Final Rule for Control of Hazardous Air Pollutants From Mobile Sources: Early Credit Technology Requirement Revision

EPA Pesticide Factsheets

EPA is taking final action to revise the February 26, 2007 mobile source air toxics rule’s requirements that specify which benzene control technologies a refiner may utilize to qualify to generate early benzene credits.

An Integrated Water Treatment Technology Solution for Sustainable Water Resource Management in the Marcellus Shale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthew Bruff; Ned Godshall; Karen Evans

2011-04-30

This Final Scientific/ Technical Report submitted with respect to Project DE-FE0000833 titled 'An Integrated Water Treatment Technology Solution for Sustainable Water Resource Management in the Marcellus Shale' in support of final reporting requirements. This final report contains a compilation of previous reports with the most current data in order to produce one final complete document. The goal of this research was to provide an integrated approach aimed at addressing the increasing water resource challenges between natural gas production and other water stakeholders in shale gas basins. The objective was to demonstrate that the AltelaRain{reg_sign} technology could be successfully deployed inmore » the Marcellus Shale Basin to treat frac flow-back water. That objective has been successfully met.« less

Amendment and Innovative Technology Waiver for New Source Performance Standards for Kraft Pulp Mills: 1985 Final Rule (50 FR 6316)

EPA Pesticide Factsheets

This document is a copy of the Federal Register publication of the February 14, 1985 Final Rule for the Amendment and Innovative Technology Waiver for New Source Performance Standards for Kraft Pulp Mills.

Final Petroleum Refinery Sector Risk and Technology Review and New Source Performance Standards (NSPS) Fact Sheets

EPA Pesticide Factsheets

This page contains 3 September 2015 fact sheets with information regarding the final residual risk and technology review for the petroleum refinery source categories. The fact sheets provide an overview, a summary of changes, effects for the community.

Final priority; Rehabilitation Services Administration--Assistive Technology Alternative Financing Program. Final priority.

PubMed

2014-08-14

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Assistive Technology Alternative Financing Program administered by the Rehabilitation Services Administration (RSA). The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. This priority is designed to ensure that the Department funds high-quality assistive technology (AT) alternative financing programs (AFPs) that meet rigorous standards in order to enable individuals with disabilities to access and acquire assistive technology devices and services necessary to achieve education, community living, and employment goals.

Technology for NASA's Planetary Science Vision 2050.

NASA Technical Reports Server (NTRS)

Lakew, B.; Amato, D.; Freeman, A.; Falker, J.; Turtle, Elizabeth; Green, J.; Mackwell, S.; Daou, D.

2017-01-01

NASAs Planetary Science Division (PSD) initiated and sponsored a very successful community Workshop held from Feb. 27 to Mar. 1, 2017 at NASA Headquarters. The purpose of the Workshop was to develop a vision of planetary science research and exploration for the next three decades until 2050. This abstract summarizes some of the salient technology needs discussed during the three-day workshop and at a technology panel on the final day. It is not meant to be a final report on technology to achieve the science vision for 2050.

ENVIRONMENTAL TECHNOLOGY VERIFICATION FOR AIR POLLUTION CONTROL TECHNOLOGIES: FINAL REPORT

EPA Science Inventory

The technical objective of the Environmental Technology Verification (ETV) Program's Air Pollution Control Technology (APCT) Center is to verify environmental technology performance by obtaining objective quality-assured data, thus providing potential purchasers and permitters wi...

Development of Medical Technology for Contingency Response to Marrow Toxic Agents

DTIC Science & Technology

2012-03-31

Development of Medical Technology for Contingency Response to Marrow Toxic Agents - Final Performance/Technical Report for March 01, 2010 to February 28...Development of Medical Technology for Contingency Response To Marrow Toxic Agents FINAL REPORT March 1, 2010 – March 31, 2012 National...Buccal Swabs 38 IIB.1.5 Enhancing HLA Data for Selected Donors 43 IIB.1.6 Maintain a Quality Control Program 46 IIB.2.1 Collection of Primary Data

Examining Advanced Technologies for Benefits to Persons with Sensory Impairments. Final Report.

ERIC Educational Resources Information Center

Hinton, Daniel E., Sr.

This final report describes activities and products of an 18-month study on improving access of persons with sensory impairments to media, telecommunications, electronic correspondence, and other communications devices by means of technological advancements. Ten scenarios were developed which describe potential applications of: (1) Braille devices…

77 FR 70689 - Approval and Promulgation of Implementation Plans; Tennessee; Regional Haze State Implementation...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-27

... Retrofit Technology Requirements for Eastman Chemical Company AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: EPA is finalizing approval of the Best Available Retrofit Technology (BART... retrofitting its facility pursuant to the BART determination for SO 2 emissions (hereafter referred to as the...

TNX GeoSiphon Cell (TGSC-1) Phase II Single Cell Deployment/Demonstration Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phifer, M.A.

1999-04-15

This Phase II final report documents the Phase II testing conducted from June 18, 1998 through November 13, 1998, and it focuses on the application of the siphon technology as a sub-component of the overall GeoSiphon Cell technology. [Q-TPL-T-00004

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Final ACT configuration evaluation

NASA Technical Reports Server (NTRS)

1982-01-01

The Final ACT Configuration Evaluation Task of the Integrated Application of Active Controls (IAAC) technology project within the energy efficient transport program is summarized. The Final ACT Configuration, through application of Active Controls Technology (ACT) in combination with increased wing span, exhibits significant performance improvements over the conventional baseline configuration. At the design range for these configurations, 3590 km, the block fuel used is 10% less for the Final ACT Configuration, with significant reductions in fuel usage at all operational ranges. Results of this improved fuel usage and additional system and airframe costs and the complexity required to achieve it were analyzed to determine its economic effects. For a 926 km mission, the incremental return on investment is nearly 25% at 1980 fuel prices. For longer range missions or increased fuel prices, the return is greater. The technical risks encountered in the Final ACT Configuration design and the research and development effort required to reduce these risks to levels acceptable for commercial airplane design are identified.

Research of interaction between technological and material parameters during densification of sunflower hulls

NASA Astrophysics Data System (ADS)

Križan, Peter; Matúš, Miloš; Beniak, Juraj; Šooš, Ľubomír

2018-01-01

During the biomass densification can be recognized various technological variables and also material parameters which significantly influences the final solid biofuels (pellets) quality. In this paper, we will present the research findings concerning relationships between technological and material variables during densification of sunflower hulls. Sunflower hulls as an unused source is a typical product of agricultural industry in Slovakia and belongs to the group of herbaceous biomass. The main goal of presented experimental research is to determine the impact of compression pressure, compression temperature and material particle size distribution on final biofuels quality. Experimental research described in this paper was realized by single-axis densification, which was represented by experimental pressing stand. The impact of mentioned investigated variables on the final briquettes density and briquettes dilatation was determined. Mutual interactions of these variables on final briquettes quality are showing the importance of mentioned variables during the densification process. Impact of raw material particle size distribution on final biofuels quality was also proven by experimental research on semi-production pelleting plant.

Innovative technology: Slurry-phase biodegradation. Fact sheet (Final)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-11-01

The fact sheet provides technology description, site characteristics affecting treatment feasibility, technology considerations, and technology status for Slurry Phase Biodegradation (SPB). The sheet describes how SPB is potentially effective in treating various organic contaminants.

Learning with Portable Digital Devices in Australian Schools: 20 Years On!

ERIC Educational Resources Information Center

Newhouse, C. Paul

2014-01-01

Portable computing technologies such as laptops, tablets, smartphones, wireless networking, voice/stylus input, and plug and play peripheral devices, appear to offer the means of finally realising much of the long heralded vision for computers to support learning in schools. There is the possibility for the technology to finally become a…

Health information technology: initial set of standards, implementation specifications, and certification criteria for electronic health record technology. Interim final rule.

PubMed

2010-01-13

The Department of Health and Human Services (HHS) is issuing this interim final rule with a request for comments to adopt an initial set of standards, implementation specifications, and certification criteria, as required by section 3004(b)(1) of the Public Health Service Act. This interim final rule represents the first step in an incremental approach to adopting standards, implementation specifications, and certification criteria to enhance the interoperability, functionality, utility, and security of health information technology and to support its meaningful use. The certification criteria adopted in this initial set establish the capabilities and related standards that certified electronic health record (EHR) technology will need to include in order to, at a minimum, support the achievement of the proposed meaningful use Stage 1 (beginning in 2011) by eligible professionals and eligible hospitals under the Medicare and Medicaid EHR Incentive Programs.

Cockpit Automation Technology CSERIAC-CAT

DTIC Science & Technology

1991-06-01

AD-A273 124 AL-TR-1991-0078 A R COCKPIT AUTOMATION TECHNOLOGY M CSERIAC- CAT S JULY 1989 - DEC 1990: FINAL REPORT T R Trudy S. Abrams Cindy D. Martin...TITLE AND SUBTITLE 5. FUNDING NUMBERS Cockpit Automation Technology CSERIAC- CAT JUL 89 - DEC 90 PE 62202F Final Report (U) PR 7184 ,___,TA 12 6. AUTHOR(S...Boeing-developed CAT software tools, and for facilitating their use by the cockpit design community. A brief description of the overall task is given

75 FR 36157 - Establishment of the Temporary Certification Program for Health Information Technology

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-24

...This final rule establishes a temporary certification program for the purposes of testing and certifying health information technology. This final rule is established under the authority granted to the National Coordinator for Health Information Technology (the National Coordinator) by section 3001(c)(5) of the Public Health Service Act (PHSA), as added by the Health Information Technology for Economic and Clinical Health (HITECH) Act. The National Coordinator will utilize the temporary certification program to authorize organizations to test and certify Complete Electronic Health Records (EHRs) and/or EHR Modules, thereby making Certified EHR Technology available prior to the date on which health care providers seeking incentive payments available under the Medicare and Medicaid EHR Incentive Programs may begin demonstrating meaningful use of Certified EHR Technology.

Development of Advanced Technologies to Reduce Design, Fabrication and Construction Costs for Future Nuclear Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

DiNunzio, Camillo A.; Gupta, Abhinav; Golay, Michael

2002-11-30

This report presents a summation of the third and final year of a three-year investigation into methods and technologies for substantially reducing the capital costs and total schedule for future nuclear plants. In addition, this is the final technical report for the three-year period of studies.

Distance Education Technology Study. Final Report: Executive Summary presented to: Wisconsin Educational Communications Board.

ERIC Educational Resources Information Center

Evans Associates, Thiensville, WI.

This document consists of the final report and executive summary of a distance education technology study conducted on behalf of the Wisconsin Educational Communications Board (WECB) during 1992-93 in order to provide information to assist the educational institutions of the state in formulating strategic directions for the development of distance…

Interactions of Science and Technology in the Innovative Process: Some Case Studies. Final Report.

ERIC Educational Resources Information Center

Battelle Memorial Inst., Columbus, OH. Columbus Labs.

This is the final report of the latest effort in a series sponsored by the National Science Foundation on the innovation process. It adds to the store of retrospective case studies by documenting historically the significant events in several technological innovations of high social impact. These cases, drawn together by the Battelle Columbus…

Disruptive technologies and transportation : final report.

DOT National Transportation Integrated Search

2016-06-01

Disruptive technologies refer to innovations that, at first, may be considered unproven, lacking refinement, relatively unknown, or even impractical, but ultimately they supplant existing technologies and/or applications. In general, disruptive techn...

Technology Assessment for Powertrain Components Final Report CRADA No. TC-1124-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tokarz, F.; Gough, C.

LLNL utilized its defense technology assessment methodologies in combination with its capabilities in the energy; manufacturing, and transportation technologies to demonstrate a methodology that synthesized available but incomplete information on advanced automotive technologies into a comprehensive framework.

76 FR 4079 - Information Technology (IT) Security

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-24

... Technology (IT) Security AGENCY: National Aeronautics and Space Administration. ACTION: Final rule. SUMMARY: NASA is revising the NASA FAR Supplement (NFS) to update requirements related to Information Technology... Security clause. However, due to the critical importance of protecting the Agency's Information Technology...

Two men with multiple disabilities carry out an assembly work activity with the support of a technology system.

PubMed

Lancioni, Giulio E; Singh, Nirbhay N; O'Reilly, Mark F; Green, Vanessa A; Oliva, Doretta; Campodonico, Francesca

2013-10-01

To assess whether two persons with multiple disabilities could learn a work activity (i.e., assembling trolley wheels) with the support of a technology system. After an initial baseline, the study compared the effects of intervention sessions relying on the technology system (which called the participants to the different workstations and provided feedback and final stimulation) with the effects of intervention sessions carried out without technology. The two types of intervention sessions were conducted according to an alternating treatments design. Eventually, only intervention sessions relying on the technology system were used. Both participants managed to assemble wheels independently during intervention sessions relying on the technology system while they failed during sessions without the system. Their performance was strengthened during the final part of the study, in which only sessions with the system occurred. Technology may be critical in helping persons with multiple disabilities manage multi-step work activities.

Women in Science and Technology: The Institutional Ecology Approach. Volume I: Final Research Report.

ERIC Educational Resources Information Center

Byrne, Eileen M.

This document is the final research report of the University of Queensland Women in Science and Technology in Australia (WISTA) project. The report is a policy review study conducted from 1985 to 1990, of the factors that act as critical filters or positive factors that hinder or help women's access to and progression in certain scientific and…

CAPITAL COSTS OF ARSENIC REMOVAL TECHNOLOGIES, U.S. EPA ARSENIC REMOVAL TECHNOLOGY DEMONSTRATION PROGRAM ROUND 1

EPA Science Inventory

On January 18, 2001, the U.S. Environmental Protection Agency (EPA) finalized the maximum contaminant level (MCL) for arsenic at 0.01 mg/L. EPA subsequently revised the rule text to express the MCL as 0.010 mg/L (10 μg/L). The final rule requires all community and non-transient, ...

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Wing planform study and final configuration selection

NASA Technical Reports Server (NTRS)

1981-01-01

The Wing Planform Study and Final Configuration Selection Task of the Integrated Application of Active Controls (IAAC) Technology Project within the Energy Efficient Transport Program is documented. Application of Active Controls Technology (ACT) in combination with increased wing span resulted in significant improvements over the Conventional Baseline Configuration (Baseline) and the Initial ACT Configuration previously established. The configurations use the same levels of technology, takeoff gross weight, and payload as the Baseline. The Final ACT Configuration (Model 768-107) incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 44% reduction in horizontal tail size), lateral/directional-augmented stability, an angle-of-attack limiter, and wing-load alleviation. Flutter-mode control was not beneficial for this configuration. This resulted in an 890 kg (1960 lb) reduction in airplane takeoff gross weight and a 9.8% improvement in cruise lift/drag. At the Baseline mission range (3589 km 1938 nmi), this amounts to 10% block-fuel reduction. Results of this task strongly indicate that the IAAC Project should proceed with the Final ACT evaluation, and begin the required control system development and test.

Development document for final best conventional technology effluent limitations guidelines for the pharmaceutical manufacturing point source category. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Farrell, T.; Hund, F.

1986-12-01

The document presents the technical rationale for best conventional technology (BCI) effluent limitations guidelines for the pharmaceutical manufacturing point-source category as required by the Clean Water Act of 1977 (P.L. 95-217, the Act). The document describes the technologies considered as the bases for BCT limitations. Section II of this document summarizes the rulemaking process. Sections III through V describe the technical data and engineering analyses used to develop the regulatory technology options. The costs and removals associated with each technology option for each plant and the application of the BCT cost test methodology are presented in Section VI. BCI limitationsmore » bases on the best conventional pollutant control technology are to be achieved by existing direct-discharging facilities.« less

NASA-KSC/Florida Dual Use Technology Partnership

NASA Technical Reports Server (NTRS)

Kershaw, David

2001-01-01

This document constitutes the Technological Research and Development Authority's (TRDA) Final Reports for the NASA-KSC/Florida Dual Use Technology Partnership grant covering the period December 1, 1999 through November 30, 2000. The NASA Grant and Cooperative Agreement Handbook requires the TRDA to provide NASA with a final report on Subject Inventions, Federal Cash Transactions, Summary Research, and Federally-Owned Property. This report contains those requirements as well as a description of the TRDA's grant performance related to activities undertaken, difficulties incurred, remedial actions, and the current financial status of the contract.

Continuation of Crosscutting Technology Development at Cast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Roe-Hoan

2012-03-31

This Final Technical Report describes progress made on the sub-projects awarded in the Cooperative Agreement DE-FC26-05NT42457: Continuation of Crosscutting Technology Development at Center for Advanced Separation Technologies (CAST). The final reports for each sub-project are attached in the appendix. Much of the research to be conducted with Cooperative Agreement funds will be longer-term, high-risk, basic research and will be carried out in five broad areas: a) Solid-solid separation b) Solid-liquid separation c) Chemical/Biological Extraction d) Modeling and Control, and e) Environmental Control.

76 FR 68189 - Healthcare Technology Holdings, Inc.; Analysis of Proposed Agreement Containing Consent Orders To...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-03

... FEDERAL TRADE COMMISSION [File No. 111 0097] Healthcare Technology Holdings, Inc.; Analysis of... Public Comment I. Introduction The Federal Trade Commission (``Commission'') has accepted from Healthcare Technology Holdings, Inc. (``Healthcare Technology''), subject to final approval, an Agreement Containing...

Applications of aerospace technology in the electric power industry

NASA Technical Reports Server (NTRS)

1973-01-01

An overview of the electric power industry, selected NASA contributions to progress in the industry, linkages affecting the transfer and diffusion of technology, and, finally, a perspective on technology transfer issues are presented.

SATA II - Stochastic Algebraic Topology and Applications

DTIC Science & Technology

2017-01-30

AFRL-AFOSR-UK-TR-2017-0018 SATA II - Stochastic Algebraic Topology and Applications 150032 Robert Adler TECHNION ISRAEL INSTITUTE OF TECHNOLOGY Final...REPORT TYPE Final 3. DATES COVERED (From - To) 15 Dec 2014 to 14 Dec 2016 4. TITLE AND SUBTITLE SATA II - Stochastic Algebraic Topology and Applications ...has recently been submitted to AFOSR. 15. SUBJECT TERMS Network Theory, Sensor Technology, Mathematical Modeling, EOARD 16. SECURITY CLASSIFICATION OF

Analytical Ferrography Standardization.

DTIC Science & Technology

1982-01-01

AD-AII6 508 MECHANICAL TECHNOLOGY INC LATHAM NY RESEARCH AND 0EV--ETC F/6 7/4 ANALYTICAL FERROGRAPHY STANDARDIZATION. (U) JAN 82 P A SENHOLZI, A S...ii Mwl jutio7 Unimte SMechanical Technology Incorporated Research and Development Division ReerhadDvlpetDvso I FINAL REPORT ANALYTICAL FERROGRAPHY ...Final Report MTI Technical Report No. 82TRS6 ANALYTICAL FERROGRAPHY STANDARDIZATION P. B. Senholzi A. S. Maciejewski Applications Engineering Mechanical

Technology Use in Science Instruction (TUSI): Aligning the Integration of Technology in Science Instruction in Ways Supportive of Science Education Reform

NASA Astrophysics Data System (ADS)

Campbell, Todd; Abd-Hamid, Nor Hashidah

2013-08-01

This study describes the development of an instrument to investigate the extent to which technology is integrated in science instruction in ways aligned to science reform outlined in standards documents. The instrument was developed by: (a) creating items consistent with the five dimensions identified in science education literature, (b) establishing content validity with both national and international content experts, (c) refining the item pool based on content expert feedback, (d) piloting testing of the instrument, (e) checking statistical reliability and item analysis, and (f) subsequently refining and finalization of the instrument. The TUSI was administered in a field test across eleven classrooms by three observers, with a total of 33 TUSI ratings completed. The finalized instrument was found to have acceptable inter-rater intraclass correlation reliability estimates. After the final stage of development, the TUSI instrument consisted of 26-items separated into the original five categories, which aligned with the exploratory factor analysis clustering of the items. Additionally, concurrent validity of the TUSI was established with the Reformed Teaching Observation Protocol. Finally, a subsequent set of 17 different classrooms were observed during the spring of 2011, and for the 9 classrooms where technology integration was observed, an overall Cronbach alpha reliability coefficient of 0.913 was found. Based on the analyses completed, the TUSI appears to be a useful instrument for measuring how technology is integrated into science classrooms and is seen as one mechanism for measuring the intersection of technological, pedagogical, and content knowledge in science classrooms.

CONTROLLING SO2 EMISSIONS: A REVIEW OF TECHNOLOGIES

EPA Science Inventory

The report describes flue gas desulfurization (FGD) technologies, assesses their applications, and characterizes their performance. Additionally, it describes some of the advancements that have occurred in FGD technologies. Finally, it presents an analysis of the costs associated...

Comprehensive Child Welfare Information System. Final rule.

PubMed

2016-06-02

This final rule replaces the Statewide and Tribal Automated Child Welfare Information Systems (S/TACWIS) rule with the Comprehensive Child Welfare Information System (CCWIS) rule. The rule also makes conforming amendments in rules in related requirements. This rule will assist title IV-E agencies in developing information management systems that leverage new innovations and technology in order to better serve children and families. More specifically, this final rule supports the use of cost-effective, innovative technologies to automate the collection of high-quality case management data and to promote its analysis, distribution, and use by workers, supervisors, administrators, researchers, and policy makers.

NASA Technology Area 1: Launch Propulsion Systems

NASA Technical Reports Server (NTRS)

McConnaughey, Paul; Femminineo, Mark; Koelfgen, Syri; Lepsch, Roger; Ryan, Richard M.; Taylor, Steven A.

2011-01-01

This slide presentation reviews the technology advancements plans for the NASA Technology Area 1, Launch Propulsion Systems Technology Area (LPSTA). The draft roadmap reviews various propulsion system technologies that will be developed during the next 25 + years. This roadmap will be reviewed by the National Research Council which will issue a final report, that will include findings and recommendations.

Performance Testing in Electronic Technology. Final Report.

ERIC Educational Resources Information Center

Williamson, Bert; Pedersen, Joe F.

This set of 21 performance tests in electronics technology was developed on the basis of a review of commercial and noncommercial instructional materials dealing with electronics technology. The tests, which were reviewed by a group of community college instructors and an advisory committee for electronics technology, address the following…

Advanced Technology Training Program for the Apparel Industry. Final Report.

ERIC Educational Resources Information Center

El Paso Community Coll., TX.

A project developed rapid response, advanced technology courses that met the apparel market labor needs of the El Paso (Texas) community. Courses were designed for four options: computerized marker making and pattern grading, computerized front office systems, high technology machinery operation, and high technology machinery mechanics. The…

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Wing planform study and final configuration selection

NASA Technical Reports Server (NTRS)

1981-01-01

This report summarizes the Wing Planform Study Task and Final Configuration Selection of the Integrated Application of Active Controls (IAAC) Technology Project within the Energy Efficient Transport Program. Application of Active Controls Technology (ACT) in combination with increased wing span resulted in significant improvements over the Conventional Baseline Configuration (Baseline) and the Initial ACT Configuration previously established. The configurations use the same levels of technology (except for ACT), takeoff gross weight, and payload as the Baseline. The Final ACT Configuration (Model 768-107) incorporates pitch-augmented stability (which enabled an approximately 10% aft shift in cruise center of gravity and a 45% reduction in horizontal tail sizes), lateral/directional-augmented stability, an angle-of-attack limiter, and wing-load alleviation. Flutter-mode control was not beneficial for this configuration. This resulted in an 890 kg (1960 lb) reduction in airplane takeoff gross weight and a 9.8% improvement in cruise lift/drag. At the Baseline mission range (3590 km) (1938 nmi), this amounts to 10% block fuel reduction. Good takeoff performance at high-altitude airports on a hot day was also achieved. Results of this task strongly indicate that the IAAC Project should proceed with the Final ACT evaluation and begin the required control system development and testing.

Urban Maglev Technology Development Program : Colorado Maglev Project : part 2 final report

DOT National Transportation Integrated Search

2004-06-01

The overall objective of the urban maglev transit technology development program is to develop magnetic levitation technology that is a cost effective, reliable, and environmentally sound transit option for urban mass transportation in the United Sta...

Adapting construction staking to modern technology : final report.

DOT National Transportation Integrated Search

2017-08-01

This report summarizes the tasks and findings of the ICT Project R27-163, Adapting Construction Staking to Modern Technology, which aims to develop written procedures for the use of modern technologies (such as GPS and civil information modeling) in ...

Medicare and Medicaid programs; modifications to the Medicare and Medicaid Electronic Health Record (EHR) Incentive Program for 2014 and other changes to EHR Incentive Program; and health information technology: revision to the certified EHR technology definition and EHR certification changes related to standards. Final rule.

PubMed

2014-09-04

This final rule changes the meaningful use stage timeline and the definition of certified electronic health record technology (CEHRT) to allow options in the use of CEHRT for the EHR reporting period in 2014. It also sets the requirements for reporting on meaningful use objectives and measures as well as clinical quality measure (CQM) reporting in 2014 for providers who use one of the CEHRT options finalized in this rule for their EHR reporting period in 2014. In addition, it finalizes revisions to the Medicare and Medicaid EHR Incentive Programs to adopt an alternate measure for the Stage 2 meaningful use objective for hospitals to provide structured electronic laboratory results to ambulatory providers; to correct the regulation text for the measures associated with the objective for hospitals to provide patients the ability to view online, download, and transmit information about a hospital admission; and to set a case number threshold exemption for CQM reporting applicable for eligible hospitals and critical access hospitals (CAHs) beginning with FY 2013. Finally, this rule finalizes the provisionally adopted replacement of the Data Element Catalog (DEC) and the Quality Reporting Document Architecture (QRDA) Category III standards with updated versions of these standards.

Evaluation of the Texas Technology Immersion Pilot: Final Outcomes for a Four-Year Study (2004-05 to 2007-08)

ERIC Educational Resources Information Center

Shapley, Kelly; Sheehan, Daniel; Maloney, Catherine; Caranikas-Walker, Fanny

2009-01-01

The Technology Immersion Pilot (TIP), created by the Texas Legislature in 2003, was based on the assumption that the use of technology in Texas public schools could be achieved more effectively by "immersing" schools in technology rather than by introducing technology resources, such as hardware, software, digital content, and educator…

An Emerging Technology Curriculum. Education for Technology Employment Project. Final Report.

ERIC Educational Resources Information Center

Harms, Dan; And Others

Individualized, competency-based curriculum materials were developed for a course on Principles of Technology, Units 1-6. New and updated curriculum materials in Drafting and Electronics and the Principles of Technology units were pilot tested in area vocational center settings in Illinois. A computer maintenance program was also developed but not…

ENVIRONMENTAL TECHNOLOGY VERIFICATION COATINGS AND COATING EQUIPMENT PROGRAM (ETV CCEP), FINAL TECHNOLOGY APPLICATIONS GROUP TAGNITE--TESTING AND QUALITY ASSURANCE PLAN (T/QAP)

EPA Science Inventory

The overall objective of the Environmental Testing and Verification Coatings and Coating Equipment Program is to verify pollution prevention and performance characteristics of coating technologies and make the results of the testing available to prospective coating technology use...

High Technology Technical Training Needs Assessment. Final Report 1983-84.

ERIC Educational Resources Information Center

Middlesex County Coll., Edison, NJ.

A project sought to produce adequate data on high technology training needs in New Jersey's Middlesex County College's service area. Of 168 individuals at high technology companies who were sent surveys, 52 returned usable surveys. Respondents supplied information on the impact of high technology on the company over the next five years, the…

Diffusion of Appropriate Educational Technology in Open & Distance Learning in Developing Commonwealth Countries. Final Project Report.

ERIC Educational Resources Information Center

Williams, Roy

The Diffusion of Appropriate Educational Technology in Open and Distance Learning in Developing Countries project was designed to determine awareness and use of educational technologies and communications media in developing countries, to identify factors constraining wider use of educational technologies by developing nations, and to explore…

Project on Application of Modern Communication Technologies to Educational Networking. Final Technical Report.

ERIC Educational Resources Information Center

Morgan, Robert P.; Eastwood, Lester F., Jr.

Research on this National Science Foundation grant to study the application of modern communications technology to educational networking was divided into three parts: assessment of the role of technology in non-traditional post-secondary education; assessment of communications technologies and educational services of current or potential future…

Early Childhood Technology Integrated Instructional System (EC-TIIS) Phase 1: A Final Report

ERIC Educational Resources Information Center

Hutinger, Patricia; Robinson, Linda; Schneider, Carol

2004-01-01

The Early Childhood Technology Integrated Instructional System (EC-TIIS), a Steppingstones of Technology Innovation Phase 1--Development project, was developed by the Center for Best Practices in Early Childhood (the Center) at Western Illinois University as an online instructional system. EC-TIIS' ultimate goal was to improve technology services…

Assessment of advanced technologies for transit and rideshare applications : final report

DOT National Transportation Integrated Search

This report presents the results of a study to examine advanced technologies and systems that can be applied to high occupancy vehicles, ridesharing and transit needs. Advanced technologies can be used to encourage the use of transit and rideshare fa...

Urban Maglev Technology Development Program : Colorado Maglev Project : part 1 : executive summary of final report

DOT National Transportation Integrated Search

2004-06-01

The overall objective of the urban maglev transit technology development program is to develop magnetic levitation technology that is a cost effective, reliable, and environmentally sound transit option for urban mass transportation in the United Sta...

New Concepts in Electromagnetic Materials and Antennas

DTIC Science & Technology

2015-01-01

Bae-Ian Wu Antennas & Electromagnetics Technology Branch Multispectral Sensing & Detection Division JANUARY 2015 Final Report...Signature// //Signature// BRADLEY A. KRAMER, Program Manager TONY C. KIM, Branch Chief Antenna & Electromagnetic Technology ...Branch Antenna & Electromagnetic Technology Branch Multispectral Sensing & Detection Division Multispectral Sensing & Detection Division

A remote sensing and GIS-enabled highway asset management system : final report.

DOT National Transportation Integrated Search

2016-04-01

The objective of this project is to validate the use of commercial remote sensing and spatial information : (CRS&SI) technologies, including emerging 3D line laser imaging technology, mobile LiDAR, image : processing algorithms, and GPS/GIS technolog...

Illinois Clean Coal Institute 2005 annual report. Final technical report for the period September 1st, 2004, through August 31, 2005 on projects funded by the Illinois Department of Commerce and Economic Opportunity

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2005-11-08

This final technical report contains the abstracts and executive summaries of projects funded through the Illinois Clean Coal Institute solicitation entitled 'Request for proposals No. 04-1(ICCI/RFP04-1)'. Support of these projects is by the Office of Coal Development and Department of Commerce and Economic Opportunity. The projects fall into the following categories: advanced coal mining technologies; coal preparation and coal production business practice; management of coal combustion byproducts; commercialization and technology transfer. Final project extensions are also recorded.

32 CFR 37.905 - Must I make receipt of the final performance report a condition for final payment?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 1 2012-07-01 2012-07-01 false Must I make receipt of the final performance report a condition for final payment? 37.905 Section 37.905 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS...

32 CFR 37.905 - Must I make receipt of the final performance report a condition for final payment?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Must I make receipt of the final performance report a condition for final payment? 37.905 Section 37.905 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS...

32 CFR 37.905 - Must I make receipt of the final performance report a condition for final payment?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 1 2013-07-01 2013-07-01 false Must I make receipt of the final performance report a condition for final payment? 37.905 Section 37.905 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS...

32 CFR 37.905 - Must I make receipt of the final performance report a condition for final payment?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 1 2011-07-01 2011-07-01 false Must I make receipt of the final performance report a condition for final payment? 37.905 Section 37.905 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DoD GRANT AND AGREEMENT REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS...

Mixed-waste treatment -- What about the residuals?. A compartive analysis of MSO and incineration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, T.; Carpenter, C.; Cummins, L.

1993-11-01

Incineration currently is the best demonstrated available technology for the large inventory of U.S. Department of Energy (DOE) mixed waste. However, molten salt oxidation (MSO) is an alternative thermal treatment technology with the potential to treat a number of these wastes. Of concern for both technologies is the final waste forms, or residuals, that are generated by the treatment process. An evaluation of the two technologies focuses on 10 existing DOE waste streams and current hazardous-waste regulations, specifically for the delisting of ``derived-from`` residuals. Major findings include that final disposal options are more significantly impacted by the type of wastemore » treated and existing regulations than by the type of treatment technology; typical DOE waste streams are not good candidates for delisting; and mass balance calculations indicate that MSO and incineration generate similar quantities (dry) and types of residuals.« less

77 FR 54163 - Health Information Technology: Standards, Implementation Specifications, and Certification...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

...With this final rule, the Secretary of Health and Human Services adopts certification criteria that establish the technical capabilities and specify the related standards and implementation specifications that Certified Electronic Health Record (EHR) Technology will need to include to, at a minimum, support the achievement of meaningful use by eligible professionals, eligible hospitals, and critical access hospitals under the Medicare and Medicaid EHR Incentive Programs beginning with the EHR reporting periods in fiscal year and calendar year 2014. This final rule also makes changes to the permanent certification program for health information technology, including changing the program's name to the ONC HIT Certification Program.

Crystallization processes in pharmaceutical technology and drug delivery design

NASA Astrophysics Data System (ADS)

Shekunov, B. Yu; York, P.

2000-04-01

Crystallization is a major technological process for particle formation in pharmaceutical industry and, in addition, plays an important role in defining the stability and drug release properties of the final dosage forms. Industrial and regulatory aspects of crystallization are briefly reviewed with reference to solid-state properties of pharmaceuticals. Crystallization, incorporating wider definition to include precipitation and solid-state transitions, is considered in terms of preparation of materials for direct compression, formation of amorphous, solvated and polymorphic forms, chiral separation of drugs, production of materials for inhalation drug delivery and injections. Finally, recent developments in supercritical fluid particle technology is considered in relationship to the areas discussed.

Helicopter Dynamic Performance Program. Volume 2. User’s Manual

DTIC Science & Technology

1980-07-01

Technologies Corporation Stratford, Connecticut 06602 July 1980 Final Report / • ., . Approved for public release; I distribution unlimited. ; A - Prepared...for : APPLIED TECHNOLOGY LABORATORY U. S. ARMY RESEARCH AND TECHNOLOGY LABORATORIES (AVRADCOM) Fort Eustis, Va. 23604 80 8 27 D APPLIED TECHNOLOGY ... Technology Division. Technic31 review of this report was also pro- vided by Messrs. W_ A. Pleasants of Design Integration and Analysis Technical Area

Related Skills in the Marketplace. Final Report.

ERIC Educational Resources Information Center

John C. Calhoun State Community Coll., Decatur, AL.

A study identified related skills needed in five diploma programs offered in the Technical Division of John C. Calhoun State Community College in Decatur, Alabama. The programs were automotive technology, refrigeration/air conditioning, electrical technology, design drafting technology, and cosmetology. Thirty-five area businesses and industries…

Legal Barriers to Educational Technology and Instructional Productivity. Final Report.

ERIC Educational Resources Information Center

Heinich, Robert; Ebert, Kim

A study sought to determine if deterrents to the introduction of certain kinds of educational technology were statutory in nature. The thesis was advanced that educational technology is a threat to the power base of education and the more comprehensive the technology, the greater the threat; therefore the laws and policies setting forth the…

Vinculacion Entre La Educacion Y El Mundo Del Trabajo: Informe Final. (Coloquio Regional Caracas, Venezuela, Septiembre 2-6, 1985) = The Linkage Between Education and Employment: Final Report of the Regional Colloquium (Caracas, Venezuela, September 2-6, 1985).

ERIC Educational Resources Information Center

United Nations Educational, Scientific, and Cultural Organization, Santiago (Chile). Regional Office for Education in Latin America and the Caribbean.

At this regional colloquium 13 papers were presented concerning the relationship between education and employment. Themes addressed were: (1) the transformation of the workplace by technology and science; (2) the future of the disadvantaged population as a consequence of the technological revolution; and (3) the resulting changes in the education…

Work zone intrusion alert technologies : assessment and practical guidance : final report.

DOT National Transportation Integrated Search

2017-06-01

A work zone intrusion alert technology is a type of safety system that is used in a roadway work zone to alert field workers and secure time for them to escape when errant vehicles intrude into the work zone. Although such technologies have potential...

34 CFR 602.3 - What definitions apply to this part?

Code of Federal Regulations, 2013 CFR

2013-07-01

... or clock hours. Distance education means education that uses one or more of the technologies listed... instructor, either synchronously or asynchronously. The technologies may include— (1) The internet; (2) One... any of the technologies listed in paragraphs (1) through (3) of this definition. Final accrediting...

34 CFR 602.3 - What definitions apply to this part?

Code of Federal Regulations, 2014 CFR

2014-07-01

... or clock hours. Distance education means education that uses one or more of the technologies listed... instructor, either synchronously or asynchronously. The technologies may include— (1) The internet; (2) One... any of the technologies listed in paragraphs (1) through (3) of this definition. Final accrediting...

34 CFR 602.3 - What definitions apply to this part?

Code of Federal Regulations, 2012 CFR

2012-07-01

... or clock hours. Distance education means education that uses one or more of the technologies listed... instructor, either synchronously or asynchronously. The technologies may include— (1) The internet; (2) One... any of the technologies listed in paragraphs (1) through (3) of this definition. Final accrediting...

34 CFR 602.3 - What definitions apply to this part?

Code of Federal Regulations, 2010 CFR

2010-07-01

... or clock hours. Distance education means education that uses one or more of the technologies listed... instructor, either synchronously or asynchronously. The technologies may include— (1) The internet; (2) One... any of the technologies listed in paragraphs (1) through (3) of this definition. Final accrediting...

34 CFR 602.3 - What definitions apply to this part?

Code of Federal Regulations, 2011 CFR

2011-07-01

... or clock hours. Distance education means education that uses one or more of the technologies listed... instructor, either synchronously or asynchronously. The technologies may include— (1) The internet; (2) One... any of the technologies listed in paragraphs (1) through (3) of this definition. Final accrediting...

Learning Technology through Three Generations of Technology Enhanced Distance Education Pedagogy

ERIC Educational Resources Information Center

Anderson, Terry; Dron, Jon

2012-01-01

This paper updates earlier work in which we defined three generations of distance education pedagogy. We then describe emerging technologies that are most conducive to instructional designs that evolve with each generation. Finally we discuss matching the pedagogies with learning outcomes. (Contains 3 figures.)

75 FR 10439 - Cognitive Radio Technologies and Software Defined Radios

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-08

... Technologies and Software Defined Radios AGENCY: Federal Communications Commission. ACTION: Final rule. SUMMARY... concerning the use of open source software to implement security features in software defined radios (SDRs... ongoing technical developments in cognitive and software defined radio (SDR) technologies. 2. On April 20...

75 FR 16748 - Final Voluntary Product Standard; DOC PS 20-10 “American Softwood Lumber Standard”

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

... DEPARTMENT OF COMMERCE National Institute of Standards and Technology [Document Number: 090306279...: National Institute of Standards and Technology, Commerce. ACTION: Notice. SUMMARY: The National Institute of Standards and Technology (NIST) announces voluntary product standard DOC PS 20-10 ``American...

Impact of Technologies on Learning in the Workplace. Final Report = L'effet des technologies d'apprentissage sur l'apprentissage a vie en milieu de travail.

ERIC Educational Resources Information Center

Dugas, Tim; Green, Lyndsay; Leckie, Norm

The use of learning technologies in the workplace and their impact on lifelong learning were examined. Data were collected from three sources: the literature on learning technologies and labor market trends affecting the adoption, implementation, and success of learning technologies in the workplace; case studies of 8 Canadian firms with 100 or…

77 FR 49741 - Cranes and Derricks in Construction: Demolition and Underground Construction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-17

... Analysis When it issued the final cranes rule, OSHA prepared a final economic analysis (FEA) as required by... construction and cranes engaged in construction work involving demolition. The FEA for the final cranes..., found that the requirements of the rule were technologically and economically feasible. Because the FEA...

Technology transfer: the key to fusion commercialization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnett, S.C.

1981-01-01

The paper brings to light some of the reasons why technology transfer is difficult in fusion, examines some of the impediments to the process, and finally looks at a successful example of technology transfer. The paper considers some subjective features of fusion - one might call them the sociology of fusion - that are none the less real and that serve as impediments to technology transfer.

The Status of Emerging Technologies: An Economic/Technological Assessment to the Year 2000. Final Report.

ERIC Educational Resources Information Center

Department of Commerce, Washington, DC.

The U.S. Department of Commerce reviewed emerging technologies and their future impact on the economy. This report lists the emerging technologies and suggests their potential contribution to the gross national product by the year 2000. It is based on an assessment by technical experts and agency heads within the Department of Commerce, who…

JPRS Report, Science & Technology, USSR: Materials Science

DTIC Science & Technology

1988-03-15

another. It has developed and transferred to design institutes technological schemes of transportation systems for working deep levels at the Sarbay...manuscript received 1 Oct 84, in final version 19 May 86) pp 45-50 [Article by V.V. Shefel, engineer, Energomontazhproyekt Design -Technological...Institute, Moscow] [Abstract] Three variants of automatic argon-arc welding have been developed at the Energomontazh Design -Technological Institute

New Outcomes: Learning Improvement in Mathematics Integrating Technology - NO LIMIT! An Enhancing Education through Technology Project. Final Report: Years Five and Six (2005-2007)

ERIC Educational Resources Information Center

Popejoy, Kate

2009-01-01

NO LIMIT! (New Outcomes: Learning Improvement in Mathematics Integrating Technology) in Washington state was a six-year initiative originally designed to enhance mathematics teaching and learning in the middle grades through integration of technology, alignment of pedagogical practice with NCTM standards, and strong mentorship of teachers. The…

Hypersonic Flight Test Windows for Technology Development Testing

DTIC Science & Technology

2013-11-01

used. 2.1 Propulsion and Controls Test Window The technologies dealing with scramjet propulsion (inlets, fuel injection, etc.) and hypersonic ...AFRL-RQ-WP-TM-2013-0260 HYPERSONIC FLIGHT TEST WINDOWS FOR TECHNOLOGY DEVELOPMENT TESTING Barry M. Hellman Vehicle Technology Branch...DATES COVERED (From - To) November 2013 Final 01 November 2013 – 25 November 2013 4. TITLE AND SUBTITLE HYPERSONIC FLIGHT TEST WINDOWS FOR

Educational Technology Project, Volume One. The Development of Materials for the Training of Science Education Personnel in Educational Technology. Final Report.

ERIC Educational Resources Information Center

Ziener, George H.; And Others

The planning, production, validation, and revision of learning materials designed for use in institutes for science supervisors is described in this first of five volumes. Four sets of packages, ("Role of the Science Supervisor,""Introduction to Educational Technology,""An Application of Educational Technology," and "Management Kits,") each using…

Survey of Thermoelectric and Solar Technologies as Alternative Energy Solutions

DTIC Science & Technology

2012-02-01

Survey of Thermoelectric and Solar Technologies as Alternative Energy Solutions by Kendall Bianchi, Jay R. Maddux, Kimberly Sablon-Ramsey...Research Laboratory Adelphi, MD 20783-1197 ARL-TR-5920 February 2012 Survey of Thermoelectric and Solar Technologies as Alternative Energy...Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Survey of Thermoelectric and Solar Technologies as Alternative Energy Solutions 5a

Why We All Want It to Work: Towards a Culturally Based Model for Technology and Educational Change

ERIC Educational Resources Information Center

Kerr, Stephen T.

2005-01-01

This paper explores reasons why the use of technology in education may be so attractive to so many people. Two emerging perspectives--memetics, and the social history of technology--are explored, and a typology of technology-as-cultural-tool is presented. Finally, implications of these ideas for educational change are considered.

Survey of Technologies for Monitoring Containment Liners and Covers

EPA Pesticide Factsheets

The report provides information on innovative long-term monitoring technologies to detect contaminant releases beneath a liner containment system and identify potential problems with the integrity of final containment covers.

77 FR 11750 - Idaho: Final Approval of State Underground Storage Tank Program

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... defined under Executive Order 12866. I. National Technology Transfer and Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (``NTTAA''), Public Law 104-113, 12(d... the time needed to review instructions; develop, acquire, install, and utilize technology and systems...

76 FR 57659 - Oregon: Final Approval of State Underground Storage Tank Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-16

... defined under Executive Order 12866. I. National Technology Transfer and Advancement Act Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (``NTTAA''), Public Law 104-113, 12(d... instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting...

Encouraging Learning of Industry Technology: A Merchandising Example

ERIC Educational Resources Information Center

Reilly, Andrew; Huss, Megan; Stoel, Leslie

2005-01-01

The application of the technology acceptance model to a merchandising course teaching industry software was evaluated. Based on technology acceptance research, industry software was presented emphasizing ease-of-use and usefulness. The final course project gave students a quasi real-life experience of combining merchandising skills with the…

Impact of Future Cable Television Technology. Final Summary Report.

ERIC Educational Resources Information Center

Rensselaer Polytechnic Inst., Troy, NY. Telecommunications Research Center.

Technological alternatives in the evolution of present cable television systems into broadband communication networks (BCN) were assessed. Cost estimates were made for alternatives, and the impact of alternatives on BCN development was investigated. An historical study of cable television technology was made which related it to other…

Disabled Access to Technological Advances (DATA) Final Report.

ERIC Educational Resources Information Center

Cress, Cynthia J.

Disabled Access to Technological Advances (DATA) was a 3-year federally funded project to demonstrate how the application of computer technology can increase the employability of severely disabled persons. Services were provided through the integrated efforts of four agencies in Dane County, Wisconsin: an independent living center, a…

Maryland Community Colleges Technology Needs Assessment Survey. Final Technical Report.

ERIC Educational Resources Information Center

Clagett, Craig A.

In 1997, the Maryland Community Colleges Technology Council (MCCTC) undertook a survey of the state's 18 community colleges to assess the status of instructional and administrative technologies and their needs for improvement for the following 5 years. Fifteen-page questionnaires were sent to the colleges requesting information on instructional…

Final Technical Report - Center for Technology for Advanced Scientific Component Software (TASCS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sussman, Alan

2014-10-21

This is a final technical report for the University of Maryland work in the SciDAC Center for Technology for Advanced Scientific Component Software (TASCS). The Maryland work focused on software tools for coupling parallel software components built using the Common Component Architecture (CCA) APIs. Those tools are based on the Maryland InterComm software framework that has been used in multiple computational science applications to build large-scale simulations of complex physical systems that employ multiple separately developed codes.

Virtual Planning at Work: A Tour of NASA Future Flight Central

NASA Technical Reports Server (NTRS)

McClenahen, Jim; Dorighi, Nancy S. (Technical Monitor)

2000-01-01

FutureFlight Central will permit integration of tomorrow's technologies in a risk-free simulation of any airport, airfield, and tower cab environment. The facility provides an opportunity for airlines to mitigate passenger delays by fine tuning airport hub operations, gate management and ramp movement procedures. It also allows airport managers an opportunity to study effects of various improvements at their airports. Finally, it enables air traffic controllers to provide feedback and to become familiar with new airport operations and technologies before final installation.

47 CFR 51.5 - Terms and definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... voice, data, graphics or video telecommunications using any technology. Arbitration, final offer. Final... 1344, Jan. 10, 2000; 65 FR 2550, Jan. 18, 2000; 65 FR 54438, Sept. 8, 2000; 66 FR 43521, Aug. 20, 2001...

Assessment of 25 kW free-piston Stirling technology alternatives for solar applications

NASA Technical Reports Server (NTRS)

Erbeznik, Raymond M.; White, Maurice A.; Penswick, L. B.; Neely, Ronald E.; Ritter, Darren C.; Wallace, David A.

1992-01-01

The final design, construction, and testing of a 25-kW free-piston advanced Stirling conversion system (ASCS) are examined. The final design of the free-piston hydraulic ASCS consists of five subsystems: heat transport subsystem (solar receiver and pool boiler), free-piston hydraulic Stirling engine, hydraulic subsystem, cooling subsystem, and electrical and control subsystem. Advantages and disadvantages are identified for each technology alternative. Technology alternatives considered are gas bearings vs flexure bearings, stationary magnet linear alternator vs moving magnetic linear alternator, and seven different control options. Component designs are generated using available in-house procedures to meet the requirements of the free-piston Stirling convertor configurations.

Permanent certification program for health information technology; revisions to ONC-Approved Accreditor processes. Final rule.

PubMed

2011-11-25

Under the authority granted to the National Coordinator for Health Information Technology by section 3001(c)(5) of the Public Health Service Act (PHSA) as added by the Health Information Technology for Economic and Clinical Health (HITECH) Act, this final rule establishes a process for addressing instances where the ONC-Approved Accreditor (ONC-AA) engages in improper conduct or does not perform its responsibilities under the permanent certification program. This rule also addresses the status of ONC-Authorized Certification Bodies (ONC-ACBs) in instances where there may be a change in the accreditation organization serving as the ONC-AA and clarifies the responsibilities of the new ONC-AA.

International Space Station (ISS)

NASA Image and Video Library

1994-09-21

Artist's concept of the final configuration of the International Space Station (ISS) Alpha. The ISS is a multidisciplinary laboratory, technology test bed, and observatory that will provide an unprecedented undertaking in scientific, technological, and international experimentation.

Solutions to microplastic pollution - Removal of microplastics from wastewater effluent with advanced wastewater treatment technologies.

PubMed

Talvitie, Julia; Mikola, Anna; Koistinen, Arto; Setälä, Outi

2017-10-15

Conventional wastewater treatment with primary and secondary treatment processes efficiently remove microplastics (MPs) from the wastewater. Despite the efficient removal, final effluents can act as entrance route of MPs, given the large volumes constantly discharged into the aquatic environments. This study investigated the removal of MPs from effluent in four different municipal wastewater treatment plants utilizing different advanced final-stage treatment technologies. The study included membrane bioreactor treating primary effluent and different tertiary treatment technologies (discfilter, rapid sand filtration and dissolved air flotation) treating secondary effluent. The MBR removed 99.9% of MPs during the treatment (from 6.9 to 0.005 MP L -1 ), rapid sand filter 97% (from 0.7 to 0.02 MP L -1 ), dissolved air flotation 95% (from 2.0 to 0.1 MP L -1 ) and discfilter 40-98.5% (from 0.5 - 2.0 to 0.03-0.3 MP L -1 ) of the MPs during the treatment. Our study shows that with advanced final-stage wastewater treatment technologies WWTPs can substantially reduce the MP pollution discharged from wastewater treatment plants into the aquatic environments. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Impact of Numerical Control Technology and Computer Aided Manufacturing on Curriculum Development in Industrial Education and Technology. A Final Report.

ERIC Educational Resources Information Center

Bauch, Klaus Dieter

The study was designed to investigate the effects of Numerical Control Technology and Computer-Aided Manufacturing (NC/CAM) in American industry on industrial education and engineering technology education. The specific purpose was to identify a data base and rationale for curriculum development in NC/CAM through a comparison of views by…

Advanced Authoring Technologies, Capabilities and Opportunities (Technologies avancees d’authoring, possibilites et opportunites)

DTIC Science & Technology

2011-02-01

NORTH ATLANTIC TREATY ORGANISATION RESEARCH AND TECHNOLOGY ORGANISATION AC/323(HFM-129)TP/349 www.rto.nato.int RTO TECHNICAL REPORT TR...Final Report of Task Group HFM-129. Published February 2011 Distribution and Availability on Back Cover...NORTH ATLANTIC TREATY ORGANISATION RESEARCH AND TECHNOLOGY ORGANISATION AC/323(HFM-129)TP/349 www.rto.nato.int RTO TECHNICAL REPORT TR-HFM

Detection technology for IVHS : Volume I: Final Report

DOT National Transportation Integrated Search

1996-12-01

The Detection Technology for the IVHS project identified traffic parameters and their required accuracies for characterizing traffic flow in conventional and newer intelligent transportation systems (ITS); obtained state-of-the-art detectors and inst...

Federal Highway Administration research and technology evaluation final report : Eco-Logical

DOT National Transportation Integrated Search

2018-03-01

This report documents an evaluation of Federal Highway Administrations (FHWA) Research and Technology Programs activities on the implementation of the Eco-Logical approach by State transportation departments and metropolitan planning organizati...

Probability of detection evaluation results for railroad tank car nondestructive testing : final report.

DOT National Transportation Integrated Search

2016-08-01

The Federal Railroad Administration (FRA), Transportation Technology Center, Inc. (TTCI), and rail industry participants have : performed probability of detection (POD) assessments to evaluate nondestructive testing (NDT) technologies, which are : pr...

Application placement technologies for vegetation management on North Carolina roadsides : final report.

DOT National Transportation Integrated Search

2007-05-30

Research experiments were designed and initiated to determine if application placement technologies offer : a viable solution for vegetation management along North Carolina Roadsides. Select equipment was evaluated for : broomsedge (Andropogon virgin...

Nabisco Foods Division--"New Indy" Workplace Literacy Project. Final Performance Report.

ERIC Educational Resources Information Center

Ivy Tech State Coll., Indianapolis, IN.

This document contains a final report, evaluation, and curriculum materials from a project conducted at the RJR Nabisco plant in Indianapolis to upgrade the literacy and numeracy skills of the workers to facilitate technological changes to production lines. As the final report explains, although the goal of the project was to recruit and test 150…

76 FR 7852 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from BWX Technologies, Inc...

78 FR 54960 - Approval and Promulgation of Air Quality Implementation Plans; Massachusetts; Reasonably...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-09

... requirements of Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272... Technology for the 1997 8- Hour Ozone Standard AGENCY: Environmental Protection Agency (EPA). ACTION: Final... reasonably available control technology (RACT) for oxides of nitrogen (NO X ) and volatile organic compounds...

Ink Jet Printing for Silicon Photovoltaics: Cooperative Research and Development Final Report, CRADA Number CRD-04-00139

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ginley, D. S.

2010-08-01

The purpose of this CRADA was to combine the strengths of NREL and Evergreen Solar in the area of ink jet printing to develop a new manufacturing technology necessary to produce Si solar cells based on ribbon technology comparable to or exceeding current technologies.

The Training and Technology Project Experimental Research Program for Vocational-Technical Teachers. Final Report.

ERIC Educational Resources Information Center

Merrill, E.L.; Russell, Wendell H.

Over a 31-month period from June 1966 to December 1968, the University of Tennessee and Union Carbide Corporation conducted preservice and inservice institutes for 160 industrial education teachers. These institutes carried college credit and covered Mechanical Technology and Drafting, Industrial Electronics Technology, Machine Shop and…

Development of a Curriculum in Laser Technology. Final Report.

ERIC Educational Resources Information Center

Wasserman, William J.

A Seattle Central Community College project visited existing programs, surveyed need, and developed a curriculum for a future program in Laser-Electro-Optics (LEO) Technology. To establish contacts and view successful programs, project staff made visits to LEO technology programs at San Jose City College and Texas State Technical Institute, Center…

Final Report on the Performance of the Eichrom Technologies Procept® Rapid Dioxin Assay for Soil and Sediment Samples

EPA Science Inventory

A demonstration of screening technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under the U.S. Environmental Protection Agency’s (EPA’s) Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in 2004. ...

Nuclear Medical Technology. Curriculum for a Two Year Program. Final Report.

ERIC Educational Resources Information Center

Buatti, A.; Rich, D.

Objectives of the project briefly described here were (1) to develop curriculum for a two-year nuclear medical technology program based on a working relationship between three institutions (community college, university health center, and hospital) and (2) to develop procedures for the operation of a medical imaging and radiation technology core…

Workshop on Science and Technology Education and Productive Work. Final Report.

ERIC Educational Resources Information Center

Ministry of Education, Addis Ababa (Ethiopia).

This workshop was organized as a contribution to Ethiopia's human resettlement activities necessitated by the recurrent drought. The objectives of the workshop were to: (1) appraise the relevance of basic rural technologies and identify modalities of their application; (2) develop materials in the fields of biotechnology and basic technology; (3)…

Environmental Technology (Laboratory Analysis and Environmental Sampling) Curriculum Development Project. Final Report.

ERIC Educational Resources Information Center

Hinojosa, Oscar V.; Guillen, Alfonso

A project assessed the need and developed a curriculum for environmental technology (laboratory analysis and environmental sampling) in the emerging high technology centered around environmental safety and health in Texas. Initial data were collected through interviews by telephone and in person and through onsite visits. Additional data was…

The Challenges and Opportunities of Wireless Technologies in the Classroom: Related Standards and Regulations

ERIC Educational Resources Information Center

Oriaku, Ngozi

2008-01-01

Wireless technologies have revolutionized the ways teaching and learning have become in many colleges and universities. It is therefore interesting to observe the way wireless technologies are used to organize small group meetings. It provides online access to internet resources such as instructor lecture series. It finally helps in…

Final report on the maintenance asset management project : phase II.

DOT National Transportation Integrated Search

2013-07-01

Iowa Department of Transportation (IA DOT) is finalizing research to streamline field inventory/inspection of culverts by Maintenance and Construction staff while maximizing the use of tablet technologies. The project began in 2011 to develop some ne...

Cooperative agreement # RITARS-14-H-HOU : final report.

DOT National Transportation Integrated Search

2016-07-15

The University of Houston, in partnership with the Gas Technology Institute, and with support from the : Commercial Remote Sensing & Spatial Technologies Program at the U.S. Department of Transportation : undertook a pilot project to mitigate pipelin...

Publicly Owned Treatment Works (POTW): NESHAP Risk and Technology Review Final

EPA Pesticide Factsheets

These proposed amendments to the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Publicly Owned Treatment Works (POTW) result from the results of the residual risk and technology review of that source category.

Alabama warm mix asphalt field study : final report.

DOT National Transportation Integrated Search

2010-05-01

The Alabama Department of Transportation hosted a warm mix asphalt field demonstration in August 2007. The warm mix asphalt technology demonstrated was Evotherm Dispersed Asphalt Technology. The WMA and hot mix asphalt produced for the demonstration ...

Rural public transportation technologies : user needs and applications : final report

DOT National Transportation Integrated Search

1998-07-01

The Rural Public Transportation Technologies: User Needs and Applications study was conducted as part of the U.S. Department of Transportations (DOT) overall Rural Intelligent Transportation System (ITS) Program. The study examined the opportuniti...

Broadband Optical Access Technologies to Converge towards a Broadband Society in Europe

NASA Astrophysics Data System (ADS)

Coudreuse, Jean-Pierre; Pautonnier, Sophie; Lavillonnière, Eric; Didierjean, Sylvain; Hilt, Benoît; Kida, Toshimichi; Oshima, Kazuyoshi

This paper provides insights on the status of broadband optical access market and technologies in Europe and on the expected trends for the next generation optical access networks. The final target for most operators, cities or any other player is of course FTTH (Fibre To The Home) deployment although we can expect intermediate steps with copper or wireless technologies. Among the two candidate architectures for FTTH, PON (Passive Optical Network) is by far the most attractive and cost effective solution. We also demonstrate that Ethernet based optical access network is very adequate to all-IP networks without any incidence on the level of quality of service. Finally, we provide feedback from a FTTH pilot network in Colmar (France) based on Gigabit Ethernet PON technology. The interest of this pilot lies on the level of functionality required for broadband optical access networks but also on the development of new home network configurations.

Testing technology. A Sandia Technology Bulletin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goetsch, B.; Floyd, H.L.; Doran, L.

1994-02-01

This Sandia publication seeks to facilitate technology exchange with industries, universities, and government agencies. It presents brief highlights of four projects. First is a project to simulate the use of airbags to soften the landing of a probe on Mars. Second is the use of a computer simulation system to facilitate the testing of designs for different experiments, both for experimental layout and results analysis. Third is the development of a system for in-house testing of batteries and capacitive energy storage systems, for deployment at the manufacturing sites, as opposed to final use areas. Finally is information on a noncontactmore » measurement system which can be used to determine axes on objects of different shapes, with high precision.« less

Point of Injury Sampling Technology for Battlefield Molecular Diagnostics

DTIC Science & Technology

2011-11-14

Injury" Sampling Technology for Battlefield Molecular Diagnostics November 14, 2011 Sponsored by Defense Advanced Research Projects Agency (DOD...Date of Contract: April 25, 2011 Short Title of Work: "Point of Injury" Sampling Technology for Battlefield Molecular Diagnostics " Contract...PHASE I FINAL REPORT: Point of Injury, Sampling Technology for Battlefield Molecular Diagnostics . W31P4Q-11-C-0222 (UNCLASSIFIED) P.I: Bernardo

Engineering Related Technology: A Laboratory and Curriculum Design for the Newly Emerging Technology of Pollution-Corrosion Measurement and Control. Final Report.

ERIC Educational Resources Information Center

Shields, F. K.; And Others

In order to meet the educational needs for a separate curriculum at the secondary level for technological training related to pollution and corrosion measurement and control, a 3-year, 1080-hour vocational program was developed for use in an area vocational high school. As one of four programs in the technology careers area, this curriculum design…

"Un"complicated Technologies and Erstwhile Aids: How PowerPoint, the Internet, and Political Cartoons Can Elicit Engagement and Challenge Thinking in New Ways

ERIC Educational Resources Information Center

Bickford, J. H., III

2010-01-01

This paper is based on three beliefs. First, technology can engage and challenge students' thinking. Second, technology can assist students in creating quality work. Finally, computer-generated student-work can be used as educational tools in productive ways that other student-work cannot. This article suggests new ways to use old technologies to…

Empirical study of the perceived ease of use and relative advantage on load-bearing masonry (LBM) technology adoption

NASA Astrophysics Data System (ADS)

Ramli, Nor Azlinda; Abdullah, Che Sobry; Nawi, Mohd Nasrun Mohd

2017-11-01

Load-bearing masonry (LBM) technology has been identified as an alternative method that can potentially encourage the sustainability of the housing industry. The adoption of LBM technology is believed to bring beneficial effects to the housing industry as well as company productivity. The factors related to the adoption LBM technology was revealed to strongly influence the implementation of this system in the housing industry. The aim of this study is to determine the factors influencing the adoption of LBM technology among the developer firms in Malaysia as well as the factors that are highly related to perceived ease of use and relative advantage. A random sampling technique was applied and a questionnaire-based field survey was carried out to obtain the data from the respondents. All the data were analyzed using Partial Least Squares Structural Equation Modeling (PLS-SEM). The findings of this paper have revealed that perceived ease of use and relative advantage are related to the adoption of LBM technology. The findings also indicated the validity of Technology Acceptance Model TAM (perceived ease of use) and Innovation Diffusion Theory IDT (relative advantage) as the determinant factors in the adoption of LBM technology. Finally, some recommendations for future research are suggested in the final section of this paper.

Knowledge-based systems in Japan

NASA Technical Reports Server (NTRS)

Feigenbaum, Edward; Engelmore, Robert S.; Friedland, Peter E.; Johnson, Bruce B.; Nii, H. Penny; Schorr, Herbert; Shrobe, Howard

1994-01-01

This report summarizes a study of the state-of-the-art in knowledge-based systems technology in Japan, organized by the Japanese Technology Evaluation Center (JTEC) under the sponsorship of the National Science Foundation and the Advanced Research Projects Agency. The panel visited 19 Japanese sites in March 1992. Based on these site visits plus other interactions with Japanese organizations, both before and after the site visits, the panel prepared a draft final report. JTEC sent the draft to the host organizations for their review. The final report was published in May 1993.

ATP Interior Noise Technology and Flight Demonstration Program

NASA Technical Reports Server (NTRS)

Stephens, David G.; Powell, Clemans A.

1988-01-01

The paper provides an overview of the ATP (Advanced Turboprop Program) acoustics program with emphasis on the NASA technology program and the recent NASA/Industry demonstration programs aimed at understanding and controlling passenger cabin noise. Technology developments in propeller (source) noise, cabin noise transmission, and subjective acoustics are described. Finally, an overview of the industry demonstrator programs is presented.

Vocational-Technical Education Interface with Ohio's High Technology Business and Industrial Sector. Final Report.

ERIC Educational Resources Information Center

McCormick, Robert W.

This study explored the relationship of vocational-technical educational institutions in Ohio with business and industry using high-technology applications. The study attempted to determine what high-technology applications will be adopted by Ohio's business and industry in the next 5 years, what experience the schools have had in working with…

New Information Technology Directions for American Education. Improving Science and Mathematics Education. Final Report.

ERIC Educational Resources Information Center

Melmed, Arthur S.; Burnham, Robert A.

This report is an analysis of the findings of four workshops exploring the ways interactive technology can be considered an option for improving American education after 25 years of research and development. Sections include: (1) "Manpower Needs and School Problems"; (2) "Science and Technology Option"; (3) "Barriers and Strategy"; and (4) "To…

Spring 2004 Industry Study Final Report: Strategic Materials

DTIC Science & Technology

2004-01-01

decreasing processing costs. Processing costs can be reduced by using powder metallurgy technology to reduce waste and by seeking new markets to... market share is likely to remain fierce until the arrival of the next miniaturization technology , nanoelectromechanical system (NEMS). Smart...the transportation, medical, energy, information technology , and environmental industries will create the strongest economic pull for the

Facility Planning for 21st Century. Technology, Industry, and Education.

ERIC Educational Resources Information Center

Hill, Franklin

When the Orange County School Board (Orlando, Florida) decided to build a new high school, they recognized Central Florida's high technology emphasis as a special challenge. The new facility needed to meet present instructional demands while being flexible enough to incorporate 21st century technologies. The final result is a new $30 million high…

Implications of Information Technology for Employment, Skills, and Wages: A Review of Recent Research. Final Report

ERIC Educational Resources Information Center

Handel, Michael J.

2003-01-01

This paper provides an extensive review of the research literature on the effects of information technology (IT) on employment levels, job skill requirements, and wages. The first sections provide historical background on earlier waves of concern regarding automation, contemporary public opinion regarding new workplace technology, and trends in…

Using Technology to Explore Mathematical Relationships: A Framework for Orienting Mathematics Courses for Prospective Teachers

ERIC Educational Resources Information Center

Bowers, Janet S.; Stephens, Becky

2011-01-01

The technological revolution that has finally permeated K-12 education has direct implications for modern teacher educators whose "Hippocratic oath" is to best prepare future teachers for twenty-first-century classrooms. The goal of this article is to suggest that the heart of sound technological implementation is to encourage students to use…

Manual for research, development and technology program and project evaluations : final report.

DOT National Transportation Integrated Search

2016-04-01

This manual provides the Federal Railroad Administrations (FRA) Office of Research, Development and Technology (RD&T) a : framework, standards, and procedures for planning, conducting, reporting, and using sound evaluations of RD&Ts projects fo...

Electric vehicle charging technologies analysis and standards : final research project report.

DOT National Transportation Integrated Search

2017-02-01

This project has evaluated the technologies and standards associated with Electric : Vehicle Service Equipment (EVSE) and the related infrastructure, and the major cost : issue related to electric vehicle (EV) charging -- the cost of utility power. T...

Status of the transportation technology center - 2015 : final report.

DOT National Transportation Integrated Search

2016-03-01

The Transportation Technology Center (TTC) is a Federally owned, privately operated test facility in Colorado. It has over 50 : miles of test track arranged in different configurations for testing all aspects of vehicle-track interaction. Maximum tes...

Socio-Economic Impact Assessment of Automated Transit Information Systems Technology

DOT National Transportation Integrated Search

1984-03-01

This report is the final product of a program to assess the socio-economic impacts of automated transit information system (ATIS) technology deployments on the transit industry's telephone information/marketing function. In the course of this program...

SmartPark Technology Demonstration Project, Phase II: Final Report : Technology Brief

DOT National Transportation Integrated Search

2018-05-01

In 2000, the National Transportation Safety Board recommended that the Federal Motor Carrier Safety Administration (FMCSA) create a guide to inform truck drivers about locations and availability of parking. In 2002, the Federal Highway Administration...

Rural Public Transportation Technologies: User Needs and Applications. Final Report

DOT National Transportation Integrated Search

1998-08-01

The Rural Public Transportation Technologies: User Needs and Applications Study was conducted as part of the U.S. DOT's overall Rural Intelligent Transportation System (ITS) Program. The study examined the opportunities and challenges of planning and...

Vehicle telematics as a platform for road use fees : final report.

DOT National Transportation Integrated Search

2016-11-01

Vehicle telematics systems are composed of various onboard communications, positioning technologies, and computing technologies. Much of the data generated and/or gathered by these systems can be used to determine travel. These systems enable a range...

NASA's Long-range Technology Goals

NASA Technical Reports Server (NTRS)

1990-01-01

This document is part of the Final Report performed under contract NASW-3864, titled "NASA's Long-Range Technology Goals". The objectives of the effort were: To identify technologies whose development falls within NASA's capability and purview, and which have high potential for leapfrog advances in the national industrial posture in the 2005-2010 era. To define which of these technologies can also enable quantum jumps in the national space program. To assess mechanisms of interaction between NASA and industry constituencies for realizing the leapfrog technologies. This Volume details the findings pertaining to the advanced space-enabling technologies.

In-Space Propulsion (ISP) Solar Sail Propulsion Technology Development

NASA Technical Reports Server (NTRS)

Montgomery, Edward E., IV

2004-01-01

An overview of the rationale and content for Solar Sail Propulsion (SSP), the on-going project to advance solar technology from technology readiness level 3 to 6 will be provided. A descriptive summary of the major and minor component efforts underway will include identification of the technology providers and a listing of anticipated products Recent important results from major system ground demonstrators will be provided. Finally, a current status of all activities will provided along with the most recent roadmap for the SSP technology development program.

ILEWG technology roadmap for Moon exploration

NASA Astrophysics Data System (ADS)

Foing, Bernard H.

2008-04-01

We discuss the charter and activities of the International Lunar Exploration Working Group (ILEWG), and give an update from the related ILEWG task groups. We discuss the different rationale and technology roadmap for Moon exploration, as debated in previous ILEWG conferences. The Technology rationale includes: 1) The advancement of instrumentation: 2) Technologies in robotic and human exploration 3) Moon-Mars Exploration can inspire solutions to global Earth sustained development. We finally discuss a possible roadmap for development of technologies necessary for Moon and Mars exploration.

A Systematic Method of Integrating BIM and Sensor Technology for Sustainable Construction Design

NASA Astrophysics Data System (ADS)

Liu, Zhen; Deng, Zhiyu

2017-10-01

Building Information Modeling (BIM) has received lots of attention of construction field, and sensor technology was applied in construction data collection. This paper developed a method to integrate BIM and sensor technology for sustainable construction design. A brief literature review was conducted to clarify the current development of BIM and sensor technology; then a systematic method for integrating BIM and sensor technology to realize sustainable construction design was put forward; finally a brief discussion and conclusion was given.

77 FR 61750 - Application for Final Commitment for a Long-Term Loan or Financial Guarantee in Excess of $100...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-11

... Suppliers: Boeing Space and Intelligence Systems, Space Exploration Technologies Corp., Aon plc. Obligor... for final commitment for a long-term loan or financial guarantee in excess of $100 million. Reason for...

Hazardous material transportation safety and security field operational test final detailed test plans : executive summary

DOT National Transportation Integrated Search

2003-09-16

The objective of this Hazardous Material (HazMat) Transportation Safety and Security Field Operational Test (FOT) Final Detailed Test Plans evaluation is to measure the impact of technology solutions on the safety, security, and operational efficienc...

40 CFR 57.813 - Final decision.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Final decision. 57.813 Section 57.813 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PRIMARY NONFERROUS SMELTER ORDERS Waiver of Interim Requirement for Use of Continuous Emission Reduction Technology...

Pre-Launch Radiometric Performance Characterization of the Advanced Technology Microwave Sounder on the Joint Polar Satellite System-1 Satellite

NASA Technical Reports Server (NTRS)

Smith, Craig K.; Kim, Edward; Leslie, R. Vincent; Lyu, Joseph; McCormick, Lisa M.; Anderson, Kent

2017-01-01

The Advanced Technology Microwave Sounder (ATMS) is a space-based, cross-track radiometer for operational atmospheric temperature and humidity sounding, utilizing 22 channels over a frequency range from 23 to 183 gigahertz. The ATMS for the Joint Polar Satellite System-1 has undergone two rounds of re-work in 2014-2015 and 2016, following performance issues discovered during and following thermal vacuum chamber (TVAC) testing at the instrument and observatory level. Final shelf-level testing, including measurement of pass band characteristics and spectral response functions, was completed in December 2016. Final instrument-level TVAC testing and calibration occurred during February 2017. Here we will describe the instrument-level TVAC calibration process, and illustrate with results from the final TVAC calibration effort.

The Use of Mobile Technologies to Assist with Life Skills/Independence of Students with Moderate/Severe Intellectual Disability and/or Autism Spectrum Disorders: Considerations for the Future of School Psychology

ERIC Educational Resources Information Center

Ayres, Kevin Michael; Mechling, Linda; Sansosti, Frank J.

2013-01-01

To successfully integrate technology into any educational program, practitioners need awareness of available technology, an understanding of how it can assist with instruction, knowledge of ways it can support day-to-day activities and, finally, the ability to teach students as well as educators to use the technology. The proliferation of advanced…

78 FR 70567 - Nationwide Use of High Frequency and Ultra High Frequency Active SONAR Technology; Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-26

... such as: The attacks of September 11, 2001; natural disasters such as Hurricanes Katrina and Rita of... UHF SONAR technology during times of extreme weather, such as hurricanes, could be required for...

SELENIUM TREATMENT/REMOVAL ALTERNATIVES DEMONSTRATION PROJECT - MINE WASTE TECHNOLOGY PROGRAM ACTIVITY III, PROJECT 20

EPA Science Inventory

This document is the final report for EPA's Mine WAste Technology Program (MWTP) Activity III, Project 20--Selenium Treatment/Removal Alternatives Demonstration project. Selenium contamination originates from many sources including mining operations, mineral processing, abandoned...

U35: Legacy Engine Final Report

DOT National Transportation Integrated Search

2012-07-01

The Legacy engine is a new core technology that can be used with existing infrastructure providing for near term benefits while minimizing costs. Also, as a new technology, it will be optimized for many years to come providing the opportunity for con...

Advanced Crash Avoidance Technologies (ACAT) Program - Final Report of the GM-VTTI Backing Crash Countermeasures Project

DOT National Transportation Integrated Search

2011-08-01

The Backing crash Countermeasures project, part of the U.S. Department of Transportation's Advanced Crash Avoidance Technologies (ACAT) program, developed a basic methodological framework and computerbased simulation model to estimate the effectiv...

Active Work Zone Safety Using Emerging Technologies : Final Report

DOT National Transportation Integrated Search

2017-07-01

The major objectives of this research were to (1) identify technologies that can be used in real time to detect a hazardous proximity situation between construction equipment and pedestrian workers and provide an appropriate warning; (2) develop a Bl...

The effect of technology on student science achievement

NASA Astrophysics Data System (ADS)

Hilton, June Kraft

2003-10-01

Prior research indicates that technology has had little effect on raising student achievement. Little empirical research exists, however, studying the effects of technology as a tool to improve student achievement through development of higher order thinking skills. Also, prior studies have not focused on the manner in which technology is being used in the classroom and at home to enhance teaching and learning. Empirical data from a secondary school representative of those in California were analyzed to determine the effects of technology on student science achievement. The quantitative analysis methods for the school data study included a multiple linear path analysis, using final course grade as the ultimate exogenous variable. In addition, empirical data from a nationwide survey on how Americans use the Internet were disaggregated by age and analyzed to determine the relationships between computer and Internet experience and (a) Internet use at home for school assignments and (b) more general computer use at home for school assignments for school age children. Analysis of data collected from the a "A Nation Online" Survey conducted by the United States Census Bureau assessed these relationships via correlations and cross-tabulations. Finally, results from these data analyses were assessed in conjunction with systemic reform efforts from 12 states designed to address improvements in science and mathematics education in light of the Third International Mathematics and Science Survey (TIMSS). Examination of the technology efforts in those states provided a more nuanced understanding of the impact technology has on student achievement. Key findings included evidence that technology training for teachers increased their use of the computer for instruction but students' final science course grade did not improve; school age children across the country did not use the computer at home for such higher-order cognitive activities as graphics and design or spreadsheets/databases; and states whose systemic reform initiatives included a mix of capacity building and alignment to state standards realized improved student achievement on the 2000 NAEP Science Assessment.

Developing an instrument for assessing students' concepts of the nature of technology

NASA Astrophysics Data System (ADS)

Liou, Pey-Yan

2015-05-01

Background:The nature of technology has been rarely discussed despite the fact that technology plays an essential role in modern society. It is important to discuss students' concepts of the nature of technology, and further to advance their technological literacy and adaptation to modern society. There is a need to assess high school students' concepts of the nature of technology. Purpose:This study aims to engage in discourse on students' concepts of the nature of technology based on a proposed theoretical framework. Moreover, another goal is to develop an instrument for measuring students' concepts of the nature of technology. Sample:Four hundred and fifty-five high school students' perceptions of technology were qualitatively analyzed. Furthermore, 530 students' responses to a newly developed questionnaire were quantitatively analyzed in the final test. Design and method:First, content analysis was utilized to discuss and categorize students' statements regarding technology and its related issues. The Student Concepts of the Nature of Technology Questionnaire was developed based on the proposed theoretical framework and was supported by the students' qualitative data. Finally, exploratory factor analysis and reliability analysis were applied to determine the structure of the items and the internal consistency of each scale. Results:Through a process of instrument development, the Student Concepts of the Nature of Technology Questionnaire was shown to be a valid and reliable tool for measuring students' concepts of the nature of technology. This newly developed questionnaire is composed of 29 items in six scales, namely 'technology as artifacts,' 'technology as an innovation change,' 'the current role of technology in society,' 'technology as a double-edged sword,' 'technology as a science-based form,' and 'history of technology.' Conclusions:The Student Concepts of the Nature of Technology Questionnaire has been confirmed as a reasonably valid and reliable instrument. This study provides a useful questionnaire for educational researchers and practitioners for measuring students' concepts of the nature of technology.

Medicare and state health care programs: fraud and abuse; safe harbors for certain electronic prescribing and electronic health records arrangements under the anti-kickback statute. Final rule.

PubMed

2006-08-08

As required by the Medicare Prescription Drug, Improvement, and Modernization Act of 2003 (MMA), Public Law 108-173, this final rule establishes a new safe harbor under the Federal anti-kickback statute for certain arrangements involving the provision of electronic prescribing technology. Specifically, the safe harbor would protect certain arrangements involving hospitals, group practices, and prescription drug plan (PDP) sponsors and Medicare Advantage (MA) organizations that provide to specified recipients certain nonmonetary remuneration in the form of hardware, software, or information technology and training services necessary and used solely to receive and transmit electronic prescription information. In addition, in accordance with section 1128B(b)(3)(E) of the Social Security Act (the Act), this final rule creates a separate new safe harbor for certain arrangements involving the provision of nonmonetary remuneration in the form of electronic health records software or information technology and training services necessary and used predominantly to create, maintain, transmit, or receive electronic health records.

Adapting Strategic Aircraft Assets to a Changing World: Technology Insertion to Provide Flexibility

DTIC Science & Technology

1994-09-01

Distributed Processing ............................ 67 Unembedded Expansions ............................ 71 Concepts for, and Impacts on, Preflight...capabilities through the use of unembedded expansions to the existing avionics complex. But, before we explore these technology insertion concepts, we must... Unembedded Expansions The final hardware technology insertion area focuses on the concept of expanding the aircraft’s capabilities by inserting, or perhaps

Innovations for Federal Service: A Study of Innovative Technologies for Federal Government Services to Older Americans and Consumers. Final Report.

ERIC Educational Resources Information Center

Harris, John; And Others

This document focuses on technologies that can be used to improve federal government services. Reference Point, a foundation based in New Jersey, was chosen by the Office of Technology Assessment of the U.S. Congress to study the application of advanced information. The applications selected for the study were: Electronic Information…

Efficient Computational Prototyping of Mixed Technology Microfluidic Components and Systems

DTIC Science & Technology

2002-08-01

AFRL-IF-RS-TR-2002-190 Final Technical Report August 2002 EFFICIENT COMPUTATIONAL PROTOTYPING OF MIXED TECHNOLOGY MICROFLUIDIC...SUBTITLE EFFICIENT COMPUTATIONAL PROTOTYPING OF MIXED TECHNOLOGY MICROFLUIDIC COMPONENTS AND SYSTEMS 6. AUTHOR(S) Narayan R. Aluru, Jacob White...Aided Design (CAD) tools for microfluidic components and systems were developed in this effort. Innovative numerical methods and algorithms for mixed

Disseminating and Replicating an Effective Emerging Literacy Technology Curriculum: A Final Report

ERIC Educational Resources Information Center

Hutinger, Patricia; Bell, Carol; Daytner, Gary; Johanson, Joyce

2005-01-01

Emerging Literacy Technology Curriculum (ELiTeC 2, [referred to as E2 in this report]), housed at the Center for Best Practices in Early Childhood at Western Illinois University, was funded in 2000 by the U.S. Department of Education's Office of Special Education Programs (OSEP) as a 3-year Phase 3 Steppingstones of Technology Research on…

Methods for Predicting and Assessing the Impact of Technology on Human Resource Parameters: Report of the Literature. Final Report.

ERIC Educational Resources Information Center

Potter, Norman R.; Dieterly, Duncan L.

The literature review was undertaken to establish the current status of the methodology for forecasting and assessing technology and for quantizing human resource parameters with respect to the impact of incoming technologies. The review of 140 selected documents applicable to the study was undertaken with emphasis on the identification of methods…

Development of vehicle magnetic air conditioner (VMAC) technology. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gschneidner, Karl A., Jr.; Pecharsky, V.K.; Jiles, David

2001-08-28

The objective of Phase I was to explore the feasibility of the development of a new solid state refrigeration technology - magnetic refrigeration - in order to reduce power consumption of a vehicle air conditioner by 30%. The feasibility study was performed at Iowa State University (ISU) together with Astronautics Corporation of America Technology Center (ACATC), Madison, WI, through a subcontract with ISU.

Operational Leadership and Advancing Technology

DTIC Science & Technology

2009-05-04

FINAL 3. DATES COVERED (From - To) 9 Feb – 4 May 2009 4. TITLE AND SUBTITLE Operational Leadership and Advancing Technology 5a...operational leader must use his authority and leadership skills to get by in from all concerned to maximize technological advances. 15. SUBJECT TERMS...WWI armor, British armor doctrine, German Armor doctrine, operational leadership 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT

Case Analysis Of The Joint High Speed Vessel Program: Defense Acquisition

DTIC Science & Technology

2016-09-01

reviews resulted in a series of Advanced Concept Technology Demonstrations (ACTD) designed to explore the military utility of converted commercial...requirements into a final and unique materiel solution for a system capability that is fielded. 14. SUBJECT TERMS Advanced Concept and Technology ...Advanced Concept Technology Demonstrations (ACTD) designed to explore the military utility of converted commercial, high-speed, shallow-draft

Evaluation of a Teacher Technology Training Program for Elementary Teachers in a Private School Setting: An Action-Oriented Dissertation

ERIC Educational Resources Information Center

Bankirer, Nathaniel

2018-01-01

While teachers recognize the importance of technology integration into the classroom, they require training, support, and resources to do so effectively. This action research dissertation focuses on the resources necessary to provide teacher technology training at a private elementary school. It reports on the final evaluation stage of the…

Designing for Diverse Learning: Case Study of Place-Based Learning in Design and Technologies Pre-Service Teacher Education

ERIC Educational Resources Information Center

Best, Marnie; MacGregor, Denise; Price, Deborah

2017-01-01

Place-based learning experiences in Design and Technologies education connect people and place with design processes and products. Drawing on place-based learning, this case study shares the experiences of eight final year pre-service Design and Technologies education students from the University of South Australia as they collaborated with…

Sustainability assessment of tertiary wastewater treatment technologies: a multi-criteria analysis.

PubMed

Plakas, K V; Georgiadis, A A; Karabelas, A J

2016-01-01

The multi-criteria analysis gives the opportunity to researchers, designers and decision-makers to examine decision options in a multi-dimensional fashion. On this basis, four tertiary wastewater treatment (WWT) technologies were assessed regarding their sustainability performance in producing recycled wastewater, considering a 'triple bottom line' approach (i.e. economic, environmental, and social). These are powdered activated carbon adsorption coupled with ultrafiltration membrane separation (PAC-UF), reverse osmosis, ozone/ultraviolet-light oxidation and heterogeneous photo-catalysis coupled with low-pressure membrane separation (photocatalytic membrane reactor, PMR). The participatory method called simple multi-attribute rating technique exploiting ranks was employed for assigning weights to selected sustainability indicators. This sustainability assessment approach resulted in the development of a composite index as a final metric, for each WWT technology evaluated. The PAC-UF technology appears to be the most appropriate technology, attaining the highest composite value regarding the sustainability performance. A scenario analysis confirmed the results of the original scenario in five out of seven cases. In parallel, the PMR was highlighted as the technology with the least variability in its performance. Nevertheless, additional actions and approaches are proposed to strengthen the objectivity of the final results.

SNAP-8 electrical generating system development program

NASA Technical Reports Server (NTRS)

1971-01-01

The SNAP-8 program has developed the technology base for one class of multikilowatt dynamic space power systems. Electrical power is generated by a turbine-alternator in a mercury Rankine-cycle loop to which heat is transferred and removed by means of sodium-potassium eutectic alloy subsystems. Final system overall criteria include a five-year operating life, restartability, man rating, and deliverable power in the 90 kWe range. The basic technology was demonstrated by more than 400,000 hours of major component endurance testing and numerous startup and shutdown cycles. A test system, comprised of developed components, delivered up to 35 kWe for a period exceeding 12,000 hours. The SNAP-8 system baseline is considered to have achieved a level of technology suitable for final application development for long-term multikilowatt space missions.

10 CFR 603.900 - Receipt of final performance report.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Receipt of final performance report. 603.900 Section 603.900 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS Award Terms Related to Other Administrative Matters Financial and Programmatic Reporting § 603.900...

Reducing school bus/light-vehicle conflicts through connected vehicle communications : final report.

DOT National Transportation Integrated Search

2016-09-15

This project aimed to develop and test a concept for improving the safety of school bus transportation using connected vehicle technology. The project consisted of three key steps that led to a final road study: 1) conducting focus groups with light ...

Advanced Gas Turbine (AGT) technology development project

NASA Technical Reports Server (NTRS)

1987-01-01

This report is the final in a series of Technical Summary Reports for the Advanced Gas Turbine (AGT) Technology Development Project, authorizrd under NASA Contract DEN3-167 and sponsored by the DOE. The project was administered by NASA-Lewis Research Center of Cleveland, Ohio. Plans and progress are summarized for the period October 1979 through June 1987. This program aims to provide the US automotive industry the high risk, long range technology necessary to produce gas turbine engines for automobiles that will reduce fuel consumption and reduce environmental impact. The intent is that this technology will reach the marketplace by the 1990s. The Garrett/Ford automotive AGT was designated AGT101. The AGT101 is a 74.5 kW (100 shp) engine, capable of speeds to 100,000 rpm, and operates at turbine inlet temperatures to 1370 C (2500 F) with a specific fuel consumption level of 0.18 kg/kW-hr (0.3 lbs/hp-hr) over most of the operating range. This final report summarizes the powertrain design, power section development and component/ceramic technology development.

UNIVERSITY OF ARIZONA CROSS-BORDER WATER TECHNOLOGY COLLABORATION

EPA Science Inventory

The outcome of Phase I of the University of Arizona Cross-border Water Technology Collaboration project was the development and testing of solar distillation designs and selection of the final design for implementation that could be built in a developing country...

Improvement of Base and Soil Construction Quality by Using Intelligent Compaction Technology : Final Report.

DOT National Transportation Integrated Search

2017-08-01

Intelligent Compaction (IC) technique is a fast-developing technology for base and soil compaction quality control. Proof-rolling subgrades and bases using IC rollers upon completion of compaction can identify the less stiff spots and significantly i...

International Space Station (ISS)

NASA Image and Video Library

1994-07-20

An artist's conception of what the final configuration of the International Space Station (ISS) will look like when it is fully built and deployed. The ISS is a multidisciplinary laboratory, technology test bed, and observatory that will provide an unprecedented undertaking in scientific, technological, and international experimentation.

SmartPark Technology Demonstration Project, Phase II: Final Report

DOT National Transportation Integrated Search

2018-05-01

The purpose of FMCSA's SmartPark project was to determine the feasibility of a technology for providing truck parking space availability information in real time to truckers on the road. SmartPark consisted of two phases. Phase I was a field operatio...

Advanced technology gas-fired commercial clothes dryer. Final report, April 1985-December 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Topping, R.F.

1991-04-01

The objective of this effort was to demonstrate the technical feasibility of an advanced technology commercial clothes dryer (ATD) which could provide improved fuel efficiency and reduced drying time without burning or otherwise damaging the clothes load.

Information Processing Technology. Final Report.

ERIC Educational Resources Information Center

Choate, Larry; And Others

A tech prep/associate degree program in information technology was developed to prepare workers for entry into and advancement in occupations entailing applications of scientific principles and higher mathematics in situations involving various office machines. According to the articulation agreement reached, students from five country regional…

Three-Dimensional User Interfaces for Immersive Virtual Reality

NASA Technical Reports Server (NTRS)

vanDam, Andries

1997-01-01

The focus of this grant was to experiment with novel user interfaces for immersive Virtual Reality (VR) systems, and thus to advance the state of the art of user interface technology for this domain. Our primary test application was a scientific visualization application for viewing Computational Fluid Dynamics (CFD) datasets. This technology has been transferred to NASA via periodic status reports and papers relating to this grant that have been published in conference proceedings. This final report summarizes the research completed over the past year, and extends last year's final report of the first three years of the grant.

SUPERFUND TREATABILITY CLEARINGHOUSE: FINAL ...

EPA Pesticide Factsheets

During the period of July 8 - July 12, 1985, the Shirco Infrared Systems Portable Pilot Test Unit was in operation at the Times Beach Dioxin Research Facility to demonstrate the capability of Shirco's infrared technology to decontaminate silty soil laden with 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) at a concentration range of 156 to 306 ppb. Emissions sampling and final analysis was performed by Environmental Research & Technology, Inc. (ERT), while laboratory analysis of the emissions and soil samples was performed by Roy F. Weston Inc. Shirco Infrared Systems prepared the testing procedure protocol and operated the furnace system. publish information

Technology Interdependency Roadmaps for Space Operations

NASA Technical Reports Server (NTRS)

Krishen, Kumar

1995-01-01

The requirements for Space Technology are outlined in terms of NASA Strategic Plan. The national emphasis on economic revitalization is described along with the environmental changes needed for the new direction. Space Technology Interdependency (STI) is elaborated in terms of its impact on national priority on science, education, and economy. Some suggested approaches to strengthening STI are outlined. Finally, examples of Technology Roadmaps for Space Operations area are included to illustrate the value of STI for national cohesiveness and economic revitalization.

Enhancing emergency care in low-income countries using mobile technology-based training tools

PubMed Central

Edgcombe, Hilary; Paton, Chris; English, Mike

2016-01-01

In this paper, we discuss the role of mobile technology in developing training tools for health workers, with particular reference to low-income countries (LICs). The global and technological context is outlined, followed by a summary of approaches to using and evaluating mobile technology for learning in healthcare. Finally, recommendations are made for those developing and using such tools, based on current literature and the authors' involvement in the field. PMID:27658948

Development of coverage with evidence development for medical technologies in Switzerland from 1996 to 2012.

PubMed

Brügger, Urs; Ruckstuhl, Andreas; Horisberger, Bruno; Gratwohl, Alois

2014-07-01

The aim of this study was to assess incidence, time frame, and outcome of "Coverage with Evidence Development" (CED) decisions in the Swiss Basic Health Insurance scheme. Analysis of all controversial medical technologies submitted to review by the Swiss Federal Office of Public Health (FOPH) from 1996 to 2012 with focus on decisions with constraints. Description of types of technology, type of initial decision, duration of evaluation period, final decision, and search for potential factors associated with changes over time. Forty-five (37.5 percent) of 120 controversial health technologies were classified as "yes, in evaluation, reimbursed" for a certain period of time and thirty-five (29.2 percent) as "no, in evaluation, not reimbursed" by the Federal Department of Home Affairs from 1996 to 2012. The rate of CED decisions ranged between zero and nine per year and was influenced by type of technology and calendar year. Forty-four of forty-five decisions were subject to further restrictions, to a "center or a specialist" (76 percent), "indications" (49 percent), "registry" (31 percent), or "other" (49 percent). The time to a final decision ranged from 1.5 to 11 years (median, 6 years). No factors associated with initial decision and final outcome could be identified. CED as a reality in Switzerland might have enabled patients to obtain access to promising technologies early in their life cycle. CED might have acted as a trigger to a successful implementation of a comprehensive national registry. The lack of qualitative data stresses the urgent need for evaluation of the HTA decisions and their impact on patient outcome and costs.

Technical analysis of US Army Weapons Systems and related advanced technologies of military interest. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1991-06-14

This report summarizes the activities and accomplishments of an US Army technology security project designed to identify and develop effective policy guidelines for militarily critical technologies in specific Army systems and in broad generic technology areas of military interest, Individual systems analyses are documented in separate Weapons Systems Technical Assessments (WSTAs) and the general generic technology areas are evaluated in the Advanced Technology Assessment Reports (ATARs), However, specific details of these assessments are not addressed here, only recommendations regarding aspects of the defined approach, methodology, and format are provided and discussed.

Petrographic microscope investigation of mortar and ceramic technologies for the conservation of the built heritage

NASA Astrophysics Data System (ADS)

Pavia, S.; Caro, S.

2007-07-01

Polarised-light (or petrographic) microscopy has been widely applied to heritage materials to assess composition and diagnose damage. However, instead, this paper focuses on the petrographic investigation of brick and mortar technologies for the production of quality repair materials compatible with their adjacent fabrics. Furthermore, the paper relates production technologies to the physical properties of the materials fabricated, and thus their final quality and durability. According to Cesare Brandi´s theory of compatibility (the 20th century architect on whose work modern conservation theory and practice are largely based) existing historic materials should be replaced with their equivalent. This paper demonstrates that polarised-light microscopy provides data on the origin and nature of raw materials, and processing parameters such as blending, mixing, firing, calcination and slaking, and how these relate to the quality of the final product. In addition, this paper highlights the importance of production technologies as these directly impact the physical properties of the materials fabricated and thus determine their final quality and durability. In this context, the paper investigates mortar calcination and slaking, two important operations in the manufacture of building limes that govern the reactivity, shrinkage and water retention of a lime binder which will impact mortar's properties such as workability, plasticity and carbonation speed, and these in turn will determine the ease of execution, durability and strength of a lime mortar. Petrographic analysis also provides evidence of ceramic technology including identification of local or foreign production and processing parameters such as sieving, blending, mixing and firing. A petrographic study of the ceramic matrix coupled to the diagnosis of mineral phases formed during firing allows to quantify sintering and vitrification and thus determine firing temperatures. Finally, certain features of the raw clay such as the grading and the amount and nature of the non-plastic material inform, not only on the raw material's origin, but also impact the physical properties of the ceramic ware.

Cost/benefit analysis of advanced materials technologies for future aircraft turbine engines

NASA Technical Reports Server (NTRS)

Stephens, G. E.

1980-01-01

The materials technologies studied included thermal barrier coatings for turbine airfoils, turbine disks, cases, turbine vanes and engine and nacelle composite materials. The cost/benefit of each technology was determined in terms of Relative Value defined as change in return on investment times probability of success divided by development cost. A recommended final ranking of technologies was based primarily on consideration of Relative Values with secondary consideration given to changes in other economic parameters. Technologies showing the most promising cost/benefits were thermal barrier coated temperature nacelle/engine system composites.

1983 LTA technology assessment

NASA Technical Reports Server (NTRS)

Ashford, R. L.; Browning, R. G. E.; Levitt, B. B.; Mayer, N. J.; Woodward, D. E.

1983-01-01

Several aspects of LTA (lighter-than-air) technology development are reviewed. Technological developments of classical airships through 1974 are examined. A brief historical and technological summary of five specialized LTA equipment concepts is presented: metal-clad airships, free balloons, semibuoyant vehicles, high-altitude platforms, and tethered aerostats. Current LTA technology developments are reviewed with particular emphasis on VTOL airships capable of heavy lift and on long endurance types for coastal maritime patrol. Finally, the future prospects of LTA system development are considered with attention given to manned conventional and hybrid vehicles, tethered vehicles, and RPVs.

Risk management. National Aeronautics and Space Administration (NASA). Interim rule adopted as final with changes.

PubMed

2000-11-22

This is a final rule amending the NASA FAR Supplement (NFS) to emphasize considerations of risk management, including safety, security (including information technology security), health, export control, and damage to the environment, within the acquisition process. This final rule addresses risk management within the context of acquisition planning, selecting sources, choosing contract type, structuring award fee incentives, administering contracts, and conducting contractor surveillance.

Data breaches. Final rule.

PubMed

2008-04-11

This document adopts, without change, the interim final rule that was published in the Federal Register on June 22, 2007, addressing data breaches of sensitive personal information that is processed or maintained by the Department of Veterans Affairs (VA). This final rule implements certain provisions of the Veterans Benefits, Health Care, and Information Technology Act of 2006. The regulations prescribe the mechanisms for taking action in response to a data breach of sensitive personal information.

Sensing technology for damage assessment of sign supports and cantilever poles : final report, August 31, 2010.

DOT National Transportation Integrated Search

2010-08-31

This report presents the results of research activities conducted under Contract No. 519691-PIT 008 on Sensing Technology for : Damage Assessment of Sign Supports and Cantilever Poles between the University of Pittsburgh and the Pennsylvania De...

Overcoming barriers to ITS : lessons from other technologies : final task E report

DOT National Transportation Integrated Search

1995-12-01

The Task E report involves an analysis of franchises and license agreements for the provision of public services, which is the fourth in a series in the study. Overcoming Barriers to ITS - Lessons from Other Technologies. This report follows alternat...

Final Barrier: Small System Compliance

EPA Science Inventory

This presentation will discuss the use of point-of-use (POU) technology for small drinking water systems. Information will be provided on the USEPA regulations that allow the use of POU for compliance and the technologies that are listed as SSCT for radium and arsenic. Listing o...

Registration of Large Motion Blurred CMOS Images

DTIC Science & Technology

2017-08-28

raju@ee.iitm.ac.in - Institution : Indian Institute of Technology (IIT) Madras, India - Mailing Address : Room ESB 307c, Dept. of Electrical ...AFRL-AFOSR-JP-TR-2017-0066 Registration of Large Motion Blurred CMOS Images Ambasamudram Rajagopalan INDIAN INSTITUTE OF TECHNOLOGY MADRAS Final...NUMBER 5f.  WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) INDIAN INSTITUTE OF TECHNOLOGY MADRAS SARDAR PATEL ROAD Chennai, 600036

Logistics Supply of the Distributed Air Wing

DTIC Science & Technology

2014-09-01

distribution is unlimited LOGISTICS SUPPLY OF THE DISTRIBUTED AIR WING Chee Siong Ong Civilian, Defence Science and Technology Agency B.Eng., Nanyang... Technological University, 2004 Submitted in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE IN MODELING, VIRTUAL...Department, for his advice on the Marine Aviation Logistics Supply Program. Finally, I am very grateful to my company, Defence Science and Technology

Arsenic Removal from Drinking Water by Point of Entry/Point of Use Adsorptive Media U.S. EPA Demonstration Project at Oregon Institute of Technology at Klamath Falls, OR - Final Performance Evaluation Report

EPA Science Inventory

This report documents the activities performed during and the results obtained from the arsenic removal treatment technology demonstration project at Oregon Institute of Technology (OIT) at Klamath Falls, OR. The objectives of the project were to evaluate: (1) the effectiveness...

Research of negotiation in network trade system based on multi-agent

NASA Astrophysics Data System (ADS)

Cai, Jun; Wang, Guozheng; Wu, Haiyan

2009-07-01

A construction and implementation technology of network trade based on multi-agent is described in this paper. First, we researched the technology of multi-agent, then we discussed the consumer's behaviors and the negotiation between purchaser and bargainer which emerges in the traditional business mode and analysed the key technology to implement the network trade system. Finally, we implement the system.

Research progress of free space coherent optical communication

NASA Astrophysics Data System (ADS)

Tan, Zhenkun; Ke, Xizheng

2018-02-01

This paper mainly introduces the research progress of free space coherent optical communication in Xi'an University of Technology. In recent years, the research on the outer modulation technology of the laser, free-space-to-fiber coupling technique, the design of transmitting and receiving optical antenna, adaptive optical technology with or without wave-front sensor, automatic polarization control technology, frequency stabilization technology, heterodyne detection technology and high speed signal processing technology. Based on the above related research, the digital signal modulation, transmission, detection and data recovery are realized by the heterodyne detection technology in the free space optical communication system, and finally the function of smooth viewing high-definition video is realized.

77 FR 49722 - Cranes and Derricks in Construction: Demolition and Underground Construction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-17

... cranes rule, OSHA prepared a final economic analysis (FEA) as required by the Occupational Safety and... construction work involving demolition. The FEA for the final cranes standard, which included all cranes, crane... were technologically and economically feasible. Because the FEA drew these conclusions from...

Final report from VFL Technologies for the pilot-scale thermal treatment of lower East Fork Poplar Creek floodplain soils. LEFPC appendices, Volume 4, Appendix V-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-09-01

This is the the final verification run data package for pilot scale thermal treatment of lower East Fork Poplar Creek floodplain soils. Included are data on volatiles, semivolatiles, and TCLP volatiles.

26 CFR 1.142(a)(6)-1 - Exempt facility bonds: solid waste disposal facilities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... biological, engineering, industrial, or technological method. (1) Final disposal process. The term final... solid material derived from any agricultural, commercial, consumer, governmental, or industrial... industrial operation or activity, or a component of any such product or activity, and that has been used...

26 CFR 1.142(a)(6)-1 - Exempt facility bonds: solid waste disposal facilities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... biological, engineering, industrial, or technological method. (1) Final disposal process. The term final... solid material derived from any agricultural, commercial, consumer, governmental, or industrial... industrial operation or activity, or a component of any such product or activity, and that has been used...

NASA aeronautics R&T - A resource for aircraft design

NASA Technical Reports Server (NTRS)

Olstad, W. B.

1981-01-01

This paper discusses the NASA aeronautics research and technology program from the viewpoint of the aircraft designer. The program spans the range from fundamental research to the joint validation with industry of technology for application into product development. Examples of recent developments in structures, materials, aerodynamics, controls, propulsion systems, and safety technology are presented as new additions to the designer's handbook. Finally, the major thrusts of NASA's current and planned programs which are keyed to revolutionary advances in materials science, electronics, and computer technology are addressed.

A Multi-scale, Multi-Model, Machine-Learning Solar Forecasting Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamann, Hendrik F.

The goal of the project was the development and demonstration of a significantly improved solar forecasting technology (short: Watt-sun), which leverages new big data processing technologies and machine-learnt blending between different models and forecast systems. The technology aimed demonstrating major advances in accuracy as measured by existing and new metrics which themselves were developed as part of this project. Finally, the team worked with Independent System Operators (ISOs) and utilities to integrate the forecasts into their operations.

SNAP-8 electrical generating system development program

NASA Technical Reports Server (NTRS)

1971-01-01

The SNAP-8 program has developed the technology base for one class of multikilowatt dynamic space power systems. Electrical power is generated by a turbine-alternator in a mercury Rankine-cycle loop to which heat is transferred and removed by means of sodium-potassium eutectic alloy subsystems. Final system overall criteria include a five-year operating life, restartability, man rating, and deliverable power in the 90 kWe range. The basic technology has been demonstrated by more than 400,000 hours of major component endurance testing and numerous startup and shutdown cycles. A test system, comprised of developed components, delivered up to 35 kWe for a period exceeding 12,000 hours. The SNAP-8 system baseline is considered to have achieved a level of technology suitable for final application development for long-term multikilowatt space missions.

[A micro-silicon multi-slit spectrophotometer based on MEMS technology].

PubMed

Hao, Peng; Wu, Yi-Hui; Zhang, Ping; Liu, Yong-Shun; Zhang, Ke; Li, Hai-Wen

2009-06-01

A new mini-spectrophotometer was developed by adopting micro-silicon slit and pixel segmentation technology, and this spectrophotometer used photoelectron diode array as the detector by the back-dividing-light way. At first, the effect of the spectral bandwidth on the tested absorbance linear correlation was analyzed. A theory for the design of spectrophotometer's slit was brought forward after discussing the relationships between spectrophotometer spectrum band width and pre-and post-slits width. Then, the integrative micro-silicon-slit, which features small volume, high precision, and thin thickness, was manufactured based on the MEMS technology. Finally, a test was carried on linear absorbance solution by this spectrophotometer. The final result showed that the correlation coefficients were larger than 0.999, which means that the new mini-spectrophotometer with micro-silicon slit pixel segmentation has an obvious linear correlation.

Spectrographs for astrophotonics.

PubMed

Blind, N; Le Coarer, E; Kern, P; Gousset, S

2017-10-30

The next generation of extremely large telescopes (ELT), with diameters up to 39 meters, is planned to begin operation in the next decade and promises new challenges in the development of instruments since the instrument size increases in proportion to the telescope diameter D, and the cost as D 2 or faster. The growing field of astrophotonics (the use of photonic technologies in astronomy) could solve this problem by allowing mass production of fully integrated and robust instruments combining various optical functions, with the potential to reduce the size, complexity and cost of instruments. Astrophotonics allows for a broad range of new optical functions, with applications ranging from sky background filtering, high spatial and spectral resolution imaging and spectroscopy. In this paper, we want to provide astronomers with valuable keys to understand how photonics solutions can be implemented (or not) according to the foreseen applications. The paper introduces first key concepts linked to the characteristics of photonics technologies, placed in the framework of astronomy and spectroscopy. We then describe a series of merit criteria that help us determine the potential of a given micro-spectrograph technology for astronomy applications, and then take an inventory of the recent developments in integrated micro-spectrographs with potential for astronomy. We finally compare their performance, to finally draw a map of typical science requirements and pin the identified integrated technologies on it. We finally emphasize the necessary developments that must support micro-spectrograph in the coming years.

Educational Benefits of Multimedia Skills Training

ERIC Educational Resources Information Center

Wang, Tsung juang

2010-01-01

The use of multimedia technologies in education has enabled teachers to simulate final outcomes and assist students in applying knowledge learned from textbooks, thereby compensating for the deficiency of traditional teaching methods. It is important to examine how effective these technologies are in practical use. This study developed online…

Technology Education Demonstration Project. Final Report.

ERIC Educational Resources Information Center

Appalachian Technology Education Consortium, Morgantown, WV.

Year 1 of the Appalachian Technology Education Consortium Demonstration Project began with formation of an executive committee to serve as the managerial arm and establishment of a board of directors to determine policy direction. Other activities included planning for external evaluation, recruiting of demonstration and observer schools, and…

ECMT31 New Mexico Manufacturing Environmental Survey. Final Report.

ERIC Educational Resources Information Center

Sandia National Labs., Albuquerque, NM.

The Environmentally Conscious Manufacturing Technology Transfer and Training Initiative (ECMT3I) is a cooperative effort among education and research institutions in New Mexico to analyze problems in transferring environmental technologies from Department of Energy laboratories to small and medium enterprises (SME's). To identify and analyze…

Language Integrated Technology Project Final Evaluation Report.

ERIC Educational Resources Information Center

Stiegemeier, Lois

The goal of the Language Integrated Technology Grant Project (LIT) consortium was to help provide critical components of successful reading programs through a combination of proven computer/print programs and teacher training. Through leadership provided by the Educational Service District 113 (Olympia, Washington), the LIT consortium of schools…

Potential Technology Transfer to the DoD Unmanned Ground Vehicle Program.

DTIC Science & Technology

1996-10-01

Germany. This process combines x-ray lithography, galvanic casting, and micromolding technology and can be used to produce a variety of sensors and...whether circulation is being obstructed by atherosclerosis . Finally, work is being done at the University of Minnesota on a microrobotic device

Advancing the use of streaming media and digital media technologies at the Connecticut Department of Transportation.

DOT National Transportation Integrated Search

2014-03-27

This final research report culminates a decade-long initiative to demonstrate and implement streaming media technologies at CONNDOT. This effort began in 2001 during an earlier related-study (SPR-2231) that concluded in 2006. This study (SPR-2254) re...

Installation of active noise control and active vibration control on a GP40-2 locomotive : final report.

DOT National Transportation Integrated Search

2016-06-01

This project evaluated the performance of active noise control (ANC) and active vibration control (AVC) technologies using a GP40-2 locomotive located at the Transportation Technology Center (TTC) near Pueblo, CO, to determine the applicability of AN...

Vehicle-to-Vehicle crash avoidance technology : public acceptance final report.

DOT National Transportation Integrated Search

2015-12-01

The Vehicle-to-Vehicle (V2V) Crash Avoidance Public Acceptance report summarizes data from a survey of the current level of awareness and acceptance of V2V technology. The survey was guided by findings from prior studies and 12 focus groups. A total ...

Cost Benefit Studies. Final Report.

ERIC Educational Resources Information Center

Weiner, Arthur; Marson, Arthur A.

This document applies Dr. Mehar Aurora's method for conducting cost benefit studies to the Food Manufacturing Technology-Dairy and the Food Manufacturing Technology-Canning and Freezing programs offered by the Moraine Park Technical Institute. Costs to individual students enrolled in the programs include tuition, fees, housing, travel, books,…

Places and networks : the changing landscape of transportation and technology, final summary report of the STAR-TEA 21 project.

DOT National Transportation Integrated Search

2008-12-01

Over the past six years, researchers from the University of Minnesota have studied the many ways in which transportation and technology intersect. Their work has explored these intersections from many perspectives, from ways intelligent transportatio...

75 FR 20812 - Silicon Metal from Brazil: Amended Final Results of Administrative Review Pursuant to Court Decision

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-21

... regarding the 94/95 period of review. See American Silicon Technologies v. United States, 28 C.I.T. 698.../95 period of review. See American Silicon Technologies v. United States, 27 C.I.T. 1677; 2003 Ct...

National Renewable Energy Laboratory (NREL) Topic 2 Final Report: End-to-End Communication and Control System to Support Clean Energy Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hudgins, Andrew P.; Carrillo, Ismael M.; Jin, Xin

This document is the final report of a two-year development, test, and demonstration project, 'Cohesive Application of Standards- Based Connected Devices to Enable Clean Energy Technologies.' The project was part of the National Renewable Energy Laboratory's (NREL's) Integrated Network Testbed for Energy Grid Research and Technology (INTEGRATE) initiative hosted at Energy Systems Integration Facility (ESIF). This project demonstrated techniques to control distribution grid events using the coordination of traditional distribution grid devices and high-penetration renewable resources and demand response. Using standard communication protocols and semantic standards, the project examined the use cases of high/low distribution voltage, requests for volt-ampere-reactive (VAR)more » power support, and transactive energy strategies using Volttron. Open source software, written by EPRI to control distributed energy resources (DER) and demand response (DR), was used by an advanced distribution management system (ADMS) to abstract the resources reporting to a collection of capabilities rather than needing to know specific resource types. This architecture allows for scaling both horizontally and vertically. Several new technologies were developed and tested. Messages from the ADMS based on the common information model (CIM) were developed to control the DER and DR management systems. The OpenADR standard was used to help manage grid events by turning loads off and on. Volttron technology was used to simulate a homeowner choosing the price at which to enter the demand response market. Finally, the ADMS used newly developed algorithms to coordinate these resources with a capacitor bank and voltage regulator to respond to grid events.« less

Design Recovery Technology for Real-Time Systems.

DTIC Science & Technology

1995-10-01

RL-TR-95-208 Final Technical Report October 1995 DESIGN RECOVERY TECHNOLOGY FOR REAL TIME SYSTEMS The MITRE Corporation Lester J. Holtzblatt...92 - Jan 95 4. TTTLE AND SUBTITLE DESIGN RECOVERY TECHNOLOGY FOR REAL - TIME SYSTEMS 6. AUTHOR(S) Lester J. Holtzblatt, Richard Piazza, and Susan...behavior of real - time systems in general, our initial efforts have centered on recovering this information from one system in particular, the Modular

Review of fluid and control technology of hydraulic wind turbines

NASA Astrophysics Data System (ADS)

Cai, Maolin; Wang, Yixuan; Jiao, Zongxia; Shi, Yan

2017-09-01

This study examines the development of the fluid and control technology of hydraulic wind turbines. The current state of hydraulic wind turbines as a new technology is described, and its basic fluid model and typical control method are expounded by comparing various study results. Finally, the advantages of hydraulic wind turbines are enumerated. Hydraulic wind turbines are expected to become the main development direction of wind turbines.

Final Technical Report: Hawaii Energy and Environmental Technologies Initiative 2009 (HEET)

DTIC Science & Technology

2016-05-25

environment. A second objective under this subtask was to install, test and evaluate small wind turbine technologies to determine the relative... wind turbines adjacent to, and connected with the test platforms located at the Crissy Field Center in the Presidio of San Francisco, a proven wind ...resource for collection of comparative wind energy data. Vertical axis technology, turbines manufactured by Venco Power, Windspire Energy and

Solidification Technologies for Radioactive and Chemical Liquid Waste Treatment - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castiglioni, Andrew J.; Gelis, Artem V.

This project, organized under DOE/NNSA's Global Initiatives for Proliferation Prevention program, joined Russian and DOE scientists in developing more effective solidification and storage technologies for liquid radioactive waste. Several patent applications were filed by the Russian scientists (Russia only) and in 2012, the technology developed was approved by Russia's Federal State Unitary Enterprise RADON for application throughout Russia in cleaning up and disposing of radioactive waste.

Review of Military Mountain Medicine Technology and Research Barriers

DTIC Science & Technology

2011-09-01

NORTH ATLANTIC TREATY ORGANISATION RESEARCH AND TECHNOLOGY ORGANISATION AC/323(HFM-146)TP/387 www.rto.nato.int RTO TECHNICAL REPORT TR...montagne et les freins à la recherche) Final Report of Task Group HFM-146. Published September 2011 Distribution and Availability...323(HFM-146)TP/387 www.rto.nato.int RTO TECHNICAL REPORT TR-HFM-146 Review of Military Mountain Medicine Technology and Research Barriers (Point

ARN Program, PDIT Final Technical Report - Deliver Orders 3, 12, 13

DTIC Science & Technology

2005-07-05

Product Data Integration Technologies , Inc. dba Modulant 444 W Ocean Blvd, Suite 620 Long Beach, CA 90802 9. SPONSORING / MONITORING AGENCY NAME(S...HQ, Fort Belvoir, VA Prepared by: Product Data Integration Technologies , DBA Modulant 444 West Ocean Blvd, Suite 620 Long Beach, California...we originally planned. We had planned to simply stay generally aware of the DOD’s initiates and technology advances, thinking that the application

The Cognition and Neuroergonomics (CaN) Collaborative Technology Alliance (CTA): Scientific Vision, Approach, and Translational Paths

DTIC Science & Technology

2012-09-01

The Cognition and Neuroergonomics (CaN) Collaborative Technology Alliance (CTA): Scientific Vision, Approach, and Translational Paths by...The Cognition and Neuroergonomics (CaN) Collaborative Technology Alliance (CTA): Scientific Vision, Approach, and Translational Paths Kelvin S. Oie...REPORT DATE (DD-MM-YYYY) September 2012 2. REPORT TYPE Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE The Cognition and Neuroergonomics

Par-baked Bread Technology: Formulation and Process Studies to Improve Quality.

PubMed

Almeida, Eveline Lopes; Steel, Caroline Joy; Chang, Yoon Kil

2016-01-01

Extending the shelf-life of bakery products has been an important requirement resulting from the mechanization of this industry and the need to increase the distance for the distribution of final products, caused by the increase in production and consumer demand. Technologies based on the interruption of the breadmaking process represent an alternative to overcome product staling and microbiological deterioration. The production of par-baked breads is one of these technologies. It consists of baking the bread in two stages, and due to the possibility of retarding the second stage, it can be said that the bread can always be offered fresh to the consumer. The technology inserts logistics as part of the production process and creates the "hot point" concept, these being the locations where the bread is finalized, such as in the consumers' homes or sales locations. In this work, a review of the papers published on this subject was carried out, and aspects related to both the formulation and the process were considered. This technology still faces a few challenges, such as solving bread quality problems that appear due to process modifications, and these will also be considered. The market for these breads has grown rapidly and the bakery industry searches innovations related to par-baked bread technology.

Present situation and trend of precision guidance technology and its intelligence

NASA Astrophysics Data System (ADS)

Shang, Zhengguo; Liu, Tiandong

2017-11-01

This paper first introduces the basic concepts of precision guidance technology and artificial intelligence technology. Then gives a brief introduction of intelligent precision guidance technology, and with the help of development of intelligent weapon based on deep learning project in foreign: LRASM missile project, TRACE project, and BLADE project, this paper gives an overview of the current foreign precision guidance technology. Finally, the future development trend of intelligent precision guidance technology is summarized, mainly concentrated in the multi objectives, intelligent classification, weak target detection and recognition, intelligent between complex environment intelligent jamming and multi-source, multi missile cooperative fighting and other aspects.

Smart Gun Technology project. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weiss, D.R.

The goal of the Smart Gun Technology project is to eliminate the capability of an unauthorized user form firing a law officer`s firearm by implementing user-recognizing-and-authorizing (or {open_quotes}smart{close_quotes}) surety technologies. This project was funded by the National Institute of Justice. This report lists the findings and results of the project`s three primary objectives. First, to find and document the requirements for a smart firearm technology that law enforcement officers will value. Second, to investigate, evaluate, and prioritize technologies that meet the requirements for a law enforcement officer`s smart firearm. Third, to demonstrate and document the most promising technology`s usefulness inmore » models of a smart firearm.« less

Design and realization of intelligent tourism service system based on voice interaction

NASA Astrophysics Data System (ADS)

Hu, Lei-di; Long, Yi; Qian, Cheng-yang; Zhang, Ling; Lv, Guo-nian

2008-10-01

Voice technology is one of the important contents to improve the intelligence and humanization of tourism service system. Combining voice technology, the paper concentrates on application needs and the composition of system to present an overall intelligent tourism service system's framework consisting of presentation layer, Web services layer, and tourism application service layer. On the basis, the paper further elaborated the implementation of the system and its key technologies, including intelligent voice interactive technology, seamless integration technology of multiple data sources, location-perception-based guides' services technology, and tourism safety control technology. Finally, according to the situation of Nanjing tourism, a prototype of Tourism Services System is realized.

Emerging Communication Technologies (ECT) Phase 3 Final Report

NASA Technical Reports Server (NTRS)

Bastin, Gary L.; Harris, William G.; Bates, Lakesha D.; Nelson, Richard A.

2004-01-01

The Emerging Communication Technology (ECT) project investigated three First Mile communication technologies in support of NASA s Second Generation Reusable Launch Vehicle (2nd Gen RLV), Orbital Space Plane, Advanced Range Technology Working Group (ARTWG) and the Advanced Spaceport Technology Working Group (ASTWG). These First Mile technologies have the purpose of interconnecting mobile users with existing Range Communication infrastructures. ECT was a continuation of the Range Information System Management (RISM) task started in 2002. RISM identified the three advance communication technologies investigated under ECT. These were Wireless Ethernet (Wi-Fi), Free Space Optics (FSO), and Ultra Wideband (UWB). Due to the report s size, it has been broken into three volumes: 1) Main Report 2) Appendices 3) UWB.

76 FR 9054 - Notice of Availability of Final Environmental Impact Statement for the AREVA Enrichment Services...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-16

... as supplemental information on a proposed electrical transmission line required to power the proposed... proposed uranium enrichment facility. Specifically, AES proposes to use gas centrifuge technology to enrich...; and (3) alternative technologies for uranium enrichment. These alternatives were eliminated from...

FIELD TEST MEASUREMENTS AT FIVE MUNICIPAL SOLID WASTE LANDFILLS WITH LANDFILL GAS CONTROL TECHNOLOGY--FINAL REPORT

EPA Science Inventory

Research was conducted to evaluate landfill gas emissions at five municipal solid waste landfills which have modern control technology for landfill gas emissions. Comprehensive testing was conducted on the raw landfill gas and the combustion outlet exhaust. The project had two ...

FOOD PROCESSING TECHNOLOGY, A SUGGESTED 2-YEAR POST HIGH SCHOOL CURRICULUM.

ERIC Educational Resources Information Center

KNOEBEL, ROBERT M.; AND OTHERS

ADMINISTRATORS, ADVISORY COMMITTEES, SUPERVISORS, AND TEACHERS MAY USE THIS GUIDE IN PLANNING AND DEVELOPING NEW PROGRAMS OR EVALUATING EXISTING PROGRAMS IN POST-HIGH SCHOOL FOOD PROCESSING TECHNOLOGY. BASIC MATERIALS WERE PREPARED BY THE STATE UNIVERSITY OF NEW YORK AGRICULTURAL AND TECHNICAL COLLEGE AT MORRISVILLE AND FINAL PREPARATION WAS…

77 FR 48733 - Transitional Program for Covered Business Method Patents-Definitions of Covered Business Method...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-14

... Office 37 CFR Part 42 Transitional Program for Covered Business Method Patents--Definitions of Covered Business Method Patent and Technological Invention; Final Rule #0;#0;Federal Register / Vol. 77 , No. 157... Business Method Patents-- Definitions of Covered Business Method Patent and Technological Invention AGENCY...

ITS strategic deployment plan : Nashville area intelligent transportation systems early deployment study. Technical memorandum no. 8, Final report

DOT National Transportation Integrated Search

1997-03-01

The goal of this study was to develop a Strategic Plan for deployment of ITS technologies within the Nashville Metro Area and to create a long-term coalition of ITS stakeholders, with the objective of expanding the implementation of ITS technologies ...

An Analysis of Student Hypermedia Navigation and Learning

ERIC Educational Resources Information Center

Epp, Erik Minh

2010-01-01

As society's interactions with web technology mature from novelty to familiarity and finally into transparence for users, it becomes important to reexamine what modern students are taking from their experiences with educational technology. Students in a physical chemistry laboratory course interacted with a hypermedia learning environment as part…

Evaluation of warm mix technologies for use in asphalt rubber - asphaltic concrete friction courses (AR\\0x2010ACFC) : final report.

DOT National Transportation Integrated Search

2016-07-01

The objective of this research project was to determine whether warm mix asphalt (WMA) technologies can be : used by the Arizona Department of Transportation (ADOT) for the production of an asphalt rubberasphaltic : concrete friction course (AR...

Information Systems and Networks for Technology Transfer. Final Report.

ERIC Educational Resources Information Center

Page, John; Szentivanyi, Tibor

Results of a survey of the information resources available in industrialized countries which might be used in a United Nations technology transfer program for developing countries are presented. Information systems and networks, organized information collections of a scientific and technical character, and the machinery used to disseminate this…

Development of Generalizable Educational Programs in Laser/Electro-Optics Technology: Final Report.

ERIC Educational Resources Information Center

Hull, Daniel M.

The purpose of the Laser/Electro-Optics Technology (LEOT) Project was to establish a pilot educational program, develop a flexible curriculum, prepare and test instructional materials, transport the curriculum and instructional materials into other educational institutions by establishing relevant LEOT programs wherever they are needed, and to…

Collaborative Technologies: Three Ways Web Conferencing is Transforming PD

ERIC Educational Resources Information Center

Raths, David

2013-01-01

The first five articles of this series on technologies that enable collaboration, highlighted ways to foster shared learning experiences among students. For this, the final installment, focus is shifted to teachers. States, districts, and groups of teachers are enhancing their collaboration opportunities through synchronous online meetings and…

New Technology and the Public Library. Final Report and Executive Summary.

ERIC Educational Resources Information Center

Griffiths, Jose-Marie; King, Donald W.

This report presents current and potential library applications of new technologies, issues surrounding their introduction into public libraries, and activities suggested for use during the introduction procedure. A brief appraisal of the public library's role in the information transfer process precedes a review of library automation in…

76 FR 8721 - Notice of Submission for OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

...'' grants that are awarded funds for their entire multi-year project up-front in a single grant award to... the ED 524B to submit their final performance reports to demonstrate project success, impact and..., mechanical, or other technological collection techniques or other forms of information technology. Dated...

76 FR 12945 - Notice of Submission for OMB Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-09

... awarded funds for their entire multi-year project up- front in a single grant award to submit the RPPR on... their final performance reports to demonstrate project success, impact and outcomes. In both the annual..., mechanical, or other technological collection techniques or other forms of information technology. [[Page...

A Fifteen-Year Forecast of Information-Processing Technology. Final Report.

ERIC Educational Resources Information Center

Bernstein, George B.

This study developed a variation of the DELPHI approach, a polling technique for systematically soliciting opinions from experts, to produce a technological forecast of developments in the information-processing industry. SEER (System for Event Evaluation and Review) combines the more desirable elements of existing techniques: (1) intuitive…

Use of Interdisciplinary Education to Foster Familiarization among Health Professionals.

ERIC Educational Resources Information Center

Laatsch, Linda J.; And Others

1986-01-01

Describes a pilot interdisciplinary experience between the dental hygiene and medical technology programs at Marquette University. It was designed, in part, to familiarize dental hygiene students with the medical technology profession. Comments solicited from students on the final evaluation form indicated that this pilot project was highly…

Validation of the Proficiency Examination for Diagnostic Radiologic Technology. Final Report.

ERIC Educational Resources Information Center

Educational Testing Service, Princeton, NJ.

The validity of the Proficiency Examination for Diagnostic Radiologic Technology was investigated, using 140 radiologic technologists who took both the written Proficiency Examination and a performance test. As an additional criterion measure of job proficiency, supervisors' assessments were obtained for 128 of the technologists. The resulting…

WORK PLAN FOR COMPLETING A TECHNOLOGY ASSESSMENT OF WESTERN ENERGY RESOURCE DEVELOPMENT

EPA Science Inventory

This is a work plan for completing the final phase of a three year technology assessment of the development of six energy resources (coal, geothermal, natural gas, oil, oil shale, and uranium) in eight western states (Arizona, Colorado, Montana, New Mexico, North and South Dakota...

78 FR 78751 - Medicare Program; Physicians' Referrals to Health Care Entities With Which They Have Financial...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... records software or information technology and training services. The final rule for this exception was... involving interoperable electronic health records software or information technology and training services... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Medicare & Medicaid Services 42 CFR Part 411...

Technology-Oriented Job Preparation. Final Report.

ERIC Educational Resources Information Center

One America, Inc., Washington, DC.

An extensive review of literature dealing with 263 technology-oriented vocational training programs was conducted to gather current information on the state of such training. Particular emphasis was placed on links between programs and government bodies or private sector entities and programs that could serve as models for those wishing to…

Main Science and Technology Indicators, Volume 2012, Issue 2

ERIC Educational Resources Information Center

OECD Publishing (NJ3), 2013

2013-01-01

This biannual publication provides a set of indicators that reflect the level and structure of the efforts undertaken by OECD member countries and seven non-member economies (Argentina, China, Romania, Russian Federation, Singapore, South Africa, Chinese Taipei) in the field of science and technology. These data include final or provisional…

Composite Technology Personnel Development. Final Report.

ERIC Educational Resources Information Center

Massuda, Rachel; Fink, Edwin

A project was conducted at Delaware County Community College, Media, Pennsylvania, to train two instructional staff members in the area of composite materials technology. A 1-year training program was set up for the two technical instructional specialists at the Boeing Helicopter Training Center, Eddystone, Pennsylvania. The program consisted of…

Academic performance in a pharmacotherapeutics course sequence taught synchronously on two campuses using distance education technology.

PubMed

Steinberg, Michael; Morin, Anna K

2011-10-10

To compare the academic performance of campus-based students in a pharmacotherapeutics course with that of students at a distant campus taught via synchronous teleconferencing. Examination scores and final course grades for campus-based and distant students completing the case-based pharmacotherapeutics course sequence over a 5-year period were collected and analyzed. The mean examination scores and final course grades were not significantly different between students on the 2 campuses. The use of synchronous distance education technology to teach students does not affect students' academic performance when used in an active-learning, case-based pharmacotherapeutics course.

Technology to Reduce Hypoglycemia.

PubMed

Yeoh, Ester; Choudhary, Pratik

2015-07-01

Hypoglycemia is a major barrier toward achieving glycemic targets and is associated with significant morbidity (both psychological and physical) and mortality. This article reviews technological strategies, from simple to more advanced technologies, which may help prevent or mitigate exposure to hypoglycemia. More efficient insulin delivery systems, bolus advisor calculators, data downloads providing information on glucose trends, continuous glucose monitoring with alarms warning of hypoglycemia, predictive algorithms, and finally closed loop insulin delivery systems are reviewed. The building blocks to correct use and interpretation of this range of available technology require patient education and appropriate patient selection. © 2015 Diabetes Technology Society.

Database security and encryption technology research and application

NASA Astrophysics Data System (ADS)

Zhu, Li-juan

2013-03-01

The main purpose of this paper is to discuss the current database information leakage problem, and discuss the important role played by the message encryption techniques in database security, As well as MD5 encryption technology principle and the use in the field of website or application. This article is divided into introduction, the overview of the MD5 encryption technology, the use of MD5 encryption technology and the final summary. In the field of requirements and application, this paper makes readers more detailed and clearly understood the principle, the importance in database security, and the use of MD5 encryption technology.

Final Tier 2 Environmental Impact Statement for International Space Station

NASA Technical Reports Server (NTRS)

1996-01-01

The Final Tier 2 Environmental Impact Statement (EIS) for the International Space Station (ISS) has been prepared by the National Aeronautics and Space Administration (NASA) and follows NASA's Record of Decision on the Final Tier 1 EIS for the Space Station Freedom. The Tier 2 EIS provides an updated evaluation of the environmental impacts associated with the alternatives considered: the Proposed Action and the No-Action alternative. The Proposed Action is to continue U.S. participation in the assembly and operation of ISS. The No-Action alternative would cancel NASA!s participation in the Space Station Program. ISS is an international cooperative venture between NASA, the Canadian Space Agency, the European Space Agency, the Science and Technology Agency of Japan, the Russian Space Agency, and the Italian Space Agency. The purpose of the NASA action would be to further develop human presence in space; to meet scientific, technological, and commercial research needs; and to foster international cooperation.

2015 Edition Health Information Technology (Health IT) Certification Criteria, 2015 Edition Base Electronic Health Record (EHR) Definition, and ONC Health IT Certification Program Modifications. Final rule.

PubMed

2015-10-16

This final rule finalizes a new edition of certification criteria (the 2015 Edition health IT certification criteria or "2015 Edition'') and a new 2015 Edition Base Electronic Health Record (EHR) definition, while also modifying the ONC Health IT Certification Program to make it open and accessible to more types of health IT and health IT that supports various care and practice settings. The 2015 Edition establishes the capabilities and specifies the related standards and implementation specifications that Certified Electronic Health Record Technology (CEHRT) would need to include to, at a minimum, support the achievement of meaningful use by eligible professionals (EPs), eligible hospitals, and critical access hospitals (CAHs) under the Medicare and Medicaid EHR Incentive Programs (EHR Incentive Programs) when such edition is required for use under these programs.

Guiding the process of health technology disinvestment.

PubMed

Ibargoyen-Roteta, Nora; Gutiérrez-Ibarluzea, Iñaki; Asua, José

2010-12-01

To develop a guideline for health technology disinvestment. The Nominal Group Technique was used to determine relevant aspects of disinvestment decision-making. Ideas reaching consensus and previous Spanish guidelines on the acquisition of new health technologies (GANT) and new genetic tests (GEN) structures were used to develop the domains and contents of GuNFT (Guideline for Not Funding Health Technologies). The draft was peer reviewed by local and international experts and their suggestions were incorporated to the first GuNFT version. Thirty-five ideas reached consensus. The most relevant ones referred to the reasons for disinvesting in a technology and the key aspects that would facilitate disinvestment acceptance. Considering both consensus ideas and GANT and GEN guidelines, the first GuNFT draft was elaborated. After the review process, section numbers and contents were changed. The resulting GuNFT guideline was finally divided into six domains related to: (1) general preliminary recommendations, (2) completing the application form, (3) checking and prioritising applications, (4) assessment, (5) final decision and (6) action plan design. A software was also developed to facilitate GuNFT implementation. Disinvestment should be a guided process. Accordingly, we present the first guideline for that purpose. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

78 FR 13666 - Application for Final Commitment for a Long-Term Loan or Financial Guarantee in Excess of $100...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... the exportation of goods or provision of services by a United States industry. Parties: Principal Supplier(s): Space Systems/Loral Inc. Space Exploration Technologies Corporation. Obligor: Asia Satellite... services, U.S. launch services and launch insurance. Information On Decision: Information on the final...

77 FR 9625 - Presentation of Final Conventional Conformance Test Criteria and Common Air Interface (CAI...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-17

... Tests for Inclusion in the Program AGENCY: National Institute of Standards and Technology (NIST... meeting is to present the final requirements for CAI conventional conformance tests for inclusion in the... suitability for inclusion in the P25 CAP is below: Conformance tests should limit devices in the test...

Project CREATE Final Report. Cooperative Resources To Enhance Access to Technology Education.

ERIC Educational Resources Information Center

Hampden County Employment and Training Consortium, Springfield, MA.

These materials have been developed by Project CREATE (Cooperative Resources to Enhance Access to Jobs through Technical Education), a demonstration program designed to develop a network, specific activities, and resources that would provide education and support services to a wide audience. A 13-page final report describes the hands-on training…

Health Informatics Scientists' Perception About Big Data Technology.

PubMed

Minou, John; Routsis, Fotios; Gallos, Parisis; Mantas, John

2017-01-01

The aim of this paper is to present the perceptions of the Health Informatics Scientists about the Big Data Technology in Healthcare. An empirical study was conducted among 46 scientists to assess their knowledge about the Big Data Technology and their perceptions about using this technology in healthcare. Based on the study findings, 86.7% of the scientists had knowledge of Big data Technology. Furthermore, 59.1% of the scientists believed that Big Data Technology refers to structured data. Additionally, 100% of the population believed that Big Data Technology can be implemented in Healthcare. Finally, the majority does not know any cases of use of Big Data Technology in Greece while 57,8% of the them mentioned that they knew use cases of the Big Data Technology abroad.

United Nations Command Armistice Roles on the Korean Peninsula: Is December 2015 the End?

DTIC Science & Technology

2013-06-14

effect, both sides have modified security arrangements to meet changes in the diplomatic, economic, and technological environments. In the north, DPRK...practice, the Korean War remains without a final resolution. The KWAA provided a ceasefire for the two sides to reach a final political arrangement to...entrusted to the U.S. from time the UNC was established. Finally , the UNC became a crucial operational mechanism in the Armistice regime, which

75 FR 2013 - Health Information Technology: Initial Set of Standards, Implementation Specifications, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-13

...The Department of Health and Human Services (HHS) is issuing this interim final rule with a request for comments to adopt an initial set of standards, implementation specifications, and certification criteria, as required by section 3004(b)(1) of the Public Health Service Act. This interim final rule represents the first step in an incremental approach to adopting standards, implementation specifications, and certification criteria to enhance the interoperability, functionality, utility, and security of health information technology and to support its meaningful use. The certification criteria adopted in this initial set establish the capabilities and related standards that certified electronic health record (EHR) technology will need to include in order to, at a minimum, support the achievement of the proposed meaningful use Stage 1 (beginning in 2011) by eligible professionals and eligible hospitals under the Medicare and Medicaid EHR Incentive Programs.

Development of an Innovative Laser-Assisted Coating Process for Extending Lifetime of Metal Casting Dies. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madhav Rao Gonvindaraju

1999-10-18

Die casting dies used in the metal casting industry fail due to thermal fatigue cracking accompanied by the presence of residual tensile stresses, corrosion, erosion and wear of die surfaces. This phase 1 SBIR Final Report summarize Karta Technologies research involving the development of an innovative laser coating technology for metal casting dies. The process involves depositing complex protective coatings of nanocrystalline powders of TiC followed by a laser shot peening. The results indicate a significant improvement in corrosion and erosion resistance in molten aluminum for H13 die casting die steels. The laser-coated samples also showed improved surface finish, amore » homogeneous and uniform coating mircrostructure. The technology developed in this research can have a significant impact on the casting industry by saving the material costs involved in replacing dies, reducing downtime and improving the quality.« less

MPT_DOE Final Report 12-15-16 rev1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bunce, Michael

The goal of this project was to achieve breakthrough thermal efficiency on a light duty passenger car engine, with minimal impact to emissions. The enabling technology or technologies were to be relatively low cost and integrateable into existing production processes. Through the use of Turbulent Jet Ignition (TJI), an enabling technology for ultra-lean engine operation, the project team was able to meet or exceed all technical goals of this program.

Comparison of radar and infrared distance sensors for intelligent cruise control systems

NASA Astrophysics Data System (ADS)

Hoess, Alfred; Hosp, Werner; Rauner, Hans

1995-09-01

In this paper, infrared distance sensors are compared regarding technology, environmental, and practical aspects. Different methods for obtaining lateral resolution and covering the required detection range are presented for both sensor technologies. Possible positions for sensor installation at the test vehicle have been tested. Experimental results regarding cleaning devices and other environmental problems are presented. Finally, future aspects, e.g. speed over ground measurements or technological steps are discussed.

Live from Space Station Learning Technologies Project

NASA Technical Reports Server (NTRS)

2001-01-01

This is the Final Report for the Live From Space Station (LFSS) project under the Learning Technologies Project FY 2001 of the MSFC Education Programs Department. AZ Technology, Inc. (AZTek) has developed and implemented science education software tools to support tasks under the LTP program. Initial audience consisted of 26 TreK in the Classroom schools and thousands of museum visitors to the International Space Station: The Earth Tour exhibit sponsored by Discovery Place museum.

Use of mobile learning technology among final year medical students in Kenya

PubMed Central

Masika, Moses Muia; Omondi, Gregory Barnabas; Natembeya, Dennis Simiyu; Mugane, Ephraim Mwatha; Bosire, Kefa Ogonyo; Kibwage, Isaac Ongubo

2015-01-01

Introduction Mobile phone penetration has increased exponentially over the last decade as has its application in nearly all spheres of life including health and medical education. This study aimed at assessing the use of mobile learning technology and its challenges among final year undergraduate students in the College of Health sciences, University of Nairobi. Methods This was a cross-sectional descriptive study conducted among final year undergraduate students at the University of Nairobi, College of Health Sciences. Self-administered, anonymous questionnaires were issued to all final year students in their lecture rooms after obtaining informed consent. Data on demographics, mobile device ownership and mobile learning technology use and its challenges was collected. Data entry and analysis was done using SPSS®. Chi-square and t-test were used for bivariate analysis. Results We had 292 respondents; 62% were medical students, 16% were nursing students, 13% were pharmacy students and 9% were dental surgery students. The majority were female (59%) and the average age was 24 years. Eighty eight percent (88%) of the respondents owned a smart device and nearly all of them used it for learning. 64% of the respondents used medical mobile applications. The main challenges were lack of a smart device, lack of technical know-how in accessing or using apps, sub-optimal internet access, cost of acquiring apps and limited device memory. Conclusion Mobile learning is increasingly popular among medical students and should be leveraged in promoting access and quality of medical education. PMID:26327964

Use of mobile learning technology among final year medical students in Kenya.

PubMed

Masika, Moses Muia; Omondi, Gregory Barnabas; Natembeya, Dennis Simiyu; Mugane, Ephraim Mwatha; Bosire, Kefa Ogonyo; Kibwage, Isaac Ongubo

2015-01-01

Mobile phone penetration has increased exponentially over the last decade as has its application in nearly all spheres of life including health and medical education. This study aimed at assessing the use of mobile learning technology and its challenges among final year undergraduate students in the College of Health sciences, University of Nairobi. This was a cross-sectional descriptive study conducted among final year undergraduate students at the University of Nairobi, College of Health Sciences. Self-administered, anonymous questionnaires were issued to all final year students in their lecture rooms after obtaining informed consent. Data on demographics, mobile device ownership and mobile learning technology use and its challenges was collected. Data entry and analysis was done using SPSS(®). Chi-square and t-test were used for bivariate analysis. We had 292 respondents; 62% were medical students, 16% were nursing students, 13% were pharmacy students and 9% were dental surgery students. The majority were female (59%) and the average age was 24 years. Eighty eight percent (88%) of the respondents owned a smart device and nearly all of them used it for learning. 64% of the respondents used medical mobile applications. The main challenges were lack of a smart device, lack of technical know-how in accessing or using apps, sub-optimal internet access, cost of acquiring apps and limited device memory. Mobile learning is increasingly popular among medical students and should be leveraged in promoting access and quality of medical education.

Technology to Reduce Hypoglycemia

PubMed Central

Yeoh, Ester; Choudhary, Pratik

2015-01-01

Hypoglycemia is a major barrier toward achieving glycemic targets and is associated with significant morbidity (both psychological and physical) and mortality. This article reviews technological strategies, from simple to more advanced technologies, which may help prevent or mitigate exposure to hypoglycemia. More efficient insulin delivery systems, bolus advisor calculators, data downloads providing information on glucose trends, continuous glucose monitoring with alarms warning of hypoglycemia, predictive algorithms, and finally closed loop insulin delivery systems are reviewed. The building blocks to correct use and interpretation of this range of available technology require patient education and appropriate patient selection. PMID:25883167

Alaska's renewable energy potential.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2009-02-01

This paper delivers a brief survey of renewable energy technologies applicable to Alaska's climate, latitude, geography, and geology. We first identify Alaska's natural renewable energy resources and which renewable energy technologies would be most productive. e survey the current state of renewable energy technologies and research efforts within the U.S. and, where appropriate, internationally. We also present information on the current state of Alaska's renewable energy assets, incentives, and commercial enterprises. Finally, we escribe places where research efforts at Sandia National Laboratories could assist the state of Alaska with its renewable energy technology investment efforts.

Make or Buy: Cost Impacts of Additive Manufacturing, 3D Laser Scanning Technology, and Collaborative Product Lifecycle Management on Ship Maintenance and Modernization

DTIC Science & Technology

2015-05-01

management during operations 4 Potential Technology 3: Additive Manufacturing (“ 3D Printing ”) 5 • 3D design/image (e.g. from 3D LS) of final part...1 Make or Buy: Cost Impacts of Additive Manufacturing, 3D Laser Scanning Technology, and Collaborative Product Lifecycle Management on Ship...DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Make or Buy: Cost Impacts of Additive Manufacturing, 3D Laser Scanning Technology

Health technology assessment in Switzerland: a descriptive analysis of “Coverage with Evidence Development” decisions from 1996 to 2013

PubMed Central

Brügger, Urs; Horisberger, Bruno; Ruckstuhl, Alexander; Plessow, Rafael; Eichler, Klaus; Gratwohl, Alois

2015-01-01

Objectives To identify factors associated with the decisions of the Federal Department of Home Affairs concerning coverage with evidence development (CED) for contested novel medical technologies in Switzerland. Design Quantitative, retrospective, descriptive analysis of publicly available material and prospective, structured, qualitative interviews with key stakeholders. Setting All 152 controversial medical services decided on by the Federal Commission on Health Insurance Benefits within the framework of the new federal law on health insurance in Switzerland from 1997 to 2013, with focus on 33 technologies assigned initially to CED and 33 to evidence development without coverage. Main outcome measures Factors associated with numbers and type of contested services assigned to CED per year, the duration and final outcome of the evaluations and perceptions of key stakeholders. Results The rate of CED decisions (82 total; median 1.5/year; range 0–9/year), the time to final decision (4.5 years median; 0.75 to +11 years) and the probability of a final ‘yes’ varied over time. In logistic regression models, the change of office of the commission provided the best explanation for the observed outcomes. Good intentions but absence of scientific criteria for decisions were reported as major comments by the stakeholders. Conclusions The introduction of CED enabled access to some promising technologies early in their life cycle, and might have triggered establishment of registries and research. Impact on patients’ outcome and costs remain unknown. The primary association of institutional changes with measured end points illustrates the need for evaluation of the current health technology assessment (HTA) system. PMID:25818273

Health and Wellness Technology Use by Historically Underserved Health Consumers: Systematic Review

PubMed Central

Perchonok, Jennifer

2012-01-01

Background The implementation of health technology is a national priority in the United States and widely discussed in the literature. However, literature about the use of this technology by historically underserved populations is limited. Information on culturally informed health and wellness technology and the use of these technologies to reduce health disparities facing historically underserved populations in the United States is sparse in the literature. Objective To examine ways in which technology is being used by historically underserved populations to decrease health disparities through facilitating or improving health care access and health and wellness outcomes. Methods We conducted a systematic review in four library databases (PubMed, PsycINFO, Web of Science, and Engineering Village) to investigate the use of technology by historically underserved populations. Search strings consisted of three topics (eg, technology, historically underserved populations, and health). Results A total of 424 search phrases applied in the four databases returned 16,108 papers. After review, 125 papers met the selection criteria. Within the selected papers, 30 types of technology, 19 historically underserved groups, and 23 health issues were discussed. Further, almost half of the papers (62 papers) examined the use of technology to create effective and culturally informed interventions or educational tools. Finally, 12 evaluation techniques were used to assess the technology. Conclusions While the reviewed studies show how technology can be used to positively affect the health of historically underserved populations, the technology must be tailored toward the intended population, as personally relevant and contextually situated health technology is more likely than broader technology to create behavior changes. Social media, cell phones, and videotapes are types of technology that should be used more often in the future. Further, culturally informed health information technology should be used more for chronic diseases and disease management, as it is an innovative way to provide holistic care and reminders to otherwise underserved populations. Additionally, design processes should be stated regularly so that best practices can be created. Finally, the evaluation process should be standardized to create a benchmark for culturally informed health information technology. PMID:22652979

Examining Factors Affecting Beginning Teachers' Transfer of Learning of ICT-Enhanced Learning Activities in Their Teaching Practice

ERIC Educational Resources Information Center

Agyei, Douglas D.; Voogt, Joke

2014-01-01

This study examined 100 beginning teachers' transfer of learning when utilising Information Communication Technology-enhanced activity-based learning activities. The beginning teachers had participated in a professional development program that was characterised by "learning technology by collaborative design" in their final year of…

Educational Technology, E.C.I.A. Chapter 2. Final Evaluation Report.

ERIC Educational Resources Information Center

District of Columbia Public Schools, Washington, DC. Div. of Quality Assurance.

The Planning, Monitoring and Implementing (PMI) Evaluation Model for Decision-Making was used by the District of Columbia Public Schools to monitor their Office of Educational Technology in its efforts to provide direction and coordination for computer related activities, and to plan and implement educational television projects in math and…

Overcoming Barriers To IVHS -- Lessons From Other Technologies, Final Task F Report, Model Advanced Traffic Management System Franchise Agreement

DOT National Transportation Integrated Search

1995-08-25

VIABLE ADVANCED TRAFFIC MANAGEMENT SYSTEMS WILL BE CENTRAL TO THE : DEVELOPMENT OF ITS TECHNOLOGIES, AND CRITICAL TO THE DELIVERY OF MANY PRIVATE SECTOR ITS SERVICES TO THE PUBLIC. BY ITS VERY NATURE, HOWEVER, ATMS RELIES HEAVILY ON ACCESS TO THE PUB...

76 FR 33166 - Defense Federal Acquisition Regulation Supplement (DFARS); Warranty Tracking of Serialized Items...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-08

... Acquisition, Technology and Logistics dated February 6, 2007, which required definition of the requirements to... Defense for Acquisition, Technology and Logistics issued a policy memorandum dated February 6, 2007, which... Changes Required During the final rule development, DoD restructured the layout of the rule to reduce...

The Challenge to Situate Digital Learning Technologies in Preservice Teacher Mathematics Education

ERIC Educational Resources Information Center

McDonald, Susan

2012-01-01

This paper focuses on how preservice primary teachers can be supported to embrace digital learning technologies (DLTs) in their teaching of mathematics. The nature of the instruction and the assessment in the final mathematics unit of the bachelor of education program were changed. Despite being tagged as "tech-savvy," preservice…

Evaluation of the Science, Technology, and Engineering Leadership Program, Year Three

ERIC Educational Resources Information Center

Wolanin, Natalie; Wade, Julie

2014-01-01

The Office of Shared Accountability conducted an evaluation of the implementation of the third and final year (2012-2013) of the "Science, Technology, and Engineering Leadership Program" (STELP) in Montgomery County (Maryland) Public Schools (MCPS). Funding for STELP, including the evaluation study, is provided by a grant from the Howard…

Social Media as a Learning Technology for University Students

ERIC Educational Resources Information Center

Hussain, Irshad; Cakir, Ozlem; Candeger, Ümmügülsüm

2018-01-01

This paper demonstrates the role of social media as a learning technology for university students and highlights their problems associated with its use. The population of the study consisted of Masters' and Bachelor Studies students studying in their final semesters in the departments of Social Sciences at The Islamia University of Bahawalpur,…

The Effect of Using E-Learning Tools in Online and Campus-Based Classrooms on Student Performance

ERIC Educational Resources Information Center

Galy, Edith; Downey, Clara; Johnson, Jennie

2011-01-01

Creating an integrative research framework that extends a model frequently used in the Information Systems field, the Technology Acceptance Model, together with variables used in the Education field, this empirical study investigates the factors influencing student performance as reflected by their final course grade. The Technology Acceptance…

Development of Articulated Competency-Based Curriculum in Laser/Electro-Optics Technology. Final Report.

ERIC Educational Resources Information Center

Luzerne County Community Coll., Nanticoke, PA.

A project was conducted at the Community College of Luzerne County (Pennsylvania) to develop, in cooperation with area vocational-technical schools, the first year of a competency-based curriculum in laser/electro-optics technology. Existing programs were reviewed and private sector input was sought in developing the curriculum and identifying…

The Boeing Company's Manufacturing Technology Student Internship. Final Evaluation Report for 1996.

ERIC Educational Resources Information Center

Owens, Tom

A study evaluated The Boeing Company's Student Internship Program for students enrolled in a manufacturing technology program. The programs in the Seattle (Washington) and Portland (Oregon) areas provided students with three progressive internship levels offered in the summers of grades 11, 12, and 13 (the first year of community college). The…

40 CFR 192.31 - Definitions and cross-references.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requirements of § 192.32(b)(1) of this subpart apply. (g) Regulatory agency means the U.S. Nuclear Regulatory... physical characteristics of the tailings and the site; the limits of available technology; the need for... provided for by use of the term “available technology.” (l) Permanent Radon Barrier means the final radon...

40 CFR 192.31 - Definitions and cross-references.

Code of Federal Regulations, 2011 CFR

2011-07-01

... requirements of § 192.32(b)(1) of this subpart apply. (g) Regulatory agency means the U.S. Nuclear Regulatory... physical characteristics of the tailings and the site; the limits of available technology; the need for... provided for by use of the term “available technology.” (l) Permanent Radon Barrier means the final radon...

Area Consortium on Training. "Training for Technology" Project, 1982-1983. Final Report.

ERIC Educational Resources Information Center

Moock, Lynn D.

The Area Consortium on Training initiated the Training for Technology Project to fill industry needs for skilled personnel and job needs for economically disadvantaged persons. Major accomplishments included establishment of a training team for economic development and for development of training programs; contacting of more than 100 employers;…

Evaluation and Dissemination of the Electrical Power Engineering Technology Curriculum Model. Final Report.

ERIC Educational Resources Information Center

McNeill, Perry R.; And Others

Described is a project initiated to evaluate and disseminate the Electrical Power Engineering Technology Curriculum developed at Oklahoma State University. The objective of the evaluation phase, to have the original model curriculum evaluated by both present and potential employers, was accomplished in a two-day workshop with participation of…

Electro-Optical Laser Technology. Curriculum Utilization. Final Report.

ERIC Educational Resources Information Center

Nawn, John H.

This report describes a program to prepare students for employment as laser technicians and laser operators and to ensure that they have the necessary skills required by the industry. The objectives are to prepare a curriculum and syllabus for an associate degree program in Electro-Optical Laser Technology. The 2-year Electro-Optical Laser program…

Commercial Supersonics Technology Project - Status of Airport Noise

NASA Technical Reports Server (NTRS)

Bridges, James

2016-01-01

The Commercial Supersonic Technology Project has been developing databases, computational tools, and system models to prepare for a level 1 milestone, the Low Noise Propulsion Tech Challenge, to be delivered Sept 2016. Steps taken to prepare for the final validation test are given, including system analysis, code validation, and risk reduction testing.

Information Technology Research: Investing in Our Future. Report to the President.

ERIC Educational Resources Information Center

National Coordination Office for Information Technology Research and Development, Arlington, VA.

This is the final report on future directions for Federal support of research and development (R&D) for information technology. This report adds detail to the findings and recommendations in the interim report dated August 1998, and strengthens previous recommendations regarding the importance of social and economic research on the impacts of…

Cybernation and Man--A Course Development Project; Report Number 2. Final Report.

ERIC Educational Resources Information Center

Dionne, Edward A.; Parkman, Ralph

Transportation, Agriculture, and Art are used as examples to establish how technology, especially computer-based technology, is involved in the life of man. Cities grow in population very rapidly; motor vehicles grow in number even more rapidly; both citcumstances raise problems--traffic congestion, economic loss, air pollution, urban…

78 FR 79201 - Medicare and State Health Care Programs: Fraud and Abuse; Electronic Health Records Safe Harbor...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-27

... interoperable electronic health records software or information technology and training services. The final rule... information technology and training services necessary and used predominantly to create, maintain, transmit... ordering of, any good, facility, service, or item reimbursable by any Federal health care program. Because...

Computer Software for Forestry Technology Curricula. Final Report.

ERIC Educational Resources Information Center

Watson, Roy C.; Scobie, Walter R.

Since microcomputers are being used more and more frequently in the forest products industry in the Pacific Northwest, Green River Community College conducted a project to search for BASIC language computer programs pertaining to forestry, and when possible, to adapt such software for use in teaching forestry technology. The search for applicable…

On board processor development for NASA's spaceborne imaging radar with system-on-chip technology

NASA Technical Reports Server (NTRS)

Fang, Wai-Chi

2004-01-01

This paper reports a preliminary study result of an on-board spaceborne SAR processor. It consists of a processing requirement analysis, functional specifications, and implementation with system-on-chip technology. Finally, a minimum version of this on-board processor designed for performance evaluation and for partial demonstration is illustrated.

FINAL REPORT, USE OF 1) SENSORS AND 2)RADIO FREQUENCY ID (RFID) FOR THE NATIONAL CHILDREN'S STUDY

EPA Science Inventory

Recent advancements in technology have provided new tools that researchers can use to collect data more easily and reduce participant burden. In what ways will this new technology impact researchers and participants? Imagine a scenario where a small child is playing outside of hi...

Advanced Technology Tech Prep Partnership for Northern Kane Regional Delivery System. Final Report.

ERIC Educational Resources Information Center

Elgin Community Coll., IL.

A 1-year project was undertaken to continue implementation, evaluation, and revision of a model advanced technology partnership between Elgin Community College (ECC) and the Northern Kane Regional Delivery System in Illinois. The model program, which originally included three high schools, was expanded to include five additional high schools in…

Measurement of centering error for probe of swing arm profilometer using a spectral confocal sensor

NASA Astrophysics Data System (ADS)

Chen, Lin; Jing, Hongwei; Wei, Zhongwei; Cao, Xuedong

2015-02-01

A spectral confocal sensor was used to measure the centering error for probe of swing arm profilometer (SAP). The feasibility of this technology was proved through simulation and experiment. The final measurement results was also analyzed to evaluate the advantages and disadvantages of this technology.

77 FR 41697 - Stay of the Effectiveness of Requirements; Approval and Promulgation of Implementation Plans; New...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-16

... Technology Determination AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: The EPA... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 52 [EPA-R06-OAR-2010-0846; FRL-9698-3] Stay of the... Visibility and Best Available Retrofit Technology Determination'' under the authority of the Administrative...

Potential Applications and Impact of Microelectronic and Telecommunication Technology in Health Care Delivery. Final Report.

ERIC Educational Resources Information Center

Mandex, Inc., Vienna, VA.

This compendium of current and recent innovative methods of health care delivery focuses on telemedicine, and educational and energy management and control applications. Each application is doumented in a project abstract describing the system and the technology employed, and citing relevant information sources and a personal or organizational…

Design of Training Systems. Computerization of the Educational Technology Assessment Model. Volume 1.

ERIC Educational Resources Information Center

Duffy, Larry B.; And Others

The Educational Technology Assessment Model (ETAM) is a set of comprehensive procedures and variables for the analysis, synthesis, and decision making, in regard to the benefits, costs, and risks associated with introducing technical innovations in education and training. This final report summarizes the analysis, design, and development…

78 FR 21314 - Medicare and State Health Care Programs: Fraud and Abuse; Electronic Health Records Safe Harbor...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-10

... health records software or information technology and training services. The final rule for this safe... health records software or information technology and training services. In the same issue of the Federal..., licenses, and intellectual property related to electronic health records software; connectivity services...

Mileage-based user fees : defining a path toward implementation phase 2, an assessment of technology issues : final report

DOT National Transportation Integrated Search

2009-10-01

This report reviews technology options for a mileage-based user fee system in the state of Texas. The report was : compiled based on input from a diverse range of sources, including a literature review of existing mileage-based : user fee technical w...

High Technology Internship at the Secondary Level. Final Report.

ERIC Educational Resources Information Center

Noll, Clifford J.

A program was conducted during the Spring semester, 1985, in the San Antonio area to place high school juniors and seniors from three high schools in the Edgewood Independent School District in three-month interships in high-technology industries. Students traveled to their training locations on school-provided transportation on Mondays through…

75 FR 44589 - Health Information Technology: Initial Set of Standards, Implementation Specifications, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

..., one of which included the ``use of certified EHR technology in a meaningful manner.'' This means that... comments received by ONC related to the Interim Final Rule. In some cases, due to the simultaneous... or eligible hospital would be required to use adopted standards. One commenter specifically requested...

76 FR 68503 - Winter Use Plan, Final Environmental Impact Statement, Yellowstone National Park, Idaho, Montana...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... to 318 commercially guided, best available technology snowmobiles and 78 commercially guided... available technology snowmobiles and 78 commercially guided snowcoaches would be allowed in the park per day... and a detailed history of winter use in Yellowstone, is available at http://www.nps.gov/yell/planvisit...

A Forest Products Technology Program for Washington Community Colleges. Final Report.

ERIC Educational Resources Information Center

Grotefend, Robert T.

This report describes a project to develop a forest product technology curriculum that prepares students at the technical level, junior management, to work in the manufacturing of wood and bark into lumber, plywood, particle board, laminates, and pulp chips. Chapter 1 describes project objectives and procedures followed. In chapter 2 the history…

The web-rhetoric of companies offering home-based personal health monitoring.

PubMed

Nordgren, Anders

2012-06-01

In this paper I investigate the web-rhetoric of companies offering home-based personal health monitoring to patients and elderly people. Two main rhetorical methods are found, namely a reference to practical benefits and a use of prestige words like "quality of life" and "independence". I interpret the practical benefits in terms of instrumental values and the prestige words in terms of final values. I also reconstruct the arguments on the websites in terms of six different types of argument. Finally, I articulate a general critique of the arguments, namely that the websites neglect the context of use of personal health monitoring technologies. Whether or not a technology is good depends on the use of the technology by a particular individual in a particular context. The technology is not good-or bad-in itself. I support this critique with a number of more specific arguments such as the risk for reduced personal contact. For some elderly people social contact with care providers is more valuable than the independent living made possible by remote monitoring, for others independence is more important.

Study of Collaborative Management for Transportation Construction Project Based on BIM Technology

NASA Astrophysics Data System (ADS)

Jianhua, Liu; Genchuan, Luo; Daiquan, Liu; Wenlei, Li; Bowen, Feng

2018-03-01

Abstract. Building Information Modeling(BIM) is a building modeling technology based on the relevant information data of the construction project. It is an advanced technology and management concept, which is widely used in the whole life cycle process of planning, design, construction and operation. Based on BIM technology, transportation construction project collaborative management can have better communication through authenticity simulation and architectural visualization and can obtain the basic and real-time information such as project schedule, engineering quality, cost and environmental impact etc. The main services of highway construction management are integrated on the unified BIM platform for collaborative management to realize information intercommunication and exchange, to change the isolated situation of information in the past, and improve the level of information management. The final BIM model is integrated not only for the information management of project and the integration of preliminary documents and design drawings, but also for the automatic generation of completion data and final accounts, which covers the whole life cycle of traffic construction projects and lays a good foundation for smart highway construction.

Flippin' Fluid Mechanics - Using Online Technology to Enhance the In-Class Learning Experience

NASA Astrophysics Data System (ADS)

Webster, D. R.; Majerich, D. M.

2013-11-01

This study provides an empirical analysis of using online technologies and team problem solving sessions to shift an undergraduate fluid mechanics course from a traditional lecture format to a collaborative learning environment. Students were from two consecutive semesters of the same course taught by the same professor. One group used online technologies and solved problems in class and the other did not. Out of class, the treatment group watched 72 short (11 minutes, average) video lectures covering course topics and example problems being solved. Three times a week students worked in teams of two to solve problems on desktop whiteboard tablets while the instructor and graduate assistants provided ``just-in-time'' tutoring. The number of team problems assigned during the semester exceeded 100. Weekly online homework was assigned to reinforce topics. The WileyPlus online system generated unique problem parameters for each student. The control group received three-50 minute weekly lectures. Data include three midterms and a final exam. Regression results indicate that controlling for all of the entered variables, for every one more problem solving session the student attended, the final grade was raised by 0.327 points. Thus, if a student participated in all 25 of the team problem solving sessions, the final grade would have been 8.2 points higher, a difference of nearly a grade. Using online technologies and teamwork appeared to result in improved achievement, but more research is needed to support these findings.

Programmatic Research to Design and Develop Improved Instructional Technology for Handicapped Children. Final Report.

ERIC Educational Resources Information Center

Schiefelbusch, Richard L.; Lent, James R.

Presented is the final report for Project MORE (Mediated Operational Research for Education), a program to create a full-scale operational system for developing product prototypes (methods and materials packages) for teaching personal appearance and hygiene skills to the trainable mentally retarded child. Reviewed in part I is the history of the…

California State Implementation Plan; Final Approval of Revision; Yolo-Solano Air Quality Management District; Reasonably Available Control Technology Requirements for 1997 8-hour Ozone NAAQS

EPA Pesticide Factsheets

EPA is taking final action to approve a revision to the Yolo-Solano Air Quality Management District (YSAQMD) portion of the California SIP concerning YSAQMD regarding RACT)requirements the 1997 8-hour ozone NAAQS and approve negative declarations into SIP.

78 FR 72641 - Request for Public Comments on Draft Final Report on the Technical Investigation of the May 22...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

..., 2011 Tornado in Joplin, Missouri AGENCY: National Institute of Standards and Technology, United States... for public comment of the draft final report of the investigation conducted by NIST into the tornado... found on the Joplin Investigation Web page http://www.nist.gov/el/disasterstudies/weather/joplin_tornado...

"Clickers" and HACCP: Educating a Diverse Food Industry Audience with Technology

ERIC Educational Resources Information Center

Shaw, Angela; Mendonca, Aubrey; Daraba, Aura

2015-01-01

Hazard Analysis Critical Control Points (HACCP) is a systematic approach to food safety education for the food industry. To receive a HACCP certificate, participants must receive an 80% or higher on the final examination. Language barriers, educational levels, and age have been noted as primary reasons for not passing the final examination.…

Capturing Cognitive Fingerprints for Active Authentication

DTIC Science & Technology

2014-10-01

CAPTURING COGNITIVE FINGERPRINTS FOR ACTIVE AUTHENTICATION IOWA STATE UNIVERSITY OF SCIENCE & TECHNOLOGY OCTOBER 2014 FINAL TECHNICAL REPORT...REPORT TYPE FINAL TECHNICAL REPORT 3. DATES COVERED (From - To) SEP 2013 – APR 2014 4. TITLE AND SUBTITLE CAPTURING COGNITIVE FINGERPRINTS FOR ACTIVE...The project ended before the IRB application was approved. 15. SUBJECT TERMS Active Authentication, Cognitive Fingerprints , Biometric Modalities

Hospitality Industry Technology Training (HITT). Final Performance Report, April 1, 1989-December 31, 1990.

ERIC Educational Resources Information Center

Mount Hood Community Coll., Gresham, OR.

This final performance report includes a third-party evaluation and a replication guide. The first section describes a project to develop and implement an articulated curriculum for grades 8-14 to prepare young people for entry into hospitality/tourism-related occupations. It discusses the refinement of existing models, pilot test, curriculum…

Examinations in the Final Year of Transition to Mathematical Methods Computer Algebra System (CAS)

ERIC Educational Resources Information Center

Leigh-Lancaster, David; Les, Magdalena; Evans, Michael

2010-01-01

2009 was the final year of parallel implementation for Mathematical Methods Units 3 and 4 and Mathematical Methods (CAS) Units 3 and 4. From 2006-2009 there was a common technology-free short answer examination that covered the same function, algebra, calculus and probability content for both studies with corresponding expectations for key…

Development of a Hydrologic Characterization Technology for Fault Zones Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karasaki, Kenzi; Onishi, Celia Tiemi; Doughty, Christine

2012-03-31

This is the final report for the five-year program of the NUMO-LBNL collaborative project (hereafter called the Project): Development of Hydrologic Characterization Technology for Fault Zones, under a NUMO-DOE/LBNL collaboration agreement. Detailed results from the past four years of study can be found in the each year’s year-end report (Karasaki et al., 2008, 2009, 2010, and 2011; Kiho et al., 2008, 2009, 2010, and 2011). In this report, we discuss the results of the studies conducted in FY2011. We also give a summary of the overall results and findings, as well as the lessons learned during the course of themore » Project.« less

Evaluation of laminar flow control system concepts for subsonic commercial transport aircraft

NASA Technical Reports Server (NTRS)

1979-01-01

Results of a 2-year study are reported which were carried out to extend the development of laminar flow control (LFC) technology and evaluate LFC systems concepts. The overall objective of the LFC program is to provide a sound basis for industry decisions on the application of LFC to future commercial transports. The study was organized into major tasks to support the stated objectives through application of LFC systems concepts to a baseline LFC transport initially generated for the study. Based on competitive evaluation of these concepts, a final selection was made for incorporation into the final design of an LFC transport which also included other advanced technology elements appropriate to the 1990 time period.

Identifying technology innovations for marginalized smallholders-A conceptual approach.

PubMed

Malek, Mohammad Abdul; Gatzweiler, Franz W; Von Braun, Joachim

2017-05-01

This paper adds a contribution in the existing literature in terms of theoretical and conceptual background for the identification of idle potentials of marginal rural areas and people by means of technological and institutional innovations. The approach follows ex-ante assessment for identifying suitable technology and institutional innovations for marginalized smallholders in marginal areas-divided into three main parts (mapping, surveying and evaluating) and several steps. Finally, it contributes to the inclusion of marginalized smallholders by an improved way of understanding the interactions between technology needs, farming systems, ecological resources and poverty characteristics in the different segments of the poor, and to link these insights with productivity enhancing technologies.

Application of harmonic detection technology in methane telemetry

NASA Astrophysics Data System (ADS)

Huo, Yuehua; Fan, Weiqiang

2017-08-01

Methane telemetry plays a vital role in ensuring the safe production of coal mines and monitoring the leakage of natural gas pipelines. Harmonic detection is the key technology of methane telemetry accuracy and sensitivity, but the current telemetry distance is short, the relationship between different modulation parameters is complex, and the harmonic signal is affected by noise interference. These factors seriously affect the development of harmonic detection technology. In this paper, the principle of methane telemetry based on harmonic detection technology is introduced. The present situation and characteristics of harmonic detection technology are expounded. The problems existing in harmonic detection are analyzed. Finally, the future development trend is discussed.

Micro guidance and control technology overview

NASA Technical Reports Server (NTRS)

Kissel, Glen J.; Hadaegh, Fred Y.

1993-01-01

This paper gives an overview of micro-guidance and control technologies and in the process previews of the technology/user and systems issues presented in the guidance and control session at the workshop. We first present a discussion of the advantages of using micro-guidance and control components and then detail six micro-guidance and control thrusts that could have a revolutionary impact on space missions and systems. Specific technologies emerging in the micro-guidance and control field will be examined. These technologies fall into two broad categories: micro-attitude determination (inertial and celestial) and micro-actuation, control and sensing. Finally, the scope of the workshop's guidance and control panel are presented.

IBM Cloud Computing Powering a Smarter Planet

NASA Astrophysics Data System (ADS)

Zhu, Jinzy; Fang, Xing; Guo, Zhe; Niu, Meng Hua; Cao, Fan; Yue, Shuang; Liu, Qin Yu

With increasing need for intelligent systems supporting the world's businesses, Cloud Computing has emerged as a dominant trend to provide a dynamic infrastructure to make such intelligence possible. The article introduced how to build a smarter planet with cloud computing technology. First, it introduced why we need cloud, and the evolution of cloud technology. Secondly, it analyzed the value of cloud computing and how to apply cloud technology. Finally, it predicted the future of cloud in the smarter planet.

National Alliance for Advanced Biofuels and Bio-Products Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olivares, Jose A.; Baxter, Ivan; Brown, Judith

2014-09-30

The main objective of NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. The approach was to address technology development across the entire value chain of algal biofuels production, from selection of strains to cultivation, harvesting, extraction, fuel conversion, and agricultural coproduct production. Sustainable practices and financial feasibility assessments ununderscored the approach and drove the technology development.

Precise time technology for selected Air Force systems: Present status and future requirements

NASA Technical Reports Server (NTRS)

Yannoni, N. F.

1981-01-01

Precise time and time interval (PTTI) technology is becoming increasingly significant to Air Force operations as digital techniques find expanded utility in military missions. Timing has a key role in the function as well as in navigation. A survey of the PTTI needs of several Air Force systems is presented. Current technology supporting these needs was reviewed and new requirements are emphasized for systems as they transfer from initial development to final operational deployment.

[Design and implementation on smart client for hospital information system].

PubMed

Liu, Min; Chen, Wei

2009-07-01

The article analyzes the traditional advantages and disadvantages of HIS based on the C/S and B/S structure, and introduces the features of Smart Client technology. Applying the technology in HIS, not only provides excellent operating experience, but also has the benefits of management brought about by concentration of deployment and update, achieve a balanced use of resources. Finally, this paper focuses on the application of the technology in the HIS system architecture design.

Surrogate Final Technical Report for "Solar: A Photovoltaic Manufacturing Development Facility"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farrar, Paul

2014-06-27

The project goal to create a first-of-a-kind crystalline Silicon (c-Si) photovoltaic (PV) Manufacturing & Technology Development Facility (MDF) that will support the growth and maturation of a strong domestic PV manufacturing industry, based on innovative and differentiated technology, by ensuring industry participants can, in a timely and cost-effective manner, access cutting-edge manufacturing equipment and production expertise needed to accelerate the transition of innovative technologies from R&D into manufacturing.

Projection displays and MEMS: timely convergence for a bright future

NASA Astrophysics Data System (ADS)

Hornbeck, Larry J.

1995-09-01

Projection displays and microelectromechanical systems (MEMS) have evolved independently, occasionally crossing paths as early as the 1950s. But the commercially viable use of MEMS for projection displays has been illusive until the recent invention of Texas Instruments Digital Light Processing TM (DLP) technology. DLP technology is based on the Digital Micromirror DeviceTM (DMD) microchip, a MEMS technology that is a semiconductor digital light switch that precisely controls a light source for projection display and hardcopy applications. DLP technology provides a unique business opportunity because of the timely convergence of market needs and technology advances. The world is rapidly moving to an all- digital communications and entertainment infrastructure. In the near future, most of the technologies necessary for this infrastrucutre will be available at the right performance and price levels. This will make commercially viable an all-digital chain (capture, compression, transmission, reception decompression, hearing, and viewing). Unfortunately, the digital images received today must be translated into analog signals for viewing on today's televisions. Digital video is the final link in the all-digital infrastructure and DLP technoogy provides that link. DLP technology is an enabler for digital, high-resolution, color projection displays that have high contrast, are bright, seamless, and have the accuracy of color and grayscale that can be achieved only by digital control. This paper contains an introduction to DMD and DLP technology, including the historical context from which to view their developemnt. The architecture, projection operation, and fabrication are presented. Finally, the paper includes an update about current DMD business opportunities in projection displays and hardcopy.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander Fridman

2005-06-01

This DOE project DE-FC36-04GO14052 ''Plasma Pilot Plant Test for Treating VOC Emissions from Wood Products Plants'' was conducted by Drexel University in cooperation with Georgia-Pacific (G-P) and Kurchatov Institute (KI). The objective of this project was to test the Plasma Pilot Plant capabilities in wood industry. The final goal of the project was to replace the current state-of-the-art, regenerative thermal oxidation (RTO) technology by Low-Temperature Plasma Technology (LTPT) in paper and wood industry for Volatile Organic Components (VOC) destruction in High Volume Low Concentration (HVLC) vent emissions. MetPro Corporation joined the team as an industrial partner from the environmental controlmore » business and a potential leader for commercialization. Concurrent Technology Corporation (CTC) has a separate contract with DOE for this technology evaluation. They prepared questionnaires for comparison of this technology and RTO, and made this comparison. These data are presented in this report along with the description of the technology itself. Experiments with the pilot plant were performed with average plasma power up to 3.6 kW. Different design of the laboratory and pilot plant pulsed coronas, as well as different analytical methods revealed many new peculiarities of the VOC abatement process. The work reported herein describes the experimental results for the VOCs removal efficiency with respect to energy consumption, residence time, water effect and initial concentration.« less

Industrial Sector Technology Use Model (ISTUM): industrial energy use in the United States, 1974-2000. Volume 4. Technology appendix. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-10-01

Volume IV of the ISTUM documentation gives information on the individual technology specifications, but relates closely with Chapter II of Volume I. The emphasis in that chapter is on providing an overview of where each technology fits into the general-model logic. Volume IV presents the actual cost structure and specification of every technology modeled in ISTUM. The first chapter presents a general overview of the ISTUM technology data base. It includes an explanation of the data base printouts and how the separate-cost building blocks are combined to derive an aggregate-technology cost. The remaining chapters are devoted to documenting the specific-technologymore » cost specifications. Technologies included are: conventional technologies (boiler and non-boiler conventional technologies); fossil-energy technologies (atmospheric fluidized bed combustion, low Btu coal and medium Btu coal gasification); cogeneration (steam, machine drive, and electrolytic service sectors); and solar and geothermal technologies (solar steam, solar space heat, and geothermal steam technologies), and conservation technologies.« less

The technology-science relationship: Some curriculum implications

NASA Astrophysics Data System (ADS)

Gardner, Paul L.

1990-01-01

Technology encompasses the goods and services which people make and provide to meet human needs, and the processes and systems used for their development and delivery. Although technology and science are related, a distinction can be made between their purposes and outcomes. This paper considers four possible approaches to teaching students about the relationship between technology and science. A technology-as-illustration approach treats technology as if it were applied science; artefacts are presented to illustrate scientific principles. A cognitive-motivational approach also treats technology as applied science, but presents technology early in the instructional sequence in order to promote student interest and understanding. In an artefact approach, learners study artefacts as systems in order to understand the scientific principles which explain their workings. Finally, a technology-as-process approach emphasises the role of technological capability; in this approach, scientific concepts do not have privileged status as a basis for selecting curriculum content.

A case history of technology transfer

NASA Technical Reports Server (NTRS)

1981-01-01

A sequence of events, occurring over the last 25 years, are described that chronicle the evolution of ion-bombardment electric propulsion technology. Emphasis is placed on the latter phases of this evolution, where special efforts were made to pave the way toward the use of this technology in operational space flight systems. These efforts consisted of a planned program to focus the technology toward its end applications and an organized process that was followed to transfer the technology from the research-technology NASA Center to the user-development NASA Center and its industry team. Major milestones in this evolution, which are described, include the development of thruster technology across a large size range, the successful completion of two space electric rocket tests, SERT I and SERT II, development of power-processing technology for electric propulsion, completion of a program to make the technology ready for flight system development, and finally the technology transfer events.

Weather Information Communication (WINCOMM) VDL-3 and 1090ES Final Test Requirements, Test Plans, and Test Results

NASA Technical Reports Server (NTRS)

Griner, James H.; Jirberg, Russ; Frantz, Brian; Kachmar, Brian A.

2006-01-01

NASA s Aviation Safety Program was created for the purpose of making a significant reduction in the incidents of weather related aviation accidents by improving situational awareness. The objectives of that program are being met in part through advances in weather sensor technology, and in part through advances in the communications technology that are developed for use in the National Airspace System. It is this latter element, i.e., the improvements in aviation communication technologies, that is the focus of the Weather Information Communications project. This report describes the final flight test results completed under the WINCOMM project at the NASA Glenn Research Center of the 1090 Extended Squitter (1090ES) and VDL Mode 3 (VDL-3) data links as a medium for weather data exchange. It presents the use of 1090ES to meet the program objectives of sending broadcast turbulence information and the use of VDL-3 to send graphical weather images. This report provides the test requirements and test plans, which led to flight tests, as well as final results from flight testing. The reports define the changes made to both avionics and ground-based receivers as well as the ground infrastructure to support implementation of the recommended architecture, with a focus on the issues associated with these changes.

Systems Integration, Analysis and Modeling Support to the HEDS Technology/Commercialization Initiative (HTCI)

NASA Technical Reports Server (NTRS)

Feingold, Harvey; ONeil, Dan (Technical Monitor)

2002-01-01

In response to a recommendation from OMB, NASA's Fiscal Year 2001 budget included a new program within the HEDS (Human Exploration and Development of Space) Enterprise called HEDS Technology/ Commercialization Initiative (HTCI). HTCI had three overarching goals: to support REDS analysis and planning for safe, affordable and effective future programs and projects that advance human exploration, scientific discovery, and the commercial development of space; to pursue research, development, and validation of breakthrough technologies and highly innovative systems concepts; and to advance die creation of strong partnerships within NASA, with U.S. industry and universities, and internationally. As part of its contracted effort, SAIC was to write a report contribution, describing die results of its task activities, to a final HTCI report prepared by MSFC. Unfortunately, government cancellation of the HTCI program in the summer of 2001 curtailed all efforts on the program including die Final HTCI report. In the absence of that report, SAIC has issued this final report in an attempt to document some of the technical material it produced. The report contains SAIC presentations for both HTCI workshops; a set of roadmap charts for the Systems Analysis, Integration and Modeling; and charts showing the evolution of the current TITAN modeling architecture.

Carbon footprint of forest and tree utilization technologies in life cycle approach

NASA Astrophysics Data System (ADS)

Polgár, András; Pécsinger, Judit

2017-04-01

In our research project a suitable method has been developed related the technological aspect of the environmental assessment of land use changes caused by climate change. We have prepared an eco-balance (environmental inventory) to the environmental effects classification in life-cycle approach in connection with the typical agricultural / forest and tree utilization technologies. The use of balances and environmental classification makes possible to compare land-use technologies and their environmental effects per common functional unit. In order to test our environmental analysis model, we carried out surveys in sample of forest stands. We set up an eco-balance of the working systems of intermediate cutting and final harvest in the stands of beech, oak, spruce, acacia, poplar and short rotation energy plantations (willow, poplar). We set up the life-cycle plan of the surveyed working systems by using the GaBi 6.0 Professional software and carried out midpoint and endpoint impact assessment. Out of the results, we applied the values of CML 2001 - Global Warming Potential (GWP 100 years) [kg CO2-Equiv.] and Eco-Indicator 99 - Human health, Climate Change [DALY]. On the basis of the values we set up a ranking of technology. By this, we received the environmental impact classification of the technologies based on carbon footprint. The working systems had the greatest impact on global warming (GWP 100 years) throughout their whole life cycle. This is explained by the amount of carbon dioxide releasing to the atmosphere resulting from the fuel of the technologies. Abiotic depletion (ADP foss) and marine aquatic ecotoxicity (MAETP) emerged also as significant impact categories. These impact categories can be explained by the share of input of fuel and lube. On the basis of the most significant environmental impact category (carbon footprint), we perform the relative life cycle contribution and ranking of each technologies. The technological life cycle stages examined in the stands are the followings: Stage 1. cleaning cutting Stage 2. selection thinning Stage 3. increment thinning Stage 4. final harvest In these priority impact categories, the life cycle contribution of technologies varied according to the life cycle stages. • The spruce stand showed the smallest contribution in the stages 1, 2, 3 alike. • After the large contribution of beech stand at the beginning (stage 1), it continues representing a moderate level in stage 2 and 3, and it shares the smallest rate in final harvest (stage 4). • The oak stand showed the largest contribution in the stages 2, 3, 4 alike. • In the case of acacia and poplar, we have got the same results as in the case of oak stands. • In the case of short rotation energy plantations (willow, poplar), we got the results typical on stage 4 of spruce stands. We can conclude, that in case of the stage of final harvest, which represents the most significant environmental impact, the ranking of working systems showes the increasing order of „energy plantations - beech - spruce - acacia - poplar - oak". The environmental assessment of technological aspects of land use and land use change represent an important added value to the climate research. Acknowledgement: This research has been supported by the Agroclimate.2 VKSZ_12-1- 2013-0034 project. Keywords: life-cycle assessment / forest utilization technology / carbon footprint / life-cycle thinking

The quest for engaging AmI: Patient engagement and experience design tools to promote effective assisted living.

PubMed

Triberti, Stefano; Barello, Serena

2016-10-01

Recent research highlights that patient engagement, conceived as a patient's behavioral, cognitive and emotional commitment to his own care management, is a key issue while implementing new technologies in the healthcare process. Indeed, eHealth interventions may systematically fail when the patient's subjective experience has not been taken into consideration since the first steps of the technology design. In the present contribution, we argue that such an issue is more and more crucial as regarded to the field of Ambient Intelligence (AmI). Specifically, the exact concept of technologies embedded in the patients' surrounding environment implies a strong impact on their everyday life, which can be perceived as a limitation to autonomy and privacy, and therefore refused or even openly opposed by the final users. The present contribution tackles this issue directly, highlighting: (1) a theoretical framework to include patient engagement in the design of AmI technologies; (2) assessment measures for patient engagement while developing and testing the effectiveness of AmI prototypes for healthcare. Finally (3) this contribution provides an overview of the main issues emerging while implementing AmI technologies and suggests specific design solutions to address them. Copyright © 2016 Elsevier Inc. All rights reserved.

Technology, Division of Labor and Alienation From Work. Final Report.

ERIC Educational Resources Information Center

Shepard, Jon M.

This study investigated the theory that a worker's relationship to technology instills in him identifiable attitudes about work. Using samples of office workers from a bank and five insurance companies, and samples of factory workers from the oil refining and automobile industries, a total of 1,888 workers were divided into (1) office and factory…

Design and Inquiry: Bases for an Accommodation between Science and Technology Education in the Curriculum?

ERIC Educational Resources Information Center

Lewis, Theodore

2006-01-01

This article examines the merits of the proposition that design and inquiry are conceptual parallels. It does so by first looking closely at the inquiry-related discourse within science education, then at aspects of the design discourse within engineering, and finally within technology education. Convergences and divergences of these two streams…

Unified Technical Concepts--Phase II. Expand Application to Industrial Technologies and Adult Education. Final Report.

ERIC Educational Resources Information Center

Technical Education Research Center, Waco, TX.

A project was conducted to develop a laboratory-based instructional system in physics for two-year technician programs that emphasizes both the analogies between basic physical principles and the applications of the principles in modern technology. The Unified Technical Concepts (UTC) system that was developed is (1) a reorganization of physics…

Introduction of Digital Computer Technology Into the Undergraduate Chemistry Laboratory. Final Technical Report.

ERIC Educational Resources Information Center

Perone, Sam P.

The objective of this project has been the development of a successful approach for the incorporation of on-line computer technology into the undergraduate chemistry laboratory. This approach assumes no prior programing, electronics or instrumental analysis experience on the part of the student; it does not displace the chemistry content with…

Advanced Crash Avoidance Technologies (ACAT) Program - Final Report of the Volvo-Ford-UMTRI Project: Safety Impact Methodology for Lane Departure Warning - Method Development and Estimation of Benefits

DOT National Transportation Integrated Search

2010-10-01

The Volvo-Ford-UMTRI project: Safety Impact Methodology (SIM) for Lane Departure Warning is part of the U.S. Department of Transportation's Advanced Crash Avoidance Technologies (ACAT) program. The project developed a basic analytical framework for e...

Flight Simulator: Use of SpaceGraph Display in an Instructor/Operator Station. Final Report.

ERIC Educational Resources Information Center

Sher, Lawrence D.

This report describes SpaceGraph, a new computer-driven display technology capable of showing space-filling images, i.e., true three dimensional displays, and discusses the advantages of this technology over flat displays for use with the instructor/operator station (IOS) of a flight simulator. Ideas resulting from 17 brainstorming sessions with…

A Model Program in Science, Mathematics, and Technology. Final Report TP87-9.

ERIC Educational Resources Information Center

McDowell, Ceasar; And Others

Over the past 5 years parents, industry leaders, and policy makers have called repeatedly for the improvement of mathematics and science education in urban schools and for measures to insure that all students are "technologically literate." Various efforts at the national, state, and local levels have emerged in response to these calls, with…

Enlargement Futures Project: Expert Panel on Technology, Knowledge and Learning. Final Report.

ERIC Educational Resources Information Center

Gourova, Elissaveta; Ducatel, Ken; Gavigan, James; Scapolo, Fabiana; Di Pietrogiacomo, Paola

The next 10 years provide an opportunity for the European Union (EU) to renew the science and technology (S&T) base and build necessary knowledge-society capacities and capabilities in Pre-Accession Countries (PACs). Applied research has faced a major downsize; redressing the balance in the research and development systems is urgently needed.…

Competency-Based Curriculum Guide for Laser Technology. September 1980-June 1981.

ERIC Educational Resources Information Center

Fioroni, John J.

This document contains materials developed by a project to provide a competency-based curriculum guide for laser technology at the community college level. An abstract of the final report is included. Next, the 17 job competencies determined as necessary to meet the job description of laser technician are listed. A career ladder and qualifications…

Development of Articulated Competency-Based Curriculum in Laser/Electro-Optics Technology. Final Report.

ERIC Educational Resources Information Center

Luzerne County Community Coll., Nanticoke, PA.

The project described in this report was conducted at the Community College of Luzerne County (Pennsylvania) to develop, in conjunction with area vocational-technical schools, the second year of a competency-based curriculum in laser/electro-optics technology. During the project, a task force of teachers from the area schools and the college…

Arsenic Removal from Drinking Water by Adsorptive Media U.S. EPA Demonstration Project at Nambe Pueblo, New Mexico - Final Performance Evaluation Report

EPA Science Inventory

This report documents the activities performed and the results obtained from this arsenic removal treatment technology demonstration project at the Nambe Pueblo, New Mexico. The main objective of the project was to evaluate the effectiveness of AdEdge Technologies' AD-33 media i...

Implementation of Advanced Health Care Technology into Existing Competency-Based Health Care Program. Final Report.

ERIC Educational Resources Information Center

Klemovage, Shirley

A project was undertaken to develop new curriculum materials that could be incorporated into an existing health assistant program to cover recent advances in health care technology. Area physicians' offices were toured and meetings were held with administrators of local hospitals in order to discover what kinds of advances in health care…

A Testbed for Advancing the Role of Digital Technologies for Library Preservation and Access. Final Report.

ERIC Educational Resources Information Center

Kenney, Anne R.; Personius, Lynne K.

In cooperation with the Commission on Preservation and Access, Xerox Corporation, Sun Microsystems, Inc., and the New York State Program for the Conservation and Preservation of Library Research Materials, Cornell University (New York) studied and established the effectiveness of digital technology to preserve and make available research library…

Integrating a Microcomputer for Agriculture Data and Telecommunications into the Agriculture Classroom. Final Report.

ERIC Educational Resources Information Center

Northeast Arkansas Educational Cooperative, Strawberry.

A program was conducted to integrate computer technology into agriculture classrooms in 25 secondary schools and 4 universities in Arkansas. State-of-the-art technology from the AgriData Network of Milwaukee was used. The AgriData Network includes the Ag Ed Network, which offers more than 800 "live textbook" lessons with current…

Summative Evaluation of the Office of Learning Technologies. Final Report

ERIC Educational Resources Information Center

Human Resources Development Canada, 2002

2002-01-01

The Office of Learning Technologies (OLT) was launched by Human Resources Canada (HRDC) in 1996 as part of an education and training strategy for adult learners. It was established with an annual budget of $6 million. As a contributions program, the OLT encourages and supports initiatives of various public and private sector partners to expand…

The Curriculum Development Project for the Medical Laboratory Technology Program at Miami-Dade Junior College, Miami, Florida. Final Report.

ERIC Educational Resources Information Center

Miami-Dade Junior Coll., FL. Div. of Allied Health Studies.

During Phase I of an Allied Health Professions Basic Improvement Grant, a five-member committee developed a curriculum for a medical laboratory technology program at Miami-Dade Junior College by: (1) defining competencies which differentiate a certified laboratory assistant from a medical laboratory technician, (2) translating expected laboratory…

Innovations: The Social Consequences of Science and Technology. Final Evaluation Report.

ERIC Educational Resources Information Center

Tolman, Richard R.

The Biological Sciences Curriculum Study designed, developed, and field-tested a series of nine curriculum resource units for a semester program called "Innovations: The Social Consequences of Science and Technology (IST)." The units were designed for use by students and teachers in the 11th and 12th grades and at the junior college…

Harvard University Program on Technology and Society 1964-1972. A Final Review.

ERIC Educational Resources Information Center

Harvard Univ., Cambridge, MA. Program on Technology and Society.

Eight years of research by the Harvard University's Program on Technology and Society are summarized. Lengthy abstracts of the 29 books and 164 articles that resulted from the Program, as well as interim accounts of projects not yet completed are presented. The report is divided into four parts; institutions (including business, education, and…

Bilingual Academic Computer and Technology Oriented Program. Project COM-TECH, 1987-1988.

ERIC Educational Resources Information Center

Berney, Tomi D.; Plotkin, Donna

The Bilingual Computer and Technology Oriented Program (COM-TECH) completed the final year of a 3-year funding cycle. The project's primary goal was to provide bilingual individualized instruction, using an enrichment approach, to Spanish- and Haitian Creole/French-speaking students of varying levels of native and English second-language (ESL)…

State-Wide Evaluation of the New Hampshire ESEA Title II, Part D Grant Program. Final Report

ERIC Educational Resources Information Center

Knestis, Kirk; Smoke-Zur, Naomi; Gibson, Rachel; Pike, Jessica Yusaitis; Higgins, Cathy

2011-01-01

The Title II-D grant program, "Enhancing Education Through Technology," (EETT) provides financial assistance to higher poverty school districts that have the greatest need for technology support or have been identified as being in need of improvement. In 2009, the American Reinvestment and Recovery Act (ARRA) provided an additional $650…

Information and Communication Technologies and Continuing Health Professional Education in Canada. A Survey of Providers Final Report.

ERIC Educational Resources Information Center

Memorial Univ., St. John's (Newfoundland).

The use of information and communication technologies (ICT) in continuing health professional education (CHPE) was examined in a national survey of Canadian CHPE providers. Of the 3,044 surveys distributed to schools of medicine, nursing, and pharmacy, national/provincial health professional associations, nonprofit health advocacy organizations,…

Arsenic Removal from Drinking Water by Adsorptive Media - U.S. EPA Demonstration Project at Geneseo Hills Subdivision, in Geneseo, IL Final Performance Evaluation Report

EPA Science Inventory

This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project at the Geneseo Hills Subdivision in Geneseo, IL. The main objective of the project was to evaluate the effectiveness of AdEdge Technologies...

Chemical Operations Technology Curriculum Development Project. PY95 Final Detailed Report.

ERIC Educational Resources Information Center

Texas State Technical Coll., Marshall.

A model curriculum for an associate of applied science degree in chemical operations technology (COT) was developed at Texas State Technical College in Marshall, Texas. First, a comprehensive analysis of the local and statewide labor market demand for trained personnel in the advanced field of COT was conducted. Next, a comprehensive task analysis…

Development of Articulated Competency-Based Curriculum in Automated Systems/Robotics Technology. Final Report.

ERIC Educational Resources Information Center

Luzerne County Community Coll., Nanticoke, PA.

The project described in this report was conducted at the Community College of Luzerne County (Pennsylvania) to develop, in conjunction with area vocational-technical schools, the second year of a competency-based curriculum in automated systems/robotics technology. During the project, a task force of teachers from the area schools and the college…

Measuring the Teaching Self-Efficacy of Science, Technology, Engineering, and Math Graduate Teaching Assistants

ERIC Educational Resources Information Center

DeChenne, Sue Ellen; Enochs, Larry

2010-01-01

An instrument to measure the teaching self-efficacy of science, technology, engineering, and mathematics (STEM) GTAs is adapted from a general college teaching instrument (Prieto Navarro, 2005) for the specific teaching environment of the STEM GTAs. The construct and content validity and reliability of the final instrument are indicated. The final…

Using a Technology-Based Case to Aid in Improving Assessment

ERIC Educational Resources Information Center

Zelin, Robert C., II

2008-01-01

This paper describes how a technology-based case using Microsoft Access can aid in the assessment process. A case was used in lieu of giving a final examination in an Accounting Information Systems course. Students worked in small groups to design a database-driven payroll system for a hypothetical company. Each group submitted its results along…

Issues Involved in Attempting to Develop Independent Learning in Pupils Working on Technological Projects

ERIC Educational Resources Information Center

Barak, Moshe

2004-01-01

This research addresses the impact of technological projects at high school on pupils' learning. The participants were sixty low-mid achieving pupils who worked for one year on final projects for matriculation exams. Data were collected through observations of laboratory lessons, interviews with pupils and teachers, and analysis of pupils'…

College Library Technology and Cooperation Grants Program, Higher Education Act, Title II-D. Final Performance Report.

ERIC Educational Resources Information Center

Hanifan, Thomas; Hoogheem, Cynthia L.

The Eastern Iowa Community College District (EICCD) libraries received a federal College Library Technology and Cooperation grant to provide and link public access catalogs at each college of the district--Clinton Community College, Muscatine Community College, and Scott Community College. That network is named Quad-LINC (Quad Cities Libraries in…

Development of Precoat Filtration Technology for Reverse Osmosis Units

DTIC Science & Technology

1981-11-20

CONTRACT DAAK 70-79-C-0046 0 FINAL REPORT 0 DEVELOPMENT OF PRECOAT FILTRATION TECHNOLOGY FOR REVERSE OSMOSIS UNITS Submitted by: ,i JOHNS - MANVILLE SALES...NTU (Hach). The one square foot vertical leaf filter was set up at the Johns - Manville R&D Center as shown in Figure 1. A 300 gallon feed tank was

Mapping Engineering Concepts for Secondary Level Education. Final Report. Research in Engineering and Technology Education

ERIC Educational Resources Information Center

Daugherty, Jenny L.

2011-01-01

Much of the national attention on science, technology, engineering, and mathematics (STEM) education tends to concentrate on science and mathematics, with its emphasis on standardized test scores. However as the National Academy of Engineering Committee on K-12 Engineering Education stressed, engineering can contribute to the development of an…

Improving Employment Outcomes among American Indians through Assistive Technology: A Preliminary Study. Final Report.

ERIC Educational Resources Information Center

Schacht, Robert M.; Gahungu, Athanase; Gallagher, Larry

This report discusses a project that compared the rate of use of assistive technology (AT) services and devices by American Indians and Alaska Natives with that of other ethnically diverse groups, identified barriers, and examined consumer satisfaction regarding AT. The project drew on four sources of data: the Rehabilitation Services…

TECHNOLOGY TRANSFER OF AN INNOVATIVE REMEDIATION TECHNOLOGY FROM THE LABORATORY TO THE FIELD: A CASE STUDY OF IN SITU AEROBIC COMETABOLIC BIOREMEDIATION. (R825689C067)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Final Report: Results from Accessing Curriculum through Technology Tools (ACTTT), A Model Development Project

ERIC Educational Resources Information Center

Johanson, Joyce; Clark, Letha; Daytner, Katrina; Robinson, Linda

2009-01-01

Accessing Curriculum through Technology Tools (ACTTT), a model development project, was developed and tested by staff of the Center for Best Practices in Early Childhood (the Center), a research and development unit within the College of Education and Human Services at Western Illinois University. The major goal of ACTTT was to develop,…

Role of research aircraft in technology development

NASA Technical Reports Server (NTRS)

Szalai, K. J.

1984-01-01

The United States's aeronautical research program has been rich in the use of research aircraft to explore new flight regimes, develop individual aeronautical concepts, and investigate new vehicle classes and configurations. This paper reviews the NASA supercritical wing, digital fly-by-wire, HiMAT, and AD-1 oblique-wing flight research programs, and draws from these examples general conclusions regarding the role and impact of research aircraft in technology development. The impact of a flight program on spinoff technology is also addressed. The secondary, serendipitous results are often highly significant. Finally, future research aircraft programs are examined for technology trends and expected results.

High Penetration Photovoltaic Power Electronics and Energy Management Technology Research, Development and Demonstration: Cooperative Research and Development Final Report, CRADA Number CRD-13-517

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hudgins, Andrew P.

Advanced Energy Industries, Inc., will partner with DOE's National Renewable Energy Laboratory (NREL) to conduct research and development to demonstrate technologies that will increase the penetration of photovoltaic (PV) technologies for commercial and utility applications. Standard PV power control systems use simple control techniques that only provide real power to the grid. A focus of this partnership is to demonstrate how state of the art control and power electronic technologies can be combined to create a utility interactive control platform.

Review of infrared scene projector technology-1993

NASA Astrophysics Data System (ADS)

Driggers, Ronald G.; Barnard, Kenneth J.; Burroughs, E. E.; Deep, Raymond G.; Williams, Owen M.

1994-07-01

The importance of testing IR imagers and missile seekers with realistic IR scenes warrants a review of the current technologies used in dynamic infrared scene projection. These technologies include resistive arrays, deformable mirror arrays, mirror membrane devices, liquid crystal light valves, laser writers, laser diode arrays, and CRTs. Other methods include frustrated total internal reflection, thermoelectric devices, galvanic cells, Bly cells, and vanadium dioxide. A description of each technology is presented along with a discussion of their relative benefits and disadvantages. The current state of each methodology is also summarized. Finally, the methods are compared and contrasted in terms of their performance parameters.

Regulating small things: genes, gametes and nanotechnology.

PubMed

Bennett, Belinda

2007-08-01

Biotechnology and nanotechnology both intersect with other technologies in ways that open new possibilities for further technological progress. The potential for increased convergence between technological fields highlights the need for regulatory frameworks to be integrated, flexible and responsive. Within a federal legal system such as Australia's, there is a need to ensure that we adopt a coordinated national approach to the crafting of regulatory solutions. In addition, there is a need for global cooperation in the development of international standards and regulatory harmonisation. Finally, this article considers the role that law plays in negotiating risk in relation to new technologies.

Printing versus coating - What will be the future production technology for printed electronics?

NASA Astrophysics Data System (ADS)

Glawe, Andrea; Eggerath, Daniel; Schäfer, Frank

2015-02-01

The market of Large Area Organic Printed Electronics is developing rapidly to increase efficiency and quality as well as to lower costs further. Applications for OPV, OLED, RFID and compact Printed Electronic systems are increasing. In order to make the final products more affordable, but at the same time highly accurate, Roll to Roll (R2R) production on flexible transparent polymer substrates is the way forward. There are numerous printing and coating technologies suitable depending on the design, the product application and the chemical process technology. Mainly the product design (size, pattern, repeatability) defines the application technology.

Social issues and implications of remote sensing applications: Paradigms of technology transfer

NASA Technical Reports Server (NTRS)

Hoos, I. R.

1980-01-01

The transfer of technology from one federal agency to another was observed in the case of the move of LANDSAT to NOAA. An array of unanticipated consequences was found that have important impacts on both the process and outcome of the transfer. When the process was studied from viewpoint of the ultimate recipient, a set of expectations and perceptions were found that figure more in a final assessment than do the attributes of the technology being transfered. The question of how to link a technology with a community of potential users was studed in detail.

Final Report on the Proposal to Provide Asian Science and Technology Information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahaner, David K.

2003-07-23

The Asian Technology Information Program (ATIP) conducted a seven-month Asian science and technology information program for the Office:of Energy Research (ER), U.S: Department of Energy (DOE.) The seven-month program consists of 1) monitoring, analyzing, and dissemiuating science and technology trends and developments associated with Asian high performance computing and communications (HPC), networking, and associated topics, 2) access to ATIP's annual series of Asian S&T reports for ER and HPC related personnel and, 3) supporting DOE and ER designated visits to Asia to study and assess Asian HPC.

Laser Technician Associate Degree Program. A Proposal Submitted to Wisconsin State Board of Vocational, Technical, and Adult Education. (Curriculum Development.) Final Report.

ERIC Educational Resources Information Center

North Central Technical Inst., Wausau, WI.

This final report contains the program proposal with supporting data for developing curriculum materials for and implementing an associate-degree laser technology program at the North Central Technical Institute. The proposal outline provides this information: (1) objectives for the program designed to prepare a technician to safely operate,…

Iowa High School High Tech: Promoting Careers in Technology for Students with Disabilities. Final Report and Implementation Manual.

ERIC Educational Resources Information Center

McQuillen, Terry; Nietupski, John; Berg, Deana Duncan; Daugherty, Vicki; Bildstein, Stephanie

This final report and implementation manual describes the activities and outcomes of Iowa's High School High Tech (HSHT) program, a joint effort of Grant Wood Area Education Agency and Goodwill Industries of Southeast Iowa to inspire students with disabilities to pursue high tech careers. The program provides opportunities for students to learn…

Joint Operations 2030 - Final Report (Operations interarmees 2030 - Rapport final)

DTIC Science & Technology

2011-04-01

case of crisis : • Technologies to support emergency management operations, inter-organisational coordination and communication , distributed...are made up of national representatives as well as generally recognised ‘world class’ scientists. They also provide a communication link to military...Other Entities H.4 Capable of Establishing and Maintaining Communication Channels and Liaison Relationships H-7 with Potential Service Providers

Implementing Energy Education in Florida's High Schools: A Two-Week Credit Institute for Teachers in North Florida. Final Report, Volume I.

ERIC Educational Resources Information Center

LaHart, David E.; Allen, Rodney F.

This is the final report of a workshop in which selected teachers from Florida public schools learned about energy technology and conservation, and teaching methodology needed to incorporate energy education into existing school curriculum. Participants were teachers of science, social studies, environmental studies, and home economics. During the…

Distributed Low Temperature Combustion: Fundamental Understanding of Combustion Regime Transitions

DTIC Science & Technology

2016-09-07

AFRL-AFOSR-UK-TR-2016-0021 Distributed Low Temperature Combustion 133024 Peter Lindstedt IMPERIAL COLLEGE OF SCIENCE TECHNOLOGY & MEDICINE Final...TYPE Final 3. DATES COVERED (From - To) 01 Feb 2013 to 31 Jul 2016 4. TITLE AND SUBTITLE Distributed Low Temperature Combustion: Fundamental...identification of five separate fluid states. 15. SUBJECT TERMS EOARD, Low Temperature Combustion, Combustion Regime Transitions 16. SECURITY

Inservice Workshops on New and Emerging Agriculture/Natural Resources Occupation Instructional Materials. Final Report, January 1, 1980-June 30, 1981.

ERIC Educational Resources Information Center

Leising, J.; Wilkins, Russell

This document contains the final report and appendixes from a project to develop resources for use by community college agricultural education instructors in better utilizing computer technology in instruction and to provide inservice workshops to make the instructors aware of available hard- and software. The four-page narrative lists objectives,…

76 FR 52937 - Ball Bearings and Parts Thereof From France, Germany, and Italy: Final Results of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-24

... programming and other errors in the margin calculations. Therefore, the final results are different from the... certain companies. We have corrected programming and other errors in the margins we included in the... Technologies GmbH; Italy--Schaeffler Italia S.r.l./WPB Water Pump Bearing GmbH & Co. KG/The Schaeffler Group...

Using Simulation Technology to Promote Social Competence of Handicapped Students. Final Report. Executive Summary.

ERIC Educational Resources Information Center

Appell, Louise S.; And Others

The purpose of this project was to design and develop simulation materials utilizing vocational situations) in mildly/moderately handicapped young adults. The final product, a set of materials titled "Social Skills on the Job," includes a videotape of 15 lessons, a computer software package, and a teacher's guide, and was marketed to a commercial…

NDE Technology Development Program for Non-Visual Volumetric Inspection Technology; Sensor Effectiveness Testing Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moran, Traci L.; Larche, Michael R.; Denslow, Kayte M.

The Pacific Northwest National Laboratory (PNNL) located in Richland, Washington, hosted and administered Sensor Effectiveness Testing that allowed four different participants to demonstrate the NDE volumetric inspection technologies that were previously demonstrated during the Technology Screening session. This document provides a Sensor Effectiveness Testing report for the final part of Phase I of a three-phase NDE Technology Development Program designed to identify and mature a system or set of non-visual volumetric NDE technologies for Hanford DST primary liner bottom inspection. Phase I of the program will baseline the performance of current or emerging non-visual volumetric NDE technologies for their abilitymore » to detect and characterize primary liner bottom flaws, and identify candidate technologies for adaptation and maturation for Phase II of the program.« less

Advanced technology for America's future in space

NASA Technical Reports Server (NTRS)

1990-01-01

In response to Recommendation 8 of the Augustine Committee Report, NASA's Office of Aeronautics, Exploration and Technology (OAET) developed a proposed 'Integrated Technology Plan for the Civil Space Program' that entails substantial changes in the processes, structure and the content of NASA's space research and technology program. The Space Systems and Technology Advisory Committee (SSTAC, a subcommittee of the NASA Advisory Committee) and several other senior, expert, informed advisory groups conducted a review of NASA's proposed Integrated Technology Plan (ITP). This review was in response to the specific request in Recommendation 8 that 'NASA utilize an expert, outside review process, managed from headquarters, to assist in the allocation of technology funds'. This document, the final report from that review, addresses: (1) summary recommendations; (2) mission needs; (3) the integrated technology plan; (4) summary reports of the technical panels; and (5) conclusions and observations.

TRICARE program; clarification of benefit coverage of durable equipment and ordering or prescribing durable equipment; clarification of benefit coverage of assistive technology devises under the Extended Care Health Option Program. Final rule.

PubMed

2014-12-31

This final rule modifies the TRICARE regulation to add a definition of assistive technology (AT) devices for purposes of benefit coverage under the TRICARE Extended Care Health Option (ECHO) Program and to amend the definitions of durable equipment (DE) and durable medical equipment (DME) to better conform the language in the regulation to the statute. The final rule amends the language that specifically limits ordering or prescribing of DME to only a physician under the Basic Program, as this amendment will allow certain other TRICARE authorized individual professional providers, acting within the scope of their licensure, to order or prescribe DME. This final rule also incorporates a policy clarification relating to luxury, deluxe, or immaterial features of equipment or devices. That is, TRICARE cannot reimburse for the luxury, deluxe, or immaterial features of equipment or devices, but can reimburse for the base or basic equipment or device that meet the beneficiary's needs. Beneficiaries may choose to pay the provider for the luxury, deluxe, or immaterial features if they desire their equipment or device to have these "extra features."

77 FR 53967 - Medicare and Medicaid Programs; Electronic Health Record Incentive Program-Stage 2

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

...This final rule specifies the Stage 2 criteria that eligible professionals (EPs), eligible hospitals, and critical access hospitals (CAHs) must meet in order to qualify for Medicare and/or Medicaid electronic health record (EHR) incentive payments. In addition, it specifies payment adjustments under Medicare for covered professional services and hospital services provided by EPs, eligible hospitals, and CAHs failing to demonstrate meaningful use of certified EHR technology (CEHRT) and other program participation requirements. This final rule revises certain Stage 1 criteria, as finalized in the July 28, 2010 final rule, as well as criteria that apply regardless of Stage.

Parental perceptions of technology and technology-focused parenting: Associations with youth screen time

PubMed Central

Sanders, Wesley; Parent, Justin; Forehand, Rex; Sullivan, Alexandra D.W.; Jones, Deborah J.

2016-01-01

In the present study we propose a model linking parental perceptions of technology to technology-related parenting strategies to youth screen time, and, finally, to internalizing and externalizing problem behaviors. Participants were 615 parents drawn from three community samples of families with children across three developmental stages: young childhood, middle childhood, and adolescence. The model was tested at each stage with the strongest support emerging in the young childhood sample. One component of parental perceptions of technology, perceived efficacy, was related to technology-related parenting strategies across developmental stages. However, the association of these strategies to child screen time and, in turn, problem behaviors, diminished as children increased in age. Implications for intervention are considered. PMID:27795603

Organizing to Implement Technology in the NASA Science Organization

NASA Technical Reports Server (NTRS)

Bauer, Robert; Pasciuto, Michael

2005-01-01

As part of a NASA reorganization to support the new Vision for Space Exploration, a number of space and Earth science activities were combined into a single organization. This merger provided an opportunity to review and revise technology development within the new entity. While this process has yet to be finalized, an overview . of some of the options and considerations is provided. Examples from one portion of the new entity, the Earth-Sun System Technology program, are used as illustrations.

Development of Micro Air Vehicle Technology With In-Flight Adaptive-Wing Structure

NASA Technical Reports Server (NTRS)

Waszak, Martin R. (Technical Monitor); Shkarayev, Sergey; Null, William; Wagner, Matthew

2004-01-01

This is a final report on the research studies, "Development of Micro Air Vehicle Technology with In-Flight Adaptrive-Wing Structure". This project involved the development of variable-camber technology to achieve efficient design of micro air vehicles. Specifically, it focused on the following topics: 1) Low Reynolds number wind tunnel testing of cambered-plate wings. 2) Theoretical performance analysis of micro air vehicles. 3) Design of a variable-camber MAV actuated by micro servos. 4) Test flights of a variable-camber MAV.

Hawaii Energy and Environmental Technologies (HEET) Initiative Phase 4

DTIC Science & Technology

2006-08-01

UNIVERSITY OF HAWAII1 AT MANOA School of Ocean and Earth Science and Technology Hawal’i Natural Energy Institute January 10, 2007 Dr. Michele L...Report: HEET Initiative: Grant N00014-04-1-0682 Enclosed you will find a copy of the Final Technical Report for the subject grant, titled Hawaii Energy and...TITLE AND SUBTITLE 5a. CONTRACT NUMBER Hawaii Energy and Environmental Technologies (HEET) Initiative Phase 4 5b. GRANT NUMBER N00014-04-1-0682 5c

DSM Science & Technology Awards (south) event 2011: the role of micronutrients in human nutrition.

PubMed

2011-10-01

On 21 June 2011, the DSM Science & Technology Awards recognized and rewarded outstanding innovative young scientists active in fundamental and applied research. As in previous years, an international judging committee honored creative and groundbreaking PhD research. Twelve finalists, the top candidates from Switzerland, Austria, France and southern Germany, were invited for the final competition followed by the award ceremony attended by numerous representatives of universities, non-governmental organizations, institutes of technology and industry. Copyright © 2011 S. Karger AG, Basel.

The Washington State Technology Plan for the K-12 Common School System. Sections 701-703, Chapter 336, Laws of 1993 (Engrossed Substitute House Bill 1209) as Amended by Chapter 245, Laws of 1994. Report to the Legislature.

ERIC Educational Resources Information Center

Washington Office of the State Superintendent of Public Instruction, Olympia.

This final report for the Washington State Technology Plan for K-12 Common Schools provides a vision, long-term framework, and recommendations for implementation. Following an executive summary and a list of committee members, the first section of the report discusses technology in K-12 schools of tomorrow, including legislative charge, vision,…

The ATLAS project: The effects of a constructionist digital laboratory project on undergraduate laboratory performance.

PubMed

Shoepe, Todd C; Cavedon, Dana K; Derian, Joseph M; Levy, Celine S; Morales, Amy

2015-01-01

Anatomical education is a dynamic field where developments in the implementation of constructive, situated-learning show promise in improving student achievement. The purpose of this study was to examine the effectiveness of an individualized, technology heavy project in promoting student performance in a combined anatomy and physiology laboratory course. Mixed-methods research was used to compare two cohorts of anatomy laboratories separated by the adoption of a new laboratory atlas project, which were defined as preceding (PRE) and following the adoption of the Anatomical Teaching and Learning Assessment Study (ATLAS; POST). The ATLAS project required the creation of a student-generated, photographic atlas via acquisition of specimen images taken with tablet technology and digital microscope cameras throughout the semester. Images were transferred to laptops, digitally labeled and photo edited weekly, and compiled into a digital book using Internet publishing freeware for final project submission. An analysis of covariance confirmed that student final examination scores were improved (P < 0.05) following the implementation of the laboratory atlas project (PRE, n = 75; POST, n = 90; means ± SE; 74.9 ± 0.9 versus 78.1 ± 0.8, respectively) after controlling for cumulative student grade point average. Analysis of questionnaires collected (n = 68) from the post group suggested students identified with atlas objectives, appreciated the comprehensive value in final examination preparation, and the constructionism involved, but recommended alterations in assignment logistics and the format of the final version. Constructionist, comprehensive term-projects utilizing student-preferred technologies could be used to improve performance toward student learning outcomes. © 2014 American Association of Anatomists.

Emerging genomic technologies and the concept of personalized medicine.

PubMed

Glinskii, Victoria G; Glinsky, Gennadi V

2008-08-01

With the completion of the Human Genome Project in May 2006, genetic testing for every American is rapidly becoming a reality. As the advanced technology fuels the path towards personalized medicine, genetic nondiscrimination legislation follows closely behind. It seems that the 2007 Genetic Information Nondiscrimination Act (GINA) will finally pass through both chambers of Congress and will be signed by the President, but questions remain. On May 1, 2008, the House passed GINA by a vote of 414 to 1. Why is this the year that genetic nondiscrimination legislation could finally become the reality? Is this the beginning of a new relationship between science and policy, where policy is finally catching up? We examine the answers to these questions through a look at the history of genetic nondiscrimination legislation and where it stands today, including arguments for and against the bill. We conclude by discussing how we can achieve a future of safe personalized medicine for the populous, which would require continuous productive interactions between policymakers and scientists.

Analysis and application of intelligence network based on FTTH

NASA Astrophysics Data System (ADS)

Feng, Xiancheng; Yun, Xiang

2008-12-01

With the continued rapid growth of Internet, new network service emerges in endless stream, especially the increase of network game, meeting TV, video on demand, etc. The bandwidth requirement increase continuously. Network technique, optical device technical development is swift and violent. FTTH supports all present and future service with enormous bandwidth, including traditional telecommunication service, traditional data service and traditional TV service, and the future digital TV and VOD. With huge bandwidth of FTTH, it wins the final solution of broadband network, becomes the final goal of development of optical access network. Firstly, it introduces the main service which FTTH supports, main analysis key technology such as FTTH system composition way, topological structure, multiplexing, optical cable and device. It focus two kinds of realization methods - PON, P2P technology. Then it proposed that the solution of FTTH can support comprehensive access (service such as broadband data, voice, video and narrowband private line). Finally, it shows the engineering application for FTTH in the district and building. It brings enormous economic benefits and social benefit.

New high-precision deep concave optical surface manufacturing capability

NASA Astrophysics Data System (ADS)

Piché, François; Maloney, Chris; VanKerkhove, Steve; Supranowicz, Chris; Dumas, Paul; Donohue, Keith

2017-10-01

This paper describes the manufacturing steps necessary to manufacture hemispherical concave aspheric mirrors for high- NA systems. The process chain is considered from generation to final figuring and includes metrology testing during the various manufacturing steps. Corning Incorporated has developed this process by taking advantage of recent advances in commercially available Satisloh and QED Technologies equipment. Results are presented on a 100 mm concave radius nearly hemispherical (NA = 0.94) fused silica sphere with a better than 5 nm RMS figure. Part interferometric metrology was obtained on a QED stitching interferometer. Final figure was made possible by the implementation of a high-NA rotational MRF mode recently developed by QED Technologies which is used at Corning Incorporated for production. We also present results from a 75 mm concave radius (NA = 0.88) Corning ULE sphere that was produced using sub-aperture tools from generation to final figuring. This part demonstrates the production chain from blank to finished optics for high-NA concave asphere.

Optics and communication technology major of physics undergraduate degree at King Mongkut's Institute of Technology Ladkrabang

NASA Astrophysics Data System (ADS)

Buranasiri, Prathan

2014-09-01

A physics undergraduate degree major in optics and communication technology has been offered at King Mongkut's Institute of Technology Ladkrabang (KMITL), Bangkok, Thailand. There are nine required three credit hour courses including two laboratory courses plus a number of selections in optics and communication based technology courses. For independent thinking and industrial working skills, nine credit hours of research project, practical training or overseas studies are included for selection in the final semester. Students are encouraged to participate in international conferences and professional organizations. Recently the program, with support from SPIE and OSA, has organized its first international conference on photonic solutions 2013 (ICPS 2013).

NASA technology utilization applications. [transfer of medical sciences

NASA Technical Reports Server (NTRS)

1973-01-01

The work is reported from September 1972 through August 1973 by the Technology Applications Group of the Science Communication Division (SCD), formerly the Biological Sciences Communication Project (BSCP) in the Department of Medical and Public Affairs of the George Washington University. The work was supportive of many aspects of the NASA Technology Utilization program but in particular those dealing with Biomedical and Technology Application Teams, Applications Engineering projects, new technology reporting and documentation and transfer activities. Of particular interest are detailed reports on the progress of various hardware projects, and suggestions and criteria for the evaluation of candidate hardware projects. Finally some observations about the future expansion of the TU program are offered.

A New Numerical Simulation technology of Multistage Fracturing in Horizontal Well

NASA Astrophysics Data System (ADS)

Cheng, Ning; Kang, Kaifeng; Li, Jianming; Liu, Tao; Ding, Kun

2017-11-01

Horizontal multi-stage fracturing is recognized the effective development technology of unconventional oil resources. Geological mechanics in the numerical simulation of hydraulic fracturing technology occupies very important position, compared with the conventional numerical simulation technology, because of considering the influence of geological mechanics. New numerical simulation of hydraulic fracturing can more effectively optimize the design of fracturing and evaluate the production after fracturing. This paper studies is based on the three-dimensional stress and rock physics parameters model, using the latest fluid-solid coupling numerical simulation technology to engrave the extension process of fracture and describes the change of stress field in fracturing process, finally predict the production situation.

[Research advances in water quality monitoring technology based on UV-Vis spectrum analysis].

PubMed

Wei, Kang-Lin; Wen, Zhi-yu; Wu, Xin; Zhang, Zhong-Wei; Zeng, Tian-Ling

2011-04-01

The application of spectral analysis to water quality monitoring is an important developing trend in the field of modern environment monitoring technology. The principle and characteristic of water quality monitoring technology based on UV-Vis spectrum analysis are briefly reviewed. And the research status and advances are introduced from two aspects, on-line monitoring and in-situ monitoring. Moreover, the existent key technical problems are put forward. Finally, the technology trends of multi-parameter water quality monitoring microsystem and microsystem networks based on microspectrometer are prospected, which has certain reference value for the research and development of environmental monitoring technology and modern scientific instrument in the authors' country.

Microbial innovations in the world of food.

PubMed

Kawasaki, Hisashi; Ueda, Kenji

2017-01-01

Technological developments in Japan based on the results of microbial research were a major pillar supporting the postwar industrial revolution. The wellspring of these advancements was the sophisticated technology used in traditional brewing, a foundation of the characteristic Japanese food culture. In this manuscript, we will describe the fermentative production of amino acids and nucleic acids following the discovery of the umami component so distinct in Japanese cuisine, which finally revealed the true power of microbial production. Thereafter, we will describe acetic acid production stemming from brewed vinegar production and the fermentative production of some other organic acids. Finally, we will delve into the massive scale of innovations achieved by the discovery of valuable micro-organisms and how they have affected the field of food.

Final priority; National Institute on Disability and Rehabilitation Research--Rehabilitation Engineering Research Centers. Final priority.

PubMed

2014-07-09

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Disability and Rehabilitation Research Projects and Centers Program administered by the National Institute on Disability and Rehabilitation Research (NIDRR). Specifically, we announce a priority for a Rehabilitation Engineering Research Center (RERC) on Improving the Accessibility, Usability, and Performance of Technology for Individuals who are Deaf or Hard of Hearing. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to focus research attention on an area of national need. We intend the priority to contribute to improving the accessibility, usability, and performance of technology for individuals who are deaf or hard of hearing.

Rapid Prototyping Technology for Manufacturing GTE Turbine Blades

NASA Astrophysics Data System (ADS)

Balyakin, A. V.; Dobryshkina, E. M.; Vdovin, R. A.; Alekseev, V. P.

2018-03-01

The conventional approach to manufacturing turbine blades by investment casting is expensive and time-consuming, as it takes a lot of time to make geometrically precise and complex wax patterns. Turbine blade manufacturing in pilot production can be sped up by accelerating the casting process while keeping the geometric precision of the final product. This paper compares the rapid prototyping method (casting the wax pattern composition into elastic silicone molds) to the conventional technology. Analysis of the size precision of blade casts shows that silicon-mold casting features sufficient geometric precision. Thus, this method for making wax patterns can be a cost-efficient solution for small-batch or pilot production of turbine blades for gas-turbine units (GTU) and gas-turbine engines (GTE). The paper demonstrates how additive technology and thermographic analysis can speed up the cooling of wax patterns in silicone molds. This is possible at an optimal temperature and solidification time, which make the process more cost-efficient while keeping the geometric quality of the final product.

Feasibility of remotely manipulated welding in space: A step in the development of novel joining technologies

NASA Technical Reports Server (NTRS)

Masubuchi, K.; Agapakis, J. E.; Debiccari, A.; Vonalt, C.

1985-01-01

A six month research program entitled Feasibility of Remotely Manipulated Welding in Space - A Step in the Development of Novel Joining Technologies is performed at the Massachusetts Institute of Technology for the Office of Space Science and Applications, NASA, under Contract No. NASW-3740. The work is performed as a part of the Innovative Utilization of the Space Station Program. The final report from M.I.T. was issued in September 1983. This paper presents a summary of the work performed under this contract. The objective of this research program is to initiate research for the development of packaged, remotely controlled welding systems for space construction and repair. The research effort includes the following tasks: (1) identification of probable joining tasks in space; (2) identification of required levels of automation in space welding tasks; (3) development of novel space welding concepts; (4) development of recommended future studies; and (5) preparation of the final report.

Big Data Technologies: New Opportunities for Diabetes Management.

PubMed

Bellazzi, Riccardo; Dagliati, Arianna; Sacchi, Lucia; Segagni, Daniele

2015-04-24

The so-called big data revolution provides substantial opportunities to diabetes management. At least 3 important directions are currently of great interest. First, the integration of different sources of information, from primary and secondary care to administrative information, may allow depicting a novel view of patient's care processes and of single patient's behaviors, taking into account the multifaceted nature of chronic care. Second, the availability of novel diabetes technologies, able to gather large amounts of real-time data, requires the implementation of distributed platforms for data analysis and decision support. Finally, the inclusion of geographical and environmental information into such complex IT systems may further increase the capability of interpreting the data gathered and extract new knowledge from them. This article reviews the main concepts and definitions related to big data, it presents some efforts in health care, and discusses the potential role of big data in diabetes care. Finally, as an example, it describes the research efforts carried on in the MOSAIC project, funded by the European Commission. © 2015 Diabetes Technology Society.

Radiation-Hardened Circuitry Using Mask-Programmable Analog Arrays. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Britton, Jr., Charles L.; Ericson, Milton Nance; Bobrek, Miljko

As the recent accident at Fukushima Daiichi so vividly demonstrated, telerobotic technologies capable of withstanding high radiation environments need to be readily available to enable operations, repair, and recovery under severe accident scenarios where human entry is extremely dangerous or not possible. Telerobotic technologies that enable remote operation in high dose rate environments have undergone revolutionary improvement over the past few decades. However, much of this technology cannot be employed in nuclear power environments due the radiation sensitivity of the electronics and the organic insulator materials currently in use. This is the final report of the activities involving the NEETmore » 2 project Radiation Hardened Circuitry Using Mask-Programmable Analog Arrays. We present a detailed functional block diagram of the proposed data acquisition system, the thought process leading to technical decisions, the implemented system, and the tested results from the systems. This system will be capable of monitoring at least three parameters of importance to nuclear reactor monitoring: temperature, radiation level, and pressure.« less

Evaluation of gasification and novel thermal processes for the treatment of municipal solid waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niessen, W.R.; Marks, C.H.; Sommerlad, R.E.

1996-08-01

This report identifies seven developers whose gasification technologies can be used to treat the organic constituents of municipal solid waste: Energy Products of Idaho; TPS Termiska Processor AB; Proler International Corporation; Thermoselect Inc.; Battelle; Pedco Incorporated; and ThermoChem, Incorporated. Their processes recover heat directly, produce a fuel product, or produce a feedstock for chemical processes. The technologies are on the brink of commercial availability. This report evaluates, for each technology, several kinds of issues. Technical considerations were material balance, energy balance, plant thermal efficiency, and effect of feedstock contaminants. Environmental considerations were the regulatory context, and such things as composition,more » mass rate, and treatability of pollutants. Business issues were related to likelihood of commercialization. Finally, cost and economic issues such as capital and operating costs, and the refuse-derived fuel preparation and energy c onversion costs, were considered. The final section of the report reviews and summarizes the information gathered during the study.« less

77 FR 13831 - Health Information Technology: Standards, Implementation Specifications, and Certification...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

...Under section 3004 of the Public Health Service Act, the Secretary of Health and Human Services is proposing to revise the initial set of standards, implementation specifications, and certification criteria adopted in an interim final rule published on January 13, 2010, and a subsequent final rule that was published on July 28, 2010, as well as to adopt new standards, implementation specifications, and certification criteria. The proposed new and revised certification criteria would establish the technical capabilities and specify the related standards and implementation specifications that Certified Electronic Health Record (EHR) Technology would need to include to, at a minimum, support the achievement of meaningful use by eligible professionals, eligible hospitals, and critical access hospitals under the Medicare and Medicaid EHR Incentive Programs beginning with the EHR reporting periods in fiscal year and calendar year 2014. This notice of proposed rulemaking also proposes revisions to the permanent certification program for health information technology, which includes changing the program's name.

Technical area status report for waste destruction and stabilization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dalton, J.D.; Harris, T.L.; DeWitt, L.M.

1993-08-01

The Office of Environmental Restoration and Waste Management (EM) was established by the Department of Energy (DOE) to direct and coordinate waste management and site remediation programs/activities throughout the DOE complex. In order to successfully achieve the goal of properly managing waste and the cleanup of the DOE sites, the EM was divided into five organizations: the Office of Planning and Resource Management (EM-10); the Office of Environmental Quality Assurance and Resource Management (EM-20); the Office of Waste Operations (EM-30); the Office of Environmental Restoration (EM-40); and the Office of Technology and Development (EM-50). The mission of the Office ofmore » Technology Development (OTD) is to develop treatment technologies for DOE`s operational and environmental restoration wastes where current treatment technologies are inadequate or not available. The Mixed Waste Integrated Program (MWIP) was created by OTD to assist in the development of treatment technologies for the DOE mixed low-level wastes (MLLW). The MWIP has established five Technical Support Groups (TSGs) whose purpose is to identify, evaluate, and develop treatment technologies within five general technical areas representing waste treatment functions from initial waste handling through generation of final waste forms. These TSGs are: (1) Front-End Waste Handling, (2) Physical/Chemical Treatment, (3) Waste Destruction and Stabilization, (4) Second-Stage Destruction and Offgas Treatment, and (5) Final Waste Forms. This report describes the functions of the Waste Destruction and Stabilization (WDS) group. Specifically, the following items are discussed: DOE waste stream identification; summary of previous efforts; summary of WDS treatment technologies; currently funded WDS activities; and recommendations for future activities.« less

Transition process from emerging NDT technology to production inspection application

NASA Astrophysics Data System (ADS)

Jappe, William; Wood, Nancy; Johnson, Maurice

1995-07-01

The successful application of emerging NDT technologies for specific aging aircraft inspections requires an integration of efforts between aircraft operators, airframe manufacturers, NDT equipment designers, and government regulators. This paper describes the development process that was followed to establish an alternate inspection technique for a DC-10 crown skin butt joint inspection. Initial investigation, intermediate development, and final evaluations are discussed.

Technology Partnership Organization: Quality Work Force Planning in East Texas. Final Report for Project Year 1990-1991.

ERIC Educational Resources Information Center

Fabac, John N.

The Technology Partnership Organization (TPO) is one of 24 Quality Work Force Planning (QWFP) entities in Texas. The TPO met its objectives through a variety of activities, including the following: (1) establishing a QWFP committee for the region; (2) providing an inventory of key regional industries with the greatest job opening potential and…

Identification of Occupational Areas for Indiana's Future. Final Report of the Technology Forecasting Task Force.

ERIC Educational Resources Information Center

Indiana State Commission on Vocational and Technical Education, Indianapolis.

A task force representing the Indiana private sector was convened for two purposes: to (1) identify the impact of technology on required worker skills, the labor market, and the vocational education, training, and employment system; and (2) identify occupational areas that should be future growth areas for the state. Task force members reviewed…

The Integration of an Information Processing Center into a Modern Office/Word Processing Technology Course. Final Report.

ERIC Educational Resources Information Center

LeVan, Jan; Arndt, Maridene

A report and related materials are provided from an activity to set up an operating information processing center that would do the work initiated by personnel in the district and to incorporate the center into the Modern Office/Word Processing Technology course. The report details objectives, population and sample, and conclusions and…

The Development of Productivity Practical Management Model at Automotive Mechanical Technology Skill Program in Semarang Vocational Schools, Indonesia

ERIC Educational Resources Information Center

Hadromi; Rachman, Maman; Soesanto; Kartana, Tri Jaka

2015-01-01

The purpose of this research is to develop automotive Mechanical Technology Skill Program (TMO) in Vocational School. The Research and Development (R&D) object was done in SMK 1, 4 and 7 Semarang, Indonesia. The result was achieved productivity Practical Management Final Model at TMO skill Program in Vocational school named momanticproter.…

76 FR 66235 - Bar Code Technologies for Drugs and Biological Products; Retrospective Review Under Executive...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-26

... costs and benefits of the rule and to identify any relevant changes in technology that have occurred... access to care; Whether the public health benefits of an action have been realized; Whether the public or... reviewing under E.O. 13563 is the Bar Code Final Rule. The Agency plans to reassess its costs and benefits...

A Junior High School Industrial Technology Curriculum Project: A Final Evaluation of the Industrial Arts Curriculum Project (IACP), 1965-1971.

ERIC Educational Resources Information Center

Buffer, James J.; And Others

The objective of the Industrial Arts Curriculum Project (IACP) was to develop, refine, and institutionalize a new and relevant 2-year junior high industrial arts program. The study focused on "industrial technology," the knowledge of management, production, and personnel practices used by men to produce goods to satisfy their needs…

A Model Secondary/Postsecondary Program to Prepare Students for Employment in High Technology Occupations. Final Report.

ERIC Educational Resources Information Center

Center for Occupational Research and Development, Inc., Waco, TX.

The Leander Independent School District in Austin, Texas, undertook a project to (1) research the training needs for high-technology occupations in the Greater Austin area, (2) develop a statewide model of an articulated 2 + 2 program to prepare students for careers as technicians, and (3) implement the articulated 2 + 2 program with Austin…

Aircraft

DTIC Science & Technology

2002-01-01

electronics, systems integration and information technology company.39 Northrop Grumman no longer seeks a position as a prime contractor/integrator of fixed...of the spares procurement and distribution processes. Finally, they recognize that excellence in Information Technology (IT) is a strategic advantage...business in export dollars, the industry has been forced to look for new markets as worldwide aircraft sales have dropped. Because the U.S. national

Centers for Professional Development and Technology (CPDT) State-Wide Evaluation Study. Final Summary Report.

ERIC Educational Resources Information Center

Macy Research Associates, Wills Point, TX.

The Texas Centers for Professional Development and Technology (CPDT) study gathered evaluative data about the progress and contribution of the centers toward their goal of systematic change in teacher preparation and student learning during four years of funding (1992-93 through 1995-96). The 21 centers in the sample included 35 universities, 15…

Establishment of the Center for Advanced Separation Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher E. Hull

2006-09-30

This Final Technical Report covers the eight sub-projects awarded in the first year and the five projects awarded in the second year of Cooperative Agreement DE-FC26-01NT41091: Establishment of the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

Multi-Modalities Sensor Science

DTIC Science & Technology

2015-02-28

enhanced multi-mode sensor science. bio -sensing, cross-discipling, multi-physics, nano-technology sailing He +46-8790 8465 1 Final Report for SOARD Project...spectroscopy, nano-technology, biophotonics and multi-physics modeling to produce adaptable bio -nanostructure enhanced multi-mode sensor science. 1...adaptable bio -nanostructure enhanced multi-mode sensor science. The accomplishments includes 1) A General Method for Designing a Radome to Enhance

Principles of Technology. Final Report, Leander Independent School District.

ERIC Educational Resources Information Center

Leander Independent School District, TX.

Principles of Technology was designed as a high school course in applied science for vocational students in the 11th and 12th grades in Leander, Texas. It consists of a 2-year curriculum covering 14 units in applied physics: (1) force; (2) work; (3) rate; (4) resistance; (5) energy; (6) power; (7) force transformers; (8) momentum; (9) waves and…

The Asian Seminar on Educational Technology (4th, Tokyo, Japan, October 10-19, 1985). Final Report.

ERIC Educational Resources Information Center

Japan Council of Educational Technology Centers, Tokyo.

This report of an international seminar which examined the utilization of advanced educational technology for the promotion of teacher education in the countries of the Asia and Pacific region is divided into six chapters: (1) an introduction providing background information, the purpose and themes of the seminar, and brief descriptions of the…

Enlargement Futures Project: Information and Communication Technologies. Final Report. Enlargement Futures Series.

ERIC Educational Resources Information Center

Gourova, Elissaveta; Burgelman, Jean-Claude; Bogdanowicz, Marc; Herrmann, Christoph

Trends in the development and utilization of information and communication technologies (ICT) in the 13 candidate countries for admission into the European Union(the CC13) were examined by a 12-member panel of experts and its staff. The analysis focused on the following topics: (1) the communication infrastructure available in the CC13; (2) issues…

Technological Improvements for Digital Fire Control Systems

DTIC Science & Technology

2017-09-30

Final Technical Status Report For DOTC-12-01-INIT061 Technological Improvements for Digital Fire Control Systems Reporting Period: 30 Sep...Initiative Information Develop and fabricate next generation designs using advanced materials and processes. This will include but is not limited to...4.2 Develop manufacturing processes 100% 4.3 Develop manufacturing processes 100% 4.4 Develop manufacturing processes 100% 5 Design Tooling

Delgado Community College/Sears-Roebuck Keeping America Working. Math, Science and Technology Summer Youth Enrichment Program. Final Report.

ERIC Educational Resources Information Center

Delgado Community Coll., New Orleans, LA.

Recognizing the need for better preparation of high school students in mathematics, science, and technology, Delgado Community College and the Orleans Parish School System entered into an agreement for the provision of a summer enrichment program for minority students in grades 7 through 9 who had exhibited average or above average abilities in…

Evaluation of the Effectiveness of the Alabama Math, Science, and Technology Initiative (AMSTI). Final Report. NCEE 2012-4008

ERIC Educational Resources Information Center

Newman, Denis; Finney, Pamela B.; Bell, Steve; Turner, Herb; Jaciw, Andrew P.; Zacamy, Jenna L.; Gould, Laura Feagans

2012-01-01

This report presents the results of an experiment conducted in Alabama beginning in the 2006/07 school year, to determine the effectiveness of the Alabama Math, Science, and Technology Initiative (AMSTI), which aims to improve mathematics and science achievement in the state's K-12 schools. This study is the first randomized controlled trial…

Materials Technology: The Common Core Skills That are Shaping the Future. Final Performance Report. January 1, 1989-June 30, 1990.

ERIC Educational Resources Information Center

Battelle Pacific Northwest Laboratories, Richland, WA.

A materials technology program was developed at Richland High School (Washington) and pilot tested at seven sites in Washington and Oregon. The program created partnerships between science and vocational education teachers at Richland High and Battelle Pacific Northwest Laboratories, and was then expanded to include other high schools, colleges,…

Landsat Technology Transfer to the Private and Public Sectors through Community Colleges and Other Locally Available Institutions, Phase II Program. Final Report.

ERIC Educational Resources Information Center

Rogers, Robert H.

In 1979, the National Aeronautics and Space Administration (NASA) and the Environmental Research Institute of Michigan (ERIM) initiated a program to investigate methods of making Landsat (satellite imagery) technology available to private sector firms through a network comprising NASA, a university or research institute, local community colleges,…

Primary Trainee Teachers' Attitudes to and Use of Computer and Technology in Mathematics: The Case of Turkey

ERIC Educational Resources Information Center

Dogan, Mustafa

2010-01-01

This study explores Turkish primary mathematics trainee teachers' attitudes to computer and technology. A survey was conducted with a self constructed questionnaire. Piloting, factor and reliability ([alpha] = 0.94) analyses were performed. The final version of the questionnaire has three parts with a total of 48 questions including a Likert type…

Spring 2006. Industry Study. Information Technology Industry

DTIC Science & Technology

2006-01-01

unclassified c . THIS PAGE unclassified Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std Z39-18 i Information Technology 2006 ABSTRACT...integration of processors, coprocessors, memory, storage, etc. into a user-programmable final product. C . Software (Apple, Oracle): These firms...able to support the U.S. national security interests. C . Manufacturing: The personal computer manufacturing industry has also changed considerably

Shaping the Future: New Expectations for Undergraduate Education in Science, Mathematics, Engineering, and Technology.

ERIC Educational Resources Information Center

National Science Foundation, Washington, DC. Directorate for Education and Human Resources.

This is the final report of an intensive review of the state of undergraduate education in science, mathematics, engineering and technology (SME&T) in America. It was conducted by a committee of the Advisory Committee to the Education and Human Resources Directorate of the National Science Foundation (NSF). The year-long review has revealed…

Effective methodology to derive strategic decisions from ESA exploration technology roadmaps

NASA Astrophysics Data System (ADS)

Cresto Aleina, Sara; Viola, Nicole; Fusaro, Roberta; Saccoccia, Giorgio

2016-09-01

Top priorities in future international space exploration missions regard the achievement of the necessary maturation of enabling technologies, thereby allowing Europe to play a role commensurate with its industrial, operational and scientific capabilities. As part of the actions derived from this commitment, ESA Technology Roadmaps for Exploration represent a powerful tool to prioritise R&D activities in technologies for space exploration and support the preparation of a consistent procurement plan for space exploration technologies in Europe. The roadmaps illustrate not only the technology procurement (to TRL-8) paths for specific missions envisaged in the present timeframe, but also the achievement for Europe of technological milestones enabling operational capabilities and building blocks, essential for current and future Exploration missions. Coordination of requirements and funding sources among all European stakeholders (ESA, EU, National, and Industry) is one of the objectives of these roadmaps, that show also possible application of the technologies beyond space exploration, both at ESA and outside. The present paper describes the activity that supports the work on-going at ESA on the elaboration and update of these roadmaps and related tools, in order to criticise the followed approach and to suggest methodologies of assessment of the Roadmaps, and to derive strategic decision for the advancement of Space Exploration in Europe. After a review of Technology Areas, Missions/Programmes and related building blocks (architectures) and operational capabilities, technology applicability analyses are presented. The aim is to identify if a specific technology is required, applicable or potentially a demonstrator in the building blocks of the proposed mission concepts. In this way, for each technology it is possible to outline one or more specific plans to increase TRL up to the required level. In practice, this translates into two possible solutions: on the one hand, approved mission concepts will be complemented with the required technologies if the latter can be considered as applicable or demo; on the other, if they are neither applicable nor demo, new missions, i.e. technology demonstrators based on multidisciplinary grouping of key technologies, shall be evaluated, so as to proceed through incremental steps. Finally, techniques to determine priorities in technology procurement are identified, and methodologies to rank the required technologies are proposed. In addition, a tool that estimates the percentage of technologies required for the final destination that are implementable in each intermediate destination of the incremental approach is presented.

A methodology for the valuation and selection of adaptable technology portfolios and its application to small and medium airports

NASA Astrophysics Data System (ADS)

Pinon, Olivia J.

The increase in the types of airspace users (large aircraft, small and regional jets, very light jets, unmanned aerial vehicles, etc.), as well as the very limited number of future new airport development projects are some of the factors that will characterize the next decades in air transportation. These factors, associated with a persistent growth in air traffic will worsen the current gridlock situation experienced at some major airports. As airports are becoming the major capacity bottleneck to continued growth in air traffic, it is therefore primordial to make the most efficient use of the current, and very often, underutilized airport infrastructure. This research thus proposes to address the increase in air traffic demand and resulting capacity issues by considering the implementation of operational concepts and technologies at underutilized airports. However, there are many challenges associated with sustaining the development of this type of airports. First, the need to synchronize evolving technologies with airports’ needs and investment capabilities is paramount. Additionally, it was observed that the evolution of secondary airports, and their needs, is tightly linked to the environment in which they operate. In particular, sensitivity of airports to changes in the dynamics of their environment is important, therefore requiring that the factors that drive the need for technology acquisition be identified and characterized. Finally, the difficulty to evaluate risk and make financially viable decisions, particularly when investing in new technologies, cannot be ignored. This research provides a methodology that addresses these challenges and ensures the sustainability of airport capacity-enhancement investments in a continuously changing environment. In particular, it is articulated around the need to provide decision makers with the capability to valuate and select adaptable technology portfolios to ensure airport financial viability. Hence, the four-step process developed in this research leverages the benefits yielded by impact assessment techniques, system dynamics modeling, and real options analysis to 1) provide the decision maker with a rigorous, structured, and traceable process for technology selection, 2) assess the combined impact of interrelated technologies, 3) support the translation of technology impact factors into airport performance indicators, and help identify the factors that drive the need for capacity expansion, and finally 4) enable the quantitative assessment of the strategic value of embedding flexibility in the formulation of technology portfolios and investment options. In particular, the development of this methodology highlights the successful implementation of relevance tree analysis, morphological analysis, filters and dependency tables to support the aforementioned process for technology selection. Further, it illustrates the limited capability of Cross Impact Analysis to identify technology relationships for the problem at hand. Finally, this methodology demonstrates, through a change in demand at the airport modeled, the importance of being able to weigh both the technological and strategic performance of the technology portfolios considered. In particular, it illustrates the impact that the level of traffic, the presence of congestion, the timing and sequence of investments, and the number of technologies included, have on the strategic value of a portfolio. Hence, by capturing the time dimension and technology causality impacts in technology portfolio selection, this work helps identify key technologies or technology groupings, and assess their performance on airport metrics. By embedding flexibility in the formulation of investment scenarios, it provides the decision maker with a more accurate picture of the options available to him, as well as the time and sequence under which these should be exercised.

Development of the PRE-HIT instrument: patient readiness to engage in health information technology.

PubMed

Koopman, Richelle J; Petroski, Gregory F; Canfield, Shannon M; Stuppy, Julie A; Mehr, David R

2014-01-28

Technology-based aids for lifestyle change are becoming more prevalent for chronic conditions. Important "digital divides" remain, as well as concerns about privacy, data security, and lack of motivation. Researchers need a way to characterize participants' readiness to use health technologies. To address this need, we created an instrument to measure patient readiness to engage with health technologies among adult patients with chronic conditions. Initial focus groups to determine domains, followed by item development and refinement, and exploratory factor analysis to determine final items and factor structure. The development sample included 200 patients with chronic conditions from 6 family medicine clinics. From 98 potential items, 53 best candidate items were examined using exploratory factor analysis. Pearson's Correlation for Test/Retest reliability at 3 months. The final instrument had 28 items that sorted into 8 factors with associated Cronbach's alpha: 1) Health Information Need (0.84), 2) Computer/Internet Experience (0.87), 3) Computer Anxiety (0.82), 4) Preferred Mode of Interaction (0.73), 5) Relationship with Doctor (0.65), 6) Cell Phone Expertise (0.75), 7) Internet Privacy (0.71), and 8) No News is Good News (0.57). Test-retest reliability for the 8 subscales ranged from (0.60 to 0.85). The Patient Readiness to Engage in Health Internet Technology (PRE-HIT) instrument has good psychometric properties and will be an aid to researchers investigating technology-based health interventions. Future work will examine predictive validity.

Development of the PRE-HIT instrument: patient readiness to engage in health information technology

PubMed Central

2014-01-01

Background Technology-based aids for lifestyle change are becoming more prevalent for chronic conditions. Important “digital divides” remain, as well as concerns about privacy, data security, and lack of motivation. Researchers need a way to characterize participants’ readiness to use health technologies. To address this need, we created an instrument to measure patient readiness to engage with health technologies among adult patients with chronic conditions. Methods Initial focus groups to determine domains, followed by item development and refinement, and exploratory factor analysis to determine final items and factor structure. The development sample included 200 patients with chronic conditions from 6 family medicine clinics. From 98 potential items, 53 best candidate items were examined using exploratory factor analysis. Pearson’s Correlation for Test/Retest reliability at 3 months. Results The final instrument had 28 items that sorted into 8 factors with associated Cronbach’s alpha: 1) Health Information Need (0.84), 2) Computer/Internet Experience (0.87), 3) Computer Anxiety (0.82), 4) Preferred Mode of Interaction (0.73), 5) Relationship with Doctor (0.65), 6) Cell Phone Expertise (0.75), 7) Internet Privacy (0.71), and 8) No News is Good News (0.57). Test-retest reliability for the 8 subscales ranged from (0.60 to 0.85). Conclusion The Patient Readiness to Engage in Health Internet Technology (PRE-HIT) instrument has good psychometric properties and will be an aid to researchers investigating technology-based health interventions. Future work will examine predictive validity. PMID:24472182

Evaluation of Future Internet Technologies for Processing and Distribution of Satellite Imagery

NASA Astrophysics Data System (ADS)

Becedas, J.; Perez, R.; Gonzalez, G.; Alvarez, J.; Garcia, F.; Maldonado, F.; Sucari, A.; Garcia, J.

2015-04-01

Satellite imagery data centres are designed to operate a defined number of satellites. For instance, difficulties when new satellites have to be incorporated in the system appear. This occurs because traditional infrastructures are neither flexible nor scalable. With the appearance of Future Internet technologies new solutions can be provided to manage large and variable amounts of data on demand. These technologies optimize resources and facilitate the appearance of new applications and services in the traditional Earth Observation (EO) market. The use of Future Internet technologies for the EO sector were validated with the GEO-Cloud experiment, part of the Fed4FIRE FP7 European project. This work presents the final results of the project, in which a constellation of satellites records the whole Earth surface on a daily basis. The satellite imagery is downloaded into a distributed network of ground stations and ingested in a cloud infrastructure, where the data is processed, stored, archived and distributed to the end users. The processing and transfer times inside the cloud, workload of the processors, automatic cataloguing and accessibility through the Internet are evaluated to validate if Future Internet technologies present advantages over traditional methods. Applicability of these technologies is evaluated to provide high added value services. Finally, the advantages of using federated testbeds to carry out large scale, industry driven experiments are analysed evaluating the feasibility of an experiment developed in the European infrastructure Fed4FIRE and its migration to a commercial cloud: SoftLayer, an IBM Company.

Bioactive Encapsulation for Military Food Applications: Request for Enhanced Nano and Micro Particle Fabrication and Characterization Facilities

DTIC Science & Technology

2016-01-25

2013 21-Jul-2014 Approved for Public Release; Distribution Unlimited Final Report: Bioactive Encapsulation for Military Food Applications: Request for...reviewed journals: Number of Papers published in non peer-reviewed journals: Final Report: Bioactive Encapsulation for Military Food Applications...Total Number: ...... Inventions (DD882) Scientific Progress Equipment was purchased. Technology Transfer 1 Bioactive Encapsulation for Military Food

Decoding the Principles of Emergence and Resiliency in Biological Collective Systems - A Multi-Scale Approach: Final Report

DTIC Science & Technology

2018-02-15

models and approaches are also valid using other invasive and non - invasive technologies. Finally, we illustrate and experimentally evaluate this...2017 Project Outline q  Pattern formation diversity in wild microbial societies q  Experimental and mathematical analysis methodology q  Skeleton...chemotaxis, nutrient degradation, and the exchange of amino acids between cells. Using both quantitative experimental methods and several theoretical

An Analysis of the Department of Defense’s Use of Other Transaction Authority (10 U.S.C. 2371)

DTIC Science & Technology

2016-06-01

and protocols and will also review the advantages / benefits , disadvantages /risks, and lessons learned with respect to OT authority. Finally, Chapter V...examined the various advantages / benefits and disadvantages /risks of OT authority. Finally, this Chapter provided a few examples of technologies that have... ADVANTAGES AND BENEFITS .........................................................44 1. Flexible Terms and Conditions

[Advanced Composites Technology Initiatives

NASA Technical Reports Server (NTRS)

Julian, Mark R.

2002-01-01

This final report closes out the W02 NASA Grant #NCC5-646. The FY02 grant for advanced technology initiatives through the Advanced Composites Technology Institute in Bridgeport, WV, at the Robert C. Byrd Institute (RCBI) Bridgeport Manufacturing Technology Center, is complete; all funding has been expended. RCBI continued to expand access to technology; develop and implement a workforce-training curriculum; improve material development; and provide prototyping and demonstrations of new and advanced composites technologies for West Virginia composites firms. The FY 02 efforts supported workforce development, technical training and the HST development effort of a super-lightweight composite carrier prototype and expanded the existing technical capabilities of the growing aerospace industry across West Virginia to provide additional support for NASA missions. Additionally, the Composites Technology and Training Center was awarded IS0 9001 - 2000 certification and Cleanroom Class 1000 certification during this report period.

[Advances in low impact development technology for urban stormwater management].

PubMed

Liu, Wen; Chen, Wei-ping; Peng, Chi

2015-06-01

Low impact development ( LID), as an innovative technology for stormwater management, is effective to mitigate urban flooding and to detain pollutants. This paper systemically introduced the LID technology system, and summarized the reduction effects of three typical LID facilities (i.e. , bio-retention, green roof and permeable pavement) on stormwater runoff and main pollutants in recent literature, as well as research outcomes and experiences of LID technology on model simulation, cost-benefit analysis and management system. On this basis, we analyzed the problems and limitations of current LID technology studies. Finally, some suggestions about future research directions, appropriate design and scientific management were put forth. This work intended to provide scientific basis and suggestions for widespread use and standard setting of LID technology in China by referencing overseas studies.

The Efficacy of Psychophysiological Measures for Implementing Adaptive Technology

NASA Technical Reports Server (NTRS)

Scerbo, Mark W.; Freeman, Frederick G.; Mikulka, Peter J.; Parasuraman, Raja; DiNocero, Francesco; Prinzel, Lawrence J., III

2001-01-01

Adaptive automation refers to technology that can change its mode of operation dynamically. Further, both the technology and the operator can initiate changes in the level or mode of automation. The present paper reviews research on adaptive technology. It is divided into three primary sections. In the first section, issues surrounding the development and implementation of adaptive automation are presented. Because physiological-based measures show much promise for implementing adaptive automation, the second section is devoted to examining candidate indices. In the final section, those techniques that show the greatest promise for adaptive automation as well as issues that still need to be resolved are discussed.

The NASA L3 Study

NASA Technical Reports Server (NTRS)

Stebbins, Robin

2016-01-01

The Astrophysics Implementation Plan calls for a minority role in L3, planned for launch in 2034. L3 The third large mission in ESAs Cosmic Visions 2015-2025 Programme NASA and ESA have been discussing a collaboration for 2 years Gravitational Observatory Advisory Team (GOAT) ESA study evaluating and recommend scientific performance tradeoffs, detection technologies, technology development activities, data analysis capabilities, schedule and cost US representatives: Guido Mueller, Mark Kasevich, Bill Klipstein, RTS Started in October 2014, concluding with a final report in late Marchor early April 2016. ESA solicited interest from ESA Member States in November 2015 NASA is continuing technology development support. ESA is restarting technology development activities.

Enhancing emergency care in low-income countries using mobile technology-based training tools.

PubMed

Edgcombe, Hilary; Paton, Chris; English, Mike

2016-12-01

In this paper, we discuss the role of mobile technology in developing training tools for health workers, with particular reference to low-income countries (LICs). The global and technological context is outlined, followed by a summary of approaches to using and evaluating mobile technology for learning in healthcare. Finally, recommendations are made for those developing and using such tools, based on current literature and the authors' involvement in the field. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Impact and promise of NASA aeropropulsion technology

NASA Technical Reports Server (NTRS)

Saunders, Neal T.; Bowditch, David N.

1990-01-01

The aeropropulsion industry in the U.S. has established an enviable record of leading the world in aeropropulsion for commercial and military aircraft. NASA's aeropropulsion program (primarily conducted through the Lewis Research Center) has significantly contributed to that success through research and technology advances and technology demonstration. Some past NASA contributions to engines in current aircraft are reviewed, and technologies emerging from current research programs for the aircraft of the 1990's are described. Finally, current program thrusts toward improving propulsion systems in the 2000's for subsonic commercial aircraft and higher speed aircraft such as the High-Speed Civil Transport and the National Aerospace Plane are discussed.

Application of BIM Technology in Prefabricated Buildings

NASA Astrophysics Data System (ADS)

Zhanglin, Guo; Si, Gao; Jun-e, Liu

2017-08-01

The development of fabricated buildings has become the main trend of the developm ent of modern construction industry in China. As the main tool of building information, BIM (b uilding information modeling) has greatly promoted the development of construction industry. Based on the review of the papers about the fabricated buildings and BIM technology in recent years, this paper analyzes the advantages of fabricated buildings and BIM technology, then exp lores the application of BIM technology in fabricated buildings. It aims to realize the rationaliz ation and scientification of project lifecycle management in fabricated construction project, and finally form a coherent information platform in the fabricated building.

The Center for Space Telemetering and Telecommunications Systems

NASA Technical Reports Server (NTRS)

Horan, S.; DeLeon, P.; Borah, D.; Lyman, R.

2003-01-01

This report comprises the final technical report for the research grant 'Center for Space Telemetering and Telecommunications Systems' sponsored by the National Aeronautics and Space Administration's Goddard Space Flight Center. The grant activities are broken down into the following technology areas: (1) Space Protocol Testing; (2) Autonomous Reconfiguration of Ground Station Receivers; (3) Satellite Cluster Communications; and (4) Bandwidth Efficient Modulation. The grant activity produced a number of technical reports and papers that were communicated to NASA as they were generated. This final report contains the final summary papers or final technical report conclusions for each of the project areas. Additionally, the grant supported students who made progress towards their degrees while working on the research.

Novel embryo selection techniques to increase embryo implantation in IVF attempts.

PubMed

Sigalos, George Α; Triantafyllidou, Olga; Vlahos, Nikos F

2016-11-01

The final success of an IVF attempt depends on several steps and decisions taken during the ovarian stimulation, the oocyte retrieval, the embryo culture and the embryo transfer. The final selection of the embryos most likely to implant is the final step in this process and the responsibility of the lab. Apart from strict morphologic criteria that historically have been used in embryo selection, additional information on genetic, metabolomic and morphokinetic characteristics of the embryo is recently combined to morphology to select the embryo most likely to produce a pregnancy. In this manuscript, we review the most recent information on the current methods used for embryo selection presenting the predictive capability of each one. A literature search was performed on Pubmed, Medline and Cochrane Database of Systematic Reviews for published studies using appropriate key words and phrases with no limits placed on time. It seems that the combination of morphologic criteria in conjunction to embryo kinetics as documented by time-lapse technology provides the most reliable information on embryo quality. Blastocyst biopsy with subsequent comprehensive chromosome analysis allows the selection of the euploid embryos with the higher implantation potential. Embryo time-lapse imaging and blastocyst biopsy combined to comprehensive chromosome analysis are the most promising technologies to increase pregnancy rates and reduce the possibility of multiple pregnancies. However, further studies will demonstrate the capability of routinely using these technologies to significantly improve IVF outcomes.

PILOT-SCALE TEST RESULTS OF A THIN FILM EVAPORATOR SYSTEM FOR MANAGEMENT OF LIQUID HIGH-LEVEL WASTES AT THE HANFORD SITE WASHINGTON USA -11364

DOE Office of Scientific and Technical Information (OSTI.GOV)

CORBETT JE; TEDESCH AR; WILSON RA

2011-02-14

A modular, transportable evaporator system, using thin film evaporative technology, is planned for deployment at the Hanford radioactive waste storage tank complex. This technology, herein referred to as a wiped film evaporator (WFE), will be located at grade level above an underground storage tank to receive pumped liquids, concentrate the liquid stream from 1.1 specific gravity to approximately 1.4 and then return the concentrated solution back into the tank. Water is removed by evaporation at an internal heated drum surface exposed to high vacuum. The condensed water stream will be shipped to the site effluent treatment facility for final disposal.more » This operation provides significant risk mitigation to failure of the aging 242-A Evaporator facility; the only operating evaporative system at Hanford maximizing waste storage. This technology is being implemented through a development and deployment project by the tank farm operating contractor, Washington River Protection Solutions (WRPS), for the Office of River Protection/Department of Energy (ORPIDOE), through Columbia Energy and Environmental Services, Inc. (Columbia Energy). The project will finalize technology maturity and install a system at one of the double-shell tank farms. This paper summarizes results of a pilot-scale test program conducted during calendar year 2010 as part of the ongoing technology maturation development scope for the WFE.« less

Different Perspectives on Technology Acceptance: The Role of Technology Type and Age

NASA Astrophysics Data System (ADS)

Arning, Katrin; Ziefle, Martina

Although eHealth technologies offer an enormous potential to improve healthcare, the knowledge about key determinants of acceptance for eHealth technology is restricted. While the underlying technology of eHealth technologies and Information and Communication technology (ICT) is quite similar, utilization contexts and using motives are quite different. In order to explore the role of technology type on acceptance, we contrasted central application characteristics of both technology types using the scenario technique. A questionnaire was administered (n = 104) measuring individual variables (age, gender) and attitudes regarding an eHealth application (blood sugar meter) in contrast to an ICT device (Personal Digital Assistant, PDA). Older users basically approved the utilization of health-related technologies and perceived lower usability barriers. In addition, we identified main utilization motives of eHealth technology and technology-specific acceptance patterns, especially regarding issues of data safety in the eHealth context. Effects of age and gender in acceptance ratings suggest a differential perspective on eHealth acceptance. Finally, practical interventions were derived in order to support eHealth device design and to promote acceptance of eHealth technology.

Oil in Ice Project Final Report

DTIC Science & Technology

2018-03-01

describes the various field technology demonstrations and provides an appendix with a description of 11 tactics using the most promising response...This report describes the various field technology demonstrations and provides an appendix with a description of 11 tactics using the most promising...water. RDC developed and evaluated two prototype temporary storage containers that could be mounted on the deck of a WLB. The tie-down method still

Mathematics: A Powerful Pre- and Post-Admission Variable to Predict Success in Engineering Programmes at a University of Technology

ERIC Educational Resources Information Center

van Wyk, Barend; Hofman, Wiecher; Louw, Cecilia

2013-01-01

Although student attrition and retention are researched all over the world, there is no final formula available to ensure academic success for selected students. The purpose is to share research undertaken at the Tshwane University of Technology (TUT) in order to investigate the role of mathematics in student achievement and retention in National…

The Development and Diffusion of the Training and Technology Program: A Decade of Development of Manpower Training, 1965-1975. Final Report.

ERIC Educational Resources Information Center

Demik, Gary H.; And Others

The report describes the development of a model training program, Training and Technology, and subsequent efforts to diffuse the innovation. Before the inception of TAT, a survey study, Resources for Southern Manpower Development, had indicated that the South had considerable manpower development potential and need. TAT was organized by Oak Ridge…

A conceptual framework for evaluating variable speed generator options for wind energy applications

NASA Technical Reports Server (NTRS)

Reddoch, T. W.; Lipo, T. A.; Hinrichsen, E. N.; Hudson, T. L.; Thomas, R. J.

1995-01-01

Interest in variable speed generating technology has accelerated as greater emphasis on overall efficiency and superior dynamic and control properties in wind-electric generating systems are sought. This paper reviews variable speed technology options providing advantages and disadvantages of each. Furthermore, the dynamic properties of variable speed systems are contrasted with synchronous operation. Finally, control properties of variable speed systems are examined.

The Effectiveness of Educational Technology Applications for Enhancing Reading Achievement in K-12 Classrooms: A Meta-Analysis. Educator's Summary. Revised

ERIC Educational Resources Information Center

Center for Research and Reform in Education, 2012

2012-01-01

This review examines research on the effects of technology use on reading achievement in K-12 classrooms. It applies consistent inclusion standards to focus on studies that met high methodological standards. A total of 84 qualified studies based on over 60,000 K-12 participants were included in the final analysis. Four major categories of…

Laser Shot Peening Final Report CRADA No. TC-02059-03

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stuart, B. C.; Hackel, L.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Metal Improvement Company, Inc. (MIC), to further develop the laser shot peening technology. This project had an emphasis on laser development and government and military applications including DOE’s natural gas and oil technology program (NGOTP), Yucca Mountain Project (YMP), F-22 Fighter, etc.

International Annual Conference (29th) of ICT Held in Karlsruhe, Federal Republic of Germany on June 30-July 3, 1998. Energetic Materials; Production, Processing and Characterization

DTIC Science & Technology

1998-06-26

The Final Proceedings for 29th International Annual Conference of ICT, 30 June 1998 - 3 July 1998. This is an interdisciplinary conference. Topics...include: (1) Components; (2) Particle Technology; (3) Synthesis, Production and Processing; (4) Characterization of Energetic Materials; (5) Safety Technology; and (6) Quality Assurance and Environmental Aspects.

Evaluating the Effectiveness of a Technology-Based Preschool Literacy Project: A Final Report of the LitTECH Outreach Project

ERIC Educational Resources Information Center

Johanson, Joyce; Bell, Carol; Daytner, Katrina

2008-01-01

Funded by the U.S. Department of Education's Office of Special Education Programs (OSEP), LitTECH Outreach was a 3-year technology-based preschool literacy project conducted by staff at the Center for Best Practices in Early Childhood, a research and development division of the College of Education and Human Services at Western Illinois…

Multi-Core Processors: An Enabling Technology for Embedded Distributed Model-Based Control (Postprint)

DTIC Science & Technology

2008-07-01

generation of process partitioning, a thread pipelining becomes possible. In this paper we briefly summarize the requirements and trends for FADEC based... FADEC environment, presenting a hypothetical realization of an example application. Finally we discuss the application of Time-Triggered...based control applications of the future. 15. SUBJECT TERMS Gas turbine, FADEC , Multi-core processing technology, disturbed based control

Use of Educational Technology in Agricultural Education: A National Study. Project Final Report Submitted to the National FFA Board of Directors.

ERIC Educational Resources Information Center

Birkenholz, Robert J.; And Others

A study was conducted to assess the extent to which instructional technology has been adopted in secondary programs of agricultural education in the United States. Teachers from 479 secondary agriculture programs were randomly selected to provide responses to a mailed survey instrument requesting information about types and quantity of equipment,…

Prospective technologies for using biohydrogen in power installations on the basis of fuel cells (a review)

NASA Astrophysics Data System (ADS)

Dunikov, D. O.; Borzenko, V. I.; Malyshenko, S. P.; Blinov, D. V.; Kazakov, A. N.

2013-03-01

The present state of technology for obtaining hydrogen by biological methods and for purifying it is reviewed from the viewpoint of its possible use in kilowatt-class power installations. Hybrid membranesorption biohydrogen purification methods combining membrane-based pretreatment and sorption-based final treatment, also with the use of metal hydrides, should be regarded as the most efficient ones.

Strategic avionics technology definition studies. Subtask 3-1A: Electrical Actuation (ELA) systems

NASA Technical Reports Server (NTRS)

Lum, Ben T. F.; Pond, Charles; Dermott, William

1993-01-01

This interim report presents the preliminary results of an electrical actuation (ELA) system study (subtask TA3-1A) to support the NASA strategic avionics technology definition studies. The final report of this ELA study is scheduled for September 30, 1993. The topics are presented in viewgraph form and include the following ELA technology demonstration testing; ELA system baseline; power and energy requirements for shuttle effector systems; power efficiency and losses of ELA effector systems; and power and energy requirements for ELA power sources.

Retinal Implants for Blind Patients

NASA Astrophysics Data System (ADS)

Rothermel, Albrecht

Recently, very promising results have been obtained in clinical trials with eye-prostheses for the blind. There is a chance that advances in surgical techniques, microelectronics design, and material science may lead to the first really useful applications of retinal implants in the near future. This chapter will focus on the actual status of subretinal surgery and implant technologies. Opportunities and limitations of the different technologies will be discussed in terms of patients benefit and technological challenges. Finally, a vision on how the devices may work and look like in the future will be given.

Future NASA Power Technologies for Space and Aero Propulsion Applications

NASA Technical Reports Server (NTRS)

Soeder, James F.

2015-01-01

To achieve the ambitious goals that NASA has outlined for the next decades considerable development of power technology will be necessary. This presentation outlines the development objectives for both space and aero applications. It further looks at the various power technologies that support these objectives and examines drivers that will be a driving force for future development. Finally, the presentation examines what type of non-traditional learning areas should be emphasized in student curriculum so that the engineering needs of the third decade of the 21st Century are met.

Integrating technology readiness into the expectation-confirmation model: an empirical study of mobile services.

PubMed

Chen, Shih-Chih; Liu, Ming-Ling; Lin, Chieh-Peng

2013-08-01

The aim of this study was to integrate technology readiness into the expectation-confirmation model (ECM) for explaining individuals' continuance of mobile data service usage. After reviewing the ECM and technology readiness, an integrated model was demonstrated via empirical data. Compared with the original ECM, the findings of this study show that the integrated model may offer an ameliorated way to clarify what factors and how they influence the continuous intention toward mobile services. Finally, the major findings are summarized, and future research directions are suggested.

Design definition study of a NASA/Navy lift/cruise fan technology V/STOL airplane: Risk assessment addendum to the final report

NASA Technical Reports Server (NTRS)

Zabinsky, J. M.; Burnham, R. W.; Flora, C. C.; Gotlieb, P.; Grande, D. L.; Gunnarson, D. W.; Howard, W. M.; Hunt, D.; Jakubowski, G. W.; Johnson, P. E.

1975-01-01

An assessment of risk, in terms of delivery delays, cost overrun, and performance achievement, associated with the V/STOL technology airplane is presented. The risk is discussed in terms of weight, structure, aerodynamics, propulsion, mechanical drive, and flight controls. The analysis ensures that risks associated with the design and development of the airplane will be eliminated in the course of the program and a useful technology airplane that meets the predicted cost, schedule, and performance can be produced.

Advanced Technologies for Heterodyne Radio Astronomy Instrumentation - Part1 By A. Pavolotsky, and Advanced Technologies for Heterodyne Radio Astronomy Instrumentation - Part2 By V. Desmaris

NASA Astrophysics Data System (ADS)

Desmaris, Vincent

2018-01-01

We present the advanced micro/nano technological engineering at the atomic level producing state-of-the-art epitaxial NbN thin-films on GaN buffer layers. Furthermore, we report the outstanding performance of the hot electron bolometers fabricated on epitaxial NbN thin films on GaN buffer layers. Finally we present advanced passive devices such as waveguide hybrids, IF hybrids and combiners for the realization of heterodyne THz receivers.

Control technology appendices for pollution control technical manuals. Final report, June 1982-February 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-04-01

The document is one of six technical handbooks prepared by EPA to help government officials granting permits to build synfuels facilities, synfuels process developers, and other interested parties. They provide technical data on waste streams from synfuels facilities and technologies capable of controlling them. Process technologies covered in the manuals include coal gasification, coal liquefaction by direct and idirect processing, and the extraction of oil from shale. The manuals offer no regulatory guidance, allowing the industry flexibility in deciding how best to comply with environmental regulations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glawe, Andrea; Eggerath, Daniel; Schäfer, Frank

The market of Large Area Organic Printed Electronics is developing rapidly to increase efficiency and quality as well as to lower costs further. Applications for OPV, OLED, RFID and compact Printed Electronic systems are increasing. In order to make the final products more affordable, but at the same time highly accurate, Roll to Roll (R2R) production on flexible transparent polymer substrates is the way forward. There are numerous printing and coating technologies suitable depending on the design, the product application and the chemical process technology. Mainly the product design (size, pattern, repeatability) defines the application technology.

Space shuttle avionics system

NASA Technical Reports Server (NTRS)

Hanaway, John F.; Moorehead, Robert W.

1989-01-01

The Space Shuttle avionics system, which was conceived in the early 1970's and became operational in the 1980's represents a significant advancement of avionics system technology in the areas of systems and redundacy management, digital data base technology, flight software, flight control integration, digital fly-by-wire technology, crew display interface, and operational concepts. The origins and the evolution of the system are traced; the requirements, the constraints, and other factors which led to the final configuration are outlined; and the functional operation of the system is described. An overall system block diagram is included.

Pervasive access to images and data--the use of computing grids and mobile/wireless devices across healthcare enterprises.

PubMed

Pohjonen, Hanna; Ross, Peeter; Blickman, Johan G; Kamman, Richard

2007-01-01

Emerging technologies are transforming the workflows in healthcare enterprises. Computing grids and handheld mobile/wireless devices are providing clinicians with enterprise-wide access to all patient data and analysis tools on a pervasive basis. In this paper, emerging technologies are presented that provide computing grids and streaming-based access to image and data management functions, and system architectures that enable pervasive computing on a cost-effective basis. Finally, the implications of such technologies are investigated regarding the positive impacts on clinical workflows.

Compiling for Application Specific Computational Acceleration in Reconfigurable Architectures Final Report CRADA No. TSB-2033-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Supinski, B.; Caliga, D.

2017-09-28

The primary objective of this project was to develop memory optimization technology to efficiently deliver data to, and distribute data within, the SRC-6's Field Programmable Gate Array- ("FPGA") based Multi-Adaptive Processors (MAPs). The hardware/software approach was to explore efficient MAP configurations and generate the compiler technology to exploit those configurations. This memory accessing technology represents an important step towards making reconfigurable symmetric multi-processor (SMP) architectures that will be a costeffective solution for large-scale scientific computing.

Advance of Hazardous Operation Robot and its Application in Special Equipment Accident Rescue

NASA Astrophysics Data System (ADS)

Zeng, Qin-Da; Zhou, Wei; Zheng, Geng-Feng

A survey of hazardous operation robot is given out in this article. Firstly, the latest researches such as nuclear industry robot, fire-fighting robot and explosive-handling robot are shown. Secondly, existing key technologies and their shortcomings are summarized, including moving mechanism, control system, perceptive technology and power technology. Thirdly, the trend of hazardous operation robot is predicted according to current situation. Finally, characteristics and hazards of special equipment accident, as well as feasibility of hazardous operation robot in the area of special equipment accident rescue are analyzed.