A Mathematician Learns the Basics of Writing Instruction: An Immersion Experience with Long-Term Benefits

ERIC Educational Resources Information Center

Doty, Lynne L.

2012-01-01

Initially designed to be an interdisciplinary experiment that would change attitudes about mathematics, the semester-long collaboration between a writing instructor and a mathematics instructor yielded unexpected long-term results. The collaboration served as an immersion in methods and techniques used by writing instructors. Description of…

Phoenito experiments: combining the strengths of commercial crystallization automation.

PubMed

Newman, Janet; Pham, Tam M; Peat, Thomas S

2008-11-01

The use of crystallization robots for initial screening in macromolecular crystallization is well established. This paper describes how four general optimization techniques, growth-rate modulation, fine screening, seeding and additive screening, have been adapted for automation in a medium-throughput crystallization service facility. The use of automation for more challenging optimization experiments is discussed, as is a novel way of using both the Mosquito and the Phoenix nano-dispensing robots during the setup of a single crystallization plate. This dual-dispenser technique plays to the strengths of both machines.

Phoenito experiments: combining the strengths of commercial crystallization automation

PubMed Central

Newman, Janet; Pham, Tam M.; Peat, Thomas S.

2008-01-01

The use of crystallization robots for initial screening in macromolecular crystallization is well established. This paper describes how four general optimization techniques, growth-rate modulation, fine screening, seeding and additive screening, have been adapted for automation in a medium-throughput crystallization service facility. The use of automation for more challenging optimization experiments is discussed, as is a novel way of using both the Mosquito and the Phoenix nano-dispensing robots during the setup of a single crystallization plate. This dual-dispenser technique plays to the strengths of both machines. PMID:18997323

Geophysical monitoring technology for CO2 sequestration

NASA Astrophysics Data System (ADS)

Ma, Jin-Feng; Li, Lin; Wang, Hao-Fan; Tan, Ming-You; Cui, Shi-Ling; Zhang, Yun-Yin; Qu, Zhi-Peng; Jia, Ling-Yun; Zhang, Shu-Hai

2016-06-01

Geophysical techniques play key roles in the measuring, monitoring, and verifying the safety of CO2 sequestration and in identifying the efficiency of CO2-enhanced oil recovery. Although geophysical monitoring techniques for CO2 sequestration have grown out of conventional oil and gas geophysical exploration techniques, it takes a long time to conduct geophysical monitoring, and there are many barriers and challenges. In this paper, with the initial objective of performing CO2 sequestration, we studied the geophysical tasks associated with evaluating geological storage sites and monitoring CO2 sequestration. Based on our review of the scope of geophysical monitoring techniques and our experience in domestic and international carbon capture and sequestration projects, we analyzed the inherent difficulties and our experiences in geophysical monitoring techniques, especially, with respect to 4D seismic acquisition, processing, and interpretation.

Electrostatic Discharge Initiation Experiments using PVDF Pressure Transducers

DTIC Science & Technology

1991-12-01

ignition sensitivity. The results are discussed within the context of a preliminary model of electrostatic initiation. iii/iv NAVSWC TR 91-666 CONTENTS...Chapter Page 1 INTRODUCTION .......................................... 1-1 TWO PHASE IGNITION MODEL ....................... 1-1 SENSITIZING FACTORS...is necessary to establish effective techniques to reduce the hazards associated with ESD ignition. TWO-PHASE IGNITION MODEL A model has been proposed

A Study of the Effects of Microteaching Experiences Upon the Classroom Behavior of Social Studies Student Teachers.

ERIC Educational Resources Information Center

Limbacher, Philip C.

The hypotheses of this field study, conducted in connection with the Teaching Techniques Laboratory at the University of Illinois, were that student teachers who had participated in a supervised, laboratory, microteaching experience would: 1) receive more favorable pupil evaluations of an initial and final teaching effort on the Teacher…

Association of Modality with Mortality among Canadian Aboriginals

PubMed Central

Hemmelgarn, Brenda; Rigatto, Claudio; Komenda, Paul; Yeates, Karen; Promislow, Steven; Mojica, Julie; Tangri, Navdeep

2012-01-01

Summary Background and objectives Previous studies have shown that Aboriginals and Caucasians experience similar outcome on dialysis in Canada. Using the Canadian Organ Replacement Registry, this study examined whether dialysis modality (peritoneal or hemodialysis) impacted mortality in Aboriginal patients. Design, setting, participants, & measurements This study identified 31,576 adult patients (hemodialysis: Aboriginal=1839, Caucasian=21,430; peritoneal dialysis: Aboriginal=554, Caucasian=6769) who initiated dialysis between January of 2000 and December of 2009. Aboriginal status was identified by self-report. Dialysis modality was determined 90 days after dialysis initiation. Multivariate Cox proportional hazards and competing risk models were constructed to determine the association between race and mortality by dialysis modality. Results During the study period, 939 (51.1%) Aboriginals and 12,798 (53.3%) Caucasians initiating hemodialysis died, whereas 166 (30.0%) and 2037 (30.1%), respectively, initiating peritoneal dialysis died. Compared with Caucasians, Aboriginals on hemodialysis had a comparable risk of mortality (adjusted hazards ratio=1.04, 95% confidence interval=0.96–1.11, P=0.37). However, on peritoneal dialysis, Aboriginals experienced a higher risk of mortality (adjusted hazards ratio=1.36, 95% confidence interval=1.13–1.62, P=0.001) and technique failure (adjusted hazards ratio=1.29, 95% confidence interval=1.03–1.60, P=0.03) than Caucasians. The risk of technique failure varied by patient age, with younger Aboriginals (<50 years old) more likely to develop technique failure than Caucasians (adjusted hazards ratio=1.76, 95% confidence interval=1.23–2.52, P=0.002). Conclusions Aboriginals on peritoneal dialysis experience higher mortality and technique failure relative to Caucasians. Reasons for this race disparity in peritoneal dialysis outcomes are unclear. PMID:22997343

Twenty and thirty GHz millimeter wave experiments with the ATS-6 satellite

NASA Technical Reports Server (NTRS)

Ippolito, L. J.

1976-01-01

Studies at 11 locations in the continental United States were directed at an evaluation of rain attenuation effects, scintillations, depolarization, site diversity, coherence bandwidth, and analog and digital communications techniques using the Applications Technology Satellite-6(ATS-6). In addition to direct measurements on the 20- and 30-GHz links, methods of attenuation prediction with radars, rain gages, and radiometers were developed and compared with the directly measured attenuation. Initial data results of the ATS-6 millimeter wave experiment were presented. The first section describes the experiment objectives, flight hardware, and modes of operation. The remaining six sections present papers prepared by the major participating organizations in the experiment. The papers present a comprehensive summary of the significant results of the initial 11 months of ATS-6 experiment measurements and related radiometric, radar, and radio-meteorology studies.

Observing the Communication Behavior of Deaf-Blind Children

ERIC Educational Resources Information Center

Tweedie, David

1974-01-01

Reviewed are observational techniques for rating the communication of deaf-blind multihandicapped children, and reported is an initial study of the diagnostic observational competency of 75 speech pathologists at 5 levels of training and experience. (LC)

Results of the Greenland ice sheet model initialisation experiments: ISMIP6 - initMIP-Greenland

NASA Astrophysics Data System (ADS)

Goelzer, Heiko; Nowicki, Sophie; Edwards, Tamsin; Beckley, Matthew

2017-04-01

Ice sheet model initialisation has a large effect on projected future sea-level contributions and gives rise to important uncertainties. The goal of this intercomparison exercise for the continental-scale Greenland ice sheet is therefore to compare, evaluate and improve the initialisation techniques used in the ice sheet modelling community. The initMIP-Greenland project is the first in a series of ice sheet model intercomparison activities within ISMIP6 (Ice Sheet Model Intercomparison Project for CMIP6). The experimental set-up has been designed to allow comparison of the initial present-day state of the Greenland ice sheet between participating models and against observations. Furthermore, the initial states are tested with two schematic forward experiments to evaluate the initialisation in terms of model drift (forward run without any forcing) and response to a large perturbation (prescribed surface mass balance anomaly). We present and discuss results that highlight the wide diversity of data sets, boundary conditions and initialisation techniques used in the community to generate initial states of the Greenland ice sheet.

Plasma Discharge Initiation of Explosives in Rock Blasting Application: A Case Study

NASA Astrophysics Data System (ADS)

Jae-Ou, Chae; Young-Jun, Jeong; V, M. Shmelev; A, A. Denicaev; V, M. Poutchkov; V, Ravi

2006-07-01

A plasma discharge initiation system for the explosive volumetric combustion charge was designed, investigated and developed for practical application. Laboratory scale experiments were carried out before conducting the large scale field tests. The resultant explosions gave rise to less noise, insignificant seismic vibrations and good specific explosive consumption for rock blasting. Importantly, the technique was found to be safe and environmentally friendly.

Exploring Ultrafast Structural Dynamics for Energetic Enhancement or Disruption

DTIC Science & Technology

2016-03-01

it. In a pump -push/ dump probe experiment, a secondary laser pulse (push/ dump ) is used after the initial perturbation due to the pump pulse. The...increased. The pump -push/ dump probe technique is a difficult experiment that requires a highly stable laser source. Ultrafast pump -probe experiments...decomposition of solids. Journal of Applied Physics. 2001;89:4156–4166. 17. Kee TW. Femtosecond pump -push-probe and pump - dump -probe spectroscopy of

MSFC Skylab experimenter's reference

NASA Technical Reports Server (NTRS)

1974-01-01

The methods and techniques for experiment development and integration that evolved during the Skylab Program are described to facilitate transferring this experience to experimenters in future manned space programs. Management responsibilities and the sequential process of experiment evolution from initial concept through definition, development, integration, operation and postflight analysis are outlined in the main text and amplified, as appropriate, in appendixes. Emphasis is placed on specific lessons learned on Skylab that are worthy of consideration by future programs.

Own and Others' Prior Experiences Influence Children's Imitation of Causal Acts.

PubMed

Williamson, Rebecca A; Meltzoff, Andrew N

2011-07-01

Young children learn from others' examples, and they do so selectively. We examine whether the efficacy of prior experiences influences children's imitation. Thirty-six-month-olds had initial experience on a causal learning task either by performing the task themselves or by watching an adult perform it. The nature of the experience was manipulated such that the actor had either an easy or a difficult experience completing the task. Next, a second adult demonstrated an innovative technique for completing it. Children who had a difficult first-person experience, and those who had witnessed another person having difficulty, were significantly more likely to adopt and imitate the adult's innovation than those who had or witnessed an easy experience. Children who observed another were also more likely to imitate than were those who had the initial experience themselves. Imitation is influenced by prior experience, both when it is obtained through one's own hands-on motor manipulation and when it derives from observing the acts of others.

Application of neutron interrogation techniques to corrosion detection

NASA Technical Reports Server (NTRS)

Birt, E. A.; Namkung, M.; Vulcan, W.; Welsh, R. E.

1991-01-01

This paper discusses a technique which may be able to detect corrosion by determining the presence of oxygen at the corroded site via a neutron inelastic gamma reaction. Initial experiments have been performed using a Pu-239/Be neutron source and a NaI(T1) gamma-ray detector. From the results it was concluded that a 1 mm thickness of aluminum oxide would not be detected.

Action Socialization Experiences at the New Jersey School of Conservation. Revised Fall 1977.

ERIC Educational Resources Information Center

Merritt, James K.

The Action Socialization Experiences (ASE) presented in this guide are modified Outward Bound initiative tests developed at the New Jersey School of Conservation to be used as an introduction to group problem solving. The ASE process is described as follows: teachers are assigned a specific problem for a 2-hour period and briefed on techniques of…

Giant cane propagation techniques for use in restoration of riparian forest ecosystems

Treesearch

Rebecca L. Sexton; James J. Zaczek; John W. Groninger; Stephen D. Fillmore; Karl W. J. Williard

2003-01-01

This study was initiated to determine factors important for rhizome cutting propagation of giant cane for use in canebreak restoration. Experiment I showed that greater numbers of culms were produced for rhizomes with more internodes especially when surface planted rather than buried. Experiment II determined that 76 percent of the 435 rhizomes tested produced at least...

Generation of a Realistic Soil Moisture Initialization System and its Potential Impact on Short-to-Seasonal Forecasting of Near Surface Variables

NASA Astrophysics Data System (ADS)

Boisserie, M.; Cocke, S.; O'Brien, J. J.

2009-12-01

Although the amount of water contained in the soil seems insignificant when compared to the total amount of water on a global-scale, soil moisture is widely recognized as a crucial variable for climate studies. It plays a key role in regulating the interaction between the atmosphere and the land-surface by controlling the repartition between the surface latent and sensible heat fluxes. In addition, the persistence of soil moisture anomalies provides one of the most important components of memory for the climate system. Several studies have shown that, during the boreal summer in mid-latitudes, the soil moisture role in controlling the continental precipitation variability may be more important than that of the sea surface temperature (Koster et al. 2000, Hong and Kalnay 2000, Koster et al. 2000, Kumar and Hoerling 1995, Trenberth et al. 1998, Shukla 1998). Although all of the above studies have demonstrated the strong sensitivity of seasonal forecasts to the soil moisture initial conditions, they relied on extreme or idealized soil moisture levels. The question of whether realistic soil moisture initial conditions lead to improved seasonal predictions has not been adequately addressed. Progress in addressing this question has been hampered by the lack of long-term reliable observation-based global soil moisture data sets. Since precipitation strongly affects the soil moisture characteristics at the surface and in depth, an alternative to this issue is to assimilate precipitation. Because precipitation is a diagnostic variable, most of the current reanalyses do not directly assimilate it into their models (M. Bosilovitch, 2008). In this study, an effective technique that directly assimilates the precipitation is used. We examine two experiments. In the first experiment, the model is initialized by directly assimilating a global, 3-hourly, 1.0° precipitation dataset, provided by Sheffield et al. (2006), in a continuous assimilation period of a couple of months. For this, we use a technique named the Precipitation Assimilation Reanalysis (PAR) described in Nunes and Cocke (2004). This technique consists of modifying the vertical profile of humidity as a function of the observed and predicted model rain rates. In the second experiment, the model is initialized without precipitation assimilation. For each experiment, ten sets of seasonal forecasts of the coupled land-atmosphere Florida State University/Center for Ocean and Atmosphere Predictions Studies (FSU/COAPS) model were generated, starting from the boreal summer of each year between 1986 and 1995. For each forecast, ten ensembles are produced by starting the forecast from the 1st and the 15th of each month from April to August. The results of these experiments show, first, that the PAR technique greatly improves the temporal and spatial variability of out model soil moisture estimate. Second, using these realistic soil moisture initial conditions, we found a significant increase in the air temperature seasonal forecasting skills. However, not significant increase has been found in the precipitation seasonal forecasting skills. The results of this study are involved in the GLACE-2 international multi-model experiment.

A compressed sensing based approach on Discrete Algebraic Reconstruction Technique.

PubMed

Demircan-Tureyen, Ezgi; Kamasak, Mustafa E

2015-01-01

Discrete tomography (DT) techniques are capable of computing better results, even using less number of projections than the continuous tomography techniques. Discrete Algebraic Reconstruction Technique (DART) is an iterative reconstruction method proposed to achieve this goal by exploiting a prior knowledge on the gray levels and assuming that the scanned object is composed from a few different densities. In this paper, DART method is combined with an initial total variation minimization (TvMin) phase to ensure a better initial guess and extended with a segmentation procedure in which the threshold values are estimated from a finite set of candidates to minimize both the projection error and the total variation (TV) simultaneously. The accuracy and the robustness of the algorithm is compared with the original DART by the simulation experiments which are done under (1) limited number of projections, (2) limited view problem and (3) noisy projections conditions.

Protein crystal growth results from the United States Microgravity Laboratory-1 mission

NASA Technical Reports Server (NTRS)

Delucas, Lawrence J.; Moore, K. M.; Vanderwoerd, M.; Bray, T. L.; Smith, C.; Carson, M.; Narayana, S. V. L.; Rosenblum, W. M.; Carter, D.; Clark, A. D, Jr.

1994-01-01

Protein crystal growth experiments have been performed by this laboratory on 18 Space Shuttle missions since April, 1985. In addition, a number of microgravity experiments also have been performed and reported by other investigators. These Space Shuttle missions have been used to grow crystals of a variety of proteins using vapor diffusion, liquid diffusion, and temperature-induced crystallization techniques. The United States Microgravity Laboratory - 1 mission (USML-1, June 25 - July 9, 1992) was a Spacelab mission dedicated to experiments involved in materials processing. New protein crystal growth hardware was developed to allow in orbit examination of initial crystal growth results, the knowledge from which was used on subsequent days to prepare new crystal growth experiments. In addition, new seeding hardware and techniques were tested as well as techniques that would prepare crystals for analysis by x-ray diffraction, a capability projected for the planned Space Station. Hardware that was specifically developed for the USML-1 mission will be discussed along with the experimental results from this mission.

Seasonal predictions of equatorial Atlantic SST in a low-resolution CGCM with surface heat flux correction

NASA Astrophysics Data System (ADS)

Dippe, Tina; Greatbatch, Richard; Ding, Hui

2016-04-01

The dominant mode of interannual variability in tropical Atlantic sea surface temperatures (SSTs) is the Atlantic Niño or Zonal Mode. Akin to the El Niño-Southern Oscillation in the Pacific sector, it is able to impact the climate both of the adjacent equatorial African continent and remote regions. Due to heavy biases in the mean state climate of the equatorial-to-subtropical Atlantic, however, most state-of-the-art coupled global climate models (CGCMs) are unable to realistically simulate equatorial Atlantic variability. In this study, the Kiel Climate Model (KCM) is used to investigate the impact of a simple bias alleviation technique on the predictability of equatorial Atlantic SSTs. Two sets of seasonal forecasting experiments are performed: An experiment using the standard KCM (STD), and an experiment with additional surface heat flux correction (FLX) that efficiently removes the SST bias from simulations. Initial conditions for both experiments are generated by the KCM run in partially coupled mode, a simple assimilation technique that forces the KCM with observed wind stress anomalies and preserves SST as a fully prognostic variable. Seasonal predictions for both sets of experiments are run four times yearly for 1981-2012. Results: Heat flux correction substantially improves the simulated variability in the initialization runs for boreal summer and fall (June-October). In boreal spring (March-May), however, neither the initialization runs of the STD or FLX-experiments are able to capture the observed variability. FLX-predictions show no consistent enhancement of skill relative to the predictions of the STD experiment over the course of the year. The skill of persistence forecasts is hardly beat by either of the two experiments in any season, limiting the usefulness of the few forecasts that show significant skill. However, FLX-forecasts initialized in May recover skill in July and August, the peak season of the Atlantic Niño (anomaly correlation coefficients of about 0.3). Further study is necessary to determine the mechanism that drives this potentially useful recovery.

A study to define an in-flight dynamics measurement and data applications program for space shuttle payloads

NASA Technical Reports Server (NTRS)

Rader, W. P.; Barrett, S.; Payne, K. R.

1975-01-01

Data measurement and interpretation techniques were defined for application to the first few space shuttle flights, so that the dynamic environment could be sufficiently well established to be used to reduce the cost of future payloads through more efficient design and environmental test techniques. It was concluded that: (1) initial payloads must be given comprehensive instrumentation coverage to obtain detailed definition of acoustics, vibration, and interface loads, (2) analytical models of selected initial payloads must be developed and verified by modal surveys and flight measurements, (3) acoustic tests should be performed on initial payloads to establish realistic test criteria for components and experiments in order to minimize unrealistic failures and retest requirements, (4) permanent data banks should be set up to establish statistical confidence in the data to be used, (5) a more unified design/test specification philosophy is needed, (6) additional work is needed to establish a practical testing technique for simulation of vehicle transients.

The NASA Software Research Infusion Initiative: Successful Technology Transfer for Software Assurance

NASA Technical Reports Server (NTRS)

Hinchey, Michael G.; Pressburger, Thomas; Markosian, Lawrence; Feather, Martin S.

2006-01-01

New processes, methods and tools are constantly appearing in the field of software engineering. Many of these augur great potential in improving software development processes, resulting in higher quality software with greater levels of assurance. However, there are a number of obstacles that impede their infusion into software development practices. These are the recurring obstacles common to many forms of research. Practitioners cannot readily identify the emerging techniques that may most benefit them, and cannot afford to risk time and effort in evaluating and experimenting with them while there is still uncertainty about whether they will have payoff in this particular context. Similarly, researchers cannot readily identify those practitioners whose problems would be amenable to their techniques and lack the feedback from practical applications necessary to help them to evolve their techniques to make them more likely to be successful. This paper describes an ongoing effort conducted by a software engineering research infusion team, and the NASA Research Infusion Initiative, established by NASA s Software Engineering Initiative, to overcome these obstacles.

Outplanting technique, host genotype, and site affect the initial success of outplanted Acropora cervicornis

PubMed Central

Gilliam, David S.

2018-01-01

Acropora cervicornis is the most widely used coral species for reef restoration in the greater Caribbean. However, outplanting methodologies (e.g., colony density, size, host genotype, and attachment technique) vary greatly, and to date have not been evaluated for optimality across multiple sites. Two experiments were completed during this study, the first evaluated the effects of attachment technique, colony size, and genotype by outplanting 405 A. cervicornis colonies, from ten genotypes, four size classes, and three attachment techniques (epoxy, nail and cable tie, or puck) across three sites. Colony survival, health condition, tissue productivity, and growth were assessed across one year for this experiment. The second experiment assessed the effect of colony density by outplanting colonies in plots of one, four, or 25 corals per 4 m2 across four separate sites. Plot survival and condition were evaluated across two years for this experiment in order to better capture the effect of increasing cover. Colonies attached with a nail and cable tie resulted in the highest survival regardless of colony size. Small corals had the lowest survival, but the greatest productivity. The majority of colony loss was attributed to missing colonies and was highest for pucks and small epoxied colonies. Disease and predation were observed at all sites, but did not affect all genotypes, however due to the overall low prevalence of either condition there were no significant differences found in any comparison. Low density plots had significantly higher survival and significantly lower prevalence of disease, predation, and missing colonies than high density plots. These results indicate that to increase initial outplant success, colonies of many genotypes should be outplanted to multiple sites using a nail and cable tie, in low densities, and with colonies over 15 cm total linear extension. PMID:29507829

Experiments on Four Different Techniques for Automatically Locating Land Vehicles - A Summary of Results

DOT National Transportation Integrated Search

1977-06-01

In 1975, to further the development and to refine and dmonstrate multiuser Automatic Vehicle Monitoring (AVM) application, the Urban Mass Transportation Administration and the Transportation Systems Center (TSC) initiated a two-phase program. Phase I...

Modulation Spectroscopy and Opto Mechanics of Micro Toroidal Resonators

DTIC Science & Technology

2017-08-01

campus at UTRGV, 2) to initiate training of the UTRGV students in nano fabrication and clean room techniques, 3) to conduct experiments with silicon...Email: Volker.Quetschke@utb.edu RPPR Final Report as of 30-Oct-2017 Training Opportunities: During this reporting period PI and his students acquired...Lithography (EBL), Scanning Electron Microscope (SEM), and Reactive Ion-Etching (RIE) techniques. The students involved in this project attended the

Initial experience using the rigid forceps technique to remove wall-embedded IVC filters.

PubMed

Avery, Allan; Stephens, Maximilian; Redmond, Kendal; Harper, John

2015-06-01

Severely tilted and embedded inferior vena cava (IVC) filters remain the most challenging IVC filters to remove. Heavy endothelialisation over the filter hook can prevent engagement with standard snare and cone recovery techniques. The rigid forceps technique offers a way to dissect the endothelial cap and reliably retrieve severely tilted and embedded filters. By developing this technique, failed IVC retrieval rates can be significantly reduced and the optimum safety profile offered by temporary filters can be achieved. We present our initial experience with the rigid forceps technique described by Stavropoulos et al. for removing wall-embedded IVC filters. We retrospectively reviewed the medical imaging and patient records of all patients who underwent a rigid forceps filter removal over a 22-month period across two tertiary referral institutions. The rigid forceps technique had a success rate of 85% (11/13) for IVC filter removals. All filters in the series showed evidence of filter tilt and embedding of the filter hook into the IVC wall. Average filter tilt from the Z-axis was 19 degrees (range 8-56). Filters observed in the case study were either Bard G2X (n = 6) or Cook Celect (n = 7). Average filter dwell time was 421 days (range 47-1053). There were no major complications observed. The rigid forceps technique can be readily emulated and is a safe and effective technique to remove severely tilted and embedded IVC filters. The development of this technique across both institutions has increased the successful filter removal rate, with perceived benefits to the safety profile of our IVC filter programme. © 2015 The Royal Australian and New Zealand College of Radiologists.

Survival for haemodialysis vs. peritoneal dialysis and technique transference. Experience in Ourense, Spain, from 1976 to 2012.

PubMed

Otero González, Alfonso; Iglesias Forneiro, Alfonso; Camba Caride, María Jesús; Pérez Melón, Cristina; Borrajo Prol, María Paz; Novoa Fernández, Enrique; Arenas Moncaleano, Ivan Gilberto; Uribe Moya, Silvia; Lagoa Labrador, Fiz

2015-01-01

To assess SV in our RRT population in the period 1976-2012 as well as the influence of technique transference (TT). The study included a retrospective cohort of 993 patients. Data were classified as transplant (Tx), change in technique, exitus or lost to follow-up. SV for TT was determined in patients with over 12 weeks of permanence. The mortality risk adjusted for age, sex, dialysis technique or diabetes mellitus (DM) showed that the estimated risk of death increased by 4.8% per year increase (HR=1.048; 95% CI: 1.04-1.06; P<.001) and was 44% higher in diabetics compared to non-diabetics (HR=1.44; 95% CI 1.16-1.76; P<.01). Regarding SV for TT, patients who initiated HD had a shorter survival than those who initiated PD and transferred to HD (P=.00563). In our experience, SV in RRT is dependent on age and coexistence of DM. It would be beneficial to reinstate the concept of "comprehensive care", in which RRT would start with PD and later transfer to HD. Copyright © 2015 Sociedad Española de Nefrología. Published by Elsevier España, S.L.U. All rights reserved.

Improving the Leader Development Experience in Army Units

DTIC Science & Technology

2013-04-01

conditions and creating a “ sweet spot” between order and chaos and simplicity and complexity, leaders can modify the experience to better align it with...subordinates to exercise initiative, overcome adversity, consider innovative solutions, or taste failure may not achieve maximum growth and are not...division commander’s behavior, preferences , and priorities become known down to battalion and lower levels.49 Some might view these techniques as

Optical Techniques for the Remote Detection of Biological Aerosols

DTIC Science & Technology

1974-08-01

1) Laboratory exneriments (2) Remote detection experiments. In the first phase , the optical characteristics of several selected biological...the-art optical sensor system. The estimates were favorable, and a second research phase was initiated. Remote detection experiments were conducted...that of phase fluorometry. The fluorescence is excited by 3. continuous light source, the output of which is modulated at a high freeuency by an optical

Therapist and client predictors of use of therapy techniques within the context of implementation efforts in a large public mental health system

PubMed Central

Wolk, Courtney Benjamin; Marcus, Steven C.; Weersing, V. Robin; Hawley, Kristin M.; Evans, Arthur; Hurford, Matthew; Beidas, Rinad

2016-01-01

Objective Many youth receiving community mental health treatment do not receive evidence-based interventions. Research suggests that community mental health therapists use a broad range of therapeutic techniques at low intensities. The present study examined the relationship between therapist- and client-level predictors on community-based therapists’ report of cognitive, behavioral, psychodynamic, and family techniques within the context of implementation efforts. Methods One hundred thirty therapists from 23 organizations in an urban publicly funded behavioral health system implementing evidence-based practices participated. Therapist-level predictors included age, gender, clinical experience, licensure status, and participation in evidence-based practice initiatives. Child-level predictors included therapist-reported child primary disorder (i.e., externalizing, internalizing, or other) and child age. Therapists completed the Therapist Procedures Checklist- Family Revised, a self-report measure of therapeutic techniques used. Results Unlicensed therapists were more likely to report use of both psychodynamic and behavioral techniques. Therapists who did not participate in an evidence-based practice initiative were less likely to report use of cognitive techniques. Those with externalizing clients were more likely to report use of behavioral and family techniques. Therapists with the youngest clients (aged 3-7) were most likely to report use of behavioral techniques and less likely to report use of cognitive and psychodynamic techniques. Conclusions Results suggest that both therapist and client factors predict self-reported use of therapy techniques. Participating in an evidence-based practice initiative increased report of cognitive techniques. Therapists reported using more behavioral and family techniques for youth with externalizing disorders and fewer cognitive and psychodynamic techniques with young clients. PMID:26876658

Total Reconstruction of the Auricle: Our Experiences on Indications and Recent Techniques

PubMed Central

Storck, K.; Staudenmaier, R.; Buchberger, M.; Strenger, T.; Kreutzer, K.; von Bomhard, A.; Stark, T.

2014-01-01

Introduction. Auricular reconstruction is a great challenge in facial plastic surgery. With the advances in surgical techniques and biotechnology, different options are available for consideration. The aim of this paper is to review the knowledge about the various techniques for total auricular reconstruction based on the literature and our experience. Methods. Approximately 179 articles published from 1980 to 2013 were identified, and 59 articles were included. We have focused on the current status of total auricular reconstruction based on our personal experience and on papers of particular interest, published within the period of review. We have also included a prospective view on the tissue engineering of cartilage. Results. Most surgeons still practice total auricular reconstruction by employing techniques developed by Brent, Nagata, and Firmin with autologous rib cartilage. Within the last years, alloplastic frameworks for reconstruction have become well established. Choosing the reconstruction techniques depends mainly on the surgeon's preference and experience. Prosthetic reconstruction is still reserved for special conditions, even though the material is constantly improving. Tissue engineering has a growing potential for clinical applicability. Conclusion. Auricular reconstruction still receives attention of plastic/maxillofacial surgeons and otolaryngologists. Even though clinical applicability lags behind initial expectations, the development of tissue-engineered constructs continues its potential development. PMID:24822198

Sensitivity of Forecast Skill to Different Objective Analysis Schemes

NASA Technical Reports Server (NTRS)

Baker, W. E.

1979-01-01

Numerical weather forecasts are characterized by rapidly declining skill in the first 48 to 72 h. Recent estimates of the sources of forecast error indicate that the inaccurate specification of the initial conditions contributes substantially to this error. The sensitivity of the forecast skill to the initial conditions is examined by comparing a set of real-data experiments whose initial data were obtained with two different analysis schemes. Results are presented to emphasize the importance of the objective analysis techniques used in the assimilation of observational data.

[Application possibilities and initial experience with digital volume tomography in hand and wrist imaging].

PubMed

Goerke, Sebastian M; Neubauer, J; Zajonc, H; Thiele, J R; Kotter, E; Langer, M; Stark, G B; Lampert, F M

2015-02-01

During the last decade, DVT (digital volume tomography) imaging has become a widely used standard technique in head and neck imaging. Lower radiation exposure compared to conventional computed tomography (MDCT) has been described. Recently, DVT has been developed as an extremity scanner and as such represents a new imaging technique for hand surgery. We here describe the first 24 months experience with this new imaging modality in hand and wrist imaging by presenting representative cases and by describing the technical background. Furthermore, the method's advantages and disadvantages are discussed with reference to the given literature. © Georg Thieme Verlag KG Stuttgart · New York.

Endovascular balloon-assisted embolization of high-flow peripheral vascular lesions using dual-lumen coaxial balloon microcatheter and Onyx: initial experience.

PubMed

Jagadeesan, Bharathi D; Mortazavi, Shabnam; Hunter, David W; Duran-Castro, Olga L; Snyder, Gregory B; Siedel, Glen F; Golzarian, Jafar

2014-04-01

Balloon-assisted embolization performed by delivering Onyx ethylene vinyl alcohol copolymer through a dual-lumen coaxial balloon microcatheter is a new technique for the management of peripheral vascular lesions. This technique does not require an initial reflux of Onyx to form around the tip of the microcatheter before antegrade flow of Onyx can commence. In a series of four patients who were treated with the use of this technique, the absence of significant reflux of Onyx was noted, as were excellent navigability and easy retrieval of the balloon microcatheter. However, in one patient, there was inadvertent adverse embolization of a digital artery, which was not caused by reflux of Onyx but could still be related to balloon inflation. © 2013 SIR Published by SIR All rights reserved.

Ground testing on the nonvented fill method of orbital propellant transfer: Results of initial test series

NASA Technical Reports Server (NTRS)

Chato, David J.

1991-01-01

The results are presented of a series of no-vent fill experiments conducted on a 175 cu ft flightweight hydrogen tank. The experiments consisted of the nonvented fill of the tankage with liquid hydrogen using two different inlet systems (top spray, and bottom spray) at different tank initial conditions and inflow rates. Nine tests were completed of which six filled in excess of 94 percent. The experiments demonstrated a consistent and repeatable ability to fill the tank in excess of 94 percent using the nonvented fill technique. Ninety-four percent was established as the high level cutoff due to requirements for some tank ullage to prevent rapid tank pressure rise which occurs in a tank filled entirely with liquid. The best fill was terminated at 94 percent full with a tank internal pressure less than 26 psia. Although the baseline initial tank wall temperature criteria was that all portions of the tank wall be less than 40 R, fills were achieved with initial wall temperatures as high as 227 R.

Recent results and new hardware developments for protein crystal growth in microactivity

NASA Technical Reports Server (NTRS)

Delucas, L. J.; Long, M. M.; Moore, K. M.; Smith, C.; Carson, M.; Narayana, S. V. L.; Carter, D.; Clark, A. D., Jr.; Nanni, R. G.; Ding, J.

1993-01-01

Protein crystal growth experiments have been performed on 16 space shuttle missions since April, 1985. The initial experiments utilized vapor diffusion crystallization techniques similar to those used in laboratories for earth-based experiments. More recent experiments have utilized temperature induced crystallization as an alternative method for growing high quality protein crystals in microgravity. Results from both vapor diffusion and temperature induced crystallization experiments indicate that proteins grown in microgravity may be larger, display more uniform morphologies, and yield diffraction data to significantly higher resolutions than the best crystals of these proteins grown on earth.

Role of radiology in a national initiative to interdict drug smuggling: the Dutch experience.

PubMed

Algra, Paul R; Brogdon, Byron G; Marugg, Roque C

2007-08-01

The purpose of this pictorial essay is to describe the role of radiology in a national initiative to intercept illegal narcotics concealed within the bodies of human transporters. Radiologic examination is increasingly important in identifying intracorporeal drug smuggling as improved wrapping techniques undermine the usefulness of blood and urine testing and clinical observation. Detection rates of high accuracy, sensitivity, and specificity are achieved by experienced radiologists.

Zonal Acoustic Velocimetry in 30-cm, 60-cm, and 3-m Laboratory Models of the Outer Core

NASA Astrophysics Data System (ADS)

Rojas, R.; Doan, M. N.; Adams, M. M.; Mautino, A. R.; Stone, D.; Lekic, V.; Lathrop, D. P.

2016-12-01

A knowledge of zonal flows and shear is key in understanding magnetic field dynamics in the Earth and laboratory experiments with Earth-like geometries. Traditional techniques for measuring fluid flow using visualization and particle tracking are not well-suited to liquid metal flows. This has led us to develop a flow measurement technique based on acoustic mode velocimetry adapted from helioseismology. As a first step prior to measurements in the liquid sodium experiments, we implement this technique in our 60-cm diameter spherical Couette experiment in air. To account for a more realistic experimental geometry, including deviations from spherical symmetry, we compute predicted frequencies of acoustic normal modes using the finite element method. The higher accuracy of the predicted frequencies allows the identification of over a dozen acoustic modes, and mode identification is further aided by the use of multiple microphones and by analyzing spectra together with those obtained at a variety of nearby Rossby numbers. Differences between the predicted and observed mode frequencies are caused by differences in flow patterns present in the experiment. We compare acoustic mode frequency splittings with theoretical predictions for stationary fluid and solid body flow condition with excellent agreement. We also use this technique to estimate the zonal shear in those experiments across a range of Rossby numbers. Finally, we report on initial attempts to use this in liquid sodium in the 3-meter diameter experiment and parallel experiments performed in water in the 30-cm diameter experiment.

Initial experience with custom-fit total knee replacement: intra-operative events and long-leg coronal alignment.

PubMed

Spencer, Brian A; Mont, Michael A; McGrath, Mike S; Boyd, Bradley; Mitrick, Michael F

2009-12-01

New technology using magnetic resonance imaging (MRI) allows the surgeon to place total knee replacement components into each patient's pre-arthritic natural alignment. This study evaluated the initial intra-operative experience using this technique. Twenty-one patients had a sagittal MRI of their arthritic knee to determine component placement for a total knee replacement. Cutting guides were machined to control all intra-operative cuts. Intra-operative events were recorded and these knees were compared to a matching cohort of the senior surgeon's previous 30 conventional total knee replacements. Post-operative scanograms were obtained from each patient and coronal alignment was compared to previous studies using conventional and computer-assisted techniques. There were no intra-operative or acute post-operative complications. There were no differences in blood loss and there was a mean decrease in operative time of 14% compared to a cohort of patients with conventional knee replacements. The average deviation from the mechanical axis was 1.2 degrees of varus, which was comparable to previously reported conventional and computer-assisted techniques. Custom-fit total knee replacement appeared to be a safe procedure for uncomplicated cases of osteoarthritis.

One dimensional shock Initiation of UK Comp B

NASA Astrophysics Data System (ADS)

Burns, Malcolm

2017-06-01

Ten shock initiation experiments have been carried out on the UK isostatically pressed Composition B (59.5% RDX, 39.5% TNT, 1% wax) comprising of seven sustained pulse experiments with input pressures ranging from 2.89 to 9.86 GPa and three short shock experiments using the embedded gauge technique at the Los Alamos National Laboratory gas gun facility. The evolution of the reactive growth at and behind the shock front has been measured along with the run to detonation distance. These data have been used to create the Pop plot and hugoniot states for the UK Comp B. The shock initiation behavior of the UK Comp B has been compared to that of the equivalent US Composition. The reactive growth shows a feature that was observed in the US composition in which the wave profiles dispay a high level of pre-detonation noise. This was hypothesized to be due to a piezoelectric effect in the RDX crystals. The results of these experiments have shown that this effect may be localized in the gamma phase at shock pressures in the region of 5 GP and above.

ISMIP6 - initMIP: Greenland ice sheet model initialisation experiments

NASA Astrophysics Data System (ADS)

Goelzer, Heiko; Nowicki, Sophie; Payne, Tony; Larour, Eric; Abe Ouchi, Ayako; Gregory, Jonathan; Lipscomb, William; Seroussi, Helene; Shepherd, Andrew; Edwards, Tamsin

2016-04-01

Earlier large-scale Greenland ice sheet sea-level projections e.g. those run during ice2sea and SeaRISE initiatives have shown that ice sheet initialisation can have a large effect on the projections and gives rise to important uncertainties. This intercomparison exercise (initMIP) aims at comparing, evaluating and improving the initialization techniques used in the ice sheet modeling community and to estimate the associated uncertainties. It is the first in a series of ice sheet model intercomparison activities within ISMIP6 (Ice Sheet Model Intercomparison Project for CMIP6). The experiments are conceived for the large-scale Greenland ice sheet and are designed to allow intercomparison between participating models of 1) the initial present-day state of the ice sheet and 2) the response in two schematic forward experiments. The latter experiments serve to evaluate the initialisation in terms of model drift (forward run without any forcing) and response to a large perturbation (prescribed surface mass balance anomaly). We present and discuss first results of the intercomparison and highlight important uncertainties with respect to projections of the Greenland ice sheet sea-level contribution.

Quenching behavior of molten pool with different strategies – A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shrikant,, E-mail: 2014rmt9018@mnit.ac.in; Pandel, U.; Duchaniya, R. K.

After the major severe accident in nuclear reactor, there has been lot of concerns regarding long term core melt stabilization following a severe accident in nuclear reactors. Numerous strategies have been though for quenching and stabilization of core melt like top flooding, bottom flooding, indirect cooling, etc. However, the effectiveness of these schemes is yet to be determined properly, for which, lot of experiments are needed. Several experiments have been performed for coolability of melt pool under bottom flooding as well as for indirect cooling. Besides these tests are very scattered because they involve different simulants material initial temperatures andmore » masses of melt, which makes it very complex to judge the effectiveness of a particular technique and advantage over the other. In this review paper, a study has been carried on different cooling techniques of simulant materials with same mass. Three techniques have been compared here and the results are discussed. Under top flooding technique it took several hours to cool the melt under without decay heat condition. In bottom flooding technique was found to be the best technique among in indirect cooling technique, top flooded technique, and bottom flooded technique.« less

Experiments in free shear flows: Status and needs for the future

NASA Technical Reports Server (NTRS)

Kline, S. J.; Coles, D. E.; Eggers, J. M.; Harsha, P. T.

1973-01-01

Experiments in free turbulent flows are recommended with the primary concern placed on classical flows in order to augment understanding and for model building. Five classes of experiments dealing with classical free turbulent flows are outlined and proposed as being of particular significance for the near future. These classes include the following: (1) Experiments clarifying the effect of density variation owing to use of different gases, with and without the additional effect of density variation due to high Mach number or other effects; (2) experiments clarifying the role and importance of various parameters which determine the behavior of the near field as well as the condictions under which any of these parameters can be neglected; (3) experiments determining the cumulative effect of initial conditions in terms of distance to fully established flow; (4) experiments for cases where two layers of distinctly different initial turbulence structure flow side by side at the same mean speed; and (5) experiment using contemporary experimental techniques to study structure in free turbulent shear flows in order to compliment and support contemporary work on boundary layers.

Magnetic Control of Concentration Gradient in Microgravity

NASA Technical Reports Server (NTRS)

Leslie, Fred; Ramachandran, Narayanan

2005-01-01

A report describes a technique for rapidly establishing a fluid-concentration gradient that can serve as an initial condition for an experiment on solutal instabilities associated with crystal growth in microgravity. The technique involves exploitation of the slight attractive or repulsive forces exerted on most fluids by a magnetic-field gradient. Although small, these forces can dominate in microgravity and therefore can be used to hold fluids in position in preparation for an experiment. The magnetic field is applied to a test cell, while a fluid mixture containing a concentration gradient is prepared by introducing an undiluted solution into a diluting solution in a mixing chamber. The test cell is then filled with the fluid mixture. Given the magnetic susceptibilities of the undiluted and diluting solutions, the magnetic-field gradient must be large enough that the magnetic force exceeds both (1) forces associated with the flow of the fluid mixture during filling of the test cell and (2) forces imposed by any residual gravitation and fluctuations thereof. Once the test cell has been filled with the fluid mixture, the magnetic field is switched off so that the experiment can proceed, starting from the proper initial conditions.

Dating violence and girls in the juvenile justice system.

PubMed

Kelly, Patricia J; Cheng, An-Lin; Peralez-Dieckmann, Esther; Martinez, Elisabeth

2009-09-01

The purpose of this study is to explore the prevalence and associated behaviors of dating violence among a population of girls in the juvenile justice system. A sample of 590 girls from an urban juvenile justice system completed a questionnaire assessing attitudes and self-efficacy about and occurrence of dating violence. The analysis developed a random effect model to determine a risk profile for dating violence. The strongest predictors of dating violence were (a) initial sexual experience at age 13 or earlier, (b) unwillingness of initial sexual experience, (c) drug use, and (d) low self-efficacy about preventing dating violence. The high prevalence of dating violence and associated behaviors among participants suggests the importance of implementing primary prevention programs to assist preteen girls in delaying initial sexual intercourse and in learning techniques to prevent dating violence.

Atlas-based fuzzy connectedness segmentation and intensity nonuniformity correction applied to brain MRI.

PubMed

Zhou, Yongxin; Bai, Jing

2007-01-01

A framework that combines atlas registration, fuzzy connectedness (FC) segmentation, and parametric bias field correction (PABIC) is proposed for the automatic segmentation of brain magnetic resonance imaging (MRI). First, the atlas is registered onto the MRI to initialize the following FC segmentation. Original techniques are proposed to estimate necessary initial parameters of FC segmentation. Further, the result of the FC segmentation is utilized to initialize a following PABIC algorithm. Finally, we re-apply the FC technique on the PABIC corrected MRI to get the final segmentation. Thus, we avoid expert human intervention and provide a fully automatic method for brain MRI segmentation. Experiments on both simulated and real MRI images demonstrate the validity of the method, as well as the limitation of the method. Being a fully automatic method, it is expected to find wide applications, such as three-dimensional visualization, radiation therapy planning, and medical database construction.

Magnetic gauge instrumentation on the LANL gas-driven two-stage gun

NASA Astrophysics Data System (ADS)

Alcon, R. R.; Sheffield, S. A.; Martinez, A. R.; Gustavsen, R. L.

1998-07-01

The LANL gas-driven two-stage gun was designed and built to do initiation studies on insensitive high explosives as well as equation of state and reaction experiments on other materials. The preferred method of measuring reaction phenomena involves the use of in-situ magnetic particle velocity gauges. In order to accommodate this type of gauging in our two-stage gun, it has a 50-mm-diameter launch tube. We have used magnetic gauging on our 72-mm bore diameter single-stage gun for over 15 years and it has proven a very effective technique for all types of shock wave experiments, including those on high explosives. This technique has now been installed on our gas-driven two-stage gun. We describe the method used, as well as some of the difficulties that arose during the installation. Several magnetic gauge experiments have been completed on plastic materials. Waveforms obtained in some of the experiments will be discussed. Up to 10 in-situ particle velocity measurements can be made in a single experiment. This new technique is now working quite well, as is evidenced by the data. To our knowledge, this is the first time magnetic gauging has been used on a two-stage gun.

Elimination of Redwater Formation from TNT Manufacture

DTIC Science & Technology

2007-12-21

I TNT) or 80.4oC for Type II [11]. Further studies made after 1980 where novel reagents and modified techniques were employed are now summarized...compound, based on the oxidation of N2O4 using ozone [71-73], or electrolytic methods [74-76]. QinetiQ has also addressed aspects of the economics of...that can be utilized in the design of pilot plant and as a screening technique for suitability of continuous processing. The initial experiment was

Combined robotic transanal total mesorectal excision (R-taTME) and single-site plus one-port (R-SSPO) technique for ultra-low rectal surgery-initial experience with a new operation approach.

PubMed

Kuo, Li-Jen; Ngu, James Chi-Yong; Tong, Yiu-Shun; Chen, Chia-Che

2017-02-01

Robot-assisted rectal surgery is gaining popularity, and robotic single-site surgery is also being explored clinically. We report our initial experience with robotic transanal total mesorectal excision (R-taTME) and radical proctectomy using the robotic single-site plus one-port (R-SSPO) technique for low rectal surgery. Between July 2015 and March 2016, 15 consecutive patients with ultra-low rectal lesions underwent R-taTME followed by radical proctectomy using the R-SSPO technique by a single surgeon. The clinical and pathological results were retrospectively analyzed. The median operative time was 473 (range, 335-569) min, and the estimated blood loss was 33 (range, 30-50) mL. The median number of lymph nodes harvested was 12 (range, 8-18). The median distal resection margin was 1.4 (range, 0.4-3.5) cm, and all patients had clear circumferential resection margins. We encountered a left ureteric transection intraoperatively in one patient, and another patient required reoperation for postoperative adhesive intestinal obstruction. There was no 30-day mortality. R-taTME followed by radical proctectomy using the R-SSPO technique for patients with low rectal lesions is technically feasible and safe without compromising oncologic outcomes. However, there were considerable limitations and a steep learning curve using current robotic technology.

Use of indocyanine green angiography in microsurgical subinguinal varicocelectomy - lessons learned from our initial experience.

PubMed

Cho, Chak-Lam; Ho, Kwan-Lun; Chan, Wayne Kwun-Wai; Chu, Ringo Wing-Hong; Law, In-Chak

2017-01-01

Microsurgical subinguinal varicocelectomy (MSV) is generally considered the gold standard nowadays in view of the lower risk of complications and recurrence. To achieve complete ligation of veins while preserving testicular artery (TA) during the procedure remains challenging despite the application of high power optical magnification and micro-Doppler ultrasonography. The use of intraoperative indocyanine green angiography (ICGA) with infrared fluorescence operative micro-scope in MSV potentially lowers the incidence of TA injury and shortens the learning curve of nov-ice surgeons. We present our initial experience in the application of the technique in nine patients and explore the potential of the new adjunct. Copyright® by the International Brazilian Journal of Urology.

Minimal access surgery of pediatric inguinal hernias: a review.

PubMed

Saranga Bharathi, Ramanathan; Arora, Manu; Baskaran, Vasudevan

2008-08-01

Inguinal hernia is a common problem among children, and herniotomy has been its standard of care. Laparoscopy, which gained a toehold initially in the management of pediatric inguinal hernia (PIH), has managed to steer world opinion against routine contralateral groin exploration by precise detection of contralateral patencies. Besides detection, its ability to repair simultaneously all forms of inguinal hernias (indirect, direct, combined, recurrent, and incarcerated) together with contralateral patencies has cemented its role as a viable alternative to conventional repair. Numerous minimally invasive techniques for addressing PIH have mushroomed in the past two decades. These techniques vary considerably in their approaches to the internal ring (intraperitoneal, extraperitoneal), use of ports (three, two, one), endoscopic instruments (two, one, or none), sutures (absorbable, nonabsorbable), and techniques of knotting (intracorporeal, extracorporeal). In addition to the surgeons' experience and the merits/limitations of individual techniques, it is the nature of the defect that should govern the choice of technique. The emerging techniques show a trend toward increasing use of extracorporeal knotting and diminishing use of working ports and endoscopic instruments. These favor wider adoption of minimal access surgery in addressing PIH by surgeons, irrespective of their laparoscopic skills and experience. Growing experience, wider adoption, decreasing complications, and increasing advantages favor emergence of minimal access surgery as the gold standard for the treatment of PIH in the future. This article comprehensively reviews the laparoscopic techniques of addressing PIH.

Dynamic stability and handling qualities tests on a highly augmented, statically unstable airplane

NASA Technical Reports Server (NTRS)

Gera, Joseph; Bosworth, John T.

1987-01-01

Initial envelope clearance and subsequent flight testing of a new, fully augmented airplane with an extremely high degree of static instability can place unusual demands on the flight test approach. Previous flight test experience with these kinds of airplanes is very limited or nonexistent. The safe and efficient flight testing may be further complicated by a multiplicity of control effectors that may be present on this class of airplanes. This paper describes some novel flight test and analysis techniques in the flight dynamics and handling qualities area. These techniques were utilized during the initial flight envelope clearance of the X-29A aircraft and were largely responsible for the completion of the flight controls clearance program without any incidents or significant delays.

Environmental Sustainability Change Management in SMEs: Learning from Sustainability Champions

ERIC Educational Resources Information Center

Chadee, Doren; Wiesner, Retha; Roxas, Banjo

2011-01-01

This study identifies the change management processes involved in undertaking environmental sustainability (ES) initiatives within Small and Medium Size Enterprises (SMEs) and relate these to the main attributes of learning organisations. Using case study techniques, the study draws from the change management experiences of a sample of 12 ES…

Simultaneous Kidney-Pancreas Transplantation With an Original "Transverse Pancreas" Technique: Initial 9 Years' Experience With 56 Cases.

PubMed

Paulino, J; Martins, A; Vigia, E; Marcelino, P; Nobre, A M; Bicho, L; Filipe, E; Barroso, E

2017-10-01

An innovative technique for pancreas transplantation is described. The main aspect consists of the horizontal positioning of the pancreas, which allows a better venous outflow, thus preventing thrombosis and graft loss. The program of pancreas transplantation in this national reference center for pancreatic and liver surgery was started in 2007; the initial results were considered poor, resulting in the loss of half of the grafts due to venous thrombosis. After analyzing the possible causes, this technique was proposed and successfully implemented, reducing the postoperative complications, particularly the problem of venous thrombosis. A detailed description of the new surgical technique is provided. The main clinical and demographic characteristics of the 56 patients who underwent the surgery are analyzed. The incidence of venous thrombosis was 5.3% (3 patients) and graft loss was 3.5% (2 patients). Due to the good results, this technique became the standard surgery for transplantation of the pancreas in our center. The technique proved to be safe and successful. Due to the unique pancreas graft implantation, we called it "transverse pancreas surgery." Copyright © 2017 Elsevier Inc. All rights reserved.

Experimental analysis of quasi-static and dynamic fracture initiation toughness of gy4 armor steel material

NASA Astrophysics Data System (ADS)

Ren, Peng; Guo, Zitao

Quasi-static and dynamic fracture initiation toughness of gy4 armour steel material are investigated using three point bend specimen. The modified split Hopkinson pressure bar (SHPB) apparatus with digital image correlation (DIC) system is applied to dynamic loading experiments. Full-field deformation measurements are obtained by using DIC to elucidate on the strain fields associated with the mechanical response. A series of experiments are conducted at different strain rate ranging from 10-3 s-1 to 103 s-1, and the loading rate on the fracture initiation toughness is investigated. Specially, the scanning electron microscope imaging technique is used to investigate the fracture failure micromechanism of fracture surfaces. The gy4 armour steel material fracture toughness is found to be sensitive to strain rate and higher for dynamic loading as compared to quasi-static loading. This work is supported by National Nature Science Foundation under Grant 51509115.

Anaesthetic management for awake craniotomy in brain glioma resection: initial experience in Military Hospital Mohamed V of Rabat.

PubMed

Meziane, Mohammed; Elkoundi, Abdelghafour; Ahtil, Redouane; Guazaz, Miloudi; Mustapha, Bensghir; Haimeur, Charki

2017-01-01

The awake brain surgery is an innovative approach in the treatment of tumors in the functional areas of the brain. There are various anesthetic techniques for awake craniotomy (AC), including asleep-awake-asleep technique, monitored anesthesia care, and the recent introduced awake-awake-awake method. We describe our first experience with anesthetic management for awake craniotomy, which was a combination of these techniques with scalp nerve block, and propofol/rémifentanil target controlled infusion. A 28-year-oldmale underwent an awake craniotomy for brain glioma resection. The scalp nerve block was performed and a low sedative state was maintained until removal of bone flap. During brain glioma resection, the patient awake state was maintained without any complications. Once, the tumorectomy was completed, the level of anesthesia was deepened and a laryngeal mask airway was inserted. A well psychological preparation, a reasonable choice of anesthetic techniques and agents, and continuous team communication were some of the key challenges for successful outcome in our patient.

Initial development of an NIR strain measurement technique in brittle geo-materials

NASA Astrophysics Data System (ADS)

Butcher, Emily; Gibson, Andrew; Benson, Philip

2016-04-01

Visible-Near Infrared Spectroscopy (VIS-NIR) is a technique developed for the non-contact measurement of compositional characteristics of surfaces. The technique is rapid, sensitive to change in surface topology and has found applications ranging from planetary geology, soil science, pharmacy to materials testing. The technique has also been used in a limited fashion to measure strain changes in rocks and minerals (Ord and Hobbs 1986). However, there have been few quantitative studies linking such changes in material strains (and other rock physics parameters) to the resulting VIS-NIT signature. This research seeks to determine whether improvements in VIS-NIR equipment means that such a technique is a viable method to measure strains in rock via this remote (non-contact) method. We report new experiments carried out using 40 mm Brazilian Tensile discs of Carrera Marble and Darley Dale Sandstone using an Instron 600LX in the University of Portsmouth Rock Mechanics Laboratory. The tensile test was selected for this experiment as the sample shape and sensor arrangements allow access to a 'flat' surface area throughout the test, allowing surface measurements to be continuously taken whilst the discs are strained to failure. An ASD Labspec 5000 with 25 mm foreoptic was used to collect reflectance spectra in the range 350-2500 nm during each tensile test. Results from Carrera Marble experiments show that reflectance at 2050 nm negatively correlates (by polynomial regression) with axial strain between 0.05-0.5%, with r2 of 0.99. Results from Darley Dale Sandstone data show that reflectance at 1970 nm positively correlates with axial deformation between 0.05-0.5%, with r2 of 0.98. Initial analyses suggests that the VIS-NIR possesses an output that scales in a quantifiable manner with rock strain, and shows promise as a technique for strain measurement. The method has particular application for allowing our laboratory measurements to "ground truth" data taken from drone and other remote sensing techniques that could employ this method. However, further work is underway to understand the exact nature of the correlations - for instance, whether reflectance is related to deformation to the mineral lattice, macro-surface or micro-surface.

Case studies from Oman for coiled tubing deployed completion techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, R.W.; Conrad, B.

1996-09-01

Although the use of ultra-large coiled tubing to complete wells is relatively new, it is gaining widespread industry application. This paper will detail the equipment necessary to perform an operation of this type and will present information from several case studies in Oman in which an operator has successfully deployed completion equipment on 3-1/2-inch-OD coiled tubing. In addition to a discussion of the equipment required to perform the necessary operations, the trial parameters that were established by this operator will be given. The information presented has been selected to allow an initial evaluation to be made of coiled tubing completionsmore » in general and will help to determine whether this method can prove to be less expensive than traditional rig-based completions. The topics presented have been chosen to provide the reader with a thorough understanding of the techniques and preparation needed to execute a coiled tubing completion. The summary of experiences will conclude that this innovative completion technique can be a viable method for completing wells. Although long-term advantages regarding production and well maintenance cannot yet be determined, the operator`s experiences to date have confirmed his initial belief that use of coiled tubing in ultra-large continuous-pipe applications can be cost effective.« less

Laboratory hydraulic fracturing experiments in intact and pre-fractured rock

USGS Publications Warehouse

Zoback, M.D.; Rummel, F.; Jung, R.; Raleigh, C.B.

1977-01-01

Laboratory hydraulic fracturing experiments were conducted to investigate two factors which could influence the use of the hydrofrac technique for in-situ stress determinations; the possible dependence of the breakdown pressure upon the rate of borehole pressurization, and the influence of pre-existing cracks on the orientation of generated fractures. The experiments have shown that while the rate of borehole pressurization has a marked effect on breakdown pressures, the pressure at which hydraulic fractures initiate (and thus tensile strength) is independent of the rate of borehole pressurization when the effect of fluid penetration is negligible. Thus, the experiments indicate that use of breakdown pressures rather than fracture initiation pressures may lead to an erroneous estimate of tectonic stresses. A conceptual model is proposed to explain anomalously high breakdown pressures observed when fracturing with high viscosity fluids. In this model, initial fracture propagation is presumed to be stable due to large differences between the borehole pressure and that within the fracture. In samples which contained pre-existing fractures which were 'leaky' to water, we found it possible to generate hydraulic fractures oriented parallel to the direction of maximum compression if high viscosity drilling mud was used as the fracturing fluid. ?? 1977.

Experimental Measurements of the Chemical Reaction Zone of Detonating Liquid Explosives

NASA Astrophysics Data System (ADS)

Bouyer, Viviane; Sheffield, Stephen A.; Dattelbaum, Dana M.; Gustavsen, Richard L.; Stahl, David B.; Doucet, Michel; Decaris, Lionel

2009-12-01

We have a joint project between CEA-DAM Le Ripault and Los Alamos National Laboratory (LANL) to study the chemical reaction zone in detonating high explosives using several different laser velocimetry techniques. The short temporal duration of the von Neumann spike and early part of the reaction zone make these measurements difficult. Here, we report results obtained from detonation experiments using VISAR (velocity interferometer system for any reflector) and PDV (photon Doppler velocimetry) methods to measure the particle velocity history at a detonating nitromethane/PMMA interface. Experiments done at CEA were high-explosive-plane-wave initiated and those at LANL were gas-gun-projectile initiated with a detonation run of about 6 charge diameters in all experiments. The experiments had either glass or brass confinement. Excellent agreement of the interface particle velocity measurements at both Laboratories were obtained even though the initiation methods and the velocimetry systems were somewhat different. Some differences were observed in the peak particle velocity because of the ˜2 ns time resolution of the techniques—in all cases the peak was lower than the expected von Neumann spike. This is thought to be because the measurements were not high enough time resolution to resolve the spike.

Results of the Greenland Ice Sheet Model Initialisation Experiments ISMIP6 - initMIP-Greenland

NASA Astrophysics Data System (ADS)

Goelzer, H.; Nowicki, S.; Edwards, T.; Beckley, M.; Abe-Ouchi, A.; Aschwanden, A.; Calov, R.; Gagliardini, O.; Gillet-chaulet, F.; Golledge, N. R.; Gregory, J. M.; Greve, R.; Humbert, A.; Huybrechts, P.; Larour, E. Y.; Lipscomb, W. H.; Le ´h, S.; Lee, V.; Kennedy, J. H.; Pattyn, F.; Payne, A. J.; Rodehacke, C. B.; Rückamp, M.; Saito, F.; Schlegel, N.; Seroussi, H. L.; Shepherd, A.; Sun, S.; Vandewal, R.; Ziemen, F. A.

2016-12-01

Earlier large-scale Greenland ice sheet sea-level projections e.g. those run during ice2sea and SeaRISE initiatives have shown that ice sheet initialisation can have a large effect on the projections and gives rise to important uncertainties. The goal of this intercomparison exercise (initMIP-Greenland) is to compare, evaluate and improve the initialization techniques used in the ice sheet modeling community and to estimate the associated uncertainties. It is the first in a series of ice sheet model intercomparison activities within ISMIP6 (Ice Sheet Model Intercomparison Project for CMIP6). Two experiments for the large-scale Greenland ice sheet have been designed to allow intercomparison between participating models of 1) the initial present-day state of the ice sheet and 2) the response in two schematic forward experiments. The forward experiments serve to evaluate the initialisation in terms of model drift (forward run without any forcing) and response to a large perturbation (prescribed surface mass balance anomaly). We present and discuss final results of the intercomparison and highlight important uncertainties with respect to projections of the Greenland ice sheet sea-level contribution.

Experience with the Nuss technique for the treatment of Pectus Excavatum in Spanish Thoracic Surgery Departments.

PubMed

Fibla, Juan J; Molins, Laureano; Moradiellos, Javier; Rodríguez, Pedro; Heras, Félix; Canalis, Emili; Bolufer, Sergio; Martínez, Pablo; Aragón, Javier; Arroyo, Andrés; Pérez, Javier; León, Pablo; Canela, Mercedes

2016-01-01

Although the Nuss technique revolutionized the surgical treatment of pectus excavatum, its use has not become widespread in our country. The aim of this study was to analyze the current use of this technique in a sample of Thoracic Surgery Departments in Spain. Observational rectrospective multicentric study analyzing the main epidemiological aspects and clinical results of ten years experience using the Nuss technique. Between 2001 and 2010 a total of 149 patients were operated on (mean age 21.2 years), 74% male. Initial aesthetic results were excellent or good in 93.2%, mild in 4.1% and bad in 2.7%. After initial surgery there were complications in 45 patients (30.6%). The most frequent were wound seroma, bar displacement, stabilizer break, pneumothorax, haemothorax, wound infection, pneumonia, pericarditis and cardiac tamponade that required urgent bar removal. Postoperative pain appeared in all patients. In 3 cases (2%) it was so intense that it required bar removal. After a mean follow-up of 39.2 months, bar removal had been performed in 72 patients (49%), being difficult in 5 cases (7%). After a 1.6 year follow-up period good results persisted in 145 patients (98.7%). Nuss technique in adults has had good results in Spanish Thoracic Surgery Departments, however its use has not been generalized. The risk of complications must be taken into account and its indication must be properly evaluated. The possibility of previous conservative treatment is being analyzed in several departments at present. Copyright © 2015 AEC. Publicado por Elsevier España, S.L.U. All rights reserved.

Technique for fabrication of ultrathin foils in cylindrical geometry for liner-plasma implosion experiments with sub-megaampere currents

DOE PAGES

Yager-Elorriaga, D. A.; Steiner, A. M.; Patel, S. G.; ...

2015-11-19

In this study, we describe a technique for fabricating ultrathin foils in cylindrical geometry for liner-plasma implosion experiments using sub-MA currents. Liners are formed by wrapping a 400 nm, rectangular strip of aluminum foil around a dumbbell-shaped support structure with a non-conducting center rod, so that the liner dimensions are 1 cm in height, 6.55 mm in diameter, and 400 nm in thickness. The liner-plasmas are imploded by discharging ~600 kA with ~200 ns rise time using a 1 MA linear transformer driver, and the resulting implosions are imaged four times per shot using laser-shadowgraphy at 532 nm. As amore » result, this technique enables the study of plasma implosion physics, including the magneto Rayleigh-Taylor, sausage, and kink instabilities on initially solid, imploding metallic liners with university-scale pulsed power machines.« less

Simple electrical model and initial experiments for intra-body communications.

PubMed

Gao, Y M; Pun, S H; Du, M; Mak, P U; Vai, M I

2009-01-01

Intra-Body Communication(IBC) is a short range "wireless" communication technique appeared in recent years. This technique relies on the conductive property of human tissue to transmit the electric signal among human body. This is beneficial for devices networking and sensors among human body, and especially suitable for wearable sensors, telemedicine system and home health care system as in general the data rates of physiologic parameters are low. In this article, galvanic coupling type IBC application on human limb was investigated in both its mathematical model and related experiments. The experimental results showed that the proposed mathematical model was capable in describing the galvanic coupling type IBC under low frequency. Additionally, the calculated result and experimental result also indicated that the electric signal induced by the transmitters of IBC can penetrate deep into human muscle and thus, provide an evident that IBC is capable of acting as networking technique for implantable devices.

Technique for fabrication of ultrathin foils in cylindrical geometry for liner-plasma implosion experiments with sub-megaampere currents

NASA Astrophysics Data System (ADS)

Yager-Elorriaga, D. A.; Steiner, A. M.; Patel, S. G.; Jordan, N. M.; Lau, Y. Y.; Gilgenbach, R. M.

2015-11-01

In this work, we describe a technique for fabricating ultrathin foils in cylindrical geometry for liner-plasma implosion experiments using sub-MA currents. Liners are formed by wrapping a 400 nm, rectangular strip of aluminum foil around a dumbbell-shaped support structure with a non-conducting center rod, so that the liner dimensions are 1 cm in height, 6.55 mm in diameter, and 400 nm in thickness. The liner-plasmas are imploded by discharging ˜600 kA with ˜200 ns rise time using a 1 MA linear transformer driver, and the resulting implosions are imaged four times per shot using laser-shadowgraphy at 532 nm. This technique enables the study of plasma implosion physics, including the magneto Rayleigh-Taylor, sausage, and kink instabilities on initially solid, imploding metallic liners with university-scale pulsed power machines.

Technique for fabrication of ultrathin foils in cylindrical geometry for liner-plasma implosion experiments with sub-megaampere currents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yager-Elorriaga, D. A.; Steiner, A. M.; Patel, S. G.

In this study, we describe a technique for fabricating ultrathin foils in cylindrical geometry for liner-plasma implosion experiments using sub-MA currents. Liners are formed by wrapping a 400 nm, rectangular strip of aluminum foil around a dumbbell-shaped support structure with a non-conducting center rod, so that the liner dimensions are 1 cm in height, 6.55 mm in diameter, and 400 nm in thickness. The liner-plasmas are imploded by discharging ~600 kA with ~200 ns rise time using a 1 MA linear transformer driver, and the resulting implosions are imaged four times per shot using laser-shadowgraphy at 532 nm. As amore » result, this technique enables the study of plasma implosion physics, including the magneto Rayleigh-Taylor, sausage, and kink instabilities on initially solid, imploding metallic liners with university-scale pulsed power machines.« less

The use of bioabsorbable staple line reinforcement for circular stapler (BSG "Seamguard") in colorectal surgery: initial experience.

PubMed

Franklin, Morris E; Ramila, Guillermo Portillo; Treviño, Jorge M; González, John J; Russek, Karla; Glass, Jeffrey L; Kim, Greg

2006-12-01

Of all the complications associated with colorectal surgery, the most devastating and constant, despite all techniques being performed properly is anastomotic leakage, especially in left colon and rectal resections with rates as high as 50% when the rectum is involved. In 2005, our center published the preliminary experience with the use of linear staple line reinforcement for colon surgery. The purpose of this paper is to present a series of cases using a new conformation of bioabsorbable reinforcement for circular staplers in 5 patients, 2 patients with rectal cancer, 2 patients with diverticular disease, and 1 patient with sigmoid cancer. These initial data are very promising and has encouraged us to continue using this device on further patients.

Embedded Librarianship and Teacher Education: A Neuroeducational Paradigm Using Guided Inquiry

ERIC Educational Resources Information Center

Warner, Signia; Templeton, Lolly

2010-01-01

This article focuses on a course-embedded guided inquiry project initiated by a senior librarian and an education professor to promote an understanding of how the brain functions and to experiment with brain-targeted teaching techniques. Information literacy instruction (ILI) takes place in the electronic classroom in the Educational Resources…

Chest Ultrasound Integrated Teaching of Respiratory System Physiology to Medical Students: A First Experience

ERIC Educational Resources Information Center

Paganini, M.; Rubini, A.

2015-01-01

Ultrasound imaging is a useful diagnostic technique that has spread among several different medical specialties within the last few years. Initially restricted to radiology, cardiology, obstetrics, and gynecology, today it is widely used by many specialists, especially in critical care. New graduate physicians will need to be comfortable with…

The Army Officer as Performance Manager. Professional Paper No. 13-74.

ERIC Educational Resources Information Center

Fry, John P.

This paper describes the results of one Army officer's experiment in applying the techniques of psychological research on the job. With a view to developing his subordinates' leadership ability and initiative, and permitting them an active role in managing the battalion, he emphasized particularly the principles of "contingency management"…

TITANIUM DIOXIDE AND ULTRA-VIOLET LIGHT: A SUSTAINABLE AND INEXPENSIVE SOLUTION FOR ADDRESSING DRINKING WATER QUALITY ISSUES IN THE DEVELOPING COUNTRIES

EPA Science Inventory

The Ti0₂ based purification system reactor was built and tested by various diagnostic techniques for its efficacy in detoxification of water against organic and biological matter. Initial experiments were done with ultraviolet lamp as ...

Endovascular balloon-assisted embolization of intracranial and cervical arteriovenous malformations using dual-lumen coaxial balloon microcatheters and Onyx: initial experience.

PubMed

Jagadeesan, Bharathi D; Grigoryan, Mikayel; Hassan, Ameer E; Grande, Andrew W; Tummala, Ramachandra P

2013-12-01

Ethylene vinyl alcohol copolymer (Onyx) is widely used for the embolization of arteriovenous malformations (AVMs) of the brain, head, and neck. Balloon-assisted Onyx embolization may provide additional unique advantages in the treatment of AVMs in comparison with traditional catheter-based techniques. To report our initial experience in performing balloon-assisted AVM embolization for brain and neck AVMs with the use of the new Scepter-C and Scepter-XC coaxial dual-lumen balloon microcatheters. Balloon-assisted transarterial embolization was performed in a series of 7 patients with AVMs (4 with brain AVMs, 1 with a dural arteriovenous fistula, and 2 with neck AVMs) by using Onyx delivered through the lumen of Scepter-C or Scepter XC coaxial balloon microcatheters. Following the initial balloon-catheter navigation into a feeding artery and the subsequent inflation of the balloon, the embolization was performed by using Onyx 18, Onyx 34, or both. A total of 12 embolization sessions were performed via 17 arterial feeders in these 7 patients. In 1 patient, there was an arterial perforation from the inflation of the balloon; in all others, the embolization goals were successfully achieved with no adverse events. The balloon microcatheters showed excellent navigability, and there were no problems with retrieval or with the repeated inflation and deflation of the balloons. A proximal Onyx plug, which is crucial in many AVM embolizations, was not necessary with this technique. Additionally, fluoroscopy and procedural times seemed lower with this technique compared with conventional embolization methods.

Rapid profiling of laser-induced photochemistry in single microdroplets using mass spectrometry.

PubMed

Tracey, Phillip J; Vaughn, Bartholomew S; Roberts, Brendon J; Poad, Berwyck L J; Trevitt, Adam J

2014-03-18

Rapid assessment of laser-induced photochemistry in single microdroplets is afforded by on-demand microdroplet generation coupled to a commercial ion-trap mass spectrometer. Single microdroplets (diameter ∼50 μm, 65 pL) fall on a steel needle held at +2 kV where they subsequently form a spray that is directed toward the inlet of an ion-trap mass spectrometer. It is demonstrated that single microdroplet mass spectra are recordable, one at a time, for methanol droplets containing 100 μM 4-iodoaniline. Extending on this, to probe laser-initiated photochemistry in single picoliter volumes, a UV laser pulse is timed to intercept the droplet before hitting the needle. Comparison of laser-on and laser-off mass spectra reveals the laser-initiated photochemical products. We demonstrate the technique by following UV laser initiated chemistry in methanol droplets containing 4-iodoaniline and 3-(iodomethyl)-N,N,N-trimethylbenzenamine and reveal numerous products within a few hundred single droplet experiments over several minutes. This technique allows for rapid detection of laser-initiated photochemistry in single picoliter volumes.

Hand-held microwave search detector

NASA Astrophysics Data System (ADS)

Daniels, David J.; Philippakis, Mike

2005-05-01

This paper describes the further development of a patented, novel, low cost, microwave search detector using noise radar technology operating in the 27-40GHz range of frequencies, initially reported in SPIE 2004. Initial experiments have shown that plastic explosives, ceramics and plastic material hidden on the body can be detected with the system. This paper considers the basic physics of the technique and reports on the development of a initial prototype system for hand search of suspects and addresses the work carried out on optimisation of PD and FAR. The radar uses a novel lens system and the design and modelling of this for optimum depth of field of focus will be reported.

From thermometric to spectrophotometric kinetic-catalytic methods of analysis. A review.

PubMed

Cerdà, Víctor; González, Alba; Danchana, Kaewta

2017-05-15

Kinetic-catalytic analytical methods have proved to be very easy and highly sensitive strategies for chemical analysis, that rely on simple instrumentation [1,2]. Molecular absorption spectrophotometry is commonly used as the detection technique. However, other detection systems, like electrochemical or thermometric ones, offer some interesting possibilities since they are not affected by the color or turbidity of the samples. In this review some initial experience with thermometric kinetic-catalytic methods is described, up to our current experience exploiting spectrophotometric flow techniques to automate this kind of reactions, including the use of integrated chips. Procedures for determination of inorganic and organic species in organic and inorganic matrices are presented. Copyright © 2017 Elsevier B.V. All rights reserved.

Early experience with high-flow nasal oxygen therapy (HFNOT) in pediatric endoscopic airway surgery.

PubMed

Riva, Thomas; Theiler, Lorenz; Jaquet, Yves; Giger, Roland; Nisa, Lluís

2018-05-01

Reporting our institutional experience with high-flow nasal oxygen therapy (HFNOT), a recently-introduced technique, for endoscopic airway approaches. Prospective collection of data of children (<16 years) undergoing endoscopic between January 2016 and August 2017 at a tertiary referral university hospital. HFNOT was used in 6 children who underwent 14 procedures for different forms and causes of upper airway obstruction of various origins. No intraoperative complications; related to oxygenation were observed, and the surgical procedures could be carried out as; initially planned. We found that HFNOT is an effective and safe technique with a variety of potential applications in the field of endoscopic pediatric airway surgery. Copyright © 2018 Elsevier B.V. All rights reserved.

Initial results on fault diagnosis of DSN antenna control assemblies using pattern recognition techniques

NASA Technical Reports Server (NTRS)

Smyth, P.; Mellstrom, J.

1990-01-01

Initial results obtained from an investigation using pattern recognition techniques for identifying fault modes in the Deep Space Network (DSN) 70 m antenna control loops are described. The overall background to the problem is described, the motivation and potential benefits of this approach are outlined. In particular, an experiment is described in which fault modes were introduced into a state-space simulation of the antenna control loops. By training a multilayer feed-forward neural network on the simulated sensor output, classification rates of over 95 percent were achieved with a false alarm rate of zero on unseen tests data. It concludes that although the neural classifier has certain practical limitations at present, it also has considerable potential for problems of this nature.

Ramp compression of a metallic liner driven by a shaped 5 MA current on the SPHINX machine

NASA Astrophysics Data System (ADS)

d'Almeida, T.; Lassalle, F.; Morell, A.; Grunenwald, J.; Zucchini, F.; Loyen, A.; Maysonnave, T.; Chuvatin, A.

2014-05-01

SPHINX is a 6MA, 1-us Linear Transformer Driver operated by the CEA Gramat (France) and primarily used for imploding Z-pinch loads for radiation effects studies. A method for performing magnetic ramp compression experiments was developed using a compact Dynamic Load Current Multiplier inserted between the convolute and the load, to shape the initial current pulse. We present the overall experimental configuration chosen for these experiments and initial results obtained over a set of experiments on an aluminum cylindrical liner. Current profiles measured at various critical locations across the system, are in good agreement with simulated current profiles. The liner inner free surface velocity measurements agree with the hydrocode results obtained using the measured load current as the input. The potential of the technique in terms of applications and achievable ramp pressure levels lies in the prospects for improving the DLCM efficiency.

Viewing-position effects in the Stroop task: Initial fixation position modulates Stroop effects in fully colored words.

PubMed

Perret, Patrick; Ducrot, Stéphanie

2010-08-01

In two experiments that we conducted with adult (Experiment 1) and child (Experiment 2) participants, we experimentally controlled the eyes' first fixation in the word using a variable viewing-position technique in a classical all-letter-coloring Stroop procedure. We explored the impact of initial-fixation position (optimal viewing position [OVP] vs. end of the word) on the magnitude of Stroop effects (both interference and facilitation). The results showed that both interference and facilitation effects were reduced when the first fixation was located at the end of the word rather than at the OVP. These data make a new contribution to the study of the role of low-level processes in Stroop effects and add support to the growing body of research indicating that oculomotor processes can act as moderators of cognitive processes in the determination of Stroop effects.

Alternate methodologies to experimentally investigate shock initiation properties of explosives

NASA Astrophysics Data System (ADS)

Svingala, Forrest R.; Lee, Richard J.; Sutherland, Gerrit T.; Benjamin, Richard; Boyle, Vincent; Sickels, William; Thompson, Ronnie; Samuels, Phillip J.; Wrobel, Erik; Cornell, Rodger

2017-01-01

Reactive flow models are desired for new explosive formulations early in the development stage. Traditionally, these models are parameterized by carefully-controlled 1-D shock experiments, including gas-gun testing with embedded gauges and wedge testing with explosive plane wave lenses (PWL). These experiments are easy to interpret due to their 1-D nature, but are expensive to perform and cannot be performed at all explosive test facilities. This work investigates alternative methods to probe shock-initiation behavior of new explosives using widely-available pentolite gap test donors and simple time-of-arrival type diagnostics. These experiments can be performed at a low cost at most explosives testing facilities. This allows experimental data to parameterize reactive flow models to be collected much earlier in the development of an explosive formulation. However, the fundamentally 2-D nature of these tests may increase the modeling burden in parameterizing these models and reduce general applicability. Several variations of the so-called modified gap test were investigated and evaluated for suitability as an alternative to established 1-D gas gun and PWL techniques. At least partial agreement with 1-D test methods was observed for the explosives tested, and future work is planned to scope the applicability and limitations of these experimental techniques.

Birth and initial developments of experiments with resonant detectors searching for gravitational waves

NASA Astrophysics Data System (ADS)

Pizzella, G.

2016-12-01

A history of the experiments for the search of gravitational waves, with emphasis on the experiments made by the Rome group, is given. The search for gravitational waves was initiated by the brilliant scientific acumen of Joseph Weber. In this paper we start from the early times of the resonant detectors at room temperature and continue with the cryogenic resonant detectors: STANFORD, ALLEGRO, AURIGA, EXPLORER, NAUTILUS and NIOBE. These cryogenic detectors reached a sensitivity able to observe gravitational waves generated by the conversion of about 0.001 solar masses in the Galaxy. This was an improvement by a factor of a few thousand in energy with respect to the early room temperature experiments. No clear signals due to gravitational waves have been observed with this technique. This research, that has lasted four decades, has paved the way to the more sensitive detectors for gravitational waves, the long-arm laser interferometers, which announced, on February 12th 2016, the first observation of gravitational waves.

Topology-optimized metasurfaces: impact of initial geometric layout.

PubMed

Yang, Jianji; Fan, Jonathan A

2017-08-15

Topology optimization is a powerful iterative inverse design technique in metasurface engineering and can transform an initial layout into a high-performance device. With this method, devices are optimized within a local design phase space, making the identification of suitable initial geometries essential. In this Letter, we examine the impact of initial geometric layout on the performance of large-angle (75 deg) topology-optimized metagrating deflectors. We find that when conventional metasurface designs based on dielectric nanoposts are used as initial layouts for topology optimization, the final devices have efficiencies around 65%. In contrast, when random initial layouts are used, the final devices have ultra-high efficiencies that can reach 94%. Our numerical experiments suggest that device topologies based on conventional metasurface designs may not be suitable to produce ultra-high-efficiency, large-angle metasurfaces. Rather, initial geometric layouts with non-trivial topologies and shapes are required.

Microscale and nanoscale strain mapping techniques applied to creep of rocks

NASA Astrophysics Data System (ADS)

Quintanilla-Terminel, Alejandra; Zimmerman, Mark E.; Evans, Brian; Kohlstedt, David L.

2017-07-01

Usually several deformation mechanisms interact to accommodate plastic deformation. Quantifying the contribution of each to the total strain is necessary to bridge the gaps from observations of microstructures, to geomechanical descriptions, to extrapolating from laboratory data to field observations. Here, we describe the experimental and computational techniques involved in microscale strain mapping (MSSM), which allows strain produced during high-pressure, high-temperature deformation experiments to be tracked with high resolution. MSSM relies on the analysis of the relative displacement of initially regularly spaced markers after deformation. We present two lithography techniques used to pattern rock substrates at different scales: photolithography and electron-beam lithography. Further, we discuss the challenges of applying the MSSM technique to samples used in high-temperature and high-pressure experiments. We applied the MSSM technique to a study of strain partitioning during creep of Carrara marble and grain boundary sliding in San Carlos olivine, synthetic forsterite, and Solnhofen limestone at a confining pressure, Pc, of 300 MPa and homologous temperatures, T/Tm, of 0.3 to 0.6. The MSSM technique works very well up to temperatures of 700 °C. The experimental developments described here show promising results for higher-temperature applications.

Biliary access in technically difficult biliary cannulation: the mucosal bridge technique

PubMed Central

Thomas, Rebecca; Shah, Suhaila Rizal; Worthley, Christopher S

2009-01-01

Background: The use of precut sphincterotomy during endoscopic retrograde cholangiopancreatography (ERCP) facilitates selective bile duct access in difficult procedures. However, it is also associated with high rates of complications. Several techniques for precut sphincterotomy have been described in the literature. This paper reports our experience with a non-needle-knife technique for precut sphincterotomy, namely, the mucosal bridge technique. Methods: We analysed the experience of a single surgical endoscopist at our centre in performing precut sphincterotomies by retrospectively examining information in the database for January 2002 to February 2008, which had been stored prospectively using Endoscribe. Results: The mucosal bridge technique was performed in 16 (3.19%) of 501 patients. Success rates were 75% and 100% after first and second ERCPs, respectively. The failure of initial procedures was caused by bleeding, tissue oedema, poorly visualized papilla or a poorly distensible duodenum and oedematous papilla. There were four cases of complications, which included periductular extravasation of contrast, bleeding, and sepsis in two patients. However, these complications were not a direct consequence of the precut sphincterotomy. Conclusions: The mucosal bridge technique can be used to increase the likelihood of successful bile duct cannulation, thus preventing the need for a second intervention. PMID:19590645

Videothoracoscopy in the treatment of spontaneous pneumothorax: an initial experience.

PubMed Central

Waller, D. A.; Yoruk, Y.; Morritt, G. N.; Forty, J.; Dark, J. H.

1993-01-01

We report an initial experience with the new and potentially advantageous technique of videothoracoscopy in the treatment of pneumothorax. A series of 18 consecutive patients (14 male, 4 female) presenting with spontaneous pneumothorax over a 4-month period underwent surgical treatment by this method. The indication for surgery was recurrent pneumothorax in nine patients and persistent air leak in the remainder (median duration 15 days, range 5-28 days). Stapled apical bullectomy with apical parietal pleurectomy was performed in 14 patients, bullectomy alone was performed in one patient and pleurectomy alone in three patients. Additional talc pleurodesis was carried out in three of these patients. Median duration of operation was 53.5 min (range 35-120 min). The median postoperative drainage was 300 ml in 24 h (range 50-580 ml). The median duration of intercostal drainage was 48 h (range 24-384 h) and of postoperative hospital stay 4 days (range 3-18 days). The mean postoperative analgesic requirement was 1.3 mg morphine/h. Three complications required reoperation. In two patients a large air leak persisted after operation; one proceeded to thoracotomy for suturing of the air leak and in the other this was accomplished by videothoracoscopy. A further patient re-presented at 2 weeks with recurrent pneumothorax which was treated at thoracotomy. At a median follow-up of 68.5 days (range 10-124 days) this is the only recurrence. These complications were caused by errors in surgical technique early in our series. This initial experience of videothoracoscopic pleurectomy suggests it is an effective, well-tolerated treatment of spontaneous pneumothorax. PMID:8379623

Managing Ventricular Septal Defect with Associated Aortic Regurgitation: Two Decades of Experience.

PubMed

Sanoussi, Ahmed; Demanet, Helene; Dessy, Hughes; Massin, Martial; Biarent, Dominique; Deville, Andree; Wauthy, Pierre

2015-09-01

Ventricular septal defect (VSD) with aortic regurgitation (AR) is a well-known association. However, there is still no agreement about its management, particularly regarding the technical details of its operative treatment. The study aim was to describe all components of the syndrome and to evaluate the various techniques used with regards to its anatomical and functional features. A total of 31 patients (mean age 7.4 years; range: 1.0-14.3 years) who underwent repair of VSD and AR between 1990 and 2013 was reviewed. The VSD was perimembranous in 22 patients, and subarterial in nine. Trusler's valvuloplasty technique was used in 15 patients, Yacoub's technique in seven, and Carpentier's technique (triangular resection) in four. Two patients underwent aortic valve replacement (AVR), and three patients with no significant aortic valve lesions underwent a simple patch repair of the VSD. The aortic valvuloplasty results were generally good, with an initial aortic valvuloplasty avoiding AVR. During the immediate postoperative period, valvuloplasty failure occurred in three patients, regardless of the technique used, and all three patients were reoperated on. The mean duration of follow up was 8.5 years (range: 3.2-20.6 years). The initial result was maintained in all patients, except for four who underwent late AVR. The study findings contributed to an analysis of VSD and AR, and helped to clarify the best surgical strategy. The results obtained suggest that adequacy of the initial repair is the most important determinant of subsequent evolution.

Robot-assisted intracorporeal ileal conduit: Marionette technique and initial experience at Roswell Park Cancer Institute.

PubMed

Guru, Khurshid; Seixas-Mikelus, Stéfanie A; Hussain, Abid; Blumenfeld, Aaron J; Nyquist, John; Chandrasekhar, Rameela; Wilding, Gregory E

2010-10-01

To present our technique and initial experience with patients who underwent robot-assisted intracorporeal creation of ileal conduit and to compare them with patients who underwent extracorporeal ileal diversion after robot-assisted radical cystectomy. Twenty-six patients diagnosed with invasive transitional cell carcinoma of the bladder underwent a robot-assisted radical cystectomy with bilateral extended pelvic lymphadenectomy with ileal conduit diversion. Total intracorporeal ileal conduit creation was performed in the last 13 patients. Operative data and short-term outcomes between the 2 groups were assessed. The novel surgical technique for intracorporeal ileal conduit will be presented. The intracorporeal group (IC) included 2 female and 11 male patients (mean age 71 years). The extracorporeal group (EC) included 4 female and 9 male patients (mean age 66 years). No significant differences were noted between the groups in terms of patient age, BMI, sex, prior surgery, or pathologic stage. Overall operative time and intraoperative complications were similar. No significant differences were noted between the 2 groups in terms of diversion time or estimated blood loss. There were 4 complications recorded in IC patients, including nonspecific colitis, small bowel obstruction requiring exploratory laparotomy with lysis of adhesions, a urine leak that eventually resolved but required a temporary nephrostomy tube, and a fever of unknown origin that resolved without intervention. Robot-assisted intracorporeal ileal conduit can be accomplished safely with acceptable operative times even during early experience. Larger series with favorable results will be required to add this new paradigm to minimally invasive surgery for bladder cancer. Copyright © 2010 Elsevier Inc. All rights reserved.

Diminishing-cues retrieval practice: A memory-enhancing technique that works when regular testing doesn't.

PubMed

Fiechter, Joshua L; Benjamin, Aaron S

2017-08-28

Retrieval practice has been shown to be a highly effective tool for enhancing memory, a fact that has led to major changes to educational practice and technology. However, when initial learning is poor, initial retrieval practice is unlikely to be successful and long-term benefits of retrieval practice are compromised or nonexistent. Here, we investigate the benefit of a scaffolded retrieval technique called diminishing-cues retrieval practice (Finley, Benjamin, Hays, Bjork, & Kornell, Journal of Memory and Language, 64, 289-298, 2011). Under learning conditions that favored a strong testing effect, diminishing cues and standard retrieval practice both enhanced memory performance relative to restudy. Critically, under learning conditions where standard retrieval practice was not helpful, diminishing cues enhanced memory performance substantially. These experiments demonstrate that diminishing-cues retrieval practice can widen the range of conditions under which testing can benefit memory, and so can serve as a model for the broader application of testing-based techniques for enhancing learning.

Shock wave viscosity measurements

NASA Astrophysics Data System (ADS)

Celliers, Peter

2013-06-01

Several decades ago a method was proposed and demonstrated to measure the viscosity of fluids at high pressure by observing the oscillatory damping of sinusoidal perturbations on a shock front. A detailed mathematical analysis of the technique carried out subsequently by Miller and Ahrens revealed its potential, as well as a deep level of complexity in the analysis. We revisit the ideas behind this technique in the context of a recent experimental development: two-dimensional imaging velocimetry. The new technique allows one to capture a broad spectrum of perturbations down to few micron scale-lengths imposed on a shock front from an initial perturbation. The detailed evolution of the perturbation spectrum is sensitive to the viscosity in the fluid behind the shock front. Initial experiments are aimed at examining the viscosity of shock compressed SiO2 just above the shock melting transition. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Monitoring Interfacial Lipid Oxidation in Oil-in-Water Emulsions Using Spatially Resolved Optical Techniques.

PubMed

Banerjee, Chiranjib; Westberg, Michael; Breitenbach, Thomas; Bregnhøj, Mikkel; Ogilby, Peter R

2017-06-06

The oxidation of lipids is an important phenomenon with ramifications for disciplines that range from food science to cell biology. The development and characterization of tools and techniques to monitor lipid oxidation are thus relevant. Of particular significance in this regard are tools that facilitate the study of oxidations at interfaces in heterogeneous samples (e.g., oil-in-water emulsions, cell membranes). In this article, we establish a proof-of-principle for methods to initiate and then monitor such oxidations with high spatial resolution. The experiments were performed using oil-in-water emulsions of polyunsaturated fatty acids (PUFAs) prepared from cod liver oil. We produced singlet oxygen at a point near the oil-water interface of a given PUFA droplet in a spatially localized two-photon photosensitized process. We then followed the oxidation reactions initiated by this process with the fluorescence-based imaging technique of structured illumination microscopy (SIM). We conclude that the approach reported herein has attributes well-suited to the study of lipid oxidation in heterogeneous samples.

Damage Evaluation for Ti Alloys in Creep based on Incompatibility Field Measurement via EBSD Technique and Micro-Pillar Experiments Toward Identification of Roles of Dislocation Substructures on Fatigue Crack Initiation

DTIC Science & Technology

2011-02-07

Reproduction of a slip band with a PSB -ladder-like internal structure is attempted assuming initial conditions with and without corresponding strain...into heat at the PSB region, the present study extensively examined possible transition mechanisms toward the growth of grooves thereabout and that...arrangements even with the same dislocation density. (2)A slip band-like region having a substructure mimicking PSB ladder is demonstrated to be

The NLM Indexing Initiative's Medical Text Indexer.

PubMed

Aronson, Alan R; Mork, James G; Gay, Clifford W; Humphrey, Susanne M; Rogers, Willie J

2004-01-01

The Medical Text Indexer (MTI) is a program for producing MeSH indexing recommendations. It is the major product of NLM's Indexing Initiative and has been used in both semi-automated and fully automated indexing environments at the Library since mid 2002. We report here on an experiment conducted with MEDLINE indexers to evaluate MTI's performance and to generate ideas for its improvement as a tool for user-assisted indexing. We also discuss some filtering techniques developed to improve MTI's accuracy for use primarily in automatically producing the indexing for several abstracts collections.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Philippe, Sebastien

A system that can compare physical objects while potentially protecting sensitive information about the objects themselves has been demonstrated experimentally at the U.S. Department of Energy’s (DOE) Princeton Plasma Physics Laboratory (PPPL). This work, by researchers at Princeton University and PPPL, marks an initial confirmation of the application of a powerful cryptographic technique in the physical world. Graduate student Sébastien Philippe discusses the experiment.

Influence of Small Change of Porosity on Shock Initiation of an HMX/TATB/Viton Explosive and Ignition and Growth Modeling

NASA Astrophysics Data System (ADS)

Liu, Yan; Hussain, Tariq; Huang, Fenglei; Duan, Zhuoping

2016-07-01

All solid explosives in practical use are more or less porous. Although it is known that the change in porosity affects the shock sensitivity of solid explosives, the effect of small changes in porosity on the sensitivity needs to be determined for safe and efficient use of explosive materials. In this study, the influence of a small change in porosity on shock initiation and the subsequent detonation growth process of a plastic-bonded explosive PBXC03, composed of 87% cyclotetramethylene-tetranitramine (HMX), 7% triaminotrinitrobenzene (TATB), and 6% Viton by weight, are investigated by shock to detonation transition experiments. Two explosive formulations of PBXC03 having the same initial grain sizes pressed to 98 and 99% of theoretical mass density (1.873 g/cm3) respectively are tested using the in situ manganin piezoresistive pressure gauge technique. Numerical modeling of the experiments is performed using an ignition and growth reactive flow model. Reasonable agreement with the experimental results is obtained by increasing the growth term coefficient in the Lee-Tarver ignition and growth model with porosity. Combining the experimental and simulation results shows that the shock sensitivity increases with porosity for PBXC03 having the same explosive initial grain sizes for the pressures (about 3.1 GPa) applied in the experiments.

Oceanic ensemble forecasting in the Gulf of Mexico: An application to the case of the Deep Water Horizon oil spill

NASA Astrophysics Data System (ADS)

Khade, Vikram; Kurian, Jaison; Chang, Ping; Szunyogh, Istvan; Thyng, Kristen; Montuoro, Raffaele

2017-05-01

This paper demonstrates the potential of ocean ensemble forecasting in the Gulf of Mexico (GoM). The Bred Vector (BV) technique with one week rescaling frequency is implemented on a 9 km resolution version of the Regional Ocean Modelling System (ROMS). Numerical experiments are carried out by using the HYCOM analysis products to define the initial conditions and the lateral boundary conditions. The growth rates of the forecast uncertainty are estimated to be about 10% of initial amplitude per week. By carrying out ensemble forecast experiments with and without perturbed surface forcing, it is demonstrated that in the coastal regions accounting for uncertainties in the atmospheric forcing is more important than accounting for uncertainties in the ocean initial conditions. In the Loop Current region, the initial condition uncertainties, are the dominant source of the forecast uncertainty. The root-mean-square error of the Lagrangian track forecasts at the 15-day forecast lead time can be reduced by about 10 - 50 km using the ensemble mean Eulerian forecast of the oceanic flow for the computation of the tracks, instead of the single-initial-condition Eulerian forecast.

Interaction of the Global Energy and Water Cycle Experiment (GEWEX) Water Resources Applications Project (WRAP) and Coordinated Enhanced Observing Project (CEOP) in Support of Water Resource Management and Planning

NASA Astrophysics Data System (ADS)

Martz, L.

2004-05-01

The Water Resources Applications Project (WRAP) has been developed within the Global Energy and Water Cycle Experiment (GEWEX) to facilitate the testing of GEWEX products and their transfer to operational water managers. The WRAP activity builds upon projects within the GEWEX Continental Scale Experiments (CSEs), and facilitates dialogue between these CSEs and their local water management communities regarding their information needs and opportunities for GEWEX products to meet those needs. Participating Continental Scale Experiments are located in the United States, the Mackenzie River Basin in Canada, the Amazon River Basin in Brazil, the Baltic Sea drainage area, eastern Asia and the Murray-Darling Basin in Australia. In addition, the development of WRAP is facilitating the transfer of techniques and demonstration projects to other areas through collaboration with IAHS, UNESCO/WMO HELP, WMO Hydrology and WWAP. The initiation of CEOP presents a significant new opportunity for collaborations to support the application of global hydro-climatological scientific data and techniques to water resource management. Some important scientific and operational issues identified by water resource management professionals in earlier workshops will be reviewed, some scientific initiatives needed to address these issues will be presented, and some case study examples of the application of GEWEX knowledge to water resource problems will be presented. Against this background, the unique opportunities that CEOP provides to improve our use and management of water resources globally will be discussed.

Using the modern Silverhawk™ atherectomy catheter to characterize biliary structures that appear malignant: review of initial experience

PubMed Central

Schwartz, Jason J; Thiesset, Heather F; Clayton, Frederic; Adler, Douglas G; Hutson, William R; Carlisle, James G

2011-01-01

Background Diagnosis of a biliary stricture often hinges on cytological interpretation. In the absence of accompanying stroma, these results can often be equivocal. In theory, advanced shave biopsy techniques would allow for the preservation of tissue architecture and a more accurate definition of biliary pathology. Objectives We sought to determine the initial diagnostic utility of the modern Silverhawk™ atherectomy (SA) catheter in the evaluation of biliary strictures that appear to be malignant. Methods A total of 141 patients with biliary pathology were identified during a retrospective review of medical records for the years 2006–2011. The SA catheter was employed 12 times in seven patients for whom a tissue diagnosis was otherwise lacking. Results Neoplasia was definitively excluded in seven specimens from four patients. These four individuals were followed for 1–5 years to exclude the development of cholangiocarcinoma (CC). Samples were positive for CC in three patients, one of whom became eligible for neoadjuvant therapy and orthotopic liver transplantation. Conclusions The SA catheter appears to be a useful adjunct in diagnosing patients with biliary pathology. The existence of this technique, predicated on tissue architecture, may impact therapy, allow more timely diagnosis, and exclude cases of equivocal cytology. Although the initial results of SA use are promising, more experience is required to effectively determine its clinical accuracy. PMID:21999597

Teaching an engine-driven preparation technique to undergraduates: initial observations.

PubMed

Hänni, S; Schönenberger, K; Peters, O A; Barbakow, F

2003-07-01

This paper describes the initial experiences following the introduction of a rotary engine-driven preparation technique into the undergraduate endodontic programme at the Zurich University Dental Centre. Forty third-year students practised the ProFile.04 (PF.04) technique between January and July 2001 in a preclinical course. Between November 2001 and February 2002, 20 of these students (Group A) root-treated 51 teeth in their clinical course using either PF.04, the balanced force technique (BFT) or a combination of both. The second group of 20 students (Group B) similarly treated another 36 randomly selected teeth between April and July 2002. Types of teeth treated by the students and the canal preparation techniques were recorded. The students also completed a short questionnaire, evaluating their opinions of the new course. Of the 87 teeth endodontically treated during the clinical course, 34, 14 and 39 were shaped using PF.04 alone, a combination of PF.04 and BFT and BFT alone, respectively. No rotary instruments were fractured during the 1-year clinical course, although some instruments were fractured during the preclinical laboratory course. Overall, the students rated the rotary technique as positive. A rotary technique was successfully introduced into an undergraduate endodontic programme (this will be continued in the foreseeable future). However, the continuity between the preclinical and the clinical courses was poor as a result of the constraints of the general teaching programme.

A magnet built on bronchoscopic suction for extraction of tracheobronchial headscarf pins: a novel technique and review of a tertiary centre experience†

PubMed Central

Elsayed, Hany H.; Mostafa, Ahmed M.; Soliman, Saleh; El-Bawab, Hatem Y.; Moharram, Adel A.; El-Nori, Ahmed A.

2016-01-01

OBJECTIVES Airway metal pins are one of the most commonly inhaled foreign bodies in Eastern societies in young females wearing headscarves. We innovated a modified bronchoscopic technique to extract tracheobronchial headscarf pins by the insertion of a magnet to allow an easy and non-traumatic extraction of the pins. The aim of this study was to assess the feasibility and safety of our new technique and compare it with our large previous experience with the classic bronchoscopic method of extraction of tracheobronchial headscarf pins. METHODS We performed a study comparing our retrospective experience of classic bronchoscopic extraction from February 2004 to January 2014 and prospective experience with our modified technique using the magnet from January 2014 to June 2015. An institutional review board and new device approval were obtained. RESULTS Three hundred and twenty-six procedures on 315 patients were performed during our initial 10-year experience. Of them, 304 patients were females. The median age of our group was 13 (0–62). The median time from inhalation to procedure was 1 day (0–1022). After introducing our modified new technique using the magnet, 20 procedures were performed. Nineteen were females. The median time of the procedure and the need to forcefully bend the pin for extraction were in favour of the new technique in comparison with our classic approach (2 vs 6 min; P < 0.001) (2 patients = 20% vs 192 = 58%; P < 0.001). The conversion rate to surgery was also in favour of the modified technique but did not reach statistical significance (0 = 0% vs 15 = 4.8%; P = 0.32). All patients who underwent the modified technique were discharged home on the same day of the procedure. No procedural complications were recorded. All remain well on a follow-up period of up to 14 months. CONCLUSIONS Bronchoscopic extraction of tracheobronchial inhaled headscarf pins using a novel technique using homemade magnets was safer and simpler in comparison with our large experience with the classic approach. We advise the use of this device (or concept) in selected patients in centres dealing with this problem. PMID:26850113

Data Assimilation using Artificial Neural Networks for the global FSU atmospheric model

NASA Astrophysics Data System (ADS)

Cintra, Rosangela; Cocke, Steven; Campos Velho, Haroldo

2015-04-01

Data assimilation is the process by which measurements and model predictions are combined to obtain an accurate representation of the state of the modeled system. Uncertainty is the characteristic of the atmosphere, coupled with inevitable inadequacies in observations and computer models and increase errors in weather forecasts. Data assimilation is a technique to generate an initial condition to a weather or climate forecasts. This paper shows the results of a data assimilation technique using artificial neural networks (ANN) to obtain the initial condition to the atmospheric general circulation model (AGCM) for the Florida State University in USA. The Local Ensemble Transform Kalman filter (LETKF) is implemented with Florida State University Global Spectral Model (FSUGSM). The ANN data assimilation is made to emulate the initial condition from LETKF to run the FSUGSM. LETKF is a version of Kalman filter with Monte-Carlo ensembles of short-term forecasts to solve the data assimilation problem. The model FSUGSM is a multilevel (27 vertical levels) spectral primitive equation model with a vertical sigma coordinate. All variables are expanded horizontally in a truncated series of spherical harmonic functions (at resolution T63) and a transform technique is applied to calculate the physical processes in real space. The LETKF data assimilation experiments are based in synthetic observations data (surface pressure, absolute temperature, zonal component wind, meridional component wind and humidity). For the ANN data assimilation scheme, we use Multilayer Perceptron (MLP-DA) with supervised training algorithm where ANN receives input vectors with their corresponding response or target output from LETKF scheme. An automatic tool that finds the optimal representation to these ANNs configures the MLP-DA in this experiment. After the training process, the scheme MLP-DA is seen as a function of data assimilation where the inputs are observations and a short-range forecast to each model grid point. The ANNs were trained with data from each month of 2001, 2002, 2003, and 2004. A hind-casting experiment for data assimilation cycle using MLP-DA was performed with synthetic observations for January 2005. The numerical results demonstrate the effectiveness of the ANN technique for atmospheric data assimilation, since the analyses (initial conditions) have similar quality to LETKF analyses. The major advantage of using MLP-DA is the computational performance, which is faster than LETKF. The reduced computational cost allows the inclusion of greater number of observations and new data sources and the use of high resolution of models, which ensures the accuracy of analysis and of its weather prediction

Underwater spark discharge with long transmission line for cleaning horizontal wells

NASA Astrophysics Data System (ADS)

Lee, Kern; Chung, Kyoung-Jae; Hwang, Y. S.; Kim, C. Y.

2017-06-01

A transmission line is discussed for application in an underwater spark-discharge technique in the cleaning of a horizontal well by incorporating a power-transmission model into the simulation. The pulsed-spark-discharge technique has been proposed for clogged-well rehabilitation, because it removes incrustations that are attached to well screens by using strong pressure waves that are generated by the rapid expansion of a spark channel. To apply the pulsed-spark-discharge technique to the cleaning of horizontal wells, the coaxial cable between the pulsed power supply and the spark gap as a load needs to be extended to a few hundred meters. Prior to field application, pulsed-spark-discharge experiments were conducted and the role of the transmission line was examined using an improved simulation model. In the model, a non-linear interaction of the spark channel and the capacitor bank is described by the pulse-forming action of the coaxial cable. Based on the accurate physical properties of the water plasma, such as the equation of state and electrical conductivity within the region of interest, the amount of energy contributed to the development of a shock wave was evaluated. The simulation shows that if the initial conditions of the spark channel are the same, no further reduction in strength of the pressure wave occurs, even if the cable length is increased above 50 m. Hence, the degraded peak pressure that was observed in the experiments using the longer cable is attributed to a change in the initial condition of the spark channel. The parametric study suggests that the low initial charging voltage, the high ambient water pressure, and the long cable length yield the low initial spark-channel density, which results in a reduced peak pressure. The simulation of line charging is presented to discuss the principle of disturbing the pre-breakdown process by an extended cable.

A hybrid optimization approach to the estimation of distributed parameters in two-dimensional confined aquifers

USGS Publications Warehouse

Heidari, M.; Ranjithan, S.R.

1998-01-01

In using non-linear optimization techniques for estimation of parameters in a distributed ground water model, the initial values of the parameters and prior information about them play important roles. In this paper, the genetic algorithm (GA) is combined with the truncated-Newton search technique to estimate groundwater parameters for a confined steady-state ground water model. Use of prior information about the parameters is shown to be important in estimating correct or near-correct values of parameters on a regional scale. The amount of prior information needed for an accurate solution is estimated by evaluation of the sensitivity of the performance function to the parameters. For the example presented here, it is experimentally demonstrated that only one piece of prior information of the least sensitive parameter is sufficient to arrive at the global or near-global optimum solution. For hydraulic head data with measurement errors, the error in the estimation of parameters increases as the standard deviation of the errors increases. Results from our experiments show that, in general, the accuracy of the estimated parameters depends on the level of noise in the hydraulic head data and the initial values used in the truncated-Newton search technique.In using non-linear optimization techniques for estimation of parameters in a distributed ground water model, the initial values of the parameters and prior information about them play important roles. In this paper, the genetic algorithm (GA) is combined with the truncated-Newton search technique to estimate groundwater parameters for a confined steady-state ground water model. Use of prior information about the parameters is shown to be important in estimating correct or near-correct values of parameters on a regional scale. The amount of prior information needed for an accurate solution is estimated by evaluation of the sensitivity of the performance function to the parameters. For the example presented here, it is experimentally demonstrated that only one piece of prior information of the least sensitive parameter is sufficient to arrive at the global or near-global optimum solution. For hydraulic head data with measurement errors, the error in the estimation of parameters increases as the standard deviation of the errors increases. Results from our experiments show that, in general, the accuracy of the estimated parameters depends on the level of noise in the hydraulic head data and the initial values used in the truncated-Newton search technique.

Reliable transformation system for Microbotryum lychnidis-dioicae informed by genome and transcriptome project.

PubMed

Toh, Su San; Treves, David S; Barati, Michelle T; Perlin, Michael H

2016-10-01

Microbotryum lychnidis-dioicae is a member of a species complex infecting host plants in the Caryophyllaceae. It is used as a model system in many areas of research, but attempts to make this organism tractable for reverse genetic approaches have not been fruitful. Here, we exploited the recently obtained genome sequence and transcriptome analysis to inform our design of constructs for use in Agrobacterium-mediated transformation techniques currently available for other fungi. Reproducible transformation was demonstrated at the genomic, transcriptional and functional levels. Moreover, these initial proof-of-principle experiments provide evidence that supports the findings from initial global transcriptome analysis regarding expression from the respective promoters under different growth conditions of the fungus. The technique thus provides for the first time the ability to stably introduce transgenes and over-express target M. lychnidis-dioicae genes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kay, Jeffrey J.; Park, Samuel; Kohl, Ian Thomas

In this work, shock-induced reactions in high explosives and their chemical mechanisms were investigated using state-of-the-art experimental and theoretical techniques. Experimentally, ultrafast shock interrogation (USI, an ultrafast interferometry technique) and ultrafast absorption spectroscopy were used to interrogate shock compression and initiation of reaction on the picosecond timescale. The experiments yielded important new data that appear to indicate reaction of high explosives on the timescale of tens of picoseconds in response to shock compression, potentially setting new upper limits on the timescale of reaction. Theoretically, chemical mechanisms of shock-induced reactions were investigated using density functional theory. The calculations generated important insightsmore » regarding the ability of several hypothesized mechanisms to account for shock-induced reactions in explosive materials. The results of this work constitute significant advances in our understanding of the fundamental chemical reaction mechanisms that control explosive sensitivity and initiation of detonation.« less

Anaesthetic management for awake craniotomy in brain glioma resection: initial experience in Military Hospital Mohamed V of Rabat

PubMed Central

Meziane, Mohammed; Elkoundi, Abdelghafour; Ahtil, Redouane; Guazaz, Miloudi; Mustapha, Bensghir; Haimeur, Charki

2017-01-01

The awake brain surgery is an innovative approach in the treatment of tumors in the functional areas of the brain. There are various anesthetic techniques for awake craniotomy (AC), including asleep-awake-asleep technique, monitored anesthesia care, and the recent introduced awake-awake-awake method. We describe our first experience with anesthetic management for awake craniotomy, which was a combination of these techniques with scalp nerve block, and propofol/rémifentanil target controlled infusion. A 28-year-oldmale underwent an awake craniotomy for brain glioma resection. The scalp nerve block was performed and a low sedative state was maintained until removal of bone flap. During brain glioma resection, the patient awake state was maintained without any complications. Once, the tumorectomy was completed, the level of anesthesia was deepened and a laryngeal mask airway was inserted. A well psychological preparation, a reasonable choice of anesthetic techniques and agents, and continuous team communication were some of the key challenges for successful outcome in our patient. PMID:28904684

A magnet built on bronchoscopic suction for extraction of tracheobronchial headscarf pins: a novel technique and review of a tertiary centre experience.

PubMed

Elsayed, Hany H; Mostafa, Ahmed M; Soliman, Saleh; El-Bawab, Hatem Y; Moharram, Adel A; El-Nori, Ahmed A

2016-05-01

Airway metal pins are one of the most commonly inhaled foreign bodies in Eastern societies in young females wearing headscarves. We innovated a modified bronchoscopic technique to extract tracheobronchial headscarf pins by the insertion of a magnet to allow an easy and non-traumatic extraction of the pins. The aim of this study was to assess the feasibility and safety of our new technique and compare it with our large previous experience with the classic bronchoscopic method of extraction of tracheobronchial headscarf pins. We performed a study comparing our retrospective experience of classic bronchoscopic extraction from February 2004 to January 2014 and prospective experience with our modified technique using the magnet from January 2014 to June 2015. An institutional review board and new device approval were obtained. Three hundred and twenty-six procedures on 315 patients were performed during our initial 10-year experience. Of them, 304 patients were females. The median age of our group was 13 (0-62). The median time from inhalation to procedure was 1 day (0-1022). After introducing our modified new technique using the magnet, 20 procedures were performed. Nineteen were females. The median time of the procedure and the need to forcefully bend the pin for extraction were in favour of the new technique in comparison with our classic approach (2 vs 6 min; P < 0.001) (2 patients = 20% vs 192 = 58%; P < 0.001). The conversion rate to surgery was also in favour of the modified technique but did not reach statistical significance (0 = 0% vs 15 = 4.8%; P = 0.32). All patients who underwent the modified technique were discharged home on the same day of the procedure. No procedural complications were recorded. All remain well on a follow-up period of up to 14 months. Bronchoscopic extraction of tracheobronchial inhaled headscarf pins using a novel technique using homemade magnets was safer and simpler in comparison with our large experience with the classic approach. We advise the use of this device (or concept) in selected patients in centres dealing with this problem. © The Author 2016. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Noncoherent Doppler tracking: first flight results

NASA Astrophysics Data System (ADS)

DeBoy, Christopher C.; Robert Jensen, J.; Asher, Mark S.

2005-01-01

Noncoherent Doppler tracking has been devised as a means to achieve highly accurate, two-way Doppler measurements with a simple, transceiver-based communications system. This technique has been flown as an experiment on the Thermosphere, Ionosphere, Mesosphere, Energetics and Dynamics (TIMED) spacecraft, (launched 7 December 2001), as the operational technique for Doppler tracking on CONTOUR, and is baselined on several future deep space missions at JHU/APL. This paper reports on initial results from a series of successful tests of this technique between the TIMED spacecraft and NASA ground stations in the Deep Space Network. It also examines the advantages that noncoherent Doppler tracking and a transceiver-based system may offer to small satellite systems, including reduced cost, mass, and power.

Characterization of hypervelocity metal fragments for explosive initiation

DOE PAGES

Yeager, John D.; Bowden, Patrick R.; Guildenbecher, Daniel R.; ...

2017-07-17

The fragment impact response of two plastic-bonded explosive (PBX) formulations was studied using explosively driven aluminum fragments. A generic aluminum-capped detonator generated sub-mm aluminum particles moving at hypersonic velocities. The ability of these fragments to initiate reaction or otherwise damage two PBX materials was assessed using go/no-go experiments at standoff distances of up to 160 mm. Lower density PBX 9407 (RDX-based) was initiable at up to 115 mm, while higher density PBX 9501 (HMX-based) was only initiable at up to 6 mm. Several techniques were used to characterize the size, distribution, and velocity of the particles. Witness plate materials, includingmore » copper and polycarbonate, and backlit high speed video were used to characterize the distribution of particles, finding that the aluminum cap did not fragment homogeneously but rather with larger particles in a ring surrounding finer particles. Finally, precise digital holography experiments were conducted to measure the three-dimensional shape and size of the fastest-moving fragments, which ranged between 100 and 700 μm and traveled between 2.2 and 3.2 km/s. Crucially, these experiments showed variability in the fragmentation in terms of the number of fragments at the leading edge of the fragment field, indicating that both single and multiple shock impacts could be imparted to the target material. As a result, these types of data are critical for safety experiments and hydrocode simulations to quantify shock-to-detonation transition mechanisms and the associated risk-margins for these materials.« less

Characterization of hypervelocity metal fragments for explosive initiation

NASA Astrophysics Data System (ADS)

Yeager, John D.; Bowden, Patrick R.; Guildenbecher, Daniel R.; Olles, Joseph D.

2017-07-01

The fragment impact response of two plastic-bonded explosive (PBX) formulations was studied using explosively driven aluminum fragments. A generic aluminum-capped detonator generated sub-mm aluminum particles moving at hypersonic velocities. The ability of these fragments to initiate reaction or otherwise damage two PBX materials was assessed using go/no-go experiments at standoff distances of up to 160 mm. Lower density PBX 9407 (RDX-based) was initiable at up to 115 mm, while higher density PBX 9501 (HMX-based) was only initiable at up to 6 mm. Several techniques were used to characterize the size, distribution, and velocity of the particles. Witness plate materials, including copper and polycarbonate, and backlit high speed video were used to characterize the distribution of particles, finding that the aluminum cap did not fragment homogeneously but rather with larger particles in a ring surrounding finer particles. Finally, precise digital holography experiments were conducted to measure the three-dimensional shape and size of the fastest-moving fragments, which ranged between 100 and 700 μm and traveled between 2.2 and 3.2 km/s. Crucially, these experiments showed variability in the fragmentation in terms of the number of fragments at the leading edge of the fragment field, indicating that both single and multiple shock impacts could be imparted to the target material. These types of data are critical for safety experiments and hydrocode simulations to quantify shock-to-detonation transition mechanisms and the associated risk-margins for these materials.

Velocity navigator for motion compensated thermometry.

PubMed

Maier, Florian; Krafft, Axel J; Yung, Joshua P; Stafford, R Jason; Elliott, Andrew; Dillmann, Rüdiger; Semmler, Wolfhard; Bock, Michael

2012-02-01

Proton resonance frequency shift thermometry is sensitive to breathing motion that leads to incorrect phase differences. In this work, a novel velocity-sensitive navigator technique for triggering MR thermometry image acquisition is presented. A segmented echo planar imaging pulse sequence was modified for velocity-triggered temperature mapping. Trigger events were generated when the estimated velocity value was less than 0.2 cm/s during the slowdown phase in parallel to the velocity-encoding direction. To remove remaining high-frequency spikes from pulsation in real time, a Kalman filter was applied to the velocity navigator data. A phantom experiment with heating and an initial volunteer experiment without heating were performed to show the applicability of this technique. Additionally, a breath-hold experiment was conducted for comparison. A temperature rise of ΔT = +37.3°C was seen in the phantom experiment, and a root mean square error (RMSE) outside the heated region of 2.3°C could be obtained for periodic motion. In the volunteer experiment, a RMSE of 2.7°C/2.9°C (triggered vs. breath hold) was measured. A novel velocity navigator with Kalman filter postprocessing in real time significantly improves the temperature accuracy over non-triggered acquisitions and suggests being comparable to a breath-held acquisition. The proposed technique might be clinically applied for monitoring of thermal ablations in abdominal organs.

Twenty and thirty GHz millimeter wave experiments with the ATS-6 satellite

NASA Technical Reports Server (NTRS)

Ippolito, L. J. (Compiler)

1975-01-01

The ATS-6 millimeter wave experiment, provided the first direct measurements of 20 and 30 GHz earth-space links from an orbiting satellite. Studies at eleven locations in the continental United States were directed at an evaluation of rain attenuation effects, scintillations, depolarization, site diversity, coherence bandwidth, and analog and digital communications techniques. In addition to direct measurements on the 20 and 30 GHz links, methods of attenuation prediction with radars, rain gages, and radiometers were developed and compared with the directly measured attenuation. Initial data results of the ATS-6 millimeter wave experiment from the major participating organizations are presented.

Electrically Driven Thermal Management: Flight Validation, Experiment Development, Future Technologies

NASA Technical Reports Server (NTRS)

Didion, Jeffrey R.

2018-01-01

Electrically Driven Thermal Management is an active research and technology development initiative incorporating ISS technology flight demonstrations (STP-H5), development of Microgravity Science Glovebox (MSG) flight experiment, and laboratory-based investigations of electrically based thermal management techniques. The program targets integrated thermal management for future generations of RF electronics and power electronic devices. This presentation reviews four program elements: i.) results from the Electrohydrodynamic (EHD) Long Term Flight Demonstration launched in February 2017 ii.) development of the Electrically Driven Liquid Film Boiling Experiment iii.) two University based research efforts iv.) development of Oscillating Heat Pipe evaluation at Goddard Space Flight Center.

Analyses and forecasts of a tornadic supercell outbreak using a 3DVAR system ensemble

NASA Astrophysics Data System (ADS)

Zhuang, Zhaorong; Yussouf, Nusrat; Gao, Jidong

2016-05-01

As part of NOAA's "Warn-On-Forecast" initiative, a convective-scale data assimilation and prediction system was developed using the WRF-ARW model and ARPS 3DVAR data assimilation technique. The system was then evaluated using retrospective short-range ensemble analyses and probabilistic forecasts of the tornadic supercell outbreak event that occurred on 24 May 2011 in Oklahoma, USA. A 36-member multi-physics ensemble system provided the initial and boundary conditions for a 3-km convective-scale ensemble system. Radial velocity and reflectivity observations from four WSR-88Ds were assimilated into the ensemble using the ARPS 3DVAR technique. Five data assimilation and forecast experiments were conducted to evaluate the sensitivity of the system to data assimilation frequencies, in-cloud temperature adjustment schemes, and fixed- and mixed-microphysics ensembles. The results indicated that the experiment with 5-min assimilation frequency quickly built up the storm and produced a more accurate analysis compared with the 10-min assimilation frequency experiment. The predicted vertical vorticity from the moist-adiabatic in-cloud temperature adjustment scheme was larger in magnitude than that from the latent heat scheme. Cycled data assimilation yielded good forecasts, where the ensemble probability of high vertical vorticity matched reasonably well with the observed tornado damage path. Overall, the results of the study suggest that the 3DVAR analysis and forecast system can provide reasonable forecasts of tornadic supercell storms.

Error Propagation Analysis in the SAE Architecture Analysis and Design Language (AADL) and the EDICT Tool Framework

NASA Technical Reports Server (NTRS)

LaValley, Brian W.; Little, Phillip D.; Walter, Chris J.

2011-01-01

This report documents the capabilities of the EDICT tools for error modeling and error propagation analysis when operating with models defined in the Architecture Analysis & Design Language (AADL). We discuss our experience using the EDICT error analysis capabilities on a model of the Scalable Processor-Independent Design for Enhanced Reliability (SPIDER) architecture that uses the Reliable Optical Bus (ROBUS). Based on these experiences we draw some initial conclusions about model based design techniques for error modeling and analysis of highly reliable computing architectures.

Initial velocity V-shapes of young asteroid families

NASA Astrophysics Data System (ADS)

Bolin, Bryce T.; Walsh, Kevin J.; Morbidelli, Alessandro; Delbó, Marco

2018-01-01

Ejection velocity fields of asteroid families are largely unconstrained due to the fact that members disperse relatively quickly on Myr time-scales by secular resonances and the Yarkovsky effect. The spreading of fragments in a by the Yarkovsky effect is indistinguishable from the spreading caused by the initial ejection of fragments. By examining families <20 Myr old, we can use the V-shape identification technique to separate family shapes that are due to the initial ejection velocity field and those that are due to the Yarkovsky effect. Asteroid families that are <20 Myr old provide an opportunity to study the velocity field of family fragments before they become too dispersed. Only the Karin family's initial velocity field has been determined and scales inversely with diameter, D-1. We have applied the V-shape identification technique to constrain young families' initial ejection velocity fields by measuring the curvature of their fragments' V-shape correlation in semimajor axis, a, versus D-1 space. Curvature from a straight line implies a deviation from a scaling of D-1. We measure the V-shape curvature of 11 young asteroid families including the 1993 FY12, Aeolia, Brangane, Brasilia, Clarissa, Iannini, Karin, Konig, Koronis(2), Theobalda and Veritas asteroid families. We find that the majority of asteroid families have initial ejection velocity fields consistent with ∼D-1 supporting laboratory impact experiments and computer simulations of disrupting asteroid parent bodies.

Robotic and endoscopic transoral thyroidectomy: feasibility and description of the technique in the cadaveric model.

PubMed

Kahramangil, Bora; Mohsin, Khuzema; Alzahrani, Hassan; Bu Ali, Daniah; Tausif, Syed; Kang, Sang-Wook; Kandil, Emad; Berber, Eren

2017-12-01

Numerous new approaches have been described over the years to improve the cosmetic outcomes of thyroid surgery. Transoral approach is a new technique that aims to achieve superior cosmetic outcomes by concealing the incision in the oral cavity. Transoral thyroidectomy through vestibular approach was performed in two institutions on cadaveric models. Procedure was performed endoscopically in one institution, while the robotic technique was utilized at the other. Transoral thyroidectomy was successfully performed at both institutions with robotic and endoscopic techniques. All vital structures were identified and preserved. Transoral thyroidectomy has been performed in animal and cadaveric models, as well as in some clinical studies. Our initial experience indicates the feasibility of this approach. More clinical studies are required to elucidate its full utility.

Proposed minimum reporting standards for chemical analysis Chemical Analysis Working Group (CAWG) Metabolomics Standards Initiative (MSI)

PubMed Central

Amberg, Alexander; Barrett, Dave; Beale, Michael H.; Beger, Richard; Daykin, Clare A.; Fan, Teresa W.-M.; Fiehn, Oliver; Goodacre, Royston; Griffin, Julian L.; Hankemeier, Thomas; Hardy, Nigel; Harnly, James; Higashi, Richard; Kopka, Joachim; Lane, Andrew N.; Lindon, John C.; Marriott, Philip; Nicholls, Andrew W.; Reily, Michael D.; Thaden, John J.; Viant, Mark R.

2013-01-01

There is a general consensus that supports the need for standardized reporting of metadata or information describing large-scale metabolomics and other functional genomics data sets. Reporting of standard metadata provides a biological and empirical context for the data, facilitates experimental replication, and enables the re-interrogation and comparison of data by others. Accordingly, the Metabolomics Standards Initiative is building a general consensus concerning the minimum reporting standards for metabolomics experiments of which the Chemical Analysis Working Group (CAWG) is a member of this community effort. This article proposes the minimum reporting standards related to the chemical analysis aspects of metabolomics experiments including: sample preparation, experimental analysis, quality control, metabolite identification, and data pre-processing. These minimum standards currently focus mostly upon mass spectrometry and nuclear magnetic resonance spectroscopy due to the popularity of these techniques in metabolomics. However, additional input concerning other techniques is welcomed and can be provided via the CAWG on-line discussion forum at http://msi-workgroups.sourceforge.net/ or http://Msi-workgroups-feedback@lists.sourceforge.net. Further, community input related to this document can also be provided via this electronic forum. PMID:24039616

Retroperitoneoscopic living donor nephrectomy: initial experience with a unique hand-assisted approach.

PubMed

Capolicchio, J-P; Feifer, A; Plante, M K; Tchervenkov, J

2011-01-01

The retroperitoneoscopic (RP) approach to live donor nephrectomy (LDN) may be advantageous for the donor because it avoids mobilization of peritoneal organs and provides direct access to the renal vessels. Notwithstanding, this approach is not popular, likely because of the steeper learning curve. We feel that hand-assistance (HA) can reduce the learning curve and in this study, we present our experience with a novel hand-assist approach to retroperitoneoscopic live donor nephrectomy (HARP-LDN). Over a one-yr period, 10 consecutive patients underwent left HARP-LDN with a mean body mass index of 29 and three with prior left abdomen surgery. The surgical technique utilizes a 7 cm, muscle-sparing incision for the hand-port with two endoscopic ports. Operative time was an average of 155 min., with no open conversions. Mean blood loss was 68 mL, and warm ischemia time was 2.5 min. Hospital stay averaged 2.7 d with postoperative complications limited to one urinary retention. Our modified HARP approach to left LDN is safe, effective and can be performed expeditiously. Our promising initial results require a larger patient cohort to confirm the advantages of the hand-assisted retroperitoneal technique. © 2010 John Wiley & Sons A/S.

Steam and air co-injection in removing residual TCE in unsaturated layered sandy porous media.

PubMed

Peng, Sheng; Wang, Ning; Chen, Jiajun

2013-10-01

Steam and air co-injection is a promising technique for volatile and semi-volatile organic contaminant remediation in heterogeneous porous media. In this study, removal of trichloroethene (TCE) with steam-air co-injection was investigated through a series of 2D sandbox experiments with different layered sand structures, and through numerical simulations. The results show that a layered structure with coarse sand, in which steam and air convection are relatively rapid, resulted in a higher removal rate and a larger removal ratio than those observed in an experiment using finer sand; however, the difference was not significant, and the removal ratios from three experiments ranged from 85% to 94%. Slight downward movement of TCE was observed for Experiment 1 (TCE initially in a fine sand zone encased in a coarse sand), while no such movement was observed for Experiment 2 (TCE initially in two fine sand layers encased in a coarse sand) or 3 (TCE initially in a silty sand zone encased in a coarse sand). Simulations show accumulation of TCE at the interface of the layered sands, which indicates a capillary barrier effect in restraining the downward movement of TCE. This effect is illustrated further by a numerical experiment with homogeneous coarse sand, in which continuous downward TCE movement to the bottom of the sandbox was simulated. Another numerical experiment with higher water saturation was also conducted. The results illustrate a complicated influence of water saturation on TCE removal in a layered sand structure. Published by Elsevier B.V.

A novel method for percutaneous insertion of a right ventricular assist device.

PubMed

Avgerinos, Dimitrios V; DeBois, William; Mongero, Linda; Krieger, Karl; Salemi, Arash

2013-06-01

Right heart failure is a rare but often fatal complication both in the pre- and postoperative setting. Right heart support with a ventricular assist device inserted in the operating room through median sternotomy can be a time-consuming procedure that requires a reoperation for removal. In cases of urgent need of right heart support, a percutaneous technique option may be of benefit. We present our initial experience with a percutaneously inserted right ventricular assist device (RVAD) in an elderly patient with severe right heart failure. An 81-year-old female patient underwent combined aortic and mitral valve replacement at our institution. During the first postoperative evening, the patient sustained sudden cardiovascular collapse and a bedside transesophageal echocardiogram revealed severe right heart failure. A coronary angiogram showed thrombosis of the right coronary artery, which was cleared with a suction device. As a result of the patient's critical condition, it was decided that an RVAD was needed as a bridge to recovery. The patient's condition improved significantly almost immediately. Her right heart function recovered over the next few days and the RVAD was removed at the bedside. She made a complete recovery and was discharged home. This patient is a prime example that a totally RVAD can be inserted in urgent situations easily and safely under fluoroscopic and echocardiographic guidance. More clinical experience with percutaneous RVADs is required to establish this technique as an alternative equivalent to the traditional open method. Right heart failure complicates many heart diseases both in the pre- and the postoperative setting. In cases of urgent need of right heart support, a percutaneous technique of a RVAD is needed for a successful outcome. We present our initial experience with a percutaneously inserted RVAD in an elderly patient with severe postoperative right heart failure.

Low Lunar Orbit Design via Graphical Manipulation of Eccentricity Vector Evolution

NASA Technical Reports Server (NTRS)

Wallace, Mark S.; Sweetser, Theodore H.; Roncoli, Ralph B.

2012-01-01

Low lunar orbits, such as those used by GRAIL and LRO, experience predictable variations in the evolution of their eccentricity vectors. These variations are nearly invariant with respect to the initial eccentricity and argument of periapse and change only in the details with respect to the initial semi-major axis. These properties suggest that manipulating the eccentricity vector evolution directly can give insight into orbit maintenance designs and can reduce the number of propagations required. A trio of techniques for determining the desired maneuvers is presented in the context of the GRAIL extended mission.

Liquid-injection for preperitoneal dissection of transabdominal preperitoneal (TAPP) inguinal [corrected] hernia repair.

PubMed

Mizota, Tomoko; Watanabe, Yusuke; Madani, Amin; Takemoto, Norihiro; Yamada, Hidehisa; Poudel, Saseem; Miyasaka, Yuji; Kurashima, Yo

2015-03-01

The creation of an adequate peritoneal flap during laparoscopic transabdominal preperitoneal (TAPP) inguinal hernia repair, while avoiding injuring surrounding structures can be technically challenging. Liquid infiltration of the preperitoneal space can help facilitate dissection and avoid inadvertent injuries. We describe a novel technique for TAPP inguinal hernia repair using liquid-injection for preperitoneal [corrected] dissection and report our initial experience. TAPP inguinal hernia repair using a liquid-injection technique during preperitoneal dissection was performed by a single surgical resident without prior TAPP repair experience from July 2013 to January 2014. After trocar placement, 60 mL of 0.3 % lidocaine with 1:300,000 dilution of epinephrine was injected percutaneously using a blunt needle under laparoscopic visualization into the preperitoneal space to assist with the dissection and parietalization of the vas deferens, spermatic vessels, and epigastric vessels. The initial peritoneal incision is performed at the lateral side of the inguinal canal, followed by blunt dissection of the preperitoneal space. Eleven patients (median age: 69; 8 male) with a total of 12 inguinal hernias underwent a TAPP repair using a liquid-injection preperitoneal dissection technique. Ten patients had unilateral hernias (4 indirect, 6 direct), and one patient had bilateral direct hernias. The median operative time, median injection time, and median dissection time were 116, 3.5, and 42 min, respectively. Estimated blood loss was less than 10 mL for all cases. No intraoperative injuries, conversions to open repair, or 30-day postoperative complications occurred. There were no hernia recurrences after a median follow-up of 143 days. Our preliminary experience suggests that liquid-injection to assist preperitoneal dissection during TAPP inguinal hernia repair appears to be safe and feasible. This novel method facilitates the dissection of spermatic cord structures, and can be used to minimize trauma to surrounding structures, especially when performed by trainees with limited operative experience.

Advancing the education in molecular diagnostics: the IFCC-Initiative "Clinical Molecular Biology Curriculum" (C-CMBC); a ten-year experience.

PubMed

Lianidou, Evi; Ahmad-Nejad, Parviz; Ferreira-Gonzalez, Andrea; Izuhara, Kenji; Cremonesi, Laura; Schroeder, Maria-Eugenia; Richter, Karin; Ferrari, Maurizio; Neumaier, Michael

2014-09-25

Molecular techniques are becoming commonplace in the diagnostic laboratory. Their applications influence all major phases of laboratory medicine including predisposition/genetic risk, primary diagnosis, therapy stratification and prognosis. Readily available laboratory hardware and wetware (i.e. consumables and reagents) foster rapid dissemination to countries that are just establishing molecular testing programs. Appropriate skill levels extending beyond the technical procedure are required for analytical and diagnostic proficiency that is mandatory in molecular genetic testing. An international committee (C-CMBC) of the International Federation for Clinical Chemistry (IFCC) was established to disseminate skills in molecular genetic testing in member countries embarking on the respective techniques. We report the ten-year experience with different teaching and workshop formats for beginners in molecular diagnostics. Copyright © 2014 Elsevier B.V. All rights reserved.

Experiences from the anatomy track in the ontology alignment evaluation initiative.

PubMed

Dragisic, Zlatan; Ivanova, Valentina; Li, Huanyu; Lambrix, Patrick

2017-12-04

One of the longest running tracks in the Ontology Alignment Evaluation Initiative is the Anatomy track which focuses on aligning two anatomy ontologies. The Anatomy track was started in 2005. In 2005 and 2006 the task in this track was to align the Foundational Model of Anatomy and the OpenGalen Anatomy Model. Since 2007 the ontologies used in the track are the Adult Mouse Anatomy and a part of the NCI Thesaurus. Since 2015 the data in the Anatomy track is also used in the Interactive track of the Ontology Alignment Evaluation Initiative. In this paper we focus on the Anatomy track in the years 2007-2016 and the Anatomy part of the Interactive track in 2015-2016. We describe the data set and the changes it went through during the years as well as the challenges it poses for ontology alignment systems. Further, we give an overview of all systems that participated in the track and the techniques they have used. We discuss the performance results of the systems and summarize the general trends. About 50 systems have participated in the Anatomy track. Many different techniques were used. The most popular matching techniques are string-based strategies and structure-based techniques. Many systems also use auxiliary information. The quality of the alignment has increased for the best performing systems since the beginning of the track and more and more systems check the coherence of the proposed alignment and implement a repair strategy. Further, interacting with an oracle is beneficial.

EFFECTS OF INTERVIEWER BEHAVIOR ON ACCURACY OF CHILDREN'S RESPONSES

PubMed Central

Sparling, Jessica; Wilder, David A; Kondash, Jennifer; Boyle, Megan; Compton, Megan

2011-01-01

Previous research has shown that certain interviewer behaviors can evoke inaccurate answers by children. In the current study, we examined the effects of approving and disapproving statements on the accuracy of 3 children's answers to questions in an interview (Experiment 1). We then evaluated 3 questioning techniques that may be used by interviewers during a forensic interview in which a child provides eyewitness testimony (Experiment 2). All participants responded with more inaccurate answers when approving statements followed inaccurate information and disapproving statements followed accurate information in Experiment 1. During Experiment 2, 1 participant responded most inaccurately when she was requestioned after providing an initial answer, whereas the remaining 2 participants responded most inaccurately when the interviewer provided cowitness information and suggestive questions. PMID:21941387

Recommended techniques for effective maintainability. A continuous improvement initiative of the NASA Reliability and Maintainability Steering Committee

NASA Technical Reports Server (NTRS)

1994-01-01

This manual presents a series of recommended techniques that can increase overall operational effectiveness of both flight and ground based NASA systems. It provides a set of tools that minimizes risk associated with: (1) restoring failed functions (both ground and flight based); (2) conducting complex and highly visible maintenance operations; and (3) sustaining a technical capability to support the NASA mission using aging equipment or facilities. It considers (1) program management - key elements of an effective maintainability effort; (2) design and development - techniques that have benefited previous programs; (3) analysis and test - quantitative and qualitative analysis processes and testing techniques; and (4) operations and operational design techniques that address NASA field experience. This document is a valuable resource for continuous improvement ideas in executing the systems development process in accordance with the NASA 'better, faster, smaller, and cheaper' goal without compromising safety.

Translating the simulation of procedural drilling techniques for interactive neurosurgical training.

PubMed

Stredney, Don; Rezai, Ali R; Prevedello, Daniel M; Elder, J Bradley; Kerwin, Thomas; Hittle, Bradley; Wiet, Gregory J

2013-10-01

Through previous efforts we have developed a fully virtual environment to provide procedural training of otologic surgical technique. The virtual environment is based on high-resolution volumetric data of the regional anatomy. These volumetric data help drive an interactive multisensory, ie, visual (stereo), aural (stereo), and tactile, simulation environment. Subsequently, we have extended our efforts to support the training of neurosurgical procedural technique as part of the Congress of Neurological Surgeons simulation initiative. To deliberately study the integration of simulation technologies into the neurosurgical curriculum and to determine their efficacy in teaching minimally invasive cranial and skull base approaches. We discuss issues of biofidelity and our methods to provide objective, quantitative and automated assessment for the residents. We conclude with a discussion of our experiences by reporting preliminary formative pilot studies and proposed approaches to take the simulation to the next level through additional validation studies. We have presented our efforts to translate an otologic simulation environment for use in the neurosurgical curriculum. We have demonstrated the initial proof of principles and define the steps to integrate and validate the system as an adjuvant to the neurosurgical curriculum.

Beryllium liner implosion experiments on the Z accelerator in preparation for magnetized liner inertial fusiona)

NASA Astrophysics Data System (ADS)

McBride, R. D.; Martin, M. R.; Lemke, R. W.; Greenly, J. B.; Jennings, C. A.; Rovang, D. C.; Sinars, D. B.; Cuneo, M. E.; Herrmann, M. C.; Slutz, S. A.; Nakhleh, C. W.; Ryutov, D. D.; Davis, J.-P.; Flicker, D. G.; Blue, B. E.; Tomlinson, K.; Schroen, D.; Stamm, R. M.; Smith, G. E.; Moore, J. K.; Rogers, T. J.; Robertson, G. K.; Kamm, R. J.; Smith, I. C.; Savage, M.; Stygar, W. A.; Rochau, G. A.; Jones, M.; Lopez, M. R.; Porter, J. L.; Matzen, M. K.

2013-05-01

Multiple experimental campaigns have been executed to study the implosions of initially solid beryllium (Be) liners (tubes) on the Z pulsed-power accelerator. The implosions were driven by current pulses that rose from 0 to 20 MA in either 100 or 200 ns (200 ns for pulse shaping experiments). These studies were conducted in support of the recently proposed Magnetized Liner Inertial Fusion concept [Slutz et al., Phys. Plasmas 17, 056303 (2010)], as well as for exploring novel equation-of-state measurement techniques. The experiments used thick-walled liners that had an aspect ratio (initial outer radius divided by initial wall thickness) of either 3.2, 4, or 6. From these studies, we present three new primary results. First, we present radiographic images of imploding Be liners, where each liner contained a thin aluminum sleeve for enhancing the contrast and visibility of the liner's inner surface in the images. These images allow us to assess the stability of the liner's inner surface more accurately and more directly than was previously possible. Second, we present radiographic images taken early in the implosion (prior to any motion of the liner's inner surface) of a shockwave propagating radially inward through the liner wall. Radial mass density profiles from these shock compression experiments are contrasted with profiles from experiments where the Z accelerator's pulse shaping capabilities were used to achieve shockless ("quasi-isentropic") liner compression. Third, we present "micro-Ḃ" measurements of azimuthal magnetic field penetration into the initially vacuum-filled interior of a shocked liner. Our measurements and simulations reveal that the penetration commences shortly after the shockwave breaks out from the liner's inner surface. The field then accelerates this low-density "precursor" plasma to the axis of symmetry.

Beryllium liner implosion experiments on the Z accelerator in preparation for magnetized liner inertial fusion

DOE Office of Scientific and Technical Information (OSTI.GOV)

McBride, R. D.; Martin, M. R.; Lemke, R. W.

Multiple experimental campaigns have been executed to study the implosions of initially solid beryllium (Be) liners (tubes) on the Z pulsed-power accelerator. The implosions were driven by current pulses that rose from 0 to 20 MA in either 100 or 200 ns (200 ns for pulse shaping experiments). These studies were conducted in support of the recently proposed Magnetized Liner Inertial Fusion concept [Slutz et al., Phys. Plasmas 17, 056303 (2010)], as well as for exploring novel equation-of-state measurement techniques. The experiments used thick-walled liners that had an aspect ratio (initial outer radius divided by initial wall thickness) of eithermore » 3.2, 4, or 6. From these studies, we present three new primary results. First, we present radiographic images of imploding Be liners, where each liner contained a thin aluminum sleeve for enhancing the contrast and visibility of the liner's inner surface in the images. These images allow us to assess the stability of the liner's inner surface more accurately and more directly than was previously possible. Second, we present radiographic images taken early in the implosion (prior to any motion of the liner's inner surface) of a shockwave propagating radially inward through the liner wall. Radial mass density profiles from these shock compression experiments are contrasted with profiles from experiments where the Z accelerator's pulse shaping capabilities were used to achieve shockless (“quasi-isentropic”) liner compression. Third, we present “micro-B-dot ” measurements of azimuthal magnetic field penetration into the initially vacuum-filled interior of a shocked liner. Our measurements and simulations reveal that the penetration commences shortly after the shockwave breaks out from the liner's inner surface. The field then accelerates this low-density “precursor” plasma to the axis of symmetry.« less

Maternal, Infant Characteristics, Breastfeeding Techniques, and Initiation: Structural Equation Modeling Approaches

PubMed Central

Htun, Tha Pyai; Lim, Peng Im; Ho-Lim, Sarah

2015-01-01

Objectives The aim of this study was to examine the relationships among maternal and infant characteristics, breastfeeding techniques, and exclusive breastfeeding initiation in different modes of birth using structural equation modeling approaches. Methods We examined a hypothetical model based on integrating concepts of a breastfeeding decision-making model, a breastfeeding initiation model, and a social cognitive theory among 952 mother-infant dyads. The LATCH breastfeeding assessment tool was used to evaluate breastfeeding techniques and two infant feeding categories were used (exclusive and non-exclusive breastfeeding). Results Structural equation models (SEM) showed that multiparity was significantly positively associated with breastfeeding techniques and the jaundice of an infant was significantly negatively related to exclusive breastfeeding initiation. A multigroup analysis in the SEM showed no difference between the caesarean section and vaginal delivery groups estimates of breastfeeding techniques on exclusive breastfeeding initiation. Breastfeeding techniques were significantly positively associated with exclusive breastfeeding initiation in the entire sample and in the vaginal deliveries group. However, breastfeeding techniques were not significantly associated with exclusive breastfeeding initiation in the cesarean section group. Maternal age, maternal race, gestations, birth weight of infant, and postnatal complications had no significant impacts on breastfeeding techniques or exclusive breastfeeding initiation in our study. Overall, the models fitted the data satisfactorily (GFI = 0.979–0.987; AGFI = 0.951–0.962; IFI = 0.958–0.962; CFI = 0.955–0.960, and RMSEA = 0.029–0.034). Conclusions Multiparity and jaundice of an infant were found to affect breastfeeding technique and exclusive breastfeeding initiation respectively. Breastfeeding technique was related to exclusive breastfeeding initiation according to the mode of birth. This relationship implies the importance of early effective interventions among first-time mothers with jaundice infants in improving breastfeeding techniques and promoting exclusive breastfeeding initiation. PMID:26566028

Evaluation Of Risk And Possible Mitigation Schemes For Previously Unidentified Hazards

NASA Technical Reports Server (NTRS)

Linzey, William; McCutchan, Micah; Traskos, Michael; Gilbrech, Richard; Cherney, Robert; Slenski, George; Thomas, Walter, III

2006-01-01

This report presents the results of arc track testing conducted to determine if such a transfer of power to un-energized wires is possible and/or likely during an arcing event, and to evaluate an array of protection schemes that may significantly reduce the possibility of such a transfer. The results of these experiments may be useful for determining the level of protection necessary to guard against spurious voltage and current being applied to safety critical circuits. It was not the purpose of these experiments to determine the probability of the initiation of an arc track event only if an initiation did occur could it cause the undesired event: an inadvertent thruster firing. The primary wire insulation used in the Orbiter is aromatic polyimide, or Kapton , a construction known to arc track under certain conditions [3]. Previous Boeing testing has shown that arc tracks can initiate in aromatic polyimide insulated 28 volts direct current (VDC) power circuits using more realistic techniques such as chafing with an aluminum blade (simulating the corner of an avionics box or lip of a wire tray), or vibration of an aluminum plate against a wire bundle [4]. Therefore, an arc initiation technique was chosen that provided a reliable and consistent technique of starting the arc and not a realistic simulation of a scenario on the vehicle. Once an arc is initiated, the current, power and propagation characteristics of the arc depend on the power source, wire gauge and insulation type, circuit protection and series resistance rather than type of initiation. The initiation method employed for these tests was applying an oil and graphite mixture to the ends of a powered twisted pair wire. The flight configuration of the heater circuits, the fuel/oxider (or ox) wire, and the RCS jet solenoid were modeled in the test configuration so that the behavior of these components during an arcing event could be studied. To determine if coil activation would occur with various protection wire schemes, 145 tests were conducted using various fuel/ox wire alternatives (shielded and unshielded) and/or different combinations of polytetrafuloroethylene (PTFE), Mystik tape and convoluted wraps to prevent unwanted coil activation. Test results were evaluated along with other pertinent data and information to develop a mitigation strategy for an inadvertent RCS firing. The SSP evaluated civilian aircraft wiring failures to search for aging trends in assessing the wire-short hazard. Appendix 2 applies Weibull statistical methods to the same data with a similar purpose.

Distributed sensor for water and pH measurements using fiber optics and swellable polymeric systems

NASA Astrophysics Data System (ADS)

Michie, W. C.; Culshaw, B.; McKenzie, I.; Konstantakis, M.; Graham, N. B.; Moran, C.; Santos, F.; Bergqvist, E.; Carlstrom, B.

1995-01-01

We report on the design, construction and test of a generic form of sensor for making distributed measurements of a range of chemical parameters. The technique combines optical time-domain reflectometry with chemically sensitive water-swellable polymers (hydrogels). Initial experiments have concentrated on demonstrating a distributed water detector; however, gels have been developed that enable this sensor to be

75 FR 35619 - Airworthiness Directives; Piper Aircraft, Inc. Models PA-32R-301T and PA-46-350P Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-23

... tighten to an July 28, 2010 (the initial torque of effective date of 40 in. lbs. Tap the this AD... installation than by a change in clamp design. Their experience shows proper installation, torque techniques, and pre-torque alignments of components go a long way in preventing clamp failures down the road. We...

Hybrid Systems Diagnosis

NASA Technical Reports Server (NTRS)

McIlraith, Sheila; Biswas, Gautam; Clancy, Dan; Gupta, Vineet

2005-01-01

This paper reports on an on-going Project to investigate techniques to diagnose complex dynamical systems that are modeled as hybrid systems. In particular, we examine continuous systems with embedded supervisory controllers that experience abrupt, partial or full failure of component devices. We cast the diagnosis problem as a model selection problem. To reduce the space of potential models under consideration, we exploit techniques from qualitative reasoning to conjecture an initial set of qualitative candidate diagnoses, which induce a smaller set of models. We refine these diagnoses using parameter estimation and model fitting techniques. As a motivating case study, we have examined the problem of diagnosing NASA's Sprint AERCam, a small spherical robotic camera unit with 12 thrusters that enable both linear and rotational motion.

Liver transplantations in Bulgaria--initial experience.

PubMed

Vladov, N; Mihaylov, V; Takorov, I; Vasilevski, I; Lukanova, T; Odisseeva, E; Katzarov, K; Simonova, M; Tomova, D; Konakchieva, M; Petrov, N; Mladenov, N; Sergeev, S; Mutafchiiski, V

2014-01-01

The filed of liver transplantation (LT) continues to evolve and is highly effective therapy for many patients with acute and chronic liver failure resulting from a variety of causes. Improvement of perioperative care, surgical technique and immunosuppression in recent years has led to its transformation into a safe and routine procedure with steadily improving results. The aim of this paper is to present the initial experience of the transplant team at Military Medical Academy - Sofia, Bulgaria. For the period of April 2007 - August 2014 the team performed 38 liver transplants in 37 patients (one retransplantation). Patients were followed up prospectively and retrospectively. In 36 (95%) patients a graft from a cadaveric donor was used and in two cases--a right liver grafts from live donor. The mean MELD score of the transplanted patients was 17 (9-40). The preferred surgical technique was "piggyback" with preservation of inferior vena cava in 33 (86%) of the cases and classical technique in 3 (8%) patients. The overall complication rate was 48%. Early mortality rate was 13% (5 patients). The overall 1- and 5-year survival is 81% and 77% respectivelly. The setting of a new LT program is a complex process which requires the effort and effective colaboration of a wide range of speciacialists (hepatologists, surgeons, anesthesiologists, psychologists, therapists, coordinators, etc.) and institutions. The good results are function of a proper selection of the donors and the recipients. Living donation is an alternative in the shortage of cadaveric donors.

Adverse childhood experiences of low-income urban youth.

PubMed

Wade, Roy; Shea, Judy A; Rubin, David; Wood, Joanne

2014-07-01

Current assessments of adverse childhood experiences (ACEs) may not adequately encompass the breadth of adversity to which low-income urban children are exposed. The purpose of this study was to identify and characterize the range of adverse childhood experiences faced by young adults who grew up in a low-income urban area. Focus groups were conducted with young adults who grew up in low-income Philadelphia neighborhoods. Using the nominal group technique, participants generated a list of adverse childhood experiences and then identified the 5 most stressful experiences on the group list. The most stressful experiences identified by participants were grouped into a ranked list of domains and subdomains. Participants identified a range of experiences, grouped into 10 domains: family relationships, community stressors, personal victimization, economic hardship, peer relationships, discrimination, school, health, child welfare/juvenile justice, and media/technology. Included in these domains were many but not all of the experiences from the initial ACEs studies; parental divorce/separation and mental illness were absent. Additional experiences not included in the initial ACEs but endorsed by our participants included single-parent homes; exposure to violence, adult themes, and criminal behavior; personal victimization; bullying; economic hardship; and discrimination. Gathering youth perspectives on childhood adversity broadens our understanding of the experience of stress and trauma in childhood. Future work is needed to determine the significance of this broader set of adverse experiences in predisposing children to poor health outcomes as adults. Copyright © 2014 by the American Academy of Pediatrics.

Video-assisted structured teaching to improve aseptic technique during neuraxial block.

PubMed

Friedman, Z; Siddiqui, N; Mahmoud, S; Davies, S

2013-09-01

Teaching epidural catheter insertion tends to focus on developing manual dexterity rather than improving aseptic technique which usually remains poor despite increasing experience. The aim of this study was to compare epidural aseptic technique performance, by novice operators after a targeted teaching intervention, with operators taught aseptic technique before the intervention was initiated. Starting July 2008, two groups of second-year anaesthesia residents (pre- and post-teaching intervention) performing their 4-month obstetric anaesthesia rotation in a university affiliated centre were videotaped three to four times while performing epidural procedures. Trained blinded independent examiners reviewed the procedures. The primary outcome was a comparison of aseptic technique performance scores (0-30 points) graded on a scale task-specific checklist. A total of 86 sessions by 29 residents were included in the study analysis. The intraclass correlation coefficient for inter-rater reliability for the aseptic technique was 0.90. The median aseptic technique scores for the rotation period were significantly higher in the post-intervention group [27.58, inter-quartile range (IQR) 22.33-29.50 vs 16.56, IQR 13.33-22.00]. Similar results were demonstrated when scores were analysed for low, moderate, and high levels of experience throughout the rotation. Procedure-specific aseptic technique teaching, aided by video assessment and video demonstration, helped significantly improve aseptic practice by novice trainees. Future studies should consider looking at retention over longer periods of time in more senior residents.

Robotic and endoscopic transoral thyroidectomy: feasibility and description of the technique in the cadaveric model

PubMed Central

Kahramangil, Bora; Mohsin, Khuzema; Alzahrani, Hassan; Bu Ali, Daniah; Tausif, Syed; Kang, Sang-Wook; Kandil, Emad

2017-01-01

Background Numerous new approaches have been described over the years to improve the cosmetic outcomes of thyroid surgery. Transoral approach is a new technique that aims to achieve superior cosmetic outcomes by concealing the incision in the oral cavity. Methods Transoral thyroidectomy through vestibular approach was performed in two institutions on cadaveric models. Procedure was performed endoscopically in one institution, while the robotic technique was utilized at the other. Results Transoral thyroidectomy was successfully performed at both institutions with robotic and endoscopic techniques. All vital structures were identified and preserved. Conclusions Transoral thyroidectomy has been performed in animal and cadaveric models, as well as in some clinical studies. Our initial experience indicates the feasibility of this approach. More clinical studies are required to elucidate its full utility. PMID:29302476

Improvements in approaches to forecasting and evaluation techniques

NASA Astrophysics Data System (ADS)

Weatherhead, Elizabeth

2014-05-01

The US is embarking on an experiment to make significant and sustained improvements in weather forecasting. The effort stems from a series of community conversations that recognized the rapid advancements in observations, modeling and computing techniques in the academic, governmental and private sectors. The new directions and initial efforts will be summarized, including information on possibilities for international collaboration. Most new projects are scheduled to start in the last half of 2014. Several advancements include ensemble forecasting with global models, and new sharing of computing resources. Newly developed techniques for evaluating weather forecast models will be presented in detail. The approaches use statistical techniques that incorporate pair-wise comparisons of forecasts with observations and account for daily auto-correlation to assess appropriate uncertainty in forecast changes. Some of the new projects allow for international collaboration, particularly on the research components of the projects.

Laparoscopic surgical skills training: an investigation of the potential of using surgeons' visual search behaviour as a performance indicator

NASA Astrophysics Data System (ADS)

Chen, Yan; Dong, Leng; Gale, Alastair G.; Rees, Benjamin; Maxwell-Armstrong, Charles

2014-03-01

Laparoscopic surgery is a difficult perceptual-motor task and effective and efficient training in the technique is important. Viewing previously recorded laparoscopic operations is a possible available training technique for surgeons to increase their knowledge of such minimal access surgery (MAS). It is not well known whether this is a useful technique, how effective it is or what effect it has on the surgeon watching the recorded video. As part of an on-going series of studies into laparoscopic surgery, an experiment was conducted to examine whether surgical skill level has an effect on the visual search behaviour of individuals of different surgical experience when they examine such imagery. Medically naive observers, medical students, junior surgeons and experienced surgeons viewed a laparoscopic recording of a recent operation. Initial examination of the recorded eye movement data indicated commonalities between all observers, largely irrespective of surgical experience. This, it is argued, is due to visual search in this situation largely being driven by the dynamic nature of the images. The data were then examined in terms of surgical steps and also in terms of interventions when differences were found related to surgical experience. Consequently, it is argued that monitoring the eye movements of trainee surgeons whilst they watch pre-recorded operations is a potential useful adjunct to existing training regimes.

Plot-scale field experiment of surface hydrologic processes with EOS implications

NASA Technical Reports Server (NTRS)

Laymon, Charles A.; Macari, Emir J.; Costes, Nicholas C.

1992-01-01

Plot-scale hydrologic field studies were initiated at NASA Marshall Space Flight Center to a) investigate the spatial and temporal variability of surface and subsurface hydrologic processes, particularly as affected by vegetation, and b) develop experimental techniques and associated instrumentation methodology to study hydrologic processes at increasingly large spatial scales. About 150 instruments, most of which are remotely operated, have been installed at the field site to monitor ground atmospheric conditions, precipitation, interception, soil-water status, and energy flux. This paper describes the nature of the field experiment, instrumentation and sampling rationale, and presents preliminary findings.

Prediction and measurement of radiation damage to CMOS devices on board spacecraft

NASA Technical Reports Server (NTRS)

Cliff, R. A.; Danchenko, V.; Stassinopoulos, E. G.; Sing, M.; Brucker, G. J.; Ohanian, R. S.

1976-01-01

The initial results obtained from the Complementary Metal Oxide Semiconductors Radiation Effects Measurement experiment are presented. Predictions of radiation damage to C-MOS devices are based on standard environment models and computational techniques. A comparison of the shifts in CMOS threshold potentials, that is, those measured in space to those obtained from the on the ground simulation experiment with Co 60, indicated that the measured space damage is greater than predicted by a factor of two for shields thicker than 100 mils (2.54 mm), but agrees well with predictions for the thinner shields.

Effect of impurities on optical properties of pentaerythritol tetranitrate

NASA Astrophysics Data System (ADS)

Tsyshevskiy, Roman; Sharia, Onise; Kuklja, Maija M.

2012-03-01

Despite numerous efforts, the electronic nature of initiation of high explosives to detonation in general and mechanisms of their sensitivity to laser initiation in particular are far from being completely understood. Recent experiments show that Nd:YAG laser irradiation (at 1064nm) causes resonance explosive decomposition of PETN samples. In an attempt to shed some light on electronic excitations and to develop a rigorous interpretation to these experiments, the electronic structure and optical properties of PETN and a series of common impurities were studied. Band gaps (S0→S1) and optical singlet-triplet (S0→T1) transitions in both an ideal material and PETN containing various defects were simulated by means of state-of-the-art quantum-chemical computational techniques. It was shown that the presence of impurities in the PETN crystal causes significant narrowing of the band gap. The structure and role of molecular excitons in PETN are discussed.

Initiation of oncogenic transformation in human mammary epithelial cells by charged particles

NASA Technical Reports Server (NTRS)

Yang, T. C.; Georgy, K. A.; Craise, L. M.; Durante, M.

1997-01-01

Experimental studies have shown that high linear-energy transfer (LET) charged particles can be more effective than x-rays and gamma-rays in inducing oncogenic transformation in cultured cells and tumors in animals. Based on these results, experiments were designed and performed with an immortal human mammary epithelial cell line (H184B5), and several clones transformed by heavy ions were obtained. Cell fusion experiments were subsequently done, and results indicate that the transforming gene(s) is recessive. Chromosome analysis with fluorescence in situ hybridization (FISH) techniques also showed additional translocations in transformed human mammary epithelial cells. In addition, studies with these cell lines indicate that heavy ions can effectively induce deletion, break, and dicentrics. Deletion of tumor suppressor gene(s) and/or formation of translocation through DNA double strand breaks is a likely mechanism for the initiation of oncogenic transformation in human mammary epithelial cells.

Teaching severely multihandicapped students to put on their own hearing aids.

PubMed Central

Tucker, D J; Berry, G W

1980-01-01

Two experiments were conducted with six severely multihandicapped students with hearing impairments to: (a) train the six students to put on their own hearing aids independently, and (b) provide an empirical evaluation of a comprehensive instructional program for putting on a hearing aid by assessing acquisition, maintenance, and generalization of that skill across environments. All six students acquired the skill rapidly, with two students requiring remedial training on one step of the program. Because for two of the original three students the newly learned skill failed initially to generalize to other environments, a second experiment was initiated to assess generalization across environments as well as to replicate the efficiency of the acquisition program. When a variation of the multiple-probe baseline technique was used, the behavior of three additional students generalized to other settings without direct training in those settings. PMID:6444931

Stable aesthetic standards delusion: changing 'artistic quality' by elaboration.

PubMed

Carbon, Claus-Christian; Hesslinger, Vera M

2014-01-01

The present study challenges the notion that judgments of artistic quality are based on stable aesthetic standards. We propose that such standards are a delusion and that judgments of artistic quality are the combined result of exposure, elaboration, and discourse. We ran two experiments using elaboration tasks based on the repeated evaluation technique in which different versions of the Mona Lisa had to be elaborated deeply. During the initial task either the version known from the Louvre or an alternative version owned by the Prado was elaborated; during the second task both versions were elaborated in a comparative fashion. After both tasks multiple blends of the two versions had to be evaluated concerning several aesthetic key variables. Judgments of artistic quality of the blends were significantly different depending on the initially elaborated version of the Mona Lisa, indicating experience-based aesthetic processing, which contradicts the notion of stable aesthetic standards.

Robotic resections in hepatobiliary oncology - initial experience with Xi da Vinci system in India.

PubMed

Chandarana, M; Patkar, S; Tamhankar, A; Garg, S; Bhandare, M; Goel, M

2017-01-01

Minimal invasive surgery has proven its advantages over open surgeries in the perioperative period. Food and Drug Administration approved da Vinci robot in 2000. The latest version, da Vinci Xi system has a mobile tower-based robot with several modifications to improve the functionality, versatility, and operative ease. None of the centers have reported exclusively on hepatobiliary oncology using the da Vinci Xi system. We report our initial experience. To study the feasibility, advantages, and discuss the operative technique of da Vinci Xi system in hepatobiliary oncology. Data were analyzed retrospectively from a prospectively maintained database from June 2015 to October 2016. Twenty-five patients with suspected or proven hepatobiliary malignancies were operated. Total robotic technique using da Vinci Xi system was used. Demographic details and perioperative outcomes were noted. Of the 25 surgeries, 14 patients had a suspected gallbladder malignancy, 11 patients had primary or metastatic liver tumor. Median age was 53 years. The average duration of surgery was 225 min with a median blood loss 150 ml. The median postoperative stay was 4 days. The median nodal yield for radical cholecystectomy was seven. Five patients required conversion. Two of these developed postoperative morbidity. Robotic surgery for hepatobiliary oncology is feasible and can be performed safely in experienced hands. Increasing experience in this field may equal or even prove advantageous over conventional or laparoscopic approach in future. A cautious approach with judicious patient selection is the key to establishing robotic surgery as a standard surgical approach.

High temperature measurement of water vapor absorption

NASA Technical Reports Server (NTRS)

Keefer, Dennis; Lewis, J. W. L.; Eskridge, Richard

1985-01-01

An investigation was undertaken to measure the absorption coefficient, at a wavelength of 10.6 microns, for mixtures of water vapor and a diluent gas at high temperature and pressure. The experimental concept was to create the desired conditions of temperature and pressure in a laser absorption wave, similar to that which would be created in a laser propulsion system. A simplified numerical model was developed to predict the characteristics of the absorption wave and to estimate the laser intensity threshold for initiation. A non-intrusive method for temperature measurement utilizing optical laser-beam deflection (OLD) and optical spark breakdown produced by an excimer laser, was thoroughly investigated and found suitable for the non-equilibrium conditions expected in the wave. Experiments were performed to verify the temperature measurement technique, to screen possible materials for surface initiation of the laser absorption wave and to attempt to initiate an absorption wave using the 1.5 kW carbon dioxide laser. The OLD technique was proven for air and for argon, but spark breakdown could not be produced in helium. It was not possible to initiate a laser absorption wave in mixtures of water and helium or water and argon using the 1.5 kW laser, a result which was consistent with the model prediction.

Investigation of crew motion disturbances on Skylab-Experiment T-013. [for future manned spacecraft design

NASA Technical Reports Server (NTRS)

Conway, B. A.

1974-01-01

Astronaut crew motions can produce some of the largest disturbances acting on a manned spacecraft which can affect vehicle attitude and pointing. Skylab Experiment T-013 was developed to investigate the magnitude and effects of some of these disturbances on the Skylab spacecraft. The methods and techniques used to carry out this experiment are discussed, and preliminary results of data analysis presented. Initial findings indicate that forces on the order of 300 N were exerted during vigorous soaring activities, and that certain experiment activities produced spacecraft angular rate excursions 0.03 to 0.07 deg/sec. Results of Experiment T-013 will be incorporated into mathematical models of crew-motion disturbances, and are expected to be of significant aid in the sizing, design, and analysis of stabilization and control systems for future manned spacecraft.

First measurement of proton's charge form factor at very low Q2 with initial state radiation

NASA Astrophysics Data System (ADS)

Mihovilovič, M.; Weber, A. B.; Achenbach, P.; Beranek, T.; Beričič, J.; Bernauer, J. C.; Böhm, R.; Bosnar, D.; Cardinali, M.; Correa, L.; Debenjak, L.; Denig, A.; Distler, M. O.; Esser, A.; Ferretti Bondy, M. I.; Fonvieille, H.; Friedrich, J. M.; Friščić, I.; Griffioen, K.; Hoek, M.; Kegel, S.; Kohl, Y.; Merkel, H.; Middleton, D. G.; Müller, U.; Nungesser, L.; Pochodzalla, J.; Rohrbeck, M.; Sánchez Majos, S.; Schlimme, B. S.; Schoth, M.; Schulz, F.; Sfienti, C.; Širca, S.; Štajner, S.; Thiel, M.; Tyukin, A.; Vanderhaeghen, M.; Weinriefer, M.

2017-08-01

We report on a new experimental method based on initial-state radiation (ISR) in e-p scattering, which exploits the radiative tail of the elastic peak to study the properties of electromagnetic processes and to extract the proton charge form factor (GEp) at extremely small Q2. The ISR technique was implemented in an experiment at the three-spectrometer facility of the Mainz Microtron (MAMI). This led to a precise validation of radiative corrections far away from elastic line and provided first measurements of GEp for 0.001 ≤Q2 ≤ 0.004(GeV / c)2.

Can tutoring improve performance on a reasoning task under deadline conditions?

PubMed

Osman, Magda

2007-03-01

The present study examined the effectiveness of a tutoring technique that has been used to identify and address participants' misunderstandings in Wason's selection task. In particular, the study investigated whether the technique would lead to improvements in performance when the task was presented in a deadline format (a condition in which time restrictions are imposed). In Experiment 1, the effects of tutoring on performance were compared in free time (conditions in which no time restrictions are imposed) and deadline task formats. In Experiment 2, improvements in performance were studied in deadline task formats, in which the tutoring and test phases were separated by an interval of 1 day. The results suggested that tutoring improved performance on the selection task under deadline and in free time conditions. Additionally, the study showed that participants made errors because they had misinterpreted the task. With tutoring, they were able to modify their initial misunderstandings.

Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors

PubMed Central

Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

2016-01-01

The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented. PMID:26891305

Design, Fabrication and Levitation Experiments of a Micromachined Electrostatically Suspended Six-Axis Accelerometer

PubMed Central

Cui, Feng; Liu, Wu; Chen, Wenyuan; Zhang, Weiping; Wu, Xiaosheng

2011-01-01

A micromachined electrostatically suspended six-axis accelerometer, with a square plate as proof mass housed by a top stator and bottom stator, is presented. The device structure and related techniques concerning its operating principles, such as calculation of capacitances and electrostatic forces/moments, detection and levitation control of the proof mass, acceleration measurement, and structural parameters design, are described. Hybrid MEMS manufacturing techniques, including surface micromachining fabrication of thin film electrodes and interconnections, integration fabrication of thick nickel structures about 500 μm using UV-LIGA by successful removal of SU-8 photoresist mold, DRIE of silicon proof mass in thickness of 450 μm, microassembly and solder bonding, were employed to fabricate this prototype microdevice. A levitation experiment system for the fabricated microaccelerometer chip is introduced, and levitation results show that fast initial levitation within 10 ms and stable full suspension of the proof mass have been successfully demonstrated. PMID:22247662

In-line monitoring of Li-ion battery electrode porosity and areal loading using active thermal scanning - modeling and initial experiment

DOE PAGES

Rupnowski, Przemyslaw; Ulsh, Michael J.; Sopori, Bhushan; ...

2017-08-18

This work focuses on a new technique called active thermal scanning for in-line monitoring of porosity and areal loading of Li-ion battery electrodes. In this technique a moving battery electrode is subjected to thermal excitation and the induced temperature rise is monitored using an infra-red camera. Static and dynamic experiments with speeds up to 1.5 m min -1 are performed on both cathodes and anodes and a combined micro- and macro-scale finite element thermal model of the system is developed. It is shown experimentally and through simulations that during thermal scanning the temperature profile generated in an electrode depends onmore » both coating porosity (or area loading) and thickness. Here, it is concluded that by inverting this relation the porosity (or areal loading) can be determined, if thermal response and thickness are simultaneously measured.« less

In-line monitoring of Li-ion battery electrode porosity and areal loading using active thermal scanning - modeling and initial experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rupnowski, Przemyslaw; Ulsh, Michael J.; Sopori, Bhushan

This work focuses on a new technique called active thermal scanning for in-line monitoring of porosity and areal loading of Li-ion battery electrodes. In this technique a moving battery electrode is subjected to thermal excitation and the induced temperature rise is monitored using an infra-red camera. Static and dynamic experiments with speeds up to 1.5 m min -1 are performed on both cathodes and anodes and a combined micro- and macro-scale finite element thermal model of the system is developed. It is shown experimentally and through simulations that during thermal scanning the temperature profile generated in an electrode depends onmore » both coating porosity (or area loading) and thickness. Here, it is concluded that by inverting this relation the porosity (or areal loading) can be determined, if thermal response and thickness are simultaneously measured.« less

Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors.

PubMed

Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

2016-02-16

The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented.

Wind shear predictive detector technology study status

NASA Technical Reports Server (NTRS)

Gandolfi, C.

1990-01-01

Among the different elements to be investigated when considering the Wind Shear hazard, the Aeronautical Navigation Technical Service (STNA/3E), whose task is to participate in the development of new technologies and equipments, focused its effort on airborne and ground sensors for the detection of low-level wind shear. The first task, initiated in 1986, consists in the evaluation of three candidate techniques for forward-looking sensors: lidar, sodar, and radar. No development is presently foreseen for an infrared based air turbulence advance warning system although some flight experiments took place in the 70's. A Thomson infrared radiometer was then installed on an Air France Boeing 707 to evaluate its capability of detecting clear air turbulence. The conclusion showed that this technique was apparently able to detect cloud layers but that additional experiments were needed; on the other hand, the rarity of the phenomenon and the difficulty in operating on a commercial aircraft were also mentioned.

In-line monitoring of Li-ion battery electrode porosity and areal loading using active thermal scanning - modeling and initial experiment

NASA Astrophysics Data System (ADS)

Rupnowski, Przemyslaw; Ulsh, Michael; Sopori, Bhushan; Green, Brian G.; Wood, David L.; Li, Jianlin; Sheng, Yangping

2018-01-01

This work focuses on a new technique called active thermal scanning for in-line monitoring of porosity and areal loading of Li-ion battery electrodes. In this technique a moving battery electrode is subjected to thermal excitation and the induced temperature rise is monitored using an infra-red camera. Static and dynamic experiments with speeds up to 1.5 m min-1 are performed on both cathodes and anodes and a combined micro- and macro-scale finite element thermal model of the system is developed. It is shown experimentally and through simulations that during thermal scanning the temperature profile generated in an electrode depends on both coating porosity (or area loading) and thickness. It is concluded that by inverting this relation the porosity (or areal loading) can be determined, if thermal response and thickness are simultaneously measured.

Enhanced Attitude Control Experiment for SSTI Lewis Spacecraft

NASA Technical Reports Server (NTRS)

Maghami, Peoman G.

1997-01-01

The enhanced attitude control system experiment is a technology demonstration experiment on the NASA's small spacecraft technology initiative program's Lewis spacecraft to evaluate advanced attitude control strategies. The purpose of the enhanced attitude control system experiment is to evaluate the feasibility of designing and implementing robust multi-input/multi-output attitude control strategies for enhanced pointing performance of spacecraft to improve the quality of the measurements of the science instruments. Different control design strategies based on modern and robust control theories are being considered for the enhanced attitude control system experiment. This paper describes the experiment as well as the design and synthesis of a mixed H(sub 2)/H(sub infinity) controller for attitude control. The control synthesis uses a nonlinear programming technique to tune the controller parameters and impose robustness and performance constraints. Simulations are carried out to demonstrate the feasibility of the proposed attitude control design strategy. Introduction

Dynamic Failure of Materials. Volume 1 - Experiments and Analyses

DTIC Science & Technology

1998-11-01

initial increments of voids do not lead to substantial relaxation of stress. In this case, the condition (8.1) gives Vv = Ao- aVv * ß=— (8.10) pc...enough strain steps to define the process accurately. At each strain step, a combined Newton-Raphson and regulafalsi solution technique (multiple trials ...laser surgery. Clinical studies have demonstrated that, for some applications, surgical lasers are superior to conventional surgical procedures

Sebastien Philippe Discusses the Zero-Knowledge Protocol

ScienceCinema

Philippe, Sebastien

2018-06-12

A system that can compare physical objects while potentially protecting sensitive information about the objects themselves has been demonstrated experimentally at the U.S. Department of Energy’s (DOE) Princeton Plasma Physics Laboratory (PPPL). This work, by researchers at Princeton University and PPPL, marks an initial confirmation of the application of a powerful cryptographic technique in the physical world. Graduate student Sébastien Philippe discusses the experiment.

Phase separation kinetics in immiscible liquids

NASA Technical Reports Server (NTRS)

Ng, Lee H.; Sadoway, Donald R.

1987-01-01

The kinetics of phase separation in the succinonitrile-water system are being investigated. Experiments involve initial physical mixing of the two immiscible liquids at a temperature above the consolute, decreasing the temperature into the miscibility gap, followed by iamging of the resultant microstructure as it evolves with time. Refractive index differences allow documentation of the changing microstructures by noninvasive optical techniques without the need to quench the liquid structures for analysis.

Phase separation kinetics in immiscible liquids

NASA Technical Reports Server (NTRS)

Sadoway, D. R.

1986-01-01

The kinetics of phase separation in the succinonitrile-water system are being investigated. Experiments involve initial physical mixing of the two immiscible liquids at a temperature above the consolute, decreasing the temperature into the miscibility gap, followed by imaging of the resultant microstructure as it evolves with time. Refractive index differences allow documentation of the changing microstructures by noninvasive optical techniques without the need to quench the liquid structures for analysis.

Seeding the initial population with feasible solutions in metaheuristic optimization of steel trusses

NASA Astrophysics Data System (ADS)

Kazemzadeh Azad, Saeid

2018-01-01

In spite of considerable research work on the development of efficient algorithms for discrete sizing optimization of steel truss structures, only a few studies have addressed non-algorithmic issues affecting the general performance of algorithms. For instance, an important question is whether starting the design optimization from a feasible solution is fruitful or not. This study is an attempt to investigate the effect of seeding the initial population with feasible solutions on the general performance of metaheuristic techniques. To this end, the sensitivity of recently proposed metaheuristic algorithms to the feasibility of initial candidate designs is evaluated through practical discrete sizing of real-size steel truss structures. The numerical experiments indicate that seeding the initial population with feasible solutions can improve the computational efficiency of metaheuristic structural optimization algorithms, especially in the early stages of the optimization. This paves the way for efficient metaheuristic optimization of large-scale structural systems.

An artificial-intelligence technique for qualitatively deriving enzyme kinetic mechanisms from initial-velocity measurements and its application to hexokinase.

PubMed Central

Garfinkel, L; Cohen, D M; Soo, V W; Garfinkel, D; Kulikowski, C A

1989-01-01

We have developed a computer method based on artificial-intelligence techniques for qualitatively analysing steady-state initial-velocity enzyme kinetic data. We have applied our system to experiments on hexokinase from a variety of sources: yeast, ascites and muscle. Our system accepts qualitative stylized descriptions of experimental data, infers constraints from the observed data behaviour and then compares the experimentally inferred constraints with corresponding theoretical model-based constraints. It is desirable to have large data sets which include the results of a variety of experiments. Human intervention is needed to interpret non-kinetic information, differences in conditions, etc. Different strategies were used by the several experimenters whose data was studied to formulate mechanisms for their enzyme preparations, including different methods (product inhibitors or alternate substrates), different experimental protocols (monitoring enzyme activity differently), or different experimental conditions (temperature, pH or ionic strength). The different ordered and rapid-equilibrium mechanisms proposed by these experimenters were generally consistent with their data. On comparing the constraints derived from the several experimental data sets, they are found to be in much less disagreement than the mechanisms published, and some of the disagreement can be ascribed to different experimental conditions (especially ionic strength). PMID:2690819

Initial experience of a novel sheath guide for transbrachial coil embolization of cerebral aneurysms in the anterior cerebral circulation.

PubMed

Iwata, Tomonori; Mori, Takahisa; Tajiri, Hiroyuki; Miyazaki, Yuichi; Nakazaki, Masahito; Mizokami, Koji

2013-03-01

The transfemoral approach is a common technique for coil embolization of cerebral aneurysms in the anterior cerebral circulation. However, it is difficult to advance a guiding catheter into the carotid artery via the femoral route in patients with a tortuous aortic arch, an unfavorable supra-aortic takeoff, aortic diseases, or occlusion of the femoral artery. To report our initial experiences of coil embolization of cerebral aneurysms in the anterior cerebral circulation with a novel sheath guide for transbrachial carotid cannulation. A sheath guide designed specifically for transbrachial carotid cannulation was developed; transbrachial coil embolization for cerebral aneurysms began in May 2011. Included for analysis were patients who underwent transbrachial coil embolization for cerebral aneurysms in the anterior cerebral circulation from May 2011 to January 2012. Adjuvant techniques, angiographic results, procedural success, and periprocedural complications were investigated. Ten patients underwent transbrachial coil embolization of cerebral aneurysms in the anterior cerebral circulation. All procedures were successful using the brachial route. No periprocedural complications occurred. Patients were permitted to get seated immediately after coil embolization even during hemostasis. The sheath guide specifically designed for transbrachial carotid cannulation was useful for coil embolization of cerebral aneurysms in the anterior cerebral circulation.

Complex traumatic posterior urethral strictures.

PubMed

Turner-Warwick, R

1976-01-01

A distinction between simple and complex posterior urethral strictures is proposed. The development of a complex stricture, requiring an extensive transpubic repair, must be regarded as a less than admirable result of the initial treatment, even if it is occasionally inevitable. However, it is particularly important that our endeavors to improve the end result of the relatively rare severe urethral injuries should not result in over-management of the relatively minor injuries, since this could increase the stricture potential of many. Therefore, we must keep our over-all concepts of the initial management of urethral injuries under careful review. Posterior urethroplasty should be regarded as a specialist procedure. It can be made to appear beguilingly simple but it cannot be recommended for occasional or general use. Even the relatively simple free patch graft technique is inadvisable for use in the sphincter area for surgeons who do not have considerable experience of it in the relatively forgiving bulbourethral area. The results of repair of posterior urethral strictures, even the complex ones, by anastomotic procedures can be excellent but real competence depends upon a particular aptitude of the surgeon for the minutiae of reconstructive techniques, appropriate training in a specializing department, a real ongoing numerical experience and special instrumentation with facilities for detailed urodynamic evaluation of this sphincter active area of the urethra.

Non-vascularized free toe phalanx transfers in congenital hand deformities--the Great Ormond Street experience.

PubMed

Cavallo, A V; Smith, P J; Morley, S; Morsi, A W

2003-12-01

Many options of varying complexity are available for the management of congenital short digits resulting from aphalangia in symbrachydactyly and constriction ring syndrome. We have used non-vascularized free toe phalanx transfers for these children when a vascularized toe transfer has been contraindicated. We describe our technique and experience with 22 children who underwent a total of 64 transfers of the proximal (35) or middle (29) toe phalanges (average 3 per child). The mean age at initial surgery was 15 months, and the mean follow-up was 5 years. Duration of time until epiphyseal closure could not be determined accurately, but total digital elongation averaged 6mm. Complications of this technique include joint instability, premature epiphyseal closure and, in one patient, infection and graft loss. Donor site deformity was determined according to measured growth deficit and toe function. This technique is a simple option for digital elongation and, if performed in the appropriate age group in short fingered and monodactylous subtypes of symbrachydactyly, has the potential to allow growth and function with minimal donor site deficit.

Retrieval of Dry Snow Parameters from Radiometric Data Using a Dense Medium Model and Genetic Algorithms

NASA Technical Reports Server (NTRS)

Tedesco, Marco; Kim, Edward J.

2005-01-01

In this paper, GA-based techniques are used to invert the equations of an electromagnetic model based on Dense Medium Radiative Transfer Theory (DMRT) under the Quasi Crystalline Approximation with Coherent Potential to retrieve snow depth, mean grain size and fractional volume from microwave brightness temperatures. The technique is initially tested on both noisy and not-noisy simulated data. During this phase, different configurations of genetic algorithm parameters are considered to quantify how their change can affect the algorithm performance. A configuration of GA parameters is then selected and the algorithm is applied to experimental data acquired during the NASA Cold Land Process Experiment. Snow parameters retrieved with the GA-DMRT technique are then compared with snow parameters measured on field.

No patch technique for complete atrioventricular canal repair.

PubMed

Aramendi, José Ignacio; Rodriguez, Miguel Angel; Luis, Teresa; Voces, Roberto

2006-08-01

We describe our initial experience with a new technique, consisting in direct closure of the ventricular septal defect component of the AV canal, by directly attaching the common bridging leaflets to the crest of the ventricular septum with interrupted sutures. After closure of the cleft, the ostium primum defect was closed with a running suture suturing the border of the septum primum to the newly created AV valve annulus. Three patients were operated upon. There was no mortality. Mean ischemic time was 39 min and mean pump time 77 min. All patients remained in sinus rhythm. At follow-up only trivial or mild mitral regurgitation was observed. This new technique permits the repair of complete AV canal without the need for any patch. It is fast, simple and reproducible.

The suspension (Frost) suture: experience and applications.

PubMed

Connolly, Karen L; Albertini, John G; Miller, Christopher J; Ozog, David M

2015-03-01

The Frost suture is a well-known surgical technique for providing upward tension on the lower lid to prevent or correct ectropion after surgical interventions in the periorbital area. Despite its relatively common use, comprehensive information on executing this technique is not readily available. To review eyelid anatomy, indications, and proper technique for performing the Frost suture, as well as potential complications. A review of the literature on Frost sutures was performed. Cadaveric dissection was performed to demonstrate placement of the Frost suture. The Frost suture is a useful method to reduce the risk of ectropion after surgery near the lower eyelid. Downward pull on the lid can occur with normal wound contracture even if ectropion is not present with the initial repair, reinforcing the need for preventive measures. Potential complications of this technique include superficial skin erosion of the upper lid, corneal abrasion, and blockage of the field of vision while the suture is in place.

Evaluating the performance of vehicular platoon control under different network topologies of initial states

NASA Astrophysics Data System (ADS)

Li, Yongfu; Li, Kezhi; Zheng, Taixiong; Hu, Xiangdong; Feng, Huizong; Li, Yinguo

2016-05-01

This study proposes a feedback-based platoon control protocol for connected autonomous vehicles (CAVs) under different network topologies of initial states. In particularly, algebraic graph theory is used to describe the network topology. Then, the leader-follower approach is used to model the interactions between CAVs. In addition, feedback-based protocol is designed to control the platoon considering the longitudinal and lateral gaps simultaneously as well as different network topologies. The stability and consensus of the vehicular platoon is analyzed using the Lyapunov technique. Effects of different network topologies of initial states on convergence time and robustness of platoon control are investigated. Results from numerical experiments demonstrate the effectiveness of the proposed protocol with respect to the position and velocity consensus in terms of the convergence time and robustness. Also, the findings of this study illustrate the convergence time of the control protocol is associated with the initial states, while the robustness is not affected by the initial states significantly.

'Enzyme Test Bench': A biochemical application of the multi-rate modeling

NASA Astrophysics Data System (ADS)

Rachinskiy, K.; Schultze, H.; Boy, M.; Büchs, J.

2008-11-01

In the expanding field of 'white biotechnology' enzymes are frequently applied to catalyze the biochemical reaction from a resource material to a valuable product. Evolutionary designed to catalyze the metabolism in any life form, they selectively accelerate complex reactions under physiological conditions. Modern techniques, such as directed evolution, have been developed to satisfy the increasing demand on enzymes. Applying these techniques together with rational protein design, we aim at improving of enzymes' activity, selectivity and stability. To tap the full potential of these techniques, it is essential to combine them with adequate screening methods. Nowadays a great number of high throughput colorimetric and fluorescent enzyme assays are applied to measure the initial enzyme activity with high throughput. However, the prediction of enzyme long term stability within short experiments is still a challenge. A new high throughput technique for enzyme characterization with specific attention to the long term stability, called 'Enzyme Test Bench', is presented. The concept of the Enzyme Test Bench consists of short term enzyme tests conducted under partly extreme conditions to predict the enzyme long term stability under moderate conditions. The technique is based on the mathematical modeling of temperature dependent enzyme activation and deactivation. Adapting the temperature profiles in sequential experiments by optimum non-linear experimental design, the long term deactivation effects can be purposefully accelerated and detected within hours. During the experiment the enzyme activity is measured online to estimate the model parameters from the obtained data. Thus, the enzyme activity and long term stability can be calculated as a function of temperature. The results of the characterization, based on micro liter format experiments of hours, are in good agreement with the results of long term experiments in 1L format. Thus, the new technique allows for both: the enzyme screening with regard to the long term stability and the choice of the optimal process temperature. The presented article gives a successful example for the application of multi-rate modeling, experimental design and parameter estimation within biochemical engineering. At the same time, it shows the limitations of the methods at the state of the art and addresses the current problems to the applied mathematics community.

Alternative Approaches to Land Initialization for Seasonal Precipitation and Temperature Forecasts

NASA Technical Reports Server (NTRS)

Koster, Randal; Suarez, Max; Liu, Ping; Jambor, Urszula

2004-01-01

The seasonal prediction system of the NASA Global Modeling and Assimilation Office is used to generate ensembles of summer forecasts utilizing realistic soil moisture initialization. To derive the realistic land states, we drive offline the system's land model with realistic meteorological forcing over the period 1979-1993 (in cooperation with the Global Land Data Assimilation System project at GSFC) and then extract the state variables' values on the chosen forecast start dates. A parallel series of forecast ensembles is performed with a random (though climatologically consistent) set of land initial conditions; by comparing the two sets of ensembles, we can isolate the impact of land initialization on forecast skill from that of the imposed SSTs. The base initialization experiment is supplemented with several forecast ensembles that use alternative initialization techniques. One ensemble addresses the impact of minimizing climate drift in the system through the scaling of the initial conditions, and another is designed to isolate the importance of the precipitation signal from that of all other signals in the antecedent offline forcing. A third ensemble includes a more realistic initialization of the atmosphere along with the land initialization. The impact of each variation on forecast skill is quantified.

Reconstruction of Atmospheric Tracer Releases with Optimal Resolution Features: Concentration Data Assimilation

NASA Astrophysics Data System (ADS)

Singh, Sarvesh Kumar; Turbelin, Gregory; Issartel, Jean-Pierre; Kumar, Pramod; Feiz, Amir Ali

2015-04-01

The fast growing urbanization, industrialization and military developments increase the risk towards the human environment and ecology. This is realized in several past mortality incidents, for instance, Chernobyl nuclear explosion (Ukraine), Bhopal gas leak (India), Fukushima-Daichi radionuclide release (Japan), etc. To reduce the threat and exposure to the hazardous contaminants, a fast and preliminary identification of unknown releases is required by the responsible authorities for the emergency preparedness and air quality analysis. Often, an early detection of such contaminants is pursued by a distributed sensor network. However, identifying the origin and strength of unknown releases following the sensor reported concentrations is a challenging task. This requires an optimal strategy to integrate the measured concentrations with the predictions given by the atmospheric dispersion models. This is an inverse problem. The measured concentrations are insufficient and atmospheric dispersion models suffer from inaccuracy due to the lack of process understanding, turbulence uncertainties, etc. These lead to a loss of information in the reconstruction process and thus, affect the resolution, stability and uniqueness of the retrieved source. An additional well known issue is the numerical artifact arisen at the measurement locations due to the strong concentration gradient and dissipative nature of the concentration. Thus, assimilation techniques are desired which can lead to an optimal retrieval of the unknown releases. In general, this is facilitated within the Bayesian inference and optimization framework with a suitable choice of a priori information, regularization constraints, measurement and background error statistics. An inversion technique is introduced here for an optimal reconstruction of unknown releases using limited concentration measurements. This is based on adjoint representation of the source-receptor relationship and utilization of a weight function which exhibits a priori information about the unknown releases apparent to the monitoring network. The properties of the weight function provide an optimal data resolution and model resolution to the retrieved source estimates. The retrieved source estimates are proved theoretically to be stable against the random measurement errors and their reliability can be interpreted in terms of the distribution of the weight functions. Further, the same framework can be extended for the identification of the point type releases by utilizing the maximum of the retrieved source estimates. The inversion technique has been evaluated with the several diffusion experiments, like, Idaho low wind diffusion experiment (1974), IIT Delhi tracer experiment (1991), European Tracer Experiment (1994), Fusion Field Trials (2007), etc. In case of point release experiments, the source parameters are mostly retrieved close to the true source parameters with least error. Primarily, the proposed technique overcomes two major difficulties incurred in the source reconstruction: (i) The initialization of the source parameters as required by the optimization based techniques. The converged solution depends on their initialization. (ii) The statistical knowledge about the measurement and background errors as required by the Bayesian inference based techniques. These are hypothetically assumed in case of no prior knowledge.

Nitrogen removal from digested slurries using a simplified ammonia stripping technique.

PubMed

Provolo, Giorgio; Perazzolo, Francesca; Mattachini, Gabriele; Finzi, Alberto; Naldi, Ezio; Riva, Elisabetta

2017-11-01

This study assessed a novel technique for removing nitrogen from digested organic waste based on a slow release of ammonia that was promoted by continuous mixing of the digestate and delivering a continuous air stream across the surface of the liquid. Three 10-day experiments were conducted using two 50-L reactors. In the first two, nitrogen removal efficiencies were evaluated from identical digestates maintained at different temperatures (30°C and 40°C). At the start of the first experiment, the digestates were adjusted to pH 9 using sodium hydroxide, while in the second experiment pH was not adjusted. The highest ammonia removal efficiency (87%) was obtained at 40°C with pH adjustment. However at 40°C without pH adjustment, removal efficiencies of 69% for ammonia and 47% for total nitrogen were obtained. In the third experiment two different digestates were tested at 50°C without pH adjustment. Although the initial chemical characteristics of the digestates were different in this experiment, the ammonia removal efficiencies were very similar (approximately 85%). Despite ammonia removal, the pH increased in all experiments, most likely due to carbon dioxide stripping that was promoted by temperature and mixing. The technique proved to be suitable for removing nitrogen following anaerobic digestion of livestock manure because effective removal was obtained at natural pH (≈8) and 40°C, common operating conditions at typical biogas plants that process manure. Furthermore, the electrical energy requirement to operate the process is limited (estimated to be 3.8kWhm -3 digestate). Further improvements may increase the efficiency and reduce the processing time of this treatment technique. Even without these advances slow-rate air stripping of ammonia is a viable option for reducing the environmental impact associated with animal manure management. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Joint Experiment for Crop Assessment and Monitoring (JECAM) Initiative: Developing methods and best practices for global agricultural monitoring

NASA Astrophysics Data System (ADS)

Champagne, C.; Jarvis, I.; Defourny, P.; Davidson, A.

2014-12-01

Agricultural systems differ significantly throughout the world, making a 'one size fits all' approach to remote sensing and monitoring of agricultural landscapes problematic. The Joint Experiment for Crop Assessment and Monitoring (JECAM) was established in 2009 to bring together the global scientific community to work towards a set of best practices and recommendations for using earth observation data to map, monitor and report on agricultural productivity globally across an array of diverse agricultural systems. These methods form the research and development component of the Group on Earth Observation Global Agricultural Monitoring (GEOGLAM) initiative to harmonize global monitoring efforts and increase market transparency. The JECAM initiative brings together researchers from a large number of globally distributed, well monitored agricultural test sites that cover a range of crop types, cropping systems and climate regimes. Each test site works independently as well as together across multiple sites to test methods, sensors and field data collection techniques to derive key agricultural parameters, including crop type, crop condition, crop yield and soil moisture. The outcome of this project will be a set of best practices that cover the range of remote sensing monitoring and reporting needs, including satellite data acquisition, pre-processing techniques, information retrieval and ground data validation. These outcomes provide the research and development foundation for GEOGLAM and will help to inform the development of the GEOGLAM "system of systems" for global agricultural monitoring. The outcomes of the 2014 JECAM science meeting will be discussed as well as examples of methods being developed by JECAM scientists.

High-speed multi-frame laser Schlieren for visualization of explosive events

NASA Astrophysics Data System (ADS)

Clarke, S. A.; Murphy, M. J.; Landon, C. D.; Mason, T. A.; Adrian, R. J.; Akinci, A. A.; Martinez, M. E.; Thomas, K. A.

2007-09-01

High-Speed Multi-Frame Laser Schlieren is used for visualization of a range of explosive and non-explosive events. Schlieren is a well-known technique for visualizing shock phenomena in transparent media. Laser backlighting and a framing camera allow for Schlieren images with very short (down to 5 ns) exposure times, band pass filtering to block out explosive self-light, and 14 frames of a single explosive event. This diagnostic has been applied to several explosive initiation events, such as exploding bridgewires (EBW), Exploding Foil Initiators (EFI) (or slappers), Direct Optical Initiation (DOI), and ElectroStatic Discharge (ESD). Additionally, a series of tests have been performed on "cut-back" detonators with varying initial pressing (IP) heights. We have also used this Diagnostic to visualize a range of EBW, EFI, and DOI full-up detonators. The setup has also been used to visualize a range of other explosive events, such as explosively driven metal shock experiments and explosively driven microjets. Future applications to other explosive events such as boosters and IHE booster evaluation will be discussed. Finite element codes (EPIC, CTH) have been used to analyze the schlieren images to determine likely boundary or initial conditions to determine the temporal-spatial pressure profile across the output face of the detonator. These experiments are part of a phased plan to understand the evolution of detonation in a detonator from initiation shock through run to detonation to full detonation to transition to booster and booster detonation.

Associated with aerospace vehicles development of methodologies for the estimation of thermal properties

NASA Technical Reports Server (NTRS)

Scott, Elaine P.

1994-01-01

Thermal stress analyses are an important aspect in the development of aerospace vehicles at NASA-LaRC. These analyses require knowledge of the temperature distributions within the vehicle structures which consequently necessitates the need for accurate thermal property data. The overall goal of this ongoing research effort is to develop methodologies for the estimation of the thermal property data needed to describe the temperature responses of these complex structures. The research strategy undertaken utilizes a building block approach. The idea here is to first focus on the development of property estimation methodologies for relatively simple conditions, such as isotropic materials at constant temperatures, and then systematically modify the technique for the analysis of more and more complex systems, such as anisotropic multi-component systems. The estimation methodology utilized is a statistically based method which incorporates experimental data and a mathematical model of the system. Several aspects of this overall research effort were investigated during the time of the ASEE summer program. One important aspect involved the calibration of the estimation procedure for the estimation of the thermal properties through the thickness of a standard material. Transient experiments were conducted using a Pyrex standard at various temperatures, and then the thermal properties (thermal conductivity and volumetric heat capacity) were estimated at each temperature. Confidence regions for the estimated values were also determined. These results were then compared to documented values. Another set of experimental tests were conducted on carbon composite samples at different temperatures. Again, the thermal properties were estimated for each temperature, and the results were compared with values obtained using another technique. In both sets of experiments, a 10-15 percent off-set between the estimated values and the previously determined values was found. Another effort was related to the development of the experimental techniques. Initial experiments required a resistance heater placed between two samples. The design was modified such that the heater was placed on the surface of only one sample, as would be necessary in the analysis of built up structures. Experiments using the modified technique were conducted on the composite sample used previously at different temperatures. The results were within 5 percent of those found using two samples. Finally, an initial heat transfer analysis, including conduction, convection and radiation components, was completed on a titanium sandwich structural sample. Experiments utilizing this sample are currently being designed and will be used to first estimate the material's effective thermal conductivity and later to determine the properties associated with each individual heat transfer component.

Fat grafting to the nose: personal experience with 36 patients.

PubMed

Monreal, Juan

2011-10-01

Clinicians are facing an increasing trend toward nonsurgical nose reshaping using synthetic injectables, mainly for patients who refuse standard rhinoplasties. Autologous fat grafting is a safer and convenient alternative to permanent or semipermanent injectables due to better results as well as fewer and milder side effects. The author reports his experience with fat grafting to the nose using his personal technique for 36 consecutive patients. The experience covers primary treatments of noses not treated by surgery, treatment of post rhinoplasty deformities, and combination fat grafting and rhinoplasties. The technique used by the author for fat grafting to the nose does not differ significantly from that used for other body or face areas. It is based in the atraumatic extraction of fat fragments using a multi-orifice cannula and injection of these fragments using 1.4- to 1.6-mm cannulas or needles. In combining rhinoplasties with fat grafting, fat grafts are used in the same location instead of a prosthesis or cartilage grafts. The initial analysis of postoperative results showed a good to high level of patient satisfaction, particularly in primary cases, with virtually no complications or severe side effects. Some easily corrected side effects probably were learning curve dependent. Autologous fat grafting is an effective and reliable technique for aesthetic and reconstructive nose reshaping for patients who refuse surgical treatments. Although optimal results can be achieved with this technique, they are not comparable with those obtained by surgical rhinoplasties, and this is an important issue to discuss with the prospective patient.

Promotion of family-centered birth with gentle cesarean delivery.

PubMed

Magee, Susanna R; Battle, Cynthia; Morton, John; Nothnagle, Melissa

2014-01-01

In this commentary we describe our experience developing a "gentle cesarean" program at a community hospital housing a family medicine residency program. The gentle cesarean technique has been popularized in recent obstetrics literature as a viable option to enhance the experience and outcomes of women and families undergoing cesarean delivery. Skin-to-skin placement of the infant in the operating room with no separation of mother and infant, reduction of extraneous noise, and initiation of breastfeeding in the operating room distinguish this technique from traditional cesarean delivery. Collaboration among family physicians, obstetricians, midwives, pediatricians, neonatologists, anesthesiologists, nurses, and operating room personnel facilitated the provision of gentle cesarean delivery to families requiring an operative birth. Among 144 gentle cesarean births performed from 2009 to 2012, complication rates were similar to or lower than those for traditional cesarean births. Gentle cesarean delivery is now standard of care at our institution. By sharing our experience, we hope to help other hospitals develop gentle cesarean programs. Family physicians should play an integral role in this process. © Copyright 2014 by the American Board of Family Medicine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeager, John D.; Bowden, Patrick R.; Guildenbecher, Daniel R.

The fragment impact response of two plastic-bonded explosive (PBX) formulations was studied using explosively driven aluminum fragments. A generic aluminum-capped detonator generated sub-mm aluminum particles moving at hypersonic velocities. The ability of these fragments to initiate reaction or otherwise damage two PBX materials was assessed using go/no-go experiments at standoff distances of up to 160 mm. Lower density PBX 9407 (RDX-based) was initiable at up to 115 mm, while higher density PBX 9501 (HMX-based) was only initiable at up to 6 mm. Several techniques were used to characterize the size, distribution, and velocity of the particles. Witness plate materials, includingmore » copper and polycarbonate, and backlit high speed video were used to characterize the distribution of particles, finding that the aluminum cap did not fragment homogeneously but rather with larger particles in a ring surrounding finer particles. Finally, precise digital holography experiments were conducted to measure the three-dimensional shape and size of the fastest-moving fragments, which ranged between 100 and 700 μm and traveled between 2.2 and 3.2 km/s. Crucially, these experiments showed variability in the fragmentation in terms of the number of fragments at the leading edge of the fragment field, indicating that both single and multiple shock impacts could be imparted to the target material. As a result, these types of data are critical for safety experiments and hydrocode simulations to quantify shock-to-detonation transition mechanisms and the associated risk-margins for these materials.« less

An experimental study of soil temperature regimes associated with solar disinfestation techniques under greenhouse conditions in Greece.

PubMed

Garofalakis, I; Tsiros, I; Frangoudakis, A; Chronopoulos, K; Flouri, F

2006-01-01

This paper deals with an experimental study of various techniques that have been applied for soil disinfestation purposes under greenhouse conditions. Various meteorological parameters and soil temperatures were measured for four different experimental soil segments (three associated with different disinfestation techniques and one as a reference) at depths varying between 0-1 m and with a time interval of 5 min in a greenhouse located in the Agricultural University of Athens Campus, Greece. Results showed that plastic polyethylene films such as covers, metallic conductors or a combination of both were able to enhance heat transfer and temperature increase in greenhouse soil. For typical disinfestation conditions, the depth-averaged temperature values for plastic covers, metallic conductors, and the combination of both were found to be higher than those for the reference of about 5 degrees C, 12 degrees C and 15 micro C, respectively. Moreover, the remained population percentages 50 days after the initiation of the experiment were found to be 19.3%, 25.3%, 37.3% Kcat 94% of the initial population, for the combination of metallic conductors and plastic covers, metallic conductors, plastic cover, and for the reference, respectively.

Use of the 1991 ASCOT field study data in a mesoscale model employing a four-dimensional data assimilation technique

NASA Astrophysics Data System (ADS)

Fast, Jerome D.; Osteen, B. Lance

In this study, a four-dimensional data assimilation technique based on Newtonian relaxation is incorporated into the Colorado State University (CSU) Regional Atmospheric Modeling System (RAMS) and evaluated using data taken from one experiment of the US Department of Energy's (DOE) 1991 Atmospheric Studies in COmplex Terrain (ASCOT) field study along the front range of the Rockies in Colorado. The main objective of this study is to determine the ability of the model to predict small-scale circulations influenced by terrain, such as drainage flows, and assess the impact of data assimilation on the numerical results. In contrast to previous studies in which the smallest horizontal grid spacing was 10 km and 8 km, data assimilation is applied in this study to domains with a horizontal grid spacing as small as 1 km. The prognostic forecasts made by RAMS are evaluated by comparing simulations that employ static initial conditions, with simulations that incorporate continuous data assimilation, and data assimilation for a fixed period of time (dynamic initialization). This paper will also elaborate on the application and limitation of the Newtonian relaxation technique in limited-area mesoscale models with a relatively small grid spacing.

Initiation process of a thrust fault revealed by analog experiments

NASA Astrophysics Data System (ADS)

Yamada, Yasuhiro; Dotare, Tatsuya; Adam, Juergen; Hori, Takane; Sakaguchi, Hide

2016-04-01

We conducted 2D (cross-sectional) analog experiments with dry sand using a high resolution digital image correlation (DIC) technique to reveal initiation process of a thrust fault in detail, and identified a number of "weak shear bands" and minor uplift prior to the thrust initiation. The observations suggest that the process can be divided into three stages. Stage 1: characterized by a series of abrupt and short-lived weak shear bands at the location where the thrust will be generated later. Before initiation of the fault, the area to be the hanging wall starts to uplift. Stage 2: defined by the generation of the new thrust and its active displacement. The location of the new thrust seems to be constrained by its associated back-thrust, produced at the foot of the surface slope (by the previous thrust). The activity of the previous thrust turns to zero once the new thrust is generated, but the timing of these two events is not the same. Stage 3: characterized by a constant displacement along the (new) thrust. Similar minor shear bands can be seen in the toe area of the Nankai accretionary prism, SW Japan and we can correlate the along-strike variations in seismic profiles to the model results that show the characteristic features in each thrust development stage.

Penetrator Coring Apparatus for Cometary Surfaces

NASA Technical Reports Server (NTRS)

Braun, David F.; Heinrich, Michael; Ai, Huirong Anita; Ahrens, Thomas J.

2004-01-01

Touch and go impact coring is an attractive technique for sampling cometary nuclei and asteroidal surface on account of the uncertain strength properties and low surface gravities of these objects. Initial coring experiments in low temperature (approx. 153K polycrystalline ice) and porous rock demonstrate that simultaneous with impact coring, measurements of both the penetration strength and constraints on the frictional properties of surface materials can be obtained upon core penetration and core sample extraction. The method of sampling an asteroid, to be deployed, on the now launched MUSES-C mission, employs a small gun device that fires into the asteroid and the resulted impact ejecta is collected for return to Earth. This technique is well suited for initial sampling in a very low gravity environment and deployment depends little on asteroid surface mechanical properties. Since both asteroids and comets are believed to have altered surface properties a simple sampling apparatus that preserves stratigraphic information, such as impact coring is an attractive alternate to impact ejecta collection.

Modeling target normal sheath acceleration using handoffs between multiple simulations

NASA Astrophysics Data System (ADS)

McMahon, Matthew; Willis, Christopher; Mitchell, Robert; King, Frank; Schumacher, Douglass; Akli, Kramer; Freeman, Richard

2013-10-01

We present a technique to model the target normal sheath acceleration (TNSA) process using full-scale LSP PIC simulations. The technique allows for a realistic laser, full size target and pre-plasma, and sufficient propagation length for the accelerated ions and electrons. A first simulation using a 2D Cartesian grid models the laser-plasma interaction (LPI) self-consistently and includes field ionization. Electrons accelerated by the laser are imported into a second simulation using a 2D cylindrical grid optimized for the initial TNSA process and incorporating an equation of state. Finally, all of the particles are imported to a third simulation optimized for the propagation of the accelerated ions and utilizing a static field solver for initialization. We also show use of 3D LPI simulations. Simulation results are compared to recent ion acceleration experiments using SCARLET laser at The Ohio State University. This work was performed with support from ASOFR under contract # FA9550-12-1-0341, DARPA, and allocations of computing time from the Ohio Supercomputing Center.

Application of wire beam electrode technique to investigate initiation and propagation of rebar corrosion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Wei; Dong, Ze Hua, E-mail: zehua.dong@gmail.com; Kong, De Jie

Multi-electrode technique named as wire beam electrode (WBE) was used to study pitting corrosion of rebar under concrete cover. When WBE embedded mortar sample was immersed in NaCl solution, uneven distributions of galvanic current and open circuit potential (OCP) on the WBE were observed due to the initiation of pitting corrosion. The following oxygen depletion in mortar facilitated the negative shift of the OCP and the smoothing of the current and potential distributions. Wetting–drying cycle experiments showed that corrosion products instead of oxygen in wet mortar specimen sustained the propagation of pitting corrosion due to Fe (III) taking part inmore » cathodic depolarization during oxygen-deficient wet period, which was confirmed by micro-Raman spectroscopy. In addition, new pitting corrosion occurred mainly near the corrosion products, leading to preferentially horizontal propagation of rust layer on the WBE. A localized corrosion factor was further presented to quantify the localised corrosion based on galvanic current maps.« less

Hollow cathode startup using a microplasma discharge

NASA Technical Reports Server (NTRS)

Aston, G.

1981-01-01

Attention is given to a microplasma discharge to initiate a hollow cathode discharge for such applications as plasma flow experiments, the electric propulsion of space vehicles, and as a replacement for filament cathodes in neutral beam injector ion sources. The technique results in a cathode that is easy to start, simple in design, and which does not require external RF exciters, inserts or heating elements. Future applications may include ion beam milling and ion implantation.

Results of FM-TV threshold reduction investigation for the ATS F trust experiment

NASA Technical Reports Server (NTRS)

Brown, J. P.

1972-01-01

An investigation of threshold effects in FM TV was initiated to determine if any simple, low cost techniques were available which can reduce the subjective video threshold, applicable to low cost community TV reception via satellite. Two methods of eliminating these effects were examined: the use of standard video pre-emphasis, and the use of an additional circuit to blank the picture tube during the retrace period.

Low-energy particle experiments-ion mass analyzer (LEPi) onboard the ERG (Arase) satellite

NASA Astrophysics Data System (ADS)

Asamura, K.; Kazama, Y.; Yokota, S.; Kasahara, S.; Miyoshi, Y.

2018-05-01

Low-energy ion experiments-ion mass analyzer (LEPi) is one of the particle instruments onboard the ERG satellite. LEPi is an ion energy-mass spectrometer which covers the range of particle energies from < 0.01 to 25 keV/q. Species of incoming ions are discriminated by a combination of electrostatic energy-per-charge analysis and the time-of-flight technique. The sensor has a planar field-of-view, which provides 4π steradian coverage by using the spin motion of the satellite. LEPi started its nominal observation after the initial checkout and commissioning phase in space. [Figure not available: see fulltext.

ZTF Undergraduate Astronomy Institute at Caltech and Pomona College

NASA Astrophysics Data System (ADS)

Penprase, Bryan Edward; Bellm, Eric Christopher

2017-01-01

From the new Zwicky Transient Facility (ZTF), an NSF funded project based at Caltech, comes a new initiative for undergraduate research known as the Summer Undergraduate Astronomy Institute. The Institute brings together 15-20 students from across the world for an immersive experience in astronomy techniques before they begin their summer research projects. The students are primarly based at Caltech in their SURF program but also includes a large cohort of students enrolled in research internships at Pomona College in nearby Claremont CA. The program is intended to introduce students to research techniques in astronomy, laboratory and computational technologies, and to observational astronomy. Since many of the students are previously computer science or physics majors with little astronomy experience, this immersive experience has been extremely helpful for enabling students to learn about the terminologies, techniques and technologies of astronomy. The field trips to the Mount Wilson and Palomar telescopes deepen their knowledge and excitement about astronomy. Lectures about astronomical research from Caltech staff scientists and graduate students also provide context for the student research. Perhaps more importantly, the creation of a cohort of like-minded students, and the chance to reflect about careers in astronomy and research, give these students opportunities to consider themselves as future research scientists and help them immensely as they move forward in their careers. We discuss some of the social and intercultural aspects of the experience as well, as our cohorts typically include international students from many countries and several students from under-represented groups in science.

Analysis of dewar and transfer line cooldown in Superfluid Helium On-Orbit Transfer Flight Experiment (SHOOT)

NASA Technical Reports Server (NTRS)

Ng, Y. S.; Lee, J. H.

1989-01-01

The Superfluid Helium On-Orbit Transfer Flight Experiment (SHOOT) is designed to demonstrate the techniques and components required for orbital superfluid (He II) replenishment of observatories and satellites. One of the tasks planned in the experiment is to cool a warm cryogen tank and a warm transfer line to liquid helium temperature. A math model, based on single-phase vapor flow heat transfer, has been developed to predict the cooldown time, component temperature histories, and helium consumption rate, for various initial conditions of the components and for the thermomechanical pump heater powers of 2 W and 0.5 W. This paper discusses the model and the analytical results, which can be used for planning the experiment operations and determining the pump heater power required for the cooldown operation.

Ground deformation monitoring using small baseline DInSAR technique: A case study in Taiyuan City from 2003 to 2009

USGS Publications Warehouse

Wu, H.-A.; Zhang, Y.-H.; Chen, X.-Y.; Lu, T.; Du, J.; Sun, Z.-H.; Sun, G.-T.

2011-01-01

DInSAR technique based on time series of SAR images has been very popular to monitor ground stow deformation in recent years such as permanent scatterers (PS) method small baseline subsets (SBAS) method and coherent targets (CT) method. By taking advantage of PS method and CT method in this paper small baseline DTnSAR technique is used to investigate the ground deformation of Taiyuan City Shanxi Province from 2003 to 2009 by using 23 ENVISAT ASAR images. The experiment results demonstrate that: (1) during this period four significant subsidence centers have been developed in Taiyuan namely Xiayuan Wujiabu Xiaodian Sunjiazhai. The largest subsidence center is Sunjiazhai with an average subsidence rate of -77. 28 mm/a; (2) The subsidence of the old center Wanbolin has sHowed down. And the subsidence in the northern region has stopped and some areas even rebounded. (3) The change of subsidence centers indicates that the control measures of "closing wells and reducing exploitation" taken by the Taiyuan government has achieved initial effects. (4) The experiment results have been validated with leveling data and the acouracy is 2. 90 mm which shows that the small baseline DInSAR technique can be used to monitor urban ground deformation.

Using scenarios to capture work processes in shared home care.

PubMed

Hägglund, Maria; Scandurra, Isabella; Koch, Sabine

2007-01-01

Shared home care is increasingly common, and in order to develop ICT that support such complex cooperative work it is crucial obtain an understanding of the work routines, information demands, and other central preconditions at the clinical level before the development is initiated. Scenarios are proposed as a technique that can be useful for capturing work processes in shared home care and experiences from the Old@Home project are presented. The scenarios are useful not only in the initial phases of the development project but throughout the development process, improving the accessibility of end user requirements and usability issues for the design team, and as a basis for use cases and further design.

Design Mining Interacting Wind Turbines.

PubMed

Preen, Richard J; Bull, Larry

2016-01-01

An initial study has recently been presented of surrogate-assisted evolutionary algorithms used to design vertical-axis wind turbines wherein candidate prototypes are evaluated under fan-generated wind conditions after being physically instantiated by a 3D printer. Unlike other approaches, such as computational fluid dynamics simulations, no mathematical formulations were used and no model assumptions were made. This paper extends that work by exploring alternative surrogate modelling and evolutionary techniques. The accuracy of various modelling algorithms used to estimate the fitness of evaluated individuals from the initial experiments is compared. The effect of temporally windowing surrogate model training samples is explored. A surrogate-assisted approach based on an enhanced local search is introduced; and alternative coevolution collaboration schemes are examined.

First measurement of proton's charge form factor at very low Q 2 with initial state radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mihovilovič, M.; Weber, A. B.; Achenbach, P.

Here we report on a new experimental method based on initial-state radiation (ISR) in e–pscattering, which exploits the radiative tail of the elastic peak to study the properties of electromagnetic processes and to extract the proton charge form factor (Gmore » $$p\\atop{E}$$) at extremely small Q 2. The ISR technique was implemented in an experiment at the three-spectrometer facility of the Mainz Microtron (MAMI). This led to a precise validation of radiative corrections far away from elastic line and provided first measurements of G$$p\\atop{E}$$ for 0.001 ≤Q 2≤0.004 (GeV/c) 2.« less

First measurement of proton's charge form factor at very low Q 2 with initial state radiation

DOE PAGES

Mihovilovič, M.; Weber, A. B.; Achenbach, P.; ...

2017-05-15

Here we report on a new experimental method based on initial-state radiation (ISR) in e–pscattering, which exploits the radiative tail of the elastic peak to study the properties of electromagnetic processes and to extract the proton charge form factor (Gmore » $$p\\atop{E}$$) at extremely small Q 2. The ISR technique was implemented in an experiment at the three-spectrometer facility of the Mainz Microtron (MAMI). This led to a precise validation of radiative corrections far away from elastic line and provided first measurements of G$$p\\atop{E}$$ for 0.001 ≤Q 2≤0.004 (GeV/c) 2.« less

A new Method for the Estimation of Initial Condition Uncertainty Structures in Mesoscale Models

NASA Astrophysics Data System (ADS)

Keller, J. D.; Bach, L.; Hense, A.

2012-12-01

The estimation of fast growing error modes of a system is a key interest of ensemble data assimilation when assessing uncertainty in initial conditions. Over the last two decades three methods (and variations of these methods) have evolved for global numerical weather prediction models: ensemble Kalman filter, singular vectors and breeding of growing modes (or now ensemble transform). While the former incorporates a priori model error information and observation error estimates to determine ensemble initial conditions, the latter two techniques directly address the error structures associated with Lyapunov vectors. However, in global models these structures are mainly associated with transient global wave patterns. When assessing initial condition uncertainty in mesoscale limited area models, several problems regarding the aforementioned techniques arise: (a) additional sources of uncertainty on the smaller scales contribute to the error and (b) error structures from the global scale may quickly move through the model domain (depending on the size of the domain). To address the latter problem, perturbation structures from global models are often included in the mesoscale predictions as perturbed boundary conditions. However, the initial perturbations (when used) are often generated with a variant of an ensemble Kalman filter which does not necessarily focus on the large scale error patterns. In the framework of the European regional reanalysis project of the Hans-Ertel-Center for Weather Research we use a mesoscale model with an implemented nudging data assimilation scheme which does not support ensemble data assimilation at all. In preparation of an ensemble-based regional reanalysis and for the estimation of three-dimensional atmospheric covariance structures, we implemented a new method for the assessment of fast growing error modes for mesoscale limited area models. The so-called self-breeding is development based on the breeding of growing modes technique. Initial perturbations are integrated forward for a short time period and then rescaled and added to the initial state again. Iterating this rapid breeding cycle provides estimates for the initial uncertainty structure (or local Lyapunov vectors) given a specific norm. To avoid that all ensemble perturbations converge towards the leading local Lyapunov vector we apply an ensemble transform variant to orthogonalize the perturbations in the sub-space spanned by the ensemble. By choosing different kind of norms to measure perturbation growth, this technique allows for estimating uncertainty patterns targeted at specific sources of errors (e.g. convection, turbulence). With case study experiments we show applications of the self-breeding method for different sources of uncertainty and different horizontal scales.

Cold plasma processing of local planetary ores for oxygen and metallurgically important metals

NASA Technical Reports Server (NTRS)

Lynch, D. C.; Bullard, D.; Ortega, R.

1991-01-01

The utilization of a cold or nonequilibrium plasma in chlorination processing is discussed. Titanium dioxide (TiO2) was successfully chlorinated at temperatures between 700 and 900 C without the aid of carbon. In addition to these initial experiments, a technique was developed for determining the temperature of a specimen in a plasma. Development of that technique has required evaluating the emissivity of TiO2, ZrO2, and FeOTiO2 and analyzing the specimen temperature in a plasma as a function of both power absorbed by the plasma and the pressure of the plasma. The mass spectrometer was also calibrated with TiCl4 and CCl4 vapor.

ROENTGEN: case-based reasoning and radiation therapy planning.

PubMed Central

Berger, J.

1992-01-01

ROENTGEN is a design assistant for radiation therapy planning which uses case-based reasoning, an artificial intelligence technique. It learns both from specific problem-solving experiences and from direct instruction from the user. The first sort of learning is the normal case-based method of storing problem solutions so that they can be reused. The second sort is necessary because ROENTGEN does not, initially, have an internal model of the physics of its problem domain. This dependence on explicit user instruction brings to the forefront representational questions regarding indexing, failure definition, failure explanation and repair. This paper presents the techniques used by ROENTGEN in its knowledge acquisition and design activities. PMID:1482869

Novel strategies for sample preparation in forensic toxicology.

PubMed

Samanidou, Victoria; Kovatsi, Leda; Fragou, Domniki; Rentifis, Konstantinos

2011-09-01

This paper provides a review of novel strategies for sample preparation in forensic toxicology. The review initially outlines the principle of each technique, followed by sections addressing each class of abused drugs separately. The novel strategies currently reviewed focus on the preparation of various biological samples for the subsequent determination of opiates, benzodiazepines, amphetamines, cocaine, hallucinogens, tricyclic antidepressants, antipsychotics and cannabinoids. According to our experience, these analytes are the most frequently responsible for intoxications in Greece. The applications of techniques such as disposable pipette extraction, microextraction by packed sorbent, matrix solid-phase dispersion, solid-phase microextraction, polymer monolith microextraction, stir bar sorptive extraction and others, which are rapidly gaining acceptance in the field of toxicology, are currently reviewed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nasser, Felipe; Rocha, Rafael Dahmer, E-mail: rafaeldrocha@gmail.com; Falsarella, Priscila Mina

PurposeTo report a novel modified occlusion balloon technique to treat biliary leaks.MethodsA 22-year-old female patient underwent liver transplantation with biliary-enteric anastomosis. She developed thrombosis of the common hepatic artery and extensive ischemia in the left hepatic lobe. Resection of segments II and III was performed and a biliary-cutaneous leak originating at the resection plane was identified in the early postoperative period. Initial treatment with percutaneous transhepatic drainage was unsuccessful. Therefore, an angioplasty balloon was coaxially inserted within the biliary drain and positioned close to the leak.ResultsThe fistula output abruptly decreased after the procedure and stopped on the 7th day. Atmore » the 3-week follow-up, cholangiography revealed complete resolution of the leakage.ConclusionThis novel modified occlusion balloon technique was effective and safe. However, greater experience and more cases are necessary to validate the technique.« less

Scheduling Earth Observing Satellites with Evolutionary Algorithms

NASA Technical Reports Server (NTRS)

Globus, Al; Crawford, James; Lohn, Jason; Pryor, Anna

2003-01-01

We hypothesize that evolutionary algorithms can effectively schedule coordinated fleets of Earth observing satellites. The constraints are complex and the bottlenecks are not well understood, a condition where evolutionary algorithms are often effective. This is, in part, because evolutionary algorithms require only that one can represent solutions, modify solutions, and evaluate solution fitness. To test the hypothesis we have developed a representative set of problems, produced optimization software (in Java) to solve them, and run experiments comparing techniques. This paper presents initial results of a comparison of several evolutionary and other optimization techniques; namely the genetic algorithm, simulated annealing, squeaky wheel optimization, and stochastic hill climbing. We also compare separate satellite vs. integrated scheduling of a two satellite constellation. While the results are not definitive, tests to date suggest that simulated annealing is the best search technique and integrated scheduling is superior.

Applying shot boundary detection for automated crystal growth analysis during in situ transmission electron microscope experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moeglein, W. A.; Griswold, R.; Mehdi, B. L.

In-situ (scanning) transmission electron microscopy (S/TEM) is being developed for numerous applications in the study of nucleation and growth under electrochemical driving forces. For this type of experiment, one of the key parameters is to identify when nucleation initiates. Typically the process of identifying the moment that crystals begin to form is a manual process requiring the user to perform an observation and respond accordingly (adjust focus, magnification, translate the stage etc.). However, as the speed of the cameras being used to perform these observations increases, the ability of a user to “catch” the important initial stage of nucleation decreasesmore » (there is more information that is available in the first few milliseconds of the process). Here we show that video shot boundary detection (SBD) can automatically detect frames where a change in the image occurs. We show that this method can be applied to quickly and accurately identify points of change during crystal growth. This technique allows for automated segmentation of a digital stream for further analysis and the assignment of arbitrary time stamps for the initiation of processes that are independent of the user’s ability to observe and react.« less

Initial experience of Da Vinci robotic thoracic surgery at the First Affiliated Hospital of Zhejiang University

PubMed Central

He, Zhehao; Zeng, Liping; Zhang, Chong; Wang, Luming; Wang, Zhitian; Rustam, Azmat; Du, Chengli; Lv, Wang

2017-01-01

Robot-assisted thoracic surgery (RATS) is a relatively new but rapidly adopted technique, pioneered by the urological and gynecological departments. The primary objective of this study is to present the current status, a series of improvement and innovation of Da Vinci robotic surgery in the Department of Thoracic Surgery at First Affiliated Hospital of Zhejiang University. In addition, we discuss the prospect of robotic surgical technology. PMID:29302429

What defines an Expert? - Uncertainty in the interpretation of seismic data

NASA Astrophysics Data System (ADS)

Bond, C. E.

2008-12-01

Studies focusing on the elicitation of information from experts are concentrated primarily in economics and world markets, medical practice and expert witness testimonies. Expert elicitation theory has been applied in the natural sciences, most notably in the prediction of fluid flow in hydrological studies. In the geological sciences expert elicitation has been limited to theoretical analysis with studies focusing on the elicitation element, gaining expert opinion rather than necessarily understanding the basis behind the expert view. In these cases experts are defined in a traditional sense, based for example on: standing in the field, no. of years of experience, no. of peer reviewed publications, the experts position in a company hierarchy or academia. Here traditional indicators of expertise have been compared for significance on affective seismic interpretation. Polytomous regression analysis has been used to assess the relative significance of length and type of experience on the outcome of a seismic interpretation exercise. Following the initial analysis the techniques used by participants to interpret the seismic image were added as additional variables to the analysis. Specific technical skills and techniques were found to be more important for the affective geological interpretation of seismic data than the traditional indicators of expertise. The results of a seismic interpretation exercise, the techniques used to interpret the seismic and the participant's prior experience have been combined and analysed to answer the question - who is and what defines an expert?

Double-Diffusive Finger Convection: Flow Field Evolution in a Hele-Shaw Cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

COOPER,CLAY A.; GLASS JR.,ROBERT J.; TYLER,SCOTT W.

Double-diffusive finger convection is a hydrodynamic instability that can occur when two components with different diffusivities are oppositely stratified with respect to the fluid density gradient as a critical condition is exceeded. Laboratory experiments were designed using sodium chloride and sucrose solutions in a Hele-Shaw cell. A high resolution, full field, light transmission technique was used to study the development of the instability. The initial buoyancy ratio (R{sub p}), which is a ratio of fluid density contributions by the two solutes, was varied systematically in the experiments so that the range of parameter space spanned conditions that were nearly stablemore » (R{sub p} = 2.8) to those that were moderately unstable (R{sub p} = 1.4). In systems of low R{sub p}, fingers develop within several minutes, merge with adjacent fingers, form conduits, and stall before newer-generated fingers travel through the conduits and continue the process. Solute fluxes in low R{sub p} systems quickly reach steady state and are on the order of 10{sup {minus}6} m{sup 2} sec{sup {minus}1}. In the higher R{sub p} experiments, fingers are slower to evolve and do not interact as dynamically as in the lower R{sub p} systems. Our experiment with initial R{sub p} = 2.8 exhibited flux on the order of that expected for a similar diffusive system (i.e., 10{sup {minus}7} m{sup 2} sec{sup {minus}1}), although the structures were very different than the pattern of transport expected in a diffusing system. Mass flux decayed as t{sup 1/2} in two experiments each with initial R{sub p} = 2.4 and 2.8.« less

Data Assimilation - Advances and Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Brian J.

2014-07-30

This presentation provides an overview of data assimilation (model calibration) for complex computer experiments. Calibration refers to the process of probabilistically constraining uncertain physics/engineering model inputs to be consistent with observed experimental data. An initial probability distribution for these parameters is updated using the experimental information. Utilization of surrogate models and empirical adjustment for model form error in code calibration form the basis for the statistical methodology considered. The role of probabilistic code calibration in supporting code validation is discussed. Incorporation of model form uncertainty in rigorous uncertainty quantification (UQ) analyses is also addressed. Design criteria used within a batchmore » sequential design algorithm are introduced for efficiently achieving predictive maturity and improved code calibration. Predictive maturity refers to obtaining stable predictive inference with calibrated computer codes. These approaches allow for augmentation of initial experiment designs for collecting new physical data. A standard framework for data assimilation is presented and techniques for updating the posterior distribution of the state variables based on particle filtering and the ensemble Kalman filter are introduced.« less

Internal Gravity Waves: Generation and Breaking Mechanisms by Laboratory Experiments

NASA Astrophysics Data System (ADS)

la Forgia, Giovanni; Adduce, Claudia; Falcini, Federico

2016-04-01

Internal gravity waves (IGWs), occurring within estuaries and the coastal oceans, are manifest as large amplitude undulations of the pycnocline. IGWs propagating horizontally in a two layer stratified fluid are studied. The breaking of an IGW of depression shoaling upon a uniformly sloping boundary is investigated experimentally. Breaking dynamics beneath the shoaling waves causes both mixing and wave-induced near-bottom vortices suspending and redistributing the bed material. Laboratory experiments are conducted in a Perspex tank through the standard lock-release method, following the technique described in Sutherland et al. (2013). Each experiment is analysed and the instantaneous pycnocline position is measured, in order to obtain both geometric and kinematic features of the IGW: amplitude, wavelength and celerity. IGWs main features depend on the geometrical parameters that define the initial experimental setting: the density difference between the layers, the total depth, the layers depth ratio, the aspect ratio, and the displacement between the pycnoclines. Relations between IGWs geometric and kinematic features and the initial setting parameters are analysed. The approach of the IGWs toward a uniform slope is investigated in the present experiments. Depending on wave and slope characteristics, different breaking and mixing processes are observed. Sediments are sprinkled on the slope to visualize boundary layer separation in order to analyze the suspension e redistribution mechanisms due to the wave breaking.

Minimum information about a biofilm experiment (MIABiE): standards for reporting experiments and data on sessile microbial communities living at interfaces.

PubMed

Lourenço, Anália; Coenye, Tom; Goeres, Darla M; Donelli, Gianfranco; Azevedo, Andreia S; Ceri, Howard; Coelho, Filipa L; Flemming, Hans-Curt; Juhna, Talis; Lopes, Susana P; Oliveira, Rosário; Oliver, Antonio; Shirtliff, Mark E; Sousa, Ana M; Stoodley, Paul; Pereira, Maria Olivia; Azevedo, Nuno F

2014-04-01

The minimum information about a biofilm experiment (MIABiE) initiative has arisen from the need to find an adequate and scientifically sound way to control the quality of the documentation accompanying the public deposition of biofilm-related data, particularly those obtained using high-throughput devices and techniques. Thereby, the MIABiE consortium has initiated the identification and organization of a set of modules containing the minimum information that needs to be reported to guarantee the interpretability and independent verification of experimental results and their integration with knowledge coming from other fields. MIABiE does not intend to propose specific standards on how biofilms experiments should be performed, because it is acknowledged that specific research questions require specific conditions which may deviate from any standardization. Instead, MIABiE presents guidelines about the data to be recorded and published in order for the procedure and results to be easily and unequivocally interpreted and reproduced. Overall, MIABiE opens up the discussion about a number of particular areas of interest and attempts to achieve a broad consensus about which biofilm data and metadata should be reported in scientific journals in a systematic, rigorous and understandable manner. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Radio detection of cosmic-ray air showers and high-energy neutrinos

NASA Astrophysics Data System (ADS)

Schröder, Frank G.

2017-03-01

In the last fifteen years radio detection made it back to the list of promising techniques for extensive air showers, firstly, due to the installation and successful operation of digital radio experiments and, secondly, due to the quantitative understanding of the radio emission from atmospheric particle cascades. The radio technique has an energy threshold of about 100 PeV, which coincides with the energy at which a transition from the highest-energy galactic sources to the even more energetic extragalactic cosmic rays is assumed. Thus, radio detectors are particularly useful to study the highest-energy galactic particles and ultra-high-energy extragalactic particles of all types. Recent measurements by various antenna arrays like LOPES, CODALEMA, AERA, LOFAR, Tunka-Rex, and others have shown that radio measurements can compete in precision with other established techniques, in particular for the arrival direction, the energy, and the position of the shower maximum, which is one of the best estimators for the composition of the primary cosmic rays. The scientific potential of the radio technique seems to be maximum in combination with particle detectors, because this combination of complementary detectors can significantly increase the total accuracy for air-shower measurements. This increase in accuracy is crucial for a better separation of different primary particles, like gamma-ray photons, neutrinos, or different types of nuclei, because showers initiated by these particles differ in average depth of the shower maximum and in the ratio between the amplitude of the radio signal and the number of muons. In addition to air-shower measurements, the radio technique can be used to measure particle cascades in dense media, which is a promising technique for detection of ultra-high-energy neutrinos. Several pioneering experiments like ARA, ARIANNA, and ANITA are currently searching for the radio emission by neutrino-induced particle cascades in ice. In the next years these two sub-fields of radio detection of cascades in air and in dense media will likely merge, because several future projects aim at the simultaneous detection of both, high-energy cosmic-rays and neutrinos. SKA will search for neutrino and cosmic-ray initiated cascades in the lunar regolith and simultaneously provide unprecedented detail for air-shower measurements. Moreover, detectors with huge exposure like GRAND, SWORD or EVA are being considered to study the highest energy cosmic rays and neutrinos. This review provides an introduction to the physics of radio emission by particle cascades, an overview on the various experiments and their instrumental properties, and a summary of methods for reconstructing the most important air-shower properties from radio measurements. Finally, potential applications of the radio technique in high-energy astroparticle physics are discussed.

Surface electrical properties experiment. [for Taurus-Littrow region of the moon on Apollo 17

NASA Technical Reports Server (NTRS)

Simmons, G.

1974-01-01

The Surface Electrical Properties Experiment (SEP) was flown to the moon in December 1972 on Apollo 17 and used to explore a portion of the Taurus-Littrow region. SEP used a relatively new technique, termed radio frequency interferometry (RFI). Electromagnetic waves were radiated from two orthogonal, horizontal electric dipole antennas on the surface of the moon at frequencies of 1, 2, 4, 8, 16, and 32 Mhz. The field strength of the EM waves was measured as a function of distance with a receiver mounted on the Lunar Roving Vehicle and using three orthogonal, electrically small, loops. The interference pattern produced by the waves that travelled above the moon's surface and those that travelled below the surface was recorded on magnetic tape. The tape was returned to earth for analysis and interpretation. Several reprints, preprints, and an initial draft of the first publication of the SEP results are included. These documents provide a rather complete account of the details of the theory of the RFI technique, of the terrestrial tests of the technique, and of the present state of our interpretation of the Apollo 17 data.

Visualizing deceleration-phase instabilities in inertial confinement fusion implosions using an "enhanced self-emission" technique at the National Ignition Facility

NASA Astrophysics Data System (ADS)

Pickworth, L. A.; Hammel, B. A.; Smalyuk, V. A.; Robey, H. F.; Benedetti, L. R.; Berzak Hopkins, L.; Bradley, D. K.; Field, J. E.; Haan, S. W.; Hatarik, R.; Hartouni, E.; Izumi, N.; Johnson, S.; Khan, S.; Lahmann, B.; Landen, O. L.; Le Pape, S.; MacPhee, A. G.; Meezan, N. B.; Milovich, J.; Nagel, S. R.; Nikroo, A.; Pak, A. E.; Petrasso, R.; Remington, B. A.; Rice, N. G.; Springer, P. T.; Stadermann, M.; Widmann, K.; Hsing, W.

2018-05-01

High-mode perturbations and low-mode asymmetries were measured in the deceleration phase of indirectly driven, deuterium gas filled inertial confinement fusion capsule implosions at convergence ratios of 10 to 15, using a new "enhanced emission" technique at the National Ignition Facility [E. M. Campbell et al., AIP Conf. Proc. 429, 3 (1998)]. In these experiments, a high spatial resolution Kirkpatrick-Baez microscope was used to image the x-ray emission from the inner surface of a high-density-carbon capsule's shell. The use of a high atomic number dopant in the shell enabled time-resolved observations of shell perturbations penetrating into the hot spot. This allowed the effects of the perturbations and asymmetries on degrading neutron yield to be directly measured. In particular, mix induced radiation losses of ˜400 J from the hot spot resulted in a neutron yield reduction of a factor of ˜2. In a subsequent experiment with a significantly increased level of short-mode initial perturbations, shown through the enhanced imaging technique to be highly organized radially, the neutron yield dropped an additional factor of ˜2.

A tractable prescription for large-scale free flight expansion of wavefunctions

NASA Astrophysics Data System (ADS)

Deuar, P.

2016-11-01

A numerical recipe is given for obtaining the density image of an initially compact quantum mechanical wavefunction that has expanded by a large but finite factor under free flight. The recipe given avoids the memory storage problems that plague this type of calculation by reducing the problem to the sum of a number of fast Fourier transforms carried out on the relatively small initial lattice. The final expanded state is given exactly on a coarser magnified grid with the same number of points as the initial state. An important application of this technique is the simulation of measured time-of-flight images in ultracold atom experiments, especially when the initial clouds contain superfluid defects. It is shown that such a finite-time expansion, rather than a far-field approximation is essential to correctly predict images of defect-laden clouds, even for long flight times. Examples shown are: an expanding quasicondensate with soliton defects and a matter-wave interferometer in 3D.

Laparoendoscopic single-site extraperitoneal inguinal hernia repair: initial experience in 10 patients.

PubMed

Do, Minh; Liatsikos, Evangelos; Beatty, John; Haefner, Tim; Dunn, Ian; Kallidonis, Panagiotis; Stolzenburg, Jens-Uwe

2011-06-01

Recent technical advances and a trend toward laparoscopic single incision surgery have led us to explore the feasibility of laparoendoscopic single-site (LESS) hernia repair. We present our technique and initial experience with LESS extraperitoneal inguinal hernia repair in 10 consecutive men with unilateral inguinal hernias. Age range was 43.7 (28-64) years. Mean body mass index was 28 (range 24-30). Six were left inguinal hernias. There were six indirect and four direct hernias. Three patients had undergone previous open appendectomy. Incarcerated or bilateral hernias were excluded from our initial series. All cases were performed by three surgeons who were experienced in conventional totally extraperitoneal laparoscopic hernia repair as well as experienced in LESS. A literature review of current single-port inguinal hernia repair data is also presented. The mean operative time was 53 minutes (range 45-65  min). The average length of skin incision was 2.8  cm (range 2.3-3.2  cm). No drain was necessary in any of the patients, while no recordable bleeding was observed. There were no intraoperative or immediate postoperative complications. Hospitalization period was 2 days for all patients. After a limited follow-up of 1 month, there have been no recurrences and no complaints of testicular pain. The results of the current series compare favorably with those found in a literature review. LESS extraperitoneal inguinal hernia repair is both feasible and safe, although more technically demanding than its conventional laparoscopic counterpart. Although the cosmetic result with the former approach may prove superior, there are standing questions regarding the complications and long-term outcome. Randomized and if possible blinded trials that compare conventional and single-incision laparoscopic hernia repair may help to distinguish the most advantageous technique.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasdekis, Andreas E.; Stephanopoulos, Gregory

The sampling and manipulation of cells down to the individual has been of substantial interest since the very beginning of Life Sciences. Herein, our objective is to highlight the most recent developments in single cell manipulation, as well as pioneering ones. First, flow-through methods will be discussed, namely methods in which the single cells flow continuously in an ordered manner during their analysis. This section will be followed by confinement techniques that enable cell isolation and confinement in one, two- or three-dimensions. Flow cytometry and droplet microfluidics are the two most common methods of flow-through analysis. While both are high-throughputmore » techniques, their difference lays in the fact that the droplet encapsulated cells experience a restricted and personal microenvironment, while in flow cytometry cells experience similar nutrient and stimuli initial concentrations. These methods are rather well established; however, they recently enabled immense strides in single cell phenotypic analysis, namely the identification and analysis of metabolically distinct individuals from an isogenic population using both droplet microfluidics and flow cytometry.« less

Towards a Compositional SPIN

NASA Technical Reports Server (NTRS)

Pasareanu, Corina S.; Giannakopoulou, Dimitra

2006-01-01

This paper discusses our initial experience with introducing automated assume-guarantee verification based on learning in the SPIN tool. We believe that compositional verification techniques such as assume-guarantee reasoning could complement the state-reduction techniques that SPIN already supports, thus increasing the size of systems that SPIN can handle. We present a "light-weight" approach to evaluating the benefits of learning-based assume-guarantee reasoning in the context of SPIN: we turn our previous implementation of learning for the LTSA tool into a main program that externally invokes SPIN to provide the model checking-related answers. Despite its performance overheads (which mandate a future implementation within SPIN itself), this approach provides accurate information about the savings in memory. We have experimented with several versions of learning-based assume guarantee reasoning, including a novel heuristic introduced here for generating component assumptions when their environment is unavailable. We illustrate the benefits of learning-based assume-guarantee reasoning in SPIN through the example of a resource arbiter for a spacecraft. Keywords: assume-guarantee reasoning, model checking, learning.

Reaction Rates Of Olivine Carbonation - An Experimental Study Using Synthetic Fluid Inclusions As Micro-Reactors

NASA Astrophysics Data System (ADS)

Sendula, E.; Lamadrid, H. M.; Bodnar, R. J.

2017-12-01

Ultramafic and mafic rocks (e.g. peridotites, serpentinites and basalts) are being considered as possible targets for CO2 sequestration via mineral carbonation. The determination of reaction kinetics and the factors that control mineralization are important in order to understand and predict fluid-rock reactions between the injected CO2 and the host rocks. Here we present results of experiments focused on determining the reaction rates of carbonation of olivine as a function of initial CO2 concentration (20 mol% and 11 mol%) in the aqueous solution and temperature (100°C and 50°C). We used a recently developed experimental method (Lamadrid et al., 2017) that uses synthetic fluid inclusions as micro-reactors. The micro-reactor technique coupled with non-destructive Raman spectroscopy allows us to monitor the reaction progress in situ and in real time, by quantifying the amount of CO2 consumed in the reaction as a function of time. Results show a measurable decrease of CO2 density in the fluid inclusions as a result of the reaction between the CO2-bearing aqueous phase and olivine. Magnesite formation begins within several hours at 100°C and most of the CO2 was consumed within two days. At 50°C, however, magnesite nucleation and precipitation required weeks to months to begin, and the reaction rates were about an order of magnitude slower than in the experiments at 100°C. No significant differences were observed in the reaction rates as a function of initial CO2 concentration. The application of the synthetic fluid inclusion technique as micro-reactors coupled with non-destructive analytical techniques is a promising tool to monitor rates of fluid-rock reactions in situ and in real time, allowing detailed micron-scale investigations. The technique can be applied to a wide variety of chemical systems, host minerals, reaction products, fluid densities, temperatures, and different starting fluid compositions.

Early experience of transaortic TAVI--the future of surgical TAVI?

PubMed

Clarke, Andrew; Wiemers, Paul; Poon, Karl K C; Aroney, Constantine N; Scalia, Gregory; Burstow, Darryl; Walters, Darren L; Tesar, Peter

2013-04-01

Trans-catheter aortic valve implantation (TAVI) is now a well recognised procedure for the high risk surgical patient with native or bioprosthetic aortic valve stenosis. Transfemoral and transapical implantation techniques are well described. With increasing referral of more marginal transapical patients, we describe our experience of a transaortic TAVI approach which we believe reduces the postoperative wound pain, respiratory complications, operative risk and hospital stay. Patients referred for surgical TAVI underwent trans-catheter aortic valve implantation via an upper sternotomy and direct cannulation of the ascending aorta. Thirteen patients with a mean age of 81 years underwent transaortic Edwards SAPIEN valve implantation. There was no in hospital mortality in our series. One patient required insertion of a permanent pacemaker for complete heart block. There were no aortic cannulation complications. The transaortic TAVI approach provides good exposure of the distal ascending aorta, a familiar cannulation site for cardiac surgeons. Our initial experience demonstrates the approach to be a safe technique with the potential for faster and less complicated recovery in patients undergoing surgical TAVI procedures. With further experience and greater acceptance, the transaortic approach may ultimately become the procedure of choice for patients unsuitable for a transfemoral approach. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

Protein crystal growth in a microgravity environment

NASA Technical Reports Server (NTRS)

Bugg, Charles E.

1988-01-01

Protein crystal growth is a major experimental problem and is the bottleneck in widespread applications of protein crystallography. Research efforts now being pursued and sponsored by NASA are making fundamental contributions to the understanding of the science of protein crystal growth. Microgravity environments offer the possibility of performing new types of experiments that may produce a better understanding of protein crystal growth processes and may permit growth environments that are more favorable for obtaining high quality protein crystals. A series of protein crystal growth experiments using the space shuttle was initiated. The first phase of these experiments was focused on the development of micro-methods for protein crystal growth by vapor diffusion techniques, using a space version of the hanging drop method. The preliminary space experiments were used to evolve prototype hardware that will form the basis for a more advanced system that can be used to evaluate effects of gravity on protein crystal growth.

What Can We Learn from Hugoniot Temperature as a Function of Shock Velocity?

NASA Astrophysics Data System (ADS)

LI, M.; Jeanloz, R.

2015-12-01

Shock-wave experiments traditionally rely on impact techniques, whereby measured shock velocity (US) can be related to material velocity (up), determined from the impact velocity (= 2up for a symmetric impact), and resulting in the empirically observed linear US-up equation of state: US = c0 + s up. Modern experiments relying on laser-driven compression have the advantage of reaching higher pressures than laboratory impact experiments, but up is typically not determined; instead, Hugoniot temperature (TH) and shock velocity are more readily measured. Assuming a linear US-up equation of state and that the Grüneisen parameter has the volume dependence g(V) = g0 (V/V0), measurements of the Hugoniot temperature as a function of shock velocity provide constraints on the specific heat along the Hugoniot CVH(US) = V0 f(US)[c0 g0 TH - s US dTH/dUS]-1 where the Walsh-Christian (1955) function f(US) = - (US - c0)2 US/(V0 s c0) = TH dSH/dVH gives the entropy change along the Hugoniot (subscripts 0 and H indicate zero-pressure and Hugoniot states, respectively). In this sense, TH(US) measurements are similar to calorimetry experiments. If specific heat and Grüneisen parameter are determined independently (e.g., from wave-velocity measurements and experiments on porous samples), the TH(US) analog to the linear US-up equation of state is TH(US) = {T0 exp(g0 /s) - ò[V0 c0 f(x)/(s x CV)] exp[c0 g0 /(s x)] dx} exp[- c0 g0 /(s US)] where the integration is from x = c0 to x = US. In addition, experiments can be considered with: 1) different initial volume, as in a porous sample; 2) different initial internal energy, as in a sample heated at constant volume; and 3) different initial volume and internal energy, as in a sample initially heated at ambient pressure. From these four initial states, we get four different Hugoniot curves, and can also consider the effect of phase transition latent heat. Temperature as a function of shock velocity may thus be benefit the analysis of melting and other phase transitions with small volume change and finite latent heat.

Conformational plasticity of RepB, the replication initiator protein of promiscuous streptococcal plasmid pMV158

PubMed Central

Boer, D. Roeland; Ruiz-Masó, José Angel; Rueda, Manuel; Petoukhov, Maxim V.; Machón, Cristina; Svergun, Dmitri I.; Orozco, Modesto; del Solar, Gloria; Coll, Miquel

2016-01-01

DNA replication initiation is a vital and tightly regulated step in all replicons and requires an initiator factor that specifically recognizes the DNA replication origin and starts replication. RepB from the promiscuous streptococcal plasmid pMV158 is a hexameric ring protein evolutionary related to viral initiators. Here we explore the conformational plasticity of the RepB hexamer by i) SAXS, ii) sedimentation experiments, iii) molecular simulations and iv) X-ray crystallography. Combining these techniques, we derive an estimate of the conformational ensemble in solution showing that the C-terminal oligomerisation domains of the protein form a rigid cylindrical scaffold to which the N-terminal DNA-binding/catalytic domains are attached as highly flexible appendages, featuring multiple orientations. In addition, we show that the hinge region connecting both domains plays a pivotal role in the observed plasticity. Sequence comparisons and a literature survey show that this hinge region could exists in other initiators, suggesting that it is a common, crucial structural element for DNA binding and manipulation. PMID:26875695

Mode I Failure of Armor Ceramics: Experiments and Modeling

NASA Astrophysics Data System (ADS)

Meredith, Christopher; Leavy, Brian

2017-06-01

The pre-notched edge on impact (EOI) experiment is a technique for benchmarking the damage and fracture of ceramics subjected to projectile impact. A cylindrical projectile impacts the edge of a thin rectangular plate with a pre-notch on the opposite edge. Tension is generated at the notch tip resulting in the initiation and propagation of a mode I crack back toward the impact edge. The crack can be quantitatively measured using an optical method called Digital Gradient Sensing, which measures the crack-tip deformation by simultaneously quantifying two orthogonal surface slopes via measuring small deflections of light rays from a specularly reflective surface around the crack. The deflections in ceramics are small so the high speed camera needs to have a very high pixel count. This work reports on the results from pre-crack EOI experiments of SiC and B4 C plates. The experimental data are quantitatively compared to impact simulations using an advanced continuum damage model. The Kayenta ceramic model in Alegra will be used to compare fracture propagation speeds, bifurcations and inhomogeneous initiation of failure will be compared. This will provide insight into the driving mechanisms required for the macroscale failure modeling of ceramics.

Skipping Strategy (SS) for Initial Population of Job-Shop Scheduling Problem

NASA Astrophysics Data System (ADS)

Abdolrazzagh-Nezhad, M.; Nababan, E. B.; Sarim, H. M.

2018-03-01

Initial population in job-shop scheduling problem (JSSP) is an essential step to obtain near optimal solution. Techniques used to solve JSSP are computationally demanding. Skipping strategy (SS) is employed to acquire initial population after sequence of job on machine and sequence of operations (expressed in Plates-jobs and mPlates-jobs) are determined. The proposed technique is applied to benchmark datasets and the results are compared to that of other initialization techniques. It is shown that the initial population obtained from the SS approach could generate optimal solution.

Lidar In-space Technology Experiment: Overview and early results

NASA Technical Reports Server (NTRS)

McCormick, M. Patrick

1995-01-01

The September 1994 Shuttle flight of the Lidar In-space Technology Experiment (LITE) brought to fruition 10 years of effort at NASA's Langley Research Center where it was built. Being the first flight of a spaceborne lidar to measure atmospheric constituents and parameters and surface properties, it culminates the efforts of many worldwide over the last 20 years to usher in this new remote sensing technique from space. This paper will describe the LITE instrument, the in-orbit performance, and initial results. In addition, the global correlative measurements program will be outlined which involved 60 groups in 20 countries who made various simultaneous ground-based or aircraft measurements as LITE flew overhead.

The lambda point experiment in microgravity

NASA Technical Reports Server (NTRS)

Lipa, J. A.

1988-01-01

The motivation and potential for performing very high resolution measurements of the heat capacity singularity at the lambda point of helium in microgravity conditions was briefly discussed. It is clear that tests extending deep into the asymptotic region can be performed, where the theoretical predictions take on their simplest form. This advantageous situation should lead to a major improvement in the understanding of the range of applicability of current theoretical ideas in this field. The lambda transition holds out the prospect of giving the maximum advance of any system, and with the application of cryogenic techniques, the potential of this system can be realized. The technology for the initial experiments is already developed, and results could be obtained in 1990.

Format and basic geometry of a perspective display of air traffic for the cockpit

NASA Technical Reports Server (NTRS)

Mcgreevy, Michael Wallace; Ellis, Stephen R.

1991-01-01

The design and implementation of a perspective display of air traffic for the cockpit is discussed. Parameters of the perspective are variable and interactive so that the appearance of the projected image can be widely varied. This approach makes allowances for exploration of perspective parameters and their interactions. The display was initially used to study the cases of horizontal maneuver biases found in experiments involving a plan view air traffic display format. Experiments to determine the effect of perspective geometry on spatial judgements have evolved from the display program. Several scaling techniques and other adjustments to the perspective are used to tailor the geometry for effective presentation of 3-D traffic situations.

Evaluating uncertainties in multi-layer soil moisture estimation with support vector machines and ensemble Kalman filtering

NASA Astrophysics Data System (ADS)

Liu, Di; Mishra, Ashok K.; Yu, Zhongbo

2016-07-01

This paper examines the combination of support vector machines (SVM) and the dual ensemble Kalman filter (EnKF) technique to estimate root zone soil moisture at different soil layers up to 100 cm depth. Multiple experiments are conducted in a data rich environment to construct and validate the SVM model and to explore the effectiveness and robustness of the EnKF technique. It was observed that the performance of SVM relies more on the initial length of training set than other factors (e.g., cost function, regularization parameter, and kernel parameters). The dual EnKF technique proved to be efficient to improve SVM with observed data either at each time step or at a flexible time steps. The EnKF technique can reach its maximum efficiency when the updating ensemble size approaches a certain threshold. It was observed that the SVM model performance for the multi-layer soil moisture estimation can be influenced by the rainfall magnitude (e.g., dry and wet spells).

Initial experience with a new articulating energy device for laparoscopic liver resection.

PubMed

Berber, Eren; Akyuz, Muhammet; Aucejo, Federico; Aliyev, Shamil; Aksoy, Erol; Birsen, Onur; Taskin, Eren

2014-03-01

Although significant advances have been made in laparoscopic liver resection (LLR), most techniques still rely on multiple energy devices and staplers, which increase operative costs. The aim of this study was to report the initial results of a new multifunctional energy device for hepatic parenchymal transection. Fourteen patients who underwent LLR using this new device were compared to 20 patients who had LLR using current laparoscopic techniques (CL). Data were collected prospectively. The groups were similar demographics and tumor type and size. Although the type of resection was similar between the groups, the parenchymal transection time was less in the Caiman group (32 ± 5 vs. 63 ± 4 min, respectively, p = 0.0001). The operative time was similar (194 ± 21 vs. 233 ± 16 min, respectively, p = 0.158). There was reduction of the number of advanced instrumentation used in the Caiman group, including the staplers. Estimated blood loss, size of surgical margin, and hospital stay were similar. There was no mortality, and morbidity was 7 % in the Caiman and 20 % in the CL group. This initial study shows that the new device is safe and efficient for LLR. Its main advantage is shortening of hepatic parenchymal transection time. This has implications for increasing efficiency and cost saving in LLR.

Mission Operations Planning with Preferences: An Empirical Study

NASA Technical Reports Server (NTRS)

Bresina, John L.; Khatib, Lina; McGann, Conor

2006-01-01

This paper presents an empirical study of some nonexhaustive approaches to optimizing preferences within the context of constraint-based, mixed-initiative planning for mission operations. This work is motivated by the experience of deploying and operating the MAPGEN (Mixed-initiative Activity Plan GENerator) system for the Mars Exploration Rover Mission. Responsiveness to the user is one of the important requirements for MAPGEN, hence, the additional computation time needed to optimize preferences must be kept within reasonabble bounds. This was the primary motivation for studying non-exhaustive optimization approaches. The specific goals of rhe empirical study are to assess the impact on solution quality of two greedy heuristics used in MAPGEN and to assess the improvement gained by applying a linear programming optimization technique to the final solution.

Translating the Simulation of Procedural Drilling Techniques for Interactive Neurosurgical Training

PubMed Central

Stredney, Don; Rezai, Ali R.; Prevedello, Daniel M.; Elder, J. Bradley; Kerwin, Thomas; Hittle, Bradley; Wiet, Gregory J.

2014-01-01

Background Through previous and concurrent efforts, we have developed a fully virtual environment to provide procedural training of otologic surgical technique. The virtual environment is based on high-resolution volumetric data of the regional anatomy. This volumetric data helps drive an interactive multi-sensory, i.e., visual (stereo), aural (stereo), and tactile simulation environment. Subsequently, we have extended our efforts to support the training of neurosurgical procedural technique as part of the CNS simulation initiative. Objective The goal of this multi-level development is to deliberately study the integration of simulation technologies into the neurosurgical curriculum and to determine their efficacy in teaching minimally invasive cranial and skull base approaches. Methods We discuss issues of biofidelity as well as our methods to provide objective, quantitative automated assessment for the residents. Results We conclude with a discussion of our experiences by reporting on preliminary formative pilot studies and proposed approaches to take the simulation to the next level through additional validation studies. Conclusion We have presented our efforts to translate an otologic simulation environment for use in the neurosurgical curriculum. We have demonstrated the initial proof of principles and define the steps to integrate and validate the system as an adjuvant to the neurosurgical curriculum. PMID:24051887

Comparison of three-dimensional particle tracking and sizing using plenoptic imaging and digital in-line holography.

PubMed

Hall, Elise M; Thurow, Brian S; Guildenbecher, Daniel R

2016-08-10

Digital in-line holography (DIH) and plenoptic photography are two techniques for single-shot, volumetric measurement of 3D particle fields. Here we present a comparison of the two methods by applying plenoptic imaging to experimental configurations that have been previously investigated with DIH. These experiments include the tracking of secondary droplets from the impact of a water drop on a thin film of water and tracking of pellets from a shotgun. Both plenoptic imaging and DIH successfully quantify the 3D nature of these particle fields. This includes measurement of the 3D particle position, individual particle sizes, and three-component velocity vectors. For the initial processing methods presented here, both techniques give out-of-plane positional accuracy of approximately 1-2 particle diameters. For a fixed image sensor, digital holography achieves higher effective in-plane spatial resolutions. However, collimated and coherent illumination makes holography susceptible to image distortion through index of refraction gradients, as demonstrated in the shotgun experiments. In contrast, plenoptic imaging allows for a simpler experimental configuration and, due to the use of diffuse, white-light illumination, plenoptic imaging is less susceptible to image distortion in the shotgun experiments.

From synapses to behavior: development of a sensory-motor circuit in the leech.

PubMed

Marin-Burgin, Antonia; Kristan, William B; French, Kathleen A

2008-05-01

The development of neuronal circuits has been advanced greatly by the use of imaging techniques that reveal the activity of neurons during the period when they are constructing synapses and forming circuits. This review focuses on experiments performed in leech embryos to characterize the development of a neuronal circuit that produces a simple segmental behavior called "local bending." The experiments combined electrophysiology, anatomy, and FRET-based voltage-sensitive dyes (VSDs). The VSDs offered two major advantages in these experiments: they allowed us to record simultaneously the activity of many neurons, and unlike other imaging techniques, they revealed inhibition as well as excitation. The results indicated that connections within the circuit are formed in a predictable sequence: initially neurons in the circuit are connected by electrical synapses, forming a network that itself generates an embryonic behavior and prefigures the adult circuit; later chemical synapses, including inhibitory connections, appear, "sculpting" the circuit to generate a different, mature behavior. In this developmental process, some of the electrical connections are completely replaced by chemical synapses, others are maintained into adulthood, and still others persist and share their targets with chemical synaptic connections.

A survey of particle contamination in electronic devices

NASA Technical Reports Server (NTRS)

Adolphsen, J. W.; Kagdis, W. A.; Timmins, A. R.

1976-01-01

The experiences are given of a number of National Aeronautics and Space Administration (NASA) and Space and Missile System Organization (SAMSO) contractors with particle contamination, and the methods used for its prevention and detection, evaluates the bases for the different schemes, assesses their effectiveness, and identifies the problems associated with each. It recommends specific short-range tests or approaches appropriate to individual part-type categories and recommends that specific tasks be initiated to refine techniques and to resolve technical and application facets of promising solutions.

Deposition of tantalum carbide coatings on graphite by laser interactions

NASA Technical Reports Server (NTRS)

Veligdan, James; Branch, D.; Vanier, P. E.; Barietta, R. E.

1994-01-01

Graphite surfaces can be hardened and protected from erosion by hydrogen at high temperatures by refractory metal carbide coatings, which are usually prepared by chemical vapor deposition (CVD) or chemical vapor reaction (CVR) methods. These techniques rely on heating the substrate to a temperature where a volatile metal halide decomposes and reacts with either a hydrocarbon gas or with carbon from the substrate. For CVR techniques, deposition temperatures must be in excess of 2000 C in order to achieve favorable deposition kinetics. In an effort to lower the bulk substrate deposition temperature, the use of laser interactions with both the substrate and the metal halide deposition gas has been employed. Initial testing involved the use of a CO2 laser to heat the surface of a graphite substrate and a KrF excimer laser to accomplish a photodecomposition of TaCl5 gas near the substrate. The results of preliminary experiments using these techniques are described.

Successful emergency pain control for posterior rib fractures with ultrasound-guided erector spinae plane block.

PubMed

Luftig, Josh; Mantuani, Daniel; Herring, Andrew A; Dixon, Brittany; Clattenburg, Eben; Nagdev, Arun

2017-12-28

The Eastern Association for the Surgery of Trauma and Trauma Anesthesiology Society Guidelines recommend prompt and effective multimodal analgesia for rib fractures that combines regional anesthesia (RA) techniques with pharmacotherapy to treat pain, optimize pulmonary function, and reduce opioid related complications. However, RA techniques such as epidurals and paravertebral blocks, are generally underutilized or unavailable for emergency department (ED) patients. The recently described serratus anterior plane block (SAPB) is a promising technique, but failures with posterior rib fractures have been observed. The erector spinae plane block (ESPB) is conceptually similar to the SAPB, but targets the posterior thorax making it likely more effective for ED patients with posterior rib fractures. Our initial experience demonstrates consistent success with the ESPB for traumatic posterior rib fracture analgesia. Herein, we present the first description of the ESPB utilized in the ED. Copyright © 2017 Elsevier Inc. All rights reserved.

Accidental Turbulent Discharge Rate Estimation from Videos

NASA Astrophysics Data System (ADS)

Ibarra, Eric; Shaffer, Franklin; Savaş, Ömer

2015-11-01

A technique to estimate the volumetric discharge rate in accidental oil releases using high speed video streams is described. The essence of the method is similar to PIV processing, however the cross correlation is carried out on the visible features of the efflux, which are usually turbulent, opaque and immiscible. The key step in the process is to perform a pixelwise time filtering on the video stream, in which the parameters are commensurate with the scales of the large eddies. The velocity field extracted from the shell of visible features is then used to construct an approximate velocity profile within the discharge. The technique has been tested on laboratory experiments using both water and oil jets at Re ~105 . The technique is accurate to 20%, which is sufficient for initial responders to deploy adequate resources for containment. The software package requires minimal user input and is intended for deployment on an ROV in the field. Supported by DOI via NETL.

Effects of environmental conditions on the ultrafast carrier dynamics in graphene revealed by terahertz spectroscopy

NASA Astrophysics Data System (ADS)

Hafez, H. A.; Chai, X.; Sekine, Y.; Takamura, M.; Oguri, K.; Al-Naib, I.; Dignam, M. M.; Hibino, H.; Ozaki, T.

2017-04-01

A thorough understanding of the stability of graphene under ambient environmental conditions is essential for future graphene-based applications. In this paper, we study the effects of ambient temperature on the properties of monolayer graphene using terahertz time-domain spectroscopy as well as time-resolved terahertz spectroscopy enabled by an optical-pump/terahertz-probe technique. The observations show that graphene is extremely sensitive to the ambient environmental conditions and behaves differently depending on the sample preparation technique and the initial Fermi level. The analysis of the spectroscopic data is supported by van der Pauw and Hall effect measurements of the carrier mobility and carrier density at temperatures comparable to those tested in our THz spectroscopic experiments.

Spectra, composition and interactions of nuclei above 10 TeV using magnet-interferometric chambers (SCIN/MAGIC)

NASA Technical Reports Server (NTRS)

Wefel, John P.

1991-01-01

Initial definition studies were performed for the SCIN/MAGIC experiment selected as an Astromag investigation on Space Station Freedom. The study focused on Science Objectives and Science Requirement, Accommodation on both the STS and the Astromag facility, Data extraction techniques and Background Studies. The detectors are emulsion chambers which will be exposed for approximately 90 days and then recovered from orbit for subsequent processing and analysis in the laboratory. Such a technique is the only means to obtain information on the ultrahigh energy cosmic rays and their nuclear interactions. The SCIN/MAGIC investigation can supply unique data in relatively unexplored energy region and address many of the fundamental questions in particle astrophysics.

Fabricating fiber Bragg gratings with two phase masks based on reconstruction-equivalent-chirp technique.

PubMed

Gao, Liang; Chen, Xiangfei; Xiong, Jintian; Liu, Shengchun; Pu, Tao

2012-01-30

Based on reconstruction-equivalent-chirp (REC) technique, a novel solution for fabricating low-cost long fiber Bragg gratings (FBGs) with desired properties is proposed and initially studied. A proof-of-concept experiment is demonstrated with two conventional uniform phase masks and a submicron-precision translation stage, successfully. It is shown that the original phase shift (OPS) caused by phase mismatch of the two phase masks can be compensated by the equivalent phase shift (EPS) at the ±1st channels of sampled FBGs, separately. Furthermore, as an example, a π phase-shifted FBG of about 90 mm is fabricated by using these two 50mm-long uniform phase masks based on the presented method.

Note: An approach to 1000 T using the electro-magnetic flux compression.

PubMed

Nakamura, D; Sawabe, H; Takeyama, S

2018-01-01

The maximum magnetic field obtained by the electro-magnetic flux compression technique was investigated with respect to the initial seed magnetic field. It was found that the reduction in the seed magnetic field from 3.8 T to 3.0 T led to a substantial increase in the final peak magnetic field. The optical Faraday rotation method with a minimal size probe evades disturbances from electromagnetic noise and shockwave effects to detect such final peak fields in a reduced space of an inner wall of the imploding liner. The Faraday rotation signal recorded the maximum magnetic field increased significantly to the highest magnetic field of 985 T approaching 1000 T, ever achieved by the electro-magnetic flux compression technique as an indoor experiment.

Trends and Techniques for Space Base Electronics

NASA Technical Reports Server (NTRS)

Trotter, J. D.; Wade, T. E.; Gassaway, J. D.

1979-01-01

Simulations of various phosphorus and boron diffusions in SOS were completed and a sputtering system, furnaces, and photolithography related equipment were set up. Double layer metal experiments initially utilized wet chemistry techniques. By incorporating ultrasonic etching of the vias, premetal cleaning a modified buffered HF, phosphorus doped vapox, and extended sintering, yields of 98% were obtained using the standard test pattern. A two dimensional modeling program was written for simulating short channel MOSFETs with nonuniform substrate doping. A key simplifying assumption used is that the majority carriers can be represented by a sheet charge at the silicon dioxide silicon interface. Although the program is incomplete, the two dimensional Poisson equation for the potential distribution was achieved. The status of other Z-D MOSFET simulation programs is summarized.

Spread spectrum mobile communication experiment using ETS-V satellite

NASA Technical Reports Server (NTRS)

Ikegami, Tetsushi; Suzuki, Ryutaro; Kadowaki, Naoto; Taira, Shinichi; Sato, Nobuyasu

1990-01-01

The spread spectrum technique is attractive for application to mobile satellite communications, because of its random access capability, immunity to inter-system interference, and robustness to overloading. A novel direct sequence spread spectrum communication equipment is developed for land mobile satellite applications. The equipment is developed based on a matched filter technique to improve the initial acquisition performance. The data rate is 2.4 kilobits per sec. and the PN clock rate is 2.4552 mega-Hz. This equipment also has a function of measuring the multipath delay profile of land mobile satellite channel, making use of a correlation property of a PN code. This paper gives an outline of the equipment and the field test results with ETS-V satellite.

Nano-Electrochemistry and Nano-Electrografting with an Original Combined AFM-SECM

PubMed Central

Ghorbal, Achraf; Grisotto, Federico; Charlier, Julienne; Palacin, Serge; Goyer, Cédric; Demaille, Christophe; Ben Brahim, Ammar

2013-01-01

This study demonstrates the advantages of the combination between atomic force microscopy and scanning electrochemical microscopy. The combined technique can perform nano-electrochemical measurements onto agarose surface and nano-electrografting of non-conducting polymers onto conducting surfaces. This work was achieved by manufacturing an original Atomic Force Microscopy-Scanning ElectroChemical Microscopy (AFM-SECM) electrode. The capabilities of the AFM-SECM-electrode were tested with the nano-electrografting of vinylic monomers initiated by aryl diazonium salts. Nano-electrochemical and technical processes were thoroughly described, so as to allow experiments reproducing. A plausible explanation of chemical and electrochemical mechanisms, leading to the nano-grafting process, was reported. This combined technique represents the first step towards improved nano-processes for the nano-electrografting. PMID:28348337

The Optimal Surgical Approach for Treatment of Chronic Subdural Hematoma: Questionnaire Assessment of Practice in Iran and Review of Literature.

PubMed

Javadi, Seyed Amir Hossein; Naderi, Fereshteh; Javadi, Amir Mohammad

2015-10-01

Chronic subdural hematoma (CSDH) is a curable entity frequently encountered by neurosurgeons. The present study was conducted to explore expert opinion and common practice in Iran. Besides, a Review of randomized clinical trials in literature was performed. A questionnaire including six questions discussing major aspects of practice on CSDH, with multiple choices was designed. A pilot study was performed for reliability analysis of the questionnaire. A total of 100 neurosurgeons were selected randomly from the members of Iranian Association of Neurological Surgeons. Frequency of answers to each item, differences in response rates and correlation of various categories were analyzed using Chi-square statistics. The mean duration of experience was 15.4 ± 5 years, with a range of 10 to 37 years. The most common initial procedure of choice was burr-hole drainage (64%). At recurrent cases, surgical approach was changed to craniotomy at one-third of those treated initially with burr-hole drainage. The participants believed that surgical technique was predictive of outcome and recurrence. Burr-hole without drainage was used by less expert neurosurgeons (mean 12.5 ± 6), however, burr-hole drainage was the dominant technique at more than 15 years of experience and craniectomy was used only by participants with more than 30 years of experience (10%). Irrigation was used by most of the neurosurgeons (87.5%) in combination with drainage and burr-hole. The majority of participants used flat position at the postoperative period. At the current study, the pattern of management for CSDH was similar to other reports at literature suggesting the burr-hole drainage and irrigation as optimal treatment. Individualized decision-making could be made at challenging cases.

Assimilation of satellite altimeter data into an open ocean model

NASA Astrophysics Data System (ADS)

Vogeler, Armin; SchröTer, Jens

1995-08-01

Geosat sea surface height data are assimilated into an eddy-resolving quasi-geostrophic open ocean model using the adjoint technique. The method adjusts the initial conditions for all layers and is successful on the timescale of a few weeks. Time-varying values for the open boundaries are prescribed by a much larger quasi-geostrophic model of the Antarctic Circumpolar Current (ACC). Both models have the same resolution of approximately 20×20 km (1/3°×1/6°), have three layers, and include realistic bottom topography and coastlines. The open model box is embedded in the African sector of the ACC. For continuous assimilation of satellite data into the larger model the nudging technique is applied. These results are used for the adjoint optimization procedure as boundary conditions and as a first guess for the initial condition. For the open model box the difference between model and satellite sea surface height that remains after the nudging experiment amounts to a 19-cm root-mean-square error (rmse). By assimilation into the regional model this value can be reduced to a 6-cm rmse for an assimilation period of 20 days. Several experiments which attempt to improve the convergence of the iterative optimization method are reported. Scaling and regularization by smoothing have to be applied carefully. Especially during the first 10 iterations, the convergence can be improved considerably by low-pass filtering of the cost function gradient. The result of a perturbation experiment shows that for longer assimilation periods the influence of the boundary values becomes dominant and they should be determined inversely by data assimilation into the open ocean model.

Onyx embolization using dual-lumen balloon catheter: initial experience and technical note.

PubMed

Paramasivam, Srinivasan; Niimi, Yasunari; Fifi, Johanna; Berenstein, Alejandro

2013-10-01

Onyx as an embolization agent for the management of vascular malformation is well established. We report our initial experience with dimethyl-sulphoxide (DMSO) compatible double lumen balloon catheters used for Onyx embolization. Between December 2011 and March 2013, we treated 22 patients aged between 1.5 to 70years with two types of DMSO compatible dual-lumen balloon catheters (Scepter C and Ascent) to treat dural arteriovenous fistulas, brain arteriovenous malformation (AVM) with dural feeders, mandibular, facial, lingual, vertebral and paravertebral AVMs. The catheter has good navigability, compliant balloon on inflation formed a "plug" that has more resistance than Onyx plug enhancing better penetration. During injection, the balloon remained stable without spontaneous deflation or rupture and withstood the pressure build-up well. The retrieval of the catheter in most cases took less than a minute (19/28) while in five, it was less than five minutes and in the remaining four, it was longer that includes a trapped catheter on prolonged attempted retrieval resulted in an epidural hematoma, requiring emergent surgical evacuation. The fluoroscopy time is reduced, as we do not form a proximal onyx plug, the injection time is shorter along with easy and instantaneous removal of the catheter after balloon deflation in most cases. Dual-lumen balloon catheter Onyx embolization is a safe and effective technique. Currently, an important tool to circumvent some of the shortcomings associated with Onyx embolization. The catheter has good navigability, the balloon has stability, tolerance, enhances penetrability. It is easy to retrieve the microcatheter. With the experience gained, and with more compliant balloon catheters available, this technique can be applied to cerebral vessels in near future. Copyright © 2013. Published by Elsevier Masson SAS.

Robotic surgery of locally advanced gastric cancer: a single-surgeon experience of 41 cases.

PubMed

Vasilescu, C; Procopiuc, L

2012-01-01

The mainstay of curative gastric cancer treatment is open gastric resection with regional lymph node dissection. Minimally invasive surgery is yet to become an established technique with a well defined role. Robotic surgery has by-passed some of the limitations of conventional laparoscopy and has proven both safe and feasible. We present our initial experience with robotic surgery based on 41 gastric cancer patients. We especially wish to underline the advantages of the robotic system when performing the digestive tract anastomoses. We present the techniques of end-to-side eso-jejunoanastomoses (using a circular stapler or manual suture) and side-to-side eso-jejunoanastomoses. In our hands, the results with circular stapled anastomoses were good and we advocate against manual suturing when performing anastomoses in robotic surgery. Moreover, we recommend performing totally intracorporeal anastomoses which have a better post-operative outcome, especially in obese patients. We present three methods of realising the total intracorporeal eso-jejuno-anastomosis with a circular stapler: manual purse-string suture, using the OrVil and the double stapling technique. The eso-jejunoanastomosis is one of the most difficult steps in performing the total gastrectomy, but these techniques allow the surgeon to choose the best option for each case. We consider that surgeons who undertake total gastrectomies must have a special training in performing these anastomoses.

Shock-Ramp Loading of Tin and Aluminum

NASA Astrophysics Data System (ADS)

Seagle, Christopher; Davis, Jean; Martin, Matthew; Hanshaw, Heath

2013-06-01

Equation of state properties for materials off the principle Hugoniot and isentrope are currently poorly constrained. The ability to directly probe regions of phase space between the Hugoniot and isentrope under dynamic loading will greatly improve our ability to constrain equation of state properties under a variety of conditions and study otherwise inaccessible phase transitions. We have developed a technique at Sandia's Z accelerator to send a steady shock wave through a material under test, and subsequently ramp compress from the Hugoniot state. The shock-ramp experimental platform results in a unique loading path and enables probing of equation of state properties in regions of phase space otherwise difficult to access in dynamic experiments. A two-point minimization technique has been developed for the analysis of shock-ramp velocity data. The technique correctly accounts for the ``initial'' Hugoniot density of the material under test before the ramp wave arrives. Elevated quasi-isentropes have been measured for solid aluminum up to 1.4 Mbar and liquid tin up to 1.1 Mbar using the shock ramp technique. These experiments and the analysis of the resulting velocity profiles will be discussed. Sandia National Laboratories is a multi-program laboratory operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85.

Engineering calculations for communications satellite systems planning

NASA Technical Reports Server (NTRS)

Reilly, C. H.; Levis, C. A.; Mount-Campbell, C.; Gonsalvez, D. J.; Wang, C. W.; Yamamura, Y.

1985-01-01

Computer-based techniques for optimizing communications-satellite orbit and frequency assignments are discussed. A gradient-search code was tested against a BSS scenario derived from the RARC-83 data. Improvement was obtained, but each iteration requires about 50 minutes of IBM-3081 CPU time. Gradient-search experiments on a small FSS test problem, consisting of a single service area served by 8 satellites, showed quickest convergence when the satellites were all initially placed near the center of the available orbital arc with moderate spacing. A transformation technique is proposed for investigating the surface topography of the objective function used in the gradient-search method. A new synthesis approach is based on transforming single-entry interference constraints into corresponding constraints on satellite spacings. These constraints are used with linear objective functions to formulate the co-channel orbital assignment task as a linear-programming (LP) problem or mixed integer programming (MIP) problem. Globally optimal solutions are always found with the MIP problems, but not necessarily with the LP problems. The MIP solutions can be used to evaluate the quality of the LP solutions. The initial results are very encouraging.

Detection of early changes in lung-cell cytology by flow-systems analysis techniques. Progress report, January 1--June 30, 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinkamp, J. A.; Hansen, K. M.; Wilson, J. S.

1976-08-01

This report summarizes results of preliminary experiments to develop cytological and biochemical indicators for estimating damage to respiratory epithelium exposed to toxic agents associated with the by-products of nonnuclear energy production using advanced flow-systems cell-analysis technologies. Since initiation of the program one year ago, progress has been made in obtaining adequate numbers of exfoliated lung cells from the Syrian hamster for flow analysis; cytological techniques developed on human exfoliated gynecological samples have been adapted to hamster lung epithelium for obtaining single-cell suspensions; and lung-cell samples have been initially characterized based on DNA content, total protein, nuclear and cytoplasmic size, andmore » multiangle light-scatter measurements. Preliminary results from measurements of the above parameters which recently became available are described in this report. As the flow-systems technology is adapted further to analysis of exfoliated lung cells, measurements of changes in physical and biochemical cellular properties as a function of exposure to toxic agents will be performed.« less

Evaluation of Bogus Vortex Techniques with Four-Dimensional Variational Data Assimilation

NASA Technical Reports Server (NTRS)

Pu, Zhao-Xia; Braun, Scott A.

2000-01-01

The effectiveness of techniques for creating "bogus" vortices in numerical simulations of hurricanes is examined by using the Penn State/NCAR nonhydrostatic mesoscale model (MM5) and its adjoint system. A series of four-dimensional variational data assimilation (4-D VAR) experiments is conducted to generate an initial vortex for Hurricane Georges (1998) in the Atlantic Ocean by assimilating bogus sea-level pressure and surface wind information into the mesoscale numerical model. Several different strategies are tested for improving the vortex representation. The initial vortices produced by the 4-D VAR technique are able to reproduce many of the structural features of mature hurricanes. The vortices also result in significant improvements to the hurricane forecasts in terms of both intensity and track. In particular, with assimilation of only bogus sea-level pressure information, the response in the wind field is contained largely within the divergent component, with strong convergence leading to strong upward motion near the center. Although the intensity of the initial vortex seems to be well represented, a dramatic spin down of the storm occurs within the first 6 h of the forecast. With assimilation of bogus surface wind data only, an expected dominance of the rotational component of the wind field is generated, but the minimum pressure is adjusted inadequately compared to the actual hurricane minimum pressure. Only when both the bogus surface pressure and wind information are assimilated together does the model produce a vortex that represents the actual intensity of the hurricane and results in significant improvements to forecasts of both hurricane intensity and track.

Semantic Repositories for eGovernment Initiatives: Integrating Knowledge and Services

NASA Astrophysics Data System (ADS)

Palmonari, Matteo; Viscusi, Gianluigi

In recent years, public sector investments in eGovernment initiatives have depended on making more reliable existing governmental ICT systems and infrastructures. Furthermore, we assist at a change in the focus of public sector management, from the disaggregation, competition and performance measurements typical of the New Public Management (NPM), to new models of governance, aiming for the reintegration of services under a new perspective in bureaucracy, namely a holistic approach to policy making which exploits the extensive digitalization of administrative operations. In this scenario, major challenges are related to support effective access to information both at the front-end level, by means of highly modular and customizable content provision, and at the back-end level, by means of information integration initiatives. Repositories of information about data and services that exploit semantic models and technologies can support these goals by bridging the gap between the data-level representations and the human-level knowledge involved in accessing information and in searching for services. Moreover, semantic repository technologies can reach a new level of automation for different tasks involved in interoperability programs, both related to data integration techniques and service-oriented computing approaches. In this chapter, we discuss the above topics by referring to techniques and experiences where repositories based on conceptual models and ontologies are used at different levels in eGovernment initiatives: at the back-end level to produce a comprehensive view of the information managed in the public administrations' (PA) information systems, and at the front-end level to support effective service delivery.

Minimizing complications of ultrasound-assisted lipoplasty: an initial experience with no related complications.

PubMed

Tebbetts, J B

1998-10-01

Numerous complications and increased operating times were reported with ultrasonically assisted lipoplasty in the first several months after introduction of the technology in the United States. The purpose of this study was to review early reported complications and management regimens, evaluate possible causes of problems, and apply indications and techniques to attempt to minimize complications during an initial experience with this technique beginning in January of 1997. Seven specific indications and modifications of existing techniques were developed and applied to an initial clinical series of 70 consecutive patients who underwent ultrasound-assisted suction lipoplasty between January 10, 1997, and August 1, 1997. Follow-up ranged from 1 to 7 months. No perioperative or postoperative complication occurred in any patient in this series. In this series of ultrasound-assisted lipoplasty cases, application of the following criteria resulted in a series of 70 patients with 1 to 7-month follow-up without complications: (1) selecting patients with well localized fat deposits who were no more than 20 percent above their ideal body weight; (2) infusing a solution of Ringer's Lactate containing 1 cc of 1:1000 epinephrine per 1000 cc into the area of fat removal, stopping infusion when the tissues first become firm, not infusing to marked tissue turgor or skin induration; (3) restricting the level of energy application to a minimum of 1 cm from the undersurface of the dermis; (4) limiting ultrasonic energy application in each area to approximately 1 minute per estimated 100 cc of total aspirate in a wet to superwet environment; (5) not performing ultrasound-assisted lipoplasty in the same area as another procedure that could potentially compromise tissue vascularity; (6) using a Lysonix 2000 generator and 5-mm golf tee tip probe at a power setting of 8 to apply ultrasonic energy to the area of fat removal, ceasing energy application when tissue resistance to the passage of the probe decreases and moving the cannula as rapidly as tissue resistance allows; and (7) using a standard elastic garment without adherent foam or other materials for 2 weeks postoperatively, encouraging all normal activity immediately, and restricting aerobic activities for 2 weeks.

Collecting and Analyzing Patient Experiences of Health Care From Social Media.

PubMed

Rastegar-Mojarad, Majid; Ye, Zhan; Wall, Daniel; Murali, Narayana; Lin, Simon

2015-07-02

Social Media, such as Yelp, provides rich information of consumer experience. Previous studies suggest that Yelp can serve as a new source to study patient experience. However, the lack of a corpus of patient reviews causes a major bottleneck for applying computational techniques. The objective of this study is to create a corpus of patient experience (COPE) and report descriptive statistics to characterize COPE. Yelp reviews about health care-related businesses were extracted from the Yelp Academic Dataset. Natural language processing (NLP) tools were used to split reviews into sentences, extract noun phrases and adjectives from each sentence, and generate parse trees and dependency trees for each sentence. Sentiment analysis techniques and Hadoop were used to calculate a sentiment score of each sentence and for parallel processing, respectively. COPE contains 79,173 sentences from 6914 patient reviews of 985 health care facilities near 30 universities in the United States. We found that patients wrote longer reviews when they rated the facility poorly (1 or 2 stars). We demonstrated that the computed sentiment scores correlated well with consumer-generated ratings. A consumer vocabulary to describe their health care experience was constructed by a statistical analysis of word counts and co-occurrences in COPE. A corpus called COPE was built as an initial step to utilize social media to understand patient experiences at health care facilities. The corpus is available to download and COPE can be used in future studies to extract knowledge of patients' experiences from their perspectives. Such information can subsequently inform and provide opportunity to improve the quality of health care.

Posttest examination of Sodium Loop Safety Facility experiments. [LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, J.W.

In-reactor, safety experiments performed in the Sodium Loop Safety Facility (SLSF) rely on comprehensive posttest examinations (PTE) to characterize the postirradiation condition of the cladding, fuel, and other test-subassembly components. PTE information and on-line instrumentation data, are analyzed to identify the sequence of events and the severity of the accident for each experiment. Following in-reactor experimentation, the SLSF loop and test assembly are transported to the Hot Fuel Examination Facility (HFEF) for initial disassembly. Goals of the HFEF-phase of the PTE are to retrieve the fuel bundle by dismantling the loop and withdrawing the test assembly, to assess the macro-conditionmore » of the fuel bundle by nondestructive examination techniques, and to prepare the fuel bundle for shipment to the Alpha-Gamma Hot Cell Facility (AGHCF) at Argonne National Laboratory.« less

Recent experience in seeding transonic/supersonic flows at AEDC

NASA Astrophysics Data System (ADS)

Heltsley, F. L.

1985-10-01

The laser velocimeter has been utilized for several years at the Arnold Engineering and Development Center (AEDC) as a flow diagnostics tool. Most applications, following the initial proof-of-concept experiments, have involved relatively complex unknown flow fields in which the more conventional, intrusive techniques had either not been attempted or had yielded unsatisfactory results. A blunt-base nozzle-afterbody base flow study is discussed as a respresentative example of such applications. A wide variety of problems have been encountered during these tests, many of which have proven to be closely related to the size and/or size distribution of the seeding material within the fluid. Resulting measurement uncertainties could often not be conclusively resolved because of the unknown nature of the flow field. The other experiments listed were conducted to provide known aerodynamic conditions for comparison with the velocimeter results.

Recent experience in seeding transonic/supersonic flows at AEDC

NASA Technical Reports Server (NTRS)

Heltsley, F. L.

1985-01-01

The laser velocimeter has been utilized for several years at the Arnold Engineering and Development Center (AEDC) as a flow diagnostics tool. Most applications, following the initial proof-of-concept experiments, have involved relatively complex unknown flow fields in which the more conventional, intrusive techniques had either not been attempted or had yielded unsatisfactory results. A blunt-base nozzle-afterbody base flow study is discussed as a respresentative example of such applications. A wide variety of problems have been encountered during these tests, many of which have proven to be closely related to the size and/or size distribution of the seeding material within the fluid. Resulting measurement uncertainties could often not be conclusively resolved because of the unknown nature of the flow field. The other experiments listed were conducted to provide known aerodynamic conditions for comparison with the velocimeter results.

In silico modelling of drug–polymer interactions for pharmaceutical formulations

PubMed Central

Ahmad, Samina; Johnston, Blair F.; Mackay, Simon P.; Schatzlein, Andreas G.; Gellert, Paul; Sengupta, Durba; Uchegbu, Ijeoma F.

2010-01-01

Selecting polymers for drug encapsulation in pharmaceutical formulations is usually made after extensive trial and error experiments. To speed up excipient choice procedures, we have explored coarse-grained computer simulations (dissipative particle dynamics (DPD) and coarse-grained molecular dynamics using the MARTINI force field) of polymer–drug interactions to study the encapsulation of prednisolone (log p = 1.6), paracetamol (log p = 0.3) and isoniazid (log p = −1.1) in poly(l-lactic acid) (PLA) controlled release microspheres, as well as the encapsulation of propofol (log p = 4.1) in bioavailability enhancing quaternary ammonium palmitoyl glycol chitosan (GCPQ) micelles. Simulations have been compared with experimental data. DPD simulations, in good correlation with experimental data, correctly revealed that hydrophobic drugs (prednisolone and paracetamol) could be encapsulated within PLA microspheres and predicted the experimentally observed paracetamol encapsulation levels (5–8% of the initial drug level) in 50 mg ml−1 PLA microspheres, but only when initial paracetamol levels exceeded 5 mg ml−1. However, the mesoscale technique was unable to model the hydrophilic drug (isoniazid) encapsulation (4–9% of the initial drug level) which was observed in experiments. Molecular dynamics simulations using the MARTINI force field indicated that the self-assembly of GCPQ is rapid, with propofol residing at the interface between micellar hydrophobic and hydrophilic groups, and that there is a heterogeneous distribution of propofol within the GCPQ micelle population. GCPQ–propofol experiments also revealed a population of relatively empty and drug-filled GCPQ particles. PMID:20519214

Optimization of photocatalytic degradation of methyl blue using silver ion doped titanium dioxide by combination of experimental design and response surface approach.

PubMed

Sahoo, C; Gupta, A K

2012-05-15

Photocatalytic degradation of methyl blue (MYB) was studied using Ag(+) doped TiO(2) under UV irradiation in a batch reactor. Catalytic dose, initial concentration of dye and pH of the reaction mixture were found to influence the degradation process most. The degradation was found to be effective in the range catalytic dose (0.5-1.5g/L), initial dye concentration (25-100ppm) and pH of reaction mixture (5-9). Using the three factors three levels Box-Behnken design of experiment technique 15 sets of experiments were designed considering the effective ranges of the influential parameters. The results of the experiments were fitted to two quadratic polynomial models developed using response surface methodology (RSM), representing functional relationship between the decolorization and mineralization of MYB and the experimental parameters. Design Expert software version 8.0.6.1 was used to optimize the effects of the experimental parameters on the responses. The optimum values of the parameters were dose of Ag(+) doped TiO(2) 0.99g/L, initial concentration of MYB 57.68ppm and pH of reaction mixture 7.76. Under the optimal condition the predicted decolorization and mineralization rate of MYB were 95.97% and 80.33%, respectively. Regression analysis with R(2) values >0.99 showed goodness of fit of the experimental results with predicted values. Copyright © 2012 Elsevier B.V. All rights reserved.

Resting-state functional magnetic resonance imaging for surgical planning in pediatric patients: a preliminary experience.

PubMed

Roland, Jarod L; Griffin, Natalie; Hacker, Carl D; Vellimana, Ananth K; Akbari, S Hassan; Shimony, Joshua S; Smyth, Matthew D; Leuthardt, Eric C; Limbrick, David D

2017-12-01

OBJECTIVE Cerebral mapping for surgical planning and operative guidance is a challenging task in neurosurgery. Pediatric patients are often poor candidates for many modern mapping techniques because of inability to cooperate due to their immature age, cognitive deficits, or other factors. Resting-state functional MRI (rs-fMRI) is uniquely suited to benefit pediatric patients because it is inherently noninvasive and does not require task performance or significant cooperation. Recent advances in the field have made mapping cerebral networks possible on an individual basis for use in clinical decision making. The authors present their initial experience translating rs-fMRI into clinical practice for surgical planning in pediatric patients. METHODS The authors retrospectively reviewed cases in which the rs-fMRI analysis technique was used prior to craniotomy in pediatric patients undergoing surgery in their institution. Resting-state analysis was performed using a previously trained machine-learning algorithm for identification of resting-state networks on an individual basis. Network maps were uploaded to the clinical imaging and surgical navigation systems. Patient demographic and clinical characteristics, including need for sedation during imaging and use of task-based fMRI, were also recorded. RESULTS Twenty patients underwent rs-fMRI prior to craniotomy between December 2013 and June 2016. Their ages ranged from 1.9 to 18.4 years, and 12 were male. Five of the 20 patients also underwent task-based fMRI and one underwent awake craniotomy. Six patients required sedation to tolerate MRI acquisition, including resting-state sequences. Exemplar cases are presented including anatomical and resting-state functional imaging. CONCLUSIONS Resting-state fMRI is a rapidly advancing field of study allowing for whole brain analysis by a noninvasive modality. It is applicable to a wide range of patients and effective even under general anesthesia. The nature of resting-state analysis precludes any need for task cooperation. These features make rs-fMRI an ideal technology for cerebral mapping in pediatric neurosurgical patients. This review of the use of rs-fMRI mapping in an initial pediatric case series demonstrates the feasibility of utilizing this technique in pediatric neurosurgical patients. The preliminary experience presented here is a first step in translating this technique to a broader clinical practice.

Transvaginal laparoscopically assisted endoscopic cholecystectomy: preliminary clinical results for a series of 43 cases in China.

PubMed

Niu, Jun; Song, Wei; Yan, Ming; Fan, Wei; Niu, Weibo; Liu, Enyu; Peng, Cheng; Lin, Pengfei; Li, Peng; Khan, Abdul Qadir

2011-04-01

Transvaginal cholecystectomy has been performed successfully at several research institutions worldwide using natural orifice transluminal endoscopic surgery (NOTES) techniques. However, it is a growing new surgical concept in China. Several technical challenges hinder the safe clinical application of NOTES. This study investigated transvaginal endoscopic cholecystectomy performed with the assistance of a single umbilical trocar and achieved helpful initial clinical experience. From May 2009 to April 2010, a total of 43 transvaginal human cholecystectomies were performed. A single umbilical trocar was used for safe access and laparoscopic assistance during the operation. After the gallbladder had been removed through the vagina, the colpotomy was closed with absorbable stitches under direct vision. In addition, Student's t-test was performed for two samples to estimate the superiority of NOTES over a conventional laparoscopic cholecystectomy (LC) operation. The procedure was successfully completed for all the patients. No intra- or post-operative complications occurred. The patients recovered promptly after surgery, and all were satisfied with ideal cosmetic outcomes. The postoperative pain, hospital stay, and cost of hospitalization with NOTES were much less than with conventional LC operations. Although endoscopic instruments specifically designed for NOTES are not available, the addition of an umbilical trocar is an optimal way to allow safe performance of NOTES procedures in an easily reproducible manner. The authors' initial experience demonstrates that this hybrid technique is potentially feasible and effective for reducing postoperative pain and recovery times while improving the cosmetic results of transvaginal cholecystectomy.

STUDIES ON THE SENSITIZATION OF ANIMALS WITH SIMPLE CHEMICAL COMPOUNDS

PubMed Central

Maguire, Henry C.; Chase, Merrill W.

1972-01-01

A method of establishing regular and intense sensitivity to picric acid is described, based upon an initial sensitization by a "split-adjuvant" technique in which the intradermal injection of mycobacteria in paraffin oil precedes or follows the administration of allergen to the same sites. When subsequent contact applications of picric acid are later made, the degree of sensitivity rises in steps such that reactivity occurs in tests made with low concentrations of picric acid, in the range of 0.06–0.006% but varying somewhat from one experiment to another. This heightening of picric acid reactivity represents an anamnestic response in the area of delayed hypersensitivity. The characteristics of contact reactions to the weak allergen, picric acid, differ from those encountered with covalently binding haptens, PCI and DNCB. A slow evolution from an initial micropapular reaction to full reaction requires about 3 days, leading often to a micaceous scale, with histological evidence of vesiculation even while the reaction is still feeble, and to an infiltrate containing a significant number of polymorphonuclear leukocytes. Substitution of an emulsion of picric acid in complete Freund's adjuvant as a priming experience proved to be much less efficient. The split-adjuvant technique offers a general plan for sensitizing with weak allergens. Indeed, technically, sensitization can be acquired even when, for priming, the allergen is applied topically over intradermal depots of mycobacteria in paraffin oil. Compatibility between sensitizer and adjuvant is not required. PMID:5060294

Robot-Assisted Laparoendoscopic Single-Site Partial Nephrectomy With the Novel Da Vinci Single-Site Platform: Initial Experience

PubMed Central

Komninos, Christos; Tuliao, Patrick; Kim, Dae Keun; Choi, Young Deuk; Chung, Byung Ha

2014-01-01

Purpose To report our initial clinical cases of robotic laparoendoscopic single-site (R-LESS) partial nephrectomy (PN) performed with the use of the novel Da Vinci R-LESS platform. Materials and Methods Three patients underwent R-LESS PN from November 2013 through February 2014. Perioperative and postoperative outcomes were collected and intraoperative difficulties were noted. Results Operative time and estimated blood loss volume ranged between 100 and 110 minutes and between 50 and 500 mL, respectively. None of the patients was transfused. All cases were completed with the off-clamp technique, whereas one case required conversion to the conventional (multiport) approach because of difficulty in creating the appropriate scope for safe tumor resection. No major postoperative complications occurred, and all tumors were resected in safe margins. Length of hospital stay ranged between 3 and 7 days. The lack of EndoWrist movements, the external collisions, and the bed assistant's limited working space were noticed to be the main drawbacks of this surgical method. Conclusions Our initial experience with R-LESS PN with the novel Da Vinci platform shows that even though the procedure is feasible, it should be applied in only appropriately selected patients. However, further improvement is needed to overcome the existing limitations. PMID:24955221

Deterministic and Probabilistic Metrics of Surface Air Temperature and Precipitation in the MiKlip Decadal Prediction System

NASA Astrophysics Data System (ADS)

Kadow, Christopher; Illing, Sebastian; Kunst, Oliver; Pohlmann, Holger; Müller, Wolfgang; Cubasch, Ulrich

2014-05-01

Decadal forecasting of climate variability is a growing need for different parts of society, industry and economy. The German initiative MiKlip (www.fona-miklip.de) focuses on the ongoing processes of medium-term climate prediction. The scientific major project funded by the Federal Ministry of Education and Research in Germany (BMBF) develops a forecast system, that aims for reliable predictions on decadal timescales. Using a single earth system model from the Max-Planck institute (MPI-ESM) and moving from the uninitialized runs on to the first initialized 'Coupled Model Intercomparison Project Phase 5' (CMIP5) hindcast experiments identified possibilities and open scientific tasks. The MiKlip decadal prediction system was improved on different aspects through new initialization techniques and datasets of the ocean and atmosphere. To accompany and emphasize such an improvement of a forecast system, a standardized evaluation system designed by the MiKlip sub-project 'Integrated data and evaluation system for decadal scale prediction' (INTEGRATION) analyzes every step of its evolution. This study aims at combining deterministic and probabilistic skill scores of this prediction system from its unitialized state to anomaly and then full-field oceanic initialization. The improved forecast skill in these different decadal hindcast experiments of surface air temperature and precipitation in the Pacific region and the complex area of the North Atlantic illustrate potential sources of skill. A standardized evaluation leads prediction systems depending on development to find its way to produce reliable forecasts. Different aspects of these research dependencies, e.g. ensemble size, resolution, initializations, etc. will be discussed.

Experience Gained from Designing Exhaust Hoods of Large Steam Turbines Using Computational Fluid Dynamics Techniques

NASA Astrophysics Data System (ADS)

Galaev, S. A.; Ris, V. V.; Smirnov, E. M.; Babiev, A. N.

2018-06-01

Experience gained from designing exhaust hoods for modernized versions of K-175/180-12.8 and K-330-23.5-1 steam turbines is presented. The hood flow path is optimized based on the results of analyzing equilibrium wet steam 3D flow fields calculated using up-to-date computation fluid dynamics techniques. The mathematical model constructed on the basis of Reynolds-averaged Navier-Stokes equations is validated by comparing the calculated kinetic energy loss with the published data on full-scale experiments for the hood used in the K-160-130 turbine produced by the Kharkiv Turbine-Generator Works. Test calculations were carried out for four turbine operation modes. The obtained results from validating the model with the K-160-130 turbine hood taken as an example were found to be equally positive with the results of the previously performed calculations of flow pattern in the K-300-240 turbine hood. It is shown that the calculated coefficients of total losses in the K-160-130 turbine hood differ from the full-scale test data by no more than 5%. As a result of optimizing the K-175/180-12.8 turbine hood flow path, the total loss coefficient has been decreased from 1.50 for the initial design to 1.05 for the best of the modification versions. The optimized hood is almost completely free from supersonic flow areas, and the flow through it has become essentially more uniform both inside the hood and at its outlet. In the modified version of the K-330-23.5-1 turbine hood, the total loss coefficient has been decreased by more than a factor of 2: from 2.3 in the hood initial design to a value of 1.1 calculated for the hood final design version and sizes adopted for developing the detailed design. Cardinally better performance of both the hoods with respect to their initial designs was achieved as a result of multicase calculations, during which the flow path geometrical characteristics were sequentially varied, including options involving its maximally possible expansion and removal of the guiding plates producing an adverse effect.

Internal and surface phenomena in metal combustion

NASA Technical Reports Server (NTRS)

Dreizin, Edward L.; Molodetsky, Irina E.; Law, Chung K.

1995-01-01

Combustion of metals has been widely studied in the past, primarily because of their high oxidation enthalpies. A general understanding of metal combustion has been developed based on the recognition of the existence of both vapor-phase and surface reactions and involvement of the reaction products in the ensuing heterogeneous combustion. However, distinct features often observed in metal particle combustion, such as brightness oscillations and jumps (spearpoints), disruptive burning, and non-symmetric flames are not currently understood. Recent metal combustion experiments using uniform high-temperature metal droplets produced by a novel micro-arc technique have indicated that oxygen dissolves in the interior of burning particles of certain metals and that the subsequent transformations of the metal-oxygen solutions into stoichiometric oxides are accompanied with sufficient heat release to cause observed brightness and temperature jumps. Similar oxygen dissolution has been observed in recent experiments on bulk iron combustion but has not been associated with such dramatic effects. This research addresses heterogeneous metal droplet combustion, specifically focusing on oxygen penetration into the burning metal droplets, and its influence on the metal combustion rate, temperature history, and disruptive burning. A unique feature of the experimental approach is the combination of the microgravity environment with a novel micro-arc Generator of Monodispersed Metal Droplets (GEMMED), ensuring repeatable formation and ignition of uniform metal droplets with controllable initial temperature and velocity. The droplet initial temperatures can be adjusted within a wide range from just above the metal melting point, which provides means to ignite droplets instantly upon entering an oxygen containing environment. Initial droplet velocity will be set equal to zero allowing one to organize metal combustion microgravity experiments in a fashion similar to usual microgravity liquid fuel droplet combustion studies. In addition, the internal compositions of rapidly quenched metal particles will be analyzed using SEM technique. Such compositions are similar to those existing during the combustion and provide new insight on metal combustion processes. The results of this experimental work will be used to model the fundamental mechanisms of metal combustion. Preliminary experimental results on Al and Zr particle combustion at normal gravity are discussed here.

Vanishing Act: Experiments on Fission Track Annealing in Monazite

NASA Astrophysics Data System (ADS)

Shipley, N. K.; Fayon, A. K.

2006-12-01

To determine the viability of monazite as a low temperature thermochronometer, we conducted fission track annealing experiments under isothermal conditions. These experiments evaluated the effects of uranium concentration and zoning on annealing rates. Fission track annealing rates in monazite were also compared to those in Durango apatite. Preliminary results indicate that monazite grains with higher initial track densities anneal at faster rates than those with low initial densities and that fission tracks in monazite anneal at a faster rate than those in apatite. Monazite sand grains were selected from a placer sand deposit, mounted in teflon, and polished. Grains were imaged with electron backscattering to characterize zoning patterns and variations in uranium concentration. Monazite grain mounts were etched in boiling 37% HCl for 50 minutes and fission track densities were determined using standard fission track counting techniques. Durango apatite was etched in 5N HNO3 at room temperature for 20 seconds. After the initial track densities were determined, mounts in one group were annealed at 150 ° C for 1to 6 h. The mounts in a second group were annealed at 200 ° C for 2 hour periods along with mounts of Durango apatite grains. All grains were re-polished prior to each anneal. Upon completion of the experiment, backscatter images were taken of grains from which fission track counts were obtained to verify continuance of concentric zoning. Results of these experiments indicate that annealing rates of fission tracks in monazite vary as a function of uranium concentration. Uranium concentration was constrained on the basis of zoning patterns obtained from electron backscatter images. Fission track densities in grains with initial track densities of approximately 2.4 × 106 tracks/cm2 were reduced at average rate of 16% every two hours. In contrast, track densities in grains with initial track densities of approximately 1.6 × 106 tracks/cm2 average 4.6% density reduction every two hours. In both cases, track density reduction in monazite was faster than the rate of 0.1 % every two hours obtained for apatite. This would indicate that fission track annealing occurs at a lower temperature in monazite than in apatite. Thus monazite would be useful as a low temperature chronometer for determining cooling histories in recently exhumed rocks.

Biomechanical comparison between the rectangular-tunnel and the round-tunnel anterior cruciate ligament reconstruction procedures with a bone-patellar tendon-bone graft.

PubMed

Suzuki, Tomoyuki; Shino, Konsei; Otsubo, Hidenori; Suzuki, Daisuke; Mae, Tatsuo; Fujimiya, Mineko; Yamashita, Toshihiko; Fujie, Hiromichi

2014-10-01

The purpose of this study was to evaluate the effectiveness of 2 anterior cruciate ligament (ACL) reconstruction techniques using a bone-patellar tendon-bone (BPTB) graft with femoral tunnel, either a rectangular tunnel (RET) or a round tunnel (ROT). For experiment 1, nine fresh-frozen human cadaveric knees were tested with a robotic/universal force-moment sensor system to determine the initial optimal tension: the amount of graft tension at 15° of flexion most closely resembling the anterior laxity of a normal knee. The value was estimated by repeatedly measuring anterior laxity when 100 N of anteroposterior drawer load was applied to the knees at 30° of flexion after RET ACL or ROT ACL reconstruction. For experiment 2, six fresh-frozen human cadaveric knees were selected. On the basis of the initial tension determined in experiment 1, RET ACL reconstruction was conducted with the graft tensioned to 10 N, followed by ROT ACL reconstruction on the same knee at 40 N of initial tension, and the biomechanical efficacy of the 2 methods was compared. For experiment 1, the mean laxity match tension at 15° of flexion was 8.6 ± 4.8 N and 34.8 ± 9.2 N for RET- and ROT-reconstructed knees, respectively. For experiment 2, both RET and ROT ACL reconstructions were successful in controlling anterior tibial translation under anterior tibial loads, with the graft initially tensioned to 10 N in the former and to 40 N in the latter. However, the greater tensioning in ROT reconstruction led to proximal, posterior, and lateral displacement of the tibia along with its external and valgus rotation. The RET ACL-reconstructed knee more closely resembled the normal knee in biomechanical behavior. Although ROT reconstruction successfully controlled anterior translation with greater initial tensioning to the graft, the normal positional relation between the tibia and femur was impaired. Rectangular femoral ACL fixation constructs and grafts may prove more efficacious at restoring in vivo ACL kinematics than round femoral tunnels. Copyright © 2014 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Time dependency of the prediction skill for the North Atlantic subpolar gyre in initialized decadal hindcasts with MPI-ESM

NASA Astrophysics Data System (ADS)

Brune, Sebastian; Düsterhus, Andre; Pohlmann, Holger; Müller, Wolfgang; Baehr, Johanna

2017-04-01

We analyze the time dependency of decadal hindcast skill in the North Atlantic subpolar gyre within the time period 1961-2013. We compare anomaly correlation coefficients and interquartile ranges of total upper ocean heat content and sea surface temperature for three differently initialized sets of hindcast simulations with the global coupled model MPI-ESM. All initializations use weakly coupled assimilation with the same full-field nudging in the atmospheric component and different assimilation techniques for oceanic temperature and salinity: (1) ensemble Kalman filter assimilating EN4 and HadISST observations, (2) nudging of anomalies to ORAS4 reanalysis, (3) nudging of full values to ORAS4 reanalysis. We find that hindcast skill depends strongly on the evaluation time period, with higher hindcast skill during strong multiyear trends and lower hindcast skill in the absence of such trends. While there may only be small differences between the prediction systems in the analysis focusing on the entire hindcast period, these differences between the hindcast systems are much more pronounced when investigating any 20-year subperiod within the entire hindcast period. For the ensemble Kalman filter high skill in the assimilation experiment is generally linked to high skill in the initialized hindcasts. Such direct link does not seem to exist in the hindcasts initialized by either nudged system. In the ensemble Kalman filter initialized hindcasts, we find significant hindcast skill for up to 5 to 8 lead years, except for the 1970s. In the nudged system initialized hindcasts, hindcast skill is consistently diminished in lead years 2 and 3 with lowest skill in the 1970s as well. Overall, we find that a model-consistent assimilation technique can improve hindcast skill. Further, the evaluation of 20 year subperiods within the full hindcast period provides essential insights to judge the success of both the assimilation and the subsequent hindcast skill.

Isotopic disproportionation during hydrogen isotopic analysis of nitrogen-bearing organic compounds

USGS Publications Warehouse

Nair, Sreejesh; Geilmann, Heike; Coplen, Tyler B.; Qi, Haiping; Gehre, Matthias; Schimmelmann, Arndt; Brand, Willi A.

2015-01-01

Rationale High-precision hydrogen isotope ratio analysis of nitrogen-bearing organic materials using high-temperature conversion (HTC) techniques has proven troublesome in the past. Formation of reaction products other than molecular hydrogen (H2) has been suspected as a possible cause of incomplete H2 yield and hydrogen isotopic fractionation. Methods The classical HTC reactor setup and a modified version including elemental chromium, both operated at temperatures in excess of 1400 °C, have been compared using a selection of nitrogen-bearing organic compounds, including caffeine. A focus of the experiments was to avoid or suppress hydrogen cyanide (HCN) formation and to reach quantitative H2 yields. The technique also was optimized to provide acceptable sample throughput. Results The classical HTC reaction of a number of selected compounds exhibited H2 yields from 60 to 90 %. Yields close to 100 % were measured for the experiments with the chromium-enhanced reactor. The δ2H values also were substantially different between the two types of experiments. For the majority of the compounds studied, a highly significant relationship was observed between the amount of missing H2and the number of nitrogen atoms in the molecules, suggesting the pyrolytic formation of HCN as a byproduct. A similar linear relationship was found between the amount of missing H2 and the observed hydrogen isotopic result, reflecting isotopic fractionation. Conclusions The classical HTC technique to produce H2 from organic materials using high temperatures in the presence of glassy carbon is not suitable for nitrogen-bearing compounds. Adding chromium to the reaction zone improves the yield to 100 % in most cases. The initial formation of HCN is accompanied by a strong hydrogen isotope effect, with the observed hydrogen isotope results on H2 being substantially shifted to more negative δ2H values. The reaction can be understood as an initial disproportionation leading to H2 and HCN with the HCN-hydrogen systematically enriched in 2H by more than 50 ‰. In the reaction of HCN with chromium, H2 and chromium-containing solid residues are formed quantitatively.

Preliminary design of laser-induced breakdown spectroscopy for proto-Material Plasma Exposure eXperiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaw, G., E-mail: shawgc@ornl.gov; University of Tennessee, Knoxville, Tennessee 37996; Martin, M. Z.

2014-11-15

Laser-induced breakdown spectroscopy (LIBS) is a technique for measuring surface matter composition. LIBS is performed by focusing laser radiation onto a target surface, ablating the surface, forming a plasma, and analyzing the light produced. LIBS surface analysis is a possible diagnostic for characterizing plasma-facing materials in ITER. Oak Ridge National Laboratory has enabled the initial installation of a laser-induced breakdown spectroscopy diagnostic on the prototype Material-Plasma Exposure eXperiment (Proto-MPEX), which strives to mimic the conditions found at the surface of the ITER divertor. This paper will discuss the LIBS implementation on Proto-MPEX, preliminary design of the fiber optic LIBS collectionmore » probe, and the expected results.« less

Direct Trocar Insertion with Elevation of the Rectus Sheath in Bariatric Surgery: A Novel Technique.

PubMed

Habibi, Mani; Seyit, Hakan; Kones, Osman; Kartal, Bahadir; Alis, Halil

2017-12-30

Initial trocar entry, the first step in laparoscopic surgery, is associated with several complications. In morbidly obese patients, initial trocar placement is associated with a greater number of complications compared to non-obese patients. Materials and Surgical Technique. In this study, we describe our use of an initial trocar entry technique which is direct trocar insertion with elevation of the rectus sheath by a single Backhaus towel clamp and we would like to evaluate the sa fety and efficacy of its administration in bariatric surgery. Our results indicate that gaining initial trocar entry using our technique leads to successful laparoscopic bariatric surgery. Our technique is a safe, effective, and reliable first step in successful laparoscopic surgery for almost all patients, and is only contraindicated in patients with severe hepatomegaly.

Design Tool Using a New Optimization Method Based on a Stochastic Process

NASA Astrophysics Data System (ADS)

Yoshida, Hiroaki; Yamaguchi, Katsuhito; Ishikawa, Yoshio

Conventional optimization methods are based on a deterministic approach since their purpose is to find out an exact solution. However, such methods have initial condition dependence and the risk of falling into local solution. In this paper, we propose a new optimization method based on the concept of path integrals used in quantum mechanics. The method obtains a solution as an expected value (stochastic average) using a stochastic process. The advantages of this method are that it is not affected by initial conditions and does not require techniques based on experiences. We applied the new optimization method to a hang glider design. In this problem, both the hang glider design and its flight trajectory were optimized. The numerical calculation results prove that performance of the method is sufficient for practical use.

The impact of transfer from hemodialysis on peritoneal dialysis technique survival.

PubMed

Nessim, Sharon J; Bargman, Joanne M; Jassal, S Vanita; Oliver, Matthew J; Na, Yingbo; Perl, Jeffrey

2015-01-01

A significant proportion of peritoneal dialysis (PD) patients receive an initial period of hemodialysis (HD) before transitioning to PD ("PD-switch"). We sought to better understand the risks of PD technique failure (TF) and mortality for those patients compared with patients starting with PD as their first dialysis modality ("PD-first"). Using Canadian Organ Replacement Register data, we compared the risk of PD TF between PD-first and PD-switch patients within the first year after HD initiation. In a secondary analysis, the PD-switch patients were stratified into three groups based on timing of the switch from initial HD to PD as follows: 0 - 90 days, 91 - 180 days, and 181 - 365 days. Each group was compared with PD-first patients for risk of PD TF and death. Between 2001 and 2010, 9404 patients initiated PD as their first renal replacement therapy, and 3757 switched from HD to PD. After multivariable adjustment, the risk of PD TF was higher among PD-switch patients than among PD-first patients [adjusted hazard ratio (AHR): 1.37; 95% confidence interval (CI): 1.26 to 1.49], particularly within the first year after the switch from HD to PD (AHR: 1.51; 95% CI: 1.36 to 1.68). There was no association between time on HD within the first year and subsequent risk of PD TF. For all the stratified PD-switch groups, death rates were higher than those for PD-first patients. Compared with patients who start renal replacement therapy with PD, those who transfer from HD to PD within the first year on dialysis experience higher rates of PD TF and death, with the highest risk being observed in the initial year after the switch to PD. Copyright © 2015 International Society for Peritoneal Dialysis.

Advanced flight hardware for organic separations

NASA Astrophysics Data System (ADS)

Deuser, Mark S.; Vellinger, John C.; Weber, John T.

1997-01-01

Aqueous Two-Phase Partitioning (ATPP) is a unique separation technique which allows purification and classification of biological materials. SHOT has employed the ATPP process in separation equipment developed for both space and ground applications. Initial equipment development and research focused on the ORganic SEParation (ORSEP) space flight experiments that were performed on suborbital rockets and the shuttle. ADvanced SEParations (ADSEP) technology was developed as the next generation of ORSEP equipment through a NASA Small Business Innovation Research (SBIR) contract. Under the SBIR contract, a marketing study was conducted, indicating a growing commercial market exists among biotechnology firms for ADSEP equipment and associated flight research and development services. SHOT is preparing to begin manufacturing and marketing laboratory versions of the ADSEP hardware for the ground-based market. In addition, through a self-financed SBIR Phase III effort, SHOT fabricated and integrated the ADSEP flight hardware for a commercially-driven flight experiment as the initial step in marketing space processing services. The ADSEP ground-based and microgravity research is expected to play a vital role in developing important new biomedical and pharmaceutical products.

Evaluation of chest tomosynthesis for the detection of pulmonary nodules: effect of clinical experience and comparison with chest radiography

NASA Astrophysics Data System (ADS)

Zachrisson, Sara; Vikgren, Jenny; Svalkvist, Angelica; Johnsson, Åse A.; Boijsen, Marianne; Flinck, Agneta; Månsson, Lars Gunnar; Kheddache, Susanne; Båth, Magnus

2009-02-01

Chest tomosynthesis refers to the technique of collecting low-dose projections of the chest at different angles and using these projections to reconstruct section images of the chest. In this study, a comparison of chest tomosynthesis and chest radiography in the detection of pulmonary nodules was performed and the effect of clinical experience of chest tomosynthesis was evaluated. Three senior thoracic radiologists, with more than ten years of experience of chest radiology and 6 months of clinical experience of chest tomosynthesis, acted as observers in a jackknife free-response receiver operating characteristics (JAFROC-1) study, performed on 42 patients with and 47 patients without pulmonary nodules examined with both chest tomosynthesis and chest radiography. MDCT was used as reference and the total number of nodules found using MDCT was 131. To investigate the effect of additional clinical experience of chest tomosynthesis, a second reading session of the tomosynthesis images was performed one year after the initial one. The JAFROC-1 figure of merit (FOM) was used as the principal measure of detectability. In comparison with chest radiography, chest tomosynthesis performed significantly better with regard to detectability. The observer-averaged JAFROC-1 FOM was 0.61 for tomosynthesis and 0.40 for radiography, giving a statistically significant difference between the techniques of 0.21 (p<0.0001). The observer-averaged JAFROC-1 FOM of the second reading of the tomosynthesis cases was not significantly higher than that of the first reading, indicating no improvement in detectability due to additional clinical experience of tomosynthesis.

An Eulerian time filtering technique to study large-scale transient flow phenomena

NASA Astrophysics Data System (ADS)

Vanierschot, Maarten; Persoons, Tim; van den Bulck, Eric

2009-10-01

Unsteady fluctuating velocity fields can contain large-scale periodic motions with frequencies well separated from those of turbulence. Examples are the wake behind a cylinder or the processing vortex core in a swirling jet. These turbulent flow fields contain large-scale, low-frequency oscillations, which are obscured by turbulence, making it impossible to identify them. In this paper, we present an Eulerian time filtering (ETF) technique to extract the large-scale motions from unsteady statistical non-stationary velocity fields or flow fields with multiple phenomena that have sufficiently separated spectral content. The ETF method is based on non-causal time filtering of the velocity records in each point of the flow field. It is shown that the ETF technique gives good results, similar to the ones obtained by the phase-averaging method. In this paper, not only the influence of the temporal filter is checked, but also parameters such as the cut-off frequency and sampling frequency of the data are investigated. The technique is validated on a selected set of time-resolved stereoscopic particle image velocimetry measurements such as the initial region of an annular jet and the transition between flow patterns in an annular jet. The major advantage of the ETF method in the extraction of large scales is that it is computationally less expensive and it requires less measurement time compared to other extraction methods. Therefore, the technique is suitable in the startup phase of an experiment or in a measurement campaign where several experiments are needed such as parametric studies.

Selective Transcatheter Arterial Embolization for Treatment of Bleeding Complications or Reduction of Tumor Mass of Hepatocellular Adenomas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdogan, Deha; Delden, Otto M. van; Busch, Olivier R. C.

2007-11-15

Hepatocellular adenomas (HCAs) are benign liver lesions which may be complicated by spontaneous intratumoral bleeding, with or without rupture into the abdominal cavity, or malignant degeneration. Recent advances in radiological interventional techniques now offer selective transcatheter arterial embolization (TAE) as an alternative approach to surgery as the initial treatment to stop the bleeding or as an elective treatment to reduce the tumor mass of the HCA. Herein, we report our initial experience using TAE in the management of HCA. Five female patients and one male patient presented with spontaneous hemorrhage of HCA. Four patients were initially treated with selective TAEmore » to stop the bleeding. In two patients in whom the bleeding stopped spontaneously, TAE was electively undertaken 1 year after presentation to reduce the tumor mass of HCAs >5 cm. Selective TAE as initial treatment in patients with spontaneous bleeding of HCA with or without rupture is effective and will change the need for urgent laparotomy to control bleeding. Selective TAE may also be used as an elective treatment to reduce the tumor mass of larger HCAs.« less

Cluster-cluster clustering

NASA Technical Reports Server (NTRS)

Barnes, J.; Dekel, A.; Efstathiou, G.; Frenk, C. S.

1985-01-01

The cluster correlation function xi sub c(r) is compared with the particle correlation function, xi(r) in cosmological N-body simulations with a wide range of initial conditions. The experiments include scale-free initial conditions, pancake models with a coherence length in the initial density field, and hybrid models. Three N-body techniques and two cluster-finding algorithms are used. In scale-free models with white noise initial conditions, xi sub c and xi are essentially identical. In scale-free models with more power on large scales, it is found that the amplitude of xi sub c increases with cluster richness; in this case the clusters give a biased estimate of the particle correlations. In the pancake and hybrid models (with n = 0 or 1), xi sub c is steeper than xi, but the cluster correlation length exceeds that of the points by less than a factor of 2, independent of cluster richness. Thus the high amplitude of xi sub c found in studies of rich clusters of galaxies is inconsistent with white noise and pancake models and may indicate a primordial fluctuation spectrum with substantial power on large scales.

Next generation initiation techniques

NASA Technical Reports Server (NTRS)

Warner, Tom; Derber, John; Zupanski, Milija; Cohn, Steve; Verlinde, Hans

1993-01-01

Four-dimensional data assimilation strategies can generally be classified as either current or next generation, depending upon whether they are used operationally or not. Current-generation data-assimilation techniques are those that are presently used routinely in operational-forecasting or research applications. They can be classified into the following categories: intermittent assimilation, Newtonian relaxation, and physical initialization. It should be noted that these techniques are the subject of continued research, and their improvement will parallel the development of next generation techniques described by the other speakers. Next generation assimilation techniques are those that are under development but are not yet used operationally. Most of these procedures are derived from control theory or variational methods and primarily represent continuous assimilation approaches, in which the data and model dynamics are 'fitted' to each other in an optimal way. Another 'next generation' category is the initialization of convective-scale models. Intermittent assimilation systems use an objective analysis to combine all observations within a time window that is centered on the analysis time. Continuous first-generation assimilation systems are usually based on the Newtonian-relaxation or 'nudging' techniques. Physical initialization procedures generally involve the use of standard or nonstandard data to force some physical process in the model during an assimilation period. Under the topic of next-generation assimilation techniques, variational approaches are currently being actively developed. Variational approaches seek to minimize a cost or penalty function which measures a model's fit to observations, background fields and other imposed constraints. Alternatively, the Kalman filter technique, which is also under investigation as a data assimilation procedure for numerical weather prediction, can yield acceptable initial conditions for mesoscale models. The third kind of next-generation technique involves strategies to initialize convective scale (non-hydrostatic) models.

An interactive user-friendly approach to surface-fitting three-dimensional geometries

NASA Technical Reports Server (NTRS)

Cheatwood, F. Mcneil; Dejarnette, Fred R.

1988-01-01

A surface-fitting technique has been developed which addresses two problems with existing geometry packages: computer storage requirements and the time required of the user for the initial setup of the geometry model. Coordinates of cross sections are fit using segments of general conic sections. The next step is to blend the cross-sectional curve-fits in the longitudinal direction using general conics to fit specific meridional half-planes. Provisions are made to allow the fitting of fuselages and wings so that entire wing-body combinations may be modeled. This report includes the development of the technique along with a User's Guide for the various menus within the program. Results for the modeling of the Space Shuttle and a proposed Aeroassist Flight Experiment geometry are presented.

Technique for Periarticular Local Infiltrative Anesthesia Delivery Using Liposomal Bupivacaine in Total Knee Arthroplasty.

PubMed

Connelly, Jacob O; Edwards, Paul K; Mears, Simon C; Barnes, C Lowry

2015-01-01

Postoperative pain control after total knee arthroplasty is a major contributing factor to patient satisfaction, rehabilitation, and length of stay. Current clinical practice guidelines recommend a multimodal pain management protocol, including the use of regional anesthesia. Periarticular injection (PAI) has been shown to provide excellent pain relief after total knee arthroplasty. Recently, liposomal bupivacaine has been introduced as a long-acting alternative to traditional local anesthetics, such as bupivacaine or ropivacaine. Liposomal bupivacaine is a sustained-release preparation designed to provide local analgesia up to 72 hours after initial application. The efficacy of PAI relies significantly on a meticulous, systematic injection technique. This article details recommendations for solution preparation and injection during total knee arthroplasty on the basis of the experience of a high-volume orthopaedic reconstruction service.

On-line identification of lysergic acid diethylamide (LSD) in tablets using a combination of a sweeping technique and micellar electrokinetic chromatography/77 K fluorescence spectroscopy.

PubMed

Fang, Ching; Liu, Ju-Tsung; Lin, Cheng-Huang

2003-03-01

This work describes a novel method for the accurate determination of lysergic acid diethylamide (LSD) in tablets. A technique involving sweeping-micellar electrokinetic chromatography (MEKC) was used for the initial on-line concentration and separation, after which a cryogenic molecular fluorescence experiment was performed at 77 K. Using this approach, not only the separation of LSD from the tablet extract was achieved, but on-line spectra were readily distinguishable and could be unambiguously assigned. The results are in agreement with analyses by gas chromatography-mass spectrometry (GC-MS). Thus, this method, which was found to be accurate, sensitive and rapid, has the potential for use as a reliable complementary method to GC-MS in such analyses.

Innovative acoustic technique for studying new materials and new developments in solid state physics

NASA Astrophysics Data System (ADS)

Maynard, Julian D.

1993-10-01

The goals of this project involve the use of innovative acoustic techniques to study new materials and new developments in solid state physics, such as effects in mesoscopic electronic systems. Major accomplishments include (1) the preparation and publication of a number of major papers and chapters in books, (2) the comparison of the anisotropy of an aluminum alloy quasicrystal with that of its cubic approximant, (3) the measurement of the elastic constants of a diamond substitute material, TiB2, (4) the measurement of an extremely low (possibly the lowest) infrared optical-absorption coefficient, (5) the measurement of the effects of disorder on the propagation of a nonlinear pulse, and (6) the acquisition of initial data in an experiment on the onset of fracture.

Quantification of Soluble Sugars and Sugar Alcohols by LC-MS/MS.

PubMed

Feil, Regina; Lunn, John Edward

2018-01-01

Sugars are simple carbohydrates composed primarily of carbon, hydrogen, and oxygen. They play a central role in metabolism as sources of energy and as building blocks for synthesis of structural and nonstructural polymers. Many different techniques have been used to measure sugars, including refractometry, colorimetric and enzymatic assays, gas chromatography, high-performance liquid chromatography, and nuclear magnetic resonance spectroscopy. In this chapter we describe a method that combines an initial separation of sugars by high-performance anion-exchange chromatography (HPAEC) with detection and quantification by tandem mass spectrometry (MS/MS). This combination of techniques provides exquisite specificity, allowing measurement of a diverse range of high- and low-abundance sugars in biological samples. This method can also be used for isotopomer analysis in stable-isotope labeling experiments to measure metabolic fluxes.

The use of artificial neural network for modeling the decolourization of acid orange 7 solution of industrial by ozonation process

NASA Astrophysics Data System (ADS)

Fatimah, S.; Wiharto, W.

2017-02-01

Acid Orange 7 (AO7) is one of the synthetic dye in the dyeing process in the textile industry. The use of this dye can produce wastewater which will be endangered if not treated well. Ozonation method is one technique to solve this problem. Ozonation is a waste processing techniques using ozone as an oxidizing agent. Variables used in this research is the ozone concentration, the initial concentration of AO7, temperature, and pH. Based on the experimental result that the optimum value decolourization percentage is 80% when the ozone concentration is 560 mg/L, the initial concentration AO7 is 14 mg/L, the temperature is 390 °C, and pH is 7,6. Decolourization efficiency of experimental results and predictions successfully modelled by the neural network architecture. The data used to construct a neural network architecture quasi newton one step secant as many as 31 data. A comparison between the predicted results of the designed ANN models and experiment was conducted. From the modeling results obtained MAPE value of 0.7763%. From the results of this artificial neural network architecture obtained the optimum value decolourization percentage in 80,64% when the concentration of ozone is 550 mg/L, the initial concentration AO7 is 11 mg/L, the temperature is 41 °C, and the pH is 7.9.

Review of methods to probe single cell metabolism and bioenergetics

DOE PAGES

Vasdekis, Andreas E.; Stephanopoulos, Gregory

2014-10-31

The sampling and manipulation of cells down to the individual has been of substantial interest since the very beginning of Life Sciences. Herein, our objective is to highlight the most recent developments in single cell manipulation, as well as pioneering ones. First, flow-through methods will be discussed, namely methods in which the single cells flow continuously in an ordered manner during their analysis. This section will be followed by confinement techniques that enable cell isolation and confinement in one, two- or three-dimensions. Flow cytometry and droplet microfluidics are the two most common methods of flow-through analysis. While both are high-throughputmore » techniques, their difference lays in the fact that the droplet encapsulated cells experience a restricted and personal microenvironment, while in flow cytometry cells experience similar nutrient and stimuli initial concentrations. These methods are rather well established; however, they recently enabled immense strides in single cell phenotypic analysis, namely the identification and analysis of metabolically distinct individuals from an isogenic population using both droplet microfluidics and flow cytometry.« less

Growth rate measurement in free jet experiments

NASA Astrophysics Data System (ADS)

Charpentier, Jean-Baptiste; Renoult, Marie-Charlotte; Crumeyrolle, Olivier; Mutabazi, Innocent

2017-07-01

An experimental method was developed to measure the growth rate of the capillary instability for free liquid jets. The method uses a standard shadow-graph imaging technique to visualize a jet, produced by extruding a liquid through a circular orifice, and a statistical analysis of the entire jet. The analysis relies on the computation of the standard deviation of a set of jet profiles, obtained in the same experimental conditions. The principle and robustness of the method are illustrated with a set of emulated jet profiles. The method is also applied to free falling jet experiments conducted for various Weber numbers and two low-viscosity solutions: a Newtonian and a viscoelastic one. Growth rate measurements are found in good agreement with linear stability theory in the Rayleigh's regime, as expected from previous studies. In addition, the standard deviation curve is used to obtain an indirect measurement of the initial perturbation amplitude and to identify beads on a string structure on the jet. This last result serves to demonstrate the capability of the present technique to explore in the future the dynamics of viscoelastic liquid jets.

Growth and characterization of binary and pseudo-binary 3-5 compounds exhibiting non-linear optical behavior. Undergraduate research opportunities in microgravity science and technology

NASA Technical Reports Server (NTRS)

Witt, August F.

1992-01-01

In line with the specified objectives, a Bridgman-type growth configuration in which unavoidable end effects - conventionally leading to growth interface relocation - are compensated by commensurate input-power changes is developed; the growth rate on a microscale is predictable and unaffected by changes in heat transfer conditions. To permit quantitative characterization of the growth furnace cavity (hot-zone), a 3-D thermal field mapping technique, based on the thermal image, is being tested for temperatures up to 1100 C. Computational NIR absorption analysis was modified to now permit characterization of semi-insulating single crystals. Work on growth and characterization of bismuth-silicate was initiated. Growth of BSO (B12SiO20) for seed material by the Czochralski technique is currently in progress. Undergraduate research currently in progress includes: ground based measurements of the wetting behavior (contact angles) of semiconductor melts on substrates consisting of potential confinement materials for solidification experiments in a reduced gravity environment. Hardware modifications required for execution of the wetting experiments in a KC-135 facility are developed.

Initial experience with percutaneous selective embolization: A truly minimally invasive treatment of the adolescent varicocele with no risk of hydrocele development.

PubMed

Storm, Douglas W; Hogan, Mark J; Jayanthi, Venkata R

2010-12-01

Postoperative hydrocele development is a frustrating complication of varicocele surgical repair. To avoid this complication, we began to offer percutaneous embolization as a treatment option. We present our initial experience with this technique. A retrospective review of all patients who underwent percutaneous embolization and sclerotherapy of a varicocele at our institution was performed. There were 27 patients with a mean age of 16 years (range 13-19 years). Indications included pain (48%), varicocele size (30%) and persistent testicular asymmetry (22%). Four patients had experienced failure of a previous surgical repair. Follow-up data were available for 21 patients (mean 9 months). The varicocele resolved in 19 patients (91%) with no evidence of hydrocele formation in any of the boys. There was resolution of pain in all patients for whom this was the indication for the procedure. In the two failures, access to the lower spermatic vein was not possible owing to the number and tortuosity of the vessels. Percutaneous embolization and sclerotherapy represent a truly minimally invasive treatment with low morbidity, minimal pain and rapid recovery. In our early experience, since lymphatic channels are completely avoided, there appears to be no risk of hydrocele formation. Copyright © 2010 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

Spherical nanoindentation stress–strain curves

DOE PAGES

Pathak, Siddhartha; Kalidindi, Surya R.

2015-03-24

Although indentation experiments have long been used to measure the hardness and Young's modulus, the utility of this technique in analyzing the complete elastic–plastic response of materials under contact loading has only been realized in the past few years – mostly due to recent advances in testing equipment and analysis protocols. This paper provides a timely review of the recent progress made in this respect in extracting meaningful indentation stress–strain curves from the raw datasets measured in instrumented spherical nanoindentation experiments. These indentation stress–strain curves have produced highly reliable estimates of the indentation modulus and the indentation yield strength inmore » the sample, as well as certain aspects of their post-yield behavior, and have been critically validated through numerical simulations using finite element models as well as direct in situ scanning electron microscopy (SEM) measurements on micro-pillars. Much of this recent progress was made possible through the introduction of a new measure of indentation strain and the development of new protocols to locate the effective zero-point of initial contact between the indenter and the sample in the measured datasets. As a result, this has led to an important key advance in this field where it is now possible to reliably identify and analyze the initial loading segment in the indentation experiments.« less

The study of dopant segregation behavior during the growth of GaAs in microgravity

NASA Technical Reports Server (NTRS)

Matthiesen, David H.; Majewski, J. A.

1994-01-01

An investigation into the segregation behavior of selenium doped gallium arsenide during directional solidification in the microgravity environment was conducted using the Crystal Growth Furnace (CGF) aboard the first United States Microgravity Laboratory (USML-1). The two crystals grown were 1.5 cm in diameter and 16.5 cm in length with an initial melt length of 14 cm. Two translation periods were executed, the first at 2.5 microns/s and after a specified time, which was different between the two experiments, the translation rate was doubled to 5.0 microns/s. The translation was then stopped and the remaining sample melt was solidified using a gradient freeze technique in the first sample and a rapid solidification in the second experiment. Measurement of the selenium dopant distribution, using quantitative infrared transmission imaging, indicates that the first sample initially achieved diffusion controlled growth as desired. However, after about 1 cm of growth, the segregation behavior was driven from a diffusion controlled growth regime to a complete mixing regime. Measurements in the second flight sample indicated that the growth was always in a complete mixing regime. In both experiments, voids in the center line of the crystal, indicative of bubble entrapment, were found to correlate with the position in the crystal when the translation rates were doubled.

Kerr Reservoir LANDSAT experiment analysis for March 1981

NASA Technical Reports Server (NTRS)

Lecroy, S. R. (Principal Investigator)

1982-01-01

LANDSAT radiance data were used in an experiment conducted on the waters of Kerr Reservoir to determine if reliable algorithms could be developed that relate water quality parameters to remotely sensed data. A mix of different types of algorithms using the LANDSAT bands was generated to provide a thorough understanding of the relationships among the data involved. Except for secchi depth, the study demonstrated that for the ranges measured, the algorithms that satisfactorily represented the data encompass a mix of linear and nonlinear forms using only one LANDSAT band. Ratioing techniques did not improve the results since the initial design of the experiment minimized the errors against which this procedure is effective. Good correlations were found for total suspended solids, iron, turbidity, and secchi depth. Marginal correlations were discovered for nitrate and tannin + lignin. Quantification maps of Kerr Reservoir are presented for many of the water quality parameters using the developed algorithms.

Role of laser myringotomy in a pediatric otolaryngology practice: initial experience

NASA Astrophysics Data System (ADS)

Shah, Udayan K.

2001-05-01

A new technology (OtoLAM) to fenestrate the tympanic membrane with the carbon dioxide laser (CO2), in the office or the operating room, has been introduced over the last three years. While not new conceptually, this product offers the ability to easily create a precise window into the middle ear using a portable system. Controversy regarding the indications and benefits of this technique, amplified by the costs of the system and the marketing of the technology prior to extensive clinical testing, has plagued the clinical application of this technology. We report our experience over the past year with this system in a busy pediatric otolaryngology practice. Laser fenestration of the tympanic membrane has been useful for the insertion of tympanostomy tubes, and for the minimally invasive evaluation of the middle ear. Our small experience to date reveals that there is a limited role for laser tympanic membrane fenestration in a busy pediatric otolaryngology practice.

Electrophysiology for biomedical engineering students: a practical and theoretical course in animal electrocorticography.

PubMed

Albarracín, Ana L; Farfán, Fernando D; Coletti, Marcos A; Teruya, Pablo Y; Felice, Carmelo J

2016-09-01

The major challenge in laboratory teaching is the application of abstract concepts in simple and direct practical lessons. However, students rarely have the opportunity to participate in a laboratory that combines practical learning with a realistic research experience. In the Biomedical Engineering career, we offer short and optional courses to complement studies for students as they initiate their Graduation Project. The objective of these theoretical and practical courses is to introduce students to the topics of their projects. The present work describes an experience in electrophysiology to teach undergraduate students how to extract cortical information using electrocorticographic techniques. Students actively participate in some parts of the experience and then process and analyze the data obtained with different signal processing tools. In postlaboratory evaluations, students described the course as an exceptional opportunity for students interested in following a postgraduate science program and fully appreciated their contents. Copyright © 2016 The American Physiological Society.

Status and prospects of the SNO+ experiment

NASA Astrophysics Data System (ADS)

Maneira, J.

2016-05-01

The SNO+ experiment is located at the SNOLAB underground laboratory and will employ 780 tons of liquid scintillator loaded, in its initial phase, with 800 kg of 130Te (0.3% by mass) for a low-background and high-isotope-mass search for neutrino-less double beta decay. SNO+ reuses the acrylic vessel and PMT array of the SNO detector, but several experimental upgrades and adaptations were necessary to allow for the use of liquid scintillator. The SNO+ technique allows a staged approach, and extensive R&D is ongoing to increase the loadings and improve the purification of Tellurium. The very good conditions of background and low energy threshold allow SNO+ to also have other physics topics in its program, including geo- and reactor neutrinos, Supernova and solar neutrinos. This talk will describe the main advantages and challenges of the SNO+ approach for the double-beta decay program, the current status of the experiment and its sensitivity prospects.

Design and performance of the spin asymmetries of the nucleon experiment

NASA Astrophysics Data System (ADS)

Maxwell, J. D.; Armstrong, W. R.; Choi, S.; Jones, M. K.; Kang, H.; Liyanage, A.; Meziani, Z.-E.; Mulholland, J.; Ndukum, L.; Rondón, O. A.; Ahmidouch, A.; Albayrak, I.; Asaturyan, A.; Ates, O.; Baghdasaryan, H.; Boeglin, W.; Bosted, P.; Brash, E.; Brock, J.; Butuceanu, C.; Bychkov, M.; Carlin, C.; Carter, P.; Chen, C.; Chen, J.-P.; Christy, M. E.; Covrig, S.; Crabb, D.; Danagoulian, S.; Daniel, A.; Davidenko, A. M.; Davis, B.; Day, D.; Deconinck, W.; Deur, A.; Dunne, J.; Dutta, D.; El Fassi, L.; Elaasar, M.; Ellis, C.; Ent, R.; Flay, D.; Frlez, E.; Gaskell, D.; Geagla, O.; German, J.; Gilman, R.; Gogami, T.; Gomez, J.; Goncharenko, Y. M.; Hashimoto, O.; Higinbotham, D. W.; Horn, T.; Huber, G. M.; Jones, M.; Kalantarians, N.; Kang, H. K.; Kawama, D.; Keith, C.; Keppel, C.; Khandaker, M.; Kim, Y.; King, P. M.; Kohl, M.; Kovacs, K.; Kubarovsky, V.; Li, Y.; Liyanage, N.; Luo, W.; Mamyan, V.; Markowitz, P.; Maruta, T.; Meekins, D.; Melnik, Y. M.; Mkrtchyan, A.; Mkrtchyan, H.; Mochalov, V. V.; Monaghan, P.; Narayan, A.; Nakamura, S. N.; Nuruzzaman; Pentchev, L.; Pocanic, D.; Posik, M.; Puckett, A.; Qiu, X.; Reinhold, J.; Riordan, S.; Roche, J.; Sawatzky, B.; Shabestari, M.; Slifer, K.; Smith, G.; Soloviev, L.; Solvignon, P.; Tadevosyan, V.; Tang, L.; Vasiliev, A. N.; Veilleux, M.; Walton, T.; Wesselmann, F.; Wood, S. A.; Yao, H.; Ye, Z.; Zhu, L.

2018-03-01

The Spin Asymmetries of the Nucleon Experiment (SANE) performed inclusive, double-polarized electron scattering measurements of the proton at the Continuous Electron Beam Accelerator Facility at Jefferson Lab. A novel detector array observed scattered electrons of four-momentum transfer 2 . 5

The Value of Interrupted Time-Series Experiments for Community Intervention Research

PubMed Central

Biglan, Anthony; Ary, Dennis; Wagenaar, Alexander C.

2015-01-01

Greater use of interrupted time-series experiments is advocated for community intervention research. Time-series designs enable the development of knowledge about the effects of community interventions and policies in circumstances in which randomized controlled trials are too expensive, premature, or simply impractical. The multiple baseline time-series design typically involves two or more communities that are repeatedly assessed, with the intervention introduced into one community at a time. It is particularly well suited to initial evaluations of community interventions and the refinement of those interventions. This paper describes the main features of multiple baseline designs and related repeated-measures time-series experiments, discusses the threats to internal validity in multiple baseline designs, and outlines techniques for statistical analyses of time-series data. Examples are given of the use of multiple baseline designs in evaluating community interventions and policy changes. PMID:11507793

Protein crystal growth in microgravity

NASA Technical Reports Server (NTRS)

Rosenblum, William M.; Delucas, Lawrence J.; Wilson, William W.

1989-01-01

Major advances have been made in several of the experimental aspects of protein crystallography, leaving protein crystallization as one of the few remaining bottlenecks. As a result, it has become important that the science of protein crystal growth is better understood and that improved methods for protein crystallization are developed. Preliminary experiments with both small molecules and proteins indicate that microgravity may beneficially affect crystal growth. For this reason, a series of protein crystal growth experiments using the Space Shuttle was initiated. The preliminary space experiments were used to evolve prototype hardware that will form the basis for a more advanced system that can be used to evaluate effects of gravity on protein crystal growth. Various optical techniques are being utilized to monitor the crystal growth process from the incipient or nucleation stage and throughout the growth phase. The eventual goal of these studies is to develop a system which utilizes optical monitoring for dynamic control of the crystallization process.

Advances in Electrically Driven Thermal Management

NASA Technical Reports Server (NTRS)

Didion, Jeffrey R.

2017-01-01

Electrically Driven Thermal Management is a vibrant technology development initiative incorporating ISS based technology demonstrations, development of innovative fluid management techniques and fundamental research efforts. The program emphasizes high temperature high heat flux thermal management required for future generations of RF electronics and power electronic devices. This presentation reviews i.) preliminary results from the Electrohydrodynamic (EHD) Long Term Flight Demonstration launched on STP-H5 payload in February 2017 ii.) advances in liquid phase flow distribution control iii.) development of the Electrically Driven Liquid Film Boiling Experiment under the NASA Microgravity Fluid Physics Program.

Single-port robotic cholecystectomy. Initial and pioneer experience in Brazil

PubMed Central

Schraibman, Vladimir; Epstein, Marina Gabrielle; Maccapani, Gabriel Naman; Macedo, Antônio Luiz de Vasconcellos

2015-01-01

The technique of a single-port laparoscopy was developed over the last years as an attempt to lower surgical aggression and improve the aesthetic results of the minimally invasive surgery. A new robotic platform used with the da Vinci® Robotic System Single-Site System® (Intuitive Surgical, Sunnyvale, California, United States) was recently launched on the global market and is still not documented in Brazil. The authors report on the first four robotic single-port cholecystectomies performed with this da Vinci® Robotic System in Brazil. PMID:26398360

Computer simulation techniques for artificial modification of the ionosphere. Final report 31 jan 79-30 apr 81

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vance, B.; Mendillo, M.

1981-04-30

A three-dimensional model of the ionosphere was developed including chemical reactions and neutral and plasma transport. The model uses Finite Element Simulation to simulate ionospheric modification rather than solving a set of differential equations. The initial conditions of the Los Alamos Scientific Laboratory experiments, Lagopedo Uno and Dos, were input to the model, and these events were simulated. Simulation results were compared to ground and rocketborne electron-content measurements. A simulation of the transport of released SF6 was also made.

Nonlinear fracture mechanics-based analysis of thin wall cylinders

NASA Technical Reports Server (NTRS)

Brust, Frederick W.; Leis, Brian N.; Forte, Thomas P.

1994-01-01

This paper presents a simple analysis technique to predict the crack initiation, growth, and rupture of large-radius, R, to thickness, t, ratio (thin wall) cylinders. The method is formulated to deal both with stable tearing as well as fatigue mechanisms in applications to both surface and through-wall axial cracks, including interacting surface cracks. The method can also account for time-dependent effects. Validation of the model is provided by comparisons of predictions to more than forty full scale experiments of thin wall cylinders pressurized to failure.

Interferometric observations of an artificial satellite.

PubMed

Preston, R A; Ergas, R; Hinteregger, H F; Knight, C A; Robertson, D S; Shapiro, I I; Whitney, A R; Rogers, A E; Clark, T A

1972-10-27

Very-long-baseline interferometric observations of radio signals from the TACSAT synchronous satellite, even though extending over only 7 hours, have enabled an excellent orbit to be deduced. Precision in differenced delay and delay-rate measurements reached 0.15 nanosecond ( approximately 5 centimeters in equivalent differenced distance) and 0.05 picosecond per second ( approximately 0.002 centimeter per second in equivalent differenced velocity), respectively. The results from this initial three-station experiment demonstrate the feasibility of using the method for accurate satellite tracking and for geodesy. Comparisons are made with other techniques.

Proceedings of the First Workshop on Containerless Experimentation in Microgravity

NASA Technical Reports Server (NTRS)

Trinh, E. H. (Editor)

1990-01-01

The goals of the workshop were first to provide scientists an opportunity to acquaint themselves with the past, current, and future scientific investigations carried out in the Containerless Science programs of the Microgravity Science and Applications Div. of NASA, as well as ESA and Japanese Space Agencies. The second goal was to assess the technological development program for low gravity containerless experimentation instruments. The third goal was to obtain recommendations concerning rigorous but feasible new scientific and technological initiative for space experiments using noncontact sample positioning and diagnostic techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macaluso, D. A.; Bogolub, K.; Johnson, A.

Absolute single photoionization cross-section measurements of Rb 2+ ions were performed at the Advanced Light Source at Lawrence Berkeley National Laboratory using synchrotron radiation and the photo-ion, merged-beams technique. Measurements were made at a photon energy resolution of 13.5 2.5 meV from 37.31 to 44.08 eV spanning the 2 P ground state and 2 P metastable state ionization thresholds. Multiple autoionizing resonance series arising from each initial state are identified using quantum defect theory. The measurements are compared to Breit-Pauli R-matrix calculations with excellent agreement between theory and experiment.

Implementation of a 3D mixing layer code on parallel computers

NASA Technical Reports Server (NTRS)

Roe, K.; Thakur, R.; Dang, T.; Bogucz, E.

1995-01-01

This paper summarizes our progress and experience in the development of a Computational-Fluid-Dynamics code on parallel computers to simulate three-dimensional spatially-developing mixing layers. In this initial study, the three-dimensional time-dependent Euler equations are solved using a finite-volume explicit time-marching algorithm. The code was first programmed in Fortran 77 for sequential computers. The code was then converted for use on parallel computers using the conventional message-passing technique, while we have not been able to compile the code with the present version of HPF compilers.

Channeling techniques to study strains and defects in heterostructures and multi quantum wells

NASA Astrophysics Data System (ADS)

Pathak, A. P.; Dhamodaran, S.; Sathish, N.

2005-08-01

The importance and advantages of heterostructures and Quantum Wells (QWs) in device technology has made research challenging due to lack of direct techniques for their characterization. Particularly the characterization of strain and defects at the interfaces has become important due to their dominance in the electrical and optical properties of materials and devices. RBSiC has been used to study variety of defects in single crystalline materials, for nearly four decades now. Channeling based experiments play a crucial role in giving depth information of strain and defects. Ion beams are used for both material characterizations as well as for modifications. Hence it is also possible to monitor the modifications online, which are discussed in detail. In the present work, Swift Heavy Ion (SHI) modification of III-V semiconductor heterostnictures and MQWs and the results of subsequent strain measurements by RBSiC in initially strained as well as lattice matched systems are discussed. We find that the compressive strain decreases due to SHI irradiation and a tensile strain is induced in an initially lattice matched system. The incident ion fluence dependence of strain modifications in the heterostructures will also be discussed. The use of high energy channeling for better sensitivity of strain measurements in low mismatch materials will be discussed in detail. Wherever possible, a comparison of results with those obtained by other techniques like HRXRD is given.

A time-saving technique for the treatment of simple phobias.

PubMed

Bernstein, S

1999-01-01

Two cases are presented in detail and two in summary fashion to illustrate a technique that can frequently be used instead of systematic desensitization to reduce the time needed to treat simple phobias. This method combines techniques developed by Strategic Therapy and Critical Incident Debriefing. Symptoms that the patient experiences as out of control are prescribed by the therapist and then normalized. For example, a 26-year-old woman with a fear of social situations learns that it is not unusual for people to feel somewhat awkward and anxious as they try to reestablish themselves with friends after being away from them for a long period of time. Therapy taught her to accept rather than fight her initial anxiety in these situation. Another client with claustrophobia was taught to imagine himself getting anxious and telling himself, "yes, this is exactly what I expect. I am going to get anxious, and my anxiety will increase, but it isn't going to get higher than a '5' (on a 1-10 scale), and I can handle that." When these interventions are successful, the anxiety initially experienced in a phobic situation as a signal for panic is reinterpreted in new situations as expectable. This reframing renders the anxiety manageable. The treatment of two additional patients is briefly presented to further illustrate the application of this approach. Their phobias included a fear of sweating in public and a fear of sleep.

Initial operation with sodium in the Madison Dynamo Experiment.

NASA Astrophysics Data System (ADS)

Kendrick, R.; Spence, Ej; Forest, C. B.; O'Connell, R.; Nornberg, Md; Canary, Hw; Wright, A.; Robinson, K.

1999-11-01

A new liquid metal MHD experiment has been constructed at the University of Wisconsin to test several key predictions of dynamo theory: magnetic instabilities driven by sheared flow, the effects of turbulence on current generation, and the back-reaction of the self-generated magnetic field on the fluid motion which brings saturation. This presentation describes the engineering design of the experiment, which is a 0.5 m radius spherical vessel, filled with liquid sodium at 150 ^circC. The experiment is designed to achieve a magnetic Reynolds number in excess of 100, which requires approximately 80 Hp of mechanical drive, producing flow velocities in sodium of 15 m/s through impellers. Handling liquid sodium offers a number of technical challenges, but routine techniques have been developed over the past several decades for safely handling large quantities for the fast breeder reactor. The handling strategy is discussed, technical details concerning seals and pressurization are presented, and safety elements are highlighted.

A Consensus Approach to Investigate Undergraduate Pharmacy Students’ Experience of Interprofessional Education

PubMed Central

Obara, Ilona; Paterson, Alastair; Nazar, Zachariah; Portlock, Jane; Husband, Andrew

2017-01-01

Objective. To assess the development of knowledge, attitudes, and behaviors for collaborative practice among first-year pharmacy students following completion of interprofessional education. Methods. A mixed-methods strategy was employed to detect student self-reported change in knowledge, attitudes, and behaviors. Validated survey tools were used to assess student perception and attitudes. The Nominal Group Technique (NGT) was used to capture student reflections and provide peer discussion on the individual IPE sessions. Results. The validated survey tools did not detect any change in students’ attitudes and perceptions. The NGT succeeded in providing a milieu for participating students to reflect on their IPE experiences. The peer review process allowed students to compare their initial perceptions and reactions and renew their reflections on the learning experience. Conclusion. The NGT process has provided the opportunity to assess the student experience through the reflective process that was enriched via peer discussion. Students have demonstrated more positive attitudes and behaviors toward interprofessional working through IPE. PMID:28381886

Radionuclide migration: laboratory experiments with isolated fractures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rundberg, R.S.; Thompson, J.L.; Maestas, S.

Laboratory experiments examining flow and element migration in rocks containing isolated fractures have been initiated at the Los Alamos National Laboratory. Techniques are being developed to establish simple fracture flow systems which are appropriate to models using analytical solutions to the matrix diffusion-flow equations, such as those of I. Neretnieks [I. Neretnieks, Diffusion in the Rock Matrix: An Important Factor in Radionuclide Retardation? J. Geophys. Res. 85, 4379 (1980).] These experiments are intended to be intermediate steps toward larger scale field experiments where it may become more difficult to establish and control the parameters important to nuclide migration in fracturedmore » media. Laboratory experiments have been run on fractures ranging in size from 1 to 20 cm in length. The hydraulic flow in these fractures was studied to provide the effective apertures. The flows established in these fracture systems are similar to those in the granite fracture flow experiments of Witherspoon et al. [P.A. Witherspoon, J.S.Y. Wang, K. Iwai, and J.E. Gale, Validity of Cubic Law for Fluid Flow in a Deformable Rock Fracture, Lawrence Berkeley Laboratory report LBL-9557 (October 1979).] Traced solutions containing {sup 85}Sr and {sup 137}Cs were flowed through fractures in Climax Stock granite and welded tuff (Bullfrog and Tram members, Yucca Mountain, Nevada Test Site). The results of the elutions through granite agree with the matrix diffusion calculations based on independent measurements of K/sub d/. The results of the elutions through tuff, however, agree only if the K/sub d/ values used in the calculations are lower than the K/sub d/ values measured using a batch technique. This trend has been previously observed in chromatographic column experiments with tuff. 5 figures, 3 tables.« less

Sharing motherhood: biological lesbian co-mothers, a new IVF indication.

PubMed

Marina, S; Marina, D; Marina, F; Fosas, N; Galiana, N; Jové, I

2010-04-01

We herein present the initial experiences of the CEFER Institute of Reproduction in the formation of a new family model: two biological mothers, lesbians, one who provides the eggs and the other who carries the embryo in her womb. We have called this family model ROPA (Reception of Oocytes from PArtner). It is a pioneer event in Spain and among the first at a worldwide level. Fourteen lesbian couples have undergone treatment using the ROPA technique. This paper briefly describes the technique. Six pregnancies have been obtained from 13 embryo transfers. There were two miscarriages and there are three ongoing pregnancies, one of them twins. One healthy female baby was born. The following aspects are addressed: (i) legal status of lesbian couples in Western countries; (ii) the lesbian couple's access to assisted reproduction techniques; (iii) ethical aspects; (iv) medical acceptability; and (v) single mother versus lesbian mothers. In countries where the ROPA technique is legal, it offers lesbian couples a more favourable route, involving both partners, to start a family, and doctors who treat lesbian couples must be sensitive to this new family model.

Comparison of three-dimensional particle tracking and sizing using plenoptic imaging and digital in-line holography

DOE PAGES

Hall, Elise M.; Thurow, Brian S.; Guildenbecher, Daniel R.

2016-08-08

Digital in-line holography (DIH) and plenoptic photography are two techniques for single-shot, volumetric measurement of 3D particle fields. Here we present a comparison of the two methods by applying plenoptic imaging to experimental configurations that have been previously investigated with DIH. These experiments include the tracking of secondary droplets from the impact of a water drop on a thin film of water and tracking of pellets from a shotgun. Both plenoptic imaging and DIH successfully quantify the 3D nature of these particle fields. Furthermore, this includes measurement of the 3D particle position, individual particle sizes, and three-component velocity vectors. Formore » the initial processing methods presented here, both techniques give out-of-plane positional accuracy of approximately 1–2 particle diameters. For a fixed image sensor, digital holography achieves higher effective in-plane spatial resolutions. However, collimated and coherent illumination makes holography susceptible to image distortion through index of refraction gradients, as demonstrated in the shotgun experiments. In contrast, plenoptic imaging allows for a simpler experimental configuration and, due to the use of diffuse, white-light illumination, plenoptic imaging is less susceptible to image distortion in the shotgun experiments.« less

Carbon loaded Teflon (CLT): a power density meter for biological experiments using millimeter waves.

PubMed

Allen, Stewart J; Ross, James A

2007-01-01

The standard technique for measurement of millimeter wave fields utilizes an open-ended waveguide attached to a HP power meter. The alignment of the waveguide with the propagation (K) vector is critical to making accurate measurements. Using this technique, it is difficult and time consuming to make a detailed map of average incident power density over areas of biological interest and the spatial resolution of this instrument does not allow accurate measurements in non-uniform fields. For biological experiments, it is important to know the center field average incident power density and the distribution over the exposed area. Two 4 ft x 4 ft x 1/32 inch sheets of carbon loaded Teflon (CLT) (one 15% carbon and one 25% carbon) were procured and a series of tests to determine the usefulness of CLT in defining fields in the millimeter wavelength range was initiated. Since the CLT was to be used both in the laboratory, where the environment was well controlled, and in the field, where the environment could not be controlled, tests were made to determine effects of change in environmental conditions on ability to use CLT as a millimeter wave dosimeter. The empirical results of this study indicate CLT to be an effective dosimeter for biological experiments both in the laboratory and in the field.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peralta, Pedro; Fortin, Elizabeth; Opie, Saul

Activities for this grant included: 1) Development of dynamic impact experiments to probe strength and phase transition influence on dynamic deformation, 2) development of modern strength and phase aware simulation capabilities, 3) and post-processing of experimental data with simulation and closed form analytical techniques. Two different dynamic experiments were developed to probe material strengths in solid metals (largely copper and iron in this effort). In the first experiment a flyer plate impacts a flat target with an opposite rippled surface that is partially supported by a weaker window material. Post mortem analysis of the target sample showed a strong andmore » repeatable residual plastic deformation dependence on grain orientation. Yield strengths for strain rates near 10 5 s -1 and plastic strains near ~50% were estimated to be around 180 to 240 MPa, varying in this range with grain orientation. Unfortunately dynamic real-time measurements were difficult with this setup due to diagnostic laser scattering; hence, an additional experimental setup was developed to complement these results. In the second set of experiments a rippled surface was ablated by a controlled laser pulsed, which launched a rippled shock front to an opposite initially flat diagnostic surface that was monitored in real-time with spatially resolved velocimetry techniques, e.g., line VISAR in addition to Transient Imaging Displacement Interferometry (TIDI) displacement measurements. This setup limited the displacements at the diagnostic surface to a reasonable level for TIDI measurements (~ less than one micrometer). These experiments coupled with analytical and numerical solutions provided evidence that viscous and elastic deviatoric strength affect shock front perturbation evolution in clearly different ways. Particularly, normalized shock front perturbation amplitudes evolve with viscosity (η) and perturbation wavelength (λ) as η/λ, such that increasing viscosity (or decreasing the initial wavelength) delays the perturbation decay. Conversely our experimental data, analysis and simulations show that for materials with elastic yield strength Y the normalized shock perturbation amplitude evolves with Yλ/A 0, which shows wavelength increases have the opposite effect as in viscous materials and perturbation decay is also dependent on initial amplitude A 0 (viscous materials are independent of this parameter). Materials where strength had clear strain rate dependence, e.g., such as a PTW material law, behaved similarly to materials with only an effective yield stress (elastic-perfectly plastic) in the shock front perturbation studies obeying a Y effλA 0 relationship where Y eff was a constant (near ~400 MPa for Cu for strain rates around 10 6 s -1). Magnitude changes in strain rate would increase Y eff as would be expected from the PTW behavior, but small perturbations (typical of regions behind the shock front) near a mean had little effect. Additional work based on simulations showed that phase transformation kinetics can affect the behavior of the perturbed shock front as well as the evolution of the RM-like instability that develops due to the imprint of the perturbed shock front on the initially flat surface as the shock breaks out.« less

Physiologic Cryoamputation in Managing Critically Ill Patients with Septic, Advanced Acute Limb Ischemia.

PubMed

Chen, Samuel L; Kuo, Isabella J; Kabutey, Nii-Kabu; Fujitani, Roy M

2017-07-01

Certain critically ill patients with advanced acute limb ischemia with a nonviable extremity may be unsuitable for transport to the operating room to undergo definitive amputation. In these unstable patients, rapid regional cryotherapy allows for prompt infectious source control and correction of hemodynamic and metabolic abnormalities, thereby lessening the risk associated with definitive surgical amputation. We describe our refined technique for lower extremity physiologic cryoamputation and review our institutional experience. After adequate analgesia is administered to the patient, a heating pad is secured circumferentially at the proximal amputation margin and the affected extremity is placed in a customized Styrofoam cooler. A circumferential seal is secured at the proximal chill zone without use of a tourniquet and dry ice is placed into the cooler to surround the entire affected leg. Delayed definitive lower extremity amputation is later performed when hemodynamic and metabolic derangements are corrected. We reviewed 5 patients who underwent lower extremity cryoamputation with this technique identified at our institution between 2005 and 2015. Age ranged from 31 to 79 years old. All presented with severe foot infection and septic shock requiring vasopressor support. All 5 patients stabilized hemodynamically following the initial cryoamputation and later underwent definitive lower extremity amputation, with a median time of 3 days following initial cryoamputation. Lower extremity physiologic cryoamputation is an effective, immediate bedside procedure that can provide local source control and the opportunity for correction of metabolic derangements in initially unstable patients to lessen the risk for definitive major lower extremity amputation. Refinement of the cryoamputation technique, as described in this report, allows for a predictable and reproducible physiologic amputation. Copyright © 2017 Elsevier Inc. All rights reserved.

Trends in Orbital Decompression Techniques of Surveyed American Society of Ophthalmic Plastic and Reconstructive Surgery Members.

PubMed

Reich, Shani S; Null, Robert C; Timoney, Peter J; Sokol, Jason A

To assess current members of the American Society of Ophthalmic Plastic and Reconstructive Surgery (ASOPRS) regarding preference in surgical techniques for orbital decompression in Graves' disease. A 10-question web-based, anonymous survey was distributed to oculoplastic surgeons utilizing the ASOPRS listserv. The questions addressed the number of years of experience performing orbital decompression surgery, preferred surgical techniques, and whether orbital decompression was performed in collaboration with an ENT surgeon. Ninety ASOPRS members participated in the study. Most that completed the survey have performed orbital decompression surgery for >15 years. The majority of responders preferred a combined approach of floor and medial wall decompression or balanced lateral and medial wall decompression; only a minority selected a technique limited to 1 wall. Those surgeons who perform fat decompression were more likely to operate in collaboration with ENT. Most surgeons rarely remove the orbital strut, citing risk of worsening diplopia or orbital dystopia except in cases of optic nerve compression or severe proptosis. The most common reason given for performing orbital decompression was exposure keratopathy. The majority of surgeons perform the surgery without ENT involvement, and number of years of experience did not correlate significantly with collaboration with ENT. The majority of surveyed ASOPRS surgeons prefer a combined wall approach over single wall approach to initial orbital decompression. Despite the technological advances made in the field of modern endoscopic surgery, no single approach has been adopted by the ASOPRS community as the gold standard.

[The role of antiarrhythmic surgery in 2004].

PubMed

Guiraudon, G M

2004-11-01

In 2004, surgery for cardiac arrhythmias addresses essentially atrial fibrillation. Surgery is only a rare alternative for other cardiac arrhythmias in center that still have the surgical skill. Surgery for atrial fibrillation has the definite advantage of concomitant exclusion of the left atrial appendage which is the predominant site of intra-atrial thrombi with the associated risk of severe thrombo-embolic events. Our experience with surgery for lone atrial fibrillation, using the Corridor III operation, shows that surgery is associated with high efficacy and long term control of arrhythmia when the surgical technique is well performed. Failures were associated with incomplete line of block or exclusion. This experience shows the necessity of postoperative EP testing. Initially performed using open heart technique, surger for atrial fibrillation is now performed using mini-invasive technique. Indications for surgery for lone atrial fibrillation will decreased while other strategies are developing. To remain competitive surgery must have high efficacy and use mini-invasive techniques. i.e.: closed off pump beating heart via port access. Surgery for atrial fibrillation concomitant with other cardiac surgical repairs yields remarkable results, without increased surgical risk. Their indications go beyond mitral valve pathology. Future developments imply the following conditions: atrial surgery must not increase morbidity, and its cost-effectiveness must be documented. Combined surgery must be testable and tested to gain valid pathophysiological data to improve surgical rationales. Its impact in terms of survival, prevention of thrombo-embolic events and quality of life will be documented by clinical trials.

An update on auricular reconstruction: three major auricular malformations of microtia, prominent ear and cryptotia.

PubMed

Park, Chul; Yoo, Yeon-Sik; Hong, Sung-Taek

2010-12-01

Microtia, prominent ear, and cryptotia are the most common types of auricular malformations. This review provides updated information on these types of reconstructions, in addition to recalling previously accepted surgical methods. Autogenous costal cartilage is still considered as an ideal material for framework fabrication in microtia reconstruction. Many surgeons have adopted the Nagata approach, the Brent approach, or variations of the two, in their work. With these employed techniques, auricles reconstructed by experienced surgeons have proven to be aesthetically promising. However, with regards to the harvesting of the costal cartilage, the underdevelopment of the chest wall donor site, alopecia of the scalp, and scarring of the postauricular-mastoid region are still considered problematic aspects of these approaches. Some articles have described attempts to solve these problems, whereas some experiments in cartilage production using tissue engineering techniques have shown promise in their initial stages of development.It is generally accepted that prominent ears should be corrected through a combination of sculpting and suture techniques, according to the individual shape and the quality of the ear prominence.Most of the cryptotia malformations show not only embedded upper auricles, but also associated adhesions of the upper auricular cartilage. Their correction should therefore resolve both deformities. A number of articles highlighting clinical experiences with auricular reconstructions for microtia, prominent ear, and cryptotia have been included in this review. We believe that the information synthesized here will become a basis for further development of auricular reconstruction techniques.

Percutaneous treatment of symptomatic non-parasitic hepatic cysts. Initial experience with single-session sclerotherapy with polidocanol.

PubMed

Spârchez, Zeno; Radu, Pompilia; Zaharie, Florin; Al Hajjar, Nadim; Sparchez, Mihaela

2014-09-01

Hepatic cysts have a prevalence of 2.5-7% and most of them are asymptomatic. However, large cysts may cause complaints; in such cases an appropriate treatment is necessary (open surgery, laparoscopic deroofing, removal of cystic fluid and injection of a sclerosing agent. The aim of this study was to assess the efficacy and safety of a single session technique with polidocanol in the therapy of symptomatic non parasitic hepatic cysts. MATERIAL AND METHODS. The study included 13 patients with symptomatic liver cysts (range 4-10 cm). All patients underwent percutaneous aspiration of the liver cyst under ultrasound guidance followed by instillation of polidocanol (3%, 4-10 ml). The patients were followed up at 1, 3 and 12 months. The disappearance of the cyst or reduction in volume more than 90% was considered successful. If the fluid was accumulated at 1month the procedure was repeated. If after the second injection the fluid accumulation was more than 50% of the initial volume the case was considered a failure and a laparoscopic deroofing was performed. The procedure was successful in 10 patients, 9 after the first instillation and one after the second (76.9%). The mean initial volume of cysts was 228 ml, and the mean reduction in volume at 1, 3 and 12 months was 80.2%, 91.9% and 96.7%. The cyst resolution was gradual with clinically significant cyst reduction achievement within 1 year after therapy. In 3 patients the fluid reaccumulated at the same volume despite 2 instillations. Those 3 cases the procedure was considered failure and the patients were sent to surgery. In 2 patients (one successfully treated and one with treatment failure) bleeding during the first puncture and aspiration appeared and the therapy was postponed for 1 month. There were no significant adverse effects, and all the patients had relief of symptoms after therapy. This initial experience with percutaneous aspiration and polidocanol sclerosis of hepatic cysts demonstrated that the technique is efficient and safe.

Pencil beam characteristics of the next-generation proton scanning gantry of PSI: design issues and initial commissioning results

NASA Astrophysics Data System (ADS)

Pedroni, E.; Meer, D.; Bula, C.; Safai, S.; Zenklusen, S.

2011-07-01

In this paper we report on the main design features, on the realization process and on selected first results of the initial commissioning of the new Gantry 2 of PSI for the delivery of proton therapy with new advanced pencil beam scanning techniques. We present briefly the characteristics of the new gantry system with main emphasis on the beam optics, on the characterization of the pencil beam used for scanning and on the performance of the scanning system. The idea is to give an overview of the major components of the whole system. The main long-term technical goal of the new equipment of Gantry 2 is to expand the use of pencil beam scanning to the whole spectrum of clinical indications including moving targets. We report here on the initial experience and problems encountered in the development of the system with selected preliminary results of the ongoing commissioning of Gantry 2.

Narrower grid structure of artificial reef enhances initial survival of in situ settled coral.

PubMed

Suzuki, Go; Kai, Sayaka; Yamashita, Hiroshi; Suzuki, Kiyoshi; Iehisa, Yukihiro; Hayashibara, Takeshi

2011-12-01

The initial factors that cause a decline in the survival of in situ settled corals remain poorly understood. In this study, we demonstrated through field experiments that the design of artificial grid plates may influence the initial survival of Acropora corals, with narrower grids being the most effective. In fact, grid plates with a 2.5-cm mesh presented the highest recorded survival rate (14%) at 6 months after settlement (representing approximately 50 corals per 0.25 m(2) of plate). This is the first study where such high survival rates, matching those of cultures under aquarium conditions, were obtained in the field without using additional protective measures, such as guard nets against fish grazing after seeding. Therefore, our results provide a foundation for establishing new and effective coral restoration techniques for larval seeding, in parallel to clarifying the details of the early life stages of reef-building corals. Copyright © 2011 Elsevier Ltd. All rights reserved.

Shock Initiation Characteristics of an Aluminized DNAN/RDX Melt-Cast Explosive

NASA Astrophysics Data System (ADS)

Cao, Tong-Tang; Zhou, Lin; Zhang, Xiang-Rong; Zhang, Wei; Miao, Fei-Chao

2017-10-01

Shock sensitivity is one of the key parameters for newly developed, 2,4-dinitroanisole (DNAN)-based, melt-cast explosives. For this paper, a series of shock initiation experiments were conducted using a one-dimensional Lagrangian system with a manganin piezoresistive pressure gauge technique to evaluate the shock sensitivity of an aluminized DNAN/cyclotrimethylenetrinitramine (RDX) melt-cast explosive. This study fully investigated the effects of particle size distributions in both RDX and aluminum, as well as the RDX's crystal quality on the shock sensitivity of the aluminized DNAN/RDX melt-cast explosive. Ultimately, the shock sensitivity of the aluminized DNAN/RDX melt-cast explosives increases when the particle size decreases in both RDX and aluminum. Additionally, shock sensitivity increases when the RDX's crystal quality decreases. In order to simulate these effects, an Ignition and Growth (I&G) reactive flow model was calibrated. This calibrated I&G model was able to predict the shock initiation characteristics of the aluminized DNAN/RDX melt-cast explosive.

Large deformation image classification using generalized locality-constrained linear coding.

PubMed

Zhang, Pei; Wee, Chong-Yaw; Niethammer, Marc; Shen, Dinggang; Yap, Pew-Thian

2013-01-01

Magnetic resonance (MR) imaging has been demonstrated to be very useful for clinical diagnosis of Alzheimer's disease (AD). A common approach to using MR images for AD detection is to spatially normalize the images by non-rigid image registration, and then perform statistical analysis on the resulting deformation fields. Due to the high nonlinearity of the deformation field, recent studies suggest to use initial momentum instead as it lies in a linear space and fully encodes the deformation field. In this paper we explore the use of initial momentum for image classification by focusing on the problem of AD detection. Experiments on the public ADNI dataset show that the initial momentum, together with a simple sparse coding technique-locality-constrained linear coding (LLC)--can achieve a classification accuracy that is comparable to or even better than the state of the art. We also show that the performance of LLC can be greatly improved by introducing proper weights to the codebook.

Use of the Ascent balloon for a 2-in-1 remodeling technique: feasibility and initial experience: case report.

PubMed

Clarençon, Frédéric; Pérot, Guillaume; Biondi, Alessandra; Di Maria, Federico; Szatmary, Zoltan; Chiras, Jacques; Sourour, Nader

2012-03-01

To present the feasibility of using the Ascent balloon, a new double-lumen remodeling balloon, for a new 2-in-1 technique allowing coiling through the lumen of the balloon without the use of an additional coiling microcatheter. Remodeling technique had enlarged the indications for endovascular treatment of intracranial aneurysm. Nevertheless, one of the limitations of this technique is that it requires using 2 devices in the same parent artery. A 55-year-old woman presented with a 7.7 × 4.5-mm incidental anterior communicating artery aneurysm. Only 1 A1 segment (left side) was patent on the cerebral angiogram. A 6F Fargo Max guiding catheter was positioned in the left petrous internal carotid artery. The Ascent balloon was placed in front of the neck of the aneurysm after navigation on a Traxcess 0.014-in guidewire. Coiling of the aneurysm sac was performed via 1 lumen of the device under iterative inflations of the balloon through the second lumen. This new 2-in-1 technique using a sole remodeling balloon without an additional coiling microcatheter is very promising, especially in cases of a small-caliber parent artery.

[NOTES ASSISTED ENDOLUMENAL RECTAL RESECTION AND SPECIMEN EXTRACTION WITHOUT RECTAL STUMP OPENING - OUR EXPERIENCE WITH THIS NOVEL TECHNIQUE IN A PORCINE MODEL].

PubMed

Kvasha, Anton; Rosenthal, Eyal; Khalifa, Muhammad; Waksman, Igor

2017-05-01

Laparoscopic surgery has long been used for colon and rectal resection, and the laparoscopic-assisted approach has prevailed in surgical practice. While this technique includes the fashioning of an intra-corporeal anastomosis, it still requires an abdominal incision for specimen extraction. Elimination of the abdominal incision and its potential complications has been the motivation for the development of natural orifice specimen extraction (NOSE) techniques. Many of these techniques make use of an open rectal stump, which poses as a potential for intra-abdominal contamination. Our group has recently described a novel, NOTES assisted, clean, endoluminal rectal resection utilizing transabdominal and transanal approaches. In this paper we report the combined experience of two study groups: an open approach to the abdominal cavity and a laparoscopic approach to the peritoneal cavity. Ten female pigs were used for this research; 5 in a group using an open approach and 5 using a laparoscopic approach for the abdominal part of the procedure. During the procedure, the rectum was mobilized. An end-to-end circular stapler was used to create a recto-rectal intussusception and pull-through (IPT). The specimen was resected and extracted by making a full thickness incision through 2 bowel walls. The stapler was applied, and a recto-rectal anastomosis created. This was allowed to retract into the abdomen. Peritoneal fluid was sampled for bacteria, the pigs were sacrificed immediately after the experiment and necropsy was performed. All 10 pigs underwent an endoluminal rectal resection utilizing the trans-anal IPT technique. The proximal and distal resection margins remained approximated over the shaft of the anvil after bowel resection in all 10 subjects. A 2- to 4-mm resection margin, distal to the ligatures was accomplished consistently in all 10 subjects. No aerobic or anaerobic bacterial growth was observed in any of the peritoneal fluid samples. Our research demonstrated the feasibility of the described technique in both open and laparoscopic approaches to a clean endoluminal bowel resection and trans-anal specimen extraction without rectal stump opening. The fact that no bacterial growth was found in any of the peritoneal samples supports the initial classification of this novel technique as clean, as opposed to clean contaminated, which classifies all other techniques in use to date.

Three-dimensional, thermo-mechanical and dynamical analogue experiments of subduction: first results

NASA Astrophysics Data System (ADS)

Boutelier, D.; Oncken, O.

2008-12-01

We present a new analogue modeling technique developed to investigate the mechanics of the subduction process and the build-up of subduction orogenies. The model consists of a tank filled with water representing the asthenosphere and two lithospheric plates made of temperature-sensitive hydrocarbon compositional systems. These materials possess elasto-plastic properties allowing the scaling of thermal and mechanical processes. A conductive thermal gradient is imposed in the lithosphere prior to deformation. The temperature of the asthenosphere and model surface are imposed and controlled with an electric heater, two infrared ceramic heat emitters, two thermocouples and a thermo-regulator. This system allows an unobstructed view of the model surface, which is monitored using a stereoscopic particle image technique. This monitoring technique provides a precise quantification of the horizontal deformation and variations of elevation in the three-dimensional model. Convergence is imposed with a piston moving at a constant rate or pushing at a constant stress. The velocity is scaled using the dimensionless ratio of thermal conduction over advection. The experiments are first produced at a constant rate and the stress in the horizontal direction of the convergence is recorded. Then the experiment is reproduced with a constant stress boundary condition where the stress value is set to the averaged value obtained in the previous experiment. Therefore, an initial velocity allowing proper scaling of heat exchanges is obtained, but deformation in the model and spatial variations of parameters such as density or friction coefficient can produce variations of plate convergence velocity. This in turn impacts the strength of the model lithosphere because it changes the model thermal structure. In the first presented experiments the model lithosphere is one layer and the plate boundary is linear. The effects of variations of the subducting plate thickness, density and the lubrication of the interface between the plates are investigated.

Comment on 'Detecting uniaxial single domain grains with a modified IRM technique' by R. Mitra, L. Tauxe and J. S. Gee

NASA Astrophysics Data System (ADS)

Fabian, K.

2012-10-01

In a recent article, Mitra et al. (2011) propose a modified IRM technique to identify the symmetry of magnetic anisotropy in single domain particle ensembles. They apply this technique to support an earlier suggestion that single domain grains in young mid-ocean ridge basalts (MORB) exhibit multiaxial anisotropy. Here it is shown that the design of their measurement is flawed, in that they do not take into account that the outcome essentially depends on the initial demagnetization state of the sample before the experiment, and on the coercivity distribution of the sample. Because all MORB specimens measured by Mitra et al. (2011) carried their original NRM, which closely resembles a thermally demagnetized state, their measurements first of all reflect the coercivity distributions and domain states of the samples, and contain little or no information about the symmetry of the magnetic anisotropy. All arguments previously put forward in favour of a dominant uniaxial anisotropy in MORB are therefore still valid.

Bulk heterojunction thin film formation by single and dual feed ultrasonic spray method for application in organic solar cells

NASA Astrophysics Data System (ADS)

Marathe, D. M.; Tarkas, H. S.; Mahajan, M. S.; Lonkar, G. S.; Tak, S. R.; Sali, J. V.

2016-09-01

We here present a way of preparing the polymer: fullerene BHJ using dual feed method which can lead to formation of pure phases. In this report, we present results of our initial experiments in this direction. The effect of process parameters on the thickness and surface roughness of the active layer has been discussed. The structural and optical properties have been studied using the optical microscope, UV—visible spectroscopy and photoluminescence spectroscopy. Significant PL quenching indicates efficient charge separation in the BHJ formed using this technique. We have also compared the BHJ thin films prepared with this dual feed ultrasonic technique with the single feed spray method. The BHJ formed using this technique has been used as an active layer in OSC. supported by the University Grants Commission, New Delhi, under Faculty Improvement Programme (No. 33-02/12(WRO) Dt.19.03.2013) and the Special Assistance Programme (530/2/DRS/2010(SAP-I)) Phase-II.

Rotation of EOFs by the Independent Component Analysis: Towards A Solution of the Mixing Problem in the Decomposition of Geophysical Time Series

NASA Technical Reports Server (NTRS)

Aires, Filipe; Rossow, William B.; Chedin, Alain; Hansen, James E. (Technical Monitor)

2001-01-01

The Independent Component Analysis is a recently developed technique for component extraction. This new method requires the statistical independence of the extracted components, a stronger constraint that uses higher-order statistics, instead of the classical decorrelation, a weaker constraint that uses only second-order statistics. This technique has been used recently for the analysis of geophysical time series with the goal of investigating the causes of variability in observed data (i.e. exploratory approach). We demonstrate with a data simulation experiment that, if initialized with a Principal Component Analysis, the Independent Component Analysis performs a rotation of the classical PCA (or EOF) solution. This rotation uses no localization criterion like other Rotation Techniques (RT), only the global generalization of decorrelation by statistical independence is used. This rotation of the PCA solution seems to be able to solve the tendency of PCA to mix several physical phenomena, even when the signal is just their linear sum.

Joint Optics Structures Experiment (JOSE)

NASA Technical Reports Server (NTRS)

Founds, David

1987-01-01

The objectives of the JOSE program is to develop, demonstrate, and evaluate active vibration suppression techniques for Directed Energy Weapons (DEW). DEW system performance is highly influenced by the line-of-sight (LOS) stability and in some cases by the wave front quality. The missions envisioned for DEW systems by the Strategic Defense Initiative require LOS stability and wave front quality to be significantly improved over any current demonstrated capability. The Active Control of Space Structures (ACOSS) program led to the development of a number of promising structural control techniques. DEW structures are vastly more complex than any structures controlled to date. They will be subject to disturbances with significantly higher magnitudes and wider bandwidths, while holding higher tolerances on allowable motions and deformations. Meeting the performance requirements of the JOSE program requires upgrading the ACOSS techniques to meet new more stringent requirements, the development of requisite sensors and acturators, improved control processors, highly accurate system identification methods, and the integration of hardware and methodologies into a successful demonstration.

Application Number 3: Using Tethers for Attitude Control

NASA Technical Reports Server (NTRS)

Muller, R. M.

1985-01-01

Past application of the gravity gradient concept to satellite attitude control produced attitude stabilities of from 1 to 10 degrees. The satellite members were rigigly interconnected and any motion in one part of the satellite would cause motion in all members. This experience has restricted gravity gradient stabilization to applications that need attitude stability no better than 1 degree. A gravity gradient technique that combines the flexible tether with an active control that will allow control stability much better than 1 degree is proposed. This could give gravity gradient stabilization much broader application. In fact, for a large structure like a space station, it may become the preferred method. Two possible ways of demonstrating the techniques using the Tethered Satellite System (TSS) tether to control the attitude of the shuttle are proposed. Then a possible space station tether configuration is shown that could be used to control the initial station. It is then shown how the technique can be extended to the control of space stations of virtually any size.

Effects of practice on tip-of-the-tongue states.

PubMed

Smith, S M; Balfour, S P; Brown, J M

1994-03-01

Tip-of-the-tongue (TOT) states were examined in relation to acquisition manipulations, using named imaginary animals (TOTimals) as targets. High levels of TOT states were found in three experiments. In the first experiment an increase in the duration of initial exposure to target material improved recall and recognition, and reduced the number of unrecalled items not in TOT states (NTOTs), but did not affect TOT levels. In Experiment 2 practice at writing target names, as compared with only reading them, improved recall performance and decreased TOT levels, but did not reduce NTOTs. Experiment 3 replicated the finding that writing during practice reduced TOT states, but did not reduce NTOTs, and also found that more frequent practice trials increased recall without affecting TOT levels. The results suggest that practice writing target names prevents TOT states by strengthening otherwise deficient phonological connections in memory, a deficiency that can cause TOT states when visual-to-lexical connections give only partial access to a target in memory. The results also demonstrate the usefulness of the TOTimal technique for testing effects of acquisition variables on TOT experiences.

Use of the Hugoniot elastic limit in laser shockwave experiments to relate velocity measurements

NASA Astrophysics Data System (ADS)

Smith, James A.; Lacy, Jeffrey M.; Lévesque, Daniel; Monchalin, Jean-Pierre; Lord, Martin

2016-02-01

The US National Nuclear Security Agency has a Global Threat Reduction Initiative (GTRI) with the goal of reducing the worldwide use of high-enriched uranium (HEU). A salient component of that initiative is the conversion of research reactors from HEU to low enriched uranium (LEU) fuels. An innovative fuel is being developed to replace HEU in high-power research reactors. The new LEU fuel is a monolithic fuel made from a U-Mo alloy foil encapsulated in Al-6061 cladding. In order to support the fuel qualification process, the Laser Shockwave Technique (LST) is being developed to characterize the clad-clad and fuel-clad interface strengths in fresh and irradiated fuel plates. This fuel-cladding interface qualification will ensure the survivability of the fuel plates in the harsh reactor environment even under abnormal operating conditions. One of the concerns of the project is the difficulty of calibrating and standardizing the laser shock technique. An analytical study under development and experimental testing supports the hypothesis that the Hugoniot Elastic Limit (HEL) in materials can be a robust and simple benchmark to compare stresses generated by different laser shock systems.

THz-driven zero-slippage IFEL scheme for phase space manipulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curry, E.; Fabbri, S.; Musumeci, P.

In this paper, we describe an inverse free electron laser (IFEL) interaction driven by a near single-cycle THz pulse that is group velocity-matched to an electron bunch inside a waveguide, allowing for a sustained interaction in a magnetic undulator. We discuss the application of this guided-THz IFEL technique for compression of a relativistic electron bunch and synchronization with the external laser pulse used to generate the THz pulse via optical rectification, as well as a laser-driven THz streaking diagnostic with the potential for femtosecond scale temporal resolution. Initial measurements of the THz waveform via an electro-optic sampling based technique confirm the predicted reduction of the group velocity, using a curved parallel plate waveguide, as a function of the varying aperture size of the guide. We also present the design of a proof-of-principle experiment based on the bunch parameters available at the UCLA PEGASUS laboratory. With amore » $$10\\,\\mathrm{MV}\\,{{\\rm{m}}}^{-1}$$ THz peak field, our simulation model predicts compression of a $$6\\,\\mathrm{MeV}$$ $$100\\,\\mathrm{fs}$$ electron beam by nearly an order of magnitude and a significant reduction of its initial timing jitter.« less

THz-driven zero-slippage IFEL scheme for phase space manipulation

DOE PAGES

Curry, E.; Fabbri, S.; Musumeci, P.; ...

2016-11-24

In this paper, we describe an inverse free electron laser (IFEL) interaction driven by a near single-cycle THz pulse that is group velocity-matched to an electron bunch inside a waveguide, allowing for a sustained interaction in a magnetic undulator. We discuss the application of this guided-THz IFEL technique for compression of a relativistic electron bunch and synchronization with the external laser pulse used to generate the THz pulse via optical rectification, as well as a laser-driven THz streaking diagnostic with the potential for femtosecond scale temporal resolution. Initial measurements of the THz waveform via an electro-optic sampling based technique confirm the predicted reduction of the group velocity, using a curved parallel plate waveguide, as a function of the varying aperture size of the guide. We also present the design of a proof-of-principle experiment based on the bunch parameters available at the UCLA PEGASUS laboratory. With amore » $$10\\,\\mathrm{MV}\\,{{\\rm{m}}}^{-1}$$ THz peak field, our simulation model predicts compression of a $$6\\,\\mathrm{MeV}$$ $$100\\,\\mathrm{fs}$$ electron beam by nearly an order of magnitude and a significant reduction of its initial timing jitter.« less

Remediation of 137Cs contaminated concrete using electrokinetic phenomena and ionic salt washes in nuclear energy contexts.

PubMed

Parker, Andrew J; Joyce, Malcolm J; Boxall, Colin

2017-10-15

This work describes the first known the use of electrokinetic treatments and ionic salt washes to remediate concrete contaminated with 137 Cs. A series of experiments were performed on concrete samples, contaminated with K + and 137 Cs, using a bespoke migration cell and an applied electric field (60V potential gradient and current limit of 35mA). Additionally, two samples were treated with an ionic salt wash (≤400molm -3 of KCl) alongside the electrokinetic treatment. The results show that the combined treatment produces removal efficiencies three times higher (>60%) than the electrokinetic treatment alone and that the decontamination efficiency appears to be proportional to the initial degree of contamination. Furthermore, the decontamination efficiencies are equivalent to previous electrokinetic studies that utilised hazardous chemical enhancement agents demonstrating the potential of the technique for use on nuclear licensed site. The results highlight the relationship between the initial contamination concentration within the concrete and achievable removal efficiency of electrokinetic treatment and other treatments. This information would be useful when selecting the most appropriate decontamination techniques for particular contamination scenarios. Copyright © 2017 Elsevier B.V. All rights reserved.

In-hospital cost comparison between the standard lateral and supercapsular percutaneously-assisted total hip surgical techniques for total hip replacement.

PubMed

Gofton, Wade; Fitch, David A

2016-03-01

The purpose of this study was to compare the in-hospital costs associated with the tissue-sparing supercapsular percutaneously-assisted total hip (SuperPath) and traditional Lateral surgical techniques for total hip replacement (THR). Between April 2013 and January 2014, in-hospital costs were reviewed for all THRs performed using the SuperPath technique by a single surgeon and all THRs performed using the Lateral technique by another surgeon at the same institution. Overall, costs were 28.4% higher in the Lateral group. This was largely attributable to increased costs associated with transfusion (+92.5%), patient rooms (+60.4%), patient food (+62.8%), narcotics (+42.5%), physical therapy (+52.5%), occupational therapy (+88.6%), and social work (+92.9%). The only costs noticeably increased for SuperPath were for imaging (+105.9%), and this was because the SuperPath surgeon performed intraoperative radiographs on all patients while the Lateral surgeon did not. The use of the SuperPath technique resulted in in-hospital cost reductions of over 28%, suggesting that this tissue-sparing surgical technique can be cost-effective primarily by facilitating early mobilisation and patient discharge even during a surgeon's initial experience with the approach.

Propagation and deposition of non-circular finite release particle-laden currents

NASA Astrophysics Data System (ADS)

Zgheib, Nadim; Bonometti, Thomas; Balachandar, S.

2015-08-01

The dynamics of non-axisymmetric turbidity currents is considered here for a range of Reynolds numbers of O (104) when based on the initial height of the release. The study comprises a series of experiments and highly resolved simulations for which a finite volume of particle-laden solution is released into fresh water. A mixture of water and polystyrene particles of mean diameter d ˜ p = 300 μ m and mixture density ρ ˜ c = 1012 kg / m 3 is initially confined in a hollow cylinder at the centre of a large tank filled with fresh water. Cylinders with two different cross-sectional shapes, but equal cross-sectional areas, are examined: a circle and a rounded rectangle in which the sharp corners are smoothened. The time evolution of the front is recorded as well as the spatial distribution of the thickness of the final deposit via the use of a laser triangulation technique. The dynamics of the front and final deposits are significantly influenced by the initial geometry, displaying substantial azimuthal variation especially for the rectangular case where the current extends farther and deposits more particles along the initial minor axis of the rectangular cross section. Several parameters are varied to assess the dependence on the settling velocity, initial height aspect ratio, and volume fraction. Even though resuspension is not taken into account in our simulations, good agreement with experiments indicates that it does not play an important role in the front dynamics, in terms of velocity and extent of the current. However, wall shear stress measurements show that incipient motion of particles and particle transport along the bed are likely to occur in the body of the current and should be accounted to properly capture the final deposition profile of particles.

Generation of 360 ps laser pulse with 3 J energy by stimulated Brillouin scattering with a nonfocusing scheme.

PubMed

Zhu, Xuehua; Wang, Yulei; Lu, Zhiwei; Zhang, Hengkang

2015-09-07

A new technique for generating high energy sub-400 picosecond laser pulses is presented in this paper. The temporally super-Gaussian-shaped laser pulses are used as light source. When the forward pump is reflected by the rear window of SBS cell, the frequency component that fulfills Brillouin frequency shift in its sideband spectrum works as a seed and excites SBS, which results in efficient compression of the incident pump pulse. First the pulse compression characteristics of 20th-order super-Gaussian temporally shaped pulses with 5 ns duration are analyzed theoretically. Then experiment is carried out with a narrow-band high power Nd:glass laser system at the double-frequency and wavelength of 527 nm which delivers 5 ns super-Gaussian temporally shaped pulses with single pulse energy over 10 J. FC-40 is used as the active SBS medium for its brief phonon lifetime and high power capacity. In the experiment, the results agree well with the numerical calculations. With pump energy of 5.36J, the compression of pulse duration from 5 ns to 360 ps is obtained. The output energy is 3.02 J and the peak-power is magnified 8.3 times. Moreover, the compressed pulse shows a high stability because it is initiated by the feedback of rear window rather than the thermal noise distributing inside the medium. This technique of generating high energy hundred picosecond laser pulses has simple structure and is easy to operate, and it also can be scaled to higher energy pulse compression in the future. Meanwhile, it should also be taken into consideration that in such a nonfocusing scheme, the noise-initiated SBS would increase the distortion on the wavefront of Stokes beam to some extent, and the pump energy should be controlled below the threshold of noise-initiated SBS.

Synchro-ballistic recording of detonation phenomena

NASA Astrophysics Data System (ADS)

Critchfield, Robert R.; Asay, Blaine W.; Bdzil, John B.; Davis, William C.; Ferm, Eric N.; Idar, Deanne J.

1997-12-01

Synchro-ballistic use of rotating-mirror streak cameras allows for detailed recording of high-speed events of known velocity and direction. After an introduction to the synchro-ballistic technique, this paper details two diverse applications of the technique as applied in the field of high-explosives research. In the first series of experiments detonation-front shape is recorded as the arriving detonation shock wave tilts an obliquely mounted mirror, causing reflected light to be deflected from the imaging lens. These tests were conducted for the purpose of calibrating and confirming the asymptotic detonation shock dynamics (DSD) theory of Bdzil and Stewart. The phase velocities of the events range from ten to thirty millimeters per microsecond. Optical magnification is set for optimal use of the film's spatial dimension and the phase velocity is adjusted to provide synchronization at the camera's maximum writing speed. Initial calibration of the technique is undertaken using a cylindrical HE geometry over a range of charge diameters and of sufficient length-to- diameter ratio to insure a stable detonation wave. The final experiment utilizes an arc-shaped explosive charge, resulting in an asymmetric denotation-front record. The second series of experiments consists of photographing a shaped-charge jet having a velocity range of two to nine millimeters per microsecond. To accommodate the range of velocities it is necessary to fire several tests, each synchronized to a different section of the jet. The experimental apparatus consists of a vacuum chamber to preclude atmospheric ablation of the jet tip with shocked-argon back lighting to produce a shadow-graph image.

Synchro-ballistic recording of detonation phenomena

DOE Office of Scientific and Technical Information (OSTI.GOV)

Critchfield, R.R.; Asay, B.W.; Bdzil, J.B.

1997-09-01

Synchro-ballistic use of rotating-mirror streak cameras allows for detailed recording of high-speed events of known velocity and direction. After an introduction to the synchro-ballistic technique, this paper details two diverse applications of the technique as applied in the field of high-explosives research. In the first series of experiments detonation-front shape is recorded as the arriving detonation shock wave tilts an obliquely mounted mirror, causing reflected light to be deflected from the imaging lens. These tests were conducted for the purpose of calibrating and confirming the asymptotic Detonation Shock Dynamics (DSD) theory of Bdzil and Stewart. The phase velocities of themore » events range from ten to thirty millimeters per microsecond. Optical magnification is set for optimal use of the film`s spatial dimension and the phase velocity is adjusted to provide synchronization at the camera`s maximum writing speed. Initial calibration of the technique is undertaken using a cylindrical HE geometry over a range of charge diameters and of sufficient length-to-diameter ratio to insure a stable detonation wave. The final experiment utilizes an arc-shaped explosive charge, resulting in an asymmetric detonation-front record. The second series of experiments consists of photographing a shaped-charge jet having a velocity range of two to nine millimeters per microsecond. To accommodate the range of velocities it is necessary to fire several tests, each synchronized to a different section of the jet. The experimental apparatus consists of a vacuum chamber to preclude atmospheric ablation of the jet tip with shocked-argon back lighting to produce a shadow-graph image.« less

Advantages and Disadvantages of the Amplatzer Vascular Plug IV in Visceral Embolization: Report of 50 Placements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pech, Maciej, E-mail: maciej.pech@med.ovgu.de; Mohnike, Konrad; Wieners, Gero

2011-10-15

Purpose: We describe our initial clinical experience in artificial embolization with the Amplatzer Vascular Plug IV (VP IV), a further development of the Vascular Plug family already in routine use. Methods: Results from 50 embolization procedures conducted with the VP IV in 44 patients are summarized. Results: All 50 embolizations were successful, although two required the technique to be modified because of problems with jamming of the screw thread and thus with disconnection of the plug. This was associated with large branching angles. Conclusions: With experience, the VP IV can be used safely and effectively, and it expands the spectrummore » of possible embolizations in interventional radiology. Its greatest disadvantage is its relatively poor positional controllability.« less

Space plasma research

NASA Technical Reports Server (NTRS)

Comfort, R. H.; Horwitz, J. L.

1986-01-01

Temperature and density analysis in the Automated Analysis Program (for the global empirical model) were modified to use flow velocities produced by the flow velocity analysis. Revisions were started to construct an interactive version of the technique for temperature and density analysis used in the automated analysis program. A sutdy of ion and electron heating at high altitudes in the outer plasmasphere was initiated. Also the analysis of the electron gun experiments on SCATHA were extended to include eclipse operations in order to test a hypothesis that there are interactions between the 50 to 100 eV beam and spacecraft generated photoelectrons. The MASSCOMP software to be used in taking and displaying data in the two-ion plasma experiment was tested and is now working satisfactorily. Papers published during the report period are listed.

Psychophysically based model of surface gloss perception

NASA Astrophysics Data System (ADS)

Ferwerda, James A.; Pellacini, Fabio; Greenberg, Donald P.

2001-06-01

In this paper we introduce a new model of surface appearance that is based on quantitative studies of gloss perception. We use image synthesis techniques to conduct experiments that explore the relationships between the physical dimensions of glossy reflectance and the perceptual dimensions of glossy appearance. The product of these experiments is a psychophysically-based model of surface gloss, with dimensions that are both physically and perceptually meaningful and scales that reflect our sensitivity to gloss variations. We demonstrate that the model can be used to describe and control the appearance of glossy surfaces in synthesis images, allowing prediction of gloss matches and quantification of gloss differences. This work represents some initial steps toward developing psychophyscial models of the goniometric aspects of surface appearance to complement widely-used colorimetric models.

Modular space station detailed preliminary design. Volume 1: Sections 1 through 4.4

NASA Technical Reports Server (NTRS)

1971-01-01

Detailed configuration and subsystems preliminary design data are presented for the modular space station concept. Each module comprising the initial space station is described in terms of its external and internal configuration, its functional responsibilities to the initial cluster, and its orbital build up sequence. Descriptions of the subsequent build up to the growth space station are also presented. Analytical and design techniques, tradeoff considerations, and depth of design detail are discussed for each subsystem. The subsystems include the following: structural/mechanical; crew habitability and protection; experiment support; electrical power; environmental control/life support; guidance, navigation, and control; propulsion; communications; data management; and onboard checkout subsystems. The interfaces between the station and other major elements of the program are summarized. The rational for a zero-gravity station, in lieu of one with artificial-gravity capability, is also summarized.

Fire-protection research for energy technology: Fy 80 year end report

NASA Astrophysics Data System (ADS)

Hasegawa, H. K.; Alvares, N. J.; Lipska, A. E.; Ford, H.; Priante, S.; Beason, D. G.

1981-05-01

This continuing research program was initiated in order to advance fire protection strategies for Fusion Energy Experiments (FEE). The program expanded to encompass other forms of energy research. Accomplishments for fiscal year 1980 were: finalization of the fault-free analysis of the Shiva fire management system; development of a second-generation, fire-growth analysis using an alternate model and new LLNL combustion dynamics data; improvements of techniques for chemical smoke aerosol analysis; development and test of a simple method to assess the corrosive potential of smoke aerosols; development of an initial aerosol dilution system; completion of primary small-scale tests for measurements of the dynamics of cable fires; finalization of primary survey format for non-LLNL energy technology facilities; and studies of fire dynamics and aerosol production from electrical insulation and computer tape cassettes.

Flight data identification of six degree-of-freedom stability and control derivatives of a large crane type helicopter

NASA Technical Reports Server (NTRS)

Tomaine, R. L.

1976-01-01

Flight test data from a large 'crane' type helicopter were collected and processed for the purpose of identifying vehicle rigid body stability and control derivatives. The process consisted of using digital and Kalman filtering techniques for state estimation and Extended Kalman filtering for parameter identification, utilizing a least squares algorithm for initial derivative and variance estimates. Data were processed for indicated airspeeds from 0 m/sec to 152 m/sec. Pulse, doublet and step control inputs were investigated. Digital filter frequency did not have a major effect on the identification process, while the initial derivative estimates and the estimated variances had an appreciable effect on many derivative estimates. The major derivatives identified agreed fairly well with analytical predictions and engineering experience. Doublet control inputs provided better results than pulse or step inputs.

The Tool for Designing Engineering Systems Using a New Optimization Method Based on a Stochastic Process

NASA Astrophysics Data System (ADS)

Yoshida, Hiroaki; Yamaguchi, Katsuhito; Ishikawa, Yoshio

The conventional optimization methods were based on a deterministic approach, since their purpose is to find out an exact solution. However, these methods have initial condition dependence and risk of falling into local solution. In this paper, we propose a new optimization method based on a concept of path integral method used in quantum mechanics. The method obtains a solutions as an expected value (stochastic average) using a stochastic process. The advantages of this method are not to be affected by initial conditions and not to need techniques based on experiences. We applied the new optimization method to a design of the hang glider. In this problem, not only the hang glider design but also its flight trajectory were optimized. The numerical calculation results showed that the method has a sufficient performance.

Evaluation of the metabolic fate of munitions material (TNT & RDX) in plant systems. Initial assessment of plant DNA mutation spectra as a biomarker

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leung, F.; Cataldo, D.A.; Fellows, R.J.

1995-09-01

Munitions material can enter the environment as a result of manufacturing activities and field usage. Predictor methodologies, or biomarkers would enhance evaluation of environmental impacts. The goal of this exploratory study deoxyribonucleic acid (DNA) mutation frequency as a biomarker for munitions exposure. The approach e resolution of an effective repetitive sequence probe for the identification of characteristic mutations, and (2) the development of a testing media [a clonal cell line of carrot (Daucus carota) spension cells]. Commercially available probes demonstrated marginal resolution therefore a low-C{sub o}t library was then constructed. Three colonies from the low-C{sub o}t DNA library were screenedmore » and the DNA isolates sequenced. A suspension culture of carrot (Daucus carota) was developed. A mutation spectra experiment was initiated at a 10-mg TNT/L exposure concentration with the attempt to clone over 1500 single TNT-exposed cells. Over the following six months greater than 98% of the initially isolated cells were unable to survive and produce micro calluses. The remaining calli were too few to be statistically significant and the experiment was terminated. The biomarker concept itself remains to be disproved, but the need for large numbers of uniform clones to differentiate true mutations suggest that more direct techniques using whole tissues need to be developed.« less

Determination of oxidant exposure during ozonation of secondary effluent to predict contaminant removal.

PubMed

Zucker, Ines; Avisar, Dror; Mamane, Hadas; Jekel, Martin; Hübner, Uwe

2016-09-01

The use of kinetic models to predict oxidation performance in wastewater is limited due to fast ozone depletion during the first milliseconds of the reaction. This paper introduces the Quench Flow Module (QFM), a bench-scale experimental technique developed to measure the first 5-500 milliseconds of ozone depletion for accurate determination of ozone exposure in wastewater-ozonation processes. Calculated ozone exposure in QFM experiments was up to 24% lower than in standard batch experiments, strongly depending on the initial sampling point for measurement in batch experiments. However, oxidation rates of slowly- and moderately-reacting trace organic compounds (TrOCs) were accurately predicted from batch experiments based on integration of ozone depletion and removal of an ozone-resistant probe compound to calculate oxidant exposures. An alternative concept, where ozone and hydroxyl radical exposures are back-calculated from the removal of two probe compounds, was tested as well. Although the QFM was suggested to be an efficient mixing reactor, ozone exposure ranged over three orders of magnitude when different probe compounds reacting moderately with ozone were used for the calculation. These effects were beyond uncertainty ranges for apparent second order rate constants and consistently observed with different ozone-injection techniques, i.e. QFM, batch experiments, bubble columns and venturi injection. This indicates that previously suggested mixing effects are not responsible for the difference and other still unknown factors might be relevant. Results furthermore suggest that ozone exposure calculations from the relative residual concentration of a probe compound are not a promising option for evaluation of ozonation of secondary effluents. Copyright © 2016 Elsevier Ltd. All rights reserved.

Use of a Re-entry Device in Left Subclavian Occlusion: Case Series.

PubMed

Thomas, Wiliam Rhodri; Chick, Christopher; Goyal, Nimit

2018-01-01

To describe the use of a re-entry catheter in the endovascular treatment of left subclavian stenosis. We present three patients where initial attempts at re-vascularisation using standard techniques were unsuccessful. An OUTBACK catheter was employed to facilitate re-entry in these patients. True lumen re-entry was achieved in all patients, leading to successful treatment of all stenoses. There was a lack of filling of the left vertebral artery post-angioplasty in one patient; this was not clinically significant. The case series presented is encouraging for the use of a re-entry catheter in the treatment of subclavian occlusion. In our limited experience this has proved to be a safe technique for use in patients who fail re-vascularisation by standard methods; a larger study is required to confirm this.

Single line-of-sight dual energy backlighter for mix width experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, K. L., E-mail: baker7@llnl.gov; Glendinning, S. G.; Martinez, D.

2014-11-15

We present a diagnostic technique used to spatially multiplex two x-ray radiographs of an object onto a detector along a single line-of-sight. This technique uses a thin, <2 μm, cosputtered backlighter target to simultaneously produce both Ni and Zn He{sub α} emission. A Ni picket fence filter, 500 μm wide bars and troughs, is then placed in front of the detector to pass only the Ni He{sub α} emission in the bar region and both energies in the trough region thereby spatially multiplexing the two radiographs on a single image. Initial experimental results testing the backlighter spectrum are presented alongmore » with simulated images showing the calculated radiographic images though the nickel picket fence filter which are used to measure the mix width in an accelerated nickel foam.« less

A Preliminary Comparison of Three Dimensional Particle Tracking and Sizing using Plenoptic Imaging and Digital In-line Holography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guildenbecher, Daniel Robert; Munz, Elise Dahnke; Farias, Paul Abraham

2015-12-01

Digital in-line holography and plenoptic photography are two techniques for single-shot, volumetric measurement of 3D particle fields. Here we present a preliminary comparison of the two methods by applying plenoptic imaging to experimental configurations that have been previously investigated with digital in-line holography. These experiments include the tracking of secondary droplets from the impact of a water drop on a thin film of water and tracking of pellets from a shotgun. Both plenoptic imaging and digital in-line holography successfully quantify the 3D nature of these particle fields. This includes measurement of the 3D particle position, individual particle sizes, and three-componentmore » velocity vectors. For the initial processing methods presented here, both techniques give out-of-plane positional accuracy of approximately 1-2 particle diameters. For a fixed image sensor, digital holography achieves higher effective in-plane spatial resolutions. However, collimated and coherent illumination makes holography susceptible to image distortion through index of refraction gradients, as demonstrated in the shotgun experiments. On the other hand, plenotpic imaging allows for a simpler experimental configuration. Furthermore, due to the use of diffuse, white-light illumination, plenoptic imaging is less susceptible to image distortion in the shotgun experiments. Additional work is needed to better quantify sources of uncertainty, particularly in the plenoptic experiments, as well as develop data processing methodologies optimized for the plenoptic measurement.« less

A Preliminary Comparison of Three Dimensional Particle Tracking and Sizing using Plenoptic Imaging and Digital In-line Holography [PowerPoint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guildenbecher, Daniel Robert; Munz, Elise Dahnke; Farias, Paul Abraham

2015-12-01

Digital in-line holography and plenoptic photography are two techniques for single-shot, volumetric measurement of 3D particle fields. Here we present a preliminary comparison of the two methods by applying plenoptic imaging to experimental configurations that have been previously investigated with digital in-line holography. These experiments include the tracking of secondary droplets from the impact of a water drop on a thin film of water and tracking of pellets from a shotgun. Both plenoptic imaging and digital in-line holography successfully quantify the 3D nature of these particle fields. This includes measurement of the 3D particle position, individual particle sizes, and three-componentmore » velocity vectors. For the initial processing methods presented here, both techniques give out-of-plane positional accuracy of approximately 1-2 particle diameters. For a fixed image sensor, digital holography achieves higher effective in-plane spatial resolutions. However, collimated and coherent illumination makes holography susceptible to image distortion through index of refraction gradients, as demonstrated in the shotgun experiments. On the other hand, plenotpic imaging allows for a simpler experimental configuration. Furthermore, due to the use of diffuse, white-light illumination, plenoptic imaging is less susceptible to image distortion in the shotgun experiments. Additional work is needed to better quantify sources of uncertainty, particularly in the plenoptic experiments, as well as develop data processing methodologies optimized for the plenoptic measurement.« less

Inverse Regional Modeling with Adjoint-Free Technique

NASA Astrophysics Data System (ADS)

Yaremchuk, M.; Martin, P.; Panteleev, G.; Beattie, C.

2016-02-01

The ongoing parallelization trend in computer technologies facilitates the use ensemble methods in geophysical data assimilation. Of particular interest are ensemble techniques which do not require the development of tangent linear numerical models and their adjoints for optimization. These ``adjoint-free'' methods minimize the cost function within the sequence of subspaces spanned by a carefully chosen sets perturbations of the control variables. In this presentation, an adjoint-free variational technique (a4dVar) is demonstrated in an application estimating initial conditions of two numerical models: the Navy Coastal Ocean Model (NCOM), and the surface wave model (WAM). With the NCOM, performance of both adjoint and adjoint-free 4dVar data assimilation techniques is compared in application to the hydrographic surveys and velocity observations collected in the Adriatic Sea in 2006. Numerical experiments have shown that a4dVar is capable of providing forecast skill similar to that of conventional 4dVar at comparable computational expense while being less susceptible to excitation of ageostrophic modes that are not supported by observations. Adjoint-free technique constrained by the WAM model is tested in a series of data assimilation experiments with synthetic observations in the southern Chukchi Sea. The types of considered observations are directional spectra estimated from point measurements by stationary buoys, significant wave height (SWH) observations by coastal high-frequency radars and along-track SWH observations by satellite altimeters. The a4dVar forecast skill is shown to be 30-40% better than the skill of the sequential assimilaiton method based on optimal interpolation which is currently used in operations. Prospects of further development of the a4dVar methods in regional applications are discussed.

76 FR 66698 - Postsecondary Educational Institutions Invited To Participate in Experiments Under the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-27

... Experiments Under the Experimental Sites Initiative AGENCY: Office of Postsecondary Education, Department of... institutions to participate in experiments under the Experimental Sites Initiative. SUMMARY: The Secretary... participate in one or more new experiments under the Experimental Sites Initiative (ESI), as authorized by...

Treatment of cerebral vasospasm with self-expandable retrievable stents: proof of concept.

PubMed

Bhogal, Pervinder; Loh, Yince; Brouwer, Patrick; Andersson, Tommy; Söderman, Michael

2017-01-01

To report our preliminary experience with the use of stent retrievers to cause vasodilation in patients with delayed cerebral vasospasm secondary to subarachnoid hemorrhage. Four patients from two different high volume neurointerventional centers developed cerebral vasospasm following subarachnoid hemorrhage. In addition to standard techniques for the treatment of cerebral vasospasm, we used commercially available stent retrievers (Solitaire and Capture stent retrievers) to treat the vasospastic segment including M2, M1, A2, and A1. We evaluated the safety of this technique, degree of vasodilation, and longevity of the effect. Stent retrievers can be used to safely achieve cerebral vasodilation in the setting of delayed cerebral vasospasm. The effect is long-lasting (>24 hours) and, in our initial experience, carries a low morbidity. We have not experienced any complications using this technique although we have noted that the radial force was not sufficient to cause vasodilation in some instances. The vasospasm did not return in the vessel segments treated with stent angioplasty in any of these cases. In two of our cases stent angioplasty resulted in the reversal of focal neurological symptoms. Stent retrievers can provide long-lasting cerebral vasodilation in patients with delayed cerebral vasospasm. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Comparison of digital scanning and polyvinyl siloxane impression techniques by dental students: instructional efficiency and attitudes towards technology.

PubMed

Marti, A M; Harris, B T; Metz, M J; Morton, D; Scarfe, W C; Metz, C J; Lin, W-S

2017-08-01

With increasing use of digital scanning with restorative procedures in the dental office, it becomes necessary that educational institutions adopt instructional methodology for introducing this technology together with conventional impression techniques. To compare the time differences between instructing dental students on digital scanning (DS) (LAVA C.O.S. digital impression system) and a conventional impression technique (CI) (polyvinyl siloxane), and to compare students' attitudes and beliefs towards both techniques. Volunteer sophomore dental students (n = 25) with no prior experience in clinical impressions were recruited and IRB consent obtained. Participants responded to a pre-and post-exposure questionnaire. Participants were instructed on the use of both DS and CI for a single tooth full coverage crown restoration using a consecutive sequence of video lecture, investigator-led demonstration and independent impression exercise. The time necessary for each step (minutes) was recorded. Statistical significance was calculated using dependent t-tests (time measurements) and 2-sample Mann-Whitney (questionnaire responses). The time spent teaching students was greater for DS than CI for video lecture (15.95 and 10.07 min, P = 0.0000), demonstration time (9.06 and 4.70 min, P = 0.0000) and impression time (18.17 and 8.59 min, P = 0.0000). Prior to the instruction and practice, students considered themselves more familiar with CI (3.96) than DS (1.96) (P = 0.0000). After the instruction and practice, participants reported CI technique proved significantly easier than expected (pre-instruction: 3.52 and post-instruction: 4.08, P = 0.002). However, overall participants' perception of ease of use for DS was not influenced by this instruction and practice experience (pre-instruction: 3.84 and post-instruction: 3.56, P = 0.106). Despite the results, 96% of participants expressed an expectation that DS will become their predominant impression technique during their careers. Dental students with no clinical experience have high expectations for digital scanning, and despite their initial difficulty, expect it to become their primary impression technique during their professional futures. The instructional time necessary for introducing DS into the curriculum is significantly greater than CI in both classroom (lecture) and clinical simulation settings (investigator-led demonstration). © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

In Situ Investigation of Electrochemically Mediated Surface-Initiated Atom Transfer Radical Polymerization by Electrochemical Surface Plasmon Resonance.

PubMed

Chen, Daqun; Hu, Weihua

2017-04-18

Electrochemically mediated atom transfer radical polymerization (eATRP) initiates/controls the controlled/living ATRP chain propagation process by electrochemically generating (regenerating) the activator (lower-oxidation-state metal complex) from deactivator (higher-oxidation-state metal complex). Despite successful demonstrations in both of the homogeneous polymerization and heterogeneous systems (namely, surface-initiated ATRP, SI-ATRP), the eATRP process itself has never been in situ investigated, and important information regarding this process remains unrevealed. In this work, we report the first investigation of the electrochemically mediated SI-ATRP (eSI-ATRP) by rationally combining the electrochemical technique with real-time surface plasmon resonance (SPR). In the experiment, the potential of a SPR gold chip modified by the self-assembled monolayer of the ATRP initiator was controlled to electrochemically reduce the deactivator to activator to initiate the SI-ATRP, and the whole process was simultaneously monitored by SPR with a high time resolution of 0.1 s. It is found that it is feasible to electrochemically trigger/control the SI-ATRP and the polymerization rate is correlated to the potential applied to the gold chip. This work reveals important kinetic information for eSI-ATRP and offers a powerful platform for in situ investigation of such complicated processes.

A formal concept analysis approach to consensus clustering of multi-experiment expression data

PubMed Central

2014-01-01

Background Presently, with the increasing number and complexity of available gene expression datasets, the combination of data from multiple microarray studies addressing a similar biological question is gaining importance. The analysis and integration of multiple datasets are expected to yield more reliable and robust results since they are based on a larger number of samples and the effects of the individual study-specific biases are diminished. This is supported by recent studies suggesting that important biological signals are often preserved or enhanced by multiple experiments. An approach to combining data from different experiments is the aggregation of their clusterings into a consensus or representative clustering solution which increases the confidence in the common features of all the datasets and reveals the important differences among them. Results We propose a novel generic consensus clustering technique that applies Formal Concept Analysis (FCA) approach for the consolidation and analysis of clustering solutions derived from several microarray datasets. These datasets are initially divided into groups of related experiments with respect to a predefined criterion. Subsequently, a consensus clustering algorithm is applied to each group resulting in a clustering solution per group. These solutions are pooled together and further analysed by employing FCA which allows extracting valuable insights from the data and generating a gene partition over all the experiments. In order to validate the FCA-enhanced approach two consensus clustering algorithms are adapted to incorporate the FCA analysis. Their performance is evaluated on gene expression data from multi-experiment study examining the global cell-cycle control of fission yeast. The FCA results derived from both methods demonstrate that, although both algorithms optimize different clustering characteristics, FCA is able to overcome and diminish these differences and preserve some relevant biological signals. Conclusions The proposed FCA-enhanced consensus clustering technique is a general approach to the combination of clustering algorithms with FCA for deriving clustering solutions from multiple gene expression matrices. The experimental results presented herein demonstrate that it is a robust data integration technique able to produce good quality clustering solution that is representative for the whole set of expression matrices. PMID:24885407

Bottlenecks of the wavefront sensor based on the Talbot effect.

PubMed

Podanchuk, Dmytro; Kovalenko, Andrey; Kurashov, Vitalij; Kotov, Myhaylo; Goloborodko, Andrey; Danko, Volodymyr

2014-04-01

Physical constraints and peculiarities of the wavefront sensing technique, based on the Talbot effect, are discussed. The limitation on the curvature of the measurable wavefront is derived. The requirements to the Fourier spectrum of the periodic mask are formulated. Two kinds of masks are studied for their performance in the wavefront sensor. It is shown that the boundary part of the mask aperture does not contribute to the initial data for wavefront restoration. It is verified by experiment and computer simulation that the performance of the Talbot sensor, which meets established conditions, is similar to that of the Shack-Hartmann sensor.

Problem-based learning biotechnology courses in chemical engineering.

PubMed

Glatz, Charles E; Gonzalez, Ramon; Huba, Mary E; Mallapragada, Surya K; Narasimhan, Balaji; Reilly, Peter J; Saunders, Kevin P; Shanks, Jacqueline V

2006-01-01

We have developed a series of upper undergraduate/graduate lecture and laboratory courses on biotechnological topics to supplement existing biochemical engineering, bioseparations, and biomedical engineering lecture courses. The laboratory courses are based on problem-based learning techniques, featuring two- and three-person teams, journaling, and performance rubrics for guidance and assessment. Participants initially have found them to be difficult, since they had little experience with problem-based learning. To increase enrollment, we are combining the laboratory courses into 2-credit groupings and allowing students to substitute one of them for the second of our 2-credit chemical engineering unit operations laboratory courses.

Overview of Mission Design for NASA Asteroid Redirect Robotic Mission Concept

NASA Technical Reports Server (NTRS)

Strange, Nathan; Landau, Damon; McElrath, Timothy; Lantoine, Gregory; Lam, Try; McGuire, Melissa; Burke, Laura; Martini, Michael; Dankanich, John

2013-01-01

Part of NASA's new asteroid initiative would be a robotic mission to capture a roughly four to ten meter asteroid and redirect its orbit to place it in translunar space. Once in a stable storage orbit at the Moon, astronauts would then visit the asteroid for science investigations, to test in space resource extraction, and to develop experience with human deep space missions. This paper discusses the mission design techniques that would enable the redirection of a 100-1000 metric ton asteroid into lunar orbit with a 40-50 kW Solar Electric Propulsion (SEP) system.

Biologically-Inspired Concepts for Self-Management of Complexity

NASA Technical Reports Server (NTRS)

Sterritt, Roy; Hinchey, G.

2006-01-01

Inherent complexity in large-scale applications may be impossible to eliminate or even ameliorate despite a number of promising advances. In such cases, the complexity must be tolerated and managed. Such management may be beyond the abilities of humans, or require such overhead as to make management by humans unrealistic. A number of initiatives inspired by concepts in biology have arisen for self-management of complex systems. We present some ideas and techniques we have been experimenting with, inspired by lesser-known concepts in biology that show promise in protecting complex systems and represent a step towards self-management of complexity.

Laying the cornerstone: an employee-driven customer service program.

PubMed

Davis, Stephen M; Chinnis, Ann S; Dunmire, J Erin

2006-01-01

In the 21st-century healthcare environment, customer service remains critical to the fiscal viability of healthcare organizations. Continued competition for patients and diminishing reimbursements have necessitated the establishment of customer service programs to attract patients and retain outstanding employees. These programs should increase quality experiences for both internal customers (employees) and external customers (patients). This article describes a unique employee-driven customer service initiative titled Serving Together Achieving Results. Obstacles to implementing a customer service program in a multifaceted academic setting are highlighted, and the use of a novel tool, Q technique, to prioritize employee feedback is discussed.

Lunar surface magnetometer experiment

NASA Technical Reports Server (NTRS)

Dyal, P.; Parkin, C. W.; Colburn, D. S.; Schubert, G.

1972-01-01

The Apollo 16 lunar surface magnetometer (LSM) activation completed the network installation of magnetic observatories on the lunar surface and initiated simultaneous measurements of the global response of the moon to large-scale solar and terrestrial magnetic fields. Fossil remanent magnetic fields have been measured at nine locations on the lunar surface, including the Apollo 16 LSM site in the Descartes highlands area. This fossil record indicates the possible existence of an ancient lunar dynamo or a solar or terrestrial field much stronger than exists at present. The experimental technique and operation of the LSM are described and the results obtained are discussed.

Dust control research for SEI. [Space Exploration Initiative

NASA Technical Reports Server (NTRS)

Kennedy, Kriss J.; Harris, Jeffrey R.

1992-01-01

A study, at NASA Johnson Space Center, of dust control requirements for surface habitats has focused on identification of the dust problem, identifying dust control techniques and dust control technology areas requiring research development. This research was performed for the Surface Habitats and Construction (SHAC) technology area. Dust control consists of two problems: (1) how to keep it out of the habitat; and (2) once the habitat or airlock is contaminated with dust, how to collect it. This paper describes the dust environment, the Apollo experience and dust control methods used, future EVA operational considerations, and dust control concepts for surface habitats.

The initiation, propagation, and effect of matrix microcracks in cross-ply and related laminates

NASA Technical Reports Server (NTRS)

Nairn, John A.; Hu, Shoufeng; Liu, Siulie; Bark, Jong

1991-01-01

Recently, a variational mechanics approach was used to determine the thermoelastic stress state in cracked laminates. Described here is a generalization of the variational mechanics techniques to handle other cross-ply laminates, related laminates, and to account for delaminations emanating from microcrack tips. Microcracking experiments on Hercules 3501-6/AS4 carbon fiber/epoxy laminates show a staggered cracking pattern. These results can be explained by the variational mechanics analysis. The analysis of delaminations emanating from microcrack tips has resulted in predictions about the structural and material variables controlling competition between microcracking and delamination failure modes.

A hybrid monkey search algorithm for clustering analysis.

PubMed

Chen, Xin; Zhou, Yongquan; Luo, Qifang

2014-01-01

Clustering is a popular data analysis and data mining technique. The k-means clustering algorithm is one of the most commonly used methods. However, it highly depends on the initial solution and is easy to fall into local optimum solution. In view of the disadvantages of the k-means method, this paper proposed a hybrid monkey algorithm based on search operator of artificial bee colony algorithm for clustering analysis and experiment on synthetic and real life datasets to show that the algorithm has a good performance than that of the basic monkey algorithm for clustering analysis.

Direct measurement of the initial proton extrusion to oxygen uptake ratio accompanying succinate oxidation by rat liver mitochondria.

PubMed Central

Setty, O H; Shrager, R I; Bunow, B; Reynafarje, B; Lehninger, A L; Hendler, R W

1986-01-01

The problem of obtaining very early ratios for the H+/O stoichiometry accompanying succinate oxidation by rat liver mitochondria was attacked using new techniques for direct measurement rather than extrapolations based on data obtained after mixing and the recovery of the electrode from initial injection of O2. Respiration was quickly initiated in a thoroughly mixed O2-containing suspension of mitochondria under a CO atmosphere by photolysis of the CO-cytochrome c oxidase complex-. Fast responding O2 and pH electrodes were used to collect data every 10 ms. The response time for each electrode was experimentally measured in each experiment and suitable corrections for electrode relaxations were made. With uncorrected data obtained after 0.8 s, the extrapolation back to zero time on the basis of single-exponential curve fitting confirmed values close to 8.0 as previously reported (Costa et al., 1984). The data directly obtained, however, indicate an initial burst in H+/O ratio that peaked to values of approximately 20 to 30 prior to 50 ms and which was no longer evident after 0.3 s. Newer information and considerations that place all extrapolation methods in question are discussed. PMID:3019443

Comparing State-Space Multivariable Controls to Multi-SISO Controls for Load Reduction of Drivetrain-Coupled Modes on Wind Turbines through Field-Testing: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fleming, P. A.; van Wingerden, J. W.; Wright, A. D.

2011-12-01

This paper presents the structure of an ongoing controller comparison experiment at NREL's National Wind Technology Center; the design process for the two controllers compared in this phase of the experiment, and initial comparison results obtained in field-testing. The intention of the study is to demonstrate the advantage of using modern multivariable methods for designing control systems for wind turbines versus conventional approaches. We will demonstrate the advantages through field-test results from experimental turbines located at the NWTC. At least two controllers are being developed side-by-side to meet an incrementally increasing number of turbine load-reduction objectives. The first, a multiplemore » single-input, single-output (m-SISO) approach, uses separately developed decoupled and classicially tuned controllers, which is, to the best of our knowledge, common practice in the wind industry. The remaining controllers are developed using state-space multiple-input and multiple-output (MIMO) techniques to explicity account for coupling between loops and to optimize given known frequency structures of the turbine and disturbance. In this first publication from the study, we present the structure of the ongoing controller comparison experiment, the design process for the two controllers compared in this phase, and initial comparison results obtained in field-testing.« less

Adiabat-shaping in indirect drive inertial confinement fusion

DOE PAGES

Baker, K. L.; Robey, H. F.; Milovich, J. L.; ...

2015-05-05

Adiabat-shaping techniques were investigated in this paper in indirect drive inertial confinement fusion experiments on the National Ignition Facility as a means to improve implosion stability, while still maintaining a low adiabat in the fuel. Adiabat-shaping was accomplished in these indirect drive experiments by altering the ratio of the picket and trough energies in the laser pulse shape, thus driving a decaying first shock in the ablator. This decaying first shock is designed to place the ablation front on a high adiabat while keeping the fuel on a low adiabat. These experiments were conducted using the keyhole experimental platform formore » both three and four shock laser pulses. This platform enabled direct measurement of the shock velocities driven in the glow-discharge polymer capsule and in the liquid deuterium, the surrogate fuel for a DT ignition target. The measured shock velocities and radiation drive histories are compared to previous three and four shock laser pulses. This comparison indicates that in the case of adiabat shaping the ablation front initially drives a high shock velocity, and therefore, a high shock pressure and adiabat. The shock then decays as it travels through the ablator to pressures similar to the original low-adiabat pulses when it reaches the fuel. Finally, this approach takes advantage of initial high ablation velocity, which favors stability, and high-compression, which favors high stagnation pressures.« less

Robot-assisted general surgery.

PubMed

Hazey, Jeffrey W; Melvin, W Scott

2004-06-01

With the initiation of laparoscopic techniques in general surgery, we have seen a significant expansion of minimally invasive techniques in the last 16 years. More recently, robotic-assisted laparoscopy has moved into the general surgeon's armamentarium to address some of the shortcomings of laparoscopic surgery. AESOP (Computer Motion, Goleta, CA) addressed the issue of visualization as a robotic camera holder. With the introduction of the ZEUS robotic surgical system (Computer Motion), the ability to remotely operate laparoscopic instruments became a reality. US Food and Drug Administration approval in July 2000 of the da Vinci robotic surgical system (Intuitive Surgical, Sunnyvale, CA) further defined the ability of a robotic-assist device to address limitations in laparoscopy. This includes a significant improvement in instrument dexterity, dampening of natural hand tremors, three-dimensional visualization, ergonomics, and camera stability. As experience with robotic technology increased and its applications to advanced laparoscopic procedures have become more understood, more procedures have been performed with robotic assistance. Numerous studies have shown equivalent or improved patient outcomes when robotic-assist devices are used. Initially, robotic-assisted laparoscopic cholecystectomy was deemed safe, and now robotics has been shown to be safe in foregut procedures, including Nissen fundoplication, Heller myotomy, gastric banding procedures, and Roux-en-Y gastric bypass. These techniques have been extrapolated to solid-organ procedures (splenectomy, adrenalectomy, and pancreatic surgery) as well as robotic-assisted laparoscopic colectomy. In this chapter, we review the evolution of robotic technology and its applications in general surgical procedures.

Magnetically Induced Rotating Rayleigh-Taylor Instability.

PubMed

Scase, Matthew M; Baldwin, Kyle A; Hill, Richard J A

2017-03-03

Classical techniques for investigating the Rayleigh-Taylor instability include using compressed gasses 1 , rocketry 2 or linear electric motors 3 to reverse the effective direction of gravity, and accelerate the lighter fluid toward the denser fluid. Other authors e.g. 4 , 5 , 6 have separated a gravitationally unstable stratification with a barrier that is removed to initiate the flow. However, the parabolic initial interface in the case of a rotating stratification imposes significant technical difficulties experimentally. We wish to be able to spin-up the stratification into solid-body rotation and only then initiate the flow in order to investigate the effects of rotation upon the Rayleigh-Taylor instability. The approach we have adopted here is to use the magnetic field of a superconducting magnet to manipulate the effective weight of the two liquids to initiate the flow. We create a gravitationally stable two-layer stratification using standard flotation techniques. The upper layer is less dense than the lower layer and so the system is Rayleigh-Taylor stable. This stratification is then spun-up until both layers are in solid-body rotation and a parabolic interface is observed. These experiments use fluids with low magnetic susceptibility, |χ| ~ 10 -6 - 10 -5 , compared to a ferrofluids. The dominant effect of the magnetic field applies a body-force to each layer changing the effective weight. The upper layer is weakly paramagnetic while the lower layer is weakly diamagnetic. When the magnetic field is applied, the lower layer is repelled from the magnet while the upper layer is attracted towards the magnet. A Rayleigh-Taylor instability is achieved with application of a high gradient magnetic field. We further observed that increasing the dynamic viscosity of the fluid in each layer, increases the length-scale of the instability.

The Influence of Soil Moisture and Wind on Rainfall Distribution and Intensity in Florida

NASA Technical Reports Server (NTRS)

Baker, R. David; Lynn, Barry H.; Boone, Aaron; Tao, Wei-Kuo

1998-01-01

Land surface processes play a key role in water and energy budgets of the hydrological cycle. For example, the distribution of soil moisture will affect sensible and latent heat fluxes, which in turn may dramatically influence the location and intensity of precipitation. However, mean wind conditions also strongly influence the distribution of precipitation. The relative importance of soil moisture and wind on rainfall location and intensity remains uncertain. Here, we examine the influence of soil moisture distribution and wind distribution on precipitation in the Florida peninsula using the 3-D Goddard Cumulus Ensemble (GCE) cloud model Coupled with the Parameterization for Land-Atmosphere-Cloud Exchange (PLACE) land surface model. This study utilizes data collected on 27 July 1991 in central Florida during the Convection and Precipitation Electrification Experiment (CaPE). The idealized numerical experiments consider a block of land (the Florida peninsula) bordered on the east and on the west by ocean. The initial soil moisture distribution is derived from an offline PLACE simulation, and the initial environmental wind profile is determined from the CaPE sounding network. Using the factor separation technique, the precise contribution of soil moisture and wind to rainfall distribution and intensity is determined.

Holmium laser use in debridement of stable labral lesions: two-year experience in initial 50 patients

NASA Astrophysics Data System (ADS)

Dew, Douglas K.; Risch, E. David

1994-09-01

The purpose of this study is to determine the laser related complication rate for shoulder arthroscopy in the initial clinical experience of 50 patients, and to identify potential advantages of laser use in shoulder arthroscopy. Fifty patients spanning ages 25 to 87 were treated. Surgical debridement was selective and conservative creating a smooth post resection rim. In those that included rotator cuff tears, in addition to arthroscopic debridement, a mini arthrotomy and open acromioplasty were performed. Changes in arthroscopic technique due to laser use included no arthroscopic pump use and use of the shaver only when the fiber could not be easily seen with severe synovitis. We found that the hyper-vascular synovium did not need to be resected last, it could be resected at any point during the procedure. Four hundred and 600 micron fiberoptics were used as well as 20 watts average power. Technical advantage of the laser was felt to be the size of the instrument probe and the availability of excellent hemostasis. Complications include one case of arthroscope damage and one case with a broken fiber tip which was removed with a grasper. Long term follow up of these patients is now underway.

Hydrodynamic instability experiments with three-dimensional modulations at the National Ignition Facility

DOE PAGES

Smalyuk, V. A.; Weber, S. V.; Casey, D. T.; ...

2015-06-18

The first hydrodynamic instability growth measurements with three-dimensional (3D) surface-roughness modulations were performed on CH shell spherical implosions at the National Ignition Facility (NIF) [G. H. Miller, E. I. Moses, and C. R. Wuest, Opt. Eng. 43, 2841 (2004)]. The initial capsule outer-surface amplitudes were increased approximately four times, compared with the standard specifications, to increase the signal-to-noise ratio, helping to qualify a technique for measuring small 3D modulations. The instability growth measurements were performed using x-ray through-foil radiography based on time-resolved pinhole imaging. Averaging over 15 similar images significantly increased the signal-to-noise ratio, making possible a comparison with 3Dmore » simulations. At a convergence ratio of ~2.4, the measured modulation levels were ~3 times larger than those simulated based on the growth of the known imposed initial surface modulations. Several hypotheses are discussed, including increased instability growth due to modulations of the oxygen content in the bulk of the capsule. In conclusion, future experiments will be focused on measurements with standard 3D ‘native-roughness’ capsules as well as with deliberately imposed oxygen modulations.« less

Computed torque control of a free-flying cooperat ing-arm robot

NASA Technical Reports Server (NTRS)

Koningstein, Ross; Ullman, Marc; Cannon, Robert H., Jr.

1989-01-01

The unified approach to solving free-floating space robot manipulator end-point control problems is presented using a control formulation based on an extension of computed torque. Once the desired end-point accelerations have been specified, the kinematic equations are used with momentum conservation equations to solve for the joint accelerations in any of the robot's possible configurations: fixed base or free-flying with open/closed chain grasp. The joint accelerations can then be used to calculate the arm control torques and internal forces using a recursive order N algorithm. Initial experimental verification of these techniques has been performed using a laboratory model of a two-armed space robot. This fully autonomous spacecraft system experiences the drag-free, zero G characteristics of space in two dimensions through the use of an air cushion support system. Results of these initial experiments are included which validate the correctness of the proposed methodology. The further problem of control in the large where not only the manipulator tip positions but the entire system consisting of base and arms must be controlled is also presented. The availability of a physical testbed has brought a keener insight into the subtleties of the problem at hand.

Speech pathologists' current practice with cognitive-communication assessment during post-traumatic amnesia: a survey.

PubMed

Steel, Joanne; Ferguson, Alison; Spencer, Elizabeth; Togher, Leanne

2013-01-01

To investigate speech pathologists' current practice with adults who are in post-traumatic amnesia (PTA). Speech pathologists with experience of adults in PTA were invited to take part in an online survey through Australian professional email/internet-based interest groups. Forty-five speech pathologists responded to the online survey. The majority of respondents (78%) reported using informal, observational assessment methods commencing at initial contact with people in PTA or when patients' level of alertness allowed and initiating formal assessment on emergence from PTA. Seven respondents (19%) reported undertaking no assessment during PTA. Clinicians described using a range of techniques to monitor cognitive-communication during PTA, including static, dynamic, functional and impairment-based methods. The study confirmed that speech pathologists have a key role in the multidisciplinary team caring for the person in PTA, especially with family education and facilitating interactions with the rehabilitation team and family. Decision-making around timing and means of assessment of cognitive-communication during PTA appeared primarily reliant on speech pathologists' professional experience and the culture of their workplace. The findings support the need for further research into the nature of cognitive-communication disorder and resolution over this period.

Advanced flight hardware for organic separations using aqueous two-phase partitioning

NASA Astrophysics Data System (ADS)

Deuser, Mark S.; Vellinger, John C.; Weber, John T.

1996-03-01

Separation of cells and cell components is the limiting factor in many biomedical research and pharmaceutical development processes. Aqueous Two-Phase Partitioning (ATPP) is a unique separation technique which allows purification and classification of biological materials. SHOT has employed the ATPP process in separation equipment developed for both space and ground applications. Initial equipment development and research focused on the ORganic SEParation (ORSEP) space flight experiments that were performed on suborbital rockets and the shuttle. ADvanced SEParations (ADSEP) technology was developed as the next generation of ORSEP equipment through a NASA Small Business Innovation Research (SBIR) contract. Under the SBIR contract, a marketing study was conducted, indicating a growing commercial market exists among biotechnology firms for ADSEP equipment and associated flight research and development services. SHOT is preparing to begin manufacturing and marketing laboratory versions of the ADSEP hardware for the ground-based market. In addition, through a self-financed SBIR Phase III effort, SHOT is fabricating and integrating the ADSEP flight hardware for a commercially-driven SPACEHAB 04 experiment that will be the initial step in marketing space separations services. The ADSEP ground-based and microgravity research is expected to play a vital role in developing important new biomedical and pharmaceutical products.

Lateral Transorbital Endoscopic Access to the Hippocampus, Amygdala, and Entorhinal Cortex: Initial Clinical Experience.

PubMed

Chen, H Isaac; Bohman, Leif-Erik; Emery, Lyndsey; Martinez-Lage, Maria; Richardson, Andrew G; Davis, Kathryn A; Pollard, John R; Litt, Brian; Gausas, Roberta E; Lucas, Timothy H

2015-01-01

Transorbital approaches traditionally have focused on skull base and cavernous sinus lesions medial to the globe. Lateral orbital approaches to the temporal lobe have not been widely explored despite several theoretical advantages compared to open craniotomy. Recently, we demonstrated the feasibility of the lateral transorbital technique in cadaveric specimens with endoscopic visualization. We describe our initial clinical experience with the endoscope-assisted lateral transorbital approach to lesions in the temporal lobe. Two patients with mesial temporal lobe pathology presenting with seizures underwent surgery. The use of a transpalpebral or Stallard-Wright eyebrow incision enabled access to the intraorbital compartment, and a lateral orbital wall 'keyhole' opening permitted visualization of the anterior temporal pole. This approach afforded adequate access to the surgical target and surrounding structures and was well tolerated by the patients. To the best of our knowledge, this report constitutes the first case series describing the endoscope-assisted lateral transorbital approach to the temporal lobe. We discuss the limits of exposure, the nuances of opening and closing, and comparisons to open craniotomy. Further prospective investigation of this approach is warranted for comparison to traditional approaches to the mesial temporal lobe. © 2015 S. Karger AG, Basel.

An initial investigation of the sub-microsecond features of dynamic crack propagation in PMMA and the RDX-based explosive PBX 9205

NASA Astrophysics Data System (ADS)

Washabaugh, Peter; Hill, Larry

2007-06-01

A dynamic crack propagating in a brittle material releases enough thermal energy to produce visible light. The dynamic fracture of even macroscopically amorphous materials becomes unsteady as the crack propagation velocity approaches the material wave-speeds. The heat generated at a crack-tip, especially as it jumps, may be a mechanism to initiate a self-sustaining reaction in an energetic material. Experiments were conducted in specimens to simulate an infinite plate for 20 μs. The initial specimens were 152 mm square by 6 mm thick acrylic sheets, and were fabricated to study non-steady near-wave-speed crack propagation. A variant of this specimen embedded a 25 mm x 3 mm PBX 9205 pellet to explore the influence of dynamic Mode-I cracks in these materials. The crack was initiated by up to 0.2 g of Detasheet placed along a precursor 50 mm long notch, with a shield to contain the reaction products and prevent propagation along the fractured surfaces. The crack was studied by means of a streak camera and a Fourier-filter of the light reflecting off the newly minted surfaces. The sub-microsecond behavior of holes initiating, preceding and coalescing with the main crack were observed in the PMMA samples. The embedding and mechanical loading of explosives by this technique did not initiate a self-sustaining reaction in preliminary testing.

Initial results from a multiple monoenergetic gamma radiography system for nuclear security

NASA Astrophysics Data System (ADS)

O'Day, Buckley E.; Hartwig, Zachary S.; Lanza, Richard C.; Danagoulian, Areg

2016-10-01

The detection of assembled nuclear devices and concealed special nuclear materials (SNM) such as plutonium or uranium in commercial cargo traffic is a major challenge in mitigating the threat of nuclear terrorism. Currently available radiographic and active interrogation systems use ∼1-10 MeV bremsstrahlung photon beams. Although simple to build and operate, bremsstrahlung-based systems deliver high radiation doses to the cargo and to potential stowaways. To eliminate problematic issues of high dose, we are developing a novel technique known as multiple monoenergetic gamma radiography (MMGR). MMGR uses ion-induced nuclear reactions to produce two monoenergetic gammas for dual-energy radiography. This allows us to image the areal density and effective atomic number (Zeff) of scanned cargo. We present initial results from the proof-of-concept experiment, which was conducted at the MIT Bates Research and Engineering Center. The purpose of the experiment was to assess the capabilities of MMGR to measure areal density and Zeff of container cargo mockups. The experiment used a 3.0 MeV radiofrequency quadrupole accelerator to create sources of 4.44 MeV and 15.11 MeV gammas from the 11B(d,nγ)12C reaction in a thick natural boron target; the gammas are detected by an array of NaI(Tl) detectors after transmission through cargo mockups . The measured fluxes of transmitted 4.44 MeV and 15.11 MeV gammas were used to assess the areal density and Zeff. Initial results show that MMGR is capable of discriminating the presence of high-Z materials concealed in up to 30 cm of iron shielding from low- and mid-Z materials present in the cargo mockup.

Validating an Air Traffic Management Concept of Operation Using Statistical Modeling

NASA Technical Reports Server (NTRS)

He, Yuning; Davies, Misty Dawn

2013-01-01

Validating a concept of operation for a complex, safety-critical system (like the National Airspace System) is challenging because of the high dimensionality of the controllable parameters and the infinite number of states of the system. In this paper, we use statistical modeling techniques to explore the behavior of a conflict detection and resolution algorithm designed for the terminal airspace. These techniques predict the robustness of the system simulation to both nominal and off-nominal behaviors within the overall airspace. They also can be used to evaluate the output of the simulation against recorded airspace data. Additionally, the techniques carry with them a mathematical value of the worth of each prediction-a statistical uncertainty for any robustness estimate. Uncertainty Quantification (UQ) is the process of quantitative characterization and ultimately a reduction of uncertainties in complex systems. UQ is important for understanding the influence of uncertainties on the behavior of a system and therefore is valuable for design, analysis, and verification and validation. In this paper, we apply advanced statistical modeling methodologies and techniques on an advanced air traffic management system, namely the Terminal Tactical Separation Assured Flight Environment (T-TSAFE). We show initial results for a parameter analysis and safety boundary (envelope) detection in the high-dimensional parameter space. For our boundary analysis, we developed a new sequential approach based upon the design of computer experiments, allowing us to incorporate knowledge from domain experts into our modeling and to determine the most likely boundary shapes and its parameters. We carried out the analysis on system parameters and describe an initial approach that will allow us to include time-series inputs, such as the radar track data, into the analysis

Advances in target design for heavy ion fusion

NASA Astrophysics Data System (ADS)

Callahan, D. A.; Tabak, M.; Bennett, G. R.; Cuneo, M. E.; Vesey, R. A.; Nikroo, A.; Czechowicz, D.; Steinman, D.

2005-12-01

Over the past few years, the emphasis in heavy ion target design has moved from the distributed radiator target to the 'hybrid' target because the hybrid target allows a larger beam focal spot than the distributed radiator (~5 mm radius rather than ~2 mm radius). The larger spot relaxes some of the requirements on the driver, but introduces some new target physics issues. Most notable is the use of shine shields and shims in the hohlraum to achieve symmetry rather than achieving symmetry by beam placement. The shim is a thin layer of material placed on or near the capsule surface to block a small amount of excess radiation. While we have been developing this technique for the heavy ion hybrid target, the technique can also be used in any indirect drive target. We have begun testing the concept of a shim to improve symmetry using a double-ended z-pinch hohlraum on the Sandia Z-machine. Experiments using shimmed thin wall capsules have shown that we can reverse the sign of a P2 asymmetry and significantly reduce the size of a P4 asymmetry. These initial experiments demonstrate the concept of a shim as another method for controlling early time asymmetries in ICF capsules.

Improvement of cutting performance for thick stainless steel plates by step-like cutting speed increase in high-power fiber laser cutting

NASA Astrophysics Data System (ADS)

Seon, Sangwoo; Shin, Jae Sung; Oh, Seong Yong; Park, Hyunmin; Chung, Chin-Man; Kim, Taek-Soo; Lee, Lim; Lee, Jonghwan

2018-07-01

A study was conducted to improve the cutting performance of a 60-mm thick stainless steel plate using a 6-kW fiber laser. Two techniques for improving the initial cutting performance were evaluated by preheating the work piece with a waiting time and step-like cutting speed increase. Both techniques showed improved cutting results compared to constant speed cutting. Among them, the method with a step-like cutting speed increase showed the better result in terms of cutting performance. As a result, a 60-mm thick stainless steel plate was cut at a maximum cutting speed of 72 mm/min with a preheating cutting speed of 24 mm/min. In order to confirm the effect of preheating, an additional experiment was performed to measure the temperature variation during the cutting process. Through this experiment, preheating temperature conditions were found to allow the specimen to be cut. It is expected that the results of this work will contribute to improving the cutting performance of thick metal structures in various industrial fields, as well as the dismantling of nuclear facilities using lasers in the future.

Experiences at Langley Research Center in the application of optimization techniques to helicopter airframes for vibration reduction

NASA Technical Reports Server (NTRS)

Murthy, T. Sreekanta; Kvaternik, Raymond G.

1991-01-01

A NASA/industry rotorcraft structural dynamics program known as Design Analysis Methods for VIBrationS (DAMVIBS) was initiated at Langley Research Center in 1984 with the objective of establishing the technology base needed by the industry for developing an advanced finite-element-based vibrations design analysis capability for airframe structures. As a part of the in-house activities contributing to that program, a study was undertaken to investigate the use of formal, nonlinear programming-based, numerical optimization techniques for airframe vibrations design work. Considerable progress has been made in connection with that study since its inception in 1985. This paper presents a unified summary of the experiences and results of that study. The formulation and solution of airframe optimization problems are discussed. Particular attention is given to describing the implementation of a new computational procedure based on MSC/NASTRAN and CONstrained function MINimization (CONMIN) in a computer program system called DYNOPT for the optimization of airframes subject to strength, frequency, dynamic response, and fatigue constraints. The results from the application of the DYNOPT program to the Bell AH-1G helicopter are presented and discussed.

The Sun in Time

NASA Technical Reports Server (NTRS)

Adams, Mitzi L.; Sever, Thomas L.; Bero, Elizabeth

1998-01-01

Using a grant from NASA's Initiative to Develop Education through Astronomy and Space Science (IDEAS) program, we have developed an inter-disciplinary curriculum for middle-school students which targets both history and astronomy. Our curriculum explores the attitudes and techniques of ancient spiritual leaders, specifically those of the Maya and Inca cultures, who observed and tried to control the Sun. We wish students to understand the probable importance of astronomical observations to these ancient peoples. In addition, using the experience of an archaeologist, we show how modern techniques of viewing the Earth through satellite imagery, has allowed the re-discovery of ancient sites where solar observations and attempted manipulation of the universe took place. To contrast ancient observations of the Sun with modern ones, we use the experience of a solar astronomer and bring to the classroom up-to-date information about solar astronomy and the impact of solar activity on the Earth's environment. In this presentation, we will present fragments of our curriculum as well as results from pre- and post-tests given to participating groups of students. Finally, we will discuss comments from local middle-school teachers who were asked to evaluate our curriculum.

Concentration variance decay during magma mixing: a volcanic chronometer.

PubMed

Perugini, Diego; De Campos, Cristina P; Petrelli, Maurizio; Dingwell, Donald B

2015-09-21

The mixing of magmas is a common phenomenon in explosive eruptions. Concentration variance is a useful metric of this process and its decay (CVD) with time is an inevitable consequence during the progress of magma mixing. In order to calibrate this petrological/volcanological clock we have performed a time-series of high temperature experiments of magma mixing. The results of these experiments demonstrate that compositional variance decays exponentially with time. With this calibration the CVD rate (CVD-R) becomes a new geochronometer for the time lapse from initiation of mixing to eruption. The resultant novel technique is fully independent of the typically unknown advective history of mixing - a notorious uncertainty which plagues the application of many diffusional analyses of magmatic history. Using the calibrated CVD-R technique we have obtained mingling-to-eruption times for three explosive volcanic eruptions from Campi Flegrei (Italy) in the range of tens of minutes. These in turn imply ascent velocities of 5-8 meters per second. We anticipate the routine application of the CVD-R geochronometer to the eruptive products of active volcanoes in future in order to constrain typical "mixing to eruption" time lapses such that monitoring activities can be targeted at relevant timescales and signals during volcanic unrest.

Development of advanced strain diagnostic techniques for reactor environments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fleming, Darryn D.; Holschuh, Thomas Vernon,; Miller, Timothy J.

2013-02-01

The following research is operated as a Laboratory Directed Research and Development (LDRD) initiative at Sandia National Laboratories. The long-term goals of the program include sophisticated diagnostics of advanced fuels testing for nuclear reactors for the Department of Energy (DOE) Gen IV program, with the future capability to provide real-time measurement of strain in fuel rod cladding during operation in situ at any research or power reactor in the United States. By quantifying the stress and strain in fuel rods, it is possible to significantly improve fuel rod design, and consequently, to improve the performance and lifetime of the cladding.more » During the past year of this program, two sets of experiments were performed: small-scale tests to ensure reliability of the gages, and reactor pulse experiments involving the most viable samples in the Annulated Core Research Reactor (ACRR), located onsite at Sandia. Strain measurement techniques that can provide useful data in the extreme environment of a nuclear reactor core are needed to characterize nuclear fuel rods. This report documents the progression of solutions to this issue that were explored for feasibility in FY12 at Sandia National Laboratories, Albuquerque, NM.« less

An Interpretative Study on Nurses' Perspectives of Working in an Overcrowded Emergency Department in Taiwan.

PubMed

Chen, Li-Chin; Lin, Chun-Chih; Han, Chin-Yen; Hsieh, Chun-Lan; Wu, Chiung-Jung Jo; Liang, Hwey-Fang

2018-03-01

This study aims to gain in-depth understanding of nurses' perspectives of working in an overcrowded emergency. Symbolic interactionism and Charmaz's construction of grounded theory were used. Purposive sampling at the start of the study and a further theoretical sampling by snowball technique were used to recruit 40 registered nurses (RN) to participate in in-depth, semi-structured interviews between May and November, 2014. Data analysis included analytic techniques of initial, focused and theoretical coding. Study findings showed searching for work role is derived by the themes of Finding the role of positioning in Emergency Department (ED), Recognizing causes of ED overcrowding, and Confined working environment. Nurses' work experience which represents the RNs not gained control over their work, as care actions influenced by the problematic overcrowded circumstance of the ED environment. The findings fill a gap in knowledge about how RNs experience their work role in the context of an overcrowded Emergency Department in Taiwan. Arising from the study result include taking account of nurses' perspectives when planning staff/patient ratios, strategies to reduce waiting time and ensure that clients receive appropriate care. Copyright © 2018. Published by Elsevier B.V.

Transanal dearterialization with targeted mucopexy is effective for advanced haemorrhoids.

PubMed

Giordano, P; Tomasi, I; Pascariello, A; Mills, E; Elahi, S

2014-05-01

Transanal haemorrhoidal dearterialization (THD) has become well established for the treatment of haemorrhoids. In this study we describe a technical modification of this technique, targeted mucopexy (THD TM), and report the results for advanced haemorrhoids. The study included a prospective evaluation of patients with Grade IV (fourth-degree) haemorrhoids operated on with the THD TM technique. This consisted of an initial dearterialization when the haemorrhoidal arteries were transfixed and a second phase of mucopexy, using a different needle from that usually used in the original technique. From January 2007 to December 2011, 31 consecutive patients with Grade IV haemorrhoids were operated on using the THD TM technique. Postoperative pain was reported by 22 (70%) patients on day 1 and 19 (61%) on day 7, while nine (30%) did not experience any pain at all. Severe pain was reported by only nine (16%) patients. At a mean follow-up of 32 months, two (6.4%) patients required a further intervention for on-going symptoms. Transanal haemorrhoidal dearterialization TM is effective for advanced haemorrhoids. © 2014 The Authors. Colorectal Disease published by John Wiley & Sons Ltd on behalf of Association of Coloproctology of Great Britain and Ireland.

Toward Studying Music Cognition with Information Retrieval Techniques: Lessons Learned from the OpenMIIR Initiative.

PubMed

Stober, Sebastian

2017-01-01

As an emerging sub-field of music information retrieval (MIR), music imagery information retrieval (MIIR) aims to retrieve information from brain activity recorded during music cognition-such as listening to or imagining music pieces. This is a highly inter-disciplinary endeavor that requires expertise in MIR as well as cognitive neuroscience and psychology. The OpenMIIR initiative strives to foster collaborations between these fields to advance the state of the art in MIIR. As a first step, electroencephalography (EEG) recordings of music perception and imagination have been made publicly available, enabling MIR researchers to easily test and adapt their existing approaches for music analysis like fingerprinting, beat tracking or tempo estimation on this new kind of data. This paper reports on first results of MIIR experiments using these OpenMIIR datasets and points out how these findings could drive new research in cognitive neuroscience.

Dismantling of the PETRA glove box: tritium contamination and inventory assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, R.

2015-03-15

The PETRA facility is the first installation in which experiments with tritium were carried out at the Tritium Laboratory Karlsruhe. After completion of two main experimental programs, the decommissioning of PETRA was initiated with the aim to reuse the glove box and its main still valuable components. A decommissioning plan was engaged to: -) identify the source of tritium release in the glove box, -) clarify the status of the main components, -) assess residual tritium inventories, and -) de-tritiate the components to be disposed of as waste. Several analytical techniques - calorimetry on small solid samples, wipe test followedmore » by liquid scintillation counting for surface contamination assessment, gas chromatography on gaseous samples - were deployed and cross-checked to assess the remaining tritium inventories and initiate the decommissioning process. The methodology and the main outcomes of the numerous different tritium measurements are presented and discussed. (authors)« less

A potential-energy scaling model to simulate the initial stages of thin-film growth

NASA Technical Reports Server (NTRS)

Heinbockel, J. H.; Outlaw, R. A.; Walker, G. H.

1983-01-01

A solid on solid (SOS) Monte Carlo computer simulation employing a potential energy scaling technique was used to model the initial stages of thin film growth. The model monitors variations in the vertical interaction potential that occur due to the arrival or departure of selected adatoms or impurities at all sites in the 400 sq. ft. array. Boltzmann ordered statistics are used to simulate fluctuations in vibrational energy at each site in the array, and the resulting site energy is compared with threshold levels of possible atomic events. In addition to adsorption, desorption, and surface migration, adatom incorporation and diffusion of a substrate atom to the surface are also included. The lateral interaction of nearest, second nearest, and third nearest neighbors is also considered. A series of computer experiments are conducted to illustrate the behavior of the model.

On the characteristics of landslide tsunamis

PubMed Central

Løvholt, F.; Pedersen, G.; Harbitz, C. B.; Glimsdal, S.; Kim, J.

2015-01-01

This review presents modelling techniques and processes that govern landslide tsunami generation, with emphasis on tsunamis induced by fully submerged landslides. The analysis focuses on a set of representative examples in simplified geometries demonstrating the main kinematic landslide parameters influencing initial tsunami amplitudes and wavelengths. Scaling relations from laboratory experiments for subaerial landslide tsunamis are also briefly reviewed. It is found that the landslide acceleration determines the initial tsunami elevation for translational landslides, while the landslide velocity is more important for impulsive events such as rapid slumps and subaerial landslides. Retrogressive effects stretch the tsunami, and in certain cases produce enlarged amplitudes due to positive interference. In an example involving a deformable landslide, it is found that the landslide deformation has only a weak influence on tsunamigenesis. However, more research is needed to determine how landslide flow processes that involve strong deformation and long run-out determine tsunami generation. PMID:26392615

Experiences in using DISCUS for visualizing human communication

NASA Astrophysics Data System (ADS)

Groehn, Matti; Nieminen, Marko; Haho, Paeivi; Smeds, Riitta

2000-02-01

In this paper, we present further improvement to the DISCUS software that can be used to record and analyze the flow and constants of business process simulation session discussion. The tool was initially introduced in 'visual data exploration and analysis IV' conference. The initial features of the tool enabled the visualization of discussion flow in business process simulation sessions and the creation of SOM analyses. The improvements of the tool consists of additional visualization possibilities that enable quick on-line analyses and improved graphical statistics. We have also created the very first interface to audio data and implemented two ways to visualize it. We also outline additional possibilities to use the tool in other application areas: these include usability testing and the possibility to use the tool for capturing design rationale in a product development process. The data gathered with DISCUS may be used in other applications, and further work may be done with data ming techniques.

On the characteristics of landslide tsunamis.

PubMed

Løvholt, F; Pedersen, G; Harbitz, C B; Glimsdal, S; Kim, J

2015-10-28

This review presents modelling techniques and processes that govern landslide tsunami generation, with emphasis on tsunamis induced by fully submerged landslides. The analysis focuses on a set of representative examples in simplified geometries demonstrating the main kinematic landslide parameters influencing initial tsunami amplitudes and wavelengths. Scaling relations from laboratory experiments for subaerial landslide tsunamis are also briefly reviewed. It is found that the landslide acceleration determines the initial tsunami elevation for translational landslides, while the landslide velocity is more important for impulsive events such as rapid slumps and subaerial landslides. Retrogressive effects stretch the tsunami, and in certain cases produce enlarged amplitudes due to positive interference. In an example involving a deformable landslide, it is found that the landslide deformation has only a weak influence on tsunamigenesis. However, more research is needed to determine how landslide flow processes that involve strong deformation and long run-out determine tsunami generation. © 2015 The Authors.

Digital Topographic Mapping in Urban Obstructed Environment Based on Multi-GNSS Network RTK Technology

NASA Astrophysics Data System (ADS)

Guo, Qiuying; Zhao, Tonglong; Zhang, Chao; Wu, Xuxiang

2017-10-01

Digital topographic mapping experiments were carried out based on network RTK technology using GPS/BEIDOU/GLONASS multi-constellation compatible GNSS receivers in urban obstructed environment. Operation scheme and technique flow were discussed. Experimental results show that the horizontal position and elevation of the points measured by RTK can reach 2cm and 3cm precision level respectively in open environment. RTK initialization time needs about 3-5s. While in obstructed environment, such as high building and tree shanding, the RTK initialization time needs about dozens of seconds or tens of seconds, and sometimes floating solutions or even differential solutions were obtained. The impact of dense and tall building on RTK measurement is more seriously. It is more likely to get RTK fixed solution in the south side of high building than the north side of the building.

Experiments on the heat-induced salt balance changes in cow's milk.

PubMed

Pouliot, Y; Boulet, M; Paquin, P

1989-01-01

The heat-induced changes in salt balance between the colloidal phase of milk and its serum were studied using an ultrafiltration technique. Milk permeate was isolated at the heating temperature by means of a hollow fibre ultrafiltration cartridge coupled with a stainless steel heat exchanger unit. The milk samples initially at 4 degrees C were heated to 20, 40, 60, 80 or 90 degrees C. Ca, P, Mg and citrate contents of the permeates were determined. The decreases in Ca and P were proportional to the increase in temperature. Smaller losses in Mg and citrate were observed. An initial sharp decrease in concentration occurred within the first seconds of holding time and was followed by a slower and smaller decrease. The possible occurrence of a two-stage mechanism for the heat-induced salt precipitation is discussed. The precipitation of dicalcium phosphate is believed to occur together with some tricalcium citrate precipitation.

Toward Studying Music Cognition with Information Retrieval Techniques: Lessons Learned from the OpenMIIR Initiative

PubMed Central

Stober, Sebastian

2017-01-01

As an emerging sub-field of music information retrieval (MIR), music imagery information retrieval (MIIR) aims to retrieve information from brain activity recorded during music cognition–such as listening to or imagining music pieces. This is a highly inter-disciplinary endeavor that requires expertise in MIR as well as cognitive neuroscience and psychology. The OpenMIIR initiative strives to foster collaborations between these fields to advance the state of the art in MIIR. As a first step, electroencephalography (EEG) recordings of music perception and imagination have been made publicly available, enabling MIR researchers to easily test and adapt their existing approaches for music analysis like fingerprinting, beat tracking or tempo estimation on this new kind of data. This paper reports on first results of MIIR experiments using these OpenMIIR datasets and points out how these findings could drive new research in cognitive neuroscience. PMID:28824478

Collapsing Radiative Shocks in Xenon Gas on the Omega Laser

NASA Astrophysics Data System (ADS)

Reighard, A. B.; Glendinning, S. G.; Knauer, J.; Bouquet, S.; Koenig, M.

2005-10-01

A number of astrophysical systems involve radiative shocks that collapse spatially in response to energy lost through radiation, producing thin shells believed to be Vishniac unstable. We report experiments intended to study such collapsing shocks. The Omega laser drives a thin slab of material at >100 km/s through Xe gas. Simulations predict a collapsed layer in which the density reaches 45 times initial density. X-ray backlighting techniques have yielded images of a collapsed shock compressed to <1/25 its initial thickness (45 μm) at a speed of ˜100 km/s when the shock has traveled 1.3 mm. Optical depth before and behind the shock is important for comparison to astrophysical systems. This research was sponsored by the National Nuclear Security Administration under the Stewardship Science Academic Alliances program through DOE Research Grants DE-FG52-03NA00064, DE-FG53-2005-NA26014, and other grants and contracts.

Water flow algorithm decision support tool for travelling salesman problem

NASA Astrophysics Data System (ADS)

Kamarudin, Anis Aklima; Othman, Zulaiha Ali; Sarim, Hafiz Mohd

2016-08-01

This paper discuss about the role of Decision Support Tool in Travelling Salesman Problem (TSP) for helping the researchers who doing research in same area will get the better result from the proposed algorithm. A study has been conducted and Rapid Application Development (RAD) model has been use as a methodology which includes requirement planning, user design, construction and cutover. Water Flow Algorithm (WFA) with initialization technique improvement is used as the proposed algorithm in this study for evaluating effectiveness against TSP cases. For DST evaluation will go through usability testing conducted on system use, quality of information, quality of interface and overall satisfaction. Evaluation is needed for determine whether this tool can assists user in making a decision to solve TSP problems with the proposed algorithm or not. Some statistical result shown the ability of this tool in term of helping researchers to conduct the experiments on the WFA with improvements TSP initialization.

Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures

NASA Technical Reports Server (NTRS)

Hovel, H. J.; Vernon, S. M.

1982-01-01

The power to weight ratio of GaAs cells can be reduced by fabricating devices using thin GaAs films on low density substrate materials (silicon, glass, plastics). A graphoepitaxy technique was developed which uses fine geometric patterns in the substrate to affect growth. Initial substrates were processed by etching 25 microns deep grooves into 100 oriented wafers; fine-grained polycrystalline GaAs layers 25-50 microns thick were then deposited on these and recrystallization was performed, heating the substrates to above the GaAs melting point in ASH3 atmosphere, resulting in large grain regrowth oriented along the groove dimensions. Experiments with smaller groove depths and spacings were initially encouraging; single large GaAs grains would totally cover one and often two groove fields of 14 groove each spanning several hundred microns. Dielectric coatings on the grooved substrates were also used to modify the growth.

Three-dimensional face pose detection and tracking using monocular videos: tool and application.

PubMed

Dornaika, Fadi; Raducanu, Bogdan

2009-08-01

Recently, we have proposed a real-time tracker that simultaneously tracks the 3-D head pose and facial actions in monocular video sequences that can be provided by low quality cameras. This paper has two main contributions. First, we propose an automatic 3-D face pose initialization scheme for the real-time tracker by adopting a 2-D face detector and an eigenface system. Second, we use the proposed methods-the initialization and tracking-for enhancing the human-machine interaction functionality of an AIBO robot. More precisely, we show how the orientation of the robot's camera (or any active vision system) can be controlled through the estimation of the user's head pose. Applications based on head-pose imitation such as telepresence, virtual reality, and video games can directly exploit the proposed techniques. Experiments on real videos confirm the robustness and usefulness of the proposed methods.

Rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium distribution coefficients of a surficial sediment at the Idaho National Engineering Laboratory, Idaho

USGS Publications Warehouse

Bunde, R.L.; Rosentreter, J.J.; Liszewski, M.J.

1998-01-01

The rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium sorption were measured as part of an investigation to determine strontium chemical transport properties of a surficial sediment at the Idaho National Engineering Laboratory (INEL), Idaho. Batch experimental techniques were used to determine the rate of strontium sorption and strontium distribution coefficients (K(d)s) between aqueous and solid phases. Rate experiments indicate that strontium in solution reached an apparent equilibrium with the sediment in 26 h. K(d)s were derived using the linear isotherm model at initial sodium concentrations from 100 to 5,000 mg/l and initial potassium concentrations from 2 to 150 mg/l. K(d)s ranged from 56 ?? 2 to 62 ?? 3 ml/g at initial aqueous concentrations of sodium and potassium equal to or less than 300 and 150 mg/l, respectively. K(d)s hinged from 4.7 ?? 0.2 to 19 ?? 1 ml/g with initial aqueous concentrations of sodium between 1,000 and 5,000 mg/l. These data indicate that sodium concentrations greater than 300 mg/l in wastewater increase the availability of strontium for transport beneath waste disposal ponds at the INEL by decreasing strontium sorption on the surficial sediment. Wastewater concentrations of sodium and potassium less than 300 and 150 mg/l, respectively, have little effect on the availability of strontium for transport.The rate of strontium sorption and the effects of variable aqueous concentrations of sodium and potassium on strontium sorption were measured as part of an investigation to determine strontium chemical transport properties of a surficial sediment at the Idaho National Engineering Laboratory (INEL), Idaho. Batch experimental techniques were used to determine the rate of strontium sorption and strontium distribution coefficients (Kds) between aqueous and solid phases. Rate experiments indicate that strontium in solution reached an apparent equilibrium with the sediment in 26 h. Kds were derived using the linear isotherm model at initial sodium concentrations from 100 to 5,000 mg/l and initial potassium concentrations from 2 to 150 mg/l. Kds ranged from 56??2 to 62??3 ml/g at initial aqueous concentrations of sodium and potassium equal to or less than 300 and 150 mg/l, respectively. Kds ranged from 4.7??0.2 to 19??1 ml/g with initial aqueous concentrations of sodium between 1,000 and 5,000 mg/l. These data indicate that sodium concentrations greater than 300 mg/l in wastewater increase the availability of strontium for transport beneath waste disposal ponds at the INEL by decreasing strontium sorption on the surficial sediment. Wastewater concentrations of sodium and potassium less than 300 and 150 mg/l, respectively, have little effect on the availability of strontium for transport.

Creating opportunities to influence self-efficacy through modeling instruction

NASA Astrophysics Data System (ADS)

Sawtelle, Vashti; Brewe, Eric; Goertzen, Renee Michelle; Kramer, Laird H.

2012-02-01

In this paper we present an initial analysis connecting key elements of Modeling Instruction (MI) to self-efficacy experience opportunities. Previously, we demonstrated that MI has positive effects on self-efficacy when compared with traditional Lecture instruction [1]. We also found a particularly strong positive effect on the social persuasion source of self-efficacy for women in the MI class. Our current study seeks to understand through what mechanisms MI influences self-efficacy. We demonstrate this connection through an in-depth analysis of video chosen to exemplify Modeling techniques used in a problem-solving episode by three female participants enrolled in a MI introductory physics class. We provide a rich and descriptive analysis of the self-efficacy experiences opportunities within this context and discuss how these opportunities provide a potential explanation of how MI influences self-efficacy.

Social marketing of condoms in India.

PubMed

Thapa, S; Prasad, C V; Rao, P H; Severy, L J; Rao, S R

1994-01-01

Contraceptive social marketing is a way of supplying contraceptives to consumers who cannot afford to buy them at full market price, yet are not reached by the free public distribution program. The process involves supplying a subsidized product through existing commercial distribution networks, using the mass media and other retail marketing techniques to commercially advertise the products. India was the first country to introduce this concept to its family planning program. India's social marketing program is also the largest in the world. Over the past 25 years, total condom sales in India have expanded under the program from less than 10 million per year to more than one billion. The authors present an overview of India's social marketing initiative, describe the firms participating in the program, and summarize the lessons learned from the social marketing experience. Problems and prospects, and experiences and implications are discussed.

LDEF mechanical systems

NASA Technical Reports Server (NTRS)

Spear, W. Steve; Dursch, Harry W.

1992-01-01

Following LDEF retrieval, a number of studies were made of mechanical hardware and structure flown on the LDEF. The primary objectives are to determine the effects of long term space exposure on (1) mechanisms either used on LDEF or as part of individual experiments; (2) LDEF structural components; and (3) fasteners. Results from examination and testing of LDEF structure, fasteners, LDEF end support beam, environment exposure control canisters, experiment tray clamps, LDEF grapple fixtures, and viscous damper are presented. The most significant finding is the absence of space exposure related cold welding. The instances of seizure or removal difficulties initially attributed to cold welding were shown to have resulted from installation galling damage or improper removal techniques. Widespread difficulties encountered with removal of stainless steel fasteners underscore the need for effective thread lubrication schemes to ensure successful application of proposed orbital replacement units onboard Space Station Freedom.

Kerr Reservoir LANDSAT experiment analysis for November 1980

NASA Technical Reports Server (NTRS)

Lecroy, S. R.

1982-01-01

An experiment was conducted on the waters of Kerr Reservoir to determine if reliable algorithms could be developed that relate water quality parameters to remotely sensed data. LANDSAT radiance data was used in the analysis since it is readily available and covers the area of interest on a regular basis. By properly designing the experiment, many of the unwanted variations due to atmosphere, solar, and hydraulic changes were minimized. The algorithms developed were constrained to satisfy rigorous statistical criteria before they could be considered dependable in predicting water quality parameters. A complete mix of different types of algorithms using the LANDSAT bands was generated to provide a thorough understanding of the relationships among the data involved. The study demonstrated that for the ranges measured, the algorithms that satisfactorily represented the data are mostly linear and only require a maximum of one or two LANDSAT bands. Rationing techniques did not improve the results since the initial design of the experiment minimized the errors that this procedure is effective against. Good correlations were established for inorganic suspended solids, iron, turbidity, and secchi depth.

Measurements of Laser Imprint with High-Z Coated targets on Omega EP

NASA Astrophysics Data System (ADS)

Karasik, Max; Oh, J.; Stoeckl, C.; Aglitskiy, Y.; Schmitt, A. J.; Bates, J. W.; Obenschain, S. P.

2015-11-01

Previous experiments on Nike KrF laser (λ = 248nm) at NRL found that a thin (400-800 Å) high-Z (Au or Pd) overcoat on the laser side of the target is effective in suppressing broadband imprint and reducing ablative Richtmyer-Meshkov growth. The overcoat initially absorbs the laser and emits soft x-rays that ablate the target, forming a large stand-off distance between laser absorption and ablation and driving the target at higher mass ablation rate. Implementation of this technique on the frequency-tripled Nd:glass (351 nm) NIF would enable a wider range direct drive experiments there. To this end, we are carrying out experiments using the NIF-like beams of Omega EP. Analogous to experiments on Nike, areal mass perturbations due to RT-amplified laser imprint are measured using curved crystal imaging coupled to a streak camera. High-Z coating dynamics and target trajectory are imaged side-on. First results indicate that imprint suppression is observed, albeit with thicker coatings. Work supported by the Department of Energy/NNSA.

Automatic initialization for 3D bone registration

NASA Astrophysics Data System (ADS)

Foroughi, Pezhman; Taylor, Russell H.; Fichtinger, Gabor

2008-03-01

In image-guided bone surgery, sample points collected from the surface of the bone are registered to the preoperative CT model using well-known registration methods such as Iterative Closest Point (ICP). These techniques are generally very sensitive to the initial alignment of the datasets. Poor initialization significantly increases the chances of getting trapped local minima. In order to reduce the risk of local minima, the registration is manually initialized by locating the sample points close to the corresponding points on the CT model. In this paper, we present an automatic initialization method that aligns the sample points collected from the surface of pelvis with CT model of the pelvis. The main idea is to exploit a mean shape of pelvis created from a large number of CT scans as the prior knowledge to guide the initial alignment. The mean shape is constant for all registrations and facilitates the inclusion of application-specific information into the registration process. The CT model is first aligned with the mean shape using the bilateral symmetry of the pelvis and the similarity of multiple projections. The surface points collected using ultrasound are then aligned with the pelvis mean shape. This will, in turn, lead to initial alignment of the sample points with the CT model. The experiments using a dry pelvis and two cadavers show that the method can align the randomly dislocated datasets close enough for successful registration. The standard ICP has been used for final registration of datasets.

A technique for increasing the accuracy of the numerical inversion of the Laplace transform with applications

NASA Technical Reports Server (NTRS)

Berger, B. S.; Duangudom, S.

1973-01-01

A technique is introduced which extends the range of useful approximation of numerical inversion techniques to many cycles of an oscillatory function without requiring either the evaluation of the image function for many values of s or the computation of higher-order terms. The technique consists in reducing a given initial value problem defined over some interval into a sequence of initial value problems defined over a set of subintervals. Several numerical examples demonstrate the utility of the method.

Design and performance of the spin asymmetries of the nucleon experiment

DOE PAGES

Maxwell, J. D.; Armstrong, W. R.; Choi, S.; ...

2018-03-01

The Spin Asymmetries of the Nucleon Experiment (SANE) performed inclusive, double-polarized electron scattering measurements of the proton at the Continuous Electron Beam Facility at Jefferson Lab. A novel detector array observed scattered electrons of four-momentum transfer 2.5 < Q 2 < 6.5 GeV 2 and Bjorken scaling 0.3 < x < 0.8 from initial beam energies of 4.7 and 5.9 GeV. Employing a polarized proton target which could be rotated with respect to the incident electron beam, both parallel and near perpendicular spin asymmetries were measured, allowing model-independent access to transverse polarization observables A 1, A 2, g 1, gmore » 2 and moment d 2 of the proton. This article summarizes the operation and performance of the polarized target, polarized electron beam, and novel detector systems used during the course of the experiment, and describes analysis techniques utilized to access the physics observables of interest.« less

A small-scale experiment using microwave interferometry to investigate detonation and shock-to-detonation transition in pressed TATB

NASA Astrophysics Data System (ADS)

Renslow, Peter John

A small-scale characterization test utilizing microwave interferometry was developed to dynamically measure detonation and run to detonation distance in explosives. The technique was demonstrated by conducting two experimental series on the well-characterized explosive triaminotrinitrobenzene (TATB). In the first experiment series, the detonation velocity was observed at varying porosity. The velocity during TATB detonation matched well with predictions made using CHEETAH and an empirical relation from the Los Alamos National Laboratory (LANL). The microwave interferometer also captured unsteady propagation of the reaction when a low density charge was near the failure diameter. In the second experiment series, Pop-plots were produced using data obtained from shock initiation of the TATB through a polymethyl methacrylate (PMMA) attenuator. The results compared well to wedge test data from LANL despite the microwave interferometer test being of substantially smaller scale. The results showed the test method is attractive for rapid characterization of new and improvised explosive materials.

The PEPPo method for polarized positrons and PEPPo II

DOE PAGES

Cardman, Lawrence S.

2018-05-01

The Polarized Electrons for Polarized Positrons (PEPPo) experiment at the injector of the Continuous Electron Beam Accelerator Facility demonstrated for the first time the efficient transfer of polarization from electrons to positrons via a two-step process: polarized bremsstrahlung radiation is induced by a polarized electron beam in a high-Z target; then the polarized bremsstrahlung produces polarized positrons via the pair-production process in the same target. Positron polarization up to 82% was measured for an initial electron beam momentum of 8.19 MeV/c, limited only by the electron beam polarization of 85%. This technique extends polarized positron capabilities from GeV to MeVmore » electron beams, and opens access to polarized positron beam physics to a wide community. We present the results of the PEPPo experiment and outline tentative plans for a follow-up experiment that would investigate key aspects of an approach based on PEPPo as a polarized positron source for the 12 GeV Upgrade of CEBAF.« less

Extracorporeal membrane oxygenation: experience in an adult medical ICU.

PubMed

Hermans, G; Meersseman, W; Wilmer, A; Meyns, B; Bobbaers, H

2007-06-01

Extracorporeal membrane oxygenation (ECMO) is a technology that can provide extracorporeal gas exchange to patients with severe pulmonary or cardiac dysfunction. We report on our clinical experience with ECMO in critically ill patients. We performed a retrospective analysis of 23 patients treated with ECMO in a medical intensive care unit in a tertiary referral academic centre. 13 patients were considered immunocompetent and 10 were immunocompromised when extracorporeal membrane oxygenation was started. 16 patients presented with acute respiratory distress syndrome (ARDS), 2 patients had intractable cardiac failure, and 5 patients had combined respiratory and cardiac failure. In 16 patients, a veno-venous bypass was constructed; in 7 patients, the initial bypass was venoarterial. 11 patients survived. In 2 patients technical complications were fatal. Our data indicate that patients with community-acquired pneumonia and no underlying disease will benefit most from this technique. However, long-term survival is possible in immunocompromised patients. Venoarterial bypass can carry a higher risk for technical complications. Increasing experience apparently also reduces the risk of technical complications.

Designing Effective Persuasive Systems Utilizing the Power of Entanglement: Communication Channel, Strategy and Affect

NASA Astrophysics Data System (ADS)

Li, Haiqing; Chatterjee, Samir

With rapid advances in information and communication technology, computer-mediated communication (CMC) technologies are utilizing multiple IT platforms such as email, websites, cell-phones/PDAs, social networking sites, and gaming environments. However, no studies have compared the effectiveness of a persuasive system using such alternative channels and various persuasive techniques. Moreover, how affective computing impacts the effectiveness of persuasive systems is not clear. This study proposes (1) persuasive technology channels in combination with persuasive strategies will have different persuasive effectiveness; (2) Adding positive emotion to a message that leads to a better overall user experience could increase persuasive effectiveness. The affective computing or emotion information was added to the experiment using emoticons. The initial results of a pilot study show that computer-mediated communication channels along with various persuasive strategies can affect the persuasive effectiveness to varying degrees. These results also shows that adding a positive emoticon to a message leads to a better user experience which increases the overall persuasive effectiveness of a system.

Understanding the shock and detonation response of high explosives at the continuum and meso scales

NASA Astrophysics Data System (ADS)

Handley, C. A.; Lambourn, B. D.; Whitworth, N. J.; James, H. R.; Belfield, W. J.

2018-03-01

The shock and detonation response of high explosives has been an active research topic for more than a century. In recent years, high quality data from experiments using embedded gauges and other diagnostic techniques have inspired the development of a range of new high-fidelity computer models for explosives. The experiments and models have led to new insights, both at the continuum scale applicable to most shock and detonation experiments, and at the mesoscale relevant to hotspots and burning within explosive microstructures. This article reviews the continuum and mesoscale models, and their application to explosive phenomena, gaining insights to aid future model development and improved understanding of the physics of shock initiation and detonation propagation. In particular, it is argued that "desensitization" and the effect of porosity on high explosives can both be explained by the combined effect of thermodynamics and hydrodynamics, rather than the traditional hotspot-based explanations linked to pressure-dependent reaction rates.

Geometric Optimization for Non-Thrombogenicity of a Centrifugal Blood Pump through Flow Visualization

NASA Astrophysics Data System (ADS)

Toyoda, Masahiro; Nishida, Masahiro; Maruyama, Osamu; Yamane, Takashi; Tsutsui, Tatsuo; Sankai, Yoshiyuki

A monopivot centrifugal blood pump, whose impeller is supported with a pivot bearing and a passive magnetic bearing, is under development for implantable artificial heart. The hemolysis level is less than that of commercial centrifugal pumps and the pump size is as small as 160 mL in volume. To solve a problem of thrombus caused by fluid dynamics, flow visualization experiments and animal experiments have been undertaken. For flow visualization a three-fold scale-up model, high-speed video system, and particle tracking velocimetry software were used. To verify non-thrombogenicity one-week animal experiments were conducted with sheep. The initially observed thrombus around the pivot was removed through unifying the separate washout holes to a small centered hole to induce high shear around the pivot. It was found that the thrombus contours corresponded to the shear rate of 300s-1 for red thrombus and 1300-1700s-1 for white thrombus, respectively. Thus flow visualization technique was found to be a useful tool to predict thrombus location.

Design and performance of the spin asymmetries of the nucleon experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maxwell, J. D.; Armstrong, W. R.; Choi, S.

The Spin Asymmetries of the Nucleon Experiment (SANE) performed inclusive, double-polarized electron scattering measurements of the proton at the Continuous Electron Beam Facility at Jefferson Lab. A novel detector array observed scattered electrons of four-momentum transfer 2.5 < Q 2 < 6.5 GeV 2 and Bjorken scaling 0.3 < x < 0.8 from initial beam energies of 4.7 and 5.9 GeV. Employing a polarized proton target which could be rotated with respect to the incident electron beam, both parallel and near perpendicular spin asymmetries were measured, allowing model-independent access to transverse polarization observables A 1, A 2, g 1, gmore » 2 and moment d 2 of the proton. This article summarizes the operation and performance of the polarized target, polarized electron beam, and novel detector systems used during the course of the experiment, and describes analysis techniques utilized to access the physics observables of interest.« less

Training for percutaneous renal access on a virtual reality simulator.

PubMed

Zhang, Yi; Yu, Cheng-fan; Liu, Jin-shun; Wang, Gang; Zhu, He; Na, Yan-qun

2013-01-01

The need to develop new methods of surgical training combined with advances in computing has led to the development of virtual reality surgical simulators. The PERC Mentor(TM) is designed to train the user in percutaneous renal collecting system access puncture. This study aimed to validate the use of this kind of simulator, in percutaneous renal access training. Twenty-one urologists were enrolled as trainees to learn a fluoroscopy-guided percutaneous renal accessing technique. An assigned percutaneous renal access procedure was immediately performed on the PERC Mentor(TM) after watching instruction video and an analog operation. Objective parameters were recorded by the simulator and subjective global rating scale (GRS) score were determined. Simulation training followed and consisted of 2 hours daily training sessions for 2 consecutive days. Twenty-four hours after the training session, trainees were evaluated performing the same procedure. The post-training evaluation was compared to the evaluation of the initial attempt. During the initial attempt, none of the trainees could complete the appointed procedure due to the lack of experience in fluoroscopy-guided percutaneous renal access. After the short-term training, all trainees were able to independently complete the procedure. Of the 21 trainees, 10 had primitive experience in ultrasound-guided percutaneous nephrolithotomy. Trainees were thus categorized into the group of primitive experience and inexperience. The total operating time and amount of contrast material used were significantly lower in the group of primitive experience versus the inexperience group (P = 0.03 and 0.02, respectively). The training on the virtual reality simulator, PERC Mentor(TM), can help trainees with no previous experience of fluoroscopy-guided percutaneous renal access to complete the virtual manipulation of the procedure independently. This virtual reality simulator may become an important training and evaluation tool in teaching fluoroscopy-guided percutaneous renal access.

Advanced Undergraduate Experiments in Thermoanalytical Chemistry.

ERIC Educational Resources Information Center

Hill, J. O.; Magee, R. J.

1988-01-01

Describes several experiments using the techniques of thermal analysis and thermometric titrimetry. Defines thermal analysis and several recent branches of the technique. Notes most of the experiments use simple equipment and standard laboratory techniques. (MVL)

Critical fiber length technique for composite manufacturing processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivley, G.N.; Vandiver, T.L.; Dougherty, N.S.

1996-12-31

An improved injection technique for composite structures has been cooperatively developed by the U.S. Army Missile Command (MICOM) and Rockwell International (RI). This process simultaneously injects chopped fiberglass fibers and an epoxy resin matrix into a mold. Four injection techniques: (1){open_quotes}Little Willie{close_quotes} RTM system, (2) Pressure Vat system, (3) Pressure Vat system with vacuum assistance, and (4) Injection gun system, were investigated for use with a 304.8 mm x 304.8 mm x 5.08 mm (12 in x 12 in x 0.2 in) flat plaque mold. The driving factors in the process optimization included: fiber length, fiber weight, matrix viscosity, injectionmore » pressure, flow rate, and tool design. At fiber weights higher than 30 percent, the injection gun appears to have advantages over the other systems investigated. Results of an experimental investigation are reviewed in this paper. The investigation of injection techniques is the initial part of the research involved in a developing process, {open_quotes}Critical Fiber Length Technique{close_quotes}. This process will use the data collected in injection experiment along with mechanical properties derived from coupon test data to be incorporated into a composite material design code. The {open_quotes}Critical Fiber Length Technique{close_quotes} is part of a Cooperative Research and Development Agreement (CRADA) established in 1994 between MICOM and RI.« less

Optical Strain and Crack-Detection Measurements on a Rotating Disk

NASA Technical Reports Server (NTRS)

Woike, Mark; Abdul-Aziz, Ali; Clem, Michelle; Fralick, Gustave

2013-01-01

The development of techniques for the in-situ measurement and structural health monitoring of the rotating components in gas turbine engines is of major interest to NASA. As part of this on-going effort, several experiments have been undertaken to develop methods for detecting cracks and measuring strain on rotating turbine engine like disks. Previous methods investigated have included the use of blade tip clearance sensors to detect the presence of cracks by monitoring the change in measured blade tip clearance and analyzing the combined disk-rotor system's vibration response. More recently, an experiment utilizing a novel optical Moiré based concept has been conducted on a subscale turbine engine disk to demonstrate a potential strain measurement and crack detection technique. Moiré patterns result from the overlap of two repetitive patterns with slightly different spacing. When this technique is applied to a rotating disk, it has the potential to allow for the detection of very small changes in spacing and radial growth in a rotating disk due to a flaw such as a crack. This investigation was a continuation of previous efforts undertaken in 2011-2012 to validate this optical concept. The initial demonstration attempted on a subscale turbine engine disk was inconclusive due to the minimal radial growth experienced by the disk during operation. For the present experiment a new subscale Aluminum disk was fabricated and improvements were made to the experimental setup to better demonstrate the technique. A circular reference pattern was laser etched onto a subscale engine disk and the disk was operated at speeds up to 12 000 rpm as a means of optically monitoring the Moiré created by the shift in patterns created by the radial growth due the presence of the simulated crack. Testing was first accomplished on a clean defect free disk as a means of acquiring baseline reference data. A notch was then machined in to the disk to simulate a crack and testing was repeated for the purposes of demonstrating the concept. Displacement data was acquired using external blade tip clearance and shaft displacement sensors as a means of confirming the optical data and for validating other sensor based crack detection techniques.

Optical Strain and Crack-Detection Measurements on a Rotating Disk

NASA Technical Reports Server (NTRS)

Woike, Mark; Abdul-Aziz, Ali; Clem, Michelle M.; Fralick, Gustave

2013-01-01

The development of techniques for the in-situ measurement and structural health monitoring of the rotating components in gas turbine engines is of major interest to NASA. As part of this on-going effort, several experiments have been undertaken to develop methods for detecting cracks and measuring strain on rotating turbine engine like disks. Previous methods investigated have included the use of blade tip clearance sensors to detect the presence of cracks by monitoring the change in measured blade tip clearance and analyzing the combined disk-rotor system's vibration response. More recently, an experiment utilizing a novel optical Moiré based concept has been conducted on a subscale turbine engine disk to demonstrate a potential strain measurement and crack detection technique. Moiré patterns result from the overlap of two repetitive patterns with slightly different spacing. When this technique is applied to a rotating disk, it has the potential to allow for the detection of very small changes in spacing and radial growth in a rotating disk due to a flaw such as a crack. This investigation was a continuation of previous efforts undertaken in 2011 to 2012 to validate this optical concept. The initial demonstration attempted on a subscale turbine engine disk was inconclusive due to the minimal radial growth experienced by the disk during operation. For the present experiment a new subscale Aluminum disk was fabricated and improvements were made to the experimental setup to better demonstrate the technique. A circular reference pattern was laser etched onto a subscale engine disk and the disk was operated at speeds up to 12 000 rpm as a means of optically monitoring the Moiré created by the shift in patterns created by the radial growth due the presence of the simulated crack. Testing was first accomplished on a clean defect free disk as a means of acquiring baseline reference data. A notch was then machined in to the disk to simulate a crack and testing was repeated for the purposes of demonstrating the concept. Displacement data was acquired using external blade tip clearance and shaft displacement sensors as a means of confirming the optical data and for validating other sensor based crack detection techniques.

Damage Assessment of Aerospace Structural Components by Impedance Based Health Monitoring

NASA Technical Reports Server (NTRS)

Gyekenyesi, Andrew L.; Martin, Richard E.; Sawicki, Jerzy T.; Baaklini, George Y.

2005-01-01

This paper addresses recent efforts at the NASA Glenn Research Center at Lewis Field relating to the set-up and assessment of electro-mechanical (E/M) impedance based structural health monitoring. The overall aim is the application of the impedance based technique to aeronautic and space based structural components. As initial steps, a laboratory was created, software written, and experiments conducted on aluminum plates in undamaged and damaged states. A simulated crack, in the form of a narrow notch at various locations, was analyzed using piezoelectric-ceramic (PZT: lead, zirconate, titarate) patches as impedance measuring transducers. Descriptions of the impedance quantifying hardware and software are provided as well as experimental results. In summary, an impedance based health monitoring system was assembled and tested. The preliminary data showed that the impedance based technique was successful in recognizing the damage state of notched aluminum plates.

Approaches in the determination of plant nutrient uptake and distribution in space flight conditions

NASA Technical Reports Server (NTRS)

Heyenga, A. G.; Forsman, A.; Stodieck, L. S.; Hoehn, A.; Kliss, M.

2000-01-01

The effective growth and development of vascular plants rely on the adequate availability of water and nutrients. Inefficiency in either the initial absorption, transportation, or distribution of these elements are factors which impinge on plant structure and metabolic integrity. The potential effect of space flight and microgravity conditions on the efficiency of these processes is unclear. Limitations in the available quantity of space-grown plant material and the sensitivity of routine analytical techniques have made an evaluation of these processes impractical. However, the recent introduction of new plant cultivating methodologies supporting the application of radionuclide elements and subsequent autoradiography techniques provides a highly sensitive investigative approach amenable to space flight studies. Experiments involving the use of gel based 'nutrient packs' and the radionuclides calcium-45 and iron-59 were conducted on the Shuttle mission STS-94. Uptake rates of the radionuclides between ground and flight plant material appeared comparable.

Approaches in the Determination of Plant Nutrient Uptake and Distribution in Space Flight Conditions

NASA Technical Reports Server (NTRS)

Heyenga, A. G.; Forsman, A.; Stodieck, L. S.; Hoehn, A.; Kliss, Mark

1998-01-01

The effective growth and development of vascular plants rely on the adequate availability of water and nutrients. Inefficiency in either the initial absorption, transportation, or distribution of these elements are factors which may impinge on plant structure and metabolic integrity. The potential effect of space flight and microgravity conditions on the efficiency of these processes is unclear. Limitations in the available quantity of space-grown plant material and the sensitivity of routine analytical techniques have made an evaluation of these processes impractical. However, the recent introduction of new plant cultivating methodologies supporting the application of radionuclide elements and subsequent autoradiography techniques provides a highly sensitive investigative approach amenable to space flight studies. Experiments involving the use of gel based 'nutrient packs' and the nuclides Ca45 and Fe59 were conducted on the Shuttle mission STS-94. Uptake rates of the radionuclides between ground and flight plant material appeared comparable.

Laparoscopic access with a visualizing trocar.

PubMed

Wolf, J S

1997-01-01

Although useful in most situations, there are several inherent disadvantages of the standard laparoscopic access techniques of Veress needle insertion and Hasson-type cannula placement. Veress needle placement may be hazardous in patients at high risk for intraabdominal adhesions and difficult in patients who are obese. The usual alternative, the Hasson-type cannula, often does not provide a good gas seal. As another option, the use of a visualizing trocar (OPTIVIEW) has proven to be effective in the initial experience at the University of Michigan. The inner trocar of the visualizing trocar is hollow except for a clear plastic conical tip with two external ridges. The trocar-cannula assembly is passed through tissue layers to enter the operative space under direct vision from a 10-mm zero-degree laparoscope placed into the trocar. Results suggest that this technique is an excellent alternative to Veress needle placement when laparoscopic access is likely to be hazardous or difficult.

Cometary particulate analyzer. [mass spectrometry of laser plasmas

NASA Technical Reports Server (NTRS)

Friichtenicht, J. F.; Miller, D. J.; Utterback, N. G.

1979-01-01

A concept for determining the relative abundance of elements contained in cometary particulates was evaluated. The technique utilizes a short, high intensity burst of laser radiation to vaporize and ionize collected particulate material. Ions extracted from this laser produced plasma are analyzed in a time of flight mass spectrometer to yield an atomic mass spectrum representative of the relative abundance of elements in the particulates. Critical aspects of the development of this system are determining the ionization efficiencies for various atomic species and achieving adequate mass resolution. A technique called energy-time focus, which utilizes static electric fields to alter the length of the ion flight path in proportion to the ion initial energy, was used which results in a corresponding compression to the range of ion flight times which effectively improves the inherent resolution. Sufficient data were acquired to develop preliminary specifications for a flight experiment.

Demonstration of movement in the sacroiliac joint using ultrasound

NASA Astrophysics Data System (ADS)

Krupinski, Elizabeth A.; Brooks, William J.; Lund, Pamela J.

1995-05-01

The goal of this study was to demonstrate quantitatively, using ultrasound (US) recording techniques, the extent of motion of the sacroiliac joint achieved using manual medicine techniques. Initial judgements of perceived (i.e., felt) SI mobility during manual examination were made on 22 subjects. Baseline no movement ultrasound images (static) were obtained of the left and right SI joints at two levels-- posterior-superior-iliac-spine and inferior (PSIS, INF)--and two projections (AP and LAT). Manual medicine spring testing of the SI joint was then performed while ultrasound recordings (on video) were made. The differences between baseline separation of the SI joint and displacement distance during spring testing were measured by six radiologists who typically read US images. Significant movement of at least one SI joint was demonstrated in 91% of the subjects using ultrasound recordings. The extent of movement appeared to corroborate the experience of manual medicine practitioners.

Dynamic nuclear polarization and optimal control spatial-selective 13C MRI and MRS

NASA Astrophysics Data System (ADS)

Vinding, Mads S.; Laustsen, Christoffer; Maximov, Ivan I.; Søgaard, Lise Vejby; Ardenkjær-Larsen, Jan H.; Nielsen, Niels Chr.

2013-02-01

Aimed at 13C metabolic magnetic resonance imaging (MRI) and spectroscopy (MRS) applications, we demonstrate that dynamic nuclear polarization (DNP) may be combined with optimal control 2D spatial selection to simultaneously obtain high sensitivity and well-defined spatial restriction. This is achieved through the development of spatial-selective single-shot spiral-readout MRI and MRS experiments combined with dynamic nuclear polarization hyperpolarized [1-13C]pyruvate on a 4.7 T pre-clinical MR scanner. The method stands out from related techniques by facilitating anatomic shaped region-of-interest (ROI) single metabolite signals available for higher image resolution or single-peak spectra. The 2D spatial-selective rf pulses were designed using a novel Krotov-based optimal control approach capable of iteratively fast providing successful pulse sequences in the absence of qualified initial guesses. The technique may be important for early detection of abnormal metabolism, monitoring disease progression, and drug research.

Double-lumen balloon for Onyx® embolization via extracranial arteries in transverse sigmoid dural arteriovenous fistulas: initial experience.

PubMed

Clarençon, Frédéric; Di Maria, Federico; Gabrieli, Joseph; Carpentier, Alexandre; Pistochi, Silvia; Bartolini, Bruno; Zeghal, Chiheb; Chiras, Jacques; Sourour, Nader-Antoine

2016-10-01

Transverse-sigmoid dural arteriovenous fistulas (TS DAVFs) can be challenging to treat by endovascular means. Indeed, a total cure of the fistula can only be achieved when complete occlusion of the fistulous point(s) is obtained by penetration of the embolic agent. However, in some cases, especially for transosseous branches from extracranial arteries like the occipital artery (OcA) or the superficial temporal artery (STA), such penetration is usually poor, leading to major proximal reflux and incomplete fistula obliteration. We present three cases of embolization in two patients with TS DAVF through the OcA and/or the STA with Onyx® using a double-lumen balloon (Microvention, Tustin, CA, USA). This technique allows the penetration of the embolic agent in the transosseous branches by forming a counter-pressure with the inflated balloon. This technique may be useful to achieve complete occlusion of TS DAVFs by endovascular means.

Documentation of procedures for textural/spatial pattern recognition techniques

NASA Technical Reports Server (NTRS)

Haralick, R. M.; Bryant, W. F.

1976-01-01

A C-130 aircraft was flown over the Sam Houston National Forest on March 21, 1973 at 10,000 feet altitude to collect multispectral scanner (MSS) data. Existing textural and spatial automatic processing techniques were used to classify the MSS imagery into specified timber categories. Several classification experiments were performed on this data using features selected from the spectral bands and a textural transform band. The results indicate that (1) spatial post-processing a classified image can cut the classification error to 1/2 or 1/3 of its initial value, (2) spatial post-processing the classified image using combined spectral and textural features produces a resulting image with less error than post-processing a classified image using only spectral features and (3) classification without spatial post processing using the combined spectral textural features tends to produce about the same error rate as a classification without spatial post processing using only spectral features.

Laser welding of vas deferens in rodents: initial experience with fluid solders.

PubMed

Trickett, R I; Wang, D; Maitz, P; Lanzetta, M; Owen, E R

1998-01-01

This study evaluates the use of sutureless laser welding for vasovasostomy. In 14 rodents, the left vas deferens underwent vasovasostomy using an albumin-based solder applied to the adventitia of the vas deferens. The solder contained the dye, indocyanine green, to allow selective absorption and denaturation by a fiber-coupled 800-nm diode laser. The right vas deferens served as a control, receiving conventional layered microsurgical repair. We used a removable 4/0 nylon stent and microclamps to appose the vas deferens during repair, with no need for stay sutures. The mean time to perform laser solder repair (23.5 min) and conventional repair (23.3 min) were not significantly different (P=0.91). However, examination after 8 weeks showed that granuloma formation (G) and patency (P) rates for the conventional suture technique (G, 14%; P, 93%) were significantly better than observed for the laser solder technique (G, 57%; P, 50%).

Study of thermite mixtures consolidated by cold gas dynamic spray process

NASA Astrophysics Data System (ADS)

Bacciochini, Antoine; Maines, Geoffrey; Poupart, Christian; Radulescu, Matei; Jodoin, Bertrand; Lee, Julian

2013-06-01

The present study focused on the cold gas dynamic spray process for manufacturing finely structured energetic materials with high reactivity, vanishing porosity, as well as structural integrity and arbitrary shape. The experiments have focused the reaction between the aluminum and metal oxides, such as Al-CuO and Al-MoO3 systems. To increase the reactivity, an initial mechanical activation was achieved through interrupted ball milling. The consolidation of the materials used the supersonic cold gas spray technique, where the particles are accelerated to high speeds and consolidated via plastic deformation upon impact, forming activated nano-composites in arbitrary shapes with close to zero porosity. This technique permits to retain the feedstock powder micro-structure and prevents any reactions during the consolidation phase. Reactivity of mixtures has been investigated through flame propagation analysis on cold sprayed samples and compacted powder mixture. Deflagration tests showed the influence of porosity on the reactivity.

Theory, simulation and experiments for precise deflection control of radiotherapy electron beams.

PubMed

Figueroa, R; Leiva, J; Moncada, R; Rojas, L; Santibáñez, M; Valente, M; Velásquez, J; Young, H; Zelada, G; Yáñez, R; Guillen, Y

2018-03-08

Conventional radiotherapy is mainly applied by linear accelerators. Although linear accelerators provide dual (electron/photon) radiation beam modalities, both of them are intrinsically produced by a megavoltage electron current. Modern radiotherapy treatment techniques are based on suitable devices inserted or attached to conventional linear accelerators. Thus, precise control of delivered beam becomes a main key issue. This work presents an integral description of electron beam deflection control as required for novel radiotherapy technique based on convergent photon beam production. Theoretical and Monte Carlo approaches were initially used for designing and optimizing device´s components. Then, dedicated instrumentation was developed for experimental verification of electron beam deflection due to the designed magnets. Both Monte Carlo simulations and experimental results support the reliability of electrodynamics models used to predict megavoltage electron beam control. Copyright © 2018 Elsevier Ltd. All rights reserved.

Prediction and Optimization of Key Performance Indicators in the Production of Stator Core Using a GA-NN Approach

NASA Astrophysics Data System (ADS)

Rajora, M.; Zou, P.; Xu, W.; Jin, L.; Chen, W.; Liang, S. Y.

2017-12-01

With the rapidly changing demands of the manufacturing market, intelligent techniques are being used to solve engineering problems due to their ability to handle nonlinear complex problems. For example, in the conventional production of stator cores, it is relied upon experienced engineers to make an initial plan on the number of compensation sheets to be added to achieve uniform pressure distribution throughout the laminations. Additionally, these engineers must use their experience to revise the initial plans based upon the measurements made during the production of stator core. However, this method yields inconsistent results as humans are incapable of storing and analysing large amounts of data. In this article, first, a Neural Network (NN), trained using a hybrid Levenberg-Marquardt (LM) - Genetic Algorithm (GA), is developed to assist the engineers with the decision-making process. Next, the trained NN is used as a fitness function in an optimization algorithm to find the optimal values of the initial compensation sheet plan with the aim of minimizing the required revisions during the production of the stator core.

Initial photoinduced dynamics of the photoactive yellow protein.

PubMed

Larsen, Delmar S; van Grondelle, Rienk

2005-05-01

The photoactive yellow protein (PYP) is the photoreceptor protein responsible for initiating the blue-light repellent response of the Halorhodospira halophila bacterium. Optical excitation of the intrinsic chromophore in PYP, p-coumaric acid, leads to the initiation of a photocycle that comprises several distinct intermediates. The dynamical processes responsible for the initiation of the PYP photocycle have been explored with several time-resolved techniques, which include ultrafast electronic and vibrational spectroscopies. Ultrafast electronic spectroscopies, such as pump-visible probe, pump-dump-visible probe, and fluorescence upconversion, are useful in identifying the timescales and connectivity of the transient intermediates, while ultrafast vibrational spectroscopies link these intermediates to dynamic structures. Herein, we present the use of these techniques for exploring the initial dynamics of PYP, and show how these techniques provide the basis for understanding the complex relationship between protein and chromophore, which ultimately results in biological function.

Identifying asteroid families >2 Gyrs-old

NASA Astrophysics Data System (ADS)

Bolin, Bryce T.; Morbidelli, Alessandro; Delbo, Marco; Walsh, Kevin J.

2017-10-01

There are only a few known Main Belt (MB) asteroid families with ages >2 Gyr. The lack of ancient families may be due to a bias in current techniques used to identify families. Ancient asteroid family fragments disperse in their orbital elements (a,e,i), due to secular resonances and the Yarkovsky effect (YE) making them difficult to identify. We have developed a new technique that is insensitive to the resonant spreading of fragments in e and i by searching for V-shaped correlations between family members in a vs 1/Diameter space. Our V-shape technique is demonstrated on known families and used to discover a 4 Gyr-old family linking most dark asteroids in the inner MB previously not included in any known family. In addition, the 4 Gyr-old family reveals asteroids with D >35 km that are do not belong to any asteroid family implying that they originally accreted from the protoplanetary disk.The V-shape detection tool is also a powerful analysis tool by finding the boundary of an asteroid family and fitting for its shape. Following the proposed relationship between thermal inertia (TI) with D, we find that asteroids YE drift rate might have a more complex size dependence than previous thought, leading to a curved family boundary in a vs 1/D space. The V-shape tool is capable of detecting this on synthetic families and was deployed on >30 families located throughout the MB to find this effect and quantify the YE size-dependent drift rate. We find that there is no correlation between family age and V-shape curvature. In addition, the V-shape curvature decreases for asteroid families with larger a suggesting that the relationship between TI and D is weaker in the outer MB.By examining families <20 Myrs-old, we can use this tool to separate family shape that is due to the initial ejection velocity and that which is due to the YE drift rate. V-shapes which do not contain any spreading due to YE preserve their initial ejection velocity. We constrain the initial initial velocity of young families by measuring the curvature of their fragments' V-shape in a vs 1/D space. We find that the majority of <20 Myr-old asteroid families have initial velocity fields scaling with 1/D supporting impact experiments.

Initial Experience With a New Mitral Ring Designed to Simplify Length Determination of Neochords.

PubMed

Prinzing, Anatol; Bleiziffer, Sabine; Krane, Markus; Lange, Ruediger

2018-06-01

Artificial chord implantation has become one of the most applied techniques for mitral valve repair (MVR). Many techniques have been described, with the goal of optimizing neochord implantation. A new annuloplasty device designed to simplify the determination of the appropriate neochord length has been recently introduced. We describe our initial experience with this new device. The semirigid device is equipped with removable loops on the posterior aspect of the ring. Neochords are tied to the loops, which are subsequently removed. The device was implanted in 47 symptomatic patients from January 2015 to August 2016 through a median sternotomy in 33 patients (70.2%) and a right anterolateral minithoracotomy in 14 (29.8%). The cause of mitral valve insufficiency was degenerative in all patients, and most patients presented with isolated prolapse of the posterior leaflet. Before and after cardiopulmonary bypass, all patients underwent evaluation with transesophageal echocardiography, and transthoracic echocardiography was performed at discharge. A median of 2 neochords were implanted (minimum, 1; maximum, 6). Mean cardiopulmonary bypass time and aortic cross-clamp times were 141.7 ± 32.3 and 104.8 ± 28.5 minutes for combined and 133 ± 53.9 and 98.3 ± 41.6 minutes for isolated MVR. At discharge, echocardiography revealed no or only mild mitral insufficiency in 45 patients (mean gradient, 2.9 ± 1.3 mm Hg). This new annuloplasty ring facilitated determination of appropriate neochord length and was used to successfully treat different degenerative pathologies affecting both leaflets. This new device simplified length determination of the neochords. Copyright © 2018 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Robotic-assisted laparoscopic partial nephrectomy: initial experience in Brazil and a review of the literature.

PubMed

Passerotti, Carlo Camargo; Pessoa, Rodrigo; da Cruz, Jose Arnaldo Shiomi; Okano, Marcelo Takeo; Antunes, Alberto Azoubel; Nesrallah, Adriano Joao; Dall'oglio, Marcos Francisco; Andrade, Enrico; Srougi, Miguel

2012-01-01

Partial nephrectomy has become the standard of care for renal tumors less than 4 cm in diameter. Controversy still exists, however, regarding the best surgical approach, especially when minimally invasive techniques are taken into account. Robotic-assisted laparoscopic partial nephrectomy (RALPN) has emerged as a promising technique that helps surgeons achieve the standards of open partial nephrectomy care while offering a minimally invasive approach. The objective of the present study was to describe our initial experience with robotic-assisted laparoscopic partial nephrectomy and extensively review the pertinent literature. Between August 2009 and February 2010, eight consecutive selected patients with contrast enhancing renal masses observed by CT were submitted to RALPN in a private institution. In addition, we collected information on the patients ' demographics, preoperative tumor characteristics and detailed operative, postoperative and pathological data. In addition, a PubMed search was performed to provide an extensive review of the robotic-assisted laparoscopic partial nephrectomy literature. Seven patients had RALPN on the left or right sides with no intraoperative complications. One patient was electively converted to a robotic-assisted radical nephrectomy. The operative time ranged from 120 to 300 min, estimated blood loss (EBL) ranged from 75 to 400 mL and, in five cases, the warm ischemia time (WIT) ranged from 18 to 32 min. Two patients did not require any clamping. Overall, no transfusions were necessary, and there were no intraoperative complications or adverse postoperative clinical events. All margins were negative, and all patients were disease-free at the 6-month follow-up. Robotic-assisted laparoscopic partial nephrectomy is a feasible and safe approach to small renal cortical masses. Further prospective studies are needed to compare open partial nephrectomy with its minimally invasive counterparts.

Differential Drag Demonstration: A Post-Mission Experiment with the EO-1 Spacecraft

NASA Technical Reports Server (NTRS)

Hull, Scott; Shelton, Amanda; Richardson, David

2017-01-01

Differential drag is a technique for altering the semi-major axis, velocity, and along-track position of a spacecraft in low Earth orbit. It involves varying the spacecrafts cross-sectional area relative to its velocity direction by temporarily changing attitude and solar array angles, thus varying the amount of atmospheric drag on the spacecraft. The technique has recently been proposed and used by at least three satellite systems for initial separation of constellation spacecraft after launch, stationkeeping during the mission, and potentially for conjunction avoidance. Similarly, differential drag has been proposed as a control strategy for rendezvous, removing the need for active propulsion. In theory, some operational missions that lack propulsion capability could use this approach for conjunction avoidance, though options are typically constrained for spacecraft that are already in orbit. Shortly before the spacecraft was decommissioned, an experiment was performed using NASAs EO-1 spacecraft in order to demonstrate differential drag on an operational spacecraft in orbit, and discover some of the effects differential drag might manifest. EO-1 was not designed to maintain off-nominal orientations for long periods, and as a result the team experienced unanticipated challenges during the experiment. This paper will discuss operations limitations identified before the experiment, as well as those discovered during the experiment. The effective displacement that resulted from increasing the drag area for 39 hours will be compared to predictions as well as the expected position if the spacecraft maintained nominal operations. A hypothetical scenario will also be examined, studying the relative risks of maintaining an operational spacecraft bus in order to maintain the near-maximum drag area orientation and hasten reentry.

i3Drefine software for protein 3D structure refinement and its assessment in CASP10.

PubMed

Bhattacharya, Debswapna; Cheng, Jianlin

2013-01-01

Protein structure refinement refers to the process of improving the qualities of protein structures during structure modeling processes to bring them closer to their native states. Structure refinement has been drawing increasing attention in the community-wide Critical Assessment of techniques for Protein Structure prediction (CASP) experiments since its addition in 8(th) CASP experiment. During the 9(th) and recently concluded 10(th) CASP experiments, a consistent growth in number of refinement targets and participating groups has been witnessed. Yet, protein structure refinement still remains a largely unsolved problem with majority of participating groups in CASP refinement category failed to consistently improve the quality of structures issued for refinement. In order to alleviate this need, we developed a completely automated and computationally efficient protein 3D structure refinement method, i3Drefine, based on an iterative and highly convergent energy minimization algorithm with a powerful all-atom composite physics and knowledge-based force fields and hydrogen bonding (HB) network optimization technique. In the recent community-wide blind experiment, CASP10, i3Drefine (as 'MULTICOM-CONSTRUCT') was ranked as the best method in the server section as per the official assessment of CASP10 experiment. Here we provide the community with free access to i3Drefine software and systematically analyse the performance of i3Drefine in strict blind mode on the refinement targets issued in CASP10 refinement category and compare with other state-of-the-art refinement methods participating in CASP10. Our analysis demonstrates that i3Drefine is only fully-automated server participating in CASP10 exhibiting consistent improvement over the initial structures in both global and local structural quality metrics. Executable version of i3Drefine is freely available at http://protein.rnet.missouri.edu/i3drefine/.

Differential Drag Demonstration: A Post-Mission Experiment with the EO-1 Spacecraft

NASA Technical Reports Server (NTRS)

Hull, Scott; Shelton, Amanda; Richardson, David

2017-01-01

Differential drag is a technique for altering the semimajor axis, velocity, and along-track position of a spacecraft in low Earth orbit. It involves varying the spacecraft's cross-sectional area relative to its velocity direction by temporarily changing attitude and solar array angles, thus varying the amount of atmospheric drag on the spacecraft. The technique has recently been proposed and used by at least three satellite systems for initial separation of constellation spacecraft after launch, stationkeeping during the mission, and potentially for conjunction avoidance. Similarly, differential drag has been proposed as a control strategy for rendezvous, removing the need for active propulsion. In theory, some operational missions that lack propulsion capability could use this approach for conjunction avoidance, though options are typically constrained for spacecraft that are already in orbit. Shortly before the spacecraft was decommissioned, an experiment was performed using NASA's EO-1 spacecraft in order to demonstrate differential drag on an operational spacecraft in orbit, and discover some of the effects differential drag might manifest. EO-1 was not designed to maintain off-nominal orientations for long periods, and as a result the team experienced unanticipated challenges during the experiment. This paper will discuss operations limitations identified before the experiment, as well as those discovered during the experiment. The effective displacement that resulted from increasing the drag area for 39 hours will be compared to predictions as well as the expected position if the spacecraft maintained nominal operations. A hypothetical scenario will also be examined, studying the relative risks of maintaining an operational spacecraft bus in order to maintain the near-maximum drag area orientation and hasten reentry.

Application of Self Nulling Eddy Current Probe Technique to the Detection of Fatigue Crack Initiation and Control of Test Procedures

NASA Technical Reports Server (NTRS)

Namkung, M.; Nath, S.; Wincheski, B.; Fulton, J. P.

1994-01-01

A major part of fracture mechanics is concerned with studying the initiation and propagation of fatigue cracks. This typically requires constant monitoring of crack growth during fatigue cycles and the knowledge of the precise location of the crack tip at any given time. One technique currently available for measuring fatigue crack length is the Potential Drop method. The method, however, may be inaccurate if the direction of crack growth deviates considerably from what was assumed initially or the curvature of the crack becomes significant. Another popular approach is to optically view the crack using a high magnification microscope, but this entails a person constantly monitoring it. The present proposed technique uses an automated scheme, in order to eliminate the need for a person to constantly monitor the experiment. Another technique under development elsewhere is to digitize an optical image of the test specimen surface and then apply a pattern recognition algorithm to locate the crack tip. A previous publication showed that the self nulling eddy current probe successfully tracked a simulated crack in an aluminum sample. This was the impetus to develop an online real time crack monitoring system. An automated system has been developed which includes a two axis scanner mounted on the tensile testing machine, the probe and its instrumentation and a personal computer (PC) to communicate and control all the parameters. The system software controls the testing parameters as well as monitoring the fatigue crack as it propagates. This paper will discuss the experimental setup in detail and demonstrate its capabilities. A three dimensional finite element model is utilized to model the magnetic field distribution due to the probe and how the probe voltage changes as it scans the crack. Experimental data of the probe for different samples under zero load, static load and high cycle fatigue load will be discussed. The final section summarizes the major accomplishments of the present work, the elements of the future R&D needs and the advantages and disadvantages of using this system in the laboratory and field.

Southeast Regional Experiment Station

NASA Astrophysics Data System (ADS)

1994-08-01

This is the final report of the Southeast Regional Experiment Station project. The Florida Solar Energy Center (FSEC), a research institute of the University of Central Florida (UCF), has operated the Southeast Regional Experiment Station (SE RES) for the US Department of Energy (DOE) since September 1982. Sandia National Laboratories, Albuquerque (SNLA) provides technical program direction for both the SE RES and the Southwest Regional Experiment Station (SW RES) located at the Southwest Technology Development Institute at Las Cruces, New Mexico. This cooperative effort serves a critical role in the national photovoltaic program by conducting system evaluations, design assistance and technology transfer to enhance the cost-effective utilization and development of photovoltaic technology. Initially, the research focus of the SE RES program centered on utility-connected PV systems and associated issues. In 1987, the SE RES began evaluating amorphous silicon (a-Si) thin-film PV modules for application in utility-interactive systems. Stand-alone PV systems began receiving increased emphasis at the SE RES in 1986. Research projects were initiated that involved evaluation of vaccine refrigeration, water pumping and other stand-alone power systems. The results of this work have led to design optimization techniques and procedures for the sizing and modeling of PV water pumping systems. Later recent research at the SE RES included test and evaluation of batteries and charge controllers for stand-alone PV system applications. The SE RES project provided the foundation on which FSEC achieved national recognition for its expertise in PV systems research and related technology transfer programs. These synergistic products of the SE RES illustrate the high visibility and contributions the FSEC PV program offers to the DOE.

ISPyB: an information management system for synchrotron macromolecular crystallography.

PubMed

Delagenière, Solange; Brenchereau, Patrice; Launer, Ludovic; Ashton, Alun W; Leal, Ricardo; Veyrier, Stéphanie; Gabadinho, José; Gordon, Elspeth J; Jones, Samuel D; Levik, Karl Erik; McSweeney, Seán M; Monaco, Stéphanie; Nanao, Max; Spruce, Darren; Svensson, Olof; Walsh, Martin A; Leonard, Gordon A

2011-11-15

Individual research groups now analyze thousands of samples per year at synchrotron macromolecular crystallography (MX) resources. The efficient management of experimental data is thus essential if the best possible experiments are to be performed and the best possible data used in downstream processes in structure determination pipelines. Information System for Protein crystallography Beamlines (ISPyB), a Laboratory Information Management System (LIMS) with an underlying data model allowing for the integration of analyses down-stream of the data collection experiment was developed to facilitate such data management. ISPyB is now a multisite, generic LIMS for synchrotron-based MX experiments. Its initial functionality has been enhanced to include improved sample tracking and reporting of experimental protocols, the direct ranking of the diffraction characteristics of individual samples and the archiving of raw data and results from ancillary experiments and post-experiment data processing protocols. This latter feature paves the way for ISPyB to play a central role in future macromolecular structure solution pipelines and validates the application of the approach used in ISPyB to other experimental techniques, such as biological solution Small Angle X-ray Scattering and spectroscopy, which have similar sample tracking and data handling requirements.

What I make up when I wake up: anti-experience views and narrative fabrication of dreams.

PubMed

Rosen, Melanie G

2013-01-01

I propose a narrative fabrication thesis of dream reports, according to which dream reports are often not accurate representations of experiences that occur during sleep. I begin with an overview of anti-experience theses of Norman Malcolm and Daniel Dennett who reject the received view of dreams, that dreams are experiences we have during sleep which are reported upon waking. Although rejection of the first claim of the received view, that dreams are experiences that occur during sleep, is implausible, I evaluate in more detail the second assumption of the received view, that dream reports are generally accurate. I then propose a "narrative fabrication" view of dreams as an alternative to the received view. Dream reports are often confabulated or fabricated because of poor memory, bizarre dream content, and cognitive deficits. It is well documented that narratives can be altered between initial rapid eye movement sleep awakenings and subsequent reports. I argue that we have reason to suspect that initial reports are prone to inaccuracy. Experiments demonstrate that subjects rationalize strange elements in narratives, leaving out supernatural or bizarre components when reporting waking memories of stories. Inaccuracies in dream reports are exacerbated by rapid memory loss and bizarre dream content. Waking memory is a process of reconstruction and blending of elements, but unlike waking memory, we cannot reality-test for dream memories. Dream experiences involve imaginative elements, and dream content cannot be verified with external evidence. Some dreams may involve wake-like higher cognitive functions, such as lucid dreams. Such dreams are more likely to elicit accurate reports than cognitively deficient dreams. However, dream reports are generally less accurate than waking reports. I then propose methods which could verify the narrative fabrication view, and argue that although the theory cannot be tested with current methods, new techniques and technologies may be able to do so in the future.

What I make up when I wake up: anti-experience views and narrative fabrication of dreams

PubMed Central

Rosen, Melanie G.

2013-01-01

I propose a narrative fabrication thesis of dream reports, according to which dream reports are often not accurate representations of experiences that occur during sleep. I begin with an overview of anti-experience theses of Norman Malcolm and Daniel Dennett who reject the received view of dreams, that dreams are experiences we have during sleep which are reported upon waking. Although rejection of the first claim of the received view, that dreams are experiences that occur during sleep, is implausible, I evaluate in more detail the second assumption of the received view, that dream reports are generally accurate. I then propose a “narrative fabrication” view of dreams as an alternative to the received view. Dream reports are often confabulated or fabricated because of poor memory, bizarre dream content, and cognitive deficits. It is well documented that narratives can be altered between initial rapid eye movement sleep awakenings and subsequent reports. I argue that we have reason to suspect that initial reports are prone to inaccuracy. Experiments demonstrate that subjects rationalize strange elements in narratives, leaving out supernatural or bizarre components when reporting waking memories of stories. Inaccuracies in dream reports are exacerbated by rapid memory loss and bizarre dream content. Waking memory is a process of reconstruction and blending of elements, but unlike waking memory, we cannot reality-test for dream memories. Dream experiences involve imaginative elements, and dream content cannot be verified with external evidence. Some dreams may involve wake-like higher cognitive functions, such as lucid dreams. Such dreams are more likely to elicit accurate reports than cognitively deficient dreams. However, dream reports are generally less accurate than waking reports. I then propose methods which could verify the narrative fabrication view, and argue that although the theory cannot be tested with current methods, new techniques and technologies may be able to do so in the future. PMID:23964260

Variables Affecting Pharmacy Students’ Patient Care Interventions during Advanced Pharmacy Practice Experiences

PubMed Central

Patterson, Brandon J.; Sen, Sanchita; Bingham, Angela L.; Bowen, Jane F.; Ereshefsky, Benjamin; Siemianowski, Laura A.

2016-01-01

Objective. To identify the temporal effect and factors associated with student pharmacist self-initiation of interventions during acute patient care advanced pharmacy practice experiences (APPE). Methods. During the APPE, student pharmacists at an academic medical center recorded their therapeutic interventions and who initiated the intervention throughout clinical rotations. At the end of the APPE student pharmacists completed a demographic survey. Results. Sixty-two student pharmacists were included. Factors associated with lower rates of self-initiated interventions were infectious diseases and pediatrics APPEs and an intention to pursue a postgraduate residency. Timing of the APPE, previous specialty elective course completion, and previous hospital experience did not result in any significant difference in self-initiated recommendations. Conclusion. Preceptors should not base practice experience expectations for self-initiated interventions on previous student experience or future intentions. Additionally, factors leading to lower rates of self-initiated interventions on infectious diseases or pediatrics APPEs should be explored. PMID:27756924

Per-oral endoscopic myotomy for achalasia: An American perspective

PubMed Central

Friedel, David; Modayil, Rani; Iqbal, Shahzad; Grendell, James H; Stavropoulos, Stavros N

2013-01-01

Achalasia is an uncommon esophageal motility disorder characterized by the selective loss of enteric neurons leading to absence of peristalsis and impaired relaxation of the lower esophageal sphincter. Per-oral endoscopic myotomy (POEM) is a novel modality for the treatment of achalasia performed by gastroenterologists and surgeons. It represents a natural orifice transluminal endoscopic surgery (NOTES) approach to Heller myotomy. POEM has the minimal invasiveness of an endoscopic procedure that can duplicate results of the surgical Heller myotomy. POEM is conceptually similar to a surgical myotomy without the inherent external incisions and post-operative care associated with surgery. Initial high success and low complications rates promise a great future for this technique. In fact, POEM has been successfully performed on patients with end-stage achalasia as an initial treatment reserving esophagectomy for those without good response. The volume of POEMs performed worldwide has grown exponentially. In fact, surgeons who have performed Heller myotomy have embraced POEM as the preferred intervention for achalasia. However, the niche of POEM remains to be defined and long term results are awaited. We describe our experience with POEM having performed the first POEM outside of Japan in 2009, the evolution of our technique, and give our perspective on its future. PMID:24044040

Perk Station – Percutaneous Surgery Training and Performance Measurement Platform

PubMed Central

Vikal, Siddharth; U-Thainual, Paweena; Carrino, John A.; Iordachita, Iulian; Fischer, Gregory S.; Fichtinger, Gabor

2009-01-01

Motivation Image-guided percutaneous (through the skin) needle-based surgery has become part of routine clinical practice in performing procedures such as biopsies, injections and therapeutic implants. A novice physician typically performs needle interventions under the supervision of a senior physician; a slow and inherently subjective training process that lacks objective, quantitative assessment of the surgical skill and performance[S1]. Shortening the learning curve and increasing procedural consistency are important factors in assuring high-quality medical care. Methods This paper describes a laboratory validation system, called Perk Station, for standardized training and performance measurement under different assistance techniques for needle-based surgical guidance systems. The initial goal of the Perk Station is to assess and compare different techniques: 2D image overlay, biplane laser guide, laser protractor and conventional freehand. The main focus of this manuscript is the planning and guidance software system developed on the 3D Slicer platform, a free, open source software package designed for visualization and analysis of medical image data. Results The prototype Perk Station has been successfully developed, the associated needle insertion phantoms were built, and the graphical user interface was fully implemented. The system was inaugurated in undergraduate teaching and a wide array of outreach activities. Initial results, experiences, ongoing activities and future plans are reported. PMID:19539446

Combination of novel coalescing oil water separator and electrocoagulation technique for treatment of petroleum compound contaminated groundwater.

PubMed

Oladzad, Sepideh; Fallah, Narges; Nasernejad, Bahram

2017-07-01

In the present study a combination of a novel coalescing oil water separator (COWS) and electrocoagulation (EC) technique was used for treatment of petroleum product contaminated groundwater. In the first phase, COWS was used as the primary treatment. Two different types of coalescing media and two levels of flow rates were examined in order to find the optimum conditions. The effluent of COWS was collected in optimum conditions and was treated using an EC process in the second phase of the research. In this phase, preliminary experiments were conducted in order to investigate the effect of EC reaction time and sedimentation time on chemical oxygen demand (COD) removal efficiency. Best conditions for EC reaction time and sedimentation time were obtained to be 5 min and 30 min, respectively. Response surface methodology was applied to evaluate the effect of initial pH, current density and aeration rate on settling velocity (V s ) and effluent COD. The optimum conditions, for achieving maximum values of V s as well as the values of effluent COD, in the range of results were obtained at conditions of 7, 34 mA·cm -2 and 1.5 L·min -1 for initial pH, current density and aeration rate, respectively.

Image Based Hair Segmentation Algorithm for the Application of Automatic Facial Caricature Synthesis

PubMed Central

Peng, Zhenyun; Zhang, Yaohui

2014-01-01

Hair is a salient feature in human face region and are one of the important cues for face analysis. Accurate detection and presentation of hair region is one of the key components for automatic synthesis of human facial caricature. In this paper, an automatic hair detection algorithm for the application of automatic synthesis of facial caricature based on a single image is proposed. Firstly, hair regions in training images are labeled manually and then the hair position prior distributions and hair color likelihood distribution function are estimated from these labels efficiently. Secondly, the energy function of the test image is constructed according to the estimated prior distributions of hair location and hair color likelihood. This energy function is further optimized according to graph cuts technique and initial hair region is obtained. Finally, K-means algorithm and image postprocessing techniques are applied to the initial hair region so that the final hair region can be segmented precisely. Experimental results show that the average processing time for each image is about 280 ms and the average hair region detection accuracy is above 90%. The proposed algorithm is applied to a facial caricature synthesis system. Experiments proved that with our proposed hair segmentation algorithm the facial caricatures are vivid and satisfying. PMID:24592182

Non-Solenoidal Tokamak Startup via Inboard Local Helicity Injection on the Pegasus ST

NASA Astrophysics Data System (ADS)

Perry, J. M.; Barr, J. L.; Bodner, G. M.; Bongard, M. W.; Fonck, R. J.; Pachicano, J. L.; Reusch, J. A.; Rodriguez Sanchez, C.; Richner, N. J.; Schlossberg, D. J.

2016-10-01

Local helicity injection (LHI) is a non-solenoidal startup technique utilizing small injectors at the plasma edge to source current along helical magnetic field lines. Unstable injected current streams relax to a tokamak-like configuration with high toroidal current multiplication. Flexible placement of injectors permits tradeoffs between helicity injection rate, poloidal field induction, and magnetic geometry requirements for initial relaxation. Experiments using a new set of large-area injectors in the lower divertor explore the efficacy of high-field-side (HFS) injection. The increased area (4 cm2) current source is functional up to full Pegasus toroidal field (BT , inj = 0.23 T). However, relaxation to a tokamak state is increasingly frustrated for BT , inj > 0.15 T with uniform vacuum vertical field. Paths to relaxation at increased field include: manipulation of vacuum poloidal field geometry; increased injector current; and plasma initiation with outboard injectors, subsequently transitioning to divertor injector drive. During initial tests of HFS injectors, achieved Vinj was limited to 600 V by plasma-material interactions on the divertor plate, which may be mitigated by increasing injector elevation. In experiments with helicity injection as the dominant current drive Ip 0.13 MA has been attained, with T̲e > 100 eV and ne 1019 m-3. Extrapolation to full BT, longer pulse length, and Vinj 1 kV suggest Ip > 0.25 MA should be attainable in a plasma dominated by helicity drive. Work supported by US DOE Grant DE-FG02-96ER54375.

Experimental and numerical study on bubble-sphere interaction near a rigid wall

NASA Astrophysics Data System (ADS)

Li, S.; Zhang, A. M.; Han, R.; Liu, Y. Q.

2017-09-01

This study is concerned with the interaction between a violently oscillating bubble and a movable sphere with comparable size near a rigid wall, which is an essential physical phenomenon in many applications such as cavitation, underwater explosion, ultrasonic cleaning, and biomedical treatment. Experiments are performed in a cubic water tank, and the underwater electric discharge technique (580 V DC) is employed to generate a bubble that is initiated between a rigid wall and a sphere in an axisymmetric configuration. The bubble-sphere interactions are captured using a high-speed camera operating at 52 000 frames/s. A classification of the bubble-sphere interaction is proposed, i.e., "weak," "intermediate," and "strong" interactions, identified with three distinct bubble shapes at the maximum volume moment. In the numerical simulations, the boundary integral method and the auxiliary function method are combined to establish a full coupling model that decouples the mutual dependence between the force and the sphere motion. The main features of bubble dynamics in different experiments are well reproduced by our numerical model. Meanwhile, the pressure and velocity fields are also provided for clarifying the associated mechanisms. The effects of two dimensionless standoff parameters, namely, γs (defined as ds/Rm, where ds is the minimum distance between the initial bubble center and the sphere surface and Rm is the maximum bubble radius) and γw (defined as dw/Rm, where dw is the distance between the initial bubble center and the rigid wall), are also discussed.

Impact of Standardized Communication Techniques on Errors during Simulated Neonatal Resuscitation.

PubMed

Yamada, Nicole K; Fuerch, Janene H; Halamek, Louis P

2016-03-01

Current patterns of communication in high-risk clinical situations, such as resuscitation, are imprecise and prone to error. We hypothesized that the use of standardized communication techniques would decrease the errors committed by resuscitation teams during neonatal resuscitation. In a prospective, single-blinded, matched pairs design with block randomization, 13 subjects performed as a lead resuscitator in two simulated complex neonatal resuscitations. Two nurses assisted each subject during the simulated resuscitation scenarios. In one scenario, the nurses used nonstandard communication; in the other, they used standardized communication techniques. The performance of the subjects was scored to determine errors committed (defined relative to the Neonatal Resuscitation Program algorithm), time to initiation of positive pressure ventilation (PPV), and time to initiation of chest compressions (CC). In scenarios in which subjects were exposed to standardized communication techniques, there was a trend toward decreased error rate, time to initiation of PPV, and time to initiation of CC. While not statistically significant, there was a 1.7-second improvement in time to initiation of PPV and a 7.9-second improvement in time to initiation of CC. Should these improvements in human performance be replicated in the care of real newborn infants, they could improve patient outcomes and enhance patient safety. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Characterizing and Modulating Brain Circuitry through Transcranial Magnetic Stimulation Combined with Electroencephalography.

PubMed

Farzan, Faranak; Vernet, Marine; Shafi, Mouhsin M D; Rotenberg, Alexander; Daskalakis, Zafiris J; Pascual-Leone, Alvaro

2016-01-01

The concurrent combination of transcranial magnetic stimulation (TMS) with electroencephalography (TMS-EEG) is a powerful technology for characterizing and modulating brain networks across developmental, behavioral, and disease states. Given the global initiatives in mapping the human brain, recognition of the utility of this technique is growing across neuroscience disciplines. Importantly, TMS-EEG offers translational biomarkers that can be applied in health and disease, across the lifespan, and in humans and animals, bridging the gap between animal models and human studies. However, to utilize the full potential of TMS-EEG methodology, standardization of TMS-EEG study protocols is needed. In this article, we review the principles of TMS-EEG methodology, factors impacting TMS-EEG outcome measures, and the techniques for preventing and correcting artifacts in TMS-EEG data. To promote the standardization of this technique, we provide comprehensive guides for designing TMS-EEG studies and conducting TMS-EEG experiments. We conclude by reviewing the application of TMS-EEG in basic, cognitive and clinical neurosciences, and evaluate the potential of this emerging technology in brain research.

Extended maxillotomy for skull base access in contemporary management of chordomas: Rationale and technical aspect.

PubMed

Abdul Jalil, Muhammad Fahmi; Story, Rowan D; Rogers, Myron

2017-05-01

Minimally invasive approaches to the central skull base have been popularized over the last decade and have to a large extent displaced 'open' procedures. However, traditional skull base surgery still has its role especially when dealing with a large clival chordoma where maximal surgical resection is the principal goal to maximize patient survival. In this paper, we present a case of a 25year-old male patient with chordoma in the inferior clivus which was initially debulked via a transnasal endoscopic approach. He unfortunately had a large recurrence of tumor requiring re-do resection. With the aim to achieve maximal surgical resection, we then chose the technique of a transoral approach with Le Fort 1 maxillotomy and midline palatal split. Post-operative course for the patient was uneventful and post-operative MRI confirmed significant debulking of the clival lesion. The technique employed for the surgical procedure is presented here in detail as is our experience over two decades using this technique for tumors, inflammatory lesions and congenital abnormalities at the cranio-cervical junction. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterizing and Modulating Brain Circuitry through Transcranial Magnetic Stimulation Combined with Electroencephalography

PubMed Central

Farzan, Faranak; Vernet, Marine; Shafi, Mouhsin M. D.; Rotenberg, Alexander; Daskalakis, Zafiris J.; Pascual-Leone, Alvaro

2016-01-01

The concurrent combination of transcranial magnetic stimulation (TMS) with electroencephalography (TMS-EEG) is a powerful technology for characterizing and modulating brain networks across developmental, behavioral, and disease states. Given the global initiatives in mapping the human brain, recognition of the utility of this technique is growing across neuroscience disciplines. Importantly, TMS-EEG offers translational biomarkers that can be applied in health and disease, across the lifespan, and in humans and animals, bridging the gap between animal models and human studies. However, to utilize the full potential of TMS-EEG methodology, standardization of TMS-EEG study protocols is needed. In this article, we review the principles of TMS-EEG methodology, factors impacting TMS-EEG outcome measures, and the techniques for preventing and correcting artifacts in TMS-EEG data. To promote the standardization of this technique, we provide comprehensive guides for designing TMS-EEG studies and conducting TMS-EEG experiments. We conclude by reviewing the application of TMS-EEG in basic, cognitive and clinical neurosciences, and evaluate the potential of this emerging technology in brain research. PMID:27713691

77 FR 40628 - HUD's Fiscal Year (FY) 2012 Transformation Initiative: Natural Experiments Research Grant Program...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

... DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT [Docket No. FR-5600-N-18-C-1] HUD's Fiscal Year (FY) 2012 Transformation Initiative: Natural Experiments Research Grant Program, Cancellation AGENCY: Office... Availability (NOFA) ``Transformation Initiative: Natural Experiments Grant Program'' on Grants.gov . The close...

Two-Level factorial screening of new plasmid/strain combinations for prodution of recombinant-DNA products.

PubMed

Emborg, C; Jepsen, P K; Biedermann, K

1989-05-01

This article treats the basic problem of selection of experimental conditions for microbiological experiments for evaluation of newly isolated bacterial strains, mutants, or plasmid/strain combinations. For this purpose shake flask experiments in a 2(10-4)confounded factorial design at resolution IV with four blocks of 16 flasks were used. The design was used for testing of two new strain/plasmid combinations (E. coli MT 102/403-SD2 and W 3110/403-SD2) i.e., both strains with the same plasmid 403-SD2. Both strains were integrated in the design, so both strains were tested with nine factors (temperature, aeration, glucose, initial pH, pH regulation, reduced aeration, chloramphenicol, acetate, and glycerol). With both strains the interaction between initial pH and reduced aeration had a significant influence on the yield of the recombinant-DNA product nuclease. There was more than a factor of 10 between lowest and highest yield of product. In this interactive system the strains reacted differently. MT 102/403-SD2 had highest yields at high initial pH (8.4) and no reduction in aeration, whereas W 3110/403-SD2 had highest yields of nuclease at low initial pH (7.4) and reduced aeration (rubber stopper inserted after cultivation for 12 h). These data (and previous work) clearly demonstrate that it is impossible to suggest a simple set of experimental conditions for testing of new plasmid/strain combinations. It is clear that the exclusive application of a standardized growth technique e.g., LB-medium at 37 degrees C at an unspecified and uncontrolled aeration level, may lead to wrong conclusions on properties and potentials of now plasmid/strain combinations and may lead to rejection of useful strains or plasmids.

Awake craniotomy for glioma resection: Technical aspects and initial results in a single institution.

PubMed

Trimble, Gillian; McStravick, Clodagh; Farling, Peter; Megaw, Katie; McKinstry, Steven; Smyth, Graham; Law, Gillian; Courtney, Heather; Quigley, Gavin; Flannery, Thomas

2015-01-01

Although variations in the technique of awake craniotomy (AC) have been widely reported, a key member of this interdisciplinary procedure is the healthcare professional performing assessments of neurological function during resection. The expertise of the latter will depend on the neurological function to be tested and on available resources of the institution. This report details our initial experience of an AC service utilizing the expertise of a speech and language therapist (SLT) and an experienced neuro-physiotherapist (NP) to monitor patient function during glioma resection. Forty-five patients underwent 50 AC procedures for eloquently located gliomas over a 3-year period. Patients with a glioma involving speech or sensorimotor areas were assessed preoperatively by the SLT/NP respectively. The same therapist monitored the patient's neurological function intraoperatively and executed a rehabilitation program tailored to the needs of the patient in the postoperative period. Three patients underwent biopsy only, due to intraoperative seizures precluding intraoperative mapping (2 cases) or speech arrest on stimulation of a small recurrent tumor. The remaining 47 cases were suitable for repetitive neurological assessment "awake" during tumor debulking. One patient with a large sensorimotor tumor developed intraoperative hemiparesis due to outward brain herniation (which recovered postoperatively). Ten patients developed a new or worsened neurological deficit in the initial postoperative period (6 were detected intraoperatively), of which 5 eventually had resolution and returned to baseline function within 2 weeks. In our initial experience based anecdotally on a previous similar "non-awake" caseload, we have found AC with the input of the SLT/NP to be a key component in ensuring optimal functional outcomes for patients with gliomas in eloquently located areas.

Investigation of fast initialization of spacecraft bubble memory systems

NASA Technical Reports Server (NTRS)

Looney, K. T.; Nichols, C. D.; Hayes, P. J.

1984-01-01

Bubble domain technology offers significant improvement in reliability and functionality for spacecraft onboard memory applications. In considering potential memory systems organizations, minimization of power in high capacity bubble memory systems necessitates the activation of only the desired portions of the memory. In power strobing arbitrary memory segments, a capability of fast turn on is required. Bubble device architectures, which provide redundant loop coding in the bubble devices, limit the initialization speed. Alternate initialization techniques are investigated to overcome this design limitation. An initialization technique using a small amount of external storage is demonstrated.

Runaway transient simulation of a model Kaplan turbine

NASA Astrophysics Data System (ADS)

Liu, S.; Zhou, D.; Liu, D.; Wu, Y.; Nishi, M.

2010-08-01

The runaway transient is a typical transient process of a hydro power unit, where the rotational speed of a turbine runner rapidly increases up to the runaway speed under a working head as the guide vanes cannot be closed due to some reason at the load rejection. In the present paper, the characteristics of the runaway transient of a model Kaplan turbine having ns = 479(m-kW) is simulated by using a time-dependent CFD technique where equation of rotational motion of runner, continuity equation and unsteady RANS equations with RNG k-epsilon turbulence model are solved iteratively. In the calculation, unstructured mesh is used to the whole flow passage, which consists of several sub-domains: entrance, casing, stay vanes + guide vanes, guide section, runner and draft tube. And variable speed sliding mesh technique is used to exchange interface flow information between moving part and stationary part, and three-dimensional unstructured dynamic mesh technique is also adopted to ensure mesh quality. Two cases were treated in the simulation of runaway transient characteristics after load rejection: one is the rated operating condition as the initial condition, and the other is the condition at the maximum head. Regarding the runaway speed, the experimental speed is 1.45 times the initial speed and the calculation is 1.47 times the initial for the former case. In the latter case, the experiment and the calculation are 1.67 times and 1.69 times respectively. From these results, it is recognized that satisfactorily prediction will be possible by using the present numerical method. Further, numerical results show that the swirl in the draft-tube flow becomes stronger in the latter part of the transient process so that a vortex rope will occur in the draft tube and its precession will cause the pressure fluctuations which sometimes affect the stability of hydro power system considerably.

Fluid Phase Separation (FPS) experiment for flight on the shuttle in a Get Away Special (GAS) canister: Design and fabrication

NASA Technical Reports Server (NTRS)

1990-01-01

The separation of fluid phases in microgravity environments is of importance to environmental control and life support systems (ECLSS) and materials processing in space. A successful fluid phase separation experiment will demonstrate a proof of concept for the separation technique and add to the knowledge base of material behavior. The phase separation experiment will contain a premixed fluid that will be exposed to a microgravity environment. After the phase separation of the compound has occurred, small samples of each of the species will be taken for analysis on Earth. By correlating the time of separation and the temperature history of the fluid, it will be possible to characterize the process. The phase separation experiment is totally self-contained, with three levels of containment on all fluids, and provides all necessary electrical power and control. The controller regulates the temperature of the fluid and controls data logging and sampling. An astronaut-activated switch will initiate the experiment and an unmaskable interrupt is provided for shutdown. The experiment has been integrated into space available on a manifested Get Away Special (GAS) experiment, CONCAP 2, part of the Consortium for Materials Complex Autonomous Payload (CAP) Program, scheduled for STS 42 in April 1991. Presented here are the design and the production of a fluid phase separation experiment for rapid implementation at low cost.

Variational data assimilation for tropospheric chemistry modeling

NASA Astrophysics Data System (ADS)

Elbern, Hendrik; Schmidt, Hauke; Ebel, Adolf

1997-07-01

The method of variational adjoint data assimilation has been applied to assimilate chemistry observations into a comprehensive tropospheric gas phase model. The rationale of this method is to find the correct initial values for a subsequent atmospheric chemistry model run when observations scattered in time are available. The variational adjoint technique is esteemed to be a promising tool for future advanced meteorological forecasting. The stimulating experience gained with the application of four-dimensional variational data assimilation in this research area has motivated the attempt to apply the technique to air quality modeling and analysis of the chemical state of the atmosphere. The present study describes the development and application of the adjoint of the second-generation regional acid deposition model gas phase mechanism, which is used in the European air pollution dispersion model system. Performance results of the assimilation scheme using both model-generated data and real observations are presented for tropospheric conditions. In the former case it is demonstrated that time series of only few or even one measured key species convey sufficient information to improve considerably the analysis of unobserved species which are directly coupled with the observed species. In the latter case a Lagrangian approach is adopted where trajectory calculations between two comprehensively furnished measurement sites are carried out. The method allows us to analyze initial data for air pollution modeling even when only sparse observations are available. Besides remarkable improvements of the model performance by properly analyzed initial concentrations, it is shown that the adjoint algorithm offers the feasibility to estimate the sensitivity of ozone concentrations relative to its precursors.

An Investigation of the Sub-Microsecond Features of Dynamic Crack Propagation in PMMA and the Rdx-Based Explosive PBX 9205

NASA Astrophysics Data System (ADS)

Washabaugh, P. D.; Hill, L. G.

2007-12-01

A dynamic crack propagating in a brittle material releases enough thermal energy to produce visible light. The dynamic fracture of even macroscopically amorphous materials becomes unsteady as the crack propagation velocity approaches the material wave-speeds. The heat generated at a crack-tip, especially as it jumps, may be a mechanism to initiate a self-sustaining reaction in an energetic material. Experiments were conducted in specimens to simulate an infinite plate for ˜10 μs. The initial specimens were 152 mm square by 6 mm thick acrylic sheets, and were fabricated to study non-steady near-wave-speed crack propagation. A variant of this specimen embedded a 25 mm×3 mm PBX 9205 pellet to explore the influence of dynamic Mode-I cracks in these materials. The crack was initiated by up to 0.24 g of Detasheet placed along a precursor 50 mm long notch, with a shield to contain the reaction products and prevent propagation along the fractured surfaces. The crack was studied by means of a streak camera and a Fourier-filter of the light reflecting off the newly minted surfaces. The sub-microsecond behavior of holes initiating, preceding and coalescing with the main crack were observed in the PMMA samples. The embedding and mechanical loading of explosives by this technique did not initiate a self-sustaining reaction in preliminary testing.

Robotic-assisted laparoscopic exenteration in recurrent cervical cancer Robotics improved the surgical experience for 2 women with recurrent cervical cancer.

PubMed

Davis, Mitzie-Ann; Adams, Sarah; Eun, Daniel; Lee, David; Randall, Thomas C

2010-06-01

Pelvic exenteration can be used to cure women with a central pelvic recurrence or persistence of gynecologic malignancy after initial definitive therapy. Refinements in patient selection, operative techniques, and surgical instrumentation have significantly improved outcomes over the past 60 years, but the procedure is still associated with significant mortality, morbidity, and recovery time. New technologies have made it possible to approach radical gynecologic surgeries in a minimally invasive fashion. We present 2 patients successfully treated with robotic-assisted anterior pelvic exenteration for treatment of persistent or recurrent cervical cancer after definitive radiotherapy. Copyright 2010 Mosby, Inc. All rights reserved.

Experiments with a decision-theoretic scheduler

NASA Technical Reports Server (NTRS)

Hansson, Othar; Holt, Gerhard; Mayer, Andrew

1992-01-01

This paper describes DTS, a decision-theoretic scheduler designed to employ state-of-the-art probabilistic inference technology to speed the search for efficient solutions to constraint-satisfaction problems. Our approach involves assessing the performance of heuristic control strategies that are normally hard-coded into scheduling systems, and using probabilistic inference to aggregate this information in light of features of a given problem. BPS, the Bayesian Problem-Solver, introduced a similar approach to solving single-agent and adversarial graph search problems, yielding orders-of-magnitude improvement over traditional techniques. Initial efforts suggest that similar improvements will be realizable when applied to typical constraint-satisfaction scheduling problems.

Production of Highly Polarized Positrons Using Polarized Electrons at MeV Energies

NASA Astrophysics Data System (ADS)

Abbott, D.; Adderley, P.; Adeyemi, A.; Aguilera, P.; Ali, M.; Areti, H.; Baylac, M.; Benesch, J.; Bosson, G.; Cade, B.; Camsonne, A.; Cardman, L. S.; Clark, J.; Cole, P.; Covert, S.; Cuevas, C.; Dadoun, O.; Dale, D.; Dong, H.; Dumas, J.; Fanchini, E.; Forest, T.; Forman, E.; Freyberger, A.; Froidefond, E.; Golge, S.; Grames, J.; Guèye, P.; Hansknecht, J.; Harrell, P.; Hoskins, J.; Hyde, C.; Josey, B.; Kazimi, R.; Kim, Y.; Machie, D.; Mahoney, K.; Mammei, R.; Marton, M.; McCarter, J.; McCaughan, M.; McHugh, M.; McNulty, D.; Mesick, K. E.; Michaelides, T.; Michaels, R.; Moffit, B.; Moser, D.; Muñoz Camacho, C.; Muraz, J.-F.; Opper, A.; Poelker, M.; Réal, J.-S.; Richardson, L.; Setiniyaz, S.; Stutzman, M.; Suleiman, R.; Tennant, C.; Tsai, C.; Turner, D.; Ungaro, M.; Variola, A.; Voutier, E.; Wang, Y.; Zhang, Y.; PEPPo Collaboration

2016-05-01

The Polarized Electrons for Polarized Positrons experiment at the injector of the Continuous Electron Beam Accelerator Facility has demonstrated for the first time the efficient transfer of polarization from electrons to positrons produced by the polarized bremsstrahlung radiation induced by a polarized electron beam in a high-Z target. Positron polarization up to 82% have been measured for an initial electron beam momentum of 8.19 MeV /c , limited only by the electron beam polarization. This technique extends polarized positron capabilities from GeV to MeV electron beams, and opens access to polarized positron beam physics to a wide community.

Making a home in space

NASA Technical Reports Server (NTRS)

Aaron, John; Gabris, Edward A.; Sulzman, Frank M.; Connors, Mary M.; Pilcher, Carl

1989-01-01

NASA's Office of Aeronautics and Space Technology has undertaken a series of manned space presence-development efforts under the aegis of the Civil Space Technology Initiative (CSTI) and Project Pathfinder. Typical of these CSTI efforts is the Aeroassist Flight Experiment, which will demonstrate techniques suitable in aerobrake design for slow trajectories to Mars and for lunar mission return. Long-duration human operations in space are a major element of Pathfinder, giving attention to such problems as space radiation exposure effects that could be several orders of magnitude greater on interplanetary exploration missions than on typical Space Shuttle flights. Mars Observer and Lunar Observer orbital missions are planned as a steppingstone to manned planetary exploration.

Langley Research Center's Unitary Plan Wind Tunnel: Testing Capabilities and Recent Modernization Activities

NASA Technical Reports Server (NTRS)

Micol, John R.

2001-01-01

Description, capabilities, initiatives, and utilization of the NASA Langley Research Center's Unitary Plan Wind Tunnel are presented. A brief overview of the facility's operational capabilities and testing techniques is provided. A recent Construction of Facilities (CoF) project to improve facility productivity and efficiency through facility automation has been completed and is discussed. Several new and maturing thrusts are underway that include systematic efforts to provide credible assessment for data quality, modifications to the new automation control system for increased compatibility with the Modern Design Of Experiments (MDOE) testing methodology, and process improvements for better test coordination, planning, and execution.