Low-Maintenance Wind Power System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rasson, Joseph E

2010-09-30

Turbines of 1, 3 and 30 kW were designed, prototyped and evaluated. A 55 kW unit has been preliminarily designed. Two 1 kW alpha units and a 3 kW alpha unit were delivered to the US in 2005 and Empire Magnetics provided custom alternators for the units. After evaluation, the 6 bladed, 3 kW unit was chosen for beta fabrication and 5 units were delivered to the US in December, 2009 while others remained for testing in Russia.

Federal Guidance Report No. 4: Estimates and Evaluation of Fallout in the United States from Nuclear Weapons Testing Conducted Through 1962

EPA Pesticide Factsheets

This Federal Radiation Council report includes a full study and analysis of fallout expected in 1963 from nuclear testing that occurred in the past. This report covers fallout expected from Soviet and United States tests through 1962.

Multiple Hollow Cathode Wear Testing for the Space Station Plasma Contactor

NASA Technical Reports Server (NTRS)

Soulas, George C.

1994-01-01

A wear test of four hollow cathodes was conducted to resolve issues associated with the Space Station plasma contactor. The objectives of this test were to evaluate unit-to-unit dispersions, verify the transportability of contamination control protocols developed by the project, and to evaluate cathode contamination control and activation procedures to enable simplification of the gas feed system and heater power processor. These objectives were achieved by wear testing four cathodes concurrently to 2000 hours. Test results showed maximum unit-to-unit deviations for discharge voltages and cathode tip temperatures to be +/-3 percent and +/-2 percent, respectively, of the nominal values. Cathodes utilizing contamination control procedures known to increase cathode lifetime showed no trends in their monitored parameters that would indicate a possible failure, demonstrating that contamination control procedures had been successfully transferred. Comparisons of cathodes utilizing and not utilizing a purifier or simplified activation procedure showed similar behavior during wear testing and pre- and post-test performance characterizations. This behavior indicates that use of simplified cathode systems and procedures is consistent with long cathode lifetimes.

Evaluation of Aqua-Ammonia Chiller Technologies and Field Site Installation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zaltash, Abdolreza

2007-09-01

The Naval Facilities Engineering Service Center (NFESC) has sponsored Oak Ridge National Laboratory (ORNL) to review, select, and evaluate advanced, gas-fired, 5-ton, aqua-ammonia, chiller technologies. The selection criteria was that units have COP values of 0.67 or better at Air-conditioning and Refrigeration Institute (ARI) 95 F outdoor rating conditions, an active refrigerant flow control, and a variable-speed condenser fan. These features are expected to allow these units to operate at higher ambient temperatures (up to the maximum operating temperature of 110 F) with minimal degradation in performance. ORNL evaluated three potential manufacturers of advanced, gas-fired, 5-ton, aqua-ammonia chillers-Robur, Ambian, andmore » Cooling Technologies. Unfortunately, Robur did not meet the COP requirements and Cooling Technologies could not deliver a unit to be tested at the U.S. Department of Energy (DOE)-ORNL environmental chamber testing facility for thermally activated heat pumps. This eliminated these two technologies from further consideration, leaving only the Ambian chillers for evaluation. Two Ambian chillers were evaluated at the DOE-ORNL test facility. Overall these chillers operated well over a wide range of ambient conditions with minimal degradation in performance due to several control strategies used such as a variable speed condenser fan, a modulating burner, and active refrigerant flow control. These Ambian pre-commercial units were selected for installation and field testing at three federal facilities. NFESC worked with ORNL to assist with the site selection for installation and evaluation of these chillers. Two sites (ORNL and Naval Surface Warfare Center [NSWC] Corona) had a single chiller unit installed; and at one site (Naval Amphibious Base [NAB] Little Creek), two 5-ton chillers linked together were installed to provide 10 tons of cooling. A chiller link controller developed under this project was evaluated in the field test at Little Creek.« less

Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results

DTIC Science & Technology

1988-09-01

Test and Evaluation Report Test and Evaluation of the Navy Technical Information Presentation System (NTIPS) F-14A Field Test Results by .0 Joseph J...PROGRAM PROJECT TASK WORK UNIT Washington, D.C. 20361 ELEMENT NO. NO. NO. ACCESSION NO. OMN 1820 11. TITLE (Include Security Classification) TEST AND...EVALUATION OF THE NAVY TECHNICAL INFORMATION PRESENTATION SYSTEM (NTIPS) F-14A FIELD TEST RESULTS 12. PERSONAL AUTHOR(S) Fuller, Joseph F. (DTRC) Post

Geography Library of Test Items. Volume Four.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Home Science Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Smith, Jan, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection is reviewed for content validity and reliability. The test…

Languages Library of Test Items. Volume Two: German, Latin.

ERIC Educational Resources Information Center

Campbell, Thomas; And Others

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Languages Library of Test Items. Volume One: French, Indonesian.

ERIC Educational Resources Information Center

Campbell, Thomas; And Others

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Three.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Commerce Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Meeve, Brian, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Five.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Textiles and Design Library of Test Items. Volume I.

ERIC Educational Resources Information Center

Smith, Jan, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection is reviewed for content validity and reliability. The test…

Commerce Library of Test Items. Volume Two.

ERIC Educational Resources Information Center

Meeve, Brian, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume Six.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography: Library of Test Items. Volume II.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Geography Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

Detailed Test Plan Redundant Sensor Strapdown IMU Evaluation Program

NASA Technical Reports Server (NTRS)

Hartwell, T.; Miyatake, Y.; Wedekind, D. E.

1971-01-01

The test plan for a redundant sensor strapdown inertial measuring unit evaluation program is presented. The subjects discussed are: (1) test philosophy and limitations, (2) test sequence, (3) equipment specifications, (4) general operating procedures, (5) calibration procedures, (6) alignment test phase, and (7) navigation test phase. The data and analysis requirements are analyzed.

Laboratory evaluation of anti-biofilm agents for use in dental unit waterlines.

PubMed

Meiller, T F; Kelley, J I; Baqui, A A; DePaola, L G

2001-01-01

Dental unit waterline biofilm has been recognized as a potential point of contamination and a risk to patients with any level of immunocompromise. Biofilm in dental unit waterlines, once established, has proven formidable to efforts in disinfection/disruption. This project compared standardized evaluation techniques by assessing the efficacy of a variety of agents that have been reported or suggested as useful in surface disinfection and/or antiseptic protocols. The zones of inhibition, minimum inhibitory/bactericidal concentrations and use-dilution with stainless steel carrier replicates tests assessed the disinfection of planktonic organisms using standardized microbial testing procedures. The disruption and/or disinfection of planktonic and biofilm organisms within naturally occurring dental unit waterlines were evaluated by culture and scanning electron microscopy. The six commercially available antimicrobial agents used to assess the techniques were bleach (sodium hypochlorite), Cavicide, glutaraldehyde, Listerine Antiseptic, Peridex and Sterilex Ultra. Comparisons between the results for each technique evaluated were determined for each product. All six agents demonstrated antimicrobial efficacy at the working concentrations designated by the manufacturers. Biofilm matrix elimination evaluated by scanning electron microscopy found virtually 0% elimination by glutaraldehyde to an estimated 90% elimination by Sterilex Ultra and bleach after one treatment. Treatment with Cavicide, Listerine Antiseptic and Peridex resulted in negligible elimination of the biofilm matrix. For comparability, the use of standardized testing techniques to evaluate a disinfection agent's efficacy against dental unit waterline contamination is essential. This project demonstrates a model system for evaluating disinfection agents potentially useful in the management of dental unit waterline biofilm, and should assist in educating the dental clinician in the appraisal of existing and future product claims.

Effectiveness of Prepared Instruction Units in Teaching the Principles of Internal Combustion Engine Operation and Maintenance. Technical Bulletin No. 192.

ERIC Educational Resources Information Center

Jacobs, Clinton O.

The report is an evaluation of the effectiveness of the 12 instructional units developed around the use of the Briggs-Stratton Model 80302, 3HP, 8 cu. in. displacement engine having a fuel induction system similar in construction to farm tractor types. The evaluation procedure used was the "one-group Pre-test and Post-test" research method. The…

An information system to improve financial management, resource allocation and activity planning: evaluation results.

PubMed

Ruland, C M; Ravn, I H

2001-01-01

An important strategy for improving resource management and cost containment in health care is to develop information systems that assist hospital managers in financial management, resource allocation, and activity planning. A crucial part of such development is a rigorous evaluation to assess whether the system accomplishes it's intended goals. To evaluate CLASSICA, a Decision Support System (DSS), that assists nurse managers in financial management, resource allocation, staffing, and activity planning. Using a pre-post test design with control units, CLASSICA was evaluated in four test units. Baseline data and simultaneous parallel measures were collected prior to system implementation at test sites and control units. Using expense reports, staffing and financial statistics, surveys, interviews with nurse managers, and logs as data sources, CLASSICA was evaluated on: cost reduction, quality of management information; usefulness as decision support for improved financial management and decision-making; user satisfaction; and ease of use. Evaluation results showed a 41% reduction in expenditures for overtime and extra hours as compared to a 1.8% reduction in control units during the same time period. Users reported a significant improvement in management information; nurse managers stated that they had gained control over costs. The system helped them analyze the relationships between patient activity staffing, and cost of care. Users reported high satisfaction with the system, the information and decision support it provided, and its ease of use. These results suggest that CLASSICA is a DSS that successfully assists nurse managers in cost effective management of their units.

Science Library of Test Items. Volume Nineteen. A Collection of Multiple Choice Test Items Relating Mainly to Geology.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Seventeen. A Collection of Multiple Choice Test Items Relating Mainly to Biology.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Eighteen. A Collection of Multiple Choice Test Items Relating Mainly to Chemistry.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

TOXICITY TESTING, RISK ASSESSMENT, AND OPTIONS FOR DREDGED MATERIAL MANAGEMENT

EPA Science Inventory

Programs for evaluating proposed discharges of dredged material into waters of the United States specify a tiered testing and evaluation protocol that includes performance of acute and chronic bioassays to assess toxicity of the dredged sediments. Although these evaluations refl...

Evaluation of a new mobile system for protecting immune-suppressed patients against airborne contamination.

PubMed

Poirot, Jean-Louis; Gangneux, Jean-Pierre; Fischer, Alain; Malbernard, Mireille; Challier, Svetlana; Laudinet, Nicolas; Bergeron, Vance

2007-09-01

Invasive aspergillosis is one of the most lethal airborne dangers for immune-suppressed subjects. Providing patient protection from such airborne threats requires costly and high-maintenance facilities. We herein evaluate a new self-contained mobile unit as an alternative for creating a patient protective environment. Airborne contamination levels were monitored for different simulated scenarios and under actual clinical conditions. Functional tests were used to challenge the unit under adverse conditions, and a preliminary clinical study with patients and staff present was performed at 2 different French hospitals. Functional tests demonstrated that the unit can rapidly decontaminate air in the protected zone created by the unit and in the surrounding room. In addition, the protected zone is not sensitive to large disturbances that occur in the room. The clinical study included 4 patients with 150 accumulated days of testing. The protected zone created by the unit systematically provided an environment with undetectable airborne fungal levels (ie, <1 CFU/m(3)) regardless of the levels in the room or corridor (P < .01). These tests show that the unit can be used to create a mobile protective environment for immune-suppressed patients in a standard hospital setting.

Science Library of Test Items. Volume Twenty. A Collection of Multiple Choice Test Items Relating Mainly to Physics, 1.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Twenty-One. A Collection of Multiple Choice Test Items Relating Mainly to Physics, 2.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Science Library of Test Items. Volume Twenty-Two. A Collection of Multiple Choice Test Items Relating Mainly to Skills.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items are made available to teachers for the construction of unit tests or term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The test items meet syllabus…

Organizational Analysis of the United States Army Evaluation Center

DTIC Science & Technology

2014-12-01

analysis of qualitative or quantitative data obtained from design reviews, hardware inspections, M&S, hardware and software testing , metrics review... Research Development Test & Evaluation (RDT&E) appropriation account. The Defense Acquisition Portal ACQuipedia website describes RDT&E as “ one of the... research , design , development, test and evaluation, production, installation, operation, and maintenance; data collection; processing and analysis

Revision to dedicated short range communication roadside equipment specification – RSU 4.1.Bench Test Plan.

DOT National Transportation Integrated Search

2017-04-28

The document describes the overall process for evaluating Dedicated Short Range Communication (DSRC) Roadside Units (RSU) against USDOT RSU Specification 4.1 in preparation for field evaluation. The Test Cases contained in this document only evaluate...

Testing and evaluation of the subcarrier traffic information channel

DOT National Transportation Integrated Search

In support of the Federal Highway Administration of the United States Department : of Transportation, the Institute for Telecommunication Sciences has completed a : laboratory and field test program designed to independently evaluate the : performanc...

Turbopumps for cryogenic upper stage engines. [fabrication and evaluation of turbine pumps for liquid hydrogen and liquid oxygen

NASA Technical Reports Server (NTRS)

Zachary, A. T.; Csomor, A.; Tignac, L. L.

1973-01-01

Small, high-performance LO2 and LH2 turbopump assembly configurations were selected, detail designs were prepared and two of each unit were fabricated with each unit consisting of pump, turbine gas generator, and appropriate controls. Following fabrication, development testing was conducted on each type to demonstrate performance, durability, transient characteristics, and heat transfer under simulated altitude conditions. Following successful completion of development effort, the two LO2 turbopump units and one LH2 turbopump unit were acceptance tested as specified. Inspection of the units following development testing revealed no deleterious effects of testing. The test results of LO2 turbopump assembly testing correlated well with predicted performance while the LH2 turbopump test results, though generally consistent with predicted values, did show lower than anticipated developed head at the design point and in the high flow range of operation.

(De)Grading the Standardized Test: Can Standardized Testing Evaluate Schools?

ERIC Educational Resources Information Center

Simmons, Nicola E.

2004-01-01

Standardized testing is an assessment strategy that evaluates all students and all schools on the same basic skills and, therefore, might reasonably indicate which schools are high performers and which are not. Standardized testing is not a new strategy for providing this proof. The United States has produced reams of articles criticizing…

Termite testing continues

Treesearch

Terence L. Wagner; Joe Mulrooney; Chris Petereson

2002-01-01

The United States Department of Agriculture Forest Service's termiticide testing program provides unbiased efficacy data for product registration using standardized tests, sites and evaluation procedures. Virtually all termiticides undergo Forest Service tests prior to registration.

Evaluation of an LED (Light-Emitting Diode) high-mounted signal lamp

NASA Astrophysics Data System (ADS)

Olson, P. L.

1987-02-01

Two studies are described evaluating high-mounted stoplights using light-emitting diodes (LEDs) compared with conventional incandescent units. The first of these studies obtained ratings from subjects who drove one car and followed another car that was equipped with the test lamps. The results indicate that the subjects generally preferred the LEDs to the conventional lamp. The second study was a laboratory evaluation of the attention-getting capabilities of LED and incandescent stoplights. Under all conditions tested subjects responded faster to the LED units. The response time advantage for the LED units increased with more difficult viewing conditions, such as high levels of illumination and long viewing distance. The results of these investigations are discussed in terms of the applicability of the LED technology to high mounted stoplights on motor vehicles.

Minnesota urban partnership agreement national evaluation : exogenous factors test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the exogenous factors test plan for the national evaluation of the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reduc...

Minnesota urban partnership agreement national evaluation : transit system data test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the test plan for collecting and analyzing transit system data for the Minnesota Urban Partnership Agreement (UPA) National Evaluation under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA...

Minnesota urban partnership agreement national evaluation : surveys, interviews, and focus groups test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the test plan for developing, conducting, and analyzing surveys, interviews, and focus groups for evaluating the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Prog...

Evaluation of EDR-3 vibration, shock, temperature, and humidity recording unit

NASA Technical Reports Server (NTRS)

Rees, Kevin G.; Mondale, C. F.

1990-01-01

The purpose of this evaluation was to determine if the self-contained, off-the-shelf, Environmental Data Recorder 3 (EDR-3) could be qualified to monitor shock, vibration, and temperature during rail transportation of space shuttle solid rocket components. The evaluation testing started in November 1989 and continued until June 1990. Two EDR-3 units were used to monitor both on- and off-plant shipments of shuttle components. In addition, extensive testing was performed at Thiokol's Vibration Test facility, T-53. Testing demonstrated that the EDR-3 is capable of successfully monitoring actual shipments of solid rocket hardware. Thiokol metrology has verified the accuracy of temperature monitoring. In addition, calibrated shock/vibration testing demonstrated that the EDR-3 does accurately record acceleration. It is recommended that the vendor modify the EDR-3 data recovery system to allow remote communication via a 30-foot cable. This would permit communication with the unit mounted on a case segment after a rail car cover is installed. The vendor will make this change and produce a new model, designated EDR-3-10. It is further recommended that Thiokol qualify the EDR-3-10 for transportation monitoring of redesigned solid rocket motor (RSRM) components.

Situational and dispositional influences on nurses' workplace well-being: the role of empowering unit leadership.

PubMed

Spence Laschinger, Heather K; Finegan, Joan; Wilk, Piotr

2011-01-01

Unit-level leadership and structural empowerment play key roles in creating healthy work environments, yet few researchers have examined these contextual effects on nurses' well-being. The aim of this study was to test a multilevel model of structural empowerment examining the effect of nursing unit leadership quality and structural empowerment on nurses' experiences of burnout and job satisfaction and to examine the effect of a personal dispositional variable, core self-evaluation, on these nurse experiences. Nurses (n = 3,156) from 217 hospital units returned surveys that included measures of leader-member exchange, structural empowerment, burnout, core self-evaluation, and job satisfaction. Multilevel structural equation modeling was used to test the model. Nurses' shared perceptions of leader-member exchange quality on their units positively influenced their shared perceptions of unit structural empowerment (Level 2), which resulted in significantly higher levels of individual nurse job satisfaction (Level 1). Unit-level leader-member exchange quality also directly influenced individual nurse job satisfaction. Unit leader-member exchange quality and structural empowerment influenced emotional exhaustion and cynicism differentially. Higher unit-level leader-member exchange quality was associated with lower cynicism; higher unit-level structural empowerment was associated with lower emotional exhaustion. At Level 1, higher core self-evaluation was associated with lower levels of both emotional exhaustion and cynicism, both of which were associated with lower job satisfaction. This study provides a theoretical understanding of how unit leadership affects both unit- and individual-level outcomes.

Statistical modeling of dental unit water bacterial test kit performance.

PubMed

Cohen, Mark E; Harte, Jennifer A; Stone, Mark E; O'Connor, Karen H; Coen, Michael L; Cullum, Malford E

2007-01-01

While it is important to monitor dental water quality, it is unclear whether in-office test kits provide bacterial counts comparable to the gold standard method (R2A). Studies were conducted on specimens with known bacterial concentrations, and from dental units, to evaluate test kit accuracy across a range of bacterial types and loads. Colony forming units (CFU) were counted for samples from each source, using R2A and two types of test kits, and conformity to Poisson distribution expectations was evaluated. Poisson regression was used to test for effects of source and device, and to estimate rate ratios for kits relative to R2A. For all devices, distributions were Poisson for low CFU/mL when only beige-pigmented bacteria were considered. For higher counts, R2A remained Poisson, but kits exhibited over-dispersion. Both kits undercounted relative to R2A, but the degree of undercounting was reasonably stable. Kits did not grow pink-pigmented bacteria from dental-unit water identified as Methylobacterium rhodesianum. Only one of the test kits provided results with adequate reliability at higher bacterial concentrations. Undercount bias could be estimated for this device and used to adjust test kit results. Insensitivity to methylobacteria spp. is problematic.

Geography, Years 7-10, Library of Test Items. Volume Eight. Junior Secondary Items To Be Used With 1976 to 1980 H.S.C. Geography Exam. Broadsheets.

ERIC Educational Resources Information Center

Kouimanos, John, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from past tests are made available to teachers for the construction of unit tests, term examinations or as a basis for class discussion. Each collection was reviewed for content validity and reliability. The…

EVALUATION OF UTILITY BOILER RADIANT FURNACE RESIDENCE TIME/TEMPERATURE CHARACTERISTICS: FIELD TESTS AND HEAT TRANSFER MODELING

EPA Science Inventory

The report describes an investigation of the adequacy of a modeling approach in predicting the thermal environment and flow field of pulverized-coal-fired utility boilers. Two 420 MWe coal-fired boilers were evaluated: a single-wall-fired unit and a tangentially fired unit, repre...

Milliwatt Generator Project

NASA Astrophysics Data System (ADS)

Latimer, T. W.; Rinehart, G. H.

1992-05-01

This report covers progress on the Milliwatt Generator Project from April 1986 through March 1988. Activities included fuel processing and characterization, production of heat sources, fabrication of pressure-burst test units, compatibility studies, impact testing, and examination of surveillance units. The major task of the Los Alamos Milliwatt Generator Project is to fabricate MC2893A heat sources (4.0 W) for MC2730A radioisotope thermoelectric generators (RTG's) and MC3599 heat sources (4.5 W) for MC3500 RTG's. The MWG Project interfaces with the following contractors: Sandia National Laboratories, Albuquerque (designer); E.I. du Pont de Nemours and Co. (Inc.), Savannah River Plant (fuel); Monsanto Research Corporation, Mound Facility (metal hardware); and General Electric Company, Neutron Devices Department (RTG's). In addition to MWG fabrication activities, Los Alamos is involved in (1) fabrication of pressure-burst test units, (2) compatibility testing and evaluation, (3) examination of surveillance units, and (4) impact testing and subsequent examination of compatibility and surveillance units.

High Power Alternator Test Unit (ATU) Electrical System Test

NASA Technical Reports Server (NTRS)

Birchenough, Arthur; Hervol, David

2007-01-01

The Alternator Test Unit (ATU) in the Lunar Power System Facility (LPSF) located at the NASA Glenn Research Center (GRC) in Cleveland, OH was used to simulate the operating conditions and evaluate the performance of the ATU and it s interaction with various LPSF components in accordance with the JIMO AC Power System Requirements. The testing was carried out at the breadboard development level. Results of these tests will be used for the development and validation of analytical models for performance and lifetime prediction.

Integrated corridor management initiative : demonstration phase evaluation – Dallas corridor performance analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Corridor Performance Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM ...

Integrated corridor management initiative : demonstration phase evaluation – San Diego corridor performance analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Corridor Performance Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Integrated corridor management initiative : demonstration phase evaluation - Dallas decision support system analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Decision Support System (DSS) Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration....

Integrated corridor management initiative : demonstration phase evaluation – Dallas technical capability analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM ...

Operational Evaluation of VEGGIE Food Production System in the Habitat Demonstration Unit

NASA Technical Reports Server (NTRS)

Stutte, Gary W.; Newsham, Gerard; Morrow, Robert M.; Wheeler, Raymond M.

2011-01-01

The 2010 Desert Research and Technology Studies (DRATS) of the VEGGIE Food Production System in the Habitat Demonstration Unit (HDU) Pressurized Excursion Module (PEM) was the first operational evaluation of salad crop production technology in a NASA analog test. A systematic evaluation of rooting media and nutrient delivery systems were evaluated for three lettuce cultivars that have shown promise as candidates for a surface based food production system. The VEGGIE nutrient delivery system worked well, was able to be maintained by multiple operators with a minimum of training, and supported excellent lettuce growth for the duration of the test. A Hazard Analysis and Critical Control Point (HACCP) evaluation was performed using ProSan(tm) as sanitation agent prior to consumption was approved, and the crew was allowed to consume the lettuce grown using the VEGGIE light cap and gravity based nutrient delivery system at the completion of the 14-day DRAT field test. The DRAT field test validated the crew operations; Growth of all lettuce cultivars was excellent. The operational DRAT field testing in the HDU identified light quality issues related to morphology and pigment development that will need to be addressed through additional testing. Feedback from the crew, ground support personnel, and human factors leads was uniformly positive on the psychological value of having the crop production system in the excursion module. A number of areas have been identified for future work, to minimize the "footprint" of the Food Production system through creative use of unused wall and floor space in the unit.

Operation Evaluation of the VEGGIE Food Production System in the Habitat Demonstration Unit

NASA Technical Reports Server (NTRS)

Stutte, Gary W.; Newsham, Gerard; Morrow, Robert M.; Wheeler, Raymond M.

2011-01-01

The 2010 Desert Research and Technology Studies (DRATS) of the VEGGIE Food Production System in the Habitat Demonstration Unit (HDU) Pressurized Excursion Module (PEM) was the first operational evaluation of salad crop production technology in a NASA analog test. A systematic evaluation of rooting media and nutrient delivery systems were evaluated for three lettuce cultivars that have shown promise as candidates for a surface based food production system. The VEGGIE nutrient delivery system worked well, was able to be maintained by multiple operators with a minimum of training, and supported excellent lettuce growth for the duration of the test. A Hazard Analysis and Critical Control Point (HACCP) evaluation was performed using ProSantm as sanitation agent prior to consumption was approved, and the crew was allowed to consume the lettuce grown using the VEGGIE light cap and gravity based nutrient delivery system at the completion of the 14-day DRAT field test. The DRAT field test validated the crew operations; Growth of all lettuce cultivars was excellent. The operational DRAT field testing in the HDU identified light quality issues related to morphology and pigment development that will need to be addressed through additional testing. Feedback from the crew, ground support personnel, and human factors leads was uniformly positive on the psychological value of having the crop production system in the excursion module. A number of areas have been identified for future work, to minimize the "footprint" of the Food Production system through creative use of unused wall and floor space in the unit.

The final days of Solar Max - Lessons learned from engineering evaluation tests

NASA Technical Reports Server (NTRS)

Donnelly, Michael L.; Croft, John W.; Ward, David K.; Thames, Michael A.

1990-01-01

End-of-life engineering evaluation tests were performed on Solar Max between October and November 1989. The tests included four-wheel control law operation; reaction wheel rundowns; modular power subsystem standard power regulator unit voltage-temperature level tests; battery rundown/2nd plateau determination; high gain antenna retraction and jettison; and solar array jettison. This paper presents these tests, their results, and the lessons learned from them.

MOBILE ON-SITE RECYCLING OF METALWORKING FLUIDS

EPA Science Inventory

Product quality, waste reduction, and economic issues were evaluated for a technology designed to recycle metalworking fluids. mulsion-type fluids were tested at two sites and a synthetic fluid was tested at a third site. he specific recycling unit evaluated is based on the techn...

Integrated corridor management initiative : demonstration phase evaluation – San Diego benefit-cost analysis test plan.

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Benefit-Cost Analysis (BCA) for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM project...

The 5000 GPM firefighting module evaluation test

NASA Technical Reports Server (NTRS)

Burns, Ralph A.

1986-01-01

The 5000 GPM Firefighting Module development was sponsored and shared by the Navy Facilities Engineering Command. It is a lightweight, compact, self-contained, helicopter-transportable unit for fighting harbor and other specialty fires as well as for use in emergency and shipboard water pumping applications. This unit is a more advanced model of the original 1500 GPM module developed for the U.S. Coast Guard. The module and an evaluation test program conducted at the North Island Naval Air Station, San Diego, California, by NASA and the U.S. Navy, are described.

Test and evaluation of load converter topologies used in the Space Station Freedom Power Management and distribution DC test bed

NASA Technical Reports Server (NTRS)

Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

1991-01-01

Power components hardware in support of the Space Station Freedom dc Electrical Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switchmode converter, and a switching full-bridge forward converter. The topology, operation principles, and tests results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

Joining the Conversation: Predictors of Success on the United States Medical Licensing Examinations (USMLE)

ERIC Educational Resources Information Center

Gohara, Sabry; Shapiro, Joseph I.; Jacob, Adam N.; Khuder, Sadik A.; Gandy, Robyn A.; Metting, Patricia J.; Gold, Jeffrey; Kleshinski, James; and James Kleshinski

2011-01-01

The purpose of this study was to evaluate whether models based on pre-admission testing, including performance on the Medical College Admission Test (MCAT), performance on required courses in the medical school curriculum, or a combination of both could accurately predict performance of medical students on the United States Medical Licensing…

The United States Army Logistics Center Historical Summary. (RCS-HIS-6 (R2)). 1 October 1976 to 30 September 1978.

DTIC Science & Technology

1980-01-10

Experimentation (FDTE) 138 Corps Automation Requirements Baseline Identification Test (CARBIT) 138 Division Materiel Management Center (DMMC) 139 Concept...Evaluation Programs (CEP) 139 Test Design and Evaluation 140 Test and Evaluation Milestone Management System (TEMMS) 140 Manpower Analysis/Force...System (CS3) Maintenance Reporting and Management (MRM) 153 DA - Standard Port System (DASPS) 154 DA - Standard Port System - Enhancement (DASPS-E) 155 DA

Efficacy of anti-retraction devices in preventing bacterial contamination of dental unit water lines.

PubMed

Berlutti, Francesca; Testarelli, Luca; Vaia, Francesco; De Luca, Massimo; Dolci, Giovanni

2003-02-01

In this study we examine the efficacy of anti-retraction devices in preventing microbial contamination of dental unit water lines (DUWLs). The study was performed on 54 randomly selected DUs in use at private and public institutions for over six months. The selected DUs were all currently commercially available. To evaluate the efficiency of anti-retraction devices, two different methods were employed, mechanical and microbiological. The ADA/ANSI specification #47 (corresponding to a water retraction of less than 40.3 microl) was used for the evaluation of the retraction determined using the mechanical method; the presence/absence of test microorganisms in DUWLs upstream the turbine after the test was used for evaluating the microbiological assay. Both evaluation methods indicated correct amounts of retraction and prevention of DUWL contamination occurred in only two cases (3.7%). Correct retraction was noted in six other dental units (DUs), but their DUWLs became contaminated during testing. Six other produced the opposite results-improper retraction, yet no contamination. The remaining 40 DUs (74.0%) failed both evaluations. The results showed that the overwhelming majority of the anti-retraction devices did not prevent retraction when the turbine stopped running, leading to a contamination of the water lines, and to a consequent possible cross-contamination of the patients.

Superfund Technology Evaluation Report: SITE Program Demonstration Test Shirco Pilot-Scale Infrared Incineration System at the Rose Township Demode Road Superfund Site Volume I

EPA Science Inventory

The Shirco Pilot-Scale Infrared Incineration System was evaluated during a series of seventeen test runs under varied operating conditions at the Demode Road Superfund Site located in Rose Township, Michigan. The tests sought to demonstrate the effectiveness of the unit and the t...

Laboratory Performance Evaluation Report of SEL 421 Phasor Measurement Unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Zhenyu; faris, Anthony J.; Martin, Kenneth E.

2007-12-01

PNNL and BPA have been in close collaboration on laboratory performance evaluation of phasor measurement units for over ten years. A series of evaluation tests are designed to confirm accuracy and determine measurement performance under a variety of conditions that may be encountered in actual use. Ultimately the testing conducted should provide parameters that can be used to adjust all measurements to a standardized basis. These tests are performed with a standard relay test set using recorded files of precisely generated test signals. The test set provides test signals at a level and in a format suitable for input tomore » a PMU that accurately reproduces the signals in both signal amplitude and timing. Test set outputs are checked to confirm the accuracy of the output signal. The recorded signals include both current and voltage waveforms and a digital timing track used to relate the PMU measured value with the test signal. Test signals include steady-state waveforms to test amplitude, phase, and frequency accuracy, modulated signals to determine measurement and rejection bands, and step tests to determine timing and response accuracy. Additional tests are included as necessary to fully describe the PMU operation. Testing is done with a BPA phasor data concentrator (PDC) which provides communication support and monitors data input for dropouts and data errors.« less

Thematic mapper flight model preshipment review data package. Volume 4: Appendix. Part E: Electronics module data

NASA Technical Reports Server (NTRS)

1982-01-01

Tests to verify the as-designed performance of all circuits within the thematic mapper electronics module unit are described. Specifically, the tests involved the evaluation of the scan line corrector driver, shutter drivers function, cal lamp controller function, post amplifier function, command decoder verification unit, and the temperature and actuator controllers function.

Mobile HIV screening in Cape Town, South Africa: clinical impact, cost and cost-effectiveness.

PubMed

Bassett, Ingrid V; Govindasamy, Darshini; Erlwanger, Alison S; Hyle, Emily P; Kranzer, Katharina; van Schaik, Nienke; Noubary, Farzad; Paltiel, A David; Wood, Robin; Walensky, Rochelle P; Losina, Elena; Bekker, Linda-Gail; Freedberg, Kenneth A

2014-01-01

Mobile HIV screening may facilitate early HIV diagnosis. Our objective was to examine the cost-effectiveness of adding a mobile screening unit to current medical facility-based HIV testing in Cape Town, South Africa. We used the Cost Effectiveness of Preventing AIDS Complications International (CEPAC-I) computer simulation model to evaluate two HIV screening strategies in Cape Town: 1) medical facility-based testing (the current standard of care) and 2) addition of a mobile HIV-testing unit intervention in the same community. Baseline input parameters were derived from a Cape Town-based mobile unit that tested 18,870 individuals over 2 years: prevalence of previously undiagnosed HIV (6.6%), mean CD4 count at diagnosis (males 423/µL, females 516/µL), CD4 count-dependent linkage to care rates (males 31%-58%, females 49%-58%), mobile unit intervention cost (includes acquisition, operation and HIV test costs, $29.30 per negative result and $31.30 per positive result). We conducted extensive sensitivity analyses to evaluate input uncertainty. Model outcomes included site of HIV diagnosis, life expectancy, medical costs, and the incremental cost-effectiveness ratio (ICER) of the intervention compared to medical facility-based testing. We considered the intervention to be "very cost-effective" when the ICER was less than South Africa's annual per capita Gross Domestic Product (GDP) ($8,200 in 2012). We projected that, with medical facility-based testing, the discounted (undiscounted) HIV-infected population life expectancy was 132.2 (197.7) months; this increased to 140.7 (211.7) months with the addition of the mobile unit. The ICER for the mobile unit was $2,400/year of life saved (YLS). Results were most sensitive to the previously undiagnosed HIV prevalence, linkage to care rates, and frequency of HIV testing at medical facilities. The addition of mobile HIV screening to current testing programs can improve survival and be very cost-effective in South Africa and other resource-limited settings, and should be a priority.

Test and evaluation of load converter topologies used in the Space Station Freedom power management and distribution dc test bed

NASA Technical Reports Server (NTRS)

Lebron, Ramon C.; Oliver, Angela C.; Bodi, Robert F.

1991-01-01

Power components hardware in support of the Space Station freedom dc Electric Power System were tested. One type of breadboard hardware tested is the dc Load Converter Unit, which constitutes the power interface between the electric power system and the actual load. These units are dc to dc converters that provide the final system regulation before power is delivered to the load. Three load converters were tested: a series resonant converter, a series inductor switch-mode converter, and a switching full-bridge forward converter. The topology, operation principles, and test results are described, in general. A comparative analysis of the three units is given with respect to efficiency, regulation, short circuit behavior (protection), and transient characteristics.

Un Test contrastif oral pour l'evaluation des difficultes lexicales dans l'apprentissage de l'anglais L2 (An Oral Contrastive Test for the Evaluation of Lexical Difficulties in Learning English as a Second Language).

ERIC Educational Resources Information Center

Haeusser, Christiane

1978-01-01

The test described here is a particular type of diagnostic test; it is part of a series of tests designed to explore systematically areas of potential lexical difficulty in the English language for French-speaking students of English. The lexical units are considered under their formal, morphological, syntactic and semantic aspects. The test has…

Overcoming nursing barriers to intensive care unit early mobilisation: A quality improvement project.

PubMed

Hunter, Oluwatobi O; George, Elisabeth L; Ren, Dianxu; Morgan, Douglas; Rosenzweig, Margaret; Klinefelter Tuite, Patricia

2017-06-01

To increase adherence with intensive care unit mobility by developing and implementing a mobility training program that addresses nursing barriers to early mobilisation. An intensive care unit mobility training program was developed, implemented and evaluated with a pre-test, immediate post-test and eight-week post-test. Patient mobility was tracked before and after training. A ten bed cardiac intensive care unit. The training program's efficacy was measured by comparing pre-test, immediate post-test and 8-week post-test scores. Patient mobilisation rates before and after training were compared. Protocol compliance was measured in the post training group. Nursing knowledge increased from pre-test to immediate post-test (p<0.0001) and pre-test to 8-week post-test (p<0.0001). Mean test scores decreased by seven points from immediate post-test (80±12) to 8-week post-test (73±14). Fear significantly decreased from pre-test to immediate post-test (p=0.03), but not from pre-test to 8-week post-test (p=0.06) or immediate post-test to 8-week post-test (p=0.46). Post training patient mobility rates increased although not significantly (p=0.07). Post training protocol compliance was 78%. The project successfully increased adherence with intensive care unit mobility and indicates that a training program could improve adoption of early mobility. Copyright © 2016 Elsevier Ltd. All rights reserved.

Test and Evaluation Management Guide

DTIC Science & Technology

1993-08-01

between Ser- biotoxicity . Chemical-mixing tests are con- vice and DOE test personnel (Reference ducted to obtain information on the binary 55). chemical...reaction. Biotoxicity tests are per- formed to assess the potency of the agent Since the United States signed and ratified generated. Chemical weapons

Effect of bionic coupling units' forms on wear resistance of gray cast iron under dry linear reciprocating sliding condition

NASA Astrophysics Data System (ADS)

Pang, Zuobo; Zhou, Hong; Xie, Guofeng; Cong, Dalong; Meng, Chao; Ren, Luquan

2015-07-01

In order to get close to the wear form of guide rails, the homemade linear reciprocating wear testing machine was used for the wear test. In order to improve the wear-resistance of gray cast iron guide rail, bionic coupling units of different forms were manufactured by a laser. Wear behavior of gray-cast-iron with bionic-coupling units has been studied under dry sliding condition at room temperature using the wear testing machine. The wear resistance was evaluated by means of weight loss measurement and wear morphology. The results indicated that bionic coupling unit could improve the wear resistance of gray cast iron. The wear resistance of gray cast iron with reticulation bionic coupling unit is the best. When the load and speed changed, reticulation bionic coupling unit still has excellent performance in improving the wear resistance of gray cast iron.

Testing the Birth Unit Design Spatial Evaluation Tool (BUDSET) in Australia: a pilot study.

PubMed

Foureur, Maralyn J; Leap, Nicky; Davis, Deborah L; Forbes, Ian F; Homer, Caroline E S

2011-01-01

To pilot test the Birth Unit Design Spatial Evaluation Tool (BUDSET) in an Australian maternity care setting to determine whether such an instrument can measure the optimality of different birth settings. Optimally designed spaces to give birth are likely to influence a woman's ability to experience physiologically normal labor and birth. This is important in the current industrialized environment, where increased caesarean section rates are causing concerns. The measurement of an optimal birth space is currently impossible, because there are limited tools available. A quantitative study was undertaken to pilot test the discriminant ability of the BUDSET in eight maternity units in New South Wales, Australia. Five auditors trained in the use of the BUDSET assessed the birth units using the BUDSET, which is based on 18 design principles and is divided into four domains (Fear Cascade, Facility, Aesthetics, and Support) with three to eight assessable items in each. Data were independently collected in eight birth units. Values for each of the domains were aggregated to provide an overall Optimality Score for each birth unit. A range of Optimality Scores was derived for each of the birth units (from 51 to 77 out of a possible 100 points). The BUDSET identified units with low-scoring domains. Essentially these were older units and conventional labor ward settings. The BUDSET provides a way to assess the optimality of birth units and determine which domain areas may need improvement. There is potential for improvements to existing birth spaces, and considerable improvement can be made with simple low-cost modifications. Further research is needed to validate the tool.

Fractionated analysis of paired-electrode nerve recordings.

PubMed

Fiore, Lorenzo; Lorenzetti, Walter; Ratti, Giovannino; Geppetti, Laura

2003-12-30

Multi-unit activity recorded from two electrodes positioned at a distance on a nerve may be analysed by cross-correlation, but units similar in direction and velocity of propagation cannot be distinguished and separately evaluated by this method. To overcome this limit, we added two features, represented by the impulse amplitudes of the paired recordings, to the dimension given by the impulse delay. The analysis was fractionated according to the new dimensions. In experimental recordings from the locomotor appendage of the lobster Homarus americanus, the fractionated analysis proved capable of identifying the contributions of single active units, even if these were superimposed and indiscernible in the global cross-correlation histogram. Up to 5 motor and 10 sensory units could be identified. The shape of the paired impulses was evaluated by an averaging procedure. Analogous evaluations on simulated recordings made it possible to estimate the influences exerted on performance by variations in noise level and in the number and firing rate of active units. The global signal could be resolved into single units even under the worst conditions. Accuracy in evaluating the amount of unit activity varied, exceeding 90% in about half of the cases tested; a similar performance was attained by evaluation of the impulse shapes.

Item analysis of three Spanish naming tests: a cross-cultural investigation.

PubMed

Marquez de la Plata, Carlos; Arango-Lasprilla, Juan Carlos; Alegret, Montse; Moreno, Alexander; Tárraga, Luis; Lara, Mar; Hewlitt, Margaret; Hynan, Linda; Cullum, C Munro

2009-01-01

Neuropsychological evaluations conducted in the United States and abroad commonly include the use of tests translated from English to Spanish. The use of translated naming tests for evaluating predominately Spanish-speakers has recently been challenged on the grounds that translating test items may compromise a test's construct validity. The Texas Spanish Naming Test (TNT) has been developed in Spanish specifically for use with Spanish-speakers; however, it is unlikely patients from diverse Spanish-speaking geographical regions will perform uniformly on a naming test. The present study evaluated and compared the internal consistency and patterns of item-difficulty and -discrimination for the TNT and two commonly used translated naming tests in three countries (i.e., United States, Colombia, Spain). Two hundred fifty two subjects (136 demented, 116 nondemented) across three countries were administered the TNT, Modified Boston Naming Test-Spanish, and the naming subtest from the CERAD. The TNT demonstrated superior internal consistency to its counterparts, a superior item difficulty pattern than the CERAD naming test, and a superior item discrimination pattern than the MBNT-S across countries. Overall, all three Spanish naming tests differentiated nondemented and moderately demented individuals, but the results suggest the items of the TNT are most appropriate to use with Spanish-speakers. Preliminary normative data for the three tests examined in each country are provided.

Integrated Evaluation of Closed Loop Air Revitalization System Components

NASA Technical Reports Server (NTRS)

Murdock, K.

2010-01-01

NASA s vision and mission statements include an emphasis on human exploration of space, which requires environmental control and life support technologies. This Contractor Report (CR) describes the development and evaluation of an Air Revitalization System, modeling and simulation of the components, and integrated hardware testing with the goal of better understanding the inherent capabilities and limitations of this closed loop system. Major components integrated and tested included a 4-Bed Modular Sieve, Mechanical Compressor Engineering Development Unit, Temperature Swing Adsorption Compressor, and a Sabatier Engineering and Development Unit. The requisite methodolgy and technical results are contained in this CR.

Remote sensing of physiographic soil units of Bennett County, South Dakota

NASA Technical Reports Server (NTRS)

Frazee, C. J.; Gropper, J. L.; Westin, F. C.

1973-01-01

A study was conducted in Bennett County, South Dakota, to establish a rangeland test site for evaluating the usefulness of ERTS data for mapping soil resources in rangeland areas. Photographic imagery obtained in October, 1970, was analyzed to determine which type of imagery is best for mapping drainage and land use patterns. Imagery of scales ranging from 1:1,000,000 to 1.20,000 was used to delineate soil-vegetative physiographic units. The photo characteristics used to define physiographic units were texture, drainage pattern, tone pattern, land use pattern and tone. These units will be used as test data for evaluating ERTS data. The physiographic units were categorized into a land classification system. The various categories which were delineated at the different scales of imagery were designed to be useful for different levels of land use planning. The land systems are adequate only for planning of large areas for general uses. The lowest category separated was the facet. The facets have a definite soil composition and represent different soil landscapes. These units are thought to be useful for providing natural resource information needed for local planning.

An Analysis of Test And Evaluation in Rapid Acquisition Programs

DTIC Science & Technology

2015-12-01

program manager is assigned the requirement and allocated resources to carry out with an acquisition plan. 2. Role of Test and Evaluation Test and...Manual, verify the Maintenance Allocation Chart, and ensure the completeness of the System Support Package. The Maintainability Demonstration measured...additional outside personnel that require additional logistics support, such as security, facilitates, and berthing placing additional strain on units. CLS

Flight test and evaluation of Omega navigation in a general aviation aircraft. Volume 2: Appendices

NASA Technical Reports Server (NTRS)

Howell, J. D.; Hoffman, W. C.; Hwoschinsky, P. V.; Wischmeyer, C. E.

1975-01-01

Detailed documentation for each flight of the Omega Flight Evaluation study is presented, including flight test description sheets and actual flight data plots. Computer programs used for data processing and flight planning are explained and the data formats utilized by the Custom Interface Unit are summarized.

30 CFR 7.67 - Construction test.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Construction test. 7.67 Section 7.67 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Multiple-Shot Blasting Units § 7.67 Construction test...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giovanni, D.V.; Carr, R.C.; Landham, E.C.

Two products of coal quality research at the Electric Power Research Institute TM (EPRI) are available for field evaluation: Coal Quality Impact Model (CQIM and Fireside Testing Guidelines (FIG). The CQIM is a computer program that may be tailored to simulate the performance characteristics of a coal-fired power plant. The FIG is a technical report that guides utilities in conducting field tests to gather performance data and quantify the technical and economic impacts of different coals. Moreover, the results from field tests may be utilized to validate and assess the applicability of the CQIM. Field tests were conducted at Mississippimore » Power Company`s Watson Unit 4 to evaluate the coal quality impacts of coal switching on boiler performance and emissions. Watson Unit 4 is a 255 MW (gross), opposed-wall, pulverized-coal-fired boiler manufactured by Riley Stoker Corporation and rated at 1,779,000 lb/hr steam flow at 1000{degrees}F superheat steam temperature and 2,500 psig. The unit is equipped with a cold-side electrostatic precipitator for particulate matter control. Comprehensive tests were conducted on all major equipment components, including the pulverizers, fans, combustion equipment, boiler heat transfer surfaces, air preheater, and electrostatic precipitator, for two coals. The CQIN4 was configured to predict the performance of the unit when burning each coal. The work was sponsored by EPRI, and Mississippi Power Company (MPC) was the host utility company. This report summarizes results from the field test program, including potential heat rate improvements that were identified, and the differences in unit operations and performance for the two coals. The results from the CQIM validation effort are also presented.« less

Total Agent per Liter of Air With Particle Size Distribution (TALAp): A New Unit of Measure for the Test and Evaluation of Biodetectors

DTIC Science & Technology

2010-09-01

SAIC. He received a doctor of philosophy degree in microbiology from Utah State University. Dr. Mohr was the division chief of the DoD Life Sciences Test...Previously, she held internships at Amnesty International and the United Nations and was an intelligence analyst for the U.S. Army National Guard. E

Research review of potential safety effects of electronic billboards on driver attention and distraction

DOT National Transportation Integrated Search

1998-03-01

The Strategic Highway Research Program developed and coordinated construction of test sections for flexible pavement maintenance throughout the United States and Canada. Test sites included specific test sections for evaluation of the performance of ...

Rapid test methods for the evaluation of concrete properties.

DOT National Transportation Integrated Search

1982-01-01

The objective of the project was to place a CERL/Kelly-Vail testing unit and a microwave oven in the field to perform tests of plastic concrete on construction projects. : The CERL/K-V tests were to determine water and cement content of the concrete ...

Evaluation of the 8310-N-S manufactured by Sutron–Results of bench, temperature, and field deployment testing

USGS Publications Warehouse

Kunkle, Gerald A.

2016-01-07

The Sutron 8310-N-S (8310) data collection platform (DCP) manufactured by Sutron Corporation was evaluated by the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF) for conformance to the manufacturer’s specifications for recording and transmitting data. The 8310-N-S is a National Electrical Manufacturers Association (NEMA)-enclosed DCP with a built-in Geostationary Operational Environmental Satellite transmitter that operates over a temperature range of −40 to 60 degrees Celsius (°C). The evaluation procedures followed and the results obtained are described in this report for bench, temperature chamber, and outdoor deployment testing. The three units tested met the manufacturer’s stated specifications for the tested conditions, but two of the units had transmission errors either during temperature chamber or deployment testing. During outdoor deployment testing, 6.72 percent of transmissions by serial number 1206109 contained errors, resulting in missing data. Transmission errors were also observed during temperature chamber testing with serial number 1208283, at an error rate of 3.22 percent. Overall, the 8310 has good logging capabilities, but the transmission errors are a concern for users who require reliable telemetered data.

Evaluation of effect of different disposable infection control barriers on light intensity of light-curing unit and microhardness of composite - An in vitro study.

PubMed

Khode, Rajiv Tarachand; Shenoi, Pratima Ramakrishna; Kubde, Rajesh R; Makade, Chetana S; Wadekar, Kanchan D; Khode, Priyanka Tarachand

2017-01-01

This study evaluated effect of infection control barriers on light intensity (LI) of light-curing unit (LCU) and microhardness of composite. Four different disposable barriers ( n = 30) were tested against the control. LI for each barrier was measured with Lux meter. One hundred and fifty Teflon molds were equally divided into five groups of thirty each. Composite was filled in bulk in these molds and cured without and with barrier. Microhardness was evaluated on top and bottom surface of composite specimen with microhardness testing machine and hardness ratio (HR) was derived. One-way analysis of variance, Tukey's honestly significant difference test, and paired t -test using SPSS version 18 software. All barriers had significantly reduced the baseline LI of LCU ( P < 0.0001), but only Cure Elastic Steri-Shield and latex cut glove pieces (LCGP) significantly reduced the microhardness of the composite ( P < 0.05). However, HR determined inadequate curing only with LCGP. Although entire tested barrier significantly reduced the LI; none, except LCGP markedly affected the degree of cure of the composite.

Liquid disinfecting and sterilization reprocessors used for flexible endoscopes.

PubMed

1994-06-01

In this issue, we evaluate three liquid disinfecting flexible endoscope reprocessors that can be used with a user-supplied liquid chemical germicide (LCG), primarily for high-level disinfection (HLD). Applying most of the same criteria and test methods, we also evaluated a fourth unit, presented separately, that is marketed as a liquid sterilizing reprocessor and must be used with manufacturer-supplied, single-use containers of LCG. Although the sterilizing unit can be used for rigid endoscopes, surgical instruments, and endoscopic accessories, we evaluated its application to the reprocessing of only flexible endoscopes. Our ratings are based on the following: (1) basic performance, such as compatibility with several different types of endoscopes and LCGs, inclusion of all essential reprocessing phases, and exposure of all endoscope surfaces to the LCG and rinse water; (2) safety, such as ensuring that essential reprocessing phases cannot be skipped or omitted, that personnel exposure to LCG vapors is minimized, and that the reprocessor is unlikely to contaminate the endoscope during reprocessing; and (3) human factors design, such as ease of use and installation. We did not perform microbiological testing to confirm HLD or sterilization by any of the evaluated reprocessors because, with a suitably clean endoscope that is in good condition, no evidence indicates that the LCGs used would not be effective on the surfaces that they contact; also, the results would be unique to the two flexible endoscopes that we used for our testing. We rated all four reprocessors Conditionally Acceptable. The units are Acceptable on the condition that users understand that they cannot be used to process the elevator cable channel of side-viewing duodenoscopes; additional conditions apply only to the liquid disinfecting units. However, if the conditions are met, all four units reduce the likelihood of using a contaminated endoscope on a patient and reduce personnel exposure to the LCG. Selection of a unit will be based on the needs and preferences of the individual healthcare facility. Our ratings also assume that these units will be used according to the manufacturers' instructions and the endoscope's operator's manual. Note that, although the evaluated liquid disinfecting units provide detergent-flushing, post-detergent water-rinse, and post-detergent water-rinse-removal phases, manual cleaning of endoscopes before automatic reprocessing is essential, regardless of which reprocessor is used.

Decreasing airborne contamination levels in high-risk hospital areas using a novel mobile air-treatment unit.

PubMed

Bergeron, V; Reboux, G; Poirot, J L; Laudinet, N

2007-10-01

To evaluate the performance of a new mobile air-treatment unit that uses nonthermal-plasma reactors for lowering the airborne bioburden in critical hospital environments and reducing the risk of nosocomial infection due to opportunistic airborne pathogens, such as Aspergillus fumigatus. Tests were conducted in 2 different high-risk hospital areas: an operating room under simulated conditions and rooms hosting patients in a pediatric hematology ward. Operating room testing provided performance evaluations of removal rates for airborne contamination (ie, particles larger than 0.5 microm) and overall lowering of the airborne bioburden (ie, colony-forming units of total mesophilic flora and fungal flora per cubic meter of air). In the hematology service, opportunistic and nonpathogenic airborne fungal levels in a patient's room equipped with an air-treatment unit were compared to those in a control room. In an operating room with a volume of 118 m(3), the time required to lower the concentration of airborne particles larger than 0.5 microm by 90% was decreased from 12 minutes with the existing high-efficiency particulate air filtration system to less than 2 minutes with the units tested, with a 2-log decrease in the steady-state levels of such particles (P<.01). Concurrently, total airborne mesophilic flora concentrations dropped by a factor of 2, and the concentrations of fungal species were reduced to undetectable levels (P<.01). The 12-day test period in the hematology ward revealed a significant reduction in airborne fungus levels (P<.01), with average reductions of 75% for opportunistic species and 82% for nonpathogenic species. Our data indicate that the mobile, nonthermal-plasma air treatment unit tested in this study can rapidly reduce the levels of airborne particles and significantly lower the airborne bioburden in high-risk hospital environments.

Development of a Fan-Filter Unit Test Standard, LaboratoryValidations, and its Applications across Industries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Tengfang

2006-10-20

Lawrence Berkeley National Laboratory (LBNL) is now finalizing the Phase 2 Research and Demonstration Project on characterizing 2-foot x 4-foot (61-cm x 122-cm) fan-filter units in the market using the first-ever standard laboratory test method developed at LBNL.[1][2][3] Fan-filter units deliver re-circulated air and provide particle filtration control for clean environments. Much of the energy in cleanrooms (and minienvironments) is consumed by 2-foot x 4-foot (61-cm x 122-cm) or 4-foot x 4-foot (122-cm x 122-cm) fan-filter units that are typically located in the ceiling (25-100% coverage) of cleanroom controlled environments. Thanks to funding support by the California Energy Commission's Industrialmore » Program of the Public Interest Energy Research (PIER) Program, and significant participation from manufacturers and users of fan-filter units from around the world, LBNL has developed and performed a series of standard laboratory tests and reporting on a variety of 2-foot x 4-foot (61-cm x 122-cm) fan-filter units (FFUs). Standard laboratory testing reports have been completed and reported back to anonymous individual participants in this project. To date, such reports on standard testing of FFU performance have provided rigorous and useful data for suppliers and end users to better understand, and more importantly, to quantitatively characterize performance of FFU products under a variety of operating conditions.[1] In the course of the project, the standard laboratory method previously developed at LBNL has been under continuous evaluation and update.[2][3] Based upon the updated standard, it becomes feasible for users and suppliers to characterize and evaluate energy performance of FFUs in a consistent way.« less

Relying on High-Stakes Standardized Tests to Evaluate Schools and Teachers: A Bad Idea

ERIC Educational Resources Information Center

Morgan, Hani

2016-01-01

In the twenty-first century, the use of standardized tests as the primary means to evaluate schools and teachers in the United States has contributed to severe dilemmas, including misleading information on what students know, lower-level instruction, cheating, less collaboration, unfair treatment of teachers, and biased teaching. This article…

Estimating Achievement Gaps from Test Scores Reported in Ordinal "Proficiency" Categories

ERIC Educational Resources Information Center

Ho, Andrew D.; Reardon, Sean F.

2012-01-01

Test scores are commonly reported in a small number of ordered categories. Examples of such reporting include state accountability testing, Advanced Placement tests, and English proficiency tests. This paper introduces and evaluates methods for estimating achievement gaps on a familiar standard-deviation-unit metric using data from these ordered…

Corrective Action Investigation Plan for Corrective Action Unit 563: Septic Systems, Nevada Test Site, Nevada, with Errata Sheet, Revision 0 (in English; Afrikaans)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alfred Wickline

Corrective Action Unit 563, Septic Systems, is located in Areas 3 and 12 of the Nevada Test Site, which is 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 563 is comprised of the four corrective action sites (CASs) below: • 03-04-02, Area 3 Subdock Septic Tank • 03-59-05, Area 3 Subdock Cesspool • 12-59-01, Drilling/Welding Shop Septic Tanks • 12-60-01, Drilling/Welding Shop Outfalls These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives. Additional information will be obtained by conducting a corrective actionmore » investigation (CAI) before evaluating corrective action alternatives and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document.« less

Atomization of coal water mixtures: evaluation of fuel nozzles and a cellulose gum simulant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosfjord, T.J.

1985-03-01

An experimental evaluation of four air-assist fuel nozzles has been conducted to determine atomization levels of coal-water mixture (CWM) fuels at operating conditions simulating a high pressure combustor. Two of the nozzles were commercial units marketed for use in atmospheric burners, while two nozzles were specially designed for CWM operation in a high pressure combustor. Sprays from all four injectors were characterized in tests performed over a range of liquid and air flowrates. Most of the tests were performed using a cellulose-gum water solution prepared to match the viscosity and drip characteristics of an available CWM. Atomization data acquired frommore » a limited test series using the CWM were found to be properly represented by the gum solution data. High levels of atomization (SMD about 10 micron) were achieved by two of the nozzles - one commercial unit and one special unit - at an assist airflow level corresponding to a nozzle air-fuel ratio between 0.6 - 0.8.« less

Cost analysis in a CMHC: determining the cost of staff time.

PubMed

Haring, A; Eckert, C

1979-06-01

The program evaluation and research unit of a community mental health center developed and field-tested a survey form to measure how employees spend their time. The form is divided into direct patient care activities, which include interviewing and testing, conducting therapy, and prescribing medications, and administrative or support activities, which include filling out charts, attending meetings, and training staff. All staff record daily, for one week, the hours and minutes they spend in each activity. Using that data as a base, the evaluation unit can determine the percentage of time staff spend in each activity and the cost of each activity based on staff members' paychecks.

Test Program for Evaluation of Variable Frequency Power Conditioners

DOT National Transportation Integrated Search

1973-08-01

A test program is outlined for variable frequency power conditioners for 3-phase induction motors in vehicle propulsion applications. The Power Conditioner Unit (PCU) performance characteristics are discussed in some detail. Measurement methods, reco...

Flight selection at United Airlines

NASA Technical Reports Server (NTRS)

Traub, W.

1980-01-01

Airline pilot selection proceedures are discussed including psychogical and personality tests, psychomotor performance requirements, and flight skills evaluation. Necessary attitude and personality traits are described and an outline of computer selection, testing, and training techniques is given.

Joint Test Director. Joint Logistics Over-the-Shore II. Test and Evaluation. Analysis and Evaluation Report. JLOTS II Throughput Test.

DTIC Science & Technology

1985-08-01

Class high - speed containerships and their subsequent conversion to a cargo configuration specifically designed for rapid load-offload of military unit...Rough Terrain Forklift SLWT Side-Loadable Warping Tug ST Short Ton STON Short Ton SUROB Surf Observations T-ACS Auxiliary Crane Ship T- AKR Auxiliary Cargo ...their delivery systems for container, breakbulk, and bulk liquid cargo , and to define the operating performance of the combined systems in a joint test

Tdp studies and tests for C. A. Energia Electrica de Venezuela (enelven) at planta ramon laguna, units RL-17 and RL-10. Volume 3. Unit RL-10 turbine generator condition assessment report and units RL-10 and RL-11 boiler feed pump conditon assessment report. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-03-28

The study, conducted by Babcock and Wilcox, was funded by the U.S. Trade and Development agency on behalf of Enelven. In order to maximize generated power output and minimize operating costs at Planta Ramon Laguna, tests were done to evaluate the condition of equipment at the plant. In order to identify any damage and determine the operating output of each unit, assessments were done of the furnaces, boilers, generators and boiler feed pumps being used in the plant. The report presents the results of these tests. This is the last of three volumes and it is divided into the followingmore » sections: (1) Condition Assessment of Unit RL-10 Turbine-Generator; (2) Condition Assessment of Unit RL-10 and RL-11 Boiler Feed Pumps.« less

Transport suction apparatus and absorption materials evaluation

NASA Technical Reports Server (NTRS)

Krupa, Debra T.; Gosbee, John

1991-01-01

The specific objectives were as follows. The effectiveness and function was evaluated of the hand held, manually powered v-vac for suction during microgravity. The function was evaluated of the battery powered laerdal suction unit in microgravity. The two units in control of various types of simulated bodily fluids were compared. Various types of tubing and attachments were evaluated which are required to control the collection of bodily fluids during transport. Various materials were evaluated for absorption of simulated bodily fluids. And potential problems were identified for waste management and containment of secretions and fluids during transport. Test procedures, results, and conclusions are briefly discussed.

ITEM ANALYSIS OF THREE SPANISH NAMING TESTS: A CROSS-CULTURAL INVESTIGATION

PubMed Central

de la Plata, Carlos Marquez; Arango-Lasprilla, Juan Carlos; Alegret, Montse; Moreno, Alexander; Tárraga, Luis; Lara, Mar; Hewlitt, Margaret; Hynan, Linda; Cullum, C. Munro

2009-01-01

Neuropsychological evaluations conducted in the United States and abroad commonly include the use of tests translated from English to Spanish. The use of translated naming tests for evaluating predominately Spanish-speakers has recently been challenged on the grounds that translating test items may compromise a test’s construct validity. The Texas Spanish Naming Test (TNT) has been developed in Spanish specifically for use with Spanish-speakers; however, it is unlikely patients from diverse Spanish-speaking geographical regions will perform uniformly on a naming test. The present study evaluated and compared the internal consistency and patterns of item-difficulty and -discrimination for the TNT and two commonly used translated naming tests in three countries (i.e., United States, Colombia, Spain). Two hundred fifty two subjects (126 demented, 116 nondemented) across three countries were administered the TNT, Modified Boston Naming Test-Spanish, and the naming subtest from the CERAD. The TNT demonstrated superior internal consistency to its counterparts, a superior item difficulty pattern than the CERAD naming test, and a superior item discrimination pattern than the MBNT-S across countries. Overall, all three Spanish naming tests differentiated nondemented and moderately demented individuals, but the results suggest the items of the TNT are most appropriate to use with Spanish-speakers. Preliminary normative data for the three tests examined in each country are provided. PMID:19208960

Evaluation of conditions necessary for successful bioprocessing of gray water in a microgravity environment

NASA Astrophysics Data System (ADS)

Urban, James E.; Supra, Laura; MacKnight, Allen

2000-01-01

A unique combination of researchers are investigating biological and engineering aspects of a biological wastewater treatment system which could effectively function to treat gray water in a microgravity environment such as that on the International Space Station and human-occupied interplanetary spacecraft. As part of the effort, 23 bacterial strains have been isolated from a bioprocessor operating at unit gravity and various strain combinations have been tested in microgravity for survivability and reduction of total organic carbon in ersatz gray water. All tested strains survive equally well in microgravity and unit gravity and each is capable of reducing TOC in microgravity. While the results reported are encouraging, they also reveal that current testing procedures and equipment are inadequate for fully evaluating bioprocessing in microgravity. .

Comparison of cough reflex testing with videoendoscopy in recently extubated intensive care unit patients.

PubMed

Kallesen, Molly; Psirides, Alex; Huckabee, Maggie-Lee

2016-06-01

Orotracheal intubation is known to impair cough reflex, but the validity of cough reflex testing (CRT) as a screening tool for silent aspiration in this population is unknown. One hundred and six participants in a tertiary-level intensive care unit (ICU) underwent CRT and videoendoscopic evaluation of swallowing (VES) within 24 hours of extubation. Cough reflex threshold was established for each participant using nebulized citric acid. Thirty-nine (37%) participants had an absent cough to CRT. Thirteen (12%) participants aspirated on VES, 9 (69%) without a cough response. Sensitivity of CRT to identify silent aspiration was excellent, but specificity was poor. There was a significant correlation between intubation duration and presence of aspiration on VES (P= .0107). There was no significant correlation between silent aspiration on VES and length of intubation, age, sex, diagnosis at intensive care unit admission, indication for intubation, Acute Physiology and Chronic Health Evaluation III score, morphine equivalent dose, or time of testing postextubation. Intensive care unit patients are at increased risk of aspiration in the 24 hours following extubation, and an impaired cough reflex is common. However, CRT overidentifies risk of silent aspiration in this population. Copyright © 2016 Elsevier Inc. All rights reserved.

Testing of refrigerant mixtures in residential heat pumps. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Judge, J.F.; Radermacher, R.

1995-08-01

To contribute to finding the proper substitute for R-22, a test facility was designed and built to measure the steady state and cyclic performance of two air-to-air heat pumps of 2 & 3 refrigeration-ton (RT) capacity. The performance of heat pumps is evaluated based on ASHRAE Standard 116-1983 {open_quotes}Method of Testing for Seasonal Efficiency of Unitary Air-conditioners and Heat Pumps{close_quotes} (47). This standard includes six steady-state tests; three cooling tests (A, B, and C) and three heating tests (High Temperature (47S), Frost Accumulation (35F), and Low Temperature (17L)). The standard also includes two cyclic tests; a cyclic cooling test (D)more » and a cyclic heating test (47C). The results of these tests are used to evaluate the seasonal performance of a heat pump. In the work presented here, two heat pumps (test units) are used. Test unit 1 is a 2 RT split heat pump system using a reciprocating compressor, a short tube, and a thermostatic expansion valve. Test unit 2 is a 3 RT split heat pump system using a scroll compressor and two thermostatic expansion valves. This study investigates four different possibilities for replacing R-22 with R-32/125/134a (30/10/60 wt.%) (Mixture 1) or R-32/125/134a (23/25/52 wt.%) (Mixture 2). The first and simplest scenario is the retrofit with no hardware modifications. The second possibility investigated is altering the refrigerant path to attain a near-counterflow configuration in the indoor coil for the heating mode. The third and most complex possibility is the soft optimization which consists of maximizing the COPs of R-22 and Mixture 2 in the heating and cooling modes by optimizing refrigerant charge and expansion devices. The fourth option investigated is the suction-line heat exchange (SLHX). In unit 1, the first, second, and third scenarios are investigated and in unit 2, the first, second, and fourth scenarios are investigated.« less

Using permutation tests to enhance causal inference in interrupted time series analysis.

PubMed

Linden, Ariel

2018-06-01

Interrupted time series analysis (ITSA) is an evaluation methodology in which a single treatment unit's outcome is studied serially over time and the intervention is expected to "interrupt" the level and/or trend of that outcome. The internal validity is strengthened considerably when the treated unit is contrasted with a comparable control group. In this paper, we introduce a robustness check based on permutation tests to further improve causal inference. We evaluate the effect of California's Proposition 99 for reducing cigarette sales by iteratively casting each nontreated state into the role of "treated," creating a comparable control group using the ITSAMATCH package in Stata, and then evaluating treatment effects using ITSA regression. If statistically significant "treatment effects" are estimated for pseudotreated states, then any significant changes in the outcome of the actual treatment unit (California) cannot be attributed to the intervention. We perform these analyses setting the cutpoint significance level to P > .40 for identifying balanced matches (the highest threshold possible for which controls could still be found for California) and use the difference in differences of trends as the treatment effect estimator. Only California attained a statistically significant treatment effect, strengthening confidence in the conclusion that Proposition 99 reduced cigarette sales. The proposed permutation testing framework provides an additional robustness check to either support or refute a treatment effect identified in for the true treated unit in ITSA. Given its value and ease of implementation, this framework should be considered as a standard robustness test in all multiple group interrupted time series analyses. © 2018 John Wiley & Sons, Ltd.

Status of Hollow Cathode Heater Development for the Space Station Plasma Contactor

NASA Technical Reports Server (NTRS)

Soulas, George C.

1994-01-01

A hollow cathode-based plasma contactor has been selected for use on the Space Station. During the operation of the plasma contactor, the hollow cathode heater will endure approximately 12000 thermal cycles. Since a hollow cathode heater failure would result in a plasma contactor failure, a hollow cathode heater development program was established to produce a reliable heater. The development program includes the heater design, process documents for both heater fabrication and assembly, and heater testing. The heater design was a modification of a sheathed ion thruster cathode heater. Heater tests included testing of the heater unit alone and plasma contactor and ion thruster testing. To date, eight heaters have been or are being processed through heater unit testing, two through plasma contactor testing and three through ion thruster testing, all using direct current power supplies. Comparisons of data from heater unit performance tests before cyclic testing, plasma contactor tests, and ion thruster tests at the ignition input current level show the average deviation of input power and tube temperature near the cathode tip to be +/-0.9 W and +/- 21 C, respectively. Heater unit testing included cyclic testing to evaluate reliability under thermal cycling. The first heater, although damaged during assembly, completed 5985 ignition cycles before failing. Four additional heaters successfully completed 6300, 6300, 700, and 700 cycles. Heater unit testing is currently ongoing for three heaters which have to date accumulated greater than 7250, greater than 5500, and greater than 5500 cycles, respectively.

Planning for an Evaluation of Teaching Performance. Volume IV. Summaries of Instruments for Use in Evaluating Teacher Performance.

ERIC Educational Resources Information Center

Yuzdepski, I., Comp.; Elliott, L., Comp.

This document presents information, in the form of summary sheets, on 54 teacher evaluation instruments. Each summary contains pertinent information about the instrument regarding publishing company, author, criteria evaluated, subject of observation, category dimension, and coding units. The 19 criteria used in the evaluation tests, which were…

An Update on the Ever Growing Momentum of Teacher Competency Testing.

ERIC Educational Resources Information Center

Flippo, Rona F.

Teacher competency testing for the purpose of screening persons prior to state certification continues to be on the upswing in the United States. Many states have implemented paper-pencil tests, most of which were prepared by Educational Testing Service and National Evaluation Systems. Problem areas to consider when certification tests are used to…

[A new machinability test machine and the machinability of composite resins for core built-up].

PubMed

Iwasaki, N

2001-06-01

A new machinability test machine especially for dental materials was contrived. The purpose of this study was to evaluate the effects of grinding conditions on machinability of core built-up resins using this machine, and to confirm the relationship between machinability and other properties of composite resins. The experimental machinability test machine consisted of a dental air-turbine handpiece, a control weight unit, a driving unit of the stage fixing the test specimen, and so on. The machinability was evaluated as the change in volume after grinding using a diamond point. Five kinds of core built-up resins and human teeth were used in this study. The machinabilities of these composite resins increased with an increasing load during grinding, and decreased with repeated grinding. There was no obvious correlation between the machinability and Vickers' hardness; however, a negative correlation was observed between machinability and scratch width.

Mathematics Library of Test Items. Volume One.

ERIC Educational Resources Information Center

Fraser, Graham, Ed.

As one in a series of test item collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, items of value from previous tests are made available to teachers for the construction of pretests or posttests, reference tests for inter-class comparisons and general assignments. The collection was reviewed for content…

Sled Tests Using the Hybrid III Rail Safety ATD and Workstation Tables for Passenger Trains

DOT National Transportation Integrated Search

2017-08-01

The Hybrid III Rail Safety (H3-RS) anthropomorphic test device (ATD) is a crash test dummy developed in the United Kingdom to evaluate abdomen and lower thorax injuries that occur when passengers impact workstation tables during train accidents. The ...

Field Evaluation of the Performance of the RTU Challenge Unit: Daikin Rebel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katipamula, Srinivas; Wang, W.; Ngo, Hung

2017-05-31

Packaged rooftop air-conditioning units (RTUs) are used in 44% (2.5 million) of all commercial buildings, serving over 57% (46 billion square feet) of the commercial building floor space in the United States (EIA 2012). The primary energy consumption associated with RTUs is over 2.2 quads annually. Therefore, even a small improvement in efficiency or part-load operation of these units can lead to significant reductions in energy use and carbon emissions. Starting in 2011, the U.S. Department of Energy’s (DOE’s) Building Technologies Office funded a series of projects related to RTUs. Some projects were intended to improve the operating efficiency ofmore » the existing RTUs, while others were focused on improving the operating efficiency of new units. This report documents the field-testing and comparison of the seasonal efficiency of a state-of-art RTU Challenge unit and a standard unit. Section II provides the background for the work. Section III describes the measurement and verification plan for the field tests. Section IV describes the measurement and verification evaluation plan. The results are described in Section V. The lessons learned and recommendations for future work are presented in Section VI. A list of references is provided in Section VII.« less

Tensile testing of thin-film microstructures

NASA Astrophysics Data System (ADS)

Greek, Staffan; Johansson, Stefan A. I.

1997-09-01

The mechanical properties of thin film microstructures depend on size and shape and on the film manufacturing process. Hence, the test structures that are used to measure mechanical properties should have dimensions of the same order of magnitude as an application structure. The microstructures are easily monitored in a scanning electron microscope (SEM), but to be handled and tested in situ a micromanipulator was developed. The parts of the micromanipulator essential to the tests are two independently moveable tables driven by electric motors. The test structures and a testing unit are mounted on the tables. A testing unit was designed to measure force and displacement with high resolution. The testing unit consists of an arm actuated by a piezoelectric element and equipped with a probe. An optical encoder measures the movement of the arm, while strain gauges measure the force in the arm. Test structures consist typically of a released beam fixed at one end with a ring at the other. The micromanipulator is used to position the probe of the testing unit in the ring. The testing unit then executed a tensile test of the beam. Test structures of polysilicon films produced under various process conditions were used to verify the possibility of measuring Young's modulus with an accuracy of +/- 5 percent, as well as fracture strength.Young's modulus is calculated using the difference in elongation for different beam lengths. The fracture strength of the beams was evaluated with Weibull statistics.

Tdp studies and tests for C. A. Energia Electrica de Venezuela (enelven) at planta ramon laguna, units RL-17 and RL-10. Volume 2. Unit RL-10 boiler condition assessment report. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-03-28

The study, conducted by Babcock and Wilcox, was funded by the U.S. Trade and Development agency on behalf of Enelven. In order to maximize generated power output and minimize operating costs at Planta Ramon Laguna, tests were done to evaluate the condition of equipment at the plant. In order to identify any damage and determine the operating output of each unit, assessments were done of the furnaces, boilers, generators and boiler feed pumps being used in the plant. The report presents the results of these tests. This is the second of three volumes and it includes the following section: (1)more » Condition Assessment of Unit RL-10 Boiler.« less

Flight test of an improved solid waste collection system

NASA Technical Reports Server (NTRS)

Thornton, W.; Brasseaux, H.; Whitmore, H.

1991-01-01

A system for human waste collection is described and evaluated on the basis of a prototype employed for the shuttle flight STS-35. The manually operated version of the unit is designed to collect, compact, and store human waste and cleaning material in replaceable volumes. The system is presented with illustrations and descriptions of the disposable pads that are used to clean the cylinder and occlusive air valves as well as seal the unit. Temporary retention and waste entrainment are provided by the variable airflow in the manual unit tested. The prototype testing indicates that sufficient airflow is achieved at 45 CFM and that the stowage volume (18.7 cu in.) is adequate for storing human waste with minimal logistical support. Higher compaction pressure and the use of a directed airstream are proposed for improving the packing efficiency of the unit.

Validation of Welding Curriculum Manual.

ERIC Educational Resources Information Center

Stone, Sheila D.

A study was conducted to validate the welding curriculum materials developed and published by the Oklahoma State Department of Vocational and Technical Education. Twelve instructors collected achievement data (unit tests, assignment sheets, and evaluation forms) concerning the performance of 280 students on a total of 46 instructional units. Item…

Initial closed operation of the CELSS Test Facility Engineering Development Unit

NASA Technical Reports Server (NTRS)

Kliss, M.; Blackwell, C.; Zografos, A.; Drews, M.; MacElroy, R.; McKenna, R.; Heyenga, A. G.

2003-01-01

As part of the NASA Advanced Life Support Flight Program, a Controlled Ecological Life Support System (CELSS) Test Facility Engineering Development Unit has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The Engineering Development Unit (EDU) is a tightly closed, stringently controlled, ground-based testbed which provides a broad range of environmental conditions under which a variety of CELSS higher plant crops can be grown. Although the EDU was developed primarily to provide near-term engineering data and a realistic determination of the subsystem and system requirements necessary for the fabrication of a comparable flight unit, the EDU has also provided a means to evaluate plant crop productivity and physiology under controlled conditions. This paper describes the initial closed operational testing of the EDU, with emphasis on the hardware performance capabilities. Measured performance data during a 28-day closed operation period are compared with the specified functional requirements, and an example of inferring crop growth parameters from the test data is presented. Plans for future science and technology testing are also discussed. Published by Elsevier Science Ltd on behalf of COSPAR.

Charge-Control Unit for Testing Lithium-Ion Cells

NASA Technical Reports Server (NTRS)

Reid, Concha M.; Mazo, Michelle A.; Button, Robert M.

2008-01-01

A charge-control unit was developed as part of a program to validate Li-ion cells packaged together in batteries for aerospace use. The lithium-ion cell charge-control unit will be useful to anyone who performs testing of battery cells for aerospace and non-aerospace uses and to anyone who manufacturers battery test equipment. This technology reduces the quantity of costly power supplies and independent channels that are needed for test programs in which multiple cells are tested. Battery test equipment manufacturers can integrate the technology into their battery test equipment as a method to manage charging of multiple cells in series. The unit manages a complex scheme that is required for charging Li-ion cells electrically connected in series. The unit makes it possible to evaluate cells together as a pack using a single primary test channel, while also making it possible to charge each cell individually. Hence, inherent cell-to-cell variations in a series string of cells can be addressed, and yet the cost of testing is reduced substantially below the cost of testing each cell as a separate entity. The unit consists of electronic circuits and thermal-management devices housed in a common package. It also includes isolated annunciators to signal when the cells are being actively bypassed. These annunciators can be used by external charge managers or can be connected in series to signal that all cells have reached maximum charge. The charge-control circuitry for each cell amounts to regulator circuitry and is powered by that cell, eliminating the need for an external power source or controller. A 110-VAC source of electricity is required to power the thermal-management portion of the unit. A small direct-current source can be used to supply power for an annunciator signal, if desired.

Which Fecal Immunochemical Test Should I Choose?

PubMed Central

Daly, Jeanette M.; Xu, Yinghui; Levy, Barcey T.

2017-01-01

Objectives: To summarize the fecal immunochemical tests (FITs) available in the United States, the 2014 pathology proficiency testing (PT) program FIT results, and the literature related to the test characteristics of FITs available in the United States to detect advanced adenomatous polyps (AAP) and/or colorectal cancer (CRC). Methods: Detailed review of the Food and Drug Administration’s Clinical Laboratory Improvement Amendments (CLIA) database of fecal occult blood tests, the 2014 FIT PT program results, and the literature related to FIT accuracy. Results: A search of the CLIA database identified 65 FITs, with 26 FITs available for purchase in the United States. Thirteen of these FITs were evaluated on a regular basis by PT programs, with an overall sensitivity of 99.1% and specificity of 99.2% for samples spiked with hemoglobin. Automated FITs had better sensitivity and specificity than CLIA-waived FITs for detection of AAP and CRC in human studies using colonoscopy as the gold standard. Conclusion: Although many FITs are available in the United States, few have been tested in proficiency testing programs. Even fewer have data in humans on sensitivity and specificity for AAP or CRC. Our review indicates that automated FITs have the best test characteristics for AAP and CRC. PMID:28447866

HIV testing for acute medical admissions: evaluation of a pilot study in Leicester, England.

PubMed

Palfreeman, Adrian; Nyatsanza, Farai; Farn, Helen; McKinnon, Graham; Schober, Paul; McNally, Paul

2013-06-01

The 2008 UK National Guidelines for HIV testing recommended HIV testing should be offered to all general medical admissions aged 16-60 years in high prevalence areas, and that this should be evaluated to ensure this was effective in diagnosing previously undiagnosed HIV. HIV testing was introduced as a routine test for all patients admitted to the acute medical admissions unit, comparisons were made between the testing rates before, during and after this intervention. The pilot was initiated in August 2009. Prior to the pilot the unit was carrying out 15 tests per month. However, when the pilot was introduced 82 tests were being carried out per month with a total of 10 new diagnoses since the start of the pilot. The proportion of patients tested versus those eligible for testing remained low varying between 6% and 22% month by month. 10 patients we found to be HIV positive with a prevalence of approximately 1%, 10 fold higher than the cut off for cost effectiveness used in the guidelines. Overall the pilot showed that HIV testing could be delivered without the use of extra resources and is acceptable to patients.

Teacher Evaluation and Music Education: Joining the National Discussion

ERIC Educational Resources Information Center

Overland, Corin T.

2014-01-01

Between 2009 and 2014, thirty-seven states in the United States have adopted or significantly amended their teacher evaluation laws, mostly shifting toward using measurements of student growth on achievement tests. Yet, the processes to evaluate core subjects have not always transitioned smoothly to nontested or artistic content, causing some…

Minnesota urban partnership agreement national evaluation : content analysis test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the content analysis test plan for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing congestion by employing ...

Minnesota urban partnership agreement national evaluation : telecommuting test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the telecommuting test plan for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing congestion by employing str...

Initial Field Deployment Results of Green PCB Removal from Sediment Systems (GPRSS)

NASA Technical Reports Server (NTRS)

Devor, Robert; Captain, James; Weis, Kyle; Maloney, Phillip; Booth, Greg; Quinn, Jacqueline

2014-01-01

Purpose of Study: (a) Develop/optimize technology capable of removing PCBs from contaminated sediments; (b) Develop design for functional GPRSS unit; (c) Produce and prove functionality of prototype units in a laboratory settings; (d) Produce fully-functional GPRSS units for testing at a demonstration site in Altavista, VA; and (e) Evaluate efficacy of GPRSS technology for the remediation of PCB-contaminated sediments.

Fiscal Year 2012 United States Air Force Agency Financial Report

DTIC Science & Technology

2012-01-01

Air Force Research Laboratory (AFRL) and Lawrence Livermore National Laboratory (LLNL) aggressively designed and tested an advanced warhead to...Reaper procurement & RPA capabilities, Light Attack Armed Reconnaissance buys, Joint Strike Fighter, satellites). Research , Development, Test and...Military Personnel Operations, Readiness & Support Procurement Research , Development, Test & Evaluation

Application of in vitro extraction studies to evaluate element bioaccessibility in soils from a transect across the United States and Canada

USGS Publications Warehouse

Morman, S.A.; Plumlee, G.S.; Smith, D.B.

2009-01-01

In vitro bioaccessibility tests (IVBA) are inexpensive, physiologically-based extraction tests designed to estimate the bioaccessibility of elements along ingestion exposure pathways. Published IVBA protocols call for the testing to be done on the Pb > Ni > As > Cr.

Evaluation Plan for the Computerized Adaptive Vocational Aptitude Battery.

ERIC Educational Resources Information Center

Green, Bert F.; And Others

The United States Armed Services are planning to introduce computerized adaptive testing (CAT) into the Armed Services Vocational Aptitude Battery (ASVAB), which is a major part of the present personnel assessment procedures. Adaptive testing will improve efficiency greatly by assessing each candidate's answers as the test progresses and posing…

Personnel Development for Entrepreneurs.

ERIC Educational Resources Information Center

Sanders, Leon; And Others

Divided into three units, this curriculum guide on entrepreneur education covers nineteen individual areas of instruction and can be conducted in a series of nine workshops. (The development, field testing, and evaluation of the curriculum are reported separately as CE 015 581.) Unit I covers the following areas of instruction: planning,…

Towards a national certification scheme for Rubus in the United States

USDA-ARS?s Scientific Manuscript database

Guidelines for a National Certification Scheme for Rubus in the United States have been drafted and are being evaluated in states with a tradition of Rubus propagation. The major components of the guidelines describe the procedures for propagating, testing and maintaining plants at four successive s...

A Formative Evaluation of Me Now, Unit I, Digestion and Circulation, Life Sciences for the Educable Mentally Handicapped Intermediate Grades (11-13 years).

ERIC Educational Resources Information Center

Robinson, James T.; Tolman, Richard R.

In order to evaluate Unit I (Digestion and Circulation) of the Me Now series of Life Sciences for the Educable Mentally Handicapped, 139 students in an experimental group (mean IQ 72.04; mean CA 144.9 months) and 154 control subjects (mean IQ 70.2; mean CA 148.3 months) were pre- and post-tested following instruction in the Me Now series…

Evaluation of effect of different disposable infection control barriers on light intensity of light-curing unit and microhardness of composite - An in vitro study

PubMed Central

Khode, Rajiv Tarachand; Shenoi, Pratima Ramakrishna; Kubde, Rajesh R.; Makade, Chetana S.; Wadekar, Kanchan D.; Khode, Priyanka Tarachand

2017-01-01

Aims: This study evaluated effect of infection control barriers on light intensity (LI) of light-curing unit (LCU) and microhardness of composite. Materials and Methods: Four different disposable barriers (n = 30) were tested against the control. LI for each barrier was measured with Lux meter. One hundred and fifty Teflon molds were equally divided into five groups of thirty each. Composite was filled in bulk in these molds and cured without and with barrier. Microhardness was evaluated on top and bottom surface of composite specimen with microhardness testing machine and hardness ratio (HR) was derived. Statistical Analysis Used: One-way analysis of variance, Tukey's honestly significant difference test, and paired t-test using SPSS version 18 software. Results: All barriers had significantly reduced the baseline LI of LCU (P < 0.0001), but only Cure Elastic Steri-Shield and latex cut glove pieces (LCGP) significantly reduced the microhardness of the composite (P < 0.05). However, HR determined inadequate curing only with LCGP. Conclusions: Although entire tested barrier significantly reduced the LI; none, except LCGP markedly affected the degree of cure of the composite. PMID:29279622

Corrective Action Investigation Plan for Corrective Action Unit 374: Area 20 Schooner Unit Crater Nevada Test Site, Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patrick Matthews

Corrective Action Unit 374 is located in Areas 18 and 20 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 374 comprises the five corrective action sites (CASs) listed below: • 18-22-05, Drum • 18-22-06, Drums (20) • 18-22-08, Drum • 18-23-01, Danny Boy Contamination Area • 20-45-03, U-20u Crater (Schooner) These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAsmore » and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on October 20, 2009, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 374.« less

Corrective Action Investigation Plan for Corrective Action Unit 536: Area 3 Release Site, Nevada Test Site, Nevada (Rev. 0 / June 2003), Including Record of Technical Change No. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office's approach to collect the data necessary to evaluate corrective action alternatives (CAAs) appropriate for the closure of Corrective Action Unit (CAU) 536: Area 3 Release Site, Nevada Test Site, Nevada, under the Federal Facility Agreement and Consent Order. Corrective Action Unit 536 consists of a single Corrective Action Site (CAS): 03-44-02, Steam Jenny Discharge. The CAU 536 site is being investigated because existing information on the nature and extent of possible contamination is insufficient to evaluate and recommend corrective action alternatives formore » CAS 03-44-02. The additional information will be obtained by conducting a corrective action investigation (CAI) prior to evaluating CAAs and selecting the appropriate corrective action for this CAS. The results of this field investigation are to be used to support a defensible evaluation of corrective action alternatives in the corrective action decision document. Record of Technical Change No. 1 is dated 3-2004.« less

Testing the suitability of geologic frameworks for extrapolating hydraulic properties across regional scales

DOE PAGES

Mirus, Benjamin B.; Halford, Keith J.; Sweetkind, Donald; ...

2016-02-18

The suitability of geologic frameworks for extrapolating hydraulic conductivity (K) to length scales commensurate with hydraulic data is difficult to assess. A novel method is presented for evaluating assumed relations between K and geologic interpretations for regional-scale groundwater modeling. The approach relies on simultaneous interpretation of multiple aquifer tests using alternative geologic frameworks of variable complexity, where each framework is incorporated as prior information that assumes homogeneous K within each model unit. This approach is tested at Pahute Mesa within the Nevada National Security Site (USA), where observed drawdowns from eight aquifer tests in complex, highly faulted volcanic rocks providemore » the necessary hydraulic constraints. The investigated volume encompasses 40 mi3 (167 km3) where drawdowns traversed major fault structures and were detected more than 2 mi (3.2 km) from pumping wells. Complexity of the five frameworks assessed ranges from an undifferentiated mass of rock with a single unit to 14 distinct geologic units. Results show that only four geologic units can be justified as hydraulically unique for this location. The approach qualitatively evaluates the consistency of hydraulic property estimates within extents of investigation and effects of geologic frameworks on extrapolation. Distributions of transmissivity are similar within the investigated extents irrespective of the geologic framework. In contrast, the extrapolation of hydraulic properties beyond the volume investigated with interfering aquifer tests is strongly affected by the complexity of a given framework. As a result, testing at Pahute Mesa illustrates how this method can be employed to determine the appropriate level of geologic complexity for large-scale groundwater modeling.« less

Testing the suitability of geologic frameworks for extrapolating hydraulic properties across regional scales

USGS Publications Warehouse

Mirus, Benjamin B.; Halford, Keith J.; Sweetkind, Donald; Fenelon, Joseph M.

2016-01-01

The suitability of geologic frameworks for extrapolating hydraulic conductivity (K) to length scales commensurate with hydraulic data is difficult to assess. A novel method is presented for evaluating assumed relations between K and geologic interpretations for regional-scale groundwater modeling. The approach relies on simultaneous interpretation of multiple aquifer tests using alternative geologic frameworks of variable complexity, where each framework is incorporated as prior information that assumes homogeneous K within each model unit. This approach is tested at Pahute Mesa within the Nevada National Security Site (USA), where observed drawdowns from eight aquifer tests in complex, highly faulted volcanic rocks provide the necessary hydraulic constraints. The investigated volume encompasses 40 mi3 (167 km3) where drawdowns traversed major fault structures and were detected more than 2 mi (3.2 km) from pumping wells. Complexity of the five frameworks assessed ranges from an undifferentiated mass of rock with a single unit to 14 distinct geologic units. Results show that only four geologic units can be justified as hydraulically unique for this location. The approach qualitatively evaluates the consistency of hydraulic property estimates within extents of investigation and effects of geologic frameworks on extrapolation. Distributions of transmissivity are similar within the investigated extents irrespective of the geologic framework. In contrast, the extrapolation of hydraulic properties beyond the volume investigated with interfering aquifer tests is strongly affected by the complexity of a given framework. Testing at Pahute Mesa illustrates how this method can be employed to determine the appropriate level of geologic complexity for large-scale groundwater modeling.

Testing the suitability of geologic frameworks for extrapolating hydraulic properties across regional scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mirus, Benjamin B.; Halford, Keith J.; Sweetkind, Donald

The suitability of geologic frameworks for extrapolating hydraulic conductivity (K) to length scales commensurate with hydraulic data is difficult to assess. A novel method is presented for evaluating assumed relations between K and geologic interpretations for regional-scale groundwater modeling. The approach relies on simultaneous interpretation of multiple aquifer tests using alternative geologic frameworks of variable complexity, where each framework is incorporated as prior information that assumes homogeneous K within each model unit. This approach is tested at Pahute Mesa within the Nevada National Security Site (USA), where observed drawdowns from eight aquifer tests in complex, highly faulted volcanic rocks providemore » the necessary hydraulic constraints. The investigated volume encompasses 40 mi3 (167 km3) where drawdowns traversed major fault structures and were detected more than 2 mi (3.2 km) from pumping wells. Complexity of the five frameworks assessed ranges from an undifferentiated mass of rock with a single unit to 14 distinct geologic units. Results show that only four geologic units can be justified as hydraulically unique for this location. The approach qualitatively evaluates the consistency of hydraulic property estimates within extents of investigation and effects of geologic frameworks on extrapolation. Distributions of transmissivity are similar within the investigated extents irrespective of the geologic framework. In contrast, the extrapolation of hydraulic properties beyond the volume investigated with interfering aquifer tests is strongly affected by the complexity of a given framework. As a result, testing at Pahute Mesa illustrates how this method can be employed to determine the appropriate level of geologic complexity for large-scale groundwater modeling.« less

Tier One Performance Screen Initial Operational Test and Evaluation: 2011 Annual Report

DTIC Science & Technology

2013-01-01

OPERATIONAL TEST AND EVALUATION: 2011 ANNUAL REPORT EXECUTIVE SUMMARY Research Requirement: In addition to educational, physical , and...34 Table 5.4. Incremental Validity Estimates for the TAPAS and TOPS Composite Scales over the AFQT for Predicting IMT Physical Fitness Criteria by...Validity Estimates for the TAPAS and TOPS Composite Scales over the AFQT for Predicting In-Unit Physical Fitness Criteria by Education Tier

United States Air Force Agency Financial Report 2014

DTIC Science & Technology

2014-01-01

basic sciences and 45 semester hours in humanities and social sciences . This 90 semester hour total comprises 60 percent of the total academic...Test and Evaluation Support $723 F-35 $628 Defense Research Sciences $373 GPS III-Operational Control Segment $373 Long Range Strike Bomber $359...Development, Test & Evaluation Family Housing & Military Construction (Less: Earned Revenue) Net Cost before Losses/ (Gains) from Actuarial Assumption

Thermal energy storage evaluation and life testing

NASA Astrophysics Data System (ADS)

Richter, R.

1983-01-01

Two thermal energy storage (TES) units which were built under a previous contract were tested with a Hi-Cap Vuilleumier cryogenic cooler in the facility of the Hughes Aircraft Corporation. The objective of the program was the evaluation of the behavior of the TES units as well as the determination of the temperature history of the three cold stages of the Vuilleumier cryogenic cooler during cyclic charging and discharging of the TES units. The test results have confirmed that thermal energy storage can provide the necessary thermal power to the hot cylinders of the Vuilleumier cryogenic cooler at the required operating temperatures. Thereby the continuous cooling capability of the cooler during an eclipse when no electrical power is available is being assured. The cold stage temperature amplitudes during a complete charge discharge cycle of the TES units were only about 10% of the amplitudes which were observed when the Hi-Cap Vuilleumier cryogenic cooler was operating without thermal energy storage backup in a simulated orbit of 54 minutes sun exposure and 18 minutes eclipse time. The themal conductivity of the molten thermal energy storage salt was apparently only a fraction of the thermal conductivity which had been assumed for the prediction of the upper heater temperatures. A redesign of the heater temperatures below 1480 degrees F which is now required for full charging of the TES units within 54 minutes with the present heater design.

Achievement Test Preparation: A Year-Long Goal, Not a Last-Minute Thought.

ERIC Educational Resources Information Center

Matter, M. Kevin; Ligon, Glynn

Yearly administrations of a standardized achievement test are a part of the educational process in many school districts in the United States. The Systemwide Testing Program in the Austin Independent School District Office of Research and Evaluation has gradually developed a process and support materials whereby the test administrations are a tool…

Sporicidal activity of a new low-temperature sterilization technology: the Sterrad 50 sterilizer.

PubMed

Rutala, W A; Gergen, M F; Weber, D J

1999-07-01

This study was undertaken to evaluate the efficacy of a new low-temperature sterilization system that recently has been cleared by the Food and Drug Administration, the Sterrad 50. Flat stainless steel carriers were inoculated with approximately 10(6) Bacillus stearothermophilus spores. These carriers were placed aseptically in the middle of 40-cm-long stainless steel-lumened test units of varying diameters (1 mm, 2 mm, and 3 mm). After inoculation, the test units were processed in the Sterrad 50. After sterilization, the carriers were assayed for growth of the B. stearothermophilus spores. Our data demonstrated that the Sterrad 50 was highly effective in killing the B. stearothermophilus spores (no positive carriers with 30 tests of each lumen-diameter test unit). The Sterrad 50 is likely to be clinically useful for the sterilization of heat-sensitive medical equipment.

Minnesota urban partnership agreement national evaluation : cost benefit analysis test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the cost benefit analysis test plan for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing congestion by emplo...

Minnesota urban partnership agreement national evaluation : safety data test plan.

DOT National Transportation Integrated Search

2009-11-17

This report provides the safety data test plan for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing congestion by employing strat...

Minnesota urban partnership agreement national evaluation : traffic system data test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the traffic system data test plan for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing congestion by employi...

San Francisco urban partnership agreement, national evaluation : exogenous factors test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing exogenous factors data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA projects...

Minnesota urban partnership agreement national evaluation : tolling test plan.

DOT National Transportation Integrated Search

2009-11-17

This report presents the test plan for collecting and analyzing toll data for the Minnesota Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The Minnesota UPA projects focus on reducing co...

San Francisco urban partnership agreement, national evaluation : environmental data test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing environmental data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA projects foc...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2013 CFR

2013-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2014 CFR

2014-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

40 CFR 63.1571 - How and when do I conduct a performance test or other initial compliance demonstration?

Code of Federal Regulations, 2012 CFR

2012-07-01

... performance evaluation or test for a semi-regenerative catalytic reforming unit catalyst regenerator vent, you... properties. Examples of analytical methods include, but are not limited to: (i) Use of material balances...

Hollow cathode heater development for the Space Station plasma contactor

NASA Technical Reports Server (NTRS)

Soulas, George C.

1993-01-01

A hollow cathode-based plasma contactor has been selected for use on the Space Station. During the operation of the plasma contactor, the hollow cathode heater will endure approximately 12000 thermal cycles. Since a hollow cathode heater failure would result in a plasma contactor failure, a hollow cathode heater development program was established to produce a reliable heater design. The development program includes the heater design, process documents for both heater fabrication and assembly, and heater testing. The heater design was a modification of a sheathed ion thruster cathode heater. Three heaters have been tested to date using direct current power supplies. Performance testing was conducted to determine input current and power requirements for achieving activation and ignition temperatures, single unit operational repeatability, and unit-to-unit operational repeatability. Comparisons of performance testing data at the ignition input current level for the three heaters show the unit-to-unit repeatability of input power and tube temperature near the cathode tip to be within 3.5 W and 44 degrees C, respectively. Cyclic testing was then conducted to evaluate reliability under thermal cycling. The first heater, although damaged during assembly, completed 5985 ignition cycles before failing. Two additional heaters were subsequently fabricated and have completed 3178 cycles to date in an on-going test.

SIMS prototype system 1 test results: Engineering analysis

NASA Technical Reports Server (NTRS)

1978-01-01

The space and domestic water solar heating system designated SIMS Prototype Systems 1 was evaluated. The test system used 720 ft (gross) of Solar Energy Products Air Collectors, a Solar Control Corporation SAM 20 Air Handler with Model 75-175 control unit, a Jackson Solar Storage tank with Rho Sigma Mod 106 controller, and 20 tons of rack storage. The test data analysis performed evaluates the system performance and documents the suitability of SIMS Prototype System 1 hardware for field installation.

Engaging Frontline Staff in Performance Improvement: The American Organization of Nurse Executives Implementation of Transforming Care at the Bedside Collaborative.

PubMed

Needleman, Jack; Pearson, Marjorie L; Upenieks, Valda V; Yee, Tracy; Wolstein, Joelle; Parkerton, Melissa

2016-02-01

Process improvement stresses the importance of engaging frontline staff in implementing new processes and methods. Yet questions remain on how to incorporate these activities into the workday of hospital staff or how to create and maintain its commitment. In a 15-month American Organization of Nurse Executives collaborative involving frontline medical/surgical staff from 67 hospitals, Transforming Care at the Bedside (TCAB) was evaluated to assess whether participating units successfully implemented recommended change processes, engaged staff, implemented innovations, and generated support from hospital leadership and staff. In a mixed-methods analysis, multiple data sources, including leader surveys, unit staff surveys, administrative data, time study data, and collaborative documents were used. All units reported establishing unit-based teams, of which >90% succeeded in conducting tests of change, with unit staff selecting topics and making decisions on adoption. Fifty-five percent of unit staff reported participating in unit meetings, and 64%, in tests of change. Unit managers reported substantial increase in staff support for the initiative. An average 36 tests of change were conducted per unit, with 46% of tested innovations sustained, and 20% spread to other units. Some 95% of managers and 97% of chief nursing officers believed that the program had made unit staff more likely to initiate change. Among staff, 83% would encourage adoption of the initiative. Given the strong positive assessment of TCAB, evidence of substantial engagement of staff in the work, and the high volume of innovations tested, implemented, and sustained, TCAB appears to be a productive model for organizing and implementing a program of frontline-led improvement.

Firefighting module development

NASA Technical Reports Server (NTRS)

Burns, R. A.

1981-01-01

The firefighting module is a lightweight, compact, self contained, helicopter-transportable unit for fighting harbor and other specialty fires as well as for use in emergency water pumping applications. Units were fabricated and tested. A production type unit is undergoing an inservice evaluation and demonstration program at the port of St Louis. The primary purpose is to promote enhanced harbor fire protection at inland and coastal ports. The module and its development are described.

Comparative evaluation of the sporicidal activity of new low-temperature sterilization technologies: ethylene oxide, 2 plasma sterilization systems, and liquid peracetic acid.

PubMed

Rutala, W A; Gergen, M F; Weber, D J

1998-08-01

This study was undertaken to evaluate the efficacy of 4 new low-temperature sterilization technologies: ethylene oxide with hydrochlorofluorocarbons, a liquid peracetic acid immersion system (Steris System 1 Processor), and 2 plasma sterilization processes that use vaporized hydrogen peroxide (Sterrad 100 and the Sterrad 100S). The Sterrad 100S system potentially improves sterilizer efficacy by using 2 cycles of a diffusion stage and a plasma stage per sterilization cycle. Flat stainless steel carriers were inoculated with approximately 10(6) Bacillus stearothermophilus spores. These carriers were aseptically placed in the middle of 40 cm long stainless steel lumens (hollow tubes). Two types of lumen were used:(1) a lumen test unit with a removable 5 cm center piece (1.2 cm diameter) of stainless steel sealed to the narrower steel tubing by hard rubber septums and (2) a straight lumen. Three different diameters of the lumen test unit (1, 2, and 3 mm) and a single diameter of the straight lumen (3 mm) were studied. At least 40 replicates were performed for each type of lumen and sterilization method. After inoculation, the test unit was evaluated in 1 of the low-temperature sterilization technologies. After sterilization, the carriers were cultured in trypticase soy broth for 14 days at 55 degrees C and assessed for growth of B stearothermophilus spores. Our results demonstrated that ethylene oxide with hydrochlorofluorocarbons, the Sterrad 100s, and the Sterrad 100S half cycle were highly effective in killing approximately 10(6) B stearothermophilus spores present in the center of narrow-lumen stainless steel tubes. As the lumen diameter decreased with the lumen test unit, the Sterrad 100 demonstrated reduced ability to kill B stearothermophilus spores present on the carrier. At the smallest diameter tested (1 mm), the Sterrad 100 system failed 74% of the time. The Steris System 1 was not effective in completely eliminating the 10(6) inoculum under test conditions. The Sterrad 100S was significantly superior to the Sterrad 100 system and equivalent to ethylene oxide with hydrochlorofluorocarbons. Introduction of this new Sterrad 100S system should improve the margin of safety and reduce processing costs by its use of a shorter cycle time. The Steris System 1 is limited by diffusion of the chemical sterilant into the interior of the lumen test unit.

9 CFR 104.4 - Products for research and evaluation.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the producer for a small quantity of such product for in vitro Research and Evaluation tests: Provided... Administrator may require in order to assess the product's impact on the environment. (b)(1) A permit to import... and evaluation anywhere in or from the United States unless authorized by the Administrator in...

9 CFR 104.4 - Products for research and evaluation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the producer for a small quantity of such product for in vitro Research and Evaluation tests: Provided... Administrator may require in order to assess the product's impact on the environment. (b)(1) A permit to import... and evaluation anywhere in or from the United States unless authorized by the Administrator in...

Evaluating Metal Probe Meters for Soil Testing.

ERIC Educational Resources Information Center

Hershey, David R.

1992-01-01

Inexpensive metal probe meters that are sold by garden stores can be evaluated by students for their accuracy in measuring soil pH, moisture, fertility, and salinity. The author concludes that the meters are inaccurate and cannot be calibrated in standard units. However, the student evaluations are useful in learning the methods of soil analysis…

EVALUATING PROGRAMMED TEST INTERPRETATION USING EMOTIONAL AROUSAL AS A CRITERION.

ERIC Educational Resources Information Center

FORSTER, JERALD R.

THE QUESTION AS TO WHETHER OR NOT THE EMOTIONAL ASPECTS OF TEST INTERPRETATION MAKE IT INAPPROPRIATE FOR PROGRAMED METHODS WAS EXAMINED BY TWO METHODS OF TEST RESULT COMMUNICATION--PROGRAMED MATERIALS AND VERBAL COMMUNICATION BY A COUNSELOR. DEPENDENT VARIABLES WERE MEASURES OF EMOTIONAL AROUSAL RECORDED BY SKIN CONDUCTANCE UNITS AND THE GAIN IN…

Science Library of Test Items. Volume Four: Practical Testing Guide.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

As one in a series of test items collections developed by the Assessment and Evaluation Unit of the Directorate of Studies, the guide gives a wide range of questions and activities for the manipulation of scientific equipment to allow assessment of students' practical laboratory skills. Instructions are given to make norm-referenced or…

International Space Station United States Oxygen Generator Development Testing

NASA Technical Reports Server (NTRS)

Erickson, Robert J.; Mason, Richard K.

2000-01-01

A life test of a liquid anode feed oxygen generator assembly (OGA) using SPE(R) (United Technologies Corporation, Hamilton Sundstrand Division) membrane technology was terminated in June of 1999. In the total 15,658 hours of operation at MSFC since delivery in 1995, the OGA has produced 2,103 kilograms (kg) (4,632 pounds mass (lbm)) of oxygen, and 263 kg (579 lbm) of hydrogen. Evaluation of cell stack characteristics and oxygen and hydrogen hydrophilic/hydrophobic membrane separators will be discussed.

EVALUATION OF VOLUMETRIC LEAK DETECTION METHODS USED IN UNDERGROUND STORAGE TANKS

EPA Science Inventory

In the spring and summer of 1987, the United States Environmental Protection Agency (EPA) evaluated the performance of 25 commercially available volumetric test methods for the detection of small leaks in underground storage tanks containing gasoline. Performance was estimated by...

Integrated Vehicle-Based Safety Systems (IVBSS) Light Vehicle Field Operational Test Independent Evaluation

DOT National Transportation Integrated Search

2011-10-01

This report presents the methodology and results of the independent evaluation of a prototype integrated crash warning system for : light vehicles as part of the Integrated Vehicle-Based Safety Systems initiative of the United States Department of : ...

San Francisco urban partnership agreement, national evaluation : cost benefit analysis test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing cost and benefit data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA projects ...

San Francisco urban partnership agreement, national evaluation : traveler information data test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing traveler information data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA proje...

San Francisco urban partnership agreement, national evaluation : traffic system data test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing traffic system data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA projects fo...

San Francisco urban partnership agreement, national evaluation : transit system data test plan.

DOT National Transportation Integrated Search

2011-06-01

This report presents the test plan for collecting and analyzing the transit system data for the San Francisco Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Program. The San Francisco UPA project...

Electrical Arc Ignition Testing for Constellation Program

NASA Technical Reports Server (NTRS)

Sparks, Kyle; Gallus, Timothy; Smith, Sarah

2009-01-01

NASA Johnson Space Center (JSC) Materials and Processes Branch requested that NASA JSC White Sands Test Facility (WSTF) perform testing for the Constellation Program to evaluate the hazard of electrical arc ignition of materials that could be in close proximity to batteries. Specifically, WSTF was requested to perform wire-break electrical arc tests to determine the current threshold for ignition of generic cotton woven fabric samples with a fixed voltage of 3.7 V, a common voltage for hand-held electrical devices. The wire-break test was developed during a previous test program to evaluate the hazard of electrical arc ignition inside the Extravehicular Mobility Unit [1].

Analysis of Loss of Ignition of Root Zone of Bioretention Units at the Edison Environmental Center

EPA Science Inventory

Six bioretention units (widths 7.1 m) at USEPA’s Edison Environmental Center were constructed to evaluate sizing of surface area to watershed area. Three sizes were tested in duplicate with changes in aspect ratio of length from inlet (northern) wall by doubling successive ...

30 CFR 33.35 - Methods of drilling; dust-collector unit.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Methods of drilling; dust-collector unit. 33.35 Section 33.35 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL...

30 CFR 33.35 - Methods of drilling; dust-collector unit.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Methods of drilling; dust-collector unit. 33.35 Section 33.35 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL...

30 CFR 33.35 - Methods of drilling; dust-collector unit.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Methods of drilling; dust-collector unit. 33.35 Section 33.35 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL...

30 CFR 33.35 - Methods of drilling; dust-collector unit.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Methods of drilling; dust-collector unit. 33.35 Section 33.35 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL...

30 CFR 33.35 - Methods of drilling; dust-collector unit.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Methods of drilling; dust-collector unit. 33.35 Section 33.35 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL...

The Intelligibility of Indian English. Monograph No. 4.

ERIC Educational Resources Information Center

Bansal, R. K.

Twenty-four English speakers from various regions of India were tested for the intelligibility of their speech. Recordings of speech in a variety of contexts were evaluated by listeners from the United Kingdom, the United States, Nigeria, and Germany. On the basis of the resulting intelligibility scores, factors which tend to hinder…

Quality Evaluation of Coatings by Automatic Scratch Testing

DTIC Science & Technology

1989-11-01

MTL TR 89-98 IADII QUALITY EVALUATION OF COATINGS BY AUTOMATIC SCRATCH TESTING KIRIT J. BHANSALI LBRTR A1 U.S. ARMY MATERIALS TECHNOLOGY LABORATORY...distribution unlimited. LABORATORY COMMANO U.S. ARMY MATERIALS TECHNOLOGY LABORATORY PMUNKS wcamaauv LUaAMUv Watertown, Massachusetts 02172-0001 .o...Theo 7- Kattamis* 9 PEWNWING ORGANIZATION NAME AMO ADDRESS 1.PORUEEET RJC.TS AREA & WORK UNIT NUMSS U.S. Army Materials Technology Laboratory Watertown

United States Air Force Statistical Digest, Fiscal Year 1959. Fourteenth Edition

DTIC Science & Technology

1959-09-30

Support Forces for fiscal year 1959 consist of Air Refueling; Strategic Support; Airborne Early Warning and Control; Radar Evaluation ;.He11cop~er...missions. (EI) Test: Aircraft assigned to evaluate the aircraft and/or its components installed as standard equipment. (EH) Test Support: Aircraft... consumables under two AF-GEN sub-projects: PROJECT SEAWEED and PROJECT NIGHT LIFE & FLYAWAY KITS. Also included in this section is data on ammunition

Evaluation of SAGE Electrochromic Devices: Cooperative Research and Development Final Report, CRADA Number CRD-15-579

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tenent, Robert C.

2017-12-06

NREL will conduct durability testing of Sage Electrochromics dynamic windows products using American Society for Testing and Materials (ASTM) standard methods and drive parameters as defined by Sage. Window units will be tested and standard analysis performed. Data will be summarized and reported back to Sage at the end of the testing period.

Determination of minimum suction level necessary for field dental units.

PubMed

Charlton, David G

2010-04-01

A significant problem with most field dental units is that their suction is too weak to effectively remove debris from the mouth. The purpose of this study was to determine the minimum clinically acceptable suction level for routine dentistry. A vacuum pump was connected to a high-volume dental evacuation line in a simulated clinical setting and different suction airflow rates were evaluated by nine evaluator dentists for their capability to effectively remove amalgam debris and water. Airflow levels were rated as "clinically acceptable" or "clinically unacceptable" by each evaluator. Data were analyzed using a chi2 test for trend. Analysis indicated a significant linear trend between airflow and ratings (p < 0.0001). The first airflow level considered by all evaluators as producing clinically acceptable suction was 4.5 standard cubic feet per minute (0.127 standard cubic meters per minute). This value should be the minimum level required for all military field dental units.

Cost evaluation of cardiovascular magnetic resonance versus coronary angiography for the diagnostic work-up of coronary artery disease: application of the European Cardiovascular Magnetic Resonance registry data to the German, United Kingdom, Swiss, and United States health care systems.

PubMed

Moschetti, Karine; Muzzarelli, Stefano; Pinget, Christophe; Wagner, Anja; Pilz, Günther; Wasserfallen, Jean-Blaise; Schulz-Menger, Jeanette; Nothnagel, Detle; Dill, Torsten; Frank, Herbert; Lombardi, Massimo; Bruder, Oliver; Mahrholdt, Heiko; Schwitter, Jürg

2012-06-14

Cardiovascular magnetic resonance (CMR) has favorable characteristics for diagnostic evaluation and risk stratification of patients with known or suspected CAD. CMR utilization in CAD detection is growing fast. However, data on its cost-effectiveness are scarce. The goal of this study is to compare the costs of two strategies for detection of significant coronary artery stenoses in patients with suspected coronary artery disease (CAD): 1) Performing CMR first to assess myocardial ischemia and/or infarct scar before referring positive patients (defined as presence of ischemia and/or infarct scar to coronary angiography (CXA) versus 2) a hypothetical CXA performed in all patients as a single test to detect CAD. A subgroup of the European CMR pilot registry was used including 2,717 consecutive patients who underwent stress-CMR. From these patients, 21% were positive for CAD (ischemia and/or infarct scar), 73% negative, and 6% uncertain and underwent additional testing. The diagnostic costs were evaluated using invoicing costs of each test performed. Costs analysis was performed from a health care payer perspective in German, United Kingdom, Swiss, and United States health care settings. In the public sectors of the German, United Kingdom, and Swiss health care systems, cost savings from the CMR-driven strategy were 50%, 25% and 23%, respectively, versus outpatient CXA. If CXA was carried out as an inpatient procedure, cost savings were 46%, 50% and 48%, respectively. In the United States context, cost savings were 51% when compared with inpatient CXA, but higher for CMR by 8% versus outpatient CXA. This analysis suggests that from an economic perspective, the use of CMR should be encouraged as a management option for patients with suspected CAD.

Evaluation of patients with methamphetamine- and cocaine-related chest pain in a chest pain observation unit.

PubMed

Diercks, Deborah B; Kirk, J Douglas; Turnipseed, Samuel D; Amsterdam, Ezra A

2007-12-01

Risk of acute coronary events in patients with methamphetamine and cocaine intoxication has been described. Little is known about the need for additional evaluation in these patients who do not have evidence of myocardial infarction after the initial emergency department evaluation. We herein describe our experience with these patients in a chest pain unit (CPU) and the rate of cardiac-related chest pain in this group. Retrospective analysis of patients evaluated in our CPU from January 1, 2000 to December 16, 2004 with a history of chest pain. Patients who had a positive urine toxicologic screen for methamphetamine or cocaine were included. No patients had ECG or cardiac injury marker evidence of myocardial infarction or ischemia during the initial emergency department evaluation. A diagnosis of cardiac-related chest pain was based upon positive diagnostic testing (exercise stress testing, nuclear perfusion imaging, stress echocardiography, or coronary artery stenosis >70%). During the study period, 4568 patients were evaluated in the CPU. A total of 1690 (37%) of patients admitted to the CPU underwent urine toxicologic testing. The result of urine toxicologic test was positive for cocaine or methamphetamine in 224 (5%). In the 2871 patients who underwent diagnostic testing for coronary artery disease (CAD), 401 (14%) were found to have positive results. There was no difference in the prevalence of CAD between those with positive result for toxicology screens (26/156, 17%) and those without (375/2715, 13%, RR 1.2, 95% CI 0.8-1.7). These findings suggest a relatively high rate of CAD in patients with methamphetamine and cocaine use evaluated in a CPU.

Hermetic Seal Leak Detection Apparatus

NASA Technical Reports Server (NTRS)

Kelley, Anthony R. (Inventor)

2013-01-01

The present invention is a hermetic seal leak detection apparatus, which can be used to test for hermetic seal leaks in instruments and containers. A vacuum tight chamber is created around the unit being tested to minimize gas space outside of the hermetic seal. A vacuum inducing device is then used to increase the gas chamber volume inside the device, so that a slight vacuum is pulled on the unit being tested. The pressure in the unit being tested will stabilize. If the stabilized pressure reads close to a known good seal calibration, there is not a leak in the seal. If the stabilized pressure reads closer to a known bad seal calibration value, there is a leak in the seal. The speed of the plunger can be varied and by evaluating the resulting pressure change rates and final values, the leak rate/size can be accurately calculated.

Itegrated Test and Evaluation of a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removtal System (CDRA), Mechanical Compressor Engineering Development Unit (EDU), and Sabitier Engineering Development Unit (EDU)

NASA Technical Reports Server (NTRS)

Knox, James C.; Campbell, Melissa; Murdoch, Karen; Miller, Lee A.; Jeng, Frank

2005-01-01

Currently on the International Space Station s (ISS) U.S. Segment, carbon dioxide (CO2) scrubbed from the cabin by a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removal Assembly (CDRA) is vented overboard as a waste product. Likewise, the product hydrogen (H2) that will be generated by the Oxygen Generation Assembly (OGA) planned for installation will also be vented. A flight experiment has been proposed that will take the waste CO2 removed from the cabin, and via the catalytic Sabatier process, reduce it with waste H2 to generate water and methane. The water produced may provide cost and logistics savings for ISS by reducing the amount of water periodically re-supplied to orbit. To make this concept viable, a mechanical piston compressor and accumulator were developed for collecting and storing the CO2 from the CDRA. The compressor, accumulator and Sabatier system would be packaged together as one unit and referred to as the Carbon Dioxide Reduction Assembly (CRA). Testing was required to evaluate the performance of a 4BMS CDRA, compressor, accumulator, and Sabatier performance along with their operating rules when integrated together. This had been numerically modeled and simulated; however, testing was necessary to verify the results from the engineering analyses. Testing also allowed a better understanding of the practical inefficiencies and control issues involved in a fully integrated system versus the theoretical ideals in the model. This paper presents and discusses the results of an integrated engineering development unit test.

Evaluation and comparison of ERTS measurements of major crops and soil associations for selected test sites in the central United States. [Texas, Indiana, Kansas, Iowa, Nebraska, and North Dakota

NASA Technical Reports Server (NTRS)

Baumgardner, M. F. (Principal Investigator)

1974-01-01

The author has identified the following significant results. Multispectral scanner data obtained by ERTS-1 over six test sites in the Central United States were analyzed and interpreted. ERTS-1 data for some of the test sites were geometrically corrected and temporally overlayed. Computer-implemented pattern recognition techniques were used in the analysis of all multispectral data. These techniques were used to evaluate ERTS-1 data as a tool for soil survey. Geology maps and land use inventories were prepared by digital analysis of multispectral data. Identification and mapping of crop species and rangelands were achieved throught the analysis of 1972 and 1973 ERTS-1 data. Multiple dates of ERTS-1 data were examined to determine the variation with time of the areal extent of surface water resources on the Southern Great Plain.

Test and evaluation of a multifunction keyboard and a dedicated keyboard for control of a flight management computer

NASA Technical Reports Server (NTRS)

Crane, J. M.; Boucek, G. P., Jr.; Smith, W. D.

1986-01-01

A flight management computer (FMC) control display unit (CDU) test was conducted to compare two types of input devices: a fixed legend (dedicated) keyboard and a programmable legend (multifunction) keyboard. The task used for comparison was operation of the flight management computer for the Boeing 737-300. The same tasks were performed by twelve pilots on the FMC control display unit configured with a programmable legend keyboard and with the currently used B737-300 dedicated keyboard. Flight simulator work activity levels and input task complexity were varied during each pilot session. Half of the points tested were previously familiar with the B737-300 dedicated keyboard CDU and half had no prior experience with it. The data collected included simulator flight parameters, keystroke time and sequences, and pilot questionnaire responses. A timeline analysis was also used for evaluation of the two keyboard concepts.

Field of Vision - Vehicles

DTIC Science & Technology

2017-05-11

NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) US Army Aberdeen Test Center (TEDT-AT-WFS) 400...AND ADDRESS(ES) Policy and Standardization Division (CSTE-TM) U.S. Army Test and Evaluation Command 2202 Aberdeen Boulevard Aberdeen Proving Ground

Decentralizing Centralized Control: Reorienting a Fundamental Tenet for Resilient Air Operation

DTIC Science & Technology

2008-05-22

Forward Air Controller FBIS Foreign Broadcast Information Service FCC Functional Component Commander FM Field Manual GBU - 39 Guided Bomb Unit - 39...Diameter Bomb ( GBU - 39 ) TEG Test and Evaluation Group TST Time Sensitive Target UAV Unmanned Aerial Vehicle USAF United States Air Force USAFWS United...www.afmc.af.mil/news/story.asp?id=123017916 (accessed November 11, 2007). Recent fielding of the GBU - 39 , Small Diameter Bomb (SDB), enables a

Acute hepatitis B virus window-period blood donations detected by individual-donation nucleic acid testing: a report on the first two cases found and interdicted in Spain.

PubMed

González, Rocio; Echevarria, José Manuel; Avellón, Ana; Barea, Luisa; Castro, Emma

2006-07-01

Mathematical models predict that, in Spain, a significant number of blood units will be obtained during the window period of the hepatitis B virus (HBV) infection. Routine nucleic acid testing (NAT) on individual blood units may provide experimental data to evaluate such a theoretical risk. Between February and July 2005, a total of 34,631 individual units were screened for HBV DNA by a multiplex transcription-mediated amplification (TMA) test. Units that repeatedly reacted in the test, but did not react for HBV surface antigen (HBsAg), were submitted to additional testing by both molecular and conventional assays, and the donors were recalled for follow-up studies and the collection of clinical and epidemiologic data. Confirmatory testing and follow-up studies identified 2 blood units donated during the HBV infection window period (1/17,316 units studied). Sequencing of amplification products obtained by nested polymerase chain reaction (n-PCR) revealed two HBV strains from genotypes D/ayw3 and F/adw4q-, but did not identify HBsAg mutants. The HBV DNA concentration in the index donations was estimated to be below the n-PCR detection level (180 IU/mL), in both cases. One donor developed acute hepatitis 2 months after donating blood, but the other remained asymptomatic and displayed normal alanine aminotransferase levels at follow-up. The HBV infection window period is a real issue in the setting of Spanish blood transfusions. NAT of individual units by TMA would make a significant contribution to improving the safety of the blood supply in Spain. Additional studies involving a larger number of units and longer periods of time are required, however, to ascertain the true incidence of the problem in this country.

Method calibration of the model 13145 infrared target projectors

NASA Astrophysics Data System (ADS)

Huang, Jianxia; Gao, Yuan; Han, Ying

2014-11-01

The SBIR Model 13145 Infrared Target Projectors ( The following abbreviation Evaluation Unit ) used for characterizing the performances of infrared imaging system. Test items: SiTF, MTF, NETD, MRTD, MDTD, NPS. Infrared target projectors includes two area blackbodies, a 12 position target wheel, all reflective collimator. It provide high spatial frequency differential targets, Precision differential targets imaged by infrared imaging system. And by photoelectricity convert on simulate signal or digital signal. Applications software (IR Windows TM 2001) evaluate characterizing the performances of infrared imaging system. With regards to as a whole calibration, first differently calibration for distributed component , According to calibration specification for area blackbody to calibration area blackbody, by means of to amend error factor to calibration of all reflective collimator, radiance calibration of an infrared target projectors using the SR5000 spectral radiometer, and to analyze systematic error. With regards to as parameter of infrared imaging system, need to integrate evaluation method. According to regulation with -GJB2340-1995 General specification for military thermal imaging sets -testing parameters of infrared imaging system, the results compare with results from Optical Calibration Testing Laboratory . As a goal to real calibration performances of the Evaluation Unit.

Evaluation and characterization of the methane-carbon dioxide decomposition reaction

NASA Technical Reports Server (NTRS)

Davenport, R. J.; Schubert, F. H.; Shumar, J. W.; Steenson, T. S.

1975-01-01

A program was conducted to evaluate and characterize the carbon dioxide-methane (CO2-CH4) decomposition reaction, i.e., CO2 + CH4 = 2C + 2H2O. The primary objective was to determine the feasibility of applying this reaction at low temperatures as a technique for recovering the oxygen (O2) remaining in the CO2 which exits mixed with CH4 from a Sabatier CO2 reduction subsystem (as part of an air revitalization system of a manned spacecraft). A test unit was designed, fabricated, and assembled for characterizing the performance of various catalysts for the reaction and ultraviolet activation of the CH4 and CO2. The reactor included in the test unit was designed to have sufficient capacity to evaluate catalyst charges of up to 76 g (0.17 lb). The test stand contained the necessary instrumentation and controls to obtain the data required to characterize the performance of the catalysts and sensitizers tested: flow control and measurement, temperature control and measurement, product and inlet gas analysis, and pressure measurement. A product assurance program was performed implementing the concepts of quality control and safety into the program effort.

Functional Evaluation of the Reusable JuniorSTAR® Half-Unit Insulin Pen.

PubMed

Klonoff, David; Nayberg, Irina; Rabbone, Ivana; Domenger, Catherine; Stauder, Udo; Oualali, Hamid; Danne, Thomas

2015-05-01

The functional performance of the JuniorSTAR(®) (Sanofi, Paris, France) half-unit insulin pen was evaluated through a series of specific objective tests to assess the dose accuracy, pen weight, injection force, and dialing torque. Pens (n = 60) were tested under standard atmospheric conditions with 3 different types of insulins manufactured by Sanofi (insulin glargine, insulin glulisine, and biphasic insulin isophane). The dose accuracy was tested according to the ISO 11608-1:2012 standards. Injection doses of 0.010, 0.155, and 0.300 ml were evaluated. For mean weight evaluation, the pens without the cartridge were weighed on precision balances. The injection force was measured using a texture analyzer and the dialing torque was measured using a torque meter. JuniorSTAR met the ISO 11608-1:2012 criteria for dose accuracy as all the delivered doses were within the predefined limits for all types of insulin tested. The mean weight of the JuniorSTAR pen was 33.4 g (SD = 0.075). The mean injection force was 6.0 N (SD = 0.8), 4.3 N (SD = 0.4), and 5.1 N (SD = 0.6) for insulin glargine, insulin glulisine, and biphasic insulin isophane, respectively. The mean dialing torque was 5.09 Ncm (SD = 0.29) and 5.88 Ncm (SD = 0.53) for setting and correcting a dose, respectively. Together with results from a previously reported usability survey, these results show that the JuniorSTAR reusable, half-unit pen is a lightweight and accurate device for insulin delivery with a dialing torque and injection force suitable for young people with type 1 diabetes. © 2015 Diabetes Technology Society.

Functional Evaluation of the Reusable JuniorSTAR® Half-Unit Insulin Pen

PubMed Central

Klonoff, David; Nayberg, Irina; Rabbone, Ivana; Domenger, Catherine; Stauder, Udo; Oualali, Hamid; Danne, Thomas

2015-01-01

Background: The functional performance of the JuniorSTAR® (Sanofi, Paris, France) half-unit insulin pen was evaluated through a series of specific objective tests to assess the dose accuracy, pen weight, injection force, and dialing torque. Method: Pens (n = 60) were tested under standard atmospheric conditions with 3 different types of insulins manufactured by Sanofi (insulin glargine, insulin glulisine, and biphasic insulin isophane). The dose accuracy was tested according to the ISO 11608-1:2012 standards. Injection doses of 0.010, 0.155, and 0.300 ml were evaluated. For mean weight evaluation, the pens without the cartridge were weighed on precision balances. The injection force was measured using a texture analyzer and the dialing torque was measured using a torque meter. Results: JuniorSTAR met the ISO 11608-1:2012 criteria for dose accuracy as all the delivered doses were within the predefined limits for all types of insulin tested. The mean weight of the JuniorSTAR pen was 33.4 g (SD = 0.075). The mean injection force was 6.0 N (SD = 0.8), 4.3 N (SD = 0.4), and 5.1 N (SD = 0.6) for insulin glargine, insulin glulisine, and biphasic insulin isophane, respectively. The mean dialing torque was 5.09 Ncm (SD = 0.29) and 5.88 Ncm (SD = 0.53) for setting and correcting a dose, respectively. Conclusions: Together with results from a previously reported usability survey, these results show that the JuniorSTAR reusable, half-unit pen is a lightweight and accurate device for insulin delivery with a dialing torque and injection force suitable for young people with type 1 diabetes. PMID:25633967

Evaluation of biogas production potential by dry anaerobic digestion of switchgrass--animal manure mixtures.

PubMed

Ahn, H K; Smith, M C; Kondrad, S L; White, J W

2010-02-01

Anaerobic digestion is a biological method used to convert organic wastes into a stable product for land application with reduced environmental impacts. The biogas produced can be used as an alternative renewable energy source. Dry anaerobic digestion [>15% total solid (TS)] has an advantage over wet digestion (<10% TS) because it allows for the use of a smaller volume of reactor and because it reduces wastewater production. In addition, it produces a fertilizer that is easier to transport. Performance of anaerobic digestion of animal manure-switchgrass mixture was evaluated under dry (15% TS) and thermophilic conditions (55 degrees C). Three different mixtures of animal manure (swine, poultry, and dairy) and switchgrass were digested using batch-operated 1-L reactors. The swine manure test units showed 52.9% volatile solids (VS) removal during the 62-day trial, while dairy and poultry manure test units showed 9.3% and 20.2%, respectively. Over the 62 day digestion, the swine manure test units yielded the highest amount of methane 0.337 L CH4/g VS, while the dairy and poultry manure test units showed very poor methane yield 0.028 L CH4/g VS and 0.002 L CH4/g VS, respectively. Although dairy and poultry manure performed poorly, they may still have high potential as biomass for dry anaerobic digestion if appropriate designs are developed to prevent significant volatile fatty acid (VFA) accumulation and pH drop.

Comparison of the heat generation of light curing units.

PubMed

Bagis, Bora; Bagis, Yildirim; Ertas, Ertan; Ustaomer, Seda

2008-02-01

The aim of this study was to evaluate the heat generation of three different types of light curing units. Temperature increases were recorded from a distance of 1 mm from a thermocouple to the tip of three different types of light curing units including one quartz-tungsten halogen (QTH), one plasma arc (PAC), and one light emitting diode (LED) unit. An experimental model was designed to fix the 1 mm distance between the tip of the light curing units and the thermocouple wire. Temperature changes were recorded in 10 second intervals up to 40 seconds. (10, 20, 30, and 40 seconds). Temperature measurements were repeated three times for every light curing unit after a one hour standby period. Statistical analysis of the results was performed using the analysis of variance (ANOVA) and the Bonferroni Test. The highest temperature rises (54.4+/-1.65 degrees C) occurred during activation of a PAC light curing unit for every test period (p<.05). The least temperature increase (11.8+/-1.3 degrees C) occurred with a LED curing unit for each tested period except for the measurement of the temperature rise using the QTH curing unit at the tenth second interval (p<.05). These results indicate the choice of light activation unit and curing time is important when polymerizing light activated resin based restorations to avoid any thermal damage to the pulp.

Science Library of Test Items. Volume Twenty-Three. Geology (Part One). Free Response Testing Program.

ERIC Educational Resources Information Center

Hopley, Ken; And Others

The first of several planned volumes of Free Response Test Items contains geology questions developed by the Assessment and Evaluation Unit of the New South Wales Department of Education. Two additional geology volumes and biology and chemistry volumes are in preparation. The questions in this volume were written and reviewed by practicing…

Science Library of Test Items. Volume Two.

ERIC Educational Resources Information Center

New South Wales Dept. of Education, Sydney (Australia).

The second volume of test items in the Science Library of Test Items is intended as a resource to assist teachers in implementing and evaluating science courses in the first 4 years of Australian secondary school. The items were selected from questions submitted to the School Certificate Development Unit by teachers in New South Wales. Only the…

Lab Procedures. Sludge Treatment and Disposal Course #166. Instructor's Guide [and] Student Workbook.

ERIC Educational Resources Information Center

Carnegie, John W.

Laboratory tests used to determine status and to evaluate and/or maintain process control of the various sludge treatment processes are introduced in this lesson. Neither detailed test procedures nor explanations of how the tests should be applied to every unit are explained; this information is provided in other modules. The instructor's manual…

SIRU utilization. Volume 1: Theory, development and test evaluation

NASA Technical Reports Server (NTRS)

Musoff, H.

1974-01-01

The theory, development, and test evaluations of the Strapdown Inertial Reference Unit (SIRU) are discussed. The statistical failure detection and isolation, single position calibration, and self alignment techniques are emphasized. Circuit diagrams of the system components are provided. Mathematical models are developed to show the performance characteristics of the subsystems. Specific areas of the utilization program are identified as: (1) error source propagation characteristics and (2) local level navigation performance demonstrations.

Effort to test, evaluate and deploy technologies to automate the measurement of real-time border wait times at United States-Canada land border crossings.

DOT National Transportation Integrated Search

2011-09-01

The United States and Canada share the largest bi-national trading relationship in the world. An efficient and cost-effective border crossing system for both freight and passenger vehicle traffic is thus vital to the economic well-being and security ...

Innovations: The Social Consequences of Science and Technology. Final Evaluation Report.

ERIC Educational Resources Information Center

Tolman, Richard R.

The Biological Sciences Curriculum Study designed, developed, and field-tested a series of nine curriculum resource units for a semester program called "Innovations: The Social Consequences of Science and Technology (IST)." The units were designed for use by students and teachers in the 11th and 12th grades and at the junior college…

Test of four stand growth simulators for the northeastern United States

Treesearch

Thomas M. Schuler; David A. Marquis; Richard L. Ernst; Brian T. Simpson; Brian T. Simpson

1993-01-01

Evaluates SILVAH, FIBER, NE-TWIGS, and OAKSIM, simulators commonly used in the northeastern United States, by comparing predicted stand development with actual stand development records for periods ranging from 15 to 50 years. Results varied with stand parameter, forest type, projection length, and geographic area. Except in the spruce-fir forest type where FIBER...

Energy and Agriculture. A Basic Core Curriculum for Teaching Energy to Vocational Agriculture Students.

ERIC Educational Resources Information Center

Albracht, James; French, Byron

This core curriculum contains five units of material for teaching energy to vocational agriculture students. Energy uses and the benefits of energy conservation are covered in a unit on the impact of energy on agriculture. Discussed next are tractor performance and Nebraska tractor test data for selecting and evaluating tractors for maximum fuel…

Spray drift reduction evaluations of spray nozzles using a standardized testing protocol

USDA-ARS?s Scientific Manuscript database

The development and testing of drift reduction technologies has come to the forefront of application research in the past few years in the United States. Drift reduction technologies (DRTs) can be spray nozzles, sprayer modifications, spray delivery assistance, spray property modifiers (adjuvants),...

Technical Evaluation Report

DTIC Science & Technology

2006-10-01

measuring unit and the control computer have been flight tested using both a small UAV and the PRP-560 “ Ranger ” patrol and rescue hovercraft, which...version based on the G9- Galaxy ram air parachute. Recently, in an effort to further extend the system’s payload capacity, developmental flight tests

Field Testing of Compartmentalization Methods for Multifamily Construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, K.; Lstiburek, J.

The 2012 IECC has an airtightness requirement of 3 air changes per hour at 50 Pascals test pressure for both single-family and multifamily construction in Climate Zones 3-8. Other programs (LEED, ASHRAE 189, ASHRAE 62.2) have similar or tighter compartmentalization requirements, driving the need for easier and more effective methods of compartmentalization in multifamily buildings. Builders and practitioners have found that fire-resistance rated wall assemblies are a major source of difficulty in air sealing/compartmentalization, particularly in townhouse construction. This problem is exacerbated when garages are “tucked in” to the units and living space is located over the garages. In thismore » project, Building Science Corporation examined the taping of exterior sheathing details to improve air sealing results in townhouse and multifamily construction, when coupled with a better understanding of air leakage pathways. Current approaches are cumbersome, expensive, time consuming, and ineffective; these details were proposed as a more effective and efficient method. The effectiveness of these air sealing methods was tested with blower door testing, including “nulled” or “guarded” testing (adjacent units run at equal test pressure to null out inter-unit air leakage, or “pressure neutralization”). Pressure diagnostics were used to evaluate unit-to-unit connections and series leakage pathways (i.e., air leakage from exterior, into the fire-resistance rated wall assembly, and to the interior).« less

Method for evaluating wind turbine wake effects on wind farm performance

NASA Technical Reports Server (NTRS)

Neustadter, H. E.; Spera, D. A.

1985-01-01

A method of testing the performance of a cluster of wind turbine units an data analysis equations are presented which together form a simple and direct procedure for determining the reduction in energy output caused by the wake of an upwind turbine. This method appears to solve the problems presented by data scatter and wind variability. Test data from the three-unit Mod-2 wind turbine cluster at Goldendale, Washington, are analyzed to illustrate the application of the proposed method. In this sample case the reduction in energy was found to be about 10 percent when the Mod-2 units were separated a distance equal to seven diameters and winds were below rated.

Cross-Cultural Validity of the Ruminative Responses Scale in Argentina and the United States.

PubMed

Arana, Fernán G; Rice, Kenneth G

2017-09-01

Although frequently used in the United States, the Ruminative Response Scale (RRS) has not been extensively studied in cross-cultural samples. The present study evaluated the factor structure of Treynor et al.'s 10-item version of the RRS in samples from Argentina ( N = 308) and the United States ( N = 371). In addition to testing measurement invariance between the countries, we evaluated whether the maladaptive implications of rumination were weaker for the Argentinians than for the U.S. group. Self-critical perfectionism was the criterion in those tests. Partial scalar invariance supported an 8-item version of the RRS. There were no differences in factor means or factor correlations in RRS dimensions between countries. Brooding and Reflection were positively correlated with self-critical perfectionism in both countries, with no significant differences in the sizes of these relations between the two samples. Results are discussed in terms of psychometric and cross-cultural implications for rumination.

Evaluating Effects of Heat Stress on Cognitive Function among Workers in a Hot Industry.

PubMed

Mazloumi, Adel; Golbabaei, Farideh; Mahmood Khani, Somayeh; Kazemi, Zeinab; Hosseini, Mostafa; Abbasinia, Marzieh; Farhang Dehghan, Somayeh

2014-01-01

Heat stress, as one of the most common occupational health problems, can impair operators' cognitive processes. The aim of this study was to evaluate the impact of thermal stress on cognitive function among workers in a hot industry. In this cross-sectional study conducted in Malibel Saipa Company in 2013, workers were assigned into two groups: one group were exposed to heat stress (n=35), working in casting unit and the other group working in machining unit (n=35) with a normal air conditioning. Wet Bulb Globe Temperature was measured at three heights of ankle, abdomen, and head. In order to evaluate the effects of heat stress on attention and reaction time, Stroop tests 1, 2, and 3 were conducted before starting the work and during the work. A significant positive correlation was observed between WBGT and test duration (P=0.01) and reaction time of Stroop test 3 (P=0.047), and between number of errors in Stroop tests 1, 2, and 3, during the work (P= 0.001). Moreover, Stroop test 3 showed a significant higher score for both test duration and reaction time of workers in case group. RESULTS of the present study, conducted in a real work environment, confirmed the impairment of cognitive functions, including selective attention and reaction time, under heat stress conditions.

Accurate monitoring leads to effective control and greater learning of patient education materials.

PubMed

Rawson, Katherine A; O'Neil, Rochelle; Dunlosky, John

2011-09-01

Effective management of chronic diseases (e.g., diabetes) can depend on the extent to which patients can learn and remember disease-relevant information. In two experiments, we explored a technique motivated by theories of self-regulated learning for improving people's learning of information relevant to managing a chronic disease. Materials were passages from patient education booklets on diabetes from NIDDK. Session 1 included an initial study trial, Session 2 included self-regulated restudy, and Session 3 included a final memory test. The key manipulation concerned the kind of support provided for self-regulated learning during Session 2. In Experiment 1, participants either were prompted to self-test and then evaluate their learning before selecting passages to restudy, were shown the prompt questions but did not overtly self-test or evaluate learning prior to selecting passages, or were not shown any prompts and were simply given the menu for selecting passages to restudy. Participants who self-tested and evaluated learning during Session 2 had a small but significant advantage over the other groups on the final test. Secondary analyses provided evidence that the performance advantage may have been modest because of inaccurate monitoring. Experiment 2 included a group who also self-tested but who evaluated their learning using idea-unit judgments (i.e., by checking their responses against a list of key ideas from the correct response). Participants who self-tested and made idea-unit judgments exhibited a sizable advantage on final test performance. Secondary analyses indicated that the performance advantage was attributable in part to more accurate monitoring and more effective self-regulated learning. An important practical implication is that learning of patient education materials can be enhanced by including appropriate support for learners' self-regulatory processes. (c) 2011 APA, all rights reserved.

The Effect of Evaluator Attitudes on Subjective Ratings of Unit Structure in Phase II of the ’Restructuring of the Heavy Division’ Test

DTIC Science & Technology

1979-09-01

DIVISION" TEST Edwin R. Smutz ARI FIELD UNIT AT FORT HOOD, TEXAS C/ C,; U. S. Army Research Institute for the Behavioral and Social Sciences I Ir September... SCIENCES A Field Operating Agency under the Jurisdiction of the Deputy Chief of Staff for Personnel WILLIAM L. HAUSERi JOSEPH ZEIDNER Colonel, U S Army...Behavioral and Social Sciences . fj The findings in this report are not to be construed as an official Departmeint of the Army Position, unions so

Analysis and Evaluation of German Attainments and Research in the Liquid Rocket Engine Field. Volume 4. Propellant Injectors

DTIC Science & Technology

1951-02-01

they were ob- served at a given pressure drop in "cold" testing with water or unreacted propellants. heat-transfer considerations and the location of... water as a coolant in the main chamber. The Winkler injector was used.on a test unit developing a thrust of 220 lb and an exhaust ve- locity of 6370 ft... water . Provision was made for an igniter in the center of the injector. The relatively high performance reported for this unit does not seem to be

FITNESSGRAM[R] Administration: Tips for Educators

ERIC Educational Resources Information Center

Mosier, Brian

2012-01-01

The first national youth fitness evaluation conducted in the United States was in 1958. Since that time, schools have continued to administer fitness evaluations using a variety of tests with no national-level assessment of youth fitness [Institute of Medicine (IOM), 2012]. However, in September 2012, the Presidential Youth Fitness Program (PYFP)…

Interpreting Predictions from the SAPRC07 Mechanism Based on Regional and Continental Simulations

EPA Science Inventory

The SAPRC07T mechanism is implemented and evaluated in the CMAQ air quality model. The implementation is described and tested with simulations over the United States for two periods. The evaluation compares results against observations for ozone and particulate matter as well as ...

Evaluation of the I-95 Commercial Vehicle Operations Roadside Safety and SAFER Data Mailbox Field Operational Tests : Evaluation Report

DOT National Transportation Integrated Search

2002-03-29

In 1998, the United States experienced nearly 400,000 crashes involving large trucks, resulting in approximately 5,000 deaths. Although new research (e.g., the Large Truck Crash Causation Project) is being planned by the Federal Motor Carrier Safety ...

Ability Level Estimation of Students on Probability Unit via Computerized Adaptive Testing

ERIC Educational Resources Information Center

Özyurt, Hacer; Özyurt, Özcan

2015-01-01

Problem Statement: Learning-teaching activities bring along the need to determine whether they achieve their goals. Thus, multiple choice tests addressing the same set of questions to all are frequently used. However, this traditional assessment and evaluation form contrasts with modern education, where individual learning characteristics are…

Stress Reconstruction Analysis of Wheel Saw Cut Tests and Evaluation of Reconstruction Procedure

DOT National Transportation Integrated Search

1993-09-01

The report is the fourth in a series of engineering studies on railroad vehicle wheel performance. The results of saw cut tests performed on one new and one used wheel designed for a fleet of multiple unit (MU) power cars are summarized and analyzed....

Termiticide Field Tests - 1989 Update

Treesearch

Bradford M. Kard; Joe K. Mauldin

1993-01-01

For several years, organophosphate and pyrethroid termiticides have undergone field evaluation as treatments to soil for control of subterranean termites. These termiticides remained effective at some application rates for 5 or more years. Field data are reported for ground-board and concrete slab tests at sites in the continental United States. Generally, pyrethroids...

42 CFR 84.308 - Additional testing.

Code of Federal Regulations, 2013 CFR

2013-10-01

... §§ 84.304 through 84.307. These units will be evaluated for fire and explosion hazards using the tests....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National Personal Protection Technology Laboratory (NPPTL), Bruceton Research Center, 626 Cochrans Mill Road...

42 CFR 84.308 - Additional testing.

Code of Federal Regulations, 2014 CFR

2014-10-01

... §§ 84.304 through 84.307. These units will be evaluated for fire and explosion hazards using the tests....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National Personal Protection Technology Laboratory (NPPTL), Bruceton Research Center, 626 Cochrans Mill Road...

42 CFR 84.308 - Additional testing.

Code of Federal Regulations, 2012 CFR

2012-10-01

... §§ 84.304 through 84.307. These units will be evaluated for fire and explosion hazards using the tests....S.C. 552(a) and 1 CFR Part 51. All approved material is available for inspection at NIOSH, National Personal Protection Technology Laboratory (NPPTL), Bruceton Research Center, 626 Cochrans Mill Road...

Freeze-Testing in St. Augustinegrass II: Evaluation of acclimation effects

USDA-ARS?s Scientific Manuscript database

Winter survivability is a major-limiting factor for St. Augustinegrass (Stenotaphrum secundatum [Walt.] Kuntze) grown in the transition zone of the United States as cold winters can result in high levels of winterkill. In addition to field studies, lab-based freeze tests mimicking field winter survi...

Evaluation Report for the Occupational Exploration Program. Pilot Test 1975.

ERIC Educational Resources Information Center

Lave, Janice; And Others

Pilot testing was conducted on parts of the Occupational Exploration Program (OEP), a classroom program designed to enhance the career awareness and career understandings of seventh and eighth grade students through simulations, games, and small group and individualized activities. The Introduction to Occupational Exploration unit and three…

Field test on the treatment of source zone chloroethenes using emulsified zerovalent iron

EPA Science Inventory

This talk summarizes the research activities currently underway at the Solid Waste Management Unit 45 (Site 45), Marine Corps Recruit Depot, Parris Island, South Carolina. A pilot field test was initiated in 2005 at this site to evaluate the effectiveness of nanoscale emulsified...

Creatinine - urine

MedlinePlus

... test can be used for the following: To evaluate how well the kidneys are working As part ... the tubule cells Kidney failure Too little blood flow to the kidneys, damage to filtering units Kidney ...

Evaluation of fit of cement-retained implant-supported 3-unit structures fabricated with direct metal laser sintering and vacuum casting techniques.

PubMed

Oyagüe, Raquel Castillo; Sánchez-Turrión, Andrés; López-Lozano, José Francisco; Montero, Javier; Albaladejo, Alberto; Suárez-García, María Jesús

2012-07-01

This study evaluated the vertical discrepancy of implant-fixed 3-unit structures. Frameworks were constructed with laser-sintered Co-Cr, and vacuum-cast Co-Cr, Ni-Cr-Ti, and Pd-Au. Samples of each alloy group were randomly luted in standard fashion using resin-modified glass-ionomer, self-adhesive, and acrylic/urethane-based cements (n = 12 each). Discrepancies were SEM analyzed. Three-way ANOVA and Student-Newman-Keuls tests were run (P < 0.05). Laser-sintered structures achieved the best fit per cement tested. Within each alloy group, resin-modified glass-ionomer and acrylic/urethane-based cements produced comparably lower discrepancies than the self-adhesive agent. The abutment position did not yield significant differences. All misfit values could be considered clinically acceptable.

Design and development of FZU-32/B bomb fuze initiator. Final report 23 Jun 72--15 Nov 73

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miazza, J.

1974-05-01

The primary objective of this program was to develop a cost effective, production engineered FZU-24/B Bomb Fuze Initiator. The initiator is an electric generating device which, when installed in the fuze charging well of general purpose bombs, is capable of deriving energy from the airstream passing the bomb in free fall and converting the energy into electric energy suitable for powering a bomb fuze. The objective was to be accomplished by means of a production engineering effort carried through the evolution of design, fabrication, assembly, test, and evaluation. The baseline for the design was Harry Diamond Laboratories' Drawing No. 11716160.more » A quantity of 60 units was fabricated and tested, in accordance with the production engineered design. After some additional redesign to correct identified deficiencies, 220 units were fabricated. These units were subjected to environmental, wind tunnel, and flight testing and performance requirements were met. The final unit design was designated the FZU-32/B Bomb Fuze Initiator.« less

¡Sólo Se Vive Una Vez! (You Only Live Once): A Pilot Evaluation of Individually Tailored Video Modules Aiming to Increase HIV Testing Among Foreign-Born Latino Men.

PubMed

Dolwick Grieb, Suzanne M; Flores-Miller, Alejandra; Page, Kathleen R

2017-02-01

Although Latinos living in the United States are disproportionately affected by HIV, the development, implementation, and evaluation of HIV prevention, testing, and linkage to care interventions lag behind efforts occurring in other communities. To address sociocultural barriers to testing, we developed a multilevel intervention. This study is a pilot evaluation of the individual-level component of the intervention-animated video modules that address specific barriers to HIV testing common among foreign-born Latino men. We conducted a survey assessing HIV risk and barriers to testing with a convenience sample of 104 foreign-born Latino men in Baltimore, MD, who had not tested for HIV within the past year. Intention to test in the next 3 months was measured before and after viewing an intervention module selected based on survey responses. Fifty-two (50.0%) participants had never tested for HIV. Of the participants who had previously tested for HIV, the mean time since their last test was 3.48 years (SD = 3.55). Participants' intention to test for HIV significantly increased after watching the module (t = -8.28, P < 0.001). Increased intention to test was not associated with any socio-demographic characteristics (ie, age, country of origin) or reported sexual behaviors (ie, number of sex partners in the past year). These results suggest that our culturally sensitive, individually tailored intervention can be an additional tool to encourage HIV testing among previously untested foreign-born Latino men, one of the demographic groups at highest risk for delayed HIV diagnosis in the United States.

TESTING PRACTICES AND VOLUME OF NON-LYME TICKBORNE DISEASES IN THE UNITED STATES

PubMed Central

Connally, Neeta P.; Hinckley, Alison F.; Feldman, Katherine A.; Kemperman, Melissa; Neitzel, David; Wee, Siok-Bi; White, Jennifer L.; Mead, Paul S.; Meek, James I.

2015-01-01

Large commercial laboratories in the United States were surveyed regarding the number of specimens tested for eight tickborne diseases in 2008. Seven large commercial laboratories reported testing a total of 2,927,881 specimens nationally (including Lyme disease). Of these, 495,585 specimens (17 percent) were tested for tickborne diseases other than Lyme disease. In addition to large commercial laboratories, another 1,051 smaller commercial, hospital, and government laboratories in four states (CT, MD, MN, and NY) were surveyed regarding tickborne disease testing frequency, practices, and results. Ninety-two of these reported testing a total of 10,091 specimens for four tickborne diseases other than Lyme disease. We estimate the cost of laboratory diagnostic testing for non-Lyme disease tickborne diseases in 2008 to be $9.6 million. These data provide a baseline to evaluate trends in tickborne disease test utilization and insight into the burden of these diseases. PMID:26565931

Initial Evaluation of Acoustic Emission SHM of PRSEUS Multi-bay Box Tests

NASA Technical Reports Server (NTRS)

Horne, Michael R.; Madaras, Eric I.

2016-01-01

A series of tests of the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) HWB Multi-Bay Test Article were conducted during the second quarter of 2015 at NASA Langley Research Center (LaRC) in the Combined Loads Test facility (COLTS). This report documents the Acoustic Emission (AE) data collected during those tests along with an initial analysis of the data. A more detailed analysis will be presented in future publications.

Evaluation of Erosion Potential of Estuarine Sediments in NY/NJ Harbor (Impact of In-Situ Stabilization on the Remediation of Soft Sediments - A preamble to Erosion Testing and Evaluation)

DOT National Transportation Integrated Search

2011-09-01

The primary objective of the project are to perform a review of existing in-situ techniques of sediment erosion potential evaluation in contaminated "superfund" sites in the United States and those from Europe and Japan and the applicability of soft ...

Parabolic dish test site: History and operating experience

NASA Technical Reports Server (NTRS)

Selcuk, M. K. (Compiler)

1985-01-01

The parabolic dish test site (PDTS) was established for testing point-focusing solar concentrator systems operating at temperatures approaching 1650 C. Among tests run were evaluation and performance characterization of parabolic dish concentrators, receivers, power conversion units, and solar/fossil-fuel hybrid systems. The PDTS was fully operational until its closure in June, 1984. The evolution of the test program, a chronological listing of the experiments run, and data summaries for most of the tests conducted are presented.

Corrective Action Investigation Plan for Corrective Action Unit 375: Area 30 Buggy Unit Craters, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patrick Matthews

2010-03-01

Corrective Action Unit (CAU) 375 is located in Areas 25 and 30 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 375 comprises the two corrective action sites (CASs) listed below: • 25-23-22, Contaminated Soils Site • 30-45-01, U-30a, b, c, d, e Craters Existing information on the nature and extent of potential contamination present at the CAU 375 CASs is insufficient to evaluate and recommend corrective action alternatives (CAAs). This document details an investigation plan that will provide for the gathering of sufficient information to evaluate and recommend CAAs. Correctivemore » Action Site 25-23-22 is composed of the releases associated with nuclear rocket testing at Test Cell A (TCA). Test Cell A was used to test and develop nuclear rocket motors as part of the Nuclear Rocket Development Station from its construction in 1958 until 1966, when rocket testing began being conducted at Test Cell C. The rocket motors were built with an unshielded nuclear reactor that produced as much as 1,100 kilowatts (at full power) to heat liquid hydrogen to 4,000 degrees Fahrenheit, at which time the expanded gases were focused out a nozzle to produce thrust. The fuel rods in the reactor were not clad and were designed to release fission fragments to the atmosphere, but due to vibrations and loss of cooling during some operational tests, fuel fragments in excess of planned releases became entrained in the exhaust and spread in the immediate surrounding area. Cleanup efforts have been undertaken at times to collect the fuel rod fragments and other contamination. Previous environmental investigations in the TCA area have resulted in the creation of a number of use restrictions. The industrial area of TCA is encompassed by a fence and is currently posted as a radioactive material area. Corrective Action Site 30-45-01 (releases associated with the Buggy Plowshare test) is located in Area 30 on Chukar Mesa. It was a Plowshare test where five nuclear devices were buried 140 feet (ft) deep in a row at 150-ft intervals. These devices were detonated on March 12, 1968, to produce a trench 254 ft wide, 865 ft long, and 70 ft deep. The mesa where the test was conducted is surrounded on three sides by ravines, and the entire end of the mesa is fenced and posted as a contamination area. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend CAAs. Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on December 2, 2009, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 375.« less

Annual Progress Report, FY 1980, 1 October 1979 - 30 September 1980,

DTIC Science & Technology

1980-10-01

coordinating an integrated pest management program, and constructing initial pilot prototypes, test models, and pro- ducing limited quantities of medical...Screening Test Based on the Ventilatory Responses of Fish . . . . . . . a & a . . . . 25 Chemistry and Molecular Biology of the Disinfection Process...Sink Unit, Surgical, Field (NSN 6545-00-935-4056), Engineering Evaluation of . . . . . . . . . . . . . . . . . . 69 Technical Feasibility Testing (TFT

The Influence of Test-Based Accountability Policies on Teacher Stress and Instructional Practices: A Moderated Mediation Model

ERIC Educational Resources Information Center

von der Embse, Nathaniel P.; Schoemann, Alexander M.; Kilgus, Stephen P.; Wicoff, Maribeth; Bowler, Mark

2017-01-01

The present study examined the use of student test performance for merit pay and teacher evaluation as predictive of both educator stress and counterproductive teaching practices, and the moderating role of perceived test value. Structural equation modelling of data from a sample of 7281 educators in a South-eastern state in the United States…

Implementation, reliability testing, and compliance monitoring of the Confusion Assessment Method for the Intensive Care Unit (CAM-ICU) in trauma patients

PubMed Central

Soja, Stacie L.; Pandharipande, Pratik P.; Fleming, Sloan B.; Cotton, Bryan A.; Miller, Leanna R.; Weaver, Stefanija G.; Lee, Byron T.; Ely, E. Wesley

2013-01-01

Objective To implement delirium monitoring, test reliability, and monitor compliance of performing the Confusion Assessment Method for the Intensive Care Unit (CAM-ICU) in trauma patients. Design and setting Prospective, observational study in a Level 1 trauma unit of a tertiary care, university-based medical center. Patients Acutely injured patients admitted to the trauma unit from February 1, 2006–April 16, 2006. Measurements and Results Following web-based teaching modules and group in-services, bedside nurses evaluated patients daily for depth of sedation with the Richmond Agitation-Sedation Scale (RASS) and for the presence of delirium with the CAM-ICU. On randomly assigned days over a 10-week period, evaluations by nursing staff were followed by evaluations by an expert evaluator of the RASS and the CAM-ICU, in order to assess compliance and reliability of the CAM-ICU in trauma patients. Following the audit period, the nurses completed a post-implementation survey. One thousand and eleven random CAM-ICU assessments were performed by the expert evaluator, within 1 hour of the bedside nurses’ assessments. Nurses completed the CAM-ICU assessments in 84% (849 of 1011) of evaluations. Overall agreement (κ) between nurses and the expert evaluator was 0.77 (0.721, 0.822; p<0.0001). In TBI patients κ was 0.75 (0.667, 0.829; p<0.0001), while in mechanically-ventilated patients κ was 0.62 (0.534, 0.704; p<0.0001). The survey revealed nurses were confident in performing the CAM-ICU, realized the importance of delirium, and were satisfied with the training they received. The survey also acknowledged obstacles to implementation including nursing time and failure of physicians/surgeons to address treatment approaches for delirium. Conclusions The CAM-ICU can be successfully implemented in a university-based trauma unit with high compliance and reliability. Quality improvement projects seeking to implement delirium monitoring would be wise to address potential pitfalls including time complaints and the negative impact of physician indifference regarding this form of organ dysfunction. PMID:18297270

Fiber Optic Cable Feedthrough and Sealing

NASA Technical Reports Server (NTRS)

Fan, Robert J.

1998-01-01

A novel fiberoptic hermetic bulkhead feedthrough has been developed which will offer cryogenic sealing at leak rates of 10(exp -11) cc/sec helium. This feedthrough was developed for NASA in response to needs for a hermetically sealed feedthrough which could withstand a range of temperatures from low cryogenic (-196 C), due to liquid fuels and oxidizers, to high temperatures (+200 C) encountered in the proximity of combustion gasses. The development effort will be reported from conceptual design of single and multi-channel feedthrough units with single interconnection interfaces to units with double-ended interconnection interfaces. Various combinations of fiber/buffers are reported with recommendations based on test results. A comprehensive series of environmental and mechanical tests were performed to evaluate the feedthroughs in adverse conditions. Test results are reported including insertion loss, salt spray, sinusoidal vibration, random vibration, mechanical shock, thermal shock and humidity. A second set of feedthrough units was exposed to 3 different types of radiation. Optical transmittance changes during the tests were monitored and leak rate testing was done after each test. State-of-the-art technology in optical fiber feedthroughs constructed with polycrystalline ceramic is presented.

EMI/EMP Resistant Data Bus

DTIC Science & Technology

1976-09-01

Control Multiplex Terminal Unit (CMTU) 1 each MTU Test Set 2 each CMTU Test Set 1 each 9 port Radial Coupler 1 each Fiber Optics Radial...Introduction 3 2 . MTU 11 3. CMTU 1 ? 4. SSIU and Controller ?! 5. Optical Data Bus 21 II System Design Construction 24 1 . Optoelectronic...8217 TABLE OF CONTENTS (Continued) SECTION TITLE PAGE IV System Test and Operation 1 . Test Equipment 2 . Evaluation a. Optical Bus b. Optoelectronic

Exploratory Development Research Effectiveness: A Second Evaluation,

DTIC Science & Technology

1978-09-01

A12i 537 EXPLORATORY DEVELOPMENT RESERCH EFFECTIVENESS: A / SECOND EVRLUATfON(U) CALIFORNIA STATE UNIV SACRAMENTO T A BUCKLES ET AL. SEP 78 CSUS/NPS...Administration - CSUS-NPS J077091 ii TABLE OF CONTENTS ABSTRACT . OBJECTIVE.............. . .. .. .. .... 1 DISCUSSION............. .. .. .. .... 1... contention that Work Unit Cost influenced the degree of transition. The last postulate that was tested concerned work unit classification by dollar amount. It

Analysis of on-line clinical laboratory manuals and practical recommendations.

PubMed

Beckwith, Bruce; Schwartz, Robert; Pantanowitz, Liron

2004-04-01

On-line clinical laboratory manuals are a valuable resource for medical professionals. To our knowledge, no recommendations currently exist for their content or design. To analyze publicly accessible on-line clinical laboratory manuals and to propose guidelines for their content. We conducted an Internet search for clinical laboratory manuals written in English with individual test listings. Four individual test listings in each manual were evaluated for 16 data elements, including sample requirements, test methodology, units of measure, reference range, and critical values. Web sites were also evaluated for supplementary information and search functions. We identified 48 on-line laboratory manuals, including 24 academic or community hospital laboratories and 24 commercial or reference laboratories. All manuals had search engines and/or test indices. No single manual contained all 16 data elements evaluated. An average of 8.9 (56%) elements were present (range, 4-14). Basic sample requirements (specimen and volume needed) were the elements most commonly present (98% of manuals). The frequency of the remaining data elements varied from 10% to 90%. On-line clinical laboratory manuals originate from both hospital and commercial laboratories. While most manuals were user-friendly and contained adequate specimen-collection information, other important elements, such as reference ranges, were frequently absent. To ensure that clinical laboratory manuals are of maximal utility, we propose the following 13 data elements be included in individual test listings: test name, synonyms, test description, test methodology, sample requirements, volume requirements, collection guidelines, transport guidelines, units of measure, reference range, critical values, test availability, and date of latest revision.

Statistical Stationarity of Sediment Interbed Thicknesses in a Basalt Aquifer, Idaho National Laboratory, Eastern Snake River Plain, Idaho

USGS Publications Warehouse

Stroup, Caleb N.; Welhan, John A.; Davis, Linda C.

2008-01-01

The statistical stationarity of distributions of sedimentary interbed thicknesses within the southwestern part of the Idaho National Laboratory (INL) was evaluated within the stratigraphic framework of Quaternary sediments and basalts at the INL site, eastern Snake River Plain, Idaho. The thicknesses of 122 sedimentary interbeds observed in 11 coreholes were documented from lithologic logs and independently inferred from natural-gamma logs. Lithologic information was grouped into composite time-stratigraphic units based on correlations with existing composite-unit stratigraphy near these holes. The assignment of lithologic units to an existing chronostratigraphy on the basis of nearby composite stratigraphic units may introduce error where correlations with nearby holes are ambiguous or the distance between holes is great, but we consider this the best technique for grouping stratigraphic information in this geologic environment at this time. Nonparametric tests of similarity were used to evaluate temporal and spatial stationarity in the distributions of sediment thickness. The following statistical tests were applied to the data: (1) the Kolmogorov-Smirnov (K-S) two-sample test to compare distribution shape, (2) the Mann-Whitney (M-W) test for similarity of two medians, (3) the Kruskal-Wallis (K-W) test for similarity of multiple medians, and (4) Levene's (L) test for the similarity of two variances. Results of these analyses corroborate previous work that concluded the thickness distributions of Quaternary sedimentary interbeds are locally stationary in space and time. The data set used in this study was relatively small, so the results presented should be considered preliminary, pending incorporation of data from more coreholes. Statistical tests also demonstrated that natural-gamma logs consistently fail to detect interbeds less than about 2-3 ft thick, although these interbeds are observable in lithologic logs. This should be taken into consideration when modeling aquifer lithology or hydraulic properties based on lithology.

Evaluation, Analysis, and Documentation Support for the 10kW Signature Suppressed Lightweight Electric Energy Plant (SLEEP)

DTIC Science & Technology

1988-03-14

HAEMP. This issue will be resolved during the Technical Test. (8) Will the 10kW SLEEP handle brief overload conditions? Air conditioners and other...signal units; air defense units; combat arms command, control, and commnunications units; and logistics functions in the brigade area. Priority...Skid mounting o Lifting attachments and tiedowns o Transportable by USAF C-130, C-141 and all US Army aircraft o Capability for low velocity air drop

Corrective Action Investigation Plan for Corrective Action Unit 219: Septic Systems and Injection Wells, Nevada Test Site, Nevada, Rev. No.: 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

David A. Strand

The Corrective Action Investigation Plan for Corrective Action Unit 219, Septic Systems and Injection Wells, has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy, and the U.S. Department of Defense. The purpose of the investigation is to ensure that adequate data are collected to provide sufficient and reliable information to identify, evaluate, and select technically viable corrective actions. Corrective Action Unit 219 is located in Areas 3, 16, and 23 of the Nevada Test Site, which is 65 miles northwest ofmore » Las Vegas, Nevada. Corrective Action Unit 219 is comprised of the six Corrective Action Sites (CASs) listed below: (1) 03-11-01, Steam Pipes and Asbestos Tiles; (2) 16-04-01, Septic Tanks (3); (3) 16-04-02, Distribution Box; (4) 16-04-03, Sewer Pipes; (5) 23-20-01, DNA Motor Pool Sewage and Waste System; and (6) 23-20-02, Injection Well. These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives. Additional information will be obtained by conducting a corrective action investigation prior to evaluating corrective action alternatives and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document.« less

Guidelines for model calibration and application to flow simulation in the Death Valley regional groundwater system

USGS Publications Warehouse

Hill, M.C.; D'Agnese, F. A.; Faunt, C.C.

2000-01-01

Fourteen guidelines are described which are intended to produce calibrated groundwater models likely to represent the associated real systems more accurately than typically used methods. The 14 guidelines are discussed in the context of the calibration of a regional groundwater flow model of the Death Valley region in the southwestern United States. This groundwater flow system contains two sites of national significance from which the subsurface transport of contaminants could be or is of concern: Yucca Mountain, which is the potential site of the United States high-level nuclear-waste disposal; and the Nevada Test Site, which contains a number of underground nuclear-testing locations. This application of the guidelines demonstrates how they may be used for model calibration and evaluation, and also to direct further model development and data collection.Fourteen guidelines are described which are intended to produce calibrated groundwater models likely to represent the associated real systems more accurately than typically used methods. The 14 guidelines are discussed in the context of the calibration of a regional groundwater flow model of the Death Valley region in the southwestern United States. This groundwater flow system contains two sites of national significance from which the subsurface transport of contaminants could be or is of concern: Yucca Mountain, which is the potential site of the United States high-level nuclear-waste disposal; and the Nevada Test Site, which contains a number of underground nuclear-testing locations. This application of the guidelines demonstrates how they may be used for model calibration and evaluation, and also to direct further model development and data collection.

Do you have a well-designed organization?

PubMed

Goold, Michael; Campbell, Andrew

2002-03-01

For most companies, organization design is neither a science nor an art; it's an oxymoron. Organizational structures evolve in fits and starts, shaped more by politics than by policies. Although most executives can sense when their organization designs are not working well, few take meaningful action, partly because they lack a practical framework to guide them. The authors of this article provide just such a framework; they present nine tests that can be used to either evaluate an existing organization design or create a new one. Four "fit" tests offer an initial screen: The market advantage test asks whether a design directs sufficient management attention to the company's sources of competitive advantage; the parenting advantage test determines whether the design gives enough attention to the corporate-level activities that provide real value to the company; the people test shows whether the design reflects the employees' strengths; and the feasibility test looks at constraints that may impede implementation. Five "good design" tests can help a company refine its prospective design. The specialist cultures test ensures that there's sufficient insulation for units that need to be different from the prevailing culture; the difficult-links test determines whether a design offers solutions for potentially problematic unit-to-unit links; the redundant-hierarchy test asks whether the design has too many parent levels; the accountability test looks at whether every unit has suitable controls; and the flexibility test ensures that the design lets the company adapt to change. Once a design is altered, the tests should be repeated. Organizational decisions are inevitably complex, and tweaking one part of the design may produce unanticipated consequences elsewhere.

Development, implementation, and evaluation of an energy and power unit of instruction for junior high school industrial arts/technology education programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Litowitz, L.S.

The unit of instruction was developed and refined in three stages. In the first stage, potential objectives for the unit of instruction were identified from appropriate literature. The objectives were mailed to a group primarily consisting of IA/TE state supervisors for critiquing. Upon receiving responses from the critique group, a revised list of objectives was created. From this revised list a content framework was developed. The content framework was then submitted for critiquing to a second group primarily consisting of energy and power curriculum developers. The responses from the second critique group were summarized, and a refined content framework wasmore » produced. A series of twelve hand-on learning activities for junior high school students were then developed to fulfill the unit objectives and concepts identified in the content framework. These activities were critiqued by a final group of experts representing in-service junior high school IA/TE teachers. Revisions to the unit of instruction were made based on feedback from the final critique group. The unit of instruction was then implemented in a junior high school setting as a final means of obtaining formative evaluation. Results of the formative evaluation indicated that the students who participated in the field test had met many of the unit objectives. Recommendations as to the use of the unit of instruction were made.« less

A Multicomponent Fall Prevention Strategy Reduces Falls at an Academic Medical Center.

PubMed

France, Dan; Slayton, Jenny; Moore, Sonya; Domenico, Henry; Matthews, Julia; Steaban, Robin L; Choma, Neesha

2017-09-01

While the reduction in fall rates has not kept pace with the reduction of other hospital-acquired conditions, patient safety research and quality improvement (QI) initiatives at the system and hospital levels have achieved positive results and provide insights into potentially effective risk reduction strategies. An academic medical center developed a QI-based multicomponent strategy for fall prevention and pilot tested it for six months in three high-risk units-the Neuroscience Acute Care Unit, the Myelosuppression/Stem Cell Transplant Unit, and the Acute Care for the Elderly Unit-before implementing and evaluating the strategy hospitalwide. The multicomponent fall strategy was evaluated using a pre-post study design. The main outcome measures were falls and falls with harm measured in events per 1,000 patient-days. Fall rates were monitored and compared for three classes of falls: (1) accidental, (2) anticipated physiologic, and (3) unanticipated physiologic. Statistical process control charts showed that the pilot units had achieved significant reductions in falls with harm during the last five months of data collection. Wald test and segmented regression analyses revealed significant improvements in pooled postintervention fall rates, stratified by fall type. The hospitalwide implementation of the program resulted in a 47% overall reduction in falls in the postintervention period. A fall prevention strategy that targeted the spectrum of risk factors produced measurable improvement in fall rates and rates of patient harm. Hospitals must continue developing, rigorously testing, and sharing their results and experiences in implementing and sustaining multicomponent fall prevention strategies. Copyright © 2017 The Joint Commission. Published by Elsevier Inc. All rights reserved.

Estimating aquatic toxicity as determined through laboratory tests of great lakes sediments containing complex mixtures of environmental contaminants

USGS Publications Warehouse

1996-01-01

We developed and evaluated a total toxic units modeling approach for predicting mean toxicity as measured in laboratory tests for Great Lakes sediments containing complex mixtures of environmental contaminants (e.g., polychlorinated biphenyls, polycyclic aromatic hydrocarbons, pesticides, chlorinated dioxins, and metals). The approach incorporates equilibrium partitioning and organic carbon control of bioavailability for organic contaminants and acid volatile sulfide (AVS) control for metals, and includes toxic equivalency for planar organic chemicals. A toxic unit is defined as the ratio of the estimated pore-water concentration of a contaminant to the chronic toxicity of that contaminant, as estimated by U.S. Environmental Protection Agency Ambient Water Quality Criteria (AWQC). The toxic unit models we developed assume complete additivity of contaminant effects, are completely mechanistic in form, and were evaluated without any a posteriori modification of either the models or the data from which the models were developed and against which they were tested. A linear relationship between total toxic units, which included toxicity attributable to both iron and un-ionized ammonia, accounted for about 88% of observed variability in mean toxicity; a quadratic relationship accounted for almost 94%. Exclusion of either bioavailability components (i.e., equilibrium partitioning control of organic contaminants and AVS control of metals) or iron from the model substantially decreased its ability to predict mean toxicity. A model based solely on un-ionized ammonia accounted for about 47% of the variability in mean toxicity. We found the toxic unit approach to be a viable method for assessing and ranking the relative potential toxicity of contaminated sediments.

Context matters: the impact of unit leadership and empowerment on nurses' organizational commitment.

PubMed

Laschinger, Heather K Spence; Finegan, Joan; Wilk, Piotr

2009-05-01

The aim of this study was to test a multilevel model linking unit-level leader-member exchange quality and structural empowerment to nurses' psychological empowerment and organizational commitment at the individual level of analysis. Few studies have examined the contextual effects of unit leadership on individual nurse outcomes. Workplace empowerment has been related to retention outcomes such as organizational commitment in several studies, but few have studied the impact of specific unit characteristics within which nurses work on these outcomes. We surveyed 3,156 nurses in 217 hospital units to test the multilevel model. A multilevel path analysis revealed significant individual and contextual effects on nurses' organizational commitment. Both unit-level leader-member exchange quality and structural empowerment had significant direct effects on individual-level psychological empowerment and organizational commitment. Psychological empowerment mediated the relationship between core self-evaluations and organizational commitment at the individual level of analysis. The contextual effects of positive supervisor relationships and their influence on empowering working conditions at the unit level and, subsequently, nurses' organizational commitment highlight the importance of leadership for creating conditions that result in a committed nursing workforce.

Evaluation and Acceptability of a Simplified Test of Visual Function at Birth in a Limited-Resource Setting.

PubMed

Carrara, Verena I; Darakomon, Mue Chae; Thin, Nant War War; Paw, Naw Ta Kaw; Wah, Naw; Wah, Hser Gay; Helen, Naw; Keereecharoen, Suporn; Paw, Naw Ta Mlar; Jittamala, Podjanee; Nosten, François H; Ricci, Daniela; McGready, Rose

2016-01-01

Neurological examination, including visual fixation and tracking of a target, is routinely performed in the Shoklo Malaria Research Unit postnatal care units on the Thailand-Myanmar border. We aimed to evaluate a simple visual newborn test developed in Italy and performed by non-specialized personnel working in neonatal care units. An intensive training of local health staff in Thailand was conducted prior to performing assessments at 24, 48 and 72 hours of life in healthy, low-risk term singletons. The 48 and 72 hours results were then compared to values obtained to those from Italy. Parents and staff administering the test reported on acceptability. One hundred and seventy nine newborns, between June 2011 and October 2012, participated in the study. The test was rapidly completed if the infant remained in an optimal behavioral stage (7 ± 2 minutes) but the test duration increased significantly (12 ± 4 minutes, p < 0.001) if its behavior changed. Infants were able to fix a target and to discriminate a colored face at 24 hours of life. Horizontal tracking of a target was achieved by 96% (152/159) of the infants at 48 hours. Circular tracking, stripe discrimination and attention to distance significantly improved between each 24-hour test period. The test was easily performed by non-specialized local staff and well accepted by the parents. Healthy term singletons in this limited-resource setting have a visual response similar to that obtained to gestational age matched newborns in Italy. It is possible to use these results as a reference set of values for the visual assessment in Karen and Burmese infants in the first 72 hours of life. The utility of the 24 hours test should be pursued.

Experimental Data for Two Different Alternator Configurations in a Solar Brayton Power System

NASA Technical Reports Server (NTRS)

Mason, Lee S.; Shaltens, Richard K.; Espinosa, William D.

1997-01-01

A solar dynamic (SD) space power system has been under test at the NASA Lewis Research Center since 1994. The SD Ground Test Demonstration (GTD) system includes a solar concentrator, heat receiver with thermal energy storage, Brayton power conversion unit, and radiator installed in a thermal-vacuum chamber with a solar simulator. The Brayton unit has been operated with two different turboalternator compressor (TAC) assemblies, one which included a Rice Lundell alternator and another which incorporated a permanent magnet (PM) alternator. The Rice alternator was part of the mini-Brayton rotating unit, designed and built during the 1970's and refurbished for the GTD. The PM TAC was a development unit from the Joint US/Russian SD Flight Project. This paper highlights the operational differences (and similarities) between the Rice and PM TAC configurations including a comparative evaluation of startup characteristics and operating performance. The two alternator configurations were tested under similar thermal conditions, as an interchangeable component within the SD system. The electrical characteristics of the two units, however, dictated the use of significantly different power conditioning and control strategies. The electrical control architectures are described and compared. Test data are presented on TAC startup and system operating performance for both configurations.

A pressure-packer system for conducting rising head tests in water table wells

USGS Publications Warehouse

Levy, Benjamin S.; Pannell, Lawrence J.; Dadoly, John P.

1993-01-01

The pressure system developed for fully-saturated well screens has been modified for conducting rising head tests in water table wells installed in highly permeable aquifers. The pressure system consists of a compressed air source and 1 inch diameter PVC piping with a packer attached at the end. The pressure system was evaluated in a series of rising head tests conducted in a well at a Superfund site in New England. The well was tested with slugs and with the pressure system. Within each technique, estimates of hydraulic conductivity showed no difference. Comparison of hydraulic conductivity estimates between techniques (slug test vs. pressure test) showed differences due to stratigraphy. The interval tested using slug tests crossed two stratigraphic units; the pressure system tested only one of these units. We conclude that the pressure system may be used to characterize the vertical hydraulic conductivity distribution in a series of successive tests by changing the packer position and the screened interval tested.

[Isokinetic testing of the shoulder of handball players].

PubMed

Michael, J W-P; König, D P; Bertram, C; Hessling, U; Eysel, P

2005-09-01

Aim of the study was to evaluate an isokinetic profile testing handball players to describe muscular imbalance. 30 athletes (15 male and 15 female) were measured at the Cybex 6000 test-unit for concentric internal and external rotation. Both shoulders, throwing arm (dominant shoulder) and the opposite shoulder were tested by speeds at 60 degrees/s and 180 degrees/s. There were sex specific differences which are also found in other sports. But these contrary data are not useful to define effective training concepts for handball-players with shoulder problems. From our point of view isokinetic testing of the shoulder joint in handball players can not reach any sufficient result. From our point of view there is no reason for using isokinetic testing to evaluate shoulder problems.

Large Area Crop Inventory Experiment (LACIE). Second-generation sampling strategy evaluation report. [Kansas, North Dakota, and U.S.S.R.

NASA Technical Reports Server (NTRS)

Basu, J. P. (Principal Investigator); Dragich, S. M.; Mcguigan, D. P.

1978-01-01

The author has identified the following significant results. The stratification procedure in the new sampling strategy for LACIE included: (1) correlation test results indicating that an agrophysical stratum may be homogeneous with respect to agricultural density, but not with respect to wheat density; and (2) agrophysical unit homogeneity test results indicating that with respect to agricultural density many agrophysical units are not homogeneous, but removal of one or more refined strata from any such current agrophysical unit can make the strata homogeneous. The apportioning procedure results indicated that the current procedure is not performing well and that the apportioned estimates of refined strata wheat area are often unreliable.

Brayton heat exchange unit development program

NASA Technical Reports Server (NTRS)

Morse, C. J.; Richard, C. E.; Duncan, J. D.

1971-01-01

A Brayton Heat Exchanger Unit (BHXU), consisting of a recuperator, a heat sink heat exchanger and a gas ducting system, was designed, fabricated, and tested. The design was formulated to provide a high performance unit suitable for use in a long-life Brayton-cycle powerplant. A parametric analysis and design study was performed to establish the optimum component configurations to achieve low weight and size and high reliability, while meeting the requirements of high effectiveness and low pressure drop. Layout studies and detailed mechanical and structural design were performed to obtain a flight-type packaging arrangement. Evaluation testing was conducted from which it is estimated that near-design performance can be expected with the use of He-Xe as the working fluid.

75 FR 41871 - International Conference on Harmonisation; Draft Guidance on Q4B Evaluation and Recommendation of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-19

... Texts for Use in the International Conference on Harmonisation Regions; Annex 14 on Bacterial Endotoxins... ``Q4B Evaluation and Recommendation of Pharmacopoeial Texts for Use in the ICH Regions; Annex 14... Endotoxins Test General Chapter harmonized text from each of the three pharmacopoeias (United States...

Key Lessons for the Design and Integration of Virtual Environments in Secondary Science.

ERIC Educational Resources Information Center

Crosier, Joanna K.; Cobb, Sue; Wilson, John R.

2002-01-01

Discusses a three-year research project in which a virtual environment to teach radioactivity in secondary schools in the United Kingdom was developed and tested. Emphasizes the importance of involving teachers through the development process and confirms the importance of school-based evaluation studies in the development and evaluation of…

An Evaluation of a Biological Slide-Tutorial Program.

ERIC Educational Resources Information Center

Chan, Gordon L.

Described is an auto-tutorial slide program for zoology students. A self-paced system was devised for observing the subject matter covered in the twelve study units of a zoology course. The post-testing evaluation revealed that students with lower grade point averages achieved scores comparable with students of higher grade point averages.…

Evaluating Gifted Identification Practice: Aptitude Testing and Linguistically Diverse Learners

ERIC Educational Resources Information Center

Matthews, Michael S.; Kirsch, Lauri

2011-01-01

The authors examined individually administered IQ scores from an entire K-5 population (N = 432) of Limited English Proficient students referred for gifted program eligibility determination in a single large urban district in the southeastern United States. Of 8 IQ tests compared, only 1, the Stanford-Binet V, had scores appreciably lower than…

Testing a passive revegetation approach for restoring coastal plain depression wetlands

Treesearch

Diane De Steven; Rebecca R. Sharitz; Julian H. Singer; Christopher D. Barton

2006-01-01

Restoration of coastal plain depressions, a biologically significant and threatened wetland type of the southeastern United States, has received little systematic research. Within the context of an experimental project designed to evaluate several restoration approaches, we tested whether successful revegetation can be achieved by passive methods (recruitment from seed...

USDA-FS Termiticide report termiticide efficacy results for 2008

Treesearch

Terry Wagner; Joe Mulrooney; Thomas Shelton; Chris Peterson

2009-01-01

The United States Department of Agriculture Forest Service (USDA-FS) evaluates candidate termiticides for federal and state registration. In 2008, the USDA-FS administered 33 agreements with product manufacturers as part of its ongoing Termiticide Testing Program. Two termiticides were installed at the four national test sites in Florida (February), Arizona (April),...

Conditional Cash Transfers and School Dropout Rates

ERIC Educational Resources Information Center

Dearden, Lorraine; Emmerson, Carl; Frayne, Christine; Meghir, Costas

2009-01-01

This paper evaluates a United Kingdom pilot study designed to test whether a means-tested conditional cash transfer paid to 16- to 18-year-olds for staying in full-time education is an effective way of reducing the proportion of school dropouts. The transfer's impact is substantial: In the first year, full-time education participation rates…

77 FR 70724 - Eligibility of the Republic of Korea To Export Poultry Products to the United States

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-27

...) official controls over condemned product; (8) a Hazard Analysis and Critical Control Point (HACCP) system...) Hazard Analysis and Critical Control Point (HACCP) Systems, (5) Chemical Residue Testing Programs, and (6) Microbiological Testing Programs. FSIS evaluates the information submitted to verify that the critical points in...

Performance of Loblolly Pine Seed Sources in Argentina

Treesearch

Timothy La Farge; Floyd E. Bridgwater; Mirta N. Baez

1999-01-01

Four test series of loblolly pine (Pinus taeda L.) were evaluated to determine the performance in northeastern Argentina of seed sources from three breeding populations in the southeastern United States. Three half-sib progeny tests of seed sources from Florida and Louisiana demonstrated strong genetic gains for height, dbh, and volume growth....

Genetic and clinical evaluation of juvenile retinoschisis.

PubMed

Kim, Judy E; Ruttum, Mark S; Koeberl, Matthew J; Hassemer, Eryn L; Sidjanin, D J

2009-04-01

Juvenile retinoschisis is a rare retinal dystrophy caused by RS1 gene mutations.(1) Clinical examinations and molecular testing definitively diagnosed juvenile retinoschisis in 2 male infants, one of whom had a novel mutation not previously reported in the United States. Genetic testing may be the simplest way to confirm this diagnosis in infants.

Genetic and clinical evaluation of juvenile retinoschisis

PubMed Central

Kim, Judy E.; Ruttum, Mark S.; Koeberl, Matthew J.; Hassemer, Eryn L.; Sidjanin, D. J.

2014-01-01

Juvenile retinoschisis is a rare retinal dystrophy caused by RS1 gene mutations.1 Clinical examinations and molecular testing definitively diagnosed juvenile retinoschisis in 2 male infants, one of whom had a novel mutation not previously reported in the United States. Genetic testing may be the simplest way to confirm this diagnosis in infants. PMID:19393523

Evaluation of Serodiagnostic Assays for Mycobacterium bovis Infection in Elk, White-Tailed Deer, and Reindeer in the United States

PubMed Central

Nelson, Jeffrey T.; Orloski, Kathleen A.; Lloyd, Audra L.; Camacho, Mark; Schoenbaum, Mark A.; Robbe-Austerman, Suelee; Thomsen, Bruce V.; Hall, S. Mark

2012-01-01

In 2011, the United States Department of Agriculture conducted a project in which elk (Cervus elaphus spp.), white-tailed deer (WTD) (Odocoileus virginianus), and reindeer (Rangifer tarandus) were evaluated by the single cervical tuberculin test (SCT), comparative cervical tuberculin test (CCT), and serologic tests. The rapid antibody detection tests evaluated were the CervidTB Stat-Pak (Stat-Pak), and the Dual Path Platform VetTB (DPP). Blood was collected from presumably uninfected animals prior to tuberculin injection for the SCT. A total of 1,783 animals were enrolled in the project. Of these, 1,752 (98.3%) were classified as presumably uninfected, based on originating from a captive cervid herd with no history of exposure to TB. Stat-Pak specificity estimates were 92.4% in reindeer, 96.7% in WTD, and 98.3% in elk and were not significantly different from SCT specificity estimates. Using the DPP in series on Stat-Pak antibody-positive samples improved specificity in the three species. Thirty one animals were classified as confirmed infected, based on necropsy and laboratory results, and 27/31 were antibody positive on Stat-Pak for an estimated sensitivity of 87.1%. The study findings indicate that rapid serologic tests used in series are comparable to the SCT and CCT and may have a greater ability to detect TB-infected cervids. PMID:22792512

Evaluation of Test Methods for Triaxially Braided Composites using a Meso-Scale Finite Element Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Chao

The characterization of triaxially braided composite is complicate due to the nonuniformity of deformation within the unit cell as well as the possibility of the freeedge effect related to the large size of the unit cell. Extensive experimental investigation has been conducted to develop more accurate test approaches in characterizing the actual mechanical properties of the material we are studying. In this work, a meso-scale finite element model is utilized to simulate two complex specimens: notched tensile specimen and tube tensile specimen, which are designed to avoid the free-edge effect and free-edge effect induced premature edge damage. The full fieldmore » strain data is predicted numerically and compared with experimental data obtained by Digit Image Correlation. The numerically predicted tensile strength values are compared with experimentally measured results. The discrepancy between numerically predicted and experimentally measured data, the capability of different test approaches are analyzed and discussed. The presented numerical model could serve as assistance to the evaluation of different test methods, and is especially useful in identifying potential local damage events.« less

Department of the Navy Supporting Data for Fiscal Year 1983 Budget Estimates Descriptive Summaries Submitted to Congress February 1982. Research, Development, Test and Evaluation, Navy. Book 2 of 3. Tactical Programs.

DTIC Science & Technology

1982-02-01

control unit will detect and classify submerged submarins transiting within PJ The EnCAPsulated pedo augments air, surface and submarine anti...vidicon (date link video enhancement). Conduct Operational Test and Evaluation. Complete Large Scale Integration Receiver-Decoder improvement. Continue...analysis, and data link video enhancement focusing on application of a new silicon vidicon was continued; data link improvements such as adaptive null

Solid polymer electrolyte (SPE) fuel cell technology program, phase 2/2A. [testing and evaluations

NASA Technical Reports Server (NTRS)

1976-01-01

Test evaluations were performed on a fabricated single solid polymer electrolyte cell unit. The cell operated at increased current density and at higher performance levels. This improved performance was obtained through a combination of increased temperature, increased reactant pressures, improved activation techniques and improved thermal control over the baseline cell configuration. The cell demonstrated a higher acid content membrane which resulted in increased performance. Reduced catalyst loading and low cost membrane development showed encouraging results.

Design of the HPTN 065 (TLC-Plus) study: A study to evaluate the feasibility of an enhanced test, link-to-care, plus treat approach for HIV prevention in the United States

PubMed Central

Gamble, Theresa; Branson, Bernard; Donnell, Deborah; Hall, H Irene; King, Georgette; Cutler, Blayne; Hader, Shannon; Burns, David; Leider, Jason; Wood, Angela Fulwood; G. Volpp, Kevin; Buchacz, Kate; El-Sadr, Wafaa M

2017-01-01

Background/Aims HIV continues to be a major public health threat in the United States, and mathematical modeling has demonstrated that the universal effective use of antiretroviral therapy among all HIV-positive individuals (i.e. the “test and treat” approach) has the potential to control HIV. However, to accomplish this, all the steps that define the HIV care continuum must be achieved at high levels, including HIV testing and diagnosis, linkage to and retention in clinical care, antiretroviral medication initiation, and adherence to achieve and maintain viral suppression. The HPTN 065 (Test, Link-to-Care Plus Treat [TLC-Plus]) study was designed to determine the feasibility of the “test and treat” approach in the United States. Methods HPTN 065 was conducted in two intervention communities, Bronx, NY, and Washington, DC, along with four non-intervention communities, Chicago, IL; Houston, TX; Miami, FL; and Philadelphia, PA. The study consisted of five components: (1) exploring the feasibility of expanded HIV testing via social mobilization and the universal offer of testing in hospital settings, (2) evaluating the effectiveness of financial incentives to increase linkage to care, (3) evaluating the effectiveness of financial incentives to increase viral suppression, (4) evaluating the effectiveness of a computer-delivered intervention to decrease risk behavior in HIV-positive patients in healthcare settings, and (5) administering provider and patient surveys to assess knowledge and attitudes regarding the use of antiretroviral therapy for prevention and the use of financial incentives to improve health outcomes. The study used observational cohorts, cluster and individual randomization, and made novel use of the existing national HIV surveillance data infrastructure. All components were developed with input from a community advisory board, and pragmatic methods were used to implement and assess the outcomes for each study component. Results A total of 76 sites in Washington, DC, and the Bronx, NY, participated in the study: 37 HIV test sites, including 16 hospitals, and 39 HIV care sites. Between September 2010 and December 2014, all study components were successfully implemented at these sites and resulted in valid outcomes. Our pragmatic approach to the study design, implementation, and the assessment of study outcomes allowed the study to be conducted within established programmatic structures and processes. In addition, it was successfully layered on the ongoing standard of care and existing data infrastructure without disrupting health services. Conclusion The HPTN 065 study demonstrated the feasibility of implementing and evaluating a multi-component “test and treat” trial that included a large number of community sites and involved pragmatic approaches to study implementation and evaluation. PMID:28627929

Design of the HPTN 065 (TLC-Plus) study: A study to evaluate the feasibility of an enhanced test, link-to-care, plus treat approach for HIV prevention in the United States.

PubMed

Gamble, Theresa; Branson, Bernard; Donnell, Deborah; Hall, H Irene; King, Georgette; Cutler, Blayne; Hader, Shannon; Burns, David; Leider, Jason; Wood, Angela Fulwood; G Volpp, Kevin; Buchacz, Kate; El-Sadr, Wafaa M

2017-08-01

Background/Aims HIV continues to be a major public health threat in the United States, and mathematical modeling has demonstrated that the universal effective use of antiretroviral therapy among all HIV-positive individuals (i.e. the "test and treat" approach) has the potential to control HIV. However, to accomplish this, all the steps that define the HIV care continuum must be achieved at high levels, including HIV testing and diagnosis, linkage to and retention in clinical care, antiretroviral medication initiation, and adherence to achieve and maintain viral suppression. The HPTN 065 (Test, Link-to-Care Plus Treat [TLC-Plus]) study was designed to determine the feasibility of the "test and treat" approach in the United States. Methods HPTN 065 was conducted in two intervention communities, Bronx, NY, and Washington, DC, along with four non-intervention communities, Chicago, IL; Houston, TX; Miami, FL; and Philadelphia, PA. The study consisted of five components: (1) exploring the feasibility of expanded HIV testing via social mobilization and the universal offer of testing in hospital settings, (2) evaluating the effectiveness of financial incentives to increase linkage to care, (3) evaluating the effectiveness of financial incentives to increase viral suppression, (4) evaluating the effectiveness of a computer-delivered intervention to decrease risk behavior in HIV-positive patients in healthcare settings, and (5) administering provider and patient surveys to assess knowledge and attitudes regarding the use of antiretroviral therapy for prevention and the use of financial incentives to improve health outcomes. The study used observational cohorts, cluster and individual randomization, and made novel use of the existing national HIV surveillance data infrastructure. All components were developed with input from a community advisory board, and pragmatic methods were used to implement and assess the outcomes for each study component. Results A total of 76 sites in Washington, DC, and the Bronx, NY, participated in the study: 37 HIV test sites, including 16 hospitals, and 39 HIV care sites. Between September 2010 and December 2014, all study components were successfully implemented at these sites and resulted in valid outcomes. Our pragmatic approach to the study design, implementation, and the assessment of study outcomes allowed the study to be conducted within established programmatic structures and processes. In addition, it was successfully layered on the ongoing standard of care and existing data infrastructure without disrupting health services. Conclusion The HPTN 065 study demonstrated the feasibility of implementing and evaluating a multi-component "test and treat" trial that included a large number of community sites and involved pragmatic approaches to study implementation and evaluation.

Preliminary test results from the CELSS Test Facility Engineering Development Unit

NASA Technical Reports Server (NTRS)

Kliss, Mark H.; Macelroy, R. D.; Blackwell, C. C.; Borchers, B. A.; Drews, M. E.; Longabaugh, J. R.; Yendler, B. S.; Zografos, A. I.

1994-01-01

As part of the NASA Controlled Ecological Life Support System (CELSS) Program, a CELSS Test Facility (CTF) is being planned for installation on the Space Station. The CTF will be used to provide data on the productivity and efficiency of a variety of CELSS higher plant crops grown in the microgravity environment of the Space Station. Tight environmental control will be maintained while data on gas exchange rates and biomass accumulation rates are collected. In order to obtain an early realistic determination of the subsystem and system requirements necessary to provide the environmental conditions specified for CTF crop productivity experiments, an Engineering Development Unit (EDU) has been designed, constructed and is in the process of subsystem and system testing at NASA Ames Research Center. The EDU is a ground test-bed which will be used to characterize the integrated performance of major subsystem technologies, to evaluate hardware candidates and control strategies required for the CTF, and to further define the ability to meet CTF requirements within present Space Station constraints. This paper reviews the functional requirements for the EDU, and focuses on the performance evaluation and test results of the various subsystems. Preliminary integrated performance results and control system operation are addressed, and plans for future science and technology testing are discussed.

Selection of Environmentally Friendly Solvents for the Extravehicular Mobility Unit Secondary Oxygen Pack Cold Trap Testing

NASA Technical Reports Server (NTRS)

Steele, John; Chullen, Cinda; Morenz, Jesse; Stephenson, Curtis

2010-01-01

Freon-113(TradeMark) has been used as a chemistry lab sampling solvent at NASA/JSC for EMU (extravehicular Mobility Unit) SOP (Secondary Oxygen Pack) oxygen testing Cold Traps utilized at the USA (United Space Alliance) Houston facility. Similar testing has occurred at the HSWL (Hamilton Sundstrand Windsor Locks) facility. A NASA Executive Order bans the procurement of all ODS (ozone depleting substances), including Freon-113 by the end of 2009. In order to comply with NASA direction, HSWL began evaluating viable solvents to replace Freon-113 . The study and testing effort to find Freon-113 replacements used for Cold Trap sampling is the subject of this paper. Test results have shown HFE-7100 (a 3M fluorinated ether) to be an adequate replacement for Freon-113 as a solvent to remove and measure the non-volatile residue collected in a Cold Trap during oxygen testing. Furthermore, S-316 (a Horiba Instruments Inc. high molecular weight, non-ODS chlorofluorocarbon) was found to be an adequate replacement for Freon-113 as a solvent to reconstitute non-volatile residue removed from a Cold Trap during oxygen testing for subsequent HC (hydrocarbon) analysis via FTIR (Fourier Transform Infrared Spectroscopy).

Biometric identification standards research

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Air Quality Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM projects being...

Effects of unit empowerment and perceived support for professional nursing practice on unit effectiveness and individual nurse well-being: a time-lagged study.

PubMed

Spence Laschinger, Heather K; Nosko, Amanda; Wilk, Piotr; Finegan, Joan

2014-12-01

Recruitment and retention strategies have emphasized the importance of positive work environments that support professional nursing practice for sustaining the nursing workforce. Unit leadership that creates empowering workplace conditions plays a key role in establishing supportive practice environments that increase work effectiveness, and, ultimately, improves job satisfaction. To test a multi-level model examining the effect of both contextual and individual factors on individual nurse job satisfaction. At the unit level, structural empowerment and support for professional nursing practice (organizational resources) were hypothesized to be predictors of unit level effectiveness. At the individual level, core self-evaluation, and psychological empowerment (intrapersonal resources) were modeled as predictors of nurse job satisfaction one year later. Cross-level unit effects on individual nurses' job satisfaction were also examined. This study employed a longitudinal survey design with 545 staff nurses from 49 hospital units in Ontario, Canada. Participants completed a survey at two points in time (response rate of 40%) with standardized measures of the major study variables in the hypothesized model. Multilevel structural equation modeling was used to test the model. Nurses shared perceptions of structural empowerment on their units indirectly influenced their shared perceptions of unit effectiveness (Level 2) through perceived unit support for professional nursing practice, which in turn, had a significant positive direct effect on unit effectiveness (Level 2). Unit effectiveness was also strongly related to individual nurse job satisfaction one year later. At Level 1, higher core self-evaluation had a direct and indirect effect on job satisfaction through increased psychological empowerment. The results suggest that nurses' job satisfaction is influenced by a combination of individual and contextual factors demonstrating utility in considering both sources of nurses' satisfaction with their work in creating effective nursing work environments. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fit Analysis of Different Framework Fabrication Techniques for Implant-Supported Partial Prostheses.

PubMed

Spazzin, Aloísio Oro; Bacchi, Atais; Trevisani, Alexandre; Farina, Ana Paula; Dos Santos, Mateus Bertolini

2016-01-01

This study evaluated the vertical misfit of implant-supported frameworks made using different techniques to obtain passive fit. Thirty three-unit fixed partial dentures were fabricated in cobalt-chromium alloy (n = 10) using three fabrication methods: one-piece casting, framework cemented on prepared abutments, and laser welding. The vertical misfit between the frameworks and the abutments was evaluated with an optical microscope using the single-screw test. Data were analyzed using one-way analysis of variance and Tukey test (α = .05). The one-piece casted frameworks presented significantly higher vertical misfit values than those found for framework cemented on prepared abutments and laser welding techniques (P < .001 and P < .003, respectively). Laser welding and framework cemented on prepared abutments are effective techniques to improve the adaptation of three-unit implant-supported prostheses. These techniques presented similar fit.

ICSBEP Benchmarks For Nuclear Data Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Briggs, J. Blair

2005-05-24

The International Criticality Safety Benchmark Evaluation Project (ICSBEP) was initiated in 1992 by the United States Department of Energy. The ICSBEP became an official activity of the Organization for Economic Cooperation and Development (OECD) -- Nuclear Energy Agency (NEA) in 1995. Representatives from the United States, United Kingdom, France, Japan, the Russian Federation, Hungary, Republic of Korea, Slovenia, Serbia and Montenegro (formerly Yugoslavia), Kazakhstan, Spain, Israel, Brazil, Poland, and the Czech Republic are now participating. South Africa, India, China, and Germany are considering participation. The purpose of the ICSBEP is to identify, evaluate, verify, and formally document a comprehensive andmore » internationally peer-reviewed set of criticality safety benchmark data. The work of the ICSBEP is published as an OECD handbook entitled ''International Handbook of Evaluated Criticality Safety Benchmark Experiments.'' The 2004 Edition of the Handbook contains benchmark specifications for 3331 critical or subcritical configurations that are intended for use in validation efforts and for testing basic nuclear data. New to the 2004 Edition of the Handbook is a draft criticality alarm / shielding type benchmark that should be finalized in 2005 along with two other similar benchmarks. The Handbook is being used extensively for nuclear data testing and is expected to be a valuable resource for code and data validation and improvement efforts for decades to come. Specific benchmarks that are useful for testing structural materials such as iron, chromium, nickel, and manganese; beryllium; lead; thorium; and 238U are highlighted.« less

Aetiology of obstructive azoospermia in Chinese infertility patients.

PubMed

Han, H; Liu, S; Zhou, X-G; Tian, L; Zhang, X-D

2016-09-01

To explore the aetiology of obstructive azoospermia (OA) in Chinese infertility patients, 133 OA patients was included in this study diagnosed and evaluated by one major specialist trained urological infertility. We retrospected the medical records to collect relative information. All of the patients had been underwent physical examination, ultrasound scan to the urogenital system, serum hormone tests, genetic tests and two separate semen analyses. The mean age of all 133 patients was 32.7 ± 6.8 years. A total of 266 reproductive tract units (two/patient) were classified into four categories: no causes (Idiopathic) for 74 units (27.8%), single cause for 173 units (65.0%), double causes for 17 units (6.4%) and triple causes for two units (0.8%). As to single cause of OA, there were four types: trauma for 0 unit (0%), infection for 125 units (47.0%), dysplasia for 11 units (4.1%) and surgeries for 37 units (13.9%). As to total cause of OA, there were five types: infection for 144 units (54.1%), orchitis for 51 units (19.2%), epididymitis for 54 units (20.3%), gonorrhoea for 28 units (10.5%) and inguinal hernia repair surgery for 18 units (6.8%). The most frequent cause of obstructive azoospermia was infection revealed in these Chinese infertility populations, followed by idiopathic reason. © 2015 Blackwell Verlag GmbH.

Contaminants in stream sediments from seven United States metropolitan areas: part II—sediment toxicity to the amphipod Hyalella azteca and the midge Chironomus dilutus

USGS Publications Warehouse

Kemble, Nile E.; Hardesty, Douglas K.; Ingersoll, Christopher G.; Kunz, James L.; Sibley, Paul K.; Calhoun, Daniel L.; Gilliom, Robert J.; Kuivila, Kathryn; Nowell, Lisa H.; Moran, Patrick W.

2013-01-01

Pyrethroids are hydrophobic compounds that have been observed to accumulate in sediments (Laskowski 2002). Toxicity of pyrethroids in field-collected sediment from small urban streams (Weston et al. 2005; Holmes et al. 2008; Ding et al. 2010; Domagalski et al. 2010) or with pyrethroids spiked into sediment (Amweg et al. 2006; Hintzen et al. 2009) have been evaluated primarily in 10 day lethality tests conducted with the amphipod Hyalella azteca. However, the sublethal effects in long-term exposures to pyrethroids in sediment have not been evaluated, and the distribution of pyrethroids sediments has not typically been evaluated in wadeable streams (Gilliom et al. 2006). This article is the second in a series that describe the results of a study of the distribution and toxicity of pyrethroids and other co-occurring trace elements and organic contaminants (PCBs, PAHs, OC pesticides) in stream sediments from 7 metropolitan areas across the United States (Moran et al. 2012). The study evaluated 98 sediment samples collected from streams ranging from undeveloped to highly urban and differs from previous studies by sampling larger wadeable streams and avoiding point sources (such as storm drains) and other inflows (Gilliom et al. 2006). Part 1 of the series characterizes sediment contaminants in relation to urbanization and other factors in the 7 metropolitan study areas (Nowell et al. 2012). Part 2 (this article) evaluates relationships between sediment chemistry and sediment toxicity in 28 day whole-sediment exposures conducted with the amphipod H. azteca and in 10 day whole-sediment exposure conducted with the midge Chironomus dilutus (USEPA United States Environmental Protection Agency 2000; ASTM American Society for Testing and Materials International 2012). Toxicity end points evaluated in the amphipod and midge exposures included the effects of these field-collected sediments on survival, weight, or biomass of the test organisms.

Total Organisms Per Liter of Air with Particle Size Distribution (TOLAp): New Unit of Measure for the Test and Evaluation of Biodetectors

DTIC Science & Technology

2010-09-01

captured by the unit of measure. A bioaerosol with particles the size of peas poses a relatively low threat because the particles will settle to the...background particles. Something as simple as green fluorescent protein (GFP) could act as a signal to a fluorescently gated particle sizer, indicating that a

Evaluation of the Productive Skills in the Second Language: The Work of the Assessment of Performance Unit (APU).

ERIC Educational Resources Information Center

Dickson, Peter

The work in second language education of the Assessment of Performance Unit, established by the Department of Education and Science of England and Wales to monitor certain areas of the public education curriculum is described. The focus is on the development of a rationale for testing, the elicitation procedures used in the assessment of speaking…

Variation in loblolly pine ring microfibril angle in the southeastern United States

Treesearch

Lewis Jordan; Rechun He; Daniel B. Hall; Alexander III Clark; Richard F. Daniels

2007-01-01

The effect of physiographic region on microfibril angle (MFA) in loblolly pine (Pinus taeda L.) in the southern United States was evaluated. MFA was determined at 1.4, 4.6, 7.6, 10.7, and 13.7 m up the stem of 59 trees, representing five physiographic regions. A nonlinear mixed-effects model was developed to test for regional differences in the...

Preparing staff for intentional rounding: a process yielding success on a general surgical unit.

PubMed

Patterson, Lisa M

2014-01-01

Intentional rounding is a strategicway to improve patient care through decreasing falls and hospital-acquired pressure ulcers, while increasing patient satisfaction. On the basis of literature reviews and discussions with nurses on units that pilot-tested intentional rounding, useful strategies emerged. This article will provide information about intentional rounding, a means for planning implementation, and the results of evaluating its implementation.

Emergency Warning Systems. Part 2. Warning Systems - Evaluation Guidelines.

DTIC Science & Technology

1983-07-01

ELEMENT. PROJECT. TASK AREA A WORK UNIT NUMBERS PRC Voorhees Work Unit 2234G 1500 Planning Research Drive McLean, Virginia 22102 ___ 11. CONTROLLING ...different from Controlling Office) IS. SECURITY CLASS. (of this report) Unclassified 15a. DECLASSIFICATION/DOWNGRADING SCHEDULE 16. DISTRIBUTION...systems that control these warning systems are discussed. Test results of several warning systems are included along with a discussion of sound

Corrective Action Investigation Plan for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada National Security Site, Nevada with ROTCs 1, 2, and 3 (Revision 0, September 2000)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrews, Robert; Marutzky, Sam

2000-09-01

This Corrective Action Investigation Plan contains the U.S. Department of Energy, Nevada Operations Office's (DOE/NV's) approach to collect the data necessary to evaluate Corrective Action Alternatives (CAAs) appropriate for the closure of Corrective Action Unit (CAU) 97 under the Federal Facility Agreement and Consent Order (FFACO). Corrective Action Unit 97, collectively known as the Yucca Flat/Climax Mine CAU, consists of 720 Corrective Action Sites (CASs). The Yucca Flat/Climax Mine CAU extends over several areas of the NTS and constitutes one of several areas used for underground nuclear testing in the past. The nuclear tests resulted in groundwater contamination in themore » vicinity as well as downgradient of the underground test areas. Based on site history, the Yucca Flat underground nuclear tests were conducted in alluvial, volcanic, and carbonate rocks; whereas, the Climax Mine tests were conducted in an igneous intrusion located in northern Yucca Flat. Particle-tracking simulations performed during the regional evaluation indicate that the local Climax Mine groundwater flow system merges into the much larger Yucca Flat groundwater flow systems during the 1,000-year time period of interest. Addressing these two areas jointly and simultaneously investigating them as a combined CAU has been determined the best way to proceed with corrective action investigation (CAI) activities. The purpose and scope of the CAI includes characterization activities and model development conducted in five major sequential steps designed to be consistent with FFACO Underground Test Area Project's strategy to predict the location of the contaminant boundary, develop and implement a corrective action, and close each CAU. The results of this field investigation will support a defensible evaluation of CAAs in the subsequent corrective action decision document.« less

Nickel and cobalt release from children's toys purchased in Denmark and the United States.

PubMed

Jensen, Peter; Hamann, Dathan; Hamann, Carsten R; Jellesen, Morten S; Jacob, Sharon E; Thyssen, Jacob P

2014-01-01

Nickel is the most common allergen detected by patch testing in children. There is an increasing number of cases in children who have not had exposure to piercing. Although the clinical relevance of nickel patch test reactions in children is sometimes uncertain, continued vigilance to identify new sources of nickel exposure in this age group is important. Recent case reports have described allergic nickel contact dermatitis in children following exposure to toys, but the magnitude of this problem is unknown. The aim of this study was to evaluate nickel and cobalt release from children's toys. We purchased 212 toys in 18 different retail and online stores in the United States and Denmark. Nickel and cobalt release was tested using the dimethylglyoxime and cobalt screening spot tests. A total of 73 toys (34.4%) released nickel, and none released cobalt. Toys are a commonly overlooked source of nickel exposure and sensitization. Therefore, dermatologists, allergists, and pediatricians should consider the role of toys in their evaluation of children with dermatitis, and the parents of children with positive nickel patch test reactions should be told that toys may release nickel and be a potential chemical source in the manifestation of allergic contact dermatitis.

Progress in Quantitative Viral Load Testing: Variability and Impact of the WHO Quantitative International Standards

PubMed Central

Sun, Y.; Tang, L.; Procop, G. W.; Hillyard, D. R.; Young, S. A.; Caliendo, A. M.

2016-01-01

ABSTRACT It has been hoped that the recent availability of WHO quantitative standards would improve interlaboratory agreement for viral load testing; however, insufficient data are available to evaluate whether this has been the case. Results from 554 laboratories participating in proficiency testing surveys for quantitative PCR assays of cytomegalovirus (CMV), Epstein-Barr virus (EBV), BK virus (BKV), adenovirus (ADV), and human herpesvirus 6 (HHV6) were evaluated to determine overall result variability and then were stratified by assay manufacturer. The impact of calibration to international units/ml (CMV and EBV) on variability was also determined. Viral loads showed a high degree of interlaboratory variability for all tested viruses, with interquartile ranges as high as 1.46 log10 copies/ml and the overall range for a given sample up to 5.66 log10 copies/ml. Some improvement in result variability was seen when international units were adopted. This was particularly the case for EBV viral load results. Variability in viral load results remains a challenge across all viruses tested here; introduction of international quantitative standards may help reduce variability and does so more or less markedly for certain viruses. PMID:27852673

Outbreaks in Health Care Settings.

PubMed

Sood, Geeta; Perl, Trish M

2016-09-01

Outbreaks and pseudo-outbreaks in health care settings can be complex and should be evaluated systematically using epidemiologic tools. Laboratory testing is an important part of an outbreak evaluation. Health care personnel, equipment, supplies, water, ventilation systems, and the hospital environment have been associated with health care outbreaks. Settings including the neonatal intensive care unit, endoscopy, oncology, and transplant units are areas that have specific issues which impact the approach to outbreak investigation and control. Certain organisms have a predilection for health care settings because of the illnesses of patients, the procedures performed, and the care provided. Copyright © 2016 Elsevier Inc. All rights reserved.

Design and flight test of a differential GPS/inertial navigation system for approach/landing guidance

NASA Technical Reports Server (NTRS)

Vallot, Lawrence; Snyder, Scott; Schipper, Brian; Parker, Nigel; Spitzer, Cary

1991-01-01

NASA-Langley has conducted a flight test program evaluating a differential GPS/inertial navigation system's (DGPS/INS) utility as an approach/landing aid. The DGPS/INS airborne and ground components are based on off-the-shelf transport aircraft avionics, namely a global positioning/inertial reference unit (GPIRU) and two GPS sensor units (GPSSUs). Systematic GPS errors are measured by the ground GPSSU and transmitted to the aircraft GPIRU, allowing the errors to be eliminated or greatly reduced in the airborne equipment. Over 120 landings were flown; 36 of these were fully automatic DGPS/INS landings.

Higher cost of implementing Xpert(®) MTB/RIF in Ugandan peripheral settings: implications for cost-effectiveness.

PubMed

Hsiang, E; Little, K M; Haguma, P; Hanrahan, C F; Katamba, A; Cattamanchi, A; Davis, J L; Vassall, A; Dowdy, D

2016-09-01

Initial cost-effectiveness evaluations of Xpert(®) MTB/RIF for tuberculosis (TB) diagnosis have not fully accounted for the realities of implementation in peripheral settings. To evaluate costs and diagnostic outcomes of Xpert testing implemented at various health care levels in Uganda. We collected empirical cost data from five health centers utilizing Xpert for TB diagnosis, using an ingredients approach. We reviewed laboratory and patient records to assess outcomes at these sites and10 sites without Xpert. We also estimated incremental cost-effectiveness of Xpert testing; our primary outcome was the incremental cost of Xpert testing per newly detected TB case. The mean unit cost of an Xpert test was US$21 based on a mean monthly volume of 54 tests per site, although unit cost varied widely (US$16-58) and was primarily determined by testing volume. Total diagnostic costs were 2.4-fold higher in Xpert clinics than in non-Xpert clinics; however, Xpert only increased diagnoses by 12%. The diagnostic costs of Xpert averaged US$119 per newly detected TB case, but were as high as US$885 at the center with the lowest volume of tests. Xpert testing can detect TB cases at reasonable cost, but may double diagnostic budgets for relatively small gains, with cost-effectiveness deteriorating with lower testing volumes.

Qualification of Daiichi Units 1, 2, and 3 Data for Severe Accident Evaluations - Process and Illustrative Examples from Prior TMI-2 Evaluations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rempe, Joy Lynn; Knudson, Darrell Lee

2014-09-01

The accidents at the Three Mile Island Unit 2 (TMI-2) Pressurized Water Reactor (PWR) and the Daiichi Units 1, 2, and 3 Boiling Water Reactors (BWRs) provide unique opportunities to evaluate instrumentation exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during the TMI-2 accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated in 2012 by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2more » sensor survivability and data qualification efforts. This initial review focused on the set of sensors deemed most important by post-TMI-2 instrumentation evaluation programs. Instrumentation evaluation programs focused on data required by TMI-2 operators to assess the condition of the reactor and containment and the effect of mitigating actions taken by these operators. In addition, prior efforts focused on sensors providing data required for subsequent forensic evaluations and accident simulations. To encourage the potential for similar activities to be completed for qualifying data from Daiichi Units 1, 2, and 3, this report provides additional details related to the formal process used to develop a qualified TMI-2 data base and presents data qualification details for three parameters: primary system pressure; containment building temperature; and containment pressure. As described within this report, sensor evaluations and data qualification required implementation of various processes, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design to instruments easily removed from the TMI-2 plant for evaluations. As documented in this report, results from qualifying data for these parameters led to key insights related to TMI-2 accident progression. Hence, these selected examples illustrate the types of activities completed in the TMI-2 data qualification process and the importance of such a qualification effort. These details are documented in this report to facilitate implementation of similar process using data and examinations at the Daiichi Units 1, 2, and 3 reactors so that BWR-specific benefits can be obtained.« less

Performance evaluation of a second-generation elastic loop mobility system

NASA Technical Reports Server (NTRS)

Melzer, K. J.; Swanson, G. D.

1974-01-01

Tests were conducted to evaluate the mobility performance of a second-generation Elastic Loop Mobility System (ELMS II). Performance on level test lanes and slopes of lunar soil simulant (LSS) and obstacle-surmounting and crevasse-crossing capabilities were investigated. In addition, internal losses and contact pressure distributions were evaluated. To evaluate the soft-soil performance, two basic soil conditions were tested: loose (LSS1) and dense (LSS5). These conditions embrace the spectrum of soil strengths tested during recent studies for NASA related to the mobility performance of the LRV. Data indicated that for the tested range of the various performance parameters, performance was independent of unit load (contact pressure) and ELMS II drum angular velocity, but was influenced by soil strength and ELMS pitch mode. Power requirements were smaller at a given system output for dense soil than for loose soil. The total system output in terms of pull developed or slope-climbing capability was larger for the ELMS II operating in restrained-pitch mode than in free-pitch mode.

In vitro and in vivo Safety Evaluation of NephureTM

PubMed Central

Cowley, Helena; Yan, Qin; Koetzner, Lee; Dolan, Laurie; Nordwald, Erik; Cowley, Aaron B.

2017-01-01

NephureTM is a proprietary oxalate decarboxylase (OxDC) enzyme being developed as a food ingredient. In this study, the safety of NephureTM was evaluated in a bacterial mutagenicity assay and in a sub-chronic (13-week) oral toxicity study in rats. NephureTM did not show any mutagenic properties in the mutagenicity assay. In the 13-week sub-chronic oral toxicity study in which 10 Sprague Dawley rats per sex were administered 0, 118, 235 and 475 mg/kg bw/day (8260, 16450 and 33,250 Units/kg bw/day, respectively) of NephureTM by gavage, male and female rats did not show any test article-related clinical observations or effects on body weight, body weight gain, food consumption, food efficiency, ophthalmology, functional observational battery parameters or motor activity. Furthermore, there were no changes in coagulation, clinical chemistry, urinalysis or hematology parameters, macroscopic/microscopic findings or organ weights that could be attributed to the test article. Based on these results, NephureTM was not mutagenic and the no-adverse-effect level (NOAEL) in the 13-week study was determined to be 475 mg/kg bw/day (33,250 Units/kg bw/day). Evaluation of the estimated consumption of NephureTM, generation of the metabolite formate, and the current safety studies resulted in a conclusion of a tolerable upper limit of 3450 Units of OxDC activity/day (57.5 Units activity/kg bw/day), when NephureTM is added to food to decrease dietary oxalate. PMID:28322893

Hockey-stick steam generator for LMFBR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hallinan, G.J.; Svedlund, P.E.

1981-01-01

This paper presents the criteria and evaluation leading to the selection of the Hockey Stick Steam Generator Concept and subsequent development of that concept for LMFBR application. The selection process and development of the Modular Steam Generator (MSG) is discussed, including the extensive test programs that culminated in the manufacture and test of a 35 MW(t) Steam Generator. The design of the CRBRP Steam Generator is described, emphasizing the current status and a review of the critical structural areas. CRBRP steam generator development tests are evaluated, with a discussion of test objectives and rating of the usefulness of test resultsmore » to the CRBRP prototype design. Manufacturing experience and status of the CRBRP prototype and plant units is covered. The scaleup of the Hockey Stick concept to large commercial plant application is presented, with an evaluation of scaleup limitations, transient effects, and system design implications.« less

Symbol signing design for older drivers

DOT National Transportation Integrated Search

2012-09-01

This report presents the Surveys, Interviews, and Workshops Test Plan for the national evaluation of the Los Angeles (LA) Congestion Reduction Demonstration (Metro ExpressLanes) under the United States Department of Transportation (U.S. DOT) Congesti...

75 FR 9627 - Notice of Issuance of Regulatory Guide

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-03

... staff uses in evaluating specific problems or postulated accidents, and data that the staff needs in its... qualification testing of a prototype unit under the most adverse design conditions. II. Further Information In...

Evaluation of a Combined Cyclone and Gas Filtration System for Particulate Removal in the Gasification Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rizzo, Jeffrey J.

2010-04-30

The Wabash gasification facility, owned and operated by sgSolutions LLC, is one of the largest single train solid fuel gasification facilities in the world capable of transforming 2,000 tons per day of petroleum coke or 2,600 tons per day of bituminous coal into synthetic gas for electrical power generation. The Wabash plant utilizes Phillips66 proprietary E-Gas (TM) Gasification Process to convert solid fuels such as petroleum coke or coal into synthetic gas that is fed to a combined cycle combustion turbine power generation facility. During plant startup in 1995, reliability issues were realized in the gas filtration portion of themore » gasification process. To address these issues, a slipstream test unit was constructed at the Wabash facility to test various filter designs, materials and process conditions for potential reliability improvement. The char filtration slipstream unit provided a way of testing new materials, maintenance procedures, and process changes without the risk of stopping commercial production in the facility. It also greatly reduced maintenance expenditures associated with full scale testing in the commercial plant. This char filtration slipstream unit was installed with assistance from the United States Department of Energy (built under DOE Contract No. DE-FC26-97FT34158) and began initial testing in November of 1997. It has proven to be extremely beneficial in the advancement of the E-Gas (TM) char removal technology by accurately predicting filter behavior and potential failure mechanisms that would occur in the commercial process. After completing four (4) years of testing various filter types and configurations on numerous gasification feed stocks, a decision was made to investigate the economic and reliability effects of using a particulate removal gas cyclone upstream of the current gas filtration unit. A paper study had indicated that there was a real potential to lower both installed capital and operating costs by implementing a char cyclonefiltration hybrid unit in the E-Gas (TM) gasification process. These reductions would help to keep the E-Gas (TM) technology competitive among other coal-fired power generation technologies. The Wabash combined cyclone and gas filtration slipstream test program was developed to provide design information, equipment specification and process control parameters of a hybrid cyclone and candle filter particulate removal system in the E-Gas (TM) gasification process that would provide the optimum performance and reliability for future commercial use. The test program objectives were as follows: 1. Evaluate the use of various cyclone materials of construction; 2. Establish the optimal cyclone efficiency that provides stable long term gas filter operation; 3. Determine the particle size distribution of the char separated by both the cyclone and candle filters. This will provide insight into cyclone efficiency and potential future plant design; 4. Determine the optimum filter media size requirements for the cyclone-filtration hybrid unit; 5. Determine the appropriate char transfer rates for both the cyclone and filtration portions of the hybrid unit; 6. Develop operating procedures for the cyclone-filtration hybrid unit; and, 7. Compare the installed capital cost of a scaled-up commercial cyclone-filtration hybrid unit to the current gas filtration design without a cyclone unit, such as currently exists at the Wabash facility.« less

A subjective evaluation of synthesized STOL airplane noises

NASA Technical Reports Server (NTRS)

Powell, C. A., Jr.

1973-01-01

A magnitude-estimation experiment was conducted to evaluate the subjective annoyance of the noise generated by possible future turbofan STOL aircraft as compared to that of several current CTOL aircraft. In addition, some of the units used to scale the magnitude of aircraft noise were evaluated with respect to their applicability to STOL noise. Twenty test subjects rated their annoyance to a total of 119 noises over a range of 75 PNdb to 105 PNdb. Their subjective ratings were compared with acoustical analysis of the noises in terms of 28 rating scale units. The synthesized STOL noises of this experiment were found to be slightly more annoying than the conventional CTOL noises at equal levels of PNL and EPNL. Over the range of levels investigated the scaling units, with a few exceptions, were capable of predicting the points of equal annoyance for all of the noises with plus or minus 3 dB. The inclusion of duration corrections, in general, improved the predictive capabilities of the various scaling units; however, tone corrections reduced their predictive capabilities.

Organizational Member Involvement in Physical Activity Coalitions across the United States: Development and Testing of a Novel Survey Instrument for Assessing Coalition Functioning

ERIC Educational Resources Information Center

Bornstein, Daniel B.; Pate, Russell R.; Beets, Michael W.; Saunders, Ruth P.; Blair, Steven N.

2015-01-01

Introduction: Coalitions are often composed of member organizations. Member involvement is thought to be associated with coalition success. No instrument currently exists for evaluating organizational member involvement in physical activity coalitions. This study aimed to develop a survey instrument for evaluating organizational member involvement…

Evaluation of insecticides for protecting southwestern ponderosa pines from attack by engraver beetles (Coleoptera: Curculionidae: Scolytinae)

Treesearch

Tom E. DeGomez; Christopher J. Hayes; John A. Anhold; Joel D. McMillin; Karen M. Clancy; Paul P. Bosu

2006-01-01

Insecticides that might protect pine trees from attack by engraver beetles (Ips spp.) have not been rigorously tested in the southwestern United States. We conducted two field experiments to evaluate the efficacy of several currently and potentially labeled preventative insecticides for protecting high-value ponderosa pine, Pinus ponderosa...

Evaluation of non-native Tsuga species as replacements for T. canadensis killed by hemlock woolly adelgid

Treesearch

Paul A. Weston; Richard W. Harper

2007-01-01

Several species of Tsuga from the western United States and Asia are under evaluation as potential replacements for T. canadensis being destroyed by hemlock woolly adelgid (Adelges tsugae Annand). Test plots were established in Katonah, NY in October, 2003, and trees were inoculated with adelgid egg masses in...

Squared Euclidean distance: a statistical test to evaluate plant community change

Treesearch

Raymond D. Ratliff; Sylvia R. Mori

1993-01-01

The concepts and a procedure for evaluating plant community change using the squared Euclidean distance (SED) resemblance function are described. Analyses are based on the concept that Euclidean distances constitute a sample from a population of distances between sampling units (SUs) for a specific number of times and SUs. With different times, the distances will be...

The Mobile Bark Blower: An Evaluation of Performance and Costs

Treesearch

Raymond L. Sarles; David M. Emanuel

1977-01-01

A custom-built bark blower truck (MOBLOW) developed in Oregon was tested for its effectiveness in applying bark mulches, sawdust, and shavings in the eastern United States. Tests determined the bark blower's performance and cost in mulching grass-legume seedings and shrub beds with 10 bark products or wood residues. Bark blower trucks built to MOBLOW...

Low VOC Barrier Coating for Industrial Maintenance

DTIC Science & Technology

2007-11-01

Color - VOC - Total Solids (wt) - Total Solids (volume) - Percent Pigment - Stormer Viscosity - Brookfield Viscosity - Pot Life...17 NTPEP LVBC Testing (R 31-02) ●Formula - Color - VOC - Total Solids (wt) - Total Solids (volume) - Percent Pigment - Stormer ...Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using the Stormer -Type Viscometer D 610 Test Method for Evaluating Degree of

A program downloader and other utility software for the DATAC bus monitor unit

NASA Technical Reports Server (NTRS)

Novacki, Stanley M., III

1987-01-01

A set or programs designed to facilitate software testing on the DATAC Bus Monitor is described. By providing a means to simplify program loading, firmware generation, and subsequent testing of programs, the overhead involved in software evaluation is reduced and that time is used more productively in performance, analysis and improvement of current software.

NREL-Developed CUBE Helps Solve Army's Refueling Challenge | News | NREL

Science.gov Websites

Demonstration Opened Door to Idea Origins of the CUBE date to 2007 when representatives from the Army's Mobile proposed testing and evaluating some of the unit's mobile electric power systems, including a small wind to it." While the Army's original mobile electric power systems underwent testing at the

MTF Database: A Repository of Students' Academic Performance Measurements for the Development of Techniques for Evaluating Team Functioning

ERIC Educational Resources Information Center

Hsiung, Chin-Min; Zheng, Xiang-Xiang

2015-01-01

The Measurements for Team Functioning (MTF) database contains a series of student academic performance measurements obtained at a national university in Taiwan. The measurements are acquired from unit tests and homework tests performed during a core mechanical engineering course, and provide an objective means of assessing the functioning of…

Precision Pointing Control System (PPCS) star tracker test

NASA Technical Reports Server (NTRS)

1972-01-01

Tests performed on the TRW precision star tracker are described. The unit tested was a two-axis gimballed star tracker designed to provide star LOS data to an accuracy of 1 to 2 sec. The tracker features a unique bearing system and utilizes thermal and mechanical symmetry techniques to achieve high precision which can be demonstrated in a one g environment. The test program included a laboratory evaluation of tracker functional operation, sensitivity, repeatibility, and thermal stability.

Evaluation of the Impact of Kerojet (trademark) Aquarius Water Scavenger Additive on the Thermal Stability of Jet A Fuels

DTIC Science & Technology

2014-12-01

113 Figure 64 - Elemental Analysis, Typical TMS Post - Test , Post Carbon Burn-off, Hexane rinsed ............ 114 Figure 65 – SEM (20X...Agency’s Wright-Patterson Aerospace Fuels Laboratory AFRL Air Force Research Laboratory AFTSTU Aviation Fuel Thermal Stability Test Unit ARSFSS Advanced...Approved for public release; distribution unlimited. For all ARSFSS testing , SV hysteresis is measure pre- and post - test and is defined by relating

Recommendations for Evaluating Multiple Filters in Ballast Water Management Systems for US Type Approval

DTIC Science & Technology

2016-01-01

is extremely unlikely to be practicable . A second approach is to conduct a full suite of TA testing on a BWMS with a “base filter” configuration...that of full TA testing. Here, three land-based tests would be conducted, and O&M and component testing would also occur. If time or practicality ... Practical salinity units SAE Society of Automotive Engineers SDI Silt density index SOP Standard operating procedure STEP Shipboard Technology

Advanced Prototype Fan Operating Experience, Post Test Evaluation, and Refurbishment for PLSS 2.0 Test Use

NASA Technical Reports Server (NTRS)

Hodgson, Edward; Oehler, William; Dionne, Steve; Converse, David; Jennings, Mallory A.

2012-01-01

NASA s plans for Extravehicular Activity (EVA) portable life support systems for future exploration missions result in different design requirements than those which led to the combined fan / pump / separator in the current ISS Extravehicular Mobility Unit (EMU). To meet these new requirements, NASA contracted with Hamilton Sundstrand to provide two new prototype fans designed to meet anticipated future system requirements. Based on design trade studies, a high speed fan with mechanical bearing support of the rotating elements and a novel non-metallic barrier canned motor design was developed and implemented in the deliverable prototypes. The prototypes, which used two different bearing lubricants, have been extensively tested in both stand-alone and integrated system tests in NASA laboratories and proven to meet the anticipated performance requirements. Subsequently, they have been subjected to post test inspection and analysis in Hamilton Sundstrand laboratories to assess the effects of integrated operation and resultant exposure to vent loop contaminants. Results have confirmed expectations that one of the lubricants would be superior in this application and the prototype fans have been reassembled with new bearings with the superior lubricant. They have now been returned to the Johnson Space Center for further testing and maturation as part of NASA s PLSS 2.0 integrated test effort. This paper will discuss the test history of these units, resulting test data, the results of post test evaluation, and plans for further testing in the near future.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Nicholas R.; Carlsen, Brett W.; Dixon, Brent W.

Dynamic fuel cycle simulation tools are intended to model holistic transient nuclear fuel cycle scenarios. As with all simulation tools, fuel cycle simulators require verification through unit tests, benchmark cases, and integral tests. Model validation is a vital aspect as well. Although compara-tive studies have been performed, there is no comprehensive unit test and benchmark library for fuel cycle simulator tools. The objective of this paper is to identify the must test functionalities of a fuel cycle simulator tool within the context of specific problems of interest to the Fuel Cycle Options Campaign within the U.S. Department of Energy smore » Office of Nuclear Energy. The approach in this paper identifies the features needed to cover the range of promising fuel cycle options identified in the DOE-NE Fuel Cycle Evaluation and Screening (E&S) and categorizes these features to facilitate prioritization. Features were categorized as essential functions, integrating features, and exemplary capabilities. One objective of this paper is to propose a library of unit tests applicable to each of the essential functions. Another underlying motivation for this paper is to encourage an international dialog on the functionalities and standard test methods for fuel cycle simulator tools.« less

Testing practices and volume of non-Lyme tickborne diseases in the United States.

PubMed

Connally, Neeta P; Hinckley, Alison F; Feldman, Katherine A; Kemperman, Melissa; Neitzel, David; Wee, Siok-Bi; White, Jennifer L; Mead, Paul S; Meek, James I

2016-02-01

Large commercial laboratories in the United States were surveyed regarding the number of specimens tested for eight tickborne diseases in 2008. Seven large commercial laboratories reported testing a total of 2,927,881 specimens nationally (including Lyme disease). Of these, 495,585 specimens (17%) were tested for tickborne diseases other than Lyme disease. In addition to large commercial laboratories, another 1051 smaller commercial, hospital, and government laboratories in four states (CT, MD, MN, and NY) were surveyed regarding tickborne disease testing frequency, practices, and results. Ninety-two of these reported testing a total of 10,091 specimens for four tickborne diseases other than Lyme disease. We estimate the cost of laboratory diagnostic testing for non-Lyme disease tickborne diseases in 2008 to be $9.6 million. These data provide a baseline to evaluate trends in tickborne disease test utilization and insight into the burden of these diseases. Copyright © 2015 Elsevier GmbH. All rights reserved.

Investigation of Proprietary Air-Entraining Admixtures to Produce Frost- Resistant Concrete with Low Air Content

DTIC Science & Technology

1992-03-01

LABORATORY rci-dr Civil Works Investigation Studies Work Unit 31138 92 4 22096 Best Avai~lable Copy ’ p ~ o) n< w : -c rnsu on’ ratur.- 𔃼t crrJ’ria’ cr...Low Air Investigation Content Studies 6. AUTHOR(S) Work Unit 31138 Billy D. Neeley, W. E. McDonald, Michael K. Lloyd 7. PERFORMING ORGANIZATION NAME(S...as a part of Civil Works Investigation Studies Work Unit 31138 , "New Technologies for Testing and Evaluating Concrete." The study was conducted under

Stability of penicillin G sodium diluted with 0.9% sodium chloride injection or 5% dextrose injection and stored in polyvinyl chloride bag containers and elastomeric pump containers.

PubMed

Hossain, Mirza Akram; Friciu, Mihaela; Aubin, Sebastien; Leclair, Grégoire

2014-04-15

The stability of penicillin G sodium solutions stored in polyvinyl chloride (PVC) bags or elastomeric pump containers was studied. Test samples were prepared by diluting powdered penicillin G sodium (10 million units/10-mL vial) to solutions of 2,500 or 50,000 units/mL with 0.9% sodium chloride injection or 5% dextrose injection. The preparations were transferred to 250-mL PVC bags and elastomeric pump containers. All samples were prepared in triplicate and stored at 5°C. Chemical stability was measured by a stability-indicating high-performance liquid chromatographic (HPLC) assay and by pH evaluation. Particulate matter was evaluated according to compendial standards using a light-obscuration particle count test. Preparations were visually examined throughout the study. After 21 days of storage, all test samples remained chemically stable, with an HPLC assay recovery value of more than 90% of the initial value. After 28 days, all samples prepared with either diluent and stored in PVC bags, as well as the samples diluted to 2,500 units/mL with sodium chloride injection and stored in elastomeric pump containers, did not meet the recovery acceptance limit. For all test samples, the mean pH consistently decreased during storage, from about 6.4 to about 5.5. Particle counts remained acceptable throughout the study, and no change in appearance was observed. Penicillin G for injection (2,500 and 50,000 units/mL) diluted in 0.9% sodium chloride injection or 5% dextrose injection and stored at 5°C in PVC containers or elastomeric pump containers was physically and chemically stable for a period of at least 21 days.

The Effects of Unit Exercises on the Hand Grip Strength of Arm Wrestlers

ERIC Educational Resources Information Center

Yonca, Sezer S.; Engin, Çelikel B.; Serdar, Yücel A.; Mustafa, Karadag; Yüksel, Savucu

2017-01-01

The aim of this research is to evaluate the change in the hand grip strength of the male arm wrestlers before and after a unit of exercise. The participants of the research consist of sportsmen (n=16) of Firat University arm wrestling team in 18-25 age group. Within the scope of the research, all of the tests and measurements (age, length, body…

On condition evaluation of axle unit bearings of wheel pair

NASA Astrophysics Data System (ADS)

Glotov, V. V.; Romashchenko, M. A.; Ostroumov, I. V.; Kondratiev, Il V.

2018-03-01

At present, axle units of freight cars undergo a complete checkup with disassembling and visual inspection of the bearing parts every five years. During an annual interim checkup, external inspection of an axle box with removed cap is carried out and the lubricant condition is checked. The state of the rolling surfaces of bearings during an interim checkup should be assessed using the known methods of nondestructive testing.

Report to the President of the United States on Sexual Assault Prevention and Response

DTIC Science & Technology

2014-11-01

established research history based on laboratory- tested principles of memory retrieval, knowledge representation, and communication. AFOSI has been using CI...analysis methods, including scientific research , data analysis, focus groups , and on -site assessments to evaluate the Department’s SAPR program...131 Report to the President of the United States on SAPR DMDC’s focus group methodology employs a standard qualitative research approach to

Acid-neutralizing capacity and sodium content of antacid products from Belgium.

PubMed

Gombatz, V W

1984-01-01

The acid-neutralizing capacity and sodium content of nine antacid products available in Belgium were evaluated and compared with typical values for Mylanta-II. Liquid and tablets of Mylanta-II have a higher acid-neutralizing capacity per unit dose than do all the other Belgian antacids tested. On a unit dose basis, the sodium contents of the Mylanta-II products are lower than those of all other Belgian antacids tested except Maalox products. Because the minimum recommended dose (MRD) of Mylanta-II liquid is 5 ml, while that of Maalox is 10 ml, the sodium content of the MRD of Mylanta-II liquid is lower than that of the MRD of any of the other Belgian liquid antacids tested.

QUEST/Ada (query utility environment for software testing of Ada: The development of a program analysis environment for Ada, task 1, phase 3

NASA Technical Reports Server (NTRS)

Brown, David B.

1991-01-01

The results of research and development efforts of the first six months of Task 1, Phase 3 of the project are presented. The goals of Phase 3 are: (1) to further refine the rule base and complete the comparative rule base evaluation; (2) to implement and evaluate a concurrency testing prototype; (3) to convert the complete (unit-level and concurrency) testing prototype to a workstation environment; and (4) to provide a prototype development document to facilitate the transfer of research technology to a working environment. These goals were partially met and the results are summarized.

Prototype solar heating and cooling systems

NASA Technical Reports Server (NTRS)

1978-01-01

Eight prototype systems were developed. The systems are 3, 25, and 75-ton size units. The manufacture, test, installation, maintenance, problem resolution, and performance evaluation of the systems is described. Size activities for the various systems are included.

Regional Traffic Incident Management Programs : Implementation Guide

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Air Quality Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM projects ...

Traffic conflict techniques for safety and operations : observers manual

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Institutional and Organizational Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. T...

A toolbox for alleviating traffic congestion and enhancing mobility

DOT National Transportation Integrated Search

2012-06-01

This report presents the Tolling Data Test Plan for the national evaluation of the Los Angeles (LA) Congestion Reduction Demonstration (Metro ExpressLanes) under the United States Department of Transportation (U.S. DOT) Congestion Reduction Demonstra...

Share the road campaign research study : final report

DOT National Transportation Integrated Search

2012-07-01

This report presents the Environmental Data Test Plan for the national evaluation of the Los Angeles (LA) Congestion Reduction Demonstration (Metro ExpressLanes) under the United States Department of Transportation (U.S. DOT) Congestion Reduction Dem...

PrismTech Data Distribution Service Java API Evaluation

NASA Technical Reports Server (NTRS)

Riggs, Cortney

2008-01-01

My internship duties with Launch Control Systems required me to start performance testing of an Object Management Group's (OMG) Data Distribution Service (DDS) specification implementation by PrismTech Limited through the Java programming language application programming interface (API). DDS is a networking middleware for Real-Time Data Distribution. The performance testing involves latency, redundant publishers, extended duration, redundant failover, and read performance. Time constraints allowed only for a data throughput test. I have designed the testing applications to perform all performance tests when time is allowed. Performance evaluation data such as megabits per second and central processing unit (CPU) time consumption were not easily attainable through the Java programming language; they required new methods and classes created in the test applications. Evaluation of this product showed the rate that data can be sent across the network. Performance rates are better on Linux platforms than AIX and Sun platforms. Compared to previous C++ programming language API, the performance evaluation also shows the language differences for the implementation. The Java API of the DDS has a lower throughput performance than the C++ API.

Pigment tests evaluated by a model of chromatic discrimination.

PubMed

Smith, V C; Pokorny, J; Yeh, T

1993-08-01

Clinical color-vision tests are evaluated within the framework of a model of chromatic discrimination in terms of cone excitation. The motivation for this study was to derive a method for evaluation of test design, test sensitivity, and observer performance. The discrimination model is based on the assumption that chromatic discrimination is mediated in two independent channels, one for short-wavelength cones and one for long- and middle-wavelength cones. Luminance-dependent templates are derived for each channel, and they describe chromatic-discrimination behavior of the young color-normal observer. The templates incorporate receptor- and opponent-level gain controls. We show how the chromaticities of clinical tests can be calculated in cone-excitation units and how discrimination behavior on the tests can be plotted on the templates. The tests include the Farnsworth-Munsell 100-hue, the Farnsworth Panel D-15, the Farnsworth Panel D-15 desaturated, the American Optical Hardy-Rand-Rittler, the Farnsworth F2 plate, the Standard Pseudoisochromatic Plates, Part II, the Ishihara, and the Minimalist tests. Clinical-test data collected on young color-normal observers at different illumination levels show the validity of the techniques.

EMC Test Report Electrodynamic Dust Shield

NASA Technical Reports Server (NTRS)

Carmody, Lynne M.; Boyette, Carl B.

2014-01-01

This report documents the Electromagnetic Interference E M I evaluation performed on the Electrodynamic Dust Shield (EDS) which is part of the MISSE-X System under the Electrostatics and Surface Physics Laboratory at Kennedy Space Center. Measurements are performed to document the emissions environment associated with the EDS units. The purpose of this report is to collect all information needed to reproduce the testing performed on the Electrodynamic Dust Shield units, document data gathered during testing, and present the results. This document presents information unique to the measurements performed on the Bioculture Express Rack payload; using test methods prepared to meet SSP 30238 requirements. It includes the information necessary to satisfy the needs of the customer per work order number 1037104. The information presented herein should only be used to meet the requirements for which it was prepared.

Premission and postmission simulation studies of the foot-controlled maneuvering unit for Skylab experiment T-020. [astronaut maneuvering equipment - space environment simulation

NASA Technical Reports Server (NTRS)

Hewes, D. E.; Glover, K. E.

1975-01-01

A Skylab experiment was conducted to study the maneuvering capabilities of astronauts using a relatively simple self-locomotive device, referred to as the foot-controlled maneuvering unit, and to evaluate the effectiveness of ground-based facilities simulating the operation of this device in weightless conditions of space. Some of the special considerations given in the definition and development of the experiment as related to the two ground-based simulators are reviewed. These simulators were used to train the test subjects and to obtain baseline data which could be used for comparison with the in-flight tests that were performed inside the Skylab orbital workshop. The results of both premission and postmission tests are discussed, and subjective comparisons of the in-flight and ground-based test conditions are presented.

Using Satellite Imagery to Assess Large-Scale Habitat Characteristics of Adirondack Park, New York, USA

NASA Astrophysics Data System (ADS)

McClain, Bobbi J.; Porter, William F.

2000-11-01

Satellite imagery is a useful tool for large-scale habitat analysis; however, its limitations need to be tested. We tested these limitations by varying the methods of a habitat evaluation for white-tailed deer ( Odocoileus virginianus) in the Adirondack Park, New York, USA, utilizing harvest data to create and validate the assessment models. We used two classified images, one with a large minimum mapping unit but high accuracy and one with no minimum mapping unit but slightly lower accuracy, to test the sensitivity of the evaluation to these differences. We tested the utility of two methods of assessment, habitat suitability index modeling, and pattern recognition modeling. We varied the scale at which the models were applied by using five separate sizes of analysis windows. Results showed that the presence of a large minimum mapping unit eliminates important details of the habitat. Window size is relatively unimportant if the data are averaged to a large resolution (i.e., township), but if the data are used at the smaller resolution, then the window size is an important consideration. In the Adirondacks, the proportion of hardwood and softwood in an area is most important to the spatial dynamics of deer populations. The low occurrence of open area in all parts of the park either limits the effect of this cover type on the population or limits our ability to detect the effect. The arrangement and interspersion of cover types were not significant to deer populations.

Pearson's chi-square test and rank correlation inferences for clustered data.

PubMed

Shih, Joanna H; Fay, Michael P

2017-09-01

Pearson's chi-square test has been widely used in testing for association between two categorical responses. Spearman rank correlation and Kendall's tau are often used for measuring and testing association between two continuous or ordered categorical responses. However, the established statistical properties of these tests are only valid when each pair of responses are independent, where each sampling unit has only one pair of responses. When each sampling unit consists of a cluster of paired responses, the assumption of independent pairs is violated. In this article, we apply the within-cluster resampling technique to U-statistics to form new tests and rank-based correlation estimators for possibly tied clustered data. We develop large sample properties of the new proposed tests and estimators and evaluate their performance by simulations. The proposed methods are applied to a data set collected from a PET/CT imaging study for illustration. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

USNO GPS program

NASA Technical Reports Server (NTRS)

Putkovich, K.

1981-01-01

Initial test results indicated that the Global Positioning System/Time Transfer Unit (GPS/TTU) performed well within the + or - 100 nanosecond range required by the original system specification. Subsequent testing involved the verification of GPS time at the master control site via portable clocks and the acquisition and tracking of as many passes of the space vehicles currently in operation as possible. A description and discussion of the testing, system modifications, test results obtained, and an evaluation of both GPS and the GPS/TTU are presented.

A PREP Panel, Practice-Based, Evaluation of the Handling of the Kerr Demi-Ultra Light Curing Unit.

PubMed

Burke, F J Trevor; Crisp, Russell J

2015-09-01

This paper describes the handling evaluation (by a group of practice-based researchers, the PREP Panel) of a recently introduced Light Curing Unit (LCU), the Kerr Demi-Ultra, which possesses a number of novel features such as its ultracapacitor power source, and the Light Emitting Diodes (LEDs) which provide the light output being placed close to the tip of the light guide. CPD/CLINICAL RELEVANCE: Testing of new devices and materials with respect to their handling is of importance, given that an easy to handle device should produce better clinical results than one which is difficult to use.

United States Air Force F-35A Operational Basing Environmental Impact Statement. Volume 1

DTIC Science & Technology

2013-09-01

Evaluation (FDE) program and Weapons School (WS) beddown, the F-22 designator was used. Subsequent testing , development, and deployment resulted in...Initial F-35A Operational Basing EIS Final, September 2013 contract to develop the JSF ( designated the F-35 Lightning II). Since then, testing of F...of the aircraft even with system failures. Throughout the design and testing process, safety initiatives took previous best practices for single

Testing of DentStat (trademark) and Competing Dental Materials

DTIC Science & Technology

2014-06-13

NAVAL MEDICAL RESEARCH UNIT SAN ANTONIO TESTING OF DENTST AT™ AND COMPETING DENTAL MATERIALS Y OON HWANG PHD, JONATHAN STAHL DDS PHD, WAYNE M. D...LtCOL Wen Lien of the US Air Force Dental Evaluation and Consultation Service for assistance with the strength testing. 1 Reviewed and Approved by...direct dental repair materials. They are made of calcium or strontium aluminofluoro-silicate glass powder (base) combined with a water-soluble polymer

Evaluation of a commercial automatic treatment planning system for liver stereotactic body radiation therapy treatments.

PubMed

Gallio, Elena; Giglioli, Francesca Romana; Girardi, Andrea; Guarneri, Alessia; Ricardi, Umberto; Ropolo, Roberto; Ragona, Riccardo; Fiandra, Christian

2018-02-01

Automated treatment planning is a new frontier in radiotherapy. The Auto-Planning module of the Pinnacle 3 treatment planning system (TPS) was evaluated for liver stereotactic body radiation therapy treatments. Ten cases were included in the study. Six plans were generated for each case by four medical physics experts. The first two planned with Pinnacle TPS, both with manual module (MP) and Auto-Planning one (AP). The other two physicists generated two plans with Monaco TPS (VM). Treatment plan comparisons were then carried on the various dosimetric parameters of target and organs at risk, monitor units, number of segments, plan complexity metrics and human resource planning time. The user dependency of Auto-Planning was also tested and the plans were evaluated by a trained physician. Statistically significant differences (Anova test) were observed for spinal cord doses, plan average beam irregularity, number of segments, monitor units and human planning time. The Fisher-Hayter test applied to these parameters showed significant statistical differences between AP e MP for spinal cord doses and human planning time; between MP and VM for monitor units, number of segments and plan irregularity; for all those between AP and VM. The two plans created by different planners with AP were similar to each other. The plans created with Auto-Planning were comparable to the manually generated plans. The time saved in planning enables the planner to commit more resources to more complex cases. The independence of the planner enables to standardize plan quality. Copyright © 2018 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Use of technology as an evaluation tool of clinical care in preterm newborns.

PubMed

Mendes, Izabel; Carvalho, Manoel de; Almeida, Rosimary Terezinha; Moreira, Maria Elizabeth

2006-01-01

To assess the use of the Neonatal Therapeutic Intervention Scoring System (NTISS) as a tool to quantify the use of technology in neonatal intensive care units, in order to detect discrepancies in the care provided to high-risk newborn infants. Prospective, descriptive, observational study about the use of technology in two neonatal intensive care units (one public and one private). The NTISS was calculated on a daily basis up to the discharge or death of preterm newborns with gestational age equal to or less than 32 weeks. We gathered data about prenatal clinical conditions, birth characteristics, and conditions on admission to the intensive care unit, as well as about the morbidities developed during the hospital stay. The risks of preterm newborns were adjusted by means of the Score for Neonatal Acute Physiology, Perinatal Extension, Version II (SNAPPE-II). Student's t test, chi-square test, Fisher's exact test, and the Mann-Whitney/Wilcoxon's test were used for the descriptive analysis. The study was approved by the local Research and Ethics Committee. We assessed 44 newborn infants from the public intensive care unit and 52 from the private one. On admission, the severity score (SNAPPE-II) and the overall NTISS were statistically similar in both care units. The curve for the use of technology showed a gradual and progressive decreasing pattern in both care units up to the 31st day. Thereafter, there was a continuous downward trend in the private care unit, but a significant increase in the overall NTISS in the public care unit. The patients from the public care unit developed more morbidities than those from the private unit. Patients with similar clinical pictures can be treated with different levels of technological resources. This may have a direct impact on morbidities and on healthcare costs. The NTISS allowed monitoring healthcare and proved efficient in detecting discrepancies in practices that could influence clinical outcomes and operating costs.

Myasthenic decrement and myasthenic myopathy. A study on the effects of thymectomy.

PubMed Central

Pinelli, P; Arrigo, A; Moglia, A

1975-01-01

Motor unit action potentials, M responses to repetitive nerve stimulation, and anticholinesterase tests were investigated in 12 myasthenic patients before and after thymectomy. In six of them the endarterial acetylcholine test was also carried out. Responsiveness to ACTH or to prednisone treatment was evaluated before and after thymectomy. The typical myasthenic presynaptic disorders were improved by thymectomy, while signs of myasthenic myopathy (according to Rowland's definition) were apparently increased. This process of 'functional myopathophanerosis' is discussed and explained in terms of a previous presynaptic disorder blocking the voluntary recruitment threshold of those motor units which are most affected at both presynaptic and postsynaptic level. Images PMID:168321

Evaluation of marginal and internal gap of three-unit metal framework according to subtractive manufacturing and additive manufacturing of CAD/CAM systems.

PubMed

Kim, Dong-Yeon; Kim, Eo-Bin; Kim, Hae-Young; Kim, Ji-Hwan; Kim, Woong-Chul

2017-12-01

To evaluate the fit of a three-unit metal framework of fixed dental prostheses made by subtractive and additive manufacturing. One master model of metal was fabricated. Twenty silicone impressions were made on the master die, working die of 10 poured with Type 4 stone, and working die of 10 made of scannable stone. Ten three-unit wax frameworks were fabricated by wax-up from Type IV working die. Stereolithography files of 10 three-unit frameworks were obtained using a model scanner and three-dimensional design software on a scannable working die. The three-unit wax framework was fabricated using subtractive manufacturing (SM) by applying the prepared stereolithography file, and the resin framework was fabricated by additive manufacturing (AM); both used metal alloy castings for metal frameworks. Marginal and internal gap were measured using silicone replica technique and digital microscope. Measurement data were analyzed by Kruskal-Wallis H test and Mann-Whitney U-test (α=.05). The lowest and highest gaps between premolar and molar margins were in the SM group and the AM group, respectively. There was a statistically significant difference in the marginal gap among the 3 groups ( P <.001). In the marginal area where pontic was present, the largest gap was 149.39 ± 42.30 µm in the AM group, and the lowest gap was 24.40 ± 11.92 µm in the SM group. Three-unit metal frameworks made by subtractive manufacturing are clinically applicable. However, additive manufacturing requires more research to be applied clinically.

A Multilevel Analysis of a Guided Inquiry Curriculum Unit on Motion and Force for a Diverse Student Population in "Ability-Grouped" Classrooms

ERIC Educational Resources Information Center

Rethinam, Vasuki; Lynch, Sharon J.

2011-01-01

This study is an evaluation of "Exploring Motion and Forces: Speed, Acceleration, and Friction" ("M&F") developed by ARIES of the Harvard-Smithsonian Center for Astrophysics (2001). Although "M&F" has been used in many schools and field-tested, it has never been evaluated in rigorous experimental or…

An Evaluation of Research Training: The Testing, Research, and Data Processing Unit of the University Counseling Center. Research Report #5-88.

ERIC Educational Resources Information Center

Thompson, Chalmer E.; Sedlacek, William E.

The relative contributions of a research assistantship experience to graduate training programs in counseling psychology and student personnel were evaluated. The following areas were assessed: (1) the extent to which research competencies are enhanced among former research assistants; (2) the extent to which attitudes toward research are enhanced…

Correlation Between Stress and Quality of Life Experienced by Caregivers: Perception of a Group of Healthcare Professionals.

PubMed

Silva, Bhárbara Karolline Rodrigues; Quaresma, Fernando Rodrigues Peixoto; Maciel, Erika da Silva; Figueiredo, Francisco Winter Dos Santos; Sarraf, Jonathan Souza; Adami, Fernando

2017-01-01

This study aims to evaluate the relationship between perceived level of stress and quality of life of professionals working in Prompt Service Units in the city of Palmas, Tocantins. A cross-sectional study was performed among 164 professionals from Prompt Service Units. Stress levels were evaluated using the Perceived Stress Scale. The WHOQOL-bref was used to evaluate the perception of quality of life. Quantitative variables distribution was evaluated using Shapiro-Wilk's test. For the analyses of correlations among perceived level of stress, total quality of life score, and the physical health domain of the WHOQOL-bref, Pearson's correlation test was applied. The significance level adopted for this trial was 95%. The study was approved by the Committee of Ethics in Research with Human Beings. When assessing the perceived level of stress with the total quality of life score, there was no significant correlation between those variables. However, there was an association between the perceived level of stress and the physical health domain of quality of life. Perceived quality of life was correlated with the physical health domain, and this result reinforces the importance of the facets that make up this area.

A comparison of gradual sedation levels using the Comfort-B scale and bispectral index in children on mechanical ventilation in the pediatric intensive care unit

PubMed Central

Silva, Cláudia da Costa; Alves, Marta Maria Osório; El Halal, Michel Georges dos Santos; Pinheiro, Sabrina dos Santos; Carvalho, Paulo Roberto Antonacci

2013-01-01

Objective Compare the scores resulting from the Comfort-B scale with the bispectral index in children in an intensive care unit. Methods Eleven children between the ages of 1 month and 16 years requiring mechanical ventilation and sedation were simultaneously classified based on the bispectral index and the Comfort-B scale. Their behavior was recorded using digital photography, and the record was later evaluated by three independent evaluators. Agreement tests (Bland-Altman and Kappa) were then performed. The correlation between the two methods (Pearson correlation) was tested. Results In total, 35 observations were performed on 11 patients. Based on the Kappa coefficient, the agreement among evaluators ranged from 0.56 to 0.75 (p<0.001). There was a positive and consistent association between the bispectral index and the Comfort-B scale [r=0.424 (p=0.011) to r=0.498 (p=0.002)]. Conclusion Due to the strong correlation between the independent evaluators and the consistent correlation between the two methods, the results suggest that the Comfort-B scale is reproducible and useful in classifying the level of sedation in children requiring mechanical ventilation. PMID:24553512

Evaluating the Validity of Accommodations for English Learners through Evidence Based on Response Processes

ERIC Educational Resources Information Center

Crotts, Katrina M.

2013-01-01

English learners (ELs) represent one of the fastest growing student populations in the United States. Given that language can serve as a barrier in EL performance, test accommodations are provided to help level the playing field and allow ELs to better demonstrate their true performance level. Test accommodations on the computer offer the ability…

Transistor step stress testing program for JANTX2N2484

NASA Technical Reports Server (NTRS)

1979-01-01

The effect of power/temperature step stress when applied to the transistor JANTX2N2484, manufactured by Raytheon and Teledyne was evaluated. Forty-eight samples from each manufacturer were divided equally (16 per group) into three groups and submitted to the processes outlined. In addition, two control sample units were maintained for verification of the electrical parametric testing.

Operational Assessment of Color Vision

DTIC Science & Technology

2016-06-20

evaluated in this study. 15. SUBJECT TERMS Color vision, aviation, cone contrast test, Colour Assessment & Diagnosis , color Dx, OBVA 16. SECURITY...symbologies are frequently used to aid or direct critical activities such as aircraft landing approaches or railroad right-of-way designations...computer-generated display systems have facilitated the development of computer-based, automated tests of color vision [14,15]. The United Kingdom’s

Internal quality control of blood products: An experience from a tertiary care hospital blood bank from Southern Pakistan.

PubMed

Sultan, Sadia; Zaheer, Hasan Abbas; Waheed, Usman; Baig, Mohammad Amjad; Rehan, Asma; Irfan, Syed Mohammed

2018-01-01

Internal quality control (IQC) is the backbone of quality assurance program. In blood banking, the quality control of blood products ensures the timely availability of a blood component of high quality with maximum efficacy and minimal risk to potential recipients. The main objective of this study is to analyze the IQC of blood products as an indicator of our blood bank performance. An observational cross-sectional study was conducted at the blood bank of Liaquat National Hospital and Medical College, from January 2014 to December 2015. A total of 100 units of each blood components were arbitrarily chosen during the study. Packed red cell units were evaluated for hematocrit (HCT); random platelet concentrates were evaluated for pH, yield, and culture; fresh frozen plasma (FFP) and cryoprecipitate (CP) were evaluated for unit volume, factor VIII, and fibrinogen concentrations. A total of 400 units were tested for IQC. The mean HCT of packed red cells was 69.5 ± 7.24, and in 98% units, it met the standard (<80% of HCT). The mean platelet yield was 8.8 ± 3.40 × 10 9 /L and pH was ≥6.2 in 98% bags; cultures were negative in 97% of units tested. Mean factor VIII and fibrinogen levels were found to be 84.24 ± 15.01 and 247.17 ± 49.69 for FFP, respectively. For CP, mean factor VIII and fibrinogen level were found to be 178.75 ± 86.30 and 420.7 ± 75.32, respectively. The IQC of blood products at our blood bank is in overall compliance and met recommended international standards. Implementation of standard operating procedures, accomplishment of standard guidelines, proper documentation with regular audit, and staff competencies can improve the quality performance of the transfusion services.

ETV REPORT: CERTEK, INC. 1414RH FORMALDEHYDE GENERATOR/NEUTRALIZER

EPA Science Inventory

The Environmental Technology Verification report discusses the technology and performance of the 1414RH Formaldehyde Generator/Neuralizer, a biological decontamination device manufactured by CERTEK, Inc. The unit was tested by evaluating its ability to decontaminate seven types ...

Development of the North American cargo securement standard

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Benefit-Cost Analysis (BCA) for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pr...

Improvements in Symbol Sign Design To Aid Older Drivers

DOT National Transportation Integrated Search

2012-08-01

This report presents the Traffic System Data Test Plan for the national evaluation of the Los Angeles County Congestion Reduction Demonstration (CRD) under the United States Department of Transportation (U.S. DOT) Urban Partnership Agreement (UPA) Pr...

Pressurized Slot Testing to Determine Thermo-Mechanical Properties of Lithophysal Tuff at Yucca Mountain Nevada.

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, James T.; Sobolik, Steven R.; Lee, Moo Y.

The study described in this report involves heated and unheated pressurized slot testing to determine thermo-mechanical properties of the Tptpll (Tertiary, Paintbrush, Topopah Spring Tuff Formation, crystal poor, lower lithophysal) and Tptpul (upper lithophysal) lithostratigraphic units at Yucca Mountain, Nevada. A large volume fraction of the proposed repository at Yucca Mountain may reside in the Tptpll lithostratigraphic unit. This unit is characterized by voids, or lithophysae, which range in size from centimeters to meters, making a field program an effective method of measuring bulk thermal-mechanical rock properties (thermal expansion, rock mass modulus, compressive strength, time-dependent deformation) over a range ofmore » temperature and rock conditions. The field tests outlined in this report provide data for the determination of thermo-mechanical properties of this unit. Rock-mass response data collected during this field test will reduce the uncertainty in key thermal-mechanical modeling parameters (rock-mass modulus, strength and thermal expansion) for the Tptpll lithostratigraphic unit, and provide a basis for understanding thermal-mechanical behavior of this unit. The measurements will be used to evaluate numerical models of the thermal-mechanical response of the repository. These numerical models are then used to predict pre- and post-closure repository response. ACKNOWLEDGEMENTS The authors would like to thank David Bronowski, Ronnie Taylor, Ray E. Finley, Cliff Howard, Michael Schuhen (all SNL) and Fred Homuth (LANL) for their work in the planning and implementation of the tests described in this report. This is a reprint of SAND2004-2703, which was originally printed in July 2004. At that time, it was printed for a restricted audience. It has now been approved for unlimited release.« less

International Environmental Evaluation for the Helical Screw Expander Generator Unit Projects in Cesano, Italy and Broadlands, New Zealand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webb, J.W.; Mezga, L.J.; Reed, A.W.

1981-08-01

The objectives of the Helical Screw Expander (HSE) Generator Program are (1) to accelerate the development of geothermal resources by introducing this advanced conversion technology, (2) to provide operating experience to prospective users of the equipment, and (3) to collect data on the performance and reliability of the equipment under various geothermal resource conditions. The participants hope to achieve these goals by testing a small-scale, transportable HSE generator at existing geothermal test facilities that produce fluids of different salinity, temperature and pressure conditions. This Environmental Evaluation has been prepared, using available information, to analyze the environmental consequences of testing themore » HSE generator. Its purpose is to support a decision on the need for a complete environmental review of the HSE program under the terms of Executive Order 121 14, ''Environmental Effects Abroad of Major federal Actions''. This Executive Order requires review of projects which involve the release of potentially toxic effluents that are strictly regulated in the United States, or which may have significant environmental effects on the global commons, on natural or ecological resources of international significance, or on the environment of non-participating countries. The final guidelines implementing the provisions of the Executive Order for DOE have been published. This evaluation deals with testing to be conducted at Cesano, Italy by the designated contractor of the Italian government, the Ente Narionale per l'Energia Ellectrica (ENEL), and at Broadlands, New Zealand by the Ministry of Works and Development of New Zealand. Testing at Cerro Prieto, Mexico has already been completed by the Comision Federal de Electricidad and is not evaluated in this report.« less

JPS heater and sensor lightning qualification

NASA Technical Reports Server (NTRS)

Cook, M.

1989-01-01

Simulated lightning strike testing of the Redesigned Solid Rocket Motor (RSRM) field joint protection system heater assembly was performed at Thiokol Corp., Wendover Lightning Facility. Testing consisted of subjecting the lightning evaluation test article to simulated lightning strikes and evaluating the effects of heater cable transients on cables within the systems tunnel. The maximum short circuit current coupled onto a United Space Boosters, Inc. operational flight cable within the systems tunnel, induced by transients from all cables external to the systems tunnel, was 92 amperes. The maximum open-circuit voltage coupled was 316 volts. The maximum short circuit current coupled onto a United Space Boosters, Inc. operational flight cable within the systems tunnel, induced by heater power cable transients only, was 2.7 amperes; the maximum open-circuit voltage coupled was 39 volts. All heater power cable induced coupling was due to simulated lightning discharges only, no heater operating power was applied during the test. The results showed that, for a worst-case lightning discharge, the heater power cable is responsible for a 3.9 decibel increase in voltage coupling to operational flight cables within the systems tunnel. Testing also showed that current and voltage levels coupled onto cables within the systems tunnel are partially dependant on the relative locations of the cables within the systems tunnel.

A noble technique a using force-sensing resistor for immobilization-device quality assurance: A feasibility study

NASA Astrophysics Data System (ADS)

Cho, Min-Seok; Kim, Tae-Ho; Kang, Seong-Hee; Kim, Dong-Su; Kim, Kyeong-Hyeon; Shin, Dong-Seok; Noh, Yu-Yun; Koo, Hyun-Jae; Cheon, Geum Seong; Suh, Tae Suk; Kim, Siyong

2016-03-01

Many studies have reported that a patient can move even when an immobilization device is used. Researchers have developed an immobilization-device quality-assurance (QA) system that evaluates the validity of immobilization devices. The QA system consists of force-sensing-resistor (FSR) sensor units, an electric circuit, a signal conditioning device, and a control personal computer (PC) with in-house software. The QA system is designed to measure the force between an immobilization device and a patient's skin by using the FSR sensor unit. This preliminary study aimed to evaluate the feasibility of using the QA system in radiation-exposure situations. When the FSR sensor unit was irradiated with a computed tomography (CT) beam and a treatment beam from a linear accelerator (LINAC), the stability of the output signal, the image artifact on the CT image, and changing the variation on the patient's dose were tested. The results of this study demonstrate that this system is promising in that it performed within the error range (signal variation on CT beam < 0.30 kPa, root-mean-square error (RMSE) of the two CT images according to presence or absence of the FSR sensor unit < 15 HU, signal variation on the treatment beam < 0.15 kPa, and dose difference between the presence and the absence of the FSR sensor unit < 0.02%). Based on the obtained results, we will volunteer tests to investigate the clinical feasibility of the QA system.

EMC Test Challenges for NASAs James Webb Space Telescope

NASA Technical Reports Server (NTRS)

McCloskey, John

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

EMC Test Challenges for NASA's James Webb Space Telescope

NASA Technical Reports Server (NTRS)

McCloskey, John

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

Evaluation of Acoustic Emission SHM of PRSEUS Composite Pressure Cube Tests

NASA Technical Reports Server (NTRS)

Horne, Michael R.; Madaras, Eric I.

2013-01-01

A series of tests of the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) pressure cube were conducted during third quarter 2011 at NASA Langley Research Center (LaRC) in the Combined Loads Test facility (COLTS). This is a report of the analysis of the Acoustic Emission (AE) data collected during those tests. The AE signals of the later tests are consistent with the final failure progression through two of the pressure cube panels. Calibration tests and damage precursor AE indications, from preliminary checkout pressurizations, indicated areas of concern that eventually failed. Hence those tests have potential for vehicle health monitoring.

Testing and failure analysis to improve screening techniques for hermetically sealed metallized film capacitors for low energy applications

NASA Technical Reports Server (NTRS)

1982-01-01

Effective screening techniques are evaluated for detecting insulation resistance degradation and failure in hermetically sealed metallized film capacitors used in applications where low capacitor voltage and energy levels are common to the circuitry. A special test and monitoring system capable of rapidly scanning all test capacitors and recording faults and/or failures is examined. Tests include temperature cycling and storage as well as low, medium, and high voltage life tests. Polysulfone film capacitors are more heat stable and reliable than polycarbonate film units.

Getting evidence-based pressure ulcer prevention into practice: a multi-faceted unit-tailored intervention in a hospital setting.

PubMed

Sving, Eva; Högman, Marieann; Mamhidir, Anna-Greta; Gunningberg, Lena

2016-10-01

The aim of the study was to evaluate whether a multi-faceted, unit-tailored intervention using evidenced-based pressure ulcer prevention affects (i) the performance of pressure ulcer prevention, (ii) the prevalence of pressure ulcers and (iii) knowledge and attitudes concerning pressure ulcer prevention among registered and assistant nurses. A quasi-experimental, clustered pre- and post-test design was used. Five units at a hospital setting were included. The intervention was based on the PARIHS framework and included a multi-professional team, training and repeated quality measurements. An established methodology was used to evaluate the prevalence and prevention of pressure ulcers. Nurses' knowledge and attitudes were evaluated using a validated questionnaire. A total of 506 patients were included, of whom 105 patients had a risk to develop pressure ulcer. More patients were provided pressure ulcer prevention care (P = 0·001) and more prevention care was given to each patient (P = 0·021) after the intervention. Corresponding results were shown in the group of patients assessed as being at risk for developing pressure ulcers. Nurses' knowledge about pressure ulcer prevention increased (P < 0·001). Positive attitudes towards pressure ulcer prevention remained high between pre- and post-test surveys. This multi-faceted unit-tailored intervention affected pressure ulcer prevention. Facilitation and repeated quality measurement together with constructed feedback of results seemed to be the most important factor for pressure ulcer prevention. © 2014 The Authors. International Wound Journal © 2014 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

Evaluation of fuel cell system efficiency and degradation at development and during commercialization

NASA Astrophysics Data System (ADS)

Gemmen, R. S.; Johnson, C. D.

Two primary parameters stand out for characterizing fuel cell system performance. The first and most important parameter is system efficiency. This parameter is relatively easy to define, and protocols for its assessment are already available. Another important parameter yet to be fully considered is system degradation. Degradation is important because customers desire to know how long their purchased fuel cell unit will last. The measure of degradation describes this performance factor by quantifying, for example, how the efficiency of the unit degrades over time. While both efficiency and degradation concepts are readily understood, the coupling between these two parameters must also be understood so that proper testing and evaluation of fuel cell systems is achieved. Tests not properly performed, and results not properly understood, may result in improper use of the evaluation data, producing improper R&D planning decisions and financial investments. This paper presents an analysis of system degradation, recommends an approach to its measurement, and shows how these two parameters are related and how one can be "traded-off" for the other.

Evaluating the importance of characterizing soil structure and horizons in parameterizing a hydrologic process model

USGS Publications Warehouse

Mirus, Benjamin B.

2015-01-01

Incorporating the influence of soil structure and horizons into parameterizations of distributed surface water/groundwater models remains a challenge. Often, only a single soil unit is employed, and soil-hydraulic properties are assigned based on textural classification, without evaluating the potential impact of these simplifications. This study uses a distributed physics-based model to assess the influence of soil horizons and structure on effective parameterization. This paper tests the viability of two established and widely used hydrogeologic methods for simulating runoff and variably saturated flow through layered soils: (1) accounting for vertical heterogeneity by combining hydrostratigraphic units with contrasting hydraulic properties into homogeneous, anisotropic units and (2) use of established pedotransfer functions based on soil texture alone to estimate water retention and conductivity, without accounting for the influence of pedon structures and hysteresis. The viability of this latter method for capturing the seasonal transition from runoff-dominated to evapotranspiration-dominated regimes is also tested here. For cases tested here, event-based simulations using simplified vertical heterogeneity did not capture the state-dependent anisotropy and complex combinations of runoff generation mechanisms resulting from permeability contrasts in layered hillslopes with complex topography. Continuous simulations using pedotransfer functions that do not account for the influence of soil structure and hysteresis generally over-predicted runoff, leading to propagation of substantial water balance errors. Analysis suggests that identifying a dominant hydropedological unit provides the most acceptable simplification of subsurface layering and that modified pedotransfer functions with steeper soil-water retention curves might adequately capture the influence of soil structure and hysteresis on hydrologic response in headwater catchments.

Supplemental treatment of air in airborne infection isolation rooms using high-throughput in-room air decontamination units.

PubMed

Bergeron, Vance; Chalfine, Annie; Misset, Benoît; Moules, Vincent; Laudinet, Nicolas; Carlet, Jean; Lina, Bruno

2011-05-01

Evidence has recently emerged indicating that in addition to large airborne droplets, fine aerosol particles can be an important mode of influenza transmission that may have been hitherto underestimated. Furthermore, recent performance studies evaluating airborne infection isolation (AII) rooms designed to house infectious patients have revealed major discrepancies between what is prescribed and what is actually measured. We conducted an experimental study to investigate the use of high-throughput in-room air decontamination units for supplemental protection against airborne contamination in areas that host infectious patients. The study included both intrinsic performance tests of the air-decontamination unit against biological aerosols of particular epidemiologic interest and field tests in a hospital AII room under different ventilation scenarios. The unit tested efficiently eradicated airborne H5N2 influenza and Mycobacterium bovis (a 4- to 5-log single-pass reduction) and, when implemented with a room extractor, reduced the peak contamination levels by a factor of 5, with decontamination rates at least 33% faster than those achieved with the extractor alone. High-throughput in-room air treatment units can provide supplemental control of airborne pathogen levels in patient isolation rooms. Copyright © 2011 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

An IMU Evaluation Method Using a Signal Grafting Scheme

PubMed Central

Niu, Xiaoji; Wang, Qiang; Li, You; Zhang, Quan; Jiang, Peng

2016-01-01

As various inertial measurement units (IMUs) from different manufacturers appear every year, it is not affordable to evaluate every IMU through tests. Therefore, this paper presents an IMU evaluation method by grafting data from the tested IMU to the reference data from a higher-grade IMU. The signal grafting (SG) method has several benefits: (a) only one set of field tests with a higher-grade IMU is needed, and can be used to evaluate numerous IMUs. Thus, SG is effective and economic because all data from the tested IMU is collected in the lab; (b) it is a general approach to compare navigation performances of various IMUs by using the same reference data; and, finally, (c) through SG, one can first evaluate an IMU in the lab, and then decide whether to further test it. Moreover, this paper verified the validity of SG to both medium- and low-grade IMUs, and presents and compared two SG strategies, i.e., the basic-error strategy and the full-error strategy. SG provided results similar to field tests, with a difference of under 5% and 19.4%–26.7% for tested tactical-grade and MEMS IMUs. Meanwhile, it was found that dynamic IMU errors were essential to guarantee the effect of the SG method. PMID:27294932

Streamflow trends in the United States

USGS Publications Warehouse

Lins, H.F.; Slack, J.R.

1999-01-01

Secular trends in streamflow are evaluated for 395 climate-sensitive streamgaging stations in the conterminous United States using the non-parametric Mann-Kendall test. Trends are calculated for selected quantiles of discharge, from the 0th to the 100th percentile, to evaluate differences between low-, medium-, and high-flow regimes during the twentieth century. Two general patterns emerge; trends are most prevalent in the annual minimum (Q0) to median (Q50) flow categories and least prevalent in the annual maximum (Q100) category; and, at all but the highest quantiles, streamflow has increased across broad sections of the United States. Decreases appear only in parts of the Pacific Northwest and the Southeast. Systematic patterns are less apparent in the Q100 flow. Hydrologically, these results indicate that the conterminous U.S. is getting wetter, but less extreme.

Evaluation of the use of various rat strains for immunogenic potency tests of Sabin-derived inactivated polio vaccines.

PubMed

Someya, Yuichi; Ami, Yasushi; Takai-Todaka, Reiko; Fujimoto, Akira; Haga, Kei; Murakami, Kosuke; Fujii, Yoshiki; Shirato, Haruko; Oka, Tomoichiro; Shimoike, Takashi; Katayama, Kazuhiko; Wakita, Takaji

2018-03-01

Slc:Wistar rats have been the only strain used in Japan for purpose of evaluating a national reference vaccine for the Sabin-derived inactivated polio vaccine (sIPV) and the immunogenicity of sIPV-containing products. However, following the discovery that the Slc:Wistar strain was genetically related to the Fischer 344 strain, other "real" Wistar strains, such as Crlj:WI, that are available worldwide were tested in terms of their usefulness in evaluating the immunogenicity of the past and current lots of a national reference vaccine. The response of the Crlj:WI rats against the serotype 1 of sIPV was comparable to that of the Slc:Wistar rats, while the Crlj:WI rats exhibited a higher level of response against the serotypes 2 and 3. The immunogenic potency units of a national reference vaccine determined using the Slc:Wistar rats were reproduced on tests using the Crlj:WI rats. These results indicate that a titer of the neutralizing antibody obtained in response to a given dose of sIPV cannot be directly compared between these two rat strains, but that, more importantly, the potency units are almost equivalent for the two rat strains. Copyright © 2018 International Alliance for Biological Standardization. Published by Elsevier Ltd. All rights reserved.

Multi-hundred kilowatt roll ring assembly

NASA Technical Reports Server (NTRS)

Jacobson, Peter E.

1985-01-01

A program was completed to develop an evaluation unit of a high power rotary transfer device for potential application in a space environment. This device was configured around a Roll Ring concept which performs the same function as a slip ring/brush assembly with a rolling instead of sliding interface. An eight circuit Evaluation Unit (EU) and a portable Test Fixture (TF) were designed and fabricated. The EU was designed to transfer currents to 200 amperes at a potential of as high as 500 volts for an ultimate 100 kW/circuit transfer capability. The EU was evaluated in vacuum at dc transfer currents of 50 to 200 amperes at voltages to 10 volts and at 500 volts at 2 amperes. Power transfer to levels of 2 kW through each of the eight circuits was completed. Power transfer in vacuum at levels and efficiencies not previously achieved was demonstrated. The terminal-to-terminal resistance was measured to be greater than 0.42 milliohms which translates to an efficiency at 100 kW of 99.98 percent. The EU and TF have been delivered to the Lewis Research Center and are being prepared tor testing at increased power levels and for life testing, which will include both dc and ac power.

Final report on testing of TOPAZ II unit Ya-21u: Output power characteristics and system capabilities

NASA Astrophysics Data System (ADS)

Luchau, David W.; Sinkevich, Valery G.; Wernsman, Bernard; Mulder, Daniel M.

1996-03-01

A final report on the output power characteristics and capabilities of the TOPAZ II Space Nuclear Power Unit Ya-21u is presented. Results showed that after a total of almost 8,000 hours of system testing in the U.S. and Russia, several emergency cooldowns, and three inadvertent air introductions to the interelectrode gap (IEG) that the TOPAZ II demonstrates the potential for providing reliable power in a space environment. Output power optimizations and system characteristics following a shock and vibration test are shown. These tests were performed using electrical heaters that simulate nuclear fuel heating. This paper will focus primarily on the changes in output power characteristics over the lifetime of Ya-21u. All U.S. testing was conducted at the Thermionic System Evaluation Test (TSET) Facility of the New Mexico Engineering Research Institute (NMERI) as a part of the TOPAZ International Program (TIP). TIP is managed by the Air Force Phillips Laboratory (PL) for the Ballistic Missile Defense Organization (BMDO).

Wear resistance of ductile irons

NASA Astrophysics Data System (ADS)

Lerner, Y. S.

1994-06-01

This study was undertaken to evaluate the wear resistance of different grades of ductile iron as alterna-tives to high- tensile- strength alloyed and inoculated gray irons and bronzes for machine- tool and high-pressure hydraulic components. Special test methods were employed to simulate typical conditions of reciprocating sliding wear with and without abrasive- contaminated lubricant for machine and press guideways. Quantitative relationships were established among wear rate, microstructure and micro-hardness of structural constituents, and nodule size of ductile iron. The frictional wear resistance of duc-tile iron as a bearing material was tested with hardened steel shafts using standard test techniques under continuous rotating movement with lubricant. Lubricated sliding wear tests on specimens and compo-nents for hydraulic equipment and apparatus were carried out on a special rig with reciprocating motion, simulating the working conditions in a piston/cylinder unit in a pressure range from 5 to 32 MPa. Rig and field tests on machine- tool components and units and on hydraulic parts have confirmed the test data.

The 737 graphite composite flight spoiler flight service evaluation

NASA Technical Reports Server (NTRS)

Coggeshall, R. L.

1982-01-01

A flight service report was prepared which covers the flight service experience of 111 graphite epoxy spoilers on 737 transport aircraft and related ground based environmental exposure of graphite epoxy material specimens. Spoilers were installed on 28 aircraft representing seven major airlines operating throughout the world. Tests of removed spoilers after the seventh year of service continue to indicate modest changes in composite strength properties. Two spoilers were tested, one with 6 and one with 7 years of service, and both had residual strengths that fall within the original static strength scatter band. Both these units had typical service included discrepancies when tested. Based on visual, ultrasonic, and destructive inspection there continues to be no evidence of moisture migration into the honeycomb core and no core corrosion in the deployed units.

First flight test results of the Simplified Aid For EVA Rescue (SAFER) propulsion unit

NASA Technical Reports Server (NTRS)

Meade, Carl J.

1995-01-01

The Simplified Aid for EVA Rescue (SAFER) is a small, self-contained, propulsive-backpack system that provides free-flying mobility for an astronaut engaged in a space walk, also known as extravehicular activity (EVA.) SAFER contains no redundant systems and is intended for contingency use only. In essence, it is a small, simplified version of the Manned Maneuvering Unit (MMU) last flown aboard the Space Shuttle in 1985. The operational SAFER unit will only be used to return an adrift EVA astronaut to the spacecraft. Currently, if an EVA crew member inadvertently becomes separated from the Space Shuttle, the Orbiter will maneuver to within the crew member's reach envelope, allowing the astronaut to regain contact with the Orbiter. However, with the advent of operations aboard the Russian MIR Space Station and the International Space Station, the Space Shuttle will not be available to effect a timely rescue. Under these conditions, a SAFER unit would be worn by each EVA crew member. Flight test of the pre-production model of SAFER occurred in September 1994. The crew of Space Shuttle Mission STS-64 flew a 6.9 hour test flight which included performance, flying qualities, systems, and operational utility evaluations. We found that the unit offers adequate propellant and control authority to stabilize and enable the return of a tumbling/separating crew member. With certain modifications, production model of SAFER can provide self-rescue capability to a separated crew member. This paper will present the program background, explain the flight test results and provide some insight into the complex operations of flight test in space.

Commercial vehicle operations one-stop electronic purchasing and processing, ITS operational test : final evaluation report

DOT National Transportation Integrated Search

1997-09-01

The United States Department of Transportations (USDOTs) National ITS Program : Plan describes the national strategy for deploying advanced technologies and services into our : transportation system. To emphasize the need-driven (rather than te...

Measurement-based evaluation of noncomposite steel girder bridges.

DOT National Transportation Integrated Search

2000-02-01

The results from an experimental study into the behavior of noncomposite slab-on-steel girder bridges are presented. Two bridge : units were tested under increasing static loads beyond first yield of the girders with a flatbed trailer loaded with con...

[Access to primary healthcare services: still a way to go].

PubMed

Mendes, Antônio da Cruz Gouveia; Miranda, Gabriella Morais Duarte; Figueiredo, Karla Erika Gouveia; Duarte, Petra Oliveira; Furtado, Betise Mery Alencar Sousa Macau

2012-11-01

This study seeks to evaluate accessibility to the Basic Units of the Family Health Strategy (ESF-UB) and Traditional Basic Units (BU-T) in the city of Recife in 2009. Data were collected through three instruments: a roadmap for systematic observation of the units and questionnaires for users and professional units. This is a descriptive cross-sectional study using a quantitative approach, and 1180 users, 61 doctors and 56 nurses were interviewed. The results showed good ties and recognition of users whereby primary healthcare is seen as the access portal to the health system. In the comparison between ESF-UB and UB-T, evaluations are always more favorable to the family healthcare strategy, though with relatively insignificant differences. The overall result revealed widespread dissatisfaction with the difficulty of obtaining drugs and taking tests, and also with the waiting times and access to specialized care. This showed the existence of organizational problems that may constitute barriers limiting accessibility to basic healthcare services for users.

Commercial Absorption Heat Pump Water Heater: Beta Prototype Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geoghegan, Patrick; Ally, Moonis; Sharma, Vishaldeep

2016-10-14

The Beta version of the Commercial Absorption Heat Pump (CAHP) water heater was evaluated in the environmental chambers at Oak Ridge National Laboratory. Ambient air conditions ranged from 17 to 75 oF and inlet water temperatures ranged from 100 to 120oF in order to capture trends in performance. The unit was operated under full fire (100%) and partial fire (55%). The unit was found to perform at 90% of the project goal at the design conditions of 47oF ambient and 100oF water temperatures. The trends across the full range of environmental conditions were as expected for ambient air temperatures abovemore » 32oF. Below this temperature and for the full fire condition, frost accumulated on the evaporator coil. In future work a defrost strategy will be enabled, the unit will be thoroughly cleaned of an oil contamination and the rectifier will be reconfigured in order to meet the design goals and have a field test unit ready in early 2017.« less

Drug education in bolivian schools: A feasibility study for cross-cultural application of a preventive curricular unit

NASA Astrophysics Data System (ADS)

Gonzalez, Gerardo M.; Moreno, Veronica Kaune

1995-11-01

The purpose of this study was to test the feasibility of adapting and implementing in La Paz, Bolivia a drug education course originally developed for use in the middle schools in the United States. On the basis of teacher and student evaluations, it was concluded that the unit is a viable, culturally relevant and effective method of drug education in the public and private schools in La Paz. Implications for the prevention of other health-related problems and for implementation of a demandreduction strategy to prevent drug abuse throughout the Americas are discussed.

NASA Glenn Research Center Support of the ASRG Project

NASA Technical Reports Server (NTRS)

Wilson, Scott D.; Wong, Wayne A.

2014-01-01

A high efficiency radioisotope power system is being developed for long-duration NASA space science missions. The U.S. Department of Energy (DOE) managed a flight contract with Lockheed Martin Space Systems Company (LMSSC) to build Advanced Stirling Radioisotope Generators (ASRGs), with support from NASA Glenn Research Center (GRC). Sunpower Inc. held two parallel contracts to produce Advanced Stirling Convertors (ASCs), one with DOELockheed Martin to produce ASC-F flight units, and one with GRC for the production of ASC-E3 engineering unit pathfinders that are built to the flight design. In support of those contracts, GRC provided testing, materials expertise, government furnished equipment, inspections, and related data products to DOELockheed Martin and Sunpower. The technical support includes material evaluations, component tests, convertor characterization, and technology transfer. Material evaluations and component tests have been performed on various ASC components in order to assess potential life-limiting mechanisms and provide data for reliability models. Convertor level tests have been used to characterize performance under operating conditions that are representative of various mission conditions. Technology transfers enhanced contractor capabilities for specialized production processes and tests. Despite termination of flight ASRG contract, NASA continues to develop the high efficiency ASC conversion technology under the ASC-E3 contract. This paper describes key government furnished services performed for ASRG and future tests used to provide data for ongoing reliability assessments.

[Impact of the incorporation of a nurse in an inflammatory bowel disease unit].

PubMed

Amo, Leticia; González-Lama, Yago; Suárez, Cristina; Blázquez, Isabel; Matallana, Virginia; Calvo, Marta; de la Revilla, Juan; Vera, María I; Abreu, Luis

2016-05-01

Multidisciplinary units are needed because of the growing complexity and volume of patients with inflammatory bowel disease (IBD). To evaluate the healthcare, economic and research impact of incorporating a nurse into the IBD unit of the Puerta de Hierro Majadahonda University Hospital. We prospectively recorded the activity carried out by the nurse of the IBD unit from March 2010 to December 2014. During this period, healthcare demand progressively increased, with 1,558 patients being attended by our unit. The healthcare provided by the nurse included 5,293 electronic mails and 678 telephone calls. We estimated that this activity represented a saving of 3,504 in-person medical consultations and 852 accident and emergency department visits. Other activities consisted of monitoring treatments with biological and non-biological agents (8,371 laboratory tests), extraction of 342 blood samples, follow-up of 1047 diagnostic tests and consultations with other medical specialties, health education in self-administration of drugs in 114 patients, the performance of 158 granulocyte apheresis procedures, and participation in 25 research projects. The incorporation of a specialised nurse in an IBD unit had major economic, healthcare and research benefits. Copyright © 2016. Published by Elsevier Espana.

Identification of fuel cycle simulator functionalities for analysis of transition to a new fuel cycle

DOE PAGES

Brown, Nicholas R.; Carlsen, Brett W.; Dixon, Brent W.; ...

2016-06-09

Dynamic fuel cycle simulation tools are intended to model holistic transient nuclear fuel cycle scenarios. As with all simulation tools, fuel cycle simulators require verification through unit tests, benchmark cases, and integral tests. Model validation is a vital aspect as well. Although compara-tive studies have been performed, there is no comprehensive unit test and benchmark library for fuel cycle simulator tools. The objective of this paper is to identify the must test functionalities of a fuel cycle simulator tool within the context of specific problems of interest to the Fuel Cycle Options Campaign within the U.S. Department of Energy smore » Office of Nuclear Energy. The approach in this paper identifies the features needed to cover the range of promising fuel cycle options identified in the DOE-NE Fuel Cycle Evaluation and Screening (E&S) and categorizes these features to facilitate prioritization. Features were categorized as essential functions, integrating features, and exemplary capabilities. One objective of this paper is to propose a library of unit tests applicable to each of the essential functions. Another underlying motivation for this paper is to encourage an international dialog on the functionalities and standard test methods for fuel cycle simulator tools.« less

Hardware Demonstration: Radiated Emissions as a Function of Common Mode Current

NASA Technical Reports Server (NTRS)

Mc Closkey, John; Roberts, Jen

2016-01-01

This presentation describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

A preliminary test of an ecological classification system for the Oconee National Forest using forest inventory and analysis data

Treesearch

W. Henry McNab; Ronald B. Stephens; Richard D. Rightmyer; Erika M. Mavity; Samuel G. Lambert

2012-01-01

An ecological classification system (ECS) has been developed for use in evaluating management, conservation and restoration options for forest and wildlife resources on the Oconee National Forest. Our study was the initial evaluation of the ECS to determine if the units at each level differed in potential productivity. We used loblolly pine (Pinus taeda...

United States Department of Defense: Agency Financial Report Fiscal Year 2014

DTIC Science & Technology

2014-01-01

Defense Review (QDR) 2014 to Congress in March 2014. The QDR is a legislatively -mandated report, issued every four years, that evaluates the...Operational Test & Evaluation General Counsel, DoD ASD ( Legislative Affairs) ATSD (Public Affairs) DoD Chief Information Officer Director, Net...in Billions Breakout Accounts Payable $19.8 1% Military Retirement and Employment Benefits $2,334.0 95% Environmental and Disposal Liabilities

Peer Ratings: Scoring Strategy Development and Reliability Demonstration on Air Force Basic Trainees. Final Report.

ERIC Educational Resources Information Center

Borman, Walter C.; Rosse, Rodney L.

As an alternative for or adjunct to paper-and-pencil tests for predicting personnel performance, the United States Air Force studied the use of peer ratings as an evaluative tool. Purpose of this study was to evaluate the psychometric characteristics of peer ratings among Air Force basic trainees. Peer ratings were obtained from more than 27,000…

Evaluation of the Affymetrix CytoScan® Dx Assay for Developmental Delay

PubMed Central

Webb, Bryn D.; Scharf, Rebecca J.; Spear, Emily A.; Edelmann, Lisa J.; Stroustrup, Annemarie

2015-01-01

The goal of molecular cytogenetic testing for children presenting with developmental delay is to identify or exclude genetic abnormalities that are associated with cognitive, behavioral, and/or motor symptoms. Until 2010, chromosome analysis was the standard first-line genetic screening test for evaluation of patients with developmental delay when a specific syndrome was not suspected. In 2010, The American College of Medical Genetics and several other groups recommended chromosomal microarray (CMA) as the first-line test in children with developmental delays, multiple congenital anomalies, and/or autism. This test is able to detect regions of genomic imbalances at a much finer resolution than G-banded karyotyping. Until recently, no CMA testing had been approved by the United States Food and Drug Administration (FDA). This review will focus on the use of the Affymetrix CytoScan® Dx Assay, the first CMA to receive FDA approval for the genetic evaluation of individuals with developmental delay. PMID:25350348

The Statistical Loop Analyzer (SLA)

NASA Technical Reports Server (NTRS)

Lindsey, W. C.

1985-01-01

The statistical loop analyzer (SLA) is designed to automatically measure the acquisition, tracking and frequency stability performance characteristics of symbol synchronizers, code synchronizers, carrier tracking loops, and coherent transponders. Automated phase lock and system level tests can also be made using the SLA. Standard baseband, carrier and spread spectrum modulation techniques can be accomodated. Through the SLA's phase error jitter and cycle slip measurements the acquisition and tracking thresholds of the unit under test are determined; any false phase and frequency lock events are statistically analyzed and reported in the SLA output in probabilistic terms. Automated signal drop out tests can be performed in order to trouble shoot algorithms and evaluate the reacquisition statistics of the unit under test. Cycle slip rates and cycle slip probabilities can be measured using the SLA. These measurements, combined with bit error probability measurements, are all that are needed to fully characterize the acquisition and tracking performance of a digital communication system.

Tdp studies and tests for C. A. Energia Electrica de Venezuela (enelven) at planta ramon laguna, units RL-17 and RL-10. Volume 1. Executive summary, RL-17 test report, and gas conversion proposals. Export trade information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-03-28

The study, conducted by Babcock and Wilcox, was funded by the U.S. Trade and Development agency on behalf of Enelven. In order to maximize generated power output and minimize operating costs at Planta Ramon Laguna, tests were done to evaluate the condition of equipment at the plant. In order to identify any damage and determine the operating output of each unit, assessments were done of the furnaces, boilers, generators and boiler feed pumps being used in the plant. The report presents the results of these tests. This is the first of three volumes and it is divided into the followingmore » sections: (1) Executive Summary; (2) Hydrogen Damage Assessment; (3) RL-17 Gas Conversion Proposal; (4) RL-10 and RL-11 Gas Conversion Proposals.« less

A proposed USAF fatigue evaluation program based upon recent systems experience

NASA Technical Reports Server (NTRS)

Haviland, G. P.; Purkey, G. F.

1972-01-01

The United States Air Force has published a document entitled Aircraft Structural Integrity Program. One phase of the program is concerned with the fatigue life certification of all types of military aircraft. The document describes the criteria, analyses, and tests that are necessary in order to satisfy the USAF fatigue life requirement. Some recent and valid criticism has been directed toward the document, particularly the fatigue-life requirements contained in it. Some changes are proposed based on surveys conducted in the United States and abroad as well as some recent systems' experience. The surveys covered both military and civilian organizations. The fatigue certification case histories of selected military and commercial aircraft are presented. The design development element tests, preproduction design verification tests, and full-scale fatigue tests of each are described. A brief status report on the revisions to the MIL-A-008860 series specifications is included.

Mod-2 wind turbine system development. Volume 2: Detailed report

NASA Technical Reports Server (NTRS)

1982-01-01

Progress in the design, fabrication, and testing of a wind turbine system is reported. The development of the MOD-2 wind turbine through acceptance testing and initial operational evaluation is documented. The MOD-2 project intends to develop early commercialization of wind energy. The first wind turbine farm (three MOD-2 units) are now being operated at the Bonneville Power Administration site near Goldendale, Washington.

Least Squares Method for Equating Logistic Ability Scales: A General Approach and Evaluation. Iowa Testing Programs Occasional Papers, Number 30.

ERIC Educational Resources Information Center

Haebara, Tomokazu

When several ability scales in item response models are separately derived from different test forms administered to different samples of examinees, these scales must be equated to a common scale because their units and origins are arbitrarily determined and generally different from scale to scale. A general method for equating logistic ability…

An OEF/OIF study of close combat missions using small unmanned aircraft systems

NASA Astrophysics Data System (ADS)

Lifschitz, Gabriel; Tierney, Richard J.; Vitali, Juan A.

2007-04-01

The Small Unmanned Aircraft System (SUAS) is a rucksack portable aerial observation vehicle designed to supplement reconnaissance, surveillance and target acquisition tasks of an infantry company. The Raven is an earlier version of the SUAS. Raven is an Urgent Material Release (UMR) acquisition and has been used for the past two years by selected Army units in Operations Enduring Freedom and Iraqi Freedom (OEF/OIF). Army Test and Evaluation Command-led surveys were used to assess the capabilities and limitations of the Raven in OEF/OIF. Results and analyses of the surveys indicate that Raven enhances situational awareness of a small unit in urban areas and in selected close combat missions. Users of the Raven state it is easy to use, although there are major issues with frequency de-confliction, airspace management, short endurance, and sensor performance. The SUAS is a program of record and completed developmental and operational testing in preparation for full rate production. This paper addresses the SUAS effectiveness, suitability, and survivability evaluation strategy based on actual testing of the system. During the Initial Operational Test (IOT), the SUAS was found to be effective with limitations in a set of 21 closed combat missions and two call for fire tests for which it was tested. Low Mean Time Between Operational Mean Failure (MTBOMF) and human factors issues make the system suitable with limitations. Acoustic (audible to the human ear) and electronic vulnerabilities make the system non-survivable in most combat scenarios. The SUAS was found to be useful as an extra asset usable in certain infantry company close combat missions where terrain and visual line of sight give the system an advantage over traditional reconnaissance patrols. Army aviation and infantry units uncover new ways every day to use this portable "eye in the sky", especially when unmanned aerial reconnaissance assets are in premium demand. A discussion on changes in doctrine with the SUAS and how it will be integrated into future combat systems for the Army completes the evaluation analysis and its likely benefits to the Soldier.

Maintaining Adequate Carbon Dioxide Washout for an Advanced Extravehicular Mobility Unit

NASA Technical Reports Server (NTRS)

Chullen, Cinda; Navarro, Moses; Conger, Bruce; Korona, Adam; McMillin, Summer; Norcross, Jason; Swickrath, Mike

2013-01-01

Over the past several years, NASA has realized tremendous progress in technology development that is aimed at the production of an Advanced Extravehicular Mobility Unit (AEMU). Of the many functions provided by the spacesuit and portable life support subsystem within the AEMU, delivering breathing gas to the astronaut along with removing the carbon dioxide (CO2) remains one of the most important environmental functions that the AEMU can control. Carbon dioxide washout is the capability of the ventilation flow in the spacesuit helmet to provide low concentrations of CO2 to the crew member to meet breathing requirements. CO2 washout performance is a critical parameter needed to ensure proper and sufficient designs in a spacesuit and in vehicle applications such as sleep stations and hygiene compartments. Human testing to fully evaluate and validate CO2 washout performance is necessary but also expensive due to the levied safety requirements. Moreover, correlation of math models becomes challenging because of human variability and movement. To supplement human CO2 washout testing, a breathing capability will be integrated into a suited manikin test apparatus to provide a safe, lower cost, stable, easily modeled alternative to human testing. Additionally, this configuration provides NASA Johnson Space Center (JSC) the capability to evaluate CO2 washout under off-nominal conditions that would otherwise be unsafe for human testing or difficult due to fatigue of a test subject. Testing has been under way in-house at JSC and analysis has been initiated to evaluate whether the technology provides sufficient performance in ensuring that the CO2 is removed sufficiently and the ventilation flow is adequate for maintaining CO2 washout in the AEMU spacesuit helmet of the crew member during an extravehicular activity. This paper will review recent CO2 washout testing and analysis activities, testing planned in-house with a spacesuit simulator, and the associated analytical work along with insights from the medical aspect on the testing.

Design and fabrication of a prototype for an automatic transport system for transferring human and other wastes to an incinerator unit onboard spacecraft, phase A

NASA Technical Reports Server (NTRS)

Labak, L. J.; Remus, G. A.; Mansnerus, R.

1971-01-01

Three transport system concepts were experimentally evaluated for transferring human and nonhuman wastes from a collection site to an incineration unit onboard spacecraft. The operating parameters, merits, and shortcomings of a porous-pneumatic, nozzle-pneumatic, and a mechanical screw-feed system were determined. An analysis of the test data was made and a preliminary design of two prototype systems was prepared.

Mixed Methods Approach to Identify Factors and the Extent to Which They Influence Medical/Surgical Prime Vendor Use

DTIC Science & Technology

2014-03-27

2009). Choosing the Right Type of Rotation in PCA and EFA. JALT Testing & Evaluation Newsletter , 13 (3), 20-25. 102 Bryman , A . (2006). Integrating...FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A . APPROVED FOR PUBLIC RELEASE...official policy or position of the United States Air Force, Department of Defense, or the United States government. This material is declared a work of

Units of Distinction: Creating a Blueprint for Recognition of High-Performing Medical-Surgical Nursing Units.

PubMed

Jeffery, Alvin D; Mosier, Sammie; Baker, Allison; Korwek, Kimberly; Borum, Cindy; Englebright, Jane

2018-02-01

Hospital medical-surgical (M/S) nursing units are responsible for up to 28 million encounters annually, yet receive little attention from professional organizations and national initiatives targeted to improve quality and performance. We sought to develop a framework recognizing high-performing units within our large hospital system. This was a retrospective data analysis of M/S units throughout a 168-hospital system. Measures represented patient experience, employee engagement, staff scheduling, nursing-sensitive patient outcomes, professional practices, and clinical process measures. Four hundred ninety units from 129 hospitals contributed information to test the framework. A manual scoring system identified the top 5% and recognized them as a "Unit of Distinction." Secondary analyses with machine learning provided validation of the proposed framework. Similar to external recognition programs, this framework and process provide a holistic evaluation useful for meaningful recognition and lay the groundwork for benchmarking in improvement efforts.

Evaluation of adenosine triphosphate test for cleaning assessment of gastroscopes and the effect on workload in a busy endoscopy center.

PubMed

Schmitt, Cristiane; Pires Maciel, Amanda Luiz; Boszczowski, Icaro; da Silva, Thaís Pereira; Neves, Eliane Aparecida Job; Rossini, Giulio Fabio; Rizek, Camila; Costa, Silvia Figueiredo; Lourenço, Rogério Ferreira; Alfa, Michelle J

2018-05-18

Using adenosine triphosphate (ATP) tests to assess manual cleaning of gastroscopes and to determine the associated workload in a busy endoscopy unit. Patient-used gastroscopes were sampled before and after cleaning to assess ATP levels, bioburden, and protein. Samples were collected by flushing 20 mL of sterile water through the biopsy port to the distal end. Time spent for reprocessing and performing the ATP test was recorded. Twenty-four samples were collected from 10 gastroscopes. After manual cleaning, 14/24 (58.3%) samples had no microbial growth (mean, 21 colony-forming units/cm 2 ), and in 22/24 (91.7%) samples the protein was undetectable (mean, 0.04 µg/cm 2 ). ATP test was above the cutoff (200 relative light units [RLU]) in 17/24 (70.8%) samples (mean, 498 RLU). After the second cleaning, 11/17 (64.7%) gastroscopes still failed the ATP test (mean, 321.2 RLU). The mean time spent to perform manual cleaning and ATP tests was 16 and 8 minutes, respectively. Hence, each test increased the length of time for cleaning plus testing cleanliness by 50%. Further studies regarding the optimal cutoff for ATP tests are needed. ATP tests for cleaning monitoring are easy to perform and provide immediate feedback to the team. However, the increased workload needs to be considered. Copyright © 2018 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Evaluation of Low-Tech Indoor Remediation Methods ...

EPA Pesticide Factsheets

Report This study identified, collected, evaluated, and summarized available articles, reports, guidance documents, and other pertinent information related to common housekeeping activities within the United States. This resulted in a summary compendium including relevant information about multiple low-tech cleaning methods from the literature search results. Through discussion and prioritization, an EPA project team, made up of several EPA scientists and emergency responders, focused the information into a list of 14 housekeeping activities for decontamination evaluation testing. These types of activities are collectively referred to as “low-tech” remediation methods because of the comparative simple tools, equipment, and operations involved. Similarly, eight common household surfaces were chosen that were contaminated using three different contamination conditions. Thirty-three combinations of methods and surfaces were chosen for testing under the three contamination conditions for a total of 99 tests.

Design of an ITS-Level advanced traffic management system: a human factors perspective

DOT National Transportation Integrated Search

2012-07-01

This report presents the Ridesharing Data Test Plan for the national evaluation of the Los Angeles (L.A.) County Congestion Reduction Demonstration (CRD) under the United States Department of Transportation (U.S. DOT) Urban Partnership Agreement (UPA...

Prototype solar heating and cooling systems

NASA Technical Reports Server (NTRS)

1978-01-01

A collection of monthly status reports on the development of eight prototype solar heating and cooling systems is presented. The effort calls for the development, manufacture, test, system installation, maintenance, problem resolution, and performance evaluation. The systems are 3, 25, and 75 ton size units.

Training Feedback Handbook. Research Product 83-7.

ERIC Educational Resources Information Center

Burnside, Billy L.; And Others

This handbook is designed to assist training developers and evaluators in structuring their collection of feedback data. Addressed first are various methods for collecting feedback data, including informal feedback, existing unit performance records, questionnaires, structured interviews, systematic observation, and testing. The next chapter, a…

Incident Management : Successful Practices : A Cross-Cutting Study : Improving Mobility And Saving Lives

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Traveler Response Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pro...

Impact of local/short haul operations on driver fatigue : focus group summary and analysis

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Institutional and Organizational Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the Dallas U.S. 75 Integrated Corridor Management (ICM) Initiative Demonstrati...

Prototype solar heating and cooling systems

NASA Technical Reports Server (NTRS)

1978-01-01

A collection of monthly status reports are given on the development of eight prototype solar heating and cooling systems. This effort calls for the development, manufacturing, test, system installation, maintenance, problem resolution, and performance evaluation. The systems are 3-, 25-, and 75-ton size units.

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: BIOQUELL, INC. CLARIS C HYDROGEN PEROXIDE GAS GENERATOR

EPA Science Inventory

The Environmental Technology Verification report discusses the technology and performance of the Clarus C Hydrogen Peroxide Gas Generator, a biological decontamination device manufactured by BIOQUELL, Inc. The unit was tested by evaluating its ability to decontaminate seven types...

7 CFR 319.73-1 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Administrator of the Animal and Plant Health Inspection Service, United States Department of Agriculture, or any... for commercial resale. Intended use includes, but is not limited to, evaluation, testing, or market...

7 CFR 319.73-1 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Administrator of the Animal and Plant Health Inspection Service, United States Department of Agriculture, or any... for commercial resale. Intended use includes, but is not limited to, evaluation, testing, or market...

7 CFR 319.73-1 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Administrator of the Animal and Plant Health Inspection Service, United States Department of Agriculture, or any... for commercial resale. Intended use includes, but is not limited to, evaluation, testing, or market...

7 CFR 319.73-1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Administrator of the Animal and Plant Health Inspection Service, United States Department of Agriculture, or any... for commercial resale. Intended use includes, but is not limited to, evaluation, testing, or market...

7 CFR 319.73-1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) ANIMAL AND PLANT HEALTH INSPECTION SERVICE... Administrator of the Animal and Plant Health Inspection Service, United States Department of Agriculture, or any... for commercial resale. Intended use includes, but is not limited to, evaluation, testing, or market...

Integrated corridor management initiative : demonstration phase evaluation, San Diego technical capability analysis test plan.

DOT National Transportation Integrated Search

1998-11-01

The purpose of this working paper is to present estimates of potential safety benefits resulting from full implementation of Intelligent Transportation Systems (ITS) in the United States. These estimates were derived by integrating results from a num...

Meeting the Customer's Needs for Mobility and Safety During Construction and Maintenance Operations

DOT National Transportation Integrated Search

2011-01-01

This report presents the Survey, Interviews, and Workshops Test Plan for the national evaluation of the Seattle/Lake Washington Corridor (LWC) Urban Partnership Agreement (UPA) under the United States Department of Transportation (U.S. DOT) UPA Progr...

Volvo Trucks field operational test : evaluation of advanced safety systems for heavy truck tractors

DOT National Transportation Integrated Search

2005-02-15

The Intelligent Vehicle Initiative (IVI) was established by the United States Department of Transportation as an integral part of the Intelligent Transportation System (ITS) program. By reducing the probability of motor vehicle collisions, the IVI wa...

Usefulness of routine preoperative testing in a developing country: a prospective study

PubMed Central

Bordes, Julien; Cungi, Pierre-Julien; Savoie, Pierre-Henry; Bonnet, Stéphane; Kaiser, Eric

2015-01-01

Introduction The assessment of anesthetic risks is an essential component of preoperative evaluation. In developing world, preanesthesia evaluation may be challenging because patient's medical history and records are scare, and language barrier limits physical examination. Our objective was to evaluate the impact of routine preoperative testing in a low-resources setting. Methods Prospective observational study performed in a French forward surgical unit in Abidjan, Ivory Coast. 201 patients who were scheduled for non urgent surgery were screened with routine laboratory exams during preoperative evaluation. Changes in surgery were assessed (delayed or scheduled). Results Abnormal hemoglobin findings were reported in 35% of patients, abnormal WBC count in 11,1% of patients, abnormal platelets in 15,3% of patients. Positive HIV results were found in 8,3% of cases. Routine tests represented 43,6% of changes causes. Conclusion Our study showed that in a developing country, routine preoperative tests showed abnormal results up to 35% of cases, and represented 43,5% of delayed surgery causes. The rate of tests leading to management changes varied widely, from 0% to 8,3%. These results suggested that selected tests would be useful to diagnose diseases that required treatment before non urgent surgery. However, larger studies are needeed to evaluate the cost/benefit ratio and the clinical impact of such a strategy. PMID:26516395

Design, synthesis and biological evaluation of di-substituted cinnamic hydroxamic acids bearing urea/thiourea unit as potent histone deacetylase inhibitors.

PubMed

Ning, Chengqing; Bi, Yanjing; He, Yujun; Huang, WenYuan; Liu, Lifei; Li, Yi; Zhang, Sihan; Liu, Xiaoyu; Yu, Niefang

2013-12-01

A novel class of di-substituted cinnamic hydroxamic acid derivatives containing urea or thiourea unit was designed, synthesized and evaluated as HDAC inhibitors. All tested compounds demonstrated significant HDAC inhibitory activities and anti-proliferative effects against diverse human tumor cell lines. Among them, 7l exhibited most potent pan-HDAC inhibitory activity, with an IC50 value of 130 nM. It also showed strong cellular inhibition against diverse cell lines including HCT-116, MCF-7, MDB-MB-435 and NCI-460, with GI50 values of 0.35, 0.22, 0.51 and 0.48 μM, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of fiber reinforced polymers using active infrared thermography system with thermoelectric cooling modules

NASA Astrophysics Data System (ADS)

Chady, Tomasz; Gorący, Krzysztof

2018-04-01

Active infrared thermography is increasingly used for nondestructive testing of various materials. Properties of this method are creating a unique possibility to utilize it for inspection of composites. In the case of active thermography, an external energy source is usually used to induce a thermal contrast inside tested objects. The conventional heating methods (like halogen lamps or flash lamps) are utilized for this purpose. In this study, we propose to use a cooling unit. The proposed system consists of a thermal imaging infrared camera, which is used to observe the surface of the inspected specimen and a specially designed cooling unit with thermoelectric modules (the Peltier modules).

Corrective Action Investigation Plan for Corrective Action Unit 560: Septic Systems, Nevada Test Site, Nevada with ROTC1, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grant Evenson

2008-05-01

Corrective Action Unit (CAU) 560 is located in Areas 3 and 6 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 560 is comprised of the seven corrective action sites (CASs) listed below: • 03-51-01, Leach Pit • 06-04-02, Septic Tank • 06-05-03, Leach Pit • 06-05-04, Leach Bed • 06-59-03, Building CP-400 Septic System • 06-59-04, Office Trailer Complex Sewage Pond • 06-59-05, Control Point Septic System These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend correctivemore » action alternatives. Additional information will be obtained by conducting a corrective action investigation before evaluating corrective action alternatives and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable corrective action alternatives that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on January 22, 2008, by representatives from the Nevada Division of Environmental Protection; U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office; Stoller-Navarro Joint Venture; and National Security Technologies, LLC. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 560.« less

Test results of six-month test of two water electrolysis systems

NASA Technical Reports Server (NTRS)

Mills, E. S.; Wells, G. W.

1972-01-01

The two water electrolysis systems used in the NASA space station simulation 90-day manned test of a regenerative life support system were refurbished as required and subjected to 26-weeks of testing. The two electrolysis units are both promising systems for oxygen and hydrogen generation and both needed extensive long-term testing to evaluate the performance of the respective cell design and provide guidance for further development. Testing was conducted to evaluate performance in terms of current, pressure, variable oxygen demands, and orbital simulation. An automatic monitoring system was used to record, monitor and printout performance data at one minute, ten minute or one-hour intervals. Performance data is presented for each day of system operation for each module used during the day. Failures are analyzed, remedial action taken to eliminate problems is discussed and recommendations for redesign for future space applications are stated.

Evaluation of marginal and internal gap of three-unit metal framework according to subtractive manufacturing and additive manufacturing of CAD/CAM systems

PubMed Central

Kim, Dong-Yeon; Kim, Eo-Bin; Kim, Hae-Young; Kim, Ji-Hwan

2017-01-01

PURPOSE To evaluate the fit of a three-unit metal framework of fixed dental prostheses made by subtractive and additive manufacturing. MATERIALS AND METHODS One master model of metal was fabricated. Twenty silicone impressions were made on the master die, working die of 10 poured with Type 4 stone, and working die of 10 made of scannable stone. Ten three-unit wax frameworks were fabricated by wax-up from Type IV working die. Stereolithography files of 10 three-unit frameworks were obtained using a model scanner and three-dimensional design software on a scannable working die. The three-unit wax framework was fabricated using subtractive manufacturing (SM) by applying the prepared stereolithography file, and the resin framework was fabricated by additive manufacturing (AM); both used metal alloy castings for metal frameworks. Marginal and internal gap were measured using silicone replica technique and digital microscope. Measurement data were analyzed by Kruskal-Wallis H test and Mann-Whitney U-test (α=.05). RESULTS The lowest and highest gaps between premolar and molar margins were in the SM group and the AM group, respectively. There was a statistically significant difference in the marginal gap among the 3 groups (P<.001). In the marginal area where pontic was present, the largest gap was 149.39 ± 42.30 µm in the AM group, and the lowest gap was 24.40 ± 11.92 µm in the SM group. CONCLUSION Three-unit metal frameworks made by subtractive manufacturing are clinically applicable. However, additive manufacturing requires more research to be applied clinically. PMID:29279766

Tailoring Antibody Testing and How to Use it in the Calculated Panel Reactive Antibody Era: The Northwestern University Experience

PubMed Central

Tambur, Anat R.; Leventhal, Joseph; Kaufman, Dixon B.; Friedewald, John; Miller, Joshua; Abecassis, Michael M.

2014-01-01

Background Patients with human leukocyte antigen antibodies constitute a significantly disadvantaged population among those awaiting renal transplantation. We speculated that more understanding of the patients’ antibody makeup would allow a more “immunologic” evaluation of crossmatch data, facilitate the use of virtual crossmatch (XM), and lead to more transplantability of these patients. Methods We retrospectively compared the transplantability and transplant outcome of two consecutive patient populations transplanted in our center. Group I (n=374) was evaluated using solid-phase base testing for determination of percentage panel reactive antibody (“PRA screen”) with limited antibody identification testing. Group II (n=333) was tested in a more comprehensive manner with major emphasis on antibody identification, antibody strength assignment, and the use of pronase for crossmatch. Results Given this approach, 49% (166/333) of the transplanted patients in group II were sensitized compared with 40% (150/374) of the recipients in group I; P=0.012. Transplant outcome at 1-year posttransplant was similar in both groups. Conclusions We conclude that comprehensive evaluation of human leukocyte antigen sensitization and application of immunologic in analyzing compatibility between donor and recipient can increase the transplantability of sensitized patients while maintaining similar outcome. Our approach is in line with United Network for Organ Sharing new guidelines for calculated panel reactive antibody and virtual XM analysis. We hope this report will prompt additional transplant programs to consider how they will use the new United Network for Organ Sharing algorithms. PMID:18946342

Operational field evaluation of the PAC-MAG man-portable magnetometer array

NASA Astrophysics Data System (ADS)

Keranen, Joe; Topolosky, Zeke; Schultz, Gregory; Miller, Jonathan

2013-06-01

Detection and discrimination of unexploded ordnance (UXO) in areas of prior conflict is of high importance to the international community and the United States government. For humanitarian applications, sensors and processing methods need to be robust, reliable, and easy to train and implement using indigenous UXO removal personnel. This paper describes system characterization, system testing, and a continental United States (CONUS) Operational Field Evaluations (OFE) of the PAC-MAG man-portable UXO detection system. System testing occurred at a government test facility in June, 2010 and December, 2011 and the OFE occurred at the same location in June, 2012. NVESD and White River Technologies personnel were present for all testing and evaluation. The PAC-MAG system is a manportable magnetometer array for the detection and characterization of ferrous UXO. System hardware includes four Cesium vapor magnetometers for detection, a Real-time Kinematic Global Position System (RTK-GPS) for sensor positioning, an electronics module for merging array data and WiFi communications and a tablet computer for transmitting and logging data. An odometer, or "hipchain" encoder, provides position information in GPS-denied areas. System software elements include data logging software and post-processing software for detection and characterization of ferrous anomalies. The output of the post-processing software is a dig list containing locations of potential UXO(s), formatted for import into the system GPS equipment for reacquisition of anomalies. Results from system characterization and the OFE will be described.

Physical Compatibility of Sodium Glycerophosphate and Calcium Gluconate in Pediatric Parenteral Nutrition Solutions.

PubMed

MacKay, Mark; Anderson, Collin

2015-08-01

The solubility of inorganic calcium and phosphate in parenteral solutions can be complicated in pediatrics due to the dosing of calcium and phosphorus at the saturation point. The purpose of this study was to test the solubility of sodium glycerophosphate (NaGP) with calcium gluconate in pediatric parenteral nutrition (PN) solutions. Five PN solutions were compounded by adding calcium gluconate at 10, 20, 30, 40, and 50 mEq/L and corresponding concentrations of NaGP at 10, 20, 30, 40, and 50 mmol/L. Each of the 5 solutions was compounded using 1.5% and 4% amino acids, cysteines, and lipids. Compatibility was evaluated by visual inspection (precipitation, haze, and color change). Solutions were evaluated microscopically for any microcrystals and measured by a turbidimeter for changes in turbidity. Solutions were further analyzed using United States Pharmacopeia 788 standards. Six hundred seventy-one PN solutions were compounded at various concentrations and evaluated for visual stability. Compatibility testing showed no changes in the PN solution in any of the concentrations tested. Microscopically, no microcrystals were detected. The turbidimeter measurements had changes of ≤ 0.14 nephelometric turbidity units for all test solutions. There were no visual changes in any of the 671 PN solutions. It is recommended that NaGP replace sodium phosphate in PN solutions. This would eliminate the concern of calcium and phosphorus precipitation and the need of any saturation curves. © 2014 American Society for Parenteral and Enteral Nutrition.

Corrective Action Investigation Plan for Corrective Action Unit 413: Clean Slate II Plutonium Dispersion (TTR) Tonopah Test Range, Nevada, Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthews, Patrick; Burmeister, Mark; Gallo, Patricia

Corrective Action Unit (CAU) 413 is located on the Tonopah Test Range, which is approximately 130 miles northwest of Las Vegas, Nevada, and approximately 40 miles southeast of Tonopah, Nevada. The CAU 413 site consists of the release of radionuclides to the surface and shallow subsurface from the conduct of the Clean Slate II (CSII) storage–transportation test conducted on May 31, 1963. CAU 413 includes one corrective action site (CAS), TA-23-02CS (Pu Contaminated Soil). The known releases at CAU 413 are the result of the atmospheric deposition of contamination from the 1963 CSII test. The CSII test was a non-nuclearmore » detonation of a nuclear device located inside a reinforced concrete bunker covered with 2 feet of soil. This test dispersed radionuclides, primarily plutonium, on the ground surface. The presence and nature of contamination at CAU 413 will be evaluated based on information collected from a corrective action investigation (CAI). The investigation is based on the data quality objectives (DQOs) developed on June 17, 2015, by representatives of the Nevada Division of Environmental Protection; the U.S. Air Force; and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 413. The CAI will include radiological surveys, geophysical surveys, collection and analyses of soil samples, and assessment of investigation results. The collection of soil samples will be accomplished using both probabilistic and judgmental sampling approaches. To facilitate site investigation and the evaluation of DQO decisions, the releases at CAU 413 have been divided into seven study groups.« less

Emergency Department Evaluation of Traumatic Brain Injury in the United States, 2009–2010

PubMed Central

Korley, Frederick K.; Kelen, Gabor D.; Jones, Courtney M.; Diaz-Arrastia, Ramon

2015-01-01

Objective Determine the dimensions of traumatic brain injury (TBI) evaluation in U.S. emergency department (EDs) to inform potential application of novel diagnostic tests. Setting United States EDs. Participants National Hospital Ambulatory Medical Care Survey of ED visits in 2009 and 2010 where TBI was evaluated (1) and diagnosed clinically, or (2) with head CT scan. Design Retrospective cross-sectional. Results TBI was evaluated during 4.8 (95% CI: 4.2–5.4) million visits/year; and head CT scan was performed in 82% of TBI evaluations (3.9 [95% CI: 3.4–4.4] million visits/year). TBI was diagnosed in 52% of evaluations (2.5 [95% CI: 2.1–2.8] million visits/year). Among those who received head CTs, 9% had CT evidence of traumatic abnormalities. Among patients evaluated for TBI who had a Glasgow Coma Scale recorded, 94.5% were classified as mild TBI, 2.1% as moderate TBI and 3.5% as severe TBI. Among patients with ICD9-C-M codes permitting the calculation of Head AIS scores 9.0%, 85.0%, 2.5%, 3.2%, 0.3% and 0% had Head AIS scores of 1,2,3,4,5,6 respectively. Of patients evaluated for TBI, 31% had other head/face/neck injuries; 10% had spine and back injuries; 7% had torso injuries; and 14% had extremity injuries. Conclusion The ED is the main gateway to medical care for millions of patients evaluated for TBI each year. Novel diagnostic tests are need to improve ED diagnosis and management of TBI. PMID:26360006

United States Air Force Statistical Digest, Fiscal Year 1967, Twenty Second Edition

DTIC Science & Technology

1967-09-30

tests as part of the Air Force’s support of the National Sonic Boom Evaluation Program. (FOUO) 18 January 1967 A Titan III-C launched a second. group...Strategic Air Command and the North American Air Defense Command participated in a joint training exercise, TOP RUNG XV. The operation evaluated ...SnlA1’IXIIC • IlEI’EIlSIVE Figbter Interceptor !I . . . . . . Airborne Barly Warning and Control • Pofenae Syatem Evaluation .. • Air Defenee Mila11e

Health Technology Assessment for Molecular Diagnostics: Practices, Challenges, and Recommendations from the Medical Devices and Diagnostics Special Interest Group.

PubMed

Garfield, Susan; Polisena, Julie; S Spinner, Daryl; Postulka, Anne; Y Lu, Christine; Tiwana, Simrandeep K; Faulkner, Eric; Poulios, Nick; Zah, Vladimir; Longacre, Michael

2016-01-01

Health technology assessments (HTAs) are increasingly used to inform coverage, access, and utilization of medical technologies including molecular diagnostics (MDx). Although MDx are used to screen patients and inform disease management and treatment decisions, there is no uniform approach to their evaluation by HTA organizations. The International Society for Pharmacoeconomics and Outcomes Research Devices and Diagnostics Special Interest Group reviewed diagnostic-specific HTA programs and identified elements representing common and best practices. MDx-specific HTA programs in Europe, Australia, and North America were characterized by methodology, evaluation framework, and impact. Published MDx HTAs were reviewed, and five representative case studies of test evaluations were developed: United Kingdom (National Institute for Health and Care Excellence's Diagnostics Assessment Programme, epidermal growth factor receptor tyrosine kinase mutation), United States (Palmetto's Molecular Diagnostic Services Program, OncotypeDx prostate cancer test), Germany (Institute for Quality and Efficiency in Healthcare, human papillomavirus testing), Australia (Medical Services Advisory Committee, anaplastic lymphoma kinase testing for non-small cell lung cancer), and Canada (Canadian Agency for Drugs and Technologies in Health, Rapid Response: Non-invasive Prenatal Testing). Overall, the few HTA programs that have MDx-specific methods do not provide clear parameters of acceptability related to clinical and analytic performance, clinical utility, and economic impact. The case studies highlight similarities and differences in evaluation approaches across HTAs in the performance metrics used (analytic and clinical validity, clinical utility), evidence requirements, and how value is measured. Not all HTAs are directly linked to reimbursement outcomes. To improve MDx HTAs, organizations should provide greater transparency, better communication and collaboration between industry and HTA stakeholders, clearer links between HTA and funding decisions, explicit recognition of and rationale for differential approaches to laboratory-developed versus regulatory-approved test, and clear evidence requirements. Copyright © 2016 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Improvement of Radiological Teaching - Effects of Focusing of Learning Targets and Increased Consideration of Learning Theory Knowledge.

PubMed

Wirth, Stefan; William, York-Alexander; Paolini, Marco; Wirth, Kathrin; Maxien, Daniel; Reiser, Maximilian; Fischer, Martin R

2018-02-01

 Based on evaluation and examination results of students, a necessity for improvement of so far purely instructor-based radiological teaching at the local institution was determined. Aim of our study was to use one out of eight seminars to exemplify adaptation of the teaching concept according to learning theory knowledge, to determine the resulting effects and to interpret them.  The institutional review board approved the prospective study of the seminar conversion, which was performed after the end of the winter semester 2015/2016. Didactically, this included a course split into online preparation, attendance phase and online follow-up with integration of interactive scaffolding, practice-oriented clinical teaching according to Stanford, Peyton skills transfer and extensive feedback into the attendance phase. At the beginning and at the end of each course, each student filled in identical, standardized questionnaires (n = 256 before and after conversion) using a 5-point Likert scale (1: very good; to 5: deficient) and additionally answered two randomly chosen written examination questions from a content-adapted questionnaire pool of the last five years. For statistical evaluation, the Mann-Whitney U-Test was used for evaluation data and Fisher's Exact test for exam questions.  Before/after conversion, the subjective total evaluation score of students was 3.22 (mean value) ± 1.51 (standard deviation) / 1.66 ± 0.78 (p < 0.001) and the objective proportion of correctly answered examination questions in the respective cohort at the beginning of the seminar 37.7/53.9 % and at the end of the seminar 55.1/84.6 % (p < 0.001).  The conversion of the test seminar resulted in both a better evaluation of the teaching unit by the students (evaluation) and a considerably higher rate of correctly answered examination questions from past state examinations (learning success). This supports transferring the concept to comparable teaching units.   · Radiological teaching allows integration of current learning theory concepts with reasonable effort.. · In a test seminar this improved the evaluation results of the teaching unit by the students.. · In addition, this also led to a higher rate of correctly answered examination questions from past state examinations.. · This supports further steps towards excellent radiological teaching.. · Wirth S, William Y, Paolini M et al. Improvement of Radiological Teaching - Effects of Focusing of Learning Targets and Increased Consideration of Learning Theory Knowledge. Fortschr Röntgenstr 2018; 190: 161 - 174. © Georg Thieme Verlag KG Stuttgart · New York.

The use of food in chemistry experiments to engage and enrich the teaching in the classroom

NASA Astrophysics Data System (ADS)

Topping, Brian Michael

Students often gain more knowledge out of hands on work. Labs and demonstrations increase knowledge often more than the book work and notes because they motivate interest and provide real world application. In an effort to incorporate labs into chemistry I have developed a unit centered on food in order to teach a variety of concepts and lab techniques to high school students. The study of food can be a tremendous motivator and help students take interest and ownership in the learning process. The unit was evaluated for its effectiveness through the use of a pre and post-test assessments as well as a post survey of students' attitudes towards labs and learning science. This study showed that students' overall conceptual knowledge of the various topics related to food increased as a result of this unit with evidence provided by the post-test scores.

Test effectiveness study report: An analytical study of system test effectiveness and reliability growth of three commercial spacecraft programs

NASA Technical Reports Server (NTRS)

Feldstein, J. F.

1977-01-01

Failure data from 16 commercial spacecraft were analyzed to evaluate failure trends, reliability growth, and effectiveness of tests. It was shown that the test programs were highly effective in ensuring a high level of in-orbit reliability. There was only a single catastrophic problem in 44 years of in-orbit operation on 12 spacecraft. The results also indicate that in-orbit failure rates are highly correlated with unit and systems test failure rates. The data suggest that test effectiveness estimates can be used to guide the content of a test program to ensure that in-orbit reliability goals are achieved.

Corrective Action Investigation Plan for Corrective Action Unit 140: Waste Dumps, Burn Pits, and Storage Area, Nevada Test Site, Nevada, July 2002, Rev. No. 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

NNSA /NV

This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office's approach to collect the data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit (CAU) 140 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 140 consists of nine Corrective Action Sites (CASs): 05-08-01, Detonation Pits; 05-08-02, Debris Pits; 05-17-01, Hazardous Waste Accumulation Site (Buried); 05-19-01, Waste Disposal Site; 05-23-01, Gravel Gertie; 05-35-01, Burn Pit; 05-99-04, Burn Pit; 22-99-04, Radioactive Waste Dump; 23-17-01, Hazardous Waste Storage Area. All nine of these CASs are located withinmore » Areas 5, 22, and 23 of the Nevada Test Site (NTS) in Nevada, approximately 65 miles northwest of Las Vegas. This CAU is being investigated because disposed waste may be present without appropriate controls (i.e., use restrictions, adequate cover) and hazardous and/or radioactive constituents may be present or migrating at concentrations and locations that could potentially pose a threat to human health and the environment. The NTS has been used for various research and development projects including nuclear weapons testing. The CASs in CAU 140 were used for testing, material storage, waste storage, and waste disposal. A two-phase approach has been selected to collect information and generate data to satisfy needed resolution criteria and resolve the decision statements. Phase I will determine if contaminants of potential concern (COPCs) are present in concentrations exceeding preliminary action levels. This data will be evaluated at all CASs. Phase II will determine the extent of the contaminant(s) of concern (COCs). This data will only be evaluated for CASs with a COC identified during Phase I. Based on process knowledge, the COPCs for CAU 140 include volatile organics, semivolatile organics, petroleum hydrocarbons, explosive residues, herbicides, pesticides, polychlorinated biphenyls, metals, and radionuclides. The results of this field investigation will support a defensible evaluation of corrective action alternatives in the corrective action decision document.« less

Tomato seeds maturity detection system based on chlorophyll fluorescence

NASA Astrophysics Data System (ADS)

Li, Cuiling; Wang, Xiu; Meng, Zhijun

2016-10-01

Chlorophyll fluorescence intensity can be used as seed maturity and quality evaluation indicator. Chlorophyll fluorescence intensity of seed coats is tested to judge the level of chlorophyll content in seeds, and further to judge the maturity and quality of seeds. This research developed a detection system of tomato seeds maturity based on chlorophyll fluorescence spectrum technology, the system included an excitation light source unit, a fluorescent signal acquisition unit and a data processing unit. The excitation light source unit consisted of two high power LEDs, two radiators and two constant current power supplies, and it was designed to excite chlorophyll fluorescence of tomato seeds. The fluorescent signal acquisition unit was made up of a fluorescence spectrometer, an optical fiber, an optical fiber scaffolds and a narrowband filter. The data processing unit mainly included a computer. Tomato fruits of green ripe stage, discoloration stage, firm ripe stage and full ripe stage were harvested, and their seeds were collected directly. In this research, the developed tomato seeds maturity testing system was used to collect fluorescence spectrums of tomato seeds of different maturities. Principal component analysis (PCA) method was utilized to reduce the dimension of spectral data and extract principal components, and PCA was combined with linear discriminant analysis (LDA) to establish discriminant model of tomato seeds maturity, the discriminant accuracy was greater than 90%. Research results show that using chlorophyll fluorescence spectrum technology is feasible for seeds maturity detection, and the developed tomato seeds maturity testing system has high detection accuracy.

Wear resistance of machine tools' bionic linear rolling guides by laser cladding

NASA Astrophysics Data System (ADS)

Wang, Yiqiang; Liu, Botao; Guo, Zhengcai

2017-06-01

In order to improve the rolling wear resistance (RWR) of linear rolling guides (LRG) as well as prolong the life of machine tools, various shape samples with different units spaces ranged from 1 to 5 mm are designed through the observation of animals in the desert and manufactured by laser cladding. Wear resistance tests reproducing closely the real operational condition are conducted by using a homemade linear reciprocating wear test machine, and wear resistance is evaluated by means of weight loss measurement. Results indicate that the samples with bionic units have better RWR than the untreated one, of which the reticulate treated sample with unit space 3 mm present the best RWR. More specifically, among the punctuate treated samples, the mass loss increases with the increase of unit space; among the striate treated samples, the mass loss changes slightly with the increase of unit space, attaining a minimum at the unit space of 4 mm; among the reticulate treated samples, with the increase of unit space, the mass loss initially decreases, but turns to increase after reaching a minimum at the unit space of 3 mm. Additionally, the samples with striate shape perform better wear resistance than the other shape groups on the whole. From the ratio value of laser treated area to contacted area perspective, that the samples with ratio value between 0.15 and 0.3 possess better wear resistance is concluded.

Methods and instruments for materials testing

NASA Technical Reports Server (NTRS)

Hansma, Paul (Inventor); Drake, Barney (Inventor); Rehn, Douglas (Inventor); Adams, Jonathan (Inventor); Lulejian, Jason (Inventor)

2011-01-01

Methods and instruments for characterizing a material, such as the properties of bone in a living human subject, using a test probe constructed for insertion into the material and a reference probe aligned with the test probe in a housing. The housing is hand held or placed so that the reference probe contacts the surface of the material under pressure applied either by hand or by the weight of the housing. The test probe is inserted into the material to indent the material while maintaining the reference probe substantially under the hand pressure or weight of the housing allowing evaluation of a property of the material related to indentation of the material by the probe. Force can be generated by a voice coil in a magnet structure to the end of which the test probe is connected and supported in the magnet structure by a flexure, opposing flexures, a linear translation stage, or a linear bearing. Optionally, a measurement unit containing the test probe and reference probe is connected to a base unit with a wireless connection, allowing in the field material testing.

An Electromagnetic/Capacitive Composite Sensor for Testing of Thermal Barrier Coatings

PubMed Central

Ren, Yuan; Pan, Mengchun; Chen, Dixiang; Tian, Wugang

2018-01-01

Thermal barrier coatings (TBCs) can significantly reduce the operating temperature of the aeroengine turbine blade substrate, and their testing technology is very urgently demanded. Due to their complex multi-layer structure, it is hard to evaluate TBCs with a single function sensor. In this paper, an electromagnetic/capacitive composite sensor is proposed for the testing of thermal barrier coatings. The dielectric material is tested with planar capacitor, and the metallic material is tested with electromagnetic coils. Then, the comprehensive test and evaluation of thermal barrier coating system can be realized. The sensor is optimized by means of theoretical and simulation analysis, and the interaction between the planar capacitor and the electromagnetic coil is studied. The experimental system is built based on an impedance analyser and multiplex unit to evaluate the performance of the composite sensor. The transimpedances and capacitances are measured under different coating parameters, such as thickness and permittivity of top coating as well as bond layer conductivity. The experimental results agree with the simulation analysis, and the feasibility of the sensor is proved. PMID:29783746

Testing low cost anaerobic digestion (AD) systems

USDA-ARS?s Scientific Manuscript database

To evaluate the potential for low technology and low cost digesters for small dairies, BARC and researchers from the University of Maryland installed six modified Taiwanese-model field-scale (FS) digesters near the original dairy manure digester. The FS units receive the same post-separated liquid ...

INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

EPA Science Inventory

Bench scale laboratory studies and pilot scale studies in a simulated field-test situation were performed to evaluate the integration of gas-solid ultaviolet (UV) photocatalytic oxidation (PCO) downstream if an air stripper unit as a technology for cost-effectively treating water...

Evaluating Workplace English Language Programs

ERIC Educational Resources Information Center

Ekkens, Kristin; Winke, Paula

2009-01-01

Companies across the United States provide workplace English classes to non-native-English-speaking employees to increase productivity, retention, and on-the-job safety. Institutions that financially support the programs often require evidence of learning through standardized tests as a prerequisite for continued funding. However, the tests…

Developing intelligent transportation systems using the national ITS archetecture: an executive edition for senior transportation managers

DOT National Transportation Integrated Search

2012-07-01

This report presents the Cost Benefit Analysis Test Plan for the national evaluation of the Los Angeles County Congestion Reduction Demonstration (LAC CRD) under the United States Department of Transportation (U.S. DOT) Congestion Reduction Demonstra...

1995 Truck Size and Weight Performance-Based Workshop report : activity 5 : document North American and European experiences

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Evaluation of novophalt as an additive in asphalt.

DOT National Transportation Integrated Search

1991-01-01

Novophalt, which is an ethylene vinyl acetate polymer, was used as an asphalt additive in a test section in an attempt to determine whether it is useful in the prevention of rutting. A special blending unit was required to blend the asphalt cement an...

EVALUATION OF A DNA PROBE TEST KIT FOR DETECTION OF SALMONELLAE IN BIOSOLIDS

EPA Science Inventory

Aims: Current United States regulations (40 CFR 503) for "Class A" biosolids requires use of multiple-tube fermentation techniques for fecal coliform or multiple tube enrichment techniques for Salmonella spp. followed by isolation and biochemical and serological confirmation. T...

Genetic diversity of Hepatozoon spp. in coyotes from the south-central United States.

PubMed

Starkey, Lindsay A; Panciera, Roger J; Paras, Kelsey; Allen, Kelly E; Reiskind, Michael H; Reichard, Mason V; Johnson, Eileen M; Little, Susan E

2013-04-01

To better define the strains and species of Hepatozoon that infect coyotes in the south-central United States, whole blood and muscle samples were collected from 44 coyotes from 6 locations in Oklahoma and Texas. Samples were evaluated by a nested polymerase chain reaction (PCR) using primers amplifying a variable region of the apicomplexan 18S rRNA gene as well as histopathology (muscle only) for presence of tissue cysts. Hepatozoon spp. infections were identified in 79.5% (35/44) of coyotes tested including 27 of 44 (61.4%) whole blood samples and 17 of 44 (38.6%) muscle samples tested by PCR and 23 of 44 (52.3%) muscle samples evaluated by histological examination. Analysis revealed 19 distinct sequences comprising 3 major clusters of Hepatozoon spp., i.e., 1 most closely related to Hepatozoon americanum, another most closely related to Hepatozoon canis , and the third an intermediate between the 2 groups. The diversity of Hepatozoon spp. in wild canids appears greater than previously recognized and warrants further investigation.

Geology and ground-water resources of the Two Medicine unit and adjacent areas, Blackfeet Indian Reservation, Montana, with a section on chemical quality of water

USGS Publications Warehouse

Paulson, Q.F.; Zimmerman, Tom V.; Langford, Russell H.

1965-01-01

The Two Medicine Irrigation Unit, on the Blackfeet Indian Reservation of northern Montana, is irrigated by water diverted from Two Medicine Creek. Waterlogging because of overapplication of water and locally inadequate subsurface drainage is a serious problem. This study was undertaken by the U.S. Geological Survey in cooperation with the U.S. Bureau of Indian Affairs to evaluate the problem and to suggest remedies. For this study, the geology was mapped, and data concerning 129 wells and test holes were gathered. The water level in 63 wells was measured periodically. Three test holes were drilled and 4 single-well and 1 multiple-well pump tests were made. Nineteen samples of ground water were collected and analyzed chemically, and applied irrigation water was analyzed periodically.

INTERIM REPORT ON THE EVOLUTION AND ...

EPA Pesticide Factsheets

A demonstration of screening technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under the U.S. Environmental Protection Agency's(EPA's) Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in 2004. The objectives of the demonstration included evaluating each participating technology's accuracy, precision, sensitivity, sample throughput, tendency for matrix effects, and cost. The test also included an assessment of how well the technology's results compared to those generated by established laboratory methods using high-resolution mass spectrometry (HRMS). The demonstration objectives were accomplished by evaluating the results generated by each technology from 209 soil, sediment, and extract samples. The test samples included performance evaluation (PE) samples (i.e., contaminant concentrations were certified or the samples were spiked with known contaminants) and environmental samples collected from 10 different sampling locations. The PE and environmental samples were distributed to the technology developers in blind, random order. One of the participants in the original SITE demonstration was Hybrizyme Corporation, which demonstrated the use of the AhRC PCR Kit. The AhRC PCR Kit was a technology that reported the concentration of aryl hydrocarbon receptor (AhR) binding compounds in a sample, with units reported as Ah Receptor Binding Units (AhRBU). At the time of the original dem

LED Curing Lights and Temperature Changes in Different Tooth Sites

PubMed Central

Armellin, E.; Bovesecchi, G.; Coppa, P.; Pasquantonio, G.; Cerroni, L.

2016-01-01

Objectives. The aim of this in vitro study was to assess thermal changes on tooth tissues during light exposure using two different LED curing units. The hypothesis was that no temperature increase could be detected within the dental pulp during polymerization irrespective of the use of a composite resin or a light-curing unit. Methods. Caries-free human first molars were selected, pulp residues were removed after root resection, and four calibrated type-J thermocouples were positioned. Two LED lamps were tested; temperature measurements were made on intact teeth and on the same tooth during curing of composite restorations. The data was analyzed by one-way analysis of variance (ANOVA), Wilcoxon test, Kruskal-Wallis test, and Pearson's χ 2. After ANOVA, the Bonferroni multiple comparison test was performed. Results. Polymerization data analysis showed that in the pulp chamber temperature increase was higher than that without resin. Starlight PRO, in the same condition of Valo lamp, showed a lower temperature increase in pre- and intrapolymerization. A control group (without composite resin) was evaluated. Significance. Temperature increase during resin curing is a function of the rate of polymerization, due to the exothermic polymerization reaction, the energy from the light unit, and time of exposure. PMID:27195282

LED Curing Lights and Temperature Changes in Different Tooth Sites.

PubMed

Armellin, E; Bovesecchi, G; Coppa, P; Pasquantonio, G; Cerroni, L

2016-01-01

Objectives. The aim of this in vitro study was to assess thermal changes on tooth tissues during light exposure using two different LED curing units. The hypothesis was that no temperature increase could be detected within the dental pulp during polymerization irrespective of the use of a composite resin or a light-curing unit. Methods. Caries-free human first molars were selected, pulp residues were removed after root resection, and four calibrated type-J thermocouples were positioned. Two LED lamps were tested; temperature measurements were made on intact teeth and on the same tooth during curing of composite restorations. The data was analyzed by one-way analysis of variance (ANOVA), Wilcoxon test, Kruskal-Wallis test, and Pearson's χ (2). After ANOVA, the Bonferroni multiple comparison test was performed. Results. Polymerization data analysis showed that in the pulp chamber temperature increase was higher than that without resin. Starlight PRO, in the same condition of Valo lamp, showed a lower temperature increase in pre- and intrapolymerization. A control group (without composite resin) was evaluated. Significance. Temperature increase during resin curing is a function of the rate of polymerization, due to the exothermic polymerization reaction, the energy from the light unit, and time of exposure.

Green Propulsion Auxiliary Power Unit Demonstration at MSFC

NASA Technical Reports Server (NTRS)

Robinson, Joel W.

2014-01-01

In 2012, the National Aeronautics & Space Administration (NASA) Space Technology Mission Directorate (STMD) began the process of building an integrated technology roadmap, including both technology pull and technology push strategies. Technology Area 1 (TA-01)1 for Launch Propulsion Systems is one of fourteen TAs that provide recommendations for the overall technology investment strategy and prioritization of NASA's space technology activities. Identified within TA-01 was the need for a green propulsion auxiliary power unit (APU) for hydraulic power by 2015. Engineers led by the author at the Marshall Space Flight Center (MSFC) have been evaluating green propellant alternatives and have begun the development of an APU test bed to demonstrate the feasibility of use. NASA has residual APU assets remaining from the retired Space Shuttle Program. Likewise, the F-16 Falcon fighter jet also uses an Emergency Power Unit (EPU) that has similar characteristics to the NASA hardware. Both EPU and APU components have been acquired for testing at MSFC. This paper will summarize the status of the testing efforts of green propellant from the Air Force Research Laboratory (AFRL) propellant AFM315E based on hydroxyl ammonium nitrate (HAN) with these test assets.

22st Annual National Test and Evaluation Conference

DTIC Science & Technology

2006-03-09

B1 B2 y ii) Factor B affects the standard deviation C2 C1 y iii) Factor C affects the average and the standard deviation D1 = D2 y iv) Factor D has...22303 UNITED STATES (P) (703)862-0908 (F) (703)970-5700 poole_grady@emc.com Mr. Josh Pressnell RTI 8306 Rugby Rd. Manassas, VA 20111...Ricciardi RTI 8306 Rugby Rd. Manassas, VA 20111-1912 UNITED STATES (P) (703)365-9662 (F) (703)365-9818 michael.ricciardi@rti-world.com Mr

At-Sea Test and Evaluation Of Oxygen (O2) Analyzers.

DTIC Science & Technology

1981-04-01

Paramagnetic Oxygen Analyzer 2-6 2.4 Thermomagnetic Oxygen Analyzer Sensor 2-8 2.5 Cell Voltage versus Oxygen Concentration at 2-11 Various Cell ...of flue gas out of the stack across the cell and back into the stack. In-situ units place the cell directly in the flue gas path in the uptake. ) The...repetitive failurc of a cell heater temperature control circuit and a control cabinet electron- ic malfunction. Of the five (5) units that remained in

Vacuum Head Checks Foam/Substrate Bonds

NASA Technical Reports Server (NTRS)

Lloyd, James F.

1989-01-01

Electromechanical inspection system quickly gives measurements indicating adhesion, or lack thereof, between rigid polyurethane foam and aluminum substrate. Does not damage inspected article, easy to operate, and used to perform "go/no-go" evaluations or as supplement to conventional destructive pull-plug testing. Applies vacuum to small area of foam panel and measures distance through which foam pulled into vacuum. Probe head applied to specimen and evacuated through hose to controller/monitor unit. Digital voltmeter in unit reads deflection of LVDT probe head.

Operational Based Vision Assessment Research: Depth Perception

DTIC Science & Technology

2014-11-01

13-072 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) USAF School of Aerospace Medicine...Aeromedical Research Department 2510 Fifth St. Wright-Patterson AFB, OH 45433-7913 8. PERFORMING ORGANIZATION REPORT NUMBER AFRL-SA-WP-JA-2014...tests are tests of stereopsis, such as the AFVT and AO Vectograph. Others evaluate depth perception with stereo as a contributor to performance , such

Hybrid poplar grows poorly on acid spoil banks at high elevations in West Virginia

Treesearch

George R., Jr. Trimble

1963-01-01

In the early 1950s, a region-wide series of hybrid poplar clonal tests was begun in the Northeast to evaluate the performance of 50 selected clones under a variety of site and climatic conditions. The basic test unit was a block of 50 randomized plots-1 plot for each of the 50 clones. In each plot, 16 cuttings were planted at 4-foot spacing.

CDRA-4EU Testing to Assess Increased Number of ISS Crew

NASA Technical Reports Server (NTRS)

Peters, Warren T.; Knox, James C.

2017-01-01

The International Space Station (ISS) program is investigating methods to increase carbon dioxide (CO2) removal on ISS in order to support an increased number of astronauts at a future date. The Carbon Dioxide Removal Assembly - Engineering Unit (CDRA-4EU) system at NASA Marshall Space Flight Center (MSFC) was tested at maximum fan settings to evaluate CO2 removal rate and power consumption at those settings.

North Carolina Linking Study: A Study of the Alignment of the NWEA RIT Scale with the North Carolina State End of Grade (EOG) Testing Program

ERIC Educational Resources Information Center

Northwest Evaluation Association, 2014

2014-01-01

Recently, the Northwest Evaluation Association (NWEA) completed a study to connect the scale of the North Carolina State End of Grade (EOG) Testing Program used for North Carolina's mathematics and reading assessments with NWEA's Rausch Interval Unit (RIT) scale. Information from the state assessments was used in a study to establish…

Readability and Test-Retest Reliability of a Psychometric Instrument Designed to Assess HIV/AIDS Attitudes, Beliefs, Behaviours and Sources of HIV Prevention Information of Young Adults

ERIC Educational Resources Information Center

Balogun, Joseph; Abiona, Titilayo; Lukobo-Durrell, Mainza; Adefuye, Adedeji; Amosun, Seyi; Frantz, Jose; Yakut, Yavuz

2011-01-01

Objective: This comparative study evaluated the readability and test-retest reliability of a questionnaire designed to assess the attitudes, beliefs behaviours and sources of information about HIV/AIDS among young adults recruited from universities in the United States of America (USA), Turkey and South Africa. Design/Setting: The instrument was…

Evaluation Transportability Testing of the Joint Modular Intermodal Platform (JMIP) Unit #4, TP-94-01, Transportability Testing Procedures

DTIC Science & Technology

2007-07-01

447 3893 VSN: NL1FR5 MFG Serial #: T-018447EFJM Weight: 19,340 lbs 3-1 5. Semitrailer, flatbed , breakbulk/container transporter, 22.5 ton Model...CHAFTING PIECE, 118" X 6" X 40" PLYWOOD, (I REaD). LAMINATE TO BEARING PIECE W16-6d NAILS EVENLY SPACED. SIDE STRAPPING BOARD ASSEMBLY (2 REOD) (I

Site characterization at the Rabbit Valley Geophysical Performance Evaluation Range

NASA Astrophysics Data System (ADS)

Koppenjan, S.,; Martinez, M.

The United States Department of Energy (US DOE) is developing a Geophysical Performance Evaluation Range (GPER) at Rabbit Valley located 30 miles west of Grand Junction, Colorado. The purpose of the range is to provide a test area for geophysical instruments and survey procedures. Assessment of equipment accuracy and resolution is accomplished through the use of static and dynamic physical models. These models include targets with fixed configurations and targets that can be re-configured to simulate specific specifications. Initial testing (1991) combined with the current tests at the Rabbit Valley GPER will establish baseline data and will provide performance criteria for the development of geophysical technologies and techniques. The US DOE's Special Technologies Laboratory (STL) staff has conducted a Ground Penetrating Radar (GPR) survey of the site with its stepped FM-CW GPR. Additionally, STL contracted several other geophysical tests. These include an airborne GPR survey incorporating a 'chirped' FM-CW GPR system and a magnetic survey with a surfaced-towed magnetometer array unit Ground-based and aerial video and still frame pictures were also acquired. STL compiled and analyzed all of the geophysical maps and created a site characterization database. This paper discusses the results of the multi-sensor geophysical studies performed at Rabbit Valley and the future plans for the site.

Site characterization at the Rabbit Valley Geophysical Performance Evaluation Range

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koppenjan, S,; Martinez, M.

1994-06-01

The United States Department of Energy (US DOE) is developing a Geophysical Performance Evaluation Range (GPER) at Rabbit Valley located 30 miles west of Grand Junction, Colorado. The purpose of the range is to provide a test area for geophysical instruments and survey procedures. Assessment of equipment accuracy and resolution is accomplished through the use of static and dynamic physical models. These models include targets with fixed configurations and targets that can be re-configured to simulate specific specifications. Initial testing (1991) combined with the current tests at the Rabbit Valley GPER will establish baseline data and will provide performance criteriamore » for the development of geophysical technologies and techniques. The US DOE`s Special Technologies Laboratory (STL) staff has conducted a Ground Penetrating Radar (GPR) survey of the site with its stepped FM-CW GPR. Additionally, STL contracted several other geophysical tests. These include an airborne GPR survey incorporating a ``chirped`` FM-CW GPR system and a magnetic survey with a surfaced-towed magnetometer array unit Ground-based and aerial video and still frame pictures were also acquired. STL compiled and analyzed all of the geophysical maps and created a site characterization database. This paper discusses the results of the multi-sensor geophysical studies performed at Rabbit Valley and the future plans for the site.« less

Field testing of a next generation pointer/tracker for IRCM

NASA Astrophysics Data System (ADS)

Chapman, Stuart; Wildgoose, Iain; McDonald, Eric; Duncan, Stuart

2008-10-01

SELEX Galileo has been involved in the development, manufacture and support of high performance electro-optic pointing and stabilisation systems for over forty years. The Company currently supplies the pointer/trackers for the AN/AAQ-24(V) NEMESIS DIRCM system, for which over 1,000 combat-proven units have been produced and deployed in the US, the UK and other nations. In 2007, SELEX Galileo embarked on an internally funded programme to develop ECLIPSE, a new advanced, lightweight, low-cost IRCM pointer/tracker, exploiting the extensive knowledge and experience gained from previous targeting and IRCM programmes. The ECLIPSE design is centred on a low inertia, two-axis servo mechanism with a strap-down inertial sensor and advanced sightline control algorithms, allowing effective tracking through the nadir and providing superior sightline performance. The programme involved the production of three demonstrator units in 2007, and two pre-production units in 2008. The demonstrator units were first trialled as part of a NEMESIS DIRCM system in late 2007, and in April 2008 100% success was achieved in jamming live-fire demonstrations. Helicopter installation and ground testing of a UK only trials system is complete, initial flight testing has just begun, and the airborne test and evaluation scheduled for late summer 2008 will bring the ECLIPSE System to technology readiness to level 7 (TRL7). This paper describes the Eclipse performance demonstrated to date.

The adenosine triphosphate test is a rapid and reliable audit tool to assess manual cleaning adequacy of flexible endoscope channels.

PubMed

Alfa, Michelle J; Fatima, Iram; Olson, Nancy

2013-03-01

The study objective was to verify that the adenosine triphosphate (ATP) benchmark of <200 relative light units (RLUs) was achievable in a busy endoscopy clinic that followed the manufacturer's manual cleaning instructions. All channels from patient-used colonoscopes (20) and duodenoscopes (20) in a tertiary care hospital endoscopy clinic were sampled after manual cleaning and tested for residual ATP. The ATP test benchmark for adequate manual cleaning was set at <200 RLUs. The benchmark for protein was <6.4 μg/cm(2), and, for bioburden, it was <4-log10 colony-forming units/cm(2). Our data demonstrated that 96% (115/120) of channels from 20 colonoscopes and 20 duodenoscopes evaluated met the ATP benchmark of <200 RLUs. The 5 channels that exceeded 200 RLUs were all elevator guide-wire channels. All 120 of the manually cleaned endoscopes tested had protein and bioburden levels that were compliant with accepted benchmarks for manual cleaning for suction-biopsy, air-water, and auxiliary water channels. Our data confirmed that, by following the endoscope manufacturer's manual cleaning recommendations, 96% of channels in gastrointestinal endoscopes would have <200 RLUs for the ATP test kit evaluated and would meet the accepted clean benchmarks for protein and bioburden. Copyright © 2013 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Establishing daily quality control (QC) in screen-film mammography using leeds tor (max) phantom at the breast imaging unit of USTH-Benavides Cancer Institute

NASA Astrophysics Data System (ADS)

Acaba, K. J. C.; Cinco, L. D.; Melchor, J. N.

2016-03-01

Daily QC tests performed on screen film mammography (SFM) equipment are essential to ensure that both SFM unit and film processor are working in a consistent manner. The Breast Imaging Unit of USTH-Benavides Cancer Institute has been conducting QC following the test protocols in the IAEA Human Health Series No.2 manual. However, the availability of Leeds breast phantom (CRP E13039) in the facility made the task easier. Instead of carrying out separate tests on AEC constancy and light sensitometry, only one exposure of the phantom is done to accomplish the two tests. It was observed that measurements made on mAs output and optical densities (ODs) using the Leeds TOR (MAX) phantom are comparable with that obtained from the usual conduct of tests, taking into account the attenuation characteristic of the phantom. Image quality parameters such as low contrast and high contrast details were also evaluated from the phantom image. The authors recognize the usefulness of the phantom in determining technical factors that will help improve detection of smallest pathological details on breast images. The phantom is also convenient for daily QC monitoring and economical since less number of films is expended.

In vitro assessment of polymerization procedures in Class II restorations: sealing, FTIR, and microhardness evaluations.

PubMed

Tassery, H; de Donato, P; Barrès, O; Déjou, J

2001-01-01

This study was undertaken to evaluate several polymerization and filling procedures (incremental, bulk, light-tip, soft-cured, plasma devices) in Class II restorations through (1) a sealing evaluation of restorations filled with Tetric Ceram (TC) and Bisfil 2B (B2B, self-cured composite used as a control), (2) a FTIR analysis measuring the variations of the degree of conversion in terms of area unit ratio of the relevant resin composites and (3) a microhardness test to corroborate the FTIR analysis. The length of the tracer penetration was measured from the gingival margin up to the cavity wall with an episcope on sectioned teeth. A ceramic mould, simulating a Class II, was filled according to the different groups and the samples were analyzed with a Bruker IFS 55 spectrometer on ultrathin sections (3 mu). The results were analyzed in terms of area unit ratio and total exposed energy. Under the same conditions, a microhardness test was run with a Frank Weihem machine. The results of the sealing evaluation for light-tip, incremental and self-cured techniques did not differ. The plasma procedure failed in this evaluation as the bottom increment was not polymerized. The smallest area unit ratio (the best degree of conversion) was observed in 2 groups: one, the combination of the light-tip and soft process, and two, the self-cured resin composite (B2B). The distance at which the plasma procedure failed to cure the resin composite was between 3.5 and 4.5 mm. The microhardness test confirmed the FTIR analysis except for the group G2 (TC + light-tip). As also shown by FTIR analysis, no difference between the two relevant levels was observed with the hardness test. The dentin marginal sealing efficiency of Tetric Ceram restorations was increased with the light-tip technique, but was not better than the self-cured resin composite (B2B). For Tetric Ceram, the combination of the light-tip and soft process leads to a higher degree of conversion than the other groups. There is no linear relationship between the degree of conversion, the microhardness and the total exposed energy. The combination of the soft polymerization and the light-tip device might be an alternative restorative technique to the current incremental technique.

Evaluating the efficiency of nuclear energy policies: an empirical examination for 26 countries.

PubMed

Gozgor, Giray; Demir, Ender

2017-08-01

The decarbonization of the global economy is an urgent concern. As a potential solution, it can be important to understand the efficiency of nuclear energy policies. For this purpose, the paper analyzes whether there is a unit root in nuclear energy consumption in 26 countries and it uses the unit root tests with two endogenous (unknown) structural breaks. The paper finds that nuclear energy consumption is stationary around a level and the time trend in 25 of 26 countries and nuclear energy consumption contains a unit root only in France. The paper also discusses the potential implications of the findings.

Impact of improving vehicle front design on the burden of pedestrian injuries in Germany, the United States, and India.

PubMed

Moran, Dane; Bose, Dipan; Bhalla, Kavi

2017-11-17

European car design regulations and New Car Assessment Program (NCAP) ratings have led to reductions in pedestrian injuries. The aim of this study was to evaluate the impact of improving vehicle front design on mortality and morbidity due to pedestrian injuries in a European country (Germany) and 2 countries (the United States and India) that do not have pedestrian-focused NCAP testing or design regulations. We used data from the International Road Traffic and Accident Database and the Global Burden of Disease project to estimate baseline pedestrian deaths and nonfatal injuries in each country in 2013. The effect of improved passenger car star ratings on probability of pedestrian injury was based on recent evaluations of pedestrian crash data from Germany. The effect of improved heavy motor vehicle (HMV) front end design on pedestrian injuries was based on estimates reported by simulation studies. We used burden of disease methods to estimate population health loss by combining the burden of morbidity and mortality in disability-adjusted life years (DALYs) lost. Extrapolating from evaluations in Germany suggests that improving front end design of cars can potentially reduce the burden of pedestrian injuries due to cars by up to 24% in the United States and 41% in India. In Germany, where cars comply with the United Nations regulation on pedestrian safety, additional improvements would have led to a 1% reduction. Similarly, improved HMV design would reduce DALYs lost by pedestrian victims hit by HMVs by 20% in each country. Overall, improved vehicle design would reduce DALYs lost to road traffic injuries (RTIs) by 0.8% in Germany, 4.1% in the United States, and 6.7% in India. Recent evaluations show a strong correlation between Euro NCAP pedestrian scores and real-life pedestrian injuries, suggesting that improved car front end design in Europe has led to substantial reductions in pedestrian injuries. Although the United States has fewer pedestrian crashes, it would nevertheless benefit substantially by adopting similar regulations and instituting pedestrian NCAP testing. The maximum benefit would be realized in low- and middle-income countries like India that have a high proportion of pedestrian crashes. Though crash avoidance technologies are being developed to protect pedestrians, supplemental protection through design regulations may significantly improve injury countermeasures for vulnerable road users.

Reducing Uncertainty in the Distribution of Hydrogeologic Units within Volcanic Composite Units of Pahute Mesa Using High-Resolution 3-D Resistivity Methods, Nevada Test Site, Nevada

USGS Publications Warehouse

Rodriguez, Brian D.; Sweetkind, Don; Burton, Bethany L.

2010-01-01

The U.S. Department of Energy (DOE) and the National Nuclear Security Administration (NNSA) at their Nevada Site Office (NSO) are addressing groundwater contamination resulting from historical underground nuclear testing through the Environmental Management program and, in particular, the Underground Test Area (UGTA) project. From 1951 to 1992, 828 underground nuclear tests were conducted at the Nevada Test Site (NTS) northwest of Las Vegas (DOE UGTA, 2003). Most of these tests were conducted hundreds of feet above the groundwater table; however, more than 200 of the tests were near, or within, the water table. This underground testing was limited to specific areas of the NTS including Pahute Mesa, Rainier Mesa/Shoshone Mountain, Frenchman Flat, and Yucca Flat. Volcanic composite units make up much of the area within the Pahute Mesa Corrective Action Unit (CAU) at the NTS, Nevada. The extent of many of these volcanic composite units extends throughout and south of the primary areas of past underground testing at Pahute and Rainier Mesas. As situated, these units likely influence the rate and direction of groundwater flow and radionuclide transport. Currently, these units are poorly resolved in terms of their hydrologic properties introducing large uncertainties into current CAU-scale flow and transport models. In 2007, the U.S. Geological Survey (USGS), in cooperation with DOE and NNSA-NSO acquired three-dimensional (3-D) tensor magnetotelluric data at the NTS in Area 20 of Pahute Mesa CAU. A total of 20 magnetotelluric recording stations were established at about 600-m spacing on a 3-D array and were tied to ER20-6 well and other nearby well control (fig. 1). The purpose of this survey was to determine if closely spaced 3-D resistivity measurements can be used to characterize the distribution of shallow (600- to 1,500-m-depth range) devitrified rhyolite lava-flow aquifers (LFA) and zeolitic tuff confining units (TCU) in areas of limited drill hole control on Pahute Mesa within the Calico Hills zeolitic volcanic composite unit (VCU), an important hydrostratigraphic unit in Area 20. The resistivity response was evaluated and compared with existing well data and hydrogeologic unit tops from the current Pahute Mesa framework model. In 2008, the USGS processed and inverted the magnetotelluric data into a 3-D resistivity model. We interpreted nine depth slices and four west-east profile cross sections of the 3-D resistivity inversion model. This report documents the geologic interpretation of the 3-D resistivity model. Expectations are that spatial variations in the electrical properties of the Calico Hills zeolitic VCU can be detected and mapped with 3-D resistivity, and that these changes correlate to differences in rock permeability. With regard to LFA and TCU, electrical resistivity and permeability are typically related. Tuff confining units will typically have low electrical resistivity and low permeability, whereas LFA will have higher electrical resistivity and zones of higher fracture-related permeability. If expectations are shown to be correct, the method can be utilized by the UGTA scientists to refine the hydrostratigraphic unit (HSU) framework in an effort to more accurately predict radionuclide transport away from test areas on Pahute and Rainier Mesas.

Gas-fired duplex free-piston Stirling refrigerator

NASA Astrophysics Data System (ADS)

Urieli, L.

1984-03-01

The duplex free-piston Stirling refrigerator is a potentially high efficiency, high reliability device which is ideally suited to the home appliance field, in particular as a gas-fired refrigerator. It has significant advantages over other equivalent devices including freedom from halogenated hydrocarbons, extremely low temperatures available at a high efficiency, integrated water heating, and simple burner system control. The design and development of a portable working demonstration gas-fired duplex Stirling refrigeration unit is described. A unique combination of computer aided development and experimental development was used, enabling a continued interaction between the theoretical analysis and practical testing and evaluation. A universal test rig was developed in order to separately test and evaluate major subunits, enabling a smooth system integration phase.

Body image and HIV risk among college students.

PubMed

Gillen, Meghan M; Markey, Charlotte N

2014-11-01

To focus on the role of sex, race/ethnicity, and body image in HIV-protective behaviors. Undergraduates (N = 277; 53% women; M = 19.27 years old) from the United States completed a survey on HIV-related behaviors and body image (appearance orientation and appearance evaluation). Women and African Americans/ Blacks were more likely to have ever had an HIV test. African Americans/Blacks and individuals who had more positive evaluations of their appearance were more likely to have ever asked a partner's HIV status and to have asked a partner to get tested for HIV. Findings indicate low rates of HIV testing and communication with a partner about HIV, suggesting the importance of sexual health intervention and education programs for college students.

Cost-effectiveness of population based BRCA testing with varying Ashkenazi Jewish ancestry.

PubMed

Manchanda, Ranjit; Patel, Shreeya; Antoniou, Antonis C; Levy-Lahad, Ephrat; Turnbull, Clare; Evans, D Gareth; Hopper, John L; Macinnis, Robert J; Menon, Usha; Jacobs, Ian; Legood, Rosa

2017-11-01

Population-based BRCA1/BRCA2 testing has been found to be cost-effective compared with family history-based testing in Ashkenazi-Jewish women were >30 years old with 4 Ashkenazi-Jewish grandparents. However, individuals may have 1, 2, or 3 Ashkenazi-Jewish grandparents, and cost-effectiveness data are lacking at these lower BRCA prevalence estimates. We present an updated cost-effectiveness analysis of population BRCA1/BRCA2 testing for women with 1, 2, and 3 Ashkenazi-Jewish grandparents. Decision analysis model. Lifetime costs and effects of population and family history-based testing were compared with the use of a decision analysis model. 56% BRCA carriers are missed by family history criteria alone. Analyses were conducted for United Kingdom and United States populations. Model parameters were obtained from the Genetic Cancer Prediction through Population Screening trial and published literature. Model parameters and BRCA population prevalence for individuals with 3, 2, or 1 Ashkenazi-Jewish grandparent were adjusted for the relative frequency of BRCA mutations in the Ashkenazi-Jewish and general populations. Incremental cost-effectiveness ratios were calculated for all Ashkenazi-Jewish grandparent scenarios. Costs, along with outcomes, were discounted at 3.5%. The time horizon of the analysis is "life-time," and perspective is "payer." Probabilistic sensitivity analysis evaluated model uncertainty. Population testing for BRCA mutations is cost-saving in Ashkenazi-Jewish women with 2, 3, or 4 grandparents (22-33 days life-gained) in the United Kingdom and 1, 2, 3, or 4 grandparents (12-26 days life-gained) in the United States populations, respectively. It is also extremely cost-effective in women in the United Kingdom with just 1 Ashkenazi-Jewish grandparent with an incremental cost-effectiveness ratio of £863 per quality-adjusted life-years and 15 days life gained. Results show that population-testing remains cost-effective at the £20,000-30000 per quality-adjusted life-years and $100,000 per quality-adjusted life-years willingness-to-pay thresholds for all 4 Ashkenazi-Jewish grandparent scenarios, with ≥95% simulations found to be cost-effective on probabilistic sensitivity analysis. Population-testing remains cost-effective in the absence of reduction in breast cancer risk from oophorectomy and at lower risk-reducing mastectomy (13%) or risk-reducing salpingo-oophorectomy (20%) rates. Population testing for BRCA mutations with varying levels of Ashkenazi-Jewish ancestry is cost-effective in the United Kingdom and the United States. These results support population testing in Ashkenazi-Jewish women with 1-4 Ashkenazi-Jewish grandparent ancestry. Copyright © 2017 Elsevier Inc. All rights reserved.

Zebrafish on a chip: a novel platform for real-time monitoring of drug-induced developmental toxicity.

PubMed

Li, Yinbao; Yang, Fan; Chen, Zuanguang; Shi, Lijuan; Zhang, Beibei; Pan, Jianbin; Li, Xinchun; Sun, Duanping; Yang, Hongzhi

2014-01-01

Pharmaceutical safety testing requires a cheap, fast and highly efficient platform for real-time evaluation of drug toxicity and secondary effects. In this study, we have developed a microfluidic system for phenotype-based evaluation of toxic and teratogenic effects of drugs using zebrafish (Danio rerio) embryos and larvae as the model organism. The microfluidic chip is composed of two independent functional units, enabling the assessment of zebrafish embryos and larvae. Each unit consists of a fluidic concentration gradient generator and a row of seven culture chambers to accommodate zebrafish. To test the accuracy of this new chip platform, we examined the toxicity and teratogenicity of an anti-asthmatic agent-aminophylline (Apl) on 210 embryos and 210 larvae (10 individuals per chamber). The effect of Apl on zebrafish embryonic development was quantitatively assessed by recording a series of physiological indicators such as heart rate, survival rate, body length and hatch rate. Most importantly, a new index called clonic convulsion rate, combined with mortality was used to evaluate the toxicities of Apl on zebrafish larvae. We found that Apl can induce deformity and cardiovascular toxicity in both zebrafish embryos and larvae. This microdevice is a multiplexed testing apparatus that allows for the examination of indexes beyond toxicity and teratogenicity at the sub-organ and cellular levels and provides a potentially cost-effective and rapid pharmaceutical safety assessment tool.

Radioisotope-powered cardiac pacemaker program. Clinical studies of the nuclear pacemaker model NU-5. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-06-01

Beginning in February, 1970, the Nuclear Materials and Equipment Corporation (NUMEC) undertook a program to design, develop and manufacture a radioisotope powered cardiac pacemaker system. The scope of technical work was specified to be: establish system, component, and process cost reduction goals using the prototype Radioisotope Powered Cardiac Pacemaker (RCP) design and develop production techniques to achieve these cost reduction objectives; fabricate radioisotope powered fueled prototype cardiac pacemakers (RCP's) on a pilot production basis; conduct liaison with a Government-designated fueling facility for purposes of defining fueling requirements, fabrication and encapsulation procedures, safety design criteria and quality control and inspection requirements;more » develop and implement Quality Assurance and Reliability Programs; conduct performance, acceptance, lifetime and reliability tests of fueled RCP's in the laboratory; conduct liaison with the National Institutes of Health and with Government specified medical research institutions selected for the purpose of undertaking clinical evaluation of the RCP in humans; monitor and evaluate, on a continuing basis, all test data; and perform necessary safety analyses and tests. Pacemaker designs were developed and quality assurance and manufacturing procedures established. Prototype pacemakers were fabricated. A total of 126 radioisotope powered units were implanted and have been followed clinically for approximately seven years. Four (4) of these units have failed. Eighty-three (83) units remain implanted and satisfactorily operational. An overall failure rate of less than the target 0.15% per month has been achieved.« less

[System continuity and energy distribution in laser-induced thermo therapy (LITT)].

PubMed

Pech, M; Werk, M; Beck, A; Stohlmann, A; Ricke, J

2002-06-01

Evaluation of the continuity and energy distribution of a laser system for laser-induced thermo therapy. For evaluation of the continuity of laser optical devices, laser generating units and optical fibers of three different manufactures (Dornier, Hüttinger, Somatex), we used the equipment to generate a laser beam of 25 Watt for 60 minutes. Measurements of the applied energy were done sequentially with two MY Test (Fa. Hüttinger) units. We also performed two in vitro ablations of animal liver tissue with different fiber optics [Mikrodom A 13-0540, Microflexx REF A 13-0561 (Hüttinger), Diffusor-Tip H-6111-T 3, Diffusor H-6111-T 4 (Dornier), Somaflex-Diffusor (Somatex)] over 20 minutes at- an energy flow of 25 J per second. We then evaluated the geometry of coagulation. The different equipment used for our tests showed differences of a maximum of 10 %. Some components did not work properly in certain configurations even though the manufacturer assured it would. We saw significant differences in the ablation characteristics of the different fiber optics, especially in axial and frontal directions. Knowledge of the different characteristics in energy distribution and ablation characteristics are an important factor in performing a successful laser-induced thermo therapy.

Rapid Prototyping of an Aircraft Model in an Object-Oriented Simulation

NASA Technical Reports Server (NTRS)

Kenney, P. Sean

2003-01-01

A team was created to participate in the Mars Scout Opportunity. Trade studies determined that an aircraft provided the best opportunity to complete the science objectives of the team. A high fidelity six degree of freedom flight simulation was required to provide credible evidence that the aircraft design fulfilled mission objectives and to support the aircraft design process by providing performance evaluations. The team created the simulation using the Langley Standard Real-Time Simulation in C++ (LaSRS++) application framework. A rapid prototyping approach was necessary because the team had only three months to both develop the aircraft simulation model and evaluate aircraft performance as the design and mission parameters matured. The design of LaSRS++ enabled rapid-prototyping in several ways. First, the framework allowed component models to be designed, implemented, unit-tested, and integrated quickly. Next, the framework provides a highly reusable infrastructure that allowed developers to maximize code reuse while concentrating on aircraft and mission specific features. Finally, the framework reduces risk by providing reusable components that allow developers to build a quality product with a compressed testing cycle that relies heavily on unit testing of new components.

[Evaluation of the vital emergency action plan at the Navarre Hospital (Spain)].

PubMed

Tirapu, Belén; Rodrigo, Isabel; Gost, Javier; Aranguren, María Isabel; Ezcurra, Paz

2010-07-01

Healthcare organizations are placing great emphasis on the care of patients with cardiopulmonary arrest (CPA) since interventions based on the scientific evidence can decrease both the mortality rate and sequelae. Nevertheless, there are limited comprehensive assessments covering all the resources and interventions required when a vital emergency arises. To evaluate the effectiveness of the vital emergency action plan at the Navarre Hospital by analyzing a panel of 70 indicators. Structure and process indicators were assessed in 25 clinical units at the Navarre Hospital from April to June 2008. The structure and review process of CPR carts were analyzed, defibrillators were tested and 40 simulations involving 144 professionals were evaluated. Nonconformities were found in 86% of the indicators evaluated. The percentages of compliance in the indicators of structure ranged from 39.6% to 100%. In the evaluation of process, conformity ranged from 2.5% to 100%. The percentages of simulations meeting time standards varied between 17.5% and 45%. In 37.5% of the simulations, at least 50% of trained staff were present in the unit. In 32.3% of the simulations, the standard for the number of people in the unit who participated in the simulations was achieved. This study identified problems in the structure and process of a vital emergency action plan without, at this stage, evaluating patient outcomes. Copyright © 2010 Elsevier España S.L. All rights reserved.

Western U.S.-Canada crossborder case study : activity 2 : task D : conduct regional and local trucking case studies

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Technical Capability Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM proje...

Prenatal Care Training.

ERIC Educational Resources Information Center

Hagen, Michael

Described is the development and evaluation of a prenatal instructional program designed to prevent birth defects. It is explained that the program, composed of five slide tape units on such topics as nutrition and environmental factors, was field tested and found effective with 97 participants (pregnant high school students, nursing students, and…

Frequency of and risk factors for poor cognitive performance in hemodialysis patients

USDA-ARS?s Scientific Manuscript database

There are few detailed data on cognition in patients undergoing dialysis. We evaluated the frequency of and risk factors for poor cognitive performance using detailed neurocognitive testing. In this cross-sectional cohort study, 314 hemodialysis patients from 6 Boston-area hemodialysis units underwe...

EVALUATION OF AN ADVANCED ENGINEERING TEST REACTOR DESIGN

DOE Office of Scientific and Technical Information (OSTI.GOV)

McVey, M.; Bradfute, J.O.; Buck, K.E.

1958-07-15

The scope of the study was primarily concerned with optimization of the geometrical and core-composition variables to achieve maximum flux in the loop region per unit core power without exceeding heat transfer and other engineering limitations. Centain other design questions are to be investigated. (A.C.)

Development of Computer-Based Resources for Textile Education.

ERIC Educational Resources Information Center

Hopkins, Teresa; Thomas, Andrew; Bailey, Mike

1998-01-01

Describes the production of computer-based resources for students of textiles and engineering in the United Kingdom. Highlights include funding by the Teaching and Learning Technology Programme (TLTP), courseware author/subject expert interaction, usage test and evaluation, authoring software, graphics, computer-aided design simulation, self-test…

A qualitative assessment of the role of shippers and others in driver compliance with federal safety regulations

DOT National Transportation Integrated Search

2012-08-01

This report presents the test plan for conducting the Decision Support System Analysis for the United States Department of Transportation (U.S. DOT) evaluation of the San Diego Integrated Corridor Management (ICM) Initiative Demonstration. The ICM pr...

A Module Experimental Process System Development Unit (MEPSDU)

NASA Technical Reports Server (NTRS)

1981-01-01

A cost effective process sequence and machinery for the production of flat plate photovoltaic modules are described. Cells were fabricated using the process sequence which was optimized, as was a lamination procedure. Insulator tapes and edge seal material were identified and tested. Encapsulation materials were evaluated.

Notched Strength Allowables and Inplane Shear Strength of AS4/VRM-34 Textile Laminates

NASA Technical Reports Server (NTRS)

Grenoble, Ray W.; Johnston, William M.

2013-01-01

Notched and unnotched strength allowables were developed for a textile composite to provide input data to analytical structural models based on the Pultruded Rod Stiffened Efficient Unitized Structure (PRSEUS) concept. Filled-hole tensile strength, filled-hole compressive strength, and inplane shear strength along stitch lines have been measured. The material system evaluated in this study is based on warp-knitted preforms of AS4 carbon fibers and VRM-34 epoxy resin, which have been processed via resin infusion and oven curing. All specimens were tested in as-fabricated (dry) condition. Filled-hole strengths were evaluated with and without through-thickness stitching. The effects of scaling on filled-hole tensile strength were evaluated by testing specimens in two widths, but with identical width / hole-diameter ratios. Inplane shear specimens were stitched in two configurations, and two specimen thicknesses were tested for each stitch configuration.

Newborn physiological responses to noise in the neonatal unit.

PubMed

Cardoso, Sandra Maria Schefer; Kozlowski, Lorena de Cássia; Lacerda, Adriana Bender Moreira de; Marques, Jair Mendes; Ribas, Angela

2015-01-01

The incorporation of technologies in the care of infants has contributed to increased survival; however, this has turned neonatal unit into a noisy environment. To evaluate the physiological and functional effects resulting from the exposure to noise on low-weight newborns in incubators in a neonatal unit. Prospective, observational, quantitative, exploratory, descriptive study. The adopted statistical method included tables of frequency, descriptive statistics, and Student's t-test, with a 0.05 level of significance. As data collection tools, the environmental noise and the noise inside of the incubator were evaluated, and the Assessment of Preterm Infant Behavior scale was used to assess premature newborn behavior and projected specifically to document the neurobehavioral functioning of preterm infants. The data collection occurred from September of 2012 to April of 2013; 61 low-weight newborns admitted in the neonatal unit and in incubators were observed. Significant differences in the variables heart rate and oxygen saturation were noted when newborns were exposed to noise. Low-weight neonates in incubators present physiological alterations when facing discomfort caused by environmental noise in neonatal units. Copyright © 2015 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

EMC Testing on the Integrated Science Instrument Module (ISIM) - A Summary of the EMC Test Campaign for the Science Payload of the James Webb Space Telescope (JWST)

NASA Technical Reports Server (NTRS)

McCloskey, John

2016-01-01

This paper describes the electromagnetic compatibility (EMC) tests performed on the Integrated Science Instrument Module (ISIM), the science payload of the James Webb Space Telescope (JWST), at NASAs Goddard Space Flight Center (GSFC) in August 2015. By its very nature of being an integrated payload, it could be treated as neither a unit level test nor an integrated spacecraft/observatory test. Non-standard test criteria are described along with non-standard test methods that had to be developed in order to evaluate them. Results are presented to demonstrate that all test criteria were met in less than the time allocated.

Ethanol production in small- to medium-size facilities

NASA Astrophysics Data System (ADS)

Hiler, E. A.; Coble, C. G.; Oneal, H. P.; Sweeten, J. M.; Reidenbach, V. G.; Schelling, G. T.; Lawhon, J. T.; Kay, R. D.; Lepori, W. A.; Aldred, W. H.

1982-04-01

In early 1980 system design criteria were developed for a small-scale ethanol production plant. The plant was eventually installed on November 1, 1980. It has a production capacity of 30 liters per hour; this can be increased easily (if desired) to 60 liters per hour with additional fermentation tanks. Sixty-six test runs were conducted to date in the alcohol production facility. Feedstocks evaluated in these tests include: corn (28 runs); grain sorghum (33 runs); grain sorghum grits (1 run); half corn/half sorghum (1 run); and sugarcane juice (3 runs). In addition, a small bench-scale fermentation and distillation system was used to evaluate sugarcane and sweet sorghum feedstocks prior to their evaluation in the larger unit. In each of these tests, evaluation of the following items was conducted: preprocessing requirements; operational problems; conversion efficiency (for example, liters of alcohol produced per kilogram of feedstock); energy balance and efficiency; nutritional recovery from stillage; solids separation by screw press; chemical characterization of stillage including liquid and solids fractions; wastewater requirements; and air pollution potential.

Experimental Evaluation of High Performance Integrated Heat Pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, William A; Berry, Robert; Durfee, Neal

2016-01-01

Integrated heat pump (IHP) technology provides significant potential for energy savings and comfort improvement for residential buildings. In this study, we evaluate the performance of a high performance IHP that provides space heating, cooling, and water heating services. Experiments were conducted according to the ASHRAE Standard 206-2013 where 24 test conditions were identified in order to evaluate the IHP performance indices based on the airside performance. Empirical curve fits of the unit s compressor maps are used in conjunction with saturated condensing and evaporating refrigerant conditions to deduce the refrigerant mass flowrate, which, in turn was used to evaluate themore » refrigerant side performance as a check on the airside performance. Heat pump (compressor, fans, and controls) and water pump power were measured separately per requirements of Standard 206. The system was charged per the system manufacturer s specifications. System test results are presented for each operating mode. The overall IHP performance metrics are determined from the test results per the Standard 206 calculation procedures.« less

Space shuttle orbital maneuvering engine platelet injector program

NASA Technical Reports Server (NTRS)

1975-01-01

A platelet face injector for the Orbit Maneuvering Engine (OME) on the space shuttle was evaluated as a means of obtaining additional design margin and lower cost. The program was conducted in three phases. The first phase evaluated single injection elements, or unielements; it involved visual flow studies, mixing experiments using propellant simulants, and hot firings to assess combustion efficiency, chamber wall compatibility, and injector face temperatures. In the second phase, subscale units producing 600 lbf thrust were used to further evaluate the orifice patterns chosen on the basis of unielement testing. In addition to combustion efficiency, chamber and injector heat transfer, the subscale testing provided a preliminary indication of injector stability. Full scale testing of the selected patterns at 6,000 lbf thrust was performed in the third phase. Performance, heat transfer, and combustion stability were evaluated over the anticipated range of OMS operating conditions. The effects on combustion stability of acoustic cavity configuration, including cavity depth, open area, inlet contour, and other parameters, were investigated.

Corrective Action Investigation Plan for Corrective Action Unit 414: Clean Slate III Plutonium Dispersion (TTR) Tonopah Test Range, Nevada, Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matthews, Patrick

Corrective Action Unit (CAU) 414 is located on the Tonopah Test Range, which is approximately 130 miles northwest of Las Vegas, Nevada, and approximately 40 miles southeast of Tonopah, Nevada. The CAU 414 site consists of the release of radionuclides to the surface and shallow subsurface from the conduct of the Clean Slate III (CSIII) storage–transportation test conducted on June 9, 1963. CAU 414 includes one corrective action site (CAS), TA-23-03CS (Pu Contaminated Soil). The known releases at CAU 414 are the result of the atmospheric dispersal of contamination from the 1963 CSIII test. The CSIII test was a nonnuclearmore » detonation of a nuclear device located inside a reinforced concrete bunker covered with 8 feet of soil. This test dispersed radionuclides, primarily uranium and plutonium, on the ground surface. The presence and nature of contamination at CAU 414 will be evaluated based on information collected from a corrective action investigation (CAI). The investigation is based on the data quality objectives (DQOs) developed on June 7, 2016, by representatives of the Nevada Division of Environmental Protection; the U.S. Air Force; and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective action alternatives for CAU 414.« less