Study on the immunological safety of universal plasma in the Chinese population in vitro.

PubMed

Chen, Guanyi; Zhu, Liguo; Wang, Shufang; Zhuang, Yuan; Yu, Yang; Wang, Deqing

2017-04-01

The prepared procedure for universal plasma in the Chinese population has been developed. However, the immunological safety with the level of antibodies, soluble immune complexes and complements is necessary to investigate. The universal plasma was pooled at the optimal ratio of A:B:AB=6:2.5:1.5 at 22°C for 1 hour. The titer of IgM antibodies was detected by saline agglutination, and the titer of IgG antibodies was detected by a Polybrene test after IgM destroyed by 2-mereaptoethanol. The hemolysis extent of RBC was investigated by an extracorporal hemolysis test, and the concentration of free-hemoglobin was determined by the ortho-tolidine method. The levels of CIC-C1q, C3b and TCC (C5-9) were tested using an enzyme linked immunosorbent assay (ELISA). The titer of IgM and IgG in universal plasma was lower than 2 and 4, respectively. The hemolysis of the universal plasma with A, B and AB group RBCs was negative with values of 5.5, 6.8 and 5.7, respectively. The level of CIC-C1q and TCC (C5-9) in universal plasma was comparable to that in A or B type pooled plasma, but CIC-C1q was lower than that and TCC (C5-9) was higher than that in AB type pooled plasma. The level of complement C3b was comparable to that in A type pooled plasma, but lower than that in B type pooled plasma and higher than that in AB type pooled plasma. The results of this study demonstrated that the immunological levels were within an acceptable range and confirmed the safety in vitro. Copyright © 2016 Elsevier Ltd. All rights reserved.

SULTAN measurement and qualification: ITER-US-LLNL-NMARTOVETSKY- 092008

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martovetsky, N N

2006-09-21

Measuring the characteristics of full scale ITER CICC at SULTAN is the critical qualification test. If volt-ampere characteristic (VAC) or volt-temperature characteristic (VTC) are distorted, the criterion of 10 uV/m may not be a valid criterion to judge the conductor performance. Only measurements with a clear absence or low signals from the current distribution should be considered as quantitatively representative, although in some obvious circumstances one can judge if a conductor will meet or fail ITER requirements. SULTAN full scale ITER CICC testing should be done with all measures taken to ensure uniform current redistribution. A full removal of Crmore » plating in the joint area and complete solder filling of the joints (with provision of the central channel for helium flow) should be mandatory for DC qualification samples for ITER. Also, T and I should be increased slowly that an equilibrium could be established for accurate measurement of Tcs, Ic and N. It is also desirable to go up in down in current and/or temperature (within stable range) to make sure that the equilibrium is reached.« less

Genome Sequence of Paenibacillus polymyxa Strain CICC 10580, Isolated from the Fruit of Noni (Morinda citrifolia L.) Grown in the Paracel Islands.

PubMed

Xu, Youqiang; Liu, Yang; Yao, Su; Li, Jinxia; Cheng, Chi

2014-08-28

Noni is a plant reported to have nutritional and therapeutic properties. Paenibacillus polymyxa CICC 10580 is a strain that was isolated from the fruit of noni and showed comprehensive antagonistic activity against many pathogens. Its genome was sequenced and assembled (6.10 Mb). The coding sequences (CDSs) correlated with antagonistic activity were annotated. Copyright © 2014 Xu et al.

Metallographic autopsies of full-scale ITER prototype cable-in-conduit conductors after full cyclic testing in SULTAN: III. The importance of strand surface roughness in long twist pitch conductors

DOE PAGES

Sanabria, Charlie; Lee, Peter J.; Starch, William; ...

2016-05-31

As part of the ITER conductor qualification process, 3 m long Cable-in-Conduit Conductors (CICCs) were tested at the SULTAN facility under conditions simulating ITER operation so as to establish the current sharing temperature, T cs, as a function of multiple full Lorentz force loading cycles. After a comprehensive evaluation of both the Toroidal Field (TF) and the Central Solenoid (CS) conductors, it was found that T cs degradation was common in long twist pitch TF conductors while short twist pitch CS conductors showed some T cs increase. However, one kind of TF conductors containing superconducting strand fabricated by the Bochvarmore » Institute of Inorganic Materials (VNIINM) avoided T cs degradation despite having long twist pitch. In our earlier metallographic autopsies of long and short twist pitch CS conductors, we observed a substantially greater transverse strand movement under Lorentz force loading for long twist pitch conductors, while short twist pitch conductors had negligible transverse movement. With help from the literature, we concluded that the transverse movement was not the source of T cs degradation but rather an increase of the compressive strain in the Nb 3Sn filaments possibly induced by longitudinal movement of the wires. Like all TF conductors this TF VNIINM conductor showed large transverse motions under Lorentz force loading, but Tcs actually increased, as in all short twist pitch CS conductors. We here propose that the high surface roughness of the VNIINM strand may be responsible for the suppression of the compressive strain enhancement (characteristic of long twist pitch conductors). Furthermore, it appears that increasing strand surface roughness could improve the performance of long twist pitch CICCs.« less

Metallographic autopsies of full-scale ITER prototype cable-in-conduit conductors after full cyclic testing in SULTAN: III. The importance of strand surface roughness in long twist pitch conductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanabria, Charlie; Lee, Peter J.; Starch, William

As part of the ITER conductor qualification process, 3 m long Cable-in-Conduit Conductors (CICCs) were tested at the SULTAN facility under conditions simulating ITER operation so as to establish the current sharing temperature, T cs, as a function of multiple full Lorentz force loading cycles. After a comprehensive evaluation of both the Toroidal Field (TF) and the Central Solenoid (CS) conductors, it was found that T cs degradation was common in long twist pitch TF conductors while short twist pitch CS conductors showed some T cs increase. However, one kind of TF conductors containing superconducting strand fabricated by the Bochvarmore » Institute of Inorganic Materials (VNIINM) avoided T cs degradation despite having long twist pitch. In our earlier metallographic autopsies of long and short twist pitch CS conductors, we observed a substantially greater transverse strand movement under Lorentz force loading for long twist pitch conductors, while short twist pitch conductors had negligible transverse movement. With help from the literature, we concluded that the transverse movement was not the source of T cs degradation but rather an increase of the compressive strain in the Nb 3Sn filaments possibly induced by longitudinal movement of the wires. Like all TF conductors this TF VNIINM conductor showed large transverse motions under Lorentz force loading, but Tcs actually increased, as in all short twist pitch CS conductors. We here propose that the high surface roughness of the VNIINM strand may be responsible for the suppression of the compressive strain enhancement (characteristic of long twist pitch conductors). Furthermore, it appears that increasing strand surface roughness could improve the performance of long twist pitch CICCs.« less

First AC loss test and analysis of a Bi2212 cable-in-conduit conductor for fusion application

NASA Astrophysics Data System (ADS)

Qin, Jinggang; Shi, Yi; Wu, Yu; Li, Jiangang; Wang, Qiuliang; He, Yuxiang; Dai, Chao; Liu, Fang; Liu, Huajun; Mao, Zhehua; Nijhuis, Arend; Zhou, Chao; Devred, Arnaud

2018-01-01

The main goal of the Chinese fusion engineering test reactor (CFETR) is to build a fusion engineering tokamak reactor with a fusion power of 50-200 MW, and plan to test the breeding tritium during the fusion reaction. This may require a maximum magnetic field of the central solenoid and toroidal field coils up to 15 T. New magnet technologies should be developed for the next generation of fusion reactors with higher requirements. Bi2Sr2CaCu2Ox (Bi2212) is considered as a potential and promising superconductor for the magnets in the CFETR. R&D activities are ongoing at the Institute of Plasma Physics, Chinese Academy of Sciences for demonstration of the feasibility of a CICC based on Bi2212 round wire. One sub-size conductor cabled with 42 wires was designed, manufactured and tested with limited strand indentation during cabling and good transport performance. In this paper, the first test results and analysis on the AC loss of Bi2212 round wires and cabled conductor samples are presented. Furthermore, the impact of mechanical load on the AC loss of the sub-size conductor is investigated to represent the operation conditions with electromagnetic loads. The first tests provide an essential basis for the validation of Bi2212 CICC and its application in fusion magnets.

The amyR-deletion strain of Aspergillus niger CICC2462 is a suitable host strain to express secreted protein with a low background.

PubMed

Zhang, Hui; Wang, Shuang; Zhang, Xiang Xiang; Ji, Wei; Song, Fuping; Zhao, Yue; Li, Jie

2016-04-28

The filamentous fungus Aspergillus niger is widely exploited as an important expression host for industrial production. The glucoamylase high-producing strain A. niger CICC2462 has been used as a host strain for the establishment of a secretion expression system. It expresses recombinant xylanase, mannase and asparaginase at a high level, but some high secretory background proteins in these recombinant strains still remain, such as alpha-amylase and alpha-glucosidase; lead to a low-purity of fermentation products. The aim was to construct an A. niger host strain with a low background of protein secretion. The transcription factor amyR was deleted in A. niger CICC2462, and the results from enzyme activity assays and SDS-PAGE analysis showed that the glucoamylase and amylase activities of the ∆amyR strains were significantly lower than those of the wild-type strain. High-throughput RNA-sequencing and shotgun LC-MS/MS proteomic technology analysis demonstrated that the expression of amylolytic enzymes was decreased at both the transcriptional and translational levels in the ∆amyR strain. Interestingly, the ∆amyR strain growth rate better than the wild-type strain. Our findings clearly indicated that the ∆amyR strain of A. niger CICC2462 can be used as a host strain with a low background of protein secretion.

Transverse heat transfer coefficient in the dual channel ITER TF CICCs Part II. Analysis of transient temperature responses observed during a heat slug propagation experiment

NASA Astrophysics Data System (ADS)

Lewandowska, Monika; Herzog, Robert; Malinowski, Leszek

2015-01-01

A heat slug propagation experiment in the final design dual channel ITER TF CICC was performed in the SULTAN test facility at EPFL-CRPP in Villigen PSI. We analyzed the data resulting from this experiment to determine the equivalent transverse heat transfer coefficient hBC between the bundle and the central channel of this cable. In the data analysis we used methods based on the analytical solutions of a problem of transient heat transfer in a dual-channel cable, similar to Renard et al. (2006) and Bottura et al. (2006). The observed experimental and other limits related to these methods are identified and possible modifications proposed. One result from our analysis is that the hBC values obtained with different methods differ by up to a factor of 2. We have also observed that the uncertainties of hBC in both methods considered are much larger than those reported earlier.

Evaluation of immunomodulatory activity of two potential probiotic Lactobacillus strains by in vivo tests.

PubMed

Ren, Dayong; Li, Chang; Qin, Yanqing; Yin, Ronglan; Du, Shouwen; Liu, Hongfeng; Zhang, Yanfang; Wang, Cuiyan; Rong, Fengjun; Jin, Ningyi

2015-10-01

Here we evaluate the immunomodulatory function of two potential probiotic strains, Lactobacillus salivarius CICC 23174 and Lactobacillus plantarum CGMCC 1.557. Mice were fed with each Lactobacillus strain at different doses for several consecutive days. The effects of the two probiotic strains on immune organs, immune cells and immune molecules were investigated on days 10 and 20. Both Lactobacillus strains increased the spleen index, improved the spleen lymphocyte transformation rate, enhanced sIgA production and improved the number of CD11c(+) CD80(+) double-positive cells. L. plantarum CGMCC 1.557 was the more active strain in enhancing the phagocytic activity of macrophages, while, L. salivarius CICC 23174 was the more effective strain at maintaining the Th1/Th2 balance. This study suggests that these two Lactobacillus strains have beneficial effects on regulation of immune responses, which has promising implications for the development of ecological agents and functional foods. Copyright © 2015 Elsevier Ltd. All rights reserved.

Electromagnetic analysis of a superconducting transformer for high current characterization of cable in conduit conductors in background magnetic field

NASA Astrophysics Data System (ADS)

Wu, Xiangyang; Tan, Yunfei; Fang, Zhen; Jiang, Donghui; Chen, Zhiyou; Chen, Wenge; Kuang, Guangli

2017-10-01

A large cable-in-conduit-conductor (CICC) test facility has been designed and fabricated at the High Magnetic Field Laboratory of the Chinese Academy of Sciences (CHMFL) in order to meet the test requirement of the conductors which are applied to the future fusion reactor. The critical component of the test facility is an 80 kA superconducting transformer which consists of a multi-turn primary coil and a minor-turn secondary coil. As the current source of the conductor samples, the electromagnetic performance of the superconducting transformer determines the stability and safety of the test facility. In this paper, the key factors and parameters, which have much impact on the performance of the transformer, are analyzed in detail. The conceptual design and optimizing principles of the transformer are discussed. An Electromagnetic-Circuit coupled model built in ANSYS Multiphysics is successfully used to investigate the electromagnetic characterization of the transformer under the dynamic operation condition.

In vitro evaluation of the probiotic and functional potential of Lactobacillus strains isolated from fermented food and human intestine.

PubMed

Ren, Dayong; Li, Chang; Qin, Yanqing; Yin, Ronglan; Du, Shouwen; Ye, Fei; Liu, Cunxia; Liu, Hongfeng; Wang, Maopeng; Li, Yi; Sun, Yang; Li, Xiao; Tian, Mingyao; Jin, Ningyi

2014-12-01

This study aims to evaluate the functional and probiotic characteristics of eight indigenous Lactobacillus strains in vitro. The selected lactobacilli include strains of Lactobacillus casei subsp. casei, Lactobacillus salivarius subsp. salicinius, Lactobacillus fermentum, Lactobacillus plantarum, Lactobacillus delbrueckii subsp. lactis, Lactobacillus delbrueckii subsp. bulgaricus, and Lactobacillus rhamnosus. All strains tolerated both pH 2 for 3 h and 1% bile salt for 24 h. The strains CICC 23174 and CGMCC 1.557 were the most adhesive strains producing the highest quantity of EPS. Although a wide variation in the ability of the eight strains to deplete cholesterol and nitrite, antagonize pathogens, scavenge free radical, and stimulate innate immune response were observed, the strains CICC 23174 and CGMCC 1.557 showed the widest range of these useful traits. Taken together, the strains CICC 23174 and CGMCC 1.557 exhibited the best probiotic properties with the potential for use in the production of probiotic fermented foods. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fatigue Properties of Modified 316LN Stainless Steel at 4 K for High Field Cable-In Applications

NASA Astrophysics Data System (ADS)

Toplosky, V. J.; Walsh, R. P.; Han, K.

2010-04-01

Cable-In-Conduit-Conductor (CICC) alloys, exposed to Nb3Sn reaction heat-treatments, such as modified 316LN require a design specific database. A lack of fatigue life data (S-n curves) that could be applied in the design of the ITER CS and the NHMFL Series Connected Hybrid magnets is the impetus for the research presented here. The modified 316LN is distinguished by a lower carbon content and higher nitrogen content when compared to conventional 316LN. Because the interstitial alloying elements affect the mechanical properties significantly, it is necessary to characterize this alloy in a systematic way. In conjunction, to ensure magnet reliability and performance, several criteria and expectations must be met, including: high fatigue life at the operating stresses, optimal stress management at cryogenic temperatures and thin walled conduit to reduce coil mass. Tension-tension load control axial fatigue tests have good applicability to CICC solenoid magnet design, thus a series of 4 K strength versus fatigue life curves have been generated. In-situ samples of 316LN base metal, seam welded, butt welded and seam plus butt welded are removed directly from the conduit in order to address base and weld material fatigue life variability. The more than 30 fatigue tests show good grouping on the fatigue life curve and allow discretionary 4 K fatigue life predictions for conduit made with modified 316LN.

Recent Progress of the Series-Connected Hybrid Magnet Projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adkins, Todd; Bole, Scott

2010-01-01

The National High Magnetic Field Laboratory (NHMFL) in Tallahassee, Florida has designed and is now constructing two Series Connected Hybrid (SCH) magnets, each connecting a superconducting outsert coil and a resistive Florida Bitter insert coil electrically in series. The SCH to be installed at the NHMFL will produce 36 T and provide 1 ppm maximum field inhomogeneity over a 1 cm diameter spherical volume. The SCH to be installed at the Helmholtz Center Berlin (HZB) in combination with a neutron source will produce 25 T to 30 T depending on the resistive insert. The two magnets have a common designmore » for their cable-in-conduit conductor (CICC) and superconducting outsert coils. The CICC outsert coil winding packs have an inner diameter of 0.6 m and contribute 13.1 T to the central field using three grades of CICC conductors. Each conductor grade carries 20 kA and employs the same type of Nb{sub 3}Sn superconducting wire, but each grade contains different quantities of superconducting wires, different cabling patterns and different aspect ratios. The cryostats and resistive insert coils for the two magnets are different. This paper discusses the progress in CIC conductor and coil fabrication over the last year including specification, qualification and production activities for wire, cable, conductor and coil processing.« less

Screening for strains with 11α-hydroxylase activity for 17α-hydroxy progesterone biotransformation.

PubMed

Gao, Qian; Qiao, Yuqian; Shen, Yanbing; Wang, Min; Wang, Xibo; Liu, Yang

2017-08-01

Various corticosteroids are prepared by using 11α,17α-diOH-progesterone (11α,17α-diOH-PROG) as an important intermediate and raw material. Hence, strains that can improve the yields of 11α,17α-diOH-PROG should be screened. Cunninghamella elegans CICC40250 was singled out from five common 11α hydroxylation strains. The reaction parameters of 11α,17α-diOH-PROG production were also investigated. C. elegans CICC40250 could efficiently catalyze the hydroxylation of 17α-hydroxy progesterone (17α-OH-PROG) at C-11α position. This strain could also effectively convert 11α,17α-diOH-PROG at high substrate concentrations (up to 30g/L). After the coenzyme precursor glucose was added, the rate of 11α,17α-diOH-PROG formation reached 84.2%, which was 11.4% higher than that of the control group. Our study established a simple and feasible mechanism to increase 11α,17α-diOH-PROG production levels. This mechanism involves C. elegans CICC40250 that can be efficiently applied to induce the biotransformation of 17α-OH-PROG with a hydroxylation biocatalytic ability. Copyright © 2017. Published by Elsevier Inc.

Theoretical analysis for the mechanical behavior caused by an electromagnetic cycle in ITER Nb3Sn cable-in-conduit conductors

NASA Astrophysics Data System (ADS)

Yue, Donghua; Zhang, Xingyi; Zhou, You-He

2018-02-01

The central solenoid (CS) is one of the key components of the International Thermonuclear Experimental Reactor (ITER) tokamak and which is often considered as the heart of this fusion reactor. This solenoid will be built by using Nb3Sn cable-in-conduit conductors (CICC), capable of generating a 13 T magnetic field. In order to assess the performance of the Nb3Sn CICC in nearly the ITER condition, many short samples have been evaluated at the SULTAN test facility (the background magnetic field is of 10.85 T with the uniform length of 400 mm at 1% homogeneity) in Centre de Recherches en Physique des Plasma (CRPP). It is found that the samples with pseudo-long twist pitch (including baseline specimens) show a significant degradation in the current-sharing temperature (Tcs), while the qualification tests of all short twist pitch (STP) samples, which show no degradation versus electromagnetic cycling, even exhibits an increase of Tcs. This behavior was perfectly reproduced in the coil experiments at the central solenoid model coil (CSMC) facility last year. In this paper, the complex structure of the Nb3Sn CICC would be simplified into a wire rope consisting of six petals and a cooling spiral. An analytical formula for the Tcs behavior as a function of the axial strain of the cable is presented. Based on this, the effects of twist pitch, axial and transverse stiffness, thermal mismatch, cycling number, magnetic distribution, etc., on the axial strain are discussed systematically. The calculated Tcs behavior with cycle number show consistency with the previous experimental results qualitatively and quantitatively. Lastly, we focus on the relationship between Tcs and axial strain of the cable, and we conclude that the Tcs behavior caused by electromagnetic cycles is determined by the cable axial strain. Once the cable is in a compression situation, this compression strain and its accumulation would lead to the Tcs degradation. The experimental observation of the Tcs enhancement in the CS STP samples should be considered as a contribution of the shorter length of the high field zone in SULTAN and CSMC devices, as well as the tight cable structure.

Using the HELIOS facility for assessment of bundle-jacket thermal coupling in a CICC

NASA Astrophysics Data System (ADS)

Lacroix, B.; Rousset, B.; Cloez, H.; Decool, P.; Duchateau, J. L.; Hoa, C.; Luchier, N.; Nicollet, S.; Topin, F.

2016-12-01

In a Cable In Conduit Conductor (CICC) cooled by forced circulation of supercritical helium, the heat exchange in the bundle region can play a significant role for conductor safe operation, while remaining a quite uncertain parameter. Heat exchange between bundle and jacket depends on the relative contributions of convective heat transfer due to the helium flow inside the bundle and of thermal resistance due to the wrappings between the cable and the conduit. In order to qualify this thermal coupling at realistic operating conditions, a dedicated experiment on a 1.2 m sample of ITER Toroidal Field (TF) dummy conductor was designed and performed in the HELIOS test facility at CEA Grenoble. Several methods were envisaged, and the choice was made to assess bundle-jacket heat transfer coefficient by measuring the temperature of a solid copper cylinder inserted over the conductor jacket and submitted to heat deposition on its outer surface. The mock-up was manufactured and tested in spring 2015. Bundle-jacket heat transfer coefficient was found in the range 300-500 W m-2 K-1. Results analysis suggests that the order of magnitude of convective heat transfer coefficient inside bundle is closer to Colburn-Reynolds analogy than to Dittus-Boelter correlation, and that bundle-jacket thermal coupling is mainly limited by thermal resistance due to wrappings. A model based on an equivalent layer of stagnant helium between wraps and jacket was proposed and showed a good consistency with the experiment, with relevant values for the helium layer thickness.

Results and analysis of the hot-spot temperature experiment for a cable-in-conduit conductor with thick conduit

NASA Astrophysics Data System (ADS)

Sedlak, Kamil; Bruzzone, Pierluigi

2015-12-01

In the design of future DEMO fusion reactor a long time constant (∼23 s) is required for an emergency current dump in the toroidal field (TF) coils, e.g. in case of a quench detection. This requirement is driven mainly by imposing a limit on forces on mechanical structures, namely on the vacuum vessel. As a consequence, the superconducting cable-in-conduit conductors (CICC) of the TF coil have to withstand heat dissipation lasting tens of seconds at the section where the quench started. During that time, the heat will be partially absorbed by the (massive) steel conduit and electrical insulation, thus reducing the hot-spot temperature estimated strictly from the enthalpy of the strand bundle. A dedicated experiment has been set up at CRPP to investigate the radial heat propagation and the hot-spot temperature in a CICC with a 10 mm thick steel conduit and a 2 mm thick glass epoxy outer electrical insulation. The medium size, ∅ = 18 mm, NbTi CICC was powered by the operating current of up to 10 kA. The temperature profile was monitored by 10 temperature sensors. The current dump conditions, namely the decay time constant and the quench detection delay, were varied. The experimental results show that the thick conduit significantly contributes to the overall enthalpy balance, and consequently reduces the amount of copper required for the quench protection in superconducting cables for fusion reactors.

Producing Acetic Acid of Acetobacter pasteurianus by Fermentation Characteristics and Metabolic Flux Analysis.

PubMed

Wu, Xuefeng; Yao, Hongli; Liu, Qing; Zheng, Zhi; Cao, Lili; Mu, Dongdong; Wang, Hualin; Jiang, Shaotong; Li, Xingjiang

2018-03-19

The acetic acid bacterium Acetobacter pasteurianus plays an important role in acetic acid fermentation, which involves oxidation of ethanol to acetic acid through the ethanol respiratory chain under specific conditions. In order to obtain more suitable bacteria for the acetic acid industry, A. pasteurianus JST-S screened in this laboratory was compared with A. pasteurianus CICC 20001, a current industrial strain in China, to determine optimal fermentation parameters under different environmental stresses. The maximum total acid content of A. pasteurianus JST-S was 57.14 ± 1.09 g/L, whereas that of A. pasteurianus CICC 20001 reached 48.24 ± 1.15 g/L in a 15-L stir stank. Metabolic flux analysis was also performed to compare the reaction byproducts. Our findings revealed the potential value of the strain in improvement of industrial vinegar fermentation.

Antimicrobial activity of plant essential oils against bacterial and fungal species involved in food poisoning and/or food decay.

PubMed

Lixandru, Brînduşa-Elena; Drăcea, Nicoleta Olguţa; Dragomirescu, Cristiana Cerasella; Drăgulescu, Elena Carmina; Coldea, Ileana Luminiţa; Anton, Liliana; Dobre, Elena; Rovinaru, Camelia; Codiţă, Irina

2010-01-01

The currative properties of aromatic and medicinal plants have been recognized since ancient times and, more recently, the antimicrobial activity of plant essential oils has been used in several applications, including food preservation. The purpose of this study was to create directly comparable, quantitative data on the antimicrobial activity of some plant essential oils prepared in the National Institute of Research-Development for Chemistry and Petrochemistry, Bucharest to be used for the further development of food packaging technology, based on their antibacterial and antifungal activity. The essential oils extracted from thyme (Thymus vulgaris L.), basil (Ocimum basilicum L.), coriander (Coriandrum sativum L.), rosemary (Rosmarinus officinalis L.), sage (Salvia officinalis L.), fennel (Foeniculum vulgare L.), spearmint (Mentha spicata L.) and carraway (Carum carvi L.) were investigated for their antimicrobial activity against eleven different bacterial and three fungal strains belonging to species reported to be involved in food poisoning and/or food decay: S. aureus ATCC 25923, S. aureus ATCC 6538, S. aureus ATCC 25913, E. coli ATCC 25922, E. coli ATCC 35218, Salmonella enterica serovar Enteritidis Cantacuzino Institute Culture Collection (CICC) 10878, Listeria monocytogenes ATCC 19112, Bacillus cereus CIP 5127, Bacillus cereus ATCC 11778, Candida albicans ATCC 10231, Aspergillus niger ATCC 16404, Penicillium spp. CICC 251 and two E. coli and Salmonella enterica serovar Enteritidis clinical isolates. The majority of the tested essential oils exibited considerable inhibitory capacity against all the organisms tested, as supported by growth inhibition zone diameters, MICs and MBC's. Thyme, coriander and basil oils proved the best antibacterial activity, while thyme and spearmint oils better inhibited the fungal species.

Infusing Culture in Career Counseling

ERIC Educational Resources Information Center

Arthur, Nancy; Collins, Sandra

2011-01-01

This article introduces the culture-infused career counselling (CICC) model. Six principles are foundational to a tripartite model emphasizing cultural self-awareness, awareness of client cultural identities, and development of a culturally sensitive working alliance. The core competencies ensure the cultural validity and relevance of career…

Fermentation Process and Metabolic Flux of Ethanol Production from the Detoxified Hydrolyzate of Cassava Residue

PubMed Central

Li, Xingjiang; Deng, Yongdong; Yang, Ying; Wei, Zhaojun; Cheng, Jieshun; Cao, Lili; Mu, Dongdong; Luo, Shuizhong; Zheng, Zhi; Jiang, Shaotong; Wu, Xuefeng

2017-01-01

With the growth of the world population, energy problems are becoming increasingly severe; therefore, sustainable energy sources have gained enormous importance. With respect to ethanol fuel production, biomass is gradually replacing grain as the main raw material. In this study, we explored the fermentation of five- and six-carbon sugars, the main biomass degradation products, into alcohol. We conducted mutagenic screening specifically for Candida tropicalis CICC1779 to obtain a strain that effectively used xylose (Candida tropicalis CICC1779-Dyd). By subsequently studying fermentation conditions under different initial liquid volume oxygen transfer coefficients (kLα), and coupling control of the aeration rate and agitation speed under optimal conditions, the optimal dissolved oxygen change curve was obtained. In addition, we constructed metabolic flow charts and equations to obtain a better understanding of the fermentation mechanism and to improve the ethanol yield. In our experiment, the ethanol production of the wild type stain was 17.58 g·L−1 at a kLα of 120. The highest ethanol yield of the mutagenic strains was 24.85 g·L−1. The ethanol yield increased to 26.56 g·L−1 when the dissolved oxygen content was optimized, and the conversion of sugar into alcohol reached 0.447 g·g−1 glucose (the theoretical titer of yeast-metabolized xylose was 0.46 g ethanol/g xylose and the glucose ethanol fermentation titer was 0.51 g ethanol/g glucose). Finally, the detected activity of xylose reductase and xylose dehydrogenase was higher in the mutant strain than in the original, which indicated that the mutant strain (CICC1779-Dyd) could effectively utilize xylose for metabolism. PMID:28878755

Cool-Down and Current Test Results of the KSTAR Prototype TF Coil

NASA Astrophysics Data System (ADS)

Oh, Y. K.; Lee, S.; Chu, Y.; Park, K. R.; Yonekawa, H.; Baek, S. H.; Cho, K. W.; Park, Y. M.; Kim, M. K.; Chang, H. S.; Kim, Y. S.; Chang, Y. B.; Lee, Y. J.; Kim, W. C.; Kim, K.; Kwag, S. W.; Lee, S. H.; Yang, S. H.; Lee, S. J.; Bak, J. S.; Lee, G. S.

2004-06-01

A prototype toroidal field (TF) coil, TF00 coil, of the Korea Superconducting Tokamak Advanced Research (KSTAR) project has been assembled and tested at the coil test facility in Korea Basic Science Institute (KBSI). The TF00 coil is a real-sized TF coil made of Nb3Sn superconducting cable-in-conduit conductor (CICC). The coil test was conducted by several campaigns according to the objectives. The first campaign, which was carried out by Jan. 2003, has objectives of cooling the coil into operating temperature and finding any defect in the coil such as cold leaks. From the results of the first campaign experiment, any defect in the coil was not found. The second campaign, which was carried out by Aug. 2003, has objectives to get the operating characteristics according to the current ramp up and discharge operations. In this paper, the coil test results are introduced as well as the details of the coil test system setup.

Fundamental Issues in Space Electronics Reliability: Negative Bias Temperature Instability

DTIC Science & Technology

2010-12-01

Mintarno, S. Mitra, S. Krishnan, Y. Cao, “Circuit Aging Prediction for Low-Power Operation,” Proc. IEEE/CICC (2009) [7] D. A Neaman , Semiconductor Physics...dielectric based field effect transistors,” J. Appl. Phys. 104 124109 (2008) [6] D. A Neaman , Semiconductor Physics and Devices, NY: McGraw Hill

Computational quench model applicable to the SMES/CICC

NASA Astrophysics Data System (ADS)

Luongo, Cesar A.; Chang, Chih-Lien; Partain, Kenneth D.

1994-07-01

A computational quench model accounting for the hydraulic peculiarities of the 200 kA SMES cable-in-conduit conductor has been developed. The model is presented and used to simulate the quench on the SMES-ETM. Conclusions are drawn concerning quench detection and protection. A plan for quench model validation is presented.

Global insights into acetic acid resistance mechanisms and genetic stability of Acetobacter pasteurianus strains by comparative genomics

NASA Astrophysics Data System (ADS)

Wang, Bin; Shao, Yanchun; Chen, Tao; Chen, Wanping; Chen, Fusheng

2015-12-01

Acetobacter pasteurianus (Ap) CICC 20001 and CGMCC 1.41 are two acetic acid bacteria strains that, because of their strong abilities to produce and tolerate high concentrations of acetic acid, have been widely used to brew vinegar in China. To globally understand the fermentation characteristics, acid-tolerant mechanisms and genetic stabilities, their genomes were sequenced. Genomic comparisons with 9 other sequenced Ap strains revealed that their chromosomes were evolutionarily conserved, whereas the plasmids were unique compared with other Ap strains. Analysis of the acid-tolerant metabolic pathway at the genomic level indicated that the metabolism of some amino acids and the known mechanisms of acetic acid tolerance, might collaboratively contribute to acetic acid resistance in Ap strains. The balance of instability factors and stability factors in the genomes of Ap CICC 20001 and CGMCC 1.41 strains might be the basis for their genetic stability, consistent with their stable industrial performances. These observations provide important insights into the acid resistance mechanism and the genetic stability of Ap strains and lay a foundation for future genetic manipulation and engineering of these two strains.

Global insights into acetic acid resistance mechanisms and genetic stability of Acetobacter pasteurianus strains by comparative genomics.

PubMed

Wang, Bin; Shao, Yanchun; Chen, Tao; Chen, Wanping; Chen, Fusheng

2015-12-22

Acetobacter pasteurianus (Ap) CICC 20001 and CGMCC 1.41 are two acetic acid bacteria strains that, because of their strong abilities to produce and tolerate high concentrations of acetic acid, have been widely used to brew vinegar in China. To globally understand the fermentation characteristics, acid-tolerant mechanisms and genetic stabilities, their genomes were sequenced. Genomic comparisons with 9 other sequenced Ap strains revealed that their chromosomes were evolutionarily conserved, whereas the plasmids were unique compared with other Ap strains. Analysis of the acid-tolerant metabolic pathway at the genomic level indicated that the metabolism of some amino acids and the known mechanisms of acetic acid tolerance, might collaboratively contribute to acetic acid resistance in Ap strains. The balance of instability factors and stability factors in the genomes of Ap CICC 20001 and CGMCC 1.41 strains might be the basis for their genetic stability, consistent with their stable industrial performances. These observations provide important insights into the acid resistance mechanism and the genetic stability of Ap strains and lay a foundation for future genetic manipulation and engineering of these two strains.

Magnet Design Considerations for Fusion Nuclear Science Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhai, Y.; Kessel, C.; El-Guebaly, L.

2016-06-01

The Fusion Nuclear Science Facility (FNSF) is a nuclear confinement facility that provides a fusion environment with components of the reactor integrated together to bridge the technical gaps of burning plasma and nuclear science between the International Thermonuclear Experimental Reactor (ITER) and the demonstration power plant (DEMO). Compared with ITER, the FNSF is smaller in size but generates much higher magnetic field, i.e., 30 times higher neutron fluence with three orders of magnitude longer plasma operation at higher operating temperatures for structures surrounding the plasma. Input parameters to the magnet design from system code analysis include magnetic field of 7.5more » T at the plasma center with a plasma major radius of 4.8 m and a minor radius of 1.2 m and a peak field of 15.5 T on the toroidal field (TF) coils for the FNSF. Both low-temperature superconductors (LTS) and high-temperature superconductors (HTS) are considered for the FNSF magnet design based on the state-of-the-art fusion magnet technology. The higher magnetic field can be achieved by using the high-performance ternary restacked-rod process Nb3Sn strands for TF magnets. The circular cable-in-conduit conductor (CICC) design similar to ITER magnets and a high-aspect-ratio rectangular CICC design are evaluated for FNSF magnets, but low-activation-jacket materials may need to be selected. The conductor design concept and TF coil winding pack composition and dimension based on the horizontal maintenance schemes are discussed. Neutron radiation limits for the LTS and HTS superconductors and electrical insulation materials are also reviewed based on the available materials previously tested. The material radiation limits for FNSF magnets are defined as part of the conceptual design studies for FNSF magnets.« less

Magnet design considerations for Fusion Nuclear Science Facility

DOE PAGES

Zhai, Yuhu; Kessel, Chuck; El-guebaly, Laila; ...

2016-02-25

The Fusion Nuclear Science Facility (FNSF) is a nuclear confinement facility to provide a fusion environment with components of the reactor integrated together to bridge the technical gaps of burning plasma and nuclear science between ITER and the demonstration power plant (DEMO). Compared to ITER, the FNSF is smaller in size but generates much higher magnetic field, 30 times higher neutron fluence with 3 orders of magnitude longer plasma operation at higher operating temperatures for structures surrounding the plasma. Input parameters to the magnet design from system code analysis include magnetic field of 7.5 T at the plasma center withmore » plasma major radius of 4.8 m and minor radius of 1.2 m, and a peak field of 15.5 T on the TF coils for FNSF. Both low temperature superconductor (LTS) and high temperature superconductor (HTS) are considered for the FNSF magnet design based on the state-of-the-art fusion magnet technology. The higher magnetic field can be achieved by using the high performance ternary Restack Rod Process (RRP) Nb3Sn strands for toroidal field (TF) magnets. The circular cable-in-conduit conductor (CICC) design similar to ITER magnets and a high aspect ratio rectangular CICC design are evaluated for FNSF magnets but low activation jacket materials may need to be selected. The conductor design concept and TF coil winding pack composition and dimension based on the horizontal maintenance schemes are discussed. Neutron radiation limits for the LTS and HTS superconductors and electrical insulation materials are also reviewed based on the available materials previously tested. As a result, the material radiation limits for FNSF magnets are defined as part of the conceptual design studies for FNSF magnets.« less

Short initial length quench on CICC of ITER TF coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nicollet, S.; Ciazynski, D.; Duchateau, J.-L.

Previous quench studies performed for the International Thermonuclear Experimental Reactor (ITER) Toroidal Field (TF) Coils have led to identify two extreme families of quench: first 'severe' quenches over long initial lengths in high magnetic field, and second smooth quenches over short initial lengths in low field region. Detailed analyses and results on smooth quench propagation and detectability on one TF Cable In Conduit Conductor (CICC) with a lower propagation velocity are presented here. The influence of the initial quench energy is shown and results of computations with either a Fast Discharge (FD) of the magnet or without (failure of themore » voltage quench detection system) are reported. The influence of the central spiral of the conductor on the propagation velocity is also detailed. In the cases of a regularly triggered FD, the hot spot temperature criterion of 150 K (with helium and jacket) is fulfilled for an initial quench length of 1 m, whereas this criterion is exceed (Tmax ≈ 200 K) for an extremely short length of 5 cm. These analyses were carried out using both the Supermagnet(trade mark, serif) and Venecia codes and the comparisons of the results are also discussed.« less

Directed evolution improves the fibrinolytic activity of nattokinase from Bacillus natto.

PubMed

Yongjun, Cai; Wei, Bao; Shujun, Jiang; Meizhi, Weng; Yan, Jia; Yan, Yin; Zhongliang, Zheng; Goulin, Zou

2011-12-01

Nattokinase (subtilisin NAT, NK) is a relatively effective microbial fibrinolytic enzyme that has been identified and characterized from Bacillus natto. In the current report, DNA family shuffling was used to improve the fibrinolytic activity of nattokinase. Three homologous genes from B. natto AS 1.107, Bacillus amyloliquefaciens CICC 20164 and Bacillus licheniformis CICC 10092 were shuffled to generate a mutant library. A plate-based method was used to screen the mutant libraries for improved activity. After three rounds of DNA shuffling, one desirable mutant with 16 amino acid substitutions was obtained. The mutant enzyme was purified and characterized. The kinetic measurements showed that the catalytic efficiency of the mutant NK was approximately 2.3 times higher than that of the wild-type nattokinase. In addition, the molecular modeling analysis suggested that the mutations affect the enzymatic function by changing the surface conformation of the substrate-binding pocket. The current study shows that the evolution of nattokinase with improved fibrinolytic activity by DNA family shuffling is feasible and provides useful references to facilitate the application of nattokinase in thrombolytic therapy. © 2011 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

Global insights into acetic acid resistance mechanisms and genetic stability of Acetobacter pasteurianus strains by comparative genomics

PubMed Central

Wang, Bin; Shao, Yanchun; Chen, Tao; Chen, Wanping; Chen, Fusheng

2015-01-01

Acetobacter pasteurianus (Ap) CICC 20001 and CGMCC 1.41 are two acetic acid bacteria strains that, because of their strong abilities to produce and tolerate high concentrations of acetic acid, have been widely used to brew vinegar in China. To globally understand the fermentation characteristics, acid-tolerant mechanisms and genetic stabilities, their genomes were sequenced. Genomic comparisons with 9 other sequenced Ap strains revealed that their chromosomes were evolutionarily conserved, whereas the plasmids were unique compared with other Ap strains. Analysis of the acid-tolerant metabolic pathway at the genomic level indicated that the metabolism of some amino acids and the known mechanisms of acetic acid tolerance, might collaboratively contribute to acetic acid resistance in Ap strains. The balance of instability factors and stability factors in the genomes of Ap CICC 20001 and CGMCC 1.41 strains might be the basis for their genetic stability, consistent with their stable industrial performances. These observations provide important insights into the acid resistance mechanism and the genetic stability of Ap strains and lay a foundation for future genetic manipulation and engineering of these two strains. PMID:26691589

Wickerhamomyces mori sp. nov., an anamorphic yeast species found in the guts of wood-boring insect larvae.

PubMed

Hui, Feng-Li; Chen, Liang; Chu, Xue-Ying; Niu, Qiu-Hong; Ke, Tao

2013-03-01

A novel anamorphic yeast species is described to accommodate three isolates recovered from the guts of three different wood-boring insect larvae collected in Henan, central China. On the basis of sequence analyses of the D1/D2 domains of the large-subunit rRNA gene and the internal transcribed spacer regions, the three strains are assigned to a novel species of the genus Wickerhamomyces, although the formation of ascospores was not observed. These strains also exhibited a number of distinct morphological and physiological characteristics that clearly differentiated them from Wickerhamomyces mucosus, Candida odintsovae and Wickerhamomyces rabaulensis, the most closely related species. In view of the phenotypic differences and unique rRNA gene sequences, we consider that these three isolates represent a novel species of the genus Wickerhamomyces, Wickerhamomyces mori sp. nov. The type strain is NYNU 1216(T) ( = CICC 1983(T)  = CBS 12678(T)).

Candida baotianmanensis sp. nov. and Candida pseudoviswanathii sp. nov., two ascosporic yeast species isolated from the gut of beetles.

PubMed

Ren, Yong-Cheng; Xu, Long-Long; Zhang, Lin; Hui, Feng-Li

2015-10-01

Four yeast strains were isolated from the gut of beetles collected on Baotianman Mountain and People's Park of Nanyang in Henan Province, China. These strains produced unconjugated asci with one or two ellipsoidal to elongate ascospores in a persistent ascus. Phylogenetic analysis of the D1/D2 domains of the LSU rRNA gene sequences indicated that the isolates represent two novel sexual species in the Candida/Lodderomyces clade. Candida baotianmanensis sp. nov. was located in a statistically well-supported branch together with Candida maltosa. Candida pseudoviswanathii sp. nov. formed a subclade with its closest relative Candida viswanathii supported by a strong bootstrap value. The two novel species were distinguished from their most closely related described species, Candida maltosa and Candida viswanathii, in the D1/D2 LSU rRNA gene and internal transcribed spacer (ITS) sequences and in phenotypic traits. The type strain of Candida baotianmanensis sp. nov. is NYNU 14719T ( = CBS 13915T = CICC 33052T), and the type strain of Candida pseudoviswanathii sp. nov. is NYNU 14772T ( = CBS 13916T = CICC 33053T). The MycoBank numbers for Candida baotianmanensis sp. nov. and Candida pseudoviswanathii sp. nov. are MB 812621 and MB 812622.

Cold work study on a 316LN modified alloy for the ITER TF coil conduit

DOE PAGES

Walsh, Robert; Toplosky, V. J.; McRae, D. M.; ...

2012-06-01

The primary structural component of the cable-in-conduit conductor (CICC) magnets, such as the ITER TF coils is the conduit. This function creates requirements for 4 K strength, toughness, fatigue crack resistance, and ductility after exposure to the superconductor's reaction heat treatment. The tensile ductility of a steel is a quality factor related to fatigue and fracture resistance that can be evaluated more economically with tensile tests rather than fatigue and fracture tests. We subject 316LN modified base metal and welds to a range of cold work from 0% to 20% and a subsequent Nb 3Sn reaction heat treatment to evaluatemore » the effects on the tensile properties. With the addition of cold work, the 4 K yield strength increases while tensile elongation decreases in both the base metal and weld. Our results are compared to previously published data on the same alloy to evaluate the use of tensile ductility parameters as a materials qualification specification in magnet design.« less

Candida sanyaensis sp. nov., an ascomycetous yeast species isolated from soil.

PubMed

Hui, Feng-Li; Niu, Qiu-Hong; Ke, Tao; Li, Ying-Xia; Lee, Ching-Fu

2013-01-01

Strains representing a novel ascomycetous yeast species, Candida sanyaensis, were isolated from soil samples collected on Hainan Island and Taiwan Island in China. Analysis of the D1/D2 domains of the large subunit (LUS) rRNA gene and internal transcribed spacer (ITS) regions of these strains showed that this species was related to Candida tropicalis and Candida sojae, their closest relatives. C. sanyaensis differed by three substitutions and one gap from C. tropicalis, and by four substitutions and one gap from C. sojae, in the D1/D2 domain sequences. However, the ITS sequences of C. sanyaensis were quite divergent from the latter two species, showing that it is a genetically separate species. The novel strains were also found to have very similar PCR-fingerprinting profiles which were quite distinct from those of C. tropicalis and C. sojae strains. The type strain of C. sanyaensis is HN-26(T) (= CICC 1979(T) = CBS 12637(T)).

Candida ficus sp. nov., a novel yeast species from the gut of Apriona germari larvae.

PubMed

Hui, Feng-Li; Niu, Qiu-Hong; Ke, Tao; Liu, Zheng

2012-11-01

A novel yeast species is described based on three strains from the gut of wood-boring larvae collected in a tree trunk of Ficus carica cultivated in parks near Nanyang, central China. Phylogenetic analysis based on sequences of the D1/D2 domains of the large subunit rRNA gene showed that these strains occurred in a separate clade that was genetically distinct from all known ascomycetous yeasts. In terms of pairwise sequence divergence, the novel strains differed by 15.3% divergence from the type strain of Pichia terricola, and by 15.8% divergence from the type strains of Pichia exigua and Candida rugopelliculosa in the D1/D2 domains. All three are ascomycetous yeasts in the Pichia clade. Unlike P. terricola, P. exigua and C. rugopelliculosa, the novel isolates did not ferment glucose. The name Candida ficus sp. nov. is proposed to accommodate these highly divergent organisms, with STN-8(T) (=CICC 1980(T)=CBS 12638(T)) as the type strain.

Cryptococcus nanyangensis sp. nov., a new basidiomycetous yeast isolated from the gut of wood-boring larvae.

PubMed

Hui, Feng-Li; Niu, Qiu-Hong; Ke, Tao; Li, Ying-Xia

2012-11-01

Two strains of a novel basidiomycetous yeast species were isolated from the gut of wood-boring larvae collected in the Baotianman Nature Reserve, the central China. Sequence analysis of the D1/D2 domains of the large subunit (LSU) rRNA gene and internal transcribed spacer (ITS) regions showed that these yeasts belong to the Bulleromyces clade and formed a cluster together with eleven undescribed Cryptococcus species. The novel species differed from its closest known species, Cryptococcus rajasthanensis, by 3.3 % divergence (15 substitutions and 6 gaps over 630 bases) in the D1/D2 domains, and by 13.4 % divergence (41 substitutions and 27 gaps over 508 bases) in the ITS regions. Physiologically, the fermentation of glucose, galactose, sucrose, trehalose, and raffinose in Durham tubes was observed for the strains of this new yeast. Based on the phenotypical and molecular characteristics presented, the two strains are proposed as a new species, Cryptococcus nanyangensis sp. nov., with the type strain KCY-1(T) (=CICC 1976(T) = CBS 12474(T)).

Production of C4 and C5 branched-chain alcohols by engineered Escherichia. coli.

PubMed

Chen, Xiaoyan; Xu, Jingliang; Yang, Liu; Yuan, Zhenhong; Xiao, Shiyuan; Zhang, Yu; Liang, Cuiyi; He, Minchao; Guo, Ying

2015-11-01

Higher alcohols, longer chain alcohols, contain more than 3 carbon atoms, showed close energy advantages as gasoline, and were considered as the next generation substitution for chemical fuels. Higher alcohol biosynthesis by native microorganisms mainly needs gene expression of heterologous keto acid decarboxylase and alcohol dehydrogenases. In the present study, branched-chain α-keto acid decarboxylase gene from Lactococcus lactis subsp. lactis CICC 6246 (Kivd) and alcohol dehydrogenases gene from Zymomonas mobilis CICC 41465 (AdhB) were transformed into Escherichia coli for higher alcohol production. SDS-PAGE results showed these two proteins were expressed in the recombinant strains. The resulting strain was incubated in LB medium at 37 °C in Erlenmeyer flasks and much more 3-methyl-1-butanol (104 mg/L) than isobutanol (24 mg/L) was produced. However, in 5 g/L glucose-containing medium, the production of two alcohols was similar, 156 and 161 mg/L for C4 (isobutanol) and C5 (3-methyl-1-butanol) alcohol, respectively. Effects of fermentation factors including temperature, glucose content, and α-keto acid on alcohol production were also investigated. The increase of glucose content and the adding of α-keto acids facilitated the production of C4 and C5 alcohols. The enzyme activities of pure Kivd on α-ketoisovalerate and α-ketoisocaproate were 26.77 and 21.24 μmol min(-1) mg(-1), respectively. Due to its ability on decarboxylation of α-ketoisovalerate and α-ketoisocaproate, the recombinant E. coli strain showed potential application on isoamyl alcohol and isobutanol production.

Candida funiuensi sp. nov., a cellobiose-fermenting yeast species isolated from rotten wood.

PubMed

Wang, Yun; Ren, Yong-Cheng; Zhang, Zheng-Tian; Wu, Fu-Hua; Ke, Tao; Hui, Feng-Li

2015-06-01

Two strains of an asexual cellobiose-fermenting yeast species were isolated from rotten wood samples collected in Funiu Mountain Nature Reserve in Henan Province, central China. Molecular phylogenetic analysis that included the nearly complete small subunit (SSU), the internal transcribed spacer (ITS) region and the D1/D2 domains of the large subunit (LSU) rDNA showed that these strains belonged to the Candida kruisii clade, with Candida kruisii and Candida cretensis as their closest phylogenetic neighbours. The nucleotide differences between the novel strains and the type strains of C. kruisii and C. cretensis were 30 and 36 substitutions, respectively, in the D1/D2 LSU rDNA, 40 and 44 substitutions, respectively, in the ITS region and 19 and 23 substitutions, respectively, in the SSU rDNA. The novel strains can also be distinguished from their closest described species, C. kruisii and C. cretensis, by a number of physiological characteristics, and represent a novel species of the genus Candida, for which the name Candida funiuensis sp. nov. is proposed. The type strain is NYNU 14625T ( = CICC 33050T = CBS 13911T). The Mycobank number is MB 811503.

Critical currents of Nb sub 3 Sn wires for the US-DPC coil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takayasu, M.; Gung, C.Y.; Steeves, M.M.

1991-03-01

This paper evaluates the critical current of titanium-alloyed internal-tin, jelly-roll Nb{sub 3}Sn wire for use in the US-DPC coil. It was confirmed from 14 randomly-selected samples that the critical-current values were uniform and consistent: the non-copper critical-current density was approximately 700 A/mm{sup 2} at 10 T and 4.2 K in agreement with expectations. A 27-strand cable-in-conduit conductor (CICC) using the low-thermal-coefficient-of-expansion superalloy Incoloy 905 yielded a critical current 5--7% below the average value of the single-strand data.

New remarkable records of microfungi from Sardinia (Italy).

PubMed

Jensen, M; Nerat, N; Ale-Agha, N

2010-01-01

In June 2009 we organized a botanical student excursion to the eastern part of Sardinia, Italy. On this occasion we were able to collect and identify over 80 species of microfungi growing on higher plants. The collecting sites were spread over a large area, among them were La Caletta, Capo Comino, Monte Albo, Cala Gonone, Monte Maccione, San Teodoro, Capo Testa. The collected microfungi were parasitic or saprophytic; Basidiomycotina (Uredinales), Ascomycotina and Deuteromycotina (Hyphomycetes, Coelomycetes) were predominant. Examples are Pezicula corticola (Jörg.) NANNF. (new for Sardinia), on Pyrus communis. Puccinia chamaecyparissi TROTT. (new for Sardinia), on Santolina insularis. Sphaceloma oleae CICC. and GRANITI (new for Sardinia) and Phlyctema vagabunda DESM. (new for Sardinia), on Olea europaea and Arbutus unedo. Puccinia pseudosphaeria MONT. (new for Sardinia), on Sonchus oleraceus. Discula umbrinella (BERK. and BR.) SUTTON (new for Sardinia)(D. quercina WEST. and BARK), on Quercus coccifera. Zaghouania phillyreae PAT. (new for Sardinia), on Phillyrea angustifolia. Phymatotrichum omnivorum (DUGGAR) HENNEBERT, new on Verbascum thapsus for Sardinia. Guignardia punctoidea (COOKE) SCHROTER (new for Sardinia), on Quercus ilex. Many of the collected species are rare or unknown for the area of investigation until now. All specimens are located in the Herbarium ESS, Mycotheca Parva collection G.B. Feige and N. Ale-Agha.

Direct Ethanol Production from Lignocellulosic Sugars and Sugarcane Bagasse by a Recombinant Trichoderma reesei Strain HJ48

PubMed Central

Huang, Jun; Chen, Dong; Wei, Yutuo; Wang, Qingyan; Li, Zhenchong; Chen, Ying; Huang, Ribo

2014-01-01

Trichoderma reesei can be considered as a candidate for consolidated bioprocessing (CBP) microorganism. However, its ethanol yield needs to be improved significantly. Here the ethanol production of T. reesei CICC 40360 was improved by genome shuffling while simultaneously enhancing the ethanol resistance. The initial mutant population was generated by nitrosoguanidine treatment of the spores, and an improved population producing more than fivefold ethanol than wild type was obtained by genome shuffling. The results show that the shuffled strain HJ48 can efficiently convert lignocellulosic sugars to ethanol under aerobic conditions. Furthermore, it was able to produce ethanol directly from sugarcane bagasse, demonstrating that the shuffled strain HJ48 is a suitable microorganism for consolidated bioprocessing. PMID:24995362

Direct ethanol production from lignocellulosic sugars and sugarcane bagasse by a recombinant Trichoderma reesei strain HJ48.

PubMed

Huang, Jun; Chen, Dong; Wei, Yutuo; Wang, Qingyan; Li, Zhenchong; Chen, Ying; Huang, Ribo

2014-01-01

Trichoderma reesei can be considered as a candidate for consolidated bioprocessing (CBP) microorganism. However, its ethanol yield needs to be improved significantly. Here the ethanol production of T. reesei CICC 40360 was improved by genome shuffling while simultaneously enhancing the ethanol resistance. The initial mutant population was generated by nitrosoguanidine treatment of the spores, and an improved population producing more than fivefold ethanol than wild type was obtained by genome shuffling. The results show that the shuffled strain HJ48 can efficiently convert lignocellulosic sugars to ethanol under aerobic conditions. Furthermore, it was able to produce ethanol directly from sugarcane bagasse, demonstrating that the shuffled strain HJ48 is a suitable microorganism for consolidated bioprocessing.

Influence of the magnetic field profile on ITER conductor testing

NASA Astrophysics Data System (ADS)

Nijhuis, A.; Ilyin, Y.; ten Kate, H. H. J.

2006-08-01

We performed simulations with the numerical CUDI-CICC code on a typical short ITER (International Thermonuclear Experimental Reactor) conductor test sample of dual leg configuration, as usually tested in the SULTAN test facility, and made a comparison with the new EFDA-Dipole test facility offering a larger applied DC field region. The new EFDA-Dipole test facility, designed for short sample testing of conductors for ITER, has a homogeneous high field region of 1.2 m, while in the SULTAN facility this region is three times shorter. The inevitable non-uniformity of the current distribution in the cable, introduced by the joints at both ends, has a degrading effect on voltage-current (VI) and voltage-temperature (VT) characteristics, particularly for these short samples. This can easily result in an underestimation or overestimation of the actual conductor performance. A longer applied DC high field region along a conductor suppresses the current non-uniformity by increasing the overall longitudinal cable electric field when reaching the current sharing mode. The numerical interpretation study presented here gives a quantitative analysis for a relevant practical case of a test of a short sample poloidal field coil insert (PFCI) conductor in SULTAN. The simulation includes the results of current distribution analysis from self-field measurements with Hall sensor arrays, current sharing measurements and inter-petal resistance measurements. The outcome of the simulations confirms that the current uniformity improves with a longer high field region but the 'measured' VI transition is barely affected, though the local peak voltages become somewhat suppressed. It appears that the location of the high field region and voltage taps has practically no influence on the VI curve as long as the transverse voltage components are adequately cancelled. In particular, for a thin conduit wall, the voltage taps should be connected to the conduit in the form of an (open) azimuthally soldered wire, averaging the transverse conduit surface potentials initiated in the joints.

A Comparative Study of Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds

NASA Astrophysics Data System (ADS)

Aviles Santillana, I.; Boyer, C.; Fernandez Pison, P.; Foussat, A.; Langeslag, S. A. E.; Perez Fontenla, A. T.; Ruiz Navas, E. M.; Sgobba, S.

2018-03-01

The ITER magnet system is based on the "cable-in-conduit" conductor (CICC) concept, which consists of stainless steel jackets filled with superconducting strands. The jackets provide high strength, limited fatigue crack growth rate and fracture toughness properties to counteract the high stress imposed by, among others, electromagnetic loads at cryogenic temperature. Austenitic nitrogen-strengthened stainless steels have been chosen as base material for the jackets of the central solenoid and the toroidal field system, for which an extensive set of cryogenic mechanical property data are readily available. However, little is published for their welded joints, and their specific performance when considering different combinations of parent and filler metals. Moreover, the impact of post-weld heat treatments that are required for Nb3Sn formation is not extensively treated. Welds are frequently responsible for cracks initiated and propagated by fatigue during service, causing structural failure. It becomes thus essential to select the most suitable combination of parent and filler material and to assess their performance in terms of strength and crack propagation at operation conditions. An extensive test campaign has been conducted at 7 K comparing tungsten inert gas (TIG) welds using two fillers adapted to cryogenic service, EN 1.4453 and JK2LB, applied to two different base metals, AISI 316L and 316LN. A large set of fracture toughness data are presented, and the detrimental effect on fracture toughness of post-weld heat treatments (unavoidable for some of the components) is demonstrated. In this study, austenitic stainless steel TIG welds with various filler metals have undergone a comprehensive fracture mechanics characterization at 7 K. These results are directly exploitable and contribute to the cryogenic fracture mechanics properties database of the ITER magnet system. Additionally, a correlation between the impact in fracture toughness and microstructure resulting from the above treatment is provided.

Current leads cooling for the series-connected hybrid magnets

NASA Astrophysics Data System (ADS)

Bai, Hongyu; Marshall, William S.; Bird, Mark D.; Gavrilin, Andrew V.; Weijers, Hubertus W.

2014-01-01

Two Series-Connected Hybrid (SCH) magnets are being developed at the National High Magnetic Field Laboratory. Both SCH magnets combine a set of resistive Florida-Bitter coils with a superconducting outsert coil constructed of the cable-in-conduit conductor (CICC). The outsert coils of the two magnets employ 20 kA BSCCO HTS current leads for the power supply although they have different designs and cooling methods. The copper heat exchangers of the HTS current leads for the HZB SCH are cooled with forced flow helium at a supply temperature of 44 K, while the copper heat exchangers of HTS current leads for NHMFL SCH are cooled with liquid nitrogen at a temperature of 78 K in a self-demand boil-off mode. This paper presents the two cooling methods and their impacts on cryogenic systems. Their efficiencies and costs are compared and presented.

Power supply system for the superconducting outsert of the CHMFL hybrid magnet

NASA Astrophysics Data System (ADS)

Fang, Z.; Zhu, J.; Chen, W.; Jiang, D.; Huang, P.; Chen, Z.; Tan, Y.; Kuang, G.

2017-12-01

The construction of a new hybrid magnet, consisting of a 11 T superconducting outsert and a 34 T resistive insert magnet, has been finished at the Chinese High Magnetic Field Laboratory (CHMFL) in Hefei. With a room temperature bore of 800 mm in diameter, the hybrid magnet superconducting outsert is composed of four separate Nb3Sn-based Cable-in-Conduit Conductor (CICC) coils electrically connected in series and powered by a single power supply system. The power supply system for the superconducting outsert consists of a 16 kA DC power supply, a quench protection system, a pair of 16 kA High Temperature Superconducting (HTS) current leads, and two Low Temperature Superconducting bus-lines. The design and manufacturing of the power supply system have been completed at the CHMFL. This paper describes the design features of the power supply system as well as the current fabrication condition of its main components.

Serratia bozhouensis sp. nov., Isolated from Sewage Samples of a Dairy Farm.

PubMed

Shang, Fei; Xue, Ting; Wang, Man; Chen, Xiaolin; Yu, Li; Zhang, Ming

2017-07-01

A Gram-negative, rod-shaped, salt-tolerant, non-pigmented, and non-spore-forming bacterium, designated strain W1 T (type strain CICC 23797 = CGMCC1.14949), was isolated from sewage samples of a dairy farm in Bozhou, Anhui, China. Strain W1 was resistant to lincomycin, troleandomycin, rifamycin, and vancomycin. Sequence analysis of the 16S rDNA gene revealed that the strain showed sequence similarity of 98.2% with the closest related species Serratia quinivorans CP6a T . The genomic DNA G+C content of the isolate was 52.8 mol%. The biochemical characteristics of strain W1 T assessed by the API 20E and Biolog GEN III analysis were different from those of the members of the genus Serratia. On the basis of the phenotypic and genotypic differences, strain W1 was proposed to be a novel Serratia species, Serratia bozhouensis sp. nov W1 T .

Challenges and status of ITER conductor production

NASA Astrophysics Data System (ADS)

Devred, A.; Backbier, I.; Bessette, D.; Bevillard, G.; Gardner, M.; Jong, C.; Lillaz, F.; Mitchell, N.; Romano, G.; Vostner, A.

2014-04-01

Taking the relay of the large Hadron collider (LHC) at CERN, ITER has become the largest project in applied superconductivity. In addition to its technical complexity, ITER is also a management challenge as it relies on an unprecedented collaboration of seven partners, representing more than half of the world population, who provide 90% of the components as in-kind contributions. The ITER magnet system is one of the most sophisticated superconducting magnet systems ever designed, with an enormous stored energy of 51 GJ. It involves six of the ITER partners. The coils are wound from cable-in-conduit conductors (CICCs) made up of superconducting and copper strands assembled into a multistage cable, inserted into a conduit of butt-welded austenitic steel tubes. The conductors for the toroidal field (TF) and central solenoid (CS) coils require about 600 t of Nb3Sn strands while the poloidal field (PF) and correction coil (CC) and busbar conductors need around 275 t of Nb-Ti strands. The required amount of Nb3Sn strands far exceeds pre-existing industrial capacity and has called for a significant worldwide production scale up. The TF conductors are the first ITER components to be mass produced and are more than 50% complete. During its life time, the CS coil will have to sustain several tens of thousands of electromagnetic (EM) cycles to high current and field conditions, way beyond anything a large Nb3Sn coil has ever experienced. Following a comprehensive R&D program, a technical solution has been found for the CS conductor, which ensures stable performance versus EM and thermal cycling. Productions of PF, CC and busbar conductors are also underway. After an introduction to the ITER project and magnet system, we describe the ITER conductor procurements and the quality assurance/quality control programs that have been implemented to ensure production uniformity across numerous suppliers. Then, we provide examples of technical challenges that have been encountered and we present the status of ITER conductor production worldwide.

Improved Ethanol Production from Xylose by Candida shehatae Induced by Dielectric Barrier Discharge Air Plasma

NASA Astrophysics Data System (ADS)

Chen, Huixia; Xiu, Zhilong; Bai, Fengwu

2014-06-01

Xylose fermentation is essential for ethanol production from lignocellulosic biomass. Exposure of the xylose-fermenting yeast Candida shehatae (C. shehatae) CICC1766 to atmospheric pressure dielectric barrier discharge (DBD) air plasma yields a clone (designated as C81015) with stability, which exhibits a higher ethanol fermentation rate from xylose, giving a maximal enhancement in ethanol production of 36.2% compared to the control (untreated). However, the biomass production of C81015 is lower than that of the control. Analysis of the NADH (nicotinamide adenine dinucleotide)- and NADPH (nicotinamide adenine dinucleotide phosphate)-linked xylose reductases and NAD+-linked xylitol dehydrogenase indicates that their activities are enhanced by 34.1%, 61.5% and 66.3%, respectively, suggesting that the activities of these three enzymes are responsible for improving ethanol fermentation in C81015 with xylose as a substrate. The results of this study show that DBD air plasma could serve as a novel and effective means of generating microbial strains that can better use xylose for ethanol fermentation.

Wickerhamiella allomyrinae f.a., sp. nov., a yeast species isolated from the gut of the rhinoceros beetle Allomyrina dichotoma.

PubMed

Ren, Yong-Cheng; Wang, Yun; Chen, Liang; Ke, Tao; Hui, Feng-Li

2014-11-01

Two strains representing Wickerhamiella allomyrinae f.a., sp. nov. were isolated from the gut of Allomyrina dichotoma (Coleoptera: Scarabeidae) collected from the Baotianman National Nature Reserve, Nanyan, Henan Province, China. Sequence analyses of the D1/D2 domains of the LSU rRNA gene revealed that this novel species was located in the Wickerhamiella clade (Saccharomycetes, Saccharomycetales), with three described species of the genus Candida, namely Candida musiphila, Candida spandovensis and Candida sergipensis, as the most closely related species. The novel species differed from these three species by 9.3-9.8% sequence divergence (35-45 nt substitutions) in the D1/D2 sequences. The species could also be distinguished from the closely related species, C. musiphila, C. spandovensis and C. sergipensis, by growth on vitamin-free medium and at 37 °C. The type strain is Wickerhamiella allomyrinae sp. nov. NYNU 13920(T) ( =CICC 33031(T) =CBS 13167(T)). © 2014 IUMS.

Aquamicrobium terrae sp. nov., isolated from the polluted soil near a chemical factory.

PubMed

Wu, Zhi-Guo; Wang, Fang; Gu, Cheng-Gang; Zhang, Yin-Ping; Yang, Zong-Zheng; Wu, Xiao-Wei; Jiang, Xin

2014-06-01

A Gram-negative, aerobic, non-motile bacterial strain hun6(T) isolated from the polluted soil near a chemical factory in northern Nanjing, China was investigated to clarify its taxonomic position. Growth of strain hun6(T) occurred between 10 and 45 °C (optimum, 30 °C) and between pH 6.0 and 8.0 (optimum, pH 7.0). No growth occurred at NaCl concentrations greater than 5 % (w/v). The 16S rRNA gene sequence analysis indicated that strain hun6(T) belongs to the genus Aquamicrobium. The sequence similarities of strain hun6(T) to other type strains of Aquamicrobium genus were all below 98.5 %. The presence of ubiquinone-10, the predominant fatty acid summed feature 8 (C18:1 ω7c and/or C18:1 ω6c) and C19:0 cyclo ω8c, a polar lipid pattern with phosphatidylglycerol, phosphatidylcholine, diphosphatidylglycerol, phosphatidylethanolamine and phophatidylmonomethylethanoamine were in accord with the characteristics of the genus Aquamicrobium. The G+C content of the genomic DNA was determined to be 63.5 mol%. The results of DNA-DNA hybridization, physiological and biochemical tests and chemotaxonomic properties allowed genotypic and phenotypic differentiation of strain hun6(T) from all known Aquamicrobium species. Therefore, strain hun6(T) can be assigned to a new species of this genus for which the name Aquamicrobium terrae sp. nov. is proposed. The type strain is hun6(T) (= CICC 10733(T) = DSM 27865(T)).

Using the CRISPR/Cas9 system to eliminate native plasmids of Zymomonas mobilis ZM4.

PubMed

Cao, Qing-Hua; Shao, Huan-Huan; Qiu, Hui; Li, Tao; Zhang, Yi-Zheng; Tan, Xue-Mei

2017-03-01

The CRISPR/Cas system can be used to simply and efficiently edit the genomes of various species, including animals, plants, and microbes. Zymomonas mobilis ZM4 is a highly efficient, ethanol-producing bacterium that contains five native plasmids. Here, we constructed the pSUZM2a-Cas9 plasmid and a single-guide RNA expression plasmid. The pSUZM2a-Cas9 plasmid was used to express the Cas9 gene cloned from Streptococcus pyogenes CICC 10464. The single-guide RNA expression plasmid pUC-T7sgRNA, with a T7 promoter, can be used for the in vitro synthesis of single-guide RNAs. This system was successfully employed to knockout the upp gene of Escherichia coli and the replicase genes of native Z. mobilis plasmids. This is the first study to apply the CRISPR/Cas9 system of S. pyogenes to eliminate native plasmids in Z. mobilis. It provides a new method for plasmid curing and paves the way for the genomic engineering of Z. mobilis.

Roseimarinus sediminis gen. nov., sp. nov., a facultatively anaerobic bacterium isolated from coastal sediment.

PubMed

Wu, Wen-Jie; Liu, Qian-Qian; Chen, Guan-Jun; Du, Zong-Jun

2015-07-01

A Gram-stain-negative, facultatively anaerobic, non-motile and pink-pigmented bacterium, designated strain HF08(T), was isolated from marine sediment of the coast of Weihai, China. Cells were rod-shaped, and oxidase- and catalase-positive. The isolate grew optimally at 33 °C, at pH 7.5-8.0 and with 2-3% (w/v) NaCl. The dominant cellular fatty acids were iso-C15 : 0, anteiso-C15 : 0 and iso-C14 : 0. Menaquinone 7 (MK-7) was the major respiratory quinone and the DNA G+C content was 44.8 mol%. Phylogenetic analysis based on 16S rRNA gene sequences revealed that the isolate was a member of the class Bacteroidia, and shared 88-90% sequence similarity with the closest genera Sunxiuqinia, Prolixibacter, Draconibacterium, Mariniphaga and Meniscus. Based on the phylogenetic and phenotypic evidence presented, a novel species in a new genus of the family Prolixibacteraceae is proposed, with the name Roseimarinus sediminis gen. nov., sp. nov. The type strain of Roseimarinus sediminis is HF08(T) ( = KCTC 42261(T) = CICC 10901(T)).

Research on Identification and Screen of Microbial Desulfurization Strains for Petroleum

NASA Astrophysics Data System (ADS)

Xiaojuan, Tian; Lingtian, Tang; Li'e, Peng; Xinghong, Li

The oil-contaminated soil sample was acquired from Shengli Oilfield and Jidong Oilfield and cultured with enrichment technology. Then 21 desulfurization strains were separated from the sample, from which a high efficiency desulfurization strain TV9704 was selected. The strain could neither grow with n-dodecane, n-hexadecane, liquid paraffin, naphthalene or diesel as a carbon source and energy source, nor obviously reduce oil combustion value. It could use thiophene or dibenzothiophene (DBT) as the sole sulfur source. In the experiment, the concentrations of thiophene and DBT were measured by UV spectrophotometer. After being cultured in the culture medium with an initial concentration of 63.2 mmol/L respectively for 48 h and 144 h, the degradation rates of the strain TV9704 on thiophene were 39.0% and 63.8%; the DBT with an initial concentration of 2.7 mmol/L was degraded by 1.46 mmol/L after cultured for 72 h. When sodium acetate and glycerol were chosen as carbon source, the ethanol could enhance the degradation rate of TV9704 on DBT significantly. Strain TV9704 was identified by China Industrial Culture Collection Center (CICC) as a Bacillus sp., Gram-positive, obligate aerobic, which forms a circular orange colony on the nutrition gravy plate. The 16SrDNA gene sequencing test and analysis was carried out on strain TV9704, finding that its homologies with the most similar species Bacillus aquimaris and Bacillus marisflavi were 99.2% and 98.2% respectively, but a larger difference existed between their cell morphological characteristics and physiological and biochemical characteristics, therefore strain TV9704 may be a new species because it was impossible to be categorized to any population.

A 32 kb 9T near-threshold SRAM with enhanced read ability at ultra-low voltage operation

NASA Astrophysics Data System (ADS)

Kim, Tony Tae-Hyoung; Lee, Zhao Chuan; Do, Anh Tuan

2018-01-01

Ultra-low voltage SRAMs are highly sought-after in energy-limited systems such as battery-powered and self-harvested SoCs. However, ultra-low voltage operation diminishes SRAM read bitline (RBL) sensing margin significantly. This paper tackles this issue by presenting a novel 9T cell with data-independent RBL leakage in combination with an RBL boosting technique for enhancing the sensing margin. The proposed technique automatically tracks process, temperature and voltage (PVT) variations for robust sensing margin enhancement. A test chip fabricated in 65 nm CMOS technology shows that the proposed scheme significantly enlarges the sensing margin compared to the conventional bitline sensing scheme. It also achieves the minimum operating voltage of 0.18 V and the minimum energy consumption of 0.92 J/access at 0.4 V. He received 2016 International Low Power Design Contest Award from ISLPED, a best paper award at 2014 and 2011 ISOCC, 2008 AMD/CICC Student Scholarship Award, 2008 Departmental Research Fellowship from Univ. of Minnesota, 2008 DAC/ISSCC Student Design Contest Award, 2008, 2001, and 1999 Samsung Humantec Thesis Award and, 2005 ETRI Journal Paper of the Year Award. He is an author/co-author of +100 journal and conference papers and has 17 US and Korean patents registered. His current research interests include low power and high performance digital, mixed- mode, and memory circuit design, ultra-low voltage circuits and systems design, variation and aging tolerant circuits and systems, and circuit techniques for 3D ICs. He serves as an associate editor of IEEE Transactions on VLSI Systems. He is an IEEE senior member and the Chair of IEEE Solid-State Circuits Society Singapore Chapter. He has served numerous conferences as a committee member.

Purification of Lactobacillus acidophilus surface-layer protein and its immunomodulatory effects on RAW264.7 cells.

PubMed

Zhang, Dandan; Wu, Mengting; Guo, Yuxing; Xun, Mingyue; Wang, Wenwen; Wu, Zhen; Pan, Daodong

2017-09-01

Surface-layer proteins (SLP) have been found in the outermost layer of the cell wall in many types of lactobacillus are considered to be an important factor with respect to intestinal immunity. The present study compared the effects of SLP extracted by different concentrations of LiCl and carbamide, and subsequently identified by sodium dodecyl sulfate-polyacrylamide gel electrophoresis, circular dichroism and differential scanning calorimetry. Furthermore, RAW 264.7 cells were used to evaluate the immunomodulatory effects of SLP. SLP were derived from Lactobacillus acidophilus CICC6074 with a molecular weight of 46 kDa, and consisted of 16.9% α-helix, 42.3% β-sheet, 20.8% β-turns and 22.5% random coils. SLP promoted NO secretion and higher quantities of NO were produced as the SLP concentrations increased. SLP concentrations over 50 µg mL -1 significantly decreased the amount of tumor necrosis factor-α secreted by RAW264.7 cells. SLP can trigger immunomodulatory effects in RAW 264.7 cells. This provides crucial information that will enable the further use of L. acidophilus in food, medicine and other products. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Tangfeifania diversioriginum gen. nov., sp. nov., a representative of the family Draconibacteriaceae.

PubMed

Liu, Qian-Qian; Li, Xiao-Li; Rooney, Alejandro P; Du, Zong-Jun; Chen, Guan-Jun

2014-10-01

A novel Gram-stain-negative, facultatively anaerobic, catalase- and oxidase-positive, non-motile and pink-pigmented bacterium, designated G22(T), was isolated from Gahai, a saltwater lake in Qinghai province, China. Optimal growth occurred at 33-35 °C, pH 7.0-7.5, and in the presence of 2-4% (w/v) NaCl. The DNA G+C content was 40.0 mol%. The major polar lipids were phosphatidylethanolamine and three unknown lipids. The predominant cellular fatty acids were iso-C15:0, anteiso-C15:0, iso-C17:0 3-OH and iso-C15:0 3-OH, and MK-7 was the main respiratory quinone. Phylogenetic analysis based on 16S rRNA gene sequences revealed that strain G22(T) fell within the class Bacteroidia. Its closest phylogenetic neighbour was the recently described species Draconibacterium orientale, the sole member of the family Draconibacteriaceae, with merely 90.04% sequence similarity. On the basis of phenotypic, chemotaxonomic and phylogenetic evidence observed, a novel species in a new genus, Tangfeifania diversioriginum gen. nov., sp. nov., is proposed within the family Draconibacteriaceae. The type strain is G22(T) ( = CICC 10587(T) =DSM 27063(T)).

Mechanical behaviors of multi-filament twist superconducting strand under tensile and cyclic loading

NASA Astrophysics Data System (ADS)

Wang, Xu; Li, Yingxu; Gao, Yuanwen

2016-01-01

The superconducting strand, serving as the basic unit cell of the cable-in-conduit-conductors (CICCs), is a typical multi-filament twist composite which is always subjected to a cyclic loading under the operating condition. Meanwhile, the superconducting material Nb3Sn in the strand is sensitive to strain frequently relating to the performance degradation of the superconductivity. Therefore, a comprehensive study on the mechanical behavior of the strand helps understanding the superconducting performance of the strained Nb3Sn strands. To address this issue, taking the LMI (internal tin) strand as an example, a three-dimensional structural finite element model, named as the Multi-filament twist model, of the strand with the real configuration of the LMI strand is built to study the influences of the plasticity of the component materials, the twist of the filament bundle, the initial thermal residual stress and the breakage and its evolution of the filaments on the mechanical behaviors of the strand. The effective properties of superconducting filament bundle with random filament breakage and its evolution versus strain are obtained based on the damage theory of fiber-reinforced composite materials proposed by Curtin and Zhou. From the calculation results of this model, we find that the occurrence of the hysteresis loop in the cyclic loading curve is determined by the reverse yielding of the elastic-plastic materials in the strand. Both the initial thermal residual stress in the strand and the pitch length of the filaments have significant impacts on the axial and hysteretic behaviors of the strand. The damage of the filaments also affects the axial mechanical behavior of the strand remarkably at large axial strain. The critical current of the strand is calculated by the scaling law with the results of the Multi-filament twist model. The predicted results of the Multi-filament twist model show an acceptable agreement with the experiment.

Conductor analysis of the ITER FEAT poloidal field coils during a plasma scenario

NASA Astrophysics Data System (ADS)

Nicollet, S.; Hertout, P.; Duchateau, J. L.; Bleyer, A.; Bessette, D.

2002-05-01

In the framework of the ITER (International Thermonuclear Experimental Reactor) FEAT (Fusion Energy Advanced Tokamak) project, a fully superconducting PF (Poloidal Field) system has been designed in detail. The Central Solenoid and the 6 equilibrium coils constituting the PF system provide the magnetic fields which develop, shape and control the 15 MA plasma during the 1800 s of a typical plasma scenario. The 6 PF coils will be wound two-in-hand from a 45 kA niobium-titanium CICC (Cable-In-Conduit-Conductor). These coils will experience severe heat loads specially during the 400 s of the plasma burn: nuclear heating due to the 400 MW of fusion power, thermal radiation and AC losses (30 to 300 kJ). The AC losses along the PF coil pancakes are deduced from accurate magnetic field computations performed with a 3D magnetostatic code, TRAPS. The nuclear heating and the thermal radiation are assumed to be uniform over a given face of the PF coils. These heat loads are used as input to perform the thermal and hydraulic analysis with a finite element code, GANDALF. The temperature increases (0.1 to 0.4 K) are computed, the margins and performances of the conductor are evaluated.

Taonella mepensis gen. nov., sp. nov., a member of the family Rhodospirillaceae isolated from activated sludge.

PubMed

Xi, Xue-dong; Dong, Wei-liang; Zhang, Jun; Huang, Yan; Cui, Zhong-li

2013-07-01

A novel Gram-negative, non-spore-forming, rod-shaped strain, H1(T), was isolated from activated sludge by micromanipulation. No close relatives among cultured bacterial isolates were found; phylogenetic analysis based on 16S rRNA gene sequences revealed that strain H1(T) forms a deep single branch in the family Rhodospirillaceae. Cells of strain H1(T) were slightly curved to straight rods (1.2-1.4 × 1.5-1.7 µm) and motile by a single polar flagellum. Strain H1(T) was able to grow in the presence of 0-4 % NaCl and grew optimally at 37 °C and pH 6.0-7.0. Chemotaxonomic analysis revealed that strain H1(T) possessed Q-10 as the predominant ubiquinone and C18 : 1ω7c, C16 : 0 and C19 : 0 cyclo ω8c as the major fatty acids. The DNA G+C content of strain H1(T) was 65.1 mol%. Comparative analysis of 16S rRNA gene sequences, and phenotypic and chemotaxonomic data, indicate that strain H1(T) should represent a novel genus and species of the family Rhodospirillaceae. The name Taonella mepensis gen. nov., sp. nov. is proposed. The type strain of Taonella mepensis is H1(T) ( = CICC 10529(T) = CCTCC AB 2012861(T) = KACC 16940(T)).

Optimization of a protective medium for freeze-dried Pichia membranifaciens and application of this biocontrol agent on citrus fruit.

PubMed

Niu, X; Deng, L; Zhou, Y; Wang, W; Yao, S; Zeng, K

2016-07-01

To optimize a protective medium for freeze-dried Pichia membranifaciens and to evaluate biocontrol efficacies of agents against blue and green mould and anthracnose in citrus fruit. Based on the screening assays of saccharides and antioxidants, response surface methodology was used to optimize sucrose, sodium glutamate and skim milk to improve viability of freeze-dried Pi. membranifaciens. Biocontrol assays were conducted between fresh and freeze-dried Pi. membranifaciens against Penicillium italicum, Penicillium digitatum and Colletotrichum gloeosporioides in citrus fruit. Solving the regression equation indicated that the optimal protective medium was 6·06% (w/v) sucrose combined with 3·40% (w/v) sodium glutamate and 5·43% (w/v) skim milk. Pi. membranifaciens freeze-dried in the optimal protective medium showed 76·80% viability, and retained biocontrol efficacy against Pe. italicum, Pe. digitatum and Co. gloeosporioides in citrus fruit. The optimal protective medium showed more effective protective properties than each of the three protectants used alone. The viability of freeze-dried Pi. membranifaciens finally reached 76·80%. Meanwhile, the biocontrol efficacies showed no significant difference between fresh and freeze-dried yeast against Pe. italicum, Pe. digitatum and Co. gloeosporioides in citrus fruit. The results showed the potential value of Pi. membranifaciens CICC 32259 for commercialization. © 2016 The Society for Applied Microbiology.

Enhancement of  l-phenylalanine production in Escherichia coli by heterologous expression of Vitreoscilla hemoglobin.

PubMed

Wu, Wei-Bin; Guo, Xiao-Lei; Zhang, Ming-Liang; Huang, Qing-Gen; Qi, Feng; Huang, Jian-Zhong

2018-05-01

l-Phenylalanine is an important amino acid that is widely used in the production of food flavors and pharmaceuticals. Generally, l-phenylalanine production by engineered Escherichia coli requires a high rate of oxygen supply. However, the coexpression of Vitreoscilla hemoglobin gene (vgb), driven bya tac promoter, with the genes encoding 3-deoxy-d-arabinoheptulosonate-7-phosphate synthetase (aroF) and feedback-resistant chorismate mutase/prephenate dehydratase (pheA fbr ), led to increased productivity and decreased demand for aeration by E. coli CICC10245. Shake-flask studies showed that vgb-expressing strains displayed higher rates of oxygen uptake, and l-phenylalanine production under standard aeration conditions was increased. In the aerobic fermentation process, cell growth, l-phenylalanine production, and glucose consumption by the recombinant E. coli strain PAPV, which harbored aroF, pheA fbr , and tac-vgb genes, were increased compared to that in the strain harboring only aroF and pheA fbr (E. coli strain PAP), especially under oxygen-limited conditions. The vgb-expressing strain PAPV produced 21.9% more biomass and 16.6% more l-phenylalanine, while consuming only approximately 5% more glucose after 48 H of fermentation. This study demonstrates a method to enhance the l-phenylalanine production by E. coli using less intensive and thus more economical aeration conditions. © 2017 International Union of Biochemistry and Molecular Biology, Inc.

Vinegar production from post-distillation slurry deriving from rice shochu production with the addition of caproic acid-producing bacteria consortium and lactic acid bacterium.

PubMed

Yuan, Hua-Wei; Tan, Li; Chen, Hao; Sun, Zhao-Yong; Tang, Yue-Qin; Kida, Kenji

2017-12-01

To establish a zero emission process, the post-distillation slurry of a new type of rice shochu (NTRS) was used for the production of health promoting vinegar. Since the NTRS post-distillation slurry contained caproic acid and lactic acid, the effect of these two organic acids on acetic acid fermentation was first evaluated. Based on these results, Acetobacter aceti CICC 21684 was selected as a suitable strain for subsequent production of vinegar. At the laboratory scale, acetic acid fermentation of the NTRS post-distillation slurry in batch mode resulted in an acetic acid concentration of 41.9 g/L, with an initial ethanol concentration of 40 g/L, and the acetic acid concentration was improved to 44.5 g/L in fed-batch mode. Compared to the NTRS post-distillation slurry, the vinegar product had higher concentrations of free amino acids and inhibition of angiotensin I converting enzyme activity. By controlling the volumetric oxygen transfer coefficient to be similar to that of the laboratory scale production, 45 g/L of acetic acid was obtained at the pilot scale, using a 75-L fermentor with a working volume of 40 L, indicating that vinegar production can be successfully scaled up. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Novosphingobium clariflavum sp. nov., isolated from a household product plant.

PubMed

Zhang, Xin; Liu, Yang; Lin, Yafang; Wang, Lijiang; Yao, Su; Cao, Yanhua; Zhai, Lei; Tang, Xiaoli; Zhang, Lu; Zhang, Tianci; Ge, Yuanyuan; Ling, Kong; Liu, Jiquan; Cheng, Chi

2017-09-01

A Gram-stain-negative, rod-shaped, bright-yellow-pigmented bacterium, designated 164T, was isolated from a used sponge for equipment cleaning at a household product plant in China. The 16S rRNA gene sequence comparisons indicated that strain 164T was most closely related to Novosphingobium panipatense DSM 22890T (98.28 % similarity) and shared sequence similarities of 97.73-98.27 % with other members of the genus Novosphingobium. In DNA-DNA hybridization studies the relatedness between strain 164T and its closest phylogenetic neighbours was <70 %, which indicated that strain 164T represented a novel species of the genus Novosphingobium. The DNA G+C content of strain 164T was 65.9 mol%. The major respiratory quinone was ubiquinone Q-10 (83.5 %) with minor amounts of Q-9 (16.5 %). The polar lipid profile included diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine, phosphatidyldimethylethanolamine, sphingoglycolipid, phosphatidylcholine, unidentified aminolipids and unidentified aminophospholipids. Spermidine was the major polyamine. The major fatty acids were summed feature 8 (consisting of C18 : 1ω7c and/or C18 : 1ω6c) and C14 : 0 2-OH. The results obtained from phylogenetic analysis, DNA-DNA hybridization, and chemotaxonomic and phenotypic analysis support the conclusion that strain 164T represents a novel species of the genus Novosphingobium, for which the name Novosphingobium clariflavum sp. nov. is proposed. The type strain is 164T (=CICC 11035sT=DSM 103351T).

Sphingomonas morindae sp. nov., isolated from Noni (Morinda citrifolia L.) branch.

PubMed

Liu, Yang; Yao, Su; Lee, Yong-Jae; Cao, Yanhua; Zhai, Lei; Zhang, Xin; Su, Jiaojiao; Ge, Yuanyuan; Kim, Song-Gun; Cheng, Chi

2015-09-01

Two yellow bacterial strains, designated NBD5(T) and NBD8, isolated from Noni (Morinda citrifolia L.) branch were investigated using a polyphasic taxonomic approach. Cells were Gram-stain-negative, aerobic, non-spore-forming, non-motile and short rod-shaped. Phylogenetic analysis based on 16S rRNA gene sequences suggested that the strains were members of a novel species of the genus Sphingomonas, the seven closest neighbours being Sphingomonas oligoaromativorans SY-6(T) (96.9% similarity), Sphingomonas polyaromaticivorans B2-7(T) (95.8%), Sphingomonas yantingensis 1007(T) (94.9%), Sphingomonas sanguinis IFO 13937(T) (94.7%), Sphingomonas ginsenosidimutans Gsoil 1429(T) (94.6%), Sphingomonas wittichii RW1(T) (94.6%) and Sphingomonas formosensis CC-Nfb-2(T) (94.5%). Strains NBD5T and NBD8 had sphingoglycolipid, phosphatidylethanolamine, diphosphatidylglycerol, phosphatidylglycerol and phosphatidylcholine as the major polar lipids, ubiquinone 10 as the predominant respiratory quinone, and sym-homospermidine as the major polyamine. Strains NBD5(T) and NBD8 were clearly distinguished from reference type strains based on phylogenetic analysis, DNA-DNA hybridization, fatty acid composition data analysis, and comparison of a range of physiological and biochemical characteristics. It is evident from the genotypic and phenotypic data that strains NBD5(T) and NBD8 represent a novel species of the genus Sphingomonas, for which the name Sphingomonas morindae sp. nov. is proposed. The type strain is NBD5(T) ( = DSM 29151(T) = KCTC 42183(T) = CICC 10879(T)).

Draconibacterium orientale gen. nov., sp. nov., isolated from two distinct marine environments, and proposal of Draconibacteriaceae fam. nov.

PubMed

Du, Zong-Jun; Wang, Ying; Dunlap, Christopher; Rooney, Alejandro P; Chen, Guan-Jun

2014-05-01

The taxonomic characteristics of two bacterial strains, FH5T and SS4, isolated from enrichment cultures obtained from two distinct marine environments, were determined. These bacteria were Gram-stain-negative, facultatively anaerobic rods. Growth occurred at 20-40 °C (optimum, 28-32 °C), pH 5.5-9.0 (optimum, pH 7.0-7.5) and in the presence of 1-7% NaCl (optimum, 2-4%). The major cellular fatty acids were anteiso-C15:0 and iso-C15:0. Menaquinone 7 (MK-7) was the sole respiratory quinone. The major polar lipids were phosphatidylethanolamine, an unkown phospholipid and an unknown lipid. The DNA G+C contents of strains FH5T and SS4 were both determined to be 42.0 mol%. The results of DNA-DNA hybridization studies indicated that the FH5T and SS4 genomes share greater than 95% relatedness. The strains formed a distinct phyletic line within the class Bacteroidia, with less than 89.4% sequence similarity to their closest relatives with validly published names. On the basis of physiological and biochemical characteristics, 16S rRNA gene sequences and chemical properties, a novel genus and species, Draconibacterium orientale gen. nov., sp. nov., within the class Bacteroidia, are proposed, with strain FH5T (=DSM 25947T=CICC 10585T) as the type strain. In addition, a new family, Draconibacteriaceae fam. nov., is proposed to accommodate Draconibacterium gen. nov.

Biocontrol activity and patulin-removal effects of Bacillus subtilis, Rhodobacter sphaeroides and Agrobacterium tumefaciens against Penicillium expansum.

PubMed

Wang, Y; Yuan, Y; Liu, B; Zhang, Z; Yue, T

2016-11-01

This study was conducted to evaluate the biocontrol potential of Bacillus subtilis CICC 10034, Rhodobacter sphaeroides CGMCC 1.2182 and Agrobacterium tumefaciens CGMCC 1.2554 against patulin (PAT)-producer Penicillium expansum and their ability to remove PAT. Bacillus subtilis effectively inhibited P. expansum both on apples and in in vitro experiments, which reduced the rot diameter on apples by 38% compared with the control. The reduction was followed by those induced by A. tumefaciens (27·63%) and R. sphaeroides (23·67%). None of the cell-free supernatant (CFS) was able to prevent pathogen growth. Three antagonists could suppress PAT production by P. expansum on apples by 98·5, 93·7 and 94·99% after treatment with B. subtilis, R. sphaeroides and A. tumefaciens respectively. In addition, the three strains led to a 0·56-1·47 log CFU g -1 reduction in colony number of P. expansum on apples. Survival of antagonists on apple wounds revealed their tolerance to PAT. Furthermore, both live and autoclaved cells of three strains efficiently adsorbed artificially spiked PAT from medium. The selected antagonists could be applied before harvesting to control apple infection by PAT-producing fungi and also during processing to act as PAT detoxifiers. Since little information related to the capability of R. sphaeroides and A. tumefaciens to inhibit P. expansum is currently available, the results of this study provide some new perspectives to the biocontrol field. © 2016 The Society for Applied Microbiology.

Brachybacterium hainanense sp. nov., isolated from noni (Morinda citrifolia L.) branch.

PubMed

Liu, Yang; Zhai, Lei; Yao, Su; Cao, Yanhua; Cao, Yu; Zhang, Xin; Su, Jiaojiao; Ge, Yuanyuan; Zhao, Ran; Cheng, Chi

2015-11-01

A Gram-stain-positive bacterial strain, designated as NR2T, isolated from noni (Morinda citrifolia L.) branch was investigated using a polyphasic taxonomic approach. The cells were small coccoid to ovoid, non-spore-forming and motile. Phylogenetic analysis based on 16S rRNA gene sequences showed that the strain was a representative of a member of the genus Brachybacterium, to which the most closely related neighbours were Brachybacterium squillarum M-6-3T (97.90 % similarity), Brachybacterium faecium DSM 4810T (97.50 %), Brachybacterium sacelli LMG 20345T (97.41 %), Brachybacterium phenoliresistens phenol-AT (97.36 %), Brachybacterium nesterenkovii DSM 9573T (97.36 %) and Brachybacterium rhamnosum LMG 19848T (97.32 %). The polar lipid profile of strain NR2T consisted of diphosphatidylglycerol, phosphatidylglycerol, unknown phospholipids and unknown glycolipids. The predominant respiratory quinone was MK-8, with MK-9 and MK-7 as minor components. The major fatty acids were anteiso-C15 : 0 and iso-C15 : 0. Strain NR2T was clearly distinguishable from the type strains of related species on the basis of phylogenetic analysis, DNA-DNA hybridization, fatty acid composition data analysis and a range of physiological and comparison of biochemical characteristics. It is evident from the genotypic and phenotypic data that strain NR2T represents a novel species of the genus Brachybacterium, for which the name Brachybacterium hainanense sp. nov. is proposed. The type strain is NR2T ( = DSM 29535T = CICC 10874T).

Halomonas alkalicola sp. nov., isolated from a household product plant.

PubMed

Tang, Xiaoli; Zhai, Lei; Lin, Yafang; Yao, Su; Wang, Lijiang; Ge, Yuanyuan; Liu, Yang; Zhang, Xin; Zhang, Tianci; Zhang, Lu; Liu, Jiquan; Cheng, Chi

2017-05-01

A Gram-stain-negative, alkaliphilic and moderately halophilic bacterium, designated 56-L4-10aEnT, was isolated from a household product plant in China. Cells of the novel isolate were rod-shaped, non-spore-forming and non-motile. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain 56-L4-10aEnT belongs to the genus Halomonas, with the six closest neighbours being Halomonas mongoliensis Z-7009T (97.59 % 16S rRNA gene sequence similarity), Halomonas ventosae Al12T (97.35 %), Halomonas campaniensis 5AGT (97.22 %), Halomonas alimentaria YKJ-16T (97.22 %), Halomonas shengliensis SL014B-85T (97.12 %) and Halomonas fontilapidosi 5CRT (97.09 %). The main polar lipids of strain 56-L4-10aEnT contained diphosphatidylglycerol, phosphatidylglycerol and phosphatidylethanolamine. The predominant respiratory quinone was Q-9, with Q-8 as a minor component. The major fatty acids were C18 : 1ω7c/C18 : 1ω6c and C16 : 0. Strain 56-L4-10aEnT was clearly distinguished from the type strains mentioned above through phylogenetic analysis, DNA-DNA hybridization, fatty acid composition data and a range of physiological and biochemical characteristics comparisons. It is evident from the genotypic and phenotypic data that strain 56-L4-10aEnTcould be classified as a representative of a novel species of the genus Halomonas, for which the name Halomonas alkalicola sp. nov. is proposed. The type strain is 56-L4-10aEnT (=CICC 11012sT=DSM 103354T).

Aquimarina agarivorans sp. nov., a genome-sequenced member of the class Flavobacteriia isolated from Gelidium amansii.

PubMed

Zhou, Yan-Xia; Wang, Chao; Du, Zong-Jun; Chen, Guan-Jun

2015-08-01

A novel Gram-stain-negative, facultatively anaerobic, rod-shaped, agar-digesting bacterial strain, designated HQM9T, was isolated from the surface of the marine red alga Gelidium amansii collected from the intertidal zone of Weihai, China. Cells of HQM9T were 3.0-4.0 μm long and 0.2-0.3 μm wide and lacked flagella. The new isolate grew optimally at 28-30 °C, at pH 7.0-7.5, and in the presence of 2.5-3.0% NaCl. The predominant cellular fatty acids were iso-C15 : 0 and iso-C17 : 0 3-OH. The sole menaquinone was MK-6. The DNA G+C content was 33 mol%. The major polar lipids were comprised of phosphatidylethanolamine and four unknown polar lipids. Based on the 16S rRNA gene sequence, the closest relative was Aquimarina agarilytica ZC1T with 97.16% sequence similarity, with which strain HQM9T formed a distinct cluster belonging to the genus Aquimarina in a phylogenetic tree. Moreover, average nucleotide identity and estimated DNA-DNA hybridization values between strains HQM9T and ZC1T were 78.7% and 12.50 ± 2.95%, respectively. On the basis of phenotypic, chemotaxonomic and phylogenetic analysis, strain HQM9T represents the type strain of a novel species within the genus Aquimarina in the family Flavobacteriaceae, phylum Bacteroidetes, for which the name Aquimarina agarivorans sp. nov. is proposed. The type strain is HQM9T ( = ATCC BAA-2612T = CICC 10835T).

Marinagarivorans algicola gen. nov., sp. nov., isolated from marine algae.

PubMed

Guo, Ling-Yun; Li, Dong-Qi; Sang, Jin; Chen, Guan-Jun; Du, Zong-Jun

2016-03-01

Two novel agar-degrading, Gram-stain-negative, motile, heterotrophic, facultatively anaerobic and pale yellow-pigmented bacterial strains, designated Z1 T and JL1, were isolated from marine algae Gelidium amansii (Lamouroux) and Gracilaria verrucosa , respectively. Growth of the isolates was optimal at 28-30 °C, pH 7.0-7.5 and with 2-3 % (w/v) NaCl. Both strains contained Q-8 as the sole respiratory quinone. The major cellular fatty acids in strain Z1 T were C 18 : 1 ω7 c , C 16 : 0 and summed feature 3 (C 16 : 1 ω7 c and/or iso-C 15 : 0 2-OH). The predominant polar lipids in strain Z1 T were phosphatidylethanolamine, phosphatidylglycerol and an aminolipid. The genomic DNA G+C content of both strains was 45.1 mol%. Strains Z1 T and JL1 were closely related, with 99.9 % 16S rRNA gene sequence similarity. The average nucleotide identity (ANI) value between strains Z1 T and JL1 was 99.3 %. Phylogenetic analysis based on 16S rRNA gene sequences revealed that strains Z1 T and JL1 form a distinct phyletic line within the class Gammaproteobacteria , with less than 92.3 % similarity to their closest relatives. Based on data from the current polyphasic study, the isolates are proposed to belong to a novel species of a new genus designated Marinagarivorans algicola gen. nov., sp. nov. The type strain of the type species is Z1 T ( = ATCC BAA-2617 T  = CICC 10859 T ).

High field solenoids for muon cooling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Green, M.A.; Eyssa, Y.; Kenny, S.

1999-09-08

The proposed cooling system for the muon collider will consist of a 200 meter long line of alternating field straight solenoids interspersed with bent solenoids. The muons are cooled in all directions using a 400 mm long section liquid hydrogen at high field. The muons are accelerated in the forward direction by about 900 mm long, 805 MHz RF cavities in a gradient field that goes from 6 T to -6 T in about 300 mm. The high field section in the channel starts out at an induction of about 2 T in the hydrogen. As the muons proceed downmore » the cooling channel, the induction in the liquid hydrogen section increases to inductions as high as 30 T. The diameter of the liquid hydrogen section starts at 750 mm when the induction is 2 T. As the induction in the cooling section goes up, the diameter of the liquid hydrogen section decreases. When the high field induction is 30 T, the diameter of the liquid hydrogen section is about 80 mm. When the high field solenoid induction is below 8.5 T or 9T, niobium titanium coils are proposed for generating .the magnetic field. Above 8.5 T or 9 T to about 20 T, graded niobium tin and niobium titanium coils would be used at temperatures down to 1.8 K. Above 20 T, a graded bybrid magnet system is proposed, where the high field magnet section (above 20 T) is either a conventional water cooled coil section or a water cooled Bitter type coil. Two types of superconducting coils have been studied. They include; epoxy impregnated intrinsically stable coils, and cable in conduit conductor (CICC) coils with helium in the conduit.« less

Burkholderia metalliresistens sp. nov., a multiple metal-resistant and phosphate-solubilising species isolated from heavy metal-polluted soil in Southeast China.

PubMed

Guo, Jun Kang; Ding, Yong Zhen; Feng, Ren Wei; Wang, Rui Gang; Xu, Ying Ming; Chen, Chun; Wei, Xiu Li; Chen, Wei Min

2015-06-01

A metal-resistant and phosphate-solubilising bacterium, designated as strain D414(T), was isolated from heavy metal (Pb, Cd, Cu and Zn)-polluted paddy soils at the surrounding area of Dabao Mountain Mine in Southeast China. The minimum inhibitory concentrations of heavy metals for strain D414(T) were 2000 mg L(-1) (Cd), 800 mg L(-1) (Pb), 150 mg L(-1) (Cu) and 2500 mg L(-1) (Zn). The strain possessed plant growth-promoting properties, such as 1-aminocyclopropane-1-carboxylate assimilation, indole production and phosphate solubilisation. Analysis of 16S rRNA gene sequence indicated that the isolate is a member of the genus Burkholderia where strain D414(T) formed a distinct phyletic line with validly described Burkholderia species. Strain D414(T) is closely related to Burkholderia tropica DSM 15359(T), B. bannensis NBRC E25(T) and B. unamae DSM 17197(T), with 98.5, 98.3 and 98.3 % sequence similarities, respectively. Furthermore, less than 34 % DNA-DNA relatedness was detected between strain D414(T) and the type strains of the phylogenetically closest species of Burkholderia. The dominant fatty acids of strain D414(T) were C14:0, C16:0, C17:0 cyclo and C18:1 ω7c. The DNA G+C content was 62.3 ± 0.5 mol%. On the basis of genotypic, phenotypic and phylogenetic data, strain D414(T) represents a novel species, for which the name Burkholderia metalliresistens sp. nov. is proposed, with D414(T) (=CICC 10561(T) = DSM 26823(T)) as the type strain.

Factors Influencing Intracavitary Electrocardiographic P-Wave Changes during Central Venous Catheter Placement

PubMed Central

Wang, Guorong; Guo, Ling; Jiang, Bin; Huang, Min; Zhang, Jian; Qin, Ying

2015-01-01

Amplitude changes in the P-wave of intracavitary electrocardiography have been used to assess the tip placement of central venous catheters. The research assessed the sensitivity and specificity of this sign in comparison with standard radiographic techniques for tip location, focusing on factors influencing its clinical utility. Both intracavitary electrocardiography guided tip location and X-ray positioning were used to verify catheter tip locations in patients undergoing central venous catheter insertion. Intracavitary electrocardiograms from 1119 patients (of a total 1160 subjects) showed specific amplitude changes in the P-wave. As the results show, compared with X-ray positioning, the sensitivity of electrocardiography-guided tip location was 97.3%, with false negative rate of 2.7%; the specificity was 1, with false positive rate of zero. Univariate analyses indicated that features including age, gender, height, body weight, and heart rate have no statistically significant influence on P-wave amplitude changes (P>0.05). Multivariate logistic regression revealed that catheter insertion routes (OR = 2.280, P = 0.003) and basal P-wave amplitude (OR = 0.553, P = 0.003) have statistically significant impacts on P-wave amplitude changes. As a reliable indicator of tip location, amplitude change in the P-wave has proved of good sensitivity and excellent specificity, and the minor, zero, false positive rate supports the clinical utility of this technique in early recognition of malpositioned tips. A better sensitivity was achieved in placement of centrally inserted central catheters (CICCs) than that of peripherally inserted central catheters (PICCs). In clinical practice, a combination of intracavitary electrocardiography, ultrasonic inspection and the anthropometric measurement method would further improve the accuracy. PMID:25915758

Streptomyces euryhalinus sp. nov., a new actinomycete isolated from a mangrove forest.

PubMed

Biswas, Kaushik; Choudhury, Jayanta D; Mahansaria, Riddhi; Saha, Malay; Mukherjee, Joydeep

2017-06-01

A Gram-positive, aerobic, non-motile actinomycete (strain MS 3/20 T ) was isolated from the sediment of the Sundarbans mangrove forest in India. On International Streptomyces Project (ISP) medium 2, the isolate produced yellowish brown to red aerial hyphae that carried spiny-surfaced spores in a retinaculum-apertum arrangement. Whole-cell hydrolysate of the strain contained LL-diaminopimelic acid and galactose. Predominant menaquinones were MK-9(H 8 ) and MK-9(H 6 ). Diagnostic polar lipids were glycolipid, phosphatidylglycerol, phosphatidylethanolamine, phosphatidylcholine, unidentified phospholipid and unidentified amino lipid. The major fatty acids were anteiso-C 15:0 (17.53%), iso-C 16:0 (23.89%) and anteiso-C 17:0 (10.29%). The strain showed 100% 16S ribosomal RNA (rRNA) gene sequence similarity with Streptomyces variabilis NBRC 12825 T , Streptomyces erythrogriseus LMG 19406 T , Streptomyces griseoincarnatus LMG 19316 T and Streptomyces labedae NBRC 15864 T . However, strain MS 3/20 T could be distinguished from these and seven other closely related species based on low levels of DNA-DNA relatedness (27.2-53.8%), supported by the unique banding pattern obtained from random amplified polymorphic DNA-PCR amplification and the distinctive matrix-assisted laser desorption/ionization-time-of-flight/mass spectrometry (MALDI-TOF/MS) profile of whole-cell proteins acquired for strain MS 3/20 T in comparison with its phylogenetic relatives. Disparate morphological, physiological and chemotaxonomic features, principally growth in NaCl, further corroborated the distinction of strain MS 3/20 T from other phylogenetic relatives. Strain MS 3/20 T is therefore suggested to be a novel species of the genus Streptomyces, for which the name Streptomyces euryhalinus sp. nov. is proposed. The type strain is MS 3/20 T (=CICC 11032 T =DSM 103378 T ).

49 CFR 178.985 - Vibration test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Vibration test. 178.985 Section 178.985... Testing of Large Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A...

49 CFR 178.985 - Vibration test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Vibration test. 178.985 Section 178.985... Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A sample Large...

49 CFR 178.985 - Vibration test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Vibration test. 178.985 Section 178.985... Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A sample Large...

49 CFR 178.985 - Vibration test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Vibration test. 178.985 Section 178.985... Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A sample Large...

49 CFR 178.985 - Vibration test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Vibration test. 178.985 Section 178.985... Packagings § 178.985 Vibration test. (a) General. All rigid Large Packaging and flexible Large Packaging design types must be capable of withstanding the vibration test. (b) Test method. (1) A sample Large...

Development of a high-frequency and large-stroke fatigue testing system for rubber

NASA Astrophysics Data System (ADS)

Chen, Gang; Wu, Hao; Gao, Jianwen; Lin, Qiang

2017-04-01

The limited capabilities of current fatigue testing machines have resulted in studies on the fatigue behavior of rubber under large-displacement amplitude and high frequency being very sparse. In this study, a fatigue testing system that can carry out large-displacement amplitude and high-frequency fatigue tests on rubber was developed using a moving magnet voice coil motor (MMVCM) actuator, with finite element analysis applied to analyze the thrust of the MMVCM actuator. The results of a series of cyclic tension tests conducted on vulcanized natural rubber specimens using the developed fatigue testing system verify that it has high precision, low noise, large-stroke, and high-frequency characteristics. Further, the load frame with the developed MMVCM actuator is feasible for material testing, especially for large-stroke and high-frequency fatigue tests.

Structural modeling of HTS tapes and cables

NASA Astrophysics Data System (ADS)

Allen, N. C.; Chiesa, L.; Takayasu, M.

2016-12-01

Structural finite element analysis (FEA) has been used as an insightful tool to investigate the electromechanical behavior of HTS REBCO tapes and twisted stacked-tape cables under tension, torsion, bending and combined loads. A novel technique was developed for modeling the layered composite structure of the 2G tapes with structural solid-shell elements in ANSYS®. The FEA models produced detailed strain information for the REBCO superconducting layer which was then paired with an analytical model to predict the critical current performance of the 2G HTS tapes under various loads. Two commercially available HTS tapes (SuperPower and SuNAM) under tension, torsion and combined tension-torsion were first analyzed with FEA and compared with available experimental results at 77 K. A sharp critical current degradation was experienced at the yield strength of the tapes under tension and below a 100 mm twist-pitch under torsion. Combined tension-torsion loads had a more gradual degradation of critical current for twist-pitches of 115 mm or shorter but had a negligible difference compared to pure tension for longer twist-pitches. Using the structural solid-shell technique for modeling 2G tapes in ANSYS®, an FEA methodology for simulating full scale three-dimensional HTS stacked-tape cables under pure bending was created. A model of a Twisted-Stacked Tape Cable (TSTC), a configuration first proposed at MIT, was initially developed and then adapted to the slotted-core HTS Cable-In-Conduit Conductor produced by the ENEA laboratory in Italy. The numerical axial strain of the HTS REBCO tapes within the cables as calculated by FEA were found to agree with an analytical model for two cases: perfect-slip (frictionless) and no-slip (bonded). The ENEA CICC model was also compared with recent experimental critical current data at 77 K and was found to match best using a low friction coefficient of 0.02 indicating that the tapes within the cable freely slide with respect to each other helping to reduce the axial strain during bending.

Bacillus ciccensis sp. nov., isolated from maize (Zea mays L.) seeds.

PubMed

Liu, Yang; Li, Nannan; Eom, Mi Kyung; Schumann, Peter; Zhang, Xin; Cao, Yanhua; Ge, Yuanyuan; Xiao, Ming; Zhao, Jiuran; Cheng, Chi; Kim, Song-Gun

2017-11-01

Two Gram-stain-positive bacterial strains, designated as 5L6 T and 6L6, isolated from seeds of hybrid maize (Zea mays L., Jingke 968) were investigated using a polyphasic taxonomic approach. The cells were aerobic, motile, endospore-forming and rod-shaped. Phylogenetic analysis based on 16S rRNA gene sequences showed that the isolates were recognized as a species of the genus Bacillus, to which the five closest neighbours are Bacillus solani FJAT-18043 T (99.8 % similarity), Bacillus horneckiae DSM 23495 T (97.7 %), Bacillus eiseniae A1-2 T (97.4 %), Bacillus kochii WCC 4582 T (97.1 %) and Bacillus purgationiresistens DS22 T (97.0 %). The DNA G+C content of strain 5L6 T was 37.4 mol%. Its polar lipid profile consisted of diphosphatidylglycerol, phosphatidylglycerol and phosphatidylethanolamine. The predominant respiratory quinone was MK-7 and the major fatty acids were iso-C15 : 0, anteiso-C15 : 0, iso-C16 : 0, iso-C14 : 0, anteiso-C17 : 0 and C16 : 1 ω7c alcohol. The cell-wall peptidoglycan contained ornithine, serine, aspartic acid, glutamic acid and alanine while diaminopimelic acid could not be detected. Strains 5L6 T and 6L6 were clearly distinguished from the type strains of related validly named species using phylogenetic analysis, DNA-DNA hybridization, fatty acid analysis, peptidoglycan analysis and comparison of a range of physiological and biochemical characteristics. The genotypic and phenotypic data show that strains 5L6 T and 6L6 represent a novel species of the genus Bacillus, for which the name Bacillusciccensis sp. nov. is proposed. The type strain is 5L6 T (=KCTC 33663 T =CICC 23855 T =DSM 104513 T ).

The intracavitary ECG method for positioning the tip of central venous access devices in pediatric patients: results of an Italian multicenter study.

PubMed

Rossetti, Francesca; Pittiruti, Mauro; Lamperti, Massimo; Graziano, Ugo; Celentano, Davide; Capozzoli, Giuseppe

2015-01-01

The Italian Group for Venous Access Devices (GAVeCeLT) has carried out a multicenter study investigating the safety and accuracy of intracavitary electrocardiography (IC-ECG) in pediatric patients. We enrolled 309 patients (age 1 month-18 years) candidate to different central venous access devices (VAD) - 56 peripherally inserted central catheters (PICC), 178 short term centrally inserted central catheters (CICC), 65 long term VADs, 10 VADs for dialysis - in five Italian Hospitals. Three age groups were considered: A (<4 years, n = 157), B (4-11 years, n = 119), and C (12-18 years, n = 31). IC-ECG was applicable in 307 cases. The increase of the P wave on IC-ECG was detected in all cases but two. The tip of the catheter was positioned at the cavo-atrial junction (CAJ) (i.e., at the maximal height of the P wave on IC-ECG) and the position was checked during the procedure by fluoroscopy or chest x-ray, considering the CAJ at 1-2 cm (group A), 1.5-3 cm (group B), or 2-4 cm (group C) below the carina. There were no complications related to IC-ECG. The overall match between IC-ECG and x-ray was 95.8% (96.2% in group A, 95% in group B, and 96.8% in group C). In 95 cases, the IC-ECG was performed with a dedicated ECG monitor, specifically designed for IC-ECG (Nautilus, Romedex): in this group, the match between IC-ECG and x-ray was 98.8%. We conclude that the IC-ECG method is safe and accurate in the pediatric patients. The applicability of the method is 99.4% and its feasibility is 99.4%. The accuracy is 95.8% and even higher (98.8%) when using a dedicated ECG monitor.

A New Facility for Testing Superconducting Solenoid Magnets with Large Fringe Fields at Fermilab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orris, D.; Carcagno, R.; Nogiec, J.

2013-09-01

Testing superconducting solenoid with no iron flux return can be problematic for a magnet test facility due to the large magnetic fringe fields generated. These large external fields can interfere with the operation of equipment while precautions must be taken for personnel supporting the test. The magnetic forces between the solenoid under test and the external infrastructure must also be taken under consideration. A new test facility has been designed and built at Fermilab specifically for testing superconducting magnets with large external fringe fields. This paper discusses the test stand design, capabilities, and details of the instrumentation and controls withmore » data from the first solenoid tested in this facility: the Muon Ionization Cooling Experiment (MICE) coupling coil.« less

The Rights and Responsibility of Test Takers When Large-Scale Testing Is Used for Classroom Assessment

ERIC Educational Resources Information Center

van Barneveld, Christina; Brinson, Karieann

2017-01-01

The purpose of this research was to identify conflicts in the rights and responsibility of Grade 9 test takers when some parts of a large-scale test are marked by teachers and used in the calculation of students' class marks. Data from teachers' questionnaires and students' questionnaires from a 2009-10 administration of a large-scale test of…

Load reduction test method of similarity theory and BP neural networks of large cranes

NASA Astrophysics Data System (ADS)

Yang, Ruigang; Duan, Zhibin; Lu, Yi; Wang, Lei; Xu, Gening

2016-01-01

Static load tests are an important means of supervising and detecting a crane's lift capacity. Due to space restrictions, however, there are difficulties and potential danger when testing large bridge cranes. To solve the loading problems of large-tonnage cranes during testing, an equivalency test is proposed based on the similarity theory and BP neural networks. The maximum stress and displacement of a large bridge crane is tested in small loads, combined with the training neural network of a similar structure crane through stress and displacement data which is collected by a physics simulation progressively loaded to a static load test load within the material scope of work. The maximum stress and displacement of a crane under a static load test load can be predicted through the relationship of stress, displacement, and load. By measuring the stress and displacement of small tonnage weights, the stress and displacement of large loads can be predicted, such as the maximum load capacity, which is 1.25 times the rated capacity. Experimental study shows that the load reduction test method can reflect the lift capacity of large bridge cranes. The load shedding predictive analysis for Sanxia 1200 t bridge crane test data indicates that when the load is 1.25 times the rated lifting capacity, the predicted displacement and actual displacement error is zero. The method solves the problem that lifting capacities are difficult to obtain and testing accidents are easily possible when 1.25 times related weight loads are tested for large tonnage cranes.

Large-Scale Multiobjective Static Test Generation for Web-Based Testing with Integer Programming

ERIC Educational Resources Information Center

Nguyen, M. L.; Hui, Siu Cheung; Fong, A. C. M.

2013-01-01

Web-based testing has become a ubiquitous self-assessment method for online learning. One useful feature that is missing from today's web-based testing systems is the reliable capability to fulfill different assessment requirements of students based on a large-scale question data set. A promising approach for supporting large-scale web-based…

Test and Evaluation of Ultrasonic Additive Manufacturing (UAM) for a Large Aircraft Maintenance Shelter (LAMS) Baseplate

DTIC Science & Technology

2015-03-26

TEST AND EVALUATION OF ULTRASONIC ADDITIVE MANUFACTURING (UAM) FOR A LARGE AREA MAINTENANCE...States Government. AFIT-ENV-MS-15-M-158 TEST AND EVALUATION OF ULTRASONIC ADDITIVE MANUFACTURING FOR A LARGE AREA MAINTENANCE SHELTER...Civil Engineer (CE) operations. This research replicates a Large Area Maintenance Shelter (LAMS) baseplate design for ultrasonic additive

Voices from Test-Takers: Further Evidence for Language Assessment Validation and Use

ERIC Educational Resources Information Center

Cheng, Liying; DeLuca, Christopher

2011-01-01

Test-takers' interpretations of validity as related to test constructs and test use have been widely debated in large-scale language assessment. This study contributes further evidence to this debate by examining 59 test-takers' perspectives in writing large-scale English language tests. Participants wrote about their test-taking experiences in…

Large-Scale Wind Turbine Testing in the NASA 24.4m (80) by 36.6m(120) Wind Tunnel

NASA Technical Reports Server (NTRS)

Zell, Peter T.; Imprexia, Cliff (Technical Monitor)

2000-01-01

The 80- by 120-Foot Wind Tunnel at NASA Ames Research Center in California provides a unique capability to test large-scale wind turbines under controlled conditions. This special capability is now available for domestic and foreign entities wishing to test large-scale wind turbines. The presentation will focus on facility capabilities to perform wind turbine tests and typical research objectives for this type of testing.

Critical Issues in Large-Scale Assessment: A Resource Guide.

ERIC Educational Resources Information Center

Redfield, Doris

The purpose of this document is to provide practical guidance and support for the design, development, and implementation of large-scale assessment systems that are grounded in research and best practice. Information is included about existing large-scale testing efforts, including national testing programs, state testing programs, and…

49 CFR 178.975 - Top lift test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the test. For all Large Packagings design types designed to be lifted from the top, there may be no permanent deformation which renders the Large Packagings unsafe for transport and no loss of contents. ... load being evenly distributed. (c) Test method. (1) A Large Packaging must be lifted in the manner for...

Large-aperture space optical system testing based on the scanning Hartmann.

PubMed

Wei, Haisong; Yan, Feng; Chen, Xindong; Zhang, Hao; Cheng, Qiang; Xue, Donglin; Zeng, Xuefeng; Zhang, Xuejun

2017-03-10

Based on the Hartmann testing principle, this paper proposes a novel image quality testing technology which applies to a large-aperture space optical system. Compared with the traditional testing method through a large-aperture collimator, the scanning Hartmann testing technology has great advantages due to its simple structure, low cost, and ability to perform wavefront measurement of an optical system. The basic testing principle of the scanning Hartmann testing technology, data processing method, and simulation process are presented in this paper. Certain simulation results are also given to verify the feasibility of this technology. Furthermore, a measuring system is developed to conduct a wavefront measurement experiment for a 200 mm aperture optical system. The small deviation (6.3%) of root mean square (RMS) between experimental results and interferometric results indicates that the testing system can measure low-order aberration correctly, which means that the scanning Hartmann testing technology has the ability to test the imaging quality of a large-aperture space optical system.

Transmitted wavefront testing with large dynamic range based on computer-aided deflectometry

NASA Astrophysics Data System (ADS)

Wang, Daodang; Xu, Ping; Gong, Zhidong; Xie, Zhongmin; Liang, Rongguang; Xu, Xinke; Kong, Ming; Zhao, Jun

2018-06-01

The transmitted wavefront testing technique is demanded for the performance evaluation of transmission optics and transparent glass, in which the achievable dynamic range is a key issue. A computer-aided deflectometric testing method with fringe projection is proposed for the accurate testing of transmitted wavefronts with a large dynamic range. Ray tracing of the modeled testing system is carried out to achieve the virtual ‘null’ testing of transmitted wavefront aberrations. The ray aberration is obtained from the ray tracing result and measured slope, with which the test wavefront aberration can be reconstructed. To eliminate testing system modeling errors, a system geometry calibration based on computer-aided reverse optimization is applied to realize accurate testing. Both numerical simulation and experiments have been carried out to demonstrate the feasibility and high accuracy of the proposed testing method. The proposed testing method can achieve a large dynamic range compared with the interferometric method, providing a simple, low-cost and accurate way for the testing of transmitted wavefronts from various kinds of optics and a large amount of industrial transmission elements.

NOAO testing procedures for large optics

NASA Astrophysics Data System (ADS)

Stepp, Larry M.; Poczulp, Gary A.; Pearson, Earl T.; Roddier, Nicolas A.

1992-03-01

This paper describes optical testing procedures used at the National Optical Astronomy Observatories (NOAO) for testing large optics. It begins with a discussion of the philosophy behind the testing approach and then describes a number of different testing methods used at NOAO, including the wire test, full-aperture and sub-aperture Hartmann testing, and scatterplate interferometry. Specific innovations that enhance the testing capabilities are mentioned. NOAO data reduction software is described. Examples are given of specific output formats that are useful to the optician, using illustrations taken from recent testing of a 3.5- meter, f/1.75 borosilicate honeycomb mirror. Finally, we discuss some of the optical testing challenges posed by the large optics for the Gemini 8-meter Telescopes Project.

Heat transfer in pipes

NASA Technical Reports Server (NTRS)

Burbach, T.

1985-01-01

The heat transfer from hot water to a cold copper pipe in laminar and turbulent flow condition is determined. The mean flow through velocity in the pipe, relative test length and initial temperature in the vessel were varied extensively during tests. Measurements confirm Nusselt's theory for large test lengths in laminar range. A new equation is derived for heat transfer for large starting lengths which agrees satisfactorily with measurements for large starting lengths. Test results are compared with the new Prandtl equation for heat transfer and correlated well. Test material for 200- and to 400-diameter test length is represented at four different vessel temperatures.

Composite Overwrap Fragmentation Observations, Concerns, and Recommendations

NASA Technical Reports Server (NTRS)

Bangham, Mike; Hovater, Mary

2017-01-01

A series of test activities has raised some concerns about the generation of orbital debris caused by failures of composite overwrapped pressure vessels (COPVs). These tests have indicated that a large number of composite fragments can be produced by either pressure burst failures or by high-speed impacts. A review of prior high-speed tests with COPV indicates that other tests have produced large numbers of composite fragments. As was the case with the test referenced here, the tests tended to produce a large number of small composite fragments with relatively low velocities induced by the impact and or gas expansion.

Evaluation of genotoxicity testing of FDA approved large molecule therapeutics.

PubMed

Sawant, Satin G; Fielden, Mark R; Black, Kurt A

2014-10-01

Large molecule therapeutics (MW>1000daltons) are not expected to enter the cell and thus have reduced potential to interact directly with DNA or related physiological processes. Genotoxicity studies are therefore not relevant and typically not required for large molecule therapeutic candidates. Regulatory guidance supports this approach; however there are examples of marketed large molecule therapeutics where sponsors have conducted genotoxicity studies. A retrospective analysis was performed on genotoxicity studies of United States FDA approved large molecule therapeutics since 1998 identified through the Drugs@FDA website. This information was used to provide a data-driven rationale for genotoxicity evaluations of large molecule therapeutics. Fifty-three of the 99 therapeutics identified were tested for genotoxic potential. None of the therapeutics tested showed a positive outcome in any study except the peptide glucagon (GlucaGen®) showing equivocal in vitro results, as stated in the product labeling. Scientific rationale and data from this review indicate that testing of a majority of large molecule modalities do not add value to risk assessment and support current regulatory guidance. Similarly, the data do not support testing of peptides containing only natural amino acids. Peptides containing non-natural amino acids and small molecules in conjugated products may need to be tested. Copyright © 2014 Elsevier Inc. All rights reserved.

Definition of ground test for verification of large space structure control

NASA Technical Reports Server (NTRS)

Doane, G. B., III; Glaese, J. R.; Tollison, D. K.; Howsman, T. G.; Curtis, S. (Editor); Banks, B.

1984-01-01

Control theory and design, dynamic system modelling, and simulation of test scenarios are the main ideas discussed. The overall effort is the achievement at Marshall Space Flight Center of a successful ground test experiment of a large space structure. A simplified planar model of ground test experiment of a large space structure. A simplified planar model of ground test verification was developed. The elimination from that model of the uncontrollable rigid body modes was also examined. Also studied was the hardware/software of computation speed.

Ground test experiment for large space structures

NASA Technical Reports Server (NTRS)

Tollison, D. K.; Waites, H. B.

1985-01-01

In recent years a new body of control theory has been developed for the design of control systems for Large Space Structures (LSS). The problems of testing this theory on LSS hardware are aggravated by the expense and risk of actual in orbit tests. Ground tests on large space structures can provide a proving ground for candidate control systems, but such tests require a unique facility for their execution. The current development of such a facility at the NASA Marshall Space Flight Center (MSFC) is the subject of this report.

Potential utilization of the NASA/George C. Marshall Space Flight Center in earthquake engineering research

NASA Technical Reports Server (NTRS)

Scholl, R. E. (Editor)

1979-01-01

Earthquake engineering research capabilities of the National Aeronautics and Space Administration (NASA) facilities at George C. Marshall Space Flight Center (MSFC), Alabama, were evaluated. The results indicate that the NASA/MSFC facilities and supporting capabilities offer unique opportunities for conducting earthquake engineering research. Specific features that are particularly attractive for large scale static and dynamic testing of natural and man-made structures include the following: large physical dimensions of buildings and test bays; high loading capacity; wide range and large number of test equipment and instrumentation devices; multichannel data acquisition and processing systems; technical expertise for conducting large-scale static and dynamic testing; sophisticated techniques for systems dynamics analysis, simulation, and control; and capability for managing large-size and technologically complex programs. Potential uses of the facilities for near and long term test programs to supplement current earthquake research activities are suggested.

Large-Scale Operations Management Test of Use of The White Amur for Control of Problem Aquatic Plants. Report 1. Baseline Studies. Volume V. The Herpetofauna of Lake Conway, Florida.

DTIC Science & Technology

1981-06-01

V ADA02 7414 UNIVERSITY OF SOUTH FLORIDA TAMPA DEPT OF BIOLOGY F/6 6/6 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE MHITE AMUM-ETC(U) JUN 81...Army Engineer Waterways Expiftaton P. 0. Box 631, Vicksburg, Miss. 391( 0 81 8 1102 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR...78-22// 4. TITLE (and Su~btitle) 5 TYPE OF REPORT & PERIOD COVERED LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE. or Report I of a series THE W4HITE

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume II. The Fish, Mammals, and Waterfowl of Lake Conway, Florida.

DTIC Science & Technology

1982-02-01

7AD-AI3 853 ’FLORIDA SAME AND FRESH WATER FISH COMMISSION ORLANDO F/ 616 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR--ETC(U...of a series of reports documenting a large-scale operations management test of use of the white amur for control of problem aquatic plants in Lake...M. 1982. "Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants; Report 2, First Year Poststock- ing

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume VI. The Water and Sediment Quality of Lake Conway, Florida.

DTIC Science & Technology

1982-02-01

AD A113 .5. ORANGE COUNTY POLLUTION CONTROL DEPT ORLANDO FL F/S 6/6 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR-ETC(U) FEB 82 H D...Large-Scale Operations Management Test of use of the white amur for control of problem aquatic plants in Lake Conway, Fla. Report 1 of the series presents...as follows: Miller, D. 1982. "Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants; Report 2, First

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 4. Third Year Poststocking Results. Volume VI. The Water and Sediment Quality of Lake Conway, Florida.

DTIC Science & Technology

1983-01-01

RAI-RI247443 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE i/i UNITE AMUR FOR CONTR.. (U) MILLER RND MILLER INC ORLANDO FL H D MILLER ET RL...LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC PLANTS Report 1: Baseline Studies Volume I...Boyd, J. 1983. "Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants; Report 4, Third Year Poststocking

Role of optometry school in single day large scale school vision testing

PubMed Central

Anuradha, N; Ramani, Krishnakumar

2015-01-01

Background: School vision testing aims at identification and management of refractive errors. Large-scale school vision testing using conventional methods is time-consuming and demands a lot of chair time from the eye care professionals. A new strategy involving a school of optometry in single day large scale school vision testing is discussed. Aim: The aim was to describe a new approach of performing vision testing of school children on a large scale in a single day. Materials and Methods: A single day vision testing strategy was implemented wherein 123 members (20 teams comprising optometry students and headed by optometrists) conducted vision testing for children in 51 schools. School vision testing included basic vision screening, refraction, frame measurements, frame choice and referrals for other ocular problems. Results: A total of 12448 children were screened, among whom 420 (3.37%) were identified to have refractive errors. 28 (1.26%) children belonged to the primary, 163 to middle (9.80%), 129 (4.67%) to secondary and 100 (1.73%) to the higher secondary levels of education respectively. 265 (2.12%) children were referred for further evaluation. Conclusion: Single day large scale school vision testing can be adopted by schools of optometry to reach a higher number of children within a short span. PMID:25709271

10 CFR 431.96 - Uniform test method for the measurement of energy efficiency of small, large, and very large...

Code of Federal Regulations, 2010 CFR

2010-01-01

... DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL... measurement of energy efficiency of small, large, and very large commercial package air conditioning and... section contains test procedures for measuring, pursuant to EPCA, the energy efficiency of any small...

Electrical characterization of a Mapham inverter using pulse testing techniques

NASA Technical Reports Server (NTRS)

Baumann, E. D.; Myers, I. T.; Hammoud, A. N.

1990-01-01

The use of a multiple pulse testing technique to determine the electrical characteristics of large megawatt-level power systems for aerospace missions is proposed. An innovative test method based on the multiple pulse technique is demonstrated on a 2-kW Mapham inverter. The concept of this technique shows that characterization of large power systems under electrical equilibrium at rated power can be accomplished without large costly power supplies. The heat generation that occurs in systems when tested in a continuous mode is eliminated. The results indicate that there is a good agreement between this testing technique and that of steady state testing.

Large Payload Transportation and Test Considerations

NASA Technical Reports Server (NTRS)

Rucker, Michelle A.; Pope, James C.

2011-01-01

Ironically, the limiting factor to a national heavy lift strategy may not be the rocket technology needed to throw a heavy payload, but rather the terrestrial infrastructure - roads, bridges, airframes, and buildings - necessary to transport, acceptance test, and process large spacecraft. Failure to carefully consider how large spacecraft are designed, and where they are manufactured, tested, or launched, could result in unforeseen cost to modify/develop infrastructure, or incur additional risk due to increased handling or elimination of key verifications. During test and verification planning for the Altair project, a number of transportation and test issues related to the large payload diameter were identified. Although the entire Constellation Program - including Altair - was canceled in the 2011 NASA budget, issues identified by the Altair project serve as important lessons learned for future payloads that may be developed to support national "heavy lift" strategies. A feasibility study performed by the Constellation Ground Operations (CxGO) project found that neither the Altair Ascent nor Descent Stage would fit inside available transportation aircraft. Ground transportation of a payload this large over extended distances is generally not permitted by most states, so overland transportation alone would not have been an option. Limited ground transportation to the nearest waterway may be permitted, but water transportation could take as long as 66 days per production unit, depending on point of origin and acceptance test facility; transportation from the western United States would require transit through the Panama Canal to access the Kennedy Space Center launch site. Large payloads also pose acceptance test and ground processing challenges. Although propulsion, mechanical vibration, and reverberant acoustic test facilities at NASA s Plum Brook Station have been designed to accommodate large spacecraft, special handling and test work-arounds may be necessary, which could increase cost, schedule, and technical risk. Once at the launch site, there are no facilities currently capable of accommodating the combination of large payload size and hazardous processing (which includes hypergolic fuels, pyrotechnic devices, and high pressure gasses).

Quality Control for Scoring Tests Administered in Continuous Mode: An NCME Instructional Module

ERIC Educational Resources Information Center

Allalouf, Avi; Gutentag, Tony; Baumer, Michal

2017-01-01

Quality control (QC) in testing is paramount. QC procedures for tests can be divided into two types. The first type, one that has been well researched, is QC for tests administered to large population groups on few administration dates using a small set of test forms (e.g., large-scale assessment). The second type is QC for tests, usually…

Personality Measurement and Assessment in Large Panel Surveys*

PubMed Central

Roberts, Brent; Jackson, Joshua J.; Duckworth, Angela L.; Von Culin, Katherine

2013-01-01

Personality tests are being added to large panel studies with increasing regularity, such as the Health and Retirement Study (HRS). To facilitate the inclusion and interpretation of these tests, we provide some general background on personality psychology, personality assessment, and the validity of personality tests. In this review, we provide background on definitions of personality, the strengths and weaknesses of the self-report approaches to personality testing typically used in large panel studies, and the validity of personality tests for three outcomes: genetics, income, and health. We conclude with recommendations on how to improve personality assessment in future panel studies. PMID:23503719

Internet cognitive testing of large samples needed in genetic research.

PubMed

Haworth, Claire M A; Harlaar, Nicole; Kovas, Yulia; Davis, Oliver S P; Oliver, Bonamy R; Hayiou-Thomas, Marianna E; Frances, Jane; Busfield, Patricia; McMillan, Andrew; Dale, Philip S; Plomin, Robert

2007-08-01

Quantitative and molecular genetic research requires large samples to provide adequate statistical power, but it is expensive to test large samples in person, especially when the participants are widely distributed geographically. Increasing access to inexpensive and fast Internet connections makes it possible to test large samples efficiently and economically online. Reliability and validity of Internet testing for cognitive ability have not been previously reported; these issues are especially pertinent for testing children. We developed Internet versions of reading, language, mathematics and general cognitive ability tests and investigated their reliability and validity for 10- and 12-year-old children. We tested online more than 2500 pairs of 10-year-old twins and compared their scores to similar internet-based measures administered online to a subsample of the children when they were 12 years old (> 759 pairs). Within 3 months of the online testing at 12 years, we administered standard paper and pencil versions of the reading and mathematics tests in person to 30 children (15 pairs of twins). Scores on Internet-based measures at 10 and 12 years correlated .63 on average across the two years, suggesting substantial stability and high reliability. Correlations of about .80 between Internet measures and in-person testing suggest excellent validity. In addition, the comparison of the internet-based measures to ratings from teachers based on criteria from the UK National Curriculum suggests good concurrent validity for these tests. We conclude that Internet testing can be reliable and valid for collecting cognitive test data on large samples even for children as young as 10 years.

[Research on adaptive quasi-linear viscoelastic model for nonlinear viscoelastic properties of in vivo soft tissues].

PubMed

Wang, Heng; Sang, Yuanjun

2017-10-01

The mechanical behavior modeling of human soft biological tissues is a key issue for a large number of medical applications, such as surgery simulation, surgery planning, diagnosis, etc. To develop a biomechanical model of human soft tissues under large deformation for surgery simulation, the adaptive quasi-linear viscoelastic (AQLV) model was proposed and applied in human forearm soft tissues by indentation tests. An incremental ramp-and-hold test was carried out to calibrate the model parameters. To verify the predictive ability of the AQLV model, the incremental ramp-and-hold test, a single large amplitude ramp-and-hold test and a sinusoidal cyclic test at large strain amplitude were adopted in this study. Results showed that the AQLV model could predict the test results under the three kinds of load conditions. It is concluded that the AQLV model is feasible to describe the nonlinear viscoelastic properties of in vivo soft tissues under large deformation. It is promising that this model can be selected as one of the soft tissues models in the software design for surgery simulation or diagnosis.

Aquatic Plant Control Research Program. Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 5. Synthesis Report.

DTIC Science & Technology

1984-06-01

RD-Rl45 988 AQUATIC PLANT CONTROL RESEARCH PROGRAM LARGE-SCALE 1/2 OPERATIONS MANAGEMENT ..(U) ARMY ENGINEER WATERWAYS EXPERIMENT STATION VICKSBURG MS...REPORT A-78-2 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR -, CONTROL OF PROBLEM AQUATIC PLANTS Report 5 SYNTHESIS REPORT bv Andrew...Corps of Engineers Washington, DC 20314 84 0,_1 oil.. LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC

Sub-aperture stitching test of a cylindrical mirror with large aperture

NASA Astrophysics Data System (ADS)

Xue, Shuai; Chen, Shanyong; Shi, Feng; Lu, Jinfeng

2016-09-01

Cylindrical mirrors are key optics of high-end equipment of national defense and scientific research such as high energy laser weapons, synchrotron radiation system, etc. However, its surface error test technology develops slowly. As a result, its optical processing quality can not meet the requirements, and the developing of the associated equipment is hindered. Computer Generated-Hologram (CGH) is commonly utilized as null for testing cylindrical optics. However, since the fabrication process of CGH with large aperture is not sophisticated yet, the null test of cylindrical optics with large aperture is limited by the aperture of the CGH. Hence CGH null test combined with sub-aperture stitching method is proposed to break the limit of the aperture of CGH for testing cylindrical optics, and the design of CGH for testing cylindrical surfaces is analyzed. Besides, the misalignment aberration of cylindrical surfaces is different from that of the rotational symmetric surfaces since the special shape of cylindrical surfaces, and the existing stitching algorithm of rotational symmetric surfaces can not meet the requirements of stitching cylindrical surfaces. We therefore analyze the misalignment aberrations of cylindrical surfaces, and study the stitching algorithm for measuring cylindrical optics with large aperture. Finally we test a cylindrical mirror with large aperture to verify the validity of the proposed method.

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume IV. Nitrogen and Phosphorus Dynamics of the Lake Conway Ecosystem: Loading Budgets and a Dynamic Hydrologic Phosphorus Model.

DTIC Science & Technology

1982-08-01

AD-AIA 700 FLORIDA UN1V GAINESVILLE DEPT OF ENVIRONMENTAL ENGIN -ETC F/G 6/6 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMOR--ENL...Conway ecosystem and is part of the Large- Scale Operations Management Test (LSOMT) of the Aquatic Plant Control Research Program (APCRP) at the WES...should be cited as follows: Blancher, E. C., II, and Fellows, C. R. 1982. "Large-Scale Operations Management Test of Use of the White Amur for Control

Aquatic Plant Control Research Program. Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Reports 2 and 3. First and Second Year Poststocking Results. Volume 5. The Herpetofauna of Lake Conway, Florida: Community Analysis.

DTIC Science & Technology

1983-07-01

TEST CHART NATIONAL BVIREAU OF StANARS-1963- I AQUATIC PLANT CONTROL RESEARCH PROGRAM TECHNICAL REPORT A-78-2 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF...Waterways Experiment Station P. 0. Box 631, Vicksburg, Miss. 39180 83 11 01 018 - I ., lit I III I | LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE...No. 3. RECIPIENT’S CATALOG NUMBER Technical Report A-78-2 Aa 1 Lj 19 ________5!1___ A. TITLE (Ad Subtitle) LARGE-SCALE OPERATIONS MANAGEMENT S. TYPE

The development of large-aperture test system of infrared camera and visible CCD camera

NASA Astrophysics Data System (ADS)

Li, Yingwen; Geng, Anbing; Wang, Bo; Wang, Haitao; Wu, Yanying

2015-10-01

Infrared camera and CCD camera dual-band imaging system is used in many equipment and application widely. If it is tested using the traditional infrared camera test system and visible CCD test system, 2 times of installation and alignment are needed in the test procedure. The large-aperture test system of infrared camera and visible CCD camera uses the common large-aperture reflection collimator, target wheel, frame-grabber, computer which reduces the cost and the time of installation and alignment. Multiple-frame averaging algorithm is used to reduce the influence of random noise. Athermal optical design is adopted to reduce the change of focal length location change of collimator when the environmental temperature is changing, and the image quality of the collimator of large field of view and test accuracy are also improved. Its performance is the same as that of the exotic congener and is much cheaper. It will have a good market.

An overview of large wind turbine tests by electric utilities

NASA Technical Reports Server (NTRS)

Vachon, W. A.; Schiff, D.

1982-01-01

A summary of recent plants and experiences on current large wind turbine (WT) tests being conducted by electric utilities is provided. The test programs discussed do not include federal research and development (R&D) programs, many of which are also being conducted in conjunction with electric utilities. The information presented is being assembled in a project, funded by the Electric Power Research Institute (EPRI), the objective of which is to provide electric utilities with timely summaries of test performance on key large wind turbines. A summary of key tests, test instrumentation, and recent results and plans is given. During the past year, many of the utility test programs initiated have encountered test difficulties that required specific WT design changes. However, test results to date continue to indicate that long-term machine performance and cost-effectiveness are achievable.

Indoor test for the thermal performance evaluation of the DEC 8A large manifold sunmaster evacuated tube (liquid) solar collector

NASA Technical Reports Server (NTRS)

1981-01-01

The Sunmaster DEC 8A Large Manifold solar collector using simulated conditions was evaluated. The collector provided 17.17 square feet of gross collector area. Test conditions, test requirements, an analysis of results, and tables of test data are reported.

Gas-Centered Swirl Coaxial Liquid Injector Evaluations

NASA Technical Reports Server (NTRS)

Cohn, A. K.; Strakey, P. A.; Talley, D. G.

2005-01-01

Development of Liquid Rocket Engines is expensive. Extensive testing at large scales usually required. In order to verify engine lifetime, large number of tests required. Limited Resources available for development. Sub-scale cold-flow and hot-fire testing is extremely cost effective. Could be a necessary (but not sufficient) condition for long engine lifetime. Reduces overall costs and risk of large scale testing. Goal: Determine knowledge that can be gained from sub-scale cold-flow and hot-fire evaluations of LRE injectors. Determine relationships between cold-flow and hot-fire data.

Measurement of external forces and torques on a large pointing system

NASA Technical Reports Server (NTRS)

Morenus, R. C.

1980-01-01

Methods of measuring external forces and torques are discussed, in general and as applied to the Large Pointing System wind tunnel tests. The LPS tests were in two phases. The first test was a preliminary test of three models representing coelostat, heliostat, and on-gimbal telescope configurations. The second test explored the coelostat configuration in more detail. The second test used a different setup for measuring external loads. Some results are given from both tests.

Large Payload Ground Transportation and Test Considerations

NASA Technical Reports Server (NTRS)

Rucker, Michelle A.

2016-01-01

Many spacecraft concepts under consideration by the National Aeronautics and Space Administration’s (NASA’s) Evolvable Mars Campaign take advantage of a Space Launch System payload shroud that may be 8 to 10 meters in diameter. Large payloads can theoretically save cost by reducing the number of launches needed--but only if it is possible to build, test, and transport a large payload to the launch site in the first place. Analysis performed previously for the Altair project identified several transportation and test issues with an 8.973 meters diameter payload. Although the entire Constellation Program—including Altair—has since been canceled, these issues serve as important lessons learned for spacecraft designers and program managers considering large payloads for future programs. A transportation feasibility study found that, even broken up into an Ascent and Descent Module, the Altair spacecraft would not fit inside available aircraft. Ground transportation of such large payloads over extended distances is not generally permitted, so overland transportation alone would not be an option. Limited ground transportation to the nearest waterway may be possible, but water transportation could take as long as 67 days per production unit, depending on point of origin and acceptance test facility; transportation from the western United States would require transit through the Panama Canal to access the Kennedy Space Center launch site. Large payloads also pose acceptance test and ground processing challenges. Although propulsion, mechanical vibration, and reverberant acoustic test facilities at NASA’s Plum Brook Station have been designed to accommodate large spacecraft, special handling and test work-arounds may be necessary, which could increase cost, schedule, and technical risk. Once at the launch site, there are no facilities currently capable of accommodating the combination of large payload size and hazardous processing such as hypergolic fuels, pyrotechnic devices, and high pressure gasses. Ironically, the limiting factor to a national heavy lift strategy may not be the rocket technology needed to throw a heavy payload, but rather the terrestrial infrastructure—roads, bridges, airframes, and buildings—necessary to transport, acceptance test, and process large spacecraft. Failure to carefully consider where and how large spacecraft are manufactured, tested, and launched could result in unforeseen cost to modify existing (or develop new) infrastructure, or incur additional risk due to increased handling operations or eliminating key verifications. Although this paper focuses on the canceled Altair spacecraft as a case study, the issues identified here have wide applicability to other large payloads, including concepts under consideration for NASA’s Evolvable Mars Campaign.

Large-scale wind tunnel tests of a sting-supported V/STOL fighter model at high angles of attack

NASA Technical Reports Server (NTRS)

Stoll, F.; Minter, E. A.

1981-01-01

A new sting model support has been developed for the NASA/Ames 40- by 80-Foot Wind Tunnel. This addition to the facility permits testing of relatively large models to large angles of attack or angles of yaw depending on model orientation. An initial test on the sting is described. This test used a 0.4-scale powered V/STOL model designed for testing at angles of attack to 90 deg and greater. A method for correcting wake blockage was developed and applied to the force and moment data. Samples of this data and results of surface-pressure measurements are presented.

5. Credit BG. View looking northwest at eastern facade of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Credit BG. View looking northwest at eastern facade of Test Stand 'E' (Building 4259/E-60), solid rocket motor test facility. Central bay (high concrete walls) was used for testing large solid motors in a vertical position. A second smaller bay to the north fired smaller motors horizontally. Just south of the large bay is an equipment room with access to the tunnel system; entrance is by small single door on east side. The large double doors lead to a third bay used for X-raying solid rocket motors before testing. - Jet Propulsion Laboratory Edwards Facility, Test Stand E, Edwards Air Force Base, Boron, Kern County, CA

Dynamic test/analysis correlation using reduced analytical models

NASA Technical Reports Server (NTRS)

Mcgowan, Paul E.; Angelucci, A. Filippo; Javeed, Mehzad

1992-01-01

Test/analysis correlation is an important aspect of the verification of analysis models which are used to predict on-orbit response characteristics of large space structures. This paper presents results of a study using reduced analysis models for performing dynamic test/analysis correlation. The reduced test-analysis model (TAM) has the same number and orientation of DOF as the test measurements. Two reduction methods, static (Guyan) reduction and the Improved Reduced System (IRS) reduction, are applied to the test/analysis correlation of a laboratory truss structure. Simulated test results and modal test data are used to examine the performance of each method. It is shown that selection of DOF to be retained in the TAM is critical when large structural masses are involved. In addition, the use of modal test results may provide difficulties in TAM accuracy even if a large number of DOF are retained in the TAM.

Preparing to Test

NASA Image and Video Library

2015-03-26

Stennis Space Center employees install a 96-inch valve during a recent upgrade of the high-pressure industrial water system that serves the site’s large rocket engine test stands. The upgraded system has a capacity to flow 335,000 gallons of water a minute, which is a critical element for testing. At Stennis, engines are anchored in place on large test stands and fired just as they are during an actual space flight. The fire and exhaust from the test is redirected out of the stand by a large flame trench. A water deluge system directs thousands of gallons of water needed to cool the exhaust. Water also must be available for fire suppression in the event of a mishap. The new system supports RS-25 engine testing on the A-1 Test Stand, as well as testing of the core stage of NASA’s new Space Launch System on the B-2 Test Stand at Stennis.

Overview of drug and alcohol use among large truck and bus drivers, 2011–13.

DOT National Transportation Integrated Search

2016-12-01

This report provides a broad overview of drug and alcohol usage among large truck and bus drivers for 201113. Data sources for the overview are: testing results from motor carrier drug testing programs, roadside inspections on large trucks and bus...

Fabrication, Testing, Coating and Alignment of Fast Segmented Optics

DTIC Science & Technology

2006-05-25

mirror segment, a 100 mm thick Zerodur mirror blank was purchased from Schott. Figure 2 shows the segment and its support for polishing and testing in...Polishing large off-axis segments of fast primary mirrors 2. Testing large segments in an off-axis geometry 3. Alignment of multiple segments of a large... mirror 4. Coatings that reflect high-intensity light without distorting the substrate These technologies are critical because of several unique

Icing Simulation Research Supporting the Ice-Accretion Testing of Large-Scale Swept-Wing Models

NASA Technical Reports Server (NTRS)

Yadlin, Yoram; Monnig, Jaime T.; Malone, Adam M.; Paul, Bernard P.

2018-01-01

The work summarized in this report is a continuation of NASA's Large-Scale, Swept-Wing Test Articles Fabrication; Research and Test Support for NASA IRT contract (NNC10BA05 -NNC14TA36T) performed by Boeing under the NASA Research and Technology for Aerospace Propulsion Systems (RTAPS) contract. In the study conducted under RTAPS, a series of icing tests in the Icing Research Tunnel (IRT) have been conducted to characterize ice formations on large-scale swept wings representative of modern commercial transport airplanes. The outcome of that campaign was a large database of ice-accretion geometries that can be used for subsequent aerodynamic evaluation in other experimental facilities and for validation of ice-accretion prediction codes.

Hybrid Computerized Adaptive Testing: From Group Sequential Design to Fully Sequential Design

ERIC Educational Resources Information Center

Wang, Shiyu; Lin, Haiyan; Chang, Hua-Hua; Douglas, Jeff

2016-01-01

Computerized adaptive testing (CAT) and multistage testing (MST) have become two of the most popular modes in large-scale computer-based sequential testing. Though most designs of CAT and MST exhibit strength and weakness in recent large-scale implementations, there is no simple answer to the question of which design is better because different…

An antenna pointing mechanism for large reflector antennas

NASA Technical Reports Server (NTRS)

Heimerdinger, H.

1981-01-01

An antenna pointing mechanism for large reflector antennas on direct broadcasting communication satellites was built and tested. After listing the requirements and constraints for this equipment the model is described, and performance figures are given. Futhermore, results of the qualification level tests, including functional, vibrational, thermovacuum, and accelerated life tests are reported. These tests were completed successfully.

Self-consistency tests of large-scale dynamics parameterizations for single-column modeling

DOE PAGES

Edman, Jacob P.; Romps, David M.

2015-03-18

Large-scale dynamics parameterizations are tested numerically in cloud-resolving simulations, including a new version of the weak-pressure-gradient approximation (WPG) introduced by Edman and Romps (2014), the weak-temperature-gradient approximation (WTG), and a prior implementation of WPG. We perform a series of self-consistency tests with each large-scale dynamics parameterization, in which we compare the result of a cloud-resolving simulation coupled to WTG or WPG with an otherwise identical simulation with prescribed large-scale convergence. In self-consistency tests based on radiative-convective equilibrium (RCE; i.e., no large-scale convergence), we find that simulations either weakly coupled or strongly coupled to either WPG or WTG are self-consistent, butmore » WPG-coupled simulations exhibit a nonmonotonic behavior as the strength of the coupling to WPG is varied. We also perform self-consistency tests based on observed forcings from two observational campaigns: the Tropical Warm Pool International Cloud Experiment (TWP-ICE) and the ARM Southern Great Plains (SGP) Summer 1995 IOP. In these tests, we show that the new version of WPG improves upon prior versions of WPG by eliminating a potentially troublesome gravity-wave resonance.« less

Fracture Testing of Large-Scale Thin-Sheet Aluminum Alloy (MS Word file)

DOT National Transportation Integrated Search

1996-02-01

Word Document; A series of fracture tests on large-scale, precracked, aluminum alloy panels were carried out to examine and characterize the process by which cracks propagate and link up in this material. Extended grips and test fixtures were special...

49 CFR 178.970 - Bottom lift test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Large Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... permissible gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types...

Transient and Steady-state Tests of the Space Power Research Engine with Resistive and Motor Loads

NASA Technical Reports Server (NTRS)

Rauch, Jeffrey S.; Kankam, M. David

1995-01-01

The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

Transient and steady-state tests of the space power research engine with resistive and motor loads

NASA Astrophysics Data System (ADS)

Rauch, Jeffrey S.; Kankam, M. David

1995-01-01

The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

TESTING PRACTICES AND VOLUME OF NON-LYME TICKBORNE DISEASES IN THE UNITED STATES

PubMed Central

Connally, Neeta P.; Hinckley, Alison F.; Feldman, Katherine A.; Kemperman, Melissa; Neitzel, David; Wee, Siok-Bi; White, Jennifer L.; Mead, Paul S.; Meek, James I.

2015-01-01

Large commercial laboratories in the United States were surveyed regarding the number of specimens tested for eight tickborne diseases in 2008. Seven large commercial laboratories reported testing a total of 2,927,881 specimens nationally (including Lyme disease). Of these, 495,585 specimens (17 percent) were tested for tickborne diseases other than Lyme disease. In addition to large commercial laboratories, another 1,051 smaller commercial, hospital, and government laboratories in four states (CT, MD, MN, and NY) were surveyed regarding tickborne disease testing frequency, practices, and results. Ninety-two of these reported testing a total of 10,091 specimens for four tickborne diseases other than Lyme disease. We estimate the cost of laboratory diagnostic testing for non-Lyme disease tickborne diseases in 2008 to be $9.6 million. These data provide a baseline to evaluate trends in tickborne disease test utilization and insight into the burden of these diseases. PMID:26565931

Large Payload Ground Transportation and Test Considerations

NASA Technical Reports Server (NTRS)

Rucker, Michelle A.

2016-01-01

During test and verification planning for the Altair lunar lander project, a National Aeronautics and Space Administration (NASA) study team identified several ground transportation and test issues related to the large payload diameter. Although the entire Constellation Program-including Altair-has since been canceled, issues identified by the Altair project serve as important lessons learned for payloads greater than 7 m diameter being considered for NASA's new Space Launch System (SLS). A transportation feasibility study found that Altair's 8.97 m diameter Descent Module would not fit inside available aircraft. Although the Ascent Module cabin was only 2.35 m diameter, the long reaction control system booms extended nearly to the Descent Module diameter, making it equally unsuitable for air transportation without removing the booms and invalidating assembly workmanship screens or acceptance testing that had already been performed. Ground transportation of very large payloads over extended distances is not generally permitted by most states, so overland transportation alone would not be an option. Limited ground transportation to the nearest waterway may be possible, but water transportation could take as long as 66 days per production unit, depending on point of origin and acceptance test facility; transportation from the western United States would require transit through the Panama Canal to access the Kennedy Space Center launch site. Large payloads also pose acceptance test and ground processing challenges. Although propulsion, mechanical vibration, and reverberant acoustic test facilities at NASA's Plum Brook Station have been designed to accommodate large spacecraft, special handling and test work-arounds may be necessary, which could increase cost, schedule, and technical risk. Once at the launch site, there are no facilities currently capable of accommodating the combination of large payload size and hazardous processing such as hypergolic fuels, pyrotechnic devices, and high pressure gasses. Ironically, the limiting factor to a national heavy lift strategy may not be the rocket technology needed to throw a heavy payload, but rather the terrestrial infrastructure-roads, bridges, airframes, and buildings-necessary to transport, acceptance test, and process large spacecraft. Failure to carefully consider where and how large spacecraft are manufactured, tested, and launched could result in unforeseen cost to modify existing (or develop new) infrastructure, or incur additional risk due to increased handling operations or eliminating key verifications.

Stereotype Threat, Inquiring about Test Takers' Race and Gender, and Performance on Low-Stakes Tests in a Large-Scale Assessment. Research Report. ETS RR-15-02

ERIC Educational Resources Information Center

Stricker, Lawrence J.; Rock, Donald A.; Bridgeman, Brent

2015-01-01

This study explores stereotype threat on low-stakes tests used in a large-scale assessment, math and reading tests in the Education Longitudinal Study of 2002 (ELS). Issues identified in laboratory research (though not observed in studies of high-stakes tests) were assessed: whether inquiring about their race and gender is related to the…

Haz-Map Glossary

MedlinePlus

... lung. Radiation Accident Large-scale accidents from atomic bomb testing fallout released iodine-131 and strontium-90. ... lung. Radiation Accident Large-scale accidents from atomic bomb testing fallout released iodine-131 and strontium-90. ...

Gravitational lenses and large scale structure

NASA Technical Reports Server (NTRS)

Turner, Edwin L.

1987-01-01

Four possible statistical tests of the large scale distribution of cosmic material are described. Each is based on gravitational lensing effects. The current observational status of these tests is also summarized.

Experimental feasibility study of the application of magnetic suspension techniques to large-scale aerodynamic test facilities

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1974-01-01

Based on the premises that (1) magnetic suspension techniques can play a useful role in large-scale aerodynamic testing and (2) superconductor technology offers the only practical hope for building large-scale magnetic suspensions, an all-superconductor three-component magnetic suspension and balance facility was built as a prototype and was tested successfully. Quantitative extrapolations of design and performance characteristics of this prototype system to larger systems compatible with existing and planned high Reynolds number facilities have been made and show that this experimental technique should be particularly attractive when used in conjunction with large cryogenic wind tunnels.

Experimental feasibility study of the application of magnetic suspension techniques to large-scale aerodynamic test facilities. [cryogenic traonics wind tunnel

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1975-01-01

Based on the premises that magnetic suspension techniques can play a useful role in large scale aerodynamic testing, and that superconductor technology offers the only practical hope for building large scale magnetic suspensions, an all-superconductor 3-component magnetic suspension and balance facility was built as a prototype and tested sucessfully. Quantitative extrapolations of design and performance characteristics of this prototype system to larger systems compatible with existing and planned high Reynolds number facilities at Langley Research Center were made and show that this experimental technique should be particularly attractive when used in conjunction with large cryogenic wind tunnels.

Proceedings of the Annual Meeting (14th) Aquatic Plant Control Research Planning and Operations Review, Held at Lake Eufaula, Oklahoma on 26-29 November 1979.

DTIC Science & Technology

1980-10-01

Development; Problem Identification and Assessment for Aquatic Plant Management; Natural Succession of Aquatic Plants; Large-Scale Operations Management Test...of Insects and Pathogens for Control of Waterhyacinth in Louisiana; Large-Scale Operations Management Test to Evaluate Prevention Methodology for...Control of Eurasian Watermilfoil in Washington; Large-Scale Operations Management Test Using the White Amur at Lake Conway, Florida; and Aquatic Plant Control Activities in the Panama Canal Zone.

The Expanded Large Scale Gap Test

DTIC Science & Technology

1987-03-01

NSWC TR 86-32 DTIC THE EXPANDED LARGE SCALE GAP TEST BY T. P. LIDDIARD D. PRICE RESEARCH AND TECHNOLOGY DEPARTMENT ’ ~MARCH 1987 Ap~proved for public...arises, to reduce the spread in the LSGT 50% gap value.) The worst charges, such as those with the highest or lowest densities, the largest re-pressed...Arlington, VA 22217 PE 62314N INS3A 1 RJ14E31 7R4TBK 11 TITLE (Include Security CIlmsilficatiorn The Expanded Large Scale Gap Test . 12. PEIRSONAL AUTHOR() T

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume III. The Plankton and Benthos of Lake Conway, Florida,

DTIC Science & Technology

1981-11-01

AD-AI09 516 FLORIDA UNIV GAINESVILLE DEPT OF ENVIRONMENTAL ENGIN--ETC F/G 6/6 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE,WHITE AMUR--ETC(U... OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC PLANTS Report I: Baseline Studies Volume I: The Aquatic Macropyes of...COVERED LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF Report 2 of a series THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC (In 7 volumes) PLANTS

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 3. Second Year Poststocking Results. Volume VI. The Water and Sediment Quality of Lake Conway, Florida.

DTIC Science & Technology

1982-08-01

AD-A-11 701 ORANGE COUNTY POLLUTION CONTROL DEPT ORLANDO FL F/0 6/6 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR--ETC(U) AUG 82 H...8217 OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL -OF PROBLEM AQ.UATIC PLANTS SECOND YEAR POSTSTOCKING RESULTS Volume, Vt The Water...and Subetie) S. TYPE OF REPORT & PERIOD COVERED LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF Report 3 of a series THE WHITE AMUR FOR CONTROL OF

Summary of the First High-Altitude, Supersonic Flight Dynamics Test for the Low-Density Supersonic Decelerator Project

NASA Technical Reports Server (NTRS)

Clark, Ian G.; Adler, Mark; Manning, Rob

2015-01-01

NASA's Low-Density Supersonic Decelerator Project is developing and testing the next generation of supersonic aerodynamic decelerators for planetary entry. A key element of that development is the testing of full-scale articles in conditions relevant to their intended use, primarily the tenuous Mars atmosphere. To achieve this testing, the LDSD project developed a test architecture similar to that used by the Viking Project in the early 1970's for the qualification of their supersonic parachute. A large, helium filled scientific balloon is used to hoist a 4.7 m blunt body test vehicle to an altitude of approximately 32 kilometers. The test vehicle is released from the balloon, spun up for gyroscopic stability, and accelerated to over four times the speed of sound and an altitude of 50 kilometers using a large solid rocket motor. Once at those conditions, the vehicle is despun and the test period begins. The first flight of this architecture occurred on June 28th of 2014. Though primarily a shake out flight of the new test system, the flight was also able to achieve an early test of two of the LDSD technologies, a large 6 m diameter Supersonic Inflatable Aerodynamic Decelerator (SIAD) and a large, 30.5 m nominal diameter supersonic parachute. This paper summarizes this first flight.

Reliability and Validity of Information about Student Achievement: Comparing Large-Scale and Classroom Testing Contexts

ERIC Educational Resources Information Center

Cizek, Gregory J.

2009-01-01

Reliability and validity are two characteristics that must be considered whenever information about student achievement is collected. However, those characteristics--and the methods for evaluating them--differ in large-scale testing and classroom testing contexts. This article presents the distinctions between reliability and validity in the two…

Dynamics of the McDonnell Douglas Large Scale Dynamic Rig and Dynamic Calibration of the Rotor Balance

DOT National Transportation Integrated Search

1994-10-01

A shake test was performed on the Large Scale Dynamic Rig in the 40- by 80-Foot Wind Tunnel in support of the McDonnell Douglas Advanced Rotor Technology (MDART) Test Program. The shake test identifies the hub modes and the dynamic calibration matrix...

Developing a Strategy for Using Technology-Enhanced Items in Large-Scale Standardized Tests

ERIC Educational Resources Information Center

Bryant, William

2017-01-01

As large-scale standardized tests move from paper-based to computer-based delivery, opportunities arise for test developers to make use of items beyond traditional selected and constructed response types. Technology-enhanced items (TEIs) have the potential to provide advantages over conventional items, including broadening construct measurement,…

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cubic meters (175 cubic feet) tank

NASA Technical Reports Server (NTRS)

Taylor, William J.; Chato, David J.

1993-01-01

The NASA Lewis Research Center (NASA/LeRC) have been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 m and 0.142 cubic m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 cubic m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to over predict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Cost estimate for a proposed GDF Suez LNG testing program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blanchat, Thomas K.; Brady, Patrick Dennis; Jernigan, Dann A.

2014-02-01

At the request of GDF Suez, a Rough Order of Magnitude (ROM) cost estimate was prepared for the design, construction, testing, and data analysis for an experimental series of large-scale (Liquefied Natural Gas) LNG spills on land and water that would result in the largest pool fires and vapor dispersion events ever conducted. Due to the expected cost of this large, multi-year program, the authors utilized Sandia's structured cost estimating methodology. This methodology insures that the efforts identified can be performed for the cost proposed at a plus or minus 30 percent confidence. The scale of the LNG spill, fire,more » and vapor dispersion tests proposed by GDF could produce hazard distances and testing safety issues that need to be fully explored. Based on our evaluations, Sandia can utilize much of our existing fire testing infrastructure for the large fire tests and some small dispersion tests (with some modifications) in Albuquerque, but we propose to develop a new dispersion testing site at our remote test area in Nevada because of the large hazard distances. While this might impact some testing logistics, the safety aspects warrant this approach. In addition, we have included a proposal to study cryogenic liquid spills on water and subsequent vaporization in the presence of waves. Sandia is working with DOE on applications that provide infrastructure pertinent to wave production. We present an approach to conduct repeatable wave/spill interaction testing that could utilize such infrastructure.« less

Testing practices and volume of non-Lyme tickborne diseases in the United States.

PubMed

Connally, Neeta P; Hinckley, Alison F; Feldman, Katherine A; Kemperman, Melissa; Neitzel, David; Wee, Siok-Bi; White, Jennifer L; Mead, Paul S; Meek, James I

2016-02-01

Large commercial laboratories in the United States were surveyed regarding the number of specimens tested for eight tickborne diseases in 2008. Seven large commercial laboratories reported testing a total of 2,927,881 specimens nationally (including Lyme disease). Of these, 495,585 specimens (17%) were tested for tickborne diseases other than Lyme disease. In addition to large commercial laboratories, another 1051 smaller commercial, hospital, and government laboratories in four states (CT, MD, MN, and NY) were surveyed regarding tickborne disease testing frequency, practices, and results. Ninety-two of these reported testing a total of 10,091 specimens for four tickborne diseases other than Lyme disease. We estimate the cost of laboratory diagnostic testing for non-Lyme disease tickborne diseases in 2008 to be $9.6 million. These data provide a baseline to evaluate trends in tickborne disease test utilization and insight into the burden of these diseases. Copyright © 2015 Elsevier GmbH. All rights reserved.

Metrology of Large Parts. Chapter 5

NASA Technical Reports Server (NTRS)

Stahl, H. Philip

2012-01-01

As discussed in the first chapter of this book, there are many different methods to measure a part using optical technology. Chapter 2 discussed the use of machine vision to measure macroscopic features such as length and position, which was extended to the use of interferometry as a linear measurement tool in chapter 3, and laser or other trackers to find the relation of key points on large parts in chapter 4. This chapter looks at measuring large parts to optical tolerances in the sub-micron range using interferometry, ranging, and optical tools discussed in the previous chapters. The purpose of this chapter is not to discuss specific metrology tools (such as interferometers or gauges), but to describe a systems engineering approach to testing large parts. Issues such as material warpage and temperature drifts that may be insignificant when measuring a part to micron levels under a microscope, as will be discussed in later chapters, can prove to be very important when making the same measurement over a larger part. In this chapter, we will define a set of guiding principles for successfully overcoming these challenges and illustrate the application of these principles with real world examples. While these examples are drawn from specific large optical testing applications, they inform the problems associated with testing any large part to optical tolerances. Manufacturing today relies on micrometer level part performance. Fields such as energy and transportation are demanding higher tolerances to provide increased efficiencies and fuel savings. By looking at how the optics industry approaches sub-micrometer metrology, one can gain a better understanding of the metrology challenges for any larger part specified to micrometer tolerances. Testing large parts, whether optical components or precision structures, to optical tolerances is just like testing small parts, only harder. Identical with what one does for small parts, a metrologist tests large parts and optics in particular to quantify their mechanical properties (such as dimensions, mass, etc); their optical prescription or design (i.e. radius of curvature, conic constant, vertex location, size); and their full part shape. And, just as with small parts, a metrologist accomplishes these tests using distance measuring instruments such as tape measures, inside micrometers, coordinate measuring machines, distance measuring interferometers; angle measuring instruments such as theodolites, autocollimators; and surface measuring instruments including interferometers, stylus profilers, interference microscopes, photogrammetric cameras, or other tools. However, while the methodology may be similar, it is more difficult to test a large object for the simple reason that most metrologists do not have the necessary intuition. The skills used to test small parts or optics in a laboratory do not extrapolate to testing large parts in an industrial setting any more than a backyard gardener might successfully operate a farm. But first, what is a large part? A simple definition might be the part's size or diameter. For optics and diffuse surface parts alike, the driving constraint is ability to illuminate the part's surface. For reflective convex mirrors, large is typically anything greater than 1 meter. But, for refractive optics, flats or convex mirrors, large is typically greater than 0.5 meter. While a size definition is simple, it may be less than universal. A more nuanced definition might be that a large part is any component which cannot be easily tested in a standard laboratory environment, on a standard vibration isolated table using standard laboratory infrastructure. A micro-switch or a precision lens might be easily measured to nanometer levels under a microscope in a lab, but a power turbine spline or a larger telescope mirror will not fit under that microscope and may not even fit on the table.

A Metallurgical Investigation of Large Forged Discs of Low-carbon N-155 Alloy

NASA Technical Reports Server (NTRS)

Cross, Howard C; Freeman, J W

1947-01-01

Research was undertaken to ascertain the properties of better wrought heat resisting alloys in the form of large discs required for gas turbine rotors. The properties of large discs of low carbon N-155 alloy in both the as-forged and water-quenched and aged conditions were determined by means of stress-rupture and creep tests for time periods up to about 2000 hours at 1200, 1350, and 1500 F. Short-time tensile test, impact test, and time-total deformation characteristics are included. The principle results are given.

Definition of technology development missions for early space stations: Large space structures

NASA Technical Reports Server (NTRS)

1983-01-01

The testbed role of an early (1990-95) manned space station in large space structures technology development is defined and conceptual designs for large space structures development missions to be conducted at the space station are developed. Emphasis is placed on defining requirements and benefits of development testing on a space station in concert with ground and shuttle tests.

Large-Scale Hybrid Motor Testing. Chapter 10

NASA Technical Reports Server (NTRS)

Story, George

2006-01-01

Hybrid rocket motors can be successfully demonstrated at a small scale virtually anywhere. There have been many suitcase sized portable test stands assembled for demonstration of hybrids. They show the safety of hybrid rockets to the audiences. These small show motors and small laboratory scale motors can give comparative burn rate data for development of different fuel/oxidizer combinations, however questions that are always asked when hybrids are mentioned for large scale applications are - how do they scale and has it been shown in a large motor? To answer those questions, large scale motor testing is required to verify the hybrid motor at its true size. The necessity to conduct large-scale hybrid rocket motor tests to validate the burn rate from the small motors to application size has been documented in several place^'^^.^. Comparison of small scale hybrid data to that of larger scale data indicates that the fuel burn rate goes down with increasing port size, even with the same oxidizer flux. This trend holds for conventional hybrid motors with forward oxidizer injection and HTPB based fuels. While the reason this is occurring would make a great paper or study or thesis, it is not thoroughly understood at this time. Potential causes include the fact that since hybrid combustion is boundary layer driven, the larger port sizes reduce the interaction (radiation, mixing and heat transfer) from the core region of the port. This chapter focuses on some of the large, prototype sized testing of hybrid motors. The largest motors tested have been AMROC s 250K-lbf thrust motor at Edwards Air Force Base and the Hybrid Propulsion Demonstration Program s 250K-lbf thrust motor at Stennis Space Center. Numerous smaller tests were performed to support the burn rate, stability and scaling concepts that went into the development of those large motors.

10 CFR 431.96 - Uniform test method for the measurement of energy efficiency of small, large, and very large...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., packaged terminal air conditioners, and packaged terminal heat pumps. 431.96 Section 431.96 Energy... EQUIPMENT Commercial Air Conditioners and Heat Pumps Test Procedures § 431.96 Uniform test method for the... heating equipment, packaged terminal air conditioners, and packaged terminal heat pumps. (a) Scope. This...

10 CFR 431.96 - Uniform test method for the measurement of energy efficiency of small, large, and very large...

Code of Federal Regulations, 2012 CFR

2012-01-01

..., packaged terminal air conditioners, and packaged terminal heat pumps. 431.96 Section 431.96 Energy... EQUIPMENT Commercial Air Conditioners and Heat Pumps Test Procedures § 431.96 Uniform test method for the... heating equipment, packaged terminal air conditioners, and packaged terminal heat pumps. (a) Scope. This...

Rayleigh Scattering for Measuring Flow in a Nozzle Testing Facility

NASA Technical Reports Server (NTRS)

Gomez, Carlos R.; Panda, Jayanta

2006-01-01

A molecular Rayleigh-scattering-based air-density measurement system was built in a large nozzle-and-engine-component test facility for surveying supersonic plumes from jet-engine exhaust. A molecular Rayleigh-scattering-based air-density measurement system was built in a large nozzle-and-enginecomponent test facility for surveying supersonic plumes from jet-engine exhaust

An Approach to Scoring and Equating Tests with Binary Items: Piloting With Large-Scale Assessments

ERIC Educational Resources Information Center

Dimitrov, Dimiter M.

2016-01-01

This article describes an approach to test scoring, referred to as "delta scoring" (D-scoring), for tests with dichotomously scored items. The D-scoring uses information from item response theory (IRT) calibration to facilitate computations and interpretations in the context of large-scale assessments. The D-score is computed from the…

Mononucleosis spot test

MedlinePlus

Monospot test; Heterophile antibody test; Heterophile agglutination test; Paul-Bunnell test; Forssman antibody test ... The mononucleosis spot test is done when symptoms of mononucleosis are ... Fatigue Fever Large spleen (possibly) Sore throat Tender ...

A Combined Ethical and Scientific Analysis of Large-scale Tests of Solar Climate Engineering

NASA Astrophysics Data System (ADS)

Ackerman, T. P.

2017-12-01

Our research group recently published an analysis of the combined ethical and scientific issues surrounding large-scale testing of stratospheric aerosol injection (SAI; Lenferna et al., 2017, Earth's Future). We are expanding this study in two directions. The first is extending this same analysis to other geoengineering techniques, particularly marine cloud brightening (MCB). MCB has substantial differences to SAI in this context because MCB can be tested over significantly smaller areas of the planet and, following injection, has a much shorter lifetime of weeks as opposed to years for SAI. We examine issues such as the role of intent, the lesser of two evils, and the nature of consent. In addition, several groups are currently considering climate engineering governance tools such as a code of ethics and a registry. We examine how these tools might influence climate engineering research programs and, specifically, large-scale testing. The second direction of expansion is asking whether ethical and scientific issues associated with large-scale testing are so significant that they effectively preclude moving ahead with climate engineering research and testing. Some previous authors have suggested that no research should take place until these issues are resolved. We think this position is too draconian and consider a more nuanced version of this argument. We note, however, that there are serious questions regarding the ability of the scientific research community to move to the point of carrying out large-scale tests.

Large-Scale Operations Management Test of Use of the White Amur for Control of Problem Aquatic Plants. Report 2. First Year Poststocking Results. Volume VII. A Model for Evaluation of the Response of the Lake Conway, Florida, Ecosystem to Introduction of the White Amur.

DTIC Science & Technology

1981-11-01

OPERATIONS MANAGEMENT S. TYPE OF REPORT A PERIOD COVERED TEST OF THE USE OF THE WHITE AMUR FOR CONTROL OF Report 2 of a series PROBLEM AQUATIC PLANTS...111. 1981. "Large-Scale Operations Management Test of the Use of the White Amur for Control of Problem Aquatic Plants; Report 2, First Year Poststock...Al 3 LARGE-SCALE OPERATIONS MANAGEMENT TEST OF USE OF THE WHITE AMUR FOR CONTROL OF PROBLEM AQUATIC PLANTS A MODEL FOR EVALUATION OF

Pyrotechnic hazards classification and evaluation program. Run-up reaction testing in pyrotechnic dust suspensions

NASA Technical Reports Server (NTRS)

1971-01-01

A preliminary investigation of the parameters included in run-up dust reactions is presented. Two types of tests were conducted: (1) ignition criteria of large bulk pyrotechnic dusts, and (2) optimal run-up conditions of large bulk pyrotechnic dusts. These tests were used to evaluate the order of magnitude and gross scale requirements needed to induce run-up reactions in pyrotechnic dusts and to simulate at reduced scale an accident that occurred in a manufacturing installation. Test results showed that propagation of pyrotechnic dust clouds resulted in a fireball of relatively long duration and large size. In addition, a plane wave front was observed to travel down the length of the gallery.

Five different tests of reaction time evaluated in HIV seropositive men.

PubMed

Dunlop, O; Bjørklund, R A; Abdelnoor, M; Myrvang, B

1992-09-01

In an attempt to develop a short neuropsychological test battery five different tests of reaction time were assessed according to their ability to discriminate between HIV seropositive men and healthy controls. In all tests a patient group with clinical symptoms was slower than the control group. In the complex reaction time test, which has a large cognitive aspect, even a clinically "asymptomatic" group was slower than the control group. The movement test, a new test with a large motor component, identified most slow responders, defining approximately half of the patients with clinical symptoms and one third of the "asymptomatic" patients as such. A test battery consisting of three tests is suggested for serial assessment and screening.

STEP flight experiments Large Deployable Reflector (LDR) telescope

NASA Technical Reports Server (NTRS)

Runge, F. C.

1984-01-01

Flight testing plans for a large deployable infrared reflector telescope to be tested on a space platform are discussed. Subsystem parts, subassemblies, and whole assemblies are discussed. Assurance of operational deployability, rigidization, alignment, and serviceability will be sought.

Robotic Laser Coating Removal System

DTIC Science & Technology

2008-07-01

Materiel Command IRR Internal Rate of Return JTP Joint Test Protocol JTR Joint Test Report LARPS Large Area Robotic Paint Stripping LASER Light...use of laser paint stripping systems is applicable to depainting activities on large off-aircraft components and weapons systems for the Air Force...The use of laser paint stripping systems is applicable to depainting activities on large off-aircraft components and weapons systems for the Air

Some new tests at the Gottingen laboratory

NASA Technical Reports Server (NTRS)

1921-01-01

The tests at the Gottingen laboratory included: friction tests on a surface treated with omelette, verification tests on the M.V.A. 356 wing, and comparative tests of wing no. 36 at the Eiffel laboratory. The examination of all these experiments leads to the belief that, at large incidences, the speeds registered by the suction manometer of the testing chamber of the Eiffel laboratory wind tunnel are, owing to pressure drop, greater than the actual speeds. Therefore, the values of k(sub x) and k(sub y) measured at the Eiffel laboratory at large incidences are too low.

Applying Multidimensional Item Response Theory Models in Validating Test Dimensionality: An Example of K-12 Large-Scale Science Assessment

ERIC Educational Resources Information Center

Li, Ying; Jiao, Hong; Lissitz, Robert W.

2012-01-01

This study investigated the application of multidimensional item response theory (IRT) models to validate test structure and dimensionality. Multiple content areas or domains within a single subject often exist in large-scale achievement tests. Such areas or domains may cause multidimensionality or local item dependence, which both violate the…

The Washback Effect of Konkoor on Teachers' Attitudes toward Their Teaching

ERIC Educational Resources Information Center

Birjandi, Parviz; Shirkhani, Servat

2012-01-01

Large scale tests have been considered by many scholars in the field of language testing and teaching to influence teaching and learning considerably. The present study looks at the effect of a large scale test (Konkoor) on the attitudes of teachers in high schools. Konkoor is the university entrance examination in Iran which is taken by at least…

Large-Scale Academic Achievement Testing of Deaf and Hard-of-Hearing Students: Past, Present, and Future

ERIC Educational Resources Information Center

Qi, Sen; Mitchell, Ross E.

2012-01-01

The first large-scale, nationwide academic achievement testing program using Stanford Achievement Test (Stanford) for deaf and hard-of-hearing children in the United States started in 1969. Over the past three decades, the Stanford has served as a benchmark in the field of deaf education for assessing student academic achievement. However, the…

Grindability measurements on low-rank fuels. [Prediction of large pulverizer performance from small scale test equipment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peipho, R.R.; Dougan, D.R.

1981-01-01

Experience has shown that the grinding characteristics of low rank coals are best determined by testing them in a pulverizer. Test results from a small MPS-32 Babcock and Wilcox pulverizer to predict large, full-scale pulverizer performance are presented. The MPS-32 apparatus, test procedure and evaluation of test results is described. The test data show that the Hardgrove apparatus and the ASTM test method must be used with great caution when considering low-rank fuels. The MPS-32 meets the needs for real-machine simulation but with some disadvantages. A smaller pulverizer is desirable. 1 ref.

Cryocooler based test setup for high current applications

NASA Astrophysics Data System (ADS)

Pradhan, Jedidiah; Das, Nisith Kr.; Roy, Anindya; Duttagupta, Anjan

2018-04-01

A cryo-cooler based cryogenic test setup has been designed, fabricated, and tested. The setup incorporates two numbers of cryo-coolers, one for sample cooling and the other one for cooling the large magnet coil. The performance and versatility of the setup has been tested using large samples of high-temperature superconductor magnet coil as well as short samples with high current. Several un-calibrated temperature sensors have been calibrated using this system. This paper presents the details of the system along with results of different performance tests.

Estimating free-body modal parameters from tests of a constrained structure

NASA Technical Reports Server (NTRS)

Cooley, Victor M.

1993-01-01

Hardware advances in suspension technology for ground tests of large space structures provide near on-orbit boundary conditions for modal testing. Further advances in determining free-body modal properties of constrained large space structures have been made, on the analysis side, by using time domain parameter estimation and perturbing the stiffness of the constraints over multiple sub-tests. In this manner, passive suspension constraint forces, which are fully correlated and therefore not usable for spectral averaging techniques, are made effectively uncorrelated. The technique is demonstrated with simulated test data.

Testing large aspheric surfaces with complementary annular subaperture interferometric method

NASA Astrophysics Data System (ADS)

Hou, Xi; Wu, Fan; Lei, Baiping; Fan, Bin; Chen, Qiang

2008-07-01

Annular subaperture interferometric method has provided an alternative solution to testing rotationally symmetric aspheric surfaces with low cost and flexibility. However, some new challenges, particularly in the motion and algorithm components, appear when applied to large aspheric surfaces with large departure in the practical engineering. Based on our previously reported annular subaperture reconstruction algorithm with Zernike annular polynomials and matrix method, and the experimental results for an approximate 130-mm diameter and f/2 parabolic mirror, an experimental investigation by testing an approximate 302-mm diameter and f/1.7 parabolic mirror with the complementary annular subaperture interferometric method is presented. We have focused on full-aperture reconstruction accuracy, and discuss some error effects and limitations of testing larger aspheric surfaces with the annular subaperture method. Some considerations about testing sector segment with complementary sector subapertures are provided.

Application-level regression testing framework using Jenkins

DOE PAGES

Budiardja, Reuben; Bouvet, Timothy; Arnold, Galen

2017-09-26

Monitoring and testing for regression of large-scale systems such as the NCSA's Blue Waters supercomputer are challenging tasks. In this paper, we describe the solution we came up with to perform those tasks. The goal was to find an automated solution for running user-level regression tests to evaluate system usability and performance. Jenkins, an automation server software, was chosen for its versatility, large user base, and multitude of plugins including collecting data and plotting test results over time. We also describe our Jenkins deployment to launch and monitor jobs on remote HPC system, perform authentication with one-time password, and integratemore » with our LDAP server for its authorization. We show some use cases and describe our best practices for successfully using Jenkins as a user-level system-wide regression testing and monitoring framework for large supercomputer systems.« less

Application-level regression testing framework using Jenkins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Budiardja, Reuben; Bouvet, Timothy; Arnold, Galen

Monitoring and testing for regression of large-scale systems such as the NCSA's Blue Waters supercomputer are challenging tasks. In this paper, we describe the solution we came up with to perform those tasks. The goal was to find an automated solution for running user-level regression tests to evaluate system usability and performance. Jenkins, an automation server software, was chosen for its versatility, large user base, and multitude of plugins including collecting data and plotting test results over time. We also describe our Jenkins deployment to launch and monitor jobs on remote HPC system, perform authentication with one-time password, and integratemore » with our LDAP server for its authorization. We show some use cases and describe our best practices for successfully using Jenkins as a user-level system-wide regression testing and monitoring framework for large supercomputer systems.« less

Experimental determination of optimum gutter brush parameters and road sweeping criteria for different types of waste.

PubMed

Abdel-Wahab, Magd M; Wang, Chong; Vanegas-Useche, Libardo V; Parker, Graham A

2011-06-01

The removal ability of gutter brushes for road sweeping for various debris types and different sweeping parameters is studied through experimental tests. The brushing test rig used comprises two commercial gutter brushes, a concrete test bed, and an asphalt test road with a gutter of 0.25 cm width and 10° slope. The brush-surface contact area is determined by sweeping sand on the concrete test bed. Sweeping problems are identified and discussed, and sweeping criteria for the different debris types are suggested. Also, optimum sweeping parameters are proposed for each debris type. In addition, debris removal mechanisms are discussed and analysed. The results indicate that for large heavy debris such as stones and gravel, it is not difficult to achieve large removal forces, because the steel bristles are relatively stiff. Conversely, high removal forces are not needed for particles of millimetre or micron sizes, but bristle curvature has to be appropriate to remove particles from road concavities. Finally, it is found that mud, especially dry mud on a rough surface, is the hardest debris to sweep, requiring a brush with a large tilt angle and a very large penetration to produce large removal forces. Copyright © 2011 Elsevier Ltd. All rights reserved.

Cost-Efficient Storage of Cryogens

NASA Technical Reports Server (NTRS)

Fesmire, J. E.; Sass, J. P.; Nagy, Z.; Sojoumer, S. J.; Morris, D. L.; Augustynowicz, S. D.

2007-01-01

NASA's cryogenic infrastructure that supports launch vehicle operations and propulsion testing is reaching an age where major refurbishment will soon be required. Key elements of this infrastructure are the large double-walled cryogenic storage tanks used for both space vehicle launch operations and rocket propulsion testing at the various NASA field centers. Perlite powder has historically been the insulation material of choice for these large storage tank applications. New bulk-fill insulation materials, including glass bubbles and aerogel beads, have been shown to provide improved thermal and mechanical performance. A research testing program was conducted to investigate the thermal performance benefits as well as to identify operational considerations and associated risks associated with the application of these new materials in large cryogenic storage tanks. The program was divided into three main areas: material testing (thermal conductivity and physical characterization), tank demonstration testing (liquid nitrogen and liquid hydrogen), and system studies (thermal modeling, economic analysis, and insulation changeout). The results of this research work show that more energy-efficient insulation solutions are possible for large-scale cryogenic storage tanks worldwide and summarize the operational requirements that should be considered for these applications.

Formability analysis of sheet metals by cruciform testing

NASA Astrophysics Data System (ADS)

Güler, B.; Alkan, K.; Efe, M.

2017-09-01

Cruciform biaxial tests are increasingly becoming popular for testing the formability of sheet metals as they achieve frictionless, in-plane, multi-axial stress states with a single sample geometry. However, premature fracture of the samples during testing prevents large strain deformation necessary for the formability analysis. In this work, we introduce a miniature cruciform sample design (few mm test region) and a test setup to achieve centre fracture and large uniform strains. With its excellent surface finish and optimized geometry, the sample deforms with diagonal strain bands intersecting at the test region. These bands prevent local necking and concentrate the strains at the sample centre. Imaging and strain analysis during testing confirm the uniform strain distributions and the centre fracture are possible for various strain paths ranging from plane-strain to equibiaxial tension. Moreover, the sample deforms without deviating from the predetermined strain ratio at all test conditions, allowing formability analysis under large strains. We demonstrate these features of the cruciform test for three sample materials: Aluminium 6061-T6 alloy, DC-04 steel and Magnesium AZ31 alloy, and investigate their formability at both the millimetre scale and the microstructure scale.

The effect of peer-group size on the delivery of feedback in basic life support refresher training: a cluster randomized controlled trial.

PubMed

Cho, Youngsuk; Je, Sangmo; Yoon, Yoo Sang; Roh, Hye Rin; Chang, Chulho; Kang, Hyunggoo; Lim, Taeho

2016-07-04

Students are largely providing feedback to one another when instructor facilitates peer feedback rather than teaching in group training. The number of students in a group affect the learning of students in the group training. We aimed to investigate whether a larger group size increases students' test scores on a post-training test with peer feedback facilitated by instructor after video-guided basic life support (BLS) refresher training. Students' one-rescuer adult BLS skills were assessed by a 2-min checklist-based test 1 year after the initial training. A cluster randomized controlled trial was conducted to evaluate the effect of student number in a group on BLS refresher training. Participants included 115 final-year medical students undergoing their emergency medicine clerkship. The median number of students was 8 in the large groups and 4 in the standard group. The primary outcome was to examine group differences in post-training test scores after video-guided BLS training. Secondary outcomes included the feedback time, number of feedback topics, and results of end-of-training evaluation questionnaires. Scores on the post-training test increased over three consecutive tests with instructor-led peer feedback, but not differ between large and standard groups. The feedback time was longer and number of feedback topics generated by students were higher in standard groups compared to large groups on the first and second tests. The end-of-training questionnaire revealed that the students in large groups preferred the smaller group size compared to their actual group size. In this BLS refresher training, the instructor-led group feedback increased the test score after tutorial video-guided BLS learning, irrespective of the group size. A smaller group size allowed more participations in peer feedback.

Solution for testing large high-power laser lenses having long focal length (Conference Presentation)

NASA Astrophysics Data System (ADS)

Fappani, Denis; IDE, Monique

2017-05-01

Many high power laser facilities are in operation all around the world and include various tight optical components such as large focussing lenses. Such lenses exhibit generally long focal lengths which induces some issues for their optical testing during manufacturing and inspection. Indeed, their transmitted wave fronts need to be very accurate and interferometric testing is the baseline to achieve that. But, it is always a problem to manage simultaneously long testing distances and fine accuracies in such interferometry testing. Taking example of the large focusing lenses produced for the Orion experimentation at AWE (UK), the presentation will describe which kind of testing method has been developed to demonstrate simultaneously good performances with sufficiently good repeatability and absolute accuracy. Special emphasis will be made onto the optical manufacturing issues and interferometric testing solutions. Some ZEMAX results presenting the test set-up and the calibration method will be presented as well. The presentation will conclude with a brief overview of the existing "state of the art" at Thales SESO for these technologies.

An Exploratory Analysis of Economic Factors in the Navy Total Force Strength Model (NTFSM)

DTIC Science & Technology

2015-12-01

NTFSM is still in the testing phase and its overall behavior is largely unknown. In particular, the analysts that NTFSM was designed to help are...NTFSM is still in the testing phase and its overall behavior is largely unknown. In particular, the analysts that NTFSM was designed to help are...7 B. NTFSM VERIFICATION AND TESTING ......................................... 8 C

Recent Developments in Language Assessment and the Case of Four Large-Scale Tests of ESOL Ability

ERIC Educational Resources Information Center

Stoynoff, Stephen

2009-01-01

This review article surveys recent developments and validation activities related to four large-scale tests of L2 English ability: the iBT TOEFL, the IELTS, the FCE, and the TOEIC. In addition to describing recent changes to these tests, the paper reports on validation activities that were conducted on the measures. The results of this research…

Silent and Vocal Students in a Large Active Learning Chemistry Classroom: Comparison of Performance and Motivational Factors

ERIC Educational Resources Information Center

Obenland, Carrie A.; Munson, Ashlyn H.; Hutchinson, John S.

2013-01-01

Active learning is becoming more prevalent in large science classrooms, and this study shows the impact on performance of being vocal during Socratic questioning in a General Chemistry course. 800 college students over a two year period were given a pre and post-test using the Chemistry Concept Reasoning Test. The pre-test results showed that…

An NCME Instructional Module on Booklet Designs in Large-Scale Assessments of Student Achievement: Theory and Practice

ERIC Educational Resources Information Center

Frey, Andreas; Hartig, Johannes; Rupp, Andre A.

2009-01-01

In most large-scale assessments of student achievement, several broad content domains are tested. Because more items are needed to cover the content domains than can be presented in the limited testing time to each individual student, multiple test forms or booklets are utilized to distribute the items to the students. The construction of an…

WWC Review of the Report "Daily Online Testing in Large Classes: Boosting College Performance While Reducing Achievement Gaps." What Works Clearinghouse Single Study Review

ERIC Educational Resources Information Center

What Works Clearinghouse, 2014

2014-01-01

The 2013 study, "Daily Online Testing in Large Classes: Boosting College Performance While Reducing Achievement Gaps," examined the impact of frequent online testing and immediate feedback on the academic performance of college students. The study was conducted at the University of Texas in the fall of 2008 and 2011. Researchers found…

Redesign and Test of an SSME Turbopump for the Large Throat Main Combustion Chamber

NASA Technical Reports Server (NTRS)

Lunde, K. J.; Lee, G. A.; Eastland, A. H.; Rojas, L.

1994-01-01

The preburner oxidizer turbopump for the Space Shuttle Main Engine (SSME) was successfully redesigned for use with the Large Throat Main Combustion Chamber (LTMCC) and tested in air utilizing rapid prototyping. The redesign increases the SSME's operating range with the current Main Combustion Chamber (MCC) while achieving full operational range with the LTMCC. The use of rapid prototyping and air testing to validate the redesign demonstrated the ability to design, fabricate and test designs rapidly and at a very low cost.

Testing large flats with computer generated holograms

NASA Astrophysics Data System (ADS)

Pariani, Giorgio; Tresoldi, Daniela; Spanò, Paolo; Bianco, Andrea

2012-09-01

We describe the optical test of a large flat based on a spherical mirror and a dedicated CGH. The spherical mirror, which can be accurately manufactured and tested in absolute way, allows to obtain a quasi collimated light beam, and the hologram performs the residual wavefront correction. Alignment tools for the spherical mirror and the hologram itself are encoded in the CGH. Sensitivity to fabrication errors and alignment has been evaluated. Tests to verify the effectiveness of our approach are now under execution.

Construction, testing and development of large wind energy facilities

NASA Technical Reports Server (NTRS)

Windheim, R. (Editor); Cuntze, R. (Editor)

1982-01-01

Building large rotor blades and control of oscillations in large facilities are discussed. It is concluded that the technical problems in the design of large rotor blades and control of oscillations can be solved.

Expert Systems In Medical Studies - A New Twist

NASA Astrophysics Data System (ADS)

Slagle, James R.; Long, John M.; Wick, Michael R.; Matts, John P.; Leon, Arthur S.

1986-03-01

The use of experts to evaluate large amounts of trial data results in increasingly expensive and time consuming research. We are investigating the role expert systems can play in reducing the time and expense of research projects. Current methods in large clinical studies for evaluating data are often crude and superficial. We have developed, for a large clinical trial, an expert system for analysis of treadmill exercise ECG test results. In the cases we are studying, a patient is given a treadmill exercise ECG test once a year for five years. Pairs of these exercise tests are then evaluated by cardiologists to determine the condition of the patient's heart. The results of our system show great promise for the use of expert systems in reducing the time and expense of large clinical trials.

Development and Initial Testing of the Tiltrotor Test Rig

NASA Technical Reports Server (NTRS)

Acree, C. W., Jr.; Sheikman, A. L.

2018-01-01

The NASA Tiltrotor Test Rig (TTR) is a new, large-scale proprotor test system, developed jointly with the U.S. Army and Air Force, to develop a new, large-scale proprotor test system for the National Full-Scale Aerodynamics Complex (NFAC). The TTR is designed to test advanced proprotors up to 26 feet in diameter at speeds up to 300 knots, and even larger rotors at lower airspeeds. This combination of size and speed is unprecedented and is necessary for research into 21st-century tiltrotors and other advanced rotorcraft concepts. The TTR will provide critical data for validation of state-of-the-art design and analysis tools.

Development of fire test methods for airplane interior materials

NASA Technical Reports Server (NTRS)

Tustin, E. A.

1978-01-01

Fire tests were conducted in a 737 airplane fuselage at NASA-JSC to characterize jet fuel fires in open steel pans (simulating post-crash fire sources and a ruptured airplane fuselage) and to characterize fires in some common combustibles (simulating in-flight fire sources). Design post-crash and in-flight fire source selections were based on these data. Large panels of airplane interior materials were exposed to closely-controlled large scale heating simulations of the two design fire sources in a Boeing fire test facility utilizing a surplused 707 fuselage section. Small samples of the same airplane materials were tested by several laboratory fire test methods. Large scale and laboratory scale data were examined for correlative factors. Published data for dangerous hazard levels in a fire environment were used as the basis for developing a method to select the most desirable material where trade-offs in heat, smoke and gaseous toxicant evolution must be considered.

Fracture Tests of Etched Components Using a Focused Ion Beam Machine

NASA Technical Reports Server (NTRS)

Kuhn, Jonathan, L.; Fettig, Rainer K.; Moseley, S. Harvey; Kutyrev, Alexander S.; Orloff, Jon; Powers, Edward I. (Technical Monitor)

2000-01-01

Many optical MEMS device designs involve large arrays of thin (0.5 to 1 micron components subjected to high stresses due to cyclic loading. These devices are fabricated from a variety of materials, and the properties strongly depend on size and processing. Our objective is to develop standard and convenient test methods that can be used to measure the properties of large numbers of witness samples, for every device we build. In this work we explore a variety of fracture test configurations for 0.5 micron thick silicon nitride membranes machined using the Reactive Ion Etching (RIE) process. Testing was completed using an FEI 620 dual focused ion beam milling machine. Static loads were applied using a probe. and dynamic loads were applied through a piezo-electric stack mounted at the base of the probe. Results from the tests are presented and compared, and application for predicting fracture probability of large arrays of devices are considered.

Large format array controller (aLFA-C): tests and characterisation at ESA

NASA Astrophysics Data System (ADS)

Lemmel, Frédéric; ter Haar, Jörg; van der Biezen, John; Duvet, Ludovic; Nelms, Nick; Blommaert, Sander; Butler, Bart; van der Luijt, Cornelis; Heijnen, Jerko; Smit, Hans; Visser, Ivo

2016-08-01

For future near infrared astronomy missions, ESA is developing a complete detection and conversion chain (photon to SpaceWire chain system): Large Format Array (aLFA-N) based on MCT type detectors. aLFA-C (Astronomy Large Format Array Controller): a versatile cryogenic detector controller. An aLFA-C prototype was developed by Caeleste (Belgium) under ESA contract (400106260400). To validate independently the performances of the aLFA-C prototype and consolidate the definition of the follow-on activity, a dedicated test bench has been designed and developed in ESTEC/ESA within the Payload Technology Validation group. This paper presents the test setup and the performance validation of the first prototype of this controller at room and cryogenic temperature. Test setup and software needed to test the HAWAII-2RG and aLFA-N detectors with the aLFA-C prototype at cryogenic temperature will be also presented.

A New Large Vibration Test Facility Concept for the James Webb Space Telescope

NASA Technical Reports Server (NTRS)

Ross, Brian P.; Johnson, Eric L.; Hoksbergen, Joel; Lund, Doug

2014-01-01

The James Webb Space Telescope consists of three main components, the Integrated Science Instrument Module (ISIM) Element, the Optical Telescope Element (OTE), and the Spacecraft Element. The ISIM and OTE are being assembled at the National Aeronautics and Space Administration's Goddard Spaceflight Center (GSFC). The combined OTE and ISIM Elements, called OTIS, will undergo sine vibration testing before leaving Goddard. OTIS is the largest payload ever tested at Goddard and the existing GSFC vibration facilities are incapable of performing a sine vibration test of the OTIS payload. As a result, a new large vibration test facility is being designed. The new facility will consist of a vertical system with a guided head expander and a horizontal system with a hydrostatic slip table. The project is currently in the final design phase with installation to begin in early 2015 and the facility is expected to be operational by late 2015. This paper will describe the unique requirements for a new large vibration test facility and present the selected final design concepts.

Mechanical abuse simulation and thermal runaway risks of large-format Li-ion batteries

NASA Astrophysics Data System (ADS)

Wang, Hsin; Lara-Curzio, Edgar; Rule, Evan T.; Winchester, Clinton S.

2017-02-01

Internal short circuit of large-format Li-ion pouch cells induced by mechanical abuse was simulated using a modified mechanical pinch test. A torsion force was added manually at ∼40% maximum compressive loading force during the pinch test. The cell was twisted about 5° to the side by horizontally pulling a wire attached to the anode tab. The combined torsion-compression force created small failure at the separator yet allowed testing of fully charged large format Li-ion cells without triggering thermal runaway. Two types of commercial cells were tested using 4-6 cells at each state-of-charge (SOC). Commercially available 18 Ahr LiFePO4 (LFP) and 25 Ahr Li(NiMnCo)1/3O2 (NMC) cells were tested, and a thermal runaway risk (TRR) score system was used to evaluate the safety of the cells under the same testing conditions. The aim was to provide the cell manufacturers and end users with a tool to compare different designs and safety features.

Extreme-value statistics reveal rare failure-critical defects in additive manufacturing

DOE PAGES

Boyce, Brad L.; Salzbrenner, Bradley C.; Rodelas, Jeffrey M.; ...

2017-04-21

Additive manufacturing enables the rapid, cost effective production of large populations of material test coupons such as tensile bars. By adopting streamlined test methods including ‘drop-in’ grips and non-contact extensometry, testing these large populations becomes more efficient. Unlike hardness tests, the tensile test provides a direct measure of yield strength, flow properties, and ductility, which can be directly incorporated into solid mechanics simulations. In the present work, over 1000 nominally identical tensile tests were used to explore the effect of process variability on the mechanical property distributions of a precipitation hardened stainless steel, 17-4PH, produced by a laser powder bedmore » fusion process, also known as direct metal laser sintering. With this large dataset, rare defects are revealed that affect only ~2% of the population, stemming from a single build lot of material. Lastly, the rare defects caused a substantial loss in ductility and were associated with an interconnected network of porosity.« less

Large strain cruciform biaxial testing for FLC detection

NASA Astrophysics Data System (ADS)

Güler, Baran; Efe, Mert

2017-10-01

Selection of proper test method, specimen design and analysis method are key issues for studying formability of sheet metals and detection of their forming limit curves (FLC). Materials with complex microstructures may need an additional micro-mechanical investigation and accurate modelling. Cruciform biaxial test stands as an alternative to standard tests as it achieves frictionless, in-plane, multi-axial stress states with a single sample geometry. In this study, we introduce a small-scale (less than 10 cm) cruciform sample allowing micro-mechanical investigation at stress states ranging from plane strain to equibiaxial. With successful specimen design and surface finish, large forming limit strains are obtained at the test region of the sample. The large forming limit strains obtained by experiments are compared to the values obtained from Marciniak-Kuczynski (M-K) local necking model and Cockroft-Latham damage model. This comparison shows that the experimental limiting strains are beyond the theoretical values, approaching to the fracture strain of the two test materials: Al-6061-T6 aluminum alloy and DC-04 high formability steel.

Effects of reinforcement on test-enhanced learning in a large, diverse introductory college psychology course.

PubMed

Trumbo, Michael C; Leiting, Kari A; McDaniel, Mark A; Hodge, Gordon K

2016-06-01

A robust finding within laboratory research is that structuring information as a test confers benefit on long-term retention-referred to as the testing effect. Although well characterized in laboratory environments, the testing effect has been explored infrequently within ecologically valid contexts. We conducted a series of 3 experiments within a very large introductory college-level course. Experiment 1 examined the impact of required versus optional frequent low-stakes testing (quizzes) on student grades, revealing students were much more likely to take advantage of quizzing if it was a required course component. Experiment 2 implemented a method of evaluating pedagogical intervention within a single course (thereby controlling for instructor bias and student self-selection), which revealed a testing effect. Experiment 3 ruled out additional exposure to information as an explanation for the findings of Experiment 2 and suggested that students at the college level, enrolled in very large sections, accept frequent quizzing well. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Large-Scale Low-Boom Inlet Test Overview

NASA Technical Reports Server (NTRS)

Hirt, Stefanie

2011-01-01

This presentation provides a high level overview of the Large-Scale Low-Boom Inlet Test and was presented at the Fundamental Aeronautics 2011 Technical Conference. In October 2010 a low-boom supersonic inlet concept with flow control was tested in the 8'x6' supersonic wind tunnel at NASA Glenn Research Center (GRC). The primary objectives of the test were to evaluate the inlet stability and operability of a large-scale low-boom supersonic inlet concept by acquiring performance and flowfield validation data, as well as evaluate simple, passive, bleedless inlet boundary layer control options. During this effort two models were tested: a dual stream inlet intended to model potential flight hardware and a single stream design to study a zero-degree external cowl angle and to permit surface flow visualization of the vortex generator flow control on the internal centerbody surface. The tests were conducted by a team of researchers from NASA GRC, Gulfstream Aerospace Corporation, University of Illinois at Urbana-Champaign, and the University of Virginia

Large Space Antenna Systems Technology, 1984

NASA Technical Reports Server (NTRS)

Boyer, W. J. (Compiler)

1985-01-01

Mission applications for large space antenna systems; large space antenna structural systems; materials and structures technology; structural dynamics and control technology, electromagnetics technology, large space antenna systems and the Space Station; and flight test and evaluation were examined.

False-Positive Tuberculin Skin Test Results Among Low-Risk Healthcare Workers Following Implementation of Fifty-Dose Vials of Purified Protein Derivative.

PubMed

Collins, Jeffrey M; Hunter, Mary; Gordon, Wanda; Kempker, Russell R; Blumberg, Henry M; Ray, Susan M

2018-06-01

Following large declines in tuberculosis transmission the United States, large-scale screening programs targeting low-risk healthcare workers are increasingly a source of false-positive results. We report a large cluster of presumed false-positive tuberculin skin test results in healthcare workers following a change to 50-dose vials of Tubersol tuberculin.Infect Control Hosp Epidemiol 2018;39:750-752.

Large animal and primate models of spinal cord injury for the testing of novel therapies.

PubMed

Kwon, Brian K; Streijger, Femke; Hill, Caitlin E; Anderson, Aileen J; Bacon, Mark; Beattie, Michael S; Blesch, Armin; Bradbury, Elizabeth J; Brown, Arthur; Bresnahan, Jacqueline C; Case, Casey C; Colburn, Raymond W; David, Samuel; Fawcett, James W; Ferguson, Adam R; Fischer, Itzhak; Floyd, Candace L; Gensel, John C; Houle, John D; Jakeman, Lyn B; Jeffery, Nick D; Jones, Linda Ann Truett; Kleitman, Naomi; Kocsis, Jeffery; Lu, Paul; Magnuson, David S K; Marsala, Martin; Moore, Simon W; Mothe, Andrea J; Oudega, Martin; Plant, Giles W; Rabchevsky, Alexander Sasha; Schwab, Jan M; Silver, Jerry; Steward, Oswald; Xu, Xiao-Ming; Guest, James D; Tetzlaff, Wolfram

2015-07-01

Large animal and primate models of spinal cord injury (SCI) are being increasingly utilized for the testing of novel therapies. While these represent intermediary animal species between rodents and humans and offer the opportunity to pose unique research questions prior to clinical trials, the role that such large animal and primate models should play in the translational pipeline is unclear. In this initiative we engaged members of the SCI research community in a questionnaire and round-table focus group discussion around the use of such models. Forty-one SCI researchers from academia, industry, and granting agencies were asked to complete a questionnaire about their opinion regarding the use of large animal and primate models in the context of testing novel therapeutics. The questions centered around how large animal and primate models of SCI would be best utilized in the spectrum of preclinical testing, and how much testing in rodent models was warranted before employing these models. Further questions were posed at a focus group meeting attended by the respondents. The group generally felt that large animal and primate models of SCI serve a potentially useful role in the translational pipeline for novel therapies, and that the rational use of these models would depend on the type of therapy and specific research question being addressed. While testing within these models should not be mandatory, the detection of beneficial effects using these models lends additional support for translating a therapy to humans. These models provides an opportunity to evaluate and refine surgical procedures prior to use in humans, and safety and bio-distribution in a spinal cord more similar in size and anatomy to that of humans. Our results reveal that while many feel that these models are valuable in the testing of novel therapies, important questions remain unanswered about how they should be used and how data derived from them should be interpreted. Copyright © 2015 Elsevier Inc. All rights reserved.

Potential Damage to Flight Hardware from MIL-STD-462 CS02 Setup

NASA Technical Reports Server (NTRS)

Harris, Patrick K.; Block, Nathan F.

2002-01-01

The MIL-STD-462 CS02 conducted susceptibility test setup, performed during electromagnetic compatibility (EMC) testing, consists of an audio transformer with the secondary used as an inductor and a large capacitor. Together, these two components form an L-type low-pass filter to minimize the injected test signal input into the power source. Some flight hardware power input configurations are not compatible with this setup and break into oscillation when powered up. This can damage flight hardware and caused a catastrophic failure to an item tested in the Goddard Space Flight Center (GSFC) Large EMC Test Facility.

Large-Scale Wind-Tunnel Tests of an Airplane Model with an Unswept, Tilt Wing of Aspect Ratio 5.5, and with Four Propellers and Blowing Flaps

NASA Technical Reports Server (NTRS)

Weiberg, James A.; Holzhauser, Curt A.

1961-01-01

Tests were made of a large-scale tilt-wing deflected-slipstream VTOL airplane with blowing-type BLC trailing-edge flaps. The model was tested with flap deflections of 0 deg. without BLC, 50 deg. with and without BLC, and 80 deg. with BLC for wing-tilt angles of 0, 30, and 50 deg. Included are results of tests of the model equipped with a leading-edge flap and the results of tests of the model in the presence of a ground plane.

Parallel and serial computing tools for testing single-locus and epistatic SNP effects of quantitative traits in genome-wide association studies

PubMed Central

Ma, Li; Runesha, H Birali; Dvorkin, Daniel; Garbe, John R; Da, Yang

2008-01-01

Background Genome-wide association studies (GWAS) using single nucleotide polymorphism (SNP) markers provide opportunities to detect epistatic SNPs associated with quantitative traits and to detect the exact mode of an epistasis effect. Computational difficulty is the main bottleneck for epistasis testing in large scale GWAS. Results The EPISNPmpi and EPISNP computer programs were developed for testing single-locus and epistatic SNP effects on quantitative traits in GWAS, including tests of three single-locus effects for each SNP (SNP genotypic effect, additive and dominance effects) and five epistasis effects for each pair of SNPs (two-locus interaction, additive × additive, additive × dominance, dominance × additive, and dominance × dominance) based on the extended Kempthorne model. EPISNPmpi is the parallel computing program for epistasis testing in large scale GWAS and achieved excellent scalability for large scale analysis and portability for various parallel computing platforms. EPISNP is the serial computing program based on the EPISNPmpi code for epistasis testing in small scale GWAS using commonly available operating systems and computer hardware. Three serial computing utility programs were developed for graphical viewing of test results and epistasis networks, and for estimating CPU time and disk space requirements. Conclusion The EPISNPmpi parallel computing program provides an effective computing tool for epistasis testing in large scale GWAS, and the epiSNP serial computing programs are convenient tools for epistasis analysis in small scale GWAS using commonly available computer hardware. PMID:18644146

Experience with specifications applicable to certification. [of photovoltaic modules for large-scale application

NASA Technical Reports Server (NTRS)

Ross, R. G., Jr.

1982-01-01

The Jet Propulsion Laboratory has developed a number of photovoltaic test and measurement specifications to guide the development of modules toward the requirements of future large-scale applications. Experience with these specifications and the extensive module measurement and testing that has accompanied their use is examined. Conclusions are drawn relative to three aspects of product certification: performance measurement, endurance testing and safety evaluation.

Large optics technology; Proceedings of the Meeting, San Diego, CA, August 19-21, 1985. Volume 571

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanger, G.M.

1986-01-01

The present conference on telescope primary mirror design and manufacturing technologies considers topics in mirror fabrication and testing, novel technology currently under development, recently instituted large optics development programs, and large mirror materials. Among the topics discussed are aspheric figure generation using feedback from an IR phase-shifting interferometer, thermal stability tests of CFRP sandwich panels for far-IR astronomy, Zerodur lightweight (large mirror) blanks, and the precision machining of grazing-incidence X-ray mirror substrates. Also treated are the rapid fabrication of large aspheric optics, steps toward 8-m honeycomb mirrors, a novel telescope design employing the refraction of prism rows, telescope technology formore » the Far-UV Spectroscopic Explorer, hot isostatic-pressed Be for large optics, and a concept for a moderate cost large deployable reflector.« less

VOLUMETRIC LEAK DETECTION IN LARGE UNDERGROUND STORAGE TANKS - VOLUME II: APPENDICES A-E

EPA Science Inventory

The program of experiments conducted at Griffiss Air Force Base was devised to expand the understanding of large underground storage tank behavior as it impacts the performance of volumetric leak detection testing. The report addresses three important questions about testing the ...

An Investigation of a Vertical Test Method for Large Deformation Bending of High Strain Composite Laminates

NASA Astrophysics Data System (ADS)

Herrmann, Kelsey M.

Research to date indicates that traditional composite material failure analysis methods are not appropriate for thin laminates in flexure. Thin composite structures subjected to large bending deformations often attain significantly higher strain-to-failure than previously anticipated tensile and compression coupon test data and linear material model assumption predict. At NASA Langley Research Center, a new bend test method is being developed for High Strain Composite (HSC) structures. This method provides an adequate approximation of a pure moment, large deformation bend test for thin-ply, high strain composites to analyze the large strain flexure response of the laminates. The objective of this research was to further develop this new test method to measure the true bending stiffness and strain-to-failure of high strain composite materials. Of primary importance is the ability to characterize composite laminates that are of interest for current NASA deployable structures in both materials and layups. Two separate testing campaigns were performed for the development of the testing procedure. Initially six laminates were bend tested in three different fiber orientations. These laminates were some combination of unidirectional intermediate modulus (IM) carbon, high tenacity (HT) carbon plain weave, and astroquartz plain weave composite materials. The second test campaign was performed as a more detailed look into the simplest composite laminates at thicknesses that better represented deployable boom structures. The second campaign tested three basic, thinner laminates, again in three different fiber orientations. All testing was monotonic loading to failure. The thickness of the laminates tested ranged from 0.166mm (campaign 2) to 0.45mm (campaign 1). The measured strains at failure for the unidirectional material were approximately 2.1% and 1.4% at the compression and tension sides, respectively, failing as fiber tensile fracture. Both of these values differ from what would be expected from considering much thicker coupons tested under pure compression and tension, that show a strain-to-failure of 1.0-1.1% and 1.6-1.7%, respectively. The significant differences in strain values obtained at the outer surfaces of the coupon is thought to be related to the shift in neutral axis that the specimen experiences during the large deformation bending test as a result of fiber material nonlinearities at higher strains. The vertical test nature of the CBT when compared to other test methods proves to be helpful for visually capturing with Digital Image Correlation the distinct behavior of the flexure on both the compressive and tensile sides. It was found that the thinner the laminate tested, the more confirmation of a nonlinear response of this classification of composites. The moment versus curvature curves were predominantly nonlinear resulting in a near linear bending stiffness versus curvature response. At these large strains, carbon fibers are highly nonlinear resulting in the laminate flexure modulus increasing by up to 5x. The theoretical bending stiffness values calculated using Classical Lamination Theory analysis are within small differences with respect to the experimentally measured values: errors of approximately 5-10% for both D11 and D22. The error between the finite element model computed strain response and the experimental values was on average around 22%, with 35% of the laminates and orientation having errors less than 7%. Comparison between CLT, FEA, and experimentation show that the Column Bend Test appears to be a promising candidate for characterization of large deformation bending behavior of thin-ply high strain composite laminates.

Reference Material Kydex(registered trademark)-100 Test Data Message for Flammability Testing

NASA Technical Reports Server (NTRS)

Engel, Carl D.; Richardson, Erin; Davis, Eddie

2003-01-01

The Marshall Space Flight Center (MSFC) Materials and Processes Technical Information System (MAPTIS) database contains, as an engineering resource, a large amount of material test data carefully obtained and recorded over a number of years. Flammability test data obtained using Test 1 of NASA-STD-6001 is a significant component of this database. NASA-STD-6001 recommends that Kydex 100 be used as a reference material for testing certification and for comparison between test facilities in the round-robin certification testing that occurs every 2 years. As a result of these regular activities, a large volume of test data is recorded within the MAPTIS database. The activity described in this technical report was undertaken to mine the database, recover flammability (Test 1) Kydex 100 data, and review the lessons learned from analysis of these data.

Procedures for experimental measurement and theoretical analysis of large plastic deformations

NASA Technical Reports Server (NTRS)

Morris, R. E.

1974-01-01

Theoretical equations are derived and analytical procedures are presented for the interpretation of experimental measurements of large plastic strains in the surface of a plate. Orthogonal gage lengths established on the metal surface are measured before and after deformation. The change in orthogonality after deformation is also measured. Equations yield the principal strains, deviatoric stresses in the absence of surface friction forces, true stresses if the stress normal to the surface is known, and the orientation angle between the deformed gage line and the principal stress-strain axes. Errors in the measurement of nominal strains greater than 3 percent are within engineering accuracy. Applications suggested for this strain measurement system include the large-strain-stress analysis of impact test models, burst tests of spherical or cylindrical pressure vessels, and to augment small-strain instrumentation tests where large strains are anticipated.

Study on Thermal Decomposition Characteristics of Ammonium Nitrate Emulsion Explosive in Different Scales

NASA Astrophysics Data System (ADS)

Wu, Qiujie; Tan, Liu; Xu, Sen; Liu, Dabin; Min, Li

2018-04-01

Numerous accidents of emulsion explosive (EE) are attributed to uncontrolled thermal decomposition of ammonium nitrate emulsion (ANE, the intermediate of EE) and EE in large scale. In order to study the thermal decomposition characteristics of ANE and EE in different scales, a large-scale test of modified vented pipe test (MVPT), and two laboratory-scale tests of differential scanning calorimeter (DSC) and accelerating rate calorimeter (ARC) were applied in the present study. The scale effect and water effect both play an important role in the thermal stability of ANE and EE. The measured decomposition temperatures of ANE and EE in MVPT are 146°C and 144°C, respectively, much lower than those in DSC and ARC. As the size of the same sample in DSC, ARC, and MVPT successively increases, the onset temperatures decrease. In the same test, the measured onset temperature value of ANE is higher than that of EE. The water composition of the sample stabilizes the sample. The large-scale test of MVPT can provide information for the real-life operations. The large-scale operations have more risks, and continuous overheating should be avoided.

The use of impact force as a scale parameter for the impact response of composite laminates

NASA Technical Reports Server (NTRS)

Jackson, Wade C.; Poe, C. C., Jr.

1992-01-01

The building block approach is currently used to design composite structures. With this approach, the data from coupon tests is scaled up to determine the design of a structure. Current standard impact tests and methods of relating test data to other structures are not generally understood and are often used improperly. A methodology is outlined for using impact force as a scale parameter for delamination damage for impacts of simple plates. Dynamic analyses were used to define ranges of plate parameters and impact parameters where quasi-static analyses are valid. These ranges include most low velocity impacts where the mass of the impacter is large and the size of the specimen is small. For large mass impacts of moderately thick (0.35 to 0.70 cm) laminates, the maximum extent of delamination damage increased with increasing impact force and decreasing specimen thickness. For large mass impact tests at a given kinetic energy, impact force and hence delamination size depends on specimen size, specimen thickness, boundary conditions, and indenter size and shape. If damage is reported in terms of impact force instead of kinetic energy, large mass test results can be applied directly to other plates of the same size.

The use of impact force as a scale parameter for the impact response of composite laminates

NASA Technical Reports Server (NTRS)

Jackson, Wade C.; Poe, C. C., Jr.

1992-01-01

The building block approach is currently used to design composite structures. With this approach, the data from coupon tests are scaled up to determine the design of a structure. Current standard impact tests and methods of relating test data to other structures are not generally understood and are often used improperly. A methodology is outlined for using impact force as a scale parameter for delamination damage for impacts of simple plates. Dynamic analyses were used to define ranges of plate parameters and impact parameters where quasi-static analyses are valid. These ranges include most low-velocity impacts where the mass of the impacter is large, and the size of the specimen is small. For large-mass impacts of moderately thick (0.35-0.70 cm) laminates, the maximum extent of delamination damage increased with increasing impact force and decreasing specimen thickness. For large-mass impact tests at a given kinetic energy, impact force and hence delamination size depends on specimen size, specimen thickness, boundary conditions, and indenter size and shape. If damage is reported in terms of impact force instead of kinetic energy, large-mass test results can be applied directly to other plates of the same thickness.

Illusory expectations can affect retrieval-monitoring accuracy.

PubMed

McDonough, Ian M; Gallo, David A

2012-03-01

The present study investigated how expectations, even when illusory, can affect the accuracy of memory decisions. Participants studied words presented in large or small font for subsequent memory tests. Replicating prior work, judgments of learning indicated that participants expected to remember large words better than small words, even though memory for these words was equivalent on a standard test of recognition memory and subjective judgments. Critically, we also included tests that instructed participants to selectively search memory for either large or small words, thereby allowing different memorial expectations to contribute to performance. On these tests we found reduced false recognition when searching memory for large words relative to small words, such that the size illusion paradoxically affected accuracy measures (d' scores) in the absence of actual memory differences. Additional evidence for the role of illusory expectations was that (a) the accuracy effect was obtained only when participants searched memory for the aspect of the stimuli corresponding to illusory expectations (size instead of color) and (b) the accuracy effect was eliminated on a forced-choice test that prevented the influence of memorial expectations. These findings demonstrate the critical role of memorial expectations in the retrieval-monitoring process. 2012 APA, all rights reserved

Efficacy of Bordeaux mixture to control pecan scab in large-plot experiments

USDA-ARS?s Scientific Manuscript database

Venturia effusa causes scab, the most important disease on pecan in the southeastern USA. Organic fungicides have not been widely tested for efficacy against scab on susceptible cultivars. A large-plot experiment was used to test the efficacy of the traditionally-used fungicide against scab, Bordeau...

49 CFR 178.970 - Bottom lift test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

49 CFR 178.970 - Bottom lift test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for transportation and no loss of contents. (2) For flexible Large Packagings, there may be no deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (3) For the... of their capacity and to their maximum net mass, with the load being evenly distributed. (c) Test...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... for transportation and no loss of contents. (2) For flexible Large Packagings, there may be no deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (3) For the... of their capacity and to their maximum net mass, with the load being evenly distributed. (c) Test...

49 CFR 178.970 - Bottom lift test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

49 CFR 178.970 - Bottom lift test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

Cryogenic vertical test facility for the SRF cavities at BNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Than, R.; Liaw, CJ; Porqueddu, R.

2011-03-28

A vertical test facility has been constructed to test SRF cavities and can be utilized for other applications. The liquid helium volume for the large vertical dewar is approximate 2.1m tall by 1m diameter with a clearance inner diameter of 0.95m after the inner cold magnetic shield installed. For radiation enclosure, the test dewar is located inside a concrete block structure. The structure is above ground, accessible from the top, and equipped with a retractable concrete roof. A second radiation concrete facility, with ground level access via a labyrinth, is also available for testing smaller cavities in 2 smaller dewars.more » The cryogenic transfer lines installation between the large vertical test dewar and the cryo plant's sub components is currently near completion. Controls and instrumentations wiring are also nearing completion. The Vertical Test Facility will allow onsite testing of SRF cavities with a maximum overall envelope of 0.9 m diameter and 2.1 m height in the large dewar and smaller SRF cavities and assemblies with a maximum overall envelope of 0.66 m diameter and 1.6 m height.« less

Modelling of eddy currents related to large angle magnetic suspension test fixture

NASA Technical Reports Server (NTRS)

Britcher, Colin P.; Foster, Lucas E.

1994-01-01

This report presents a preliminary analysis of the mathematical modelling of eddy current effects in a large-gap magnetic suspension system. It is shown that eddy currents can significantly affect the dynamic behavior and control of these systems, but are amenable to measurement and modelling. A theoretical framework is presented, together with a comparison of computed and experimental data related to the Large Angle Magnetic Suspension Test Fixture at NASA Langley Research Center.

Large space structures testing

NASA Technical Reports Server (NTRS)

Waites, Henry; Worley, H. Eugene

1987-01-01

There is considerable interest in the development of testing concepts and facilities that accurately simulate the pathologies believed to exist in future spacecraft. Both the Government and Industry have participated in the development of facilities over the past several years. The progress and problems associated with the development of the Large Space Structure Test Facility at the Marshall Flight Center are presented. This facility was in existence for a number of years and its utilization has run the gamut from total in-house involvement, third party contractor testing, to the mutual participation of other goverment agencies in joint endeavors.

Software Manages Documentation in a Large Test Facility

NASA Technical Reports Server (NTRS)

Gurneck, Joseph M.

2001-01-01

The 3MCS computer program assists and instrumentation engineer in performing the 3 essential functions of design, documentation, and configuration management of measurement and control systems in a large test facility. Services provided by 3MCS are acceptance of input from multiple engineers and technicians working at multiple locations;standardization of drawings;automated cross-referencing; identification of errors;listing of components and resources; downloading of test settings; and provision of information to customers.

Development, Testing and Operation of a Large Suspended Ocean Measurement Structure for Deep-Ocean Use

DTIC Science & Technology

1992-05-01

and systems for developing , testing, and operating the system. A new, lightweight cable de- used this evolving technology base in the ensuing years...Funding Numbers. Development , Testing, and Operation of a Large Suspended Ocean Contrac Measurement Structure for Deep-Ocean Use Program Element No...Research L.aboratory Report Number. Ocean Acoutics and Technology Directorate PR 91:132:253 Stennis Space Center, MS 39529-5004 9. Sponsoring

Test facilities for high power electric propulsion

NASA Technical Reports Server (NTRS)

Sovey, James S.; Vetrone, Robert H.; Grisnik, Stanley P.; Myers, Roger M.; Parkes, James E.

1991-01-01

Electric propulsion has applications for orbit raising, maneuvering of large space systems, and interplanetary missions. These missions involve propulsion power levels from tenths to tens of megawatts, depending upon the application. General facility requirements for testing high power electric propulsion at the component and thrust systems level are defined. The characteristics and pumping capabilities of many large vacuum chambers in the United States are reviewed and compared with the requirements for high power electric propulsion testing.

Developments in Test Facility and Data Networking for the Altitude Test Stand at the John C. Stennis Space Center: A General Overview

NASA Technical Reports Server (NTRS)

Hebert, Phillip W.

2008-01-01

NASA/SSC's Mission in Rocket Propulsion Testing Is to Acquire Test Performance Data for Verification, Validation and Qualification of Propulsion Systems Hardware: Accurate, Reliable, Comprehensive, and Timely. Data Acquisition in a Rocket Propulsion Test Environment Is Challenging: a) Severe Temporal Transient Dynamic Environments; b) Large Thermal Gradients; c) Vacuum to high pressure regimes. A-3 Test Stand Development is equally challenging with respect to accommodating vacuum environment, operation of a CSG system, and a large quantity of data system and control channels to determine proper engine performance as well as Test Stand operation. SSC is currently in the process of providing modernized DAS, Control Systems, Video, and network systems for the A-3 Test Stand to overcome these challenges.

Fuel containment, lightning protection and damage tolerance in large composite primary aircraft structures

NASA Technical Reports Server (NTRS)

Griffin, Charles F.; James, Arthur M.

1985-01-01

The damage-tolerance characteristics of high strain-to-failure graphite fibers and toughened resins were evaluated. Test results show that conventional fuel tank sealing techniques are applicable to composite structures. Techniques were developed to prevent fuel leaks due to low-energy impact damage. For wing panels subjected to swept stroke lightning strikes, a surface protection of graphite/aluminum wire fabric and a fastener treatment proved effective in eliminating internal sparking and reducing structural damage. The technology features developed were incorporated and demonstrated in a test panel designed to meet the strength, stiffness, and damage tolerance requirements of a large commercial transport aircraft. The panel test results exceeded design requirements for all test conditions. Wing surfaces constructed with composites offer large weight savings if design allowable strains for compression can be increased from current levels.

Substituting Both the N-Terminal and "Cord" Regions of a Xylanase from Aspergillus oryzae to Improve Its Temperature Characteristics.

PubMed

Li, Chuang; Li, Jianfang; Wang, Rui; Li, Xueqing; Li, Jinping; Deng, Chao; Wu, Minchen

2018-02-06

To improve the temperature characteristics of AoXyn11A, a mesophilic glycoside hydrolase family (GHF) 11 xylanase from Aspergillus oryzae CICC40186, its N-terminal and "cord" regions were selected to be substituted by means of the computer-aided analysis and calculation. In brief, one mutant, named ATX11A 41 , possessing the lowest root-mean-square deviation (RMSD) value was designed based on the molecular dynamics (MD) simulation by substituting the N-terminal 41 amino acids of AoXyn11A with the corresponding 42 ones of pXYL11, a thermophilic GHF11 xylanase from Thermobifida fusca. On the basis of the primary structure alignment of pXYL11 with ATX11A 41 (or AoXyn11A), another mutant, named ATX11A 41/cord , was designed by substituting the cord region ( 93 GTYNPGSGG 101 ) of ATX11A 41 with the corresponding one ( 93 GTYRPTG 99 ) of pXYL11. Both mutant-encoding genes, ATx11A 41 and ATx11A 41/cord , were constructed as designed theoretically by a megaprimer PCR technique and were expressed in Pichia pastoris GS115. The specific activities of recombinant (re) AoXyn11A, ATX11A 41 , and ATX11A 41/cord were 2916.7, 2667.6, and 2457.0 U/mg, respectively. The analysis of temperature characteristics displayed that the temperature optimum (T opt ) of reATX11A 41 or reATX11A 41/cord was 65 °C, which was 15 °C higher than that of reAoXyn11A. The thermal inactivation half-life (t 1/2 ) values of reATX11A 41 and reATX11A 41/cord at 60 °C were 55 and 83 min, respectively, whereas that of reAoXyn11A was only 18 min at 50 °C. The melting temperature (T m ) values of reAoXyn11A, reATX11A 41 , and reATX11A 41/cord were 54.2, 66.7, and 71.9 °C, respectively. In conclusion, the above findings indicated that the substitution of both the N-terminal and cord regions of a mesophilic AoXyn11A greatly contributed to its improved temperature characteristics.

When the Test of Mediation is More Powerful than the Test of the Total Effect

PubMed Central

O'Rourke, Holly P.; MacKinnon, David P.

2014-01-01

Although previous research has studied power in mediation models, the extent to which the inclusion of a mediator will increase power has not been investigated. First, a study compared analytical power of the mediated effect to the total effect in a single mediator model to identify the situations in which the inclusion of one mediator increased statistical power. Results from the first study indicated that including a mediator increased statistical power in small samples with large coefficients and in large samples with small coefficients, and when coefficients were non-zero and equal across models. Next, a study identified conditions where power was greater for the test of the total mediated effect compared to the test of the total effect in the parallel two mediator model. Results indicated that including two mediators increased power in small samples with large coefficients and in large samples with small coefficients, the same pattern of results found in the first study. Finally, a study assessed analytical power for a sequential (three-path) two mediator model and compared power to detect the three-path mediated effect to power to detect both the test of the total effect and the test of the mediated effect for the single mediator model. Results indicated that the three-path mediated effect had more power than the mediated effect from the single mediator model and the test of the total effect. Practical implications of these results for researchers are then discussed. PMID:24903690

Variable-Temperature Cryostat For Radiation-Damage Testing Of Germanium Detectors

NASA Technical Reports Server (NTRS)

Floyd, Samuel R.; Puc, Bernard P.

1992-01-01

Variable-temperature cryostats developed to study radiation damage to, and annealing of, germanium gamma-ray detectors. Two styles: one accommodates large single detector and one accommodates two medium-sized detectors. New cryostats allow complete testing of large-volume germanium gamma-ray detectors without breaking cryostat vacuum and removing detectors for annealing.

Modeling Booklet Effects for Nonequivalent Group Designs in Large-Scale Assessment

ERIC Educational Resources Information Center

Hecht, Martin; Weirich, Sebastian; Siegle, Thilo; Frey, Andreas

2015-01-01

Multiple matrix designs are commonly used in large-scale assessments to distribute test items to students. These designs comprise several booklets, each containing a subset of the complete item pool. Besides reducing the test burden of individual students, using various booklets allows aligning the difficulty of the presented items to the assumed…

The Theory about CD-CAT Based on FCA and Its Application

ERIC Educational Resources Information Center

Shuqun, Yang; Shuliang, Ding; Zhiqiang, Yao

2009-01-01

Cognitive diagnosis (CD) plays an important role in intelligent tutoring system. Computerized adaptive testing (CAT) is adaptive, fair, and efficient, which is suitable to large-scale examination. Traditional cognitive diagnostic test needs quite large number of items, the efficient and tailored CAT could be a remedy for it, so the CAT with…

Efficient computation of significance levels for multiple associations in large studies of correlated data, including genomewide association studies.

PubMed

Dudbridge, Frank; Koeleman, Bobby P C

2004-09-01

Large exploratory studies, including candidate-gene-association testing, genomewide linkage-disequilibrium scans, and array-expression experiments, are becoming increasingly common. A serious problem for such studies is that statistical power is compromised by the need to control the false-positive rate for a large family of tests. Because multiple true associations are anticipated, methods have been proposed that combine evidence from the most significant tests, as a more powerful alternative to individually adjusted tests. The practical application of these methods is currently limited by a reliance on permutation testing to account for the correlated nature of single-nucleotide polymorphism (SNP)-association data. On a genomewide scale, this is both very time-consuming and impractical for repeated explorations with standard marker panels. Here, we alleviate these problems by fitting analytic distributions to the empirical distribution of combined evidence. We fit extreme-value distributions for fixed lengths of combined evidence and a beta distribution for the most significant length. An initial phase of permutation sampling is required to fit these distributions, but it can be completed more quickly than a simple permutation test and need be done only once for each panel of tests, after which the fitted parameters give a reusable calibration of the panel. Our approach is also a more efficient alternative to a standard permutation test. We demonstrate the accuracy of our approach and compare its efficiency with that of permutation tests on genomewide SNP data released by the International HapMap Consortium. The estimation of analytic distributions for combined evidence will allow these powerful methods to be applied more widely in large exploratory studies.

Mechanical Abuse Simulation and Thermal Runaway Risks of Large-Format Li-ion Batteries

DOE PAGES

Wang, Hsin; Lara-Curzio, Edgar; Rule, Evan; ...

2017-01-11

Internal short circuit of large-format Li-ion cells induced by mechanical abuse was simulated using a modified mechanical pinch test. A torsion force was added manually at ~40% maximum compressive loading force during the pinch test. The cell was twisted about 5 degrees to the side by horizontally pulling a wire attached to the anode tab. The combined torsion-compression force created small enough failure at the separator and allowed testing of fully charged large format Li-ion cells without triggering thermal runaway. Two types of commercial cells were tested using 4-6 cells at each state-of-charge (SOC). The 18 Ah LiFePO 4 (LFP)more » and 25 Ah Li(NiMnCo) 1/3O 2 (NMC) cells were tested and the thermal runaway risk (TRR) score system was used to evaluate the safety risk of the cells under the same testing conditions. The aim is to provide the cell manufacturers and end users a tool to compare different designs and safety features.« less

Mechanical Abuse Simulation and Thermal Runaway Risks of Large-Format Li-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hsin; Lara-Curzio, Edgar; Rule, Evan

Internal short circuit of large-format Li-ion cells induced by mechanical abuse was simulated using a modified mechanical pinch test. A torsion force was added manually at ~40% maximum compressive loading force during the pinch test. The cell was twisted about 5 degrees to the side by horizontally pulling a wire attached to the anode tab. The combined torsion-compression force created small enough failure at the separator and allowed testing of fully charged large format Li-ion cells without triggering thermal runaway. Two types of commercial cells were tested using 4-6 cells at each state-of-charge (SOC). The 18 Ah LiFePO 4 (LFP)more » and 25 Ah Li(NiMnCo) 1/3O 2 (NMC) cells were tested and the thermal runaway risk (TRR) score system was used to evaluate the safety risk of the cells under the same testing conditions. The aim is to provide the cell manufacturers and end users a tool to compare different designs and safety features.« less

Food waste impact on municipal solid waste angle of internal friction.

PubMed

Cho, Young Min; Ko, Jae Hac; Chi, Liqun; Townsend, Timothy G

2011-01-01

The impact of food waste content on the municipal solid waste (MSW) friction angle was studied. Using reconstituted fresh MSW specimens with different food waste content (0%, 40%, 58%, and 80%), 48 small-scale (100-mm-diameter) direct shear tests and 12 large-scale (430 mm × 430 mm) direct shear tests were performed. A stress-controlled large-scale direct shear test device allowing approximately 170-mm sample horizontal displacement was designed and used. At both testing scales, the mobilized internal friction angle of MSW decreased considerably as food waste content increased. As food waste content increased from 0% to 40% and from 40% to 80%, the mobilized internal friction angles (estimated using the mobilized peak (ultimate) shear strengths of the small-scale direct shear tests) decreased from 39° to 31° and from 31° to 7°, respectively, while those of large-scale tests decreased from 36° to 26° and from 26° to 15°, respectively. Most friction angle measurements produced in this study fell within the range of those previously reported for MSW. Copyright © 2010 Elsevier Ltd. All rights reserved.

Analysis and Ground Testing for Validation of the Inflatable Sunshield in Space (ISIS) Experiment

NASA Technical Reports Server (NTRS)

Lienard, Sebastien; Johnston, John; Adams, Mike; Stanley, Diane; Alfano, Jean-Pierre; Romanacci, Paolo

2000-01-01

The Next Generation Space Telescope (NGST) design requires a large sunshield to protect the large aperture mirror and instrument module from constant solar exposure at its L2 orbit. The structural dynamics of the sunshield must be modeled in order to predict disturbances to the observatory attitude control system and gauge effects on the line of site jitter. Models of large, non-linear membrane systems are not well understood and have not been successfully demonstrated. To answer questions about sunshield dynamic behavior and demonstrate controlled deployment, the NGST project is flying a Pathfinder experiment, the Inflatable Sunshield in Space (ISIS). This paper discusses in detail the modeling and ground-testing efforts performed at the Goddard Space Flight Center to: validate analytical tools for characterizing the dynamic behavior of the deployed sunshield, qualify the experiment for the Space Shuttle, and verify the functionality of the system. Included in the discussion will be test parameters, test setups, problems encountered, and test results.

"Fan-Tip-Drive" High-Power-Density, Permanent Magnet Electric Motor and Test Rig Designed for a Nonpolluting Aircraft Propulsion Program

NASA Technical Reports Server (NTRS)

Brown, Gerald V.; Kascak, Albert F.

2004-01-01

A scaled blade-tip-drive test rig was designed at the NASA Glenn Research Center. The rig is a scaled version of a direct-current brushless motor that would be located in the shroud of a thrust fan. This geometry is very attractive since the allowable speed of the armature is approximately the speed of the blade tips (Mach 1 or 1100 ft/s). The magnetic pressure generated in the motor acts over a large area and, thus, produces a large force or torque. This large force multiplied by the large velocity results in a high-power-density motor.

Xenografts Supplemented with Pamindronate placed in postextraction sockets to avoid crestal bone resorption. Experimental study in Fox hound dogs.

PubMed

Lozano-Carrascal, Naroa; Delgado-Ruiz, Rafael Arcesio; Gargallo-Albiol, Jordi; Maté-Sánchez, José Eduardo; Hernandez Alfaro, Federico; Calvo-Guirado, José Luis

2016-02-01

The aim of the study was to compare the effects of porcine xenografts (MP3(®)) with or without pamindronate for the healing of small and large defects of postextraction sockets. Six beagle dogs were used in the study; second premolars and first molars of the mandible were extracted, small defects (SD) and large defects (LD) were identified. Each defect was measured and randomly filled as follows: SC (small control defects filled with MP3(®) alone), ST (small test defects filled with MP3(®) modified with pamindronate), LC (large control defects filled with MP3(®) alone), LT (large test defects filled with MP3(®) modified with pamindronate). After 4 and 8 weeks, the animals were euthanized and the percentages of new bone formation (NB), residual graft (RG) and connective tissue (CT) were analysed by histology and histomorphometry of undecalcified samples. After 4 weeks, NB formation was higher for ST compared to all groups and for LT compared to LC (P < 0.05); RG was significantly higher in both control groups compared to tests (P < 0.05); and CT was higher in large defects (LC and LT) compared to small defects. After 8 weeks, NB formation was higher for test groups (ST and LT) compared to controls (P < 0.05); RG was significantly higher in both control groups compared to tests (P < 0.05); and CT was higher in large defects (LC and LT) compared to small defects (P < 0.05). Within the limitations of this experimental study, the findings suggest that porcine xenografts modified with pamindronate favours the new bone formation and increased the porcine xenograft substitution/replacement after 4 and 8 weeks of healing. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Nonlinear Analysis and Preliminary Testing Results of a Hybrid Wing Body Center Section Test Article

NASA Technical Reports Server (NTRS)

Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.; Wu, Hsi-Yung T.

2015-01-01

A large test article was recently designed, analyzed, fabricated, and successfully tested up to the representative design ultimate loads to demonstrate that stiffened composite panels with through-the-thickness reinforcement are a viable option for the next generation large transport category aircraft, including non-conventional configurations such as the hybrid wing body. This paper focuses on finite element analysis and test data correlation of the hybrid wing body center section test article under mechanical, pressure and combined load conditions. Good agreement between predictive nonlinear finite element analysis and test data is found. Results indicate that a geometrically nonlinear analysis is needed to accurately capture the behavior of the non-circular pressurized and highly-stressed structure when the design approach permits local buckling.

Large Field Photogrammetry Techniques in Aircraft and Spacecraft Impact Testing

NASA Technical Reports Server (NTRS)

Littell, Justin D.

2010-01-01

The Landing and Impact Research Facility (LandIR) at NASA Langley Research Center is a 240 ft. high A-frame structure which is used for full-scale crash testing of aircraft and rotorcraft vehicles. Because the LandIR provides a unique capability to introduce impact velocities in the forward and vertical directions, it is also serving as the facility for landing tests on full-scale and sub-scale Orion spacecraft mass simulators. Recently, a three-dimensional photogrammetry system was acquired to assist with the gathering of vehicle flight data before, throughout and after the impact. This data provides the basis for the post-test analysis and data reduction. Experimental setups for pendulum swing tests on vehicles having both forward and vertical velocities can extend to 50 x 50 x 50 foot cubes, while weather, vehicle geometry, and other constraints make each experimental setup unique to each test. This paper will discuss the specific calibration techniques for large fields of views, camera and lens selection, data processing, as well as best practice techniques learned from using the large field of view photogrammetry on a multitude of crash and landing test scenarios unique to the LandIR.

Comments on the origin of acoustic emission in fatigue testing of aluminum alloys

NASA Astrophysics Data System (ADS)

Heiple, C. R.; Carpenter, S. H.; Armentrout, D. L.

The size of acoustic emission (AE) signals expected from inclusion fracture during fatigue testing of 7075 aluminum has been estimated on the basis of previous measurements of AE produced by the fracture of boron particles incorporated into 2219 aluminum. The AF signal size expected from deformation in the plastic zone ahead of the fatigue crack was estimated from the results of tensile tests on 7075 aluminum. The signals predicted from both processes are near or below the noise level in the fatigue experiments and are therefore far too small to account for the signals actually observed. Nearly simultaneous fracture of multiple inclusions could produce signals as large as those observed in fatigue tests of 7075 aluminum, however, fatigue tests of 7050 aluminum produced signals as large or larger than in 7075. Since 7050 has substantially fewer inclusions than 7075, the simultaneous failure of multiple inclusions is unlikely to be a major AE source in fatigue testing of either aluminum alloy. Thus, the most probable source of acoustic emission during fatigue testing of 7075 and 7050 aluminum is the crack advance itself. The measured crack advance per cycle is large enough to release sufficient elastic energy to account for the AE signals observed.

Noncontact methods for optical testing of convex aspheric mirrors for future large telescopes

NASA Astrophysics Data System (ADS)

Goncharov, Alexander V.; Druzhin, Vladislav V.; Batshev, Vladislav I.

2009-06-01

Non-contact methods for testing of large rotationally symmetric convex aspheric mirrors are proposed. These methods are based on non-null testing with side illumination schemes, in which a narrow collimated beam is reflected from the meridional aspheric profile of a mirror. The figure error of the mirror is deduced from the intensity pattern from the reflected beam obtained on a screen, which is positioned in the tangential plane (containing the optical axis) and perpendicular to the incoming beam. Testing of the entire surface is carried out by rotating the mirror about its optical axis and registering the characteristics of the intensity pattern on the screen. The intensity pattern can be formed using three different techniques: modified Hartman test, interference and boundary curve test. All these techniques are well known but have not been used in the proposed side illumination scheme. Analytical expressions characterizing the shape and location of the intensity pattern on the screen or a CCD have been developed for all types of conic surfaces. The main advantage of these testing methods compared with existing methods (Hindle sphere, null lens, computer generated hologram) is that the reference system does not require large optical components.

Space Shuttle Solid Rocket Booster decelerator subsystem - Air drop test vehicle/B-52 design

NASA Technical Reports Server (NTRS)

Runkle, R. E.; Drobnik, R. F.

1979-01-01

The air drop development test program for the Space Shuttle Solid Rocket Booster Recovery System required the design of a large drop test vehicle that would meet all the stringent requirements placed on it by structural loads, safety considerations, flight recovery system interfaces, and sequence. The drop test vehicle had to have the capability to test the drogue and the three main parachutes both separately and in the total flight deployment sequence and still be low-cost to fit in a low-budget development program. The design to test large ribbon parachutes to loads of 300,000 pounds required the detailed investigation and integration of several parameters such as carrier aircraft mechanical interface, drop test vehicle ground transportability, impact point ground penetration, salvageability, drop test vehicle intelligence, flight design hardware interfaces, and packaging fidelity.

V/STOL wind-tunnel testing

NASA Technical Reports Server (NTRS)

Koenig, D. G.

1984-01-01

Factors influencing effective program planning for V/STOL wind-tunnel testing are discussed. The planning sequence itself, which includes a short checklist of considerations that could enhance the value of the tests, is also described. Each of the considerations, choice of wind tunnel, type of model installation, model development and test operations, is discussed, and examples of appropriate past and current V/STOL test programs are provided. A short survey of the moderate to large subsonic wind tunnels is followed by a review of several model installations, from two-dimensional to large-scale models of complete aircraft configurations. Model sizing, power simulation, and planning are treated, including three areas is test operations: data-acquisition systems, acoustic measurements in wind tunnels, and flow surveying.

Potential Damage to Flight Hardware from MIL-STD-462 CS02 Setup

NASA Technical Reports Server (NTRS)

Harris, Patrick K.; Block, Nathan F.

2003-01-01

The MIL-STD-462 CS02 conducted susceptibility test setup includes an audio transformer, with the secondary used as an inductor, and a large capacitor. Together, these two components form an L-type low-pass filter to minimize the injected test signal input into the power source. Some flight hardware power input configurations are not compatible with this setup and break into oscillation when powered up. This, in turn, can damage flight hardware. Such an oscillation resulted in the catastrophic failure of an item tested in the Goddard Space Flight Center (GSFC) Large electromagnetic compatibility (EMC) Test Facility.

Multipacting simulation and test results of BNL 704 MHz SRF gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu W.; Belomestnykh, S.; Ben-Zvi, I.

The BNL 704MHz SRF gun has a grooved choke joint to support the photo-cathode. Due to the distortion of grooves at the choke joint during the BCP for the choke joint, several multipacting barriers showed up when it was tested with Nb cathode stalk at JLab. We built a setup to use the spare large grain SRF cavity to test and condition the multipacting at BNL with various power sources up to 50kW. The test is carried out in three stages: testing the cavity performance without cathode, testing the cavity with the Nb cathode stalk that was used at Jlab,more » and testing the cavity with a copper cathode stalk that is based on the design for the SRF gun. This paper summarizes the results of multipacting simulation, and presents the large grain cavity test setup and the test results.« less

Small-scale dynamic confinement gap test

NASA Astrophysics Data System (ADS)

Cook, Malcolm

2011-06-01

Gap tests are routinely used to ascertain the shock sensitiveness of new explosive formulations. The tests are popular since that are easy and relatively cheap to perform. However, with modern insensitive formulations with big critical diameters, large test samples are required. This can make testing and screening of new formulations expensive since large quantities of test material are required. Thus a new test that uses significantly smaller sample quantities would be very beneficial. In this paper we describe a new small-scale test that has been designed using our CHARM ignition and growth routine in the DYNA2D hydrocode. The new test is a modified gap test and uses detonating nitromethane to provide dynamic confinement (instead of a thick metal case) whilst exposing the sample to a long duration shock wave. The long duration shock wave allows less reactive materials that are below their critical diameter, more time to react. We present details on the modelling of the test together with some preliminary experiments to demonstrate the potential of the new test method.

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Packaging unsafe for transportation and no loss of contents. (2) For flexible Large Packagings, there may be no deterioration which renders the Large Packaging unsafe for transportation and no loss of contents... required load, there is no permanent deformation to the Large Packaging which renders the whole Large...

Performance of the Anti-Coincidence Detector on the GLAST Large Area Telescope

NASA Technical Reports Server (NTRS)

Thompson, D. J.; Charles, E.; Hartman, R. C.; Moiseev, A. A.; Ormes, J. F.

2007-01-01

The Anti-Coincidence Detector (ACD), the outermost detector layer in the Gamma-ray Large Area Space Telescope (GLAST) Large Area Telescope (LAT), is designed to detect and veto incident cosmic ray charged particles, which outnumber cosmic gamma rays by 3-4 orders of magnitude. The challenge in ACD design is that it must have high (0.9997) detection efficiency for singly-charged relativistic particles, but must also have a low probability for self-veto of high-energy gammas by backplash radiation from interactions in the LAT calorimeter. Simulations and tests demonstrate that the ACD meete its design requirements. The performance of the ACD has remained stable thrugh stand-alone environmental testing, shipment across the U.S. installation onto the LAT, shipment back across the U.S., LAT environmental testing, and shipment to Arizona. As part of the fully-assembled GLAST observatory, the ACD is being readied for final testing before launch.

Large transient fault current test of an electrical roll ring

NASA Technical Reports Server (NTRS)

Yenni, Edward J.; Birchenough, Arthur G.

1992-01-01

The space station uses precision rotary gimbals to provide for sun tracking of its photoelectric arrays. Electrical power, command signals and data are transferred across the gimbals by roll rings. Roll rings have been shown to be capable of highly efficient electrical transmission and long life, through tests conducted at the NASA Lewis Research Center and Honeywell's Satellite and Space Systems Division in Phoenix, AZ. Large potential fault currents inherent to the power system's DC distribution architecture, have brought about the need to evaluate the effects of large transient fault currents on roll rings. A test recently conducted at Lewis subjected a roll ring to a simulated worst case space station electrical fault. The system model used to obtain the fault profile is described, along with details of the reduced order circuit that was used to simulate the fault. Test results comparing roll ring performance before and after the fault are also presented.

Wind-Tunnel Tests on a Series of Wing Models Through a Large Angle of Attack Range. Part I : Force Tests

NASA Technical Reports Server (NTRS)

Knight, Montgomery; Wenzinger, Carl J

1930-01-01

This investigation covers force tests through a large range of angle of attack on a series of monoplane and biplane wing models. The tests were conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The models were arranged in such a manner as to make possible a determination of the effects of variations in tip shape, aspect ratio, flap setting, stagger, gap, decalage, sweep back, and airfoil profile. The arrangements represented most of the types of wing systems in use on modern airplanes. The effect of each variable is illustrated by means of groups of curves. In addition, there are included approximate autorotational characteristics in the form of calculated ranges of "rotary instability." a correction for blocking in this tunnel which applies to monoplanes at large angles of attack has been developed, and is given in an appendix. (author)

Fabrication and radio frequency test of large-area MgB 2 films on niobium substrates

DOE PAGES

Ni, Zhimao; Guo, Xin; Welander, Paul B.; ...

2017-01-19

Magnesium diboride (MgB 2) is a promising candidate material for superconducting radio frequency (RF) cavities because of its higher transition temperature and critical field compared with niobium. To meet the demand of RF test devices, the fabrication of large-area MgB 2 films on metal substrates is needed. Here, in this work, high quality MgB 2 films with 50 mm diameter were fabricated on niobium by using an improved HPCVD system at Peking University, and RF tests were carried out at SLAC National Accelerator Laboratory. The transition temperature is approximately 39.6 K and the RF surface resistance is about 120 μΩmore » at 4 K and 11.4 GHz. Finally, the fabrication processes, surface morphology, DC superconducting properties and RF tests of these large-area MgB 2 films are presented.« less

Fabrication and radio frequency test of large-area MgB 2 films on niobium substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ni, Zhimao; Guo, Xin; Welander, Paul B.

Magnesium diboride (MgB 2) is a promising candidate material for superconducting radio frequency (RF) cavities because of its higher transition temperature and critical field compared with niobium. To meet the demand of RF test devices, the fabrication of large-area MgB 2 films on metal substrates is needed. Here, in this work, high quality MgB 2 films with 50 mm diameter were fabricated on niobium by using an improved HPCVD system at Peking University, and RF tests were carried out at SLAC National Accelerator Laboratory. The transition temperature is approximately 39.6 K and the RF surface resistance is about 120 μΩmore » at 4 K and 11.4 GHz. Finally, the fabrication processes, surface morphology, DC superconducting properties and RF tests of these large-area MgB 2 films are presented.« less

Fire extinguishing tests -80 with methyl alcohol gasoline

NASA Astrophysics Data System (ADS)

Holmstedt, G.; Ryderman, A.; Carlsson, B.; Lennmalm, B.

1980-10-01

Large scale tests and laboratory experiments were carried out for estimating the extinguishing effectiveness of three alcohol resistant aqueous film forming foams (AFFF), two alcohol resistant fluoroprotein foams and two detergent foams in various poolfires: gasoline, isopropyl alcohol, acetone, methyl-ethyl ketone, methyl alcohol and M15 (a gasoline, methyl alcohol, isobutene mixture). The scaling down of large scale tests for developing a reliable laboratory method was especially examined. The tests were performed with semidirect foam application, in pools of 50, 11, 4, 0.6, and 0.25 sq m. Burning time, temperature distribution in the liquid, and thermal radiation were determined. An M15 fire can be extinguished with a detergent foam, but it is impossible to extinguish fires in polar solvents, such as methyl alcohol, acetone, and isopropyl alcohol with detergent foams, AFFF give the best results; and performances with small pools can hardly be correlated with results from large scale fires.

Reliability Testing of NASA Piezocomposite Actuators

NASA Technical Reports Server (NTRS)

Wilkie, W.; High, J.; Bockman, J.

2002-01-01

NASA Langley Research Center has developed a low-cost piezocomposite actuator which has application for controlling vibrations in large inflatable smart space structures, space telescopes, and high performance aircraft. Tests show the NASA piezocomposite device is capable of producing large, directional, in-plane strains on the order of 2000 parts-per-million peak-to-peak, with no reduction in free-strain performance to 100 million electrical cycles. This paper describes methods, measurements, and preliminary results from our reliability evaluation of the device under externally applied mechanical loads and at various operational temperatures. Tests performed to date show no net reductions in actuation amplitude while the device was moderately loaded through 10 million electrical cycles. Tests were performed at both room temperature and at the maximum operational temperature of the epoxy resin system used in manufacture of the device. Initial indications are that actuator reliability is excellent, with no actuator failures or large net reduction in actuator performance.

Large-scale academic achievement testing of deaf and hard-of-hearing students: past, present, and future.

PubMed

Qi, Sen; Mitchell, Ross E

2012-01-01

The first large-scale, nationwide academic achievement testing program using Stanford Achievement Test (Stanford) for deaf and hard-of-hearing children in the United States started in 1969. Over the past three decades, the Stanford has served as a benchmark in the field of deaf education for assessing student academic achievement. However, the validity and reliability of using the Stanford for this special student population still require extensive scrutiny. Recent shifts in educational policy environment, which require that schools enable all children to achieve proficiency through accountability testing, warrants a close examination of the adequacy and relevance of the current large-scale testing of deaf and hard-of-hearing students. This study has three objectives: (a) it will summarize the historical data over the last three decades to indicate trends in academic achievement for this special population, (b) it will analyze the current federal laws and regulations related to educational testing and special education, thereby identifying gaps between policy and practice in the field, especially identifying the limitations of current testing programs in assessing what deaf and hard-of-hearing students know, and (c) it will offer some insights and suggestions for future testing programs for deaf and hard-of-hearing students.

Summary of LaRC 2-inch Erectable Joint Hardware Heritage Test Data

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Watson, Judith J.

2016-01-01

As the National Space Transportation System (STS, also known as the Space Shuttle) went into service during the early 1980's, NASA envisioned many missions of exploration and discovery that could take advantage of the STS capabilities. These missions included: large orbiting space stations, large space science telescopes and large spacecraft for manned missions to the Moon and Mars. The missions required structures that were significantly larger than the payload volume available on the STS. NASA Langley Research Center (LaRC) conducted studies to design and develop the technology needed to assemble the large space structures in orbit. LaRC focused on technology for erectable truss structures, in particular, the joint that connects the truss struts at the truss nodes. When the NASA research in large erectable space structures ended in the early 1990's, a significant amount of structural testing had been performed on the LaRC 2-inch erectable joint that was never published. An extensive set of historical information and data has been reviewed and the joint structural testing results from this historical data are compiled and summarized in this report.

A fast boosting-based screening method for large-scale association study in complex traits with genetic heterogeneity.

PubMed

Wang, Lu-Yong; Fasulo, D

2006-01-01

Genome-wide association study for complex diseases will generate massive amount of single nucleotide polymorphisms (SNPs) data. Univariate statistical test (i.e. Fisher exact test) was used to single out non-associated SNPs. However, the disease-susceptible SNPs may have little marginal effects in population and are unlikely to retain after the univariate tests. Also, model-based methods are impractical for large-scale dataset. Moreover, genetic heterogeneity makes the traditional methods harder to identify the genetic causes of diseases. A more recent random forest method provides a more robust method for screening the SNPs in thousands scale. However, for more large-scale data, i.e., Affymetrix Human Mapping 100K GeneChip data, a faster screening method is required to screening SNPs in whole-genome large scale association analysis with genetic heterogeneity. We propose a boosting-based method for rapid screening in large-scale analysis of complex traits in the presence of genetic heterogeneity. It provides a relatively fast and fairly good tool for screening and limiting the candidate SNPs for further more complex computational modeling task.

Modal Vibration Analysis of Large Castings

NASA Technical Reports Server (NTRS)

Werlink, Rudolph J.; Margasahayam, Ravi N.

2009-01-01

The art of experimental modal vibration analysis (MVA) has been extended to apply to large castings. This extension was made to enable the use of experimental MVA as a relatively inexpensive, simple means of assessing the internal structural integrity of tread shoes of crawler transporters used to move spacecraft to the launch pad at Kennedy Space Center. Each tread shoe is made from cast iron and weighs about a ton (has a mass .907 kg). The present extended version of experimental MVA could also be applied to other large castings. It could be especially useful to manufacturers as a means of rapidly discriminating against large castings that contain unacceptably large concentrations of internal defects. The use of experimental MVA to assess structural integrity is not new. What are new here are those aspects of the extension of experimental MVA that pertain to the application of MVA to objects so massive that it may not be practical or cost effective to mount them in special test fixtures that impose special test boundary conditions to test them in place under normal conditions of use.

Utilizing the ultrasensitive Schistosoma up-converting phosphor lateral flow circulating anodic antigen (UCP-LF CAA) assay for sample pooling-strategies.

PubMed

Corstjens, Paul L A M; Hoekstra, Pytsje T; de Dood, Claudia J; van Dam, Govert J

2017-11-01

Methodological applications of the high sensitivity genus-specific Schistosoma CAA strip test, allowing detection of single worm active infections (ultimate sensitivity), are discussed for efficient utilization in sample pooling strategies. Besides relevant cost reduction, pooling of samples rather than individual testing can provide valuable data for large scale mapping, surveillance, and monitoring. The laboratory-based CAA strip test utilizes luminescent quantitative up-converting phosphor (UCP) reporter particles and a rapid user-friendly lateral flow (LF) assay format. The test includes a sample preparation step that permits virtually unlimited sample concentration with urine, reaching ultimate sensitivity (single worm detection) at 100% specificity. This facilitates testing large urine pools from many individuals with minimal loss of sensitivity and specificity. The test determines the average CAA level of the individuals in the pool thus indicating overall worm burden and prevalence. When requiring test results at the individual level, smaller pools need to be analysed with the pool-size based on expected prevalence or when unknown, on the average CAA level of a larger group; CAA negative pools do not require individual test results and thus reduce the number of tests. Straightforward pooling strategies indicate that at sub-population level the CAA strip test is an efficient assay for general mapping, identification of hotspots, determination of stratified infection levels, and accurate monitoring of mass drug administrations (MDA). At the individual level, the number of tests can be reduced i.e. in low endemic settings as the pool size can be increased as opposed to prevalence decrease. At the sub-population level, average CAA concentrations determined in urine pools can be an appropriate measure indicating worm burden. Pooling strategies allowing this type of large scale testing are feasible with the various CAA strip test formats and do not affect sensitivity and specificity. It allows cost efficient stratified testing and monitoring of worm burden at the sub-population level, ideally for large-scale surveillance generating hard data for performance of MDA programs and strategic planning when moving towards transmission-stop and elimination.

Testing a New Generation: Implementing Clickers as an Extension Data Collection Tool

ERIC Educational Resources Information Center

Parmer, Sondra M.; Parmer, Greg; Struempler, Barb

2012-01-01

Using clickers to gauge student understanding in large classrooms is well documented. Less well known is the effectiveness of using clickers with youth for test taking in large-scale Extension programs. This article describes the benefits and challenges of collecting evaluation data using clickers with a third-grade population participating in a…

Facilitating Learning in Large Lecture Classes: Testing the "Teaching Team" Approach to Peer Learning

ERIC Educational Resources Information Center

Stanger-Hall, Kathrin F.; Lang, Sarah; Maas, Martha

2010-01-01

We tested the effect of voluntary peer-facilitated study groups on student learning in large introductory biology lecture classes. The peer facilitators (preceptors) were trained as part of a Teaching Team (faculty, graduate assistants, and preceptors) by faculty and Learning Center staff. Each preceptor offered one weekly study group to all…

Interrater Reliability in Large-Scale Assessments--Can Teachers Score National Tests Reliably without External Controls?

ERIC Educational Resources Information Center

Pantzare, Anna Lind

2015-01-01

In most large-scale assessment systems a set of rather expensive external quality controls are implemented in order to guarantee the quality of interrater reliability. This study empirically examines if teachers' ratings of national tests in mathematics can be reliable without using monitoring, training, or other methods of external quality…

Status of JUPITER Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Inoue, T.; Shirakata, K.; Kinjo, K.

To obtain the data necessary for evaluating the nuclear design method of a large-scale fast breeder reactor, criticality tests with a large- scale homogeneous reactor were conducted as part of a joint research program by Japan and the U.S. Analyses of the tests are underway in both countries. The purpose of this paper is to describe the status of this project.

Changing the English Classroom: When Large-Scale "Common" Testing Meets Secondary Curriculum and Instruction in the United States

ERIC Educational Resources Information Center

Cimbricz, Sandra K.; McConn, Matthew L.

2015-01-01

This article explores the intersection of new, large-scale standards-based testing, teacher accountability policy, and secondary curriculum and instruction in the United States. Two federally funded consortia--the Smarter Balanced Assessment Consortium and the Partnership for Readiness of College and Careers--prove focal to this paper, as these…

NREL Scientists and Engineers Recognized for Top Innovations | NREL | News

Science.gov Websites

commercially available, large-format isothermal battery calorimeter for lithium-ion battery safety testing to test the performance and safety of large-format lithium-ion batteries used extensively in electric develop NREL intellectual property representing an isothermal battery calorimeter. The technical

Preliminary eddy current modelling for the large angle magnetic suspension test fixture

NASA Technical Reports Server (NTRS)

Britcher, Colin

1994-01-01

This report presents some recent developments in the mathematical modeling of the Large Angle Magnetic Suspension Test Fixture (LAMSTF) at NASA Langley Research Center. It is shown that these effects are significant, but may be amenable to analysis, modeling and measurement. A theoretical framework is presented, together with a comparison of computed and experimental data.

First results of the ITER-relevant negative ion beam test facility ELISE (invited).

PubMed

Fantz, U; Franzen, P; Heinemann, B; Wünderlich, D

2014-02-01

An important step in the European R&D roadmap towards the neutral beam heating systems of ITER is the new test facility ELISE (Extraction from a Large Ion Source Experiment) for large-scale extraction from a half-size ITER RF source. The test facility was constructed in the last years at Max-Planck-Institut für Plasmaphysik Garching and is now operational. ELISE is gaining early experience of the performance and operation of large RF-driven negative hydrogen ion sources with plasma illumination of a source area of 1 × 0.9 m(2) and an extraction area of 0.1 m(2) using 640 apertures. First results in volume operation, i.e., without caesium seeding, are presented.

Testing of Large Diameter Fresnel Optics for Space Based Observations of Extensive Air Showers

NASA Technical Reports Server (NTRS)

Adams, James H.; Christl, Mark J.; Young, Roy M.

2011-01-01

The JEM-EUSO mission will detect extensive air showers produced by extreme energy cosmic rays. It operates from the ISS looking down on Earth's night time atmosphere to detect the nitrogen fluorescence and Cherenkov produce by the charged particles in the EAS. The JEM-EUSO science objectives require a large field of view, sensitivity to energies below 50 EeV, and must fit within available ISS resources. The JEM-EUSO optic module uses three large diameter, thin plastic lenses with Fresnel surfaces to meet the instrument requirements. A bread-board model of the optic has been manufactured and has undergone preliminary tests. We report the results of optical performance tests and evaluate the present capability to manufacture these optical elements.

Liquid Oxygen Propellant Densification Production and Performance Test Results With a Large-Scale Flight-Weight Propellant Tank for the X33 RLV

NASA Technical Reports Server (NTRS)

Tomsik, Thomas M.; Meyer, Michael L.

2010-01-01

This paper describes in-detail a test program that was initiated at the Glenn Research Center (GRC) involving the cryogenic densification of liquid oxygen (LO2). A large scale LO2 propellant densification system rated for 200 gpm and sized for the X-33 LO2 propellant tank, was designed, fabricated and tested at the GRC. Multiple objectives of the test program included validation of LO2 production unit hardware and characterization of densifier performance at design and transient conditions. First, performance data is presented for an initial series of LO2 densifier screening and check-out tests using densified liquid nitrogen. The second series of tests show performance data collected during LO2 densifier test operations with liquid oxygen as the densified product fluid. An overview of LO2 X-33 tanking operations and load tests with the 20,000 gallon Structural Test Article (STA) are described. Tank loading testing and the thermal stratification that occurs inside of a flight-weight launch vehicle propellant tank were investigated. These operations involved a closed-loop recirculation process of LO2 flow through the densifier and then back into the STA. Finally, in excess of 200,000 gallons of densified LO2 at 120 oR was produced with the propellant densification unit during the demonstration program, an achievement that s never been done before in the realm of large-scale cryogenic tests.

Modified surface testing method for large convex aspheric surfaces based on diffraction optics.

PubMed

Zhang, Haidong; Wang, Xiaokun; Xue, Donglin; Zhang, Xuejun

2017-12-01

Large convex aspheric optical elements have been widely applied in advanced optical systems, which have presented a challenging metrology problem. Conventional testing methods cannot satisfy the demand gradually with the change of definition of "large." A modified method is proposed in this paper, which utilizes a relatively small computer-generated hologram and an illumination lens with certain feasibility to measure the large convex aspherics. Two example systems are designed to demonstrate the applicability, and also, the sensitivity of this configuration is analyzed, which proves the accuracy of the configuration can be better than 6 nm with careful alignment and calibration of the illumination lens in advance. Design examples and analysis show that this configuration is applicable to measure the large convex aspheric surfaces.

The advantages and disadvantages of using the TREAT reactor for nuclear laser experiments

NASA Astrophysics Data System (ADS)

Dickson, P. W.; Snyder, A. M.; Imel, G. R.; McConnell, R. J.

The Transient Reactor Test Facility (TREAT) is a large air-cooled test facility located at the Idaho National Engineering Laboratory. Two of the major design features of TREAT, its large size and its being an air-cooled reactor, provide clues to both its advantages and disadvantages for supporting nuclear laser experiments. Its large size, which is dictated by the dilute uranium/graphite fuel, permits accommodation of geometrically large experiments. However, TREAT's large size also results in relatively long transients so that the energy deposited in an experiment is large relative to the peak power available from the reactor. TREAT's air-cooling mode of operation allows its configuration to be changed fairly readily. Due to air cooling, the reactor cools down slowly, permitting only one full power transient a day, which can be a disadvantage in some experimental programs. The reactor is capable of both steady-state or transient operation.

Workplace drug testing and worker drug use.

PubMed

Carpenter, Christopher S

2007-04-01

To examine the nature and extent of the association between workplace drug testing and worker drug use. Repeated cross-sections from the 2000 to 2001 National Household Surveys on Drug Abuse (NHSDA) and the 2002 National Survey on Drug Use and Health (NSDUH). Multivariate logistic regression models of the likelihood of marijuana use are estimated as a function of several different workplace drug policies, including drug testing. Specific questions about penalty severity and the likelihood of detection are used to further evaluate the nature of the association. Individuals whose employers perform drug tests are significantly less likely to report past month marijuana use, even after controlling for a wide array of worker and job characteristics. However, large negative associations are also found for variables indicating whether a firm has drug education, an employee assistance program, or a simple written policy about substance use. Accounting for these other workplace characteristics reduces-but does not eliminate-the testing differential. Frequent testing and severe penalties reduce the likelihood that workers use marijuana. Previous studies have interpreted the large negative correlation between workplace drug testing and employee substance use as representing a causal deterrent effect of drug testing. Our results using more comprehensive data suggest that these estimates have been slightly overstated due to omitted variables bias. The overall pattern of results remains largely consistent with the hypothesis that workplace drug testing deters worker drug use.

When the test of mediation is more powerful than the test of the total effect.

PubMed

O'Rourke, Holly P; MacKinnon, David P

2015-06-01

Although previous research has studied power in mediation models, the extent to which the inclusion of a mediator will increase power has not been investigated. To address this deficit, in a first study we compared the analytical power values of the mediated effect and the total effect in a single-mediator model, to identify the situations in which the inclusion of one mediator increased statistical power. The results from this first study indicated that including a mediator increased statistical power in small samples with large coefficients and in large samples with small coefficients, and when coefficients were nonzero and equal across models. Next, we identified conditions under which power was greater for the test of the total mediated effect than for the test of the total effect in the parallel two-mediator model. These results indicated that including two mediators increased power in small samples with large coefficients and in large samples with small coefficients, the same pattern of results that had been found in the first study. Finally, we assessed the analytical power for a sequential (three-path) two-mediator model and compared the power to detect the three-path mediated effect to the power to detect both the test of the total effect and the test of the mediated effect for the single-mediator model. The results indicated that the three-path mediated effect had more power than the mediated effect from the single-mediator model and the test of the total effect. Practical implications of these results for researchers are then discussed.

James Webb Space Telescope Core 2 Test - Cryogenic Thermal Balance Test of the Observatorys Core Area Thermal Control Hardware

NASA Technical Reports Server (NTRS)

Cleveland, Paul; Parrish, Keith; Thomson, Shaun; Marsh, James; Comber, Brian

2016-01-01

The James Webb Space Telescope (JWST), successor to the Hubble Space Telescope, will be the largest astronomical telescope ever sent into space. To observe the very first light of the early universe, JWST requires a large deployed 6.5-meter primary mirror cryogenically cooled to less than 50 Kelvin. Three scientific instruments are further cooled via a large radiator system to less than 40 Kelvin. A fourth scientific instrument is cooled to less than 7 Kelvin using a combination pulse-tube Joule-Thomson mechanical cooler. Passive cryogenic cooling enables the large scale of the telescope which must be highly folded for launch on an Ariane 5 launch vehicle and deployed once on orbit during its journey to the second Earth-Sun Lagrange point. Passive cooling of the observatory is enabled by the deployment of a large tennis court sized five layer Sunshield combined with the use of a network of high efficiency radiators. A high purity aluminum heat strap system connects the three instrument's detector systems to the radiator systems to dissipate less than a single watt of parasitic and instrument dissipated heat. JWST's large scale features, while enabling passive cooling, also prevent the typical flight configuration fully-deployed thermal balance test that is the keystone of most space missions' thermal verification plans. This paper describes the JWST Core 2 Test, which is a cryogenic thermal balance test of a full size, high fidelity engineering model of the Observatory's 'Core' area thermal control hardware. The 'Core' area is the key mechanical and cryogenic interface area between all Observatory elements. The 'Core' area thermal control hardware allows for temperature transition of 300K to approximately 50 K by attenuating heat from the room temperature IEC (instrument electronics) and the Spacecraft Bus. Since the flight hardware is not available for test, the Core 2 test uses high fidelity and flight-like reproductions.

Large-Scale Cryogen Systems and Test Facilities

NASA Technical Reports Server (NTRS)

Johnson, R. G.; Sass, J. P.; Hatfield, W. H.

2007-01-01

NASA has completed initial construction and verification testing of the Integrated Systems Test Facility (ISTF) Cryogenic Testbed. The ISTF is located at Complex 20 at Cape Canaveral Air Force Station, Florida. The remote and secure location is ideally suited for the following functions: (1) development testing of advanced cryogenic component technologies, (2) development testing of concepts and processes for entire ground support systems designed for servicing large launch vehicles, and (3) commercial sector testing of cryogenic- and energy-related products and systems. The ISTF Cryogenic Testbed consists of modular fluid distribution piping and storage tanks for liquid oxygen/nitrogen (56,000 gal) and liquid hydrogen (66,000 gal). Storage tanks for liquid methane (41,000 gal) and Rocket Propellant 1 (37,000 gal) are also specified for the facility. A state-of-the-art blast proof test command and control center provides capability for remote operation, video surveillance, and data recording for all test areas.

Utilization of arterial blood gas measurements in a large tertiary care hospital.

PubMed

Melanson, Stacy E F; Szymanski, Trevor; Rogers, Selwyn O; Jarolim, Petr; Frendl, Gyorgy; Rawn, James D; Cooper, Zara; Ferrigno, Massimo

2007-04-01

We describe the patterns of utilization of arterial blood gas (ABG) tests in a large tertiary care hospital. To our knowledge, no hospital-wide analysis of ABG test utilization has been published. We analyzed 491 ABG tests performed during 24 two-hour intervals, representative of different staff shifts throughout the 7-day week. The clinician ordering each ABG test was asked to fill out a utilization survey. The most common reasons for requesting an ABG test were changes in ventilator settings (27.6%), respiratory events (26.4%), and routine (25.7%). Of the results, approximately 79% were expected, and a change in patient management (eg, a change in ventilator settings) occurred in 42% of cases. Many ABG tests were ordered as part of a clinical routine or to monitor parameters that can be assessed clinically or through less invasive testing. Implementation of practice guidelines may prove useful in controlling test utilization and in decreasing costs.

Experimental instrumentation system for the Phased Array Mirror Extendible Large Aperture (PAMELA) test program

NASA Technical Reports Server (NTRS)

Boykin, William H., Jr.

1993-01-01

Adaptive optics are used in telescopes for both viewing objects with minimum distortion and for transmitting laser beams with minimum beam divergence and dance. In order to test concepts on a smaller scale, NASA MSFC is in the process of setting up an adaptive optics test facility with precision (fraction of wavelengths) measurement equipment. The initial system under test is the adaptive optical telescope called PAMELA (Phased Array Mirror Extendible Large Aperture). Goals of this test are: assessment of test hardware specifications for PAMELA application and the determination of the sensitivities of instruments for measuring PAMELA (and other adaptive optical telescopes) imperfections; evaluation of the PAMELA system integration effort and test progress and recommended actions to enhance these activities; and development of concepts and prototypes of experimental apparatuses for PAMELA.

Absolute measurements of large mirrors

NASA Astrophysics Data System (ADS)

Su, Peng

The ability to produce mirrors for large astronomical telescopes is limited by the accuracy of the systems used to test the surfaces of such mirrors. Typically the mirror surfaces are measured by comparing their actual shapes to a precision master, which may be created using combinations of mirrors, lenses, and holograms. The work presented here develops several optical testing techniques that do not rely on a large or expensive precision, master reference surface. In a sense these techniques provide absolute optical testing. The Giant Magellan Telescope (GMT) has been designed with a 350 m 2 collecting area provided by a 25 m diameter primary mirror made out from seven circular independent mirror segments. These segments create an equivalent f/0.7 paraboloidal primary mirror consisting of a central segment and six outer segments. Each of the outer segments is 8.4 m in diameter and has an off-axis aspheric shape departing 14.5 mm from the best-fitting sphere. Much of the work in this dissertation is motivated by the need to measure the surfaces or such large mirrors accurately, without relying on a large or expensive precision reference surface. One method for absolute testing describing in this dissertation uses multiple measurements relative to a reference surface that is located in different positions with respect to the test surface of interest. The test measurements are performed with an algorithm that is based on the maximum likelihood (ML) method. Some methodologies for measuring large flat surfaces in the 2 m diameter range and for measuring the GMT primary mirror segments were specifically developed. For example, the optical figure of a 1.6-m flat mirror was determined to 2 nm rms accuracy using multiple 1-meter sub-aperture measurements. The optical figure of the reference surface used in the 1-meter sub-aperture measurements was also determined to the 2 nm level. The optical test methodology for a 1.7-m off axis parabola was evaluated by moving several times the mirror under test in relation to the test system. The result was a separation of errors in the optical test system to those errors from the mirror under test. This method proved to be accurate to 12nm rms. Another absolute measurement technique discussed in this dissertation utilizes the property of a paraboloidal surface of reflecting rays parallel to its optical axis, to its focal point. We have developed a scanning pentaprism technique that exploits this geometry to measure off-axis paraboloidal mirrors such as the GMT segments. This technique was demonstrated on a 1.7 m diameter prototype and proved to have a precision of about 50 nm rms.

Altering Test Environments for Reducing Test Anxiety and for Improving Academic Performance.

ERIC Educational Resources Information Center

Bushnell, Don D.

To test the effects of altering situational variables in stressful examinations on high test anxious and low test anxious undergraduates, mid-terms and final examinations were administered in two environmental settings: large lecture halls and small language laboratories. Mean test scores for high test anxious students in the language labs were…

Detection of Test Collusion via Kullback-Leibler Divergence

ERIC Educational Resources Information Center

Belov, Dmitry I.

2013-01-01

The development of statistical methods for detecting test collusion is a new research direction in the area of test security. Test collusion may be described as large-scale sharing of test materials, including answers to test items. Current methods of detecting test collusion are based on statistics also used in answer-copying detection.…

High-Stakes Accountability: Student Anxiety and Large-Scale Testing

ERIC Educational Resources Information Center

von der Embse, Nathaniel P.; Witmer, Sara E.

2014-01-01

This study examined the relationship between student anxiety about high-stakes testing and their subsequent test performance. The FRIEDBEN Test Anxiety Scale was administered to 1,134 11th-grade students, and data were subsequently collected on their statewide assessment performance. Test anxiety was a significant predictor of test performance…

Longitudinal Multistage Testing

ERIC Educational Resources Information Center

Pohl, Steffi

2013-01-01

This article introduces longitudinal multistage testing (lMST), a special form of multistage testing (MST), as a method for adaptive testing in longitudinal large-scale studies. In lMST designs, test forms of different difficulty levels are used, whereas the values on a pretest determine the routing to these test forms. Since lMST allows for…

Safety and abuse testing

NASA Technical Reports Server (NTRS)

Younger, G.

1978-01-01

A series of abuse tests on large lithium thionyl chloride cells was initiated. Performance data obtained in testing rectangular 2,000 and 10,000 ampere-hour cells are discussed and graphically presented.

APPLICATION OF STEEL PIPE PILE LOADING TESTS TO DESIGN VERIFICATION OF FOUNDATION OF THE TOKYO GATE BRIDGE

NASA Astrophysics Data System (ADS)

Saitou, Yutaka; Kikuchi, Yoshiaki; Kusakabe, Osamu; Kiyomiya, Osamu; Yoneyama, Haruo; Kawakami, Taiji

Steel sheet pipe pile foundations with large diameter steel pipe sheet pile were used for the foundation of the main pier of the Tokyo Gateway bridge. However, as for the large diameter steel pipe pile, the bearing mechanism including a pile tip plugging effect is still unclear due to lack of the practical examinations even though loading tests are performed on Trans-Tokyo Bay Highway. In the light of the foregoing problems, static pile loading tests both vertical and horizontal directions, a dynamic loading test, and cone penetration tests we re conducted for determining proper design parameters of the ground for the foundations. Design parameters were determined rationally based on the tests results. Rational design verification was obtained from this research.

Proactive Security Testing and Fuzzing

NASA Astrophysics Data System (ADS)

Takanen, Ari

Software is bound to have security critical flaws, and no testing or code auditing can ensure that software is flaw-less. But software security testing requirements have improved radically during the past years, largely due to criticism from security conscious consumers and Enterprise customers. Whereas in the past, security flaws were taken for granted (and patches were quietly and humbly installed), they now are probably one of the most common reasons why people switch vendors or software providers. The maintenance costs from security updates often add to become one of the biggest cost items to large Enterprise users. Fortunately test automation techniques have also improved. Techniques like model-based testing (MBT) enable efficient generation of security tests that reach good confidence levels in discovering zero-day mistakes in software. This technique is called fuzzing.

Designing fire safe interiors.

PubMed

Belles, D W

1992-01-01

Any product that causes a fire to grow large is deficient in fire safety performance. A large fire in any building represents a serious hazard. Multiple-death fires almost always are linked to fires that grow quickly to a large size. Interior finishes have large, continuous surfaces over which fire can spread. They are regulated to slow initial fire growth, and must be qualified for use on the basis of fire tests. To obtain meaningful results, specimens must be representative of actual installation. Variables--such as the substrate, the adhesive, and product thickness and density--can affect product performance. The tunnel test may not adequately evaluate some products, such as foam plastics or textile wall coverings, thermoplastic materials, or materials of minimal mass. Where questions exist, products should be evaluated on a full-scale basis. Curtains and draperies are examples of products that ignite easily and spread flames readily. The present method for testing curtains and draperies evaluates one fabric at a time. Although a fabric tested alone may perform well, fabrics that meet test standards individually sometimes perform poorly when tested in combination. Contents and furnishings constitute the major fuels in many fires. Contents may involve paper products and other lightweight materials that are easily ignited and capable of fast fire growth. Similarly, a small source may ignite many items of furniture that are capable of sustained fire growth. Upholstered furniture can reach peak burning rates in less than 5 minutes. Furnishings have been associated with many multiple-death fires.(ABSTRACT TRUNCATED AT 250 WORDS)

The cost of large numbers of hypothesis tests on power, effect size and sample size.

PubMed

Lazzeroni, L C; Ray, A

2012-01-01

Advances in high-throughput biology and computer science are driving an exponential increase in the number of hypothesis tests in genomics and other scientific disciplines. Studies using current genotyping platforms frequently include a million or more tests. In addition to the monetary cost, this increase imposes a statistical cost owing to the multiple testing corrections needed to avoid large numbers of false-positive results. To safeguard against the resulting loss of power, some have suggested sample sizes on the order of tens of thousands that can be impractical for many diseases or may lower the quality of phenotypic measurements. This study examines the relationship between the number of tests on the one hand and power, detectable effect size or required sample size on the other. We show that once the number of tests is large, power can be maintained at a constant level, with comparatively small increases in the effect size or sample size. For example at the 0.05 significance level, a 13% increase in sample size is needed to maintain 80% power for ten million tests compared with one million tests, whereas a 70% increase in sample size is needed for 10 tests compared with a single test. Relative costs are less when measured by increases in the detectable effect size. We provide an interactive Excel calculator to compute power, effect size or sample size when comparing study designs or genome platforms involving different numbers of hypothesis tests. The results are reassuring in an era of extreme multiple testing.

Results of the NASP Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test Program

NASA Technical Reports Server (NTRS)

Cavolowsky, John A.; Loomis, Mark P.; Deiwert, George S.

1995-01-01

This paper describes the test techniques and results from the National Aerospace Plane Government Work Package 53, the Ames Integrated Mixing Hypersonic Engine (AIMHYE) Scramjet Test program conducted in the NASA Ames 16-Inch Combustion Driven Shock Tunnel. This was a series of near full-scale scramjet combustor tests with the objective to obtain high speed combustor and nozzle data from an engine with injector configurations similar to the NASP E21 and E22a designs. The experimental test approach was to use a large combustor model (80-100% throat height) designed and fabricated for testing in the semi-free jet mode. The conditions tested were similar to the "blue book" conditions at Mach 12, 14, and 16. GWP 53 validated use of large, long test time impulse facilities, specifically the Ames 16-Inch Shock Tunnel, for high Mach number scramjet propulsion testing an integrated test rig (inlet, combustor, and nozzle). Discussion of key features of the test program will include: effects of the 2-D combustor inlet pressure profile; performance of large injectors' fueling system that included nozzlettes, base injection, and film cooling; and heat transfer measurements to the combustor. Significant instrumentation development and application efforts include the following: combustor force balance application for measurement of combustor drag for comparison with integrated point measurements of skin friction; nozzle metric strip for measuring thrust with comparison to integrated pressure measurements; and nonintrusive optical fiber-based diode laser absorption measurements of combustion products for determination of combustor performance. Direct measurements will be reported for specific test article configurations and compared with CFD solutions.

Critical joints in large composite primary aircraft structures. Volume 2: Technology demonstration test report

NASA Technical Reports Server (NTRS)

Bunin, Bruce L.

1985-01-01

A program was conducted to develop the technology for critical structural joints in composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. The results of four large composite multirow bolted joint tests are presented. The tests were conducted to demonstrate the technology for critical joints in highly loaded composite structure and to verify the analytical methods that were developed throughout the program. The test consisted of a wing skin-stringer transition specimen representing a stringer runout and skin splice on the wing lower surface at the side of the fuselage attachment. All tests were static tension tests. The composite material was Toray T-300 fiber with Ciba-Geigy 914 resin in 10 mil tape form. The splice members were metallic, using combinations of aluminum and titanium. Discussions are given of the test article, instrumentation, test setup, test procedures, and test results for each of the four specimens. Some of the analytical predictions are also included.

The Reliability of Teacher Decision-Making in Recommending Accommodations for Large-Scale Tests. Technical Report # 08-01

ERIC Educational Resources Information Center

Tindal, Gerald; Lee, Daesik; Geller, Leanne Ketterlin

2008-01-01

In this paper we review different methods for teachers to recommend accommodations in large scale tests. Then we present data on the stability of their judgments on variables relevant to this decision-making process. The outcomes from the judgments support the need for a more explicit model. Four general categories are presented: student…

Definition of ground test for Large Space Structure (LSS) control verification

NASA Technical Reports Server (NTRS)

Waites, H. B.; Doane, G. B., III; Tollison, D. K.

1984-01-01

An overview for the definition of a ground test for the verification of Large Space Structure (LSS) control is given. The definition contains information on the description of the LSS ground verification experiment, the project management scheme, the design, development, fabrication and checkout of the subsystems, the systems engineering and integration, the hardware subsystems, the software, and a summary which includes future LSS ground test plans. Upon completion of these items, NASA/Marshall Space Flight Center will have an LSS ground test facility which will provide sufficient data on dynamics and control verification of LSS so that LSS flight system operations can be reasonably ensured.

Technology and testing.

PubMed

Quellmalz, Edys S; Pellegrino, James W

2009-01-02

Large-scale testing of educational outcomes benefits already from technological applications that address logistics such as development, administration, and scoring of tests, as well as reporting of results. Innovative applications of technology also provide rich, authentic tasks that challenge the sorts of integrated knowledge, critical thinking, and problem solving seldom well addressed in paper-based tests. Such tasks can be used on both large-scale and classroom-based assessments. Balanced assessment systems can be developed that integrate curriculum-embedded, benchmark, and summative assessments across classroom, district, state, national, and international levels. We discuss here the potential of technology to launch a new era of integrated, learning-centered assessment systems.

Effects of Muscle Atrophy on Motor Control: Cage-size Effects

NASA Technical Reports Server (NTRS)

Stuart, D. G.

1985-01-01

Two populations of male Sprague-Dawley rats were raised either in conventional minimum-specification cages or in a larger cage. When the animals were mature (125 to 150 d), the physiological status of the soleus (SOL) and extensor digitorum longus (EDL) muscles of the small- and large-cage animals were compared. Analysis of whole-muscle properties including the performance of the test muscle during a standardized fatigue test in which the nerve to the test muscle was subjected to supramaximal intermittent stimulation shows: (1) the amplitude, area, mean amplitude, and peak-to-peak rate of the compound muscle action potential decreased per the course of the fatigue test; (2) cage size did not affect the profile of changes for any of the action-potential measurements; (3) changes exhibited in the compound muscle action potential by SOL and EDL were substantially different; and (4) except for SOL of the large-cage rats, there was a high correlation between all four measures of the compound muscle action potential and the peak tetanic force during the fatigue test; i.e., either the electrical activity largely etermines the force profile during the fatigue test or else contractile-related activity substantially affects the compound muscle action potential.

Comparison of Fault Detection Algorithms for Real-time Diagnosis in Large-Scale System. Appendix E

NASA Technical Reports Server (NTRS)

Kirubarajan, Thiagalingam; Malepati, Venkat; Deb, Somnath; Ying, Jie

2001-01-01

In this paper, we present a review of different real-time capable algorithms to detect and isolate component failures in large-scale systems in the presence of inaccurate test results. A sequence of imperfect test results (as a row vector of I's and O's) are available to the algorithms. In this case, the problem is to recover the uncorrupted test result vector and match it to one of the rows in the test dictionary, which in turn will isolate the faults. In order to recover the uncorrupted test result vector, one needs the accuracy of each test. That is, its detection and false alarm probabilities are required. In this problem, their true values are not known and, therefore, have to be estimated online. Other major aspects in this problem are the large-scale nature and the real-time capability requirement. Test dictionaries of sizes up to 1000 x 1000 are to be handled. That is, results from 1000 tests measuring the state of 1000 components are available. However, at any time, only 10-20% of the test results are available. Then, the objective becomes the real-time fault diagnosis using incomplete and inaccurate test results with online estimation of test accuracies. It should also be noted that the test accuracies can vary with time --- one needs a mechanism to update them after processing each test result vector. Using Qualtech's TEAMS-RT (system simulation and real-time diagnosis tool), we test the performances of 1) TEAMSAT's built-in diagnosis algorithm, 2) Hamming distance based diagnosis, 3) Maximum Likelihood based diagnosis, and 4) HidderMarkov Model based diagnosis.

26 CFR 1.6655-4 - Large corporations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 13 2010-04-01 2010-04-01 false Large corporations. 1.6655-4 Section 1.6655-4... corporations. (a) Large corporation defined. The term large corporation means any corporation (or a predecessor corporation) that had taxable income of at least $1,000,000 for any taxable year during the testing period...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2011 CFR

2011-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2013 CFR

2013-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2014 CFR

2014-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2012 CFR

2012-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

27 CFR 478.153 - Semiautomatic assault weapons and large capacity ammunition feeding devices manufactured or...

Code of Federal Regulations, 2010 CFR

2010-04-01

... weapons and large capacity ammunition feeding devices manufactured or imported for the purposes of testing... AMMUNITION Exemptions, Seizures, and Forfeitures § 478.153 Semiautomatic assault weapons and large capacity... weapon, and § 478.40a with respect to large capacity ammunition feeding devices, shall not apply to the...

Test of the CLAS12 RICH large-scale prototype in the direct proximity focusing configuration

DOE PAGES

Anefalos Pereira, S.; Baltzell, N.; Barion, L.; ...

2016-02-11

A large area ring-imaging Cherenkov detector has been designed to provide clean hadron identification capability in the momentum range from 3 GeV/c up to 8 GeV/c for the CLAS12 experiments at the upgraded 12 GeV continuous electron beam accelerator facility of Jefferson Laboratory. The adopted solution foresees a novel hybrid optics design based on aerogel radiator, composite mirrors and high-packed and high-segmented photon detectors. Cherenkov light will either be imaged directly (forward tracks) or after two mirror reflections (large angle tracks). We report here the results of the tests of a large scale prototype of the RICH detector performed withmore » the hadron beam of the CERN T9 experimental hall for the direct detection configuration. As a result, the tests demonstrated that the proposed design provides the required pion-to-kaon rejection factor of 1:500 in the whole momentum range.« less

The effect of wind tunnel wall interference on the performance of a fan-in-wing VTOL model

NASA Technical Reports Server (NTRS)

Heyson, H. H.

1974-01-01

A fan-in-wing model with a 1.07-meter span was tested in seven different test sections with cross-sectional areas ranging from 2.2 sq meters to 265 sq meters. The data from the different test sections are compared both with and without correction for wall interference. The results demonstrate that extreme care must be used in interpreting uncorrected VTOL data since the wall interference may be so large as to invalidate even trends in the data. The wall interference is particularly large at the tail, a result which is in agreement with recently published comparisons of flight and large scale wind tunnel data for a propeller-driven deflected-slipstream configuration. The data verify the wall-interference theory even under conditions of extreme interference. A method yields reasonable estimates for the onset of Rae's minimum-speed limit. The rules for choosing model sizes to produce negligible wall effects are considerably in error and permit the use of excessively large models.

Slicing of Silicon into Sheet Material: Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low Cost Silicon Solar Array Project

NASA Technical Reports Server (NTRS)

Fleming, J. R.

1979-01-01

Testing of low cost low suspension power slurry vehicles is presented. Cutting oils are unlikely to work, but a mineral oil with additives should be workable. Two different abrasives were tested. A cheaper silicon carbide from Norton gave excellent results except for excessive kerf loss: the particles were too big. An abrasive treated for lubricity showed no lubricity improvement in mineral oil vehicle. The bounce fixture was tested for the first time under constant cut rate conditions (rather than constant force). Although the cut was not completed before the blades broke, the blade lifetime of thin (100 micrometer) blades was 120 times the lifetime without the fixture. The large prototype saw completed a successful run, producing 90% cutting yield (849 wafers) at 20 wafers/cm. Although inexperience with large numbers of wafers caused cleaning breakage to reduce this yield to 74%, the yield was high enough that the concept of the large saw is proven workable.

Solar array flight dynamic experiment

NASA Technical Reports Server (NTRS)

Schock, R. W.

1986-01-01

The purpose of the Solar Array Flight Dynamic Experiment (SAFDE) is to demonstrate the feasibility of on-orbit measurement and ground processing of large space structures dynamic characteristics. Test definition or verification provides the dynamic characteristic accuracy required for control systems use. An illumination/measurement system was developed to fly on space shuttle flight STS-31D. The system was designed to dynamically evaluate a large solar array called the Solar Array Flight Experiment (SAFE) that had been scheduled for this flight. The SAFDE system consisted of a set of laser diode illuminators, retroreflective targets, an intelligent star tracker receiver and the associated equipment to power, condition, and record the results. In six tests on STS-41D, data was successfully acquired from 18 retroreflector targets and ground processed, post flight, to define the solar array's dynamic characteristic. The flight experiment proved the viability of on-orbit test definition of large space structures dynamic characteristics. Future large space structures controllability should be greatly enhanced by this capability.

Solar array flight dynamic experiment

NASA Technical Reports Server (NTRS)

Schock, Richard W.

1986-01-01

The purpose of the Solar Array Flight Dynamic Experiment (SAFDE) is to demonstrate the feasibility of on-orbit measurement and ground processing of large space structures dynamic characteristics. Test definition or verification provides the dynamic characteristic accuracy required for control systems use. An illumination/measurement system was developed to fly on Space Shuttle flight STS-31D. The system was designed to dynamically evaluate a large solar array called the Solar Array Flight Experiment (SAFE) that had been scheduled for this flight. The SAFDE system consisted of a set of laser diode illuminators, retroreflective targets, an intelligent star tracker receiver and the associated equipment to power, condition, and record the results. In six tests on STS-41D, data was successfully acquired from 18 retroreflector targets and ground processed, post flight, to define the solar array's dynamic characteristic. The flight experiment proved the viability of on-orbit test definition of large space structures dynamic characteristics. Future large space structures controllability should be greatly enhanced by this capability.

Solar array flight dynamic experiment

NASA Technical Reports Server (NTRS)

Schock, Richard W.

1987-01-01

The purpose of the Solar Array Flight Dynamic Experiment (SAFDE) is to demonstrate the feasibility of on-orbit measurement and ground processing of large space structures' dynamic characteristics. Test definition or verification provides the dynamic characteristic accuracy required for control systems use. An illumination/measurement system was developed to fly on space shuttle flight STS-41D. The system was designed to dynamically evaluate a large solar array called the Solar Array Flight Experiment (SAFE) that had been scheduled for this flight. The SAFDE system consisted of a set of laser diode illuminators, retroreflective targets, an intelligent star tracker receiver and the associated equipment to power, condition, and record the results. In six tests on STS-41D, data was successfully acquired from 18 retroreflector targets and ground processed, post flight, to define the solar array's dynamic characteristic. The flight experiment proved the viability of on-orbit test definition of large space structures dynamic characteristics. Future large space structures controllability should be greatly enhanced by this capability.

Detecting Superior Face Recognition Skills in a Large Sample of Young British Adults

PubMed Central

Bobak, Anna K.; Pampoulov, Philip; Bate, Sarah

2016-01-01

The Cambridge Face Memory Test Long Form (CFMT+) and Cambridge Face Perception Test (CFPT) are typically used to assess the face processing ability of individuals who believe they have superior face recognition skills. Previous large-scale studies have presented norms for the CFPT but not the CFMT+. However, previous research has also highlighted the necessity for establishing country-specific norms for these tests, indicating that norming data is required for both tests using young British adults. The current study addressed this issue in 254 British participants. In addition to providing the first norm for performance on the CFMT+ in any large sample, we also report the first UK specific cut-off for superior face recognition on the CFPT. Further analyses identified a small advantage for females on both tests, and only small associations between objective face recognition skills and self-report measures. A secondary aim of the study was to examine the relationship between trait or social anxiety and face processing ability, and no associations were noted. The implications of these findings for the classification of super-recognizers are discussed. PMID:27713706

Modification of the Ames 40- by 80-foot wind tunnel for component acoustic testing for the second generation supersonic transport

NASA Technical Reports Server (NTRS)

Schmitz, F. H.; Allmen, J. R.; Soderman, P. T.

1994-01-01

The development of a large-scale anechoic test facility where large models of engine/airframe/high-lift systems can be tested for both improved noise reduction and minimum performance degradation is described. The facility development is part of the effort to investigate economically viable methods of reducing second generation high speed civil transport noise during takeoff and climb-out that is now under way in the United States. This new capability will be achieved through acoustic modifications of NASA's second largest subsonic wind tunnel: the 40-by 80-Foot Wind Tunnel at the NASA Ames Research Center. Three major items are addressed in the design of this large anechoic and quiet wind tunnel: a new deep (42 inch (107 cm)) test section liner, expansion of the wind tunnel drive operating envelope at low rpm to reduce background noise, and other promising methods of improving signal-to-noise levels of inflow microphones. Current testing plans supporting the U.S. high speed civil transport program are also outlined.

Large scale cryogenic fluid systems testing

NASA Technical Reports Server (NTRS)

1992-01-01

NASA Lewis Research Center's Cryogenic Fluid Systems Branch (CFSB) within the Space Propulsion Technology Division (SPTD) has the ultimate goal of enabling the long term storage and in-space fueling/resupply operations for spacecraft and reusable vehicles in support of space exploration. Using analytical modeling, ground based testing, and on-orbit experimentation, the CFSB is studying three primary categories of fluid technology: storage, supply, and transfer. The CFSB is also investigating fluid handling, advanced instrumentation, and tank structures and materials. Ground based testing of large-scale systems is done using liquid hydrogen as a test fluid at the Cryogenic Propellant Tank Facility (K-site) at Lewis' Plum Brook Station in Sandusky, Ohio. A general overview of tests involving liquid transfer, thermal control, pressure control, and pressurization is given.

Water flow measurement in large bore pipes: an experimental comparison between two different types of insertion flowmeters.

PubMed

Cascetta, Furio; Palombo, Adolfo; Scalabrini, Gianfranco

2003-04-01

In this paper the metrological behavior of two different insertion flowmeters (magnetic and turbine types) in large water pipes is described. A master-slave calibration was carried out in order to estimate the overall uncertainty of the tested meters. The experimental results show that (i) the magnetic insertion tested flowmeter performs the claimed accuracy (+/- 2%) within all the flow range (20:1); (ii) the insertion turbine tested meter, instead, reaches the claimed accuracy just in the upper zone of the flow range.

Testing of small and large sign support systems FOIL test number : 92F011

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92FOll. The vehicle used for these t...

Testing of small and large sign support systems FOIL test number : 92F036

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 60 mi/h (96.6 km/h), test 92F036. The vehicle used for this ...

The Positive and Negative Consequences of Multiple-Choice Testing

ERIC Educational Resources Information Center

Roediger, Henry L.; Marsh, Elizabeth J.

2005-01-01

Multiple-choice tests are commonly used in educational settings but with unknown effects on students' knowledge. The authors examined the consequences of taking a multiple-choice test on a later general knowledge test in which students were warned not to guess. A large positive testing effect was obtained: Prior testing of facts aided final…

Testing of small and large sign support systems FOIL test number : 92F016

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor : Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign : support system at 20 mi/h (8.9 m/s), test 92F016. The vehicle used for the...

Testing of small and large sign support systems FOIL test number : 92F035

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (32.2 km/h), test 92F035. The vehicle used for this ...

Testing of small and large sign support systems FOIL test number : 92F038

DOT National Transportation Integrated Search

1994-01-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 60 mi/h (96.6 km/h), test 92F038. The vehicle used for this ...

Testing of small and large sign support systems FOIL test number : 92F037

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (32.2 km/h), test 92F037. The vehicle used for this ...

Testing of small and large sign support systems FOIL test number : 92F022

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact laboratory (FOIL) in Mclean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s) , test 92F022. The vehicle used for this t...

Testing of small and large sign support systems FOIL test numbers : 92F040

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 60 mi/h (96.6 km/h), test 92F040. The vehicle used for this ...

Testing of small and large sign support systems FOIL test number : 92F039

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (32.2 km/h) , test 92F039. The vehicle used for this...

Large Space Antenna Systems Technology, 1984

NASA Technical Reports Server (NTRS)

Boyer, W. J. (Compiler)

1985-01-01

Papers are presented which provide a comprehensive review of space missions requiring large antenna systems and of the status of key technologies required to enable these missions. Topic areas include mission applications for large space antenna systems, large space antenna structural systems, materials and structures technology, structural dynamics and control technology, electromagnetics technology, large space antenna systems and the space station, and flight test and evaluation.

Space Shuttle wind tunnel testing program

NASA Technical Reports Server (NTRS)

Whitnah, A. M.; Hillje, E. R.

1984-01-01

A major phase of the Space Shuttle Vehicle (SSV) Development Program was the acquisition of data through the space shuttle wind tunnel testing program. It became obvious that the large number of configuration/environment combinations would necessitate an extremely large wind tunnel testing program. To make the most efficient use of available test facilities and to assist the prime contractor for orbiter design and space shuttle vehicle integration, a unique management plan was devised for the design and development phase. The space shuttle program is reviewed together with the evolutional development of the shuttle configuration. The wind tunnel testing rationale and the associated test program management plan and its overall results is reviewed. Information is given for the various facilities and models used within this program. A unique posttest documentation procedure and a summary of the types of test per disciplines, per facility, and per model are presented with detailed listing of the posttest documentation.

Shake Test Results and Dynamic Calibration Efforts for the Large Rotor Test Apparatus

NASA Technical Reports Server (NTRS)

Russell, Carl R.

2014-01-01

A shake test of the Large Rotor Test Apparatus (LRTA) was performed in an effort to enhance NASAscapability to measure dynamic hub loads for full-scale rotor tests. This paper documents the results of theshake test as well as efforts to calibrate the LRTA balance system to measure dynamic loads.Dynamic rotor loads are the primary source of vibration in helicopters and other rotorcraft, leading topassenger discomfort and damage due to fatigue of aircraft components. There are novel methods beingdeveloped to reduce rotor vibrations, but measuring the actual vibration reductions on full-scale rotorsremains a challenge. In order to measure rotor forces on the LRTA, a balance system in the non-rotatingframe is used. The forces at the balance can then be translated to the hub reference frame to measure therotor loads. Because the LRTA has its own dynamic response, the balance system must be calibrated toinclude the natural frequencies of the test rig.

AXAF-I Low Intensity-Low Temperature (LILT) Testing of the Development Verification Test (DVT) Solar Panel

NASA Technical Reports Server (NTRS)

Alexander, Doug; Edge, Ted; Willowby, Doug

1998-01-01

The planned orbit of the AXAF-I spacecraft will subject the spacecraft to both short, less than 30 minutes for solar and less than 2 hours for lunar, and long earth eclipses and lunar eclipses with combined conjunctive duration of up to 3 to 4 hours. Lack of proper Electrical Power System (EPS) conditioning prior to eclipse may cause loss of mission. To avoid this problem, for short eclipses, it is necessary to off-point the solar array prior to or at the beginning of the eclipse to reduce the battery state of charge (SOC). This yields less overcharge during the high charge currents at sun entry. For long lunar eclipses, solar array pointing and load scheduling must be tailored for the profile of the eclipse. The battery SOC, loads, and solar array current-voltage (I-V) must be known or predictable to maintain the bus voltage within acceptable range. To address engineering concerns about the electrical performance of the AXAF-I solar array under Low Intensity and Low Temperature (LILT) conditions, Marshall Space Flight Center (MSFC) engineers undertook special testing of the AXAF-I Development Verification Test (DVT) solar panel in September-November 1997. In the test the DVT test panel was installed in a thermal vacuum chamber with a large view window with a mechanical "flapper door". The DVT test panel was "flash" tested with a Large Area Pulse Solar Simulator (LAPSS) at various fractional sun intensities and panel (solar cell) temperatures. The testing was unique with regards to the large size of the test article and type of testing performed. The test setup, results, and lessons learned from the testing will be presented.

Evaluating Content Alignment in Computerized Adaptive Testing

ERIC Educational Resources Information Center

Wise, Steven L.; Kingsbury, G. Gage; Webb, Norman L.

2015-01-01

The alignment between a test and the content domain it measures represents key evidence for the validation of test score inferences. Although procedures have been developed for evaluating the content alignment of linear tests, these procedures are not readily applicable to computerized adaptive tests (CATs), which require large item pools and do…

Outdoor Testing Areas | Energy Systems Integration Facility | NREL

Science.gov Websites

of engineers running tests on plug-in hybrid electric vehicles at the Medium-Voltage Outdoor Test large microgrids hub, located in the outdoor low-voltage test yard, includes underground trench access pits for full enclosure of rotating machinery under test. Key Infrastructure Secured underground pits

49 CFR 199.119 - Reporting of anti-drug testing results.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Reporting of anti-drug testing results. 199.119... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.119 Reporting of anti-drug testing results. (a) Each large operator...

49 CFR 199.119 - Reporting of anti-drug testing results.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Reporting of anti-drug testing results. 199.119... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.119 Reporting of anti-drug testing results. (a) Each large operator...

49 CFR 199.119 - Reporting of anti-drug testing results.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Reporting of anti-drug testing results. 199.119... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.119 Reporting of anti-drug testing results. (a) Each large operator...

49 CFR 199.119 - Reporting of anti-drug testing results.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Reporting of anti-drug testing results. 199.119... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.119 Reporting of anti-drug testing results. (a) Each large operator...

49 CFR 199.119 - Reporting of anti-drug testing results.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Reporting of anti-drug testing results. 199.119... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY DRUG AND ALCOHOL TESTING Drug Testing § 199.119 Reporting of anti-drug testing results. (a) Each large operator...

Structural design of a vertical antenna boresight 18.3 by 18.3-m planar near-field antenna measurement system

NASA Technical Reports Server (NTRS)

Sharp, G. R.; Trimarchi, P. A.; Wanhainen, J. S.

1984-01-01

A large very precise near-field planar scanner was proposed for NASA Lewis Research Center. This scanner would permit near-field measurements over a horizontal scan plane measuring 18.3 m by 18.3 m. Large aperture antennas mounted with antenna boresight vertical could be tested up to 60 GHz. When such a large near field scanner is used for pattern testing, the antenna or antenna system under test does not have to be moved. Hence, such antennas and antenna systems can be positioned and supported to simulate configuration in zero g. Thus, very large and heavy machinery that would be needed to accurately move the antennas are avoided. A preliminary investigation was undertaken to address the mechanical design of such a challenging near-field antenna scanner. The configuration, structural design and results of a parametric NASTRAN structural optimization analysis are contained. Further, the resulting design was dynamically analyzed in order to provide resonant frequency information to the scanner mechanical drive system designers. If other large near field scanners of comparable dimensions are to be constructed, the information can be used for design optimization of these also.

Performance of lap splices in large-scale column specimens affected by ASR and/or DEF.

DOT National Transportation Integrated Search

2012-06-01

This research program conducted a large experimental program, which consisted of the design, construction, : curing, deterioration, and structural load testing of 16 large-scale column specimens with a critical lap splice : region, and then compared ...

Built-In Data-Flow Integration Testing in Large-Scale Component-Based Systems

NASA Astrophysics Data System (ADS)

Piel, Éric; Gonzalez-Sanchez, Alberto; Gross, Hans-Gerhard

Modern large-scale component-based applications and service ecosystems are built following a number of different component models and architectural styles, such as the data-flow architectural style. In this style, each building block receives data from a previous one in the flow and sends output data to other components. This organisation expresses information flows adequately, and also favours decoupling between the components, leading to easier maintenance and quicker evolution of the system. Integration testing is a major means to ensure the quality of large systems. Their size and complexity, together with the fact that they are developed and maintained by several stake holders, make Built-In Testing (BIT) an attractive approach to manage their integration testing. However, so far no technique has been proposed that combines BIT and data-flow integration testing. We have introduced the notion of a virtual component in order to realize such a combination. It permits to define the behaviour of several components assembled to process a flow of data, using BIT. Test-cases are defined in a way that they are simple to write and flexible to adapt. We present two implementations of our proposed virtual component integration testing technique, and we extend our previous proposal to detect and handle errors in the definition by the user. The evaluation of the virtual component testing approach suggests that more issues can be detected in systems with data-flows than through other integration testing approaches.

Workplace Drug Testing and Worker Drug Use

PubMed Central

Carpenter, Christopher S

2007-01-01

Objective To examine the nature and extent of the association between workplace drug testing and worker drug use. Data Sources Repeated cross-sections from the 2000 to 2001 National Household Surveys on Drug Abuse (NHSDA) and the 2002 National Survey on Drug Use and Health (NSDUH). Study Design Multivariate logistic regression models of the likelihood of marijuana use are estimated as a function of several different workplace drug policies, including drug testing. Specific questions about penalty severity and the likelihood of detection are used to further evaluate the nature of the association. Principal Findings Individuals whose employers perform drug tests are significantly less likely to report past month marijuana use, even after controlling for a wide array of worker and job characteristics. However, large negative associations are also found for variables indicating whether a firm has drug education, an employee assistance program, or a simple written policy about substance use. Accounting for these other workplace characteristics reduces—but does not eliminate—the testing differential. Frequent testing and severe penalties reduce the likelihood that workers use marijuana. Conclusions Previous studies have interpreted the large negative correlation between workplace drug testing and employee substance use as representing a causal deterrent effect of drug testing. Our results using more comprehensive data suggest that these estimates have been slightly overstated due to omitted variables bias. The overall pattern of results remains largely consistent with the hypothesis that workplace drug testing deters worker drug use. PMID:17362218

Model verification of large structural systems

NASA Technical Reports Server (NTRS)

Lee, L. T.; Hasselman, T. K.

1977-01-01

A methodology was formulated, and a general computer code implemented for processing sinusoidal vibration test data to simultaneously make adjustments to a prior mathematical model of a large structural system, and resolve measured response data to obtain a set of orthogonal modes representative of the test model. The derivation of estimator equations is shown along with example problems. A method for improving the prior analytic model is included.

MULTISPECIES REACTIVE TRACER TEST IN A SAND AND GRAVEL AQUIFER, CAPE COD, MASSACHUSETTS: PART 1: EXPERIMENTAL DESIGN AND TRANSPORT OF BROMIDE AND NICKEL-EDTA TRACERS

EPA Science Inventory

In this report, we summarize a portion of the results of a large-scale tracer test conducted at the U. S. Geological Survey research site on Cape Cod, Massachusetts. The site is located on a large sand and gravel glacial outwash plain in an unconfined aquifer. In April 1993, ab...

Research-Based Recommendations for the Use of Accommodations in Large-Scale Assessments: 2012 Update. Practical Guidelines for the Education of English Language Learners. Book 4

ERIC Educational Resources Information Center

Kieffer, Michael J.; Rivera, Mabel; Francis, David J.

2012-01-01

This report presents results from a new quantitative synthesis of research on the effectiveness and validity of test accommodations for English language learners (ELLs) taking large-scale assessments. In 2006, the Center on Instruction published a review of the literature on test accommodations for ELLs titled "Practical Guidelines for the…

Large wind turbine generators. [NASA program status and potential costs

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Donovon, R. M.

1978-01-01

The large wind turbine portion of the Federal Wind Energy Program consists of two major project efforts: (1) the Mod-0 test bed project for supporting research technology, and (2) the large experimental wind turbines for electric utility applications. The Mod-0 has met its primary objective of providing the entire wind energy program with early operations and performance data. The large experimental wind turbines to be tested in utility applications include three of the Mod-0A (200 kW) type, one Mod-1 (2000 kW), and possibly several of the Mod-2 (2500 kW) designs. This paper presents a description of these wind turbine systems, their programmatic status, and a summary of their potential costs.

Ice Accretion Test Results for Three Large-Scale Swept-Wing Models in the NASA Icing Research Tunnel

NASA Technical Reports Server (NTRS)

Broeren, Andy; Potapczuk, Mark; Lee, Sam; Malone, Adam; Paul, Ben; Woodard, Brian

2016-01-01

The design and certification of modern transport airplanes for flight in icing conditions increasing relies on three-dimensional numerical simulation tools for ice accretion prediction. There is currently no publically available, high-quality, ice accretion database upon which to evaluate the performance of icing simulation tools for large-scale swept wings that are representative of modern commercial transport airplanes. The purpose of this presentation is to present the results of a series of icing wind tunnel test campaigns whose aim was to provide an ice accretion database for large-scale, swept wings.

Efficiency in pathology laboratories: a survey of operations management in NHS bacteriology.

PubMed

Szczepura, A K

1991-01-01

In recent years pathology laboratory services in the U.K. have experienced large increases in demand. But the extent to which U.K. laboratories have introduced controls to limit unnecessary procedures within the laboratory was previously unclear. This paper presents the results of a survey of all 343 NHS bacteriology laboratories which records the extent to which such operations management controls are now in place. The survey shows large differences between laboratories. Quality controls over inputs, the use of screening tests as a culture substitute, the use of direct susceptibility testing, controls over routine antibiotic susceptibility testing, and controls over reporting of results all vary widely. The survey also records the prevalence of hospital antibiotic policies, the extent to which laboratories produce antibiograms for user clinicians, the degree of computerisation in data handling, and the degree of automation in processing specimens. Finally, the survey uncovers a large variation between NHS labs in the percentage of bacteriology samples which prove positive and lead to antibiotic susceptibility tests being carried out.

Fire extinguishing tests -80 with methyl alcohol gasoline (in MIXED)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmstedt, G.; Ryderman, A.; Carlsson, B.

1980-01-01

Large scale tests and laboratory experiments were carried out for estimating the extinguishing effectiveness of three alcohol resistant aqueous film forming foams (AFFF), two alcohol resistant fluoroprotein foams and two detergent foams in various poolfires: gasoline, isopropyl alcohol, acetone, methyl-ethyl ketone, methyl alcohol and M15 (a gasoline, methyl alcohol, isobutene mixture). The scaling down of large scale tests for developing a reliable laboratory method was especially examined. The tests were performed with semidirect foam application, in pools of 50, 11, 4, 0.6, and 0.25 sq m. Burning time, temperature distribution in the liquid, and thermal radiation were determined. An M15more » fire can be extinguished with a detergent foam, but it is impossible to extinguish fires in polar solvents, such as methyl alcohol, acetone, and isopropyl alcohol with detergent foams, AFFF give the best results, and performances with small pools can hardly be correlated with results from large scale fires.« less

Performing a Large-Scale Modal Test on the B2 Stand Crane at NASA's Stennis Space Center

NASA Technical Reports Server (NTRS)

Stasiunas, Eric C.; Parks, Russel A.

2018-01-01

A modal test of NASA’s Space Launch System (SLS) Core Stage is scheduled to occur prior to propulsion system verification testing at the Stennis Space Center B2 test stand. A derrick crane with a 180-ft long boom, located at the top of the stand, will be used to suspend the Core Stage in order to achieve defined boundary conditions. During this suspended modal test, it is expected that dynamic coupling will occur between the crane and the Core Stage. Therefore, a separate modal test was performed on the B2 crane itself, in order to evaluate the varying dynamic characteristics and correlate math models of the crane. Performing a modal test on such a massive structure was challenging and required creative test setup and procedures, including implementing both AC and DC accelerometers, and performing both classical hammer and operational modal analysis. This paper describes the logistics required to perform this large-scale test, as well as details of the test setup, the modal test methods used, and an overview of the results.

Executive decision-making in the domestic sheep.

PubMed

Morton, A Jennifer; Avanzo, Laura

2011-01-31

Two new large animal models of Huntington's disease (HD) have been developed recently, an old world monkey (macaque) and a sheep. Macaques, with their large brains and complex repertoire of behaviors are the 'gold-standard' laboratory animals for testing cognitive function, but there are many practical and ethical issues that must be resolved before HD macaques can be used for pre-clinical research. By contrast, despite their comparable brain size, sheep do not enjoy a reputation for intelligence, and are not used for pre-clinical cognitive testing. Given that cognitive decline is a major therapeutic target in HD, the feasibility of testing cognitive function in sheep must be explored if they are to be considered seriously as models of HD. Here we tested the ability of sheep to perform tests of executive function (discrimination learning, reversal learning and attentional set-shifting). Significantly, we found that not only could sheep perform discrimination learning and reversals, but they could also perform the intradimensional (ID) and extradimensional (ED) set-shifting tasks that are sensitive tests of cognitive dysfunction in humans. Their performance on the ID/ED shifts mirrored that seen in humans and macaques, with significantly more errors to reach criterion in the ED than the ID shift. Thus, sheep can perform 'executive' cognitive tasks that are an important part of the primate behavioral repertoire, but which have never been shown previously to exist in any other large animal. Sheep have great potential, not only for use as a large animal model of HD, but also for studying cognitive function and the evolution of complex behaviours in normal animals.

Executive Decision-Making in the Domestic Sheep

PubMed Central

Morton, A. Jennifer; Avanzo, Laura

2011-01-01

Two new large animal models of Huntington's disease (HD) have been developed recently, an old world monkey (macaque) and a sheep. Macaques, with their large brains and complex repertoire of behaviors are the ‘gold-standard’ laboratory animals for testing cognitive function, but there are many practical and ethical issues that must be resolved before HD macaques can be used for pre-clinical research. By contrast, despite their comparable brain size, sheep do not enjoy a reputation for intelligence, and are not used for pre-clinical cognitive testing. Given that cognitive decline is a major therapeutic target in HD, the feasibility of testing cognitive function in sheep must be explored if they are to be considered seriously as models of HD. Here we tested the ability of sheep to perform tests of executive function (discrimination learning, reversal learning and attentional set-shifting). Significantly, we found that not only could sheep perform discrimination learning and reversals, but they could also perform the intradimensional (ID) and extradimensional (ED) set-shifting tasks that are sensitive tests of cognitive dysfunction in humans. Their performance on the ID/ED shifts mirrored that seen in humans and macaques, with significantly more errors to reach criterion in the ED than the ID shift. Thus, sheep can perform ‘executive’ cognitive tasks that are an important part of the primate behavioral repertoire, but which have never been shown previously to exist in any other large animal. Sheep have great potential, not only for use as a large animal model of HD, but also for studying cognitive function and the evolution of complex behaviours in normal animals. PMID:21305061

Assessment of Disturbance at Three Spatial Scales in Two Large Tropical Reservoirs

EPA Science Inventory

Large reservoirs vary from lentic to lotic systems in time and space. Therefore our objective was to assess disturbance gradients for two large tropical reservoirs and their influences on benthic macroinvertebrates. We tested three hypothesis: 1) a disturbance gradient of environ...

EVA assembly of large space structure element

NASA Technical Reports Server (NTRS)

Bement, L. J.; Bush, H. G.; Heard, W. L., Jr.; Stokes, J. W., Jr.

1981-01-01

The results of a test program to assess the potential of manned extravehicular activity (EVA) assembly of erectable space trusses are described. Seventeen tests were conducted in which six "space-weight" columns were assembled into a regular tetrahedral cell by a team of two "space"-suited test subjects. This cell represents the fundamental "element" of a tetrahedral truss structure. The tests were conducted under simulated zero-gravity conditions. Both manual and simulated remote manipulator system modes were evaluated. Articulation limits of the pressure suit and zero gravity could be accommodated by work stations with foot restraints. The results of this study have confirmed that astronaut EVA assembly of large, erectable space structures is well within man's capabilities.

Spaceport Command and Control System Software Development

NASA Technical Reports Server (NTRS)

Glasser, Abraham

2017-01-01

The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administration's (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This large system requires a large amount of intensive testing that will properly measure the capabilities of the system. Automating the test procedures would save the project money from human labor costs, as well as making the testing process more efficient. Therefore, the Exploration Systems Division (formerly the Electrical Engineering Division) at Kennedy Space Center (KSC) has recruited interns for the past two years to work alongside full-time engineers to develop these automated tests, as well as innovate upon the current automation process.

Small-scale test program to develop a more efficient swivel nozzle thrust deflector for V/STOL lift/cruise engines

NASA Technical Reports Server (NTRS)

Schlundt, D. W.

1976-01-01

The installed performance degradation of a swivel nozzle thrust deflector system obtained during increased vectoring angles of a large-scale test program was investigated and improved. Small-scale models were used to generate performance data for analyzing selected swivel nozzle configurations. A single-swivel nozzle design model with five different nozzle configurations and a twin-swivel nozzle design model, scaled to 0.15 size of the large-scale test hardware, were statically tested at low exhaust pressure ratios of 1.4, 1.3, 1.2, and 1.1 and vectored at four nozzle positions from 0 deg cruise through 90 deg vertical used for the VTOL mode.

Testing of small and large sign support systems FOIL test number : 92F017

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F017. The vehicle used for this te...

Testing of small and large sign support systems FOIL test number : 92F026

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F026. The vehicle used for this te...

Testing of small and large sign support systems FOIL test number : 92F018

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F018. The vehicle used for this te...

Testing of small and large sign support systems FOIL test number : 92F015

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F015. The vehicle used for these t...

Testing of small and large sign support systems FOIL test number : 92F012

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F012. The vehicle used for these t...

Testing of small and large sign support systems FOIL test number : 92F023

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F023. The vehicle used for this te...

Testing of small and large sign support systems FOIL test number : 92F019

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F019. The vehicle used for this te...

Testing of small and large sign support systems FOIL test number : 92F014

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of a crash test performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The test was performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F014. The vehicle used for these t...

Proof test diagrams for Zerodur glass-ceramic

NASA Technical Reports Server (NTRS)

Tucker, D. S.

1991-01-01

Proof test diagrams for Zerodur glass-ceramics are calculated from available fracture mechanics data. It is shown that the environment has a large effect on minimum time-to-failure as predicted by proof test diagrams.

Interfacial stress state present in a 'thin-slice' fibre push-out test

NASA Technical Reports Server (NTRS)

Kallas, M. N.; Koss, D. A.; Hahn, H. T.; Hellmann, J. R.

1992-01-01

An analysis of the stress distributions along the fiber-matrix interface in a 'thin-slice' fiber push-out test is presented for selected test geometries. For the small specimen thicknesses often required to displace large-diameter fibers with high interfacial shear strengths, finite element analysis indicates that large bending stresses may be present. The magnitude of these stresses and their spatial distribution can be very sensitive to the test configuration. For certain test geometries, the specimen configuration itself may alter the interfacial failure process from one which initiates due to a maximum in shear stress near the top surface adjacent to the indentor, to one which involves mixed mode crack growth up from the bottom surface and/or yielding within the matrix near the interface.

Extinguishing agent for magnesium fire, phases 5 and 6

NASA Astrophysics Data System (ADS)

Beeson, H. D.; Tapscott, R. E.; Mason, B. E.

1987-07-01

This report documents the validation testing of the extinguishing system for metal fires developed as part of Phases 1 to 4. The results of this validation testing form the basis of information from which draft military specifications necessary to procure the agent and the agent delivery system may be developed. The developed system was tested against a variety of large-scale metal fire scenarios and the capabilities of the system were assessed. In addition the response of the system to storage and to changes in ambient conditions was tested. Results of this testing revealed that the developed system represented a reliable metal fire extinguishing system that could control and extinguish very large metal fires. The specifications developed for the agent and for the delivery system are discussed in detail.

Large size GEM for Super Bigbite Spectrometer (SBS) polarimeter for Hall A 12GeV program at JLab

DOE PAGES

Gnanvo, Kondo; Liyanage, Nilanga; Nelyubin, Vladimir; ...

2015-05-01

We report on the R&D effort in the design and construction of a large size GEM chamber for the Proton Polarimeter of the Super Bigbite Spectrometer (SBS) in Hall A at Thomas Jefferson National Laboratory (JLab). The SBS Polarimeter trackers consist of two sets of four large chambers of size 200 cm x 60 cm 2. Each chamber is a vertical stack of four GEM modules with an active area of 60 cm x 50 cm. We have built and tested several GEM modules and we describe in this paper the design and construction of the final GEM as wellmore » as the preliminary results on performances from tests carried out in our detector lab and with test beams at (Fermilab).« less

Self-Referencing Hartmann Test for Large-Aperture Telescopes

NASA Technical Reports Server (NTRS)

Korechoff, Robert P.; Oseas, Jeffrey M.

2010-01-01

A method is proposed for end-to-end, full aperture testing of large-aperture telescopes using an innovative variation of a Hartmann mask. This technique is practical for telescopes with primary mirrors tens of meters in diameter and of any design. Furthermore, it is applicable to the entire optical band (near IR, visible, ultraviolet), relatively insensitive to environmental perturbations, and is suitable for ambient laboratory as well as thermal-vacuum environments. The only restriction is that the telescope optical axis must be parallel to the local gravity vector during testing. The standard Hartmann test utilizes an array of pencil beams that are cut out of a well-corrected wavefront using a mask. The pencil beam array is expanded to fill the full aperture of the telescope. The detector plane of the telescope is translated back and forth along the optical axis in the vicinity of the nominal focal plane, and the centroid of each pencil beam image is recorded. Standard analytical techniques are then used to reconstruct the telescope wavefront from the centroid data. The expansion of the array of pencil beams is usually accomplished by double passing the beams through the telescope under test. However, this requires a well-corrected, autocollimation flat, the diameter or which is approximately equal to that of the telescope aperture. Thus, the standard Hartmann method does not scale well because of the difficulty and expense of building and mounting a well-corrected, large aperture flat. The innovation in the testing method proposed here is to replace the large aperture, well-corrected, monolithic autocollimation flat with an array of small-aperture mirrors. In addition to eliminating the need for a large optic, the surface figure requirement for the small mirrors is relaxed compared to that required of the large autocollimation flat. The key point that allows this method to work is that the small mirrors need to operate as a monolithic flat only with regard to tip/tilt and not piston because in collimated space piston has no effect on the image centroids. The problem of aligning the small mirrors in tip/tilt requires a two-part solution. First, each mirror is suspended from a two-axis gimbal. The orientation of the gimbal is maintained by gravity. Second, the mirror is aligned such that the mirror normal is parallel to gravity vector. This is accomplished interferometrically in a test fixture. Of course, the test fixture itself needs to be calibrated with respect to gravity.

Multiple damage identification on a wind turbine blade using a structural neural system

NASA Astrophysics Data System (ADS)

Kirikera, Goutham R.; Schulz, Mark J.; Sundaresan, Mannur J.

2007-04-01

A large number of sensors are required to perform real-time structural health monitoring (SHM) to detect acoustic emissions (AE) produced by damage growth on large complicated structures. This requires a large number of high sampling rate data acquisition channels to analyze high frequency signals. To overcome the cost and complexity of having such a large data acquisition system, a structural neural system (SNS) was developed. The SNS reduces the required number of data acquisition channels and predicts the location of damage within a sensor grid. The sensor grid uses interconnected sensor nodes to form continuous sensors. The combination of continuous sensors and the biomimetic parallel processing of the SNS tremendously reduce the complexity of SHM. A wave simulation algorithm (WSA) was developed to understand the flexural wave propagation in composite structures and to utilize the code for developing the SNS. Simulation of AE responses in a plate and comparison with experimental results are shown in the paper. The SNS was recently tested by a team of researchers from University of Cincinnati and North Carolina A&T State University during a quasi-static proof test of a 9 meter long wind turbine blade at the National Renewable Energy Laboratory (NREL) test facility in Golden, Colorado. Twelve piezoelectric sensor nodes were used to form four continuous sensors to monitor the condition of the blade during the test. The four continuous sensors are used as inputs to the SNS. There are only two analog output channels of the SNS, and these signals are digitized and analyzed in a computer to detect damage. In the test of the wind turbine blade, multiple damages were identified and later verified by sectioning of the blade. The results of damage identification using the SNS during this proof test will be shown in this paper. Overall, the SNS is very sensitive and can detect damage on complex structures with ribs, joints, and different materials, and the system relatively inexpensive and simple to implement on large structures.

49 CFR 178.965 - Drop test.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Conditioning. Rigid plastic Large Packagings and Large Packagings with plastic inner receptacles must be... having essentially the same physical characteristics. (3) The specific gravity and viscosity of a...

Using Satellite Imagery to Assess Large-Scale Habitat Characteristics of Adirondack Park, New York, USA

NASA Astrophysics Data System (ADS)

McClain, Bobbi J.; Porter, William F.

2000-11-01

Satellite imagery is a useful tool for large-scale habitat analysis; however, its limitations need to be tested. We tested these limitations by varying the methods of a habitat evaluation for white-tailed deer ( Odocoileus virginianus) in the Adirondack Park, New York, USA, utilizing harvest data to create and validate the assessment models. We used two classified images, one with a large minimum mapping unit but high accuracy and one with no minimum mapping unit but slightly lower accuracy, to test the sensitivity of the evaluation to these differences. We tested the utility of two methods of assessment, habitat suitability index modeling, and pattern recognition modeling. We varied the scale at which the models were applied by using five separate sizes of analysis windows. Results showed that the presence of a large minimum mapping unit eliminates important details of the habitat. Window size is relatively unimportant if the data are averaged to a large resolution (i.e., township), but if the data are used at the smaller resolution, then the window size is an important consideration. In the Adirondacks, the proportion of hardwood and softwood in an area is most important to the spatial dynamics of deer populations. The low occurrence of open area in all parts of the park either limits the effect of this cover type on the population or limits our ability to detect the effect. The arrangement and interspersion of cover types were not significant to deer populations.

Left gastric vein-based noninvasive test for esophageal varices: a same-day comparison of portal hemodynamic assessment with endoscopic appearance.

PubMed

Maruyama, Hitoshi; Kobayashi, Kazufumi; Kiyono, Soichiro; Ogasawara, Sadahisa; Ooka, Yoshihiko; Suzuki, Eiichiro; Chiba, Tetsuhiro; Kato, Naoya

2018-05-25

To examine the effect of hemodynamic assessment of the left gastric vein (LGV) as a noninvasive test to diagnose esophageal varices (EV) in cirrhosis patients. This cross-sectional study consisted of 229 cirrhosis patients (62.7 ± 11.8 years; Child-Pugh score 5-14). One hundred fifty-four patients had EV (67.2%; small, 53; medium, 71; large, 30). All patients underwent a blood test and Doppler ultrasound followed by upper gastrointestinal endoscopy on the same day. The diagnostic ability for EV was compared between LGV-related findings and the platelet count/spleen diameter ratio (Plt/Spl). The detectability of the LGV was higher in patients with EV (129/144, 89.6%) than in those without (35/75, 46.7%; p < 0.0001), and was higher in those with large EV (30/30, 100%) than in those without (134/199, 67.3%; p = 0.0002). The positive detection of the LGV showed 100% sensitivity and negative predictive value (NPV) to identify large EV in the whole cohort and compensated group (n = 127). The best cutoff value in the LGV diameter was 5.35 mm to identify large EV, showing 0.753 area under the receiver operating characteristic curve (AUROC) with 90% sensitivity and 96.5% NPV. The Plt/Spl showed 62.1% sensitivity and 87.1% NPV, and the best cutoff value was 442.9 to identify large EV with 0.658 AUROC, which was comparable to LGV-based assessment (p = 0.162). This same-day comparison study demonstrated the value of LGV-based noninvasive test to identify large EV with high sensitivity and NPV in cirrhosis patients at a lower cost.

Structural Characterization of Advanced Composite Tow-Steered Shells with Large Cutouts

NASA Technical Reports Server (NTRS)

Wu, K. Chauncey; Turpin, Jason D.; Gardner, Nathaniel W.; Stanford, Bret K.; Martin, Robert A.

2015-01-01

The structural performance of two advanced composite tow-steered shells with large cutouts, manufactured using an automated fiber placement system, is assessed using both experimental and analytical methods. The fiber orientation angles of the shells vary continuously around their circumference from +/- 10 degrees on the crown and keel, to +/- 45 degrees on the sides. The raised surface features on one shell result from application of all 24 tows during each fiber placement system pass, while the second shell uses the tow drop/add capability of the system to achieve a more uniform wall thickness. These unstiffened shells, both without and with small cutouts, were previously tested in axial compression and buckled elastically. In this study, a single unreinforced cutout, scaled to represent a cargo door on a commercial aircraft, is machined into one side of each shell. The prebuckling axial stiffnesses and bifurcation buckling loads of these shells with large cutouts are also computed using linear finite element structural analyses for preliminary comparisons with test data. During testing, large displacements are observed around the large cutouts, but the shells maintain an average of 91 percent of the axial stiffness, and also carry 85 percent of the buckling loads, when compared to the pristine shells without cutouts. These relatively small reductions indicate that there is great potential for using tow steering to mitigate the adverse effects of large cutouts on the overall structural performance.

49 CFR 178.965 - Drop test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Drop test. 178.965 Section 178.965 Transportation... Packagings § 178.965 Drop test. (a) General. The drop test must be conducted for the qualification of all...) Special preparation for the drop test. Large Packagings must be filled in accordance with § 178.960. (c...

Multi-Objective Parallel Test-Sheet Composition Using Enhanced Particle Swarm Optimization

ERIC Educational Resources Information Center

Ho, Tsu-Feng; Yin, Peng-Yeng; Hwang, Gwo-Jen; Shyu, Shyong Jian; Yean, Ya-Nan

2009-01-01

For large-scale tests, such as certification tests or entrance examinations, the composed test sheets must meet multiple assessment criteria. Furthermore, to fairly compare the knowledge levels of the persons who receive tests at different times owing to the insufficiency of available examination halls or the occurrence of certain unexpected…

Measurement and Testing Considerations for Native American Education.

ERIC Educational Resources Information Center

Blanchard, Joseph D.

Some of the general considerations and requirements for the establishment of a testing policy and procedures for a large education system are presented. Testing policy is considered necessary to establish a common understanding of the position of testing in the education program, the facilitation of the use of tests for academic gain, and to…

Can interpreting sediment toxicity tests a mega sites benefit from novel approaches to normalization to address batching of tests?

EPA Science Inventory

Sediment toxicity tests are a key tool used in Ecological Risk Assessments for contaminated sediment sites. Interpreting test results and defining toxicity is often a challenge. This is particularly true at mega sites where the testing regime is large, and by necessity performed ...

Aspheric and freeform surfaces metrology with software configurable optical test system: a computerized reverse Hartmann test

NASA Astrophysics Data System (ADS)

Su, Peng; Khreishi, Manal A. H.; Su, Tianquan; Huang, Run; Dominguez, Margaret Z.; Maldonado, Alejandro; Butel, Guillaume; Wang, Yuhao; Parks, Robert E.; Burge, James H.

2014-03-01

A software configurable optical test system (SCOTS) based on deflectometry was developed at the University of Arizona for rapidly, robustly, and accurately measuring precision aspheric and freeform surfaces. SCOTS uses a camera with an external stop to realize a Hartmann test in reverse. With the external camera stop as the reference, a coordinate measuring machine can be used to calibrate the SCOTS test geometry to a high accuracy. Systematic errors from the camera are carefully investigated and controlled. Camera pupil imaging aberration is removed with the external aperture stop. Imaging aberration and other inherent errors are suppressed with an N-rotation test. The performance of the SCOTS test is demonstrated with the measurement results from a 5-m-diameter Large Synoptic Survey Telescope tertiary mirror and an 8.4-m diameter Giant Magellan Telescope primary mirror. The results show that SCOTS can be used as a large-dynamic-range, high-precision, and non-null test method for precision aspheric and freeform surfaces. The SCOTS test can achieve measurement accuracy comparable to traditional interferometric tests.

Shake Test Results and Dynamic Calibration Efforts for the Large Rotor Test Apparatus

NASA Technical Reports Server (NTRS)

Russell, Carl R.

2014-01-01

Prior to the full-scale wind tunnel test of the UH-60A Airloads rotor, a shake test was completed on the Large Rotor Test Apparatus. The goal of the shake test was to characterize the oscillatory response of the test rig and provide a dynamic calibration of the balance to accurately measure vibratory hub loads. This paper provides a summary of the shake test results, including balance, shaft bending gauge, and accelerometer measurements. Sensitivity to hub mass and angle of attack were investigated during the shake test. Hub mass was found to have an important impact on the vibratory forces and moments measured at the balance, especially near the UH-60A 4/rev frequency. Comparisons were made between the accelerometer data and an existing finite-element model, showing agreement on mode shapes, but not on natural frequencies. Finally, the results of a simple dynamic calibration are presented, showing the effects of changes in hub mass. The results show that the shake test data can be used to correct in-plane loads measurements up to 10 Hz and normal loads up to 30 Hz.

Performing a Large-Scale Modal Test on the B2 Stand Crane at NASA's Stennis Space Center

NASA Technical Reports Server (NTRS)

Stasiunas, Eric C.; Parks, Russel A.; Sontag, Brendan D.

2018-01-01

A modal test of NASA's Space Launch System (SLS) Core Stage is scheduled to occur at the Stennis Space Center B2 test stand. A derrick crane with a 150-ft long boom, located at the top of the stand, will be used to suspend the Core Stage in order to achieve defined boundary conditions. During this suspended modal test, it is expected that dynamic coupling will occur between the crane and the Core Stage. Therefore, a separate modal test was performed on the B2 crane itself, in order to evaluate the varying dynamic characteristics and correlate math models of the crane. Performing a modal test on such a massive structure was challenging and required creative test setup and procedures, including implementing both AC and DC accelerometers, and performing both classical hammer and operational modal analysis. This paper describes the logistics required to perform this large-scale test, as well as details of the test setup, the modal test methods used, and an overview and application of the results.

Towards Risk-Based Test Protocols: Estimating the Contribution of Intensive Testing to the UK Bovine Tuberculosis Problem

PubMed Central

van Dijk, Jan

2013-01-01

Eradicating disease from livestock populations involves the balancing act of removing sufficient numbers of diseased animals without removing too many healthy individuals in the process. As ever more tests for bovine tuberculosis (BTB) are carried out on the UK cattle herd, and each positive herd test triggers more testing, the question arises whether ‘false positive’ results contribute significantly to the measured BTB prevalence. Here, this question is explored using simple probabilistic models of test behaviour. When the screening test is applied to the average UK herd, the estimated proportion of test-associated false positive new outbreaks is highly sensitive to small fluctuations in screening test specificity. Estimations of this parameter should be updated as a priority. Once outbreaks have been confirmed in screening-test positive herds, the following rounds of intensive testing with more sensitive, albeit less specific, tests are highly likely to remove large numbers of false positive animals from herds. Despite this, it is unlikely that significantly more truly infected animals are removed. BTB test protocols should become based on quantified risk in order to prevent the needless slaughter of large numbers of healthy animals. PMID:23717517

Suborbital Applications in Astronomy and Astrophysics

NASA Technical Reports Server (NTRS)

Unwin, Steve; Werner, Mike; Goldsmith, Paul

2012-01-01

Suborbital flights providing access to zero-g in a space environment - Demonstrating new technologies in a relevant environment. - Flight testing of individual elements of a constellation. - Raising the TRL of critical technologies for subsystems on future large missions High-altitude balloons (up to 10 kg payload) -Access to near-space for wavelengths not observable from the ground. -Raising the TRL of critical technologies for subsystems on future large missions. -UV Detector testing.

Space transportation booster engine thrust chamber technology, large scale injector

NASA Technical Reports Server (NTRS)

Schneider, J. A.

1993-01-01

The objective of the Large Scale Injector (LSI) program was to deliver a 21 inch diameter, 600,000 lbf thrust class injector to NASA/MSFC for hot fire testing. The hot fire test program would demonstrate the feasibility and integrity of the full scale injector, including combustion stability, chamber wall compatibility (thermal management), and injector performance. The 21 inch diameter injector was delivered in September of 1991.

Conducting Automated Test Assembly Using the Premium Solver Platform Version 7.0 with Microsoft Excel and the Large-Scale LP/QP Solver Engine Add-In

ERIC Educational Resources Information Center

Cor, Ken; Alves, Cecilia; Gierl, Mark J.

2008-01-01

This review describes and evaluates a software add-in created by Frontline Systems, Inc., that can be used with Microsoft Excel 2007 to solve large, complex test assembly problems. The combination of Microsoft Excel 2007 with the Frontline Systems Premium Solver Platform is significant because Microsoft Excel is the most commonly used spreadsheet…

Threshold Theory Tested in an Organizational Setting: The Relation between Perceived Innovativeness and Intelligence in a Large Sample of Leaders

ERIC Educational Resources Information Center

Christensen, Bo T.; Hartmann, Peter V. W.; Rasmussen, Thomas Hedegaard

2017-01-01

A large sample of leaders (N = 4257) was used to test the link between leader innovativeness and intelligence. The threshold theory of the link between creativity and intelligence assumes that below a certain IQ level (approximately IQ 120), there is some correlation between IQ and creative potential, but above this cutoff point, there is no…

Impedance Eduction in Large Ducts Containing Higher-Order Modes and Grazing Flow

NASA Technical Reports Server (NTRS)

Watson, Willie R.; Jones, Michael G.

2017-01-01

Impedance eduction test data are acquired in ducts with small and large cross-sectional areas at the NASA Langley Research Center. An improved data acquisition system in the large duct has resulted in increased control of the acoustic energy in source modes and more accurate resolution of higher-order duct modes compared to previous tests. Two impedance eduction methods that take advantage of the improved data acquisition to educe the liner impedance in grazing flow are presented. One method measures the axial propagation constant of a dominant mode in the liner test section (by implementing the Kumarsean and Tufts algorithm) and educes the impedance from an exact analytical expression. The second method solves numerically the convected Helmholtz equation and minimizes an objective function to obtain the liner impedance. The two methods are tested first on data synthesized from an exact mode solution and then on measured data. Results show that when the methods are applied to data acquired in the larger duct with a dominant higher-order mode, the same impedance spectra are educed as that obtained in the small duct where only the plane wave mode propagates. This result holds for each higher-order mode in the large duct provided that the higher-order mode is sufficiently attenuated by the liner.

Thermal test of the insulation structure for LH 2 tank by using the large experimental apparatus

NASA Astrophysics Data System (ADS)

Kamiya, S.; Onishi, K.; Konshima, N.; Nishigaki, K.

Conceptual designs of large mass LH 2 (liquid hydrogen) storage systems, whose capacity is 50,000 m3, have been studied in the Japanese hydrogen project, World Energy Network (WE-NET) [K. Fukuda, in: WE-NET Hydrogen Energy Symposium, 1999, P1-P41]. This study has concluded that their thermal insulation structures for the huge LH 2 tanks should be developed. Their actual insulation structures comprise not only the insulation material but also reinforced members and joints. To evaluate their thermal performance correctly, a large test specimen including reinforced members and joints will be necessary. After verifying the thermal performance of a developed large experimental apparatus [S. Kamiya, Cryogenics 40 (1) (2000) 35] for measuring the thermal conductance of various insulation structures, we tested two specimens, a vacuum multilayer insulation (MLI) with a glass fiber reinforced plastic (GFRP) support and a vacuum solid insulation (microtherm ®) with joints. The thermal background test for verifying the thermal design of the experimental apparatus showed that the background heat leak is 0.1 W, small enough to satisfy apparatus performance requirement. The thermal conductance measurements of specimens also showed that thermal heat fluxes of MLI with a GFRP support and microtherm ® are 8 and 5.4 W/m2, respectively.

Performance of lap splices in large-scale column specimens affected by ASR and/or DEF-extension phase.

DOT National Transportation Integrated Search

2015-03-01

A large experimental program, consisting of the design, construction, curing, exposure, and structural load : testing of 16 large-scale column specimens with a critical lap splice region that were influenced by varying : stages of alkali-silica react...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... for transportation and no loss of contents. (2) For fiberboard or wooden Large Packagings, there may be no loss of contents and no permanent deformation that renders the whole Large Packaging, including... deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (4) For the...

The 1980 Large space systems technology. Volume 2: Base technology

NASA Technical Reports Server (NTRS)

Kopriver, F., III (Compiler)

1981-01-01

Technology pertinent to large antenna systems, technology related to large space platform systems, and base technology applicable to both antenna and platform systems are discussed. Design studies, structural testing results, and theoretical applications are presented with accompanying validation data. A total systems approach including controls, platforms, and antennas is presented as a cohesive, programmatic plan for large space systems.

Ballast degradation characterized through triaxial test : research results.

DOT National Transportation Integrated Search

2016-06-01

Transportation Technology Center, Inc. (TTCI) : has supported the development of a large-scale : triaxial test device (Figure 1) for testing ballast : size aggregate materials at the University of : Illinois at Urbana-Champaign (UIUC). This new : tes...

Measurement of the UH-60A Hub Large Rotor Test Apparatus Control System Stiffness

NASA Technical Reports Server (NTRS)

Kufeld, Robert M.

2014-01-01

This purpose of this report is to provides details of the measurement of the control system stiffness of the UH-60A rotor hub mounted on the Large Rotor Test Apparatus (UH-60A/LRTA). The UH-60A/LRTA was used in the 40- by 80-Foot Wind Tunnel to complete the full-scale wind tunnel test portion of the NASA / ARMY UH-60A Airloads Program. This report describes the LRTA control system and highlights the differences between the LRTA and UH-60A aircraft. The test hardware, test setup, and test procedures are also described. Sample results are shown, including the azimuthal variation of the measured control system stiffness for three different loadings and two different dynamic actuator settings. Finally, the azimuthal stiffness is converted to fixed system values using multi-blade transformations for input to comprehensive rotorcraft prediction codes.

Dynamic correction of the laser beam coordinate in fabrication of large-sized diffractive elements for testing aspherical mirrors

NASA Astrophysics Data System (ADS)

Shimansky, R. V.; Poleshchuk, A. G.; Korolkov, V. P.; Cherkashin, V. V.

2017-05-01

This paper presents a method of improving the accuracy of a circular laser system in fabrication of large-diameter diffractive optical elements by means of a polar coordinate system and the results of their use. An algorithm for correcting positioning errors of a circular laser writing system developed at the Institute of Automation and Electrometry, SB RAS, is proposed and tested. Highprecision synthesized holograms fabricated by this method and the results of using these elements for testing the 6.5 m diameter aspheric mirror of the James Webb space telescope (JWST) are described..

Capturing flight system test engineering expertise: Lessons learned

NASA Technical Reports Server (NTRS)

Woerner, Irene Wong

1991-01-01

Within a few years, JPL will be challenged by the most active mission set in history. Concurrently, flight systems are increasingly more complex. Presently, the knowledge to conduct integration and test of spacecraft and large instruments is held by a few key people, each with many years of experience. JPL is in danger of losing a significant amount of this critical expertise, through retirement, during a period when demand for this expertise is rapidly increasing. The most critical issue at hand is to collect and retain this expertise and develop tools that would ensure the ability to successfully perform the integration and test of future spacecraft and large instruments. The proposed solution was to capture and codity a subset of existing knowledge, and to utilize this captured expertise in knowledge-based systems. First year results and activities planned for the second year of this on-going effort are described. Topics discussed include lessons learned in knowledge acquisition and elicitation techniques, life-cycle paradigms, and rapid prototyping of a knowledge-based advisor (Spacecraft Test Assistant) and a hypermedia browser (Test Engineering Browser). The prototype Spacecraft Test Assistant supports a subset of integration and test activities for flight systems. Browser is a hypermedia tool that allows users easy perusal of spacecraft test topics. A knowledge acquisition tool called ConceptFinder which was developed to search through large volumes of data for related concepts is also described and is modified to semi-automate the process of creating hypertext links.

Politics, Economics, and Testing: Some Reflections

ERIC Educational Resources Information Center

Feuer, Michael J.

2011-01-01

In this keynote address, the author shares his reflections on politics, economics, and testing. He focuses on assessment and accountability and begins with some data from large scale written educational testing, "circa 1840". The author argues that people's penchant for accountability and their appetite for standardized testing are, in…

Modeling, Analysis, and Optimization Issues for Large Space Structures

NASA Technical Reports Server (NTRS)

Pinson, L. D. (Compiler); Amos, A. K. (Compiler); Venkayya, V. B. (Compiler)

1983-01-01

Topics concerning the modeling, analysis, and optimization of large space structures are discussed including structure-control interaction, structural and structural dynamics modeling, thermal analysis, testing, and design.

Experimental study of a valveless pulse detonation rocket engine using nontoxic hypergolic propellants

NASA Astrophysics Data System (ADS)

Kan, Brandon K.

A pulsed detonation rocket engine concept was explored through the use of hypergolic propellants in a fuel-centered pintle injector combustor. The combustor design yielded a simple open ended chamber with a pintle type injection element and pressure instrumentation. High-frequency pressure measurements from the first test series showed the presence of large pressure oscillations in excess of 2000 psia at frequencies between 400-600 hz during operation. High-speed video confirmed the high-frequency pulsed behavior and large amounts of after burning. Damaged hardware and instrumentation failure limited the amount of data gathered in the first test series, but the experiments met original test objectives of producing large over-pressures in an open chamber. A second test series proceeded by replacing hardware and instrumentation, and new data showed that pulsed events produced under expanded exhaust prior to pulsing, peak pressures around 8000 psi, and operating frequencies between 400-800 hz. Later hot-fires produced no pulsed behavior despite undamaged hardware. The research succeeded in producing pulsed combustion behavior using hypergolic fuels in a pintle injector setup and provided insights into design concepts that would assist future injector designs and experimental test setups.

Questionnaire-based assessment of executive functioning: Psychometrics.

PubMed

Castellanos, Irina; Kronenberger, William G; Pisoni, David B

2018-01-01

The psychometric properties of the Learning, Executive, and Attention Functioning (LEAF) scale were investigated in an outpatient clinical pediatric sample. As a part of clinical testing, the LEAF scale, which broadly measures neuropsychological abilities related to executive functioning and learning, was administered to parents of 118 children and adolescents referred for psychological testing at a pediatric psychology clinic; 85 teachers also completed LEAF scales to assess reliability across different raters and settings. Scores on neuropsychological tests of executive functioning and academic achievement were abstracted from charts. Psychometric analyses of the LEAF scale demonstrated satisfactory internal consistency, parent-teacher inter-rater reliability in the small to large effect size range, and test-retest reliability in the large effect size range, similar to values for other executive functioning checklists. Correlations between corresponding subscales on the LEAF and other behavior checklists were large, while most correlations with neuropsychological tests of executive functioning and achievement were significant but in the small to medium range. Results support the utility of the LEAF as a reliable and valid questionnaire-based assessment of delays and disturbances in executive functioning and learning. Applications and advantages of the LEAF and other questionnaire measures of executive functioning in clinical neuropsychology settings are discussed.

Silicon micro-fabricated miniature polymer electrolyte fuel cells

NASA Astrophysics Data System (ADS)

Kelley, Shawn Christopher

2000-10-01

The present thesis relates the design, fabrication, and testing of a unique type of silicon-based, miniature fuel cell. The fuel cell electrodes were constructed using standard silicon micro-fabrication techniques, and were used to construct miniature polymer electrolyte fuel cells (PEFCs) using NafionRTM. During testing, methanol and oxygen were the common reactants, but hydrogen and oxygen could be used as well. A novel form of an electrodeposited Pt:Ru alloy was developed for use as a methanol electrooxidation catalyst in the mini-PEFCs. An optimized mini-PEFC design was developed, tested, and compared with large PEFCs on the basis of performance. Mini-PEFC performance was equivalent to that of large PEFCs when scaled for active-area, but was limited by the function of the oxygen electrode. The rate of methanol crossover in a methanol/oxygen mini-PEFC was predicted using Fick's first law and the electrode chip feed-hole area. It was shown that the present mini-PEFC design could function as a fuel cell material test structure. Additionally, the mini-PEFCs were tested as two-cell stacks and as methanol sensors. The miniature, silicon-based PEFCs developed here successfully incorporate the essential aspects of a large PEFC in a smaller, simpler design.

A Method for Assessing the Accuracy of a Photogrammetry System for Precision Deployable Structures

NASA Technical Reports Server (NTRS)

Moore, Ashley

2005-01-01

The measurement techniques used to validate analytical models of large deployable structures are an integral Part of the technology development process and must be precise and accurate. Photogrammetry and videogrammetry are viable, accurate, and unobtrusive methods for measuring such large Structures. Photogrammetry uses Software to determine the three-dimensional position of a target using camera images. Videogrammetry is based on the same principle, except a series of timed images are analyzed. This work addresses the accuracy of a digital photogrammetry system used for measurement of large, deployable space structures at JPL. First, photogrammetry tests are performed on a precision space truss test article, and the images are processed using Photomodeler software. The accuracy of the Photomodeler results is determined through, comparison with measurements of the test article taken by an external testing group using the VSTARS photogrammetry system. These two measurements are then compared with Australis photogrammetry software that simulates a measurement test to predict its accuracy. The software is then used to study how particular factors, such as camera resolution and placement, affect the system accuracy to help design the setup for the videogrammetry system that will offer the highest level of accuracy for measurement of deploying structures.

Monochromatic Measurements of the JPSS-1 VIIRS Polarization Sensitivity

NASA Technical Reports Server (NTRS)

McIntire, Jeff; Moyer, David; Brown, Steven W.; Lykke, Keith R.; Waluschka, Eugene; Oudrari, Hassan; Xiong, Xiaoxiong

2016-01-01

Polarization sensitivity is a critical property that must be characterized for spaceborne remote sensing instruments designed to measure reflected solar radiation. Broadband testing of the first Joint Polar-orbiting Satellite System (JPSS-1) Visible Infrared Imaging Radiometer Suite (VIIRS) showed unexpectedly large polarization sensitivities for the bluest bands on VIIRS (centered between 400 and 600 nm). Subsequent ray trace modeling indicated that large diattenuation on the edges of the bandpass for these spectral bands was the driver behind these large sensitivities. Additional testing using the National Institute of Standards and Technologies Traveling Spectral Irradiance and Radiance Responsivity Calibrations Using Uniform Sources was added to the test program to verify and enhance the model. The testing was limited in scope to two spectral bands at two scan angles; nonetheless, this additional testing provided valuable insight into the polarization sensitivity. Analysis has shown that the derived diattenuation agreed with the broadband measurements to within an absolute difference of about0.4 and that the ray trace model reproduced the general features of the measured data. Additionally, by deriving the spectral responsivity, the linear diattenuation is shown to be explicitly dependent on the changes in bandwidth with polarization state.

Multistage Adaptive Testing for a Large-Scale Classification Test: Design, Heuristic Assembly, and Comparison with Other Testing Modes. ACT Research Report Series, 2012 (6)

ERIC Educational Resources Information Center

Zheng, Yi; Nozawa, Yuki; Gao, Xiaohong; Chang, Hua-Hua

2012-01-01

Multistage adaptive tests (MSTs) have gained increasing popularity in recent years. MST is a balanced compromise between linear test forms (i.e., paper-and-pencil testing and computer-based testing) and traditional item-level computer-adaptive testing (CAT). It combines the advantages of both. On one hand, MST is adaptive (and therefore more…

Testing of small and large sign support systems FOIL test numbers : 92F009 and 92F010

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of two crash tests performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The/tests were performed on a small sign support system at 20 rni/h (8.9 m/s), test 92F009 and 60 mi/h (26.8 m/s),...

Testing of small and large sign support systems FOIL test numbers : 92F024 and 92F025

DOT National Transportation Integrated Search

1994-07-01

This test report contains the results of two crash tests performed at the Federal Outdoor Impact Laboratory (FOIL) in McLean, Virginia. The tests were performed on a small sign support system at 20 mi/h (8.9 m/s), test 92F024, and 60 mi/h (26.8 m/s),...

Pupil Perceptions of National Tests in Science: Perceived Importance, Invested Effort, and Test Anxiety

ERIC Educational Resources Information Center

Eklof, Hanna; Nyroos, Mikaela

2013-01-01

Although large-scale national tests have been used for many years in Swedish compulsory schools, very little is known about how pupils actually react to these tests. The question is relevant, however, as pupil reactions in the test situation may affect test performance as well as future attitudes towards assessment. The question is relevant also…

Relationships between field performance tests in high-level soccer players.

PubMed

Ingebrigtsen, Jørgen; Brochmann, Marit; Castagna, Carlo; Bradley, Paul S; Ade, Jack; Krustrup, Peter; Holtermann, Andreas

2014-04-01

To reduce athlete testing time, the aim of this study was to investigate the relationship between the Yo-Yo intermittent recovery test levels 1 (IR1) and 2 (IR2) performances, maximal sprinting speed (10, 20, and 35 m), repeated sprint ability (RSA; 7 × 35 m), and submaximal heart rates (HRs) after 2 and 4 minutes of the Yo-Yo IR tests by testing 57 high-level soccer players. All players played regularly in one of 3 highest levels of Norwegian soccer and were tested during 3 sessions on 3 consecutive days. Large correlations were observed between Yo-Yo IR1 and IR2 test performances (r = 0.753, p ≤ 0.05). Small and moderate correlations were found between 20- and 35-m sprinting speed and Yo-Yo IR1 performance (r = -0.289 and -0.321, respectively, p ≤ 0.05), whereas 35-m sprinting speed correlated moderately to Yo-Yo IR2 performance (r = -0.371, p ≤ 0.05). Repeated sprint ability at 10, 20, and 35 m all showed moderate to large correlations to Yo-Yo IR1 performance (r = -0.337 to -0.573, p ≤ 0.05). Repeated sprint ability at 20 m (r = -0.348, p ≤ 0.05) and 35 m (r = -0.552, p ≤ 0.01) correlated moderately and largely to Yo-Yo IR2 performance. In addition, moderate and large correlations were found between submaximal Yo-Yo IR1 HRs after 2 (r = -0.483, p ≤ 0.01) and 4 minutes (r = -0.655, p ≤ 0.01) and Yo-Yo IR1 performance, and 2 minutes Yo-Yo IR2 HR and Yo-Yo IR2 performance (r = -0.530, p ≤ 0.01). Intraclass correlation measures of submaximal HR after 2 and 4 minutes of Yo-Yo IR1 test and after 2 minutes of the Yo-Yo IR2 were 0.92 (coefficient of variation [CV] = 4.1%, n = 33), 0.93 (CV = 3.8%, n = 33), and 0.72 (CV = 2.9%, n = 10). Adjusted ordinary least square (OLS) regressions revealed associations (p ≤ 0.05) between sprint speed at 20 and 35 m and Yo-Yo IR1 test performance, but only between 35 m and IR2 test performance (p ≤ 0.05). Further, OLS showed that RSA at 35 m was related to both levels of the Yo-Yo IR test (p ≤ 0.01), and that submaximal HRs after 2 and 4 minutes were independently associated with Yo-Yo IR1 and IR2 performances (p ≤ 0.01). In conclusion, Yo-Yo IR1 and 2 test performances, as well as sprint and RSA performances, correlated very largely, and it may therefore be considered using only one of the Yo-Yo tests and a RSA test, in a general soccer-specific field test protocol. The submaximal HR measures during Yo-Yo tests are reproducible and may be used for frequent, time-efficient, and nonexhaustive testing of intermittent exercise capacity of high-level soccer players.

Teaching Writing and Critical Thinking in Large Political Science Classes

ERIC Educational Resources Information Center

Franklin, Daniel; Weinberg, Joseph; Reifler, Jason

2014-01-01

In the interest of developing a combination of teaching techniques designed to maximize efficiency "and" quality of instruction, we have experimentally tested three separate and relatively common teaching techniques in three large introductory political science classes at a large urban public university. Our results indicate that the…

Free-Suspension Residual Flexibility Testing of Space Station Pathfinder: Comparison to Fixed-Base Results

NASA Technical Reports Server (NTRS)

Tinker, Michael L.

1998-01-01

Application of the free-suspension residual flexibility modal test method to the International Space Station Pathfinder structure is described. The Pathfinder, a large structure of the general size and weight of Space Station module elements, was also tested in a large fixed-base fixture to simulate Shuttle Orbiter payload constraints. After correlation of the Pathfinder finite element model to residual flexibility test data, the model was coupled to a fixture model, and constrained modes and frequencies were compared to fixed-base test. modes. The residual flexibility model compared very favorably to results of the fixed-base test. This is the first known direct comparison of free-suspension residual flexibility and fixed-base test results for a large structure. The model correlation approach used by the author for residual flexibility data is presented. Frequency response functions (FRF) for the regions of the structure that interface with the environment (a test fixture or another structure) are shown to be the primary tools for model correlation that distinguish or characterize the residual flexibility approach. A number of critical issues related to use of the structure interface FRF for correlating the model are then identified and discussed, including (1) the requirement of prominent stiffness lines, (2) overcoming problems with measurement noise which makes the antiresonances or minima in the functions difficult to identify, and (3) the use of interface stiffness and lumped mass perturbations to bring the analytical responses into agreement with test data. It is shown that good comparison of analytical-to-experimental FRF is the key to obtaining good agreement of the residual flexibility values.

OnabotulinumtoxinA therapy for compensatory hyperhidrosis.

PubMed

Adefusika, Jessica A; Brewer, Jerry D

2013-09-01

Compensatory hyperhidrosis due to the treatment for focal primary hyperhidrosis can be devastating and life-altering. The purpose of this paper is to discuss use of the iodine starch test and dilute botulinum toxin to decrease compensatory hyperhidrosis over large surface areas. A large area of the trunk affected by compensatory hyperhidrosis was treated with dilute botulinum toxin therapy using a starch iodine test for localization. The patient had exceptional results with his compensatory truncal sweating returning to normal and remaining stable for multiple months. Treating compensatory hyperhidrosis of large surface areas with dilute botulinum toxin therapy is effective and safe. © 2013 Wiley Periodicals, Inc.

Low energy prompt gamma-ray tests of a large volume BGO detector.

PubMed

Naqvi, A A; Kalakada, Zameer; Al-Anezi, M S; Raashid, M; Khateeb-ur-Rehman; Maslehuddin, M; Garwan, M A

2012-01-01

Tests of a large volume Bismuth Germinate (BGO) detector were carried out to detect low energy prompt gamma-rays from boron and cadmium-contaminated water samples using a portable neutron generator-based Prompt Gamma Neutron Activation Analysis (PGNAA) setup. Inspite of strong interference between the sample- and the detector-associated prompt gamma-rays, an excellent agreement has been observed between the experimental and calculated yields of the prompt gamma-rays, indicating successful application of the large volume BGO detector in the PGNAA analysis of bulk samples using low energy prompt gamma-rays. Copyright © 2011 Elsevier Ltd. All rights reserved.

Advanced Hypervelocity Aerophysics Facility Workshop

NASA Technical Reports Server (NTRS)

Witcofski, Robert D. (Compiler); Scallion, William I. (Compiler)

1989-01-01

The primary objective of the workshop was to obtain a critical assessment of a concept for a large, advanced hypervelocity ballistic range test facility powered by an electromagnetic launcher, which was proposed by the Langley Research Center. It was concluded that the subject large-scale facility was feasible and would provide the required ground-based capability for performing tests at entry flight conditions (velocity and density) on large, complex, instrumented models. It was also concluded that advances in remote measurement techniques and particularly onboard model instrumentation, light-weight model construction techniques, and model electromagnetic launcher (EML) systems must be made before any commitment for the construction of such a facility can be made.

An Introduction to the Computerized Adaptive Testing

ERIC Educational Resources Information Center

Tian, Jian-quan; Miao, Dan-min; Zhu, Xia; Gong, Jing-jing

2007-01-01

Computerized adaptive testing (CAT) has unsurpassable advantages over traditional testing. It has become the mainstream in large scale examinations in modern society. This paper gives a brief introduction to CAT including differences between traditional testing and CAT, the principles of CAT, psychometric theory and computer algorithms of CAT, the…

Equating in Small-Scale Language Testing Programs

ERIC Educational Resources Information Center

LaFlair, Geoffrey T.; Isbell, Daniel; May, L. D. Nicolas; Gutierrez Arvizu, Maria Nelly; Jamieson, Joan

2017-01-01

Language programs need multiple test forms for secure administrations and effective placement decisions, but can they have confidence that scores on alternate test forms have the same meaning? In large-scale testing programs, various equating methods are available to ensure the comparability of forms. The choice of equating method is informed by…

Detecting Test Tampering Using Item Response Theory

ERIC Educational Resources Information Center

Wollack, James A.; Cohen, Allan S.; Eckerly, Carol A.

2015-01-01

Test tampering, especially on tests for educational accountability, is an unfortunate reality, necessitating that the state (or its testing vendor) perform data forensic analyses, such as erasure analyses, to look for signs of possible malfeasance. Few statistical approaches exist for detecting fraudulent erasures, and those that do largely do not…

Extending the Testing Effect to Self-Regulated Learning

ERIC Educational Resources Information Center

Fernandez, Jonathan; Jamet, Eric

2017-01-01

In addition to serving summative assessment purposes, testing has turned out to be a powerful learning tool. However, while the beneficial effect of testing on learning performances has been confirmed in a large body of literature, the question of exactly how testing influences cognitive and metacognitive processes remains unclear. We therefore…

Students' Test Motivation in PISA: The Case of Norway

ERIC Educational Resources Information Center

Hopfenbeck, Therese N.; Kjaernsli, Marit

2016-01-01

Do students make their best effort in large-scale assessment studies such as the "Programme for International Student Assessment" (PISA)? Despite six cycles of PISA surveys from 2000 to 2015, empirical studies regarding students' test motivation and experience of the tests are sparse. The present study examines students' test motivation…

Test Information Targeting Strategies for Adaptive Multistage Testing Designs.

ERIC Educational Resources Information Center

Luecht, Richard M.; Burgin, William

Adaptive multistage testlet (MST) designs appear to be gaining popularity for many large-scale computer-based testing programs. These adaptive MST designs use a modularized configuration of preconstructed testlets and embedded score-routing schemes to prepackage different forms of an adaptive test. The conditional information targeting (CIT)…

On Validity Theory and Test Validation

ERIC Educational Resources Information Center

Sireci, Stephen G.

2007-01-01

Lissitz and Samuelsen (2007) propose a new framework for conceptualizing test validity that separates analysis of test properties from analysis of the construct measured. In response, the author of this article reviews fundamental characteristics of test validity, drawing largely from seminal writings as well as from the accepted standards. He…

49 CFR Appendix D to Part 178 - Thermal Resistance Test

Code of Federal Regulations, 2013 CFR

2013-10-01

... large enough in size to fully house the test outer package without clearance problems. The test oven....3Instrumentation. A calibrated recording device or a computerized data acquisition system with an appropriate range... Configuration. Each outer package material type and design must be tested, including any features such as...

49 CFR Appendix D to Part 178 - Thermal Resistance Test

Code of Federal Regulations, 2014 CFR

2014-10-01

... large enough in size to fully house the test outer package without clearance problems. The test oven....3Instrumentation. A calibrated recording device or a computerized data acquisition system with an appropriate range... Configuration. Each outer package material type and design must be tested, including any features such as...

49 CFR Appendix D to Part 178 - Thermal Resistance Test

Code of Federal Regulations, 2011 CFR

2011-10-01

... large enough in size to fully house the test outer package without clearance problems. The test oven....3Instrumentation. A calibrated recording device or a computerized data acquisition system with an appropriate range... Configuration. Each outer package material type and design must be tested, including any features such as...

49 CFR Appendix D to Part 178 - Thermal Resistance Test

Code of Federal Regulations, 2012 CFR

2012-10-01

... large enough in size to fully house the test outer package without clearance problems. The test oven....3Instrumentation. A calibrated recording device or a computerized data acquisition system with an appropriate range... Configuration. Each outer package material type and design must be tested, including any features such as...

Recommendations for Developing Alternative Test Methods for Screening and Prioritization of Chemicals for Developmental Neurotoxicity

EPA Science Inventory

Developmental neurotoxicity testing (DNT) is perceived by many stakeholders to be an area in critical need of alternative methods to current animal testing protocols and gUidelines. An immediate goal is to develop test methods that are capable of screening large numbers of chemic...

Testing and Validation of the Dynamic Inertia Measurement Method

NASA Technical Reports Server (NTRS)

Chin, Alexander W.; Herrera, Claudia Y.; Spivey, Natalie D.; Fladung, William A.; Cloutier, David

2015-01-01

The Dynamic Inertia Measurement (DIM) method uses a ground vibration test setup to determine the mass properties of an object using information from frequency response functions. Most conventional mass properties testing involves using spin tables or pendulum-based swing tests, which for large aerospace vehicles becomes increasingly difficult and time-consuming, and therefore expensive, to perform. The DIM method has been validated on small test articles but has not been successfully proven on large aerospace vehicles. In response, the National Aeronautics and Space Administration Armstrong Flight Research Center (Edwards, California) conducted mass properties testing on an "iron bird" test article that is comparable in mass and scale to a fighter-type aircraft. The simple two-I-beam design of the "iron bird" was selected to ensure accurate analytical mass properties. Traditional swing testing was also performed to compare the level of effort, amount of resources, and quality of data with the DIM method. The DIM test showed favorable results for the center of gravity and moments of inertia; however, the products of inertia showed disagreement with analytical predictions.

A tonic heat test stimulus yields a larger and more reliable conditioned pain modulation effect compared to a phasic heat test stimulus

PubMed Central

Lie, Marie Udnesseter; Matre, Dagfinn; Hansson, Per; Stubhaug, Audun; Zwart, John-Anker; Nilsen, Kristian Bernhard

2017-01-01

Abstract Introduction: The interest in conditioned pain modulation (CPM) as a clinical tool for measuring endogenously induced analgesia is increasing. There is, however, large variation in the CPM methodology, hindering comparison of results across studies. Research comparing different CPM protocols is needed in order to obtain a standardized test paradigm. Objectives: The aim of the study was to assess whether a protocol with phasic heat stimuli as test-stimulus is preferable to a protocol with tonic heat stimulus as test-stimulus. Methods: In this experimental crossover study, we compared 2 CPM protocols with different test-stimulus; one with tonic test-stimulus (constant heat stimulus of 120-second duration) and one with phasic test-stimuli (3 heat stimulations of 5 seconds duration separated by 10 seconds). Conditioning stimulus was a 7°C water bath in parallel with the test-stimulus. Twenty-four healthy volunteers were assessed on 2 occasions with minimum 1 week apart. Differences in the magnitude and test–retest reliability of the CPM effect in the 2 protocols were investigated with repeated-measures analysis of variance and by relative and absolute reliability indices. Results: The protocol with tonic test-stimulus induced a significantly larger CPM effect compared to the protocol with phasic test-stimuli (P < 0.001). Fair and good relative reliability was found with the phasic and tonic test-stimuli, respectively. Absolute reliability indices showed large intraindividual variability from session to session in both protocols. Conclusion: The present study shows that a CPM protocol with a tonic test-stimulus is preferable to a protocol with phasic test-stimuli. However, we emphasize that one should be cautious to use the CPM effect as biomarker or in clinical decision making on an individual level due to large intraindividual variability. PMID:29392240

A Critical Review of the IELTS Writing Test

ERIC Educational Resources Information Center

Uysal, Hacer Hande

2010-01-01

Administered at local centres in 120 countries throughout the world, IELTS (International English Language Testing System) is one of the most widely used large-scale ESL tests that also offers a direct writing test component. Because of its popularity and its use for making critical decisions about test takers, it is crucial to draw attention to…

A Process for Reviewing and Evaluating Generated Test Items

ERIC Educational Resources Information Center

Gierl, Mark J.; Lai, Hollis

2016-01-01

Testing organization needs large numbers of high-quality items due to the proliferation of alternative test administration methods and modern test designs. But the current demand for items far exceeds the supply. Test items, as they are currently written, evoke a process that is both time-consuming and expensive because each item is written,…

Metal spar/superhybrid shell composite fan blades. [for application to turbofan engins

NASA Technical Reports Server (NTRS)

Salemme, C. T.; Murphy, G. C.

1979-01-01

The use of superhybrid materials in the manufacture and testing of large fan blades is analyzed. The FOD resistance of large metal spar/superhybrid fan blades is investigated. The technical effort reported was comprised of: (1) preliminary blade design; (2) detailed analysis of two selected superhybrid blade designs; (3) manufacture of two process evaluation blades and destructive evaluation; and (4) manufacture and whirligig testing of six prototype superhybrid blades.

Large scale static tests of a tilt-nacelle V/STOL propulsion/attitude control system

NASA Technical Reports Server (NTRS)

1978-01-01

The concept of a combined V/STOL propulsion and aircraft attitude control system was subjected to large scale engine tests. The tilt nacelle/attitude control vane package consisted of the T55 powered Hamilton Standard Q-Fan demonstrator. Vane forces, moments, thermal and acoustic characteristics as well as the effects on propulsion system performance were measured under conditions simulating hover in and out of ground effect.

Are All Ames Strains in the OECD Mutagenicity Test Guideline 471 Useful and Necessary? An Analysis of Large Mutagenicity Data Sets for the IWGT.

EPA Science Inventory

Are All Ames Strains in the OECD Mutagenicity Test Guideline 471 Useful and Necessary? An Analysis of Large Mutagenicity Data Sets for the IWGT R. Williams1, D.M. DeMarini2, L.F. Stankowski Jr.3, E. Zeiger4, K.P. Cross5 1Lhasa, LTD, Leeds, UK 2U.S. EPA, RTP, NC 3Charles River L...

Adapting Pipeline Architectures to Track Developing Aftershock Sequences and Recurrent Explosions

DTIC Science & Technology

2014-02-14

Sumatra earthquake was used to study the performance of subspace detectors to detect and classify events from within a very large (Area = ~250,000 km2... detectors to identify and organize repeating waveforms discovered in multichannel seismic data streams. The framework has been tested and evaluated on...a variety of different test cases from mining blasts in Central Asia to moderate and large earthquake aftershock sequences. The framework performs

Modal Testing of the NPSAT1 Engineering Development Unit

DTIC Science & Technology

2012-07-01

erkläre ich, dass die vorliegende Master Arbeit von mir selbstständig und nur unter Verwendung der angegebenen Quellen und Hilfsmittel angefertigt...logarithmic scale . As 5 Figure 2 shows, natural frequencies are indicated by large values of the first CMIF (peaks), and multiple modes can be detected by...structure’s behavior. Ewins even states, “that no large- scale modal test should be permitted to proceed until some preliminary SDOF analyses have

Group Centric Networking: Large Scale Over the Air Testing of Group Centric Networking

DTIC Science & Technology

2016-11-01

protocol designed to support groups of devices in a local region [4]. It attempts to use the wireless medium to broadcast minimal control information...1) Group Discovery: The goal of the group discovery algo- rithm is to find group nodes without globally flooding control messages. To facilitate this...Large Scale Over-the-Air Testing of Group Centric Networking Logan Mercer, Greg Kuperman, Andrew Hunter, Brian Proulx MIT Lincoln Laboratory

Constitutive Behavior Modelling of AA1100-O AT Large Strain and High Strain Rates

NASA Astrophysics Data System (ADS)

Testa, Gabriel; Iannitti, Gianluca; Ruggiero, Andrew; Gentile, Domenico; Bonora, Nicola

2017-06-01

Constitutive behavior of AA1100-O, provided as extruded bar, was investigated. Microscopic observation showed that the cross-section has a peculiar microstructure consisting in the inner core with a large grain size surrounded by an external annulus with finer grains. Low and high strain rates tensile tests were carried out at different temperature ranging from -190 ° C to 100 ° C. Constitutive behavior was modelled using a modified version of Rusinek & Klepaczko model. Parameters were calibrated on tensile test results. Tests and numerical simulations of symmetric Taylor (RoR) and dynamic tensile extrusion (DTE) tests at different impact velocities were carried out in order to validate the model under complex deformation paths.

Photogrammetry of a Hypersonic Inflatable Aerodynamic Decelerator

NASA Technical Reports Server (NTRS)

Kushner, Laura Kathryn; Littell, Justin D.; Cassell, Alan M.

2013-01-01

In 2012, two large-scale models of a Hypersonic Inflatable Aerodynamic decelerator were tested in the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. One of the objectives of this test was to measure model deflections under aerodynamic loading that approximated expected flight conditions. The measurements were acquired using stereo photogrammetry. Four pairs of stereo cameras were mounted inside the NFAC test section, each imaging a particular section of the HIAD. The views were then stitched together post-test to create a surface deformation profile. The data from the photogram- metry system will largely be used for comparisons to and refinement of Fluid Structure Interaction models. This paper describes how a commercial photogrammetry system was adapted to make the measurements and presents some preliminary results.

Scanning Optical Head with Nontilted Reference Beam: Assuring Nanoradian Accuracy for a New Generation Surface Profiler in the Large-Slope Testing Range

DOE PAGES

Qian, Shinan

2011-01-01

Nmore » anoradian Surface Profilers (SPs) are required for state-of-the-art synchrotron radiation optics and high-precision optical measurements. ano-radian accuracy must be maintained in the large-angle test range. However, the beams' notable lateral motions during tests of most operating profilers, combined with the insufficiencies of their optical components, generate significant errors of ∼ 1  μ rad rms in the measurements. The solution to nano-radian accuracy for the new generation of surface profilers in this range is to apply a scanning optical head, combined with nontilted reference beam. I describe here my comparison of different scan modes and discuss some test results.« less

Gap Test Calibrations And Their Scalin

NASA Astrophysics Data System (ADS)

Sandusky, Harold

2012-03-01

Common tests for measuring the threshold for shock initiation are the NOL large scale gap test (LSGT) with a 50.8-mm diameter donor/gap and the expanded large scale gap test (ELSGT) with a 95.3-mm diameter donor/gap. Despite the same specifications for the explosive donor and polymethyl methacrylate (PMMA) gap in both tests, calibration of shock pressure in the gap versus distance from the donor scales by a factor of 1.75, not the 1.875 difference in their sizes. Recently reported model calculations suggest that the scaling discrepancy results from the viscoelastic properties of PMMA in combination with different methods for obtaining shock pressure. This is supported by the consistent scaling of these donors when calibrated in water-filled aquariums. Calibrations and their scaling are compared for other donors with PMMA gaps and for various donors in water.

Wing force and surface pressure data from a hover test of a 0.658-scale V-22 rotor and wing

NASA Technical Reports Server (NTRS)

Felker, Fort F.; Shinoda, Patrick R.; Heffernan, Ruth M.; Sheehy, Hugh F.

1990-01-01

A hover test of a 0.658-scale V-22 rotor and wing was conducted in the 40 x 80 foot wind tunnel at Ames Research Center. The principal objective of the test was to measure the surface pressures and total download on a large scale V-22 wing in hover. The test configuration consisted of a single rotor and semispan wing on independent balance systems. A large image plane was used to represent the aircraft plane of symmetry. Wing flap angles ranging from 45 to 90 degrees were examined. Data were acquired for both directions of the rotor rotation relative to the wing. Steady and unsteady wing surface pressures, total wing forces, and rotor performance data are presented for all of the configurations that were tested.

Identification challenges for large space structures

NASA Technical Reports Server (NTRS)

Pappa, Richard S.

1990-01-01

The paper examines the on-orbit modal identification of large space structures, stressing the importance of planning and experience, in preparation for the Space Station Structural Characterization Experiment (SSSCE) for the Space Station Freedom. The necessary information to foresee and overcome practical difficulties is considered in connection with seven key factors, including test objectives, dynamic complexity of the structure, data quality, extent of exploratory studies, availability and understanding of software tools, experience with similar problems, and pretest analytical conditions. These factors affect identification success in ground tests. Comparisons with similar ground tests of assembled systems are discussed, showing that the constraints of space tests make these factors more significant. The absence of data and experiences relating to on-orbit modal identification testing is shown to make identification a uniquely mathematical problem, although all spacecraft are constructed and verified by proven engineering methods.

Response of a 2-story test-bed structure for the seismic evaluation of nonstructural systems

NASA Astrophysics Data System (ADS)

Soroushian, Siavash; Maragakis, E. "Manos"; Zaghi, Arash E.; Rahmanishamsi, Esmaeel; Itani, Ahmad M.; Pekcan, Gokhan

2016-03-01

A full-scale, two-story, two-by-one bay, steel braced-frame was subjected to a number of unidirectional ground motions using three shake tables at the UNR-NEES site. The test-bed frame was designed to study the seismic performance of nonstructural systems including steel-framed gypsum partition walls, suspended ceilings and fire sprinkler systems. The frame can be configured to perform as an elastic or inelastic system to generate large floor accelerations or large inter story drift, respectively. In this study, the dynamic performance of the linear and nonlinear test-beds was comprehensively studied. The seismic performance of nonstructural systems installed in the linear and nonlinear test-beds were assessed during extreme excitations. In addition, the dynamic interactions of the test-bed and installed nonstructural systems are investigated.

Statistical significance test for transition matrices of atmospheric Markov chains

NASA Technical Reports Server (NTRS)

Vautard, Robert; Mo, Kingtse C.; Ghil, Michael

1990-01-01

Low-frequency variability of large-scale atmospheric dynamics can be represented schematically by a Markov chain of multiple flow regimes. This Markov chain contains useful information for the long-range forecaster, provided that the statistical significance of the associated transition matrix can be reliably tested. Monte Carlo simulation yields a very reliable significance test for the elements of this matrix. The results of this test agree with previously used empirical formulae when each cluster of maps identified as a distinct flow regime is sufficiently large and when they all contain a comparable number of maps. Monte Carlo simulation provides a more reliable way to test the statistical significance of transitions to and from small clusters. It can determine the most likely transitions, as well as the most unlikely ones, with a prescribed level of statistical significance.

Design, fabrication, and test of a Graphite/Epoxy Metering Shell (GEMS). [for the large space telescope

NASA Technical Reports Server (NTRS)

1975-01-01

A program to design, fabricate and test a dimensionally stable metering structure in support of the large space telescope (LST) program is discussed. Graphite/epoxy was the material selected as the only viable candidate material which can meet the stringent thermal expansion criteria of the LST. A metering shell was designed and fabricated, with emphasis on dimensional stability in conjunction with low cost. Thermal expansion test coupons extracted from the layups of the skin panels indicated the attainment of a coefficient of thermal expansion of 0.0666 micrometers/m K. Subsequent thermal vacuum chamber tests on the complete metering shell demonstrated an expansion of the 2.95-meter overall length of 0.27 micrometers/K. Static and dynamics tests, which demonstrated adequacy with respect to limit loads and stiffness, were also accomplished.

Aluminum alloy AA-6061 and RSA-6061 heat treatment for large mirror applications

NASA Astrophysics Data System (ADS)

Newswander, T.; Crowther, B.; Gubbels, G.; Senden, R.

2013-09-01

Aluminum mirrors and telescopes can be built to perform well if the material is processed correctly and can be relatively low cost and short schedule. However, the difficulty of making high quality aluminum telescopes increases as the size increases, starting with uniform heat treatment through the thickness of large mirror substrates. A risk reduction effort was started to build and test a ½ meter diameter super polished aluminum mirror. Material selection, the heat treatment process and stabilization are the first critical steps to building a successful mirror. In this study, large aluminum blanks of both conventional AA-6061 per AMS-A-22771 and RSA AA-6061 were built, heat treated and stress relieved. Both blanks were destructively tested with a cut through the thickness. Hardness measurements and tensile tests were completed. We present our results in this paper and make suggestions for modification of procedures and future work.

Development of a Large Field-of-View PIV System for Rotorcraft Testing in the 14- x 22-Foot Subsonic Tunnel

NASA Technical Reports Server (NTRS)

Jenkins, Luther N.; Yao, Chung-Sheng; Bartram, Scott M.; Harris, Jerome; Allan, Brian; Wong, Oliver; Mace, W. Derry

2009-01-01

A Large Field-of-View Particle Image Velocimetry (LFPIV) system has been developed for rotor wake diagnostics in the 14-by 22-Foot Subsonic Tunnel. The system has been used to measure three components of velocity in a plane as large as 1.524 meters by 0.914 meters in both forward flight and hover tests. Overall, the system performance has exceeded design expectations in terms of accuracy and efficiency. Measurements synchronized with the rotor position during forward flight and hover tests have shown that the system is able to capture the complex interaction of the body and rotor wakes as well as basic details of the blade tip vortex at several wake ages. Measurements obtained with traditional techniques such as multi-hole pressure probes, Laser Doppler Velocimetry (LDV), and 2D Particle Image Velocimetry (PIV) show good agreement with LFPIV measurements.

Control of Flexible Structures (COFS) Flight Experiment Background and Description

NASA Technical Reports Server (NTRS)

Hanks, B. R.

1985-01-01

A fundamental problem in designing and delivering large space structures to orbit is to provide sufficient structural stiffness and static configuration precision to meet performance requirements. These requirements are directly related to control requirements and the degree of control system sophistication available to supplement the as-built structure. Background and rationale are presented for a research study in structures, structural dynamics, and controls using a relatively large, flexible beam as a focus. This experiment would address fundamental problems applicable to large, flexible space structures in general and would involve a combination of ground tests, flight behavior prediction, and instrumented orbital tests. Intended to be multidisciplinary but basic within each discipline, the experiment should provide improved understanding and confidence in making design trades between structural conservatism and control system sophistication for meeting static shape and dynamic response/stability requirements. Quantitative results should be obtained for use in improving the validity of ground tests for verifying flight performance analyses.

Full-scale flammability test data for validation of aircraft fire mathematical models

NASA Technical Reports Server (NTRS)

Kuminecz, J. F.; Bricker, R. W.

1982-01-01

Twenty-five large scale aircraft flammability tests were conducted in a Boeing 737 fuselage at the NASA Johnson Space Center (JSC). The objective of this test program was to provide a data base on the propagation of large scale aircraft fires to support the validation of aircraft fire mathematical models. Variables in the test program included cabin volume, amount of fuel, fuel pan area, fire location, airflow rate, and cabin materials. A number of tests were conducted with jet A-1 fuel only, while others were conducted with various Boeing 747 type cabin materials. These included urethane foam seats, passenger service units, stowage bins, and wall and ceiling panels. Two tests were also included using special urethane foam and polyimide foam seats. Tests were conducted with each cabin material individually, with various combinations of these materials, and finally, with all materials in the cabin. The data include information obtained from approximately 160 locations inside the fuselage.

The development and testing of the Lens Antenna Deployment Demonstration (LADD) test article

NASA Technical Reports Server (NTRS)

Pugh, Mark L.; Denton, Robert J., Jr.; Strange, Timothy J.

1993-01-01

The USAF Rome Laboratory and NASA Marshall Space Flight Center, through contract to Grumman Corporation, have developed a space-qualifiable test article for the Strategic Defense Initiative Organization to demonstrate the critical structural and mechanical elements of single-axis roll-out membrane deployment for Space Based Radar (SBR) applications. The Lens Antenna Deployment Demonstration (LADD) test article, originally designed as a shuttle-attached flight experiment, is a large precision space structure which is representative of operational designs for space-fed lens antennas. Although the flight experiment was cancelled due to funding constraints and major revisions in the Strategic Defense System (SDS) architecture, development of this test article was completed in June 1989. To take full advantage of the existence of this unique structure, a series of ground tests are proposed which include static, dynamic, and thermal measurements in a simulated space environment. An equally important objective of these tests is the verification of the analytical tools used to design and develop large precision space structures.

Space Propulsion Research Facility (B-2): An Innovative, Multi-Purpose Test Facility

NASA Technical Reports Server (NTRS)

Hill, Gerald M.; Weaver, Harold F.; Kudlac, Maureen T.; Maloney, Christian T.; Evans, Richard K.

2011-01-01

The Space Propulsion Research Facility, commonly referred to as B-2, is designed to hot fire rocket engines or upper stage launch vehicles with up to 890,000 N force (200,000 lb force), after environmental conditioning of the test article in simulated thermal vacuum space environment. As NASA s third largest thermal vacuum facility, and the largest designed to store and transfer large quantities of propellant, it is uniquely suited to support developmental testing associated with large lightweight structures and Cryogenic Fluid Management (CFM) systems, as well as non-traditional propulsion test programs such as Electric and In-Space propulsion. B-2 has undergone refurbishment of key subsystems to support the NASA s future test needs, including data acquisition and controls, vacuum, and propellant systems. This paper details the modernization efforts at B-2 to support the Nation s thermal vacuum/propellant test capabilities, the unique design considerations implemented for efficient operations and maintenance, and ultimately to reduce test costs.

Improving STD testing behavior among high-risk young adults by offering STD testing at a vocational school.

PubMed

Spauwen, Laura W L; Hoebe, Christian J P A; Brouwers, Elfi E H G; Dukers-Muijrers, Nicole H T M

2011-09-30

Chlamydia trachomatis infection (CT) is the most prevalent bacterial STD. Sexually active adolescents and young adults are the main risk group for CT. However, STD testing rates in this group are low since exposed individuals may not feel at risk, owing-at least in part-to the infection's largely asymptomatic nature. Designing new testing environments that are more appealing to young people who are most at risk of acquiring chlamydia can be an important strategy to improve overall testing rates. Here we evaluate the effect of a school-based sexual health program conducted among vocational school students, aiming to obtain better access for counseling and enhance students' STD testing behavior. Adolescents (median age 19 years) attending a large vocational school were provided with sexual health education. Students filled in a questionnaire measuring CT risk and were offered STD testing. Using univariate and multivariate analysis, we assessed differences between men and women in STD-related risk behavior, sexual problems, CT testing behavior and determinants of CT testing behavior. Of 345 participants, 70% were female. Of the 287 sexually active students, 75% were at high risk for CT; one third of women reported sexual problems. Of sexually active participants, 61% provided a self-administered specimen for STD testing. Independent determinants for testing included STD related symptoms and no condom use. All CT diagnoses were in the high-CT-risk group. In the high-risk group, STD testing showed an increased uptake, from 27% (previous self-reported test) to 65% (current test). CT prevalence was 5.7%. Vocational school students are a target population for versatile sexual health prevention. When provided with CT testing facilities and education, self selection mechanisms seemed to increase CT testing rate dramatically in this high-CT-risk population expressing sexual problems. Considering the relative ease of testing and treating large numbers of young adults, offering tests at a vocational school is feasible in reaching adolescents for STD screening. Although cost-effectiveness remains an issue counseling is effective in increasing test rates.

Testing of the BipiColombo Antenna Pointing Mechanism

NASA Astrophysics Data System (ADS)

Campo, Pablo; Barrio, Aingeru; Martin, Fernando

2015-09-01

BepiColombo is an ESA mission to Mercury, its planetary orbiter (MPO) has two antenna pointing mechanism, High gain antenna (HGA) pointing mechanism steers and points a large reflector which is integrated at system level by TAS-I Rome. Medium gain antenna (MGA) APM points a 1.5 m boom with a horn antenna. Both radiating elements are exposed to sun fluxes as high as 10 solar constants without protections.A previous paper [1] described the design and development process to solve the challenges of performing in harsh environment.. Current paper is focused on the testing process of the qualification units. Testing performance of antenna pointing mechanism in its specific environmental conditions has required special set-up and techniques. The process has provided valuable feedback on the design and the testing methods which have been included in the PFM design and tests.Some of the technologies and components were developed on dedicated items priort to EQM, but once integrated, test behaviour had relevant differences.Some of the major concerns for the APM testing are:- Create during the thermal vacuum testing the qualification temperature map with gradients along the APM. From of 200oC to 70oC.- Test in that conditions the radio frequency and pointing performances adding also high RF power to check the power handling and self-heating of the rotary joint.- Test in life up to 12000 equivalent APM revolutions, that is 14.3 million motor revolutions in different thermal conditions.- Measure low thermal distortion of the mechanical chain, being at the same time insulated from external environment and interfaces (55 arcsec pointing error)- Perform deployment of large items guaranteeing during the process low humidity, below 5% to protect dry lubrication- Verify stability with representative inertia of large boom or reflector 20 Kgm2.

Testing and validation of computerized decision support systems.

PubMed

Sailors, R M; East, T D; Wallace, C J; Carlson, D A; Franklin, M A; Heermann, L K; Kinder, A T; Bradshaw, R L; Randolph, A G; Morris, A H

1996-01-01

Systematic, through testing of decision support systems (DSSs) prior to release to general users is a critical aspect of high quality software design. Omission of this step may lead to the dangerous, and potentially fatal, condition of relying on a system with outputs of uncertain quality. Thorough testing requires a great deal of effort and is a difficult job because tools necessary to facilitate testing are not well developed. Testing is a job ill-suited to humans because it requires tireless attention to a large number of details. For these reasons, the majority of DSSs available are probably not well tested prior to release. We have successfully implemented a software design and testing plan which has helped us meet our goal of continuously improving the quality of our DSS software prior to release. While requiring large amounts of effort, we feel that the process of documenting and standardizing our testing methods are important steps toward meeting recognized national and international quality standards. Our testing methodology includes both functional and structural testing and requires input from all levels of development. Our system does not focus solely on meeting design requirements but also addresses the robustness of the system and the completeness of testing.

Fire tests for airplane interior materials

NASA Technical Reports Server (NTRS)

Tustin, E. A.

1980-01-01

Large scale, simulated fire tests of aircraft interior materials were carried out in salvaged airliner fuselage. Two "design" fire sources were selected: Jet A fuel ignited in fuselage midsection and trash bag fire. Comparison with six established laboratory fire tests show that some laboratory tests can rank materials according to heat and smoke production, but existing tests do not characterize toxic gas emissions accurately. Report includes test parameters and test details.

Unmanned Aerial Vehicle Operational Test and Evaluation Lessons Learned

DTIC Science & Technology

2003-12-01

prevented during the test design phase. Test designers should ensure that the appropriate data can be collected in sample sizes large enough to support...encountered during previous tests in an attempt to prevent them from occurring in future tests. The focus of this paper is on UAVs acquired to perform...CHAPTER III TEST DESIGN III. TEST DESIGN Many of the problems encountered during UAV OT could have been prevented during the test

Analysis of large system black box verification test data

NASA Technical Reports Server (NTRS)

Clapp, Kenneth C.; Iyer, Ravishankar Krishnan

1993-01-01

Issues regarding black box, large systems verification are explored. It begins by collecting data from several testing teams. An integrated database containing test, fault, repair, and source file information is generated. Intuitive effectiveness measures are generated using conventional black box testing results analysis methods. Conventional analysts methods indicate that the testing was effective in the sense that as more tests were run, more faults were found. Average behavior and individual data points are analyzed. The data is categorized and average behavior shows a very wide variation in number of tests run and in pass rates (pass rates ranged from 71 percent to 98 percent). The 'white box' data contained in the integrated database is studied in detail. Conservative measures of effectiveness are discussed. Testing efficiency (ratio of repairs to number of tests) is measured at 3 percent, fault record effectiveness (ratio of repairs to fault records) is measured at 55 percent, and test script redundancy (ratio of number of failed tests to minimum number of tests needed to find the faults) ranges from 4.2 to 15.8. Error prone source files and subsystems are identified. A correlational mapping of test functional area to product subsystem is completed. A new adaptive testing process based on real-time generation of the integrated database is proposed.

Ongoing research experiments at the former Soviet nuclear test site in eastern Kazakhstan

USGS Publications Warehouse

Leith, William S.; Kluchko, Luke J.; Konovalov, Vladimir; Vouille, Gerard

2002-01-01

Degelen mountain, located in EasternKazakhstan near the city of Semipalatinsk, was once the Soviets most active underground nuclear test site. Two hundred fifteen nuclear tests were conducted in 181 tunnels driven horizontally into its many ridges--almost twice the number of tests as at any other Soviet underground nuclear test site. It was also the site of the first Soviet underground nuclear test--a 1-kiloton device detonated on October 11, 1961. Until recently, the details of testing at Degelen were kept secret and have been the subject of considerable speculation. However, in 1991, the Semipalatinsk test site became part of the newly independent Republic of Kazakhstan; and in 1995, the Kazakhstani government concluded an agreement with the U.S. Department of Defense to eliminate the nuclear testing infrastructure in Kazakhstan. This agreement, which calls for the "demilitarization of the infrastructure directly associated with the nuclear weapons test tunnels," has been implemented as the "Degelen Mountain Tunnel Closure Program." The U.S. Defense Threat Reduction Agency, in partnership with the Department of Energy, has permitted the use of the tunnel closure project at the former nuclear test site as a foundation on which to support cost-effective, research-and-development-funded experiments. These experiments are principally designed to improve U.S. capabilities to monitor and verify the Comprehensive Test Ban Treaty (CTBT), but have provided a new source of information on the effects of nuclear and chemical explosions on hard, fractured rock environments. These new data extends and confirms the results of recent Russian publications on the rock environment at the site and the mechanical effects of large-scale chemical and nuclear testing. In 1998, a large-scale tunnel closure experiment, Omega-1, was conducted in Tunnel 214 at Degelen mountain. In this experiment, a 100-ton chemical explosive blast was used to test technologies for monitoring the Comprehensive Nuclear Test Ban Treaty, and to calibrate a portion of the CTBT's International Monitoring System. This experiment has also provided important benchmark data on the mechanical behavior of hard, dense, fractured rock, and has demonstrated the feasibility of fielding large-scale calibration explosions, which are specified as a "confidence-building measure" in the CTBT Protocol. Two other large-scale explosion experiments, Omega-2 and Omega-3, are planned for the summer of 1999 and 2000. Like the Tunnel 214 test, the 1999 experiment will include close-in monitoring of near-source effects, as well as contributing to the calibration of key seismic stations for the Comprehensive Test Ban Treaty. The Omega-3 test will examine the effect of multiple blasts on the fractured rock environment.

Heavy hydrocarbon main injector technology

NASA Technical Reports Server (NTRS)

Fisher, S. C.; Arbit, H. A.

1988-01-01

One of the key components of the Advanced Launch System (ALS) is a large liquid rocket, booster engine. To keep the overall vehicle size and cost down, this engine will probably use liquid oxygen (LOX) and a heavy hydrocarbon, such as RP-1, as propellants and operate at relatively high chamber pressures to increase overall performance. A technology program (Heavy Hydrocarbon Main Injector Technology) is being studied. The main objective of this effort is to develop a logic plan and supporting experimental data base to reduce the risk of developing a large scale (approximately 750,000 lb thrust), high performance main injector system. The overall approach and program plan, from initial analyses to large scale, two dimensional combustor design and test, and the current status of the program are discussed. Progress includes performance and stability analyses, cold flow tests of injector model, design and fabrication of subscale injectors and calorimeter combustors for performance, heat transfer, and dynamic stability tests, and preparation of hot fire test plans. Related, current, high pressure, LOX/RP-1 injector technology efforts are also briefly discussed.

Atmospheric characterization on the Kennedy Space Center Shuttle Landing Facility

NASA Astrophysics Data System (ADS)

Ko, Jonathan; Coffaro, Joseph; Wu, Chensheng; Paulson, Daniel; Davis, Christopher

2017-08-01

Large temperature gradients are a known source of strong atmospheric turbulence conditions. Often times these areas of strong turbulence conditions are also accompanied by conditions that make it difficult to conduct long term optical atmospheric tests. The Shuttle Landing Facility (SLF) at the Kennedy Space Center (KSC) provides a prime testing environment that is capable of generating strong atmospheric turbulence yet is also easily accessible for well instrumented testing. The Shuttle Landing Facility features a 5000 m long and 91 m wide concrete runway that provides ample space for measurements of atmospheric turbulence as well as the opportunity for large temperature gradients to form as the sun heats the surface. We present the results of a large aperture LED scintillometer, a triple aperture laser scintillometer, and a thermal probe system that were used to calculate a path averaged and a point calculation of Cn2. In addition, we present the results of the Plenoptic Sensor that was used to calculate a path averaged Cn2 value. These measurements were conducted over a multi-day continuous test with supporting atmospheric and weather data provided by the University of Central Florida.

Impaired flexibility in decision making in rats after administration of the pharmacological stressor yohimbine.

PubMed

Schwager, Andrea L; Haack, Andrew K; Taha, Sharif A

2014-10-01

Stress-induced disruption of decision making has been hypothesized to contribute to drug-seeking behaviors and addiction. Noradrenergic signaling plays a central role in mediating stress responses. However, the effects of acute stress on decision making, and the role of noradrenergic signaling in regulating these effects, have not been well characterized. To characterize changes in decision making caused by acute pharmacological stress, the effects of yohimbine (an α2-adrenergic antagonist) were examined in a delay discounting task. Noradrenergic contributions to decision making were further characterized by examining the effects of propranolol (a β antagonist), prazosin (an α1 antagonist), and guanfacine (an α2 agonist). Sprague-Dawley rats were administered drugs prior to performance on a delay discounting task, in which the delay preceding the large reward increased within each session (ascending delays). To dissociate drug-induced changes in delay sensitivity from behavioral inflexibility, drug effects were subsequently tested in a modified version of the discounting task, in which the delay preceding the large reward decreased within each session (descending delays). Yohimbine increased choice of the large reward when tested with ascending delays but decreased choice of the same large reward when tested with descending delays, suggesting that drug effects could be attributed to perseverative choice of the lever preferred at the beginning of the session. Propranolol increased choice of the large reward when tested with ascending delays. Prazosin and guanfacine had no effect on reward choice. The stress-like effects of yohimbine administration may impair decision making by causing inflexible, perseverative behavior.

Modification of the Rappaport rapid test in large-scale testing for syphilis. Evaluation of the rapid plate and rapid card tests.

PubMed

Ghinsberg, R; Meir, E; Blumstein, G; Kafeman, R

1975-11-01

The Rappaport rapid (RR) plate and card tests were developed as modifications of the RR tube test to permit rapid and inexpensive screening of large numbers of subjects for the diagnosis of syphilis. More than 2,000 sera were examined in parallel by the Venereal Disease Research Laboratory (VDRL) slide test, the rapid plasma reagin (RPR) card test and the RR plate and card tests. There was complete agreement between the RR plate and card tests and the VDRL slide and RPR card tests in 96.6% of sera. In a selected group of 1,530 sera examined, in addition, by the fluorescent treponemal antibody absorption (FTA-ABS) test, there was agreement between the RR plate and card tests and the FTA-ABS test in 74.3% of sera and between the VDRL and RPR tests and the FTA-ABS test in 73.7% of sera. The RR plate test was found to be sufficiently sensitive and specific for the diagnosis of syphilis, although the VDRL slide test is perhaps more sensitive in primary and late latent syphilis. Since the antigen used in the RR tests is colored and stable and the sera do not require inactivation before the test, the tests are easier to perform than the VDRL slide test: the RR plate and card tests could therefore replace the VDRL test as a screening test, with hardly any loss of accuracy.

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Binienda, Wieslaw K.; Goldberg, Robert K.; Roberts, Gary D.

2008-01-01

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Large Space Antenna Systems Technology, part 1

NASA Technical Reports Server (NTRS)

Lightner, E. B. (Compiler)

1983-01-01

A compilation of the unclassified papers presented at the NASA Conference on Large Space Antenna Systems Technology covers the following areas: systems, structures technology, control technology, electromagnetics, and space flight test and evaluation.

Measuring Leakage From Large, Complicated Machinery

NASA Technical Reports Server (NTRS)

Bottemiller, S.

1987-01-01

Test chamber improvised from large bag. Cumulative sizes of leaks in large, complicated machinery measure with relatively simple variation of helium leak-checking technique. When used to check Space Shuttle main engine, new technique gave repeatable and correct results within 0.5 stdin.3/min (1.4 x 10 negative to the seventh power stdm3/s).

To increase controllability of a large flexible antenna by modal optimization

NASA Astrophysics Data System (ADS)

Wang, Feng; Wang, Pengpeng; Jiang, Wenjian

2017-12-01

Large deployable antennas are widely used in aerospace engineering to meet the envelop limit of rocket fairing. The high flexibility and low damping of antenna has proposed critical requirement not only for stability control of the antenna itself, but also for attitude control of the satellite. This paper aims to increase controllability of a large flexible antenna by modal optimization. Firstly, Sensitivity analysis of antenna modal frequencies to stiffness of support structure and stiffness of scanning mechanism are conducted respectively. Secondly, Modal simulation results of antenna frequencies are given, influences of scanning angles on moment of inertia and modal frequencies are evaluated, and modal test is carried out to validate the simulation results. All the simulation and test results show that, after modal optimization the modal characteristic of the large deployable antenna meets the controllability requirement well.

Large pathogenic expansions in the SCA2 and SCA7 genes can be detected by fluorescent repeat-primed polymerase chain reaction assay.

PubMed

Cagnoli, Claudia; Stevanin, Giovanni; Michielotto, Chiara; Gerbino Promis, Giovanni; Brussino, Alessandro; Pappi, Patrizia; Durr, Alexandra; Dragone, Elisa; Viemont, Michelle; Gellera, Cinzia; Brice, Alexis; Migone, Nicola; Brusco, Alfredo

2006-02-01

Large expansions in the SCA2 and SCA7 genes (>100 CAG repeats) have been associated with juvenile and infantile forms of cerebellar ataxias that cannot be detected using standard polymerase chain reaction (PCR). Here, we describe a successful application of the fluorescent short tandem repeat-primed PCR method for accurate identification of these expanded repeats. The test is robust, reliable, and inexpensive and can be used to screen large series of patients, although it cannot give a precise evaluation of the size of the expansion. This test may be of practical value in prenatal diagnoses offered to affected or pre-symptomatic at-risk parents, in which a very large expansion inherited from one of the parents can be missed in the fetus by standard PCR.

Large Pathogenic Expansions in the SCA2 and SCA7 Genes Can Be Detected by Fluorescent Repeat-Primed Polymerase Chain Reaction Assay

PubMed Central

Cagnoli, Claudia; Stevanin, Giovanni; Michielotto, Chiara; Gerbino Promis, Giovanni; Brussino, Alessandro; Pappi, Patrizia; Durr, Alexandra; Dragone, Elisa; Viemont, Michelle; Gellera, Cinzia; Brice, Alexis; Migone, Nicola; Brusco, Alfredo

2006-01-01

Large expansions in the SCA2 and SCA7 genes (>100 CAG repeats) have been associated with juvenile and infantile forms of cerebellar ataxias that cannot be detected using standard polymerase chain reaction (PCR). Here, we describe a successful application of the fluorescent short tandem repeat-primed PCR method for accurate identification of these expanded repeats. The test is robust, reliable, and inexpensive and can be used to screen large series of patients, although it cannot give a precise evaluation of the size of the expansion. This test may be of practical value in prenatal diagnoses offered to affected or pre-symptomatic at-risk parents, in which a very large expansion inherited from one of the parents can be missed in the fetus by standard PCR. PMID:16436644

Large Space Systems Technology, Part 2, 1981

NASA Technical Reports Server (NTRS)

Boyer, W. J. (Compiler)

1982-01-01

Four major areas of interest are covered: technology pertinent to large antenna systems; technology related to the control of large space systems; basic technology concerning structures, materials, and analyses; and flight technology experiments. Large antenna systems and flight technology experiments are described. Design studies, structural testing results, and theoretical applications are presented with accompanying validation data. These research studies represent state-of-the art technology that is necessary for the development of large space systems. A total systems approach including structures, analyses, controls, and antennas is presented as a cohesive, programmatic plan for large space systems.

Development of a Large Scale, High Speed Wheel Test Facility

NASA Technical Reports Server (NTRS)

Kondoleon, Anthony; Seltzer, Donald; Thornton, Richard; Thompson, Marc

1996-01-01

Draper Laboratory, with its internal research and development budget, has for the past two years been funding a joint effort with the Massachusetts Institute of Technology (MIT) for the development of a large scale, high speed wheel test facility. This facility was developed to perform experiments and carry out evaluations on levitation and propulsion designs for MagLev systems currently under consideration. The facility was developed to rotate a large (2 meter) wheel which could operate with peripheral speeds of greater than 100 meters/second. The rim of the wheel was constructed of a non-magnetic, non-conductive composite material to avoid the generation of errors from spurious forces. A sensor package containing a multi-axis force and torque sensor mounted to the base of the station, provides a signal of the lift and drag forces on the package being tested. Position tables mounted on the station allow for the introduction of errors in real time. A computer controlled data acquisition system was developed around a Macintosh IIfx to record the test data and control the speed of the wheel. This paper describes the development of this test facility. A detailed description of the major components is presented. Recently completed tests carried out on a novel Electrodynamic (EDS) suspension system, developed by MIT as part of this joint effort are described and presented. Adaptation of this facility for linear motor and other propulsion and levitation testing is described.

Testing and checkout experiences in the National Transonic Facility since becoming operational

NASA Technical Reports Server (NTRS)

Bruce, W. E., Jr.; Gloss, B. B.; Mckinney, L. W.

1988-01-01

The U.S. National Transonic Facility, constructed by NASA to meet the national needs for High Reynolds Number Testing, has been operational in a checkout and test mode since the operational readiness review (ORR) in late 1984. During this time, there have been problems centered around the effect of large temperature excursions on the mechanical movement of large components, the reliable performance of instrumentation systems, and an unexpected moisture problem with dry insulation. The more significant efforts since the ORR are reviewed and NTF status concerning hardware, instrumentation and process controls systems, operating constraints imposed by the cryogenic environment, and data quality and process controls is summarized.

Wind-turbine-performance assessment

NASA Astrophysics Data System (ADS)

Vachon, W. A.

1982-06-01

An updated summary of recent test data and experiences is reported from both federally and privately funded large wind turbine (WT) development and test programs, and from key WT programs in Europe. Progress and experiences on both the cluster of three MOD-2 2.5-MW WT's, the MOD-1 2-MW WT, and other WT installations are described. An examination of recent test experiences and plans from approximately five privately funded large WT programs in the United States indicates that, during machine checkout and startup, technical problems are identified, which require and startup, a number of technical problems are identified, which will require design changes and create program delays.

Laser-induced damage of intrinsic and extrinsic defects by picosecond pulses on multilayer dielectric coatings for petawatt-class lasers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Negres, Raluca A.; Carr, Christopher W.; Laurence, Ted A.

2016-08-01

Here, we describe a damage testing system and its use in investigating laser-induced optical damage initiated by both intrinsic and extrinsic precursors on multilayer dielectric coatings suitable for use in high-energy, large-aperture petawatt-class lasers. We employ small-area damage test methodologies to evaluate the intrinsic damage resistance of various coatings as a function of deposition methods and coating materials under simulated use conditions. In addition, we demonstrate that damage initiation by raster scanning at lower fluences and growth threshold testing are required to probe the density of extrinsic defects, which will limit large-aperture optics performance.

Development of a superconductor magnetic suspension and balance prototype facility for studying the feasibility of applying this technique to large scale aerodynamic testing

NASA Technical Reports Server (NTRS)

Zapata, R. N.; Humphris, R. R.; Henderson, K. C.

1975-01-01

The basic research and development work towards proving the feasibility of operating an all-superconductor magnetic suspension and balance device for aerodynamic testing is presented. The feasibility of applying a quasi-six-degree-of freedom free support technique to dynamic stability research was studied along with the design concepts and parameters for applying magnetic suspension techniques to large-scale aerodynamic facilities. A prototype aerodynamic test facility was implemented. Relevant aspects of the development of the prototype facility are described in three sections: (1) design characteristics; (2) operational characteristics; and (3) scaling to larger facilities.

Assessment of the State-of-the-Art in the Design and Manufacturing of Large Composite Structure

NASA Technical Reports Server (NTRS)

Harris, C. E.

2001-01-01

This viewgraph presentation gives an assessment of the state-of-the-art in the design and manufacturing of large component structures, including details on the use of continuous fiber reinforced polymer matrix composites (CFRP) in commercial and military aircraft and in space launch vehicles. Project risk mitigation plans must include a building-block test approach to structural design development, manufacturing process scale-up development tests, and pre-flight ground tests to verify structural integrity. The potential benefits of composite structures justifies NASA's investment in developing the technology. Advanced composite structures technology is enabling to virtually every Aero-Space Technology Enterprise Goal.

Effects of Aromatherapy on Test Anxiety and Performance in College Students

ERIC Educational Resources Information Center

Dunnigan, Jocelyn Marie

2013-01-01

Test anxiety is a complex, multidimensional construct composed of cognitive, affective, and behavioral components that have been shown to negatively affect test performance. Furthermore, test anxiety is a pervasive problem in modern society largely related to the evaluative nature of educational programs, therefore meriting study of its nature,…