Investigation of Conditions of Titanium Carbonization - IV

NASA Technical Reports Server (NTRS)

Meerson, G. A.; Lipkes, Y. M.

1949-01-01

In a previous paper, results are presented of accurate investigations of the processes of titanium carbonization and the succeeding titanium carbide decarbonization as related to the phenomenon of the graphitization of soot by heating at a constant temperature in atmospheres of pure hydrogen and carbon monoxide. These tests showed that the processes of titanium carbonization-decarbonization in an atmosphere of pure gases without nitrogen proceed in the same direction as the analogous processes under the conditions of the production furnace. In this case, however, the presence of admixtures of nitrogen changes the quantitative results of the decarbonization process. Thermodynamic computations confirming the results of previous tests conducted at atmospheric pressure and additional tests of titanium carbonization at lowered pressures are presented herein.

Effect of using a treadmill workstation on performance of simulated office work tasks.

PubMed

John, Dinesh; Bassett, David; Thompson, Dixie; Fairbrother, Jeffrey; Baldwin, Debora

2009-09-01

Although using a treadmill workstation may change the sedentary nature of desk jobs, it is unknown if walking while working affects performance on office-work related tasks. To assess differences between seated and walking conditions on motor skills and cognitive function tests. Eleven males (24.6 +/- 3.5 y) and 9 females (27.0 +/- 3.9 y) completed a test battery to assess selective attention and processing speed, typing speed, mouse clicking/drag-and-drop speed, and GRE math and reading comprehension. Testing was performed under seated and walking conditions on 2 separate days using a counterbalanced, within subjects design. Participants did not have an acclimation period before the walking condition. Paired t tests (P < .05) revealed that in the seated condition, completion times were shorter for mouse clicking (26.6 +/- 3.0 vs. 28.2 +/- 2.5s) and drag-and-drop (40.3 +/- 4.2 vs. 43.9 +/- 2.5s) tests, typing speed was greater (40.2 +/- 9.1 vs. 36.9 +/- 10.2 adjusted words x min(-1)), and math scores were better (71.4 +/- 15.2 vs. 64.3 +/- 13.4%). There were no significant differences between conditions in selective attention and processing speed or in reading comprehension. Compared with the seated condition, treadmill walking caused a 6% to 11% decrease in measures of fine motor skills and math problem solving, but did not affect selective attention and processing speed or reading comprehension.

Use of adaptive walls in 2D tests

NASA Technical Reports Server (NTRS)

Archambaud, J. P.; Chevallier, J. P.

1984-01-01

A new method for computing the wall effects gives precise answers to some questions arising in adaptive wall concept applications: length of adapted regions, fairings with up and downstream regions, residual misadjustments effects, reference conditions. The acceleration of the iterative process convergence and the development of an efficient technology used in CERT T2 wind tunnels give in a single run the required test conditions. Samples taken from CAST 7 tests demonstrate the efficiency of the whole process to obtain significant results with considerations of tridimensional case extension.

One-year-old fear memories rapidly activate human fusiform gyrus

PubMed Central

Pizzagalli, Diego A.

2016-01-01

Fast threat detection is crucial for survival. In line with such evolutionary pressure, threat-signaling fear-conditioned faces have been found to rapidly (<80 ms) activate visual brain regions including the fusiform gyrus on the conditioning day. Whether remotely fear conditioned stimuli (CS) evoke similar early processing enhancements is unknown. Here, 16 participants who underwent a differential face fear-conditioning and extinction procedure on day 1 were presented the initial CS 24 h after conditioning (Recent Recall Test) as well as 9-17 months later (Remote Recall Test) while EEG was recorded. Using a data-driven segmentation procedure of CS evoked event-related potentials, five distinct microstates were identified for both the recent and the remote memory test. To probe intracranial activity, EEG activity within each microstate was localized using low resolution electromagnetic tomography analysis (LORETA). In both the recent (41–55 and 150–191 ms) and remote (45–90 ms) recall tests, fear conditioned faces potentiated rapid activation in proximity of fusiform gyrus, even in participants unaware of the contingencies. These findings suggest that rapid processing enhancements of conditioned faces persist over time. PMID:26416784

High density electronic circuit and process for making

DOEpatents

Morgan, William P.

1999-01-01

High density circuits with posts that protrude beyond one surface of a substrate to provide easy mounting of devices such as integrated circuits. The posts also provide stress relief to accommodate differential thermal expansion. The process allows high interconnect density with fewer alignment restrictions and less wasted circuit area than previous processes. The resulting substrates can be test platforms for die testing and for multi-chip module substrate testing. The test platform can contain active components and emulate realistic operational conditions, replacing shorts/opens net testing.

Compressive behavior of laminated neoprene bridge bearing pads under thermal aging condition

NASA Astrophysics Data System (ADS)

Jun, Xie; Zhang, Yannian; Shan, Chunhong

2017-10-01

The present study was conducted to obtain a better understanding of the variation rule of mechanical properties of laminated neoprene bridge bearing pads under thermal aging condition using compression tests. A total of 5 specimens were processed in a high-temperature chamber. After that, the specimens were tested subjected to axial load. The parameter mainly considered time of thermal aging processing for specimens. The results of compression tests show that the specimens after thermal aging processing are more probably brittle failure than the standard specimen. Moreover, the exposure of steel plate, cracks and other failure phenomena are more serious than the standard specimen. The compressive capacity, ultimate compressive strength, compressive elastic modulus of the laminated neoprene bridge bearing pads decreased dramatically with the increasing in the aging time of thermal aging processing. The attenuation trends of ultimate compressive strength, compressive elastic modulus of laminated neoprene bridge bearing pads under thermal aging condition accord with power function. The attenuation models are acquired by regressing data of experiment with the least square method. The attenuation models conform to reality well which shows that this model is applicable and has vast prospect in assessing the performance of laminated neoprene bridge bearing pads under thermal aging condition.

Robustness testing in pharmaceutical freeze-drying: inter-relation of process conditions and product quality attributes studied for a vaccine formulation.

PubMed

Schneid, Stefan C; Stärtzel, Peter M; Lettner, Patrick; Gieseler, Henning

2011-01-01

The recent US Food and Drug Administration (FDA) legislation has introduced the evaluation of the Design Space of critical process parameters in manufacturing processes. In freeze-drying, a "formulation" is expected to be robust when minor deviations of the product temperature do not negatively affect the final product quality attributes. To evaluate "formulation" robustness by investigating the effect of elevated product temperature on product quality using a bacterial vaccine solution. The vaccine solution was characterized by freeze-dry microscopy to determine the critical formulation temperature. A conservative cycle was developed using the SMART™ mode of a Lyostar II freeze dryer. Product temperature was elevated to imitate intermediate and aggressive cycle conditions. The final product was analyzed using X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), Karl Fischer, and modulated differential scanning calorimetry (MDSC), and the life cell count (LCC) during accelerated stability testing. The cakes processed at intermediate and aggressive conditions displayed larger pores with microcollapse of walls and stronger loss in LCC than the conservatively processed product, especially during stability testing. For all process conditions, a loss of the majority of cells was observed during storage. For freeze-drying of life bacterial vaccine solutions, the product temperature profile during primary drying appeared to be inter-related to product quality attributes.

Alloy 690 qualification: Corrosion under prototypic heat flux and temperature conditions. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baum, A.J.

1995-05-01

The objective of this program was to perform qualification tests of industrial heats of thermally treated alloy 690 steam generator tubing under heat transfer conditions. Primary emphasis was focused on testing of alternate tube to tubesheet expansion processes. In addition, a background report was written to document the evolution of the alloy 690 process specification and the supporting qualification testing. While the testing was able to produce some localized corrosion of alloy 690 in the tube to tubesheet joint transition regions under highly alkaline conditions, the corrosion rates were between two and three orders of magnitude lower than the comparablemore » rates in mill annealed alloy 600 tubing. The corrosion morphology was a combination of intergranular and general corrosion, rather than the stress corrosion cracking typically found in mill annealed alloy 600 tubing.« less

Evaluation of 20 Ah Li Ion Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Ratnakumar, B. V.; Huang, Charles K.; Surampudi, S.; Hill, Carole; Radzykewycz, Dan T.; Marsh, Richard A.

1998-01-01

Lithium ion cells of 20 Ah capacity were fabricated by Bluestar Advanced Technology Corporation, Canada under a developmental contract from US Air Force. In this paper, we report our studies on the evaluation of these cells under various test conditions. These include generic test conditions such as discharges and charges at different temperatures to understand the rate-limiting processes in the discharge/charge processes as a function of temperature, and cycle life under standard cycling conditions (100% DOD) at ambient temperature. In addition, tests are being done to ascertain the performance of the cells in the Mars 2001 Lander application, which includes pulse testing of the cells at 60 A and 40 A loads for 100 mS and 1 min., respectively at different states of charge and temperatures, and cycling at low temperature at partial depths of discharge.

Hanford spent nuclear fuel hot conditioning system test procedure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleveland, K.J.

1997-09-16

This document provides the test procedures for cold testing of the prototype Hot Conditioning System (HCS) at the 306E Facility. The primary objective of this testing is to confirm design choices and provide data for the detailed design package prior to procurement of the process equipment. The current scope of testing in this document includes a fabricability study of the HCS, equipment performance testing of the HCS components, heat-up and cool-down cycle simulation, and robotic arm testing.

Transient, hypervelocity flow in an axisymmetric nozzle

NASA Technical Reports Server (NTRS)

Jacobs, P. A.

1991-01-01

The performance of an axisymmetric nozzle was examined which was designed to produce uniform, parallel flow with a nominal Mach number of 8. A free-piston driven shock tube was used to supply the nozzle with high-temperature, high-pressure test gas. Performance was assessed by measuring Pitot pressures across the exit plane of the nozzle and, over the range of operating conditions examined, the nozzle produced satisfactory test flows. However, there were flow disturbances that persisted for significant times after flow initiation. The detailed starting process of the nozzle was also investigated by performing numerical simulations at several nominal test conditions. The classical description of the starting process, based on a quasi-one-dimensional model, provided a reasonable approximation and was used to demonstrate that the starting process could consume a significant fraction of the otherwise usable test gas. This was especially important at high operating enthalpies where nozzle supply conditions were maintained for shorter times. Multidimensional simulations illustrated a mechanism by which the starting process in the actual nozzle could take longer than that predicted by the quasi-one-dimensional analysis. However, the cause of the persistent disturbances observed in the experimental calibration was not identified.

Pyrotechnic hazards classification and evaluation program. Phase 2, segment 3: Test plan for determining hazards associated with pyrotechnic manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

A comprehensive test plan for determining the hazards associated with pyrotechnic manufacturing processes is presented. The rationale for each test is based on a systematic analysis of historical accounts of accidents and a detailed study of the characteristics of each manufacturing process. The most hazardous manufacturing operations have been determined to be pressing, mixing, reaming, and filling. The hazard potential of a given situation is evaluated in terms of the probabilities of initiation, communication, and transition to detonation (ICT). The characteristics which affect the ICT probabilities include the ignition mechanisms which are present either in normal or abnormal operation, the condition and properties of the pyrotechnic material, and the configuration of the processing equipment. Analytic expressions are derived which describe the physical conditions of the system, thus permitting a variety of processes to be evaluated in terms of a small number of experiments.

Subliminal influence on preferences? A test of evaluative conditioning for brief visual conditioned stimuli using auditory unconditioned stimuli

PubMed Central

2017-01-01

In the field of evaluative conditioning (EC), two opposing theories—propositional single-process theory versus dual-process theory—are currently being discussed in the literature. The present set of experiments test a crucial prediction to adjudicate between these two theories: Dual-process theory postulates that evaluative conditioning can occur without awareness of the contingency between conditioned stimulus (CS) and unconditioned stimulus (US); in contrast, single-process propositional theory postulates that EC requires CS-US contingency awareness. In a set of three studies, we experimentally manipulate contingency awareness by presenting the CSs very briefly, thereby rendering it unlikely to be processed consciously. We address potential issues with previous studies on EC with subliminal or near-threshold CSs that limited their interpretation. Across two experiments, we consistently found an EC effect for CSs presented for 1000 ms and consistently failed to find an EC effect for briefly presented CSs. In a third pre-registered experiment, we again found evidence for an EC effect with CSs presented for 1000 ms, and we found some indication for an EC effect for CSs presented for 20 ms. PMID:28989730

Subliminal influence on preferences? A test of evaluative conditioning for brief visual conditioned stimuli using auditory unconditioned stimuli.

PubMed

Heycke, Tobias; Aust, Frederik; Stahl, Christoph

2017-09-01

In the field of evaluative conditioning (EC), two opposing theories-propositional single-process theory versus dual-process theory-are currently being discussed in the literature. The present set of experiments test a crucial prediction to adjudicate between these two theories: Dual-process theory postulates that evaluative conditioning can occur without awareness of the contingency between conditioned stimulus (CS) and unconditioned stimulus (US); in contrast, single-process propositional theory postulates that EC requires CS-US contingency awareness. In a set of three studies, we experimentally manipulate contingency awareness by presenting the CSs very briefly, thereby rendering it unlikely to be processed consciously. We address potential issues with previous studies on EC with subliminal or near-threshold CSs that limited their interpretation. Across two experiments, we consistently found an EC effect for CSs presented for 1000 ms and consistently failed to find an EC effect for briefly presented CSs. In a third pre-registered experiment, we again found evidence for an EC effect with CSs presented for 1000 ms, and we found some indication for an EC effect for CSs presented for 20 ms.

Detection of Subsurface Defects in Levees in Correlation to Weather Conditions Utilizing Ground Penetrating Radar

NASA Astrophysics Data System (ADS)

Martinez, I. A.; Eisenmann, D.

2012-12-01

Ground Penetrating Radar (GPR) has been used for many years in successful subsurface detection of conductive and non-conductive objects in all types of material including different soils and concrete. Typical defect detection is based on subjective examination of processed scans using data collection and analysis software to acquire and analyze the data, often requiring a developed expertise or an awareness of how a GPR works while collecting data. Processing programs, such as GSSI's RADAN analysis software are then used to validate the collected information. Iowa State University's Center for Nondestructive Evaluation (CNDE) has built a test site, resembling a typical levee used near rivers, which contains known sub-surface targets of varying size, depth, and conductivity. Scientist at CNDE have developed software with the enhanced capabilities, to decipher a hyperbola's magnitude and amplitude for GPR signal processing. With this enhanced capability, the signal processing and defect detection capabilities for GPR have the potential to be greatly enhanced. This study will examine the effects of test parameters, antenna frequency (400MHz), data manipulation methods (which include data filters and restricting the range of depth in which the chosen antenna's signal can reach), and real-world conditions using this test site (such as varying weather conditions) , with the goal of improving GPR tests sensitivity for differing soil conditions.

Refractory Wear Mechanisms in the Nonferrous Metal Industry: Testing and Modeling Results

NASA Astrophysics Data System (ADS)

Gregurek, D.; Ressler, A.; Reiter, V.; Franzkowiak, A.; Spanring, A.; Prietl, T.

2013-11-01

Nonferrous pyrometallurgical processes today operate at a high intensity requiring the best standards for the furnace refractory systems. From one plant to another, there is a range of process conditions such as temperature, slag chemistry, and feed types, and each of these parameters can influence refractory life. It is generally understood that process changes at plants can impact refractory life. The ability to test and understand refractory responses to a wide range of furnace operating conditions is therefore important. The RHI Technology Centre in Leoben, Austria is well equipped with laboratory and pilot plant facilities to evaluate refractory suitability over the range of conditions encountered in modern nonferrous pyrometallurgical systems. This article describes refractory testing at the RHI Technology Centre of the impact of two metallurgical slags on a number of different RHI test bricks. The slags were a fayalite slag and a calcium ferrite slag supplied by two smelter plants. High-temperature corrosion tests were carried out in a 250-mm-diameter induction furnace and a 165-mm-diameter short rotary kiln; each unit was lined with a number of refractory bricks and tested against attack by the particular slag. After testing, the refractory bricks were subjected to several laboratory tests to determine the extent of corrosion. Optimal refractory choices for the customers' plants were developed based on the test results.

Interface conditions of two-shot molded parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kisslinger, Thomas, E-mail: thomas.kisslinger@pccl.at; Bruckmoser, Katharina, E-mail: katharina.bruckmoser@unileoben.ac.at; Resch, Katharina, E-mail: katharina.resch@unileoben.ac.at

2014-05-15

The focus of this work is on interfaces of two-shot molded parts. It is well known that e.g. material combination, process parameters and contact area structures show significant effects on the bond strength of multi-component injection molded parts. To get information about the bond strength at various process parameter settings and material combinations a test mold with core back technology was used to produce two-component injection molded tensile test specimens. At the core back process the different materials are injected consecutively, so each component runs through the whole injection molding cycle (two-shot process). Due to this consecutive injection molding processes,more » a cold interface is generated. This is defined as overmolding of a second melt to a solidified polymer preform. Strong interest lies in the way the interface conditions change during the adhesion formation between the individual components. Hence the interface conditions were investigated by computed tomography and Raman spectroscopy. By analyzing these conditions the understanding of the adhesion development during the multi-component injection molding was improved.« less

Migration Study of Butylated Hydroxytoluene and Irganox 1010 from Polypropylene Treated with Severe Processing Conditions.

PubMed

Kang, Kyungmo; Chang, Yoonjee; Choi, Jae Chun; Park, Se-Jong; Han, Jaejoon

2018-04-01

Safety concerns have emerged over the increased use of polypropylene (PP) in food-packaging markets. Some antioxidants in PP can migrate to foods and cause undesirable effects in humans. In this study, migration behaviors of butylated hydroxytoluene (BHT) and Irganox 1010 (I-1010) in PP sheets were determined according to the US FDA migration test conditions. In particular, we tested the effects of severe conditions of food processing and storage, such as autoclave heating (sterilization at about 121 °C), microwave radiation (700 W), and deep freezing (-30 °C) on migration of antioxidants. Migrant concentrations were higher in 95% ethanol as lipid food simulant, because of the hydrophobic nature of both PP and antioxidants. Autoclave heating treatment increased migrant concentrations compared with other processing conditions. Moreover, increased migrant concentrations by deep freezing condition were attributed to the brittleness of PP at freezing temperature. Regardless of processing conditions, BHT which has a lower molecular weight, migrated faster than I-1010. The antioxidants with hydrophobic nature such as butylated hydroxytoluene (BHT) and Irganox 1010 (I-1010) in polypropylene sheets would be migrated to foods, which is an important issue for industrial production food packaging materials. Migration behavior was promoted by severe processing conditions such as autoclave heating, microwave radiation, freezing, and especially autoclave heating treatment led the highest migration among them. Therefore, control of chemical additive migration from polypropylene food packaging is needed for safe food processing. © 2018 Institute of Food Technologists®.

Are awareness questionnaires valid? Investigating the use of posttest questionnaires for assessing awareness in implicit memory tests.

PubMed

Barnhardt, Terrence M; Geraci, Lisa

2008-01-01

Two experiments--one employing a perceptual implicit memory test and the other a conceptual implicit memory test--investigated the validity of posttest questionnaires for determining the incidence of awareness in implicit memory tests. In both experiments, a condition in which none of the studied words could be used as test responses (i.e., the none-studied condition) was compared with a standard implicit test condition. Results showed that reports of awareness on the posttest questionnaire were much less frequent in the none-studied condition than in the standard condition. This was especially true after deep processing at study. In both experiments, 83% of the participants in the none-studied condition stated they were unaware even though there were strong demands for claiming awareness. Although there was a small bias in the questionnaire (i.e., 17% of the participants in the none-studied condition stated they were aware), overall, there was strong support for the validity of awareness questionnaires.

High density electronic circuit and process for making

DOEpatents

Morgan, W.P.

1999-06-29

High density circuits with posts that protrude beyond one surface of a substrate to provide easy mounting of devices such as integrated circuits are disclosed. The posts also provide stress relief to accommodate differential thermal expansion. The process allows high interconnect density with fewer alignment restrictions and less wasted circuit area than previous processes. The resulting substrates can be test platforms for die testing and for multi-chip module substrate testing. The test platform can contain active components and emulate realistic operational conditions, replacing shorts/opens net testing. 8 figs.

Enhancing the placebo response: fMRI Evidence of Memory and Semantic Processing in Placebo Analgesia

PubMed Central

Craggs, Jason G.; Price, Donald D.; Robinson, Michael E.

2014-01-01

Two groups of patients with irritable bowel syndrome (IBS) rated pain and underwent fMRI brain scanning during experimentally induced rectal distension (20 sec, 7 stimuli). Group #1 was tested under baseline (natural history) and a verbally induced placebo condition, whereas Group #2 was tested under baseline, and standard placebo (no verbal suggestion for pain reduction) and intrarectal lidocaine conditions. As hypothesized, intrarectal lidocaine reduced evoked pain and pain-related brain activity within Group #2Between-group comparisons showed that adding a verbal suggestion to a placebo condition increased neural activity involved in memory and semantic processing, areas that process the placebo suggestions. These areas, in turn, are likely to influence brain areas involved in emotions and analgesia and consequently the placebo effect. These placebo suggestions also added significant decreases in activity of brain areas that process pain. The test stimulus itself seems to cue these effects and is consistent with previous explanations that somatic focus and sensory feedback reinforce expectations and other factors that mediate placebo analgesic effects. PMID:24412799

Hydrothermal Testing of K Basin Sludge and N Reactor Fuel at Sludge Treatment Project Operating Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Delegard, Calvin H.; Schmidt, Andrew J.; Thornton, Brenda M.

The Sludge Treatment Project (STP), managed for the U. S. DOE by Fluor Hanford (FH), was created to design and operate a process to eliminate uranium metal from K Basin sludge prior to packaging for Waste Isolation Pilot Plant (WIPP). The STP process uses high temperature liquid water to accelerate the reaction, produce uranium dioxide from the uranium metal, and safely discharge the hydrogen. Under nominal process conditions, the sludge will be heated in pressurized water at 185°C for as long as 72 hours to assure the complete reaction (corrosion) of up to 0.25-inch diameter uranium metal pieces. Under contractmore » to FH, the Pacific Northwest National Laboratory (PNNL) conducted bench-scale testing of the STP hydrothermal process in November and December 2006. Five tests (~50 ml each) were conducted in sealed, un-agitated reaction vessels under the hydrothermal conditions (e.g., 7 to 72 h at 185°C) of the STP corrosion process using radioactive sludge samples collected from the K East Basin and particles/coupons of N Reactor fuel also taken from the K Basins. The tests were designed to evaluate and understand the chemical changes that may be occurring and the effects that any changes would have on sludge rheological properties. The tests were not designed to evaluate engineering aspects of the process. The hydrothermal treatment affected the chemical and physical properties of the sludge. In each test, significant uranium compound phase changes were identified, resulting from dehydration and chemical reduction reactions. Physical properties of the sludge were significantly altered from their initial, as-settled sludge values, including, shear strength, settled density, weight percent water, and gas retention.« less

Testing of the BipiColombo Antenna Pointing Mechanism

NASA Astrophysics Data System (ADS)

Campo, Pablo; Barrio, Aingeru; Martin, Fernando

2015-09-01

BepiColombo is an ESA mission to Mercury, its planetary orbiter (MPO) has two antenna pointing mechanism, High gain antenna (HGA) pointing mechanism steers and points a large reflector which is integrated at system level by TAS-I Rome. Medium gain antenna (MGA) APM points a 1.5 m boom with a horn antenna. Both radiating elements are exposed to sun fluxes as high as 10 solar constants without protections.A previous paper [1] described the design and development process to solve the challenges of performing in harsh environment.. Current paper is focused on the testing process of the qualification units. Testing performance of antenna pointing mechanism in its specific environmental conditions has required special set-up and techniques. The process has provided valuable feedback on the design and the testing methods which have been included in the PFM design and tests.Some of the technologies and components were developed on dedicated items priort to EQM, but once integrated, test behaviour had relevant differences.Some of the major concerns for the APM testing are:- Create during the thermal vacuum testing the qualification temperature map with gradients along the APM. From of 200oC to 70oC.- Test in that conditions the radio frequency and pointing performances adding also high RF power to check the power handling and self-heating of the rotary joint.- Test in life up to 12000 equivalent APM revolutions, that is 14.3 million motor revolutions in different thermal conditions.- Measure low thermal distortion of the mechanical chain, being at the same time insulated from external environment and interfaces (55 arcsec pointing error)- Perform deployment of large items guaranteeing during the process low humidity, below 5% to protect dry lubrication- Verify stability with representative inertia of large boom or reflector 20 Kgm2.

Color-Word Stroop test performance across the adult life span.

PubMed

Uttl, B; Graf, P

1997-06-01

In the Color-Word Stroop test (CWST), the basic task is to name the ink color of rows of XXXs, and performance in this condition is compared with performance in naming the ink-color of color words under conditions where word meanings and ink colors mismatch or are incongruent (e.g., the word red printed in green ink). The present study investigated whether Stroop test interference, defined as the cost associated with ink-color naming in the incongruous stimulus condition versus in the basic color-naming condition, provides positive evidence for a kind of processing qualitatively different than that which is required for color naming or for word reading. Does the pattern of age-related differences in Stroop interference force the conclusion that the incongruous condition taps a qualitatively different kind of processing than that required for color naming or for word reading? We gave the CWST to 310 healthy adults. Their performance in each condition of the test replicates and extends previous findings. Structural equation modeling of the data showed a significant, direct link between age and performance in the latent factor associated with the incongruent condition. However, this direct link with age produced a relatively small increase in the model's fit; it amounted to only a .024 increase in the proportion of variance explained in the incongruent condition. In light of this small direct influence due to age, the most parsimonious explanation of our findings is that age effects in Stroop interference are due to age-related slowing (which is also indexed by color naming and by word reading) primarily; the findings do not provide evidence for a qualitatively different kind of processing that declines with age.

Neural bases of different cognitive strategies for facial affect processing in schizophrenia.

PubMed

Fakra, Eric; Salgado-Pineda, Pilar; Delaveau, Pauline; Hariri, Ahmad R; Blin, Olivier

2008-03-01

To examine the neural basis and dynamics of facial affect processing in schizophrenic patients as compared to healthy controls. Fourteen schizophrenic patients and fourteen matched controls performed a facial affect identification task during fMRI acquisition. The emotional task included an intuitive emotional condition (matching emotional faces) and a more cognitively demanding condition (labeling emotional faces). Individual analysis for each emotional condition, and second-level t-tests examining both within-, and between-group differences, were carried out using a random effects approach. Psychophysiological interactions (PPI) were tested for variations in functional connectivity between amygdala and other brain regions as a function of changes in experimental conditions (labeling versus matching). During the labeling condition, both groups engaged similar networks. During the matching condition, schizophrenics failed to activate regions of the limbic system implicated in the automatic processing of emotions. PPI revealed an inverse functional connectivity between prefrontal regions and the left amygdala in healthy volunteers but there was no such change in patients. Furthermore, during the matching condition, and compared to controls, patients showed decreased activation of regions involved in holistic face processing (fusiform gyrus) and increased activation of regions associated with feature analysis (inferior parietal cortex, left middle temporal lobe, right precuneus). Our findings suggest that schizophrenic patients invariably adopt a cognitive approach when identifying facial affect. The distributed neocortical network observed during the intuitive condition indicates that patients may resort to feature-based, rather than configuration-based, processing and may constitute a compensatory strategy for limbic dysfunction.

Hyper-X Stage Separation Wind Tunnel Test Program

NASA Technical Reports Server (NTRS)

Woods, W. C.; Holland, S. D.; DiFulvio, M.

2000-01-01

NASA's Hyper-X research program was developed primarily to flight demonstrate a supersonic combustion ramjet engine, fully integrated with a forebody designed to tailor inlet flow conditions and a free expansion nozzle/afterbody to produce positive thrust at design flight conditions. With a point-designed propulsion system, the vehicle must depend upon some other means for boost to its design flight condition. Clean separation from this initial propulsion system stage within less than a second is critical to the success of the flight. This paper discusses the early planning activity, background, and chronology that developed the series of wind tunnel tests to support multi degree of freedom simulation of the separation process. Representative results from each series of tests are presented and issues and concerns during the process and current status will be highlighted.

Hyper-X Stage Separation Wind-Tunnel Test Program

NASA Technical Reports Server (NTRS)

Woods, William C.; Holland, Scott D.; DiFulvio, Michael

2001-01-01

NASA's Hyper-X research program was developed primarily to flight demonstrate a supersonic combustion ramjet engine, fully integrated with a forebody designed to tailor inlet flow conditions and a free expansion nozzle/afterbody to produce positive thrust at design flight conditions. With a point-designed propulsion system the vehicle must depend on some other means for boost to its design flight condition. Clean separation from this initial propulsion system stage within less than a second is critical to the success of the flight. This paper discusses the early planning activity, background, and chronology that developed the series of wind-tunnel tests to support multi-degree-of-freedom simulation of the separation process. Representative results from each series of tests are presented, and issues and concerns during the process and current status are highlighted.

Hyper-X Storage Separation Wind Tunnel Test Program

NASA Technical Reports Server (NTRS)

Woods, William C.; Holland, Scott D.; Difulvio, Michael

2000-01-01

NASA's Hyper-X research program was developed primarily to flight demonstrate a supersonic combustion ramjet engine, fully integrated with a forebody designed to tailor inlet flow, conditions and a free expansion nozzle/afterbody to produce positive thrust at design flight conditions. With a point-designed propulsion system, the vehicle must depend upon some other means for boost to its design flight condition. Clean separation from this initial propulsion system stage within less than a second is critical to the success of the flight. This paper discusses the early planning activity, background, and chronology that developed the series of wind tunnel tests to support multi degree of freedom simulation of the separation process. Representative results from each series of tests are presented and issues and concerns during the process and current status will be highlighted.

Physical exercise improves learning in zebrafish, Danio rerio.

PubMed

Luchiari, Ana Carolina; Chacon, Diana Marques Martins

2013-11-01

Zebrafish is an ideal vertebrate model for neuroscience studies focusing on learning and memory. Although genetic manipulation of zebrafish is available, behavioral protocols are often lacking. In this study we tested whether physical activity can facilitate zebrafish's learning process in an associative conditioning task. Learning was inferred by the approach of the feeding area just after the conditioned stimulus (light). Unexercised zebrafish showed conditioning response from the 5th testing day while fish previously submitted to swim against the water current showed learning by the 3rd day of testing. It seems that physical activity may accelerate associative learning response in zebrafish, indicating the benefits of exercise for cognitive processes. We suggest that this preliminary work could be useful for high throughput screening. Copyright © 2013 Elsevier B.V. All rights reserved.

A Hydrogen Containment Process for Nuclear Thermal Engine Ground testing

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Stewart, Eric; Canabal, Francisco

2016-01-01

The objective of this study is to propose a new total hydrogen containment process to enable the testing required for NTP engine development. This H2 removal process comprises of two unit operations: an oxygen-rich burner and a shell-and-tube type of heat exchanger. This new process is demonstrated by simulation of the steady state operation of the engine firing at nominal conditions.

Eye Movement Analysis of Information Processing under Different Testing Conditions.

ERIC Educational Resources Information Center

Dillon, Ronna F.

1985-01-01

Undergraduates were given complex figural analogies items, and eye movements were observed under three types of feedback: (1) elaborate feedback; (2) subjects verbalized their thinking and application of rules; and (3) no feedback. Both feedback conditions enhanced the rule-governed information processing during inductive reasoning. (Author/GDC)

Retrieving self-vocalized information: An event-related potential (ERP) study on the effect of retrieval orientation.

PubMed

Rosburg, Timm; Johansson, Mikael; Sprondel, Volker; Mecklinger, Axel

2014-11-18

Retrieval orientation refers to a pre-retrieval process and conceptualizes the specific form of processing that is applied to a retrieval cue. In the current event-related potential (ERP) study, we sought to find evidence for an involvement of the auditory cortex when subjects attempt to retrieve vocalized information, and hypothesized that adopting retrieval orientation would be beneficial for retrieval accuracy. During study, participants saw object words that they subsequently vocalized or visually imagined. At test, participants had to identify object names of one study condition as targets and to reject object names of the second condition together with new items. Target category switched after half of the test trials. Behaviorally, participants responded less accurately and more slowly to targets of the vocalize condition than to targets of the imagine condition. ERPs to new items varied at a single left electrode (T7) between 500 and 800ms, indicating a moderate retrieval orientation effect in the subject group as a whole. However, whereas the effect was strongly pronounced in participants with high retrieval accuracy, it was absent in participants with low retrieval accuracy. A current source density (CSD) mapping of the retrieval orientation effect indicated a source over left temporal regions. Independently from retrieval accuracy, the ERP retrieval orientation effect was surprisingly also modulated by test order. Findings are suggestive for an involvement of the auditory cortex in retrieval attempts of vocalized information and confirm that adopting retrieval orientation is potentially beneficial for retrieval accuracy. The effects of test order on retrieval-related processes might reflect a stronger focus on the newness of items in the more difficult test condition when participants started with this condition. Copyright © 2014 Elsevier Inc. All rights reserved.

Pavlovian control of cross-tolerance between pentobarbital and ethanol.

PubMed

Cappell, H; Roach, C; Poulos, C X

1981-01-01

Tolerance to several effects of a number of drugs has been shown to depend on Pavlovian conditioning processes. Experiment I extended the compensatory conditioning model (Siegel 1975) to tolerance to the hypothermic effect of pentobarbital (30 mg/kg). In Experiment I, rats that acquired hypothermic tolerance in one environment did not display tolerance when tested in an environment not previously associated with drug administration. In Experiment II, rats were made tolerant to the hypothermic effect of pentobarbital (30 mg/kg) and tested for cross-tolerance to ethanol (2.5 g/kg). Cross-tolerance was observed, but it was significantly reduced if the test was in an environment different from the one in which tolerance to pentobarbital was originally acquired. Thus, the compensatory conditioning model accounts for at least part of the tolerance and cross-tolerance to the thermic effects of alcohol and pentobarbital. The physiological processes in the CNS underlying tolerance and cross-tolerance for these drugs, therefore, are controlled by associative processes.

Development of optimum process for electron beam cross-linking of high density polyethylene thermal energy storage pellets, process scale-up and production of application qualities of material

NASA Technical Reports Server (NTRS)

Salyer, I. O.

1980-01-01

The electron irradiation conditions required to prepare thermally from stable high density polyethylene (HDPE) were defined. The conditions were defined by evaluating the heat of fusion and the melting temperature of several HDPE specimens. The performance tests conducted on the specimens, including the thermal cycling tests in the thermal energy storage unit are described. The electron beam irradiation tests performed on the specimens, in which the total radiation dose received by the pellets, the electron beam current, the accelerating potential, and the atmospheres were varied, are discussed.

Brain Circuits of Methamphetamine Place Reinforcement Learning: The Role of the Hippocampus-VTA Loop.

PubMed

Keleta, Yonas B; Martinez, Joe L

2012-03-01

The reinforcing effects of addictive drugs including methamphetamine (METH) involve the midbrain ventral tegmental area (VTA). VTA is primary source of dopamine (DA) to the nucleus accumbens (NAc) and the ventral hippocampus (VHC). These three brain regions are functionally connected through the hippocampal-VTA loop that includes two main neural pathways: the bottom-up pathway and the top-down pathway. In this paper, we take the view that addiction is a learning process. Therefore, we tested the involvement of the hippocampus in reinforcement learning by studying conditioned place preference (CPP) learning by sequentially conditioning each of the three nuclei in either the bottom-up order of conditioning; VTA, then VHC, finally NAc, or the top-down order; VHC, then VTA, finally NAc. Following habituation, the rats underwent experimental modules consisting of two conditioning trials each followed by immediate testing (test 1 and test 2) and two additional tests 24 h (test 3) and/or 1 week following conditioning (test 4). The module was repeated three times for each nucleus. The results showed that METH, but not Ringer's, produced positive CPP following conditioning each brain area in the bottom-up order. In the top-down order, METH, but not Ringer's, produced either an aversive CPP or no learning effect following conditioning each nucleus of interest. In addition, METH place aversion was antagonized by coadministration of the N-methyl-d-aspartate (NMDA) receptor antagonist MK801, suggesting that the aversion learning was an NMDA receptor activation-dependent process. We conclude that the hippocampus is a critical structure in the reward circuit and hence suggest that the development of target-specific therapeutics for the control of addiction emphasizes on the hippocampus-VTA top-down connection.

Is evaluative conditioning really uncontrollable? A comparative test of three emotion-focused strategies to prevent the acquisition of conditioned preferences.

PubMed

Gawronski, Bertram; Mitchell, Derek G V; Balas, Robert

2015-10-01

Evaluative conditioning (EC) is defined as the change in the evaluation of a conditioned stimulus (CS) because of its pairing with a valenced unconditioned stimulus (US). Counter to views that EC is the product of automatic learning processes, recent research has revealed various characteristics of nonautomatic processing in EC. The current research investigated the controllability of EC by testing the effectiveness of 3 emotion-focused strategies in preventing the acquisition of conditioned preferences: (a) suppression of emotional reactions to the US, (b) reappraisal of the valence of the US, and (c) facial blocking of emotional responses. Although all 3 strategies reduced EC effects on self-reported evaluations by impairing recollective memory for CS-US pairings, they were ineffective in reducing EC effects on an evaluative priming measure. Regardless of the measure, effective control did not depend on the level of arousal elicited by the US. The results suggest that the 3 strategies can influence deliberate CS evaluations through memory-related processes, but they are ineffective in reducing EC effects on spontaneous evaluative responses. Implications for mental process theories of EC are discussed. (c) 2015 APA, all rights reserved).

Testing linen disinfection procedures in practice with phage-charged-bioindicators.

PubMed

Gerhardts, Anja; Mucha, Helmut; Höfer, Dirk

2012-01-01

Disinfecting laundry processes are essential to avoid contamination of laundering machines and linen during commercial laundry reprocessing in the health care sector. Recently a bacteriophage-charged bioindicator has been developed using MS2 as surrogate virus for testing of low-temperature disinfecting laundry processing on efficacy against viruses related to practice. This paper therefore aims to investigate application of MS2-bioindicators in chemothermal processes under practical conditions (phase 2/step 2) and in practice (phase 3). The experimental design was developed and modified according to the German Society for Hygiene and Microbiology (DGHM) Standard Methods for Testing Chemical Disinfection Processes. Tests under practical conditions were performed at 60 degrees C and 70 degrees C. Additional tests in tunnel washers were carried out at 60 degrees C and 70 degrees C. In all experiments validated disinfecting laundry processes, recommended for bactericidal and virucidal performance (categories A and B), were applied. The results show a temperature-dependent gradual efficacy against the test virus MS2 up to reduction values of more than 8 log10-steps. Therefore MS2-bioindicators prove to be suitable as a tool to determine the performance of disinfection procedures against viruses in practice. Phage-charged bioindicators may be a tool to provide further insights into the reliability of antiviral laundry processes for health care quality management and for infection control.

Seasonal changes in the atmospheric heat balance simulated by the GISS general circulation model

NASA Technical Reports Server (NTRS)

Stone, P. H.; Chow, S.; Helfand, H. M.; Quirk, W. J.; Somerville, R. C. J.

1975-01-01

Tests of the ability of numerical general circulation models to simulate the atmosphere have focussed so far on simulations of the January climatology. These models generally present boundary conditions such as sea surface temperature, but this does not prevent testing their ability to simulate seasonal changes in atmospheric processes that accompany presented seasonal changes in boundary conditions. Experiments to simulate changes in the zonally averaged heat balance are discussed since many simplified models of climatic processes are based solely on this balance.

Effectiveness of the SYSTEM 1E Liquid Chemical Sterilant Processing System for reprocessing duodenoscopes.

PubMed

McDonnell, Gerald; Ehrman, Michele; Kiess, Sara

2016-06-01

A troubling number of health care-acquired infection outbreaks and transmission events, some involving highly resistant microbial pathogens and resulting in serious patient outcomes, have been traced to reusable, high-level disinfected duodenoscopes in the United States. The Food and Drug Administration (FDA) requested a study be conducted to verify liquid chemical sterilization efficacy of SYSTEM 1E(®) Liquid Chemical Sterilant Processing System (STERIS Corporation, Mentor, OH) with varied duodenoscope designs under especially arduous conditions. Here, we describe the system's performance under worst case SYSTEM 1E(®) processing conditions. The test protocol challenged the system's performance by running a fractional cycle to evaluate reduction of recoverable test spores from heavily contaminated endoscopes, including all channels and each distal tip, under worst case SYSTEM 1E(®) processing conditions. All devices were successfully liquid chemically sterilized, showing greater than a 6 log10 reduction of Geobacillus stearothermophilus spores at every inoculation site of each duodenoscope tested, in less than half the exposure time of the standard cycle. The successful outcome of the additional efficacy testing reported here indicates that the SYSTEM 1E(®) is an effective low-temperature liquid chemical sterilization method for duodenoscopes and other critical and semicritical devices. It offers a fast, safe, convenient processing alternative while providing the assurance of a system expressly tested and cleared to achieve liquid chemical sterilization of specific validated duodenoscope models. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

75 FR 19665 - Final Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-15

... processes, including welding, heat treating, and nondestructive testing, are controlled and accomplished by... that when stressed under operating, maintenance, testing, and postulated accident conditions (1) the...

An fMRI study of semantic processing in men with schizophrenia

PubMed Central

Kubicki, M.; McCarley, R.W.; Nestor, P.G.; Huh, T.; Kikinis, R.; Shenton, M.E.; Wible, C.G.

2009-01-01

As a means toward understanding the neural bases of schizophrenic thought disturbance, we examined brain activation patterns in response to semantically and superficially encoded words in patients with schizophrenia. Nine male schizophrenic and 9 male control subjects were tested in a visual levels of processing (LOP) task first outside the magnet and then during the fMRI scanning procedures (using a different set of words). During the experiments visual words were presented under two conditions. Under the deep, semantic encoding condition, subjects made semantic judgments as to whether the words were abstract or concrete. Under the shallow, nonsemantic encoding condition, subjects made perceptual judgments of the font size (uppercase/lowercase) of the presented words. After performance of the behavioral task, a recognition test was used to assess the depth of processing effect, defined as better performance for semantically encoded words than for perceptually encoded words. For the scanned version only, the words for both conditions were repeated in order to assess repetition-priming effects. Reaction times were assessed in both testing scenarios. Both groups showed the expected depth of processing effect for recognition, and control subjects showed the expected increased activation of the left inferior prefrontal cortex (LIPC) under semantic encoding relative to perceptual encoding conditions as well as repetition priming for semantic conditions only. In contrast, schizophrenics showed similar patterns of fMRI activation regardless of condition. Most striking in relation to controls, patients showed decreased LIFC activation concurrent with increased left superior temporal gyrus activation for semantic encoding versus shallow encoding. Furthermore, schizophrenia subjects did not show the repetition priming effect, either behaviorally or as a decrease in LIPC activity. In patients with schizophrenia, LIFC underactivation and left superior temporal gyrus overactivation for semantically encoded words may reflect a disease-related disruption of a distributed frontal temporal network that is engaged in the representation and processing of meaning of words, text, and discourse and which may underlie schizophrenic thought disturbance. PMID:14683698

An fMRI study of semantic processing in men with schizophrenia.

PubMed

Kubicki, M; McCarley, R W; Nestor, P G; Huh, T; Kikinis, R; Shenton, M E; Wible, C G

2003-12-01

As a means toward understanding the neural bases of schizophrenic thought disturbance, we examined brain activation patterns in response to semantically and superficially encoded words in patients with schizophrenia. Nine male schizophrenic and 9 male control subjects were tested in a visual levels of processing (LOP) task first outside the magnet and then during the fMRI scanning procedures (using a different set of words). During the experiments visual words were presented under two conditions. Under the deep, semantic encoding condition, subjects made semantic judgments as to whether the words were abstract or concrete. Under the shallow, nonsemantic encoding condition, subjects made perceptual judgments of the font size (uppercase/lowercase) of the presented words. After performance of the behavioral task, a recognition test was used to assess the depth of processing effect, defined as better performance for semantically encoded words than for perceptually encoded words. For the scanned version only, the words for both conditions were repeated in order to assess repetition-priming effects. Reaction times were assessed in both testing scenarios. Both groups showed the expected depth of processing effect for recognition, and control subjects showed the expected increased activation of the left inferior prefrontal cortex (LIPC) under semantic encoding relative to perceptual encoding conditions as well as repetition priming for semantic conditions only. In contrast, schizophrenics showed similar patterns of fMRI activation regardless of condition. Most striking in relation to controls, patients showed decreased LIFC activation concurrent with increased left superior temporal gyrus activation for semantic encoding versus shallow encoding. Furthermore, schizophrenia subjects did not show the repetition priming effect, either behaviorally or as a decrease in LIPC activity. In patients with schizophrenia, LIFC underactivation and left superior temporal gyrus overactivation for semantically encoded words may reflect a disease-related disruption of a distributed frontal temporal network that is engaged in the representation and processing of meaning of words, text, and discourse and which may underlie schizophrenic thought disturbance.

Enhanced performance of denitrifying sulfide removal process at high carbon to nitrogen ratios under micro-aerobic condition.

PubMed

Chen, Chuan; Zhang, Ruo-Chen; Xu, Xi-Jun; Fang, Ning; Wang, Ai-Jie; Ren, Nan-Qi; Lee, Duu-Jong

2017-05-01

The success of denitrifying sulfide removal (DSR) processes, which simultaneously degrade sulfide, nitrate and organic carbon in the same reactor, counts on synergetic growths of autotrophic and heterotrophic denitrifiers. Feeding wastewaters at high C/N ratio would stimulate overgrowth of heterotrophic bacteria in the DSR reactor so deteriorating the growth of autotrophic denitrifiers. The DSR tests at C/N=1.26:1, 2:1 or 3:1 and S/N =5:6 or 5:8 under anaerobic (control) or micro-aerobic conditions were conducted. Anaerobic DSR process has <50% sulfide removal with no elemental sulfur transformation. Under micro-aerobic condition to remove <5% sulfide by chemical oxidation pathway, 100% sulfide removal is achieved by the DSR consortia. Continuous-flow tests under micro-aerobic condition have 70% sulfide removal and 55% elemental sulfur recovery. Trace oxygen enhances activity of sulfide-oxidizing, nitrate-reducing bacteria to accommodate properly the wastewater with high C/N ratios. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Generating Mechanism of Non-Sustained Disruptive Discharges in Vacuum Interrupters

NASA Astrophysics Data System (ADS)

Hara, Daisuke; Taki, Masayuki; Tanaka, Hitoshi; Okawa, Mikio; Yanabu, Satoru

To develop vacuum circuit breaker (VCB) for higher voltage application, it may be important to understand generating mechanism and its influence of non-sustained disruptive discharges (NSDD) to the systems. So, we carried out the tests using equivalent testing circuit and observed the contacts after testing, For the test, by using commercial vacuum circuit interrupters, AC voltages of 50Hz was applied between contacts for 4 seconds after current interruption, and measured generating frequencies of NSDD vs. the voltages and vs. currents. Typical contact material used in the commercial switching equipment, such as AgWC, CuW, CuCr were tested and compared. Then CuCr's of different composition and manufacturing process are investigated. And CuCr-50 (manufactured by melting process) showed the best performance in all tests. We point out that surface condition may affect the generation of NSDD and also conditioning effect is very important.

The Effects of Involvement, Message Appeal, and Viewing Conditions on Memory and Evaluation of TV Commercials.

ERIC Educational Resources Information Center

Nowak, Glen; Thorson, Esther

A study tested an information processing model that incorporates the concepts of episodic and semantic memory. The model was designed to provide for the concurrent study of three advertising and communication variables: product involvement, message appeal, and distraction in viewing conditions. Among the five hypotheses being tested were that…

Serial and Parallel Attentive Visual Searches: Evidence from Cumulative Distribution Functions of Response Times

ERIC Educational Resources Information Center

Sung, Kyongje

2008-01-01

Participants searched a visual display for a target among distractors. Each of 3 experiments tested a condition proposed to require attention and for which certain models propose a serial search. Serial versus parallel processing was tested by examining effects on response time means and cumulative distribution functions. In 2 conditions, the…

The effect of a third party observer and trait anxiety on neuropsychological performance: the Attentional Control Theory (ACT) perspective.

PubMed

Rezaei, Fatemeh; Hosseini Ramaghani, Nasrin Alsadat; Fazio, Rachel L

2017-04-01

Studies have reported that the presence of a third party observer (TPO) during neuropsychological assessments negatively affects the test performance of the examinee. The present study aimed to investigate the effects of a TPO and trait anxiety on neuropsychological performance according to Attentional Control Theory (ACT). A sample of college students was recruited (n = 318) and then 80 participants were selected to represent the high and low trait anxiety groups. Participants of each of group were randomly assigned to either the NTPO (non-TPO) or TPO conditions. The State-Trait Anxiety Inventory - Trait measure (STAI-T), Wisconsin Card Sorting Test (WCST-64), Stroop test, and Rating Scale for Mental Effort (RSME) were administered to both groups. To analyze the data, univariate ANOVAs were conducted. The results indicated that under the conditions without a TPO the group with high trait anxiety had poorer processing efficiency, but under the conditions with a TPO they had poorer processing efficiency and poorer performance effectiveness than the group with low trait anxiety. In addition, the group with low trait anxiety showed poorer processing efficiency in the TPO compared to non-TPO condition. These findings provide support for the hypotheses of ACT regarding the relation between observer presence and poorer performance on neuropsychological tests, with individuals with higher trait anxiety showing greater negative effects. Implications and suggestions for further research are discussed.

Advanced technologies for scalable ATLAS conditions database access on the grid

NASA Astrophysics Data System (ADS)

Basset, R.; Canali, L.; Dimitrov, G.; Girone, M.; Hawkings, R.; Nevski, P.; Valassi, A.; Vaniachine, A.; Viegas, F.; Walker, R.; Wong, A.

2010-04-01

During massive data reprocessing operations an ATLAS Conditions Database application must support concurrent access from numerous ATLAS data processing jobs running on the Grid. By simulating realistic work-flow, ATLAS database scalability tests provided feedback for Conditions Db software optimization and allowed precise determination of required distributed database resources. In distributed data processing one must take into account the chaotic nature of Grid computing characterized by peak loads, which can be much higher than average access rates. To validate database performance at peak loads, we tested database scalability at very high concurrent jobs rates. This has been achieved through coordinated database stress tests performed in series of ATLAS reprocessing exercises at the Tier-1 sites. The goal of database stress tests is to detect scalability limits of the hardware deployed at the Tier-1 sites, so that the server overload conditions can be safely avoided in a production environment. Our analysis of server performance under stress tests indicates that Conditions Db data access is limited by the disk I/O throughput. An unacceptable side-effect of the disk I/O saturation is a degradation of the WLCG 3D Services that update Conditions Db data at all ten ATLAS Tier-1 sites using the technology of Oracle Streams. To avoid such bottlenecks we prototyped and tested a novel approach for database peak load avoidance in Grid computing. Our approach is based upon the proven idea of pilot job submission on the Grid: instead of the actual query, an ATLAS utility library sends to the database server a pilot query first.

Establishment of an equivalence acceptance criterion for accelerated stability studies.

PubMed

Burdick, Richard K; Sidor, Leslie

2013-01-01

In this article, the use of statistical equivalence testing for providing evidence of process comparability in an accelerated stability study is advocated over the use of a test of differences. The objective of such a study is to demonstrate comparability by showing that the stability profiles under nonrecommended storage conditions of two processes are equivalent. Because it is difficult at accelerated conditions to find a direct link to product specifications, and hence product safety and efficacy, an equivalence acceptance criterion is proposed that is based on the statistical concept of effect size. As with all statistical tests of equivalence, it is important to collect input from appropriate subject-matter experts when defining the acceptance criterion.

Diffusion models of the flanker task: Discrete versus gradual attentional selection

PubMed Central

White, Corey N.; Ratcliff, Roger; Starns, Jeffrey S.

2011-01-01

The present study tested diffusion models of processing in the flanker task, in which participants identify a target that is flanked by items that indicate the same (congruent) or opposite response (incongruent). Single- and dual-process flanker models were implemented in a diffusion-model framework and tested against data from experiments that manipulated response bias, speed/accuracy tradeoffs, attentional focus, and stimulus configuration. There was strong mimcry among the models, and each captured the main trends in the data for the standard conditions. However, when more complex conditions were used, a single-process spotlight model captured qualitative and quantitative patterns that the dual-process models could not. Since the single-process model provided the best balance of fit quality and parsimony, the results indicate that processing in the simple versions of the flanker task is better described by gradual rather than discrete narrowing of attention. PMID:21964663

Increased heart rate after exercise facilitates the processing of fearful but not disgusted faces.

PubMed

Pezzulo, G; Iodice, P; Barca, L; Chausse, P; Monceau, S; Mermillod, M

2018-01-10

Embodied theories of emotion assume that emotional processing is grounded in bodily and affective processes. Accordingly, the perception of an emotion re-enacts congruent sensory and affective states; and conversely, bodily states congruent with a specific emotion facilitate emotional processing. This study tests whether the ability to process facial expressions (faces having a neutral expression, expressing fear, or disgust) can be influenced by making the participants' body state congruent with the expressed emotion (e.g., high heart rate in the case of faces expressing fear). We designed a task requiring participants to categorize pictures of male and female faces that either had a neutral expression (neutral), or expressed emotions whose linkage with high heart rate is strong (fear) or significantly weaker or absent (disgust). Critically, participants were tested in two conditions: with experimentally induced high heart rate (Exercise) and with normal heart rate (Normal). Participants processed fearful faces (but not disgusted or neutral faces) faster when they were in the Exercise condition than in the Normal condition. These results support the idea that an emotionally congruent body state facilitates the automatic processing of emotionally-charged stimuli and this effect is emotion-specific rather than due to generic factors such as arousal.

Retention of Text Material under Cued and Uncued Recall and Open and Closed Book Conditions

ERIC Educational Resources Information Center

Nevid, Jeffrey S.; Pyun, Yea Seul; Cheney, Brianna

2016-01-01

Evidence supports the benefits of effortful processing in strengthening retention of newly learned material. The present study compared two forms of effortful processing, uncued (free) recall and cued recall, under both open and closed book conditions, on both immediate and delayed (one-week) test performance. Participants read a section of a…

Finding a face in the crowd: testing the anger superiority effect in Asperger Syndrome.

PubMed

Ashwin, Chris; Wheelwright, Sally; Baron-Cohen, Simon

2006-06-01

Social threat captures attention and is processed rapidly and efficiently, with many lines of research showing involvement of the amygdala. Visual search paradigms looking at social threat have shown angry faces 'pop-out' in a crowd, compared to happy faces. Autism and Asperger Syndrome (AS) are neurodevelopmental conditions characterised by social deficits, abnormal face processing, and amygdala dysfunction. We tested adults with high-functioning autism (HFA) and AS using a facial visual search paradigm with schematic neutral and emotional faces. We found, contrary to predictions, that people with HFA/AS performed similarly to controls in many conditions. However, the effect was reduced in the HFA/AS group when using widely varying crowd sizes and when faces were inverted, suggesting a difference in face-processing style may be evident even with simple schematic faces. We conclude there are intact threat detection mechanisms in AS, under simple and predictable conditions, but that like other face-perception tasks, the visual search of threat faces task reveals atypical face-processing in HFA/AS.

40 CFR 98.124 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... efficiency test provided that the design, operation, or maintenance of the destruction device has not changed... the last emissions test), you must repeat the emission characterization. Perform the emission... process vent, previous test results, provided the tests are representative of current operating conditions...

40 CFR 98.124 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... efficiency test provided that the design, operation, or maintenance of the destruction device has not changed... the last emissions test), you must repeat the emission characterization. Perform the emission... process vent, previous test results, provided the tests are representative of current operating conditions...

Production development of organic nonflammable spacecraft potting, encapsulating and conformal coating compounds. Volume 3: Appendices

NASA Technical Reports Server (NTRS)

Lieberman, S. L.

1974-01-01

Appendices are presented which include: statement of work; material vendor contacts; formulation/processing data sheet; upward propagation test; flammability test conditions/results sheet; odor test; vacuum stability requirements; flammability test facility; determination of offgassing products and carbon monoxide test; and pneumatic and mechanical impact test guidelines.

A Description of the Development, Capabilities, and Operational Status of the Test SLATE Data Acquisition System at the National Transonic Facility

NASA Technical Reports Server (NTRS)

Cramer, Christopher J.; Wright, James D.; Simmons, Scott A.; Bobbitt, Lynn E.; DeMoss, Joshua A.

2015-01-01

The paper will present a brief background of the previous data acquisition system at the National Transonic Facility (NTF) and the reasoning and goals behind the upgrade to the current Test SLATE (Test Software Laboratory and Automated Testing Environments) data acquisition system. The components, performance characteristics, and layout of the Test SLATE system within the NTF control room will be discussed. The development, testing, and integration of Test SLATE within NTF operations will be detailed. The operational capabilities of the system will be outlined including: test setup, instrumentation calibration, automatic test sequencer setup, data recording, communication between data and facility control systems, real time display monitoring, and data reduction. The current operational status of the Test SLATE system and its performance during recent NTF testing will be highlighted including high-speed, frame-by-frame data acquisition with conditional sampling post-processing applied. The paper concludes with current development work on the system including the capability for real-time conditional sampling during data acquisition and further efficiency enhancements to the wind tunnel testing process.

Development of Crystallizer for Advanced Aqueous Reprocessing Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tadahiro Washiya; Atsuhiro Shibata; Toshiaki Kikuchi

2006-07-01

Crystallization is one of the remarkable technologies for future fuel reprocessing process that has safety and economical advantages. Japan Atomic Energy Agency (JAEA) (former Japan Nuclear Cycle Development Institute), Mitsubishi Material Corporation and Saitama University have been developing the crystallization process. In previous study, we carried out experimental studies with uranium, MOX and spent fuel conditions, and flowsheet analysis was considered. In association with these studies, an innovative continuous crystallizer and its system was developed to ensure high process performance. From the design study, an annular type continuous crystallizer was selected as the most promising design, and performance was confirmedmore » by small-scale test and engineering scale demonstration at uranium crystallization conditions. In this paper, the design study and the demonstration test results are described. (authors)« less

Construction Condition and Damage Monitoring of Post-Tensioned PSC Girders Using Embedded Sensors.

PubMed

Shin, Kyung-Joon; Lee, Seong-Cheol; Kim, Yun Yong; Kim, Jae-Min; Park, Seunghee; Lee, Hwanwoo

2017-08-10

The potential for monitoring the construction of post-tensioned concrete beams and detecting damage to the beams under loading conditions was investigated through an experimental program. First, embedded sensors were investigated that could measure pre-stress from the fabrication process to a failure condition. Four types of sensors were installed on a steel frame, and the applicability and the accuracy of these sensors were tested while pre-stress was applied to a tendon in the steel frame. As a result, a tri-sensor loading plate and a Fiber Bragg Grating (FBG) sensor were selected as possible candidates. With those sensors, two pre-stressed concrete flexural beams were fabricated and tested. The pre-stress of the tendons was monitored during the construction and loading processes. Through the test, it was proven that the variation in thepre-stress had been successfully monitored throughout the construction process. The losses of pre-stress that occurred during a jacking and storage process, even those which occurred inside the concrete, were measured successfully. The results of the loading test showed that tendon stress and strain within the pure span significantly increased, while the stress in areas near the anchors was almost constant. These results prove that FBG sensors installed in a middle section can be used to monitor the strain within, and the damage to pre-stressed concrete beams.

Construction Condition and Damage Monitoring of Post-Tensioned PSC Girders Using Embedded Sensors

PubMed Central

Shin, Kyung-Joon; Lee, Seong-Cheol; Kim, Yun Yong; Kim, Jae-Min; Park, Seunghee; Lee, Hwanwoo

2017-01-01

The potential for monitoring the construction of post-tensioned concrete beams and detecting damage to the beams under loading conditions was investigated through an experimental program. First, embedded sensors were investigated that could measure pre-stress from the fabrication process to a failure condition. Four types of sensors were installed on a steel frame, and the applicability and the accuracy of these sensors were tested while pre-stress was applied to a tendon in the steel frame. As a result, a tri-sensor loading plate and a Fiber Bragg Grating (FBG) sensor were selected as possible candidates. With those sensors, two pre-stressed concrete flexural beams were fabricated and tested. The pre-stress of the tendons was monitored during the construction and loading processes. Through the test, it was proven that the variation in thepre-stress had been successfully monitored throughout the construction process. The losses of pre-stress that occurred during a jacking and storage process, even those which occurred inside the concrete, were measured successfully. The results of the loading test showed that tendon stress and strain within the pure span significantly increased, while the stress in areas near the anchors was almost constant. These results prove that FBG sensors installed in a middle section can be used to monitor the strain within, and the damage to pre-stressed concrete beams. PMID:28796156

Irradiation Tests Supporting LEU Conversion of Very High Power Research Reactors in the US

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woolstenhulme, N. E.; Cole, J. I.; Glagolenko, I.

The US fuel development team is developing a high density uranium-molybdenum alloy monolithic fuel to enable conversion of five high-power research reactors. Previous irradiation tests have demonstrated promising behavior for this fuel design. A series of future irradiation tests will enable selection of final fuel fabrication process and provide data to qualify the fuel at moderately-high power conditions for use in three of these five reactors. The remaining two reactors, namely the Advanced Test Reactor and High Flux Isotope Reactor, require additional irradiation tests to develop and demonstrate the fuel’s performance with even higher power conditions, complex design features, andmore » other unique conditions. This paper reviews the program’s current irradiation testing plans for these moderately-high irradiation conditions and presents conceptual testing strategies to illustrate how subsequent irradiation tests will build upon this initial data package to enable conversion of these two very-high power research reactors.« less

[Quality assurance from the viewpoint of the x-ray film industry].

PubMed

von Volkmann, T

1992-08-01

The parameters of a film-screen-combination are listed in the directive to section 16 of the german X-ray Regulation. These parameters are determined by methods described in DIN standards and published by the manufacturer. Comparable but less precise parameters are determined in the Acceptance Test. For physical reasons it is not possible to determine the speed of an X-ray film or the intensification factor of a screen separately. The films, screens and processing chemicals delivered by the members of the manufacturer association ZVEI are kept below a deviation (expressed as relative contribution to the system speed S) of +/- 10% for the majority of products, the upper limit is +/- 15%. Poor storage and transport conditions may adversely affect the quality of X-ray films. A special labeling of the film box shall serve to guarantee safe distribution channels. The processing conditions are adjusted at the Acceptance Test according to the manufacturers recommendations. The Constancy Test of film processing serves to maintain these correct conditions. Methods deviating from the DIN-method are of limited (Bayerische method) or no value (Stuttgart method).

Influence of hydrophobicity on ice accumulation process under sleet and wind conditions

NASA Astrophysics Data System (ADS)

Xu, Ke; Hu, Jianlin; Shu, Lichun; Jiang, Xingliang; Huang, Zhengyong

2018-03-01

Glaze, the most dangerous ice type in natural environment, forms during sleet weather, which is usually accompanied with wind. The icing performance of hydrophobic coatings under the impact of wind needs further research. This paper studies the influence of hydrophobicity on ice accumulation process under sleet and wind conditions by computer simulations and icing tests. The results indicate that the heat dissipation process of droplets on samples with various hydrophobicity will be accelerated by wind significantly and that a higher hydrophobicity cannot reduce the cooling rate effectively. However, on different hydrophobic surfaces, the ice accumulation process has different characteristics. On a hydrophilic surface, the falling droplets form continuously water film, which will be cooled fast. On superhydrophobic surface, the frozen droplets form ice bulges, which can shield from wind and slow down the heat dissipation process. These ice accumulation characteristics lead to the difference in ice morphology and make a higher hydrophobic surface to have a lower ice mass growth rate in long period icing tests. As a conclusion, superhydrophobic coating remain icephobic under wind and sleet conditions.

Clocking the social mind by identifying mental processes in the IAT with electrical neuroimaging.

PubMed

Schiller, Bastian; Gianotti, Lorena R R; Baumgartner, Thomas; Nash, Kyle; Koenig, Thomas; Knoch, Daria

2016-03-08

Why do people take longer to associate the word "love" with outgroup words (incongruent condition) than with ingroup words (congruent condition)? Despite the widespread use of the implicit association test (IAT), it has remained unclear whether this IAT effect is due to additional mental processes in the incongruent condition, or due to longer duration of the same processes. Here, we addressed this previously insoluble issue by assessing the spatiotemporal evolution of brain electrical activity in 83 participants. From stimulus presentation until response production, we identified seven processes. Crucially, all seven processes occurred in the same temporal sequence in both conditions, but participants needed more time to perform one early occurring process (perceptual processing) and one late occurring process (implementing cognitive control to select the motor response) in the incongruent compared with the congruent condition. We also found that the latter process contributed to individual differences in implicit bias. These results advance understanding of the neural mechanics of response time differences in the IAT: They speak against theories that explain the IAT effect as due to additional processes in the incongruent condition and speak in favor of theories that assume a longer duration of specific processes in the incongruent condition. More broadly, our data analysis approach illustrates the potential of electrical neuroimaging to illuminate the temporal organization of mental processes involved in social cognition.

Clocking the social mind by identifying mental processes in the IAT with electrical neuroimaging

PubMed Central

Schiller, Bastian; Gianotti, Lorena R. R.; Baumgartner, Thomas; Nash, Kyle; Koenig, Thomas; Knoch, Daria

2016-01-01

Why do people take longer to associate the word “love” with outgroup words (incongruent condition) than with ingroup words (congruent condition)? Despite the widespread use of the implicit association test (IAT), it has remained unclear whether this IAT effect is due to additional mental processes in the incongruent condition, or due to longer duration of the same processes. Here, we addressed this previously insoluble issue by assessing the spatiotemporal evolution of brain electrical activity in 83 participants. From stimulus presentation until response production, we identified seven processes. Crucially, all seven processes occurred in the same temporal sequence in both conditions, but participants needed more time to perform one early occurring process (perceptual processing) and one late occurring process (implementing cognitive control to select the motor response) in the incongruent compared with the congruent condition. We also found that the latter process contributed to individual differences in implicit bias. These results advance understanding of the neural mechanics of response time differences in the IAT: They speak against theories that explain the IAT effect as due to additional processes in the incongruent condition and speak in favor of theories that assume a longer duration of specific processes in the incongruent condition. More broadly, our data analysis approach illustrates the potential of electrical neuroimaging to illuminate the temporal organization of mental processes involved in social cognition. PMID:26903643

Implicit and explicit forgetting: when is gist remembered?

PubMed

Dorfman, J; Mandler, G

1994-08-01

Recognition (YES/NO) and stem completion (cued: complete with a word from the list; and uncued: complete with the first word that comes to mind) were tested following either semantic or non-semantic processing of a categorized input list. Item/instance information was tested by contrasting target items from the input list with new items that were categorically related to them; gist/categorical information was tested by comparing target items semantically related to the input items with unrelated new items. For both recognition and stem completion, regardless of initial processing condition, item information decayed rapidly over a period of one week. Gist information was maintained over the same period when initial processing was semantic but only in the cued condition for completion. These results are discussed in terms of dual process theory, which postulates activation/integration of a representation as primarily relevant to implicit item information and elaboration of a representation as mainly relevant to semantic (i.e. categorical) information.

Transfer-appropriate processing in the testing effect.

PubMed

Veltre, Mary T; Cho, Kit W; Neely, James H

2015-01-01

The testing effect is the finding that taking a review test enhances performance on a final test relative to restudying the material. The present experiment investigated transfer-appropriate processing in the testing effect using semantic and orthographic cues to evoke conceptual and data-driven processing, respectively. After a study phase, subjects either restudied the material or took a cued-recall test consisting of half semantic and half orthographic cues in which the correct response was given as feedback. A final, cued-recall test consisted of the identical cue, or a new cue that was of the same type or different type of cue (semantic/orthographic or orthographic/semantic) as that used for that target in the review test. Testing enhanced memory in all conditions. When the review cues and final-test cues were identical, final recall was higher for semantic than orthographic cues. Consistent with test-based transfer-appropriate processing, memory performance improved as the review and final cues became more similar. These results suggest that the testing effect could potentially be caused by the episodic retrieval processes in a final memory test overlapping more with the episodic retrieval processes in a review test than with the encoding operations performed during restudy.

34 CFR 668.141 - Scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... result of test score analyses; and (6) The procedures and conditions under which the Secretary determines that a State process demonstrates that students in the process have the ability to benefit from the...

Evaluation of warm mix asphalt for Alaska conditions : [summary].

DOT National Transportation Integrated Search

2010-09-01

This project developed and tested protocols to determine concrete curing strength during the construction process, so that : building under very cold conditions can be performed safely and quickly. Researchers determined the laboratory strengthmaturi...

Computer Use and Its Effect on the Memory Process in Young and Adults

ERIC Educational Resources Information Center

Alliprandini, Paula Mariza Zedu; Straub, Sandra Luzia Wrobel; Brugnera, Elisangela; de Oliveira, Tânia Pitombo; Souza, Isabela Augusta Andrade

2013-01-01

This work investigates the effect of computer use in the memory process in young and adults under the Perceptual and Memory experimental conditions. The memory condition involved the phases acquisition of information and recovery, on time intervals (2 min, 24 hours and 1 week) on situations of pre and post-test (before and after the participants…

The Orexin Component of Fasting Triggers Memory Processes Underlying Conditioned Food Selection in the Rat

ERIC Educational Resources Information Center

Ferry, Barbara; Duchamp-Viret, Patricia

2014-01-01

To test the selectivity of the orexin A (OXA) system in olfactory sensitivity, the present study compared the effects of fasting and of central infusion of OXA on the memory processes underlying odor-malaise association during the conditioned odor aversion (COA) paradigm. Animals implanted with a cannula in the left ventricle received ICV infusion…

Perceiving age and gender in unfamiliar faces: brain potential evidence for implicit and explicit person categorization.

PubMed

Wiese, Holger; Schweinberger, Stefan R; Neumann, Markus F

2008-11-01

We used repetition priming to investigate implicit and explicit processes of unfamiliar face categorization. During prime and test phases, participants categorized unfamiliar faces according to either age or gender. Faces presented at test were either new or primed in a task-congruent (same task during priming and test) or incongruent (different tasks) condition. During age categorization, reaction times revealed significant priming for both priming conditions, and event-related potentials yielded an increased N170 over the left hemisphere as a result of priming. During gender categorization, congruent faces elicited priming and a latency decrease in the right N170. Accordingly, information about age is extracted irrespective of processing demands, and priming facilitates the extraction of feature information reflected in the left N170 effect. By contrast, priming of gender categorization may depend on whether the task at initial presentation requires configural processing.

Limited evidence of individual differences in holistic processing in different versions of the part-whole paradigm.

PubMed

Sunday, Mackenzie A; Richler, Jennifer J; Gauthier, Isabel

2017-07-01

The part-whole paradigm was one of the first measures of holistic processing and it has been used to address several topics in face recognition, including its development, other-race effects, and more recently, whether holistic processing is correlated with face recognition ability. However the task was not designed to measure individual differences and it has produced measurements with low reliability. We created a new holistic processing test designed to measure individual differences based on the part-whole paradigm, the Vanderbilt Part Whole Test (VPWT). Measurements in the part and whole conditions were reliable, but, surprisingly, there was no evidence for reliable individual differences in the part-whole index (how well a person can take advantage of a face part presented within a whole face context compared to the part presented without a whole face) because part and whole conditions were strongly correlated. The same result was obtained in a version of the original part-whole task that was modified to increase its reliability. Controlling for object recognition ability, we found that variance in the whole condition does not predict any additional variance in face recognition over what is already predicted by performance in the part condition.

Studies and research concerning BNFP: process monitoring and process surveillance demonstration program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kight, H R

1979-11-01

Computerized methods of monitoring process functions and alarming off-standard conditions were implemented and demonstrated during the FY 1979 Uranium Run. In addition, prototype applications of instruments for the purpose of tamper indication and surveillance were tested.

Anxiety, anticipation and contextual information: A test of attentional control theory.

PubMed

Cocks, Adam J; Jackson, Robin C; Bishop, Daniel T; Williams, A Mark

2016-09-01

We tested the assumptions of Attentional Control Theory (ACT) by examining the impact of anxiety on anticipation using a dynamic, time-constrained task. Moreover, we examined the involvement of high- and low-level cognitive processes in anticipation and how their importance may interact with anxiety. Skilled and less-skilled tennis players anticipated the shots of opponents under low- and high-anxiety conditions. Participants viewed three types of video stimuli, each depicting different levels of contextual information. Performance effectiveness (response accuracy) and processing efficiency (response accuracy divided by corresponding mental effort) were measured. Skilled players recorded higher levels of response accuracy and processing efficiency compared to less-skilled counterparts. Processing efficiency significantly decreased under high- compared to low-anxiety conditions. No difference in response accuracy was observed. When reviewing directional errors, anxiety was most detrimental to performance in the condition conveying only contextual information, suggesting that anxiety may have a greater impact on high-level (top-down) cognitive processes, potentially due to a shift in attentional control. Our findings provide partial support for ACT; anxiety elicited greater decrements in processing efficiency than performance effectiveness, possibly due to predominance of the stimulus-driven attentional system.

40 CFR 63.8005 - What requirements apply to my process vessels?

Code of Federal Regulations, 2010 CFR

2010-07-01

... condensers, as defined in § 63.1251, are not considered to be control devices for process vessels. (d... 1 to this subpart, you must conduct the performance test or design evaluation under conditions as specified in § 63.7(e)(1), except that the performance test or design evaluation must be conducted under...

Development and validation of an affinity chromatography step using a peptide ligand for cGMP production of factor VIII.

PubMed

Kelley, Brian D; Tannatt, Molly; Magnusson, Robert; Hagelberg, Sigrid; Booth, James

2004-08-05

An affinity chromatography step was developed for purification of recombinant B-Domain Deleted Factor VIII (BDDrFVIII) using a peptide ligand selected from a phage display library. The peptide library had variegated residues, contained both within a disulfide bond-constrained ring and flanking the ring. The peptide ligand binds to BDDrFVIII with a dissociation constant of approximately 1 microM both in free solution and when immobilized on a chromatographic resin. The peptide is chemically synthesized and the affinity resin is produced by coupling the peptide to an agarose matrix preactivated with N-hydroxysuccinimide. Coupling conditions were optimized to give consistent and complete ligand incorporation and validated with a robustness study that tested various combinations of processing limits. The peptide affinity chromatographic operation employs conditions very similar to an immunoaffinity chromatography step currently in use for BDDrFVIII manufacture. The process step provides excellent recovery of BDDrFVIII from a complex feed stream and reduces host cell protein and DNA by 3-4 logs. Process validation studies established resin reuse over 26 cycles without changes in product recovery or purity. A robustness study using a factorial design was performed and showed that the step was insensitive to small changes in process conditions that represent normal variation in commercial manufacturing. A scaled-down model of the process step was qualified and used for virus removal studies. A validation package addressing the safety of the leached peptide included leaching rate measurements under process conditions, testing of peptide levels in product pools, demonstration of robust removal downstream by spiking studies, end product testing, and toxicological profiling of the ligand. The peptide ligand affinity step was scaled up for cGMP production of BDDrFVIII for clinical trials.

7 CFR 58.928 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.928 Section 58.928... Procedures § 58.928 Quality control tests. All dairy products and other ingredients shall be subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be...

7 CFR 58.335 - Quality control tests.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Quality control tests. 58.335 Section 58.335... Procedures § 58.335 Quality control tests. All milk, cream and related products are subject to inspection for quality and condition throughout each processing operation. Quality control tests shall be made on flow...

Investigation of hazards associated with plastic bonded starter mix manufacturing processes

NASA Technical Reports Server (NTRS)

1971-01-01

An investigation to determine the hazards potential evaluation of plastic bonded starter mix (PBSM) production processes and the application to the M18 and M7A3 grenades is reported. The investigation indicated: (1) the materials with the greatest hazards characteristics, (2) process operating stations most likely to initiate hazardous conditions, (3) the test program required to examine ignition characteristics and process hazards, and (4) the method of handling the accumulated information from testing and safety analyses.

Surveillance of industrial processes with correlated parameters

DOEpatents

White, Andrew M.; Gross, Kenny C.; Kubic, William L.; Wigeland, Roald A.

1996-01-01

A system and method for surveillance of an industrial process. The system and method includes a plurality of sensors monitoring industrial process parameters, devices to convert the sensed data to computer compatible information and a computer which executes computer software directed to analyzing the sensor data to discern statistically reliable alarm conditions. The computer software is executed to remove serial correlation information and then calculate Mahalanobis distribution data to carry out a probability ratio test to determine alarm conditions.

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring.

PubMed

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-02-23

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies.

An Attachable Electromagnetic Energy Harvester Driven Wireless Sensing System Demonstrating Milling-Processes and Cutter-Wear/Breakage-Condition Monitoring

PubMed Central

Chung, Tien-Kan; Yeh, Po-Chen; Lee, Hao; Lin, Cheng-Mao; Tseng, Chia-Yung; Lo, Wen-Tuan; Wang, Chieh-Min; Wang, Wen-Chin; Tu, Chi-Jen; Tasi, Pei-Yuan; Chang, Jui-Wen

2016-01-01

An attachable electromagnetic-energy-harvester driven wireless vibration-sensing system for monitoring milling-processes and cutter-wear/breakage-conditions is demonstrated. The system includes an electromagnetic energy harvester, three single-axis Micro Electro-Mechanical Systems (MEMS) accelerometers, a wireless chip module, and corresponding circuits. The harvester consisting of magnets with a coil uses electromagnetic induction to harness mechanical energy produced by the rotating spindle in milling processes and consequently convert the harnessed energy to electrical output. The electrical output is rectified by the rectification circuit to power the accelerometers and wireless chip module. The harvester, circuits, accelerometer, and wireless chip are integrated as an energy-harvester driven wireless vibration-sensing system. Therefore, this completes a self-powered wireless vibration sensing system. For system testing, a numerical-controlled machining tool with various milling processes is used. According to the test results, the system is fully self-powered and able to successfully sense vibration in the milling processes. Furthermore, by analyzing the vibration signals (i.e., through analyzing the electrical outputs of the accelerometers), criteria are successfully established for the system for real-time accurate simulations of the milling-processes and cutter-conditions (such as cutter-wear conditions and cutter-breaking occurrence). Due to these results, our approach can be applied to most milling and other machining machines in factories to realize more smart machining technologies. PMID:26907297

Influence of Austenitizing Parameters on Mechanical Behavior of Press Hardened Steels

NASA Astrophysics Data System (ADS)

Golem, Lindsay

Recent increases in the Corporate Average Fuel Economy standard have led to an increased focus on lightweight materials for use in vehicle architectures. In particular, press hardened steels (PHS) have been identified as suitable materials to reduce vehicle mass while maintaining or possibly improving vehicle crash performance. A fundamental understanding of the mechanical behavior of PHS with respect to changes in processing conditions is critical to their proper use. In this work, 22MnB5 Al-Si coated blanks were austenitized at several different times and temperatures to produce a range of prior austenite grain sizes. Mechanical behavior was evaluated using smooth sided tensile testing, double edge notch tensile testing, and free bend testing. Metrics, such as notch tensile strength, notch strength ratio, and notch displacement, which is based on the fracture mechanics parameter crack tip opening displacement, were derived from double edge notch tensile testing to assess material notch sensitivity and toughness as a function of processing conditions. Additionally, bend angle at maximum load, post uniform bending slope, and energy for fracture were measured using free bend testing to provide another means for evaluating mechanical behavior. Increasing the austenitizing temperature and hold time resulted in an increase in the measured prior austenite grain size; however, elevated austenitizing temperatures also increased the thickness of the coating interdiffusion layer. In the coated material, tensile strength decreased with increasing prior austenite grain size for both notched and smooth sided tensile samples, but minimal difference was observed in the strain to failure results. Notch displacement, bend angle at maximum load, and energy for fracture during free bend testing all decreased with increasing prior austenite grain size in the coated PHS and also showed a significant drop in measured behavior for the 1025 °C for 30 minutes austenitizing condition, which was not observed in smooth sided tensile testing. The drop in mechanical behavior for this condition was not observed when the coating was removed, which suggests that the interdiffusion layer may degrade the mechanical behavior of PHS. Bend angle at maximum load and energy for fracture in bend testing also decreased for the smallest prior austenite grain size conditions, which was not observed in any of the other testing methods. Results from the three testing methods indicate that differences in the stress and strain state associated with each test influences their ability to discern differences between microstructure and processing conditions of press hardened steels.

Progress in donor assisted coal liquefaction: Hydroaromatic compound formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kottenstette, R.J.; Stephens, H.P.

1993-12-31

The role of hydrogen donor compounds in coal liquefaction has been extensively investigated since the mid 1960`s using model compounds and process derived hydrogen donor solvents. Our recent research and that of other investigators have shown that two model compounds in particular have great efficacy in solvating low rank coals. 1,2,3,10b tetrahydrofluoranthene (H{sub 4}Fl) and 1,2,3,6,7,8 hexahydropyrene (H{sub 6}Py) have been used to dissolve Wyodak coal to > 95% soluble material as measured by tetrahydrofuran (THF). Although these hydrogen donors are very effective, they may not be found in any significant concentrations in actual liquefaction process recycle solvents. Therefore, studiesmore » with process derived recycle materials are necessary to understand donor solvent chemistry. The objective of this paper is to present results of solvent hydrogenation experiments using heavy distillate solvents produced during testing at the Wilsonville Advanced Coal Liquefaction Test Facility. We evaluated the impact of hydrogenation conditions upon hydrogen donor formation in process derived distillates and compared these process derived solvents with the highly effective H{sub 4}Fl and H{sub 6}Py donors in coal liquefaction tests. This paper presents data on reaction conditions used for distillate hydrotreating and subsequent coal liquefaction, with an aim toward understanding the relationship between reaction conditions and donor solvent quality in recycle distillates.« less

Auto-Thermal Reforming of Jet-A Fuel over Commercial Monolith Catalysts: MicroReactor Evaluation and Screening Test Results

NASA Technical Reports Server (NTRS)

Yen, Judy C. H.; Tomsik, Thomas M.

2004-01-01

This paper describes the results of a series of catalyst screening tests conducted with Jet-A fuel under auto-thermal reforming (ATR) process conditions at the research laboratories of SOFCo-EFS Holdings LLC under Glenn Research Center Contract. The primary objective is to identify best available catalysts for future testing at the NASA GRC 10-kW(sub e) reformer test facility. The new GRC reformer-injector test rig construction is due to complete by March 2004. Six commercially available monolithic catalyst materials were initially selected by the NASA/SOFCo team for evaluation and bench scale screening in an existing 0.05 kW(sub e) microreactor test apparatus. The catalyst screening tests performed lasted 70 to 100 hours in duration in order to allow comparison between the different samples over a defined range of ATR process conditions. Aging tests were subsequently performed with the top two ranked catalysts as a more representative evaluation of performance in a commercial aerospace application. The two catalyst aging tests conducted lasting for approximately 600 hours and 1000 hours, respectively.

Time dependent effects of stress prior to encoding on event-related potentials and 24 h delayed retrieval.

PubMed

Quaedflieg, Conny W E M; Schwabe, Lars; Meyer, Thomas; Smeets, Tom

2013-12-01

Stress can exert profound effects on memory encoding. Here, we investigated whether (sub)cortical information processing during encoding and memory retrieval at a 24 h delayed test are affected by the temporal proximity between stress and memory encoding. Sixty-four participants engaged in the Maastricht Acute Stress Test (MAST) or a no-stress control condition either immediately before (i.e., proximate condition) or 30 min before (i.e., distant condition) a picture encoding task. In general, stress decreased the number of freely recalled and recognized pictures and increased the number of false alarms. However, timing of stress exposure did not differentially affect picture recall, recognition or selective attention processes (i.e., LPP). Nevertheless, stress-induced cortisol responses and correctly recognized neutral pictures were positively associated within the proximate stress condition but negatively associated within the distant stress condition. These findings suggest that the time at which a stressor is applied might differentially impact the association between stress-induced cortisol elevations and memory formation and indicate the need for a finer delineation of the time window during which glucocorticoids affect memory formation processes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Improved Signal Processing Technique Leads to More Robust Self Diagnostic Accelerometer System

NASA Technical Reports Server (NTRS)

Tokars, Roger; Lekki, John; Jaros, Dave; Riggs, Terrence; Evans, Kenneth P.

2010-01-01

The self diagnostic accelerometer (SDA) is a sensor system designed to actively monitor the health of an accelerometer. In this case an accelerometer is considered healthy if it can be determined that it is operating correctly and its measurements may be relied upon. The SDA system accomplishes this by actively monitoring the accelerometer for a variety of failure conditions including accelerometer structural damage, an electrical open circuit, and most importantly accelerometer detachment. In recent testing of the SDA system in emulated engine operating conditions it has been found that a more robust signal processing technique was necessary. An improved accelerometer diagnostic technique and test results of the SDA system utilizing this technique are presented here. Furthermore, the real time, autonomous capability of the SDA system to concurrently compensate for effects from real operating conditions such as temperature changes and mechanical noise, while monitoring the condition of the accelerometer health and attachment, will be demonstrated.

Memory for pictures and words as a function of level of processing: Depth or dual coding?

PubMed

D'Agostino, P R; O'Neill, B J; Paivio, A

1977-03-01

The experiment was designed to test differential predictions derived from dual-coding and depth-of-processing hypotheses. Subjects under incidental memory instructions free recalled a list of 36 test events, each presented twice. Within the list, an equal number of events were assigned to structural, phonemic, and semantic processing conditions. Separate groups of subjects were tested with a list of pictures, concrete words, or abstract words. Results indicated that retention of concrete words increased as a direct function of the processing-task variable (structural < phonemic

Enhanced Cognitive Rehabilitation to Treat Comorbid TBI and PTSD

DTIC Science & Technology

2017-12-01

13. SUPPLEMENTARY NOTES 14. ABSTRACT This was a randomized controlled treatment study to test a modification of Cognitive Processing Therapy (CPT) for...combination of conditions which often complicates recovery from either condition. Emotional symptoms are likely a main cause of the persistence of post ... tested a modification of CPT in which CPT was enhanced with compensatory cognitive rehabilitation principles detailed in CogSMART. The enhanced CPT

Testing neuropsychological hypotheses for cognitive deficits in psychopathic criminals: a study of global-local processing.

PubMed

Kosson, David S; Miller, Sarah K; Byrnes, Katherine A; Leveroni, Catherine L

2007-03-01

Competing hypotheses about neuropsychological mechanisms underlying psychopathy are seldom examined in the same study. We tested the left hemisphere activation hypothesis and the response modulation hypothesis of psychopathy in 172 inmates completing a global-local processing task under local bias, global bias, and neutral conditions. Consistent with the left hemisphere activation hypothesis, planned comparisons showed that psychopathic inmates classified local targets more slowly than nonpsychopathic inmates in a local bias condition and exhibited a trend toward similar deficits for global targets in this condition. However, contrary to the response modulation hypothesis, psychopaths were no slower to respond to local targets in a global bias condition. Because psychopathic inmates were not generally slower to respond to local targets, results are also not consistent with a general left hemisphere dysfunction account. Correlational analyses also indicated deficits specific to conditions presenting most targets at the local level initially. Implications for neuropsychological conceptualizations of psychopathy are considered.

Tribological investigations of the applicability of surface functionalization for dry extrusion processes

NASA Astrophysics Data System (ADS)

Teller, Marco; Prünte, Stephan; Ross, Ingo; Temmler, André; Schneider, Jochen M.; Hirt, Gerhard

2017-10-01

Cold extrusion processes are characterized by large relative contact stresses combined with a severe surface enlargement of the workpiece. Under these process conditions a high risk for galling of workpiece material to the tool steel occurs especially in processing of aluminum and aluminum alloys. In order to reduce adhesive wear lubricants for separation of workpiece and tool surfaces are used. As a consequence additional process steps (e.g. preparation and cleaning of workpieces) are necessary. Thus, the realization of a dry forming process is aspired from an environmental and economic perspective. In this paper a surface functionalization with self-assembled-monolayers (SAM) of the tool steels AISI D2 (DIN 1.2379) and AISI H11 (DIN 1.2343) is evaluated by a process-oriented tribological test. The tribological experiment is able to resemble and scale the process conditions of cold extrusion related to relative contact stress and surface enlargement for the forming of pure aluminum (Al99.5). The effect of reduced relative contact stress, surface enlargement and relative velocity on adhesive wear and tool lifetime is evaluated. Similar process conditions are achievable by different die designs with decreased extrusion ratios and adjusted die angles. The effect of surface functionalization critically depends on the substrate material. The different microstructure and the resulting differences in surface chemistry of the two tested tool steels appear to affect the performance of the tool surface functionalization with SAM.

Site Simulation of Solidified Peat: Lab Monitoring

NASA Astrophysics Data System (ADS)

Durahim, N. H. Ab; Rahman, J. Abd; Tajuddin, S. F. Mohd; Mohamed, R. M. S. R.; Al-Gheethi, A. A.; Kassim, A. H. Mohd

2018-04-01

In the present research, the solidified peat on site simulation is conducted to obtain soil leaching from soil column study. Few raw materials used in testing such as Ordinary Portland Cement (OPC), Fly ash (FA) and bottom ash (BA) which containing in solidified peat (SP), fertilizer (F), and rainwater (RW) are also admixed in soil column in order to assess their effects. This research was conducted in two conditions which dry and wet condition. Distilled water used to represent rainfall during flushing process while rainwater used to gain leaching during dry and wet condition. The first testing made after leaching process done was Moisture Content (MC). Secondly, Unconfined Compressive Strength (UCS) will be conducted on SP to know the ability of SP strength. These MC and UCS were made before and after SP were applied in soil column. Hence, the both results were compared to see the reliability occur on SP. All leachate samples were tested using Absorption Atomic Spectroscopy (AAS), Ion Chromatography (IC) and Inductively-Coupled Plasma Spectrophotometry (ICP-MS) testing to know the anion and cation present in it.

Surveillance of industrial processes with correlated parameters

DOEpatents

White, A.M.; Gross, K.C.; Kubic, W.L.; Wigeland, R.A.

1996-12-17

A system and method for surveillance of an industrial process are disclosed. The system and method includes a plurality of sensors monitoring industrial process parameters, devices to convert the sensed data to computer compatible information and a computer which executes computer software directed to analyzing the sensor data to discern statistically reliable alarm conditions. The computer software is executed to remove serial correlation information and then calculate Mahalanobis distribution data to carry out a probability ratio test to determine alarm conditions. 10 figs.

Numerical and experimental analysis of a ducted propeller designed by a fully automated optimization process under open water condition

NASA Astrophysics Data System (ADS)

Yu, Long; Druckenbrod, Markus; Greve, Martin; Wang, Ke-qi; Abdel-Maksoud, Moustafa

2015-10-01

A fully automated optimization process is provided for the design of ducted propellers under open water conditions, including 3D geometry modeling, meshing, optimization algorithm and CFD analysis techniques. The developed process allows the direct integration of a RANSE solver in the design stage. A practical ducted propeller design case study is carried out for validation. Numerical simulations and open water tests are fulfilled and proved that the optimum ducted propeller improves hydrodynamic performance as predicted.

Effect of Microstructure on the Mechanical Properties of Extruded Magnesium and a Magnesium Alloy

NASA Astrophysics Data System (ADS)

McGhee, Paul

The main objective of this research was to investigate the relationship between the fatigue behavior and crystallographic texture evolution of magnesium (Mg) alloys with a range of microalloying element content processed under various extrusion conditions. Several Mg alloys were processed under a range of extrusion temperatures, extrusion ratios, and alloying content and tested under monotonic and cyclic fatigue loading conditions: fully-reversed condition tested at strain amplitudes of 0.15% - 1.00% in strain-control mode. After fatigue testing, Mg microstructural analysis was performed using SEM, TEM, optical microscopy, and X-ray diffraction techniques. Microstructural observations revealed significant grain refinement through a combination of zirconium (Zr) addition and hot-extrusion, producing fine equiaxed grain structure with grain sizes ranging between 1-5 microm. Texture analysis and partial compression testing results showed that the initial texture of the extruded alloy gradually evolved upon compressive loading along the c-axes inducing extension twinning creating a strong basal texture along the extrusion direction. Full tensile and compression testing at room temperature showed that the combination of hot extrusion and Zr addition can further refine the grains of the Mg alloys microstructure and enhance the texture while simultaneously enhancing the mechanical properties.

Telerobotic electronic materials processing experiment

NASA Technical Reports Server (NTRS)

Ollendorf, Stanford

1991-01-01

The Office of Commercial Programs (OCP), working in conjunction with NASA engineers at the Goddard Space Flight Center, is supporting research efforts in robot technology and microelectronics materials processing that will provide many spinoffs for science and industry. The Telerobotic Materials Processing Experiment (TRMPX) is a Shuttle-launched materials processing test payload using a Get Away Special can. The objectives of the project are to define, develop, and demonstrate an automated materials processing capability under realistic flight conditions. TRMPX will provide the capability to test the production processes that are dependent on microgravity. The processes proposed for testing include the annealing of amorphous silicon to increase grain size for more efficient solar cells, thin film deposition to demonstrate the potential of fabricating solar cells in orbit, and the annealing of radiation damaged solar cells.

Leaching behaviour of hazardous waste under the impact of different ambient conditions.

PubMed

Pecorini, Isabella; Baldi, Francesco; Bacchi, Donata; Carnevale, Ennio Antonio; Corti, Andrea

2017-05-01

The overall objective of this study is to provide an improved basis for the assessment of the leaching behaviour of waste marked as hazardous partly stabilised (European waste catalogue code 19 03 04 ∗ ). Four samples of hazardous partly stabilised waste were subjected to two leaching tests: up-flow column tests and batch equilibrium tests. The research was carried out in two directions: the first aims at comparing the results of the two experimental setups while the second aims at assessing the impact of different ambient conditions on the leaching behaviour of waste. Concerning this latter objective the effect of mesophilic temperature, mechanical constraints and acid environment were tested through column percolation tests. Results showed no significant differences between batch and column leaching test outcomes when comparing average concentrations calculated at a liquid to solid ratio of 10:1 l kg -1  TS. Among the tested ambient conditions, the presence of an acid environment (pH=4.5) accelerated the leaching process resulting in a higher cumulative released quantity measured on the majority of the investigated polluting substances. On the contrary, the effect of temperature and mechanical constraints seemed to not affect the process showing final contents even lower than values found for the standard test. This result was furthermore confirmed by the application of the principal component analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Effects of Hygrothermal Aging on the Impact Penetration Resistance of Triaxially Braided Composites

NASA Technical Reports Server (NTRS)

Pereira, J. Michael; Revilock, Duane M.; Ruggeri, Charles R.; Roberts, Gary D.; Kohlman, Lee W.; Miller, Sandi G.

2016-01-01

An experimental study was conducted to measure the effects of long term hygrothermal aging on the impact penetration resistance of triaxially braided polymer composites. Flat panels of three different materials were subjected to repeated cycles of high and low temperature and high and low humidity for two years. Samples of the panels were periodically tested under impact loading during the two year time period. The purpose of the study was to identify and quantify any degradation in impact penetration resistance of these composites under cyclic temperature and humidity conditions experienced by materials in the fan section of commercial gas turbine engines for a representative aircraft flight cycle. The materials tested consisted of Toray ® T700S carbon fibers in a 2D triaxial braid with three different resins, Cycom® PR520, a toughened resin, Hercules® 3502, an untoughened resin and EPON 862, intermediate between the two. The fiber preforms consisted of a quasi-isotropic 0/+60/-60 braid with 24K tows in the axial direction and 12K tows in the bias directions. The composite panels were manufactured using a resin transfer molding process producing panels with a thickness of 0.125 inches. The materials were tested in their as-processed condition and again after one year and two years of aging (1.6 years in the case of E862). The aging process involved subjecting the test panels to two cycles per day of high and low temperature and high and low humidity. A temperature range of -60degF to 250degF and a humidity range of 0 to 85% rh was used to simulate extreme conditions for composite components in the fan section of a commercial gas turbine engine. Additional testing was conducted on the as-processed PR520 composite under cryogenic conditions. After aging there was some change in the failure pattern, but there was no reduction in impact penetration threshold for any of the three systems, and in the case of the 3502 system, a significant increase in penetration threshold. There was also an increase in the penetration resistance of the PR520 system impacted under cryogenic conditions.

Oxygen Transfer in Moving Bed Biofilm Reactor and Integrated Fixed Film Activated Sludge Processes.

PubMed

2017-11-17

A demonstrated approach to design the, so-called, medium-bubble air diffusion network for oxygen transfer into the aerobic zone(s) of moving bed biofilm reactor (MBBR) and integrated fixed-film activated sludge (IFAS) processes is described in this paper. Operational full-scale biological water resource recovery systems treating municipal sewerage demonstrate that medium-bubble air diffusion networks designed using the method presented here provide reliable service. Further improvement is possible, however, as knowledge gaps prevent more rational process designs. Filling such knowledge gaps can potentially result in higher performing and more economical systems. Small-scale system testing demonstrates significant enhancement of oxygen transfer capacity due to the presence of media, but quantification of such effects in full-scale systems is lacking, and is needed. Establishment of the relationship between diffuser submergence, aeration rate, and biofilm carrier fill fraction will enhance MBBR and IFAS aerobic process design, cost, and performance. Limited testing of full-scale systems is available to allow computation of alpha valuess. As with clean water testing of full-scale systems, further full-scale testing under actual operating conditions is required to more fully quantify MBBR and IFAS system oxygen transfer performance under a wide range of operating conditions. Control of MBBR and IFAS aerobic zone oxygen transfer systems can be optimized by recognizing that varying residual dissolved oxygen (DO) concentrations are needed, depending on operating conditions. For example, the DO concentration in the aerobic zone of nitrifying IFAS processes can be lowered during warm weather conditions when greater suspended growth nitrification can occur, resulting in the need for reduced nitrification by the biofilm compartment. Further application of oxygen transfer control approaches used in activated sludge systems to MBBR and IFAS systems, such as ammonia-based oxygen transfer system control, has been demonstrated to further improve MBBR and IFAS system energy-efficiency.

Improved silicon nitride for advanced heat engines

NASA Technical Reports Server (NTRS)

Yeh, Hun C.; Fang, Ho T.

1987-01-01

The technology base required to fabricate silicon nitride components with the strength, reliability, and reproducibility necessary for actual heat engine applications is presented. Task 2 was set up to develop test bars with high Weibull slope and greater high temperature strength, and to conduct an initial net shape component fabrication evaluation. Screening experiments were performed in Task 7 on advanced materials and processing for input to Task 2. The technical efforts performed in the second year of a 5-yr program are covered. The first iteration of Task 2 was completed as planned. Two half-replicated, fractional factorial (2 sup 5), statistically designed matrix experiments were conducted. These experiments have identified Denka 9FW Si3N4 as an alternate raw material to GTE SN502 Si3N4 for subsequent process evaluation. A detailed statistical analysis was conducted to correlate processing conditions with as-processed test bar properties. One processing condition produced a material with a 97 ksi average room temperature MOR (100 percent of goal) with 13.2 Weibull slope (83 percent of goal); another condition produced 86 ksi (6 percent over baseline) room temperature strength with a Weibull slope of 20 (125 percent of goal).

Development of passion fruit juice beverage

NASA Astrophysics Data System (ADS)

Zhu, Xiang-hao; Duan, Zhen-hua; Yang, Yu-xia; Huang, Xin-hui; Xu, Cheng-ling; Huang, Zhi-zhuo

2017-12-01

In this experiment, the whole fruit of passion fruit was used as raw material. The effects of the ratio of material to liquid (RML), the amount of sucrose addition and the pH on the quality of passion fruit juice beverage were investigated by single factor test. And the optimum process conditions of passion fruit juice beverage were determined by orthogonal test. The results show that the optimum process paramenters were as follow: RML was 1:3, pH was 4.0 and sucrose addition was 8%. Under such optimal conditions, the color of passion fruit juice beverage was red, the flavor of passion fruit was rich and it tasted pleasant.

Psychosocial work conditions, perceived stress, perceived muscular tension, and neck/shoulder symptoms among medical secretaries.

PubMed

Larsman, Pernilla; Kadefors, Roland; Sandsjö, Leif

2013-01-01

Unfavorable psychosocial working conditions are hypothesized to lead to perceived stress, which, in turn, can be related to an increased risk of development of neck/shoulder symptoms through increased and sustained muscle activation. The aim of the present study was to test this hypothesized process model among medical secretaries, a female-dominated profession characterized by a high amount of visual display unit use and a high prevalence of neck/shoulder symptoms. In this cross-sectional study, a questionnaire survey was conducted among medical secretaries (n = 200). The proposed process model was tested using a path model framework. The results indicate that high work demands were related to high perceived stress, which in turn was related to a high perceived muscle tension and neck/shoulder symptoms. Low influence at work was not related to perceived stress, but was directly related to a high perceived muscle tension. In general, these cross-sectional results lend tentative support for the hypothesis that adverse psychosocial work conditions (high work demands) may contribute to the development of neck/shoulder symptoms through the mechanism of stress-induced sustained muscular activation. This process model needs to be further tested in longitudinal studies.

Challenges of Cold Conditioning and Static Testing the Second Ares Demonstration Motor (DM-2)

NASA Technical Reports Server (NTRS)

Quinn, Shyla; Davis, Larry C.

2011-01-01

On August 31, 2010, a five-segment demonstration motor (DM) for the Ares program was successfully tested. A series of demonstration motors (DMs) will be tested in different conditioned environments to confirm they meet their design specifications. The second demonstration motor (DM-2) was the first cold motor. The motor needed to be subjected to sub-freezing temperatures for two months so that its internal propellant mean bulk temperature (PMBT) was approximately 40 F. Several challenges had to be overcome to make this a successful test. One challenge was to condition four field joints to get the O-rings approximately 32 F. This would be done by applying conditioning shrouds to externally cool each field joint after the test bay was pulled off. The purpose of this conditioning was to validate the new O-ring design and allow joint heaters to be eliminated. Another challenge was maintaining temperature requirements for components in the nozzle vectoring system. A separate heating system was used to warm these components during cold conditioning. There were 53 test objectives that required 764 channels of data to be recorded; 460 were specific to DM-2. This instrumentation had to be installed prior to conditioning, which meant the baseline process and timeline had to be modified to meet this time critical schedule.

An optimal method for phosphorylation of rare earth chlorides in LiCl-KCl eutectic based waste salt

NASA Astrophysics Data System (ADS)

Eun, H. C.; Kim, J. H.; Cho, Y. Z.; Choi, J. H.; Lee, T. K.; Park, H. S.; Park, G. I.

2013-11-01

A study on an optimal method for the phosphorylation of rare earth chlorides in LiCl-KCl eutectic waste salt generated the pyrochemical process of spent nuclear fuel was performed. A reactor with a pitched four blade impeller was designed to create a homogeneous mixing zone in LiCl-KCl eutectic salt. A phosphorylation test of NdCl3 in the salt was carried out by changing the operation conditions (operation temperature, stirring rate, agent injection amount). Based on the results of the test, a proper operation condition (450 °C, 300 rpm, 1 eq. of phosphorylation agent) for over a 0.99 conversion ratio of NdCl3 to NdPO4 was determined. Under this condition, multi-component rare earth (La, Ce, Pr, Nd, Sm, Eu, Gd, Y) chlorides were effectively converted into phosphate forms. It was confirmed that the existing regeneration process of LiCl-KCl eutectic waste salt can be greatly improved and simplified through these phosphorylation test results.

THERMAL DEPOLYMERIZATION OF POSTCONSUMER PLASTICS

EPA Science Inventory

The University of North Dakota Energy & Environmental Research Center (EERC) performed two series of tests to evaluate process conditions for thermal depolymerization of postconsumer plastics. The objective of the first test series was to provide data for optimization of reactio...

Testing solar panels for small-size satellites: the UPMSAT-2 mission

NASA Astrophysics Data System (ADS)

Roibás-Millán, E.; Alonso-Moragón, A.; Jiménez-Mateos, A. G.; Pindado, S.

2017-11-01

At present, the development of small-size satellites by universities, companies and research institutions has become usual practice, and is spreading rapidly. In this kind of project cost plays a significant role. One of the main areas are the assembly, integration and test (AIT) plans, which carry an associated cost for simulating environmental conditions. For instance, in the power subsystems test and, in particular, in the testing of solar panels, the irradiance and temperature conditions might be optimum so the performance of the system can be shown next to real operational conditions. To reproduce the environmental conditions in terms of irradiance, solar simulators are usually used, which carries an associated increase in cost for testing the equipment. The aim of this paper is to present an alternative and inexpensive way to perform AIT plans on spacecraft power subsystems, from a testing campaign performed using outdoor clean-sky conditions and an isolation system to protect the panels. A post-process of the measured data is therefore needed, taking into account the conditions in which the test has been accomplished. The I-V characteristics obtained are compared with a theoretical 1-diode/2-resistor equivalent electric circuit, achieving enough precision based solely on the manufacturer’s data.

Studies of the physical, yield and failure behavior of aliphatic polyketones

NASA Astrophysics Data System (ADS)

Karttunen, Nicole Renee

This thesis describes an investigation into the multiaxial yield and failure behavior of an aliphatic polyketone terpolymer. The behavior is studied as a function of: stress state, strain rate, temperature, and sample processing conditions. Results of this work include: elucidation of the behavior of a recently commercialized polymer, increased understanding of the effects listed above, insight into the effects of processing conditions on the morphology of the polyketone, and a description of yield strength of this material as a function of stress state, temperature, and strain rate. The first portion of work focuses on the behavior of a set of samples that are extruded under "common" processing conditions. Following this reference set of tests, the effect of testing this material at different temperatures is studied. A total of four different temperatures are examined. In addition, the effect of altering strain rate is examined. Testing is performed under pseudo-strain rate control at constant nominal octahedral shear strain rate for each failure envelope. A total of three different rates are studied. An extension of the first portion of work involves modeling the yield envelope. This is done by combining two approaches: continuum level and molecular level. The use of both methods allows the description of the yield envelope as a function of stress state, strain rate and temperature. The second portion of work involves the effects of processing conditions. For this work, additional samples are extruded with different shear and thermal histories than the "standard" material. One set of samples is processed with shear rates higher and lower than the standard. A second set is processed at higher and lower cooling rates than the standard. In order to understand the structural cause for changes in behavior with processing conditions, morphological characterization is performed on these samples. In particular, the effect on spherulitic structure is important. Residual stresses are also determined to be important to the behavior of the samples. Finally, an investigation into the crystalline structure of a family of aliphatic polyketones is performed. The effects of side group concentration and size are described.

A laboratory evaluation of four quality control devices for radiographic processing.

PubMed

Rushton, V E; Horner, K

1994-08-01

Quality assurance programmes for radiographic processing traditionally employ expensive sensitometric and densitometric techniques. However cheap and simple devices for monitoring radiographic processing are available. The aim of this study was to make a comparison of four such devices in terms of their ability to detect variations in radiographic density of clinical significance. Three of the devices are commercially available while the fourth is easily manufactured from waste materials. Ideal bitewing exposure times were selected for four different kilovoltage/film speed combinations. Phantom bitewing radiographs, exposed using these exposure times, were processed using a variety of times and developer temperatures to simulate variations in radiographic quality due to inadequate processing conditions. Test films, produced using the four monitoring devices, were exposed and processed under identical conditions. The phantom bitewings were judged to have 'acceptable' quality when the optical density of that part of the film not showing calcified structures was within +/- 0.5 of that of the film processed under optimal conditions. The efficacy of the monitoring devices in indicating the adequacy of processing was assessed by a comparison of their readings with those made from the phantom bitewings. None of the monitoring devices was ideal for all the kilovoltage/film speed combinations tested, but the homemade device proved to be the most generally effective. We conclude that guidelines to dentists on radiographic quality assurance should include reference to and details of this simple device.

Effects of filler type and content on mechanical properties of photopolymerizable composites measured across two-dimensional combinatorial arrays.

PubMed

Lin-Gibson, Sheng; Sung, Lipiin; Forster, Aaron M; Hu, Haiqing; Cheng, Yajun; Lin, Nancy J

2009-07-01

Multicomponent formulations coupled with complex processing conditions govern the final properties of photopolymerizable dental composites. In this study, a single test substrate was fabricated to support multiple formulations with a gradient in degree of conversion (DC), allowing the evaluation of multiple processing conditions and formulations on one specimen. Mechanical properties and damage response were evaluated as a function of filler type/content and irradiation. DC, surface roughness, modulus, hardness, scratch deformation and cytotoxicity were quantified using techniques including near-infrared spectroscopy, laser confocal scanning microscopy, depth-sensing indentation, scratch testing and cell viability. Scratch parameters (depth, width, percent recovery) were correlated to composite modulus and hardness. Total filler content, nanofiller and irradiation time/intensity all affected the final properties, with the dominant factor for improved properties being a higher DC. This combinatorial platform accelerates the screening of dental composites through the direct comparison of properties and processing conditions across the same sample.

The role of shape recognition in figure/ground perception in infancy.

PubMed

White, Hannah; Jubran, Rachel; Heck, Alison; Chroust, Alyson; Bhatt, Ramesh S

2018-04-30

In this study we sought to determine whether infants, like adults, utilize previous experience to guide figure/ground processing. After familiarization to a shape, 5-month-olds preferentially attended to the side of an ambiguous figure/ground test stimulus corresponding to that shape, suggesting that they were viewing that portion as the figure. Infants' failure to exhibit this preference in a control condition in which both sides of the test stimulus were displayed as figures indicated that the results in the experimental condition were not due to a preference between two figure shapes. These findings demonstrate for the first time that figure/ground processing in infancy is sensitive to top-down influence. Thus, a critical aspect of figure/ground processing is functional early in life.

The Effect of Adaptive Nonlinear Frequency Compression on Phoneme Perception.

PubMed

Glista, Danielle; Hawkins, Marianne; Bohnert, Andrea; Rehmann, Julia; Wolfe, Jace; Scollie, Susan

2017-12-12

This study implemented a fitting method, developed for use with frequency lowering hearing aids, across multiple testing sites, participants, and hearing aid conditions to evaluate speech perception with a novel type of frequency lowering. A total of 8 participants, including children and young adults, participated in real-world hearing aid trials. A blinded crossover design, including posttrial withdrawal testing, was used to assess aided phoneme perception. The hearing aid conditions included adaptive nonlinear frequency compression (NFC), static NFC, and conventional processing. Enabling either adaptive NFC or static NFC improved group-level detection and recognition results for some high-frequency phonemes, when compared with conventional processing. Mean results for the distinction component of the Phoneme Perception Test (Schmitt, Winkler, Boretzki, & Holube, 2016) were similar to those obtained with conventional processing. Findings suggest that both types of NFC tested in this study provided a similar amount of speech perception benefit, when compared with group-level performance with conventional hearing aid technology. Individual-level results are presented with discussion around patterns of results that differ from the group average.

No childhood development of viewpoint-invariant face recognition: evidence from 8-year-olds and adults.

PubMed

Crookes, Kate; Robbins, Rachel A

2014-10-01

Performance on laboratory face tasks improves across childhood, not reaching adult levels until adolescence. Debate surrounds the source of this development, with recent reviews suggesting that underlying face processing mechanisms are mature early in childhood and that the improvement seen on experimental tasks instead results from general cognitive/perceptual development. One face processing mechanism that has been argued to develop slowly is the ability to encode faces in a view-invariant manner (i.e., allowing recognition across changes in viewpoint). However, many previous studies have not controlled for general cognitive factors. In the current study, 8-year-olds and adults performed a recognition memory task with two study-test viewpoint conditions: same view (study front view, test front view) and change view (study front view, test three-quarter view). To allow quantitative comparison between children and adults, performance in the same view condition was matched across the groups by increasing the learning set size for adults. Results showed poorer memory in the change view condition than in the same view condition for both adults and children. Importantly, there was no quantitative difference between children and adults in the size of decrement in memory performance resulting from a change in viewpoint. This finding adds to growing evidence that face processing mechanisms are mature early in childhood. Copyright © 2014 Elsevier Inc. All rights reserved.

Flight and Operational Medicine Clinic (FOMC) Task Process Mapping

DTIC Science & Technology

2014-03-01

technicians, nurses, and physician assistants to accomplish the majority of the tasks; physician level tasks are few and primarily involve application of...condition 31, 37, 81? Complete evaluation Present 469 within 5 days of positive pregnancy test Is condition duty/fitness? NO End Process YES Send to ...info to Health IT Ancillary exam module provides requirements/ sends info to Health IT (Audiology, Optometry, Dental , Mental Health) Operational

Memory in pregnancy and post-partum: Item specific and relational encoding processes in recall and recognition.

PubMed

Spataro, Pietro; Saraulli, Daniele; Oriolo, Debora; Costanzi, Marco; Zanetti, Humberto; Cestari, Vincenzo; Rossi-Arnaud, Clelia

2016-08-01

It has been recently proposed that pregnant women would perform memory tasks by focusing more on item-specific processes and less on relational processing, compared to post-partum women (Mickes, Wixted, Shapiro & Scarff, ). The present cross-sectional study tested this hypothesis by directly manipulating the type of encoding employed in the study phase. Pregnant, post-partum and control women either rated the pleasantness of word meaning (which induced item-specific elaboration) or named the semantic category to which they belonged (which induced relational elaboration). Memory for the encoded words was later tested in free recall (which emphasizes relational processing) and in recognition (which emphasizes item-specific processing). In line with Mickes et al.'s () conclusions, pregnant women in the item-specific condition performed worse than post-partum women in the relational condition in free recall, but not in recognition. However, compared to the other two groups, pregnant women also exhibited lower recognition accuracy in the item-specific condition. Overall, these results confirm that pregnant women rely on relational encoding less than post-partum women, but additionally suggest that the former group might use item-specific processes less efficiently than post-partum and control women. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

Determination of orthotropic material properties by modal analysis

NASA Astrophysics Data System (ADS)

Lai, Junpeng

The methodology for determination of orthotropic material properties in plane stress condition will be presented. It is applied to orthotropic laminated plates like printed wiring boards. The first part of the thesis will focus on theories and methodologies. The static beam model and vibratory plate model is presented. The methods are validated by operating a series of test on aluminum. In the static tests, deflection and two directions of strain are measured, thus four of the properties will be identified: Ex, Ey, nuxy, nuyx. Moving on to dynamic test, the first ten modes' resonance frequencies are obtained. The technique of modal analysis is adopted. The measured data is processed by FFT and analyzed by curve fitting to extract natural frequencies and mode shapes. With the last material property to be determined, a finite element method using ANSYS is applied. Along with the identified material properties in static tests, and proper initial guess of the unknown shear modulus, an iterative process creates finite element model and conducts modal analysis with the updating model. When the modal analysis result produced by ANSYS matches the natural frequencies acquired by dynamic test, the process will halt. Then we obtained the last material property in plane stress condition.

SED16 autonomous star tracker night sky testing

NASA Astrophysics Data System (ADS)

Foisneau, Thierry; Piriou, Véronique; Perrimon, Nicolas; Jacob, Philippe; Blarre, Ludovic; Vilaire, Didier

2017-11-01

The SED16 is an autonomous multi-missions star tracker which delivers three axis satellite attitude in an inertial reference frame and the satellite angular velocity with no prior information. The qualification process of this star sensor includes five validation steps using optical star simulator, digitized image simulator and a night sky tests setup. The night sky testing was the final step of the qualification process during which all the functions of the star tracker were used in almost nominal conditions : Autonomous Acquisition of the attitude, Autonomous Tracking of ten stars. These tests were performed in Calern in the premises of the OCA (Observatoire de la Cote d'Azur). The test set-up and the test results are described after a brief review of the sensor main characteristics and qualification process.

A design of experiments test to define critical spray cleaning parameters for Brulin 815 GD and Jettacin cleaners

NASA Technical Reports Server (NTRS)

Keen, Jill M.; Evans, Kurt B.; Schiffman, Robert L.; Deweese, C. Darrell; Prince, Michael E.

1995-01-01

Experimental design testing was conducted to identify critical parameters of an aqueous spray process intended for cleaning solid rocket motor metal components (steel and aluminum). A two-level, six-parameter, fractional factorial matrix was constructed and conducted for two cleaners, Brulin 815 GD and Diversey Jettacin. The matrix parameters included cleaner temperature and concentration, wash density, wash pressure, rinse pressure, and dishwasher type. Other spray parameters: nozzle stand-off, rinse water temperature, wash and rinse time, dry conditions, and type of rinse water (deionized) were held constant. Matrix response testing utilized discriminating bond specimens (fracture energy and tensile adhesion strength) which represent critical production bond lines. Overall, Jettacin spray cleaning was insensitive to the range of conditions tested for all parameters and exhibited bond strengths significantly above the TCA test baseline for all bond lines tested. Brulin 815 was sensitive to cleaning temperature, but produced bond strengths above the TCA test baseline even at the lower temperatures. Ultimately, the experimental design database was utilized to recommend process parameter settings for future aqueous spray cleaning characterization work.

Super NiCd Open-Circuit Storage and Low Earth Orbit (LEO) Life Test Evaluation

NASA Technical Reports Server (NTRS)

Baer, Jean Marie; Hwang, Warren C.; Ang, Valerie J.; Hayden, Jeff; Rao, Gopalakrishna; Day, John H. (Technical Monitor)

2002-01-01

This presentation discusses Air Force tests performed on super NiCd cells to measure their performance under conditions simulating Low Earth Orbit (LEO) conditions. Super NiCd cells offer potential advantages over existing NiCd cell designs including advanced cell design with improved separator material and electrode making processes, but handling and storage requires active charging. These tests conclude that the super NiCd cells support generic Air Force qualifications for conventional LEO missions (up to five years duration) and that handling and storage may not actually require active charging as previously assumed. Topics covered include: Test Plan, Initial Characterization Tests, Open-Circuit Storage Tests, and post storage capacities.

Moral concerns increase attention and response monitoring during IAT performance: ERP evidence

PubMed Central

Ellemers, Naomi; Derks, Belle; Nieuwenhuis, Sander

2014-01-01

Previous research has revealed that people value morality as a more important person characteristic than competence. In this study, we tested whether people adjust their less explicit behavior more to moral than competence values. Participants performed an Implicit Association Test (IAT) that was either framed as a test of their morality or as a test of their competence. The behavioral results revealed a smaller IAT effect (i.e. a weaker negative implicit bias toward Muslims) in the morality condition than in the competence condition. Moreover, event-related potentials indicated increased social categorization of faces (as indexed by the N1 and P150) and enhanced conflict- and error monitoring (N450 and error-related negativity) in the morality condition compared to the competence condition. These findings indicate that an emphasis on morality can increase attentional and motivational processes that help to improve people’s task performance. PMID:23175679

Instructor Clarity and Student Motivation: Academic Performance as a Product of Students' Ability and Motivation to Process Instructional Material

ERIC Educational Resources Information Center

Bolkan, San; Goodboy, Alan K.; Kelsey, Dawn M.

2016-01-01

This study tested the notion that the effect of instructor clarity on learning is conditioned upon students' motivation. We randomly assigned 128 participants to a video of a clear or an unclear lecture and asked them to report their motivation to deeply process lecture material. Results indicated that even with clear instruction, test scores were…

Boundary conditioning of capacitive MEMS devices through fabrication methods and operating environments

NASA Astrophysics Data System (ADS)

Muthukumaran, Packirisamy; Stiharu, Ion G.; Bhat, Rama B.

2003-10-01

This paper presents and applies the concept of micro-boundary conditioning to the design synthesis of microsystems in order to quantify the influence of inherent limitations of the fabrication process and the operating conditions on both static and dynamic behavior of microsystems. The predicted results on the static and dynamic behavior of a capacitive MEMS device, fabricated through MUMPs process, under the influence of the fabrication limitation and operating environment are presented along with the test results. The comparison between the predicted and experimental results shows a good agreement.

Separation of plastics: The importance of kinetics knowledge in the evaluation of froth flotation.

PubMed

Censori, Matteo; La Marca, Floriana; Carvalho, M Teresa

2016-08-01

Froth flotation is a promising technique to separate polymers of similar density. The present paper shows the need for performing kinetic tests to evaluate and optimize the process. In the experimental study, batch flotation tests were performed on samples of ABS and PS. The floated product was collected at increasing flotation time. Two variables were selected for modification: the concentration of the depressor (tannic acid) and airflow rate. The former is associated with the chemistry of the process and the latter with the transport of particles. It was shown that, like mineral flotation, plastics flotation can be adequately assumed as a first order rate process. The results of the kinetic tests showed that the kinetic parameters change with the operating conditions. When the depressing action is weak and the airflow rate is low, the kinetic is fast. Otherwise, the kinetic is slow and a variable percentage of the plastics never floats. Concomitantly, the time at which the maximum difference in the recovery of the plastics in the floated product is attained changes with the operating conditions. The prediction of flotation results, process evaluation and comparisons should be done considering the process kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Orion Ground Test Article Water Impact Tests: Photogrammetric Evaluation of Impact Conditions

NASA Technical Reports Server (NTRS)

Vassilakos, Gregory J.; Mark, Stephen D.

2018-01-01

The Ground Test Article (GTA) is an early production version of the Orion Crew Module (CM). The structural design of the Orion CM is being developed based on LS-DYNA water landing simulations. As part of the process of confirming the accuracy of LS-DYNA water landing simulations, the GTA water impact test series was conducted at NASA Langley Research Center (LaRC) to gather data for comparison with simulations. The simulation of the GTA water impact tests requires the accurate determination of the impact conditions. To accomplish this, the GTA was outfitted with an array of photogrammetry targets. The photogrammetry system utilizes images from two cameras with a specialized tracking software to determine time histories for the 3-D coordinates of each target. The impact conditions can then be determined from the target location data.

Process material management in the Space Station environment

NASA Technical Reports Server (NTRS)

Perry, J. L.; Humphries, W. R.

1988-01-01

The Space Station will provide a unique facility for conducting material-processing and life-science experiments under microgravity conditions. These conditions place special requirements on the U.S. Laboratory for storing and transporting chemicals and process fluids, reclaiming water from selected experiments, treating and storing experiment wastes, and providing vacuum utilities. To meet these needs and provide a safe laboratory environment, the Process Material Management System (PMMS) is being developed. Preliminary design requirements and concepts related to the PMMS are addressed, and the MSFC PMMS breadboard test facility and a preliminary plan for validating the overall system design are discussed.

Taming Test Anxiety: The Activation of Failure-Related Concepts Enhances Cognitive Test Performance of Test-Anxious Students

ERIC Educational Resources Information Center

Tempel, Tobias; Neumann, Roland

2016-01-01

We investigated processes underlying performance decrements of highly test-anxious persons. Three experiments contrasted conditions that differed in the degree of activation of concepts related to failure. Participants memorized a list of words either containing words related to failure or containing no words related to failure in Experiment 1. In…

Wave Energy Prize -- Carderock Test Design and Rigging to Accommodate Diversity of Device Types

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driscoll, Frederick R

Wave Energy Prize Carderock Test Design and Rigging to Accommodate Diversity of Device Types presentation from the Water Power Technologies Office Peer Review, FY14-FY16. The challenge was to determine testing conditions, develop processing algorithms, and execute tests for equitable and consistent evaluation of different wave energy converter (WEC) technologies.

Evaluation of soil processing conditions on mineralizable C and N across a textural gradient

USDA-ARS?s Scientific Manuscript database

Soil biological activity is an important component of a well-functioning soil. Methodologies for estimating this process in soil vary due to a variety of theoretical, functional, and expediency considerations. We tested the effects of soil processing (sieve size), water delivery method (from top a...

[Potentialities of the vegetative resonance test for diagnostics of hyperplastic processes in vocal folds].

PubMed

Ukhankova, N I; Sotskaia, T Iu

2010-01-01

The objective of the present study was to evaluate potentialities of the vegetative resonance test (VRT) for the elucidation of metabolic aspects of the inflammatory process in different forms of chronic vocal fold hyperplasty. The proposed diagnostic criteria characterize the inflammatory process in the larynx, specific features of metabolism in patients presenting with catarrhal and oedematopolypous laryngitis, characteristic changes in oedematofibrous and fibrous polyps. The use of VRT allowed diagnostic criteria for precarcinogenic conditions in the larynx to be developed.

Performance evaluation approach for the supercritical helium cold circulators of ITER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaghela, H.; Sarkar, B.; Bhattacharya, R.

2014-01-29

The ITER project design foresees Supercritical Helium (SHe) forced flow cooling for the main cryogenic components, namely, the superconducting (SC) magnets and cryopumps (CP). Therefore, cold circulators have been selected to provide the required SHe mass flow rate to cope with specific operating conditions and technical requirements. Considering the availability impacts of such machines, it has been decided to perform evaluation tests of the cold circulators at operating conditions prior to the series production in order to minimize the project technical risks. A proposal has been conceptualized, evaluated and simulated to perform representative tests of the full scale SHe coldmore » circulators. The objectives of the performance tests include the validation of normal operating condition, transient and off-design operating modes as well as the efficiency measurement. A suitable process and instrumentation diagram of the test valve box (TVB) has been developed to implement the tests at the required thermodynamic conditions. The conceptual engineering design of the TVB has been developed along with the required thermal analysis for the normal operating conditions to support the performance evaluation of the SHe cold circulator.« less

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Scott; Baca, Georgina; O'Connor, Michael

2015-12-31

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is onmore » the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.« less

Mood-congruent attention and memory bias in dysphoria: Exploring the coherence among information-processing biases.

PubMed

Koster, Ernst H W; De Raedt, Rudi; Leyman, Lemke; De Lissnyder, Evi

2010-03-01

Recent studies indicate that depression is characterized by mood-congruent attention bias at later stages of information-processing. Moreover, depression has been associated with enhanced recall of negative information. The present study tested the coherence between attention and memory bias in dysphoria. Stable dysphoric (n = 41) and non-dysphoric (n = 41) undergraduates first performed a spatial cueing task that included negative, positive, and neutral words. Words were presented for 250 ms under conditions that allowed or prevented elaborate processing. Memory for the words presented in the cueing task was tested using incidental free recall. Dysphoric individuals exhibited an attention bias for negative words in the condition that allowed elaborate processing, with the attention bias for negative words predicting free recall of negative words. Results demonstrate the coherence of attention and memory bias in dysphoric individuals and provide suggestions on the influence of attention bias on further processing of negative material. 2009 Elsevier Ltd. All rights reserved.

The Effects of Aerobic Exercise and Gaming on Cognitive Performance.

PubMed

Douris, Peter C; Handrakis, John P; Apergis, Demitra; Mangus, Robert B; Patel, Rima; Limtao, Jessica; Platonova, Svetlana; Gregorio, Aladino; Luty, Elliot

2018-03-01

The purpose of our study was to investigate the effects of video gaming, aerobic exercise (biking), and the combination of these two activities on the domains of cognitive performance: selective attention, processing speed, and executive functioning. The study was a randomized clinical trial with 40 subjects (mean age 23.7 ± 1.8 years) randomized to one of four thirty-minute conditions: video gaming, biking, simultaneous gaming and biking, and a control condition. Cognitive performance was measured pre and post condition using the Stroop test and Trails B test. A mixed design was utilized. While video gaming, biking, simultaneous gaming and biking conditions improved selective attention and processing speed (p < 0.05), only the bike condition improved the highest order of cognitive performance, executive function (p < 0.01). There were no changes in cognitive performance for the control condition. Previous studies have shown that if tasks approach the limits of attentional capacity there is an increase in the overall chance for errors, known as the dual-task deficit. Simultaneous biking and gaming may have surpassed attentional capacity limits, ultimately increasing errors during the executive function tests of our cognitive performance battery. The results suggest that the fatiguing effects of a combined physically and mentally challenging task that extends after the exercise cessation may overcome the eventual beneficial cognitive effects derived from the physical exercise.

Evaluation of glucose controllers in virtual environment: methodology and sample application.

PubMed

Chassin, Ludovic J; Wilinska, Malgorzata E; Hovorka, Roman

2004-11-01

Adaptive systems to deliver medical treatment in humans are safety-critical systems and require particular care in both the testing and the evaluation phase, which are time-consuming, costly, and confounded by ethical issues. The objective of the present work is to develop a methodology to test glucose controllers of an artificial pancreas in a simulated (virtual) environment. A virtual environment comprising a model of the carbohydrate metabolism and models of the insulin pump and the glucose sensor is employed to simulate individual glucose excursions in subjects with type 1 diabetes. The performance of the control algorithm within the virtual environment is evaluated by considering treatment and operational scenarios. The developed methodology includes two dimensions: testing in relation to specific life style conditions, i.e. fasting, post-prandial, and life style (metabolic) disturbances; and testing in relation to various operating conditions, i.e. expected operating conditions, adverse operating conditions, and system failure. We define safety and efficacy criteria and describe the measures to be taken prior to clinical testing. The use of the methodology is exemplified by tuning and evaluating a model predictive glucose controller being developed for a wearable artificial pancreas focused on fasting conditions. Our methodology to test glucose controllers in a virtual environment is instrumental in anticipating the results of real clinical tests for different physiological conditions and for different operating conditions. The thorough testing in the virtual environment reduces costs and speeds up the development process.

Rule induction performance in amnestic mild cognitive impairment and Alzheimer's dementia: examining the role of simple and biconditional rule learning processes.

PubMed

Oosterman, Joukje M; Heringa, Sophie M; Kessels, Roy P C; Biessels, Geert Jan; Koek, Huiberdina L; Maes, Joseph H R; van den Berg, Esther

2017-04-01

Rule induction tests such as the Wisconsin Card Sorting Test require executive control processes, but also the learning and memorization of simple stimulus-response rules. In this study, we examined the contribution of diminished learning and memorization of simple rules to complex rule induction test performance in patients with amnestic mild cognitive impairment (aMCI) or Alzheimer's dementia (AD). Twenty-six aMCI patients, 39 AD patients, and 32 control participants were included. A task was used in which the memory load and the complexity of the rules were independently manipulated. This task consisted of three conditions: a simple two-rule learning condition (Condition 1), a simple four-rule learning condition (inducing an increase in memory load, Condition 2), and a complex biconditional four-rule learning condition-inducing an increase in complexity and, hence, executive control load (Condition 3). Performance of AD patients declined disproportionately when the number of simple rules that had to be memorized increased (from Condition 1 to 2). An additional increment in complexity (from Condition 2 to 3) did not, however, disproportionately affect performance of the patients. Performance of the aMCI patients did not differ from that of the control participants. In the patient group, correlation analysis showed that memory performance correlated with Condition 1 performance, whereas executive task performance correlated with Condition 2 performance. These results indicate that the reduced learning and memorization of underlying task rules explains a significant part of the diminished complex rule induction performance commonly reported in AD, although results from the correlation analysis suggest involvement of executive control functions as well. Taken together, these findings suggest that care is needed when interpreting rule induction task performance in terms of executive function deficits in these patients.

AISI/DOE Technology Roadmap Program: Cold Work Embrittlement of Interstitial Free Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

John T Bowker; Pierre Martin

2002-10-31

This work addresses the issues of measurement of secondary cold work embrittlement (SCWE) of an IF steel in deep-drawn parts using laboratory tests, and its correlation with real part fracture. It aimed at evaluating the influence of the steel chemistry and processing condition, microstructure, and test conditions, on SCWE as well as the effect of SCWE on fatigue properties. Size 6-in. cups produced with various draw ratios or trimmed at different heights were tested to determine the ductile-to-brittle-transition temperature (DBTT) as a function of strain. The 2-in. cup/expansion test, bend test and fracture of notched specimens were also used tomore » generate information complementary to that provided by the 6-inch cup/expansion test. The relationship between laboratory tests and fracture in real parts was established by testing large-scale parts. The fatigue behavior was investigated in the as-rolled and deep drawn (high stain) conditions, using prestrained specimens taken from the wall of a formed part.« less

[Optimization of extraction process for tannins from Geranium orientali-tibeticum by supercritical CO2 method].

PubMed

Xie, Song; Tong, Zhi-Ping; Tan, Rui; Liu, Xiao-Zhen

2014-08-01

In order to optimize extraction process conditions of tannins from Geranium orientali-tibeticum by supercritical CO2, the content of tannins was determined by phosphomolybdium tungsten acid-casein reaction, with extraction pressure, extraction temper- ature and extraction time as factors, the content of tannins from extract of G. orientali-tibeticum as index, technology conditions were optimized by orthogonal test. Optimum technology conditions were as follows: extraction pressure was 25 MPa, extraction temperature was 50 °C, extracted 1.5 h. The content of tannins in extract was 12.91 mg x g(-1), extract rate was 3.67%. The method established could be used for assay the contents of tannin in G. orientali-tibeticum. The circulated extraction was an effective extraction process that was stable and feasible, and that provides a way of the extraction process conditions of tannin from G. orientali-tibeticum.

Not Merely Experiential: Unconscious Thought Can Be Rational

PubMed Central

Garrison, Katie E.; Handley, Ian M.

2017-01-01

Individuals often form more reasonable judgments from complex information after a period of distraction vs. deliberation. This phenomenon has been attributed to sophisticated unconscious thought during the distraction period that integrates and organizes the information (Unconscious Thought Theory; Dijksterhuis and Nordgren, 2006). Yet, other research suggests that experiential processes are strengthened during the distraction (relative to deliberation) period, accounting for the judgment and decision benefit. We tested between these possibilities, hypothesizing that unconscious thought is distinct from experiential processes, and independently contributes to judgments and decisions during a distraction period. Using an established paradigm, Experiment 1 (N = 319) randomly induced participants into an experiential or rational mindset, after which participants received complex information describing three roommates to then consider consciously (i.e., deliberation) or unconsciously (i.e., distraction). Results revealed superior roommate judgments (but not choices) following distraction vs. deliberation, consistent with Unconscious Thought Theory. Mindset did not have an influence on roommate judgments. However, planned tests revealed a significant advantage of distraction only within the rational-mindset condition, which is contrary to the idea that experiential processing alone facilitates complex decision-making during periods of distraction. In a second experiment (N = 136), we tested whether effects of unconscious thought manifest for a complex analytical reasoning task for which experiential processing would offer no advantage. As predicted, participants in an unconscious thought condition outperformed participants in a control condition, suggesting that unconscious thought can be analytical. In sum, the current results support the existence of unconscious thinking processes that are distinct from experiential processes, and can be rational. Thus, the experiential vs. rational nature of a process might not cleanly delineate conscious and unconscious thought. PMID:28729844

Not Merely Experiential: Unconscious Thought Can Be Rational.

PubMed

Garrison, Katie E; Handley, Ian M

2017-01-01

Individuals often form more reasonable judgments from complex information after a period of distraction vs. deliberation. This phenomenon has been attributed to sophisticated unconscious thought during the distraction period that integrates and organizes the information (Unconscious Thought Theory; Dijksterhuis and Nordgren, 2006). Yet, other research suggests that experiential processes are strengthened during the distraction (relative to deliberation) period, accounting for the judgment and decision benefit. We tested between these possibilities, hypothesizing that unconscious thought is distinct from experiential processes, and independently contributes to judgments and decisions during a distraction period. Using an established paradigm, Experiment 1 ( N = 319) randomly induced participants into an experiential or rational mindset, after which participants received complex information describing three roommates to then consider consciously (i.e., deliberation) or unconsciously (i.e., distraction). Results revealed superior roommate judgments (but not choices) following distraction vs. deliberation, consistent with Unconscious Thought Theory. Mindset did not have an influence on roommate judgments. However, planned tests revealed a significant advantage of distraction only within the rational-mindset condition, which is contrary to the idea that experiential processing alone facilitates complex decision-making during periods of distraction. In a second experiment ( N = 136), we tested whether effects of unconscious thought manifest for a complex analytical reasoning task for which experiential processing would offer no advantage. As predicted, participants in an unconscious thought condition outperformed participants in a control condition, suggesting that unconscious thought can be analytical. In sum, the current results support the existence of unconscious thinking processes that are distinct from experiential processes, and can be rational. Thus, the experiential vs. rational nature of a process might not cleanly delineate conscious and unconscious thought.

Real-time Enhancement, Registration, and Fusion for an Enhanced Vision System

NASA Technical Reports Server (NTRS)

Hines, Glenn D.; Rahman, Zia-ur; Jobson, Daniel J.; Woodell, Glenn A.

2006-01-01

Over the last few years NASA Langley Research Center (LaRC) has been developing an Enhanced Vision System (EVS) to aid pilots while flying in poor visibility conditions. The EVS captures imagery using two infrared video cameras. The cameras are placed in an enclosure that is mounted and flown forward-looking underneath the NASA LaRC ARIES 757 aircraft. The data streams from the cameras are processed in real-time and displayed on monitors on-board the aircraft. With proper processing the camera system can provide better-than-human-observed imagery particularly during poor visibility conditions. However, to obtain this goal requires several different stages of processing including enhancement, registration, and fusion, and specialized processing hardware for real-time performance. We are using a real-time implementation of the Retinex algorithm for image enhancement, affine transformations for registration, and weighted sums to perform fusion. All of the algorithms are executed on a single TI DM642 digital signal processor (DSP) clocked at 720 MHz. The image processing components were added to the EVS system, tested, and demonstrated during flight tests in August and September of 2005. In this paper we briefly discuss the EVS image processing hardware and algorithms. We then discuss implementation issues and show examples of the results obtained during flight tests.

Signal Processing for Determining Water Height in Steam Pipes with Dynamic Surface Conditions

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh; Lee, Hyeong Jae; Bar-Cohen, Yoseph

2015-01-01

An enhanced signal processing method based on the filtered Hilbert envelope of the auto-correlation function of the wave signal has been developed to monitor the height of condensed water through the steel wall of steam pipes with dynamic surface conditions. The developed signal processing algorithm can also be used to estimate the thickness of the pipe to determine the cut-off frequency for the low pass filter frequency of the Hilbert Envelope. Testing and analysis results by using the developed technique for dynamic surface conditions are presented. A multiple array of transducers setup and methodology are proposed for both the pulse-echo and pitch-catch signals to monitor the fluctuation of the water height due to disturbance, water flow, and other anomaly conditions.

The emotional startle effect is disrupted by a concurrent working memory task.

PubMed

King, Rosemary; Schaefer, Alexandre

2011-02-01

Working memory (WM) processes are often thought to play an important role in the cognitive regulation of negative emotions. However, little is known about how they influence emotional processing. We report two experiments that tested whether a concurrent working memory task could modulate the emotional startle eyeblink effect, a well-known index of emotional processing. In both experiments, emotionally negative and neutral pictures were viewed in two conditions: a "cognitive load" (CL) condition, in which participants had to actively maintain information in working memory (WM) while viewing the pictures, and a control "no load" (NL) condition. Picture-viewing instructions were identical across CL and NL. In both experiments, results showed a significant reduction of the emotional modulation of the startle eyeblink reflex in the CL condition compared to the NL condition. These findings suggest that a concurrent WM task disrupts emotional processing even when participants are directing visual focus on emotionally relevant information. Copyright © 2010 Society for Psychophysiological Research.

ETV REPORT AND VERIFICATION STATEMENT - KASELCO POSI-FLO ELECTROCOAGULATION TREATMENT SYSTEM

EPA Science Inventory

The Kaselco Electrocoagulation Treatment System (Kaselco system) in combination with an ion exchange polishing system was tested, under actual production conditions, processing metal finishing wastewater at Gull Industries in Houston, Texas. The verification test evaluated the a...

Deep Learning-Based Noise Reduction Approach to Improve Speech Intelligibility for Cochlear Implant Recipients.

PubMed

Lai, Ying-Hui; Tsao, Yu; Lu, Xugang; Chen, Fei; Su, Yu-Ting; Chen, Kuang-Chao; Chen, Yu-Hsuan; Chen, Li-Ching; Po-Hung Li, Lieber; Lee, Chin-Hui

2018-01-20

We investigate the clinical effectiveness of a novel deep learning-based noise reduction (NR) approach under noisy conditions with challenging noise types at low signal to noise ratio (SNR) levels for Mandarin-speaking cochlear implant (CI) recipients. The deep learning-based NR approach used in this study consists of two modules: noise classifier (NC) and deep denoising autoencoder (DDAE), thus termed (NC + DDAE). In a series of comprehensive experiments, we conduct qualitative and quantitative analyses on the NC module and the overall NC + DDAE approach. Moreover, we evaluate the speech recognition performance of the NC + DDAE NR and classical single-microphone NR approaches for Mandarin-speaking CI recipients under different noisy conditions. The testing set contains Mandarin sentences corrupted by two types of maskers, two-talker babble noise, and a construction jackhammer noise, at 0 and 5 dB SNR levels. Two conventional NR techniques and the proposed deep learning-based approach are used to process the noisy utterances. We qualitatively compare the NR approaches by the amplitude envelope and spectrogram plots of the processed utterances. Quantitative objective measures include (1) normalized covariance measure to test the intelligibility of the utterances processed by each of the NR approaches; and (2) speech recognition tests conducted by nine Mandarin-speaking CI recipients. These nine CI recipients use their own clinical speech processors during testing. The experimental results of objective evaluation and listening test indicate that under challenging listening conditions, the proposed NC + DDAE NR approach yields higher intelligibility scores than the two compared classical NR techniques, under both matched and mismatched training-testing conditions. When compared to the two well-known conventional NR techniques under challenging listening condition, the proposed NC + DDAE NR approach has superior noise suppression capabilities and gives less distortion for the key speech envelope information, thus, improving speech recognition more effectively for Mandarin CI recipients. The results suggest that the proposed deep learning-based NR approach can potentially be integrated into existing CI signal processors to overcome the degradation of speech perception caused by noise.

What's New with Newborn Screening

ERIC Educational Resources Information Center

Exceptional Parent, 2008

2008-01-01

Newborn screening is the process of testing and screening newborns shortly after birth for certain, potentially dangerous, conditions and/or impairments--conditions that include everything from inborn errors of metabolism and other genetic disorders to hearing impairment. Early detection through newborn screening is paramount, often allowing the…

The MIST /MIUS Integration and Subsystems Test/ laboratory - A testbed for the MIUS /Modular Integrated Utility System/ program

NASA Technical Reports Server (NTRS)

Beckham, W. S., Jr.; Keune, F. A.

1974-01-01

The MIUS (Modular Integrated Utility System) concept is to be an energy-conserving, economically feasible, integrated community utility system to provide five necessary services: electricity generation, space heating and air conditioning, solid waste processing, liquid waste processing, and residential water purification. The MIST (MIUS Integration and Subsystem Test) integrated system testbed constructed at the Johnson Space Center in Houston includes subsystems for power generation, heating, ventilation, and air conditioning (HVAC), wastewater management, solid waste management, and control and monitoring. The key design issues under study include thermal integration and distribution techniques, thermal storage, integration of subsystems controls and displays, incinerator performance, effluent characteristics, and odor control.

78 FR 65145 - Federal Agricultural Mortgage Corporation Funding and Fiscal Affairs; Farmer Mac Capital Planning

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... capital base and promote best practices for capital adequacy planning and stress testing. We view high... minimum supervisory standards for the capital planning process, including stress testing, (ii) describes... stress tests to ensure they are able to sustain financial soundness under adverse market conditions. In...

Testing and evaluation of light ablation decontamination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Demmer, R.L.; Ferguson, R.L.

1994-10-01

This report details the testing and evaluation of light ablation decontamination. It details WINCO contracted research and application of light ablation efforts by Ames Laboratory. Tests were conducted with SIMCON (simulated contamination) coupons and REALCON (actual radioactive metal coupons) under controlled conditions to compare cleaning effectiveness, speed and application to plant process type equipment.

Treated and Untreated foam core particleboards with intumescent veneer

Treesearch

Mark A. Dietenberger; Ali Shalbafan; Johannes Welling; Charles Boardman

2013-01-01

The effectiveness of treatments for the surface layer of novel foam core particleboards was evaluated by means of Cone calorimeter tests, Foam cote particleboards with variations of surface layer treatment, adhesives, and surface layer thicknesses under similar processing conditions were used to produce the test specimen for the Cone calorimeter tests. Ignitability,...

Cone Calorimeter Analysis of FRT Intumescent and Untreated Foam Core Particleboards

Treesearch

Mark A. Dietenberger; Ali Shalbafan; Johannes Welling; Charles Boardman

2012-01-01

The effectiveness of treatments of the surface layer of novel foam core particleboards were evaluated by means of Cone calorimeter tests. Foam core particleboards with variations of surface layer treatment, adhesives and surface layer thicknesses under similar processing conditions were used to produce the test specimen for the Cone calorimeter tests. Ignitability,...

The effectiveness of CCDSR learning model to improve skills of creating lesson plan and worksheet science process skill (SPS) for pre-service physics teacher

NASA Astrophysics Data System (ADS)

Limatahu, I.; Sutoyo, S.; Wasis; Prahani, B. K.

2018-03-01

In the previous research, CCDSR (Condition, Construction, Development, Simulation, and Reflection) learning model has been developed to improve science process skills for pre-service physics teacher. This research is aimed to analyze the effectiveness of CCDSR learning model towards the improvement skills of creating lesson plan and worksheet of Science Process Skill (SPS) for pre-service physics teacher in academic year 2016/2017. This research used one group pre-test and post-test design on 12 pre-service physics teacher at Physics Education, University of Khairun. Data collection was conducted through test and observation. Creating lesson plan and worksheet SPS skills of pre-service physics teacher measurement were conducted through Science Process Skill Evaluation Sheet (SPSES). The data analysis technique was done by Wilcoxon t-test and n-gain. The CCDSR learning model consists of 5 phases, including (1) Condition, (2) Construction, (3) Development, (4) Simulation, and (5) Reflection. The results showed that there was a significant increase in creating lesson plan and worksheet SPS skills of pre-service physics teacher at α = 5% and n-gain average of moderate category. Thus, the CCDSR learning model is effective for improving skills of creating lesson plan and worksheet SPS for pre-service physics teacher.

One process is not enough! A speed-accuracy tradeoff study of recognition memory.

PubMed

Boldini, Angela; Russo, Riccardo; Avons, S E

2004-04-01

Speed-accuracy tradeoff (SAT) methods have been used to contrast single- and dual-process accounts of recognition memory. In these procedures, subjects are presented with individual test items and are required to make recognition decisions under various time constraints. In this experiment, we presented word lists under incidental learning conditions, varying the modality of presentation and level of processing. At test, we manipulated the interval between each visually presented test item and a response signal, thus controlling the amount of time available to retrieve target information. Study-test modality match had a beneficial effect on recognition accuracy at short response-signal delays (< or =300 msec). Conversely, recognition accuracy benefited more from deep than from shallow processing at study only at relatively long response-signal delays (> or =300 msec). The results are congruent with views suggesting that both fast familiarity and slower recollection processes contribute to recognition memory.

Drinkers’ memory bias for alcohol picture cues in explicit and implicit memory tasks

PubMed Central

Nguyen-Louie, Tam T.; Buckman, Jennifer F.; Ray, Suchismita

2016-01-01

Background Alcohol cues can bias attention and elicit emotional reactions, especially in drinkers. Yet, little is known about how alcohol cues affect explicit and implicit memory processes, and how memory for alcohol cues is affected by acute alcohol intoxication. Methods Young adult participants (N=161) were randomly assigned to alcohol, placebo, or control beverage conditions. Following beverage consumption, they were shown neutral, emotional and alcohol-related pictures cues. Participants then completed free recall and repetition priming tasks to test explicit and implicit memory, respectively, for picture cues. Average blood alcohol concentration for the alcohol group was 74 ± 13 mg/dl when memory testing began. Two mixed linear model analyses were conducted to examine the effects of beverage condition, picture cue type, and their interaction on explicit and implicit memory. Results Picture cue type and beverage condition each significantly affected explicit recall of picture cues, whereas only picture cue type significantly influenced repetition priming. Individuals in the alcohol condition recalled significantly fewer pictures than those in other conditions, regardless of cue type. Both free recall and repetition priming were greater for emotional and alcohol-related cues compared to neutral picture cues. No interaction effects were detected. Conclusions Young adult drinkers showed enhanced explicit and implicit memory processing of alcohol cues compared to emotionally neutral cues. This enhanced processing for alcohol cues was on par with that seen for positive emotional cues. Acute alcohol intoxication did not alter this preferential memory processing for alcohol cues over neutral cues. PMID:26811126

Assessment of the influence of surface finishing and weld joints on the corrosion/oxidation behaviour of stainless steels in lead bismuth eutectic

NASA Astrophysics Data System (ADS)

Martín-Muñoz, F. J.; Soler-Crespo, L.; Gómez-Briceño, D.

2011-09-01

The objective of this paper is to gain some insight into the influence of the surface finishing in the oxidation/corrosion behaviour of 316L and T91 steels in lead bismuth eutectic (LBE). Specimens of both materials with different surface states were prepared (as-received, grinded, grinded and polished, and electrolitically polished) and oxidation tests were carried out at 775 and 825 K from 100 to 2000 h for two different oxygen concentrations and for H 2/H 2O molar ratios of 3 and 0.03. The general conclusion for these tests is that the effect of surface finishing on the corrosion/protection processes is not significant under the tested conditions. In addition the behaviour of weld joints, T91-T91 Tungsten Inert Gas (TIG) and T91-316L have been also studied under similar conditions. The conclusions are that, whereas T91-T91 welded joint shows the same corrosion properties as the parent materials for the conditions tested, AISI 316L-T91 welded joint, present an important dissolution over seam area that it associated to the electrode 309S used for the fabrication process.

Space Power Facility Reverberation Chamber Calibration Report

NASA Technical Reports Server (NTRS)

Lewis, Catherine C.; Dolesh, Robert J.; Garrett, Michael J.

2014-01-01

This document describes the process and results of calibrating the Space Environmental Test EMI Test facility at NASA Plum Brook Space Power Facility according to the specifications of IEC61000-4-21 for susceptibility testing from 100 MHz to 40 GHz. The chamber passed the field uniformity test, in both the empty and loaded conditions, making it the world's largest Reverberation Chamber.

POST-RETRIEVAL PROPRANOLOL TREATMENT DOES NOT MODULATE RECONSOLIDATION OR EXTINCTION OF ETHANOL-INDUCED CONDITIONED PLACE PREFERENCE

PubMed Central

Font, Laura; Cunningham, Christopher L.

2012-01-01

The reconsolidation hypothesis posits that established emotional memories, when reactivated, become labile and susceptible to disruption. Post-retrieval injection of propranolol (PRO), a nonspecific β-adrenergic receptor antagonist, impairs subsequent retention performance of a cocaine- and a morphine-induced conditioned place preference (CPP), implicating the noradrenergic system in the reconsolidation processes of drug-seeking behavior. An important question is whether post-retrieval PRO disrupts memory for the drug-cue associations, or instead interferes with extinction. In the present study, we evaluated the role of the β-adrenergic system on the reconsolidation and extinction of ethanol-induced CPP. Male DBA/2J mice were trained using a weak or a strong conditioning procedure, achieved by varying the ethanol conditioning dose (1 or 2 g/kg) and the number of ethanol trials (2 or 4). After acquisition of ethanol CPP, animals were given a single post-retrieval injection of PRO (0, 10 or 30 mg/kg) and tested for memory reconsolidation 24 h later. Also, after the first reconsolidation test, mice received 18 additional 15-min choice extinction tests in which PRO was injected immediately after every test. Contrary to the prediction of the reconsolidation hypothesis, a single PRO injection after the retrieval test did not modify subsequent memory retention. In addition, repeated post-retrieval administration of PRO did not interfere with extinction of CPP in mice. Overall, our data suggest that the β-adrenergic receptor does not modulate the associative processes underlying ethanol CPP. PMID:22285323

The Development of a Microbial Challenge Test with Acholeplasma laidlawii To Rate Mycoplasma-Retentive Filters by Filter Manufacturers.

PubMed

Folmsbee, Martha; Lentine, Kerry Roche; Wright, Christine; Haake, Gerhard; Mcburnie, Leesa; Ashtekar, Dilip; Beck, Brian; Hutchison, Nick; Okhio-Seaman, Laura; Potts, Barbara; Pawar, Vinayak; Windsor, Helena

2014-01-01

Mycoplasma are bacteria that can penetrate 0.2 and 0.22 μm rated sterilizing-grade filters and even some 0.1 μm rated filters. Primary applications for mycoplasma filtration include large scale mammalian and bacterial cell culture media and serum filtration. The Parenteral Drug Association recognized the absence of standard industry test parameters for testing and classifying 0.1 μm rated filters for mycoplasma clearance and formed a task force to formulate consensus test parameters. The task force established some test parameters by common agreement, based upon general industry practices, without the need for additional testing. However, the culture medium and incubation conditions, for generating test mycoplasma cells, varied from filter company to filter company and was recognized as a serious gap by the task force. Standardization of the culture medium and incubation conditions required collaborative testing in both commercial filter company laboratories and in an Independent laboratory (Table I). The use of consensus test parameters will facilitate the ultimate cross-industry goal of standardization of 0.1 μm filter claims for mycoplasma clearance. However, it is still important to recognize filter performance will depend on the actual conditions of use. Therefore end users should consider, using a risk-based approach, whether process-specific evaluation of filter performance may be warranted for their application. Mycoplasma are small bacteria that have the ability to penetrate sterilizing-grade filters. Filtration of large-scale mammalian and bacterial cell culture media is an example of an industry process where effective filtration of mycoplasma is required. The Parenteral Drug Association recognized the absence of industry standard test parameters for evaluating mycoplasma clearance filters by filter manufacturers and formed a task force to formulate such a consensus among manufacturers. The use of standardized test parameters by filter manufacturers, including the preparation of the culture broth, will facilitate the end user's evaluation of the mycoplasma clearance claims provided by filter vendors. However, it is still important to recognize filter performance will depend on the actual conditions of use; therefore end users should consider, using a risk-based approach, whether process-specific evaluation of filter performance may be warranted for their application. © PDA, Inc. 2014.

Study on load test of 100m cross-reinforced deck type concrete box arch bridge

NASA Astrophysics Data System (ADS)

Shi, Jing Xian; Cheng, Ying Jie

2018-06-01

Found in the routine quality inspection of highway bridge that many vertical fractures on the main beam (10mT beam) of the steel reinforced concrete arch bridge near the hydropower station. In order to grasp the bearing capacity of this bridge under working conditions with cracks, the static load and dynamic load test of box arch bridge are carried out. The Midas civil theory is calculated by using the special plate trailer - 300 as the calculation load, and the deflection and stress of the critical section are tested by the equivalent cloth load in the test vehicle. The pulsation test, obstacles and no obstacle driving test were carried out. Experimental results show that the bridge under the condition of the test loads is in safe condition, main bearing component of the strength and stiffness meet the design requirements, the crack width does not increase, in the process of loading bridge overall work performance is good.

Real-time Enhancement, Registration, and Fusion for a Multi-Sensor Enhanced Vision System

NASA Technical Reports Server (NTRS)

Hines, Glenn D.; Rahman, Zia-ur; Jobson, Daniel J.; Woodell, Glenn A.

2006-01-01

Over the last few years NASA Langley Research Center (LaRC) has been developing an Enhanced Vision System (EVS) to aid pilots while flying in poor visibility conditions. The EVS captures imagery using two infrared video cameras. The cameras are placed in an enclosure that is mounted and flown forward-looking underneath the NASA LaRC ARIES 757 aircraft. The data streams from the cameras are processed in real-time and displayed on monitors on-board the aircraft. With proper processing the camera system can provide better-than- human-observed imagery particularly during poor visibility conditions. However, to obtain this goal requires several different stages of processing including enhancement, registration, and fusion, and specialized processing hardware for real-time performance. We are using a real-time implementation of the Retinex algorithm for image enhancement, affine transformations for registration, and weighted sums to perform fusion. All of the algorithms are executed on a single TI DM642 digital signal processor (DSP) clocked at 720 MHz. The image processing components were added to the EVS system, tested, and demonstrated during flight tests in August and September of 2005. In this paper we briefly discuss the EVS image processing hardware and algorithms. We then discuss implementation issues and show examples of the results obtained during flight tests. Keywords: enhanced vision system, image enhancement, retinex, digital signal processing, sensor fusion

[Preparation of bioindicators for controlling the efficacy of sterilization processes].

PubMed

Kalinina, N M; Tikhonova, A S; Motina, G L; Chaĭkovskaia, S M; Semenov, S M

1983-08-01

A test microbe for the control of the efficacy of vacuum steam sterilization was selected. Conditions for the spore cultivation were developed. The optimal bioindicator composition, test microbe loading, nutrient medium, pH indicator, carbohydrates and a carrier were defined.

Anaerobic Biodegradation of Detergent Surfactants

PubMed Central

Merrettig-Bruns, Ute; Jelen, Erich

2009-01-01

Detergent surfactants can be found in wastewater in relevant concentrations. Most of them are known as ready degradable under aerobic conditions, as required by European legislation. Far fewer surfactants have been tested so far for biodegradability under anaerobic conditions. The natural environment is predominantly aerobic, but there are some environmental compartments such as river sediments, sub-surface soil layer and anaerobic sludge digesters of wastewater treatment plants which have strictly anaerobic conditions. This review gives an overview on anaerobic biodegradation processes, the methods for testing anaerobic biodegradability, and the anaerobic biodegradability of different detergent surfactant types (anionic, nonionic, cationic, amphoteric surfactants).

Application of a Parallelizable Perfusion Bioreactor for Physiologic 3D Cell Culture.

PubMed

Egger, Dominik; Spitz, Sarah; Fischer, Monica; Handschuh, Stephan; Glösmann, Martin; Friemert, Benedikt; Egerbacher, Monika; Kasper, Cornelia

2017-01-01

It is crucial but challenging to keep physiologic conditions during the cultivation of 3D cell scaffold constructs for the optimization of 3D cell culture processes. Therefore, we demonstrate the benefits of a recently developed miniaturized perfusion bioreactor together with a specialized incubator system that allows for the cultivation of multiple samples while screening different conditions. Hence, a decellularized bone matrix was tested towards its suitability for 3D osteogenic differentiation under flow perfusion conditions. Subsequently, physiologic shear stress and hydrostatic pressure (HP) conditions were optimized for osteogenic differentiation of human mesenchymal stem cells (MSCs). X-ray computed microtomography and scanning electron microscopy (SEM) revealed a closed cell layer covering the entire matrix. Osteogenic differentiation assessed by alkaline phosphatase activity and SEM was found to be increased in all dynamic conditions. Furthermore, screening of different fluid shear stress (FSS) conditions revealed 1.5 mL/min (equivalent to ∼10 mPa shear stress) to be optimal. However, no distinct effect of HP compared to flow perfusion without HP on osteogenic differentiation was observed. Notably, throughout all experiments, cells cultivated under FSS or HP conditions displayed increased osteogenic differentiation, which underlines the importance of physiologic conditions. In conclusion, the bioreactor system was used for biomaterial testing and to develop and optimize a 3D cell culture process for the osteogenic differentiation of MSCs. Due to its versatility and higher throughput efficiency, we hypothesize that this bioreactor/incubator system will advance the development and optimization of a variety of 3D cell culture processes. © 2017 S. Karger AG, Basel.

Rigid Facial Motion Influences Featural, But Not Holistic, Face Processing

PubMed Central

Xiao, Naiqi; Quinn, Paul C.; Ge, Liezhong; Lee, Kang

2012-01-01

We report three experiments in which we investigated the effect of rigid facial motion on face processing. Specifically, we used the face composite effect to examine whether rigid facial motion influences primarily featural or holistic processing of faces. In Experiments 1, 2, and 3, participants were first familiarized with dynamic displays in which a target face turned from one side to another; then at test, participants judged whether the top half of a composite face (the top half of the target face aligned or misaligned with the bottom half of a foil face) belonged to the target face. We compared performance in the dynamic condition to various static control conditions in Experiments 1, 2, and 3, which differed from each other in terms of the display order of the multiple static images or the inter stimulus interval (ISI) between the images. We found that the size of the face composite effect in the dynamic condition was significantly smaller than that in the static conditions. In other words, the dynamic face display influenced participants to process the target faces in a part-based manner and consequently their recognition of the upper portion of the composite face at test became less interfered with by the aligned lower part of the foil face. The findings from the present experiments provide the strongest evidence to date to suggest that the rigid facial motion mainly influences facial featural, but not holistic, processing. PMID:22342561

Reinforcement in an in Vitro Analog of Appetitive Classical Conditioning of Feeding Behavior in "Aplysia": Blockade by a Dopamine Antagonist

ERIC Educational Resources Information Center

Reyes, Fredy D.; Mozzachiodi, Riccardo; Baxter, Douglas A.; Byrne, John H.

2005-01-01

In a recently developed in vitro analog of appetitive classical conditioning of feeding in "Aplysia," the unconditioned stimulus (US) was electrical stimulation of the esophageal nerve (En). This nerve is rich in dopamine (DA)-containing processes, which suggests that DA mediates reinforcement during appetitive conditioning. To test this…

Analysis and Synthesis of Adaptive Neural Elements and Assembles

DTIC Science & Technology

1993-09-30

of an Aplysia sensory neuron was developed that reflects the subcellular processes underlying activity-dependent neuromodulation . This single- Page -3... neuromodulation learning rule could simulate some higher-order features of classical conditioning, such second-order conditioning and blocking. During the...reporting period, simulations were used to test the hypothesis that activity-dependent neuromodulation could also support operant conditioning. A

Review of Air Vitiation Effects on Scramjet Ignition and Flameholding Combustion Processes

NASA Technical Reports Server (NTRS)

Pellett, G. L.; Bruno, Claudio; Chinitz, W.

2002-01-01

This paper offers a detailed review and analysis of more than 100 papers on the physics and chemistry of scramjet ignition and flameholding combustion processes, and the known effects of air vitiation on these processes. The paper attempts to explain vitiation effects in terms of known chemical kinetics and flame propagation phenomena. Scaling methodology is also examined, and a highly simplified Damkoehler scaling technique based on OH radical production/destruction is developed to extrapolate ground test results, affected by vitiation, to flight testing conditions. The long term goal of this effort is to help provide effective means for extrapolating ground test data to flight, and thus to reduce the time and expense of both ground and flight testing.

Dynamic metrology and data processing for precision freeform optics fabrication and testing

NASA Astrophysics Data System (ADS)

Aftab, Maham; Trumper, Isaac; Huang, Lei; Choi, Heejoo; Zhao, Wenchuan; Graves, Logan; Oh, Chang Jin; Kim, Dae Wook

2017-06-01

Dynamic metrology holds the key to overcoming several challenging limitations of conventional optical metrology, especially with regards to precision freeform optical elements. We present two dynamic metrology systems: 1) adaptive interferometric null testing; and 2) instantaneous phase shifting deflectometry, along with an overview of a gradient data processing and surface reconstruction technique. The adaptive null testing method, utilizing a deformable mirror, adopts a stochastic parallel gradient descent search algorithm in order to dynamically create a null testing condition for unknown freeform optics. The single-shot deflectometry system implemented on an iPhone uses a multiplexed display pattern to enable dynamic measurements of time-varying optical components or optics in vibration. Experimental data, measurement accuracy / precision, and data processing algorithms are discussed.

Neural basis of uncertain cue processing in trait anxiety.

PubMed

Zhang, Meng; Ma, Chao; Luo, Yanyan; Li, Ji; Li, Qingwei; Liu, Yijun; Ding, Cody; Qiu, Jiang

2016-02-19

Individuals with high trait anxiety form a non-clinical group with a predisposition for an anxiety-related bias in emotional and cognitive processing that is considered by some to be a prerequisite for psychiatric disorders. Anxious individuals tend to experience more worry under uncertainty, and processing uncertain information is an important, but often overlooked factor in anxiety. So, we decided to explore the brain correlates of processing uncertain information in individuals with high trait anxiety using the learn-test paradigm. Behaviorally, the percentages on memory test and the likelihood ratios of identifying novel stimuli under uncertainty were similar to the certain fear condition, but different from the certain neutral condition. The brain results showed that the visual cortex, bilateral fusiform gyrus, and right parahippocampal gyrus were active during the processing of uncertain cues. Moreover, we found that trait anxiety was positively correlated with the BOLD signal of the right parahippocampal gyrus during the processing of uncertain cues. No significant results were found in the amygdala during uncertain cue processing. These results suggest that memory retrieval is associated with uncertain cue processing, which is underpinned by over-activation of the right parahippocampal gyrus, in individuals with high trait anxiety.

Effect of natural weathering conditions on the dynamic behavior of woven aramid composites

NASA Astrophysics Data System (ADS)

Kaya, A. I.; Kısa, M.; Özen, M.

2018-02-01

In this study, aging of woven aramid/epoxy composites under different natural conditions were studied. Composite beams were manufactured by Vacuum Assisted Resin Infusion Method (VARIM). Composites were cut into specimen according to ASTM D3039 and vibration tests. Elastic moduli of reference composites were found according to ASTM D3039 standard. Validation of methodology was performed numerically in Ansys software before aging process. An algorithm, which is predicated on FFT (Fast Fourier Transforms), was composed in Matlab to process output of vibration analysis data so as to identify natural frequencies of beams. Composites were aged for 12 months and various natural weathering aging conditions effects on woven aramid composite beams were surveyed through vibration analysis with 3 months interval. Five specimens of woven aramid beams were considered for dynamic tests and effect of aging on first three natural frequencies were determined.

Oxygen transfer in a full-depth biological aerated filter.

PubMed

Stenstrom, Michael K; Rosso, Diego; Melcer, Henryk; Appleton, Ron; Occiano, Victor; Langworthy, Alan; Wong, Pete

2008-07-01

The City of San Diego, California, evaluated the performance capabilities of biological aerated filters (BAFs) at the Point Loma Wastewater Treatment Plant. The City conducted a 1-year pilot-plant evaluation of BAF technology supplied by two BAF manufacturers. This paper reports on the first independent oxygen-transfer test of BAFs at full depth using the offgas method. The tests showed process-water oxygen-transfer efficiencies of 1.6 to 5.8%/m (0.5 to 1.8%/ft) and 3.9 to 7.9%/m (1.2 to 2.4%/ft) for the two different pilot plants, at their nominal design conditions. Mass balances using chemical oxygen demand and dissolved organic carbon corroborated the transfer rates. Rates are higher than expected from fine-pore diffusers for similar process conditions and depths and clean-water conditions for the same column and are mostly attributed to extended bubble retention time resulting from interactions with the media and biofilm.

Marital Status as a Moderating Factor in the Process of Disablement.

PubMed

Kail, Ben Lennox

2016-02-01

To test current marital status as a moderator on the influence of depressive symptoms and chronic conditions on subsequent functional limitations. Data come from the Health and Retirement Study (HRS; 1998-2010). Hierarchal linear modeling models tested differences in functional limitations among a sample of 20,215 people. At baseline, married people suffered from fewer subsequent functional limitations than the unmarried. Moreover, limited evidence suggests the influence of depressive symptoms was greater for the married than the unmarried; however, the influence of chronic conditions was consistently attenuated for married people. Accounting for differences in prior health, work, socioeconomic status, and health behaviors did not explain the moderating influence of marital status on the associations between symptoms of depression and chronic conditions with functional limitations. This research highlights the need to identify potential modifiers that may help disrupt the process of disablement among both the married and the unmarried alike. © The Author(s) 2015.

Anaerobic co-digestion of winery waste and waste activated sludge: assessment of process feasibility.

PubMed

Da Ros, C; Cavinato, C; Cecchi, F; Bolzonella, D

2014-01-01

In this study the anaerobic co-digestion of wine lees together with waste activated sludge in mesophilic and thermophilic conditions was tested at pilot scale. Three organic loading rates (OLRs 2.8, 3.3 and 4.5 kgCOD/m(3)d) and hydraulic retention times (HRTs 21, 19 and 16 days) were applied to the reactors, in order to evaluate the best operational conditions for the maximization of the biogas yields. The addition of lee to sludge determined a higher biogas production: the best yield obtained was 0.40 Nm(3)biogas/kgCODfed. Because of the high presence of soluble chemical oxygen demand (COD) and polyphenols in wine lees, the best results in terms of yields and process stability were obtained when applying the lowest of the three organic loading rates tested together with mesophilic conditions.

WADeG Cell Phone

DOE Office of Scientific and Technical Information (OSTI.GOV)

2009-09-01

The on cell phone software captures the images from the CMOS camera periodically, stores the pictures, and periodically transmits those images over the cellular network to the server. The cell phone software consists of several modules: CamTest.cpp, CamStarter.cpp, StreamIOHandler .cpp, and covertSmartDevice.cpp. The camera application on the SmartPhone is CamStarter, which is "the" user interface for the camera system. The CamStarter user interface allows a user to start/stop the camera application and transfer files to the server. The CamStarter application interfaces to the CamTest application through registry settings. Both the CamStarter and CamTest applications must be separately deployed on themore » smartphone to run the camera system application. When a user selects the Start button in CamStarter, CamTest is created as a process. The smartphone begins taking small pictures (CAPTURE mode), analyzing those pictures for certain conditions, and saving those pictures on the smartphone. This process will terminate when the user selects the Stop button. The camtest code spins off an asynchronous thread, StreamIOHandler, to check for pictures taken by the camera. The received image is then tested by StreamIOHandler to see if it meets certain conditions. If those conditions are met, the CamTest program is notified through the setting of a registry key value and the image is saved in a designated directory in a custom BMP file which includes a header and the image data. When the user selects the Transfer button in the CamStarter user interface, the covertsmartdevice code is created as a process. Covertsmartdevice gets all of the files in a designated directory, opens a socket connection to the server, sends each file, and then terminates.« less

Analysis of the release process of phenylpropanolamine hydrochloride from ethylcellulose matrix granules III. Effects of the dissolution condition on the release process.

PubMed

Fukui, Atsuko; Fujii, Ryuta; Yonezawa, Yorinobu; Sunada, Hisakazu

2006-08-01

In the pharmaceutical preparation of a controlled release drug, it is very important and necessary to understand the entire release properties. As the first step, the dissolution test under various conditions is selected for the in vitro test, and usually the results are analyzed following Drug Approval and Licensing Procedures. In this test, 3 time points for each release ratio, such as 0.2-0.4, 0.4-0.6, and over 0.7, respectively, should be selected in advance. These are analyzed as to whether their values are inside or outside the prescribed aims at each time point. This method is very simple and useful but the details of the release properties can not be clarified or confirmed. The validity of the dissolution test in analysis using a combination of the square-root time law and cube-root law equations to understand all the drug release properties was confirmed by comparing the simulated value with that measured in the previous papers. Dissolution tests under various conditions affecting drug release properties in the human body were then examined, and the results were analyzed by both methods to identify their strengths and weaknesses. Hereafter, the control of pharmaceutical preparation, the manufacturing process, and understanding the drug release properties will be more efficient. It is considered that analysis using the combination of the square-root time law and cube-root law equations is very useful and efficient. The accuracy of predicting drug release properties in the human body was improved and clarified.

Investigation of organic matter migrating from polymeric pipes into drinking water under different flow manners.

PubMed

Zhang, Ling; Liu, Shuming; Liu, Wenjun

2014-02-01

Polymeric pipes, such as unplasticized polyvinyl chloride (uPVC) pipes, polypropylene random (PPR) pipes and polyethylene (PE) pipes are increasingly used for drinking water distribution lines. Plastic pipes may include some additives like metallic stabilizers and other antioxidants for the protection of the material during its production and use. Thus, some compounds can be released from those plastic pipes and cast a shadow on drinking water quality. This work develops a new procedure to investigate three types of polymer pipes (uPVC, PE and PPR) with respect to the migration of total organic carbon (TOC) into drinking water. The migration test was carried out in stagnant conditions with two types of migration processes, a continuous migration process and a successive migration process. These two types of migration processes are specially designed to mimic the conditions of different flow manners in drinking water pipelines, i.e., the situation of continuous stagnation with long hydraulic retention times and normal flow status with regular water renewing in drinking water networks. The experimental results showed that TOC release differed significantly with different plastic materials and under different flow manners. The order of materials with respect to the total amount of TOC migrating into drinking water was observed as PE > PPR > uPVC under both successive and continuous migration conditions. A higher amount of organic migration from PE and PPR pipes was likely to occur due to more organic antioxidants being used in pipe production. The results from the successive migration tests indicated the trend of the migration intensity of different pipe materials over time, while the results obtained from the continuous migration tests implied that under long stagnant conditions, the drinking water quality could deteriorate quickly with the consistent migration of organic compounds and the dramatic consumption of chlorine to a very low level. Higher amounts of TOC were released under the continuous migration tests.

Temperature dependency in motor skill learning.

PubMed

Immink, Maarten A; Wright, David L; Barnes, William S

2012-01-01

The present study investigated the role of temperature as a contextual condition for motor skill learning. Precision grip task training occurred while forearm cutaneous temperature was either heated (40-45 °C) or cooled (10-15 °C). At test, temperature was either reinstated or changed. Performance was comparable between training conditions while at test, temperature changes decreased accuracy, especially after hot training conditions. After cold training, temperature change deficits were only evident when concurrent force feedback was presented. These findings are the first evidence of localized temperature dependency in motor skill learning in humans. Results are not entirely accounted for by a context-dependent memory explanation and appear to represent an interaction of neuromuscular and sensory processes with the temperature present during training and test.

Reliability analysis of nutrient removal from stormwater runoff with green sorption media under varying influent conditions.

PubMed

Jones, Jamie; Chang, Ni-Bin; Wanielista, Martin P

2015-01-01

To support nutrient removal, various stormwater treatment technologies have been developed via the use of green materials, such as sawdust, tire crumbs, sand, clay, sulfur, and limestone, as typical constituents of filter media mixes. These materials aid in the physiochemical sorption and precipitation of orthophosphates as well as in the biological transformation of ammonia, nitrates and nitrites. However, these processes are dependent upon influent conditions such as hydraulic residence time, influent orthophosphate concentrations, and other chemical species present in the inflow. This study aims to compare the physiochemical removal of orthophosphate by isotherm and column tests under differing influent conditions to realize the reliability of orthophosphate removal process with the aid of green sorption media. The green sorption media of interest in this study is composed of a 5:2:2:1 (by volume) mixture of cement sand, tire crumb, fine expanded clay, and limestone. Scenarios of manipulating the hydraulic residence time of the water from 18 min and 60 min, the influent dissolved phosphorus concentrations of 1.0 mg·L(-1) and 0.5 mg·L(-1), and influent water types of distilled and pond water, were all investigated in the column tests. Experimental data were compared with the outputs from the Thomas Model based on orthophosphate removal to shed light on the equilibrium condition versus kinetic situation. With ANOVA tests, significant differences were confirmed between the experimental data sets of the breakthrough curves in the column tests. SEM imaging analysis helps to deepen the understanding of pore structures and pore networks of meta-materials being used in the green sorption media. Life expectancy curves derived from the output of Thomas Model may be applicable for future system design of engineering processes. Copyright © 2014 Elsevier B.V. All rights reserved.

SiC Composite for Fuel Structure Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yueh, Ken

Extensive evaluation was performed to determine the suitability of using SiC composite as a boiling water reactor (BWR) fuel channel material. A thin walled SiC composite box, 10 cm in dimension by approximately 1.5 mm wall thickness was fabricated using chemical vapor deposition (CVD) for testing. Mechanical test results and performance evaluations indicate the material could meet BWR channel mechanical design requirement. However, large mass loss of up to 21% was measured in in-pile corrosion test under BWR-like conditions in under 3 months of irradiation. A fresh sister sample irradiated in a follow-up cycle under PWR conditions showed no measureablemore » weight loss and thus supports the hypothesis that the oxidizing condition of the BWR-like coolant chemistry was responsible for the high corrosion rate. A thermodynamic evaluation showed SiC is not stable and the material may oxidize to form SiO 2 and CO 2. Silica has demonstrated stability in high temperature steam environment and form a protective oxide layer under severe accident conditions. However, it does not form a protective layer in water under normal BWR operational conditions due to its high solubility. Corrosion product stabilization by modifying the SiC CVD surface is an approach evaluated in this study to mitigate the high corrosion rate. Titanium and zirconium have been selected as stabilizing elements since both TiSiO 4 and ZrSiO 4 are insoluble in water. Corrosion test results in oxygenated water autoclave indicate TiSiO4 does not form a protective layer. However, zirconium doped test samples appear to form a stable continuous layer of ZrSiO 4 during the corrosion process. Additional process development is needed to produce a good ZrSiC coating to verify functionality of the mitigation concept.« less

40 CFR 766.32 - Exclusions and waivers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ACT DIBENZO-PARA-DIOXINS/DIBENZOFURANS Specific Chemical Testing/Reporting Requirements § 766.32...: (1) Exclusions may be granted if. (i) Testing of the appropriate grade of the chemical substance has... a well-designed bioassay with appropriate QA/QC or; (ii) Process and reaction conditions of the...

ETV REPORT AND VERIFICATION STATEMENT; EVALUATION OF LOBO LIQUIDS RINSE WATER RECOVERY SYSTEM

EPA Science Inventory

The Lobo Liquids Rinse Water Recovery System (Lobo Liquids system) was tested, under actual production conditions, processing metal finishing wastewater, at Gull Industries in Houston, Texas. The verification test evaluated the ability of the ion exchange (IX) treatment system t...

Stress-corrosion behavior of aluminum-lithium alloys in aqueous salt environments

NASA Technical Reports Server (NTRS)

Pizzo, P. P.; Galvin, R. P.; Nelson, H. G.

1984-01-01

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg; two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Stress-corrosion behavior of aluminum-lithium alloys in aqueous environments

NASA Technical Reports Server (NTRS)

Pizzo, P. P.; Galvin, R. P.; Nelson, H. G.

1983-01-01

The stress corrosion susceptibility of two powder metallurgy (P/M) alloys, Al-Li-Cu and Al-Li-Cu-Mg two mechanically attrited (M/A) alloys, Al-Li-Cu and Al-Li-Mg; and two wrought, ingot alloys, X-2020 and AA7475, are compared. Time-dependent fracture in an aqueous sodium chloride environment under alternate immersion condition was found to vary significantly between alloys. The stress corrosion behavior of the two powder metallurgy processed alloys was studied in detail under conditions of crack initiation, static crack growth, and fatigue crack growth. A variety of stress corrosion tests were performed including smooth surface, time-to-failure tests; potentiostatic tests on smooth surfaces exposed to constant applied strain rates; and fracture mechanics-type tests under static and cyclic loads. Both alloys show surface pitting and subsequent intergranular corrosion. Pitting is more severe in the magnesium-bearing alloy and is associated with stringer particles strung along the extrusion direction as a result of P/M processing.

Ethical dilemmas in genetic testing: examples from the Cuban program for predictive diagnosis of hereditary ataxias.

PubMed

Mariño, Tania Cruz; Armiñán, Rubén Reynaldo; Cedeño, Humberto Jorge; Mesa, José Miguel Laffita; Zaldivar, Yanetza González; Rodríguez, Raúl Aguilera; Santos, Miguel Velázquez; Mederos, Luis Enrique Almaguer; Herrera, Milena Paneque; Pérez, Luis Velázquez

2011-06-01

Predictive testing protocols are intended to help patients affected with hereditary conditions understand their condition and make informed reproductive choices. However, predictive protocols may expose clinicians and patients to ethical dilemmas that interfere with genetic counseling and the decision making process. This paper describes ethical dilemmas in a series of five cases involving predictive testing for hereditary ataxias in Cuba. The examples herein present evidence of the deeply controversial situations faced by both individuals at risk and professionals in charge of these predictive studies, suggesting a need for expanded guidelines to address such complexities.

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2012 CFR

2012-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2014 CFR

2014-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

40 CFR 63.11945 - What performance testing requirements must I meet for process vents?

Code of Federal Regulations, 2013 CFR

2013-07-01

... conduct the initial and periodic performance tests required in § 63.11925(d) and (e) and as specified in... tests under the conditions specified in paragraphs (b)(1) through (3) of this section, as applicable. Upon request, the owner or operator shall make available to the Administrator such records as may be...

Soil conservation service tests of Eucalyptus species for windbreaks

Treesearch

Gary L. Young

1983-01-01

The Soil Conservation Service is in the early stages of testing many species of Eucalyptus or windbreaks. Over 260 different species have been collected. The pre-planting selection criteria and process is described as well as the test conditions and procedures. Some sources of information on the use of the Eucalypts may be misleading through...

Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

EPA Pesticide Factsheets

The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

Categorical Speech Perception in Adults with Autism Spectrum Conditions

ERIC Educational Resources Information Center

Stewart, Mary E.; Petrou, Alexandra M.; Ota, Mitsuhiko

2018-01-01

This study tested whether individuals with autism spectrum conditions (n = 23) show enhanced discrimination of acoustic differences that signal a linguistic contrast (i.e., /g/ versus /k/ as in "goat" and "coat") and whether they process such differences in a less categorical fashion as compared with 23 IQ-matched typically…

Misremembering what you see or hear: Dissociable effects of modality on short- and long-term false recognition.

PubMed

Olszewska, Justyna M; Reuter-Lorenz, Patricia A; Munier, Emily; Bendler, Sara A

2015-09-01

False working memories readily emerge using a visual item-recognition variant of the converging associates task. Two experiments, manipulating study and test modality, extended prior working memory results by demonstrating a reliable false recognition effect (more false alarms to associatively related lures than to unrelated lures) within seconds of encoding in either the visual or auditory modality. However, false memories were nearly twice as frequent when study lists were seen than when they were heard, regardless of test modality, although study-test modality mismatch was generally disadvantageous (consistent with encoding specificity). A final experiment that varied study-test modality using a hybrid short- and long-term memory test (Flegal, Atkins & Reuter-Lorenz, 2010) replicated the auditory advantage in the short term but revealed a reversal in the long term: The false memory effect was greater in the auditory study-test condition than in the visual study-test condition. Thus, the same encoding conditions gave rise to an opposite modality advantage depending on whether recognition was tested under short-term or long-term memory conditions. Although demonstrating continuity in associative processing across delay, the results indicate that delay condition affects the availability of modality-dependent features of the memory trace and, thus, distinctiveness, leading to dissociable patterns of short- and long-term memory performance. (c) 2015 APA, all rights reserved).

The Relationships Between Microstructure, Tensile Properties and Fatigue Life in Ti-5Al-5V-5Mo-3Cr-0.4Fe (Ti-5553)

NASA Astrophysics Data System (ADS)

Foltz, John W., IV

beta-titanium alloys are being increasingly used in airframes as a way to decrease the weight of the aircraft. As a result of this movement, Ti-5Al-5V-5Mo-3Cr-0.4Fe (Timetal 555), a high-strength beta titanium alloy, is being used on the current generation of landing gear. This alloy features good combinations of strength, ductility, toughness and fatigue life in alpha+beta processed conditions, but little is known about beta-processed conditions. Recent work by the Center for the Accelerated Maturation of Materials (CAMM) research group at The Ohio State University has improved the tensile property knowledge base for beta-processed conditions in this alloy, and this thesis augments the aforementioned development with description of how microstructure affects fatigue life. In this work, beta-processed microstructures have been produced in a Gleeble(TM) thermomechanical simulator and subsequently characterized with a combination of electron and optical microscopy techniques. Four-point bending fatigue tests have been carried out on the material to characterize fatigue life. All the microstructural conditions have been fatigue tested with the maximum test stress equal to 90% of the measured yield strength. The subsequent results from tensile tests, fatigue tests, and microstructural quantification have been analyzed using Bayesian neural networks in an attempt to predict fatigue life using microstructural and tensile inputs. Good correlation has been developed between lifetime predictions and experimental results using microstructure and tensile inputs. Trained Bayesian neural networks have also been used in a predictive fashion to explore functional dependencies between these inputs and fatigue life. In this work, one section discusses the thermal treatments that led to the observed microstructures, and the possible sequence of precipitation that led to these microstructures. The thesis then describes the implications of microstructure on fatigue life and implications of tensile properties on fatigue life. Several additional experiments are then described that highlight possible causes for the observed dependence of microstructure on fatigue life, including fractographic evidence to provide support of microstructural dependencies.

Distinct Effects of Lexical and Semantic Competition during Picture Naming in Younger Adults, Older Adults, and People with Aphasia

PubMed Central

Britt, Allison E.; Ferrara, Casey; Mirman, Daniel

2016-01-01

Producing a word requires selecting among a set of similar alternatives. When many semantically related items become activated, the difficulty of the selection process is increased. Experiment 1 tested naming of items with either multiple synonymous labels (“Alternate Names,” e.g., gift/present) or closely semantically related but non-equivalent responses (“Near Semantic Neighbors,” e.g., jam/jelly). Picture naming was fastest and most accurate for pictures with only one label (“High Name Agreement”), slower and less accurate in the Alternate Names condition, and slowest and least accurate in the Near Semantic Neighbors condition. These results suggest that selection mechanisms in picture naming operate at two distinct levels of processing: selecting between similar but non-equivalent names requires two selection processes (semantic and lexical), whereas selecting among equivalent names only requires one selection at the lexical level. Experiment 2 examined how these selection mechanisms are affected by normal aging and found that older adults had significantly more difficulty in the Near Semantic Neighbors condition, but not in the Alternate Names condition. This suggests that aging affects semantic processing and selection more strongly than it affects lexical selection. Experiment 3 examined the role of the left inferior frontal gyrus (LIFG) in these selection processes by testing individuals with aphasia secondary to stroke lesions that either affected the LIFG or spared it. Surprisingly, there was no interaction between condition and lesion group: the presence of LIFG damage was not associated with substantively worse naming performance for pictures with multiple acceptable labels. These results are not consistent with a simple view of LIFG as the locus of lexical selection and suggest a more nuanced view of the neural basis of lexical and semantic selection. PMID:27458393

Design of scaled down structural models

NASA Technical Reports Server (NTRS)

Simitses, George J.

1994-01-01

In the aircraft industry, full scale and large component testing is a very necessary, time consuming, and expensive process. It is essential to find ways by which this process can be minimized without loss of reliability. One possible alternative is the use of scaled down models in testing and use of the model test results in order to predict the behavior of the larger system, referred to herein as prototype. This viewgraph presentation provides justifications and motivation for the research study, and it describes the necessary conditions (similarity conditions) for two structural systems to be structurally similar with similar behavioral response. Similarity conditions provide the relationship between a scaled down model and its prototype. Thus, scaled down models can be used to predict the behavior of the prototype by extrapolating their experimental data. Since satisfying all similarity conditions simultaneously is in most cases impractical, distorted models with partial similarity can be employed. Establishment of similarity conditions, based on the direct use of the governing equations, is discussed and their use in the design of models is presented. Examples include the use of models for the analysis of cylindrical bending of orthotropic laminated beam plates, of buckling of symmetric laminated rectangular plates subjected to uniform uniaxial compression and shear, applied individually, and of vibrational response of the same rectangular plates. Extensions and future tasks are also described.

Design of scaled down structural models

NASA Astrophysics Data System (ADS)

Simitses, George J.

1994-07-01

In the aircraft industry, full scale and large component testing is a very necessary, time consuming, and expensive process. It is essential to find ways by which this process can be minimized without loss of reliability. One possible alternative is the use of scaled down models in testing and use of the model test results in order to predict the behavior of the larger system, referred to herein as prototype. This viewgraph presentation provides justifications and motivation for the research study, and it describes the necessary conditions (similarity conditions) for two structural systems to be structurally similar with similar behavioral response. Similarity conditions provide the relationship between a scaled down model and its prototype. Thus, scaled down models can be used to predict the behavior of the prototype by extrapolating their experimental data. Since satisfying all similarity conditions simultaneously is in most cases impractical, distorted models with partial similarity can be employed. Establishment of similarity conditions, based on the direct use of the governing equations, is discussed and their use in the design of models is presented. Examples include the use of models for the analysis of cylindrical bending of orthotropic laminated beam plates, of buckling of symmetric laminated rectangular plates subjected to uniform uniaxial compression and shear, applied individually, and of vibrational response of the same rectangular plates. Extensions and future tasks are also described.

Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

DOE PAGES

Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene; ...

2016-02-06

Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene

Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

Generalized ISAR--part I: an optimal method for imaging large naval vessels.

PubMed

Given, James A; Schmidt, William R

2005-11-01

We describe a generalized inverse synthetic aperture radar (ISAR) process that performs well under a wide variety of conditions common to the naval ISAR tests of large vessels. In particular, the generalized ISAR process performs well in the presence of moderate intensity ship roll. The process maps localized scatterers onto peaks on the ISAR plot. However, in a generalized ISAR plot, each of the two coordinates of a peak is a fixed linear combination of the three ship coordinates of the scatterer causing the peak. Combining this process with interferometry will then provide high-accuracy three-dimensional location of the important scatterers on a ship. We show that ISAR can be performed in the presence of simultaneous roll and aspect change, provided the two Doppler rates are not too close in magnitude. We derive the equations needed for generalized ISAR, both roll driven and aspect driven, and test them against simulations performed in a variety of conditions, including large roll amplitudes.

Automaticity in reading and the Stroop task: testing the limits of involuntary word processing.

PubMed

Brown, Tracy L; Joneleit, Kelly; Robinson, Cathy S; Brown, Carli Rose

2002-01-01

We investigated the parameters of involuntary word reading in the Stroop task in 7 experiments. Experiments 1-4 varied response modality and the presence of congruent word trials in a test of the claim that presenting a Stroop color word with only one letter in the target color eliminates the Stroop effect. Experiments 5 and 6 addressed the roles of spatial attention and orthographic processing as possible mechanisms behind the reduction of Stroop effects with the single-letter format. Experiment 7 investigated the limits of involuntary reading under optimal conditions for selective processing of rectangular color patch targets. We found that the single-letter format reduced but never eliminated Stroop effects, spatial attention but not orthographic processing plays a role in the effect of the single-letter format, and word reading is not completely prevented even with austere presentation conditions. We conclude with a defense of the involuntariness criterion for automaticity in the Stroop task, particularly when word reading is viewed in the context of a skilled performance.

Developing a modified preservative efficacy testing approach as a predictive tool for the evaluation of preservative systems in liquid home care products under variable test conditions.

PubMed

Hoyt, Anne L; Bushman, Don; Lewis, Nathan; Faber, Robert

2012-01-01

How can a formulator have confidence that a preservative system will perform as expected under adverse conditions? Extreme conditions that can lead to the development of "off odors" in the product can be a serious challenge for companies providing home care products in the global market. Formulation and stability testing occur under controlled parameters that simulate limited environmental conditions and microbial challenges are typically performed with a standard inoculum level. While this is an acceptable and dependable process, it does not necessarily assess how well a preservative system can perform under extreme environmental conditions or against unusually high levels of bacterial challenges. This is especially true when formulations are diluted and stored by the end-user. By modifying microbial challenge testing of a liquid dishwashing product to include unexpected dilution schemes, increased microbial assaults, and elevated temperatures, a pattern of preservative efficacy was established. The resulting approach proved to be a useful tool when developing use directions, recommended dilution levels, the overall surfactant system, preservative type, and storage restrictions.

Evaluation of Candidate Millimeter Wave Sensors for Synthetic Vision

NASA Technical Reports Server (NTRS)

Alexander, Neal T.; Hudson, Brian H.; Echard, Jim D.

1994-01-01

The goal of the Synthetic Vision Technology Demonstration Program was to demonstrate and document the capabilities of current technologies to achieve safe aircraft landing, take off, and ground operation in very low visibility conditions. Two of the major thrusts of the program were (1) sensor evaluation in measured weather conditions on a tower overlooking an unused airfield and (2) flight testing of sensor and pilot performance via a prototype system. The presentation first briefly addresses the overall technology thrusts and goals of the program and provides a summary of MMW sensor tower-test and flight-test data collection efforts. Data analysis and calibration procedures for both the tower tests and flight tests are presented. The remainder of the presentation addresses the MMW sensor flight-test evaluation results, including the processing approach for determination of various performance metrics (e.g., contrast, sharpness, and variability). The variation of the very important contrast metric in adverse weather conditions is described. Design trade-off considerations for Synthetic Vision MMW sensors are presented.

Recent Improvements in Semi-Span Testing at the National Transonic Facility (Invited)

NASA Technical Reports Server (NTRS)

Gatlin, G. M.; Tomek, W. G.; Payne, F. M.; Griffiths, R. C.

2006-01-01

Three wind tunnel investigations of a commercial transport, high-lift, semi-span configuration have recently been conducted in the National Transonic Facility at the NASA Langley Research Center. Throughout the course of these investigations multiple improvements have been developed in the facility semi-span test capability. The primary purpose of the investigations was to assess Reynolds number scale effects on a modern commercial transport configuration up to full-scale flight test conditions (Reynolds numbers on the order of 27 million). The tests included longitudinal aerodynamic studies at subsonic takeoff and landing conditions across a range of Reynolds numbers from that available in conventional wind tunnels up to flight conditions. The purpose of this paper is to discuss lessons learned and improvements incorporated into the semi-span testing process. Topics addressed include enhanced thermal stabilization and moisture reduction procedures, assessments and improvements in model sealing techniques, compensation of model reference dimensions due to test temperature, significantly improved semi-span model access capability, and assessments of data repeatability.

Newborn screening of metabolic disorders: recent progress and future developments.

PubMed

Rinaldo, Piero; Lim, James S; Tortorelli, Silvia; Gavrilov, Dimitar; Matern, Dietrich

2008-01-01

Tandem mass spectrometry has been the main driver behind a significant expansion in newborn screening programs. The ability to detect more than 40 conditions by a single test underscores the need to better understand the clinical and laboratory characteristics of the conditions being tested, and the complexity of pattern recognition and differential diagnoses of one or more elevated markers. The panel of conditions recommended by the American College of Medical Genetics, including 20 primary conditions and 22 secondary targets that are detectable by tandem mass spectrometry has been adopted as the standard of care in the vast majority of US states. The evolution of newborn screening is far from being idle as a large number of infectious, genetic, and metabolic conditions are currently under investigation at variable stages of test development and clinical validation. In the US, a formal process with oversight by the Advisory Committee on Heritable Disorders and Genetic Diseases in Newborns and Children has been established for nomination and evidence-based review of new candidate conditions. If approved, these conditions could be added to the uniform panel and consequently pave the way to large scale implementation.

The algorithm for automatic detection of the calibration object

NASA Astrophysics Data System (ADS)

Artem, Kruglov; Irina, Ugfeld

2017-06-01

The problem of the automatic image calibration is considered in this paper. The most challenging task of the automatic calibration is a proper detection of the calibration object. The solving of this problem required the appliance of the methods and algorithms of the digital image processing, such as morphology, filtering, edge detection, shape approximation. The step-by-step process of the development of the algorithm and its adopting to the specific conditions of the log cuts in the image's background is presented. Testing of the automatic calibration module was carrying out under the conditions of the production process of the logging enterprise. Through the tests the average possibility of the automatic isolating of the calibration object is 86.1% in the absence of the type 1 errors. The algorithm was implemented in the automatic calibration module within the mobile software for the log deck volume measurement.

(Re)evaluating the Implications of the Autoregressive Latent Trajectory Model Through Likelihood Ratio Tests of Its Initial Conditions.

PubMed

Ou, Lu; Chow, Sy-Miin; Ji, Linying; Molenaar, Peter C M

2017-01-01

The autoregressive latent trajectory (ALT) model synthesizes the autoregressive model and the latent growth curve model. The ALT model is flexible enough to produce a variety of discrepant model-implied change trajectories. While some researchers consider this a virtue, others have cautioned that this may confound interpretations of the model's parameters. In this article, we show that some-but not all-of these interpretational difficulties may be clarified mathematically and tested explicitly via likelihood ratio tests (LRTs) imposed on the initial conditions of the model. We show analytically the nested relations among three variants of the ALT model and the constraints needed to establish equivalences. A Monte Carlo simulation study indicated that LRTs, particularly when used in combination with information criterion measures, can allow researchers to test targeted hypotheses about the functional forms of the change process under study. We further demonstrate when and how such tests may justifiably be used to facilitate our understanding of the underlying process of change using a subsample (N = 3,995) of longitudinal family income data from the National Longitudinal Survey of Youth.

Antennal tactile learning in the honeybee: effect of nicotinic antagonists on memory dynamics.

PubMed

Dacher, M; Lagarrigue, A; Gauthier, M

2005-01-01

Restrained worker honeybees (Apis mellifera L.) are able to learn to associate antennal-scanning of a metal plate with a sucrose reinforcement delivered to the mouthparts. Learning occurs reliably in a single association of the two sensory stimuli. The involvement of nicotinic pathways in memory formation and retrieval processes was tested by injecting, into the whole brain through the median ocellus, either mecamylamine (0.6 microg per bee) or alpha-bungarotoxin (2.4 ng per bee). Saline served as a control. Mecamylamine injected 10 min before the retrieval test impairs the retention level tested 3 h and 24 h after single- or multi-trial learning. Retrieval tests performed at various times after the injection show that the blocking effect of mecamylamine lasts about 1 h. The drug has no effect on the reconsolidation or extinction processes. Mecamylamine injected 10 min before conditioning impairs single-trial learning but has no effect on five-trial learning and on the consolidation process. By contrast, alpha-bungarotoxin only impairs the formation of long-term memory (24 h) induced by the five-trial learning and has no effect on medium-term memory (3 h), on single-trial learning or on the retrieval process. Hence, owing to previous data, at least two kinds of nicotinic receptors seem to be involved in honeybee memory, an alpha-bungarotoxin-sensitive and an alpha-bungarotoxin-insensitive receptor. Our results extend to antennal mechanosensory conditioning the role of the cholinergic system that we had previously described for olfactory conditioning in the honeybee. Moreover, we describe here in this insect a pharmacological dissociation between alpha-bungarotoxin sensitive long-term memory and alpha-bungarotoxin insensitive medium-term memory, the last one being affected by mecamylamine.

Instrumentation & Data Acquisition System (D AS) Engineer

NASA Technical Reports Server (NTRS)

Jackson, Markus Deon

2015-01-01

The primary job of an Instrumentation and Data Acquisition System (DAS) Engineer is to properly measure physical phenomenon of hardware using appropriate instrumentation and DAS equipment designed to record data during a specified test of the hardware. A DAS system includes a CPU or processor, a data storage device such as a hard drive, a data communication bus such as Universal Serial Bus, software to control the DAS system processes like calibrations, recording of data and processing of data. It also includes signal conditioning amplifiers, and certain sensors for specified measurements. My internship responsibilities have included testing and adjusting Pacific Instruments Model 9355 signal conditioning amplifiers, writing and performing checkout procedures, writing and performing calibration procedures while learning the basics of instrumentation.

Real time automatic detection of bearing fault in induction machine using kurtogram analysis.

PubMed

Tafinine, Farid; Mokrani, Karim

2012-11-01

A proposed signal processing technique for incipient real time bearing fault detection based on kurtogram analysis is presented in this paper. The kurtogram is a fourth-order spectral analysis tool introduced for detecting and characterizing non-stationarities in a signal. This technique starts from investigating the resonance signatures over selected frequency bands to extract the representative features. The traditional spectral analysis is not appropriate for non-stationary vibration signal and for real time diagnosis. The performance of the proposed technique is examined by a series of experimental tests corresponding to different bearing conditions. Test results show that this signal processing technique is an effective bearing fault automatic detection method and gives a good basis for an integrated induction machine condition monitor.

Characterization of the Tribological Behavior of Oxide-Based NanoMaterials: Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fenske, George

2017-01-04

Under the Argonne/Pixelligent cooperative research and development agreement (CRADA – C1200801), Argonne performed labscale tribological tests on proprietary nano-sized ZrO 2 material developed by Pixelligent. Pixelligent utilized their proprietary process to prepare variants with different surfactants at different loadings in different carrier fluids for testing and evaluation at Argonne. Argonne applied a range of benchtop tribological test rigs to evaluate friction and wear under a range of conditions (contact geometry, loads, speeds, and temperature) that simulated a broad range of conditions experienced in engines and driveline components. Post-test analysis of worn surfaces provided information on the structure and chemistry ofmore » the tribofilms produced during the tests.« less

Development of vapor phase hydrogen peroxide sterilization process for spacecraft applications

NASA Technical Reports Server (NTRS)

Rohatgi, N.; Schubert, W.; Knight, J.; Quigley, M.; Forsberg, G.; Ganapathi, G.; Yarbrough, C.; Koukol, R.

2001-01-01

This paper will present test data and discussion on the work we are conducting at JPL to address the following issues: 1) efficacy of sterilization process; 2) diffusion of hydrogen peroxide under sterilization process conditions into hard to reach places; 3) materials and components compatibility with the sterilization process and 4) development of methodology to protect sensitive components from hydrogen peroxide vapor.

Configural and component processing in simultaneous and sequential lineup procedures.

PubMed

Flowe, Heather D; Smith, Harriet M J; Karoğlu, Nilda; Onwuegbusi, Tochukwu O; Rai, Lovedeep

2016-01-01

Configural processing supports accurate face recognition, yet it has never been examined within the context of criminal identification lineups. We tested, using the inversion paradigm, the role of configural processing in lineups. Recent research has found that face discrimination accuracy in lineups is better in a simultaneous compared to a sequential lineup procedure. Therefore, we compared configural processing in simultaneous and sequential lineups to examine whether there are differences. We had participants view a crime video, and then they attempted to identify the perpetrator from a simultaneous or sequential lineup. The test faces were presented either upright or inverted, as previous research has shown that inverting test faces disrupts configural processing. The size of the inversion effect for faces was the same across lineup procedures, indicating that configural processing underlies face recognition in both procedures. Discrimination accuracy was comparable across lineup procedures in both the upright and inversion condition. Theoretical implications of the results are discussed.

Evaluation of Fracture Initiation in the Mannesmann Piercing Process

NASA Astrophysics Data System (ADS)

Fanini, S.; Ghiotti, A.; Bruschi, S.

2007-04-01

One of the challenging objectives in studying the Mannesmann piercing process is to predict the fracture initiation, known as "Mannesmann effect", in order to design and optimize the working parameters of the piercing process. The objective of the paper is to investigate the workability of a tube steel tested in the same conditions of the Mannesman piercing process. The stress and strain states as well as temperature fields arising during the process are identified through numerical simulations. The hot tensile test is chosen for fundamental studies on fracture initiation, as a tensile state of stress in the centre of the billet in the first stages of the piercing process before the plug arrival seems to be one of the main causes of the crack initiation. The material constants of energy-based models implemented in FEM codes are calculated and numerical results are compared with non-plug piercing tests carried out on the industrial plant.

The dynamic nature of the reconsolidation process and its boundary conditions: Evidence based on human tests.

PubMed

Fernández, Rodrigo S; Bavassi, Luz; Forcato, Cecilia; Pedreira, María E

2016-04-01

The reconsolidation process is the mechanism by which the strength and/or content of consolidated memories are updated. This process is triggered by the presentation of a reminder (training cues). It is not always possible to trigger the reconsolidation process. For example, memory age and strength are boundary conditions for the reconsolidation process. Here, we investigated the dynamic changes in these conditions. We propose that the boundary conditions of the reconsolidation process are not fixed and vary as a consequence of the interaction between memory features and reminder characteristics. To modify memory properties, participants received a threatening social protocol that improves memory acquisition or a control condition (fake, without social interaction) prior to learning pairs of meaningless syllables. To determine whether a strong young or old declarative memory undergoes the reconsolidation process, we used an interference task (a second list of pairs of meaningless syllables) to disrupt memory re-stabilization. To assess whether the older memory could be strengthened, we repeated the triggering of reconsolidation. Strong young or old memories modulated by a threatening experience could be interfered during reconsolidation and updated (strengthened) by reconsolidation. Rather than being fixed, boundary conditions vary according to the memory features (strong memory), which indicates the dynamic nature of the reconsolidation process. Our findings demonstrate that it is possible to modify these limits by recruiting the reconsolidation process and making it functionally operative again. This novel scenario opens the possibility to new therapeutically approaches that take into account the reconsolidation process. Copyright © 2016 Elsevier Inc. All rights reserved.

Mood as a resource in dealing with health recommendations: how mood affects information processing and acceptance of quit-smoking messages.

PubMed

Das, Enny; Vonkeman, Charlotte; Hartmann, Tilo

2012-01-01

An experimental study tested the effects of positive and negative mood on the processing and acceptance of health recommendations about smoking in an online experiment. It was hypothesised that positive mood would provide smokers with the resources to systematically process self-relevant health recommendations. One hundred and twenty-seven participants (smokers and non-smokers) read a message in which a quit smoking programme was recommended. Participants were randomly assigned to one of four conditions: positive versus negative mood, and strong versus weak arguments for the recommended action. Systematic message processing was inferred when participants were able to distinguish between high- and low-quality arguments, and by congruence between attitudes and behavioural intentions. Persuasion was measured by participant's attitudes towards smoking and the recommended action, and by their intentions to follow the action recommendation. As predicted, smokers systematically processed the health message only under positive mood conditions; non-smokers systematically processed the health message only under negative mood conditions. Moreover, smokers' attitudes towards the health message predicted intentions to quit smoking only under positive mood conditions. Findings suggest that positive mood may decrease defensive processing of self-relevant health information.

Impact of Educational Level on Performance on Auditory Processing Tests.

PubMed

Murphy, Cristina F B; Rabelo, Camila M; Silagi, Marcela L; Mansur, Letícia L; Schochat, Eliane

2016-01-01

Research has demonstrated that a higher level of education is associated with better performance on cognitive tests among middle-aged and elderly people. However, the effects of education on auditory processing skills have not yet been evaluated. Previous demonstrations of sensory-cognitive interactions in the aging process indicate the potential importance of this topic. Therefore, the primary purpose of this study was to investigate the performance of middle-aged and elderly people with different levels of formal education on auditory processing tests. A total of 177 adults with no evidence of cognitive, psychological or neurological conditions took part in the research. The participants completed a series of auditory assessments, including dichotic digit, frequency pattern and speech-in-noise tests. A working memory test was also performed to investigate the extent to which auditory processing and cognitive performance were associated. The results demonstrated positive but weak correlations between years of schooling and performance on all of the tests applied. The factor "years of schooling" was also one of the best predictors of frequency pattern and speech-in-noise test performance. Additionally, performance on the working memory, frequency pattern and dichotic digit tests was also correlated, suggesting that the influence of educational level on auditory processing performance might be associated with the cognitive demand of the auditory processing tests rather than auditory sensory aspects itself. Longitudinal research is required to investigate the causal relationship between educational level and auditory processing skills.

The Replicability of the Negative Testing Effect: Differences across Participant Populations

ERIC Educational Resources Information Center

Mulligan, Neil W.; Rawson, Katherine A.; Peterson, Daniel J.; Wissman, Kathryn T.

2018-01-01

Although memory retrieval often enhances subsequent memory, Peterson and Mulligan (2013) reported conditions under which retrieval produces poorer subsequent recall--the negative testing effect. The item-specific--relational account proposes that the effect occurs when retrieval disrupts interitem organizational processing relative to the restudy…

The European DISABKIDS project: development of seven condition-specific modules to measure health related quality of life in children and adolescents

PubMed Central

Baars, Rolanda M; Atherton, Clare I; Koopman, Hendrik M; Bullinger, Monika; Power, Mick

2005-01-01

Background The European DISABKIDS project aims to enhance the Health Related Quality of Life (HRQoL) of children and adolescents with chronic medical conditions and their families. We describe the development of the seven cross-nationally tested condition-specific modules of the European DISABKIDS HRQoL instrument in a population of children and adolescents. The condition-specific modules are intended for use in conjunction with the DISABKIDS chronic generic module. Methods Focus groups were used to construct the pilot version of the DISABKIDS condition-specific HRQoL modules for asthma, juvenile idiopathic arthritis, atopic dermatitis, cerebral palsy, cystic fibrosis, diabetes and epilepsy. Analyses were conducted on pilot test data in order to construct field test versions of the modules. A series of factor analyses were run, first, to determine potential structures for each condition-specific module, and, secondly, to select a reduced number of items from the pilot test to be included in the field test. Post-field test analyses were conducted to retest the domain structure for the final DISABKIDS condition-specific modules. Results The DISABKIDS condition-specific modules were tested in a pilot study of 360 respondents, and subsequently in a field test of 1152 respondents in 7 European countries. The final condition-specific modules consist of an 'Impact' domain and an additional domain (e.g. worry, stigma, treatment) with between 10 to 12 items in total. The Cronbach's alpha of the final domains was found to vary from 0.71 to 0.90. Conclusion The condition-specific modules of the DISABKIDS instrument were developed through a step-by-step process including cognitive interview, clinical expertise, factor analysis, correlations and internal consistency. A cross-national pilot and field test were necessary to collect these data. In general, the internal consistency of the domains was satisfactory to high. In future, the DISABKIDS instrument may serve as a useful tool with which to assess HRQoL in children and adolescents with a chronic condition. The condition-specific modules can be used in conjunction with the DISABKIDS chronic generic module. PMID:16283947

The European DISABKIDS project: development of seven condition-specific modules to measure health related quality of life in children and adolescents.

PubMed

Baars, Rolanda M; Atherton, Clare I; Koopman, Hendrik M; Bullinger, Monika; Power, Mick

2005-11-13

The European DISABKIDS project aims to enhance the Health Related Quality of Life (HRQoL) of children and adolescents with chronic medical conditions and their families. We describe the development of the seven cross-nationally tested condition-specific modules of the European DISABKIDS HRQoL instrument in a population of children and adolescents. The condition-specific modules are intended for use in conjunction with the DISABKIDS chronic generic module. Focus groups were used to construct the pilot version of the DISABKIDS condition-specific HRQoL modules for asthma, juvenile idiopathic arthritis, atopic dermatitis, cerebral palsy, cystic fibrosis, diabetes and epilepsy. Analyses were conducted on pilot test data in order to construct field test versions of the modules. A series of factor analyses were run, first, to determine potential structures for each condition-specific module, and, secondly, to select a reduced number of items from the pilot test to be included in the field test. Post-field test analyses were conducted to retest the domain structure for the final DISABKIDS condition-specific modules. The DISABKIDS condition-specific modules were tested in a pilot study of 360 respondents, and subsequently in a field test of 1152 respondents in 7 European countries. The final condition-specific modules consist of an 'Impact' domain and an additional domain (e.g. worry, stigma, treatment) with between 10 to 12 items in total. The Cronbach's alpha of the final domains was found to vary from 0.71 to 0.90. The condition-specific modules of the DISABKIDS instrument were developed through a step-by-step process including cognitive interview, clinical expertise, factor analysis, correlations and internal consistency. A cross-national pilot and field test were necessary to collect these data. In general, the internal consistency of the domains was satisfactory to high. In future, the DISABKIDS instrument may serve as a useful tool with which to assess HRQoL in children and adolescents with a chronic condition. The condition-specific modules can be used in conjunction with the DISABKIDS chronic generic module.

Automated plasma control with optical emission spectroscopy

NASA Astrophysics Data System (ADS)

Ward, P. P.

Plasma etching and desmear processes for printed wiring board (PWB) manufacture are difficult to predict and control. Non-uniformity of most plasma processes and sensitivity to environmental changes make it difficult to maintain process stability from day to day. To assure plasma process performance, weight loss coupons or post-plasma destructive testing must be used. These techniques are not real-time methods however, and do not allow for immediate diagnosis and process correction. These tests often require scrapping some fraction of a batch to insure the integrity of the rest. Since these tests verify a successful cycle with post-plasma diagnostics, poor test results often determine that a batch is substandard and the resulting parts unusable. These tests are a costly part of the overall fabrication cost. A more efficient method of testing would allow for constant monitoring of plasma conditions and process control. Process anomalies should be detected and corrected before the parts being treated are damaged. Real time monitoring would allow for instantaneous corrections. Multiple site monitoring would allow for process mapping within one system or simultaneous monitoring of multiple systems. Optical emission spectroscopy conducted external to the plasma apparatus would allow for this sort of multifunctional analysis without perturbing the glow discharge. In this paper, optical emission spectroscopy for non-intrusive, in situ process control will be explored along with applications of this technique to for process control, failure analysis and endpoint determination in PWB manufacture.

Improvement of Stability and Antioxidant Activities by Using Phycocyanin - Chitosan Encapsulation Technique

NASA Astrophysics Data System (ADS)

Suzery, Meiny; Hadiyanto; Majid, Dian; Setyawan, Deny; Sutanto, Heri

2017-02-01

Encapsulation is a coating process to improve the stability of bioactive compounds. Phycocyanin with high antioxidant activity has been encapsulated with chitosan in microcapsules form. In this study aims to determine the best conditions in the encapsulation process using the extrusion method, characterization of the physicochemical properties of the microcapsules, antioxidant activity test using DPPH, in vitro release performance and evaluate the storage stability against temperature. The results of the encapsulation process is obtained: Na-TPP is better than Na-citrate as crosslinker and chitosan content 3% as a coating with ratio of chitosan to phycocyanin ratio 1: 1. Test of antioxidant activity also showed encapsulation with chitosan content 3% has the highest antioxidant activity. Morphological analysis microcapsules were found to have compact spherical shape with diameter range 900-1000 µm. In vitro release testing showed a quick release in an acidic environment (SGF) for 2 hours and slowly release under alkaline conditions (SIF) for 8 hours under mechanical stirring at 37°C. Phycocyanin much more stable against temperature during storage in microcapsules.

Strategic retrieval in a reality monitoring task.

PubMed

Rosburg, Timm; Mecklinger, Axel; Johansson, Mikael

2011-08-01

Strategic recollection refers to control processes that allow the retrieval of information that is relevant for a specific situation. These processes can be studied in memory exclusion tasks, which require the retrieval of particular kinds of episodic information. In the current study, we investigated strategic recollection in reality monitoring by event-related potentials (ERPs). Participants studied object words, followed by a picture of the denoted object (perceive condition) or followed by the instruction to imagine such a picture (imagine condition). At test, subjects had to identify words of one study condition and to reject words of the second study condition together with newly presented items. Data analysis showed that object names were better identified when items of the perceive condition were targeted. In this test condition, a left parietal old/new effect (the ERP correlate of recollection) was observed only in response to targets. In contrast, both targets and nontargets elicited this old/new effect when items of the imagine condition were targeted. The magnitude of the left parietal old/new effect to nontargets in this condition (but no other left parietal old/new effect) correlated positively with the discrimination indices of both test conditions. In addition, ERPs to targets and nontargets differed at right frontal electrode sites at longer latencies (1500-1800 ms), with more positive ERPs for targets. Findings indicate that subjects retrieved nontarget information in the more difficult task condition, while they relied on target information alone in the less difficult task. This kind of strategic retrieval was not mirrored in other old/new effects. The correlation between the left parietal old/new effect for nontargets in the imagined item target condition and the discrimination indices of both conditions may indicate that the ease of nontarget retrieval, rather than the difficulty of target retrieval, increases the likelihood that nontarget information is actually retrieved. Copyright © 2011 Elsevier Ltd. All rights reserved.

Titanium Nitride: An Oxidizable Coating for the High-Temperature Protection of Graphite

NASA Technical Reports Server (NTRS)

Wakelyn, N. T.

1961-01-01

A titanium nitride coating for graphite, prepared by deposition process, protected test specimens for 60 seconds the vapors in a supersonic ceramic-heated air jet with a stagnation temperature of approximately 2,250 K. For the same test conditions, coated specimens showed no damage to the graphite body for the 60-second test, whereas uncoated specimens were very severely damaged after 20 seconds and were destroyed toward the end of the test. A discussion of the coating of these graphite specimens and of some of the conditions necessary for the utilization of oxidizable substances as oxidation-protective coatings for bodies facing high convective heat transfer in the atmosphere is presented.

NASA's Evolutionary Xenon Thruster (NEXT) Component Verification Testing

NASA Technical Reports Server (NTRS)

Herman, Daniel A.; Pinero, Luis R.; Sovey, James S.

2009-01-01

Component testing is a critical facet of the comprehensive thruster life validation strategy devised by the NASA s Evolutionary Xenon Thruster (NEXT) program. Component testing to-date has consisted of long-duration high voltage propellant isolator and high-cycle heater life validation testing. The high voltage propellant isolator, a heritage design, will be operated under different environmental condition in the NEXT ion thruster requiring verification testing. The life test of two NEXT isolators was initiated with comparable voltage and pressure conditions with a higher temperature than measured for the NEXT prototype-model thruster. To date the NEXT isolators have accumulated 18,300 h of operation. Measurements indicate a negligible increase in leakage current over the testing duration to date. NEXT 1/2 in. heaters, whose manufacturing and control processes have heritage, were selected for verification testing based upon the change in physical dimensions resulting in a higher operating voltage as well as potential differences in thermal environment. The heater fabrication processes, developed for the International Space Station (ISS) plasma contactor hollow cathode assembly, were utilized with modification of heater dimensions to accommodate a larger cathode. Cyclic testing of five 1/22 in. diameter heaters was initiated to validate these modified fabrication processes while retaining high reliability heaters. To date two of the heaters have been cycled to 10,000 cycles and suspended to preserve hardware. Three of the heaters have been cycled to failure giving a B10 life of 12,615 cycles, approximately 6,000 more cycles than the established qualification B10 life of the ISS plasma contactor heaters.

Cultural differences in distraction processing: influence of context at retrieval.

PubMed

Ngo, Ka Wai Joan; Amer, Tarek; Man, Louisa; Hasher, Lynn

2018-06-04

Cultural differences in information processing affect perceptual judgment, attention, and memory. We investigated whether cultural differences in processing patterns, specifically East Asian participants' tendency to encode holistically, compared to Western tendencies to process analytically, affect performance on an implicit memory test. First, participants completed a 1-back task on pictures with superimposed distracting words. After a delay filled with a computerised Corsi block task, they performed a word fragment task in which some fragments could be completed with the distracting words from the 1-back task. Critically, fragments were presented with the same pictures as previously seen (matched condition), with no pictures (control condition), or with pictures from other trials on the 1-back task (mismatched condition). Non-Asian Canadian participants showed virtually no priming for distraction, independent of the reinstatement of encoding context. East Asian Canadian participants showed superior priming for fragments that had been paired with their original pictures. They did not show evidence of a detriment for the mismatched, relative to control, condition.

Poor sleep quality predicts deficient emotion information processing over time in early adolescence.

PubMed

Soffer-Dudek, Nirit; Sadeh, Avi; Dahl, Ronald E; Rosenblat-Stein, Shiran

2011-11-01

There is deepening understanding of the effects of sleep on emotional information processing. Emotion information processing is a key aspect of social competence, which undergoes important maturational and developmental changes in adolescence; however, most research in this area has focused on adults. Our aim was to test the links between sleep and emotion information processing during early adolescence. Sleep and facial information processing were assessed objectively during 3 assessment waves, separated by 1-year lags. Data were obtained in natural environments-sleep was assessed in home settings, and facial information processing was assessed at school. 94 healthy children (53 girls, 41 boys), aged 10 years at Time 1. N/A. Facial information processing was tested under neutral (gender identification) and emotional (emotional expression identification) conditions. Sleep was assessed in home settings using actigraphy for 7 nights at each assessment wave. Waking > 5 min was considered a night awakening. Using multilevel modeling, elevated night awakenings and decreased sleep efficiency significantly predicted poor performance only in the emotional information processing condition (e.g., b = -1.79, SD = 0.52, confidence interval: lower boundary = -2.82, upper boundary = -0.076, t(416.94) = -3.42, P = 0.001). Poor sleep quality is associated with compromised emotional information processing during early adolescence, a sensitive period in socio-emotional development.

Drinkers' memory bias for alcohol picture cues in explicit and implicit memory tasks.

PubMed

Nguyen-Louie, Tam T; Buckman, Jennifer F; Ray, Suchismita; Bates, Marsha E

2016-03-01

Alcohol cues can bias attention and elicit emotional reactions, especially in drinkers. Yet, little is known about how alcohol cues affect explicit and implicit memory processes, and how memory for alcohol cues is affected by acute alcohol intoxication. Young adult participants (N=161) were randomly assigned to alcohol, placebo, or control beverage conditions. Following beverage consumption, they were shown neutral, emotional and alcohol-related pictures cues. Participants then completed free recall and repetition priming tasks to test explicit and implicit memory, respectively, for picture cues. Average blood alcohol concentration for the alcohol group was 74±13mg/dl when memory testing began. Two mixed linear model analyses were conducted to examine the effects of beverage condition, picture cue type, and their interaction on explicit and implicit memory. Picture cue type and beverage condition each significantly affected explicit recall of picture cues, whereas only picture cue type significantly influenced repetition priming. Individuals in the alcohol condition recalled significantly fewer pictures than those in other conditions, regardless of cue type. Both free recall and repetition priming were greater for emotional and alcohol-related cues compared to neutral picture cues. No interaction effects were detected. Young adult drinkers showed enhanced explicit and implicit memory processing of alcohol cues compared to emotionally neutral cues. This enhanced processing for alcohol cues was on par with that seen for positive emotional cues. Acute alcohol intoxication did not alter this preferential memory processing for alcohol cues over neutral cues. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

FIELD TESTING AND EVALUATION OF ZERPOL® AT PIONEER METAL FINISHING

EPA Science Inventory

The project examines the Zerpol® process. The Zerpol® process, as used in metal plating operations, captures all aqueous effluent from the manufacturing operations, conditions the effluent to remove any metal or cyanide that may be present, and permits the reuse of the ...

Do European Standard Disinfectant tests truly simulate in-use microbial and organic soiling conditions on food preparation surfaces?

PubMed

Meyer, B; Morin, V N; Rödger, H-J; Holah, J; Bird, C

2010-04-01

The results from European standard disinfectant tests are used as one basis to approve the use of disinfectants in Europe. The design of these laboratory-based tests should thus simulate as closely as possible the practical conditions and challenges that the disinfectants would encounter in use. No evidence is available that the organic and microbial loading in these tests simulates actual levels in the food service sector. Total organic carbon (TOC) and total viable count (TVC) were determined on 17 visibly clean and 45 visibly dirty surfaces in two restaurants and the food preparation surfaces of a large retail store. These values were compared to reference values recovered from surfaces soiled with the organic and microbial loading, following the standard conditions of the European Surface Test for bactericidal efficacy, EN 13697. The TOC reference values for clean and dirty conditions were higher than the data from practice, but cannot be regarded as statistical outliers. This was considered as a conservative assessment; however, as additional nine TOC samples from visibly dirty surfaces were discarded from the analysis, as their loading made them impossible to process. Similarly, the recovery of test organisms from surfaces contaminated according to EN 13697 was higher than the TVC from visibly dirty surfaces in practice; though they could not be regarded as statistical outliers of the whole data field. No correlation was found between TVC and TOC in the sampled data, which re-emphasizes the potential presence of micro-organisms on visibly clean surfaces and thus the need for the same degree of disinfection as visibly dirty surfaces. The organic soil and the microbial burden used in EN disinfectant standards represent a realistic worst-case scenario for disinfectants used in the food service and food-processing areas.

Random Vibration Testing of Advanced Wet Tantalum Capacitors

NASA Technical Reports Server (NTRS)

Teverovsky, Alexander

2015-01-01

Advanced wet tantalum capacitors allow for improved performance of power supply systems along with substantial reduction of size and weight of the systems that is especially beneficial for space electronics. Due to launch-related stresses, acceptance testing of all space systems includes random vibration test (RVT). However, many types of advanced wet tantalum capacitors cannot pass consistently RVT at conditions specified in MIL-PRF-39006, which impedes their use in space projects. This requires a closer look at the existing requirements, modes and mechanisms of failures, specifics of test conditions, and acceptance criteria. In this work, different lots of advanced wet tantalum capacitors from four manufacturers have been tested at step stress random vibration conditions while their currents were monitored before, during, and after the testing. It has been shown that the robustness of the parts and their reliability are mostly due to effective self-healing processes and limited current spiking or minor scintillations caused by RVT do not increase the risk of failures during operation. A simple model for scintillations events has been used to simulate current spiking during RVT and optimize test conditions. The significance of scintillations and possible effects of gas generation have been discussed and test acceptance criteria for limited current spiking have been suggested.

Differentiation of subsequent memory effects between retrieval practice and elaborative study.

PubMed

Liu, Yi; Rosburg, Timm; Gao, Chuanji; Weber, Christine; Guo, Chunyan

2017-07-01

Retrieval practice enhances memory retention more than re-studying. The underlying mechanisms of this retrieval practice effect have remained widely unclear. According to the elaborative retrieval hypothesis, activation of elaborative information occurs to a larger extent during testing than re-studying. In contrast, the episodic context account has suggested that recollecting prior episodic information (especially the temporal context) contributes to memory retention. To adjudicate the distinction between these two accounts, the present study used the classical retrieval practice effect paradigm to compare retrieval practice and elaborative study. In an initial behavioral experiment, retrieval practice produced greater retention than elaboration and re-studying in a one-week delayed test. In a subsequent event-related potential (ERP) experiment, retrieval practice resulted in reliably superior accuracy in the delayed test compared to elaborative study. In the ERPs, a frontally distributed subsequent memory effect (SME), starting at 300ms, occurred in the elaborative study condition, but not in the retrieval practice condition. A parietal SME emerged in the retrieval practice condition from 500 to 700ms, but was absent in the elaborative study condition. After 700ms, a late SME was present in the retrieval practice condition, but not in the elaborative study condition. Moreover, SMEs lasted longer in retrieval practice than in elaboration. The frontal SME in the elaborative study condition might be related to semantic processing or working memory-based elaboration, whereas the parietal and widespread SME in the retrieval practice condition might be associated with episodic recollection processes. These findings contradict the elaborative retrieval theory, and suggest that contextual recollection rather than activation of semantic information contributes to the retrieval practice effect, supporting the episodic context account. Copyright © 2017. Published by Elsevier B.V.

In situ vitrification application to buried waste: Final report of intermediate field tests at Idaho National Engineering Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Callow, R.A.; Weidner, J.R.; Loehr, C.A.

This report describes two in situ vitrification field tests conducted on simulated buried waste pits during June and July 1990 at the Idaho National Engineering Laboratory. In situ vitrification, an emerging technology for in place conversion of contaminated soils into a durable glass and crystalline waste form, is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to access the general suitability of the process to remediate waste structures representative of buried waste found at Idaho National Engineering Laboratory. In particular, these tests, as part of a treatability study, were designedmore » to provide essential information on the field performance of the process under conditions of significant combustible and metal wastes and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology successfully processed the high metal content waste. Test results indicate the process is a feasible technology for application to buried waste. 33 refs., 109 figs., 39 tabs.« less

Prior cocaine exposure disrupts extinction of fear conditioning

PubMed Central

Burke, Kathryn A.; Franz, Theresa M.; Gugsa, Nishan; Schoenbaum, Geoffrey

2008-01-01

Psychostimulant exposure has been shown to cause molecular and cellular changes in prefrontal cortex. It has been hypothesized that these drug-induced changes might affect the operation of prefrontal-limbic circuits, disrupting their normal role in controlling behavior and thereby leading to compulsive drug-seeking. To test this hypothesis, we tested cocaine-treated rats in a fear conditioning, inflation, and extinction task, known to depend on medial prefrontal cortex and amygdala. Cocaine-treated rats conditioned and inflated similar to saline controls but displayed slower extinction learning. These results support the hypothesis that control processes in the medial prefrontal cortex are impaired by cocaine exposure. PMID:16847305

Prior cocaine exposure disrupts extinction of fear conditioning.

PubMed

Burke, Kathryn A; Franz, Theresa M; Gugsa, Nishan; Schoenbaum, Geoffrey

2006-01-01

Psychostimulant exposure has been shown to cause molecular and cellular changes in prefrontal cortex. It has been hypothesized that these drug-induced changes might affect the operation of prefrontal-limbic circuits, disrupting their normal role in controlling behavior and thereby leading to compulsive drug-seeking. To test this hypothesis, we tested cocaine-treated rats in a fear conditioning, inflation, and extinction task, known to depend on medial prefrontal cortex and amygdala. Cocaine-treated rats conditioned and inflated similar to saline controls but displayed slower extinction learning. These results support the hypothesis that control processes in the medial prefrontal cortex are impaired by cocaine exposure.

The neural substrates associated with attentional resources and difficulty of concurrent processing of the two verbal tasks.

PubMed

Mizuno, Kei; Tanaka, Masaaki; Tanabe, Hiroki C; Sadato, Norihiro; Watanabe, Yasuyoshi

2012-07-01

The kana pick-out test has been widely used in Japan to evaluate the ability to divide attention in both adult and pediatric patients. However, the neural substrates underlying the ability to divide attention using the kana pick-out test, which requires participants to pick out individual letters (vowels) in a story while also reading for comprehension, thus requiring simultaneous allocation of attention to both activities, are still unclear. Moreover, outside of the clinical area, neuroimaging studies focused on the mechanisms of divided attention during complex story comprehension are rare. Thus, the purpose of the present study, to clarify the neural substrates of kana pick-out test, improves our current understanding of the basic neural mechanisms of dual task performance in verbal memory function. We compared patterns of activation in the brain obtained during performance of the individual tasks of vowel identification and story comprehension, to levels of activation when participants performed the two tasks simultaneously during the kana pick-out test. We found that activations of the left dorsal inferior frontal gyrus and superior parietal lobule increase in functional connectivity to a greater extent during the dual task condition compared to the two single task conditions. In contrast, activations of the left fusiform gyrus and middle temporal gyrus, which are significantly involved in picking out letters and complex sentences during story comprehension, respectively, were reduced in the dual task condition compared to during the two single task conditions. These results suggest that increased activations of the dorsal inferior frontal gyrus and superior parietal lobule during dual task performance may be associated with the capacity for attentional resources, and reduced activations of the left fusiform gyrus and middle temporal gyrus may reflect the difficulty of concurrent processing of the two tasks. In addition, the increase in synchronization between the left dorsal inferior frontal gyrus and superior parietal lobule in the dual task condition may induce effective communication between these brain regions and contribute to more attentional processing than in the single task condition, due to greater and more complex demands on voluntary attentional resources. Copyright © 2012 Elsevier Ltd. All rights reserved.

Dynamic modeling and simulation of an integral bipropellant propulsion double-valve combined test system

NASA Astrophysics Data System (ADS)

Chen, Yang; Wang, Huasheng; Xia, Jixia; Cai, Guobiao; Zhang, Zhenpeng

2017-04-01

For the pressure reducing regulator and check valve double-valve combined test system in an integral bipropellant propulsion system, a system model is established with modular models of various typical components. The simulation research is conducted on the whole working process of an experiment of 9 MPa working condition from startup to rated working condition and finally to shutdown. Comparison of simulation results with test data shows: five working conditions including standby, startup, rated pressurization, shutdown and halt and nine stages of the combined test system are comprehensively disclosed; valve-spool opening and closing details of the regulator and two check valves are accurately revealed; the simulation also clarifies two phenomena which test data are unable to clarify, one is the critical opening state in which the check valve spools slightly open and close alternately in their own fully closed positions, the other is the obvious effects of flow-field temperature drop and temperature rise in pipeline network with helium gas flowing. Moreover, simulation results with consideration of component wall heat transfer are closer to the test data than those under the adiabatic-wall condition, and more able to reveal the dynamic characteristics of the system in various working stages.

A new method to assess Pavlovian conditioning of psychostimulant drug effects.

PubMed

Damianopoulos, E N; Carey, R J

1994-07-01

Experimental studies of psychoactive drugs by pavlovian drug-conditioning methods, which originally began with investigations of drug-induced responses mediated by the autonomic nervous system, have now been expanded to include drug-induced response effects expressed as modulations of spontaneous motoric behaviors. In the latter application, however, equivalent behavioral response outcomes in post-treatment tests for conditioning can occur following a psychostimulant drug treatment either through drug interference effects on habituation processes, drug-induced stress effects and/or by pavlovian conditioning of the drug-induced motoric activation effect. Current methodologies for the study of pavlovian conditioned drug effects and/or drug sensitization cannot distinguish among these possibilities. This methodological inadequacy was addressed by a modification of the conventional paired-unpaired treatment protocol. In the new protocol, the animal is sequentially placed into two test compartments with the drug treatment administered in conjunction with placement into the second test compartment. This design permits a differentiation of a pavlovian conditioned drug responses from non-conditioned drug effects through continuous measurement of the non-drug behavioral baseline in both the drug and non-drug control treatment groups combined with multiple response measurements and post-treatment tests for conditioning at variable post-conditioning intervals. The present study details the use of the new modified pavlovian protocol with repeated cocaine (10 mg/kg) treatment. A cocaine conditioned response at 1, 7, and 21 days post-conditioning was identified and distinguished from habituation and stress effects.

Characterization of Explosives Processing Waste Decomposition Due to Composting. Phase 2

DTIC Science & Technology

1992-11-01

with Ceriodaphnia (10 replicates, each containing 15 mL of test solution and one neonate ). In each temporal block of tests, Ceriodsnhnia survival and... neonate per replicate). This reference validated the biological quality of the dilution water, the Ceriodaphnia food, the test conditions (e.g...incubation temperature and photoperiod), and the health of the neonates used to initiate the tests. Information about the leachates, including the

Modeling of membrane processes for air revitalization and water recovery

NASA Technical Reports Server (NTRS)

Lange, Kevin E.; Foerg, Sandra L.; Dall-Bauman, Liese A.

1992-01-01

Gas-separation and reverse-osmosis membrane models are being developed in conjunction with membrane testing at NASA JSC. The completed gas-separation membrane model extracts effective component permeabilities from multicomponent test data, and predicts the effects of flow configuration, operating conditions, and membrane dimensions on module performance. Variable feed- and permeate-side pressures are considered. The model has been applied to test data for hollow-fiber membrane modules with simulated cabin-air feeds. Results are presented for a membrane designed for air drying applications. Extracted permeabilities are used to predict the effect of operating conditions on water enrichment in the permeate. A first-order reverse-osmosis model has been applied to test data for spiral wound membrane modules with a simulated hygiene water feed. The model estimates an effective local component rejection coefficient under pseudosteady-state conditions. Results are used to define requirements for a detailed reverse-osmosis model.

40 CFR 141.719 - Additional filtration toolbox components.

Code of Federal Regulations, 2011 CFR

2011-07-01

... establish a quality control release value (QCRV) for a non-destructive performance test that demonstrates... Detection Limit) (5) Challenge testing must be conducted at the maximum design flow rate for the filter as... representative hydraulic conditions at the maximum design flux and maximum design process recovery specified by...

40 CFR 141.719 - Additional filtration toolbox components.

Code of Federal Regulations, 2010 CFR

2010-07-01

... establish a quality control release value (QCRV) for a non-destructive performance test that demonstrates... Detection Limit) (5) Challenge testing must be conducted at the maximum design flow rate for the filter as... representative hydraulic conditions at the maximum design flux and maximum design process recovery specified by...

40 CFR 63.7520 - What stack tests and procedures must I use?

Code of Federal Regulations, 2011 CFR

2011-07-01

... Institutional Boilers and Process Heaters Testing, Fuel Analyses, and Initial Compliance Requirements § 63.7520... representative operating load conditions while burning the type of fuel or mixture of fuels that has the highest... measured hydrogen chloride concentrations, and the measured mercury concentrations that result from the...

Simultaneous face and voice processing in schizophrenia.

PubMed

Liu, Taosheng; Pinheiro, Ana P; Zhao, Zhongxin; Nestor, Paul G; McCarley, Robert W; Niznikiewicz, Margaret

2016-05-15

While several studies have consistently demonstrated abnormalities in the unisensory processing of face and voice in schizophrenia (SZ), the extent of abnormalities in the simultaneous processing of both types of information remains unclear. To address this issue, we used event-related potentials (ERP) methodology to probe the multisensory integration of face and non-semantic sounds in schizophrenia. EEG was recorded from 18 schizophrenia patients and 19 healthy control (HC) subjects in three conditions: neutral faces (visual condition-VIS); neutral non-semantic sounds (auditory condition-AUD); neutral faces presented simultaneously with neutral non-semantic sounds (audiovisual condition-AUDVIS). When compared with HC, the schizophrenia group showed less negative N170 to both face and face-voice stimuli; later P270 peak latency in the multimodal condition of face-voice relative to unimodal condition of face (the reverse was true in HC); reduced P400 amplitude and earlier P400 peak latency in the face but not in the voice-face condition. Thus, the analysis of ERP components suggests that deficits in the encoding of facial information extend to multimodal face-voice stimuli and that delays exist in feature extraction from multimodal face-voice stimuli in schizophrenia. In contrast, categorization processes seem to benefit from the presentation of simultaneous face-voice information. Timepoint by timepoint tests of multimodal integration did not suggest impairment in the initial stages of processing in schizophrenia. Published by Elsevier B.V.

Generalization of the photo process window and its application to OPC test pattern design

NASA Astrophysics Data System (ADS)

Eisenmann, Hans; Peter, Kai; Strojwas, Andrzej J.

2003-07-01

From the early development phase up to the production phase, test pattern play a key role for microlithography. The requirement for test pattern is to represent the design well and to cover the space of all process conditions, e.g. to investigate the full process window and all other process parameters. This paper shows that the current state-of-the-art test pattern do not address these requirements sufficiently and makes suggestions for a better selection of test pattern. We present a new methodology to analyze an existing layout (e.g. logic library, test pattern or full chip) for critical layout situations which does not need precise process data. We call this method "process space decomposition", because it is aimed at decomposing the process impact to a layout feature into a sum of single independent contributions, the dimensions of the process space. This is a generalization of the classical process window, which examines defocus and exposure dependency of given test pattern, e.g. CD value of dense and isolated lines. In our process space we additionally define the dimensions resist effects, etch effects, mask error and misalignment, which describe the deviation of the printed silicon pattern from its target. We further extend it by the pattern space using a product based layout (library, full chip or synthetic test pattern). The criticality of pattern is defined by their deviation due to aerial image, their sensitivity to the respective dimension or several combinations of these. By exploring the process space for a given design, the method allows to find the most critical patterns independent of specific process parameters. The paper provides examples for different applications of the method: (1) selection of design oriented test pattern for lithography development (2) test pattern reduction in process characterization (3) verification/optimization of printability and performance of post processing procedures (like OPC) (4) creation of a sensitive process monitor.

Vacuum Baking To Remove Volatile Materials

NASA Technical Reports Server (NTRS)

Muscari, J. A.

1985-01-01

Outgassing reduced in some but not all nonmetallic materials. Eleven polymeric materials tested by determining outgassing species as temperature of conditioned and unconditioned materials raised to 300 degrees C. Conditioning process consisted of vacuum bake for 24 hours at 80 degrees C in addition to usual cure. Baking did not change residual gas percentage of water molecules.

A Peer Assessment System to Improve Student Team Experiences

ERIC Educational Resources Information Center

Anson, Robert; Goodman, James A.

2014-01-01

Groups are frequently used in courses, but there is substantial evidence that insufficient attention is paid to creating conditions for successful teamwork. One key condition is high-quality, individual, and team-level feedback. An online peer assessment system and team improvement process was developed for this test case based on three design…

[Predictive power of working memory task for reading comprehension: an investigation using reading span test].

PubMed

Morishita, Masanao; Kondo, Hirohito; Ashida, Kayo; Otsuka, Yuki; Osaka, Naoyuki

2007-02-01

This study investigated the crucial factor mediating a correlation between performance of reading span test (RST) and reading comprehension. In the research literature on this issue, one of the remaining controversial points is whether the similarity of sentence processing between RST and comprehension contributes to the correlation. In this study, four RST conditions were created by the combination of two factors: relatedness of stimulus sentences (related or unrelated with each other) and focus of target words (focus or non-focus with respect to sentence meaning). If the correlation is mediated by the similarity of sentence processing, RST performance of related and focus condition, which was most akin to comprehension, would have higher correlation with reading comprehension than other conditions. However, as a result of correlation analysis based on data from ninety-six participants, no such evidence was obtained. On the other hand, RST performance of unrelated conditions that were supposed to strongly require attention control showed significant correlation with reading comprehension. These findings are discussed in terms of the contribution of attention control and short-term memory to performing RST and reading comprehension.

New method of processing heat treatment experiments with numerical simulation support

NASA Astrophysics Data System (ADS)

Kik, T.; Moravec, J.; Novakova, I.

2017-08-01

In this work, benefits of combining modern software for numerical simulations of welding processes with laboratory research was described. Proposed new method of processing heat treatment experiments leading to obtaining relevant input data for numerical simulations of heat treatment of large parts was presented. It is now possible, by using experiments on small tested samples, to simulate cooling conditions comparable with cooling of bigger parts. Results from this method of testing makes current boundary conditions during real cooling process more accurate, but also can be used for improvement of software databases and optimization of a computational models. The point is to precise the computation of temperature fields for large scale hardening parts based on new method of temperature dependence determination of the heat transfer coefficient into hardening media for the particular material, defined maximal thickness of processed part and cooling conditions. In the paper we will also present an example of the comparison standard and modified (according to newly suggested methodology) heat transfer coefficient data’s and theirs influence on the simulation results. It shows how even the small changes influence mainly on distribution of temperature, metallurgical phases, hardness and stresses distribution. By this experiment it is also possible to obtain not only input data and data enabling optimization of computational model but at the same time also verification data. The greatest advantage of described method is independence of used cooling media type.

Bow Your Head in Shame, or, Hold Your Head Up with Pride: Semantic Processing of Self-Esteem Concepts Orients Attention Vertically.

PubMed

Taylor, J Eric T; Lam, Timothy K; Chasteen, Alison L; Pratt, Jay

2015-01-01

Embodied cognition holds that abstract concepts are grounded in perceptual-motor simulations. If a given embodied metaphor maps onto a spatial representation, then thinking of that concept should bias the allocation of attention. In this study, we used positive and negative self-esteem words to examine two properties of conceptual cueing. First, we tested the orientation-specificity hypothesis, which predicts that conceptual cues should selectively activate certain spatial axes (in this case, valenced self-esteem concepts should activate vertical space), instead of any spatial continuum. Second, we tested whether conceptual cueing requires semantic processing, or if it can be achieved with shallow visual processing of the cue words. Participants viewed centrally presented words consisting of high or low self-esteem traits (e.g., brave, timid) before detecting a target above or below the cue in the vertical condition, or on the left or right of the word in the horizontal condition. Participants were faster to detect targets when their location was compatible with the valence of the word cues, but only in the vertical condition. Moreover, this effect was observed when participants processed the semantics of the word, but not when processing its orthography. The results show that conceptual cueing by spatial metaphors is orientation-specific, and that an explicit consideration of the word cues' semantics is required for conceptual cueing to occur.

False memory and level of processing effect: an event-related potential study.

PubMed

Beato, Maria Soledad; Boldini, Angela; Cadavid, Sara

2012-09-12

Event-related potentials (ERPs) were used to determine the effects of level of processing on true and false memory, using the Deese-Roediger-McDermott (DRM) paradigm. In the DRM paradigm, lists of words highly associated to a single nonpresented word (the 'critical lure') are studied and, in a subsequent memory test, critical lures are often falsely remembered. Lists with three critical lures per list were auditorily presented here to participants who studied them with either a shallow (saying whether the word contained the letter 'o') or a deep (creating a mental image of the word) processing task. Visual presentation modality was used on a final recognition test. True recognition of studied words was significantly higher after deep encoding, whereas false recognition of nonpresented critical lures was similar in both experimental groups. At the ERP level, true and false recognition showed similar patterns: no FN400 effect was found, whereas comparable left parietal and late right frontal old/new effects were found for true and false recognition in both experimental conditions. Items studied under shallow encoding conditions elicited more positive ERP than items studied under deep encoding conditions at a 1000-1500 ms interval. These ERP results suggest that true and false recognition share some common underlying processes. Differential effects of level of processing on true and false memory were found only at the behavioral level but not at the ERP level.

Dual learning processes in interactive skill acquisition.

PubMed

Fu, Wai-Tat; Anderson, John R

2008-06-01

Acquisition of interactive skills involves the use of internal and external cues. Experiment 1 showed that when actions were interdependent, learning was effective with and without external cues in the single-task condition but was effective only with the presence of external cues in the dual-task condition. In the dual-task condition, actions closer to the feedback were learned faster than actions farther away but this difference was reversed in the single-task condition. Experiment 2 tested how knowledge acquired in single and dual-task conditions would transfer to a new reward structure. Results confirmed the two forms of learning mediated by the secondary task: A declarative memory encoding process that simultaneously assigned credits to actions and a reinforcement-learning process that slowly propagated credits backward from the feedback. The results showed that both forms of learning were engaged during training, but only at the response selection stage, one form of knowledge may dominate over the other depending on the availability of attentional resources. (c) 2008 APA, all rights reserved

2009 Continued Testing of the Orion Atmosphere Revitalization Technology

NASA Technical Reports Server (NTRS)

Button, Amy B.; Swerterlitsch, Jeffrey J.

2010-01-01

An amine-based carbon dioxide (CO2) and water vapor sorbent in pressure-swing regenerable beds has been developed by Hamilton Sundstrand and baselined for the Orion Atmosphere Revitalization System (ARS). In three previous years at this conference, reports were presented on extensive Johnson Space Center (JSC) testing of this technology in a sea-level pressure environment, with simulated and real human metabolic loads, in both open and closed-loop configurations. The test article design was iterated a third time before the latest series of such tests, which was performed in the first half of 2009. The new design incorporates a canister configuration modification for overall unit compactness and reduced pressure drop, as well as a new process flow control valve that incorporates both compressed gas purge and dual-end vacuum desorption capabilities. This newest test article is very similar to the flight article designs. Baseline tests of the new unit were performed to compare its performance to that of the previous test articles. Testing of compressed gas purge operations helped refine launchpad operating condition recommendations developed in earlier testing. Operating conditions used in flight program computer models were tested to validate the model projections. Specific operating conditions that were recommended by the JSC test team based on past test results were also tested for validation. The effects of vacuum regeneration line pressure on resulting cabin conditions was studied for high metabolic load periods, and a maximum pressure is recommended

2009 Continued Testing of the Orion Atmosphere Revitalization Technology

NASA Technical Reports Server (NTRS)

Button, Amy Lin; Sweterlitsch, Jeffrey

2009-01-01

An amine-based carbon dioxide (CO2) and water vapor sorbent in pressure-swing regenerable beds has been developed by Hamilton Sundstrand and baselined for the Orion Atmosphere Revitalization System (ARS). In three previous years at this conference, reports were presented on extensive Johnson Space Center (JSC) testing of this technology in a sea-level pressure environment with simulated and real human metabolic loads in both open and closed-loop configurations. The test article design was iterated a third time before the latest series of such tests, which was performed in the first half of 2009. The new design incorporates a canister configuration modification for overall unit compactness and reduced pressure drop, as well as a new process flow control valve that incorporates both compressed gas purge and dual-end vacuum desorption capabilities. This newest test article is very similar to the flight article designs. Baseline tests of the new unit were performed to compare its performance to that of the previous test articles. Testing of compressed gas purge operations helped refine launchpad operating condition recommendations developed in earlier testing. Operating conditions used in flight program computer models were tested to validate the model projections. Specific operating conditions that were recommended by the JSC test team based on past test results were also tested for validation. The effects of vacuum regeneration line pressure on resulting cabin conditions was studied for high metabolic load periods, and a maximum pressure is recommended.

The Impact of Flagging on the Admission Process.

ERIC Educational Resources Information Center

Cahalan-Laitusis, Cara; Mandinach, Ellen B.; Camara, Wayne J.

2003-01-01

Study explored issues surrounding flagging test scores taken under non-standard conditions and how the admission process could better serve students with disabilities. Respondents to survey felt current system was not adequately serving subgroups of students, believing some non-disabled students were manipulating the system to gain an advantage on…

Potential Use of BEST® Sediment Trap in Splash - Saltation Transport Process by Simultaneous Wind and Rain Tests.

PubMed

Basaran, Mustafa; Uzun, Oguzhan; Cornelis, Wim; Gabriels, Donald; Erpul, Gunay

2016-01-01

The research on wind-driven rain (WDR) transport process of the splash-saltation has increased over the last twenty years as wind tunnel experimental studies provide new insights into the mechanisms of simultaneous wind and rain (WDR) transport. The present study was conducted to investigate the efficiency of the BEST® sediment traps in catching the sand particles transported through the splash-saltation process under WDR conditions. Experiments were conducted in a wind tunnel rainfall simulator facility with water sprayed through sprinkler nozzles and free-flowing wind at different velocities to simulate the WDR conditions. Not only for vertical sediment distribution, but a series of experimental tests for horizontal distribution of sediments was also performed using BEST® collectors to obtain the actual total sediment mass flow by the splash-saltation in the center of the wind tunnel test section. Total mass transport (kg m-2) were estimated by analytically integrating the exponential functional relationship using the measured sediment amounts at the set trap heights for every run. Results revealed the integrated efficiency of the BEST® traps at 6, 9, 12 and 15 m s-1 wind velocities under 55.8, 50.5, 55.0 and 50.5 mm h-1 rain intensities were, respectively, 83, 106, 105, and 102%. Results as well showed that the efficiencies of BEST® did not change much as compared with those under rainless wind condition.

Optimizing the pre-referral workup for gastroenterology and hepatology specialty care: consensus using the Delphi method.

PubMed

Ho, Chanda K; Boscardin, Christy K; Gleason, Nathaniel; Collado, Don; Terdiman, Jonathan; Terrault, Norah A; Gonzales, Ralph

2016-02-01

Specialty care referrals have doubled in the last decade. Optimization of the pre-referral workup by a primary care doctor can lead to a more efficient first specialty visit with the patient. Guidance regarding pre-referral laboratory testing is a first step towards improving the specialty referral process. Our aim was to establish consensus regarding appropriate pre-referral workup for common gastrointestinal and liver conditions. The Delphi method was used to establish local consensus for recommending certain laboratory tests prior to specialty referral for 13 clinical conditions. Seven conditions from The University of Michigan outpatient referral guidelines were used as a baseline. An expert panel of three PCPs and nine gastroenterologists from three academic hospitals participated in three iterative rounds of electronic surveys. Each panellist ranked each test using a 5-point Likert scale (strongly disagree to strongly agree). Local panellists could recommend additional tests for the initial diagnoses, and also recommended additional diagnoses needing guidelines: iron deficiency anaemia, abdominal pain, irritable bowel syndrome, fatty liver disease, liver mass and cirrhosis. Consensus was defined as ≥70% of experts scoring ≥4 (agree or strongly agree). Applying Delphi methodology to extrapolate externally developed referral guidelines for local implementation resulted in considerable modifications. For some conditions, many tests from the external group were eliminated by the local group (abdominal bloating; iron deficiency anaemia; irritable bowel syndrome). In contrast, for chronic diarrhoea, abnormal liver enzymes and viral hepatitis, all/most original tests were retained with additional tests added. For liver mass, fatty liver disease and cirrhosis, there was high concordance among the panel with few tests added or eliminated. Consideration of externally developed referral guidelines using a consensus-building process leads to significant local tailoring and adaption. Our next steps include implementation and dissemination of these guidelines and evaluating their impact on care efficiency in clinical practice. © 2015 John Wiley & Sons, Ltd.

Monitoring TCE Degradation by In-situ Bioremediation in TCE-Contaminated site

NASA Astrophysics Data System (ADS)

Han, K.; Hong, U.; Ahn, G.; Jiang, H.; Yoo, H.; Park, S.; Kim, N.; Ahn, H.; Kwon, S.; Kim, Y.

2012-12-01

Trichloroethylene (TCE) is a long-term common groundwater pollutant because the compound with high density is slowly released into groundwater. Physical and chemical remediation processes have been used to clean-up the contaminant, but novel remediation technology is required to overcome a low efficiency of the traditional treatment process. Many researchers focused on biological process using an anaerobic TCE degrading culture, but it still needs to evaluate whether the process can be applied into field scale under aerobic condition. Therefore, in this work we investigated two different tests (i.e., biostimulation and bioaugmentation) of biological remediation through the Well-to-Well test (injection well to extraction well) in TCE-contaminated site. Also solutions (Electron donor & acceptor, tracer) were injected into the aquifer using a liquid coupled with nitrogen gas sparging. In biostimulation, we use 3 phases to monitoring biological remediation. Phase 1: we inject formate solution to get electron donor hydrogen (hydrogen can be generated from fermentation of formate). We also inject bromide as tracer. Phase 2: we made injection solution by formate, bromide and sulfate. The reason why we inject sulfate is that as a kind of electron accepter, sulfate reduction process is helpful to create anaerobic condition. Phase 3: we inject mixed solution made by formate, sulfate, fumarate, and bromide. The degradation of fumarate has the same mechanism and condition with TCE degradation, so we added fumarate to make sure that if the anaerobic TCE degradation by indigenous microorganisms started up (Because low TCE concentration by gas sparging). In the bioaugmentation test, we inject the Evanite culture (containing dehalococcoides spp) and TCE degradation to c-DCE, VC, ETH was monitored. We are evaluating the transport of the Evanite culture in the field by measuring TCE and VC reductases.

42 CFR 85.5 - Authority for investigations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... investigations of all pertinent processes, conditions, structures, machines, apparatus, devices, equipment... measurements, and functional tests of employees within the place of employment as may be directly related to...

A processing approach to the working memory/long-term memory distinction: evidence from the levels-of-processing span task.

PubMed

Rose, Nathan S; Craik, Fergus I M

2012-07-01

Recent theories suggest that performance on working memory (WM) tasks involves retrieval from long-term memory (LTM). To examine whether WM and LTM tests have common principles, Craik and Tulving's (1975) levels-of-processing paradigm, which is known to affect LTM, was administered as a WM task: Participants made uppercase, rhyme, or category-membership judgments about words, and immediate recall of the words was required after every 3 or 8 processing judgments. In Experiment 1, immediate recall did not demonstrate a levels-of-processing effect, but a subsequent LTM test (delayed recognition) of the same words did show a benefit of deeper processing. Experiment 2 showed that surprise immediate recall of 8-item lists did demonstrate a levels-of-processing effect, however. A processing account of the conditions in which levels-of-processing effects are and are not found in WM tasks was advanced, suggesting that the extent to which levels-of-processing effects are similar between WM and LTM tests largely depends on the amount of disruption to active maintenance processes. 2012 APA, all rights reserved

Brief Report: Joint Attention and Information Processing in Children with Higher Functioning Autism Spectrum Disorders.

PubMed

Mundy, Peter; Kim, Kwanguk; McIntyre, Nancy; Lerro, Lindsay; Jarrold, William

2016-07-01

Theory suggests that information processing during joint attention may be atypical in children with Autism Spectrum Disorder (ASD). This hypothesis was tested in a study of school-aged children with higher functioning ASD and groups of children with symptoms of ADHD or typical development. The results indicated that the control groups displayed significantly better recognition memory for pictures studied in an initiating joint attention (IJA) rather than responding to joint attention (RJA) condition. This effect was not evident in the ASD group. The ASD group also recognized fewer pictures from the IJA condition than controls, but not the RJA condition. Atypical information processing may be a marker of the continued effects of joint attention disturbance in school aged children with ASD.

Wear behavior of carbonitride-treated ploughshares produced from 30MnB5 steel for soil tillage applications

NASA Astrophysics Data System (ADS)

Yazici, A.

2011-09-01

The effects of gaseous carbonitriding processes on wear characteristics of 30MnB5 steel were investigated. The matrix of the carbonitride treated samples has a better wear resistance compared to the substrates of the conventionally heat-treated sample in laboratory conditions. The carbonitriding treatment condition giving rise to the lowest wear weight loss with the pin-on-disc wear machine was selected in order to harden ploughshare specimens to be tested in field experiments. The carbonitriding process at 860°C, with 0.9% C, and 0.6 m3/h NH3 for 105 min and quenched in 60°C oil followed by a 60 min tempering process at 140°C decreased 14.65% of total wear weight loss and 26.47% of total wear dimension loss of the ploughshare specimens in comparison to the conventional heat treatment process in field operational conditions.

Space Shuttle Main Engine Low Pressure Oxidizer Turbo-Pump Inducer Dynamic Environment Characterization through Water Model and Hot-Fire Testing

NASA Technical Reports Server (NTRS)

Arellano, Patrick; Patton, Marc; Schwartz, Alan; Stanton, David

2006-01-01

The Low Pressure Oxidizer Turbopump (LPOTP) inducer on the Block II configuration Space Shuttle Main Engine (SSME) experienced blade leading edge ripples during hot firing. This undesirable condition led to a minor redesign of the inducer blades. This resulted in the need to evaluate the performance and the dynamic environment of the redesign, relative to the current configuration, as part of the design acceptance process. Sub-scale water model tests of the two inducer configurations were performed, with emphasis on the dynamic environment due to cavitation induced vibrations. Water model tests were performed over a wide range of inlet flow coefficient and pressure conditions, representative of the scaled operating envelope of the Block II SSME, both in flight and in ground hot-fire tests, including all power levels. The water test hardware, facility set-up, type and placement of instrumentation, the scope of the test program, specific test objectives, data evaluation process and water test results that characterize and compare the two SSME LPOTP inducers are discussed. In addition, dynamic characteristics of the two water models were compared to hot fire data from specially instrumented ground tests. In general, good agreement between the water model and hot fire data was found, which confirms the value of water model testing for dynamic characterization of rocket engine turbomachinery.

Assessment of JVX Proprotor Performance Data in Hover and Airplane-Mode Flight Conditions

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.

2016-01-01

A 0.656-scale V-22 proprotor, the Joint Vertical Experimental (JVX) rotor, was tested at the NASA Ames Research Center in both hover and airplane-mode (high-speed axial flow) flight conditions, up to an advance ratio of 0.562 (231 knots). This paper examines the two principal data sets generated by those tests, and includes investigations of hub spinner tares, torque/thrust measurement interactions, tunnel blockage effects, and other phenomena suspected of causing erroneous measurements or predictions. Uncertainties in hover and high-speed data are characterized. The results are reported here to provide guidance for future wind tunnel tests, data processing, and data analysis.

Auditory Processing Testing: In the Booth versus Outside the Booth.

PubMed

Lucker, Jay R

2017-09-01

Many audiologists believe that auditory processing testing must be carried out in a soundproof booth. This expectation is especially a problem in places such as elementary schools. Research comparing pure-tone thresholds obtained in sound booths compared to quiet test environments outside of these booths does not support that belief. Auditory processing testing is generally carried out at above threshold levels, and therefore may be even less likely to require a soundproof booth. The present study was carried out to compare test results in soundproof booths versus quiet rooms. The purpose of this study was to determine whether auditory processing tests can be administered in a quiet test room rather than in the soundproof test suite. The outcomes would identify that audiologists can provide auditory processing testing for children under various test conditions including quiet rooms at their school. A battery of auditory processing tests was administered at a test level equivalent to 50 dB HL through headphones. The same equipment was used for testing in both locations. Twenty participants identified with normal hearing were included in this study, ten having no auditory processing concerns and ten exhibiting auditory processing problems. All participants underwent a battery of tests, both inside the test booth and outside the booth in a quiet room. Order of testing (inside versus outside) was counterbalanced. Participants were first determined to have normal hearing thresholds for tones and speech. Auditory processing tests were recorded and presented from an HP EliteBook laptop computer with noise-canceling headphones attached to a y-cord that not only presented the test stimuli to the participants but also allowed monitor headphones to be worn by the evaluator. The same equipment was used inside as well as outside the booth. No differences were found for each auditory processing measure as a function of the test setting or the order in which testing was done, that is, in the booth or in the room. Results from the present study indicate that one can obtain the same results on auditory processing tests, regardless of whether testing is completed in a soundproof booth or in a quiet test environment. Therefore, audiologists should not be required to test for auditory processing in a soundproof booth. This study shows that audiologists can conduct testing in a quiet room so long as the background noise is sufficiently controlled. American Academy of Audiology

The beneficial effect of testing: an event-related potential study

PubMed Central

Bai, Cheng-Hua; Bridger, Emma K.; Zimmer, Hubert D.; Mecklinger, Axel

2015-01-01

The enhanced memory performance for items that are tested as compared to being restudied (the testing effect) is a frequently reported memory phenomenon. According to the episodic context account of the testing effect, this beneficial effect of testing is related to a process which reinstates the previously learnt episodic information. Few studies have explored the neural correlates of this effect at the time point when testing takes place, however. In this study, we utilized the ERP correlates of successful memory encoding to address this issue, hypothesizing that if the benefit of testing is due to retrieval-related processes at test then subsequent memory effects (SMEs) should resemble the ERP correlates of retrieval-based processing in their temporal and spatial characteristics. Participants were asked to learn Swahili-German word pairs before items were presented in either a testing or a restudy condition. Memory performance was assessed immediately and 1-day later with a cued recall task. Successfully recalling items at test increased the likelihood that items were remembered over time compared to items which were only restudied. An ERP subsequent memory contrast (later remembered vs. later forgotten tested items), which reflects the engagement of processes that ensure items are recallable the next day were topographically comparable with the ERP correlate of immediate recollection (immediately remembered vs. immediately forgotten tested items). This result shows that the processes which allow items to be more memorable over time share qualitatively similar neural correlates with the processes that relate to successful retrieval at test. This finding supports the notion that testing is more beneficial than restudying on memory performance over time because of its engagement of retrieval processes, such as the re-encoding of actively retrieved memory representations. PMID:26441577

Study of thermocline development inside a dual-media storage tank at the beginning of dynamic processes

NASA Astrophysics Data System (ADS)

Esence, Thibaut; Bayón, Rocío; Bruch, Arnaud; Rojas, Esther

2017-06-01

This work presents some of the experimental results obtained during a test campaign performed at the STONE facility of CEA-Grenoble in collaboration with CIEMAT-PSA supported by both the SFERA-II and the STAGE-STE project. This installation consists of a thermocline tank with thermal oil and rock/sand filler and the tests aimed to study the development of the temperature profile inside the tank at the beginning of charge/discharge processes. The investigation of how this profile is created and which is its dependence on the experimental parameters is crucial for predicting the behavior of a dual-media thermocline tank. Tests have been performed for dynamic processes from initial states with constant uniform temperature or with a thermal gradient already present due to a partial thermocline zone extraction in the former process. Tests at different fluid velocities and temperatures have been carried out as well, in order to evaluate the influence of operating conditions. When a dynamic process of charge or discharge is started, the development of the thermal front is very sharp and localized at tank top or bottom if initial tank temperature is uniform, whereas it is less pronounced if the test begins from a non-thermally uniform initial state. In terms of operating conditions, it has been observed that the development of the thermocline thermal front is independent not only of the fluid velocity but also of its temperatures, within the working ranges here considered. Due to these experimental results, it will be possible to improve simulation models for thermocline tanks and hence to predict their behavior more accurately, especially when they are implemented in annual simulations of CSP plants.

Redox Control For Hanford HLW Feeds VSL-12R2530-1, REV 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, A. A.; Matlack, Keith S.; Pegg, Ian L.

2012-12-13

The principal objectives of this work were to investigate the effects of processing simulated Hanford HLW at the estimated maximum concentrations of nitrates and oxalates and to identify strategies to mitigate any processing issues resulting from high concentrations of nitrates and oxalates. This report provides results for a series of tests that were performed on the DM10 melter system with simulated C-106/AY-102 HLW. The tests employed simulated HLW feeds containing variable amounts of nitrates and waste organic compounds corresponding to maximum concentrations proj ected for Hanford HLW streams in order to determine their effects on glass production rate, processing characteristics,more » glass redox conditions, melt pool foaming, and the tendency to form secondary phases. Such melter tests provide information on key process factors such as feed processing behavior, dynamic effects during processing, processing rates, off-gas amounts and compositions, foaming control, etc., that cannot be reliably obtained from crucible melts.« less

RSRM Nozzle Anomalous Throat Erosion Investigation Overview

NASA Technical Reports Server (NTRS)

Clinton, R. G., Jr.; Wendel, Gary M.

1998-01-01

In September, 1996, anomalous pocketing erosion was observed in the aft end of the throat ring of the nozzle of one of the reusable solid rocket motors (RSRM 56B) used on NASA's space transportation system (STS) mission 79. The RSRM throat ring is constructed of bias tape-wrapped carbon cloth/ phenolic (CCP) ablative material. A comprehensive investigation revealed necessary and sufficient conditions for occurrence of the pocketing event and provided rationale that the solid rocket motors for the subsequent mission, STS-80, were safe to fly. The nozzles of both of these motors also exhibited anomalous erosion similar to, but less extensive than that observed on STS-79. Subsequent to this flight, the investigation to identify both the specific causes and the corrective actions for elimination of the necessary and sufficient conditions for the pocketing erosion was intensified. A detailed fault tree approach was utilized to examine potential material and process contributors to the anomalous performance. The investigation involved extensive constituent and component material property testing, pedigree assessments, supplier audits, process audits, full scale processing test article fabrication and evaluation, thermal and thermostructural analyses, nondestructive evaluation, and material performance tests conducted using hot fire simulation in laboratory test beds and subscale and full scale solid rocket motor static test firings. This presentation will provide an over-view of the observed anomalous nozzle erosion and the comprehensive, fault-tree based investigation conducted to resolve this issue.

Hot Deformation Behavior of Hot-Extruded AA7175 Through Hot Torsion Tests.

PubMed

Lee, Se-Yeon; Jung, Taek-Kyun; Son, Hyeon-Woo; Kim, Sang-Wook; Son, Kwang-Tae; Choi, Ho-Joon; Oh, Sang-Ho; Lee, Ji-Woon; Hyun, Soong-Keun

2018-03-01

The hot deformation behavior of hot-extruded AA7175 was investigated with flow curves and processing maps through hot torsion tests. The flow curves and the deformed microstructures revealed that dynamic recrystallization (DRX) occurred in the hot-extruded AA7175 during hot working. The failure strain was highest at medium temperature. This was mainly influenced by the dynamic precipitation of fine rod-shaped MgZn2. The processing map determined the optimal deformation condition for the alloy during hot working.

Determination of Pressure Fluctuations in Rotor Bundle of Centrifugal Compressor at Critical Conditions of Operation

NASA Astrophysics Data System (ADS)

Levashov, V. A.; Lyubchenko, K. Yu

2017-08-01

This article describes the physical processes that occur in the stage flow part of the compressor while it is operating and can create conditions for the occurrence of forced vibrations, which in turn can lead to the destruction of the impellers. Critical conditions of compressor operation are determined. To understand that critical condition of operation is cause of the destruction of the impellers, transient CFD analysis was carried for test stage of compressor. The obtained pressure fluctuation amplitudes allow to evaluate the critical conditions of compressor operation.

Lateralized implicit sequence learning in uni- and bi-manual conditions.

PubMed

Schmitz, Rémy; Pasquali, Antoine; Cleeremans, Axel; Peigneux, Philippe

2013-02-01

It has been proposed that the right hemisphere (RH) is better suited to acquire novel material whereas the left hemisphere (LH) is more able to process well-routinized information. Here, we ask whether this potential dissociation also manifests itself in an implicit learning task. Using a lateralized version of the serial reaction time task (SRT), we tested whether participants trained in a divided visual field condition primarily stimulating the RH would learn the implicit regularities embedded in sequential material faster than participants in a condition favoring LH processing. In the first study, half of participants were presented sequences in the left (vs. right) visual field, and had to respond using their ipsilateral hand (unimanual condition), hence making visuo-motor processing possible within the same hemisphere. Results showed successful implicit sequence learning, as indicated by increased reaction time for a transfer sequence in both hemispheric conditions and lack of conscious knowledge in a generation task. There was, however, no evidence of interhemispheric differences. In the second study, we hypothesized that a bimanual response version of the lateralized SRT, which requires interhemispheric communication and increases computational and cognitive processing loads, would favor RH-dependent visuospatial/attentional processes. In this bimanual condition, our results revealed a much higher transfer effect in the RH than in the LH condition, suggesting higher RH sensitivity to the processing of novel sequential material. This LH/RH difference was interpreted within the framework of the Novelty-Routinization model [Goldberg, E., & Costa, L. D. (1981). Hemisphere differences in the acquisition and use of descriptive systems. Brain and Language, 14(1), 144-173] and interhemispheric interactions in attentional processing [Banich, M. T. (1998). The missing link: the role of interhemispheric interaction in attentional processing. Brain and Cognition, 36(2), 128-157]. Copyright © 2012 Elsevier Inc. All rights reserved.

Fluidised-bed spray-drying formulations of Candida sake CPA-1 by adding biodegradable coatings to enhance their survival under stress conditions.

PubMed

Carbó, Anna; Torres, Rosario; Usall, Josep; Solsona, Cristina; Teixidó, Neus

2017-11-01

The biocontrol agent Candida sake CPA-1 has demonstrated to be effective against several diseases on fruit. However, for application of CPA-1 under field conditions, it was necessary to mix it with a food coating to improve survival under stress conditions, as well as adherence and distribution on fruit surfaces. The objective of this study was to obtain a more competitive formulation under field conditions to be applied independently of any product. To achieve this purpose, the drying process of CPA-1 by a fluidised-bed spray-drying system together with biodegradable coatings was optimised. This approach is novel for the drying system used and the formulation obtained which was able to form a film or coating on fruit surfaces. Several substances were tested as carriers and binders, and drying temperature was optimised. The addition of protective compounds was also tested to improve survival of CPA-1 during the dehydration process. Product shelf life, biocontrol efficacy on grapes against Botrytis cinerea, and the improvement of C. sake behaviour under stress conditions were tested. The optimal temperature of drying was 55 °C and two formulations that were able to develop a coating on fruit surfaces were obtained. One of the formulations was created by using a combination of native and pregelatinised potato starch; the other formulation was obtained using maltodextrin and by adding skimmed milk and sucrose as protectant compounds. The formulated products reduced the incidence and severity of B. cinerea, and CPA-1 survival rate was increased under stress conditions of temperature and humidity.

Slipstream pilot-scale demonstration of a novel amine-based post-combustion technology for carbon dioxide capture from coal-fired power plant flue gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishnamurthy, Krish R.

Post-combustion CO 2 capture (PCC) technology offers flexibility to treat the flue gas from both existing and new coal-fired power plants and can be applied to treat all or a portion of the flue gas. Solvent-based technologies are today the leading option for PCC from commercial coal-fired power plants as they have been applied in large-scale in other applications. Linde and BASF have been working together to develop and further improve a PCC process incorporating BASF’s novel aqueous amine-based solvent technology. This technology offers significant benefits compared to other solvent-based processes as it aims to reduce the regeneration energy requirementsmore » using novel solvents that are very stable under the coal-fired power plant feed gas conditions. BASF has developed the desired solvent based on the evaluation of a large number of candidates. In addition, long-term small pilot-scale testing of the BASF solvent has been performed on a lignite-fired flue gas. In coordination with BASF, Linde has evaluated a number of options for capital cost reduction in large engineered systems for solvent-based PCC technology. This report provides a summary of the work performed and results from a project supported by the US DOE (DE-FE0007453) for the pilot-scale demonstration of a Linde-BASF PCC technology using coal-fired power plant flue gas at a 1-1.5 MWe scale in Wilsonville, AL at the National Carbon Capture Center (NCCC). Following a project kick-off meeting in November 2011 and the conclusion of pilot plant design and engineering in February 2013, mechanical completion of the pilot plant was achieved in July 2014, and final commissioning activities were completed to enable start-up of operations in January 2015. Parametric tests were performed from January to December 2015 to determine optimal test conditions and evaluate process performance over a variety of operation parameters. A long-duration 1500-hour continuous test campaign was performed from May to August 2016 at a selected process condition to evaluate process performance and solvent stability over a longer period similar to how the process would operate as a continuously running large-scale PCC plant. The pilot plant integrated a number of unique features of the Linde-BASF technology aimed at lowering overall energy consumption and capital costs. During the overall test period including startup, parametric testing and long-duration testing, the pilot plant was operated for a total of 6,764 hours out of which testing with flue gas was performed for 4,109 hours. The pilot plant testing demonstrated all of the performance targets including CO 2 capture rate exceeding 90%, CO 2 purity exceeding 99.9 mol% (dry), flue gas processing capacity up to 15,500 lbs/hr (equivalent to 1.5 MWe capacity slipstream), regeneration energy as low as 2.7 GJ/tonne CO 2, and regenerator operating pressure up to 3.4 bara. Excellent solvent stability performance data was measured and verified by Linde and BASF during both test campaigns. In addition to process data, significant operational learnings were gained from pilot tests that will contribute greatly to the commercial success of PCC. Based on a thorough techno-economic assessment (TEA) of the Linde-BASF PCC process integrated with a 550 MWe supercritical coal-fired power plant, the net efficiency of the integrated power plant with CO 2 capture is increased from 28.4% with the DOE/NETL Case 12 reference to 30.9% with the Linde-BASF PCC plant previously presented utilizing the BASF OASE® blue solvent [Ref. 4], and is further increased to 31.4% using a Linde-BASF PCC plant with BASF OASE® blue solvent and an advanced stripper interstage heater (SIH) configuration. The Linde-BASF PCC plant incorporating the BASF OASE® blue solvent also results in significantly lower overall capital costs, thereby reducing the cost of electricity (COE) and cost of CO 2 captured from $147.25/MWh and $56.49/MT CO 2, respectively, for the reference DOE/NETL Case 12 plant, to $128.49/MWh and $41.85/MT CO2 for process case LB1, respectively, and $126.65/MWh and $40.66/MT CO 2 for process case SIH, respectively. With additional innovative Linde-BASF PCC process configuration improvements, the COE and cost of CO 2 captured can be further reduced to $125.51/MWh and $39.90/MT CO 2 for a further optimized PCC process defined as LB1-CREB. Most notably, the Linde-BASF process options assessed have already demonstrated the potential to lower the cost of CO 2 captured below the DOE target of $40/MT CO 2 at the 550 MWe scale for second generation PCC technologies. Project organization, structure, goals, tasks, accomplishments, process criteria and milestones will be presented in this report along with highlights and key results from parametric and long-duration testing of the Linde-BASF PCC pilot. The parametric and long-duration testing campaigns were aimed at validating the performance of the PCC technology against targets determined from a preliminary techno-economic assessment. The stability of the solvent with extended operation in a realistic power plant setting was measured with performance verified. Additionally, general solvent classification information, process operating conditions, normalized solvent performance data, solvent stability test results, flue gas conditions data, CO 2 purity data in the gaseous product stream, steam requirements and process flow diagrams, and updated process economic data for a scaled-up 550 MWe supercritical power plant with CO 2 capture are presented and discussed in this report.« less

The levels of processing effect under nitrogen narcosis.

PubMed

Kneller, Wendy; Hobbs, Malcolm

2013-01-01

Previous research has consistently demonstrated that inert gas (nitrogen) narcosis affects free recall but not recognition memory in the depth range of 30 to 50 meters of sea water (msw), possibly as a result of narcosis preventing processing when learned material is encoded. The aim of the current research was to test this hypothesis by applying a levels of processing approach to the measurement of free recall under narcosis. Experiment 1 investigated the effect of depth (0-2 msw vs. 37-39 msw) and level of processing (shallow vs. deep) on free recall memory performance in 67 divers. When age was included as a covariate, recall was significantly worse in deep water (i.e., under narcosis), compared to shallow water, and was significantly higher in the deep processing compared to shallow processing conditions in both depth conditions. Experiment 2 demonstrated that this effect was not simply due to the different underwater environments used for the depth conditions in Experiment 1. It was concluded memory performance can be altered by processing under narcosis and supports the contention that narcosis affects the encoding stage of memory as opposed to self-guided search (retrieval).

Neuro-parity pattern recognition system and method

DOEpatents

Gross, Kenneth C.; Singer, Ralph M.; Van Alstine, Rollin G.; Wegerich, Stephan W.; Yue, Yong

2000-01-01

A method and system for monitoring a process and determining its condition. Initial data is sensed, a first set of virtual data is produced by applying a system state analyzation to the initial data, a second set of virtual data is produced by applying a neural network analyzation to the initial data and a parity space analyzation is applied to the first and second set of virtual data and also to the initial data to provide a parity space decision about the condition of the process. A logic test can further be applied to produce a further system decision about the state of the process.

The interaction of affective with psychotic processes: A test of the effects of worrying on working memory, jumping to conclusions, and anomalies of experience in patients with persecutory delusions

PubMed Central

Freeman, Daniel; Startup, Helen; Dunn, Graham; Černis, Emma; Wingham, Gail; Pugh, Katherine; Cordwell, Jacinta; Kingdon, David

2013-01-01

Worry has traditionally been considered in the study of common emotional disorders such as anxiety and depression, but recent studies indicate that worry may be a causal factor in the occurrence and persistence of persecutory delusions. The effect of worry on processes traditionally associated with psychosis has not been tested. The aim of the study was to examine the short-term effects of a bout of worry on three cognitive processes typically considered markers of psychosis: working memory, jumping to conclusions, and anomalous internal experience. Sixty-seven patients with persecutory delusions in the context of a non-affective psychotic disorder were randomised to a worry induction, a worry reduction, or a neutral control condition. They completed tests of the cognitive processes before and after the randomisation condition. The worry induction procedure led to a significant increase in worry. The induction of worry did not affect working memory or jumping to conclusions, but it did increase a range of mild anomalous experiences including feelings of unreality, perceptual alterations, and temporal disintegration. Worry did not affect the occurrence of hallucinations. The study shows that a period of worry causes a range of subtle odd perceptual disturbances that are known to increase the likelihood of delusions. It demonstrates an interaction between affective and psychotic processes in patients with delusions. PMID:23871449

Biodegradation screening of chemicals in an artificial matrix simulating the water-sediment interface.

PubMed

Baginska, Ewelina; Haiß, Annette; Kümmerer, Klaus

2015-01-01

Biodegradation is the most important attenuation process for most of organic chemicals in the environment. This process decides whether the organic substance itself or its degradation products rests in the environment and should be considered for a further risk assessment. This work presents the development of a water sediment screening test, based on OECD guideline 308, with a high significance to environmental conditions and with a good reproducibility and consistency of results. The increased reproducibility was achieved by creating an artificial and standardized medium, based on the existing OECD guidelines OECD 302C, 301D and 218. Each test consisted of five different series: blank, quality control, test, toxicity control and abiotic control. Biodegradation was assessed by measurement of pressure difference in closed vessels using the OxiTop(®) system. Aniline, diethylene glycol and sodium acetate were used to optimize and validate test conditions. Additionally, two pharmaceuticals: Acetaminophen and ciprofloxacin (CIP) were tested as an example of possible test application. Acetaminophen was mainly removed from the system by biodegradation whereas CIP was removed from water phase by sorption onto sediment. Water sediment test proved to be a promising tool for the biodegradation investigation of chemicals in the water-sediment interface. Copyright © 2014 Elsevier Ltd. All rights reserved.

Forecasting volatility with neural regression: a contribution to model adequacy.

PubMed

Refenes, A N; Holt, W T

2001-01-01

Neural nets' usefulness for forecasting is limited by problems of overfitting and the lack of rigorous procedures for model identification, selection and adequacy testing. This paper describes a methodology for neural model misspecification testing. We introduce a generalization of the Durbin-Watson statistic for neural regression and discuss the general issues of misspecification testing using residual analysis. We derive a generalized influence matrix for neural estimators which enables us to evaluate the distribution of the statistic. We deploy Monte Carlo simulation to compare the power of the test for neural and linear regressors. While residual testing is not a sufficient condition for model adequacy, it is nevertheless a necessary condition to demonstrate that the model is a good approximation to the data generating process, particularly as neural-network estimation procedures are susceptible to partial convergence. The work is also an important step toward developing rigorous procedures for neural model identification, selection and adequacy testing which have started to appear in the literature. We demonstrate its applicability in the nontrivial problem of forecasting implied volatility innovations using high-frequency stock index options. Each step of the model building process is validated using statistical tests to verify variable significance and model adequacy with the results confirming the presence of nonlinear relationships in implied volatility innovations.

Mediodorsal nucleus of the thalamus is critical for the expression of memory of methamphetamine-produced conditioned place preference in rats.

PubMed

Kuo, C-S; Chai, S-C; Chen, H-H

2011-03-31

Methamphetamine (MA) is a powerful and highly addictive psychostimulant. However, the neural substrate mediating MA-induced conditioned effects, an essential part of addiction, remain unclear. The present study investigated the involvement of the anterior cingulate cortex (ACC), the lateral nucleus of amygdala (LNA), and the mediodorsal nucleus of the thalamus (MD) in MA-conditioned place preference (CPP). Rats underwent bilateral radio-frequency lesions of the ACC, LNA, or MD followed by MA CPP training. Lesions of the MD, but not the ACC or LNA, disrupted MA CPP learning. To clarify the role of the MD on the different stages of the MA CPP memory process, bilateral microinfusions of lidocaine into the MD were performed 5 min prior to each conditioning trial, immediately after the conditioning trial, or 5 min before the testing phase. Pretesting, but not pre- or post-conditioning, infusions of lidocaine into the MD impaired MA CPP. Furthermore, a clear preference for the previously conditioned MA paired cues was expressed when the rats were tested again 24 h after infusions of lidocaine. These results are interpreted as indicating that the MD is specifically involved in the memory retrieval process of MA associated memory which suggests the MD could have an important role in relapse in individuals suffering from MA addiction. Copyright © 2011 IBRO. Published by Elsevier Ltd. All rights reserved.

Electrochemical CO2 and O2 separation for crew and plant environments

NASA Technical Reports Server (NTRS)

Lee, M. G.; Grigger, David J.; Foerg, Sandra L.

1992-01-01

The study describes a closed ecosystem concept that includes electrochemical CO2 and O2 separators and a moisture condenser/separator for maintaining CO2, O2, and humidity levels in the crew and plant habitats at their respective optimal conditions. The key processes of this concept are aqueous electrolyte-based electrochemical CO2 and O2 separations. The principles and cell characteristics of these electrochemical gas separation processes are described. Also presented are descriptions of test hardware and the test results of the Electrochemical CO2 Separator (ECS) and the Electrochemical O2 Separator (EOS), and the combination of the ECS and the EOS. The test results proved that the ECS and EOS processes for the combined concept are viable.

Industrial Test of High Strength Steel Plates Free Boron Q890D Used for Engineering Machinery

NASA Astrophysics Data System (ADS)

Dong, Ruifeng; Liu, Zetian; Gao, Jun

The chemistry composition, process parameters and the test results of Q890D free boron high strength steel plate used for engineering machinery was studied. The 16 40 mm thickness steel plates with good mechanical properties that was yield strength of 930 970 MPa, tensile strength of 978 1017 MPa, elongation of 13.5 15%, the average impact energy value of more than 100 J were developed by improving steel purity, adopting the reasonable controlled rolling and cooling process, using reasonable off-line quenching and tempering process. The test plates have good crack resistance in 60 °C preheat temperature condition because of that there are no any cracks in the surfaces, cross-section and roots of welding joints.

Flocculation increases the efficacy of depth filtration during the downstream processing of recombinant pharmaceutical proteins produced in tobacco.

PubMed

Buyel, Johannes F; Fischer, Rainer

2014-02-01

Flocculation is a cost-effective method that is used to improve the efficiency of clarification by causing dispersed particles to clump together, allowing their removal by sedimentation, centrifugation or filtration. The efficacy of flocculation for any given process depends on the nature and concentration of the particulates in the feed stream, the concentration, charge density and length of the flocculant polymer, the shear rate, the properties of the feed stream (e.g. pH and ionic strength) and the properties of the target products. We tested a range of flocculants and process conditions using a design of experiments approach to identify the most suitable polymers for the clarification step during the production of a HIV-neutralizing monoclonal antibody (2G12) and a fluorescent marker protein (DsRed) expressed in transgenic tobacco leaves. Among the 23 different flocculants we tested, the greatest reduction in turbidity was achieved with Polymin P, a branched, cationic polyethylenimine with a charge density of 13.0 meq/g. This flocculant reduced turbidity by more than 90% under a wide range of process conditions. We developed a model that predicted its performance under different process conditions, and this enabled us to increase the depth filter capacity three-sevenfold depending on the process scale, depth filter type and plant species. The costs of filter consumables were reduced by more than 50% compared with a process without flocculant, and there was no loss of recovery for either 2G12 or DsRed. © 2013 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

The need to improve health care in prisons

PubMed Central

Fernandes, Luiz Henrique; Alvarenga, Carlos Willie; dos Santos, Luciane Loures; Pazin, Antonio

2014-01-01

OBJECTIVE To analyze physical structure, working conditions of health professionals and outline of the procedures established in prisons. METHODS We analyzed 34 provisional detention centers and 69 male and six female prison units in the state of Sao Paulo, Southeastern Brazil, in 2009. A self-applied instrument was developed to collect quantitative data on the characteristics of health care structure, equipment and personnel in prisons. Analysis of variance (ANOVA) or equivalent non-parametric tests and Chi-square or Fisher’s tests were used to compare categorical and continuous variables, respectively, between the groups. RESULTS The main problems were delays in the results of laboratory tests and imaging. With respect to the teams, it was observed that a large majority were in conditions close to those proposed by the Bipartite Commission 2013 but without improvement being reflected in the indicators. With respect to the process, more than 60.0% of prisons located in small towns do not have the structural conditions to ensure secondary or tertiary health care for the continuity of treatment. CONCLUSIONS This profile of prisons in the country can be used for planning and monitoring future actions for the continuous improvement of healthcare processes. PMID:24897049

Stepped-frequency GPR for utility line detection using polarization-dependent scattering

NASA Astrophysics Data System (ADS)

Jensen, Ole K.; Gregersen, Ole G.

2000-04-01

A GPR for detection of buried cables and pipes is developed by Ekko Dane Production in cooperation with Aalborg University. The appearance is a 'lawn mower' model including antennas, electronics and on-line data processing. A successful result is obtained by combining dedicated hardware and signal processing. The inherent signal to clutter ratio is bad, but making measurements at many polarization angles and subsequent signal processing improves the ratio. A simple model of the polarization dependence of the scattering from the target is used. The method is improved by combining the polarization filtering with averaging over small horizontal displacements. A stepped frequency measurement system is used. The method often implies long measurement times, but this problem is overcome by development of fast RF-electronics. Standard signal processors are used for real-time data processing. Several antenna array configurations are tested and optimized for low coupling between transmitter and receiver and for a short impulse response. A large number of tests have been made for different targets, e.g. metal cables and plastic pipes filled with air or water. Tests have been made under realistic ground conditions, including sand, wet clay, pavements and grass covered soil. The results show reliable detection even when the conditions are difficult.

Cognitive bias in back pain patients attending osteopathy: testing the enmeshment model in reference to future thinking.

PubMed

Read, Jessica; Pincus, Tamar

2004-12-01

Depressive symptoms are common in chronic pain. Previous research has found differences in information-processing biases in depressed pain patients and depressed people without pain. The schema enmeshment model of pain (SEMP) has been proposed to explain chronic pain patients' information-processing biases. Negative future thinking is common in depression but has not been explored in relation to chronic pain and information-processing models. The study aimed to test the SEMP with reference to future thinking. An information-processing paradigm compared endorsement and recall bias between depressed and non-depressed chronic low back pain patients and control participants. Twenty-five depressed and 35 non-depressed chronic low back pain patients and 25 control participants (student osteopaths) were recruited from an osteopathy practice. Participants were asked to endorse positive and negative ill-health, depression-related, and neutral (control) adjectives, encoded in reference to either current or future time-frame. Incidental recall of the adjectives was then tested. While the expected hypothesis of a recall bias by depressed pain patients towards ill-health stimuli in the current condition was confirmed, the recall bias was not present in the future condition. Additionally, patterns of endorsement and recall bias differed. Results extend understanding of future thinking in chronic pain within the context of the SEMP.

Boeing's CST-100 Structural Test Article Shipment from C3PF to B

NASA Image and Video Library

2016-11-22

Boeing’s Structural Test Article of its CST-100 Starliner spacecraft is moved out of the company’s Commercial Crew and Cargo Processing Facility at NASA’s Kennedy Space Center on its way to Huntington Beach, California, for evaluations. Built to the specifications of an operational spacecraft, the STA is intended to be evaluated through a series of thorough testing conditions.

78 FR 14060 - Migratory Bird Hunting; Revision of Language for Approval of Nontoxic Shot for Use in Waterfowl...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-04

... process, send the Tier 2 testing results and analyses to us. You must ensure that copies of all the raw..., you may conduct the Tier 3 testing. You must ensure that copies of the raw data and the statistical... deficient diet. Conduct a chronic exposure test under adverse conditions that complies with the following...

Debates—Hypothesis testing in hydrology: Introduction

NASA Astrophysics Data System (ADS)

Blöschl, Günter

2017-03-01

This paper introduces the papers in the "Debates—Hypothesis testing in hydrology" series. The four articles in the series discuss whether and how the process of testing hypotheses leads to progress in hydrology. Repeated experiments with controlled boundary conditions are rarely feasible in hydrology. Research is therefore not easily aligned with the classical scientific method of testing hypotheses. Hypotheses in hydrology are often enshrined in computer models which are tested against observed data. Testability may be limited due to model complexity and data uncertainty. All four articles suggest that hypothesis testing has contributed to progress in hydrology and is needed in the future. However, the procedure is usually not as systematic as the philosophy of science suggests. A greater emphasis on a creative reasoning process on the basis of clues and explorative analyses is therefore needed.

The effect of processing conditions on the stability of fructooligosaccharides in acidic food products.

PubMed

Vega, Roberto; Zuniga-Hansen, M E

2015-04-15

The effect of processing conditions (temperature and degree of polymerisation, DP) on the stability of short-chain fructooligosaccharides (sc-FOS) was investigated in three reaction media (sodium citrate buffer and orange and tomato juices) in a kinetic study at pH 3.5. In addition, kinetic equations as a function of temperature and pH were developed, using published data. Pentasaccharides were more stable to heat treatment than were trisaccharides under all of the conditions tested. In addition, the sc-FOS were more stable in orange juice, followed by tomato juice and citrate buffer. The results showed that, in addition to temperature and pH, the DP and food matrix, including the type of pasteurisation, must be considered when processing foods enriched with sc-FOS. Furthermore, the continuous thermal processing simulation for each of the equivalent processes at 90 °C revealed that the percent retention of sc-FOS is greater than 95% at temperatures above 95 °C. Copyright © 2014 Elsevier Ltd. All rights reserved.

Picturing survival memories: enhanced memory after fitness-relevant processing occurs for verbal and visual stimuli.

PubMed

Otgaar, Henry; Smeets, Tom; van Bergen, Saskia

2010-01-01

Recent studies have shown that processing words according to a survival scenario leads to superior retention relative to control conditions. Here, we examined whether a survival recall advantage could be elicited by using pictures. Furthermore, in Experiment 1, we were interested in whether survival processing also results in improved memory for details. Undergraduates rated the relevance of pictures in a survival, moving, or pleasantness scenario and were subsequently given a surprise free recall test. We found that survival processing yielded superior retention. We also found that distortions occurred more often in the survival condition than in the pleasantness condition. In Experiment 2, we directly compared the survival recall effect between pictures and words. A comparable survival recall advantage was found for pictures and words. The present findings support the idea that memory is enhanced by processing information in terms of fitness value, yet at the same time, the present results suggest that this may increase the risk for memory distortions.

Study on thermal effects & sulfurized additives, in lubricating greases

NASA Astrophysics Data System (ADS)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to understand the effects of the addition of sulphur from a sulfurized olefin to MoS2 through mechanical processing has been conducted. This mechanically processed additive mixed is tested through regular ASTM D2266 test. The hypothesis was to make more shear able MoS 2 layers available by using the sulphur from the olefin to form the basic FeS layer that reduces the continuous wear rate. The results have been studied using SEM and EDX imaging.

Study of oxygen gas production phenomenon during stand and discharge in silver-zinc batteries

NASA Technical Reports Server (NTRS)

1973-01-01

The effects of a number of cell process and performance variables upon the oxygen evolution rate of silver/silver oxide cathodes are studied to predict and measure the conditions which would result in the production of a minimum of oxygen. The following five tasks comprise the study: the design and fabrication of two pilot test cells to be used for electrode testing; the determination of the sensitivity and accuracy of the test cell; the determination of total volumes and rates of generation by cathodes of standard production procedures; the construction of a sequential test plan; and the construction of a series of positive formation cells in which formation process factors can be controlled.

Focus adjustment method for CBERS 3 and 4 satellites Mux camera to be performed in air condition and its experimental verification for best performance in orbital vacuum condition

NASA Astrophysics Data System (ADS)

Scaduto, Lucimara C. N.; Malavolta, Alexandre T.; Modugno, Rodrigo G.; Vales, Luiz F.; Carvalho, Erica G.; Evangelista, Sérgio; Stefani, Mario A.; de Castro Neto, Jarbas C.

2017-11-01

The first Brazilian remote sensing multispectral camera (MUX) is currently under development at Opto Eletronica S.A. It consists of a four-spectral-band sensor covering a 450nm to 890nm wavelength range. This camera will provide images within a 20m ground resolution at nadir. The MUX camera is part of the payload of the upcoming Sino-Brazilian satellites CBERS 3&4 (China-Brazil Earth Resource Satellite). The preliminary alignment between the optical system and the CCD sensor, which is located at the focal plane assembly, was obtained in air condition, clean room environment. A collimator was used for the performance evaluation of the camera. The preliminary performance evaluation of the optical channel was registered by compensating the collimator focus position due to changes in the test environment, as an air-to-vacuum environment transition leads to a defocus process in this camera. Therefore, it is necessary to confirm that the alignment of the camera must always be attained ensuring that its best performance is reached for an orbital vacuum condition. For this reason and as a further step on the development process, the MUX camera Qualification Model was tested and evaluated inside a thermo-vacuum chamber and submitted to an as-orbit vacuum environment. In this study, the influence of temperature fields was neglected. This paper reports on the performance evaluation and discusses the results for this camera when operating within those mentioned test conditions. The overall optical tests and results show that the "in air" adjustment method was suitable to be performed, as a critical activity, to guarantee the equipment according to its design requirements.

A Role of DLPFC in the Learning Process of Human Mate Copying

PubMed Central

Zhuang, Jin-Ying; Xie, Jiajia; Hu, Die; Fan, Mingxia; Zheng, Li

2016-01-01

In the current study, we conducted a behavioral experiment to test the mate coping effect and a functional magnetic resonance imaging (fMRI) experiment to test the neural basis involved in the social learning process of mate copying. In the behavioral experiment, participants were asked to rate the attractiveness of isolated opposite-sex (potential mates) facial photographs, then shown the targets associating with a neutral-faced model with textual cues indicating the models’ attitude (interested vs. not-interested) toward the potential mates, and then asked to re-evaluate the potential mates’ attractiveness. Using a similar procedure as the behavioral experiment, participants were scanned while observing the compound images in the fMRI experiment. The mate copying effect was confirmed in the behavioral experiment –greater increase in attractiveness ratings was observed for opposite-sex photographs in the interested than in the not-interested condition. The fMRI results showed that the dorsolateral prefrontal gyrus (DLPFC) was significantly active in the comparison of interested > not-interested condition, suggesting that a cognitive integration and selection function may be involved when participants process information from conditions related to mate copying. PMID:27148151

Diagnostic approach for monitoring hydroclimatic conditions related to emergence of west nile virus in west virginia.

PubMed

Jutla, Antarpreet; Huq, Anwar; Colwell, Rita R

2015-01-01

West Nile virus (WNV), mosquito-borne and water-based disease, is increasingly a global threat to public health. Since its appearance in the northeastern United States in 1999, WNV has since been reported in several states in the continental United States. The objective of this study is to highlight role of hydroclimatic processes estimated through satellite sensors in capturing conditions for emergence of the vectors in historically disease free regions. We tested the hypothesis that an increase in surface temperature, in combination with intensification of vegetation, and enhanced precipitation, lead to conditions favorable for vector (mosquito) growth. Analysis of land surface temperature (LST) pattern shows that temperature values >16°C, with heavy precipitation, may lead to abundance of the mosquito population. This hypothesis was tested in West Virginia where a sudden epidemic of WNV infection was reported in 2012. Our results emphasize the value of hydroclimatic processes estimated by satellite remote sensing, as well as continued environmental surveillance of mosquitoes, because when a vector-borne infection like WNV is discovered in contiguous regions, the risk of spread of WNV mosquitoes increase at points where appropriate hydroclimatic processes intersect with the vector niche.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, A.; Devenny, D.; Porcari, G.

The activities carried out and the results obtained from a 15 tons/hour oil sands extraction pilot plant operated in Fort McMurray in Northern Alberta are described. The process is the Rio Tinto TIL Holding S.A. (RTR)/Gulf Canada Lt. Oil Sands Extraction Process. It is a modified hot water extraction process. It is used to extract bitumen from Athabasca oil sands. The test ran from July to December 1981 through ambient conditions ranging from plus 38/sup 0/C to minus 30/sup 0/C (100/sup 0/F to -22/sup 0/F). The process, the on-site facilities, the test program, an analysis of plant performance, an appraisalmore » of the process economics, and an evaluation of its potential application are described.« less

Validation of Helicopter Gear Condition Indicators Using Seeded Fault Tests

NASA Technical Reports Server (NTRS)

Dempsey, Paula; Brandon, E. Bruce

2013-01-01

A "seeded fault test" in support of a rotorcraft condition based maintenance program (CBM), is an experiment in which a component is tested with a known fault while health monitoring data is collected. These tests are performed at operating conditions comparable to operating conditions the component would be exposed to while installed on the aircraft. Performance of seeded fault tests is one method used to provide evidence that a Health Usage Monitoring System (HUMS) can replace current maintenance practices required for aircraft airworthiness. Actual in-service experience of the HUMS detecting a component fault is another validation method. This paper will discuss a hybrid validation approach that combines in service-data with seeded fault tests. For this approach, existing in-service HUMS flight data from a naturally occurring component fault will be used to define a component seeded fault test. An example, using spiral bevel gears as the targeted component, will be presented. Since the U.S. Army has begun to develop standards for using seeded fault tests for HUMS validation, the hybrid approach will be mapped to the steps defined within their Aeronautical Design Standard Handbook for CBM. This paper will step through their defined processes, and identify additional steps that may be required when using component test rig fault tests to demonstrate helicopter CI performance. The discussion within this paper will provide the reader with a better appreciation for the challenges faced when defining a seeded fault test for HUMS validation.

Effects of angle of model-demonstration on learning of motor skill.

PubMed

Ishikura, T; Inomata, K

1995-04-01

The purpose was to examine the effects of three different demonstrations by a model on acquisition and retention of a sequential gross movement task. The second purpose was to examine the relationship between reversal processing of visual information about skills and coding of skill information. Thirty undergraduates (15 men and 15 women) were assigned into one of three conditions, Objective condition which demonstrated the task with the model facing the subject. Looking-glass condition in which the skill was demonstrated with the model facing the subject who viewed the performance opposite the right and left directions in executing the task, and the Subjective condition in which the subject observed the model from the rear. Number of immediate recall tests required to accomplish the sequential movements completely and the sum of the performance points for reproduced movements at each delayed recall test (1 day, 7 days, and 5 mo. after the immediate recall test) were employed. Analysis indicated the Subjective condition produced a significantly greater modeling effect in immediate recall of the movements than the Looking-glass condition. Retention of the acquired skills was almost equal under the three conditions.

76 FR 31453 - Special Conditions: Gulfstream Model GVI Airplane; Single-Occupant Side-Facing Seats

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-01

.... SID TTI data must be processed as defined in Federal Motor Vehicle Safety Standard (FMVSS) part 571...). Pass/fail injury assessments: TTI and pelvic acceleration. 2. One longitudinal test with the Hybrid II... pelvic acceleration. 3. Vertical (14g) test with modified Hybrid II ATDs using existing pass/fail...

The Introduction of Standardized External Testing in Ukraine: Challenges and Successes

ERIC Educational Resources Information Center

Kovalchuk, Serhiy; Koroliuk, Svitlana

2012-01-01

Standardized external testing (SET) began to be implemented in Ukraine in 2008 as an instrument for combating corruption in higher education and ensuring fair university admission. This article examines the conditions and processes that led to the introduction of SET, overviews its implementation over three years (2008-10), analyzes SET and…

Preparation of Pd-Loaded Hierarchical FAU Membranes and Testing in Acetophenone Hydrogenation.

PubMed

Molinari, Raffaele; Lavorato, Cristina; Mastropietro, Teresa F; Argurio, Pietro; Drioli, Enrico; Poerio, Teresa

2016-03-22

Pd-loaded hierarchical FAU (Pd-FAU) membranes, containing an intrinsic secondary non-zeolitic (meso)porosity, were prepared and tested in the catalytic transfer hydrogenation of acetophenone (AP) to produce phenylethanol (PE), an industrially relevant product. The best operating conditions were preliminarily identified by testing different solvents and organic hydrogen donors in a batch hydrogenation process where micron-sized FAU seeds were employed as catalyst support. Water as solvent and formic acid as hydrogen source resulted to be the best choice in terms of conversion for the catalytic hydrogenation of AP, providing the basis for the design of a green and sustainable process. The best experimental conditions were selected and applied to the Pd-loaded FAU membrane finding enhanced catalytic performance such as a five-fold higher productivity than with the unsupported Pd-FAU crystals (11.0 vs. 2.2 mgproduct gcat(-1)·h(-1)). The catalytic performance of the membrane on the alumina support was also tested in a tangential flow system obtaining a productivity higher than that of the batch system (22.0 vs. 11.0 mgproduct gcat(-1)·h(-1)).

Automatic control of NASA Langley's 0.3-meter cryogenic test facility

NASA Technical Reports Server (NTRS)

Thibodeaux, J. J.; Balakrishna, S.

1980-01-01

Experience during the past 6 years of operation of the 0.3-meter transonic cryogenic tunnel at the NASA Langley Research Center has shown that there are problems associated with efficient operation and control of cryogenic tunnels using manual control schemes. This is due to the high degree of process crosscoupling between the independent control variables (temperature, pressure, and fan drive speed) and the desired test condition (Mach number and Reynolds number). One problem has been the inability to maintain long-term accurate control of the test parameters. Additionally, the time required to change from one test condition to another has proven to be excessively long and much less efficient than desirable in terms of liquid nitrogen and electrical power usage. For these reasons, studies have been undertaken to: (1) develop and validate a mathematical model of the 0.3-meter cryogenic tunnel process, (2) utilize this model in a hybrid computer simulation to design temperature and pressure feedback control laws, and (3) evaluate the adequacy of these control schemes by analysis of closed-loop experimental data. This paper will present the results of these studies.

Microstructural examination of

NASA Astrophysics Data System (ADS)

Fukuoka, C.; Yoshizawa, H.; Nakagawa, Y. G.; Lapides, M. E.

1993-10-01

Fatigue tests were performed to examine how microstructural conditioning influences crack initiation and propagation in SA508 class 3 low-carbon steel. A 3-mm-long crack was introduced in compact tension (CT) fatigue test specimens under four different loads in order to obtain crack tip plastic zones at different stress intensity factor ranges, ΔK = 18, 36, 54, and 72 MPa√m. The microstructure of the plastic zones around the crack tip were examined by trans- mission electron microscopy (TEM) and selected area electron diffraction (SAD). Micro- orientation of the dislocation cells in the plastic zones of all of the CT samples increased to 4 deg from the level of an as-received sample. Four-point bending fatigue tests were performed for plate shape samples with a large cyclic strain range. The SAD value of the bending samples was also 4 deg in the damaged area where cracks already initiated at an early stage of the fatigue process. These test results indicate that the microstructural conditioning is a prerequisite for the fatigue crack initiation and propagation in SA508. These observations may lead to better under- standing of how fatigue initiation processes transit to cracks.

Cool colors: color-induced nasal thermal sensations.

PubMed

Michael, George A; Rolhion, Pauline

2008-05-09

We asked subjects to sniff a bottle containing distilled water and to say whether they felt a cooling or warming sensation in the nasal cavity. Odorless food coloring was added to three of these bottles so as to obtain one yellow, one green, one red and one colorless solution. Subjects were presented with each bottle four times under free viewing conditions or while blindfolded, and each nostril was tested separately. Although no thermal stimulus was present, subjects reported thermal sensations, but only under free viewing conditions. The nature of these sensations depended on the color of the solution, with green inducing cooling and red warming sensations. It also depended on which nostril was tested, with warming sensations evidenced only when the left nostril was tested, and cooling sensations only when the right nostril was tested. It is the first time color has been reported to induce nasal thermal sensations in the absence of thermal stimuli. These results are therefore entirely new. Furthermore, they suggest that thermosensory processing and judgment may depend on lateralized processes in the human brain.

Leaching of biocides used in façade coatings under laboratory test conditions.

PubMed

Schoknecht, Ute; Gruycheva, Jana; Mathies, Helena; Bergmann, Hannelore; Burkhardt, Michael

2009-12-15

The European Biocidal Products Directive 98/8/EC requires a risk assessment concerning possible effects of active ingredients on the environment. Biocides can be leached from treated materials exposed to outdoor use. These emissions have to be estimated and evaluated during the authorization procedure. Different immersion and irrigation tests were performed to investigate leaching of biocides from façade coatings. Several marketed formulations of textured coatings and paints spiked with a mixture of commonly used active ingredients (OIT, DCOIT, IPBC, carbendazim, isoproturon, diuron, terbutryn, and Irgarol 1051) were investigated. The emission process can be described by time-dependent functions that depend on the test conditions. The results of all test procedures confirm that leachability is related to water solubility and n-octanol-water partition coefficient of the active ingredients and that leaching of biocides from façade coatings is mainly a diffusion controlled process. Other factors like the composition of the product, availability and transport of water, concentration of active ingredients in the coatings, as well as UV-exposure of the coatings influence biocide emissions.

Delta, theta, beta, and gamma brain oscillations index levels of auditory sentence processing.

PubMed

Mai, Guangting; Minett, James W; Wang, William S-Y

2016-06-01

A growing number of studies indicate that multiple ranges of brain oscillations, especially the delta (δ, <4Hz), theta (θ, 4-8Hz), beta (β, 13-30Hz), and gamma (γ, 30-50Hz) bands, are engaged in speech and language processing. It is not clear, however, how these oscillations relate to functional processing at different linguistic hierarchical levels. Using scalp electroencephalography (EEG), the current study tested the hypothesis that phonological and the higher-level linguistic (semantic/syntactic) organizations during auditory sentence processing are indexed by distinct EEG signatures derived from the δ, θ, β, and γ oscillations. We analyzed specific EEG signatures while subjects listened to Mandarin speech stimuli in three different conditions in order to dissociate phonological and semantic/syntactic processing: (1) sentences comprising valid disyllabic words assembled in a valid syntactic structure (real-word condition); (2) utterances with morphologically valid syllables, but not constituting valid disyllabic words (pseudo-word condition); and (3) backward versions of the real-word and pseudo-word conditions. We tested four signatures: band power, EEG-acoustic entrainment (EAE), cross-frequency coupling (CFC), and inter-electrode renormalized partial directed coherence (rPDC). The results show significant effects of band power and EAE of δ and θ oscillations for phonological, rather than semantic/syntactic processing, indicating the importance of tracking δ- and θ-rate phonetic patterns during phonological analysis. We also found significant β-related effects, suggesting tracking of EEG to the acoustic stimulus (high-β EAE), memory processing (θ-low-β CFC), and auditory-motor interactions (20-Hz rPDC) during phonological analysis. For semantic/syntactic processing, we obtained a significant effect of γ power, suggesting lexical memory retrieval or processing grammatical word categories. Based on these findings, we confirm that scalp EEG signatures relevant to δ, θ, β, and γ oscillations can index phonological and semantic/syntactic organizations separately in auditory sentence processing, compatible with the view that phonological and higher-level linguistic processing engage distinct neural networks. Copyright © 2016 Elsevier Inc. All rights reserved.

Research on filling process of fuel and oxidant during detonation based on absorption spectrum technology

NASA Astrophysics Data System (ADS)

Lv, Xiao-Jing; Li, Ning; Weng, Chun-Sheng

2014-12-01

Research on detonation process is of great significance for the control optimization of pulse detonation engine. Based on absorption spectrum technology, the filling process of fresh fuel and oxidant during detonation is researched. As one of the most important products, H2O is selected as the target of detonation diagnosis. Fiber distributed detonation test system is designed to enable the detonation diagnosis under adverse conditions in detonation process. The test system is verified to be reliable. Laser signals at different working frequency (5Hz, 10Hz and 20Hz) are detected. Change of relative laser intensity in one detonation circle is analyzed. The duration of filling process is inferred from the change of laser intensity, which is about 100~110ms. The peak of absorption spectrum is used to present the concentration of H2O during the filling process of fresh fuel and oxidant. Absorption spectrum is calculated, and the change of absorption peak is analyzed. Duration of filling process calculated with absorption peak consisted with the result inferred from the change of relative laser intensity. The pulse detonation engine worked normally and obtained the maximum thrust at 10Hz under experiment conditions. The results are verified through H2O gas concentration monitoring during detonation.

The combining of multiple hemispheric resources in learning-disabled and skilled readers' recall of words: a test of three information-processing models.

PubMed

Swanson, H L

1987-01-01

Three theoretical models (additive, independence, maximum rule) that characterize and predict the influence of independent hemispheric resources on learning-disabled and skilled readers' simultaneous processing were tested. Predictions related to word recall performance during simultaneous encoding conditions (dichotic listening task) were made from unilateral (dichotic listening task) presentations. The maximum rule model best characterized both ability groups in that simultaneous encoding produced no better recall than unilateral presentations. While the results support the hypothesis that both ability groups use similar processes in the combining of hemispheric resources (i.e., weak/dominant processing), ability group differences do occur in the coordination of such resources.

Evaluation of constant-Weber-number scaling for icing tests

NASA Technical Reports Server (NTRS)

Anderson, David N.

1996-01-01

Previous studies showed that for conditions simulating an aircraft encountering super-cooled water droplets the droplets may splash before freezing. Other surface effects dependent on the water surface tension may also influence the ice accretion process. Consequently, the Weber number appears to be important in accurately scaling ice accretion. A scaling method which uses a constant-Weber-number approach has been described previously; this study provides an evaluation of this scaling method. Tests are reported on cylinders of 2.5 to 15-cm diameter and NACA 0012 airfoils with chords of 18 to 53 cm in the NASA Lewis Icing Research Tunnel (IRT). The larger models were used to establish reference ice shapes, the scaling method was applied to determine appropriate scaled test conditions using the smaller models, and the ice shapes were compared. Icing conditions included warm glaze, horn glaze and mixed. The smallest size scaling attempted was 1/3, and scale and reference ice shapes for both cylinders and airfoils indicated that the constant-Weber-number scaling method was effective for the conditions tested.

Naloxone effects on extinction of ethanol- and cocaine-induced conditioned place preference in mice.

PubMed

Font, Laura; Houck, Christa A; Cunningham, Christopher L

2017-09-01

Previous studies found that naloxone (NLX) facilitated choice extinction of ethanol conditioned place preference (CPP) using long (60 min) test sessions, but there is little information on the variables determining this effect. These studies examined repeated exposure to NLX during extinction of ethanol- or cocaine-induced CPP using both short and long tests. DBA/2J mice were injected with NLX (0 or 10 mg/kg) before three 10- or 60-min choice extinction tests (experiment 1). All mice received a final 60-min test without NLX. Post-test NLX was given in experiment 2. Experiment 3 tested whether NLX would affect a forced extinction procedure. Experiment 4 tested its effect on extinction of cocaine-induced CPP. Pre-test (but not post-test) injections of NLX-facilitated choice extinction of ethanol CPP at both test durations. Pre-test NLX also facilitated forced extinction. However, pre-test NLX had no effect on choice extinction of cocaine CPP. Extinction test duration is not critical for engaging the opioid system during ethanol CPP extinction (experiment 1). Moreover, NLX's effect does not depend on CPP expression during extinction, just exposure to previously conditioned cues (experiment 3). The null effect of post-test NLX eliminates a memory consolidation interpretation (experiment 2) and the failure to alter cocaine CPP extinction argues against alteration of general learning or memory processes (experiment 4). Overall, these data suggest that the endogenous opioid system mediates a conditioned motivational effect that normally maintains alcohol-induced seeking behavior, which may underlie the efficacy of opiate antagonists in the treatment of alcoholism.

Method and apparatus for measuring coupled flow, transport, and reaction processes under liquid unsaturated flow conditions

DOEpatents

McGrail, Bernard P.; Martin, Paul F.; Lindenmeier, Clark W.

1999-01-01

The present invention is a method and apparatus for measuring coupled flow, transport and reaction processes under liquid unsaturated flow conditions. The method and apparatus of the present invention permit distinguishing individual precipitation events and their effect on dissolution behavior isolated to the specific event. The present invention is especially useful for dynamically measuring hydraulic parameters when a chemical reaction occurs between a particulate material and either liquid or gas (e.g. air) or both, causing precipitation that changes the pore structure of the test material.

Two-dimensional flow-through microcosms - Versatile test systems to study biodegradation processes in porous aquifers

NASA Astrophysics Data System (ADS)

Bauer, Robert D.; Rolle, Massimo; Kürzinger, Petra; Grathwohl, Peter; Meckenstock, Rainer U.; Griebler, Christian

2009-05-01

SummaryA fundamental prerequisite of any remedial activity is a sound knowledge of both the biotic and abiotic processes involved in transport and degradation of contaminants. Investigations of these aspects in situ often seem infeasible due to the complexity of interacting processes. A simplified portrayal of nature can be facilitated in laboratory-based two-dimensional (2D) sediment flow-through microcosms. This paper describes the versatility of such simple aquifer model systems with respect to biodegradation of aromatic hydrocarbons, i.e. toluene and ethylbenzene, under various environmental conditions. Initially constructed to study non-reactive and bioreactive transport of organic contaminants in homogeneous porous media under steady state hydraulic conditions, experimental setups developed towards more realistic heterogeneous sediment packing and transient hydraulic conditions. High-resolution spatial and temporal sampling allowed to obtain new insights on the distribution of bioactivities in contaminant plumes and associated controlling and limiting factors. Major biodegradation activities in saturated porous sediments are located at the fringes of contaminant plumes and are driven by dispersive mixing. These hot-spots of contaminant biotransformation are characterized by steep physical-chemical gradients in the millimeter to centimeter range. Sediment heterogeneity, i.e. high-conductivity zones, was shown to significantly enhance transverse mixing and subsequently biodegradation. On the contrary, transient hydraulic conditions may generate intermediate disturbances to biodegrader populations and thus may interfere with optimized contaminant conversion. However, a bacterial strain aerobically degrading toluene, i.e. Pseudomonas putida F1, was shown to adapt to vertically moving contaminant plumes, in the way that it regained full biodegradation potential two-times faster in areas with a mid-term (days to weeks) contamination history than in areas not contaminated before. The 2D flow-through microcosms facilitated to combine a number of physicochemical and microbiological methods, such as high-resolution non-invasive oxygen measurements, conservative tracer tests, compound-specific isotope analysis (CSIA), fluorescence in situ hybridization (FISH), and numerical transport modelling, to name a few. Moreover, due to the defined and well-controlled operating conditions, these bench-scale flow-through systems allow to investigate theoretical concepts and to develop and test predictive models. They represent a valuable tool in helping to bridge the current knowledge gap concerning transport and degradation of contaminants in groundwater from the small-scale (i.e. oversimplified batch systems, disregarding transport processes) to the highly complex field conditions. The promising potential of applications is by far not exhausted. Further possibilities include testing ecological theories such as the resource-ratio theory, island biogeography, area-species richness relationships and relations between community structure, microbial abundance and process rates as well as the importance and effects of bacterial chemotaxis.

3-D Interpolation in Object Perception: Evidence from an Objective Performance Paradigm

ERIC Educational Resources Information Center

Kellman, Philip J.; Garrigan, Patrick; Shipley, Thomas F.; Yin, Carol; Machado, Liana

2005-01-01

Object perception requires interpolation processes that connect visible regions despite spatial gaps. Some research has suggested that interpolation may be a 3-D process, but objective performance data and evidence about the conditions leading to interpolation are needed. The authors developed an objective performance paradigm for testing 3-D…

Family and Child Characteristics Linking Neighborhood Context and Child Externalizing Behavior

ERIC Educational Resources Information Center

Roosa, Mark W.; Deng, Shiying; Ryu, Ehri; Lockhart Burrell, Ginger; Tein, Jenn-Yun; Jones, Sarah; Lopez, Vera; Crowder, Sakina

2005-01-01

Neighborhood conditions are related to children's externalizing behavior, although few processes that help explain this association have been identified. With data from 189 primarily low-income Anglo and Mexican American families, we tested a stress process model that included 3 potential mediators of this relationship. The results showed that…

Direct Evidence for a Dual Process Model of Deductive Inference

ERIC Educational Resources Information Center

Markovits, Henry; Brunet, Marie-Laurence; Thompson, Valerie; Brisson, Janie

2013-01-01

In 2 experiments, we tested a strong version of a dual process theory of conditional inference (cf. Verschueren et al., 2005a, 2005b) that assumes that most reasoners have 2 strategies available, the choice of which is determined by situational variables, cognitive capacity, and metacognitive control. The statistical strategy evaluates inferences…

Imitation, Inspiration, and Creation: Cognitive Process of Creative Drawing by Copying Others' Artworks

ERIC Educational Resources Information Center

Okada, Takeshi; Ishibashi, Kentaro

2017-01-01

To investigate the cognitive processes underlying creative inspiration, we tested the extent to which viewing or copying prior examples impacted creative output in art. In Experiment 1, undergraduates made drawings under three conditions: (a) copying an artist's drawing, then producing an original drawing; (b) producing an original drawing without…

Weld formation during material extrusion additive manufacturing.

PubMed

Seppala, Jonathan E; Hoon Han, Seung; Hillgartner, Kaitlyn E; Davis, Chelsea S; Migler, Kalman B

2017-10-04

Material extrusion (ME) is a layer-by-layer additive manufacturing process that is now used in personal and commercial production where prototyping and customization are required. However, parts produced from ME frequently exhibit poor mechanical performance relative to those from traditional means; moreover, fundamental knowledge of the factors leading to development of inter-layer strength in this highly non-isothermal process is limited. In this work, we seek to understand the development of inter-layer weld strength from the perspective of polymer interdiffusion under conditions of rapidly changing mobility. Our framework centers around three interrelated components: in situ thermal measurements (via infrared imaging), temperature dependent molecular processes (via rheology), and mechanical testing (via mode III fracture). We develop the concept of an equivalent isothermal weld time and test its relationship to fracture energy. For the printing conditions studied the equivalent isothermal weld time for T ref = 230 °C ranged from 0.1 ms to 100 ms. The results of these analysis provide a basis for optimizing inter-layer strength, the limitations of the ME process, and guide development of new materials.

Advanced oxidation of commercial herbicides mixture: experimental design and phytotoxicity evaluation.

PubMed

López, Alejandro; Coll, Andrea; Lescano, Maia; Zalazar, Cristina

2017-05-05

In this work, the suitability of the UV/H 2 O 2 process for commercial herbicides mixture degradation was studied. Glyphosate, the herbicide most widely used in the world, was mixed with other herbicides that have residual activity as 2,4-D and atrazine. Modeling of the process response related to specific operating conditions like initial pH and initial H 2 O 2 to total organic carbon molar ratio was assessed by the response surface methodology (RSM). Results have shown that second-order polynomial regression model could well describe and predict the system behavior within the tested experimental region. It also correctly explained the variability in the experimental data. Experimental values were in good agreement with the modeled ones confirming the significance of the model and highlighting the success of RSM for UV/H 2 O 2 process modeling. Phytotoxicity evolution throughout the photolytic degradation process was checked through germination tests indicating that the phytotoxicity of the herbicides mixture was significantly reduced after the treatment. The end point for the treatment at the operating conditions for maximum TOC conversion was also identified.

Prediction of stress corrosion of carbon steel by nuclear process liquid wastes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ondrejcin, R.S.

1978-08-01

Radioactive liquid wastes are produced as a consequence of processing fuel from Savannah River Plant (SRP) production reactors. These wastes are stored in mild steel waste tanks, some of which have developed cracks from stress corrosion. A laboratory test was developed to determine the relative agressiveness of the wastes for stress corrosion cracking of mild steel. Tensile samples were strained to fracture in synthetic waste solutions in an electrochemical cell with the sample as the anode. Crack initiation is expected if total elongation of the steel in the test is less than its uniform elongation in air. Cracking would bemore » anticipated in a plant waste tank if solution conditions were equivalent to test conditions that cause a total elongation that is less than uniform elongation. The electrochemical tensile tests showed that the supernates in salt receiver tanks at SRP have the least aggressive compositions, and wastes newly generated during fuel repocessing have the most aggressive ones. Test data also verified that ASTM A 516-70 steel used in the fabrication of the later design waste tanks is less susceptible to cracking than the ASTM A 285-B steel used in earlier designs.« less

Ranking protective coatings: Laboratory vs. field experience

NASA Astrophysics Data System (ADS)

Conner, Jeffrey A.; Connor, William B.

1994-12-01

Environmentally protective coatings are used on a wide range of gas turbine components for survival in the harsh operating conditions of engines. A host of coatings are commercially available to protect hot-section components, ranging from simple aluminides to designer metallic overlays and ceramic thermal barrier coatings. A variety of coating-application processes are available, and they range from simple pack cementation processing to complex physical vapor deposition, which requires multimillion dollar facilities. Detailed databases are available for most coatings and coating/process combinations for a range of laboratory tests. Still, the analysis of components actually used in engines often yields surprises when compared against predicted coating behavior from laboratory testing. This paper highlights recent work to develop new laboratory tests that better simulate engine environments. Comparison of in-flight coating performance as well as industrial and factory engine testing on a range of hardware is presented along with laboratory predictions from standard testing and from recently developed cyclic burner-rig testing.

Time-Dependent Effects of Prazosin on the Development of Methamphetamine Conditioned Hyperactivity and Context-Specific Sensitization in Mice

PubMed Central

White, André O.; Rauhut, Anthony S.

2014-01-01

The present experiments examined the effects of prazosin, a selective α1-adrenergic receptor antagonist, on the development of methamphetamine conditioned hyperactivity and context-specific sensitization. Mice received an injection of vehicle (distilled water) or prazosin (0.5, 1.0 or 2.0 mg/kg) 30 minutes prior to a second injection of vehicle (saline) or methamphetamine (1.0 mg/kg) during the conditioning sessions (Experiment 1). Following the conditioning sessions, mice were tested for conditioned hyperactivity and then tested for context-specific sensitization. In subsequent experiments, mice received an injection of vehicle (distilled water) or prazosin (2.0 mg/kg) immediately (Experiment 2) or 24 hours (Experiment 3) after the conditioning sessions and then tested for conditioned hyperactivity and context-specific sensitization. Prazosin dose-dependently blocked the development of methamphetamine conditioned hyperactivity and context-specific sensitization when administered prior to the methamphetamine during the conditioning phase; however nonspecific motor impairments also were observed (Experiment 1). Immediate (Experiment 2), but not the 24-hour delay (Experiment 3), post-session administration of prazosin attenuated the development of methamphetamine conditioned hyperactivity and context-specific sensitization. Nonspecific motor impairments were not observed in these latter experiments. Collectively, these results suggest that the α1-adrenergic receptor mediates the development of methamphetamine-conditioned hyperactivity and context-specific sensitization, perhaps by altering memory consolidation and/or reconsolidation processes. PMID:24487011

Probing numerical Laplace inversion methods for two and three-site molecular exchange between interconnected pore structures.

PubMed

Silletta, Emilia V; Franzoni, María B; Monti, Gustavo A; Acosta, Rodolfo H

2018-01-01

Two-dimension (2D) Nuclear Magnetic Resonance relaxometry experiments are a powerful tool extensively used to probe the interaction among different pore structures, mostly in inorganic systems. The analysis of the collected experimental data generally consists of a 2D numerical inversion of time-domain data where T 2 -T 2 maps are generated. Through the years, different algorithms for the numerical inversion have been proposed. In this paper, two different algorithms for numerical inversion are tested and compared under different conditions of exchange dynamics; the method based on Butler-Reeds-Dawson (BRD) algorithm and the fast-iterative shrinkage-thresholding algorithm (FISTA) method. By constructing a theoretical model, the algorithms were tested for a two- and three-site porous media, varying the exchange rates parameters, the pore sizes and the signal to noise ratio. In order to test the methods under realistic experimental conditions, a challenging organic system was chosen. The molecular exchange rates of water confined in hierarchical porous polymeric networks were obtained, for a two- and three-site porous media. Data processed with the BRD method was found to be accurate only under certain conditions of the exchange parameters, while data processed with the FISTA method is precise for all the studied parameters, except when SNR conditions are extreme. Copyright © 2017 Elsevier Inc. All rights reserved.

Worrying affects associative fear learning: a startle fear conditioning study.

PubMed

Gazendam, Femke J; Kindt, Merel

2012-01-01

A valuable experimental model for the pathogenesis of anxiety disorders is that they originate from a learned association between an intrinsically non-aversive event (Conditioned Stimulus, CS) and an anticipated disaster (Unconditioned Stimulus, UCS). Most anxiety disorders, however, do not evolve from a traumatic experience. Insights from neuroscience show that memory can be modified post-learning, which may elucidate how pathological fear can develop after relatively mild aversive events. Worrying--a process frequently observed in anxiety disorders--is a potential candidate to strengthen the formation of fear memory after learning. Here we tested in a discriminative fear conditioning procedure whether worry strengthens associative fear memory. Participants were randomly assigned to either a Worry (n = 23) or Control condition (n = 25). After fear acquisition, the participants in the Worry condition processed six worrisome questions regarding the personal aversive consequences of an electric stimulus (UCS), whereas the Control condition received difficult but neutral questions. Subsequently, extinction, reinstatement and re-extinction of fear were tested. Conditioned responding was measured by fear-potentiated startle (FPS), skin conductance (SCR) and UCS expectancy ratings. Our main results demonstrate that worrying resulted in increased fear responses (FPS) to both the feared stimulus (CS(+)) and the originally safe stimulus (CS(-)), whereas FPS remained unchanged in the Control condition. In addition, worrying impaired both extinction and re-extinction learning of UCS expectancy. The implication of our findings is that they show how worry may contribute to the development of anxiety disorders by affecting associative fear learning.

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue of SLM-IN718

NASA Technical Reports Server (NTRS)

Lambert, D. M.

2016-01-01

The surface finish of parts produced by additive manufacturing processes is much rougher than the surface finish generated by machining processes, and a rougher surface can reduce the fatigue strength of a part. This paper discusses an effort to quantify that reduction of strength in high-cycle fatigue for selective laser melt (SLM) coupons. A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the SLM process. This factor is the percentage reduction from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition at the same fatigue life. Specimens were provided by a number of vendors, free to use their "best practice"; only one heat treat condition was considered; and several test temperatures were characterized, including room temperature, 800F, 1000F, and 1200F. The 1000F data had a large variance, and was omitted from consideration in this document. A first method used linear approximations extracted from the graphs, and only where data was available for both. A recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness no more than 4 micro-inches/inch) was established at approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce a similar life in the as-built surface condition. In this first evaluation, the knockdown factor did not appear to be a function of temperature. A second approach, the "KP method", incorporated the surface finish measure into a new parameter termed the pseudo-stress intensity factor, Kp, which was formulated to be similar to the fracture mechanics stress intensity factor. Using Kp, the variance seemed to be reduced across all sources, and knockdown factors were estimated using Kp over the range where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown might be lower than the knockdown observed above about one million cycles, where it tended to stabilize. This was not universal for all temperatures tested. The higher temperature tests are thought to be influenced by the test temperature, which perhaps continued the aging process. Further evaluation of the method is suggested.

Mechanical and tribological behaviour of molten salt processed self-lubricated aluminium composite under different treatments

NASA Astrophysics Data System (ADS)

Kannan, C.; Ramanujam, R.

2018-05-01

The aim of this research work is to evaluate the mechanical and tribological behaviour of Al 7075 based self-lubricated hybrid nanocomposite under different treated conditions viz. as-cast, T6 and deep cryo treated. In order to overcome the drawbacks associated with conventional stir casting, a combinational approach that consists of molten salt processing, ultrasonic assistance and optimized mechanical stirring is adopted in this study to fabricate the nanocomposite. The mechanical characterisation tests carried out on this nanocomposite reveals an improvement of about 39% in hardness and 22% in ultimate tensile strength possible under T6 condition. Under specific conditions, the wear rate can be reduced to the extent of about 63% through the usage of self-lubricated hybrid nanocomposite under T6 condition.

Design of an MR image processing module on an FPGA chip

NASA Astrophysics Data System (ADS)

Li, Limin; Wyrwicz, Alice M.

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments.

Microstructure and mechanical properties of nickel coated multi walled carbon nanotube reinforced stainless steel 316L matrix composites by laser sintering process

NASA Astrophysics Data System (ADS)

Mahanthesha, P.; Mohankumar, G. C.

2018-04-01

Electroless Ni coated Multi-walled Carbon nanotubes reinforced with Stainless Steel 316L matrix composite was developed by Direct Metal Laser Sintering process (DMLS). Homogeneous mixture of Stainless Steel 316L powder and carbon nanotubes in different vol. % was obtained by using double cone blender machine. Characterization of electroless Ni coated carbon nanotubes was done by using X-ray diffraction, FESEM and EDS. Test samples were fabricated at different laser scan speeds. Effect of process parameters and CNT vol. % content on solidification microstructure and mechanical properties of test samples was investigated by using Optical microscopy, FESEM, and Hounsfield tensometer. Experimental results reveal DMLS process parameters affect the density and microstructure of sintered parts. Dense parts with minimum porosity when processed at low laser scan speeds and low CNT vol. %. Tensile fractured surface of test specimens evidences the survival of carbon nanotubes under high temperature processing condition.

Design of an MR image processing module on an FPGA chip

PubMed Central

Li, Limin; Wyrwicz, Alice M.

2015-01-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128 × 128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. PMID:25909646

A Comparison of seismic instrument noise coherence analysis techniques

USGS Publications Warehouse

Ringler, A.T.; Hutt, C.R.; Evans, J.R.; Sandoval, L.D.

2011-01-01

The self-noise of a seismic instrument is a fundamental characteristic used to evaluate the quality of the instrument. It is important to be able to measure this self-noise robustly, to understand how differences among test configurations affect the tests, and to understand how different processing techniques and isolation methods (from nonseismic sources) can contribute to differences in results. We compare two popular coherence methods used for calculating incoherent noise, which is widely used as an estimate of instrument self-noise (incoherent noise and self-noise are not strictly identical but in observatory practice are approximately equivalent; Holcomb, 1989; Sleeman et al., 2006). Beyond directly comparing these two coherence methods on similar models of seismometers, we compare how small changes in test conditions can contribute to incoherent-noise estimates. These conditions include timing errors, signal-to-noise ratio changes (ratios between background noise and instrument incoherent noise), relative sensor locations, misalignment errors, processing techniques, and different configurations of sensor types.

Eagle-eyed visual acuity: an experimental investigation of enhanced perception in autism.

PubMed

Ashwin, Emma; Ashwin, Chris; Rhydderch, Danielle; Howells, Jessica; Baron-Cohen, Simon

2009-01-01

Anecdotal accounts of sensory hypersensitivity in individuals with autism spectrum conditions (ASC) have been noted since the first reports of the condition. Over time, empirical evidence has supported the notion that those with ASC have superior visual abilities compared with control subjects. However, it remains unclear whether these abilities are specifically the result of differences in sensory thresholds (low-level processing), rather than higher-level cognitive processes. This study investigates visual threshold in n = 15 individuals with ASC and n = 15 individuals without ASC, using a standardized optometric test, the Freiburg Visual Acuity and Contrast Test, to investigate basic low-level visual acuity. Individuals with ASC have significantly better visual acuity (20:7) compared with control subjects (20:13)-acuity so superior that it lies in the region reported for birds of prey. The results of this study suggest that inclusion of sensory hypersensitivity in the diagnostic criteria for ASC may be warranted and that basic standardized tests of sensory thresholds may inform causal theories of ASC.

Lumen claims of the STERRAD 100NX sterilizer: testing performance limits when processing equipment containing long, narrow lumens.

PubMed

Diab-Elschahawi, Magda; Blacky, Alexander; Bachhofner, Nicole; Koller, Walter

2011-11-01

According to manufacturers information, the STERRAD 100NX sterilizer-a low temperature H(2)O(2) gas plasma sterilizer-can adequately process single channel stainless steel lumens with an inside diameter of 0.7 mm or larger and a maximum length of 500 mm using standard cycle sterilizing conditions. The aim of this study was to qualify the performance of this H(2)O(2) gas plasma sterilizer under different experimental settings representing worst case conditions. Inoculated carriers were placed at the midpoint position of specified lumens and then submitted to flex scope sterilizing conditions. To simulate insufficient cleaning or crystalline residues, we added organic and inorganic challenges to our inoculated carriers. For experiments done with unchallenged carriers, quantitative analysis reached a log(10) reduction rate of ≥5.71, whereas qualitative results showed no growth in 24 out of 30 biologic indicators tested using flex scope half cycle conditions. Any additional kind of challenge significantly impaired the sterilization outcome. The findings of our current study emphasize the importance of a thorough validated cleaning of medical devices as well as timing for cleaning and decontamination before being exposed to the H(2)O(2) sterilization process and, furthermore, the need for strict adherence to manufacturer's recommendations. Copyright © 2011 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Locomotor sensory organization test: a novel paradigm for the assessment of sensory contributions in gait.

PubMed

Chien, Jung Hung; Eikema, Diderik-Jan Anthony; Mukherjee, Mukul; Stergiou, Nicholas

2014-12-01

Feedback based balance control requires the integration of visual, proprioceptive and vestibular input to detect the body's movement within the environment. When the accuracy of sensory signals is compromised, the system reorganizes the relative contributions through a process of sensory recalibration, for upright postural stability to be maintained. Whereas this process has been studied extensively in standing using the Sensory Organization Test (SOT), less is known about these processes in more dynamic tasks such as locomotion. In the present study, ten healthy young adults performed the six conditions of the traditional SOT to quantify standing postural control when exposed to sensory conflict. The same subjects performed these six conditions using a novel experimental paradigm, the Locomotor SOT (LSOT), to study dynamic postural control during walking under similar types of sensory conflict. To quantify postural control during walking, the net Center of Pressure sway variability was used. This corresponds to the Performance Index of the center of pressure trajectory, which is used to quantify postural control during standing. Our results indicate that dynamic balance control during locomotion in healthy individuals is affected by the systematic manipulation of multisensory inputs. The sway variability patterns observed during locomotion reflect similar balance performance with standing posture, indicating that similar feedback processes may be involved. However, the contribution of visual input is significantly increased during locomotion, compared to standing in similar sensory conflict conditions. The increased visual gain in the LSOT conditions reflects the importance of visual input for the control of locomotion. Since balance perturbations tend to occur in dynamic tasks and in response to environmental constraints not present during the SOT, the LSOT may provide additional information for clinical evaluation on healthy and deficient sensory processing.

Wear Properties of ECAP-Processed AM80 Magnesium Alloy

NASA Astrophysics Data System (ADS)

Gopi, K. R.; Shivananda Nayaka, H.; Sahu, Sandeep

2017-07-01

AM80 magnesium alloy was subjected to equal-channel angular pressing (ECAP), and microstructural evolution was studied using scanning electron microscope (SEM). Grain size was found to decrease up to 3 µm after four passes. An increase in number of ECAP passes led to a corresponding increase in hardness of the processed samples. Unprocessed and ECAP-processed samples were subjected to wear test using pin-on-disk wear test machine to study the wear behavior. Effects of varying loads (30 and 40 N) with sliding distances (2500 and 5000 m) were studied. The results showed reduction in wear mass loss for the ECAP-processed samples in comparison with unprocessed condition. Coefficient of friction (COF) was studied for different loads, and improvement in COF values was observed for ECAP-processed samples compared to unprocessed condition. Worn surfaces were studied using SEM and energy-dispersive x-ray spectrometer, and they exhibited plastic deformation, delamination, plowing, wear debris and oxidation in the sliding direction. X-ray diffraction analysis was conducted on the worn surfaces to identify the phases. It revealed the presence of magnesium oxide and magnesium aluminum oxide which led to oxidation wear in the sliding direction. Wear mechanism was found to be abrasive and oxidation wear.

On-line IR analyzer system to monitor cephamycin C loading on ion-exchange resin

NASA Astrophysics Data System (ADS)

Shank, Sheldon; Russ, Warren; Gravatt, Douglas; Lee, Wesley; Donahue, Steven M.

1992-08-01

An on-line infrared analyzer is being developed for monitoring cephamycin C loading on ion exchange resin. Accurate measurement of product loading offers productivity improvements with direct savings from product loss avoidance, minimized raw material cost, and reduced off-line laboratory testing. Ultrafiltered fermentation broth is fed onto ion exchange columns under conditions which adsorb the product, cephamycin C, to the resin while allowing impurities to pass unretained. Product loading is stopped when the on-line analyzer determines that resin capacity for adsorbing product is nearly exhausted. Infrared spectroscopy has been shown capable of quantifying cephamycin C in the process matrix at concentrations that support process control decisions. Process-to-analyzer interface challenges have been resolved, including sample conditioning requirements. Analyzer requirements have been defined. The sample conditioning station is under design.

Mechanical Behaviour of Conventional Materials at Experimental Conditions of Deep Drawing Technological Process

NASA Astrophysics Data System (ADS)

Nikolov, N.; Pashkouleva, D.; Kavardzhikov, V.

2012-09-01

The paper deals with experimental investigations on the mechanical behaviour of body-centred-cubic (BCC) and face-centred-cubic (FCC)-conventionally structured sheet metalic-metalic materials under stress-strain conditions of a deep drawing process determined by a coefficient close to the limiting one for Steel 08 and punch diameter of 50 mm. The mechanical characteristics of the investigated materials are identified by one-dimensional tension tests. The materials' responses, as results of identical loading conditions, are described by the change of blank sizes and characteristics of the forming processes. The chosen deformation path ensures obtaining a qualitative steel piece and leads to failures of aluminium and brass blanks. The reported results could be useful for investigations and predictions of the mechanical responses of such type metallic structures applying microscopic instrumented observations and numerical simulations.

The fate of MtBE during Fenton-like treatments through laboratory scale column tests.

PubMed

Piscitelli, Daniela; Zingaretti, Daniela; Verginelli, Iason; Gavasci, Renato; Baciocchi, Renato

2015-12-01

In Situ Chemical Oxidation (ISCO) based on the Fenton's process is a proven technology for the treatment of groundwater contaminated by organic compounds. Nevertheless, the application of this treatment process to methyl tert-butyl ether (MtBE) is questioned, as there are concerns about its capacity to achieve complete mineralization. Many existing studies have focused on water contaminated by MtBE and are thus not representative of in situ treatments since they do not consider the presence of soil. In this work, the effectiveness of a Fenton-like process for MtBE treatment was proven in soil column tests performed at operating conditions (i.e., oxidant and contaminant concentration and flow rates) resembling those typically used for in situ applications. No MtBE by-products were detected in any of the tested conditions, thus suggesting that the tert-butyl group of MtBE was completely degraded. A mass balance based on the CO2 produced was used as evidence that most of the MtBE removed was actually mineralized. Finally, the obtained results show that preconditioning of soil with a chelating agent (EDTA) significantly enhanced MtBE oxidation. Copyright © 2015 Elsevier B.V. All rights reserved.

Ergonomic Work Station Design to Improve Workload Quality and Productivity of the Craffsmen

NASA Astrophysics Data System (ADS)

Widana, IK; Wayan Sumetri, Ni; Ketut Sutapa, I.

2018-01-01

This study is a research on ergonomics field, especially for ergonomics work station. This research begins with direct observation on the work process of carving craft. In addition to the aspect of occupational health, the stages of the process are also subject matter in the effort to solve the research problem. In accordance with the master plan of research of Bali State Polytechnic, problem solving will be focused on human aspect and utilization of appropriate technology, so that will get the work process ENASEP (effective, convenient, safe, healthy, efficient and productive) Technical easy to work, economical, ergonomic, energy saving, environmentally friendly and in accordance with the trend of the era. The method to be used in this research is experimental with the same subject design. Involves 9 samples who perform activities on conditions before and after treatment. Data on environmental conditions were analyzed by Mann-Whitney test. Data on work productivity and workload were tested with two pair sample t-test at a significance level of 5%. The results showed that by utilizing ergonomic work stations, occupational health indicators such as workload showed better signs, indicated by decreased the workload. In addition to occupational health, productivity indicators also increased significantly.

Memory load as a cognitive antidote to performance decrements in data entry.

PubMed

Chapman, Mary J; Healy, Alice F; Kole, James A

2016-10-01

In two experiments, subjects trained in data entry, typing one 4-digit number at a time. At training, subjects either typed the numbers immediately after they appeared (immediate) or typed the previous number from memory while viewing the next number (delayed). In Experiment 2 stimulus presentation time was limited and either nothing or a space (gap) was inserted between the second and third digits. In both experiments after training, all subjects completed a test with no gap and typed numbers immediately. Training with a memory load improved speed across training blocks (Experiment 1) and eliminated the decline in accuracy across training blocks (Experiment 2), thus serving as a cognitive antidote to performance decrements. An analysis of each keystroke revealed different underlying processes and strategies for the two training conditions, including when encoding took place. Chunking (in which the first and last two digits are treated separately) was more evident in the immediate than in the delayed condition and was exaggerated with a gap, even at test when there was no gap. These results suggest that such two-digit chunking is due to stimulus encoding and motor planning processes as well as memory, and those processes transferred from training to testing.

Enhancing divergent thinking in visual arts education: Effects of explicit instruction of meta-cognition.

PubMed

van de Kamp, Marie-Thérèse; Admiraal, Wilfried; van Drie, Jannet; Rijlaarsdam, Gert

2015-03-01

The main purposes of visual arts education concern the enhancement of students' creative processes and the originality of their art products. Divergent thinking is crucial for finding original ideas in the initial phase of a creative process that aims to result in an original product. This study aims to examine the effects of explicit instruction of meta-cognition on students' divergent thinking. A quasi-experimental design was implemented with 147 secondary school students in visual arts education. In the experimental condition, students attended a series of regular lessons with assignments on art reception and production, and they attended one intervention lesson with explicit instruction of meta-cognition. In the control condition, students attended a series of regular lessons only. Pre-test and post-test instances tests measured fluency, flexibility, and originality as indicators of divergent thinking. Explicit instruction of meta-cognitive knowledge had a positive effect on fluency and flexibility, but not on originality. This study implies that in the domain of visual arts, instructional support in building up meta-cognitive knowledge about divergent thinking may improve students' creative processes. This study also discusses possible reasons for the demonstrated lack of effect for originality. © 2014 The British Psychological Society.

Biocatalytic and chemical leaching of a low-grade nickel laterite ore

NASA Astrophysics Data System (ADS)

Ciftci, Hasan; Atik, Suleyman; Gurbuz, Fatma

2018-04-01

Nickel and cobalt recovery from a low-grade nickel laterite ore, supplied from Çaldağ deposit (Manisa, Turkey) were investigated by bio and chemical leaching processes. The fungus, Aspergillus niger was used for biocatalytic leaching experiments. The effects of parameters (solid ratio and sucrose concentration) on the biocatalytic leaching of the ore were initially tested in flasks to obtain the optimum conditions for the A. niger. Then chemical leaching was applied as a comparison to bioleaching, using organic acids (citric, oxalic, acetic and gluconic acids) as well as a mixture of acids. According the results, the maximum dissolution yield of nickel, cobalt and iron were detected respectively as 95.3%, 74.3% and 50.0% by biocatalytic processes which containing 25% (w/v) sucrose and 1% (w/v) solids. The increase in the solid ratio adversely influenced the biocatalytic activity of A. niger. Finally, further tests in reactors (v = 1 and 10 L) were performed using the optimum conditions from the flask tests. The difference in metals recovery between biocatalytic and chemical leaching was significantly important. Bioleaching produced higher Ni and Co extractions (34.3-75.6%) than chemical process.

Crack propagation monitoring in a full-scale aircraft fatigue test based on guided wave-Gaussian mixture model

NASA Astrophysics Data System (ADS)

Qiu, Lei; Yuan, Shenfang; Bao, Qiao; Mei, Hanfei; Ren, Yuanqiang

2016-05-01

For aerospace application of structural health monitoring (SHM) technology, the problem of reliable damage monitoring under time-varying conditions must be addressed and the SHM technology has to be fully validated on real aircraft structures under realistic load conditions on ground before it can reach the status of flight test. In this paper, the guided wave (GW) based SHM method is applied to a full-scale aircraft fatigue test which is one of the most similar test status to the flight test. To deal with the time-varying problem, a GW-Gaussian mixture model (GW-GMM) is proposed. The probability characteristic of GW features, which is introduced by time-varying conditions is modeled by GW-GMM. The weak cumulative variation trend of the crack propagation, which is mixed in time-varying influence can be tracked by the GW-GMM migration during on-line damage monitoring process. A best match based Kullback-Leibler divergence is proposed to measure the GW-GMM migration degree to reveal the crack propagation. The method is validated in the full-scale aircraft fatigue test. The validation results indicate that the reliable crack propagation monitoring of the left landing gear spar and the right wing panel under realistic load conditions are achieved.

Impregnation of cinnamaldehyde into cassava starch biocomposite films using supercritical fluid technology for the development of food active packaging.

PubMed

de Souza, Ana Cristina; Dias, Ana M A; Sousa, Hermínio C; Tadini, Carmen C

2014-02-15

In this work, supercritical solvent impregnation (SSI) has been tested for the incorporation of natural compounds into biocomposite materials for food packaging. Cinnamaldehyde, with proved antimicrobial activity against fungi commonly found in bread products, was successfully impregnated on biocomposite cassava starch based materials using supercritical carbon dioxide as solvent. Different process experimental conditions were tested (pressure, impregnation time and depressurization rate) at a fixed temperature (35 °C) in order to study their influence on the amount of impregnated cinnamaldehyde as well as on the morphology of the films. Results showed that all conditions permitted to impregnate antimicrobial active amounts superior to those previously obtained using conventional incorporation methods. Moreover, a significant decrease of the equilibrium water vapor sorption capacity and water vapor permeability of the films was observed after SSI processing which is a clear advantage of the process, considering the envisaged applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Shared Processing of Language and Music.

PubMed

Atherton, Ryan P; Chrobak, Quin M; Rauscher, Frances H; Karst, Aaron T; Hanson, Matt D; Steinert, Steven W; Bowe, Kyra L

2018-01-01

The present study sought to explore whether musical information is processed by the phonological loop component of the working memory model of immediate memory. Original instantiations of this model primarily focused on the processing of linguistic information. However, the model was less clear about how acoustic information lacking phonological qualities is actively processed. Although previous research has generally supported shared processing of phonological and musical information, these studies were limited as a result of a number of methodological concerns (e.g., the use of simple tones as musical stimuli). In order to further investigate this issue, an auditory interference task was employed. Specifically, participants heard an initial stimulus (musical or linguistic) followed by an intervening stimulus (musical, linguistic, or silence) and were then asked to indicate whether a final test stimulus was the same as or different from the initial stimulus. Results indicated that mismatched interference conditions (i.e., musical - linguistic; linguistic - musical) resulted in greater interference than silence conditions, with matched interference conditions producing the greatest interference. Overall, these results suggest that processing of linguistic and musical information draws on at least some of the same cognitive resources.

A validation study of the 1,2-indandione reagent for operational use in the UK: Part 2 - Optimization of processing conditions.

PubMed

Nicolasora, Niko; Downham, Rory; Dyer, Rachel-May; Hussey, Laura; Luscombe, Aoife; Sears, Vaughn

2018-05-02

This paper contains details of work carried out to identify the most effective processing conditions for the optimized 1,2-indandione/zn formulation developed for use under UK conditions. Using direct measurements of fluorescence taken from test spots of amino acids and eccrine sweat during oven processing, complemented with experiments on real fingermarks, it was established that processing temperatures above 120°C in the oven were detrimental to the fluorescence of the developed mark. Alternative methods of development to oven processing were found to be effective, but less controllable. High levels of humidification were also found to be detrimental to the fluorescence of 1,2-indandione developed marks, and oven processing at 100°C and 0% relative humidity is therefore recommended for further studies. It has also been shown that 1,2-indandione can develop fingermarks at temperatures as low as 20°C, making it a candidate for use at crime scenes. Copyright © 2018. Published by Elsevier B.V.

On the nature of extraversion: variation in conditioned contextual activation of dopamine-facilitated affective, cognitive, and motor processes

PubMed Central

Depue, Richard A.; Fu, Yu

2013-01-01

Research supports an association between extraversion and dopamine (DA) functioning. DA facilitates incentive motivation and the conditioning and incentive encoding of contexts that predict reward. Therefore, we assessed whether extraversion is related to the efficacy of acquiring conditioned contextual facilitation of three processes that are dependent on DA: motor velocity, positive affect, and visuospatial working memory. We exposed high and low extraverts to three days of association of drug reward (methylphenidate, MP) with a particular laboratory context (Paired group), a test day of conditioning, and three days of extinction in the same laboratory. A Placebo group and an Unpaired group (that had MP in a different laboratory context) served as controls. Conditioned contextual facilitation was assessed by (i) presenting video clips that varied in their pairing with drug and laboratory context and in inherent incentive value, and (ii) measuring increases from day 1 to Test day on the three processes above. Results showed acquisition of conditioned contextual facilitation across all measures to video clips that had been paired with drug and laboratory context in the Paired high extraverts, but no conditioning in the Paired low extraverts (nor in either of the control groups). Increases in the Paired high extraverts were correlated across the three measures. Also, conditioned facilitation was evident on the first day of extinction in Paired high extraverts, despite the absence of the unconditioned effects of MP. By the last day of extinction, responding returned to day 1 levels. The findings suggest that extraversion is associated with variation in the acquisition of contexts that predict reward. Over time, this variation may lead to differences in the breadth of networks of conditioned contexts. Thus, individual differences in extraversion may be maintained by activation of differentially encoded central representations of incentive contexts that predict reward. PMID:23785330

Physiological response of invasive mussel Limnoperna fortunei (Dunker, 1857) (Bivalvia: Mytilidae) submitted to transport and experimental conditions.

PubMed

Cordeiro, N I S; Andrade, J T M; Montresor, L C; Luz, D M R; Araújo, J M; Martinez, C B; Pinheiro, J; Vidigal, T H D A

2017-03-01

Successful animal rearing under laboratory conditions for commercial processes or laboratory experiments is a complex chain that includes several stressors (e.g., sampling and transport) and incurs, as a consequence, the reduction of natural animal conditions, economic losses and inconsistent and unreliable biological results. Since the invasion of the bivalve Limnoperna fortunei (Dunker, 1857) in South America, several studies have been performed to help control and manage this fouling pest in industrial plants that use raw water. Relatively little attention has been given to the laboratory rearing procedure of L. fortunei, its condition when exposed to a stressor or its acclimation into laboratory conditions. Considering this issue, the aims of this study are to (i) investigate L. fortunei physiological responses when submitted to the depuration process and subsequent air transport (without water/dry condition) at two temperatures, based on glycogen concentrations, and (ii) monitor the glycogen concentrations in different groups when maintained for 28 days under laboratory conditions. Based on the obtained results, depuration did not affect either of the groups when they were submitted to approximately eight hours of transport. The variation in glycogen concentration among the specimens that were obtained from the field under depurated and non-depurated conditions was significant only in the first week of laboratory growth for the non-depurated group and in the second week for the depurated group. In addition, the tested temperature did not affect either of the groups that were submitted to transport. The glycogen concentrations were similar to those of the specimens that were obtained from the field in third week, which suggests that the specimens acclimated to laboratory conditions during this period of time. Thus, the results indicate that the air transport and acclimation time can be successfully incorporated into experimental studies of L. fortunei. Finally, the tolerance of L. fortunei specimens to the stressor tested herein can help us understand the invasive capacity of this mussel during the establishment process.

Determination of Particular Endogenous Fires Hazard Zones in Goaf with Caving of Longwall

NASA Astrophysics Data System (ADS)

Tutak, Magdalena; Brodny, Jaroslaw

2017-12-01

Hazard of endogenous fires is one of the basic and common presented occupational safety hazards in coal mine in Poland and in the world. This hazard means possibility of coal self-ignition as the result of its self-heating process in mining heading or its surrounding. In underground coal-mining during ventilating of operating longwalls takes place migration of parts of airflow to goaf with caving. In a case when in these goaf a coal susceptible to selfignition occurs, then the airflow through these goaf may influence on formation of favourable conditions for coal oxidation and subsequently to its self-heating and self-ignition. Endogenous fire formed in such conditions can pose a serious hazard for the crew and for continuity of operation of mining plant. From the practical point of view, a very significant meaning has determination of the zone in the goaf with caving, in which necessary conditions for occurrence of endogenous fire are fulfilled. In the real conditions determination of such a zone is practically impossible. Therefore, authors of paper developed a methodology of determination of this zone basing on the results of modelling tests. This methodology includes a development of model of tested area, determination of boundary conditions and carrying out the simulation calculations. Based on the obtained results particular hazardous zone of endogenous fire is determined. A base for development of model of investigated region and selection of boundary conditions are the results of real tests. In the paper fundamental assumption of developed methodology, particularly in a range of assumed hazard criterion and sealing coefficient of goaf with caving were discussed. Also a mathematical model of gas flow through the porous media was characterized. Example of determination of a zone particularly endangered by endogenous fire for real system of mining heading in one of the hard coal mine was presented. Longwall ventilated in the „Y” system was subjected to the tests. For determined mining-geological conditions, the critical value of velocity of airflow and oxygen concentration in goaf, conditioning initiation of coal oxidation process were determined. For calculations ANSYS Fluent software based on finite volume method, which enable very precisely to determine the physical and chemical air and parameters at any point of tested mining heading and goaf with caving was used. Such precisely determination of these parameters on the base of the test in real conditions is practically impossible. Obtained results allowed to take early proper actions in order to limit the occurrence of endogenous fire. One can conclude, that presented methodology creates great possibilities of practical application of modelling tests for improvement of the occupational safety state in mine.

The structure-property relationships of powder processed Fe-Al-Si alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prichard, Paul D.

1998-02-23

Iron-aluminum alloys have been extensively evaluated as semi-continuous product such as sheet and bar, but have not been evaluated by net shape P/M processing techniques such as metal injection molding. The alloy compositions of iron-aluminum alloys have been optimized for room temperature ductility, but have limited high temperature strength. Hot extruded powder alloys in the Fe-Al-Si system have developed impressive mechanical properties, but the effects of sintering on mechanical properties have not been explored. This investigation evaluated three powder processed Fe-Al-Si alloys: Fe-15Al, Fe-15Al-2.8Si, Fe-15Al-5Si (atomic %). The powder alloys were produced with a high pressure gas atomization (HPGA) processmore » to obtain a high fraction of metal injection molding (MIM) quality powder (D 84 < 32 μm). The powders were consolidated either by P/M hot extrusion or by vacuum sintering. The extruded materials were near full density with grain sizes ranging from 30 to 50 μm. The vacuum sintering conditions produced samples with density ranging from 87% to 99% of theoretical density, with an average grain size ranging from 26 μm to 104 μm. Mechanical property testing was conducted on both extruded and sintered material using a small punch test. Tensile tests were conducted on extruded bar for comparison with the punch test data. Punch tests were conducted from 25 to 550 C to determine the yield strength, and fracture energy for each alloy as a function of processing condition. The ductile to brittle transition temperature (DBTT) was observed to increase with an increasing silicon content. The Fe-15Al-2.8Si alloy was selected for more extensive testing due to the combination of high temperature strength and low temperature toughness due to the two phase α + DO 3 structure. This investigation provided a framework for understanding the effects of silicon in powder processing and mechanical property behavior of Fe-Al-Si alloys.« less

The PSI Artist Project: Aerosol Retention and Accident Management Issues Following a Steam Generator Tube Rupture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guntay, Salih; Dehbi, Abdel; Suckow, Detlef

2002-07-01

Steam generator tube rupture (SGTR) incidents, such as those, which occurred in various operating pressurized, water reactors in the past, are serious operational concerns and remain among the most risk-dominant events. Although considerable efforts have been spent to understand tube degradation processes, develop improved modes of operation, and take preventative and corrective measures, SGTR incidents cannot be completely ruled out. Under certain conditions, high releases of radionuclides to the environment are possible during design basis accidents (DBA) and severe accidents. The severe accident codes' models for aerosol retention in the secondary side of a steam generator (SG) have not beenmore » assessed against any experimental data, which means that the uncertainties in the source term following an un-isolated SGTR concurrent with a severe accident are not currently quantified. The accident management (AM) procedures aim at avoiding or minimizing the release of fission products from the SG. The enhanced retention of activity within the SG defines the effectiveness of the accident management actions for the specific hardware characteristics and accident conditions of concern. A sound database on aerosol retention due to natural processes in the SG is not available, nor is an assessment of the effect of management actions on these processes. Hence, the effectiveness of the AM in SGTR events is not presently known. To help reduce uncertainties relating to SGTR issues, an experimental project, ARTIST (Aerosol Trapping In a Steam generator), has been initiated at the Paul Scherrer Institut to address aerosol and droplet retention in the various parts of the SG. The test section is comprised of a scaled-down tube bundle, a full-size separator and a full-size dryer unit. The project will study phenomena at the separate effect and integral levels and address AM issues in seven distinct phases: Aerosol retention in 1) the broken tube under dry secondary side conditions, 2) the near field close to break under dry conditions, 3) the bundle far-field under dry conditions, 4) the separator and dryer under dry conditions, 5) the bundle section under wet conditions, 6) droplet retention in the separator and dryer sections and 7) the overall SG (integral tests). Prototypical test parameters are selected to cover the range of conditions expected in severe accident as well as DBA scenarios. This paper summarizes the relevant issues and introduces the ARTIST facility and the provisional test program which will run between 2003 and 2007. (authors)« less

Investigation of Current Methods to Identify Helicopter Gear Health

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Lewicki, David G.; Le, Dy D.

2007-01-01

This paper provides an overview of current vibration methods used to identify the health of helicopter transmission gears. The gears are critical to the transmission system that provides propulsion, lift and maneuvering of the helicopter. This paper reviews techniques used to process vibration data to calculate conditions indicators (CI's), guidelines used by the government aviation authorities in developing and certifying the Health and Usage Monitoring System (HUMS), condition and health indicators used in commercial HUMS, and different methods used to set thresholds to detect damage. Initial assessment of a method to set thresholds for vibration based condition indicators applied to flight and test rig data by evaluating differences in distributions between comparable transmissions are also discussed. Gear condition indicator FM4 values are compared on an OH58 helicopter during 14 maneuvers and an OH58 transmission test stand during crack propagation tests. Preliminary results show the distributions between healthy helicopter and rig data are comparable and distributions between healthy and damaged gears show significant differences.

Investigation of Current Methods to Identify Helicopter Gear Health

NASA Technical Reports Server (NTRS)

Dempsey, Paula J.; Lewicki, David G.; Le, Dy D.

2007-01-01

This paper provides an overview of current vibration methods used to identify the health of helicopter transmission gears. The gears are critical to the transmission system that provides propulsion, lift and maneuvering of the helicopter. This paper reviews techniques used to process vibration data to calculate conditions indicators (CI s), guidelines used by the government aviation authorities in developing and certifying the Health and Usage Monitoring System (HUMS), condition and health indicators used in commercial HUMS, and different methods used to set thresholds to detect damage. Initial assessment of a method to set thresholds for vibration based condition indicators applied to flight and test rig data by evaluating differences in distributions between comparable transmissions are also discussed. Gear condition indicator FM4 values are compared on an OH58 helicopter during 14 maneuvers and an OH58 transmission test stand during crack propagation tests. Preliminary results show the distributions between healthy helicopter and rig data are comparable and distributions between healthy and damaged gears show significant differences.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandell, John F.; Ashwill, Thomas D.; Wilson, Timothy J.

This report presents an analysis of trends in fatigue results from the Montana State University program on the fatigue of composite materials for wind turbine blades for the period 2005-2009. Test data can be found in the SNL/MSU/DOE Fatigue of Composite Materials Database which is updated annually. This is the fifth report in this series, which summarizes progress of the overall program since its inception in 1989. The primary thrust of this program has been research and testing of a broad range of structural laminate materials of interest to blade structures. The report is focused on current types of infusedmore » and prepreg blade materials, either processed in-house or by industry partners. Trends in static and fatigue performance are analyzed for a range of materials, geometries and loading conditions. Materials include: sixteen resins of three general types, five epoxy based paste adhesives, fifteen reinforcing fabrics including three fiber types, three prepregs, many laminate lay-ups and process variations. Significant differences in static and fatigue performance and delamination resistance are quantified for particular materials and process conditions. When blades do fail, the likely cause is fatigue in the structural detail areas or at major flaws. The program is focused strongly on these issues in addition to standard laminates. Structural detail tests allow evaluation of various blade materials options in the context of more realistic representations of blade structure than do the standard test methods. Types of structural details addressed in this report include ply drops used in thickness tapering, and adhesive joints, each tested over a range of fatigue loading conditions. Ply drop studies were in two areas: (1) a combined experimental and finite element study of basic ply drop delamination parameters for glass and carbon prepreg laminates, and (2) the development of a complex structured resin-infused coupon including ply drops, for comparison studies of various resins, fabrics and pry drop thicknesses. Adhesive joint tests using typical blade adhesives included both generic testing of materials parameters using a notched-lap-shear test geometry developed in this study, and also a series of simulated blade web joint geometries fabricated by an industry partner.« less

The Evolving Role of Coliforms As Indicators of Unhygienic Processing Conditions in Dairy Foods.

PubMed

Martin, Nicole H; Trmčić, Aljoša; Hsieh, Tsung-Han; Boor, Kathryn J; Wiedmann, Martin

2016-01-01

Testing for coliforms has a long history in the dairy industry and has helped to identify raw milk and dairy products that may have been exposed to unsanitary conditions. Coliform standards are included in a number of regulatory documents (e.g., the U.S. Food and Drug Administration's Grade "A" Pasteurized Milk Ordinance). As a consequence, detection above a threshold of members of this method-defined, but diverse, group of bacteria can result in a wide range of regulatory outcomes. Coliforms are defined as aerobic or facultatively anaerobic, Gram negative, non-sporeforming rods capable of fermenting lactose to produce gas and acid within 48 h at 32-35°C; 19 genera currently include at least some strains that represent coliforms. Most bacterial genera that comprise the coliform group (e.g., Escherichia , Klebsiella , and Serratia ) are within the family Enterobacteriaceae, while at least one genus with strains recognized as coliforms, Aeromonas , is in the family Aeromonadaceae. The presence of coliforms has long been thought to indicate fecal contamination, however, recent discoveries regarding this diverse group of bacteria indicates that only a fraction are fecal in origin, while the majority are environmental contaminants. In the US dairy industry in particular, testing for coliforms as indicators of unsanitary conditions and post-processing contamination is widespread. While coliforms are easily and rapidly detected, and are not found in pasteurized dairy products that have not been exposed to post-processing contamination, advances in knowledge of bacterial populations most commonly associated with post-processing contamination in dairy foods has led to questions regarding the utility of coliforms as indicators of unsanitary conditions for dairy products. For example, Pseudomonas spp. frequently contaminate dairy products after pasteurization, yet they are not detected by coliform tests. This review will address the role that coliforms play in raw and finished dairy products, their sources and the future of this diverse group as indicator organisms in dairy products.

The Evolving Role of Coliforms As Indicators of Unhygienic Processing Conditions in Dairy Foods

PubMed Central

Martin, Nicole H.; Trmčić, Aljoša; Hsieh, Tsung-Han; Boor, Kathryn J.; Wiedmann, Martin

2016-01-01

Testing for coliforms has a long history in the dairy industry and has helped to identify raw milk and dairy products that may have been exposed to unsanitary conditions. Coliform standards are included in a number of regulatory documents (e.g., the U.S. Food and Drug Administration’s Grade “A” Pasteurized Milk Ordinance). As a consequence, detection above a threshold of members of this method-defined, but diverse, group of bacteria can result in a wide range of regulatory outcomes. Coliforms are defined as aerobic or facultatively anaerobic, Gram negative, non-sporeforming rods capable of fermenting lactose to produce gas and acid within 48 h at 32–35°C; 19 genera currently include at least some strains that represent coliforms. Most bacterial genera that comprise the coliform group (e.g., Escherichia, Klebsiella, and Serratia) are within the family Enterobacteriaceae, while at least one genus with strains recognized as coliforms, Aeromonas, is in the family Aeromonadaceae. The presence of coliforms has long been thought to indicate fecal contamination, however, recent discoveries regarding this diverse group of bacteria indicates that only a fraction are fecal in origin, while the majority are environmental contaminants. In the US dairy industry in particular, testing for coliforms as indicators of unsanitary conditions and post-processing contamination is widespread. While coliforms are easily and rapidly detected, and are not found in pasteurized dairy products that have not been exposed to post-processing contamination, advances in knowledge of bacterial populations most commonly associated with post-processing contamination in dairy foods has led to questions regarding the utility of coliforms as indicators of unsanitary conditions for dairy products. For example, Pseudomonas spp. frequently contaminate dairy products after pasteurization, yet they are not detected by coliform tests. This review will address the role that coliforms play in raw and finished dairy products, their sources and the future of this diverse group as indicator organisms in dairy products. PMID:27746769

Thermoplastic processing of proteins for film formation--a review.

PubMed

Hernandez-Izquierdo, V M; Krochta, J M

2008-03-01

Increasing interest in high-quality food products with increased shelf life and reduced environmental impact has encouraged the study and development of edible and/or biodegradable polymer films and coatings. Edible films provide the opportunity to effectively control mass transfer among different components in a food or between the food and its surrounding environment. The diversity of proteins that results from an almost limitless number of side-chain amino-acid sequential arrangements allows for a wide range of interactions and chemical reactions to take place as proteins denature and cross-link during heat processing. Proteins such as wheat gluten, corn zein, soy protein, myofibrillar proteins, and whey proteins have been successfully formed into films using thermoplastic processes such as compression molding and extrusion. Thermoplastic processing can result in a highly efficient manufacturing method with commercial potential for large-scale production of edible films due to the low moisture levels, high temperatures, and short times used. Addition of water, glycerol, sorbitol, sucrose, and other plasticizers allows the proteins to undergo the glass transition and facilitates deformation and processability without thermal degradation. Target film variables, important in predicting biopackage performance under various conditions, include mechanical, thermal, barrier, and microstructural properties. Comparisons of film properties should be made with care since results depend on parameters such as film-forming materials, film formulation, fabrication method, operating conditions, testing equipment, and testing conditions. Film applications include their use as wraps, pouches, bags, casings, and sachets to protect foods, reduce waste, and improve package recyclability.

Need for Cognition and False Memory: Can One's Natural Processing Style Be Manipulated by External Factors?

PubMed

Wootan, Samantha S; Leding, Juliana K

2015-01-01

The purpose of this experiment was to provide an enhanced understanding of need for cognition (NFC) and its influence on one's memory accuracy. People who are high in NFC tend to put more cognitive effort into their mental processes than their low-NFC counterparts. To determine whether one's natural processing tendencies, as determined by NFC, can be influenced by external factors, manipulations to levels of processing were added. Participants viewed word lists from the Deese-Roediger-McDermott (DRM) paradigm and were instructed to process half of the DRM lists deeply and the other half shallowly. After all the lists were presented, participants completed 3 successive recall tests. The deep processing condition produced higher rates of false memories for both NFC groups than the shallow processing condition. In addition, the high-NFC group produced higher rates of target recall in both the deep and shallow conditions than the low-NFC group. However, the high-NFC group also produced higher rates of false recall for the shallowly processed lists. These data indicate that high-NFC people exhibit enhanced target recall for word lists, which may come at the expense of overall accuracy due to the increase of false recall.

EUV mask manufacturing readiness in the merchant mask industry

NASA Astrophysics Data System (ADS)

Green, Michael; Choi, Yohan; Ham, Young; Kamberian, Henry; Progler, Chris; Tseng, Shih-En; Chiou, Tsann-Bim; Miyazaki, Junji; Lammers, Ad; Chen, Alek

2017-10-01

As nodes progress into the 7nm and below regime, extreme ultraviolet lithography (EUVL) becomes critical for all industry participants interested in remaining at the leading edge. One key cost driver for EUV in the supply chain is the reflective EUV mask. As of today, the relatively few end users of EUV consist primarily of integrated device manufactures (IDMs) and foundries that have internal (captive) mask manufacturing capability. At the same time, strong and early participation in EUV by the merchant mask industry should bring value to these chip makers, aiding the wide-scale adoption of EUV in the future. For this, merchants need access to high quality, representative test vehicles to develop and validate their own processes. This business circumstance provides the motivation for merchants to form Joint Development Partnerships (JDPs) with IDMs, foundries, Original Equipment Manufacturers (OEMs) and other members of the EUV supplier ecosystem that leverage complementary strengths. In this paper, we will show how, through a collaborative supplier JDP model between a merchant and OEM, a novel, test chip driven strategy is applied to guide and validate mask level process development. We demonstrate how an EUV test vehicle (TV) is generated for mask process characterization in advance of receiving chip maker-specific designs. We utilize the TV to carry out mask process "stress testing" to define process boundary conditions which can be used to create Mask Rule Check (MRC) rules as well as serve as baseline conditions for future process improvement. We utilize Advanced Mask Characterization (AMC) techniques to understand process capability on designs of varying complexity that include EUV OPC models with and without sub-resolution assist features (SRAFs). Through these collaborations, we demonstrate ways to develop EUV processes and reduce implementation risks for eventual mass production. By reducing these risks, we hope to expand access to EUV mask capability for the broadest community possible as the technology is implemented first within and then beyond the initial early adopters.

Landslide: Systematic Dynamic Race Detection in Kernel Space

DTIC Science & Technology

2012-05-01

schedule_in_flight← true; CAUSE_TIMER_INTERRUPT(); end if end function Thread Scheduling Finally, the Landslide scheduler is responsible for managing ...child process vanish() simultaneously. • double_wait: Tests interactions of multiple waiters on a single child. • double_thread_fork: Tests for...conditions using Landslide. We describe them here. • Too many waiters allowed. Using the double_wait test case, Group 1 found a bug in which more threads

Filter Media Tests Under Simulated Martian Atmospheric Conditions

NASA Technical Reports Server (NTRS)

Agui, Juan H.

2016-01-01

Human exploration of Mars will require the optimal utilization of planetary resources. One of its abundant resources is the Martian atmosphere that can be harvested through filtration and chemical processes that purify and separate it into its gaseous and elemental constituents. Effective filtration needs to be part of the suite of resource utilization technologies. A unique testing platform is being used which provides the relevant operational and instrumental capabilities to test articles under the proper simulated Martian conditions. A series of tests were conducted to assess the performance of filter media. Light sheet imaging of the particle flow provided a means of detecting and quantifying particle concentrations to determine capturing efficiencies. The media's efficiency was also evaluated by gravimetric means through a by-layer filter media configuration. These tests will help to establish techniques and methods for measuring capturing efficiency and arrestance of conventional fibrous filter media. This paper will describe initial test results on different filter media.

How Explicit and Implicit Test Instructions in an Implicit Learning Task Affect Performance

PubMed Central

Witt, Arnaud; Puspitawati, Ira; Vinter, Annie

2013-01-01

Typically developing children aged 5 to 8 years were exposed to artificial grammar learning. Following an implicit exposure phase, half of the participants received neutral instructions at test while the other half received instructions making a direct, explicit reference to the training phase. We first aimed to assess whether implicit learning operated in the two test conditions. We then evaluated the differential impact of age on learning performances as a function of test instructions. The results showed that performance did not vary as a function of age in the implicit instructions condition, while age effects emerged when explicit instructions were employed at test. However, performance was affected differently by age and the instructions given at test, depending on whether the implicit learning of short or long units was assessed. These results suggest that the claim that the implicit learning process is independent of age needs to be revised. PMID:23326409

Hot-crack test for aluminium alloys welds using TIG process

NASA Astrophysics Data System (ADS)

Niel, A.; Deschaux-Beaume, F.; Bordreuil, C.; Fras, G.

2010-06-01

Hot cracking is a critical defect frequently observed during welding of aluminium alloys. In order to better understand the interaction between cracking phenomenon, process parameters, mechanical factors and microstructures resulting from solidification after welding, an original hot-cracking test during welding is developed. According to in-situ observations and post mortem analyses, hot cracking mechanisms are investigated, taking into account the interaction between microstructural parameters, depending on the thermal cycles, and mechanical parameters, depending on geometry and clamping conditions of the samples and on the thermal field on the sample. Finally, a process map indicating the limit between cracking and non-cracking zones according to welding parameters is presented.

Functional outcomes assessment in shoulder surgery

PubMed Central

Wylie, James D; Beckmann, James T; Granger, Erin; Tashjian, Robert Z

2014-01-01

The effective evaluation and management of orthopaedic conditions including shoulder disorders relies upon understanding the level of disability created by the disease process. Validated outcome measures are critical to the evaluation process. Traditionally, outcome measures have been physician derived objective evaluations including range of motion and radiologic evaluations. However, these measures can marginalize a patient’s perception of their disability or outcome. As a result of these limitations, patient self-reported outcomes measures have become popular over the last quarter century and are currently primary tools to evaluate outcomes of treatment. Patient reported outcomes measures can be general health related quality of life measures, health utility measures, region specific health related quality of life measures or condition specific measures. Several patients self-reported outcomes measures have been developed and validated for evaluating patients with shoulder disorders. Computer adaptive testing will likely play an important role in the arsenal of measures used to evaluate shoulder patients in the future. The purpose of this article is to review the general health related quality-of-life measures as well as the joint-specific and condition specific measures utilized in evaluating patients with shoulder conditions. Advances in computer adaptive testing as it relates to assessing dysfunction in shoulder conditions will also be reviewed. PMID:25405091

Semantic and self-referential processing of positive and negative trait adjectives in older adults

PubMed Central

Glisky, Elizabeth L.; Marquine, Maria J.

2008-01-01

The beneficial effects of self-referential processing on memory have been demonstrated in numerous experiments with younger adults but have rarely been studied in older individuals. In the present study we tested young people, younger-older adults, and older-older adults in a self-reference paradigm, and compared self-referential processing to general semantic processing. Findings indicated that older adults over the age of 75 and those with below average episodic memory function showed a decreased benefit from both semantic and self-referential processing relative to a structural baseline condition. However, these effects appeared to be confined to the shared semantic processes for the two conditions, leaving the added advantage for self-referential processing unaffected These results suggest that reference to the self engages qualitatively different processes compared to general semantic processing. These processes seem relatively impervious to age and to declining memory and executive function, suggesting that they might provide a particularly useful way for older adults to improve their memories. PMID:18608973

Honeybees (Apis mellifera) Learn Color Discriminations via Differential Conditioning Independent of Long Wavelength (Green) Photoreceptor Modulation

PubMed Central

Wijesekara Witharanage, Randika; Rosa, Marcello G. P.

2012-01-01

Background Recent studies on colour discrimination suggest that experience is an important factor in how a visual system processes spectral signals. In insects it has been shown that differential conditioning is important for processing fine colour discriminations. However, the visual system of many insects, including the honeybee, has a complex set of neural pathways, in which input from the long wavelength sensitive (‘green’) photoreceptor may be processed either as an independent achromatic signal or as part of a trichromatic opponent-colour system. Thus, a potential confound of colour learning in insects is the possibility that modulation of the ‘green’ photoreceptor could underlie observations. Methodology/Principal Findings We tested honeybee vision using light emitting diodes centered on 414 and 424 nm wavelengths, which limit activation to the short-wavelength-sensitive (‘UV’) and medium-wavelength-sensitive (‘blue’) photoreceptors. The absolute irradiance spectra of stimuli was measured and modelled at both receptor and colour processing levels, and stimuli were then presented to the bees in a Y-maze at a large visual angle (26°), to ensure chromatic processing. Sixteen bees were trained over 50 trials, using either appetitive differential conditioning (N = 8), or aversive-appetitive differential conditioning (N = 8). In both cases the bees slowly learned to discriminate between the target and distractor with significantly better accuracy than would be expected by chance. Control experiments confirmed that changing stimulus intensity in transfers tests does not significantly affect bee performance, and it was possible to replicate previous findings that bees do not learn similar colour stimuli with absolute conditioning. Conclusion Our data indicate that honeybee colour vision can be tuned to relatively small spectral differences, independent of ‘green’ photoreceptor contrast and brightness cues. We thus show that colour vision is at least partly experience dependent, and behavioural plasticity plays an important role in how bees exploit colour information. PMID:23155394

Potential Use of BEST® Sediment Trap in Splash - Saltation Transport Process by Simultaneous Wind and Rain Tests

PubMed Central

Basaran, Mustafa; Uzun, Oguzhan; Cornelis, Wim; Gabriels, Donald; Erpul, Gunay

2016-01-01

The research on wind-driven rain (WDR) transport process of the splash-saltation has increased over the last twenty years as wind tunnel experimental studies provide new insights into the mechanisms of simultaneous wind and rain (WDR) transport. The present study was conducted to investigate the efficiency of the BEST® sediment traps in catching the sand particles transported through the splash-saltation process under WDR conditions. Experiments were conducted in a wind tunnel rainfall simulator facility with water sprayed through sprinkler nozzles and free-flowing wind at different velocities to simulate the WDR conditions. Not only for vertical sediment distribution, but a series of experimental tests for horizontal distribution of sediments was also performed using BEST® collectors to obtain the actual total sediment mass flow by the splash-saltation in the center of the wind tunnel test section. Total mass transport (kg m-2) were estimated by analytically integrating the exponential functional relationship using the measured sediment amounts at the set trap heights for every run. Results revealed the integrated efficiency of the BEST® traps at 6, 9, 12 and 15 m s-1 wind velocities under 55.8, 50.5, 55.0 and 50.5 mm h-1 rain intensities were, respectively, 83, 106, 105, and 102%. Results as well showed that the efficiencies of BEST® did not change much as compared with those under rainless wind condition. PMID:27898716

Advanced direct coal liquefaction concepts. Quarterly report, April 1, 1993--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

Construction and commissioning of the bench unit for operation of the first stage of the process was completed. Solubilization of Black Thunder coal using carbon monoxide and steam was successfully demonstrated in the counterflow reactor system. The results were comparable with those obtained in the autoclave with the exception that coal solubilization at the same nominal residence times was slightly lower. The bench unit has now been modified for two stage operation. The Wilsonville process derived solvent for Black Thunder coal (V-1074) was found to be essentially as stable as the previous solvent used in the autoclave runs (V-178 +more » 320) at reactor conditions. This solvent (V-1074) is, therefore, being used in the bench unit tests. Carbon monoxide may be replaced by synthesis gas for the coal solubilization step in the process. However, in autoclave tests, coal conversion was found to be dependent on the amount of carbon monoxide present in the synthesis gas. Coal conversions ranged from 88% for pure carbon monoxide to 67% for a 25:75 carbon monoxide/hydrogen mixture at equivalent conditions. Two stage liquefaction tests were completed in the autoclave using a disposable catalyst (FeS) and hydrogen in the second stage. Increased coal conversion, higher gas and oil and lower asphaltene and preasphaltene yields were observed as expected. However, no hydrogen consumption was observed in the second stage. Other conditions, in particular, alternate catalyst systems will be explored.« less

Crack identification and evolution law in the vibration failure process of loaded coal

NASA Astrophysics Data System (ADS)

Li, Chengwu; Ai, Dihao; Sun, Xiaoyuan; Xie, Beijing

2017-08-01

To study the characteristics of coal cracks produced in the vibration failure process, we set up a static load and static and dynamic combination load failure test simulation system, prepared with different particle size, formation pressure, and firmness coefficient coal samples. Through static load damage testing of coal samples and then dynamic load (vibration exciter) and static (jack) combination destructive testing, the crack images of coal samples under the load condition were obtained. Combined with digital image processing technology, an algorithm of crack identification with high precision and in real-time is proposed. With the crack features of the coal samples under different load conditions as the research object, we analyzed the distribution of cracks on the surface of the coal samples and the factors influencing crack evolution using the proposed algorithm and a high-resolution industrial camera. Experimental results showed that the major portion of the crack after excitation is located in the rear of the coal sample where the vibration exciter cannot act. Under the same disturbance conditions, crack size and particle size exhibit a positive correlation, while crack size and formation pressure exhibit a negative correlation. Soft coal is more likely to lead to crack evolution than hard coal, and more easily causes instability failure. The experimental results and crack identification algorithm provide a solid basis for the prevention and control of instability and failure of coal and rock mass, and they are helpful in improving the monitoring method of coal and rock dynamic disasters.

XV-15 Tiltrotor Aircraft: 1997 Acoustic Testing

NASA Technical Reports Server (NTRS)

Edwards, Bryan D.; Conner, David A.

2003-01-01

XV-15 acoustic test is discussed, and measured results are presented. The test was conducted by NASA Langley and Bell Helicopter Textron, Inc., during June - July 1997, at the BHTI test site near Waxahachie, Texas. This was the second in a series of three XV-15 tests to document the acoustic signature of the XV-15 tiltrotor aircraft for a variety of flight conditions and minimize the noise signature during approach. Tradeoffs between flight procedures and the measured noise are presented to illustrate the noise abatement flight procedures. The test objectives were to: (1) support operation of future tiltrotors by further developing and demonstrating low-noise flight profiles, while maintaining acceptable handling and ride qualities, and (2) refine approach profiles, selected from previous (1995) tiltrotor testing, to incorporate Instrument Flight Rules (IFR), handling qualities constraints, operations and tradeoffs with sound. Primary emphasis was given to the approach flight conditions where blade-vortex interaction (BVI) noise dominates, because this condition influences community noise impact more than any other. An understanding of this part of the noise generating process could guide the development of low noise flight operations and increase the tiltrotor's acceptance in the community.

Assessment of a condition-specific quality-of-life measure for patients with developmentally absent teeth: validity and reliability testing.

PubMed

Akram, A J; Ireland, A J; Postlethwaite, K C; Sandy, J R; Jerreat, A S

2013-11-01

This article describes the process of validity and reliability testing of a condition-specific quality-of-life measure for patients with hypodontia presenting for orthodontic treatment. The development of the instrument is described in a previous article. Royal Devon and Exeter NHS Foundation Trust & Musgrove Park Hospital, Taunton. The child perception questionnaire was used as a standard against which to test criterion validity. The Bland and Altman method was used to check agreement between the two questionnaires. Construct validity was tested using principal component analysis on the four sections of the questionnaire. Test-retest reliability was tested using intraclass correlation coefficient and Bland and Altman method. Cronbach's alpha was used to test internal consistency reliability. Overall the questionnaire showed good reliability, criterion and construct validity. This together with previous evidence of good face and content validity suggests that the instrument may prove useful in clinical practice and further research. This study has demonstrated that the newly developed condition-specific quality-of-life questionnaire is both valid and reliable for use in young patients with hypodontia. © 2013 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

Third-Order Spectral Techniques for the Diagnosis of Motor Bearing Condition Using Artificial Neural Networks

NASA Astrophysics Data System (ADS)

Yang, D.-M.; Stronach, A. F.; MacConnell, P.; Penman, J.

2002-03-01

This paper addresses the development of a novel condition monitoring procedure for rolling element bearings which involves a combination of signal processing, signal analysis and artificial intelligence methods. Seven approaches based on power spectrum, bispectral and bicoherence vibration analyses are investigated as signal pre-processing techniques for application in the diagnosis of a number of induction motor rolling element bearing conditions. The bearing conditions considered are a normal bearing and bearings with cage and inner and outer race faults. The vibration analysis methods investigated are based on the power spectrum, the bispectrum, the bicoherence, the bispectrum diagonal slice, the bicoherence diagonal slice, the summed bispectrum and the summed bicoherence. Selected features are extracted from the vibration signatures so obtained and these are used as inputs to an artificial neural network trained to identify the bearing conditions. Quadratic phase coupling (QPC), examined using the magnitude of bispectrum and bicoherence and biphase, is shown to be absent from the bearing system and it is therefore concluded that the structure of the bearing vibration signatures results from inter-modulation effects. In order to test the proposed procedure, experimental data from a bearing test rig are used to develop an example diagnostic system. Results show that the bearing conditions examined can be diagnosed with a high success rate, particularly when using the summed bispectrum signatures.

Advances in Thin Film Thermocouple Durability Under High Temperature and Pressure Testing Conditions

NASA Technical Reports Server (NTRS)

Martin, Lisa C.; Fralick, Gustave C.; Taylor, Keith F.

1999-01-01

Thin film thermocouples for measuring material surface temperature have been previously demonstrated on several material systems and in various hostile test environments. A well-developed thin film fabrication procedure utilizing shadow masking for patterning the sensors elements had produced thin films with sufficient durability for applications in high temperature and pressure environments that exist in air-breathing and hydrogen-fueled burner rig and engine test facilities. However, while shadow masking had been a reliable method for specimens with flat and gently curved surfaces, it had not been consistently reliable for use on test components with sharp contours. This work reports on the feasibility of utilizing photolithography processing for patterning thin film thermocouples. Because this patterning process required changes in the thin film deposition process from that developed for shadow masking, the effect of these changes on thin film adherence during burner rig testing was evaluated. In addition to the results of changing the patterning method, the effects on thin film adherence of other processes used in the thin film fabrication procedure is also presented.

Multi-crop area estimation and mapping on a microprocessor/mainframe network

NASA Technical Reports Server (NTRS)

Sheffner, E.

1985-01-01

The data processing system is outlined for a 1985 test aimed at determining the performance characteristics of area estimation and mapping procedures connected with the California Cooperative Remote Sensing Project. The project is a joint effort of the USDA Statistical Reporting Service-Remote Sensing Branch, the California Department of Water Resources, NASA-Ames Research Center, and the University of California Remote Sensing Research Program. One objective of the program was to study performance when data processing is done on a microprocessor/mainframe network under operational conditions. The 1985 test covered the hardware, software, and network specifications and the integration of these three components. Plans for the year - including planned completion of PEDITOR software, testing of software on MIDAS, and accomplishment of data processing on the MIDAS-VAX-CRAY network - are discussed briefly.

To Know or Not to Know? Integrating Ethical Aspects of Genomic Healthcare in the Education of Health Professionals

ERIC Educational Resources Information Center

Eriksen, Kathrine Krageskov

2015-01-01

Novel possibilities for employing genetic testing as part of the diagnostic process for a wide variety of diseases and conditions are emerging almost every day. This development brings prospects of more efficient treatment and prevention of serious and often lethal conditions. However, it also raises ethical questions concerning the issue of…

Ground Vehicle Condition Based Maintenance

DTIC Science & Technology

2010-10-04

Diagnostic Process Map 32 FMEAs Developed : • Diesel Engine • Transmission • Alternators Analysis : • Identify failure modes • Derive design factors and...S&T Initiatives  TARDEC P&D Process Map  Component Testing  ARL CBM Research  AMSAA SDC & Terrain Modeling UNCLASSIFIED 3 CBM+ Overview...UNCLASSIFIED 4 RCM and CBM are core processes for CBM+ System Development • Army Regulation 750-1, 20 Sep 2007, p. 79 - Reliability Centered Maintenance (RCM

Comparing fire spread algorithms using equivalence testing and neutral landscape models

Treesearch

Brian R. Miranda; Brian R. Sturtevant; Jian Yang; Eric J. Gustafson

2009-01-01

We demonstrate a method to evaluate the degree to which a meta-model approximates spatial disturbance processes represented by a more detailed model across a range of landscape conditions, using neutral landscapes and equivalence testing. We illustrate this approach by comparing burn patterns produced by a relatively simple fire spread algorithm with those generated by...

Filter Leaf. Operational Control Tests for Wastewater Treatment Facilities. Instructor's Manual [and] Student Workbook.

ERIC Educational Resources Information Center

Wooley, John F.

In the operation of vacuum filters and belt filters, it is desirable to evaluate the performance of different types of filter media and conditioning processes. The filter leaf test, which is used to evaluate these items, is described. Designed for individuals who have completed National Pollutant Discharge Elimination System (NPDES) level 1…

40 CFR 122.42 - Additional conditions applicable to specified categories of NPDES permits (applicable to State...

Code of Federal Regulations, 2014 CFR

2014-07-01

...; (vii) Identify protocols for appropriate testing of manure, litter, process wastewater, and soil; (viii... under roof (beef cattle, broilers, layers, swine weighing 55 pounds or more, swine weighing less than 55... paragraph (e)(5)(ii) of this section, the results of any soil testing for nitrogen and phosphorus taken...

40 CFR 122.42 - Additional conditions applicable to specified categories of NPDES permits (applicable to State...

Code of Federal Regulations, 2013 CFR

2013-07-01

...; (vii) Identify protocols for appropriate testing of manure, litter, process wastewater, and soil; (viii... under roof (beef cattle, broilers, layers, swine weighing 55 pounds or more, swine weighing less than 55... paragraph (e)(5)(ii) of this section, the results of any soil testing for nitrogen and phosphorus taken...

40 CFR 122.42 - Additional conditions applicable to specified categories of NPDES permits (applicable to State...

Code of Federal Regulations, 2012 CFR

2012-07-01

...; (vii) Identify protocols for appropriate testing of manure, litter, process wastewater, and soil; (viii... under roof (beef cattle, broilers, layers, swine weighing 55 pounds or more, swine weighing less than 55... paragraph (e)(5)(ii) of this section, the results of any soil testing for nitrogen and phosphorus taken...

The effect of encoding manipulation on word-stem cued recall: an event-related potential study.

PubMed

Fay, Séverine; Isingrini, Michel; Ragot, Richard; Pouthas, Viviane

2005-08-01

The purpose of the present study was to find out whether the neural correlates of explicit retrieval from episodic memory would vary according to conditions at encoding when the words were presented in separate study/test blocks. Event-related potentials (ERPs) were recorded while participants performed a word-stem cued-recall task. Deeply (semantically) studied words were associated with higher levels of recall and faster response times than shallowly (lexically) studied words. Robust ERP old/new effects were observed for each encoding condition. They varied in magnitude, being largest in the semantic condition. As expected, scalp distributions also differed: for deeply studied words, the old/new effect resembled that found in previous ERP studies of word-stem cued-recall tasks (parietal and right frontal effects, between 400-800 and 800-1100 ms post-stimulus), whereas for shallowly studied words, the parietal old/new effect was absent in the latter latency window. These results can be interpreted as reflecting access to different kinds of memory representation depending on the nature of the processing engaged during encoding. Furthermore, differences in the ERPs elicited by new items indicate that subjects adopted different processing strategies in the test blocks following each encoding condition.

Dynamic strain aging in stress controlled creep-fatigue tests of 316L stainless steel under different loading conditions

NASA Astrophysics Data System (ADS)

Jiang, Huifeng; Chen, Xuedong; Fan, Zhichao; Dong, Jie; Jiang, Heng; Lu, Shouxiang

2009-08-01

Stress controlled fatigue-creep tests were carried out for 316L stainless steel under different loading conditions, i.e. different loading levels at the fixed temperature (loading condition 1, LC1) and different temperatures at the fixed loading level (loading condition 2, LC2). Cyclic deformation behaviors were investigated with respect to the evolutions of strain amplitude and mean strain. Abrupt mean strain jumps were found during cyclic deformation, which was in response to the dynamic strain aging effect. Moreover, as to LC1, when the minimum stress is negative at 550 °C, abrupt mean strain jumps occur at the early stage of cyclic deformation and there are many jumps during the whole process. While the minimum stress is positive, mean strain only jumps once at the end of deformation. Similar results were also found in LC2, when the loading level is fixed at -100 to 385 MPa, at higher temperatures (560, 575 °C), abrupt mean strain jumps occur at the early stage of cyclic deformation and there are many jumps during the whole process. While at lower temperature (540 °C), mean strain only jumps once at the end of deformation.

Winery waste recycling through anaerobic co-digestion with waste activated sludge.

PubMed

Da Ros, C; Cavinato, C; Pavan, P; Bolzonella, D

2014-11-01

In this study biogas and high quality digestate were recovered from winery waste (wine lees) through anaerobic co-digestion with waste activated sludge both in mesophilic and thermophilic conditions. The two conditions studied showed similar yields (0.40 m(3)/kgCODfed) but different biological process stability: in fact the mesophilic process was clearly more stable than the thermophilic one in terms of bioprocess parameters. The resulting digestates showed good characteristics for both the tested conditions: heavy metals, dioxins (PCDD/F), and dioxin like bi-phenyls (PCBs) were concentred in the effluent if compared with the influent because of the important reduction of the solid dry matter, but remained at levels acceptable for agricultural reuse. Pathogens in digestate decreased. Best reductions were observed in thermophilic condition, while at 37°C the concentration of Escherichia coli was at concentrations level as high as 1000 UFC/g. Dewatering properties of digestates were evaluated by means of the capillary suction time (CST) and specific resistance to filtration (SRF) tests and it was found that a good dewatering level was achievable only when high doses of polymer (more than 25 g per kg dry solids) were added to sludge. Copyright © 2014 Elsevier Ltd. All rights reserved.

Discourse comprehension in L2: Making sense of what is not explicitly said.

PubMed

Foucart, Alice; Romero-Rivas, Carlos; Gort, Bernharda Lottie; Costa, Albert

2016-12-01

Using ERPs, we tested whether L2 speakers can integrate multiple sources of information (e.g., semantic, pragmatic information) during discourse comprehension. We presented native speakers and L2 speakers with three-sentence scenarios in which the final sentence was highly causally related, intermediately related, or causally unrelated to its context; its interpretation therefore required simple or complex inferences. Native speakers revealed a gradual N400-like effect, larger in the causally unrelated condition than in the highly related condition, and falling in-between in the intermediately related condition, replicating previous results. In the crucial intermediately related condition, L2 speakers behaved like native speakers, however, showing extra processing in a later time-window. Overall, the results show that, when reading, L2 speakers are able to process information from the local context and prior information (e.g., world knowledge) to build global coherence, suggesting that they process different sources of information to make inferences online during discourse comprehension, like native speakers. Copyright © 2016 Elsevier Inc. All rights reserved.

Flight Test Implementation of a Second Generation Intelligent Flight Control System

NASA Technical Reports Server (NTRS)

Williams-Hayes, Peggy S.

2005-01-01

The NASA F-15 Intelligent Flight Control System project team has developed a series of flight control concepts designed to demonstrate the benefits of a neural network-based adaptive controller. The objective of the team was to develop and flight-test control systems that use neural network technology, to optimize the performance of the aircraft under nominal conditions, and to stabilize the aircraft under failure conditions. Failure conditions include locked or failed control surfaces as well as unforeseen damage that might occur to the aircraft in flight. The Intelligent Flight Control System team is currently in the process of implementing a second generation control scheme, collectively known as Generation 2 or Gen 2, for flight testing on the NASA F-15 aircraft. This report describes the Gen 2 system as implemented by the team for flight test evaluation. Simulation results are shown which describe the experiment to be performed in flight and highlight the ways in which the Gen 2 system meets the defined objectives.

Combustion of LOX with H2(sub g) under subcritical, critical, and supercritical conditions (Task 1) and experimental observation of dense spray and mixing of impinging jets (Task 2)

NASA Technical Reports Server (NTRS)

Kuo, K. K.; Hsieh, W. H.; Cheung, F. B.; Yang, A. S.; Brown, J. J.; Woodward, R. D.; Kline, M. C.; Burch, R. L.

1992-01-01

The objective was to achieve a better understanding of the combustion processes of liquid oxygen and gaseous hydrogen under broad range of pressure covering subcritical, critical, and supercritical conditions. The scope of the experimental work falls into the following areas: (1) design of the overall experimental setup; (2) modification of an existing windowed high pressure chamber; (3) design of the LOX feeding system; (4) provision of the safety features in the test rig design; (5) LOX cleanliness requirements; (6) cold shock testing; (7) implementation of data acquisition systems; (8) preliminary tests for system checkout; (9) modification of LOX feeding system; and (10) evaporation tests. Progress in each area is discussed.

Performance of Adsorption - Based CO2 Acquisition Hardware for Mars ISRU

NASA Technical Reports Server (NTRS)

Finn, John E.; Mulloth, Lila M.; Borchers, Bruce A.; Luna, Bernadette (Technical Monitor)

2000-01-01

Chemical processing of the dusty, low-pressure Martian atmosphere typically requires conditioning and compression of the gases as first steps. A temperature-swing adsorption process can perform these tasks using nearly solid-state hardware and with relatively low power consumption compared to alternative processes. In addition, the process can separate the atmospheric constituents, producing both pressurized CO2 and a buffer gas mixture of nitrogen and argon. To date we have developed and tested adsorption compressors at scales appropriate for the near-term robotic missions that will lead the way to ISRU-based human exploration missions. In this talk we describe the characteristics, testing, and performance of these devices. We also discuss scale-up issues associated with meeting the processing demands of sample return and human missions.

Post-trial apomorphine at an autoreceptor dose level can eliminate apomorphine conditioning and sensitization: support for the critical role of dopamine in re-consolidation.

PubMed

Carrera, Marinete Pinheiro; Carey, Robert J; Cruz Dias, Flávia Regina; dos Santos Sampaio, Maria de Fátima; de Matos, Liana Wermelinger

2013-01-01

Re-exposure to conditioned drug stimuli triggers re-consolidation processes. In the present study post-trial apomorphine treatments were administered in order to interact with the re-consolidation of an apomorphine conditioned/sensitized locomotor response. A low (0.05 mg/kg) and a high (2.0mg/kg) dose were used to inhibit or to enhance dopamine activity, respectively. Initially, groups received 5 daily apomorphine (2.0mg/kg)/vehicle treatments either paired or unpaired to open-field placement. The paired treatments generated a progressive locomotor response. Subsequently, all groups received a 5 min non-drug test for conditioning and a conditioned locomotor response was observed in the paired group. The groups received another apomorphine (2.0mg/kg)/vehicle treatment as a re-induction treatment. At this stage the post-trial protocol was initiated. One set of paired, unpaired and vehicle groups were given a low dose of apomorphine (0.05 mg/kg) post-trial; another set received a high dose of apomorphine (2.0mg/kg) post-trial. The remaining group set received vehicle post-trial. The low dose post-trial treatment eliminated the conditioned and sensitized locomotor response and the high dose post-trial treatment enhanced the conditioned and sensitized locomotor response. The efficacy of the post-trial apomorphine treatments to modify the conditioned and the sensitized response after a brief non-drug exposure to test cues supports the proposition that exteroceptive cues control conditioning and sensitization and that the interoceptive drug cues make little or no associational contribution to apomorphine conditioning and sensitization. In addition, the findings point to the importance of dopamine activation in both the acquisition and re-consolidation of conditioning processes. Copyright © 2012 Elsevier B.V. All rights reserved.

Developmental differences in the impact of contextual factors on susceptibility to retroactive interference.

PubMed

Levy-Gigi, Einat; Vakil, Eli

2010-01-01

The influence of contextual similarity on children's recognition memory performance was examined using a retroactive interference paradigm. In the study, 9- and 12-year-olds were randomly assigned to one of two contextual conditions. In both conditions, target and interfering information were presented in distinctive contexts by using different modalities (pictures and words, respectively). However, in one condition the test was presented in the same context as the target information (picture-word-picture [PWP] condition), whereas in the other condition the test was presented in the same context as the interfering information (picture-word-word [PWW] condition). Performance in these conditions was compared with performance in a noninterference control condition (picture-word [P-W]). As predicted, overall recognition performance in the PWP condition was significantly better than in the PWW condition. However, whereas in the PWP condition there was no age difference in performance, in the PWW condition the 12-year-old group produced significantly more hits and fewer false alarms than the 9-year-old group. The theoretical implications of the results are discussed in reference to the effortful engagement of developmentally dependent executive control processes.

Literature review for oxalate oxidation processes and plutonium oxalate solubility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nash, C. A.

2015-10-01

A literature review of oxalate oxidation processes finds that manganese(II)-catalyzed nitric acid oxidation of oxalate in precipitate filtrate is a viable and well-documented process. The process has been operated on the large scale at Savannah River in the past, including oxidation of 20 tons of oxalic acid in F-Canyon. Research data under a variety of conditions show the process to be robust. This process is recommended for oxalate destruction in H-Canyon in the upcoming program to produce feed for the MOX facility. Prevention of plutonium oxalate precipitation in filtrate can be achieved by concentrated nitric acid/ferric nitrate sequestration of oxalate.more » Organic complexants do not appear practical to sequester plutonium. Testing is proposed to confirm the literature and calculation findings of this review at projected operating conditions for the upcoming campaign.« less

Development of a Process for a High Capacity Arc Heater Production of Silicon for Solar Arrays

NASA Technical Reports Server (NTRS)

Reed, W. H.

1979-01-01

A program was established to develop a high temperature silicon production process using existing electric arc heater technology. Silicon tetrachloride and a reductant (sodium) are injected into an arc heated mixture of hydrogen and argon. Under these high temperature conditions, a very rapid reaction is expected to occur and proceed essentially to completion, yielding silicon and gaseous sodium chloride. Techniques for high temperature separation and collection were developed. Included in this report are: test system preparation; testing; injection techniques; kinetics; reaction demonstration; conclusions; and the project status.

Nickel-hydrogen capacity loss on storage

NASA Technical Reports Server (NTRS)

Manzo, Michelle A.

1989-01-01

A controlled experiment evaluating the capacity loss experienced by nickel electrodes stored under various conditions of temperature, hydrogen pressure, and electrolyte concentration was conducted using nickel electrodes from four different manufacturers. It was found that capacity loss varied with respect to hydrogen pressure, and storage temperature as well as with respect to electrode manufacturing processes. Impedance characteristics were monitored and found to be indicative of electrode manufacturing processes and capacity loss. Cell testing to evaluate state-of-charge effects on capacity loss were inconclusive as no loss was sustained by the cells tested in this experiment.

Manufacturing stresses and strains in filament wound cylinders

NASA Technical Reports Server (NTRS)

Calius, E. P.; Kidron, M.; Lee, S. Y.; Springer, G. S.

1988-01-01

Tests were performed to verify a previously developed model for simulating the manufacturing process of filament wound cylinders. The axial and hoop strains were measured during cure inside a filament wound Fiberite T300/976 graphite-epoxy cylinder. The measured strains were compared to those computed by the model. Good agreements were found between the data and the model, indicating that the model is a useful representation of the process. For the conditions of the test, the manufacturing stresses inside the cylinder were also calculated using the model.

Preliminary evaluation of feeder and lint slide moisture addition on ginning, fiber quality, and textile processing of western cotton

USDA-ARS?s Scientific Manuscript database

The objective of this study was to evaluate the effects of moisture addition at the gin stand feeder conditioning hopper and/or the battery condenser slide on gin performance and Western cotton fiber quality and textile processing. The test treatments included no moisture addition, feeder hopper hum...

Analysis of the structural behaviour of colonic segments by inflation tests: Experimental activity and physio-mechanical model.

PubMed

Carniel, Emanuele L; Mencattelli, Margherita; Bonsignori, Gabriella; Fontanella, Chiara G; Frigo, Alessandro; Rubini, Alessandro; Stefanini, Cesare; Natali, Arturo N

2015-11-01

A coupled experimental and computational approach is provided for the identification of the structural behaviour of gastrointestinal regions, accounting for both elastic and visco-elastic properties. The developed procedure is applied to characterize the mechanics of gastrointestinal samples from pig colons. Experimental data about the structural behaviour of colonic segments are provided by inflation tests. Different inflation processes are performed according to progressively increasing top pressure conditions. Each inflation test consists of an air in-flow, according to an almost constant increasing pressure rate, such as 3.5 mmHg/s, up to a prescribed top pressure, which is held constant for about 300 s to allow the development of creep phenomena. Different tests are interspersed by 600 s of rest to allow the recovery of the tissues' mechanical condition. Data from structural tests are post-processed by a physio-mechanical model in order to identify the mechanical parameters that interpret both the non-linear elastic behaviour of the sample, as the instantaneous pressure-stretch trend, and the time-dependent response, as the stretch increase during the creep processes. The parameters are identified by minimizing the discrepancy between experimental and model results. Different sets of parameters are evaluated for different specimens from different pigs. A statistical analysis is performed to evaluate the distribution of the parameters and to assess the reliability of the experimental and computational activities. © IMechE 2015.

Soil Moisture Processes in the Near Surface Unsaturated Zone: Experimental Investigations in Multi-scale Test Systems

NASA Astrophysics Data System (ADS)

Illangasekare, T. H.; Sakaki, T.; Smits, K. M.; Limsuwat, A.; Terrés-Nícoli, J. M.

2008-12-01

Understanding the dynamics of soil moisture distribution near the ground surface is of interest in various applications involving land-atmospheric interaction, evaporation from soils, CO2 leakage from carbon sequestration, vapor intrusion into buildings, and land mine detection. Natural soil heterogeneity in combination with water and energy fluxes at the soil surface creates complex spatial and temporal distributions of soil moisture. Even though considerable knowledge exists on how soil moisture conditions change in response to flux and energy boundary conditions, emerging problems involving land atmospheric interactions require the quantification of soil moisture variability both at high spatial and temporal resolutions. The issue of up-scaling becomes critical in all applications, as in general, field measurements are taken at sparsely distributed spatial locations that require assimilation with measurements taken using remote sensing technologies. It is our contention that the knowledge that will contribute to both improving our understanding of the fundamental processes and practical problem solution cannot be obtained easily in the field due to a number of constraints. One of these basic constraints is the inability to make measurements at very fine spatial scales at high temporal resolutions in naturally heterogeneous field systems. Also, as the natural boundary conditions at the land/atmospheric interface are not controllable in the field, even in pilot scale studies, the developed theories and tools cannot be validated for the diversity of conditions that could be expected in the field. Intermediate scale testing using soil tanks packed to represent different heterogeneous test configurations provides an attractive and cost effective alternative to investigate a class of problems involving the shallow unsaturated zone. In this presentation, we will discuss the advantages and limitations of studies conducted in both two and three dimensional intermediate scale test systems together with instrumentation and measuring techniques. The features and capabilities of a new coupled porous media/climate wind tunnel test system that allows for the study of near surface unsaturated soil moisture conditions under climate boundary conditions will also be presented with the goal of exploring opportunities to use such a facility to study some of the multi-scale problems in the near surface unsaturated zone.

Assessing technical performance at diverse ambulatory care sites.

PubMed

Osterweis, M; Bryant, E

1978-01-01

The purpose of the large study reported here was to develop and test methods for assessing the quality of health care that would be broadly applicable to diverse ambulatory care organizations for periodic comparative review. Methodological features included the use of an age-sex stratified random sampling scheme, dependence on medical records as the source of data, a fixed study period year, use of Kessner's tracer methodology (including not only acute and chronic diseases but also screening and immunization rates as indicators), and a fixed tracer matrix at all test sites. This combination of methods proved more efficacious in estimating certain parameters for the total patient populations at each site (including utilization patterns, screening, and immunization rates) and the process of care for acute conditions than it did in examining the process of care for the selected chronic condition. It was found that the actual process of care at all three sites for the three acute conditions (streptococcal pharyngitis, urinary tract infection, and iron deficiency anemia) often differed from the expected process in terms of both diagnostic procedures and treatment. For hypertension, the chronic disease tracer, medical records were frequently a deficient data source from which to draw conclusions about the adequacy of treatment. Several aspects of the study methodology were found to be detrimental to between-site comparisons of the process of care for chronic disease management. The use of an age-sex stratified random sampling scheme resulted in the identification of too few cases of hypertension at some sites for analytic purposes, thereby necessitating supplementary sampling by diagnosis. The use of a fixed study period year resulted in an arbitrary starting point in the course of the disease. Furthermore, in light of the diverse sociodemographic characteristics of the patient populations, the use of a fixed matrix of tracer conditions for all test sites is questionable. The discussion centers on these and other problems encountered in attempting to compare technical performance within diverse ambulatory care organizations and provides some guidelines as to the utility of alternative methods for assessing the quality of health care.

To plan or not to plan: Does planning for production remove facilitation from associative priming?

PubMed

Jongman, Suzanne R; Meyer, Antje S

2017-11-01

Theories of conversation propose that in order to have smooth transitions from one turn to the next, speakers already plan their response while listening to their interlocutor. Moreover, it has been argued that speakers align their linguistic representations (i.e. prime each other), thereby reducing the processing costs associated with concurrent listening and speaking. In two experiments, we assessed how identity and associative priming from spoken words onto picture naming were affected by a concurrent speech planning task. In a baseline (no name) condition, participants heard prime words that were identical, associatively related, or unrelated to target pictures presented two seconds after prime onset. Each prime was accompanied by a non-target picture and followed by its recorded name. The participant did not name the non-target picture. In the plan condition, the participants first named the non-target picture, instead of listening to the recording, and then the target. In Experiment 1, where the plan- and no-plan conditions were tested between participants, priming effects of equal strength were found in the plan and no-plan condition. In Experiment 2, where the two conditions were tested within participants, the identity priming effect was maintained, but the associative priming effect was only seen in the no-plan but not in the plan condition. In this experiment, participant had to decide at the onset of each trial whether or not to name the non-target picture, rendering the task more complex than in Experiment 1. These decision processes may have interfered with the processing of the primes. Thus, associative priming can take place during speech planning, but only if the cognitive load is not too high. Copyright © 2017 Elsevier B.V. All rights reserved.

The role of attention during encoding in implicit and explicit memory.

PubMed

Mulligan, N W

1998-01-01

In 5 experiments, participants read study words under conditions of divided or full attention. Dividing attention reduced performance on the general knowledge test, a conceptual implicit test of memory. Likewise, dividing attention reduced conceptual priming on the word--association task, as well as on a matched explicit test, associate-cued recall. In contrast, even very strong division of attention did not reduce perceptual priming on word-fragment completion, although it did reduce recall on the matched explicit test of word-fragment-cued recall. Finally, dividing attention reduced recall on the perceptual explicit tests of graphemic-cued recall and graphemic recognition. The results indicate that perceptual implicit tests rely minimally on attention-demanding encoding processes relative to other types of memory tests. The obtained pattern of dissociations is not readily accommodated by the transfer-appropriate-processing (TAP) account of implicit and explicit memory. Potential extensions of the TAP view are discussed.

A powerful and robust test in genetic association studies.

PubMed

Cheng, Kuang-Fu; Lee, Jen-Yu

2014-01-01

There are several well-known single SNP tests presented in the literature for detecting gene-disease association signals. Having in place an efficient and robust testing process across all genetic models would allow a more comprehensive approach to analysis. Although some studies have shown that it is possible to construct such a test when the variants are common and the genetic model satisfies certain conditions, the model conditions are too restrictive and in general difficult to verify. In this paper, we propose a powerful and robust test without assuming any model restrictions. Our test is based on the selected 2 × 2 tables derived from the usual 2 × 3 table. By signals from these tables, we show through simulations across a wide range of allele frequencies and genetic models that this approach may produce a test which is almost uniformly most powerful in the analysis of low- and high-frequency variants. Two cancer studies are used to demonstrate applications of the proposed test. © 2014 S. Karger AG, Basel.

Mechanical Design of a Performance Test Rig for the Turbine Air-Flow Task (TAFT)

NASA Technical Reports Server (NTRS)

Xenofos, George; Forbes, John; Farrow, John; Williams, Robert; Tyler, Tom; Sargent, Scott; Moharos, Jozsef

2003-01-01

To support development of the Boeing-Rocketdyne RS84 rocket engine, a fill-flow, reaction turbine geometry was integrated into the NASA-MSFC turbine air-flow test facility. A mechanical design was generated which minimized the amount of new hardware while incorporating all test and instrUmentation requirements. This paper provides details of the mechanical design for this Turbine Air-Flow Task (TAFT) test rig. The mechanical design process utilized for this task included the following basic stages: Conceptual Design. Preliminary Design. Detailed Design. Baseline of Design (including Configuration Control and Drawing Revision). Fabrication. Assembly. During the design process, many lessons were learned that should benefit future test rig design projects. Of primary importance are well-defined requirements early in the design process, a thorough detailed design package, and effective communication with both the customer and the fabrication contractors. The test rig provided steady and unsteady pressure data necessary to validate the computational fluid dynamics (CFD) code. The rig also helped characterize the turbine blade loading conditions. Test and CFD analysis results are to be presented in another JANNAF paper.

Speech Intelligibility in Various Noise Conditions with the Nucleus® 5 CP810 Sound Processor.

PubMed

Dillier, Norbert; Lai, Wai Kong

2015-06-11

The Nucleus(®) 5 System Sound Processor (CP810, Cochlear™, Macquarie University, NSW, Australia) contains two omnidirectional microphones. They can be configured as a fixed directional microphone combination (called Zoom) or as an adaptive beamformer (called Beam), which adjusts the directivity continuously to maximally reduce the interfering noise. Initial evaluation studies with the CP810 had compared performance and usability of the new processor in comparison with the Freedom™ Sound Processor (Cochlear™) for speech in quiet and noise for a subset of the processing options. This study compares the two processing options suggested to be used in noisy environments, Zoom and Beam, for various sound field conditions using a standardized speech in noise matrix test (Oldenburg sentences test). Nine German-speaking subjects who previously had been using the Freedom speech processor and subsequently were upgraded to the CP810 device participated in this series of additional evaluation tests. The speech reception threshold (SRT for 50% speech intelligibility in noise) was determined using sentences presented via loudspeaker at 65 dB SPL in front of the listener and noise presented either via the same loudspeaker (S0N0) or at 90 degrees at either the ear with the sound processor (S0NCI+) or the opposite unaided ear (S0NCI-). The fourth noise condition consisted of three uncorrelated noise sources placed at 90, 180 and 270 degrees. The noise level was adjusted through an adaptive procedure to yield a signal to noise ratio where 50% of the words in the sentences were correctly understood. In spatially separated speech and noise conditions both Zoom and Beam could improve the SRT significantly. For single noise sources, either ipsilateral or contralateral to the cochlear implant sound processor, average improvements with Beam of 12.9 and 7.9 dB in SRT were found. The average SRT of -8 dB for Beam in the diffuse noise condition (uncorrelated noise from both sides and back) is truly remarkable and comparable to the performance of normal hearing listeners in the same test environment. The static directivity (Zoom) option in the diffuse noise condition still provides a significant benefit of 5.9 dB in comparison with the standard omnidirectional microphone setting. These results indicate that CI recipients may improve their speech recognition in noisy environments significantly using these directional microphone-processing options.

Spontaneous Recovery But Not Reinstatement of the Extinguished Conditioned Eyeblink Response in the Rat

PubMed Central

Thanellou, Alexandra; Green, John T.

2011-01-01

Reinstatement, the return of an extinguished conditioned response (CR) after reexposure to the unconditioned stimulus (US), and spontaneous recovery, the return of an extinguished CR with the passage of time, are two of four well-established phenomena which demonstrate that extinction does not erase the conditioned stimulus (CS)-US association. However, reinstatement of extinguished eyeblink CRs has never been demonstrated and spontaneous recovery of extinguished eyeblink CRs has not been systematically demonstrated in rodent eyeblink conditioning. In Experiment 1, US reexposure was administered 24 hours prior to a reinstatement test. In Experiment 2, US reexposure was administered 5 min prior to a reinstatement test. In Experiment 3, a long, discrete cue (a houselight), present in all phases of training and testing, served as a context within which each trial occurred to maximize context processing, which in other preparations has been shown to be required for reinstatement. In Experiment 4, an additional group was included that received footshock exposure, rather than US reexposure, between extinction and test, and contextual freezing was measured prior to test. Spontaneous recovery was robust in Experiments 3 and 4. In Experiment 4, context freezing was strong in a group given footshock exposure but not in a group given eyeshock US reexposure. There was no reinstatement observed in any experiment. With stimulus conditions that produce eyeblink conditioning and research designs that produce reinstatement in other forms of classical conditioning, we observed spontaneous recovery but not reinstatement of extinguished eyeblink CRs. This suggests that reinstatement, but not spontaneous recovery, is a preparation- or substrate-dependent phenomenon. PMID:21517145

Effects of Long-Term Ayahuasca Administration on Memory and Anxiety in Rats

PubMed Central

Favaro, Vanessa Manchim; Yonamine, Maurício; Soares, Juliana Carlota Kramer; Oliveira, Maria Gabriela Menezes

2015-01-01

Ayahuasca is a hallucinogenic beverage that combines the action of the 5-HT2A/2C agonist N,N-dimethyltryptamine (DMT) from Psychotria viridis with the monoamine oxidase inhibitors (MAOIs) induced by beta-carbonyls from Banisteriopsis caapi. Previous investigations have highlighted the involvement of ayahuasca with the activation of brain regions known to be involved with episodic memory, contextual associations and emotional processing after ayahuasca ingestion. Moreover long term users show better performance in neuropsychological tests when tested in off-drug condition. This study evaluated the effects of long-term administration of ayahuasca on Morris water maze (MWM), fear conditioning and elevated plus maze (EPM) performance in rats. Behavior tests started 48h after the end of treatment. Freeze-dried ayahuasca doses of 120, 240 and 480 mg/kg were used, with water as the control. Long-term administration consisted of a daily oral dose for 30 days by gavage. The behavioral data indicated that long-term ayahuasca administration did not affect the performance of animals in MWM and EPM tasks. However the dose of 120 mg/kg increased the contextual conditioned fear response for both background and foreground fear conditioning. The tone conditioned response was not affected after long-term administration. In addition, the increase in the contextual fear response was maintained during the repeated sessions several weeks after training. Taken together, these data showed that long-term ayahuasca administration in rats can interfere with the contextual association of emotional events, which is in agreement with the fact that the beverage activates brain areas related to these processes. PMID:26716991

Effects of Long-Term Ayahuasca Administration on Memory and Anxiety in Rats.

PubMed

Favaro, Vanessa Manchim; Yonamine, Maurício; Soares, Juliana Carlota Kramer; Oliveira, Maria Gabriela Menezes

2015-01-01

Ayahuasca is a hallucinogenic beverage that combines the action of the 5-HT2A/2C agonist N,N-dimethyltryptamine (DMT) from Psychotria viridis with the monoamine oxidase inhibitors (MAOIs) induced by beta-carbonyls from Banisteriopsis caapi. Previous investigations have highlighted the involvement of ayahuasca with the activation of brain regions known to be involved with episodic memory, contextual associations and emotional processing after ayahuasca ingestion. Moreover long term users show better performance in neuropsychological tests when tested in off-drug condition. This study evaluated the effects of long-term administration of ayahuasca on Morris water maze (MWM), fear conditioning and elevated plus maze (EPM) performance in rats. Behavior tests started 48h after the end of treatment. Freeze-dried ayahuasca doses of 120, 240 and 480 mg/kg were used, with water as the control. Long-term administration consisted of a daily oral dose for 30 days by gavage. The behavioral data indicated that long-term ayahuasca administration did not affect the performance of animals in MWM and EPM tasks. However the dose of 120 mg/kg increased the contextual conditioned fear response for both background and foreground fear conditioning. The tone conditioned response was not affected after long-term administration. In addition, the increase in the contextual fear response was maintained during the repeated sessions several weeks after training. Taken together, these data showed that long-term ayahuasca administration in rats can interfere with the contextual association of emotional events, which is in agreement with the fact that the beverage activates brain areas related to these processes.

Case Comparisons: An Efficient Way of Learning Radiology.

PubMed

Kok, Ellen M; de Bruin, Anique B H; Leppink, Jimmie; van Merriënboer, Jeroen J G; Robben, Simon G F

2015-10-01

Radiologists commonly use comparison films to improve their differential diagnosis. Educational literature suggests that this technique might also be used to bolster the process of learning to interpret radiographs. We investigated the effectiveness of three comparison techniques in medical students, whom we invited to compare cases of the same disease (same-disease comparison), cases of different diseases (different-disease comparison), disease images with normal images (disease/normal comparison), and identical images (no comparison/control condition). Furthermore, we used eye-tracking technology to investigate which elements of the two cases were compared by the students. We randomly assigned 84 medical students to one of four conditions and had them study different diseases on chest radiographs, while their eye movements were being measured. Thereafter, participants took two tests that measured diagnostic performance and their ability to locate diseases, respectively. Students studied most efficiently in the same-disease and different-disease comparison conditions: test 1, F(3, 68) = 3.31, P = .025, ηp(2) = 0.128; test 2, F(3, 65) = 2.88, P = .043, ηp(2) = 0.117. We found that comparisons were effected in 91% of all trials (except for the control condition). Comparisons between normal anatomy were particularly common (45.8%) in all conditions. Comparing cases can be an efficient way of learning to interpret radiographs, especially when the comparison technique used is specifically tailored to the learning goal. Eye tracking provided insight into the comparison process, by showing that few comparisons were made between abnormalities, for example. Copyright © 2015 AUR. Published by Elsevier Inc. All rights reserved.

Solidified structure and leaching properties of metallurgical wastewater treatment sludge after solidification/stabilization process.

PubMed

Radovanović, Dragana Đ; Kamberović, Željko J; Korać, Marija S; Rogan, Jelena R

2016-01-01

The presented study investigates solidification/stabilization process of hazardous heavy metals/arsenic sludge, generated after the treatment of the wastewater from a primary copper smelter. Fly ash and fly ash with addition of hydrated lime and Portland composite cement were studied as potential binders. The effectiveness of the process was evaluated by unconfined compressive strength (UCS) testing, leaching tests (EN 12457-4 and TCLP) and acid neutralization capacity (ANC) test. It was found that introduction of cement into the systems increased the UCS, led to reduced leaching of Cu, Ni and Zn, but had a negative effect on the ANC. Gradual addition of lime resulted in decreased UCS, significant reduction of metals leaching and high ANC, due to the excess of lime that remained unreacted in pozzolanic reaction. Stabilization of more than 99% of heavy metals and 90% of arsenic has been achieved. All the samples had UCS above required value for safe disposal. In addition to standard leaching tests, solidificates were exposed to atmospheric conditions during one year in order to determine the actual leaching level of metals in real environment. It can be concluded that the EN 12457-4 test is more similar to the real environmental conditions, while the TCLP test highly exaggerates the leaching of metals. The paper also presents results of differential acid neutralization (d-AN) analysis compared with mineralogical study done by scanning electron microscopy and X-ray diffraction analysis. The d-AN coupled with Eh-pH (Pourbaix) diagrams were proven to be a new effective method for analysis of amorphous solidified structure.

Points to consider for prioritizing clinical genetic testing services: a European consensus process oriented at accountability for reasonableness

PubMed Central

Severin, Franziska; Borry, Pascal; Cornel, Martina C; Daniels, Norman; Fellmann, Florence; Victoria Hodgson, Shirley; Howard, Heidi C; John, Jürgen; Kääriäinen, Helena; Kayserili, Hülya; Kent, Alastair; Koerber, Florian; Kristoffersson, Ulf; Kroese, Mark; Lewis, Celine; Marckmann, Georg; Meyer, Peter; Pfeufer, Arne; Schmidtke, Jörg; Skirton, Heather; Tranebjærg, Lisbeth; Rogowski, Wolf H

2015-01-01

Given the cost constraints of the European health-care systems, criteria are needed to decide which genetic services to fund from the public budgets, if not all can be covered. To ensure that high-priority services are available equitably within and across the European countries, a shared set of prioritization criteria would be desirable. A decision process following the accountability for reasonableness framework was undertaken, including a multidisciplinary EuroGentest/PPPC-ESHG workshop to develop shared prioritization criteria. Resources are currently too limited to fund all the beneficial genetic testing services available in the next decade. Ethically and economically reflected prioritization criteria are needed. Prioritization should be based on considerations of medical benefit, health need and costs. Medical benefit includes evidence of benefit in terms of clinical benefit, benefit of information for important life decisions, benefit for other people apart from the person tested and the patient-specific likelihood of being affected by the condition tested for. It may be subject to a finite time window. Health need includes the severity of the condition tested for and its progression at the time of testing. Further discussion and better evidence is needed before clearly defined recommendations can be made or a prioritization algorithm proposed. To our knowledge, this is the first time a clinical society has initiated a decision process about health-care prioritization on a European level, following the principles of accountability for reasonableness. We provide points to consider to stimulate this debate across the EU and to serve as a reference for improving patient management. PMID:25248395

Points to consider for prioritizing clinical genetic testing services: a European consensus process oriented at accountability for reasonableness.

PubMed

Severin, Franziska; Borry, Pascal; Cornel, Martina C; Daniels, Norman; Fellmann, Florence; Victoria Hodgson, Shirley; Howard, Heidi C; John, Jürgen; Kääriäinen, Helena; Kayserili, Hülya; Kent, Alastair; Koerber, Florian; Kristoffersson, Ulf; Kroese, Mark; Lewis, Celine; Marckmann, Georg; Meyer, Peter; Pfeufer, Arne; Schmidtke, Jörg; Skirton, Heather; Tranebjærg, Lisbeth; Rogowski, Wolf H

2015-06-01

Given the cost constraints of the European health-care systems, criteria are needed to decide which genetic services to fund from the public budgets, if not all can be covered. To ensure that high-priority services are available equitably within and across the European countries, a shared set of prioritization criteria would be desirable. A decision process following the accountability for reasonableness framework was undertaken, including a multidisciplinary EuroGentest/PPPC-ESHG workshop to develop shared prioritization criteria. Resources are currently too limited to fund all the beneficial genetic testing services available in the next decade. Ethically and economically reflected prioritization criteria are needed. Prioritization should be based on considerations of medical benefit, health need and costs. Medical benefit includes evidence of benefit in terms of clinical benefit, benefit of information for important life decisions, benefit for other people apart from the person tested and the patient-specific likelihood of being affected by the condition tested for. It may be subject to a finite time window. Health need includes the severity of the condition tested for and its progression at the time of testing. Further discussion and better evidence is needed before clearly defined recommendations can be made or a prioritization algorithm proposed. To our knowledge, this is the first time a clinical society has initiated a decision process about health-care prioritization on a European level, following the principles of accountability for reasonableness. We provide points to consider to stimulate this debate across the EU and to serve as a reference for improving patient management.

A Materials Compatibility and Thermal Stability Analysis of Common Hydrocarbon Fuels

NASA Technical Reports Server (NTRS)

Meyer, M. L.; Stiegemeier, B. R.

2005-01-01

A materials compatibility and thermal stability investigation was conducted using five common liquid hydrocarbon fuels and two structural materials. The tests were performed at the NASA Glenn Research Center Heated Tube Facility under environmental conditions similar to those encountered in regeneratively cooled rocket engines. Scanning-electron microscopic analysis in conjunction with energy dispersive spectroscopy (EDS) was utilized to characterize the condition of the tube inner wall surface and any carbon deposition or corrosion that was formed during selected runs. Results show that the carbon deposition process in stainless steel tubes was relatively insensitive to fuel type or test condition. The deposition rates were comparable for all fuels and none of the stainless steel test pieces showed any signs of corrosion. For tests conducted with copper tubing, the sulfur content of the fuel had a significant impact on both the condition of the tube wall and carbon deposition rates. Carbon deposition rates for the lowest sulfur fuels (2 ppm) were slightly higher than those recorded in the stainless steel tubes with no corrosion observed on the inner wall surface. For slightly higher sulfur content (25 ppm) fuels, nodules that intruded into the flow area were observed to form on the inner wall surface. These nodules induced moderate tube pressure drop increases. The highest sulfur content fuels (400 ppm) produced extensive wall pitting and dendritic copper sulfide growth that was continuous along the entire tube wall surface. The result of this tube degradation was the inability to maintain flow rate due to rapidly increasing test section pressure drops. Accompanying this corrosion were carbon deposition rates an order of magnitude greater than those observed in comparable stainless steel tests. The results of this investigation indicate that trace impurities in fuels (i.e. sulfur) can significantly impact the carbon deposition process and produce unacceptable corrosion levels in copper based structural materials.

Short-term total sleep deprivation alters delay-conditioned memory in the rat.

PubMed

Tripathi, Shweta; Jha, Sushil K

2016-06-01

Short-term sleep deprivation soon after training may impair memory consolidation. Also, a particular sleep stage or its components increase after learning some tasks, such as negative and positive reinforcement tasks, avoidance tasks, and spatial learning tasks, and so forth. It suggests that discrete memory types may require specific sleep stage or its components for their optimal processing. The classical conditioning paradigms are widely used to study learning and memory but the role of sleep in a complex conditioned learning is unclear. Here, we have investigated the effects of short-term sleep deprivation on the consolidation of delay-conditioned memory and the changes in sleep architecture after conditioning. Rats were trained for the delay-conditioned task (for conditioning, house-light [conditioned stimulus] was paired with fruit juice [unconditioned stimulus]). Animals were divided into 3 groups: (a) sleep deprived (SD); (b) nonsleep deprived (NSD); and (c) stress control (SC) groups. Two-way ANOVA revealed a significant interaction between groups and days (training and testing) during the conditioned stimulus-unconditioned stimulus presentation. Further, Tukey post hoc comparison revealed that the NSD and SC animals exhibited significant increase in performances during testing. The SD animals, however, performed significantly less during testing. Further, we observed that wakefulness and NREM sleep did not change after training and testing. Interestingly, REM sleep increased significantly on both days compared to baseline more specifically during the initial 4-hr time window after conditioning. Our results suggest that the consolidation of delay-conditioned memory is sleep-dependent and requires augmented REM sleep during an explicit time window soon after training. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

The Study and Application of Hydrometallurgical Gold Leaching in the Analysis of Refractory Precious Metals

NASA Astrophysics Data System (ADS)

Yang, M.; Geng, X.; Wang, Y. L.; Li, D. X.

2017-05-01

Three orthogonal tests are separately designed for each hydrometallurgical gold leaching process to finding the optimum reaction conditions of melting gold and palladium in each process. Under the optimum condition, the determination amount of gold and palladium in aqua regia—hydrofluoric acid, Sodium thiosulfate, and potassium iodide reaches 2.87g/kg and 8.34 g/kg, 2.39g/kg and 8.12 g/kg, 2.51g/kg and 7.84g/kg. From the result, the content of gold and palladium using the leaching process of combining Aqua regia, hydrofluoric acid and hydrogen peroxide is relatively higher than the other processes. In addition, the experiment procedure of aqua regia digestion operates easily, using less equipment, and its period is short.

Shelf life extension for the lot AAE nozzle severance LSCs

NASA Technical Reports Server (NTRS)

Cook, M.

1990-01-01

Shelf life extension tests for the remaining lot AAE linear shaped charges for redesigned solid rocket motor nozzle aft exit cone severance were completed in the small motor conditioning and firing bay, T-11. Five linear shaped charge test articles were thermally conditioned and detonated, demonstrating proper end-to-end charge propagation. Penetration depth requirements were exceeded. Results indicate that there was no degradation in performance due to aging or the linear shaped charge curving process. It is recommended that the shelf life of the lot AAE nozzle severance linear shaped charges be extended through January 1992.

Forward conditioning with wheel running causes place aversion in rats.

PubMed

Masaki, Takahisa; Nakajima, Sadahiko

2008-09-01

Backward pairings of a distinctive chamber as a conditioned stimulus and wheel running as an unconditioned stimulus (i.e., running-then-chamber) can produce a conditioned place preference in rats. The present study explored whether a forward conditioning procedure with these stimuli (i.e., chamber-then-running) would yield place preference or aversion. Confinement of a rat in one of two distinctive chambers was followed by a 20- or 60-min running opportunity, but confinement in the other was not. After four repetitions of this treatment (i.e., differential conditioning), a choice preference test was given in which the rat had free access to both chambers. This choice test showed that the rats given 60-min running opportunities spent less time in the running-paired chamber than in the unpaired chamber. Namely, a 60-min running opportunity after confinement in a distinctive chamber caused conditioned aversion to that chamber after four paired trials. This result was discussed with regard to the opponent-process theory of motivation.

Emotional Involvement as a Factor in the Learning Process

ERIC Educational Resources Information Center

Mumpower, D. L.

1973-01-01

Sexual items on a pre-post vocabulary test of little known words in college level abnormal psychology produced the greatest evidence of learning; word associations and no aid'' conditions were used in comparison. (Editor)

Laser ignition of a multi-injector LOX/methane combustor

NASA Astrophysics Data System (ADS)

Börner, Michael; Manfletti, Chiara; Hardi, Justin; Suslov, Dmitry; Kroupa, Gerhard; Oschwald, Michael

2018-06-01

This paper reports the results of a test campaign of a laser-ignited combustion chamber with 15 shear coaxial injectors for the propellant combination LOX/methane. 259 ignition tests were performed for sea-level conditions. The igniter based on a monolithic ceramic laser system was directly attached to the combustion chamber and delivered 20 pulses with individual pulse energies of {33.2 ± 0.8 mJ } at 1064 nm wavelength and 2.3 ns FWHM pulse length. The applicability, reliability, and reusability of this ignition technology are demonstrated and the associated challenges during the start-up process induced by the oxygen two-phase flow are formulated. The ignition quality and pressure dynamics are evaluated using 14 dynamic pressure sensors distributed both azimuthally and axially along the combustion chamber wall. The influence of test sequencing on the ignition process is briefly discussed and the relevance of the injection timing of the propellants for the ignition process is described. The flame anchoring and stabilization process, as monitored using an optical probe system close to the injector faceplate connected to photomultiplier elements, is presented. For some of the ignition tests, non-uniform anchoring was detected with no influence onto the anchoring at steady-state conditions. The non-uniform anchoring can be explained by the inhomogeneous, transient injection of the two-phase flow of oxygen across the faceplate. This characteristic is verified by liquid nitrogen cold flow tests that were recorded by high-speed imaging. We conclude that by adapting the ignition sequence, laser ignition by optical breakdown of the propellants within the shear layer of a coaxial shear injector is a reliable ignition technology for LOX/methane combustors without significant over-pressure levels.

Laser ignition of a multi-injector LOX/methane combustor

NASA Astrophysics Data System (ADS)

Börner, Michael; Manfletti, Chiara; Hardi, Justin; Suslov, Dmitry; Kroupa, Gerhard; Oschwald, Michael

2018-02-01

This paper reports the results of a test campaign of a laser-ignited combustion chamber with 15 shear coaxial injectors for the propellant combination LOX/methane. 259 ignition tests were performed for sea-level conditions. The igniter based on a monolithic ceramic laser system was directly attached to the combustion chamber and delivered 20 pulses with individual pulse energies of {33.2 ± 0.8 mJ } at 1064 nm wavelength and 2.3 ns FWHM pulse length. The applicability, reliability, and reusability of this ignition technology are demonstrated and the associated challenges during the start-up process induced by the oxygen two-phase flow are formulated. The ignition quality and pressure dynamics are evaluated using 14 dynamic pressure sensors distributed both azimuthally and axially along the combustion chamber wall. The influence of test sequencing on the ignition process is briefly discussed and the relevance of the injection timing of the propellants for the ignition process is described. The flame anchoring and stabilization process, as monitored using an optical probe system close to the injector faceplate connected to photomultiplier elements, is presented. For some of the ignition tests, non-uniform anchoring was detected with no influence onto the anchoring at steady-state conditions. The non-uniform anchoring can be explained by the inhomogeneous, transient injection of the two-phase flow of oxygen across the faceplate. This characteristic is verified by liquid nitrogen cold flow tests that were recorded by high-speed imaging. We conclude that by adapting the ignition sequence, laser ignition by optical breakdown of the propellants within the shear layer of a coaxial shear injector is a reliable ignition technology for LOX/methane combustors without significant over-pressure levels.

Levels-of-processing effects on a task of olfactory naming.

PubMed

Royet, Jean-Pierre; Koenig, Olivier; Paugam-Moisy, Helene; Puzenat, Didier; Chasse, Jean-Luc

2004-02-01

The effects of odor processing were investigated at various analytical levels, from simple sensory analysis to deep or semantic analysis, on a subsequent task of odor naming. Students (106 women, 23.6 +/- 5.5 yr. old; 65 men, 25.1 +/- 7.1 yr. old) were tested. The experimental procedure included two successive sessions, a first session to characterize a set of 30 odors with criteria that used various depths of processing and a second session to name the odors as quickly as possible. Four processing conditions rated the odors using descriptors before naming the odor. The control condition did not rate the odors before naming. The processing conditions were based on lower-level olfactory judgments (superficial processing), higher-level olfactory-gustatory-somesthetic judgments (deep processing), and higher-level nonolfactory judgments (Deep-Control processing, with subjects rating odors with auditory and visual descriptors). One experimental condition successively grouped lower- and higher-level olfactory judgments (Superficial-Deep processing). A naming index which depended on response accuracy and the subjects' response time were calculated. Odor naming was modified for 18 out of 30 odorants as a function of the level of processing required. For 94.5% of significant variations, the scores for odor naming were higher following those tasks for which it was hypothesized that the necessary olfactory processing was carried out at a deeper level. Performance in the naming task was progressively improved as follows: no rating of odors, then superficial, deep-control, deep, and superficial-deep processings. These data show that the deepest olfactory encoding was later associated with progressively higher performance in naming.

Dry syngas purification process for coal gas produced in oxy-fuel type integrated gasification combined cycle power generation with carbon dioxide capturing feature.

PubMed

Kobayashi, Makoto; Akiho, Hiroyuki

2017-12-01

Electricity production from coal fuel with minimizing efficiency penalty for the carbon dioxide abatement will bring us sustainable and compatible energy utilization. One of the promising options is oxy-fuel type Integrated Gasification Combined Cycle (oxy-fuel IGCC) power generation that is estimated to achieve thermal efficiency of 44% at lower heating value (LHV) base and provide compressed carbon dioxide (CO 2 ) with concentration of 93 vol%. The proper operation of the plant is established by introducing dry syngas cleaning processes to control halide and sulfur compounds satisfying tolerate contaminants level of gas turbine. To realize the dry process, the bench scale test facility was planned to demonstrate the first-ever halide and sulfur removal with fixed bed reactor using actual syngas from O 2 -CO 2 blown gasifier for the oxy-fuel IGCC power generation. Design parameter for the test facility was required for the candidate sorbents for halide removal and sulfur removal. Breakthrough test was performed on two kinds of halide sorbents at accelerated condition and on honeycomb desulfurization sorbent at varied space velocity condition. The results for the both sorbents for halide and sulfur exhibited sufficient removal within the satisfactory short depth of sorbent bed, as well as superior bed conversion of the impurity removal reaction. These performance evaluation of the candidate sorbents of halide and sulfur removal provided rational and affordable design parameters for the bench scale test facility to demonstrate the dry syngas cleaning process for oxy-fuel IGCC system as the scaled up step of process development. Copyright © 2017 Elsevier Ltd. All rights reserved.

How does creating a concept map affect item-specific encoding?

PubMed

Grimaldi, Phillip J; Poston, Laurel; Karpicke, Jeffrey D

2015-07-01

Concept mapping has become a popular learning tool. However, the processes underlying the task are poorly understood. In the present study, we examined the effect of creating a concept map on the processing of item-specific information. In 2 experiments, subjects learned categorized or ad hoc word lists by making pleasantness ratings, sorting words into categories, or creating a concept map. Memory was tested using a free recall test and a recognition memory test, which is considered to be especially sensitive to item-specific processing. Typically, tasks that promote item-specific processing enhance free recall of categorized lists, relative to category sorting. Concept mapping resulted in lower recall performance than both the pleasantness rating and category sorting condition for categorized words. Moreover, concept mapping resulted in lower recognition memory performance than the other 2 tasks. These results converge on the conclusion that creating a concept map disrupts the processing of item-specific information. (c) 2015 APA, all rights reserved.

Aquifer recharge with reclaimed water in the Llobregat Delta. Laboratory batch experiments and field test site.

NASA Astrophysics Data System (ADS)

Tobella, J.

2010-05-01

Summary Spain, as most other Mediterranean countries, faces near future water shortages, generalized pollution and loss of water dependent ecosystems. Aquifer recharge represents a promising option to become a source for indirect potable reuse purposes but presence of pathogens as well as organic and inorganic pollutants should be avoided. To this end, understanding the processes of biogeochemical degradation occurring within the aquifer during infiltration is capital. A set of laboratory batch experiments has been assembled in order to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. Data collected during laboratory experiments and monitoring activities at the Sant Vicenç dels Horts test site will be used to build and calibrate a numerical model (i) of the physical-chemical-biochemical processes occurring in the batches and (ii) of multicomponent reactive transport in the unsaturated/saturated zone at the test site. Keywords Aquifer recharge, batch experiments, emerging micropollutants, infiltration, numerical model, reclaimed water, redox conditions, Soil Aquifer Treatment (SAT). 1. Introduction In Spain, the Llobregat River and aquifers, which supply water to Barcelona, have been overexploited for years and therefore, suffer from serious damages: the river dries up on summer, riparian vegetation has disappeared and seawater has intruded the aquifer. In a global context, solutions to water stress problems are urgently needed yet must be sustainable, economical and safe. Recent developments of analytical techniques detect the presence of the so-called "emerging" organic micropollutants in water and soils. Such compounds may affect living organisms when occurring in the environment at very low concentrations (microg/l or ng/l). In wastewater and drinking water treatment plants, a remarkable removal of these chemicals from water can be obtained only using advanced and costly treatments. Nevertheless, a number of studies are demonstrating that physical, chemical and biochemical processes associated with water movement within the subsoil represent a natural alternative way to reduce the presence of these contaminants. This processes are called Soil Aquifer Treatment (SAT). Aquifer recharge will become a source for indirect potable reuse purposes as long as the presence of pathogens and organic and inorganic pollutants is avoided. To this end, understanding the biogeochemical degradation processes occurring within the aquifer during infiltration is capital. 2. Laboratory batch experiments A set of laboratory batch experiments has been assembled to assess the behaviour of selected pesticides, drugs, estrogens, surfactant degradation products, biocides and phthalates under different redox conditions. The setup of the experiments consists of glass bottles containing 120 g of soil and 240 ml of synthetic water spiked with the mix of micropollutants. A source of easily degradable organic carbon and, depending on the type of test, electron acceptors are added in order to yield aerobic respiration and nitrate/iron/manganese/sulphate reduction conditions. The evolution of the processes is monitored by sacrificing duplicate bottles according to a defined schedule and analysing water for major and minor components as well as for micropollutants. Results from biotic tests are compared with abiotic ones in order to discern biodegradation from other chemical processes. The soil, the synthetic water and the micropollutants selected for the experiments are representative of a test site in the nearby of Barcelona (Spain) where artificial recharge of groundwater through ponds is going to be performed using river water or tertiary effluent from a waste water treatment plant. The results of the experiments improve the knowledge on the behaviour of the selected micropollutants under different redox conditions and provide with useful information on the conditions to develop at the test site during artificial recharge. The data collected during the laboratory experiments and in the test site will be used to build and calibrate a numerical model of the physical-chemical-biochemical processes developing in the batches and of multicomponent reactive transport in the unsaturated/saturated zone in the test site area. 3. Field test site The infiltration site of Sant Vicenç dels Horts has been selected to assessing the biogeochemical processes occurring during SAT. The system consists of two ponds that have been built as compensatory measure for the reduction in natural recharge caused by the construction of the High Speed Train Line. The first pond acts as a decantation pond while the second one acts as an infiltration basin (Figure 1). Recharge water comes from the tertiary treatment plant of the El Prat de Llobregat WWTP and the river (?). The CUADLL (Lower Llobregat Aquifer End-Users Community) is now managing the system operation. Tasks that are currently being carried out at this Test Site aims at (i) improving the local experience on MAR through infiltration ponds operational aspects and (ii) monitoring the changes in water quality during the recharge processes (unsaturated and saturated zone). Special attention is being paid to the fate of emerging organic pollutants (pharmaceuticals, surfactants, pesticides, etc.). The yielding of the monitoring will be compared with the results from the laboratory batch experiments on the behaviour of selected emerging organic pollutants. To this end, observation wells have been constructed, pressure / temperature / electrical conductivity transducers have been installed and the vadose zone under the infiltration pond has been instrumented (tensiometers, water content probes and suction cups). In addition double ring and infiltration tests have been performed in order to forecast the infiltration capacity of the basin.

Oculomotor Reflexes as a Test of Visual Dysfunctions in Cognitively Impaired Observers

DTIC Science & Technology

2013-09-01

right. Gaze horizontal position is plotted along the y-axis. The red bar indicates a visual nystagmus event detected by the filter. (d) A mild curse word...experimental conditions were chosen to simulate testing cognitively impaired observers. Reflex Stimulus Functions Visual Nystagmus luminance grating low-level...developed a new stimulus for visual nystagmus to 8 test visual motion processing in the presence of incoherent motion noise. The drifting equiluminant

Consolidation of an extinction memory depends on the unconditioned stimulus magnitude previously experienced during training.

PubMed

Stollhoff, Nicola; Eisenhardt, Dorothea

2009-07-29

Here, we examine the role of the magnitude of the unconditioned stimulus (US) during classical conditioning in consolidation processes after memory retrieval. We varied the US durations during training and we test the impact of these variations on consolidation after memory retrieval with one or two conditioned stimulus-only trials. We found that the consolidation of an extinction memory depends on US duration during training and ruled out the possibility that this effect is attributable to differences in satiation after conditioning. We conclude that consolidation of an extinction memory is triggered only when the duration of the US reaches a critical threshold. This demonstrates that memory consolidation cannot be regarded as an isolated process depending solely on training conditions. Instead, it depends on the animal's previous experience as well.

Color-specific conditioning effects due to both orange and blue stimuli are observed in a Halobacterium salinarum strain devoid of putative methylatable sites on HtrI.

PubMed

Lucia, S; Cercignani, G; Frediani, A; Petracchi, D

2003-01-01

Behavioral responses of Halobacterium salinarum appear as changes in the frequency of motion reversals. Turning on orange light decreases the reversal frequency, whereas blue light induces reversals. Light pulses normally induce the same response as step-up stimuli. However, anomalous behavioral reactions, including inverse responses, are seen when stimuli are applied in sequence. The occurrence of a prior stimulus is conditioning for successive stimulation on a time scale of the same order of adaptational processes. These prolonged conditioning effects are color-specific. The only adaptation process identified so far is methylation of the transducers, and this could be somehow color-specific. Therefore we tested for the behavioral anomalies in a mutant in which all methylation sites on the transducer have been eliminated. The results show that behavioral anomalies are unaffected by the absence of methylation processes on the transducer.

Material condition assessment with eddy current sensors

NASA Technical Reports Server (NTRS)

Goldfine, Neil J. (Inventor); Washabaugh, Andrew P. (Inventor); Sheiretov, Yanko K. (Inventor); Schlicker, Darrell E. (Inventor); Lyons, Robert J. (Inventor); Windoloski, Mark D. (Inventor); Craven, Christopher A. (Inventor); Tsukernik, Vladimir B. (Inventor); Grundy, David C. (Inventor)

2010-01-01

Eddy current sensors and sensor arrays are used for process quality and material condition assessment of conducting materials. In an embodiment, changes in spatially registered high resolution images taken before and after cold work processing reflect the quality of the process, such as intensity and coverage. These images also permit the suppression or removal of local outlier variations. Anisotropy in a material property, such as magnetic permeability or electrical conductivity, can be intentionally introduced and used to assess material condition resulting from an operation, such as a cold work or heat treatment. The anisotropy is determined by sensors that provide directional property measurements. The sensor directionality arises from constructs that use a linear conducting drive segment to impose the magnetic field in a test material. Maintaining the orientation of this drive segment, and associated sense elements, relative to a material edge provides enhanced sensitivity for crack detection at edges.

Pilot trial on separation conditions for diaper recycling.

PubMed

Kim, Kyung-Shin; Cho, Hee-Sun

2017-09-01

By utilizing laboratory-scale tests, the optimal separation conditions for diaper recycling were identified, and then, these conditions were validated by a pilot trial. In this research, we determined the mass balances derived during various processing steps and identified the most feasible procedures to use for separating each material in the output flow. The results showed that drum screening was not able to remove all the fiber and super absorbent particles (SAP) in the plastic-rich fraction and that cellulose enzyme treatment can be a good solution. To achieve better separation of fibers and SAP, slot screening followed by a cleaner is a potential option. A feasible diaper recycling process was recommended based on these results. This process involves screening and enzymatic treatment for the plastic fraction, and screening, cleaning, and thickening for the fiber fraction. Treatment procedures were also proposed for the SAP fraction and rejected materials. Copyright © 2017. Published by Elsevier Ltd.

Physics-based, Bayesian sequential detection method and system for radioactive contraband

DOEpatents

Candy, James V; Axelrod, Michael C; Breitfeller, Eric F; Chambers, David H; Guidry, Brian L; Manatt, Douglas R; Meyer, Alan W; Sale, Kenneth E

2014-03-18

A distributed sequential method and system for detecting and identifying radioactive contraband from highly uncertain (noisy) low-count, radionuclide measurements, i.e. an event mode sequence (EMS), using a statistical approach based on Bayesian inference and physics-model-based signal processing based on the representation of a radionuclide as a monoenergetic decomposition of monoenergetic sources. For a given photon event of the EMS, the appropriate monoenergy processing channel is determined using a confidence interval condition-based discriminator for the energy amplitude and interarrival time and parameter estimates are used to update a measured probability density function estimate for a target radionuclide. A sequential likelihood ratio test is then used to determine one of two threshold conditions signifying that the EMS is either identified as the target radionuclide or not, and if not, then repeating the process for the next sequential photon event of the EMS until one of the two threshold conditions is satisfied.

Routine Testing of Bitumen Binders

NASA Astrophysics Data System (ADS)

Holý, Michal; Remišová, Eva

2017-12-01

The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the "traditional" tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

Development and Validation of a Questionnaire to Assess Multimorbidity in Primary Care: An Indian Experience.

PubMed

Pati, Sanghamitra; Hussain, Mohammad Akhtar; Swain, Subhashisa; Salisbury, Chris; Metsemakers, Job F M; Knottnerus, J André; van den Akker, Marjan

2016-01-01

Multimorbidity remains an underexplored domain in Indian primary care. We undertook a study to assess the prevalence, correlates, and outcomes of multimorbidity in primary care settings in India. This paper describes the process of development and validation of our data collection tool "Multimorbidity Assessment Questionnaire for Primary Care (MAQ-PC)." An iterative process comprising desk review, chart review, and expert consultations was undertaken to generate the questionnaire. The MAQ-PC contained items on chronic conditions, health care utilization, health related quality of life, disease severity, and sociodemographics. It was first tested with twelve adults for comprehensibility followed by test-retest reliability with 103 patients from four primary care practices. For interrater reliability, two interviewers separately administered the questionnaire to sixteen patients. MAQ-PC displayed strong internal consistency (Cronbach's alpha: 0.69), interrater reliability (Cohen's Kappa: 0.78-1), and test-retest reliability (ICC: 0.970-0.741). Substantial concordance between self-report and physician diagnosis (Scott Kappa: 0.59-1.0) was observed for listed chronic conditions indicating strong concurrent validity. Nearly 54% had one chronic condition and 23.3% had multimorbidity. Our findings demonstrate MAQ-PC to be a valid and reliable measure of multimorbidity in primary care practice and suggest its potential utility in multimorbidity research in India.

Contribution of transcranial magnetic stimulation to assessment of brain connectivity and networks.

PubMed

Hallett, Mark; Di Iorio, Riccardo; Rossini, Paolo Maria; Park, Jung E; Chen, Robert; Celnik, Pablo; Strafella, Antonio P; Matsumoto, Hideyuki; Ugawa, Yoshikazu

2017-11-01

The goal of this review is to show how transcranial magnetic stimulation (TMS) techniques can make a contribution to the study of brain networks. Brain networks are fundamental in understanding how the brain operates. Effects on remote areas can be directly observed or identified after a period of stimulation, and each section of this review will discuss one method. EEG analyzed following TMS is called TMS-evoked potentials (TEPs). A conditioning TMS can influence the effect of a test TMS given over the motor cortex. A disynaptic connection can be tested also by assessing the effect of a pre-conditioning stimulus on the conditioning-test pair. Basal ganglia-cortical relationships can be assessed using electrodes placed in the process of deep brain stimulation therapy. Cerebellar-cortical relationships can be determined using TMS over the cerebellum. Remote effects of TMS on the brain can be found as well using neuroimaging, including both positron emission tomography (PET) and functional magnetic resonance imaging (fMRI). The methods complement each other since they give different views of brain networks, and it is often valuable to use more than one technique to achieve converging evidence. The final product of this type of work is to show how information is processed and transmitted in the brain. Published by Elsevier B.V.

Evolutionary perspectives on learning: conceptual and methodological issues in the study of adaptive specializations.

PubMed

Krause, Mark A

2015-07-01

Inquiry into evolutionary adaptations has flourished since the modern synthesis of evolutionary biology. Comparative methods, genetic techniques, and various experimental and modeling approaches are used to test adaptive hypotheses. In psychology, the concept of adaptation is broadly applied and is central to comparative psychology and cognition. The concept of an adaptive specialization of learning is a proposed account for exceptions to general learning processes, as seen in studies of Pavlovian conditioning of taste aversions, sexual responses, and fear. The evidence generally consists of selective associations forming between biologically relevant conditioned and unconditioned stimuli, with conditioned responses differing in magnitude, persistence, or other measures relative to non-biologically relevant stimuli. Selective associations for biologically relevant stimuli may suggest adaptive specializations of learning, but do not necessarily confirm adaptive hypotheses as conceived of in evolutionary biology. Exceptions to general learning processes do not necessarily default to an adaptive specialization explanation, even if experimental results "make biological sense". This paper examines the degree to which hypotheses of adaptive specializations of learning in sexual and fear response systems have been tested using methodologies developed in evolutionary biology (e.g., comparative methods, quantitative and molecular genetics, survival experiments). A broader aim is to offer perspectives from evolutionary biology for testing adaptive hypotheses in psychological science.

Assessment of working conditions in a modern Russian milk processing plant from the aspect of occupational medicine.

PubMed

Belova, L V; Mishkich, I A; Kresova, G A; Liubomudrova, T A

1999-03-01

Assessment of harmful industrial factors caused by work conditions in a modern milk processing plant. Work conditions, rest, nutrition, medical service, and subjective health indices among the employees in a new milk processing plant were studied. We used a specially formed questionnaire; instrumental measurements of microclimate parameters, noise, and illumination at workplace; laboratory physical and chemical evaluation of air pollution with aerosols and gases in the plant premises; chronometric studies determining the workers' activity during the working day location, and physical and psychological body exertion at the time of industrial activities; and assessment of design and operating documents of the plant. Laboratory studies included 157 workers, 1,724 tests, 26 chronometric studies, and analysis of 11 plant's documents. Unfavorable microclimatic conditions, noise, inadequate illumination, air pollution with dust and toxic substances, physical workload, increased demand for concentration, and monotony of labor in mass production professions were found. A great proportion of workers was dissatisfied with their working conditions and many suffered from occupational diseases and work-related diseases. The conditions of work in the studied milk processing plant may be classified as harmful and dangerous. The flaws in technological process, omissions in design and construction of the plant, as well as its improper exploitation aggravated industrial harmful factors. In combination with unsatisfactory organization of rest, nutrition, and medical services in the plant these factors may affect the workers' health and cause general and occupational diseases.

Time-dependent effects of prazosin on the development of methamphetamine conditioned hyperactivity and context-specific sensitization in mice.

PubMed

White, André O; Rauhut, Anthony S

2014-04-15

The present experiments examined the effects of prazosin, a selective α₁-adrenergic receptor antagonist, on the development of methamphetamine conditioned hyperactivity and context-specific sensitization. Mice received an injection of vehicle (distilled water) or prazosin (0.5, 1.0 or 2.0 mg/kg) 30 min prior to a second injection of vehicle (saline) or methamphetamine (1.0 mg/kg) during the conditioning sessions (Experiment 1). Following the conditioning sessions, mice were tested for conditioned hyperactivity and then tested for context-specific sensitization. In subsequent experiments, mice received an injection of vehicle (distilled water) or prazosin (2.0 mg/kg) immediately (Experiment 2) or 24 h (Experiment 3) after the conditioning sessions and then tested for conditioned hyperactivity and context-specific sensitization. Prazosin dose-dependently blocked the development of methamphetamine conditioned hyperactivity and context-specific sensitization when administered prior to the methamphetamine during the conditioning phase; however nonspecific motor impairments also were observed (Experiment 1). Immediate (Experiment 2), but not the 24-h delay (Experiment 3), post-session administration of prazosin attenuated the development of methamphetamine conditioned hyperactivity and context-specific sensitization. Nonspecific motor impairments were not observed in these latter experiments. Collectively, these results suggest that the α₁-adrenergic receptor mediates the development of methamphetamine-conditioned hyperactivity and context-specific sensitization, perhaps by altering memory consolidation and/or reconsolidation processes. Copyright © 2014 Elsevier B.V. All rights reserved.

The time course of explicit and implicit categorization.

PubMed

Smith, J David; Zakrzewski, Alexandria C; Herberger, Eric R; Boomer, Joseph; Roeder, Jessica L; Ashby, F Gregory; Church, Barbara A

2015-10-01

Contemporary theory in cognitive neuroscience distinguishes, among the processes and utilities that serve categorization, explicit and implicit systems of category learning that learn, respectively, category rules by active hypothesis testing or adaptive behaviors by association and reinforcement. Little is known about the time course of categorization within these systems. Accordingly, the present experiments contrasted tasks that fostered explicit categorization (because they had a one-dimensional, rule-based solution) or implicit categorization (because they had a two-dimensional, information-integration solution). In Experiment 1, participants learned categories under unspeeded or speeded conditions. In Experiment 2, they applied previously trained category knowledge under unspeeded or speeded conditions. Speeded conditions selectively impaired implicit category learning and implicit mature categorization. These results illuminate the processing dynamics of explicit/implicit categorization.

Harmonic Frequency Lowering

PubMed Central

Kirchberger, Martin

2016-01-01

A novel algorithm for frequency lowering in music was developed and experimentally tested in hearing-impaired listeners. Harmonic frequency lowering (HFL) combines frequency transposition and frequency compression to preserve the harmonic content of music stimuli. Listeners were asked to make judgments regarding detail and sound quality in music stimuli. Stimuli were presented under different signal processing conditions: original, low-pass filtered, HFL, and nonlinear frequency compressed. Results showed that participants reported perceiving the most detail in the HFL condition. In addition, there was no difference in sound quality across conditions. PMID:26834122

Electrochemical regeneration of phenol-saturated activated carbon - proposal of a reactor.

PubMed

Zanella, Odivan; Bilibio, Denise; Priamo, Wagner Luiz; Tessaro, Isabel Cristina; Féris, Liliana Amaral

2017-03-01

An electrochemical process was used to investigate the activated carbon regeneration efficiency (RE) saturated with aromatics. For this purpose, an electrochemical reactor was developed and the operational conditions of this equipment were investigated, which is applied in activated carbon regeneration process. The influence of regeneration parameters such as processing time, the current used, the polarity and the processing fluid (electrolyte) were studied. The performance of electrochemical regeneration was evaluated by adsorption tests, using phenol as adsorbate. The increase in current applied and the process time was found to enhance the RE. Another aspect that indicated a better reactor performance was the type of electrolyte used, showing best results for NaCl. The polarity showed the highest influence on the process, when the cathodic regeneration was more efficient. The electrochemical regeneration process developed in this study presented regeneration capacities greater than 100% when the best process conditions were used, showing that this form of regeneration for activated carbon saturated with aromatics is very promising.

An autism-associated serotonin transporter variant disrupts multisensory processing.

PubMed

Siemann, J K; Muller, C L; Forsberg, C G; Blakely, R D; Veenstra-VanderWeele, J; Wallace, M T

2017-03-21

Altered sensory processing is observed in many children with autism spectrum disorder (ASD), with growing evidence that these impairments extend to the integration of information across the different senses (that is, multisensory function). The serotonin system has an important role in sensory development and function, and alterations of serotonergic signaling have been suggested to have a role in ASD. A gain-of-function coding variant in the serotonin transporter (SERT) associates with sensory aversion in humans, and when expressed in mice produces traits associated with ASD, including disruptions in social and communicative function and repetitive behaviors. The current study set out to test whether these mice also exhibit changes in multisensory function when compared with wild-type (WT) animals on the same genetic background. Mice were trained to respond to auditory and visual stimuli independently before being tested under visual, auditory and paired audiovisual (multisensory) conditions. WT mice exhibited significant gains in response accuracy under audiovisual conditions. In contrast, although the SERT mutant animals learned the auditory and visual tasks comparably to WT littermates, they failed to show behavioral gains under multisensory conditions. We believe these results provide the first behavioral evidence of multisensory deficits in a genetic mouse model related to ASD and implicate the serotonin system in multisensory processing and in the multisensory changes seen in ASD.

Right Occipital Cortex Activation Correlates with Superior Odor Processing Performance in the Early Blind

PubMed Central

Grandin, Cécile B.; Dricot, Laurence; Plaza, Paula; Lerens, Elodie; Rombaux, Philippe; De Volder, Anne G.

2013-01-01

Using functional magnetic resonance imaging (fMRI) in ten early blind humans, we found robust occipital activation during two odor-processing tasks (discrimination or categorization of fruit and flower odors), as well as during control auditory-verbal conditions (discrimination or categorization of fruit and flower names). We also found evidence for reorganization and specialization of the ventral part of the occipital cortex, with dissociation according to stimulus modality: the right fusiform gyrus was most activated during olfactory conditions while part of the left ventral lateral occipital complex showed a preference for auditory-verbal processing. Only little occipital activation was found in sighted subjects, but the same right-olfactory/left-auditory-verbal hemispheric lateralization was found overall in their brain. This difference between the groups was mirrored by superior performance of the blind in various odor-processing tasks. Moreover, the level of right fusiform gyrus activation during the olfactory conditions was highly correlated with individual scores in a variety of odor recognition tests, indicating that the additional occipital activation may play a functional role in odor processing. PMID:23967263

XV-15 Tiltrotor Aircraft: 1999 Acoustic Testing - Test Report

NASA Technical Reports Server (NTRS)

Edwards, Bryan D.; Conner, David A.

2003-01-01

An XV-15 acoustic test is discussed, and measured results are presented. The test was conducted by NASA Langley and Bell Helicopter Textron, Inc., during October 1999, at the BHTI test site near Waxahachie, Texas. As part of the NASA-sponsored Short Haul Civil Tiltrotor noise reduction initiative, this was the third in a series of three major XV-15 acoustic tests. Their purpose was to document the acoustic signature of the XV-15 tiltrotor aircraft for a variety of flight conditions and to minimize the noise signature during approach. Tradeoffs between flight procedures and the measured noise are presented to illustrate the noise abatement flight procedures. The test objectives were to support operation of future tiltrotors by further developing and demonstrating low-noise flight profiles, while maintaining acceptable handling and ride qualities, and refine approach profiles, selected from previous (1995 & 1997) tiltrotor testing, to incorporate Instrument Flight Rules (IFR), handling qualities constraints, operations and tradeoffs with sound. Primary emphasis was given to the approach flight conditions where blade-vortex interaction (BVI) noise dominates, because this condition influences community noise impact more than any other. An understanding of this part of the noise generating process could guide the development of low noise flight operations and increase the tiltrotor's acceptance in the community.

Evaluation of biochar-ultrafiltration membrane processes for humic acid removal under various hydrodynamic, pH, ionic strength, and pressure conditions.

PubMed

Shankar, Vaibhavi; Heo, Jiyong; Al-Hamadani, Yasir A J; Park, Chang Min; Chu, Kyoung Hoon; Yoon, Yeomin

2017-07-15

The performance of an ultrafiltration (UF)-biochar process was evaluated in comparison with a UF membrane process for the removal of humic acid (HA). Bench-scale UF experiments were conducted to study the rejection and flux trends under various hydrodynamic, pH, ionic strength, and pressure conditions. The resistance-in-series model was used to evaluate the processes and it showed that unlike stirred conditions, where low fouling resistance was observed (28.7 × 10 12  m -1 to 32.5 × 10 12  m -1 ), higher values and comparable trends were obtained for UF-biochar and UF alone for unstirred conditions (28.7 × 10 12  m -1 to 32.5 × 10 12  m -1 ). Thus, the processes were further evaluated under unstirred conditions. Additionally, total fouling resistance was decreased in the presence of biochar by 6%, indicating that HA adsorption by biochar could diminish adsorption fouling on the UF membrane and thus improve the efficiency of the UF-biochar process. The rejection trends of UF-biochar and UF alone were similar in most cases, whereas UF-biochar showed a noticeable increase in flux of around 18-25% under various experimental conditions due to reduced membrane fouling. Three-cycle filtration tests further demonstrated that UF-biochar showed better membrane recovery and antifouling capability by showing more HA rejection (3-5%) than UF membrane alone with each subsequent cycle of filtration. As a result of these findings, the UF-biochar process may potentially prove be a viable treatment option for the removal of HA from water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Theoretical and testing performance of an innovative indirect evaporative chiller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Yi; Xie, Xiaoyun

2010-12-15

An indirect evaporative chiller is a device used to produce chilled water at a temperature between the wet bulb temperature and dew point of the outdoor air, which can be used in building HVAC systems. This article presents a theoretical analysis and practical performance of an innovative indirect evaporative chiller. First, the process of the indirect evaporative chiller is introduced; then, the matching characteristics of the process are presented and analyzed. It can be shown that the process that produces cold water by using dry air is a nearly-reversible process, so the ideal produced chilled water temperature of the indirectmore » evaporative chiller can be set close to the dew point temperature of the chiller's inlet air. After the indirect evaporative chiller was designed, simulations were done to analyze the output water temperature, the cooling efficiency relative to the inlet dew point temperature, and the COP that the chiller can performance. The first installation of the indirect evaporative chiller of this kind has been run for 5 years in a building in the city of Shihezi. The tested output water temperature of the chiller is around 14-20 C, which is just in between of the outdoor wet bulb temperature and dew point. The tested COP{sub r,s} of the developed indirect evaporative chiller reaches 9.1. Compared with ordinary air conditioning systems, the indirect evaporative chiller can save more than 40% in energy consumption due to the fact that the only energy consumed is from pumps and fans. An added bonus is that the indirect evaporative chiller uses no CFCs that pollute to the aerosphere. The tested internal parameters, such as the water-air flow rate ratio and heat transfer area for each heat transfer process inside the chiller, were analyzed and compared with designed values. The tested indoor air conditions, with a room temperature of 23-27 C and relative humidity of 50-70%, proved that the developed practical indirect evaporative chiller successfully satisfy the indoor air conditioning load for the demo building. The indirect evaporative chiller has a potentially wide application in dry regions, especially for large scale commercial buildings. Finally, this paper presented the geographic regions suitable for the technology worldwide. (author)« less

Motor-cognitive dual-task performance: effects of a concurrent motor task on distinct components of visual processing capacity.

PubMed

Künstler, E C S; Finke, K; Günther, A; Klingner, C; Witte, O; Bublak, P

2018-01-01

Dual tasking, or the simultaneous execution of two continuous tasks, is frequently associated with a performance decline that can be explained within a capacity sharing framework. In this study, we assessed the effects of a concurrent motor task on the efficiency of visual information uptake based on the 'theory of visual attention' (TVA). TVA provides parameter estimates reflecting distinct components of visual processing capacity: perceptual threshold, visual processing speed, and visual short-term memory (VSTM) storage capacity. Moreover, goodness-of-fit values and bootstrapping estimates were derived to test whether the TVA-model is validly applicable also under dual task conditions, and whether the robustness of parameter estimates is comparable in single- and dual-task conditions. 24 subjects of middle to higher age performed a continuous tapping task, and a visual processing task (whole report of briefly presented letter arrays) under both single- and dual-task conditions. Results suggest a decline of both visual processing capacity and VSTM storage capacity under dual-task conditions, while the perceptual threshold remained unaffected by a concurrent motor task. In addition, goodness-of-fit values and bootstrapping estimates support the notion that participants processed the visual task in a qualitatively comparable, although quantitatively less efficient way under dual-task conditions. The results support a capacity sharing account of motor-cognitive dual tasking and suggest that even performing a relatively simple motor task relies on central attentional capacity that is necessary for efficient visual information uptake.

Storage and retrieval properties of dual codes for pictures and words in recognition memory.

PubMed

Snodgrass, J G; McClure, P

1975-09-01

Storage and retrieval properties of pictures and words were studied within a recognition memory paradigm. Storage was manipulated by instructing subjects either to image or to verbalize to both picture and word stimuli during the study sequence. Retrieval was manipulated by representing a proportion of the old picture and word items in their opposite form during the recognition test (i.e., some old pictures were tested with their corresponding words and vice versa). Recognition performance for pictures was identical under the two instructional conditions, whereas recognition performance for words was markedly superior under the imagery instruction condition. It was suggested that subjects may engage in dual coding of simple pictures naturally, regardless of instructions, whereas dual coding of words may occur only under imagery instructions. The form of the test item had no effect on recognition performance for either type of stimulus and under either instructional condition. However, change of form of the test item markedly reduced item-by-item correlations between the two instructional conditions. It is tentatively proposed that retrieval is required in recognition, but that the effect of a form change is simply to make the retrieval process less consistent, not less efficient.

Influence of central set on anticipatory and triggered grip-force adjustments

NASA Technical Reports Server (NTRS)

Winstein, C. J.; Horak, F. B.; Fisher, B. E.; Peterson, B. W. (Principal Investigator)

2000-01-01

The effects of predictability of load magnitude on anticipatory and triggered grip-force adjustments were studied as nine normal subjects used a precision grip to lift, hold, and replace an instrumented test object. Experience with a predictable stimulus has been shown to enhance magnitude scaling of triggered postural responses to different amplitudes of perturbations. However, this phenomenon, known as a central-set effect, has not been tested systematically for grip-force responses in the hand. In our study, predictability was manipulated by applying load perturbations of different magnitudes to the test object under conditions in which the upcoming load magnitude was presented repeatedly or under conditions in which the load magnitudes were presented randomly, each with two different pre-load grip conditions (unconstrained and constrained). In constrained conditions, initial grip forces were maintained near the minimum level necessary to prevent pre-loaded object slippage, while in unconstrained conditions, no initial grip force restrictions were imposed. The effect of predictable (blocked) and unpredictable (random) load presentations on scaling of anticipatory and triggered grip responses was tested by comparing the slopes of linear regressions between the imposed load and grip response magnitude. Anticipatory and triggered grip force responses were scaled to load magnitude in all conditions. However, regardless of pre-load grip force constraint, the gains (slopes) of grip responses relative to load magnitudes were greater when the magnitude of the upcoming load was predictable than when the load increase was unpredictable. In addition, a central-set effect was evidenced by the fewer number of drop trials in the predictable relative to unpredictable load conditions. Pre-load grip forces showed the greatest set effects. However, grip responses showed larger set effects, based on prediction, when pre-load grip force was constrained to lower levels. These results suggest that anticipatory processes pertaining to load magnitude permit the response gain of both voluntary and triggered rapid grip force adjustments to be set, at least partially, prior to perturbation onset. Comparison of anticipatory set effects for reactive torque and lower extremity EMG postural responses triggered by surface translation perturbations suggests a more general rule governing anticipatory processes.

Tracer test with As(V) under variable redox conditions controlling arsenic transport in the presence of elevated ferrous iron concentrations

USGS Publications Warehouse

Hohn, R.; Isenbeck-Schroter, M.; Kent, D.B.; Davis, J.A.; Jakobsen, R.; Jann, S.; Niedan, V.; Scholz, C.; Stadler, S.; Tretner, A.

2006-01-01

To study transport and reactions of arsenic under field conditions, a small-scale tracer test was performed in an anoxic, iron-reducing zone of a sandy aquifer at the USGS research site on Cape Cod, Massachusetts, USA. For four weeks, a stream of groundwater with added As(V) (6.7????M) and bromide (1.6??mM), was injected in order to observe the reduction of As(V) to As(III). Breakthrough of bromide (Br-), As(V), and As(III) as well as additional parameters characterizing the geochemical conditions was observed at various locations downstream of the injection well over a period of 104??days. After a short lag period, nitrate and dissolved oxygen from the injectate oxidized ferrous iron and As(V) became bound to the freshly formed hydrous iron oxides. Approximately one week after terminating the injection, anoxic conditions had been reestablished and increases in As(III) concentrations were observed within 1??m of the injection. During the observation period, As(III) and As(V) were transported to a distance of 4.5??m downgradient indicating significant retardation by sorption processes for both species. Sediment assays as well as elevated concentrations of hydrogen reflected the presence of As(V) reducing microorganisms. Thus, microbial As(V) reduction was thought to be one major process driving the release of As(III) during the tracer test in the Cape Cod aquifer. ?? 2006 Elsevier B.V. All rights reserved.

Evaluation of moisture reduction in small diameter trees after crushing

Treesearch

Donald L. Sirois; Cynthia L. Rawlins; Bryce J. Stokes

1991-01-01

Past studies have suggested that processing small diameter whole trees like those foumd on rights-of-way (ROWs) would help reduce transportion costs and increase energy value by lowering stem moisture content. Small stems were crushed by a roller crusher/splitter test bench machine and allowed dry under field conditions in Alabama. Tests were conducted in winter and...

MicroHH 1.0: a computational fluid dynamics code for direct numerical simulation and large-eddy simulation of atmospheric boundary layer flows

NASA Astrophysics Data System (ADS)

van Heerwaarden, Chiel C.; van Stratum, Bart J. H.; Heus, Thijs; Gibbs, Jeremy A.; Fedorovich, Evgeni; Mellado, Juan Pedro

2017-08-01

This paper describes MicroHH 1.0, a new and open-source (www.microhh.org) computational fluid dynamics code for the simulation of turbulent flows in the atmosphere. It is primarily made for direct numerical simulation but also supports large-eddy simulation (LES). The paper covers the description of the governing equations, their numerical implementation, and the parameterizations included in the code. Furthermore, the paper presents the validation of the dynamical core in the form of convergence and conservation tests, and comparison of simulations of channel flows and slope flows against well-established test cases. The full numerical model, including the associated parameterizations for LES, has been tested for a set of cases under stable and unstable conditions, under the Boussinesq and anelastic approximations, and with dry and moist convection under stationary and time-varying boundary conditions. The paper presents performance tests showing good scaling from 256 to 32 768 processes. The graphical processing unit (GPU)-enabled version of the code can reach a speedup of more than an order of magnitude for simulations that fit in the memory of a single GPU.

Microstructural examination of fatigue crack tip in high strength steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuoka, C.; Yoshizawa, H.; Nakagawa, Y.G.

1993-10-01

Fatigue tests were performed to examine how microstructural conditioning influences crack initiation and propagation in SA508 class 3 low-carbon steel. A 3-mm-long crack was introduced in compact tension (CT) fatigue test specimens under four different loads in order to obtain crack tip plastic zones at different stress intensity factor ranges, [Delta]K = 18, 36, 54, and 72 MPa[radical]m. The microstructure of the plastic zones around the crack tip were examined by transmission electron microscopy (TEM) and selected area electron diffraction (SAD). Micro-orientation of the dislocation cells in the plastic zones of all of the CT samples increased to 4 degmore » from the level of an as-received sample. Four-point bending fatigue tests were performed for plate shape samples with a large cyclic strain range. The SAD value of the bending samples was also 4 deg in the damaged area where cracks already initiated at an early stage of the fatigue process. These test results indicate that the microstructural conditioning is a prerequisite for the fatigue crack initiation and propagation in SA508. These observations may lead to better understanding of how fatigue initiation processes transit to cracks.« less

Martial Art Training and Cognitive Performance in Middle-Aged Adults.

PubMed

Douris, Peter; Douris, Christopher; Balder, Nicole; LaCasse, Michael; Rand, Amir; Tarapore, Freya; Zhuchkan, Aleskey; Handrakis, John

2015-09-29

Cognitive performance includes the processes of attention, memory, processing speed, and executive functioning, which typically declines with aging. Previous research has demonstrated that aerobic and resistance exercise improves cognitive performance immediately following exercise. However, there is limited research examining the effect that a cognitively complex exercise such as martial art training has on these cognitive processes. Our study compared the acute effects of 2 types of martial art training to aerobic exercise on cognitive performance in middle-aged adults. We utilized a repeated measures design with the order of the 3 exercise conditions randomly assigned and counterbalanced. Ten recreational middle-aged martial artists (mean age = 53.5 ± 8.6 years) participated in 3 treatment conditions: a typical martial art class, an atypical martial art class, and a one-hour walk at a self-selected speed. Cognitive performance was assessed by the Stroop Color and Word test. While all 3 exercise conditions improved attention and processing speed, only the 2 martial art conditions improved the highest order of cognitive performance, executive function. The effect of the 2 martial art conditions on executive function was not different. The improvement in executive function may be due to the increased cortical demand required by the more complex, coordinated motor tasks of martial art exercise compared to the more repetitive actions of walking.

Martial Art Training and Cognitive Performance in Middle-Aged Adults

PubMed Central

Douris, Peter; Douris, Christopher; Balder, Nicole; LaCasse, Michael; Rand, Amir; Tarapore, Freya; Zhuchkan, Aleskey; Handrakis, John

2015-01-01

Cognitive performance includes the processes of attention, memory, processing speed, and executive functioning, which typically declines with aging. Previous research has demonstrated that aerobic and resistance exercise improves cognitive performance immediately following exercise. However, there is limited research examining the effect that a cognitively complex exercise such as martial art training has on these cognitive processes. Our study compared the acute effects of 2 types of martial art training to aerobic exercise on cognitive performance in middle-aged adults. We utilized a repeated measures design with the order of the 3 exercise conditions randomly assigned and counterbalanced. Ten recreational middle-aged martial artists (mean age = 53.5 ± 8.6 years) participated in 3 treatment conditions: a typical martial art class, an atypical martial art class, and a one-hour walk at a self-selected speed. Cognitive performance was assessed by the Stroop Color and Word test. While all 3 exercise conditions improved attention and processing speed, only the 2 martial art conditions improved the highest order of cognitive performance, executive function. The effect of the 2 martial art conditions on executive function was not different. The improvement in executive function may be due to the increased cortical demand required by the more complex, coordinated motor tasks of martial art exercise compared to the more repetitive actions of walking. PMID:26672872

Advanced Turbine Technology Applications Project (ATTAP)

NASA Technical Reports Server (NTRS)

1991-01-01

This report summarizes work performed in support of the development and demonstration of a structural ceramic technology for automotive gas turbine engines. The AGT101 regenerated gas turbine engine developed under the previous DOE/NASA Advanced Gas Turbine (AGT) program is being utilized for verification testing of the durability of next-generation ceramic components and their suitability for service at reference powertrain design conditions. Topics covered in this report include ceramic processing definition and refinement, design improvements to the test bed engine and test rigs, and design methodologies related to ceramic impact and fracture mechanisms. Appendices include reports by ATTAP subcontractors addressing the development of silicon nitride and silicon carbide families of materials and processes.

A computerized test system for thermal-mechanical fatigue crack growth

NASA Technical Reports Server (NTRS)

Marchand, N.; Pelloux, R. M.

1986-01-01

A computerized testing system to measure fatigue crack growth under thermal-mechanical fatigue conditions is described. Built around a servohydraulic machine, the system is capable of a push-pull test under stress-controlled or strain-controlled conditions in the temperature range of 25 to 1050 C. Temperature and mechanical strain are independently controlled by the closed-loop system to simulate the complex inservice strain-temperature relationship. A d-c electrical potential method is used to measure crack growth rates. The correction procedure of the potential signal to take into account powerline and RF-induced noises and thermal changes is described. It is shown that the potential drop technique can be used for physical mechanism studies and for modelling crack tip processes.

Pyro shock simulation: Experience with the MIPS simulator

NASA Technical Reports Server (NTRS)

Dwyer, Thomas J.; Moul, David S.

1988-01-01

The Mechanical Impulse Pyro Shock (MIPS) Simulator at GE Astro Space Division is one version of a design that is in limited use throughout the aerospace industry, and is typically used for component shock testing at levels up to 10,000 response g's. Modifications to the force imput, table and component boundary conditions have allowed a range of test conditions to be achieved. Twelve different designs of components with weights up to 23 Kg are in the process or have completed qualification testing in the Dynamic Simulation Lab at GE in Valley Forge, Pa. A summary of the experience gained through the use of this simulator is presented as well as examples of shock experiments that can be readily simulated at the GE Astro MIPS facility.

Modality dependence and intermodal transfer in the Corsi Spatial Sequence Task: Screen vs. Floor.

PubMed

Röser, Andrea; Hardiess, Gregor; Mallot, Hanspeter A

2016-07-01

Four versions of the Corsi Spatial Sequence Task (CSST) were tested in a complete within-subject design, investigating whether participants' performance depends on the modality of task presentation and reproduction that put different demands on spatial processing. Presentation of the sequence (encoding phase) and the reproduction (recall phase) were each carried out either on a computer screen or on the floor of a room, involving actual walking in the recall phase. Combinations of the two different encoding and recall procedures result in the modality conditions Screen-Screen, Screen-Floor, Floor-Screen, and Floor-Floor. Results show the expected decrease in performance with increasing sequence length, which is likely due to processing limitations of working memory. We also found differences in performance between the modality conditions indicating different involvements of spatial working memory processes. Participants performed best in the Screen-Screen modality condition. Floor-Screen and Floor-Floor modality conditions require additional working memory resources for reference frame transformation and spatial updating, respectively; the resulting impairment of the performance was about the same in these two conditions. Finally, the Screen-Floor modality condition requires both types of additional spatial demands and led to the poorest performance. Therefore, we suggest that besides the well-known spatial requirements of CSST, additional working memory resources are demanded in walking CSST supporting processes such as spatial updating, mental rotation, reference frame transformation, and the control of walking itself.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gould, Benjamin; Greco, Aaron

White etching cracks (WECs) have been identified as a dominant mode of premature failure within wind turbine gearbox bearings. Though WECs have been reported in the field for over a decade, the conditions leading to WECs, and the process by which this failure culminates, are both highly debated. In previously published work, the generation of WECs on a benchtop scale was linked to sliding at the surface of the test sample, it was also postulated that the generation of WECs was dependent on the cumulative energy that had been applied to the sample over the entirety of the test. Inmore » this paper, a three ring on roller bench top test rig is used to systematically alter the cumulative energy that a sample experiences through changes in normal load, sliding, and run time, in an attempt to correlate cumulative energy with the formation of WECs. It was determined that, in the current test setup, the presence of WECs can be predicted by this energy criterion. The authors then used this information to study the process by which WECs initiate. Lastly, it was found that, under the current testing conditions, the formation of a dark etching microstructure precedes the formation of a crack, and a crack precedes the formation of white etching microstructure.« less

DESTRUCTION OF TETRAPHENYLBORATE IN TANK 48H USING WET AIR OXIDATION BATCH BENCH SCALE AUTOCLAVE TESTING WITH ACTUAL RADIOACTIVE TANK 48H WASTE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adu-Wusu, K; Paul Burket, P

2009-03-31

Wet Air Oxidation (WAO) is one of the two technologies being considered for the destruction of Tetraphenylborate (TPB) in Tank 48H. Batch bench-scale autoclave testing with radioactive (actual) Tank 48H waste is among the tests required in the WAO Technology Maturation Plan. The goal of the autoclave testing is to validate that the simulant being used for extensive WAO vendor testing adequately represents the Tank 48H waste. The test objective was to demonstrate comparable test results when running simulated waste and real waste under similar test conditions. Specifically: (1) Confirm the TPB destruction efficiency and rate (same reaction times) obtainedmore » from comparable simulant tests, (2) Determine the destruction efficiency of other organics including biphenyl, (3) Identify and quantify the reaction byproducts, and (4) Determine off-gas composition. Batch bench-scale stirred autoclave tests were conducted with simulated and actual Tank 48H wastes at SRNL. Experimental conditions were chosen based on continuous-flow pilot-scale simulant testing performed at Siemens Water Technologies Corporation (SWT) in Rothschild, Wisconsin. The following items were demonstrated as a result of this testing. (1) Tetraphenylborate was destroyed to below detection limits during the 1-hour reaction time at 280 C. Destruction efficiency of TPB was > 99.997%. (2) Other organics (TPB associated compounds), except biphenyl, were destroyed to below their respective detection limits. Biphenyl was partially destroyed in the process, mainly due to its propensity to reside in the vapor phase during the WAO reaction. Biphenyl is expected to be removed in the gas phase during the actual process, which is a continuous-flow system. (3) Reaction byproducts, remnants of MST, and the PUREX sludge, were characterized in this work. Radioactive species, such as Pu, Sr-90 and Cs-137 were quantified in the filtrate and slurry samples. Notably, Cs-137, boron and potassium were shown as soluble as a result of the WAO reaction. (4) Off-gas composition was measured in the resulting gas phase from the reaction. Benzene and hydrogen were formed during the reaction, but they were reasonably low in the off-gas at 0.096 and 0.0063 vol% respectively. Considering the consistency in replicating similar test results with simulated waste and Tank 48H waste under similar test conditions, the results confirm the validity of the simulant for other WAO test conditions.« less

Methods and Systems for Advanced Spaceport Information Management

NASA Technical Reports Server (NTRS)

Fussell, Ronald M. (Inventor); Ely, Donald W. (Inventor); Meier, Gary M. (Inventor); Halpin, Paul C. (Inventor); Meade, Phillip T. (Inventor); Jacobson, Craig A. (Inventor); Blackwell-Thompson, Charlie (Inventor)

2007-01-01

Advanced spaceport information management methods and systems are disclosed. In one embodiment, a method includes coupling a test system to the payload and transmitting one or more test signals that emulate an anticipated condition from the test system to the payload. One or more responsive signals are received from the payload into the test system and are analyzed to determine whether one or more of the responsive signals comprises an anomalous signal. At least one of the steps of transmitting, receiving, analyzing and determining includes transmitting at least one of the test signals and the responsive signals via a communications link from a payload processing facility to a remotely located facility. In one particular embodiment, the communications link is an Internet link from a payload processing facility to a remotely located facility (e.g. a launch facility, university, etc.).

Methods and systems for advanced spaceport information management

NASA Technical Reports Server (NTRS)

Ely, Donald W. (Inventor); Fussell, Ronald M. (Inventor); Halpin, Paul C. (Inventor); Blackwell-Thompson, Charlie (Inventor); Meier, Gary M. (Inventor); Meade, Phillip T. (Inventor); Jacobson, Craig A. (Inventor)

2007-01-01

Advanced spaceport information management methods and systems are disclosed. In one embodiment, a method includes coupling a test system to the payload and transmitting one or more test signals that emulate an anticipated condition from the test system to the payload. One or more responsive signals are received from the payload into the test system and are analyzed to determine whether one or more of the responsive signals comprises an anomalous signal. At least one of the steps of transmitting, receiving, analyzing and determining includes transmitting at least one of the test signals and the responsive signals via a communications link from a payload processing facility to a remotely located facility. In one particular embodiment, the communications link is an Internet link from a payload processing facility to a remotely located facility (e.g. a launch facility, university, etc.).

ETV REPORT - EVALUATION OF DAVIS TECHNOLOGIES INTERNATIONAL CORP. - INDUSTRIAL WASTEWATER TREATMENT PLANT

EPA Science Inventory

Abstract: Evaluation of Davis Technologies International Corp. Industrial Wastewater Treatment Plant

The Davis Technologies International Corp. (DTIC) Industrial Wastewater Treatment Plant (IWTP) was tested, under actual production conditions, processing metalworking and ...

Investigation of factors affecting in vitro doxorubicin release from PEGylated liposomal doxorubicin for the development of in vitro release testing conditions.

PubMed

Shibata, Hiroko; Izutsu, Ken-Ichi; Yomota, Chikako; Okuda, Haruhiro; Goda, Yukihiro

2015-01-01

Establishing appropriate drug release testing methods of liposomal products for assuring quality and performance requires the determination of factors affecting in vitro drug release. In this study, we investigated the effects of test conditions (human plasma lot, pH/salt concentration in the test media, dilution factor, temperature, ultrasound irradiation, etc.), and liposomal preparation conditions (pH/concentration of ammonium sulfate solution), on doxorubicin (DXR) release from PEGylated liposomal DXR. Higher temperature and lower pH significantly increased DXR release. The evaluation of DXR solubility indicated that the high DXR release induced by low pH may be attributed to the high solubility of DXR at low pH. Ultrasound irradiation induced rapid DXR release in an amplitude-dependent manner. The salt concentration in the test solution, human plasma lot, and dilution factor had a limited impact on DXR-release. Variations in the ammonium sulfate concentration used in solutions for the formation/hydration of liposomes significantly affected DXR release behavior, whereas differences in pH did not. In addition, heating condition in phosphate-buffered saline at lower pH (<6.5) exhibited higher discriminative ability for the release profiles from various liposomes with different concentrations of ammonium sulfate than did ultrasound irradiation. These results are expected to be helpful in the process of establishing appropriate drug release testing methods for PEGylated liposomal DXR.

Memory retrieval as a self-propagating process.

PubMed

Bäuml, Karl-Heinz T; Schlichting, Andreas

2014-07-01

Retrieval of a subset of studied items and the presentation of those items as retrieval cues typically impair retrieval of the other items. Previous research on this self-limiting property of memory retrieval has relied heavily on short retention intervals and similar context between encoding and test. Here, we examined retrieval dynamics also after a prolonged retention interval with different spatial and social context between encoding and test, conditions that mimic people's remembering in many situations of daily life. For both unrelated word lists and more integrated prose material, we found retrieval and cuing to impair recall of other studied items after a short retention interval, but to improve recall in the prolonged retention interval condition. The results demonstrate that retrieval dynamics depend critically on situation, indicating that quite often in daily life, retrieval may be a self-propagating, rather than a self-limiting process. Copyright © 2014 Elsevier B.V. All rights reserved.

Laser Beam Welding of Ultra-high Strength Chromium Steel with Martensitic Microstructure

NASA Astrophysics Data System (ADS)

Dahmen, Martin; Janzen, Vitalij; Lindner, Stefan; Wagener, Rainer

A new class of steels is going to be introduced into sheet manufacturing. Stainless ferritic and martensitic steels open up opportunities for sheet metal fabrication including hot stamping. Strengths of up to 2 GPa at fracture elongations of 15% can be attained through this. Welding of these materials, as a result, became a challenge. Energy-reduced welding methods with in-situ heat treatment are required in order to ensure the delicate and complex heat control. Laser beam welding is the joining technique of choice to supply minimum heat input to the fusion process and to apply efficient heat control. For two application cases, tailored blank production in as-rolled condition and welding during assembly in hot stamped condition, welding processes have been developed. The welding suitability is shown through metallurgical investigations of the welds. Crash tests based on the KS-II concept as well as fatigue tests prove the applicability of the joining method.

Odour intensity learning in fruit flies

PubMed Central

Yarali, Ayse; Ehser, Sabrina; Hapil, Fatma Zehra; Huang, Ju; Gerber, Bertram

2009-01-01

Animals' behaviour towards odours depends on both odour quality and odour intensity. While neuronal coding of odour quality is fairly well studied, how odour intensity is treated by olfactory systems is less clear. Here we study odour intensity processing at the behavioural level, using the fruit fly Drosophila melanogaster. We trained flies by pairing a MEDIUM intensity of an odour with electric shock, and then, at a following test phase, measured flies' conditioned avoidance of either this previously trained MEDIUM intensity or a LOWer or a HIGHer intensity. With respect to 3-octanol, n-amylacetate and 4-methylcyclohexanol, we found that conditioned avoidance is strongest when training and test intensities match, speaking for intensity-specific memories. With respect to a fourth odour, benzaldehyde, on the other hand, we found no such intensity specificity. These results form the basis for further studies of odour intensity processing at the behavioural, neuronal and molecular level. PMID:19586944

Neural correlates of the spacing effect in explicit verbal semantic encoding support the deficient-processing theory.

PubMed

Callan, Daniel E; Schweighofer, Nicolas

2010-04-01

Spaced presentations of to-be-learned items during encoding leads to superior long-term retention over massed presentations. Despite over a century of research, the psychological and neural basis of this spacing effect however is still under investigation. To test the hypotheses that the spacing effect results either from reduction in encoding-related verbal maintenance rehearsal in massed relative to spaced presentations (deficient processing hypothesis) or from greater encoding-related elaborative rehearsal of relational information in spaced relative to massed presentations (encoding variability hypothesis), we designed a vocabulary learning experiment in which subjects encoded paired-associates, each composed of a known word paired with a novel word, in both spaced and massed conditions during functional magnetic resonance imaging. As expected, recall performance in delayed cued-recall tests was significantly better for spaced over massed conditions. Analysis of brain activity during encoding revealed that the left frontal operculum, known to be involved in encoding via verbal maintenance rehearsal, was associated with greater performance-related increased activity in the spaced relative to massed condition. Consistent with the deficient processing hypothesis, a significant decrease in activity with subsequent episodes of presentation was found in the frontal operculum for the massed but not the spaced condition. Our results suggest that the spacing effect is mediated by activity in the frontal operculum, presumably by encoding-related increased verbal maintenance rehearsal, which facilitates binding of phonological and word level verbal information for transfer into long-term memory. Copyright 2009 Wiley-Liss, Inc.

PULSE COMBUSTOR DESIGN QUALIFICATION TEST AND CLEAN COAL FEEDSTOCK TEST - VOLUME I AND VOLUME II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

For this Cooperative Agreement, the pulse heater module is the technology envelope for an indirectly heated steam reformer. The field of use of the steam reformer pursuant to this Cooperative Agreement with DOE is for the processing of sub-bituminous coals and lignite. The main focus is the mild gasification of such coals for the generation of both fuel gas and char--for the steel industry is the main focus. An alternate market application for the substitution of metallurgical coke is also presented. This project was devoted to qualification of a 253-tube pulse heater module. This module was designed, fabricated, installed, instrumentedmore » and tested in a fluidized bed test facility. Several test campaigns were conducted. This larger heater is a 3.5 times scale-up of the previous pulse heaters that had 72 tubes each. The smaller heater has been part of previous pilot field testing of the steam reformer at New Bern, North Carolina. The project also included collection and reduction of mild gasification process data from operation of the process development unit (PDU). The operation of the PDU was aimed at conditions required to produce char (and gas) for the Northshore Steel Operations. Northshore Steel supplied the coal for the process unit tests.« less

Laser processing of thin films for industrial packaging

NASA Astrophysics Data System (ADS)

Sozzi, Michele; Lutey, Adrian H. A.; Cucinotta, Annamaria; Selleri, Stefano; Molari, Pier Gabriele

2014-05-01

Single layer thin-film materials such as aluminum, polyethylene, polypropylene, and their multi-layer combinations such as aluminum-paper have been exposed to different laser radiation. A wide number of samples have been processed with 10 - 12.5 ns IR and Green, and 500 - 800 ps IR laser radiation at different translating speeds ranging from 50 mm/s to 1 m/s. High quality incisions have been obtained for all tested materials within the experimental conditions. The presented results provide the necessary parameters for an efficient cut and processing of the tested materials, for the employment of pulsed laser sources in the packaging industry, allowing the laser to prevail in lieu of more costly and energy intensive methods.

A simple approach for the modeling of an ODS steel mechanical behavior in pilgering conditions

NASA Astrophysics Data System (ADS)

Vanegas-Márquez, E.; Mocellin, K.; Toualbi, L.; de Carlan, Y.; Logé, R. E.

2012-01-01

The optimization of the forming of ODS tubes is linked to the choice of an appropriated constitutive model for modeling the metal forming process. In the framework of a unified plastic constitutive theory, the strain-controlled cyclic characteristics of a ferritic ODS steel were analyzed and modeled with two different tests. The first test is a classical tension-compression test, and leads to cyclic softening at low to intermediate strain amplitudes. The second test consists in alternated uniaxial compressions along two perpendicular axes, and is selected based on the similarities with the loading path induced by the Fe-14Cr-1W-Ti ODS cladding tube pilgering process. This second test exhibits cyclic hardening at all tested strain amplitudes. Since variable strain amplitudes prevail in pilgering conditions, the parameters of the considered constitutive law were identified based on a loading sequence including strain amplitude changes. A proposed semi automated inverse analysis methodology is shown to efficiently provide optimal sets of parameters for the considered loading sequences. When compared to classical approaches, the model involves a reduced number of parameters, while keeping a good ability to capture stress changes induced by strain amplitude changes. Furthermore, the methodology only requires one test, which is an advantage when the amount of available material is limited. As two distinct sets of parameters were identified for the two considered tests, it is recommended to consider the loading path when modeling cold forming of the ODS steel.

Nitric-glycolic flowsheet testing for maximum hydrogen generation rate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, C. J.; Newell, J. D.; Williams, M. S.

The Defense Waste Processing Facility (DWPF) at the Savannah River Site is developing for implementation a flowsheet with a new reductant to replace formic acid. Glycolic acid has been tested over the past several years and found to effectively replace the function of formic acid in the DWPF chemical process. The nitric-glycolic flowsheet reduces mercury, significantly lowers the chemical generation of hydrogen and ammonia, allows purge reduction in the Sludge Receipt and Adjustment Tank (SRAT), stabilizes the pH and chemistry in the SRAT and the Slurry Mix Evaporator (SME), allows for effective adjustment of the SRAT/SME rheology, and is favorablemore » with respect to melter flammability. The objective of this work was to perform DWPF Chemical Process Cell (CPC) testing at conditions that would bound the catalytic hydrogen production for the nitric-glycolic flowsheet.« less

40 CFR Appendix A to Subpart Ddddd... - Methodology and Criteria for Demonstrating Eligibility for the Health-Based Compliance Alternatives

Code of Federal Regulations, 2012 CFR

2012-07-01

... rate, type of control devices, process parameters (e.g., maximum heat input), and non-process... control systems (if applicable) and explain why the conditions are worst-case. (c) Number of test runs... located at the outlet of the control device and prior to any releases to the atmosphere. (e) Collection of...

40 CFR Appendix A to Subpart Ddddd... - Methodology and Criteria for Demonstrating Eligibility for the Health-Based Compliance Alternatives

Code of Federal Regulations, 2011 CFR

2011-07-01

... rate, type of control devices, process parameters (e.g., maximum heat input), and non-process... control systems (if applicable) and explain why the conditions are worst-case. (c) Number of test runs... located at the outlet of the control device and prior to any releases to the atmosphere. (e) Collection of...

40 CFR Appendix A to Subpart Ddddd... - Methodology and Criteria for Demonstrating Eligibility for the Health-Based Compliance Alternatives

Code of Federal Regulations, 2010 CFR

2010-07-01

... rate, type of control devices, process parameters (e.g., maximum heat input), and non-process... control systems (if applicable) and explain why the conditions are worst-case. (c) Number of test runs... located at the outlet of the control device and prior to any releases to the atmosphere. (e) Collection of...

HACCP-Based Programs for Preventing Disease and Injury from Premise Plumbing: A Building Consensus

PubMed Central

McCoy, William F.; Rosenblatt, Aaron A.

2015-01-01

Thousands of preventable injuries and deaths are annually caused by microbial, chemical and physical hazards from building water systems. Water is processed in buildings before use; this can degrade the quality of the water. Processing steps undertaken on-site in buildings often include conditioning, filtering, storing, heating, cooling, pressure regulation and distribution through fixtures that restrict flow and temperature. Therefore, prevention of disease and injury requires process management. A process management framework for buildings is the hazard analysis and critical control point (HACCP) adaptation of failure mode effects analysis (FMEA). It has been proven effective for building water system management. Validation is proof that hazards have been controlled under operating conditions and may include many kinds of evidence including cultures of building water samples to detect and enumerate potentially pathogenic microorganisms. However, results from culture tests are often inappropriately used because the accuracy and precision are not sufficient to support specifications for control limit or action triggers. A reliable negative screen is based on genus-level Polymerase Chain Reaction (PCR) for Legionella in building water systems; however, building water samples with positive results from this test require further analysis by culture methods. PMID:26184325

HACCP-Based Programs for Preventing Disease and Injury from Premise Plumbing: A Building Consensus.

PubMed

McCoy, William F; Rosenblatt, Aaron A

2015-07-09

Thousands of preventable injuries and deaths are annually caused by microbial, chemical and physical hazards from building water systems. Water is processed in buildings before use; this can degrade the quality of the water. Processing steps undertaken on-site in buildings often include conditioning, filtering, storing, heating, cooling, pressure regulation and distribution through fixtures that restrict flow and temperature. Therefore, prevention of disease and injury requires process management. A process management framework for buildings is the hazard analysis and critical control point (HACCP) adaptation of failure mode effects analysis (FMEA). It has been proven effective for building water system management. Validation is proof that hazards have been controlled under operating conditions and may include many kinds of evidence including cultures of building water samples to detect and enumerate potentially pathogenic microorganisms. However, results from culture tests are often inappropriately used because the accuracy and precision are not sufficient to support specifications for control limit or action triggers. A reliable negative screen is based on genus-level Polymerase Chain Reaction (PCR) for Legionella in building water systems; however, building water samples with positive results from this test require further analysis by culture methods.

DATA SUMMARY REPORT SMALL SCALE MELTER TESTING OF HLW ALGORITHM GLASSES MATRIX1 TESTS VSL-07S1220-1 REV 0 7/25/07

DOE Office of Scientific and Technical Information (OSTI.GOV)

KRUGER AA; MATLACK KS; PEGG IL

2011-12-29

Eight tests using different HLW feeds were conducted on the DM100-BL to determine the effect of variations in glass properties and feed composition on processing rates and melter conditions (off-gas characteristics, glass processing, foaming, cold cap, etc.) at constant bubbling rate. In over seven hundred hours of testing, the property extremes of glass viscosity, electrical conductivity, and T{sub 1%}, as well as minimum and maximum concentrations of several major and minor glass components were evaluated using glass compositions that have been tested previously at the crucible scale. Other parameters evaluated with respect to glass processing properties were +/-15% batching errorsmore » in the addition of glass forming chemicals (GFCs) to the feed, and variation in the sources of boron and sodium used in the GFCs. Tests evaluating batching errors and GFC source employed variations on the HLW98-86 formulation (a glass composition formulated for HLW C-106/AY-102 waste and processed in several previous melter tests) in order to best isolate the effect of each test variable. These tests are outlined in a Test Plan that was prepared in response to the Test Specification for this work. The present report provides summary level data for all of the tests in the first test matrix (Matrix 1) in the Test Plan. Summary results from the remaining tests, investigating minimum and maximum concentrations of major and minor glass components employing variations on the HLW98-86 formulation and glasses generated by the HLW glass formulation algorithm, will be reported separately after those tests are completed. The test data summarized herein include glass production rates, the type and amount of feed used, a variety of measured melter parameters including temperatures and electrode power, feed sample analysis, measured glass properties, and gaseous emissions rates. More detailed information and analysis from the melter tests with complete emission chemistry, glass durability, and melter operating details will be provided in the final report. A summary of the tests that were conducted is provided in Table 1. Each of the seven tests was of nominally one hundred hours in duration. Test B was conducted in two equal segments: the first with nominal additives, and the second with the replacement of borax with a mixture of boric acid and soda ash to determine the effect of alternative OPC sources on production rates and processing characteristics. Interestingly, sugar additions were required near mid points of Tests W and Z to reduce excessive foaming that severely limited feed processing rates. The sugar additions were very effective in recovering manageable processing conditions, albeit over the relatively short remainder of the test duration. Tests W and Z employed the highest melt viscosities but not by a particularly wide margin. Other tests, which did not exhibit such foaming Issues, employed higher concentrations of manganese or iron or both. These results highlight the need for the development of protocols for the a priori determination of which HLW feeds will require sugar additions and the appropriate amounts of sugar to be added in order to control foaming (and maintain throughput) without over-reduction of the melt (which could lead to molten metal formation). In total, over 8,800 kg of feed was processed to produce over 3200 kg of glass. Steady-state processing rates were achieved, and no secondary sulfate phases were observed during any of the tests. Analysis was performed on samples of the glass product taken throughout the tests to verify composition and properties. Sampling and analysis was also performed on melter exhaust to determine the effect of the feed and glass changes on melter emissions.« less

Working memory load eliminates the survival processing effect.

PubMed

Kroneisen, Meike; Rummel, Jan; Erdfelder, Edgar

2014-01-01

In a series of experiments, Nairne, Thompson, and Pandeirada (2007) demonstrated that words judged for their relevance to a survival scenario are remembered better than words judged for a scenario not relevant on a survival dimension. They explained this survival-processing effect by arguing that nature "tuned" our memory systems to process and remember fitness-relevant information. Kroneisen and Erdfelder (2011) proposed that it may not be survival processing per se that facilitates recall but the richness and distinctiveness with which information is encoded. To further test this account, we investigated how the survival processing effect is affected by cognitive load. If the survival processing effect is due to automatic processes or, alternatively, if survival processing is routinely prioritized in dual-task contexts, we would expect this effect to persist under cognitive load conditions. If the effect relies on cognitively demanding processes like richness and distinctiveness of encoding, however, the survival processing benefit should be hampered by increased cognitive load during encoding. Results were in line with the latter prediction, that is, the survival processing effect vanished under dual-task conditions.

Intentional and automatic processing of numerical information in mathematical anxiety: testing the influence of emotional priming.

PubMed

Ashkenazi, Sarit

2018-02-05

Current theoretical approaches suggest that mathematical anxiety (MA) manifests itself as a weakness in quantity manipulations. This study is the first to examine automatic versus intentional processing of numerical information using the numerical Stroop paradigm in participants with high MA. To manipulate anxiety levels, we combined the numerical Stroop task with an affective priming paradigm. We took a group of college students with high MA and compared their performance to a group of participants with low MA. Under low anxiety conditions (neutral priming), participants with high MA showed relatively intact number processing abilities. However, under high anxiety conditions (mathematical priming), participants with high MA showed (1) higher processing of the non-numerical irrelevant information, which aligns with the theoretical view regarding deficits in selective attention in anxiety and (2) an abnormal numerical distance effect. These results demonstrate that abnormal, basic numerical processing in MA is context related.

Adaptive memory: the comparative value of survival processing.

PubMed

Nairne, James S; Pandeirada, Josefa N S; Thompson, Sarah R

2008-02-01

We recently proposed that human memory systems are "tuned" to remember information that is processed for survival, perhaps as a result of fitness advantages accrued in the ancestral past. This proposal was supported by experiments in which participants showed superior memory when words were rated for survival relevance, at least relative to when words received other forms of deep processing. The current experiments tested the mettle of survival memory by pitting survival processing against conditions that are universally accepted as producing excellent retention, including conditions in which participants rated words for imagery, pleasantness, and self-reference; participants also generated words, studied words with the intention of learning them, or rated words for relevance to a contextually rich (but non-survival-related) scenario. Survival processing yielded the best retention, which suggests that it may be one of the best encoding procedures yet discovered in the memory field.

The Dichotic Digits difference Test (DDdT): Development, Normative Data, and Test-Retest Reliability Studies Part 1.

PubMed

Cameron, Sharon; Glyde, Helen; Dillon, Harvey; Whitfield, Jessica; Seymour, John

2016-06-01

The dichotic digits test is one of the most widely used assessment tools for central auditory processing disorder. However, questions remain concerning the impact of cognitive factors on test results. To develop the Dichotic Digits difference Test (DDdT), an assessment tool that could differentiate children with cognitive deficits from children with genuine dichotic deficits based on differential test results. The DDdT consists of four subtests: dichotic free recall (FR), dichotic directed left ear (DLE), dichotic directed right ear (DRE), and diotic. Scores for six conditions are calculated (FR left ear [LE], FR right ear [RE], and FR total, as well as DLE, DRE, and diotic). Scores for four difference measures are also calculated: dichotic advantage, right-ear advantage (REA) FR, REA directed, and attention advantage. Experiment 1 involved development of the DDdT, including error rate analysis. Experiment 2 involved collection of normative and test-retest reliability data. Twenty adults (aged 25 yr 10 mo to 50 yr 7 mo, mean 36 yr 4 mo) took part in the development study; 62 normal-hearing, typically developing, primary-school children (aged 7 yr 1 mo to 11 yr 11 mo, mean 9 yr 4 mo) and 10 adults (aged 25 yr 0 mo to 51 yr 6 mo, mean 34 yr 10 mo) took part in the normative and test-retest reliability study. In Experiment 1, error rate analysis was conducted on the 36 digit-pair combinations of the DDdT. Normative data collected in Experiment 2 were arcsine transformed to achieve a distribution that was closer to a normal distribution and z-scores calculated. Pearson product-moment correlations were used to determine the strength of relationships between DDdT conditions. The development study revealed no significant differences in the adult population between test and retest on any DDdT condition. Error rates on 36 digit pairs ranged from 1.5% to 16.7%. The most and the least error-prone digits were removed before commencement of the normative data study, leaving 25 unique digit pairs. Average z-scores calculated from the arcsine-transformed data collected from the 62 children who took part in the normative data study revealed that FR dichotic processing (LE, RE, and total) was highly correlated with diotic processing (r ranging from 0.5 to 0.6; p < 0.0001). Significant improvements in performance on retest occurred for the FR LE, RE, total, and diotic conditions (p ranging from 0.05 to 0.0004), the conditions that would be expected to improve with practice if the participant's response strategies are better the second time around. The addition of a diotic control task-that shares many response demands with the usual dichotic tasks-opens up the possibility of differentiating children who perform below expectations because of poor dichotic processing skills from those who perform poorly because of impaired attention, memory, or other cognitive abilities. The high correlation between dichotic and diotic performance suggests that factors other than dichotic performance play a substantial role in a child's ability to perform a dichotic listening task. This hypothesis is investigated further in the cognitive correlation study that follows in the companion paper (DDdT Study Part 2; Cameron et al, 2016). American Academy of Audiology.

Investigation of UFO defect on DUV CAR and BARC process

NASA Astrophysics Data System (ADS)

Yet, Siew Ing; Ko, Bong Sang; Lee, Soo Man; May, Mike

2004-05-01

Photo process defect reduction is one of the most important factors to improve the process stability and yield in sub-0.18um DUV process. In this paper, a new approach to minimize the Deep-UV (DUV) Chemically Amplified Resist (CAR) and Bottom Anti-Reflective Coating (BARC) induced defect known as UFO (UnidentiFied Object) defect will be introduced. These defects have mild surface topography difference on BARC; it only exists on the wide exposed area where there is no photoresist pattern. In this test, Nikon KrF Stepper & Scanner and TEL Clean track were used. Investigation was carried out on the defect formulation on both Acetal and ESCAP type of photoresist while elemental analysis was done by Atomic Force Microscope (AFM) & Auger Electron Spectroscopy (AES). Result indicated that both BARC and photoresist induce this UFO defect; total defect quantity is related with Post Exposure Bake (PEB) condition. Based on the elemental analysis and process-split test, we can conclude that this defect is caused by lack of acid amount and low diffusivity which is related to PAG (Photo Acid Generator) and TAG (Thermal Acid Generator) in KrF photoresist and BARC material. By optimizing photoresist bake condition, this UFO defect as well as other related defect such as Satellite defect could be eliminated.

Design of an MR image processing module on an FPGA chip.

PubMed

Li, Limin; Wyrwicz, Alice M

2015-06-01

We describe the design and implementation of an image processing module on a single-chip Field-Programmable Gate Array (FPGA) for real-time image processing. We also demonstrate that through graphical coding the design work can be greatly simplified. The processing module is based on a 2D FFT core. Our design is distinguished from previously reported designs in two respects. No off-chip hardware resources are required, which increases portability of the core. Direct matrix transposition usually required for execution of 2D FFT is completely avoided using our newly-designed address generation unit, which saves considerable on-chip block RAMs and clock cycles. The image processing module was tested by reconstructing multi-slice MR images from both phantom and animal data. The tests on static data show that the processing module is capable of reconstructing 128×128 images at speed of 400 frames/second. The tests on simulated real-time streaming data demonstrate that the module works properly under the timing conditions necessary for MRI experiments. Copyright © 2015 Elsevier Inc. All rights reserved.

Modified glass fibre reinforced polymer composites

NASA Astrophysics Data System (ADS)

Cao, Yumei

A high ratio of strength to density and relatively low-cost are some of the significant features of glass fibre reinforced polymer composites (GFRPCs) that made them one of the most rapidly developed materials in recent years. They are widely used as the material of construction in the areas of aerospace, marine and everyday life, such as airplane, helicopter, boat, canoe, fishing rod, racket, etc. Traditionally, researchers tried to raise the mechanical properties and keep a high strength/weight ratio using all or some of the following methods: increasing the volume fraction of the fibre; using different polymeric matrix material; or changing the curing conditions. In recent years, some new techniques and processing methods were developed to further improve the mechanical properties of glass fibre (GF) reinforced polymer composite. For example, by modifying the surface condition of the GF, both the interface strength between the GF and the polymer matrix and the shear strength of the final composite can be significantly increased. Also, by prestressing the fibre during the curing process of the composite, the tensile, flexural and the impact properties of the composite can be greatly improved. In this research project, a new method of preparing GFRPCs, which combined several traditional and modern techniques together, was developed. This new method includes modification of the surface of the GF with silica particles, application of different levels of prestressing on the GF during the curing process, and the change of the fibre volume fraction and curing conditions in different sets of experiments. The results of the new processing were tested by the three-point bend test, the short beam shear test and the impact test to determine the new set of properties so formed in the composite material. Scanning electronic microscopy (SEM) was used to study the fracture surface of the new materials after the mechanical tests were performed. By taking advantages of the traditional and modern techniques at the same time, the newly developed modified glass fibre reinforced epoxy matrix composites (MGFRECs) have much improved comprehensive properties. The flexural strength, the flexural modulus, the shear modulus and the impact energy (Izod impact test) of the composites were improved up to 87%, 74%, 30% and 89% respectively when modified samples were compared to the samples made by the traditional methods.

Advanced treatment of residual nitrogen from biologically treated coke effluent by a microalga-mediated process using volatile fatty acids (VFAs) under stepwise mixotrophic conditions.

PubMed

Ryu, Byung-Gon; Kim, Woong; Heo, Sung-Woon; Kim, Donghyun; Choi, Gang-Guk; Yang, Ji-Won

2015-09-01

This work describes the development of a microalga-mediated process for simultaneous removal of residual ammonium nitrogen (NH4(+)-N) and production of lipids from biologically treated coke effluent. Four species of green algae were tested using a sequential mixotrophic process. In the first phase-CO2-supplied mixotrophic condition-all microalgae assimilated NH4(+)-N with no evident inhibition. In second phase-volatile fatty acids (VFAs)-supplied mixotrophic condition-removal rates of NH4(+)-N and biomass significantly increased. Among the microalgae used, Arctic Chlorella sp. ArM0029B had the highest rate of NH4(+)-N removal (0.97 mg/L/h) and fatty acid production (24.9 mg/L/d) which were 3.6- and 2.1-fold higher than those observed under the CO2-supplied mixotrophic condition. Redundancy analysis (RDA) indicated that acetate and butyrate were decisive factors for increasing NH4(+)-N removal and fatty acid production. These results demonstrate that microalgae can be used in a sequential process for treatment of residual nitrogen after initial treatment of activated sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Hydrometallurgical recovery of germanium from coal gasification fly ash: pilot plant scale evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arroyo, F.; Fernandez-Pereira, C.; Olivares, J.

2009-04-15

In this article, a hydrometallurgical method for the selective recovery of germanium from fly ash (FA) has been tested at pilot plant scale. The pilot plant flowsheet comprised a first stage of water leaching of FA, and a subsequent selective recovery of the germanium from the leachate by solvent extraction method. The solvent extraction method was based on Ge complexation with catechol in an aqueous solution followed by the extraction of the Ge-catechol complex (Ge(C{sub 6}H{sub 4}O{sub 2}){sub 3}{sup 2-}) with an extracting organic reagent (trioctylamine) diluted in an organic solvent (kerosene), followed by the subsequent stripping of the organicmore » extract. The process has been tested on a FA generated in an integrated gasification with combined cycle (IGCC) process. The paper describes the designed 5 kg/h pilot plant and the tests performed on it. Under the operational conditions tested, approximately 50% of germanium could be recovered from FA after a water extraction at room temperature. Regarding the solvent extraction method, the best operational conditions for obtaining a concentrated germanium-bearing solution practically free of impurities were as follows: extraction time equal to 20 min; aqueous phase/organic phase volumetric ratio equal to 5; stripping with 1 M NaOH, stripping time equal to 30 min, and stripping phase/organic phase volumetric ratio equal to 5. 95% of germanium were recovered from water leachates using those conditions.« less