits. As to the phase of flight, accidents during takeoff and those occurring enroute carried the lowest (50%) and highest (85%) proportion of fatal accidents respectively. While the rate of general aviation accidents related to operating an aircraft outside of its weight/CG envelope has not increased over the past 15 years, these types of accidents carry a high risk of fatality. Airmen should be educated as to such risks and to dispel the notion held by some that flights may be safely conducted with an overloaded aircraft within its CG limits. Copyright © 2016 Elsevier Ltd. All rights reserved.

RFB research and development in WIG vehicles

NASA Astrophysics Data System (ADS)

Fischer, Hanno

An account is given of the development history of wing-in-ground (WIG) effect aircraft at a major West German aircraft manufacturer since 1964; these efforts have encompassed the development of the X113 and X114 'airfoilboat' WIG seaplanes. Attention is given to the aerodynamic efficiency and operational economy trends that result from up-scaling of WIG craft configurations to takeoff gross weights of the order of 300 tons. Also noted is the illustration of comparative efficiency among types of transportation, including WIG vehicles, given by the von Karman-Gabrielli diagram.

A technique for integrating engine cycle and aircraft configuration optimization

NASA Technical Reports Server (NTRS)

Geiselhart, Karl A.

1994-01-01

A method for conceptual aircraft design that incorporates the optimization of major engine design variables for a variety of cycle types was developed. The methodology should improve the lengthy screening process currently involved in selecting an appropriate engine cycle for a given application or mission. The new capability will allow environmental concerns such as airport noise and emissions to be addressed early in the design process. The ability to rapidly perform optimization and parametric variations using both engine cycle and aircraft design variables, and to see the impact on the aircraft, should provide insight and guidance for more detailed studies. A brief description of the aircraft performance and mission analysis program and the engine cycle analysis program that were used is given. A new method of predicting propulsion system weight and dimensions using thermodynamic cycle data, preliminary design, and semi-empirical techniques is introduced. Propulsion system performance and weights data generated by the program are compared with industry data and data generated using well established codes. The ability of the optimization techniques to locate an optimum is demonstrated and some of the problems that had to be solved to accomplish this are illustrated. Results from the application of the program to the analysis of three supersonic transport concepts installed with mixed flow turbofans are presented. The results from the application to a Mach 2.4, 5000 n.mi. transport indicate that the optimum bypass ratio is near 0.45 with less than 1 percent variation in minimum gross weight for bypass ratios ranging from 0.3 to 0.6. In the final application of the program, a low sonic boom fix a takeoff gross weight concept that would fly at Mach 2.0 overwater and at Mach 1.6 overland is compared with a baseline concept of the same takeoff gross weight that would fly Mach 2.4 overwater and subsonically overland. The results indicate that for the design mission

26 CFR 1.61-1 - Gross income.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Gross income. 1.61-1 Section 1.61-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Definition of Gross Income, Adjusted Gross Income, and Taxable Income § 1.61-1 Gross...

Ready for Takeoff: China’s Advancing Aerospace Industry

DTIC Science & Technology

2011-01-01

designed to study the effects of radiation and microgravity on different varieties of fruit and vegetable seeds, fungi , and molecular biomaterials. No...negatively affect U.S. interests and would increase the costs—human and material—of resisting such force. xiv Ready for Takeoff: China’s Advancing...summarizes projec- tions of its future growth, and analyzes factors that are likely to affect that growth, such as the availability of high-speed rail

NASA KingAir #801 during takeoff

NASA Technical Reports Server (NTRS)

1999-01-01

NASA KingAir N801NA during takeoff. The Beechcraft Beech 200 Super KingAir aircraft N7NA, known as NASA 7, has been a support aircraft for many years, flying 'shuttle' missions to Ames Research Center. It once flew from the Jet Propulsion Laboratory and back each day but now (2001) flies between the Dryden Flight Research Center and Ames. Dryden assumed the mission and aircraft in September 1996. A second Beechcraft Beech 200 Super King Air, N701NA, redesignated N801NA, transferred to Dryden on 3 Oct. 1997 and is used for research missions but substitutes for NASA 7 on shuttle missions when NASA 7 is not available.

Generation of the pitch moment during the controlled flight after takeoff of fruitflies.

PubMed

Chen, Mao Wei; Wu, Jiang Hao; Sun, Mao

2017-01-01

In the present paper, the controlled flight of fruitflies after voluntary takeoff is studied. Wing and body kinematics of the insects after takeoff are measured using high-speed video techniques, and the aerodynamic force and moment are calculated by the computational fluid dynamics method based on the measured data. How the control moments are generated is analyzed by correlating the computed moments with the wing kinematics. A fruit-fly has a large pitch-up angular velocity owing to the takeoff jump and the fly controls its body attitude by producing pitching moments. It is found that the pitching moment is produced by changes in both the aerodynamic force and the moment arm. The change in the aerodynamic force is mainly due to the change in angle of attack. The change in the moment arm is mainly due to the change in the mean stroke angle and deviation angle, and the deviation angle plays a more important role than the mean stroke angle in changing the moment arm (note that change in deviation angle implies variation in the position of the aerodynamic stroke plane with respect to the anatomical stroke plane). This is unlike the case of fruitflies correcting pitch perturbations in steady free flight, where they produce pitching moment mainly by changes in mean stroke angle.

NACA Photographer North American F-100A (NACA-200) Super Sabre Airplane take-off. The blowing-tupe

NASA Technical Reports Server (NTRS)

1957-01-01

NACA Photographer North American F-100A (NACA-200) Super Sabre Airplane take-off. The blowing-tupe boundary-layer control on the leading- and trailing-edge provided large reductions in takeoff and landing approach speeds. Approach speeds were reduced by about 10 knots (Mar 1960). Note: Used in publication in Flight Research at Ames; 57 Years of Development and Validation of Aeronautical Technology NASA SP-1998-3300 fig. 102 and and Memoirs of a Flight Test Engneer NASA SP-2002-4525

Issues related to aircraft take-off plumes in a mesoscale photochemical model.

PubMed

Bossioli, Elissavet; Tombrou, Maria; Helmis, Costas; Kurtenbach, Ralf; Wiesen, Peter; Schäfer, Klaus; Dandou, Aggeliki; Varotsos, Kostas V

2013-07-01

The physical and chemical characteristics of aircraft plumes at the take-off phase are simulated with the mesoscale CAMx model using the individual plume segment approach, in a highly resolved domain, covering the Athens International Airport. Emission indices during take-off measured at the Athens International Airport are incorporated. Model predictions are compared with in situ point and path-averaged observations (NO, NO₂) downwind of the runway at the ground. The influence of modeling process, dispersion properties and background air composition on the chemical evolution of the aircraft plumes is examined. It is proven that the mixing properties mainly determine the plume dispersion. The initial plume properties become significant for the selection of the appropriate vertical resolution. Besides these factors, the background NOx and O₃ concentration levels control NOx distribution and their conversion to nitrogen reservoir species. Copyright © 2013 Elsevier B.V. All rights reserved.

Integrated Flight-propulsion Control Concepts for Supersonic Transport Airplanes

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Gilyard, Glenn B.; Gelhausen, Paul A.

1990-01-01

Integration of propulsion and flight control systems will provide significant performance improvements for supersonic transport airplanes. Increased engine thrust and reduced fuel consumption can be obtained by controlling engine stall margin as a function of flight and engine operating conditions. Improved inlet pressure recovery and decreased inlet drag can result from inlet control system integration. Using propulsion system forces and moments to augment the flight control system and airplane stability can reduce the flight control surface and tail size, weight, and drag. Special control modes may also be desirable for minimizing community noise and for emergency procedures. The overall impact of integrated controls on the takeoff gross weight for a generic high speed civil transport is presented.

Take-off analysis of the Olympic ski jumping competition (HS-106m).

PubMed

Virmavirta, Mikko; Isolehto, Juha; Komi, Paavo; Schwameder, Hermann; Pigozzi, Fabio; Massazza, Giuseppe

2009-05-29

The take-off phase (approximately 6m) of the jumps of all athletes participating in the individual HS-106m hill ski jumping competition at the Torino Olympics was filmed with two high-speed cameras. The high altitude of the Pragelato ski jumping venue (1600m) and slight tail wind in the final jumping round were expected to affect the results of this competition. The most significant correlation with the length of the jump was found in the in-run velocity (r=0.628, p<0.001, n=50). This was a surprise in Olympic level ski jumping, and suggests that good jumpers simply had smaller friction between their skis and the in-run tracks and/or the aerodynamic quality of their in-run position was better. Angular velocity of the hip joint of the best jumpers was also correlated with jumping distance (r=0.651, p<0.05, n=10). The best jumpers in this competition exhibited very different take-off techniques, but still they jumped approximately the same distance. This certainly improves the interests in ski jumping among athletes and spectators. The comparison between the take-off techniques of the best jumpers showed that even though the more marked upper body movement creates higher air resistance, it does not necessarily result in shorter jumping distance if the exposure time to high air resistance is not too long. A comparison between the first and second round jumps of the same jumpers showed that the final results in this competition were at least partly affected by the wind conditions.

77 FR 56764 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-14

... August 31, 2012. Ray Towles, Deputy Director, Flight Standards Service. Adoption of the Amendment... Muni, RNAV (GPS) RWY 36, Amdt 1 Mountain View, CA, Moffett Federal Airfield, Takeoff Minimums and...

Gross Morphometric Studies on the Tongue, Buccal Cavity and Hard Palate of the Fruit Bat (Eidolon helvum).

PubMed

Igado, O O; Omobowale, T O; Ajadi, R A; Nottidge, H O

2015-08-01

This study was designed to assess the gross morphometric studies of the tongue, hard palate and buccal cavity of the fruit bat (Eidolon helvum). Sixty bats of both sexes were used for this study. The tongue was excised, and the weight and various linear measurements were determined. Linear measurements were also determined on the hard palate. The gross distribution of the lingual papillae was observed to be the same in both sexes; values obtained for the weight and length of the tongue were higher in the females, although no statistically significant differences were observed (P > 0.05). The number of ridges on the hard palate displayed sexual dimorphism. Results obtained from this study may find application in the field of comparative and clinical anatomy of wildlife and also in feeding physiology. © 2014 Blackwell Verlag GmbH.

77 FR 42627 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-20

... CONTACT: Richard A. Dunham III, Flight Procedure Standards Branch (AFS-420), Flight Technologies and... 2012 Red Cloud, NE., Red Cloud Muni, Takeoff Minimums and Obstacle DP, Orig Effective 23 AUGUST 2012...

A Mathematical Model for Vertical Attitude Takeoff and Landing (VATOL) Aircraft Simulation. Volume 1; Model Description Application

NASA Technical Reports Server (NTRS)

Fortenbaugh, R. L.

1980-01-01

A mathematical model of a high performance airplane capable of vertical attitude takeoff and landing (VATOL) was developed. An off line digital simulation program incorporating this model was developed to provide trim conditions and dynamic check runs for the piloted simulation studies and support dynamic analyses of proposed VATOL configuration and flight control concepts. Development details for the various simulation component models and the application of the off line simulation program, Vertical Attitude Take-Off and Landing Simulation (VATLAS), to develop a baseline control system for the Vought SF-121 VATOL airplane concept are described.

Strapdown system redundancy management flight demonstration. [vertical takeoff and landing aircraft

NASA Technical Reports Server (NTRS)

1978-01-01

The suitability of strapdown inertial systems in providing highly reliable short-term navigation for vertical take-off and landing (VTOL) aircraft operating in an intra-urban setting under all-weather conditions was assessed. A preliminary design configuration of a skewed sensor inertial reference system employing a redundancy management concept to achieve fail-operational, fail-operational performance, was developed.

Innovative procedure for the determination of gross-alpha/gross-beta activities in drinking water.

PubMed

Wisser, S; Frenzel, E; Dittmer, M

2006-03-01

An alternative sample preparation method for the determination of gross-alpha/beta activity concentrations in drinking water is introduced in this paper. After the freeze-drying of tap water samples, determination by liquid scintillation counting can be applied utilizing alpha/beta separation. It has been shown that there is no adsorption or loss of solid radionuclides during the freeze-drying procedure. However, the samples have to be measured quickly after the preparation since the ingrowth of daughter isotopes negatively effects the measurement. The limits of detection for gross-alpha and gross-beta activity are in the range 25-210 mBq/l, respectively, for a measurement time of only 8-9 h.

77 FR 50014 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-20

... navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed.... Intl. 20-Sep-12 TX Houston Sugar Land Rgnl.... 2/8058 7/19/12 TAKEOFF MINIMUMS AND (OBSTACLE) DP, Amdt...

75 FR 25760 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-10

..., ME, Wiscasset, Takeoff Minimums and Obstacle DP, Amdt 2 Alpena, MI, Alpena County Rgnl, RNAV (GPS) RWY 19, Orig Alpena, MI, Alpena County Rgnl, VOR RWY 19, Amdt 15 Oscoda, MI, Oscoda-Wurtsmith, RNAV...

76 FR 25232 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... Patterson, LA, Harry P Williams Memorial, NDB RWY 6, Amdt 11 Slidell, LA, Slidell, Takeoff Minimums and... Harrisonville, MO, Lawrence Smith Memorial, VOR/DME RWY 35, Orig-A, CANCELLED Lincoln Park, NJ, Lincoln Park...

14 CFR 135.367 - Large transport category airplanes: Reciprocating engine powered: Takeoff limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Large transport category airplanes... AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.367 Large transport category airplanes: Reciprocating engine powered: Takeoff limitations. (a) No...

14 CFR 135.367 - Large transport category airplanes: Reciprocating engine powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes... AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.367 Large transport category airplanes: Reciprocating engine powered: Takeoff limitations. (a) No...

14 CFR 135.367 - Large transport category airplanes: Reciprocating engine powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes... AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.367 Large transport category airplanes: Reciprocating engine powered: Takeoff limitations. (a) No...

14 CFR 135.367 - Large transport category airplanes: Reciprocating engine powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes... AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.367 Large transport category airplanes: Reciprocating engine powered: Takeoff limitations. (a) No...

14 CFR 135.367 - Large transport category airplanes: Reciprocating engine powered: Takeoff limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Large transport category airplanes... AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.367 Large transport category airplanes: Reciprocating engine powered: Takeoff limitations. (a) No...

77 FR 37799 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-25

..., individual SIAP and Takeoff Minimums and ODP copies may be obtained from: 1. FAA Public Inquiry Center (APA... number of SIAPs, their complex nature, and the need for a special format make their verbatim publication...

A preliminary study of the performance and characteristics of a supersonic executive aircraft

NASA Technical Reports Server (NTRS)

Mascitti, V. R.

1977-01-01

The impact of advanced supersonic technologies on the performance and characteristics of a supersonic executive aircraft was studied in four configurations with different engine locations and wing/body blending and an advanced nonafterburning turbojet or variable cycle engine. An M 2.2 design Douglas scaled arrow-wing was used with Learjet 35 accommodations. All four configurations with turbojet engines meet the performance goals of 5926 km (3200 n.mi.) range, 1981 meters (6500 feet) takeoff field length, and 77 meters per second (150 knots) approach speed. The noise levels of of turbojet configurations studied are excessive. However, a turbojet with mechanical suppressor was not studied. The variable cycle engine configuration is deficient in range by 555 km (300 n.mi) but nearly meets subsonic noise rules (FAR 36 1977 edition), if coannular noise relief is assumed. All configurations are in the 33566 to 36287 kg (74,000 to 80,000 lbm) takeoff gross weight class when incorporating current titanium manufacturing technology.

Hydrodynamic and Aerodynamic Characteristics of a Model of a Supersonic Multijet Water-Based Aircraft Equipped with Supercavitating Hydrofoils

NASA Technical Reports Server (NTRS)

McKann, Robert E.; Blanchard, Ulysse J.; Pearson, Albin O.

1960-01-01

The hydrodynamic and aerodynamic characteristics of a model of a multijet water-based Mach 2.0 aircraft equipped with hydrofoils have been determined. Takeoff stability and spray characteristics were very good, and sufficient excess thrust was available for takeoff in approximately 32 seconds and 4,700 feet at a gross weight of 225,000 pounds. Longitudinal and lateral stability during smooth-water landings were good. Lateral stability was good during rough-water landings, but forward location of the hydrofoils or added pitch damping was required to prevent diving. Hydrofoils were found to increase the aerodynamic lift-curve slope and to increase the aerodynamic drag coefficient in the transonic speed range, and the maximum lift-drag ratio decreased from 7.6 to 7.2 at the cruise Mach number of 0.9. The hydrofoils provided an increment of positive pitching moment over the Mach number range of the tests (0.6 to 1.42) and reduced the effective dihedral and directional stability.

An Analytical Study for Subsonic Oblique Wing Transport Concept

NASA Technical Reports Server (NTRS)

Bradley, E. S.; Honrath, J.; Tomlin, K. H.; Swift, G.; Shumpert, P.; Warnock, W.

1976-01-01

The oblique wing concept has been investigated for subsonic transport application for a cruise Mach number of 0.95. Three different mission applications were considered and the concept analyzed against the selected mission requirements. Configuration studies determined the best area of applicability to be a commercial passenger transport mission. The critical parameter for the oblique wing concept was found to be aspect ratio which was limited to a value of 6.0 due to aeroelastic divergence. Comparison of the concept final configuration was made with fixed winged configurations designed to cruise at Mach 0.85 and 0.95. The crossover Mach number for the oblique wing concept was found to be Mach 0.91 for takeoff gross weight and direct operating cost. Benefits include reduced takeoff distance, installed thrust and mission block fuel and improved community noise characteristics. The variable geometry feature enables the final configuration to increase range by 10% at Mach 0.712 and to increase endurance by as much as 44%.

Simultaneous determination of gross alpha, gross beta and ²²⁶Ra in natural water by liquid scintillation counting.

PubMed

Fons, J; Zapata-García, D; Tent, J; Llauradó, M

2013-11-01

The determination of gross alpha, gross beta and (226)Ra activity in natural waters is useful in a wide range of environmental studies. Furthermore, gross alpha and gross beta parameters are included in international legislation on the quality of drinking water [Council Directive 98/83/EC]. In this work, a low-background liquid scintillation counter (Wallac, Quantulus 1220) was used to simultaneously determine gross alpha, gross beta and (226)Ra activity in natural water samples. Sample preparation involved evaporation to remove (222)Rn and its short-lived decay daughters. The evaporation process concentrated the sample ten-fold. Afterwards, a sample aliquot of 8 mL was mixed with 12 mL of Ultima Gold AB scintillation cocktail in low-diffusion vials. In this study, a theoretical mathematical model based on secular equilibrium conditions between (226)Ra and its short-lived decay daughters is presented. The proposed model makes it possible to determine (226)Ra activity from two measurements. These measurements also allow determining gross alpha and gross beta simultaneously. To validate the proposed model, spiked samples with different activity levels for each parameter were analysed. Additionally, to evaluate the model's applicability in natural water, eight natural water samples from different parts of Spain were analysed. The eight natural water samples were also characterised by alpha spectrometry for the naturally occurring isotopes of uranium ((234)U, (235)U and (238)U), radium ((224)Ra and (226)Ra), (210)Po and (232)Th. The results for gross alpha and (226)Ra activity were compared with alpha spectrometry characterization, and an acceptable concordance was obtained. Copyright © 2013 Elsevier Ltd. All rights reserved.

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Large transport category airplanes: Turbine... PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.379 Large transport category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine...

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Large transport category airplanes: Turbine... PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.379 Large transport category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine...

14 CFR 135.379 - Large transport category airplanes: Turbine engine powered: Takeoff limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Large transport category airplanes: Turbine... PERSONS ON BOARD SUCH AIRCRAFT Airplane Performance Operating Limitations § 135.379 Large transport category airplanes: Turbine engine powered: Takeoff limitations. (a) No person operating a turbine engine...

26 CFR 1.809-4 - Gross amount.

Code of Federal Regulations, 2010 CFR

2010-04-01

... categories of items taken into account are: (1) Premiums. (i) The gross amount of all premiums and other... premiums and premiums and other consideration arising out of reinsurance ceded. The term gross amount of... 26 Internal Revenue 8 2010-04-01 2010-04-01 false Gross amount. 1.809-4 Section 1.809-4 Internal...

26 CFR 1.832-4 - Gross income.

Code of Federal Regulations, 2013 CFR

2013-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-4 Gross income. (a)(1) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in section 831(a... gross income. Section 832(b)(1)(D) provides that in the case of a mutual fire or flood insurance company...

26 CFR 1.832-4 - Gross income.

Code of Federal Regulations, 2011 CFR

2011-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-4 Gross income. (a)(1) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in section 831(a... gross income. Section 832(b)(1)(D) provides that in the case of a mutual fire or flood insurance company...

26 CFR 1.832-4 - Gross income.

Code of Federal Regulations, 2012 CFR

2012-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-4 Gross income. (a)(1) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in section 831(a... gross income. Section 832(b)(1)(D) provides that in the case of a mutual fire or flood insurance company...

26 CFR 1.832-4 - Gross income.

Code of Federal Regulations, 2014 CFR

2014-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-4 Gross income. (a)(1) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in section 831(a... gross income. Section 832(b)(1)(D) provides that in the case of a mutual fire or flood insurance company...

77 FR 71495 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-03

..., Butler Memorial, VOR-A, Amdt 5 Deer Lodge, MT, Deer Lodge-City-County, RNAV (GPS)-A, Orig Deer Lodge, MT, Deer Lodge-City-County, Takeoff Minimums and Obstacle DP, Orig Mount Olive, NC, Mount Olive Muni, VOR-A...

Spontaneous movements of preterm infants is associated with outcome of gross motor development.

PubMed

Miyagishima, Saori; Asaka, Tadayoshi; Kamatsuka, Kaori; Kozuka, Naoki; Kobayashi, Masaki; Igarashi, Lisa; Hori, Tsukasa; Tsutsumi, Hiroyuki

2018-04-30

We conducted a longitudinal cohort study to analyze the relationship between outcome of gross motor development in preterm infants and factors that might affect their development. Preterm infants with a birth weight of <1500 g were recruited. We measured spontaneous antigravity limbs movements by 3D motion capture system at 3 months corrected age. Gross motor developmental outcomes at 6 and 12 months corrected age were evaluated using the Alberta Infant Motor Scale (AIMS). Statistical analysis was carried out by canonical correlation analysis. Eighteen preterm infants were included. In the 6 months corrected age analysis, spontaneous movement had a major effect on Prone and Sitting at 6 months corrected age of AIMS. In the 12 months corrected age analysis, spontaneous movement had a major effect on Sitting and Standing at 12 months corrected age of AIMS. In preterm infants, better antigravity spontaneous movements at 3 months corrected age were significantly correlated with better gross motor development at 6 or 12 months corrected age. Copyright © 2018 The Japanese Society of Child Neurology. Published by Elsevier B.V. All rights reserved.

Concurrent Validity of Preschooler Gross Motor Quality Scale with Test of Gross Motor Development-2

ERIC Educational Resources Information Center

Sun, Shih-Heng; Sun, Hsiao-Ling; Zhu, Yi-Ching; Huang, Li-chi; Hsieh, Yueh-Ling

2011-01-01

Preschooler Gross Motor Quality Scale (PGMQ) was recently developed to evaluate motor skill quality of preschoolers. The purpose of this study was to establish the concurrent validity of PGMQ using Test of Gross Motor Development-2 (TGMD-2) as the gold standard. One hundred and thirty five preschool children aged from three to six years were…

Requirements report for SSTO vertical take-off and horizontal landing vehicle

NASA Technical Reports Server (NTRS)

Greenberg, H. S.

1994-01-01

This document describes the detailed design requirements and design criteria to support Structures/TPS Technology development for SSTO winged vehicle configurations that use vertical take-off and horizontal landing and delivers 25,000 lb payloads to a 220 nm circular orbit at an inclination of 51.6 degrees or 40,000 lb payloads to a 150 nm circular orbit at a 28.5 degree inclination.

RSRA vertical drag test report. [rotor systems research aircraft

NASA Technical Reports Server (NTRS)

Flemming, R. J.

1981-01-01

The Rotor Systems Research Aircraft (RSRA), because of its ability to measure rotor loads, was used to conduct an experiment to determine vertical drag, tail rotor blockage, and thrust augmentation as affected by ground clearance and flight velocity. The RSRA was flown in the helicopter configuration at speeds from 0 to 15 knots for wheel heights from 5 to 150 feet, and to 60 knots out of ground effect. The vertical drag trends in hover, predicted by theory and shown in model tests, were generally confirmed. The OGE hover vertical drag is 4.0 percent, 1.1 percent greater than predicted. The vertical drag decreases rapidly as wheel height is reduced, and is zero at a wheel height of 6 feet. The vertical drag also decreases with forward speed, approaching zero at sixty knots. The test data show the effect of wheel height and forward speed on thrust, gross weight capability, and power, and provide the relationships for power and collective pitch at constant gross weight required for the simulation of helicopter takeoffs and landings.

Power-to-load balancing for asymmetric heave wave energy converters with nonideal power take-off

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tom, Nathan M.; Madhi, Farshad; Yeung, Ronald W.

The aim of this study is to maximize the power-to-load ratio for asymmetric heave wave energy converters. Linear hydrodynamic theory was used to calculate bounds of the expected time-averaged power (TAP) and corresponding surge-restraining force, pitch-restraining torque, and power take-off (PTO) control force with the assumption of sinusoidal displacement. This paper formulates an optimal control problem to handle an objective function with competing terms in an attempt to maximize power capture while minimizing structural and actuator loads in regular and irregular waves. Penalty weights are placed on the surge-restraining force, pitch-restraining torque, and PTO actuation force, thereby allowing the controlmore » focus to concentrate on either power absorption or load mitigation. The penalty weights are used to control peak structural and actuator loads that were found to curb the additional losses in power absorption associated with a nonideal PTO. Thus, in achieving these goals, a per-unit gain in TAP would not lead to a greater per-unit demand in structural strength, hence yielding a favorable benefit-to-cost ratio. Demonstrative results for 'The Berkeley Wedge' in the form of output TAP, reactive TAP needed to drive WEC motion, and the amplitudes of the surge-restraining force, pitch-restraining torque, and PTO control force are shown.« less

Power-to-load balancing for asymmetric heave wave energy converters with nonideal power take-off

DOE PAGES

Tom, Nathan M.; Madhi, Farshad; Yeung, Ronald W.

2017-12-11

The aim of this study is to maximize the power-to-load ratio for asymmetric heave wave energy converters. Linear hydrodynamic theory was used to calculate bounds of the expected time-averaged power (TAP) and corresponding surge-restraining force, pitch-restraining torque, and power take-off (PTO) control force with the assumption of sinusoidal displacement. This paper formulates an optimal control problem to handle an objective function with competing terms in an attempt to maximize power capture while minimizing structural and actuator loads in regular and irregular waves. Penalty weights are placed on the surge-restraining force, pitch-restraining torque, and PTO actuation force, thereby allowing the controlmore » focus to concentrate on either power absorption or load mitigation. The penalty weights are used to control peak structural and actuator loads that were found to curb the additional losses in power absorption associated with a nonideal PTO. Thus, in achieving these goals, a per-unit gain in TAP would not lead to a greater per-unit demand in structural strength, hence yielding a favorable benefit-to-cost ratio. Demonstrative results for 'The Berkeley Wedge' in the form of output TAP, reactive TAP needed to drive WEC motion, and the amplitudes of the surge-restraining force, pitch-restraining torque, and PTO control force are shown.« less

Ludwik Gross, Sarah Stewart, and the 1950s discoveries of Gross murine leukemia virus and polyoma virus.

PubMed

Morgan, Gregory J

2014-12-01

The Polish-American scientist Ludwik Gross made two important discoveries in the early 1950s. He showed that two viruses - murine leukemia virus and parotid tumor virus - could cause cancer when they were injected into susceptible animals. At first, Gross's discoveries were greeted with skepticism: it seemed implausible that viruses could cause a disease as complex as cancer. Inspired by Gross's initial experiments, similar results were obtained by Sarah Stewart and Bernice Eddy who later renamed the parotid tumor virus SE polyoma virus after finding it could cause many different types of tumors in mice, hamsters, and rats. Eventually the "SE" was dropped and virologists adopted the name "polyoma virus." After Gross's work was published, additional viruses capable of causing solid tumors or blood-borne tumors in mice were described by Arnold Graffi, Charlotte Friend, John Moloney and others. By 1961, sufficient data had been accumulated for Gross to confidently publish an extensive monograph--Oncogenic Viruses--the first history of tumor virology, which became a standard reference work and marked the emergence of tumor virology as a distinct, legitimate field of study. Copyright © 2014 Elsevier Ltd. All rights reserved.

Pegasus XL CYGNSS Launch Attempt - Prepared for Takeoff - Scrubb

NASA Image and Video Library

2016-12-12

An Orbital ATK L-1011 Stargazer aircraft carrying a Pegasus XL Rocket with eight NASA Cyclone Global Navigation Satellite System, or CYGNSS, spacecraft is ready for takeoff from the Skid Strip at Cape Canaveral Air Force Station, Florida. With the aircraft flying off shore, the Pegasus rocket will be released. Five seconds later, the solid propellant engine will ignite and boost the eight hurricane observatories to orbit. The eight CYGNSS satellites will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes.

48 CFR 52.247-10 - Net Weight-General Freight.

Code of Federal Regulations, 2010 CFR

2010-10-01

... weighmaster on a certified scale) from the gross weight of the vehicle (determined by having the loaded... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Net Weight-General Freight....247-10 Net Weight—General Freight. As prescribed in 47.207-4(a)(2), insert the following clause in...

A comparison of take-off dynamics during three different spikes, block and counter-movement jump in female volleyball players.

PubMed

Kabacinski, Jaroslae; Dworak, Lecholslaw B; Murawa, Michal; Ostarello, John; Rzepnicka, Agata; Maczynski, Jacek

2016-12-01

The purpose of the study was to compare the take-off dynamics in counter-movement jump (CMJ), volleyball block and spikes. Twelve professional female players, representing the highest volleyball league in Poland, participated in the laboratory tests. A force platform was used to record ground reaction force (GRF) during take-off phase in CMJ test, block from a run-up and spikes: front row attack, slide attack, back row attack. Vertical (v) GRF (peak: Rmax and integral mean: ), impulse of vGRF (J) and mechanical power (peak: Pmax and integral mean:

) were analyzed. Significant differences (P<0.05) of values of the dynamic parameters (Rmax, , J, Pmax, and

) were found between CMJ, block from a run-up and three different technique spikes. The highest values were recorded during take-off in the back row attack: peak vGRF (2.93±0.05 BW), integral mean vGRF (1.90±0.08 BW), impulse of vGRF (354±40 Ns), peak power (5320±918 W) and integral mean power (3604±683 W). Peak power (2608±217 W) and integral mean power (1417±94 W) were determined in CMJ test to evaluate the force-velocity capabilities of the players. In terms of GRF and the mechanical power, high level of dynamics in take-off influences positively the jumping height and significantly increases the effectiveness of attacks during spike of the ball over the block of the opponent.

Design of sidewall treatment of cabin noise control of a twin engine turboprop aircraft

NASA Technical Reports Server (NTRS)

Vaicaitis, R.; Slazak, M.

1983-01-01

An analytical procedure was used to predict the noise transmission into the cabin of a twin engine general aviation aircraft. This model was then used to optimize the interior A weighted noise levels to an average value of about 85 dBA. The surface pressure noise spectral levels were selected utilizing experimental flight data and empirical predictions. The add on treatments considered in this optimization study include aluminum honeycomb panels, constrained layer damping tape, porous acoustic blankets, acoustic foams, septum barriers and limp trim panels which are isolated from the vibration of the main sidewall structure. To reduce the average noise level in the cabin from about 102 kBA (baseline) to 85 dBA (optimized), the added weight of the noise control treatment is about 2% of the total gross takeoff weight of the aircraft.

Design of sidewall treatment of cabin noise control of a twin engine turboprop aircraft

NASA Astrophysics Data System (ADS)

Vaicaitis, R.; Slazak, M.

1983-12-01

An analytical procedure was used to predict the noise transmission into the cabin of a twin engine general aviation aircraft. This model was then used to optimize the interior A weighted noise levels to an average value of about 85 dBA. The surface pressure noise spectral levels were selected utilizing experimental flight data and empirical predictions. The add on treatments considered in this optimization study include aluminum honeycomb panels, constrained layer damping tape, porous acoustic blankets, acoustic foams, septum barriers and limp trim panels which are isolated from the vibration of the main sidewall structure. To reduce the average noise level in the cabin from about 102 kBA (baseline) to 85 dBA (optimized), the added weight of the noise control treatment is about 2% of the total gross takeoff weight of the aircraft.

Design of a large span-distributed load flying-wing cargo airplane with laminar flow control

NASA Technical Reports Server (NTRS)

Lovell, W. A.; Price, J. E.; Quartero, C. B.; Turriziani, R. V.; Washburn, G. F.

1978-01-01

A design study was conducted to add laminar flow control to a previously design span-distributed load airplane while maintaining constant range and payload. With laminar flow control applied to 100 percent of the wing and vertical tail chords, the empty weight increased by 4.2 percent, the drag decreased by 27.4 percent, the required engine thrust decreased by 14.8 percent, and the fuel consumption decreased by 21.8 percent. When laminar flow control was applied to a lesser extent of the chord (approximately 80 percent), the empty weight increased by 3.4 percent, the drag decreased by 20.0 percent, the required engine thrust decreased by 13.0 percent, and the fuel consumption decreased by 16.2 percent. In both cases the required take-off gross weight of the aircraft was less than the original turbulent aircraft.

Far-Field Acoustic Power Level and Performance Analyses of F31/A31 Open Rotor Model at Simulated Scaled Takeoff, Nominal Takeoff, and Approach Conditions: Technical Report I

NASA Technical Reports Server (NTRS)

Sree, Dave

2015-01-01

Far-field acoustic power level and performance analyses of open rotor model F31/A31 have been performed to determine its noise characteristics at simulated scaled takeoff, nominal takeoff, and approach flight conditions. The nonproprietary parts of the data obtained from experiments in 9- by 15-Foot Low-Speed Wind Tunnel (9?15 LSWT) tests were provided by NASA Glenn Research Center to perform the analyses. The tone and broadband noise components have been separated from raw test data by using a new data analysis tool. Results in terms of sound pressure levels, acoustic power levels, and their variations with rotor speed, angle of attack, thrust, and input shaft power have been presented and discussed. The effect of an upstream pylon on the noise levels of the model has been addressed. Empirical equations relating model's acoustic power level, thrust, and input shaft power have been developed. The far-field acoustic efficiency of the model is also determined for various simulated flight conditions. It is intended that the results presented in this work will serve as a database for comparison and improvement of other open rotor blade designs and also for validating open rotor noise prediction codes.

20 CFR 209.13 - Employers' gross earnings reports.

Code of Federal Regulations, 2010 CFR

2010-04-01

... RAILROAD EMPLOYERS' REPORTS AND RESPONSIBILITIES § 209.13 Employers' gross earnings reports. (a) Each employer is required to report the gross earnings of a one-percent sample group of railroad employees. The... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Employers' gross earnings reports. 209.13...

76 FR 6050 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

... Medford Rogue Valley Intl- 1/0369 1/5/11 ILS OR LOC/DME RWY 14, Amdt 2 Medford. 10-Mar-11 NM Roswell Roswell Intl Air 1/0543 1/7/11 Takeoff Minimums and Obstacle DP, Orig Center. 10-Mar-11 TX El Paso Horizon...

Effect of increasing truck weight on bridges.

DOT National Transportation Integrated Search

2010-09-01

Legislation has been proposed that will allow a 17,000 lb increase in the maximum gross vehicle : weight on the Interstate Highway System. This projects main goal is quantify the effect of this : increase on the internal forces to which typical sl...

Effects of laminar flow control on the performance of a large span-distributed-load flying-wing cargo airplane concept

NASA Technical Reports Server (NTRS)

Jernell, L. S.

1978-01-01

The effects of laminar flow control (LFC) on the performance of a large span-distributed-load flying-wing cargo airplane concept having a design payload of 2.669 MN and range of 5.93 Mm were determined. Two configurations were considered. One employed laminarized flow over the entire surfaces of the wing and vertical tails, with the exception of the estimated areas of interference due to the fuselage and engines. The other case differed only in that laminar flow was not applied to the flaps, elevons, spoilers, or rudders. The two cases are referred to as the 100 percent and 80 percent laminar configurations, respectively. The utilization of laminar flow control results in reductions in the standard day, sea level installed maximum static thrust per engine from 240 kN for the non-LFC configuration to 205 kN for the 100 percent laminar configuration and 209 kN for the 80 percent case. Weight increases due to the LFC systems cause increases in the operating empty weights of approximately 3 to 4 percent. The design takeoff gross weights decrease approximately 3 to 5 percent. The FAR-25 takeoff field distances for the LFC configurations are greater by about 6 to 7 percent. Fuel efficiencies for the respective configurations are increased 33 percent and 23 percent.

32 CFR 644.43 - Gross appraisals.

Code of Federal Regulations, 2010 CFR

2010-07-01

... HANDBOOK Appraisal § 644.43 Gross appraisals. (a) Preparation. (1) The gross appraisal sections of real...-type or brief real estate design memoranda on civil works projects are submitted, comparable sales data... issued on the same project and if values have changed in the interim, additional sales data submitted to...

32 CFR 644.43 - Gross appraisals.

Code of Federal Regulations, 2011 CFR

2011-07-01

... HANDBOOK Appraisal § 644.43 Gross appraisals. (a) Preparation. (1) The gross appraisal sections of real...-type or brief real estate design memoranda on civil works projects are submitted, comparable sales data... issued on the same project and if values have changed in the interim, additional sales data submitted to...

Analysis of Convair 990 rejected-takeoff accident with emphasis on decision making, training and procedures

NASA Technical Reports Server (NTRS)

Batthauer, Byron E.

1987-01-01

This paper analyzes a NASA Convair 990 (CV-990) accident with emphasis on rejected-takeoff (RTO) decision making, training, procedures, and accident statistics. The NASA Aircraft Accident Investigation Board was somewhat perplexed that an aircraft could be destroyed as a result of blown tires during the takeoff roll. To provide a better understanding of tire failure RTO's, The Board obtained accident reports, Federal Aviation Administration (FAA) studies, and other pertinent information related to the elements of this accident. This material enhanced the analysis process and convinced the Accident Board that high-speed RTO's in transport aircraft should be given more emphasis during pilot training. Pilots should be made aware of various RTO situations and statistics with emphasis on failed-tire RTO's. This background information could enhance the split-second decision-making process that is required prior to initiating an RTO.

7 CFR 1410.44 - Average adjusted gross income.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Average adjusted gross income. 1410.44 Section 1410... Average adjusted gross income. (a) Benefits under this part will not be available to persons or legal entities whose average adjusted gross income exceeds $1,000,000 or as further specified in part 1400...

7 CFR 1410.44 - Average adjusted gross income.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 10 2011-01-01 2011-01-01 false Average adjusted gross income. 1410.44 Section 1410... Average adjusted gross income. (a) Benefits under this part will not be available to persons or legal entities whose average adjusted gross income exceeds $1,000,000 or as further specified in part 1400...

Determination of gross alpha and gross beta in soil around repository facility at Bukit Kledang, Perak, Malaysia

NASA Astrophysics Data System (ADS)

Adziz, Mohd Izwan Abdul; Siong, Khoo Kok

2018-04-01

Recently, the Long Term Storage Facility (LTSF) in Bukit Kledang, Perak, Malaysia, has been upgraded to repository facility upon the completion of decontamination and decommissioning (D&D) process. Thorium waste and contaminated material that may contain some minor amounts of thorium hydroxide were disposed in this facility. This study is conducted to determine the concentrations of gross alpha and gross beta radioactivities in soil samples collected around the repository facility. A total of 12 soil samples were collected consisting 10 samples from around the facility and 2 samples from selected residential area near the facility. In addition, the respective dose rates were measured 5 cm and 1 m above the ground by using survey meter with Geiger Muller (GM) detector and Sodium Iodide (NaI) detector. Soil samples were collected using hand auger and then were taken back to the laboratory for further analysis. Samples were cleaned, dried, pulverized and sieved prior to analysis. Gross alpha and gross beta activity measurements were carried out using gas flow proportional counter, Canberra Series 5 XLB - Automatic Low Background Alpha and Beta Counting System. The obtained results show that, the gross alpha and gross beta activity concentration ranged from 1.55 to 5.34 Bq/g with a mean value of 3.47 ± 0.09 Bq/g and 1.64 to 5.78 Bq/g with a mean value of 3.49 ± 0.09 Bq/g, respectively. These results can be used as an additional data to represent terrestrial radioactivity baseline data for Malaysia environment. This estimation will also serve as baseline for detection of any future related activities of contamination especially around the repository facility area.

Update of Aircraft Profile Data for the Integrated Noise Model Computer Program. Volume 2. Appendix A: Aircraft Takeoff and Landing Profiles

DTIC Science & Technology

1992-03-01

8 KT) 02- 10 -1992 09: 48 :32 AIRCRAFT ID AIRCRAFT AND ENGINE AIRCRAFT NUMBER NAMES CATEGORY ------------------- ------------------- -------- 003...MAX CLIMB 8 CLIMB ZErO MAX CLIMB 9 CLIMB ZERO MAX CLIMB A-21 TAKEOFF PROFILE DATA (HEADWIND = 8 KT) 02- 10 -1992 09: 48 :36 AIRCRAFT AIRCRAFT AND ENGINE...CLIMB ZERO USR SUPPL 34033 LB 10 CLIMB ZERO USR SUPPL 34798 LB A-194 TAKEOFF PROFILE DATA (HEADWIND = 8 KT) 06-24-1991 10 :33: 48 AIRCRAFT AIRCRAFT

75 FR 35627 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-23

... Diego Montgomery Field.... 0/4634 6/9/10 TAKEOFF MINIMUMS AND OBSTACLE DP, AMDT 3. 29-Jul-10 CQ Saipan Francisco C. Ada/ 0/9757 3/16/10 ILS OR LOC/DME RWY 7, AMDT 5A. Saipan Intl. [FR Doc. 2010-14980 Filed 6-22...

Trim drag reduction concepts for horizontal takeoff single-stage-to-Orbit vehicles

NASA Technical Reports Server (NTRS)

Shaughnessy, John D.; Gregory, Irene M.

1991-01-01

The results of a study to investigate concepts for minimizing trim drag of horizontal takeoff single-stage-to-orbit (SSTO) vehicles are presented. A generic hypersonic airbreathing conical configuration was used as the subject aircraft. The investigation indicates that extreme forward migration of the aerodynamic center as the vehicle accelerates to orbital velocities causes severe aerodynamic instability and trim moments that must be counteracted. Adequate stability can be provided by active control of elevons and rudder, but use of elevons to produce trim moments results in excessive trim drag and fuel consumption. To alleviate this problem, two solution concepts are examined. Active control of the center of gravity (COG) location to track the aerodynamic center decreases trim moment requirements, reduces elevon deflections, and leads to significant fuel savings. Active control of the direction of the thrust vector produces required trim moments, reduces elevon deflections, and also results in significant fuel savings. It is concluded that the combination of active flight control to provide stabilization, (COG) position control to minimize trim moment requirements, and thrust vectoring to generate required trim moments has the potential to significantly reduce fuel consumption during ascent to orbit of horizontal takeoff SSTO vehicles.

Pegasus XL CYGNSS Launch Attempt - Prepared for Takeoff - Scrubb

NASA Image and Video Library

2016-12-12

A pathfinder aircraft prepares for takeoff from the Skid Strip at Cape Canaveral Air Force Station in Florida. The airplane will provide photographic and video imagery of the Orbital ATK L-1011 Stargazer aircraft carrying a Pegasus XL Rocket with eight NASA Cyclone Global Navigation Satellite System, or CYGNSS, spacecraft. With the aircraft flying off shore, the Pegasus rocket will be released. Five seconds later, the solid propellant engine will ignite and boost the eight hurricane observatories to orbit. The eight CYGNSS satellites will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes.

Concept identification for a power take-off shielding campaign.

PubMed

Tinc, P J; Madden, E; Park, S; Weil, R; Sorensen, J A

2015-01-01

ABSTRACT Machinery entanglements, specifically power take-off (PTO) entanglements, are a leading cause of injuries and fatalities on farms. In order to address this life-threatening issue, a social marketing campaign is being developed to reduce barriers and emphasize motivators to shielding. This article discusses the process of designing, testing, and selecting concepts to be used in the campaign. Small-group discussions (triads) were held to test 13 message concepts. Participants were asked to provide feedback and select the two messages that they believed to be most powerful. Upon completion, three message concepts were selected to be finalized.

Reusable aerospace system with horizontal take-off

NASA Astrophysics Data System (ADS)

Lozino-Lozinskii, G. E.; Shkadov, L. M.; Plokhikh, V. P.

1990-10-01

An aerospace system (ASS) concept aiming at cost reductions for launching facilities, reduction of ground preparations for start and launch phases, flexibility of use, international inspection of space systems, and emergency rescue operations is presented. The concept suggests the utilization of an AN-225 subsonic carrier aircraft capable of carrying up to 250 ton of the external load, external fuel tank, and orbital spacecraft. It includes a horizontal take-off, full reusable or single-use system, orbital aircraft with hypersonic characteristics, the use of an air-breathing jet engine on the first stage of launch, and the utilization of advanced structural materials. Among possible applications for ASS are satellite launches into low supporting orbits, suborbital cargo and passenger flights, scientific and economic missions, and the technical servicing of orbital vehicles and stations.

14 CFR 25.533 - Hull and main float bottom pressures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main... figure 2 of appendix B; V S 1=seaplane stalling speed (Knots) at the design water takeoff weight with... design water takeoff weight with flaps extended in the appropriate takeoff position; and β=angle of dead...

14 CFR 23.533 - Hull and main float bottom pressures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float...=seaplane stalling speed (knots) at the design water takeoff weight with flaps extended in the appropriate...) at the design water takeoff weight with flaps extended in the appropriate takeoff position; and β...

14 CFR 25.533 - Hull and main float bottom pressures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main... figure 2 of appendix B; V S 1=seaplane stalling speed (Knots) at the design water takeoff weight with... design water takeoff weight with flaps extended in the appropriate takeoff position; and β=angle of dead...

14 CFR 23.533 - Hull and main float bottom pressures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float...=seaplane stalling speed (knots) at the design water takeoff weight with flaps extended in the appropriate...) at the design water takeoff weight with flaps extended in the appropriate takeoff position; and β...

77 FR 51896 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-28

... provisions. The incorporation by reference of certain publications listed in the regulations is approved by... incorporated by reference in the amendment is as follows: For Examination-- 1. FAA Rules Docket, FAA..., individual SIAP and Takeoff Minimums and ODP copies may be obtained from: 1. FAA Public Inquiry Center (APA...

77 FR 50012 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-20

..., Amdt 2 Oklahoma City, OK, Will Rogers World, Takeoff Minimums and Obstacle DP, Amdt 1 Portland, OR... CLOSE PARALLEL), Amdt 4, CANCELED Philadelphia, PA, Philadelphia Intl, ILS PRM RWY 27L (SIMULTANEOUS CLOSE PARALLEL), Amdt 3, CANCELED Pittsburgh, PA, Allegheny County, ILS OR LOC RWY 10, Amdt 6 Pittsburgh...

75 FR 32094 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

... OBSTACLE DP, ORIG 1-Jul-10 TX DALLAS ADDISON 0/6690 4/21/10 TAKEOFF MINIMUMS AND OBSTACLE DP, AMDT 5 1-Jul.../10 ILS OR LOC RWY 10R, AMDT 3 1-Jul-10 PA LOCK HAVEN WILLIAM T. PIPER 0/9245 5/12/10 RNAV (GPS)-1...

Concept for a large multi-mission amphibian aircraft

NASA Technical Reports Server (NTRS)

Vaughan, J. C., III; Earl, T. D.

1979-01-01

A very large aircraft has been proposed for meeting both civil cargo and military transport needs for 1995 and beyond. The concept includes a wide noncircular fuselage cross section with a low wing, thick inner wing section, fuselage-mounted engines, and an air cushion landing gear. The civil freighter operates independently of congested passenger airports, using sheltered water as a runway and a waterfront land site for parking and ground operations. The military transport can operate from a wide variety of surfaces and temporary bases. The air cushion landing gear weighs substantially less than conventional gear and permits the use of extended takeoff distance resulting in improved payload/gross weight ratio.

Gross Olfaction Before and After Laparoscopic Gastric Bypass.

PubMed

Zerrweck, Carlos; Gallardo, Vannia Castañeda; Calleja, Carmen; Sepúlveda, Elisa; Guilber, Lizbeth

2017-11-01

Obesity leads to olfaction alterations, and this can further impact food choices, appetite, and nutritional status. Bariatric procedures induce weight loss and change in taste and smell perception, but more information is needed, especially using objective olfaction tests. A prospective study was conducted during 6 months, with candidates to laparoscopic gastric bypass at a single institution. A preoperative nasofibroscopy and gross smell identification test (The Pocket Smell Test ®) were performed in those meeting the inclusion criteria. After 6 months, a new test was performed, and the primary objective was to determine if there was an improvement in the olfaction score. Weight loss and comorbidities improvement were also analyzed. From the 30 patients with morbid obesity enrolled, 21 met the inclusion criteria and ENT evaluation. At baseline, 42.8% of patients scored 3 points, 53.3% scored 2 points, and 4.7% scored 1 point. After 6 months, there was a -81.1% of change. Seventeen patients scored 3 points (p = 0.002 vs initial) and two scored 2 points (p = 0.006 vs initial). There were no patients with less than 2 points. Weight and comorbidities had a significant improvement as well. Laparoscopic gastric bypass improves the olfaction scores of the Pocket Smell Test in morbidly obese patients 6 months after their procedure. More complex tests can be used in candidates to bariatric surgery if low scores are detected initially. Other causes of olfaction dysfunctions should be determined if there is no improvement after weight loss.

Validating the Rett Syndrome Gross Motor Scale.

PubMed

Downs, Jenny; Stahlhut, Michelle; Wong, Kingsley; Syhler, Birgit; Bisgaard, Anne-Marie; Jacoby, Peter; Leonard, Helen

2016-01-01

Rett syndrome is a pervasive neurodevelopmental disorder associated with a pathogenic mutation on the MECP2 gene. Impaired movement is a fundamental component and the Rett Syndrome Gross Motor Scale was developed to measure gross motor abilities in this population. The current study investigated the validity and reliability of the Rett Syndrome Gross Motor Scale. Video data showing gross motor abilities supplemented with parent report data was collected for 255 girls and women registered with the Australian Rett Syndrome Database, and the factor structure and relationships between motor scores, age and genotype were investigated. Clinical assessment scores for 38 girls and women with Rett syndrome who attended the Danish Center for Rett Syndrome were used to assess consistency of measurement. Principal components analysis enabled the calculation of three factor scores: Sitting, Standing and Walking, and Challenge. Motor scores were poorer with increasing age and those with the p.Arg133Cys, p.Arg294* or p.Arg306Cys mutation achieved higher scores than those with a large deletion. The repeatability of clinical assessment was excellent (intraclass correlation coefficient for total score 0.99, 95% CI 0.93-0.98). The standard error of measurement for the total score was 2 points and we would be 95% confident that a change 4 points in the 45-point scale would be greater than within-subject measurement error. The Rett Syndrome Gross Motor Scale could be an appropriate measure of gross motor skills in clinical practice and clinical trials.

78 FR 43782 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-22

..., CANCELED Kalamazoo, MI, Kalamazoo/Battle Creek Intl, RNAV (GPS) RWY 17, Amdt 1 Traverse City, MI, Cherry Capitol, GPS RWY 36, Orig-B, CANCELED Traverse City, MI, Cherry Capitol, RNAV (GPS) RWY 36, Orig Dodge..., Cassville Muni, Takeoff Minimums and Obstacle DP, Amdt 1 Fredericktown, MO, A. Paul Vance Fredericktown Rgnl...

76 FR 55233 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-07

... as the anticipated impact is so minimal. For the same reason, the FAA certifies that this amendment will not have a significant economic impact on a substantial number of small entities under the... Rgnl, Takeoff Minimums and Obstacle DP, Orig Beaver Falls, PA, Beaver County, LOC RWY 10, Amdt 4...

14 CFR 121.637 - Takeoffs from unlisted and alternate airports: Domestic and flag operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.637 Section 121.637 Aeronautics and Space FEDERAL AVIATION... weather conditions at that airport are equal to or better than the following: (i) Airports in the United...

14 CFR 121.637 - Takeoffs from unlisted and alternate airports: Domestic and flag operations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.637 Section 121.637 Aeronautics and Space FEDERAL AVIATION... weather conditions at that airport are equal to or better than the following: (i) Airports in the United...

14 CFR 121.637 - Takeoffs from unlisted and alternate airports: Domestic and flag operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.637 Section 121.637 Aeronautics and Space FEDERAL AVIATION... weather conditions at that airport are equal to or better than the following: (i) Airports in the United...

14 CFR 121.637 - Takeoffs from unlisted and alternate airports: Domestic and flag operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.637 Section 121.637 Aeronautics and Space FEDERAL AVIATION... weather conditions at that airport are equal to or better than the following: (i) Airports in the United...

14 CFR 121.637 - Takeoffs from unlisted and alternate airports: Domestic and flag operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.637 Section 121.637 Aeronautics and Space FEDERAL AVIATION... weather conditions at that airport are equal to or better than the following: (i) Airports in the United...

A Brief Hydrodynamic Investigation of a 1/24-Scale Model of the DR-77 Seaplane

NASA Technical Reports Server (NTRS)

Fisher, Lloyd J.; Hoffman, Edward L.

1953-01-01

A limited investigation of a 1/24-scale dynamically similar model of the Navy Bureau of Aeronautics DR-77 design was conducted in Langley tank no. 2 to determine the calm-water take-off and the rough-water landing characteristics of the design with particular regard to the take-off resistance and the landing accelerations. During the take-off tests, resistance, trim, and rise were measured and photographs were taken to study spray. During the landing tests, motion-picture records and normal-acceleration records were obtained. A ratio of gross load to maximum resistance of 3.2 was obtained with a 30 deg. dead-rise hydro-ski installation. The maximum normal accelerations obtained with a 30 deg. dead-rise hydro-ski installation were of the order of 8g to log in waves 8 feet high (full scale). A yawing instability that occurred just prior to hydro-ski emergence was improved by adding an afterbody extension, but adding the extension reduced the ratio of gross load to maximum resistance to 2.9.

An avulsed radial artery with a high take-off.

PubMed

Rojas-Marte, Geurys; Chen, On; Verma, Shivani; Rao, Atul; Shani, Jacob; Ayzenberg, Sergey

2015-04-01

A 63-year-old female was diagnosed with severe aortic stenosis, who underwent a diagnostic coronary angiography via transradial approach prior an aortic-valve replacement. After imaging the left coronary system, entrapment of the diagnostic catheter was encountered as a result of spasm of the radial artery. An arteriogram of the arm revealed an anatomical variation in the radial artery (high take-off). Several attempts to remove the entrapped catheter resulted in avulsion of the artery, which was managed successfully with coil embolization. To our knowledge, no such complication has been reported. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Gross motor skill development of kindergarten children in Japan.

PubMed

Aye, Thanda; Kuramoto-Ahuja, Tsugumi; Sato, Tamae; Sadakiyo, Kaori; Watanabe, Miyoko; Maruyama, Hitoshi

2018-05-01

[Purpose] The purposes of this study were to assess and explore the gender-based differences in gross motor skill development of 5-year-old Japanese children. [Subjects and Methods] This cross-sectional study recruited 60 healthy 5-year-old (third-year kindergarten, i.e., nencho ) children (34 boys, 26 girls) from one local private kindergarten school in Otawara city, Tochigi Prefecture, Japan. Gross motor skills, including six locomotor and six object control skills, were assessed using the test of gross motor development, second edition (TGMD-2). All subjects performed two trials of each gross motor skill, and the performances were video-recorded and scored. Assessment procedures were performed according to the standardized guidelines of the TGMD-2. [Results] The majority of subjects had an average level of overall gross motor skills. Girls had significantly better locomotor skills. Boys had significantly better object control skills. [Conclusion] The gross motor skill development of 5-year-old Japanese children involves gender-based differences in locomotor and object control skills. This study provided valuable information that can be used to establish normative references for the gross motor skills of 5-year-old Japanese children.

Gross motor skill development of kindergarten children in Japan

PubMed Central

Aye, Thanda; Kuramoto-Ahuja, Tsugumi; Sato, Tamae; Sadakiyo, Kaori; Watanabe, Miyoko; Maruyama, Hitoshi

2018-01-01

[Purpose] The purposes of this study were to assess and explore the gender-based differences in gross motor skill development of 5-year-old Japanese children. [Subjects and Methods] This cross-sectional study recruited 60 healthy 5-year-old (third-year kindergarten, i.e., nencho) children (34 boys, 26 girls) from one local private kindergarten school in Otawara city, Tochigi Prefecture, Japan. Gross motor skills, including six locomotor and six object control skills, were assessed using the test of gross motor development, second edition (TGMD-2). All subjects performed two trials of each gross motor skill, and the performances were video-recorded and scored. Assessment procedures were performed according to the standardized guidelines of the TGMD-2. [Results] The majority of subjects had an average level of overall gross motor skills. Girls had significantly better locomotor skills. Boys had significantly better object control skills. [Conclusion] The gross motor skill development of 5-year-old Japanese children involves gender-based differences in locomotor and object control skills. This study provided valuable information that can be used to establish normative references for the gross motor skills of 5-year-old Japanese children. PMID:29765187

75 FR 45047 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-02

...;Prices of new books are listed in the first FEDERAL REGISTER issue of each #0;week. #0; #0; #0; #0;#0..., individual SIAP and Takeoff Minimums and ODP copies may be obtained from: 1. FAA Public Inquiry Center (APA... for a special format make publication in the Federal Register expensive and impractical. Furthermore...

78 FR 40383 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-05

..., WI, Baraboo Wisconsin Dells, LOC/DME RWY 1, Amdt 1 Baraboo, WI, Baraboo Wisconsin Dells, RNAV (GPS) RWY 1, Amdt 1 Baraboo, WI, Baraboo Wisconsin Dells, RNAV (GPS) RWY 19, Amdt 1 Baraboo, WI, Baraboo Wisconsin Dells, Takeoff Minimums and Obstacle DP, Amdt 1 Charleston, WV, Yeager, RNAV (RNP) Z RWY 5, Orig...

77 FR 26669 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-07

...., Oklahoma City, OK 73169 or, 4. The National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741- 6030, or go to: http://www.archives.gov..., Amdt 1 Leesburg, VA, Leesburg Executive, RNAV (GPS) RWY 17, Amdt 3 New Market, VA, New Market, Takeoff...

77 FR 45922 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-02

..., Atkinson Muni, RNAV (GPS) RWY 34, Amdt 2 Gonzales, LA, Louisiana Rgnl, RNAV (GPS) RWY 17, Amdt 1 Gonzales, LA, Louisiana Rgnl, RNAV (GPS) RWY 35, Amdt 1 Gonzales, LA, Louisiana Rgnl, Takeoff Minimums and Obstacle DP, Amdt 1 Slidell, LA, Slidell, NDB RWY 36, Orig-E, CANCELED Vineyard Haven, MA, Marthas Vineyard...

75 FR 78897 - Definition of Omission From Gross Income

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-17

... Definition of Omission From Gross Income AGENCY: Internal Revenue Service (IRS), Treasury. ACTION: Final regulations. SUMMARY: This document contains final regulations defining an omission from gross income for... overstatement of basis in a sold asset results in an omission from gross income. The regulations will affect any...

29 CFR 779.259 - What is included in annual gross volume.

Code of Federal Regulations, 2013 CFR

2013-07-01

... whole. The computation of the annual gross volume of sales or business of the enterprise is made... Coverage Annual Gross Volume of Sales Made Or Business Done § 779.259 What is included in annual gross volume. (a) The annual gross volume of sales made or business done of an enterprise consists of its gross...

29 CFR 779.259 - What is included in annual gross volume.

Code of Federal Regulations, 2012 CFR

2012-07-01

... whole. The computation of the annual gross volume of sales or business of the enterprise is made... Coverage Annual Gross Volume of Sales Made Or Business Done § 779.259 What is included in annual gross volume. (a) The annual gross volume of sales made or business done of an enterprise consists of its gross...

Evaluation of Four Advanced Nozzle Concepts for Short Takeoff and Landing Performance

NASA Technical Reports Server (NTRS)

Quinto, P. Frank; Kemmerly, Guy T.; Paulson, John W., Jr.

1993-01-01

Four advanced nozzle concepts were tested on a canard-wing fighter in the Langley 14- by 22-Foot Subsonic Tunnel. The four vectoring-nozzle concepts were as follows: (1) an axisymmetric nozzle (AXI); (2) an asymmetric, load balanced exhaust nozzle (ALBEN); (3) a low aspect ratio, single expansion ramp nozzle (LASERN); and (4) a high aspect ratio, single expansion ramp nozzle (HASERN). The investigation was conducted to determine the most suitable nozzle concept for short takeoff and landing (STOL) performance. The criterion for the best STOL performance was a takeoff ground roll of less than 1000 ft. At approach, the criteria were high lift and sufficient drag to maintain a glide slope of -3 to -6 deg with enough pitching-moment control from the canards. The test was performed at a dynamic pressure of 45 lb/sq ft and an angle-of-attack range of 0 to 20 deg. The nozzle pressure ratio was varied from 1.0 to 4.3 at both dry power and after burning nozzle configurations with nozzle vectoring to 60 deg. In addition, the model was tested in and out of ground effects. The ALBEN concept was the best of the four nozzle concepts tested for STOL performance.

Low Noise Cruise Efficient Short Take-Off and Landing Transport Vehicle Study

NASA Technical Reports Server (NTRS)

Kim, Hyun D.; Berton, Jeffrey J.; Jones, Scott M.

2007-01-01

The saturation of the airspace around current airports combined with increasingly stringent community noise limits represents a serious impediment to growth in world aviation travel. Breakthrough concepts that both increase throughput and reduce noise impacts are required to enable growth in aviation markets. Concepts with a 25 year horizon must facilitate a 4x increase in air travel while simultaneously meeting community noise constraints. Attacking these horizon issues holistically is the concept study of a Cruise Efficient Short Take-Off and Landing (CESTOL) high subsonic transport under the NASA's Revolutionary Systems Concepts for Aeronautics (RSCA) project. The concept is a high-lift capable airframe with a partially embedded distributed propulsion system that takes a synergistic approach in propulsion-airframe-integration (PAI) by fully integrating the airframe and propulsion systems to achieve the benefits of both low-noise short take-off and landing (STOL) operations and efficient high speed cruise. This paper presents a summary of the recent study of a distributed propulsion/airframe configuration that provides low-noise STOL operation to enable 24-hour use of the untapped regional and city center airports to increase the capacity of the overall airspace while still maintaining efficient high subsonic cruise flight capability.

A mathematical model for Vertical Attitude Takeoff and Landing (VATOL) aircraft simulation. Volume 3: User's manual for VATOL simulation program

NASA Technical Reports Server (NTRS)

Fortenbaugh, R. L.

1980-01-01

Instructions for using Vertical Attitude Takeoff and Landing Aircraft Simulation (VATLAS), the digital simulation program for application to vertical attitude takeoff and landing (VATOL) aircraft developed for installation on the NASA Ames CDC 7600 computer system are described. The framework for VATLAS is the Off-Line Simulation (OLSIM) routine. The OLSIM routine provides a flexible framework and standardized modules which facilitate the development of off-line aircraft simulations. OLSIM runs under the control of VTOLTH, the main program, which calls the proper modules for executing user specified options. These options include trim, stability derivative calculation, time history generation, and various input-output options.

7 CFR 701.17 - Average adjusted gross income limitation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Average adjusted gross income limitation. 701.17... RELATED PROGRAMS PREVIOUSLY ADMINISTERED UNDER THIS PART § 701.17 Average adjusted gross income limitation... 9003), each applicant must meet the provisions of the Adjusted Gross Income Limitations at 7 CFR part...

Performance deterioration due to acceptance testing and flight loads; JT90 jet engine diagnostic program

NASA Technical Reports Server (NTRS)

Olsson, W. J.

1982-01-01

The results of a flight loads test of the JT9D-7 engine are presented. The goals of this test program were to: measure aerodynamic and inertia loads on the engine during flight, explore the effects of airplane gross weight and typical maneuvers on these flight loads, simultaneously measure the changes in engine running clearances and performance resulting from the maneuvers, make refinements of engine performance deterioration prediction models based on analytical results of the tests, and make recommendations to improve propulsion system performance retention. The test program included a typical production airplane acceptance test plus additional flights and maneuvers to encompass the range of flight loads in revenue service. The test results indicated that aerodynamic loads, primarily at take-off, were the major cause of rub-indicated that aerodynamic loads, primarily at take-off, were the major cause of rub-induced deterioration in the cold sectin of the engine. Differential thermal expansion between rotating and static parts plus aerodynamic loads combined to cause blade-to-seal rubs in the turbine.

DC-9 Flight Demonstration Program with Refanned JT8D Engines. Volume 3; Performance and Analysis

NASA Technical Reports Server (NTRS)

1975-01-01

The JT8D-109 engine has a sea level static, standard day bare engine takeoff thrust of 73,840 N. At sea level standard day conditions the additional thrust of the JT8D-109 results in 2,040 kg additional takeoff gross weight capability for a given field length. Range loss of the DC-9 Refan airplane for long range cruise was determined. The Refan airplane demonstrated stall, static longitudinal stability, longitudinal control, longitudinal trim, minimum control speeds, and directional control characteristics similar to the DC-9-30 production airplane and complied with airworthiness requirements. Cruise, climb, and thrust reverser performance were evaluated. Structural and dynamic ground test, flight test and analytical results substantiate Refan Program requirements that the nacelle, thrust reverser hardware, and the airplane structural modifications are flightworthy and certifiable and that the airplane meets flutter speed margins. Estimated unit cost of a DC-9 Refan retrofit program is 1.338 million in mid-1975 dollars with about an equal split in cost between airframe and engine.

75 FR 32096 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

.... The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and the need... Rivers, MI, Three Rivers Muni Dr. Haines, NDB RWY 27, Amdt 7A, CANCELLED Brainerd, MN, Brainerd Lakes Rgnl, RNAV (GPS) RWY 5, Amdt 1 Brainerd, MN, Brainerd Lakes Rgnl, RNAV (GPS) RWY 12, Amdt 1 Brainerd...

77 FR 71497 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-03

.... The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and the need.../Springfield, MA, Barnes Muni, RNAV (GPS) RWY 20, Amdt 1 Moose Lake, MN, Moose Lake Carlton County, GPS RWY 4, Orig, CANCELED Moose Lake, MN, Moose Lake Carlton County, RNAV (GPS) RWY 4, Orig Indianola, MS...

76 FR 8291 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-14

... 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and... DP, Amdt 3A Ely, MN, Ely Muni, VOR-A, Orig, CANCELLED Paynesville, MN, Paynesville Muni, RNAV (GPS) RWY 11, Orig Paynesville, MN, Paynesville Muni, RNAV (GPS) RWY 29, Orig Kansas City, MO, Kansas City...

78 FR 10058 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-13

...: Effective 7 MARCH 2013 Tatitlek, AK, Tatitlek, RNAV (GPS) RWY 31, Orig-A Jonesboro, AR, Jonesboro Muni, RNAV (GPS) RWY 5, Amdt 1 Jonesboro, AR, Jonesboro Muni, RNAV (GPS) RWY 23, Amdt 1 Jonesboro, AR, Jonesboro Muni, RNAV (GPS) RWY 31, Amdt 1 Jonesboro, AR, Jonesboro Muni, Takeoff Minimums and Obstacle DP, Amdt 3...

76 FR 35101 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

... Mobridge, SD, Mobridge Muni, Takeoff Minimums and Obstacle DP, Amdt 1 Spearfish, SD, Black Hills-Clyde Ice Field, GPS RWY 12, Orig-D, CANCELLED Spearfish, SD, Black Hills-Clyde Ice Field, NDB-A, Amdt 1 Spearfish, SD, Black Hills-Clyde Ice Field, RNAV (GPS) RWY 13, Orig Spearfish, SD, Black Hills-Clyde Ice Field...

78 FR 56830 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-16

... Muncie, IN, Delaware County Rgnl, Takeoff Minimums and Obstacle DP, Amdt 4 Bowling Green, KY, Bowling Green-Warren County Rgnl, ILS OR LOC RWY 3, Amdt 1 Bowling Green, KY, Bowling Green-Warren County Rgnl, NDB RWY 3, Amdt 2 Bowling Green, KY, Bowling Green-Warren County Rgnl, RNAV (GPS) RWY 3, Amdt 1...

7 CFR 701.117 - Average adjusted gross income limitation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 7 2011-01-01 2011-01-01 false Average adjusted gross income limitation. 701.117... Conservation Program § 701.117 Average adjusted gross income limitation. To be eligible for payments issued... the provisions of the Adjusted Gross Income Limitations at 7 CFR part 1400 subpart G. [72 FR 45880...

Gross motor development is delayed following early cardiac surgery.

PubMed

Long, Suzanne H; Harris, Susan R; Eldridge, Beverley J; Galea, Mary P

2012-10-01

To describe the gross motor development of infants who had undergone cardiac surgery in the neonatal or early infant period. Gross motor performance was assessed when infants were 4, 8, 12, and 16 months of age with the Alberta Infant Motor Scale. This scale is a discriminative gross motor outcome measure that may be used to assess infants from birth to independent walking. Infants were videotaped during the assessment and were later evaluated by a senior paediatric physiotherapist who was blinded to each infant's medical history, including previous clinical assessments. Demographic, diagnostic, surgical, critical care, and medical variables were considered with respect to gross motor outcomes. A total of 50 infants who underwent elective or emergency cardiac surgery at less than or up to 8 weeks of age, between July 2006 and January 2008, were recruited to this study and were assessed at 4 months of age. Approximately, 92%, 84%, and 94% of study participants returned for assessment at 8, 12, and 16 months of age, respectively. Study participants had delayed gross motor development across all study time points; 62% of study participants did not have typical gross motor development during the first year of life. Hospital length of stay was associated with gross motor outcome across infancy. Active gross motor surveillance of all infants undergoing early cardiac surgery is recommended. Further studies of larger congenital heart disease samples are required, as are longitudinal studies that determine the significance of these findings at school age and beyond.

7 CFR 1424.7 - Gross payable units.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Biodiesel producers will be eligible for payments on gross payable units for all biodiesel production from... rates. Unless otherwise determined by CCC, gross payable units for biodiesel production from eligible inputs will be calculated as follows: (1) For APP, by dividing the gallons of increased biodiesel by the...

7 CFR 1424.7 - Gross payable units.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Biodiesel producers will be eligible for payments on gross payable units for all biodiesel production from... rates. Unless otherwise determined by CCC, gross payable units for biodiesel production from eligible inputs will be calculated as follows: (1) For APP, by dividing the gallons of increased biodiesel by the...

7 CFR 1424.7 - Gross payable units.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Biodiesel producers will be eligible for payments on gross payable units for all biodiesel production from... rates. Unless otherwise determined by CCC, gross payable units for biodiesel production from eligible inputs will be calculated as follows: (1) For APP, by dividing the gallons of increased biodiesel by the...

7 CFR 1424.7 - Gross payable units.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Biodiesel producers will be eligible for payments on gross payable units for all biodiesel production from... rates. Unless otherwise determined by CCC, gross payable units for biodiesel production from eligible inputs will be calculated as follows: (1) For APP, by dividing the gallons of increased biodiesel by the...

7 CFR 1424.7 - Gross payable units.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) Biodiesel producers will be eligible for payments on gross payable units for all biodiesel production from... rates. Unless otherwise determined by CCC, gross payable units for biodiesel production from eligible inputs will be calculated as follows: (1) For APP, by dividing the gallons of increased biodiesel by the...

Behind Start of Take-Off Roll Aircraft Sound Level Directivity Study - Revision 1

NASA Technical Reports Server (NTRS)

Lau, Michael C.; Roof, Christopher J.; Fleming, Gregg G.; Rapoza, Amanda S.; Boeker, Eric R.; McCurdy, David A.; Shepherd, Kevin P.

2015-01-01

The National Aeronautics and Space Administration (NASA), Langley Research Center (LaRC) and the Environmental Measurement and Modeling Division of the Department of Transportation's Volpe National Transportation Systems Center (Volpe) conducted a noise measurement study to examine aircraft sound level directivity patterns behind the start-of-takeoff roll. The study was conducted at Washington Dulles International Airport (IAD) from October 4 through 20, 2004.

26 CFR 1.832-4 - Gross income.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TAXES Other Insurance Companies § 1.832-4 Gross income. (a)(1) Gross income as defined in section 832(b... the exhibit, however, do not reflect an insurance company's income as defined in the Code. By reason... amounts payable to customers under the applicable portion of such arrangements as losses incurred...

75 FR 32655 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

............ WILLOWS-GLENN 0/9850 5/18/10 TAKEOFF MINIMUMS AND OBSTACLE DP, AMDT 1 COUNTY. 29-Jul-10........ NY DUNKIRK......... CHAUTAUQUA 0/1647 5/25/10 VOR RWY 6, AMDT 2 COUNTY/DUNKIRK. 29-Jul-10........ NY DUNKIRK......... CHAUTAUQUA 0/1648 5/25/10 VOR RWY 24, AMDT 7 COUNTY/DUNKIRK. 29-Jul-10........ MS INDIANOLA....... INDIANOLA...

76 FR 64005 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-17

.... The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex nature and the need.... Part 97 is amended to read as follows: Effective 20 OCT 2011 Albert Lea, MN, Albert Lea Muni, RNAV (GPS) RWY 17, Amdt 2 Albert Lea, MN, Albert Lea Muni, RNAV (GPS) RWY 35, Amdt 1 Albert Lea, MN, Albert Lea...

75 FR 35629 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-23

... West Union, IA, George L Scott Muni, GPS RWY 17, Orig, CANCELLED West Union, IA, George L Scott Muni, GPS RWY 35, Orig, CANCELLED West Union, IA, George L Scott Muni, RNAV (GPS) RWY 17, Orig West Union, IA, George L Scott Muni, RNAV (GPS) RWY 35, Orig West Union, IA, George L Scott Muni, Takeoff...

Associations of vitamin D status, bone health and anthropometry, with gross motor development and performance of school-aged Indian children who were born at term with low birth weight.

PubMed

Filteau, Suzanne; Rehman, Andrea M; Yousafzai, Aisha; Chugh, Reema; Kaur, Manpreet; Sachdev, H P S; Trilok-Kumar, Geeta

2016-01-08

There is little information regarding motor development of children born at term with low birth weight (LBW), a group that constitutes a large proportion of children in South Asia. We used data from infancy and at school age from a LBW cohort to investigate children's motor performance using causal inference. Cross-sectional follow-up study. Delhi, India. We recruited 912 children aged 5 years who had participated in a trial of vitamin D for term LBW infants in the first 6 months of life. We focused on gross motor development, using the Ages and Stages Questionnaire (ASQ) gross motor scale and several measures of motor performance. We examined the effects on these of current anthropometry, vitamin D status and bone health, controlling for age, sex, season of interview, socioeconomic variables, early growth, recent morbidity, sun exposure and animal food intake. In adjusted analyses, stunted children (height-for-age Z (HAZ) <-2) took longer to run 20 m (0.52 s, 95% CI 0.35 to 0.70; p<0.001) and had greater odds of a failing score on the ASQ (OR 3.00, 95% CI 1.41 to 6.38, p=0.004). Greater arm muscle area was associated with faster run time, and the ability to perform more stands and squats in 15 s. Poorer vitamin D status was associated with the ability to perform more stands and squats. Lower tibia ultrasound Z score was associated with greater hand grip strength. Early growth and current body mass index had no associations with motor outcomes. Current HAZ and arm muscle area showed the strongest associations with gross motor outcomes, likely due to a combination of simple physics and factors associated with stunting. The counterintuitive inverse associations of tibia health and vitamin D status with outcomes may require further research. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Associations of vitamin D status, bone health and anthropometry, with gross motor development and performance of school-aged Indian children who were born at term with low birth weight

PubMed Central

Filteau, Suzanne; Rehman, Andrea M; Yousafzai, Aisha; Chugh, Reema; Kaur, Manpreet; Sachdev, H P S; Trilok-Kumar, Geeta

2016-01-01

Objectives There is little information regarding motor development of children born at term with low birth weight (LBW), a group that constitutes a large proportion of children in South Asia. We used data from infancy and at school age from a LBW cohort to investigate children's motor performance using causal inference. Design Cross-sectional follow-up study. Setting Delhi, India. Participants We recruited 912 children aged 5 years who had participated in a trial of vitamin D for term LBW infants in the first 6 months of life. Outcome measures We focused on gross motor development, using the Ages and Stages Questionnaire (ASQ) gross motor scale and several measures of motor performance. We examined the effects on these of current anthropometry, vitamin D status and bone health, controlling for age, sex, season of interview, socioeconomic variables, early growth, recent morbidity, sun exposure and animal food intake. Results In adjusted analyses, stunted children (height-for-age Z (HAZ) <−2) took longer to run 20 m (0.52 s, 95% CI 0.35 to 0.70; p<0.001) and had greater odds of a failing score on the ASQ (OR 3.00, 95% CI 1.41 to 6.38, p=0.004). Greater arm muscle area was associated with faster run time, and the ability to perform more stands and squats in 15 s. Poorer vitamin D status was associated with the ability to perform more stands and squats. Lower tibia ultrasound Z score was associated with greater hand grip strength. Early growth and current body mass index had no associations with motor outcomes. Conclusions Current HAZ and arm muscle area showed the strongest associations with gross motor outcomes, likely due to a combination of simple physics and factors associated with stunting. The counterintuitive inverse associations of tibia health and vitamin D status with outcomes may require further research. PMID:26747034

Samuel D. Gross, the Writing of American Surgical History.

PubMed

Rutkow, Ira

2015-12-01

To explore the details of Samuel D. Gross's achievements as America's foremost historian of medicine in the mid-nineteenth century. The life of Samuel D. Gross, the most renowned of the nation's surgeons in the nineteenth century, has been extensively researched and celebrated. Despite the long-standing interest in Gross's accomplishments, there is an important and influential aspect of his career that has been forgotten. Gross was the country's first surgical historian and his boosting of the popular image of the knife bearer was crucial to shaping the future of the craft, in particular surgery's rise as a respected specialty within the whole of medicine. An analysis of the published medical literature and unpublished documents relating to Samuel D. Gross and his status as the country's earliest historian of surgery. At a time when surgery was not considered a separate branch of medicine but a mere technical mode of treatment, Gross's efforts in medical and surgical history provided a much needed boost to surgeons in their pursuit of self-confidence and self-respect. Although Gross's accomplishments as a medical historian have been overlooked, it is undeniable that he was America's pioneer surgical historian and, as such, afforded surgeons their earliest measure of self-esteem, a critical attribute that was indispensable for the rise of surgery as a distinguished profession.

26 CFR 1.832-1 - Gross income.

Code of Federal Regulations, 2014 CFR

2014-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-1 Gross income. (a) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in § 1.831-1 the..., remittances from the home office of a foreign insurance company to the United States branch, borrowed money...

26 CFR 1.832-1 - Gross income.

Code of Federal Regulations, 2013 CFR

2013-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-1 Gross income. (a) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in § 1.831-1 the..., remittances from the home office of a foreign insurance company to the United States branch, borrowed money...

26 CFR 1.832-1 - Gross income.

Code of Federal Regulations, 2011 CFR

2011-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-1 Gross income. (a) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in § 1.831-1 the..., remittances from the home office of a foreign insurance company to the United States branch, borrowed money...

26 CFR 1.832-1 - Gross income.

Code of Federal Regulations, 2012 CFR

2012-04-01

... TAXES (CONTINUED) Other Insurance Companies § 1.832-1 Gross income. (a) Gross income as defined in... under section 61, except that in the case of a mutual fire insurance company described in § 1.831-1 the..., remittances from the home office of a foreign insurance company to the United States branch, borrowed money...

BOREAS HYD-8 Gross Precipitation Data

NASA Technical Reports Server (NTRS)

Fernandes, Richard; Hall, Forrest G. (Editor); Knapp, David E. (Editor); Smith, David E. (Technical Monitor)

2000-01-01

The Boreal Ecosystem-Atmosphere Study (BOREAS) Hydrology (HYD)-08 team made measurements of surface hydrological processes at the Southern Study Area-Old Black Spruce (SSA-OBS) Tower Flux site to support its research into point hydrological processes and the spatial variation of these processes. Data collected may be useful in characterizing canopy interception, drip, throughfall, moss interception, drainage, evaporation, and capacity during the growing season at daily temporal resolution. This particular data set contains the gross precipitation measurements for July to August 1996. Gross precipitation is the precipitation that falls that is not intercepted by tree canopies. These data are stored in ASCII text files. The HYD-08 gross precipitation data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

Balancing Power Absorption Against Structural Loads With Viscous Drag and Power-Takeoff Efficiency Considerations

DOE PAGES

Tom, Nathan; Yu, Yi-Hsiang; Wright, Alan; ...

2017-11-17

The focus of this paper is to balance power absorption against structural loading for a novel fixed-bottom oscillating surge wave energy converter in both regular and irregular wave environments. The power-to-load ratio will be evaluated using pseudospectral control (PSC) to determine the optimum power-takeoff (PTO) torque based on a multiterm objective function. This paper extends the pseudospectral optimal control problem to not just maximize the time-averaged absorbed power but also include measures for the surge-foundation force and PTO torque in the optimization. The objective function may now potentially include three competing terms that the optimizer must balance. Separate weighting factorsmore » are attached to the surge-foundation force and PTO control torque that can be used to tune the optimizer performance to emphasize either power absorption or load shedding. To correct the pitch equation of motion, derived from linear hydrodynamic theory, a quadratic-viscous-drag torque has been included in the system dynamics; however, to continue the use of quadratic programming solvers, an iteratively obtained linearized drag coefficient was utilized that provided good accuracy in the predicted pitch motion. Furthermore, the analysis considers the use of a nonideal PTO unit to more accurately evaluate controller performance. The PTO efficiency is not directly included in the objective function but rather the weighting factors are utilized to limit the PTO torque amplitudes, thereby reducing the losses resulting from the bidirectional energy flow through a nonideal PTO. Results from PSC show that shedding a portion of the available wave energy can lead to greater reductions in structural loads, peak-to-average power ratio, and reactive power requirement.« less

NASA's Boeing 747 SCA with the Space Shuttle Endeavour on top climbs out after takeoff from Edwards

NASA Technical Reports Server (NTRS)

2001-01-01

NASA's modified Boeing 747 Shuttle Carrier Aircraft with the Space Shuttle Endeavour on top climbs out after takeoff from Edwards Air Force Base on the first leg of its ferry flight back to the Kennedy Space Center in Florida.

75 FR 39152 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-08

... Jackson, AL, Jackson Muni, RNAV (GPS) RWY 19, Orig Troy, AL, Troy Muni, ILS OR LOC RWY 7, Amdt 9 Troy, AL, Troy Muni, RNAV (GPS) RWY 7, Amdt 1 Troy, AL, Troy Muni, RNAV (GPS) RWY 25, Amdt 1 Vernon, AL, Lamar..., Amdt 1 East Troy, WI, East Troy Muni, Takeoff Minimums and Obstacle DP, Orig On June 09, 2010 (75 FR...

77 FR 3100 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-23

... on 8260-15A. The large number of SIAPs, Takeoff Minimums and ODPs, in addition to their complex... 31, Amdt 14 CANCELLED Cook, MN, Cook Muni, RNAV (GPS) RWY 13, Orig Cook, MN, Cook Muni, RNAV (GPS) RWY 31, Amdt 1 Ely, MN, Ely Muni, RNAV (GPS) RWY 12, Amdt 1 Ely, MN, Ely Muni, RNAV (GPS) RWY 30, Amdt...

78 FR 34561 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... regulatory evaluation as the anticipated impact is so minimal. For the same reason, the FAA certifies that... Airport FDC No. FDC Date Subject 6/27/13 NE Alliance Alliance Muni...... 2/3777 5/22/13 NDB RWY 12, Orig. 6/27/13 AK McGrath McGrath 2/7217 5/13/13 Takeoff Minimums and (Obstacle) DP, Amdt 2. 6/27/13 OR...

Association between gross motor function and nutritional status in children with cerebral palsy: a cross-sectional study from Colombia.

PubMed

Herrera-Anaya, Elizabeth; Angarita-Fonseca, Adriana; Herrera-Galindo, Víctor M; Martínez-Marín, Rocío D P; Rodríguez-Bayona, Cindy N

2016-09-01

To determine the association between gross motor function and nutritional status in children with cerebral palsy (CP) residing in an urban area in a developing country. We conducted a cross-sectional study in 177 children (ages 2-12y, 59.3% male) with a diagnosis of CP who were attending rehabilitation centres in Bucaramanga, Colombia (2012-2013). A physiotherapist evaluated patients using the Gross Motor Function Classification System (GMFCS, levels I to V). Nutritional status was evaluated by nutritionists and classified according to the World Health Organization growth charts. We used linear and multinomial logistic regression methods to determine the associations. There were 39.5%, 6.8%, 5.6%, 16.4%, and 31.6% patients classified in levels I to V respectively. The mean adjusted differences for weight-for-age, height-for-age, BMI-for-age, and height-for-weight z-scores were significantly larger for children classified in levels II to V compared with those in level I. The children classified in levels IV and V were more likely to have malnutrition (adjusted odds ratio [OR] 5.64; 95% confidence interval [CI] 2.27-14.0) and stunting (OR 8.42; 95% CI 2.90-24.4) than those classified in GMFCS levels I to III. Stunting and malnutrition are prevalent conditions among paediatric patients with CP, and both are directly associated with higher levels of gross motor dysfunction. © 2016 Mac Keith Press.

14 CFR Appendix I to Part 25 - Installation of an Automatic Takeoff Thrust Control System (ATTCS)

Code of Federal Regulations, 2010 CFR

2010-01-01

...) This appendix specifies additional requirements for installation of an engine power control system that... crew to increase thrust or power. I25.2Definitions. (a) Automatic Takeoff Thrust Control System (ATTCS... mechanical and electrical, that sense engine failure, transmit signals, actuate fuel controls or power levers...

Unmanned air vehicle: autonomous takeoff and landing

NASA Astrophysics Data System (ADS)

Lim, K. L.; Gitano-Briggs, Horizon Walker

2010-03-01

UAVs are increasing in popularity and sophistication due to the demonstrated performance which cannot be attained by manned aircraft1. These developments have been made possible by development of sensors, instrumentation, telemetry and controls during the last few decades. UAVs are now common in areas such as aerial observation and as communication relays3. Most UAVs, however, are still flown by a human pilot via remote control from a ground station. Even the existing autonomous UAVs often require a human pilot to handle the most difficult tasks of take off and landing2 (TOL). This is mainly because the navigation of the airplane requires observation, constant situational assessment and hours of experience from the pilot himself4. Therefore, an autonomous takeoff and landing system (TLS) for UAVs using a few practical design rules with various sensors, instrumentation, etc has been developed. This paper details the design and modeling of the UAV TLS. The model indicates that the UAV's TLS shows promising stability.

Unmanned air vehicle: autonomous takeoff and landing

NASA Astrophysics Data System (ADS)

Lim, K. L.; Gitano-Briggs, Horizon Walker

2009-12-01

UAVs are increasing in popularity and sophistication due to the demonstrated performance which cannot be attained by manned aircraft1. These developments have been made possible by development of sensors, instrumentation, telemetry and controls during the last few decades. UAVs are now common in areas such as aerial observation and as communication relays3. Most UAVs, however, are still flown by a human pilot via remote control from a ground station. Even the existing autonomous UAVs often require a human pilot to handle the most difficult tasks of take off and landing2 (TOL). This is mainly because the navigation of the airplane requires observation, constant situational assessment and hours of experience from the pilot himself4. Therefore, an autonomous takeoff and landing system (TLS) for UAVs using a few practical design rules with various sensors, instrumentation, etc has been developed. This paper details the design and modeling of the UAV TLS. The model indicates that the UAV's TLS shows promising stability.

29 CFR 794.122 - Ascertainment of “annual” gross sales volume.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Ascertainment of âannualâ gross sales volume. 794.122... Annual Gross Volume of Sales § 794.122 Ascertainment of “annual” gross sales volume. The annual gross volume of sales of an enterprise engaged in the wholesale or bulk distribution of petroleum products...

SR-71A - in Flight from Below at Takeoff

NASA Technical Reports Server (NTRS)

1997-01-01

Propulsion Laboratory in Pasadena, California. An upward-looking ultraviolet video camera placed in the SR-71's nosebay studied a variety of celestial objects in wavelengths that are blocked to ground-based astronomers. Earlier in its history, Dryden had a decade of past experience at sustained speeds above Mach 3. Two YF-12A aircraft and an SR-71 designated as a YF-12C were flown at the center between December 1969 and November 1979 in a joint NASA/USAF program to learn more about the capabilities and limitations of high-speed, high-altitude flight. The YF-12As were prototypes of a planned interceptor aircraft based on a design that later evolved into the SR-71 reconnaissance aircraft. Dave Lux was the NASA SR-71 project manger for much of the decade of the 1990s, followed by Steve Schmidt. Developed for the USAF as reconnaissance aircraft more than 30 years ago, SR-71s are still the world's fastest and highest-flying production aircraft. The aircraft can fly at speeds of more than 2,200 miles per hour (Mach 3+, or more than three times the speed of sound) and at altitudes of over 85,000 feet. The Lockheed Skunk Works (now Lockheed Martin) built the original SR-71 aircraft. Each aircraft is 107.4 feet long, has a wingspan of 55.6 feet, and is 18.5 feet high (from the ground to the top of the rudders, when parked). Gross takeoff weight is about 140,000 pounds, including a possible fuel weight of 80,280 pounds. The airframes are built almost entirely of titanium and titanium alloys to withstand heat generated by sustained Mach 3 flight. Aerodynamic control surfaces consist of all-moving vertical tail surfaces, ailerons on the outer wings, and elevators on the trailing edges between the engine exhaust nozzles. The two SR-71s at Dryden have been assigned the following NASA tail numbers: NASA 844 (A model), military serial 61-7980 and NASA 831 (B model), military serial 61-7956. From 1990 through 1994, Dryden also had another 'A' model, NASA 832, military serial 61-7971. This

Preliminary Study of the Fuel Saving Potential of Regenerative Turbofans for Commercial Subsonic Transports. [engine tests

NASA Technical Reports Server (NTRS)

Kraft, G. A.

1975-01-01

The fuel savings potential of regenerative turbofans was calculated and compared with that of a reference turbofan. At the design altitude of 10.67 km and Mach 0.80, the turbine-inlet-temperature of the regenerative turbofan was fixed at 1700 K while the overall pressure ratio was varied from 10 to 20. The fan pressure ratio was fixed at 1.6 and the bypass ratio varied from 8 to 10. The heat exchanger design parameters such as pressure drop and effectiveness varied from 4 to 8 percent and from 0.80 to 0.90, respectively. Results indicate a fuel savings due to regeneration of 4.1 percent and no change in takeoff gross weight.

P and W propulsion systems studies results/status

NASA Technical Reports Server (NTRS)

Smith, Martin G., Jr.; Champagne, George A.

1992-01-01

The topics covered include the following: Pratt and Whitney (P&W) propulsion systems studies - NASA funded efforts to date; P&W engine concepts; P&W combustor focus - rich burn quick quench (RBQQ) concept; mixer ejector nozzle concept - large flow entrainment reduces jet noise; technology impact on NO(x) emissions - mature RBQQ combustor reduces NO(x) up to 85 percent; technology impact on sideline noise characteristics of Mach 2.4 turbine bypass engines (TBE's) - 600 lb/sec airflow size; technology impact on takeoff gross weight (TOGW) - provides up to 12 percent TOGW reduction; HSCT quiet engine concepts; TBE inlet valve/ejector nozzle concept schematic; mixed flow turbofan study; and exhaust nozzle conceptual design.

Soil runway friction evaluation in support of USAF C-17 transport aircraft operations

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1995-01-01

A series of NASA Diagonal-Braked Vehicle (DBV) test runs were performed on the soil runway 7/25 at Holland landing zone, Fort Bragg, North Carolina, near Pope Air Force Base in March 1995 at the request of the Air Force C-17 System Program Office. These ground vehicle test results indicated that the dry runway friction level was suitable for planned C-17 transport aircraft landing and take-off operations at various gross weights. These aircraft operations were successfully carried out. On-board aircraft deceleration measurements were comparable to NASA DBV measurements. Additional tests conducted with an Army High Mobility Multi-Purpose Wheeled Vehicle equipped with a portable decelerometer, showed good agreement with NASA DBV data.

Preliminary design of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter aircraft

NASA Technical Reports Server (NTRS)

Cox, Brian; Borchers, Paul; Gomer, Charlie; Henderson, Dean; Jacobs, Tavis; Lawson, Todd; Peterson, Eric; Ross, Tweed, III; Bellmard, Larry

1990-01-01

The preliminary design study of a supersonic Short Takeoff and Vertical Landing (STOVL) fighter is presented. A brief historical survey of powered lift vehicles was presented, followed by a technology assessment of the latest supersonic STOVL engine cycles under consideration by industry and government in the U.S. and UK. A survey of operational fighter/attack aircraft and the modern battlefield scenario were completed to develop, respectively, the performance requirements and mission profiles for the study. Three configurations were initially investigated with the following engine cycles: a hybrid fan vectored thrust cycle, a lift+lift/cruise cycle, and a mixed flow vectored thrust cycle. The lift+lift/cruise aircraft configuration was selected for detailed design work which consisted of: (1) a material selection and structural layout, including engine removal considerations, (2) an aircraft systems layout, (3) a weapons integration model showing the internal weapons bay mechanism, (4) inlet and nozzle integration, (5) an aircraft suckdown prediction, (6) an aircraft stability and control analysis, including a takeoff, hover, and transition control analysis, (7) a performance and mission capability study, and (8) a life cycle cost analysis. A supersonic fighter aircraft with STOVL capability with the lift+lift/cruise engine cycle seems a viable option for the next generation fighter.

Water Stress Affects Development Time but Not Takeoff Performance in the Butterfly Pararge aegeria.

PubMed

Lailvaux, Simon P; Breuker, Casper J; Van Damme, Raoul

Most organisms are limited in the amount and type of resources they are able to extract from the environment. The juvenile environment is particularly important in this regard, as conditions over ontogeny can influence the adult phenotype. Whole-organism performance traits, such as locomotion, are susceptible to such environmental effects, yet the specific biotic and abiotic factors driving performance plasticity have received little attention. We tested whether speckled wood Pararge aegeria L. butterflies reared under conditions of water stress exhibited poorer flight morphology and performance than control individuals. Despite large differences in mortality between treatments, we found no effects of water stress treatment on takeoff performance and only minor treatment effects on flight morphology. However, butterflies reared on water-stressed diets exhibited both significantly greater mortality and longer development times than did control individuals. Pararge aegeria larvae may compensate for this stress by prolonging development, resulting in similar realized performance capacities at least in takeoff performance in surviving adult butterflies; other measures of flight performance remain to be considered. Alternatively, the adult phenotype may be insulated from environmental effects at the larval stage in these insects.

7 CFR 1400.501 - Determination of average adjusted gross income.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 10 2011-01-01 2011-01-01 false Determination of average adjusted gross income. 1400... PAYMENT ELIGIBILITY FOR 2009 AND SUBSEQUENT CROP, PROGRAM, OR FISCAL YEARS Average Adjusted Gross Income Limitation § 1400.501 Determination of average adjusted gross income. (a) Except as otherwise provided in...

Performance and technological feasibility of rocket powered HTHL-SSTO with take-off assist (aerospace plane/ekranoplane)

NASA Astrophysics Data System (ADS)

Tomita, Nobuyuki; Nebylov, Alexander V.; Sokolov, Victor V.; Ohkami, Yoshiaki

It might be said that it is common understanding that rocket-powered single stage to orbit (SSTO) aerospace planes will become feasible with near-term technology as described in [1] (Koelle, D. E. Survey and comparison of winged launch vehicle options, ISTS 94-g-11 V 1994) and [2] (Bekey, I. Why SSTO rocket launch vehicles are now feasible and practical, IAF-94-V.1.524 1994). Among two methods of launching aerospace planes into orbit, vertical take-off (VT) and horizontal take-off (HT), it seems that VT takes the lead from HT [1, 2]. The decision for the X-33 program by NASA, also, seems to favor VT. In retrospect, almost all of the launch vehicles in the past have been VT, mainly because VT solved the problem of exit from atmosphere to space. However, broadening the range of requirements for space transportation systems from military to commercial and unmanned to manned seems to favor the need for HT. In this paper, the authors are going to prove that aerospace plane/ekranoplane system, which is a reusable launch vehicle system based on the HT concept, with ekranoplane as a take-off and possibly, landing assist, could be competitive with the VT concept from both technological and economical view points. Ekranoplane is a wing-in-ground-effect craft (WIG), which moves at a speed of approximately 0.5 M, carrying heavy loads above the sea surface. Combination of high initial velocity and high performance tri-propellant engine for aerospace plane makes it possible to configure an aerospace plane which is competitive with VT. Other specific features of HT in comparison with VT are discussed.

Ground noise measurements during landing, take-off, and flyby operations of a four-engine turbopropeller STOL airplane

NASA Technical Reports Server (NTRS)

Hilton, D. A.; Henderson, H. R.; Maglieri, D. J.

1971-01-01

Noise measurements were obtained for a four-engine turbopropeller STOL airplane during a Federal Aviation Administration flight evaluation program at the National Aviation Facilities Experimental Center. These noise measurements involved landing-approach, takeoff-climbout, and flyby operations of the airplane. A total of 13 measuring positions were used to define the noise characteristics around a simulated STOL port. The results are presented in the form of both physical and subjective measurements. An appendix is included to present tabulated values of various subjective reaction units which may be significant for the planning and operation of STOL ports. The main source of noise produced by this vehicle was found to be the propeller, and noise levels decrease generally in accordance with the inverse-distance law for distances up to about 457 meters. For similar slant ranges, somewhat lower noise levels were experienced during flyby than during takeoff or landing.

VIDEO REVIEW: Maths in a Box video: Take-off - moving bodies with constant mass

NASA Astrophysics Data System (ADS)

Marks, Ken

1999-09-01

I write this review as a PGCE maths tutor, and therefore from the perspective of using parts of this series at A-level. The sample video, `Take-off - moving bodies with constant mass', is a good example of combining real footage with commentary as the viewer is invited to think about modelling the take-off of an aircraft. The style is reminiscent of Open University presentations and here the challenge is to determine the necessary length of the runway. The video is split into two sections. The first, commentary, section works quite well, although it jars a bit to hear Newton's Third Law put across as `Action and reaction are equal and opposite'; this is a familiar offering but one that still causes mystification in the sixth form. The viewer is invited to think about setting up equations, and reminded that the chain rule will be necessary to solve the differential equation generated from Newton's Second Law. This gives a good indication of the level of mathematics required. Unfortunately the flow is then somewhat disturbed by a strong emphasis on boundary conditions. If the student can cope with the general level of calculus required, this aspect of the challenge would also seem to fit more naturally into the second section of the video. This second section looks at setting up the equations and `solutions'. It can be used after classroom discussion, and takes the viewer through three, increasingly sophisticated, models involving functions for drag and resistance forces. On the whole this is clear and helpful, but for some reason the solutions each stop with an equation linking the length of the runway to the take-off velocity, failing to make use of the second equation to eliminate this intermediate variable. All in all, it is a useful addition to resources for A-level, particularly if students are also following the sort of mechanics syllabus (within mathematics) that emphasizes modelling.

Difference in children's gross motor skills between two types of preschools.

PubMed

Chow, Bik C; Louie, Lobo H T

2013-02-01

The purpose of this study was to assess the influence of preschool type (public vs private) on motor skill performance in 239 (121 boys, 118 girls) preschool children ages 3 to 6.5 yr. Preschoolers were tested on 12 fundamental motor skills from the Test of Gross Motor Development-Second Edition and 11 anthropometrics (body height, weight, Body Mass Index, waist and hip girths, and body segment lengths). Analysis of variance controlled for anthropometrics and age indicated that children from private preschools performed better on locomotor skills than those from public preschools. However, no difference was found in object control skills. The results suggest that performance of locomotor skills by preschool children is affected by their schools' physical environment.

A biomechanical analysis of the last stride, touch-down and take-off characteristics of the women's long jump.

PubMed

Lees, A; Fowler, N; Derby, D

1993-08-01

This study was concerned with the measurement of a selection of performance variables from competitors in the women's long jump final of the World Student Games held in Sheffield, UK in July 1991. Several performances of each of six finalists were recorded on cine-film at 100 Hz. Resulting planar kinematic data were obtained for the last stride, touch-down and take-off. For the analysis, the point of maximum knee flexion was established and this was used to represent the point at which the compression phase had ended. A variety of variables describing the position, velocity and angular changes are presented as descriptive data. In addition, these were used to compute energies on the basis of a whole body model. The data were interpreted on the basis of a technique model of long jumping established from the literature. It was confirmed that take-off velocity was a function of touch-down velocity, and that there was an increase in vertical velocity at the expense of a reduction of horizontal velocity. An attempt was made to identify the mechanisms acting during the touch-down to take-off phase which were responsible for generating vertical velocity. It was concluded that there was evidence for mechanical, biomechanical and muscular mechanisms. The former relates to the generation of vertical velocity by the body riding over the base of support; the second is the elastic re-utilization of energy; and the third is the contribution by concentric muscular contraction.

DC-9 flight demonstration program with refanned JT8D engines. Volume 4: Flyover noise

NASA Technical Reports Server (NTRS)

1975-01-01

Flyover noise tests were conducted to determine the noise reductions achievable by modifying the engines and nacelles of DC-9-30 airplanes. The two stage fan of the JT8D-9 engine was replaced with a larger diameter, single stage fan and sound absorbing materials were incorporated in the engines and nacelles. The noise levels were determined to be 95.3 EPNdB at the sideline, 96.2 EPNdB for a full thrust takeoff, 87.5 EPNdB for takeoff with thrust cutback, and 97.4 EPNdB for landing approach. The noise reductions relative to the hardwall JT8D-9 were 8.2 EPNdB for takeoff with cutback and 8.7 EPNdB for landing. The 90 EPNdB noise contour areas were reduced by 40% for missions requiring maximum design takeoff and landing weights. For typical mission weights, the reductions were 19% for full thrust takeoff and 34% for takeoff with cutback. The 95 EPNdB contour areas were reduced by 50% for takeoff and 30% for takeoff with cutback for both missions.

Psychiatric Symptoms in Children with Gross Motor Problems

ERIC Educational Resources Information Center

Emck, Claudia; Bosscher, Ruud J.; van Wieringen, Piet C. W.; Doreleijers, Theo; Beek, Peter J.

2012-01-01

Children with psychiatric disorders often demonstrate gross motor problems. This study investigates if the reverse also holds true by assessing psychiatric symptoms present in children with gross motor problems. Emotional, behavioral, and autism spectrum disorders (ASD), as well as psychosocial problems, were assessed in a sample of 40 children…

The Gross Motor Skills of Children with Mild Learning Disabilities

ERIC Educational Resources Information Center

Nonis, Karen P.; Jernice, Tan Sing Yee

2014-01-01

Many international studies have examined the gross motor skills of children studying in special schools while local studies of such nature are limited. This study investigated the gross motor skills of children with Mild Learning Disabilities (MLD; n = 14, M age = 8.93 years, SD = 0.33) with the Test of Gross Motor Development-2 (TGMD-2, Ulrich,…

Determination of optimal trajectories for an aircraft returning to the runway following a complete loss of thrust after takeoff

NASA Astrophysics Data System (ADS)

Gordon, Craig A.

This thesis examines the ability of a small, single-engine airplane to return to the runway following an engine failure shortly after takeoff. Two sets of trajectories are examined. One set of trajectories has the airplane fly a straight climb on the runway heading until engine failure. The other set of trajectories has the airplane perform a 90° turn at an altitude of 500 feet and continue until engine failure. Various combinations of wind speed, wind direction, and engine failure times are examined. The runway length required to complete the entire flight from the beginning of the takeoff roll to wheels stop following the return to the runway after engine failure is calculated for each case. The optimal trajectories following engine failure consist of three distinct segments: a turn back toward the runway using a large bank angle and angle of attack; a straight glide; and a reversal turn to align the airplane with the runway. The 90° turn results in much shorter required runway lengths at lower headwind speeds. At higher headwind speeds, both sets of trajectories are limited by the length of runway required for the landing rollout, but the straight climb cases generally require a lower angle of attack to complete the flight. The glide back to the runway is performed at an airspeed below the best glide speed of the airplane due to the need to conserve potential energy after the completion of the turn back toward the runway. The results are highly dependent on the rate of climb of the airplane during powered flight. The results of this study can aid the pilot in determining whether or not a return to the runway could be performed in the event of an engine failure given the specific wind conditions and runway length at the time of takeoff. The results can also guide the pilot in determining the takeoff profile that would offer the greatest advantage in returning to the runway.

Development of Rapid Radiochemical Method for Gross Alpha and Gross Beta Activity Concentration in Flowback and Produced Waters from Hydraulic Fracturing Operations

EPA Science Inventory

This report summarizes the development and validation of an improved method for the Determination of Gross Alpha and Gross Beta Activity in Flowback and Produced Waters from Hydraulic Fracturing Operations (FPWHFO). Flowback and produced waters are characterized by high concentra...

Effectiveness of catch basins equipped with hoods in retaining gross solids and hydrocarbons in highway runoff, Southeast Expressway, Boston, Massachusetts, 2008-09

USGS Publications Warehouse

Smith, Kirk P.

2011-01-01

Stormwater mobilizes litter and other debris along the roadway where it is transported to the highway drainage systems. Initial treatment for stormwater runoff typically is provided by catch basins in highway settings. Modification of catch basins to include hoods that cover the catch-basin outlet is intended to enhance catch-basin performance by retaining floatable debris and various hydrophobic organic compounds that tend to float on the water surface within the sump of the catch basin. The effectiveness of six deep-sump off-line catch basins equipped with hoods in reducing the mass of gross solids greater than 0.25 inches in diameter and concentrations of oil and grease (OG) and total petroleum hydrocarbons (TPH) was examined along the Southeast Expressway, in Boston, Massachusetts. Two deep-sump catch basins were equipped with cast-iron hoods. Three were equipped with molded plastic hoods, known as an Eliminator, and a single catch basin was equipped with a fiberglass anti-siphoning hood, known as a Snout. Samples of gross solids greater than 0.25 inches in diameter, excluding gravel and metallic materials, were routinely collected for a 6-month period from a collection structure mounted at the end of each catch-basin outlet pipe. After about 6 months, all floatable, saturated low-density and high-density solids were removed from each catch basin. In addition to the collection of samples of gross solids, samples of sump water from five catch basins and flow-weighted composite samples of stormwater from the outlet of one catch basin were collected and analyzed for concentrations of OG and TPH. A mass balance approach was used to assess the effectiveness of each catch basin equipped with a hood in retaining gross solids. The effectiveness of the deep-sump catch basins fitted with one of three types of hoods in retaining gross solids ranged from 27 to 52 percent. From 45 to 90 percent of the gross solids collected from the catch-basin sumps were composed of

Development of a Cross-Flow Fan Rotor for Vertical Take-Off and Landing Aircraft

DTIC Science & Technology

2013-06-01

ANSYS CFX , along with the commercial computer-aided design software SolidWorks, was used to model and perform a parametric study on the number of rotor...the results found using ANSYS CFX . The experimental and analytical models were successfully compared at speeds ranging from 4,000 to 7,000 RPM...will make vertical take-off possible. The commercial computational fluid dynamics software ANSYS CFX , along with the commercial computer-aided design

75 FR 65940 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-27

..., RNAV (RNP) RWY 32, Orig Portland, OR, Portland Intl, ILS OR LOC RWY 10R, ILS RWY 10R (SA CAT I), ILS RWY 10R (CAT II), ILS RWY 10R (CAT III), Amdt 33A Hondo, TX, Hondo Muni, Takeoff Minimums and Obstacle... Intl, ILS OR LOC RWY 3, ILS RWY 3 (SA CAT I), ILS RWY 3 (CAT II), ILS RWY 3 (CAT III), Amdt 6 Spokane...

75 FR 55961 - Standard Instrument Approach Procedures, and Takeoff Minimums and Obstacle Departure Procedures...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-15

.../1/10 LOC RWY 8, AMDT 5A. 21-Oct-10 AZ FORT HUACHUCA/ SIERRA VISTA MUNI- 0/5486 8/30/10 TAKEOFF MINIMUMS AND OBSTACLE DP, AMDT 2. SIERRA VISTA. LIBBY AAF. 21-Oct-10 LA LAKE CHARLES..... LAKE CHARLES RGNL... LOC/DME RWY 14, AMDT 8. 21-Oct-10 LA SLIDELL SLIDELL 0/7403 8/30/10 NDB RWY 36, ORIG-D. 21-Oct-10 FL...

Combining forecast weights: Why and how?

NASA Astrophysics Data System (ADS)

Yin, Yip Chee; Kok-Haur, Ng; Hock-Eam, Lim

2012-09-01

This paper proposes a procedure called forecast weight averaging which is a specific combination of forecast weights obtained from different methods of constructing forecast weights for the purpose of improving the accuracy of pseudo out of sample forecasting. It is found that under certain specified conditions, forecast weight averaging can lower the mean squared forecast error obtained from model averaging. In addition, we show that in a linear and homoskedastic environment, this superior predictive ability of forecast weight averaging holds true irrespective whether the coefficients are tested by t statistic or z statistic provided the significant level is within the 10% range. By theoretical proofs and simulation study, we have shown that model averaging like, variance model averaging, simple model averaging and standard error model averaging, each produces mean squared forecast error larger than that of forecast weight averaging. Finally, this result also holds true marginally when applied to business and economic empirical data sets, Gross Domestic Product (GDP growth rate), Consumer Price Index (CPI) and Average Lending Rate (ALR) of Malaysia.

Weight Status in the First 2 Years of Life and Neurodevelopmental Impairment in Extremely Low Gestational Age Newborns.

PubMed

Belfort, Mandy B; Kuban, Karl C K; O'Shea, T Michael; Allred, Elizabeth N; Ehrenkranz, Richard A; Engelke, Stephen C; Leviton, Alan

2016-01-01

To examine the extent to which weight gain and weight status in the first 2 years of life relate to the risk of neurodevelopmental impairment in extremely preterm infants. In a cohort of 1070 infants born between 23 and 27 weeks' gestation, we examined weight gain from 7-28 days of life (in quartiles) and weight z-score at 12 and 24 months corrected age (in 4 categories: <-2; ≥-2, <-1; ≥1, <1; and ≥1) in relation to these adverse neurodevelopmental outcomes: Bayley-II mental development index <55, Bayley-II psychomotor development index <55, cerebral palsy, Gross Motor Function Classification System ≥1 (cannot walk without assistance), microcephaly. We adjusted for confounders in logistic regression, stratified by sex, and performed separate analyses including the entire sample, and excluding children unable to walk without assistance (motor impairment). Weight gain in the lowest quartile from 7-28 days was not associated with higher risk of adverse outcomes. Children with a 12-month weight z-score <-2 were at increased risk for all adverse outcomes in girls, and for microcephaly and Gross Motor Function Classification System ≥1 in boys. However, excluding children with motor impairment attenuated all associations except that of weight z-score <-2 with microcephaly in girls. Similarly, most associations of low weight z-score at 24 months with adverse outcomes were attenuated with exclusion of children with motor impairment. Excluding children who have gross motor impairment appears to eliminate the association of low weight status with neurodevelopmental impairments at 2 years in extremely preterm infants. Copyright © 2016 Elsevier Inc. All rights reserved.

Effects of the kinematic viscosity and surface tension on the bubble take-off period in a catalase-hydrogen peroxide system.

PubMed

Sasaki, Satoshi; Iida, Yoshinori

2009-06-01

The effect of kinematic viscosity and surface tension of the solution was investigated by adding catalase, glucose oxidase, or glucose on the bubble movement in a catalase-hydrogen peroxide system. The kinematic viscosity was measured using a Cannon-Fenske kinematic viscometer. The surface tension of the solution was measured by the Wilhelmy method using a self-made apparatus. The effects of the hole diameter/cell wall thickness, catalase concentration, glucose concentration, and glucose oxidase concentration on the kinematic viscosity, surface tension, and bubble take-off period were investigated. With our system, the effects of the changes in the solution materiality on the bubble take-off period were proven to be very small in comparison to the change in the oxygen-producing rate.

Supplementation of diets containing pea meal with exogenous enzymes: effects on weight gain, feed conversion, nutrient digestibility and gross morphology of the gastrointestinal tract of growing broiler chicks.

PubMed

Cowieson, A J; Acamovic, T; Bedford, M R

2003-07-01

1. The potential for the nutritional improvement of pea-based diets by supplementation with a cocktail of exogenous carbohydrases was investigated using growing broiler chicks. 2. Pea meals (grown in the UK) were included in wheat-based diets at 300 g/kg as a partial replacement for an approximately isonitrogenous mixture of wheat and soybean meal. A wheat/soybean meal diet served as a control and each diet was supplemented with a cocktail of alpha-amylase, pectinase and cellulase. The diets were fed to 1-d-old broiler chicks for a period of 21 d. Weight gain and feed conversion were monitored weekly and excreta were collected during the final week in order to determine nutrient digestibility coefficients and metabolisable energy. On d 21, the gastrointestinal (GI) tract was excised and gross morphology measured. 3. Inclusion of pea meal reduced weight gain, feed conversion, nutrient digestibility and also increased the relative sizes of the distal sections of the GI tract. 4. Enzyme addition partially ameliorated the detrimental effects of pea meal inclusion although similar improvements were also noted for birds fed on the control diet. 5. It is concluded that the nutritive value of pea-meal-based diets can be improved by the addition of carbohydrases, and that some pea cultivars show considerable potential as vegetable protein sources for broiler chicks.

Take-Off Time of the First Generation of the Overwintering Small Brown Planthopper, Laodelphax striatellus in the Temperate Zone in East Asia

PubMed Central

Sanada-Morimura, Sachiyo; Otuka, Akira; Matsumura, Masaya; Etoh, Tomoki; Zhu, Yeqin; Zhou, Yijun; Zhang, Gufeng

2015-01-01

Overseas migration of the small brown planthopper, Laodelphax striatellus (Fallén), occurs during the winter wheat harvest season in East Asia. Knowing the take-off time of emigrating L. striatellus is crucial for predicting such migrations with a simulation technique because winds, carriers of migratory insects, change continuously. Several methods were used in China and Japan from late May to early June 2012 and again in 2013 to identify the precise timing of take-off. These methods included: a tow net trap mounted to a pole at 10 m above the ground, a helicopter-towed net trap, and a canopy trap (which also had video monitoring) set over wheat plants. Laodelphax striatellus emigrated from wheat fields mainly in the early evening, before dusk. The insects also emigrated during the daytime but rarely emigrated at dawn, showing a pattern that is unlike the bimodal emigration at dusk and dawn of two other rice planthoppers, the brown planthopper, Nilaparvata lugens (Stål), and the white-backed planthopper, Sogatella furcifera (Horváth). There was no significant difference in the temporal pattern of take-off behavior between females and males of Japanese L. striatellus populations. PMID:25780936

[The physical therapy undergraduate students' responses to the gross human anatomy subjects].

PubMed

Anahara, Reiko; Kawashiro, Yukiko; Matsuno, Yoshiharu; Mori, Chisato; Kohno, Toshihiko

2008-09-01

Instruction in gross human anatomy is one of the important items in the subject for co-medical students of the physical therapist course. The physical therapy undergraduate students are required to have a solid understanding of the structure and formation of the human body. Therefore, their good-understanding of the course on the gross human anatomy and their experience of the gross human anatomy laboratory (observation practice) are acquired to improve their knowledge of the human body. To clarify the student responses to the gross human anatomy course including the gross human anatomy laboratory, several questionnaires were administered to the freshman physical therapy undergraduate student for two years. We found that more than 80% of the students, who felt a negative attitude for gross human anatomy before the course started, had a positive attitude about the gross human anatomy after going through the course. The experience of the gross human anatomy laboratory increased the students' activity of learning and they thought more about the dignity of being human after the course than before viewing. In addition, the results suggested that the multiple experiences of the gross human anatomy course are useful for the physical therapy undergraduate students to improve the quality of their understanding of the human body.

Take-off engine particle emission indices for in-service aircraft at Los Angeles International Airport.

PubMed

Moore, Richard H; Shook, Michael A; Ziemba, Luke D; DiGangi, Joshua P; Winstead, Edward L; Rauch, Bastian; Jurkat, Tina; Thornhill, Kenneth L; Crosbie, Ewan C; Robinson, Claire; Shingler, Taylor J; Anderson, Bruce E

2017-12-19

We present ground-based, advected aircraft engine emissions from flights taking off at Los Angeles International Airport. 275 discrete engine take-off plumes were observed on 18 and 25 May 2014 at a distance of 400 m downwind of the runway. CO 2 measurements are used to convert the aerosol data into plume-average emissions indices that are suitable for modelling aircraft emissions. Total and non-volatile particle number EIs are of order 10 16 -10 17 kg -1 and 10 14 -10 16 kg -1 , respectively. Black-carbon-equivalent particle mass EIs vary between 175-941 mg kg -1 (except for the GE GEnx engines at 46 mg kg -1 ). Aircraft tail numbers recorded for each take-off event are used to incorporate aircraft- and engine-specific parameters into the data set. Data acquisition and processing follow standard methods for quality assurance. A unique aspect of the data set is the mapping of aerosol concentration time series to integrated plume EIs, aircraft and engine specifications, and manufacturer-reported engine emissions certifications. The integrated data enable future studies seeking to understand and model aircraft emissions and their impact on air quality.

Take-off engine particle emission indices for in-service aircraft at Los Angeles International Airport

PubMed Central

Moore, Richard H.; Shook, Michael A.; Ziemba, Luke D.; DiGangi, Joshua P.; Winstead, Edward L.; Rauch, Bastian; Jurkat, Tina; Thornhill, Kenneth L.; Crosbie, Ewan C.; Robinson, Claire; Shingler, Taylor J.; Anderson, Bruce E.

2017-01-01

We present ground-based, advected aircraft engine emissions from flights taking off at Los Angeles International Airport. 275 discrete engine take-off plumes were observed on 18 and 25 May 2014 at a distance of 400 m downwind of the runway. CO2 measurements are used to convert the aerosol data into plume-average emissions indices that are suitable for modelling aircraft emissions. Total and non-volatile particle number EIs are of order 1016–1017 kg−1 and 1014–1016 kg−1, respectively. Black-carbon-equivalent particle mass EIs vary between 175–941 mg kg−1 (except for the GE GEnx engines at 46 mg kg−1). Aircraft tail numbers recorded for each take-off event are used to incorporate aircraft- and engine-specific parameters into the data set. Data acquisition and processing follow standard methods for quality assurance. A unique aspect of the data set is the mapping of aerosol concentration time series to integrated plume EIs, aircraft and engine specifications, and manufacturer-reported engine emissions certifications. The integrated data enable future studies seeking to understand and model aircraft emissions and their impact on air quality. PMID:29257135

Take-off engine particle emission indices for in-service aircraft at Los Angeles International Airport

NASA Astrophysics Data System (ADS)

Moore, Richard H.; Shook, Michael A.; Ziemba, Luke D.; Digangi, Joshua P.; Winstead, Edward L.; Rauch, Bastian; Jurkat, Tina; Thornhill, Kenneth L.; Crosbie, Ewan C.; Robinson, Claire; Shingler, Taylor J.; Anderson, Bruce E.

2017-12-01

We present ground-based, advected aircraft engine emissions from flights taking off at Los Angeles International Airport. 275 discrete engine take-off plumes were observed on 18 and 25 May 2014 at a distance of 400 m downwind of the runway. CO2 measurements are used to convert the aerosol data into plume-average emissions indices that are suitable for modelling aircraft emissions. Total and non-volatile particle number EIs are of order 1016-1017 kg-1 and 1014-1016 kg-1, respectively. Black-carbon-equivalent particle mass EIs vary between 175-941 mg kg-1 (except for the GE GEnx engines at 46 mg kg-1). Aircraft tail numbers recorded for each take-off event are used to incorporate aircraft- and engine-specific parameters into the data set. Data acquisition and processing follow standard methods for quality assurance. A unique aspect of the data set is the mapping of aerosol concentration time series to integrated plume EIs, aircraft and engine specifications, and manufacturer-reported engine emissions certifications. The integrated data enable future studies seeking to understand and model aircraft emissions and their impact on air quality.

Treadmill training with partial body weight support compared with conventional gait training for low-functioning children and adolescents with nonspastic cerebral palsy: a two-period crossover study.

PubMed

Su, Ivan Y W; Chung, Kenny K Y; Chow, Daniel H K

2013-12-01

Partial body weight-supported treadmill training has been shown to be effective in gait training for patients with neurological disorders such as spinal cord injuries and stroke. Recent applications on children with cerebral palsy were reported, mostly on spastic cerebral palsy with single subject design. There is lack of evidence on the effectiveness of such training for nonspastic cerebral palsy, particularly those who are low functioning with limited intellectual capacity. This study evaluated the effectiveness of partial body weight-supported treadmill training for improving gross motor skills among these clients. A two-period randomized crossover design with repeated measures. A crossover design following an A-B versus a B-A pattern was adopted. The two training periods consisted of 12-week partial body weight-supported treadmill training (Training A) and 12-week conventional gait training (Training B) with a 10-week washout in between. Ten school-age participants with nonspastic cerebral palsy and severe mental retardation were recruited. The Gross Motor Function Measure-66 was administered immediately before and after each training period. Significant improvements in dimensions D and E of the Gross Motor Function Measure-66 and the Gross Motor Ability Estimator were obtained. Our findings revealed that the partial body weight-supported treadmill training was effective in improving gross motor skills for low-functioning children and adolescents with nonspastic cerebral palsy. .

46 CFR 69.117 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Spaces exempt from inclusion in gross tonnage. 69.117 Section 69.117 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND... inclusion in gross tonnage. (a) Purpose. This section lists spaces which are exempt from inclusion in gross...

46 CFR 69.117 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Spaces exempt from inclusion in gross tonnage. 69.117 Section 69.117 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND... inclusion in gross tonnage. (a) Purpose. This section lists spaces which are exempt from inclusion in gross...

46 CFR 69.117 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Spaces exempt from inclusion in gross tonnage. 69.117 Section 69.117 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DOCUMENTATION AND... inclusion in gross tonnage. (a) Purpose. This section lists spaces which are exempt from inclusion in gross...

26 CFR 1.872-1 - Gross income of nonresident alien individuals.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 9 2011-04-01 2011-04-01 false Gross income of nonresident alien individuals. 1...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Nonresident Aliens and Foreign Corporations § 1.872-1 Gross income of nonresident alien individuals. (a) In general—(1) Inclusions. The gross income of a...

26 CFR 1.872-1 - Gross income of nonresident alien individuals.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 9 2012-04-01 2012-04-01 false Gross income of nonresident alien individuals. 1...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Nonresident Aliens and Foreign Corporations § 1.872-1 Gross income of nonresident alien individuals. (a) In general—(1) Inclusions. The gross income of a...

26 CFR 1.872-1 - Gross income of nonresident alien individuals.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 9 2013-04-01 2013-04-01 false Gross income of nonresident alien individuals. 1...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Nonresident Aliens and Foreign Corporations § 1.872-1 Gross income of nonresident alien individuals. (a) In general—(1) Inclusions. The gross income of a...

26 CFR 1.872-1 - Gross income of nonresident alien individuals.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 9 2014-04-01 2014-04-01 false Gross income of nonresident alien individuals. 1...) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Nonresident Aliens and Foreign Corporations § 1.872-1 Gross income of nonresident alien individuals. (a) In general—(1) Inclusions. The gross income of a...

High Specific Stiffness Shafts and Advanced Bearing Coatings for Gas Turbine Engines Final Report CRADA No. TC-1089-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, Troy; Chin, Herbert

At the time of the CRADA, the largest in-service gas-turbine aircraft engines strove for increased thrust and power density to meet the requirements for take-off thrust, given the increase in take-off gross weight (TOGW) associated with longer range transport requirements. The trend in modem turbo shaft engines was toward turbine shafts with higher and higher length-to-diameter ratios, which reduced the shaft critical speed. Using co nventional shaft materials, this lead to shafts that needed to operate near or above sensitive shaft bending critical speeds, therefore requiring multiple bearings and/ or multiple squeeze-film dampers to control the dynamic response. Using newmore » materials and d esign concepts this project demonstrated the use of new shaft materials which could provide increased shaft speed range above existing maximum engine speeds without encountering a critic al speed event and high vector deflections. This increased main shaft speed also resulted in decreased bearing life associated with lower heat dissipation and higher centrifugal forces. Thus, a limited effort was devoted to feasibility of higher performance bearing coatings to mitigate the speed effects.« less

Curricular Guidelines in Gross Anatomy.

ERIC Educational Resources Information Center

Horn, Stanton D.; And Others

1981-01-01

An outline of AADS curricular guidelines for gross anatomy in dental education includes primary educational goals, prerequisites, core content, specific course objectives for each section of content, sequencing, faculty requirements, and facility and equipment needs. (MSE)

26 CFR 1.872-1 - Gross income of nonresident alien individuals.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Gross income of nonresident alien individuals. 1...) INCOME TAX (CONTINUED) INCOME TAXES Nonresident Aliens and Foreign Corporations § 1.872-1 Gross income of nonresident alien individuals. (a) In general—(1) Inclusions. The gross income of a nonresident alien...

Current usage and future trends in gross digital photography in Canada.

PubMed

Horn, Christopher L; DeKoning, Lawrence; Klonowski, Paul; Naugler, Christopher

2014-01-14

The purpose of this study was to assess the current usage, utilization and future direction of digital photography of gross surgical specimens in pathology laboratories across Canada. An online survey consisting of 23 multiple choice and free-text questions regarding gross digital photography was sent out to via email to laboratory staff across Canada involved in gross dissection of surgical specimens. Sixty surveys were returned with representation from most of the provinces. Results showed that gross digital photography is utilized at most institutions (90.0%) and the primary users of the technology are Pathologists (88.0%), Pathologists' Assistants (54.0%) and Pathology residents (50.0%). Most respondents felt that there is a definite need for routine digital imaging of gross surgical specimens in their practice (80.0%). The top two applications for gross digital photography are for documentation of interesting/ complex cases (98.0%) and for teaching purposes (84.0%). The main limitations identified by the survey group are storage space (42.5%) and security issues (40.0%). Respondents indicated that future applications of gross digital photography mostly include teaching (96.6%), presentation at tumour boards/ clinical rounds (89.8%), medico-legal documentation (72.9%) and usage for consultation purposes (69.5%). The results of this survey indicate that pathology staff across Canada currently utilizes gross digital images for regular documentation and educational reasons. They also show that the technology will be needed for future applications in teaching, consultation and medico-legal purposes.

Associations between gross motor skills and physical activity in Australian toddlers.

PubMed

Veldman, Sanne L C; Jones, Rachel A; Santos, Rute; Sousa-Sá, Eduarda; Pereira, João R; Zhang, Zhiguang; Okely, Anthony D

2018-08-01

Physical activity can be promoted by high levels of gross motor skills. A systematic review found a positive relationship in children (3-18 years) but only few studies examined this in younger children. The aim of this study was to examine the association between gross motor skills and physical activity in children aged 11-29 months. Cross-sectional study. This study involved 284 children from 30 childcare services in NSW, Australia (Mean age=19.77±4.18months, 53.2% boys). Physical activity was measured using accelerometers (Actigraph GT3X+). Gross motor skills were assessed using the Peabody Developmental Motor Scales Second Edition (PDMS-2). Multilevel linear regression analyses were computed to assess associations between gross motor skills and physical activity, adjusting for sex, age and BMI. Children spent 53.08% of their time in physical activity and 10.39% in moderate to vigorous physical activity (MVPA). Boys had higher total physical activity (p<0.01) and MVPA (p<0.01) than girls. The average gross motor skills score was 96.16. Boys scored higher than girls in object manipulation (p<0.001). There was no association between gross motor skills and total physical activity or MVPA. Although gross motor skills were not associated with physical activity in this sample, stronger associations are apparent in older children. This study therefore highlights a potential important age to promote gross motor skills. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Why does walking economy improve after weight loss in obese adolescents?

PubMed

Peyrot, Nicolas; Thivel, David; Isacco, Laurie; Morin, Jean-Benoît; Belli, Alain; Duche, Pascale

2012-04-01

This study tested the hypothesis that the increase in walking economy (i.e., decrease in net metabolic rate per kilogram) after weight loss in obese adolescents is induced by a lower metabolic rate required to support the lower body weight and maintain balance during walking. Sixteen obese adolescent boys and girls were tested before and after a weight reduction program. Body composition and oxygen uptake while standing and walking at four preset speeds (0.75, 1, 1.25, and 1.5 m·s⁻¹) and at the preferred speed were quantified. Net metabolic rate and gross metabolic cost of walking-versus-speed relationships were determined. A three-compartment model was used to distinguish the respective parts of the metabolic rate associated with standing (compartment 1), maintaining balance and supporting body weight during walking (compartment 2), and muscle contractions required to move the center of mass and limbs (compartment 3). Standing metabolic rate per kilogram (compartment 1) significantly increased after weight loss, whereas net metabolic rate per kilogram during walking decreased by 9% on average across speeds. Consequently, the gross metabolic cost of walking per unit of distance-versus-speed relationship and hence preferred walking speeds did not change with weight loss. Compartment 2 of the model was significantly lower after weight loss, whereas compartment 3 did not change. The model showed that the improvement in walking economy after weight loss in obese adolescents was likely related to the lower metabolic rate of the isometric muscular contractions required to support the lower body weight and maintain balance during walking. Contrastingly, the part of the total metabolic rate associated with muscle contractions required to move the center of mass and limbs did not seem to be related to the improvement in walking economy in weight-reduced individuals.

26 CFR 1.882-3 - Gross income of a foreign corporation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 9 2014-04-01 2014-04-01 false Gross income of a foreign corporation. 1.882-3... TAX (CONTINUED) INCOME TAXES (CONTINUED) Foreign Corporations § 1.882-3 Gross income of a foreign corporation. (a) In general—(1) Inclusions. The gross income of a foreign corporation for any taxable year...

46 CFR 69.169 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Spaces exempt from inclusion in gross tonnage. 69.169... MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Dual Measurement System § 69.169 Spaces exempt from inclusion in gross tonnage. The tonnage of the following spaces is exempt from inclusion in gross tonnage: (a) Spaces...

46 CFR 69.169 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Spaces exempt from inclusion in gross tonnage. 69.169... MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Dual Measurement System § 69.169 Spaces exempt from inclusion in gross tonnage. The tonnage of the following spaces is exempt from inclusion in gross tonnage: (a) Spaces...

46 CFR 69.169 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Spaces exempt from inclusion in gross tonnage. 69.169... MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Dual Measurement System § 69.169 Spaces exempt from inclusion in gross tonnage. The tonnage of the following spaces is exempt from inclusion in gross tonnage: (a) Spaces...

46 CFR 69.169 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Spaces exempt from inclusion in gross tonnage. 69.169... MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Dual Measurement System § 69.169 Spaces exempt from inclusion in gross tonnage. The tonnage of the following spaces is exempt from inclusion in gross tonnage: (a) Spaces...

46 CFR 69.169 - Spaces exempt from inclusion in gross tonnage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Spaces exempt from inclusion in gross tonnage. 69.169... MEASUREMENT OF VESSELS MEASUREMENT OF VESSELS Dual Measurement System § 69.169 Spaces exempt from inclusion in gross tonnage. The tonnage of the following spaces is exempt from inclusion in gross tonnage: (a) Spaces...

Tensorial Gross-Neveu models

NASA Astrophysics Data System (ADS)

Benedetti, Dario; Carrozza, Sylvain; Gurau, Razvan; Sfondrini, Alessandro

2018-01-01

We define and study various tensorial generalizations of the Gross-Neveu model in two dimensions, that is, models with four-fermion interactions and G 3 symmetry, where we take either G = U( N) or G = O( N). Such models can also be viewed as two-dimensional generalizations of the Sachdev-Ye-Kitaev model, or more precisely of its tensorial counterpart introduced by Klebanov and Tarnopolsky, which is in part our motivation for studying them. Using the Schwinger-Dyson equations at large- N, we discuss the phenomenon of dynamical mass generation and possible combinations of couplings to avoid it. For the case G = U( N),we introduce an intermediate field representation and perform a stability analysis of the vacua. It turns out that the only apparently viable combination of couplings that avoids mass generation corresponds to an unstable vacuum. The stable vacuum breaks U( N)3 invariance, in contradiction with the Coleman-Mermin-Wagner theorem, but this is an artifact of the large- N expansion, similar to the breaking of continuous chiral symmetry in the chiral Gross-Neveu model.

Benefits of advanced propulsion technology for the advanced supersonic transport

NASA Technical Reports Server (NTRS)

Hines, R. W.; Sabatella, J. A.

1973-01-01

Future supersonic transports will have to provide improvement in the areas of economics, range, and emissions relative to the present generation of supersonic transports, as well as meeting or improving upon FAR 36 noise goals. This paper covers the promising propulsion systems including variable-cycle engine concepts for long-range supersonic commercial transport application. The benefits of applying advanced propulsion technology to solve the economic and environmental problems are reviewed. The advanced propulsion technologies covered are in the areas of structures, materials, cooling techniques, aerodynamics, variable engine geometry, jet noise suppressors, acoustic treatment, and low-emission burners. The results of applying the advanced propulsion technology are presented in terms of improvement in overall system takeoff gross weight and return on investment.

High performance dash on warning air mobile, missile system. [intercontinental ballistic missiles - systems analysis

NASA Technical Reports Server (NTRS)

Levin, A. D.; Castellano, C. R.; Hague, D. S.

1975-01-01

An aircraft-missile system which performs a high acceleration takeoff followed by a supersonic dash to a 'safe' distance from the launch site is presented. Topics considered are: (1) technological feasibility to the dash on warning concept; (2) aircraft and boost trajectory requirements; and (3) partial cost estimates for a fleet of aircraft which provide 200 missiles on airborne alert. Various aircraft boost propulsion systems were studied such as an unstaged cryogenic rocket, an unstaged storable liquid, and a solid rocket staged system. Various wing planforms were also studied. Vehicle gross weights are given. The results indicate that the dash on warning concept will meet expected performance criteria, and can be implemented using existing technology, such as all-aluminum aircraft and existing high-bypass-ratio turbofan engines.

Study of turbine bypass remote augmentor lift system for V/STOL aircraft

NASA Technical Reports Server (NTRS)

Sheridan, A. E.

1985-01-01

The airframe design and engine/aircraft integration were emphasized in a NASA comparative study of turbofan and turbine bypass engine (TBE) with remote augmentor lift systems (RALS) for supersonic V/STOL aircraft. Functional features of the TBE are reviewed, noting the enhanced cycle efficiency and reduced afterbody drag compared to the turbojets. The present studies examied performance levels for aircraft with fleet defense and secondary anti-surface warfare roles, carrying AMRAAM and AIM missiles. TBE engine cycles were configured for hover and up-and-away flight from deck launch, and all tests were done from a conceptual design viewpoint. The results indicate that the TBE-RALS is superior to turbofan-RALS aircraft in both gross take-off weight and life cycle cost.

Interaction of the elytra and hind wing of a rhinoceros beetle (Trypoxylus dichotomus) during a take-off mode

NASA Astrophysics Data System (ADS)

Oh, Seungyoung; Oh, Sehyeong; Choi, Haecheon; Lee, Boogeon; Park, Hyungmin; Kim, Sun-Tae

2015-11-01

The elytra are a pair of hardened wings that cover the abdomen of a beetle to protect beetle's hind wings. During the take-off, these elytra open and flap in phase with the hind wings. We investigate the effect of the elytra flapping on beetle's aerodynamic performance. Numerical simulations are performed at Re=10,000 (based on the wingtip mean velocity and mean chord length of the hind wing) using an immersed boundary method. The simulations are focused on a take-off, and the wing kinematics used is directly obtained from the experimental observations using high speed cameras. The simulation result shows three-dimensional vortical structures generated by the hind wing of the beetle and their interaction with the elytra. The presence of elytra has a negative effect on the lift generation by the hind wings, but the lift force on the elytra themselves is negligible. Further discussions on the elytra - hind wing interaction will be provided during the presentation. Supported by UD130070ID.

Data Visualization of Invisible Airflow Hazards During Helicopter Takeoff and Landing Operations

NASA Technical Reports Server (NTRS)

Aragon, Cecilia R.

2004-01-01

Many aircraft accidents each year are caused by encounters with unseen airflow hazards near the ground such as vortices, downdrafts, wind shear, microbursts, or other turbulence. While such hazards frequently pose problems to fixed-wing airplanes, they are especially dangerous to helicopters, which often have to operate in confined spaces and under operationally stressful conditions. We are developing flight-deck visualizations of airflow hazards during helicopter takeoff and landing operations, and are evaluating their effectiveness with usability studies. Our hope is.that this work will lead to the production of an airflow hazard detection system for pilots that will save lives.

The Gross Anatomy Course: An Analysis of Its Importance

ERIC Educational Resources Information Center

Bockers, Anja; Jerg-Bretzke, Lucia; Lamp, Christoph; Brinkmann, Anke; Traue, Harald C.; Bockers, Tobias M.

2010-01-01

The gross anatomy dissection course is a cost-intensive piece of undergraduate medical education that students and professionals alike describe as very important within the overall medical curriculum. We sought to understand more explicitly students' valuation of gross anatomy as an "important" course and so developed a quantitative…

77 FR 1629 - Authorization To Use Lower Than Standard Takeoff, Approach and Landing Minimums at Military and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-11

... is not prepared. Such a determination has been made for this direct final rule. The reasoning for... guidance to pilots making an IFR takeoff or approach and landing at a military or foreign airport. Under... determination, and the reasoning should be clear. As noted above, the proposed changes to Sec. 135.225(f) are...

Cerebral palsy in Victoria: motor types, topography and gross motor function.

PubMed

Howard, Jason; Soo, Brendan; Graham, H Kerr; Boyd, Roslyn N; Reid, Sue; Lanigan, Anna; Wolfe, Rory; Reddihough, Dinah S

2005-01-01

To study the relationships between motor type, topographical distribution and gross motor function in a large, population-based cohort of children with cerebral palsy (CP), from the State of Victoria, and compare this cohort to similar cohorts from other countries. An inception cohort was generated from the Victorian Cerebral Palsy Register (VCPR) for the birth years 1990-1992. Demographic information, motor types and topographical distribution were obtained from the register and supplemented by grading gross motor function according to the Gross Motor Function Classification System (GMFCS). Complete data were obtained on 323 (86%) of 374 children in the cohort. Gross motor function varied from GMFCS level I (35%) to GMFCS level V (18%) and was similar in distribution to a contemporaneous Swedish cohort. There was a fairly even distribution across the topographical distributions of hemiplegia (35%), diplegia (28%) and quadriplegia (37%) with a large majority of young people having the spastic motor type (86%). The VCPR is ideal for population-based studies of gross motor function in children with CP. Gross motor function is similar in populations of children with CP in developed countries but the comparison of motor types and topographical distribution is difficult because of lack of consensus with classification systems. Use of the GMFCS provides a valid and reproducible method for clinicians to describe gross motor function in children with CP using a universal language.

Guidelines for Standard Photography in Gross and Clinical Anatomy

ERIC Educational Resources Information Center

Barut, Cagatay; Ertilav, Hakan

2011-01-01

Photography has a widespread usage in medicine and anatomy. In this review, authors focused on the usage of photography in gross and clinical anatomy. Photography in gross and clinical anatomy is not only essential for accurate documentation of morphological findings but also important in sharing knowledge and experience. Photographs of cadavers…

26 CFR 1.993-6 - Definition of gross receipts.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 10 2010-04-01 2010-04-01 false Definition of gross receipts. 1.993-6 Section 1.993-6 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Domestic International Sales Corporations § 1.993-6 Definition of gross receipts. (a...

46 CFR 69.119 - Spaces deducted from gross tonnage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Spaces deducted from gross tonnage. 69.119 Section 69... VESSELS MEASUREMENT OF VESSELS Standard Measurement System § 69.119 Spaces deducted from gross tonnage. (a) Purpose. This section lists the requirements for spaces (other than propelling machinery spaces under § 69...

Balancing the Power-to-Load Ratio for a Novel Variable Geometry Wave Energy Converter with Nonideal Power Take-Off in Regular Waves: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tom, Nathan M; Yu, Yi-Hsiang; Wright, Alan D

This work attempts to balance power absorption against structural loading for a novel variable geometry wave energy converter. The variable geometry consists of four identical flaps that will be opened in ascending order starting with the flap closest to the seafloor and moving to the free surface. The influence of a pitch motion constraint on power absorption when utilizing a nonideal power take-off (PTO) is examined and found to reduce the losses associated with bidirectional energy flow. The power-to-load ratio is evaluated using pseudo-spectral control to determine the optimum PTO torque based on a multiterm objective function. The pseudo-spectral optimalmore » control problem is extended to include load metrics in the objective function, which may now consist of competing terms. Separate penalty weights are attached to the surge-foundation force and PTO control torque to tune the optimizer performance to emphasize either power absorption or load shedding. PTO efficiency is not included in the objective function, but the penalty weights are utilized to limit the force and torque amplitudes, thereby reducing losses associated with bidirectional energy flow. Results from pseudo-spectral control demonstrate that shedding a portion of the available wave energy can provide greater reductions in structural loads and reactive power.« less

Update of aircraft profile data for the Integrated Noise Model computer program, vol. 2 : appendix A aircraft takeoff and landing profiles

DOT National Transportation Integrated Search

1992-03-01

This report provides aircraft takeoff and landing profiles, aircraft aerodynamic performance coefficients and engine performance coefficients for the aircraft data base (Database 9) in the Integrated Noise Model (INM) computer program. Flight profile...

Design of a Low Cost Short Takeoff-vertical Landing Export Fighter/attack Aircraft

NASA Technical Reports Server (NTRS)

Belcher, Anne; Bodeker, Dan, III; Miu, Steve; Petro, Laura; Senf, Cary Taylor; Woeltjen, Donald

1990-01-01

The design of a supersonic short takeoff and vertical landing (STOVL) aircraft is presented that is suitable for export. An advanced four poster, low bypass turbofan engine is to be used for propulsion. Preliminary aerodynamic analysis is presented covering a determination of CD versus CL, CD versus Mach number, as well as best cruise Mach number and altitude. Component locations are presented and center of gravity determined. Cost minimization is achieved through the use of developed subsystems and standard fabrication techniques using nonexotic materials. Conclusions regarding the viability of the STOVL design are presented.

29 CFR 794.120 - Meaning of “annual gross volume of sales.”

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Meaning of âannual gross volume of sales.â 794.120 Section... of Sales § 794.120 Meaning of “annual gross volume of sales.” The annual gross volume of sales of an... gross volume derived from all sales transactions is included, and will embrace among other things...

26 CFR 1.199-3 - Domestic production gross receipts.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 3 2011-04-01 2011-04-01 false Domestic production gross receipts. 1.199-3 Section 1.199-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations (continued) § 1.199-3 Domestic production gross...

26 CFR 1.199-3 - Domestic production gross receipts.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 3 2014-04-01 2014-04-01 false Domestic production gross receipts. 1.199-3 Section 1.199-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations (continued) § 1.199-3 Domestic production gross...

26 CFR 1.199-3 - Domestic production gross receipts.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 26 Internal Revenue 3 2013-04-01 2013-04-01 false Domestic production gross receipts. 1.199-3 Section 1.199-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations (continued) § 1.199-3 Domestic production gross...

26 CFR 1.199-3 - Domestic production gross receipts.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 3 2012-04-01 2012-04-01 false Domestic production gross receipts. 1.199-3 Section 1.199-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Itemized Deductions for Individuals and Corporations (continued) § 1.199-3 Domestic production gross...

Effect of surfactants on weight gain in mice.

PubMed

Kaneene, J B; Ross, R W

1986-03-01

A study was conducted to determine if four surfactants can induce increased weight gain in the mouse. Basic-H, Triton X-100, Amway All Purpose Adjuvant and X-77 were put in water and fed to various groups of ICR 21 day old female mice for a period of 43 days. All the mice were clinically normal throughout the study period. Pathological examination of a random sample of the mice revealed no gross pathological changes. Similarly, histopathological examination of the lungs, livers and intestines did not reveal any visible lesions. Basic-H and Amway surfactants induced weight gain, though not significantly, better at 0.1% (V/V) concentration while X-77 and Triton X-100 induced weight gain better at 0.4% (V/V) concentration. Overall results show that none of the surfactants tested induced significant weight gain.

NASA's Boeing 747 SCA with the Space Shuttle Endeavour on top climbs out after takeoff from Edwards Air Force Base

NASA Image and Video Library

2001-05-08

NASA's modified Boeing 747 Shuttle Carrier Aircraft with the Space Shuttle Endeavour on top climbs out after takeoff from Edwards Air Force Base on the first leg of its ferry flight back to the Kennedy Space Center in Florida.

26 CFR 1.199-3 - Domestic production gross receipts.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 3 2010-04-01 2010-04-01 false Domestic production gross receipts. 1.199-3 Section 1.199-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Itemized Deductions for Individuals and Corporations (continued) § 1.199-3 Domestic production gross receipts. (a) In...

Oropharyngeal dysphagia and gross motor skills in children with cerebral palsy.

PubMed

Benfer, Katherine A; Weir, Kelly A; Bell, Kristie L; Ware, Robert S; Davies, Peter S W; Boyd, Roslyn N

2013-05-01

To determine the prevalence of oropharyngeal dysphagia (OPD) and its subtypes (oral phase, pharyngeal phase, saliva control), and their relationship to gross motor functional skills in preschool children with cerebral palsy (CP). It was hypothesized that OPD would be present across all gross motor severity levels, and children with more severe gross motor function would have increased prevalence and severity of OPD. Children with a confirmed diagnosis of CP, 18 to 36 months corrected age, born in Queensland between 2006 and 2009, participated. Children with neurodegenerative conditions were excluded. This was a cross-sectional population-based study. Children were assessed by using 2 direct OPD measures (Schedule for Oral Motor Assessment; Dysphagia Disorders Survey), and observations of signs suggestive of pharyngeal phase impairment and impaired saliva control. Gross motor skills were described by using the Gross Motor Function Measure, Gross Motor Function Classification System (GMFCS), Manual Ability Classification System, and motor type/ distribution. OPD was prevalent in 85% of children with CP, and there was a stepwise relationship between OPD and GMFCS level. There was a significant increase in odds of having OPD, or a subtype, for children who were nonambulant (GMFCS V) compared with those who were ambulant (GMFCS I) (odds ratio = 17.9, P = .036). OPD was present across all levels of gross motor severity using direct assessments. This highlights the need for proactive screening of all young children with CP, even those with mild impairments, to improve growth and nutritional outcomes and respiratory health.

Anselm's Discovery of the Gross-Neveu Model in 1958

NASA Astrophysics Data System (ADS)

Shifman, M.

2013-06-01

The Gross-Neveu model comprises quantum field theory of N Dirac fermions interacting via four-fermion interaction in one spatial and one time dimension. It was introduced in 1974 (shortly after quantum chromodynamics was discovered) by David Gross and André Neveu [1] as a toy model which mimics two crucial features of quantum chromodynamics: asymptotic freedom and spontaneous breaking of a chiral symmetry. The model is based on N Dirac (i.e. complex two-component) fermions, ψ1, ψ2, ..., ψN. The Lagrangian of the Gross-Neveau model is [ {L} = bar{psi}ipartial_{mu}gamma^{mu}psi + frac{g^{2}}{2}(sumlimits_{k = 1}^{N}bar{psi}_{k}psi^{k})^{2}.

Vertical Takeoff and Landing Vehicle with Increased Cruise Efficiency

NASA Technical Reports Server (NTRS)

Langford, William M. (Inventor); Hodges, William T. (Inventor); Laws, Christopher T. (Inventor); Johns, Zachary R. (Inventor); Fredericks, William J. (Inventor); Moore, Mark D. (Inventor); Busan, Ronald C. (Inventor); Rothhaar, Paul M. (Inventor); North, David D. (Inventor); Webb, Sandy R. (Inventor)

2018-01-01

Systems, methods, and devices are provided that combine an advance vehicle configuration, such as an advanced aircraft configuration, with the infusion of electric propulsion, thereby enabling a four times increase in range and endurance while maintaining a full vertical takeoff and landing ("VTOL") and hover capability for the vehicle. Embodiments may provide vehicles with both VTOL and cruise efficient capabilities without the use of ground infrastructure. An embodiment vehicle may comprise a wing configured to tilt through a range of motion, a first series of electric motors coupled to the wing and each configured to drive an associated wing propeller, a tail configured to tilt through the range of motion, a second series of electric motors coupled to the tail and each configured to drive an associated tail propeller, and an electric propulsion system connected to the first series of electric motors and the second series of electric motors.

Phase III gross solids removal devices pilot study, 2002-2005.

DOT National Transportation Integrated Search

2005-12-01

The objective of the Phase III Gross Solids Removal Devices (GSRDs) Pilot study was to : evaluate the performance of non-proprietary devices that can capture gross solids and that can be : incorporated into existing highway drainage systems or implem...