Multiple Independent File Parallel I/O with HDF5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, M. C.

2016-07-13

The HDF5 library has supported the I/O requirements of HPC codes at Lawrence Livermore National Labs (LLNL) since the late 90’s. In particular, HDF5 used in the Multiple Independent File (MIF) parallel I/O paradigm has supported LLNL code’s scalable I/O requirements and has recently been gainfully used at scales as large as O(10 6) parallel tasks.

[Specialist's training for laparoscopic surgery in Wet-lab educational operating theatre].

PubMed

Khubezov, D A; Sazhin, V P; Ogoreltsev, A Yu; Puchkov, D K; Rodimov, S V; Ignatov, I S; Tazina, T V; Evsyukova, M A

2018-01-01

To develop system for students training in laparoscopic surgery by using of Wet-lab educational operating theatre. We have launched laparoscopic surgery teaching program for students of Ryazan State Medical University. This system includes several stages. At the first stage professional selection was carried out on 'dry' laparoscopic simulators among III-IV-year students of medical faculty. So, 10 people were selected. The second stage included theoretical and practical parts consisting of development of basic laparoscopic skills on 'dry' simulators. 5 students who scored the maximum points were admitted to the next stage. The third stage is working in Wet-lab operating theatre with a mentor. There were 10 sessions on 10 laboratory pigs. Final stage of our study compares two groups of participants: main group - 5 students who underwent above-described program and control group of 5 residents without experience for laparoscopic operations. The participants of the main group had significantly higher OSATS score compared with another group (20 vs. 10; p<0.05). Movements effectiveness estimated by measuring of movements trajectory total length was also higher in main group than in control group (6 vs. 20; p<0.05). Experts' subjective assessment according to 10-point scale was also higher for students than for interns (9 vs. 5, p<0.05). Participants in the main group required significantly less time to complete the task compared with the control group (40 vs. 90 minutes, p<0.05). Our experience has shown that training system with Wet-lab operating theatre is effective for quick and efficient training of medical students in main laparoscopic procedures. In our opinion, introduction of students into 'advanced' surgery from early age will make it possible to get finally highly professional specialists.

Specifications and Prototype of the Knowledge Repository (V.3.0) and the Knowledge Mediator (V.3.0)

ERIC Educational Resources Information Center

Andreou, Dimitris; Christophides, Vassilis; Flouris, Giorgos; Kotzinos, Dimitris; Pediaditis, Panagiotis; Tsialiamanis, Petros

2009-01-01

This deliverable reports the technical and research development performed until M36 (January 2009) within tasks T5.2 and T5.4 of WP5 in the KP-Lab project, per the latest Description of Work (DoW) 3.2 [DoW3.2]. The described components are included in the KP-Lab Semantic Web Knowledge Middleware (SWKM) Prototype Release 3.0 software that takes…

Recent advances in particle and droplet manipulation for lab-on-a-chip devices based on surface acoustic waves.

PubMed

Wang, Zhuochen; Zhe, Jiang

2011-04-07

Manipulation of microscale particles and fluid liquid droplets is an important task for lab-on-a-chip devices for numerous biological researches and applications, such as cell detection and tissue engineering. Particle manipulation techniques based on surface acoustic waves (SAWs) appear effective for lab-on-a-chip devices because they are non-invasive, compatible with soft lithography micromachining, have high energy density, and work for nearly any type of microscale particles. Here we review the most recent research and development of the past two years in SAW based particle and liquid droplet manipulation for lab-on-a-chip devices including particle focusing and separation, particle alignment and patterning, particle directing, and liquid droplet delivery.

Commerce lab: Mission analysis and payload integration study

NASA Technical Reports Server (NTRS)

1984-01-01

Conceived as one or more arrays of carriers which would fly aboard space shuttle, Commerce Lab can provide a point of focus for implementing a series of shuttle flights, co-sponsored by NASA and U.S. domestic concerns, for performing materials processing in research and pre-commercial investigations. As an orbiting facility for testing, developing, and implementing hardware and procedures, Commerce Lab can enhance space station development and hasten space platform production capability. Tasks considered include: (1) synthesis of user requirements and identification of common element and voids; (2) definition of performance and infrastructure requirement and alternative approaches; and (3) carrier, mission model, and infrastructure development.

The Role of Coping and Race in Healthy Children’s Experimental Pain Responses

PubMed Central

Evans, Subhadra; Lu, Qian; Tsao, Jennie C. I.; Zelter, Lonnie K.

2009-01-01

This study examined the relationship between race, laboratory-based coping strategies and anticipatory anxiety and pain intensity for cold, thermal (heat) and pressure experimental pain tasks. Participants were 123 healthy children and adolescents, including 33 African Americans (51% female; mean age =13.9 years) and 90 Caucasians (50% female; mean age = 12.6 years). Coping in response to the cold task was assessed with the Lab Coping Style interview; based on their interview responses, participants were categorized as ‘attenders’ (i.e., those who focused on the task) vs. ‘distractors’ (i.e., those who distracted themselves during the task). Analysis of covariance (ANCOVA) revealed significant interactions between race (African-American vs. Caucasian) and lab-based coping style after controlling for sex, age and socioeconomic status. African-American children classified as attenders reported less anticipatory anxiety for the cold task and lower pain intensity for the cold, heat and pressure tasks compared to those categorized as distractors. For these pain outcomes, Caucasian children classified as distractors reported less anticipatory anxiety and lower pain intensity relative to those categorized as attenders. The findings point to the moderating effect of coping in the relationship between race and experimental pain sensitivity. PMID:20352035

A study on the effect of varying sequence of lab performance skills on lab performance of high school physics students

NASA Astrophysics Data System (ADS)

Bournia-Petrou, Ethel A.

The main goal of this investigation was to study how student rank in class, student gender and skill sequence affect high school students' performance on the lab skills involved in a laboratory-based inquiry task in physics. The focus of the investigation was the effect of skill sequence as determined by the particular task. The skills considered were: Hypothesis, Procedure, Planning, Data, Graph, Calculations and Conclusion. Three physics lab tasks based on the simple pendulum concept were administered to 282 Regents physics high school students. The reliability of the designed tasks was high. Student performance was evaluated on individual student written responses and a scoring rubric. The tasks had high discrimination power and were of moderate difficulty (65%). It was found that, student performance was weak on Conclusion (42%), Hypothesis (48%), and Procedure (51%), where the numbers in parentheses represent the mean as a percentage of the maximum possible score. Student performance was strong on Calculations (91%), Data (82%), Graph (74%) and Plan (68%). Out of all seven skills, Procedure had the strongest correlation (.73) with the overall task performance. Correlation analysis revealed some strong relationships among the seven skills which were grouped in two distinct clusters: Hypothesis, Procedure and Plan belong to one, and Data, Graph, Calculations, and Conclusion belong to the other. This distinction may indicate different mental processes at play within each skill cluster. The effect of student rank was not statistically significant according to the MANOVA results due to the large variation of rank levels among the participating schools. The effect of gender was significant on the entire test because of performance differences on Calculations and Graph, where male students performed better than female students. Skill sequence had a significant effect on the skills of Procedure, Plan, Data and Conclusion. Students are rather weak in proposing a sensible, detailed procedure for the inquiry task which involves the "novel" concept. However they perform better on Procedure and Plan, if the "novel" task is not preceded by another, which explicitly offers step-by-step procedure instructions. It was concluded that the format of detailed, structured instructions often adopted by many commercial and school-developed lab books and conventional lab practices, fails to prepare students to propose a successful, detailed procedure when faced with a slightly "novel", lab-based inquiry task. Student performance on Data collection was higher in the tasks that involved the more familiar experimental arrangement than in the tasks using the slightly "novel" equipment. Student performance on Conclusion was better in tasks where they had to collect the Data themselves than in tasks, where all relevant Data information was given to them.

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the thermodynamic efficiency and environmental impact performance of fossil fuel utilization. General Electric Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Advanced Gasification-Combustion (AGC) concept to produce H{sub 2} and sequestration-ready CO{sub 2} from solid fuels. The AGC module offers potential for reduced cost and increased energy efficiency relative to conventional gasification and combustion systems. GE EER was awarded a Vision-21 program from U.S. DOE NETL tomore » develop the AGC technology. Work on this three-year program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T. R. Miles, Technical Consultants, Inc. In the AGC technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on preliminary modeling work in the first quarter of this program, has an estimated process efficiency of approximately 67% based on electrical and H{sub 2} energy outputs relative to the higher heating value of coal. The three-year R&D program will determine the operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the AGC concept. This is the fifth quarterly technical progress report for the Vision-21 AGC program supported by U.S. DOE NETL (Contract: DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting October 1, 2001 and ending December 31, 2001. The report includes an introduction summarizing the AGC concept, main program tasks, and program objectives; it also provides a summary of program activities covering program management and progress in tasks including lab- and bench-scale experimental testing, pilot-scale design, and economic studies.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the thermodynamic efficiency and environmental impact performance of fossil fuel utilization. General Electric Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Advanced Gasification-Combustion (AGC) concept to produce H{sub 2} and sequestration-ready CO{sub 2} from solid fuels. The AGC module offers potential for reduced cost and increased energy efficiency relative to conventional gasification and combustion systems. GE EER was awarded a Vision-21 program from U.S. DOE NETL tomore » develop the AGC technology. Work on this three-year program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T. R. Miles, Technical Consultants, Inc. In the AGC technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on preliminary modeling work in the first quarter of this program, has an estimated process efficiency of approximately 67% based on electrical and H{sub 2} energy outputs relative to the higher heating value of coal. The three-year R&D program will determine the operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the AGC concept. This is the seventh quarterly technical progress report for the Vision-21 AGC program supported by U.S. DOE NETL (Contract: DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting April 1, 2002 and ending June 30, 2002. The report includes an introduction summarizing the AGC concept, main program tasks, and program objectives; it also provides a summary of program activities covering program management and progress in tasks including lab-/bench-scale experimental testing and pilot-scale design.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the thermodynamic efficiency and environmental impact performance of fossil fuel utilization. GE Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Advanced Gasification-Combustion (AGC) concept to produce H{sub 2} and sequestration-ready CO{sub 2} from solid fuels. The AGC module offers potential for reduced cost and increased energy efficiency relative to conventional gasification and combustion systems. GE EER was awarded a Vision 21 program from U.S. DOE NETL tomore » develop the AGC technology. Work on this three-year program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T. R. Miles, Technical Consultants, Inc. In the AGC technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on preliminary modeling work, has an estimated process efficiency of approximately 67% based on electrical and H{sub 2} energy outputs relative to the higher heating value of coal. The three-year R&D program will determine the operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the AGC concept. This is the second annual technical progress report for the Vision 21 AGC program supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting October 1, 2001 and ending September 30, 2002. The report includes an introduction summarizing the AGC concept, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab- and bench-scale experimental testing, pilot-scale design and assembly, and program management.« less

Industrial Automation Mechanic Model Curriculum Project. Final Report.

ERIC Educational Resources Information Center

Toledo Public Schools, OH.

This document describes a demonstration program that developed secondary level competency-based instructional materials for industrial automation mechanics. Program activities included task list compilation, instructional materials research, learning activity packet (LAP) development, construction of lab elements, system implementation,…

Human Engineering Modeling and Performance Lab Study Project

NASA Technical Reports Server (NTRS)

Oliva-Buisson, Yvette J.

2014-01-01

The HEMAP (Human Engineering Modeling and Performance) Lab is a joint effort between the Industrial and Human Engineering group and the KAVE (Kennedy Advanced Visualiations Environment) group. The lab consists of sixteen camera system that is used to capture human motions and operational tasks, through te use of a Velcro suit equipped with sensors, and then simulate these tasks in an ergonomic software package know as Jac, The Jack software is able to identify the potential risk hazards.

Technical memo : project 0-6132 (task 6).

DOT National Transportation Integrated Search

2010-04-01

The attached memo presents construction information on the test sections placed by Madden Construction on US 59 on March 26th 2010. The memo includes details of the mix design, shows photographs of the construction sequence, lab test data on the Cont...

DeepLab: Semantic Image Segmentation with Deep Convolutional Nets, Atrous Convolution, and Fully Connected CRFs.

PubMed

Chen, Liang-Chieh; Papandreou, George; Kokkinos, Iasonas; Murphy, Kevin; Yuille, Alan L

2018-04-01

In this work we address the task of semantic image segmentation with Deep Learning and make three main contributions that are experimentally shown to have substantial practical merit. First, we highlight convolution with upsampled filters, or 'atrous convolution', as a powerful tool in dense prediction tasks. Atrous convolution allows us to explicitly control the resolution at which feature responses are computed within Deep Convolutional Neural Networks. It also allows us to effectively enlarge the field of view of filters to incorporate larger context without increasing the number of parameters or the amount of computation. Second, we propose atrous spatial pyramid pooling (ASPP) to robustly segment objects at multiple scales. ASPP probes an incoming convolutional feature layer with filters at multiple sampling rates and effective fields-of-views, thus capturing objects as well as image context at multiple scales. Third, we improve the localization of object boundaries by combining methods from DCNNs and probabilistic graphical models. The commonly deployed combination of max-pooling and downsampling in DCNNs achieves invariance but has a toll on localization accuracy. We overcome this by combining the responses at the final DCNN layer with a fully connected Conditional Random Field (CRF), which is shown both qualitatively and quantitatively to improve localization performance. Our proposed "DeepLab" system sets the new state-of-art at the PASCAL VOC-2012 semantic image segmentation task, reaching 79.7 percent mIOU in the test set, and advances the results on three other datasets: PASCAL-Context, PASCAL-Person-Part, and Cityscapes. All of our code is made publicly available online.

Examining and contrasting the cognitive activities engaged in undergraduate research experiences and lab courses

NASA Astrophysics Data System (ADS)

Holmes, N. G.; Wieman, Carl E.

2016-12-01

While the positive outcomes of undergraduate research experiences (UREs) have been extensively categorized, the mechanisms for those outcomes are less understood. Through lightly structured focus group interviews, we have extracted the cognitive tasks that students identify as engaging in during their UREs. We also use their many comparative statements about their coursework, especially lab courses, to evaluate their experimental physics-related cognitive tasks in those environments. We find there are a number of cognitive tasks consistently encountered in physics UREs that are present in most experimental research. These are seldom encountered in lab or lecture courses, with some notable exceptions. Having time to reflect and fix or revise, and having a sense of autonomy, were both repeatedly cited as key enablers of the benefits of UREs. We also identify tasks encountered in actual experimental research that are not encountered in UREs. We use these findings to identify opportunities for better integration of the cognitive tasks in UREs and lab courses, as well as discussing the barriers that exist. This work responds to extensive calls for science education to better develop students' scientific skills and practices, as well as calls to expose more students to scientific research.

RANS Simulation (Rotating Reference Frame Model [RRF]) of Single Lab-Scaled DOE RM1 MHK Turbine

DOE Data Explorer

Javaherchi, Teymour; Stelzenmuller, Nick; Aliseda, Alberto; Seydel, Joseph

2014-04-15

Attached are the .cas and .dat files for the Reynolds Averaged Navier-Stokes (RANS) simulation of a single lab-scaled DOE RM1 turbine implemented in ANSYS FLUENT CFD-package. The lab-scaled DOE RM1 is a re-design geometry, based of the full scale DOE RM1 design, producing same power output as the full scale model, while operating at matched Tip Speed Ratio values at reachable laboratory Reynolds number (see attached paper). In this case study taking advantage of the symmetry of lab-scaled DOE RM1 geometry, only half of the geometry is models using (Single) Rotating Reference Frame model [RRF]. In this model RANS equations, coupled with k-\\omega turbulence closure model, are solved in the rotating reference frame. The actual geometry of the turbine blade is included and the turbulent boundary layer along the blade span is simulated using wall-function approach. The rotation of the blade is modeled by applying periodic boundary condition to sets of plane of symmetry. This case study simulates the performance and flow field in the near and far wake of the device at the desired operating conditions. The results of these simulations were validated against in-house experimental data. Please see the attached paper.

Nano/micro-scale magnetophoretic devices for biomedical applications

NASA Astrophysics Data System (ADS)

Lim, Byeonghwa; Vavassori, Paolo; Sooryakumar, R.; Kim, CheolGi

2017-01-01

In recent years there have been tremendous advances in the versatility of magnetic shuttle technology using nano/micro-scale magnets for digital magnetophoresis. While the technology has been used for a wide variety of single-cell manipulation tasks such as selection, capture, transport, encapsulation, transfection, or lysing of magnetically labeled and unlabeled cells, it has also expanded to include parallel actuation and study of multiple bio-entities. The use of nano/micro-patterned magnetic structures that enable remote control of the applied forces has greatly facilitated integration of the technology with microfluidics, thereby fostering applications in the biomedical arena. The basic design and fabrication of various scaled magnets for remote manipulation of individual and multiple beads/cells, and their associated energies and forces that underlie the broad functionalities of this approach, are presented. One of the most useful features enabled by such advanced integrated engineering is the capacity to remotely tune the magnetic field gradient and energy landscape, permitting such multipurpose shuttles to be implemented within lab-on-chip platforms for a wide range of applications at the intersection of cellular biology and biotechnology.

Naval Medical Research and Development News. Volume 7, Issue 9

DTIC Science & Technology

2015-09-01

satisfaction with the simulated training; career intentions; and, general, occupational, and task-specific self-efficacy using pretest and post - test ...samples needed to be transported to the labs for testing . What was needed was a rapid, on -site, diagnostic test that could be done quickly. "The U.S...relatively small size of the group -- usually only a handful of people per deployment - required members to juggle multiple tasks on their own, including

On the status of IAEA delta-13C stable isotope reference materials.

NASA Astrophysics Data System (ADS)

Assonov, Sergey; Groening, Manfred; Fajgelj, Ales

2016-04-01

For practical reasons all isotope measurements are performed on relative scales realized through the use of international, scale-defining primary standards. In fact these standards were materials (artefacts, similar to prototypes of meter and kg) selected based on their properties. The VPDB delta-13C scale is realised via two highest-level reference materials NBS19 and LSVEC, the first defining the scale and the second aimed to normalise lab-to-lab calibrations. These two reference materials (RMs) have been maintained and distributed by IAEA and NIST. The priority task is to maintain these primary RMs at the required uncertainty level, thus ensuring the long-term scale consistency. The second task is to introduce replacements when needed (currently for exhausted NBS19, work in progress). The next is to produce a family of lower level RMs (secondary, tertiary) addressing needs of various applications (with different delta values, in different physical-chemical forms) and their needs for the uncertainty; these RMs should be traceable to the highest level RMs. Presently three is a need for a range of RMs addressing existing and newly emerging analytical techniques (e.g. optical isotopic analysers) in form of calibrated CO2 gases with different delta-13C values. All that implies creating a family of delta-13C stable isotope reference materials. Presently IAEA works on replacement for NBS19 and planning new RMs. Besides, we found that LSVEC (introduced as second anchor for the VPDB scale in 2006) demonstrate a considerable scatter of its delta-13C value which implies a potential bias of the property value and increased value uncertainty which may conflict with uncertainty requirements for atmospheric monitoring. That is not compatible with the status of LSVEC, and therefore it should be replaced as soon as possible. The presentation will give an overview of the current status, the strategic plan of developments and the near future steps.

Characterizing attention with predictive network models

PubMed Central

Rosenberg, M. D.; Finn, E. S.; Scheinost, D.; Constable, R. T.; Chun, M. M.

2017-01-01

Recent work shows that models based on functional connectivity in large-scale brain networks can predict individuals’ attentional abilities. Some of the first generalizable neuromarkers of cognitive function, these models also inform our basic understanding of attention, providing empirical evidence that (1) attention is a network property of brain computation, (2) the functional architecture that underlies attention can be measured while people are not engaged in any explicit task, and (3) this architecture supports a general attentional ability common to several lab-based tasks and impaired in attention deficit hyperactivity disorder. Looking ahead, connectivity-based predictive models of attention and other cognitive abilities and behaviors may potentially improve the assessment, diagnosis, and treatment of clinical dysfunction. PMID:28238605

Spaceport Processing System Development Lab

NASA Technical Reports Server (NTRS)

Dorsey, Michael

2013-01-01

The Spaceport Processing System Development Lab (SPSDL), developed and maintained by the Systems Hardware and Engineering Branch (NE-C4), is a development lab with its own private/restricted networks. A private/restricted network is a network with restricted or no communication with other networks. This allows users from different groups to work on their own projects in their own configured environment without interfering with others utilizing their resources in the lab. The different networks being used in the lab have no way to talk with each other due to the way they are configured, so how a user configures his software, operating system, or the equipment doesn't interfere or carry over on any of the other networks in the lab. The SPSDL is available for any project in KSC that is in need of a lab environment. My job in the SPSDL was to assist in maintaining the lab to make sure it's accessible for users. This includes, but is not limited to, making sure the computers in the lab are properly running and patched with updated hardware/software. In addition to this, I also was to assist users who had issues in utilizing the resources in the lab, which may include helping to configure a restricted network for their own environment. All of this was to ensure workers were able to use the SPSDL to work on their projects without difficulty which would in turn, benefit the work done throughout KSC. When I wasn't working in the SPSDL, I would instead help other coworkers with smaller tasks which included, but wasn't limited to, the proper disposal, moving of, or search for essential equipment. I also, during the free time I had, used NASA's resources to increase my knowledge and skills in a variety of subjects related to my major as a computer engineer, particularly in UNIX, Networking, and Embedded Systems.

RANS Simulation (Virtual Blade Model [VBM]) of Single Lab Scaled DOE RM1 MHK Turbine

DOE Data Explorer

Javaherchi, Teymour; Stelzenmuller, Nick; Aliseda, Alberto; Seydel, Joseph

2014-04-15

Attached are the .cas and .dat files for the Reynolds Averaged Navier-Stokes (RANS) simulation of a single lab-scaled DOE RM1 turbine implemented in ANSYS FLUENT CFD-package. The lab-scaled DOE RM1 is a re-design geometry, based of the full scale DOE RM1 design, producing same power output as the full scale model, while operating at matched Tip Speed Ratio values at reachable laboratory Reynolds number (see attached paper). In this case study the flow field around and in the wake of the lab-scaled DOE RM1 turbine is simulated using Blade Element Model (a.k.a Virtual Blade Model) by solving RANS equations coupled with k-\\omega turbulence closure model. It should be highlighted that in this simulation the actual geometry of the rotor blade is not modeled. The effect of turbine rotating blades are modeled using the Blade Element Theory. This simulation provides an accurate estimate for the performance of device and structure of it's turbulent far wake. Due to the simplifications implemented for modeling the rotating blades in this model, VBM is limited to capture details of the flow field in near wake region of the device. The required User Defined Functions (UDFs) and look-up table of lift and drag coefficients are included along with the .cas and .dat files.

Human Factors Virtual Analysis Techniques for NASA's Space Launch System Ground Support using MSFC's Virtual Environments Lab (VEL)

NASA Technical Reports Server (NTRS)

Searcy, Brittani

2017-01-01

Using virtual environments to assess complex large scale human tasks provides timely and cost effective results to evaluate designs and to reduce operational risks during assembly and integration of the Space Launch System (SLS). NASA's Marshall Space Flight Center (MSFC) uses a suite of tools to conduct integrated virtual analysis during the design phase of the SLS Program. Siemens Jack is a simulation tool that allows engineers to analyze human interaction with CAD designs by placing a digital human model into the environment to test different scenarios and assess the design's compliance to human factors requirements. Engineers at MSFC are using Jack in conjunction with motion capture and virtual reality systems in MSFC's Virtual Environments Lab (VEL). The VEL provides additional capability beyond standalone Jack to record and analyze a person performing a planned task to assemble the SLS at Kennedy Space Center (KSC). The VEL integrates Vicon Blade motion capture system, Siemens Jack, Oculus Rift, and other virtual tools to perform human factors assessments. By using motion capture and virtual reality, a more accurate breakdown and understanding of how an operator will perform a task can be gained. By virtual analysis, engineers are able to determine if a specific task is capable of being safely performed by both a 5% (approx. 5ft) female and a 95% (approx. 6'1) male. In addition, the analysis will help identify any tools or other accommodations that may to help complete the task. These assessments are critical for the safety of ground support engineers and keeping launch operations on schedule. Motion capture allows engineers to save and examine human movements on a frame by frame basis, while virtual reality gives the actor (person performing a task in the VEL) an immersive view of the task environment. This presentation will discuss the need of human factors for SLS and the benefits of analyzing tasks in NASA MSFC's VEL.

The Importance of Team Sex Composition in Team-Training Research Employing Complex Psychomotor Tasks.

PubMed

Jarrett, Steven M; Glaze, Ryan M; Schurig, Ira; Arthur, Winfred

2017-08-01

The relationship between team sex composition and team performance on a complex psychomotor task was examined because these types of tasks are commonly used in the lab-based teams literature. Despite well-documented sex-based differences on complex psychomotor tasks, the preponderance of studies-mainly lab based-that use these tasks makes no mention of the sex composition of teams across or within experimental conditions. A sample of 123 four-person teams with varying team sex composition learned and performed a complex psychomotor task, Steal Beasts Pro PE. Each team completed a 5-hr protocol whereby they conducted several performance missions. The results indicated significant large mean differences such that teams with larger proportions of males had higher performance scores. These findings demonstrate the potential effect of team sex composition on the validity of studies that use complex psychomotor tasks to explore and investigate team performance-related phenomena when (a) team sex composition is not a focal variable of interest and (b) it is not accounted for or controlled. Given the proclivity of complex psychomotor action-based tasks used in lab-based team studies, it is important to understand and control for the impact of team sex composition on team performance. When team sex composition is not controlled for, either methodologically or statistically, it may affect the validity of the results in teams studies using these types of tasks.

Small-scale spatial cognition in pigeons.

PubMed

Cheng, Ken; Spetch, Marcia L; Kelly, Debbie M; Bingman, Verner P

2006-05-01

Roberts and Van Veldhuizen's [Roberts, W.A., Van Veldhuizen, N., 1985. Spatial memory in pigeons on the radial maze. J. Exp. Psychol.: Anim. Behav. Proc. 11, 241-260] study on pigeons in the radial maze sparked research on landmark use by pigeons in lab-based tasks as well as variants of the radial-maze task. Pigeons perform well on open-field versions of the radial maze, with feeders scattered on the laboratory floor. Pigeons can also be trained to search precisely for buried food. The search can be based on multiple landmarks, but is sometimes controlled by just one or two landmarks, with the preferred landmarks varying across individuals. Findings are similar in landmark-based searching on a computer monitor and on a lab floor, despite many differences between the two kinds of tasks. A number of general learning principles are found in landmark-based searching, such as cue competition, generalization and peak shift, and selective attention. Pigeons also learn the geometry of the environment in which they are searching. Neurophysiological studies have implicated the hippocampal formation (HF) in avian spatial cognition, with the right hippocampus hypothesized to play a more important role in the spatial recognition of goal locations. Most recently, single-cell recording from the pigeon's hippocampal formation has revealed cells with different properties from the classic 'place' cells of rats, as well as differences in the two sides of the hippocampus.

Developing automated analytical methods for scientific environments using LabVIEW.

PubMed

Wagner, Christoph; Armenta, Sergio; Lendl, Bernhard

2010-01-15

The development of new analytical techniques often requires the building of specially designed devices, each requiring its own dedicated control software. Especially in the research and development phase, LabVIEW has proven to be one highly useful tool for developing this software. Yet, it is still common practice to develop individual solutions for different instruments. In contrast to this, we present here a single LabVIEW-based program that can be directly applied to various analytical tasks without having to change the program code. Driven by a set of simple script commands, it can control a whole range of instruments, from valves and pumps to full-scale spectrometers. Fluid sample (pre-)treatment and separation procedures can thus be flexibly coupled to a wide range of analytical detection methods. Here, the capabilities of the program have been demonstrated by using it for the control of both a sequential injection analysis - capillary electrophoresis (SIA-CE) system with UV detection, and an analytical setup for studying the inhibition of enzymatic reactions using a SIA system with FTIR detection.

Computer Aided Battery Engineering Consortium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pesaran, Ahmad

A multi-national lab collaborative team was assembled that includes experts from academia and industry to enhance recently developed Computer-Aided Battery Engineering for Electric Drive Vehicles (CAEBAT)-II battery crush modeling tools and to develop microstructure models for electrode design - both computationally efficient. Task 1. The new Multi-Scale Multi-Domain model framework (GH-MSMD) provides 100x to 1,000x computation speed-up in battery electrochemical/thermal simulation while retaining modularity of particles and electrode-, cell-, and pack-level domains. The increased speed enables direct use of the full model in parameter identification. Task 2. Mechanical-electrochemical-thermal (MECT) models for mechanical abuse simulation were simultaneously coupled, enabling simultaneous modelingmore » of electrochemical reactions during the short circuit, when necessary. The interactions between mechanical failure and battery cell performance were studied, and the flexibility of the model for various batteries structures and loading conditions was improved. Model validation is ongoing to compare with test data from Sandia National Laboratories. The ABDT tool was established in ANSYS. Task 3. Microstructural modeling was conducted to enhance next-generation electrode designs. This 3- year project will validate models for a variety of electrodes, complementing Advanced Battery Research programs. Prototype tools have been developed for electrochemical simulation and geometric reconstruction.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the thermodynamic efficiency and environmental impact performance of fossil fuel utilization. General Electric Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Advanced Gasification-Combustion (AGC) concept to produce H{sub 2} and sequestration-ready CO{sub 2} from solid fuels. The AGC module offers potential for reduced cost and increased energy efficiency relative to conventional gasification and combustion systems. GE EER was awarded a Vision-21 program from U.S. DOE NETL tomore » develop the AGC technology. Work on this three-year program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T. R. Miles, Technical Consultants, Inc. In the AGC technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on preliminary modeling work in the first quarter of this program, has an estimated process efficiency of approximately 67% based on electrical and H{sub 2} energy outputs relative to the higher heating value of coal. The three-year R&D program will determine the operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the AGC concept. This is the third quarterly technical progress report for the Vision-21 AGC program supported by U.S. DOE NETL (Contract: DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting April 1, 2001 and ending June 30, 2001. The report includes an introduction summarizing the AGC concept, main program tasks, objectives of this program, and provides a summary of program activities covering program management and progress in first year tasks including lab- and bench-scale design, facilities preparation, and engineering studies.« less

LabVIEW Task Manager v. 1.10.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vargo, Timothy D.

LabVIEW Task Manager is a debugging tool for use during code development in the National Instruments (NI) LabVIEW® IDE. While providing a dynamic & big-picture view of running code, an expandable/collapsible tree diagram displays detailed information (both static and dynamic) on all VIs in memory, belonging to a selected project/target. It allows for interacting with single or multiple selected VIs at a time, providing significant benefits while troubleshooting, and has the following features: Look & Feel similar to Windows® Task Manager; Selection of project/target; Lists all VIs in memory, grouped by class/library; Searches for and enumerates clones in memory; DropInmore » VI for including dynamically referenced clones (Clone Beacon); 'Refresh Now' (F5) re-reads all VIs in memory and adds new ones to the tree; Displays VI name, owning class/library, state, path, data size & code size; Displays VI FP Behavior, Reentrant?, Reentrancy Type, Paused? & Highlight?; Sort by any column, including by library name; Filter by item types vi, ctl, and vit/ctt; Filter out vi.lib and global VIs; Tracking of, and ability to toggle, execution highlighting on multiple selected VIs; Tracking of paused VIs with ability to Pause/Resume/TogglePause multiple selected VIs; DropIn VI for pausing on a condition; If a clone initiates a pause, a different pause symbol is used for all clones of that same reentrant original VI; Select multiple VIs and open or close their FPs or BDs; Double Click a VI from the tree to bring the BD (first choice) or FP to front, if already open; and Select multiple top-level VIs and Abort them.« less

Improving the Quality of Lab Reports by Using Them as Lab Instructions

NASA Astrophysics Data System (ADS)

Haagen-Schuetzenhoefer, Claudia

2012-10-01

Lab exercises are quite popular in teaching science. Teachers have numerous goals in mind when teaching science laboratories. Nevertheless, empirical research draws a heterogeneous picture of the benefits of lab work. Research has shown that it does not necessarily contribute to the enhancement of practical abilities or content knowledge. Lab activities are frequently based on recipe-like, step-by-step instructions ("cookbook style"), which do not motivate students to engage cognitively. Consequently, students put the emphasis on "task completion" or "manipulating equipment."2

Model-Based Extracted Water Desalination System for Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dees, Elizabeth M.; Moore, David Roger; Li, Li

Over the last 1.5 years, GE Global Research and Pennsylvania State University defined a model-based, scalable, and multi-stage extracted water desalination system that yields clean water, concentrated brine, and, optionally, salt. The team explored saline brines that ranged across the expected range for extracted water for carbon sequestration reservoirs (40,000 up to 220,000 ppm total dissolved solids, TDS). In addition, the validated the system performance at pilot scale with field-sourced water using GE’s pre-pilot and lab facilities. This project encompassed four principal tasks, in addition to Project Management and Planning: 1) identify a deep saline formation carbon sequestration site andmore » a partner that are suitable for supplying extracted water; 2) conduct a techno-economic assessment and down-selection of pre-treatment and desalination technologies to identify a cost-effective system for extracted water recovery; 3) validate the downselected processes at the lab/pre-pilot scale; and 4) define the scope of the pilot desalination project. Highlights from each task are described below: Deep saline formation characterization The deep saline formations associated with the five DOE NETL 1260 Phase 1 projects were characterized with respect to their mineralogy and formation water composition. Sources of high TDS feed water other than extracted water were explored for high TDS desalination applications, including unconventional oil and gas and seawater reverse osmosis concentrate. Technoeconomic analysis of desalination technologies Techno-economic evaluations of alternate brine concentration technologies, including humidification-dehumidification (HDH), membrane distillation (MD), forward osmosis (FO), turboexpander-freeze, solvent extraction and high pressure reverse osmosis (HPRO), were conducted. These technologies were evaluated against conventional falling film-mechanical vapor recompression (FF-MVR) as a baseline desalination process. Furthermore, a quality function deployment (QFD) method was used to compare alternate high TDS desalination technologies to FF-MVR. High pressure reverse osmosis was found to a be a promising alternative desalination technology. A deep-dive technoeconomic analysis of HPRO was performed, including Capex and Opex estimates, for seawater RO (SWRO). Additionally, two additional cases were explored: 1) a comparison of a SWRO plus HPRO system to the option of doubling the size of a standard seawater RO system to achieve the same total pure water recovery rate; and 2) a flue gas desulfurization wastewater treatment zero-liquid discharge (ZLD) application, where preconcentration with RO (SWRO or SWRO + HPRO) before evaporation and crystallization was compared to FF-MVR and crystallization technologies without RO preconcentration. Pre-pilot process validation Pre-pilot-scale tests were conducted using field production water to validate key process steps for extracted water pretreatment. Approximately 5,000 gallons of field produced water was processed through, microfiltration, ultrafiltration, and steam regenerable sorbent operations. Smaller quantities were processed through microclarification. In addition, analytical methods (purge-and-trap gas chromatography and Hach TOC analytical methods) were validated. Lab-scale HPRO elements were constructed and tested at high pressures, to identify and mitigate technical risks of the technology. Lastly, improvements in RO membrane materials were identified as the necessary next step to achieve further improvement in element performance at high pressure. Scope of Field Pilot A field pilot for extracted water pretreatment was designed.« less

Modifying your Physics and Astronomy Courses to Incorporate Heliophysics - Some Examples

NASA Astrophysics Data System (ADS)

Cebulka, Rebecca; Cox, Amanda; Rodriguez Garrigues, Alvar; Hoshino, Laura; Fitzgerald, Cullen; Montgomery, M.; Al-Rawi, Ahlam N.; Velissaris, Christos; Flitsiyan, Elena

2016-01-01

Although physics and astronomy courses include heliophysics topics, students still leave the courses without knowing what heliophysics is and how heliophysics relates to their daily lives. To meet goals of NASA's Living With a Star Program, UCF Physics has modified courses such as SCALE-UP: Electricity and Magnetism for Engineers and Scientists, Astronomy (for non-science majors), and Astrophysics to include heliophysics topics. In this poster, we present the previous labs, the student-modified labs to incorporate heliophysics, and we present student learning statistics.

Better dual-task processing in simultaneous interpreters

PubMed Central

Strobach, Tilo; Becker, Maxi; Schubert, Torsten; Kühn, Simone

2015-01-01

Simultaneous interpreting (SI) is a highly complex activity and requires the performance and coordination of multiple, simultaneous tasks: analysis and understanding of the discourse in a first language, reformulating linguistic material, storing of intermediate processing steps, and language production in a second language among others. It is, however, an open issue whether persons with experience in SI possess superior skills in coordination of multiple tasks and whether they are able to transfer these skills to lab-based dual-task situations. Within the present study, we set out to explore whether interpreting experience is associated with related higher-order executive functioning in the context of dual-task situations of the Psychological Refractory Period (PRP) type. In this PRP situation, we found faster reactions times in participants with experience in simultaneous interpretation in contrast to control participants without such experience. Thus, simultaneous interpreters possess superior skills in coordination of multiple tasks in lab-based dual-task situations. PMID:26528232

3D-Lab: a collaborative web-based platform for molecular modeling.

PubMed

Grebner, Christoph; Norrby, Magnus; Enström, Jonatan; Nilsson, Ingemar; Hogner, Anders; Henriksson, Jonas; Westin, Johan; Faramarzi, Farzad; Werner, Philip; Boström, Jonas

2016-09-01

The use of 3D information has shown impact in numerous applications in drug design. However, it is often under-utilized and traditionally limited to specialists. We want to change that, and present an approach making 3D information and molecular modeling accessible and easy-to-use 'for the people'. A user-friendly and collaborative web-based platform (3D-Lab) for 3D modeling, including a blazingly fast virtual screening capability, was developed. 3D-Lab provides an interface to automatic molecular modeling, like conformer generation, ligand alignments, molecular dockings and simple quantum chemistry protocols. 3D-Lab is designed to be modular, and to facilitate sharing of 3D-information to promote interactions between drug designers. Recent enhancements to our open-source virtual reality tool Molecular Rift are described. The integrated drug-design platform allows drug designers to instantaneously access 3D information and readily apply advanced and automated 3D molecular modeling tasks, with the aim to improve decision-making in drug design projects.

Investigation of the role of flocculation conditions in recuperative thickening on dewatering performance and biogas production.

PubMed

Cobbledick, Jeffrey; Zhang, Victor; Rollings-Scattergood, Sasha; Latulippe, David R

2017-11-01

There is considerable interest in recuperative thickening (RT), the recycling of partially digested solids in an anaerobic digester outlet stream back into the incoming feed, as a 'high-performance' process to increase biogas production, increase system capacity, and improve biosolids stabilization. While polymer flocculation is commonly used in full-scale RT operations, no studies have investigated the effect of flocculation conditions on RT process performance. Our goal was to investigate the effect of polymer type and dosage conditions on dewatering performance and biogas production in a lab-scale RT system. The type of polymer flocculant significantly affected dewatering performance. For example, the 440 LH polymer (low molecular weight (MW) polyacrylamide) demonstrated lower capillary suction time (CST) and filtrate total suspended solids (TSS) values than the C-6267 polymer (high MW polyacrylamide). An examination of the dewatering performance of RT digesters with different polymers found a strong correlation between CST and filtrate TSS. The type of polymer flocculant had no significant effect on biogas productivity or composition; the methane content was greater than 60% in good agreement with typical results. The optimization of the polymer flocculation conditions is a critical task for which the lab-scale RT system used in this work is ideally suited.

Virus removal retention challenge tests performed at lab scale and pilot scale during operation of membrane units.

PubMed

Humbert, H; Machinal, C; Labaye, Ivan; Schrotter, J C

2011-01-01

The determination of the virus retention capabilities of UF units during operation is essential for the operators of drinking water treatment facilities in order to guarantee an efficient and stable removal of viruses through time. In previous studies, an effective method (MS2-phage challenge tests) was developed by the Water Research Center of Veolia Environnement for the measurement of the virus retention rates (Log Removal Rate, LRV) of commercially available hollow fiber membranes at lab scale. In the present work, the protocol for monitoring membrane performance was transferred from lab scale to pilot scale. Membrane performances were evaluated during pilot trial and compared to the results obtained at lab scale with fibers taken from the pilot plant modules. PFU culture method was compared to RT-PCR method for the calculation of LRV in both cases. Preliminary tests at lab scale showed that both methods can be used interchangeably. For tests conducted on virgin membrane, a good consistency was observed between lab and pilot scale results with the two analytical methods used. This work intends to show that a reliable determination of the membranes performances based on RT-PCR analytical method can be achieved during the operation of the UF units.

Fabrication of coronagraph masks and laboratory scale star-shade masks: characteristics, defects, and performance

NASA Astrophysics Data System (ADS)

Balasubramanian, Kunjithapatham; Riggs, A. J. Eldorado; Cady, Eric; White, Victor; Yee, Karl; Wilson, Daniel; Echternach, Pierre; Muller, Richard; Mejia Prada, Camilo; Seo, Byoung-Joon; Shi, Fang; Ryan, Daniel; Fregoso, Santos; Metzman, Jacob; Wilson, Robert Casey

2017-09-01

NASA WFIRST mission has planned to include a coronagraph instrument to find and characterize exoplanets. Masks are needed to suppress the host star light to better than 10-8 - 10-9 level contrast over a broad bandwidth to enable the coronagraph mission objectives. Such masks for high contrast coronagraphic imaging require various fabrication technologies to meet a wide range of specifications, including precise shapes, micron scale island features, ultra-low reflectivity regions, uniformity, wave front quality, etc. We present the technologies employed at JPL to produce these pupil plane and image plane coronagraph masks, and lab-scale external occulter masks, highlighting accomplishments from the high contrast imaging testbed (HCIT) at JPL and from the high contrast imaging lab (HCIL) at Princeton University. Inherent systematic and random errors in fabrication and their impact on coronagraph performance are discussed with model predictions and measurements.

Here's the beef: A case study in organizational transformation

NASA Technical Reports Server (NTRS)

Huseonica, William F.; Giardino, Marco J.

1992-01-01

The Science and Technology Lab (STL) is tasked with the design, development, and application of the science and engineering services. Formed in the early 1970's STL adhered to many traditional attitudes including barriers to communication, excessive management control, parochial strategies, unclear measures of success, lack of customer focus, underutilization of people, and excessive administrative burdens on scientists and engineers. The challenge for the STL was to maximize customer satisfaction through the effective and efficient application of the notable skills and talents of the STL's workforce. In this way, the Lab would begin its exciting journey toward becoming world class. A discussion of this on-going transformation is presented.

Particulate and Gaseous Emissions Measurement System (PAGEMS) Project

NASA Technical Reports Server (NTRS)

Kostic, Milivoje

2003-01-01

Professor Kostic will work on the current UEET program of the Aerosol and Particulate task. This task will focus on: how to acquire experimental data through Labview software how to make the data acquisition system more efficient trouble existing problem of the labview software recommend a better system improve existing system with better data and usually friendly.Three different assignments in this project included:Particle-Size Distribution Data Presentation;Error or Uncertainty Analysis of Measurement Results; and Enhancement of LabVlRN Data Acquisition Program for GRC PAGEMS Project.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Springmeyer, R R; Brugger, E; Cook, R

The Data group provides data analysis and visualization support to its customers. This consists primarily of the development and support of VisIt, a data analysis and visualization tool. Support ranges from answering questions about the tool, providing classes on how to use the tool, and performing data analysis and visualization for customers. The Information Management and Graphics Group supports and develops tools that enhance our ability to access, display, and understand large, complex data sets. Activities include applying visualization software for large scale data exploration; running video production labs on two networks; supporting graphics libraries and tools for end users;more » maintaining PowerWalls and assorted other displays; and developing software for searching and managing scientific data. Researchers in the Center for Applied Scientific Computing (CASC) work on various projects including the development of visualization techniques for large scale data exploration that are funded by the ASC program, among others. The researchers also have LDRD projects and collaborations with other lab researchers, academia, and industry. The IMG group is located in the Terascale Simulation Facility, home to Dawn, Atlas, BGL, and others, which includes both classified and unclassified visualization theaters, a visualization computer floor and deployment workshop, and video production labs. We continued to provide the traditional graphics group consulting and video production support. We maintained five PowerWalls and many other displays. We deployed a 576-node Opteron/IB cluster with 72 TB of memory providing a visualization production server on our classified network. We continue to support a 128-node Opteron/IB cluster providing a visualization production server for our unclassified systems and an older 256-node Opteron/IB cluster for the classified systems, as well as several smaller clusters to drive the PowerWalls. The visualization production systems includes NFS servers to provide dedicated storage for data analysis and visualization. The ASC projects have delivered new versions of visualization and scientific data management tools to end users and continue to refine them. VisIt had 4 releases during the past year, ending with VisIt 2.0. We released version 2.4 of Hopper, a Java application for managing and transferring files. This release included a graphical disk usage view which works on all types of connections and an aggregated copy feature for quickly transferring massive datasets quickly and efficiently to HPSS. We continue to use and develop Blockbuster and Telepath. Both the VisIt and IMG teams were engaged in a variety of movie production efforts during the past year in addition to the development tasks.« less

Online webcam-based eye tracking in cognitive science: A first look.

PubMed

Semmelmann, Kilian; Weigelt, Sarah

2018-04-01

Online experimentation is emerging in many areas of cognitive psychology as a viable alternative or supplement to classical in-lab experimentation. While performance- and reaction-time-based paradigms are covered in recent studies, one instrument of cognitive psychology has not received much attention up to now: eye tracking. In this study, we used JavaScript-based eye tracking algorithms recently made available by Papoutsaki et al. (International Joint Conference on Artificial Intelligence, 2016) together with consumer-grade webcams to investigate the potential of online eye tracking to benefit from the common advantages of online data conduction. We compared three in-lab conducted tasks (fixation, pursuit, and free viewing) with online-acquired data to analyze the spatial precision in the first two, and replicability of well-known gazing patterns in the third task. Our results indicate that in-lab data exhibit an offset of about 172 px (15% of screen size, 3.94° visual angle) in the fixation task, while online data is slightly less accurate (18% of screen size, 207 px), and shows higher variance. The same results were found for the pursuit task with a constant offset during the stimulus movement (211 px in-lab, 216 px online). In the free-viewing task, we were able to replicate the high attention attribution to eyes (28.25%) compared to other key regions like the nose (9.71%) and mouth (4.00%). Overall, we found web technology-based eye tracking to be suitable for all three tasks and are confident that the required hard- and software will be improved continuously for even more sophisticated experimental paradigms in all of cognitive psychology.

Biological classification with RNA-Seq data: Can alternatively spliced transcript expression enhance machine learning classifier?

PubMed

Johnson, Nathan T; Dhroso, Andi; Hughes, Katelyn J; Korkin, Dmitry

2018-06-25

The extent to which the genes are expressed in the cell can be simplistically defined as a function of one or more factors of the environment, lifestyle, and genetics. RNA sequencing (RNA-Seq) is becoming a prevalent approach to quantify gene expression, and is expected to gain better insights to a number of biological and biomedical questions, compared to the DNA microarrays. Most importantly, RNA-Seq allows to quantify expression at the gene and alternative splicing isoform levels. However, leveraging the RNA-Seq data requires development of new data mining and analytics methods. Supervised machine learning methods are commonly used approaches for biological data analysis, and have recently gained attention for their applications to the RNA-Seq data. In this work, we assess the utility of supervised learning methods trained on RNA-Seq data for a diverse range of biological classification tasks. We hypothesize that the isoform-level expression data is more informative for biological classification tasks than the gene-level expression data. Our large-scale assessment is done through utilizing multiple datasets, organisms, lab groups, and RNA-Seq analysis pipelines. Overall, we performed and assessed 61 biological classification problems that leverage three independent RNA-Seq datasets and include over 2,000 samples that come from multiple organisms, lab groups, and RNA-Seq analyses. These 61 problems include predictions of the tissue type, sex, or age of the sample, healthy or cancerous phenotypes and, the pathological tumor stage for the samples from the cancerous tissue. For each classification problem, the performance of three normalization techniques and six machine learning classifiers was explored. We find that for every single classification problem, the isoform-based classifiers outperform or are comparable with gene expression based methods. The top-performing supervised learning techniques reached a near perfect classification accuracy, demonstrating the utility of supervised learning for RNA-Seq based data analysis. Published by Cold Spring Harbor Laboratory Press for the RNA Society.

New Policy Focuses on Lab Coats, Safety Glasses, and Footwear | Poster

Cancer.gov

By Paul Stokely, Guest Writer When working in any laboratory or animal facility, you must wear a lab coat, protective eyewear, appropriate gloves, and closed-toe shoes, unless you are performing purely administrative tasks.

Assessing the changes in E. coli levels and nutrient dynamics during vermicomposting of food waste under lab and field scale conditions.

PubMed

Cao, Wenlong; Vaddella, Venkata; Biswas, Sagor; Perkins, Katherine; Clay, Cameron; Wu, Tong; Zheng, Yawen; Ndegwa, Pius; Pandey, Pramod

2016-11-01

Vermicomposting (VC) has proven to be a promising method for treating garden, household, and municipal wastes. Although the VC has been used extensively for converting wastes into fertilizers, pathogens such as Escherichia coli (E. coli) survival during this process is not well documented. In this study, both lab and field scale experiments were conducted assessing the impacts of earthworms in reducing E. coli concentration during VC of food waste. In addition, other pertinent parameters such as temperature, carbon and nitrogen content, moisture content, pH, volatile solids, micronutrients (P, K, Ca, Mg, and S), and heavy metals (Zn, Mn, Fe, and Cu) were monitored during the study. The lab and field scale experiments were conducted for 107 and 103 days, respectively. The carbon to nitrogen ratio (C/N) decreased by 54 % in the lab scale study and by 36 % in the field study. Results showed that VC was not significantly effective in reducing E. coli levels in food waste under both lab and field scale settings. The carbon to nitrogen ratio (C/N) decreased by 54 % in the lab scale study and by 36 % in the field study.

Student Off-Task Electronic Multitasking Predictors: Scale Development and Validation

ERIC Educational Resources Information Center

Qian, Yuxia; Li, Li

2017-01-01

In an attempt to better understand factors contributing to students' off-task electronic multitasking behavior in class, the research included two studies that developed a scale of students' off-task electronic multitasking predictors (the SOTEMP scale), and explored relationships between the scale and various classroom communication processes and…

DOE EiR at Oakridge National Lab 2008/09

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Michael

2012-11-30

This project placed an experienced technology entrepreneur at Oak Ridge National Lab, one of DOE's premier laboratories undertaking cutting edge research in a variety of fields, including energy technologies. With the goal of accelerating the commercialization of advanced energy technologies, the task was to review available technologies at the lab and identify those that qualify for licensing and commercialization by a private startup company, backed by private venture capital. During the project, more than 1,500 inventions filed at the lab were reviewed over a 1 year period; a successively smaller number was selected for more detailed review, ultimately resulting inmore » five, and then 1 technology, being reviewed for immediate commercialization. The chosen technology, consisting in computational chemistry based approached to optimization of enzymes, was tested in lab experiments, paid for by funds raised by ORNL for the purpose of proving out the effectiveness of the technology and readiness for commercialization. The experiments proved out that the technology worked however it's performance proved not yet mature enough to qualify for private venture capital funded commercialization in a high tech startup. As a consequence, the project did not result in a new startup company being formed, as originally intended.« less

Reviews Equipment: LabQuest 2 Equipment: Rubens' Tube Equipment: Ripple Strobe Tank Book: God and the Atom Book: Magnificent Principia, Exploring Isaac Newton's Masterpiece Book: Talking Science: Language, Learning, and Values Classroom Video: Maxwell's Equations Book: Exploring Quantum Physics Through Hands-on Projects Web Watch

NASA Astrophysics Data System (ADS)

2013-11-01

WE RECOMMEND LabQuest 2 New logger now includes mobile data sharing Rubens' Tube Sturdy Rubens' tube ramps up the beat Ripple Strobe Tank Portable ripple tank makes waves in and out of the lab God and the Atom Expertly told story of the influence of atomism Maxwell's Equations Video stands the test of time Exploring Quantum Physics Through Hands-on Projects Mixture of theory and experiment hits the spot WORTH A LOOK Magnificent Principia, Exploring Isaac Newton's Masterpiece The tricky task of summarizing Newton's iconic work Talking Science: Language, Learning, and Values Interesting book tackles communication in the classroom WEB WATCH Interactive website plans a trip to Mars ... documentary peers into telescopes ... films consider the density of water

Evaluation of quartz melt rate furnace with the nitric-glycolic flowsheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, M. S.; Miller, D. H.

The Savannah River National Laboratory (SRNL) was tasked to support validation of the Defense Waste Processing Facility (DWPF) melter offgas flammability model for the Nitric-Glycolic (NG) flowsheet. The work is supplemental to the Cold Cap Evaluation Furnace (CEF) testing conducted in 20141 and the Slurry-fed Melt Rate Furnace (SMRF) testing conducted in 20162 that supported Deliverable 4 of the DWPF & Saltstone Facility Engineering Technical Task Request (TTR).3 The Quartz Melt Rate Furnace (QMRF) was evaluated as a bench-scale scoping tool to potentially be used in lieu of or simply prior to the use of the larger-scale SMRF or CEF.more » The QMRF platform has been used previously to evaluate melt rate behavior and offgas compositions of DWPF glasses prepared from the Nitric-Formic (NF) flowsheet but not for the NG flowsheet and not with continuous feeding.4 The overall objective of the 2016-2017 testing was to evaluate the efficacy of the QMRF as a lab-scale platform for steady state, continuously fed melter testing with the NG flowsheet as an alternative to more expensive and complex testing with the SMRF or CEF platforms.« less

Team Science: Organizing Classroom Experiments That Develop Group Skills.

ERIC Educational Resources Information Center

Coffin, Marilyn

This book contains classroom experiments designed to promote group skills. Each lesson has 4 parts: a 3-minute set-up; 5-minute warm-up, 25-minute experiment, and 5-minute clean-up. During each part, each member of the group is responsible for performing a specific task. Included are 34 labs that cover a range of topics: observations, physical…

[Establishment of Quality Control System of Nucleic Acid Detection for Ebola Virus in Sierra Leone-China Friendship Biological Safety Laboratory].

PubMed

Wang, Qin; Zhang, Yong; Nie, Kai; Wang, Huanyu; Du, Haijun; Song, Jingdong; Xiao, Kang; Lei, Wenwen; Guo, Jianqiang; Wei, Hejiang; Cai, Kun; Wang, Yanhai; Wu, Jiang; Gerald, Bangura; Kamara, Idrissa Laybohr; Liang, Mifang; Wu, Guizhen; Dong, Xiaoping

2016-03-01

The quality control process throughout the Ebola virus nucleic acid detection in Sierra Leone-China Friendship Biological Safety Laboratory (SLE-CHN Biosafety Lab) was described in detail, in order to comprehensively display the scientific, rigorous, accurate and efficient practice in detection of Ebola virus of first batch detection team in SLE-CHN Biosafety Lab. Firstly, the key points of laboratory quality control system was described, including the managements and organizing, quality control documents and information management, instrument, reagents and supplies, assessment, facilities design and space allocation, laboratory maintenance and biosecurity. Secondly, the application of quality control methods in the whole process of the Ebola virus detection, including before the test, during the test and after the test, was analyzed. The excellent and professional laboratory staffs, the implementation of humanized management are the cornerstone of the success; High-level biological safety protection is the premise for effective quality control and completion of Ebola virus detection tasks. And professional logistics is prerequisite for launching the laboratory diagnosis of Ebola virus. The establishment and running of SLE-CHN Biosafety Lab has landmark significance for the friendship between Sierra Leone and China, and the lab becomes the most important base for Ebola virus laboratory testing in Sierra Leone.

BIRCH: a user-oriented, locally-customizable, bioinformatics system.

PubMed

Fristensky, Brian

2007-02-09

Molecular biologists need sophisticated analytical tools which often demand extensive computational resources. While finding, installing, and using these tools can be challenging, pipelining data from one program to the next is particularly awkward, especially when using web-based programs. At the same time, system administrators tasked with maintaining these tools do not always appreciate the needs of research biologists. BIRCH (Biological Research Computing Hierarchy) is an organizational framework for delivering bioinformatics resources to a user group, scaling from a single lab to a large institution. The BIRCH core distribution includes many popular bioinformatics programs, unified within the GDE (Genetic Data Environment) graphic interface. Of equal importance, BIRCH provides the system administrator with tools that simplify the job of managing a multiuser bioinformatics system across different platforms and operating systems. These include tools for integrating locally-installed programs and databases into BIRCH, and for customizing the local BIRCH system to meet the needs of the user base. BIRCH can also act as a front end to provide a unified view of already-existing collections of bioinformatics software. Documentation for the BIRCH and locally-added programs is merged in a hierarchical set of web pages. In addition to manual pages for individual programs, BIRCH tutorials employ step by step examples, with screen shots and sample files, to illustrate both the important theoretical and practical considerations behind complex analytical tasks. BIRCH provides a versatile organizational framework for managing software and databases, and making these accessible to a user base. Because of its network-centric design, BIRCH makes it possible for any user to do any task from anywhere.

BIRCH: A user-oriented, locally-customizable, bioinformatics system

PubMed Central

Fristensky, Brian

2007-01-01

Background Molecular biologists need sophisticated analytical tools which often demand extensive computational resources. While finding, installing, and using these tools can be challenging, pipelining data from one program to the next is particularly awkward, especially when using web-based programs. At the same time, system administrators tasked with maintaining these tools do not always appreciate the needs of research biologists. Results BIRCH (Biological Research Computing Hierarchy) is an organizational framework for delivering bioinformatics resources to a user group, scaling from a single lab to a large institution. The BIRCH core distribution includes many popular bioinformatics programs, unified within the GDE (Genetic Data Environment) graphic interface. Of equal importance, BIRCH provides the system administrator with tools that simplify the job of managing a multiuser bioinformatics system across different platforms and operating systems. These include tools for integrating locally-installed programs and databases into BIRCH, and for customizing the local BIRCH system to meet the needs of the user base. BIRCH can also act as a front end to provide a unified view of already-existing collections of bioinformatics software. Documentation for the BIRCH and locally-added programs is merged in a hierarchical set of web pages. In addition to manual pages for individual programs, BIRCH tutorials employ step by step examples, with screen shots and sample files, to illustrate both the important theoretical and practical considerations behind complex analytical tasks. Conclusion BIRCH provides a versatile organizational framework for managing software and databases, and making these accessible to a user base. Because of its network-centric design, BIRCH makes it possible for any user to do any task from anywhere. PMID:17291351

Self-Reacting Friction Stir Welding for Aluminum Complex Curvature Applications

NASA Technical Reports Server (NTRS)

Brown, Randy J.; Martin, W.; Schneider, J.; Hartley, P. J.; Russell, Carolyn; Lawless, Kirby; Jones, Chip

2003-01-01

This viewgraph representation provides an overview of sucessful research conducted by Lockheed Martin and NASA to develop an advanced self-reacting friction stir technology for complex curvature aluminum alloys. The research included weld process development for 0.320 inch Al 2219, sucessful transfer from the 'lab' scale to the production scale tool and weld quality exceeding strenght goals. This process will enable development and implementation of large scale complex geometry hardware fabrication. Topics covered include: weld process development, weld process transfer, and intermediate hardware fabrication.

Achieving behavioral control with millisecond resolution in a high-level programming environment.

PubMed

Asaad, Wael F; Eskandar, Emad N

2008-08-30

The creation of psychophysical tasks for the behavioral neurosciences has generally relied upon low-level software running on a limited range of hardware. Despite the availability of software that allows the coding of behavioral tasks in high-level programming environments, many researchers are still reluctant to trust the temporal accuracy and resolution of programs running in such environments, especially when they run atop non-real-time operating systems. Thus, the creation of behavioral paradigms has been slowed by the intricacy of the coding required and their dissemination across labs has been hampered by the various types of hardware needed. However, we demonstrate here that, when proper measures are taken to handle the various sources of temporal error, accuracy can be achieved at the 1 ms time-scale that is relevant for the alignment of behavioral and neural events.

Numerical modeling studies of wake vortex transport and evolution within the planetary boundary layer

NASA Technical Reports Server (NTRS)

Lin, Yuh-Lang; Arya, S. Pal; Kaplan, Michael L.

1994-01-01

The proposed research involves four tasks. The first of these is to simulate accurately the turbulent processes in the atmospheric boundary layer. TASS was originally developed to study meso-gamma scale phenomena, such as tornadic storms, microbursts and windshear effects in terminal areas. Simulation of wake vortex evolution, however, will rely on appropriate representation of the physical processes in the surface layer and mixed layer. This involves two parts. First, a specified heat flux boundary condition must be implemented at the surface. Using this boundary condition, simulation results will be compared to experimental data and to other model results for validation. At this point, any necessary changes to the model will be implemented. Next, a surface energy budget parameterization will be added to the model. This will enable calculation of the surface fluxes by accounting for the radiative heat transfer to and from the ground and heat loss to the soil rather than simple specification of the fluxes. The second task involves running TASS with prescribed wake vortices in the initial condition. The vortex models will be supplied by NASA Langley Research Center. Sensitivity tests will be performed on different meteorological environments in the atmospheric boundary layer, which include stable, neutral, and unstable stratifications, calm and severe wind conditions, and dry and wet conditions. Vortex strength may be varied as well. Relevant non-dimensional parameters will include the following: Richardson number or Froude number, Bowen ratio, and height to length scale ratios. The model output will be analyzed and visualized to better understand the transport, decay, and growth rates of the wake vortices. The third task involves running simulations using observed data. MIT Lincoln Labs is currently planning field experiments at the Memphis airport to measure both meteorological conditions and wake vortex characteristics. Once this data becomes available, it can be used to validate the model for vortex behavior under different atmospheric conditions. The fourth task will be to simulate the wake in a more realistic environment covering a wider area. This will involve grid nesting, since high resolution will be required in the wake region but a larger total domain will be used. During the first allocation year, most of the first task will be accomplished.

Energy performance evaluation of ultrasonic pretreatment of organic solid waste in a pilot-scale digester.

PubMed

Rasapoor, Mazdak; Adl, Mehrdad; Baroutian, Saeid; Iranshahi, Zeynab; Pazouki, Mohammad

2018-04-30

It has been proven that ultrasonic pretreatment (UP) has positive effect on biogas generation from previous lab-scale studies. However, that is not always the case in larger scale processes. The purpose of this study was to evaluate the effectiveness of UP to biogas generation in terms of anaerobic digestion process and energy efficiency. Parameters including total solids (TS) and ultrasonic treatment operational parameters of organic solid waste (OSW) resulted from our past lab scale UP studies were applied in this study. OSW with 6-10% TS was treated using a lab-scale ultrasonic processor using various power densities (0.2-0.6 W/mL) at different time periods up to 30 min. Results of lab scale confirmed that OSW with 6% TS sonicated with 0.2 W/mL power density in 30 min gave the best outcome for the pilot scale experiment. To simulate the condition of an actual scale, in addition to energy analysis, two different organic loading rates (OLR), namely 500 and 1500 gVS/m 3 day were examined. The pilot digester was fed with OSW with or without the pretreatment based on the aforementioned specifications. The results showed that UP effectively improves biogas generation in terms of quantity and quality (CH 4 /CO 2 ). Furthermore, it decreases the time to reach the maximum cumulative biogas volume comparing to the untreated feed. The key achievement of this research has confirmed that although the relative increase in the energy gain by the influence of UP was more remarkable under the 500 gVS/m 3 day OLR, energy analysis showed a better energy gain and energy benefit as well as jumping in biogas yield up to 80% for UP treated OSW under 1500 gVS/m 3 day OLR. Copyright © 2018 Elsevier B.V. All rights reserved.

Design and implementation of laser target simulator in hardware-in-the-loop simulation system based on LabWindows/CVI and RTX

NASA Astrophysics Data System (ADS)

Tong, Qiujie; Wang, Qianqian; Li, Xiaoyang; Shan, Bin; Cui, Xuntai; Li, Chenyu; Peng, Zhong

2016-11-01

In order to satisfy the requirements of the real-time and generality, a laser target simulator in semi-physical simulation system based on RTX+LabWindows/CVI platform is proposed in this paper. Compared with the upper-lower computers simulation platform architecture used in the most of the real-time system now, this system has better maintainability and portability. This system runs on the Windows platform, using Windows RTX real-time extension subsystem to ensure the real-time performance of the system combining with the reflective memory network to complete some real-time tasks such as calculating the simulation model, transmitting the simulation data, and keeping real-time communication. The real-time tasks of simulation system run under the RTSS process. At the same time, we use the LabWindows/CVI to compile a graphical interface, and complete some non-real-time tasks in the process of simulation such as man-machine interaction, display and storage of the simulation data, which run under the Win32 process. Through the design of RTX shared memory and task scheduling algorithm, the data interaction between the real-time tasks process of RTSS and non-real-time tasks process of Win32 is completed. The experimental results show that this system has the strongly real-time performance, highly stability, and highly simulation accuracy. At the same time, it also has the good performance of human-computer interaction.

Therapeutic Role of Bmi-1 Inhibitors in Eliminating Prostate Tumor Stem Cells

DTIC Science & Technology

2015-10-01

antitumor activity in mouse xenografts did not exert toxic effects on normal tissues. BMI-1 targeted therapy when combined with taxotere resulted in...utilizing zebrafish xenografts (Sabaawy Lab) and prostate cancer cell lines (Bertino Lab), and 3) Confirmation of the antitumor activity of C-209...in mouse xenografts alone and upon combination with taxotere (Bertino Lab). The following tasks from the approved SOW were performed to achieve the

For Whom the Mind Wanders, and When, Varies Across Laboratory and Daily-Life Settings.

PubMed

Kane, Michael J; Gross, Georgina M; Chun, Charlotte A; Smeekens, Bridget A; Meier, Matt E; Silvia, Paul J; Kwapil, Thomas R

2017-09-01

Undergraduates ( N = 274) participated in a weeklong daily-life experience-sampling study of mind wandering after being assessed in the lab for executive-control abilities (working memory capacity; attention-restraint ability; attention-constraint ability; and propensity for task-unrelated thoughts, or TUTs) and personality traits. Eight times a day, electronic devices prompted subjects to report on their current thoughts and context. Working memory capacity and attention abilities predicted subjects' TUT rates in the lab, but predicted the frequency of daily-life mind wandering only as a function of subjects' momentary attempts to concentrate. This pattern replicates prior daily-life findings but conflicts with laboratory findings. Results for personality factors also revealed different associations in the lab and daily life: Only neuroticism predicted TUT rate in the lab, but only openness predicted mind-wandering rate in daily life (both predicted the content of daily-life mind wandering). Cognitive and personality factors also predicted dimensions of everyday thought other than mind wandering, such as subjective judgments of controllability of thought. Mind wandering in people's daily environments and TUTs during controlled and artificial laboratory tasks have different correlates (and perhaps causes). Thus, mind-wandering theories based solely on lab phenomena may be incomplete.

Pre-bent instruments used in single-port laparoscopic surgery versus conventional laparoscopic surgery: comparative study of performance in a dry lab.

PubMed

Miernik, Arkadiusz; Schoenthaler, Martin; Lilienthal, Kerstin; Frankenschmidt, Alexander; Karcz, Wojciech Konrad; Kuesters, Simon

2012-07-01

Different types of single-incision laparoscopic surgery (SILS) have become increasingly popular. Although SILS is technically even more challenging than conventional laparoscopy, published data of first clinical series seem to demonstrate the feasibility of these approaches. Various attempts have been made to overcome restrictions due to loss of triangulation in SILS by specially designed SILS-specific instruments. This study involving novices in a dry lab compared task performances between conventional laparoscopic surgery (CLS) and single-port laparoscopic surgery (SPLS) using newly designed pre-bent instruments. In this study, 90 medical students without previous experience in laparoscopic techniques were randomly assigned to undergo one of three procedures: CLS, SPLS using two pre-bent instruments (SPLS-pp), or SPLS using one pre-bent and one straight laparoscopic instrument (SPLS-ps). In the dry lab, the participants performed four typical laparoscopic tasks of increasing difficulty. Evaluation included performance times or number of completed tasks within a given time frame. All performances were videotaped and evaluated for unsuccessful attempts and unwanted interactions of instruments. Using subjective questionnaires, the participants rated difficulties with two-dimensional vision and coordination of instruments. Task performances were significantly better in the CLS group than in either SPLS group. The SPLS-ps group showed a tendency toward better performances than the SPLS-pp group, but the difference was not significant. Video sequences and participants` questionnaires showed instrument interaction as the major problem in the single-incision surgery groups. Although SILS is feasible, as shown in clinical series published by laparoscopically experienced experts, SILS techniques are demanding due to restrictions that come with the loss of triangulation. These can be compensated only partially by currently available SILS-designed instruments. The future of SILS depends on further improvements in the available equipment or the development of new approaches such as needlescopically assisted or robotically assisted procedures.

Optimizing physician access to surgical intensive care unit laboratory information through mobile computing.

PubMed

Strain, J J; Felciano, R M; Seiver, A; Acuff, R; Fagan, L

1996-01-01

Approximately 30 minutes of computer access time are required by surgical residents at Stanford University Medical Center (SUMC) to examine the lab values of all patients on a surgical intensive care unit (ICU) service, a task that must be performed several times a day. To reduce the time accessing this information and simultaneously increase the readability and currency of the data, we have created a mobile, pen-based user interface and software system that delivers lab results to surgeons in the ICU. The ScroungeMaster system, loaded on a portable tablet computer, retrieves lab results for a subset of patients from the central laboratory computer and stores them in a local database cache. The cache can be updated on command; this update takes approximately 2.7 minutes for all ICU patients being followed by the surgeon, and can be performed as a background task while the user continues to access selected lab results. The user interface presents lab results according to physiologic system. Which labs are displayed first is governed by a layout selection algorithm based on previous accesses to the patient's lab information, physician preferences, and the nature of the patient's medical condition. Initial evaluation of the system has shown that physicians prefer the ScroungeMaster interface to that of existing systems at SUMC and are satisfied with the system's performance. We discuss the evolution of ScroungeMaster and make observations on changes to physician work flow with the presence of mobile, pen-based computing in the ICU.

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research (GEGR) has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GEGR (prime contractor) was awardedmore » a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GEGR, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on Aspen Plus process modeling, has an estimated process efficiency of 6% higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the third annual technical progress report for the UFP program supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting October 1, 2002 and ending September 30, 2003. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, bench-scale experimental testing, process modeling, pilot-scale system design and assembly, and program management.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6% higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the thirteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL under Contract No. DE-FC26-00FT40974. This report summarizes program accomplishments for the period starting October 1, 2003 and ending December 31, 2003. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale assembly, pilot-scale demonstration and program management and technology transfer.« less

Laparoscopic baseline ability assessment by virtual reality.

PubMed

Madan, Atul K; Frantzides, Constantine T; Sasso, Lisa M

2005-02-01

Assessment of any surgical skill is time-consuming and difficult. Currently, there are no accepted metrics for most surgical skills, especially laparoscopic skills. Virtual reality has been utilized for laparoscopic training of surgical residents. Our hypothesis is that this technology can be utilized for laparoscopic ability metrics. This study involved medical students with no previous laparoscopic experience. All students were taken into a porcine laboratory in order to assess two operative tasks (measuring a piece of bowel and placing a piece of bowel into a laparoscopic bag). Then they were taken into an inanimate lab with a Minimally Invasive Surgery Trainer-Virtual Reality (MIST-VR). Each student repeatedly performed one task (placing a virtual reality ball into a receptacle). The students' scores and times from the animate lab were compared with average economy of movement and times from the MIST-VR. The MIST-VR scored both hands individually. Thirty-two first- and second-year medical students were included in the study. There was statistically significant (P < 0.05) correlation between 11 of 16 possible relationships between the virtual reality trainer and operative tasks. While not all of the possible relationships demonstrated statistically significant correlation, the majority of the possible relationships demonstrated statistically significant correlation. Virtual reality may be an avenue for measuring laparoscopic surgical ability.

Learning with Multiple Representations: Extending Multimedia Learning beyond the Lab

ERIC Educational Resources Information Center

Eilam, Billie; Poyas, Yael

2008-01-01

The present study extended multimedia learning principles beyond the lab to an ecologically valid setting (homework). Eighteen information cards were used to perform three homework tasks. The control group students learned from single representation (SR) cards that presented all information as printed text. The multiple representation (MR) group…

The Virtual Genetics Lab: A Freely-Available Open-Source Genetics Simulation

ERIC Educational Resources Information Center

White, Brian; Bolker, Ethan; Koolar, Nikunj; Ma, Wei; Maw, Naing Naing; Yu, Chung Ying

2007-01-01

This lab is a computer simulation of transmission genetics. It presents students with a genetic phenomenon--the inheritance of a randomly--selected trait. The students' task is to determine how this trait is inherited by designing their own crosses and analyzing the results produced by the software.

Technical memo, project 0-6132 : task 6 - test sections in the districts.

DOT National Transportation Integrated Search

2011-01-01

This Tech Memo provides a summary of the Lab Test, Distress Survey, and Construction Reports : for the RAP Test Sections in Laredo District. Based on extensive lab testing by TTI, the District : elected to use the TTI mix-design (5.0% PG 64-22 + Crus...

Performance and Results for Quartz Detector for the SuperHMS Spectrometer at Hall C Jefferson Lab

NASA Astrophysics Data System (ADS)

Griego, Benjamin F., Jr.

A quartz detector has been constructed to be part of the trigger system for the Super High Momentum Spectrometer (SHMS). The SHMS will play a pivotal role in carrying out the 12 -- GeV physics program at Hal -- C Jefferson Lab. The quartz hodoscope consists of twenty one fused silica bars. Each bar is 125 cm long, 5.5 cm wide, 2.5 cm thick, and is viewed by a UV -- sensitive PMT on each end. The quartz hodoscope's task is to provide a clean detection of charged particles, a high level of background suppression, and an accurate tracking efficiency determination. Initial test results of the quartz detectors which include light yield and position resolution will be presented.

On-Chip Biomedical Imaging

PubMed Central

Göröcs, Zoltán; Ozcan, Aydogan

2012-01-01

Lab-on-a-chip systems have been rapidly emerging to pave the way toward ultra-compact, efficient, mass producible and cost-effective biomedical research and diagnostic tools. Although such microfluidic and micro electromechanical systems achieved high levels of integration, and are capable of performing various important tasks on the same chip, such as cell culturing, sorting and staining, they still rely on conventional microscopes for their imaging needs. Recently several alternative on-chip optical imaging techniques have been introduced, which have the potential to substitute conventional microscopes for various lab-on-a-chip applications. Here we present a critical review of these recently emerging on-chip biomedical imaging modalities, including contact shadow imaging, lensfree holographic microscopy, fluorescent on-chip microscopy and lensfree optical tomography. PMID:23558399

Introductory labs; what they don't, should, and can teach (and why)

NASA Astrophysics Data System (ADS)

Wieman, Carl

2016-03-01

Introductory physics labs are widely used and expensive. They have a wide variety of potential learning goals, but these are seldom specified and less often measured if they are achieved. We cover three different research projects on introductory labs: 1) We have done cognitive task analyses of both experimental research in physics and instructional labs. The striking differences explain much of the unhappiness expressed by students with labs: 2) We have measured the effectiveness of two introductory physics lab courses specifically intended to teach the physics content covered in standard introductory courses on mechanics and E & M. As measured by course exams, the benefit is 0 +/-2% for both. 3) We show how it is possible to use lab courses to teach students to correctly evaluate physical models with uncertain data. Such quantitative critical thinking is an important skill that is not learned in typical lab courses, but is well learned by our modified lab instruction.

Achieving behavioral control with millisecond resolution in a high-level programming environment

PubMed Central

Asaad, Wael F.; Eskandar, Emad N.

2008-01-01

The creation of psychophysical tasks for the behavioral neurosciences has generally relied upon low-level software running on a limited range of hardware. Despite the availability of software that allows the coding of behavioral tasks in high-level programming environments, many researchers are still reluctant to trust the temporal accuracy and resolution of programs running in such environments, especially when they run atop non-real-time operating systems. Thus, the creation of behavioral paradigms has been slowed by the intricacy of the coding required and their dissemination across labs has been hampered by the various types of hardware needed. However, we demonstrate here that, when proper measures are taken to handle the various sources of temporal error, accuracy can be achieved at the one millisecond time-scale that is relevant for the alignment of behavioral and neural events. PMID:18606188

The Increasing Interest of ANAMMOX Research in China: Bacteria, Process Development, and Application

PubMed Central

Chai, Li-Yuan; Tang, Chong-Jian; Zheng, Ping; Min, Xiao-Bo; Yang, Zhi-Hui; Song, Yu-Xia

2013-01-01

Nitrogen pollution created severe environmental problems and increasingly has become an important issue in China. Since the first discovery of ANAMMOX in the early 1990s, this related technology has become a promising as well as sustainable bioprocess for treating strong nitrogenous wastewater. Many Chinese research groups have concentrated their efforts on the ANAMMOX research including bacteria, process development, and application during the past 20 years. A series of new and outstanding outcomes including the discovery of new ANAMMOX bacterial species (Brocadia sinica), sulfate-dependent ANAMMOX bacteria (Anammoxoglobus sulfate and Bacillus benzoevorans), and the highest nitrogen removal performance (74.3–76.7 kg-N/m3/d) in lab scale granule-based UASB reactors around the world were achieved. The characteristics, structure, packing pattern and floatation mechanism of the high-rate ANAMMOX granules in ANAMMOX reactors were also carefully illustrated by native researchers. Nowadays, some pilot and full-scale ANAMMOX reactors were constructed to treat different types of ammonium-rich wastewater including monosodium glutamate wastewater, pharmaceutical wastewater, and leachate. The prime objective of the present review is to elucidate the ongoing ANAMMOX research in China from lab scale to full scale applications, comparative analysis, and evaluation of significant findings and to set a design to usher ANAMMOX research in culmination. PMID:24381935

Implementing 'The Math You Need' in an Introductory Physical Geology Course at California State University East Bay

NASA Astrophysics Data System (ADS)

Moran, J. E.

2011-12-01

The wide range of abilities in the student population at California State University East Bay, with a significant fraction of students under-prepared and requiring mathematics remediation, is a challenge to including mathematical concepts and exercises in our introductory geoscience courses. Student expectations that a geoscience course will not include quantitative work may result in math-phobics choosing the course and resisting quantitative work when presented with it. Introductory courses that are required for Geology and Environmental Science majors are also designated as General Education, which gives rise to a student group with a wide range of abilities and expectations. This presentation will focus on implementation of a series of online math tutorials for students in introductory geoscience courses called 'The Math You Need' (TMYN; http://serc.carleton.edu/mathyouneed/index.html). The program is implemented in a Physical Geology course, in which 2/3 of the students are typically non-majors. The Physical Geology course has a three hour lab each week and the lab exercises and lab manual offer several opportunities for application of TMYN. Many of the lab exercises include graphing, profiling, working with map scales, converting units, or using equations to calculate some parameter or solve for an unknown. Six TMYN modules covering topics using density calculations as applied to mineral properties and isostasy, graphing as applied to rock properties, earthquake location, and radiometric dating, and calculation of rates as applied to plate movement, stream discharge, and groundwater flow, are assigned as pre-labs to be completed before lab classes. TMYN skills are reinforced during lectures and lab exercises, as close in time as possible to students' exposure via TMYN. Pre- and post-tests give a measure of the effectiveness of TMYN in improving students' quantitative literacy.

SNPassoc: an R package to perform whole genome association studies.

PubMed

González, Juan R; Armengol, Lluís; Solé, Xavier; Guinó, Elisabet; Mercader, Josep M; Estivill, Xavier; Moreno, Víctor

2007-03-01

The popularization of large-scale genotyping projects has led to the widespread adoption of genetic association studies as the tool of choice in the search for single nucleotide polymorphisms (SNPs) underlying susceptibility to complex diseases. Although the analysis of individual SNPs is a relatively trivial task, when the number is large and multiple genetic models need to be explored it becomes necessary a tool to automate the analyses. In order to address this issue, we developed SNPassoc, an R package to carry out most common analyses in whole genome association studies. These analyses include descriptive statistics and exploratory analysis of missing values, calculation of Hardy-Weinberg equilibrium, analysis of association based on generalized linear models (either for quantitative or binary traits), and analysis of multiple SNPs (haplotype and epistasis analysis). Package SNPassoc is available at CRAN from http://cran.r-project.org. A tutorial is available on Bioinformatics online and in http://davinci.crg.es/estivill_lab/snpassoc.

Subjective rating scales as a workload

NASA Technical Reports Server (NTRS)

Bird, K. L.

1981-01-01

A multidimensional bipolar-adjective rating scale is employed as a subjective measure of operator workload in the performance of a one-axis tracking task. The rating scale addressed several dimensions of workload, including cognitive, physical, and perceptual task loading as well as fatigue and stress effects. Eight subjects performed a one-axis tracking task (with six levels of difficulty) and rated these tasks on several workload dimensions. Performance measures were tracking error RMS (root-mean square) and the standard deviation of control stick output. Significant relationships were observed between these performance measures and skill required, task complexity, attention level, task difficulty, task demands, and stress level.

Edwin M. McMillan

Science.gov Websites

mixture. The separation of the different components in these compound earths has been no easy task, since terbium and dysprosium in the lanthanides. By irradiating different sorts of heavy atoms with neutrons Berkeley Lab Search Submit Web People Close About the Lab Leadership/Organization Calendar News Center

The Impact of Powerful Oral Language Lab on Chilean EFL Preservice Teachers

ERIC Educational Resources Information Center

Ward, Hsuying Chiou; Andruske, Cynthia Lee

2013-01-01

This exploratory qualitative case study reports the impact of using a public-speaking structure (Powerful Oral Language Lab [POLL]) in teaching preservice Chilean English pedagogy students. It describes how this task-based method of English as a Foreign Language (EFL) teacher training is related to language strategic competence. Twenty students…

Portable Anthrax Testing with Lab-in-a-Pocket

ScienceCinema

Finley, Melissa; Koskelo, Markku; Edwards, Thayne

2018-05-30

BaDx (Bacillus anthracis Diagnostics) is a lab-in-a-pocket device to sample, sense, and diagnose bacteria that cause anthrax. It accomplishes these tasks in environments with no power, refrigerated storage, or laboratory equipment. BaDx was designed to be used with minimal or no training, and to keep handlers safe.

Portable Anthrax Testing with Lab-in-a-Pocket

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finley, Melissa; Koskelo, Markku; Edwards, Thayne

2014-10-24

BaDx (Bacillus anthracis Diagnostics) is a lab-in-a-pocket device to sample, sense, and diagnose bacteria that cause anthrax. It accomplishes these tasks in environments with no power, refrigerated storage, or laboratory equipment. BaDx was designed to be used with minimal or no training, and to keep handlers safe.

Driving Objectives and High-level Requirements for KP-Lab Technologies

ERIC Educational Resources Information Center

Lakkala, Minna; Paavola, Sami; Toikka, Seppo; Bauters, Merja; Markannen, Hannu; de Groot, Reuma; Ben Ami, Zvi; Baurens, Benoit; Jadin, Tanja; Richter, Christoph; Zoserl, Eva; Batatia, Hadj; Paralic, Jan; Babic, Frantisek; Damsa, Crina; Sins, Patrick; Moen, Anne; Norenes, Svein Olav; Bugnon, Alexandra; Karlgren, Klas; Kotzinons, Dimitris

2008-01-01

One of the central goals of the KP-Lab project is to co-design pedagogical methods and technologies for knowledge creation and practice transformation in an integrative and reciprocal manner. In order to facilitate this process user tasks, driving objectives and high-level requirements have been introduced as conceptual tools to mediate between…

A System Approach to Navy Medical Education and Training. Volume 1

DTIC Science & Technology

1974-08-31

each of the four major pro - ducts complement one another, they form, in fact, a single major product, that of the technology for improved training...the course of determining the functional limits and con - tent areas peculiar to potentially delegable tasks, it is highly desirable to be able to...NISTOS CYTO CLINICAL X-RAY LAS AST LAB ASST LAB AS SI AS SL ABI ASITO LA LAB STMIL OPERATIONS PATIENT CARE OP -- PC -- GMo GMO M.D. M.D. M.D MD M

Conducting spoken word recognition research online: Validation and a new timing method.

PubMed

Slote, Joseph; Strand, Julia F

2016-06-01

Models of spoken word recognition typically make predictions that are then tested in the laboratory against the word recognition scores of human subjects (e.g., Luce & Pisoni Ear and Hearing, 19, 1-36, 1998). Unfortunately, laboratory collection of large sets of word recognition data can be costly and time-consuming. Due to the numerous advantages of online research in speed, cost, and participant diversity, some labs have begun to explore the use of online platforms such as Amazon's Mechanical Turk (AMT) to source participation and collect data (Buhrmester, Kwang, & Gosling Perspectives on Psychological Science, 6, 3-5, 2011). Many classic findings in cognitive psychology have been successfully replicated online, including the Stroop effect, task-switching costs, and Simon and flanker interference (Crump, McDonnell, & Gureckis PLoS ONE, 8, e57410, 2013). However, tasks requiring auditory stimulus delivery have not typically made use of AMT. In the present study, we evaluated the use of AMT for collecting spoken word identification and auditory lexical decision data. Although online users were faster and less accurate than participants in the lab, the results revealed strong correlations between the online and laboratory measures for both word identification accuracy and lexical decision speed. In addition, the scores obtained in the lab and online were equivalently correlated with factors that have been well established to predict word recognition, including word frequency and phonological neighborhood density. We also present and analyze a method for precise auditory reaction timing that is novel to behavioral research. Taken together, these findings suggest that AMT can be a viable alternative to the traditional laboratory setting as a source of participation for some spoken word recognition research.

The national labs and their future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crease, R.P.

National laboratories of the USA, born with the atomic age and raised to prominence by the need for scientific superiority during the long Cold War, are facing the most critical challenge: how best to support the nation's current need to improve its international competitiveness through superior technology The charge that the national laboratories are [open quotes]Cold War relics[close quotes] that have outlived their usefulness is based on a misunderstanding of their mission, says Robert P. Crease, historian for Brookhaven National laboratory. Three of the labs-Los Alamos, Sandia, and Lawrence Livermore- are weapons laboratories and their missions must change. Oak Ridge,more » Argonne, and Brookhaven laboratories are multipurpose: basic research facilities with a continuing role in the world of science The national laboratory system traces its origins to the Manhattan Project. Over the next half-century, America's national labs grew into part of the most effective scientific establishment in the world, a much-copied model for management of large-scale scientific programs. In the early years, each lab defined a niche in the complex world of reactors, accelerators, and high-energy proton and electron physics. In the 1970s, several labs worked on basic energy sciences to help solve a national energy crisis. Today, the labs are pressured to do more applied research-research to transfer to the private sector and will have to respond by devising more effective ways of coordinating basic and applied research. But, Crease warns, [open quotes]It also will be essential that any commitment to applied research not take place at the cost of reducing the wellspring of basic research from which so much applied research flows. [open quotes]Making a solid and persuasive case for the independent value of basic research, and for their own role in that enterprise, may be the most important task facing the laboratories in their next half-century,[close quotes].« less

Integrating Robotic Observatories into Astronomy Labs

NASA Astrophysics Data System (ADS)

Ruch, Gerald T.

2015-01-01

The University of St. Thomas (UST) and a consortium of five local schools is using the UST Robotic Observatory, housing a 17' telescope, to develop labs and image processing tools that allow easy integration of observational labs into existing introductory astronomy curriculum. Our lab design removes the burden of equipment ownership by sharing access to a common resource and removes the burden of data processing by automating processing tasks that are not relevant to the learning objectives.Each laboratory exercise takes place over two lab periods. During period one, students design and submit observation requests via the lab website. Between periods, the telescope automatically acquires the data and our image processing pipeline produces data ready for student analysis. During period two, the students retrieve their data from the website and perform the analysis. The first lab, 'Weighing Jupiter,' was successfully implemented at UST and several of our partner schools. We are currently developing a second lab to measure the age of and distance to a globular cluster.

An investigation of the efficacy of collaborative virtual reality systems for moderated remote usability testing.

PubMed

Chalil Madathil, Kapil; Greenstein, Joel S

2017-11-01

Collaborative virtual reality-based systems have integrated high fidelity voice-based communication, immersive audio and screen-sharing tools into virtual environments. Such three-dimensional collaborative virtual environments can mirror the collaboration among usability test participants and facilitators when they are physically collocated, potentially enabling moderated usability tests to be conducted effectively when the facilitator and participant are located in different places. We developed a virtual collaborative three-dimensional remote moderated usability testing laboratory and employed it in a controlled study to evaluate the effectiveness of moderated usability testing in a collaborative virtual reality-based environment with two other moderated usability testing methods: the traditional lab approach and Cisco WebEx, a web-based conferencing and screen sharing approach. Using a mixed methods experimental design, 36 test participants and 12 test facilitators were asked to complete representative tasks on a simulated online shopping website. The dependent variables included the time taken to complete the tasks; the usability defects identified and their severity; and the subjective ratings on the workload index, presence and satisfaction questionnaires. Remote moderated usability testing methodology using a collaborative virtual reality system performed similarly in terms of the total number of defects identified, the number of high severity defects identified and the time taken to complete the tasks with the other two methodologies. The overall workload experienced by the test participants and facilitators was the least with the traditional lab condition. No significant differences were identified for the workload experienced with the virtual reality and the WebEx conditions. However, test participants experienced greater involvement and a more immersive experience in the virtual environment than in the WebEx condition. The ratings for the virtual environment condition were not significantly different from those for the traditional lab condition. The results of this study suggest that participants were productive and enjoyed the virtual lab condition, indicating the potential of a virtual world based approach as an alternative to conventional approaches for synchronous usability testing. Copyright © 2017 Elsevier Ltd. All rights reserved.

Affective video retrieval: violence detection in Hollywood movies by large-scale segmental feature extraction.

PubMed

Eyben, Florian; Weninger, Felix; Lehment, Nicolas; Schuller, Björn; Rigoll, Gerhard

2013-01-01

Without doubt general video and sound, as found in large multimedia archives, carry emotional information. Thus, audio and video retrieval by certain emotional categories or dimensions could play a central role for tomorrow's intelligent systems, enabling search for movies with a particular mood, computer aided scene and sound design in order to elicit certain emotions in the audience, etc. Yet, the lion's share of research in affective computing is exclusively focusing on signals conveyed by humans, such as affective speech. Uniting the fields of multimedia retrieval and affective computing is believed to lend to a multiplicity of interesting retrieval applications, and at the same time to benefit affective computing research, by moving its methodology "out of the lab" to real-world, diverse data. In this contribution, we address the problem of finding "disturbing" scenes in movies, a scenario that is highly relevant for computer-aided parental guidance. We apply large-scale segmental feature extraction combined with audio-visual classification to the particular task of detecting violence. Our system performs fully data-driven analysis including automatic segmentation. We evaluate the system in terms of mean average precision (MAP) on the official data set of the MediaEval 2012 evaluation campaign's Affect Task, which consists of 18 original Hollywood movies, achieving up to .398 MAP on unseen test data in full realism. An in-depth analysis of the worth of individual features with respect to the target class and the system errors is carried out and reveals the importance of peak-related audio feature extraction and low-level histogram-based video analysis.

Selection of Yeasts as Starter Cultures for Table Olives: A Step-by-Step Procedure

PubMed Central

Bevilacqua, Antonio; Corbo, Maria Rosaria; Sinigaglia, Milena

2012-01-01

The selection of yeasts intended as starters for table olives is a complex process, including a characterization step at laboratory level and a validation at lab level and factory-scale. The characterization at lab level deals with the assessment of some technological traits (growth under different temperatures and at alkaline pHs, effect of salt, and for probiotic strains the resistance to preservatives), enzymatic activities, and some new functional properties (probiotic traits, production of vitamin B-complex, biological debittering). The paper reports on these traits, focusing both on their theoretical implications and lab protocols; moreover, there are some details on predictive microbiology for yeasts of table olives and on the use of multivariate approaches to select suitable starters. PMID:22666220

Evaluation of social interaction, task management, and trust among dental hygiene students in a collaborative learning environment.

PubMed

Saylor, Catherine D; Keselyak, Nancy T; Simmer-Beck, Melanie; Tira, Daniel

2011-02-01

The purpose of this study was to evaluate the impact of collaborative learning on the development of social interaction, task management, and trust in dental hygiene students. These three traits were assessed with the Teamwork Assessment Scale in two different learning environments (traditional lecture/lab and collaborative learning environment). A convenience sample of fifty-six entry-level dental hygiene students taking an introductory/preclinic course at two metropolitan area dental hygiene programs provided comparable experimental and control groups. Factor scores were computed for the three traits, and comparisons were conducted using the Ryan-Einot-Gabriel-Welsh multiple comparison procedure among specific cell comparisons generated from a two-factor repeated measures ANOVA. The results indicate that the collaborative learning environment influenced dental hygiene students positively regarding the traits of social interaction, task management, and trust. However, comparing dental hygiene students to undergraduate students overall indicates that dental hygiene students already possess somewhat higher levels of these traits. Future studies on active learning strategies should examine factors such as student achievement and explore other possible active learning methodologies.

Social Cognition in Williams Syndrome: Relations between Performance on the Social Attribution Task and Cognitive and Behavioral Characteristics.

PubMed

van der Fluit, Faye; Gaffrey, Michael S; Klein-Tasman, Bonita P

2012-01-01

Williams syndrome (WS) is a developmental disorder of genetic origin, with characteristic cognitive and personality profiles. Studies of WS point to an outgoing and gregarious personality style, often contrasted with autism spectrum disorders; however, recent research has uncovered underlying social reciprocity difficulties in people with WS. Social information processing difficulties that underlie these social reciprocity difficulties have been sparsely examined. Participants in the current study included 24 children with WS ages 8 through 15. A lab-based measure of social perception and social cognition was administered (Social Attribution Test), as well as an intellectual functioning measure (KBIT-II) and parent reports of communication and reciprocal social skills (Social Communication Questionnaire, Social Responsiveness Scale). Relations between social cognition, cognitive abilities, and social-communication were examined. Results demonstrated relations between parent-reported social reciprocity and the typicality of the responses provided in the lab-based measure, even once variability in intellectual functioning was taken into account. Specifically, those individuals who produced narratives in response to the social attribution task (SAT) that were more similar to those described in previous studies of typically developing individuals were also reported to have fewer social reciprocity difficulties in the real world setting as reported by parents. In addition, a significant improvement in performance on the SAT was seen with added scaffolding, particularly for participants with stronger intellectual functioning. These findings indicate that difficulties interpreting the social dynamics between others in ambiguous situations may contribute to the social relationship difficulties observed in people with WS, above and beyond the role of intellectual functioning. Exploratory analyses indicated that performance by individuals with stronger intellectual functioning is improved with additional structure to a greater degree than for those with weaker intellectual functioning. Interventions that specifically target these social information processing of individuals with WS would likely be beneficial.

Social Cognition in Williams Syndrome: Relations between Performance on the Social Attribution Task and Cognitive and Behavioral Characteristics

PubMed Central

van der Fluit, Faye; Gaffrey, Michael S.; Klein-Tasman, Bonita P.

2012-01-01

Williams syndrome (WS) is a developmental disorder of genetic origin, with characteristic cognitive and personality profiles. Studies of WS point to an outgoing and gregarious personality style, often contrasted with autism spectrum disorders; however, recent research has uncovered underlying social reciprocity difficulties in people with WS. Social information processing difficulties that underlie these social reciprocity difficulties have been sparsely examined. Participants in the current study included 24 children with WS ages 8 through 15. A lab-based measure of social perception and social cognition was administered (Social Attribution Test), as well as an intellectual functioning measure (KBIT-II) and parent reports of communication and reciprocal social skills (Social Communication Questionnaire, Social Responsiveness Scale). Relations between social cognition, cognitive abilities, and social-communication were examined. Results demonstrated relations between parent-reported social reciprocity and the typicality of the responses provided in the lab-based measure, even once variability in intellectual functioning was taken into account. Specifically, those individuals who produced narratives in response to the social attribution task (SAT) that were more similar to those described in previous studies of typically developing individuals were also reported to have fewer social reciprocity difficulties in the real world setting as reported by parents. In addition, a significant improvement in performance on the SAT was seen with added scaffolding, particularly for participants with stronger intellectual functioning. These findings indicate that difficulties interpreting the social dynamics between others in ambiguous situations may contribute to the social relationship difficulties observed in people with WS, above and beyond the role of intellectual functioning. Exploratory analyses indicated that performance by individuals with stronger intellectual functioning is improved with additional structure to a greater degree than for those with weaker intellectual functioning. Interventions that specifically target these social information processing of individuals with WS would likely be beneficial. PMID:22737137

Taking Battery Technology from the Lab to the Big City

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banerjee, Sanjoy; Shmukler, Michael; Martin, Cheryl

2013-07-29

Urban Electric Power, a startup formed by researchers from the City University of New York (CUNY) Energy Institute, is taking breakthroughs in battery technology from the lab to the market. With industry and government funding, including a grant from the Energy Department, Urban Electric Power developed a zinc-nickel oxide battery electrolyte that circulates constantly, eliminating dendrite formation and preventing battery shortages. Their new challenge is to take this technology to the market, where they can scale up the batteries for reducing peak energy demand in urban areas and storing variable renewable electricity.

Taking Battery Technology from the Lab to the Big City

ScienceCinema

Banerjee, Sanjoy; Shmukler, Michael; Martin, Cheryl

2018-02-02

Urban Electric Power, a startup formed by researchers from the City University of New York (CUNY) Energy Institute, is taking breakthroughs in battery technology from the lab to the market. With industry and government funding, including a grant from the Energy Department, Urban Electric Power developed a zinc-nickel oxide battery electrolyte that circulates constantly, eliminating dendrite formation and preventing battery shortages. Their new challenge is to take this technology to the market, where they can scale up the batteries for reducing peak energy demand in urban areas and storing variable renewable electricity.

Cognitive Task Analysis: Implications for the Theory and Practice of Instructional Design.

ERIC Educational Resources Information Center

Dehoney, Joanne

Cognitive task analysis grew out of efforts by cognitive psychologists to understand problem-solving in a lab setting. It has proved a useful tool for describing expert performance in complex problem solving domains. This review considers two general models of cognitive task analysis and examines the procedures and results of analyses in three…

Hand controller study of force and control mode

NASA Technical Reports Server (NTRS)

Morris, A. Terry

1992-01-01

The objectives are to compare and evaluate the utility and effectiveness of various input control devices, e.g., hand controllers, with respect to the relative importance of force and operation control mode (rate or position) for Space Station Freedom (SSF) related tasks. The topics are presented in viewgraph form and include the: Intelligent Research Systems Lab (ISRL) experimental design; Telerobotic Systems Research Laboratory (TSRL) final experimental design; and factor analysis summary of results.

Single-Pilot Workload Management

NASA Technical Reports Server (NTRS)

Rogers, Jason; Williams, Kevin; Hackworth, Carla; Burian, Barbara; Pruchnicki, Shawn; Christopher, Bonny; Drechsler, Gena; Silverman, Evan; Runnels, Barry; Mead, Andy

2013-01-01

Integrated glass cockpit systems place a heavy cognitive load on pilots (Burian Dismukes, 2007). Researchers from the NASA Ames Flight Cognition Lab and the FAA Flight Deck Human Factors Lab examined task and workload management by single pilots. This poster describes pilot performance regarding programming a reroute while at cruise and meeting a waypoint crossing restriction on the initial descent.

A Role-Playing Game for a Software Engineering Lab: Developing a Product Line

ERIC Educational Resources Information Center

Zuppiroli, Sara; Ciancarini, Paolo; Gabbrielli, Maurizio

2012-01-01

Software product line development refers to software engineering practices and techniques for creating families of similar software systems from a basic set of reusable components, called shared assets. Teaching how to deal with software product lines in a university lab course is a challenging task, because there are several practical issues that…

Lab Reports: A Concise Guide for Non-Native English Speakers

ERIC Educational Resources Information Center

Soundranayagam, Luxshmi

2014-01-01

College students in the non-English-speaking world have to overcome formidable barriers in reading and writing when their medium of instruction is English. One particular problem faced by science majors is the writing of lab reports, a demanding task that might not be effectively supported by the standard guides and manuals available. This paper…

EJS, JIL Server, and LabVIEW: An Architecture for Rapid Development of Remote Labs

ERIC Educational Resources Information Center

Chacón, Jesús; Vargas, Hector; Farias, Gonzalo; Sanchez, José; Dormido, Sebastián

2015-01-01

Designing and developing web-enabled remote laboratories for pedagogical purposes is not an easy task. Often, developers (generally, educators who know the subjects they teach but lack of the technical and programming skills required to build Internet-based educational applications) end up discarding the idea of exploring these new teaching and…

Embracing Learners' Ideas about Diffusion and Osmosis: A Coupled-Inquiry Approach

ERIC Educational Resources Information Center

Sweeney, Ryan M.; Martin-Hansen, Lisa; Verma, Geeta; Dunkhase, John

2009-01-01

Learning about osmosis and diffusion is often a challenging task for middle school students. Here the authors present a lesson that was converted from a "cookbook" lab (McLaughlin and Thompson 2007) into a more inquiry-oriented lab that uses inquiry teaching strategies and hands-on investigations to teach middle-grade students about osmosis and…

Comparison of lab, pilot, and industrial scale low consistency mechanical refining for improvements in enzymatic digestibility of pretreated hardwood.

PubMed

Jones, Brandon W; Venditti, Richard; Park, Sunkyu; Jameel, Hasan

2014-09-01

Mechanical refining has been shown to improve biomass enzymatic digestibility. In this study industrial high-yield sodium carbonate hardwood pulp was subjected to lab, pilot and industrial refining to determine if the mechanical refining improves the enzymatic hydrolysis sugar conversion efficiency differently at different refining scales. Lab, pilot and industrial refining increased the biomass digestibility for lignocellulosic biomass relative to the unrefined material. The sugar conversion was increased from 36% to 65% at 5 FPU/g of biomass with industrial refining at 67.0 kWh/t, which was more energy efficient than lab and pilot scale refining. There is a maximum in the sugar conversion with respect to the amount of refining energy. Water retention value is a good predictor of improvements in sugar conversion for a given fiber source and composition. Improvements in biomass digestibility with refining due to lab, pilot plant and industrial refining were similar with respect to water retention value. Published by Elsevier Ltd.

A questionnaire approach to measuring the relative reinforcing efficacy of snack foods

PubMed Central

Epstein, Leonard H.; Dearing, Kelly K.; Roba, Lora G.

2010-01-01

Behavioral choice theory and laboratory choice paradigms can provide a framework to understand the reinforcing efficacy or reinforcing value of food. Reinforcing efficacy is measured in the laboratory by assessing how much effort one will engage in to gain access to food as the amount of work progressively increases. However, this method to establish demand curves as estimates of reinforcer efficacy is time consuming and limits the number of reinforcers that can be tested. The general aim of this study was to compare the reinforcing efficacy of snack foods using a behavioral task that requires subjects to respond to gain access to portions of food (LAB task) with a questionnaire version of a purchasing task designed to determine demand curves (QUES task) in nonobese and obese adults (n = 24). Results showed correlations between the maximal amount of money that individuals were willing to spend for food (QUES Omax) and the maximal amount of responses made on the highest reinforcement schedule completed (LAB Omax) (r = 0.45, p < 0.05), and between BMI and the LAB Omax (r = 0.43, p < 0.05) and the QUES Omax (r = 0.52, p < 0.05). The study suggests the questionnaire provides valid measures of reinforcing efficacy that can be used in place of or in conjunction with traditional laboratory paradigms to establish demand curves that describe the behavioral maintaining properties of food. PMID:20188288

Meta-analysis of effects of inoculation with homofermentative and facultative heterofermentative lactic acid bacteria on silage fermentation, aerobic stability, and the performance of dairy cows.

PubMed

Oliveira, André S; Weinberg, Zwi G; Ogunade, Ibukun M; Cervantes, Andres A P; Arriola, Kathy G; Jiang, Yun; Kim, Donghyeon; Li, Xujiao; Gonçalves, Mariana C M; Vyas, Diwakar; Adesogan, Adegbola T

2017-06-01

Forages are usually inoculated with homofermentative and facultative heterofermentative lactic acid bacteria (LAB) to enhance lactic acid fermentation of forages, but effects of such inoculants on silage quality and the performance of dairy cows are unclear. Therefore, we conducted a meta-analysis to examine the effects of LAB inoculation on silage quality and preservation and the performance of dairy cows. A second objective was to examine the factors affecting the response to silage inoculation with LAB. The studies that met the selection criteria included 130 articles that examined the effects of LAB inoculation on silage quality and 31 articles that investigated dairy cow performance responses. The magnitude of the effect (effect size) was evaluated using raw mean differences (RMD) between inoculated and uninoculated treatments. Heterogeneity was explored by meta-regression and subgroup analysis using forage type, LAB species, LAB application rate, and silo scale (laboratory or farm-scale) as covariates for the silage quality response and forage type, LAB species, diet type [total mixed ration (TMR) or non-TMR], and the level of milk yield of the control cows as covariates for the performance responses. Inoculation with LAB (≥10 5 cfu/g as fed) markedly increased silage fermentation and dry matter recovery in temperate and tropical grasses, alfalfa, and other legumes. However, inoculation did not improve the fermentation of corn, sorghum, or sugarcane silages. Inoculation with LAB reduced clostridia and mold growth, butyric acid production, and ammonia-nitrogen in all silages, but it had no effect on aerobic stability. Silage inoculation (≥10 5 cfu/g as fed) increased milk yield and the response had low heterogeneity. However, inoculation had no effect on diet digestibility and feed efficiency. Inoculation with LAB improved the fermentation of grass and legume silages and the performance of dairy cows but did not affect the fermentation of corn, sorghum, and sugar cane silages or the aerobic stability of any silage. Further research is needed to elucidate how silage inoculated with homofermentative and facultative heterofermentative LAB improves the performance of dairy cows. The Authors. Published by the Federation of Animal Science Societies and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

Ozone Contamination in Aircraft Cabins: Appendix B: Overview papers. Ozone destruction techniques

NASA Technical Reports Server (NTRS)

Wilder, R.

1979-01-01

Ozone filter test program and ozone instrumentation are presented. Tables on the flight tests, samll scale lab tests, and full scale lab tests were reviewed. Design verification, flammability, vibration, accelerated contamination, life cycle, and cabin air quality are described.

Lab-Scale Stimulation Results on Surrogate Fused Silica Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlos Fernandez

Lab-scale stimulation work on non-porous fused silica (similar mechanical properties to igneous rock) was performed using pure water, pure CO2 and water/CO2 mixtures to compare back to back fracturing performance of these fluids with PNNL's StimuFrac.

Using hypermedia to develop an intelligent tutorial/diagnostic system for the Space Shuttle Main Engine Controller Lab

NASA Technical Reports Server (NTRS)

Oreilly, Daniel; Williams, Robert; Yarborough, Kevin

1988-01-01

This is a tutorial/diagnostic system for training personnel in the use of the Space Shuttle Main Engine Controller (SSMEC) Simulation Lab. It also provides a diagnostic capable of isolating lab failures at least to the major lab component. The system was implemented using Hypercard, which is an program of hypermedia running on Apple Macintosh computers. Hypercard proved to be a viable platform for the development and use of sophisticated tutorial systems and moderately capable diagnostic systems. This tutorial/diagnostic system uses the basic Hypercard tools to provide the tutorial. The diagnostic part of the system uses a simple interpreter written in the Hypercard language (Hypertalk) to implement the backward chaining rule based logic commonly found in diagnostic systems using Prolog. Some of the advantages of Hypercard in developing this type of system include sophisticated graphics, animation, sound and voice capabilities, its ability as a hypermedia tool, and its ability to include digitized pictures. The major disadvantage is the slow execution time for evaluation of rules (due to the interpretive processing of the language). Other disadvantages include the limitation on the size of the cards, that color is not supported, that it does not support grey scale graphics, and its lack of selectable fonts for text fields.

Inductance Scaling of a Helicoil Using ALEGRA

DTIC Science & Technology

2013-05-01

HOUSKAMP 3 US ARMY RESEARCH LAB RDRL WMP E P BARTKOWSKI D HORNBAKER P SWOBODA 1 US ARMY RESEARCH LAB RDRL WMP F N GNIAZDOWSKI 1 US ARMY RESEARCH LAB RDRL...HAILL 1 UNIVERSITY OF ALABAMA AT BIRMINGHAM D LITTLEFIELD 1 DEFENSE RESEARCH AGENCY B JAMES 2 ENIG ASSOCIATES, INC. E ENIG D BENTZ 42 ...January 2012 Inductance Scaling of a Helicoil Using ALEGRA Robert Doney U.S. Army Research Laboratory ATTN: RDRL-WMP- D Aberdeen Proving Ground, MD 21005

Continuous leg dyskinesia assessment in Parkinson's disease -clinical validity and ecological effect.

PubMed

Ramsperger, Robert; Meckler, Stefan; Heger, Tanja; van Uem, Janet; Hucker, Svenja; Braatz, Ulrike; Graessner, Holm; Berg, Daniela; Manoli, Yiannos; Serrano, J Artur; Ferreira, Joaquim J; Hobert, Markus A; Maetzler, Walter

2016-05-01

Dyskinesias in Parkinson's disease (PD) patients are a common side effect of long-term dopaminergic therapy and are associated with motor dysfunctions, including gait and balance deficits. Although promising compounds have been developed to treat these symptoms, clinical trials have failed. This failure may, at least partly, be explained by the lack of objective and continuous assessment strategies. This study tested the clinical validity and ecological effect of an algorithm that detects and quantifies dyskinesias of the legs using a single ankle-worn sensor. Twenty-three PD patients (seven with leg dyskinesias) and 13 control subjects were investigated in the lab. Participants performed purposeful daily activity-like tasks while being video-taped. Clinical evaluation was performed using the leg dyskinesia item of the Unified Dyskinesia Rating Scale. The ecological effect of the developed algorithm was investigated in a multi-center, 12-week, home-based sub-study that included three patients with and seven without dyskinesias. In the lab-based sub-study, the sensor-based algorithm exhibited a specificity of 98%, a sensitivity of 85%, and an accuracy of 0.96 for the detection of dyskinesias and a correlation level of 0.61 (p < 0.001) with the clinical severity score. In the home-based sub-study, all patients could be correctly classified regarding the presence or absence of leg dyskinesias, supporting the ecological relevance of the algorithm. This study provides evidence of clinical validity and ecological effect of an algorithm derived from a single sensor on the ankle for detecting leg dyskinesias in PD patients. These results should motivate the investigation of leg dyskinesias in larger studies using wearable sensors. Copyright © 2016 Elsevier Ltd. All rights reserved.

The experiment editor: supporting inquiry-based learning with virtual labs

NASA Astrophysics Data System (ADS)

Galan, D.; Heradio, R.; de la Torre, L.; Dormido, S.; Esquembre, F.

2017-05-01

Inquiry-based learning is a pedagogical approach where students are motivated to pose their own questions when facing problems or scenarios. In physics learning, students are turned into scientists who carry out experiments, collect and analyze data, formulate and evaluate hypotheses, and so on. Lab experimentation is essential for inquiry-based learning, yet there is a drawback with traditional hands-on labs in the high costs associated with equipment, space, and maintenance staff. Virtual laboratories are helpful to reduce these costs. This paper enriches the virtual lab ecosystem by providing an integrated environment to automate experimentation tasks. In particular, our environment supports: (i) scripting and running experiments on virtual labs, and (ii) collecting and analyzing data from the experiments. The current implementation of our environment supports virtual labs created with the authoring tool Easy Java/Javascript Simulations. Since there are public repositories with hundreds of freely available labs created with this tool, the potential applicability to our environment is considerable.

Developing Strategies to Block Beta-Catenin Action in Signaling and Cell Adhesion During Carcinogenesis

DTIC Science & Technology

2002-07-01

this section was published in a paper from our lab in Molecular Biology of the Cell (Simcha et al., 2001)--below we refer to Figures in this paper...work, both in yeast and in mammalian cells, were recently published in Molecular Biology of the Cell (Simcha et al., 2001), and the work from our lab ...detail genetic and molecular interactions between gro, wg ,arm and dTCF (task 2 and 4 above)- this work was a collaboration with the labs of Amy

Removal characteristics of pharmaceuticals and personal care products: Comparison between membrane bioreactor and various biological treatment processes.

PubMed

Park, Junwon; Yamashita, Naoyuki; Park, Chulhwi; Shimono, Tatsumi; Takeuchi, Daniel M; Tanaka, Hiroaki

2017-07-01

We investigated the concentrations of 57 target compounds in the different treatment units of various biological treatment processes in South Korea, including modified biological nutrient removal (BNR), anaerobic-anoxic-aerobic (A2O), and membrane bioreactor (MBR) systems, to elucidate the occurrence and removal fates of PPCPs in WWTPs. Biological treatment processes appeared to be most effective in eliminating most PPCPs, whereas some PPCPs were additionally removed by post-treatment. With the exception of the MBR process, the A2O system was effective for PPCPs removal. As a result, removal mechanisms were evaluated by calculating the mass balances in A2O and a lab-scale MBR process. The comparative study demonstrated that biodegradation was largely responsible for the improved removal performance found in lab-scale MBR (e.g., in removing bezafibrate, ketoprofen, and atenolol). Triclocarban, ciprofloxacin, levofloxacin and tetracycline were adsorbed in large amounts to MBR sludge. Increased biodegradability was also observed in lab-scale MBR, despite the highly adsorbable characteristics. The enhanced biodegradation potential seen in the MBR process thus likely plays a key role in eliminating highly adsorbable compounds as well as non-degradable or persistent PPCPs in other biological treatment processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Providing Guidance in Virtual Lab Experimentation: The Case of an Experiment Design Tool

ERIC Educational Resources Information Center

Efstathiou, Charalampos; Hovardas, Tasos; Xenofontos, Nikoletta A.; Zacharia, Zacharias C.; deJong, Ton; Anjewierden, Anjo; van Riesen, Siswa A. N.

2018-01-01

The present study employed a quasi-experimental design to assess a computer-based tool, which was intended to scaffold the task of designing experiments when using a virtual lab for the process of experimentation. In particular, we assessed the impact of this tool on primary school students' cognitive processes and inquiry skills before and after…

Low cost lab-on-a-chip prototyping with a consumer grade 3D printer.

PubMed

Comina, Germán; Suska, Anke; Filippini, Daniel

2014-08-21

Versatile prototyping of 3D printed lab-on-a-chip devices, supporting different forms of sample delivery, transport, functionalization and readout, is demonstrated with a consumer grade printer, which centralizes all critical fabrication tasks. Devices cost 0.57US$ and are demonstrated in chemical sensing and micromixing examples, which exploit established principles from reference technologies.

Excellence in Physics Education Award: SCALE-UP, Student Centered Active Learning Environment with Upside-down Pedagogies

NASA Astrophysics Data System (ADS)

Beichner, Robert

2016-03-01

The Student-Centered Active Learning Environment with Upside-down Pedagogies (SCALE-UP) Project combines curricula and a specially-designed instructional space to enhance learning. SCALE-UP students practice communication and teamwork skills while performing activities that enhance their conceptual understanding and problem solving skills. This can be done with small or large classes and has been implemented at more than 250 institutions. Educational research indicates that students should collaborate on interesting tasks and be deeply involved with the material they are studying. SCALE-UP classtime is spent primarily on ``tangibles'' and ``ponderables''--hands-on measurements/observations and interesting questions. There are also computer simulations (called ``visibles'') and hypothesis-driven labs. Students sit at tables designed to facilitate group interactions. Instructors circulate and engage in Socratic dialogues. The setting looks like a banquet hall, with lively interactions nearly all the time. Impressive learning gains have been measured at institutions across the US and internationally. This talk describes today's students, how lecturing got started, what happens in a SCALE-UP classroom, and how the approach has spread. The SCALE-UP project has greatly benefitted from numerous Grants made by NSF and FIPSE to NCSU and other institutions.

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6 percentage points higher than IGCC with conventional CO{sub 2} separation. The current R&D program will determine the feasibility of the integrated UFP technology through pilot-scale testing, and will investigate operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the fourteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974) and GE. This report summarizes program accomplishments for the period starting January 1, 2004 and ending March 31, 2004. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale shakedown and performance testing, program management and technology transfer.« less

FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Arnaldo Frydman

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE Global Research (prime contractor) wasmore » awarded a contract from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE Global Research, Southern Illinois University at Carbondale (SIU-C), California Energy Commission (CEC), and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on ASPEN Plus process modeling, has an estimated process efficiency of 6 percentage points higher than IGCC with conventional CO{sub 2} separation. The current R&D program has determined the feasibility of the integrated UFP technology through pilot-scale testing, and investigated operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrated experimental testing, modeling and economic studies to demonstrate the UFP technology. This is the fifteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974) and GE. This report summarizes program accomplishments for the period starting April 1, 2004 and ending June 30, 2004. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab-scale experimental testing, pilot-scale testing, kinetic modeling, program management and technology transfer.« less

Ups and downs of using ``kitchen sink'' experiments in an introductory fluid mechanics class

NASA Astrophysics Data System (ADS)

Kaye, Nigel

2015-11-01

Both positive and negative experiences from two semesters of using take home ``kitchen sink'' experiments in an introductory civil engineering fluid mechanics class are reported. Four different experimental assignments were given each semester to groups of four students. The students were tasked with using common household equipment to measure various properties of fluids or fluid flows. These included the density of cooking oil, the exit velocity from a garden hose, and the mass flux of air from a compressed air can. Students were given minimal guidance on how to do the measurements and each measurement had to be done in at least two different ways. The labs were used to relate their course work to everyday situations and was also used as a platform for discussing experimental uncertainty and error propagation in calculations. In general the students successfully completed each task using at least one method. Finding a second method sometimes proved problematic. The presentation will discuss the logistics of running the program and the positive and negative aspects from the instructor viewpoint. A summary of student feedback on the labs will also be presented. Links to resources for those interested in implementing such a program will be provided.

SAGES Mini Med School: inspiring high school students through exposure to the field of surgery.

PubMed

Rosser, James C; Legare, Timothy B; Jacobs, Charles; Choi, Katherine M; Fleming, Jeffrey P; Nakagiri, Jamie

2018-04-02

The SAGES Mini Med School (SMMS) was designed to expose high school students to the field of surgery through mentoring, knowledge transfer, and hands-on experience with simulation. The objective of this paper is to profile the evolutionary development, performance metrics, and satisfaction queries of this innovative effort. Sixty-one high school students, grades 9-12, took part in the (SMMS) program during the 2015 SAGES Annual Congress. The students completed a surgical skills lab session where they attempted tasks associated with the development of open surgical and laparoscopic skills. The lab included a warm-up with the validated Super Monkey Ball video game, Top Gun Pea Drop task, FLS Peg Transfer task, open knot tying station, and open instrument tie station. The following are the results of the surgical skills lab. For the Super Monkey Ball task, 60 students participated with an average score of 73.0 s (SD = 53.9; range 59.1-87.0; median = 74). Sixty students participated in the Surgeons Knot and Pea Drop tasks with average times of 26.6 s (SD = 19.3; range 21.7-31.6; median = 21.0) and 113.8 s (SD = 65.9; range 96.6-131.0; median = 101.0), respectively. Sixty students participated in the Instrument Tie and 56 students participated in the Peg Transfer stations with average times of 51.7 s (SD = 34.5; range 42.8-60.6; median = 39.5) and 173.1 s (SD = 25.0; range 166.4-179.8; median = 180.0), respectively. 51 (83.6%) agreed that the Mini Med School made them more likely to consider a career in medicine. When asked if the program made them more likely to consider a career in surgery 42 (68.8%) agreed. All 61 respondents (100%) said that they would recommend the program to others. The SMMS program showed that the students had an excellent aptitude for the performance of validated surgical subtasks with high satisfaction, and increased consideration of a career in medicine/surgery. Long-term studies are needed to evaluate the impact on workforce recruitment.

From experiment to publication in one semester: a lecture course model on the basis of a photonic researcher's every-day tasks

NASA Astrophysics Data System (ADS)

Gerhard, Christoph; Wieneke, Stephan

2015-10-01

We report on a lecture course model that we established three semesters ago in order to strengthen practice-orientated teaching in optics and photonics: In the frame of the lecture "Advanced Laser Treatment", which is a mandatory course of our university's master degree curriculum, students now have the possibility to experience a researcher's every-day tasks. In small groups, the attendees work on a self-contained topic which is defined by the lecturers. The work load and content is in the scale of a small work package of a usual research project. It includes the initial research on the state of the art, the experimentation using different laser sources, and the subsequent evaluation of the obtained results. On the basis of this work, the students then prepare a draft of a scientific paper and finally present their results and findings orally in a conference-like exam. This lecture course model has turned out to be an appropriate teaching method for practice-orientated subjects. It was observed that the students are much more motivated and work more independently than during a classical lecture with a certain amount of lab work. Having sole responsibility supports to identify with their project. Further, this lecture course model helps to develop scientific work skills, attain first experience in every-day research tasks and encourages creativity. In some cases, the paper drafts written by the students can even be published, representing a valuable starting point for their future professional career.

Lab-scaled model to evaluate odor and gas production from cattle confinement facilities with deep bedded packs

USDA-ARS?s Scientific Manuscript database

A lab-scaled simulated bedded pack model was developed to study air quality and nutrient composition of deep-bedded packs found in cattle monoslope facilities. This protocol has been used to effectively evaluate many different bedding materials, environmental variables (temperature, humidity), and ...

The College of Charleston's 400-Student Observational Lab Program

NASA Astrophysics Data System (ADS)

True, C. M.

2006-06-01

For over thirty years the College of Charleston has been teaching a year-long introductory astronomy course incorporating a mandatory 3 hour lab. Despite our location in a very light polluted, coastal, high humidity, and often cloudy metropolitan area we have emphasized observational activities as much as possible. To accommodate our population of between 300-400 students per semester, we have 28 8-inch Celestron Telescopes and 25 GPS capable 8-inch Meade LX-200 telescopes. Finally, we have a 16 DFM adjacent to our rooftop observing decks. For indoor activities we have access to 42 computers running a variety of astronomy education software. Some of the computer activities are based on the Starry Night software (Backyard and Pro), the CLEA software from Gettysburg College, and Spectrum Explorer from Boston University. Additionally, we have labs involving cratering, eclipses and phases, coordinate systems with celestial globes, the inverse square law, spectroscopy and spectral classification, as well as others. In this presentation we will discuss the difficulties in managing a program of this size. We have approximately 14 lab sections a week. The lab manager's task involves coordinating 8-10 lab instructors and the same number of undergraduate teaching assistants as well as trying to maintain a coherent experience between the labs and lecture sections. Our lab manuals are produced locally with yearly updates. Samples from the manuals will be available. This program has been developed by a large number of College of Charleston astronomy faculty, including Don Drost, Bob Dukes, Chris Fragile, Tim Giblin, Jon Hakkila, Bill Kubinec, Lee Lindner, Jim Neff, Laura Penny, Al Rainis, Terry Richardson, and D. J. Williams, as well as adjunct and visiting faculty Bill Baird, Kevin Bourque, Ethan Denault, Kwayera Davis, Francie Halter, and Alan Johnson. Part of this work has been funded by NSF DUE grants to the College of Charleston.

Peers at work: Evidence from the lab

PubMed Central

Oosterbeek, Hessel; Sonnemans, Joep

2018-01-01

This paper reports the results of a lab experiment designed to study the role of observability for peer effects in the setting of a simple production task. In our experiment, participants in the role of workers engage in a team real-effort task. We vary whether they can observe, or be observed by, one of their co-workers. In contrast to earlier findings from the field, we find no evidence that low-productivity workers perform better when they are observed by high-productivity co-workers. Instead, our results imply that peer effects in our experiment are heterogeneous, with some workers reciprocating a high-productivity co-worker but others taking the opportunity to free ride. PMID:29408863

METHODS DEVELOPMENT AT THE NEAR LAB ECOLOGICAL RESEARCH AREA (NLERA) LOCATED IN THE NEUSE RIVER BASIN.

EPA Science Inventory

This task supports the Agency's efforts on developing a proper risk assessment tools to address Ecological and eventually Human exposures. The Agency needs to be able to identify, measure and estimate ecosystem exposure to multiple stressors. The research under this task suppor...

Why do lab-scale experiments ever resemble geological scale patterning?

NASA Astrophysics Data System (ADS)

Ferdowsi, Behrooz; Jones, Brandon C.; Stein, Jeremy L.; Shinbrot, Troy

2017-11-01

The Earth and other planets are abundant with curious and poorly understood surface patterns. Examples include sand dunes, periodic and aperiodic ridges and valleys, and networks of river and submarine channels. We make the minimalist proposition that the dominant mechanism governing these varied patterns is mass conservation: notwithstanding detailed particulars, the universal rule is mass conservation and there are only a finite number of surface patterns that can result from this process. To test this minimalist proposition, we perform experiments in a vertically vibrated bed of fine grains, and we show that every one of a wide variety of patterns seen in the laboratory is also seen in recorded geomorphologies. We explore a range of experimental driving frequencies and amplitudes, and we complement these experimental results with a non-local cellular automata model that reproduces the surface patterns seen using a minimalist approach that allows a free surface to deform subject to mass conservation and simple known forces such as gravity. These results suggest a common cause for the effectiveness of lab-scale models for geological scale patterning that otherwise ought to have no reasonable correspondence.

Sensei: A Multi-Modal Framework for Assessing Stress Resiliency

DTIC Science & Technology

2013-02-01

Modal Framework for Assessing Stress Resiliency (February 1-28, 2013) From: Ajay Divakaran, Technical Leader Jeffrey Lubin, Senior Research...Progress and Accomplishments for Period 14 (February 2013): Task 3.1: Capture Behavioral Stress Markers in Real-Time in Lab Environment with...each data stream for each subject. In addition to these lab accomplishments, we also fine-tuned the timing of the Stroop /PDT presentations to

The Robotic Decathlon: Project-Based Learning Labs and Curriculum Design for an Introductory Robotics Course

ERIC Educational Resources Information Center

Cappelleri, D. J.; Vitoroulis, N.

2013-01-01

This paper presents a series of novel project-based learning labs for an introductory robotics course that are developed into a semester-long Robotic Decathlon. The last three events of the Robotic Decathlon are used as three final one-week-long project tasks; these replace a previous course project that was a semester-long robotics competition.…

From lab to full-scale ultrafiltration in microalgae harvesting

NASA Astrophysics Data System (ADS)

Wenten, I. G.; Steven, S.; Dwiputra, A.; Khoiruddin; Hakim, A. N.

2017-07-01

Ponding system is generally used for microalgae cultivation. However, selection of appropriate technology for the harvesting process is challenging due to the low cell density of cultivated microalgae from the ponding system and the large volume of water to be handled. One of the promising technologies for microalgae harvesting is ultrafiltration (UF). In this study, the performance of UF during harvesting of microalgae in a lab- and a full-scale test is investigated. The performances of both scales are compared and analyzed to provide an understanding of several aspects which affect the yield produced from lab and actual conditions. Furthermore, a unique self-standing non-modular UF is introduced in the full-scale test. The non-modular UF exhibits several advantages, such as simple piping and connection, single pump for filtration and backwashing, and smaller footprint. With those advantages, the non-modular UF could be a promising technology for microalgae harvesting in industrial-scale.

Role of accentuation in the selection/rejection task framing effect.

PubMed

Chen, Jing; Proctor, Robert W

2017-04-01

Procedure invariance is a basic assumption of rational theories of choice, however, it has been shown to be violated: Different response modes, or task frames, sometimes reveal opposite preferences. The current study focused on selection and rejection task frames, involving a unique type of problem with enriched and impoverished options, which has previously led to conflicting findings and theoretical explanations: the compatibility hypothesis (Shafir, 1993) and the accentuation hypothesis (Wedell, 1997). We examined the role of task frame by distinguishing these 2 hypotheses and evaluating the information-processing basis of the choices. Experiments conducted online (Experiments 1 and 3) and in-lab (Experiment 4 with eye-tracking technique) revealed a difference between the 2 task frames in the choice data (i.e., the task-framing effect) as a function of the relative attractiveness of the options. Also, this task-framing effect was not influenced by imposed time constraints (Experiments 5 and 6) and was similarly evident with a more direct measure for the option attractiveness (obtained in Experiment 7). Experiment 2, conducted in a lab setting with verbal-protocol requirements, yielded no task-framing effect, suggesting that a requirement to verbalize reasons for choice minimizes accentuation. With this exception, the choice data are in agreement with the accentuation hypothesis, and the combined findings in choice, decision time, task confusion, and eye-tracking data provide evidence of a basis in cognitive effort rather than motivation, as Wedell proposed. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Strategies to introduce Data Management techniques into the German university curriculum

NASA Astrophysics Data System (ADS)

Söding, E.; Fleischer, D.

2017-12-01

Data Management is high on the agenda of the German Research Organizations and Universities. While many organizations have committed to high level data management plans, these plans are often loosely binding and not followed adequately. As a consequence, few practical concepts are in place, implementing a sustainable reliable processing, archiving and publication of research data. While many institutions struggle with the organizational level, at which data management is implemented, Students are educated and time is lost, teaching them relevance, techniques and strategies in dealing in a thoughtful and ahead looking manner with their research data. Within a new research project we are tackling this problem in a two-fold way. 1. we are involving technical university personnel, who are working in labs, producing scientific data, in data management processes. This requires teaching, analysis of lab practices and the development of applications for support. 2. We are developing new teaching material, in order to introduce such DM strategies into regular practical courses conducted in such labs, by starting small scale experiments on long term time series. These can be analyzed by student within practical courses, and will demonstrate the practical use of DM practices in the courses. While the focus is on natural science labs, we also strive to create material for other disciplines using e.g. text analysis techniques, in particular in linguistics and history. By doing so, we are touching not only the traditional data-heavy disciplines, but try to bridge responsibility for this task over several disciplines and faculties, in order to raise broad acceptance and recognition in the whole university for the benefits of structured Data Management plans in projects.

Development of Predictive Models of Advanced Propulsion Concepts for Low Cost Space Transportation

NASA Technical Reports Server (NTRS)

Morrell, Michael Randy

2002-01-01

This final report presents the Graduate Student Research Program (GSRP) work Mr. Morrell was able to complete as a summer intern at NASA MSFS during the summer of 2001, and represents work completed from inception through project termination. The topics include: 1) NASA TD40 Organization; 2) Combustion Physics Lab; 3) Advanced Hydrocarbon Fuels; 4) GSRP Summer Tasks; 5) High Pressure Facility Installation; 6) High Pressure Combustion Issues; 7) High Energy Density Matter (HEDM) Hydrocarbons; and 8) GSRP Summer Intern Summary.

Performance assessment and calibration of a profiling lab-scale acoustic Doppler velocimeter for application over mixed sand-gravel beds

USDA-ARS?s Scientific Manuscript database

Acoustic Doppler velocimetry has made high-resolution turbulence measurements in sediment-laden flows possible. Recent developments have resulted in a commercially available lab-scale acoustic Doppler profiling device, a Nortek Vectrino II, that allows for three-dimensional velocity data to be colle...

Optimization of the inter-tablet coating uniformity for an active coating process at lab and pilot scale.

PubMed

Just, Sarah; Toschkoff, Gregor; Funke, Adrian; Djuric, Dejan; Scharrer, Georg; Khinast, Johannes; Knop, Klaus; Kleinebudde, Peter

2013-11-30

The objective of this study was to enhance the inter-tablet coating uniformity in an active coating process at lab and pilot scale by statistical design of experiments. The API candesartan cilexetil was applied onto gastrointestinal therapeutic systems containing the API nifedipine to obtain fixed dose combinations of these two drugs with different release profiles. At lab scale, the parameters pan load, pan speed, spray rate and number of spray nozzles were examined. At pilot scale, the parameters pan load, pan speed, spray rate, spray time, and spray pressure were investigated. A low spray rate and a high pan speed improved the coating uniformity at both scales. The number of spray nozzles was identified as the most influential variable at lab scale. With four spray nozzles, the highest CV value was equal to 6.4%, compared to 13.4% obtained with two spray nozzles. The lowest CV of 4.5% obtained with two spray nozzles was further reduced to 2.3% when using four spray nozzles. At pilot scale, CV values between 2.7% and 11.1% were achieved. Since the test of uniformity of dosage units accepts CV values of up to 6.25%, this active coating process is well suited to comply with the pharmacopoeial requirements. Copyright © 2013 Elsevier B.V. All rights reserved.

Stressor Effects in Lab and Life: Correspondences between the Effects of the Accident at Three Mile Island and Stress Responses in the Laboratory.

DTIC Science & Technology

1982-09-01

data as well as administra- tion requirements are available. Video game task: a non-social, task-oriented setting in which the person is working...dominant arm and the subject was instructed to watch a video screen. After the experimenter left the room, videotaped instructions for a video game (similar...with video games to understand the task. The task itself was selected for its general interest across divergent groups of potential subjects and

Reducing the language content in ToM tests: A developmental scale.

PubMed

Burnel, Morgane; Perrone-Bertolotti, Marcela; Reboul, Anne; Baciu, Monica; Durrleman, Stephanie

2018-02-01

The goal of the current study was to statistically evaluate the reliable scalability of a set of tasks designed to assess Theory of Mind (ToM) without language as a confounding variable. This tool might be useful to study ToM in populations where language is impaired or to study links between language and ToM. Low verbal versions of the ToM tasks proposed by Wellman and Liu (2004) for their scale were tested in 234 children (2.5 years to 11.9 years). Results showed that 5 of the tasks formed a scale according to both Guttman and Rasch models whereas all 6 tasks could form a scale according to the Rasch model only. The main difference from the original scale was that the Explicit False Belief task could be included whereas the Knowledge Access (KA) task could not. The authors argue that the more verbal version of the KA task administered in previous studies could have measured language understanding rather than ToM. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Evaluation and analysis of the orbital maneuvering vehicle video system

NASA Technical Reports Server (NTRS)

Moorhead, Robert J., II

1989-01-01

The work accomplished in the summer of 1989 in association with the NASA/ASEE Summer Faculty Research Fellowship Program at Marshall Space Flight Center is summarized. The task involved study of the Orbital Maneuvering Vehicle (OMV) Video Compression Scheme. This included such activities as reviewing the expected scenes to be compressed by the flight vehicle, learning the error characteristics of the communication channel, monitoring the CLASS tests, and assisting in development of test procedures and interface hardware for the bit error rate lab being developed at MSFC to test the VCU/VRU. Numerous comments and suggestions were made during the course of the fellowship period regarding the design and testing of the OMV Video System. Unfortunately from a technical point of view, the program appears at this point in time to be trouble from an expense prospective and is in fact in danger of being scaled back, if not cancelled altogether. This makes technical improvements prohibitive and cost-reduction measures necessary. Fortunately some cost-reduction possibilities and some significant technical improvements that should cost very little were identified.

Gordon Research Conferences on Polymers(W).

DTIC Science & Technology

1985-04-06

Robert B-303 Silberman, Ruth B-204 Ford Motor Company State Univ. of N.Y. Research Staff Dept. of Chemistry Science Lab. S-3049 223 Baker Lab. Dearborn...Fundamental Relation between the Breadth of R. Rendell the Relaxation Spectrum and Relaxation Time Naval Research Lab Scale: Application to Volume and

Research Extension and Education Programs on Bio-based Energy Technologies and Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jackson, Sam; Harper, David; Womac, Al

2010-03-02

The overall objectives of this project were to provide enhanced educational resources for the general public, educational and development opportunities for University faculty in the Southeast region, and enhance research knowledge concerning biomass preprocessing and deconstruction. All of these efforts combine to create a research and education program that enhances the biomass-based industries of the United States. This work was broken into five primary objective areas: • Task A - Technical research in the area of biomass preprocessing, analysis, and evaluation. • Tasks B&C - Technical research in the areas of Fluidized Beds for the Chemical Modification of Lignocellulosic Biomassmore » and Biomass Deconstruction and Evaluation. • Task D - Analyses for the non-scientific community to provides a comprehensive analysis of the current state of biomass supply, demand, technologies, markets and policies; identify a set of feasible alternative paths for biomass industry development and quantify the impacts associated with alternative path. • Task E - Efforts to build research capacity and develop partnerships through faculty fellowships with DOE national labs The research and education programs conducted through this grant have led to three primary results. They include: • A better knowledge base related to and understanding of biomass deconstruction, through both mechanical size reduction and chemical processing • A better source of information related to biomass, bioenergy, and bioproducts for researchers and general public users through the BioWeb system. • Stronger research ties between land-grant universities and DOE National Labs through the faculty fellowship program. In addition to the scientific knowledge and resources developed, funding through this program produced a minimum of eleven (11) scientific publications and contributed to the research behind at least one patent.« less

Towards a Metadata Schema for Characterizing Lesson Plans Supported by Virtual and Remote Labs in School Science Education

ERIC Educational Resources Information Center

Zervas, Panagiotis; Tsourlidaki, Eleftheria; Sotiriou, Sofoklis; Sampson, Demetrios G.

2015-01-01

Technological advancements in the field of World Wide Web have led to a plethora of remote and virtual labs (RVLs) that are currently available online and they are offered with or without cost. However, using a RVL to teach a specific science subject might not be a straightforward task for a science teacher. As a result, science teachers need to…

Lab-on-a-chip modules for detection of highly pathogenic bacteria: from sample preparation to detection

NASA Astrophysics Data System (ADS)

Julich, S.; Kopinč, R.; Hlawatsch, N.; Moche, C.; Lapanje, A.; Gärtner, C.; Tomaso, H.

2014-05-01

Lab-on-a-chip systems are innovative tools for the detection and identification of microbial pathogens in human and veterinary medicine. The major advantages are small sample volume and a compact design. Several fluidic modules have been developed to transform analytical procedures into miniaturized scale including sampling, sample preparation, target enrichment, and detection procedures. We present evaluation data for single modules that will be integrated in a chip system for the detection of pathogens. A microfluidic chip for purification of nucleic acids was established for cell lysis using magnetic beads. This assay was evaluated with spiked environmental aerosol and swab samples. Bacillus thuringiensis was used as simulant for Bacillus anthracis, which is closely related but non-pathogenic for humans. Stationary PCR and a flow-through PCR chip module were investigated for specific detection of six highly pathogenic bacteria. The conventional PCR assays could be transferred into miniaturized scale using the same temperature/time profile. We could demonstrate that the microfluidic chip modules are suitable for the respective purposes and are promising tools for the detection of bacterial pathogens. Future developments will focus on the integration of these separate modules to an entire lab-on-a-chip system.

IMPACT: Imaging and Molecular Markers for Patients with Lung Cancer: Approaches with Molecular Targets, Complementary/Innovative Treatments, and Therapeutic Modalities

DTIC Science & Technology

2016-04-01

Hypomagnesemia, Grade 3 in 1 patient • Hypokalemia, Grade 3 in 2 patient • Pneumonia , Grade 3 in 7 patients • Dehydration, Grade 3 in 3 patients. Once...improvements on lab- scale radiosynthesis (Fig. 9) so that it is readily scaled up and adopted by the cGMP manufacturing. We are working on an automated...reproducibly building at the nanometer scale , including the need for streamlined and “bottom-up” approaches for assembling nanoparticle architectures, the

Practicing urologist learning laparoscopy: no short cut to short cuts!

PubMed

Mahmud, Syed Mamun; Mishra, Shashikant; Desai, Mahesh Ramanlal

2011-05-01

To emphasize the importance of regular exercising in dry lab in initial phase of learning of laparoscopic surgery by a practicing urologist. The study was performed at Dry Lab -Jayaramdas Patel Academic Centre (JPAC) attached to Muljibhai Patel Urological Hospital, Nadiad, India. The study is based on 30 sets of exercises of four standard tasks utilized to learn Hand-Eye coordination for Laparoscopic Surgery. All sets were performed by a single participant over a period of 19 days and the exercise record was retrospectively analyzed. The participant had limited exposure of one year in a low volume laparoscopy center. Correlation between Exercise number and Task Completion Time (TCT) was calculated by Pearson's Correlation Coefficient and its significance is assessed by Student paired t test. The current study describes 30 exercises of 4 standard tasks for hand-eye-coordination. Although the study was completed in 19 days but there were two intervals which point to the objective of this study. First interval was of 3 days and it occurred after 4th exercise. At 5th exercise the Task Completion Time started rising more than the 2nd exercise. This regression further worsened on 6th exercise which had an interval of 2 days. Here the (TCT) went up almost equal to 1st exercise (1050 vs 1054 seconds). Mean time for IT1, IT2, IT3, IT4 and TCT of over all exercises were calculated as 24.2 +/- 3.7, 121.9 +/- 54.9, 233 +/- 73.5, 199 +/- 55.1 and 582.5 +/- 174.8 seconds respectively. Significant correlation was noticed between number of exercises performed and improvement in time taken for individual tasks (IT 2 to IT4) and TCT. However there was no significant impact on Task 1. Regular Dry Lab exercises improves hand eye coordination and psychomotor skill dedicated continuous exercising has significant impact in reducing TCT.

Toward Better Physics Labs for Future Biologists

NASA Astrophysics Data System (ADS)

Giannini, John; Moore, Kim; Losert, Wolfgang

2014-03-01

We have developed a set of laboratories and hands on activities to accompany a new two-semester interdisciplinary physics course that has been successfully developed and tested in two small test classes of students at the University of Maryland, College Park (UMD) in 2012-2013, and is currently being used on a wider scale. We have designed the laboratories to be taken accompanying a reformed course in the student's second year, with calculus, biology, and chemistry as prerequisites. This permits the laboratories to include significant content on physics relevant to cellular scales, from chemical interactions to random motion and charge screening in fluids. One major focus of the laboratories is to introduce the students to research-grade equipment and modern physics analysis tools in contexts relevant to biology, while maintaining the pedagogically valuable open-ended laboratory structure of reformed laboratories. Lab development procedures along with some preliminary student results from these two small test classes are discussed.

NASA Scientific Data Purchase Project: From Collection to User

NASA Technical Reports Server (NTRS)

Nicholson, Lamar; Policelli, Fritz; Fletcher, Rose

2002-01-01

NASA's Scientific Data Purchase (SDP) project is currently a $70 million operation managed by the Earth Science Applications Directorate at Stennis Space Center. The SDP project was developed in 1997 to purchase scientific data from commercial sources for distribution to NASA Earth science researchers. Our current data holdings include 8TB of remote sensing imagery consisting of 18 products from 4 companies. Our anticipated data volume is 60 TB by 2004, and we will be receiving new data products from several additional companies. Our current system capacity is 24 TB, expandable to 89 TB. Operations include tasking of new data collections, archive ordering, shipment verification, data validation, distribution, metrics, finances, customer feedback, and technical support. The program has been included in the Stennis Space Center Commercial Remote Sensing ISO 9001 registration since its inception. Our operational system includes automatic quality control checks on data received (with MatLab analysis); internally developed, custom Web-based interfaces that tie into commercial-off-the-shelf software; and an integrated relational database that links and tracks all data through operations. We've distributed nearly 1500 datasets, and almost 18,000 data files have been downloaded from our public web site; on a 10-point scale, our customer satisfaction index is 8.32 at a 23% response level. More information about the SDP is available on our Web site.

Human perception testing methodology for evaluating EO/IR imaging systems

NASA Astrophysics Data System (ADS)

Graybeal, John J.; Monfort, Samuel S.; Du Bosq, Todd W.; Familoni, Babajide O.

2018-04-01

The U.S. Army's RDECOM CERDEC Night Vision and Electronic Sensors Directorate (NVESD) Perception Lab is tasked with supporting the development of sensor systems for the U.S. Army by evaluating human performance of emerging technologies. Typical research questions involve detection, recognition and identification as a function of range, blur, noise, spectral band, image processing techniques, image characteristics, and human factors. NVESD's Perception Lab provides an essential bridge between the physics of the imaging systems and the performance of the human operator. In addition to quantifying sensor performance, perception test results can also be used to generate models of human performance and to drive future sensor requirements. The Perception Lab seeks to develop and employ scientifically valid and efficient perception testing procedures within the practical constraints of Army research, including rapid development timelines for critical technologies, unique guidelines for ethical testing of Army personnel, and limited resources. The purpose of this paper is to describe NVESD Perception Lab capabilities, recent methodological improvements designed to align our methodology more closely with scientific best practice, and to discuss goals for future improvements and expanded capabilities. Specifically, we discuss modifying our methodology to improve training, to account for human fatigue, to improve assessments of human performance, and to increase experimental design consultation provided by research psychologists. Ultimately, this paper outlines a template for assessing human perception and overall system performance related to EO/IR imaging systems.

PHYLUCE is a software package for the analysis of conserved genomic loci.

PubMed

Faircloth, Brant C

2016-03-01

Targeted enrichment of conserved and ultraconserved genomic elements allows universal collection of phylogenomic data from hundreds of species at multiple time scales (<5 Ma to > 300 Ma). Prior to downstream inference, data from these types of targeted enrichment studies must undergo preprocessing to assemble contigs from sequence data; identify targeted, enriched loci from the off-target background data; align enriched contigs representing conserved loci to one another; and prepare and manipulate these alignments for subsequent phylogenomic inference. PHYLUCE is an efficient and easy-to-install software package that accomplishes these tasks across hundreds of taxa and thousands of enriched loci. PHYLUCE is written for Python 2.7. PHYLUCE is supported on OSX and Linux (RedHat/CentOS) operating systems. PHYLUCE source code is distributed under a BSD-style license from https://www.github.com/faircloth-lab/phyluce/ PHYLUCE is also available as a package (https://binstar.org/faircloth-lab/phyluce) for the Anaconda Python distribution that installs all dependencies, and users can request a PHYLUCE instance on iPlant Atmosphere (tag: phyluce). The software manual and a tutorial are available from http://phyluce.readthedocs.org/en/latest/ and test data are available from doi: 10.6084/m9.figshare.1284521. brant@faircloth-lab.org Supplementary data are available at Bioinformatics online. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Holodeck Testbed Project

NASA Technical Reports Server (NTRS)

Arias, Adriel (Inventor)

2016-01-01

The main objective of the Holodeck Testbed is to create a cost effective, realistic, and highly immersive environment that can be used to train astronauts, carry out engineering analysis, develop procedures, and support various operations tasks. Currently, the Holodeck testbed allows to step into a simulated ISS (International Space Station) and interact with objects; as well as, perform Extra Vehicular Activities (EVA) on the surface of the Moon or Mars. The Holodeck Testbed is using the products being developed in the Hybrid Reality Lab (HRL). The HRL is combining technologies related to merging physical models with photo-realistic visuals to create a realistic and highly immersive environment. The lab also investigates technologies and concepts that are needed to allow it to be integrated with other testbeds; such as, the gravity offload capability provided by the Active Response Gravity Offload System (ARGOS). My main two duties were to develop and animate models for use in the HRL environments and work on a new way to interface with computers using Brain Computer Interface (BCI) technology. On my first task, I was able to create precise computer virtual tool models (accurate down to the thousandths or hundredths of an inch). To make these tools even more realistic, I produced animations for these tools so they would have the same mechanical features as the tools in real life. The computer models were also used to create 3D printed replicas that will be outfitted with tracking sensors. The sensor will allow the 3D printed models to align precisely with the computer models in the physical world and provide people with haptic/tactile feedback while wearing a VR (Virtual Reality) headset and interacting with the tools. Getting close to the end of my internship the lab bought a professional grade 3D Scanner. With this, I was able to replicate more intricate tools at a much more time-effective rate. The second task was to investigate the use of BCI to control objects inside the hybrid reality ISS environment. This task looked at using an Electroencephalogram (EEG) headset to collect brain state data that could be mapped to commands that a computer could execute. On this Task, I had a setback with the hardware, which stopped working and was returned to the vendor for repair. However, I was still able to collect some data, was able to process it, and started to create correlation algorithms between the electrical patterns in the brain and the commands we wanted the computer to carry out. I also carried out a test to investigate the comfort of the headset if it is worn for a long time. The knowledge gained will benefit me in my future career. I learned how to use various modeling and programming tools that included Blender, Maya, Substance Painter, Artec Studio, Github, and Unreal Engine 4. I learned how to use a professional grade 3D scanner and 3D printer. On the BCI Project I learned about data mining and how to create correlation algorithms. I also supported various demos including a live demo of the hybrid reality lab capabilities at ComicPalooza. This internship has given me a good look into engineering at NASA. I developed a more thorough understanding of engineering and my overall confidence has grown. I have also realized that any problem can be fixed, if you try hard enough, and as an engineer it is your job to not only fix problems but to embrace coming up with solutions to those problems.

An analysis of high school students' perceptions and academic performance in laboratory experiences

NASA Astrophysics Data System (ADS)

Mirchin, Robert Douglas

This research study is an investigation of student-laboratory (i.e., lab) learning based on students' perceptions of experiences using questionnaire data and evidence of their science-laboratory performance based on paper-and-pencil assessments using Maryland-mandated criteria, Montgomery County Public Schools (MCPS) criteria, and published laboratory questions. A 20-item questionnaire consisting of 18 Likert-scale items and 2 open-ended items that addressed what students liked most and least about lab was administered to students before labs were observed. A pre-test and post-test assessing laboratory achievement were administered before and after the laboratory experiences. The three labs observed were: soda distillation, stoichiometry, and separation of a mixture. Five significant results or correlations were found. For soda distillation, there were two positive correlations. Student preference for analyzing data was positively correlated with achievement on the data analysis dimension of the lab rubric. A student preference for using numbers and graphs to analyze data was positively correlated with achievement on the analysis dimension of the lab rubric. For the separating a mixture lab data the following pairs of correlations were significant. Student preference for doing chemistry labs where numbers and graphs were used to analyze data had a positive correlation with writing a correctly worded hypothesis. Student responses that lab experiences help them learn science positively correlated with achievement on the data dimension of the lab rubric. The only negative correlation found related to the first result where students' preference for computers was inversely correlated to their performance on analyzing data on their lab report. Other findings included the following: students like actual experimental work most and the write-up and analysis of a lab the least. It is recommended that lab science instruction be inquiry-based, hands-on, and that students be tested for lab content acquisition. The final conclusion of the study is that students expressed a preference for working in groups and working with materials and equipment as opposed to individual, non-group work and analyzing data.

Berkeley Lab - Materials Sciences Division

Science.gov Websites

Synthesis Condensed Matter and Materials Physics Scattering and Instrumentation Science Centers Center for materials and phenomena at multiple time and length scales. Through our core programs and research centers Berkeley Lab Berkeley Lab A-Z Index Phone Book Jobs Search DOE Search MSD Go MSD - Materials

iMetaLab 1.0: A web platform for metaproteomics data analysis.

PubMed

Liao, Bo; Ning, Zhibin; Cheng, Kai; Zhang, Xu; Li, Leyuan; Mayne, Janice; Figeys, Daniel

2018-06-15

The human gut microbiota, a complex, dynamic and biodiverse community, has been increasingly shown to influence many aspects of health and disease. Metaproteomic analysis has proven to be a powerful approach to study the functionality of the microbiota. However, the processing and analyses of metaproteomic mass spectrometry (MS) data remains a daunting task in metaproteomics data analysis. We developed iMetaLab, a web based platform to provide a user-friendly and comprehensive data analysis pipeline with a focus on lowering the technical barrier for metaproteomics data analysis. iMetaLab is freely available through at http://imetalab.ca. Supplementary data are available at Bioinformatics online.

RANS Simulation (Virtual Blade Model [VBM]) of Array of Three Coaxial Lab Scaled DOE RM1 MHK Turbine with 5D Spacing

DOE Data Explorer

Javaherchi, Teymour

2016-06-08

Attached are the .cas and .dat files along with the required User Defined Functions (UDFs) and look-up table of lift and drag coefficients for the Reynolds Averaged Navier-Stokes (RANS) simulation of three coaxially located lab-scaled DOE RM1 turbine implemented in ANSYS FLUENT CFD-package. The lab-scaled DOE RM1 is a re-design geometry, based of the full scale DOE RM1 design, producing same power output as the full scale model, while operating at matched Tip Speed Ratio values at reachable laboratory Reynolds number (see attached paper). In this case study the flow field around and in the wake of the lab-scaled DOE RM1 turbines in a coaxial array is simulated using Blade Element Model (a.k.a Virtual Blade Model) by solving RANS equations coupled with k-\\omega turbulence closure model. It should be highlighted that in this simulation the actual geometry of the rotor blade is not modeled. The effect of turbine rotating blades are modeled using the Blade Element Theory. This simulation provides an accurate estimate for the performance of each device and structure of their turbulent far wake. The results of these simulations were validated against the developed in-house experimental data. Simulations for other turbine configurations are available upon request.

Application of Fresnel Zone to Cross Talk

NASA Technical Reports Server (NTRS)

Javan, Hank

1998-01-01

Unintentional radiation results in cross coupling to nearby cables. As frequency increases, the amount of this coupling becomes significant especially in high speed data transmission and space lab experiments. There has been a considerable amount of research to model this radiation and design the electronic equipment accordingly so that operation of space lab instruments will be immune to unwanted radiation. Here at MSFC, the Electromagnetics and Aerospace Environment Branch has the responsibility to analyze, test, and make the necessary recommendation as to the safe operation of instruments used in the space program. Rules, regulation, and limits as set by this group are published in Electromagnetic Compatibility Design and Interference Control (MEDIC) Handbook. This document contains both conducted and radiate emission rules and limits are set by NASA. However cross coupling have not been included. At the time of assigning the research task for the author, the Group decided that a more in-depth investigation of Near Field is needed before establishing a set of rules and limits for cross coupling. Thus this task was assigned to the author with hope that his work will be more beneficial to NASA's Space mission experiments. The model and the method which will be described shortly is intended to improve the present approach of this Group and suggests a method for measuring the cross field coupling capacitance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swapan Chattopadhyay

Hurricane Isabel was at category five--the most violent on the Saffir-Simpson scale of hurricane strength--when it began threatening the central Atlantic seaboard of the US. Over the course of several days, precautions against the extreme weather conditions were taken across the Jefferson Lab site in south-east Virginia. On 18 September 2003, when Isabel struck North Carolina's Outer Banks and moved northward, directly across the region around the laboratory, the storm was still quite destructive, albeit considerably reduced in strength. The flood surge and trees felled by wind substantially damaged or even devastated buildings and homes, including many belonging to Jeffersonmore » Lab staff members. For the laboratory itself, Isabel delivered an unplanned and severe challenge in another form: a power outage that lasted nearly three-and-a-half days, and which severely tested the robustness of Jefferson Lab's two superconducting machines, the Continuous Electron Beam Accelerator Facility (CEBAF) and the superconducting radiofrequency ''driver'' accelerator of the laboratory's free-electron laser. Robustness matters greatly for science at a time when microwave superconducting linear accelerators (linacs) are not only being considered, but in some cases already being built for projects such as neutron sources, rare-isotope accelerators, innovative light sources and TeV-scale electron-positron linear colliders. Hurricane Isabel interrupted a several-week-long maintenance shutdown of CEBAF, which serves nuclear and particle physics and represents the world's pioneering large-scale implementation of superconducting radiofrequency (SRF) technology. The racetrack-shaped machine is actually a pair of 500-600 MeV SRF linacs interconnected by recirculation arc beamlines. CEBAF delivers simultaneous beams at up to 6 GeV to three experimental halls. An imminent upgrade will double the energy to 12 GeV and add an extra hall for ''quark confinement'' studies. On a smaller scale, Jefferson Lab's original kilowatt-scale infrared free-electron laser (FEL) is ''driven'' by a high-current cousin of CEBAF, a 70 MeV SRF linac with a high-current injector. The FEL serves multidisciplinary science and technology as the world's highest-average-power source of tunable coherent infrared light. An upgrade to 10 kW is in commissioning--as it was when Isabel began threatening.« less

Transfer of tracers and pesticides in lab scale wetland systems: the role of vegetation

NASA Astrophysics Data System (ADS)

Durst, R.; Imfeld, G.; Lange, J.

2012-04-01

Surface wetlands can collect contaminated runoff from urban or agricultural catchments and have intrinsic physical, chemical and biological retention and removal processes useful for mitigating contaminants, including pesticides, and thus limiting the contamination of aquatic ecosystems. Yet little is known about the transfer of pesticides between wetlands collecting pesticides runoff and groundwater, and the subsequent threat of groundwater contamination. In particular, the influence of wetland vegetation and related processes during pesticide transfer is largely unknown. Here we evaluate the transfer of the widely used herbicide Isoproturon (IPU) and the fungicide Metalaxyl (MTX) with that of Uranine (UR) and Sulphorhodamine (SRB) in a vegetated and a non-vegetated lab-scale wetland. UR and SRB had successfully served as a reference for pesticides in surface wetlands. We filled two 65 cm long and 15 cm diameter borosilicate columns with sediment cores from a wetland, one without and one with vegetation (Phragmites australis, Cav.). When a constant flow-through rate of 0.33 ml min-1 was reached, tracers and pesticides were injected simultaneously and continuously. The hydrological mass balance and tracer concentrations were measured daily at the outlet of the lab-scale wetland. Samples for pesticides and hydrochemical analyses were collected biweekly. The lab-scale wetlands were covered to limit evaporation and light decay of injected compounds. The reactive transfer of compounds in the vegetated and non-vegetated lab-scale wetland was compared based on breakthrough curves (BTC's) and model parameters of the lumped parameter model CXTFIT. The hydrologic balance revealed that the intensity of transpiration and hence plant activity in the lab-scale wetlands progressively decreased and then apparently ceased after about eight days following continuous pesticide injection. In this first phase, no significant difference in the hydrologic balances could be observed between the vegetated and the non-vegetated column. In a second phase, vegetation transpiration progressively increased, as inferred from lower volumes of effluent water in the vegetated system. Overall, the behavior of pesticides and tracers, as inferred from the BTC's, were similar. This suggests that fluorescent tracers may be used as a reference for pesticides when studying the surface-groundwater interface. Both pesticides and tracers showed larger recovery rates (UR: 81.7 to 78.6%; SRB: 65.6 to 55.9%; IPU: 76.6 to 79.7%; MTX: 39.5 to 37.5%) and lower retention in the vegetated system. We attribute this finding to preferential flow paths along plant roots. Overall, our study suggests that wetland vegetation and rhizosheric processes may have a dual role in wetland pollutant transfer: while wetland vegetation may enhance retention and bio-degradation of contaminants in surface water, it may also generate preferential flow paths and hence facilitate pollutant transfer to groundwater. Acknowledgment: This study has been funded by the European Union (INTERREG) in the framework of the PhytoRet Project.

From big data analysis in the cloud to robotic pot drumming: tales from the Met Office Informatics Lab

NASA Astrophysics Data System (ADS)

Robinson, Niall; Tomlinson, Jacob; Prudden, Rachel; Hilson, Alex; Arribas, Alberto

2017-04-01

The Met Office Informatics Lab is a small multidisciplinary team which sits between science, technology and design. Our mission is simply "to make Met Office data useful" - a deliberately broad objective. Our prototypes often trial cutting edge technologies, and so far have included projects such as virtual reality data visualisation in the web browser, bots and natural language interfaces, and artificially intelligent weather warnings. In this talk we focus on our latest project, Jade, a big data analysis platform in the cloud. It is a powerful, flexible and simple to use implementation which makes extensive use of technologies such as Jupyter, Dask, containerisation, Infrastructure as Code, and auto-scaling. Crucially, Jade is flexible enough to be used for a diverse set of applications: it can present weather forecast information to meteorologists and allow climate scientists to analyse big data sets, but it is also effective for analysing non-geospatial data. As well as making data useful, the Informatics Lab also trials new working practises. In this presentation, we will talk about our experience of making a group like the Lab successful.

Novel Surface Modification Method for Ultrasupercritical Coal-Fired Boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, T. Danny

2013-05-22

US Department of Energy seeks an innovative coating technology for energy production to reduce the emission of SOx, NOx, and CO2 toxic gaseous species. To realize this need, Inframat Corporation (IMC) proposed an SPS thermal spray coating technique to produce ultrafine/nanocoatings that can be deposited onto the surfaces of high temperature boiler tubes, so that higher temperatures of boiler operation becomes possible, leading to significantly reduced emission of toxic gaseous species. It should be noted that the original PI was Dr. Xinqing Ma, who after 1.5 year conducting this project left Inframat in December, 2008. Thus, the PI was transferredmore » to Dr. Danny Xiao, who originally co-authored the proposal with Dr. Ma, in order to carry the project into a completion. Phase II Objectives: The proposed technology has the following attributes, including: (1). Dispersion of a nanoparticle or alloyed particle in a solvent to form a uniform slurry feedstock; (2). Feeding of the slurry feedstock into a thermal spray flame, followed by deposition of the slurry feedstock onto substrates to form tenacious nanocoatings; (3). High coating performance: including high bonding strength, and high temperature service life in the temperature range of 760oC/1400oF. Following the above premises, our past Phase I project has demonstrated the feasibility in small scale coatings on boiler substrates. The objective of this Phase II project was to focus on scale-up the already demonstrated Phase I work for the fabrication of SPS coatings that can satisfy DOE's emission reduction goals for energy production operations. Specifically, they are: (1). Solving engineering problems to scale-up the SPS-HVOF delivery system to a prototype production sub-delivery system; (2). Produce ultrafine/nanocoatings using the scale-up prototype system; (3). Demonstrate the coated components using the scale-up device having superior properties. Proposed Phase II Tasks: In the original Phase II proposal, we have six (6) technical tasks plus one (1) reporting task, as described below: Task 1 Scale-up and optimize the SPS process; Task 2 Coating design and fabrication with desired microstructure; Task 3 Evaluate microstructure and physical properties; Task 4 Test performance of long-term corrosion and erosion; Task 5 Test mechanical property and reliability; Task 6 Coating of a prototype boiler tube for evaluation; Task 7 Reporting task. To date, we have already completed all the technical tasks of 1 through 6. Major Phase II Achievements: In this four (4) year working period, Inframat had spent great effort to complete the proposed tasks. The project had been completed; the goals have been accomplished. Major achievements obtained include: (1). Developed a prototype scale-up slurry feedstock delivery system for thermal spray coatings; (2). Successfully coated high performance coatings using this scale-up slurry delivery system; (3). Commercial applications in energy efficiency and clean energy components have been developed using this newly fabricated slurry feedstock delivery system.« less

Task Design for Intercultural Telecollaboration in Secondary Schools: Insights from the EU project TILA

ERIC Educational Resources Information Center

Hoffstaedter, Petra; Kohn, Kurt

2014-01-01

Our contribution focuses on synchronous oral telecollaboration in secondary schools. With reference to the EU project TILA, aspects of task design and implementation are discussed against the backdrop of issues of technological quality in connection with class organisation in computer labs. Case study evidence is provided in favour of the…

A New Approach to Standardize Multicenter Studies: Mobile Lab Technology for the German Environmental Specimen Bank

PubMed Central

Lermen, Dominik; Schmitt, Daniel; Bartel-Steinbach, Martina; Schröter-Kermani, Christa; Kolossa-Gehring, Marike; von Briesen, Hagen; Zimmermann, Heiko

2014-01-01

Technical progress has simplified tasks in lab diagnosis and improved quality of test results. Errors occurring during the pre-analytical phase have more negative impact on the quality of test results than errors encountered during the total analytical process. Different infrastructures of sampling sites can highly influence the quality of samples and therewith of analytical results. Annually the German Environmental Specimen Bank (ESB) collects, characterizes, and stores blood, plasma, and urine samples of 120–150 volunteers each on four different sampling sites in Germany. Overarching goal is to investigate the exposure to environmental pollutants of non-occupational exposed young adults combining human biomonitoring with questionnaire data. We investigated the requirements of the study and the possibility to realize a highly standardized sampling procedure on a mobile platform in order to increase the required quality of the pre-analytical phase. The results lead to the development of a mobile epidemiologic laboratory (epiLab) in the project “Labor der Zukunft” (future’s lab technology). This laboratory includes a 14.7 m2 reception area to record medical history and exposure-relevant behavior, a 21.1 m2 examination room to record dental fillings and for blood withdrawal, a 15.5 m2 biological safety level 2 laboratory to process and analyze samples on site including a 2.8 m2 personnel lock and a 3.6 m2 cryofacility to immediately freeze samples. Frozen samples can be transferred to their final destination within the vehicle without breaking the cold chain. To our knowledge, we herewith describe for the first time the implementation of a biological safety laboratory (BSL) 2 lab and an epidemiologic unit on a single mobile platform. Since 2013 we have been collecting up to 15.000 individual human samples annually under highly standardized conditions using the mobile laboratory. Characterized and free of alterations they are kept ready for retrospective analyses in their final archive, the German ESB. PMID:25141120

A new approach to standardize multicenter studies: mobile lab technology for the German Environmental Specimen Bank.

PubMed

Lermen, Dominik; Schmitt, Daniel; Bartel-Steinbach, Martina; Schröter-Kermani, Christa; Kolossa-Gehring, Marike; von Briesen, Hagen; Zimmermann, Heiko

2014-01-01

Technical progress has simplified tasks in lab diagnosis and improved quality of test results. Errors occurring during the pre-analytical phase have more negative impact on the quality of test results than errors encountered during the total analytical process. Different infrastructures of sampling sites can highly influence the quality of samples and therewith of analytical results. Annually the German Environmental Specimen Bank (ESB) collects, characterizes, and stores blood, plasma, and urine samples of 120-150 volunteers each on four different sampling sites in Germany. Overarching goal is to investigate the exposure to environmental pollutants of non-occupational exposed young adults combining human biomonitoring with questionnaire data. We investigated the requirements of the study and the possibility to realize a highly standardized sampling procedure on a mobile platform in order to increase the required quality of the pre-analytical phase. The results lead to the development of a mobile epidemiologic laboratory (epiLab) in the project "Labor der Zukunft" (future's lab technology). This laboratory includes a 14.7 m(2) reception area to record medical history and exposure-relevant behavior, a 21.1 m(2) examination room to record dental fillings and for blood withdrawal, a 15.5 m(2) biological safety level 2 laboratory to process and analyze samples on site including a 2.8 m(2) personnel lock and a 3.6 m2 cryofacility to immediately freeze samples. Frozen samples can be transferred to their final destination within the vehicle without breaking the cold chain. To our knowledge, we herewith describe for the first time the implementation of a biological safety laboratory (BSL) 2 lab and an epidemiologic unit on a single mobile platform. Since 2013 we have been collecting up to 15.000 individual human samples annually under highly standardized conditions using the mobile laboratory. Characterized and free of alterations they are kept ready for retrospective analyses in their final archive, the German ESB.

A study of energy-size relationship and wear rate in a lab-scale high pressure grinding rolls unit

NASA Astrophysics Data System (ADS)

Rashidi Dashtbayaz, Samira

This study is focused on two independent topics of energy-size relationship and wear-rate measurements on a lab-scale high pressure grinding rolls (HPGR). The first part of this study has been aimed to investigate the influence of the operating parameters and the feed characteristics on the particle-bed breakage using four different ore samples in a 200 mm x 100 mm lab-scale HPGR. Additionally, multistage grinding, scale-up from a lab-scale HPGR, and prediction of the particle size distributions have been studied in detail. The results obtained from energy-size relationship studies help with better understanding of the factors contributing to more energy-efficient grinding. It will be shown that the energy efficiency of the two configurations of locked-cycle and open multipass is completely dependent on the ore properties. A test procedure to produce the scale-up data is presented. The comparison of the scale-up factors between the data obtained on the University of Utah lab-scale HPGR and the industrial machine at the Newmont Boddington plant confirmed the applicability of lab-scale machines for trade-off studies. The population balance model for the simulation of product size distributions has shown to work well with the breakage function estimated through tests performed on the HPGR at high rotational speed. Selection function has been estimated by back calculation of population balance model with the help of the experimental data. This is considered to be a major step towards advancing current research on the simulation of particle size distribution by using the HPGR machine for determining the breakage function. Developing a technique/setup to measure the wear rate of the HPGR rolls' surface is the objective of the second topic of this dissertation. A mockup was initially designed to assess the application of the linear displacement sensors for measuring the rolls' weight loss. Upon the analysis of that technique and considering the corresponding sources of errors, the application of the 2D distance measurement sensors was studied to directly determine the wear rate on the lab-sale HPGR roll. Results obtained from various grinding tests revealed that the operating variations were beyond the expected wear rate. Based on the valuable outcomes from the two mentioned experimental designs, a cup-disc arrangement similar to piston-die apparatus was developed to indirectly measure the wear rate on the HPGR roll. The preliminary outputs proved to be promising for further investigation into the development of this method in order to relate the measured data on the cup-disc apparatus to the actual wear rate on the HPGR rolls.

Guide to Using Sierra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, Ryan Phillip; Agelastos, Anthony Michael; Miller, Joel D.

2015-03-01

Sierra is an engineering mechanics simulation code suite supporting the Nation's Nuclear Weapons mission as well as other customers. It has explicit ties to Sandia National Labs' workfow, including geometry and meshing, design and optimization, and visualization. Dis- tinguishing strengths include "application aware" development, scalability, SQA and V&V, multiple scales, and multi-physics coupling. This document is intended to help new and existing users of Sierra as a user manual and troubleshooting guide.

Guide to Using Sierra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, Ryan Phillip; Agelastos, Anthony Michael; Miller, Joel D.

2017-04-01

Sierra is an engineering mechanics simulation code suite supporting the Nation's Nuclear Weapons mission as well as other customers. It has explicit ties to Sandia National Labs' workfow, including geometry and meshing, design and optimization, and visualization. Dis- tinguishing strengths include "application aware" development, scalability, SQA and V&V, multiple scales, and multi-physics coupling. This document is intended to help new and existing users of Sierra as a user manual and troubleshooting guide.

Formulation design of taste-masked particles, including famotidine, for an oral fast-disintegrating dosage form.

PubMed

Mizumoto, Takao; Tamura, Tetsuya; Kawai, Hitoshi; Kajiyama, Atsushi; Itai, Shigeru

2008-04-01

In this study, the taste-masking of famotidine, which could apply to any fast-disintegrating tablet, was investigated using the spray-dry method. The target characteristics of taste-masked particles were set as follows: the dissolution rate is not to be more than 30% at 1 min and not less than 85% at 15 min, and the particle size is not to be more than 150 microm in diameter to avoid a gritty feeling in the mouth. The target dissolution profiles of spray-dried particles consisting of Aquacoat ECD30 and Eudragit NE30D or triacetin was accomplished by the screening of formulas and the appropriate lab-scale manufacturing conditions. Lab-scale testing produced taste-masked particles that met the formulation targets. On the pilot scale, spray-dried particles with attributes, such as dissolution rate and particle size, of the same quality were produced, and reproducibility was also confirmed. This confirmed that the spray-dry method produced the most appropriate taste-masked particles for fast-disintegrating dosage forms.

eComLab: remote laboratory platform

NASA Astrophysics Data System (ADS)

Pontual, Murillo; Melkonyan, Arsen; Gampe, Andreas; Huang, Grant; Akopian, David

2011-06-01

Hands-on experiments with electronic devices have been recognized as an important element in the field of engineering to help students get familiar with theoretical concepts and practical tasks. The continuing increase the student number, costly laboratory equipment, and laboratory maintenance slow down the physical lab efficiency. As information technology continues to evolve, the Internet has become a common media in modern education. Internetbased remote laboratory can solve a lot of restrictions, providing hands-on training as they can be flexible in time and the same equipment can be shared between different students. This article describes an on-going remote hands-on experimental radio modulation, network and mobile applications lab project "eComLab". Its main component is a remote laboratory infrastructure and server management system featuring various online media familiar with modern students, such as chat rooms and video streaming.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hansen, Timothy M.; Palmintier, Bryan; Suryanarayanan, Siddharth

As more Smart Grid technologies (e.g., distributed photovoltaic, spatially distributed electric vehicle charging) are integrated into distribution grids, static distribution simulations are no longer sufficient for performing modeling and analysis. GridLAB-D is an agent-based distribution system simulation environment that allows fine-grained end-user models, including geospatial and network topology detail. A problem exists in that, without outside intervention, once the GridLAB-D simulation begins execution, it will run to completion without allowing the real-time interaction of Smart Grid controls, such as home energy management systems and aggregator control. We address this lack of runtime interaction by designing a flexible communication interface, Bus.pymore » (pronounced bus-dot-pie), that uses Python to pass messages between one or more GridLAB-D instances and a Smart Grid simulator. This work describes the design and implementation of Bus.py, discusses its usefulness in terms of some Smart Grid scenarios, and provides an example of an aggregator-based residential demand response system interacting with GridLAB-D through Bus.py. The small scale example demonstrates the validity of the interface and shows that an aggregator using said interface is able to control residential loads in GridLAB-D during runtime to cause a reduction in the peak load on the distribution system in (a) peak reduction and (b) time-of-use pricing cases.« less

Migration of Hazardous Substances through Soil. Part 4. Development of a Serial Batch Extraction Method and Application to the Accelerated Testing of Seven Industrial Wastes

DTIC Science & Technology

1987-09-01

Evaluation Commnand &_. ADMASS Coly, 1W~., and ZIP Code ) 7b. ADDRESS (C01y, State, wid ZIP Code ) Dugwiay, Utahi 84022-5000 Aberdeen Proving Ground...Aency_________________________ 9L AoOMS(CRY, 0to, and ZIP Code ) 10. SOURCE OF FUNDING NUMBERS Hazardous Waste Environmental RLsearch Lab PROGRAM PROJECT TASK...CLASSIFICATION 0 UNO.ASSIFIEDAIJNLIMITED 0l SAME AS RPT. 03 OTIC USERS UNCLA.SSIFIED 22a. RAWE OF RESPONSIBLE INDIVIDUAL 22b TELEPHONE (Include Area Code ) I

Kennedy's Biomedical Laboratory Makes Multi-Tasking Look Easy

NASA Technical Reports Server (NTRS)

Dunn, Carol Anne

2009-01-01

If it is one thing that Florida has in abundance, it is sunshine and with that sunshine heat and humidity. For workers at the Kennedy Space Center that have to work outside in the heat and humidity, heat exhaustion/stroke is a real possibility. It might help people to know that Kennedy's Biomedical Laboratory has been testing some new Koolvests(Trademark) that can be worn underneath SCAPE suits. They have also been working on how to block out high noise levels; in fact, Don Doerr, chief of the Biomedical Lab, says, "The most enjoyable aspect is knowing that the Biomedical Lab and the skills of its employees have been used to support safe space flight, not only for the astronaut flight crew, but just as important for the ground processing personnel as well." The NASA Biomedical Laboratory has existed in the John F. Kennedy's Operations and Checkout Building since the Apollo Program. The primary mission of this laboratory has been the biomedical support to major, manned space programs that have included Apollo, Apollo-Soyuz, Skylab, and Shuttle. In this mission, the laboratory has been responsible in accomplishing much of the technical design, planning, provision, fabrication, and maintenance of flight and ground biomedical monitoring instrumentation. This includes the electronics in the launch flight suit and similar instrumentation systems in the spacecraft. (Note: The Lab checked out the system for STS-128 at Pad A using Firing room 4 and ground support equipment in the lab.) During Apollo, there were six engineers and ten technicians in the facility. This has evolved today to two NASA engineers and two NASA technicians, a Life Science Support contract physiologist and part-time support from an LSSC nurse and physician. Over the years, the lab has enjoyed collaboration with outside agencies and investigators. These have included on-site support to the Ames Research Center bed rest studies (seven years) and the European Space Agency studies in Toulouse, France (two years). The lab has also actively collaborated with the US Army Institute for Surgical Research, the USAF School of Aerospace Medicine, and the USN Naval Experimental Diving Unit. Because the lab often evaluates various forms of commercial-off-the-shelf life support equipment, the laboratory works closely with private companies, both domestic and foreign. The European companies seem to be more proactive and participatory with the advancement of personal protective equipment. Because these companies have viewed the space program's unique need for advanced forms of personal protective equipment, some have responded with new designs based on the prediction that these advances will soon find markets in the commercial sector. Using much of the same skills and equipment, the laboratory also addresses physiological testing of humans by supporting flight experiments and personnel involved with ground processing. While Johnson Space Center is primarily responsible for flight experiments, the Kennedy's Biomedical Lab provides the local support. However, as stated above, there are many challenges facing KSC workers that gain the attention of this lab in the measurement of the problem and the selection and testing of countermeasures. These include respiratory protection, whole body suits, hearing protection and heat stress, among many others.

A spatially explicit hydro-ecological modeling framework (BEPS-TerrainLab V2.0): Model description and test in a boreal ecosystem in Eastern North America

NASA Astrophysics Data System (ADS)

Govind, Ajit; Chen, Jing Ming; Margolis, Hank; Ju, Weimin; Sonnentag, Oliver; Giasson, Marc-André

2009-04-01

SummaryA spatially explicit, process-based hydro-ecological model, BEPS-TerrainLab V2.0, was developed to improve the representation of ecophysiological, hydro-ecological and biogeochemical processes of boreal ecosystems in a tightly coupled manner. Several processes unique to boreal ecosystems were implemented including the sub-surface lateral water fluxes, stratification of vegetation into distinct layers for explicit ecophysiological representation, inclusion of novel spatial upscaling strategies and biogeochemical processes. To account for preferential water fluxes common in humid boreal ecosystems, a novel scheme was introduced based on laboratory analyses. Leaf-scale ecophysiological processes were upscaled to canopy-scale by explicitly considering leaf physiological conditions as affected by light and water stress. The modified model was tested with 2 years of continuous measurements taken at the Eastern Old Black Spruce Site of the Fluxnet-Canada Research Network located in a humid boreal watershed in eastern Canada. Comparison of the simulated and measured ET, water-table depth (WTD), volumetric soil water content (VSWC) and gross primary productivity (GPP) revealed that BEPS-TerrainLab V2.0 simulates hydro-ecological processes with reasonable accuracy. The model was able to explain 83% of the ET, 92% of the GPP variability and 72% of the WTD dynamics. The model suggests that in humid ecosystems such as eastern North American boreal watersheds, topographically driven sub-surface baseflow is the main mechanism of soil water partitioning which significantly affects the local-scale hydrological conditions.

It's All a Matter of Perspective: Viewing First-Person Video Modeling Examples Promotes Learning of an Assembly Task

ERIC Educational Resources Information Center

Fiorella, Logan; van Gog, Tamara; Hoogerheide, Vincent; Mayer, Richard E.

2017-01-01

The present study tests whether presenting video modeling examples from the learner's (first-person) perspective promotes learning of an assembly task, compared to presenting video examples from a third-person perspective. Across 2 experiments conducted in different labs, university students viewed a video showing how to assemble an 8-component…

Enhancement of Human Effectiveness in System Design, Training, and Operation: Annual Progress Report 1 July 1973-30 June 1974.

ERIC Educational Resources Information Center

Illinois Univ., Urbana. Savoy Aviation Research Lab.

The report is concerned with research performance and results at the Savoy Aviation Research Lab. Research accomplishments are described according to eight tasks which are of two general types, those dealing with human resources research and those dealing with manned systems research. Specifically, four tasks deal primarily with pilot selection…

The changing face of the lithosphere-asthenosphere boundary: Imaging continental-scale patterns in upper mantle structure across the contiguous U.S. with Sp converted waves

NASA Astrophysics Data System (ADS)

Hopper, E.; Fischer, K. M.

2017-12-01

The contiguous U.S.A. is a rich tapestry of tectonism spanning over two billion years. On the broadest scale, this complex history can be simplified to three regimes: the tectonically active western U.S., the largely quiescent Archean and Proterozoic cratons of the central U.S., and the Phanerozoic orogen and rifted margin of the eastern U.S. The transitions between these regions can be clearly observed with Sp converted wave images of the uppermost mantle. We use common conversion point stacked Sp waves recorded by EarthScope's Transportable Array and other permanent and temporary broadband stations to image the transition from a strong, sharp velocity decrease in the shallow upper mantle of the western U.S. (the lithosphere-asthenosphere boundary, or LAB) to deeper, more diffuse features moving east that largely lie within the lithosphere. Only sparse, localized, weak phases are seen at LAB depths beneath the cratonic interior. This transition is clearly revealed by cluster analysis, which also shows the eastern U.S. as more similar to the western U.S. than the ancient interior, particularly beneath New England. In the western U.S., the observed strong LAB indicates a large enough velocity decrease to imply that melt has ponded beneath the lithosphere. We compare western U.S. LAB properties to the age distribution of most recent volcanism from NavDat. While LAB properties vary widely within a given age range, their distributions indicate a relationship between age of surface volcanism and LAB phase strength and breadth. LAB depth does not appear to have a clear correlation. In general, the LAB is strongest and broadest beneath zones that have been magmatically active in the last 50 Myr, suggesting an observable fraction of melt that is distributed over a depth range of 10's of kilometers, perhaps due to variations in the degree of thermochemical erosion of the lithosphere even on very local scales. The LAB is strongest and broadest for magmatic ages of 5-10 Ma, but beneath the youngest volcanism (<5 Ma), the LAB is seen as significantly weaker, suggesting more complete destruction of the high velocity lid. The timescale of these changes in LAB character suggests the presence and possibly production of melt in the asthenosphere for many 10's of Myr after surface volcanism ceases.

Earth analog image digitization of field, aerial, and lab experiment studies for Planetary Data System archiving.

NASA Astrophysics Data System (ADS)

Williams, D. A.; Nelson, D. M.

2017-12-01

A portion of the earth analog image archive at the Ronald Greeley Center for Planetary Studies (RGCPS)-the NASA Regional Planetary Information Facility at Arizona State University-is being digitized and will be added to the Planetary Data System (PDS) for public use. This will be a first addition of terrestrial data to the PDS specifically for comparative planetology studies. Digitization is separated into four tasks. First is the scanning of aerial photographs of volcanic and aeolian structures and flows. The second task is to scan field site images taken from ground and low-altitude aircraft of volcanic structures, lava flows, lava tubes, dunes, and wind streaks. The third image set to be scanned includes photographs of lab experiments from the NASA Planetary Aeolian Laboratory wind tunnels, vortex generator, and of wax models. Finally, rare NASA documents are being scanned and formatted as PDF files. Thousands of images are to be scanned for this project. Archiving of the data will follow the PDS4 standard, where the entire project is classified as a single bundle, with individual subjects (i.e., the Amboy Crater volcanic structure in the Mojave Desert of California) as collections. Within the collections, each image is considered a product, with a unique ID and associated XML document. Documents describing the image data, including the subject and context, will be included with each collection. Once complete, the data will be hosted by a PDS data node and available for public search and download. As one of the first earth analog datasets to be archived by the PDS, this project could prompt the digitizing and making available of historic datasets from other facilities for the scientific community.

Translating the Science of Measuring Ecosystems at a National Scale: Developing NEON's Online Learning Portal

NASA Astrophysics Data System (ADS)

Wasser, L. A.; Gram, W.; Goehring, L.

2014-12-01

"Big Data" are becoming increasingly common in many fields. The National Ecological Observatory Network (NEON) will be collecting data over the 30 years, using consistent, standardized methods across the United States. These freely available new data provide an opportunity for increased understanding of continental- and global scale processes such as changes in vegetation structure and condition, biodiversity and landuse. However, while "big data" are becoming more accessible and available, integrating big data into the university courses is challenging. New and potentially unfamiliar data types and associated processing methods, required to work with a growing diversity of available data, may warrant time and resources that present a barrier to classroom integration. Analysis of these big datasets may further present a challenge given large file sizes, and uncertainty regarding best methods to properly statistically summarize and analyze results. Finally, teaching resources, in the form of demonstrative illustrations, and other supporting media that might help teach key data concepts, take time to find and more time to develop. Available resources are often spread widely across multi-online spaces. This presentation will overview the development of NEON's collaborative University-focused online education portal. Portal content will include 1) videos and supporting graphics that explain key concepts related to NEON data products including collection methods, key metadata to consider and consideration of potential error and uncertainty surrounding data analysis; and 2) packaged "lab" activities that include supporting data to be used in an ecology, biology or earth science classroom. To facilitate broad use in classrooms, lab activities will take advantage of freely and commonly available processing tools, techniques and scripts. All NEON materials are being developed in collaboration with existing labs and organizations.

Spatial Variation of Pressure in the Lyophilization Product Chamber Part 2: Experimental Measurements and Implications for Scale-up and Batch Uniformity.

PubMed

Sane, Pooja; Varma, Nikhil; Ganguly, Arnab; Pikal, Michael; Alexeenko, Alina; Bogner, Robin H

2017-02-01

Product temperature during the primary drying step of freeze-drying is controlled by a set point chamber pressure and shelf temperature. However, recent computational modeling suggests a possible variation in local chamber pressure. The current work presents an experimental verification of the local chamber pressure gradients in a lab-scale freeze-dryer. Pressure differences between the center and the edges of a lab-scale freeze-dryer shelf were measured as a function of sublimation flux and clearance between the sublimation front and the shelf above. A modest 3-mTorr difference in pressure was observed as the sublimation flux was doubled from 0.5 to 1.0 kg·h -1 ·m -2 at a clearance of 2.6 cm. Further, at a constant sublimation flux of 1.0 kg·h -1 ·m -2 , an 8-fold increase in the pressure drop was observed across the shelf as the clearance was decreased from 4 to 1.6 cm. Scale-up of the pressure variation from lab- to a manufacturing-scale freeze-dryer predicted an increased uniformity in drying rates across the batch for two frequently used pharmaceutical excipients (mannitol and sucrose at 5% w/w). However, at an atypical condition of shelf temperature of +10°C and chamber pressure of 50 mTorr, the product temperature in the center vials was calculated to be a degree higher than the edge vial for a low resistance product, thus reversing the typical edge and center vial behavior. Thus, the effect of local pressure variation is more significant at the manufacturing-scale than at a lab-scale and accounting for the contribution of variations in the local chamber pressures can improve success in scale-up.

Computer Anxiety: How to Measure It?

ERIC Educational Resources Information Center

McPherson, Bill

1997-01-01

Provides an overview of five scales that are used to measure computer anxiety: Computer Anxiety Index, Computer Anxiety Scale, Computer Attitude Scale, Attitudes toward Computers, and Blombert-Erickson-Lowrey Computer Attitude Task. Includes background information and scale specifics. (JOW)

Object positioning in storages of robotized workcells using LabVIEW Vision

NASA Astrophysics Data System (ADS)

Hryniewicz, P.; Banaś, W.; Sękala, A.; Gwiazda, A.; Foit, K.; Kost, G.

2015-11-01

During the manufacturing process, each performed task is previously developed and adapted to the conditions and the possibilities of the manufacturing plant. The production process is supervised by a team of specialists because any downtime causes great loss of time and hence financial loss. Sensors used in industry for tracking and supervision various stages of a production process make it much easier to maintain it continuous. One of groups of sensors used in industrial applications are non-contact sensors. This group includes: light barriers, optical sensors, rangefinders, vision systems, and ultrasonic sensors. Through to the rapid development of electronics the vision systems were widespread as the most flexible type of non-contact sensors. These systems consist of cameras, devices for data acquisition, devices for data analysis and specialized software. Vision systems work well as sensors that control the production process itself as well as the sensors that control the product quality level. The LabVIEW program as well as the LabVIEW Vision and LabVIEW Builder represent the application that enables program the informatics system intended to process and product quality control. The paper presents elaborated application for positioning elements in a robotized workcell. Basing on geometric parameters of manipulated object or on the basis of previously developed graphical pattern it is possible to determine the position of particular manipulated elements. This application could work in an automatic mode and in real time cooperating with the robot control system. It allows making the workcell functioning more autonomous.

Metabolic engineering of strains: from industrial-scale to lab-scale chemical production.

PubMed

Sun, Jie; Alper, Hal S

2015-03-01

A plethora of successful metabolic engineering case studies have been published over the past several decades. Here, we highlight a collection of microbially produced chemicals using a historical framework, starting with titers ranging from industrial scale (more than 50 g/L), to medium-scale (5-50 g/L), and lab-scale (0-5 g/L). Although engineered Escherichia coli and Saccharomyces cerevisiae emerge as prominent hosts in the literature as a result of well-developed genetic engineering tools, several novel native-producing strains are gaining attention. This review catalogs the current progress of metabolic engineering towards production of compounds such as acids, alcohols, amino acids, natural organic compounds, and others.

Improving "lab-on-a-chip" techniques using biomedical nanotechnology: a review.

PubMed

Gorjikhah, Fatemeh; Davaran, Soodabeh; Salehi, Roya; Bakhtiari, Mohsen; Hasanzadeh, Arash; Panahi, Yunes; Emamverdy, Masumeh; Akbarzadeh, Abolfazl

2016-11-01

Nanotechnology and its applications in biomedical sciences principally in molecular nanodiagnostics are known as nanomolecular diagnostics, which provides new options for clinical nanodiagnostic techniques. Molecular nanodiagnostics are a critical role in the development of personalized medicine, which features point-of care performance of diagnostic procedure. This can to check patients at point-of-care facilities or in remote or resource-poor locations, therefore reducing checking time from days to minutes. In this review, applications of nanotechnology suited to biomedicine are discussed in two main class: biomedical applications for use inside (such as drugs, diagnostic techniques, prostheses, and implants) and outside the body (such as "lab-on-a-chip" techniques). A lab-on-a-chip (LOC) is a tool that incorporates numerous laboratory tasks onto a small device, usually only millimeters or centimeters in size. Finally, are discussed the applications of biomedical nanotechnology in improving "lab-on-a-chip" techniques.

Measurement of Scientific Productivity in R&D Sector: Changing paradigm.

PubMed

Kumar, Abhishek; Srivastava, Alpana; Kumar, R P Jeevan; Tiwari, Rajesh K

2017-01-01

Scientific Productivity is a demand of policy makers for a judicious utilization of massive R&D budget allocated and utilized. A huge mass of intellectual assets is employed, which after investing manpower, infrastructure and lab consumables demand for a major outcome which contributes towards building nation's economy. Scientific productivity was only measured through publications or patents. Patents, earmarked as a strong parameter for innovation generation, where, Word Intellectual Property Organisation generated a data on applications for the top 20 offices for patents, where Australia, Brazil and Canada occupied top 3 positions. India ranked 9th with the total patent applications rising from 39762 (2010) to 42854 (2014) i.e. 15%, whereas, it contributes around 2% Patents (innovative productivity) on global scale. Many studies have come forward interestingly within scientific and academic domains in the form of measurement of scientific performance, however, development of productivity indicators and calculation of Scientific Productivity (SP) as a holistic evaluation system is a significant demand. SP, a herculean task is envisaged for productivity analysis and would submit significant factors towards fabricating an effective measurement engine in a holistic manner viable for an individual and organization, being supplementary to each other. This review projects the significance of performance measurement system in R&D through identification and standardization of key parameters. It also includes emphasis on inclusion of standardized parameters, effective for performance measurement which is applicable for scientists, technical staff as well as lab as a facility. This review aims at providing an insight to the evaluators, policy makers, and high level scientific panels to stimulate the scientific intellects on identified indicators so that their work proceeds to generate productive outcome contributing to the economic growth. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Concentrated Solar Thermoelectric Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Gang; Ren, Zhifeng

2015-07-09

The goal of this project is to demonstrate in the lab that solar thermoelectric generators (STEGs) can exceed 10% solar-to-electricity efficiency, and STEGs can be integrated with phase-change materials (PCM) for thermal storage, providing operation beyond daylight hours. This project achieved significant progress in many tasks necessary to achieving the overall project goals. An accurate Themoelectric Generator (TEG) model was developed, which included realistic treatment of contact materials, contact resistances and radiative losses. In terms of fabricating physical TEGs, high performance contact materials for skutterudite TE segments were developed, along with brazing and soldering methods to assemble segmented TEGs. Accuratemore » measurement systems for determining device performance (in addition to just TE material performance) were built for this project and used to characterize our TEGs. From the optical components’ side, a spectrally selective cermet surface was developed with high solar absorptance and low thermal emittance, with thermal stability at high temperature. A measurement technique was also developed to determine absorptance and total hemispherical emittance at high temperature, and was used to characterize the fabricated spectrally selective surfaces. In addition, a novel reflective cavity was designed to reduce radiative absorber losses and achieve high receiver efficiency at low concentration ratios. A prototype cavity demonstrated that large reductions in radiative losses were possible through this technique. For the overall concentrating STEG system, a number of devices were fabricated and tested in a custom built test platform to characterize their efficiency performance. Additionally, testing was performed with integration of PCM thermal storage, and the storage time of the lab scale system was evaluated. Our latest testing results showed a STEG efficiency of 9.6%, indicating promising potential for high performance concentrated STEGs.« less

Green Infrastructure Research Promotes Students' Deeper Interest in Core Courses of a Water Resources Program

NASA Astrophysics Data System (ADS)

Yerk, W.; Montalto, F. A.; Foti, R.

2015-12-01

As one of most innovative among low impact development technologies, Green Infrastructure (GI) is a new technology that presents a range of potential research opportunities. Inherently linked to sustainability, urban quality of life, resilience, and other such topics, GI also represents a unique opportunity to highlight the social relevance of practical STEM research to undergraduate students. The nature of research on urban GI, in fact, as well as the accessibility of the GI sites, allows students to combine hands-on experience with theoretical work. Furthermore, the range of scales of the projects is such that they can be managed within a single term, but does not preclude longer engagement. The Sustainable Water Resource Engineering lab at Drexel University is engaged in two types of GI research outside the classroom. One type is a research co-op research internship. The second is a selective university-wide faculty-mentored summer scholarship STAR (Students Tackling Advanced Research) specifically designed for freshmen. The research projects we developed for those curricula can be accomplished by undergraduate students, but also address a larger research need in this emerging field. The research tasks have included identifying and calibrating affordable instruments, designing and building experimental setups, and monitoring and evaluating performance of GI sites. The work also promoted deeper understanding of the hydrological processes and initiated learning beyond the students' current curricula. The practice of the Lab's research being embedded into the educational process receives positive feedback from the students and achieves meaningful and long-lasting learning objectives. The experience helps students to students acquire hands-on experience, improves their metacognition and evidence-based inquiring into real-world problems, and further advances decision-making and communication skills.

Overcoming hurdles in translating visual search research between the lab and the field.

PubMed

Clark, Kait; Cain, Matthew S; Adamo, Stephen H; Mitroff, Stephen R

2012-01-01

Research in visual search can be vital to improving performance in careers such as radiology and airport security screening. In these applied, or "field," searches, accuracy is critical, and misses are potentially fatal; however, despite the importance of performing optimally, radiological and airport security searches are nevertheless flawed. Extensive basic research in visual search has revealed cognitive mechanisms responsible for successful visual search as well as a variety of factors that tend to inhibit or improve performance. Ideally, the knowledge gained from such laboratory-based research could be directly applied to field searches, but several obstacles stand in the way of straightforward translation; the tightly controlled visual searches performed in the lab can be drastically different from field searches. For example, they can differ in terms of the nature of the stimuli, the environment in which the search is taking place, and the experience and characteristics of the searchers themselves. The goal of this chapter is to discuss these differences and how they can present hurdles to translating lab-based research to field-based searches. Specifically, most search tasks in the lab entail searching for only one target per trial, and the targets occur relatively frequently, but field searches may contain an unknown and unlimited number of targets, and the occurrence of targets can be rare. Additionally, participants in lab-based search experiments often perform under neutral conditions and have no formal training or experience in search tasks; conversely, career searchers may be influenced by the motivation to perform well or anxiety about missing a target, and they have undergone formal training and accumulated significant experience searching. This chapter discusses recent work that has investigated the impacts of these differences to determine how each factor can influence search performance. Knowledge gained from the scientific exploration of search can be applied to field searches but only when considering and controlling for the differences between lab and field.

Stream piracy in the Black Hills: A geomorphology lab exercise

USGS Publications Warehouse

Zaprowski, B.J.; Evenson, E.B.; Epstein, J.B.

2002-01-01

The Black Hills of South Dakota exhibits many fine examples of stream piracy that are very suitable for teaching geomorphology lab exercises. This lab goes beyond standard topographic map interpretation by using geologic maps, well logs, gravel provenance and other types of data to teach students about stream piracy. Using a step-by-step method in which the lab exercises ramp up in difficulty, students hone their skills in deductive reasoning and data assimilation. The first exercises deal with the identification of stream piracy at a variety of spatial scales and the lab culminates with an exercise on landscape evolution and drainage rearrangement.

Application of Lactic Acid Bacteria (LAB) in freshness keeping of tilapia fillets as sashimi

NASA Astrophysics Data System (ADS)

Cao, Rong; Liu, Qi; Chen, Shengjun; Yang, Xianqing; Li, Laihao

2015-08-01

Aquatic products are extremely perishable food commodities. Developing methods to keep the freshness of fish represents a major task of the fishery processing industry. Application of Lactic Acid Bacteria (LAB) as food preservative is a novel approach. In the present study, the possibility of using lactic acid bacteria in freshness keeping of tilapia fillets as sashimi was examined. Fish fillets were dipped in Lactobacillus plantarum 1.19 (obtained from China General Microbiological Culture Collection Center) suspension as LAB-treated group. Changes in K-value, APC, sensory properties and microbial flora were analyzed. Results showed that LAB treatment slowed the increase of K-value and APC in the earlier storage, and caused a smooth decrease in sensory score. Gram-negative bacteria dominated during refrigerated storage, with Pseudomonas and Aeromonas being relatively abundant. Lactobacillus plantarum 1.19 had no obvious inhibitory effect against these Gram-negatives. However, Lactobacillus plantarum 1.19 changed the composition of Gram-positive bacteria. No Micrococcus were detected and the proportion of Staphylococcus decreased in the spoiled LAB-treated samples. The period that tilapia fillets could be used as sashimi material extended from 24 h to 48 h after LAB treatment. The potential of using LAB in sashimi processing was confirmed.

An over-view of robot assisted surgery curricula and the status of their validation.

PubMed

Fisher, Rebecca A; Dasgupta, Prokar; Mottrie, Alex; Volpe, Alessandro; Khan, Mohammed S; Challacombe, Ben; Ahmed, Kamran

2015-01-01

Robotic surgery is a rapidly expanding field. Thus far training for robotic techniques has been unstructured and the requirements are variable across various regions. Several projects are currently underway to develop a robotic surgery curriculum and are in various stages of validation. We aimed to outline the structures of available curricula, their process of development, validation status and current utilization. We undertook a literature review of papers including the MeSH terms "Robotics" and "Education". When we had an overview of curricula in development, we searched recent conference abstracts to gain up to date information. The main curricula are the FRS, the FSRS, the Canadian BSTC and the ERUS initiative. They are in various stages of validation and offer a mixture of theoretical and practical training, using both physical and simulated models. Whilst the FSRS is based on tasks on the RoSS virtual reality simulator, FRS and BSTC are designed for use on simulators and the robot itself. The ERUS curricula benefits from a combination of dry lab, wet lab and virtual reality components, which may allow skills to be more transferable to the OR as tasks are completed in several formats. Finally, the ERUS curricula includes the OR modular training programme as table assistant and console surgeon. Curricula are a crucial step in global standardisation of training and certification of surgeons for robotic surgical procedures. Many curricula are in early stages of development and more work is needed in development and validation of these programmes before training can be standardised. Copyright © 2014 Surgical Associates Ltd. Published by Elsevier Ltd. All rights reserved.

Use MACES IVA Suit for EVA Mobility Evaluations

NASA Technical Reports Server (NTRS)

Watson, Richard D.

2014-01-01

The use of an Intra-Vehicular Activity (IVA) suit for a spacewalk or Extra-Vehicular Activity (EVA) was evaluated for mobility and usability in the Neutral Buoyancy Lab (NBL) environment. The Space Shuttle Advanced Crew Escape Suit (ACES) has been modified (MACES) to integrate with the Orion spacecraft. The first several missions of the Orion MPCV spacecraft will not have mass available to carry an EVA specific suit so any EVA required will have to be performed by the MACES. Since the MACES was not designed with EVA in mind, it was unknown what mobility the suit would be able to provide for an EVA or if a person could perform useful tasks for an extended time inside the pressurized suit. The suit was evaluated in multiple NBL runs by a variety of subjects including crewmembers with significant EVA experience. Various functional mobility tasks performed included: translation, body positioning, carrying tools, body stabilization, equipment handling, and use of tools. Hardware configurations included with and without TMG, suit with IVA gloves and suit with EVA gloves. Most tasks were completed on ISS mockups with existing EVA tools. Some limited tasks were completed with prototype tools on a simulated rocky surface. Major findings include: demonstration of the ability to weigh-out the suit, understanding the need to have subjects perform multiple runs prior to getting feedback, determination of critical sizing factors, and need for adjustment of suit work envelop. The early testing has demonstrated the feasibility of EVA's limited duration and limited scope. Further testing is required with more flight like tasking and constraints to validate these early results. If the suit is used for EVA, it will require mission specific modifications for umbilical management or PLSS integration, safety tether attachment, and tool interfaces. These evaluations are continuing through calendar year 2014.

Using Optimization to Improve NASA Extravehicular Activity Planning

DTIC Science & Technology

2012-09-01

Mission Operations Directorate NASA National Aeronautics and Space Administration NBL Neutral Buoyancy Laboratory ORU Orbital Replacement Unit PET...training is conducted in the Neutral Buoyancy Lab ( NBL ) for full dress rehearsal. The active response gravity offload system is a facility that helps...three NBL runs are dedicated to task and timeline duration validation in normal circumstances, with the possibility of more if the tasks and procedures

Improvement of workload estimation techniques in piloting tasks

NASA Technical Reports Server (NTRS)

Wierwille, W. W.

1984-01-01

The Modified Cooper-Harper (MCH) scale has been shown to be a sensitive indicator of workload in several different types of aircrew tasks. The MCH scale, which is a 10 point scale, and five newly devised scales were examined in two different aircraft simulator experiments in which pilot loading was treated as an independent variable. The five scales included a 15 point scale, computerized versions of the MCH and 15 point scales, a scale in which the decision tree was removed, and one in which a 15 point left-to-right format was used. The results indicate that while one of the new scales may be more sensitive in a given experiment, task dependency is a problem. The MCH scale on the other hand exhibits consistent sensitivity and remains the scale recommended for general use. The MCH scale results are consistent with earlier experiments also. The results of the rating scale experiments are presented and the questionnaire results which were directed at obtaining a better understanding of the reasons for the relative sensitivity of the MCH scale and its variations are described.

Newly Elaborated Multipurpose Polymer Electrolyte Encompassing RTILs for Smart Energy-Efficient Devices.

PubMed

Nair, Jijeesh R; Porcarelli, Luca; Bella, Federico; Gerbaldi, Claudio

2015-06-17

Profoundly ion-conducting, self-standing, and tack-free ethylene oxide-based polymer electrolytes encompassing a room-temperature ionic liquid (RTIL) with specific amounts of lithium salt are successfully prepared via a rapid and easily upscalable process including a UV irradiation step. All prepared materials are thoroughly characterized in terms of their physical, chemical, and morphological properties and eventually galvanostatically cycled in lab-scale lithium batteries (LIBs) exploiting a novel direct polymerization procedure to get intimate electrode/electrolyte interfacial characteristics. The promising multipurpose characteristics of the newly elaborated materials are demonstrated by testing them in dye-sensitized solar cells (DSSCs), where the introduction of the iodine/iodide-based redox mediator in the polymer matrix assured the functioning of a lab-scale test cell with conversion efficiency exceeding 6% at 1 sun. The reported results enlighten the promising prospects of the material to be successfully implemented as stable, durable, and efficient electrolyte in next-generation energy conversion and storage devices.

A Platform for Scalable Satellite and Geospatial Data Analysis

NASA Astrophysics Data System (ADS)

Beneke, C. M.; Skillman, S.; Warren, M. S.; Kelton, T.; Brumby, S. P.; Chartrand, R.; Mathis, M.

2017-12-01

At Descartes Labs, we use the commercial cloud to run global-scale machine learning applications over satellite imagery. We have processed over 5 Petabytes of public and commercial satellite imagery, including the full Landsat and Sentinel archives. By combining open-source tools with a FUSE-based filesystem for cloud storage, we have enabled a scalable compute platform that has demonstrated reading over 200 GB/s of satellite imagery into cloud compute nodes. In one application, we generated global 15m Landsat-8, 20m Sentinel-1, and 10m Sentinel-2 composites from 15 trillion pixels, using over 10,000 CPUs. We recently created a public open-source Python client library that can be used to query and access preprocessed public satellite imagery from within our platform, and made this platform available to researchers for non-commercial projects. In this session, we will describe how you can use the Descartes Labs Platform for rapid prototyping and scaling of geospatial analyses and demonstrate examples in land cover classification.

Phosphate interference during in situ treatment for arsenic in groundwater.

PubMed

Brunsting, Joseph H; McBean, Edward A

2014-01-01

Contamination of groundwater by arsenic is a problem in many areas of the world, particularly in West Bengal (India) and Bangladesh, where reducing conditions in groundwater are the cause. In situ treatment is a novel approach wherein, by introduction of dissolved oxygen (DO), advantages over other treatment methods can be achieved through simplicity, not using chemicals, and not requiring disposal of arsenic-rich wastes. A lab-scale test of in situ treatment by air sparging, using a solution with approximately 5.3 mg L(-1) ferrous iron and 200 μg L(-1) arsenate, showed removal of arsenate in the range of 59%. A significant obstacle exists, however, due to the interference of phosphate since phosphate competes for adsorption sites on oxidized iron precipitates. A lab-scale test including 0.5 mg L(-1) phosphate showed negligible removal of arsenate. In situ treatment by air sparging demonstrates considerable promise for removal of arsenic from groundwater where iron is present in considerable quantities and phosphates are low.

Comparison between lab- and full-scale applications of in situ aeration of an old landfill and assessment of long-term emission development after completion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hrad, Marlies; Gamperling, Oliver; Huber-Humer, Marion, E-mail: marion.huber-humer@boku.ac.at

Highlights: ► Current data on in situ aeration effects from the first Austrian full-scale case study. ► Data on lasting waste stabilisation after aeration completion. ► Information on the transferability of results from lab- to full-scale aeration. - Abstract: Sustainable landfilling has become a fundamental objective in many modern waste management concepts. In this context, the in situ aeration of landfills has been recognised for its potential to convert conventional anaerobic landfills into biological stabilised state, whereby both current and potential (long-term) emissions of the landfilled waste are mitigated. In recent years, different in situ aeration concepts have been successfullymore » applied in Europe, North America and Asia, all pursuing different objectives and strategies. In Austria, the first full-scale application of in situ landfill aeration by means of low pressure air injection and simultaneous off-gas collection and treatment was implemented on an old, small municipal solid waste (MSW) landfill (2.6 ha) in autumn 2007. Complementary laboratory investigations were conducted with waste samples taken from the landfill site in order to provide more information on the transferability of the results from lab- to full-scale aeration measures. In addition, long-term emission development of the stabilised waste after aeration completion was assessed in an ongoing laboratory experiment. Although the initial waste material was described as mostly stable in terms of the biological parameters gas generation potential over 21 days (GP{sub 21}) and respiration activity over 4 days (RA{sub 4}), the lab-scale experiments indicated that aeration, which led to a significant improvement of leachate quality, was accompanied by further measurable changes in the solid waste material under optimised conditions. Even 75 weeks after aeration completion the leachate, as well as gaseous emissions from the stabilised waste material, remained low and stayed below the authorised Austrian discharge limits. However, the application of in situ aeration at the investigated landfill is a factor 10 behind the lab-based predictions after 3 years of operation, mainly due to technical limitations in the full-scale operation (e.g. high air flow resistivity due to high water content of waste and temporarily high water levels within the landfill; limited efficiency of the aeration wells). In addition, material preparation (e.g. sieving, sorting and homogenisation) prior to the emplacement in Landfill Simulation Reactors (LSRs) must be considered when transferring results from lab- to full-scale application.« less

Tacit knowledge: A refinement and empirical test of the Academic Tacit Knowledge Scale.

PubMed

Insch, Gary S; McIntyre, Nancy; Dawley, David

2008-11-01

Researchers have linked tacit knowledge to improved organizational performance, but research on how to measure tacit knowledge is scarce. In the present study, the authors proposed and empirically tested a model of tacit knowledge and an accompanying measurement scale of academic tacit knowledge. They present 6 hypotheses that support the proposed tacit knowledge model regarding the role of cognitive (self-motivation, self-organization); technical (individual task, institutional task); and social (task-related, general) skills. The authors tested these hypotheses with 542 responses to the Academic Tacit Knowledge Scale, which included the respondents' grade point average-the performance variable. All 6 hypotheses were supported.

Simultaneous Microwave Extraction and Separation of Volatile and Non-Volatile Organic Compounds of Boldo Leaves. From Lab to Industrial Scale

PubMed Central

Petigny, Loïc; Périno, Sandrine; Minuti, Matteo; Visinoni, Francesco; Wajsman, Joël; Chemat, Farid

2014-01-01

Microwave extraction and separation has been used to increase the concentration of the extract compared to the conventional method with the same solid/liquid ratio, reducing extraction time and separate at the same time Volatile Organic Compounds (VOC) from non-Volatile Organic Compounds (NVOC) of boldo leaves. As preliminary study, a response surface method has been used to optimize the extraction of soluble material and the separation of VOC from the plant in laboratory scale. The results from the statistical analysis revealed that the optimized conditions were: microwave power 200 W, extraction time 56 min and solid liquid ratio of 7.5% of plants in water. Lab scale optimized microwave method is compared to conventional distillation, and requires a power/mass ratio of 0.4 W/g of water engaged. This power/mass ratio is kept in order to upscale from lab to pilot plant. PMID:24776762

Planning a Computer Lab: Considerations To Ensure Success.

ERIC Educational Resources Information Center

IALL Journal of Language Learning Technologies, 1994

1994-01-01

Presents points to consider when organizing a computer laboratory. These include the lab's overall objectives and how best to meet them; what type of students will use the lab; where the lab will be located; and what software and hardware can best meet the lab's overall objectives, population, and location requirements. Other factors include time,…

Computerized Hammer Sounding Interpretation for Concrete Assessment with Online Machine Learning.

PubMed

Ye, Jiaxing; Kobayashi, Takumi; Iwata, Masaya; Tsuda, Hiroshi; Murakawa, Masahiro

2018-03-09

Developing efficient Artificial Intelligence (AI)-enabled systems to substitute the human role in non-destructive testing is an emerging topic of considerable interest. In this study, we propose a novel hammering response analysis system using online machine learning, which aims at achieving near-human performance in assessment of concrete structures. Current computerized hammer sounding systems commonly employ lab-scale data to validate the models. In practice, however, the response signal patterns can be far more complicated due to varying geometric shapes and materials of structures. To deal with a large variety of unseen data, we propose a sequential treatment for response characterization. More specifically, the proposed system can adaptively update itself to approach human performance in hammering sounding data interpretation. To this end, a two-stage framework has been introduced, including feature extraction and the model updating scheme. Various state-of-the-art online learning algorithms have been reviewed and evaluated for the task. To conduct experimental validation, we collected 10,940 response instances from multiple inspection sites; each sample was annotated by human experts with healthy/defective condition labels. The results demonstrated that the proposed scheme achieved favorable assessment accuracy with high efficiency and low computation load.

Successes and Challenges in Transitioning to Large Enrollment NEXUS/Physics IPLS Labs

NASA Astrophysics Data System (ADS)

Moore, Kimberly

2017-01-01

UMd-PERG's NEXUS/Physics for Life Sciences laboratory curriculum, piloted in 2012-2013 in small test classes, has been implemented in large-enrollment environments at UMD from 2013-present. These labs address physical issues at biological scales using microscopy, image and video analysis, electrophoresis, and spectroscopy in an open, non-protocol-driven environment. We have collected a wealth of data (surveys, video analysis, etc.) that enables us to get a sense of the students' responses to this curriculum in a large-enrollment environment and with teaching assistants both `new to' and `experienced in' the labs. In this talk, we will provide a brief overview of what we have learned, including the challenges of transitioning to large N, student perception then and now, and comparisons of our large-enrollment results to the results from our pilot study. We will close with a discussion of the acculturation of teaching assistants to this novel environment and suggestions for sustainability.

FY17 ISCR Scholar End-of-Assignment Report - Robbie Sadre

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sadre, R.

2017-10-20

Throughout this internship assignment, I did various tasks that contributed towards the starting of the SASEDS (Safe Active Scanning for Energy Delivery Systems) and CES-21 (California Energy Systems for the 21st Century) projects in the SKYFALL laboratory. The goal of the SKYFALL laboratory is to perform modeling and simulation verification of transmission power system devices, while integrating with high-performance computing. The first thing I needed to do was acquire official Online LabVIEW training from National Instruments. Through these online tutorial modules, I learned the basics of LabVIEW, gaining experience in connecting to NI devices through the DAQmx API as wellmore » as LabVIEW basic programming techniques (structures, loops, state machines, front panel GUI design etc).« less

Open web system of Virtual labs for nuclear and applied physics

NASA Astrophysics Data System (ADS)

Saldikov, I. S.; Afanasyev, V. V.; Petrov, V. I.; Ternovykh, M. Yu

2017-01-01

An example of virtual lab work on unique experimental equipment is presented. The virtual lab work is software based on a model of real equipment. Virtual labs can be used for educational process in nuclear safety and analysis field. As an example it includes the virtual lab called “Experimental determination of the material parameter depending on the pitch of a uranium-water lattice”. This paper included general description of this lab. A description of a database on the support of laboratory work on unique experimental equipment which is included this work, its concept development are also presented.

Electrifying the disk: a modular rotating platform for wireless power and data transmission for Lab on a disk application.

PubMed

Höfflin, Jens; Torres Delgado, Saraí M; Suárez Sandoval, Fralett; Korvink, Jan G; Mager, Dario

2015-06-21

We present a design for wireless power transfer, via inductively coupled coils, to a spinning disk. The rectified and stabilised power feeds an Arduino-compatible microcontroller (μC) on the disc, which in turn drives and monitors various sensors and actuators. The platform, which has been conceived to flexibly prototype such systems, demonstrates the feasibility of a wireless power supply and the use of a μC circuit, for example for Lab-on-a-disk applications, thereby eliminating the need for cumbersome slip rings or batteries, and adding a cogent and new degree of freedom to the setup. The large number of sensors and actuators included demonstrate that a wide range of physical parameters can be easily monitored and altered. All devices are connected to the μC via an I(2)C bus, therefore can be easily exchanged or augmented by other devices in order to perform a specific task on the disk. The wireless power supply takes up little additional physical space and should work in conjunction with most existing Lab-on-a-disk platforms as a straightforward add-on, since it does not require modification of the rotation axis and can be readily adapted to specific geometrical requirements.

Precision pointing and control of flexible spacecraft

NASA Technical Reports Server (NTRS)

Bantell, M. H., Jr.

1987-01-01

The problem and long term objectives for the precision pointing and control of flexible spacecraft are given. The four basic objectives are stated in terms of two principle tasks. Under Task 1, robust low order controllers, improved structural modeling methods for control applications and identification methods for structural dynamics are being developed. Under Task 2, a lab test experiment for verification of control laws and system identification algorithms is being developed. For Task 1, work has focused on robust low order controller design and some initial considerations for structural modeling in control applications. For Task 2, work has focused on experiment design and fabrication, along with sensor selection and initial digital controller implementation. Conclusions are given.

Discovery of a Protocluster Associated with a Lyα Blob Pair at z = 2.3

NASA Astrophysics Data System (ADS)

Bădescu, Toma; Yang, Yujin; Bertoldi, Frank; Zabludoff, Ann; Karim, Alexander; Magnelli, Benjamin

2017-08-01

Bright Lyα blobs (LABs)—extended nebulae with sizes of ˜100 kpc and Lyα luminosities of ˜1044 erg s-1—often reside in overdensities of compact Lyα emitters (LAEs) that may be galaxy protoclusters. The number density, variance, and internal kinematics of LABs suggest that they themselves trace group-like halos. Here, we test this hierarchical picture, presenting deep, wide-field Lyα narrowband imaging of a 1° × 0.°5 region around a LAB pair at z = 2.3 discovered previously by a blind survey. We find 183 Lyα emitters, including the original LAB pair and three new LABs with Lyα luminosities of (0.9{--}1.3)× {10}43 erg s-1 and isophotal areas of 16-24 arcsec2. Using the LAEs as tracers and a new kernel density estimation method, we discover a large-scale overdensity (Boötes J1430+3522) with a surface density contrast of {δ }{{Σ }}=2.7, a volume density contrast of δ ˜10.4, and a projected diameter of ≈20 comoving Mpc. Comparing with cosmological simulations, we conclude that this LAE overdensity will evolve into a present-day Coma-like cluster with {log}(M/{M}⊙ ) ˜ 15.1 ± 0.2. In this and three other wide-field LAE surveys re-analyzed here, the extents and peak amplitudes of the largest LAE overdensities are similar, not increasing with survey size, and implying that they were indeed the largest structures then and today evolve into rich clusters. Intriguingly, LABs favor the outskirts of the densest LAE concentrations, I.e., intermediate LAE overdensities of {δ }{{Σ }}=1{--}2. We speculate that these LABs mark infalling protogroups being accreted by the more massive protocluster.

TIMESERIESSTREAMING.VI: LabVIEW program for reliable data streaming of large analog time series

NASA Astrophysics Data System (ADS)

Czerwinski, Fabian; Oddershede, Lene B.

2011-02-01

With modern data acquisition devices that work fast and very precise, scientists often face the task of dealing with huge amounts of data. These need to be rapidly processed and stored onto a hard disk. We present a LabVIEW program which reliably streams analog time series of MHz sampling. Its run time has virtually no limitation. We explicitly show how to use the program to extract time series from two experiments: For a photodiode detection system that tracks the position of an optically trapped particle and for a measurement of ionic current through a glass capillary. The program is easy to use and versatile as the input can be any type of analog signal. Also, the data streaming software is simple, highly reliable, and can be easily customized to include, e.g., real-time power spectral analysis and Allan variance noise quantification. Program summaryProgram title: TimeSeriesStreaming.VI Catalogue identifier: AEHT_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEHT_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 250 No. of bytes in distributed program, including test data, etc.: 63 259 Distribution format: tar.gz Programming language: LabVIEW ( http://www.ni.com/labview/) Computer: Any machine running LabVIEW 8.6 or higher Operating system: Windows XP and Windows 7 RAM: 60-360 Mbyte Classification: 3 Nature of problem: For numerous scientific and engineering applications, it is highly desirable to have an efficient, reliable, and flexible program to perform data streaming of time series sampled with high frequencies and possibly for long time intervals. This type of data acquisition often produces very large amounts of data not easily streamed onto a computer hard disk using standard methods. Solution method: This LabVIEW program is developed to directly stream any kind of time series onto a hard disk. Due to optimized timing and usage of computational resources, such as multicores and protocols for memory usage, this program provides extremely reliable data acquisition. In particular, the program is optimized to deal with large amounts of data, e.g., taken with high sampling frequencies and over long time intervals. The program can be easily customized for time series analyses. Restrictions: Only tested in Windows-operating LabVIEW environments, must use TDMS format, acquisition cards must be LabVIEW compatible, driver DAQmx installed. Running time: As desirable: microseconds to hours

Defense Science Board Task Force Report: The Role of Autonomy in DoD Systems

DTIC Science & Technology

2012-07-01

ASD(R&E) and the Military Services should schedule periodic, on-site collaborations that bring together academia, government and not-for-profit labs...expressing UxV activities, increased problem solving, planning and scheduling capabilities to enable dynamic tasking of distributed UxVs and tools for...industrial, governmental and military. Manufacturing has long exploited planning for logistics and matching product demand to production schedules

Auditory Learning Using a Portable Real-Time Vocoder: Preliminary Findings

PubMed Central

Pisoni, David B.

2015-01-01

Purpose Although traditional study of auditory training has been in controlled laboratory settings, interest has been increasing in more interactive options. The authors examine whether such interactive training can result in short-term perceptual learning, and the range of perceptual skills it impacts. Method Experiments 1 (N = 37) and 2 (N = 21) used pre- and posttest measures of speech and nonspeech recognition to find evidence of learning (within subject) and to compare the effects of 3 kinds of training (between subject) on the perceptual abilities of adults with normal hearing listening to simulations of cochlear implant processing. Subjects were given interactive, standard lab-based, or control training experience for 1 hr between the pre- and posttest tasks (unique sets across Experiments 1 & 2). Results Subjects receiving interactive training showed significant learning on sentence recognition in quiet task (Experiment 1), outperforming controls but not lab-trained subjects following training. Training groups did not differ significantly on any other task, even those directly involved in the interactive training experience. Conclusions Interactive training has the potential to produce learning in 1 domain (sentence recognition in quiet), but the particulars of the present training method (short duration, high complexity) may have limited benefits to this single criterion task. PMID:25674884

The Effects of Preference for Information on Consumers’ Online Health Information Search Behavior

PubMed Central

2013-01-01

Background Preference for information is a personality trait that affects people’s tendency to seek information in health-related situations. Prior studies have focused primarily on investigating its impact on patient-provider communication and on the implications for designing information interventions that prepare patients for medical procedures. Few studies have examined its impact on general consumers’ interactions with Web-based search engines for health information or the implications for designing more effective health information search systems. Objective This study intends to fill this gap by investigating the impact of preference for information on the search behavior of general consumers seeking health information, their perceptions of search tasks (representing information needs), and user experience with search systems. Methods Forty general consumers who had previously searched for health information online participated in the study in our usability lab. Preference for information was measured using Miller’s Monitor-Blunter Style Scale (MBSS) and the Krantz Health Opinion Survey-Information Scale (KHOS-I). Each participant completed four simulated health information search tasks: two look-up (fact-finding) and two exploratory. Their behaviors while interacting with the search systems were automatically logged and ratings of their perceptions of tasks and user experience with the systems were collected using Likert-scale questionnaires. Results The MBSS showed low reliability with the participants (Monitoring subscale: Cronbach alpha=.53; Blunting subscale: Cronbach alpha=.35). Thus, no further analyses were performed based on the scale. KHOS-I had sufficient reliability (Cronbach alpha=.77). Participants were classified into low- and high-preference groups based on their KHOS-I scores. The high-preference group submitted significantly shorter queries when completing the look-up tasks (P=.02). The high-preference group made a significantly higher percentage of parallel movements in query reformulation than did the low-preference group (P=.04), whereas the low-preference group made a significantly higher percentage of new concept movements than the high-preference group when completing the exploratory tasks (P=.01). The high-preference group found the exploratory tasks to be significantly more difficult (P=.05) and the systems to be less useful (P=.04) than did the low-preference group. Conclusions Preference for information has an impact on the search behavior of general consumers seeking health information. Those with a high preference were more likely to use more general queries when searching for specific factual information and to develop more complex mental representations of health concerns of an exploratory nature and try different combinations of concepts to explore these concerns. High-preference users were also more demanding on the system. Health information search systems should be tailored to fit individuals’ information preferences. PMID:24284061

The effects of preference for information on consumers' online health information search behavior.

PubMed

Zhang, Yan

2013-11-26

Preference for information is a personality trait that affects people's tendency to seek information in health-related situations. Prior studies have focused primarily on investigating its impact on patient-provider communication and on the implications for designing information interventions that prepare patients for medical procedures. Few studies have examined its impact on general consumers' interactions with Web-based search engines for health information or the implications for designing more effective health information search systems. This study intends to fill this gap by investigating the impact of preference for information on the search behavior of general consumers seeking health information, their perceptions of search tasks (representing information needs), and user experience with search systems. Forty general consumers who had previously searched for health information online participated in the study in our usability lab. Preference for information was measured using Miller's Monitor-Blunter Style Scale (MBSS) and the Krantz Health Opinion Survey-Information Scale (KHOS-I). Each participant completed four simulated health information search tasks: two look-up (fact-finding) and two exploratory. Their behaviors while interacting with the search systems were automatically logged and ratings of their perceptions of tasks and user experience with the systems were collected using Likert-scale questionnaires. The MBSS showed low reliability with the participants (Monitoring subscale: Cronbach alpha=.53; Blunting subscale: Cronbach alpha=.35). Thus, no further analyses were performed based on the scale. KHOS-I had sufficient reliability (Cronbach alpha=.77). Participants were classified into low- and high-preference groups based on their KHOS-I scores. The high-preference group submitted significantly shorter queries when completing the look-up tasks (P=.02). The high-preference group made a significantly higher percentage of parallel movements in query reformulation than did the low-preference group (P=.04), whereas the low-preference group made a significantly higher percentage of new concept movements than the high-preference group when completing the exploratory tasks (P=.01). The high-preference group found the exploratory tasks to be significantly more difficult (P=.05) and the systems to be less useful (P=.04) than did the low-preference group. Preference for information has an impact on the search behavior of general consumers seeking health information. Those with a high preference were more likely to use more general queries when searching for specific factual information and to develop more complex mental representations of health concerns of an exploratory nature and try different combinations of concepts to explore these concerns. High-preference users were also more demanding on the system. Health information search systems should be tailored to fit individuals' information preferences.

Situational Awareness and Communication Experiment for Military Operations in Urban Terrain: Experiment 1

DTIC Science & Technology

2001-10-01

CO (N tN IN ^ j co co co in in T-l (A \\ D ^o o o eg z <Z \\0 IN i-i o co oo I D co c o z <Z in es co ■>* IN...NATL LAB ENGNRNG MECHANICS DEPT MS 9042 ATTN J HANDROCK YRKAN JLAUFFER PO BOX 969 LIVERMORE CA 94551-0969 US ARMY RSCHINST ATTN PERI IK D L...would be included in the AC. Van Cott and Paramore (1988) defined a task as a goal- directed behavior. Since the purpose was to develop an AC for

Can Random Mutation Mimic Design?: A Guided Inquiry Laboratory for Undergraduate Students

PubMed Central

Kalinowski, Steven T.; Taper, Mark L.; Metz, Anneke M.

2006-01-01

Complex biological structures, such as the human eye, have been interpreted as evidence for a creator for over three centuries. This raises the question of whether random mutation can create such adaptations. In this article, we present an inquiry-based laboratory experiment that explores this question using paper airplanes as a model organism. The main task for students in this investigation is to figure out how to simulate paper airplane evolution (including reproduction, inheritance, mutation, and selection). In addition, the lab requires students to practice analytic thinking and to carefully delineate the implications of their results. PMID:16951065

Task 3 - Pyrolysis of Plastic Waste. Semiannual report, November 1, 1996--March 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ness, Robert O.; Aulich, Ted R.

1997-12-31

Over the last 50 years, the U.S. Department of Energy (DOE) has produced a wide variety of radioactive wastes from activities associated with nuclear defense and nuclear power generation. These wastes include low-level radioactive solid wastes, mixed wastes, and transuranic (TRU) wastes. A portion of these wastes consists of high- organic-content materials, such as resins, plastics, and other polymers; synthetic and natural rubbers; cellulosic-based materials; and oils, organic solvents, and chlorinated organic solvents. Many of these wastes contain hazardous and/or pyrophoric materials in addition to radioactive species. Physical forms of the waste include ion-exchange resins used to remove radioactive elementsmore » from nuclear reactor cooling water, lab equipment and tools (e.g., measurement and containment vessels, hoses, wrappings, equipment coverings and components, and countertops), oil products (e.g., vacuum pump and lubrication oils), bags and other storage containers (for liquids, solids, and gases), solvents, gloves, lab coats and anti-contamination clothing, and other items. Major polymer and chemical groups found in high-organic-content radioactive wastes include polyvinyl chloride (PVC), low-density polyethylene (LDPE), polypropylene (PP), Teflon(TM), polystyrene (PS), nylon, latex, polyethylene terephthalate (PET), vinyl, high-density polyethylene (HDPE), polycarbonate, nitriles, Tygon(R), butyl, and Tyvec(R).« less

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Pilot-Scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary M. Blythe

2006-03-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, ''Field Testing of a Wet FGD Additive.'' The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemissions of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate that the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal.more » The project will conduct pilot and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosage requirements to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB co-fired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot and full-scale jet bubbling reactor (JBR) FGD systems to be tested. A third utility, to be named later, will provide the high-sulfur Eastern bituminous coal full-scale FGD test site. Degussa Corporation is providing the TMT-15 additive and technical support to the test program. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High Sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. This topical report presents the results from the Task 2 and Task 4 pilot-scale additive tests. The Task 3 and Task 5 full-scale additive tests will be conducted later in calendar year 2006.« less

Visual Inspection Research Project Report on Benchmark Inspections

DOT National Transportation Integrated Search

1996-10-01

Word document. Recognizing the importance of visual inspection in the maintenance of the civil air fleet, the FAA tasked the Aging Aircraft Nondestructive Inspection Validation Center (AANC) at Sandia National Labs in Albuquerque, NM, to establish a ...

High Contrast Internal and External Coronagraph Masks Produced by Various Techniques

NASA Technical Reports Server (NTRS)

Balasubramanian, Kunjithapatha; Wilson, Daniel; White, Victor; Muller, Richard; Dickie, Matthew; Yee, Karl; Ruiz, Ronald; Shaklan, Stuart; Cady, Eric; Kern, Brian;

Developing a Natural User Interface and Facial Recognition System With OpenCV and the Microsoft Kinect

NASA Technical Reports Server (NTRS)

Gutensohn, Michael

2018-01-01

The task for this project was to design, develop, test, and deploy a facial recognition system for the Kennedy Space Center Augmented/Virtual Reality Lab. This system will serve as a means of user authentication as part of the NUI of the lab. The overarching goal is to create a seamless user interface that will allow the user to initiate and interact with AR and VR experiences without ever needing to use a mouse or keyboard at any step in the process.

Perspectives on ecological research at the Outdoor StreamLab, a field-scale experimental stream

NASA Astrophysics Data System (ADS)

Merten, E. C.; Dieterman, D.; Kramarczuk, K.; Lightbody, A.; Orr, C. H.; Wellnitz, T.

2009-12-01

Artificial streams hold great promise for examining ecological processes. They lend themselves to manipulations of discharge, sediment load, water chemistry, and other parameters difficult or impossible to control in natural streams. However, artificial streams also have important limitations. In this presentation we describe insights gained from several ecological studies conducted at the St. Anthony Falls Laboratory’s Outdoor StreamLab, including, 1) short-term turbidity exposure effects on fish health, 2) macroinvertebrate grazing rates on periphyton as a function of velocity, 3) rates of macroinvertebrate colonization as related to velocity, and 4) fine-scale correlations of periphytic biomass with hydraulic conditions. Several lessons emerge from these initial attempts at ecological research in the Outdoor StreamLab. We have learned that the size, flow rate, substrate, water chemistry, and available colonization population of the artificial stream limit the kinds of organisms and types of ecological processes that can be examined and the types of experiments that can be run. We suggest that short-term biotic responses are best for study in a system of this type, and note that constant experiment maintenance is essential. Operating artificial streams to meet the needs of multiple researchers also presents challenges of scheduling, coordination, and conflict resolution. Although ecological research in artificial streams has considerable potential, the planning required is no less than that of traditional field studies.

Characterization Of The As-Received Sludge Batch 9 Qualification Sample (Htf-51-15-81)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J.

Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) has sent SRNL a 3-L slurried sample of Tank 51H (HTF-51-15-81) to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (potentially after combining with Tank 40H sludge). This report documents the first steps of the qualification process – characterization of the as-received Tank 51H qualification sample. These results will be used to support a reprojection of SB9more » by SRR from which final Tank 51H washing, frit development, and Chemical Processing Cell (CPC) activities will be based.« less

Continuously-stirred anaerobic digester to convert organic wastes into biogas: system setup and basic operation.

PubMed

Usack, Joseph G; Spirito, Catherine M; Angenent, Largus T

2012-07-13

Anaerobic digestion (AD) is a bioprocess that is commonly used to convert complex organic wastes into a useful biogas with methane as the energy carrier. Increasingly, AD is being used in industrial, agricultural, and municipal waste(water) treatment applications. The use of AD technology allows plant operators to reduce waste disposal costs and offset energy utility expenses. In addition to treating organic wastes, energy crops are being converted into the energy carrier methane. As the application of AD technology broadens for the treatment of new substrates and co-substrate mixtures, so does the demand for a reliable testing methodology at the pilot- and laboratory-scale. Anaerobic digestion systems have a variety of configurations, including the continuously stirred tank reactor (CSTR), plug flow (PF), and anaerobic sequencing batch reactor (ASBR) configurations. The CSTR is frequently used in research due to its simplicity in design and operation, but also for its advantages in experimentation. Compared to other configurations, the CSTR provides greater uniformity of system parameters, such as temperature, mixing, chemical concentration, and substrate concentration. Ultimately, when designing a full-scale reactor, the optimum reactor configuration will depend on the character of a given substrate among many other nontechnical considerations. However, all configurations share fundamental design features and operating parameters that render the CSTR appropriate for most preliminary assessments. If researchers and engineers use an influent stream with relatively high concentrations of solids, then lab-scale bioreactor configurations cannot be fed continuously due to plugging problems of lab-scale pumps with solids or settling of solids in tubing. For that scenario with continuous mixing requirements, lab-scale bioreactors are fed periodically and we refer to such configurations as continuously stirred anaerobic digesters (CSADs). This article presents a general methodology for constructing, inoculating, operating, and monitoring a CSAD system for the purpose of testing the suitability of a given organic substrate for long-term anaerobic digestion. The construction section of this article will cover building the lab-scale reactor system. The inoculation section will explain how to create an anaerobic environment suitable for seeding with an active methanogenic inoculum. The operating section will cover operation, maintenance, and troubleshooting. The monitoring section will introduce testing protocols using standard analyses. The use of these measures is necessary for reliable experimental assessments of substrate suitability for AD. This protocol should provide greater protection against a common mistake made in AD studies, which is to conclude that reactor failure was caused by the substrate in use, when really it was improper user operation.

Assessing and Addressing Students' Scientific Literacy Needs in Physical Geology

NASA Astrophysics Data System (ADS)

Campbell-Stone, E. A.; Myers, J. D.

2005-12-01

Exacting excellence equally from university students around the globe can be accomplished by providing all students with necessary background tools to achieve mastery of their courses, even if those tools are not part of normal content. As instructors we hope to see our students grasp the substance of our courses, make mental connections between course material and practical applications, and use this knowledge to make informed decisions as citizens. Yet many educators have found that students enter university-level introductory courses in mathematics, science and engineering without adequate academic preparation. As part of a FIPSE-funded project at the University of Wyoming, the instructors of the Physical Geology course have taken a new approach to tackling the problem of lack of scientific/mathematic skills in incoming students. Instead of assuming that students should already know or will learn these skills on their own, they assess students' needs and provide them the opportunity to master scientific literacies as they learn geologic content. In the introductory geology course, instructors identified two categories of literacies, or basic skills that are necessary for academic success and citizen participation. Fundamental literacies include performing simple quantitative calculations, making qualitative assessments, and reading and analyzing tables and graphs. Technical literacies are those specific to understanding geology, and comprise the ability to read maps, visualize changes through time, and conceptualize in three dimensions. Because these skills are most easily taught in lab, the in-house lab manual was rewritten to be both literacy- and content-based. Early labs include simple exercises addressing literacies in the context of geological science, and each subsequent lab repeats exposure to literacies, but at increasing levels of difficulty. Resources available to assist students with literacy mastery include individual instruction, a detailed appendix to the lab manual explaining simple tasks such as converting units, and web-based resources. To document the progress of this program, students take pre- and post-course surveys assessing their grasp of the literacies. The surveys gather data on demographics, background, level of interest, level of confidence, understanding, and willingness to complete additional problem sets. This information has been integral in identifying areas of greatest weakness, least interest, and in gauging how backgrounds, expectations, and students' confidence affect their performance.

Chemical Analysis of Drinking Water Concentrates in the Four Lab Study

EPA Science Inventory

The purpose of the Four Lab study was to evaluate potential health effects from exposure to disinfection by-products (DBPs). Unchlorinated water taken from a full-scale drinking water treatment plant was concentrated and chlorinated to form DBPs. Both the unchlorinated (control...

Task driven optimal leg trajectories in insect-scale legged microrobots

NASA Astrophysics Data System (ADS)

Doshi, Neel; Goldberg, Benjamin; Jayaram, Kaushik; Wood, Robert

Origami inspired layered manufacturing techniques and 3D-printing have enabled the development of highly articulated legged robots at the insect-scale, including the 1.43g Harvard Ambulatory MicroRobot (HAMR). Research on these platforms has expanded its focus from manufacturing aspects to include design optimization and control for application-driven tasks. Consequently, the choice of gait selection, body morphology, leg trajectory, foot design, etc. have become areas of active research. HAMR has two controlled degrees-of-freedom per leg, making it an ideal candidate for exploring leg trajectory. We will discuss our work towards optimizing HAMR's leg trajectories for two different tasks: climbing using electroadhesives and level ground running (5-10 BL/s). These tasks demonstrate the ability of single platform to adapt to vastly different locomotive scenarios: quasi-static climbing with controlled ground contact, and dynamic running with un-controlled ground contact. We will utilize trajectory optimization methods informed by existing models and experimental studies to determine leg trajectories for each task. We also plan to discuss how task specifications and choice of objective function have contributed to the shape of these optimal leg trajectories.

Cloudbursting - Solving the 3-body problem

NASA Astrophysics Data System (ADS)

Chang, G.; Heistand, S.; Vakhnin, A.; Huang, T.; Zimdars, P.; Hua, H.; Hood, R.; Koenig, J.; Mehrotra, P.; Little, M. M.; Law, E.

2014-12-01

Many science projects in the future will be accomplished through collaboration among 2 or more NASA centers along with, potentially, external scientists. Science teams will be composed of more geographically dispersed individuals and groups. However, the current computing environment does not make this easy and seamless. By being able to share computing resources among members of a multi-center team working on a science/ engineering project, limited pre-competition funds could be more efficiently applied and technical work could be conducted more effectively with less time spent moving data or waiting for computing resources to free up. Based on the work from an NASA CIO IT Labs task, this presentation will highlight our prototype work in identifying the feasibility and identify the obstacles, both technical and management, to perform "Cloudbursting" among private clouds located at three different centers. We will demonstrate the use of private cloud computing infrastructure at the Jet Propulsion Laboratory, Langley Research Center, and Ames Research Center to provide elastic computation to each other to perform parallel Earth Science data imaging. We leverage elastic load balancing and auto-scaling features at each data center so that each location can independently define how many resources to allocate to a particular job that was "bursted" from another data center and demonstrate that compute capacity scales up and down with the job. We will also discuss future work in the area, which could include the use of cloud infrastructure from different cloud framework providers as well as other cloud service providers.

Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

NASA Technical Reports Server (NTRS)

Garofalo, Anthony A.

2013-01-01

The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

Fluid Vessel Quantity Using Non-invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

NASA Technical Reports Server (NTRS)

Garofalo, Anthony A

2013-01-01

The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

Single-pilot workload management in entry-level jets.

DOT National Transportation Integrated Search

2013-09-01

Researchers from the NASA Ames Flight Cognition Lab and the FAAs Flight Deck Human Factors Research Laboratory at the Civil Aerospace Medical Institute (CAMI) examined task and workload management by single pilots in Very Light Jets (VLJs), also c...

An optical clock to go

NASA Astrophysics Data System (ADS)

Ludlow, Andrew D.

2018-05-01

Bringing next-generation atomic clocks out of the lab is not an easy task, but doing so will unlock many new possibilities. As a crucial first step, a portable atomic clock has now been deployed for relativistic geodesy measurements in the Alps.

Research project management 101: insiders' tips from Early Career Scientists

NASA Astrophysics Data System (ADS)

Cristini, Luisa; Pabortsava, Katsiaryna; Stichel, Torben

2016-04-01

From the very beginning of their career, it is important for Early Career Scientists (ECS) to develop project management skills to be able to organise their research efficiently. ECS are often in charge of specific tasks within their projects or for their teams. However, without specific training or tools, the successful completion of these assignments will depend entirely on the organisational skills of individual researchers. ECS are thus facing "sink-or-swim" situations, which can be either instructive or disastrous for their projects. Here we provide experience-based tips from fellow ECS that can help manage various project activities, including: 1. Communication with supervisors and peers 2. Lab management 3. Field trips (e.g., oceanographic campaigns) 4. Internships and collaborations with other institutions 5. Literature/background research 6. Conference convening These are potential "life buoys" for ECS, which will help them to carry out these tasks efficiently and successfully.

The relationship between joint attention and theory of mind in neurotypical adults.

PubMed

Shaw, Jordan A; Bryant, Lauren K; Malle, Bertram F; Povinelli, Daniel J; Pruett, John R

2017-05-01

Joint attention (JA) is hypothesized to have a close relationship with developing theory of mind (ToM) capabilities. We tested the co-occurrence of ToM and JA in social interactions between adults with no reported history of psychiatric illness or neurodevelopmental disorders. Participants engaged in an experimental task that encouraged nonverbal communication, including JA, and also ToM activity. We adapted an in-lab variant of experience sampling methods (Bryant et al., 2013) to measure ToM during JA based on participants' subjective reports of their thoughts while performing the task. This experiment successfully elicited instances of JA in 17/20 dyads. We compared participants' thought contents during episodes of JA and non-JA. Our results suggest that, in adults, JA and ToM may occur independently. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Results from teleoperated free-flying spacecraft simulations in the Martin Marietta space operations simulator lab

NASA Technical Reports Server (NTRS)

Hartley, Craig S.

1990-01-01

To augment the capabilities of the Space Transportation System, NASA has funded studies and developed programs aimed at developing reusable, remotely piloted spacecraft and satellite servicing systems capable of delivering, retrieving, and servicing payloads at altitudes and inclinations beyond the reach of the present Shuttle Orbiters. Since the mid 1970's, researchers at the Martin Marietta Astronautics Group Space Operations Simulation (SOS) Laboratory have been engaged in investigations of remotely piloted and supervised autonomous spacecraft operations. These investigations were based on high fidelity, real-time simulations and have covered a wide range of human factors issues related to controllability. Among these are: (1) mission conditions, including thruster plume impingements and signal time delays; (2) vehicle performance variables, including control authority, control harmony, minimum impulse, and cross coupling of accelerations; (3) maneuvering task requirements such as target distance and dynamics; (4) control parameters including various control modes and rate/displacement deadbands; and (5) display parameters involving camera placement and function, visual aids, and presentation of operational feedback from the spacecraft. This presentation includes a brief description of the capabilities of the SOS Lab to simulate real-time free-flyer operations using live video, advanced technology ground and on-orbit workstations, and sophisticated computer models of on-orbit spacecraft behavior. Sample results from human factors studies in the five categories cited above are provided.

Lessons learned from implementing a national infrastructure in Sweden for storage and analysis of next-generation sequencing data

PubMed Central

2013-01-01

Analyzing and storing data and results from next-generation sequencing (NGS) experiments is a challenging task, hampered by ever-increasing data volumes and frequent updates of analysis methods and tools. Storage and computation have grown beyond the capacity of personal computers and there is a need for suitable e-infrastructures for processing. Here we describe UPPNEX, an implementation of such an infrastructure, tailored to the needs of data storage and analysis of NGS data in Sweden serving various labs and multiple instruments from the major sequencing technology platforms. UPPNEX comprises resources for high-performance computing, large-scale and high-availability storage, an extensive bioinformatics software suite, up-to-date reference genomes and annotations, a support function with system and application experts as well as a web portal and support ticket system. UPPNEX applications are numerous and diverse, and include whole genome-, de novo- and exome sequencing, targeted resequencing, SNP discovery, RNASeq, and methylation analysis. There are over 300 projects that utilize UPPNEX and include large undertakings such as the sequencing of the flycatcher and Norwegian spruce. We describe the strategic decisions made when investing in hardware, setting up maintenance and support, allocating resources, and illustrate major challenges such as managing data growth. We conclude with summarizing our experiences and observations with UPPNEX to date, providing insights into the successful and less successful decisions made. PMID:23800020

Preparing Teachers to Support the Development of Climate Literate Students

NASA Astrophysics Data System (ADS)

Haddad, N.; Ledley, T. S.; Ellins, K. K.; Bardar, E. W.; Youngman, E.; Dunlap, C.; Lockwood, J.; Mote, A. S.; McNeal, K.; Libarkin, J. C.; Lynds, S. E.; Gold, A. U.

2014-12-01

The EarthLabs climate project includes curriculum development, teacher professional development, teacher leadership development, and research on student learning, all directed at increasing high school teachers' and students' understanding of the factors that shape our planet's climate. The project has developed four new modules which focus on climate literacy and which are part of the larger Web based EarthLabs collection of Earth science modules. Climate related themes highlighted in the new modules include the Earth system with its positive and negative feedback loops; the range of temporal and spatial scales at which climate, weather, and other Earth system processes occur; and the recurring question, "How do we know what we know about Earth's past and present climate?" which addresses proxy data and scientific instrumentation. EarthLabs climate modules use two central strategies to help students navigate the multiple challenges inherent in understanding climate science. The first is to actively engage students with the content by using a variety of learning modes, and by allowing students to pace themselves through interactive visualizations that address particularly challenging content. The second strategy, which is the focus of this presentation, is to support teachers in a subject area where few have substantive content knowledge or technical skills. Teachers who grasp the processes and interactions that give Earth its climate and the technical skills to engage with relevant data and visualizations are more likely to be successful in supporting students' understanding of climate's complexities. This presentation will briefly introduce the EarthLabs project and will describe the steps the project takes to prepare climate literate teachers, including Web based resources, teacher workshops, and the development of a cadre of teacher leaders who are prepared to continue leading the workshops after project funding ends.

Comparative efficacy of new interfaces for intra-procedural imaging review: the Microsoft Kinect, Hillcrest Labs Loop Pointer, and the Apple iPad.

PubMed

Chao, Cherng; Tan, Justin; Castillo, Edward M; Zawaideh, Mazen; Roberts, Anne C; Kinney, Thomas B

2014-08-01

We adapted and evaluated the Microsoft Kinect (touchless interface), Hillcrest Labs Loop Pointer (gyroscopic mouse), and the Apple iPad (multi-touch tablet) for intra-procedural imaging review efficacy in a simulation using MIM Software DICOM viewers. Using each device, 29 radiologists executed five basic interactions to complete the overall task of measuring an 8.1-cm hepatic lesion: scroll, window, zoom, pan, and measure. For each interaction, participants assessed the devices on a 3-point subjective scale (3 = highest usability score). The five individual scores were summed to calculate a subjective composite usability score (max 15 points). Overall task time to completion was recorded. Each user also assessed each device for its potential to jeopardize a sterile field. The composite usability scores were as follows: Kinect 9.9 (out of 15.0; SD = 2.8), Loop Pointer 12.9 (SD = 13.5), and iPad 13.5 (SD = 1.8). Mean task completion times were as follows: Kinect 156.7 s (SD = 86.5), Loop Pointer 51.5 s (SD = 30.6), and iPad 41.1 s (SD = 25.3). The mean hepatic lesion measurements were as follows: Kinect was 7.3 cm (SD = 0.9), Loop Pointer 7.8 cm (SD = 1.1), and iPad 8.2 cm (SD = 1.2). The mean deviations from true hepatic lesion measurement were as follows: Kinect 1.0 cm and for both the Loop Pointer and iPad, 0.9 cm (SD = 0.7). The Kinect had the least and iPad had the most subjective concern for compromising the sterile field. A new intra-operative imaging review interface may be near. Most surveyed foresee these devices as useful in procedures, and most do not anticipate problems with a sterile field. An ideal device would combine iPad's usability and accuracy with the Kinect's touchless aspect.

Determination of pore-scale hydrate phase equilibria in sediments using lab-on-a-chip technology.

PubMed

Almenningen, Stian; Flatlandsmo, Josef; Kovscek, Anthony R; Ersland, Geir; Fernø, Martin A

2017-11-21

We present an experimental protocol for fast determination of hydrate stability in porous media for a range of pressure and temperature (P, T) conditions. Using a lab-on-a-chip approach, we gain direct optical access to dynamic pore-scale hydrate formation and dissociation events to study the hydrate phase equilibria in sediments. Optical pore-scale observations of phase behavior reproduce the theoretical hydrate stability line with methane gas and distilled water, and demonstrate the accuracy of the new method. The procedure is applicable for any kind of hydrate transitions in sediments, and may be used to map gas hydrate stability zones in nature.

The Influence of Process Equipment on the Properties of Suspension Plasma Sprayed Yttria-Stabilized Zirconia Coatings

NASA Astrophysics Data System (ADS)

Marr, Michael; Waldbillig, David; Kesler, Olivera

2013-03-01

Suspension plasma-sprayed YSZ coatings were deposited at lab-scale and production-type facilities to investigate the effect of process equipment on coating properties. The target application for these coatings is solid oxide fuel cell (SOFC) electrolytes; hence, dense microstructures with low permeability values were preferred. Both facilities had the same torch but different suspension feeding systems, torch robots, and substrate holders. The lab-scale facility had higher torch-substrate relative speeds compared with the production-type facility. On porous stainless steel substrates, permeabilities and microstructures were comparable for coatings from both facilities, and no segmentation cracks were observed. Coating permeability was further reduced by increasing substrate temperatures during deposition or reducing suspension feed rates. On SOFC cathode substrates, coatings made in the production-type facility had higher permeabilities and more segmentation cracks compared with coatings made in the lab-scale facility. Increased cracking in coatings from the production-type facility was likely caused mainly by its lower torch-substrate relative speed.

Interfacial film formation: influence on oil spreading rates in lab basin tests and dispersant effectiveness testing in a wave tank.

PubMed

King, Thomas L; Clyburne, Jason A C; Lee, Kenneth; Robinson, Brian J

2013-06-15

Test facilities such as lab basins and wave tanks are essential when evaluating the use of chemical dispersants to treat oil spills at sea. However, these test facilities have boundaries (walls) that provide an ideal environment for surface (interfacial) film formation on seawater. Surface films may form from surfactants naturally present in crude oil as well as dispersant drift/overspray when applied to an oil spill. The objective of this study was to examine the impact of surface film formation on oil spreading rates in a small scale lab basin and on dispersant effectiveness conducted in a large scale wave tank. The process of crude oil spreading on the surface of the basin seawater was influenced in the presence of a surface film as shown using a 1st order kinetic model. In addition, interfacial film formation can greatly influence chemically dispersed crude oil in a large scale dynamic wave tank. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Your brain on bikes: P3, MMN/N2b, and baseline noise while pedaling a stationary bike.

PubMed

Scanlon, Joanna E M; Sieben, Alex J; Holyk, Kevin R; Mathewson, Kyle E

2017-06-01

Increasingly, there is a trend to measure brain activity in more ecologically realistic scenarios. Normally, the confines of the laboratory and sedentary tasks mitigate sources of electrical noise on EEG measurement. Moving EEG outside of the lab requires understanding of the impact of complex movements and activities on traditional EEG and ERP measures. Here, we recorded EEG with active electrodes while participants were either riding or sitting on a stationary bike in an electrical and sound-attenuated chamber in the lab. Participants performed an auditory oddball task, pressing a button when they detected rare target tones in a series of standard frequent tones. We quantified both the levels of spectral, single-trial baseline, and ERP baseline noise, as well as classic MMN/N2b and P3 ERP components measured during both biking and sitting still. We observed slight increases in posterior high frequency noise in the spectra, and increased noise in the baseline period during biking. However, morphologically and topographically similar MMN/N2b and P3 components were measured reliably while both biking and sitting. A quantification of the power to reliably measure ERPs as a function of the number of trials revealed slight increases in the number of trials needed during biking to achieve the same level of power. Taken in sum, our results confirm that classic ERPs can be measured reliably during biking activities in the lab. Future directions will employ these techniques outside the lab in ecologically valid situations. © 2017 Society for Psychophysiological Research.

Fast Realistic MRI Simulations Based on Generalized Multi-Pool Exchange Tissue Model.

PubMed

Liu, Fang; Velikina, Julia V; Block, Walter F; Kijowski, Richard; Samsonov, Alexey A

2017-02-01

We present MRiLab, a new comprehensive simulator for large-scale realistic MRI simulations on a regular PC equipped with a modern graphical processing unit (GPU). MRiLab combines realistic tissue modeling with numerical virtualization of an MRI system and scanning experiment to enable assessment of a broad range of MRI approaches including advanced quantitative MRI methods inferring microstructure on a sub-voxel level. A flexible representation of tissue microstructure is achieved in MRiLab by employing the generalized tissue model with multiple exchanging water and macromolecular proton pools rather than a system of independent proton isochromats typically used in previous simulators. The computational power needed for simulation of the biologically relevant tissue models in large 3D objects is gained using parallelized execution on GPU. Three simulated and one actual MRI experiments were performed to demonstrate the ability of the new simulator to accommodate a wide variety of voxel composition scenarios and demonstrate detrimental effects of simplified treatment of tissue micro-organization adapted in previous simulators. GPU execution allowed  ∼ 200× improvement in computational speed over standard CPU. As a cross-platform, open-source, extensible environment for customizing virtual MRI experiments, MRiLab streamlines the development of new MRI methods, especially those aiming to infer quantitatively tissue composition and microstructure.

Fast Realistic MRI Simulations Based on Generalized Multi-Pool Exchange Tissue Model

PubMed Central

Velikina, Julia V.; Block, Walter F.; Kijowski, Richard; Samsonov, Alexey A.

2017-01-01

We present MRiLab, a new comprehensive simulator for large-scale realistic MRI simulations on a regular PC equipped with a modern graphical processing unit (GPU). MRiLab combines realistic tissue modeling with numerical virtualization of an MRI system and scanning experiment to enable assessment of a broad range of MRI approaches including advanced quantitative MRI methods inferring microstructure on a sub-voxel level. A flexibl representation of tissue microstructure is achieved in MRiLab by employing the generalized tissue model with multiple exchanging water and macromolecular proton pools rather than a system of independent proton isochromats typically used in previous simulators. The computational power needed for simulation of the biologically relevant tissue models in large 3D objects is gained using parallelized execution on GPU. Three simulated and one actual MRI experiments were performed to demonstrate the ability of the new simulator to accommodate a wide variety of voxel composition scenarios and demonstrate detrimental effects of simplifie treatment of tissue micro-organization adapted in previous simulators. GPU execution allowed ∼200× improvement in computational speed over standard CPU. As a cross-platform, open-source, extensible environment for customizing virtual MRI experiments, MRiLab streamlines the development of new MRI methods, especially those aiming to infer quantitatively tissue composition and microstructure. PMID:28113746

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe

2007-05-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal.more » The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests were completed in 2005 and have been previously reported. This topical report presents the results from the Task 3 full-scale additive tests, conducted at IPL's Petersburg Station Unit 2. The Task 5 full-scale additive tests will be conducted later in calendar year 2007.« less

Fuel-Flexible Gasification-Combustion Technology for Production of H2 and Sequestration-Ready CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Parag Kulkarni; Wei Wei

It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Global Research is developing an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE was awarded a contract frommore » U.S. DOE NETL to develop the UFP technology. Work on the Phase I program started in October 2000, and work on the Phase II effort started in April 2005. In the UFP technology, coal and air are simultaneously converted into separate streams of (1) high-purity hydrogen that can be utilized in fuel cells or turbines, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure vitiated air to produce electricity in a gas turbine. The process produces near-zero emissions with an estimated efficiency higher than IGCC with conventional CO2 separation. The Phase I R&D program established the feasibility of the integrated UFP technology through lab-, bench- and pilot-scale testing and investigated operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The Phase I effort integrated experimental testing, modeling and preliminary economic studies to demonstrate the UFP technology. The Phase II effort will focus on three high-risk areas: economics, sorbent attrition and lifetime, and product gas quality for turbines. The economic analysis will include estimating the capital cost as well as the costs of hydrogen and electricity for a full-scale UFP plant. These costs will be benchmarked with IGCC polygen costs for plants of similar size. Sorbent attrition and lifetime will be addressed via bench-scale experiments that monitor sorbent performance over time and by assessing materials interactions at operating conditions. The product gas from the third reactor (high-temperature vitiated air) will be evaluated to assess the concentration of particulates, pollutants and other impurities relative to the specifications required for gas turbine feed streams. This is the eighteenth quarterly technical progress report for the UFP program, which is supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974) and GE. This report summarizes program accomplishments for the Phase II period starting July 01, 2005 and ending September 30, 2005. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including process modeling, scale-up and economic analysis.« less

Single-pilot workload management in entry-level jets : appendices.

DOT National Transportation Integrated Search

2013-09-01

Researchers from the NASA Ames Flight Cognition Lab and the FAAs Flight Deck Human Factors Research Laboratory at the Civil Aerospace Medical Institute (CAMI) examined task and workload management by single pilots in Very Light Jets (VLJs), also c...

Under New Management

ERIC Educational Resources Information Center

Lum, Lydia

2008-01-01

As the task of running universities becomes increasingly multifaceted, more governing boards are hiring presidents whose career achievements occurred outside of classrooms, labs and think tanks, experts say. Today's presidents must manage multimillion dollar operations while juggling duties as varied as fundraising, legislative relations and…

Inaccuracy of perceived competence ratings is associated with problem behaviors in 5-year-old children.

PubMed

Klaver, Jacqueline M; Palo, Amanda D; DiLalla, Lisabeth F

2014-01-01

The authors examined problem behaviors in preschool children as a function of perceived competence. Prior research has demonstrated a link between inaccuracy of self-perceptions and teacher-reported externalizing behaviors in preschool aged boys. This study extended past research by adding data collected from observed behaviors in a laboratory setting, as well as parent reports of internalizing and externalizing behaviors. Five-year-old children completed the Pictorial Scale of Perceived Competence and Social Acceptance for Young Children (PSPCSA) in the lab, participated in a 10-min puzzle interaction task with their cotwin and mother, and completed a short task assessing cognitive abilities. Children were grouped into 3 self-esteem categories (unrealistically low, realistic, and unrealistically high) based on comparisons of self-reported (PSPCSA) versus actual competencies for maternal acceptance, peer acceptance, and cognitive competence. Results showed that children who overreported their maternal acceptance and peer acceptance had significantly more parent-reported externalizing problems as well as internalizing problems. There were no significant differences in accuracy for cognitive competence. The findings from this study underscore the negative impact of unrealistically high self-appraisal on problem behaviors in young children.

Relations between fine motor skill and parental report of attention in young children with neurofibromatosis type 1.

PubMed

Casnar, Christy L; Janke, Kelly M; van der Fluit, Faye; Brei, Natalie G; Klein-Tasman, Bonita P

2014-01-01

Neurofibromatosis type 1 (NF1) is one of the most common genetic disorders presenting in approximately 1 in 3,500 live births. NF1 is a highly variable condition with a large number of complications. A common complication is neuropsychological problems, including developmental delays and learning difficulties that affect as many as 60% of patients. Research has suggested that school-aged children with NF1 often have poorer fine motor skills and are at greater risk for attention difficulties than the general population. Thirty-eight children with NF1 and 23 unaffected children between the ages of 4 and 6 years, who are enrolled in a study of early development in NF1, were included in the present study. Varying levels of fine motor functioning were examined (simple to complex fine motor tasks). For children with NF1, significant difficulties were demonstrated on lab-based mid-level and complex fine motor tasks, even after controlling for nonverbal reasoning abilities, but not on simple fine motor tasks. Parental report also indicated difficulties in everyday adaptive fine motor functioning. No significant correlations were found between complex fine motor ability and attention difficulties. This study provides much needed descriptive data on the early emergence of fine motor difficulties and attention difficulties in young children with NF1.

Does cognitive reappraisal reduce anxiety? A daily diary study of a micro-intervention with individuals with high social anxiety.

PubMed

Kivity, Yogev; Huppert, Jonathan D

2016-03-01

To examine emotion regulation (ER) among individuals with high (HSA) and low social anxiety (LSA) and the effects of 1 week of practiced cognitive reappraisal using self-report, daily diary measures and lab tasks. HSAs received reappraisal (HSA-R; n = 43) or monitoring (HSA-M; n = 40) instructions. LSAs received monitoring instructions (LSA-M; n = 41). Self-report measures of social anxiety and ER, and a lab task of reappraisal were administered at baseline and after 1 week. Daily diaries of anxiety and ER were also collected. At baseline, HSAs compared with LSAs reported lower self-efficacy of reappraisal and higher frequency and self-efficacy of suppression, but no differences emerged in the reappraisal task. Following the intervention, the HSA-R compared with the HSA-M reported lower symptom severity, greater self-efficacy of reappraisal but equal daily anxiety. HSA-R used reappraisal mostly combined with suppression (74.76% of situations). Post hoc analyses demonstrated that clinical diagnosis, but not severity, moderated the intervention effect. The results demonstrate the efficacy of a short intervention in social anxiety, and provide additional areas of research for improving its treatment. (c) 2016 APA, all rights reserved).

Cognitive and neural plasticity in older adults’ prospective memory following training with the Virtual Week computer game

PubMed Central

Rose, Nathan S.; Rendell, Peter G.; Hering, Alexandra; Kliegel, Matthias; Bidelman, Gavin M.; Craik, Fergus I. M.

2015-01-01

Prospective memory (PM) – the ability to remember and successfully execute our intentions and planned activities – is critical for functional independence and declines with age, yet few studies have attempted to train PM in older adults. We developed a PM training program using the Virtual Week computer game. Trained participants played the game in 12, 1-h sessions over 1 month. Measures of neuropsychological functions, lab-based PM, event-related potentials (ERPs) during performance on a lab-based PM task, instrumental activities of daily living, and real-world PM were assessed before and after training. Performance was compared to both no-contact and active (music training) control groups. PM on the Virtual Week game dramatically improved following training relative to controls, suggesting PM plasticity is preserved in older adults. Relative to control participants, training did not produce reliable transfer to laboratory-based tasks, but was associated with a reduction of an ERP component (sustained negativity over occipito-parietal cortex) associated with processing PM cues, indicative of more automatic PM retrieval. Most importantly, training produced far transfer to real-world outcomes including improvements in performance on real-world PM and activities of daily living. Real-world gains were not observed in either control group. Our findings demonstrate that short-term training with the Virtual Week game produces cognitive and neural plasticity that may result in real-world benefits to supporting functional independence in older adulthood. PMID:26578936

How Do Learning Outcomes, Assessments and Student Engagement in a Fully Online Geoscience Laboratory Compare to Those Of The Original Hands-on Exercise?

NASA Astrophysics Data System (ADS)

Jones, F. M.

2015-12-01

In a third year geoscience elective for BSc majors, we adapted several active f2f learning strategies for an equivalent fully online version of the course. In particular, we converted a hands-on laboratory including analysis and interpretation of hand-specimens, sketching results and peer-to-peer discussion of scientific implications. This study compares learning outcomes in both formats and describes resources that make engaging, effective and efficient learning experiences for large classes in an asynchronous online environment. Our two hypotheses are: 1) a hands-on geology lab exercise can be converted for efficient fully online use without sacrificing feedback and assessment opportunities; 2) students find either the f2f or DE versions equally effective and enjoyable as learning experiences. Key components are an authentic context, interactive resources including sketching, strategies that enable efficient assessment and feedback on solo and group work, and asynchronous yet productive interaction with peers. Students in the f2f class handle real rock and fossil specimens, work with peers in the lab and classroom, and deliver most results including annotated figures on paper. DE students complete identical tasks using interactive high resolution figures and videos of specimens. Solo work is first delivered for automated assessment and feedback, then students engage asynchronously in small groups to improve results and discuss implications. Chronostratigraphy and other interpretations are sketched on prepared template images using a simple open-source sketching app that ensures equal access and consistent results that are efficient to assess by peers and instructors. Learning outcomes based on subsequent quizzes, sketches, and lab results (paper for f2f students and automated data entry for DE students), show that f2f and online students demonstrate knowledge and scientific interpretations of comparable quality. Effective engagement and group work are demonstrated for f2f students using video and survey data, and for DE students using learning management system tracking data and similar survey data. Finally, these initiatives are shown to be scalable to classes of many students by comparing the time required for instructors to run and grade the lab in both settings.

Effects of granular activated carbon on methane removal performance and methanotrophic community of a lab-scale bioreactor.

PubMed

Lee, Eun-Hee; Choi, Sun-Ah; Yi, Taewoo; Kim, Tae Gwan; Lee, Sang-Don; Cho, Kyung-Suk

2015-01-01

Two identical lab-scale bioreactor systems were operated to examine the effects of granular activated carbon (GAC) on methane removal performance and methanotrophic community. Both bioreactor systems removed methane completely at a CH4 loading rate of 71.2 g-CH4·d(-1) for 17 days. However, the methane removal efficiency declined to 88% in the bioreactor without GAC, while the bioreactor amended with GAC showed greater methane removal efficiency of 97% at a CH4 loading rate of 107.5 g-CH4·d(-1). Although quantitative real-time PCR showed that methanotrophic populations were similar levels of 5-10 × 10(8) pmoA gene copy number·VSS(-1) in both systems, GAC addition changed the methanotrophic community composition of the bioreactor systems. Microarray assay revealed that GAC enhanced the type I methanotrophic genera including Methylobacter, Methylomicrobium, and Methylomonas of the system, which suggests that GAC probably provided a favorable environment for type I methanotrophs. These results indicated that GAC is a promising support material in bioreactor systems for CH4 mitigation.

What’s in a Prerequisite? A Mixed-Methods Approach to Identifying the Impact of a Prerequisite Course

PubMed Central

Sato, Brian K.; Lee, Amanda K.; Alam, Usman; Dang, Jennifer V.; Dacanay, Samantha J.; Morgado, Pedro; Pirino, Giorgia; Brunner, Jo Ellen; Castillo, Leanne A.; Chan, Valerie W.; Sandholtz, Judith H.

2017-01-01

Despite the ubiquity of prerequisites in undergraduate science, technology, engineering, and mathematics curricula, there has been minimal effort to assess their value in a data-driven manner. Using both quantitative and qualitative data, we examined the impact of prerequisites in the context of a microbiology lecture and lab course pairing. Through interviews and an online survey, students highlighted a number of positive attributes of prerequisites, including their role in knowledge acquisition, along with negative impacts, such as perhaps needlessly increasing time to degree and adding to the cost of education. We also identified a number of reasons why individuals do or do not enroll in prerequisite courses, many of which were not related to student learning. In our particular curriculum, students did not believe the microbiology lecture course impacted success in the lab, which agrees with our analysis of lab course performance using a previously established “familiarity” scale. These conclusions highlight the importance of soliciting and analyzing student feedback, and triangulating these data with quantitative performance metrics to assess the state of science, technology, engineering, and mathematics curricula. PMID:28232587

Extreme Environments Test Capabilities at NASA GRC for Parker Hannifin Visit

NASA Technical Reports Server (NTRS)

Arnett, Lori

2016-01-01

The presentation includes general description on the following test facilities: Fuel Cell Testing Lab, Structural Dynamics Lab, Thermal Vacuum Test Facilities - including a description of the proposed Kinetic High Altitude Simulator concept, EMI Test Lab, and the Creek Road Cryogenic Complex - specifically the Small Multi-purpose Research Facility (SMiRF) and the Cryogenics Components Lab 7 (CCL-7).

Aviation human-in-the-loop simulation studies : experimental planning, design, and data management.

DOT National Transportation Integrated Search

2014-01-01

Researchers from the NASAAmes Flight Cognition Laband the FAAs Aerospace Human Factors Research Lab at the Civil Aerospace Medical Instituteexamined task and workload management by single pilots in very light jets, also called entry-level jets.Thi...

Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 5 Full-Scale Test Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe; MariJon Owens

2007-12-01

This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from the FGD liquor and bulkmore » solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the additives in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power has provided the Texas lignite/PRB co-fired test site for pilot FGD tests and cost sharing. Southern Company has provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation is providing the TMT-15 additive, and the Nalco Company is providing the Nalco 8034 additive. Both companies are also supplying technical support to the test program as in-kind cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests and the full-scale test using high-sulfur coal were completed in 2005 and 2006 and have been previously reported. This topical report presents the results from the Task 5 full-scale additive tests, conducted at Southern Company's Plant Yates Unit 1. Both additives were tested there.« less

Lab experiments investigating astrophysical jet physics

NASA Astrophysics Data System (ADS)

Bellan, Paul

2014-10-01

Dynamics relevant to astrophysical plasmas is being investigated in lab experiments having similar physics and topology, but much smaller time and space scales. High speed movies and numerical simulations both show that highly collimated MHD-driven plasma flows are a critical feature; these collimated flows can be considered to be a lab version of an astrophysical jet. Having both axial and azimuthal magnetic fields, the jet is effectively an axially lengthening plasma-confining flux tube with embedded helical magnetic field (flux rope). The jet velocity is in good agreement with an MHD acceleration model. Axial stagnation of the jet compresses embedded azimuthal magnetic flux and so results in jet self-collimation. Jets kink when they breach the Kruskal-Shafranov stability limit. The lateral acceleration of a sufficiently strong kink can provide an effective gravity which provides the environment for a spontaneously-developing, fine-scale, extremely fast Rayleigh-Taylor instability that erodes the current channel to be smaller than the ion skin depth. This cascade from the ideal MHD scale of the kink to the non-MHD ion skin depth scale can result in a fast magnetic reconnection whereby the jet breaks off from its source electrode. Supported by USDOE and NSF.

Removal of pharmaceuticals during drinking water treatment.

PubMed

Ternes, Thomas A; Meisenheimer, Martin; McDowell, Derek; Sacher, Frank; Brauch, Heinz-Jürgen; Haist-Gulde, Brigitte; Preuss, Gudrun; Wilme, Uwe; Zulei-Seibert, Ninette

2002-09-01

The elimination of selected pharmaceuticals (bezafibrate, clofibric acid, carbamazepine, diclofenac) during drinking water treatment processes was investigated at lab and pilot scale and in real waterworks. No significant removal of pharmaceuticals was observed in batch experiments with sand under natural aerobic and anoxic conditions, thus indicating low sorption properties and high persistence with nonadapted microorganisms. These results were underscored by the presence of carbamazepine in bank-filtrated water with anaerobic conditions in a waterworks area. Flocculation using iron(III) chloride in lab-scale experiments (Jar test) and investigations in waterworks exhibited no significant elimination of the selected target pharmaceuticals. However, ozonation was in some cases very effective in eliminating these polar compounds. In lab-scale experiments, 0.5 mg/L ozone was shown to reduce the concentrations of diclofenac and carbamazepine by more than 90%, while bezafibrate was eliminated by 50% with a 1.5 mg/L ozone dose. Clofibric acid was stable even at 3 mg/L ozone. Under waterworks conditions, similar removal efficiencies were observed. In addition to ozonation, filtration with granular activated carbon (GAC) was very effective in removing pharmaceuticals. Except for clofibric acid, GAC in pilot-scale experiments and waterworks provided a major elimination of the pharmaceuticals under investigation.

Vacuum packing: a model system for laboratory-scale silage fermentations.

PubMed

Johnson, H E; Merry, R J; Davies, D R; Kell, D B; Theodorou, M K; Griffith, G W

2005-01-01

To determine the utility of vacuum-packed polythene bags as a convenient, flexible and cost-effective alternative to fixed volume glass vessels for lab-scale silage studies. Using perennial ryegrass or red clover forage, similar fermentations (as assessed by pH measurement) occurred in glass tube and vacuum-packed silos over a 35-day period. As vacuum-packing devices allow modification of initial packing density, the effect of four different settings (initial packing densities of 0.397, 0.435, 0.492 and 0.534 g cm(-3)) on the silage fermentation over 16 days was examined. Significant differences in pH decline and lactate accumulation were observed at different vacuum settings. Gas accumulation was apparent within all bags and changes in bag volume with time was observed to vary according to initial packing density. Vacuum-packed silos do provide a realistic model system for lab-scale silage fermentations. Use of vacuum-packed silos holds potential for lab-scale evaluations of silage fermentations, allowing higher throughput of samples, more consistent packing as well as the possibility of investigating the effects of different initial packing densities and use of different wrapping materials.

Instrumentation for Performance, Blade Loads and Flowfield Measurement of Novel Hover-Capable Meso-Scale Aerial Platforms

DTIC Science & Technology

2016-12-07

many DoD sponsored MAV projects including one task from ARO and another one as part of Army/Navy/ NASA - sponsored VLRCOE at Maryland all requiring...has undertaken many DoD sponsored MAV projects including one task from ARO and another one as part of Army/Navy/ NASA sponsored Vertical Lift Research

Playing the Simon game: use of the Simon task for investigating human information processing.

PubMed

Proctor, Robert W

2011-02-01

A little more than 40 years ago, J. R. Simon and colleagues introduced what is now called the Simon task, which yielded a correspondence effect known as the Simon effect. In this paper, I set Simon's contribution in the context of research on stimulus-response compatibility. The novel contribution of the Simon task is described, along with foundational findings using the task that Simon and colleagues reported. I acknowledge the significance of Simon's (1990) review chapter in generating my own interests in the Simon task and describe four selected lines of research from my lab that have been a result of those interests. The article concludes with a brief tribute to Simon and his contribution to experimental psychology. Copyright © 2010 Elsevier B.V. All rights reserved.

Carbon Mineralization by Aqueous Precipitation for Beneficial Use of CO2 from Flue Gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Devenney, Martin; Gilliam, Ryan; Seeker, Randy

2013-08-01

The objective of this project is to demonstrate an innovative process to mineralize CO2 from flue gas directly to reactive carbonates and maximize the value and versatility of its beneficial use products. The program scope includes the design, construction, and testing of a CO2 Conversion to Material Products (CCMP) Pilot Demonstration Plant utilizing CO2 from the flue gas of a power production facility in Moss Landing, CA. This topical report covers Subphase 2a which is the design phase of pilot demonstration subsystems. Materials of construction have been selected and proven in both lab scale and prototype testing to be acceptablemore » for the reagent conditions of interest. The target application for the reactive carbonate material has been selected based upon small-scale feasibility studies and the design of a continuous fiber board production line has been completed. The electrochemical cell architecture and components have been selected based upon both lab scale and prototype testing. The appropriate quality control and diagnostic techniques have been developed and tested along with the required instrumentation and controls. Finally the demonstrate site infrastructure, NEPA categorical exclusion, and permitting is all ready for the construction and installation of the new units and upgrades.« less

Towards the Development of a Smart Flying Sensor: Illustration in the Field of Precision Agriculture.

PubMed

Hernandez, Andres; Murcia, Harold; Copot, Cosmin; De Keyser, Robin

2015-07-10

Sensing is an important element to quantify productivity, product quality and to make decisions. Applications, such as mapping, surveillance, exploration and precision agriculture, require a reliable platform for remote sensing. This paper presents the first steps towards the development of a smart flying sensor based on an unmanned aerial vehicle (UAV). The concept of smart remote sensing is illustrated and its performance tested for the task of mapping the volume of grain inside a trailer during forage harvesting. Novelty lies in: (1) the development of a position-estimation method with time delay compensation based on inertial measurement unit (IMU) sensors and image processing; (2) a method to build a 3D map using information obtained from a regular camera; and (3) the design and implementation of a path-following control algorithm using model predictive control (MPC). Experimental results on a lab-scale system validate the effectiveness of the proposed methodology.

Towards the Development of a Smart Flying Sensor: Illustration in the Field of Precision Agriculture

PubMed Central

Hernandez, Andres; Murcia, Harold; Copot, Cosmin; De Keyser, Robin

2015-01-01

Sensing is an important element to quantify productivity, product quality and to make decisions. Applications, such as mapping, surveillance, exploration and precision agriculture, require a reliable platform for remote sensing. This paper presents the first steps towards the development of a smart flying sensor based on an unmanned aerial vehicle (UAV). The concept of smart remote sensing is illustrated and its performance tested for the task of mapping the volume of grain inside a trailer during forage harvesting. Novelty lies in: (1) the development of a position-estimation method with time delay compensation based on inertial measurement unit (IMU) sensors and image processing; (2) a method to build a 3D map using information obtained from a regular camera; and (3) the design and implementation of a path-following control algorithm using model predictive control (MPC). Experimental results on a lab-scale system validate the effectiveness of the proposed methodology. PMID:26184205

Virtual Computing Laboratories: A Case Study with Comparisons to Physical Computing Laboratories

ERIC Educational Resources Information Center

Burd, Stephen D.; Seazzu, Alessandro F.; Conway, Christopher

2009-01-01

Current technology enables schools to provide remote or virtual computing labs that can be implemented in multiple ways ranging from remote access to banks of dedicated workstations to sophisticated access to large-scale servers hosting virtualized workstations. This paper reports on the implementation of a specific lab using remote access to…

Electrospinning-based synthesis of highly ordered mesoporous silica fiber for lab-in-syringe enrichment of plasma peptides.

PubMed

Zhu, Gang-Tian; Li, Xiao-Shui; Fu, Xiao-Meng; Wu, Jian-Yuan; Yuan, Bi-Feng; Feng, Yu-Qi

2012-10-14

Silica fiber with highly ordered mesoporous structure and continuously long fibrous property was synthesized on a large-scale for the first time. It can be applied to the rapid (less than 3 min) and effective enrichment of endogenous peptides with a novel lab-in-syringe approach.

Carbon budgets of biological soil crusts at micro-, meso-, and global scales

USGS Publications Warehouse

Sancho, Leopoldo G; Belnap, Jayne; Colesie, Claudia; Raggio, Jose; Weber, Bettina

2016-01-01

The importance of biocrusts in the ecology of arid lands across all continents is widely recognized. In spite of this broad distribution, contributions of biocrusts to the global biogeochemical cycles have only recently been considered. While these studies opened a new view on the global role of biocrusts, they also clearly revealed the lack of data for many habitats and of overall standards for measurements and analysis. In order to understand carbon cycling in biocrusts and the progress which has been made during the last 15 years, we offer a multi-scale approach covering different climatic regions. We also include a discussion on available measurement techniques at each scale: A micro-scale section focuses on the individual organism level, including modeling based on the combination of field and lab data. The meso-scale section addresses the CO2 exchange of a complete ecosystem or at the community level. Finally, we consider the contribution of biocrusts at a global scale, giving a general perspective of the most relevant findings regarding the role of biological soil crusts in the global terrestrial carbon cycle.

Virtual Reality Simulator Systems in Robotic Surgical Training.

PubMed

Mangano, Alberto; Gheza, Federico; Giulianotti, Pier Cristoforo

2018-06-01

The number of robotic surgical procedures has been increasing worldwide. It is important to maximize the cost-effectiveness of robotic surgical training and safely reduce the time needed for trainees to reach proficiency. The use of preliminary lab training in robotic skills is a good strategy for the rapid acquisition of further, standardized robotic skills. Such training can be done either by using a simulator or by exercises in a dry or wet lab. While the use of an actual robotic surgical system for training may be problematic (high cost, lack of availability), virtual reality (VR) simulators can overcome many of these obstacles. However, there is still a lack of standardization. Although VR training systems have improved, they cannot yet replace experience in a wet lab. In particular, simulated scenarios are not yet close enough to a real operative experience. Indeed, there is a difference between technical skills (i.e., mechanical ability to perform a simulated task) and surgical competence (i.e., ability to perform a real surgical operation). Thus, while a VR simulator can replace a dry lab, it cannot yet replace training in a wet lab or operative training in actual patients. However, in the near future, it is expected that VR surgical simulators will be able to provide total reality simulation and replace training in a wet lab. More research is needed to produce more wide-ranging, trans-specialty robotic curricula.

Advancing the practice of systems engineering at JPL

NASA Technical Reports Server (NTRS)

Jansma, Patti A.; Jones, Ross M.

2006-01-01

In FY 2004, JPL launched an initiative to improve the way it practices systems engineering. The Lab's senior management formed the Systems Engineering Advancement (SEA) Project in order to "significantly advance the practice and organizational capabilities of systems engineering at JPL on flight projects and ground support tasks." The scope of the SEA Project includes the systems engineering work performed in all three dimensions of a program, project, or task: 1. the full life-cycle, i.e., concept through end of operations 2. the full depth, i.e., Program, Project, System, Subsystem, Element (SE Levels 1 to 5) 3. the full technical scope, e.g., the flight, ground and launch systems, avionics, power, propulsion, telecommunications, thermal, etc. The initial focus of their efforts defined the following basic systems engineering functions at JPL: systems architecture, requirements management, interface definition, technical resource management, system design and analysis, system verification and validation, risk management, technical peer reviews, design process management and systems engineering task management, They also developed a list of highly valued personal behaviors of systems engineers, and are working to inculcate those behaviors into members of their systems engineering community. The SEA Project is developing products, services, and training to support managers and practitioners throughout the entire system lifecycle. As these are developed, each one needs to be systematically deployed. Hence, the SEA Project developed a deployment process that includes four aspects: infrastructure and operations, communication and outreach, education and training, and consulting support. In addition, the SEA Project has taken a proactive approach to organizational change management and customer relationship management - both concepts and approaches not usually invoked in an engineering environment. This paper'3 describes JPL's approach to advancing the practice of systems engineering at the Lab. It describes the general approach used and how they addressed the three key aspects of change: people, process and technology. It highlights a list of highly valued personal behaviors of systems engineers, discusses the various products, services and training that were developed, describes the deployment approach used, and concludes with several lessons learned.

Understanding Dynamic Soil Water Repellency and its Hydrological Implications

NASA Astrophysics Data System (ADS)

Beatty, S. M.; Smith, J. E.

2009-05-01

The adverse effects of water repellent soils on vadose zone hydrology are being increasingly identified worldwide in both rural and urban landscapes. Among the affected landscapes are agricultural fields, forests, effluent application sites, golf greens, wetlands, and wildfire sites. In spite of cross-discipline research efforts put forth in recent years, understanding of fundamental parameters controlling soil water behaviour in these systems is lacking. This is due, in part, to inherent complexities of water repellent soil systems and logistical shortcomings of methods commonly used by researchers in-situ and in the lab. As a result, modeling flow in these systems has further proven to be a difficult task. The objectives of our study were 1) to systematically measure and quantify water infiltration and distribution in dynamic water repellent systems and 2) to identify fundamental hydraulic behaviours that lead to the expression of changes in soil water repellency. To achieve this, we combined techniques to elucidate soil- water interactions at a post-wildfire site. Field tests and subsequent lab work reveal essential hydrological information on fire-affected water repellent soils at variable scales and under different burn conditions. Through the use of traditional and newer techniques, our work shows unique and previously unreported behaviour of soil water in these systems. We also address limitations of current field methods used to study repellency and associated infiltration behaviours.

Analysis of the Hexapod Work Space using integration of a CAD/CAE system and the LabVIEW software

NASA Astrophysics Data System (ADS)

Herbuś, K.; Ociepka, P.

2015-11-01

The paper presents the problems related to the integration of a CAD/CAE system with the LabVIEW software. The purpose of the integration is to determine the workspace of a hexapod model basing on a mathematical model describing it motion. In the first stage of the work concerning the integration task the 3D model to simulate movements of a hexapod was elaborated. This phase of the work was done in the “Motion Simulation” module of the CAD/CAE/CAM Siemens NX system. The first step was to define the components of the 3D model in the form of “links”. Individual links were defined according to the nature of the hexapod elements action. In the model prepared for movement simulation were created links corresponding to such elements as: electric actuator, top plate, bottom plate, ball-and-socket joint, toggle joint Phillips. Then were defined the constraints of the “joint” type (e.g.: revolute joint, slider joint, spherical joint) between the created component of the “link” type, so that the computer simulation corresponds to the operation of a real hexapod. The next stage of work included implementing the mathematical model describing the functioning of a hexapod in the LabVIEW software. At this stage, particular attention was paid to determining procedures for integrating the virtual 3D hexapod model with the results of calculations performed in the LabVIEW. The results relate to specific values of the jump of electric actuators depending on the position of the car on the hexapod. The use of integration made it possible to determine the safe operating space of a stationary hexapod taking into consideration the security of a person in the driving simulator designed for the disabled.

Rehabilitation of divided attention after severe traumatic brain injury: a randomised trial.

PubMed

Couillet, Josette; Soury, Stephane; Lebornec, Gaelle; Asloun, Sybille; Joseph, Pierre-Alain; Mazaux, Jean-Michel; Azouvi, Philippe

2010-06-01

Patients with severe traumatic brain injury (TBI) frequently suffer from a difficulty in dealing with two tasks simultaneously. However, there has been little research on the rehabilitation of divided attention. The objective of the present study was to assess the effectiveness of a rehabilitation programme for divided attention after severe TBI. Twelve patients at a subacute/chronic stage after a severe TBI were included. A randomised AB vs. BA cross-over design was used. Training lasted six weeks, with four one-hour sessions per week. It was compared to a non-specific (control) cognitive training. During experimental treatment, patients were trained to perform two concurrent tasks simultaneously. Each one of the two tasks was first trained as a single task, then both tasks were given simultaneously. A progressive hierarchical order of difficulty was used, by progressively increasing task difficulty following each patient's individual improvement. Patients were randomised in two groups: one starting with dual-task training, the other with control training. Outcome measures included target dual-task measures, executive and working memory tasks, non-target tasks, and the Rating Scale of Attentional Behaviour addressing attentional problems in everyday life. Assessment was not blind to treatment condition. A significant training-related effect was found on dual-task measures and on the divided attention item of the Rating Scale of Attentional Behaviour. There was only little effect on executive measures, and no significant effect on non-target measures. These results suggest that training had specific effects on divided attention and helped patients to deal more rapidly and more accurately with dual-task situations.

Environmental Response Laboratory Network (ERLN) Basic Ordering Agreement Fact Sheet

EPA Pesticide Factsheets

Having a standing agreement means that a laboratory has been vetted and has proven capable of providing certain services that meet ERLN standards, and it provides a mechanism for EPA to quickly task a lab to provide supplies/services during an indicent.

Development of flight experiment work performance and workstation interface requirements, part 1. Technical report and appendices A through G

NASA Technical Reports Server (NTRS)

Hatterick, R. G.

1973-01-01

A skill requirement definition method was applied to the problem of determining, at an early stage in system/mission definition, the skills required of on-orbit crew personnel whose activities will be related to the conduct or support of earth-orbital research. The experiment data base was selected from proposed experiments in NASA's earth orbital research and application investigation program as related to space shuttle missions, specifically those being considered for Sortie Lab. Concepts for two integrated workstation consoles for Sortie Lab experiment operations were developed, one each for earth observations and materials sciences payloads, utilizing a common supporting subsystems core console. A comprehensive data base of crew functions, operating environments, task dependencies, task-skills and occupational skills applicable to a representative cross section of earth orbital research experiments is presented. All data has been coded alphanumerically to permit efficient, low cost exercise and application of the data through automatic data processing in the future.

Virtual reality applications in robotic simulations

NASA Technical Reports Server (NTRS)

Homan, David J.; Gott, Charles J.; Goza, S. Michael

1994-01-01

Virtual reality (VR) provides a means to practice integrated extravehicular activities (EVA)/remote manipulator system (RMS) operations in the on-orbit configuration with no discomfort or risk to crewmembers. VR afforded the STS-61 crew the luxury of practicing the integrated EVA/RMS operations in an on-orbit configuration prior to the actual flight. The VR simulation was developed by the Automation and Robotics Division's Telepresence/Virtual Reality Lab and Integrated Graphics, Operations, and Analysis Lab (IGOAL) at JSC. The RMS Part Task Trainer (PTT) was developed by the IGOAL for RMS training in 1988 as a fully functional, kinematic simulation of the shuttle RMS and served as the RMS portion of the integrated VR simulation. Because the EVA crewmember could get a realistic view of the shuttle and payload bay in the VR simulation, he/she could explore different positions and views to determine the best method for performing a specific task, thus greatly increasing the efficiency of use of the neutral buoyancy facilities.

The relationship between attention and deferred imitation in 12-month-old infants.

PubMed

Zmyj, Norbert; Schölmerich, Axel; Daum, Moritz M

2017-08-01

Imitation is a frequent behavior in the first years of life, and serves both a social function (e.g., to interact with others) and a cognitive function (e.g., to learn a new skill). Infants differ in their temperament, and temperament might be related to the dominance of one function of imitation. In this study, we investigated whether temperament and deferred imitation are related in 12-month-old infants. Temperament was measured via the Infant Behavior Questionnaire Revised (IBQ-R) and parts of the Laboratory Temperament Assessment Battery (Lab-TAB). Deferred imitation was measured via the Frankfurt Imitation Test for 12-month-olds (FIT-12). Regression analyses revealed that the duration of orienting (IBQ-R) and the latency of the first look away in the Task Orientation task (Lab-TAB) predicted the infants' imitation score. These results suggest that attention-related processes may play a major role when infants start to imitate. Copyright © 2017 Elsevier Inc. All rights reserved.

Nanocellulose as Material Building Block for Energy and Flexible Electronics

NASA Astrophysics Data System (ADS)

Hu, Liangbing

2014-03-01

In this talk, I will discuss the fabrications, properties and device applications of functional nanostructured paper based on nanocellulose. Nanostructures with tunable optical, electrical, ionic and mechanical properties will be discussed. Lab-scale demonstration devices, including low-cost Na-ion batteries, microbial fuel cells, solar cells, transparent transistors, actuators and touch screens will be briefly mentioned. These studies show that nanocellulose is a promising green material for electronics and energy devices.

Quality by design: scale-up of freeze-drying cycles in pharmaceutical industry.

PubMed

Pisano, Roberto; Fissore, Davide; Barresi, Antonello A; Rastelli, Massimo

2013-09-01

This paper shows the application of mathematical modeling to scale-up a cycle developed with lab-scale equipment on two different production units. The above method is based on a simplified model of the process parameterized with experimentally determined heat and mass transfer coefficients. In this study, the overall heat transfer coefficient between product and shelf was determined by using the gravimetric procedure, while the dried product resistance to vapor flow was determined through the pressure rise test technique. Once model parameters were determined, the freeze-drying cycle of a parenteral product was developed via dynamic design space for a lab-scale unit. Then, mathematical modeling was used to scale-up the above cycle in the production equipment. In this way, appropriate values were determined for processing conditions, which allow the replication, in the industrial unit, of the product dynamics observed in the small scale freeze-dryer. This study also showed how inter-vial variability, as well as model parameter uncertainty, can be taken into account during scale-up calculations.

Operational experience and design recommendations for teleoperated flight hardware

NASA Technical Reports Server (NTRS)

Burgess, T. W.; Kuban, D. P.; Hankins, W. W.; Mixon, R. W.

1988-01-01

Teleoperation (remote manipulation) will someday supplement/minimize astronaut extravehicular activity in space to perform such tasks as satellite servicing and repair, and space station construction and servicing. This technology is being investigated by NASA with teleoperation of two space-related tasks having been demonstrated at the Oak Ridge National Lab. The teleoperator experiments are discussed and the results of these experiments are summarized. The related equipment design recommendations are also presented. In addition, a general discussion of equipment design for teleoperation is also presented.

Glossary of testing terminology for rechargeable batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, P.C.

1988-10-01

The Battery Test Working Task Force was formed in 1983 for the purpose of coordinating the evaluation of development rechargeable batteries by DOE-funded labs. The Task Force developed this glossary of testing terminology to improve the accuracy of communication and to permit meaningful comparisons of test results. It consists of a section of technical terms and a separate section of programmatic phrases and acronyms. The glossary emphasizes terms related to electric vehicle batteries due to the significant development and testing activities in this area. 8 refs.

Recirculation of reverse osmosis concentrate in lab-scale anaerobic and aerobic landfill simulation reactors.

PubMed

Morello, Luca; Cossu, Raffaello; Raga, Roberto; Pivato, Alberto; Lavagnolo, Maria Cristina

2016-10-01

Leachate treatment is a major issue in the context of landfill management, particularly in view of the consistent changes manifested over time in the quality and quantity of leachate produced, linked to both waste and landfill characteristics, which renders the procedure technically difficult and expensive. Leachate recirculation may afford a series of potential advantages, including improvement of leachate quality, enhancement of gas production, acceleration of biochemical processes, control of moisture content, as well as nutrients and microbe migration within the landfill. Recirculation of the products of leachate treatment, such as reverse osmosis (RO) concentrate, is a less common practice, with widespread controversy relating to its suitability, potential impacts on landfill management and future gaseous and leachable emissions. Scientific literature provides the results of only a few full-scale applications of concentrate recirculation. In some cases, an increase of COD and ammonium nitrogen in leachate was observed, coupled with an increase of salinity; which, additionally, might negatively affect performance of the RO plant itself. In other cases, not only did leachate production not increase significantly but the characteristics of leachate extracted from the well closest to the re-injection point also remained unchanged. This paper presents the results of lab-scale tests conducted in landfill simulation reactors, in which the effects of injection of municipal solid waste (MSW) landfill leachate RO concentrate were evaluated. Six reactors were managed with different weekly concentrate inputs, under both anaerobic and aerobic conditions, with the aim of investigating the short and long-term effects of this practice on landfill emissions. Lab-scale tests resulted in a more reliable identification of compound accumulation and kinetic changes than full-scale applications, further enhancing the development of a mass balance in which gaseous emissions and waste characteristics were also taken into consideration. Results showed that RO concentrate recirculation did not produce consistent changes in COD emissions and methane production. Simultaneously, ammonium ion showed a consistent increase in leachate (more than 25%) in anaerobic reactors, free ammonia gaseous emissions doubled with concentrate injection, while chloride resulted accumulated inside the reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Model-based strategy for cell culture seed train layout verified at lab scale.

PubMed

Kern, Simon; Platas-Barradas, Oscar; Pörtner, Ralf; Frahm, Björn

2016-08-01

Cell culture seed trains-the generation of a sufficient viable cell number for the inoculation of the production scale bioreactor, starting from incubator scale-are time- and cost-intensive. Accordingly, a seed train offers potential for optimization regarding its layout and the corresponding proceedings. A tool has been developed to determine the optimal points in time for cell passaging from one scale into the next and it has been applied to two different cell lines at lab scale, AGE1.HN AAT and CHO-K1. For evaluation, experimental seed train realization has been evaluated in comparison to its layout. In case of the AGE1.HN AAT cell line, the results have also been compared to the formerly manually designed seed train. The tool provides the same seed train layout based on the data of only two batches.

Lab meets real life: A laboratory assessment of spontaneous thought and its ecological validity

PubMed Central

Welz, Annett; Reinhard, Iris; Alpers, Georg W.

2017-01-01

People’s minds frequently wander towards self-generated thoughts, which are unrelated to external stimuli or demands. These phenomena, referred to as “spontaneous thought” (ST) and “mind wandering” (MW), have previously been linked with both costs and benefits. Current assessments of ST and MW have predominantly been conducted in the laboratory, whereas studies on the ecological validity of such lab-related constructs and their interrelations are rare. The current study examined the stability of ST dimensions assessed in the lab and their predictive value with respect to MW, repetitive negative thought (uncontrollable rumination, RUM), and affect in daily life. Forty-three university students were assessed with the Amsterdam Resting State Questionnaire (2nd version) to assess ten ST dimensions during the resting state in two laboratory sessions, which were separated by five days of electronic ambulatory assessment (AA). During AA, individuals indicated the intensity of MW and RUM, as well as of positive and negative affect in daily life ten times a day. ST dimensions measured in the lab were moderately stable across one week. Five out of ten ST lab dimensions were predicted by mental health-related symptoms or by dispositional cognitive traits. Hierarchical linear models revealed that a number of ST lab dimensions predicted cognitive and affective states in daily life. Mediation analyses showed that RUM, but not MW per se, accounted for the relationship between specific ST lab dimensions and mood in daily life. By using a simple resting state task, we could demonstrate that a number of lab dimensions of spontaneous thought are moderately stable, are predicted by mental health symptoms and cognitive traits, and show plausible associations with categories of self-generated thought and mood in daily life. PMID:28910351

Institutional profile: the national Swedish academic drug discovery & development platform at SciLifeLab

PubMed Central

Arvidsson, Per I; Sandberg, Kristian; Sakariassen, Kjell S

2017-01-01

The Science for Life Laboratory Drug Discovery and Development Platform (SciLifeLab DDD) was established in Stockholm and Uppsala, Sweden, in 2014. It is one of ten platforms of the Swedish national SciLifeLab which support projects run by Swedish academic researchers with large-scale technologies for molecular biosciences with a focus on health and environment. SciLifeLab was created by the coordinated effort of four universities in Stockholm and Uppsala: Stockholm University, Karolinska Institutet, KTH Royal Institute of Technology and Uppsala University, and has recently expanded to other Swedish university locations. The primary goal of the SciLifeLab DDD is to support selected academic discovery and development research projects with tools and resources to discover novel lead therapeutics, either molecules or human antibodies. Intellectual property developed with the help of SciLifeLab DDD is wholly owned by the academic research group. The bulk of SciLifeLab DDD's research and service activities are funded from the Swedish state, with only consumables paid by the academic research group through individual grants. PMID:28670468

Institutional profile: the national Swedish academic drug discovery & development platform at SciLifeLab.

PubMed

Arvidsson, Per I; Sandberg, Kristian; Sakariassen, Kjell S

2017-06-01

The Science for Life Laboratory Drug Discovery and Development Platform (SciLifeLab DDD) was established in Stockholm and Uppsala, Sweden, in 2014. It is one of ten platforms of the Swedish national SciLifeLab which support projects run by Swedish academic researchers with large-scale technologies for molecular biosciences with a focus on health and environment. SciLifeLab was created by the coordinated effort of four universities in Stockholm and Uppsala: Stockholm University, Karolinska Institutet, KTH Royal Institute of Technology and Uppsala University, and has recently expanded to other Swedish university locations. The primary goal of the SciLifeLab DDD is to support selected academic discovery and development research projects with tools and resources to discover novel lead therapeutics, either molecules or human antibodies. Intellectual property developed with the help of SciLifeLab DDD is wholly owned by the academic research group. The bulk of SciLifeLab DDD's research and service activities are funded from the Swedish state, with only consumables paid by the academic research group through individual grants.

Boomwhackers and End-Pipe Corrections

NASA Astrophysics Data System (ADS)

Ruiz, Michael J.

2014-02-01

End-pipe corrections seldom come to mind as a suitable topic for an introductory physics lab. Yet, the end-pipe correction formula can be verified in an engaging and inexpensive lab that requires only two supplies: plastic-tube toys called boomwhackers and a meterstick. This article describes a lab activity in which students model data from plastic tubes to arrive at the end-correction formula for an open pipe. Students also learn the basic mathematics behind the musical scale, and come to appreciate the importance of end-pipe physics in the engineering design of toy musical tubes.

Comparison between lab- and full-scale applications of in situ aeration of an old landfill and assessment of long-term emission development after completion.

PubMed

Hrad, Marlies; Gamperling, Oliver; Huber-Humer, Marion

2013-10-01

Sustainable landfilling has become a fundamental objective in many modern waste management concepts. In this context, the in situ aeration of landfills has been recognised for its potential to convert conventional anaerobic landfills into biological stabilised state, whereby both current and potential (long-term) emissions of the landfilled waste are mitigated. In recent years, different in situ aeration concepts have been successfully applied in Europe, North America and Asia, all pursuing different objectives and strategies. In Austria, the first full-scale application of in situ landfill aeration by means of low pressure air injection and simultaneous off-gas collection and treatment was implemented on an old, small municipal solid waste (MSW) landfill (2.6ha) in autumn 2007. Complementary laboratory investigations were conducted with waste samples taken from the landfill site in order to provide more information on the transferability of the results from lab- to full-scale aeration measures. In addition, long-term emission development of the stabilised waste after aeration completion was assessed in an ongoing laboratory experiment. Although the initial waste material was described as mostly stable in terms of the biological parameters gas generation potential over 21days (GP21) and respiration activity over 4days (RA4), the lab-scale experiments indicated that aeration, which led to a significant improvement of leachate quality, was accompanied by further measurable changes in the solid waste material under optimised conditions. Even 75weeks after aeration completion the leachate, as well as gaseous emissions from the stabilised waste material, remained low and stayed below the authorised Austrian discharge limits. However, the application of in situ aeration at the investigated landfill is a factor 10 behind the lab-based predictions after 3years of operation, mainly due to technical limitations in the full-scale operation (e.g. high air flow resistivity due to high water content of waste and temporarily high water levels within the landfill; limited efficiency of the aeration wells). In addition, material preparation (e.g. sieving, sorting and homogenisation) prior to the emplacement in Landfill Simulation Reactors (LSRs) must be considered when transferring results from lab- to full-scale application. Copyright © 2013 Elsevier Ltd. All rights reserved.

The Infant Version of the Laboratory Temperament Assessment Battery (Lab-TAB): Measurement Properties and Implications for Concepts of Temperament

PubMed Central

Planalp, Elizabeth M.; Van Hulle, Carol; Gagne, Jeffrey R.; Goldsmith, H. Hill

2017-01-01

We describe large-sample research using the Infant Laboratory Temperament Assessment Battery (Lab-TAB; Goldsmith and Rothbart, 1996) in 1,076 infants at 6 and 12 months of age. The Lab-TAB was designed to assess temperament dimensions through a series of episodes that mimic everyday situations. Our goal is to provide guidelines for scoring Lab-TAB episodes to derive temperament composites. We also present a set of analyses examining mean differences and stability of temperament in early infancy, gender differences in infant temperament, as well as a validation of Lab-TAB episodes and composites with parent reported Infant Behavior Questionnaire (IBQ; Rothbart, 1981) scales. In general, laboratory observed temperament was only modestly related to parent reported temperament. However, temperament measures were significantly stable across time and several gender differences that align with previous research emerged. In sum, the Lab-TAB usefully assesses individual differences in infant emotionality. PMID:28596748

Gene Expression Analysis: Teaching Students to Do 30,000 Experiments at Once with Microarray

ERIC Educational Resources Information Center

Carvalho, Felicia I.; Johns, Christopher; Gillespie, Marc E.

2012-01-01

Genome scale experiments routinely produce large data sets that require computational analysis, yet there are few student-based labs that illustrate the design and execution of these experiments. In order for students to understand and participate in the genomic world, teaching labs must be available where students generate and analyze large data…

Lab-on-fiber technology: a new vision for chemical and biological sensing.

PubMed

Ricciardi, Armando; Crescitelli, Alessio; Vaiano, Patrizio; Quero, Giuseppe; Consales, Marco; Pisco, Marco; Esposito, Emanuela; Cusano, Andrea

2015-12-21

The integration of microfluidics and photonic biosensors has allowed achievement of several laboratory functions in a single chip, leading to the development of photonic lab-on-a-chip technology. Although a lot of progress has been made to implement such sensors in small and easy-to-use systems, many applications such as point-of-care diagnostics and in vivo biosensing still require a sensor probe able to perform measurements at precise locations that are often hard to reach. The intrinsic property of optical fibers to conduct light to a remote location makes them an ideal platform to meet this demand. The motivation to combine the good performance of photonic biosensors on chips with the unique advantages of optical fibers has thus led to the development of the so-called lab-on-fiber technology. This emerging technology envisages the integration of functionalized materials on micro- and nano-scales (i.e. the labs) with optical fibers to realize miniaturized and advanced all-in-fiber probes, especially useful for (but not limited to) label-free chemical and biological applications. This review presents a broad overview of lab-on-fiber biosensors, with particular reference to lab-on-tip platforms, where the labs are integrated on the optical fiber facet. Light-matter interaction on the fiber tip is achieved through the integration of thin layers of nanoparticles or nanostructures supporting resonant modes, both plasmonic and photonic, highly sensitive to local modifications of the surrounding environment. According to the physical principle that is exploited, different configurations - such as localized plasmon resonance probes, surface enhanced Raman scattering probes and photonic probes - are classified, while various applications are presented in context throughout. For each device, the surface chemistry and the related functionalization protocols are reviewed. Moreover, the implementation strategies and fabrication processes, either based on bottom-up or top-down approaches, are discussed. In conclusion we highlight some of the further development opportunities, including lab-in-a-needle technology, which could have a direct and disruptive impact in localized cancer treatment applications.

Do complaints of everyday cognitive failures in high schizotypy relate to emotional working memory deficits in the lab?

PubMed

Carrigan, Nicole; Barkus, Emma; Ong, Adriel; Wei, Maryann

2017-10-01

Individuals high on schizotypy complain of increased cognitive failures in everyday life. However, the neuropsychological performance of this group does not consistently indicate underlying ability deficits. It is possible that current neuropsychological tests lack ecological validity. Given the increased affective reactivity of high schizotypes, they may be more sensitive to emotional content interfering with cognitive ability. This study sought to explore whether an affective n-back working memory task would elicit impaired performance in schizotypy, echoing complaints concerning real world cognition. 127 healthy participants completed self-report measures of schizotypy and cognitive failures and an affective n-back working memory task. This task was varied across three levels of load (1- to 3-back) and four types of stimulus emotion (neutral, fearful, happy, sad). Differences between high (n=39) and low (n=48) schizotypy groups on performance outcomes of hits and false alarms were examined, with emotion and load as within-groups variables. As expected, high schizotypes reported heightened vulnerability to cognitive failures. They also demonstrated a relative working memory impairment for emotional versus neutral stimuli, whereas low schizotypes did not. High schizotypes performed most poorly in response to fearful stimuli. For false alarms, there was an interaction between schizotypy, load, and emotion, such that high schizotypy was associated with deficits in response to fearful stimuli only at higher levels of task difficulty. Inclusion of self-reported cognitive failures did not account for this. These findings suggest that the "gap" between subjective and objective cognition in schizotypy may reflect the heightened emotional demands associated with cognitive functioning in the real world, although other factors also seem to play a role. There is a need to improve the ecological validity of objective assessments, whilst also recognizing that self-reported cognitive failures tap into a range of factors difficult to assess in the lab, including emotion. Cognitive interventions for at-risk individuals will likely be more beneficial if they address emotional processing alongside other aspects of cognition. Copyright © 2017 Elsevier Inc. All rights reserved.

SenseCube—a novel inexpensive wireless multisensor for physics lab experimentations

NASA Astrophysics Data System (ADS)

Mehta, Vedant; Lane, Charles D.

2018-07-01

SenseCube is a multisensor capable of measuring many different real-time events and changes in environment. Most conventional sensors used in introductory-physics labs use their own software and have wires that must be attached to a computer or an alternate device to analyze the data. This makes the standard sensors time consuming, tedious, and space-constricted. SenseCube was developed to overcome these limitations. This research was focused on developing a device that is all-encompassing, cost-effective, wireless, and compact, yet can perform the same tasks as the multiple standard sensors normally used in physics labs. It measures more than twenty distinct types of real-time events and transfers the data via Bluetooth. Both Windows and Mac software were developed so that the data from this device can be retrieved and/or saved on either platform. This paper describes the sensor itself, its development, its capabilities, and its cost comparison with standard sensors.

Technical memo, project 0-6132 : task 6 - test sections in the districts.

DOT National Transportation Integrated Search

2011-02-01

This Tech Memo provides a summary of the Lab Test, Distress Survey, and Construction Reports for the CAM Test Sections constructed on FM 158 (E William J. Bryan Pkwy) in the Bryan District. TTI was requested by both the Contractor (Knife River Corpor...

Initial validation of a virtual-reality robotic simulator.

PubMed

Lendvay, Thomas S; Casale, Pasquale; Sweet, Robert; Peters, Craig

2008-09-01

Robotic surgery is an accepted adjunct to minimally invasive surgery, but training is restricted to console time. Virtual-reality (VR) simulation has been shown to be effective for laparoscopic training and so we seek to validate a novel VR robotic simulator. The American Urological Association (AUA) Office of Education approved this study. Subjects enrolled in a robotics training course at the 2007 AUA annual meeting underwent skills training in a da Vinci dry-lab module and a virtual-reality robotics module which included a three-dimensional (3D) VR robotic simulator. Demographic and acceptability data were obtained, and performance metrics from the simulator were compared between experienced and nonexperienced roboticists for a ring transfer task. Fifteen subjects-four with previous robotic surgery experience and 11 without-participated. Nine subjects were still in urology training and nearly half of the group had reported playing video games. Overall performance of the da Vinci system and the simulator were deemed acceptable by a Likert scale (0-6) rating of 5.23 versus 4.69, respectively. Experienced subjects outperformed nonexperienced subjects on the simulator on three metrics: total task time (96 s versus 159 s, P < 0.02), economy of motion (1,301 mm versus 2,095 mm, P < 0.04), and time the telemanipulators spent outside of the center of the platform's workspace (4 s versus 35 s, P < 0.02). This is the first demonstration of face and construct validity of a virtual-reality robotic simulator. Further studies assessing predictive validity are ultimately required to support incorporation of VR robotic simulation into training curricula.

Analysis of CO2 trapping capacities and long-term migration for geological formations in the Norwegian North Sea using MRST-co2lab

NASA Astrophysics Data System (ADS)

Møll Nilsen, Halvor; Lie, Knut-Andreas; Andersen, Odd

2015-06-01

MRST-co2lab is a collection of open-source computational tools for modeling large-scale and long-time migration of CO2 in conductive aquifers, combining ideas from basin modeling, computational geometry, hydrology, and reservoir simulation. Herein, we employ the methods of MRST-co2lab to study long-term CO2 storage on the scale of hundreds of megatonnes. We consider public data sets of two aquifers from the Norwegian North Sea and use geometrical methods for identifying structural traps, percolation-type methods for identifying potential spill paths, and vertical-equilibrium methods for efficient simulation of structural, residual, and solubility trapping in a thousand-year perspective. In particular, we investigate how data resolution affects estimates of storage capacity and discuss workflows for identifying good injection sites and optimizing injection strategies.

Reaction time effects in lab- versus Web-based research: Experimental evidence.

PubMed

Hilbig, Benjamin E

2016-12-01

Although Web-based research is now commonplace, it continues to spur skepticism from reviewers and editors, especially whenever reaction times are of primary interest. Such persistent preconceptions are based on arguments referring to increased variation, the limits of certain software and technologies, and a noteworthy lack of comparisons (between Web and lab) in fully randomized experiments. To provide a critical test, participants were randomly assigned to complete a lexical decision task either (a) in the lab using standard experimental software (E-Prime), (b) in the lab using a browser-based version (written in HTML and JavaScript), or (c) via the Web using the same browser-based version. The classical word frequency effect was typical in size and corresponded to a very large effect in all three conditions. There was no indication that the Web- or browser-based data collection was in any way inferior. In fact, if anything, a larger effect was obtained in the browser-based conditions than in the condition relying on standard experimental software. No differences between Web and lab (within the browser-based conditions) could be observed, thus disconfirming any substantial influence of increased technical or situational variation. In summary, the present experiment contradicts the still common preconception that reaction time effects of only a few hundred milliseconds cannot be detected in Web experiments.

A disposable picolitre bioreactor for cultivation and investigation of industrially relevant bacteria on the single cell level.

PubMed

Grünberger, Alexander; Paczia, Nicole; Probst, Christopher; Schendzielorz, Georg; Eggeling, Lothar; Noack, Stephan; Wiechert, Wolfgang; Kohlheyer, Dietrich

2012-05-08

In the continuously growing field of industrial biotechnology the scale-up from lab to industrial scale is still a major hurdle to develop competitive bioprocesses. During scale-up the productivity of single cells might be affected by bioreactor inhomogeneity and population heterogeneity. Currently, these complex interactions are difficult to investigate. In this report, design, fabrication and operation of a disposable picolitre cultivation system is described, in which environmental conditions can be well controlled on a short time scale and bacterial microcolony growth experiments can be observed by time-lapse microscopy. Three exemplary investigations will be discussed emphasizing the applicability and versatility of the device. Growth and analysis of industrially relevant bacteria with single cell resolution (in particular Escherichia coli and Corynebacterium glutamicum) starting from one single mother cell to densely packed cultures is demonstrated. Applying the picolitre bioreactor, 1.5-fold increased growth rates of C. glutamicum wild type cells were observed compared to typical 1 litre lab-scale batch cultivation. Moreover, the device was used to analyse and quantify the morphological changes of an industrially relevant l-lysine producer C. glutamicum after artificially inducing starvation conditions. Instead of a one week lab-scale experiment, only 1 h was sufficient to reveal the same information. Furthermore, time lapse microscopy during 24 h picolitre cultivation of an arginine producing strain containing a genetically encoded fluorescence sensor disclosed time dependent single cell productivity and growth, which was not possible with conventional methods.

Effects of activity repetition training with Salat (prayer) versus task oriented training on functional outcomes of stroke.

PubMed

Ghous, Misbah; Malik, Arshad Nawaz; Amjad, Mian Imran; Kanwal, Maria

2017-07-01

Stroke is one of most disabling condition which directly affects quality of life. The objective of this study was to compare the effect of activity repetition training with salat (prayer) versus task oriented training on functional outcomes of stroke. The study design was randomized control trial and 32 patients were randomly assigned into two groups'. The stroke including infarction or haemorrhagic, age bracket 30-70 years was included. The demographics were recorded and standardized assessment tool included Berg Balance Scale (BBS), Motor assessment scale (MAS) and Time Up and Go Test (TUG). The measurements were obtained at baseline, after four and six weeks. The mean age of the patients was 54.44±10.59 years with 16 (59%) male and 11(41%) female patients. Activity Repetition Training group showed significant improvement (p<0.05) and is effective in enhancing the functional status as compare to task oriented training group. The repetition with motivation and concentration is the key in re-learning process of neural plasticity.

Novel Process for Removal and Recovery of Vapor Phase Mercury

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greenwell, Collin; Roberts, Daryl L; Albiston, Jason

We demonstrated in the Phase I program all key attributes of a new technology for removing mercury from flue gases, namely, a) removal of greater than 95% of both elemental and oxidized forms of mercury, both in the laboratory and in the field b) regenerability of the sorbent c) ability to scale up, and d) favorable economics. The Phase I program consisted of four tasks other than project reporting: Task I-1 Screen Sorbent Configurations in the Laboratory Task I-2 Design and Fabricate Bench-Scale Equipment Task I-3 Test Bench-Scale Equipment on Pilot Combustor Task I-4 Evaluate Economics Based on Bench-Scale Resultsmore » In Task I-1, we demonstrated that the sorbents are thermally durable and are regenerable through at least 55 cycles of mercury uptake and desorption. We also demonstrated two low-pressure- drop configurations of the sorbent, namely, a particulate form and a monolithic form. We showed that the particulate form of the sorbent would take up 100% of the mercury so long as the residence time in a bed of the sorbent exceeded 0.1 seconds. In principle, the particulate form of the sorbent could be imbedded in the back side of a higher temperature bag filter in a full-scale application. With typical bag face velocities of four feet per minute, the thickness of the particulate layer would need to be about 2000 microns to accomplish the uptake of the mercury. For heat transfer efficiency, however, we believed the monolithic form of the sorbent would be the more practical in a full scale application. Therefore, we purchased commercially-available metallic monoliths and applied the sorbent to the inside of the flow channels of the monoliths. At face velocities we tested (up to 1.5 ft/sec), these monoliths had less than 0.05 inches of water pressure drop. We tested the monolithic form of the sorbent through 21 cycles of mercury sorption and desorption in the laboratory and included a test of simultaneous uptake of both mercury and mercuric chloride. Overall, in Task I-1, we found that the particulate and monolith forms of the sorbent were thermally stable and durable and would repeatedly sorb and desorb 100% of the mercury, including mercuric chloride, with low pressure drop and short residence times at realistic flue gas conditions.« less

Development of a magnetic lab-on-a-chip for point-of-care sepsis diagnosis

NASA Astrophysics Data System (ADS)

Schotter, Joerg; Shoshi, Astrit; Brueckl, Hubert

2009-05-01

We present design criteria, operation principles and experimental examples of magnetic marker manipulation for our magnetic lab-on-a-chip prototype. It incorporates both magnetic sample preparation and detection by embedded GMR-type magnetoresistive sensors and is optimized for the automated point-of-care detection of four different sepsis-indicative cytokines directly from about 5 μl of whole blood. The sample volume, magnetic particle size and cytokine concentration determine the microfluidic volume, sensor size and dimensioning of the magnetic gradient field generators. By optimizing these parameters to the specific diagnostic task, best performance is expected with respect to sensitivity, analysis time and reproducibility.

Networking Labs in the Online Environment: Indicators for Success

ERIC Educational Resources Information Center

Lahoud, Hilmi A.; Krichen, Jack P.

2010-01-01

Several techniques have been used to provide hands-on educational experiences to online learners, including remote labs, simulation software, and virtual labs, which offer a more structured environment, including simulations and scheduled asynchronous access to physical resources. This exploratory study investigated how these methods can be used…

BLINKER: Automated Extraction of Ocular Indices from EEG Enabling Large-Scale Analysis.

PubMed

Kleifges, Kelly; Bigdely-Shamlo, Nima; Kerick, Scott E; Robbins, Kay A

2017-01-01

Electroencephalography (EEG) offers a platform for studying the relationships between behavioral measures, such as blink rate and duration, with neural correlates of fatigue and attention, such as theta and alpha band power. Further, the existence of EEG studies covering a variety of subjects and tasks provides opportunities for the community to better characterize variability of these measures across tasks and subjects. We have implemented an automated pipeline (BLINKER) for extracting ocular indices such as blink rate, blink duration, and blink velocity-amplitude ratios from EEG channels, EOG channels, and/or independent components (ICs). To illustrate the use of our approach, we have applied the pipeline to a large corpus of EEG data (comprising more than 2000 datasets acquired at eight different laboratories) in order to characterize variability of certain ocular indicators across subjects. We also investigate dependence of ocular indices on task in a shooter study. We have implemented our algorithms in a freely available MATLAB toolbox called BLINKER. The toolbox, which is easy to use and can be applied to collections of data without user intervention, can automatically discover which channels or ICs capture blinks. The tools extract blinks, calculate common ocular indices, generate a report for each dataset, dump labeled images of the individual blinks, and provide summary statistics across collections. Users can run BLINKER as a script or as a plugin for EEGLAB. The toolbox is available at https://github.com/VisLab/EEG-Blinks. User documentation and examples appear at http://vislab.github.io/EEG-Blinks/.

How the Principles of Green Chemistry Changed the Way Organic Chemistry Labs Are Taught at the University of Detroit Mercy

NASA Astrophysics Data System (ADS)

Mio, Matthew J.

2017-02-01

Many logistic and instructional changes followed the incorporation of the 12 principles of green chemistry into organic chemistry laboratory courses at the University of Detroit Mercy. Over the last decade, institutional limitations have been turned into green chemical strengths in many areas, including integration of atom economy metrics into learning outcomes, replacing overly toxic equipment and reagents, and modifying matters of reaction scale and type.

Definition of experiments and instruments for a communication/navigation research laboratory. Volume 4: Programmatics

NASA Technical Reports Server (NTRS)

1972-01-01

Details are provided for scheduling, cost estimates, and support research and technology requirements for a space shuttle supported manned research laboratory to conduct selected communication and navigation experiments. A summary of the candidate program and its time phasing is included, as well as photographs of the 1/20 scale model of the shuttle supported Early Comm/Nav Research Lab showing the baseline, in-bay arrangement and the out-of-bay configuration.

Robotics and STEM Learning: Students' Achievements in Assignments According to the P3 Task Taxonomy--Practice, Problem Solving, and Projects

ERIC Educational Resources Information Center

Barak, Moshe; Assal, Muhammad

2018-01-01

This study presents the case of development and evaluation of a STEM-oriented 30-h robotics course for junior high school students (n = 32). Class activities were designed according to the P3 Task Taxonomy, which included: (1) practice-basic closed-ended tasks and exercises; (2) problem solving--small-scale open-ended assignments in which the…

GRC-2013-C-03877

NASA Image and Video Library

2009-09-26

The Advanced Stirling Convertor (ASC) is being developed by Sunpower, Inc. for NASA's Glenn Research Center (GRC) with critical technology support tasks led by GRC. The goal of the ASC project is to develop a highly efficient, low mass, reliable power convertor for future Radioisotope Power Systems (RPS), NASA's Science Mission Directorate; Stirling Lab

GRC-2013-C-03878

NASA Image and Video Library

2009-09-26

The Advanced Stirling Convertor (ASC) is being developed by Sunpower, Inc. for NASA's Glenn Research Center (GRC) with critical technology support tasks led by GRC. The goal of the ASC project is to develop a highly efficient, low mass, reliable power convertor for future Radioisotope Power Systems (RPS), NASA's Science Mission Directorate; Stirling Lab

GRC-2013-C-03843

NASA Image and Video Library

2009-09-26

The Advanced Stirling Convertor (ASC) is being developed by Sunpower, Inc. for NASA's Glenn Research Center (GRC) with critical technology support tasks led by GRC. The goal of the ASC project is to develop a highly efficient, low mass, reliable power convertor for future Radioisotope Power Systems (RPS), NASA's Science Mission Directorate; Stirling Lab

Enclothed Cognition and Controlled Attention during Insight Problem-Solving

ERIC Educational Resources Information Center

Van Stockum, Charles A., Jr.; DeCaro, Marci S.

2014-01-01

Individual differences in working memory capacity (WMC) increase the ability and tendency to devote greater attentional control to a task--improving performance on a wide range of skills. In addition, recent research on enclothed cognition demonstrates that the situational influence of wearing a white lab coat increases controlled attention, due…

Inexpensive Data Acquisition with a Sound Card

ERIC Educational Resources Information Center

Hassan, Umer; Pervaiz, Saad; Anwar, Muhammad Sabieh

2011-01-01

Signal generators, oscilloscopes, and data acquisition (DAQ) systems are standard components of the modern experimental physics laboratory. The sound card, a built-in component in the ubiquitous personal computer, can be utilized for all three of these tasks and offers an attractive option for labs in developing countries such as…

Comparative Cognitive Task Analyses of Experimental Science and Instructional Laboratory Courses

ERIC Educational Resources Information Center

Wieman, Carl

2015-01-01

Undergraduate instructional labs in physics generate intense opinions. Their advocates are passionate as to their importance for teaching physics as an experimental activity and providing "hands-on" learning experiences, while their detractors (often but not entirely students) offer harsh criticisms that they are pointless, confusing and…

Lab and Pore-Scale Study of Low Permeable Soils Diffusional Tortuosity

NASA Astrophysics Data System (ADS)

Lekhov, V.; Pozdniakov, S. P.; Denisova, L.

2016-12-01

Diffusion plays important role in contaminant spreading in low permeable units. The effective diffusion coefficient of saturated porous medium depends on this coefficient in water, porosity and structural parameter of porous space - tortuosity. Theoretical models of relationship between porosity and diffusional tortuosity are usually derived for conceptual granular models of medium filled by solid particles of simple geometry. These models usually do not represent soils with complex microstructure. The empirical models, like as Archie's law, based on the experimental electrical conductivity data are mostly useful for practical applications. Such models contain empirical parameters that should be defined experimentally for given soil type. In this work, we compared tortuosity values obtained in lab-scale diffusional experiments and pore scale diffusion simulation for the studied soil microstructure and exanimated relationship between tortuosity and porosity. Samples for the study were taken from borehole cores of low-permeable silt-clay formation. Using the samples of 50 cm3 we performed lab scale diffusional experiments and estimated the lab-scale tortuosity. Next using these samples we studied the microstructure with X-ray microtomograph. Shooting performed on undisturbed microsamples of size 1,53 mm with a resolution ×300 (10243 vox). After binarization of each obtained 3-D structure, its spatial correlation analysis was performed. This analysis showed that the spatial correlation scale of the indicator variogram is considerably smaller than microsample length. Then there was the numerical simulation of the Laplace equation with binary coefficients for each microsamples. The total number of simulations at the finite-difference grid of 1753 cells was 3500. As a result the effective diffusion coefficient, tortuosity and porosity values were obtained for all studied microsamples. The results were analyzed in the form of graph of tortuosity versus porosity. The 6 experimental tortuosity values well agree with pore-scale simulations falling in the general pattern that shows nonlinear decreasing of tortuosity with decreasing of porosity. Fitting this graph by Archie model we found exponent value in the range between 1,8 and 2,4. This work was supported by RFBR via grant 14-05-00409.

"Miniature Aces" NASA's Dale Reed Flight Research Laboratory

NASA Image and Video Library

2015-02-23

This video uncovers the workings, tools, and rationale of the scaled aircraft lab at NASA’s Armstrong Flight Research Center on Edwards Air Force Base. Watch commercial-off-the-shelf aircraft, one-of-a-kind designs, powered aircraft, and gliders take-off, fly, and land. The chief pilot and designer of the lab explains how and why they do what they do.

Surface Modified TiO2 Obscurants for Increased Safety and Performance

DTIC Science & Technology

2012-11-01

based obscurant devices in performance. 15. SUBJECT TERMS Obscurant, visible, IR , smoke, TiO2, aerosol, particle, surface modification...hexamethyldimethoxysilane IR Infrared wavelength LabRAM Lab scale Resonant Acoustic Mixer from Resodyn Corporation LPM Liters Per Minute M106 Currently fielded (Army...trinitrophloroglucinol UV-Vis Ultraviolet-visible wavelengths KEYWORDS Obscurant, visible, IR , smoke, TiO2, aerosol, particle, surface modification

Multi-Mission Simulation and Visualization for Real-Time Telemetry Display, Playback and EDL Event Reconstruction

NASA Technical Reports Server (NTRS)

Pomerantz, M. I.; Lim, C.; Myint, S.; Woodward, G.; Balaram, J.; Kuo, C.

2012-01-01

he Jet Propulsion Laboratory's Entry, Descent and Landing (EDL) Reconstruction Task has developed a software system that provides mission operations personnel and analysts with a real time telemetry-based live display, playback and post-EDL reconstruction capability that leverages the existing high-fidelity, physics-based simulation framework and modern game engine-derived 3D visualization system developed in the JPL Dynamics and Real Time Simulation (DARTS) Lab. Developed as a multi-mission solution, the EDL Telemetry Visualization (ETV) system has been used for a variety of projects including NASA's Mars Science Laboratory (MSL), NASA'S Low Density Supersonic Decelerator (LDSD) and JPL's MoonRise Lunar sample return proposal.

3D reconstruction optimization using imagery captured by unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Bassie, Abby L.; Meacham, Sean; Young, David; Turnage, Gray; Moorhead, Robert J.

2017-05-01

Because unmanned air vehicles (UAVs) are emerging as an indispensable image acquisition platform in precision agriculture, it is vitally important that researchers understand how to optimize UAV camera payloads for analysis of surveyed areas. In this study, imagery captured by a Nikon RGB camera attached to a Precision Hawk Lancaster was used to survey an agricultural field from six different altitudes ranging from 45.72 m (150 ft.) to 121.92 m (400 ft.). After collecting imagery, two different software packages (MeshLab and AgiSoft) were used to measure predetermined reference objects within six three-dimensional (3-D) point clouds (one per altitude scenario). In-silico measurements were then compared to actual reference object measurements, as recorded with a tape measure. Deviations of in-silico measurements from actual measurements were recorded as Δx, Δy, and Δz. The average measurement deviation in each coordinate direction was then calculated for each of the six flight scenarios. Results from MeshLab vs. AgiSoft offered insight into the effectiveness of GPS-defined point cloud scaling in comparison to user-defined point cloud scaling. In three of the six flight scenarios flown, MeshLab's 3D imaging software (user-defined scale) was able to measure object dimensions from 50.8 to 76.2 cm (20-30 inches) with greater than 93% accuracy. The largest average deviation in any flight scenario from actual measurements was 14.77 cm (5.82 in.). Analysis of the point clouds in AgiSoft (GPS-defined scale) yielded even smaller Δx, Δy, and Δz than the MeshLab measurements in over 75% of the flight scenarios. The precisions of these results are satisfactory in a wide variety of precision agriculture applications focused on differentiating and identifying objects using remote imagery.

Behavior of TiO₂ nanoparticles during incineration of solid paint waste: a lab-scale test.

PubMed

Massari, Andrea; Beggio, Marta; Hreglich, Sandro; Marin, Riccardo; Zuin, Stefano

2014-10-01

In order to assess the potential impacts posed by products containing engineered nanoparticles, it is essential to generate more data about the release of these particles from products' life cycle. Although first studies were performed to investigate the release of nanoparticles from use phase, very few data are available on the potential release from recycling or disposal of nano-enhanced products. In this work, we investigated the behavior of TiO2 nanoparticles from incineration of solid paint waste containing these particles. Solid paint debris with and without TiO2 nanoparticles were treated in a lab scale incineration plant at 950°C (combustion temperature) and in oxidizing atmosphere. The obtained ashes were also vitrified with additives and the release of Ti was finally evaluated by leaching test. From our incineration lab-scale experiment, we did not observe a release of TiO2 nanoparticles into the atmosphere, and Ti was attached to the surface of obtained solid residues (i.e. ashes). The characterization of ashes showed that TiO2 nanoparticles reacted during the incineration to give calcium titanate. Finally, a very low release of Ti was measured, less 1 mg/kg, during the leaching test of ashes vitrified with glass cullet and feldspathic inert. Our work suggests that TiO2 nanoparticles added in paints may undergo to physicochemical transformation during the incineration, and that Ti found in ashes may be strongly immobilized in glass matrix. Since this conclusion is based on lab-scale experiment, further research is required to identify which nanoparticles will be emitted to the environment from a real-word-incineration system of household hazardous waste. Copyright © 2014 Elsevier Ltd. All rights reserved.

The contribution of coping related variables and cardiac vagal activity on the performance of a dart throwing task under pressure.

PubMed

Mosley, Emma; Laborde, Sylvain; Kavanagh, Emma

2017-10-01

The aims of this study were 1) to assess the predictive role of coping related variables (CRV) on cardiac vagal activity (derived from heart rate variability), and 2) to investigate the influence of CRV (including cardiac vagal activity) on a dart throwing task under low pressure (LP) and high pressure (HP) conditions. Participants (n=51) completed trait CRV questionnaires: Decision Specific Reinvestment Scale, Movement Specific Reinvestment Scale and Trait Emotional Intelligence Questionnaire. They competed in a dart throwing task under LP and HP conditions. Cardiac vagal activity measurements were taken at resting, task and during recovery for 5min. Self-reported ratings of stress were recorded at three time points via a visual analogue scale. Upon completion of the task, self-report measures of motivation, stress appraisal, attention, perceived pressure and dart throwing experience were completed. Results indicated that resting cardiac vagal activity had no predictors. Task cardiac vagal activity was predicted by resting cardiac vagal activity in both pressure conditions with the addition of a trait CRV in HP. Post task cardiac vagal activity was predicted by resting cardiac vagal activity in both conditions with the addition of a trait CRV in HP. Cardiac vagal reactivity (difference from resting to task) was predicted by a trait CRV in HP conditions. Cardiac vagal recovery (difference from task to post task) was predicted by a state CRV only in LP. Dart throwing task performance was predicted by a combination of both CRV and cardiac vagal activity. The current research suggests that coping related variables and cardiac vagal activity influence dart throwing task performance differently dependent on pressure condition. Copyright © 2017 Elsevier Inc. All rights reserved.

Lab-on-a-Chip Based Protein Crystallization

NASA Technical Reports Server (NTRS)

vanderWoerd, Mark J.; Brasseur, Michael M.; Spearing, Scott F.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

We are developing a novel technique with which we will grow protein crystals in very small volumes, utilizing chip-based, microfluidic ("LabChip") technology. This development, which is a collaborative effort between NASA's Marshall Space Flight Center and Caliper Technologies Corporation, promises a breakthrough in the field of protein crystal growth. Our initial results obtained from two model proteins, Lysozyme and Thaumatin, show that it is feasible to dispense and adequately mix protein and precipitant solutions on a nano-liter scale. The mixtures have shown crystal growth in volumes in the range of 10 nanoliters to 5 microliters. In addition, large diffraction quality crystals were obtained by this method. X-ray data from these crystals were shown to be of excellent quality. Our future efforts will include the further development of protein crystal growth with LabChip(trademark) technology for more complex systems. We will initially address the batch growth method, followed by the vapor diffusion method and the liquid-liquid diffusion method. The culmination of these chip developments is to lead to an on orbit protein crystallization facility on the International Space Station. Structural biologists will be invited to utilize the on orbit Iterative Biological Crystallization facility to grow high quality macromolecular crystals in microgravity.

Infusion of Climate Change and Geospatial Science Concepts into Environmental and Biological Science Curriculum

NASA Astrophysics Data System (ADS)

Balaji Bhaskar, M. S.; Rosenzweig, J.; Shishodia, S.

2017-12-01

The objective of our activity is to improve the students understanding and interpretation of geospatial science and climate change concepts and its applications in the field of Environmental and Biological Sciences in the College of Science Engineering and Technology (COEST) at Texas Southern University (TSU) in Houston, TX. The courses of GIS for Environment, Ecology and Microbiology were selected for the curriculum infusion. A total of ten GIS hands-on lab modules, along with two NCAR (National Center for Atmospheric Research) lab modules on climate change were implemented in the "GIS for Environment" course. GIS and Google Earth Labs along with climate change lectures were infused into Microbiology and Ecology courses. Critical thinking and empirical skills of the students were assessed in all the courses. The student learning outcomes of these courses includes the ability of students to interpret the geospatial maps and the student demonstration of knowledge of the basic principles and concepts of GIS (Geographic Information Systems) and climate change. At the end of the courses, students developed a comprehensive understanding of the geospatial data, its applications in understanding climate change and its interpretation at the local and regional scales during multiple years.

Microcontact Printing of Thiol-Functionalized Ionic Liquid Microarrays for "Membrane-less" and "Spill-less" Gas Sensors.

PubMed

Gondosiswanto, Richard; Gunawan, Christian A; Hibbert, David B; Harper, Jason B; Zhao, Chuan

2016-11-16

Lab-on-a-chip systems have gained significant interest for both chemical synthesis and assays at the micro-to-nanoscale with a unique set of benefits. However, solvent volatility represents one of the major hurdles to the reliability and reproducibility of the lab-on-a-chip devices for large-scale applications. Here we demonstrate a strategy of combining nonvolatile and functionalized ionic liquids with microcontact printing for fabrication of "wall-less" microreactors and microfluidics with high reproducibility and high throughput. A range of thiol-functionalized ionic liquids have been synthesized and used as inks for microcontact printing of ionic liquid microdroplet arrays onto gold chips. The covalent bonds formed between the thiol-functionalized ionic liquids and the gold substrate offer enhanced stability of the ionic liquid microdroplets, compared to conventional nonfunctionalized ionic liquids, and these microdroplets remain stable in a range of nonpolar and polar solvents, including water. We further demonstrate the use of these open ionic liquid microarrays for fabrication of "membrane-less" and "spill-less" gas sensors with enhanced reproducibility and robustness. Ionic-liquid-based microarray and microfluidics fabricated using the described microcontact printing may provide a versatile platform for a diverse number of applications at scale.

Expanding a dynamic flux balance model of yeast fermentation to genome-scale

PubMed Central

2011-01-01

Background Yeast is considered to be a workhorse of the biotechnology industry for the production of many value-added chemicals, alcoholic beverages and biofuels. Optimization of the fermentation is a challenging task that greatly benefits from dynamic models able to accurately describe and predict the fermentation profile and resulting products under different genetic and environmental conditions. In this article, we developed and validated a genome-scale dynamic flux balance model, using experimentally determined kinetic constraints. Results Appropriate equations for maintenance, biomass composition, anaerobic metabolism and nutrient uptake are key to improve model performance, especially for predicting glycerol and ethanol synthesis. Prediction profiles of synthesis and consumption of the main metabolites involved in alcoholic fermentation closely agreed with experimental data obtained from numerous lab and industrial fermentations under different environmental conditions. Finally, fermentation simulations of genetically engineered yeasts closely reproduced previously reported experimental results regarding final concentrations of the main fermentation products such as ethanol and glycerol. Conclusion A useful tool to describe, understand and predict metabolite production in batch yeast cultures was developed. The resulting model, if used wisely, could help to search for new metabolic engineering strategies to manage ethanol content in batch fermentations. PMID:21595919

Comparison of two simulation systems to support robotic-assisted surgical training: a pilot study (Swine model).

PubMed

Whitehurst, Sabrina V; Lockrow, Ernest G; Lendvay, Thomas S; Propst, Anthony M; Dunlow, Susan G; Rosemeyer, Christopher J; Gobern, Joseph M; White, Lee W; Skinner, Anna; Buller, Jerome L

2015-01-01

To compare the efficacy of simulation-based training between the Mimic dV- Trainer and traditional dry lab da Vinci robot training. A prospective randomized study analyzing the performance of 20 robotics-naive participants. Participants were enrolled in an online da Vinci Intuitive Surgical didactic training module, followed by training in use of the da Vinci standard surgical robot. Spatial ability tests were performed as well. Participants were randomly assigned to 1 of 2 training conditions: performance of 3 Fundamentals of Laparoscopic Surgery dry lab tasks using the da Vinci or performance of 4 dV-Trainer tasks. Participants in both groups performed all tasks to empirically establish proficiency criterion. Participants then performed the transfer task, a cystotomy closure using the daVinci robot on a live animal (swine) model. The performance of robotic tasks was blindly assessed by a panel of experienced surgeons using objective tracking data and using the validated Global Evaluative Assessment of Robotic Surgery (GEARS), a structured assessment tool. No statistically significant difference in surgeon performance was found between the 2 training conditions, dV-Trainer and da Vinci robot. Analysis of a 95% confidence interval for the difference in means (-0.803 to 0.543) indicated that the 2 methods are unlikely to differ to an extent that would be clinically meaningful. Based on the results of this study, a curriculum on the dV- Trainer was shown to be comparable to traditional da Vinci robot training. Therefore, we have identified that training on a virtual reality system may be an alternative to live animal training for future robotic surgeons. Published by Elsevier Inc.

SPAGHETTILENS: A software stack for modeling gravitational lenses by citizen scientists

NASA Astrophysics Data System (ADS)

Küng, R.

2018-04-01

The 2020s are expected to see tens of thousands of lens discoveries. Mass reconstruction or modeling of these lenses will be needed, but current modeling methods are time intensive for specialists and expert human resources do not scale. SpaghettiLens approaches this challenge with the help of experienced citizen scientist volunteers who have already been involved in finding lenses. A top level description is as follows. Citizen scientists look at data and provide a graphical input based on Fermat's principle which we call a Spaghetti Diagram. This input works as a model configuration. It is followed by the generation of the model, which is a compute intensive task done server side though a task distribution system. Model results are returned in graphical form to the citizen scientist, who examines and then either forwards them for forum discussion or rejects the model and retries. As well as configuring models, citizen scientists can also modify existing model configurations, which results in a version tree of models and makes the modeling process collaborative. SpaghettiLens is designed to be scalable and could be adopted to problems with similar characteristics. It is licensed under the MIT license, released at http://labs.spacewarps.org and the source code is available at https://github.com/RafiKueng/SpaghettiLens.

Psychomotor Vigilance Task Evaluation for Touchscreen Devices

NASA Technical Reports Server (NTRS)

Arsintescu, Lucia

2017-01-01

The Psychomotor Vigilance Task (PVT) is considered the gold standard fatigue detection device and is used frequently in fatigue research. The purpose of this study was to compare a psychomotor vigilance task developed for use on touchscreen devices with the original PVT-192 in conditions of acute sleep loss and circadian desynchronization. Participants arrived in the lab approximately two hours after their habitual time and were asked to stay awake for up to 24 hrs and take 5-minute reaction time tests every 2 hours on two different devices: the original PVT-192 and NASA-PVT on an iPod. We found that the NASA-PVT and PVT-192 were sensitive to the 24 hrs of extended wakefulness.

Ultracapacitors for automotive applications

NASA Astrophysics Data System (ADS)

Ashtiani, Cyrus; Wright, Randy; Hunt, Gary

In response to a growing consensus in the auto industry that ultracapacitors can potentially play a key role in the modern vehicle power distribution network, a task force was created at the United States Advanced Battery Consortium (USABC) to tackle issues facing the fledging industry. The task force embarked on first developing and establishing standards for performance and abuse tolerance of ultracapacitors in collaboration with the U.S. Department of Energy and National Labs. Subsequently, potential applications in the automotive industry were identified and a consensus requirement specification was drawn as a development guide for the industry.

Incorporating inquiry and the process of science into introductory astronomy labs at the George Washington University

NASA Astrophysics Data System (ADS)

Cobb, Bethany E.

2018-01-01

Since 2013, the Physics Department at GWU has used student-centered active learning in the introductory astronomy course “Introduction to the Cosmos.” Class time is spent in groups on questions, math problems, and hands-on activities, with multiple instructors circulating to answer questions and engage with the students. The students have responded positively to this active-learning. Unfortunately, in transitioning to active-learning there was no time to rewrite the labs. Very quickly, the contrast between the dynamic classroom and the traditional labs became apparent. The labs were almost uniformly “cookie-cutter” in that the procedure and analysis were specified step-by-step and there was just one right answer. Students rightly criticized the labs for lacking a clear purpose and including busy-work. Furthermore, this class fulfills the GWU scientific reasoning general education requirement and thus includes learning objectives related to understanding the scientific method, testing hypotheses with data, and considering uncertainty – but the traditional labs did not require these skills. I set out to rejuvenate the lab sequence by writing new inquiry labs based on both topic-specific and scientific reasoning learning objectives. While inquiry labs can be challenging for the students, as they require active thinking and creativity, these labs engage the students more thoroughly in the scientific process. In these new labs, whenever possible, I include real astronomical data and ask the students to use digital tools (SDSS SkyServer, SOHO archive) as if they are real astronomers. To allow students to easily plot, manipulate and analyze data, I built “smart” Excel files using formulas, dropdown menus and macros. The labs are now much more authentic and thought-provoking. Whenever possible, students independently develop questions, hypotheses, and procedures and the scientific method is “scaffolded” over the semester by providing more guidance in the early labs and more independence later on. Finally, in every lab, students must identify and reflect on sources of error. These labs are more challenging for the instructors to run and to grade, but they are much more satisfying when it comes to student learning.

Zero-valent iron/biotic treatment system for perchlorate-contaminated water: lab-scale performance, modeling, and full-scale implications

EPA Science Inventory

The computer program AQUASIM was used to model biological treatment of perchlorate-contaminated water using zero-valent iron corrosion as the hydrogen gas source. The laboratory-scale column was seeded with an autohydrogenotrophic microbial consortium previously shown to degrade ...

Computers, Networks, and Desegregation at San Jose High Academy.

ERIC Educational Resources Information Center

Solomon, Gwen

1987-01-01

Describes magnet high school which was created in California to meet desegregation requirements and emphasizes computer technology. Highlights include local computer networks that connect science and music labs, the library/media center, business computer lab, writing lab, language arts skills lab, and social studies classrooms; software; teacher…

Scaling behavior in exclusive meson photoproduction from Jefferson Lab at large momentum transfers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dey, Biplab

2014-07-01

With the availability of new high-statistics and wide-angle measurements for several exclusive non-πN meson photoproduction channels from Jefferson Lab, we examine the fundamental scaling law of 90° scattering in QCD that was originally derived in the high-energy perturbative limit. The data show scaling to be prominently visible even in the medium-energy domain of 2.5 GeV ≲√s≲2.84 GeV, where √s is the center-of-mass energy. While constituent quark exchange suffices for pseudoscalar mesons, additional gluon exchanges from higher Fock states of the hadronic wave functions appear be needed for vector-meson production. Finally, the case of the Φ(1020), where two-gluon exchanges are knownmore » to dominate, is especially illuminating.« less

Development and psychometric validation of the Task-Specific Self-Efficacy Scale for Chinese people with mental illness.

PubMed

Chou, Chih Chin; Cardoso, Elizabeth Da Silva; Chan, Fong; Tsang, Hector W H; Wu, Mingyi

2007-12-01

The aim of this study was to validate a Task-Specific Self-Efficacy Scale for Chinese people with mental illness. The study included 79 men and 77 women with chronic mental illness. The Task-Specific Self-Efficacy Scale for People with Mental Illness (TSSES-PMI) and Change Assessment Questionnaire for People with Severe and Persistent Mental Illness were used as measures for the study. Factor analysis of the TSSES-PMI resulted in four subscales: Symptom Management Skills, Work-Related Skills, Help-Seeking Skills, and Self-Emotional-Regulation Skills. These community living skills were found to be related to the level of readiness for psychiatric rehabilitation among Chinese people with mental illness. In conclusion the results support the construct validity of the TSSES-PMI for the Chinese population and the TSSES-PMI can be a useful instrument for working with Chinese people with mental illnesses.

Characterization of Lactobacillus brevis L62 strain, highly tolerant to copper ions.

PubMed

Mrvčić, Jasna; Butorac, Ana; Solić, Ema; Stanzer, Damir; Bačun-Družina, Višnja; Cindrić, Mario; Stehlik-Tomas, Vesna

2013-01-01

Lactic acid bacteria (LAB) as starter culture in food industry must be suitable for large-scale industrial production and possess the ability to survive in unfavorable processes and storage conditions. Approaches taken to address these problems include the selection of stress-resistant strains. In food industry, LAB are often exposed to metal ions induced stress. The interactions between LAB and metal ions are very poorly investigated. Because of that, the influence of non-toxic, toxic and antioxidant metal ions (Zn, Cu, and Mn) on growth, acid production, metal ions binding capacity of wild and adapted species of Leuconostoc mesenteroides L3, Lactobacillus brevis L62 and Lactobacillus plantarum L73 were investigated. The proteomic approach was applied to clarify how the LAB cells, especially the adapted ones, protect themselves and tolerate high concentrations of toxic metal ions. Results have shown that Zn and Mn addition into MRS medium in the investigated concentrations did not have effect on the bacterial growth and acid production, while copper ions were highly toxic, especially in static conditions. Leuc. mesenteroides L3 was the most efficient in Zn binding processes among the chosen LAB species, while L. plantarum L73 accumulated the highest concentration of Mn. L. brevis L62 was the most copper resistant species. Adaptation had a positive effect on growth and acid production of all species in the presence of copper. However, the adapted species incorporated less metal ions than the wild species. The exception was adapted L. brevis L62 that accumulated high concentration of copper ions in static conditions. The obtained results showed that L. brevis L62 is highly tolerant to copper ions, which allows its use as starter culture in fermentative processes in media with high concentration of copper ions.

SILVERRUSH. II. First catalogs and properties of ˜2000 Lyα emitters and blobs at z ˜ 6-7 identified over the 14-21 deg2 sky*

NASA Astrophysics Data System (ADS)

Shibuya, Takatoshi; Ouchi, Masami; Konno, Akira; Higuchi, Ryo; Harikane, Yuichi; Ono, Yoshiaki; Shimasaku, Kazuhiro; Taniguchi, Yoshiaki; Kobayashi, Masakazu A. R.; Kajisawa, Masaru; Nagao, Tohru; Furusawa, Hisanori; Goto, Tomotsugu; Kashikawa, Nobunari; Komiyama, Yutaka; Kusakabe, Haruka; Lee, Chien-Hsiu; Momose, Rieko; Nakajima, Kimihiko; Tanaka, Masayuki; Wang, Shiang-Yu; Yuma, Suraphong

2018-01-01

We present an unprecedentedly large catalog consisting of 2230 ≳ L* Lyα emitters (LAEs) at z = 5.7 and 6.6 on the 13.8 and 21.2 deg2 sky, respectively, that are identified by the SILVERRUSH program with the first narrow-band imaging data of the Hyper Suprime-Cam (HSC) survey. We confirm that the LAE catalog is reliable on the basis of 96 LAEs whose spectroscopic redshifts are already determined by this program and previous studies. This catalogue is also available online. Based on this catalogue, we derive the rest-frame Lyα equivalent-width distributions of LAEs at z ≃ 5.7-6.6 that are reasonably explained by the exponential profiles with scale lengths of ≃ 120-170 Å, showing no significant evolution from z ≃ 5.7 to z ≃ 6.6. We find that 275 LAEs with large equivalent widths (LEWs) of >240 Å are candidates of young metal poor galaxies and AGNs. We also find that the fraction of LEW LAEs to all LAEs is 4% and 21% at z ≃ 5.7 and z ≃ 6.6, respectively. Our LAE catalog includes 11 Lyα blobs (LABs) that are LAEs with spatially extended Lyα emission with a profile that is clearly distinguished from those of stellar objects at the ≳3σ level. The number density of the LABs at z = 6-7 is ˜10-7-10-6 Mpc-3, being ˜10-100 times lower than those claimed for LABs at z ≃ 2-3, suggestive of disappearing LABs at z ≳ 6, albeit with the different selection methods and criteria for the low and high-z LABs.

The formation of potentially harmful compounds in churros, a Spanish fried-dough pastry, as influenced by deep frying conditions.

PubMed

Morales, F J; Arribas-Lorenzo, G

2008-07-15

Colour, moisture, hydroxymethylfurfural (HMF) and acrylamide (AA) were investigated in traditional Spanish churros. Samples were deep-fried in sunflower oil at lab-scale temperatures of 180, 190 and 200°C and for frying times of 2, 3, 5 and 7min. Fresh made churros were also obtained from local producers. HMF ranged from 1.2±0.02 to 221.4±2.02mg/kg for lab-scale experiments and an average of 74.3±47.5mg/kg was recorded in commercial samples. AA ranged from below the limit of quantitation to 90±0.6μg/kg for lab-scale experiments and an average of 46±24.5μg/kg was measured in commercial samples. Temperatures between 185 and 200°C are commonly used to obtain churros with an acceptable palatability and a crispy surface. However, HMF and AA levels increased nearly two-fold from 190 to 200°C at the same frying times, indicating that a more precise control of frying temperatures is required to minimize their formation. Copyright © 2007 Elsevier Ltd. All rights reserved.

Numerical Modeling Studies of Wake Vortex Transport and Evolution Within the Planetary Boundary Layer

NASA Technical Reports Server (NTRS)

Lin, Yuh-Lang; Arya, S. Pal; Kaplan, Michael L.; Shen, Shaohua

1998-01-01

In support of the wake vortex effect of the Terminal Area Productivity program, we have put forward four tasks to be accomplished in our proposal. The first task is validation of two-dimensional wake vortex-turbulence interaction. The second task is investigation of three-dimensional interaction between wake vortices and atmospheric boundary layer (ABL) turbulence. The third task is ABL studies. The, fourth task is addition of a Klemp-Durran condition at the top boundary for TASS model. The accomplishment of these tasks will increase our understanding of the dynamics of wake vortex and improve forecasting systems responsible for air safety and efficiency. The first two tasks include following three parts: (a) Determine significant length scale for vortex decay and transport, especially the length scales associated with the onset of Crow instability (Crow, 1970); (b) Study the effects of atmospheric turbulence on the decay of the wake vortices; and (c) Determine the relationships between decay rate, transport properties and atmospheric parameters based on large eddy simulation (LES) results and the observational data. These parameters may include turbulence kinetic energy, dissipation rate, wind shear and atmospheric stratification. The ABL studies cover LES modeling of turbulence structure within planetary boundary layer under transition and stable stratification conditions. Evidences have shown that the turbulence in the stable boundary layer can be highly intermittent and the length scales of eddies are very small compared to those in convective case. We proposed to develop a nesting grid mesh scheme and a modified Klemp-Durran conditions (Klemp and Wilhelmson, 1978) at the top boundary for TASS model to simulate planetary boundary layer under stable stratification conditions. During the past year, our group has made great efforts to carry out the above mentioned four tasks simultaneously. The work accomplished in the last year will be described in the next section.

Heat transfer analysis of a lab scale solar receiver using the discrete ordinates model

NASA Astrophysics Data System (ADS)

Dordevich, Milorad C. W.

This thesis documents the development, implementation and simulation outcomes of the Discrete Ordinates Radiation Model in ANSYS FLUENT simulating the radiative heat transfer occurring in the San Diego State University lab-scale Small Particle Heat Exchange Receiver. In tandem, it also serves to document how well the Discrete Ordinates Radiation Model results compared with those from the in-house developed Monte Carlo Ray Trace Method in a number of simplified geometries. The secondary goal of this study was the inclusion of new physics, specifically buoyancy. Implementation of an additional Monte Carlo Ray Trace Method software package known as VEGAS, which was specifically developed to model lab scale solar simulators and provide directional, flux and beam spread information for the aperture boundary condition, was also a goal of this study. Upon establishment of the model, test cases were run to understand the predictive capabilities of the model. It was shown that agreement within 15% was obtained against laboratory measurements made in the San Diego State University Combustion and Solar Energy Laboratory with the metrics of comparison being the thermal efficiency and outlet, wall and aperture quartz temperatures. Parametric testing additionally showed that the thermal efficiency of the system was very dependent on the mass flow rate and particle loading. It was also shown that the orientation of the small particle heat exchange receiver was important in attaining optimal efficiency due to the fact that buoyancy induced effects could not be neglected. The analyses presented in this work were all performed on the lab-scale small particle heat exchange receiver. The lab-scale small particle heat exchange receiver is 0.38 m in diameter by 0.51 m tall and operated with an input irradiation flux of 3 kWth and a nominal mass flow rate of 2 g/s with a suspended particle mass loading of 2 g/m3. Finally, based on acumen gained during the implementation and development of the model, a new and improved design was simulated to predict how the efficiency within the small particle heat exchange receiver could be improved through a few simple internal geometry design modifications. It was shown that the theoretical calculated efficiency of the small particle heat exchange receiver could be improved from 64% to 87% with adjustments to the internal geometry, mass flow rate, and mass loading.

Current status and challenges for automotive battery production technologies

NASA Astrophysics Data System (ADS)

Kwade, Arno; Haselrieder, Wolfgang; Leithoff, Ruben; Modlinger, Armin; Dietrich, Franz; Droeder, Klaus

2018-04-01

Production technology for automotive lithium-ion battery (LIB) cells and packs has improved considerably in the past five years. However, the transfer of developments in materials, cell design and processes from lab scale to production scale remains a challenge due to the large number of consecutive process steps and the significant impact of material properties, electrode compositions and cell designs on processes. This requires an in-depth understanding of the individual production processes and their interactions, and pilot-scale investigations into process parameter selection and prototype cell production. Furthermore, emerging process concepts must be developed at lab and pilot scale that reduce production costs and improve cell performance. Here, we present an introductory summary of the state-of-the-art production technologies for automotive LIBs. We then discuss the key relationships between process, quality and performance, as well as explore the impact of materials and processes on scale and cost. Finally, future developments and innovations that aim to overcome the main challenges are presented.

Expanding Participation in Fluid Dynamics Research

NASA Astrophysics Data System (ADS)

Tagg, Randall

2015-11-01

Two legacies provided by great scientists are scientific discoveries and more scientists. Is there a way that these impacts can be magnified? Examples using the Taylor-Couette experiment and other fluid dynamics problems will demonstrate that indeed more people can fruitfully engage in open and even bold investigation. Participants include high school students, teachers, undergraduates, artists, business developers and interested laypersons. With imagination, good training, and a suitable lab space, a special tribute can be given to those who mentor us by scaling up the breadth of their influence.

Gradient composite metal-ceramic foam as supportive component for planar SOFCs and MIEC membranes

NASA Astrophysics Data System (ADS)

Smorygo, Oleg; Mikutski, Vitali; Marukovich, Alexander; Sadykov, Vladislav; Usoltsev, Vladimir; Mezentseva, Natalia; Borodinecs, Anatolijs; Bobrenok, Oleg

2011-06-01

A novel approach to the design of planar gradient porous supports for the thin-film SOFCs and MIEC membranes is described. The support's thermal expansion is controlled by the creation of a two-component composite metal-ceramic foam structure. Thin MIEC membranes and SOFCs were prepared on the composite supports by the layerwise deposition of composite functional layers including complex fluorites and perovskites. Lab-scale studies demonstrated promising performance of both MIEC membrane and SOFC.

Indicators and Metrics for Evaluating the Sustainability of Chemical Processes

EPA Science Inventory

A metric-based method, called GREENSCOPE, has been developed for evaluating process sustainability. Using lab-scale information and engineering assumptions the method evaluates full-scale epresentations of processes in environmental, efficiency, energy and economic areas. The m...

Technologies for autonomous integrated lab-on-chip systems for space missions

NASA Astrophysics Data System (ADS)

Nascetti, A.; Caputo, D.; Scipinotti, R.; de Cesare, G.

2016-11-01

Lab-on-chip devices are ideal candidates for use in space missions where experiment automation, system compactness, limited weight and low sample and reagent consumption are required. Currently, however, most microfluidic systems require external desktop instrumentation to operate and interrogate the chip, thus strongly limiting their use as stand-alone systems. In order to overcome the above-mentioned limitations our research group is currently working on the design and fabrication of "true" lab-on-chip systems that integrate in a single device all the analytical steps from the sample preparation to the detection without the need for bulky external components such as pumps, syringes, radiation sources or optical detection systems. Three critical points can be identified to achieve 'true' lab-on-chip devices: sample handling, analytical detection and signal transduction. For each critical point, feasible solutions are presented and evaluated. Proposed microfluidic actuation and control is based on electrowetting on dielectrics, autonomous capillary networks and active valves. Analytical detection based on highly specific chemiluminescent reactions is used to avoid external radiation sources. Finally, the integration on the same chip of thin film sensors based on hydrogenated amorphous silicon is discussed showing practical results achieved in different sensing tasks.

The Multi-Level Classroom or the One Room Little Red School-House Revisited.

ERIC Educational Resources Information Center

Courchene, Robert

1984-01-01

Describes language lab listening activity designed to serve needs of the English as a second language class comprised of students at different levels of language proficiency, divergent native languages, multicultural backgrounds, and varying levels of formal education. Multilevel tasks are drawn from a common text, allowing students to do…

Connecting Earth Systems: Developing Holistic Understanding through the Earth-System-Science Model

ERIC Educational Resources Information Center

Gagnon, Valoree; Bradway, Heather

2012-01-01

For many years, Earth science concepts have been taught as thematic units with lessons in nice, neat chapter packages complete with labs and notes. But compartmentalized Earth science no longer exists, and implementing teaching methods that support student development of holistic understandings can be a time-consuming and difficult task. While…

Investigating a Chemoselective Grignard Reaction in an Undergraduate Discovery Lab to Predict Reactivity and Final Products

ERIC Educational Resources Information Center

Maher, Michael J.; Hayes, Colin O.; Vaccaro, Francesca A.; Flynn, Cailyn B.; Thedford, R. Paxton; Stephenson, Clifton J.

2016-01-01

A discovery-based Grignard experiment that emphasizes several important concepts in organic chemistry is reported. The Grignard reagent from 1- bromo-4-chlorobenzene was prepared and reacted with dimethylformamide (DMF) to synthesize 4-chlorobenzaldehyde. Students were tasked with predicting halogen reactivity in the formation of the Grignard…

TUW @ TREC Clinical Decision Support Track 2015

DTIC Science & Technology

2015-11-20

Symposium, IIiX ’14, pages 283–286. ACM, 2014. 11. J. Palotti, G. Zuccon, L. Goeuriot, L. Kelly, A. Hanbury, G. Jones, M. Lupu , and P. Pecina. Clef ehealth...L. Goeuriot, L. Kelly, A. Hanburyn, G. J. Jones, M. Lupu , and P. Pecina. CLEF eHealth evaluation lab 2015, task 2: Retrieving information about

Modeling the Bullying Prevention Program Preferences of Educators: A Discrete Choice Conjoint Experiment

ERIC Educational Resources Information Center

Cunningham, Charles E.; Vaillancourt, Tracy; Rimas, Heather; Deal, Ken; Cunningham, Lesley; Short, Kathy; Chen, Yvonne

2009-01-01

We used discrete choice conjoint analysis to model the bullying prevention program preferences of educators. Using themes from computerized decision support lab focus groups (n = 45 educators), we composed 20 three-level bullying prevention program design attributes. Each of 1,176 educators completed 25 choice tasks presenting experimentally…

Chemistry Lab--Heat Capacity.

ERIC Educational Resources Information Center

Stern, Robert

1998-01-01

Explores measuring the specific heat of a metal ball. The ball is heated to a known temperature then placed in cold water. Students measure the temperature gain of the water in this investigation of the principle of Conservation of Energy. As a second task, students make a precise determination of the density of the ball. (PVD)

The Impact of Hands-On Simulation Laboratories on Teaching of Wireless Communications

ERIC Educational Resources Information Center

Chou, Te-Shun; Vanderbye, Aaron

2017-01-01

Aim/Purpose: To prepare students with both theoretical knowledge and practical skills in the field of wireless communications. Background: Teaching wireless communications and networking is not an easy task because it involves broad subjects and abstract content. Methodology: A pedagogical method that combined lectures, labs, assignments, exams,…

NASA/WVU Software Research Laboratory, 1995

NASA Technical Reports Server (NTRS)

Sabolish, George J.; Callahan, John R.

1995-01-01

In our second year, the NASA/WVU Software Research Lab has made significant strides toward analysis and solution of major software problems related to V&V activities. We have established working relationships with many ongoing efforts within NASA and continue to provide valuable input into policy and decision-making processes. Through our publications, technical reports, lecture series, newsletters, and resources on the World-Wide-Web, we provide information to many NASA and external parties daily. This report is a summary and overview of some of our activities for the past year. This report is divided into 6 chapters: Introduction, People, Support Activities, Process, Metrics, and Testing. The Introduction chapter (this chapter) gives an overview of our project beginnings and targets. The People chapter focuses on new people who have joined the Lab this year. The Support chapter briefly lists activities like our WWW pages, Technical Report Series, Technical Lecture Series, and Research Quarterly newsletter. Finally, the remaining four chapters discuss the major research areas that we have made significant progress towards producing meaningful task reports. These chapters can be regarded as portions of drafts of our task reports.

Field Testing of a Wet FGD Additive for Enhanced Mercury Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gary Blythe; MariJon Owens

2007-12-31

This document is the final report for DOE-NETL Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project has been to demonstrate the use of two flue gas desulfurization (FGD) additives, Evonik Degussa Corporation's TMT-15 and Nalco Company's Nalco 8034, to prevent the re-emission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project was intended to demonstrate whether such additives can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine salt that can be separated from themore » FGD liquor and bulk solid byproducts for separate disposal. The project involved pilot- and full-scale tests of the additives in wet FGD absorbers. The tests were intended to determine required additive dosages to prevent Hg{sup 0} re-emissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Powder River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, Luminant Power (was TXU Generation Company LP), Southern Company, IPL (an AES company), Evonik Degussa Corporation and the Nalco Company. Luminant Power provided the Texas lignite/PRB co-fired test site for pilot FGD tests and project cost sharing. Southern Company provided the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, the pilot- and full-scale jet bubbling reactor (JBR) FGD systems tested, and project cost sharing. IPL provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Evonik Degussa Corporation provided the TMT-15 additive, and the Nalco Company provided the Nalco 8034 additive. Both companies also supplied technical support to the test program as in-kind cost sharing. The project was conducted in six tasks. Of the six tasks, Task 1 involved project planning and Task 6 involved management and reporting. The other four tasks involved field testing on FGD systems, either at pilot or full scale. These four tasks included: Task 2 - Pilot Additive Testing in Texas Lignite Flue Gas; Task 3 - Full-scale FGD Additive Testing in High-sulfur Eastern Bituminous Flue Gas; Task 4 - Pilot Wet Scrubber Additive Tests at Plant Yates; and Task 5 - Full-scale Additive Tests at Plant Yates. The pilot-scale tests were completed in 2005 and the full-scale test using high-sulfur coal was completed in 2006; only the TMT-15 additive was tested in these efforts. The Task 5 full-scale additive tests conducted at Southern Company's Plant Yates Unit 1 were completed in 2007, and both the TMT-15 and Nalco 8034 additives were tested.« less

Nanomanufacturing-related programs at NSF

NASA Astrophysics Data System (ADS)

Cooper, Khershed P.

2015-08-01

The National Science Foundation is meeting the challenge of transitioning lab-scale nanoscience and technology to commercial-scale through several nanomanufacturing-related research programs. The goal of the core Nanomanufacturing (NM) and the inter-disciplinary Scalable Nanomanufacturing (SNM) programs is to meet the barriers to manufacturability at the nano-scale by developing the fundamental principles for the manufacture of nanomaterials, nanostructures, nanodevices, and engineered nanosystems. These programs address issues such as scalability, reliability, quality, performance, yield, metrics, and cost, among others. The NM and SNM programs seek nano-scale manufacturing ideas that are transformative, that will be widely applicable and that will have far-reaching technological and societal impacts. It is envisioned that the results from these basic research programs will provide the knowledge base for larger programs such as the manufacturing Nanotechnology Science and Engineering Centers (NSECs) and the Nanosystems Engineering Research Centers (NERCs). Besides brief descriptions of these different programs, this paper will include discussions on novel

Emotion dysregulation and negative affect: Laboratory and EMA investigations in smokers.

PubMed

MacIntyre, Jessica M; Ruscio, Aimee C; Brede, Emily; Waters, Andrew J

2018-06-01

Difficulties in emotion regulation are associated with addictive behaviors, including smoking. Difficulties in emotion regulation may underlie large, rapid changes in negative affect that can increase likelihood of relapse. We investigated the association between emotion regulation ability and negative affect in smokers assessed both in the laboratory and in the field using Ecological Momentary Assessment. Adult community smokers ( N  = 44) carried a personal digital assistant (PDA) for two weeks and were instructed to complete assessments of negative affect multiple times per day. Participants were instructed that they could smoke as much or as little as they liked. The Difficulties in Emotion Regulation Scale (DERS) and the Positive and Negative Affect Schedule (PANAS) were completed at three lab visits. Participants with higher average DERS scores reported greater negative affect at lab visits. When a participant reported a DERS score at a lab visit higher than their individual average, they also reported higher negative affect at that lab visit. Participants with higher baseline DERS scores reported more labile negative affect during EMA than those with lower baseline DERS scores, and they also reported a higher maximum level of negative affect during EMA. Overall, the findings suggest that changes in emotion regulation are associated with negative affect and that emotion regulation ability is related to both the intensity and lability of negative affect. A better understanding of momentary changes in emotion regulation and negative affect may lead to improved interventions for preventing substance use relapse.

Taking off the training wheels: Measuring auditory P3 during outdoor cycling using an active wet EEG system.

PubMed

Scanlon, Joanna E M; Townsend, Kimberley A; Cormier, Danielle L; Kuziek, Jonathan W P; Mathewson, Kyle E

2017-12-14

Mobile EEG allows the investigation of brain activity in increasingly complex environments. In this study, EEG equipment was adapted for use and transportation in a backpack while cycling. Participants performed an auditory oddball task while cycling outside and sitting in an isolated chamber inside the lab. Cycling increased EEG noise and marginally diminished alpha amplitude. However, this increased noise did not influence the ability to measure reliable event related potentials (ERP). The P3 was similar in topography, and morphology when outside on the bike, with a lower amplitude in the outside cycling condition. There was only a minor decrease in the statistical power to measure reliable ERP effects. Unexpectedly, when biking outside significantly decreased P2 and increased N1 amplitude were observed when evoked by both standards and targets compared with sitting in the lab. This may be due to attentional processes filtering the overlapping sounds between the tones used and similar environmental frequencies. This study established methods for mobile recording of ERP signals. Future directions include investigating auditory P2 filtering inside the laboratory. Copyright © 2017. Published by Elsevier B.V.

The Influence of Tablet PCs on Students' Use of Multiple Representations in Lab Reports

NASA Astrophysics Data System (ADS)

Guelman, Clarisa Bercovich; De Leone, Charles; Price, Edward

2009-11-01

This study examined how different tools influenced students' use of representations in the Physics laboratory. In one section of a lab course, every student had a Tablet PC that served as a digital-ink based lab notebook. Students could seamlessly create hand-drawn graphics and equations, and write lab reports on the same computer used for data acquisition, simulation, and analysis. In another lab section, students used traditional printed lab guides, kept paper notebooks, and then wrote lab reports on regular laptops. Analysis of the lab reports showed differences between the sections' use of multiple representations, including an increased use of diagrams and equations by the Tablet users.

Product Assurance for Spaceflight Hardware

NASA Technical Reports Server (NTRS)

Monroe, Mike

1995-01-01

This report contains information about the tasks I have completed and the valuable experience I have gained at NASA. The report is divided into two different sections followed by a program summary sheet. The first section describes the two reports I have completed for the Office of Mission Assurance (OMA). I describe the approach and the resources and facilities used to complete each report. The second section describes my experience working in the Receipt Inspection/Quality Assurance Lab (RI/QA). The first report described is a Product Assurance Plan for the Gas Permeable Polymer Materials (GPPM) mission. The purpose of the Product Assurance Plan is to define the various requirements which are to be met through completion of the GPPM mission. The GPPM experiment is a space payload which will be flown in the shuttle's SPACEHAB module. The experiment will use microgravity to enable production of complex polymeric gas permeable materials. The second report described in the first section is a Fracture Analysis for the Mir Environmental Effects Payload (MEEP). The Fracture Analysis report is a summary of the fracture control classifications for all structural elements of the MEEP. The MEEP hardware consists of four experiment carriers, each of which contains an experiment container holding a passive experiment. The MEEP hardware will be attached to the cargo bay of the space shuttle. It will be transferred by Extravehicular Activity and mounted on the Mir space station. The second section of this report describes my experiences in the RVQA lab. I listed the different equipment I used at the lab and their functions. I described the extensive inspection process that must be completed for spaceflight hardware. Included, at the end of this section, are pictures of most of the equipment used in the lab. There is a summary sheet located at the end of this report. It briefly describes the valuable experience I have gained at NASA this summer and what I will be able to take with me as I return to college. I briefly discuss the experiences I mentioned in the previous three paragraphs along with training classes I attended and courses I completed at the Learning Lab.

Group Size Effect on Cooperation in One-Shot Social Dilemmas II: Curvilinear Effect.

PubMed

Capraro, Valerio; Barcelo, Hélène

2015-01-01

In a world in which many pressing global issues require large scale cooperation, understanding the group size effect on cooperative behavior is a topic of central importance. Yet, the nature of this effect remains largely unknown, with lab experiments insisting that it is either positive or negative or null, and field experiments suggesting that it is instead curvilinear. Here we shed light on this apparent contradiction by considering a novel class of public goods games inspired to the realistic scenario in which the natural output limits of the public good imply that the benefit of cooperation increases fast for early contributions and then decelerates. We report on a large lab experiment providing evidence that, in this case, group size has a curvilinear effect on cooperation, according to which intermediate-size groups cooperate more than smaller groups and more than larger groups. In doing so, our findings help fill the gap between lab experiments and field experiments and suggest concrete ways to promote large scale cooperation among people.

Analytic and subjective assessments of operator workload imposed by communications tasks in transport aircraft

NASA Technical Reports Server (NTRS)

Eckel, J. S.; Crabtree, M. S.

1984-01-01

Analytical and subjective techniques that are sensitive to the information transmission and processing requirements of individual communications-related tasks are used to assess workload imposed on the aircrew by A-10 communications requirements for civilian transport category aircraft. Communications-related tasks are defined to consist of the verbal exchanges between crews and controllers. Three workload estimating techniques are proposed. The first, an information theoretic analysis, is used to calculate bit values for perceptual, manual, and verbal demands in each communication task. The second, a paired-comparisons technique, obtains subjective estimates of the information processing and memory requirements for specific messages. By combining the results of the first two techniques, a hybrid analytical scale is created. The third, a subjective rank ordering of sequences of communications tasks, provides an overall scaling of communications workload. Recommendations for future research include an examination of communications-induced workload among the air crew and the development of simulation scenarios.

Report on all ARRA Funded Technical Work

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

2013-10-05

The main focus of this American Recovery and Reinvestment Act of 2009 (ARRA) funded project was to design an energy efficient carbon capture and storage (CCS) process using the Recipients membrane system for H{sub 2} separation and CO{sub 2} capture. In the ARRA-funded project, the Recipient accelerated development and scale-up of ongoing hydrogen membrane technology research and development (R&D). Specifically, this project focused on accelerating the current R&D work scope of the base program-funded project, involving lab scale tests, detail design of a 250 lb/day H{sub 2} process development unit (PDU), and scale-up of membrane tube and coating manufacturing. Thismore » project scope included the site selection and a Front End Engineering Design (FEED) study of a nominally 4 to 10 ton-per-day (TPD) Pre-Commercial Module (PCM) hydrogen separation membrane system. Process models and techno-economic analysis were updated to include studies on integration of this technology into an Integrated Gasification Combined Cycle (IGCC) power generation system with CCS.« less

A Reduced Order Model for Whole-Chip Thermal Analysis of Microfluidic Lab-on-a-Chip Systems

PubMed Central

Wang, Yi; Song, Hongjun; Pant, Kapil

2013-01-01

This paper presents a Krylov subspace projection-based Reduced Order Model (ROM) for whole microfluidic chip thermal analysis, including conjugate heat transfer. Two key steps in the reduced order modeling procedure are described in detail, including (1) the acquisition of a 3D full-scale computational model in the state-space form to capture the dynamic thermal behavior of the entire microfluidic chip; and (2) the model order reduction using the Block Arnoldi algorithm to markedly lower the dimension of the full-scale model. Case studies using practically relevant thermal microfluidic chip are undertaken to establish the capability and to evaluate the computational performance of the reduced order modeling technique. The ROM is compared against the full-scale model and exhibits good agreement in spatiotemporal thermal profiles (<0.5% relative error in pertinent time scales) and over three orders-of-magnitude acceleration in computational speed. The salient model reusability and real-time simulation capability renders it amenable for operational optimization and in-line thermal control and management of microfluidic systems and devices. PMID:24443647

The secondary drying and the fate of organic solvents for spray dried dispersion drug product.

PubMed

Hsieh, Daniel S; Yue, Hongfei; Nicholson, Sarah J; Roberts, Daniel; Schild, Richard; Gamble, John F; Lindrud, Mark

2015-05-01

To understand the mechanisms of secondary drying of spray-dried dispersion (SDD) drug product and establish a model to describe the fate of organic solvents in such a product. The experimental approach includes characterization of the SDD particles, drying studies of SDD using an integrated weighing balance and mass spectrometer, and the subsequent generation of the drying curve. The theoretical approach includes the establishment of a Fickian diffusion model. The kinetics of solvent removal during secondary drying from the lab scale to a bench scale follows Fickian diffusion model. Excellent agreement is obtained between the experimental data and the prediction from the modeling. The diffusion process is dependent upon temperature. The key to a successful scale up of the secondary drying is to control the drying temperature. The fate of primary solvents including methanol and acetone, and their potential impurity such as benzene can be described by the Fickian diffusion model. A mathematical relationship based upon the ratio of diffusion coefficient was established to predict the benzene concentration from the fate of the primary solvent during the secondary drying process.

Exoplanet Coronagraph Shaped Pupil Masks and Laboratory Scale Star Shade Masks: Design, Fabrication and Characterization

NASA Technical Reports Server (NTRS)

Balasubramanian, Kunjithapatha; White, Victor; Yee, Karl; Echternach, Pierre; Muller, Richard; Dickie, Matthew; Cady, Eric; Mejia Prada, Camilo; Ryan, Daniel; Poberezhskiy, Ilya;

Exoplanet coronagraph shaped pupil masks and laboratory scale star shade masks: design, fabrication and characterization

NASA Astrophysics Data System (ADS)

Balasubramanian, Kunjithapatham; White, Victor; Yee, Karl; Echternach, Pierre; Muller, Richard; Dickie, Matthew; Cady, Eric; Mejia Prada, Camilo; Ryan, Daniel; Poberezhskiy, Ilya; Zhou, Hanying; Kern, Brian; Riggs, A. J.; Zimmerman, Neil T.; Sirbu, Dan; Shaklan, Stuart; Kasdin, Jeremy

2015-09-01

Star light suppression technologies to find and characterize faint exoplanets include internal coronagraph instruments as well as external star shade occulters. Currently, the NASA WFIRST-AFTA mission study includes an internal coronagraph instrument to find and characterize exoplanets. Various types of masks could be employed to suppress the host star light to about 10-9 level contrast over a broad spectrum to enable the coronagraph mission objectives. Such masks for high contrast internal coronagraphic imaging require various fabrication technologies to meet a wide range of specifications, including precise shapes, micron scale island features, ultra-low reflectivity regions, uniformity, wave front quality, achromaticity, etc. We present the approaches employed at JPL to produce pupil plane and image plane coronagraph masks by combining electron beam, deep reactive ion etching, and black silicon technologies with illustrative examples of each, highlighting milestone accomplishments from the High Contrast Imaging Testbed (HCIT) at JPL and from the High Contrast Imaging Lab (HCIL) at Princeton University. We also present briefly the technologies applied to fabricate laboratory scale star shade masks.

Deep Submillimeter and Radio Observations in the SSA22 Field. I. Powering Sources and the Lyα Escape Fraction of Lyα Blobs

NASA Astrophysics Data System (ADS)

Ao, Y.; Matsuda, Y.; Henkel, C.; Iono, D.; Alexander, D. M.; Chapman, S. C.; Geach, J.; Hatsukade, B.; Hayes, M.; Hine, N. K.; Kato, Y.; Kawabe, R.; Kohno, K.; Kubo, M.; Lehnert, M.; Malkan, M.; Menten, K. M.; Nagao, T.; Norris, R. P.; Ouchi, M.; Saito, T.; Tamura, Y.; Taniguchi, Y.; Umehata, H.; Weiss, A.

2017-12-01

We study the heating mechanisms and Lyα escape fractions of 35 Lyα blobs (LABs) at z ≈ 3.1 in the SSA22 field. Dust continuum sources have been identified in 11 of the 35 LABs, all with star formation rates (SFRs) above 100 M ⊙ yr-1. Likely radio counterparts are detected in 9 out of 29 investigated LABs. The detection of submillimeter dust emission is more linked to the physical size of the Lyα emission than to the Lyα luminosities of the LABs. A radio excess in the submillimeter/radio-detected LABs is common, hinting at the presence of active galactic nuclei. Most radio sources without X-ray counterparts are located at the centers of the LABs. However, all X-ray counterparts avoid the central regions. This may be explained by absorption due to exceptionally large column densities along the line-of-sight or by LAB morphologies, which are highly orientation dependent. The median Lyα escape fraction is about 3% among the submillimeter-detected LABs, which is lower than a lower limit of 11% for the submillimeter-undetected LABs. We suspect that the large difference is due to the high dust attenuation supported by the large SFRs, the dense large-scale environment as well as large uncertainties in the extinction corrections required to apply when interpreting optical data.

Inhibition Plasticity in Older Adults: Practice and Transfer Effects Using a Multiple Task Approach.

PubMed

Wilkinson, Andrea J; Yang, Lixia

2016-01-01

OBJECTIVE. To examine plasticity of inhibition, as indexed by practice effects of inhibition tasks and the associated transfer effects, using a multiple task approach in healthy older adults. METHOD. Forty-eight healthy older adults were evenly assigned to either a practice group or a no-contact control group. All participants completed pretest (2.5 hours) and posttest (2 hours) sessions, with a 2-week interval in between. During the 2-week interval, only the practice group completed six 30-minute practice sessions (three sessions per week for two consecutive weeks) of three lab-based inhibition tasks. RESULTS. All three inhibition tasks demonstrated significant improvement across practice sessions, suggesting practice-induced plasticity. The benefit, however, only transferred to near-near tasks. The results are inconclusive with regard to the near-far and far-far transfer effects. DISCUSSION. This study further extends literature on practice effects of inhibition in older adults by using a multiple task approach. Together with previous work, the current study suggests that older adults are able to improve inhibition performance through practice and transfer the practice gains to tasks that overlap in both target cognitive ability and task structure (i.e., near-near tasks).

Inhibition Plasticity in Older Adults: Practice and Transfer Effects Using a Multiple Task Approach

PubMed Central

Wilkinson, Andrea J.; Yang, Lixia

2016-01-01

Objective. To examine plasticity of inhibition, as indexed by practice effects of inhibition tasks and the associated transfer effects, using a multiple task approach in healthy older adults. Method. Forty-eight healthy older adults were evenly assigned to either a practice group or a no-contact control group. All participants completed pretest (2.5 hours) and posttest (2 hours) sessions, with a 2-week interval in between. During the 2-week interval, only the practice group completed six 30-minute practice sessions (three sessions per week for two consecutive weeks) of three lab-based inhibition tasks. Results. All three inhibition tasks demonstrated significant improvement across practice sessions, suggesting practice-induced plasticity. The benefit, however, only transferred to near-near tasks. The results are inconclusive with regard to the near-far and far-far transfer effects. Discussion. This study further extends literature on practice effects of inhibition in older adults by using a multiple task approach. Together with previous work, the current study suggests that older adults are able to improve inhibition performance through practice and transfer the practice gains to tasks that overlap in both target cognitive ability and task structure (i.e., near-near tasks). PMID:26885407

Production of polyhydroxyalkanoates (PHA) by bacterial consortium from excess sludge fermentation liquid at laboratory and pilot scales.

PubMed

Jia, Qianqian; Xiong, Huilei; Wang, Hui; Shi, Hanchang; Sheng, Xinying; Sun, Run; Chen, Guoqiang

2014-11-01

The generation of polyhydroxyalkanoates (PHA) from excess sludge fermentation liquid (SFL) was studied at lab and pilot scale. A PHA-accumulated bacterial consortium (S-150) was isolated from activated sludge using simulated SFL (S-SFL) contained high concentration volatile fatty acids (VFA) and nitrogen. The maximal PHA content accounted for 59.18% in S-SFL and dropped to 23.47% in actual SFL (L-SFL) of the dry cell weight (DCW) at lab scale. The pilot-scale integrated system comprised an anaerobic fermentation reactor (AFR), a ceramic membrane system (CMS) and a PHA production bio-reactor (PHAR). The PHA content from pilot-scale SFL (P-SFL) finally reached to 59.47% DCW with the maximal PHA yield coefficient (YP/S) of 0.17 g PHA/g COD. The results indicated that VFA-containing SFL was suitable for PHA production. The adverse impact of excess nitrogen and non-VFAs in SFL might be eliminated by pilot-scale domestication, which might resulted in community structure optimization and substrate selective ability improvement of S-150. Copyright © 2014 Elsevier Ltd. All rights reserved.

End-effects-regime in full scale and lab scale rocket nozzles

NASA Astrophysics Data System (ADS)

Rojo, Raymundo; Tinney, Charles; Baars, Woutijn; Ruf, Joseph

2014-11-01

Modern rockets utilize a thrust-optimized parabolic-contour design for their nozzles for its high performance and reliability. However, the evolving internal flow structures within these high area ratio rocket nozzles during start up generate a powerful amount of vibro-acoustic loads that act on the launch vehicle. Modern rockets must be designed to accommodate for these heavy loads or else risk a catastrophic failure. This study quantifies a particular moment referred to as the ``end-effects regime,'' or the largest source of vibro-acoustic loading during start-up [Nave & Coffey, AIAA Paper 1973-1284]. Measurements from full scale ignitions are compared with aerodynamically scaled representations in a fully anechoic chamber. Laboratory scale data is then matched with both static and dynamic wall pressure measurements to capture the associating shock structures within the nozzle. The event generated during the ``end-effects regime'' was successfully reproduced in the both the lab-scale models, and was characterized in terms of its mean, variance and skewness, as well as the spectral properties of the signal obtained by way of time-frequency analyses.

Development of Guided Inquiry-Based Student Lab Worksheet on the Making of Pineapple Flavoring

NASA Astrophysics Data System (ADS)

Dwiyanti, G.; Suryatna, A.; Taibah, I.

2017-02-01

The aim of this research was to develop guided inquiry based student lab worksheet on making pineapple flavour and knowing the quality of worksheet that is being developed. Research methods that is being conducted is research and development that is limited by a preliminary studies (literature studies, field surveys, and preparation of the initial product) and development of the model (within limited testing). The results from analyze the books sources and fields survey showed that the characteristic of esterification lab worksheet that currently available still in the direct instruction form (cookbook). The optimization result of making pineapple flavour experiment that was conducted are the ethanol volume 3 mL, butyric acid volume 2 mL, sulfuric acid 5 drops, saturated NaHCO3 solution volume 9 mL, and temperature of heating was 80 °C. The characteristic of guided inquiry based student lab worksheet that was developed contained phenomenon and instructions that suitable with inquiry stages to guide the students in doing the experiment of making pineapple flavour. The evaluation of designated teachers and lecturers of the developed student worksheet were very good (96,08%). Lab-experiment feasibility achieved by using guided inquiry based student lab worksheets that is being developed based on the inquiry stages that conducted by student were found very good (97,50%) and accomplishment based on students’ answer of the tasks in the worksheet were found very good (83,84%). Students’ responses of the experiments using the developed worksheet are found very good (81,84%).

Online Learning Self-Efficacy in Students with and without Online Learning Experience

ERIC Educational Resources Information Center

Zimmerman, Whitney Alicia; Kulikowich, Jonna M.

2016-01-01

A need was identified for an instrument to measure online learning self-efficacy, which encompassed the wide variety of tasks required of successful online students. The Online Learning Self-Efficacy Scale (OLSES) was designed to include tasks required of students enrolled in paced online courses at one university. In the present study, the…

Affordable Imaging Lab for Noninvasive Analysis of Biomass and Early Vigour in Cereal Crops

PubMed Central

2018-01-01

Plant phenotyping by imaging allows automated analysis of plants for various morphological and physiological traits. In this work, we developed a low-cost RGB imaging phenotyping lab (LCP lab) for low-throughput imaging and analysis using affordable imaging equipment and freely available software. LCP lab comprising RGB imaging and analysis pipeline is set up and demonstrated with early vigour analysis in wheat. Using this lab, a few hundred pots can be photographed in a day and the pots are tracked with QR codes. The software pipeline for both imaging and analysis is built from freely available software. The LCP lab was evaluated for early vigour analysis of five wheat cultivars. A high coefficient of determination (R2 0.94) was obtained between the dry weight and the projected leaf area of 20-day-old wheat plants and R2 of 0.9 for the relative growth rate between 10 and 20 days of plant growth. Detailed description for setting up such a lab is provided together with custom scripts built for imaging and analysis. The LCP lab is an affordable alternative for analysis of cereal crops when access to a high-throughput phenotyping facility is unavailable or when the experiments require growing plants in highly controlled climate chambers. The protocols described in this work are useful for building affordable imaging system for small-scale research projects and for education. PMID:29850536

Differential resistance of drinking water bacterial populations to monochloramine disinfection.

PubMed

Chiao, Tzu-Hsin; Clancy, Tara M; Pinto, Ameet; Xi, Chuanwu; Raskin, Lutgarde

2014-04-01

The impact of monochloramine disinfection on the complex bacterial community structure in drinking water systems was investigated using culture-dependent and culture-independent methods. Changes in viable bacterial diversity were monitored using culture-independent methods that distinguish between live and dead cells based on membrane integrity, providing a highly conservative measure of viability. Samples were collected from lab-scale and full-scale drinking water filters exposed to monochloramine for a range of contact times. Culture-independent detection of live cells was based on propidium monoazide (PMA) treatment to selectively remove DNA from membrane-compromised cells. Quantitative PCR (qPCR) and pyrosequencing of 16S rRNA genes was used to quantify the DNA of live bacteria and characterize the bacterial communities, respectively. The inactivation rate determined by the culture-independent PMA-qPCR method (1.5-log removal at 664 mg·min/L) was lower than the inactivation rate measured by the culture-based methods (4-log removal at 66 mg·min/L). Moreover, drastic changes in the live bacterial community structure were detected during monochloramine disinfection using PMA-pyrosequencing, while the community structure appeared to remain stable when pyrosequencing was performed on samples that were not subject to PMA treatment. Genera that increased in relative abundance during monochloramine treatment include Legionella, Escherichia, and Geobacter in the lab-scale system and Mycobacterium, Sphingomonas, and Coxiella in the full-scale system. These results demonstrate that bacterial populations in drinking water exhibit differential resistance to monochloramine, and that the disinfection process selects for resistant bacterial populations.

Remote-controlled optics experiment for supporting senior high school and undergraduate teaching

NASA Astrophysics Data System (ADS)

Choy, S. H.; Jim, K. L.; Mak, C. L.; Leung, C. W.

2017-08-01

This paper reports the development of a remote laboratory (RemoteLab) platform for practising technologyenhanced learning of optics. The development of RemoteLab enhances students' understanding of experimental methodologies and outcomes, and enable students to conduct experiments everywhere at all times. While the initial goal of the system was for physics major undergradutes, the sytem was also made available for senior secondary school students. To gauge the impact of the RemoteLab, we evaluated two groups of students, which included 109 physics 1st-year undergraduates and 11 students from a local secondary school. After the experiments, evaluation including questionnaire survey and interviews were conducted to collect data on students' perceptions on RemoteLab and implementation issues related to the platform. The surveys focused on four main topics, including user interface, experiment setup, booking system and learning process. The survey results indicated that most of the participants' views towards RemoteLab was positive.

The impact of interoperability of electronic health records on ambulatory physician practices: a discrete-event simulation study.

PubMed

Zhou, Yuan; Ancker, Jessica S; Upadhye, Mandar; McGeorge, Nicolette M; Guarrera, Theresa K; Hegde, Sudeep; Crane, Peter W; Fairbanks, Rollin J; Bisantz, Ann M; Kaushal, Rainu; Lin, Li

2013-01-01

The effect of health information technology (HIT) on efficiency and workload among clinical and nonclinical staff has been debated, with conflicting evidence about whether electronic health records (EHRs) increase or decrease effort. None of this paper to date, however, examines the effect of interoperability quantitatively using discrete event simulation techniques. To estimate the impact of EHR systems with various levels of interoperability on day-to-day tasks and operations of ambulatory physician offices. Interviews and observations were used to collect workflow data from 12 adult primary and specialty practices. A discrete event simulation model was constructed to represent patient flows and clinical and administrative tasks of physicians and staff members. High levels of EHR interoperability were associated with reduced time spent by providers on four tasks: preparing lab reports, requesting lab orders, prescribing medications, and writing referrals. The implementation of an EHR was associated with less time spent by administrators but more time spent by physicians, compared with time spent at paper-based practices. In addition, the presence of EHRs and of interoperability did not significantly affect the time usage of registered nurses or the total visit time and waiting time of patients. This paper suggests that the impact of using HIT on clinical and nonclinical staff work efficiency varies, however, overall it appears to improve time efficiency more for administrators than for physicians and nurses.

Methodological possibilities for the solution of new tasks for “Thermophysics of Power Units” Department of SPbPU

NASA Astrophysics Data System (ADS)

Sapozhnikov, S. Z.; Mityakov, V. Yu; Mityakov, A. V.; Gusakov, A. A.

2017-11-01

“Thermophysics of Power Units” Department is based on pre-existed “Thermodynamics and Heat Transfer” and “Reactors and Boilers” Departments. The main goal of the new department (in addition to training students in basic courses of Thermodynamics, Heat and Mass Transfer, Fluid Mechanics, Metrology and Thermal Measurement) has become a new master’s profile “Thermal Engineering, Energy Audit and Energy Service”. It required radical restructuring of the whole educational process, and in the first place - its material resources and equipment. Over the last two years “Heat and Mass Transfer” lab and “Wind tunnel” lab are upgraded, and “Metrology and Thermophysical Measurement” lab is newly created. Tutorials of new generation are changing significantly the structure of our main courses. The members of our scientific group (2 - 6 year students) actively engaged in the work process. Now we hope to see the best of them among our future postgraduates.

a Matter of Confidence: Gender Differences in Attitudes Toward Engaging in Lab and Course Work in Undergraduate Engineering

NASA Astrophysics Data System (ADS)

Micari, Marina; Pazos, Pilar; Hartmann, Mitra J. Z.

Although there has been a great deal of research on women's experiences in engineering study, there has been little attempt to connect experiential factors to performance in both course and lab. This two-phase study investigated gender differences in undergraduates' experiences in a fluid mechanics course as well as the relationship between experiential factors and student performance in that course. One hundred forty-seven students at a Midwestern research university completed questionnaires related to course experience and perceived engagement. Data were also collected on final grade for 89 students in the second round of data collection. Relative to men, women reported less confidence that they could avoid mistakes in the lab, less experience with mechanical items, less perceived ability in engineering relative to classmates, and less perceived skill in tasks requiring navigation or maneuvering through space. Feelings of engagement were related to grade, but no gender differences were found in either engagement or grade.

Conversion of Small Algal Oil Sample to JP-8

DTIC Science & Technology

2012-01-01

cracking of Algal Oil to SPK Hydroprocessing Lab Plant uop Nitrogen Hydrogen Product ., __ Small Scale Lab Hydprocessing plant - Down flow trickle ... bed configuration - Capable of retaining 25 cc of catalyst bed Meter UOP ·CONFIDENTIAL File Number The catalytic deoxygenation stage of the...content which combined with the samples acidity, is a challenge to reactor metallurgy. None the less, an attempt was made to convert this sample to

First Light for BOSS - A New Kind of Search for Dark Energy | Berkeley

Science.gov Websites

in the clumping of invisible dark matter. Comparing these scales at different eras makes it possible Web People Close About the Lab Leadership/Organization Calendar News Center Today At Berkeley Lab News Preuss, (510) 486-6249 On the night of September 14 the largest program in the Sloan Digital Sky Survey

Impact of REM sleep on distortions of self-concept, mood and memory in depressed/anxious participants

PubMed Central

McNamara, Patrick; Auerbach, Sanford; Johnson, Patricia; Harris, Erica; Doros, Gheorghe

2009-01-01

Introduction: We tested the hypothesis that REM sleep contributes to core features of cognitive dysfunction of anxious depression including negative self-appraisals, biased memory processing and unpleasant dream content. Methods: After a habituation night in a sleep lab, a convenience sample of 35 healthy college students and 20 depressed/anxious students were awakened 10 minutes into a REM sleep episode and then 10 minutes into a NREM sleep episode. Awakenings were counterbalanced to control circadian effects. After each awakening participants reported a dream and then completed memory recall, mood and self-appraisal tasks. Results: Self-appraisals of depressed/anxious participants were significantly less positive and significantly more negative after awakenings from REM sleep vs NREM sleep. Appraisal of the REM sleep dream self was negative for depressed/anxious subjects only. Recall of negative memories was significantly more frequent after REM vs NREM sleep awakenings for both depress/anxious and healthy participants. REM sleep dreams were associated with greater frequencies of negative emotion, greater aggression and victimization rates than dreams in NREM sleep for depressed/anxious participants. Limitations: Depressed/anxious participants were classified as such on the basis of mood scales rather than clinical interview. All participants were drawn from a volunteer college student population and thus our results may not be applicable to some elderly clinical populations. Conclusions: REM appears to facilitate cognitive distortions of anxious depression. PMID:19631989

Impact of REM sleep on distortions of self-concept, mood and memory in depressed/anxious participants.

PubMed

McNamara, Patrick; Auerbach, Sanford; Johnson, Patricia; Harris, Erica; Doros, Gheorghe

2010-05-01

We tested the hypothesis that REM sleep contributes to core features of cognitive dysfunction of anxious depression including negative self-appraisals, biased memory processing and unpleasant dream content. After a habituation night in a sleep lab, a convenience sample of 35 healthy college students and 20 depressed/anxious students were awakened 10 min into a REM sleep episode and then 10 min into a NREM sleep episode. Awakenings were counterbalanced to control circadian effects. After each awakening participants reported a dream and then completed memory recall, mood and self-appraisal tasks. Self-appraisals of depressed/anxious participants were significantly less positive and significantly more negative after awakenings from REM sleep vs NREM sleep. Appraisal of the REM sleep dream self was negative for depressed/anxious subjects only. Recall of negative memories was significantly more frequent after REM vs NREM sleep awakenings for both depress/anxious and healthy participants. REM sleep dreams were associated with greater frequencies of negative emotion, greater aggression and victimization rates than dreams in NREM sleep for depressed/anxious participants. Depressed/anxious participants were classified as such on the basis of mood scales rather than clinical interview. All participants were drawn from a volunteer college student population and thus our results may not be applicable to some elderly clinical populations. REM appears to facilitate cognitive distortions of anxious depression. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Quantum Materials at the Nanoscale - Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, Stephen Lance

The central aim of the Quantum Materials at the Nanoscale (QMN) cluster was to understand and control collective behavior involving the interplay of spins, orbitals, and charges, which governs many scientifically interesting and technologically important phenomena in numerous complex materials. Because these phenomena involve various competing interactions, and influence properties on many different length and energy scales in complex materials, tackling this important area of study motivated a collaborative effort that combined the diverse capabilities of QMN cluster experimentalists, the essential theoretical analysis provided by QMN cluster theorists, and the outstanding facilities and staff of the FSMRL. During the fundingmore » period 2007-2014, the DOE cluster grant for the Quantum Materials at the Nanoscale (QMN) cluster supported, at various times, 15 different faculty members (14 in Physics and 1 in Materials Science and Engineering), 7 postdoctoral research associates, and 57 physics and materials science PhD students. 41 of these PhD students have since graduated and have gone on to a variety of advanced technical positions at universities, industries, and national labs: 25 obtained postdoctoral positions at universities (14), industrial labs (2 at IBM), DOE national facilities (3 at Argonne National Laboratory, 1 at Brookhaven National Lab, 1 at Lawrence Berkeley National Lab, and 1 at Sandia National Lab), and other federal facilities (2 at NIST); 13 took various industrial positions, including positions at Intel (5), Quantum Design (1), Lasque Industries (1), Amazon (1), Bloomberg (1), and J.P. Morgan (1). Thus, the QMN grant provided the essential support for training a large number of technically advanced personnel who have now entered key national facilities, industries, and institutions. Additionally, during the period 2007-2015, the QMN cluster produced 159 publications (see pages 14-23), including 23 papers published in Physical Review Letters; 16 papers in Nature, Nature Physics, Nature Materials, or Nature Communications; 4 papers in Science, and 8 papers in Applied Physics Letters. In this report, we provide some key highlights of the collaborative projects in which the QMN cluster members have been involved since 2007.« less

Characterization of the SRNL-Washed tank 51 sludge batch 9 qualification sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pareizs, J. M.

2016-01-01

Savannah River National Laboratory (SRNL) personnel have been requested to qualify the next sludge batch (Sludge Batch 9 – SB9) for processing at the Defense Waste Processing Facility (DWPF). To accomplish this task, Savannah River Remediation (SRR) sent SRNL a 3-L sample of Tank 51H slurry to be characterized, washed, and then used in a lab-scale demonstration of the DWPF flowsheet (after combining with Tank 40H sludge). SRNL has washed the Tank 51H sample per the Tank Farm washing strategy as of October 20, 2015. A part of the qualification process is extensive radionuclide and chemical characterization of the SRNL-washedmore » Tank 51H slurry. This report documents the chemical characterization of the washed slurry; radiological characterization is in progress and will be documented in a separate report. The analytical results of this characterization are comparable to the Tank Farm projections. Therefore, it is recommended that SRNL use this washed slurry for the ongoing SB9 qualification activities.« less

Effects of statistical learning on the acquisition of grammatical categories through Qur'anic memorization: A natural experiment.

PubMed

Zuhurudeen, Fathima Manaar; Huang, Yi Ting

2016-03-01

Empirical evidence for statistical learning comes from artificial language tasks, but it is unclear how these effects scale up outside of the lab. The current study turns to a real-world test case of statistical learning where native English speakers encounter the syntactic regularities of Arabic through memorization of the Qur'an. This unique input provides extended exposure to the complexity of a natural language, with minimal semantic cues. Memorizers were asked to distinguish unfamiliar nouns and verbs based on their co-occurrence with familiar pronouns in an Arabic language sample. Their performance was compared to that of classroom learners who had explicit knowledge of pronoun meanings and grammatical functions. Grammatical judgments were more accurate in memorizers compared to non-memorizers. No effects of classroom experience were found. These results demonstrate that real-world exposure to the statistical properties of a natural language facilitates the acquisition of grammatical categories. Copyright © 2015 Elsevier B.V. All rights reserved.

Remote sensing from the desktop up, a students's personal stairway to space (Invited)

NASA Astrophysics Data System (ADS)

Church, W.

2013-12-01

Doing science with real-time quantitative experiments is becoming more and more affordable and accessible. Because lab equipment is more affordable and accessible, many universities are using lab class models wherein students conduct their experiments in informal settings such as the dorm, outside, or other places throughout the campus. Students are doing real-time measurements homework outside of class. By liberating experiments from facilities, the hope is to give students more experimental science opportunities. The challenge is support. In lab settings, instructors and peers can help students if they have trouble with the steps of assembling their experimental set-up, configuring the data acquisition software, conducting the real-time measurement and doing the analysis. Students working on their own in a dorm do not benefit from this support. Furthermore, when students are given the open ended experimental task of designing their own measurement system, they may need more guidance. In this poster presentation, I will articulate a triangle model to support students through the task of finding the necessary resources to design and build a mission to space. In the triangle model, students have access to base layer concept and skill resources to help them build their experiment. They then have access to middle layer mini-experiments to help them configure and test their experimental set-up. Finally, they have a motivating real-time experiment. As an example of this type of resource used in practice, I will have a balloon science remote sensing project as a stand-in for a balloon mission to 100,000 feet. I will use an Arduino based DAQ system and XBee modules for wireless data transmission to a LabVIEW front-panel. I will attach the DAQ to a tethered balloon to conduct a real-time microclimate experiment in the Moscone Center. Expanded microclimate studies can be the capstone project or can be a stepping-stone to space wherein students prepare a sensor package for a weather balloon launch to 100,000 feet.

Hypersonic Vehicle Propulsion System Simplified Model Development

NASA Technical Reports Server (NTRS)

Stueber, Thomas J.; Raitano, Paul; Le, Dzu K.; Ouzts, Peter

2007-01-01

This document addresses the modeling task plan for the hypersonic GN&C GRC team members. The overall propulsion system modeling task plan is a multi-step process and the task plan identified in this document addresses the first steps (short term modeling goals). The procedures and tools produced from this effort will be useful for creating simplified dynamic models applicable to a hypersonic vehicle propulsion system. The document continues with the GRC short term modeling goal. Next, a general description of the desired simplified model is presented along with simulations that are available to varying degrees. The simulations may be available in electronic form (FORTRAN, CFD, MatLab,...) or in paper form in published documents. Finally, roadmaps outlining possible avenues towards realizing simplified model are presented.

Webinar July 28: H2@Scale - A Potential Opportunity | News | NREL

Science.gov Websites

role of hydrogen at the grid scale and the efforts of a large, national lab team assembled to evaluate the potential of hydrogen to play a critical role in our energy future. Presenters will share facts

Construct and test scale model box culvert design project.

DOT National Transportation Integrated Search

2010-11-01

The research team at the University of New Mexicos (UNM) hydraulics lab designed, constructed, and : tested a 1:20 scale physical model of a proposed culvert in Jemez Springs, New Mexico. The culvert : design was developed by the New Mexico Depart...

Exploring cognitive complaints in schizophrenia: the subjective scale to investigate cognition in schizophrenia.

PubMed

Stip, E; Caron, J; Renaud, S; Pampoulova, T; Lecomte, Y

2003-01-01

While it has become commonplace to test the various components of memory in schizophrenia with paper-and-pencil or in-lab tasks, very little data exist on the subjective complaints of patients regarding their memory. Few instruments have been designed to collect systematically the complaints of patients with schizophrenia. We present a work in progress on the Subjective Scale to Investigate Cognition in Schizophrenia (SSTICS), a 21-item, Likert-type scale that is simple and easy to use. It allows a quantitative approach to the subjective and cognitive dimensions of schizophrenia. Stip constructed the scale based on a questionnaire covering several cognitive domains: memory (working memory, explicit long-term memory), attention (divided, distractibility, alertness, sustained), language, and praxia. We evaluated the psychometric properties of the SSTICS in a population of 114 French-speaking patients in Montreal. Patients were recruited in the community and assessed with the Structured Clinical Interview for DSM-III-R (SCID), the Positive and Negative Syndrome Scale (PANSS), and the Extrapyramidal Symptoms Rating Scale (ESRS). Cognition was measured using the Rey Auditory Verbal Learning Test (RAVLT) (long-term memory), Controlled Oral Word Association Test (verbal fluency), and Trails A and B. Preliminary analyses showed very good internal consistency for the global score (alpha=0.88), and alphas varying from 0.57 to 0.72 for the subscales. Stability over time was very good. The principal components analysis accounted for a multiple structure. Correlations between subjective scores and objective cognitive assessment were significant for several domains. Validation of the SSTICS needs to be completed through further exploration of the factorial structure and testing of the English version.

BLINKER: Automated Extraction of Ocular Indices from EEG Enabling Large-Scale Analysis

PubMed Central

Kleifges, Kelly; Bigdely-Shamlo, Nima; Kerick, Scott E.; Robbins, Kay A.

2017-01-01

Electroencephalography (EEG) offers a platform for studying the relationships between behavioral measures, such as blink rate and duration, with neural correlates of fatigue and attention, such as theta and alpha band power. Further, the existence of EEG studies covering a variety of subjects and tasks provides opportunities for the community to better characterize variability of these measures across tasks and subjects. We have implemented an automated pipeline (BLINKER) for extracting ocular indices such as blink rate, blink duration, and blink velocity-amplitude ratios from EEG channels, EOG channels, and/or independent components (ICs). To illustrate the use of our approach, we have applied the pipeline to a large corpus of EEG data (comprising more than 2000 datasets acquired at eight different laboratories) in order to characterize variability of certain ocular indicators across subjects. We also investigate dependence of ocular indices on task in a shooter study. We have implemented our algorithms in a freely available MATLAB toolbox called BLINKER. The toolbox, which is easy to use and can be applied to collections of data without user intervention, can automatically discover which channels or ICs capture blinks. The tools extract blinks, calculate common ocular indices, generate a report for each dataset, dump labeled images of the individual blinks, and provide summary statistics across collections. Users can run BLINKER as a script or as a plugin for EEGLAB. The toolbox is available at https://github.com/VisLab/EEG-Blinks. User documentation and examples appear at http://vislab.github.io/EEG-Blinks/. PMID:28217081

Evaluating the benefits of digital pathology implementation: Time savings in laboratory logistics.

PubMed

Baidoshvili, Alexi; Bucur, Anca; van Leeuwen, Jasper; van der Laak, Jeroen; Kluin, Philip; van Diest, Paul J

2018-06-20

The benefits of digital pathology for workflow improvement and thereby cost savings in pathology, at least partly outweighing investment costs, are increasingly recognized. Successful implementations in a variety of scenarios start to demonstrate cost benefits of digital pathology for both research and routine diagnostics, contributing to a sound business case encouraging further adoption. To further support new adopters, there is still a need for detailed assessment of the impact this technology has on the relevant pathology workflows with emphasis on time saving. To assess the impact of digital pathology adoption on logistic laboratory tasks (i.e. not including pathologists' time for diagnosis making) in LabPON, a large regional pathology laboratory in The Netherlands. To quantify the benefits of digitization we analyzed the differences between the traditional analog and new digital workflows, carried out detailed measurements of all relevant steps in key analog and digital processes, and compared time spent. We modeled and assessed the logistic savings in five workflows: (1) Routine diagnosis, (2) Multi-disciplinary meeting, (3) External revision requests, (4) Extra stainings and (5) External consultation. On average over 19 working hours were saved on a typical day by working digitally, with the highest savings in routine diagnosis and multi-disciplinary meeting workflows. By working digitally, a significant amount of time could be saved in a large regional pathology lab with a typical case mix. We also present the data in each workflow per task and concrete logistic steps to allow extrapolation to the context and case mix of other laboratories. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

The effects of using a portable music player on simulated driving performance and task-sharing strategies.

PubMed

Young, Kristie L; Mitsopoulos-Rubens, Eve; Rudin-Brown, Christina M; Lenné, Michael G

2012-07-01

This study examined the effects of performing scrollable music selection tasks using a portable music player (iPod Touch™) on simulated driving performance and task-sharing strategies, as evidenced through eye glance behaviour and secondary task performance. A total of 37 drivers (18-48 yrs) completed the PC-based MUARC Driver Distraction Test (DDT) while performing music selection tasks on an iPod Touch. Drivers' eye glance behaviour was examined using faceLAB eye tracking equipment. Results revealed that performing music search tasks while driving increased the amount of time that drivers spent with their eyes off the roadway and decreased their ability to maintain a constant lane position and time headway from a lead vehicle. There was also evidence, however, that drivers attempted to regulate their behaviour when distracted by decreasing their speed and taking a large number of short glances towards the device. Overall, results suggest that performing music search tasks while driving is problematic and steps to prohibit this activity should be taken. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Spatial and Temporal Variability in Biogenic Gas Accumulation and Release in The Greater Everglades at Multiple Scales of Measurement

NASA Astrophysics Data System (ADS)

McClellan, M. D.; Cornett, C.; Schaffer, L.; Comas, X.

2017-12-01

Wetlands play a critical role in the carbon (C) cycle by producing and releasing significant amounts of greenhouse biogenic gasses (CO2, CH4) into the atmosphere. Wetlands in tropical and subtropical climates (such as the Florida Everglades) have become of great interest in the past two decades as they account for more than 20% of the global peatland C stock and are located in climates that favor year-round C emissions. Despite the increase in research involving C emission from these types of wetlands, the spatial and temporal variability involving C production, accumulation and release is still highly uncertain, and is the focus of this research at multiple scales of measurement (i.e. lab, field and landscape). Spatial variability in biogenic gas content, build up and release, at both the lab and field scales, was estimated using a series of ground penetrating radar (GPR) surveys constrained with gas traps fitted with time-lapse cameras. Variability in gas content was estimated at the sub-meter scale (lab scale) within two extracted monoliths from different wetland ecosystems at the Disney wilderness Preserve (DWP) and the Blue Cypress Preserve (BCP) using high frequency GPR (1.2 GHz) transects across the monoliths. At the field scale (> 10m) changes in biogenic gas content were estimated using 160 MHz GPR surveys collected within 4 different emergent wetlands at the DWP. Additionally, biogenic gas content from the extracted monoliths was used to developed a landscape comparison of C accumulation and emissions for each different wetland ecosystem. Changes in gas content over time were estimated at the lab scale at high temporal resolution (i.e. sub-hourly) in monoliths from the BCP and Water Conservation Area 1-A. An autonomous rail system was constructed to estimate biogenic gas content variability within the wetland soil matrix using a series of continuous, uninterrupted 1.2 GHz GPR transects along the samples. Measurements were again constrained with an array of gas traps fitted with time-lapse cameras. This research seeks to better understand the spatial and temporal variability of biogenic gas content within wetlands from the Greater Everglades Watershed. Such understanding may help to identify potential hotspots (both in space and time) and their implication for the flux estimates used as input in climate models.

High Quality, Low Cost Bulk Gallium Nitride Substrates Grown by the Electrochemical Solution Growth Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seacrist, Michael

The objective of this project was to develop the Electrochemical Solution Growth (ESG) method conceived / patented at Sandia National Laboratory into a commercially viable bulk gallium nitride (GaN) growth process that can be scaled to low cost, high quality, and large area GaN wafer substrate manufacturing. The goal was to advance the ESG growth technology by demonstrating rotating seed growth at the lab scale and then transitioning process to prototype commercial system, while validating the GaN material and electronic / optical device quality. The desired outcome of the project is a prototype commercial process for US-based manufacturing of highmore » quality, large area, and lower cost GaN substrates that can drive widespread deployment of energy efficient GaN-based power electronic and optical devices. In year 1 of the project (Sept 2012 – Dec 2013) the overall objective was to demonstrate crystalline GaN growth > 100um on a GaN seed crystal. The development plan included tasks to demonstrate and implement a method for purifying reagent grade salts, develop the reactor 1 process for rotating seed Electrochemical Solution Growth (ESG) of GaN, grow and characterize ESG GaN films, develop a fluid flow and reaction chemistry model for GaN film growth, and design / build an improved growth reactor capable of scaling to 50mm seed diameter. The first year’s project objectives were met in some task areas including salt purification, film characterization, modeling, and reactor 2 design / fabrication. However, the key project objective of the growth of a crystalline GaN film on the seed template was not achieved. Amorphous film growth on the order of a few tenths of a micron has been detected with a film composition including Ga and N, plus several other impurities originating from the process solution and hardware. The presence of these impurities, particularly the oxygen, has inhibited the demonstration of crystalline GaN film growth on the seed template. However, the presence of both Ga and N at the growth surface indicates that the reactor hardware physics is all functioning properly; achieving film growth is a matter of controlling the chemistry at the interface. The impurities originating from the hardware are expected to be straightforward to eliminate. Activities were defined for an extension of budget period 1 to eliminate the undesired impurities originating from the reactor hardware and interfering with crystalline GaN film growth. The budget period 1 extension was negotiated during the 1st half of 2014. The budget period 1 extension spanned approximately from August 2014 to August 2015. The project objective for this extension period was to demonstrate at least 0.5um crystalline GaN film on a GaN seed in the lab scale reactor. The focus of the budget 1 extension period from August 2014 to August 2015 was to eliminate oxygen contamination interference with GaN film growth. The team procured the highest purity lowest oxygen salt for testing. Low oxygen crucible materials such as silicon carbide were installed and evaluated in the laboratory reactor. Growth experiments were performed with high purity salt, high purity hardware, and optimized oxide removal from the seed surface. Experiments were characterized with methods including UV inspection, profilometry, x-ray diffraction (XRD) to determine crystalline structure, optical and scanning electron microscopy, photoluminescence, x-ray photon spectroscopy (XPS), transmission electron microscopy (TEM), and secondary ion mass spectroscopy (SIMS). Despite successfully integrating the low oxygen materials in the laboratory reactor, the goal of depositing 0.5um of crystalline GaN on the MOCVD GaN seed was not met. Very thin (ca. 10nm) cubic phase GaN deposition was observed on the hexagonal MOCVD GaN seeds. But there was a competing etching reaction which was also observed and thought to be related to the presence of metallic lithium, a byproduct of the LiCl-KCl salt used as the process medium. The etching reaction could potentially be addressed by alternate salts not containing lithium, but would necessitate starting all over on the reactor and process design. Further, controlling the reaction of Ga and N in the bulk salt to favor deposition on the seed has proved to be very difficult and unlikely to be solved within the scope of this project in a manner consistent with the original objective for wafer or crystal scale thickness for GaN deposition on a GaN seed. Upon completion of the budget 1 extension period in August 2015 the project partners and DOE agreed to stop work on the project.« less

Xylo-Oligosaccharide Process Development, Composition, and Techno-Economic Analysis. Cooperative Research and Development Final Report, CRADA Number CRD-12-483

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shekiro, Joe; Elander, Richard

2015-12-01

The purpose of this cooperative work agreement between General Mills Inc. (GMI) and NREL is to determine the feasibility of producing a valuable food ingredient (xylo-oligosaccharides or XOS), a highly soluble fiber material, from agricultural waste streams, at an advantaged cost level relative to similar existing ingredients. The scope of the project includes pilot-scale process development (Task 1), compositional analysis (Task 2), and techno-economic analysis (Task 3).

The disruptive effect of lysozyme on the bacterial cell wall explored by an in-silico structural outlook.

PubMed

Primo, Emiliano D; Otero, Lisandro H; Ruiz, Francisco; Klinke, Sebastián; Giordano, Walter

2018-01-01

The bacterial cell wall, a structural unit of peptidoglycan polymer comprised of glycan strands consisting of a repeating disaccharide motif [N-acetylglucosamine (NAG) and N-acetylmuramylpentapeptide (NAM pentapeptide)], encases bacteria and provides structural integrity and protection. Lysozymes are enzymes that break down the bacterial cell wall and disrupt the bacterial life cycle by cleaving the linkage between the NAG and NAM carbohydrates. Lab exercises focused on the effects of lysozyme on the bacterial cell wall are frequently incorporated in biochemistry classes designed for undergraduate students in diverse fields as biology, microbiology, chemistry, agronomy, medicine, and veterinary medicine. Such exercises typically do not include structural data. We describe here a sequence of computer tasks designed to illustrate and reinforce both physiological and structural concepts involved in lysozyme effects on the bacterial cell-wall structure. This lab class usually lasts 3.5 hours. First, the instructor presents introductory concepts of the bacterial cell wall and the effect of lysozyme on its structure. Then, students are taught to use computer modeling to visualize the three-dimensional structure of a lysozyme in complex with bacterial cell-wall fragments. Finally, the lysozyme inhibitory effect on a bacterial culture is optionally proposed as a simple microbiological assay. The computer lab exercises described here give students a realistic understanding of the disruptive effect of lysozymes on the bacterial cell wall, a crucial component in bacterial survival. © 2017 by The International Union of Biochemistry and Molecular Biology, 46(1):83-90, 2018. © 2017 The International Union of Biochemistry and Molecular Biology.

ANALOG I/O MODULE TEST SYSTEM BASED ON EPICS CA PROTOCOL AND ACTIVEX CA INTERFACE

DOE Office of Scientific and Technical Information (OSTI.GOV)

YENG,YHOFF,L.

2003-10-13

Analog input (ADC) and output (DAC) modules play a substantial role in device level control of accelerator and large experiment physics control system. In order to get the best performance some features of analog modules including linearity, accuracy, crosstalk, thermal drift and so on have to be evaluated during the preliminary design phase. Gain and offset error calibration and thermal drift compensation (if needed) may have to be done in the implementation phase as well. A natural technique for performing these tasks is to interface the analog VO modules and GPIB interface programmable test instruments with a computer, which canmore » complete measurements or calibration automatically. A difficulty is that drivers of analog modules and test instruments usually work on totally different platforms (vxworks VS Windows). Developing new test routines and drivers for testing instruments under VxWorks (or any other RTOS) platform is not a good solution because such systems have relatively poor user interface and developing such software requires substantial effort. EPICS CA protocol and ActiveX CA interface provide another choice, a PC and LabVIEW based test system. Analog 110 module can be interfaced from LabVIEW test routines via ActiveX CA interface. Test instruments can be controlled via LabVIEW drivers, most of which are provided by instrument vendors or by National Instruments. Labview also provides extensive data analysis and process functions. Using these functions, users can generate powerful test routines very easily. Several applications built for Spallation Neutron Source (SNS) Beam Loss Monitor (BLM) system are described in this paper.« less

Quality Matters! Differences between Expressive and Receptive Non-Verbal Communication Skills in Adolescents with ASD

ERIC Educational Resources Information Center

Grossman, Ruth B.; Tager-Flusberg, Helen

2012-01-01

We analyzed several studies of non-verbal communication (prosody and facial expressions) completed in our lab and conducted a secondary analysis to compare performance on receptive vs. expressive tasks by adolescents with ASD and their typically developing peers. Results show a significant between-group difference for the aggregate score of…

Perceptions of Critical Thinking, Task Value, Autonomy and Science Lab Self-Efficacy: A Longitudinal Examination of Students' CASE Experience

ERIC Educational Resources Information Center

Velez, Jonathan J.; Lambert, Misty D.; Elliott, Kristopher M.

2015-01-01

The purpose of this study was to begin examining the impact of the Curriculum for Agricultural Science Education (CASE). Under development since 2008, the curriculum is intended to integrate core academics and Science, Technology, Engineering, and Math (STEM) into agricultural education programs. This longitudinal descriptive correlational study…

Group Selection and Learning for a Lab-Based Construction Management Course

ERIC Educational Resources Information Center

Solanki, Pranshoo; Kothari, Nidhi

2014-01-01

In construction industries' projects, working in groups is a normal practice. Group work in a classroom is defined as students working collaboratively in a group so that everyone can participate on a collective task. The results from literature review indicate that group work is more effective method of learning as compared to individual work.…

Scientific Writing: Strategies and Tools for Students and Advisors

ERIC Educational Resources Information Center

Singh, Vikash; Mayer, Philipp

2014-01-01

Scientific writing is a demanding task and many students need more time than expected to finish their research articles. To speed up the process, we highlight some tools, strategies as well as writing guides. We recommend starting early in the research process with writing and to prepare research articles, not after but in parallel to the lab or…

A Wet-Lab Approach to Stereochemistry Using [superscript 31]P NMR Spectroscopy

ERIC Educational Resources Information Center

Fenton, Owen S.; Sculimbrene, Bianca R.

2011-01-01

Understanding stereochemistry is an important and difficult task for students to master in organic chemistry. In both introductory and advanced courses, students are encouraged to explore the spatial relationships between molecules, but this exploration is often limited either to the lecture hall or the confines of the library. As such, we sought…

A Methodology to Assess the Benefit of Operational or Tactic Adjustments to Reduce Marine Corps Fuel Consumption

DTIC Science & Technology

2015-12-01

simulation M777A2 howitzer MAGTF Marine Air-Ground Task Force MANA Map Aware Non-Uniform Automata MCWL Marine Corps Warfighting Lab MEB Marine...met. The project developed a Map Aware Non-Uniform Automata (MANA) model for each SPMAGTF size. The MANA models simulated the maneuver and direct

Modeling Hidden Circuits: An Authentic Research Experience in One Lab Period

ERIC Educational Resources Information Center

Moore, J. Christopher; Rubbo, Louis J.

2016-01-01

Two wires exit a black box that has three exposed light bulbs connected together in an unknown configuration. The task for students is to determine the circuit configuration without opening the box. In the activity described in this paper, we navigate students through the process of making models, developing and conducting experiments that can…

A Mini-Library of Sequenced Human DNA Fragments: Linking Bench Experiments with Informatics

ERIC Educational Resources Information Center

Dalgleish, Raymond; Shanks, Morag E.; Monger, Karen; Butler, Nicola J.

2012-01-01

We describe the development of a mini-library of human DNA fragments for use in an enquiry-based learning (EBL) undergraduate practical incorporating "wet-lab" and bioinformatics tasks. In spite of the widespread emergence of the polymerase chain reaction (PCR), the cloning and analysis of DNA fragments in "Escherichia coli"…

Cognitive Computer Tools in the Teaching and Learning of Undergraduate Calculus

ERIC Educational Resources Information Center

Borchelt, Nathan

2007-01-01

The purpose of this study was to explore the use of a cognitive computer tool by undergraduate calculus students as they worked cooperatively on mathematical tasks. Specific attention was given to levels of cognitive demand in which the students were engaged as they completed in-class labs with the assistance of MathCAD. Participants were assigned…

Teaching Business Statistics in a Computer Lab: Benefit or Distraction?

ERIC Educational Resources Information Center

Martin, Linda R.

2011-01-01

Teaching in a classroom configured with computers has been heralded as an aid to learning. Students receive the benefits of working with large data sets and real-world problems. However, with the advent of network and wireless connections, students can now use the computer for alternating tasks, such as emailing, web browsing, and social…

Validity of Selected Lab and Field Tests of Physical Working Capacity.

ERIC Educational Resources Information Center

Burke, Edmund J.

The validity of selected lab and field tests of physical working capacity was investigated. Forty-four male college students were administered a series of lab and field tests of physical working capacity. Lab tests include a test of maximum oxygen uptake, the PWC 170 test, the Harvard Step Test, the Progressive Pulse Ratio Test, Margaria Test of…

Large-scale laboratory testing of bedload-monitoring technologies: overview of the StreamLab06 Experiments

USGS Publications Warehouse

Marr, Jeffrey D.G.; Gray, John R.; Davis, Broderick E.; Ellis, Chris; Johnson, Sara; Gray, John R.; Laronne, Jonathan B.; Marr, Jeffrey D.G.

2010-01-01

A 3-month-long, large-scale flume experiment involving research and testing of selected conventional and surrogate bedload-monitoring technologies was conducted in the Main Channel at the St. Anthony Falls Laboratory under the auspices of the National Center for Earth-surface Dynamics. These experiments, dubbed StreamLab06, involved 25 researchers and volunteers from academia, government, and the private sector. The research channel was equipped with a sediment-recirculation system and a sediment-flux monitoring system that allowed continuous measurement of sediment flux in the flume and provided a data set by which samplers were evaluated. Selected bedload-measurement technologies were tested under a range of flow and sediment-transport conditions. The experiment was conducted in two phases. The bed material in phase I was well-sorted siliceous sand (0.6-1.8 mm median diameter). A gravel mixture (1-32 mm median diameter) composed the bed material in phase II. Four conventional bedload samplers – a standard Helley-Smith, Elwha, BLH-84, and Toutle River II (TR-2) sampler – were manually deployed as part of both experiment phases. Bedload traps were deployed in study Phase II. Two surrogate bedload samplers – stationarymounted down-looking 600 kHz and 1200 kHz acoustic Doppler current profilers – were deployed in experiment phase II. This paper presents an overview of the experiment including the specific data-collection technologies used and the ambient hydraulic, sediment-transport and environmental conditions measured as part of the experiment. All data collected as part of the StreamLab06 experiments are, or will be available to the research community.

The Establishment of a New Friction Stir Welding Process Development Facility at NASA/MSFC

NASA Technical Reports Server (NTRS)

Vaughn, Timothy P.

2012-01-01

The primary objective of full scale development is to mitigate scale-up issues before the vehicle ever reaches production and verify assembly design models. Only at full scale can the true challenges associated with production be identified and dealt with. Also, only at full scale can the delta shift between lab and subscale hardware manufacture and assembly be assessed.

A graphical workstation based part-task flight simulator for preliminary rapid evaluation of advanced displays

NASA Technical Reports Server (NTRS)

Wanke, Craig; Kuchar, James; Hahn, Edward; Pritchett, A.; Hansman, R. John

1994-01-01

Advances in avionics and display technology are significantly changing the cockpit environment in current transport aircraft. The MIT Aeronautical Systems Lab (ASL) developed a part-task flight simulator specifically to study the effects of these new technologies on flight crew situational awareness and performance. The simulator is based on a commercially-available graphics workstation, and can be rapidly reconfigured to meet the varying demands of experimental studies. The simulator was successfully used to evaluate graphical microbursts alerting displays, electronic instrument approach plates, terrain awareness and alerting displays, and ATC routing amendment delivery through digital datalinks.

Beyond Behavioral Inhibition: A Computer Avatar Task Designed to Assess Behavioral Inhibition Extends to Harm Avoidance.

PubMed

Allen, Michael Todd; Jameson, Molly M; Myers, Catherine E

2017-01-01

Personality factors such as behavioral inhibition (BI), a temperamental tendency for avoidance in the face of unfamiliar situations, have been identified as risk factors for anxiety disorders. Personality factors are generally identified through self-report inventories. However, this tendency to avoid may affect the accuracy of these self-report inventories. Previously, a computer based task was developed in which the participant guides an on-screen "avatar" through a series of onscreen events; performance on the task could accurately predict participants' BI, measured by a standard paper and pencil questionnaire (Adult Measure of Behavioral Inhibition, or AMBI). Here, we sought to replicate this finding as well as compare performance on the avatar task to another measure related to BI, the harm avoidance (HA) scale of the Tridimensional Personality Questionnaire (TPQ). The TPQ includes HA scales as well as scales assessing reward dependence (RD), novelty seeking (NS) and persistence. One hundred and one undergraduates voluntarily completed the avatar task and the paper and pencil inventories in a counter-balanced order. Scores on the avatar task were strongly correlated with BI assessed via the AMBI questionnaire, which replicates prior findings. Females exhibited higher HA scores than males, but did not differ on scores on the avatar task. There was a strong positive relationship between scores on the avatar task and HA scores. One aspect of HA, fear of uncertainty was found to moderately mediate the relationship between AMBI scores and avatar scores. NS had a strong negative relationship with scores on the avatar task, but there was no significant relationship between RD and scores on the avatar task. These findings indicate the effectiveness of the avatar task as a behavioral alternative to self-report measures to assess avoidance. In addition, the use of computer based behavioral tasks are a viable alternative to paper and pencil self-report inventories, particularly when assessing anxiety and avoidance.

The c4h, tat, hppr and hppd Genes Prompted Engineering of Rosmarinic Acid Biosynthetic Pathway in Salvia miltiorrhiza Hairy Root Cultures

PubMed Central

Gao, Shouhong; Saechao, Saengking; Di, Peng; Chen, Junfeng; Chen, Wansheng

2011-01-01

Rational engineering to produce biologically active plant compounds has been greatly impeded by our poor understanding of the regulatory and metabolic pathways underlying the biosynthesis of these compounds. Here we capitalized on our previously described gene-to-metabolite network in order to engineer rosmarinic acid (RA) biosynthesis pathway for the production of beneficial RA and lithospermic acid B (LAB) in Salvia miltiorrhiza hairy root cultures. Results showed their production was greatly elevated by (1) overexpression of single gene, including cinnamic acid 4-hydroxylase (c4h), tyrosine aminotransferase (tat), and 4-hydroxyphenylpyruvate reductase (hppr), (2) overexpression of both tat and hppr, and (3) suppression of 4-hydroxyphenylpyruvate dioxygenase (hppd). Co-expression of tat/hppr produced the most abundant RA (906 mg/liter) and LAB (992 mg/liter), which were 4.3 and 3.2-fold more than in their wild-type (wt) counterparts respectively. And the value of RA concentration was also higher than that reported before, that produced by means of nutrient medium optimization or elicitor treatment. It is the first report of boosting RA and LAB biosynthesis through genetic manipulation, providing an effective approach for their large-scale commercial production by using hairy root culture systems as bioreactors. PMID:22242141

Data-Oriented Astrophysics at NOAO: The Science Archive & The Data Lab

NASA Astrophysics Data System (ADS)

Juneau, Stephanie; NOAO Data Lab, NOAO Science Archive

2018-06-01

As we keep progressing into an era of increasingly large astronomy datasets, NOAO’s data-oriented mission is growing in prominence. The NOAO Science Archive, which captures and processes the pixel data from mountaintops in Chile and Arizona, now contains holdings at Petabyte scales. Working at the intersection of astronomy and data science, the main goal of the NOAO Data Lab is to provide users with a suite of tools to work close to this data, the catalogs derived from them, as well as externally provided datasets, and thus optimize the scientific productivity of the astronomy community. These tools and services include databases, query tools, virtual storage space, workflows through our Jupyter Notebook server, and scripted analysis. We currently host datasets from NOAO facilities such as the Dark Energy Survey (DES), the DESI imaging Legacy Surveys (LS), the Dark Energy Camera Plane Survey (DECaPS), and the nearly all-sky NOAO Source Catalog (NSC). We are further preparing for large spectroscopy datasets such as DESI. After a brief overview of the Science Archive, the Data Lab and datasets, I will briefly showcase scientific applications showing use of our data holdings. Lastly, I will describe our vision for future developments as we tackle the next technical and scientific challenges.

Hypnotic suggestibility, cognitive inhibition, and dissociation.

PubMed

Dienes, Zoltán; Brown, Elizabeth; Hutton, Sam; Kirsch, Irving; Mazzoni, Giuliana; Wright, Daniel B

2009-12-01

We examined two potential correlates of hypnotic suggestibility: dissociation and cognitive inhibition. Dissociation is the foundation of two of the major theories of hypnosis and other theories commonly postulate that hypnotic responding is a result of attentional abilities (including inhibition). Participants were administered the Waterloo-Stanford Group Scale of Hypnotic Susceptibility, Form C. Under the guise of an unrelated study, 180 of these participants also completed: a version of the Dissociative Experiences Scale that is normally distributed in non-clinical populations; a latent inhibition task, a spatial negative priming task, and a memory task designed to measure negative priming. The data ruled out even moderate correlations between hypnotic suggestibility and all the measures of dissociation and cognitive inhibition overall, though they also indicated gender differences. The results are a challenge for existing theories of hypnosis.

The Immersive Virtual Reality Lab: Possibilities for Remote Experimental Manipulations of Autonomic Activity on a Large Scale.

PubMed

Juvrud, Joshua; Gredebäck, Gustaf; Åhs, Fredrik; Lerin, Nils; Nyström, Pär; Kastrati, Granit; Rosén, Jörgen

2018-01-01

There is a need for large-scale remote data collection in a controlled environment, and the in-home availability of virtual reality (VR) and the commercial availability of eye tracking for VR present unique and exciting opportunities for researchers. We propose and provide a proof-of-concept assessment of a robust system for large-scale in-home testing using consumer products that combines psychophysiological measures and VR, here referred to as a Virtual Lab. For the first time, this method is validated by correlating autonomic responses, skin conductance response (SCR), and pupillary dilation, in response to a spider, a beetle, and a ball using commercially available VR. Participants demonstrated greater SCR and pupillary responses to the spider, and the effect was dependent on the proximity of the stimuli to the participant, with a stronger response when the spider was close to the virtual self. We replicated these effects across two experiments and in separate physical room contexts to mimic variability in home environment. Together, these findings demonstrate the utility of pupil dilation as a marker of autonomic arousal and the feasibility to assess this in commercially available VR hardware and support a robust Virtual Lab tool for massive remote testing.

A Miniaturized Extruder to Prototype Amorphous Solid Dispersions: Selection of Plasticizers for Hot Melt Extrusion.

PubMed

Lauer, Matthias E; Maurer, Reto; Paepe, Anne T De; Stillhart, Cordula; Jacob, Laurence; James, Rajesh; Kojima, Yuki; Rietmann, Rene; Kissling, Tom; van den Ende, Joost A; Schwarz, Sabine; Grassmann, Olaf; Page, Susanne

2018-05-19

Hot-melt extrusion is an option to fabricate amorphous solid dispersions and to enhance oral bioavailability of poorly soluble compounds. The selection of suitable polymer carriers and processing aids determines the dissolution, homogeneity and stability performance of this solid dosage form. A miniaturized extrusion device (MinEx) was developed and Hypromellose acetate succinate type L (HPMCAS-L) based extrudates containing the model drugs neurokinin-1 (NK1) and cholesterylester transfer protein (CETP) were manufactured, plasticizers were added and their impact on dissolution and solid-state properties were assessed. Similar mixtures were manufactured with a lab-scale extruder, for face to face comparison. The properties of MinEx extrudates widely translated to those manufactured with a lab-scale extruder. Plasticizers, Polyethyleneglycol 4000 (PEG4000) and Poloxamer 188, were homogenously distributed but decreased the storage stability of the extrudates. Stearic acid was found condensed in ultrathin nanoplatelets which did not impact the storage stability of the system. Depending on their distribution and physicochemical properties, plasticizers can modulate storage stability and dissolution performance of extrudates. MinEx is a valuable prototyping-screening method and enables rational selection of plasticizers in a time and material sparing manner. In eight out of eight cases the properties of the extrudates translated to products manufactured in lab-scale extrusion trials.

The Immersive Virtual Reality Lab: Possibilities for Remote Experimental Manipulations of Autonomic Activity on a Large Scale

PubMed Central

Juvrud, Joshua; Gredebäck, Gustaf; Åhs, Fredrik; Lerin, Nils; Nyström, Pär; Kastrati, Granit; Rosén, Jörgen

2018-01-01

There is a need for large-scale remote data collection in a controlled environment, and the in-home availability of virtual reality (VR) and the commercial availability of eye tracking for VR present unique and exciting opportunities for researchers. We propose and provide a proof-of-concept assessment of a robust system for large-scale in-home testing using consumer products that combines psychophysiological measures and VR, here referred to as a Virtual Lab. For the first time, this method is validated by correlating autonomic responses, skin conductance response (SCR), and pupillary dilation, in response to a spider, a beetle, and a ball using commercially available VR. Participants demonstrated greater SCR and pupillary responses to the spider, and the effect was dependent on the proximity of the stimuli to the participant, with a stronger response when the spider was close to the virtual self. We replicated these effects across two experiments and in separate physical room contexts to mimic variability in home environment. Together, these findings demonstrate the utility of pupil dilation as a marker of autonomic arousal and the feasibility to assess this in commercially available VR hardware and support a robust Virtual Lab tool for massive remote testing. PMID:29867318

SMR Re-Scaling and Modeling for Load Following Studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoover, K.; Wu, Q.; Bragg-Sitton, S.

2016-11-01

This study investigates the creation of a new set of scaling parameters for the Oregon State University Multi-Application Small Light Water Reactor (MASLWR) scaled thermal hydraulic test facility. As part of a study being undertaken by Idaho National Lab involving nuclear reactor load following characteristics, full power operations need to be simulated, and therefore properly scaled. Presented here is the scaling analysis and plans for RELAP5-3D simulation.

Arousability and Fall Risk During Forced Awakenings From Nocturnal Sleep Among Healthy Males Following Administration of Zolpidem 10 mg and Doxepin 6 mg: A Randomized, Placebo-Controlled, Four-Way Crossover Trial.

PubMed

Drake, Christopher L; Durrence, Heith; Cheng, Philip; Roth, Thomas; Pillai, Vivek; Peterson, Edward L; Singh, Meeta; Tran, Kieulinh Michelle

2017-07-01

To examine and compare the arousability threshold and fall risk upon awakening of doxepin (6 mg) versus zolpidem (10 mg). A total of 52 healthy adult males were included in a double-blind, placebo-controlled, four-way crossover study. The experimental procedure included four nights with polysomnography in the lab (zolpidem, doxepin, and their respective placebo conditions). Arousability was measured using an auditory awakening threshold delivered at the peak-plasma concentration for the active hypnotics and at matched times for the respective placebo conditions. Fall risk during the night was measured following awakening using the Berg Balance Scale and the Tandem Walk Task. Both arousability and fall risk were lower in the doxepin condition compared to the zolpidem condition. Furthermore, arousability and fall risk for doxepin did not differ significantly from the placebo conditions. A significantly greater proportion of participants in the zolpidem condition (63.5%) did not wake until receiving the loudest tone (110 dB) as compared to the doxepin (17.6%) and placebo conditions (17.3%, 5.8%). Results suggest that zolpidem has greater risks for balance and awakening threshold compared with low-dose doxepin. Future prospective studies should extend results to clinical samples with population-level risk of injury and arousability. © Sleep Research Society 2017. Published by Oxford University Press on behalf of the Sleep Research Society. All rights reserved. For permissions, please e-mail journals.permissions@oup.com.

Skin elasticity as a measure of radiation fibrosis: is it reproducible and does it correlate with patient and physician-reported measures?

PubMed

Nguyen, Nhu-Tram A; Roberge, David; Freeman, Carolyn R; Wong, Cindy; Hines, Jerod; Turcotte, Robert E

2014-10-01

Current means of measuring RT-induced fibrosis are subjective. We evaluated the DermaLab suction cup system to measure objectively skin deflection as a surrogate for fibrosis. Sixty-nine patients with E-STS were treated with limb-sparing surgery and 50-66 Grays (Gy) of RT. Using a "scleroderma" DermaLab Suction Cup, the skin stiffness was measured by two clinicians. The National Cancer Institute Common Terminology Criteria for Adverse Events (NCI-CTCAE) scale, the Musculoskeletal Tumor Rating Scale (MSTS) and Toronto Extremity Salvage Score (TESS) questionnaires were completed for each patient. Levels of agreement between measurers were estimated using the Kappa (k) coefficient and the concordance correlation coefficient (CCC). All sixty-nine patients were included. The level of agreement between measurers for NCI-CTCAE grading was moderate (range k = 0.41-0.59). The CCC for the elasticity measurements were higher, with CCC = 0.82 for fibrotic skin and CCC 5 0.84 for normal skin. The elasticity measurements were significantly higher when MSTS scores were <30 and or TESS scores were <90. Suction Cup measurement of skin elasticity is more reproducible than CTCAE grading and shows promise in generating reproducible measurements for radiation-induced skin fibrosis. Furthermore, it correlates well with the MSTS and TESS.

Fuel-Flexible Gasification-Combustion Technology for Production of H2 and Sequestration-Ready CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Raul Subia

GE Global Research is developing an innovative energy technology for coal gasification with high efficiency and near-zero pollution. This Unmixed Fuel Processor (UFP) technology simultaneously converts coal, steam and air into three separate streams of hydrogen-rich gas, sequestration-ready CO{sub 2}, and high-temperature, high-pressure vitiated air to produce electricity in gas turbines. This is the draft final report for the first stage of the DOE-funded Vision 21 program. The UFP technology development program encompassed lab-, bench- and pilot-scale studies to demonstrate the UFP concept. Modeling and economic assessments were also key parts of this program. The chemical and mechanical feasibility weremore » established via lab and bench-scale testing, and a pilot plant was designed, constructed and operated, demonstrating the major UFP features. Experimental and preliminary modeling results showed that 80% H{sub 2} purity could be achieved, and that a UFP-based energy plant is projected to meet DOE efficiency targets. Future work will include additional pilot plant testing to optimize performance and reduce environmental, operability and combined cycle integration risks. Results obtained to date have confirmed that this technology has the potential to economically meet future efficiency and environmental performance goals.« less

Scale-up of the electrokinetic fence technology for the removal of pesticides. Part II: Does size matter for removal of herbicides?

PubMed

López-Vizcaíno, R; Risco, C; Isidro, J; Rodrigo, S; Saez, C; Cañizares, P; Navarro, V; Rodrigo, M A

2017-01-01

This work reports results of the application of electrokinetic fence technology in a 32 m 3 -prototype which contains soil polluted with 2,4-D and oxyfluorfen, focusing on the evaluation of the mechanisms that describe the removal of these two herbicides and comparing results to those obtained in smaller plants: a pilot-scale mockup (175 L) and a lab-scale soil column (1 L). Results show that electric heating of soil (coupled with the increase in the volatility) is the key to explain the removal of pollutants in the largest scale facility while electrokinetic transport processes are the primary mechanisms that explain the removal of herbicides in the lab-scale plant. 2-D and 3-D maps of the temperature and pollutant concentrations are used in the discussion of results trying to give light about the mechanisms and about how the size of the setup can lead to different conclusions, despite the same processes are occurring in the soil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Deriving Childhood Temperament Measures from Emotion-eliciting Behavioral Episodes: Scale Construction and Initial Validation

PubMed Central

Gagne, Jeffrey R.; Van Hulle, Carol A.; Aksan, Nazan; Essex, Marilyn J.; Goldsmith, H. Hill

2010-01-01

The authors describe the development and initial validation of a home-based version of the Laboratory Temperament Assessment Battery (Lab-TAB), which was designed to assess childhood temperament using a comprehensive series of emotion-eliciting behavioral episodes. This paper provides researchers with general guidelines for assessing specific behaviors using the Lab-TAB and for forming behavioral composites that correspond to commonly researched temperament dimensions. We used mother ratings and independent post-visit observer ratings to provide validity evidence in a community sample of 4.5 year-old children. 12 Lab-TAB behavioral episodes were employed, yielding 24 within-episode temperament components that collapsed into 9 higher-level composites (Anger, Sadness, Fear, Shyness, Positive Expression, Approach, Active Engagement, Persistence, and Inhibitory Control). These dimensions of temperament are similar to those found in questionnaire-based assessments. Correlations among the 9 composites were low to moderate, suggesting relative independence. As expected, agreement between Lab-TAB measures and post-visit observer ratings was stronger than agreement between the Lab-TAB and mother questionnaire. However, for Active Engagement and Shyness, mother ratings did predict child behavior in the Lab-TAB quite well. Findings demonstrate the feasibility of emotion-eliciting temperament assessment methodologies, suggest appropriate methods for data aggregation into trait-level constructs, and set some expectations for associations between Lab-TAB dimensions and the degree of cross-method convergence between the Lab-TAB and other commonly used temperament assessments. PMID:21480723

Embedding Task-Based Neural Models into a Connectome-Based Model of the Cerebral Cortex.

PubMed

Ulloa, Antonio; Horwitz, Barry

2016-01-01

A number of recent efforts have used large-scale, biologically realistic, neural models to help understand the neural basis for the patterns of activity observed in both resting state and task-related functional neural imaging data. An example of the former is The Virtual Brain (TVB) software platform, which allows one to apply large-scale neural modeling in a whole brain framework. TVB provides a set of structural connectomes of the human cerebral cortex, a collection of neural processing units for each connectome node, and various forward models that can convert simulated neural activity into a variety of functional brain imaging signals. In this paper, we demonstrate how to embed a previously or newly constructed task-based large-scale neural model into the TVB platform. We tested our method on a previously constructed large-scale neural model (LSNM) of visual object processing that consisted of interconnected neural populations that represent, primary and secondary visual, inferotemporal, and prefrontal cortex. Some neural elements in the original model were "non-task-specific" (NS) neurons that served as noise generators to "task-specific" neurons that processed shapes during a delayed match-to-sample (DMS) task. We replaced the NS neurons with an anatomical TVB connectome model of the cerebral cortex comprising 998 regions of interest interconnected by white matter fiber tract weights. We embedded our LSNM of visual object processing into corresponding nodes within the TVB connectome. Reciprocal connections between TVB nodes and our task-based modules were included in this framework. We ran visual object processing simulations and showed that the TVB simulator successfully replaced the noise generation originally provided by NS neurons; i.e., the DMS tasks performed with the hybrid LSNM/TVB simulator generated equivalent neural and fMRI activity to that of the original task-based models. Additionally, we found partial agreement between the functional connectivities using the hybrid LSNM/TVB model and the original LSNM. Our framework thus presents a way to embed task-based neural models into the TVB platform, enabling a better comparison between empirical and computational data, which in turn can lead to a better understanding of how interacting neural populations give rise to human cognitive behaviors.

Development and modelling of a steel slag filter effluent neutralization process with CO2-enriched air from an upstream bioprocess.

PubMed

Bove, Patricia; Claveau-Mallet, Dominique; Boutet, Étienne; Lida, Félix; Comeau, Yves

2018-02-01

The main objective of this project was to develop a steel slag filter effluent neutralization process by acidification with CO 2 -enriched air coming from a bioprocess. Sub-objectives were to evaluate the neutralization capacity of different configurations of neutralization units in lab-scale conditions and to propose a design model of steel slag effluent neutralization. Two lab-scale column neutralization units fed with two different types of influent were operated at hydraulic retention time of 10 h. Tested variables were mode of flow (saturated or percolating), type of media (none, gravel, Bionest and AnoxKaldnes K3), type of air (ambient or CO 2 -enriched) and airflow rate. One neutralization field test (saturated and no media, 2000-5000 ppm CO 2 , sequential feeding, hydraulic retention time of 7.8 h) was conducted for 7 days. Lab-scale and field-scale tests resulted in effluent pH of 7.5-9.5 when the aeration rate was sufficiently high. A model was implemented in the PHREEQC software and was based on the carbonate system, CO 2 transfer and calcite precipitation; and was calibrated on ambient air lab tests. The model was validated with CO 2 -enriched air lab and field tests, providing satisfactory validation results over a wide range of CO 2 concentrations. The flow mode had a major impact on CO 2 transfer and hydraulic efficiency, while the type of media had little influence. The flow mode also had a major impact on the calcite surface concentration in the reactor: it was constant in saturated mode and was increasing in percolating mode. Predictions could be made for different steel slag effluent pH and different operation conditions (hydraulic retention time, CO 2 concentration, media and mode of flow). The pH of the steel slag filter effluent and the CO 2 concentration of the enriched air were factors that influenced most the effluent pH of the neutralization process. An increased concentration in CO 2 in the enriched air reduced calcite precipitation and clogging risks. Stoichiometric calculations showed that a typical domestic septic tank effluent with 300 mg/L of biodegradable COD provides enough biological CO 2 for neutralization of a steel slag effluent with pH of 10.5-11.5. A saturated neutralization reactor with no media operated at hydraulic retention time of 10 h and a concentration of 2000 ppm in CO 2 enriched air is recommended for full-scale applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Solar photocatalitycal treatment of carbofuran at lab and pilot scale: effect of classical parameters, evaluation of the toxicity and analysis of organic by-products.

PubMed

Lopez-Alvarez, Blady; Torres-Palma, Ricardo A; Peñuela, Gustavo

2011-07-15

In this work the TiO(2) solar-photocatalytical degradation of the pesticide carbofuran (CBF) in water, at lab and pilot scale, was studied. At lab scale the evaluation of CBF concentration (14-282 μmol L(-1)) showed that the system followed a Langmuir-Hinshelwood kinetics type. TiO(2) concentration (0.05-2 g L(-1)) and initial pH (3-9) were also evaluated and optimized using the surface response methodology and the Pareto diagram. In the range of variables studied, initial pH 7.60 and 1.43 g L(-1) of TiO(2) favoured the efficiency of the process. Under optimal conditions the evolution of substrate, chemical oxygen demand, dissolved organic carbon, toxicity and organics by-products were evaluated. In the pilot scale tests, using direct sunlight, 55 mg L(-1) of CBF in a commercial formulation was eliminated after 420 min; while after 900 min of treatment 80% of toxicity (1/E(50) on Vibrium Fischeri), 80% of chemical oxygen demand and 60% of dissolved organic carbon were removed. The analysis and evolution of five CBF by-products, as well the evaluation of the treatment in the presence of isopropanol or using acetonitrile as a solvent suggest that the degradation is mainly carried out by OH radical attack. Finally, a schema depicting the main degradation pathway is proposed. Copyright © 2011 Elsevier B.V. All rights reserved.

Caring more and knowing more reduces age-related differences in emotion perception.

PubMed

Stanley, Jennifer Tehan; Isaacowitz, Derek M

2015-06-01

Traditional emotion perception tasks show that older adults are less accurate than are young adults at recognizing facial expressions of emotion. Recently, we proposed that socioemotional factors might explain why older adults seem impaired in lab tasks but less so in everyday life (Isaacowitz & Stanley, 2011). Thus, in the present research we empirically tested whether socioemotional factors such as motivation and familiarity can alter this pattern of age effects. In 1 task, accountability instructions eliminated age differences in the traditional emotion perception task. Using a novel emotion perception paradigm featuring spontaneous dynamic facial expressions of a familiar romantic partner versus a same-age stranger, we found that age differences in emotion perception accuracy were attenuated in the familiar partner condition, relative to the stranger condition. Taken together, the results suggest that both overall accuracy as well as specific patterns of age effects differ appreciably between traditional emotion perception tasks and emotion perception within a socioemotional context. (c) 2015 APA, all rights reserved.

Caring More and Knowing More Reduces Age-Related Differences in Emotion Perception

PubMed Central

Stanley, Jennifer Tehan; Isaacowitz, Derek M.

2015-01-01

Traditional emotion perception tasks show that older adults are less accurate than young adults at recognizing facial expressions of emotion. Recently, we proposed that socioemotional factors might explain why older adults seem impaired in lab tasks but less so in everyday life (Isaacowitz & Stanley, 2011). Thus, in the present research we empirically tested whether socioemotional factors such as motivation and familiarity can alter this pattern of age effects. In one task, accountability instructions eliminated age differences in the traditional emotion perception task. Using a novel emotion perception paradigm featuring spontaneous dynamic facial expressions of a familiar romantic partner versus a same-age stranger, we found that age differences in emotion perception accuracy were attenuated in the familiar partner condition, relative to the stranger condition. Taken together, the results suggest that both overall accuracy as well as specific patterns of age effects differ appreciably between traditional emotion perception tasks and emotion perception within a socioemotional context. PMID:26030775

Metabolic Engineering toward Sustainable Production of Nylon-6.

PubMed

Turk, Stefan C H J; Kloosterman, Wigard P; Ninaber, Dennis K; Kolen, Karin P A M; Knutova, Julia; Suir, Erwin; Schürmann, Martin; Raemakers-Franken, Petronella C; Müller, Monika; de Wildeman, Stefaan M A; Raamsdonk, Leonie M; van der Pol, Ruud; Wu, Liang; Temudo, Margarida F; van der Hoeven, Rob A M; Akeroyd, Michiel; van der Stoel, Roland E; Noorman, Henk J; Bovenberg, Roel A L; Trefzer, Axel C

2016-01-15

Nylon-6 is a bulk polymer used for many applications. It consists of the non-natural building block 6-aminocaproic acid, the linear form of caprolactam. Via a retro-synthetic approach, two synthetic pathways were identified for the fermentative production of 6-aminocaproic acid. Both pathways require yet unreported novel biocatalytic steps. We demonstrated proof of these bioconversions by in vitro enzyme assays with a set of selected candidate proteins expressed in Escherichia coli. One of the biosynthetic pathways starts with 2-oxoglutarate and contains bioconversions of the ketoacid elongation pathway known from methanogenic archaea. This pathway was selected for implementation in E. coli and yielded 6-aminocaproic acid at levels up to 160 mg/L in lab-scale batch fermentations. The total amount of 6-aminocaproic acid and related intermediates generated by this pathway exceeded 2 g/L in lab-scale fed-batch fermentations, indicating its potential for further optimization toward large-scale sustainable production of nylon-6.

The Effects of Virtual Versus Physical Lab Manipulatives on Inquiry Skill Acquisition and Conceptual Understanding of Density

NASA Astrophysics Data System (ADS)

Brinson, James R.

The current study compared the effects of virtual versus physical laboratory manipulatives on 84 undergraduate non-science majors' (a) conceptual understanding of density and (b) density-related inquiry skill acquisition. A pre-post comparison study design was used, which incorporated all components of an inquiry-guided classroom, except experimental mode, and which controlled for curriculum, instructor, instructional method, time spent on task, and availability of reference resources. Participants were randomly assigned to either a physical or virtual lab group. Pre- and post-assessments of conceptual understanding and inquiry skills were administered to both groups. Paired-samples t tests revealed a significant mean percent correct score increase for conceptual understanding in both the physical lab group (M = .103, SD = .168), t(38) = -3.82, p < .001, r = .53, two-tailed, and the virtual lab group (M = .084, SD = .177), t(44) = -3.20, p = .003, r = .43, two-tailed. However, a one-way ANCOVA (using pretest scores as the covariate) revealed that the main effect of lab group on conceptual learning gains was not significant, F(1, 81) = 0.081, p = .776, two-tailed. An omnibus test of model coefficients within hierarchical logistic regression revealed that a correct response on inquiry pretest scores was not a significant predictor of a correct post-test response, chi 2(1, N = 84) = 1.68, p = .195, and that when lab mode was added to the model, it did not significantly increase the model's predictive ability, chi2(2, N = 84) = 1.95, p = .377. Thus, the data in the current study revealed no significant difference in the effect of physical versus virtual manipulatives when used to teach conceptual understanding and inquiry skills related to density.

How Do You Like Your Science, Wet or Dry? How Two Lab Experiences Influence Student Understanding of Science Concepts and Perceptions of Authentic Scientific Practice

PubMed Central

Munn, Maureen; Knuth, Randy; Van Horne, Katie; Shouse, Andrew W.; Levias, Sheldon

2017-01-01

This study examines how two kinds of authentic research experiences related to smoking behavior—genotyping human DNA (wet lab) and using a database to test hypotheses about factors that affect smoking behavior (dry lab)—influence students’ perceptions and understanding of scientific research and related science concepts. The study used pre and post surveys and a focus group protocol to compare students who conducted the research experiences in one of two sequences: genotyping before database and database before genotyping. Students rated the genotyping experiment to be more like real science than the database experiment, in spite of the fact that they associated more scientific tasks with the database experience than genotyping. Independent of the order of completing the labs, students showed gains in their understanding of science concepts after completion of the two experiences. There was little change in students’ attitudes toward science pre to post, as measured by the Scientific Attitude Inventory II. However, on the basis of their responses during focus groups, students developed more sophisticated views about the practices and nature of science after they had completed both research experiences, independent of the order in which they experienced them. PMID:28572181

The Effect of Tool Handle Shape on Hand Muscle Load and Pinch Force in a Simulated Dental Scaling Task

PubMed Central

Dong, Hui; Loomer, Peter; Barr, Alan; LaRoche, Charles; Young, Ed; Rempel, David

2007-01-01

Work-related upper extremity musculoskeletal disorders, including carpal tunnel syndrome, are prevalent among dentists and dental hygienists. An important risk factor for developing these disorders is forceful pinching which occurs during periodontal work such as dental scaling. Ergonomically designed dental scaling instruments may help reduce the prevalence of carpal tunnel syndrome among dental practitioners. In this study, 8 custom-designed dental scaling instruments with different handle shapes were used by 24 dentists and dental hygienists to perform a simulated tooth scaling task. The muscle activity of two extensors and two flexors in the forearm was recorded with electromyography while thumb pinch force was measured by pressure sensors. The results demonstrated that the instrument handle with a tapered, round shape and a 10 mm diameter required the least muscle load and pinch force when performing simulated periodontal work. The results from this study can guide dentists and dental hygienists in selection of dental scaling instruments. PMID:17156742

Automation reliability in unmanned aerial vehicle control: a reliance-compliance model of automation dependence in high workload.

PubMed

Dixon, Stephen R; Wickens, Christopher D

2006-01-01

Two experiments were conducted in which participants navigated a simulated unmanned aerial vehicle (UAV) through a series of mission legs while searching for targets and monitoring system parameters. The goal of the study was to highlight the qualitatively different effects of automation false alarms and misses as they relate to operator compliance and reliance, respectively. Background data suggest that automation false alarms cause reduced compliance, whereas misses cause reduced reliance. In two studies, 32 and 24 participants, including some licensed pilots, performed in-lab UAV simulations that presented the visual world and collected dependent measures. Results indicated that with the low-reliability aids, false alarms correlated with poorer performance in the system failure task, whereas misses correlated with poorer performance in the concurrent tasks. Compliance and reliance do appear to be affected by false alarms and misses, respectively, and are relatively independent of each other. Practical implications are that automated aids must be fairly reliable to provide global benefits and that false alarms and misses have qualitatively different effects on performance.

CONVERTING CAMPUS WASTE STREAMS INTO LOCALLY USED ENERGY PRODUCTS THROUGH STEAM HYDROGASIFICATION AND METHANE REFORMATION

EPA Science Inventory

We expect to find that the application of our technology can significantly benefit the school, environmentally and economically. Our lab-scale demonstration results would lead to larger demonstration scale investigations and ultimately implementation on campus showcasing the p...

Cardiac catheterization laboratory management: the fundamentals.

PubMed

Newell, Amy

2012-01-01

Increasingly, imaging administrators are gaining oversight for the cardiac cath lab as part of imaging services. Significant daily challenges include physician and staff demands, as well as patients who in many cases require higher acuity care. Along with strategic program driven responsibilities, the management role is complex. Critical elements that are the major impacts on cath lab management, as well as the overall success of a cardiac and vascular program, include program quality, patient safety, operational efficiency including inventory management, and customer service. It is critically important to have a well-qualified cath lab manager who acts as a leader by example, a mentor and motivator of the team, and an expert in the organization's processes and procedures. Such qualities will result in a streamlined cath lab with outstanding results.

Inexpensive DAQ based physics labs

NASA Astrophysics Data System (ADS)

Lewis, Benjamin; Clark, Shane

2015-11-01

Quality Data Acquisition (DAQ) based physics labs can be designed using microcontrollers and very low cost sensors with minimal lab equipment. A prototype device with several sensors and documentation for a number of DAQ-based labs is showcased. The device connects to a computer through Bluetooth and uses a simple interface to control the DAQ and display real time graphs, storing the data in .txt and .xls formats. A full device including a larger number of sensors combined with software interface and detailed documentation would provide a high quality physics lab education for minimal cost, for instance in high schools lacking lab equipment or students taking online classes. An entire semester’s lab course could be conducted using a single device with a manufacturing cost of under $20.

Sex differences in negative affect and lapse behavior during acute tobacco abstinence: a laboratory study.

PubMed

Pang, Raina D; Leventhal, Adam M

2013-08-01

Heightened negative affect during acute tobacco abstinence in women relative to men could be an important factor underlying sex differences in smoking motivation. However, little controlled experimental work addresses this hypothesis. The current study investigated sex differences in withdrawal-related negative affect, time to start smoking on a lab analogue smoking lapse task, and the interrelation between sex, withdrawal-related negative affect, and smoking lapse behavior. Following a baseline session, current smokers (women: n = 68, men: n = 131) attended two counterbalanced lab sessions (16 hours smoking abstinence and ad libitum smoking) during which they completed self-report measures of mood and withdrawal symptoms followed by a laboratory analogue smoking lapse task. In this task participants are monetarily rewarded for delaying smoking. Performance on this task serves as an analogue model of smoking lapse behavior by measuring smoker's capability to resist temptation to smoke under conditions where abstinence is advantageous. Females showed greater abstinence induced increases in composite negative affect as well as several particular negative affect states (i.e., POMS Anger, Anxiety, Depression, and Confusion, ps < .05) but no differences in abstinence induced changes in other forms of affect or craving. Females also exhibited marginally greater abstinence induced decreases in their willingness to delay smoking for money (p = .10), which was mediated by abstinence induced increases in anger (p < .05). These results suggest that differential sensitivity to abstinence induced negative affect, particularly anger, could underlie sex specific smoking patterns. Negative affect during tobacco abstinence may be an important factor for understanding and treating nicotine addiction in women. PsycINFO Database Record (c) 2013 APA, all rights reserved

Large Vocabulary Audio-Visual Speech Recognition

DTIC Science & Technology

2002-06-12

www.is.cs.cmu.edu Email: waibel(a)cs.cmu~edu Inttractive Systenms Labs ttoctis Ssstms Labs Meeting Browser - -- Interpreting Human Communication "Why did...Speech Interacti Stams Labs t-cive Systms Focus of Attention Tracking Conclusion - Complete Model of Human Communication is Needed - Include all

Promoting Metacognition in Introductory Calculus-based Physics Labs

NASA Astrophysics Data System (ADS)

Grennell, Drew; Boudreaux, Andrew

2010-10-01

In the Western Washington University physics department, a project is underway to develop research-based laboratory curriculum for the introductory calculus-based course. Instructional goals not only include supporting students' conceptual understanding and reasoning ability, but also providing students with opportunities to engage in metacognition. For the latter, our approach has been to scaffold reflective thinking with guided questions. Specific instructional strategies include analysis of alternate reasoning presented in fictitious dialogues and comparison of students' initial ideas with their lab group's final, consensus understanding. Assessment of student metacognition includes pre- and post- course data from selected questions on the CLASS survey, analysis of written lab worksheets, and student opinion surveys. CLASS results are similar to a traditional physics course and analysis of lab sheets show that students struggle to engage in a metacognitive process. Future directions include video studies, as well as use of additional written assessments adapted from educational psychology.

Use of Psychrotolerant Lactic Acid Bacteria (Lactobacillus spp. and Leuconostoc spp.) Isolated from Chinese Traditional Paocai for the Quality Improvement of Paocai Products.

PubMed

Liu, Aiping; Li, Xiaoyan; Pu, Biao; Ao, Xiaolin; Zhou, Kang; He, Li; Chen, Shujuan; Liu, Shuliang

2017-03-29

To improve the quality of Chinese traditional Paocai, two psychrotolerant lactic acid bacteria (LAB) strains were isolated from Paocai, and the quality of Chinese Paocai product using these two strains as starter cultures was compared to a control sample fermented with aged brine at 10 °C. The results suggested that the physicochemical and sensory features of Paocai fermented with psychrotolerant LAB were more suitable for industrial applications. The nitrite content of Paocai fermented with psychrotolerant LAB was 1 mg/kg, which was significantly lower than that of the control Paocai (P < 0.05). Low-temperature fermentation with the starter cultures of psychrotolerant LAB could effectively prevent overacidity and over-ripening of the Paocai products. Additionally, Paocai fermented with psychrotolerant LAB harbored relatively simple microbial flora as revealed by polymerase chain reaction-denaturing gradient gel electrophoresis. This study provides a basis for improving the quality of Chinese traditional Paocai and the large-scale production of low-temperature Chinese traditional Paocai products.

Development and Initial Validation of the Activity Patterns Scale in Patients With Chronic Pain.

PubMed

Esteve, Rosa; Ramírez-Maestre, Carmen; Peters, Madelon L; Serrano-Ibáñez, Elena R; Ruíz-Párraga, Gema T; López-Martínez, Alicia E

2016-04-01

Several self-report measures were used to identify 6 activity patterns in chronic pain patients: pain avoidance, activity avoidance, task-contingent persistence, excessive persistence, pain-contingent persistence, and pacing. Instruments for assessing pacing should include 3 pacing behaviors (breaking tasks into smaller tasks, taking frequent short rests, slowing down), each of which relate to a single goal (increasing activity levels, conserving energy for valued activities, and reducing pain). This article presents the Activity Patterns Scale (APS), which assesses these 6 activity patterns. Study 1 included 291 participants with chronic pain, and tested 3 structures using confirmatory factor analyses. The structure with the best fit had 8 factors corresponding to the hypothesized scales. High correlations in the expected direction were found between the APS subscales and the "Patterns of Activity Measure-Pain." Study 2 included 111 patients with chronic pain, and aimed at examining the association between the APS subscales and adjustment to pain. It was found that that activity avoidance was associated with daily functioning and impairment. Negative affect was positively associated with activity avoidance and excessive persistence, and negatively associated with task-contingent persistence, which was also positively associated with positive affect. This study showed that the APS is a valid and reliable instrument for clinical practice and research. This article presents a valid and reliable instrument to assess activity patterns in patients with chronic pain. The findings suggest that avoidance, persistence, and pacing are multidimensional constructs. Distinguishing between these dimensions sheds light on previous contradictory results and has direct clinical implications regarding recommending the most advisable activity patterns. Copyright © 2016 American Pain Society. Published by Elsevier Inc. All rights reserved.

Relationships of the Leadership Attitudes and Beliefs Scale with Student Types, Study Habits, Life-Long Learning, and GPA

ERIC Educational Resources Information Center

Wielkiewicz, Richard M.; Prom, Christina L.; Loos, Steven

2005-01-01

The Leadership Attitudes and Beliefs Scale (LABS-III; Wielkiewicz, 2000) was validated against a measure with a more traditional, position-based definition of leadership. Disagreement with Hierarchical Thinking was associated with a higher GPA. A Life-Long Learning scale was strongly associated with GPA, Systemic Thinking, and social activism.…

The economic production of alcohol fuels from coal-derived synthesis gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kugler, E.L.; Dadyburjor, D.B.; Yang, R.Y.K.

1995-12-31

The objectives of this project are to discover, (1) study and evaluate novel heterogeneous catalytic systems for the production of oxygenated fuel enhancers from synthesis gas. Specifically, alternative methods of preparing catalysts are to be investigated, and novel catalysts, including sulfur-tolerant ones, are to be pursued. (Task 1); (2) explore, analytically and on the bench scale, novel reactor and process concepts for use in converting syngas to liquid fuel products. (Task 1); (3) simulate by computer the most energy efficient and economically efficient process for converting coal to energy, with primary focus on converting syngas to fuel alcohols. (Task 2);more » (4) develop on the bench scale the best holistic combination of chemistry, catalyst, reactor and total process configuration integrated with the overall coal conversion process to achieve economic optimization for the conversion of syngas to liquid products within the framework of achieving the maximum cost effective transformation of coal to energy equivalents. (Tasks 1 and 2); and (5) evaluate the combustion, emission and performance characteristics of fuel alcohols and blends of alcohols with petroleum-based fuels. (Task 2)« less

On Laboratory Work

NASA Astrophysics Data System (ADS)

Olney, Dave

1997-11-01

This paper offers some suggestions on making lab work for high school chemistry students more productive, with students taking an active role. They include (1) rewriting labs from manuals to better suit one's purpose, (2) the questionable use of canned data tables, (3) designing microscale labs that utilize its unique features, such as safety and ease of repetition, (4) having students actually carry out experimental design on occasion, using a model from PRACTICE IN THINKING, and (5) using comuters/calculators in the lab in meaningful ways. Many examples feature discovery-type labs the author has developed over the years.

Reactive and regulative temperament in patients with compulsive buying and non-clinical controls measured by self-report and performance-based tasks.

PubMed

Voth, Eva M; Claes, Laurence; Georgiadou, Ekaterini; Selle, Janine; Trotzke, Patrick; Brand, Matthias; de Zwaan, Martina; Müller, Astrid

2014-10-01

To examine reactive and regulative temperament in patients with compulsive buying (CB) by means of self-report measures and performance-based tasks and to explore the relationship between both measurement approaches. The study included 31 treatment-seeking patients with CB (25 women, 6 men) and an age and gender matched non-clinical control group without CB (CG). All participants answered the Compulsive Buying Scale (CBS). Reactive temperament was assessed using the Behavioral Inhibition System/Behavioral Activation System Scales (BIS/BAS) and the Iowa Gambling Task (IGT). Regulative temperament was measured using the Effortful Control subscale of the Adult Temperament Questionnaire (ATQ-EC) and a computerized version of the Stroop Task. To control the results for depression, the Patient Health Questionnaire-Depression Scale (PHQ-9) was administered. Crude group comparisons revealed higher BIS and BAS scores, poorer IGT performance and lower ATQ-EC scores in the CB-group compared to the CG. The groups did not differ in their performance on the Stroop task. After controlling for depressive symptoms that were significantly higher in the CB-group, only the group differences in BAS reactivity remained significant. No significant associations were found between questionnaires and performance-based tasks. Overall, the findings indicate that CB in the present clinical sample of treatment-seeking patients was mainly associated with higher approach tendencies and more depressive symptoms. The lacking correlation between self-reports and performance-based tasks is in line with prior research and suggests that both methodologies tap into different aspects of temperament. Copyright © 2014 Elsevier Inc. All rights reserved.

The Age Prospective Memory Paradox: Young Adults May Not Give Their Best outside of the Lab

ERIC Educational Resources Information Center

Aberle, Ingo; Rendell, Peter G.; Rose, Nathan S.; McDaniel, Mark A.; Kliegel, Matthias

2010-01-01

Previous research has identified the age prospective memory paradox of age-related declines in laboratory settings in contrast to age benefits in naturalistic settings. Various factors are assumed to account for this paradox, yet empirical evidence on this issue is scarce. In 2 experiments, the present study examined the effect of task setting in…

Latent Inhibition Is Affected by Phase of Estrous Cycle in Female Rats

ERIC Educational Resources Information Center

Quinlan, Matthew G.; Duncan, Andrew; Loiselle, Catherine; Graffe, Nicole; Brake, Wayne G.

2010-01-01

Estrogen has been shown to have a strong modulatory influence on several types of cognition in both women and female rodents. Latent inhibition is a task in which pre-exposure to a neutral stimulus, such as a tone, later impedes the association of that stimulus with a particular consequence, such as a shock. Previous work from our lab demonstrates…

Failures of Sustained Attention in Life, Lab, and Brain: Ecological Validity of the SART

ERIC Educational Resources Information Center

Smilek, Daniel; Carriere, Jonathan S. A.; Cheyne, J. Allan

2010-01-01

The Sustained Attention to Response Task (SART) is a widely used tool in cognitive neuroscience increasingly employed to identify brain regions associated with failures of sustained attention. An important claim of the SART is that it is significantly related to real-world problems of sustained attention such as those experienced by TBI and ADHD…

Make Log Yield Analysis Part of Your Daily Routine

Treesearch

Jan Wiedenbeck; Jeff Palmer; Robert Mayer

2006-01-01

You haven't been conducting regular log yield studies because you don't have extra people to assign to the task. Besides, you've been around sawmills your whole life and have an innate sense of how your logs are yielding relative to the price you paid for them. Right? At the USDA Forest Service's hardwood marketing and utilization research lab in...

Automatic Synthesis of Fine-Motion Strategies for Robots.

DTIC Science & Technology

1983-12-01

ADA-A39 532 AUTOMATI CSYNTHESISOF FNE-MOTIONSTRATEGIESFORa R080 S(U) MASSACHUSETTS INS OF TECH CAMBRIDOE ARTIFCIAL INTELLGENCE LAB IOZANO-PEREZ DEC...N00014-82-K-0334 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK Artificial Intelligence Laboratory AREA...provides correct- ness criteria for compliant motion strategies. MASSACHUSETTS INSTITUTE OF TECHNOLOGY ARTIFICIAL INTELLIGENCE LABORATORY A. I. MEMO 759

Sure, They Can Build It But...Manufacturing Students Need Process Planning Skills

ERIC Educational Resources Information Center

Obi, Samuel C.

2007-01-01

Manufacturing systems students usually complete lab projects for class requirements. However, they often do not have an idea how many resources such as time, tools, and materials they will need to complete a project until they get into constructing it. Yet one of the first tasks of real-world manufacturing personnel when they receive new product…

The Complex Relationship between Students' Critical Thinking and Epistemological Beliefs in the Context of Problem Solving

ERIC Educational Resources Information Center

Hyytinen, Heidi; Holma, Katariina; Toom, Auli; Shavelson, Richard J.; Lindblom-Ylänne, Sari

2014-01-01

The study utilized a multi-method approach to explore the connection between critical thinking and epistemological beliefs in a specific problem-solving situation. Data drawn from a sample of ten third-year bioscience students were collected using a combination of a cognitive lab and a performance task from the Collegiate Learning Assessment…

Robot Programming.

DTIC Science & Technology

1982-12-01

Paris, France, June, 1982, 519-530. Latoinbe, J. C. "Equipe Intelligence Artificielle et Robotique: Etat d’avancement des recherches," Laboratoire...8217AD-A127 233 ROBOT PROGRRMMING(U) MASSACHUSETTS INST OFGTECHi/ CAMBRIDGE ARTIFICIAL INTELLIGENCE LAB T LOZANO-PEREZ UNCLASSIFIED DC8 AI-9 N884...NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK Artificial Intelligence Laboratory AREA I WORK UNIT NUMBERS ,. 545 Technology Square Cambridge

75 FR 34169 - Hewlett-Packard Company, Inkjet Consumer Solutions, HP Consumer Hardware Inkjet Lab, Including...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-16

..., Inkjet Consumer Solutions, HP Consumer Hardware Inkjet Lab, Including Leased Workers From Hightower..., applicable to all workers of Hewlett-Packard Company, Inkjet Consumer Solutions, HP Consumer Hardware Inkjet... the Department's certification is to include all workers employed at Hewlett Packard Company, Inkjet...

Bank-a-Budget

ERIC Educational Resources Information Center

Karls, Doris; Jordan, Elaine

1978-01-01

The article gives procedures for consumer foods teachers to use to actively involve students in making independent food purchasing decisions according to the school foods lab budget and food buying principles. Included are forms used to keep records for each lab: unit bank account, meat lab evaluation, and market order. (MF)

Practical Physics Labs: A Resource Manual.

ERIC Educational Resources Information Center

Goodwin, Peter

This resource manual focuses on physics labs that relate to the world around us and utilize simple equipment and situations. Forty-five laboratories are included that relate to thermodynamics, electricity, magnetism, dynamics, optics, wave transmission, centripetal force, and atomic physics. Each lab has three sections. The first section…

Portable upper extremity robotics is as efficacious as upper extremity rehabilitative therapy: a randomized controlled pilot trial.

PubMed

Page, Stephen J; Hill, Valerie; White, Susan

2013-06-01

To compare the efficacy of a repetitive task-specific practice regimen integrating a portable, electromyography-controlled brace called the 'Myomo' versus usual care repetitive task-specific practice in subjects with chronic, moderate upper extremity impairment. Sixteen subjects (7 males; mean age 57.0 ± 11.02 years; mean time post stroke 75.0 ± 87.63 months; 5 left-sided strokes) exhibiting chronic, stable, moderate upper extremity impairment. Subjects were administered repetitive task-specific practice in which they participated in valued, functional tasks using their paretic upper extremities. Both groups were supervised by a therapist and were administered therapy targeting their paretic upper extremities that was 30 minutes in duration, occurring 3 days/week for eight weeks. One group participated in repetitive task-specific practice entirely while wearing the portable robotic, while the other performed the same activity regimen manually. The upper extremity Fugl-Meyer, Canadian Occupational Performance Measure and Stroke Impact Scale were administered on two occasions before intervention and once after intervention. After intervention, groups exhibited nearly identical Fugl-Meyer score increases of ≈2.1 points; the group using robotics exhibited larger score changes on all but one of the Canadian Occupational Performance Measure and Stroke Impact Scale subscales, including a 12.5-point increase on the Stroke Impact Scale recovery subscale. Findings suggest that therapist-supervised repetitive task-specific practice integrating robotics is as efficacious as manual practice in subjects with moderate upper extremity impairment.

Application of lab derived kinetic biodegradation parameters at the field scale

NASA Astrophysics Data System (ADS)

Schirmer, M.; Barker, J. F.; Butler, B. J.; Frind, E. O.

2003-04-01

Estimating the intrinsic remediation potential of an aquifer typically requires the accurate assessment of the biodegradation kinetics, the level of available electron acceptors and the flow field. Zero- and first-order degradation rates derived at the laboratory scale generally overpredict the rate of biodegradation when applied to the field scale, because limited electron acceptor availability and microbial growth are typically not considered. On the other hand, field estimated zero- and first-order rates are often not suitable to forecast plume development because they may be an oversimplification of the processes at the field scale and ignore several key processes, phenomena and characteristics of the aquifer. This study uses the numerical model BIO3D to link the laboratory and field scale by applying laboratory derived Monod kinetic degradation parameters to simulate a dissolved gasoline field experiment at Canadian Forces Base (CFB) Borden. All additional input parameters were derived from laboratory and field measurements or taken from the literature. The simulated results match the experimental results reasonably well without having to calibrate the model. An extensive sensitivity analysis was performed to estimate the influence of the most uncertain input parameters and to define the key controlling factors at the field scale. It is shown that the most uncertain input parameters have only a minor influence on the simulation results. Furthermore it is shown that the flow field, the amount of electron acceptor (oxygen) available and the Monod kinetic parameters have a significant influence on the simulated results. Under the field conditions modelled and the assumptions made for the simulations, it can be concluded that laboratory derived Monod kinetic parameters can adequately describe field scale degradation processes, if all controlling factors are incorporated in the field scale modelling that are not necessarily observed at the lab scale. In this way, there are no scale relationships to be found that link the laboratory and the field scale, accurately incorporating the additional processes, phenomena and characteristics, such as a) advective and dispersive transport of one or more contaminants, b) advective and dispersive transport and availability of electron acceptors, c) mass transfer limitations and d) spatial heterogeneities, at the larger scale and applying well defined lab scale parameters should accurately describe field scale processes.

A mesostructured Y zeolite as a superior FCC catalyst--lab to refinery.

PubMed

García-Martínez, Javier; Li, Kunhao; Krishnaiah, Gautham

2012-12-18

A mesostructured Y zeolite was prepared by a surfactant-templated process at the commercial scale and tested in a refinery, showing superior hydrothermal stability and catalytic cracking selectivity, which demonstrates, for the first time, the promising future of mesoporous zeolites in large scale industrial applications.

The effects of different dry roast parameters on peanut quality using an industrial, belt-type roaster simulator

USDA-ARS?s Scientific Manuscript database

Recent lab scale experiments demonstrated that peanuts roasted to equivalent surface colors at different temperature/time combinations can vary substantially in chemical and physical properties related to product quality. This study expanded that approach to a pilot plant scale roaster that simulate...

Scaling of Turbulence and Transport with ρ* in LAPD

NASA Astrophysics Data System (ADS)

Guice, Daniel; Carter, Troy; Rossi, Giovanni

2014-10-01

The plasma column size of the Large Plasma Device (LAPD) is varied in order to investigate the variation of turbulence and transport with ρ* =ρs / a . The data set includes plasmas produced by the standard BaO plasma source (straight field plasma radius a 30 cm) as well as the new higher density, higher temperature LaB6 plasma source (straight field plasma radius a 10 cm). The size of the plasma column is scaled in order to observe a Bohm to Gyro-Bohm diffusion transition. The main plasma column magnetic field is held fixed while the field in the cathode region is changed in order to map the cathode to different plasma column scales in the main chamber. Past experiments in the LAPD have shown a change in the observed diffusion but no transition to Gyro-Bohm diffusion. Results will be presented from an ongoing campaign to push the LAPD into the Gyro-Bohm diffusion regime.

Development and application of network virtual instrument for emission spectrum of pulsed high-voltage direct current discharge

NASA Astrophysics Data System (ADS)

Gong, X.; Wu, Q.

2017-12-01

Network virtual instrument (VI) is a new development direction in current automated test. Based on LabVIEW, the software and hardware system of VI used for emission spectrum of pulsed high-voltage direct current (DC) discharge is developed and applied to investigate pulsed high-voltage DC discharge of nitrogen. By doing so, various functions are realized including real time collection of emission spectrum of nitrogen, monitoring operation state of instruments and real time analysis and processing of data. By using shared variables and DataSocket technology in LabVIEW, the network VI system based on field VI is established. The system can acquire the emission spectrum of nitrogen in the test site, monitor operation states of field instruments, realize real time face-to-face interchange of two sites, and analyze data in the far-end from the network terminal. By employing the network VI system, the staff in the two sites acquired the same emission spectrum of nitrogen and conducted the real time communication. By comparing with the previous results, it can be seen that the experimental data obtained by using the system are highly precise. This implies that the system shows reliable network stability and safety and satisfies the requirements for studying the emission spectrum of pulsed high-voltage discharge in high-precision fields or network terminals. The proposed architecture system is described and the target group gets the useful enlightenment in many fields including engineering remote users, specifically in control- and automation-related tasks.

An investigation of communication patterns and strategies between international teaching assistants and undergraduate students in university-level science labs

NASA Astrophysics Data System (ADS)

Gourlay, Barbara Elas

This research project investigates communication between international teaching assistants and their undergraduate students in university-level chemistry labs. During the fall semester, introductory-level chemistry lab sections of three experienced non-native speaking teaching assistants and their undergraduate students were observed. Digital audio and video recordings documented fifteen hours of lab communication, focusing on the activities and interactions in the first hour of the chemistry laboratory sessions. In follow-up one-on-one semi-structured interviews, the participants (undergraduates, teaching assistants, and faculty member) reviewed interactions and responded to a 10-item, 7-point Likert-scaled interview. Interactions were classified into success categories based on participants' opinions. Quantitative and qualitative data from the observations and interviews guided the analysis of the laboratory interactions, which examined patterns of conversational listening. Analysis of laboratory communication reveals that undergraduates initiated nearly two-thirds of laboratory communication, with three-fourths of interactions less than 30 seconds in duration. Issues of gender and topics of interaction activity were also explored. Interview data identified that successful undergraduate-teaching assistant communication in interactive science labs depends on teaching assistant listening comprehension skills to interpret and respond successfully to undergraduate questions. Successful communication in the chemistry lab depended on the coordination of visual and verbal sources of information. Teaching assistant responses that included explanations and elaborations were also seen as positive features in the communicative exchanges. Interaction analysis focusing on the listening comprehension demands placed on international teaching assistants revealed that undergraduate-initiated questions often employ deixis (exophoric reference), requiring teaching assistants to demonstrate skills at disambiguating undergraduate discourse. Interaction analysis reinforced that successful undergraduate-teaching assistant communication depends on the coordination of verbal and visual channels of communication, with the physical objects of the chemistry lab environment playing a pivotal role in expressing information and in mutual understanding. These results have implications for the evaluation of English proficiency and the preparation of non-native speaking teaching assistants by pointing out that teaching assistant listening comprehension skills and the use of contextual artifacts contribute to successful communication and are areas that, to date, have been underrepresented in the research literature on international teaching assistant communication.

On the measurement of pilot perceptual workload - A comparison of assessment techniques addressing sensitivity and intrusion issues

NASA Technical Reports Server (NTRS)

Casali, J. G.; Wierwille, W. W.

1984-01-01

A flight simulator-based study was conducted to examine fourteen distinct mental workload estimation measures, including opinion, secondary task, physiological, and primary task measures. Both the relative sensitivity of the measures to changes in mental workload and the differential intrusion of the changes on primary task performance were assessed. The flight task was varied in difficulty by manipulation of the presentation rate and complexity of a hazard-perception task that required each of 48 licensed pilots to rely heavily on their perceptual abilities. Three rating scales (Modified Cooper-Harper, Multi-descriptor, and Workload-Compensation-Interference/Technical Effectiveness), two secondary task measures (time estimation and tapping regularity), one physiological measure (respiration frequency), and one primary task measure (danger-condition response time) were reliable indicants of workload changes. Recommendations for applying the workload measures are presented.

Deoxidation Limits of Titanium Alloys during Pressure Electro Slag Remelting

NASA Astrophysics Data System (ADS)

Bartosinski, M.; Hassan-Pour, S.; Friedrich, B.; Ratiev, S.; Ryabtsev, A.

2016-07-01

This paper focuses on deoxidation of titanium alloys produced by aluminothermic reduction (ATR) and subsequent homogenizing and alloying by vacuum induction melting (VIM). The main goal of the performed research work is to outline the deoxidation limit during pressure electro slag remelting (PESR) of the described material. To obtain electrodes for deoxidation, a Ti-24Al-16V masteralloy was produced by ATR and afterwards melted in a 0.5 litre calcium- zirconate (lab scale) or 14 litres high purity calcia (pilot scale) crucibles with continuous addition of Ti-sponge after reaching liquid state in order to obtain a final Ti-6Al-4V alloy. During melting, in both cases evaporation of calcium was noticed. The cast ingots were analysed for oxygen using inert gas fusion method, matrix and alloying elements were analysed by XRF. Results show oxygen levels between 0.5 and 0.95 wt.-% for the ingots which were melted in calcium-zirconate crucibles and approx. 1 - 1.2 wt.-% for the material produced by utilization of calcia crucibles. The subsequent deoxidation was carried out in lab and pilot scale electroslag remelting furnaces using a commercially pure calcium fluoride slag and metallic calcium as deoxidation agent. It could be shown, that deoxidation of the highly contaminated material is possible applying this method to a certain limit. Pilot scale trials showed a reduction of oxygen contents by 1500 - 3500 ppm. Oxygen levels in lab scale trials showed weaker deoxidation effects. In order to describe the achieved deoxidation effects in a quantitative way, the analyzed oxygen contents of the obtained ingots are compared with calculated data resulting from a mathematical kinetic model. The modelled datasets are in good agreement with experimental oxygen values.

Traditional Labs + New Questions = Improved Student Performance.

ERIC Educational Resources Information Center

Rezba, Richard J.; And Others

1992-01-01

Presents three typical lab activities involving the breathing rate of fish, the behavior of electromagnets, and tests for water hardness to demonstrate how labs can be modified to teach process skills. Discusses how basic concepts about experimentation are developed and ways of generating and improving science experiments. Includes a laboratory…

Where Does the Energy Go?

ERIC Educational Resources Information Center

Stoeckel, Marta R.

2018-01-01

Along-standing energy lab involves dropping bouncy balls and measuring their rebound heights on successive bounces. The lab demonstrates a situation in which the mechanical energy of a system is not conserved. Although students enjoyed the lab, the author wanted to deepen their thinking about energy, including the connections to motion, with a new…

Strategic Design of an Interactive Video Learning Lab (IVL).

ERIC Educational Resources Information Center

Switzer, Ralph V., Jr.; Switzer, Jamie S.

1993-01-01

Describes a study that researched elements necessary for the design of an interactive video learning (IVL) lab for business courses. Highlights include a review of pertinent literature; guidelines for the use of an IVL lab; IVL systems integration; system specifications; hardware costs; and system software. (five references) (LRW)

Susceptibility of synthetic long-chain alkylbenzenes to degradation in reducing marine sediments

USGS Publications Warehouse

Eganhouse, Robert P.; Pontolillo, James

2008-01-01

Long-chain alkylbenzenes (LCABs) synthesized for production of alkylbenzene sulfonate surfactants have been used as molecular markers of anthropogenic waste for 25 years. Synthetic LCABs comprise two classes, the tetrapropylene-based alkylbenzenes (TABs) and the linear alkylbenzenes (LABs). LABs supplanted TABs in the mid-1960s because of improved biodegradability of their sulfonated analogs. Use of LCABs for molecular stratigraphy depends on their preservation in sediments over decadal time scales. Most laboratory and field studies suggest that LABs degrade rapidly under aerobic conditions but are resistant to degradation when oxygen is absent. However, recent work indicates that LABs may not be as persistent under reducing conditions as previously thought. To assess the potential for degradation of LCABs in reducing sediments, box cores collected in 1992 and 2003 near a submarine wastewater outfall system were analyzed using gas chromatography/mass spectrometry. The TABs were effectively preserved; differences between whole-core inventories were within analytical error. By contrast, whole-core inventories of the LABs decreased by about 50-60% during the same time interval. Based on direct comparison of chemical inventories in coeval core sections, LAB transformation rates are estimated at 0.07 ±. 0.01 yr-1. These results indicate that caution should be exercised when using synthetic LCABs for reconstruction of depositional records.

Simulations of hypervelocity impacts for asteroid deflection studies

NASA Astrophysics Data System (ADS)

Heberling, T.; Ferguson, J. M.; Gisler, G. R.; Plesko, C. S.; Weaver, R.

2016-12-01

The possibility of kinetic-impact deflection of threatening near-earth asteroids will be tested for the first time in the proposed AIDA (Asteroid Impact Deflection Assessment) mission, involving two independent spacecraft, NASAs DART (Double Asteroid Redirection Test) and ESAs AIM (Asteroid Impact Mission). The impact of the DART spacecraft onto the secondary of the binary asteroid 65803 Didymos, at a speed of 5 to 7 km/s, is expected to alter the mutual orbit by an observable amount. The velocity imparted to the secondary depends on the geometry and dynamics of the impact, and especially on the momentum enhancement factor, conventionally called beta. We use the Los Alamos hydrocodes Rage and Pagosa to estimate beta in laboratory-scale benchmark experiments and in the large-scale asteroid deflection test. Simulations are performed in two- and three-dimensions, using a variety of equations of state and strength models for both the lab-scale and large-scale cases. This work is being performed as part of a systematic benchmarking study for the AIDA mission that includes other hydrocodes.

Design of virtual display and testing system for moving mass electromechanical actuator

NASA Astrophysics Data System (ADS)

Gao, Zhigang; Geng, Keda; Zhou, Jun; Li, Peng

2015-12-01

Aiming at the problem of control, measurement and movement virtual display of moving mass electromechanical actuator(MMEA), the virtual testing system of MMEA was developed based on the PC-DAQ architecture and the software platform of LabVIEW, and the comprehensive test task such as drive control of MMEA, tests of kinematic parameter, measurement of centroid position and virtual display of movement could be accomplished. The system could solve the alignment for acquisition time between multiple measurement channels in different DAQ cards, then on this basis, the researches were focused on the dynamic 3D virtual display by the LabVIEW, and the virtual display of MMEA were realized by the method of calling DLL and the method of 3D graph drawing controls. Considering the collaboration with the virtual testing system, including the hardware drive, the measurement software of data acquisition, and the 3D graph drawing controls method was selected, which could obtained the synchronization measurement, control and display. The system can measure dynamic centroid position and kinematic position of movable mass block while controlling the MMEA, and the interface of 3D virtual display has realistic effect and motion smooth, which can solve the problem of display and playback about MMEA in the closed shell.

NEMA NU 4-2008 comparison of preclinical PET imaging systems.

PubMed

Goertzen, Andrew L; Bao, Qinan; Bergeron, Mélanie; Blankemeyer, Eric; Blinder, Stephan; Cañadas, Mario; Chatziioannou, Arion F; Dinelle, Katherine; Elhami, Esmat; Jans, Hans-Sonke; Lage, Eduardo; Lecomte, Roger; Sossi, Vesna; Surti, Suleman; Tai, Yuan-Chuan; Vaquero, Juan José; Vicente, Esther; Williams, Darin A; Laforest, Richard

2012-08-01

The National Electrical Manufacturers Association (NEMA) standard NU 4-2008 for performance measurements of small-animal tomographs was recently published. Before this standard, there were no standard testing procedures for preclinical PET systems, and manufacturers could not provide clear specifications similar to those available for clinical systems under NEMA NU 2-1994 and 2-2001. Consequently, performance evaluation papers used methods that were modified ad hoc from the clinical PET NEMA standard, thus making comparisons between systems difficult. We acquired NEMA NU 4-2008 performance data for a collection of commercial animal PET systems manufactured since 2000: microPET P4, microPET R4, microPET Focus 120, microPET Focus 220, Inveon, ClearPET, Mosaic HP, Argus (formerly eXplore Vista), VrPET, LabPET 8, and LabPET 12. The data included spatial resolution, counting-rate performance, scatter fraction, sensitivity, and image quality and were acquired using settings for routine PET. The data showed a steady improvement in system performance for newer systems as compared with first-generation systems, with notable improvements in spatial resolution and sensitivity. Variation in system design makes direct comparisons between systems from different vendors difficult. When considering the results from NEMA testing, one must also consider the suitability of the PET system for the specific imaging task at hand.

Engineering-Scale Demonstration of DuraLith and Ceramicrete Waste Forms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephson, Gary B.; Westsik, Joseph H.; Pires, Richard P.

2011-09-23

To support the selection of a waste form for the liquid secondary wastes from the Hanford Waste Immobilization and Treatment Plant, Washington River Protection Solutions (WRPS) has initiated secondary waste form testing on four candidate waste forms. Two of the candidate waste forms have not been developed to scale as the more mature waste forms. This work describes engineering-scale demonstrations conducted on Ceramicrete and DuraLith candidate waste forms. Both candidate waste forms were successfully demonstrated at an engineering scale. A preliminary conceptual design could be prepared for full-scale production of the candidate waste forms. However, both waste forms are stillmore » too immature to support a detailed design. Formulations for each candidate waste form need to be developed so that the material has a longer working time after mixing the liquid and solid constituents together. Formulations optimized based on previous lab studies did not have sufficient working time to support large-scale testing. The engineering-scale testing was successfully completed using modified formulations. Further lab development and parametric studies are needed to optimize formulations with adequate working time and assess the effects of changes in raw materials and process parameters on the final product performance. Studies on effects of mixing intensity on the initial set time of the waste forms are also needed.« less

Studying time of flight imaging through scattering media across multiple size scales (Conference Presentation)

NASA Astrophysics Data System (ADS)

Velten, Andreas

2017-05-01

Light scattering is a primary obstacle to optical imaging in a variety of different environments and across many size and time scales. Scattering complicates imaging on large scales when imaging through the atmosphere when imaging from airborne or space borne platforms, through marine fog, or through fog and dust in vehicle navigation, for example in self driving cars. On smaller scales, scattering is the major obstacle when imaging through human tissue in biomedical applications. Despite the large variety of participating materials and size scales, light transport in all these environments is usually described with very similar scattering models that are defined by the same small set of parameters, including scattering and absorption length and phase function. We attempt a study of scattering and methods of imaging through scattering across different scales and media, particularly with respect to the use of time of flight information. We can show that using time of flight, in addition to spatial information, provides distinct advantages in scattering environments. By performing a comparative study of scattering across scales and media, we are able to suggest scale models for scattering environments to aid lab research. We also can transfer knowledge and methodology between different fields.

A graphical workstation based part-task flight simulator for preliminary rapid evaluation of advanced displays

NASA Technical Reports Server (NTRS)

Wanke, Craig; Kuchar, James; Hahn, Edward; Pritchett, Amy; Hansman, R. J.

1992-01-01

Advances in avionics and display technology are significantly changing the cockpit environment in current transport aircraft. The MIT Aeronautical Systems Lab (ASL) has developed a part-task flight simulator specifically to study the effects of these new technologies on flight crew situational awareness and performance. The simulator is based on a commercially-available graphics workstation, and can be rapidly reconfigured to meet the varying demands of experimental studies. The simulator has been successfully used to evaluate graphical microburst alerting displays, electronic instrument approach plates, terrain awareness and alerting displays, and ATC routing amendment delivery through digital datalinks.

Timing considerations of Helmet Mounted Display performance

NASA Technical Reports Server (NTRS)

Tharp, Gregory; Liu, Andrew; French, Lloyd; Lai, Steve; Stark, Lawrence

1992-01-01

The Helmet Mounted Display (HMD) system developed in our lab should be a useful teleoperator systems display if it increases operator performance of the desired task; it can, however, introduce degradation in performance due to display update rate constraints and communication delays. Display update rates are slowed by communication bandwidth and/or computational power limitations. We used simulated 3D tracking and pick-and-place tasks to characterize performance levels for a range of update rates. Initial experiments with 3D tracking indicate that performance levels plateau at an update rate between 10 and 20 Hz. We have found that using the HMD with delay decreases performance as delay increases.

A view on glaucoma—are we seeing it clearly?

PubMed Central

Crabb, D P

2016-01-01

Successful clinical management of glaucoma should not simply be about control of intraocular pressure, but must equate to correct decisions about intensifying treatment when patients are at risk of developing ‘visual disability'. Yet little is known about what visual field defects, at different stages of glaucoma, specifically affect patients' abilities to perform everyday visual tasks. One way to do this is to measure patient performance in tasks in a lab setting. Another way is to ask patients themselves. The latter can be revealing and demystify views about how patients perceive the world. This short commentary highlights some of the current research in this area. PMID:26611846

Lithosphere/Asthenosphere Boundary depth inferred from global surface wave tomography

NASA Astrophysics Data System (ADS)

Burgos, G.; Montagner, J.-P.; Beucler, E.; Trampert, J.; Ritzwoller, M. H.; Capdeville, Y.; Shapiro, N. M.

2012-04-01

The coupling between the rigid lithosphere and the weaker underlying asthenosphere is a key point of Plate Tectonics and Mantle dynamics. The characterization of the properties of the Lithosphere/Asthenosphere Boundary (LAB) is essential for understanding the Upper Mantle. Recent studies, using receiver functions for example, provide local constraints. In this study a global view by surface wave tomography is given. A large amount of data from different groups (Harvard, Boulder, Utrecht, Paris) has been collected. There are more than 100,000 phase and group velocities measurements on the fundamental mode of Rayleigh and Love waves. This global scale dataset in the period range 15s-200s, enables us to investigate the LAB with an approximative lateral resolution of 500km. The regionalization of the path-averaged velocities is performed to extract isotropic and azimuthally anisotropic terms of local velocities. We derive our own crustal model (taking account of topography-bathymetry, sediments and crustal thickness) by a MonteCarlo inversion with the shorter periods of the data. A forward estimation of the LAB properties on a global map is provided. We choose a low parametrization (isotropic Vs layers) of the Upper Mantle adjusted with the larger periods of the data by MonteCarlo inversion. Then we present a new tomographic model obtained by inverting the larger periods of phase velocities in the least square sense, including isotropic Vs velocity, radial anisotropy and azimuthal anisotropy. Different proxies for the LAB are builded from this 3D Upper Mantle model, such as the strongest negative Sv velocity gradient or the variation of azimuthal anisotropy fast axis. LAB determination seems consistent in oceanic regions in all of the proxies, presenting a good correlation with ocean floor ages. While the estimated depths beneath continents still unclear depending on the type of parametrizations compared to receiver functions or heat flux studies.

Proxies of Lithosphere/Asthenosphere Boundary from global surface wave tomography

NASA Astrophysics Data System (ADS)

Burgos, G.; Montagner, J.; Beucler, E.; Trampert, J.; Ritzwoller, M. H.; Capdeville, Y.; Shapiro, N. M.

2011-12-01

The coupling between rigid lithosphere and the weaker underlying asthenosphere is a key point of Plate Tectonics and Mantle dynamics. The characterization of the properties of the Lithosphere/Asthenosphere Boundary (LAB) is essential for understanding the Upper Mantle. Recent studies, using receiver functions for example, provide local constraints. In this study a global view by surface wave tomography is given. A large amount of data from different groups (Harvard, Boulder, Utrecht, Paris) has been collected. There are more than 100,000 phase and group velocities measurements on the fundamental mode of Rayleigh and Love waves. This global scale dataset in the period range 15s-200s, enables us to investigate the LAB with an approximative lateral resolution of 500km. The regionalization of the path-averaged velocities is performed to extract isotropic and azimuthally anisotropic terms of local velocities. We derive our own crustal model (taking account of topography-bathymetry, sediments and crustal thickness) by a MonteCarlo inversion with the shorter periods of the data. A forward estimation of the LAB properties on a global map is provided. We choose a low parametrization (isotropic Vs layers) of the Upper Mantle ajusted with the larger periods of the data by MonteCarlo inversion. Then we present a new tomographic model obtained by inverting the larger periods of phase velocities in the least square sense, including isotropic Vs velocity, radial anisotropy and azimuthal anisotropy. Different proxies for the LAB are builded from this 3D Upper Mantle model, such as the strongest negative Sv velocity gradient or the variation of azimuthal anisotropy fast axis. LAB determination seems consistent in oceanic regions in all of the proxies, presenting a good correlation with ocean floor ages. While the estimated depths beneath continents still unclear depending on the type of parametrizations compared to receiver functions or heat flux studies.

Animal ethics and welfare education in wet-lab training can foster residents’ ethical values toward life

PubMed Central

Iki, Yuko; Ito, Takuya; Kudo, Katsuyoshi; Noda, Masafumi; Kanehira, Masahiko; Sueta, Teruko; Miyoshi, Ichiro; Kagaya, Yutaka; Okada, Yoshinori; Unno, Michiaki

2017-01-01

Live animals are used in surgical skills training in wet lab, which has undeniable effectiveness for the development of future surgeons. However, where such training is provided, animal welfare is a major consideration. Increasingly, institutions that offer wet-lab training are incorporating animal ethics and welfare-related content into their training courses, but the effectiveness of such animal ethics education has yet to be evaluated quantitatively. We investigated whether the animal ethics content of a training course affected trainees by measuring increase in ethical awareness using visual analog scale questionnaires before and after training. Our results demonstrated a significant and positive increase in awareness of animal ethics (significance level of 5%; 0.0380≤P≤0.0016). PMID:28592716

Animal ethics and welfare education in wet-lab training can foster residents' ethical values toward life.

PubMed

Iki, Yuko; Ito, Takuya; Kudo, Katsuyoshi; Noda, Masafumi; Kanehira, Masahiko; Sueta, Teruko; Miyoshi, Ichiro; Kagaya, Yutaka; Okada, Yoshinori; Unno, Michiaki

2017-10-30

Live animals are used in surgical skills training in wet lab, which has undeniable effectiveness for the development of future surgeons. However, where such training is provided, animal welfare is a major consideration. Increasingly, institutions that offer wet-lab training are incorporating animal ethics and welfare-related content into their training courses, but the effectiveness of such animal ethics education has yet to be evaluated quantitatively. We investigated whether the animal ethics content of a training course affected trainees by measuring increase in ethical awareness using visual analog scale questionnaires before and after training. Our results demonstrated a significant and positive increase in awareness of animal ethics (significance level of 5%; 0.0380≤P≤0.0016).

Chip in a lab: Microfluidics for next generation life science research

PubMed Central

Streets, Aaron M.; Huang, Yanyi

2013-01-01

Microfluidic circuits are characterized by fluidic channels and chambers with a linear dimension on the order of tens to hundreds of micrometers. Components of this size enable lab-on-a-chip technology that has much promise, for example, in the development of point-of-care diagnostics. Micro-scale fluidic circuits also yield practical, physical, and technological advantages for studying biological systems, enhancing the ability of researchers to make more precise quantitative measurements. Microfluidic technology has thus become a powerful tool in the life science research laboratory over the past decade. Here we focus on chip-in-a-lab applications of microfluidics and survey some examples of how small fluidic components have provided researchers with new tools for life science research. PMID:23460772

T-38 Primary Flight Display Prototyping and HIVE Support Abstract & Summary

NASA Technical Reports Server (NTRS)

Boniface, Andrew

2015-01-01

This fall I worked in EV3 within NASA's Johnson Space Center in The HIVE (Human Integrated Vehicles & Environments). The HIVE is responsible for human in the loop testing, getting new technologies in front of astronauts, operators, and users early in the development cycle to make the interfaces more human friendly. Some projects the HIVE is working on includes user interfaces for future spacecraft, wearables to alert astronauts about important information, and test beds to simulate mock missions. During my internship I created a prototype for T-38 aircraft displays using LabVIEW, learned how to use microcontrollers, and helped out with other small tasks in the HIVE. The purpose of developing a prototype for T-38 Displays in LabVIEW is to analyze functions of the display such as navigation in a cost and time effective manner. The LabVIEW prototypes allow Ellington Field AOD to easily make adjustments to the display before hardcoding the final product. LabVIEW was used to create a user interface for simulation almost identical to the real aircraft display. Goals to begin the T-38 PFD (Primary Flight Display) prototype included creating a T-38 PFD hardware display in a software environment, designing navigation for the menu's, incorporating vertical and horizontal navigation bars, and to add a heading bug for compass controls connected to the HSI (Horizontal Situation Indicator). To get started with the project, measurements of the entire display were taken. This enabled an accurate model of the hardware display to be created. Navigation of menu's required some exploration of different buttons on the display. The T-38 simulator and aircraft were used for examining the display. After one piece of the prototype was finished, another trip of to the simulator took place. This was done until all goals for the prototype were complete. Some possible integration ideas for displays in the near future are autopilot selection, touch screen displays, and crew member preferences. Complete navigation, control, and function customization will be achievable once a display is fully developed. Other than the T-38 prototyping, I spent time learning how to design small circuits and write code for them to function. This was done by adding electronic circuit components to breadboard and microcontroller then writing code to speak to those components through the microcontroller. I went through an Arduino starter kit to build circuits and code software that allowed the hardware to act. This work was planned to assist in a lighting project this fall but another solution was discovered for the lighting project. Other tasks that I assisted with, included hands on work such as mock-up construction/removal, logic analyzer repairs, and soldering with circuits. The unique opportunity to be involved work with NASA has significantly changed my educational and career goals. This opportunity has only opened the door to my career with engineering. I have learned over the span of this internship that I am fascinated by the type of work that NASA does. My desire to work in the aerospace industry has increased immensely. I hope to return to NASA to be more involved in the advancement of science, engineering, and spaceflight. My interests for my future education and career lie in NASA’s work - pioneering the future in space exploration, scientific discovery and aeronautics research.

Enabling Climate Science Investigations by Students Using Cryosphere Climate Data Records (CDRs)

NASA Astrophysics Data System (ADS)

Ledley, T. S.; Youngman, B.; Meier, W.; Bardar, E.

2010-12-01

The polar regions are particularly sensitive to changes in the climate system, and as such changes can be recognized there first. Scientists make use of this to help them develop and execute research programs that will deepen and expand our understanding of the climate system. However, the same cryosphere CDRs collected by scientists are a useful and reliable resource for helping students investigate and discover the manifestations and implications of global climate change. We have developed a number of avenues to facilitate the use of cryosphere CDRs in educational contexts. These include the Earth Exploration Toolbook (EET, http://serc.carleton.edu/eet), DataSheets (http://serc.carleton.edu/usingdata/browse_sheets.html), and Cryosphere-EarthLabs (http://serc.carleton.edu/dev/earthlabs/cryosphere). The EET is an online resource comprised of “chapters”, each of which focuses on a specific Earth science dataset and data analysis tool. Chapters provide step-by-step instructions for accessing the dataset and analysis tool, putting the data into the tool, and conducting an analysis around a specific scientific concept or issue. There are a number of EET chapters that utilize cryosphere CDRs. The EET chapter “Whither Arctic Sea Ice?” uses ~30 years of Arctic sea ice extent images and image processing software to study changes in sea ice extent. “Is Greenland Melting?” uses ice thickness data, ice melting extents and weather station data to examine the changes in the Greenland Ice Sheet. Other EET chapters that utilize cryosphere CDRs include “Using NASA NEO and ImageJ to Explore the Role of Snow Cover in Shaping Climate” and “Envisioning Climate Change Using a Global Climate Model.” In addition to creating these activities to facilitate the use of cryosphere CDRs we have also created DataSheets for these CDRs. DataSheets are educationally relevant human readable metadata about a dataset that provide both the scientific background information about the dataset as well as the topics and skills that can be taught using the dataset. DataSheets enable an educator to make effective use of a dataset outside the context of an educational activity. A DataSheet created for the sea ice index used in the “Whither Arctic Sea Ice? EET chapter is “Exploring Sea Ice Data From Satellites.” An EarthLabs module is a suite of 7-9 labs intended to be the laboratory component of a high-school capstone Earth and Space Science course. The Cryosphere-EarthLabs module focuses on sea ice to help students deepen their understanding of change over time in the climate system on multiple and embedded time scales. The module contains hands-on activities and investigations using online cryosphere CDRs to help students understand the how sea ice forms and varies, how the cryosphere changes, and the causes of those changes on time scales ranging from the seasonal to ice age time scales. In this presentation we will examine the EET and EarthLabs resources that help educators and students explore climate change using cryosphere CDRs; examine the DataSheets for these datasets; and describe how your cryosphere CDRs can be made available through these resources.

A Simple Laboratory Scale Model of Iceberg Dynamics and its Role in Undergraduate Education

NASA Astrophysics Data System (ADS)

Burton, J. C.; MacAyeal, D. R.; Nakamura, N.

2011-12-01

Lab-scale models of geophysical phenomena have a long history in research and education. For example, at the University of Chicago, Dave Fultz developed laboratory-scale models of atmospheric flows. The results from his laboratory were so stimulating that similar laboratories were subsequently established at a number of other institutions. Today, the Dave Fultz Memorial Laboratory for Hydrodynamics (http://geosci.uchicago.edu/~nnn/LAB/) teaches general circulation of the atmosphere and oceans to hundreds of students each year. Following this tradition, we have constructed a lab model of iceberg-capsize dynamics for use in the Fultz Laboratory, which focuses on the interface between glaciology and physical oceanography. The experiment consists of a 2.5 meter long wave tank containing water and plastic "icebergs". The motion of the icebergs is tracked using digital video. Movies can be found at: http://geosci.uchicago.edu/research/glaciology_files/tsunamigenesis_research.shtml. We have had 3 successful undergraduate interns with backgrounds in mathematics, engineering, and geosciences perform experiments, analyze data, and interpret results. In addition to iceberg dynamics, the wave-tank has served as a teaching tool in undergraduate classes studying dam-breaking and tsunami run-up. Motivated by the relatively inexpensive cost of our apparatus (~1K-2K dollars) and positive experiences of undergraduate students, we hope to serve as a model for undergraduate research and education that other universities may follow.

A Lab for All Reasons.

ERIC Educational Resources Information Center

Cronin-Jones, Linda L.

1990-01-01

Described is a demonstration science laboratory at the University of Florida. Discussed is laboratory design, including instructional space, lab stations, sink areas, safety areas, and a storage and distribution area. The impact of this type of design is cited. Diagrams and photographs are included. (CW)

Supercharging Lessons with a Virtual Lab

ERIC Educational Resources Information Center

Stewart, Jefferson; Vincent, Daniel

2013-01-01

The authors describes their experiences incorporating the virtual lab into a simple circuit lesson during an energy unit in a sixth-grade class. The lesson included a hands-on group experiment using wire, batteries, and light bulbs to make a circuit and an online simulation, using a virtual lab. Class discussions, student inquiries, and the study…

NOT Another Lab Report

ERIC Educational Resources Information Center

Ende, Fred

2012-01-01

Ask students to name the aspects of science class they enjoy most, and working on labs will undoubtedly be mentioned. What often won't be included, however, is writing lab reports. For many students, the process of exploration and data collection is paramount, while the explanation and analysis of findings often takes a backseat. After all, if…