Controllability Analysis for Multirotor Helicopter Rotor Degradation and Failure

NASA Astrophysics Data System (ADS)

Du, Guang-Xun; Quan, Quan; Yang, Binxian; Cai, Kai-Yuan

2015-05-01

This paper considers the controllability analysis problem for a class of multirotor systems subject to rotor failure/wear. It is shown that classical controllability theories of linear systems are not sufficient to test the controllability of the considered multirotors. Owing to this, an easy-to-use measurement index is introduced to assess the available control authority. Based on it, a new necessary and sufficient condition for the controllability of multirotors is derived. Furthermore, a controllability test procedure is approached. The proposed controllability test method is applied to a class of hexacopters with different rotor configurations and different rotor efficiency parameters to show its effectiveness. The analysis results show that hexacopters with different rotor configurations have different fault-tolerant capabilities. It is therefore necessary to test the controllability of the multirotors before any fault-tolerant control strategies are employed.

Cost-effectiveness analysis of EGFR mutation testing in patients with non-small cell lung cancer (NSCLC) with gefitinib or carboplatin-paclitaxel.

PubMed

Arrieta, Oscar; Anaya, Pablo; Morales-Oyarvide, Vicente; Ramírez-Tirado, Laura Alejandra; Polanco, Ana C

2016-09-01

Assess the cost-effectiveness of an EGFR-mutation testing strategy for advanced NSCLC in first-line therapy with either gefitinib or carboplatin-paclitaxel in Mexican institutions. Cost-effectiveness analysis using a discrete event simulation (DES) model to simulate two therapeutic strategies in patients with advanced NSCLC. Strategy one included patients tested for EGFR-mutation and therapy given accordingly. Strategy two included chemotherapy for all patients without testing. All results are presented in 2014 US dollars. The analysis was made with data from the Mexican frequency of EGFR-mutation. A univariate sensitivity analysis was conducted on EGFR prevalence. Progression-free survival (PFS) transition probabilities were estimated on data from the IPASS and simulated with a Weibull distribution, run with parallel trials to calculate a probabilistic sensitivity analysis. PFS of patients in the testing strategy was 6.76 months (95 % CI 6.10-7.44) vs 5.85 months (95 % CI 5.43-6.29) in the non-testing group. The one-way sensitivity analysis showed that PFS has a direct relationship with EGFR-mutation prevalence, while the ICER and testing cost have an inverse relationship with EGFR-mutation prevalence. The probabilistic sensitivity analysis showed that all iterations had incremental costs and incremental PFS for strategy 1 in comparison with strategy 2. There is a direct relationship between the ICER and the cost of EGFR testing, with an inverse relationship with the prevalence of EGFR-mutation. When prevalence is >10 % ICER remains constant. This study could impact Mexican and Latin American health policies regarding mutation detection testing and treatment for advanced NSCLC.

Fabrication and test of inorganic/organic separators. [for silver zinc batteries

NASA Technical Reports Server (NTRS)

Smatko, J. S.

1974-01-01

Completion of testing and failure analysis of MDC 40 Ahr silver zinc cells containing largely inorganic separators was accomplished. The results showed that the wet stand and cycle life objectives of the silver zinc cell development program were accomplished. Building, testing and failure analysis of two plate cells employing three optimum separators selected on the basis of extensive screening tests, was performed. The best separator material as a result of these tests was doped calcium zirconate.

TSP Symposium 2013 Proceedings

DTIC Science & Technology

2014-01-01

test and Post - test Results of the Experimental Group Our results show that the experimental group improved on the post - test compared...4.3.4 Design of the Learning Strategy 27 4.4 Results 28 4.4.1 Post - test 28 4.4.2 Analysis of the Results 28 4.4.3 Analysis of the Results from the...Estimation Accuracy) 17 Figure 5: Methodology for the Research 24 Figure 6: Question 1, Time Control for Post - test 28 Figure 7:

Clinical usefulness of the clock drawing test applying rasch analysis in predicting of cognitive impairment.

PubMed

Yoo, Doo Han; Lee, Jae Shin

2016-07-01

[Purpose] This study examined the clinical usefulness of the clock drawing test applying Rasch analysis for predicting the level of cognitive impairment. [Subjects and Methods] A total of 187 stroke patients with cognitive impairment were enrolled in this study. The 187 patients were evaluated by the clock drawing test developed through Rasch analysis along with the mini-mental state examination of cognitive evaluation tool. An analysis of the variance was performed to examine the significance of the mini-mental state examination and the clock drawing test according to the general characteristics of the subjects. Receiver operating characteristic analysis was performed to determine the cutoff point for cognitive impairment and to calculate the sensitivity and specificity values. [Results] The results of comparison of the clock drawing test with the mini-mental state showed significant differences in according to gender, age, education, and affected side. A total CDT of 10.5, which was selected as the cutoff point to identify cognitive impairement, showed a sensitivity, specificity, Youden index, positive predictive, and negative predicive values of 86.4%, 91.5%, 0.8, 95%, and 88.2%. [Conclusion] The clock drawing test is believed to be useful in assessments and interventions based on its excellent ability to identify cognitive disorders.

[Optimization of cluster analysis based on drug resistance profiles of MRSA isolates].

PubMed

Tani, Hiroya; Kishi, Takahiko; Gotoh, Minehiro; Yamagishi, Yuka; Mikamo, Hiroshige

2015-12-01

We examined 402 methicillin-resistant Staphylococcus aureus (MRSA) strains isolated from clinical specimens in our hospital between November 19, 2010 and December 27, 2011 to evaluate the similarity between cluster analysis of drug susceptibility tests and pulsed-field gel electrophoresis (PFGE). The results showed that the 402 strains tested were classified into 27 PFGE patterns (151 subtypes of patterns). Cluster analyses of drug susceptibility tests with the cut-off distance yielding a similar classification capability showed favorable results--when the MIC method was used, and minimum inhibitory concentration (MIC) values were used directly in the method, the level of agreement with PFGE was 74.2% when 15 drugs were tested. The Unweighted Pair Group Method with Arithmetic mean (UPGMA) method was effective when the cut-off distance was 16. Using the SIR method in which susceptible (S), intermediate (I), and resistant (R) were coded as 0, 2, and 3, respectively, according to the Clinical and Laboratory Standards Institute (CLSI) criteria, the level of agreement with PFGE was 75.9% when the number of drugs tested was 17, the method used for clustering was the UPGMA, and the cut-off distance was 3.6. In addition, to assess the reproducibility of the results, 10 strains were randomly sampled from the overall test and subjected to cluster analysis. This was repeated 100 times under the same conditions. The results indicated good reproducibility of the results, with the level of agreement with PFGE showing a mean of 82.0%, standard deviation of 12.1%, and mode of 90.0% for the MIC method and a mean of 80.0%, standard deviation of 13.4%, and mode of 90.0% for the SIR method. In summary, cluster analysis for drug susceptibility tests is useful for the epidemiological analysis of MRSA.

Substantiation Data for Advanced Beaded and Tubular Structural Panels. Volume 3: Testing

NASA Technical Reports Server (NTRS)

Hedges, P. C.; Greene, B. E.

1974-01-01

The test program is described, which was conducted to provide the necessary experimental data to verify the design and analysis methods developed for beaded and tubular panels. Test results are summarized and presented for all local buckling and full size panel tests. Selected representative test data from each of these tests is presented in detail. The results of this program established a valid analysis and design procedure for circular tube panels. Test results from three other configurations show deformational modes which are not adequately accounted for in the present analyses.

Meta-analysis of gene-level tests for rare variant association.

PubMed

Liu, Dajiang J; Peloso, Gina M; Zhan, Xiaowei; Holmen, Oddgeir L; Zawistowski, Matthew; Feng, Shuang; Nikpay, Majid; Auer, Paul L; Goel, Anuj; Zhang, He; Peters, Ulrike; Farrall, Martin; Orho-Melander, Marju; Kooperberg, Charles; McPherson, Ruth; Watkins, Hugh; Willer, Cristen J; Hveem, Kristian; Melander, Olle; Kathiresan, Sekar; Abecasis, Gonçalo R

2014-02-01

The majority of reported complex disease associations for common genetic variants have been identified through meta-analysis, a powerful approach that enables the use of large sample sizes while protecting against common artifacts due to population structure and repeated small-sample analyses sharing individual-level data. As the focus of genetic association studies shifts to rare variants, genes and other functional units are becoming the focus of analysis. Here we propose and evaluate new approaches for performing meta-analysis of rare variant association tests, including burden tests, weighted burden tests, variable-threshold tests and tests that allow variants with opposite effects to be grouped together. We show that our approach retains useful features from single-variant meta-analysis approaches and demonstrate its use in a study of blood lipid levels in ∼18,500 individuals genotyped with exome arrays.

Analytical and experimental investigation of fatigue in a sheet specimen with an interference-fit bolt

NASA Technical Reports Server (NTRS)

Crews, J. H., Jr.

1975-01-01

A fatigue analysis, based on finite-element calculations and fatigue tests, was conducted for an aluminum-alloy sheet specimen with a steel interference-fit bolt. The stress analysis of the region near the bolt hole showed that the beneficial effect of an interference-fit bolt can be interpreted as the combined result of two effects: (1) load transfer through the bolt and (2) the compressive interference stresses in the sheet. Results of the fatigue tests show that progressively higher interference levels produced longer fatigue lives. The tests also show that a high level of interference prevents fretting at the bolt-sheet interface and that interferences larger than this level produced little additional improvement in fatigue life.

Factors predicting early postpartum glucose intolerance in Japanese women with gestational diabetes mellitus: decision-curve analysis.

PubMed

Kondo, M; Nagao, Y; Mahbub, M H; Tanabe, T; Tanizawa, Y

2018-04-29

To identify factors predicting early postpartum glucose intolerance in Japanese women with gestational diabetes mellitus, using decision-curve analysis. A retrospective cohort study was performed. The participants were 123 Japanese women with gestational diabetes who underwent 75-g oral glucose tolerance tests at 8-12 weeks after delivery. They were divided into a glucose intolerance and a normal glucose tolerance group based on postpartum oral glucose tolerance test results. Analysis of the pregnancy oral glucose tolerance test results showed predictive factors for postpartum glucose intolerance. We also evaluated the clinical usefulness of the prediction model based on decision-curve analysis. Of 123 women, 78 (63.4%) had normoglycaemia and 45 (36.6%) had glucose intolerance. Multivariable logistic regression analysis showed insulinogenic index/fasting immunoreactive insulin and summation of glucose levels, assessed during pregnancy oral glucose tolerance tests (total glucose), to be independent risk factors for postpartum glucose intolerance. Evaluating the regression models, the best discrimination (area under the curve 0.725) was obtained using the basic model (i.e. age, family history of diabetes, BMI ≥25 kg/m 2 and use of insulin during pregnancy) plus insulinogenic index/fasting immunoreactive insulin <1.1. Decision-curve analysis showed that combining insulinogenic index/fasting immunoreactive insulin <1.1 with basic clinical information resulted in superior net benefits for prediction of postpartum glucose intolerance. Insulinogenic index/fasting immunoreactive insulin calculated using oral glucose tolerance test results during pregnancy is potentially useful for predicting early postpartum glucose intolerance in Japanese women with gestational diabetes. © 2018 Diabetes UK.

Investigating the correlation between wastewater analysis and roadside drug testing in South Australia.

PubMed

Bade, Richard; Tscharke, Benjamin J; Longo, Marie; Cooke, Richard; White, Jason M; Gerber, Cobus

2018-06-01

The societal impact of drug use is well known. An example is when drug-intoxicated drivers increase the burden on policing and healthcare services. This work presents the correlation of wastewater analysis (using UHPLC-MS/MS) and positive roadside drug testing results for methamphetamine, 3,4-methylenedioxymethamphetamine (MDMA) and cannabis from December 2011-December 2016 in South Australia. Methamphetamine and MDMA showed similar trends between the data sources with matching increases and decreases, respectively. Cannabis was relatively steady based on wastewater analysis, but the roadside drug testing data started to diverge in the final part of the measurement period. The ability to triangulate data as shown here validates both wastewater analysis and roadside drug testing. This suggests that changes in overall population drug use revealed by WWA is consistent and proportional with changes in drug-driving behaviours. The results show that, at higher levels of drug use as measured by wastewater analysis, there is an increase in drug driving in the community and therefore more strain on health services and police. Copyright © 2018 Elsevier B.V. All rights reserved.

Modified visual field trend analysis.

PubMed

De Moraes, Carlos Gustavo V; Ritch, Robert; Tello, Celso; Liebmann, Jeffrey M

2011-01-01

Visual field trend analysis can be influenced by outlying values that may disproportionately affect estimation of the rate of change. We tested a modified approach to visual field trend analysis to minimize this problem. Automated pointwise linear regression (PLR) was used in glaucoma patients with ≥13 SITA-Standard 24-2 VF tests in either eye. In the control group (Group A), conventional PLR using the entire set of VF tests was carried out. In the other 3 groups (study groups), a truncated analysis was done using only the first and last 3 (Group B), first and last 4 (Group C), or first and last 5 (Group D) VF tests. We compared the global slopes (dB/y), number of eyes experiencing significant progression, and significant improvement between groups. Ninety eyes of 90 patients were evaluated. The mean number±SD of VF tests was 15.7±2.6, spanning 7.8±1.7 years. The study groups showed similar global rates of VF change as the control group (Group A=-0.48±0.5, Group B=-0.48±0.6, Group C=-0.48±0.6, Group D=-0.48±0.5 dB/y, P>0.05), and a similar number of eyes reaching a progression endpoint (Group A=53, Group B=52, Group C=49, Group D=53, P>0.05). However, Group B showed fewer eyes presenting VF improvement (false-positives). The modified VF trend-analysis showed greater specificity than conventional PLR in a population with glaucoma.

Metrics for Analyzing Quantifiable Differentiation of Designs with Varying Integrity for Hardware Assurance

DTIC Science & Technology

2017-03-01

proposed. Expected profiles can incorporate a level of overdesign. Finally, the Design Integrity measuring techniques are applied to five Test Article ...Inserted into Test System Table 2 presents the results of the analysis applied to each of the test article designs. Each of the domains are...the lowest integrities. Based on the analysis, the DI metric shows measurable differentiation between all five Test Article Error Location Error

Solar energy storage via liquid filled cans - Test data and analysis

NASA Technical Reports Server (NTRS)

Saha, H.

1978-01-01

This paper describes the design of a solar thermal storage test facility with water-filled metal cans as heat storage medium and also presents some preliminary tests results and analysis. This combination of solid and liquid mediums shows unique heat transfer and heat contents characteristics and will be well suited for use with solar air systems for space and hot water heating. The trends of the test results acquired thus far are representative of the test bed characteristics while operating in the various modes.

Nickel-Hydrogen Cell Testing Experience, NASA/Goddard Space Flight Center

NASA Technical Reports Server (NTRS)

Rao, Gopalakrishna M.

1999-01-01

The objectives of the project were to test the Nickel-Hydrogen Cell to: (1) verify the Aerospace Cell Flight Worthiness, (2) Elucidate the Aerospace Cell Thermal Behavior, (3) Develop the Aerospace Battery Assembly Design(s) and In-orbit Battery Management plan(s) and (4) Understand the Aerospace Cell Failure Mechanism. The tests included the LEO and GEO Life cycle tests, Calorimetric Analysis, Destructive Physical analysis, and special tests. Charts show the Mission Profile Cycling Data, Stress Cycling Data. The test data complies with the mission requirements, validating the flight worthiness of batteries. The nominal stress and mission profile cycling performance test shows the charge voltage as high as 1.60V and recharge ratio greater than 1.05. It is apparent that the electrochemical signatures alone do not provide conclusive proof for Nickel precharge. The researchers recommend a gas and positive plate analyses for further confirmation.

Microparticles of Aloe vera/vitamin E/chitosan: microscopic, a nuclear imaging and an in vivo test analysis for burn treatment.

PubMed

Pereira, Gabriela Garrastazu; Santos-Oliveira, Ralph; Albernaz, Martha S; Canema, Daniel; Weismüller, Gilberto; Barros, Eduardo Bede; Magalhães, Luciana; Lima-Ribeiro, Maria Helena Madruga; Pohlmann, Adriana Raffin; Guterres, Silvia S

2014-02-01

The use of drug-loaded nanoparticles and microparticles has been increasing, especially for cosmetic and drug delivery purposes. In this work, a new microparticle formulation was developed for use in the healing process of skin burns in a composition of Aloe vera/vitamin E/chitosan. In order to observe the morphological properties, Raman and atomic force microscopy evaluation were performed. The biodistribution studies were analyzed by using a nuclear methodology, labeling the microparticles with Technetium-99m and in vivo test was procedure to analyzed the cicatrization process. The results of AFM analysis show the formation and the adherence property of the microparticles. Raman analyses show the distribution of each component in the microparticle. The nuclear method used shows that the biodistribution of the microparticles remained in the skin. The in vivo cicatrization test showed that the poloxamer gel containing the microparticles make a better cicatrization in relation to the other formulations tested. Copyright © 2013 Elsevier B.V. All rights reserved.

Study on color difference estimation method of medicine biochemical analysis

NASA Astrophysics Data System (ADS)

Wang, Chunhong; Zhou, Yue; Zhao, Hongxia; Sun, Jiashi; Zhou, Fengkun

2006-01-01

The biochemical analysis in medicine is an important inspection and diagnosis method in hospital clinic. The biochemical analysis of urine is one important item. The Urine test paper shows corresponding color with different detection project or different illness degree. The color difference between the standard threshold and the test paper color of urine can be used to judge the illness degree, so that further analysis and diagnosis to urine is gotten. The color is a three-dimensional physical variable concerning psychology, while reflectance is one-dimensional variable; therefore, the estimation method of color difference in urine test can have better precision and facility than the conventional test method with one-dimensional reflectance, it can make an accurate diagnose. The digital camera is easy to take an image of urine test paper and is used to carry out the urine biochemical analysis conveniently. On the experiment, the color image of urine test paper is taken by popular color digital camera and saved in the computer which installs a simple color space conversion (RGB -> XYZ -> L *a *b *)and the calculation software. Test sample is graded according to intelligent detection of quantitative color. The images taken every time were saved in computer, and the whole illness process will be monitored. This method can also use in other medicine biochemical analyses that have relation with color. Experiment result shows that this test method is quick and accurate; it can be used in hospital, calibrating organization and family, so its application prospect is extensive.

Data mining methods in the prediction of Dementia: A real-data comparison of the accuracy, sensitivity and specificity of linear discriminant analysis, logistic regression, neural networks, support vector machines, classification trees and random forests

PubMed Central

2011-01-01

Background Dementia and cognitive impairment associated with aging are a major medical and social concern. Neuropsychological testing is a key element in the diagnostic procedures of Mild Cognitive Impairment (MCI), but has presently a limited value in the prediction of progression to dementia. We advance the hypothesis that newer statistical classification methods derived from data mining and machine learning methods like Neural Networks, Support Vector Machines and Random Forests can improve accuracy, sensitivity and specificity of predictions obtained from neuropsychological testing. Seven non parametric classifiers derived from data mining methods (Multilayer Perceptrons Neural Networks, Radial Basis Function Neural Networks, Support Vector Machines, CART, CHAID and QUEST Classification Trees and Random Forests) were compared to three traditional classifiers (Linear Discriminant Analysis, Quadratic Discriminant Analysis and Logistic Regression) in terms of overall classification accuracy, specificity, sensitivity, Area under the ROC curve and Press'Q. Model predictors were 10 neuropsychological tests currently used in the diagnosis of dementia. Statistical distributions of classification parameters obtained from a 5-fold cross-validation were compared using the Friedman's nonparametric test. Results Press' Q test showed that all classifiers performed better than chance alone (p < 0.05). Support Vector Machines showed the larger overall classification accuracy (Median (Me) = 0.76) an area under the ROC (Me = 0.90). However this method showed high specificity (Me = 1.0) but low sensitivity (Me = 0.3). Random Forest ranked second in overall accuracy (Me = 0.73) with high area under the ROC (Me = 0.73) specificity (Me = 0.73) and sensitivity (Me = 0.64). Linear Discriminant Analysis also showed acceptable overall accuracy (Me = 0.66), with acceptable area under the ROC (Me = 0.72) specificity (Me = 0.66) and sensitivity (Me = 0.64). The remaining classifiers showed overall classification accuracy above a median value of 0.63, but for most sensitivity was around or even lower than a median value of 0.5. Conclusions When taking into account sensitivity, specificity and overall classification accuracy Random Forests and Linear Discriminant analysis rank first among all the classifiers tested in prediction of dementia using several neuropsychological tests. These methods may be used to improve accuracy, sensitivity and specificity of Dementia predictions from neuropsychological testing. PMID:21849043

Water impact analysis of space shuttle solid rocket motor by the finite element method

NASA Technical Reports Server (NTRS)

Buyukozturk, O.; Hibbitt, H. D.; Sorensen, E. P.

1974-01-01

Preliminary analysis showed that the doubly curved triangular shell elements were too stiff for these shell structures. The doubly curved quadrilateral shell elements were found to give much improved results. A total of six load cases were analyzed in this study. The load cases were either those resulting from a static test using reaction straps to simulate the drop conditions or under assumed hydrodynamic conditions resulting from a drop test. The latter hydrodynamic conditions were obtained through an emperical fit of available data. Results obtained from a linear analysis were found to be consistent with results obtained elsewhere with NASTRAN and BOSOR. The nonlinear analysis showed that the originally assumed loads would result in failure of the shell structures. The nonlinear analysis also showed that it was useful to apply internal pressure as a stabilizing influence on collapse. A final analysis with an updated estimate of load conditions resulted in linear behavior up to full load.

Comparing the Fit of Item Response Theory and Factor Analysis Models

ERIC Educational Resources Information Center

Maydeu-Olivares, Alberto; Cai, Li; Hernandez, Adolfo

2011-01-01

Linear factor analysis (FA) models can be reliably tested using test statistics based on residual covariances. We show that the same statistics can be used to reliably test the fit of item response theory (IRT) models for ordinal data (under some conditions). Hence, the fit of an FA model and of an IRT model to the same data set can now be…

Comparison between Standing Broad Jump test and Wingate test for assessing lower limb anaerobic power in elite sportsmen.

PubMed

Krishnan, Anup; Sharma, Deep; Bhatt, Madhu; Dixit, Apoorv; Pradeep, P

2017-04-01

Lower limb explosive power is an important motor quality for sporting performance and indicates use of anaerobic energy systems like stored ATP and Creatine phosphate system. Weightlifting, Fencing and Wrestling use it for monitoring and identification of potential sportsmen. The Wingate test and Standing Broad Jump (SBJ) test are reliable and accurate tests for its assessment. This study conducted on elite Indian sportsmen tries to analyse feasibility of use of the SBJ test in sports and military medicine when Wingate test is impractical. 95 elite sportsmen (51 Fencers, 17 Weight lifters and 27 Wrestlers) of a sports institute were administered Wingate cycle ergometer test and SBJ under standardised conditions. The results were analysed for mass and inter-discipline correlation. Analysis using Pearson's correlation showed significant positive correlation between Peak power ( r  = 0.446, p  < 0.0001) and SBJ (distance) in all sportsmen. Inter-sport correlation showed positive correlation between SBJ and peak power ( r  = 0.335, p  < 0.016) in Fencers and between SBJ, peak power ( r  = 0.686, p  < 0.002) in Weightlifters. Bland-Altman plot analysis showed that about 94% pairs of peak power and SBJ were within limits of agreement for each discipline as well as among all sportsmen. The test results show definite correlation and SBJ test can be used as a field test in performance monitoring, talent identification, military recruit screening and injury prevention.

Simulation System of Car Crash Test in C-NCAP Analysis Based on an Improved Apriori Algorithm*

NASA Astrophysics Data System (ADS)

Xiang, LI

In order to analysis car crash test in C-NCAP, an improved algorithm is given based on Apriori algorithm in this paper. The new algorithm is implemented with vertical data layout, breadth first searching, and intersecting. It takes advantage of the efficiency of vertical data layout and intersecting, and prunes candidate frequent item sets like Apriori. Finally, the new algorithm is applied in simulation of car crash test analysis system. The result shows that the relations will affect the C-NCAP test results, and it can provide a reference for the automotive design.

Parallel-vector computation for linear structural analysis and non-linear unconstrained optimization problems

NASA Technical Reports Server (NTRS)

Nguyen, D. T.; Al-Nasra, M.; Zhang, Y.; Baddourah, M. A.; Agarwal, T. K.; Storaasli, O. O.; Carmona, E. A.

1991-01-01

Several parallel-vector computational improvements to the unconstrained optimization procedure are described which speed up the structural analysis-synthesis process. A fast parallel-vector Choleski-based equation solver, pvsolve, is incorporated into the well-known SAP-4 general-purpose finite-element code. The new code, denoted PV-SAP, is tested for static structural analysis. Initial results on a four processor CRAY 2 show that using pvsolve reduces the equation solution time by a factor of 14-16 over the original SAP-4 code. In addition, parallel-vector procedures for the Golden Block Search technique and the BFGS method are developed and tested for nonlinear unconstrained optimization. A parallel version of an iterative solver and the pvsolve direct solver are incorporated into the BFGS method. Preliminary results on nonlinear unconstrained optimization test problems, using pvsolve in the analysis, show excellent parallel-vector performance indicating that these parallel-vector algorithms can be used in a new generation of finite-element based structural design/analysis-synthesis codes.

Statistical Analysis of Zebrafish Locomotor Response.

PubMed

Liu, Yiwen; Carmer, Robert; Zhang, Gaonan; Venkatraman, Prahatha; Brown, Skye Ashton; Pang, Chi-Pui; Zhang, Mingzhi; Ma, Ping; Leung, Yuk Fai

2015-01-01

Zebrafish larvae display rich locomotor behaviour upon external stimulation. The movement can be simultaneously tracked from many larvae arranged in multi-well plates. The resulting time-series locomotor data have been used to reveal new insights into neurobiology and pharmacology. However, the data are of large scale, and the corresponding locomotor behavior is affected by multiple factors. These issues pose a statistical challenge for comparing larval activities. To address this gap, this study has analyzed a visually-driven locomotor behaviour named the visual motor response (VMR) by the Hotelling's T-squared test. This test is congruent with comparing locomotor profiles from a time period. Different wild-type (WT) strains were compared using the test, which shows that they responded differently to light change at different developmental stages. The performance of this test was evaluated by a power analysis, which shows that the test was sensitive for detecting differences between experimental groups with sample numbers that were commonly used in various studies. In addition, this study investigated the effects of various factors that might affect the VMR by multivariate analysis of variance (MANOVA). The results indicate that the larval activity was generally affected by stage, light stimulus, their interaction, and location in the plate. Nonetheless, different factors affected larval activity differently over time, as indicated by a dynamical analysis of the activity at each second. Intriguingly, this analysis also shows that biological and technical repeats had negligible effect on larval activity. This finding is consistent with that from the Hotelling's T-squared test, and suggests that experimental repeats can be combined to enhance statistical power. Together, these investigations have established a statistical framework for analyzing VMR data, a framework that should be generally applicable to other locomotor data with similar structure.

Statistical Analysis of Zebrafish Locomotor Response

PubMed Central

Zhang, Gaonan; Venkatraman, Prahatha; Brown, Skye Ashton; Pang, Chi-Pui; Zhang, Mingzhi; Ma, Ping; Leung, Yuk Fai

2015-01-01

Zebrafish larvae display rich locomotor behaviour upon external stimulation. The movement can be simultaneously tracked from many larvae arranged in multi-well plates. The resulting time-series locomotor data have been used to reveal new insights into neurobiology and pharmacology. However, the data are of large scale, and the corresponding locomotor behavior is affected by multiple factors. These issues pose a statistical challenge for comparing larval activities. To address this gap, this study has analyzed a visually-driven locomotor behaviour named the visual motor response (VMR) by the Hotelling’s T-squared test. This test is congruent with comparing locomotor profiles from a time period. Different wild-type (WT) strains were compared using the test, which shows that they responded differently to light change at different developmental stages. The performance of this test was evaluated by a power analysis, which shows that the test was sensitive for detecting differences between experimental groups with sample numbers that were commonly used in various studies. In addition, this study investigated the effects of various factors that might affect the VMR by multivariate analysis of variance (MANOVA). The results indicate that the larval activity was generally affected by stage, light stimulus, their interaction, and location in the plate. Nonetheless, different factors affected larval activity differently over time, as indicated by a dynamical analysis of the activity at each second. Intriguingly, this analysis also shows that biological and technical repeats had negligible effect on larval activity. This finding is consistent with that from the Hotelling’s T-squared test, and suggests that experimental repeats can be combined to enhance statistical power. Together, these investigations have established a statistical framework for analyzing VMR data, a framework that should be generally applicable to other locomotor data with similar structure. PMID:26437184

Reliability, Validity, and Cross-Cultural Adaptation of the Turkish Version of the Bournemouth Questionnaire.

PubMed

Gunaydin, Gurkan; Citaker, Seyit; Meray, Jale; Cobanoglu, Gamze; Gunaydin, Ozge Ece; Hazar Kanik, Zeynep

2016-11-01

Validation of a self-report questionnaire. The purpose of this study was to investigate adaptation, validity, and reliability of the Turkish version of the Bournemouth Questionnaire. Low back pain is one of the most frequent disorders leading to activity limitation. This pain affects most of people in their lives. The most important point to evaluate patient's functional abilities and to decide a successful therapy procedure is to manage the assessment questionnaires precisely. One hundred ten patients with chronic low back pain were included in present study. To assess reliability, test-retest and internal consistency analyses were applied. The results of test-retest analysis were assessed by using Intraclass Correlation Coefficient method (95% confidence interval). For internal consistency, Cronbach alpha value was calculated. Validity of the questionnaire was assessed in terms of construct validity. For construct validity, factor analysis and convergent validity were tested. For convergent validity, total points of the Bournemouth Questionnaire were assessed with the total points of Quebec Back Pain Disability Scale and Roland Morris Disability Questionnaire by using Pearson correlation coefficient analysis. Cronbach alpha value was found 0.914, showing that this questionnaire has high internal consistency. The results of test-retest analysis were varying between 0.851 and 0.927, which shows that test-retest results are highly correlated. Factor analysis test indicated that this questionnaire had one factor. Pearson correlation coefficient of the Bournemouth Questionnaire with Roland Morris Disability Questionnaire was calculated 0.703 and it was found with Quebec Back Pain Disability Scale is 0.659. These results showed that the Bournemouth Questionnaire is very good correlated with Roland Morris Disability Questionnaire and Quebec Back Pain Disability Scale. The Turkish version of the Bournemouth Questionnaire is valid and reliable. 3.

Respiratory muscle endurance after training in athletes and non-athletes: A systematic review and meta-analysis.

PubMed

Sales, Ana Tereza do N; Fregonezi, Guilherme A de F; Ramsook, Andrew H; Guenette, Jordan A; Lima, Illia Nadinne D F; Reid, W Darlene

2016-01-01

The objectives of this systematic review was to evaluate the effects of respiratory muscle training (RMT) on respiratory muscle endurance (RME) and to determine the RME test that demonstrates the most consistent changes after RMT. Electronic searches were conducted in EMBASE, MEDLINE, COCHRANE CENTRAL, CINHAL and SPORTDiscus. The PEDro scale was used for quality assessment and meta-analysis were performed to compare effect sizes of different RME tests. Twenty studies met the inclusion criteria. Isocapnic hyperpnea training was performed in 40% of the studies. Meta-analysis showed that RMT improves RME in athletes (P = 0.0007) and non-athletes (P = 0.001). Subgroup analysis showed differences among tests; maximal sustainable ventilatory capacity (MSVC) and maximal sustainable threshold loading tests demonstrated significant improvement after RMT (P = 0.007; P = 0.003 respectively) compared to the maximal voluntary ventilation (MVV) (P = 0.11) in athletes whereas significant improvement after RMT was only shown by MSVC in non-athletes. The effect size of MSVC was greater compared to MVV in studies that performed both tests. The meta-analysis results provide evidence that RMT improves RME in athletes and non-athletes and MSVC test that examine endurance over several minutes are more sensitive to improvement after RMT. Copyright © 2015 Elsevier Ltd. All rights reserved.

The comparative performance of PMI estimation in skeletal remains by three methods (C-14, luminol test and OHI): analysis of 20 cases.

PubMed

Cappella, Annalisa; Gibelli, Daniele; Muccino, Enrico; Scarpulla, Valentina; Cerutti, Elisa; Caruso, Valentina; Sguazza, Emanuela; Mazzarelli, Debora; Cattaneo, Cristina

2015-01-27

When estimating post-mortem interval (PMI) in forensic anthropology, the only method able to give an unambiguous result is the analysis of C-14, although the procedure is expensive. Other methods, such as luminol tests and histological analysis, can be performed as preliminary investigations and may allow the operators to gain a preliminary indication concerning PMI, but they lack scientific verification, although luminol testing has been somewhat more accredited in the past few years. Such methods in fact may provide some help as they are inexpensive and can give a fast response, especially in the phase of preliminary investigations. In this study, 20 court cases of human skeletonized remains were dated by the C-14 method. For two cases, results were chronologically set after the 1950s; for one case, the analysis was not possible technically. The remaining 17 cases showed an archaeological or historical collocation. The same bone samples were also screened with histological examination and with the luminol test. Results showed that only four cases gave a positivity to luminol and a high Oxford Histology Index (OHI) score at the same time: among these, two cases were dated as recent by the radiocarbon analysis. Thus, only two false-positive results were given by the combination of these methods and no false negatives. Thus, the combination of two qualitative methods (luminol test and microscopic analysis) may represent a promising solution to cases where many fragments need to be quickly tested.

Cascaded image analysis for dynamic crack detection in material testing

NASA Astrophysics Data System (ADS)

Hampel, U.; Maas, H.-G.

Concrete probes in civil engineering material testing often show fissures or hairline-cracks. These cracks develop dynamically. Starting at a width of a few microns, they usually cannot be detected visually or in an image of a camera imaging the whole probe. Conventional image analysis techniques will detect fissures only if they show a width in the order of one pixel. To be able to detect and measure fissures with a width of a fraction of a pixel at an early stage of their development, a cascaded image analysis approach has been developed, implemented and tested. The basic idea of the approach is to detect discontinuities in dense surface deformation vector fields. These deformation vector fields between consecutive stereo image pairs, which are generated by cross correlation or least squares matching, show a precision in the order of 1/50 pixel. Hairline-cracks can be detected and measured by applying edge detection techniques such as a Sobel operator to the results of the image matching process. Cracks will show up as linear discontinuities in the deformation vector field and can be vectorized by edge chaining. In practical tests of the method, cracks with a width of 1/20 pixel could be detected, and their width could be determined at a precision of 1/50 pixel.

Arcjet Cathode Phenomena

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Haag, Thomas W.; Raquet, John F.

1989-01-01

Cathode tips made from a number of different materials were tested in a modular arcjet thruster in order to examine cathode phenomena. Periodic disassembly and examination, along with the data collected during testing, indicated that all of the tungsten-based materials behaved similarly despite the fact that in one of these samples the percentage of thorium oxide was doubled and another was 25 percent rhenium. The mass loss rate from a 2 percent thoriated rhenium cathode was found to be an order of magnitude greater than that observed using 2 percent thoriated tungsten. Detailed analysis of one of these cathode tips showed that the molten crater contained pure tungsten to a depth of about 150 microns. Problems with thermal stress cracking were encountered in the testing of a hafnium carbide tip. Post test analysis showed that the active area of the tip had chemically reacted with the propellant. A 100 hour continuous test was run at about 1 kW. Post test analysis revealed no dendrite formation, such as observed in a 30 kW arcjet lifetest, near the cathode crater. The cathodes from both this test and a previously run 1000 hour cycled test displayed nearly identical arc craters. Data and calculations indicate that the mass losses observed in testing can be explained by evaporation.

Arcjet cathode phenomena

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Haag, Thomas W.; Raquet, John F.

1989-01-01

Cathode tips made from a number of different materials were tested in a modular arcjet thruster in order to examine cathode phenomena. Periodic disassembly and examination, along with the data collected during testing, indicated that all of the tungsten-based materials behaved similarly despite the fact that in one of these samples the percentage of thorium oxide was doubled and another was 25 percent rhenium. The mass loss rate from a 2 percent thoriated rhenium cathode was found to be an order of magnitude greater than that observed using 2 percent thoriated tungsten. Detailed analysis of one of these cathode tips showed that the molten crater contained pure tungsten to a depth of about 150 microns. Problems with thermal stress cracking were encountered in the testing of a hafnium carbide tip. Post test analysis showed that the active area of the tip had chemically reacted with the propellant. A 100 hour continuous test was run at about 1 kW. Post test analysis revealed no dendrite formation, such as observed in a 30 kW arcjet lifetest, near the cathode crater. The cathodes from both this test and a previously run 1000 hour cycled test displayed nearly identical arc craters. Data and calculations indicate that the mass losses observed in testing can be explained by evaporation.

Perchlorate in Fertilizers

DTIC Science & Technology

1999-09-01

Harrington , showed that with respect to mixed water analysis containing TDS at greater 1,000 ppm, the performance of the AS-5 column is not as robust...to note, these raw test materials were heterogeneous. Regardless of mixing time and mesh quality, dividing the raw test materials for laboratory...raw test material was prepared and shipped to seven laboratories for blind analysis. The suspension was prepared by 4 mixing the solid sample with

Examination of Routine Practice Patterns in the Hospital Information Data Warehouse: Use of OLAP and Rough Set Analysis with Clinician Feedback

PubMed Central

Grant, Andrew; Grant, Gwyneth; Gagné, Jean; Blanchette, Carl; Comeau, Émilie; Brodeur, Guillaume; Dionne, Jonathon; Ayite, Alphonse; Synak, Piotr; Wroblewski, Jakub; Apanowitz, Cas

2001-01-01

The patient centred electronic patient record enables retrospective analysis of practice patterns as one means to assist clinicians adjust and improve their practice. An interrogation of the data-warehouse linking test use to Diagnostic Related Group (DRG) of one years data of the Sherbrooke University Hospital showed that one-third of patients used two-thirds of these diagnostic tests. Using RoughSets analysis, zones of repeated tests were demonstrated where results remained within stable limits. It was concluded that 30% of fluid and electrolyte testing was probably unnecessary. These findings led to an endorsement of changing the test request formats in the hospital information system from profiles to individual tests requiring justification.

Embedded Figures Test Performance in the Broader Autism Phenotype: A Meta-Analysis

ERIC Educational Resources Information Center

Cribb, Serena J.; Olaithe, Michelle; Di Lorenzo, Renata; Dunlop, Patrick D.; Maybery, Murray T.

2016-01-01

People with autism show superior performance to controls on the Embedded Figures Test (EFT). However, studies examining the relationship between autistic-like traits and EFT performance in neurotypical individuals have yielded inconsistent findings. To examine the inconsistency, a meta-analysis was conducted of studies that (a) compared high and…

Post-Flight Analysis of the Guidance, Navigation, and Control Performance During Orion Exploration Flight Test 1

NASA Technical Reports Server (NTRS)

Barth, Andrew; Mamich, Harvey; Hoelscher, Brian

2015-01-01

The first test flight of the Orion Multi-Purpose Crew Vehicle presented additional challenges for guidance, navigation and control as compared to a typical re-entry from the International Space Station or other Low Earth Orbit. An elevated re-entry velocity and steeper flight path angle were chosen to achieve aero-thermal flight test objectives. New IMU's, a GPS receiver, and baro altimeters were flight qualified to provide the redundant navigation needed for human space flight. The guidance and control systems must manage the vehicle lift vector in order to deliver the vehicle to a precision, coastal, water landing, while operating within aerodynamic load, reaction control system, and propellant constraints. Extensive pre-flight six degree-of-freedom analysis was performed that showed mission success for the nominal mission as well as in the presence of sensor and effector failures. Post-flight reconstruction analysis of the test flight is presented in this paper to show whether that all performance metrics were met and establish how well the pre-flight analysis predicted the in-flight performance.

Enhanced sulfidation xanthate flotation of malachite using ammonium ions as activator.

PubMed

Wu, Dandan; Ma, Wenhui; Mao, Yingbo; Deng, Jiushuai; Wen, Shuming

2017-05-18

In this study, ammonium ion was used to enhance the sulfidation flotation of malachite. The effect of ammonium ion on the sulfidation flotation of malachite was investigated using microflotation test, inductively coupled plasma (ICP) analysis, zeta potential measurements, and scanning electron microscope analysis (SEM). The results of microflotation test show that the addition of sodium sulfide and ammonium sulfate resulted in better sulfidation than the addition of sodium sulfide alone. The results of ICP analysis indicate that the dissolution of enhanced sulfurized malachite surface is significantly decreased. Zeta potential measurements indicate that a smaller isoelectric point value and a large number of copper-sulfide films formed on the malachite surface by enhancing sulfidation resulted in a large amount of sodium butyl xanthate absorbed onto the enhanced sulfurized malachite surface. EDS semi-quantitative analysis and XPS analysis show that malachite was easily sulfurized by sodium sulfide with ammonium ion. These results show that the addition of ammonium ion plays a significant role in the sulfidation of malachite and results in improved flotation performance.

The reliability and validity of the SF-8 with a conflict-affected population in northern Uganda.

PubMed

Roberts, Bayard; Browne, John; Ocaka, Kaducu Felix; Oyok, Thomas; Sondorp, Egbert

2008-12-02

The SF-8 is a health-related quality of life instrument that could provide a useful means of assessing general physical and mental health amongst populations affected by conflict. The purpose of this study was to test the validity and reliability of the SF-8 with a conflict-affected population in northern Uganda. A cross-sectional multi-staged, random cluster survey was conducted with 1206 adults in camps for internally displaced persons in Gulu and Amuru districts of northern Uganda. Data quality was assessed by analysing the number of incomplete responses to SF-8 items. Response distribution was analysed using aggregate endorsement frequency. Test-retest reliability was assessed in a separate smaller survey using the intraclass correlation test. Construct validity was measured using principal component analysis, and the Pearson Correlation test for item-summary score correlation and inter-instrument correlations. Known groups validity was assessed using a two sample t-test to evaluates the ability of the SF-8 to discriminate between groups known to have, and not have, physical and mental health problems. The SF-8 showed excellent data quality. It showed acceptable item response distribution based upon analysis of aggregate endorsement frequencies. Test-retest showed a good intraclass correlation of 0.61 for PCS and 0.68 for MCS. The principal component analysis indicated strong construct validity and concurred with the results of the validity tests by the SF-8 developers. The SF-8 also showed strong construct validity between the 8 items and PCS and MCS summary score, moderate inter-instrument validity, and strong known groups validity. This study provides evidence on the reliability and validity of the SF-8 amongst IDPs in northern Uganda.

The reliability and validity of the SF-8 with a conflict-affected population in northern Uganda

PubMed Central

Roberts, Bayard; Browne, John; Ocaka, Kaducu Felix; Oyok, Thomas; Sondorp, Egbert

2008-01-01

Background The SF-8 is a health-related quality of life instrument that could provide a useful means of assessing general physical and mental health amongst populations affected by conflict. The purpose of this study was to test the validity and reliability of the SF-8 with a conflict-affected population in northern Uganda. Methods A cross-sectional multi-staged, random cluster survey was conducted with 1206 adults in camps for internally displaced persons in Gulu and Amuru districts of northern Uganda. Data quality was assessed by analysing the number of incomplete responses to SF-8 items. Response distribution was analysed using aggregate endorsement frequency. Test-retest reliability was assessed in a separate smaller survey using the intraclass correlation test. Construct validity was measured using principal component analysis, and the Pearson Correlation test for item-summary score correlation and inter-instrument correlations. Known groups validity was assessed using a two sample t-test to evaluates the ability of the SF-8 to discriminate between groups known to have, and not have, physical and mental health problems. Results The SF-8 showed excellent data quality. It showed acceptable item response distribution based upon analysis of aggregate endorsement frequencies. Test-retest showed a good intraclass correlation of 0.61 for PCS and 0.68 for MCS. The principal component analysis indicated strong construct validity and concurred with the results of the validity tests by the SF-8 developers. The SF-8 also showed strong construct validity between the 8 items and PCS and MCS summary score, moderate inter-instrument validity, and strong known groups validity. Conclusion This study provides evidence on the reliability and validity of the SF-8 amongst IDPs in northern Uganda. PMID:19055716

Analysis of residual stress and hardness in regions of pre-manufactured and manual bends in fixation plates for maxillary advancement.

PubMed

Araújo, Marcelo Marotta; Lauria, Andrezza; Mendes, Marcelo Breno Meneses; Claro, Ana Paula Rosifini Alves; Claro, Cristiane Aparecida de Assis; Moreira, Roger William Fernandes

2015-12-01

The aim of this study was to analyze, through Vickers hardness test and photoelasticity analysis, pre-bent areas, manually bent areas, and areas without bends of 10-mm advancement pre-bent titanium plates (Leibinger system). The work was divided into three groups: group I-region without bend, group II-region of 90° manual bend, and group III-region of 90° pre-fabricated bends. All the materials were evaluated through hardness analysis by the Vickers hardness test, stress analysis by residual images obtained in a polariscope, and photoelastic analysis by reflection during the manual bending. The data obtained from the hardness tests were statistically analyzed using ANOVA and Tukey's tests at a significance level of 5 %. The pre-bent plate (group III) showed hardness means statistically significantly higher (P < 0.05) than those of the other groups (I-region without bends, II-90° manually bent region). Through the study of photoelastic reflection, it was possible to identify that the stress gradually increased, reaching a pink color (1.81 δ / λ), as the bending was performed. A general analysis of the results showed that the bent plate region of pre-bent titanium presented the best results.

Theoretical Analysis and Bench Tests of a Control-Surface Booster Employing a Variable Displacement Hydraulic Pump

NASA Technical Reports Server (NTRS)

Mathews, Charles W.; Kleckner, Harold F.

1947-01-01

The NACA is conducting a general investigation of servo-mechanisms for use in powering aircraft control surfaces. This paper presents a theoretical analysis and the results of bench tests of a control-booster system which employs a variable displacement hydraulic pump. The booster is intended for use in a flight investigation to determine the effects of various booster parameters on the handling qualities of airplanes. Such a flight investigation would aid in formulating specific requirements concerning the design of control boosters in general. Results of the theoretical analysis and the bench tests indicate that the subject booster is representative of types which show promise of satisfactory performance. The bench tests showed that the following desirable features were inherent in this booster system: (1) No lost motion or play in any part of the system; (2) no detectable lag between motion of the contra1 stick and control surface; and (3) Good agreement between control displacements and stick-force variations with no hysteresis in the stick-force characteristics. The final design configuration of this booster system showed no tendency to oscillate, overshoot, or have other undesirable transient characteristics common to boosters.

Reliability Measure of a Clinical Test: Appreciation of Music in Cochlear Implantees (AMICI)

PubMed Central

Cheng, Min-Yu; Spitzer, Jaclyn B.; Shafiro, Valeriy; Sheft, Stanley; Mancuso, Dean

2014-01-01

Purpose The goals of this study were (1) to investigate the reliability of a clinical music perception test, Appreciation of Music in Cochlear Implantees (AMICI), and (2) examine associations between the perception of music and speech. AMICI was developed as a clinical instrument for assessing music perception in persons with cochlear implants (CIs). The test consists of four subtests: (1) music versus environmental noise discrimination, (2) musical instrument identification (closed-set), (3) musical style identification (closed-set), and (4) identification of musical pieces (open-set). To be clinically useful, it is crucial for AMICI to demonstrate high test-retest reliability, so that CI users can be assessed and retested after changes in maps or programming strategies. Research Design Thirteen CI subjects were tested with AMICI for the initial visit and retested again 10–14 days later. Two speech perception tests (consonant-nucleus-consonant [CNC] and Bamford-Kowal-Bench Speech-in-Noise [BKB-SIN]) were also administered. Data Analysis Test-retest reliability and equivalence of the test’s three forms were analyzed using paired t-tests and correlation coefficients, respectively. Correlation analysis was also conducted between results from the music and speech perception tests. Results Results showed no significant difference between test and retest (p > 0.05) with adequate power (0.9) as well as high correlations between the three forms (Forms A and B, r = 0.91; Forms A and C, r = 0.91; Forms B and C, r = 0.95). Correlation analysis showed high correlation between AMICI and BKB-SIN (r = −0.71), and moderate correlation between AMICI and CNC (r = 0.4). Conclusions The study showed AMICI is highly reliable for assessing musical perception in CI users. PMID:24384082

Validation of structural analysis methods using the in-house liner cyclic rigs

NASA Technical Reports Server (NTRS)

Thompson, R. L.

1982-01-01

Test conditions and variables to be considered in each of the test rigs and test configurations, and also used in the validation of the structural predictive theories and tools, include: thermal and mechanical load histories (simulating an engine mission cycle; different boundary conditions; specimens and components of different dimensions and geometries; different materials; various cooling schemes and cooling hole configurations; several advanced burner liner structural design concepts; and the simulation of hot streaks. Based on these test conditions and test variables, the test matrices for each rig and configurations can be established to verify the predictive tools over as wide a range of test conditions as possible using the simplest possible tests. A flow chart for the thermal/structural analysis of a burner liner and how the analysis relates to the tests is shown schematically. The chart shows that several nonlinear constitutive theories are to be evaluated.

Analysis of strain gage reliability in F-100 jet engine testing at NASA Lewis Research Center

NASA Technical Reports Server (NTRS)

Holanda, R.

1983-01-01

A reliability analysis was performed on 64 strain gage systems mounted on the 3 rotor stages of the fan of a YF-100 engine. The strain gages were used in a 65 hour fan flutter research program which included about 5 hours of blade flutter. The analysis was part of a reliability improvement program. Eighty-four percent of the strain gages survived the test and performed satisfactorily. A post test analysis determined most failure causes. Five failures were caused by open circuits, three failed gages showed elevated circuit resistance, and one gage circuit was grounded. One failure was undetermined.

Influence of Stepped Osteotomy on Primary Stability of Implants Inserted in Low-Density Bone Sites: An In Vitro Study.

PubMed

Degidi, Marco; Daprile, Giuseppe; Piattelli, Adriano

The aims of this study were to evaluate the ability of a stepped osteotomy to improve dental implant primary stability in low-density bone sites and to investigate possible correlations between primary stability parameters. The study was performed on fresh humid bovine bone classified as type III. The test group consisted of 30 Astra Tech EV implants inserted following the protocol provided by the manufacturer. The first control group consisted of 30 Astra Tech EV implants inserted in sites without the underpreparation of the apical portion. The second control group consisted of 30 Astra Tech TX implants inserted following the protocol provided by the manufacturer. Implant insertion was performed at the predetermined 30 rpm. The insertion torque data were recorded and exported as a curve; using a trapezoidal integration technique, the area underlying the curve was calculated: this area represents the variable torque work (VTW). Peak insertion torque (pIT) and resonance frequency analysis (RFA) were also recorded. A Mann-Whitney test showed that the mean VTW was significantly higher in the test group compared with the first control and second control groups; furthermore, statistical analysis showed that pIT also was significantly higher in the test group compared with the first and second control groups. Analyzing RFA values, only the difference between the test group and second control group showed statistical significance. Pearson correlation analysis showed a very strong positive correlation between pIT and VTW values in all groups; furthermore, it showed a positive correlation between pIT and RFA values and between VTW and RFA values only in the test group. Within the limitations of an in vitro study, the results show that stepped osteotomy can be a viable method to improve implant primary stability in low-density bone sites, and that, when a traditional osteotomy method is performed, RFA presents no correlation with pIT and VTW.

Comparison of analytical methods for the determination of histamine in reference canned fish samples

NASA Astrophysics Data System (ADS)

Jakšić, S.; Baloš, M. Ž.; Mihaljev, Ž.; Prodanov Radulović, J.; Nešić, K.

2017-09-01

Two screening methods for histamine in canned fish, an enzymatic test and a competitive direct enzyme-linked immunosorbent assay (CD-ELISA), were compared with the reversed-phase liquid chromatography (RP-HPLC) standard method. For enzymatic and CD-ELISA methods, determination was conducted according to producers’ manuals. For RP-HPLC, histamine was derivatized with dansyl-chloride, followed by RP-HPLC and diode array detection. Results of analysis of canned fish, supplied as reference samples for proficiency testing, showed good agreement when histamine was present at higher concentrations (above 100 mg kg-1). At a lower level (16.95 mg kg-1), the enzymatic test produced some higher results. Generally, analysis of four reference samples according to CD-ELISA and RP-HPLC showed good agreement for histamine determination (r=0.977 in concentration range 16.95-216 mg kg-1) The results show that the applied enzymatic test and CD-ELISA appeared to be suitable screening methods for the determination of histamine in canned fish.

Predicting Performance on State Achievement Tests Using Curriculum-Based Measurement in Reading: A Multilevel Meta-Analysis

ERIC Educational Resources Information Center

Yeo, Seungsoo

2010-01-01

The purpose of this synthesis was to examine the relationship between Curriculum-Based Measurement (CBM) and statewide achievement tests in reading. A multilevel meta-analysis was used to calculate the correlation coefficient of the population for 27 studies that met the inclusion criteria. Results showed an overall large correlation coefficient…

Testing the mean for dependent business data.

PubMed

Liang, Jiajuan; Martin, Linda

2008-01-01

In business data analysis, it is well known that the comparison of several means is usually carried out by the F-test in analysis of variance under the assumption of independently collected data from all populations. This assumption, however, is likely to be violated in survey data collected from various questionnaires or time-series data. As a result, it is not justifiable or problematic to apply the traditional F-test to comparison of dependent means directly. In this article, we develop a generalized F-test for comparing population means with dependent data. Simulation studies show that the proposed test has a simple approximate null distribution and feasible finite-sample properties. Applications of the proposed test in analysis of survey data and time-series data are illustrated by two real datasets.

Sensitivity of cognitive tests in four cognitive domains in discriminating MDD patients from healthy controls: a meta-analysis.

PubMed

Lim, JaeHyoung; Oh, In Kyung; Han, Changsu; Huh, Yu Jeong; Jung, In-Kwa; Patkar, Ashwin A; Steffens, David C; Jang, Bo-Hyoung

2013-09-01

We performed a meta-analysis in order to determine which neuropsychological domains and tasks would be most sensitive for discriminating between patients with major depressive disorder (MDD) and healthy controls. Relevant articles were identified through a literature search of the PubMed and Cochrane Library databases for the period between January 1997 and May 2011. A meta-analysis was conducted using the standardized means of individual cognitive tests in each domain. The heterogeneity was assessed, and subgroup analyses according to age and medication status were performed to explore the sources of heterogeneity. A total of 22 trials involving 955 MDD patients and 7,664 healthy participants were selected for our meta-analysis. MDD patients showed significantly impaired results compared with healthy participants on the Digit Span and Continuous Performance Test in the attention domain; the Trail Making Test A (TMT-A) and the Digit Symbol Test in the processing speed domain; the Stroop Test, the Wisconsin Card Sorting Test, and Verbal Fluency in the executive function domain; and immediate verbal memory in the memory domain. The Finger Tapping Task, TMT-B, delayed verbal memory, and immediate and delayed visual memory failed to separate MDD patients from healthy controls. The results of subgroup analysis showed that performance of Verbal Fluency was significantly impaired in younger depressed patients (<60 years), and immediate visual memory was significantly reduced in depressed patients using antidepressants. Our findings have inevitable limitations arising from methodological issues inherent in the meta-analysis and we could not explain high heterogeneity between studies. Despite such limitations, current study has the strength of being the first meta-analysis which tried to specify cognitive function of depressed patients compared with healthy participants. And our findings may provide clinicians with further evidences that some cognitive tests in specific cognitive domains have sensitivity to discriminate MDD patients from healthy controls.

Testing an automated method to estimate ground-water recharge from streamflow records

USGS Publications Warehouse

Rutledge, A.T.; Daniel, C.C.

1994-01-01

The computer program, RORA, allows automated analysis of streamflow hydrographs to estimate ground-water recharge. Output from the program, which is based on the recession-curve-displacement method (often referred to as the Rorabaugh method, for whom the program is named), was compared to estimates of recharge obtained from a manual analysis of 156 years of streamflow record from 15 streamflow-gaging stations in the eastern United States. Statistical tests showed that there was no significant difference between paired estimates of annual recharge by the two methods. Tests of results produced by the four workers who performed the manual method showed that results can differ significantly between workers. Twenty-two percent of the variation between manual and automated estimates could be attributed to having different workers perform the manual method. The program RORA will produce estimates of recharge equivalent to estimates produced manually, greatly increase the speed od analysis, and reduce the subjectivity inherent in manual analysis.

The Effect of Group Therapy With Transactional Analysis Approach on Emotional Intelligence, Executive Functions and Drug Dependency.

PubMed

Forghani, Masoomeh; Ghanbari Hashem Abadi, Bahram Ali

2016-06-01

The aim of the present study was to evaluate the effect of group psychotherapy with transactional analysis (TA) approach on emotional intelligence (EI), executive functions and substance dependency among drug-addicts at rehabilitation centers in Mashhad city, Iran, in 2013. In this quasi-experimental study with pretest, posttest, case- control stages, 30 patients were selected from a rehabilitation center and randomly divided into two groups. The case group received 12 sessions of group psychotherapy with transactional analysis approach. Then the effects of independent variable (group psychotherapy with TA approach) on EI, executive function and drug dependency were assessed. The Bar-on test was used for EI, Stroop test for measuring executive function and morphine test, meth-amphetamines and B2 test for evaluating drug dependency. Data were analyzed using multifactorial covariance analysis, Levenes' analysis, MANCOVA, t-student and Pearson correlation coefficient tests t with SPSS software. Our results showed that group psychotherapy with the TA approach was effective in improving EI, executive functions and decreasing drug dependency (P < 0.05). The result of this study showed that group psychotherapy with TA approach has significant effects on addicts and prevents addiction recurrence by improving the coping capabilities and some mental functions of the subjects. However, there are some limitations regarding this study including follow-up duration and sample size.

Methodology for the Assessment of 3D Conduction Effects in an Aerothermal Wind Tunnel Test

NASA Technical Reports Server (NTRS)

Oliver, Anthony Brandon

2010-01-01

This slide presentation reviews a method for the assessment of three-dimensional conduction effects during test in a Aerothermal Wind Tunnel. The test objectives were to duplicate and extend tests that were performed during the 1960's on thermal conduction on proturberance on a flat plate. Slides review the 1D versus 3D conduction data reduction error, the analysis process, CFD-based analysis, loose coupling method that simulates a wind tunnel test run, verification of the CFD solution, Grid convergence, Mach number trend, size trends, and a Sumary of the CFD conduction analysis. Other slides show comparisons to pretest CFD at Mach 1.5 and 2.16 and the geometries of the models and grids.

Investigation of thiol derivatized gold nanoparticle sensors for gas analysis

NASA Astrophysics Data System (ADS)

Stephens, Jared S.

Analysis of volatile organic compounds (VOCs) in air and exhaled breath by sensor array is a very useful testing technique. It can provide non-invasive, fast, inexpensive testing for many diseases. Breath analysis has been very successful in identifying cancer and other diseases by using a chemiresistor sensor or array with gold nanoparticles to detect biomarkers. Acetone is a biomarker for diabetes and having a portable testing device could help to monitor diabetic and therapeutic progress. An advantage to this testing method is it is conducted at room temperature instead of 200 degrees Celsius. 3. The objective of this research is to determine the effect of thiol derivatized gold nanoparticles based on sensor(s) detection of VOCs. The VOCs to be tested are acetone, ethanol, and a mixture of acetone and ethanol. Each chip is tested under all three VOCs and three concentration levels (0.1, 1, and 5.0 ppm). VOC samples are used to test the sensors' ability to detect and differentiate VOCs. Sensors (also referred to as a chip) are prepared using several types of thiol derivatized gold nanoparticles. The factors are: thiol compound and molar volume loading of the thiol in synthesis. The average resistance results are used to determine the VOC selectivity of the sensors tested. The results show a trend of increasing resistance as VOC concentration is increased relative to dry air; which is used as baseline for VOCs. Several sensors show a high selectivity to one or more VOCs. Overall the 57 micromoles of 4-methoxy-toluenethiol sensor shows the strongest selectivity for VOCs tested. 3. Gerfen, Kurt. 2012. Detection of Acetone in Air Using Silver Ion Exchanged ZSM-5 and Zinc Oxide Sensing Films. Master of Science thesis, University of Louisville.

Testing for intracycle determinism in pseudoperiodic time series.

PubMed

Coelho, Mara C S; Mendes, Eduardo M A M; Aguirre, Luis A

2008-06-01

A determinism test is proposed based on the well-known method of the surrogate data. Assuming predictability to be a signature of determinism, the proposed method checks for intracycle (e.g., short-term) determinism in the pseudoperiodic time series for which standard methods of surrogate analysis do not apply. The approach presented is composed of two steps. First, the data are preprocessed to reduce the effects of seasonal and trend components. Second, standard tests of surrogate analysis can then be used. The determinism test is applied to simulated and experimental pseudoperiodic time series and the results show the applicability of the proposed test.

The psychometric properties of an Iranian translation of the Work Ability Index (WAI) questionnaire.

PubMed

Abdolalizadeh, M; Arastoo, A A; Ghsemzadeh, R; Montazeri, A; Ahmadi, K; Azizi, A

2012-09-01

This study was carried out to evaluate the psychometric properties of an Iranian translation of the Work Ability Index (WAI) questionnaire. In this methodological study, nurses and healthcare workers aged 40 years and older who worked in educational hospitals in Ahvaz (236 workers) in 2010, completed the questionnaire and 60 of the workers filled out the WAI questionnaire for the second time to ensure test-retest reliability. Forward-backward method was applied to translate the questionnaire from English into Persian. The psychometric properties of the Iranian translation of the WAI were assessed using the fallowing tests: Internal consistency (to test reliability), test-retest analysis, exploratory factor analysis (construct validity), discriminate validity by comparing the mean WAI score in two groups of the employees that had different levels of sick leave, criterion validity by determining the correlation between the Persian version of short form health survey (SF-36) and WAI score. Cronbach's alpha coefficient was estimated to be 0.79 and it was concluded that the internal consistency was high enough. The intraclass correlation coefficient was recognized to be 0.92. Factor analysis indicated three factors in the structure of the work ability including self-perceived work ability (24.5% of the variance), mental resources (22.23% of the variance), and presence of disease and health related limitation (18.55% of the variance). Statistical tests showed that this questionnaire was capable of discriminating two groups of employees who had different levels of sick leave. Criterion validity analysis showed that this instrument and all dimensions of the Iranian version of SF-36 were correlated significantly. Item correlation corrective for overlap showed the items tests had a good correlation except for one. The finding of the study showed that the Iranian version of the WAI is a reliable and valid measure of work ability and can be used both in research and practical activities.

Empirical retrocausality: Testing physics hypotheses with parapsychological experiments

NASA Astrophysics Data System (ADS)

Dobyns, York

2017-05-01

In 2011, Daryl Bem published a report of nine parapsychological experiments showing evidence of retrocausal information transfer. Earlier in 2016, the team of Bem, Tressoldi, Rabeyron, and Duggan published the results of a meta-analysis containing 81 independent replications of the original Bem experiments (total of 90 with the originals).[1] This much larger database continues to show positive results of generally comparable effect size, thus demonstrating that the effects claimed by Bem can be replicated by independent researchers and greatly strengthening the case for empirically observed retrocausation. Earlier (2011) work by this author showed how a modification of one of Bem's original experiments could be used to test the mechanism implicitly proposed by Echeverria, Klinkhammer, and Thorne to explain how retrocausal phenomena can exist without any risk of self-contradictory event sequences (time paradoxes). In light of the new publication and new evidence, the current work generalizes the previous analysis which was restricted to only one of Bem's experimental genres (precognitive approach and avoidance). The current analysis shows how minor modifications can be made in Bem's other experimental genres of retroactive priming, retroactive habituation, and retroactive facilitation of recall to test the EKT anti-paradox mechanism. If the EKT hypothesis is correct, the modified experiments, while continuing to show replicable retrocausal phenomena, will also show a characteristic pattern of distortion in the statistics of the random selections used to drive the experiments.

Criterion-Related Validity of the Distance- and Time-Based Walk/Run Field Tests for Estimating Cardiorespiratory Fitness: A Systematic Review and Meta-Analysis.

PubMed

Mayorga-Vega, Daniel; Bocanegra-Parrilla, Raúl; Ornelas, Martha; Viciana, Jesús

2016-01-01

The main purpose of the present meta-analysis was to examine the criterion-related validity of the distance- and time-based walk/run tests for estimating cardiorespiratory fitness among apparently healthy children and adults. Relevant studies were searched from seven electronic bibliographic databases up to August 2015 and through other sources. The Hunter-Schmidt's psychometric meta-analysis approach was conducted to estimate the population criterion-related validity of the following walk/run tests: 5,000 m, 3 miles, 2 miles, 3,000 m, 1.5 miles, 1 mile, 1,000 m, ½ mile, 600 m, 600 yd, ¼ mile, 15 min, 12 min, 9 min, and 6 min. From the 123 included studies, a total of 200 correlation values were analyzed. The overall results showed that the criterion-related validity of the walk/run tests for estimating maximum oxygen uptake ranged from low to moderate (rp = 0.42-0.79), with the 1.5 mile (rp = 0.79, 0.73-0.85) and 12 min walk/run tests (rp = 0.78, 0.72-0.83) having the higher criterion-related validity for distance- and time-based field tests, respectively. The present meta-analysis also showed that sex, age and maximum oxygen uptake level do not seem to affect the criterion-related validity of the walk/run tests. When the evaluation of an individual's maximum oxygen uptake attained during a laboratory test is not feasible, the 1.5 mile and 12 min walk/run tests represent useful alternatives for estimating cardiorespiratory fitness. As in the assessment with any physical fitness field test, evaluators must be aware that the performance score of the walk/run field tests is simply an estimation and not a direct measure of cardiorespiratory fitness.

[The research protocol VI: How to choose the appropriate statistical test. Inferential statistics].

PubMed

Flores-Ruiz, Eric; Miranda-Novales, María Guadalupe; Villasís-Keever, Miguel Ángel

2017-01-01

The statistical analysis can be divided in two main components: descriptive analysis and inferential analysis. An inference is to elaborate conclusions from the tests performed with the data obtained from a sample of a population. Statistical tests are used in order to establish the probability that a conclusion obtained from a sample is applicable to the population from which it was obtained. However, choosing the appropriate statistical test in general poses a challenge for novice researchers. To choose the statistical test it is necessary to take into account three aspects: the research design, the number of measurements and the scale of measurement of the variables. Statistical tests are divided into two sets, parametric and nonparametric. Parametric tests can only be used if the data show a normal distribution. Choosing the right statistical test will make it easier for readers to understand and apply the results.

Accuracy and Precision of Silicon Based Impression Media for Quantitative Areal Texture Analysis

PubMed Central

Goodall, Robert H.; Darras, Laurent P.; Purnell, Mark A.

2015-01-01

Areal surface texture analysis is becoming widespread across a diverse range of applications, from engineering to ecology. In many studies silicon based impression media are used to replicate surfaces, and the fidelity of replication defines the quality of data collected. However, while different investigators have used different impression media, the fidelity of surface replication has not been subjected to quantitative analysis based on areal texture data. Here we present the results of an analysis of the accuracy and precision with which different silicon based impression media of varying composition and viscosity replicate rough and smooth surfaces. Both accuracy and precision vary greatly between different media. High viscosity media tested show very low accuracy and precision, and most other compounds showed either the same pattern, or low accuracy and high precision, or low precision and high accuracy. Of the media tested, mid viscosity President Jet Regular Body and low viscosity President Jet Light Body (Coltène Whaledent) are the only compounds to show high levels of accuracy and precision on both surface types. Our results show that data acquired from different impression media are not comparable, supporting calls for greater standardisation of methods in areal texture analysis. PMID:25991505

Biplot evaluation of test environments and identification of mega-environment for sugarcane cultivars in China

PubMed Central

Luo, Jun; Pan, Yong-Bao; Que, Youxiong; Zhang, Hua; Grisham, Michael Paul; Xu, Liping

2015-01-01

Test environments and classification of regional ecological zones into mega environments are the two key components in regional testing of sugarcane cultivars. This study aims to provide the theoretical basis for test environment evaluation and ecological zone division for sugarcane cultivars. In the present study, sugarcane yield data from a three-year nationwide field trial involving 21 cultivars and 14 pilot test locations were analysed using both analysis of variance (ANOVA) and heritability adjusted-genotype main effect plus genotype-environment interaction (HA-GGE) biplot. The results showed that among the interactive factors, the GE interaction had the greatest impact, while the genotype and year interaction showed the lowest impact. Kaiyuan, Lincang and Baoshan of Yunnan, Zhangzhou and Fuzhou of Fujian, and Hechi, Liuzhou and Chongzuo of Guangxi, and Lingao of Hainan were ideal test environments with a demonstrated high efficiency in selecting new cultivars with a wide adaptability, whereas Baise of Guangxi was not. Based on HA-GGE biplot analysis, there are three ecological sugarcane production zones in China, the Southern China Inland Zone, the Southwestern Plateau Zone, and the Southern Coastal Zone. The HA-GGE biplot analysis here presents the ideal test environments and also identifies the mega-environment for sugarcane cultivars in China. PMID:26489689

Biplot evaluation of test environments and identification of mega-environment for sugarcane cultivars in China.

PubMed

Luo, Jun; Pan, Yong-Bao; Que, Youxiong; Zhang, Hua; Grisham, Michael Paul; Xu, Liping

2015-10-22

Test environments and classification of regional ecological zones into mega environments are the two key components in regional testing of sugarcane cultivars. This study aims to provide the theoretical basis for test environment evaluation and ecological zone division for sugarcane cultivars. In the present study, sugarcane yield data from a three-year nationwide field trial involving 21 cultivars and 14 pilot test locations were analysed using both analysis of variance (ANOVA) and heritability adjusted-genotype main effect plus genotype-environment interaction (HA-GGE) biplot. The results showed that among the interactive factors, the GE interaction had the greatest impact, while the genotype and year interaction showed the lowest impact. Kaiyuan, Lincang and Baoshan of Yunnan, Zhangzhou and Fuzhou of Fujian, and Hechi, Liuzhou and Chongzuo of Guangxi, and Lingao of Hainan were ideal test environments with a demonstrated high efficiency in selecting new cultivars with a wide adaptability, whereas Baise of Guangxi was not. Based on HA-GGE biplot analysis, there are three ecological sugarcane production zones in China, the Southern China Inland Zone, the Southwestern Plateau Zone, and the Southern Coastal Zone. The HA-GGE biplot analysis here presents the ideal test environments and also identifies the mega-environment for sugarcane cultivars in China.

Preliminary Analysis of the 30-m UltraBoom Flight Test

NASA Technical Reports Server (NTRS)

Agnes, Gregory S.; Abelson, Robert D.; Miyake, Robert; Lin, John K. H.; Welsh, Joe; Watson, Judith J.

2005-01-01

Future NASA missions require long, ultra-lightweight booms to enable solar sails, large sunshields, and other gossamer-type spacecraft structures. The space experiment discussed in this paper will flight validate the non-traditional ultra lightweight rigidizable, inflatable, isogrid structure utilizing graphite shape memory polymer (GR/SMP) called UltraBoom(TradeMark). The focus of this paper is the analysis of the 3-m ground test article. The primary objective of the mission is to show that a combination of ground testing and analysis can predict the on-orbit performance of an ultra lightweight boom that is scalable, predictable, and thermomechanically stable.

A rule-based software test data generator

NASA Technical Reports Server (NTRS)

Deason, William H.; Brown, David B.; Chang, Kai-Hsiung; Cross, James H., II

1991-01-01

Rule-based software test data generation is proposed as an alternative to either path/predicate analysis or random data generation. A prototype rule-based test data generator for Ada programs is constructed and compared to a random test data generator. Four Ada procedures are used in the comparison. Approximately 2000 rule-based test cases and 100,000 randomly generated test cases are automatically generated and executed. The success of the two methods is compared using standard coverage metrics. Simple statistical tests showing that even the primitive rule-based test data generation prototype is significantly better than random data generation are performed. This result demonstrates that rule-based test data generation is feasible and shows great promise in assisting test engineers, especially when the rule base is developed further.

Genetic variability and resistance of cultivars of cowpea [Vigna unguiculata (L.) Walp] to cowpea weevil (Callosobruchus maculatus Fabr.).

PubMed

Vila Nova, M X; Leite, N G A; Houllou, L M; Medeiros, L V; Lira Neto, A C; Hsie, B S; Borges-Paluch, L R; Santos, B S; Araujo, C S F; Rocha, A A; Costa, A F

2014-03-31

The cowpea weevil (Callosobruchus maculatus Fabr.) is the most destructive pest of the cowpea bean; it reduces seed quality. To control this pest, resistance testing combined with genetic analysis using molecular markers has been widely applied in research. Among the markers that show reliable results, the inter-simple sequence repeats (ISSRs) (microsatellites) are noteworthy. This study was performed to evaluate the resistance of 27 cultivars of cowpea bean to cowpea weevil. We tested the resistance related to the genetic variability of these cultivars using ISSR markers. To analyze the resistance of cultivars to weevil, a completely randomized test design with 4 replicates and 27 treatments was adopted. Five pairs of the insect were placed in 30 grains per replicate. Analysis of variance showed that the number of eggs and emerged insects were significantly different in the treatments, and the means were compared by statistical tests. The analysis of the large genetic variability in all cultivars resulted in the formation of different groups. The test of resistance showed that the cultivar Inhuma was the most sensitive to both number of eggs and number of emerged adults, while the TE96-290-12-G and MNC99-537-F4 (BRS Tumucumaque) cultivars were the least sensitive to the number of eggs and the number of emerged insects, respectively.

RSRM nozzle fixed housing cooldown test

NASA Technical Reports Server (NTRS)

Bolieau, D. J.

1989-01-01

Flight 5 aft segments with nozzles were exposed to -17 F temperatures while awaiting shipment to KSC in February, 1989. No records were found which show that any previous nozzles were exposed to air temperatures as low as those seen by the Flight 5 nozzles. Thermal analysis shows that the temperature of the fixed housing, and forward and aft exit cone components dropped as low as -10 F. Structural analysis of the nozzles at these low temperatures show the forward and aft exit cone adhesive bonds to have a positive margin of safety, based on a 2.0 safety factor. These analyses show the normal and shear stresses in the fixed housing bond as low values. However, the hoop and meridinal stresses were predicted to be in the 4000 psi range; the failure stress allowable of EA913NA adhesive at -7 F. If the bonds did break in directions perpendicular to the surfaces, called bond crazing, no normal bond strength would be lost. Testing was conducted in two phases, showing that no degradation to the adhesive bonds occurred while the Flight 5 nozzles were subjected to subzero temperatures. The results of these tests are documented. Phase 1 testing cooled a full-scale RSRM insulated fixed housing to -13 F, with extensive bondline inspections. Phase 2 testing cooled the witness panel adhesive tensile buttions to -13 F, with failure strengths recorded before, during, and after the cooldown.

Generating linear regression model to predict motor functions by use of laser range finder during TUG.

PubMed

Adachi, Daiki; Nishiguchi, Shu; Fukutani, Naoto; Hotta, Takayuki; Tashiro, Yuto; Morino, Saori; Shirooka, Hidehiko; Nozaki, Yuma; Hirata, Hinako; Yamaguchi, Moe; Yorozu, Ayanori; Takahashi, Masaki; Aoyama, Tomoki

2017-05-01

The purpose of this study was to investigate which spatial and temporal parameters of the Timed Up and Go (TUG) test are associated with motor function in elderly individuals. This study included 99 community-dwelling women aged 72.9 ± 6.3 years. Step length, step width, single support time, variability of the aforementioned parameters, gait velocity, cadence, reaction time from starting signal to first step, and minimum distance between the foot and a marker placed to 3 in front of the chair were measured using our analysis system. The 10-m walk test, five times sit-to-stand (FTSTS) test, and one-leg standing (OLS) test were used to assess motor function. Stepwise multivariate linear regression analysis was used to determine which TUG test parameters were associated with each motor function test. Finally, we calculated a predictive model for each motor function test using each regression coefficient. In stepwise linear regression analysis, step length and cadence were significantly associated with the 10-m walk test, FTSTS and OLS test. Reaction time was associated with the FTSTS test, and step width was associated with the OLS test. Each predictive model showed a strong correlation with the 10-m walk test and OLS test (P < 0.01), which was not significant higher correlation than TUG test time. We showed which TUG test parameters were associated with each motor function test. Moreover, the TUG test time regarded as the lower extremity function and mobility has strong predictive ability in each motor function test. Copyright © 2017 The Japanese Orthopaedic Association. Published by Elsevier B.V. All rights reserved.

Learning Factors Transfer Analysis: Using Learning Curve Analysis to Automatically Generate Domain Models

ERIC Educational Resources Information Center

Pavlik, Philip I. Jr.; Cen, Hao; Koedinger, Kenneth R.

2009-01-01

This paper describes a novel method to create a quantitative model of an educational content domain of related practice item-types using learning curves. By using a pairwise test to search for the relationships between learning curves for these item-types, we show how the test results in a set of pairwise transfer relationships that can be…

[The Freiburg monosyllable word test in postoperative cochlear implant diagnostics].

PubMed

Hey, M; Brademann, G; Ambrosch, P

2016-08-01

The Freiburg monosyllable word test represents a central tool of postoperative cochlear implant (CI) diagnostics. The objective of this study is to test the equivalence of different word lists by analysing word comprehension. For patients whose CI has been implanted for more than 5 years, the distribution of suprathreshold speech intelligibility outcomes will also be analysed. In a retrospective data analysis, speech understanding for 626 CI users word correct scores were evaluated using a total of 5211 lists with 20 words each. The analysis of word comprehension within each list shows differences in mean and in the kind of distribution function. There are lists which show a significant difference of their mean word recognition to the overall mean. The Freiburg monosyllable word test is easy to administer at suprathreshold speech level for CI recipients, and typically has a saturation level above 80 %. The Freiburg monosyllable word test can be performed successfully by the majority of CI patients. The limited balance of the test lists elicits the conclusion that an adaptive test procedure with the Freiburg monosyllable test does not make sense. The Freiburg monosyllable test can be restructured by resorting all words across lists, or by omitting individual words of a test list to increase the reliability of the test. The results show that speech intelligibility in quiet should also be investigated in CI recipients al levels below 70 dB.

Association analysis of multiple traits by an approach of combining P values.

PubMed

Chen, Lili; Wang, Yong; Zhou, Yajing

2018-03-01

Increasing evidence shows that one variant can affect multiple traits, which is a widespread phenomenon in complex diseases. Joint analysis of multiple traits can increase statistical power of association analysis and uncover the underlying genetic mechanism. Although there are many statistical methods to analyse multiple traits, most of these methods are usually suitable for detecting common variants associated with multiple traits. However, because of low minor allele frequency of rare variant, these methods are not optimal for rare variant association analysis. In this paper, we extend an adaptive combination of P values method (termed ADA) for single trait to test association between multiple traits and rare variants in the given region. For a given region, we use reverse regression model to test each rare variant associated with multiple traits and obtain the P value of single-variant test. Further, we take the weighted combination of these P values as the test statistic. Extensive simulation studies show that our approach is more powerful than several other comparison methods in most cases and is robust to the inclusion of a high proportion of neutral variants and the different directions of effects of causal variants.

An analytic data analysis method for oscillatory slug tests.

PubMed

Chen, Chia-Shyun

2006-01-01

An analytical data analysis method is developed for slug tests in partially penetrating wells in confined or unconfined aquifers of high hydraulic conductivity. As adapted from the van der Kamp method, the determination of the hydraulic conductivity is based on the occurrence times and the displacements of the extreme points measured from the oscillatory data and their theoretical counterparts available in the literature. This method is applied to two sets of slug test response data presented by Butler et al.: one set shows slow damping with seven discernable extremities, and the other shows rapid damping with three extreme points. The estimates of the hydraulic conductivity obtained by the analytic method are in good agreement with those determined by an available curve-matching technique.

Exploring the moderating role of context on the mathematics performance of females under stereotype threat: a meta-analysis.

PubMed

Picho, Katherine; Rodriguez, Ariel; Finnie, Lauren

2013-01-01

The current meta-analysis synthesized 17 years of research on stereotype threat (ST). Specifically, it examined the moderating effect of contextual factors on ST. Findings revealed that, on average, females in ST conditions performed less well on mathematics tests than their control counterparts (d =|10.24|). Results also showed that females did not benefit more from female-only testing situations, or testing contexts where they formed the majority. Nevertheless, the trend in ST effects differed by broader contextual factors like geography and level of education, with females in countries with small gender-gaps showing better performance under ST conditions, and ST effects being greater for students in middle and high school compared to college students.

Analysis of EUVE Experiment Results

NASA Technical Reports Server (NTRS)

Horan, Stephen

1996-01-01

A series of tests to validate an antenna pointing concept for spin-stabilized satellites using a data relay satellite are described. These tests show that proper antenna pointing on an inertially-stabilized spacecraft can lead to significant access time through the relay satellite even without active antenna pointing. We summarize the test results, the simulations to model the effects of antenna pattern and space loss, and the expected contact times. We also show how antenna beam width affects the results.

Objective Assessment of Activity Limitation in Glaucoma with Smartphone Virtual Reality Goggles: A Pilot Study.

PubMed

Goh, Rachel L Z; Kong, Yu Xiang George; McAlinden, Colm; Liu, John; Crowston, Jonathan G; Skalicky, Simon E

2018-01-01

To evaluate the use of smartphone-based virtual reality to objectively assess activity limitation in glaucoma. Cross-sectional study of 93 patients (54 mild, 22 moderate, 17 severe glaucoma). Sociodemographics, visual parameters, Glaucoma Activity Limitation-9 and Visual Function Questionnaire - Utility Index (VFQ-UI) were collected. Mean age was 67.4 ± 13.2 years; 52.7% were male; 65.6% were driving. A smartphone placed inside virtual reality goggles was used to administer the Virtual Reality Glaucoma Visual Function Test (VR-GVFT) to participants, consisting of three parts: stationary, moving ball, driving. Rasch analysis and classical validity tests were conducted to assess performance of VR-GVFT. Twenty-four of 28 stationary test items showed acceptable fit to the Rasch model (person separation 3.02, targeting 0). Eleven of 12 moving ball test items showed acceptable fit (person separation 3.05, targeting 0). No driving test items showed acceptable fit. Stationary test person scores showed good criterion validity, differentiating between glaucoma severity groups ( P = 0.014); modest convergence validity, with mild to moderate correlation with VFQ-UI, better eye (BE) mean deviation, BE pattern deviation, BE central scotoma, worse eye (WE) visual acuity, and contrast sensitivity (CS) in both eyes ( R = 0.243-0.381); and suboptimal divergent validity. Multivariate analysis showed that lower WE CS ( P = 0.044) and greater age ( P = 0.009) were associated with worse stationary test person scores. Smartphone-based virtual reality may be a portable objective simulation test of activity limitation related to glaucomatous visual loss. The use of simulated virtual environments could help better understand the activity limitations that affect patients with glaucoma.

Objective Assessment of Activity Limitation in Glaucoma with Smartphone Virtual Reality Goggles: A Pilot Study

PubMed Central

Goh, Rachel L. Z.; McAlinden, Colm; Liu, John; Crowston, Jonathan G.; Skalicky, Simon E.

2018-01-01

Purpose To evaluate the use of smartphone-based virtual reality to objectively assess activity limitation in glaucoma. Methods Cross-sectional study of 93 patients (54 mild, 22 moderate, 17 severe glaucoma). Sociodemographics, visual parameters, Glaucoma Activity Limitation-9 and Visual Function Questionnaire – Utility Index (VFQ-UI) were collected. Mean age was 67.4 ± 13.2 years; 52.7% were male; 65.6% were driving. A smartphone placed inside virtual reality goggles was used to administer the Virtual Reality Glaucoma Visual Function Test (VR-GVFT) to participants, consisting of three parts: stationary, moving ball, driving. Rasch analysis and classical validity tests were conducted to assess performance of VR-GVFT. Results Twenty-four of 28 stationary test items showed acceptable fit to the Rasch model (person separation 3.02, targeting 0). Eleven of 12 moving ball test items showed acceptable fit (person separation 3.05, targeting 0). No driving test items showed acceptable fit. Stationary test person scores showed good criterion validity, differentiating between glaucoma severity groups (P = 0.014); modest convergence validity, with mild to moderate correlation with VFQ-UI, better eye (BE) mean deviation, BE pattern deviation, BE central scotoma, worse eye (WE) visual acuity, and contrast sensitivity (CS) in both eyes (R = 0.243–0.381); and suboptimal divergent validity. Multivariate analysis showed that lower WE CS (P = 0.044) and greater age (P = 0.009) were associated with worse stationary test person scores. Conclusions Smartphone-based virtual reality may be a portable objective simulation test of activity limitation related to glaucomatous visual loss. Translational Relevance The use of simulated virtual environments could help better understand the activity limitations that affect patients with glaucoma. PMID:29372112

Ultrasonic test of resistance spot welds based on wavelet package analysis.

PubMed

Liu, Jing; Xu, Guocheng; Gu, Xiaopeng; Zhou, Guanghao

2015-02-01

In this paper, ultrasonic test of spot welds for stainless steel sheets has been studied. It is indicated that traditional ultrasonic signal analysis in either time domain or frequency domain remains inadequate to evaluate the nugget diameter of spot welds. However, the method based on wavelet package analysis in time-frequency domain can easily distinguish the nugget from the corona bond by extracting high-frequency signals in different positions of spot welds, thereby quantitatively evaluating the nugget diameter. The results of ultrasonic test fit the actual measured value well. Mean value of normal distribution of error statistics is 0.00187, and the standard deviation is 0.1392. Furthermore, the quality of spot welds was evaluated, and it is showed ultrasonic nondestructive test based on wavelet packet analysis can be used to evaluate the quality of spot welds, and it is more reliable than single tensile destructive test. Copyright © 2014 Elsevier B.V. All rights reserved.

A decision impact, decision conflict and economic assessment of routine Oncotype DX testing of 146 women with node-negative or pNImi, ER-positive breast cancer in the U.K.

PubMed

Holt, S; Bertelli, G; Humphreys, I; Valentine, W; Durrani, S; Pudney, D; Rolles, M; Moe, M; Khawaja, S; Sharaiha, Y; Brinkworth, E; Whelan, S; Jones, S; Bennett, H; Phillips, C J

2013-06-11

Tumour gene expression analysis is useful in predicting adjuvant chemotherapy benefit in early breast cancer patients. This study aims to examine the implications of routine Oncotype DX testing in the U.K. Women with oestrogen receptor positive (ER+), pNO or pN1mi breast cancer were assessed for adjuvant chemotherapy and subsequently offered Oncotype DX testing, with changes in chemotherapy decisions recorded. A subset of patients completed questionnaires about their uncertainties regarding chemotherapy decisions pre- and post-testing. All patients were asked to complete a diary of medical interactions over the next 6 months, from which economic data were extracted to model the cost-effectiveness of testing. Oncotype DX testing resulted in changes in chemotherapy decisions in 38 of 142 (26.8%) women, with 26 of 57 (45.6%) spared chemotherapy and 12 of 85 (14.1%) requiring chemotherapy when not initially recommended (9.9% reduction overall). Decision conflict analysis showed that Oncotype DX testing increased patients' confidence in treatment decision making. Economic analysis showed that routine Oncotype DX testing costs £6232 per quality-adjusted life year gained. Oncotype DX decreased chemotherapy use and increased confidence in treatment decision making in patients with ER+ early-stage breast cancer. Based on these findings, Oncotype DX is cost-effective in the UK setting.

Construct exploit constraint in crash analysis by bypassing canary

NASA Astrophysics Data System (ADS)

Huang, Ning; Huang, Shuguang; Huang, Hui; Chang, Chao

2017-08-01

Selective symbolic execution is a common program testing technology. Developed on the basis of it, some crash analysis systems are often used to test the fragility of the program by constructing exploit constraints, such as CRAX. From the study of crash analysis based on symbolic execution, this paper find that this technology cannot bypass the canary stack protection mechanisms. This paper makes the improvement uses the API hook in Linux. Experimental results show that the use of API hook can effectively solve the problem that crash analysis cannot bypass the canary protection.

LANDSAT-4 image data quality analysis for energy related applications. [nuclear power plant sites

NASA Technical Reports Server (NTRS)

Wukelic, G. E. (Principal Investigator)

1983-01-01

No useable LANDSAT 4 TM data were obtained for the Hanford site in the Columbia Plateau region, but TM simulator data for a Virginia Electric Company nuclear power plant was used to test image processing algorithms. Principal component analyses of this data set clearly indicated that thermal plumes in surface waters used for reactor cooling would be discrenible. Image processing and analysis programs were successfully testing using the 7 band Arkansas test scene and preliminary analysis of TM data for the Savanah River Plant shows that current interactive, image enhancement, analysis and integration techniques can be effectively used for LANDSAT 4 data. Thermal band data appear adequate for gross estimates of thermal changes occurring near operating nuclear facilities especially in surface water bodies being used for reactor cooling purposes. Additional image processing software was written and tested which provides for more rapid and effective analysis of the 7 band TM data.

Heave-pitch-roll analysis and testing of air cushion landing systems

NASA Technical Reports Server (NTRS)

Boghani, A. B.; Captain, K. M.; Wormley, D. N.

1978-01-01

The analytical tools (analysis and computer simulation) needed to explain and predict the dynamic operation of air cushion landing systems (ACLS) is described. The following tasks were performed: the development of improved analytical models for the fan and the trunk; formulation of a heave pitch roll analysis for the complete ACLS; development of a general purpose computer simulation to evaluate landing and taxi performance of an ACLS equipped aircraft; and the verification and refinement of the analysis by comparison with test data obtained through lab testing of a prototype cushion. Demonstration of simulation capabilities through typical landing and taxi simulation of an ACLS aircraft are given. Initial results show that fan dynamics have a major effect on system performance. Comparison with lab test data (zero forward speed) indicates that the analysis can predict most of the key static and dynamic parameters (pressure, deflection, acceleration, etc.) within a margin of a 10 to 25 percent.

Some applications of categorical data analysis to epidemiological studies.

PubMed Central

Grizzle, J E; Koch, G G

1979-01-01

Several examples of categorized data from epidemiological studies are analyzed to illustrate that more informative analysis than tests of independence can be performed by fitting models. All of the analyses fit into a unified conceptual framework that can be performed by weighted least squares. The methods presented show how to calculate point estimate of parameters, asymptotic variances, and asymptotically valid chi 2 tests. The examples presented are analysis of relative risks estimated from several 2 x 2 tables, analysis of selected features of life tables, construction of synthetic life tables from cross-sectional studies, and analysis of dose-response curves. PMID:540590

The use of regression analysis in determining reference intervals for low hematocrit and thrombocyte count in multiple electrode aggregometry and platelet function analyzer 100 testing of platelet function.

PubMed

Kuiper, Gerhardus J A J M; Houben, Rik; Wetzels, Rick J H; Verhezen, Paul W M; Oerle, Rene van; Ten Cate, Hugo; Henskens, Yvonne M C; Lancé, Marcus D

2017-11-01

Low platelet counts and hematocrit levels hinder whole blood point-of-care testing of platelet function. Thus far, no reference ranges for MEA (multiple electrode aggregometry) and PFA-100 (platelet function analyzer 100) devices exist for low ranges. Through dilution methods of volunteer whole blood, platelet function at low ranges of platelet count and hematocrit levels was assessed on MEA for four agonists and for PFA-100 in two cartridges. Using (multiple) regression analysis, 95% reference intervals were computed for these low ranges. Low platelet counts affected MEA in a positive correlation (all agonists showed r 2 ≥ 0.75) and PFA-100 in an inverse correlation (closure times were prolonged with lower platelet counts). Lowered hematocrit did not affect MEA testing, except for arachidonic acid activation (ASPI), which showed a weak positive correlation (r 2 = 0.14). Closure time on PFA-100 testing was inversely correlated with hematocrit for both cartridges. Regression analysis revealed different 95% reference intervals in comparison with originally established intervals for both MEA and PFA-100 in low platelet or hematocrit conditions. Multiple regression analysis of ASPI and both tests on the PFA-100 for combined low platelet and hematocrit conditions revealed that only PFA-100 testing should be adjusted for both thrombocytopenia and anemia. 95% reference intervals were calculated using multiple regression analysis. However, coefficients of determination of PFA-100 were poor, and some variance remained unexplained. Thus, in this pilot study using (multiple) regression analysis, we could establish reference intervals of platelet function in anemia and thrombocytopenia conditions on PFA-100 and in thrombocytopenia conditions on MEA.

Evaluation of the black light test for screening aflatoxin-contaminated maize in the Brazilian food industry.

PubMed

Gloria, E M; Fonseca, H; Calori-Domingues, M A; Souza, I M

1998-01-01

The results of the black light test for aflatoxin-contaminated maize carried out in a large food factory in the State of São Paulo was evaluated against bi-directional thin layer chromatography (TLC) analysis for 286 samples of maize. All 286 samples were accepted by the black light test (< 7 fluorescent points), however, the results from TLC analysis showed that 96 samples were contaminated and 14 showed aflatoxin B1 contamination levels higher than 20 micrograms/kg. There were 14 false negative results and no false positives and out of the 14 samples, six did not show visible fluorescent points. If the rejection criterion of one or more fluorescent points were applied, the six samples would be accepted by the black light test. But, in this case, 95 samples would be rejected and 87 results would be false positives because they did not have contamination levels over 20 micrograms/kg which is the acceptance limit of the black light test. The results indicate that the black light test, as utilized by this factory, was not able to indicate lots with possible contamination and the black light test, as recommended in the literature, would produce a high number of false positives. It is necessary to make more studies on the use of black light as a screening test for possible aflatoxin B1-contaminated maize.

Evaluation of hemifield sector analysis protocol in multifocal visual evoked potential objective perimetry for the diagnosis and early detection of glaucomatous field defects.

PubMed

Mousa, Mohammad F; Cubbidge, Robert P; Al-Mansouri, Fatima; Bener, Abdulbari

2014-02-01

Multifocal visual evoked potential (mfVEP) is a newly introduced method used for objective visual field assessment. Several analysis protocols have been tested to identify early visual field losses in glaucoma patients using the mfVEP technique, some were successful in detection of field defects, which were comparable to the standard automated perimetry (SAP) visual field assessment, and others were not very informative and needed more adjustment and research work. In this study we implemented a novel analysis approach and evaluated its validity and whether it could be used effectively for early detection of visual field defects in glaucoma. Three groups were tested in this study; normal controls (38 eyes), glaucoma patients (36 eyes) and glaucoma suspect patients (38 eyes). All subjects had a two standard Humphrey field analyzer (HFA) test 24-2 and a single mfVEP test undertaken in one session. Analysis of the mfVEP results was done using the new analysis protocol; the hemifield sector analysis (HSA) protocol. Analysis of the HFA was done using the standard grading system. Analysis of mfVEP results showed that there was a statistically significant difference between the three groups in the mean signal to noise ratio (ANOVA test, p < 0.001 with a 95% confidence interval). The difference between superior and inferior hemispheres in all subjects were statistically significant in the glaucoma patient group in all 11 sectors (t-test, p < 0.001), partially significant in 5 / 11 (t-test, p < 0.01), and no statistical difference in most sectors of the normal group (1 / 11 sectors was significant, t-test, p < 0.9). Sensitivity and specificity of the HSA protocol in detecting glaucoma was 97% and 86%, respectively, and for glaucoma suspect patients the values were 89% and 79%, respectively. The new HSA protocol used in the mfVEP testing can be applied to detect glaucomatous visual field defects in both glaucoma and glaucoma suspect patients. Using this protocol can provide information about focal visual field differences across the horizontal midline, which can be utilized to differentiate between glaucoma and normal subjects. Sensitivity and specificity of the mfVEP test showed very promising results and correlated with other anatomical changes in glaucoma field loss.

Evaluation of Hemifield Sector Analysis Protocol in Multifocal Visual Evoked Potential Objective Perimetry for the Diagnosis and Early Detection of Glaucomatous Field Defects

PubMed Central

Mousa, Mohammad F.; Cubbidge, Robert P.; Al-Mansouri, Fatima

2014-01-01

Purpose Multifocal visual evoked potential (mfVEP) is a newly introduced method used for objective visual field assessment. Several analysis protocols have been tested to identify early visual field losses in glaucoma patients using the mfVEP technique, some were successful in detection of field defects, which were comparable to the standard automated perimetry (SAP) visual field assessment, and others were not very informative and needed more adjustment and research work. In this study we implemented a novel analysis approach and evaluated its validity and whether it could be used effectively for early detection of visual field defects in glaucoma. Methods Three groups were tested in this study; normal controls (38 eyes), glaucoma patients (36 eyes) and glaucoma suspect patients (38 eyes). All subjects had a two standard Humphrey field analyzer (HFA) test 24-2 and a single mfVEP test undertaken in one session. Analysis of the mfVEP results was done using the new analysis protocol; the hemifield sector analysis (HSA) protocol. Analysis of the HFA was done using the standard grading system. Results Analysis of mfVEP results showed that there was a statistically significant difference between the three groups in the mean signal to noise ratio (ANOVA test, p < 0.001 with a 95% confidence interval). The difference between superior and inferior hemispheres in all subjects were statistically significant in the glaucoma patient group in all 11 sectors (t-test, p < 0.001), partially significant in 5 / 11 (t-test, p < 0.01), and no statistical difference in most sectors of the normal group (1 / 11 sectors was significant, t-test, p < 0.9). Sensitivity and specificity of the HSA protocol in detecting glaucoma was 97% and 86%, respectively, and for glaucoma suspect patients the values were 89% and 79%, respectively. Conclusions The new HSA protocol used in the mfVEP testing can be applied to detect glaucomatous visual field defects in both glaucoma and glaucoma suspect patients. Using this protocol can provide information about focal visual field differences across the horizontal midline, which can be utilized to differentiate between glaucoma and normal subjects. Sensitivity and specificity of the mfVEP test showed very promising results and correlated with other anatomical changes in glaucoma field loss. PMID:24511212

Making the Hubble Space Telescope servicing mission safe

NASA Technical Reports Server (NTRS)

Bahr, N. J.; Depalo, S. V.

1992-01-01

The implementation of the HST system safety program is detailed. Numerous safety analyses are conducted through various phases of design, test, and fabrication, and results are presented to NASA management for discussion during dedicated safety reviews. Attention is given to the system safety assessment and risk analysis methodologies used, i.e., hazard analysis, fault tree analysis, and failure modes and effects analysis, and to how they are coupled with engineering and test analysis for a 'synergistic picture' of the system. Some preliminary safety analysis results, showing the relationship between hazard identification, control or abatement, and finally control verification, are presented as examples of this safety process.

Airfoil Vibration Dampers program

NASA Technical Reports Server (NTRS)

Cook, Robert M.

1991-01-01

The Airfoil Vibration Damper program has consisted of an analysis phase and a testing phase. During the analysis phase, a state-of-the-art computer code was developed, which can be used to guide designers in the placement and sizing of friction dampers. The use of this computer code was demonstrated by performing representative analyses on turbine blades from the High Pressure Oxidizer Turbopump (HPOTP) and High Pressure Fuel Turbopump (HPFTP) of the Space Shuttle Main Engine (SSME). The testing phase of the program consisted of performing friction damping tests on two different cantilever beams. Data from these tests provided an empirical check on the accuracy of the computer code developed in the analysis phase. Results of the analysis and testing showed that the computer code can accurately predict the performance of friction dampers. In addition, a valuable set of friction damping data was generated, which can be used to aid in the design of friction dampers, as well as provide benchmark test cases for future code developers.

Correlation of Gerkin, Queen's College, George, and Jackson methods in estimating maximal oxygen consumption.

PubMed

Heydari, Payam; Varmazyar, Sakineh; Variani, Ali Safari; Hashemi, Fariba; Ataei, Seyed Sajad

2017-10-01

Test of maximal oxygen consumption is the gold standard for measuring cardio-pulmonary fitness. This study aimed to determine correlation of Gerkin, Queen's College, George, and Jackson methods in estimating maximal oxygen consumption, and demographic factors affecting maximal oxygen consumption. This descriptive cross-sectional study was conducted in a census of medical emergency students (n=57) in Qazvin University of Medical Sciences in 2016. The subjects firstly completed the General Health Questionnaire (PAR-Q) and demographic characteristics. Then eligible subjects were assessed using exercise tests of Gerkin treadmill, Queen's College steps and non-exercise George, and Jackson. Data analysis was carried out using independent t-test, one way analysis of variance and Pearson correlation in the SPSS software. The mean age of participants was 21.69±4.99 years. The mean of maximal oxygen consumption using Gerkin, Queen's College, George, and Jackson tests was 4.17, 3.36, 3.64, 3.63 liters per minute, respectively. Pearson statistical test showed a significant correlation among fours tests. George and Jackson tests had the greatest correlation (r=0.85, p>0.001). Results of tests of one-way analysis of variance and t-test showed a significant relationship between independent variable of weight and height in four tests, and dependent variable of maximal oxygen consumption. Also, there was a significant relationship between variable of body mass index in two tests of Gerkin and Queen's College and variable of exercise hours per week with the George and Jackson tests (p>0.001). Given the obtained correlation, these tests have the potential to replace each other as necessary, so that the non-exercise Jackson test can be used instead of the Gerkin test.

The contribution of aromatic components in Katsuobushi to preference formation and reinforcement effect.

PubMed

Amitsuka, Takahiko; Okamura, Maya; Mukuta, Kei; Shiibashi, Hiroko; Haraguchi, Kenji; Saito, Tsukasa; Inoue, Kazuo; Fushiki, Tohru

2017-08-01

Katsuodashi, a dried bonito broth, is very basic and indispensable in Japanese cuisine and contains taste-exhibiting components and unique aroma. We previously reported that its unique aroma contributes to the preference and reinforcement effect associated with dried bonito. This study aims to elucidate the contribution of aromatic components in Katsuobushi to preference formation and reinforcement effect. Volatile components obtained from dried bonito were fractionated and the fractions were subjected to two-bottle choice test. The fractionation test suggested that the component responsible for the preference is not one but comprises multiple components. In the GC-MS analysis/reconstruction test, solution with aromatic flavor narrowed down to 125 compounds had preference, and also had reinforcement effect. Moreover, GC-MS-olfactometry analysis narrowed down the candidate components to 28 out of 125. Mice showed preference for the test solution with aromatic flavor reconstructed with 28 components but did not show reinforcement behavior.

Student Background, School Climate, School Disorder, and Student Achievement: An Empirical Study of New York City's Middle Schools

ERIC Educational Resources Information Center

Chen, Greg; Weikart, Lynne A.

2008-01-01

This study develops and tests a school disorder and student achievement model based upon the school climate framework. The model was fitted to 212 New York City middle schools using the Structural Equations Modeling Analysis method. The analysis shows that the model fits the data well based upon test statistics and goodness of fit indices. The…

The Development of Extraversion and Ability: Analysis of Data from a Large-Scale Longitudinal Study of Children Tested at 10-11 and 14-15 Years.

ERIC Educational Resources Information Center

Anthony, W. S.

1983-01-01

Results of analysis of correlations collected by Cookson, following Eysenck and Cookson's study of personality and ability in young people, confirm the finding from previous Cattellian test data that the more intelligent children decline in relative extraversion scores and cast doubt on Eysenck's suggestion that introverts gradually show higher…

Reevaluating excess success in psychological science.

PubMed

van Boxtel, Jeroen J A; Koch, Christof

2016-10-01

Francis (Psychonomic Bulletin Review, 21, 1180-1187, 2014) recently claimed that 82 % of articles with four or more experiments published in Psychological Science between 2009 and 2012 cannot be trusted. We critique Francis' analysis and point out the dependence of his approach on including the appropriate experiments and significance tests. We focus on one of the articles (van Boxtel & Koch, in Psychological Science, 23(4), 410-418, 2012) flagged by Francis and show that the inappropriate inclusion of experiments and tests have led Francis to mistakenly flag this article. We found that decisions about whether to include certain tests potentially affect 34 of the 44 articles analyzed by Francis. We further performed p-curve analyses on the articles discussed in Francis' analysis. We found that 9 of 44 studies showed significant evidential value, 11 studies showed insufficient evidential value, and 1 study showed evidence of p-hacking. Our reevaluation is important, because some researchers may have gained the false impression that none of the quoted articles in Psychological Science can be trusted (as stated by Francis). The analysis by Francis is most likely insufficient to warrant this conclusion for some articles and certainly is insufficient with respect to the study by van Boxtel and Koch (Psychological Science, 23, 410-418, 2012).

Image analysis to evaluate the browning degree of banana (Musa spp.) peel.

PubMed

Cho, Jeong-Seok; Lee, Hyeon-Jeong; Park, Jung-Hoon; Sung, Jun-Hyung; Choi, Ji-Young; Moon, Kwang-Deog

2016-03-01

Image analysis was applied to examine banana peel browning. The banana samples were divided into 3 treatment groups: no treatment and normal packaging (Cont); CO2 gas exchange packaging (CO); normal packaging with an ethylene generator (ET). We confirmed that the browning of banana peels developed more quickly in the CO group than the other groups based on sensory test and enzyme assay. The G (green) and CIE L(∗), a(∗), and b(∗) values obtained from the image analysis sharply increased or decreased in the CO group. And these colour values showed high correlation coefficients (>0.9) with the sensory test results. CIE L(∗)a(∗)b(∗) values using a colorimeter also showed high correlation coefficients but comparatively lower than those of image analysis. Based on this analysis, browning of the banana occurred more quickly for CO2 gas exchange packaging, and image analysis can be used to evaluate the browning of banana peels. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effectiveness of problem-based learning on students’ problem solving ability in vector analysis course

NASA Astrophysics Data System (ADS)

Mushlihuddin, R.; Nurafifah; Irvan

2018-01-01

The student’s low ability in mathematics problem solving proved to the less effective of a learning process in the classroom. Effective learning was a learning that affects student’s math skills, one of which is problem-solving abilities. Problem-solving capability consisted of several stages: understanding the problem, planning the settlement, solving the problem as planned, re-examining the procedure and the outcome. The purpose of this research was to know: (1) was there any influence of PBL model in improving ability Problem solving of student math in a subject of vector analysis?; (2) was the PBL model effective in improving students’ mathematical problem-solving skills in vector analysis courses? This research was a quasi-experiment research. The data analysis techniques performed from the test stages of data description, a prerequisite test is the normality test, and hypothesis test using the ANCOVA test and Gain test. The results showed that: (1) there was an influence of PBL model in improving students’ math problem-solving abilities in vector analysis courses; (2) the PBL model was effective in improving students’ problem-solving skills in vector analysis courses with a medium category.

Analysis and test of low profile aluminum aerospace tank dome

NASA Astrophysics Data System (ADS)

Ahmed, R.; Wilhelm, J. M.

1993-12-01

In order to increase the structural performance of cryogenic tanks, the aerospace industry is beginning to employ low-profile bulkheads in new generation launch vehicle designs. This report details the analysis and test of one such dome made from 2219 aluminum. Such domes have two potential failure modes under internal pressure, general tensile failure and hoop compression buckling (in regions near the equator). The test determined the buckling load and ultimate tensile load of the hardware and showed that both compared well with the analysis predictions. This effort was conducted under the auspices of NASA and the General Dynamics Cryogenic Tank Technology Program (CTTP).

Analysis and test of low profile aluminum aerospace tank dome

NASA Technical Reports Server (NTRS)

Ahmed, R.; Wilhelm, J. M.

1993-01-01

In order to increase the structural performance of cryogenic tanks, the aerospace industry is beginning to employ low-profile bulkheads in new generation launch vehicle designs. This report details the analysis and test of one such dome made from 2219 aluminum. Such domes have two potential failure modes under internal pressure, general tensile failure and hoop compression buckling (in regions near the equator). The test determined the buckling load and ultimate tensile load of the hardware and showed that both compared well with the analysis predictions. This effort was conducted under the auspices of NASA and the General Dynamics Cryogenic Tank Technology Program (CTTP).

Blade loss transient dynamic analysis of turbomachinery

NASA Technical Reports Server (NTRS)

Stallone, M. J.; Gallardo, V.; Storace, A. F.; Bach, L. J.; Black, G.; Gaffney, E. F.

1982-01-01

This paper reports on work completed to develop an analytical method for predicting the transient non-linear response of a complete aircraft engine system due to the loss of a fan blade, and to validate the analysis by comparing the results against actual blade loss test data. The solution, which is based on the component element method, accounts for rotor-to-casing rubs, high damping and rapid deceleration rates associated with the blade loss event. A comparison of test results and predicted response show good agreement except for an initial overshoot spike not observed in test. The method is effective for analysis of large systems.

Heparin Reversal After Cardiopulmonary Bypass: Are Point-of-Care Coagulation Tests Interchangeable?

PubMed

Willems, Ariane; Savan, Veaceslav; Faraoni, David; De Ville, Andrée; Rozen, Laurence; Demulder, Anne; Van der Linden, Philippe

2016-10-01

Protamine is used to neutralize heparin after patient separation from cardiopulmonary bypass (CPB). Different bedside tests are used to monitor the adequacy of heparin neutralization. For this study, the interchangeability of the activated coagulation time (ACT) and thromboelastometry (ROTEM; Tem Innovations GmbH, Basel, Switzerland) clotting time (CT) ratios in children undergoing cardiac surgery was assessed. Single-center, retrospective, cohort study between September 2010 and January 2012. University children's hospital. The study comprised children 0 to 16 years old undergoing elective cardiac surgery with CPB. Exclusion criteria were preoperative coagulopathy, Jehovah's witnesses, and children in a moribund condition (American Society of Anesthesiologists score 5). None. After heparin neutralization with protamine, the ratio between ACT, with and without heparinase, and the CT measured with INTEM/HEPTEM (intrinsic test activated with ellagic acid was performed without heparinase [INTEM] and with heparinase [HEPTEM]) using tests of ROTEM were calculated. Agreement was evaluated using Cohen's kappa statistics, Passing-Bablok regression, and Bland-Altman analysis. Among the 173 patients included for analysis, agreement between both tests showed a Cohen's kappa statistic of 0.06 (95% CI: -0.02 to 0.14; p = 0.22). Bland-Altman analysis showed a bias of 0.01, with a standard deviation of 0.13, and limits of agreement between -0.24 and 0.26. Passing-Bablok regression showed a systematic difference of 0.40 (95% CI: 0.16-0.59) and a proportional difference of 0.61 (95% CI: 0.42-0.86). The residual standard deviation was 0.11 (95% CI: -0.22 to 0.22), and the test for linearity showed p = 0.10. ACT, with or without heparinase, and the INTEM/HEPTEM CT ratios are not interchangeable to evaluate heparin reversal after pediatric patient separation from CPB. Therefore, the results of these tests should be corroborated with the absence/presence of bleeding and integrated into center-specific treatment algorithms. Copyright © 2016 Elsevier Inc. All rights reserved.

Analysis of possibilities of waste heat recovery in off-road vehicles

NASA Astrophysics Data System (ADS)

Wojciechowski, K. T.; Zybala, R.; Leszczynski, J.; Nieroda, P.; Schmidt, M.; Merkisz, J.; Lijewski, P.; Fuc, P.

2012-06-01

The paper presents the preliminary results of the waste heat recovery investigations for an agricultural tractor engine (7.4 dm3) and excavator engine (7.2 dm3) in real operating conditions. The temperature of exhaust gases and exhaust mass flow rate has been measured by precise portable exhaust emissions analyzer SEMTECH DS (SENSORS Inc.). The analysis shows that engines of tested vehicles operate approximately at constant speed and load. The average temperature of exhaust gases is in the range from 300 to 400 °C for maximum gas mass flows of 1100 kg/h and 1400 kg/h for tractor and excavator engine respectively. Preliminary tests show that application of TEGs in tested off-road vehicles offers much more beneficial conditions for waste heat recovery than in case of automotive engines.

Data on the no-load performance analysis of a tomato postharvest storage system.

PubMed

Ayomide, Orhewere B; Ajayi, Oluseyi O; Banjo, Solomon O; Ajayi, Adesola A

2017-08-01

In this present investigation, an original and detailed empirical data on the transfer of heat in a tomato postharvest storage system was presented. No-load tests were performed for a period of 96 h. The heat distribution at different locations, namely the top, middle and bottom of the system was acquired, at a time interval of 30 min for the test period. The humidity inside the system was taken into consideration. Thus, No-load tests with or without introduction of humidity were carried out and data showing the effect of a rise in humidity level, on temperature distribution were acquired. The temperatures at the external mechanical cooling components were acquired and could be used for showing the performance analysis of the storage system.

Structural Analysis and Testing of an Erectable Truss for Precision Segmented Reflector Application

NASA Technical Reports Server (NTRS)

Collins, Timothy J.; Fichter, W. B.; Adams, Richard R.; Javeed, Mehzad

1995-01-01

This paper describes analysis and test results obtained at Langley Research Center (LaRC) on a doubly curved testbed support truss for precision reflector applications. Descriptions of test procedures and experimental results that expand upon previous investigations are presented. A brief description of the truss is given, and finite-element-analysis models are described. Static-load and vibration test procedures are discussed, and experimental results are shown to be repeatable and in generally good agreement with linear finite-element predictions. Truss structural performance (as determined by static deflection and vibration testing) is shown to be predictable and very close to linear. Vibration test results presented herein confirm that an anomalous mode observed during initial testing was due to the flexibility of the truss support system. Photogrammetric surveys with two 131-in. reference scales show that the root-mean-square (rms) truss-surface accuracy is about 0.0025 in. Photogrammetric measurements also indicate that the truss coefficient of thermal expansion (CTE) is in good agreement with that predicted by analysis. A detailed description of the photogrammetric procedures is included as an appendix.

Ceramic regenerator systems development program

NASA Technical Reports Server (NTRS)

Cook, J. A.; Fucinari, C. A.; Lingscheit, J. N.; Rahnke, C. J.; Rao, V. D.

1978-01-01

Ceramic regenerator cores are considered that can be used in passenger car gas turbine engines, Stirling engines, and industrial/truck gas turbine engines. Improved materials and design concepts aimed at reducing or eliminating chemical attack were placed on durability tests/in industrial gas turbine engines. A regenerator core made from aluminum silicate shows minimal evidence of chemical attack damage after 7804 hours of engine test at 800 C and another showed little distress after 4983 hours at 982 C. The results obtained in ceramic material screening tests, aerothermodynamic performance tests, stress analysis, cost studies, and material specifications are also included.

A comparison of the MeltPro® HPV Test with the Cobas® HPV Test for detecting and genotyping 14 high-risk human papillomavirus types.

PubMed

Tang, Zhiteng; Xu, Ye; Song, Najie; Zou, Dongqing; Liao, Yiqun; Li, Qingge; Pan, Chao

2018-03-01

The clinical performance of the newly developed MeltPro ® HPV Test, based on multicolor melting curve analysis, was evaluated and compared with the commercially available Cobas ® HPV Test for detection of HPV and genotyping of HPV-16 and HPV-18. A total of 1647 cervical samples were analyzed with both tests. The agreement values were 96.2% for HPV detection, 99.6% for HPV-16 identification, and 99.7% for HPV-18 identification. All genotyping results from MeltPro ® HPV Test showed that HPV-52, HPV-58, and HPV-16 were the most common types in this study. Intra-laboratory reproducibility studies showed 97.8% agreement while inter-laboratory reproducibility studies showed 96.9% agreement for the MeltPro ® HPV Test. The MeltPro ® HPV Test and Cobas ® HPV Test are highly correlative and are useful for monitoring HPV infection.

Differential Canard deflection for generation of yawing moment on the X-31 with and without the vertical tail. M.S. Thesis - George Washington Univ.

NASA Technical Reports Server (NTRS)

Whiting, Matthew Robert

1996-01-01

The feasibility of augmenting the available yaw control power on the X-31 through differential deflection of the canard surfaces was studied as well as the possibility of using differential canard control to stabilize the X-31 with its vertical tail removed. Wind-tunnel tests and the results of departure criteria and linear analysis showed the destabilizing effect of the reduction of the vertical tail on the X-31. Wind-tunnel testing also showed that differential canard deflection was capable of generating yawing moments of roughly the same magnitude as the thrust vectoring vanes currently in place on the X-31 in the post-stall regime. Analysis showed that the X-31 has sufficient aileron roll control power that with the addition of differential canard as a yaw controller, the wind-axis roll accelerations will remain limited by yaw control authority. It was demonstrated, however, that pitch authority may actually limit the maximum roll rate which can be sustained. A drop model flight test demonstrated that coordinated, wind axis rolls could be performed with roll rates as high as 50 deg/sec (full scale equivalent) at 50 deg angle of attack. Another drop model test was conducted to assess the effect of vertical tail reduction, and an analysis of using differential canard deflection to stabilize the tailless X-31 was performed. The results of six-degree-of-freedom, non-linear simulation tests were correlated with the drop model flights. Simulation studies then showed that the tailless X-31 could be controlled at angles of attack at or above 20 deg using differential canard as the only yaw controller.

A structural review of foliar glands in Passiflora L. (Passifloraceae)

PubMed Central

da Costa Silva, Delmira; Flavia de Albuquerque Melo-de-Pinna, Gladys

2017-01-01

Extrafloral glands in Passifloraceae species have aroused the interest of many researchers because of their wide morphological diversity. The present work analyzed the foliar glands on 34 species of Passiflora from samples containing glands in the petiole and foliar blade fixed in 50% solution of formaldehyde-ethanol-acetic acid and stored in a 70% ethanol solution. For anatomical analyses, part of the material was embedded in Paraplast, longitudinally sectioned and double stained with safranin and astra blue. Scanning electron microscopy analysis was also carried out. To analyze the presence of sugars in the secretion of foliar glands, a glucose strip test was used. Based on the results of morphological, anatomical and glucose strip tests, the foliar secretory glands in Passiflora can be grouped into two categories: Type I glands, defined as nectaries, can be elevated or flattened, and can have a sugar content high enough to be detected by the glucose strip test analysis. Type II glands are elevated and did not show a positive reaction to the glucose strip test. From an anatomical viewpoint, glands characterized as extrafloral nectaries show a multistratified secretory epidermis, typically followed by two flat layers of nectariferous parenchyma with dense content. Internal to these layers, vascular bundles are immersed in the subsecretory parenchyma and terminate in phloem cells. On the other hand, type II glands show a single layer of elongated secretory epidermal cells. Internal to this single layer, parenchyma and vascular tissue with both phloem and xylem elements can be observed. The analyzed species show a wide diversity of gland shape and distribution, and the combined analysis of morphology, anatomy and preliminary tests for the presence of glucose in the exudate in different Passiflora subgenera suggests the occurrence of two categories of glands: nectaries and resin glands. PMID:29136029

Studies of thermionic materials for space power applications

NASA Technical Reports Server (NTRS)

1971-01-01

Service life tests of LC-8 and LC-9 carbide-fueled thermionic converters are discussed. Post operational tests of the converters to show emitter diametric change, microstructures of cladding and fuel, and analysis of fuel composition are described. The fabrication and performance of high temperature thermocouples used in the test procedures are included.

Knox's Cube Imitation Test: A Historical Review and an Experimental Analysis

ERIC Educational Resources Information Center

Richardson, John T. E.

2005-01-01

The cube imitation test was developed by Knox (1913) as a nonverbal test of intelligence. Many variants show satisfactory reliability, but performance is correlated both with Verbal IQ and with Performance IQ. Performance is impaired by cerebral lesions but unrelated to the side of lesion. Examinees describe both verbal and visuospatial…

Development of HAN-based Liquid Propellant Thruster

NASA Astrophysics Data System (ADS)

Hisatsune, K.; Izumi, J.; Tsutaya, H.; Furukawa, K.

2004-10-01

Many of propellants that are applied to the conventional spacecraft propulsion system are toxic propellants. Because of its toxicity, considering the environmental pollution or safety on handling, it will be necessary to apply the "green" propellant to the spacecraft propulsion system. The purpose of this study is to apply HAN based liquid propellant (LP1846) to mono propellant thruster. Compared to the hydrazine that is used in conventional mono propellant thruster, HAN based propellant is not only lower toxic but also can obtain higher specific impulse. Moreover, HAN based propellant can be decomposed by the catalyst. It means there are the possibility of applying to the mono propellant thruster that can leads to the high reliability of the propulsion system.[1],[2] However, there are two technical subjects, to apply HAN based propellant to the mono propellant thruster. One is the high combustion temperature. The catalyst will be damaged under high temperature condition. The other is the low catalytic activity. It is the serious problem on application of HAN based propellant to the mono propellant thruster that is used for attitude control of spacecraft. To improve the catalytic activity of HAN based propellant, it is necessary to screen the best catalyst for HAN based propellant. The adsorption analysis is conducted by Monte Carlo Simulation to screen the catalyst metal for HAN and TEAN. The result of analysis shows the Iridium is the best catalyst metal for HAN and TEAN. Iridium is the catalyst metal that is used at conventional mono propellant thruster catalyst Shell405. Then, to confirm the result of analysis, the reaction test about catalyst is conducted. The result of this test is the same as the result of adsorption analysis. That means the adsorption analysis is effective in screening the catalyst metal. At the evaluating test, the various types of carrier of catalyst are also compared to Shell 405 to improve catalytic activity. The test result shows the inorganic porous media is superior to Shell405 in catalytic activity. Next, the catalyst life with HAN based propellant (LP1846) is evaluated. The Shell405 and inorganic porous media catalyst are compared at the life test. The test result shows the inorganic porous media catalyst is superior to Shell405 in catalyst life. In this paper, the detail of the result of adsorption analysis and evaluating test are reported.

Item response theory analysis of the mechanics baseline test

NASA Astrophysics Data System (ADS)

Cardamone, Caroline N.; Abbott, Jonathan E.; Rayyan, Saif; Seaton, Daniel T.; Pawl, Andrew; Pritchard, David E.

2012-02-01

Item response theory is useful in both the development and evaluation of assessments and in computing standardized measures of student performance. In item response theory, individual parameters (difficulty, discrimination) for each item or question are fit by item response models. These parameters provide a means for evaluating a test and offer a better measure of student skill than a raw test score, because each skill calculation considers not only the number of questions answered correctly, but the individual properties of all questions answered. Here, we present the results from an analysis of the Mechanics Baseline Test given at MIT during 2005-2010. Using the item parameters, we identify questions on the Mechanics Baseline Test that are not effective in discriminating between MIT students of different abilities. We show that a limited subset of the highest quality questions on the Mechanics Baseline Test returns accurate measures of student skill. We compare student skills as determined by item response theory to the more traditional measurement of the raw score and show that a comparable measure of learning gain can be computed.

Assessment of Metronidazole Susceptibility in Helicobacter pylori: Statistical Validation and Error Rate Analysis of Breakpoints Determined by the Disk Diffusion Test

PubMed Central

Chaves, Sandra; Gadanho, Mário; Tenreiro, Rogério; Cabrita, José

1999-01-01

Metronidazole susceptibility of 100 Helicobacter pylori strains was assessed by determining the inhibition zone diameters by disk diffusion test and the MICs by agar dilution and PDM Epsilometer test (E test). Linear regression analysis was performed, allowing the definition of significant linear relations, and revealed correlations of disk diffusion results with both E-test and agar dilution results (r2 = 0.88 and 0.81, respectively). No significant differences (P = 0.84) were found between MICs defined by E test and those defined by agar dilution, taken as a standard. Reproducibility comparison between E-test and disk diffusion tests showed that they are equivalent and with good precision. Two interpretative susceptibility schemes (with or without an intermediate class) were compared by an interpretative error rate analysis method. The susceptibility classification scheme that included the intermediate category was retained, and breakpoints were assessed for diffusion assay with 5-μg metronidazole disks. Strains with inhibition zone diameters less than 16 mm were defined as resistant (MIC > 8 μg/ml), those with zone diameters equal to or greater than 16 mm but less than 21 mm were considered intermediate (4 μg/ml < MIC ≤ 8 μg/ml), and those with zone diameters of 21 mm or greater were regarded as susceptible (MIC ≤ 4 μg/ml). Error rate analysis applied to this classification scheme showed occurrence frequencies of 1% for major errors and 7% for minor errors, when the results were compared to those obtained by agar dilution. No very major errors were detected, suggesting that disk diffusion might be a good alternative for determining the metronidazole sensitivity of H. pylori strains. PMID:10203543

The effect of physics-based scientific learning on the improvement of the student’s critical thinking skills

NASA Astrophysics Data System (ADS)

Zaidah, A.; Sukarmin; Sunarno, W.

2018-04-01

This study aimed to determine the influence of a physics-based scientific learning to increase student’s critical thinking skill. This type of this research was quantitative research with taking the conclusion through statistical analysis. This research was carried out in MA (Senior High School) Mu'allimat NW Pancor in the second semester in the academic year of 2016/2017 with all students of XI class. The sampling is done by using technique purposive sampling where the class was taken from XI 6 class. Based on the result of descriptive analysis, it was obtained an average pre-test score of 49.17 and an average post-test score of 82.43. Also, the results showed that the average score was gained of 0.67 with a medium category. Based on the inferential analysis showed the value of t = 22.559 while the ttable in significance level of 5% was 2.04. Thus, t > the ttable from Ha is accepted. Therefore, the pre-test and posttest were different significantly when the students used scientific-based learning. The result showed that a physics-based scientific learning has influenced to increase the student’s critical thinking skill.

Sensory evaluation of locally-grown fruit purees and inulin fibre on probiotic yogurt in Mwanza, Tanzania and the Microbial Analysis of Probiotic Yogurt Fortified with Moringa oleifera.

PubMed

Hekmat, Sharareh; Morgan, Kathryn; Soltani, Mohammad; Gough, Robert

2015-03-01

The purpose of this study was to establish new food products that increase the nutritional value and health benefits of the probiotic yogurt currently used in the Western Heads East (WHE) Project in Mwanza, Tanzania. The probiotic yogurt has established health benefits, and product development through fortification must not adversely affect the acceptability of yogurt or the viability of the probiotics. Both sensory testing and microbial analysis testing were conducted. The products tested were yogurt fortified with locally-grown fruit purees with inulin and Moringa oleifera. The results of the sensory evaluation showed that all yogurts were not rated significantly different from the control, except for appearance. The avocado puree without inulin rated significantly lower in all categories. The microbial analysis showed that Moringa oleifera did not negatively affect the growth of Lactobacillus rhamnosus GR-1 in MRS, milk or yogurt, although a significant decrease was found after 5 weeks of storage at 4 (o)C.

Mechanical performance and thermal stability of glass fiber reinforced silica aerogel composites based on co-precursor method by freeze drying

NASA Astrophysics Data System (ADS)

Zhou, Ting; Cheng, Xudong; Pan, Yuelei; Li, Congcong; Gong, Lunlun; Zhang, Heping

2018-04-01

In order to maintain the integrity, glass fiber (GF) reinforced silica aerogel composites were synthesized using methltrimethoxysilane (MTMS) and water glass co-precursor by freeze drying method. The composites were characterized by scanning electron microscopy, Brunauer-Emmett-Teller analysis, uniaxial compressive test, three-point bending test, thermal conductivity analysis, contact angle test, TG-DSC analysis. It was found that the molar ratio of MTMS/water glass could significantly affect the properties of composites. The bulk density and thermal conductivity first decreased and then increased with the increasing molar ratio. The composites showed remarkable mechanical strength and flexibility compared with pure silica aerogel. Moreover, when the molar ratio is 1.8, the composites showed high specific surface area (870.9 m2/g), high contact angle (150°), great thermal stability (560 °C) and low thermal conductivity (0.0248 W/m·K). These outstanding properties indicate that GF/aerogels have broad prospects in the field of thermal insulation.

Methodenvergleich zur Bestimmung der hydraulischen Durchlässigkeit

NASA Astrophysics Data System (ADS)

Storz, Katharina; Steger, Hagen; Wagner, Valentin; Bayer, Peter; Blum, Philipp

2017-06-01

Knowing the hydraulic conductivity (K) is a precondition for understanding groundwater flow processes in the subsurface. Numerous laboratory and field methods for the determination of hydraulic conductivity exist, which can lead to significantly different results. In order to quantify the variability of these various methods, the hydraulic conductivity was examined for an industrial silica sand (Dorsilit) using four different methods: (1) grain-size analysis, (2) Kozeny-Carman approach, (3) permeameter tests and (4) flow rate experiments in large-scale tank experiments. Due to the large volume of the artificially built aquifer, the tank experiment results are assumed to be the most representative. Hydraulic conductivity values derived from permeameter tests show only minor deviation, while results of the empirically evaluated grain-size analysis are about one magnitude higher and show great variances. The latter was confirmed by the analysis of several methods for the determination of K-values found in the literature, thus we generally question the suitability of grain-size analyses and strongly recommend the use of permeameter tests.

What Do Test Score Really Mean? A Latent Class Analysis of Danish Test Score Performance

ERIC Educational Resources Information Center

McIntosh, James; Munk, Martin D.

2014-01-01

Latent class Poisson count models are used to analyse a sample of Danish test score results from a cohort of individuals born in 1954-1955, tested in 1968, and followed until 2011. The procedure takes account of unobservable effects as well as excessive zeros in the data. We show that the test scores measure manifest or measured ability as it has…

Cluster analysis of cognitive performance in elderly and demented subjects.

PubMed

Giaquinto, S; Nolfe, G; Calvani, M

1985-06-01

48 elderly normals, 14 demented subjects and 76 young controls were tested for basic cognitive functions. All the tests were quantified and could therefore be subjected to statistical analysis. The results show a difference in the speed of information processing and in memory load between the young controls and elderly normals but the age groups differed in quantitative terms only. Cluster analysis showed that the elderly and the demented formed two distinctly separate groups at the qualitative level, the basic cognitive processes being damaged in the demented group. Age thus appears to be only a risk factor for dementia and not its cause. It is concluded that batteries based on precise and measurable tasks are the most appropriate not only for the study of dementia but for rehabilitation purposes too.

Thermal Performance Testing of EMU and CSAFE Liquid Cooling Garments

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Bue, Grant; Hakam, Mark; Radford, Tamara

2013-01-01

Future exploration missions require the development of a new liquid cooling garment (LCG) that offers greater system reliability, is more comfortable, and maximizes thermal performance. To inform the development of a future LCG a thermal performance test was conducted to evaluate three factors: (1) the effect of the thermal comfort undergarment (TCU) on tactile and thermal comfort, (2) the comparable thermal performance of an CSAFE developed engineering evaluation unit (EEU) LCG, which uses a commercial-off-the-shelf (COTS) wicking garment as the base, and (3) the performance of a torso or upper body only LCG configuration to evaluate a proposed auxiliary loop configuration. To evaluate the thermal performance of each configuration a metabolic suit test was conducted, utilizing suited subjects to generate metabolic heat by walking on a treadmill at various speeds. Three (3) test subjects of similar height and weight produced a metabolic load for five tests by either resting (300-600 BTU/hr), walking at a slow pace (1200 BTU/hr), and walking at a brisk pace (2200 BTU/hr). During the test, data was collected that would allow us to track the heat transfer to the LCG and ventilation system to determine the thermal performance of the LCG configurations. Four different test configurations were tested, with one configuration tested twice. The test results show that the CSAFE EEU LCG and EMU LCG had comparable performance. The testing also showed that an auxiliary loop LCG, sized similarly to the shirt-only configuration, should provide adequate cooling for contingency scenarios. Finally, the testing showed the previous analysis that assumed a UA deterioration from the TCU was too conservative and the TCU may prove to be acceptable for future development with additional analysis and testing.

A decision impact, decision conflict and economic assessment of routine Oncotype DX testing of 146 women with node-negative or pNImi, ER-positive breast cancer in the UK

PubMed Central

Holt, S; Bertelli, G; Humphreys, I; Valentine, W; Durrani, S; Pudney, D; Rolles, M; Moe, M; Khawaja, S; Sharaiha, Y; Brinkworth, E; Whelan, S; Jones, S; Bennett, H; Phillips, C J

2013-01-01

Background: Tumour gene expression analysis is useful in predicting adjuvant chemotherapy benefit in early breast cancer patients. This study aims to examine the implications of routine Oncotype DX testing in the UK. Methods: Women with oestrogen receptor positive (ER+), pNO or pN1mi breast cancer were assessed for adjuvant chemotherapy and subsequently offered Oncotype DX testing, with changes in chemotherapy decisions recorded. A subset of patients completed questionnaires about their uncertainties regarding chemotherapy decisions pre- and post-testing. All patients were asked to complete a diary of medical interactions over the next 6 months, from which economic data were extracted to model the cost-effectiveness of testing. Results: Oncotype DX testing resulted in changes in chemotherapy decisions in 38 of 142 (26.8%) women, with 26 of 57 (45.6%) spared chemotherapy and 12 of 85 (14.1%) requiring chemotherapy when not initially recommended (9.9% reduction overall). Decision conflict analysis showed that Oncotype DX testing increased patients' confidence in treatment decision making. Economic analysis showed that routine Oncotype DX testing costs £6232 per quality-adjusted life year gained. Conclusion: Oncotype DX decreased chemotherapy use and increased confidence in treatment decision making in patients with ER+ early-stage breast cancer. Based on these findings, Oncotype DX is cost-effective in the UK setting. PMID:23695023

Contribution to interplay between a delamination test and a sensory analysis of mid-range lipsticks.

PubMed

Richard, C; Tillé-Salmon, B; Mofid, Y

2016-02-01

Lipstick is currently one of the most sold products of cosmetics industry, and the competition between the various manufacturers is significant. Customers mainly seek products with high spreadability, especially long-lasting or long wear on the lips. Evaluation tests of cosmetics are usually performed by sensory analysis. This can then represent a considerable cost. The object of this study was to develop a fast and simple test of delamination (objective method with calibrated instruments) and to interplay the obtained results with those of a discriminative sensory analysis (subjective method) in order to show the relevance of the instrumental test. Three mid-range lipsticks were randomly chosen and were tested. They were made of compositions as described by the International Nomenclature of Cosmetic Ingredients (INCI). Instrumental characterization was performed by texture profile analysis and by a special delamination test. The sensory analysis was voluntarily conducted with an untrained panel as blind test to confirm or reverse the possible interplay. The two approaches or methods gave the same type of classification. The high-fat lipstick had the worst behaviour with the delamination test and the worst notation of the intensity of descriptors with the sensory analysis. There is a high correlation between the sensory analysis and the instrumental measurements in this study. The delamination test carried out should permit to quickly determine the lasting (screening test) and in consequence optimize the basic formula of lipsticks. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Wald Sequential Probability Ratio Test for Analysis of Orbital Conjunction Data

NASA Technical Reports Server (NTRS)

Carpenter, J. Russell; Markley, F. Landis; Gold, Dara

2013-01-01

We propose a Wald Sequential Probability Ratio Test for analysis of commonly available predictions associated with spacecraft conjunctions. Such predictions generally consist of a relative state and relative state error covariance at the time of closest approach, under the assumption that prediction errors are Gaussian. We show that under these circumstances, the likelihood ratio of the Wald test reduces to an especially simple form, involving the current best estimate of collision probability, and a similar estimate of collision probability that is based on prior assumptions about the likelihood of collision.

Criterion-Related Validity of the Distance- and Time-Based Walk/Run Field Tests for Estimating Cardiorespiratory Fitness: A Systematic Review and Meta-Analysis

PubMed Central

Mayorga-Vega, Daniel; Bocanegra-Parrilla, Raúl; Ornelas, Martha; Viciana, Jesús

2016-01-01

Objectives The main purpose of the present meta-analysis was to examine the criterion-related validity of the distance- and time-based walk/run tests for estimating cardiorespiratory fitness among apparently healthy children and adults. Materials and Methods Relevant studies were searched from seven electronic bibliographic databases up to August 2015 and through other sources. The Hunter-Schmidt’s psychometric meta-analysis approach was conducted to estimate the population criterion-related validity of the following walk/run tests: 5,000 m, 3 miles, 2 miles, 3,000 m, 1.5 miles, 1 mile, 1,000 m, ½ mile, 600 m, 600 yd, ¼ mile, 15 min, 12 min, 9 min, and 6 min. Results From the 123 included studies, a total of 200 correlation values were analyzed. The overall results showed that the criterion-related validity of the walk/run tests for estimating maximum oxygen uptake ranged from low to moderate (rp = 0.42–0.79), with the 1.5 mile (rp = 0.79, 0.73–0.85) and 12 min walk/run tests (rp = 0.78, 0.72–0.83) having the higher criterion-related validity for distance- and time-based field tests, respectively. The present meta-analysis also showed that sex, age and maximum oxygen uptake level do not seem to affect the criterion-related validity of the walk/run tests. Conclusions When the evaluation of an individual’s maximum oxygen uptake attained during a laboratory test is not feasible, the 1.5 mile and 12 min walk/run tests represent useful alternatives for estimating cardiorespiratory fitness. As in the assessment with any physical fitness field test, evaluators must be aware that the performance score of the walk/run field tests is simply an estimation and not a direct measure of cardiorespiratory fitness. PMID:26987118

USB environment measurements based on full-scale static engine ground tests

NASA Technical Reports Server (NTRS)

Sussman, M. B.; Harkonen, D. L.; Reed, J. B.

1976-01-01

Flow turning parameters, static pressures, surface temperatures, surface fluctuating pressures and acceleration levels were measured in the environment of a full-scale upper surface blowing (USB) propulsive lift test configuration. The test components included a flightworthy CF6-50D engine, nacelle, and USB flap assembly utilized in conjunction with ground verification testing of the USAF YC-14 Advanced Medium STOL Transport propulsion system. Results, based on a preliminary analysis of the data, generally show reasonable agreement with predicted levels based on model data. However, additional detailed analysis is required to confirm the preliminary evaluation, to help delineate certain discrepancies with model data, and to establish a basis for future flight test comparisons.

Face distinctiveness and delayed testing: differential effects on performance and confidence.

PubMed

Metzger, Mitchell M

2006-04-01

The author investigated the effect of delayed testing on participants' memory for distinctive and typical faces. Participants viewed distinctive and typical faces and were then tested for recognition immediately or after a delay of 3, 6, or 12 weeks. Consistent with prior research, analysis of measure of sensitivity (d') showed that participants performed better on distinctive rather than typical faces, and memory performance declined with longer retention intervals between study and testing. Furthermore, the superior performance on distinctive faces had vanished by the 12-week test. Contrary to d' data, however, an analysis of confidence scores indicated that participants were still significantly more confident on trials depicting distinctive faces, even with a 12-week delay between study and recognition testing.

The Use of Concept Map as a Consolidation Phase Based STAD to Enhance Students’ Comprehension about Environmental Pollution

NASA Astrophysics Data System (ADS)

Nugroho, O. F.; Chandra, D. T.; Sanjaya, Y.; Pendidikan Indonesia, Universitas

2017-02-01

The purpose of this study was to improve students’ concept comprehension using concept map as a consolidation phase based STAD. This study was conducted by randomized control group pretest-posttest. Data was collected by using an instrument test to evaluate the effect of concept map as a consolidation phase based STAD on students’understanding about environmental pollution. Data was analyzed using normalized gain (n-gain) and independent t-test. The n-gain analysis shows the increased of students’s understanding about environmental pollution at experimental group arehigher than at the control group. The result of this study showed that students’ comprehension at the experimental class (0,53) higher compared to the control group (0,23). Whilst the t-test analysis shows that there is a significant effect of mapping concept as a consolidation phase based STAD towards students’ concept comprehension. It can be concluded that the implementation of mapping concept based STAD may improve the students’s understanding on science concept.

Trend and change point analyses of annual precipitation in the Souss-Massa Region in Morocco during 1932-2010

NASA Astrophysics Data System (ADS)

Abahous, H.; Ronchail, J.; Sifeddine, A.; Kenny, L.; Bouchaou, L.

2017-11-01

In the context of an arid area such as Souss Massa Region, the availability of time series analysis of observed local data is vital to better characterize the regional rainfall configuration. In this paper, dataset of monthly precipitation collected from different local meteorological stations during 1932-2010, are quality controlled and analyzed to detect trend and change points. The temporal distribution of outliers shows an annual cycle and a decrease of their number since the 1980s. The results of the standard normal homogeneity test, penalized maximal t test, and Mann-Whitney-Pettit test show that 42% of the series are homogeneous. The analysis of annual precipitation in the region of Souss Massa during 1932-2010 shows wet conditions with a maximum between 1963 and 1965 followed by a decrease since 1973. The latter is identified as a statistically significant regional change point in Western High Atlas and Anti Atlas Mountains highlighting a decline in long-term average precipitation.

The Geoscience Concept Test: A New Assessment Tool Based on Student Misconceptions

NASA Astrophysics Data System (ADS)

Libarkin, J.; Anderson, S. W.; Boone, W. J.; Beilfuss, M.; Dahl, J.

2002-12-01

We developed and began pilot testing of an earth science assessment tool called the geoscience concept test (GCT). The GCT uses student misconceptions as distractors in a 30 item multiple-choice instrument. Student misconceptions were first assessed through the analysis of nearly 300 questionnaires administered in introductory geology courses at three institutions. Results from the questionnaires guided the development of an interview protocol that was used by four interviewers at four different institutions. Over 100 in-depth student interviews lasting from 0.5 to 1 hour probed topics related to the Earth's interior, geologic time, and the formation of Earth surface features such as mountains and volcanoes to better define misconceptions. Thematic content analysis of the interviews identified a number of widely held misconceptions, which were then incorporated into the GCT as multiple-choice distractors (wrong answers). For content validity, the initial GCT was reviewed by seven experts (3 geoscientists and 4 science educators) and revised before pilot testing. Approximately 100 introductory and non-science major college students from four institutions were assessed with the GCT pilot in the spring of 2002. Rasch model analysis of this data showed that students found the pilot test difficult, and the level of difficulty was consistent between the four institutions. Analysis of individual items showed that students had fewer misconceptions regarding the locations of earthquakes, and many misconceptions regarding the locations of volcanoes on the Earth's surface, suggesting a disconnect in their understanding of the role of plate tectonics in these phenomena. Analysis of the misfit statistic for each item showed that none of the questions misfit, although we dropped one question and modified the wording of another for clarity in the next round of piloting. A second round of piloting scheduled for the fall of 2002 includes nearly 3000 students from 34 institutions in 19 states.

Characterization of bioplastic based from cassava crisp home industrial waste incorporated with chitosan and liquid smoke

NASA Astrophysics Data System (ADS)

Fathanah, U.; Lubis, M. R.; Nasution, F.; Masyawi, M. S.

2018-03-01

Cassava peel (Manihot utilissima) is waste of agricultural result that is much potential as raw material of bioplastic making. This research focuses on bioplastic making from cassava peel. It aims to characterize the resulted bioplastic (mechanical and physical properties, SEM analysis, FTIR analysis and time test of bioplastic degradation). The bioplastic preparation takes place by mixing starch of cassava peel and chitosan (20, 30, 40 and 50% w/w), glycerol 30% w/w as plasticizer, and liquid smoke (0, 1 and 2 mL) as antimicrobial agent. The research result shows the highest value of tensile strength is 96.04 MPa, the highest elongation at break is 52.27%, and the value of water-resistant test is 22.68%. Morphology analysis by using SEM shows uneven surface and there is fracture in its cross-section. The analysis of functional group by FTIR shows the presence of functional groups of O–H (hydroxyl), N–H (amine), dan CH3–O (ether). The fastest complete degradation of bioplastic occurs in 45 days, and the longest occurs in 57 days.

Cognitive performance and psychosocial functioning in patients with bipolar disorder, unaffected siblings, and healthy controls.

PubMed

Vasconcelos-Moreno, Mirela P; Bücker, Joana; Bürke, Kelen P; Czepielewski, Leticia; Santos, Barbara T; Fijtman, Adam; Passos, Ives C; Kunz, Mauricio; Bonnín, Caterina Del Mar; Vieta, Eduard; Kapczinski, Flavio; Rosa, Adriane R; Kauer-Sant'Anna, Marcia

2016-01-01

To assess cognitive performance and psychosocial functioning in patients with bipolar disorder (BD), in unaffected siblings, and in healthy controls. Subjects were patients with BD (n=36), unaffected siblings (n=35), and healthy controls (n=44). Psychosocial functioning was accessed using the Functioning Assessment Short Test (FAST). A sub-group of patients with BD (n=21), unaffected siblings (n=14), and healthy controls (n=22) also underwent a battery of neuropsychological tests: California Verbal Learning Test (CVLT), Stroop Color and Word Test, and Wisconsin Card Sorting Test (WCST). Clinical and sociodemographic characteristics were analyzed using one-way analysis of variance or the chi-square test; multivariate analysis of covariance was used to examine differences in neuropsychological variables. Patients with BD showed higher FAST total scores (23.90±11.35) than healthy controls (5.86±5.47; p < 0.001) and siblings (12.60±11.83; p 0.001). Siblings and healthy controls also showed statistically significant differences in FAST total scores (p = 0.008). Patients performed worse than healthy controls on all CVLT sub-tests (p < 0.030) and in the number of correctly completed categories on WCST (p = 0.030). Siblings did not differ from healthy controls in cognitive tests. Unaffected siblings of patients with BD may show poorer functional performance compared to healthy controls. FAST scores may contribute to the development of markers of vulnerability and endophenotypic traits in at-risk populations.

Ares I-X Flight Test Validation of Control Design Tools in the Frequency-Domain

NASA Technical Reports Server (NTRS)

Johnson, Matthew; Hannan, Mike; Brandon, Jay; Derry, Stephen

2011-01-01

A major motivation of the Ares I-X flight test program was to Design for Data, in order to maximize the usefulness of the data recorded in support of Ares I modeling and validation of design and analysis tools. The Design for Data effort was intended to enable good post-flight characterizations of the flight control system, the vehicle structural dynamics, and also the aerodynamic characteristics of the vehicle. To extract the necessary data from the system during flight, a set of small predetermined Programmed Test Inputs (PTIs) was injected directly into the TVC signal. These PTIs were designed to excite the necessary vehicle dynamics while exhibiting a minimal impact on loads. The method is similar to common approaches in aircraft flight test programs, but with unique launch vehicle challenges due to rapidly changing states, short duration of flight, a tight flight envelope, and an inability to repeat any test. This paper documents the validation effort of the stability analysis tools to the flight data which was performed by comparing the post-flight calculated frequency response of the vehicle to the frequency response calculated by the stability analysis tools used to design and analyze the preflight models during the control design effort. The comparison between flight day frequency response and stability tool analysis for flight of the simulated vehicle shows good agreement and provides a high level of confidence in the stability analysis tools for use in any future program. This is true for both a nominal model as well as for dispersed analysis, which shows that the flight day frequency response is enveloped by the vehicle s preflight uncertainty models.

Differential item functioning analysis of the Vanderbilt Expertise Test for cars.

PubMed

Lee, Woo-Yeol; Cho, Sun-Joo; McGugin, Rankin W; Van Gulick, Ana Beth; Gauthier, Isabel

2015-01-01

The Vanderbilt Expertise Test for cars (VETcar) is a test of visual learning for contemporary car models. We used item response theory to assess the VETcar and in particular used differential item functioning (DIF) analysis to ask if the test functions the same way in laboratory versus online settings and for different groups based on age and gender. An exploratory factor analysis found evidence of multidimensionality in the VETcar, although a single dimension was deemed sufficient to capture the recognition ability measured by the test. We selected a unidimensional three-parameter logistic item response model to examine item characteristics and subject abilities. The VETcar had satisfactory internal consistency. A substantial number of items showed DIF at a medium effect size for test setting and for age group, whereas gender DIF was negligible. Because online subjects were on average older than those tested in the lab, we focused on the age groups to conduct a multigroup item response theory analysis. This revealed that most items on the test favored the younger group. DIF could be more the rule than the exception when measuring performance with familiar object categories, therefore posing a challenge for the measurement of either domain-general visual abilities or category-specific knowledge.

Ice Growth Measurements from Image Data to Support Ice Crystal and Mixed-Phase Accretion Testing

NASA Technical Reports Server (NTRS)

Struk, Peter M.; Lynch, Christopher J.

2012-01-01

This paper describes the imaging techniques as well as the analysis methods used to measure the ice thickness and growth rate in support of ice-crystal icing tests performed at the National Research Council of Canada (NRC) Research Altitude Test Facility (RATFac). A detailed description of the camera setup, which involves both still and video cameras, as well as the analysis methods using the NASA Spotlight software, are presented. Two cases, one from two different test entries, showing significant ice growth are analyzed in detail describing the ice thickness and growth rate which is generally linear. Estimates of the bias uncertainty are presented for all measurements. Finally some of the challenges related to the imaging and analysis methods are discussed as well as methods used to overcome them.

Ice Growth Measurements from Image Data to Support Ice-Crystal and Mixed-Phase Accretion Testing

NASA Technical Reports Server (NTRS)

Struk, Peter, M; Lynch, Christopher, J.

2012-01-01

This paper describes the imaging techniques as well as the analysis methods used to measure the ice thickness and growth rate in support of ice-crystal icing tests performed at the National Research Council of Canada (NRC) Research Altitude Test Facility (RATFac). A detailed description of the camera setup, which involves both still and video cameras, as well as the analysis methods using the NASA Spotlight software, are presented. Two cases, one from two different test entries, showing significant ice growth are analyzed in detail describing the ice thickness and growth rate which is generally linear. Estimates of the bias uncertainty are presented for all measurements. Finally some of the challenges related to the imaging and analysis methods are discussed as well as methods used to overcome them.

Total hydrocarbon content (THC) testing in liquid oxygen (LOX) systems

NASA Astrophysics Data System (ADS)

Meneghelli, B. J.; Obregon, R. E.; Ross, H. R.; Hebert, B. J.; Sass, J. P.; Dirschka, G. E.

2015-12-01

The measured Total Hydrocarbon Content (THC) levels in liquid oxygen (LOX) systems at Stennis Space Center (SSC) have shown wide variations. Examples of these variations include the following: 1) differences between vendor-supplied THC values and those obtained using standard SSC analysis procedures; and 2) increasing THC values over time at an active SSC test stand in both storage and run vessels. A detailed analysis of LOX sampling techniques, analytical instrumentation, and sampling procedures will be presented. Additional data obtained on LOX system operations and LOX delivery trailer THC values during the past 12-24 months will also be discussed. Field test results showing THC levels and the distribution of the THC's in the test stand run tank, modified for THC analysis via dip tubes, will be presented.

Total Hydrocarbon Content (THC) Testing in Liquid Oxygen (LOX)

NASA Technical Reports Server (NTRS)

Meneghelli, B. J.; Obregon, R. E.; Ross, H. R.; Hebert, B. J.; Sass, J. P.; Dirschka, G. E.

2016-01-01

The measured Total Hydrocarbon Content (THC) levels in liquid oxygen (LOX) systems at Stennis Space Center (SSC) have shown wide variations. Examples of these variations include the following: 1) differences between vendor-supplied THC values and those obtained using standard SSC analysis procedures; and 2) increasing THC values over time at an active SSC test stand in both storage and run vessels. A detailed analysis of LOX sampling techniques, analytical instrumentation, and sampling procedures will be presented. Additional data obtained on LOX system operations and LOX delivery trailer THC values during the past 12-24 months will also be discussed. Field test results showing THC levels and the distribution of the THC's in the test stand run tank, modified for THC analysis via dip tubes, will be presented.

Ceramic regenerator systems development program. [for automobile gas turbine engines

NASA Technical Reports Server (NTRS)

Cook, J. A.; Fucinari, C. A.; Lingscheit, J. N.; Rahnke, C. J.

1977-01-01

Ceramic regenerator cores are considered that can be used in passenger car gas turbine engines, Stirling engines, and industrial/truck gas turbine engines. Improved materials and design concepts aimed at reducing or eliminating chemical attack were placed on durability test in Ford 707 industrial gas turbine engines. The results of 19,600 hours of turbine engine durability testing are described. Two materials, aluminum silicate and magnesium aluminum silicate, continue to show promise toward achieving the durability objectives of this program. A regenerator core made from aluminum silicate showed minimal evidence of chemical attack damage after 6935 hours of engine test at 800 C and another showed little distress after 3510 hours at 982 C. Results obtained in ceramic material screening tests, aerothermodynamic performance tests, stress analysis, cost studies, and material specifications are also included.

Changes in Word Usage Frequency May Hamper Intergenerational Comparisons of Vocabulary Skills: An Ngram Analysis of Wordsum, WAIS, and WISC Test Items

ERIC Educational Resources Information Center

Roivainen, Eka

2014-01-01

Research on secular trends in mean intelligence test scores shows smaller gains in vocabulary skills than in nonverbal reasoning. One possible explanation is that vocabulary test items become outdated faster compared to nonverbal tasks. The history of the usage frequency of the words on five popular vocabulary tests, the GSS Wordsum, Wechsler…

Using Set Covering with Item Sampling to Analyze the Infeasibility of Linear Programming Test Assembly Models

ERIC Educational Resources Information Center

Huitzing, Hiddo A.

2004-01-01

This article shows how set covering with item sampling (SCIS) methods can be used in the analysis and preanalysis of linear programming models for test assembly (LPTA). LPTA models can construct tests, fulfilling a set of constraints set by the test assembler. Sometimes, no solution to the LPTA model exists. The model is then said to be…

Can power-law scaling and neuronal avalanches arise from stochastic dynamics?

PubMed

Touboul, Jonathan; Destexhe, Alain

2010-02-11

The presence of self-organized criticality in biology is often evidenced by a power-law scaling of event size distributions, which can be measured by linear regression on logarithmic axes. We show here that such a procedure does not necessarily mean that the system exhibits self-organized criticality. We first provide an analysis of multisite local field potential (LFP) recordings of brain activity and show that event size distributions defined as negative LFP peaks can be close to power-law distributions. However, this result is not robust to change in detection threshold, or when tested using more rigorous statistical analyses such as the Kolmogorov-Smirnov test. Similar power-law scaling is observed for surrogate signals, suggesting that power-law scaling may be a generic property of thresholded stochastic processes. We next investigate this problem analytically, and show that, indeed, stochastic processes can produce spurious power-law scaling without the presence of underlying self-organized criticality. However, this power-law is only apparent in logarithmic representations, and does not survive more rigorous analysis such as the Kolmogorov-Smirnov test. The same analysis was also performed on an artificial network known to display self-organized criticality. In this case, both the graphical representations and the rigorous statistical analysis reveal with no ambiguity that the avalanche size is distributed as a power-law. We conclude that logarithmic representations can lead to spurious power-law scaling induced by the stochastic nature of the phenomenon. This apparent power-law scaling does not constitute a proof of self-organized criticality, which should be demonstrated by more stringent statistical tests.

Measurement and analysis of chatter in a compliant model of a drillstring equipped with a PDC bit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elsayed, M.A.; Raymond, D.W.

1999-11-09

Typical laboratory testing of Polycrystalline Diamond Compact (PDC) bits is performed on relatively rigid setups. Even in hard rock, PDC bits exhibit reasonable life using such testing schemes. Unfortunately, field experience indicates otherwise. In this paper, the authors show that introducing compliance in testing setups provides better simulation of actual field conditions. Using such a scheme, they show that chatter can be severe even in softer rock, such as sandstone, and very destructive to the cutters in hard rock, such as sierra white granite.

Aeroglaze Z306 black paint for cryogenic telescope use: outgassing and water vapor regain

NASA Astrophysics Data System (ADS)

McCroskey, Doug M.; Abell, George C.; Chidester, Mike H.

2000-09-01

This paper presents the results of an experimental investigation of Aeroglaze Z306 black paint used as a functional coating in a cryogenic telescope for the Space Based Infrared System (SBIRS) program. During ground testing of a DBIRS infrared sensor engineering test model (ETM), degradation of optical transmission was observed. Analysis showed that the degradation was caused by water vapor condensing onto sensor collection optics, which were operating at 120 to 130 K. Root cause analysis identified Aeroglaze Z306 black pain as a likely candidate source of the water vapor. Prior to ETM testing, the painted telescope housing was vacuum baked for 100 hours at 100 $DEGC. However ASTM E 595 test data show that significant water vapor regain occurs within 24 hours after vacuum bake-out. To obtain a detailed characterization of the black paint with respect to water vapor regain and subsequent removal under vacuum conditions, a test plan was developed involving a series of ASTM E 1559 test measurements. These tests improve our understanding of the processes involved and provide the basis for design of an on-orbit H2 bakeout capability for the SBIRS infrared sensor payload.

How do gait frequency and serum-replacement interval affect polyethylene wear in knee-wear simulator tests?

PubMed

Reinders, Jörn; Sonntag, Robert; Kretzer, Jan Philippe

2014-11-01

Polyethylene wear (PE) is known to be a limiting factor in total joint replacements. However, a standardized wear test (e.g. ISO standard) can only replicate the complex in vivo loading condition in a simplified form. In this study, two different parameters were analyzed: (a) Bovine serum, as a substitute for synovial fluid, is typically replaced every 500,000 cycles. However, a continuous regeneration takes place in vivo. How does serum-replacement interval affect the wear rate of total knee replacements? (b) Patients with an artificial joint show reduced gait frequencies compared to standardized testing. What is the influence of a reduced frequency? Three knee wear tests were run: (a) reference test (ISO), (b) testing with a shortened lubricant replacement interval, (c) testing with reduced frequency. The wear behavior was determined based on gravimetric measurements and wear particle analysis. The results showed that the reduced test frequency only had a small effect on wear behavior. Testing with 1 Hz frequency is therefore a valid method for wear testing. However, testing with a shortened replacement interval nearly doubled the wear rate. Wear particle analysis revealed only small differences in wear particle size between the different tests. Wear particles were not linearly released within one replacement interval. The ISO standard should be revised to address the marked effects of lubricant replacement interval on wear rate.

An experiment with spectral analysis of emotional speech affected by orthodontic appliances

NASA Astrophysics Data System (ADS)

Přibil, Jiří; Přibilová, Anna; Ďuračková, Daniela

2012-11-01

The contribution describes the effect of the fixed and removable orthodontic appliances on spectral properties of emotional speech. Spectral changes were analyzed and evaluated by spectrograms and mean Welch’s periodograms. This alternative approach to the standard listening test enables to obtain objective comparison based on statistical analysis by ANOVA and hypothesis tests. Obtained results of analysis performed on short sentences of a female speaker in four emotional states (joyous, sad, angry, and neutral) show that, first of all, the removable orthodontic appliance affects the spectrograms of produced speech.

Therapeutic effects of an alpha-casozepine and L-tryptophan supplemented diet on fear and anxiety in the cat.

PubMed

Landsberg, Gary; Milgram, Bill; Mougeot, Isabelle; Kelly, Stephanie; de Rivera, Christina

2017-06-01

Objectives This study assessed the anxiolytic effectiveness of a test diet (Royal Canin Feline Calm diet) supplemented with L-tryptophan and alpha-casozepine. Methods Subjects were 24 cats that were classified as mildly or markedly fearful based on the presence of a person in their home room. Three different protocols were used to assess anxiety: (1) evaluation of the response to a human in the cat's home room (home room test); (2) analysis of the response to placement in an empty test room (open-field test); and (3) analysis of the response to an unfamiliar human (human interaction test). All three protocols were first run at baseline, and the results were used to assign the animals to control and test diet groups that showed equivalent fear and anxiety. Both groups were retested on the three protocols after 2 weeks (test 1) and again after 4 weeks (test 2). Results The diet groups differed for two behavioral measures in the open-field test: inactivity duration and inactivity frequency. The control group showed statistically significant increases in inactivity duration between baseline and test 1 and baseline and test 2, while the group fed the test diet showed a marginally not significant decrease in inactivity duration between baseline and test 1 and a not significant decrease for test 2. There was also a significant increase in inactivity frequency between baseline and test 1 in the test diet group and marginally not significant decrease in the control group. There were no differences between groups in the approach of the cats toward people for the home room test and the human interaction test. Conclusions and relevance These results suggest that the test diet reduced the anxiety response to placement in an unfamiliar location, but that fear in the presence of an unfamiliar person was not counteracted by the diet.

Transmission Bearing Damage Detection Using Decision Fusion Analysis

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Lewicki, David G.; Decker, Harry J.

2004-01-01

A diagnostic tool was developed for detecting fatigue damage to rolling element bearings in an OH-58 main rotor transmission. Two different monitoring technologies, oil debris analysis and vibration, were integrated using data fusion into a health monitoring system for detecting bearing surface fatigue pitting damage. This integrated system showed improved detection and decision-making capabilities as compared to using individual monitoring technologies. This diagnostic tool was evaluated by collecting vibration and oil debris data from tests performed in the NASA Glenn 500 hp Helicopter Transmission Test Stand. Data was collected during experiments performed in this test rig when two unanticipated bearing failures occurred. Results show that combining the vibration and oil debris measurement technologies improves the detection of pitting damage on spiral bevel gears duplex ball bearings and spiral bevel pinion triplex ball bearings in a main rotor transmission.

Analysis of mechanical strength to fixing the femoral neck fracture in synthetic bone type Asnis

PubMed Central

Freitas, Anderson; Lula, Welder Fernandes; de Oliveira, Jonathan Sampaio; Maciel, Rafael Almeida; Souto, Diogo Ranier de Macedo; Godinho, Patrick Fernandes

2014-01-01

OBJECTIVE: To analyze the results of biomechanical assays of fixation of Pauwels type III femoral neck fracture in synthetic bone, using 7.5mm cannulated screws in inverted triangle formation, in relation to the control group. METHODS: Ten synthetic bones were used, from a domestic brand, divided into two groups: test and control. In the test group, a 70° tilt osteotomy of the femoral neck was fixated using three cannulated screws in inverted triangle formation. The resistance of this fixation and its rotational deviation were analyzed at 5mm displacement (phase 1) and 10mm displacement (phase 2). The control group was tested in its integrity until the fracture of the femoral neck occurred. The Mann-Whitney test was used for group analysis and comparison. RESULTS: The values in the test group in phase 1, in samples 1-5, showed a mean of 579N and SD =77N. Rotational deviations showed a mean of 3.33°, SD = 2.63°. In phase 2, the mean was 696N and SD =106N. The values of the maximum load in the control group had a mean of 1329N and SD=177N. CONCLUSION: The analysis of mechanical strength between the groups determined a statistically significant lower value in the test group. Level of Evidence III, Control Case. PMID:25246851

14 CFR 35.43 - Propeller hydraulic components.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Propeller hydraulic components. 35.43... AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.43 Propeller hydraulic components. Applicants must show by test, validated analysis, or both, that propeller components that contain hydraulic...

14 CFR 35.43 - Propeller hydraulic components.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Propeller hydraulic components. 35.43... AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.43 Propeller hydraulic components. Applicants must show by test, validated analysis, or both, that propeller components that contain hydraulic...

14 CFR 35.43 - Propeller hydraulic components.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Propeller hydraulic components. 35.43... AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.43 Propeller hydraulic components. Applicants must show by test, validated analysis, or both, that propeller components that contain hydraulic...

14 CFR 35.43 - Propeller hydraulic components.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Propeller hydraulic components. 35.43... AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.43 Propeller hydraulic components. Applicants must show by test, validated analysis, or both, that propeller components that contain hydraulic...

14 CFR 35.43 - Propeller hydraulic components.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Propeller hydraulic components. 35.43... AIRWORTHINESS STANDARDS: PROPELLERS Tests and Inspections § 35.43 Propeller hydraulic components. Applicants must show by test, validated analysis, or both, that propeller components that contain hydraulic...

Types of Sensory Integrative Dysfunction among Disabled Learners

ERIC Educational Resources Information Center

Ayres, A. Jean

1972-01-01

R-technique factor analysis was used to correlate results of sensorimotor, psycholinguistic and cognitive tests given to California children with learning disabilities. Results show not all children with specific neural disorders perform poorly on related tests where low scores would be expected. (PD)

Comparison of PanBio Dengue Duo Enzyme-Linked Immunosorbent Assay (ELISA) and MRL Dengue Fever Virus Immunoglobulin M Capture ELISA for Diagnosis of Dengue Virus Infections in Southeast Asia

PubMed Central

Cuzzubbo, Andrea J.; Vaughn, David W.; Nisalak, Ananda; Solomon, Tom; Kalayanarooj, Siripen; Aaskov, John; Dung, Nguyen Minh; Devine, Peter L.

1999-01-01

The performances of the MRL dengue fever virus immunoglobulin M (IgM) capture enzyme-linked immunosorbent assay (ELISA) and the PanBio Dengue Duo IgM capture and IgG capture ELISA were compared. Eighty sera from patients with dengue virus infections, 24 sera from patients with Japanese encephalitis (JE), and 78 sera from patients with nonflavivirus infections, such as malaria, typhoid, leptospirosis, and scrub typhus, were used. The MRL test showed superior sensitivity for dengue virus infections (94 versus 89%), while the PanBio test showed superior specificity for JE (79 versus 25%) and other infections (100 versus 91%). The PanBio ELISA showed better overall performance, as assessed by the sum of sensitivity and specificity (F value). When dengue virus and nonflavivirus infections were compared, F values of 189 and 185 were obtained for the PanBio and MRL tests, respectively, while when dengue virus infections and JE were compared, F values of 168 and 119 were obtained. The results obtained with individual sera in the PanBio and MRL IgM ELISAs showed good correlation, but this analysis revealed that the cutoff value of the MRL test was set well below that of the PanBio test. Comparing the sensitivity and specificity of the tests at different cutoff values (receiver-operator analysis) revealed that the MRL and PanBio IgM ELISAs performed similarly in distinguishing dengue virus from nonflavivirus infections, although the PanBio IgM ELISA showed significantly better distinction between dengue virus infections and JE. The implications of these findings for the laboratory diagnosis of dengue are discussed. PMID:10473522

More than 100 Colleges Fail Education Department's Test of Financial Strength

ERIC Educational Resources Information Center

Blumenstyk, Goldie

2009-01-01

A newly compiled analysis by the U.S. Department of Education and obtained by "The Chronicle" shows that 114 private nonprofit degree-granting colleges were in such fragile financial condition at the end of their last fiscal year that they failed the department's financial-responsibility test. Colleges that fail the test are subject to extra…

Forward Skirt Structural Testing on the Space Launch System (SLS) Program

NASA Technical Reports Server (NTRS)

Lohrer, J. D.; Wright, R. D.

2016-01-01

Structural testing was performed to evaluate heritage forward skirts from the Space Shuttle program for use on the NASA Space Launch System (SLS) program. Testing was needed because SLS ascent loads are 35% higher than Space Shuttle loads. Objectives of testing were to determine margins of safety, demonstrate reliability, and validate analytical models. Testing combined with analysis was able to show heritage forward skirts were acceptable to use on the SLS program.

Spectral analysis software improves confidence in plant and soil water stable isotope analyses performed by isotope ratio infrared spectroscopy (IRIS).

PubMed

West, A G; Goldsmith, G R; Matimati, I; Dawson, T E

2011-08-30

Previous studies have demonstrated the potential for large errors to occur when analyzing waters containing organic contaminants using isotope ratio infrared spectroscopy (IRIS). In an attempt to address this problem, IRIS manufacturers now provide post-processing spectral analysis software capable of identifying samples with the types of spectral interference that compromises their stable isotope analysis. Here we report two independent tests of this post-processing spectral analysis software on two IRIS systems, OA-ICOS (Los Gatos Research Inc.) and WS-CRDS (Picarro Inc.). Following a similar methodology to a previous study, we cryogenically extracted plant leaf water and soil water and measured the δ(2)H and δ(18)O values of identical samples by isotope ratio mass spectrometry (IRMS) and IRIS. As an additional test, we analyzed plant stem waters and tap waters by IRMS and IRIS in an independent laboratory. For all tests we assumed that the IRMS value represented the "true" value against which we could compare the stable isotope results from the IRIS methods. Samples showing significant deviations from the IRMS value (>2σ) were considered to be contaminated and representative of spectral interference in the IRIS measurement. Over the two studies, 83% of plant species were considered contaminated on OA-ICOS and 58% on WS-CRDS. Post-analysis, spectra were analyzed using the manufacturer's spectral analysis software, in order to see if the software correctly identified contaminated samples. In our tests the software performed well, identifying all the samples with major errors. However, some false negatives indicate that user evaluation and testing of the software are necessary. Repeat sampling of plants showed considerable variation in the discrepancies between IRIS and IRMS. As such, we recommend that spectral analysis of IRIS data must be incorporated into standard post-processing routines. Furthermore, we suggest that the results from spectral analysis be included when reporting stable isotope data from IRIS. Copyright © 2011 John Wiley & Sons, Ltd.

Utility of Urinary Protein-Creatinine Ratio and Protein Content in a 24-Hour Urine Collection in Systemic Lupus Erythematosus: A Systematic Review and Meta-Analysis.

PubMed

Medina-Rosas, Jorge; Yap, Kristy S; Anderson, Melanie; Su, Jiandong; Touma, Zahi

2016-09-01

To systematically review literature on the utility of spot urinary protein-creatinine ratio (PCR) as a screening test for proteinuria and its ability to accurately measure proteinuria compared with 24-hour urine collection (24H-P) in patients with systemic lupus erythematosus (SLE). We conducted a literature search (1900-2015) for articles comparing PCR and 24H-P in SLE patients in the databases Medline, Web of Science, and Embase. Included studies and their results were critically appraised and analyzed. Thirteen studies (1,001 patients; 84.01% women) were included. Ten studies reported on Pearson's correlation (range 0.67-0.94), and 3 studies reported on Spearman's correlation (range 0.78-1.00). The meta-analysis of studies with Pearson's correlation showed a high overall correlation of 0.80 between 24H-P and PCR, yet with high heterogeneity (I(2)  = 97.2%). Correlation analysis is not sufficient to evaluate the utility of a new test against the gold standard test, and analysis on agreement is required. Seven studies reported on agreement: 3 studies analyzed concordance correlation coefficient (0.48-0.94), 3 analyzed intraclass correlation coefficient (0.66-0.95), and 1 analyzed kappa coefficient (0.58). These results confirmed that the agreement between 24H-P and PCR was inappropriate. Three studies included Bland-Altman plots, and the results also demonstrated poor agreement between both tests. The PCR has a utility as a screening test for proteinuria in SLE patients. The studies' results of 24H-P and PCR showed poor agreement between both tests, signifying that PCR should not be a substitute for the gold standard test (24H-P) to accurately measure proteinuria. © 2016, American College of Rheumatology.

X-38 Bolt Retractor Subsystem Separation Demonstration

NASA Technical Reports Server (NTRS)

Rugless, Fedoria (Editor); Johnston, A. S.; Ahmed, R.; Garrison, J. C.; Gaines, J. L.; Waggoner, J. D.

2002-01-01

The Flight Robotics Laboratory FRL successfully demonstrated the X-38 bolt retractor subsystem (BRS). The BRS design was proven safe by testing in the Pyrotechnic Shock Facility (PSI) before being demonstrated in the FRL. This Technical Memorandum describes the BRS, FRL, PSF, and interface hardware. Bolt retraction time, spacecraft simulator acceleration, and a force analysis are also presented. The purpose of the demonstration was to show the FRL capability for spacecraft separation testing using pyrotechnics. Although a formal test was not performed due to schedule and budget constraints, the data will show that the BRS is a successful design concept and the FRL is suitable for future separation tests.

Further evidence for the increased power of LOD scores compared with nonparametric methods.

PubMed

Durner, M; Vieland, V J; Greenberg, D A

1999-01-01

In genetic analysis of diseases in which the underlying model is unknown, "model free" methods-such as affected sib pair (ASP) tests-are often preferred over LOD-score methods, although LOD-score methods under the correct or even approximately correct model are more powerful than ASP tests. However, there might be circumstances in which nonparametric methods will outperform LOD-score methods. Recently, Dizier et al. reported that, in some complex two-locus (2L) models, LOD-score methods with segregation analysis-derived parameters had less power to detect linkage than ASP tests. We investigated whether these particular models, in fact, represent a situation that ASP tests are more powerful than LOD scores. We simulated data according to the parameters specified by Dizier et al. and analyzed the data by using a (a) single locus (SL) LOD-score analysis performed twice, under a simple dominant and a recessive mode of inheritance (MOI), (b) ASP methods, and (c) nonparametric linkage (NPL) analysis. We show that SL analysis performed twice and corrected for the type I-error increase due to multiple testing yields almost as much linkage information as does an analysis under the correct 2L model and is more powerful than either the ASP method or the NPL method. We demonstrate that, even for complex genetic models, the most important condition for linkage analysis is that the assumed MOI at the disease locus being tested is approximately correct, not that the inheritance of the disease per se is correctly specified. In the analysis by Dizier et al., segregation analysis led to estimates of dominance parameters that were grossly misspecified for the locus tested in those models in which ASP tests appeared to be more powerful than LOD-score analyses.

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

14 CFR 25.307 - Proof of structure.

Code of Federal Regulations, 2012 CFR

2012-01-01

... load tests may be inadequate. (b)-(c) [Reserved] (d) When static or dynamic tests are used to show... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... condition. Structural analysis may be used only if the structure conforms to that for which experience has...

14 CFR 25.307 - Proof of structure.

Code of Federal Regulations, 2010 CFR

2010-01-01

... load tests may be inadequate. (b)-(c) [Reserved] (d) When static or dynamic tests are used to show... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... condition. Structural analysis may be used only if the structure conforms to that for which experience has...

14 CFR 25.307 - Proof of structure.

Code of Federal Regulations, 2013 CFR

2013-01-01

... load tests may be inadequate. (b)-(c) [Reserved] (d) When static or dynamic tests are used to show... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... condition. Structural analysis may be used only if the structure conforms to that for which experience has...

14 CFR 25.307 - Proof of structure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... load tests may be inadequate. (b)-(c) [Reserved] (d) When static or dynamic tests are used to show... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... condition. Structural analysis may be used only if the structure conforms to that for which experience has...

14 CFR 25.307 - Proof of structure.

Code of Federal Regulations, 2011 CFR

2011-01-01

... load tests may be inadequate. (b)-(c) [Reserved] (d) When static or dynamic tests are used to show... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... condition. Structural analysis may be used only if the structure conforms to that for which experience has...

Validity and Reliability Testing of an e-learning Questionnaire for Chemistry Instruction

NASA Astrophysics Data System (ADS)

Guspatni, G.; Kurniawati, Y.

2018-04-01

The aim of this paper is to examine validity and reliability of a questionnaire used to evaluate e-learning implementation in chemistry instruction. 48 questionnaires were filled in by students who had studied chemistry through e-learning system. The questionnaire consisted of 20 indicators evaluating students’ perception on using e-learning. Parametric testing was done as data were assumed to follow normal distribution. Item validity of the questionnaire was examined through item-total correlation using Pearson’s formula while its reliability was assessed with Cronbach’s alpha formula. Moreover, convergent validity was assessed to see whether indicators building a factor had theoretically the same underlying construct. The result of validity testing revealed 19 valid indicators while the result of reliability testing revealed Cronbach’s alpha value of .886. The result of factor analysis showed that questionnaire consisted of five factors, and each of them had indicators building the same construct. This article shows the importance of factor analysis to get a construct valid questionnaire before it is used as research instrument.

Spiral Bevel Gear Damage Detection Using Decision Fusion Analysis

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Handschuh, Robert F.; Afjeh, Abdollah A.

2002-01-01

A diagnostic tool for detecting damage to spiral bevel gears was developed. Two different monitoring technologies, oil debris analysis and vibration, were integrated using data fusion into a health monitoring system for detecting surface fatigue pitting damage on gears. This integrated system showed improved detection and decision-making capabilities as compared to using individual monitoring technologies. This diagnostic tool was evaluated by collecting vibration and oil debris data from fatigue tests performed in the NASA Glenn Spiral Bevel Gear Fatigue Rigs. Data was collected during experiments performed in this test rig when pitting damage occurred. Results show that combining the vibration and oil debris measurement technologies improves the detection of pitting damage on spiral bevel gears.

Diagnosis of cystic fibrosis with chloride meter (Sherwood M926S chloride analyzer®) and sweat test analysis system (CFΔ collection system®) compared to the Gibson Cooke method.

PubMed

Emiralioğlu, Nagehan; Özçelik, Uğur; Yalçın, Ebru; Doğru, Deniz; Kiper, Nural

2016-01-01

Sweat test with Gibson Cooke (GC) method is the diagnostic gold standard for cystic fibrosis (CF). Recently, alternative methods have been introduced to simplify both the collection and analysis of sweat samples. Our aim was to compare sweat chloride values obtained by GC method with other sweat test methods in patients diagnosed with CF and whose CF diagnosis had been ruled out. We wanted to determine if the other sweat test methods could reliably identify patients with CF and differentiate them from healthy subjects. Chloride concentration was measured with GC method, chloride meter and sweat test analysis system; also conductivity was determined with sweat test analysis system. Forty eight patients with CF and 82 patients without CF underwent the sweat test, showing median sweat chloride values 98.9 mEq/L with GC method, 101 mmol/L with chloride meter, 87.8 mmol/L with sweat test analysis system. In non-CF group, median sweat chloride values were 16.8 mEq/L with GC method, 10.5 mmol/L with chloride meter, and 15.6 mmol/L with sweat test analysis system. Median conductivity value was 107.3 mmol/L in CF group and 32.1 mmol/L in non CF group. There was a strong positive correlation between GC method and the other sweat test methods with a statistical significance (r=0.85) in all subjects. Sweat chloride concentration and conductivity by other sweat test methods highly correlate with the GC method. We think that the other sweat test equipments can be used as reliably as the classic GC method to diagnose or exclude CF.

Pleiotropy Analysis of Quantitative Traits at Gene Level by Multivariate Functional Linear Models

PubMed Central

Wang, Yifan; Liu, Aiyi; Mills, James L.; Boehnke, Michael; Wilson, Alexander F.; Bailey-Wilson, Joan E.; Xiong, Momiao; Wu, Colin O.; Fan, Ruzong

2015-01-01

In genetics, pleiotropy describes the genetic effect of a single gene on multiple phenotypic traits. A common approach is to analyze the phenotypic traits separately using univariate analyses and combine the test results through multiple comparisons. This approach may lead to low power. Multivariate functional linear models are developed to connect genetic variant data to multiple quantitative traits adjusting for covariates for a unified analysis. Three types of approximate F-distribution tests based on Pillai–Bartlett trace, Hotelling–Lawley trace, and Wilks’s Lambda are introduced to test for association between multiple quantitative traits and multiple genetic variants in one genetic region. The approximate F-distribution tests provide much more significant results than those of F-tests of univariate analysis and optimal sequence kernel association test (SKAT-O). Extensive simulations were performed to evaluate the false positive rates and power performance of the proposed models and tests. We show that the approximate F-distribution tests control the type I error rates very well. Overall, simultaneous analysis of multiple traits can increase power performance compared to an individual test of each trait. The proposed methods were applied to analyze (1) four lipid traits in eight European cohorts, and (2) three biochemical traits in the Trinity Students Study. The approximate F-distribution tests provide much more significant results than those of F-tests of univariate analysis and SKAT-O for the three biochemical traits. The approximate F-distribution tests of the proposed functional linear models are more sensitive than those of the traditional multivariate linear models that in turn are more sensitive than SKAT-O in the univariate case. The analysis of the four lipid traits and the three biochemical traits detects more association than SKAT-O in the univariate case. PMID:25809955

Pleiotropy analysis of quantitative traits at gene level by multivariate functional linear models.

PubMed

Wang, Yifan; Liu, Aiyi; Mills, James L; Boehnke, Michael; Wilson, Alexander F; Bailey-Wilson, Joan E; Xiong, Momiao; Wu, Colin O; Fan, Ruzong

2015-05-01

In genetics, pleiotropy describes the genetic effect of a single gene on multiple phenotypic traits. A common approach is to analyze the phenotypic traits separately using univariate analyses and combine the test results through multiple comparisons. This approach may lead to low power. Multivariate functional linear models are developed to connect genetic variant data to multiple quantitative traits adjusting for covariates for a unified analysis. Three types of approximate F-distribution tests based on Pillai-Bartlett trace, Hotelling-Lawley trace, and Wilks's Lambda are introduced to test for association between multiple quantitative traits and multiple genetic variants in one genetic region. The approximate F-distribution tests provide much more significant results than those of F-tests of univariate analysis and optimal sequence kernel association test (SKAT-O). Extensive simulations were performed to evaluate the false positive rates and power performance of the proposed models and tests. We show that the approximate F-distribution tests control the type I error rates very well. Overall, simultaneous analysis of multiple traits can increase power performance compared to an individual test of each trait. The proposed methods were applied to analyze (1) four lipid traits in eight European cohorts, and (2) three biochemical traits in the Trinity Students Study. The approximate F-distribution tests provide much more significant results than those of F-tests of univariate analysis and SKAT-O for the three biochemical traits. The approximate F-distribution tests of the proposed functional linear models are more sensitive than those of the traditional multivariate linear models that in turn are more sensitive than SKAT-O in the univariate case. The analysis of the four lipid traits and the three biochemical traits detects more association than SKAT-O in the univariate case. © 2015 WILEY PERIODICALS, INC.

Analysis/test correlation using VAWT-SDS on a step-relaxation test for the rotating Sandia 34 m test bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Argueello, J.G.; Dohrmann, C.R.; Carne, T.G.

The combined analysis/test effort described in this paper compares predictions with measured data from a step-relaxation test in the absence of significant wind-driven aerodynamic loading. The process described here is intended to illustrate a method for validation of time domain codes for structural analysis of wind turbine structures. Preliminary analyses were performed to investigate the transient dynamic response that the rotating Sandia 34 m Vertical Axis Wind Turbine (VAWT) would undergo when one of the two blades was excited by step-relaxation. The calculations served two purposes. The first was for pretest planning to evaluate the relative importance of the variousmore » forces that would be acting on the structure during the test and to determine if the applied force in the step-relaxation would be sufficient to produce an excitation that was distinguishable from that produced by the aerodynamic loads. The second was to provide predictions that could subsequently be compared to the data from the test. The test was carried out specifically to help in the validation of the time-domain structural dynamics code, VAWT-SDS, which predicts the dynamic response of VAWTs subject to transient events. Post-test comparisons with the data were performed and showed a qualitative agreement between pretest predictions and measured response. However, they also showed that there was significantly more damping in the measurements than included in the predictions. Efforts to resolve this difference, including post-test analyses, were undertaken and are reported herein. The overall effort described in this paper represents a major step in the process of arriving at a validated structural dynamics code.« less

The Measurement of Pressure Through Tubes in Pressure Distribution Tests

NASA Technical Reports Server (NTRS)

Hemke, Paul E

1928-01-01

The tests described in this report were made to determine the error caused by using small tubes to connect orifices on the surface of aircraft to central pressure capsules in making pressure distribution tests. Aluminum tubes of 3/16-inch inside diameter were used to determine this error. Lengths from 20 feet to 226 feet and pressures whose maxima varied from 2 inches to 140 inches of water were used. Single-pressure impulses for which the time of rise of pressure from zero to a maximum varied from 0.25 second to 3 seconds were investigated. The results show that the pressure recorded at the capsule on the far end of the tube lags behind the pressure at the orifice end and experiences also a change in magnitude. For the values used in these tests the time lag and pressure change vary principally with the time of rise of pressure from zero to a maximum and the tube length. Curves are constructed showing the time lag and pressure change. Empirical formulas are also given for computing the time lag. Analysis of pressure distribution tests made on airplanes in flight shows that the recorded pressures are slightly higher than the pressures at the orifice and that the time lag is negligible. The apparent increase in pressure is usually within the experimental error, but in the case of the modern pursuit type of airplane the pressure increase may be 5 per cent. For pressure-distribution tests on airships the analysis shows that the time lag and pressure change may be neglected.

Development and psychometric properties of the Inner Strength Scale.

PubMed

Lundman, Berit; Viglund, Kerstin; Aléx, Lena; Jonsén, Elisabeth; Norberg, Astrid; Fischer, Regina Santamäki; Strandberg, Gunilla; Nygren, Björn

2011-10-01

Four dimensions of inner strength were previously identified in a meta-theoretical analysis: firmness, creativity, connectedness, and flexibility. The aim of this study was to develop an Inner Strength Scale (ISS) based on those four dimensions and to evaluate its psychometric properties. An initial version of ISS was distributed for validation purpose with the Rosenberg Self-Esteem Scale, the resilience scale, and the sense of Coherence Scale. A convenience sample of 391 adults, aged 19-90 years participated. Principal component analysis (PCA) and confirmatory factor analysis (CFA) were used in the process of exploring, evaluating, and reducing the 63-item ISS to the 20-item ISS. Cronbach's alpha and test-retest were used to measure reliability. CFA showed satisfactory goodness-of-fit for the 20-item ISS. The analysis supported a fourfactor solution explaining 51% of the variance. Cronbach's alpha on the 20-item ISS was 0.86, and the test-retest showed stability over time (r=0.79). The ISS was found to be a valid and reliable instrument for capturing a multifaceted understanding of inner strength. Further tests of psychometric properties of the ISS will be performed in forthcoming studies. Copyright © 2011 Elsevier Ltd. All rights reserved.

Evaluation of the microsoft kinect skeletal versus depth data analysis for timed-up and go and figure of 8 walk tests.

PubMed

Hotrabhavananda, Benjamin; Mishra, Anup K; Skubic, Marjorie; Hotrabhavananda, Nijaporn; Abbott, Carmen

2016-08-01

We compared the performance of the Kinect skeletal data with the Kinect depth data in capturing different gait parameters during the Timed-up and Go Test (TUG) and Figure of 8 Walk Test (F8W). The gait parameters considered were stride length, stride time, and walking speed for the TUG, and number of steps and completion time for the F8W. A marker-based Vicon motion capture system was used for the ground-truth measurements. Five healthy participants were recruited for the experiment and were asked to perform three trials of each task. Results show that depth data analysis yields stride length and stride time measures with significantly low percentile errors as compared to the skeletal data analysis. However, the skeletal and depth data performed similar with less than 3% of absolute mean percentile error in determining the walking speed for the TUG and both parameters of F8W. The results show potential capabilities of Kinect depth data analysis in computing many gait parameters, whereas, the Kinect skeletal data can also be used for walking speed in TUG and F8W gait parameters.

Analysis of an Artificial Tailplane Icing Flight Test of a High-Wing, Twin-Engine Aircraft

NASA Astrophysics Data System (ADS)

Shaikh, Shehzad M.

The US Air Force Flight Test Center (AFFTC) conducted a civilian, Federal Aviation Administration (FAA) sponsored, evaluation of tailplane icing of a twin-turboprop business transport at Edwards Air Force Base. The flight test was conducted to evaluate ice shape growth and extent of ice on the tailplane for specific weather conditions of Liquid Water Content (LWC), droplet size, and ambient temperature. This work analyzes the flight test data comparing the drag for various tailplane icing conditions with respect to a flight test verified calibrated aircraft model. Although less than a third of the test aircraft was involved in the icing environment, the results of this analysis shows a significant increase in the aircraft drag with respect to the LWC, droplet size, and ambient temperature.

Pyrolysis of coal, biomass and their blends: performance assessment by thermogravimetric analysis.

PubMed

Ferrara, Francesca; Orsini, Alessandro; Plaisant, Alberto; Pettinau, Alberto

2014-11-01

With the aim to support the experimental tests in a gasification pilot plant, the thermal decomposition of coal, biomass and their mixtures has been carried out through a thermogravimetric analysis (TGA) and a simplified kinetic analysis. The TGA of pure fuels indicates the low reactivity of South African coal and the relatively high reactivity of Sardinian Sulcis coal during pyrolysis. Among the tested fuels, biomass (stone pine wood chips) is the most reactive one. These results fully confirm those obtained during the experimental tests in the gasification pilot plant. As for the fuel blends, the analysis shows that the synergic effects between the considered coals and biomass are negligible when they are co-pyrolyzed. The results of the analysis confirm that TGA could be very useful to generally predict the gasification performance and to optimize the experimental campaigns in pilot-scale gasification plants. Copyright © 2014 Elsevier Ltd. All rights reserved.

The "Reading the Mind in the Eyes" Test: Investigation of Psychometric Properties and Test-Retest Reliability of the Persian Version

ERIC Educational Resources Information Center

Khorashad, Behzad S.; Baron-Cohen, Simon; Roshan, Ghasem M.; Kazemian, Mojtaba; Khazai, Ladan; Aghili, Zahra; Talaei, Ali; Afkhamizadeh, Mozhgan

2015-01-01

The psychometric properties of the Persian "Reading the Mind in the Eyes" test were investigated, so were the predictions from the Empathizing-Systemizing theory of psychological sex differences. Adults aged 16-69 years old (N = 545, female = 51.7%) completed the test online. The analysis of items showed them to be generally acceptable.…

USB environment measurements based on full-scale static engine ground tests. [Upper Surface Blowing for YC-14

NASA Technical Reports Server (NTRS)

Sussman, M. B.; Harkonen, D. L.; Reed, J. B.

1976-01-01

Flow turning parameters, static pressures, surface temperatures, surface fluctuating pressures and acceleration levels were measured in the environment of a full-scale upper surface blowing (USB) propulsive-lift test configuration. The test components included a flightworthy CF6-50D engine, nacelle and USB flap assembly utilized in conjunction with ground verification testing of the USAF YC-14 Advanced Medium STOL Transport propulsion system. Results, based on a preliminary analysis of the data, generally show reasonable agreement with predicted levels based on model data. However, additional detailed analysis is required to confirm the preliminary evaluation, to help delineate certain discrepancies with model data and to establish a basis for future flight test comparisons.

Trend analysis of weekly acid rain data, 1978-83

USGS Publications Warehouse

Schertz, Terry L.; Hirsch, Robert M.

1985-01-01

There are 19 stations in the National Atmospheric Deposition Program which operated over the period 1978-83 and were subsequently incorporated into the National Trends Network in 1983. The precipitation chemistry data for these stations for this period were analyzed for trend, spatial correlation, seasonality, and relationship to precipitation volume. The intent of the analysis was to provide insights on the sources of variation in precipitation chemistry and to attempt to ascertain what statistical procedures may be most useful for ongoing analysis of the National Trends Network data. The Seasonal Kendall test was used for detection of trends in raw concentrations of dissolved constituents, pH and specific conductance, and residuals of these parameters from regression analysis. Forty-one percent of the trends detected in the raw concentrations were downtrends, 4 percent were uptrends, and 55 percent showed no trends at a = 0.2. At a more restrictive significance level of a = 0.05, 24 percent of the trends detected were downtrends, 2 percent were uptrends, and 74 percent showed no trends. The two constituents of greatest interest in terms of human generated emissions and environmental effects, sulfate and nitrate, showed only downtrends, and sulfate showed the largest decreases in concentration per year of all the ions tested.

FLiNaK Compatability Studies with Inconel 600 and Silicon Carbide

DOE PAGES

Yoder, Jr, Graydon L.; Heatherly, Dennis Wayne; Wilson, Dane F.; ...

2016-07-26

A small liquid fluoride salt test apparatus has been constructed and testing conducted to examine the compatibility of SiC, Inconel 600, and a spiral wound gasket material in FLiNaK salt. These tests were conducted to test materials and sealing systems that would be used in a FLiNaK salt test loop. Three months of testing at 700oC was used to assure that these materials and seals would be acceptable operating under expected test loop conditions. The SiC specimens showed little or no change over the test period while the spiral wound gasket material showed no degradation, except for the possibility ofmore » salt seeping into the outermost spirals of the gasket. The Inconel 600 specimens showed regions of voiding which penetrated the specimen surface to about 250 m in depth. Analysis indicated that the salt had leached chrome from the Inconel surface as was expected for this material. Because the test loop will have a limited working lifetime, it was concluded that these materials would be satisfactory for loop construction.« less

Design and Test of an Improved Crashworthiness Small Composite Airframe

NASA Technical Reports Server (NTRS)

Terry, James E.; Hooper, Steven J.; Nicholson, Mark

2002-01-01

The purpose of this small business innovative research (SBIR) program was to evaluate the feasibility of developing small composite airplanes with improved crashworthiness. A combination of analysis and half scale component tests were used to develop an energy absorbing airframe. Four full scale crash tests were conducted at the NASA Impact Dynamics Research Facility, two on a hard surface and two onto soft soil, replicating earlier NASA tests of production general aviation airplanes. Several seat designs and restraint systems including both an air bag and load limiting shoulder harnesses were tested. Tests showed that occupant loads were within survivable limits with the improved structural design and the proper combination of seats and restraint systems. There was no loss of cabin volume during the events. The analysis method developed provided design guidance but time did not allow extending the analysis to soft soil impact. This project demonstrated that survivability improvements are possible with modest weight penalties. The design methods can be readily applied by airplane designers using the examples in this report.

Transonic Unsteady Aerodynamics of the F/A-18E at Conditions Promoting Abrupt Wing Stall

NASA Technical Reports Server (NTRS)

Schuster, David M.; Byrd, James E.

2003-01-01

A transonic wind tunnel test of an 8% F/A-18E model was conducted in the NASA Langley Research Center (LaRC) 16-Foot Transonic Tunnel (16-Ft TT) to investigate the Abrupt Wing Stall (AWS) characteristics of this aircraft. During this test, both steady and unsteady measurements of balance loads, wing surface pressures, wing root bending moments, and outer wing accelerations were performed. The test was conducted with a wide range of model configurations and test conditions in an attempt to reproduce behavior indicative of the AWS phenomenon experienced on full-scale aircraft during flight tests. This paper focuses on the analysis of the unsteady data acquired during this test. Though the test apparatus was designed to be effectively rigid. model motions due to sting and balance flexibility were observed during the testing, particularly when the model was operating in the AWS flight regime. Correlation between observed aerodynamic frequencies and model structural frequencies are analyzed and presented. Significant shock motion and separated flow is observed as the aircraft pitches through the AWS region. A shock tracking strategy has been formulated to observe this phenomenon. Using this technique, the range of shock motion is readily determined as the aircraft encounters AWS conditions. Spectral analysis of the shock motion shows the frequencies at which the shock oscillates in the AWS region, and probability density function analysis of the shock location shows the propensity of the shock to take on a bi-stable and even tri-stable character in the AWS flight regime.

Sensitivity and Specificity of Eustachian Tube Function Tests in Adults

PubMed Central

Doyle, William J.; Swarts, J. Douglas; Banks, Julianne; Casselbrant, Margaretha L; Mandel, Ellen M; Alper, Cuneyt M.

2013-01-01

Objective Determine if Eustachian Tube (ET) function (ETF) tests can identify ears with physician-diagnosed ET dysfunction (ETD) in a mixed population at high sensitivity and specificity and define the inter-relatedness of ETF test parameters. Methods ETF was evaluated using the Forced-Response, Inflation-Deflation, Valsalva and Sniffing tests in 15 control ears of adult subjects after unilateral myringotomy (Group I) and in 23 ears of 19 adult subjects with ventilation tubes inserted for ETD (Group II). Data were analyzed using logistic regression including each parameter independently and then a step-down Discriminant Analysis including all ETF test parameters to predict group assignment. Factor Analysis operating over all parameters was used to explore relatedness. Results The Discriminant Analysis identified 4 ETF test parameters (Valsalva, ET opening pressure, dilatory efficiency and % positive pressure equilibrated) that together correctly assigned ears to Group II at a sensitivity of 95% and a specificity of 83%. Individual parameters representing the efficiency of ET opening during swallowing showed moderately accurate assignments of ears to their respective groups. Three factors captured approximately 98% of the variance among parameters, the first had negative loadings of the ETF structural parameters, the second had positive loadings of the muscle-assisted ET opening parameters and the third had negative loadings of the muscle-assisted ET opening parameters and positive loadings of the structural parameters. Discussion These results show that ETF tests can correctly assign individual ears to physician-diagnosed ETD with high sensitivity and specificity and that ETF test parameters can be grouped into structural-functional categories. PMID:23868429

Methods to increase reproducibility in differential gene expression via meta-analysis

PubMed Central

Sweeney, Timothy E.; Haynes, Winston A.; Vallania, Francesco; Ioannidis, John P.; Khatri, Purvesh

2017-01-01

Findings from clinical and biological studies are often not reproducible when tested in independent cohorts. Due to the testing of a large number of hypotheses and relatively small sample sizes, results from whole-genome expression studies in particular are often not reproducible. Compared to single-study analysis, gene expression meta-analysis can improve reproducibility by integrating data from multiple studies. However, there are multiple choices in designing and carrying out a meta-analysis. Yet, clear guidelines on best practices are scarce. Here, we hypothesized that studying subsets of very large meta-analyses would allow for systematic identification of best practices to improve reproducibility. We therefore constructed three very large gene expression meta-analyses from clinical samples, and then examined meta-analyses of subsets of the datasets (all combinations of datasets with up to N/2 samples and K/2 datasets) compared to a ‘silver standard’ of differentially expressed genes found in the entire cohort. We tested three random-effects meta-analysis models using this procedure. We showed relatively greater reproducibility with more-stringent effect size thresholds with relaxed significance thresholds; relatively lower reproducibility when imposing extraneous constraints on residual heterogeneity; and an underestimation of actual false positive rate by Benjamini–Hochberg correction. In addition, multivariate regression showed that the accuracy of a meta-analysis increased significantly with more included datasets even when controlling for sample size. PMID:27634930

Improving the analysis of slug tests

USGS Publications Warehouse

McElwee, C.D.

2002-01-01

This paper examines several techniques that have the potential to improve the quality of slug test analysis. These techniques are applicable in the range from low hydraulic conductivities with overdamped responses to high hydraulic conductivities with nonlinear oscillatory responses. Four techniques for improving slug test analysis will be discussed: use of an extended capability nonlinear model, sensitivity analysis, correction for acceleration and velocity effects, and use of multiple slug tests. The four-parameter nonlinear slug test model used in this work is shown to allow accurate analysis of slug tests with widely differing character. The parameter ?? represents a correction to the water column length caused primarily by radius variations in the wellbore and is most useful in matching the oscillation frequency and amplitude. The water column velocity at slug initiation (V0) is an additional model parameter, which would ideally be zero but may not be due to the initiation mechanism. The remaining two model parameters are A (parameter for nonlinear effects) and K (hydraulic conductivity). Sensitivity analysis shows that in general ?? and V0 have the lowest sensitivity and K usually has the highest. However, for very high K values the sensitivity to A may surpass the sensitivity to K. Oscillatory slug tests involve higher accelerations and velocities of the water column; thus, the pressure transducer responses are affected by these factors and the model response must be corrected to allow maximum accuracy for the analysis. The performance of multiple slug tests will allow some statistical measure of the experimental accuracy and of the reliability of the resulting aquifer parameters. ?? 2002 Elsevier Science B.V. All rights reserved.

40 CFR 80.126 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...% independent lab testing, the laboratory analysis shall consist of the results reported to the refinery or... trading records shall include worksheets and EPA reports showing actual and complying totals for benzene... evidencing the transfer of credits. (c) Designation records shall include laboratory analysis reports that...

40 CFR 80.126 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...% independent lab testing, the laboratory analysis shall consist of the results reported to the refinery or... trading records shall include worksheets and EPA reports showing actual and complying totals for benzene... evidencing the transfer of credits. (c) Designation records shall include laboratory analysis reports that...

Redundancy in the Iowa Tests of Basic Skills.

ERIC Educational Resources Information Center

Klein, Alice E.

1981-01-01

A factor analysis was performed for two levels of the Iowa Tests of Basic Skills (ITBS). Results showed that there was essentially one common factor with little evidence that the user would gain much nonredundant information from the 15 scores yielded by the ITBS. (Author/GK)

Atlas 5013 tank corrosion test

NASA Technical Reports Server (NTRS)

Sutherland, W. M.; Girton, L. D.; Treadway, D. G.

1978-01-01

The type and cause of corrosion in spot welded joints were determined by X-ray and chemical analysis. Fatigue and static tests showed the degree of degradation of mechanical properties. The corrosion inhibiting effectiveness of WD-40 compound and required renewal period by exposing typical joint specimens were examined.

Mode-Stirred Method Implementation for HIRF Susceptibility Testing and Results Comparison with Anechoic Method

NASA Technical Reports Server (NTRS)

Nguyen, Truong X.; Ely, Jay J.; Koppen, Sandra V.

2001-01-01

This paper describes the implementation of mode-stirred method for susceptibility testing according to the current DO-160D standard. Test results on an Engine Data Processor using the implemented procedure and the comparisons with the standard anechoic test results are presented. The comparison experimentally shows that the susceptibility thresholds found in mode-stirred method are consistently higher than anechoic. This is consistent with the recent statistical analysis finding by NIST that the current calibration procedure overstates field strength by a fixed amount. Once the test results are adjusted for this value, the comparisons with the anechoic results are excellent. The results also show that test method has excellent chamber to chamber repeatability. Several areas for improvements to the current procedure are also identified and implemented.

Toxicological and analytical investigations of noni (Morinda citrifolia) fruit juice.

PubMed

Westendorf, Johannes; Effenberger, Katharina; Iznaguen, Hassan; Basar, Simla

2007-01-24

Morinda citrifolia (noni) is known to contain genotoxic anthraquinones in the roots. Because of the widespread use of noni juice, the possible genotoxic risk was examined through a battery of short-term tests. Noni juice was also chemically analyzed for the possible presence of anthraquinones. Noni juice extract in the Salmonella microsome assay showed a slight mutagenic effect in strain TA1537, due to the presence of flavonoids. No mutagenicity was observed in the mammalian mutagenicity test with V79 Chinese hamster fibroblasts. Rats treated with a noni juice concentrate did not show DNA repair synthesis (UDS) in primary rat hepatocytes, nor could DNA adducts or DNA strand breaks be observed. HPLC analysis of noni juice for anthraquinones was negative, with a sensitivity of <1 ppm. In summary, chemical analysis and genotoxicity tests reveal that noni juice does not have a genotoxic potential and that genotoxic anthraquinones do not exist in noni juice.

Protocol vulnerability detection based on network traffic analysis and binary reverse engineering.

PubMed

Wen, Shameng; Meng, Qingkun; Feng, Chao; Tang, Chaojing

2017-01-01

Network protocol vulnerability detection plays an important role in many domains, including protocol security analysis, application security, and network intrusion detection. In this study, by analyzing the general fuzzing method of network protocols, we propose a novel approach that combines network traffic analysis with the binary reverse engineering method. For network traffic analysis, the block-based protocol description language is introduced to construct test scripts, while the binary reverse engineering method employs the genetic algorithm with a fitness function designed to focus on code coverage. This combination leads to a substantial improvement in fuzz testing for network protocols. We build a prototype system and use it to test several real-world network protocol implementations. The experimental results show that the proposed approach detects vulnerabilities more efficiently and effectively than general fuzzing methods such as SPIKE.

The 48-Pictures Test: a two-alternative forced-choice recognition test for the detection of malingering.

PubMed

Chouinard, M J; Rouleau, I

1997-11-01

We tested the validity of the 48-Pictures Test, a 2-alternative forced-choice recognition test, in detecting exaggerated memory impairments. This test maximizes subjective difficulty, through a large number of stimuli and shows minimal objective difficulty. We compared 17 suspected malingerers to 39 patients with memory impairments (6 amnesic, 15 frontal lobe dysfunctions, 18 other etiologies), and 17 normal adults instructed to simulate malingering on three memory tests: the 48-Pictures Test, the Rey Auditory Verbal Learning Test (RAVLT), and the Rey Complex Figure Test (RCFT). On the 48-Pictures Test, the clinical groups showed good recognition performance (amnesics: 85%; frontal dysfunction: 94%; other memory impairments: 97%), whereas the two simulator groups showed a poor performance (suspected malingerers: 62% correct; volunteer simulators 68% correct). The two other tests did not show a high degree of discrimination between the clinical groups and the simulator groups, except in 2 measures: the 2 simulator groups tended to show a performance decrement from the last recall trial to immediate recognition of the RAVLT and also performed better than the clinical groups on the immediate recall of the RCFT. A discriminant analysis with the latter 2 measures and the 48-Pictures Test correctly classified 96% of the participants. These results suggest that the 48-Pictures Test is a useful tool for the detection of possible simulated memory impairment and that when combined to the RAVLT recall-recognition difference score and to the immediate recall score on the RCFT can provide strong evidence of exaggerated memory impairment.

Medical University admission test: a confirmatory factor analysis of the results.

PubMed

Luschin-Ebengreuth, Marion; Dimai, Hans P; Ithaler, Daniel; Neges, Heide M; Reibnegger, Gilbert

2016-05-01

The Graz Admission Test has been applied since the academic year 2006/2007. The validity of the Test was demonstrated by a significant improvement of study success and a significant reduction of dropout rate. The purpose of this study was a detailed analysis of the internal correlation structure of the various components of the Graz Admission Test. In particular, the question investigated was whether or not the various test parts constitute a suitable construct which might be designated as "Basic Knowledge in Natural Science." This study is an observational investigation, analyzing the results of the Graz Admission Test for the study of human medicine and dentistry. A total of 4741 applicants were included in the analysis. Principal component factor analysis (PCFA) as well as techniques from structural equation modeling, specifically confirmatory factor analysis (CFA), were employed to detect potential underlying latent variables governing the behavior of the measured variables. PCFA showed good clustering of the science test parts, including also text comprehension. A putative latent variable "Basic Knowledge in Natural Science," investigated by CFA, was indeed shown to govern the response behavior of the applicants in biology, chemistry, physics, and mathematics as well as text comprehension. The analysis of the correlation structure of the various test parts confirmed that the science test parts together with text comprehension constitute a satisfactory instrument for measuring a latent construct variable "Basic Knowledge in Natural Science." The present results suggest the fundamental importance of basic science knowledge for results obtained in the framework of the admission process for medical universities.

Molecular analysis and test of linkage between the FMR-I gene and infantile autism in multiplex families

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hallmayer, J.; Pintado, E.; Lotspeich, L.

Approximately 2%-5% of autistic children show cytogenetic evidence of the fragile X syndrome. This report tests whether infantile autism in multiplex autism families arises from an unusual manifestion of the fragile X syndrome. This could arise either by expansion of the (CGG)n trinucleotide repeat in FMR-1 or from a mutation elsewhere in the gene. We studied 35 families that met stringent criteria for multiplex autism. Amplification of the trinucleotide repeat and analysis of methylation status were performed in 79 autistic children and in 31 of their unaffected siblings by Southern blot analysis. No examples of amplified repeats were seen inmore » the autistic or control children or in their parents or grandparents. We next examined the hypothesis that there was a mutation elsewhere in the FMR-1 gene, by linkage analysis in 32 of these families. We tested four different dominant models and a recessive model. Linkage to FMR-1 could be excluded (lod score between -24 and -62) in all models by using probes DXS548, FRAXAC1, and FRAXAC2 and the CGG repeat itself. Tests for heterogeneity in this sample were negative, and the occurrence of positive lod scores in this data set could be attributed to chance. Analysis of the data by the affected-sib method also did not show evidence for linkage of any marker to autism. These results enable us to reject the hypothesis that multiplex autism arises from expansion of the (CGG)n trinucleotide repeat in FMR-1. Further, because the overall lod scores for all probes in all models tested were highly negative, linkage to FMR-1 can also be ruled out in multiplex autistic families. 35 refs., 2 figs., 5 tabs.« less

Assessment of Geographic and Host-Associated Population Variations of the Carob Moth, Ectomyelois ceratoniae, on Pomegranate, Fig, Pistachio and Walnut, Using AFLP Markers

PubMed Central

Mozaffarian, Fariba; Mardi, Mohsen; Sarafrazi, Alimorad; Nouri Ganbalani, Gadir

2008-01-01

The carob moth, Ectomyelois ceratoniae (Zeller 1839) (Lepidoptera: Pyralidae) is the most important pest of pomegranate, Punica granatum L. (Myrtales: Ponicaceae), in Iran. In this study, 6 amplified fragment length polymorphism primer combinations were used to survey the genetic structure of the geographic and putative host-associated populations of this pest in Iran. An AMOVA was performed on test populations. Pairwise differences, Mantel test, multidimensional analysis, cluster analysis and migration rate were calculated for 5 geographic populations of E. ceratoniae sharing the same host, pomegranate. In another part of the study, 3 comparisons were performed on pairwise populations that were collected on different hosts (pomegranate, fig, pistachio and walnut) in same geographic regions. The results showed high within population variation (85.51% of total variation), however geographic populations differed significantly. The Mantel test did not show correlations between genetic and geographic distances. The probable factors that affect genetic distances are discussed. Multidimensional scaling analysis, migration rate and cluster analysis on geographic populations showed that the Arsanjan population was the most different from the others while the Saveh population was more similar to the Sabzevar population. The comparisons didn't show any host fidelity in test populations. It seems that the ability of E. ceratoniae to broaden its host range with no fidelity to hosts can decrease the efficiency of common control methods that are used on pomegranate. The results of this study suggest that in spite of the effects of geographic barriers, high within-population genetic variation, migration rate and gene flow can provide the opportunity for emerging new phenotypes or behaviors in pest populations, such as broadening host range, changing egg lying places, or changing over-wintering sites to adapt to difficult conditions such as those caused by intensive control methods. PMID:20345296

Differential item functioning analysis of the Vanderbilt Expertise Test for cars

PubMed Central

Lee, Woo-Yeol; Cho, Sun-Joo; McGugin, Rankin W.; Van Gulick, Ana Beth; Gauthier, Isabel

2015-01-01

The Vanderbilt Expertise Test for cars (VETcar) is a test of visual learning for contemporary car models. We used item response theory to assess the VETcar and in particular used differential item functioning (DIF) analysis to ask if the test functions the same way in laboratory versus online settings and for different groups based on age and gender. An exploratory factor analysis found evidence of multidimensionality in the VETcar, although a single dimension was deemed sufficient to capture the recognition ability measured by the test. We selected a unidimensional three-parameter logistic item response model to examine item characteristics and subject abilities. The VETcar had satisfactory internal consistency. A substantial number of items showed DIF at a medium effect size for test setting and for age group, whereas gender DIF was negligible. Because online subjects were on average older than those tested in the lab, we focused on the age groups to conduct a multigroup item response theory analysis. This revealed that most items on the test favored the younger group. DIF could be more the rule than the exception when measuring performance with familiar object categories, therefore posing a challenge for the measurement of either domain-general visual abilities or category-specific knowledge. PMID:26418499

Overview of NASA White Sands Test Facility Composite Overwrapped Pressure Vessel Testing

NASA Technical Reports Server (NTRS)

Greene, Nathanael; Saulsberry, Regor; Thesken, John; Phoenix, Leigh

2006-01-01

This viewgraph presentation examines the White Sands Test Facility testing of Composite overwrapped pressure vessel (COPV). A COPV is typically a metallic liner overwrapped with a fiber epoxy matrix. There is a weight advantage over the traditional all metal design. The presentation shows pictures of the facilities at White Sands, and then examines some of the testing performed. The tests include fluids compatibility, and Kevlar COPV. Data for the Kevlar tests are given, and an analysis is reviewed. There is also a comparison between Carbon COPVs and the Kevlar COPVs.

Characterization of Estrogen and Androgen Activity of Food Contact Materials by Different In Vitro Bioassays (YES, YAS, ERα and AR CALUX) and Chromatographic Analysis (GC-MS, HPLC-MS)

PubMed Central

Osorio, Veronica; Grininger, Angelika; Richter, Alexander; Bergmair, Johannes; Pyerin, Michael; Washüttl, Michael; Tacker, Manfred

2014-01-01

Endocrine active substances (EAS) show structural similarities to natural hormones and are suspected to affect the human endocrine system by inducing hormone dependent effects. Recent studies with in vitro tests suggest that EAS can leach from packaging into food and may therefore pose a risk to human health. Sample migrates from food contact materials were tested for estrogen and androgen agonists and antagonists with different commonly used in vitro tests. Additionally, chemical trace analysis by GC-MS and HPLC-MS was used to identify potential hormone active substances in sample migrates. A GC-MS method to screen migrates for 29 known or potential endocrine active substances was established and validated. Samples were migrated according to EC 10/2011, concentrated by solid phase extraction and tested with estrogen and androgen responsive reporter gene assays based on yeast cells (YES and YAS) or human osteoblast cells (ERα and AR CALUX). A high level of agreement between the different bioassays could be observed by screening for estrogen agonists. Four out of 18 samples tested showed an estrogen activity in a similar range in both, YES and ERα CALUX. Two more samples tested positive in ERα CALUX due to the lower limits of detection in this assay. Androgen agonists could not be detected in any of the tested samples, neither with YAS nor with AR CALUX. When testing for antagonists, significant differences between yeast and human cell-based bioassays were noticed. Using YES and YAS many samples showed a strong antagonistic activity which was not observed using human cell-based CALUX assays. By GC-MS, some known or supposed EAS were identified in sample migrates that showed a biological activity in the in vitro tests. However, no firm conclusions about the sources of the observed hormone activity could be obtained from the chemical results. PMID:25000404

Analysis of Test Criteria for Specifying Foam Firefighting Agents for Aircraft Rescue and Firefighting

DTIC Science & Technology

1994-08-01

version of the MIL SPEC, MIL - F - 24385 Rev. F’ 3. Figure 1 shows the results of the "modeling" experiments. This shows that, for a control time of 60...the military specification, MiL - F - 24385 ’. It was noted in the Background Section that the FAA does not have specific test criteria for foam agents, The...SPECIFICATION TESTS FOR FOAM Type of Foam_ United States/North America UL 162 All types MIL - F - 24385 A,14FT OF 555 Protein 2?GP74 (Canada) AFFF L-urope

Dynamic analysis and vibration testing of CFRP drive-line system used in heavy-duty machine tool

NASA Astrophysics Data System (ADS)

Yang, Mo; Gui, Lin; Hu, Yefa; Ding, Guoping; Song, Chunsheng

2018-03-01

Low critical rotary speed and large vibration in the metal drive-line system of heavy-duty machine tool affect the machining precision seriously. Replacing metal drive-line with the CFRP drive-line can effectively solve this problem. Based on the composite laminated theory and the transfer matrix method (TMM), this paper puts forward a modified TMM to analyze dynamic characteristics of CFRP drive-line system. With this modified TMM, the CFRP drive-line of a heavy vertical miller is analyzed. And the finite element modal analysis model of the shafting is established. The results of the modified TMM and finite element analysis (FEA) show that the modified TMM can effectively predict the critical rotary speed of CFRP drive-line. And the critical rotary speed of CFRP drive-line is 20% higher than that of the original metal drive-line. Then, the vibration of the CFRP and the metal drive-line were tested. The test results show that application of the CFRP drive shaft in the drive-line can effectively reduce the vibration of the heavy-duty machine tool.

Length bias correction in gene ontology enrichment analysis using logistic regression.

PubMed

Mi, Gu; Di, Yanming; Emerson, Sarah; Cumbie, Jason S; Chang, Jeff H

2012-01-01

When assessing differential gene expression from RNA sequencing data, commonly used statistical tests tend to have greater power to detect differential expression of genes encoding longer transcripts. This phenomenon, called "length bias", will influence subsequent analyses such as Gene Ontology enrichment analysis. In the presence of length bias, Gene Ontology categories that include longer genes are more likely to be identified as enriched. These categories, however, are not necessarily biologically more relevant. We show that one can effectively adjust for length bias in Gene Ontology analysis by including transcript length as a covariate in a logistic regression model. The logistic regression model makes the statistical issue underlying length bias more transparent: transcript length becomes a confounding factor when it correlates with both the Gene Ontology membership and the significance of the differential expression test. The inclusion of the transcript length as a covariate allows one to investigate the direct correlation between the Gene Ontology membership and the significance of testing differential expression, conditional on the transcript length. We present both real and simulated data examples to show that the logistic regression approach is simple, effective, and flexible.

Sensory Evaluation of Locally-grown Fruit Purees and Inulin Fibre on Probiotic Yogurt in Mwanza, Tanzania and the Microbial Analysis of Probiotic Yogurt Fortified with Moringa oleifera

PubMed Central

Morgan, Kathryn; Soltani, Mohammad; Gough, Robert

2015-01-01

ABSTRACT The purpose of this study was to establish new food products that increase the nutritional value and health benefits of the probiotic yogurt currently used in the Western Heads East (WHE) Project in Mwanza, Tanzania. The probiotic yogurt has established health benefits, and product development through fortification must not adversely affect the acceptability of yogurt or the viability of the probiotics. Both sensory testing and microbial analysis testing were conducted. The products tested were yogurt fortified with locally-grown fruit purees with inulin and Moringa oleifera. The results of the sensory evaluation showed that all yogurts were not rated significantly different from the control, except for appearance. The avocado puree without inulin rated significantly lower in all categories. The microbial analysis showed that Moringa oleifera did not negatively affect the growth of Lactobacillus rhamnosus GR-1 in MRS, milk or yogurt, although a significant decrease was found after 5 weeks of storage at 4 oC. PMID:25995722

Discriminant analysis of functional optical topography for schizophrenia diagnosis

NASA Astrophysics Data System (ADS)

Chuang, Ching-Cheng; Nakagome, Kazuyuki; Pu, Shenghong; Lan, Tsuo-Hung; Lee, Chia-Yen; Sun, Chia-Wei

2014-01-01

Abnormal prefrontal function plays a central role in the cognition deficits of schizophrenic patients; however, the character of the relationship between discriminant analysis and prefrontal activation remains undetermined. Recently, evidence of low prefrontal cortex (PFC) activation in individuals with schizophrenia has also been found during verbal fluency tests (VFT) and other cognitive tests with several neuroimaging methods. The purpose of this study is to assess the hemodynamic changes of the PFC and discriminant analysis between schizophrenia patients and healthy controls during VFT task by utilizing functional optical topography. A total of 99 subjects including 53 schizophrenic patients and 46 age- and gender-matched healthy controls were studied. The results showed that the healthy group had larger activation in the right and left PFC than in the middle PFC. Besides, the schizophrenic group showed weaker task performance and lower activation in the whole PFC than the healthy group. The result of the discriminant analysis showed a significant difference with P value <0.001 in six channels (CH 23, 29, 31, 40, 42, 52) between the schizophrenic and healthy groups. Finally, 68.69% and 71.72% of subjects are correctly classified as being schizophrenic or healthy with all 52 channels and six significantly different channels, respectively. Our findings suggest that the left PFC can be a feature region for discriminant analysis of schizophrenic diagnosis.

Spatial mapping and analysis of aerosols during a forest fire using computational mobile microscopy

NASA Astrophysics Data System (ADS)

Wu, Yichen; Shiledar, Ashutosh; Luo, Yi; Wong, Jeffrey; Chen, Cheng; Bai, Bijie; Zhang, Yibo; Tamamitsu, Miu; Ozcan, Aydogan

2018-02-01

Forest fires are a major source of particulate matter (PM) air pollution on a global scale. The composition and impact of PM are typically studied using only laboratory instruments and extrapolated to real fire events owing to a lack of analytical techniques suitable for field-settings. To address this and similar field test challenges, we developed a mobilemicroscopy- and machine-learning-based air quality monitoring platform called c-Air, which can perform air sampling and microscopic analysis of aerosols in an integrated portable device. We tested its performance for PM sizing and morphological analysis during a recent forest fire event in La Tuna Canyon Park by spatially mapping the PM. The result shows that with decreasing distance to the fire site, the PM concentration increases dramatically, especially for particles smaller than 2 µm. Image analysis from the c-Air portable device also shows that the increased PM is comparatively strongly absorbing and asymmetric, with an aspect ratio of 0.5-0.7. These PM features indicate that a major portion of the PM may be open-flame-combustion-generated element carbon soot-type particles. This initial small-scale experiment shows that c-Air has some potential for forest fire monitoring.

Curcumin-cyclodextrin encapsulated chitosan nanoconjugates with enhanced solubility and cell cytotoxicity.

PubMed

Popat, Amirali; Karmakar, Surajit; Jambhrunkar, Siddharth; Xu, Chun; Yu, Chengzhong

2014-05-01

Curcumin (CUR), a naturally derived anti-cancer cocktail is arguably the most widely studied neutraceutical. Despite a lot of promises, it is yet to reach the market as an active anti-cancer formulation. In the present study, we have prepared highly soluble (3 mg/ml) CUR-γ-hydroxypropyl cyclodextrin (CUR-CD) hollow spheres. CUR-CD hollow spheres were prepared by a novel and scalable spray drying method. CUR-CD was then encapsulated into positively charged biodegradable chitosan (CUR-CD-CS) nanoparticles. The CUR-CD-CS nanoparticles were characterised by TEM, SEM, DLS, drug loading and in vitro release. We tested the efficacy of these CUR-CD-CS nanoparticles in SCC25 cell lines using MTT assay and investigated its cellular uptake mechanism. We also studied Oligo DNA loading in CUR-CD-CS nanoparticles and its delivery via confocal imaging and FACS analysis. Our results demonstrated that CUR-CD-CS nanoparticles showed superior in vitro release performance and higher cytotoxicity in SCC25 cell line amongst all tested formulations. The cytotoxicity results were corroborated by cell cycle analysis and apoptosis test, showing nearly 100% apoptotic cell death in the case of CUR-CD-CS nanoparticles. Compared to CS nanoparticles, CS-CD nanoformulation showed higher cellular delivery of Cy3-Oligo DNA which was tested quantitatively using flowcytometry analysis, indicating that CD not only enhanced CUR solubility but also boosted the cellular uptake. Our study shows that rationally designed bio-degradable natural biomaterials have great potential as next generation nano-carriers for hydrophobic drug delivery such as CUR with potential of dual drug-gene delivery. Copyright © 2014 Elsevier B.V. All rights reserved.

A modified TNM staging system for non-metastatic colorectal cancer based on nomogram analysis of SEER database.

PubMed

Kong, Xiangxing; Li, Jun; Cai, Yibo; Tian, Yu; Chi, Shengqiang; Tong, Danyang; Hu, Yeting; Yang, Qi; Li, Jingsong; Poston, Graeme; Yuan, Ying; Ding, Kefeng

2018-01-08

To revise the American Joint Committee on Cancer TNM staging system for colorectal cancer (CRC) based on a nomogram analysis of Surveillance, Epidemiology, and End Results (SEER) database, and to prove the rationality of enhancing T stage's weighting in our previously proposed T-plus staging system. Total 115,377 non-metastatic CRC patients from SEER were randomly grouped as training and testing set by ratio 1:1. The Nomo-staging system was established via three nomograms based on 1-year, 2-year and 3-year disease specific survival (DSS) Logistic regression analysis of the training set. The predictive value of Nomo-staging system for the testing set was evaluated by concordance index (c-index), likelihood ratio (L.R.) and Akaike information criteria (AIC) for 1-year, 2-year, 3-year overall survival (OS) and DSS. Kaplan-Meier survival curve was used to valuate discrimination and gradient monotonicity. And an external validation was performed on database from the Second Affiliated Hospital of Zhejiang University (SAHZU). Patients with T1-2 N1 and T1N2a were classified into stage II while T4 N0 patients were classified into stage III in Nomo-staging system. Kaplan-Meier survival curves of OS and DSS in testing set showed Nomo-staging system performed better in discrimination and gradient monotonicity, and the external validation in SAHZU database also showed distinctly better discrimination. The Nomo-staging system showed higher value in L.R. and c-index, and lower value in AIC when predicting OS and DSS in testing set. The Nomo-staging system showed better performance in prognosis prediction and the weight of lymph nodes status in prognosis prediction should be cautiously reconsidered.

A benchmark for statistical microarray data analysis that preserves actual biological and technical variance.

PubMed

De Hertogh, Benoît; De Meulder, Bertrand; Berger, Fabrice; Pierre, Michael; Bareke, Eric; Gaigneaux, Anthoula; Depiereux, Eric

2010-01-11

Recent reanalysis of spike-in datasets underscored the need for new and more accurate benchmark datasets for statistical microarray analysis. We present here a fresh method using biologically-relevant data to evaluate the performance of statistical methods. Our novel method ranks the probesets from a dataset composed of publicly-available biological microarray data and extracts subset matrices with precise information/noise ratios. Our method can be used to determine the capability of different methods to better estimate variance for a given number of replicates. The mean-variance and mean-fold change relationships of the matrices revealed a closer approximation of biological reality. Performance analysis refined the results from benchmarks published previously.We show that the Shrinkage t test (close to Limma) was the best of the methods tested, except when two replicates were examined, where the Regularized t test and the Window t test performed slightly better. The R scripts used for the analysis are available at http://urbm-cluster.urbm.fundp.ac.be/~bdemeulder/.

Noninvasive methods for haemoglobin screening in prospective blood donors.

PubMed

Belardinelli, A; Benni, M; Tazzari, P L; Pagliaro, P

2013-08-01

The haemoglobin level of prospective blood donors is usually performed on blood obtained by from the finger pulp by fingerstick with a lancet and filling a capillary tube with a sample. New noninvasive methods are now available for rapid, noninvasive predonation haemoglobin screening. Prospective blood donors at our blood centre were tested, in two different trials, as follows: by the NBM 200 (OrSense) test (n = 445 donors) and by the Pronto-7 (Masimo) test (n = 463 donors). The haemoglobin values of each trial and the haemoglobin of finger pulp blood obtained by fingerstick with a lancet (HemoCue) were compared with the haemoglobin values obtained from a venous sample on a Cell Counter (Beckman Coulter). Comparison of Beckman Coulter Cell Counter and OrSense and results showed a bias of 0.29 g/dl, the standard deviation of the differences (SDD) of 0.98 and 95% limits of agreement from -1.64 to 2.21, using Bland and Altman statistical methodology. Comparison of Masimo and Beckman Coulter Cell Counter results showed a bias of -0.53 g/dl, SDD of 1.04 and 95% limits of agreement from -2.57 to 1.51. Cumulative analysis of all 908 donors, as tested by the usual fingerstick test showed a bias of 0.83 g/dl, SDD of 0.70 and 95% limits of agreement from -0.54 to 2.20 compared with the Coulter Cell Counter. Compared with the Coulter Counter, the specificity of the methods was 99.5% for fingerstick, 97% for OrSense and 83% for Massimo, and the sensitivity was 99, 98 and 93%, respectively. Analysis of finger pulp blood by either direct sampling by fingerstick and Hemocue, or by noninvasive haemoglobin tests does not replicate the results of cell counter analysis of venous samples. Compared with fingerstick, noninvasive haemoglobin tests eliminate pain and reduce stress, but have a lower level of specificity and sensitivity. © 2013 International Society of Blood Transfusion.

Fatigue Characterization of Alloy 10: a 1300F Disk Alloy for Small Gas Turbine Engines

NASA Technical Reports Server (NTRS)

Gayda, John

2000-01-01

A detailed fatigue characterization of Alloy 10, a high strength nickel-based disk alloy, was conducted on test coupons machined from a 'pancake' forging. Smooth bar, strain controlled fatigue testing at various R-ratios was run at representative bore, 750 F, and rim, 1300 F, temperatures. This was followed by notch fatigue testing (Kt=2) run under load control. Analysis of the fatigue data using a Smith-Watson-Topper approach and finite element analysis of the notch root was employed to understand material behavior in these tests. Smooth bar fatigue data showed a significant R-ratio dependence at either test temperature which could be accounted for using a Smith-Watson-Topper parameter (SWT). In general, fatigue life was longer at 750 F than 1300 F for a given SWT. For notch fatigue tests, life was longer at 750 F than 1300 F but only at higher stresses. This was attributed to differences in alloy strength. At lower stresses, finite element analysis suggested that convergence of fatigue life at both temperatures resulted from relaxation of stresses at the notch root in the 1300 F tests.

Analysis of Eighth Graders' Performance On Standardized Mathematics Tests.

ERIC Educational Resources Information Center

Meyinsse, Joseph; Tashakkori, Abbas

The main objective of this study was to show whether eighth graders' performance on standardized mathematics tests could be predicted from a variety of variables. These predictors included the students' race/ethnicity, gender, attitudes toward mathematics, students' time spent on homework, whether parents helped with homework assignments,…

Estimating and Testing Mediation Effects with Censored Data

ERIC Educational Resources Information Center

Wang, Lijuan; Zhang, Zhiyong

2011-01-01

This study investigated influences of censored data on mediation analysis. Mediation effect estimates can be biased and inefficient with censoring on any one of the input, mediation, and output variables. A Bayesian Tobit approach was introduced to estimate and test mediation effects with censored data. Simulation results showed that the Bayesian…

General Framework for Meta-analysis of Rare Variants in Sequencing Association Studies

PubMed Central

Lee, Seunggeun; Teslovich, Tanya M.; Boehnke, Michael; Lin, Xihong

2013-01-01

We propose a general statistical framework for meta-analysis of gene- or region-based multimarker rare variant association tests in sequencing association studies. In genome-wide association studies, single-marker meta-analysis has been widely used to increase statistical power by combining results via regression coefficients and standard errors from different studies. In analysis of rare variants in sequencing studies, region-based multimarker tests are often used to increase power. We propose meta-analysis methods for commonly used gene- or region-based rare variants tests, such as burden tests and variance component tests. Because estimation of regression coefficients of individual rare variants is often unstable or not feasible, the proposed method avoids this difficulty by calculating score statistics instead that only require fitting the null model for each study and then aggregating these score statistics across studies. Our proposed meta-analysis rare variant association tests are conducted based on study-specific summary statistics, specifically score statistics for each variant and between-variant covariance-type (linkage disequilibrium) relationship statistics for each gene or region. The proposed methods are able to incorporate different levels of heterogeneity of genetic effects across studies and are applicable to meta-analysis of multiple ancestry groups. We show that the proposed methods are essentially as powerful as joint analysis by directly pooling individual level genotype data. We conduct extensive simulations to evaluate the performance of our methods by varying levels of heterogeneity across studies, and we apply the proposed methods to meta-analysis of rare variant effects in a multicohort study of the genetics of blood lipid levels. PMID:23768515

Could Acoustic Emission Testing Show a Pipe Failure in Advance?

NASA Astrophysics Data System (ADS)

Soares, S. D.; Teixeira, J. C. G.

2004-02-01

During the last 20 years PETROBRAS has been attempting to use Acoustic Emission (AE) as an inspection tool. In this period the AE concept has changed from a revolutionary method to a way of finding areas to make a complete inspection. PETROBRAS has a lot of pressure vessels inspected by AE and with other NDTs techniques to establish their relationship. In other hand, PETROBRAS R&D Center has conducted destructive hydrostatic tests in pipelines samples with artificial defects made by milling. Those tests were monitored by acoustic emission and manual ultrasonic until the complete failure of pipe sample. This article shows the results obtained and a brief proposal of analysis criteria for this environment of test.

A Bayesian goodness of fit test and semiparametric generalization of logistic regression with measurement data.

PubMed

Schörgendorfer, Angela; Branscum, Adam J; Hanson, Timothy E

2013-06-01

Logistic regression is a popular tool for risk analysis in medical and population health science. With continuous response data, it is common to create a dichotomous outcome for logistic regression analysis by specifying a threshold for positivity. Fitting a linear regression to the nondichotomized response variable assuming a logistic sampling model for the data has been empirically shown to yield more efficient estimates of odds ratios than ordinary logistic regression of the dichotomized endpoint. We illustrate that risk inference is not robust to departures from the parametric logistic distribution. Moreover, the model assumption of proportional odds is generally not satisfied when the condition of a logistic distribution for the data is violated, leading to biased inference from a parametric logistic analysis. We develop novel Bayesian semiparametric methodology for testing goodness of fit of parametric logistic regression with continuous measurement data. The testing procedures hold for any cutoff threshold and our approach simultaneously provides the ability to perform semiparametric risk estimation. Bayes factors are calculated using the Savage-Dickey ratio for testing the null hypothesis of logistic regression versus a semiparametric generalization. We propose a fully Bayesian and a computationally efficient empirical Bayesian approach to testing, and we present methods for semiparametric estimation of risks, relative risks, and odds ratios when parametric logistic regression fails. Theoretical results establish the consistency of the empirical Bayes test. Results from simulated data show that the proposed approach provides accurate inference irrespective of whether parametric assumptions hold or not. Evaluation of risk factors for obesity shows that different inferences are derived from an analysis of a real data set when deviations from a logistic distribution are permissible in a flexible semiparametric framework. © 2013, The International Biometric Society.

On fractality and chaos in Moroccan family business stock returns and volatility

NASA Astrophysics Data System (ADS)

Lahmiri, Salim

2017-05-01

The purpose of this study is to examine existence of fractality and chaos in returns and volatilities of family business companies listed on the Casablanca Stock Exchange (CSE) in Morocco, and also in returns and volatility of the CSE market index. Detrended fluctuation analysis based Hurst exponent and fractionally integrated generalized autoregressive conditional heteroskedasticity (FIGARCH) model are used to quantify fractality in returns and volatility time series respectively. Besides, the largest Lyapunov exponent is employed to quantify chaos in both time series. The empirical results from sixteen family business companies follow. For return series, fractality analysis show that most of family business returns listed on CSE exhibit anti-persistent dynamics, whilst market returns have persistent dynamics. Besides, chaos tests show that business family stock returns are not chaotic while market returns exhibit evidence of chaotic behaviour. For volatility series, fractality analysis shows that most of family business stocks and market index exhibit long memory in volatility. Furthermore, results from chaos tests show that volatility of family business returns is not chaotic, whilst volatility of market index is chaotic. These results may help understanding irregularities patterns in Moroccan family business stock returns and volatility, and how they are different from market dynamics.

SEM analysis of defects and wear on Ni-Ti rotary instruments.

PubMed

Arantes, Werington Borges; da Silva, Celso Monteiro; Lage-Marques, José Luiz; Habitante, Sandramarcia; da Rosa, Luiz Carlos Laureano; de Medeiros, João Marcelo Ferreira

2014-01-01

SEM analysis of endodontic instruments from a Ni-Ti rotary system was assessed, before and after using them, considering their defects and deformations. Twenty Twisted File®, BioRąCe®, Mtwo®, and EndoWave® instruments were micrographed at 190× magnification. The files were washed and micrographed again to view alterations as to the presence or absence of irregular edges, grooves, microcavities, and scraping. Simulated root canal preparations were performed using these instruments. The instruments were cleaned and received a microscopic analysis after being used five times. After analysis tests were tested using Fisher's exact test and Kappa to evaluate the concordance among examiners. There was a statistically significant difference with respect to deformations between Twisted File® and other instruments (p < 0.05). There was no statistically significant difference in strains between the other groups (p > 0.05). All Twisted File® instruments showed the same defects; however damage were lower than those found in BioRace® and Mtwo®. The Endowave® did not show the same defects. In accordance with the data we conclude that the presence of defects was higher in Twisted File® instruments as the instruments and BioRace® Mtwo® brand, the defect rate was smaller and Endowave® instruments had no defects. Regarding the presence of wear after five uses among the groups all instruments showed changes in their cutting blades. © 2014 Wiley Periodicals, Inc.

Experimental testing and constitutive modeling of the mechanical properties of the swine skin tissue.

PubMed

Łagan, Sylwia D; Liber-Kneć, Aneta

2017-01-01

The aim of the study was an estimation of the possibility of using hyperelastic material models to fit experimental data obtained in the tensile test for the swine skin tissue. The uniaxial tensile tests of samples taken from the abdomen and back of a pig was carried out. The mechanical properties of the skin such as the mean Young's modulus, the mean maximum stress and the mean maximum elongation were calculated. The experimental data have been used to identify the parameters in specific strain-energy functions given in seven constitutive models of hyperelastic materials: neo-Hookean, Mooney-Rivlin, Ogden, Yeoh, Martins, Humphrey and Veronda-Westmann. An analysis of errors in fitting of theoretical and experimental data was done. Comparison of load -displacement curves for the back and abdomen regions of skin taken showed a different scope of both the mean maximum loading forces and the mean maximum elongation. Samples which have been prepared from the abdominal area had lower values of the mean maximum load compared to samples from the spine area. The reverse trend was observed during the analysis of the values of elongation. An analysis of the accuracy of model fitting to the experimental data showed that, the least accurate were the model of neo- -Hookean, model of Mooney-Rivlin for the abdominal region and model of Veronda-Westmann for the spine region. An analysis of seven hyperelastic material models showed good correlations between the experimental and the theoretical data for five models.

Subsonic Ultra Green Aircraft Research: Phase II- Volume III-Truss Braced Wing Aeroelastic Test Report

NASA Technical Reports Server (NTRS)

Bradley, Marty K.; Allen, Timothy J.; Droney, Christopher

2014-01-01

This Test Report summarizes the Truss Braced Wing (TBW) Aeroelastic Test (Task 3.1) work accomplished by the Boeing Subsonic Ultra Green Aircraft Research (SUGAR) team, which includes the time period of February 2012 through June 2014. The team consisted of Boeing Research and Technology, Boeing Commercial Airplanes, Virginia Tech, and NextGen Aeronautics. The model was fabricated by NextGen Aeronautics and designed to meet dynamically scaled requirements from the sized full scale TBW FEM. The test of the dynamically scaled SUGAR TBW half model was broken up into open loop testing in December 2013 and closed loop testing from January 2014 to April 2014. Results showed the flutter mechanism to primarily be a coalescence of 2nd bending mode and 1st torsion mode around 10 Hz, as predicted by analysis. Results also showed significant change in flutter speed as angle of attack was varied. This nonlinear behavior can be explained by including preload and large displacement changes to the structural stiffness and mass matrices in the flutter analysis. Control laws derived from both test system ID and FEM19 state space models were successful in suppressing flutter. The control laws were robust and suppressed flutter for a variety of Mach, dynamic pressures, and angle of attacks investigated.

Clinical evaluation of a novel population-based regression analysis for detecting glaucomatous visual field progression.

PubMed

Kovalska, M P; Bürki, E; Schoetzau, A; Orguel, S F; Orguel, S; Grieshaber, M C

2011-04-01

The distinction of real progression from test variability in visual field (VF) series may be based on clinical judgment, on trend analysis based on follow-up of test parameters over time, or on identification of a significant change related to the mean of baseline exams (event analysis). The aim of this study was to compare a new population-based method (Octopus field analysis, OFA) with classic regression analyses and clinical judgment for detecting glaucomatous VF changes. 240 VF series of 240 patients with at least 9 consecutive examinations available were included into this study. They were independently classified by two experienced investigators. The results of such a classification served as a reference for comparison for the following statistical tests: (a) t-test global, (b) r-test global, (c) regression analysis of 10 VF clusters and (d) point-wise linear regression analysis. 32.5 % of the VF series were classified as progressive by the investigators. The sensitivity and specificity were 89.7 % and 92.0 % for r-test, and 73.1 % and 93.8 % for the t-test, respectively. In the point-wise linear regression analysis, the specificity was comparable (89.5 % versus 92 %), but the sensitivity was clearly lower than in the r-test (22.4 % versus 89.7 %) at a significance level of p = 0.01. A regression analysis for the 10 VF clusters showed a markedly higher sensitivity for the r-test (37.7 %) than the t-test (14.1 %) at a similar specificity (88.3 % versus 93.8 %) for a significant trend (p = 0.005). In regard to the cluster distribution, the paracentral clusters and the superior nasal hemifield progressed most frequently. The population-based regression analysis seems to be superior to the trend analysis in detecting VF progression in glaucoma, and may eliminate the drawbacks of the event analysis. Further, it may assist the clinician in the evaluation of VF series and may allow better visualization of the correlation between function and structure owing to VF clusters. © Georg Thieme Verlag KG Stuttgart · New York.

Luminol testing in detecting modern human skeletal remains: a test on different types of bone tissue and a caveat for PMI interpretation.

PubMed

Caudullo, Giorgio; Caruso, Valentina; Cappella, Annalisa; Sguazza, Emanuela; Mazzarelli, Debora; Amadasi, Alberto; Cattaneo, Cristina

2017-01-01

When forensic pathologists and anthropologists have to deal with the evaluation of the post-mortem interval (PMI) in skeletal remains, luminol testing is frequently performed as a preliminary screening method. However, the repeatability of this test on the same bone, as well as comparative studies on different bones of the same individual, has never been performed. Therefore, with the aim of investigating the influence that different types of bones may exert on the response to the luminol test, the present study analysed three different skeletal elements (femoral diaphysis, vertebra and cranial vault), gathered from ten recent exhumed skeletons (all with a 20-year PMI). The analysis was performed twice on the same bone after 2 months: the analysis at time 0 concerned the whole bone, whereas the second concerned only a part of the same bone taken during the first test (which already had been broken). The overall results showed different responses, depending on the type of bone and on the integrity of the samples. Negative results at the first analysis (6.6% out of the total of samples) are consistent with what is reported in the literature, whilst at the second analysis, the increase of about 20% of false-negative results highlights that the luminol test ought to be performed with caution in case of broken bones or elements which are taphonomically altered. Results have thus proven that the exposition to environmental agents might result in haemoglobin (Hb) loss, as detected even after only 2 months. The study also focused on the crucial issue of the type of bone subjected to testing, remarking the suitability of the femoral diaphysis (100% of positive responses at the first analysis vs only 18% of false-negative results at the second test, corresponding to 5% of total false-negative results) as opposed to other bone elements that showed a low yield. In particular, the cranial vault gave poor results, with 40% of discrepancy between results from the two analyses, which suggests caution in choosing the type of bone sample to test. In conclusion, luminol testing should be used with caution on bones different from long bones or on non-intact bones.

The Diagnostic Performance of Stool DNA Testing for Colorectal Cancer: A Systematic Review and Meta-Analysis.

PubMed

Zhai, Rong-Lin; Xu, Fei; Zhang, Pei; Zhang, Wan-Li; Wang, Hui; Wang, Ji-Liang; Cai, Kai-Lin; Long, Yue-Ping; Lu, Xiao-Ming; Tao, Kai-Xiong; Wang, Guo-Bin

2016-02-01

This meta-analysis was designed to evaluate the diagnostic performance of stool DNA testing for colorectal cancer (CRC) and compare the performance between single-gene and multiple-gene tests.MEDLINE, Cochrane, EMBASE databases were searched using keywords colorectal cancers, stool/fecal, sensitivity, specificity, DNA, and screening. Sensitivity analysis, quality assessments, and performance bias were performed for the included studies.Fifty-three studies were included in the analysis with a total sample size of 7524 patients. The studies were heterogeneous with regard to the genes being analyzed for fecal genetic biomarkers of CRC, as well as the laboratory methods being used for each assay. The sensitivity of the different assays ranged from 2% to 100% and the specificity ranged from 81% to 100%. The meta-analysis found that the pooled sensitivities for single- and multigene assays were 48.0% and 77.8%, respectively, while the pooled specificities were 97.0% and 92.7%. Receiver operator curves and diagnostic odds ratios showed no significant difference between both tests with regard to sensitivity or specificity.This meta-analysis revealed that using assays that evaluated multiple genes compared with single-gene assays did not increase the sensitivity or specificity of stool DNA testing in detecting CRC.

The SNPforID Assay as a Supplementary Method in Kinship and Trace Analysis

PubMed Central

Schwark, Thorsten; Meyer, Patrick; Harder, Melanie; Modrow, Jan-Hendrick; von Wurmb-Schwark, Nicole

2012-01-01

Objective Short tandem repeat (STR) analysis using commercial multiplex PCR kits is the method of choice for kinship testing and trace analysis. However, under certain circumstances (deficiency testing, mutations, minute DNA amounts), STRs alone may not suffice. Methods We present a 50-plex single nucleotide polymorphism (SNP) assay based on the SNPs chosen by the SNPforID consortium as an additional method for paternity and for trace analysis. The new assay was applied to selected routine paternity and trace cases from our laboratory. Results and Conclusions Our investigation shows that the new SNP multiplex assay is a valuable method to supplement STR analysis, and is a powerful means to solve complicated genetic analyses. PMID:22851934

Task-based learning versus problem-oriented lecture in neurology continuing medical education.

PubMed

Vakani, Farhan; Jafri, Wasim; Ahmad, Amina; Sonawalla, Aziz; Sheerani, Mughis

2014-01-01

To determine whether general practitioners learned better with task-based learning or problem-oriented lecture in a Continuing Medical Education (CME) set-up. Quasi-experimental study. The Aga Khan University, Karachi campus, from April to June 2012. Fifty-nine physicians were given a choice to opt for either Task-based Learning (TBL) or Problem Oriented Lecture (PBL) in a continuing medical education set-up about headaches. The TBL group had 30 participants divided into 10 small groups, and were assigned case-based tasks. The lecture group had 29 participants. Both groups were given a pre and a post-test. Pre/post assessment was done using one-best MCQs. The reliability coefficient of scores for both the groups was estimated through Cronbach's alpha. An item analysis for difficulty and discriminatory indices was calculated for both the groups. Paired t-test was used to determine the difference between pre- and post-test scores of both groups. Independent t-test was used to compare the impact of the two teaching methods in terms of learning through scores produced by MCQ test. Cronbach's alpha was 0.672 for the lecture group and 0.881 for TBL group. Item analysis for difficulty (p) and discriminatory indexes (d) was obtained for both groups. The results for the lecture group showed pre-test (p) = 42% vs. post-test (p) = 43%; pre- test (d) = 0.60 vs. post-test (d) = 0.40. The TBL group showed pre -test (p) = 48% vs. post-test (p) = 70%; pre-test (d) = 0.69 vs. post-test (d) = 0.73. Lecture group pre-/post-test mean scores were (8.52 ± 2.95 vs. 12.41 ± 2.65; p < 0.001), where TBL group showed (9.70 ± 3.65 vs. 14 ± 3.99; p < 0.001). Independent t-test exhibited an insignificant difference at baseline (lecture 8.52 ± 2.95 vs. TBL 9.70 ± 3.65; p = 0.177). The post-scores were not statistically different lecture 12.41 ± 2.65 vs. TBL 14 ± 3.99; p = 0.07). Both delivery methods were found to be equally effective, showing statistically insignificant differences. However, TBL groups' post-test higher mean scores and radical increase in the post-test difficulty index demonstrated improved learning through TBL delivery and calls for further exploration of longitudinal studies in the context of CME.

Metallurgical characterization of orthodontic brackets produced by Metal Injection Molding (MIM).

PubMed

Zinelis, Spiros; Annousaki, Olga; Makou, Margarita; Eliades, Theodore

2005-11-01

The aim of this study was to investigate the bonding base surface morphology, alloy type, microstructure, and hardness of four types of orthodontic brackets produced by Metal Injection Molding technology (Discovery, Extremo, Freedom, and Topic). The bonding base morphology of the brackets was evaluated by scanning electron microscopy (SEM). Brackets from each manufacturer were embedded in epoxy resin, and after metallographic grinding, polishing and coating were analyzed by x-ray energy-dispersive spectroscopic (EDS) microanalysis to assess their elemental composition. Then, the brackets were subjected to metallographic etching to reveal their metallurgical structure. The same specimen surfaces were repolished and used for Vickers microhardness measurements. The results were statistically analyzed with one-way analysis of variance and Student-Newman-Keuls multiple comparison test at the 0.05 level of significance. The findings of SEM observations showed a great variability in the base morphology design among the brackets tested. The x-ray EDS analysis demonstrated that each bracket was manufactured from different ferrous or Co-based alloys. Metallographic analysis showed the presence of a large grain size for the Discovery, Freedom, and Topic brackets and a much finer grain size for the Extremo bracket. Vickers hardness showed great variations among the brackets (Topic: 287 +/- 16, Freedom: 248 +/- 13, Discovery: 214 +/- 12, and Extremo: 154 +/- 9). The results of this study showed that there are significant differences in the base morphology, composition, microstructure, and microhardness among the brackets tested, which may anticipate significant clinical implications.

The effects of overhead transparency design on retention, recall, and application of data analysis content.

PubMed

Van Hoozer, H; Brink, P J; Oppliger, R

1989-04-01

This experimental study tested the effects of overhead transparency design in conjunction with live lecture on retention, recall, and application of data analysis content over three occasions using a Solomon Four-Group, pretest-posttest design. Pretested subjects showed significant (p less than .001) gains in test scores from pre to posttest. No significant differences were found in pretest scores between control and experimental treatment groups or among the posttest scores of either the experimental or control groups.

Pneumatic testing in 45-degree-inclined boreholes in ash-flow tuff near Superior, Arizona

USGS Publications Warehouse

LeCain, G.D.

1995-01-01

Matrix permeability values determined by single-hole pneumatic testing in nonfractured ash-flow tuff ranged from 5.1 to 20.3 * 1046 m2 (meters squared), depending on the gas-injection rate and analysis method used. Results from the single-hole tests showed several significant correlations between permeability and injection rate and between permeability and test order. Fracture permeability values determined by cross-hole pneumatic testing in fractured ash-flow tuff ranged from 0.81 to 3.49 * 1044 m2, depending on injection rate and analysis method used. Results from the cross-hole tests monitor intervals showed no significant correlation between permeability and injection rate; however, results from the injection interval showed a significant correlation between injection rate and permeability. Porosity estimates from the 'cross-hole testing range from 0.8 to 2.0 percent. The maximum temperature change associated with the pneumatic testing was 1.2'(2 measured in the injection interval during cross-hole testing. The maximum temperature change in the guard and monitor intervals was O.Ip C. The maximum error introduced into the permeability values due to temperature fluctuations is approximately 4 percent. Data from temperature monitoring in the borehole indicated a positive correlation between the temperature decrease in the injection interval during recovery testing and the gas-injection rate. The thermocouple psychrometers indicated that water vapor was condensing in the boreholes during testing. The psychrometers in the guard and monitor intervals detected the drier injected gas as an increase in the dry bulb reading. The relative humidity in the test intervals was always higher than the upper measurement limit of the psychrometers. Although the installation of the packer system may have altered the water balance of the borehole, the gas-injection testing resulted in minimal or no changes in the borehole relative humidity.

Is there an association between flow diverter fish mouthing and delayed-type hypersensitivity to metals?-a case-control study.

PubMed

Kocer, Naci; Mondel, Prabath Kumar; Yamac, Elif; Kavak, Ayse; Kizilkilic, Osman; Islak, Civan

2017-11-01

Flow diverters are increasingly used in the treatment of complex and giant intracranial aneurysms. However, they are associated with complications like late aneurysmal rupture. Additionally, flow diverters show focal structural decrease in luminal diameter without any intimal hyperplasia. This resembles a "fish mouth" when viewed en face. In this pilot study, we tested the hypothesis of a possible association between flow diverter fish-mouthing and delayed-type hypersensitivity to its metal constituents. We retrospectively reviewed patient records from our center between May 2010 and November 2015. A total of nine patients had flow diverter fish mouthing. A control group of 25 patients was selected. All study participants underwent prospective patch test to detect hypersensitivity to flow diverter metal constituents. Analysis was performed using logistic regression analysis and Wilcoxon sign rank sum test. Univariate and multivariate analyses were performed to test variables to predict flow diverter fish mouthing. The association between flow diverter fish mouthing and positive patch test was not statistically significant. In multivariate analysis, history of allergy and maximum aneurysm size category was associated with flow diverter fish mouthing. This was further confirmed on Wilcoxon sign rank sum test. The study showed statistically significant association between flow diverter fish mouthing and history of contact allergy and a small aneurysmal size. Further large-scale studies are needed to detect a statistically significant association between flow diverter fish mouthing and patch test. We recommend early and more frequent follow-up imaging in patients with contact allergy to detect flow diverter fish mouthing and its subsequent evolution.

Baseline neuropsychological profile and cognitive response to cerebrospinal fluid shunting for idiopathic normal pressure hydrocephalus.

PubMed

Thomas, George; McGirt, Matthew J; Woodworth, Graeme; Heidler, Jennifer; Rigamonti, Daniele; Hillis, Argye E; Williams, Michael A

2005-01-01

To evaluate neurocognitive changes and predict neurocognitive outcome after ventriculoperitoneal shunting for idiopathic normal pressure hydrocephalus (INPH). Reports of neurocognitive response to shunting have been variable and studies that predict cognitive outcomes after shunting are limited. We reviewed our experience with cognitive outcomes for INPH patients who were selected for shunting based on abnormal cerebrospinal fluid (CSF) pressure monitoring and positive response in any of the NPH symptoms following large volume CSF drainage. Forty-two INPH patients underwent neurocognitive testing and Folstein Mini-Mental State Examination (MMSE) prior to shunting. Neurocognitive testing or MMSEwere performed at least 3 months after shunt insertion. Significant improvement in a neurocognitive subtest was defined as improvement by one standard deviation (1 SD) for the patient's age, sex and education level. Significant improvement in overall neurocognitive outcome was defined as a 4-point improvement in MMSE or improvement by 1 SD in 50% of the administered neurocognitive subtests. Nonparametric tests were used to assess changes. Predictors of outcome were assessed via logistic regression analysis. Twenty-two patients (52.3%) showed overall neurocognitive improvement, and significant improvement was seen in tests of verbal memory and psychomotor speed. Predictive analysis showed that patients scoring more than 1 SD below mean at baseline on verbal memory immediate recall were fourfold less likely to show overall cognitive improvement, and sixfold less likely if also associated with visuoconstructional deficit or executive dysfunction. Verbal memory scores at baseline were higher in patients who showed overall cognitive improvement. Shunting INPH patients on the basis of CSF pressure monitoring and drainage response shows a significant rate of cognitive improvement, and baseline neurocognitive test scores may distinguish patients likely to respond to shunt surgery from those who will not. Copyright (c) 2005 S. Karger AG, Basel.

The cognitive profile of myotonic dystrophy type 1: A systematic review and meta-analysis.

PubMed

Okkersen, Kees; Buskes, Melanie; Groenewoud, Johannes; Kessels, Roy P C; Knoop, Hans; van Engelen, Baziel; Raaphorst, Joost

2017-10-01

To examine the cognitive profile of patients with myotonic dystrophy type 1 (DM1) on the basis of a systematic review and meta-analysis of the literature. Embase, Medline and PsycInfo were searched for studies reporting ≥1 neuropsychological test in both DM1 patients and healthy controls. Search, data extraction and risk of bias analysis were independently performed by two authors to minimize error. Neuropsychological tests were categorized into 12 cognitive domains and effect sizes (Hedges' g) were calculated for each domain and for tests administered in ≥5 studies. DM1 participants demonstrated a significantly worse performance compared to controls in all cognitive domains. Effect sizes ranged from -.33 (small) for verbal memory to -1.01 (large) for visuospatial perception. Except for the domains global cognition, intelligence and social cognition, wide confidence intervals (CIs) were associated with moderate to marked statistical heterogeneity that necessitates careful interpretation of results. Out of the individual tests, the Rey-Osterrieth complex figure-copy (both non-verbal memory and visuoconstruction) showed consistent impairment with acceptable heterogeneity. In DM1 patients, cognitive deficits may include a variable combination of global cognitive impairment with involvement across different domains, including social cognition, memory and visuospatial functioning. Although DM1 is a heterogeneous disorder, our study shows that meta-analysis is feasible, contributes to the understanding of brain involvement and may direct bedside testing. The protocol for this study has been registered in PROSPERO (International prospective register of systematic reviews) under ID: 42016037415. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Tumor markers for bladder cancer: up-to-date study by the Kiel Tumor Bank].

PubMed

Hautmann, S; Eggers, J; Meyhoff, H; Melchior, D; Munk, A; Hamann, M; Naumann, M; Braun, P M; Jünemann, K P

2007-11-01

The number of noninvasive diagnostic tests for bladder cancer has increased tremendously over the last years with a large number of experimental and commercial tests. Comparative analyses of tests for diagnosis, follow-up, and recurrence detection of bladder cancer were performed retrospectively as well as prospectively, unicentrically, and multicentrically. An analysis of multicentric studies with large patient numbers compared with our own Kiel Tumor Bank data is presented. The Kiel Tumor Bank data looked prospectively at 106 consecutive bladder tumor patients from the year 2006. Special focus was put on urine cytology as a reference test, as well as the commercial NMP 22 Bladder Chek. The analysis of the NMP 22 Bladder Chek showed an overall sensitivity of 69% for all tumor grades and stages, with a specificity of 76%. Comparison to multicentric data with an overall sensitivity of 75% for all tumor grades and stages, with a specificity of 73%, showed results similar to those in the literature. Urine cytology showed a comparable overall sensitivity of 73% for all tumor grades and stages, with a specificity of 80%. A large number of noninvasive tests for bladder cancer follow-up with reasonable sensitivity and specificity can currently be used. Because of limited numbers of prospective randomized multicentric studies, no single particular marker for bladder cancer screening can be recommended at this point in time.

Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development and Performance Analysis

NASA Technical Reports Server (NTRS)

Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan; Kirchner, Robert; Engel, Carl D.

2014-01-01

The Space Launch System (SLS) base heating test is broken down into two test programs: (1) Pathfinder and (2) Main Test. The Pathfinder Test Program focuses on the design, development, hot-fire test and performance analyses of the 2% sub-scale SLS core-stage and booster element propulsion systems. The core-stage propulsion system is composed of four gaseous oxygen/hydrogen RS-25D model engines and the booster element is composed of two aluminum-based model solid rocket motors (SRMs). The first section of the paper discusses the motivation and test facility specifications for the test program. The second section briefly investigates the internal flow path of the design. The third section briefly shows the performance of the model RS-25D engines and SRMs for the conducted short duration hot-fire tests. Good agreement is observed based on design prediction analysis and test data. This program is a challenging research and development effort that has not been attempted in 40+ years for a NASA vehicle.

Discontinuation of reflex testing of stool samples for vancomycin-resistant enterococci resulted in increased prevalence.

PubMed

Bodily, Mandy; McMullen, Kathleen M; Russo, Anthony J; Kittur, Nupur D; Hoppe-Bauer, Joan; Warren, David K

2013-08-01

Discontinuation of reflex testing of stool submitted for Clostridium difficile testing for vancomycin-resistant enterococci (VRE) led to an increase in the number of patients with healthcare-associated VRE bacteremia and bacteriuria (0.21 vs 0.36 cases per 1,000 patient-days; P<.01). Cost-benefit analysis showed reflex screening and isolation of VRE reduced hospital costs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohapi, N.; Hees, A.; Larena, J., E-mail: n.mohapi@gmail.com, E-mail: a.hees@ru.ac.za, E-mail: j.larena@ru.ac.za

The Einstein Equivalence Principle is a fundamental principle of the theory of General Relativity. While this principle has been thoroughly tested with standard matter, the question of its validity in the Dark sector remains open. In this paper, we consider a general tensor-scalar theory that allows to test the equivalence principle in the Dark sector by introducing two different conformal couplings to standard matter and to Dark matter. We constrain these couplings by considering galactic observations of strong lensing and of velocity dispersion. Our analysis shows that, in the case of a violation of the Einstein Equivalence Principle, data favourmore » violations through coupling strengths that are of opposite signs for ordinary and Dark matter. At the same time, our analysis does not show any significant deviations from General Relativity.« less

Phytochemical analysis of Andrographis paniculata and Orthosiphon stamineus leaf extracts for their antibacterial and antioxidant potential.

PubMed

Malahubban, M; Alimon, A R; Sazili, A Q; Fakurazi, S; Zakry, F A

2013-09-01

Leaves of Andrographis paniculata and Orthosiphon stamineus were extracted with water, ethanol, methanol and chloroform to assess their potential as antibacterial and antioxidant agents. High performance liquid chromatography analysis showed that the methanolic extracts of A. paniculata and O. stamineus leaves gave the highest amounts of andrographolide and rosmarinic acid, respectively. These leaf extracts exhibited antimicrobial and antioxidant activities and, at the highest concentration tested (200 mg/mL), showed greater inhibitory effects against the Gram positive bacteria Bacillus cereus and Staphylococcus aureus than 10% acetic acid. Andrographis paniculata and O. stamineus methanolic and ethanolic leaf extracts also showed the strongest antioxidant activity as compared with the other extracts tested. The bioactive compounds present in these leaf extracts have the potential to be developed into natural antibacterial and antioxidant agents that may have applications in animal and human health.

Modeling and dynamic environment analysis technology for spacecraft

NASA Astrophysics Data System (ADS)

Fang, Ren; Zhaohong, Qin; Zhong, Zhang; Zhenhao, Liu; Kai, Yuan; Long, Wei

Spacecraft sustains complex and severe vibrations and acoustic environments during flight. Predicting the resulting structures, including numerical predictions of fluctuating pressure, updating models and random vibration and acoustic analysis, plays an important role during the design, manufacture and ground testing of spacecraft. In this paper, Monotony Integrative Large Eddy Simulation (MILES) is introduced to predict the fluctuating pressure of the fairing. The exact flow structures of the fairing wall surface under different Mach numbers are obtained, then a spacecraft model is constructed using the finite element method (FEM). According to the modal test data, the model is updated by the penalty method. On this basis, the random vibration and acoustic responses of the fairing and satellite are analyzed by different methods. The simulated results agree well with the experimental ones, which shows the validity of the modeling and dynamic environment analysis technology. This information can better support test planning, defining test conditions and designing optimal structures.

Analysis of quantitative data obtained from toxicity studies showing non-normal distribution.

PubMed

Kobayashi, Katsumi

2005-05-01

The data obtained from toxicity studies are examined for homogeneity of variance, but, usually, they are not examined for normal distribution. In this study I examined the measured items of a carcinogenicity/chronic toxicity study with rats for both homogeneity of variance and normal distribution. It was observed that a lot of hematology and biochemistry items showed non-normal distribution. For testing normal distribution of the data obtained from toxicity studies, the data of the concurrent control group may be examined, and for the data that show a non-normal distribution, non-parametric tests with robustness may be applied.

Is strength-training frequency a key factor to develop performance adaptations in young elite soccer players?

PubMed

Otero-Esquina, Carlos; de Hoyo Lora, Moisés; Gonzalo-Skok, Óliver; Domínguez-Cobo, Sergio; Sánchez, Hugo

2017-11-01

The aim of this study was to analyse the effects of a combined strength-training programme (full-back squat, YoYo TM leg curl, plyometrics and sled towing exercises) on performance in elite young soccer players and to examine the effects when this training programme was performed one or two days per week. Thirty-six male soccer players (U-17 to U-19) were recruited and assigned to experimental groups (EXP1: 1 s w -1 ; EXP2: 2 s w -1 ) or a control group (CON). Performance was assessed through a countermovement jump (CMJ) test (relative peak power [CMJ PP ] and CMJ height [CMJ H ]), a 20-m linear sprint test with split-times at 10-m, and a change of direction test (V-cut test) 1 week before starting the training programme and also 1 week after performing such training programme. Within-group analysis showed substantial improvements in CMJ variables (ES: 0.39-0.81) and COD (ES: 0.70 and 0.76) in EXP1 and EXP2, while EXP2 also showed substantial enhancements in all linear sprinting tests (ES: 0.43-0.52). Between-group analysis showed substantially greater improvements in CMJ variables (ES: 0.39-0.68) in experimental groups in comparison to CON. Furthermore, EXP2 achieved a substantial better performance in 20-m (ES: 0.48-0.64) than EXP1 and CON. Finally, EXP2 also showed greater enhancements in 10-m (ES: 0.50) and V-cut test (ES: 0.52) than EXP1. In conclusion, the combined strength-training programme improved jumping ability, independently of training frequency, though the achievement of two sessions per week also enhanced sprinting abilities (linear and COD) in young soccer players.

Evaluation of hematological and biochemical parameters of pesticide retailers following occupational exposure to a mixture of pesticides.

PubMed

Neghab, Masoud; Jalilian, Hamed; Taheri, Shekoufeh; Tatar, Mohsen; Haji Zadeh, Zeynab

2018-06-01

This study was undertaken to ascertain whether light occupational exposure to pesticides by retailers might be associated with any liver, kidney, nervous system dysfunction or hematological abnormalities. In this cross-sectional study, 70 male pesticide retailers (cases) and 64 male subjects, randomly selected from the constructions workers of city council contractors, as the referent group, were investigated. Urine and blood samples were taken from all subjects for urine analysis, hematological and biochemical parameters. Data analysis was conducted through SPSS v.19 using t-test and chi-square test. The results of urine analysis showed that the frequency of abnormal urine tests was significantly higher in cases than in referent individuals. Similarly, the results of CBC showed that the mean values of monocyte, hemoglobin, hematocrit, mean corpuscular volume, mean corpuscular hemoglobin and platelet distribution width were significantly lower, and mean corpuscular hemoglobin concentration and red blood cell distribution width were significantly higher in retailers. No significant differences were found for other parameters. These findings indicate that an association exists between exposure to pesticides by retailers and early subtle and sub-clinical changes in the urine tests and hematological parameters. Engineering measures are recommended to eliminate exposure to pesticides and to prevent its associated outcomes. Copyright © 2018 Elsevier Inc. All rights reserved.

Accurate estimation of normal incidence absorption coefficients with confidence intervals using a scanning laser Doppler vibrometer

NASA Astrophysics Data System (ADS)

Vuye, Cedric; Vanlanduit, Steve; Guillaume, Patrick

2009-06-01

When using optical measurements of the sound fields inside a glass tube, near the material under test, to estimate the reflection and absorption coefficients, not only these acoustical parameters but also confidence intervals can be determined. The sound fields are visualized using a scanning laser Doppler vibrometer (SLDV). In this paper the influence of different test signals on the quality of the results, obtained with this technique, is examined. The amount of data gathered during one measurement scan makes a thorough statistical analysis possible leading to the knowledge of confidence intervals. The use of a multi-sine, constructed on the resonance frequencies of the test tube, shows to be a very good alternative for the traditional periodic chirp. This signal offers the ability to obtain data for multiple frequencies in one measurement, without the danger of a low signal-to-noise ratio. The variability analysis in this paper clearly shows the advantages of the proposed multi-sine compared to the periodic chirp. The measurement procedure and the statistical analysis are validated by measuring the reflection ratio at a closed end and comparing the results with the theoretical value. Results of the testing of two building materials (an acoustic ceiling tile and linoleum) are presented and compared to supplier data.

Meta-analysis of gene-level associations for rare variants based on single-variant statistics.

PubMed

Hu, Yi-Juan; Berndt, Sonja I; Gustafsson, Stefan; Ganna, Andrea; Hirschhorn, Joel; North, Kari E; Ingelsson, Erik; Lin, Dan-Yu

2013-08-08

Meta-analysis of genome-wide association studies (GWASs) has led to the discoveries of many common variants associated with complex human diseases. There is a growing recognition that identifying "causal" rare variants also requires large-scale meta-analysis. The fact that association tests with rare variants are performed at the gene level rather than at the variant level poses unprecedented challenges in the meta-analysis. First, different studies may adopt different gene-level tests, so the results are not compatible. Second, gene-level tests require multivariate statistics (i.e., components of the test statistic and their covariance matrix), which are difficult to obtain. To overcome these challenges, we propose to perform gene-level tests for rare variants by combining the results of single-variant analysis (i.e., p values of association tests and effect estimates) from participating studies. This simple strategy is possible because of an insight that multivariate statistics can be recovered from single-variant statistics, together with the correlation matrix of the single-variant test statistics, which can be estimated from one of the participating studies or from a publicly available database. We show both theoretically and numerically that the proposed meta-analysis approach provides accurate control of the type I error and is as powerful as joint analysis of individual participant data. This approach accommodates any disease phenotype and any study design and produces all commonly used gene-level tests. An application to the GWAS summary results of the Genetic Investigation of ANthropometric Traits (GIANT) consortium reveals rare and low-frequency variants associated with human height. The relevant software is freely available. Copyright © 2013 The American Society of Human Genetics. Published by Elsevier Inc. All rights reserved.

FT-Raman spectroscopy, µ-EDXRF spectrometry, and microhardness analysis of the dentin of primary and permanent teeth.

PubMed

Torres, Carolina Paes; Miranda Gomes-Silva, Jaciara; Menezes-Oliveira, Maria Angélica Hueb; Silva Soares, Luís Eduardo; Palma-Dibb, Regina Guenka; Borsatto, Maria Cristina

2018-05-01

The chemical compositions (organic and inorganic contents) and mechanical behaviors of the dentin of permanent and deciduous teeth were analyzed and compared using X-ray fluorescence spectrometry (µ-EDXRF) Fourier transform Raman spectroscopy (FT-Raman) and a microhardness test (HD). Healthy fresh human primary and permanent molars (n = 10) were selected, The buccal surfaces facing upwards were stabilized in an acrylic plate, flattened, polished, and submitted to the µ-EDXRF, FT-Raman, and HD analysis. The results of the analysis were subjected to ANOVAs and Mann-Whitney U/Student's t multiple comparisons tests. The data showed similar values for the dentin of the primary and permanent teeth in P content, organic content (amide I peak), inorganic content ( PO43- - 430 and 590), and microhardness, Nevertheless, Ca content and Ca/P weight ratio were higher, and the CO32- peak was lower in the dentin of the permanent teeth compared to primary teeth. It be concluded that despite permanent teeth showed more Ca element, both substrates showed similar behavior of chemical and physical properties. © 2018 Wiley Periodicals, Inc.

KSC 50-MHz Doppler Radar Wind Profiler (DRWP) Operational Acceptance Test (OAT) Report

NASA Technical Reports Server (NTRS)

Barbre, Robert E.

2015-01-01

This report documents analysis results of the Kennedy Space Center updated 50-MHz Doppler Radar Wind Profiler (DRWP) Operational Acceptance Test (OAT). This test was designed to demonstrate that the new DRWP operates in a similar manner to the previous DRWP for use as a situational awareness asset for mission operations at the Eastern Range to identify rapid changes in the wind environment that weather balloons cannot depict. Data examination and two analyses showed that the updated DRWP meets the specifications in the OAT test plan and performs at least as well as the previous DRWP. Data examination verified that the DRWP provides complete profiles every five minutes from 1.8-19.5 km in vertical increments of 150 m. Analysis of 5,426 wind component reports from 49 concurrent DRWP and balloon profiles presented root mean square (RMS) wind component differences around 2.0 m/s. The DRWP's effective vertical resolution (EVR) was found to be 300 m for both the westerly and southerly wind component, which the best EVR possible given the DRWP's vertical sampling interval. A third analysis quantified the sensitivity to rejecting data that do not have adequate signal by assessing the number of first-guess propagations at each altitude. This report documents the data, quality control procedures, methodology, and results of each analysis. It also shows that analysis of the updated DRWP produced results that were at least as good as the previous DRWP with proper rationale. The report recommends acceptance of the updated DRWP for situational awareness usage as per the OAT's intent.

Benefits of a Low Severity Frontal Crash Test

PubMed Central

Digges, Kennerly; Dalmotas, Dainius

2007-01-01

The US Federal Motor Vehicle Safety Standard for frontal protection requires vehicle crash tests into a rigid barrier with two belted dummies in the front seats. The standard was recently modified to require two separate 56 Kph frontal tests. In one test the dummies are 50% males. In the other test, the dummies are 5% females. Analysis of crash test data indicates that the 56 Kph test does not encourage technology to reduce chest injuries in lower severity crashes. Tests conducted by Transport Canada provide data from belted 5% female dummies in the front seats of vehicles that were subjected crashes into a rigid barrier at 40 Kph. An analysis of the results showed that for many vehicles, the risks of serious chest injuries were higher in the 40 Kph test than in a 56 Kph test. This paper examines the benefits that would result from a requirement for a low severity (40 Kph) frontal barrier crash test with two belted 5% female dummies and more stringent chest injury requirements. A preliminary benefits analysis for chest deflection allowable in the range of 28 mm. to 36 mm. was conducted. A standard that limits the chest deflection to 34 mm. would reduce serious chest injury by 16% to 24% for the belted population in frontal crashes. PMID:18184499

Benefits of a low severity frontal crash test.

PubMed

Digges, Kennerly; Dalmotas, Dainius

2007-01-01

The US Federal Motor Vehicle Safety Standard for frontal protection requires vehicle crash tests into a rigid barrier with two belted dummies in the front seats. The standard was recently modified to require two separate 56 Kph frontal tests. In one test the dummies are 50% males. In the other test, the dummies are 5% females. Analysis of crash test data indicates that the 56 Kph test does not encourage technology to reduce chest injuries in lower severity crashes. Tests conducted by Transport Canada provide data from belted 5% female dummies in the front seats of vehicles that were subjected crashes into a rigid barrier at 40 Kph. An analysis of the results showed that for many vehicles, the risks of serious chest injuries were higher in the 40 Kph test than in a 56 Kph test. This paper examines the benefits that would result from a requirement for a low severity (40 Kph) frontal barrier crash test with two belted 5% female dummies and more stringent chest injury requirements. A preliminary benefits analysis for chest deflection allowable in the range of 28 mm. to 36 mm. was conducted. A standard that limits the chest deflection to 34 mm. would reduce serious chest injury by 16% to 24% for the belted population in frontal crashes.

Non-parametric characterization of long-term rainfall time series

NASA Astrophysics Data System (ADS)

Tiwari, Harinarayan; Pandey, Brij Kishor

2018-03-01

The statistical study of rainfall time series is one of the approaches for efficient hydrological system design. Identifying, and characterizing long-term rainfall time series could aid in improving hydrological systems forecasting. In the present study, eventual statistics was applied for the long-term (1851-2006) rainfall time series under seven meteorological regions of India. Linear trend analysis was carried out using Mann-Kendall test for the observed rainfall series. The observed trend using the above-mentioned approach has been ascertained using the innovative trend analysis method. Innovative trend analysis has been found to be a strong tool to detect the general trend of rainfall time series. Sequential Mann-Kendall test has also been carried out to examine nonlinear trends of the series. The partial sum of cumulative deviation test is also found to be suitable to detect the nonlinear trend. Innovative trend analysis, sequential Mann-Kendall test and partial cumulative deviation test have potential to detect the general as well as nonlinear trend for the rainfall time series. Annual rainfall analysis suggests that the maximum changes in mean rainfall is 11.53% for West Peninsular India, whereas the maximum fall in mean rainfall is 7.8% for the North Mountainous Indian region. The innovative trend analysis method is also capable of finding the number of change point available in the time series. Additionally, we have performed von Neumann ratio test and cumulative deviation test to estimate the departure from homogeneity. Singular spectrum analysis has been applied in this study to evaluate the order of departure from homogeneity in the rainfall time series. Monsoon season (JS) of North Mountainous India and West Peninsular India zones has higher departure from homogeneity and singular spectrum analysis shows the results to be in coherence with the same.

Aeroelastic stability analyses of two counter rotating propfan designs for a cruise missile model

NASA Technical Reports Server (NTRS)

Mahajan, Aparajit J.; Lucero, John M.; Mehmed, Oral; Stefko, George L.

1992-01-01

A modal aeroelastic analysis combining structural and aerodynamic models is applied to counterrotating propfans to evaluate their structural integrity for wind-tunnel testing. The aeroelastic analysis code is an extension of the 2D analysis code called the Aeroelastic Stability and Response of Propulsion Systems. Rotational speed and freestream Mach number are the parameters for calculating the stability of the two blade designs with a modal method combining a finite-element structural model with 2D steady and unsteady cascade aerodynamic models. The model demonstrates convergence to the least stable aeroelastic mode, describes the effects of a nonuniform inflow, and permits the modification of geometry and rotation. The analysis shows that the propfan designs are suitable for the wind-tunnel test and confirms that the propfans should be flutter-free under the range of conditions of the testing.

Design and test of an automated version of the modified Jebsen test of hand function using Microsoft Kinect.

PubMed

Simonsen, Daniel; Nielsen, Ida F; Spaich, Erika G; Andersen, Ole K

2017-05-02

The present paper describes the design and evaluation of an automated version of the Modified Jebsen Test of Hand Function (MJT) based on the Microsoft Kinect sensor. The MJT was administered twice to 11 chronic stroke subjects with varying degrees of hand function deficits. The test times of the MJT were evaluated manually by a therapist using a stopwatch, and automatically using the Microsoft Kinect sensor. The ground truth times were assessed based on inspection of the video-recordings. The agreement between the methods was evaluated along with the test-retest performance. The results from Bland-Altman analysis showed better agreement between the ground truth times and the automatic MJT time evaluations compared to the agreement between the ground truth times and the times estimated by the therapist. The results from the test-retest performance showed that the subjects significantly improved their performance in several subtests of the MJT, indicating a practice effect. The results from the test showed that the Kinect can be used for automating the MJT.

Full-Scale Test and Analysis Results of a PRSEUS Fuselage Panel to Assess Damage Containment Features

NASA Technical Reports Server (NTRS)

Bergan, Andrew; Bakuckas, John G., Jr.; Lovejoy, Andrew; Jegley, Dawn; Linton, Kim; Neal, Bert; Korkosz, Gregory; Awerbuch, Jonathan; Tan, Tein-Min

2012-01-01

Integrally stitched composite technology is an area that shows promise in enhancing the structural integrity of aircraft and aerospace structures. The most recent generation of this technology is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. The goal of the PRSEUS concept relevant to this test is to provide damage containment capability for composite structures while reducing overall structural weight. The National Aeronautics and Space Administration (NASA), the Federal Aviation Administration (FAA), and The Boeing Company have partnered in an effort to assess the damage containment features of a full-scale curved PRSEUS panel using the FAA Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility. A single PRSEUS test panel was subjected to axial tension, internal pressure, and combined axial tension and internal pressure loads. The test results showed excellent performance of the PRSEUS concept. No growth of Barely Visible Impact Damage (BVID) was observed after ultimate loads were applied. With a two-bay notch severing the central stringer, damage was contained within the two-bay region well above the required limit load conditions. Catastrophic failure was well above the ultimate load level. Information describing the test panel and procedure has been previously presented, so this paper focuses on the experimental procedure, test results, nondestructive inspection results, and preliminary test and analysis correlation.

The Evaluation of Damage Effects on MgO Added Concrete with Slag Cement Exposed to Calcium Chloride Deicing Salt.

PubMed

Jang, Jae-Kyeong; Kim, Hong-Gi; Kim, Jun-Hyeong; Ryou, Jae-Suk

2018-05-14

Concrete systems exposed to deicers are damaged in physical and chemical ways. In mitigating the damage from CaCl₂ deicers, the usage of ground slag cement and MgO are investigated. Ordinary Portland cement (OPC) and slag cement are used in different proportions as the binding material, and MgO in doses of 0%, 5%, 7%, and 10% are added to the systems. After 28 days of water-curing, the specimens are immersed in 30% CaCl₂ solution by mass for 180 days. Compressive strength test, carbonation test, chloride penetration test, chloride content test, XRD analysis, and SEM-EDAX analysis are conducted to evaluate the damage effects of the deicing solution. Up to 28 days, plain specimens with increasing MgO show a decrease in compressive strength, an increase in carbonation resistance, and a decrease in chloride penetration resistance, whereas the S30- and S50- specimens show a slight increase in compressive strength, an increase in carbonation resistance, and a slight increase in chloride penetration resistance. After 180 days of immersion in deicing solution, specimens with MgO retain their compressive strength longer and show improved durability. Furthermore, the addition of MgO to concrete systems with slag cement induces the formation of magnesium silicate hydrate (M-S-H) phases.

Zebrafish Embryo as an In Vivo Model for Behavioral and Pharmacological Characterization of Methylxanthine Drugs.

PubMed

Basnet, Ram Manohar; Guarienti, Michela; Memo, Maurizio

2017-03-09

Zebrafish embryo is emerging as an important tool for behavior analysis as well as toxicity testing. In this study, we compared the effect of nine different methylxanthine drugs using zebrafish embryo as a model. We performed behavioral analysis, biochemical assay and Fish Embryo Toxicity (FET) test in zebrafish embryos after treatment with methylxanthines. Each drug appeared to behave in different ways and showed a distinct pattern of results. Embryos treated with seven out of nine methylxanthines exhibited epileptic-like pattern of movements, the severity of which varied with drugs and doses used. Cyclic AMP measurement showed that, despite of a significant increase in cAMP with some compounds, it was unrelated to the observed movement behavior changes. FET test showed a different pattern of toxicity with different methylxanthines. Each drug could be distinguished from the other based on its effect on mortality, morphological defects and teratogenic effects. In addition, there was a strong positive correlation between the toxic doses (TC 50 ) calculated in zebrafish embryos and lethal doses (LD 50 ) in rodents obtained from TOXNET database. Taken together, all these findings elucidate the potentiality of zebrafish embryos as an in vivo model for behavioral and toxicity testing of methylxanthines and other related compounds.

Developmental toxicity, acute toxicity and mutagenicity testing in freshwater snails Biomphalaria glabrata (Mollusca: Gastropoda) exposed to chromium and water samples.

PubMed

Tallarico, Lenita de Freitas; Borrely, Sueli Ivone; Hamada, Natália; Grazeffe, Vanessa Siqueira; Ohlweiler, Fernanda Pires; Okazaki, Kayo; Granatelli, Amanda Tosatte; Pereira, Ivana Wuo; Pereira, Carlos Alberto de Bragança; Nakano, Eliana

2014-12-01

A protocol combining acute toxicity, developmental toxicity and mutagenicity analysis in freshwater snail Biomphalaria glabrata for application in ecotoxicological studies is described. For acute toxicity testing, LC50 and EC50 values were determined; dominant lethal mutations induction was the endpoint for mutagenicity analysis. Reference toxicant potassium dichromate (K2Cr2O7) was used to characterize B. glabrata sensitivity for toxicity and cyclophosphamide to mutagenicity testing purposes. Compared to other relevant freshwater species, B. glabrata showed high sensitivity: the lowest EC50 value was obtained with embryos at veliger stage (5.76mg/L). To assess the model applicability for environmental studies, influent and effluent water samples from a wastewater treatment plant were evaluated. Gastropod sensitivity was assessed in comparison to the standardized bioassay with Daphnia similis exposed to the same water samples. Sampling sites identified as toxic to daphnids were also detected by snails, showing a qualitatively similar sensitivity suggesting that B. glabrata is a suitable test species for freshwater monitoring. Holding procedures and protocols implemented for toxicity and developmental bioassays showed to be in compliance with international standards for intra-laboratory precision. Thereby, we are proposing this system for application in ecotoxicological studies. Copyright © 2014 Elsevier Inc. All rights reserved.

Analytical and Experimental Verification of a Flight Article for a Mach-8 Boundary-Layer Experiment

NASA Technical Reports Server (NTRS)

Richards, W. Lance; Monaghan, Richard C.

1996-01-01

Preparations for a boundary-layer transition experiment to be conducted on a future flight mission of the air-launched Pegasus(TM) rocket are underway. The experiment requires a flight-test article called a glove to be attached to the wing of the Mach-8 first-stage booster. A three-dimensional, nonlinear finite-element analysis has been performed and significant small-scale laboratory testing has been accomplished to ensure the glove design integrity and quality of the experiment. Reliance on both the analysis and experiment activities has been instrumental in the success of the flight-article design. Results obtained from the structural analysis and laboratory testing show that all glove components are well within the allowable thermal stress and deformation requirements to satisfy the experiment objectives.

Frequency analysis and its spatiotemporal characteristics of precipitation extreme events in China during 1951-2010

NASA Astrophysics Data System (ADS)

Shao, Yuehong; Wu, Junmei; Ye, Jinyin; Liu, Yonghe

2015-08-01

This study investigates frequency analysis and its spatiotemporal characteristics of precipitation extremes based on annual maximum of daily precipitation (AMP) data of 753 observation stations in China during the period 1951-2010. Several statistical methods including L-moments, Mann-Kendall test (MK test), Student's t test ( t test) and analysis of variance ( F-test) are used to study different statistical properties related to frequency and spatiotemporal characteristics of precipitation extremes. The results indicate that the AMP series of most sites have no linear trends at 90 % confidence level, but there is a distinctive decrease trend in Beijing-Tianjin-Tangshan region. The analysis of abrupt changes shows that there are no significant changes in most sites, and no distinctive regional patterns within the mutation sites either. An important innovation different from the previous studies is the shift in the mean and the variance which are also studied in this paper in order to further analyze the changes of strong and weak precipitation extreme events. The shift analysis shows that we should pay more attention to the drought in North China and to the flood control and drought in South China, especially to those regions that have no clear trend and have a significant shift in the variance. More important, this study conducts the comprehensive analysis of a complete set of quantile estimates and its spatiotemporal characteristic in China. Spatial distribution of quantile estimation based on the AMP series demonstrated that the values gradually increased from the Northwest to the Southeast with the increment of duration and return period, while the increasing rate of estimation is smooth in the arid and semiarid region and is rapid in humid region. Frequency estimates of 50-year return period are in agreement with the maximum observations of AMP series in the most stations, which can provide more quantitative and scientific basis for decision making.

An Experimental Study of Launch Vehicle Propellant Tank Fragmentation

NASA Technical Reports Server (NTRS)

Richardson, Erin; Jackson, Austin; Hays, Michael; Bangham, Mike; Blackwood, James; Skinner, Troy; Richman, Ben

2014-01-01

In order to better understand launch vehicle abort environments, Bangham Engineering Inc. (BEi) built a test assembly that fails sample materials (steel and aluminum plates of various alloys and thicknesses) under quasi-realistic vehicle failure conditions. Samples are exposed to pressures similar to those expected in vehicle failure scenarios and filmed at high speed to increase understanding of complex fracture mechanics. After failure, the fragments of each test sample are collected, catalogued and reconstructed for further study. Post-test analysis shows that aluminum samples consistently produce fewer fragments than steel samples of similar thickness and at similar failure pressures. Video analysis shows that there are several failure 'patterns' that can be observed for all test samples based on configuration. Fragment velocities are also measured from high speed video data. Sample thickness and material are analyzed for trends in failure pressure. Testing is also done with cryogenic and noncryogenic liquid loading on the samples. It is determined that liquid loading and cryogenic temperatures can decrease material fragmentation for sub-flight thicknesses. A method is developed for capture and collection of fragments that is greater than 97 percent effective in recovering sample mass, addressing the generation of tiny fragments. Currently, samples tested do not match actual launch vehicle propellant tank material thicknesses because of size constraints on test assembly, but test findings are used to inform the design and build of another, larger test assembly with the purpose of testing actual vehicle flight materials that include structural components such as iso-grid and friction stir welds.

SSME seal test program: Test results for smooth, hole-pattern and helically-grooved stators

NASA Technical Reports Server (NTRS)

Childs, Dara W.

1987-01-01

All of the listed seals were tested in a liquid Halon test facility at high Reynolds numbers. In addition, a helically-grooved-stator seal was tested in an air seal facility. An analysis of the test results with comparisons to theoretical predictions supports the following conclusions: (1) For small seals, the Hirs' friction-factor model is more restricted than had been thought; (2) For smooth seals, predictions of stiffness and damping improve markedly as the radical clearance is reduced; (3) Friction-factor data for hole-pattern-seal stators frequently deviates from the Hirs model; (4) Predictions of stiffness and damping coefficients for hole-pattern-stator seals is generally reasonable; (5) Tests for the hole-pattern stators at reduced clearances show no clear optimum for hole-pattern seals with respect to either hole-area ratio or hole depth to minimum clearance ratios; (6) Tests of these hole-pattern stators show no significant advantage in net damping over smooth seals; (7) Tests of helically-grooved seal stators in Halon show reasonable agreement between theory and prediction for leakage and direct stiffness but poor agreement for the net damping coefficient.

Determination of elastic modulus of ceramics using ultrasonic testing

NASA Astrophysics Data System (ADS)

Sasmita, Firmansyah; Wibisono, Gatot; Judawisastra, Hermawan; Priambodo, Toni Agung

2018-04-01

Elastic modulus is important material property on structural ceramics application. However, bending test as a common method for determining this property require particular specimen preparation. Furthermore, elastic modulus of ceramics could vary because it depends on porosity content. For structural ceramics industry, such as ceramic tiles, this property is very important. This drives the development of new method to improve effectivity or verification method as well. In this research, ultrasonic testing was conducted to determine elastic modulus of soda lime glass and ceramic tiles. The experiment parameter was frequency of probe (1, 2, 4 MHz). Characterization of density and porosity were also done for analysis. Results from ultrasonic testing were compared with elastic modulus resulted from bending test. Elastic modulus of soda-lime glass based on ultrasonic testing showed excellent result with error 2.69% for 2 MHz probe relative to bending test result. Testing on red and white ceramic tiles were still contained error up to 41% and 158%, respectively. The results for red ceramic tile showed trend that 1 MHz probe gave better accuracy in determining elastic modulus. However, testing on white ceramic tile showed different trend. It was due to the presence of porosity and near field effect.

Temporary Thermocouple Attachment for Thermal/Vacuum Testing at Non-Extreme Temperatures - Test Results

NASA Technical Reports Server (NTRS)

Wright, Sarah E.; Ungar, Eugene K.

2017-01-01

Post-test examination and data analysis that followed a two week long vacuum test showed that numerous self-stick thermocouples became detached from the test article. The thermocouples were reattached with thermally conductive epoxy and the test was repeated to obtain the required data. Because the thermocouple detachment resulted in significant expense and rework, it was decided to investigate the temporary attachment methods used around NASA and to perform a test to assess their efficacy. The present work describes the testing that was performed in early and mid-2017. The test article and the temporary thermocouple attachment methods tested are described. During the first test, fully half of the thermocouples detached - although the detachment showed subtly in the data for some. The second test was performed to confirm the data from the first test and to investigate the effect of test article and thermocouple grounding. The results of the testing over temperatures ranging from -150 to 200degF are detailed and preliminary recommendations are made for temporary thermocouple attachment methods.

Spotting Incorrect Rules in Signed-Number Arithmetic by the Individual Consistency Index.

DTIC Science & Technology

1981-08-01

meaning of dimensionality of achievement data. It also shows the importance of construct validity, even in criterion referenced testing of the cognitive ... aspect of performance, and that the traditional means of item analysis that are based on taking the variances of binary scores and content analysis

Orthostatic Intolerance and Postural Orthostatic Tachycardia Syndrome in Joint Hypermobility Syndrome/Ehlers-Danlos Syndrome, Hypermobility Type: Neurovegetative Dysregulation or Autonomic Failure?

PubMed

Celletti, Claudia; Camerota, Filippo; Castori, Marco; Censi, Federica; Gioffrè, Laura; Calcagnini, Giovanni; Strano, Stefano

2017-01-01

Background . Joint hypermobility syndrome/Ehlers-Danlos syndrome, hypermobility type (JHS/EDS-HT), is a hereditary connective tissue disorder mainly characterized by generalized joint hypermobility, skin texture abnormalities, and visceral and vascular dysfunctions, also comprising symptoms of autonomic dysfunction. This study aims to further evaluate cardiovascular autonomic involvement in JHS/EDS-HT by a battery of functional tests. Methods . The response to cardiovascular reflex tests comprising deep breathing, Valsalva maneuver, 30/15 ratio, handgrip test, and head-up tilt test was studied in 35 JHS/EDS-HT adults. Heart rate and blood pressure variability was also investigated by spectral analysis in comparison to age and sex healthy matched group. Results . Valsalva ratio was normal in all patients, but 37.2% of them were not able to finish the test. At tilt, 48.6% patients showed postural orthostatic tachycardia, 31.4% orthostatic intolerance, 20% normal results. Only one patient had orthostatic hypotension. Spectral analysis showed significant higher baroreflex sensitivity values at rest compared to controls. Conclusions. This study confirms the abnormal cardiovascular autonomic profile in adults with JHS/EDS-HT and found the higher baroreflex sensitivity as a potential disease marker and clue for future research.

Effect of Microstructure on the Mechanical Properties of Extruded Magnesium and a Magnesium Alloy

NASA Astrophysics Data System (ADS)

McGhee, Paul

The main objective of this research was to investigate the relationship between the fatigue behavior and crystallographic texture evolution of magnesium (Mg) alloys with a range of microalloying element content processed under various extrusion conditions. Several Mg alloys were processed under a range of extrusion temperatures, extrusion ratios, and alloying content and tested under monotonic and cyclic fatigue loading conditions: fully-reversed condition tested at strain amplitudes of 0.15% - 1.00% in strain-control mode. After fatigue testing, Mg microstructural analysis was performed using SEM, TEM, optical microscopy, and X-ray diffraction techniques. Microstructural observations revealed significant grain refinement through a combination of zirconium (Zr) addition and hot-extrusion, producing fine equiaxed grain structure with grain sizes ranging between 1-5 microm. Texture analysis and partial compression testing results showed that the initial texture of the extruded alloy gradually evolved upon compressive loading along the c-axes inducing extension twinning creating a strong basal texture along the extrusion direction. Full tensile and compression testing at room temperature showed that the combination of hot extrusion and Zr addition can further refine the grains of the Mg alloys microstructure and enhance the texture while simultaneously enhancing the mechanical properties.

A study of correlations between crude oil spot and futures markets: A rolling sample test

NASA Astrophysics Data System (ADS)

Liu, Li; Wan, Jieqiu

2011-10-01

In this article, we investigate the asymmetries of exceedance correlations and cross-correlations between West Texas Intermediate (WTI) spot and futures markets. First, employing the test statistic proposed by Hong et al. [Asymmetries in stock returns: statistical tests and economic evaluation, Review of Financial Studies 20 (2007) 1547-1581], we find that the exceedance correlations were overall symmetric. However, the results from rolling windows show that some occasional events could induce the significant asymmetries of the exceedance correlations. Second, employing the test statistic proposed by Podobnik et al. [Quantifying cross-correlations using local and global detrending approaches, European Physics Journal B 71 (2009) 243-250], we find that the cross-correlations were significant even for large lagged orders. Using the detrended cross-correlation analysis proposed by Podobnik and Stanley [Detrended cross-correlation analysis: a new method for analyzing two nonstationary time series, Physics Review Letters 100 (2008) 084102], we find that the cross-correlations were weakly persistent and were stronger between spot and futures contract with larger maturity. Our results from rolling sample test also show the apparent effects of the exogenous events. Additionally, we have some relevant discussions on the obtained evidence.

Sensitivity and specificity of eustachian tube function tests in adults.

PubMed

Doyle, William J; Swarts, J Douglas; Banks, Julianne; Casselbrant, Margaretha L; Mandel, Ellen M; Alper, Cuneyt M

2013-07-01

The study demonstrates the utility of eustachian tube (ET) function (ETF) test results for accurately assigning ears to disease state. To determine if ETF tests can identify ears with physician-diagnosed ET dysfunction (ETD) in a mixed population at high sensitivity and specificity and to define the interrelatedness of ETF test parameters. Through use of the forced-response, inflation-deflation, Valsalva, and sniffing tests, ETF was evaluated in 15 control ears of adult subjects after unilateral myringotomy (group 1) and in 23 ears of 19 adult subjects with ventilation tubes inserted for ETD (group 2). Data were analyzed using logistic regression including each parameter independently and then a step-down discriminant analysis including all ETF test parameters to predict group assignment. Factor analysis operating over all parameters was used to explore relatedness. ETF testing. ETF parameters for the forced response, inflation-deflation, Valsalva, and sniffing tests measured in 15 control ears of adult subjects after unilateral myringotomy (group 1) and in 23 ears of 19 adult subjects with ventilation tubes inserted for ETD (group 2). The discriminant analysis identified 4 ETF test parameters (Valsalva, ET opening pressure, dilatory efficiency, and percentage of positive pressure equilibrated) that together correctly assigned ears to group 2 at a sensitivity of 95% and a specificity of 83%. Individual parameters representing the efficiency of ET opening during swallowing showed moderately accurate assignments of ears to their respective groups. Three factors captured approximately 98% of the variance among parameters: the first had negative loadings of the ETF structural parameters; the second had positive loadings of the muscle-assisted ET opening parameters; and the third had negative loadings of the muscle-assisted ET opening parameters and positive loadings of the structural parameters. These results show that ETF tests can correctly assign individual ears to physician-diagnosed ETD with high sensitivity and specificity and that ETF test parameters can be grouped into structural-functional categories.

The prognostic value of tumor-infiltrating neutrophils in gastric adenocarcinoma after resection.

PubMed

Zhao, Jing-jing; Pan, Ke; Wang, Wei; Chen, Ju-gao; Wu, Yan-heng; Lv, Lin; Li, Jian-jun; Chen, Yi-bing; Wang, Dan-dan; Pan, Qiu-zhong; Li, Xiao-dong; Xia, Jian-chuan

2012-01-01

Several pieces of evidence indicate that tumor-infiltrating neutrophils (TINs) are correlated to tumor progression. In the current study, we explore the relationship between TINs and clinicopathological features of gastric adenocarcinoma patients. Furthermore, we investigated the prognostic value of TINs. The study was comprised of two groups, training group (115 patients) and test group (97 patients). Biomarkers (intratumoral CD15+ neutrophils) were assessed by immunohistochemistry. The relationship between clinicopathological features and patient outcome were evaluated using Cox regression and Kaplan-Meier analysis. Immunohistochemical detection showed that the tumor-infiltrating neutrophils (TINs) in the training group ranged from 0.00-115.70 cells/high-power microscopic field (HPF) and the median number was 21.60 cells/HPF. Based on the median number, the patients were divided into high and low TINs groups. Chi-square test analysis revealed that the density of CD15+ TINs was positively associated with lymph node metastasis (p = 0.024), distance metastasis (p = 0.004) and UICC (International Union Against Cancer) staging (p = 0.028). Kaplan-Meier analysis showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.002). Multivariate Cox's analysis showed that the density of CD15+ TINs was an independent prognostic factor for overall survival of gastric adenocarcinoma patients. Using another 97 patients as a test group and basing on the median number of TINs (21.60 cells/HPF) coming from the training group, Kaplan-Meier analysis also showed that patients with a lower density of TINs had a better prognosis than patients with a higher density of TINs (p = 0.032). The results verify that the number of CD15+ TINs can predict the survival of gastric adenocarcinoma surgical patients. The presence of CD15+ TINs is an independent and unfavorable factor in the prognosis of gastric adenocarcinoma patients. Targeting CD15+ TINs may be a potential intervenient therapy in the future.

Using Item Response Theory to Describe the Nonverbal Literacy Assessment (NVLA)

ERIC Educational Resources Information Center

Fleming, Danielle; Wilson, Mark; Ahlgrim-Delzell, Lynn

2018-01-01

The Nonverbal Literacy Assessment (NVLA) is a literacy assessment designed for students with significant intellectual disabilities. The 218-item test was initially examined using confirmatory factor analysis. This method showed that the test worked as expected, but the items loaded onto a single factor. This article uses item response theory to…

Assessing the Usefulness of SAT and ACT Tests in Minority Admissions

ERIC Educational Resources Information Center

Micceri, Theodore

2010-01-01

This study sought to determine whether the use of standardized test scores contributes any useful information regarding First Time in College (FTIC) students' probable success at USF, using more detailed analysis of underrepresented minorities and women, who Micceri (2009) shows, experience substantial negative bias relative to males and whites on…

A Comparison of Two Tests for the Significance of a Mean Vector.

DTIC Science & Technology

1978-01-01

rejected as soon as a component test in the sequence shows significance . It is well. known (3’. Roy 1958; Roy, Gnanadesikan and Srivastava 1971 (p...confidence bounds ” , Annals of Mathematical Statistics, 29, 491—503. (14] Roy, S.N., Gnanadesikan , R., and Srivastava, J.N. (1971). Analysis and

[Transcultural adaptation of the Antifat Attitudes Test to Brazilian Portuguese].

PubMed

Obara, Angélica Almeida; Alvarenga, Marle Dos Santos

2018-05-01

Obese individuals are often blamed for their own condition and the targets of discrimination and prejudice. The scope of this study is to describe the cross-cultural adaptation to Brazilian Portuguese and the validation of the Antifat Attitudes Test - specifically developed for evaluation of negative attitudes toward the obese individual. The scale has 34 statements distributed in three subscales - Social/Character Disparagement (15 items), Physical/Romantic Unattractiveness (10 items) and Weight Control/Blame (9 items). The method involved the translation of the scale; evaluation of the conceptual, operational and item equivalence; evaluation of the semantic equivalence using the paired t test, the Pearson correlation coefficient and the intraclass correlation coefficient (ICC); internal consistency evaluation (Cronbach's alpha) and test-retest reliability (ICC) and Confirmatory Factor Analysis - after application in 340 college students in the area of health. The results showed good global internal consistency and reliability (α 0.85; CCI 0.83), and factor analysis showed that the original subscales can be kept in the adaptation, and therefore the scale adapted to the Brazilian-Portuguese version is valid and useful in studies to explore negative attitudes toward obese individuals.

PEPA test: fast and powerful differential analysis from relative quantitative proteomics data using shared peptides.

PubMed

Jacob, Laurent; Combes, Florence; Burger, Thomas

2018-06-18

We propose a new hypothesis test for the differential abundance of proteins in mass-spectrometry based relative quantification. An important feature of this type of high-throughput analyses is that it involves an enzymatic digestion of the sample proteins into peptides prior to identification and quantification. Due to numerous homology sequences, different proteins can lead to peptides with identical amino acid chains, so that their parent protein is ambiguous. These so-called shared peptides make the protein-level statistical analysis a challenge and are often not accounted for. In this article, we use a linear model describing peptide-protein relationships to build a likelihood ratio test of differential abundance for proteins. We show that the likelihood ratio statistic can be computed in linear time with the number of peptides. We also provide the asymptotic null distribution of a regularized version of our statistic. Experiments on both real and simulated datasets show that our procedures outperforms state-of-the-art methods. The procedures are available via the pepa.test function of the DAPAR Bioconductor R package.

On the Infrasound Detected From The 2013 and 2016 DPRK's Underground Nuclear Tests

NASA Astrophysics Data System (ADS)

Assink, J. D.; Averbuch, G.; Smets, P. S. M.; Evers, L. G.

2016-12-01

The underground nuclear tests by the Democratic People's Republic of Korea (DPRK) generated atmospheric infrasound both in 2013 and 2016. Clear detections were made in the Russian Federation (I45RU) and Japan (I30JP) in 2013 at stations from the International Monitoring System. Both tropospheric and stratospheric refractions arrived at the stations. In 2016, only a weak return was potentially observed at I45RU. Data analysis and propagation modeling show that the noise level at the stations and the stratospheric circumpolar vortex were different in 2016 compared to 2013. A seismo-acoustic analysis of the 2013 and 2016 DPRK tests, in combination with atmospheric propagation modeling, motivates the hypothesis that the 2016 test was at a greater depth than the 2013 test. In such a case, less seismic energy would couple through the lithosphere-atmosphere interface, leading to less observable infrasound. A preliminary analysis suggests that the 2016 test occurred at least 1.5 times deeper. Since explosion depth is difficult to estimate from seismic data alone, this motivates a synergy between seismics and infrasonics.

Screening for colon cancer: A test for occult blood.

PubMed

Khakimov, N; Khasanova, G; Ershova, K; Gibadullina, L; Vetkina, T; Lobisheva, G; Chumakova, A

2015-01-01

The relevance of the problem of colorectal cancer (CRC) is evident because of extremely high morbidity and mortality rates, associated with this disease. CRC is mostly diagnosed only at very advanced stages. The reduction of mortality can be achieved by the popularization of screening-methods for early identification of CRC and adenomatous polyps of the colon, which are proved to be precancerous condition. Fecal occult blood test is a well-known method of screening for CRC. The advantages of this method when compared, for example, with colonoscopy are its simplicity and cost-effectiveness.Two techniques are usually used for detection of occult blood in the stool: Hemoccult (Guaiac) test and immunochemical test for hemoglobin. There is no consensus among researchers regarding the validity of these tests for the diagnosis of colorectal cancer. For example, J.S. Mandel (1996) notes 60% sensitivity of Guaiac-test for the detection of the early forms of colorectal cancer, while O.I. Kit (2014) suggets that it is not higher than 30%. There are also various opinions about specificity of these two tests. To review the literature on the validity of the fecal occult blood tests for the diagnosis of CRC. We looked for articles (electronic versions) available for free in the full-text versions, published from June 1, 1990 to December 31, 2014 in Russian or English. The following databases were used for search: E-LIBRARY; Cochrane; MEDLINE; EMBASE; Google search. Only original research papers were analyzed. Literature reviews or systematic reviews were not taken for analyses. 1) use of Guaiac and/or immunochemical fecal occult blood test as screening-tests for the detection of colorectal cancer and/or colon polyps (1 cm or more in diameter) in people older than 45 years; 2) comparing of results with the results of colonoscopy (colonoscopy is counted by majority of the authors as a "gold standard" for the diagnosis of CRC and adenomatous polyps). Initial keyword search returned 803 000 results, of which 449 sources were selected. After reading the abstracts, 29 articles that met inclusion criteria were kept. 10 other articles were excluded after that because they did not contain enough data for extraction or did not contain a control group. At the final step 19 articles were used for meta-analysis.Forest plot and Rock curve, which were developed with inclusion of the data from all studies, showed heterogeneity of the data. Additional analyzes were performed in subgroups with different diagnoses and various tests.The sensitivity of the Guaiac test for the diagnosis of colorectal cancer varied from 0.13 to 1.00, and specificity - from 0.69 to 0.99. The sensitivity of the immunochemical test for the diagnosis of CRC ranged from 0.42 to 0.94 with specificity ranging from 0.40 to 1.00.The sensitivity of the Guaiac test for the diagnosis of the colon polyps was between 0.05 and 0.69, and its specificity - from 0.67 to 0.98. The sensitivity of the immunochemical test for the diagnosis of polyps was from 0.24 to 0.75, and its specificity - from 0.40 to 0.97.Bivariate analysis of the validity of Guaiac test and immunochemical method for the diagnosis of colorectal cancer showed better results for the immunochemical test compared to Guaiac test. The tests showed very similar results when used for the diagnosis of polyposis. Bivariate analysis, comparing the validity of tests for the diagnosis of colorectal cancer versus polyposis demonstrated better results for CRC.Multivariate analysis of the validity of the Guaiac and immunochemical tests for the diagnosis of colorectal cancer and polyps also showed better results for detection of colorectal cancer compared with the polyps for both tests. At the same time the highest validity for the diagnosis of CRC was demonstrated for immunochemical analysis. 1. The sensitivity of the Guaiac test for occult blood in stool is lower than its specificity.2. Broad dispersion of the validity characteristics of the fecal occult blood tests was observed.3. The validity of tests for occult blood was higher when they were used for detection of colorectal cancer than of colon polyposis.4. The highest validity rate has been demonstrated for the immunochemical test when it was used for colon cancer screening.

A cost effectiveness analysis of thiopurine methyltransferase testing for guiding 6-mercaptopurine dosing in children with acute lymphoblastic leukemia.

PubMed

Donnan, Jennifer R; Ungar, Wendy J; Mathews, Maria; Hancock-Howard, Rebecca L; Rahman, Proton

2011-08-01

An increased understanding of the genetic basis of disease creates a demand for personalized medicine and more genetic testing for diagnosis and treatment. The objective was to assess the incremental cost-effectiveness per life-month gained of thiopurine methyltransferase (TPMT) genotyping to guide doses of 6-mercaptopurine (6-MP) in children with acute lymphoblastic leukemia (ALL) compared to enzymatic testing and standard weight-based dosing. A cost-effectiveness analysis was conducted from a health care system perspective comparing costs and consequences over 3 months. Decision analysis was used to evaluate the impact of TPMT tests on preventing myelosuppression and improving survival in ALL patients receiving 6-MP. Direct medical costs included laboratory tests, medications, physician services, pharmacy and inpatient care. Probabilities were derived from published evidence. Survival was measured in life-months. The robustness of the results to variable uncertainty was tested in one-way sensitivity analyses. Probabilistic sensitivity analysis examined the impact of parameter uncertainty and generated confidence intervals around point estimates. Neither of the testing interventions showed a benefit in survival compared to weight-based dosing. Both test strategies were more costly compared to weight-based dosing. Incremental costs per child (95% confidence interval) were $277 ($112, $442) and $298 ($392, $421) for the genotyping and phenotyping strategies, respectively, compared to weight-based dosing. The present analysis suggests that screening for TPMT mutations using either genotype or enzymatic laboratory tests prior to the administration of 6-MP in pediatric ALL patients is not cost-effective. Copyright © 2011 Wiley-Liss, Inc.

Nonlinear Whirl Response of a High-Speed Seal Test Rotor With Marginal and Extended Squeeze-Film Dampers

NASA Technical Reports Server (NTRS)

Proctor, Margaret P.; Gunter, Edgar J.

2005-01-01

Synchronous and nonsynchronous whirl response analysis of a double overhung, high-speed seal test rotor with ball bearings supported in 5.84- and 12.7-mm-long, un-centered squeeze-film oil dampers is presented. Test performance with the original damper of length 5.84 mm was marginal, with nonsynchronous whirling at the overhung seal test disk and high amplitude synchronous response above 32,000 rpm near the drive spline section occurring. A system critical speed analysis of the drive system and the high-speed seal test rotor indicated that the first two critical speeds are associated with the seal test rotor. Nonlinear synchronous unbalance and time transient whirl studies were conducted on the seal test rotor with the original and extended damper lengths. With the original damper design, the nonlinear synchronous response showed that unbalance could cause damper lockup at 33,000 rpm. Alford cross-coupling forces were also included at the overhung seal test disk for the whirl analysis. Sub-synchronous whirling at the seal test disk was observed in the nonlinear time transient analysis. With the extended damper length of 12.7 mm, the sub-synchronous motion was eliminated and the rotor unbalance response was acceptable to 45,000 rpm with moderate rotor unbalance. However, with high rotor unbalance, damper lockup could still occur at 33,000 rpm, even with the extended squeeze-film dampers. Therefore, the test rotor must be reasonably balanced in order for the un-centered dampers to be effective.

Development of small scale cluster computer for numerical analysis

NASA Astrophysics Data System (ADS)

Zulkifli, N. H. N.; Sapit, A.; Mohammed, A. N.

2017-09-01

In this study, two units of personal computer were successfully networked together to form a small scale cluster. Each of the processor involved are multicore processor which has four cores in it, thus made this cluster to have eight processors. Here, the cluster incorporate Ubuntu 14.04 LINUX environment with MPI implementation (MPICH2). Two main tests were conducted in order to test the cluster, which is communication test and performance test. The communication test was done to make sure that the computers are able to pass the required information without any problem and were done by using simple MPI Hello Program where the program written in C language. Additional, performance test was also done to prove that this cluster calculation performance is much better than single CPU computer. In this performance test, four tests were done by running the same code by using single node, 2 processors, 4 processors, and 8 processors. The result shows that with additional processors, the time required to solve the problem decrease. Time required for the calculation shorten to half when we double the processors. To conclude, we successfully develop a small scale cluster computer using common hardware which capable of higher computing power when compare to single CPU processor, and this can be beneficial for research that require high computing power especially numerical analysis such as finite element analysis, computational fluid dynamics, and computational physics analysis.

Improved Sectional Image Analysis Technique for Evaluating Fiber Orientations in Fiber-Reinforced Cement-Based Materials.

PubMed

Lee, Bang Yeon; Kang, Su-Tae; Yun, Hae-Bum; Kim, Yun Yong

2016-01-12

The distribution of fiber orientation is an important factor in determining the mechanical properties of fiber-reinforced concrete. This study proposes a new image analysis technique for improving the evaluation accuracy of fiber orientation distribution in the sectional image of fiber-reinforced concrete. A series of tests on the accuracy of fiber detection and the estimation performance of fiber orientation was performed on artificial fiber images to assess the validity of the proposed technique. The validation test results showed that the proposed technique estimates the distribution of fiber orientation more accurately than the direct measurement of fiber orientation by image analysis.

Investigations of Air-cooled Turbine Rotors for Turbojet Engines II : Mechanical Design, Stress Analysis, and Burst Test of Modified J33 Split-disk Rotor / Richard H. Kemp and Merland L. Moseson

NASA Technical Reports Server (NTRS)

Kemp, Richard H; Moseson, Merland L

1952-01-01

A full-scale J33 air-cooled split turbine rotor was designed and spin-pit tested to destruction. Stress analysis and spin-pit results indicated that the rotor in a J33 turbojet engine, however, showed that the rear disk of the rotor operated at temperatures substantially higher than the forward disk. An extension of the stress analysis to include the temperature difference between the two disks indicated that engine modifications are required to permit operation of the two disks at more nearly the same temperature level.

Improved Sectional Image Analysis Technique for Evaluating Fiber Orientations in Fiber-Reinforced Cement-Based Materials

PubMed Central

Lee, Bang Yeon; Kang, Su-Tae; Yun, Hae-Bum; Kim, Yun Yong

2016-01-01

The distribution of fiber orientation is an important factor in determining the mechanical properties of fiber-reinforced concrete. This study proposes a new image analysis technique for improving the evaluation accuracy of fiber orientation distribution in the sectional image of fiber-reinforced concrete. A series of tests on the accuracy of fiber detection and the estimation performance of fiber orientation was performed on artificial fiber images to assess the validity of the proposed technique. The validation test results showed that the proposed technique estimates the distribution of fiber orientation more accurately than the direct measurement of fiber orientation by image analysis. PMID:28787839

Achievement Testing with the Wechsler Quicktest: An Examination of Its Psychometric Properties and Applied Utility with a Greek-Cypriot Sample

ERIC Educational Resources Information Center

Vrachimi-Souroulla, Andry; Panayiotou, Georgia; Kokkinos, Constantinos M.; Lamprianou, Iasonas

2011-01-01

The study aimed to field-test a Greek version of the Wechsler Quicktest and to examine its psychometric properties. The Quicktest was individually administered to 208 students, aged 5-14 years, along with a reading test. Based on the Rasch analysis, data for the Quicktest subtests showed acceptable fit to the model. Also, correlations were found…

Progress toward the 95 Goal, 2001. Measuring Up. E&R Report.

ERIC Educational Resources Information Center

Wake County Public School System, Raleigh, NC. Dept. of Evaluation and Research.

In August 1998, the Wake County Board of Education, North Carolina, adopted the goal that by 2003, 95% of students tested would be at or above grade level as measured by the North Carolina End-of-Grade (EOG) testing at grades 3 and 8 bye the year 2003. This report provides an analysis of EOG test results for the 2000-2001 academic year to show how…

Contact dermatitis caused by a new rubber compound detected in canvas shoes.

PubMed

Hulstaert, Eva; Bergendorff, Ola; Persson, Christina; Goossens, An; Gilissen, Liesbeth; Engfeldt, Malin; Bruze, Magnus; Schuttelaar, Marie L; Meijer, Joost M; Lapeere, Hilde

2018-01-01

In 2015 and 2016, female patients in Flanders consulted a dermatologist because they developed skin lesions after wearing a specific brand of canvas shoes. To identify the culprit allergen in the shoes. Eighteen young females aged 14-22 years presented with itching and erythematous to purple-coloured eczematous lesions on both feet. They were patch tested by 10 dermatologists with the European baseline series. Some patients underwent testing with additional series. Pieces of the shoe fabrics were tested in 11 of 18 patients. Chemical analysis of the shoe materials was performed. Finally, patients were tested with a thin-layer chromatogram of the shoe extracts and dilutions of the suspected rubber compound. All 18 patients showed positive reactions to thiuram mix. Ten of 11 patients reacted to a piece of shoe fabric. Chemical analysis showed the presence of dimethylthiocarbamylbenzothiazole sulfide (DMTBS). No thiurams were detected. Four patients tested with the chromatogram developed positive reactions to DMTBS. Positive reactions to low concentrations were observed in the 4 patients tested with a DMTBS dilution series; one patient reacted to 0.00001% in acetone. DMTBS, the culprit allergen, is a component formed during rubber vulcanization that probably cross-reacts with the thiuram mix. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Fourier-transform infrared spectroscopy as a novel approach to providing effect-based endpoints in duckweed toxicity testing.

PubMed

Hu, Li-Xin; Ying, Guang-Guo; Chen, Xiao-Wen; Huang, Guo-Yong; Liu, You-Sheng; Jiang, Yu-Xia; Pan, Chang-Gui; Tian, Fei; Martin, Francis L

2017-02-01

Traditional duckweed toxicity tests only measure plant growth inhibition as an endpoint, with limited effects-based data. The present study aimed to investigate whether Fourier-transform infrared (FTIR) spectroscopy could enhance the duckweed (Lemna minor L.) toxicity test. Four chemicals (Cu, Cd, atrazine, and acetochlor) and 4 metal-containing industrial wastewater samples were tested. After exposure of duckweed to the chemicals, standard toxicity endpoints (frond number and chlorophyll content) were determined; the fronds were also interrogated using FTIR spectroscopy under optimized test conditions. Biochemical alterations associated with each treatment were assessed and further analyzed by multivariate analysis. The results showed that comparable x% of effective concentration (ECx) values could be achieved based on FTIR spectroscopy in comparison with those based on traditional toxicity endpoints. Biochemical alterations associated with different doses of toxicant were mainly attributed to lipid, protein, nucleic acid, and carbohydrate structural changes, which helped to explain toxic mechanisms. With the help of multivariate analysis, separation of clusters related to different exposure doses could be achieved. The present study is the first to show successful application of FTIR spectroscopy in standard duckweed toxicity tests with biochemical alterations as new endpoints. Environ Toxicol Chem 2017;36:346-353. © 2016 SETAC. © 2016 SETAC.

Identifying Pleiotropic Genes in Genome-Wide Association Studies for Multivariate Phenotypes with Mixed Measurement Scales

PubMed Central

Williams, L. Keoki; Buu, Anne

2017-01-01

We propose a multivariate genome-wide association test for mixed continuous, binary, and ordinal phenotypes. A latent response model is used to estimate the correlation between phenotypes with different measurement scales so that the empirical distribution of the Fisher’s combination statistic under the null hypothesis is estimated efficiently. The simulation study shows that our proposed correlation estimation methods have high levels of accuracy. More importantly, our approach conservatively estimates the variance of the test statistic so that the type I error rate is controlled. The simulation also shows that the proposed test maintains the power at the level very close to that of the ideal analysis based on known latent phenotypes while controlling the type I error. In contrast, conventional approaches–dichotomizing all observed phenotypes or treating them as continuous variables–could either reduce the power or employ a linear regression model unfit for the data. Furthermore, the statistical analysis on the database of the Study of Addiction: Genetics and Environment (SAGE) demonstrates that conducting a multivariate test on multiple phenotypes can increase the power of identifying markers that may not be, otherwise, chosen using marginal tests. The proposed method also offers a new approach to analyzing the Fagerström Test for Nicotine Dependence as multivariate phenotypes in genome-wide association studies. PMID:28081206

The use of molecular and cytogenetic methods as a valuable tool in the detection of chromosomal abnormalities in horses: a case of sex chromosome chimerism in a Spanish purebred colt.

PubMed

Demyda-Peyrás, S; Membrillo, A; Bugno-Poniewierska, M; Pawlina, K; Anaya, G; Moreno-Millán, M

2013-01-01

Chromosomal abnormalities associated to sex chromosomes are reported as a problem more common than believed to be in horses. Most of them remain undiagnosed due to the complexity of the horse karyotype and the lack of interest of breeders and veterinarians in this type of diagnosis. Approximately 10 years ago, the Spanish Purebred Breeders Association implemented a DNA paternity test to evaluate the pedigree of every newborn foal. All candidates who showed abnormal or uncertain results are routinely submitted to cytogenetical analysis to evaluate the presence of chromosomal abnormalities. We studied the case of a foal showing 3 and even 4 different alleles in several loci in the short tandem repeat (STR) -based DNA parentage test. To confirm these results, a filiation test was repeated using follicular hair DNA showing normal results. A complete set of conventional and molecular cytogenetic analysis was performed to determine their chromosomal complements. C-banding and FISH had shown that the foal presents a sex chimerism 64,XX/64,XY with a cellular percentage of approximately 70/30, diagnosed in blood samples. The use of a diagnostic approach combining routine parentage QF-PCR-based STR screening tested with classical or molecular cytogenetic analysis could be a powerful tool that allows early detection of foals that will have a poor or even no reproductive performance due to chromosomal abnormalities, saving time, efforts and breeders' resources. Copyright © 2013 S. Karger AG, Basel.

The Drug Abuse Screening Test preserves its excellent psychometric properties in psychiatric patients evaluated in an emergency setting.

PubMed

Giguère, Charles-Édouard; Potvin, Stéphane

2017-01-01

Substance use disorders (SUDs) are significant risk factors for psychiatric relapses and hospitalizations in psychiatric populations. Unfortunately, no instrument has been validated for the screening of SUDs in psychiatric emergency settings. The Drug Abuse Screening Test (DAST) is widely used in the addiction field, but is has not been validated in that particular context. The objective of the current study is to examine the psychometric properties of the DAST administered to psychiatric populations evaluated in an emergency setting. The DAST was administered to 912 psychiatric patients in an emergency setting, of which 119 had a SUD (excluding those misusing alcohol only). The internal consistency, the construct validity, the test-retest reliability and the predictive validity (using SUD diagnoses) of the DAST were examined. The convergent validity was also examined, using a validated impulsivity scale. Regarding the internal consistency of the DAST, the Cronbach's alpha was 0.88. The confirmatory factor analysis showed that the DAST has one underlying factor. The test-retest reliability analysis produced a correlation coefficient of 0.86. ROC curve analyses produced an area under the curve of 0.799. Interestingly, a sex effect was observed. Finally, the convergent validity analysis showed that the DAST total score is specifically correlated with the sensation seeking dimension of impulsivity. The results of this validation study shows that the DAST preserves its excellent psychometric properties in psychiatric populations evaluated in an emergency setting. These results should encourage the use of the DAST in this unstable clinical situation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Assessment of mobility and bioavailability of contaminants in MSW incineration ash with aquatic and terrestrial bioassays.

PubMed

Ribé, V; Nehrenheim, E; Odlare, M

2014-10-01

Incineration of municipal solid waste (MSW) is a waste treatment method which can be sustainable in terms of waste volume reduction as well as a source of renewable energy. In the process fly and bottom ash is generated as a waste material. The ash residue may vary greatly in composition depending on the type of waste incinerated and it can contain elevated levels of harmful contaminants such as heavy metals. In this study, the ecotoxicity of a weathered, untreated incineration bottom ash was characterized as defined by the H14 criterion of the EU Waste Framework Directive by means of an elemental analysis, leaching tests followed by a chemical analysis and a combination of aquatic and solid-phase bioassays. The experiments were conducted to assess the mobility and bioavailability of ash contaminants. A combination of aquatic and terrestrial bioassays was used to determine potentially adverse acute effects of exposure to the solid ash and aqueous ash leachates. The results from the study showed that the bottom ash from a municipal waste incineration plant in mid-Sweden contained levels of metals such as Cu, Pb and Zn, which exceeded the Swedish EPA limit values for inert wastes. The chemical analysis of the ash leachates showed high concentrations of particularly Cr. The leachate concentration of Cr exceeded the limit value for L/S 10 leaching for inert wastes. Filtration of leachates prior to analysis may have underestimated the leachability of complex-forming metals such as Cu and Pb. The germination test of solid ash and ash leachates using T. repens showed a higher inhibition of seedling emergence of seeds exposed to the solid ash than the seeds exposed to ash leachates. This indicated a relatively low mobility of toxicants from the solid ash into the leachates, although some metals exceeded the L/S 10 leaching limit values for inert wastes. The Microtox® toxicity test showed only a very low toxic response to the ash leachate exposure, while the D. magna immobility test showed a moderately high toxic effect of the ash leachates. Overall, the results from this study showed an ecotoxic effect of the solid MSW bottom ash and the corresponding ash leachates. The material may therefore pose an environmental risk if used in construction applications. However, as the testing of the solid ash was rather limited and the ash leachate showed an unusually high leaching of Cr, further assessments are required in order to conclusively characterize the bottom ash studied herein as hazardous according to the H14 criterion. Copyright © 2014 Elsevier Ltd. All rights reserved.

[An evaluation of the effectiveness of laboratory diagnostic methods for brucellosis].

PubMed

Gandara, B; Zheludkov, M M; Chernysheva, M I

1994-01-01

The diagnostic value of bacteriological and serological methods for the laboratory diagnosis of brucellosis was studied. In the analysis of milk and cheese specimens Brucella cultures were isolated and differentiated as B.melitensis, biovar I, and B.abortus, biovar 4. In 25.6% of cases B.melitensis culture, biovar 1, was isolated from the blood of persons suspected for brucellosis. The isolation of B.melitensis culture from milk showed that this infective agent migrated from small animals to cattle, which was indicative of a high risk of human infection in the state of Zacatecas, Mexico. The comparative evaluation of serological diagnostic methods (the agglutination test in test tubes, Huddleson's slide test, the acidic rose bengal test and the 2-mercaptoethanol test) showed high sensitivity of rapid tests (Huddleson's test and the rose bengal test in 93.7% and 87.9% of cases respectively). The 2-mercaptoethanol test which gave positive results in 63.8% of cases provided additional information characterizing the course of infections process.

Critical processes and parameters in the development of accident tolerant fuels drop-in capsule irradiation tests

DOE PAGES

Barrett, K. E.; Ellis, K. D.; Glass, C. R.; ...

2015-12-01

The goal of the Accident Tolerant Fuel (ATF) program is to develop the next generation of Light Water Reactor (LWR) fuels with improved performance, reliability, and safety characteristics during normal operations and accident conditions and with reduced waste generation. An irradiation test series has been defined to assess the performance of proposed ATF concepts under normal LWR operating conditions. The Phase I ATF irradiation test series is planned to be performed as a series of drop-in capsule tests to be irradiated in the Advanced Test Reactor (ATR) operated by the Idaho National Laboratory (INL). Design, analysis, and fabrication processes formore » ATR drop-in capsule experiment preparation are presented in this paper to demonstrate the importance of special design considerations, parameter sensitivity analysis, and precise fabrication and inspection techniques for figure innovative materials used in ATF experiment assemblies. A Taylor Series Method sensitivity analysis approach was used to identify the most critical variables in cladding and rodlet stress, temperature, and pressure calculations for design analyses. The results showed that internal rodlet pressure calculations are most sensitive to the fission gas release rate uncertainty while temperature calculations are most sensitive to cladding I.D. and O.D. dimensional uncertainty. The analysis showed that stress calculations are most sensitive to rodlet internal pressure uncertainties, however the results also indicated that the inside radius, outside radius, and internal pressure were all magnified as they propagate through the stress equation. This study demonstrates the importance for ATF concept development teams to provide the fabricators as much information as possible about the material properties and behavior observed in prototype testing, mock-up fabrication and assembly, and chemical and mechanical testing of the materials that may have been performed in the concept development phase. Special handling, machining, welding, and inspection of materials, if known, should also be communicated to the experiment fabrication and inspection team.« less

Quantifying Antimicrobial Resistance at Veal Calf Farms

PubMed Central

Bosman, Angela B.; Wagenaar, Jaap; Stegeman, Arjan; Vernooij, Hans; Mevius, Dik

2012-01-01

This study was performed to determine a sampling strategy to quantify the prevalence of antimicrobial resistance on veal calf farms, based on the variation in antimicrobial resistance within and between calves on five farms. Faecal samples from 50 healthy calves (10 calves/farm) were collected. From each individual sample and one pooled faecal sample per farm, 90 selected Escherichia coli isolates were tested for their resistance against 25 mg/L amoxicillin, 25 mg/L tetracycline, 0.5 mg/L cefotaxime, 0.125 mg/L ciprofloxacin and 8/152 mg/L trimethoprim/sulfamethoxazole (tmp/s) by replica plating. From each faecal sample another 10 selected E. coli isolates were tested for their resistance by broth microdilution as a reference. Logistic regression analysis was performed to compare the odds of testing an isolate resistant between both test methods (replica plating vs. broth microdilution) and to evaluate the effect of pooling faecal samples. Bootstrap analysis was used to investigate the precision of the estimated prevalence of resistance to each antimicrobial obtained by several simulated sampling strategies. Replica plating showed similar odds of E. coli isolates tested resistant compared to broth microdilution, except for ciprofloxacin (OR 0.29, p≤0.05). Pooled samples showed in general lower odds of an isolate being resistant compared to individual samples, although these differences were not significant. Bootstrap analysis showed that within each antimicrobial the various compositions of a pooled sample provided consistent estimates for the mean proportion of resistant isolates. Sampling strategies should be based on the variation in resistance among isolates within faecal samples and between faecal samples, which may vary by antimicrobial. In our study, the optimal sampling strategy from the perspective of precision of the estimated levels of resistance and practicality consists of a pooled faecal sample from 20 individual animals, of which 90 isolates are tested for their susceptibility by replica plating. PMID:22970313

Analysis of Flame Deflector Spray Nozzles in Rocket Engine Test Stands

NASA Technical Reports Server (NTRS)

Sachdev, Jai S.; Ahuja, Vineet; Hosangadi, Ashvin; Allgood, Daniel C.

2010-01-01

The development of a unified tightly coupled multi-phase computational framework is described for the analysis and design of cooling spray nozzle configurations on the flame deflector in rocket engine test stands. An Eulerian formulation is used to model the disperse phase and is coupled to the gas-phase equations through momentum and heat transfer as well as phase change. The phase change formulation is modeled according to a modified form of the Hertz-Knudsen equation. Various simple test cases are presented to verify the validity of the numerical framework. The ability of the methodology to accurately predict the temperature load on the flame deflector is demonstrated though application to an actual sub-scale test facility. The CFD simulation was able to reproduce the result of the test-firing, showing that the spray nozzle configuration provided insufficient amount of cooling.

On-ground tests of the NISP infrared spectrometer instrument for Euclid

NASA Astrophysics Data System (ADS)

Jomni, Cyril; Ealet, Anne; Gillard, William; Prieto, Éric; Grupp, Frank U.

2017-09-01

Euclid is an ESA mission dedicated to understand the acceleration of the expansion of the Universe. The mission will measure hundred of millions of galaxies in spectrophotometry and photometry in the near infrared thanks to a spectro-photometer called NISP. This instrument will be assembled and tested in Marseille. To prepare the on-ground test plan and develop the test procedure, we have used simulated PSF images, based on a Zemax optical design of the instrument. We have developed the analysis tools that will be further used to build the procedure verification. We present here the method and analysis results to adjust the focus of the instrument. We will in particular show that because of the sampling of the PSF, a dithering strategy should be adapted and will constraint the development of the test plan.

[Performance of cognitive brief test in elderly patients with dementia in advanced stage living in an urban community of Lima, Peru].

PubMed

Custodio, Nilton; Alva-Diaz, Carlos; Becerra-Becerra, Yahaira; Montesinos, Rosa; Lira, David; Herrera-Pérez, Eder; Castro-Suárez, Sheila; Cuenca-Alfaro, José; Valeriano-Lorenzo, Elizabeth

2016-01-01

Evaluate the performance of clock drawing test- Manos versión (PDR-M) and Mini Mental State Examination -Peruvian version (MMSE) to detect dementia in a sample based on urban community of Lima, Peru. This study is a secondary analysis database, observational, analytical and cross-sectional, the gold standard was the clinical and the neuropsychological evaluations together. Performance testing individually and in combination were evaluated.. Data were obtained from prevalence study conducted in 2008 in Cercado de Lima. MMSE performance for evaluation of patients with dementia of any kind showed sensitivity of 64,1%, specificity of 84,1%, PPV of 24.4%, NPV of 96.7%, PLR of 4,03 and NLR of 0,43. PDR-M showed sensitivity of 89,3%, specificity of 98,1%, PPV of 79.3%, NPV of 99.1%, PLR of 47,79 and NLR of 0,11. When both tests were applied, and at least one of them was positive, they showed sensitivity 98.1%, specificity 84.1%, PPV of 33.1%, NPV of 99.8%, PLR of 6,17 and NLR of 0,02. When performing separate analysis of Alzheimer-type dementia and non- Alzheimer dementia, the values of the parameters do not differ substantially from those obtained for dementia of any kind. The combination of MMSE and PDR-M show good discriminative ability to detect moderate and severe dementia in population living in urban community in Lima.

Post irradiation analysis of RERTR-7A, 7B and RERTR-8 tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hofman, G.L.; Kim, Yeon Soo; Shevlyakov, G.V.

2008-07-15

Addition of 2 wt% or more of silicon in the Al matrix for U-Mo/Al dispersion fuel has proved to be effective in reducing interaction layer growth from the RERTR-7A test to a burnup of {approx}100 at% U-235 (LEU equivalent). The recent RERTR-8 test also showed the consistent results. In this paper, we present the post irradiation analysis results of these tests. A considerable number of monolithic fuel plates were irradiated in the RERTR-7A and RERTR-8 tests. The post irradiation results of these plates are also included. The RERTR-7B test was a lower burnup test with similar power to the RERTR-7A.more » In this test, dispersion fuel plates with U-7Mo-1Ti and U- 7Mo-2Zr in Al-5Si were irradiated. The post irradiation results of these plates are also covered. (author)« less

A powerful and robust test in genetic association studies.

PubMed

Cheng, Kuang-Fu; Lee, Jen-Yu

2014-01-01

There are several well-known single SNP tests presented in the literature for detecting gene-disease association signals. Having in place an efficient and robust testing process across all genetic models would allow a more comprehensive approach to analysis. Although some studies have shown that it is possible to construct such a test when the variants are common and the genetic model satisfies certain conditions, the model conditions are too restrictive and in general difficult to verify. In this paper, we propose a powerful and robust test without assuming any model restrictions. Our test is based on the selected 2 × 2 tables derived from the usual 2 × 3 table. By signals from these tables, we show through simulations across a wide range of allele frequencies and genetic models that this approach may produce a test which is almost uniformly most powerful in the analysis of low- and high-frequency variants. Two cancer studies are used to demonstrate applications of the proposed test. © 2014 S. Karger AG, Basel.

Flight and ground tests of a very low density elastomeric ablative material

NASA Technical Reports Server (NTRS)

Olsen, G. C.; Chapman, A. J., III

1972-01-01

A very low density ablative material, a silicone-phenolic composite, was flight tested on a recoverable spacecraft launched by a Pacemaker vehicle system; and, in addition, it was tested in an arc heated wind tunnel at three conditions which encompassed most of the reentry heating conditions of the flight tests. The material was composed, by weight, of 71 percent phenolic spheres, 22.8 percent silicone resin, 2.2 percent catalyst, and 4 percent silica fibers. The tests were conducted to evaluate the ablator performance in both arc tunnel and flight tests and to determine the predictability of the albator performance by using computed results from an existing one-dimensional numerical analysis. The flight tested ablator experienced only moderate surface recession and retained a smooth surface except for isolated areas where the char was completely removed, probably following reentry and prior to or during recovery. Analytical results show good agreement between arc tunnel and flight test results. The thermophysical properties used in the analysis are tabulated.

Analysis of structural dynamic data from Skylab. Volume 2: Skylab analytical and test model data

NASA Technical Reports Server (NTRS)

Demchak, L.; Harcrow, H.

1976-01-01

The orbital configuration test modal data, analytical test correlation modal data, and analytical flight configuration modal data are presented. Tables showing the generalized mass contributions (GMCs) for each of the thirty tests modes are given along with the two dimensional mode shape plots and tables of GMCs for the test correlated analytical modes. The two dimensional mode shape plots for the analytical modes and uncoupled and coupled modes of the orbital flight configuration at three development phases of the model are included.

Analysis of the Mechanical Behavior and Surface Rugosity of Different Dental Die Materials.

PubMed

Niekawa, Ciro T; Kreve, Simone; A'vila, Gisseli Bertozzi; Godoy, Gilmar Gil; Eduardo Vieira da Silva, J R; Dias, Sergio Candido

2017-01-01

This work evaluated the mechanical and surface behavior of different die materials. The studied materials are polyurethane resin Exakto-Form (Bredent), Gypsum type IV, Fuji Rock EP (Gc), and Durone (Dentsply). Two metallic matrices molded in polyvinyl siloxane provided 30 cylindrical test specimens for the diametral compression test and 30 hemispherical test specimens for the surface rugosity test. The cylindrical test specimens were submitted to tests of diametral compression strength using a DL2000 universal assay machine, with a load cell of 2000 Kgf and constant speed of 1 mm/min connected to the software. Kruskal-Wallis and Dunn's nonparametric tests were used to analyze the results. The hemispheres were submitted to the surface rugosity assay using a SJ201-P rugosimeter with a sensitivity of 300 μm, speed of 0.5 mm/s, and cut-off of 0.8 mm, and the readings were taken on the convex surface of the test specimens and metallic matrix. Results were analyzed using with Fisher's least significant differences test (LSD) and Dunnett's test. Kruskal-Wallis test showed significant difference between die materials for diametral compression strength ( P = 0.002). Dunn's test showed significantly higher values for modified polyurethane resin (Exakto-Form). The gypsum type IV, which did not significantly differ regarding diametral compression strength, showed 34.0% (Durone) and 42.7% (Fuji Rock) lower values in comparison to Exakto-Form. Within the parameters adopted in this study, it is possible to conclude that Exakto-Form polyurethane resin showed higher resistance to compression and was closer to the metallic matrix rugosity, and, along with the gypsum type IV Durone, showed better reproducibility of details relative to the Fuji Rock.

Lack of Thy1 (CD90) expression in neuroblastomas is correlated with impaired survival.

PubMed

Fiegel, Henning C; Kaifi, Jussuf T; Quaas, Alexander; Varol, Emine; Krickhahn, Annika; Metzger, Roman; Sauter, Guido; Till, Holger; Izbicki, Jakob R; Erttmann, Rudolf; Kluth, Dietrich

2008-01-01

Neuroblastoma (NBL) is the most common solid tumor in children. Tumors in advanced stage or with positive risk factors still have a poor prognosis. Thy1 (CD90) is a membrane glycoprotein expressed in thymus, retinal ganglionic cells, and several types of stem cells. The aim of this study was to assess Thy1 expression in NBL and analyze the correlation with clinical outcome. Sixty-three specimens of NBL were stained for Thy1 on a tissue microarray by immunohistochemistry. Fresh frozen tumor tissues were used for RNA isolation, and RT-PCR analysis for Thy1-mRNA expression was performed. Patients' survival data were correlated with Thy1 status using a log rank test and a Cox regression multivariate analysis. Thy1 was expressed on 51 (81%) of the tumors. Kaplan-Meier survival analysis showed a significantly impaired survival in patients with NBL missing Thy1 (P < 0.005 by log-rank test). A multivariate Cox regression showed an independent prognostic value of Thy1 status for overall survival (P < 0.05). In addition, the frequency of events and deaths was significantly higher in the group of patients with Thy1 negative tumors, as assessed by ANOVA analysis (P < 0.05 by F-test). The data showed that Thy1-negative NBL patients have a significantly impaired overall survival compared with Thy1-positive NBL patients. Thus, Thy1 seemed to be a marker with a specific prognostic value in NBL patients. Future studies are aiming at the biological role of this marker in the tumor cell differentiation.

metaCCA: summary statistics-based multivariate meta-analysis of genome-wide association studies using canonical correlation analysis.

PubMed

Cichonska, Anna; Rousu, Juho; Marttinen, Pekka; Kangas, Antti J; Soininen, Pasi; Lehtimäki, Terho; Raitakari, Olli T; Järvelin, Marjo-Riitta; Salomaa, Veikko; Ala-Korpela, Mika; Ripatti, Samuli; Pirinen, Matti

2016-07-01

A dominant approach to genetic association studies is to perform univariate tests between genotype-phenotype pairs. However, analyzing related traits together increases statistical power, and certain complex associations become detectable only when several variants are tested jointly. Currently, modest sample sizes of individual cohorts, and restricted availability of individual-level genotype-phenotype data across the cohorts limit conducting multivariate tests. We introduce metaCCA, a computational framework for summary statistics-based analysis of a single or multiple studies that allows multivariate representation of both genotype and phenotype. It extends the statistical technique of canonical correlation analysis to the setting where original individual-level records are not available, and employs a covariance shrinkage algorithm to achieve robustness.Multivariate meta-analysis of two Finnish studies of nuclear magnetic resonance metabolomics by metaCCA, using standard univariate output from the program SNPTEST, shows an excellent agreement with the pooled individual-level analysis of original data. Motivated by strong multivariate signals in the lipid genes tested, we envision that multivariate association testing using metaCCA has a great potential to provide novel insights from already published summary statistics from high-throughput phenotyping technologies. Code is available at https://github.com/aalto-ics-kepaco anna.cichonska@helsinki.fi or matti.pirinen@helsinki.fi Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press.

metaCCA: summary statistics-based multivariate meta-analysis of genome-wide association studies using canonical correlation analysis

PubMed Central

Cichonska, Anna; Rousu, Juho; Marttinen, Pekka; Kangas, Antti J.; Soininen, Pasi; Lehtimäki, Terho; Raitakari, Olli T.; Järvelin, Marjo-Riitta; Salomaa, Veikko; Ala-Korpela, Mika; Ripatti, Samuli; Pirinen, Matti

2016-01-01

Motivation: A dominant approach to genetic association studies is to perform univariate tests between genotype-phenotype pairs. However, analyzing related traits together increases statistical power, and certain complex associations become detectable only when several variants are tested jointly. Currently, modest sample sizes of individual cohorts, and restricted availability of individual-level genotype-phenotype data across the cohorts limit conducting multivariate tests. Results: We introduce metaCCA, a computational framework for summary statistics-based analysis of a single or multiple studies that allows multivariate representation of both genotype and phenotype. It extends the statistical technique of canonical correlation analysis to the setting where original individual-level records are not available, and employs a covariance shrinkage algorithm to achieve robustness. Multivariate meta-analysis of two Finnish studies of nuclear magnetic resonance metabolomics by metaCCA, using standard univariate output from the program SNPTEST, shows an excellent agreement with the pooled individual-level analysis of original data. Motivated by strong multivariate signals in the lipid genes tested, we envision that multivariate association testing using metaCCA has a great potential to provide novel insights from already published summary statistics from high-throughput phenotyping technologies. Availability and implementation: Code is available at https://github.com/aalto-ics-kepaco Contacts: anna.cichonska@helsinki.fi or matti.pirinen@helsinki.fi Supplementary information: Supplementary data are available at Bioinformatics online. PMID:27153689

Econo-ESA in semantic text similarity.

PubMed

Rahutomo, Faisal; Aritsugi, Masayoshi

2014-01-01

Explicit semantic analysis (ESA) utilizes an immense Wikipedia index matrix in its interpreter part. This part of the analysis multiplies a large matrix by a term vector to produce a high-dimensional concept vector. A similarity measurement between two texts is performed between two concept vectors with numerous dimensions. The cost is expensive in both interpretation and similarity measurement steps. This paper proposes an economic scheme of ESA, named econo-ESA. We investigate two aspects of this proposal: dimensional reduction and experiments with various data. We use eight recycling test collections in semantic text similarity. The experimental results show that both the dimensional reduction and test collection characteristics can influence the results. They also show that an appropriate concept reduction of econo-ESA can decrease the cost with minor differences in the results from the original ESA.

Real time automatic detection of bearing fault in induction machine using kurtogram analysis.

PubMed

Tafinine, Farid; Mokrani, Karim

2012-11-01

A proposed signal processing technique for incipient real time bearing fault detection based on kurtogram analysis is presented in this paper. The kurtogram is a fourth-order spectral analysis tool introduced for detecting and characterizing non-stationarities in a signal. This technique starts from investigating the resonance signatures over selected frequency bands to extract the representative features. The traditional spectral analysis is not appropriate for non-stationary vibration signal and for real time diagnosis. The performance of the proposed technique is examined by a series of experimental tests corresponding to different bearing conditions. Test results show that this signal processing technique is an effective bearing fault automatic detection method and gives a good basis for an integrated induction machine condition monitor.

Genotypic Analysis of Escherichia coli Strains from Poultry Carcasses and Their Susceptibilities to Antimicrobial Agents

PubMed Central

Geornaras, Ifigenia; Hastings, John W.; von Holy, Alexander

2001-01-01

Plasmid profiling and amplified fragment length polymorphism (AFLP) analysis were used to genotype 50 Escherichia coli strains from poultry carcasses. Thirty different plasmid profiles were evident, and clustering of the AFLP data showed that they were a distinctly heterogeneous group of strains. Susceptibility testing against five antimicrobial agents used in the South African poultry industry showed all strains to be susceptible to danofloxacin and colistin, while the majority (96%) were resistant to two tetracyclines. PMID:11282652

[Seed vigor evaluation based on adversity resistance index of wheat seed germination under stress conditions.

PubMed

Chen, Lei Tai; Sun, Ai Qing; Yang, Min; Chen, Lu Lu; Ma, Xue Li; Li, Mei Ling; Yin, Yan Ping

2016-09-01

A total of 16 wheat cultivars were selected to detect seed vigor of different genotypes using standard germination test, seed germination test under stress conditions and field emergence test. The adversity resistance indices of seed vigor indices and field emergence percentage under different germination conditions were used as the indices to evaluate adversity resistance. Principal component analysis and cluster analysis were used for the comprehensive evaluation of seed vigor. Results showed that drought stress, artificial aging and cold soaking treatments affected seed vigor to some extent. The adversity resistance indices of the artificial aging and cold soaking tests were significantly positively correlated with the field emergence percentage, while the adversity resistance index of drought stress test had no significant correlation with the field emergence percentage. 16 wheat cultivars were classified as three groups based on the principal component analysis and cluster analysis. Yunong 949, Yumai 49-198, Luyuan 502, Zhengyumai 9987, Shimai 21, Shannong 23, and Shixin 828 belonged to high vigor seeds. Xunong 5, Yunong 982, Tangmai 8, Jimai 20, Jimai 22, Jinan 17, and Shannong 20 belonged to medium vigor seeds. The other two cultivars, Chang 4738 and Lunxuan 061, belonged to low vigor seeds.

Round robin test for odour testing of migration waters.

PubMed

Rapp, Thomas; Günther, Herbert

2015-04-15

For a round robin test for EN 1420-1 (Odour assessment for organic materials in contact with drinking water) with 14 contributing laboratories from 10 European countries segments of a plastic pipe were sent to the laboratories which performed a migration test and an odour analysis of the migration waters (water that had contact with the organic material) according to the procedure described in the standard from 1999. In addition reference substances (Methyl tert-butyl ether, 1-butanol and hexanal) were investigated for their suitability to qualify the panels and the individual panellists. Methyl tert-butyl ether (MtBE) and 1-butanol proved to be suitable for this purpose, whereas hexanal showed a wide distribution of the individual odour threshold concentrations. Both possible testing options (unforced and forced choice) were performed and gave similar results. However, with respect to the qualification of the panellists and the data analysis the unforced choice procedure showed advantages. As human olfactory perception is used for the analysis, the reproducibility and the comparability between laboratories is of particular concern. For the pipe material the TON results of the different laboratories were in a range of ±1.5 dilutions based on a dilution factor of 2. This might be improved by taking the individual sensitivities of the panellists into account more strongly. Appropriate measures for the improvement of the test method appear to be the use of the proposed reference substances for the training of the panellists as well as the auditing and the selection of the panellists. The results of this round robin test are used in the revision process of the standard. Copyright © 2015 Elsevier Ltd. All rights reserved.

Gene set analysis using variance component tests.

PubMed

Huang, Yen-Tsung; Lin, Xihong

2013-06-28

Gene set analyses have become increasingly important in genomic research, as many complex diseases are contributed jointly by alterations of numerous genes. Genes often coordinate together as a functional repertoire, e.g., a biological pathway/network and are highly correlated. However, most of the existing gene set analysis methods do not fully account for the correlation among the genes. Here we propose to tackle this important feature of a gene set to improve statistical power in gene set analyses. We propose to model the effects of an independent variable, e.g., exposure/biological status (yes/no), on multiple gene expression values in a gene set using a multivariate linear regression model, where the correlation among the genes is explicitly modeled using a working covariance matrix. We develop TEGS (Test for the Effect of a Gene Set), a variance component test for the gene set effects by assuming a common distribution for regression coefficients in multivariate linear regression models, and calculate the p-values using permutation and a scaled chi-square approximation. We show using simulations that type I error is protected under different choices of working covariance matrices and power is improved as the working covariance approaches the true covariance. The global test is a special case of TEGS when correlation among genes in a gene set is ignored. Using both simulation data and a published diabetes dataset, we show that our test outperforms the commonly used approaches, the global test and gene set enrichment analysis (GSEA). We develop a gene set analyses method (TEGS) under the multivariate regression framework, which directly models the interdependence of the expression values in a gene set using a working covariance. TEGS outperforms two widely used methods, GSEA and global test in both simulation and a diabetes microarray data.

Histological analysis and identification of spermatogenesis-related genes in 2-, 6-, and 12-month-old sheep testes

NASA Astrophysics Data System (ADS)

Bai, Man; Sun, Limin; Zhao, Jia; Xiang, Lujie; Cheng, Xiaoyin; Li, Jiarong; Jia, Chao; Jiang, Huaizhi

2017-10-01

Testis development and spermatogenesis are vital factors that influence male animal fertility. In order to identify spermatogenesis-related genes and further provide a theory basis for finding biomarkers related to male sheep fertility, 2-, 6-, and 12-month-old Small Tail Han Sheep testes were selected to investigate the dynamic changes of sheep testis development. Hematoxylin-eosin routine staining and RNA-Seq technique were used to perform histological and transcriptome analysis for these testes. The results showed that 630, 102, and 322 differentially expressed genes (DEGs) were identified in 2- vs 6-month-old, 6- vs 12-month-old, and 2- vs 12-month-old testes, respectively. GO and KEGG analysis showed the following: DEGs in 2- vs 6-month-old testes were mainly related to the GO terms of sexual maturation and the pathways of multiple metabolism and biosynthesis; in 6- vs 12-month-old testes, most of the GO terms that DEGs involved in were related to metabolism and translation processes; the most significantly enriched pathway is the ribosome pathway. The union of DEGs in 2- vs 6-month-old, 6- vs 12-month-old, and 2- vs 12-month-old testes was categorized into eight profiles by series cluster. Subsequently, the eight profiles were classified into four model profiles and four co-expression networks were constructed based on the DEGs in these model profiles. Finally, 29 key regulatory genes related to spermatogenesis were identified in the four co-expression networks. The expression of 13 DEGs (CA3, APOH, MYOC, CATSPER4, SYT6, SERPINA10, DAZL, ADIPOR2, RAB13, CEP41, SPAG4, ODF1, and FRG1) was validated by RT-PCR.

Unified Sequence-Based Association Tests Allowing for Multiple Functional Annotations and Meta-analysis of Noncoding Variation in Metabochip Data.

PubMed

He, Zihuai; Xu, Bin; Lee, Seunggeun; Ionita-Laza, Iuliana

2017-09-07

Substantial progress has been made in the functional annotation of genetic variation in the human genome. Integrative analysis that incorporates such functional annotations into sequencing studies can aid the discovery of disease-associated genetic variants, especially those with unknown function and located outside protein-coding regions. Direct incorporation of one functional annotation as weight in existing dispersion and burden tests can suffer substantial loss of power when the functional annotation is not predictive of the risk status of a variant. Here, we have developed unified tests that can utilize multiple functional annotations simultaneously for integrative association analysis with efficient computational techniques. We show that the proposed tests significantly improve power when variant risk status can be predicted by functional annotations. Importantly, when functional annotations are not predictive of risk status, the proposed tests incur only minimal loss of power in relation to existing dispersion and burden tests, and under certain circumstances they can even have improved power by learning a weight that better approximates the underlying disease model in a data-adaptive manner. The tests can be constructed with summary statistics of existing dispersion and burden tests for sequencing data, therefore allowing meta-analysis of multiple studies without sharing individual-level data. We applied the proposed tests to a meta-analysis of noncoding rare variants in Metabochip data on 12,281 individuals from eight studies for lipid traits. By incorporating the Eigen functional score, we detected significant associations between noncoding rare variants in SLC22A3 and low-density lipoprotein and total cholesterol, associations that are missed by standard dispersion and burden tests. Copyright © 2017 American Society of Human Genetics. Published by Elsevier Inc. All rights reserved.

Gene expression analysis in zebrafish embryos: a potential approach to predict effect concentrations in the fish early life stage test.

PubMed

Weil, Mirco; Scholz, Stefan; Zimmer, Michaela; Sacher, Frank; Duis, Karen

2009-09-01

Based on the hypothesis that analysis of gene expression could be used to predict chronic fish toxicity, the zebrafish (Danio rerio) embryo test (DarT), developed as a replacement method for the acute fish test, was expanded to a gene expression D. rerio embryo test (Gene-DarT). The effects of 14 substances on lethal and sublethal endpoints of the DarT and on expression of potential marker genes were investigated: the aryl hydrocarbon receptor 2, cytochrome P450 1A (cypla), heat shock protein 70, fizzy-related protein 1, the transcription factors v-maf musculoaponeurotic fibrosarcoma oncogene family protein g (avian) 1 and NF-E2-p45-related factor, and heme oxygenase 1 (hmox1). After exposure of zebrafish embryos for 48 h, differential gene expression was evaluated using reverse transcriptase-polymerase chain reaction, gel electrophoresis, and densitometric analysis of the gels. All tested compounds significantly affected the expression of at least one potential marker gene, with cyp1a and hmox1 being most sensitive. Lowest-observed-effect concentrations (LOECs) for gene expression were below concentrations resulting in 10% lethal effects in the DarT. For 10 (3,4- and 3,5-dichloroaniline, 1,4-dichlorobenzene, 2,4-dinitrophenol, atrazine, parathion-ethyl, chlorotoluron, genistein, 4-nitroquinoline-1-oxide, and cadmium) out of the 14 tested substances, LOEC values derived with the Gene-DarT differ by a factor of less than 10 from LOEC values of fish early life stage tests with zebrafish. For pentachloroaniline and pentachlorobenzene, the Gene-DarT showed a 23- and 153-fold higher sensitivity, respectively, while for lindane, it showed a 13-fold lower sensitivity. For ivermectin, the Gene-DarT was by a factor of more than 1,000 less sensitive than the acute fish test. The results of the present study indicate that gene expression analysis in zebrafish embryos could principally be used to predict effect concentrations in the fish early life stage test.

Differences in genotoxic activity of alpha-Ni3S2 on human lymphocytes from nickel-hypersensitized and nickel-unsensitized donors.

PubMed

Arrouijal, F Z; Marzin, D; Hildebrand, H F; Pestel, J; Haguenoer, J M

1992-05-01

The genotoxic activity of alpha-Ni3S2 was assessed on human lymphocytes from nickel-hypersensitized (SSL) and nickel-unsensitized (USL) subjects. Three genotoxicity tests were performed: the sister chromatid exchange (SCE) test, the metaphase analysis test and the micronucleus test. (i) The SCE test (3-100 micrograms/ml) showed a weak but statistically significant increase in the number of SCE in both lymphocyte types with respect to controls, USL presenting a slightly higher SCE incidence but only at one concentration. (ii) The metaphase analysis test demonstrated a high dose-dependent clastogenic activity of alpha-Ni3S2 in both lymphocyte types. The frequency of chromosomal anomalies was significantly higher in USL than in SSL for all concentrations applied. (iii) The micronucleus test confirmed the dose-dependent clastogenic activity of alpha-Ni3S2 and the differences already observed between USL and SSL, i.e. the number of cells with micronuclei was statistically higher in USL. Finally, the incorporation study with alpha-63Ni3S2 showed a higher uptake of its solubilized fraction by USL. This allows an explanation of the different genotoxic action of nickel on the two cell types. In this study we demonstrated that hypersensitivity has an influence on the incorporation of alpha-Ni3S2 and subsequently on the different induction of chromosomal aberrations in human lymphocytes.

Assessment of the announced North Korean nuclear test using long-range atmospheric transport and dispersion modelling.

PubMed

De Meutter, Pieter; Camps, Johan; Delcloo, Andy; Termonia, Piet

2017-08-18

On 6 January 2016, the Democratic People's Republic of Korea announced to have conducted its fourth nuclear test. Analysis of the corresponding seismic waves from the Punggye-ri nuclear test site showed indeed that an underground man-made explosion took place, although the nuclear origin of the explosion needs confirmation. Seven weeks after the announced nuclear test, radioactive xenon was observed in Japan by a noble gas measurement station of the International Monitoring System. In this paper, atmospheric transport modelling is used to show that the measured radioactive xenon is compatible with a delayed release from the Punggye-ri nuclear test site. An uncertainty quantification on the modelling results is given by using the ensemble method. The latter is important for policy makers and helps advance data fusion, where different nuclear Test-Ban-Treaty monitoring techniques are combined.

The Statistical Analysis Techniques to Support the NGNP Fuel Performance Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bihn T. Pham; Jeffrey J. Einerson

2010-06-01

This paper describes the development and application of statistical analysis techniques to support the AGR experimental program on NGNP fuel performance. The experiments conducted in the Idaho National Laboratory’s Advanced Test Reactor employ fuel compacts placed in a graphite cylinder shrouded by a steel capsule. The tests are instrumented with thermocouples embedded in graphite blocks and the target quantity (fuel/graphite temperature) is regulated by the He-Ne gas mixture that fills the gap volume. Three techniques for statistical analysis, namely control charting, correlation analysis, and regression analysis, are implemented in the SAS-based NGNP Data Management and Analysis System (NDMAS) for automatedmore » processing and qualification of the AGR measured data. The NDMAS also stores daily neutronic (power) and thermal (heat transfer) code simulation results along with the measurement data, allowing for their combined use and comparative scrutiny. The ultimate objective of this work includes (a) a multi-faceted system for data monitoring and data accuracy testing, (b) identification of possible modes of diagnostics deterioration and changes in experimental conditions, (c) qualification of data for use in code validation, and (d) identification and use of data trends to support effective control of test conditions with respect to the test target. Analysis results and examples given in the paper show the three statistical analysis techniques providing a complementary capability to warn of thermocouple failures. It also suggests that the regression analysis models relating calculated fuel temperatures and thermocouple readings can enable online regulation of experimental parameters (i.e. gas mixture content), to effectively maintain the target quantity (fuel temperature) within a given range.« less

Healing of skin wounds with a chitosan-gelatin sponge loaded with tannins and platelet-rich plasma.

PubMed

Lu, Bitao; Wang, Tianyou; Li, Zhiquan; Dai, Fangying; Lv, Lingmei; Tang, Fengling; Yu, Kun; Liu, Jiawei; Lan, Guangqian

2016-01-01

A chitosan-gelatin sponge (CSGT) was prepared using a chitosan/ascorbic acid solution blend containing gelatin, followed by crosslinking with tannin acid and freeze-drying, thereby combining the chitosan sponge and gelatin sponge. The structure of the CSGT was observed by scanning electron microscopy and was shown to have uniform and abundant pores measuring about 145-240μm in size. We also characterized the sponges by infrared spectroscopy, thermogravimetric analysis, mechanical property tests, swelling behavior analysis, water retention capacity tests, antibacterial property analysis, and cytotoxicity tests. Our data showed that the CSGT had good thermostability and mechanical properties as well as efficient water absorption and retention capacities. Moreover, the CSGT could effectively inhibit the growth of Escherichia coli and Staphylococcus aureus with low toxicity. In animal experiments, macroscopic observations and histological examinations showed that the wound covered by the CSGT healed quickly. Additionally, loading of the CSGT with platelet-rich plasma resulted in further acceleration of wound healing. Therefore, the CSGT and the CSGT with platelet-rich plasma were suitable for application as a wound dressing and may have potential for use in various biomedical applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Sequential Blood Filtration for Extracorporeal Circulation: Initial Results from a Proof-of-Concept Prototype.

PubMed

Herbst, Daniel P

2014-09-01

Micropore filters are used during extracorporeal circulation to prevent gaseous and solid particles from entering the patient's systemic circulation. Although these devices improve patient safety, limitations in current designs have prompted the development of a new concept in micropore filtration. A prototype of the new design was made using 40-μm filter screens and compared against four commercially available filters for performance in pressure loss and gross air handling. Pre- and postfilter bubble counts for 5- and 10-mL bolus injections in an ex vivo test circuit were recorded using a Doppler ultrasound bubble counter. Statistical analysis of results for bubble volume reduction between test filters was performed with one-way repeated-measures analysis of variance using Bonferroni post hoc tests. Changes in filter performance with changes in microbubble load were also assessed with dependent t tests using the 5- and 10-mL bolus injections as the paired sample for each filter. Significance was set at p < .05. All filters in the test group were comparable in pressure loss performance, showing a range of 26-33 mmHg at a flow rate of 6 L/min. In gross air-handling studies, the prototype showed improved bubble volume reduction, reaching statistical significance with three of the four commercial filters. All test filters showed decreased performance in bubble volume reduction when the microbubble load was increased. Findings from this research support the underpinning theories of a sequential arterial-line filter design and suggest that improvements in microbubble filtration may be possible using this technique.

Reliability and validity of the Children's Fear Survey Schedule-Dental Subscale for Arabic-speaking children: a cross-sectional study.

PubMed

El-Housseiny, Azza A; Alsadat, Farah A; Alamoudi, Najlaa M; El Derwi, Douaa A; Farsi, Najat M; Attar, Moaz H; Andijani, Basil M

2016-04-14

Early recognition of dental fear is essential for the effective delivery of dental care. This study aimed to test the reliability and validity of the Arabic version of the Children's Fear Survey Schedule-Dental Subscale (CFSS-DS). A school-based sample of 1546 children was randomly recruited. The Arabic version of the CFSS-DS was completed by children during class time. The scale was tested for internal consistency and test-retest reliability. To test criterion validity, children's behavior was assessed using the Frankl scale during dental examination, and results were compared with children's CFSS-DS scores. To test the scale's construct validity, scores on "fear of going to the dentist soon" were correlated with CFSS-DS scores. Factor analysis was also used. The Arabic version of the CFSS-DS showed high reliability regarding both test-retest reliability (intraclass correlation = 0.83, p < 0.001) and internal consistency (Cronbach's α = 0.88). It showed good criterion validity: children with negative behavior had significantly higher fear scores (t = 13.67, p < 0.001). It also showed moderate construct validity (Spearman's rho correlation, r = 0.53, p < 0.001). Factor analysis identified the following factors: "fear of invasive dental procedures," "fear of less invasive dental procedures" and "fear of strangers." The Arabic version of the CFSS-DS is a reliable and valid measure of dental fear in Arabic-speaking children. Pediatric dentists and researchers may use this validated version of the CFSS-DS to measure dental fear in Arabic-speaking children.

Sequential Blood Filtration for Extracorporeal Circulation: Initial Results from a Proof-of-Concept Prototype

PubMed Central

Herbst, Daniel P.

2014-01-01

Abstract: Micropore filters are used during extracorporeal circulation to prevent gaseous and solid particles from entering the patient’s systemic circulation. Although these devices improve patient safety, limitations in current designs have prompted the development of a new concept in micropore filtration. A prototype of the new design was made using 40-μm filter screens and compared against four commercially available filters for performance in pressure loss and gross air handling. Pre- and postfilter bubble counts for 5- and 10-mL bolus injections in an ex vivo test circuit were recorded using a Doppler ultrasound bubble counter. Statistical analysis of results for bubble volume reduction between test filters was performed with one-way repeated-measures analysis of variance using Bonferroni post hoc tests. Changes in filter performance with changes in microbubble load were also assessed with dependent t tests using the 5- and 10-mL bolus injections as the paired sample for each filter. Significance was set at p < .05. All filters in the test group were comparable in pressure loss performance, showing a range of 26–33 mmHg at a flow rate of 6 L/min. In gross air-handling studies, the prototype showed improved bubble volume reduction, reaching statistical significance with three of the four commercial filters. All test filters showed decreased performance in bubble volume reduction when the microbubble load was increased. Findings from this research support the underpinning theories of a sequential arterial-line filter design and suggest that improvements in microbubble filtration may be possible using this technique. PMID:26357790

Turkish Scorzonera Species Extracts Attenuate Cytokine Secretion via Inhibition of NF-κB Activation, Showing Anti-Inflammatory Effect in Vitro.

PubMed

Bahadır Acikara, Özlem; Hošek, Jan; Babula, Petr; Cvačka, Josef; Budešínský, Miloš; Dračinský, Martin; Saltan İşcan, Gülçin; Kadlecová, Daniela; Ballová, Ludmila; Šmejkal, Karel

2015-12-30

Scorzonera species are used in different folk medicines to combat many diseases, including the illnesses connected with inflammation. Previous experiments showed anti-inflammatory activity of Scorzonera extracts in vivo. S. latifolia, S. cana var. jacquiniana, S. tomentosa, S. mollis ssp. szowitsii, S. eriophora, S. incisa, S. cinerea, and S. parviflora extracts were, therefore, evaluated for their inhibitory activities of TNF-α and IL-1β production, and NF-κB nuclear translocation in THP-1 macrophages. The HPLC analysis was carried out to elucidate and to compare the composition of these extracts. Major compounds of the tested extracts have been isolated using different chromatographic techniques and further tested for their inhibitory activities on TNF-α and IL-1β production. Several extracts showed promising anti-inflammatory activity in these in vitro tests. Results of HPLC analysis revealed chlorogenic acid as a compound present in all tested extracts. Hyperoside, quercetin-3-O-β-d-glucoside and rutin were also present in varying amount in some Scorzonera species analyzed. Furthermore, eight phenolics which were identified as quercetin-3-O-β-d-glucoside (1), hyperoside (2), hydrangenol-8-O-glucoside (3), swertisin (4), 7-methylisoorientin (5), 4,5-O-dicaffeoyl-quinic acid (6), 3,5-di-O-caffeoyl-quinic acid (7), and chlorogenic acid (8) have been isolated as major phenolic compounds of the tested extracts and, together with eight terpenoids (9-16) previously obtained from different Scorzonera species, have been tested for the inhibition of TNF-α production, unfortunately with no activity comparable with standard.

The chemical constitution and biocompatibility of accelerated Portland cement for endodontic use.

PubMed

Camilleri, J; Montesin, F E; Di Silvio, L; Pitt Ford, T R

2005-11-01

To evaluate the biocompatibility of mineral trioxide aggregate and accelerated Portland cement and their eluants by assessing cell metabolic function and proliferation. The chemical constitution of grey and white Portland cement, grey and white mineral trioxide aggregate (MTA) and accelerated Portland cement produced by excluding gypsum from the manufacturing process (Aalborg White) was determined using both energy dispersive analysis with X-ray and X-ray diffraction analysis. Biocompatibility of the materials was assessed using a direct test method where cell proliferation was measured quantitatively using Alamar Blue dye and an indirect test method where cells were grown on material elutions and cell proliferation was assessed using methyltetrazolium assay as recommended by the International standard guidelines, ISO 10993-Part 5 for in vitro testing. The chemical constitution of all the materials tested was similar. Indirect studies of the eluants showed an increase in cell activity after 24 h compared with the control in culture medium (P<0.05). Direct cell contact with the cements resulted in a fall in cell viability for all time points studied (P<0.001). Biocompatibility testing of the cement eluants showed the presence of no toxic leachables from the grey or white MTA, and that the addition of bismuth oxide to the accelerated Portland cement did not interfere with biocompatibility. The new accelerated Portland cement showed similar results. Cell growth was poor when seeded in direct contact with the test cements. However, the elution made up of calcium hydroxide produced during the hydration reaction was shown to induce cell proliferation.

Microbial biofilm studies of the Environmental Control and Life Support System water recovery test for Space Station Freedom

NASA Technical Reports Server (NTRS)

Obenhuber, D. C.; Huff, T. L.; Rodgers, E. B.

1991-01-01

Analysis of biofilm accumulation, studies of iodine disinfection of biofilm, and the potential for microbially influenced corrosion in the water recovery test (WRT) are presented. The analysis of WRT components showed the presence of biofilms and organic deposits in selected tubing. Water samples from the WRT contained sulfate-reducing and acid-producing organisms implicated in corrosion processes. Corrosion of an aluminum alloy was accelerated in the presence of these water samples, but stainless steel corrosion rates were not accelerated.

Testing and Analysis of Sensor Ports

NASA Technical Reports Server (NTRS)

Zhang, M.; Frendi, A.; Thompson, W.; Casiano, M. J.

2016-01-01

This Technical Publication summarizes the work focused on the testing and analysis of sensor ports. The tasks under this contract were divided into three areas: (1) Development of an Analytical Model, (2) Conducting a Set of Experiments, and (3) Obtaining Computational Solutions. Results from the experiment using both short and long sensor ports were obtained using harmonic, random, and frequency sweep plane acoustic waves. An amplification factor of the pressure signal between the port inlet and the back of the port is obtained and compared to models. Comparisons of model and experimental results showed very good agreement.

Analytical investigation of solid rocket nozzle failure

NASA Technical Reports Server (NTRS)

Mccoy, K. E.; Hester, J.

1985-01-01

On April 5, 1983, an Inertial Upper Stage (IUS) spacecraft experienced loss of control during the burn of the second of two solid rocket motors. The anomaly investigation showed the cause to be a malfunction of the solid rocket motor. This paper presents a description of the IUS system, a failure analysis summary, an account of the thermal testing and computer modeling done at Marshall Space Flight Center, a comparison of analysis results with thermal data obtained from motor static tests, and describes some of the design enhancement incorporated to prevent recurrence of the anomaly.

Effects of listening to pleasant music on chronic unilateral neglect: a single-subject study.

PubMed

Tsai, Pei-Luen; Chen, Mei-Ching; Huang, Yu-Ting; Lin, Keh-Chung

2013-01-01

Recent studies suggest that the positive emotion induced by pleasant music may improve cognitive functions. We used the single-subject design to study whether listening to preferred music may reduce unilateral neglect in two participants with post-stroke neglect. These participants were instructed to listen to their preferred music every day for 5 weeks, followed by 2 weeks of follow-up assessment. Outcome measures involved the Star Cancellation Test, the Line Bisection Test, and the visual exploration task. A combination of visual analysis and the two-standard-deviation band method was used for data analysis. Both participants showed significant intervention-related improvements on all outcome measures except the Line Bisection Test, on which one participant showed no improvement. The therapeutic effects were maintained during the follow-up phase. The findings suggest that positive emotion, evoked by preferred music, may be used to ameliorate unilateral neglect. Further research using controlled trials is warranted to validate the findings.

Colorimeter and scanning electron microscopy analysis of teeth submitted to internal bleaching.

PubMed

Martin-Biedma, Benjamin; Gonzalez-Gonzalez, Teresa; Lopes, Manuela; Lopes, Luis; Vilar, Rui; Bahillo, José; Varela-Patiño, Purificación

2010-02-01

This in vitro study compared the tooth color and the ultrastructure of internal dental tissues before and after internal bleaching. Sodium perborate was placed in the pulp chamber of endodontically treated molars and sealed with intermediate restorative material. The test samples were stored in a physiologic solution, and the bleaching agent was replaced every 7 days. A control group was used. After 1 month, the colors of the test and control samples were measured with a colorimeter, and the internal surfaces were observed under field emission scanning electron microscopy (FESEM). Statistically significant differences were found between the test and control sample colors. The FESEM ultrastructure analysis of the internal enamel and dentin surfaces did not show any changes after the internal bleaching. The results of the present study show that sodium perborate is effective in bleaching nonvital teeth and does not produce ultrastructural changes in the dental tissues. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

A European multicientre study on the comparison of HIV-1 viral loads between VERIS HIV-1 Assay and Roche COBAS® TAQMAN® HIV-1 test, Abbott RealTime HIV-1 Assay, and Siemens VERSANT HIV-1 Assay.

PubMed

Braun, Patrick; Delgado, Rafael; Drago, Monica; Fanti, Diana; Fleury, Hervé; Hofmann, Jörg; Izopet, Jacques; Kühn, Sebastian; Lombardi, Alessandra; Mancon, Alessandro; Marcos, Mª Angeles; Mileto, Davide; Sauné, Karine; O'Shea, Siobhan; Pérez-Rivilla, Alfredo; Ramble, John; Trimoulet, Pascale; Vila, Jordi; Whittaker, Duncan; Artus, Alain; Rhodes, Daniel

2017-07-01

Viral load monitoring is essential for patients under treatment for HIV. Beckman Coulter has developed the VERIS HIV-1 Assay for use on the novel, automated DxN VERIS Molecular Diagnostics System. ¥ OBJECTIVES: Evaluation of the clinical performance of the new quantitative VERIS HIV-1 Assay at multiple EU laboratories. Method comparison with the VERIS HIV-1 Assay was performed with 415 specimens at 5 sites tested with COBAS ® AmpliPrep/COBAS ® TaqMan ® HIV-1 Test, v2.0, 169 specimens at 3 sites tested with RealTime HIV-1 Assay, and 202 specimens from 2 sites tested with VERSANT HIV-1 Assay. Patient monitoring sample results from 4 sites were also compared. Bland-Altman analysis showed the average bias between VERIS HIV-1 Assay and COBAS HIV-1 Test, RealTime HIV-1 Assay, and VERSANT HIV-1 Assay to be 0.28, 0.39, and 0.61 log 10 cp/mL, respectively. Bias at low end levels below 1000cp/mL showed predicted bias to be <0.3 log 10 cp/mL for VERIS HIV-1 Assay versus COBAS HIV-1 Test and RealTime HIV-1 Assay, and <0.5 log 10 cp/mL versus VERSANT HIV-1 Assay. Analysis on 174 specimens tested with the 0.175mL volume VERIS HIV-1 Assay and COBAS HIV-1 Test showed average bias of 0.39 log 10 cp/mL. Patient monitoring results using VERIS HIV-1 Assay demonstrated similar viral load trends over time to all comparators. The VERIS HIV-1 Assay for use on the DxN VERIS System demonstrated comparable clinical performance to COBAS ® HIV-1 Test, RealTime HIV-1 Assay, and VERSANT HIV-1 Assay. Copyright © 2017 Elsevier B.V. All rights reserved.

Four-way-leaning test shows larger limits of stability than a circular-leaning test.

PubMed

Thomsen, Mikkel Højgaard; Støttrup, Nicolai; Larsen, Frederik Greve; Pedersen, Ann-Marie Sydow Krogh; Poulsen, Anne Grove; Hirata, Rogerio Pessoto

2017-01-01

Limits of stability (LOS) have extensive clinical and rehabilitational value yet no standard consensus on measuring LOS exists. LOS measured using a leaning or a circling protocol is commonly used in research and clinical settings, however differences in protocols and reliability problems exist. This study measured LOS using a four-way-leaning test and a circular-leaning test to test which showed larger LOS measurements. Furthermore, number of adaptation trials needed for consistent results was assessed. Limits of stability were measured using a force plate (Metitur Good Balance System ® ) sampling at 50Hz. Thirty healthy subjects completed 30 trials assessing LOS alternating between four-way-leaning test and circular-leaning test. A main effect of methods (ANOVA:F(1,28)=45.86, P<0.01) with the four-way-leaning test showing larger values than the circular-leaning test (NK, P<0.01). An interaction between method×directions was found (ANOVA:F(3, 84)=24.87, P<0.01). The four-way-leaning test showed larger LOS in anterior (NK, P<0.05), right (NK, P<0.01) and left direction (NK, P<0.01). Analysis of LOS for the four-way-leaning test showed a difference between trials (ANOVA:F(14,392)=7.81, P<0.01). Differences were found between trial 1 and 7 (NK, P<0.03), trial 6 and 8 (NK, P<0.02) and trial 7 and 15 (NK, P<0.02). Four-way-leaning test showed high correlation (ICC>0.87) between first and second trial for all directions. Four-way-leaning test yields larger LOS in anterior, right and left direction making it more reliable when measuring LOS. A learning effect was found up to the 8th trial, which suggests using 8 adaptation trials before reliable LOS is measured. Copyright © 2016 Elsevier B.V. All rights reserved.

Registered nurses' medication management of the elderly in aged care facilities.

PubMed

Lim, L M; Chiu, L H; Dohrmann, J; Tan, K-L

2010-03-01

Data on adverse drug reactions (ADRs) showed a rising trend in the elderly over 65 years using multiple medications. To identify registered nurses' (RNs) knowledge of medication management and ADRs in the elderly in aged care facilities; evaluate an education programme to increase pharmacology knowledge and prevent ADRs in the elderly; and develop a learning programme with a view to extending provision, if successful. This exploratory study used a non-randomized pre- and post-test one group quasi-experimental design without comparators. It comprised a 23-item knowledge-based test questionnaire, one-hour teaching session and a self-directed learning package. The volunteer sample was RNs from residential aged care facilities, involved in medication management. Participants sat a pre-test immediately before the education, and post-test 4 weeks later (same questionnaire). Participants' perceptions obtained. Pre-test sample n = 58, post-test n = 40, attrition rate of 31%. Using Microsoft Excel 2000, descriptive statistical data analysis of overall pre- and post-test incorrect responses showed: pre-test proportion of incorrect responses = 0.40; post-test proportion of incorrect responses = 0.27; Z-test comparing pre- and post-tests scores of incorrect responses = 6.55 and one-sided P-value = 2.8E-11 (P < 0.001). Pre-test showed knowledge deficits in medication management and ADRs in the elderly; post-test showed statistically significant improvement in RNs' knowledge. It highlighted a need for continuing professional education. Further studies are required on a larger sample of RNs in other aged care facilities, and on the clinical impact of education by investigating nursing practice and elderly residents' outcomes.

Parameter studies of sediments in the Storegga Slide region

NASA Astrophysics Data System (ADS)

Yang, S. L.; Kvalstad, T.; Solheim, A.; Forsberg, C. F.

2006-09-01

Based on classification tests, oedometer tests, fall-cone tests and triaxial tests, physical and mechanical properties of sediments in the Storegga Slide region were analysed to assess parameter interrelationships. The data show good relationships between a number of physical and mechanical parameters. Goodness of fit between compression index and various physical parameters can be improved by multiple regression analysis. The interclay void ratio and liquidity index correlate well with the undrained shear strength of clay. Sediments with higher water content, liquid limit, activity, interclay void ratio, plasticity index and liquidity index showed higher compression index and/or lower undrained shear strength. Some relationships between parameters were tested by using data from two other sites south of the Storegga Slide. A better understanding of properties of sediments in regions such as that of the Storegga Slide can be obtained through this approach.

The effects of simulated bone loss on the implant-abutment assembly and likelihood of fracture: an in vitro study.

PubMed

Manzoor, Behzad; Suleiman, Mahmood; Palmer, Richard M

2013-01-01

The crestal bone level around a dental implant may influence its strength characteristics by offering protection against mechanical failures. Therefore, the present study investigated the effect of simulated bone loss on modes, loads, and cycles to failure in an in vitro model. Different amounts of bone loss were simulated: 0, 1.5, 3.0, and 4.5 mm from the implant head. Forty narrow-diameter (3.0-mm) implant-abutment assemblies were tested using compressive bending and cyclic fatigue testing. Weibull and accelerated life testing analysis were used to assess reliability and functional life. Statistical analyses were performed using the Fisher-Exact test and the Spearman ranked correlation. Compressive bending tests showed that the level of bone loss influenced the load-bearing capacity of implant-abutment assemblies. Fatigue testing showed that the modes, loads, and cycles to failure had a statistically significant relationship with the level of bone loss. All 16 samples with bone loss of 3.0 mm or more experienced horizontal implant body fractures. In contrast, 14 of 16 samples with 0 and 1.5 mm of bone loss showed abutment and screw fractures. Weibull and accelerated life testing analysis indicated a two-group distribution: the 0- and 1.5-mm bone loss samples had better functional life and reliability than the 3.0- and 4.5-mm samples. Progressive bone loss had a significant effect on modes, loads, and cycles to failure. In addition, bone loss influenced the functional life and reliability of the implant-abutment assemblies. Maintaining crestal bone levels is important in ensuring biomechanical sustainability and predictable long-term function of dental implant assemblies.

Improving Students' Self-Efficacy in Strategic Management: The Relative Impact of Cases and Simulations.

ERIC Educational Resources Information Center

Tompson, George H.; Dass, Parshotam

2000-01-01

Investigates the relative contribution of computer simulations and case studies for improving undergraduate students' self-efficacy in strategic management courses. Results of pre-and post-test data, regression analysis, and analysis of variance show that simulations result in significantly higher improvement in self-efficacy than case studies.…

Shuttle Return-to-Flight IH-108 Aerothermal Test at CUBRC - Flow Field Calibration and CFD

NASA Technical Reports Server (NTRS)

Lau, Kei Y.; Holden, M. S.

2011-01-01

This paper discusses one specific aspect of the Shuttle Retrun-To-Flight IH-108 Aerothermal Test at Calspan-University of Buffalo Research Center (CUBRC), the test flow field calibration. It showed the versatility of the CUBRC Large Energy National Shock Tunnel (LENS) II wind tunnel for an aerothermal test with unique and demanding requirements. CFD analyses were used effectively to extend the test range at the low end of the Mach range. It demonstrated how ground test facility and CFD synergy can be utilitzed iteratively to enhance the confidence in the fedility of both tools. It addressed the lingering concerns of the aerothermal community on use of inpulse facility and CFD analysis. At the conclusion of the test program, members from the NASA Marshall (MSFC), CUBRC and USA (United Space Alliance) Consultants (The Grey Beards) were asked to independently verify the flight scaling data generated by Boeing for flight certification of the re-designed external tank (ET) components. The blind test comparison showed very good results.

The Standardization of the Clock Drawing Test (CDT) for People with Stroke Using Rasch Analysis

PubMed Central

Yoo, Doo Han; Hong, Deok Gi; Lee, Jae Shin

2014-01-01

[Purpose] The aim of this study was to standardize the clock drawing test (CDT) for people with stroke using Rasch analysis. [Subjects and Methods] Seventeen items of the CDT identified through a literature review were performed by 159 stroke patients. The data was analyzed with Winstep version 3.57 using the Rasch model to examine the unidimensionality of the items’ fit, the distribution of the items’ difficulty, and the reliability and appropriateness of the rating scale. [Result] Ten out of the 159 participations (6.2%) were considered misfit subjects, and one item of the CDT was determined to be a misfit item based on Rasch analysis. The rating scales were judged as suitable because the observed average showed an array of vertical orders and MNSQ values < 2. The separate index and reliability of the subject (1.98, 0.80) and item (6.45, 0.97) showed relatively high values. [Conclusion] This study is the first to examine the CDT scale in stroke patients by Rasch analysis. The CDT is expected to be useful for screening stroke patients with cognitive problems. PMID:24409026

Normative Data for an Instrumental Assessment of the Upper-Limb Functionality.

PubMed

Caimmi, Marco; Guanziroli, Eleonora; Malosio, Matteo; Pedrocchi, Nicola; Vicentini, Federico; Molinari Tosatti, Lorenzo; Molteni, Franco

2015-01-01

Upper-limb movement analysis is important to monitor objectively rehabilitation interventions, contributing to improving the overall treatments outcomes. Simple, fast, easy-to-use, and applicable methods are required to allow routinely functional evaluation of patients with different pathologies and clinical conditions. This paper describes the Reaching and Hand-to-Mouth Evaluation Method, a fast procedure to assess the upper-limb motor control and functional ability, providing a set of normative data from 42 healthy subjects of different ages, evaluated for both the dominant and the nondominant limb motor performance. Sixteen of them were reevaluated after two weeks to perform test-retest reliability analysis. Data were clustered into three subgroups of different ages to test the method sensitivity to motor control differences. Experimental data show notable test-retest reliability in all tasks. Data from older and younger subjects show significant differences in the measures related to the ability for coordination thus showing the high sensitivity of the method to motor control differences. The presented method, provided with control data from healthy subjects, appears to be a suitable and reliable tool for the upper-limb functional assessment in the clinical environment.

Normative Data for an Instrumental Assessment of the Upper-Limb Functionality

PubMed Central

Caimmi, Marco; Guanziroli, Eleonora; Malosio, Matteo; Pedrocchi, Nicola; Vicentini, Federico; Molinari Tosatti, Lorenzo; Molteni, Franco

2015-01-01

Upper-limb movement analysis is important to monitor objectively rehabilitation interventions, contributing to improving the overall treatments outcomes. Simple, fast, easy-to-use, and applicable methods are required to allow routinely functional evaluation of patients with different pathologies and clinical conditions. This paper describes the Reaching and Hand-to-Mouth Evaluation Method, a fast procedure to assess the upper-limb motor control and functional ability, providing a set of normative data from 42 healthy subjects of different ages, evaluated for both the dominant and the nondominant limb motor performance. Sixteen of them were reevaluated after two weeks to perform test-retest reliability analysis. Data were clustered into three subgroups of different ages to test the method sensitivity to motor control differences. Experimental data show notable test-retest reliability in all tasks. Data from older and younger subjects show significant differences in the measures related to the ability for coordination thus showing the high sensitivity of the method to motor control differences. The presented method, provided with control data from healthy subjects, appears to be a suitable and reliable tool for the upper-limb functional assessment in the clinical environment. PMID:26539500

The Effect of Postmastectomy Radiation Therapy on Breast Implants: Material Analysis on Silicone and Polyurethane Prosthesis.

PubMed

Lo Torto, Federico; Relucenti, Michela; Familiari, Giuseppe; Vaia, Nicola; Casella, Donato; Matassa, Roberto; Miglietta, Selenia; Marinozzi, Franco; Bini, Fabiano; Fratoddi, Ilaria; Sciubba, Fabio; Cassese, Raffaele; Tombolini, Vincenzo; Ribuffo, Diego

2018-05-17

The pathogenic mechanism underlying capsular contracture is still unknown. It is certainly a multifactorial process, resulting from human body reaction, biofilm activation, bacteremic seeding, or silicone exposure. The scope of the present article is to investigate the effect of hypofractionated radiotherapy protocol (2.66 Gy × 16 sessions) both on silicone and polyurethane breast implants. Silicone implants and polyurethane underwent irradiation according to a hypofractionated radiotherapy protocol for the treatment of breast cancer. After irradiation implant shells underwent mechanical, chemical, and microstructural evaluation by means of tensile testing, infrared spectra in attenuated total reflectance mode, nuclear magnetic resonance, and field emission scanning electron microscopy. At superficial analysis, irradiated silicone samples show several visible secondary and tertiary blebs. Polyurethane implants showed an open cell structure, which closely resembles a sponge. Morphological observation of struts from treated polyurethane sample shows a more compact structure, with significantly shorter and thicker struts compared with untreated sample. The infrared spectra in attenuated total reflectance mode spectra of irradiated and control samples were compared either for silicon and polyurethane samples. In the case of silicone-based membranes, treated and control specimens showed similar bands, with little differences in the treated one. Nuclear magnetic resonance spectra on the fraction soluble in CDCl3 support these observations. Tensile tests on silicone samples showed a softer behavior of the treated ones. Tensile tests on Polyurethane samples showed no significant differences. Polyurethane implants seem to be more resistant to radiotherapy damage, whereas silicone prosthesis showed more structural, mechanical, and chemical modifications.

Aeromechanics Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

NASA Technical Reports Server (NTRS)

Bakhle, Milind A.; Reddy, T. S. R.; Coroneos, Rula M.; Min, James B.; Provenza, Andrew J.; Duffy, Kirsten P.; Stefko, George L.; Heinlein, Gregory S.

2018-01-01

A propulsion system with Boundary Layer Ingestion (BLI) has the potential to significantly reduce aircraft engine fuel burn. But a critical challenge is to design a fan that can operate continuously with a persistent BLI distortion without aeromechanical failure -- flutter or high cycle fatigue due to forced response. High-fidelity computational aeromechanics analysis can be very valuable to support the design of a fan that has satisfactory aeromechanic characteristics and good aerodynamic performance and operability. Detailed aeromechanics analyses together with careful monitoring of the test article is necessary to avoid unexpected problems or failures during testing. In the present work, an aeromechanics analysis based on a three-dimensional, time-accurate, Reynolds-averaged Navier-Stokes computational fluid dynamics code is used to study the performance and aeromechanical characteristics of the fan in both circumferentially-uniform and circumferentially-varying distorted flows. Pre-test aeromechanics analyses are used to prepare for the wind tunnel test and comparisons are made with measured blade vibration data after the test. The analysis shows that the fan has low levels of aerodynamic damping at various operating conditions examined. In the test, the fan remained free of flutter except at one near-stall operating condition. Analysis could not be performed at this low mass flow rate operating condition since it fell beyond the limit of numerical stability of the analysis code. The measured resonant forced response at a specific low-response crossing indicated that the analysis under-predicted this response and work is in progress to understand possible sources of differences and to analyze other larger resonant responses. Follow-on work is also planned with a coupled inlet-fan aeromechanics analysis that will more accurately represent the interactions between the fan and BLI distortion.

On Improving the Experiment Methodology in Pedagogical Research

ERIC Educational Resources Information Center

Horakova, Tereza; Houska, Milan

2014-01-01

The paper shows how the methodology for a pedagogical experiment can be improved through including the pre-research stage. If the experiment has the form of a test procedure, an improvement of methodology can be achieved using for example the methods of statistical and didactic analysis of tests which are traditionally used in other areas, i.e.…

Contexts Matter: Two Teachers' Language Arts Instruction in This High-Stakes Era

ERIC Educational Resources Information Center

Dooley, Caitlin McMunn; Assaf, Lori Czop

2009-01-01

This retrospective cross-case analysis compares two fourth-grade language arts teachers' beliefs and practices as they respond to an influx of high-stakes tests, including district-mandated benchmark testing systems. One teacher works in a suburban school, the other in an urban school. Results from the study show that the teachers' beliefs about…

A normal incidence high resolution X-ray telescope for solar coronal observations

NASA Technical Reports Server (NTRS)

Golub, Leon

1987-01-01

The preflight preparation of the multilayer mirror fabrication and testing, integration and testing, and WSMR activities are described. Post-flight analysis shows that all payload systems and subsystems performed well within acceptable limits, with the sole exception of the light-blocking prefilters. Suggested corrective actions were discussed. Refurbishment and reflight are then described.

Foreign Language Analysis and Recognition (FLARe)

DTIC Science & Technology

2016-10-08

10 7 Chinese CER ...Rates ( CERs ) were obtained with each feature set: (1) 19.2%, (2) 17.3%, and (3) 15.3%. Based on these results, a GMM-HMM speech recognition system...These systems were evaluated on the HUB4 and HKUST test partitions. Table 7 shows the CER obtained on each test set. Whereas including the HKUST data

Pupil Mobility, Attainment and Progress in Primary School

ERIC Educational Resources Information Center

Strand, Steve; Demie, Feyisa

2006-01-01

This article presents an analysis of the association between pupil mobility and educational attainment in the 2002 national end of Key Stage 2 (KS2) tests for 11-year-old pupils in an inner London education authority. The results show that pupil mobility is strongly associated with low attainment in the end of key stage tests. However, the…

[Statistical validity of the Mexican Food Security Scale and the Latin American and Caribbean Food Security Scale].

PubMed

Villagómez-Ornelas, Paloma; Hernández-López, Pedro; Carrasco-Enríquez, Brenda; Barrios-Sánchez, Karina; Pérez-Escamilla, Rafael; Melgar-Quiñónez, Hugo

2014-01-01

This article validates the statistical consistency of two food security scales: the Mexican Food Security Scale (EMSA) and the Latin American and Caribbean Food Security Scale (ELCSA). Validity tests were conducted in order to verify that both scales were consistent instruments, conformed by independent, properly calibrated and adequately sorted items, arranged in a continuum of severity. The following tests were developed: sorting of items; Cronbach's alpha analysis; parallelism of prevalence curves; Rasch models; sensitivity analysis through mean differences' hypothesis test. The tests showed that both scales meet the required attributes and are robust statistical instruments for food security measurement. This is relevant given that the lack of access to food indicator, included in multidimensional poverty measurement in Mexico, is calculated with EMSA.

Limit Cycle Analysis Applied to the Oscillations of Decelerating Blunt-Body Entry Vehicles

NASA Technical Reports Server (NTRS)

Schoenenberger, Mark; Queen, Eric M.

2008-01-01

Many blunt-body entry vehicles have nonlinear dynamic stability characteristics that produce self-limiting oscillations in flight. Several different test techniques can be used to extract dynamic aerodynamic coefficients to predict this oscillatory behavior for planetary entry mission design and analysis. Most of these test techniques impose boundary conditions that alter the oscillatory behavior from that seen in flight. Three sets of test conditions, representing three commonly used test techniques, are presented to highlight these effects. Analytical solutions to the constant-coefficient planar equations-of-motion for each case are developed to show how the same blunt body behaves differently depending on the imposed test conditions. The energy equation is applied to further illustrate the governing dynamics. Then, the mean value theorem is applied to the energy rate equation to find the effective damping for an example blunt body with nonlinear, self-limiting dynamic characteristics. This approach is used to predict constant-energy oscillatory behavior and the equilibrium oscillation amplitudes for the various test conditions. These predictions are verified with planar simulations. The analysis presented provides an overview of dynamic stability test techniques and illustrates the effects of dynamic stability, static aerodynamics and test conditions on observed dynamic motions. It is proposed that these effects may be leveraged to develop new test techniques and refine test matrices in future tests to better define the nonlinear functional forms of blunt body dynamic stability curves.

Aquarius Reflector Surface Temperature Monitoring Test and Analysis

NASA Technical Reports Server (NTRS)

Abbott, Jamie; Lee, Siu-Chun; Becker, Ray

2008-01-01

The presentation addresses how to infer the front side temperatures for the Aquarius L-band reflector based upon backside measurement sites. Slides discussing the mission objectives and design details are at the same level found on typical project outreach websites and in conference papers respectively. The test discussion provides modest detail of an ordinary thermal balance test using mockup hardware. The photographs show an off-Lab vacuum chamber facility with no compromising details.

Application of Optical Coherence Tomography and Contrast Sensitivity Test for Observing Fundus Changes of Patients With Pregnancy-Induced Hypertension Syndrome.

PubMed

Wang, Zhixue; Zou, Yuanyuan; Li, Wenying; Wang, Xueyan; Zhang, Min; Wang, Wenying

2015-11-01

This study was aimed to investigate the fundus changes of patients with pregnancy-induced hypertension syndrome (PIHS) using optical coherence tomography (OCT) technology and contrast sensitivity (CS) tests.Ninety-eight patients with PIHS underwent routine eye examinations including vision correction, fundus examination, OCT, and CS tests. The CS test was performed at low, medium, and high frequency, respectively. Moreover, the difference in CS tests between 2 groups was analyzed by independent-samples T test. The Kruskal-Wallis rank sum test and linear regression model were used to detect the correlation of OCT with CS, respectively. Meanwhile Satterthwaite approximate T test was adopted for pairwise comparisons after nonparametric analysis of variance.The OCT test revealed that 56.76% of the examined eyes showed shallow retinal detachment in the macula lutea and around the optic disk. The differences in CS at each spatial frequency between the case and control group were statistically significant (P < 0.01). Besides, OCT manifestations were associated with CS at each spacial frequency including 1.5, 3, 6, 12, and 18 frequency (P < 0.01). And patients with abnormal manifestations of OCT showed lower CS at each spacial frequency than those without abnormal OCT manifestations. What's more the OCT manifestation 1 showed the greatest impact on CS at each spacial frequency.The results showed that abnormal OCT manifestations were correlated with CS in PIHS. OCT and CS tests might be valuable methods in observing fundus changes for PIHS patients.

Static renewal tests using Anodonta imbecillis (freshwater mussels). Anodonta imbecillis QA test 1, Clinch River-Environmental Restoration Program (CR-ERP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simbeck, D.J.

1993-12-31

Toxicity testing of split whole sediment samples using juvenile freshwater mussels (Anodonta imbecillis) was conducted by TVA and CR-ERP personnel as part of the CR-ERP biomonitoring study of Clinch River sediments to provide a quality assurance mechanism for test organism quality and overall performance of the test. In addition, testing included procedures comparing daily renewal versus non-renewal of test sediments. Testing of sediment samples collected July 15 from Poplar Creek Miles 6.0 and 5.1 was conducted from July 21--30, 1993. Results from this test showed no toxicity (survival effects) to fresh-water mussels during a 9-day exposure to the sediments. Sidemore » by side testing of sediments with daily sediment renewal and no sediment renewal showed no differences between methods. This may be due to the absence of toxicity in both samples and may not reflect true differences between the two methods for toxic sediment. Attachments to this report include: Chain of custody forms -- originals; Toxicity test bench sheets and statistical analyses; and Ammonia analysis request and results.« less

Impaired gait pattern as a sensitive tool to assess hypoxic brain damage in a novel mouse model of atherosclerotic plaque rupture.

PubMed

Roth, Lynn; Van Dam, Debby; Van der Donckt, Carole; Schrijvers, Dorien M; Lemmens, Katrien; Van Brussel, Ilse; De Deyn, Peter P; Martinet, Wim; De Meyer, Guido R Y

2015-02-01

Apolipoprotein E deficient (ApoE(-/-)) mice with a heterozygous mutation in the fibrillin-1 gene (Fbn1(C1039G+/-)) show spontaneous atherosclerotic plaque ruptures, disturbances in cerebral flow and sudden death when fed a Western-type diet (WD). The present study focused on motor coordination and spatial learning of ApoE(-/-) Fbn1(C1039G+/-) mice on WD for 20 weeks (n=21). ApoE(-/-) mice on WD (n=24) and ApoE(-/-) Fbn1(C1039G+/-) mice on normal diet (ND, n=21) served as controls. Starting from 10 weeks of diet, coordination was assessed every two weeks by the following tests: gait analysis, stationary beam, wire suspension and accelerating rotarod. The Morris water maze test was performed after 13 weeks of diet to study spatial learning. At the end of the experiment (20 weeks of WD), the mice were sacrificed and the brachiocephalic artery and brain were isolated. From 12 weeks onward, gait analysis of ApoE(-/-) Fbn1(C1039G+/-) mice on WD revealed a progressive increase in track width as compared to ApoE(-/-) mice on WD and ApoE(-/-) Fbn1(C1039G+/-) mice on ND (at 20 weeks: 29.8±0.6 mm vs. 25.8±0.4 mm and 26.0±0.5 mm). Moreover, the stationary beam test showed a decrease in motor coordination of ApoE(-/-) Fbn1(C1039G+/-) mice on WD at 18 and 20 weeks. The wire suspension test and accelerating rotarod could not detect signs of motor impairment. Spatial learning was also not affected. Histological analysis of the brachiocephalic artery showed larger and more stenotic plaques in ApoE(-/-) Fbn1(C1039G+/-) mice on WD. Furthermore, the parietal cortex of ApoE(-/-) Fbn1(C1039G+/-) mice on WD showed pyknotic nuclei as a sign of hypoxia and the percentage of pyknosis correlated with track width. In conclusion, gait analysis may be an efficient method for analyzing hypoxic brain damage in the ApoE(-/-) Fbn1(C1039G+/-) mouse model. This test could be of value to assess the effect of potential anti-atherosclerotic therapies in mice. Copyright © 2014 Elsevier Inc. All rights reserved.

Characterization of shredded television scrap and implications for materials recovery.

PubMed

Cui, Jirang; Forssberg, Eric

2007-01-01

Characterization of TV scrap was carried out by using a variety of methods, such as chemical analysis, particle size and shape analysis, liberation degree analysis, thermogravimetric analysis, sink-float test, and IR spectrometry. A comparison of TV scrap, personal computer scrap, and printed circuit board scrap shows that the content of non-ferrous metals and precious metals in TV scrap is much lower than that in personal computer scrap or printed circuit board scrap. It is expected that recycling of TV scrap will not be cost-effective by utilizing conventional manual disassembly. The result of particle shape analysis indicates that the non-ferrous metal particles in TV scrap formed as a variety of shapes; it is much more heterogeneous than that of plastics and printed circuit boards. Furthermore, the separability of TV scrap using density-based techniques was evaluated by the sink-float test. The result demonstrates that a high recovery of copper could be obtained by using an effective gravity separation process. Identification of plastics shows that the major plastic in TV scrap is high impact polystyrene. Gravity separation of plastics may encounter some challenges in separation of plastics from TV scrap because of specific density variations.

Tensile properties of cooked meat sausages and their correlation with texture profile analysis (TPA) parameters and physico-chemical characteristics.

PubMed

Herrero, A M; de la Hoz, L; Ordóñez, J A; Herranz, B; Romero de Ávila, M D; Cambero, M I

2008-11-01

The possibilities of using breaking strength (BS) and energy to fracture (EF) for monitoring textural properties of some cooked meat sausages (chopped, mortadella and galantines) were studied. Texture profile analysis (TPA), folding test and physico-chemical measurements were also performed. Principal component analysis enabled these meat products to be grouped into three textural profiles which showed significant (p<0.05) differences mainly for BS, hardness, adhesiveness and cohesiveness. Multivariate analysis indicated that BS, EF and TPA parameters were correlated (p<0.05) for every individual meat product (chopped, mortadella and galantines) and all products together. On the basis of these results, TPA parameters could be used for constructing regression models to predict BS. The resulting regression model for all cooked meat products was BS=-0.160+6.600∗cohesiveness-1.255∗adhesiveness+0.048∗hardness-506.31∗springiness (R(2)=0.745, p<0.00005). Simple linear regression analysis showed significant coefficients of determination between BS (R(2)=0.586, p<0.0001) versus folding test grade (FG) and EF versus FG (R(2)=0.564, p<0.0001).

Retention Load of Telescopic Crowns with Different Taper Angles between Cobalt-Chromium and Polyetheretherketone Made with Three Different Manufacturing Processes Examined by Pull-Off Test.

PubMed

Wagner, Christina; Stock, Veronika; Merk, Susanne; Schmidlin, Patrick R; Roos, Malgorzata; Eichberger, Marlis; Stawarczyk, Bogna

2018-02-01

To investigate the retention loads of differently fabricated secondary telescopic polyetheretherketone (PEEK) crowns on cobalt-chromium primary crowns with different tapers. Cobalt-chromium primary crowns with 0°, 1°, and 2° tapers were constructed, milled, and sintered. Corresponding secondary crowns were fabricated by milling, pressing from pellets, and pressing from granules. For these nine test groups, the pull-off tests of each crown combination were performed 20 times, and the retention loads were measured (Zwick 1445, 50 mm/min). Data were analyzed using linear regression, covariance analysis, mixed models, Kruskal-Wallis, and Mann-Whitney U-test, together with the Benferroni-Holm correction. The mixed models covariance analysis reinforced stable retention load values (p = 0.162) for each single test sequence. There was no interaction between the groups and the separation cycles (p = 0.179). Milled secondary crowns with 0° showed the lowest mean retention load values compared to all tested groups (p = 0.003) followed by those pressed form pellets with 1°. Regarding the different tapers, no effect of manufacturing method on the results was observed within 1° and 2° groups (p = 0.540; p = 0.052); however, among the 0° groups, the milled ones showed significantly the lowest retention load values (p = 0.002). Among the manufacturing methods, both pressed groups showed no impact of taper on the retention load values (p > 0.324 and p > 0.123, respectively), whereas among the milled secondary crowns, the 0° taper showed significantly lower retention load values than the 1° and 2° taper (p < 0.002). Based on these results, telescopic crowns made of PEEK seem to show stable retention load values for each test sequence; however, data with thermo-mechanical aging are still required. In addition, further developments in CAD/CAM manufacturing of PEEK materials for telescopic crowns are warranted, especially for 0°. © 2016 by the American College of Prosthodontists.

Tetherless ergonomics workstation to assess nurses' physical workload in a clinical setting.

PubMed

Smith, Warren D; Nave, Michael E; Hreljac, Alan P

2011-01-01

Nurses are at risk of physical injury when moving immobile patients. This paper describes the development and testing of a tetherless ergonomics workstation that is suitable for studying nurses' physical workload in a clinical setting. The workstation uses wearable sensors to record multiple channels of body orientation and muscle activity and wirelessly transmits them to a base station laptop computer for display, storage, and analysis. In preparation for use in a clinical setting, the workstation was tested in a laboratory equipped for multi-camera video motion analysis. The testing included a pilot study of the effect of bed height on student nurses' physical workload while they repositioned a volunteer posing as a bedridden patient toward the head of the bed. Each nurse subject chose a preferred bed height, and data were recorded, in randomized order, with the bed at this height, at 0.1 m below this height, and at 0.1 m above this height. The testing showed that the body orientation recordings made by the wearable sensors agreed closely with those obtained from the video motion analysis system. The pilot study showed the following trends: As the bed height was raised, the nurses' trunk flexion at both thoracic and lumbar sites and lumbar muscle effort decreased, whereas trapezius and deltoid muscle effort increased. These trends will be evaluated by further studies of practicing nurses in the clinical setting.

Comparative evaluation of methods for the determination of heat transfer coefficients of liquid and gaseous quenching media

NASA Astrophysics Data System (ADS)

Shevchenko, Svetlana Yu.; Melnik, Yury A.; Smirnov, Andrey E.; Htet, Wai Yan Min

2018-03-01

Temperature dependences of heat transfer coefficients of liquid and gaseous quenching media were determined using a gradient probe and prismatic probe of more simple design. The probes of two different designs were tested in the same conditions. Analysis of heat transfer coefficients showed good agreement between the data obtained. The tests were carried out with liquid and gaseous quenching media: water, polymer quenchant, quenching oil and high-pressure nitrogen. Methods of mathematical modeling of steel samples quenching show the adequacy of the results.

Thermal-hydraulic analysis of the coil test facility for CFETR.

PubMed

Ren, Yong; Liu, Xiaogang; Li, Junjun; Wang, Zhaoliang; Qiu, Lilong; Du, Shijun; Li, Guoqiang; Gao, Xiang

2016-01-01

Performance test of the China Fusion Engineering Test Reactor (CFETR) central solenoid (CS) and toroidal field (TF) insert coils is of great importance to evaluate the CFETR magnet performance in relevant operation conditions. The superconducting magnet of the coil test facility for CFETR is being designed with the aim of providing a background magnetic field to test the CFETR CS insert and TF insert coils. The superconducting magnet consists of the inner module with Nb 3 Sn coil and the outer module with NbTi coil. The superconducting magnet is designed to have a maximum magnetic field of 12.59 T and a stored energy of 436.6 MJ. An active quench protection circuit and the positive temperature coefficient dump resistor were adopted to transfer the stored magnetic energy. The temperature margin behavior of the test facility for CFETR satisfies the design criteria. The quench analysis of the test facility shows that the cable temperature and the helium pressure inside the jacket are within the design criteria.

Countermeasures for Reducing Unsteady Aerodynamic Force Acting on High-Speed Train in Tunnel by Use of Modifications of Train Shapes

NASA Astrophysics Data System (ADS)

Suzuki, Masahiro; Nakade, Koji; Ido, Atsushi

As the maximum speed of high-speed trains increases, flow-induced vibration of trains in tunnels has become a subject of discussion in Japan. In this paper, we report the result of a study on use of modifications of train shapes as a countermeasure for reducing an unsteady aerodynamic force by on-track tests and a wind tunnel test. First, we conduct a statistical analysis of on-track test data to identify exterior parts of a train which cause the unsteady aerodynamic force. Next, we carry out a wind tunnel test to measure the unsteady aerodynamic force acting on a train in a tunnel and examined train shapes with a particular emphasis on the exterior parts identified by the statistical analysis. The wind tunnel test shows that fins under the car body are effective in reducing the unsteady aerodynamic force. Finally, we test the fins by an on-track test and confirmed its effectiveness.

On sample size of the kruskal-wallis test with application to a mouse peritoneal cavity study.

PubMed

Fan, Chunpeng; Zhang, Donghui; Zhang, Cun-Hui

2011-03-01

As the nonparametric generalization of the one-way analysis of variance model, the Kruskal-Wallis test applies when the goal is to test the difference between multiple samples and the underlying population distributions are nonnormal or unknown. Although the Kruskal-Wallis test has been widely used for data analysis, power and sample size methods for this test have been investigated to a much lesser extent. This article proposes new power and sample size calculation methods for the Kruskal-Wallis test based on the pilot study in either a completely nonparametric model or a semiparametric location model. No assumption is made on the shape of the underlying population distributions. Simulation results show that, in terms of sample size calculation for the Kruskal-Wallis test, the proposed methods are more reliable and preferable to some more traditional methods. A mouse peritoneal cavity study is used to demonstrate the application of the methods. © 2010, The International Biometric Society.

Embryotoxic and pharmacologic potency ranking of six azoles in the rat whole embryo culture by morphological and transcriptomic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dimopoulou, Myrto, E-mail: myrto.dimopoulou@wur.nl

Differential gene expression analysis in the rat whole embryo culture (WEC) assay provides mechanistic insight into the embryotoxicity of test compounds. In our study, we hypothesized that comparative analysis of the transcriptomes of rat embryos exposed to six azoles (flusilazole, triadimefon, ketoconazole, miconazole, difenoconazole and prothioconazole) could lead to a better mechanism-based understanding of their embryotoxicity and pharmacological action. For evaluating embryotoxicity, we applied the total morphological scoring system (TMS) in embryos exposed for 48 h. The compounds tested showed embryotoxicity in a dose-response fashion. Functional analysis of differential gene expression after 4 h exposure at the ID{sub 10} (effectivemore » dose for 10% decreased TMS), revealed the sterol biosynthesis pathway and embryonic development genes, dominated by genes in the retinoic acid (RA) pathway, albeit in a differential way. Flusilazole, ketoconazole and triadimefon were the most potent compounds affecting the RA pathway, while in terms of regulation of sterol function, difenoconazole and ketoconazole showed the most pronounced effects. Dose-dependent analysis of the effects of flusilazole revealed that the RA pathway related genes were already differentially expressed at low dose levels while the sterol pathway showed strong regulation at higher embryotoxic doses, suggesting that this pathway is less predictive for the observed embryotoxicity. A similar analysis at the 24-hour time point indicated an additional time-dependent difference in the aforementioned pathways regulated by flusilazole. In summary, the rat WEC assay in combination with transcriptomics could add a mechanistic insight into the embryotoxic potency ranking and pharmacological mode of action of the tested compounds. - Highlights: • Embryonic exposure to azoles revealed concentration-dependent malformations. • Transcriptomics could enhance the mechanistic knowledge of embryotoxicants. • Retinoic acid gene set identifies early embryotoxic responses to azoles. • Toxic versus pharmacologic potency determines functional efficacy.« less

The Impact of Problem Sets on Student Learning

ERIC Educational Resources Information Center

Kim, Myeong Hwan; Cho, Moon-Heum; Leonard, Karen Moustafa

2012-01-01

The authors examined the role of problem sets on student learning in university microeconomics. A total of 126 students participated in the study in consecutive years. independent samples t test showed that students who were not given answer keys outperformed students who were given answer keys. Multiple regression analysis showed that, along with…

Service evaluation of an educational intervention to improve sexual health services in primary care implemented using a step-wedge design: analysis of chlamydia testing and diagnosis rate changes.

PubMed

Town, Katy; McNulty, Cliodna A M; Ricketts, Ellie J; Hartney, Thomas; Nardone, Anthony; Folkard, Kate A; Charlett, Andre; Dunbar, J Kevin

2016-08-02

Providing sexual health services in primary care is an essential step towards universal provision. However they are not offered consistently. We conducted a national pilot of an educational intervention to improve staff's skills and confidence to increase chlamydia testing rates and provide condoms with contraceptive information plus HIV testing according to national guidelines, known as 3Cs&HIV. The effectiveness of the pilot on chlamydia testing and diagnosis rates in general practice was evaluated. The pilot was implemented using a step-wedge design over three phases during 2013 and 2014 in England. The intervention combined educational workshops with posters, testing performance feedback and continuous support. Chlamydia testing and diagnosis rates in participating general practices during the control and intervention periods were compared adjusting for seasonal trends in chlamydia testing and differences in practice size. Intervention effect modification was assessed for the following general practice characteristics: chlamydia testing rate compared to national median, number of general practice staff employed, payment for chlamydia screening, practice urban/rurality classification, and proximity to sexual health clinics. The 460 participating practices conducted 26,021 tests in the control period and 18,797 tests during the intervention period. Intention-to-treat analysis showed no change in the unadjusted median tests and diagnoses per month per practice after receiving training: 2.7 vs 2.7; 0.1 vs 0.1. Multivariable negative binomial regression analysis found no significant change in overall testing or diagnoses post-intervention (incidence rate ratio (IRR) 1.01, 95 % confidence interval (CI) 0.96-1.07, P = 0.72; 0.98 CI 0.84-1.15, P = 0.84, respectively). Stratified analysis showed testing increased significantly in practices where payments were in place prior to the intervention (IRR 2.12 CI 1.41-3.18, P < 0.001) and in practices with 6-15 staff (6-10 GPs IRR 1.35 (1.07-1.71), P = 0.012; 11-15 GPs IRR 1.37 (1.09-1.73), P = 0.007). This national pilot of short educational training sessions found no overall effect on chlamydia testing in primary care. However, in certain sub-groups chlamydia testing rates increased due to the intervention. This demonstrates the importance of piloting and evaluating any service improvement intervention to assess the impact before widespread implementation, and the need for detailed understanding of local services in order to select effective interventions.

Space Pomology: Dwarf Plums for Fresh Food Production

NASA Technical Reports Server (NTRS)

Spencer, LaShelle; Graham, Thomas; Stutte, Gary; Massa, Gioia; Mickens, Matthew; Wheeler, Raymond

2017-01-01

Recently, USDA ARS researchers genetically modified plums for rapid breeding work and noticed the plants could flower and develop fruit rapidly on relatively small plants. We have tested several of these genetically modified (GM) plums in plant chambers to assess their potential as a space crop. We have been able to clone these genetic lines using cuttings that are rooted using growth regulating compounds. Results showed that the GM plums indeed flower and fruit on small plants in controlled environments similar to what might be used in space, but they require cross-pollination with pollen from a standard plum. Analysis of stomatal conductance and leaf transpiration showed that water use went up in the light period, as expected, and but that GM types typically showed higher conductance than a standard plum. Analysis of tissue showed that fruit could be a good source of potassium and phenolic compounds, which could be beneficial as a bone loss countermeasure (Smith et al., 2014). These findings are all promising for using dwarf GM plums as a supplemental food for space, but further horticultural testing is needed before they are ready.

Analysis of the Astronomy Diagnostic Test

NASA Astrophysics Data System (ADS)

Brogt, Erik; Sabers, Darrell; Prather, Edward E.; Deming, Grace L.; Hufnagel, Beth; Slater, Timothy F.

Seventy undergraduate class sections were examined from the database of Astronomy Diagnostic Test (ADT) results of Deming and Hufnagel to determine if course format correlated with ADT normalized gain scores. Normalized gains were calculated for four different classroom scenarios: lecture, lecture with discussion, lecture with lab, and lecture with both lab and discussion. Statistical analysis shows that there are no significant differences in normalized gain among the self- reported classroom formats. Prerequisites related to mathematics courses did show differences in normalized gain. Of all reported course activities, only the lecture and the readings for the course correlate significantly with the normalized gain. This analysis suggests that the ADT may not have enough sensitivity to measure differences in the effectiveness of different course formats because of the wide range of topics that the ADT addresses with few questions. Different measures of gain and their biases are discussed. We argue that the use of the normalized gain is not always warranted because of its strong bias toward high pretest scores.

[Simulation and data analysis of stereological modeling based on virtual slices].

PubMed

Wang, Hao; Shen, Hong; Bai, Xiao-yan

2008-05-01

To establish a computer-assisted stereological model for simulating the process of slice section and evaluate the relationship between section surface and estimated three-dimensional structure. The model was designed by mathematic method as a win32 software based on the MFC using Microsoft visual studio as IDE for simulating the infinite process of sections and analysis of the data derived from the model. The linearity of the fitting of the model was evaluated by comparison with the traditional formula. The win32 software based on this algorithm allowed random sectioning of the particles distributed randomly in an ideal virtual cube. The stereological parameters showed very high throughput (>94.5% and 92%) in homogeneity and independence tests. The data of density, shape and size of the section were tested to conform to normal distribution. The output of the model and that from the image analysis system showed statistical correlation and consistency. The algorithm we described can be used for evaluating the stereologic parameters of the structure of tissue slices.

Metallographic Analysis of Brush Bristle and Integrity Testing of Brush Seal in Shroud Ring of T-700 Engine

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Griffin, Thomas A.; Bobula, George A.; Bill, Robert C.; Hull, David R.; Csavina, Kristine R.

1995-01-01

Post-test investigation of a T-700 engine brush seal found regions void of bristles ('yanked out'), regions of bent-over bristles near the inlet, some 'snapped' bristles near the fence, and a more uniform 'smeared' bristle interface between the first and last axial rows of bristles. Several bristles were cut from the brush seal, wax mounted, polished, and analyzed. Metallographic analysis of the bristles near the rub tip showed tungsten-rich phases uniformly distributed throughout the bristle with no apparent change within 1 to 2 micron of the interface except for possibly a small amount of titanium, which would represent a transfer from the rotor. Analysis of the bristle wear face showed nonuniform tungsten, which is indicative of material resolidification. The cut end contained oxides and internal fractures; the worn end was covered with oxide scale. Material losses due to wear and elastoplastic deformation within the shear zone and third-body lubrication effects in the contact zone are discussed.

A study of tensile test on open-cell aluminum foam sandwich

NASA Astrophysics Data System (ADS)

Ibrahim, N. A.; Hazza, M. H. F. Al; Adesta, E. Y. T.; Abdullah Sidek, Atiah Bt.; Endut, N. A.

2018-01-01

Aluminum foam sandwich (AFS) panels are one of the growing materials in the various industries because of its lightweight behavior. AFS also known for having excellent stiffness to weight ratio and high-energy absorption. Due to their advantages, many researchers’ shows an interest in aluminum foam material for expanding the use of foam structure. However, there is still a gap need to be fill in order to develop reliable data on mechanical behavior of AFS with different parameters and analysis method approach. Least of researcher focusing on open-cell aluminum foam and statistical analysis. Thus, this research conducted by using open-cell aluminum foam core grade 6101 with aluminum sheets skin tested under tension. The data is analyzed using full factorial in JMP statistical analysis software (version 11). ANOVA result show a significant value of the model which less than 0.500. While scatter diagram and 3D plot surface profiler found that skins thickness gives a significant impact to stress/strain value compared to core thickness.

Monitoring the vernal advancement and retrogradation (green wave effect) of natural vegetation

NASA Technical Reports Server (NTRS)

Rouse, J. W., Jr. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Preliminary evaluation of autumnal phase ground truth data suggests that the sampling procedures at the Great Plains Corridor network test sites are adequate to show relatively small temporal changes in above-ground vegetation biomass and vegetation condition. Vegetation changes measured August through December, reflect grazing intensity and environmental conditions at the test sites. Preliminary analysis of black and white imagery suggests that detail in vegetation patterns is much greater than originally anticipated. A first look analysis of single band imagery and digital data at two locations shows that woodland, grassland, and cropland areas are easily delineated. Computer derived grey-scale maps from MSS digital data were shown to be useful in identifying the location of small fields and features of the natural and cultivated lands. Single band imagery and digital data are believed to have important application for synoptic land use mapping and inventory. Initial ratio analysis, using band 5 and 7 data, suggests the applicability in the greenness of a vegetative scene.

Climate Informed Low Flow Frequency Analysis Using Nonstationary Modeling

NASA Astrophysics Data System (ADS)

Liu, D.; Guo, S.; Lian, Y.

2014-12-01

Stationarity is often assumed for frequency analysis of low flows in water resources management and planning. However, many studies have shown that flow characteristics, particularly the frequency spectrum of extreme hydrologic events,were modified by climate change and human activities and the conventional frequency analysis without considering the non-stationary characteristics may lead to costly design. The analysis presented in this paper was based on the more than 100 years of daily flow data from the Yichang gaging station 44 kilometers downstream of the Three Gorges Dam. The Mann-Kendall trend test under the scaling hypothesis showed that the annual low flows had significant monotonic trend, whereas an abrupt change point was identified in 1936 by the Pettitt test. The climate informed low flow frequency analysis and the divided and combined method are employed to account for the impacts from related climate variables and the nonstationarities in annual low flows. Without prior knowledge of the probability density function for the gaging station, six distribution functions including the Generalized Extreme Values (GEV), Pearson Type III, Gumbel, Gamma, Lognormal, and Weibull distributions have been tested to find the best fit, in which the local likelihood method is used to estimate the parameters. Analyses show that GEV had the best fit for the observed low flows. This study has also shown that the climate informed low flow frequency analysis is able to exploit the link between climate indices and low flows, which would account for the dynamic feature for reservoir management and provide more accurate and reliable designs for infrastructure and water supply.

Cognitive Stimulation of Elderly Residents in Social Protection Centers in Cartagena, 2014.

PubMed

Melguizo Herrera, Estela; Bertel De La Hoz, Anyel; Paternina Osorio, Diego; Felfle Fuentes, Yurani; Porto Osorio, Leidy

To determine the effectiveness of a program of cognitive stimulation of the elderly residents in Social Protection Centers in Cartagena, 2014. Quasi-experimental study with pre and post tests in control and experimental groups. A sample of 37 elderly residents in Social Protection Centers participated: 23 in the experimental group and 14 in the control group. A survey and a mental evaluation test (Pfeiffer) were applied. The experimental group participated in 10 sessions of cognitive stimulation. The paired t-test showed statistically significant differences in the Pfeiffer test, pre and post intervention, compared to the experimental group (P=.0005). The unpaired t-test showed statistically significant differences in Pfeiffer test results to the experimental and control groups (P=.0450). The analysis of the main components showed that more interrelated variables were: age, diseases, number of errors and test results; which were grouped around the disease variable, with a negative association. The intervention demonstrated a statistically significant improvement in cognitive functionality of the elderly. Nursing can lead this type of intervention. It should be studied further to strengthen and clarify these results. Copyright © 2016 Asociación Colombiana de Psiquiatría. Publicado por Elsevier España. All rights reserved.

Loading tests of a wing structure for a hypersonic aircraft

NASA Technical Reports Server (NTRS)

Fields, R. A.; Reardon, L. F.; Siegel, W. H.

1980-01-01

Room-temperature loading tests were conducted on a wing structure designed with a beaded panel concept for a Mach 8 hypersonic research airplane. Strain, stress, and deflection data were compared with the results of three finite-element structural analysis computer programs and with design data. The test program data were used to evaluate the structural concept and the methods of analysis used in the design. A force stiffness technique was utilized in conjunction with load conditions which produced various combinations of panel shear and compression loading to determine the failure envelope of the buckling critical beaded panels The force-stiffness data did not result in any predictions of buckling failure. It was, therefore, concluded that the panels were conservatively designed as a result of design constraints and assumptions of panel eccentricities. The analysis programs calculated strains and stresses competently. Comparisons between calculated and measured structural deflections showed good agreement. The test program offered a positive demonstration of the beaded panel concept subjected to room-temperature load conditions.

Simultaneous detection of antibodies to five Actinobacillus pleuropneumoniae serovars using bead-based multiplex analysis.

PubMed

Berger, Sanne Schou; Lauritsen, Klara Tølbøll; Boas, Ulrik; Lind, Peter; Andresen, Lars Ole

2017-11-01

We developed and made a preliminary validation of a bead-based multiplexed immunoassay for simultaneous detection of porcine serum antibodies to Actinobacillus pleuropneumoniae serovars 1, 2, 6, 7, and 12. Magnetic fluorescent beads were coupled with A. pleuropneumoniae antigens and tested with a panel of serum samples from experimentally infected pigs and with serum samples from uninfected and naturally infected pigs. The multiplex assay was compared to in-house ELISAs and complement fixation (CF) tests, which have been used for decades as tools for herd classification in the Danish Specific Pathogen Free system. Assay specificities and sensitivities as well as the corresponding cutoff values were determined using receiver operating characteristic (ROC) curve analysis, and the A. pleuropneumoniae multiplex assay showed good correlation with the in-house ELISAs and CF tests with areas under ROC curves ≥ 0.988. Benefits of multiplexed assays compared to ELISAs and CF tests include reduced serum sample volumes needed for analysis, less labor, and shorter assay time.

Ares-I-X Stability and Control Flight Test: Analysis and Plans

NASA Technical Reports Server (NTRS)

Brandon, Jay M.; Derry, Stephen D.; Heim, Eugene H.; Hueschen, Richard M.; Bacon, Barton J.

2008-01-01

The flight test of the Ares I-X vehicle provides a unique opportunity to reduce risk of the design of the Ares I vehicle and test out design, math modeling, and analysis methods. One of the key features of the Ares I design is the significant static aerodynamic instability coupled with the relatively flexible vehicle - potentially resulting in a challenging controls problem to provide adequate flight path performance while also providing adequate structural mode damping and preventing adverse control coupling to the flexible structural modes. Another challenge is to obtain enough data from the single flight to be able to conduct analysis showing the effectiveness of the controls solutions and have data to inform design decisions for Ares I. This paper will outline the modeling approaches and control system design to conduct this flight test, and also the system identification techniques developed to extract key information such as control system performance (gain/phase margins, for example), structural dynamics responses, and aerodynamic model estimations.

Rocket-Based Combined Cycle Engine Technology Development: Inlet CFD Validation and Application

NASA Technical Reports Server (NTRS)

DeBonis, J. R.; Yungster, S.

1996-01-01

A CFD methodology has been developed for inlet analyses of Rocket-Based Combined Cycle (RBCC) Engines. A full Navier-Stokes analysis code, NPARC, was used in conjunction with pre- and post-processing tools to obtain a complete description of the flow field and integrated inlet performance. This methodology was developed and validated using results from a subscale test of the inlet to a RBCC 'Strut-Jet' engine performed in the NASA Lewis 1 x 1 ft. supersonic wind tunnel. Results obtained from this study include analyses at flight Mach numbers of 5 and 6 for super-critical operating conditions. These results showed excellent agreement with experimental data. The analysis tools were also used to obtain pre-test performance and operability predictions for the RBCC demonstrator engine planned for testing in the NASA Lewis Hypersonic Test Facility. This analysis calculated the baseline fuel-off internal force of the engine which is needed to determine the net thrust with fuel on.

Microtomography evaluation of dental tissue wear surface induced by in vitro simulated chewing cycles on human and composite teeth.

PubMed

Bedini, Rossella; Pecci, Raffaella; Notarangelo, Gianluca; Zuppante, Francesca; Persico, Salvatore; Di Carlo, Fabio

2012-01-01

In this study a 3D microtomography display of tooth surfaces after in vitro dental wear tests has been obtained. Natural teeth have been compared with prosthetic teeth, manufactured by three different polyceramic composite materials. The prosthetic dental element samples, similar to molars, have been placed in opposition to human teeth extracted by paradontology diseases. After microtomography analysis, samples have been subjected to in vitro fatigue test cycles by servo-hydraulic mechanical testing machine. After the fatigue test, each sample has been subjected again to microtomography analysis to obtain volumetric value changes and dental wear surface images. Wear surface images were obtained by 3D reconstruction software and volumetric value changes were measured by CT analyser software. The aim of this work has been to show the potential of microtomography technique to display very clear and reliable wear surface images. Microtomography analysis methods to evaluate volumetric value changes have been used to quantify dental tissue and composite material wear.

Creep-Fatigue Interaction and Cyclic Strain Analysis in P92 Steel Based on Test

NASA Astrophysics Data System (ADS)

Ji, Dongmei; Zhang, Lai-Chang; Ren, Jianxing; Wang, Dexian

2015-04-01

This work focused on the interaction of creep and fatigue and cyclic strain analysis in high-chromium ferritic P92 steel based on load-controlled creep-fatigue (CF) tests and conventional creep test at 873 K. Mechanical testing shows that the cyclic load inhibits the propagation of creep damage in the P92 steel and CF interaction becomes more severe with the decrease in the holding period duration and stress ratio. These results are also verified by the analysis of cyclic strain. The fatigue lifetime reduces with the increasing of the holding period duration and it does not reduce much with the increasing stress ratio especially under the conditions of long holding period duration. The cyclic strains (i.e., the strain range and creep strain) of CF tests consist of three stages, which is the same as those for the conventional creep behavior. The microscopic fracture surface observations illustrated that two different kinds of voids are observed at the fracture surfaces and Laves phase precipitates at the bottom of the voids.

The Evaluation of Damage Effects on MgO Added Concrete with Slag Cement Exposed to Calcium Chloride Deicing Salt

PubMed Central

Jang, Jae-Kyeong; Kim, Hong-Gi; Kim, Jun-Hyeong

2018-01-01

Concrete systems exposed to deicers are damaged in physical and chemical ways. In mitigating the damage from CaCl2 deicers, the usage of ground slag cement and MgO are investigated. Ordinary Portland cement (OPC) and slag cement are used in different proportions as the binding material, and MgO in doses of 0%, 5%, 7%, and 10% are added to the systems. After 28 days of water-curing, the specimens are immersed in 30% CaCl2 solution by mass for 180 days. Compressive strength test, carbonation test, chloride penetration test, chloride content test, XRD analysis, and SEM-EDAX analysis are conducted to evaluate the damage effects of the deicing solution. Up to 28 days, plain specimens with increasing MgO show a decrease in compressive strength, an increase in carbonation resistance, and a decrease in chloride penetration resistance, whereas the S30- and S50- specimens show a slight increase in compressive strength, an increase in carbonation resistance, and a slight increase in chloride penetration resistance. After 180 days of immersion in deicing solution, specimens with MgO retain their compressive strength longer and show improved durability. Furthermore, the addition of MgO to concrete systems with slag cement induces the formation of magnesium silicate hydrate (M-S-H) phases. PMID:29758008

Polycaprolactone nanofibres loaded with 20(S)-protopanaxadiol for in vitro and in vivo anti-tumour activity study

PubMed Central

Liu, Dan-qing; Cheng, Zhi-qiang; Feng, Qing-jie; Li, He-jie; Ye, Shu-feng

2018-01-01

In this work, 20(S)-protopanaxadiol (PPD)-loaded polycaprolactone (PCL) nanofibres were successfully fabricated by the electrospinning technique using Tween 80 as a solubilizer. Firstly, smooth and continuous nanofibres were collected using suitable solvents and appropriate spinning conditions. Secondly, nanofibre mats were characterized by scanning electron microscopy, thermogravimetric (TG) analysis, Fourier transform infrared spectroscopy and mechanical testing. Finally, nanofibrous membranes were evaluated using water contact angle, in vitro drug release, biodegradation test, in vitro and in vivo anti-tumour activity and cell apoptosis assay. Scanning electron microscopic observations indicated that the diameter of the drug-loaded nanofibres increased with the increase of drug concentration. TG analysis and mechanical test showed that nanofibres were equipped with great thermal and mechanical properties. Biodegradation test exhibited that the structure of fabricated nanofibres had a certain degree of change after 15 days. An in vitro release study showed that PPD from drug-loaded nanofibres could be released in a sustained and prolonged mode. The cytotoxic effect of drug-loaded nanofibre mats examined on human laryngeal carcinoma cells (Hep-2 cells) demonstrated that the prepared nanofibres had a remarkable anti-tumour effect. Meanwhile, the drug-loaded fibre mats showed a super anti-tumour effect in an in vivo anti-tumour study. All in all, PCL nanofibres could be a potential carrier of PPD for cancer treatment. PMID:29892448

Integrating Oil Debris and Vibration Gear Damage Detection Technologies Using Fuzzy Logic

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Afjeh, Abdollah A.

2002-01-01

A diagnostic tool for detecting damage to spur gears was developed. Two different measurement technologies, wear debris analysis and vibration, were integrated into a health monitoring system for detecting surface fatigue pitting damage on gears. This integrated system showed improved detection and decision-making capabilities as compared to using individual measurement technologies. This diagnostic tool was developed and evaluated experimentally by collecting vibration and oil debris data from fatigue tests performed in the NASA Glenn Spur Gear Fatigue Test Rig. Experimental data were collected during experiments performed in this test rig with and without pitting. Results show combining the two measurement technologies improves the detection of pitting damage on spur gears.

Measurement of fracture toughness of metallic materials produced by additive manufacturing

NASA Astrophysics Data System (ADS)

Quénard, O.; Dorival, O.; Guy, Ph.; Votié, A.; Brethome, K.

2018-04-01

This study focuses on the microstructure and mechanical properties of metallic materials produced by additive layer manufacturing (ALM), especially the laser beam melting process. The influence of the specimen orientation during the ALM process and that of two post-build thermal treatments were investigated. The identified metal powder is Ti-6Al-4V (titanium base). Metallographic analysis shows their effects on the microstructure of the metals. Mechanical experiments involving tensile tests as well as toughness tests were performed according to ASTM (American Society for Testing and Materials) norms. The results show that the main influence is that of the thermal treatments; however the manufacturing stacking direction may lead to some anisotropy in the mechanical properties.

Validity of Bioelectrical Impedance Analysis to Estimation Fat-Free Mass in the Army Cadets.

PubMed

Langer, Raquel D; Borges, Juliano H; Pascoa, Mauro A; Cirolini, Vagner X; Guerra-Júnior, Gil; Gonçalves, Ezequiel M

2016-03-11

Bioelectrical Impedance Analysis (BIA) is a fast, practical, non-invasive, and frequently used method for fat-free mass (FFM) estimation. The aims of this study were to validate predictive equations of BIA to FFM estimation in Army cadets and to develop and validate a specific BIA equation for this population. A total of 396 males, Brazilian Army cadets, aged 17-24 years were included. The study used eight published predictive BIA equations, a specific equation in FFM estimation, and dual-energy X-ray absorptiometry (DXA) as a reference method. Student's t-test (for paired sample), linear regression analysis, and Bland-Altman method were used to test the validity of the BIA equations. Predictive BIA equations showed significant differences in FFM compared to DXA (p < 0.05) and large limits of agreement by Bland-Altman. Predictive BIA equations explained 68% to 88% of FFM variance. Specific BIA equations showed no significant differences in FFM, compared to DXA values. Published BIA predictive equations showed poor accuracy in this sample. The specific BIA equations, developed in this study, demonstrated validity for this sample, although should be used with caution in samples with a large range of FFM.

[Japanese learners' processing time for reading English relative clauses analyzed in relation to their English listening proficiency].

PubMed

Oyama, Yoshinori

2011-06-01

The present study examined Japanese university students' processing time for English subject and object relative clauses in relation to their English listening proficiency. In Analysis 1, the relation between English listening proficiency and reading span test scores was analyzed. The results showed that the high and low listening comprehension groups' reading span test scores do not differ. Analysis 2 investigated English listening proficiency and processing time for sentences with subject and object relative clauses. The results showed that reading the relative clause ending and the main verb section of a sentence with an object relative clause (such as "attacked" and "admitted" in the sentence "The reporter that the senator attacked admitted the error") takes less time for learners with high English listening scores than for learners with low English listening scores. In Analysis 3, English listening proficiency and comprehension accuracy for sentences with subject and object relative clauses were examined. The results showed no significant difference in comprehension accuracy between the high and low listening-comprehension groups. These results indicate that processing time for English relative clauses is related to the cognitive processes involved in listening comprehension, which requires immediate processing of syntactically complex audio information.

Comparison of measured and calculated dynamic loads for the Mod-2 2.5 mW wind turbine system

NASA Technical Reports Server (NTRS)

Zimmerman, D. K.; Shipley, S. A.; Miller, R. D.

1995-01-01

The Boeing Company, under contract to the Electric Power Research Institute (EPRI), has completed a test program on the Mod-2 wind turbines at Goodnoe Hills, Washington. The objectives were to update fatigue load spectra, discern site and machine differences, measure vortex generator effects, and to evaluate rotational sampling techniques. This paper shows the test setup and loads instrumentation, loads data comparisons and test/analysis correlations. Test data are correlated with DYLOSAT predictions using both the NASA interim turbulence model and rotationally sampled winds as inputs. The latter is demonstrated to have the potential to improve the test/analysis correlations. The paper concludes with an assessment of the importance of vortex generators, site dependence, and machine differences on fatigue loads. The adequacy of prediction techniques used are evaluated and recommendations are made for improvements to the methodology.

The Relationship between Central Auditory Processing, Language, and Cognition in Children Being Evaluated for Central Auditory Processing Disorder.

PubMed

Brenneman, Lauren; Cash, Elizabeth; Chermak, Gail D; Guenette, Linda; Masters, Gay; Musiek, Frank E; Brown, Mallory; Ceruti, Julianne; Fitzegerald, Krista; Geissler, Kristin; Gonzalez, Jennifer; Weihing, Jeffrey

2017-09-01

Pediatric central auditory processing disorder (CAPD) is frequently comorbid with other childhood disorders. However, few studies have examined the relationship between commonly used CAPD, language, and cognition tests within the same sample. The present study examined the relationship between diagnostic CAPD tests and "gold standard" measures of language and cognitive ability, the Clinical Evaluation of Language Fundamentals (CELF) and the Wechsler Intelligence Scale for Children (WISC). A retrospective study. Twenty-seven patients referred for CAPD testing who scored average or better on the CELF and low average or better on the WISC were initially included. Seven children who scored below the CELF and/or WISC inclusion criteria were then added to the dataset for a second analysis, yielding a sample size of 34. Participants were administered a CAPD battery that included at least the following three CAPD tests: Frequency Patterns (FP), Dichotic Digits (DD), and Competing Sentences (CS). In addition, they were administered the CELF and WISC. Relationships between scores on CAPD, language (CELF), and cognition (WISC) tests were examined using correlation analysis. DD and FP showed significant correlations with Full Scale Intelligence Quotient, and the DD left ear and the DD interaural difference measures both showed significant correlations with working memory. However, ∼80% or more of the variance in these CAPD tests was unexplained by language and cognition measures. Language and cognition measures were more strongly correlated with each other than were the CAPD tests with any CELF or WISC scale. Additional correlations with the CAPD tests were revealed when patients who scored in the mild-moderate deficit range on the CELF and/or in the borderline low intellectual functioning range on the WISC were included in the analysis. While both the DD and FP tests showed significant correlations with one or more cognition measures, the majority of the variance in these CAPD measures went unexplained by cognition. Unlike DD and FP, the CS test was not correlated with cognition. Additionally, language measures were not significantly correlated with any of the CAPD tests. Our findings emphasize that the outcomes and interpretation of results vary as a function of the subject inclusion criteria that are applied for the CELF and WISC. Including participants with poorer cognition and/or language scores increased the number of significant correlations observed. For this reason, it is important that studies investigating the relationship between CAPD and other domains or disorders report the specific inclusion criteria used for all tests. American Academy of Audiology

Item Response Theory analysis of Fagerström Test for Cigarette Dependence.

PubMed

Svicher, Andrea; Cosci, Fiammetta; Giannini, Marco; Pistelli, Francesco; Fagerström, Karl

2018-02-01

The Fagerström Test for Cigarette Dependence (FTCD) and the Heaviness of Smoking Index (HSI) are the gold standard measures to assess cigarette dependence. However, FTCD reliability and factor structure have been questioned and HSI psychometric properties are in need of further investigations. The present study examined the psychometrics properties of the FTCD and the HSI via the Item Response Theory. The study was a secondary analysis of data collected in 862 Italian daily smokers. Confirmatory factor analysis was run to evaluate the dimensionality of FTCD. A Grade Response Model was applied to FTCD and HSI to verify the fit to the data. Both item and test functioning were analyzed and item statistics, Test Information Function, and scale reliabilities were calculated. Mokken Scale Analysis was applied to estimate homogeneity and Loevinger's coefficients were calculated. The FTCD showed unidimensionality and homogeneity for most of the items and for the total score. It also showed high sensitivity and good reliability from medium to high levels of cigarette dependence, although problems related to some items (i.e., items 3 and 5) were evident. HSI had good homogeneity, adequate item functioning, and high reliability from medium to high levels of cigarette dependence. Significant Differential Item Functioning was found for items 1, 4, 5 of the FTCD and for both items of HSI. HSI seems highly recommended in clinical settings addressed to heavy smokers while FTCD would be better used in smokers with a level of cigarette dependence ranging between low and high. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Reliability and validity of the Braden Scale for predicting pressure sore risk].

PubMed

Boes, C

2000-12-01

For more accurate and objective pressure sore risk assessment various risk assessment tools were developed mainly in the USA and Great Britain. The Braden Scale for Predicting Pressure Sore Risk is one such example. By means of a literature analysis of German and English texts referring to the Braden Scale the scientific control criteria reliability and validity will be traced and consequences for application of the scale in Germany will be demonstrated. Analysis of 4 reliability studies shows an exclusive focus on interrater reliability. Further, even though examination of 19 validity studies occurs in many different settings, such examination is limited to the criteria sensitivity and specificity (accuracy). The range of sensitivity and specificity level is 35-100%. The recommended cut off points rank in the field of 10 to 19 points. The studies prove to be not comparable with each other. Furthermore, distortions in these studies can be found which affect accuracy of the scale. The results of the here presented analysis show an insufficient proof for reliability and validity in the American studies. In Germany, the Braden scale has not yet been tested under scientific criteria. Such testing is needed before using the scale in different German settings. During the course of such testing, construction and study procedures of the American studies can be used as a basis as can the problems be identified in the analysis presented below.

[Approaches to medical training among physicians who teach; analysis of two different educational strategies].

PubMed

Loría-Castellanos, Jorge; Rivera-lbarra, Doris Beatriz; Márquez-Avila, Guadalupe

2009-01-01

Compare the outreach of a promotional educational strategy that focuses on active participation and compare it with a more traditional approach to medical training. A quasi-experimental design was approved by the research committee. We compared the outreach of two different approaches to medical training. We administered a validated instrument that included 72 items that analyze statements used to measure educational tasks in the form of duplets through 3 indicators. A group that included seven physicians that were actively participating in teaching activities was stratified according to teaching approaches. One of the approaches was a traditional one and the other included a promotional strategy aimed at increasing participation. All participants signed informed consent before answering the research instruments. Statistical analysis was done using non-parametric tests. Mann-Whitney results did not show differences among the group in the preliminary analysis. A second analysis with the same test after the interventions found significant differences (p d" 0.018) in favor of those subjects that had participated in the promotional approach mainly in the indicator measuring "consequence". The Wilcoxon test showed that all participants in the promotional approach increased significantly (pd" 0.018) in 3 main indicators as compared with the control group. A promotional strategy aimed at increasing physician participation constitutes a more profitable approach when compared with traditional teaching methods.

Alzheimer disease and cancer risk: a meta-analysis.

PubMed

Shi, Hai-bin; Tang, Bo; Liu, Yao-Wen; Wang, Xue-Feng; Chen, Guo-Jun

2015-03-01

Alzheimer disease (AD) and cancer are seemingly two opposite ends of one spectrum. Studies have suggested that patients with AD showed a reduced risk of cancer and vice versa. However, available evidences are not conclusive. So we conducted a meta-analysis using published literatures to systematically examine cancer risk in AD patients. A PubMed, EMBASE, and Web of Science search were conducted in May 2014. Pooled risk ratios (RRs) with their corresponding 95 % confidence intervals (CIs) were obtained using random-effects meta-analysis. We tested for publication bias and heterogeneity, and stratified for study characteristics, smoking-related cancers versus nonsmoking-related cancers, and site-specific cancers. Nine studies were included in this meta-analysis. Compared with controls, the pooled RR of cancer in AD patients was 0.55 (95 % CI 0.41-0.75), with significant heterogeneity among these studies (P < 0.001, I(2) = 83.5 %). The reduced cancer risk was more substantial when we restricted analyses to cohort studies, studies with adjusted estimates, studies defining AD by generally accepted criteria, and studies with longer length of follow-up. In sub-analyses for site-specific cancers, only lung cancer showed significant decreased risk (RR 0.72; 95 % CI 0.56-0.91). We did not find significant publication bias (P = 0.251 for Begg and Mazumdar's test and P = 0.143 for Egger's regression asymmetry test). These results support an association between AD and decreased cancer risk.

An Optimal Bahadur-Efficient Method in Detection of Sparse Signals with Applications to Pathway Analysis in Sequencing Association Studies.

PubMed

Dai, Hongying; Wu, Guodong; Wu, Michael; Zhi, Degui

2016-01-01

Next-generation sequencing data pose a severe curse of dimensionality, complicating traditional "single marker-single trait" analysis. We propose a two-stage combined p-value method for pathway analysis. The first stage is at the gene level, where we integrate effects within a gene using the Sequence Kernel Association Test (SKAT). The second stage is at the pathway level, where we perform a correlated Lancaster procedure to detect joint effects from multiple genes within a pathway. We show that the Lancaster procedure is optimal in Bahadur efficiency among all combined p-value methods. The Bahadur efficiency,[Formula: see text], compares sample sizes among different statistical tests when signals become sparse in sequencing data, i.e. ε →0. The optimal Bahadur efficiency ensures that the Lancaster procedure asymptotically requires a minimal sample size to detect sparse signals ([Formula: see text]). The Lancaster procedure can also be applied to meta-analysis. Extensive empirical assessments of exome sequencing data show that the proposed method outperforms Gene Set Enrichment Analysis (GSEA). We applied the competitive Lancaster procedure to meta-analysis data generated by the Global Lipids Genetics Consortium to identify pathways significantly associated with high-density lipoprotein cholesterol, low-density lipoprotein cholesterol, triglycerides, and total cholesterol.

The Statistical Value of Raw Fluorescence Signal in Luminex xMAP Based Multiplex Immunoassays

PubMed Central

Breen, Edmond J.; Tan, Woei; Khan, Alamgir

2016-01-01

Tissue samples (plasma, saliva, serum or urine) from 169 patients classified as either normal or having one of seven possible diseases are analysed across three 96-well plates for the presences of 37 analytes using cytokine inflammation multiplexed immunoassay panels. Censoring for concentration data caused problems for analysis of the low abundant analytes. Using fluorescence analysis over concentration based analysis allowed analysis of these low abundant analytes. Mixed-effects analysis on the resulting fluorescence and concentration responses reveals a combination of censoring and mapping the fluorescence responses to concentration values, through a 5PL curve, changed observed analyte concentrations. Simulation verifies this, by showing a dependence on the mean florescence response and its distribution on the observed analyte concentration levels. Differences from normality, in the fluorescence responses, can lead to differences in concentration estimates and unreliable probabilities for treatment effects. It is seen that when fluorescence responses are normally distributed, probabilities of treatment effects for fluorescence based t-tests has greater statistical power than the same probabilities from concentration based t-tests. We add evidence that the fluorescence response, unlike concentration values, doesn’t require censoring and we show with respect to differential analysis on the fluorescence responses that background correction is not required. PMID:27243383

Thermal and Mechanical Testing of Neoprene Gloves Used in a Space Shuttle Microgravity Glove Box Experiment

NASA Technical Reports Server (NTRS)

Wingard, Charles Doug; Munafo, Paul M. (Technical Monitor)

2001-01-01

Neoprene gloves are used in a Space Shuttle Microgravity Glove Box (MGBX) experiment. In 1999, significant corrosion was observed in the work area and on the outer surface of the left glove ring. Analysis of the corrosion products showed that they contained chlorine. The Neoprene gloves used in this glove box were obtained in 1995, with a recommended shelf life of 3 years. After storage of these gloves in a cabinet drawer until 1999, significant signs of corrosion were also observed in the drawer. Mechanical and thermal properties were determined on samples cut from the finger and sleeve areas of the "good" and "bad" gloves. This data showed significant aging of the left-hand glove, particularly in the sleeve area. Thermal analysis data by DSC and TGA was complimentary to tensile data in showing this aging. However, this test data did not pinpoint the cause of the left-hand glove aging, or of the corrosion products.

Taro corms mucilage/HPMC based transdermal patch: an efficient device for delivery of diltiazem hydrochloride.

PubMed

Sarkar, Gunjan; Saha, Nayan Ranjan; Roy, Indranil; Bhattacharyya, Amartya; Bose, Madhura; Mishra, Roshnara; Rana, Dipak; Bhattacharjee, Debashis; Chattopadhyay, Dipankar

2014-05-01

The aim of this work is to examine the effectiveness of mucilage/hydroxypropylmethylcellulose (HPMC) based transdermal patch (matrix type) as a drug delivery device. We have successfully extracted mucilage from Colocasia esculenta (Taro) corms and prepared diltiazem hydrochloride incorporated mucilage/HPMC based transdermal patches using various wt% of mucilage by the solvent evaporation technique. Characterization of both mucilage and transdermal patches has been done by several techniques such as Molisch's test, organoleptic evaluation of mucilage, mechanical, morphological and thermal analysis of transdermal patches. Skin irritation test is studied on hairless Albino rat skin showing that transdermal patches are apparently free of potentially hazardous skin irritation. Fourier transform infrared analysis shows that there is no interaction between drug, mucilage and HPMC while scanning electron microscopy shows the surface morphology of transdermal patches. In vitro drug release time of mucilage-HPMC based transdermal patches is prolonged with increasing mucilage concentration in the formulation. Copyright © 2014 Elsevier B.V. All rights reserved.

An improved method of crafting a multi-electrode spiral cuff for the selective.

PubMed

Rozman, Janez; Pečlin, Polona; Ribarič, Samo; Godec, Matjaž; Burja, Jaka

2018-01-17

This article reviews an improved methodology and technology for crafting a multi-electrode spiral cuff for the selective activation of nerve fibres in particular superficial regions of a peripheral nerve. The analysis, structural and mechanical properties of the spot welds used for the interconnections between the stimulating electrodes and stainless-steel lead wires are presented. The cuff consisted of 33 platinum electrodes embedded within a self-curling 17-mm-long silicone spiral sheet with a nominal internal diameter of 2.5 mm. The weld was analyzed using scanning electron microscopy and nanohardness tests, while the interconnection was investigated using destructive load tests. The functionality of the cuff was tested in an isolated porcine vagus nerve. The results of the scanning electron microscopy show good alloying and none of the typical welding defects that occur between the wire and the platinum foil. The results of the destructive load tests show that the breaking loads were between 3.22 and 5 N. The results of the nanohardness testing show that the hardness of the weld was different for the particular sites on the weld sample. Finally, the results of the functional testing show that for different stimulation intensities both the compound action potential deflection and the shape are modulated.

Isokinetic Extension Strength Is Associated With Single-Leg Vertical Jump Height.

PubMed

Fischer, Felix; Blank, Cornelia; Dünnwald, Tobias; Gföller, Peter; Herbst, Elmar; Hoser, Christian; Fink, Christian

2017-11-01

Isokinetic strength testing is an important tool in the evaluation of the physical capacities of athletes as well as for decision making regarding return to sports after anterior cruciate ligament (ACL) reconstruction in both athletes and the lay population. However, isokinetic testing is time consuming and requires special testing equipment. A single-jump test, regardless of leg dominance, may provide information regarding knee extension strength through the use of correlation analysis of jump height and peak torque of isokinetic muscle strength. Cross-sectional study; Level of evidence, 3. A total of 169 patients who underwent ACL reconstruction were included in this study. Isokinetic testing was performed on the injured and noninjured legs. Additionally, a single-leg countermovement jump was performed to assess jump height using a jump accelerometer sensor. Extension strength values were used to assess the association between isokinetic muscle strength and jump height. The sample consisted of 60 female (mean age, 20.8 ± 8.3 years; mean weight, 61.7 ± 6.5 kg; mean height, 167.7 ± 5.3 cm) and 109 male (mean age, 23.2 ± 7.7 years; mean weight, 74.6 ± 10.2 kg; mean height, 179.9 ± 6.9 cm) patients. Bivariate correlation analysis showed an association ( r = 0.56, P < .001) between jump height and isokinetic extension strength on the noninvolved side as well as an association ( r = 0.52, P < .001) for the involved side. Regression analysis showed that in addition to jump height (beta = 0.49, P < .001), sex (beta = -0.17, P = .008) and body mass index (beta = 0.37, P < .001) affected isokinetic strength. The final model explained 51.1% of the variance in isokinetic muscle strength, with jump height having the strongest impact (beta = 0.49, P < .001) and explaining 31.5% of the variance. Initial analysis showed a strong association between isokinetic strength and jump height. The study population encompassed various backgrounds, skill levels, and activity profiles, which might have affected the outcome. Even after controlling for age and sex, isokinetic strength was still moderately associated with jump height. Therefore, the jump technique and type of sport should be considered in future research.

Pathway modeling of microarray data: A case study of pathway activity changes in the testis following in utero exposure to dibutyl phthalate (DBP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ovacik, Meric A.; Sen, Banalata; Euling, Susan Y.

Pathway activity level analysis, the approach pursued in this study, focuses on all genes that are known to be members of metabolic and signaling pathways as defined by the KEGG database. The pathway activity level analysis entails singular value decomposition (SVD) of the expression data of the genes constituting a given pathway. We explore an extension of the pathway activity methodology for application to time-course microarray data. We show that pathway analysis enhances our ability to detect biologically relevant changes in pathway activity using synthetic data. As a case study, we apply the pathway activity level formulation coupled with significancemore » analysis to microarray data from two different rat testes exposed in utero to Dibutyl Phthalate (DBP). In utero DBP exposure in the rat results in developmental toxicity of a number of male reproductive organs, including the testes. One well-characterized mode of action for DBP and the male reproductive developmental effects is the repression of expression of genes involved in cholesterol transport, steroid biosynthesis and testosterone synthesis that lead to a decreased fetal testicular testosterone. Previous analyses of DBP testes microarray data focused on either individual gene expression changes or changes in the expression of specific genes that are hypothesized, or known, to be important in testicular development and testosterone synthesis. However, a pathway analysis may inform whether there are additional affected pathways that could inform additional modes of action linked to DBP developmental toxicity. We show that Pathway activity analysis may be considered for a more comprehensive analysis of microarray data.« less

GSA-PCA: gene set generation by principal component analysis of the Laplacian matrix of a metabolic network

PubMed Central

2012-01-01

Background Gene Set Analysis (GSA) has proven to be a useful approach to microarray analysis. However, most of the method development for GSA has focused on the statistical tests to be used rather than on the generation of sets that will be tested. Existing methods of set generation are often overly simplistic. The creation of sets from individual pathways (in isolation) is a poor reflection of the complexity of the underlying metabolic network. We have developed a novel approach to set generation via the use of Principal Component Analysis of the Laplacian matrix of a metabolic network. We have analysed a relatively simple data set to show the difference in results between our method and the current state-of-the-art pathway-based sets. Results The sets generated with this method are semi-exhaustive and capture much of the topological complexity of the metabolic network. The semi-exhaustive nature of this method has also allowed us to design a hypergeometric enrichment test to determine which genes are likely responsible for set significance. We show that our method finds significant aspects of biology that would be missed (i.e. false negatives) and addresses the false positive rates found with the use of simple pathway-based sets. Conclusions The set generation step for GSA is often neglected but is a crucial part of the analysis as it defines the full context for the analysis. As such, set generation methods should be robust and yield as complete a representation of the extant biological knowledge as possible. The method reported here achieves this goal and is demonstrably superior to previous set analysis methods. PMID:22876834

Evaluation of microtensile and tensile bond strength tests determining effects of erbium, chromium: yttrium-scandium-gallium-garnet laser pulse frequency on resin-enamel bonding.

PubMed

Yildirim, T; Ayar, M K; Yesilyurt, C; Kilic, S

2016-01-01

The aim of the present study was to compare two different bond strength test methods (tensile and microtensile) in investing the influence of erbium, chromium: yttrium-scandium-gallium-garnet (Er, Cr: YSGG) laser pulse frequency on resin-enamel bonding. One-hundred and twenty-five bovine incisors were used in the present study. Two test methods were used: Tensile bond strength (TBS; n = 20) and micro-TBS (μTBS; n = 5). Those two groups were further split into three subgroups according to Er, Cr: YSGG laser frequency (20, 35, and 50 Hz). Following adhesive procedures, microhybrid composite was placed in a custom-made bonding jig for TBS testing and incrementally for μTBS testing. TBS and μTBS tests were carried out using a universal testing machine and a microtensile tester, respectively. Analysis of TBS results showed that means were not significantly different. For μTBS, the Laser-50 Hz group showed the highest bond strength (P < 0.05), and increasing frequency significantly increased bond strength (P < 0.05). Comparing the two tests, the μTBS results showed higher means and lower standard deviations. It was demonstrated that increasing μTBS pulse frequency significantly improved immediate bond strength while TBS showed no significant effect. It can, therefore, be concluded that test method may play a significant role in determining optimum laser parameters for resin bonding.

Psychometric analysis of the Brisbane Practice Environment Measure (B-PEM).

PubMed

Flint, Anndrea; Farrugia, Charles; Courtney, Mary; Webster, Joan

2010-03-01

To undertake rigorous psychometric testing of the newly developed contemporary work environment measure (the Brisbane Practice Environment Measure [B-PEM]) using exploratory factor analysis and confirmatory factor analysis. Content validity of the 33-item measure was established by a panel of experts. Initial testing involved 195 nursing staff using principal component factor analysis with varimax rotation (orthogonal) and Cronbach's alpha coefficients. Confirmatory factor analysis was conducted using data from a further 983 nursing staff. Principal component factor analysis yielded a four-factor solution with eigenvalues greater than 1 that explained 52.53% of the variance. These factors were then verified using confirmatory factor analysis. Goodness-of-fit indices showed an acceptable fit overall with the full model, explaining 21% to 73% of the variance. Deletion of items took place throughout the evolution of the instrument, resulting in a 26-item, four-factor measure called the Brisbane Practice Environment Measure-Tested. The B-PEM has undergone rigorous psychometric testing, providing evidence of internal consistency and goodness-of-fit indices within acceptable ranges. The measure can be utilised as a subscale or total score reflective of a contemporary nursing work environment. An up-to-date instrument to measure practice environment may be useful for nursing leaders to monitor the workplace and to assist in identifying areas for improvement, facilitating greater job satisfaction and retention.

Buckling of a Longitudinally Jointed Curved Composite Panel Arc Segment for Next Generation of Composite Heavy Lift Launch Vehicles: Verification Testing Analysis

NASA Technical Reports Server (NTRS)

Farrokh, Babak; Segal, Kenneth N.; Akkerman, Michael; Glenn, Ronald L.; Rodini, Benjamin T.; Fan, Wei-Ming; Kellas, Sortiris; Pineda, Evan J.

2014-01-01

In this work, an all-bonded out-of-autoclave (OoA) curved longitudinal composite joint concept, intended for use in the next generation of composite heavy lift launch vehicles, was evaluated and verified through finite element (FE) analysis, fabrication, testing, and post-test inspection. The joint was used to connect two curved, segmented, honeycomb sandwich panels representative of a Space Launch System (SLS) fairing design. The overall size of the resultant panel was 1.37 m by 0.74 m (54 in by 29 in), of which the joint comprised a 10.2 cm (4 in) wide longitudinal strip at the center. NASTRAN and ABAQUS were used to perform linear and non-linear analyses of the buckling and strength performance of the jointed panel. Geometric non-uniformities (i.e., surface contour imperfections) were measured and incorporated into the FE model and analysis. In addition, a sensitivity study of the specimens end condition showed that bonding face-sheet doublers to the panel's end, coupled with some stress relief features at corner-edges, can significantly reduce the stress concentrations near the load application points. Ultimately, the jointed panel was subjected to a compressive load. Load application was interrupted at the onset of buckling (at 356 kN 80 kips). A post-test non-destructive evaluation (NDE) showed that, as designed, buckling occurred without introducing any damage into the panel or the joint. The jointed panel was further capable of tolerating an impact damage to the same buckling load with no evidence of damage propagation. The OoA cured all-composite joint shows promise as a low mass factory joint for segmented barrels.

Multi-parameter Observations and Validation of Pre-earthquake Atmospheric Signals

NASA Astrophysics Data System (ADS)

Ouzounov, D.; Pulinets, S. A.; Hattori, K.; Mogi, T.; Kafatos, M.

2014-12-01

We are presenting the latest development in multi-sensors observations of short-term pre-earthquake phenomena preceding major earthquakes. We are exploring the potential of pre-seismic atmospheric and ionospheric signals to alert for large earthquakes. To achieve this, we start validating anomalous ionospheric /atmospheric signals in retrospective and prospective modes. The integrated satellite and terrestrial framework (ISTF) is our method for validation and is based on a joint analysis of several physical and environmental parameters (Satellite thermal infrared radiation (OLR), electron concentration in the ionosphere (GPS/TEC), VHF-bands radio waves, radon/ion activities, air temperature and seismicity patterns) that were found to be associated with earthquakes. The science rationale for multidisciplinary analysis is based on concept Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) [Pulinets and Ouzounov, 2011], which explains the synergy of different geospace processes and anomalous variations, usually named short-term pre-earthquake anomalies. Our validation processes consist in two steps: (1) A continuous retrospective analysis preformed over two different regions with high seismicity- Taiwan and Japan for 2003-2009 The retrospective tests (100+ major earthquakes, M>5.9, Taiwan and Japan) show OLR anomalous behavior before all of these events with no false negatives. False alarm ratio for false positives is less then 25%. (2) Prospective testing using multiple parameters with potential for M5.5+ events. The initial testing shows systematic appearance of atmospheric anomalies in advance (days) to the M5.5+ events for Taiwan and Japan (Honshu and Hokkaido areas). Our initial prospective results suggest that our approach show a systematic appearance of atmospheric anomalies, one to several days prior to the largest earthquakes That feature could be further studied and tested for advancing the multi-sensors detection of pre-earthquake atmospheric signals.

Supersonic dynamic stability characteristics of the test technique demonstrator NASP configuration

NASA Technical Reports Server (NTRS)

Dress, David A.; Boyden, Richmond P.; Cruz, Christopher I.

1992-01-01

Wind tunnel tests of a National Aero-Space Plane (NASP) configuration were conducted in both test sections of the Langley Unitary Plan Wind Tunnel. The model used is a Langley designed blended body NASP configuration. Dynamic stability characteristics were measured on this configuration at Mach numbers of 2.0, 2.5, 3.5, and 4.5. In addition to tests of the baseline configuration, component buildup tests were conducted. The test results show that the baseline configuration generally has positive damping about all three axes with only isolated exceptions. In addition, there was generally good agreement between the in-pulse dynamic parameters and the corresponding static data which were measured during another series of tests in the Unitary Plan Wind Tunnel. Also included are comparisons of the experimental damping parameters with results from the engineering predictive code APAS (Aerodynamic Preliminary Analysis System). These comparisons show good agreement at low angles of attack; however, the comparisons are generally not as good at the higher angles of attack.

Accuracy of simple urine tests for diagnosis of urinary tract infections in low-risk pregnant women.

PubMed

Feitosa, Danielle Cristina Alves; da Silva, Márcia Guimarães; de Lima Parada, Cristina Maria Garcia

2009-01-01

Anatomic and physiological alterations during pregnancy predispose pregnant women to urinary tract infections (UTI). This study aimed to identify the accuracy of the simple urine test for UTI diagnosis in low-risk pregnant women. Diagnostic test performance was conducted in Botucatu, SP, involving 230 pregnant women, between 2006 and 2008. Results showed 10% UTI prevalence. Sensitivity, specificity and accuracy of the simple urine test were 95.6%, 63.3% and 66.5%, respectively, in relation to UTI diagnoses. The analysis of positive (PPV) and negative (NPV) predictive values showed that, when a regular simple urine test was performed, the chance of UTI occurrence was small (NPV 99.2%). In view of an altered result for such a test, the possibility of UTI existence was small (PPV 22.4%). It was concluded that the accuracy of the simple urine test as a diagnostic means for UTI was low, and that performing a urine culture is essential for appropriate diagnosis.

A multi-dimensional environment-health risk analysis system for the English regions

NASA Astrophysics Data System (ADS)

Vitolo, Claudia; Scutari, Marco; Ghalaieny, Mohamed; Tucker, Allan; Russell, Andrew

2017-04-01

There is an overwhelming body of evidence that environmental pollution, and air pollution in particular, is a significant threat to health worldwide. While in developed countries the introduction of environmental legislation and sustainable technologies aims to mitigate adverse effects, developing countries are at higher risk. Within the scope of the British Council funded KEHRA project, work is on-going to develop a reproducible and reliable system to assess health risks due to exposure to pollution under climate change and across countries. Our approach is based on the use of Bayesian Networks. We used these graphical models to explore and model the statistical dependence structure of the intricate environment-health nexus. We developed a robust modelling workflow in the R programming language to facilitate reproducibility and tested it on the English regions in the United Kingdom. Preliminary results are encouraging, showing that the model tests generally well in sample (training data spans the period 1981-2005) and has good predictive power when tested out of sample (testing data spans the period 2006-2014). We plan to show the results of this preliminary analysis as well as test the model under future climate change scenarios. Future work will also investigate the transferability of the model from a data-rich (England) to a data-poor environment (Kazakhstan).

Prediction of in-depth gap heating ratios from wing glove model test data. [space shuttle orbiter

NASA Technical Reports Server (NTRS)

1977-01-01

In-depth gap heating ratios were predicted down RSI tile sidewalls based on temperature measurements obtained from the JSC arc-jet Wing Glove model tests in order to develop gap heating ratios which resulted in the best possible fit of test data and to produce a set of engineering verification heating ratios similar in shape to one another which could be used at various body points on the Orbiter during reentry. The Rockwell TPS Multidimensional heat conduction program was used to perform 3-D thermal analyses using a 3.0 in. thick section of a curved RSI tile with 283 nodal points. Correlation with test data shows that the predicted heating ratios were significantly higher down in the gap than the zero pressure values for T/C stacks 39 and 38 on the Wing Glove model. For stack 37 (in a low pressure region), the baseline heating ratio overpredicted the temperature data. This analysis, which showed that the heating ratios were a strong function of the product of pressure and pressure gradient, will be used to compare with recent Gap/Step and Ames Double Wedge test/analysis results in the effort to identify the Orbiter gap response to high delta P flight environment.

Upregulation of MAOA in the hippocampus results in delayed depressive-like behaviors in burn mice.

PubMed

Wang, Zhen; Chen, Lu; Rong, Xinzhou; Wang, Xuemin

2017-04-14

To observe depressive-like behavior and hippocampus monoamine oxidase A (MAOA) changes in burned mice. We tested depression and anxiety like behaviors of burn C57 mice with the sucrose preference test, forced swimming test (FST), open field test and elevated plus maze test and then detected the MAOA content and MAOA gene transcriptional levels in the hippocampus with western blot analysis and real-time quantitative PCR analysis. We then sought to reverse depressive-like behavior of burned mice with an MAOA inhibitor. (1) Mice showed depressive and anxiety like behaviors one week after they were burned; (2) The content of MAOA in the hippocampus of burned mice was significantly higher than that in control mice (P<0.05); (3) MAOA gene transcription in the hippocampus of burned mice was significantly increased (MAOA mRNA was increased, P<0.05); (4) treatment with a MAOA inhibitor (phenelzine) significantly increased the sucrose preference rate and decreased FST immobility time in burned mice, and also decreased elevated expression of MAOA in the hippocampus of burned mice. Burned mice showed "delayed" depressive-like behavior combined with a degree of anxiety; this phenomenon is likely associated with the increase in MAOA expression in the hippocampus. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Real-time polymerase chain reaction detection of parvovirus B19 DNA in blood donations using a commercial and an in-house assay.

PubMed

Koppelman, M H G M; van Swieten, P; Cuijpers, H T M

2011-06-01

European regulations require testing of manufacturing plasma for parvovirus B19 (B19) DNA to limit the load of this virus to a maximum acceptable level of 10 IU/µL. To meet this requirement, most manufacturers introduced a test algorithm to identify and eliminate high-load donations before making large manufacturing pools of plasma units. Sanquin screens all donations using a commercial assay from Roche and an in-house assay. Between 2006 and 2009, 6.2 million donations were screened using two different polymerase chain reaction (PCR) assays targeting B19 DNA. Donations with B19 DNA loads of greater than 1 × 10(6) IU/mL showing significant differences in viral load between the two assays were further analyzed by sequencing analysis. A total of 396 donations with B19 DNA loads of greater than 1 × 10(6) IU/mL were identified. Fifteen samples (3.8%) had discordant test results; 10 samples (2.5%) were underquantified by the Roche assay, two samples (0.5%) were underquantified by the in-house assay, and three samples (0.8%) were not detected by the Roche assay. Sequencing analysis revealed mismatches in primer and probe-binding regions. Phylogenetic analysis showed that 12 samples were B19 Genotype 1. The three samples not detected by the Roche assay were B19 Genotype 2. This study shows that 3.8% of the viremic B19 DNA-positive donations are not quantified correctly by the Roche or in-house B19 DNA assays. B19 Genotype 1 isolates showing incorrect test results are more common than B19 Genotype 2 or 3 isolates. Newly designed B19 PCR assays for blood screening should preferably have multiplexed formats targeting multiple regions of the B19 genome. © 2010 American Association of Blood Banks.

Cost effectiveness of population based BRCA1 founder mutation testing in Sephardi Jewish women.

PubMed

Patel, Shreeya; Legood, Rosa; Evans, D Gareth; Turnbull, Clare; Antoniou, Antonis C; Menon, Usha; Jacobs, Ian; Manchanda, Ranjit

2018-04-01

Population-based BRCA1/BRCA2 founder-mutation testing has been demonstrated as cost effective compared with family history based testing in Ashkenazi Jewish women. However, only 1 of the 3 Ashkenazi Jewish BRCA1/BRCA2 founder mutations (185delAG[c.68_69delAG]), 5382insC[c.5266dupC]), and 6174delT[c.5946delT]) is found in the Sephardi Jewish population (185delAG[c.68_69delAG]), and the overall prevalence of BRCA mutations in the Sephardi Jewish population is accordingly lower (0.7% compared with 2.5% in the Ashkenazi Jewish population). Cost-effectiveness analyses of BRCA testing have not previously been performed at these lower BRCA prevalence levels seen in the Sephardi Jewish population. Here we present a cost-effectiveness analysis for UK and US populations comparing population testing with clinical criteria/family history-based testing in Sephardi Jewish women. A Markov model was built comparing the lifetime costs and effects of population-based BRCA1 testing, with testing using family history-based clinical criteria in Sephardi Jewish women aged ≥30 years. BRCA1 carriers identified were offered magnetic resonance imaging/mammograms and risk-reducing surgery. Costs are reported at 2015 prices. Outcomes include breast cancer, ovarian cancer, and excess deaths from heart disease. All costs and outcomes are discounted at 3.5%. The time horizon is lifetime, and perspective is payer. The incremental cost-effectiveness ratio per quality-adjusted life-year was calculated. Parameter uncertainty was evaluated through 1-way and probabilistic sensitivity analysis. Population testing resulted in gain in life expectancy of 12 months (quality-adjusted life-year = 1.00). The baseline discounted incremental cost-effectiveness ratio for UK population-based testing was £67.04/quality-adjusted life-year and for US population was $308.42/quality-adjusted life-year. Results were robust in the 1-way sensitivity analysis. The probabilistic sensitivity analysis showed 100% of simulations were cost effective at £20,000/quality-adjusted life-year UK and the $100,000/quality-adjusted life-year US willingness-to-pay thresholds. Scenario analysis showed that population testing remains cost effective in UK and US populations, even if premenopausal oophorectomy does not reduce breast cancer risk or if hormone replacement therapy compliance is nil. Population-based BRCA1 testing is highly cost effective compared with clinical criteria-driven approach in Sephardi Jewish women. This supports changing the paradigm to population-based BRCA testing in the Jewish population, regardless of Ashkenazi/Sephardi ancestry. Copyright © 2017 Elsevier Inc. All rights reserved.

Test-retest reliability of computer-based video analysis of general movements in healthy term-born infants.

PubMed

Valle, Susanne Collier; Støen, Ragnhild; Sæther, Rannei; Jensenius, Alexander Refsum; Adde, Lars

2015-10-01

A computer-based video analysis has recently been presented for quantitative assessment of general movements (GMs). This method's test-retest reliability, however, has not yet been evaluated. The aim of the current study was to evaluate the test-retest reliability of computer-based video analysis of GMs, and to explore the association between computer-based video analysis and the temporal organization of fidgety movements (FMs). Test-retest reliability study. 75 healthy, term-born infants were recorded twice the same day during the FMs period using a standardized video set-up. The computer-based movement variables "quantity of motion mean" (Qmean), "quantity of motion standard deviation" (QSD) and "centroid of motion standard deviation" (CSD) were analyzed, reflecting the amount of motion and the variability of the spatial center of motion of the infant, respectively. In addition, the association between the variable CSD and the temporal organization of FMs was explored. Intraclass correlation coefficients (ICC 1.1 and ICC 3.1) were calculated to assess test-retest reliability. The ICC values for the variables CSD, Qmean and QSD were 0.80, 0.80 and 0.86 for ICC (1.1), respectively; and 0.80, 0.86 and 0.90 for ICC (3.1), respectively. There were significantly lower CSD values in the recordings with continual FMs compared to the recordings with intermittent FMs (p<0.05). This study showed high test-retest reliability of computer-based video analysis of GMs, and a significant association between our computer-based video analysis and the temporal organization of FMs. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Sensitivity and specificity of the Streptococcus pneumoniae urinary antigen test for unconcentrated urine from adult patients with pneumonia: a meta-analysis.

PubMed

Horita, Nobuyuki; Miyazawa, Naoki; Kojima, Ryota; Kimura, Naoko; Inoue, Miyo; Ishigatsubo, Yoshiaki; Kaneko, Takeshi

2013-11-01

Studies on the sensitivity and specificity of the Binax Now Streptococcus pneumonia urinary antigen test (index test) show considerable variance of results. Those written in English provided sufficient original data to evaluate the sensitivity and specificity of the index test using unconcentrated urine to identify S. pneumoniae infection in adults with pneumonia. Reference tests were conducted with at least one culture and/or smear. We estimated sensitivity and two specificities. One was the specificity evaluated using only patients with pneumonia of identified other aetiologies ('specificity (other)'). The other was the specificity evaluated based on both patients with pneumonia of unknown aetiology and those with pneumonia of other aetiologies ('specificity (unknown and other)') using a fixed model for meta-analysis. We found 10 articles involving 2315 patients. The analysis of 10 studies involving 399 patients yielded a pooled sensitivity of 0.75 (95% confidence interval: 0.71-0.79) without heterogeneity or publication bias. The analysis of six studies involving 258 patients yielded a pooled specificity (other) of 0.95 (95% confidence interval: 0.92-0.98) without no heterogeneity or publication bias. We attempted to conduct a meta-analysis with the 10 studies involving 1916 patients to estimate specificity (unknown and other), but it remained unclear due to moderate heterogeneity and possible publication bias. In our meta-analysis, sensitivity of the index test was moderate and specificity (other) was high; however, the specificity (unknown and other) remained unclear. © 2013 The Authors. Respirology © 2013 Asian Pacific Society of Respirology.

Annotation analysis for testing drug safety signals using unstructured clinical notes

PubMed Central

2012-01-01

Background The electronic surveillance for adverse drug events is largely based upon the analysis of coded data from reporting systems. Yet, the vast majority of electronic health data lies embedded within the free text of clinical notes and is not gathered into centralized repositories. With the increasing access to large volumes of electronic medical data—in particular the clinical notes—it may be possible to computationally encode and to test drug safety signals in an active manner. Results We describe the application of simple annotation tools on clinical text and the mining of the resulting annotations to compute the risk of getting a myocardial infarction for patients with rheumatoid arthritis that take Vioxx. Our analysis clearly reveals elevated risks for myocardial infarction in rheumatoid arthritis patients taking Vioxx (odds ratio 2.06) before 2005. Conclusions Our results show that it is possible to apply annotation analysis methods for testing hypotheses about drug safety using electronic medical records. PMID:22541596

Ranking metrics in gene set enrichment analysis: do they matter?

PubMed

Zyla, Joanna; Marczyk, Michal; Weiner, January; Polanska, Joanna

2017-05-12

There exist many methods for describing the complex relation between changes of gene expression in molecular pathways or gene ontologies under different experimental conditions. Among them, Gene Set Enrichment Analysis seems to be one of the most commonly used (over 10,000 citations). An important parameter, which could affect the final result, is the choice of a metric for the ranking of genes. Applying a default ranking metric may lead to poor results. In this work 28 benchmark data sets were used to evaluate the sensitivity and false positive rate of gene set analysis for 16 different ranking metrics including new proposals. Furthermore, the robustness of the chosen methods to sample size was tested. Using k-means clustering algorithm a group of four metrics with the highest performance in terms of overall sensitivity, overall false positive rate and computational load was established i.e. absolute value of Moderated Welch Test statistic, Minimum Significant Difference, absolute value of Signal-To-Noise ratio and Baumgartner-Weiss-Schindler test statistic. In case of false positive rate estimation, all selected ranking metrics were robust with respect to sample size. In case of sensitivity, the absolute value of Moderated Welch Test statistic and absolute value of Signal-To-Noise ratio gave stable results, while Baumgartner-Weiss-Schindler and Minimum Significant Difference showed better results for larger sample size. Finally, the Gene Set Enrichment Analysis method with all tested ranking metrics was parallelised and implemented in MATLAB, and is available at https://github.com/ZAEDPolSl/MrGSEA . Choosing a ranking metric in Gene Set Enrichment Analysis has critical impact on results of pathway enrichment analysis. The absolute value of Moderated Welch Test has the best overall sensitivity and Minimum Significant Difference has the best overall specificity of gene set analysis. When the number of non-normally distributed genes is high, using Baumgartner-Weiss-Schindler test statistic gives better outcomes. Also, it finds more enriched pathways than other tested metrics, which may induce new biological discoveries.

Finite-Element Vibration Analysis and Modal Testing of Graphite Epoxy Tubes and Correlation Between the Data

NASA Technical Reports Server (NTRS)

Taleghani, Barmac K.; Pappa, Richard S.

1996-01-01

Structural materials in the form of graphite epoxy composites with embedded rubber layers are being used to reduce vibrations in rocket motor tubes. Four filament-wound, graphite epoxy tubes were studied to evaluate the effects of the rubber layer on the modal parameters (natural vibration frequencies, damping, and mode shapes). Tube 1 contained six alternating layers of 30-degree helical wraps and 90-degree hoop wraps. Tube 2 was identical to tube 1 with the addition of an embedded 0.030-inch-thick rubber layer. Tubes 3 and 4 were identical to tubes 1 and 2, respectively, with the addition of a Textron Kelpoxy elastomer. This report compares experimental modal parameters obtained by impact testing with analytical modal parameters obtained by NASTRAN finite-element analysis. Four test modes of tube 1 and five test modes of tube 3 correlate highly with corresponding analytical predictions. Unsatisfactory correlation of test and analysis results occurred for tubes 2 and 4 and these comparisons are not shown. Work is underway to improve the analytical models of these tubes. Test results clearly show that the embedded rubber layers significantly increase structural modal damping as well as decrease natural vibration frequencies.

Defining, illustrating and reflecting on logic analysis with an example from a professional development program.

PubMed

Tremblay, Marie-Claude; Brousselle, Astrid; Richard, Lucie; Beaudet, Nicole

2013-10-01

Program designers and evaluators should make a point of testing the validity of a program's intervention theory before investing either in implementation or in any type of evaluation. In this context, logic analysis can be a particularly useful option, since it can be used to test the plausibility of a program's intervention theory using scientific knowledge. Professional development in public health is one field among several that would truly benefit from logic analysis, as it appears to be generally lacking in theorization and evaluation. This article presents the application of this analysis method to an innovative public health professional development program, the Health Promotion Laboratory. More specifically, this paper aims to (1) define the logic analysis approach and differentiate it from similar evaluative methods; (2) illustrate the application of this method by a concrete example (logic analysis of a professional development program); and (3) reflect on the requirements of each phase of logic analysis, as well as on the advantages and disadvantages of such an evaluation method. Using logic analysis to evaluate the Health Promotion Laboratory showed that, generally speaking, the program's intervention theory appeared to have been well designed. By testing and critically discussing logic analysis, this article also contributes to further improving and clarifying the method. Copyright © 2013 Elsevier Ltd. All rights reserved.

Penetration analysis of projectile with inclined concrete target

NASA Astrophysics Data System (ADS)

Kim, S. B.; Kim, H. W.; Yoo, Y. H.

2015-09-01

This paper presents numerical analysis result of projectile penetration with concrete target. We applied dynamic material properties of 4340 steels, aluminium and explosive for projectile body. Dynamic material properties were measured with static tensile testing machine and Hopkinson pressure bar tests. Moreover, we used three concrete damage models included in LS-DYNA 3D, such as SOIL_CONCRETE, CSCM (cap model with smooth interaction) and CONCRETE_DAMAGE (K&C concrete) models. Strain rate effect for concrete material is important to predict the fracture deformation and shape of concrete, and penetration depth for projectiles. CONCRETE_DAMAGE model with strain rate effect also applied to penetration analysis. Analysis result with CSCM model shows good agreement with penetration experimental data. The projectile trace and fracture shapes of concrete target were compared with experimental data.

Research notes : listening to bridges.

DOT National Transportation Integrated Search

2008-09-01

The Federal Highway Administration requires owners of structurally deficient bridges to repair, replace, restrict truck loads, or conduct analysis and testing to maintain a safe highway system. Past experiments on reinforced concrete beams showed aco...

Comparison of data analysis strategies for intent-to-treat analysis in pre-test-post-test designs with substantial dropout rates.

PubMed

Salim, Agus; Mackinnon, Andrew; Christensen, Helen; Griffiths, Kathleen

2008-09-30

The pre-test-post-test design (PPD) is predominant in trials of psychotherapeutic treatments. Missing data due to withdrawals present an even bigger challenge in assessing treatment effectiveness under the PPD than under designs with more observations since dropout implies an absence of information about response to treatment. When confronted with missing data, often it is reasonable to assume that the mechanism underlying missingness is related to observed but not to unobserved outcomes (missing at random, MAR). Previous simulation and theoretical studies have shown that, under MAR, modern techniques such as maximum-likelihood (ML) based methods and multiple imputation (MI) can be used to produce unbiased estimates of treatment effects. In practice, however, ad hoc methods such as last observation carried forward (LOCF) imputation and complete-case (CC) analysis continue to be used. In order to better understand the behaviour of these methods in the PPD, we compare the performance of traditional approaches (LOCF, CC) and theoretically sound techniques (MI, ML), under various MAR mechanisms. We show that the LOCF method is seriously biased and conclude that its use should be abandoned. Complete-case analysis produces unbiased estimates only when the dropout mechanism does not depend on pre-test values even when dropout is related to fixed covariates including treatment group (covariate-dependent: CD). However, CC analysis is generally biased under MAR. The magnitude of the bias is largest when the correlation of post- and pre-test is relatively low.

[Interpretation of false positive results of biochemical prenatal tests].

PubMed

Sieroszewski, Piotr; Słowakiewicz, Katarzyna; Perenc, Małgorzata

2010-03-01

Modern, non-invasive prenatal diagnostics based on biochemical and ultrasonographic markers of fetal defects allows us to calculate the risk of fetal chromosomal aneuploidies with high sensitivity and specificity An introduction of biochemical, non-invasive prenatal tests turned out to result in frequent false positive results of these tests in cases when invasive diagnostics does not confirm fetal defects. However prospective analysis of these cases showed numerous complications in the third trimester of the pregnancies.

The Role of NREM Sleep Instability in Child Cognitive Performance

PubMed Central

Bruni, Oliviero; Kohler, Mark; Novelli, Luana; Kennedy, Declan; Lushington, Kurt; Martin, James; Ferri, Raffaele

2012-01-01

Study Objectives: Based on recent reports of the involvement of cyclic alternating pattern (CAP) in cognitive functioning in adults, we investigated the association between CAP parameters and cognitive performance in healthy children. Design: Polysomnographic assessment and standardized neurocognitive testing in healthy children. Settings: Sleep laboratory. Participants: Forty-two children aged 7.6 ± 2.7 years, with an even distribution of body mass percentile (58.5 ± 25.5) and SES reflective of national norms. Measurements: Analysis of sleep macrostructure following the R&K criteria and of cyclic alternating pattern (CAP). The neurocognitive tests were the Stanford Binet Intelligence Scale (5th edition) and a Neuropsychological Developmental Assessment (NEPSY) Results: Fluid reasoning ability was positively associated with CAP rate, particularly during SWS and with A1 total index and A1 index in SWS. Regression analysis, controlling for age and SES, showed that CAP rate in SWS and A1 index in SWS were significant predictors of nonverbal fluid reasoning, explaining 24% and 22% of the variance in test scores, respectively. Conclusion: This study shows that CAP analysis provides important insights on the role of EEG slow oscillations (CAP A1) in cognitive performance. Children with higher cognitive efficiency showed an increase of phase A1 in total sleep and in SWS Citation: Bruni O; Kohler M; Novelli L; Kennedy D; Lushington K; Martin J; Ferri R. The role of NREM sleep instability in child cognitive performance. SLEEP 2012;35(5):649-656. PMID:22547891

Diagnostic performance of urine dipstick testing in children with suspected UTI: a systematic review of relationship with age and comparison with microscopy.

PubMed

Mori, R; Yonemoto, N; Fitzgerald, A; Tullus, K; Verrier-Jones, K; Lakhanpaul, M

2010-04-01

Prompt diagnosis of urinary tract infection (UTI) in children is needed to initiate treatment but is difficult to establish without urine testing, and reliance on culture leads to delay. Urine dipsticks are often used as an alternative to microscopy, although the diagnostic performance of dipsticks at different ages has not been established systematically. Studies comparing urine dipstick testing in infants versus older children and urine dipstick versus microscopy were systematically searched and reviewed. Meta-analysis of available studies was conducted. Six studies addressed these questions. The results of meta-analysis showed that the performance of urine dipstick testing was significantly less in the younger children when compared with older children (p < 0.01). Positive likelihood ratio (LR) of both nitrite and leucocyte positive 38.54 [95% confidence interval (CI) 22.49-65.31], negative LR for both negative 0.13 (95% CI 0.07-0.25) are reasonably good, and those for young infants are less reliable [positive LR 7.62 (95% CI 0.95-51.85) and negative LR 0.34 (95% CI 0.66-0.15)]. Comparing microscopy and urine dipstick testing, using bacterial colony count on urine culture showed no significant difference between the two methods. Urine dipstick testing is more effective for diagnosis of UTI in children over 2 years than for younger children.

Modeling of Micro Deval abrasion loss based on some rock properties

NASA Astrophysics Data System (ADS)

Capik, Mehmet; Yilmaz, Ali Osman

2017-10-01

Aggregate is one of the most widely used construction material. The quality of the aggregate is determined using some testing methods. Among these methods, the Micro Deval Abrasion Loss (MDAL) test is commonly used for the determination of the quality and the abrasion resistance of aggregate. The main objective of this study is to develop models for the prediction of MDAL from rock properties, including uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness, apparent porosity, void ratio Cerchar abrasivity index and Bohme abrasion test are examined. Additionally, the MDAL is modeled using simple regression analysis and multiple linear regression analysis based on the rock properties. The study shows that the MDAL decreases with the increase of uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness and Cerchar abrasivity index. It is also concluded that the MDAL increases with the increase of apparent porosity, void ratio and Bohme abrasion test. The modeling results show that the models based on Bohme abrasion test and L type Schmidt rebound hardness give the better forecasting performances for the MDAL. More models, including the uniaxial compressive strength, the apparent porosity and Cerchar abrasivity index, are developed for the rapid estimation of the MDAL of the rocks. The developed models were verified by statistical tests. Additionally, it can be stated that the proposed models can be used as a forecasting for aggregate quality.

Visuo-Spatial Performance in Autism: A Meta-Analysis

ERIC Educational Resources Information Center

Muth, Anne; Hönekopp, Johannes; Falter, Christine M.

2014-01-01

Visuo-spatial skills are believed to be enhanced in autism spectrum disorders (ASDs). This meta-analysis tests the current state of evidence for Figure Disembedding, Block Design, Mental Rotation and Navon tasks in ASD and neurotypicals. Block Design (d = 0.32) and Figure Disembedding (d = 0.26) showed superior performance for ASD with large…

Full-field local displacement analysis of two-sided paperboard

Treesearch

J.M. Considine; D.W. Vahey

2007-01-01

This report describes a method to examine full-field displacements of both sides of paperboard during tensile testing. Analysis showed out-of-plane shear behavior near the failures zones. The method was reliably used to examine out-of-plane shear in double notch shear specimens. Differences in shear behavior of machine direction and cross-machine direction specimens...

Two-step rating-based 'double-faced applicability' test for sensory analysis of spread products as an alternative to descriptive analysis with trained panel.

PubMed

Kim, In-Ah; den-Hollander, Elyn; Lee, Hye-Seong

2018-03-01

Descriptive analysis with a trained sensory panel has thus far been the most well defined methodology to characterize various products. However, in practical terms, intensive training in descriptive analysis has been recognized as a serious defect. To overcome this limitation, various novel rapid sensory profiling methodologies have been suggested in the literature. Among these, attribute-based methodologies such as check-all-that-apply (CATA) questions showed results comparable to those of conventional sensory descriptive analysis. Kim, Hopkinson, van Hout, and Lee (2017a, 2017b) have proposed a novel attribute-based methodology termed the two-step rating-based 'double-faced applicability' test with a novel output measure of applicability magnitude (d' A ) for measuring consumers' product usage experience throughout various product usage stages. In this paper, the potential of the two-step rating-based 'double-faced applicability' test with d' A was investigated as an alternative to conventional sensory descriptive analysis in terms of sensory characterization and product discrimination. Twelve commercial spread products were evaluated using both conventional sensory descriptive analysis with a trained sensory panel and two-step rating-based 'double-faced applicability' test with an untrained sensory panel. The results demonstrated that the 'double-faced applicability' test can be used to provide a direct measure of the applicability magnitude of sensory attributes of the samples tested in terms of d' A for sensory characterization of individual samples and multiple sample comparisons. This suggests that when the appropriate list of attributes to be used in the questionnaire is already available, the two-step rating-based 'double-faced applicability' test with d' A can be used as a more efficient alternative to conventional descriptive analysis, without requiring any intensive training process. Copyright © 2017 Elsevier Ltd. All rights reserved.

Diagnostic methods for CW laser damage testing

NASA Astrophysics Data System (ADS)

Stewart, Alan F.; Shah, Rashmi S.

2004-06-01

High performance optical coatings are an enabling technology for many applications - navigation systems, telecom, fusion, advanced measurement systems of many types as well as directed energy weapons. The results of recent testing of superior optical coatings conducted at high flux levels will be presented. The diagnostics used in this type of nondestructive testing and the analysis of the data demonstrates the evolution of test methodology. Comparison of performance data under load to the predictions of thermal and optical models shows excellent agreement. These tests serve to anchor the models and validate the performance of the materials and coatings.

Evaluation of the LIA-ANA-Profile-17S for the detection of autoantibodies to nuclear antigens.

PubMed

Yi, Ahram; Lee, Chang-Hoon; Moon, Hee-Won; Kim, Hanah; Hur, Mina; Yun, Yeo-Min

2018-05-01

The diagnostic tests for autoimmune disease include screening for autoantibodies for nuclear antigens (ANA) and antibodies against extractable nuclear antigens (ENA). Using the line immunoassay (LIA) method, various kinds of ENA antibodies can be detected simultaneously. We evaluated the performance of the newly launched LIA-ANA-Profile-17S (Shenzhen YHLO Biotech, Shenzhen, China) as compared to a conventional LIA kit. Residual samples were collected from 200 patients who had been tested for ANA using indirect immunofluorescence. The LIA-ANA-Profile-17S was compared to the EuroLine ANA (Euroimmun, Oberlausitz, Germany) for the analysis of 17 different autoantibodies. The concordance rate and agreement between assays were determined. Samples showing discrepancies between the LIA-ANA-Profile-17S and EuroLine tests were further examined through additional analysis. The overall agreement was moderate (kappa = 0.759, 95% CI = 0.712-0.805). Agreement between assays ranged from weak to almost perfect, except for those tests targeting nucleosomes, histones, and PM-Scl. Of the 57 disparate results between LIA-ANA-Profile-17S and EuroLine, 38 (66.7%) samples tested positive under an additional assay, showing variable patterns between types of autoantibodies. The positive rate of each autoantibody between LIA-ANA-Profile-17S and EuroLine did not differ significantly, except for anti-nucleosome and anti-histone assays in samples from patients diagnosed with systemic lupus erythematosus (P = 0.004 and 0.001, respectively). Compared to those from the conventional EuroLine assay, the LIA-ANA-Profile-17S results showed variable agreement in samples showing different prevalence of each autoantibody. The most frequently detected antibodies showed almost perfect agreement. The LIA-ANA-Profile-17S could play a role in the diagnosis of systemic autoimmune disease in ANA-positive samples. Copyright © 2018 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Epistasis analysis for quantitative traits by functional regression model.

PubMed

Zhang, Futao; Boerwinkle, Eric; Xiong, Momiao

2014-06-01

The critical barrier in interaction analysis for rare variants is that most traditional statistical methods for testing interactions were originally designed for testing the interaction between common variants and are difficult to apply to rare variants because of their prohibitive computational time and poor ability. The great challenges for successful detection of interactions with next-generation sequencing (NGS) data are (1) lack of methods for interaction analysis with rare variants, (2) severe multiple testing, and (3) time-consuming computations. To meet these challenges, we shift the paradigm of interaction analysis between two loci to interaction analysis between two sets of loci or genomic regions and collectively test interactions between all possible pairs of SNPs within two genomic regions. In other words, we take a genome region as a basic unit of interaction analysis and use high-dimensional data reduction and functional data analysis techniques to develop a novel functional regression model to collectively test interactions between all possible pairs of single nucleotide polymorphisms (SNPs) within two genome regions. By intensive simulations, we demonstrate that the functional regression models for interaction analysis of the quantitative trait have the correct type 1 error rates and a much better ability to detect interactions than the current pairwise interaction analysis. The proposed method was applied to exome sequence data from the NHLBI's Exome Sequencing Project (ESP) and CHARGE-S study. We discovered 27 pairs of genes showing significant interactions after applying the Bonferroni correction (P-values < 4.58 × 10(-10)) in the ESP, and 11 were replicated in the CHARGE-S study. © 2014 Zhang et al.; Published by Cold Spring Harbor Laboratory Press.

Mixed-Effects Models for Count Data with Applications to Educational Research

ERIC Educational Resources Information Center

Shin, Jihyung

2012-01-01

This research is motivated by an analysis of reading research data. We are interested in modeling the test outcome of ability to fluently recode letters into sounds of kindergarten children aged between 5 and 7. The data showed excessive zero scores (more than 30% of children) on the test. In this dissertation, we carefully examine the models…

Removal of phosphorus using chemically modified lignocellulosic materials

Treesearch

James S. Han; N. Hur; B. Choi; Soo-Hong Min

2003-01-01

Heavy metals from an acid mine drainage (AMD) site were precipitated on the surface of juniper fiber. The modified fiber was tested in lab-scaled batch and column tests and in the field. Elemental analysis showed that soluble iron species deposited on the fiber act as an inorganic adsorbent for anions. Sorption capacity, determined by fitting results to a Langmuir...

Testing and School Improvement. PEPS Policy Paper Series Number 9.

ERIC Educational Resources Information Center

Cooley, William W.

The Test of Essential Learning and Literacy Skills (TELLS) has been administered to all Pennsylvania students in grades 3, 5, and 8 since 1985. An analysis of results from the 1,505 public elementary schools that served both third and fifth graders between 1986 and 1990 show that in 150 of these schools more than 50 percent of the students scored…

Relevant climate response tests for stratospheric aerosol injection: A combined ethical and scientific analysis

NASA Astrophysics Data System (ADS)

Lenferna, Georges Alexandre; Russotto, Rick D.; Tan, Amanda; Gardiner, Stephen M.; Ackerman, Thomas P.

2017-06-01

In this paper, we focus on stratospheric sulfate injection as a geoengineering scheme, and provide a combined scientific and ethical analysis of climate response tests, which are a subset of outdoor tests that would seek to impose detectable and attributable changes to climate variables on global or regional scales. We assess the current state of scientific understanding on the plausibility and scalability of climate response tests. Then, we delineate a minimal baseline against which to consider whether certain climate response tests would be relevant for a deployment scenario. Our analysis shows that some climate response tests, such as those attempting to detect changes in regional climate impacts, may not be deployable in time periods relevant to realistic geoengineering scenarios. This might pose significant challenges for justifying stratospheric sulfate aerosol injection deployment overall. We then survey some of the major ethical challenges that proposed climate response tests face. We consider what levels of confidence would be required to ethically justify approving a proposed test; whether the consequences of tests are subject to similar questions of justice, compensation, and informed consent as full-scale deployment; and whether questions of intent and hubris are morally relevant for climate response tests. We suggest further research into laboratory-based work and modeling may help to narrow the scientific uncertainties related to climate response tests, and help inform future ethical debate. However, even if such work is pursued, the ethical issues raised by proposed climate response tests are significant and manifold.

LED Curing Lights and Temperature Changes in Different Tooth Sites

PubMed Central

Armellin, E.; Bovesecchi, G.; Coppa, P.; Pasquantonio, G.; Cerroni, L.

2016-01-01

Objectives. The aim of this in vitro study was to assess thermal changes on tooth tissues during light exposure using two different LED curing units. The hypothesis was that no temperature increase could be detected within the dental pulp during polymerization irrespective of the use of a composite resin or a light-curing unit. Methods. Caries-free human first molars were selected, pulp residues were removed after root resection, and four calibrated type-J thermocouples were positioned. Two LED lamps were tested; temperature measurements were made on intact teeth and on the same tooth during curing of composite restorations. The data was analyzed by one-way analysis of variance (ANOVA), Wilcoxon test, Kruskal-Wallis test, and Pearson's χ 2. After ANOVA, the Bonferroni multiple comparison test was performed. Results. Polymerization data analysis showed that in the pulp chamber temperature increase was higher than that without resin. Starlight PRO, in the same condition of Valo lamp, showed a lower temperature increase in pre- and intrapolymerization. A control group (without composite resin) was evaluated. Significance. Temperature increase during resin curing is a function of the rate of polymerization, due to the exothermic polymerization reaction, the energy from the light unit, and time of exposure. PMID:27195282

Investigation on mechanical behavior and material characteristics of various weight composition of SiCp reinforced aluminium metal matrix composite

NASA Astrophysics Data System (ADS)

Pichumani, Sivachidambaram; Srinivasan, Raghuraman; Ramamoorthi, Venkatraman

2018-02-01

Aluminium - silicon carbide (Al - SiC) metal matrix composite is produced with following wt % of SiC reinforcement (4%, 8% & 12%) using stir casting method. Mechanical testing such as micro hardness, tensile testing and bend testing were performed. Characterizations, namely micro structure, X-ray diffraction (XRD) analysis, inductive coupled plasma - optical emission spectroscopy (ICP-OES) and scanning electron microscopy (SEM) analysis, were carried out on Al - SiC composites. The presence of SiC on Al - SiC composite is confirmed through XRD technique and microstructure. The percentage of SiC was confirmed through ICP-OES technique. Increase in weight percentage of SiC tends to increase micro hardness, ultimate strength & yield strength but it reduces the bend strength and elongation (%) of the material. SEM factrography of tensile tested fractured samples of Al - 8% SiC & Al - 12% SiC showed fine dimples on fractured surface & coarse dimples fractured surface respectively. This showed significant fracture differences between Al - 8% SiC & Al - 12% SiC. From the above experiment, Al - 8% SiC had good micro hardness, ultimate strength & yield strength without significant loss in elongation (%) & bend strength.

Design and Test Research on Cutting Blade of Corn Harvester Based on Bionic Principle.

PubMed

Tian, Kunpeng; Li, Xianwang; Zhang, Bin; Chen, Qiaomin; Shen, Cheng; Huang, Jicheng

2017-01-01

Existing corn harvester cutting blades have problems associated with large cutting resistance, high energy consumption, and poor cut quality. Using bionics principles, a bionic blade was designed by extracting the cutting tooth profile curve of the B. horsfieldi palate. Using a double-blade cutting device testing system, a single stalk cutting performance contrast test for corn stalks obtained at harvest time was carried out. Results show that bionic blades have superior performance, demonstrated by strong cutting ability and good cut quality. Using statistical analysis of two groups of cutting test data, the average cutting force and cutting energy of bionic blades and ordinary blades were obtained as 480.24 N and 551.31 N and 3.91 J and 4.38 J, respectively. Average maximum cutting force and cutting energy consumption for the bionic blade were reduced by 12.89% and 10.73%, respectively. Variance analysis showed that both blade types had a significant effect on maximum cutting energy and cutting energy required to cut a corn stalk. This demonstrates that bionic blades have better cutting force and energy consumption reduction performance than ordinary blades.

Recovery of dynamic balance after general anesthesia with sevoflurane in short-duration oral surgery.

PubMed

Fujisawa, Toshiaki; Miyamoto, Eriko; Takuma, Shigeru; Shibuya, Makiko; Kurozumi, Akihiro; Kimura, Yukifumi; Kamekura, Nobuhito; Fukushima, Kazuaki

2009-01-01

Recovery of dynamic balance, involving adjustment of the center of gravity, is essential for safe discharge on foot after ambulatory anesthesia. The purpose of this study was to assess the recovery of dynamic balance after general anesthesia with sevoflurane, using two computerized dynamic posturographies. Nine hospitalized patients undergoing oral surgery of less than 2 h duration under general anesthesia (air-oxygensevoflurane) were studied. A dynamic balance test, assessing the ability of postural control against unpredictable perturbation stimuli (Stability System; Biodex Medical), a walking analysis test using sheets with foot pressure sensors (Walk Way-MG1000; Anima), and two simple psychomotor function tests were performed before anesthesia (baseline), and 150 and 210 min after the emergence from anesthesia. Only the double-stance phase in the walking analysis test showed a significant difference between baseline and results at 150 min. None of the other variables showed any differences among results at baseline and at 150 and 210 min. The recovery times for dynamic balance and psychomotor function seem to be within 150 min after emergence from general anesthesia with sevoflurane in patients undergoing oral surgery of less than 2-h duration.

LED Curing Lights and Temperature Changes in Different Tooth Sites.

PubMed

Armellin, E; Bovesecchi, G; Coppa, P; Pasquantonio, G; Cerroni, L

2016-01-01

Objectives. The aim of this in vitro study was to assess thermal changes on tooth tissues during light exposure using two different LED curing units. The hypothesis was that no temperature increase could be detected within the dental pulp during polymerization irrespective of the use of a composite resin or a light-curing unit. Methods. Caries-free human first molars were selected, pulp residues were removed after root resection, and four calibrated type-J thermocouples were positioned. Two LED lamps were tested; temperature measurements were made on intact teeth and on the same tooth during curing of composite restorations. The data was analyzed by one-way analysis of variance (ANOVA), Wilcoxon test, Kruskal-Wallis test, and Pearson's χ (2). After ANOVA, the Bonferroni multiple comparison test was performed. Results. Polymerization data analysis showed that in the pulp chamber temperature increase was higher than that without resin. Starlight PRO, in the same condition of Valo lamp, showed a lower temperature increase in pre- and intrapolymerization. A control group (without composite resin) was evaluated. Significance. Temperature increase during resin curing is a function of the rate of polymerization, due to the exothermic polymerization reaction, the energy from the light unit, and time of exposure.

Episodic and working memory function in Primary Progressive Aphasia: A meta-analysis.

PubMed

Eikelboom, Willem S; Janssen, Nikki; Jiskoot, Lize C; van den Berg, Esther; Roelofs, Ardi; Kessels, Roy P C

2018-06-18

The distinction between Primary Progressive Aphasia (PPA) variants remains challenging for clinicians, especially for the non-fluent (nfv-PPA) and the logopenic variants (lv-PPA). Previous research suggests that memory tests might aid this differentiation. This meta-analysis compares memory function among PPA variants. Effects sizes were extracted from 41 studies (N = 849). Random-effects models were used to compare performance on episodic and working memory tests among PPA patients and healthy controls, and between the PPA variants. Memory deficits were frequently observed in PPA compared to controls, with large effect sizes for lv-PPA (Hedges' g = -2.04 [-2.58 to -1.49]), nfv-PPA (Hedges' g = -1.34 [-1.69 to -1.00]), and the semantic variant (sv-PPA; Hedges' g = -1.23 [-1.50 to -0.97]). Sv-PPA showed primarily verbal memory deficits, whereas lv-PPA showed worse performance than nfv-PPA on both verbal and non-verbal memory tests. Memory deficits were more pronounced in lv-PPA compared to nfv-PPA. This suggests that memory tests may be helpful to distinguish between these PPA variants. Copyright © 2018. Published by Elsevier Ltd.

RAS testing and cetuximab treatment for metastatic colorectal cancer: a cost-effectiveness analysis in a setting with limited health resources.

PubMed

Wu, Bin; Yao, Yuan; Zhang, Ke; Ma, Xuezhen

2017-09-19

To test the cost-effectiveness of cetuximab plus irinotecan, fluorouracil, and leucovorin (FOLFIRI) as first-line treatment in patients with metastatic colorectal cancer (mCRC) from a Chinese medical insurance perspective. Baseline analysis showed that the addition of cetuximab increased quality-adjusted life-years (QALYs) by 0.63, an increase of $17,086 relative to FOLFIRI chemotherapy, resulting in an incremental cost-effectiveness ratio (ICER) of $27,145/QALY. When the patient assistance program (PAP) was available, the ICER decreased to $14,049/QALY, which indicated that the cetuximab is cost-effective at a willingness-to-pay threshold of China ($22,200/QALY). One-way sensitivity analyses showed that the median overall survival time for the cetuximab was the most influential parameter. A Markov model by incorporating clinical, utility and cost data was developed to evaluate the economic outcome of cetuximab in mCRC. The lifetime horizon was used, and sensitivity analyses were carried out to test the robustness of the model results. The impact of PAP was also evaluated in scenario analyses. RAS testing with cetuximab treatment is likely to be cost-effective for patients with mCRC when PAP is available in China.

Economic evaluation of an intensified disease management system for patients with type 2 diabetes.

PubMed

Lairson, David R; Yoon, Seok-Jun; Carter, Patrick M; Greisinger, Anthony J; Talluri, Krishna C; Aggarwal, Manish; Wehmanen, Oscar

2008-04-01

We evaluated the effect of a disease management (DM) program on adherence with recommended laboratory tests, health outcomes, and health care expenditures for patients with type 2 diabetes. The study was a natural experiment in a primary care setting in which the intervention was available to 1 group and then compared to the experience of a matched control group. Univariate analysis and difference in differences analysis were used to test for any significant differences between the 2 groups following a 12-month intervention period. A payer perspective was used to estimate the health care cost consequences based on hospital and physician utilization weighted by Medicare prices. The results were nonsignificant at the .10 level, except for compliance with recommended tests, which showed significant results in the univariate analysis. The intervention increased compliance with testing for HbA1c, microalbuminuria, and lipids, and decreased HbA1c value and the percent of patients with HbA1c >or=9.5%. The point estimates showed small reductions in health care cost; only reductions in costs for office visits were significant at the .10 level. We concluded that while there were signs of improvement in adherence to testing, the low effectiveness may be attributed to existing diabetes management activities in this primary care setting, high compliance rates for testing at the beginning of the study, and a steep learning curve for this complex, information-technology-based DM system. The study raises questions about the incremental gains from complex systems approaches to DM and illustrates a rigorous method to assess DM programs under "real-world" conditions, with control for possible selection bias.

INNOVATIVE INSTRUMENTATION AND ANALYSIS OF THE TEMPERATURE MEASUREMENT FOR HIGH TEMPERATURE GASIFICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seong W. Lee

2004-10-01

The systematic tests of the gasifier simulator on the clean thermocouple were completed in this reporting period. Within the systematic tests on the clean thermocouple, five (5) factors were considered as the experimental parameters including air flow rate, water flow rate, fine dust particle amount, ammonia addition and high/low frequency device (electric motor). The fractional factorial design method was used in the experiment design with sixteen (16) data sets of readings. Analysis of Variances (ANOVA) was applied to the results from systematic tests. The ANOVA results show that the un-balanced motor vibration frequency did not have the significant impact onmore » the temperature changes in the gasifier simulator. For the fine dust particles testing, the amount of fine dust particles has significant impact to the temperature measurements in the gasifier simulator. The effects of the air and water on the temperature measurements show the same results as reported in the previous report. The ammonia concentration was included as an experimental parameter for the reducing environment in this reporting period. The ammonia concentration does not seem to be a significant factor on the temperature changes. The linear regression analysis was applied to the temperature reading with five (5) factors. The accuracy of the linear regression is relatively low, which is less than 10% accuracy. Nonlinear regression was also conducted to the temperature reading with the same factors. Since the experiments were designed in two (2) levels, the nonlinear regression is not very effective with the dataset (16 readings). An extra central point test was conducted. With the data of the center point testing, the accuracy of the nonlinear regression is much better than the linear regression.« less

The effectiveness of learning with concept mapping on the science problem-solving of sixth-grade children

NASA Astrophysics Data System (ADS)

Jolly, Anju B.

The purpose of this study was to analyze the relationship of concept mapping to science problem solving in sixth grade elementary school children. The study proposes to determine whether the students' ability to perform higher cognitive processes was a predictor of students' performance in solving problems in science and whether gender and socioeconomic status are related to performance in solving problems. Two groups participated in the study. Both groups were given a pre-test of higher cognitive ability--the Ross Test of Higher Cognitive Ability. One group received instruction on a science unit of study in concept mapping format and the other group received instruction in traditional format. The instruction lasted approximately 4 weeks. Both groups were given a problem-solving post-test. A comparison of post-test means was done using Analysis of Covariance (ANCOVA) as the statistical procedure with scores on the test of higher cognitive ability as the covariate. Also, Multiple Regression was performed to analyze the influence of participants' gender and socioeconomic status on their performance in solving problems. Results from the analysis of covariance showed that the group receiving instruction in the concept mapping format performed significantly better than the group receiving instruction in traditional format. Also the Ross Test of Higher Cognitive Processes emerged to be a predictor of performance on problem solving. There was no significant difference in the analysis of the performance of males and females. No pattern emerged regarding the influence of socioeconomic status on problem solving performance. In conclusion, the study showed that concept mapping improved problem solving in the classroom, and that gender and socioeconomic status are not predictors of student success in problem solving.

Forecast and analysis of the cosmological redshift drift.

PubMed

Lazkoz, Ruth; Leanizbarrutia, Iker; Salzano, Vincenzo

2018-01-01

The cosmological redshift drift could lead to the next step in high-precision cosmic geometric observations, becoming a direct and irrefutable test for cosmic acceleration. In order to test the viability and possible properties of this effect, also called Sandage-Loeb (SL) test, we generate a model-independent mock data set in order to compare its constraining power with that of the future mock data sets of Type Ia Supernovae (SNe) and Baryon Acoustic Oscillations (BAO). The performance of those data sets is analyzed by testing several cosmological models with the Markov chain Monte Carlo (MCMC) method, both independently as well as combining all data sets. Final results show that, in general, SL data sets allow for remarkable constraints on the matter density parameter today [Formula: see text] on every tested model, showing also a great complementarity with SNe and BAO data regarding dark energy parameters.

Analyzing the Influence of a New Dental Implant Design on Primary Stability.

PubMed

Valente, Mariana Lima da Costa; de Castro, Denise Tornavoi; Shimano, Antonio Carlos; Lepri, César Penazzo; dos Reis, Andréa Cândido

2016-02-01

The macrogeometry of dental implants strongly influences the primary stability and hence the osseointegration process. Compare the performance of conventional and modified implant models in terms of primary stability. A total of 36 implants (Neodent®) with two different formats (n = 18): Alvim CM (Conical CM, Ø 4.3 mm × 10 mm in length) and Titamax Ti (Cylindrical HE, Ø 4.0 mm × 11 mm in length) were inserted into artificial bone blocks. Nine implants from each set were selected to undergo external geometry changes. The primary stability was quantified by insertion torque and resonance frequency using an Osstell device and the pullout test. One-way analysis of variance and Tukey's test were used for statistical evaluation. The comparative analysis of the implants showed a significant increase of the insertion torque for the modified Conical CM implants (p = 0.000) and Cylindrical HE (p = 0.043); for the resonance frequency the modified Cylindrical HE showed a lower statistical mean (p = 0.002) when compared to the conventional model, and in the pullout test both modified implants showed significant reduction (p = 0.000). Within the limitations of this study, the proposed modification showed good stability levels and advantages when compared to the conventional implants. © 2015 Wiley Periodicals, Inc.

Statistical analysis of trends in monthly precipitation at the Limbang River Basin, Sarawak (NW Borneo), Malaysia

NASA Astrophysics Data System (ADS)

Krishnan, M. V. Ninu; Prasanna, M. V.; Vijith, H.

2018-05-01

Effect of climate change in a region can be characterised by the analysis of rainfall trends. In the present research, monthly rainfall trends at Limbang River Basin (LRB) in Sarawak, Malaysia for a period of 45 years (1970-2015) were characterised through the non-parametric Mann-Kendall and Spearman's Rho tests and relative seasonality index. Statistically processed monthly rainfall of 12 well distributed rain gauging stations in LRB shows almost equal amount of rainfall in all months. Mann-Kendall and Spearman's Rho tests revealed a specific pattern of rainfall trend with a definite boundary marked in the months of January and August with positive trends in all stations. Among the stations, Limbang DID, Long Napir and Ukong showed positive (increasing) trends in all months with a maximum increase of 4.06 mm/year (p = 0.01) in November. All other stations showed varying trends (both increasing and decreasing). Significant (p = 0.05) decreasing trend was noticed in Ulu Medalam and Setuan during September (- 1.67 and - 1.79 mm/year) and October (- 1.59 and - 1.68 mm/year) in Mann-Kendall and Spearman's Rho tests. Spatial pattern of monthly rainfall trends showed two clusters of increasing rainfalls (maximas) in upper and lower part of the river basin separated with a dominant decreasing rainfall corridor. The results indicate a generally increasing trend of rainfall in Sarawak, Borneo.

[Study of the consequences to the health of the Urkutsk Region's population from nuclear explosions at the Semipalatinsk testing site].

PubMed

Rukavishnikov, V S; Efimova, N V; Katul'skaia, O Iu; Cherniago, B P; Matorova, N I; Beliaeva, T A; Medvedev, V I

2009-01-01

Analysis of archival records on the activity of diurnal plane-tables from the region's weather stations revealed local radioactive fall-out in the near-Baikal areas from the nuclear weapon tests carried out at the Semipalatinsk testing site. Examination of mortality rates in the settlements exposed to the tests showed that the maximum rates of overall and lung malignancy mortalities were observed in 1960-1979; the mean radiation dose in the exposed settlements were estimated to be 580-850 MeV.

Evaluation of recovery and quality of sexual activity in women during postpartum in relation to the different mode of delivery: a retrospective analysis.

PubMed

Laganà, A S; Burgio, M A; Ciancimino, L; Sicilia, A; Pizzo, A; Magno, C; Butticè, S; Triolo, O

2015-08-01

Aim of the study was to assess the recovery and quality of sexual activity of women during postpartum, in relation to delivery. We recruited 200 women at 8 weeks after delivery. For each patient we recorded mode of delivery, age, body mass index (BMI), parity and test Female Sexual Function Index (FSFI) score. Sixty-four women (32%) had spontaneous deliveries without episiotomy, 48 (24%) had it with episiotomy, 88 (44%) had caesarean sections. The analysis of variance (ANOVA) test showed no significant differences among the 3 groups for age, BMI, parity. The test FSFI evidenced 68 cases (34%) of Regular Female Sexual Function (RFSF) and 132 (66%) of Female Sexual Dysfunction (FSD). The ANOVA test showed significant differences among the 3 groups in RFSF (F [2, 14]=8.075, P=0.005), but not in FSD (F [2, 30]=2.646, P=0.087). In RFSF, FSFI score was higher in women who had vaginal delivery with episiotomy compared with the other two groups. Conversely, in FSD (both with or without resumed sexual activity at 8 weeks postpartum) we evidenced that patients who had vaginal delivery with episiotomy showed lower FSFI score than the other two groups, with a decrease in lubrication, orgasm and satisfaction scores. Furthermore, we observed that most of the RFSF patients had a job and breastfed. Our results did not evidence a direct and significant correlation between mode of delivery and onset of female postpartum sexual dysfunction, even if FSD patients who underwent episiotomy during delivery markedly showed low FSFI scores.

Parallel processing methods for space based power systems

NASA Technical Reports Server (NTRS)

Berry, F. C.

1993-01-01

This report presents a method for doing load-flow analysis of a power system by using a decomposition approach. The power system for the Space Shuttle is used as a basis to build a model for the load-flow analysis. To test the decomposition method for doing load-flow analysis, simulations were performed on power systems of 16, 25, 34, 43, 52, 61, 70, and 79 nodes. Each of the power systems was divided into subsystems and simulated under steady-state conditions. The results from these tests have been found to be as accurate as tests performed using a standard serial simulator. The division of the power systems into different subsystems was done by assigning a processor to each area. There were 13 transputers available, therefore, up to 13 different subsystems could be simulated at the same time. This report has preliminary results for a load-flow analysis using a decomposition principal. The report shows that the decomposition algorithm for load-flow analysis is well suited for parallel processing and provides increases in the speed of execution.

Functional Analysis of Problem Behavior: A Systematic Approach for Identifying Idiosyncratic Variables

PubMed Central

Roscoe, Eileen M.; Schlichenmeyer, Kevin J.; Dube, William V.

2015-01-01

When inconclusive functional analysis (FA) outcomes occur, a number of modifications have been made to enhance the putative establishing operation or consequence associated with behavioral maintenance. However, a systematic method for identifying relevant events to test during modified FAs has not been evaluated. The purpose of this study was to develop and evaluate a technology for systematically identifying events to test in a modified FA after an initial FA led to inconclusive outcomes. Six individuals whose initial FA showed little or no responding or high levels only in the control condition participated. An indirect assessment (IA) questionnaire developed for identifying idiosyncratic variables was administered, and a descriptive analysis (DA) was conducted. Results from the IA only or a combination of the IA and DA were used to inform modified FA test and control conditions. Conclusive FA outcomes were obtained with five of the six participants during the modified FA phase. PMID:25930176

Construct validity of the Free and Cued Selective Reminding Test in older adults with memory complaints.

PubMed

Clerici, Francesca; Ghiretti, Roberta; Di Pucchio, Alessandra; Pomati, Simone; Cucumo, Valentina; Marcone, Alessandra; Vanacore, Nicola; Mariani, Claudio; Cappa, Stefano Francesco

2017-06-01

The Free and Cued Selective Reminding Test (FCSRT) is the memory test recommended by the International Working Group on Alzheimer's disease (AD) for the detection of amnestic syndrome of the medial temporal type in prodromal AD. Assessing the construct validity and internal consistency of the Italian version of the FCSRT is thus crucial. The FCSRT was administered to 338 community-dwelling participants with memory complaints (57% females, age 74.5 ± 7.7 years), including 34 with AD, 203 with Mild Cognitive Impairment, and 101 with Subjective Memory Impairment. Internal Consistency was estimated using Cronbach's alpha coefficient. To assess convergent validity, five FCSRT scores (Immediate Free Recall, Immediate Total Recall, Delayed Free Recall, Delayed Total Recall, and Index of Sensitivity of Cueing) were correlated with three well-validated memory tests: Story Recall, Rey Auditory Verbal Learning test, and Rey Complex Figure (RCF) recall (partial correlation analysis). To assess divergent validity, a principal component analysis (an exploratory factor analysis) was performed including, in addition to the above-mentioned memory tasks, the following tests: Word Fluencies, RCF copy, Clock Drawing Test, Trail Making Test, Frontal Assessment Battery, Raven Coloured Progressive Matrices, and Stroop Colour-Word Test. Cronbach's alpha coefficients for immediate recalls (IFR and ITR) and delayed recalls (DFR and DTR) were, respectively, .84 and .81. All FCSRT scores were highly correlated with those of the three well-validated memory tests. The factor analysis showed that the FCSRT does not load on the factors saturated by non-memory tests. These findings indicate that the FCSRT has a good internal consistency and has an excellent construct validity as an episodic memory measure. © 2015 The British Psychological Society.

Aquifer test interpretation using derivative analysis and diagnostic plots

NASA Astrophysics Data System (ADS)

Hernández-Espriú, Antonio; Real-Rangel, Roberto; Cortés-Salazar, Iván; Castro-Herrera, Israel; Luna-Izazaga, Gabriela; Sánchez-León, Emilio

2017-04-01

Pumping tests remain a method of choice to deduce fundamental aquifer properties and to assess well condition. In the oil and gas (O&G) industry, well testing has been the core technique in examining reservoir behavior over the last 50 years. The pressure derivative by Bourdet, it is perhaps, the most significant single development in the history of well test analysis. Recently, the so-called diagnostics plots (e.g. drawdown and drawdown derivative in a log-log plot) have been successfully tested in aquifers. However, this procedure is still underutilized by groundwater professionals. This research illustrates the applicability range, advantages and drawbacks (e.g. smoothing procedures) of diagnostic plots using field examples from a wide spectrum of tests (short/long tests, constant/variable flow rates, drawdown/buildup stages, pumping well/observation well) in dissimilar geological conditions. We analyze new and pre-existent aquifer tests in Mexico, USA, Canada, Germany, France and Saudi Arabia. In constant flow rate tests, our results show that derivative analysis is an easy, robust and powerful tool to assess near-borehole damage effects, formation heterogeneity, boundaries, flow regimes, infinite-acting radial stages, i.e., valid Theisian framework, and fracture-driven flow. In step tests, the effectiveness relies on high-frequency drawdown measurements. Moreover, we adapt O&G analytical solutions to cater for the conditions in groundwater systems. In this context, further parameters can be computed analytically from the plots, such as skin factor, head losses, wellbore storage, distance to the boundary, channel-aquifer and/or fracture zone width, among others. Therefore, diagnostic plots should be considered a mandatory tool for pumping tests analysis among hydrogeologists. This project has been supported by DGAPA (UNAM) under the research project PAPIIT IN-112815.

Testing the equivalence principle on cosmological scales

NASA Astrophysics Data System (ADS)

Bonvin, Camille; Fleury, Pierre

2018-05-01

The equivalence principle, that is one of the main pillars of general relativity, is very well tested in the Solar system; however, its validity is more uncertain on cosmological scales, or when dark matter is concerned. This article shows that relativistic effects in the large-scale structure can be used to directly test whether dark matter satisfies Euler's equation, i.e. whether its free fall is characterised by geodesic motion, just like baryons and light. After having proposed a general parametrisation for deviations from Euler's equation, we perform Fisher-matrix forecasts for future surveys like DESI and the SKA, and show that such deviations can be constrained with a precision of order 10%. Deviations from Euler's equation cannot be tested directly with standard methods like redshift-space distortions and gravitational lensing, since these observables are not sensitive to the time component of the metric. Our analysis shows therefore that relativistic effects bring new and complementary constraints to alternative theories of gravity.

Comparative study of the chemical profiling, antioxidant and antimicrobial activities of essential oils of different parts of Thymus willdenowii Boiss & Reut.

PubMed

Ouknin, Mohamed; Romane, Abderrahmane; Costa, Jean; Majidi, Lhou

2018-02-27

The analysis of Thymus willdenowii Boiss & Reut essential oils (TW EOs) shows 33 components accounting for (96.3-97.7%) of all identified. The main constituents of TW EOs were thymol (35.5-47.3%), p-cymene (13.9-23.8%), γ-terpinene (8.9-20.3%). The antioxidant assays revealed that all TW EOs tested showed strong activities, the antimicrobial effect of TW EOs has been tested against isolated clinical strains of Proteus mirabilis (ATCC 35659), Escherichia coli (ATCC 25922), Candida albicans (ATCC 10231), Bacillus cereus (ATCC 10876), and Aspergillus brasilliensis (ATCC 16404). The antimicrobial test indicates that TW EOs show an inhibition effect against all the tested bacteria with a MIC of 6.9 to 27.6 μg/mL -1 . These results proving that the essential oils extracted from Thymus willdenowii Boiss & Reut may be a new potential source of natural antimicrobial applied in pharmaceutical and food industries.

Comparative Evaluation of Stress Distribution in Experimentally Designed Nickel-titanium Rotary Files with Varying Cross Sections: A Finite Element Analysis.

PubMed

Basheer Ahamed, Shadir Bughari; Vanajassun, Purushothaman Pranav; Rajkumar, Kothandaraman; Mahalaxmi, Sekar

2018-04-01

Single cross-sectional nickel-titanium (NiTi) rotary instruments during continuous rotations are subjected to constant and variable stresses depending on the canal anatomy. This study was intended to create 2 new experimental, theoretic single-file designs with combinations of triple U (TU), triangle (TR), and convex triangle (CT) cross sections and to compare their bending stresses in simulated root canals with a single cross-sectional instrument using finite element analysis. A 3-dimensional model of the simulated root canal with 45° curvature and NiTi files with 5 cross-sectional designs were created using Pro/ENGINEER Wildfire 4.0 software (PTC Inc, Needham, MA) and ANSYS software (version 17; ANSYS, Inc, Canonsburg, PA) for finite element analysis. The NiTi files of 3 groups had single cross-sectional shapes of CT, TR, and TU designs, and 2 experimental groups had a CT, TR, and TU (CTU) design and a TU, TR, and CT (UTC) design. The file was rotated in simulated root canals to analyze the bending stress, and the von Mises stress value for every file was recorded in MPa. Statistical analysis was performed using the Kruskal-Wallis test and the Bonferroni-adjusted Mann-Whitney test for multiple pair-wise comparison with a P value <.05 (95 %). The maximum bending stress of the rotary file was observed in the apical third of the CT design, whereas comparatively less stress was recorded in the CTU design. The TU and TR designs showed a similar stress pattern at the curvature, whereas the UTC design showed greater stress in the apical and middle thirds of the file in curved canals. All the file designs showed a statistically significant difference. The CTU designed instruments showed the least bending stress on a 45° angulated simulated root canal when compared with all the other tested designs. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Subsurface profiling using integrated geophysical methods for 2D site response analysis in Bangalore city, India: a new approach

NASA Astrophysics Data System (ADS)

Chandran, Deepu; Anbazhagan, P.

2017-10-01

Recently, site response analysis has become a mandatory step for the design of important structures. Subsurface investigation is an essential step, from where the input parameters for the site response study like density, shear wave velocity (Vs), thickness and damping characteristics, etc, are obtained. Most site response studies at shallow bedrock sites are one-dimensional (1D) and are usually carried out by using Vs from multi-channel analysis of surface waves (MASW) or a standard penetration test (SPT) for N values with assumptions that soil layers are horizontal, uniform and homogeneous. These assumptions are not completely true in shallow bedrock regions as soil deposits are heterogeneous. The objective of this study is to generate the actual subsurface profiles in two-dimensions at shallow bedrock regions using integrated subsurface investigation testing. The study area selected for this work is Bangalore, India. Three survey lines were selected in Bangalore at two different locations; one at the Indian Institute of Science (IISc) Campus and the other at Whitefield. Geophysical surveys like ground penetrating radar (GPR) and 2D MASW were carried out at these survey lines. Geophysical test results are compared and validated with a conventional geotechnical SPT. At the IISc site, the soil profile is obtained from a trench excavated for a proposed pipeline used to compare the geophysical test results. Test results show that GPR is very useful to delineate subsurface layers, especially for shallow depths at both sites (IISc Campus and Whitefield). MASW survey results show variation of Vs values and layer thickness comparatively at deeper depths for both sites. They also show higher density soil strata with high Vs value obtained at the IISc Campus site, whereas at the Whitefield site weaker soil with low shear velocity is observed. Combining these two geophysical methods helped to generate representative 2D subsurface profiles. These subsurface profiles can be further used to understand the difference between 1D and 2D site response.

Visual associations cued recall A Paradigm for Measuring Episodic Memory Decline in Alzheimer's Disease.

PubMed

Meyer, Sascha R A; Spaan, Pauline E J; Boelaarts, Leo; Ponds, Rudolf W H M; Schmand, Ben; de Jonghe, Jos F M

2016-09-01

Repeated measurements of episodic memory are needed for monitoring amnestic mild cognitive impairment (aMCI) and mild Alzheimer's disease (AD). Most episodic memory tests may pose a challenge to patients, even when they are in the milder stages of the disease. This cross-sectional study compared floor effects of the Visual Association Test (VAT) and the Rey Auditory Verbal Learning Test (RAVLT) in healthy elderly controls and in patients with aMCI or AD (N = 125). A hierarchical multiple regression analysis was used to examine whether linear or quadratic trends best fitted the data of cognitive test performance across global cognitive impairment. Results showed that VAT total scores decreased linearly across the range of global cognitive impairment, whereas RAVLT total scores showed a quadratic trend, with total scores levelling off for 90% of aMCI patients and 94% of AD patients. We conclude that the VAT shows few if any floor effects in patients with aMCI and mild AD and is therefore a potentially promising cognitive test for monitoring episodic memory impairment.

Effect of a virtual environment on the development of mathematical skills in children with dyscalculia.

PubMed

de Castro, Marcus Vasconcelos; Bissaco, Márcia Aparecida Silva; Panccioni, Bruno Marques; Rodrigues, Silvia Cristina Martini; Domingues, Andreia Miranda

2014-01-01

In this study, we show the effectiveness of a virtual environment comprising 18 computer games that cover mathematics topics in a playful setting and that can be executed on the Internet with the possibility of player interaction through chat. An arithmetic pre-test contained in the Scholastic Performance Test was administered to 300 children between 7 and 10 years old, including 162 males and 138 females, in the second grade of primary school. Twenty-six children whose scores showed a low level of mathematical knowledge were chosen and randomly divided into the control (CG) and experimental (EG) groups. The EG participated to the virtual environment and the CG participated in reinforcement using traditional teaching methods. Both groups took a post-test in which the Scholastic Performance Test (SPT) was given again. A statistical analysis of the results using the Student's t-test showed a significant learning improvement for the EG and no improvement for the CG (p≤0.05). The virtual environment allows the students to integrate thought, feeling and action, thus motivating the children to learn and contributing to their intellectual development.

An innovative distillation device for tritiated water analysis with high decontamination factor.

PubMed

Fang, Hsin-Fa; Wang, Chu-Fang; Wang, Jeng-Jong

2013-11-01

Institute of Nuclear Energy Research (INER) has designed an air-cooling distillation device and got a US patent. The decontamination factor (60)Co and (137)Cs is above 23,000. Tritium loss rate is one of testing items in ASTM D4107 Standard Test Method for Tritium in Drinking Water. In this study, the 3 levels (high, middle and low level) of tritium concentration of testing samples for the loss rate test were prepared similar to the concentrations reported in ASTM D4107. The loss rate of the high level is -2.37%, the middle is -2.31% and the low level is -2.47%. These results show that the air-cooling distillation device has good performance in the environmental water tritium analysis work. Copyright © 2013 Elsevier Ltd. All rights reserved.

The development and psychometric testing of East Asian Acculturation Scale among Asian immigrant women in Taiwan.

PubMed

Kuo, Shu-Fen; Chang, Wen-Yin; Chang, Lu-I; Chou, Yu-Hua; Chen, Ching-Min

2013-01-01

This is a report of development and psychometric testing of the East Asian Acculturation Measure-Chinese version (EAAM-C) scale. An instrument validation design with a cross-sectional survey was conducted. The process was carried in two phases. In Phase 1, Barry's East Asian Acculturation Measure was translated and back translated to evaluate its content, face validity, and feasibility validity. In Phase 2, the 16-item EAAM-C was pilot-tested among 485 female immigrants for test-retest reliability, internal consistency, theoretically-supported construct validity and concurrent validity. The pilot work and the survey results indicated the tools possessed adequate content and face validity. The Cronbach's Alphas for the EAAM-C was 0.72, and 0.76-0.79 for its subscales, and the correlation of test-retest reliability (at 3 weeks) was 0.75. After dropping one item, four theoretically-supported factors which explained 61.82% of the variance were abstracted using exploratory factor analysis: assimilation, integration, separation, and marginalization. Based on the underlying four-factor theoretical structures of the EAAM, the confirmatory factor analysis of the EAAM-C was further examined. The analysis revealed that the four-factor model was an acceptable fit for the data which demonstrated adequate finding in its construct validity. These factors were inter-correlated, and showed statistically significant correlation with the Chinese Health Questionnaire, indicating adequate concurrent validity. The scale shows acceptable validity and consistency, and suggests that immigrant acculturation is a complex construct. This quick evaluation instrument can be applied to assess clients' acculturation and in further developing certain interventions to improve their health.

Individual Test Point Fluctuations of Macular Sensitivity in Healthy Eyes and Eyes With Age-Related Macular Degeneration Measured With Microperimetry.

PubMed

Barboni, Mirella Telles Salgueiro; Szepessy, Zsuzsanna; Ventura, Dora Fix; Németh, János

2018-04-01

To establish fluctuation limits, it was considered that not only overall macular sensitivity but also fluctuations of individual test points in the macula might have clinical value. Three repeated measurements of microperimetry were performed using the Standard Expert test of Macular Integrity Assessment (MAIA) in healthy subjects ( N = 12, age = 23.8 ± 1.5 years old) and in patients with age-related macular degeneration (AMD) ( N = 11, age = 68.5 ± 7.4 years old). A total of 37 macular points arranged in four concentric rings and in four quadrants were analyzed individually and in groups. The data show low fluctuation of macular sensitivity of individual test points in healthy subjects (average = 1.38 ± 0.28 dB) and AMD patients (average = 2.12 ± 0.60 dB). Lower sensitivity points are more related to higher fluctuation than to the distance from the central point. Fixation stability showed no effect on the sensitivity fluctuation. The 95th percentile of the standard deviations of healthy subjects was, on average, 2.7 dB, ranging from 1.2 to 4 dB, depending on the point tested. Point analysis and regional analysis might be considered prior to evaluating macular sensitivity fluctuation in order to distinguish between normal variation and a clinical change. S tatistical methods were used to compare repeated microperimetry measurements and to establish fluctuation limits of the macular sensitivity. This analysis could add information regarding the integrity of different macular areas and provide new insights into fixation points prior to the biofeedback fixation training.

Breath tests sustainability in hospital settings: cost analysis and reimbursement in the Italian National Health System.

PubMed

Volpe, M; Scaldaferri, F; Ojetti, V; Poscia, A

2013-01-01

The high demand of Breath Tests (BT) in many gastroenterological conditions in time of limited resources for health care systems, generates increased interest in cost analysis from the point of view of the delivery of services to better understand how use the money to generate value. This study aims to measure the cost of C13 Urea and other most utilized breath tests in order to describe key aspects of costs and reimbursements looking at the economic sustainability for the hospital. A hospital based cost-analysis of the main breath tests commonly delivery in an ambulatory setting is performed. Mean salary for professional nurses and gastroenterologists, drugs/preparation used and disposable materials, purchase and depreciation of the instrument and the testing time was used to estimate the cost, while reimbursements are based on the 2013 Italian National Health System ambulatory pricelist. Variables that could influence the model are considered in the sensitivity analyses. The mean cost for C13--Urea, Lactulose and Lactose BT are, respectively, Euros 30,59; 45,20 and 30,29. National reimbursement often doesn't cover the cost of the analysis, especially considering the scenario with lower number of exam. On the contrary, in high performance scenario all the reimbursement could cover the cost, except for the C13 Urea BT that is high influenced by the drugs cost. However, consideration about the difference between Italian Regional Health System ambulatory pricelist are done. Our analysis shows that while national reimbursement rates cover the costs of H2 breath testing, they do not cover sufficiently C13 BT, particularly urea breath test. The real economic strength of these non invasive tests should be considered in the overall organization of inpatient and outpatient clinic, accounting for complete diagnostic pathway for each gastrointestinal disease.

Dynamic Characteristics and Stability Analysis of Space Shuttle Main Engine Oxygen Pump

NASA Technical Reports Server (NTRS)

Gunter, Edgar J.; Branagan, Lyle

1991-01-01

The dynamic characteristics of the Space Shuttle high pressure oxygen pump are presented. Experimental data is presented to show the vibration spectrum and response under actual engine operation and also in spin pit testing for balancing. The oxygen pump appears to be operating near a second critical speed and is sensitive to self excited aerodynamic cross coupling forces in the turbine and pump. An analysis is presented to show the improvement in pump stability by the application of turbulent flow seals, preburner seals, and pump shaft cross sectional modifications.

Failure Analysis of a Service Tube

NASA Astrophysics Data System (ADS)

Xie, Zhongdong; Cai, Weiguo; Li, Zhenxing; Guan, YiMing; Zhang, Baocheng; Yang, XiaoTong

2017-12-01

One tube was cracked used in the primary reformer furnace in a fertilizer plant for two and half years. In order to find out the causes of cracking, the methods for chemical composition analysis, macro- and microstructure analysis, penetrant testing, weld analysis, crack and surface damage analysis, mechanics property analysis, high temperature endurance performance analysis, stress and wall thickness calculation were adopted. The integrated assessment results showed that the carbon content of the tube was in the lower limit of the standard range; the tube effective wall thickness was too small; local overheating leads to tube cracking in use process.

Handling nonnormality and variance heterogeneity for quantitative sublethal toxicity tests.

PubMed

Ritz, Christian; Van der Vliet, Leana

2009-09-01

The advantages of using regression-based techniques to derive endpoints from environmental toxicity data are clear, and slowly, this superior analytical technique is gaining acceptance. As use of regression-based analysis becomes more widespread, some of the associated nuances and potential problems come into sharper focus. Looking at data sets that cover a broad spectrum of standard test species, we noticed that some model fits to data failed to meet two key assumptions-variance homogeneity and normality-that are necessary for correct statistical analysis via regression-based techniques. Failure to meet these assumptions often is caused by reduced variance at the concentrations showing severe adverse effects. Although commonly used with linear regression analysis, transformation of the response variable only is not appropriate when fitting data using nonlinear regression techniques. Through analysis of sample data sets, including Lemna minor, Eisenia andrei (terrestrial earthworm), and algae, we show that both the so-called Box-Cox transformation and use of the Poisson distribution can help to correct variance heterogeneity and nonnormality and so allow nonlinear regression analysis to be implemented. Both the Box-Cox transformation and the Poisson distribution can be readily implemented into existing protocols for statistical analysis. By correcting for nonnormality and variance heterogeneity, these two statistical tools can be used to encourage the transition to regression-based analysis and the depreciation of less-desirable and less-flexible analytical techniques, such as linear interpolation.

Coding the echinoid skeleton - a quasimetric description of complex taphonomic pathways

NASA Astrophysics Data System (ADS)

Grun, Tobias; Nebelsick, James

2016-04-01

Taphonomic pathways determine the contribution of organisms remains to the fossil record. Skeletons which experience strong taphonomic processes can either be filtered out before they become fossilized or are highly affected and thus potentially bias paleontological analyses. The echinoid test is a multi-element skeleton and features a variety of micro- and macrostructural surface characters such as tubercles, ambulacral pores, genital pores and variations in stereom morphology. Although all characters are exposed to the environment, stereom differentiation as well as the spatial character distribution on the test can result in a range of taphonomic alteration grades on a single specimen. The present study is based on 1052 test of the minute clypeasteroid echinoid Echinocyamus pusillus from the Mediterranean Sea and is analyzed for fragmentation, encrustation as well as the abrasion of tubercles, stereom surface as well as genital- and ambulacral pores. The use of character coding including both taphonomic grades as well as spatial distributions of specific characters on the test results in a quasimetric and numerical description of taphonomic abrasion grades. These values can be handled as interval-scaled data thus enabling bi- and multivariate statistical analysis. Results show that the Mediterranean Echinocyamus tests are generally well preserved; abrasion values are low, fragmentation and encrustation is rare. A comparison of the surface characters shows that abrasion grades of the tubercles are higher than that of the surface stereom or pore margins. Exposed tubercles show significantly higher abrasion grades than sheltered tubercles of the peristomal area. Analysis also indicate that abrasion values increase significantly with increasing encrustation levels, which can be due to the fact that incrusting organisms cross plate boundaries and thus strengthen the structural integrity of the echinoid tests.

Evaluation of Fitness and the Balance Levels of Children with a Diagnosis of Juvenile Idiopathic Arthritis: A Pilot Study

PubMed Central

Maggio, Maria Cristina; Corsello, Giovanni; Messina, Giuseppe; Iovane, Angelo; Palma, Antonio

2017-01-01

Background: Juvenile idiopathic arthritis is a main cause of physical disability and has high economic costs for society. The purpose of this study was to assess the fitness levels and the postural and balance deficits with a specific test battery. Methods: Fifty-six subjects were enrolled in this study. Thirty-nine healthy subjects were included in the control group and seventeen in the juvenile idiopathic arthritis group. All subjects were evaluated using a posturography system. The fitness level was evaluated with a battery of tests (Abalakov test, sit-up test, hand grip test, backsaver sit and reach, the toe touch test). An unpaired t-test was used to determine differences. Pearson’s correlation coefficient was used to evaluate the correlation between the tests. Results: The battery of tests demonstrated that subjects in the juvenile idiopathic arthritis group have lower fitness levels compared to the control group. The juvenile idiopathic arthritis group showed low postural control with respect to the control group. Pearson analysis of the juvenile idiopathic arthritis group data showed significant correlations between variables. Pearson’s results from the control group data showed a similar trend. Conclusions: The results suggest that the battery of tests used could be an appropriate tool. However, we highlight that these conclusions need to be supported by other studies with a larger population scale. PMID:28753965

Evaluation of Fitness and the Balance Levels of Children with a Diagnosis of Juvenile Idiopathic Arthritis: A Pilot Study.

PubMed

Patti, Antonino; Maggio, Maria Cristina; Corsello, Giovanni; Messina, Giuseppe; Iovane, Angelo; Palma, Antonio

2017-07-19

Background: Juvenile idiopathic arthritis is a main cause of physical disability and has high economic costs for society. The purpose of this study was to assess the fitness levels and the postural and balance deficits with a specific test battery. Methods: Fifty-six subjects were enrolled in this study. Thirty-nine healthy subjects were included in the control group and seventeen in the juvenile idiopathic arthritis group. All subjects were evaluated using a posturography system. The fitness level was evaluated with a battery of tests (Abalakov test, sit-up test, hand grip test, backsaver sit and reach, the toe touch test). An unpaired t -test was used to determine differences. Pearson's correlation coefficient was used to evaluate the correlation between the tests. Results: The battery of tests demonstrated that subjects in the juvenile idiopathic arthritis group have lower fitness levels compared to the control group. The juvenile idiopathic arthritis group showed low postural control with respect to the control group. Pearson analysis of the juvenile idiopathic arthritis group data showed significant correlations between variables. Pearson's results from the control group data showed a similar trend. Conclusions: The results suggest that the battery of tests used could be an appropriate tool. However, we highlight that these conclusions need to be supported by other studies with a larger population scale.

Face Perception and Test Reliabilities in Congenital Prosopagnosia in Seven Tests

PubMed Central

Esins, Janina; Schultz, Johannes; Stemper, Claudia; Kennerknecht, Ingo

2016-01-01

Congenital prosopagnosia, the innate impairment in recognizing faces, is a very heterogeneous disorder with different phenotypical manifestations. To investigate the nature of prosopagnosia in more detail, we tested 16 prosopagnosics and 21 controls with an extended test battery addressing various aspects of face recognition. Our results show that prosopagnosics exhibited significant impairments in several face recognition tasks: impaired holistic processing (they were tested amongst others with the Cambridge Face Memory Test (CFMT)) as well as reduced processing of configural information of faces. This test battery also revealed some new findings. While controls recognized moving faces better than static faces, prosopagnosics did not exhibit this effect. Furthermore, prosopagnosics had significantly impaired gender recognition—which is shown on a groupwise level for the first time in our study. There was no difference between groups in the automatic extraction of face identity information or in object recognition as tested with the Cambridge Car Memory Test. In addition, a methodological analysis of the tests revealed reduced reliability for holistic face processing tests in prosopagnosics. To our knowledge, this is the first study to show that prosopagnosics showed a significantly reduced reliability coefficient (Cronbach’s alpha) in the CFMT compared to the controls. We suggest that compensatory strategies employed by the prosopagnosics might be the cause for the vast variety of response patterns revealed by the reduced test reliability. This finding raises the question whether classical face tests measure the same perceptual processes in controls and prosopagnosics. PMID:27482369

Post flight system analysis of FRECOPA (AO 138)

NASA Technical Reports Server (NTRS)

Durin, Christian

1991-01-01

The unexpected duration for the flight of the Long Duration Exposure Facility (LDEF) conducted CNES to create a special investigation group in order to analyze all the materials and systems which compose the French Cooperative Payload (FRECOPA) except the experiments especially prepared for the flight. The FRECOPA tray was on the trailing face (V-) of the LDEF and protected from the atomic oxygen flux during all the flight. However, the solar irradiation was very important with solar flux quite perpendicular to the experiment once an orbit. There was also a good vacuum environment. The objectives are to test the effects of the combined space environment on materials and components like: structure, thermal control coatings and blankets, electronic unit, motors, and mechanical fixtures. When the LDEF returned to Kennedy Space Center, a visual inspection showed the very good behavior of the materials used and it was noted that the three mechanisms to open and close the experiment canisters worked completely. Many impacts of micrometeoroids or space debris on the structure and on the thermal protections were observed. After FRECOPA was brought back to Toulouse, many tests were performed and include: working order tests, mechanical tests (tension), optical and electronic microscopy (SEM), surface analysis (ESCA, SIMS, RBS, AUGER, etc.), thermal analysis, pressure measurements, and gas analysis (outgassing tests). The results of these experiments are discussed.

The Quality vs. the Quantity of Schooling: What Drives Economic Growth?

ERIC Educational Resources Information Center

Breton, Theodore R.

2011-01-01

This paper challenges Hanushek and Woessmann's (2008) contention that the quality and not the quantity of schooling determines a nation's rate of economic growth. I first show that their statistical analysis is flawed. I then show that when a nation's average test scores and average schooling attainment are included in a national income model,…

Will Choice Hurt? Compared to What? A School Choice Experiment in Estonia

ERIC Educational Resources Information Center

Põder, Kaire; Lauri, Triin

2014-01-01

This article presents the empirical analysis of the effects of a school choice policy in Estonia. The article shows that relying on markets and giving autonomy to the schools over student selection will produce admission tests, even at the elementary school level. This article's contribution is to show that a school choice policy experiment with…

Detecting Non-Gaussian and Lognormal Characteristics of Temperature and Water Vapor Mixing Ratio

NASA Astrophysics Data System (ADS)

Kliewer, A.; Fletcher, S. J.; Jones, A. S.; Forsythe, J. M.

2017-12-01

Many operational data assimilation and retrieval systems assume that the errors and variables come from a Gaussian distribution. This study builds upon previous results that shows that positive definite variables, specifically water vapor mixing ratio and temperature, can follow a non-Gaussian distribution and moreover a lognormal distribution. Previously, statistical testing procedures which included the Jarque-Bera test, the Shapiro-Wilk test, the Chi-squared goodness-of-fit test, and a composite test which incorporated the results of the former tests were employed to determine locations and time spans where atmospheric variables assume a non-Gaussian distribution. These tests are now investigated in a "sliding window" fashion in order to extend the testing procedure to near real-time. The analyzed 1-degree resolution data comes from the National Oceanic and Atmospheric Administration (NOAA) Global Forecast System (GFS) six hour forecast from the 0Z analysis. These results indicate the necessity of a Data Assimilation (DA) system to be able to properly use the lognormally-distributed variables in an appropriate Bayesian analysis that does not assume the variables are Gaussian.

Off-road motorbike performance analysis using a rear semi-active suspension

NASA Astrophysics Data System (ADS)

Lozoya-Santos, Jorge de J.; Cervantes-Muñoz, Damián.; Ramírez Mendoza, Ricardo

2015-04-01

The topic of this paper is the analysis of a control system for a semi active rear suspension in an off-road 2-wheel vehicle. Several control methods are studied, as well as the recently proposed Frequency Estimation Based (FEB) algorithm. The test motorcycle dynamics, as well as the passive, semi active, and the algorithm controlled shock absorber models are loaded into BikeSim, a professional two-wheeled vehicle simulation software, and tested in several road conditions. The results show a detailed comparison of the theoretical performance of the different control approaches in a novel environment for semi active dampers.

Integrated Data Collection Analysis (IDCA) Program - Statistical Analysis of RDX Standard Data Sets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandstrom, Mary M.; Brown, Geoffrey W.; Preston, Daniel N.

2015-10-30

The Integrated Data Collection Analysis (IDCA) program is conducting a Proficiency Test for Small- Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are statistical analyses of the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of the RDX Type II Class 5 standard. The material was tested as a well-characterized standard several times during the proficiency study to assess differences among participants and the range of results that may arise for well-behaved explosive materials. The analyses show that there are detectable differences among the results from IDCA participants. While these differences are statisticallymore » significant, most of them can be disregarded for comparison purposes to assess potential variability when laboratories attempt to measure identical samples using methods assumed to be nominally the same. The results presented in this report include the average sensitivity results for the IDCA participants and the ranges of values obtained. The ranges represent variation about the mean values of the tests of between 26% and 42%. The magnitude of this variation is attributed to differences in operator, method, and environment as well as the use of different instruments that are also of varying age. The results appear to be a good representation of the broader safety testing community based on the range of methods, instruments, and environments included in the IDCA Proficiency Test.« less

Engineering the Future: Cell 6

NASA Technical Reports Server (NTRS)

Stahl, P. H.

2010-01-01

This slide presentation reviews the development of the James Webb Space Telescope (JWST), explaining the development using a systems engineering methodology. Included are slides showing the organizational chart, the JWST Science Goals, the size of the primary mirror, and full scale mockups of the JSWT. Also included is a review of the JWST Optical Telescope Requirements, a review of the preliminary design and analysis, the technology development required to create the JWST, with particular interest in the specific mirror technology that was required, and views of the mirror manufacturing process. Several slides review the process of verification and validation by testing and analysis, including a diagram of the Cryogenic Test Facility at Marshall, and views of the primary mirror while being tested in the cryogenic facility.

Preparation of TiO2-ZnO and its activity test in sonophotocatalytic degradation of phenol

NASA Astrophysics Data System (ADS)

Fatimah, Is; Novitasari

2016-02-01

Synthesis of TiO2-ZnO and its activity test in Sono photocatalysis degradation of phenol has been conducted. The synthesis was performed by the sol-gel mechanism by using titanium isopropoxide and zinc acetate as precursors with the Ti: Zn ratio of 5:1. Characterization of material were conducted by x-ray diffraction analysis, surface area analysis and also diffuse reflectance UV-Visible spectrophotometry. The material obtained from the synthesis was tested in photocatalysis, Sono catalysis and Sono photocatalysis degradation of phenol solution. Results showed that material exhibited the activity of varied mechanism o- phenol degradation. In advance, the Sono photocatalysis degradation produced the synergy index of 1.169 compared to both photocatalysis and Sono catalysis.

Measurement and analysis of acoustic flight test data for two advanced design high speed propeller models

NASA Technical Reports Server (NTRS)

Brooks, B. M.; Mackall, K. G.

1984-01-01

The recent test program, in which the SR-2 and SR-3 Prop-Fan models were acoustically tested in flight, is described and the results of analysis of noise data acquired are discussed. The trends of noise levels with flight operating parameters are shown. The acoustic benefits of the SR-3 design with swept blades relative to the SR-2 design with straight blades are shown. Noise data measured on the surface of a small-diameter microphone boom mounted above the fuselage and on the surface of the airplane fuselage are compared to show the effects of acoustic propagation through a boundary layer. Noise level estimates made using a theoretically based prediction methodology are compared with measurements.

Integral criteria for large-scale multiple fingerprint solutions

NASA Astrophysics Data System (ADS)

Ushmaev, Oleg S.; Novikov, Sergey O.

2004-08-01

We propose the definition and analysis of the optimal integral similarity score criterion for large scale multmodal civil ID systems. Firstly, the general properties of score distributions for genuine and impostor matches for different systems and input devices are investigated. The empirical statistics was taken from the real biometric tests. Then we carry out the analysis of simultaneous score distributions for a number of combined biometric tests and primary for ultiple fingerprint solutions. The explicit and approximate relations for optimal integral score, which provides the least value of the FRR while the FAR is predefined, have been obtained. The results of real multiple fingerprint test show good correspondence with the theoretical results in the wide range of the False Acceptance and the False Rejection Rates.

Application of Optical Coherence Tomography and Contrast Sensitivity Test for Observing Fundus Changes of Patients With Pregnancy-Induced Hypertension Syndrome

PubMed Central

Wang, Zhixue; Zou, Yuanyuan; Li, Wenying; Wang, Xueyan; Zhang, Min; Wang, Wenying

2015-01-01

Abstract This study was aimed to investigate the fundus changes of patients with pregnancy-induced hypertension syndrome (PIHS) using optical coherence tomography (OCT) technology and contrast sensitivity (CS) tests. Ninety-eight patients with PIHS underwent routine eye examinations including vision correction, fundus examination, OCT, and CS tests. The CS test was performed at low, medium, and high frequency, respectively. Moreover, the difference in CS tests between 2 groups was analyzed by independent-samples T test. The Kruskal–Wallis rank sum test and linear regression model were used to detect the correlation of OCT with CS, respectively. Meanwhile Satterthwaite approximate T test was adopted for pairwise comparisons after nonparametric analysis of variance. The OCT test revealed that 56.76% of the examined eyes showed shallow retinal detachment in the macula lutea and around the optic disk. The differences in CS at each spatial frequency between the case and control group were statistically significant (P < 0.01). Besides, OCT manifestations were associated with CS at each spacial frequency including 1.5, 3, 6, 12, and 18 frequency (P < 0.01). And patients with abnormal manifestations of OCT showed lower CS at each spacial frequency than those without abnormal OCT manifestations. What's more the OCT manifestation 1 showed the greatest impact on CS at each spacial frequency. The results showed that abnormal OCT manifestations were correlated with CS in PIHS. OCT and CS tests might be valuable methods in observing fundus changes for PIHS patients. PMID:26554764

[Analysis on willingness to pay for HIV antibody saliva rapid test and related factors].

PubMed

Li, Junjie; Huo, Junli; Cui, Wenqing; Zhang, Xiujie; Hu, Yi; Su, Xingfang; Zhang, Wanyue; Li, Youfang; Shi, Yuhua; Jia, Manhong

2015-02-01

To understand the willingness to pay for HIV antibody saliva rapid test and its influential factors among people seeking counsel and HIV test, STD clinic patients, university students, migrant people, female sex workers (FSWs), men who have sex with men (MSM) and injecting drug users (IDUs). An anonymous questionnaire survey was conducted among 511 subjects in the 7 groups selected by different sampling methods, and 509 valid questionnaires were collected. The majority of subjects were males (54.8%) and aged 20-29 years (41.5%). Among the subjects, 60.3% had education level of high school or above, 55.4% were unmarried, 37.3% were unemployed, 73.3% had monthly expenditure <2 000 Yuan RMB, 44.2% had received HIV test, 28.3% knew HIV saliva test, 21.0% were willing to receive HIV saliva test, 2.0% had received HIV saliva test, only 1.0% had bought HIV test kit for self-test, and 84.1% were willing to pay for HIV antibody saliva rapid test. Univariate logistic regression analysis indicated that subject group, age, education level, employment status, monthly expenditure level, HIV test experience and willingness to receive HIV saliva test were correlated statistically with willingness to pay for HIV antibody saliva rapid test. Multivariate logistic regression analysis showed that subject group and monthly expenditure level were statistically correlated with willingness to pay for HIV antibody saliva rapid test. The willingness to pay for HIV antibody saliva rapid test and acceptable price of HIV antibody saliva rapid test varied in different areas and populations. Different populations may have different willingness to pay for HIV antibody saliva rapid test;the affordability of the test could influence the willingness to pay for the test.

Multicenter external validation of two malignancy risk prediction models in patients undergoing 18F-FDG-PET for solitary pulmonary nodule evaluation.

PubMed

Perandini, Simone; Soardi, G A; Larici, A R; Del Ciello, A; Rizzardi, G; Solazzo, A; Mancino, L; Zeraj, F; Bernhart, M; Signorini, M; Motton, M; Montemezzi, S

2017-05-01

To achieve multicentre external validation of the Herder and Bayesian Inference Malignancy Calculator (BIMC) models. Two hundred and fifty-nine solitary pulmonary nodules (SPNs) collected from four major hospitals which underwent 18-FDG-PET characterization were included in this multicentre retrospective study. The Herder model was tested on all available lesions (group A). A subgroup of 180 SPNs (group B) was used to provide unbiased comparison between the Herder and BIMC models. Receiver operating characteristic (ROC) area under the curve (AUC) analysis was performed to assess diagnostic accuracy. Decision analysis was performed by adopting the risk threshold stated in British Thoracic Society (BTS) guidelines. Unbiased comparison performed In Group B showed a ROC AUC for the Herder model of 0.807 (95 % CI 0.742-0.862) and for the BIMC model of 0.822 (95 % CI 0.758-0.875). Both the Herder and the BIMC models were proven to accurately predict the risk of malignancy when tested on a large multicentre external case series. The BIMC model seems advantageous on the basis of a more favourable decision analysis. • The Herder model showed a ROC AUC of 0.807 on 180 SPNs. • The BIMC model showed a ROC AUC of 0.822 on 180 SPNs. • Decision analysis is more favourable to the BIMC model.

Analysis of the psychometric properties of the American Orthopaedic Foot and Ankle Society Score (AOFAS) in rheumatoid arthritis patients: application of the Rasch model.

PubMed

Conceição, Cristiano Sena da; Neto, Mansueto Gomes; Neto, Anolino Costa; Mendes, Selena M D; Baptista, Abrahão Fontes; Sá, Kátia Nunes

2016-01-01

To tested the reliability and validity of Aofas in a sample of rheumatoid arthritis patients. The scale was applicable to rheumatoid arthritis patients, twice by the interviewer 1 and once by the interviewer 2. The Aofas was subjected to test-retest reliability analysis (with 20 Rheumatoid arthritis subjects). The psychometric properties were investigated using Rasch analysis on 33 Rheumatoid arthritis patients. Intra-Class Correlation Coefficient (ICC) were (0.90

Neutral polymorphisms in putative housekeeping genes and tandem repeats unravels the population genetics and evolutionary history of Plasmodium vivax in India.

PubMed

Prajapati, Surendra K; Joshi, Hema; Carlton, Jane M; Rizvi, M Alam

2013-01-01

The evolutionary history and age of Plasmodium vivax has been inferred as both recent and ancient by several studies, mainly using mitochondrial genome diversity. Here we address the age of P. vivax on the Indian subcontinent using selectively neutral housekeeping genes and tandem repeat loci. Analysis of ten housekeeping genes revealed a substantial number of SNPs (n = 75) from 100 P. vivax isolates collected from five geographical regions of India. Neutrality tests showed a majority of the housekeeping genes were selectively neutral, confirming the suitability of housekeeping genes for inferring the evolutionary history of P. vivax. In addition, a genetic differentiation test using housekeeping gene polymorphism data showed a lack of geographical structuring between the five regions of India. The coalescence analysis of the time to the most recent common ancestor estimate yielded an ancient TMRCA (232,228 to 303,030 years) and long-term population history (79,235 to 104,008) of extant P. vivax on the Indian subcontinent. Analysis of 18 tandem repeat loci polymorphisms showed substantial allelic diversity and heterozygosity per locus, and analysis of potential bottlenecks revealed the signature of a stable P. vivax population, further corroborating our ancient age estimates. For the first time we report a comparable evolutionary history of P. vivax inferred by nuclear genetic markers (putative housekeeping genes) to that inferred from mitochondrial genome diversity.

Comparison of two computer codes for crack growth analysis: NASCRAC Versus NASA/FLAGRO

NASA Technical Reports Server (NTRS)

Stallworth, R.; Meyers, C. A.; Stinson, H. C.

1989-01-01

Results are presented from the comparison study of two computer codes for crack growth analysis - NASCRAC and NASA/FLAGRO. The two computer codes gave compatible conservative results when the part through crack analysis solutions were analyzed versus experimental test data. Results showed good correlation between the codes for the through crack at a lug solution. For the through crack at a lug solution, NASA/FLAGRO gave the most conservative results.

Inter-vender and test-retest reliabilities of resting-state functional magnetic resonance imaging: Implications for multi-center imaging studies.

PubMed

An, Hyeong Su; Moon, Won-Jin; Ryu, Jae-Kyun; Park, Ju Yeon; Yun, Won Sung; Choi, Jin Woo; Jahng, Geon-Ho; Park, Jang-Yeon

2017-12-01

This prospective multi-center study aimed to evaluate the inter-vendor and test-retest reliabilities of resting-state functional magnetic resonance imaging (RS-fMRI) by assessing the temporal signal-to-noise ratio (tSNR) and functional connectivity. Study included 10 healthy subjects and each subject was scanned using three 3T MR scanners (GE Signa HDxt, Siemens Skyra, and Philips Achieva) in two sessions. The tSNR was calculated from the time course data. Inter-vendor and test-retest reliabilities were assessed with intra-class correlation coefficients (ICCs) derived from variant component analysis. Independent component analysis was performed to identify the connectivity of the default-mode network (DMN). In result, the tSNR for the DMN was not significantly different among the GE, Philips, and Siemens scanners (P=0.638). In terms of vendor differences, the inter-vendor reliability was good (ICC=0.774). Regarding the test-retest reliability, the GE scanner showed excellent correlation (ICC=0.961), while the Philips (ICC=0.671) and Siemens (ICC=0.726) scanners showed relatively good correlation. The DMN pattern of the subjects between the two sessions for each scanner and between three scanners showed the identical patterns of functional connectivity. The inter-vendor and test-retest reliabilities of RS-fMRI using different 3T MR scanners are good. Thus, we suggest that RS-fMRI could be used in multicenter imaging studies as a reliable imaging marker. Copyright © 2017 Elsevier Inc. All rights reserved.

Effect of open rhinoplasty on the smile line.

PubMed

Tabrizi, Reza; Mirmohamadsadeghi, Hoori; Daneshjoo, Danadokht; Zare, Samira

2012-05-01

Open rhinoplasty is an esthetic surgical technique that is becoming increasingly popular, and can affect the nose and upper lip compartments. The aim of this study was to evaluate the effect of open rhinoplasty on tooth show and the smile line. The study participants were 61 patients with a mean age of 24.3 years (range, 17.2 to 39.6 years). The surgical procedure consisted of an esthetic open rhinoplasty without alar resection. Analysis of tooth show was limited to pre- and postoperative (at 12 months) tooth show measurements at rest and the maximum smile with a ruler (when participants held their heads naturally). Statistical analyses were performed with SPSS 13.0, and paired-sample t tests were used to compare tooth show means before and after the operation. Analysis of the rest position showed no statistically significant change in tooth show (P = .15), but analysis of participants' maximum smile data showed a statistically significant increase in tooth show after surgery (P < .05). In contrast, Pearson correlation analysis showed a positive relation between rhinoplasty and tooth show increases in maximum smile, especially in subjects with high smile lines. This study shows that the nasolabial compartment is a single unit and any change in 1 part may influence the other parts. Further studies should be conducted to investigate these interactions. Copyright © 2012 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

A need for a standardization in anaerobic digestion experiments? Let's get some insight from meta-analysis and multivariate analysis.

PubMed

Lavergne, Céline; Jeison, David; Ortega, Valentina; Chamy, Rolando; Donoso-Bravo, Andrés

2018-09-15

An important variability in the experimental results in anaerobic digestion lab test has been reported. This study presents a meta-analysis coupled with multivariate analysis aiming to assess the impact of this experimental variability in batch and continuous operation at mesophilic and thermophilic anaerobic digestion of waste activated sludge. An analysis of variance showed that there was no significant difference between mesophilic and thermophilic conditions in both continuous and batch conditions. Concerning the operation mode, the values of methane yield were significantly higher in batch experiment than in continuous reactors. According to the PCA, for both cases, the methane yield is positive correlated to the temperature rises. Interestingly, in the batch experiments, the higher the volatile solids in the substrate was, the lowest was the methane production, which is correlated to experimental flaws when setting up those tests. In continuous mode, unlike the batch test, the methane yield is strongly (positively) correlated to the organic content of the substrate. Experimental standardization, above all, in batch conditions are urgently necessary or move to continuous experiments for reporting results. The modeling can also be a source of disturbance in batch test. Copyright © 2018 Elsevier Ltd. All rights reserved.

Detrended Partial-Cross-Correlation Analysis: A New Method for Analyzing Correlations in Complex System

PubMed Central

Yuan, Naiming; Fu, Zuntao; Zhang, Huan; Piao, Lin; Xoplaki, Elena; Luterbacher, Juerg

2015-01-01

In this paper, a new method, detrended partial-cross-correlation analysis (DPCCA), is proposed. Based on detrended cross-correlation analysis (DCCA), this method is improved by including partial-correlation technique, which can be applied to quantify the relations of two non-stationary signals (with influences of other signals removed) on different time scales. We illustrate the advantages of this method by performing two numerical tests. Test I shows the advantages of DPCCA in handling non-stationary signals, while Test II reveals the “intrinsic” relations between two considered time series with potential influences of other unconsidered signals removed. To further show the utility of DPCCA in natural complex systems, we provide new evidence on the winter-time Pacific Decadal Oscillation (PDO) and the winter-time Nino3 Sea Surface Temperature Anomaly (Nino3-SSTA) affecting the Summer Rainfall over the middle-lower reaches of the Yangtze River (SRYR). By applying DPCCA, better significant correlations between SRYR and Nino3-SSTA on time scales of 6 ~ 8 years are found over the period 1951 ~ 2012, while significant correlations between SRYR and PDO on time scales of 35 years arise. With these physically explainable results, we have confidence that DPCCA is an useful method in addressing complex systems. PMID:25634341

Nucleotide sequence analysis of a DNA region involved in capsular polysaccharide biosynthesis reveals the molecular basis of the nontypeability of two Actinobacillus pleuropneumoniae isolates.

PubMed

Ito, Hiroya; Ogawa, Torata; Fukamizu, Dai; Morinaga, Yuiko; Kusumoto, Masahiro

2016-11-01

The aim of our study was to reveal the molecular basis of the serologic nontypeability of 2 Actinobacillus pleuropneumoniae field isolates. Nine field strains of A. pleuropneumoniae, the causative agent of porcine pleuropneumonia, were isolated from pigs raised on the same farm and sent to our diagnostic laboratory for serotyping. Seven of the 9 strains were identified as serovar 15 strains by immunodiffusion tests. However, 2 strains, designated FH24-2 and FH24-5, could not be serotyped with antiserum prepared against serovars 1-15. Strain FH24-5 showed positive results in 2 serovar 15-specific PCR tests, whereas strain FH24-2 was only positive in 1 of the 2 PCR tests. The nucleotide sequence analysis of gene clusters involved in capsular polysaccharide biosynthesis of the 2 nontypeable strains revealed that both had been rendered nontypeable by the action of ISApl1, a transposable element of A. pleuropneumoniae belonging to the IS30 family. The results showed that ISApl1 of A. pleuropneumoniae can interfere with both the serologic and molecular typing methods, and that nucleotide sequence analysis across the capsular gene clusters is the best means of determining the cause of serologic nontypeability in A. pleuropneumoniae. © 2016 The Author(s).